WorldWideScience

Sample records for rubber latex films

  1. Extractable protein content of radiation vulcanized natural rubber latex films

    International Nuclear Information System (INIS)

    Ma'zam Md Said; Wan Manshol Wan Zin

    1996-01-01

    The effects of processing conditions on extractable protein content of coagulant dipped radiation vulcanized natural rubber latex films have been investigated. Drying of wet-gel of radiation vulcanized latex films even at a relatively low temperature of 70 degree C resulted in increases of extractable protein content of the films. The extractable protein content is dependent upon both the temperature and time of drying of wet-gel deposit. Wet-gel leaching of film alone is not adequate to reduce the extractable protein content of films to low levels. Combination of wet-gel leaching, post-leaching, a dip in corn starch slurry, followed by drying at a low temperature of 70 degree C reduces the extractable protein content of films to very low levels

  2. Aspects of Degradability and Aging of Natural Rubber Latex Films Obtained by Induced Ionizing Radiation Processes of Latex Vulcanization

    International Nuclear Information System (INIS)

    Parra, D. F.

    2006-01-01

    This study refers to the degradability of NRLF, natural rubber latex films, obtained by ionizing radiation. Three types of NRLF were prepared: irradiated latex, irradiated latex with about 1% of soy lecithin and sulfur-vulcanized latex, by cold vulcanization process. The films were buried in vases of two different kinds of soil: common soil and common soil with earthworm humus. Fast aging tests in laboratory with exposition to ultraviolet rays were done in irradiated latex films and irradiated latex films with soy lecithin. The results obtained after ten months of tests with buried films agree with the results of the fast aging tests, showing singularities of each type of soil and each kind of latex process. It also shows how weather inclemency can induce the films degradation process. The sulfur-vulcanized films were weakly degraded when buried. The films with lecithin and buried in vase with only common soil showed the biggest mass loss, but the films with lecithin buried in vases with common earthworm humus and soil increased their weigh and dimensions due to fungi formation. The irradiated latex films are more degradable then the sulfur-vulcanized films. The irradiated latex film, unlike the sulfur vulcanized film, showed high fungi colonization when buried. We conclude that the irradiated latex films are more easily biodegradable than the sulfur vulcanized latex films. The biodegradability increases with the addition of small amounts of soy lecithin (∼1%). The mechanical resistance of the buried films decreased related to the non-buried ones, proving that the outdoor aging in soil and the presence of fungi in the films can modify the mechanical properties of the irradiated latex owing to the biodegradation

  3. Effect of cellulose nanocrystals from corn cob with dispersion agent polyvinyl pyrrolidone in natural rubber latex film after aging treatment

    Science.gov (United States)

    Harahap, H.; Ridha, M.; Halimatuddahliana; Taslim; Iriany

    2018-02-01

    This study about the resistance of natural rubber latex films using nanocrystals cellulose filler from corn cob waste by aging treatment. Corn cob used as organic filler composed of cellulose, hemicellulose, and lignin. Each component has a potential for reuse, such as cellulose. Cellulose from corn cob has potential application as a filler prepared by hydrolysis process using a strong acid. The producing of natural rubber latex films through coagulant dowsing process. This research started with the pre-vulcanization process of natural rubber latex at 70 °C and followed by process of vulcanization at 110 °C for 20 minutes. Natural rubber latex films that have been produced continued with the aging treatment at 70 °C for 168 hours. The mechanical properties of natural rubber latex films after aging treatment are the tensile strength, elongation at break, M100 and M300 have performed.

  4. Effect of Antioxidants on Radiation Vulcanization Natural Rubber Latex (RVNRL) Film

    International Nuclear Information System (INIS)

    Syuhada Ramli; Sofian Ibrahim; Muhammad Saiful Omar

    2015-01-01

    This paper presents the results on the effects of different antioxidants used in Radiation Vulcanization Natural Rubber Latex (RVNRL)) films between 0 to 10 weeks monitoring. Antioxidants used for the RVNRL formulation were Aquanox LP, Irganox and Wingstay L. Color difference evaluation by using Chroma Meter CR-400 found that RVNRL film with Irganox was the most stained yellowish after 8 weeks monitoring. Tensile strength for RVNRL with Aquanox found achieved the optimum strength between 25.4 to 27.13 mPa. The scanner electron microscopic (SEM) indicated more Aquanox molecules to penetrate and interact with the rubber molecule, thus becoming more effective inhibitor against its oxidative ageing. (author)

  5. Effect of heterogeneous distribution of crosslink density on physical properties of radiation vulcanized NR (Natural Rubber) latex film

    International Nuclear Information System (INIS)

    Keizo Makuuchi; Fumio Yoshii; Miura, H.; Murakami, K.

    1996-01-01

    Thus a study has been carried out to investigate the effect of particle to particle variation in crosslink density on physical properties of radiation vulcanized NR latex film. NR latex was irradiated in small bottle by γ rays without vulcanization accelerator to provide latex rubber particles having homogeneous distribution of crosslink density. The doses were 30, 50, 100, 250, 300, 400, 500 and 600 kGy. Weight swelling ratio, gel fraction, tensile strength and elongation at break of the latex film from the mixed latex were measured. The vulcanization dose of this latex was 250 kGy. Then the two different latexes were mixed in a such way to adjust the average dose of 250 kGy to prepare a latex consisting of rubber particles having heterogeneous distribution of crosslink density. Tensile strength of the latex film was depressed by mixing. The reduction increased with increasing the decrease of gel fraction by mixing. However the reduction was not serious when the dose difference of two latexes was less than 200 kGy

  6. Toxicological evaluation of natural rubber latex film vulcanized with ionizing radiation

    International Nuclear Information System (INIS)

    Campos, Vania E.; Higa, Olga Z.; Guedes, Selma M.L.; Hanada, Seico

    1999-01-01

    The industrial vulcanization of natural rubber latex (NRL) is made worldwide by conventional process using sulphur, but it can be made by an alternative process using ionizing radiation. The main advantages of this process are related to absence of toxic effect promoted by chemical substances added to the NRL on the conventional process. In this research was tested the toxicological properties of the films vulcanized by the alternative process in relation to that vulcanized by the conventional process. The toxicity was evaluated by in vitro cytotoxicity assay and in vivo systemic toxicity assay. The results showed that vulcanized films by gamma ray are less cytotoxic. The systemic toxicity assay showed that only the vulcanized film using sulphur induced allaying and motor in coordination on the animals for a short period of time. these results evidence the less cytotoxic properties of vulcanized films by gamma ray in relation to that vulcanized by conventional process using sulphur. (author)

  7. Radiation vulcanization of Philippine natural rubber latex

    International Nuclear Information System (INIS)

    Dela Rosa, A.M.; Abad, L.V.; Sta.Ana-Relleve, L.P.; Tranquilan-Aranilla, C.O.; Pascual, C.L.

    1996-01-01

    The response of Philippine natural rubber latex to irradiation vulcanization and the stability of the irradiated natural rubber latex (INRL) upon storage and aging were investigated. Commercially available high ammonia (HA) concentrated latices obtained from various rubber plantations in Mindanao island were treated with 5 phr of n-butyl acrylate (nBA), and gamma-irradiated at the PNRI 60 Co irradiation facility at a dose rate of 2.57 kGy/hr. Unirradiated cast latex films gave different green strengths which varied from 2-11 MPa. Cast films from INRL exhibited maximum tensile strengths were obtained from cast films with low Mg and high nitrogen contents. Thermal analysis using thermogravimetry (TG) revealed one major decomposition product at 374 o -377 o C. Its rate of decomposition decreased to a minimum at 15 kGy, then increased as radiation dose was increased. This trend correlated well with the tensile strength measurements. The stability of the INRL upon storage and aging is an essential parameter to the rubbe latex industry. For storage studies, INRL was stored for various periods of time. It was found that the pH and total solids content of the stored INRL did not change significantly after 12 months of storage; the MST values remained at above 1000 seconds, and the viscosity decreased with time. The cast films exhibited a decline in tensile strength, modulus 300% , and crosslinking density upon storage. While there were observed changes in the physical properties of the INRL during the storage period, the data indicate that these properties were within values acceptable to the latex industry. Tests on the aging properties of INRL films were undertaken. It was shown that among the chemical antioxidants presently used by the latex industry, TNPP demonstrated the highest antioxidant property, followed by Antage DAHQ and Vulcanox BKF. Our data indicate that the natural rubber latex produced and processed in the Philippines is suited for radiation vulcanization

  8. Biodegradability and aging study of rubber films obtained by gamma radiation vulcanization processes of latex

    International Nuclear Information System (INIS)

    Martins, Carlos Felipe Pinto

    2005-01-01

    The natural rubber latex (NRL) is industrially crosslinked by the conventional process of vulcanization, which uses sulphur and heat. Otherwise, the network can also be done by the alternative process with ionizing radiation. In this work the crosslinking of NRL was studied by the comparison of the conventional vulcanization system and the ionizing radiation process of 60 C source. The products obtained, the irradiated latex, the irradiated latex with approximately 1% of soy lecithin and the sulphur vulcanized latex were tested by accelerated aging with ultraviolet (UV) and outdoor aging with compostage, tensile strength at break, swelling and gel fraction, fungi micro biota, scanning electron microscopy (SEM), infrared spectroscopy (FTIR) and thermogravimetry and differential scanning calorimetry analysis (TG and DSC). The results showed that the aging with microorganisms have a great influence in the physical properties of the samples. The thermal stability order observed showed that the sulphur vulcanized latex is more resistant, what is probably associated to a network more stable under the aging conditions. On the other hand, the irradiated latex showed intense biodegradation aspects, particularly with the presence of the soy lecithin. (author)

  9. Radiation response of Philippine natural rubber latex

    International Nuclear Information System (INIS)

    Dela Rosa, A.M.; Abad, L.V.; Ana-Relleve, L.S.; Tranquilan-Aranilla, C.; Pascual, C.L.

    1998-01-01

    Our earlier work has shown that the natural rubber latex (NRL) produced and processed in the Philippines is suited for radiation vulcanization. The cast films from NRL with 50% TSC exhibited maximum tensile strengths of 25-32 MPa at 15 kGy, which is the vulcanization dose or Dv. In the manufacture of dipped NRL products, certain specifications such as %TSC, protein content and tensile properties, must be met to ensure an acceptable product. For radiation vulcanization of natural rubber latex (RVNRL) to be accepted as an alternative process, it must also meet the requirements. Thus, this paper presents additional data on the radiation response of local NRL at different total solids contents (TSC), leachable proteins from NRL films as a function of dose, and the thermal activities of irradiated natural rubber latex (INRL). Different formulations of NRL showed varying tolerances to nBA. Data showed that as %TSC increases, the maximum concentration of nBA that can be added without affecting the stability of the latex decreases. The Dv increases as the %TSC increases and the nBA content decreases. This difference in response may be attributed to a lower concentration of nBA in formulations with higher %TSC. These data indicate that the parameters in the radiation treatment will be dictated by the intended applications of INRL. The thermogravimetric data showed greater stability of INRL to thermal oxidation relative to the unirradiated NRL, which correlates directly with the tensile properties of the INRL. A radiation dose of 10 kGy increased the amount of proteins leached from cast latex films. The amount of extractable proteins did not increase significantly at higher doses. The SDS PAGE analysis of the extractable proteins from unirradiated latex film showed distinct bands. An additional band at 60 Kda appeared at 10 kGy. All these bands became diffuse at higher doses, indicating the radiolysis of the proteins

  10. Radiation vulcanization of Philippine natural rubber latex

    International Nuclear Information System (INIS)

    Dela Rosa, Alumanda M.; Abad, Lucille V.; Sta, Lorna P.; Ana-Relleve; Tranquilan-Aranilla, Charito O.; Pascual, Cristina L.

    1996-01-01

    The response of Philippine natural rubber latex to radiation vulcanization and the stability of the irradiated natural rubber latex (INRL) upon storage and aging were investigated. Commercially available high ammonia (HA) concentrated lattices obtained from various rubber plantations in Mindanao Island were treated with 5 phr of n-butyl acrylate (nBA), and gamma-irradiated at the PNRI sup 60 Co irradiation facility at dose rate of 2.57 KGy/hr. Unirradiated cast latex films gave different green strength which varied from 2 - 11 MPa. Cast films from INRL exhibited maximum tensile strengths of 25 - 32 MPa at a radiation dose of 15 kGy. Higher tensile strengths were obtained from cast films with low Mg and high nitrogen contents. Thermal analysis using thermogravimetry (TG) revealed one major decomposition product at 374 degree C - 377 degree C. Its rate of decomposition decreased to a minimum at 15 kGy, then increased as radiation dose increased. This trend correlated well with the tensile strength measurements. The stability of the INRL upon storage and aging is an essential parameter to the rubber latex industry. For storage studies, INRL was stored for various periods of time. It was found that the pH and total solids content of the stored INRL did not change significantly after 12 months of storage; the MST values remained at above 100 seconds, and the viscosity decreased with time. The cast films exhibited a decline in tensile strength, modulus 300% and crosslinking density upon storage. While there were observed changes in the physical properties of the IRNL during the storage period, the data indicate that these properties were within values acceptable to the latex industry. Tests on the aging properties of INRL film were undertaken. It was shown that among the chemical antioxidants presently used by the latex industry. TNPP demonstrated the highest antioxidant property, followed by Antage DAHQ and Vulcanox BKF. Our data indicate that the natural rubber latex

  11. Tensile properties of carbon black-filled natural rubber latex films using two different approaches of film preparation

    Science.gov (United States)

    Jarkasi, Siti Aisyah; Samsuri, Azemi; Hashim, M. Y. Amir; Kamarun, Dzaraini

    2017-09-01

    A study was structured to investigate the effects of two different approaches of black-filled NRL films preparation on tensile strengths and tensile stress at 100% strain (M100). In the "First Approach", carbon black dispersion was added into the NRL and mixed using mechanical stirrer. Then the black-filled NRL was coagulated with acetic acid and dried to form NR black-filled masterbatch. This black-filled NR masterbatch was then masticated and mixed with other compounding ingredients on the 2-roll mill. In the "Second Approach", carbon black dispersion was mixed with NRL plus all other compounding ingredients using a mechanical stirrer at high mechanical stirring speed (200 rpm) for 3 hrs. Tensile test-pieces from these two rubber specimens were tested according to ISO37. It was observed that the tensile strengths are affected by both methods. In the case of masticated latex masterbatch, the black-filled NRL films gave higher tensile strength (25-27 MPa) as compared to un-masticated black-filled NRL films (11-17 MPa). The optimum amount of filler loading for highest tensile strength in both approaches was 20 phr of carbon black. However these different approaches did not give significant effect to the elongation at break, EB and M100. SEM images of samples prepared from both approaches suggested that the dispersion of filler in the rubber matrix was better in the masticated samples compared to the un-masticated samples. The reason for the difference in the tensile strength between the two black-filled rubbers might be associated with the degree of dispersions and the uniformity of the dispersions within the rubber matrix. The first mixing approach involved high mechanical shearing action during mastication and mixing process on the 2-roll mill. The high shearing actions were able to breakdown filler aggregates efficiently and distributed the dispersed filler uniformly within the rubber matrix. In the second approach, the breakdown of filler aggregates relied on

  12. Cream concentrated latex for foam rubber products

    Science.gov (United States)

    Suksup, R.; Imkaew, C.; Smitthipong, W.

    2017-12-01

    Fresh natural latex (around 40% rubber and 60% water) can be transformed to concentrated natural latex (around 60% rubber and 40% water) in order to realise economical transportation and easier latex product’s preparation. The concentrated natural latex is an extremely valuable material. It can be applied for many types of products, for example, foam rubber as pillow and mattress, elastic band, etc. Industrially, the concentrated natural latex can be prepared by centrifugation which requires an enormous expensive machine. From the eco-friendly products point of view, most of rubber entrepreneurs in the world try to develop a green rubber product. So, the main objective of this study is to prepare the cream concentrated latex without any sophisticated machine. Thus, we work on a simple, cheap and green method that does not use any expensive machine but uses water-based chemical as sodium alginate to prepare the cream concentrated latex. The optimal amount of sodium alginate in the latex was studied. The main characteristics of the cream concentrated latex were tested by various technics, such as alkalinity, total solid content (TSC), dry rubber content (DRC), etc. We found that there are no significant differences of results between fresh natural latex and cream concentrated latex, except for the TSC and DRC. The TSC and DRC of cream latex are higher than those of fresh natural latex. Finally, we propose a model of natural rubber particle and sodium alginate to form the cream concentrated latex.

  13. Hevea brasiliensis natural rubber latex film vulcanization by gamma radiation containing n-butyl acrylate: properties and morphology; Filme de latex de borracha natural de Hevea brasiliensis vulcanizado por radiacao gama contendo acrilato de n-butila: propriedades e morfologia

    Energy Technology Data Exchange (ETDEWEB)

    Rodrigues, Ana Paula Pinho; Barros, Glaucione Gomes de [Brasilia Univ., DF (Brazil). Dept. de Quimica; Guedes, Selma M.L. [Instituto de Pesquisas Energeticas e Nucleares (IPEN), Sao Paulo, SP (Brazil)

    1997-07-01

    Radiation vulcanization of natural rubber latex (RVNRL) in the presence of n-butyl acrylate (n-Ba) as sensitizer was carried out. The RVNRL films were investigated with respect to their thermal properties and morphology. The films presented two T{sub g} values obtained by DSC which were identified as due to linear and crosslinked domains. The thermal stability of the material was similar to that of linear material rubber. The morphology showed smooth regular surface characteristic of homogeneous phase domains. (author)

  14. Toxicological evaluation of natural rubber films from vulcanized latex by the conventional process and the alternative process with ionizing radiation

    International Nuclear Information System (INIS)

    Campos, Vania Elisabeth

    1997-01-01

    The industrial vulcanization of natural rubber latex (NRL) is made all over the world by conventional process using sulphur and heat but it can be made by an alternative process using ionizing radiation. In this research the NRL was tested by 13 physical, chemical and mechanical assays which showed its good quality. It was done a preliminary study of the toxicological properties of 4 natural rubber films obtained by casting process of NRL: one non vulcanized, other vulcanized by the conventional process and two vulcanized by the alternative process. In the alternative process the films were obtained by irradiation of NRL by gamma rays from the 60 Co source at 250 kGy in the absence of sensitizer and irradiated NRL at 12 kGy in the presence of 4ph r of n-butyl acrylate / 0.2 phr of KOH. These vulcanization doses were determined from broken tensile strength. In the conventional process, sulphur vulcanized NRL was made using a classical composition. Another film was made with non vulcanized NRL. The preliminary evaluation of the toxicological properties was made from in vitro cytotoxicity and in vivo systemic toxicity assays. The LBN films vulcanized by the alternative process have less cytotoxicity than the NRL film vulcanized by the conventional process. The sensitized vulcanized films by gamma rays and non vulcanized films showed similar cytotoxicity while the vulcanized films without sensitizer showed a slight lower cytotoxicity. The non vulcanized NRL film and the NRL films vulcanized by the alternative process did not show toxic effects int he 72 hours period of the systemic toxicity assay. However the NRL film vulcanized with sulphur induced effects like allaying and motor in coordination on the animals treated with an oil extract at the fourth hour and recovering after that. The alternative process promoted lower toxic effects than conventional process because there was no toxic substances present. (author)

  15. Radiation vulcanization of natural rubber latex

    International Nuclear Information System (INIS)

    Wan Manshol bin Wan Zin; Norjanah binti Mohid

    1994-01-01

    This paper describes the experimental techniques and the results of radiation vulcanization of natural rubber latex carried out on several high ammonia latices available in the country. The efficiency of various sensitisers and stabilisers used were evaluated in terms of the gamma radiation dose required to produce the maximum tensile strengths. The extent of crosslinking of RVNRL sample films were estimated by equilibrium swelling ratio measurements. The stability of pre-irradiated and post-irradiated samples were monitored using viscosity measurements as the parameter

  16. Radiation vulcanization of natural rubber latex using irradiation n-butyl acrylate aqueous emulsion as sensitizer

    International Nuclear Information System (INIS)

    Vo Van Thien; Nguyen Quoc Hien; Keizo Makuuchi; Fumio Yoshii

    2000-01-01

    Natural rubber latex was vulcanized by gamma radiation with n-butyl acrylate aqueous emulsion irradiated at dose of 1.5 kGy as sensitizer. The total solid content of latex increases on the irradiation dose. The viscosity of latex on the standing time was investigated and became stable after one month of storage. The gel content of latex films increasing with irradiation dose and attained more than 94% at dose of 10 kGy. Tensile strength of films reached the values of 31MPa; 30 Mpa and 25 Mpa at vulcanization doses of 20 kGy, 15 kGy and 8 kGy for the concentrations of sensitizer 7 phr, 9 phr and 13 phr respectively. Elongation at break decreases as increasing dose. Tear strength of rubber films was from 30-40 N/mm. The tackiness of latex films decreases and smell of vulcanized latex is almost negligible. (author)

  17. NMR relaxation times of natural rubber latex

    International Nuclear Information System (INIS)

    Harun, S.; Aziz, H.; Basir, Z.

    1994-01-01

    NMR relaxation times T sub 1 and T sub 2 of natural rubber latex have been measured at 25 degree C on a pulsed NMR spectrometer. The work focuses on the variation of the relaxation times with the amount of water content from 0% to 50%. The water content was adjusted by centrifuging and removing a certain amount of water from the sample. The data were analysed using a biexponential fitting procedure which yields simultaneously either T sub 1a and T sub 1b or T sub 2a and T sub 2b. The amount of solid was compared with the known amount of dry rubber content

  18. Preparation of irradiated natural rubber latex-styrene copolymer for electrical gloves

    International Nuclear Information System (INIS)

    Made Sumarti Kardha

    2010-01-01

    Research on irradiated natural rubber latex-styrene copolymer to prepare electrical glove have been done. Vulcanization of natural rubber latex (NRL) was done by mixing 2 phr (per hundred of rubber) of normal butyl acrylate (n-BA) emulsion then irradiated with ã-ray "6"0Co at the dose of 30 kGy producing irradiated natural rubber latex (INRL). Natural rubber latex-styrene copolymers (SC) were prepared by mixing NRL and styrene monomer at styrene concentrations of 50 phr, 75 phr, 100 phr, 500 phr and irradiated at the doses of 15 kGy, 30 kGy and 45 kGy, then characterized their latex and film properties to obtain optimum SC of SC50. This optimum SC, SC50 then mixed with IRNL at the weight ratio of 0/100, 30/70, 50/50, 70/30 and 100/0, to produce irradiated natural rubber latex-styrene copolymer. The properties of copolymer rubber films made by dipping process i.e., % conversion, total solid content, latex viscosity, tensile strength, modulus 300 %, elongation at break, electrical resistance and dielectric constant were then characterized. Characterization result showed that (INRL-SC50) with 50/50 ratio irradiated at the dose of 30 kGy, have % conversion of 80.93 %, electrical resistivity of 1.73 x 10"1"4 Ohm cm and dielectric constant of 2.76 which fulfill the requirement as material for electrical gloves. (author)

  19. Biodegradability and aging study of rubber films obtained by gamma radiation vulcanization processes of latex; Estudo da biodegradabilidade e envelhecimento de filmes de borracha obtidos por processos de vulcanizacao do latex por radiacao induzida de fonte gama

    Energy Technology Data Exchange (ETDEWEB)

    Martins, Carlos Felipe Pinto

    2005-07-01

    The natural rubber latex (NRL) is industrially crosslinked by the conventional process of vulcanization, which uses sulphur and heat. Otherwise, the network can also be done by the alternative process with ionizing radiation. In this work the crosslinking of NRL was studied by the comparison of the conventional vulcanization system and the ionizing radiation process of {sup 60}C source. The products obtained, the irradiated latex, the irradiated latex with approximately 1% of soy lecithin and the sulphur vulcanized latex were tested by accelerated aging with ultraviolet (UV) and outdoor aging with compostage, tensile strength at break, swelling and gel fraction, fungi micro biota, scanning electron microscopy (SEM), infrared spectroscopy (FTIR) and thermogravimetry and differential scanning calorimetry analysis (TG and DSC). The results showed that the aging with microorganisms have a great influence in the physical properties of the samples. The thermal stability order observed showed that the sulphur vulcanized latex is more resistant, what is probably associated to a network more stable under the aging conditions. On the other hand, the irradiated latex showed intense biodegradation aspects, particularly with the presence of the soy lecithin. (author)

  20. Allergenicity of latex rubber products used in South African dental ...

    African Journals Online (AJOL)

    Fourteen latex examination gloves (powdered and non-powdered) and five dental rubber dams, representing 6 brands, from five dental academic institutions were analysed for latex allergens and total protein. Total protein content was determined using the BioRad DC protein assay kit and natural rubber allergen levels ...

  1. Test trial radiation vulcanization of natural rubber latex in Jakarta Indonesia

    International Nuclear Information System (INIS)

    Devendra, R.; Kulatunge, S.S.; Chandralal, H.N.K.K.; Kalyani, N.M.V.; Seneviratne, J.; Wellage, S.

    1994-01-01

    Radiation vulcanization of natural rubber latex (RVNRL) can be used to make large quantities of specially stabilized latex. It is possible to obtain RVNRL films of tensile strength over 25 MPa. The films could be either coagulant dipped or cast. It is very important to determine the correct radiation dose which gives the maximum tensile strength. Cross linking density or prevulcanized relax modulus (PRM) at 100% is a reliable property to control the prevulcanization

  2. Radiation vulcanization of natural rubber latex sensitized with commercial gases

    Energy Technology Data Exchange (ETDEWEB)

    Chirinos, H.; Lugao, A. [Instituto de Pesquisas Energeticas e Nucleares (IPEN), Sao Paulo, SP (Brazil)

    2002-07-01

    The industrial activities using natural rubber latex are fully compatible with rural areas in Amazon and other places in Brazil, as well as in other tropical countries. However the classical sulfur vulcanization presents many occupational problems for the workers in rural areas. Radiation vulcanization of natural rubber latex is a much more friendly process as sulfur compounds are not needed for crosslinking, although chemicals as acrylate monomers, particularly multifunctional acrylates are still used as sensitizers for radiation processes. Two commercial gases, acetylene and butadiene, were selected as sensitizers for the radiation vulcanization of natural rubber latex instead of acrylates. These gases accelerate the crosslinking rates of the cure process and lower the radiation dose required to achieve vulcanization of natural rubber latex and improve the mechanical properties to reduce the tackiness of rubber goods. (author)

  3. Radiation vulcanization of natural rubber latex sensitized with commercial gases

    International Nuclear Information System (INIS)

    Chirinos, H.; Lugao, A.

    2002-01-01

    The industrial activities using natural rubber latex are fully compatible with rural areas in Amazon and other places in Brazil, as well as in other tropical countries. However the classical sulfur vulcanization presents many occupational problems for the workers in rural areas. Radiation vulcanization of natural rubber latex is a much more friendly process as sulfur compounds are not needed for crosslinking, although chemicals as acrylate monomers, particularly multifunctional acrylates are still used as sensitizers for radiation processes. Two commercial gases, acetylene and butadiene, were selected as sensitizers for the radiation vulcanization of natural rubber latex instead of acrylates. These gases accelerate the crosslinking rates of the cure process and lower the radiation dose required to achieve vulcanization of natural rubber latex and improve the mechanical properties to reduce the tackiness of rubber goods. (author)

  4. Thermal-kinetic study of natural rubber latex films vulcanized by using gamma radiation; Estudo termo-cinetico de filmes de latex de borracha natural de Hevea brasiliensis vulcanizada por radiacao gama

    Energy Technology Data Exchange (ETDEWEB)

    Leal, Ana Paula Pinho Rodrigues; Barros, Glaucione Gomes de [Brasilia Univ., DF (Brazil). Inst. de Quimica; Guedes, Selma M.L. [Instituto de Pesquisa em Energia Nuclear, Sao Paulo, SP (Brazil)

    1999-07-01

    Vulcanization of natural rubber latex by ionization radiation produces the crosslink in disperse latex particles. Advantages over conventional process of vulcanization are: the absence of carcinogenic nitrosamines, low cytotoxicity and better degradation at room conditions, due to mainly to the absence of sulfur, zinc oxide and dithiocarbamates. Thermogravimetric analysis (TG) is the measurement of the weight change of a material as a function of temperature and time. TG data different heat speed provide an alternative model of the kinetics of degradation of polymeric materials. The kinetic studies of this material showed a single degradation process at least for 76,5% of mass loss. The activation energy was 49 Kcal/mol. For higher mass loss (85%) the degradation was characterized by associate mechanism. (author)

  5. Preparation of highly stabilised natural rubber latex for radiation vulcanisation

    International Nuclear Information System (INIS)

    Kulatunge, S.S.; Nadarajah, M.; Kalyani, N.M.V.; Chandralal, H.N.K.K.; Devendra, R.

    1996-01-01

    There is a bright future for radiation vulcanised natural rubber latex (RVNRL) but there are problems in manufacturing it as the centrifuged latex to be used for radiation has to be kept for at least a month or sometimes even three to six months before adding the sensitisers and even then the latex sometimes coagulates on adding the sensitisers. This paper describes a process by which the latex can be stabilised by addition of an anionic soap before centrifuging so that it has a high mechanical stability and hence can be used even within one week of the manufacture of the centrifuged latex

  6. The effect of proteins on the aging properties of radiation vulcanized natural rubber latex

    International Nuclear Information System (INIS)

    Abad, L.V.

    1993-01-01

    The effect of natural rubber latex (NRL) proteins on the aging properties of NRL films was investigated. SDS-PAGE electrophoresis of the rubber proteins in NRL (Sri-Lanka) indicated a total of 18 proteins. A sharp decrease in tensile strength was observed after aging when NRL films were leached in 1% NH 4 OH. However, when these films were soaked in ethanol prior to leaching, the aging properties approximated those of the unleashed samples. Electrophoretic analysis of the proteins present in the NH 3 extracts of leached RVNRL films showed a high concentration of the protein herein. This protein was not found in the NH 3 extracts of ethanol soaked films. NRL proteins were shown to decelerate the aging process of Radiation Vulcanized Natural Rubber Latex (RVNRL) films. Among the proteins, herein exhibited good anti-aging properties. The hydrolyzates from NR proteins also enhanced considerably the aging properties of RVNRL. (auth.). 8 refs.; 40 figs.; 30 tabs

  7. Trialed production of low protein irradiated natural rubber latex in factory scale by gamma irradiation technique

    International Nuclear Information System (INIS)

    Utama, Marga; Herwinarni, S.; Halik, H.M.; Siswanto; Suharyanto; Syamsu, Y.; Handoko, B.

    2006-01-01

    Four tons fresh field natural rubber latex (FNRL) with total solid content 30% were added with 2 phr (part hundred ratio of rubber) normal butyl acrylate (nBA) then irradiated by gamma rays at 25 kGy. The irradiated FNRL was centrifuged, then the properties of irradiated centrifuged natural rubber latex (INRL) and its film were measured before and after storage for 5 months. It is found that the INRL is stable latex during storage in 5 months, with lowest protein, and free nitrosamine content. The tensile strength of INRL film was 24-27 MPa, and modulus 600% was 1,5-2,0 MPa, elongation at break was 900%, and hardness was 27-29 Shore A, while the extractable protein content less than 100 μg/g. (author)

  8. High concentrations of natural rubber latex allergens in gloves used ...

    African Journals Online (AJOL)

    Introduction. Gloves made of natural rubber latex (NRL) are commonly used by healthcare workers because of their good qualities. However, allergic reactions to latex allergens are still commonly reported. Objective. To measure the concentrations of Hev b 1, Hev b 3, Hev b 5 and Hev b 6.02 allergens in gloves used by a ...

  9. Extractable proteins from electron beam (EB) irradiated natural rubber (NR) latex

    International Nuclear Information System (INIS)

    Feroza Akhtar; Fumio Yoshii; Keizo Makuuchi

    1996-01-01

    The protein assay of natural rubber latex (NRL) vulcanized by low energy electron beam (EB, 300 keV, 30 mA) has been carried out using Bicinchoninic acid (BCA) reagent. Extractable protein in irradiated latex film was determined by measuring the absorption of colored solution at 562 nm using UV spectrometer. The effect of various radiation doses on the extractable protein content of NRL was investigated. It was ,found that the quantities of extractable protein increases with radiation dose. When compared with ,gamma-ray irradiated samples the same trend was observed. Electron beam irradiated latex films are leached in 1% (ammonia water for various lengths of time. From the results it was established that within 2 hours of leaching in ammonia water most of the extractable protein (96%) were removed from rubber film

  10. Exploiting epoxidized natural rubber latex (ENRL) as a starting raw material for latex-based products

    Science.gov (United States)

    Siti Nor Qamarina, M.; Fatimah Rubaizah, M. R.; Nurul Suhaira, A.; Norhanifah, M. Y.

    2017-12-01

    Epoxidized natural rubber latex (ENRL) is a chemically modified natural rubber latex produced from epoxidation process that involves usage of organic peracids. Conversion of the ENRL into dry rubber products has been known to exhibit many beneficial properties, however limited published works were found on diversifiying the ENRL latex-based products applications. In this preliminary work, different source of raw materials and neutralization systems were investigated. The objective was to explore possibilities in producing distinctive ENRL. Findings have demonstrated that different source of raw materials and neutralization systems influenced the typical ENRL specifications, stability behavior and particle size distribution. Morphological observations performed on these ENRL systems appeared to agree with the ENRL characteristics achieved. Since experimenting these two main factors resulted in encouraging ENRL findings, detailed work shall be further scrutinized to search for an optimum condition in producing marketable ENRL specifically for latex-based products applications.

  11. Extraction and comparison of proteins from natural rubber latex by conventional and ionizing radiation methods

    International Nuclear Information System (INIS)

    Rogero, Sizue O.; Spencer, Patrick J.; Campos, Vania E.; Lusvarghi, Fabio M.; Higa, Olga Z.

    1997-01-01

    Several proteins in natural rubber latex (NRL) have been assigned to be significant allergens. It is known that proteins submitted to ionizing radiation suffer denaturation and immunochemical modification resulting in low antigenic reactivity. The aim of this study was to extract and compare water extractable proteins from NRL films vulcanized by conventional and by ionizing radiation methods. SDS-polyacrylamide gel electrophoresis (SDS--PAGE) and high pressure liquid chromatography (HPLC) showed a diffuse protein band of about 14 KDa, which we believe is rubber elongation factor (REF), in both eluates, but smaller in latex film vulcanized by ionizing radiation. REF has been suggested to be a major latex allergen. These data suggest that ionizing radiation vulcanization could be an useful method for the production of NRL goods with low antigenicity. (author). 8 refs., 2 figs., 1 tab

  12. The role of proteins on the thermal oxidative aging of radiation vulcanized natural rubber latex

    International Nuclear Information System (INIS)

    Abad, L.V.; Rosa, A. de la; Keizo Makuuchi; Fumio Yoshii

    1996-01-01

    The effect of Hevea latex proteins on the aging properties of radiation vulcanized natural rubber latex (RVNRL) was investigated. Unpurified RVNRL films exhibited better aging properties than the purified RVNRL films. A sharp decrease in tensile strength was observed after aging when RVNRL films were leached in 1% NH sub 4 OH. However, when these films were soaked in ethanol prior to leaching, the aging properties approximated those of the unleached samples. Kjeldahl and FT-IR analyses of the leached and unleached RVNRL films indicated a higher protein content for both the unleached and ethanol-soaked films than for leached films. Electrophoretic analysis of the proteins present in the NH, extracts of leached RVNRL films showed a high concentration of hevein. This protein was not found in the ATH, extracts of ethanol soaked films. Hevein was shown to improve the aging properties of RVNRL

  13. Radiation vulcanization of natural rubber latex with low energy accelerator

    Energy Technology Data Exchange (ETDEWEB)

    Haque, Emdadul; Makuuchi, Keizo; Ikeda, Kenichi; Yoshii, Fumio; Kume Tamikazu [Japan Atomic Energy Research Inst., Takasaki, Gunma (Japan). Takasaki Radiation Chemistry Research Establishment; Mitomo, Hiroshi [Gunma Univ., Faculty of Engineering, Department of Biological and Chemical Engineering, Kiryu, Gunma (Japan)

    2001-03-01

    The radiation vulcanization of natural rubber latex (RVNRL) with the recently installed electron beam (EB) pilot plant at Takasaki Radiation Chemistry Research Establishment, Takasaki, Japan has been discussed. The accelerating voltage and beam current of the plant are 250 kV and 10 mA respectively. The plant has a reaction vessel with the capacity of 18 liters latex to irradiate at a time. In order to obtain a suitable setting of experimental for RVNRL under EB of the plant the parameters such as irradiation time, defoamer concentration, volume of latex, beam current etc. are being optimized by varying the individual parameter at a constant set of the other variables. (author)

  14. Radiation Vulcanization of Natural Rubber Latex (RVNRL): A Potential Material for Nuclear Power Plant Gloves

    International Nuclear Information System (INIS)

    Pairu Ibrahim; Wan Manshol Wan Zain; Keong, C.C.; Mohd Noorwadi Mat Lazim

    2011-01-01

    Radiation vulcanization of natural rubber latex has great potential for the production of nuclear power plant gloves due to its low ash and mineral content. And this is in-line with the role played by Malaysian Nuclear Agency as Technical Supporting Organization for Nuclear Power Program. This paper discussed the evaluation done to determine ash content in RVNRL and SVNRL films. Both samples were prepared using casting technique and the properties were compared. Films prepared from raw latex without any vulcanizing agent were regarded as a control. (author)

  15. Marine bacterial prodigiosin as dye for rubber latex, polymethyl ...

    African Journals Online (AJOL)

    Prodigiosin is known for its immunomodulatory, antibacterial, antimycotic, antimalarial, algicidal and anticancer activities. Here, we reported the evaluation of prodigiosin pigment as a dyeing agent in rubber latex, paper and polymethyl methacrylate (PMMA) so that it can be considered as an alternative to synthetic pigments.

  16. Application of radiation vulcanized natural rubber latex in Indonesia

    International Nuclear Information System (INIS)

    Soebianto, Y.S.; Wiwik Sofiarti; Razzak, M.T.

    1996-01-01

    The center has carried out R and D of Radiation Vulcanization Natural Rubber Latex (RVNRL) technology and introduced it to the industries since the inauguration and operation of the latex pilot plant in 1983. After years of experiences and the environmental consideration, n-butylacrylate (n-BA) has replaced CCI, as the sensitizer. Until now the introduction program shows that radiation vulcanized latex is more suitable for home industries than large industries. The obstacle of the program is the marketing of the dipped products. In spite of these problems, the introduction of this technology to the people in some undeveloped area of Java has supported the national program to improve their living standard. The problems of nitrosamine and protein allergic have turn up RVNRL to be the substitute of sulfur vulcanized latex in the future. The cooperation with a national condom manufacturer (PT Mitra Banjaran) has applied RVNRL for condom production in the large scale. Soft condoms with less probability of pinhole are obtained, but the technical problem is stickiness after pilling. Supply to a baby teat and a rubber thread manufacturer offers great advantages by not using any chemicals. In spite of the advantages, the problem of latex viscosity for dipping and the low modulus of elasticity of the threads arise. Through those input CAIR-BATAN is conducting the research and development in improving the crosslinking among the rubber particles that are supposed to be the reason of the stickiness and low modulus of elasticity. This effort is expected to be able to broaden the application of RVNRL, and it will be achieved only by the involvement of rubber chemist, rubber technologist, and radiation chemist

  17. Toxicological evaluation of natural rubber films from vulcanized latex by the conventional process and the alternative process with ionizing radiation; Avaliacao toxicologica de filmes de borracha natural obtidos do latex vulcanizado pelo processo convencional e pelo processo alternativo com radiacao ionizante

    Energy Technology Data Exchange (ETDEWEB)

    Campos, Vania Elisabeth

    1997-07-01

    The industrial vulcanization of natural rubber latex (NRL) is made all over the world by conventional process using sulphur and heat but it can be made by an alternative process using ionizing radiation. In this research the NRL was tested by 13 physical, chemical and mechanical assays which showed its good quality. It was done a preliminary study of the toxicological properties of 4 natural rubber films obtained by casting process of NRL: one non vulcanized, other vulcanized by the conventional process and two vulcanized by the alternative process. In the alternative process the films were obtained by irradiation of NRL by gamma rays from the {sup 60} Co source at 250 kGy in the absence of sensitizer and irradiated NRL at 12 kGy in the presence of 4ph r of n-butyl acrylate / 0.2 phr of KOH. These vulcanization doses were determined from broken tensile strength. In the conventional process, sulphur vulcanized NRL was made using a classical composition. Another film was made with non vulcanized NRL. The preliminary evaluation of the toxicological properties was made from in vitro cytotoxicity and in vivo systemic toxicity assays. The LBN films vulcanized by the alternative process have less cytotoxicity than the NRL film vulcanized by the conventional process. The sensitized vulcanized films by gamma rays and non vulcanized films showed similar cytotoxicity while the vulcanized films without sensitizer showed a slight lower cytotoxicity. The non vulcanized NRL film and the NRL films vulcanized by the alternative process did not show toxic effects in the 72 hours period of the systemic toxicity assay. However the NRL film vulcanized with sulphur induced effects like allaying and motor in coordination on the animals treated with an oil extract at the fourth hour and recovering after that. The alternative process promoted lower toxic effects than conventional process because there was no toxic substances present. (author)

  18. Radiation vulcanised natural rubber latex (RVNRL) market and challenges

    International Nuclear Information System (INIS)

    Wan Manshol Wan Zin; Najib Mohamad Zakey; Chai Chee Keong

    2000-01-01

    RVNRL has the required properties and proven useful for the manufacturing of examination gloves, balloons and finger cots at industrial scale. To date only RVNRL finger cots are available in the market. Problems and challenges for the market of other products are identified. Further success in the on going research activities will be the reference for more applications of RVNRL in the relevant industry to produce natural rubber latex products of more competitive values

  19. Natural rubber latex: determination and interpretation of flow curves

    Directory of Open Access Journals (Sweden)

    Harrison Lourenço Corrêa

    2015-08-01

    Full Text Available AbstractAs consumers become more demanding, the importance grows of guaranteeing the quality of products. The employment of reliable testing techniques that assure the origin and characteristics of the inputs used by industry is a key factor in this respect. In the rubber processing industry, the most commonly used characterization tests include determination of the total solids and dry rubber content, mechanical stability, odor, color and presence of volatile compounds, among others. For the most part, these tests are sufficient for the latex transformation industry. However, in situations where there is a need to know the behavior of latex in reaction to the mechanical forces of machines (mixers, pumps, etc., other tests must be used. Rheological tests to determine viscoelastic data by means of plotting flow curves combined with the application of theoretical models can provide important details for characterization of different types of latex. This article presents the protocol employed by the Rheology and Image Laboratory of Rio de Janeiro State University (UERJ for the rheological study of Brazilian latex. The samples analyzed came from the state of São Paulo.

  20. Progress in radiation vulcanization of natural rubber latex

    International Nuclear Information System (INIS)

    Makuuchi, Keizo

    2000-01-01

    Vulcanization dose defined as the radiation dose at which cross-linked natural rubber in latex has the maximum tensile strength can be reduced by adding carbon tetrachloride as a reaction accelerator. The radiation vulcanization of natural rubber latex was selected as one of regional projects of IAEA in 1989 and a pilot plant was built in Jakarta. The products from it were evaluated during 1983-1985, followed by IAEA decision to support the continued R and D study at Takasaki, JAERI. Various factors to improve the properties of the products have been studied. Several advantages of the process over conventional method, such as absence of N-nitrosoamines, low cytotoxicity, decomposability in the environment, transparency and softness, were confirmed. The technology has been transferred toward commercial application in Thailand, and pilot plants being set up in Indonesia, India, Malaysia and Thailand. Moreover, the process was found to be effective in reducing protein remaining in natural rubber latex products and the initial investment and irradiation cost was found to be greatly reduced by employing low energy electron accelerator. This paper reviews such progress. (S. Ohno)

  1. Extractable proteins from field radiation vulcanized natural rubber latex

    Energy Technology Data Exchange (ETDEWEB)

    Parra, Duclerc F. [Chemical and Environmental Centre, Nuclear Energy Research Institute, Av. Lineu Prestes, 2242-CEP Sao Paulo (Brazil)]. E-mail: dfparra@ipen.br; Pinto Martins, Carlos Felipe [Chemical and Environmental Centre, Nuclear Energy Research Institute, Av. Lineu Prestes, 2242-CEP Sao Paulo (Brazil); Collantes, Hugo D.C. [Chemical and Environmental Centre, Nuclear Energy Research Institute, Av. Lineu Prestes, 2242-CEP Sao Paulo (Brazil); Lugao, Ademar B. [Chemical and Environmental Centre, Nuclear Energy Research Institute, Av. Lineu Prestes, 2242-CEP Sao Paulo (Brazil)

    2005-07-01

    The type I allergy associated with the use of natural rubber latex (NRL) products is caused by the NRL proteins leached by the sweat or other body fluids. Makuuchi's group proposed for the first time the proteins removal by the addition of water-soluble polymers (WSP) on radiation vulcanization of natural rubber latex (RVNRL) that is a promising process under development in many countries. In this study, Brazilian field natural rubber was irradiated with a {sup 60}Co gamma source to reduce the content of WSP in the final product. WSP was used as additive to improve the extraction of protein. After irradiation the RVNRL was centrifuged to extract the WSP and proteins. The analytical methodology for protein content was based on the modified Lowry method according to ASTM D5712. Protein determination was carried out in serum of latex and in the extracts of the gloves. The concentration of extractable water-soluble proteins in serum of irradiated field NRL (NRL1), not irradiated one (NRL2); of twice centrifuged sample with polymer additive NRL (NRL3) and of the glove manufactured (NRLG) are compared with commercial glove (CG). The irradiation process increases the extractable water-soluble proteins, EP, as reported in the literature. In this study the use of polymeric additive on the bi-centrifugation process to remove protein was successful and the EP of the glove obtained in NRL3 was at around 40% of the commercial glove.

  2. Radiation prevulcanized natural rubber latex: Cytotoxicity and safety evaluation on animal

    Energy Technology Data Exchange (ETDEWEB)

    Keong, C C; Zin, W M Wan; Ibrahim, P; Ibrahim, S, E-mail: chai@nuclearmalaysia.gov.my [Malaysian Nuclear Agency, Bangi, 43000 Kajang, Selangor (Malaysia)

    2010-05-15

    Radiation prevulcanized natural rubber latex (RVNRL) was claimed to be more user friendly than natural rubber latex prevulcanized by sulphur curing system. The absence of Type IV allergy inducing chemicals in RVNRL make it a suitable material for manufacturing of many kinds of latex products, especially those come into direct contact with users. This paper reveals and discusses the findings of cytotoxicity test and safety evaluation on animal for RVNRL. The test was done on RVNRL films prepared by coagulant dipping method and RVNRL dipped products produced by latex dipped product manufacturers. Cytotocixity test was carried out on mammalian cell culture American Type Culture Collection CCL 81, Vero. Results indicated that no cytotoxic effect from RVNRL films and products was found on the cell culture. Two animal studies, namely dermal sensitization study and primary skin irritation study, were done on gloves made from RVNRL. Albino white guinea pigs were used as test subjects in dermal sensitization study and results showed no sensitization induced by the application of test material in the guinea pigs. Primary skin irritation study was done on New Zealand white rabbits and results showed that the product tested was not corrosive and was not a primary irritant

  3. Radiation prevulcanized natural rubber latex: Cytotoxicity and safety evaluation on animal

    International Nuclear Information System (INIS)

    Keong, C C; Zin, W M Wan; Ibrahim, P; Ibrahim, S

    2010-01-01

    Radiation prevulcanized natural rubber latex (RVNRL) was claimed to be more user friendly than natural rubber latex prevulcanized by sulphur curing system. The absence of Type IV allergy inducing chemicals in RVNRL make it a suitable material for manufacturing of many kinds of latex products, especially those come into direct contact with users. This paper reveals and discusses the findings of cytotoxicity test and safety evaluation on animal for RVNRL. The test was done on RVNRL films prepared by coagulant dipping method and RVNRL dipped products produced by latex dipped product manufacturers. Cytotocixity test was carried out on mammalian cell culture American Type Culture Collection CCL 81, Vero. Results indicated that no cytotoxic effect from RVNRL films and products was found on the cell culture. Two animal studies, namely dermal sensitization study and primary skin irritation study, were done on gloves made from RVNRL. Albino white guinea pigs were used as test subjects in dermal sensitization study and results showed no sensitization induced by the application of test material in the guinea pigs. Primary skin irritation study was done on New Zealand white rabbits and results showed that the product tested was not corrosive and was not a primary irritant

  4. Extractable protein of radiation vulcanized natural rubber latex

    International Nuclear Information System (INIS)

    Soebianto, Y.S.; Ratnayake, U.M.; Makuuchi, Keizo; Yoshii, Fumio; Kume, Tamikazu

    2000-01-01

    Protein remained in the latex products are reported to cause serious allergy. A new method to reduce the protein level in the latex products by irradiation is reported. Water soluble protein (WSP) solution (10%) was added into radiation vulcanized NR latex (RVNRL) in three different processes. The amount of WSP was 3 phr. It was only added to RVNRL (standard), added to re-centrifuged RVNRL (pre-centrifugation), and added to RVNRL followed by centrifugation (post-centrifugation). The protein content was determined by enhanced BCA method, and identified by SDS-PAGE. Extractable protein (EP) from the rubber has been reduced up to the minimum protein detection by combining WSP addition and centrifugation. Short leaching time (20-30 min.) can be achieved after the combine treatment, and SDS-PAGE confirms the reduction of soluble protein in the serum phase, and disappearance of protein bands in the rubber extract. Protein-WSP interaction produces water soluble complex, and removed by centrifugation. The efficiency of protein removal by WSP depends on its molecular weight of WSP which relates to its water solubility. (author)

  5. Safety Evaluation Test on Human for Radiation Pre vulcanised Natural Rubber Latex (RVNRL)

    International Nuclear Information System (INIS)

    Pairu Ibrahim; Wan Manshol Wan Zain; Chai, Chee Keong; Sofian Ibrahim; Saadiah Sulaiman; Sharifah Ismail

    2010-01-01

    This paper discussed about clinical test conducted to determine safety evaluations on human for latex examination gloves and latex films made from Radiation Vulcanized Natural Rubber Latex (RVNRL). Two types of test were being adopted which are i) Modified Draize-95 test and ii) Patch Test on Sensitized Individuals. Modified Draize-95 test was conducted on 200 non-sensitized human subjects and Patch Test on Sensitized Individuals was conducted on 25 individuals who are allergic to the defined major chemical sensitizer presents in natural rubber product. It was found that Modified Draize-95 test has prove that there is no clinical evidence on the presence of residual chemical additives at the level that may induce Type IV allergy in the un sensitized general user population in the RVNRL gloves. Meanwhile Patch Test on Sensitized Individuals has proved that the patch test conducted using the test article on 25 individuals who are allergic to the defined major chemical sensitizers present in natural rubber products, thiuram, carbamates or thiazoles produced a negative response, meeting the pre requirement for the claim of reduced reaction-inducing potential. (author)

  6. Maillard Reaction in Natural Rubber Latex: Characterization and Physical Properties of Solid Natural Rubber

    Directory of Open Access Journals (Sweden)

    S. Montha

    2016-01-01

    Full Text Available Maillard reaction in Natural Rubber (NR latex was investigated by treating fresh NR latex with glutaraldehyde (C5H8O2 in amounts of 0, 50, 100, and 200 mmol/kg of latex. Protein cross-linking in fresh NR latex and solid NR was confirmed by using sodium dodecylsulfate polyacrylamide gel electrophoresis (SDS-PAGE and attenuated total reflection infrared (ATR-IR spectroscopy, respectively. It was found that degree of protein cross-linking in NR increased with increasing C5H8O2 concentration. Physical properties of untreated and treated NR substances in terms of gel content, initial Wallace plasticity (P0, plasticity retention index (PRI, Mooney viscosity, and tensile strength were carefully explored. Results clearly showed that the Maillard cross-linking of proteins had remarkable effect on bulk NR properties, that is, solvent resistance, hardness, resistance to oxidation, rheological behavior, and resistance to stretching out.

  7. Physical-biopolymer characterization of polyhydroxybutyrate-co-hydroxyvalerate (PHBV) blended with natural rubber latex

    Energy Technology Data Exchange (ETDEWEB)

    Kuntanoo, K., E-mail: thip-kk@hotmail.com [Graduate School of Khon Kaen University, Khon Kaen, 40002 Thailand (Thailand); Promkotra, S., E-mail: sarunya@kku.ac.th [Department of Geotechnology, Faculty of Technology, Khon Kaen University, Khon Kaen 40002 Thailand (Thailand); Kaewkannetra, P., E-mail: paknar@kku.ac.th [Department of Biotechnology, Faculty of Technology, Khon Kaen University, Khon Kaen 40002 Thailand (Thailand)

    2015-03-30

    A biopolymer of polyhydroxybutyrate-co-hydroxyvalerate (PHBV) is blended with bio-based materials, natural rubber latex, to improve their microstructures. The various ratios between PHBV and natural rubber latex are examined to develop their mechanical properties. In general, physical properties of PHBV are hard, brittle and low flexible while natural rubber (NR) is presented itself as high elastic materials. Concentrations of the PHBV solution are constituted at 1%, 2% and 3% (w/v). The mixtures of their PHBV solutions to natural rubber latex are produced the blended films in three different ratios of 4:6, 5:5 and 6:4, respectively. They are characterized by appearance analyses which are the scanning electron microscope (SEM), universal testing machine (UTM) and differential scanning calorimetry (DSC). The SEM photomicrographs of the blended films and the controlled PHBV can provide the void distribution in the range of 12-14% and 19-21%, respectively. For mechanical properties of the blended films, the various elastic moduli of 1%, 2% and 3% (w/v) PHBV are the average of 773, 956 and 1,007 kPa, respectively. The tensile strengths of the blends increase with the increased concentrations of PHBV, similarly trend to the elastic modulus. The crystallization and melting behavior of unmixed PHBV and the blends are determined by DSC. Melting transition temperatures (T{sub m}) of the unmixed PHBV are stated two melting peak at 154°C and 173°C. Besides, the melting peaks of the blends alter in the range of 152-156°C and 168-171°C, respectively. According to morphology of the blends, the void distribution decreases twice compared to the unmixed PHBV. The results of mechanical properties and thermal analysis indicate that the blended PHBV can be developed their properties by more resilient and wide range of temperature than usual.

  8. Extractable protein of radiation vulcanized natural rubber latex

    International Nuclear Information System (INIS)

    Soebianto, Y.S.; Upul, R.M.; Makuuchi, K.; Yoshii, F.; Kume, T.

    2000-01-01

    A new method to reduce the protein level in the latex products by irradiation is reported. Water soluble protein (WSP) solution (10%) was added into radiation vulcanized NR latex (RVNRL) as much as 3 phr in three different processes: added to RVNRL, added to re-centrifuged RVNRL, and added to RVNRL followed by centrifugation. The protein content was determined by enhanced BCA method, and identified by SDS-PAGE analysis. Addition of WSP followed by centrifugation reduces EP up to the minimum protein detection, and shortens the leaching time to 20-30 min. SDS-PAGE analysis confirms the reduction of soluble protein in the serum phase, and disappearance of protein bands in the rubber extract. Protein-WSP interaction produces water soluble complex, and removed by centrifugation. The molecular weight of WSP dictates the efficiency of protein removal. (author)

  9. Extractable protein of radiation vulcanized natural rubber latex

    Energy Technology Data Exchange (ETDEWEB)

    Soebianto, Y.S. [Center for Research and Development of Isotopes and Radiation Technology, BATAN, Jakarta (Indonesia); Upul, R.M. [Rubber Research Institute of Sri Lanka, Ratmalana (Sri Lanka); Makuuchi, K.; Yoshii, F.; Kume, T. [Japan Atomic Energy Research Inst., Takasaki, Gunma (Japan). Takasaki Radiation Chemistry Research Establishment

    2000-03-01

    A new method to reduce the protein level in the latex products by irradiation is reported. Water soluble protein (WSP) solution (10%) was added into radiation vulcanized NR latex (RVNRL) as much as 3 phr in three different processes: added to RVNRL, added to re-centrifuged RVNRL, and added to RVNRL followed by centrifugation. The protein content was determined by enhanced BCA method, and identified by SDS-PAGE analysis. Addition of WSP followed by centrifugation reduces EP up to the minimum protein detection, and shortens the leaching time to 20-30 min. SDS-PAGE analysis confirms the reduction of soluble protein in the serum phase, and disappearance of protein bands in the rubber extract. Protein-WSP interaction produces water soluble complex, and removed by centrifugation. The molecular weight of WSP dictates the efficiency of protein removal. (author)

  10. Science and technology of rubber reclamation with special attention to NR based waste latex products

    NARCIS (Netherlands)

    Rajan, V.V.; Dierkes, Wilma K.; Joseph, R.; Noordermeer, Jacobus W.M.

    2006-01-01

    A comprehensive overview of reclamation of cured rubber with special emphasis on latex reclamation is depicted in this paper. The latex industry has expanded over the years to meet the world demands for gloves, condoms, latex thread, etc. Due to the strict specifications for the products and the

  11. Radiation vulcanization of natural rubber latex with low energy accelerator-II

    Energy Technology Data Exchange (ETDEWEB)

    Haque, Md. Emdadul; Makuuchi, Keizo; Ikeda, Kenichi; Yoshii, Fumio; Kume, Tamikazu [Japan Atomic Energy Research Inst., Takasaki, Gunma (Japan). Takasaki Radiation Chemistry Research Establishment; Mitomo, Hiroshi [Gunma Univ., Faculty of Engineering, Dept. of Biological and Chemical Engineering, Kiryu, Gunma (Japan)

    2002-03-01

    The natural rubber latex (NRL) was radiation vulcanized under a low energy electron accelerator. Accelerating voltage and maximum beam current of this accelerator are 250 kV and 10 mA respectively. Irradiation was carried out in a reaction vessel with constant stirring. The capacity of the vessel is 18 liters. Radiation vulcanization accelerators (RVA) were normal butyl acrylate (n-BA) and nonane-diol-diacrylate (NDDA). NDDA has no bad smell like that of n-BA. 20 minutes irradiation time is enough to vulcanize 14 liters of latex when 5 phr RVA (both types) are used. Maximum of {approx}30 MPa tensile strength was obtained with 5 phr NDD-A. However the remained NDDA is difficult to remove due to high molecular weight. Water-extractable proteins content was determined in dipped films for various leaching conditions without and with additive (polyvinyl alcohol, PVA). Water extractable proteins content is reduced to {<=} 41 by adding 5 phr PVA and leaching for 8 hours. The tackiness of the dipped films is reduced to 0.1 from 9 gf by mixing 6 phr PVA with the irradiated latex. Hand gloves (surgical and examination) were successfully produced from the irradiated latex. (author)

  12. Development of an efficient process for radiation vulcanization of natural rubber latex using hydroperoxide with sensitizer

    International Nuclear Information System (INIS)

    Siri-upathum, C.; Sonsuk, M.

    1996-01-01

    An attempt was made to reduce irradiation dose for radiation vulcanization of natural rubber latex. A promising method was to partially crosslink the latex by radiation vulcanization using n-butyl acrylate (n-BA) as sensitizer and t-butyl hydroperoxide (BHPO) as a co-sensitizer followed by redox vulcanization using residual BHPO as an oxidant and either fructose or tetra ethylene penta mine as reducing agents. It was found that the irradiation dose was reduced to 4 kGy with 5 phr n-BA as sensitizer and 0.1 phr BHPO as co-sensitizer. Successive crosslinking to full vulcanization was done by redox vulcanization using either 4 phr fructose at 60 degree C for 3 hours of 0.4 phr tetra-ethylene penta mine at room temperature for 1 hour. The rubber films obtained had tensile strength of about 25 MPa, modulus 300% of 0.9 MPa and crosslink density of about 1.5 x 10 19 crosslink/cm 3 . It was noted that the rubber film from the co-vulcanization was the average value of the values obtained by radiation vulcanization and redox vulcanization

  13. Natural rubber latex: past, present and future in Latin America

    International Nuclear Information System (INIS)

    Lugao, A.B.; Miranda, A.; Mindrisz, A.C.; Andrade e Silva, L.G. de

    1996-01-01

    The origin of the Hevea braziliensis tree was the Amazonian region in South America, particularly the Brazilian jungle. The rubber expansion at the end of 9th century brought prosperity and determined the borders of Amazonian countries. In spite of that, the Brazilian government has failed in establishing a successful policy for improving the NR production in the jungle. However, rubber plantations were successfully introduced recently near marginal areas of the humid forest in the Amazon due to the absence of the fungus Microcyclos ulei. Both, extraction of wild rubber and plantation have a key role in the maintenance of the forest health. The market for dipping products is small but is growing very fast and is expected to follow this pattern as the sanitary conditions are improved by the health authority. The history of the Brazilian NR products industry is contemporary and is based on the policy of market protection and on the lack of investments due to extremely high interest rates. As a result, the industry was not competitive. It was concluded that, in order to cope with the future challenge, the industry is required to invest in very modern technologies to produce first class goods with international acceptance. Latin America would follow the world trend for nitrosamine and protein free products. The radiation vulcanization of natural rubber latex could prove itself as a profitable solution and not only a quality solution. It was also concluded that both wild rubber and rubber plantations in Brazil have their future coupled with the future of a regional dipping industry. Moreover, the buildup of the dipping industry will be beneficial to the protection of the humid forest and the recovery of degraded areas

  14. Effect of gamma radiation dose and sensitizer on the physical properties of irradiated natural rubber latex

    International Nuclear Information System (INIS)

    Komgrit, R.; Thawat, C.; B, Tripob; Wirach, T.

    2009-07-01

    Full text: The vulcanization of natural rubber latex can be induced by gamma radiation, which enhances cross-linking within the rubber matrix. The purpose of this research is to investigate the effect of gamma radiation dose and sensitizers on the physical properties of irradiated natural rubber. Three sensitizers n-butyl acrylate (n-B A), tetrachloroethylene (C 2 Cl 4 ) and trichloromethane (CHCl 3 ) were mixed with natural rubber latex before irradiation with gamma ray dose varied from 14 to 22 kGy. Results showed that the mixture of three sensitizers with specific ratios effectively induced the cross-linking of natural rubber latex. The cross-linking ratio and improved physical properties increased with increasing gamma dose. Therefore, the mixture ratios of n-B A, C 2 Cl 4 and CHCl 3 have shown to be a critical parameter in the vulcanization of natural rubber latex by gamma radiation

  15. Study on grafting of monomer onto natural rubber latex by radiation technique

    International Nuclear Information System (INIS)

    Nguyen Tan Man; Le Hai; Tran Thi Tam; Le Huu Tu, Pham Thi Sam; Dao Minh Phuong; Ha Thuc Huy

    2004-01-01

    Radiation vulcanization of natural rubber latex has been extensively developed through programmers assisted by the IAEA and UNDP under RCA in Asia and Pacific Region. R-D has been done in most of the Member States with technical assistance from Japan's Takasaki Radiation Chemistry Establishment. Radiation vulcanized natural rubber latex (RVNRL) has many advantages over the conventional sulfur vulcanized latex, such as absence of nitrosamine and low cytotoxicity. Radiation crosslinking is a room temperature process, itself an important cost advantage, it is easily controlled and desired extend of crosslinking is easily achieved by controlling the dose (irradiation time). Disadvantages of RVNRL to be improved are poor physical properties of film such as low tensile strength and tear strength. The research groups of Japan, Thailand and Indonesia concentrated on the improvement of physical properties of RVNRL using radiation grafted PMMA as additive [2]. F. Sundardi and W. Sofiarti have reported that tensile strength and hardness increased by radiation grafting of styrene onto NR [5]. Ono et al have reported the grafting of MMA onto NR by gamma irradiation at a dose of 5 kGy for producing thermoplastic elastomers [4]. The objective of this project is to report the results of studies of radiation graft-copolymerization of methyl methacrylate (MMA) or styrene (St) onto natural rubber latex in order to improve their physico-mechanical properties and evaluation of grafted material using Small-Angle Neutron Scattering through FNCA Project. The grafting degree of MMA and St onto NR increased with the increase of irradiation dose and monomer concentration. The alteration of grafted products structure was determined by IR method. Tensile strength, Shore A hardness, 100% modulus of grafted products increased with the increase of monomer concentration and irradiation dose while elongation at break decreased. The grafted products were characterized by Transmission Electron

  16. Study of the effect of ionizing radiation on the structure of natural rubber latex by positron annihilation technique

    International Nuclear Information System (INIS)

    Lopez Saldana, I.R.

    1993-01-01

    At the present research, were studied the changes in natural rubber latex structure, due to electron beam by a 3 MeV, 25 m A Dynamitron electron accelerator. The natural rubber latex was irradiated at 30, 40 and 50 kGy/s dose rate, over a total dose range from 150 to 250 kGy, for each dose rate used. From natural rubber latex irradiated films were prepared by casting with 0.7 mm. thickness. In the main part, the study was made by positron annihilation lifetime (PAL), this technique is unique in the determination of free-volume properties due to the fact that positronium atom (Ps) is found to be preferentially localized in the free-volume region of polymeric materials. The positron lifetime measurements were performing using a gamma-gamma coincidence system. These results were analyzed by PATFIT-88 program computer into three components, the long-lived component for orthopositronium (o-Ps) with parameters lifetime (τ 3 ) and formation intensity (I 3 ), were plotted and analyzed for each dose rate and total dose used. Besides with τ 3 were calculated the mean free-volume size based on the spherical model for the free-volume bubble, found that the free-volume decrease slightly with the total dose due to the crosslinking of natural rubber latex. Besides was studied the effect of dose rate on tensile strength, the tensile strength is increased with the total dose although there was not a clear effect due to the dose rate. Also the films were subjected to aging in order to determined the thermal stability of natural rubber latex irradiated, the results show that the films have good stability. Besides was used the infrared spectroscopy to determine the changes due to the crosslinking by variations in the characteristically absorption bands for cis 1,4-polyisoprene. (Author)

  17. Preparation of composites of national rubber latex (NRL) - portland cement mould. Vol. 3

    International Nuclear Information System (INIS)

    Dessouki, A.M.; Taher, N.H.; El-Nahas, H.H.

    1996-01-01

    The aim of this study is to prepare some polymeric mould using national rubber latex (NRL) - portland cement composites based on a delayed- action mechanism. Factors affecting the preparation process such as concentration, mixing percentage, additives and their effect on what is regarded as a delayed action coacervant combination was studied. Composites of national latex (NRL) - portland cement would were prepared as two separate parts. The stabilized natural rubber latex (NRL) 100 parts with hydroxy ethyl cellulose (HEC) 2 parts as stabilizer and a delayed - action coacervant (sodium meta silicate as a delaying agent) 5 parts on one hand and the dry blend of cement 65 parts soluble in 65 parts of water as a paste on the other hand were mixed thoroughly on site. (HEC) was added to the rubber latex to prevent the coagulation of the rubber latex with the electrolyte (sodium meta silicate) present in the rubber mixture. Two kinds of stabilization occurred in the rubber part, namely steric stabilization and the stabilization against electrolyte. The effect of delayed - action coacervant (sodium meta silicate) on the initial setting time of rubber - cement mould showed that the molding process did not occur at sodium meta silicate concentration less than 2.66 parts per 100 parts of rubber latex (phr), and the optimum concentration used was 5% parts of rubber latex. It was observed that addition of a delaying agent (Sodium meta silicate) to the rubber part enhanced the delaying mechanism in the time needed for the molding process, while the addition of the delaying agent to the cement part did not have any effect on retardation of the molding process. Chemical coacervants function mainly by reducing the ζ potential which is associated with the electrical double layer surrounding the latex particle. This reduction may brought about in at least three distinct ways which take place in the system studied. 5 figs., 3 tabs

  18. Preparation of composites of national rubber latex (NRL) - portland cement mould. Vol. 3

    Energy Technology Data Exchange (ETDEWEB)

    Dessouki, A M; Taher, N H; El-Nahas, H H [National Center for Radiation Research and Technology, Atomic Energy Athority, Cairo (Egypt)

    1996-03-01

    The aim of this study is to prepare some polymeric mould using national rubber latex (NRL) - portland cement composites based on a delayed- action mechanism. Factors affecting the preparation process such as concentration, mixing percentage, additives and their effect on what is regarded as a delayed action coacervant combination was studied. Composites of national latex (NRL) - portland cement would were prepared as two separate parts. The stabilized natural rubber latex (NRL) 100 parts with hydroxy ethyl cellulose (HEC) 2 parts as stabilizer and a delayed - action coacervant (sodium meta silicate as a delaying agent) 5 parts on one hand and the dry blend of cement 65 parts soluble in 65 parts of water as a paste on the other hand were mixed thoroughly on site. (HEC) was added to the rubber latex to prevent the coagulation of the rubber latex with the electrolyte (sodium meta silicate) present in the rubber mixture. Two kinds of stabilization occurred in the rubber part, namely steric stabilization and the stabilization against electrolyte. The effect of delayed - action coacervant (sodium meta silicate) on the initial setting time of rubber - cement mould showed that the molding process did not occur at sodium meta silicate concentration less than 2.66 parts per 100 parts of rubber latex (phr), and the optimum concentration used was 5% parts of rubber latex. It was observed that addition of a delaying agent (Sodium meta silicate) to the rubber part enhanced the delaying mechanism in the time needed for the molding process, while the addition of the delaying agent to the cement part did not have any effect on retardation of the molding process. Chemical coacervants function mainly by reducing the {zeta} potential which is associated with the electrical double layer surrounding the latex particle. This reduction may brought about in at least three distinct ways which take place in the system studied. 5 figs., 3 tabs.

  19. Silver nanoparticles delivery system based on natural rubber latex membranes

    International Nuclear Information System (INIS)

    Guidelli, Éder José; Kinoshita, Angela; Ramos, Ana Paula; Baffa, Oswaldo

    2013-01-01

    The search for new materials for biomedical applications is extremely important. Here, we present results on the performance of a silver nanoparticles delivery system using natural rubber latex (NRL) as the polymeric matrix. Our aim was to obtain an optimized wound dressing by combining materials with potential healing action. The synthesis of silver nanoparticles and their characterization by UV–Vis spectroscopy, transmission electron microscopy, zeta potential, dynamic light scattering, and Fourier transform infrared spectroscopy (FTIR) are depicted. The NRL membranes are good matrix for silver nanoparticles and allow for their gradual release. The release of 30 nm silver nanoparticles by the NRL membranes depends on their mass percentage in NRL membranes. The total concentration of AgNP released by the NRL membranes was calculated. The AgNP attached to the cis-isoprene molecules in the NRL matrix remain attached to the membrane (∼0.1 % w/w). So, only the AgNP bound to the non-rubber molecules are released. FTIR spectra suggest that non-rubber molecules, like aminoacids and proteins, associated with the serum fraction of the NRL may be attached to the surfaces of the released nanoparticles, thereby increasing the release of such molecules. The released silver nanoparticles are sterically stabilized, more stable and well dispersed. Because the serum fraction of the NRL is responsible for the angiogenic properties of the matrix, the silver nanoparticles could increment the angiogenic properties of NRL. This biomaterial has desirable properties for the fabrication of a wound dressing with potential healing action, since it combines the angiogenic and antibacterial properties of the silver nanoparticles with the increased angiogenic properties of the NRL.Graphical AbstractThe AgNP attached to the cis-isoprene molecules remain in the NRL matrix and only the AgNP bound to the non-rubber molecules (NRL serum fraction) are released. The released AgNP are sterically

  20. Silver nanoparticles delivery system based on natural rubber latex membranes

    Energy Technology Data Exchange (ETDEWEB)

    Guidelli, Eder Jose, E-mail: ederguidelli@gmail.com [Universidade de Sao Paulo/FFCLRP-DF (Brazil); Kinoshita, Angela [Universidade do Sagrado Coracao (Brazil); Ramos, Ana Paula [Universidade de Sao Paulo/FFCLRP-DQ (Brazil); Baffa, Oswaldo [Universidade de Sao Paulo/FFCLRP-DF (Brazil)

    2013-04-15

    The search for new materials for biomedical applications is extremely important. Here, we present results on the performance of a silver nanoparticles delivery system using natural rubber latex (NRL) as the polymeric matrix. Our aim was to obtain an optimized wound dressing by combining materials with potential healing action. The synthesis of silver nanoparticles and their characterization by UV-Vis spectroscopy, transmission electron microscopy, zeta potential, dynamic light scattering, and Fourier transform infrared spectroscopy (FTIR) are depicted. The NRL membranes are good matrix for silver nanoparticles and allow for their gradual release. The release of 30 nm silver nanoparticles by the NRL membranes depends on their mass percentage in NRL membranes. The total concentration of AgNP released by the NRL membranes was calculated. The AgNP attached to the cis-isoprene molecules in the NRL matrix remain attached to the membrane ({approx}0.1 % w/w). So, only the AgNP bound to the non-rubber molecules are released. FTIR spectra suggest that non-rubber molecules, like aminoacids and proteins, associated with the serum fraction of the NRL may be attached to the surfaces of the released nanoparticles, thereby increasing the release of such molecules. The released silver nanoparticles are sterically stabilized, more stable and well dispersed. Because the serum fraction of the NRL is responsible for the angiogenic properties of the matrix, the silver nanoparticles could increment the angiogenic properties of NRL. This biomaterial has desirable properties for the fabrication of a wound dressing with potential healing action, since it combines the angiogenic and antibacterial properties of the silver nanoparticles with the increased angiogenic properties of the NRL.Graphical AbstractThe AgNP attached to the cis-isoprene molecules remain in the NRL matrix and only the AgNP bound to the non-rubber molecules (NRL serum fraction) are released. The released AgNP are

  1. The influence of temperature and reaction time in the degradation of natural rubber latex

    International Nuclear Information System (INIS)

    Siti Zaleha Isa; Rosiyah Yahya; Aziz Hassan; Mohd Tahir

    2007-01-01

    Liquid natural rubber (LNR /LENR) should be considered as a new material instead of a new type of rubber though they have the same configuration as the rubber used. In this work, thermal degradation of natural rubber latex was carried out to obtain LNR/LENR by varying the reaction time at different temperatures. The degraded polymers were characterized structurally using FTIR and NMR spectroscopies and the average molecular weights were determined by membrane-osmometry and viscometry. (author)

  2. Antioxidant and sensitizer effect on the stability of natural rubber latex vulcanized by gamma rays

    International Nuclear Information System (INIS)

    Canavel, V.

    1993-01-01

    The natural rubber latex was vulcanized by gamma rays and electrons beam, in the presence and absence of sensitizer at room temperature. The sensitizers were the following; n-butyl acrylate (n-BA) / t-butyl hydroperoxide (t-B H) / KOH, C Cl 4 / potassium laurate and n-BA / KOH. The studied antioxidants, Irganox 1520, Vulcanox SP and Vulcanox BKF, were added to the latex after irradiation. Among the studied antioxidants in function of tensile strength (TS) after the aging of rubber plates, the Irganox was the best efficient on the gamma vulcanization in the presence of n-BA/t-B H/KOH, because only 0,20 p hr is enough to obtain the greatest increase of TS, that was 34%, 12 MPa to 16 MPa. The formulating method of latex with the sensitizer constituted the 3,0 p hr of n-BA/ 0,1 p hr of t-B H and 0,2 p hr of KOH, was evaluated respecting the TS of rubber plates. The electrons beam vulcanization produces the greatest reversible perturbance in the colloidal stability of latex after irradiation caused by radiolytic species absorption that promotes the increase of particle size. The antioxidant also contributes to reversible destabilization of gamma irradiated latex, because it is also adsorbed by particles surface. The relation between the latex viscosity and the TS of respective rubber plates is reverse, showing the latex stability affects the quality of rubber goods. (author)

  3. Trial production of low protein irradiated natural rubber latex by low energy electron beam in pilot scale

    International Nuclear Information System (INIS)

    Utama, Marga; Yoshii, F.; Kume, T.

    2006-01-01

    Three importance factors for producing low protein by low energy electron beam (250 keV/10 mA) irradiation in pilot scale (20 liters per bath) with 1,9-nonediol diacrylate (NDA) namely: maturation time of natural rubber latex before irradiation, treatment of irradiated natural rubber latex (INRL) before and after centrifugation, and standard irradiation method has been carried out. The results showed that the optimum irradiation time for producing INRL with 5 phr (part hundred ratio of rubber) of NDA as sensitize agent, and with the rotation speed of agitation 210 rpm (rotation per minutes) was between 20-30 minutes. By using this condition tensile strength of the INRL film was 26 MPa. The maturation of natural rubber latex before irradiation is the key for driving the quality of INRL. Water extractable protein content of INRL after leaching in 1% ammonia solution for 30 minutes at room temperature was around 47 μ/g, and after adding with 1 phr of PVA (poly vinyl alcohol) or 0.1 phr CMC (carboxy methyl cellulose) the water extractable protein content decrease less than 6 μ/g. (author)

  4. Graft Copolymerization of Methyl Methacrylate Monomer onto Starch and Natural Rubber Latex Initiated by Gamma Irradiation

    Directory of Open Access Journals (Sweden)

    S. Iskandar

    2011-04-01

    Full Text Available To obtain the degradable plastic, the graft copolymerization of methyl methacrylate onto starch and natural rubber latex was conducted by a simultaneous irradiation technique. Gamma-ray from cobalt-60 source was used as the initiator. The grafted copolymer of starch-polymethyl methacrylate and the grafted copolymer of natural rubber-polymethyl methacrylate were mixed in the blender, and dried it in the oven. The dried grafted copolymer mixture was then molded using hydraulic press machine. The effect of irradiation dose, composition of the grafted copolymer mixture, film forming condition and recycle effect was evaluated. The parameters observed were tensile strength, gel fraction and soil burial degradability of grafted copolymer mixture. It was found that the tensile strength of grafted copolymer mixture increased by -ray irradiation. Increasing of the grafted copolymer of natural rubber-polymethyl methacrylate content, the gel fraction and tensile strength of the grafted copolymer mixture increased. The tensile strength of the grafted copolymer mixture was increased from 18 MPa to 23 MPa after recycled (film forming reprocessed 3 times. The grafted copolymer mixture was degraded completely after soil buried for 6 months

  5. Prevalence of Allergy to Natural Rubber Latex and Potential Cross Reacting Food in Operation Room Staff in Shiraz Hospitals -2006

    OpenAIRE

    H Nabavizade; R Amin

    2007-01-01

    Introduction & Objective: Allergic reactions to natural rubber latex have increased during past 10 years especially among health care workers and patients with high exposure to latex allergens. Allergic reaction to latex is related to many diseases like occupational asthma. This study was performed to determine the prevalence of allergy to natural rubber latex and potential cross reacting food in operation room staff in Shiraz hospitals. Materials & Methods: In this cross-sectional descr...

  6. Costs and return analysis in rubber latex production in Edo State ...

    African Journals Online (AJOL)

    The study examined the costs and return analysis in rubber latex production in Edo Sate, Nigeria. Multi-stage sampling method was adopted to select 96 smallholder rubber framers for the study. The first stage was a purposive sampling of two LGAs and then simple random sampling of 6 villages each from the two LGA.

  7. Latex Rubber Gloves as a Sampling Dosimeter Using a Novel Surrogate Sampling Device.

    Science.gov (United States)

    Sankaran, Gayatri; Lopez, Terry; Ries, Steve; Ross, John; Vega, Helen; Eastmond, David A; Krieger, Robert I

    2015-01-01

    Pesticide exposure during harvesting of crops occurs primarily to the workers' hands. When harvesters wear latex rubber gloves for personal safety and hygiene harvesting reasons, gloves accumulate pesticide residues. Hence, characterization of the gloves' properties may be useful for pesticide exposure assessments. Controlled field studies were conducted using latex rubber gloves to define the factors that influence the transfer of pesticides to the glove and that would affect their use as a residue monitoring device. A novel sampling device called the Brinkman Contact Transfer Unit (BCTU) was constructed to study the glove characteristics and residue transfer and accumulation under controlled conditions on turf. The effectiveness of latex rubber gloves as sampling dosimeters was evaluated by measuring the transferable pesticide residues as a function of time. The validation of latex rubber gloves as a residue sampling dosimeter was performed by comparing pesticide transfer and dissipation from the gloves, with the turf transferable residues sampled using the validated California (CA) Roller, a standard measure of residue transfer. The observed correlation (Pearson's correlation coefficient R(2)) between the two methods was .84 for malathion and .96 for fenpropathrin, indicating that the BCTU is a useful, reliable surrogate tool for studying available residue transfer to latex rubber gloves under experimental conditions. Perhaps more importantly, these data demonstrate that latex gloves worn by workers may be useful quantifiable matrices for measuring pesticide exposure.

  8. Proceedings of the international symposium on radiation vulcanization of natural rubber latex

    International Nuclear Information System (INIS)

    Machi, Sueo

    1990-01-01

    The First International Symposium on Radiation Vulcanization of Natural Rubber Latex (RVNRL) was held from 26 to 28 July 1989 at Tokyo and Takasaki. In these proceedings, thirty six papers presented at the Symposium are compiled. Main topics are commercial application of RVNRL, characterization of NR latex and vulcanization, properties of radiation vulcanized NR latex, development of sensitizers, mechanism of RVNRL, RVNRL with electron beams, and new Co-60 irradiator for RVNRL. Absence of nitrosamines and low cytotoxicity of radiation vulcanized NR latex are recognized as the remarkable advantages of RVNRL. The radiation vulcanization process for the production of protective rubber gloves for radioactive contamination was presented as the first commercial success in RVNRL. It was reported that various kinds of rubber articles for medical uses have being developed in West Germany. A sensitizer system consisting of n-butyl acrylate and t-butyl hydroperoxide was found to reduce the vulcanization dose to 8 kGy. (author)

  9. Rubber/clay nanocomposites by combined latex compounding and melt mixing: A masterbatch process

    International Nuclear Information System (INIS)

    Tan, Jinghua; Wang, Xiaoping; Luo, Yuanfang; Jia, Demin

    2012-01-01

    Highlights: → Rubber/Ca-montmorillonite nanocomposites were prepared by the masterbatch process. → Latex compounding method is efficient to improve the Ca-montmorillonite dispersion. → Exfoliated structure was obtained in the masterbatch by latex compounding method. → Intercalated and exfoliated structures were achieved in the vulcanizate. → The properties of vulcanizate are improved by the addition of Ca-montmorillonite. -- Abstract: Rubber/Ca-montmorillonite (Ca-MMT) nanocomposites with well exfoliated Ca-MMT layers were prepared by combination of latex compounding and melt mixing. Firstly, a high Ca-MMT content masterbatch was co-coagulated by natural rubber (NR) latex and modified Ca-MMT aqueous suspension through latex compounding. The masterbatch was added in the system of styrene butadiene rubber (SBR) and epoxidized natural rubber (ENR) by melt mixing subsequently. The X-ray diffraction (XRD) and transmission electronic microscopy (TEM) results showed that intercalated and exfoliated nanocomposites were obtained by the masterbatch technique. The effects of modified Ca-MMT introduction into the rubber matrix, via the masterbatch technique, on the properties of the resulting composites were studied. It was found that the vulcanization was hindered by the incorporation of modified Ca-MMT, while mechanical performances, thermal stability and aging resistance were improved. The increasingly glass transition temperature and the storage modulus with the loading of modified Ca-MMT were measured by dynamic mechanical analysis (DMA).

  10. Ciprofloxacin release using natural rubber latex membranes as carrier.

    Science.gov (United States)

    Dias Murbach, Heitor; Jaques Ogawa, Guilherme; Azevedo Borges, Felipe; Romeiro Miranda, Matheus Carlos; Lopes, Rute; Roberto de Barros, Natan; Guedes Mazalli, Alexandre Vinicius; Gonçalves da Silva, Rosângela; Ferreira Cinman, José Luiz; de Camargo Drago, Bruno; Donizetti Herculano, Rondinelli

    2014-01-01

    Natural rubber latex (NRL) from Hevea brasiliensis is easily manipulated, low cost, is of can stimulate natural angiogenesis and cellular adhesion, is a biocompatible, material and presents high mechanical resistance. Ciprofloxacin (CIP) is a synthetic antibiotic (fluoroquinolone) used in the treatment of infection at external fixation screws sites and remote infections, and this use is increasingly frequent in medical practice. The aim of this study was to develop a novel sustained delivery system for CIP based on NRL membranes and to study its delivery system behavior. CIP was found to be adsorbed on the NRL membrane, according to results of energy dispersive X-ray spectroscopy. Results show that the membrane can release CIP for up to 59.08% in 312 hours and the mechanism is due to super case II (non-Fickian). The kinetics of the drug release could be fitted with double exponential function X-ray diffraction and Fourier transform infrared (FTIR) spectroscopy shows some interaction by hydrogen bound, which influences its mechanical behavior.

  11. Effect of filler loading of characteristic natural rubber latex (NRL) film filled with nanocrystal cellulose (NCC) and dipersion agent polyvinylpyrrolidone (PVP)

    Science.gov (United States)

    Harahap, Hamidah; Lubis, Yuni Aldriani; Taslim, Iriany, Nasution, Halimatuddahliana; Agustini, Hamda Eka

    2018-04-01

    A study has been conducted on the effect of filler loading on NRL films filled with NCC from corn cob waste. This study reviews on the filler loading of NRL film characteristics. The process begins with the production of NCC filler and then proceed with the production NRL film which is processed by coagulant dipping method. NRL is filled with NCC and PVP as dispersion agent of 2, 4, 3, 8 grams (filler loading) and 1% PVP by weight. The production of NRL film started with pre-vulcanization process at 70 °C and followed by vulcanization process at 110 °C for 20 minutes. The results showed that higher filler loading improved the higher crosslink density and mechanical properties of NRL film.

  12. Isolation rubber latex binary composites consisting of cotton and poly-N, N-dimethyl-N, N-diallilammony chloride

    Directory of Open Access Journals (Sweden)

    J. Cornejo Tueros

    2012-01-01

    Full Text Available The paper discusses the application of rubber from latex binary coagulating agent consisting of cotton - textile waste and polymeric quaternary ammonium salts. The influence on the process of extracting rubber from latex flow coagulating agent temsperatury and concentration of the dispersed phase.

  13. Mechanism of n-butyl acrylate sensitization action in radiation vulcanization of natural rubber latex

    International Nuclear Information System (INIS)

    Sabharwal, S.; Chaudhari, C.V.; Bhardwaj, Y.K.; Majali, A.B.; Das, T.N.

    1996-01-01

    In order to understand the role of n-butyl acrylate (nBA) in radiation vulcanization of natural rubber latex, pulse radiolysis technique has been utilized to study the reactions of the transient species produced by reaction of OH . , e- aq and H . atoms with nBA in aqueous solutions. The results show that transients produced by reaction of e- aq with nBA alone are capable of propagating the polymerization reaction and enhance the vulcanization process. These results have been further confirmed by studying the effect of electron scavengers on the vulcanization behaviour of natural rubber latex in presence of nBA. (author). 3 refs., 3 figs

  14. Gamma irradiator design concepts for radiation vulcanisation of natural rubber latex

    International Nuclear Information System (INIS)

    Aggarwal, K.S.; Muralidharan, P.; Apte, M.G.; Kalurkar, A.R.; Shah, B.M.

    1990-01-01

    Radiation vulcanisation of natural rubber latex (NRL) is a new and yet unproven technology and one which involves undefined problems of consumer acceptance and high degree of radiation risk. Therefore, the designer should take care that the initial capital cost of the plant is as low as possible to keep the unit processing cost low during the initial lean period of the product requirement by the market. Three irradiators to process natural rubber latex have been designed as per capacity requirement of the user. Their salient features are described. (author). 2 tabs., 24 figs

  15. Mechanical and morphological properties of kenaf powder filled natural rubber latex foam

    Energy Technology Data Exchange (ETDEWEB)

    Karim, Ahmad Fikri Abdul, E-mail: a.fikri-89@yahoo.com; Ariff, Zulkifli Mohamad [School of Materials and Mineral Resources Engineering, Engineering Campus, Universiti Sains Malaysia, 14300 Nibong Tebal, Pulau Pinang (Malaysia); Ismail, Hanafi [Cluster for Polymer Composites (CPC), Science and Engineering Research Centre, Engineering Campus, Universiti Sains Malaysia,14300 Nibong Tebal, Pulau Pinang (Malaysia)

    2015-07-22

    This research is carried out by incorporate kenaf powder with natural rubber latex (NRL) compound and is foamed to make natural rubber latex foam (NRLF) by using a well known technique called Dunlop method. Different loading of kenaf powder was added to NRL compound and was foamed to make NRLF. The tensile properties, and morphology of kenaf filled NRLF was studied. Increase in kenaf loading reduced the tensile strength and elongation at break and of a compound. Modulus at 100% elongation of the compound increased with increased in filler loading. The morphological and micro structural characterization has been performed by using scanning electron microscopy (SEM)

  16. Mechanical and morphological properties of kenaf powder filled natural rubber latex foam

    International Nuclear Information System (INIS)

    Karim, Ahmad Fikri Abdul; Ariff, Zulkifli Mohamad; Ismail, Hanafi

    2015-01-01

    This research is carried out by incorporate kenaf powder with natural rubber latex (NRL) compound and is foamed to make natural rubber latex foam (NRLF) by using a well known technique called Dunlop method. Different loading of kenaf powder was added to NRL compound and was foamed to make NRLF. The tensile properties, and morphology of kenaf filled NRLF was studied. Increase in kenaf loading reduced the tensile strength and elongation at break and of a compound. Modulus at 100% elongation of the compound increased with increased in filler loading. The morphological and micro structural characterization has been performed by using scanning electron microscopy (SEM)

  17. Pilot Scale Production of Irradiated Natural Rubber Latex and its Dipping Products

    Directory of Open Access Journals (Sweden)

    M. Utama

    2005-07-01

    Full Text Available One hundred and fifty kg natural rubber latex (NRL before and after concentration were added with 3 phr (part hundred ratio of rubber normal butyl acrylate, then the mixture were irradiated at 25 kGy by gamma rays of 60Co in pilot scale. The irradiated natural rubber latex (INRL were then being to use for producing rubber products such as condom, surgical gloves, and spygmomanometer in factory scale. The quality of INRL and rubber products such as : total solid content (TSC, dry rubber content (DRC, KOH, VFA and MST number, tensile strength, modulus, elongation at break, extractable protein content, and response against Type I allergy etc. were evaluated. The economic aspect for producing INRL by means of Gamma Irradiator (GI and Electron Beam Machine (EBM such as payback period (PP, net present value (NPV and internal rate return (IRR were calculated. The results showed that the latex properties of INRL such as DRC, TSC, KOH, VFA, and MST number are not only found to the requirement of the ISO 2004 standard but also the latex has low protein, lipid, and carbohydrate content. The physical and mechanical properties (tensile strength, modulus, and elongation at break of rubber dipping products such as condom, gloves, and sphygmomanometer are not only found to the requirement of ISO 4074, ISO 10282, and ANSI/AAMI SP-1994 standards, but also the allergic response tested clinical latex-sensitive protein allergen by ELISA test on gloves, and by SPT test on condom are found to be negative. It indicates that production of INRL or PVNRL or RVNRL by EBM 250 keV/10 mA, was more cheap than by using gamma γ irradiator 200 kCi, or sulfur vulcanization. The value of PBP (payback period was 2,1 years, NPV (net present value was 4,250 US $, PI (profitability index 1,06 and IRR (internal rate of returns was 25,0%.

  18. Analysis of Aqueous Extractable Protein in Radiation Pre vulcanized Natural Rubber Latex (RVNRL) And Sulphur Pre vulcanized Natural Rubber Latex (SVNRL)

    International Nuclear Information System (INIS)

    Sofian Ibrahim; Mohd Noor Wadi Mat Lazim; Syuhada Ramli; Keong, C.C.; Khairul Hisyam Mohd Yusof; Muhammad Saiful Omar; Najib Mohd Zakey; Hafizuddin Maseri; Noor Hasni Mohd Ali

    2015-01-01

    The use of radiation do not only produces Radiation Pre vulcanized Natural Rubber Latex (RVNRL) that can be used for the production of nitrosamines free products, moreover, RVNRL also able to exclude type IV allergy that caused by high protein content in the products. Leaching water from production of finger coat from RVNRL and Sulphur Pre vulcanized Natural rubber Latex (SVNRL) has been collected. Extractable protein content from water samples measured according to the test protocol ASTM D5712-2010. Water from leaching process of finger coat made from RVNRL showed a higher protein content than SVNRL. This explains why RVNRL based products contain very low protein content and thus reduce the risk of Type IV allergy. (author)

  19. Study on preparation of new antioxidants for radiation vulcanized natural rubber latex product. Antioxidant from keratin

    International Nuclear Information System (INIS)

    Nguyen Quoc Hien; Nguyen Van Toan; Vo Tan Thien; Le Hai

    2000-01-01

    The thermo-oxidative aging resistance of radiation vulcanization of natural rubber latex (RVNRL) products should be adequately by using suitable antioxidants or new kind of effective antioxidant. This work presents the results of preparation of natural antioxidant from hair keratin. Characteristics and effectiveness of resultant antioxidant are also presented. The results obtained indicates that antioxidant made from hair keratin is safe and effective for rubber products from RVNRL. (author)

  20. Comparative Transcriptome Analysis of Latex Reveals Molecular Mechanisms Underlying Increased Rubber Yield in Hevea brasiliensis Self-Rooting Juvenile Clones

    OpenAIRE

    Li, Hui-Liang; Guo, Dong; Zhu, Jia-Hong; Wang, Ying; Chen, Xiong-Ting; Peng, Shi-Qing

    2016-01-01

    Rubber tree (Hevea brasiliensis) self-rooting juvenile clones (JCs) are promising planting materials for rubber production. In a comparative trial between self-rooting JCs and donor clones (DCs), self-rooting JCs exhibited better performance in rubber yield. To study the molecular mechanism associated with higher rubber yield in self-rooting JCs, we sequenced and comparatively analyzed the latex of rubber tree self-rooting JCs and DCs at the transcriptome level. Total raw reads of 34,632,012 ...

  1. Color Spectrum Properties of Pure and Non-Pure LATEX in Discriminating Rubber Clone Series

    International Nuclear Information System (INIS)

    Noor Aishah Khairuzzaman; Hadzli Hashim; Nina Korlina Madzhi; Noor Ezan Abdullah; Faridatul Aima Ismail; Ahmad Faiz Sampian; Azhana Fatnin Che Will

    2015-01-01

    A study of color spectrum properties for pure and non-pure latex in discriminating rubber clone series has been presented in this paper. There were five types of clones from the same series being used as samples in this study named RRIM2002, RRIM2007, RRIM2008, RRIM2014, and RRIM3001. The main objective is to identify the significant color spectrum (RGB) from pure and non-pure latex that can discriminate rubber clone series. The significant information of color spectrum properties for pure and non-pure latex is determined by using spectrometer and Statistical Package for the Social Science (SPSS). Visible light spectrum (VIS) is used as a radiation light of the spectrometer to emit light to the surface of the latex sample. By using SPSS software, the further numerical analysis of color spectrum properties is being conducted. As the conclusion, blue color spectrum for non-pure is able to discriminate for all rubber clone series whereas only certain color spectrum can differentiate several clone series for pure latex. (author)

  2. Capacitance Regression Modelling Analysis on Latex from Selected Rubber Tree Clones

    International Nuclear Information System (INIS)

    Rosli, A D; Baharudin, R; Hashim, H; Khairuzzaman, N A; Mohd Sampian, A F; Abdullah, N E; Kamaru'zzaman, M; Sulaiman, M S

    2015-01-01

    This paper investigates the capacitance regression modelling performance of latex for various rubber tree clones, namely clone 2002, 2008, 2014 and 3001. Conventionally, the rubber tree clones identification are based on observation towards tree features such as shape of leaf, trunk, branching habit and pattern of seeds texture. The former method requires expert persons and very time-consuming. Currently, there is no sensing device based on electrical properties that can be employed to measure different clones from latex samples. Hence, with a hypothesis that the dielectric constant of each clone varies, this paper discusses the development of a capacitance sensor via Capacitance Comparison Bridge (known as capacitance sensor) to measure an output voltage of different latex samples. The proposed sensor is initially tested with 30ml of latex sample prior to gradually addition of dilution water. The output voltage and capacitance obtained from the test are recorded and analyzed using Simple Linear Regression (SLR) model. This work outcome infers that latex clone of 2002 has produced the highest and reliable linear regression line with determination coefficient of 91.24%. In addition, the study also found that the capacitive elements in latex samples deteriorate if it is diluted with higher volume of water. (paper)

  3. Effects of radio sensitizers in the vulcanization of natural rubber latex induced by gamma radiation

    International Nuclear Information System (INIS)

    Souza, A. de; Canavel, V.; Araujo, S.C. de; Guedes, S.M.L.

    1992-01-01

    The effect of C Cl 4 and n-butyl acrylate as a sensitizer for radiation vulcanization of 60% DRC natural rubber latex with gamma rays, was studied relating tensile strength of vulcanized latex. The vulcanization dose is 200 kGy for natural rubber latex and it decreases to 40 kGy and to 9 kGy in the presence of C Cl 4 / potassium laureate and n-butyl acrylate / t-butyl hydroperoxide, respectively. The H 2 O 2 as a co-sensitizer does not change the efficiency of the combination of these sensitizers. The IV spectra show the formation of C=O after the irradiation as consequence of oxidation reactions. (author)

  4. Analysis of sulfidic linkages formed in natural rubber latex medical gloves by using X-ray absorption near edge structure

    Science.gov (United States)

    Chankrachang, M.; Limphirat, W.; Yongyingsakthavorn, P.; Nontakaew, U.; Tohsan, A.

    2017-09-01

    A study of sulfidic linkages formed in natural rubber (NR) latex medical gloves by using X-ray Absorption Near Edge Structure (XANES) is presented in this paper. The NR latex compound was prepared by using prevulcanization method, that is, it was prevulcanized at room temperature for 24 hrs before utilization. After the 24 hrs of prevulcanization, the latex film samples were obtained by dipping process. The dipped films were subjected to vulcanize at 110°C for 5 to 25 min. It was observed that after the compound was prevulcanized for 24 hrs, polysulfidic linkages were mainly formed in the sample. It was however found that after curing at 110°C for 5-25 min, the polysulfidic linkages are tended to change into disulfide linkages. Especially, in the case of 25 minutes cured sample, disulfide linkages are found to be the main linkages. In term of tensile strength, it was observed that when cure time increased from 5 - 10 min, tensile strengths were also increased. But when the cure time of the film is 25 minutes, tensile strength was slightly dropped. The dropped of tensile strength when cure time is longer than 10 minutes can be ascribed to a degradation of polysulfidic and disulfidic linkages during curing. Therefore, by using XANES analysis, it was found to be very useful to understand the cure characteristic, thus it can be very helpful to optimize cure time and tensile properties of the product.

  5. ENHANCEMENT OF RESISTANCE TO OXIDATIVE DEGRADATION OF NATURAL RUBBER THROUGH LATEX DEGRADATION

    Institute of Scientific and Technical Information of China (English)

    1998-01-01

    A fully characterised natural rubber latex was subjected to mechanical degradation by stirring at intervals. The resistance to oxidative degradation of the different samples were studied by measuring the Plasticity retention indices (PRI).The results show that there is an enhancement of the PRI from 57% for the undegraded rubber to 79% for the one-hour degraded sample. Further degradation resulted in decrease of PRI as time of degradation increased. Therefore, the one-hour degraded sample is a special rubber with high oxidation resistance which is of great importance in engineering.

  6. Evaluation of apparent viscosity of Para rubber latex by diffuse reflection near-infrared spectroscopy.

    Science.gov (United States)

    Sirisomboon, Panmanas; Chowbankrang, Rawiphan; Williams, Phil

    2012-05-01

    Near-infrared spectroscopy in diffuse reflection mode was used to evaluate the apparent viscosity of Para rubber field latex and concentrated latex over the wavelength range of 1100 to 2500 nm, using partial least square regression (PLSR). The model with ten principal components (PCs) developed using the raw spectra accurately predicted the apparent viscosity with correlation coefficient (r), standard error of prediction (SEP), and bias of 0.974, 8.6 cP, and -0.4 cP, respectively. The ratio of the SEP to the standard deviation (RPD) and the ratio of the SEP to the range (RER) for the prediction were 4.4 and 16.7, respectively. Therefore, the model can be used for measurement of the apparent viscosity of field latex and concentrated latex in quality assurance and process control in the factory.

  7. Radiation vulcanization of natural rubber latex (NRL) using low energy electron beam accelerator

    International Nuclear Information System (INIS)

    Feroza Akhtar; Keizo Makuuchi; Fumio Yoshii

    1996-01-01

    The electron beam induced vulcanization of natural rubber latex has been studied using low energy Electron Beam (EB) accelerators of 300, 250 and 175 keV ne latex was irradiated in a special type stainless steel reaction reactor with a stirrer at the bottom of the reactor. From the results it was found that 300 and 250 keV accelerators could effectively vulcanize NRL. But accelerator of 175 keV is too low energy to vulcanize the latex. At the same time a drum type irradiator where thin layer of NRL was irradiated by accelerator, was used for vulcanization of NRL. This type of irradiator also showed good physical properties of vulcanized latex. The effects of beam current and stirrer speed on vulcanization were studied

  8. Study on irradiation condition in radiation vulcanization of natural rubber latex

    International Nuclear Information System (INIS)

    Zhu Nankang; Wang Chunlei; Makuuchi, K.; Yoshii, F.

    1996-01-01

    The effect of gamma rays irradiation dose rates on RVNRL preparation was studied using Malaysian latex added with O.2 phr of KOH and 5 phr n-BA. The results showed, to ensure the tensile strength of the latex film meet the requirement, when applying vulcanisation doses, Dv of 20 kGy 20 and 15 kGy, irradiation dose rates should not be greater than 0. 49 kGy/hr and 1. 6 kGy/hr respectively. Its was found that within the storage time of 20 days there was no change in the physical properties of the latex films

  9. Cytotoxicity Comparison of the Nanoparticles Deposited on Latex Rubber Bands between the Original and Stretched State

    Directory of Open Access Journals (Sweden)

    Jung-Hwan Lee

    2014-01-01

    Full Text Available Understanding the biocompatibility of nanoparticles in dental materials is essential for their safe usage in the oral cavity. In this study, we investigated whether nanoparticles deposited on orthodontic latex rubber bands are involved in the induction of cytotoxicity. A method of stretching to three times (“3L” the length of the latex rubber bands was employed to detach the particles using the original length (“L” for comparison. The cytotoxicity tests were performed on extracts with mouse fibroblasts (L929 and human gingival fibroblasts (HGFs. Fourier transform infrared spectroscopy, ion chromatography, elemental analysis, and inductively coupled plasma mass spectrometry (ICP-MS were performed to detect the harmful components in the extracts from rubber bands. There was a significant decrease in the cell viability in the “L” samples compared with the “3L” samples (P<0.05 in the L929 and HGF cells. This was due to the Ni single crystal nanoparticles (~50nm from the inner surface of “L” samples that were detached in the “3L” samples as well as the Zn ion (~9 ppm detected in the extract. This study revealed that the Ni nanoparticles, as well as Zn ions, were involved in the induction of cytotoxicity from the latex rubber bands.

  10. Radiation vulcanization of natural rubber latex using 250 keV electron beam machine

    Energy Technology Data Exchange (ETDEWEB)

    Chirinos, H.; Yoshii, F.; Makuuchi, K.; Lugao, A. E-mail: ablugao@net.ipen.br

    2003-08-01

    The sensitized radiation vulcanization of natural rubber latex has been carried out with 250 keV electrons. Latex was irradiated over a range of the beam current from 5 to 20 mA in the presence of sensitizers like the n-butyl acrylate (n-BA). The vulcanization dose decreases with increasing beam current condition. The rate of vulcanization (R{sub vul}) depends on the beam current (I) as given by the equation R{sub vul}=kI{sup 0.6}.

  11. Trial Production of Surgical Gloves from Irradiated Natural Rubber Latex on Factory Scale

    Directory of Open Access Journals (Sweden)

    M. Utama

    2005-07-01

    Full Text Available Trial production of surgical gloves from irradiated natural rubber latex at the PT. Laxindo Utama Serang Banten glove factory has been carried out. The variation of heating temperature and leaching time during processing were evaluated. The physical and mechanical properties and the protein allergen respond of surgical gloves using ELISA method were measured. The results showed that the physical and mechanical of surgical gloves such as tensile strength, modulus, and elongation at break arefound to meet the requirements of the ISO or SNI standard for surgical gloves. While the allergic response through clinical tested latex-sensitive protein allergen known as ELISA test is found to be negative.

  12. Drying of latex films and coatings: Reconsidering the fundamental mechanisms

    DEFF Research Database (Denmark)

    Kiil, Søren

    2006-01-01

    The two existing theories describing drying of latex films or coatings are reconsidered. Subsequently, a novel mathematical drying model is presented, the simulations of which can match and explain experimental drying rate data of two previous investigations with latex films. In contrast to previ......The two existing theories describing drying of latex films or coatings are reconsidered. Subsequently, a novel mathematical drying model is presented, the simulations of which can match and explain experimental drying rate data of two previous investigations with latex films. In contrast...... to previous model studies, but in agreement with observations, simulations suggest that during the falling rate period of the drying process of a latex film, a porous skin of partly coalesced latex particles is indeed formed, which limits transport of water vapour from the receding air-liquid interphase...... to the surface of the film. The value of the effective diffusion coefficient of water vapour in the dry and partly coalesced layer (7 x 10(-7) m(2)/s at 19-24 degrees C), the adjustable parameter of the model for the falling rate period, was found to be independent of initial wet film thickness (89-1322 mu m...

  13. Prevalence of Allergy to Natural Rubber Latex and Potential Cross Reacting Food in Operation Room Staff in Shiraz Hospitals -2006

    Directory of Open Access Journals (Sweden)

    H Nabavizade

    2007-07-01

    Full Text Available Introduction & Objective: Allergic reactions to natural rubber latex have increased during past 10 years especially among health care workers and patients with high exposure to latex allergens. Allergic reaction to latex is related to many diseases like occupational asthma. This study was performed to determine the prevalence of allergy to natural rubber latex and potential cross reacting food in operation room staff in Shiraz hospitals. Materials & Methods: In this cross-sectional descriptive study five hundred eighty operation room staff of ten private and state hospitals in Shiraz completed latex allergy questionnaire. They were questioned about personal history and previous history of latex sensitivity, symptoms of latex reactivity and about other allergies particularly to foods that may cross react with latex. Informed consent was obtained and skin prick testing was performed with natural rubber latex. Skin prick tests were done with three potentially cross reacting food (banana, Kiwi, and potato. The obtained data were analyzed with SPSS software and Chi-square test. Results: Among the 580 operation room workers 104 (17.9 % of participants were positive to latex skin test. We found a significant association between positive skin test to latex in operation room staff and atopy, urticaria and food allergy. Positive skin test to latex related to positive kiwi skin test (p<0.05. The prevalence did not vary by sex, age, education, surgical and non surgical glove users, history of contact dermatitis or smoking status. Conclusion: Latex allergy has a high prevalence in personnel of operation room. Evaluation of present symptom and prediction of future disease necessitate screening test in individuals at risk.

  14. Radiation-induced grafting polymerization of MMA onto polybutadiene rubber latex

    International Nuclear Information System (INIS)

    Peng Jing; Wang Maolin; Qiao Jinliang; Wei Genshuan

    2005-01-01

    The grafting of methyl methacrylate (MMA) onto polybutadiene rubber latex by the direct radiation method was carried out. The effects of monomer concentration, absorbed dose and dose rate of gamma rays on the grafting yield were investigated. The graft copolymers were characterized by transmission electron microscopy (TEM), FTIR spectroscopy, and differential scanning calorimetry. TEM photographs revealed that the core-shell structures of latex particles are formed at low MMA content, and with the increasing of MMA content, the semi-IPN-like structure with core-shell could be developed due to the high gel fraction of polybutadiene (PBD) seed particles. In addition, infrared analysis confirmed that MMA could be grafted onto PBD molecular chains effectively under appropriate irradiation conditions. The interfacial adhesion between PBD rubber (core) and PMMA (shell) phases could be enhanced with the increase of MMA concentration

  15. Radiation graft copolymerization of n-butyl acrylate on natural rubber latex

    International Nuclear Information System (INIS)

    Sundardi, F.; Kadariah, S.

    1986-01-01

    A method of radiation graft copolymerization of n-butyl acrylate (NBA) on natural rubber (NR) latex has been studied. The rate of conversion increases with the increase of NBA in latex. An irradiation dose of about 12 kGy is needed to obtain 90% conversion with 40 phr of NBA in latex. Tensile strength, tear strength, and elongation at break of grafted NR are found to decrease with increasing degree of grafting. The physical strength of a vulcanizate prepared from a mixture of NR and ply-NBA was found to be better than that of NBA-NR graft copolymer vulcanizate. The graft copolymerization reaction takes place in the outer layer of NR particles, and because the secondary bonds between poly-NBA molecules may be weaker than those between NR molecules, the existence of a poly-NBA layer in NR particles will decrease its physical strength

  16. Evaluation of peptides release using a natural rubber latex biomembrane as a carrier.

    Science.gov (United States)

    Miranda, M C R; Borges, F A; Barros, N R; Santos Filho, N A; Mendonça, R J; Herculano, R D; Cilli, E M

    2018-05-01

    The biomembrane natural (NRL-Natural Rubber Latex), manipulated from the latex obtained from the rubber tree Hevea brasiliensis, has shown great potential for application in biomedicine and biomaterials. Reflecting the biocompatibility and low bounce rate of this material, NRL has been used as a physical barrier to infectious agents and for the controlled release of drugs and extracts. The aim of the present study was to evaluate the incorporation and release of peptides using a latex biomembrane carrier. After incorporation, the release of material from the membrane was observed using spectrophotometry. Analyses using HPLC and mass spectroscopy did not confirm the release of the antimicrobial peptide [W 6 ]Hylin a1 after 24 h. In addition, analysis of the release solution showed new compounds, indicating the degradation of the peptide by enzymes contained in the latex. Additionally, the release of a peptide with a shorter sequence (Ac-WAAAA) was evaluated, and degradation was not observed. These results showed that the use of NRL as solid matrices as delivery systems of peptide are sequence dependent and could to be evaluated for each sequence.

  17. A test trial irradiation of natural rubber latex on large scale for the production of examination gloves in a production scale

    International Nuclear Information System (INIS)

    Devendra, R.; Kulatunge, S.; Chandralal, H.N.K.K.; Kalyani, N.M.V.; Seneviratne, J.; Wellage, S.

    1996-01-01

    Radiation Vulcanization of natural rubber latex has been developed extensively through various research and development programme. During these investigations many data was collected and from these data it was proved that radiation vulcanized natural rubber latex (RVNRL) can be used as a new material for industry (RVNRL symposium 1989; Makuuchi IAEA report). This material has been extensively tested in making of dipped goods and extruded products. However these investigations were confined only to laboratory experiments and these experiments mainly reflected material properties of RVNRL and only a little was observed about its behavior in actual production scale operation. The present exercise was carried out mainly to study the behavior of the material in production scale by irradiating latex on a large scale and producing gloves in a production scale plant. It was found that RVNRL can be used in conventional glove plants without making major alteration to the plant. Quality of the gloves that were produced using RVNRL is acceptable. It was also found that the small deviation of vulcanization dose will affect the crosslinking density of films. This will drastically reduce the tensile strength of the film. Crosslinking density or pre-vulcanized relax modulus (PRM) at 100% is a reliable property to control the pre vulcanization of latex by radiation

  18. Type I allergy to natural rubber latex and type IV allergy to rubber chemicals in health care workers with glove-related skin symptoms.

    Science.gov (United States)

    Nettis, E; Assennato, G; Ferrannini, A; Tursi, A

    2002-03-01

    It has been established that there are type I and type IV allergens in latex gloves. The purpose of the study was to establish the prevalence of rubber glove-induced skin symptoms among health care workers in one Italian hospital. Health care workers (n = 1584) were evaluated using a written questionnaire and 295 respondents with glove-induced skin symptoms were tested. We performed: skin prick test with latex glove extract and commercial latex, and environmental and food allergens; glove use test; patch tests with a rubber additive series; and RASTs. Hospital employees who used or had used latex gloves at work were 1294. Three hundred and sixteen (24.4%) reported glove-induced symptoms, namely, cutaneous symptoms in all the cases and non-cutaneous symptoms in 105 subjects (8.1%). Twenty-seven of the 295 symptomatic employees tested (9.1%) were latex sensitive. Thirty-one patients (10.5%) exhibited positive patch test to rubber-related allergens. The most positive readings were obtained from the Thiuram mix and the Carba mix, with 12 and 9 positivities, respectively. The risk factors for latex skin sensitization were: a previous history of atopy and asthma; history of surgery; pre-existing hand dermatitis; work-related symptoms; and positive skin tests to common inhalant and certain foods (P skin complaints of latex gloves are related to skin irritation rather than to allergy. The immediate allergy to latex and the delayed allergy to rubber chemicals suggest that all the health care workers with glove-related dermatitis should undergo both skin prick test and glove use test to detect type I hypersensitivity to latex, and patch test to detect type IV hypersensitivity to rubber chemicals.

  19. Cost evaluation of radiation vulcanization of natural rubber latex

    International Nuclear Information System (INIS)

    Makuuchi, K.

    2003-01-01

    Cost of radiation vulcanized NR latex was evaluated. The plant would be built in an existing dipping factory in an industrial area in a Southeast Asian country. One thousands dry tons of NR latex are vulcanized with a low energy electron accelerator. The electron accelerator is a self-shielding low energy type. The maximum accelerating voltage is 300 kV and the output power is 10 kW. The total construction cost of the plant is $400,000 including electron accelerator and other equipments. Costs of raw materials and utilities are $1.165 and $0.023 per one kg of product, respectively. The fixed costs of the plant consist of labor costs, labor overhead, maintenance, plant overhead, depreciation, and bank interest. It is $0.190/kg of product. The company overhead for operation including company management, R and D and insurance is $0.044/kg of product. Thus, the total production cost is estimated to be $1.422/kg of product. (author)

  20. Combination of Tung oil and Natural Rubber Latex in PVA as Water Based Coatings for Paperboard Application

    Directory of Open Access Journals (Sweden)

    Jianprasert Apichaya

    2015-01-01

    Full Text Available This research is focused on the preparation of the PVA/TO/NRL coatings for paperboard by using poly(vinyl alcohol (PVA as substance and blending with Tung oil (TO and/or natural rubber latex (NRL in order to enhance water resistance and dynamic mechanical properties. The effects of TO: NRL ratios on the structures were investigated by water resistance property and dynamic mechanical thermal analysis (DMA. The results showed that the water resistance property was improved by crosslinking of TO and film forming of NRL. The PVA/TO/NRL coating containing both TO and NRL gave better thermal behavior than those with only TO or NRL. For paperboard application, the PVA/TO/NRL coatings were applied on the paperboard to study water affinity and absorption rate on the coated surface. The rate of contact angle change of water on coated paperboards decreased depending on the ratios of TO and NRL.

  1. Euphorbia latex: a possible source of hydrocarbons and rubber

    Energy Technology Data Exchange (ETDEWEB)

    Viaud, P; Teisseire, D

    1975-01-01

    Illustrated descriptions are given of 36 plants of potential economic value in underdeveloped tropical countries, classified by use. The plants are either wild or cultivated on a fairly local scale. Accounts of limitations and special requirements and lists of references, research contacts and sources of germ plasm are included for each species. The following tree and shrub species are included: Cnidoscolus aconitifolius, C. chayamansa and hearts of several edible palm species including Euterpe edulis (vegetables); Durio species, Garcinia mangostana, Solanum quitoense, Bactris gaspiaes, Citrus grandis, Annona muricata and Pourouma cecropiaefolia (fruits); Orbignya martiana, Caryocar species, Jessenia polycarpa and Simmondsia chinensis (oil seeds); Acacia albida, Brosimum alicastrum, Cassia sturtii, Atriplex species and Prosopis tamarungo (forage (browse)); Mauritia flexuosa (fruit, wood, etc.); Euphorbia antisyphilitica (wax); and Parthenium argentatum (rubber).

  2. Rubber elongation factor (REF, a major allergen component in Hevea brasiliensis latex has amyloid properties.

    Directory of Open Access Journals (Sweden)

    Karine Berthelot

    Full Text Available REF (Hevb1 and SRPP (Hevb3 are two major components of Hevea brasiliensis latex, well known for their allergenic properties. They are obviously taking part in the biosynthesis of natural rubber, but their exact function is still unclear. They could be involved in defense/stress mechanisms after tapping or directly acting on the isoprenoid biosynthetic pathway. The structure of these two proteins is still not described. In this work, it was discovered that REF has amyloid properties, contrary to SRPP. We investigated their structure by CD, TEM, ATR-FTIR and WAXS and neatly showed the presence of β-sheet organized aggregates for REF, whereas SRPP mainly fold as a helical protein. Both proteins are highly hydrophobic but differ in their interaction with lipid monolayers used to mimic the monomembrane surrounding the rubber particles. Ellipsometry experiments showed that REF seems to penetrate deeply into the monolayer and SRPP only binds to the lipid surface. These results could therefore clarify the role of these two paralogous proteins in latex production, either in the coagulation of natural rubber or in stress-related responses. To our knowledge, this is the first report of an amyloid formed from a plant protein. This suggests also the presence of functional amyloid in the plant kingdom.

  3. Production Of Hollow Toy Product From Radiation Pre vulcanized Natural Rubber Latex (RVNRL) By Using Casting And Moulding Technique

    International Nuclear Information System (INIS)

    Mohd Noorwadi Mat Lazim; Sofian Ibrahim; Muhammad Saiful Omar

    2013-01-01

    Hollow toy products are very synonym to the child from the age of months since it able to stimulating each of their sense such as sight, hearing, taste, touch and smell. Most of hollow toy products are made from natural rubber latex by using moulding and casting technique. The moulding and casting technique is a manufacturing process by pored liquid latex into a mould, which contain cavity of the desired shape. The mould made from plaster of Paris able to absorbs water from latex meanwhile the presence of calcium ions from plaster of Paris will tend to diffuse into latex thus promote formation of deposit on surface of cavity mould. To improve the quality and safety of hollow toy product made from latex, Radiation Pre vulcanized Natural Rubber Latex (RVNRL) has been identified to be used because it can fulfill the standard requirement for latex and also due to its special abilities such as lower modulus (soft latex products), nitrosamines free, low in nitrosatables, free from chemical accelerators induced allergies and better biodegradability. This paper identify the problem appears from the process of making hollow toy products from RVNRL by using moulding and casting technique. (author)

  4. n-BA/KOH/t-BHP behaviour in the natural rubber latex vulcanization by gamma rays

    International Nuclear Information System (INIS)

    Souza, A. de.

    1994-01-01

    Natural rubber latex was vulcanized in the absence and in the presence of sensitizer (S), with gamma ray from 60 Co source, panoramic type, at the dose rate range of 1,20-1,33 kGy/h. The components of used S were n-butyl acrylate (n-BA), the KOH as stabilizer and t-butyl hydroperoxide (t-BHP) as co-S. The purpose of this work was to study the efficiency and the behaviour of each component of S in the irradiated latex crosslinking by tensile strength (T b ), volume fraction and permanent set. In the absence of S occur straight crosslinking between macromolecular adjacent radicals. IN the presence of S, the n-BA participates in the crosslinking through acrylic bridges between macromolecules. (author)

  5. Gloves against mineral oils and mechanical hazards: composites of carboxylated acrylonitrile-butadiene rubber latex.

    Science.gov (United States)

    Krzemińska, Sylwia; Rzymski, Władysław M; Malesa, Monika; Borkowska, Urszula; Oleksy, Mariusz

    2016-09-01

    Resistance to permeation of noxious chemical substances should be accompanied by resistance to mechanical factors because the glove material may be torn, cut or punctured in the workplace. This study reports on glove materials, protecting against mineral oils and mechanical hazards, made of carboxylated acrylonitrile-butadiene rubber (XNBR) latex. The obtained materials were characterized by a very high resistance of the produced materials to oil permeation (breakthrough time > 480 min). The mechanical properties, and especially tear resistance, of the studied materials were improved after the addition of modified bentonite (nanofiller) to the XNBR latex mixture. The nanocomposite meets the requirements in terms of parameters characterizing tear, abrasion, cut and puncture resistance. Therefore, the developed material may be used for the production of multifunctional protective gloves.

  6. Gloves against mineral oils and mechanical hazards: composites of carboxylated acrylonitrile–butadiene rubber latex

    Science.gov (United States)

    Krzemińska, Sylwia; Rzymski, Władysław M.; Malesa, Monika; Borkowska, Urszula; Oleksy, Mariusz

    2016-01-01

    Resistance to permeation of noxious chemical substances should be accompanied by resistance to mechanical factors because the glove material may be torn, cut or punctured in the workplace. This study reports on glove materials, protecting against mineral oils and mechanical hazards, made of carboxylated acrylonitrile–butadiene rubber (XNBR) latex. The obtained materials were characterized by a very high resistance of the produced materials to oil permeation (breakthrough time > 480 min). The mechanical properties, and especially tear resistance, of the studied materials were improved after the addition of modified bentonite (nanofiller) to the XNBR latex mixture. The nanocomposite meets the requirements in terms of parameters characterizing tear, abrasion, cut and puncture resistance. Therefore, the developed material may be used for the production of multifunctional protective gloves. PMID:26757889

  7. A study of using polythiol compounds and 2-ethyl-hexyl-acrylate with carbon tetrachloride as sensitizers for radiation vulcanization of natural rubber latex

    International Nuclear Information System (INIS)

    Polsuksiri, C.

    1989-01-01

    Experiments on using 3 different compounds of polythiol and an acrylate as sensitizer for radiation vulcanization were conducted. It was found that 1,4 butane diol propane tris-3-mercapto propionate showed the tendency to be a good sensitizer. The tensile strength of the rubber film prepared from the irradiated latex was found to be 14 MPa at sensitizer concentration of 1 phr and radiation dose of 45 kGy. As for 2-ethyl hexyl acrylate (2EHA), the maximum tensile strength of rubber film was found to be 23 MPa at concentration of 3 phr and radiation dose of 35 kGy. The mixture of 2 EHA and CCl 4 at various ratio was also used as sensitizer. The optimum ratio was found to be 5:1 at concentration of 6 phr and radiation dose of 15 kGy. The maximum tensile strength was as high as 25 MPa. The study also revealed that the radiation vulcanized latex with crosslink density of about 18x10 18 C.L./cm 3 would give the rubber film of highest tensile strength

  8. The influence of radiolytic sensitizers in natural rubber latex vulcanization induced by ionizing radiation

    International Nuclear Information System (INIS)

    Guedes, S.M.L.; Souza, A. de

    1991-01-01

    This work made on radiation vulcanization of natural rubber latex process by gamma rays from 60 Co source and electron beam of 1.5 MeV, 25 m A by Dynamitron, instead of classic process using sulfur. The experiment was carried out to study the influence of sensitizers (C Cl 4 and n-butyl acrylate) and was reported the vulcanization dose for each sensitizers, related to maximum tensile strength. The results show the possibility to introduce the volatile sensitizer (n-butyl acrylate) instead of C Cl 4 (toxic) in industry applications. (author)

  9. Surgical gloves fabrication using natural rubber latex vulcanized with gamma radiation

    International Nuclear Information System (INIS)

    Collantes, Hugo David Chirinos.

    1995-01-01

    Surgical gloves were manufactured by immersion coagulant method from vulcanized natural rubber latex by gamma rays at dose of 10 kGy in the air, at room temperature, using the following sensitizer vulcanization An-B 3 phr/KOH 0.2 phr. The influence of the parameter in the thickness of the surgical gloves manufacture, studied through fractional factorial designs technic, can be resumed by empirical linear correlation: y = 0.213 + 0.025 [Ca Cl 2 ] + 0.019 t. (author). 49 refs., 13 figs., 31 tabs

  10. Modification of Iraqi Asphalt 40/50 Properties Using Saw Dust (SD and Natural Rubber Latex

    Directory of Open Access Journals (Sweden)

    Rusul l M. Darwesh

    2018-04-01

    Full Text Available The aim of this research is to enhance the fundamental properties for asphalt binder as those spec-ifications relate to performance of asphalt mixtures. In this paper studied the effect of add (2, 4 % SD in different sizes and (3, 5 and 7% Natural rubber latex to the straight asphalt 40/50 produced from Al-Dura refinery at 160C, it was added each additive separately and then added together to asphalt in same temperature, then tested physically and mechanically according to the American Society for Testing and Materials (ASTM, the result showed largely improvement.

  11. Preparation of Low Allergenic Protein Concentrated Natural Rubber Latex Using Suitable Low Molecular Weight Cellulose Derivatives Induced by Gamma Irradiation

    International Nuclear Information System (INIS)

    Siri-Upathum, Chyagrit; Boonyawat, Jariya

    2007-08-01

    Full text: Low molecular weight carboxy methyl cellulose (CMC), hydroxyl ethyl cellulose (HEC), hydroxyl propyl cellulose (HPC) and methyl cellulose (MC) prepared by radiation-induced degradation were added into diluted natural concentrated latex prior to centrifuge for a purpose of reducing allergenic rubber protein in the latex. Optimum molecular weight (Mv) of CMC and HEC for such a purpose was found to be 17-18 kDa which decreased allergenic rubber protein (14-94 kDa) to an undetectable amount as determined by SDS PAGE method

  12. Comparative Proteomics of Rubber Latex Revealed Multiple Protein Species of REF/SRPP Family Respond Diversely to Ethylene Stimulation among Different Rubber Tree Clones

    Directory of Open Access Journals (Sweden)

    Zheng Tong

    2017-05-01

    Full Text Available Rubber elongation factor (REF and small rubber particle protein (SRPP are two key factors for natural rubber biosynthesis. To further understand the roles of these proteins in rubber formation, six different genes for latex abundant REF or SRPP proteins, including REF138,175,258 and SRPP117,204,243, were characterized from Hevea brasiliensis Reyan (RY 7-33-97. Sequence analysis showed that REFs have a variable and long N-terminal, whereas SRPPs have a variable and long C-terminal beyond the REF domain, and REF258 has a β subunit of ATPase in its N-terminal. Through two-dimensional electrophoresis (2-DE, each REF/SRPP protein was separated into multiple protein spots on 2-DE gels, indicating they have multiple protein species. The abundance of REF/SRPP proteins was compared between ethylene and control treatments or among rubber tree clones with different levels of latex productivity by analyzing 2-DE gels. The total abundance of each REF/SRPP protein decreased or changed a little upon ethylene stimulation, whereas the abundance of multiple protein species of the same REF/SRPP changed diversely. Among the three rubber tree clones, the abundance of the protein species also differed significantly. Especially, two protein species of REF175 or REF258 were ethylene-responsive only in the high latex productivity clone RY 8-79 instead of in RY 7-33-97 and PR 107. Some individual protein species were positively related to ethylene stimulation and latex productivity. These results suggested that the specific protein species could be more important than others for rubber production and post-translational modifications might play important roles in rubber biosynthesis.

  13. Green synthesis of colloidal silver nanoparticles using natural rubber latex extracted from Hevea brasiliensis.

    Science.gov (United States)

    Guidelli, Eder José; Ramos, Ana Paula; Zaniquelli, Maria Elisabete D; Baffa, Oswaldo

    2011-11-01

    Colloidal silver nanoparticles were synthesized by an easy green method using thermal treatment of aqueous solutions of silver nitrate and natural rubber latex (NRL) extracted from Hevea brasiliensis. The UV-Vis spectra detected the characteristic surface plasmonic absorption band around 435 nm. Both NRL and AgNO(3) contents in the reaction medium have influence in the Ag nanoparticles formation. Lower AgNO(3) concentration led to decreased particle size. The silver nanoparticles presented diameters ranging from 2 nm to 100 nm and had spherical shape. The selected area electron diffraction (SAED) patterns indicated that the silver nanoparticles have face centered cubic (fcc) crystalline structure. FTIR spectra suggest that reduction of the silver ions are facilitated by their interaction with the amine groups from ammonia, which is used for conservation of the NRL, whereas the stability of the particles results from cis-isoprene binding onto the surface of nanoparticles. Therefore natural rubber latex extracted from H. brasiliensis can be employed in the preparation of stable aqueous dispersions of silver nanoparticles acting as a dispersing and/or capping agent. Moreover, this work provides a new method for the synthesis of silver nanoparticles that is simple, easy to perform, pollutant free and inexpensive. Copyright © 2011 Elsevier B.V. All rights reserved.

  14. Properties and Characterization of Kenaf-Filled Natural Rubber Latex Foam

    Directory of Open Access Journals (Sweden)

    Ahmad Fikri Abdul Karim

    2015-12-01

    Full Text Available Kenaf powder was incorporated with natural rubber latex (NRL compound and foamed to make natural rubber latex foam (NRLF by using a well known technique called the Dunlop method. Different loadings of kenaf powder were added to NRL compound and was foamed to make NRLF. The mechanical properties, density, compression, thermal, and micro-structural characterization of control NRLF and kenaf incorporated NRLF were studied. Increasing content of kenaf reduced the tensile strength, elongation at break, and compressive strength of a NRLF. Modulus at 100% elongation and density of the NRLF increased with an increase in filler loading. Higher kenaf loading indicated higher elasticity of kenaf-filled NRLF, but the recovery percentage of kenaf-filled NRLF decreased with increasing kenaf loading. From thermogravimetric analysis (TGA result, an increase in the amount of kenaf loading from 1 to 7 phr increased the thermal stability of kenaf-filled NRLF. Morphological and micro-structural characterization performed by using scanning electron microscopy (SEM showed that kenaf powder filled up the micro-sized pores in the open cell structure of kenaf-filled NRLF.

  15. Content of Asthmagen Natural Rubber Latex Allergens in Commercial Disposable Gloves.

    Science.gov (United States)

    Bittner, C; Garrido, M V; Krach, L H; Harth, V

    The use of natural rubber latex (NRL) gloves in many occupations may lead to latex sensitization, allergic asthma, and skin reactions. Due to their good properties and environmental safety NRL gloves are still being used in the healthcare setting, but also in the food industry, by hairdressers, cleaners, etc. The aim of our study was to assess the protein and NRL allergen content in commercial gloves by different methods, including a new assay. Twenty commercially available NRL gloves were analyzed. Protein extraction was performed according to the international standard ASTM D-5712. Total protein content was measured with a modified Lowry method, NRL content with the CAP Inhibition Assay, the Beezhold ELISA Inhibition Assay, and an innovative ELISA with IgY-antibodies extracted from eggs of NRL-immunized hens (IgY Inhibition Assay). We found a high protein content in a range of 215.0-1304.7 μg/g in 8 out of the 20 NRL gloves. Seven of the 20 gloves were powdered, four of them with a high protein content. In gloves with high protein content, the immunological tests detected congruently high levels of NRL allergen. We conclude that a high percentage of commercially available NRL gloves still represent a risk for NRL allergy, including asthma. The modified Lowry Method allows to infer on the latex allergen content.

  16. Irradiation grafting of natural rubber latex with maleic anhydride and its compatibilization of poly(lactic acid)/natural rubber blends

    Science.gov (United States)

    Pongsathit, Siriwan; Pattamaprom, Cattaleeya

    2018-03-01

    Maleic anhydride (MA) is an interesting monomer to be grafted onto natural rubber(NR) due to its potential as a compatibilizer of hydrophobic rubbers and polymers with higher polarity. So far, radiation grafting of MA onto NR in latex state has not been reported. In this study, the grafting of NR with MA in latex state was investigated by exposing the latex to cobalt-60 gamma irradiation at a fixed MA content of 9% and a varied absorbed doses from 2 to 10 kGy. The FTIR spectrometer, 1H NMR spectrometer and gel content analysis have confirmed successful grafting of MA onto NR after irradiation. The grafted NRs were then used to increase the compatibility and the impact property of PLA/NR blends. It was found that the highest impact strength of the blends was achieved when the grafting was carried out at the absorbed dose of 4 kGy.

  17. Antifungal activity of fluconazole-loaded natural rubber latex against Candida albicans.

    Science.gov (United States)

    Yonashiro Marcelino, Mônica; Azevedo Borges, Felipe; Martins Costa, Ana Flávia; de Lacorte Singulani, Junya; Ribeiro, Nathan Vinícius; Barcelos Costa-Orlandi, Caroline; Garms, Bruna Cambraia; Soares Mendes-Giannini, Maria José; Herculano, Rondinelli Donizetti; Fusco-Almeida, Ana Marisa

    2018-03-01

    This work aimed to produce a membrane based on fluconazole-loaded natural rubber latex (NRL), and study their interaction, drug release and antifungal susceptibility against Candida albicans. Fluconazole-loaded NRL membrane was obtained by casting method. The Fourier Transform Infrared Spectroscopy showed no modifications either in NRL or fluconazole after the incorporation. Mechanical test presented low Young's modulus and high strain, indicating the membranes have sufficient elasticity for biomedical application. The bio-membrane was able to release the drug and inhibit the growth of C. albicans as demonstrated by disk diffusion and macrodilution assays. The biomembrane was able to release fluconazole and inhibit the growth of C. albicans, representing a promising biomaterial for skin application.

  18. Formation of protein complex with the aid of polyethylene glycol for deproteinized natural rubber latex

    Science.gov (United States)

    Wei, Lim Keuw; Ing, Wong Kwee; Badri, Khairiah Haji; Ban, Wong Chong

    2013-11-01

    The effect of polyethylene glycol (PEG) as a deproteinizing agent in commercial natural rubber latex (NRL) onto the physicochemical properties of the NRL was investigated. Three types of PEG were used namely PEG200, PEG4000 and PEG20000 (molecular weight of 200, 4000 and 20000 g/mol respectively). The optimum amount of PEG in NRL was determined from viscosity changes, protein content and Fourier Transform Infrared spectroscopy. Level of protein reduction was affected by molecular weight of PEG. The addition of PEG in NRL reduced the protein content of NRL (3.30 %) to the lowest (2.01 %) at 0.40 phr of PEG200 due to more attractive hydrophobic interactions between short chains PEG compared to PEG4000 (2.24%) and PEG20000 (2.15%). This was verified through FTIR spectroscopy analysis by observing the primary and secondary amide peak where PEG4000 has lesser absorption at the region compared to with PEG20000.

  19. Diclofenac Potassium Transdermal Patches Using Natural Rubber Latex Biomembranes as Carrier

    Directory of Open Access Journals (Sweden)

    Natan Roberto de Barros

    2015-01-01

    Full Text Available The aim of this study was to design a compound transdermal patch containing diclofenac potassium (Dic-K using natural rubber latex (NRL biomembrane. The NRL from Hevea brasiliensis is easily manipulated and low cost and presents high mechanical resistance. It is a biocompatible material which can stimulate natural angiogenesis and is capable of adhering cells on its surface. Recent researches have used the NRL for Transdermal Drug Delivery Systems (TDDSs. Dic-K is used for the treatment of rheumatoid arthritis and osteoarthritis and pain relief for postoperative and posttraumatic cases, as well as inflammation and edema. Results showed that the biomembrane can release Dic-K for up to 216 hours. The kinetics of the Dic-K release could be fitted with double exponential function. X-ray diffraction and Fourier Transform Infrared (FTIR spectroscopy show some interaction by hydrogen bound. The results indicated the potential of the compound patch.

  20. Characteristic of natural rubber latex-methyl metha-crylate copolymer in mineral lubricant base oil

    International Nuclear Information System (INIS)

    Meri Suhartini; Rahmawati

    2010-01-01

    Natural rubber latex-methyl methacrylate copolymer was diluted in xylene, then diluted in four types of lubricant base oil with concentrations of 0.25%, 1%, 5%, and 10%. The mixed solutions were analyzed to obtain kinematics viscosity, viscosity index, density, ash content, metal content, flash point, shear stability and total alkali number. The viscosity index of sample, increased by adding the copolymer solution. The results showed that lubricant base oil of High Viscosity index (HVI) 60 and mixed HVI 60: HVI 650 gave optimum viscosity index. The higher concentration of polymer added into base lubricant oil, the higher viscosity index obtained. The shear stability test showed that the kinematics viscosity of sample decreased 6.5% after 60 minutes of treatment test. (author)

  1. Properties of natural rubber/attapulgite composites prepared by latex compounding method: Effect of filler loading

    International Nuclear Information System (INIS)

    Muttalib, Siti Nadzirah Abdul; Othman, Nadras; Ismail, Hanafi

    2015-01-01

    This paper reports on the effect of filler loading on properties of natural rubber (NR)/attapulgite (ATP) composites. The NR/ATP composites were prepared by latex compounding method. It is called as masterbatch. The masterbatch was subsequently added to the NR through melt mixing process. The vulcanized NR/ATP composites were subjected to mechanical, swelling and morphological tests. All the results were compared with NR/ATP composites prepared by conventional system. The composites from masterbatch method showed better results compared to composites prepared by conventional method. They have higher tensile properties, elongation at break and tear strength. The images captured through scanning electron microscopy test revealed the improvement of tensile strength in masterbatch NR/ATP composites. It can be seen clearly that masterbatch NR/ATP have better filler dispersion compared to conventional method NR/ATP composites

  2. Properties of natural rubber/attapulgite composites prepared by latex compounding method: Effect of filler loading

    Energy Technology Data Exchange (ETDEWEB)

    Muttalib, Siti Nadzirah Abdul, E-mail: sitinadzirah.amn@gmail.com; Othman, Nadras, E-mail: srnadras@usm.my; Ismail, Hanafi, E-mail: ihanafi@usm.my [School of Materials and Mineral Resources Engineering, Engineering Campus, Universiti Sains Malaysia, Seri Ampangan, 14300 Nibong Tebal, Pulau Pinang (Malaysia)

    2015-07-22

    This paper reports on the effect of filler loading on properties of natural rubber (NR)/attapulgite (ATP) composites. The NR/ATP composites were prepared by latex compounding method. It is called as masterbatch. The masterbatch was subsequently added to the NR through melt mixing process. The vulcanized NR/ATP composites were subjected to mechanical, swelling and morphological tests. All the results were compared with NR/ATP composites prepared by conventional system. The composites from masterbatch method showed better results compared to composites prepared by conventional method. They have higher tensile properties, elongation at break and tear strength. The images captured through scanning electron microscopy test revealed the improvement of tensile strength in masterbatch NR/ATP composites. It can be seen clearly that masterbatch NR/ATP have better filler dispersion compared to conventional method NR/ATP composites.

  3. Finite Element Analysis of Simple Rectangular Microstrip Sensor for Determination Moisture Content of Hevea Rubber Latex

    Science.gov (United States)

    Yahaya, NZ; Ramli, MR; Razak, NNANA; Abbas, Z.

    2018-04-01

    The Finite Element Method, FEM has been successfully used to model a simple rectangular microstrip sensor to determine the moisture content of Hevea rubber latex. The FEM simulation of sensor and samples was implemented by using COMSOL Multiphysics software. The simulation includes the calculation of magnitude and phase of reflection coefficient and was compared to analytical method. The results show a good agreement in finding the magnitude and phase of reflection coefficient when compared with analytical results. Field distributions of both the unloaded sensor as well as the sensor loaded with different percentages of moisture content were visualized using FEM in conjunction with COMSOL software. The higher the amount of moisture content in the sample the more the electric loops were observed.

  4. Natural rubber latex used as drug delivery system in guided bone regeneration (GBR

    Directory of Open Access Journals (Sweden)

    Rondinelli Donizetti Herculano

    2009-06-01

    Full Text Available In this work, we propose natural rubber latex (NRL membranes as a protein delivery system. For this purpose Bovine Serum Albumin (BSA was incorporated into the latex solution for in vitro protein delivery experiments. Different polymerization temperatures were used, from -10 to 27 °C, in order to control the membrane morphology. These membranes were characterized by Scanning Electron Microscopy (SEM, Atomic Force Microscopy (AFM, as well as the Lowry Method to measure the BSA release. SEM and AFM microscopy analysis showed that the number, size and distribution of pores in NRL membranes can be varied, as well as its overall morphology. We have found that the morphology of the membrane is the predominant factor for higher protein release, compared with pore size and number of pores. Results demonstrated that the best drug-delivery system was the membrane polymerized at RT (27 °C, which does release 66% of its BSA content for up to 18 days. Our results indicate that NRLb could be used in the future as an active membrane that could accelerate bone healing in GBR.

  5. Comparative Transcriptome Analysis of Latex Reveals Molecular Mechanisms Underlying Increased Rubber Yield in Hevea brasiliensis Self-Rooting Juvenile Clones.

    Science.gov (United States)

    Li, Hui-Liang; Guo, Dong; Zhu, Jia-Hong; Wang, Ying; Chen, Xiong-Ting; Peng, Shi-Qing

    2016-01-01

    Rubber tree (Hevea brasiliensis) self-rooting juvenile clones (JCs) are promising planting materials for rubber production. In a comparative trial between self-rooting JCs and donor clones (DCs), self-rooting JCs exhibited better performance in rubber yield. To study the molecular mechanism associated with higher rubber yield in self-rooting JCs, we sequenced and comparatively analyzed the latex of rubber tree self-rooting JCs and DCs at the transcriptome level. Total raw reads of 34,632,012 and 35,913,020 bp were obtained from the library of self-rooting JCs and DCs, respectively, by using Illumina HiSeq 2000 sequencing technology. De novo assemblies yielded 54689 unigenes from the library of self-rooting JCs and DCs. Among 54689 genes, 1716 genes were identified as differentially expressed between self-rooting JCs and DCs via comparative transcript profiling. Functional analysis showed that the genes related to the mass of categories were differentially enriched between the two clones. Several genes involved in carbohydrate metabolism, hormone metabolism and reactive oxygen species scavenging were up-regulated in self-rooting JCs, suggesting that the self-rooting JCs provide sufficient molecular basis for the increased rubber yielding, especially in the aspects of improved latex metabolisms and latex flow. Some genes encoding epigenetic modification enzymes were also differentially expressed between self-rooting JCs and DCs. Epigenetic modifications may lead to gene differential expression between self-rooting JCs and DCs. These data will provide new cues to understand the molecular mechanism underlying the improved rubber yield of H. brasiliensis self-rooting clones.

  6. The Effect of Paraffin Wax to Properties of Radiation Vulcanization Natural Rubber Latex (RVNRL)

    International Nuclear Information System (INIS)

    Mohd Noorwadi Mat Lazim; Sofian Ibrahim; Muhammad Saiful Omar

    2015-01-01

    Dipping factories often encounter a serious problem with high tackiness of the finish products during storage. The tackiness effect can be lead to rejection of products. This tackiness effect of natural (NR) rubber film originates in the free rubber chain ends at the surface of the film. The tackiness is not depends on the degree of crosslinking (vulcanization), since radiation itself unable to reduce the tackiness effect. The RVNRL requires addition of additive or anti-tack agent into formulation to reduce tackiness effect. In this experiment, paraffin wax manufactured by Emulco Sdn Bhd under the trade name Aquawax 48 was added into RVNRL formulation as anti-tack and the effect of paraffin wax to physical and mechanical properties of RVNRL was study. (author)

  7. Rubber particle proteins REF1 and SRPP1 interact differently with native lipids extracted from Hevea brasiliensis latex.

    Science.gov (United States)

    Wadeesirisak, Kanthida; Castano, Sabine; Berthelot, Karine; Vaysse, Laurent; Bonfils, Frédéric; Peruch, Frédéric; Rattanaporn, Kittipong; Liengprayoon, Siriluck; Lecomte, Sophie; Bottier, Céline

    2017-02-01

    Rubber particle membranes from the Hevea latex contain predominantly two proteins, REF1 and SRPP1 involved in poly(cis-1,4-isoprene) synthesis or rubber quality. The repartition of both proteins on the small or large rubber particles seems to differ, but their role in the irreversible coagulation of the rubber particle is still unknown. In this study we highlighted the different modes of interactions of both recombinant proteins with different classes of lipids extracted from Hevea brasiliensis latex, and defined as phospholipids (PL), glycolipids (GL) and neutral lipids (NL). We combined two biophysical methods, polarization modulated-infrared reflection adsorption spectroscopy (PM-IRRAS) and ellipsometry to elucidate their interactions with monolayers of each class of lipids. REF1 and SRPP1 interactions with native lipids are clearly different; SRPP1 interacts mostly in surface with PL, GL or NL, without modification of its structure. In contrast REF1 inserts deeply in the lipid monolayers with all lipid classes. With NL, REF1 is even able to switch from α-helice conformation to β-sheet structure, as in its aggregated form (amyloid form). Interaction between REF1 and NL may therefore have a specific role in the irreversible coagulation of rubber particles. Copyright © 2016 Elsevier B.V. All rights reserved.

  8. Effect of filling surface-treated pyrolytic char on resistivity of rubber films

    Directory of Open Access Journals (Sweden)

    Pattraporn Yamkaya

    2015-03-01

    Full Text Available In this research, natural rubber (NR films filled with pyrolytic tire char, carbon black N234 and N330 were compared for their electrical resistivity. The filler loading was varied to be 5, 10, 15, 20 and 25% of dry rubber content. The effect of surfactant which is 2 %w/v sodium dodecyl sulfate (SDS was also investigated. In the experiments, it was necessary to disperse the pyrolytic char in ethyl alcohol while disperse carbon black (CB in ammonium hydroxide solution prior to mixing with the rubber latex and the filled NR film was prepared by casting the mixture on a plate. It was found that increasing the amount of pyrolytic char in the NR film could lower its resistivity. The surfactant, SDS, could help better dispersion of both CB and pyrolytic char, thereby decreasing the resistivity. In a separate experiment where hexane vapor was absorbed in NR film without surfactant, in the first 30 seconds, the rate of increasing resistivity of the CB-filled film was not seen as clearly as that of pyrolytic-char-filled film. For the films with surfactant, the slow increase in resistivity of the NR films filled with N330 and pyrolytic char during adsorbing hexane vapor was observed.

  9. Latex stage blending of multiwalled carbon nanotube in carboxylated acrylonitrile butadiene rubber: Mechanical and electrical properties

    International Nuclear Information System (INIS)

    Preetha Nair, K.; Thomas, Paulbert; Joseph, Rani

    2012-01-01

    Highlights: ► MWCNT can act as a reinforcing filler in XNBR at very low concentration. ► SEM and XRD analysis confirm uniform distribution of nanotube in the matrix. ► Mechanical properties showed considerable improvement. ► Thermal stability of the composite is marginally improved. -- Abstract: Multiwalled carbon nanotube (MWCNT) was dispersed in sodium dodecyl benzene sulphonate (SDBS) by sonication. The dispersed MWCNT (0.05–0.3 gm) was incorporated in carboxylated acrylonitrile butadiene rubber (XNBR) latex. Mechanical, electrical and thermal properties of these composites were studied. Mechanical properties of the composites increased up to an optimum concentration and then decreased. Dielectric properties of the composites were studied in the S band (frequency range 2–4 GHz) by Cavity Perturbation method. Direct current (DC) electrical conductivity shows a percolation behaviour and conductivity increased by about 10 orders of magnitude. Thermal studies were conducted using Differential Scanning Calorimetry (DSC) and Thermo Gravimetric Analysis (TGA). As expected with the very small concentration of multiwalled carbon nanotube, glass transition temperature (T g ) and thermal stability of the composite showed a marginal increase. Composites were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD) and Scanning electron microscope (SEM) analysis.

  10. RoxB Is a Novel Type of Rubber Oxygenase That Combines Properties of Rubber Oxygenase RoxA and Latex Clearing Protein (Lcp).

    Science.gov (United States)

    Birke, Jakob; Röther, Wolf; Jendrossek, Dieter

    2017-07-15

    Only two types of rubber oxygenases, rubber oxygenase (RoxA) and latex clearing protein (Lcp), have been described so far. RoxA proteins (RoxAs) are c -type cytochromes of ≈70 kDa produced by Gram-negative rubber-degrading bacteria, and they cleave polyisoprene into 12-oxo-4,8-dimethyltrideca-4,8-diene-1-al (ODTD), a C 15 oligo-isoprenoid, as the major end product. Lcps are common among Gram-positive rubber degraders and do not share amino acid sequence similarities with RoxAs. Furthermore, Lcps have much smaller molecular masses (≈40 kDa), are b -type cytochromes, and cleave polyisoprene to a mixture of C 20 , C 25 , C 30 , and higher oligo-isoprenoids as end products. In this article, we purified a new type of rubber oxygenase, RoxB Xsp (RoxB of Xanthomonas sp. strain 35Y). RoxB Xsp is distantly related to RoxAs and resembles RoxAs with respect to molecular mass (70.3 kDa for mature protein) and cofactor content (2 c -type hemes). However, RoxB Xsp differs from all currently known RoxAs in having a distinctive product spectrum of C 20 , C 25 , C 30 , and higher oligo-isoprenoids that has been observed only for Lcps so far. Purified RoxB Xsp revealed the highest specific activity of 4.5 U/mg (at 23°C) of all currently known rubber oxygenases and exerts a synergistic effect on the efficiency of polyisoprene cleavage by RoxA Xsp RoxB homologs were identified in several other Gram-negative rubber-degrading species, pointing to a prominent function of RoxB for the biodegradation of rubber in Gram-negative bacteria. IMPORTANCE The enzymatic cleavage of rubber (polyisoprene) is of high environmental importance given that enormous amounts of rubber waste materials are permanently released (e.g., by abrasion of tires). Research from the last decade has discovered rubber oxygenase A, RoxA, and latex clearing protein (Lcp) as being responsible for the primary enzymatic attack on the hydrophobic and water-insoluble biopolymer poly( cis -1,4-isoprene) in Gram

  11. Formation of Defect-Free Latex Films on Porous Fiber Supports

    KAUST Repository

    Lively, Ryan P.; Mysona, Joshua A.; Chance, Ronald R.; Koros, William J.

    2011-01-01

    a defect-free lumen-side barrier layer can be created. Film experiments examined the effect of drying rate, latex age, substrate porosity (porous vs nonporous), and substrate hydrophobicity/ hydrophilicity. Film studies show that in ideal conditions

  12. Soybean oil in water-borne coatings and latex film formation study by AC impedance

    Science.gov (United States)

    Jiratumnukul, Nantana

    Conventional coalescing agents such as butyl cellosolve, butyl carbitol, and TexanolRTM are widely use in the latex coatings industry to facilitate film formation at ambient temperature. Coalescent aids are composed of solvents with low evaporation rates. After water evaporates, coalescent aids would help soften polymer molecules and form continuous films, then gradually evaporates from the film. Coalescent aids, therefore, are considered as volatile organic compounds (VOC), which are of environmental concern. The main purpose of this research project was to prepare a fatty acid glycol ester from soybean oil and glycol (polyols). The soybean oil glycol ester can be used as a coalescent aid in latex paint formulation. The soybean oil glycol ester not only lowered the minimum film formation temperature of latex polymers and continuous film formed at ambient temperature, but also after it has facilitated film formation, does not substantially evaporate, but becomes part of the film. Soybean oil glycol esters, therefore, can reduce the VOC levels and facilitate film formation of latex paints. In the second part of this research AC-Impedance was used to investigate the efficiency of soybean oil coalescent aid in latex film formation relative to the conventional ones. The coating resistance showed that the efficiency of film formation was increased as a function of dry time. The coating resistance also exhibited the effect of soybean oil ester in latex film formation in the same fashion as a conventional coalescent aid, TexanolRTM.

  13. Molecular identification and characterization of the pyruvate decarboxylase gene family associated with latex regeneration and stress response in rubber tree.

    Science.gov (United States)

    Long, Xiangyu; He, Bin; Wang, Chuang; Fang, Yongjun; Qi, Jiyan; Tang, Chaorong

    2015-02-01

    In plants, ethanolic fermentation occurs not only under anaerobic conditions but also under aerobic conditions, and involves carbohydrate and energy metabolism. Pyruvate decarboxylase (PDC) is the first and the key enzyme of ethanolic fermentation, which branches off the main glycolytic pathway at pyruvate. Here, four PDC genes were isolated and identified in a rubber tree, and the protein sequences they encode are very similar. The expression patterns of HbPDC4 correlated well with tapping-simulated rubber productivity in virgin rubber trees, indicating it plays an important role in regulating glycometabolism during latex regeneration. HbPDC1, HbPDC2 and HbPDC3 had striking expressional responses in leaves and bark to drought, low temperature and high temperature stresses, indicating that the HbPDC genes are involve in self-protection and defense in response to various abiotic and biotic stresses during rubber tree growth and development. To understand ethanolic fermentation in rubber trees, it will be necessary to perform an in-depth study of the regulatory pathways controlling the HbPDCs in the future. Copyright © 2014 Elsevier Masson SAS. All rights reserved.

  14. Outcomes of a natural rubber latex control program in an Ontario teaching hospital.

    Science.gov (United States)

    Tarlo, S M; Easty, A; Eubanks, K; Parsons, C R; Min, F; Juvet, S; Liss, G M

    2001-10-01

    Allergy to natural rubber latex (NRL) has been frequently reported in health care workers. However, there is little published evidence of the outcome of hospital intervention programs to reduce exposure and detect cases of sensitization early. This study assesses the effects of intervention to reduce NRL allergy in an Ontario teaching hospital with approximately 8000 employees. A retrospective review assessed annual numbers of employees visiting the occupational health clinic, allergy clinic, or both for manifestations of NRL allergy compared with the timing of introduction of intervention strategies, such as worker education, voluntary medical surveillance, and hospital conversion to low-protein, powder-free NRL gloves. The number of workers identified with NRL allergy rose annually, from 1 in 1988 to 6 in 1993. When worker education and voluntary medical surveillance were introduced in 1994, a further 25 workers were identified. Nonsterile gloves were changed to low-protein, powder-free NRL gloves in 1995: Diagnoses fell to 8 workers that year, and 2 of the 3 nurses who had been off work because of asthma-anaphylaxis were able to return to work with personal avoidance of NRL products. With a change to lower protein, powder-free NRL sterile gloves in 1997, allergy diagnoses fell to 3, and only 1 new case was identified subsequently up to May 1999. No increased glove costs were incurred as a result of consolidated glove purchases. This program to reduce NRL allergy in employees was effectively achieved without additional glove costs while reducing expenses from time off work and workers' compensation claims.

  15. Evaluation of sodium diclofenac release using natural rubber latex as carrier

    International Nuclear Information System (INIS)

    Aielo, Patricia B.; Borges, Felipe A.; Romeira, Karoline M.; Herculano, Rondinelli D.; Miranda, Matheus Carlos Romeiro; Arruda, Larisa B. de; Lisboa Filho, Paulo Noronha; Drago, Bruno de C.

    2014-01-01

    Sodium Diclofenac is a non-steroidal anti-inflammatory drug (NSAID) taken to reduce inflammation and, as an analgesic, reduce pain. Although this drug is widely used in the general population, properties such as the short half-time and some side effects restrict its clinical use. The most common side effects are: gastric irritation, gastritis, peptic ulcer and bleeding. Studies involving biomaterials as carrier for drug release have been proving their efficiency in overcoming those problems and better controlling the release rate and targeting of the drug. Natural rubber latex (NRL) has been proven excellent for its biocompatibility and ability to stimulate angiogenesis, cellular adhesion and the formation of extracellular matrix, promoting the replacement and regeneration of tissue. In this work, a NRL membrane is used to deliver sodium diclofenac. Sodium diclofenac (NaDic) was found to be adsorbed on the NRL membrane, with little or no incorporation into the membrane bulk, according to energy dispersive Scanning Electron Microscopy with X-Ray microanalysis (SEM-EDS) spectroscopy. In addition, FT-IR shows that there is no molecular-level interaction between drug and NRL. Already, the X-Ray Diffraction (XRD) of NaDic-NRL shows a broader one spectrum than the sharper halo (amorphous characteristic XRD spectrum) of pure NRL. More importantly, the release time of diclofenac in a NRL membrane in vitro was increased from the typical 2-3 h for oral tablets to ca. 74 h. The kinetics of the drug release could be fitted with a double exponential function, with two characteristic times of 0.899 and 32.102 h. In this study, we demonstrated that the interesting properties provided by NRL membranes combined with a controlled release of drug is relevant for biomedical applications.(author)

  16. Evaluation of sodium diclofenac release using natural rubber latex as carrier

    Energy Technology Data Exchange (ETDEWEB)

    Aielo, Patricia B.; Borges, Felipe A.; Romeira, Karoline M.; Herculano, Rondinelli D., E-mail: rond@assis.unesp.br [Universidade Estadual Paulista Julio de Mesquita Filho (UNESP), Assis, SP (Brazil). Fac. de Ciencias e Letras. Dept. de Ciencias Biologicas; Miranda, Matheus Carlos Romeiro [Universidade Estadual Paulista Julio de Mesquita Filho (UNESP), Araraquara, SP (Brazil). Inst. de Quimica; Arruda, Larisa B. de; Lisboa Filho, Paulo Noronha; Drago, Bruno de C. [Universidade Estadual Paulista Julio de Mesquita Filho (UNESP), Bauru, SP (Brazil). Fac. de Ciencias. Dept. de Fisica

    2014-08-15

    Sodium Diclofenac is a non-steroidal anti-inflammatory drug (NSAID) taken to reduce inflammation and, as an analgesic, reduce pain. Although this drug is widely used in the general population, properties such as the short half-time and some side effects restrict its clinical use. The most common side effects are: gastric irritation, gastritis, peptic ulcer and bleeding. Studies involving biomaterials as carrier for drug release have been proving their efficiency in overcoming those problems and better controlling the release rate and targeting of the drug. Natural rubber latex (NRL) has been proven excellent for its biocompatibility and ability to stimulate angiogenesis, cellular adhesion and the formation of extracellular matrix, promoting the replacement and regeneration of tissue. In this work, a NRL membrane is used to deliver sodium diclofenac. Sodium diclofenac (NaDic) was found to be adsorbed on the NRL membrane, with little or no incorporation into the membrane bulk, according to energy dispersive Scanning Electron Microscopy with X-Ray microanalysis (SEM-EDS) spectroscopy. In addition, FT-IR shows that there is no molecular-level interaction between drug and NRL. Already, the X-Ray Diffraction (XRD) of NaDic-NRL shows a broader one spectrum than the sharper halo (amorphous characteristic XRD spectrum) of pure NRL. More importantly, the release time of diclofenac in a NRL membrane in vitro was increased from the typical 2-3 h for oral tablets to ca. 74 h. The kinetics of the drug release could be fitted with a double exponential function, with two characteristic times of 0.899 and 32.102 h. In this study, we demonstrated that the interesting properties provided by NRL membranes combined with a controlled release of drug is relevant for biomedical applications.(author)

  17. Mechanical and Physical Studies on Different Doses of Radiation Pre vulcanized Natural Rubber Latex (RVNRL)

    International Nuclear Information System (INIS)

    Syuhada Ramli; Sofian Ibrahim; Muhammad Saiful Omar; Mohd Noorwadi Mat Lazim; Khairul Hisyam Mohamed Yusof; Najib Mohammmad Zakey; Hafizuddin Maseri

    2014-01-01

    RVNRL mixture of 12 kGy (RVNRL12) and 25 kGy (RVNRL25) at different blending ratios were prepared by stirring the mixture using a magnetic stirrer RVNRL at a speed of 1-3 rpm overnight to get the dough consistency. RVNRL12 with RVNRL25 attendance at a ratio of 90:10, 80:20, 70:30, 60:40 and 50:50 investigated. The study of physical and mechanical properties of 12/ 25 blends RVNRL performed on film samples prepared by immersion method coagulant. RVNRL25 result of the addition of the mixture RVNRL12 showed an increase in tensile strength mixture ratio of 90:10 RVNRL12 / RVNRL25 and tensile strength are declining at a ratio higher RVNRL25 content. Increase the tensile strength was found to increase due to the impact of lower doses of dough RVNRL12 and RVNRL25. This shows that blending RVNRL lower doses help improve the physical properties of latex due to exposure dose exceeding the dose required RVNRL. (author)

  18. [Changes in the peripheral blood of workers engaged in ethylbenzene-styrene and synthetic rubber and latex manufacture].

    Science.gov (United States)

    Khristeva, V

    1986-01-01

    A total of 67 workers were examined from the production of "Ethyl benzene-styrene" and 184 workers from the production of "Synthetic rubber and latex", as well as a control group of 59 employees. The workers from the first production are exposed to the effect of styrene, ethyl benzene and toluene. The concentrations of the substances surpass MAC, with several times, at the majority of the working places. The workers with a length of service over 10 years predominate. The workers from the second production are exposed to the combined effect of styrene and divinyl, their concentrations fluctuating from 2 to 8 times over MAC. The workers with a length of service over 10 years are 71.7%. The deviations, established in the hematological indices studied are compared with the results from a study on the workers from those productions of 6 years ago. Dynamics in the changes was established among the workers from the production of "Synthetic rubber and latex", associated with the duration of occupational exposure to styrene and divinyl. In case of a shorter length of service, the deviations are functional (reduction of peroxidase activity in granulocytes), increase of hemoglobin and hematocrit, associated with the adaptive reaction of organism. Pronounced anemic syndrome was established in a considerable number (24 workers) after an exposure of 10 years as well as lymphocytosis (35 subjects) and leukopenia (9 subjects).

  19. Efficiency of 1,9- Nonane-diol-diacrylate as a radiation vulcanization accelerator for natural rubber latex

    International Nuclear Information System (INIS)

    Haque, M.E.

    2003-09-01

    The efficiency of 1,9- Nonane-diol-diacrylate (NDDA) as a radiation vulcanization accelerator (RVA) for natural rubber latex (NRL) was investigated. Both gamma rays and electron beam (EB) were used for vulcanizing NRL with NDDA. The radiation dose of gamma rays, concentration of NDDA required to vulcanize the latex were optimized. 20 kGy radiation dose of gamma rays and 5 phr concentration of NDDA were found optimum to get maximum tensile and related properties. NRL was vulcanized under EB to find out the optimum condition of irradiation with this RVA. The defoamer concentrations, length of irradiation time under EB, concentration of RVA were optimizer by changing various parameters of the EB machine with a constant set of the others. 0.2 phr defoamer concentration, 30 minutes irradiation time and 5 phr concentration of NDDA were found optimum for irradiation of NRL under the EB machine. Effect of low current and optimum volume of latex charged in the reaction vessel suitable for vulcanization at a time were found out. (author)

  20. Flexible diamond-like carbon film coated on rubber

    NARCIS (Netherlands)

    Pei, Y.T.; Bui, X.L.; Pal, J.P. van der; Martinez-Martinez, D.; Hosson, J.Th.M. De

    2013-01-01

    Dynamic rubber seals are major sources of friction of lubrication systems and bearings, which may take up to 70% of the total friction. The solution we present is to coat rubbers with diamond-like carbon (DLC) thin films by which the coefficient of friction is reduced to less than one tenth. Coating

  1. Physicomechanical properties of nanocomposites based on cellulose nanofibre and natural rubber latex

    CSIR Research Space (South Africa)

    Abraham, E

    2012-11-01

    Full Text Available and tensile strength was observed as a result of addition of CNF to the rubber matrix especially at higher CNF loading. DMA showed a change in the storage modulus of the rubber matrix upon addition of CNF which proves the reinforcing effect of CNF in the NR...

  2. Intercomparison of Methods for Determination of Resonant Frequency Shift of a Microstrip Patch Antenna Loaded with Hevea Rubber Latex

    Directory of Open Access Journals (Sweden)

    Nor Zakiah Yahaya

    2014-01-01

    Full Text Available This paper presents an intercomparison between the finite element method, method of moment, and the variational method to determine the effect of moisture content on the resonant frequency shift of a microstrip patch loaded with wet material. The samples selected for this study were Hevea rubber latex with different percentages of moisture content from 35% to 85%. The results were compared with the measurement data in the frequency range between 1 GHz and 4 GHz. It was found that the finite element method is the most accurate among all the three computational techniques with 0.1 mean error when compared to the measured resonant frequency shift. A calibration equation was obtained to predict moisture content from the measured frequency shift with an accuracy of 2%.

  3. Marketing techniques and cost calculations of radiation vulcanised natural rubber latex (RVNRL)

    International Nuclear Information System (INIS)

    Wan Manshol Wan Zin; Chai Chee Keong; Najib Mohammed Zakey; Hafizuddin Maseri

    2005-01-01

    This paper describes how RVNRL is promoted to the latex based industries locally and abroad. RVNRL promotion requires patience and very challenging. This is a fact since the product is new to the market. Cost is important in deciding its market and potential usage. The elements that contribute to the cost is described in this paper. (Author)

  4. Studies on physico-chemical and mechanical properties of the irradiated latex modified mortar

    International Nuclear Information System (INIS)

    Yassene, A.A.M.A.

    2009-01-01

    This thesis contains three chapter; chapter(I): Introduction and literature review on:- Introduction to polymer. - Mechanism of polymer-cement co-matrix formation.-Sulphate attack. - Solidification /stabilization of heavy metal in cement mortar. chapter(II): Materials and experimental techniques that include: 1- Preparation of latex polymer films from different polymer latices of styrene butadine rubber latex (SBR), poly (styrene-acrylic ester) latex (SAE) and vinylacetate /versatic -ester copolymer latex (C2A). The effect of γ-irradiation dose on the physico - chemical and mechanical properties of different latex polymer films was studied.2- Preparation of latex polymer-modified cement mortar with different ratios of cement: latex polymer and different curing method.3- Solidification /stabilization (S/S) of electroplating heavy metal precipitate in latex polymer- modified mortar with different cement /electroplating heavy metal sludge ratio. chapter(III) results and discussion

  5. Hierarchically structured self-supported latex films for flexible and semi-transparent electronics

    International Nuclear Information System (INIS)

    Määttänen, Anni; Ihalainen, Petri; Törngren, Björn; Rosqvist, Emil; Pesonen, Markus; Peltonen, Jouko

    2016-01-01

    Graphical abstract: - Highlights: • Transparent self-supported latex films were fabricated by a peel-off process. • Various template substrates were used for creating e.g. hierarchically structured latex films. • Ultra-thin and semi-transparent conductive gold electrodes were evaporated on the latex films.Electrochemical experiments were carried out to verify the applicability of the electrodes. - Abstract: Different length scale alterations in topography, surface texture, and symmetry are known to evoke diverse cell behavior, including adhesion, orientation, motility, cytoskeletal condensation, and modulation of intracellular signaling pathways. In this work, self-supported latex films with well-defined isotropic/anisotropic surface features and hierarchical morphologies were fabricated by a peel-off process from different template surfaces. In addition, the latex films were used as substrates for evaporated ultrathin gold films with nominal thicknesses of 10 and 20 nm. Optical properties and topography of the samples were characterized using UV–vis spectroscopy and Atomic Force Microscopy (AFM) measurements, respectively. The latex films showed high-level transmittance of visible light, enabling the fabrication of semi-transparent gold electrodes. Electrochemical impedance spectroscopy (EIS) measurements were carried out for a number of days to investigate the long-term stability of the electrodes. The effect of 1-octadecanethiol (ODT) and HS(CH_2)_1_1OH (MuOH) thiolation and protein (human serum albumin, HSA) adsorption on the impedance and capacitance was studied. In addition, cyclic voltammetry (CV) measurements were carried out to determine active medicinal components, i.e., caffeic acid with interesting biological activities and poorly water-soluble anti-inflammatory drug, piroxicam. The results show that the fabrication procedure presented in this study enables the formation of platforms with hierarchical morphologies for multimodal (optical and

  6. Hierarchically structured self-supported latex films for flexible and semi-transparent electronics

    Energy Technology Data Exchange (ETDEWEB)

    Määttänen, Anni, E-mail: anni.maattanen@abo.fi [Laboratory of Physical Chemistry, Faculty of Science and Engineering, Center for Functional Materials, Åbo Akademi University, Porthaninkatu 3, 20500, Turku (Finland); Ihalainen, Petri, E-mail: petri.ihalainen@abo.fi [Laboratory of Physical Chemistry, Faculty of Science and Engineering, Center for Functional Materials, Åbo Akademi University, Porthaninkatu 3, 20500, Turku (Finland); Törngren, Björn, E-mail: bjorn.torngren@abo.fi [Laboratory of Physical Chemistry, Faculty of Science and Engineering, Center for Functional Materials, Åbo Akademi University, Porthaninkatu 3, 20500, Turku (Finland); Rosqvist, Emil, E-mail: emil.rosqvist@abo.fi [Laboratory of Physical Chemistry, Faculty of Science and Engineering, Center for Functional Materials, Åbo Akademi University, Porthaninkatu 3, 20500, Turku (Finland); Pesonen, Markus, E-mail: markus.pesonen@abo.fi [Physics, Faculty of Science and Engineering, Center for Functional Materials, Åbo Akademi University, Porthaninkatu 3, 20500, Turku (Finland); Peltonen, Jouko, E-mail: jouko.peltonen@abo.fi [Laboratory of Physical Chemistry, Faculty of Science and Engineering, Center for Functional Materials, Åbo Akademi University, Porthaninkatu 3, 20500, Turku (Finland)

    2016-02-28

    Graphical abstract: - Highlights: • Transparent self-supported latex films were fabricated by a peel-off process. • Various template substrates were used for creating e.g. hierarchically structured latex films. • Ultra-thin and semi-transparent conductive gold electrodes were evaporated on the latex films.Electrochemical experiments were carried out to verify the applicability of the electrodes. - Abstract: Different length scale alterations in topography, surface texture, and symmetry are known to evoke diverse cell behavior, including adhesion, orientation, motility, cytoskeletal condensation, and modulation of intracellular signaling pathways. In this work, self-supported latex films with well-defined isotropic/anisotropic surface features and hierarchical morphologies were fabricated by a peel-off process from different template surfaces. In addition, the latex films were used as substrates for evaporated ultrathin gold films with nominal thicknesses of 10 and 20 nm. Optical properties and topography of the samples were characterized using UV–vis spectroscopy and Atomic Force Microscopy (AFM) measurements, respectively. The latex films showed high-level transmittance of visible light, enabling the fabrication of semi-transparent gold electrodes. Electrochemical impedance spectroscopy (EIS) measurements were carried out for a number of days to investigate the long-term stability of the electrodes. The effect of 1-octadecanethiol (ODT) and HS(CH{sub 2}){sub 11}OH (MuOH) thiolation and protein (human serum albumin, HSA) adsorption on the impedance and capacitance was studied. In addition, cyclic voltammetry (CV) measurements were carried out to determine active medicinal components, i.e., caffeic acid with interesting biological activities and poorly water-soluble anti-inflammatory drug, piroxicam. The results show that the fabrication procedure presented in this study enables the formation of platforms with hierarchical morphologies for multimodal

  7. Studied on Virgin Coconut Oil (VCO) and Olive Oil (OO) as an Alternative for Stabilizer of Radiation Vulcanized Natural Rubber Latex (RVNRL) Preparation

    International Nuclear Information System (INIS)

    Syuhada Ramli; Sofian Ibrahim; Mohd Noorwadi Mat Lazim

    2016-01-01

    This paper presents the effects of virgin coconut oil (VCO) and olive oil (OO) as an alternative stabilizer in the radiation vulcanized natural rubber latex (RVNRL). Potassium laurite (KL) as a stabilizer considered as a control of RVNRL sample were compared to mixed ratio 1:1 KL: VCO and 1:1 KL: OO stabilizer formulation. Total solid content (TSC) and tensile strength (TS) results showed no significant different between the formulations. Mechanical stability time (MST) indicates higher stability of RVNRL with addition of VCO. The fatty acid composition in VCO indicate VCO was acting well as stabilizer for latex stabilizer formulation. (author)

  8. Effect of magnetic and thermal properties of iron oxide nanoparticles (IONs) in nitrile butadiene rubber (NBR) latex

    International Nuclear Information System (INIS)

    Ong, Hun Tiar; Julkapli, Nurhidayatullaili Muhd; Hamid, Sharifah Bee Abd; Boondamnoen, O.; Tai, Mun Foong

    2015-01-01

    Nitrile butadiene rubber (NBR) gloves are one of the most important personal protective equipments but they are possible to tear off and contaminate food or pharmaceutical and healthcare products during manufacturing and packaging process. High tendency of torn glove remaining in food or products due to white or light flesh-coloured glove is not easy to be detected by naked eyes. In this paper, iron oxide nanoparticles (IONs) selected as additive for NBR to improve its detectability by mean of magnetic properties. IONs synthesized via precipitation method and compounded with NBR latex before casting on petri dish. The properties of IONs were investigated by X-ray Diffractometry (XRD), Transmission Electron Microscope (TEM), Raman Spectroscopy and Vibrating Sample Magnetometer (VSM). Meanwhile NBR/IONs composites were studied by Thermogravimetry Analysis (TGA), Differential Scanning Calorimetry (DSC) and Vibrating Sample Magnetometer (VSM). It observed that, synthesized IONs shows of 25.28 nm crystallite with 25.86 nm semipherical (changed as) shape. Meanwhile, Magnetite and maghemite phase are found in range of 670 cm −1 and 700 cm −1 respectively, which it contributes magnetization saturation of 73.96 emu/g at 10,000 G by VSM. Thermal stability and magnetic properties were increased with incorporating IONs into NBR latex up to 20 phr. NBR/IONs 5 phr has the optimum thermal stability, lowest glass transition temperature (−14.83 °C) and acceptable range of magnetization saturation (3.83 emu/g at 10,000 G) to form NBR gloves with magnetic detectability. - Highlights: • We synthesized IONs with high magnetization saturation (M s ). • High M s of IONs were incorporated into NBR latex in order to induce magnetic properties in the NBR composite. • Introduction of IONs into NBR latex would improve thermal properties. • The produced NBR/IONs 5 phr composite exceeded the minimum magnetic moment sensor of the detector. • They have high potential for the

  9. Effect of magnetic and thermal properties of iron oxide nanoparticles (IONs) in nitrile butadiene rubber (NBR) latex

    Energy Technology Data Exchange (ETDEWEB)

    Ong, Hun Tiar; Julkapli, Nurhidayatullaili Muhd; Hamid, Sharifah Bee Abd, E-mail: sharifahbee@um.edu.my; Boondamnoen, O.; Tai, Mun Foong

    2015-12-01

    Nitrile butadiene rubber (NBR) gloves are one of the most important personal protective equipments but they are possible to tear off and contaminate food or pharmaceutical and healthcare products during manufacturing and packaging process. High tendency of torn glove remaining in food or products due to white or light flesh-coloured glove is not easy to be detected by naked eyes. In this paper, iron oxide nanoparticles (IONs) selected as additive for NBR to improve its detectability by mean of magnetic properties. IONs synthesized via precipitation method and compounded with NBR latex before casting on petri dish. The properties of IONs were investigated by X-ray Diffractometry (XRD), Transmission Electron Microscope (TEM), Raman Spectroscopy and Vibrating Sample Magnetometer (VSM). Meanwhile NBR/IONs composites were studied by Thermogravimetry Analysis (TGA), Differential Scanning Calorimetry (DSC) and Vibrating Sample Magnetometer (VSM). It observed that, synthesized IONs shows of 25.28 nm crystallite with 25.86 nm semipherical (changed as) shape. Meanwhile, Magnetite and maghemite phase are found in range of 670 cm{sup −1} and 700 cm{sup −1} respectively, which it contributes magnetization saturation of 73.96 emu/g at 10,000 G by VSM. Thermal stability and magnetic properties were increased with incorporating IONs into NBR latex up to 20 phr. NBR/IONs 5 phr has the optimum thermal stability, lowest glass transition temperature (−14.83 °C) and acceptable range of magnetization saturation (3.83 emu/g at 10,000 G) to form NBR gloves with magnetic detectability. - Highlights: • We synthesized IONs with high magnetization saturation (M{sub s}). • High M{sub s} of IONs were incorporated into NBR latex in order to induce magnetic properties in the NBR composite. • Introduction of IONs into NBR latex would improve thermal properties. • The produced NBR/IONs 5 phr composite exceeded the minimum magnetic moment sensor of the detector. • They have high

  10. The rapid determination of volatile fatty acid number in para rubber latex using fourier transform-near infrared spectroscopy based on quantification and discrimination model

    Directory of Open Access Journals (Sweden)

    Sureeporn Narongwongwattana

    2015-09-01

    Full Text Available Volatile Fatty Acid number (VFA no. is one of the parameters indicating the state of quality of Para rubber latex at that particular time. Most factories analyze this parameter using standard analytical method as in ISO 506:1992(E. Nevertheless, this procedure is complicated, chemical and time consuming, as well as skilled analyst required. Therefore, near infrared (NIR spectroscopy which is rapid, accurate and nonchemicals method was applied to determine the VFA no. in field latex and concentrated latex based on quantification and discriminant model. The best calibration equation was obtained from standard normal variate (SNV spectra in the region of 6109.7–5770.3, 4613.1–4242.9 cm-1 with R = 0.832, SECV = 0.036 and no bias. From the performance check, statistically it was found that SECV and bias were low enough for practical acceptance and the predicted VFA no. was not different significantly from actual VFA no. at 95% confidence intervals. In addition, discriminant model was developed to separate good quality latex from the deteriorated latex using VFA no. at 0.06 as standard as in ISO 2004:2010(E. The discriminant model can be used to screen the latex with overall accuracy of 91.86% in validation set.

  11. Ten years incidence of natural rubber latex sensitization and symptoms in a prospective cohort of health care workers using non-powdered latex gloves 2000-2009.

    Science.gov (United States)

    Larese Filon, Francesca; Bochdanovits, Letizia; Capuzzo, Chiara; Cerchi, Roberto; Rui, Francesca

    2014-07-01

    To assess the incidence of sensitization and gloves-related symptoms in 10-year follow-up in a group of health care workers (9,660 person-years) using non-powdered latex gloves from 2000 to 2009 and to examine related factors. We studied 2,053 health care workers in Trieste Hospitals by means of skin prick test for latex extract, patch tests and medical examinations. We report the incidence of latex sensitization among workers using non-powdered latex gloves. The incidence of latex sensitization, rhinitis, asthma, urticaria, irritant and allergic contact dermatitis were 1.0; 0.12; 0.21; 0.72; 2.39 and 2.50 cases per 1,000 person-years, respectively. Respiratory symptoms and urticaria were positively related with latex sensitization (OR = 8.0; 95 % CL 1.27-48.6), with common allergic respiratory symptoms (OR = 4.19; 95 % CL 1.04-16.8) and with familial atopy (OR = 4.47; 95 % CL 1.1-17.9). The incidence of latex sensitization and latex-related symptoms were very low but subjects with allergic symptoms related to common allergens are at higher risk. The use of non-latex gloves is suggested for them.

  12. Caracterização da hipersensibilidade a luvas de látex em profissionais da odontologia = Rubber latex gloves hypersensitivities in dental workers

    Directory of Open Access Journals (Sweden)

    Flávia Sukekava

    2007-01-01

    Full Text Available As reações alérgicas ao látex vêm aumentando em profissionais da saúde e se manifestam como um incômodo local ou sintomatologia sistêmica. Para conhecer a freqüência das manifestações alérgicas nos usuários de luvas de látex foi realizada busca entre os profissionais da odontologia via aplicação de questionários. Foram aplicados 450questionários e, dentre os respondedores (140, 19% relataram manifestar reações locais ao contato com as luvas de látex e 5% reações sistêmicas a outros produtos de látex. Cerca de 2,5% declararam dermatite de contato e reações sistêmicas (anafiláticas, 1,5% apenas dermatite de contato e 1% sintomas de anafilaxia ao uso das luvas. Vinte por cento dos profissionais atenderam pacientes com alergia ao látex e 29% declararam questionar, durante a anamnese, a respeito de alergia ao látex. As reações alérgicas a luvas de látex foram freqüentes e é objeto de preocupação entre os profissionais da odontologia.Allergic reactions to natural rubber latex have increased in dental practice affecting both the professional and the patients. Allergic reactions may range from skin disease to asthma and anaphylaxis. This study aimed at determining the incidence of latex gloves allergy amongdental care workers. 450 allergy questionnaires were used to collect information on latex gloves reactions and 140 dental works answered them. Latex gloves reaction occurred in 19% of them and 5% reported allergic reactions to other latex products. 2.5% reported symptoms suggesting contact dermatitis and anaphylaxis hypersensitivities, 1.5% contact dermatitis, and 1% reported anaphylaxis symptoms when wearing them. 20% of them had patients who presented symptoms suggestive of anaphylaxis hypersensitivity to rubber gloves latex. Our study confirms that rubber latex gloves reactions are frequent among dental care workers, and dentists must be aware of the latex allergy in dental practice.

  13. Formation of Defect-Free Latex Films on Porous Fiber Supports

    KAUST Repository

    Lively, Ryan P.

    2011-09-28

    We present here the creation of a defect-free polyvinylidene chloride barrier layer on the lumen-side of a hollow fiber sorbent. Hollow fiber sorbents have previously been shown to be promising materials for enabling low-cost CO 2 capture, provided a defect-free lumen-side barrier layer can be created. Film experiments examined the effect of drying rate, latex age, substrate porosity (porous vs nonporous), and substrate hydrophobicity/ hydrophilicity. Film studies show that in ideal conditions (i.e., slow drying, fresh latex, and smooth nonporous substrate), a defect-free film can be formed, whereas the other permutations of the variables investigated led to defective films. These results were extended to hollow fiber sorbents, and despite using fresh latex and relatively slow drying conditions, a defective lumen-side layer resulted. XRD and DSC indicate that polyvinylidene chloride latex develops crystallinity over time, thereby inhibiting proper film formation as confirmed by SEM and gas permeation. This and other key additional challenges associated with the porous hollow fiber substrate vs the nonporous flat substrate were overcome. By employing a toluene-vapor saturated drying gas (a swelling solvent for polyvinylidene chloride) a defect-free lumen-side barrier layer was created, as investigated by gas and water vapor permeation. © 2011 American Chemical Society.

  14. Preparation of novel film-forming armoured latexes using silica nanoparticles as a pickering emulsion stabiliser.

    Science.gov (United States)

    Shiraz, Hana; Peake, Simon J; Davey, Tim; Cameron, Neil R; Tabor, Rico F

    2018-05-15

    Film-forming polymer latex particles of diameter acrylate (BA) as co-monomers, potassium persulphate (KPS) as an initiator and a commercially available colloidal nano-silica (Ludox®-TM40). It was found that pH control before polymerisation using methacrylic acid (MAA) facilitated the formation of armoured latexes, and mechanistic features of this process are discussed. An alternative, more robust protocol was developed whereby addition of vinyltriethoxysilane (VTES) to control wettability resulted in latexes completely armoured in colloidal nano-silica. The latexes were characterised using SEM, cryo-TEM and AFM imaging techniques. The mechanism behind the adsorption was investigated through surface pressure and contact angle measurements to understand the factors that influence this irreversible adsorption. Results indicate that nanoparticle attachment (but intriguingly not latex size) is dependent on particle wettability, providing new insight into the formation of nanoparticle-armoured latexes, along with opportunities for further development of diversely functionalized inorganic/organic polymer composite particles. Copyright © 2018 Elsevier Inc. All rights reserved.

  15. Effect of magnetic and thermal properties of iron oxide nanoparticles (IONs) in nitrile butadiene rubber (NBR) latex

    Science.gov (United States)

    Ong, Hun Tiar; Julkapli, Nurhidayatullaili Muhd; Hamid, Sharifah Bee Abd; Boondamnoen, O.; Tai, Mun Foong

    2015-12-01

    Nitrile butadiene rubber (NBR) gloves are one of the most important personal protective equipments but they are possible to tear off and contaminate food or pharmaceutical and healthcare products during manufacturing and packaging process. High tendency of torn glove remaining in food or products due to white or light flesh-coloured glove is not easy to be detected by naked eyes. In this paper, iron oxide nanoparticles (IONs) selected as additive for NBR to improve its detectability by mean of magnetic properties. IONs synthesized via precipitation method and compounded with NBR latex before casting on petri dish. The properties of IONs were investigated by X-ray Diffractometry (XRD), Transmission Electron Microscope (TEM), Raman Spectroscopy and Vibrating Sample Magnetometer (VSM). Meanwhile NBR/IONs composites were studied by Thermogravimetry Analysis (TGA), Differential Scanning Calorimetry (DSC) and Vibrating Sample Magnetometer (VSM). It observed that, synthesized IONs shows of 25.28 nm crystallite with 25.86 nm semipherical (changed as) shape. Meanwhile, Magnetite and maghemite phase are found in range of 670 cm-1 and 700 cm-1 respectively, which it contributes magnetization saturation of 73.96 emu/g at 10,000 G by VSM. Thermal stability and magnetic properties were increased with incorporating IONs into NBR latex up to 20 phr. NBR/IONs 5 phr has the optimum thermal stability, lowest glass transition temperature (-14.83 °C) and acceptable range of magnetization saturation (3.83 emu/g at 10,000 G) to form NBR gloves with magnetic detectability.

  16. Radio-vulcanization of natural rubber in the latex phase. Study of an experimental 1 tonne per hour production; Radio-vulcanisation du caoutchouc naturel en phase latex. Etude d'une production experimentale de 1 tonne par heure

    Energy Technology Data Exchange (ETDEWEB)

    Leveque, P; Puig, J R; Roudeix, H [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1968-07-01

    After briefly reviewing the main research carried out on the radio-vulcanization of latex and elastomers, a description is given of 4 types of cell which have been used successively with a view to industrial irradiation. They have made it possible to acquire the information necessary for resolving the main problem arising during irradiation - the formation of coagulum. The first two cell are designed for irradiation by a horizontal beam ('Dynamitron'), the two others use a vertical beam ('Circe'). The study of the properties of the rubber obtained shows it to compare favorably with 'Revultex'. In the appendix are given some characteristics of natural latex and information about its processing. (authors) [French] Apres un rappel des principales etudes sur la radio-vulcanisation du latex et des elastomeres, on decrit les quatre types de cellules successivement essayes en vue de l'irradiation industrielle. Ils ont permis d'acquerir les informations necessaires a la resolution du probleme principal pose par l'irradiation, la formation de coagulum au cours de celle,-ci. Les deux premiers sont concus pour l'irradiation par un faisceau horizontal ('Dynamitron'), les derniers par un faisceau vertical ('Circe'). L'etude des proprietes du caoutchouc obtenu montre qu'il se compare favorablement au 'Revultex'. Un apercu est donne en annexe des caracteristiques du latex naturel et de sa mise en oeuvre. (auteurs)

  17. Transdermal nicotine mixed natural rubber-hydroxypropylmethylcellulose film forming systems for smoking cessation: in vitro evaluations.

    Science.gov (United States)

    Pichayakorn, Wiwat; Suksaeree, Jirapornchai; Boonme, Prapaporn; Taweepreda, Wirach; Amnuaikit, Thanaporn; Ritthidej, Garnpimol C

    2014-08-27

    Abstract Novel film forming polymeric dispersions for transdermal nicotine delivery were prepared from deproteinized natural rubber latex (DNRL) blended with hydroxypropylmethylcellulose (HPMC) and dibutyl phthalate (DBP) or glycerin (GLY) as plasticizer. The preliminary molecular compatibility of ingredients was observed by Fourier transform infrared spectroscopy, differential scanning calorimetry and X-ray diffractometry characterizations. All film forming polymeric dispersions were elegant in appearance and smooth in texture without agglomeration. Their pH was 7-8. In addition, their viscosity and spreadability showed good characteristics depended on HPMC and plasticizers blended. The transparent in situ dry films with good strength and elasticity were also confirmed by peeling-off. The nicotine release from them revealed an initial fast release that was similar to the release from a concentrated nicotine solution, and followed by slow release pattern from the in situ films. GLY blended formulation produced a higher amount of nicotine permeation through the in vitro pig skin than DBP blends. Ethanol mixing also enhanced nicotine permeation, but it affected the integrity of in situ films. The nicotine release and skin permeation kinetics were by a diffusion mechanism that was confirmed by the Higuchi's model. These formulations were safe without producing any severe skin irritation. However, for the stability they needed to be stored at 4 °C in tightly sealed containers.

  18. Deproteinised natural rubber latex grafted poly(dimethylaminoethyl methacrylate) - poly(vinyl alcohol) blend membranes: Synthesis, properties and application.

    Science.gov (United States)

    Jayadevan, Janisha; Alex, Rosamma; Gopalakrishnapanicker, Unnikrishnan

    2018-02-01

    Natural rubber latex was initially deproteinised (DNRL) and then subjected to physicochemical modifications to make high functional membranes for drug delivery applications. Initially, DNRL was prepared by incubating with urea, sodiumdodecylsulphate and acetone followed by centrifugation. The deproteinisation was confirmed by CHN analysis. The DNRL was then chemically modified by grafting (dimethylaminoethyl methacrylate) onto NR particles by using a redox initiator system viz; cumene hydroperoxide/tetraethylenepentamine, followed by dialysis for purification. The grafting was confirmed by dynamic light scattering, Fourier transform infrared spectroscopy and nuclear magnetic resonance spectroscopy. The grafted system was blended with a hydrophilic adhesive polymer PVA and casted into membranes. The membranes after blending showed enhanced mechanical properties with a threshold concentration of PVA. The moisture uptake, swelling and water contact angle experiments indicated an increased hydrophilicity with an increased PVA content in the blend membranes. The grafted DNRL possessed significant antibacterial property which has been found to be retained in the blended form. A notable decrease in cytotoxicity was observed for the modified DNRL membranes than the bare DNRL membranes. The in-vitro drug release studies using rhodamine B as a model drug, confirmed the utility of the prepared membranes to function as a drug delivery matrix. Copyright © 2017 Elsevier B.V. All rights reserved.

  19. Novel Polyvinyl Alcohol/Styrene Butadiene Rubber Latex/Carboxymethyl Cellulose Nanocomposites Reinforced with Modified Halloysite Nanotubes

    Directory of Open Access Journals (Sweden)

    Yanjun Tang

    2013-01-01

    Full Text Available Novel polyvinyl alcohol (PVA/styrene butadiene rubber (SBR latex/carboxymethyl cellulose (CMC/halloysite nanotubes (HNTs nanocomposites were successfully prepared through physical blending. The as-obtained PVA/SBR/CMC/HNTs nanocomposites were coated on the surface of old corrugated container (OCC-based paper in an effort to improve the mechanical properties of paper. To improve the dispersion of HNTs and enhance the compatibility between HNTs and polymer matrix, HNTs were modified with titanate coupling agent (TCA. FT-IR, together with TGA, confirmed that TCA was grafted onto the surface of HNTs successfully. XRD demonstrated that the crystal structures of HNTs remained almost unchanged. TEM showed that modified HNTs exhibited good dispersion and possessed nanotubular structures with an outer diameter of around 50 nm and an inner diameter of about 20 nm. SEM gave an indication that modified HNTs were dispersed more uniformly than unmodified HNTs within PVA/SBR/CMC matrix. Rheological measurement exhibited that surface modification process enhanced the compatibility between HNTs and polymer matrix, thus resulting in the decreased viscosity of nanocomposites. In comparison with unmodified HNTs, modified HNTs were found to contribute more to the enhancement in mechanical properties, which might be attributed to the better dispersion and compatibility of modified HNTs evidenced by TEM, SEM, and rheological measurement.

  20. Composite Films Formed by Cellulose nanocrystals and Latex Nanoparticles: Optical, Structural, and Mechanical Properties

    Science.gov (United States)

    Vollick, Brandon McRae

    This thesis describes the preparation of iridescent, birefringent, composite films composed of cellulose nanocrystals (CNCs), latex nanoparticles (NPs) and a NP crosslinker; hexanediamine (HDA). First, aqueous suspensions were prepared with varying quantities of CNCs, NPs and HDA before equilibrating for one week. The cholesteric (Ch) phase was then cast and dried into a film. The optical, structural and mechanical properties of the film was analyzed. Second, films with identical compositions of CNCs, NPs, and HDA were fabricated in three different ways to yield films of different morphology, (i) fast drying of an isotropic suspension, yielding an isotropic film, (ii) slow drying of an isotropic suspension, yielding a partially Ch films, (iii) slow drying of an equilibrated suspension, yielding a highly Ch film. The optical and mechanical properties of the films was analyzed.

  1. Comparative evaluation of Type 1 latex hypersensitivity in patients with chronic urticaria, rubber factory workers and healthy control subjects

    NARCIS (Netherlands)

    Piskin, Gamze; Akyol, Aynur; Uzar, Hatice; Tulek, Necla; Boyvat, Ayse; Gurgey, Erbak

    2003-01-01

    Latex hypersensitivity manifests itself most commonly with contact urticaria. In this study, we investigated the frequency of latex hypersensitivity as a possible aetiological factor in patients with chronic urticaria (CU) and compared latex hypersensitivity of CU patients (n = 50) with that of

  2. Hierarchically structured self-supported latex films for flexible and semi-transparent electronics

    Science.gov (United States)

    Määttänen, Anni; Ihalainen, Petri; Törngren, Björn; Rosqvist, Emil; Pesonen, Markus; Peltonen, Jouko

    2016-02-01

    Different length scale alterations in topography, surface texture, and symmetry are known to evoke diverse cell behavior, including adhesion, orientation, motility, cytoskeletal condensation, and modulation of intracellular signaling pathways. In this work, self-supported latex films with well-defined isotropic/anisotropic surface features and hierarchical morphologies were fabricated by a peel-off process from different template surfaces. In addition, the latex films were used as substrates for evaporated ultrathin gold films with nominal thicknesses of 10 and 20 nm. Optical properties and topography of the samples were characterized using UV-vis spectroscopy and Atomic Force Microscopy (AFM) measurements, respectively. The latex films showed high-level transmittance of visible light, enabling the fabrication of semi-transparent gold electrodes. Electrochemical impedance spectroscopy (EIS) measurements were carried out for a number of days to investigate the long-term stability of the electrodes. The effect of 1-octadecanethiol (ODT) and HS(CH2)11OH (MuOH) thiolation and protein (human serum albumin, HSA) adsorption on the impedance and capacitance was studied. In addition, cyclic voltammetry (CV) measurements were carried out to determine active medicinal components, i.e., caffeic acid with interesting biological activities and poorly water-soluble anti-inflammatory drug, piroxicam. The results show that the fabrication procedure presented in this study enables the formation of platforms with hierarchical morphologies for multimodal (optical and electrical) real-time monitoring of length-scale-dependent biomaterial-surface interactions.

  3. Preliminary study of semi-refined carrageenan (SRC) as secondary gelling agent in natural rubber (NR) latex foam

    Science.gov (United States)

    Norhazariah, S.; Azura, A. R.; Azahari, B.; Sivakumar, R.

    2017-12-01

    Semi-refined carrageenan (SRC) product is considerably cheaper and easier to produce as a natural polysaccharide, which was utilized in food and other product application. However, the application in latex is limited. The aim of this work is to evaluate the SRC produced from low industrial grade seaweed (LIGS) in the latex foam application. The FTIR spectra showed the SRC produced as kappa type carrageenan with lower sulfur content compared to native LIGS. NR latex foam is produced by using the Dunlop method with some modifications. The effect of SRC loading as a secondary gelling agent in NR latex foam is investigated. The density and morphology of the NR latex foam with the addition of the SRC are analyzed. NR latex foam density increased with SRC loading and peaked at 1.8 phr SRC. The addition of SRC has induced the bigger cell size compared to the cell size of the control NR latex foam, as shown in the optical micrograph. It can be concluded that SRC LIGS could be acted as secondary gelling agent in NR latex foam.

  4. Tensile properties of latex paint films with TiO2 pigment

    Science.gov (United States)

    Hagan, Eric W. S.; Charalambides, Maria N.; Young, Christina T.; Learner, Thomas J. S.; Hackney, Stephen

    2009-05-01

    The tensile properties of latex paint films containing TiO2 pigment were studied with respect to temperature, strain-rate and moisture content. The purpose of performing these experiments was to assist museums in defining safe conditions for modern paintings held in collections. The glass transition temperature of latex paint binders is in close proximity to ambient temperature, resulting in high strain-rate dependence in typical exposure environments. Time dependence of modulus and failure strain is discussed in the context of time-temperature superposition, which was used to extend the experimental time scale. Nonlinear viscoelastic material models are also presented, which incorporate a Prony series with the Ogden or Neo-Hookean hyperelastic function for different TiO2 concentrations.

  5. Effect of Amphiphilic Alkyl Chain Length Upon Purified LATEX Stability

    International Nuclear Information System (INIS)

    Amira Amir Hassan; Amir Hashim Mohd Yatim

    2015-01-01

    Rubber particles in purified latex (PL) are stabilized by a film of protein and fatty acid soap (surfactant). Saturated straight-chain fatty acid soaps can assist an enhancement of latex stability. However, whether the alkyl chain length plays an important role in increasing the stability is still an issue. The aim of this study is to investigate the effect of alkyl chain length of anionic surfactant on the stability of purified latex. The fatty acid soap of decanoate (9), laurate (11), sodium dodecyl sulphate (SDS) (12) and palmitate (15) were used. The numbers in parentheses indicating the number of carbon present in alkyl chain of the soap. The results showed that the impact of alkyl chain length on the stability of latex is in the order of laurate > decanoate > SDS > palmitate > purified latex accordingly. The alkyl chain length does giving a significant effect on latex stability after longer stirring time. The particle size of latex with the presence of surfactant is greater compare to a single particle itself due to extension of particles diameter. Thus suitable interaction of the nonpolar tail of surfactant with the hydrophobic regions of latex surface played a major role in maintaining a stable latex system. (author)

  6. Study on the production of kanvas shoes adhesive from natural rubber latex grafted with methyl methacrylate (NRL-g PMMA) copolymer

    International Nuclear Information System (INIS)

    Utama, Marga; Sudirman; Setyowati, Penny

    2002-01-01

    The optimation condition of radiation copolymerization of MMA into natural rubber latex at the doses of radiation : 5; 7.5 and 10 kGy with concentration of MMA 25; 50; 75; and 100 phr (Part Hundred Ratio of Rubber) expectially and optimazation condition of the adhesive process all the production of canvas shoes have been carried out. The properties of NRL-g-MMA and its rubber such as total solid contain, viscosity, pH, modulus, tensile, strenght, hardnes, elongation at break, and adhesive strenght for producting canvas shoes where evaluated. The at adhesive results show that NRL-g-MMA with the 75 phr of MMA and iradiation dose 5 kGy is adhesive will good stability during storage. The adhesive strenght of shoes its 16-18 N/6mm, more here than SNI 1-0172-1987 with the value 10N/6mm. Besic there is a tendency that adhesive strengt of product shoes at rome temperature (30-50 o C). stronger than at high temperature (100 o C)

  7. Epoxidação "in situ" aplicada ao látex de borracha natural "In situ" epoxidation of natural rubber latex

    Directory of Open Access Journals (Sweden)

    Cristiane K. Santin

    2012-01-01

    Full Text Available O comportamento da borracha natural na forma látex frente à reação de epoxidação foi avaliado visando estabelecer as melhores condições reacionais sem a ocorrência de reações laterais, que promovem a coagulação do látex e o desenvolvimento de um aglomerado de borracha. Grupos epóxidos foram gerados através da reação de epoxidação a partir da formação in situ do ácido perfórmico. As amostras foram caracterizadas qualitativamente por espectroscopia de infravermelho (FTIR e o grau de modificação determinado por ressonância magnética nuclear de hidrogênio (1H-RMN. Análises de calorimetria exploratória diferencial (DSC demonstraram que a mobilidade da cadeia polimérica foi influenciada pela presença de grupos epóxidos, com aumento linear na temperatura de transição vítrea (Tg. Os resultados indicaram que a epoxidação do látex de borracha natural, sem a ocorrência de reações laterais, é possível e dependente das condições reacionais.Natural rubber latex was submitted to epoxidation reaction to establish the best reaction conditions without the occurrence of side reactions, which promote coagulation of the latex and development of an agglomerate of rubber. Epoxy groups were produced by in situ epoxidation with formic acid and hydrogen peroxide. The samples were characterized qualitatively by Fourier Transform Infrared (FTIR analysis and the degree of modification determined by Hydrogen Nuclear Magnetic Resonance Spectroscopy (1H-NMR analysis. A linear increase in the glass transition temperature (Tg was observed. The results show that the epoxidation of natural rubber latex is possible and depends on the reaction conditions.

  8. EFFECT OF THE PHASE STRUCTURE EVOLUTION ON THE PROPERTIES OF FILMS FORMED FROM PBA/P(ST-CO-MMA)COMPOSITE LATEX

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    A group of heterogeneous latexes poly(butyl acrylate)/poly(styrene-co-methyl methacrylate)(PBA/P(St-co-MMA))were prepared by a semi-continuous seeded emulsion polymerization process under monomer starved conditions.The glass transition temperature(Tg)and the mechanical properties of the film formed from the composite latex changed with the evolution of the particle morphology.A photon transmission method was used to monitor the phase structure evolution of films which were prepared from core-shell PBA/P(St-co-MMA)latex at room temperature and annealed at 383 K above Tg of the polymers.In addition,the changes of the surface of the film formed from the composite latex with time at 383 K were observed by AFM.The evidence illustrated that the film formed from the core-shell latex particles was metastable.The rearrangement of the phases could occur under proper conditions.

  9. Improvement of RVNRL film properties by adding fumed silica and hydroxy apatite

    Directory of Open Access Journals (Sweden)

    Adul Thiangchanya

    2003-01-01

    Full Text Available The effect of adding fumed silica and hydroxy apatite to Radiation Vulcanized Natural Rubber Latex (RVNRL for improving tear strength, aging properties, degradability and water-soluble protein content of rubber films has been investigated. The addition of fumed silica and hydroxy apatite in RVNRL improves tear strength and aging properties of rubber films, whereas tensile strength and degradability of rubber films were unchanged during storage at room temperature. The water-soluble protein content in rubber films was reduced by immobilization of the fumed silica and hydroxy apatite and enhanced by addition of ZnO. This may reduce allergy problems of natural rubber latex products caused by water-soluble protein. The MST of the RVNRL with fumed silica and hydroxy apatite indicated that the latex must be used within two months after mixing because of its stability.

  10. Morphology and film formation of poly(butyl methacrylate)-polypyrrole core-shell latex particles

    NARCIS (Netherlands)

    Huijs, F; Lang, J

    Core-shell latex particles made of a poly(butyl methacrylate) (PBMA) core and a thin polypyrrole (PPy) shell were synthesized by two-stage polymerization. In the first stage, PBMA latex particles were synthesized in a semicontinuous process by free-radical polymerization. PBMA latex particles were

  11. Evaluation of wound healing treated with latex derived from rubber trees and Aloe Vera extract in rats.

    Science.gov (United States)

    Brandão, Marcelo Luiz; Reis, Paulo Roberto Melo; Araújo, Lilhian Alves de; Araújo, Ana Carolina Vicente; Santos, Maisa Helena de Abreu Silva; Miguel, Marina Pacheco

    2016-09-01

    To compare the use of latex derivative and Aloe vera extract to wound healing. Twenty one rats were randomly divided into three groups and each one had a wound made by incision. The treatment consisted in: derivative of latex (GL), Aloe vera extract (GA) and saline solution (GC). The wound area was measured on the 7th, 14th and 21st days and macroscopic and microscopic evaluation were done. The comparison between the measurements of the wounds presented statistical difference in GC and GA from the 7th day of evaluation and GL from the 14th day. The extent of the wound was significantly smaller by the 7th day in GL. Histologically, in GL, the neovascularization was significant on the 7th, 14th and 21st days. On the 21st day the scar was large and little mature. In GA and GC, the findings were similar on the 7th, 14th and 21st days with a slight better organization of skin and collagen on the 21st in GA. Statistical analysis did not allow for the definition of the best topical agent. The latex had the highest angiogenesis, but a possible foreign body granuloma. Aloe vera has revealed a healing process adequated temporally in histology.

  12. Latex allergy in health care

    Directory of Open Access Journals (Sweden)

    Tina Virtič

    2012-11-01

    Full Text Available The increasing use of natural rubber latex medical gloves in the last three decades has caused an increase in latex allergy. The majority of risk groups for allergy development include health care workers, workers in the rubber industry, atopic individuals and children with congenital malformations. Three types of pathological reactions can occur in people using latex medical gloves: irritant contact dermatitis, allergic contact dermatitis and immediate hypersensitivity. The latex allergy is caused by constituent components of latex gloves and added powders; there are also numerous latex allergens involved in cross-reactivity between latex and fruits and vegetables, the so-called latex-fruit syndrome. The diagnosis is based on an accurate history of exposure, clinical presentation and confirmatory in vivo and in vitro tests. Prevention is the easiest, most effective and least expensive way to avoid latex allergy. Powder-free latex gloves with reduced levels of proteins and chemicals, and synthetic gloves for allergic workers must be provided in the work environment. There are already many health care institutions around the world where all latex products have been replaced by synthetic material products.

  13. Modification of rubber surface with hydrogenated diamond-like carbon thin films

    NARCIS (Netherlands)

    Pei, Y. T.; Bui, X. L.; De Hosson, J. Th. M.; Laudon, M; Romanowicz, B

    2009-01-01

    Thin films of hydrogenated diamond-like carbon (DLC) have been deposited on hydrogenated nitrile butadiene rubber (HNBR) for reduction of friction and enhancement of wear resistance of dynamic rubber seals, by sputtering graphite targets in C(2)H(2)/Ar plasma. The wax removal and pre-deposition

  14. Flexible diamond-like carbon thin film coated on rubbers: fundamentals and applications

    NARCIS (Netherlands)

    Pei, Yutao

    2015-01-01

    Dynamic rubber seals are the major source of friction in lubrication systems and bearings, which may take up to 70% of the total friction. Our solution is to coat rubbers with flexible diamond-like carbon (DLC) thin film by which the coefficient of friction is reduced from above 1.5 to below 0.15.

  15. Flexible diamond-like carbon thin film coated rubbers: fundamentals and applications

    NARCIS (Netherlands)

    Pei, Y.T.

    2015-01-01

    Dynamic rubber seals are major sources of friction of lubrication systems and bearings, which may take up to 75% of the total friction. The solution we present is to coat rubbers with diamond-like carbon (DLC) thin film, by which the coefficient of friction is reduced to less than one tenth. Coating

  16. Rubber

    Science.gov (United States)

    Graves, D. F.

    The word "rubber" immediately brings to mind materials that are highly flexible and will snap back to their original shape after being stretched. In this chapter a variety of materials are discussed that possess this odd characteristics. There will also be a discussion on the mechanism of this "elastic retractive force." Originally, rubber meant the gum collected from a tree growing in Brazil. The term "rubber" was coined for this material by the English chemist Joseph Priestley, who noted that it was effective for removing pencil marks from paper. Today, in addition to Priestley's natural product, many synthetic materials are made that possess these characteristics and many other properties. The common features of these materials are that they are made up of long-chain molecules that are amorphous (not crystalline), and the chains are above their glass transition temperature at room temperature.

  17. Use of low energy accelerator for the radiation vulcanization of natural rubber latex and nitrile rubber. The battle for the sustainability and poverty alleviation

    International Nuclear Information System (INIS)

    Chirinos, Hugo D.; Lugao, Ademar B.

    2001-01-01

    The origin of the Hevea braziliensis tree was the Amazonian basin. The rubber expansion at the end of 19th century brought prosperity and determined the borders of Amazonian countries. In spite of that, the Brazilian government has failed in establishing a successful policy for improving the NR production in the jungle. This battle has been a continuous defeat against the environment as it was not possible to control the fungus Microcyclos ulei in its natural environment. The defeat was catastrophic for the population of Amazon region as they were not able to shift to other sustainable activity. As a consequence of the tack of economical options, the population had to explore all available natural resources. It has been also catastrophic for the Amazonian environment. Nevertheless, rubber plantations were successfully introduced in areas were Hevea braziliensis was not native, mainly in the southeast of Brazil. And recently, it was also introduced near marginal areas of the humid forest in the Amazon due to the absence of the fungus Microcyclos ulei. Both, extraction of wild rubber and plantation have a key role in the maintenance of the forest health as the seringueiros not only have a sustainable activity but can also play a role as soldiers of the jungle. Actually, rubber activities are not only associated to the environment but also with poverty because the activities are labor intensive, so it needs cheap labor. The poverty is unfortunately spread out in rural areas of Brazil and in the peripheral areas of the big cities. Regarding environment and poverty the dilemma is critical in the Amazonian region and is the following: the forest should be maintained healthy and protected from devastating projects and at the same time needs of the inhabitants should be considered. (author)

  18. Multifunctional, Nanostructured Metal Rubber Protective Films for Space Exploration, Phase II

    Data.gov (United States)

    National Aeronautics and Space Administration — NanoSonic has developed revolutionary nanostructured, yet macroscale, multifunctional Metal RubberTM films. In support of NASA's Vision for Space Exploration, low...

  19. Multifunctional, Nanostructured Metal Rubber Protective Films for Space Exploration, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — NanoSonic has developed revolutionary nanostructured, yet macroscale, multifunctional Metal RubberTM films. In support of NASA's Vision for Space Exploration, low...

  20. Microstructure and chemical bonding of DLC films deposited on ACM rubber by PACVD

    NARCIS (Netherlands)

    Martinez-Martinez, D.; Schenkel, M.; Pei, Y.T.; Sánchez-López, J.C.; Hosson, J.Th.M. De

    2011-01-01

    The microstructure and chemical bonding of DLC films prepared by plasma assisted chemical vapor deposition on acrylic rubber (ACM) are studied in this paper. The temperature variation produced by the ion impingement during plasma cleaning and subsequent film deposition was used to modify the film

  1. Transcript Profiling of Hevea brasiliensis during Latex Flow

    Directory of Open Access Journals (Sweden)

    Jinquan Chao

    2017-11-01

    Full Text Available Latex exploitation enhances latex regeneration in rubber trees. The latex exploitation-caused latex flow lasts from 10 min to a few hours, which is convenient for exploring the transcript profiling of latex metabolism-related genes at the different stages of latex flow. In the present study, the expression pattern of 62 latex metabolism-related genes involved in water transportation, carbohydrate metabolism, natural rubber biosynthesis, hormone signaling, ROS generation and scavenging, and latex coagulum across three stages of latex flow between rubber tree clones CATAS7-33-97 and CATAS8-79 were comparatively analyzed by quantitative real-time PCR. The two clones show differences in latex regeneration and have a different duration of latex flow. The results showed that the expression levels of 38 genes were significantly higher in CATAS8-79 latex than in CATAS7-33-97 during latex regeneration, while 45 genes had a notably higher expression level in CATAS8-79 latex during latex flow. Together with the activation of the MEP pathway and jasmonate pathway in CATAS8-79 latex, HbPIP1;3, HbPIP1;4, HbSUT3, HbSus3, HbHMGS1-2, HbMK should contribute to the high latex regeneration ability. The up-regulation of ethylene signaling and Hb44KD and the down-regulation of latex coagulation-related genes in CATAS8-79 latex might contribute to its longer latex flow duration. This study provides some cues for revealing the regulation of latex metabolism in rubber trees.

  2. Development assessment of natural latex membranes: a new proposal for the treatment of amblyopia

    Energy Technology Data Exchange (ETDEWEB)

    Ribeiro, Jaqueline Alves; Rosa, Suelia Rodrigues Fleury, E-mail: jackalvesribeiro@gmail.com [Laboratorio de Engenharia e Biomaterial (BioEngLab), Faculdade Gama, Universidade de Brasilia (UnB), DF (Brazil); Leite, Cicilia Raquel Maia; Vasconcelos, Claudio Lopes; Soares, Joao Maria [Universidade do Estado do Rio Grande do Norte (UERN), Mossoro, RN (Brazil)

    2017-05-15

    The ophthalmic dysfunction amblyopia, commonly known as lazy eye, is characterized by decreased vision in one eye due to improper development in childhood. The aim of this study was to obtain and characterize natural rubber membranes and to assess their utility as an eye film capable of altering the passage of light. The latex membranes were produced using the Van Gogh method and the deposition technique and were analyzed by physical and chemical methods to determine the properties of latex in natura and of natural rubber membranes. The materials were characterized by X-ray diffractometry, scanning electron microscopy, thermogravimetry, differential scanning calorimetry, analysis of water sorption and light crossing analysis. We report here a new approach to the treatment of patients with amblyopia using latex membranes. (author)

  3. Development assessment of natural latex membranes: a new proposal for the treatment of amblyopia

    International Nuclear Information System (INIS)

    Ribeiro, Jaqueline Alves; Rosa, Suelia Rodrigues Fleury; Leite, Cicilia Raquel Maia; Vasconcelos, Claudio Lopes; Soares, Joao Maria

    2017-01-01

    The ophthalmic dysfunction amblyopia, commonly known as lazy eye, is characterized by decreased vision in one eye due to improper development in childhood. The aim of this study was to obtain and characterize natural rubber membranes and to assess their utility as an eye film capable of altering the passage of light. The latex membranes were produced using the Van Gogh method and the deposition technique and were analyzed by physical and chemical methods to determine the properties of latex in natura and of natural rubber membranes. The materials were characterized by X-ray diffractometry, scanning electron microscopy, thermogravimetry, differential scanning calorimetry, analysis of water sorption and light crossing analysis. We report here a new approach to the treatment of patients with amblyopia using latex membranes. (author)

  4. Technological properties of latex and natural rubber of Hevea brasiliensis clones Propriedades tecnológicas do látex e da borracha natural de clones de Hevea brasiliensis

    Directory of Open Access Journals (Sweden)

    Rogério Manoel Biagi Moreno

    2005-04-01

    Full Text Available Rubber industry has increased the requirements for quality and uniformity of natural rubber produced in Brazil. Technological properties of latex and natural rubber of clones GT 1, PB 235, IAN 873 and RRIM 600 [Hevea brasiliensis (Willd. Former Adr. de Juss. Muell.- Arg] were evaluated by standard methods of the dry rubber content (DRC%, percentage of nitrogen (N% and percentage of ashes (ASH% in two consecutive years; data were correlated with temperature and precipitation. Properties of latex and natural rubber varied (P A indústria da borracha está cada vez mais exigente em relação à qualidade e a uniformidade da borracha natural produzida no Brasil. Neste trabalho as propriedades tecnológicas do látex e da borracha natural dos clones de seringueira GT 1, PB 235, IAN 873 e RRIM 600 [Hevea brasiliensis (Willd. ex Adr. de Juss. Muell.-.Arg] foram avaliadas pelos ensaios padrões do conteúdo de borracha seca (DRC%, porcentagem de nitrogênio (N% e porcentagem de cinzas (CNZ% por dois anos consecutivos; os dados obtidos foram correlacionados com dados de temperatura e precipitação. As propriedades do látex e da borracha natural variaram (P < 0.01 em função do tipo de clone e entre coletas. O DRC% diminuiu no início da estação seca (maio a junho, enquanto N% e CNZ% aumentaram. O período de abril a junho revelou ser crítico, pois os valores da N% oscilaram acima 0,60%, fora dos padrões estabelecidos pela norma técnica brasileira ABNT/NBR. O clone RRIM 600 foi menos suscetível às variações climáticas.

  5. NR based curred latex material reclaimed with 2,2'-dibenzamidodiphenyldisulphide in truck tyre tread compound

    NARCIS (Netherlands)

    Rajan, V.V.; Dierkes, Wilma K.; Joseph, R.; Noordermeer, Jacobus W.M.

    2006-01-01

    It is observed that reclamation of natural rubber latex based rubber using 2,2'-dibenzamidodiphenyldisulphide as reclaiming agent is an optional methodology for recycling of waste latex rubber (WLR). For progressive replacement of virgin natural rubber by the reclaim, two alternatives curing system

  6. Performance Study of the Natural Rubber Composite with Clay Minerals

    International Nuclear Information System (INIS)

    Nyo Nyo Myint; Tin Tin Aye; Kyaw Myo Naing; Nyunt Wynn

    2008-03-01

    The preparation, characterization and some applications of natural rubber clay composite have been studied. This study investigated the possibility of natural rubber latex to replace some part of natural clays. In formulation of rubber clay composite from natural rubber latex and various clay minerals, three main steps were involved (i) preparation of latex cream (ii) prevulcanization of latex cream (iii) mixing vulcanized latex compound, with other ingredients. In each step, several parameters have been carefully investigated to optimize the performance of natural rubber clay composite production. The composite products were of better quality and can be considered to be more cost effective.

  7. Radiation induced graft copolymerization of acrylonitrile on natural rubber

    International Nuclear Information System (INIS)

    Claramma, N.M.; Mathew, N.M.; Thomas, E.V.

    1989-01-01

    Acrylonitrile graft natural rubber was prepared by initiating the polymerization of acrylonitrile in natural rubber field latex using γ-rays. The reaction was carried out at different rubber-monomer concentrations and the properties of the modified rubbers were compared with those of natural rubber and nitrile rubber. (author)

  8. Natural rubber producing plants: An overview | Venkatachalam ...

    African Journals Online (AJOL)

    ... Hevea and also other natural rubber producing species for alternative source of latex production in the near future. Keywords: Alternative rubber sources, biotechnology, breeding, Hevea brasiliensis, Parthenium argentatum, Taraxacum koksaghyz, Ficus bengalensis, Lactuca serriola. African Journal of Biotechnology Vol.

  9. Effect of irradiation on the prevulcanized latex/low nitrosamines latex blends

    Energy Technology Data Exchange (ETDEWEB)

    Ibrahim, Pairu; Zin, Wan Manshol Wan [Malaysian Nuclear Agency, 43000 kajang, Selangor (Malaysia); Daik, Rusli [Faculty of Science and Technology, Universiti Kebangsaan Malaysia,43600 bangi, Selangor (Malaysia)

    2015-09-25

    Radiation Prevulcanized Natural Rubber Latex (RVNRL) was blended with Low Nitrosamines Latex (LNL) at different composition ratio. Methyl Metachrylate (MMA) was added for grafting onto the blended latex. Blended latex was subjected to gamma irradiation at various doses up to 8kGy. The mechanical properties and FTIR analysis were investigated as a function of the blended composition and irradiation dose. It was found that blending at specific ratio and gamma irradiation at specific dose led to significant improvement on the properties of the latex. The optimum mechanical properties was attained at a total blending ratio of 70% RVNRL and 30% of LNL.

  10. Latex Allergy - A Case Report

    Directory of Open Access Journals (Sweden)

    Dr. Athma Prasanna

    2005-10-01

    Full Text Available The usage of rubber and its products are not uncommon in various walks of life. A continuous exposure or contact may sensitize the human body, causing reactions from mild to fatal. Despite the availability of the literature, medical personnel are still unaware of the implications of the use of latex materials.

  11. Latex production with depolymerizing compounds of actin cytoskeleton in rubber trees Produção de látex estimulada pela aplicação de compostos despolimerizantes de citoesqueleto de actina em seringueiras

    Directory of Open Access Journals (Sweden)

    Gao Zheng-Quan

    2008-02-01

    Full Text Available The objective of this work was to assess stimulated latex flow from rubber trees (Hevea brasiliensis with saturated macrolide (latrunculin A, 1, 5, and 10% potassium iodide in 2% methylcellulose compared with 0.3% ethylene in 2% methylcellulose (check and 2% methylcellulose (blank. Latex output and contents of pure rubber, total solid, sucrose, inorganic phosphorus, thiol, and Mg2+ were measured. The treatments containing 1% KI or saturated macrolide increased latex yields compared to the blank with 2% methylcellulose alone. The 1% KI or saturated macrolide treatments were equal to that of 0.3% ethylene check treatment. However, 5 and 10% KI were harmful to bark of rubber trees, even caused prolonged tapping panel dryness.O objetivo deste trabalho foi avaliar a produção de látex em seringueiras (Hevea brasiliensis estimulada pela aplicação de macrolídeo saturado (latrunculina A, iodeto de potássio a 1, 5 e 10%, e etileno a 0,3%, preparados em solução de metilcelulose a 0,2%. O tratamento testemunha consistiu da aplicação de solução pura de metilcelulose a 2%. Foram medidos a produção de látex e o conteúdo de borracha pura, sólidos totais, sacarose, fósforo inorgânico, tiol e Mg2+. A aplicação de KI a 1% ou de macrolídeo saturado aumentou a produção de látex em comparação com o tratamento testemunha. Os tratamentos com KI a 1% e macrolídeo saturado foram iguais ao tratamento com etileno a 0,3%. No entanto, os tratamentos com KI a 5 e 10% foram prejudiciais à casca da seringueira, causando até mesmo o secamento do painel-de-sangria.

  12. Latex improvement of recycled asphalt pavement

    Science.gov (United States)

    Drennon, C.

    1982-08-01

    The performance of a single unmodified milled recycled asphalt concrete was compared to milled asphalt concrete modified by addition of three types of rubber latex. Latex was added at 2, 3, 5, and 8 percent latex by weight of asphalt in the asphalt concrete. Lattices used were a styrene butadiene (SBR), a natural rubber (NR), an acrylonitrile butadiene (NBR), and four varieties of out of specification SBR lattices. Marshall tests, while indecisive, showed a modest improvement in properties of SBR and NR added material at 3 and 5 percent latex. Addition of NBR latex caused deterioration in Marshall stability and flow over that of control. Repeated load tests were run using the indirect tensile test, analyzed by the VESYS program, which computes life of pavements. Repeated load tests showed improvement in asphalt concrete life when 3 and 5 percent SBR was added. Improvement was also shown by the out of specification SBR.

  13. Greenhouse Gas Emissions from Rubber Industry in Thailand

    NARCIS (Netherlands)

    Jawjit, W.; Kroeze, C.; Rattanapan, S.

    2010-01-01

    Rubber production has been taking place in Thailand for many decades. Thailand is currently the world's largest natural rubber producer. We present emissions of greenhouse gases associated with the production of fresh latex, and three primary rubber products, including concentrated latex, block

  14. Practical Latex

    CERN Document Server

    Grätzer, George

    2014-01-01

    Accessible at 200+ pages to all who want to learn the practical usages of LaTeX Avoids technical subjects like font usage Friendly and easy to read, with many examples included Extra source materials include sample LaTeX files and suggestions for further reading

  15. A comparison of tackified, miniemulsion core-shell acrylic latex films with corresponding particle-blend films: structure-property relationships.

    Science.gov (United States)

    Canetta, Elisabetta; Marchal, Jeanne; Lei, Chun-Hong; Deplace, Fanny; König, Alexander M; Creton, Costantino; Ouzineb, Keltoum; Keddie, Joseph L

    2009-09-15

    Tackifying resins (TRs) are often added to pressure-sensitive adhesive films to increase their peel strength and adhesion energy. In waterborne adhesives, the TR is dispersed in water using surfactants and then blended with colloidal polymers in water (i.e., latex). In such waterborne systems, there are problems with the colloidal stability and difficulty in applying coatings of the particle blends; the films are often hydrophilic and subject to water uptake. Here, an alternative method of making waterborne, tackified adhesives is demonstrated. The TR is incorporated within the core of colloidal polymer particles via miniemulsion polymerization. Atomic force microscopy (AFM) combined with force spectroscopy analysis reveals there is heterogeneity in the distribution of the TR in films made from particle blends and also in films made from miniemulsion polymers. Two populations, corresponding to TR-rich and acrylic-rich components, were identified through analysis of the AFM force-displacement curves. The nanoscale maximum adhesion force and adhesion energy were found to be higher in a miniemulsion film containing 12 wt % tackifying resin in comparison to an equivalent blended film. The macroscale tack and viscoelasticity are interpreted by consideration of the nanoscale structure and properties. The incorporation of tackifying resin through a miniemulsion polymerization process not only offers clear benefits in the processing of the adhesive, but it also leads to enhanced adhesion properties.

  16. Radiation-grafting of acrylamide onto silicone rubber films for diclofenac delivery

    Science.gov (United States)

    Magaña, Hector; Palomino, Kenia; Cornejo-Bravo, Jose M.; Alvarez-Lorenzo, Carmen; Concheiro, Angel; Bucio, Emilio

    2015-02-01

    This work focuses on the pre-irradiation grafting of acrylamide (AAm) onto silicone rubber films (SR) and evaluates the effect of gamma-ray radiation conditions on the grafting yield, which in turn may influence the performance of the grafted materials as components of drug-eluting devices. Pristine and modified SR were characterized using FTIR-ATR, DSC, TGA, swelling, and water contact angle analysis in order to elucidate the effects of AAm grafting onto SR. Grafted films with content in AAm ranging from 0.81% to 22.20% showed excellent cytocompatibility against fibroblasts, and capability to uptake the anti-inflammatory drug diclofenac. Amount of drug loaded directly correlated with the grafting degree of the films. Drug release studies were performed at pH 7.4 and 37 °C (physiological conditions). Most grafted films released the drug in a sustained way for at least three hours.

  17. Latex medical gloves

    DEFF Research Database (Denmark)

    Palosuo, Timo; Antoniadou, Irini; Gottrup, Finn

    2011-01-01

    Many hospitals have implemented policies to restrict or ban the use of devices made of natural rubber latex (NRL) in healthcare as precautionary measures against the perceived risk of NRL allergy. Changes in glove technology, progress in measuring the specific allergenic potential of gloves...... properties of NRL and synthetic gloves and the role of glove powder. The review shows that NRL medical gloves, when compared with synthetic gloves, tend to be stronger, more flexible and better accepted by clinicians. The introduction of powder-free gloves has been associated with reductions in protein...

  18. Latex allergy in the workplace.

    Science.gov (United States)

    Toraason, M; Sussman, G; Biagini, R; Meade, J; Beezhold, D; Germolec, D

    2000-11-01

    While less than 1% of the general population is sensitized to latex, the U.S. Occupational Safety and Health Administration estimates that 8-12% of health-care workers are sensitized. The major source of workplace exposure is powdered natural rubber latex (NRL) gloves. NRL is harvested from HEVEA: brasiliensis trees and ammoniated to prevent coagulation resulting in the hydrolysis of the latex proteins. Prior to use in manufacturing, the latex is formulated by the addition of multiple chemicals. Thus, human exposure is to a mixture of residual chemicals and hydrolyzed latex peptides. Clinical manifestations include irritant contact dermatitis, allergic contact dermatitis (type IV), and type I immediate hypersensitivity response. Type I (IgE-mediated) NRL allergy includes contact urticaria, systemic urticaria, angioedema, rhinitis, conjunctivitis, bronchospasm, and anaphylaxis. Taking an accurate history, including questions on atopic status, food allergy, and possible reactions to latex devices makes diagnosis of type-I latex allergy possible. To confirm a diagnosis, either in vivo skin prick testing (SPT) or in vitro assays for latex-specific IgE are performed. While the SPT is regarded as a primary confirmatory test for IgE-mediated disease, the absence of a U.S. Food and Drug Administration-licensed HEVEA: brasiliensis latex extract has restricted its use in diagnosis. Serological tests have, therefore, become critically important as alternative diagnostic tests. Three manufacturers currently have FDA clearance for in vitro tests, to detect NRL-specific IgE. The commercially available assays may disagree on the antibody status of an individual serum, which may be due to the assay's detecting anti-NRL IgEs to different allergenic NRL proteins. Sensitized individuals produce specific IgE antibody to at least 10 potent HEVEA: allergens, Hev b 1-Hev b 10, each of which differs in its structure, size, and net charge. The relative content and ratios of Hevs in the

  19. Allergy to latex in health workers

    Directory of Open Access Journals (Sweden)

    Fajardo-Zapata, Álvaro L.

    2015-01-01

    Full Text Available Introduction: A common and growing problem in hospitals is hypersensitivity to rubber latex antigens, since many products, including gloves, are manufactured from this material, with the consequent possibility of producing allergy in persons who use them. Objective: To find out if health workers at a fourth level clinic in Bogotá, Colombia, are allergic to rubber latex, in relation to the use of gloves. Materials and methods: Descriptive, cross-sectional study of a non-probabilistic intentional-type sample in each one of four hospital units. A survey was applied to participants. Results: 16 of the 26 persons (61.5% with history of allergic processes manifested some kind of reaction when they had contact with latex gloves; the problem was more significant in the nursing personnel compared to physicians. Conclusions: The exposure to latex gloves may be generating the appearance of allergic occupational disease in health workers.

  20. Effect of the [TiO{sub 2}] on the radiation attenuation properties on the human tissue simulator obtained from radiovulcanized natural rubber latex; Efeito da [TiO{sub 2}] nas propriedades de atenuacao da radiacao no simulador de tecido humano obtido do latex de borracha natural radiovulcanizado

    Energy Technology Data Exchange (ETDEWEB)

    Tomimasu, Sumie; Guedes, Selma Matheus Loureiro [Instituto de Pesquisas Energeticas e Nucleares (IPEN), Sao Paulo, SP (Brazil). Centro de Tecnologia das Radiacoes]. E-mail: smguedes@net.ipen.br

    2002-07-01

    In this paper was studied the concentration effect of TiO{sub 2} used as filler in the radiation attenuation properties of human tissue simulator obtained from radio vulcanized natural rubber. The studied parameters were the following: the mass stopping power (S{sub mas}), the depth at maximum dose (Z{sub max}), the depth at 50% of maximum dose (R{sub 50}) the radiotherapeutic range (RR{sub 80}) and the electrons range (R). The natural rubber latex was formulated with [n-butyl acrylate ] = e phr and [KOH] = 0,2 phr and radio vulcanized by gamma rays (10 kGy) from {sup 60} Co source. The filler TiO{sub 2} was added (0-16 phr). The natural rubber slabs were obtained by casting method and theirs absorbed dose behavior was studied for each filler concentration using electrons beam (6 MeV) from an accelerator. The results showed that the addition of each phr of filler promoted the decrease of 0.019 cm for Z{sub max}, 0.021 cm for RR{sub 80}, 0.033 cm for R and 0.026 cm for R{sub 50} up to [Ti O{sub 2}] 15 phr. The S{sub mas} increased from 1.72 MeVcm2g-1 to 2.00 MeVcm2g-1 in the filler concentration range of 0-16 phr. The filler must be used in the 12-15 phr range. (author)

  1. Caracterização da hipersensibilidade a luvas de látex em profissionais da odontologia - DOI: 10.4025/actascihealthsci.v29i1.103 Rubber latex gloves hypersensitivities in dental workers - DOI: 10.4025/actascihealthsci.v29i1.103

    Directory of Open Access Journals (Sweden)

    Ana Maria Sell

    2007-12-01

    Full Text Available As reações alérgicas ao látex vêm aumentando em profissionais da saúde e se manifestam como um incômodo local ou sintomatologia sistêmica. Para conhecer a freqüência das manifestações alérgicas nos usuários de luvas de látex foi realizada busca entre os profissionais da odontologia via aplicação de questionários. Foram aplicados 450 questionários e, dentre os respondedores (140, 19% relataram manifestar reações locais ao contato com as luvas de látex e 5% reações sistêmicas a outros produtos de látex. Cerca de 2,5% declararam dermatite de contato e reações sistêmicas (anafiláticas, 1,5% apenas dermatite de contato e 1% sintomas de anafilaxia ao uso das luvas. Vinte por cento dos profissionais atenderam pacientes com alergia ao látex e 29% declararam questionar, durante a anamnese, a respeito de alergia ao látex. As reações alérgicas a luvas de látex foram freqüentes e é objeto de preocupação entre os profissionais da odontologia.Allergic reactions to natural rubber latex have increased in dental practice affecting both the professional and the patients. Allergic reactions may range from skin disease to asthma and anaphylaxis. This study aimed at determining the incidence of latex gloves allergy among dental care workers. 450 allergy questionnaires were used to collect information on latex gloves reactions and 140 dental works answered them. Latex gloves reaction occurred in 19% of them and 5% reported allergic reactions to other latex products. 2.5% reported symptoms suggesting contact dermatitis and anaphylaxis hypersensitivities, 1.5% contact dermatitis, and 1% reported anaphylaxis symptoms when wearing them. 20% of them had patients who presented symptoms suggestive of anaphylaxis hypersensitivity to rubber gloves latex. Our study confirms that rubber latex gloves reactions are frequent among dental care workers, and dentists must be aware of the latex allergy in dental practice.

  2. Synthesis and characterization of silver nanoparticles in natural rubber

    International Nuclear Information System (INIS)

    Abu Bakar, N.H.H.; Ismail, J.; Abu Bakar, M.

    2007-01-01

    Silver nanoparticles are formed in natural rubber matrix via photo reduction of film cast from natural rubber latex (NRL) containing silver salt. The resulting NR-Ag nanocomposite is characterized using TEM, XRD and UV spectroscopic techniques. The nanoparticles, diameter ranging between 4 and 10 nm, are dispersed within distinct interfaces which correspond to the inter-particle boundaries of the NRL particles that form the matrix. The average width of the interfaces is 8 nm. X-ray diffraction (XRD) analysis confirms the nanoparticles as metallic silver of the face-centered cubic type. UV-vis absorption spectra show peaks characteristic of the surface plasmon resonance of nano-sized silver. A comparison with the results of formation of silver, obtained under similar reduction condition, in a series of matrices namely de-proteinized natural rubber latex (DNRL), NRL containing sodium dodecyl sulfate (SDS), aqueous solutions of bovain serum albumin and SDS, suggests that the protein in natural rubber is responsible for the formation of stable silver nanoparticles in the natural rubber (NR) matrix

  3. Radiation-grafting of acrylamide onto silicone rubber films for diclofenac delivery

    International Nuclear Information System (INIS)

    Magaña, Hector; Palomino, Kenia; Cornejo-Bravo, Jose M.; Alvarez- Lorenzo, Carmen; Concheiro, Angel; Bucio, Emilio

    2015-01-01

    This work focuses on the pre-irradiation grafting of acrylamide (AAm) onto silicone rubber films (SR) and evaluates the effect of gamma-ray radiation conditions on the grafting yield, which in turn may influence the performance of the grafted materials as components of drug-eluting devices. Pristine and modified SR were characterized using FTIR-ATR, DSC, TGA, swelling, and water contact angle analysis in order to elucidate the effects of AAm grafting onto SR. Grafted films with content in AAm ranging from 0.81% to 22.20% showed excellent cytocompatibility against fibroblasts, and capability to uptake the anti-inflammatory drug diclofenac. Amount of drug loaded directly correlated with the grafting degree of the films. Drug release studies were performed at pH 7.4 and 37 °C (physiological conditions). Most grafted films released the drug in a sustained way for at least three hours. - Highlights: • SR–g-AAm depends on dose, monomer concentration, and reaction time and temperature. • Diclofenac sodium salt is loaded and released in a sustained way from SR–g-AAm films. • SR–g-AAm films are cytocompatible and have potential as components of drug–device

  4. Lignocellulosic fiber reinforced rubber composites

    CSIR Research Space (South Africa)

    Jacob John, Maya

    2009-04-01

    Full Text Available Natural Rubber (NR) is a naturally occurring elastomeric polymer of isoprene (2-methyl-1,3-butadiene). It can be extracted from latex of only one kind of tree, the Hevea braziliensis. Hevea rubber is produced in many tropical regions of Southeast...

  5. Incidence of latex harvesting technologies on agronomic and ...

    African Journals Online (AJOL)

    parameters and profitability of some rapid metabolic class clones of rubber ... of hormonal stimulation had no negative influence on the vegetative growth ..... yield (2597) was obtained with the control ..... metabolic energy of latex vessels as.

  6. Incidence of latex harvesting technologies on agronomic and ...

    African Journals Online (AJOL)

    Incidence of latex harvesting technologies on agronomic and physiological parameters and profitability of some rapid metabolic class clones of rubber tree ( Hevea brasiliensis ) in southwestern Côte d'Ivoire.

  7. Experimental study on the drying of natural latex medical gloves

    Science.gov (United States)

    Chankrachang, Mano; Yongyingsakthavorn, Pisit; Tohsan, Atitaya; Nontakaew, Udomkiat

    2018-01-01

    The purpose of this research was to study latex film drying at 70 °C using a laboratory drying oven. Two different total solid content (TSC) latex compounds, which 45% TSC and 35% TSC were used. The undried latex films were prepared according to the common procedures used in latex gloves manufacturers, that is, by dry coagulant dipping process. The experimental results such as initial moisture content, the amount of moisture and drying time of latex films in each latex compound formula were determined. After that, the results were projected to calculate on the production capacity expand by 1 million piece/day of natural latex medical gloves. Finally, the rate of moisture entering the latex drying oven and the energy consumption of the drying oven were estimated. The results indicated that when the 35% TSC of latex compound was used. The initial moisture content of latex film was higher than 45% TSC of latex compound about 7%. The drying time of 35% TSC was longer than 45% TSC for 2.5 min and consume more energy about 10%. As a result, the 45% TSC latex compound was the better way to saving energy and managing humidity in the production line. Therefore, it was found to very useful to an approximate design length and size of actual of latex drying oven and the rate of moisture entering the oven as well.

  8. Multi-objective optimization of process conditions in the manufacturing of banana (Musa paradisiaca L.) starch/natural rubber films.

    Science.gov (United States)

    Ramírez-Hernández, A; Aparicio-Saguilán, A; Reynoso-Meza, G; Carrillo-Ahumada, J

    2017-02-10

    Multi-objective optimization was used to evaluate the effect of adding banana (Musa paradisiaca L.) starch and natural rubber (cis-1,4-poliisopreno) at different ratios (1-13w/w) to the manufacturing process of biodegradable films, specifically the effect on the biodegradability, crystallinity and moisture of the films. A structural characterization of the films was performed by X-ray diffraction, Fourier transform infrared spectroscopy and SEM, moisture and biodegradability properties were studied. The models obtained showed that degradability vs. moisture tend to be inversely proportional and crystallinity vs. degradability tend to be directly proportional. With respect to crystallinity vs. moisture behavior, it is observed that crystallinity remains constant when moisture values remain between 27 and 41%. Beyond this value there is an exponential increase in crystallinity. These results allow for predictions on the mechanical behavior that can occur in starch/rubber films. Copyright © 2016 Elsevier Ltd. All rights reserved.

  9. Latex Allergy In Health Care Workers

    Directory of Open Access Journals (Sweden)

    Hayriye Sarıcaoğlu

    2013-05-01

    Full Text Available Background and Design: We aimed to determine the frequency of latex allergy in our hospital and to to evaluate the clinical and demographical features of the cases.Materials and Methods: A detailed questionnaire was administered to healthcare workers by a physician. Skin prick test with latex and patch test with rubber chemicals and a piece of latex glove were performed for all healthcare workers. Latex-specific IgE was measured in serum.Results: The study sample consisted of 36 nurses, 14 doctors, and 50 healthcare workers. While 46 subjects had symptoms, 54 subjects had no symptoms. The relationship of clinical disease with working duration, exposure duration (hour/day, history of atopy, and drug/food allergies was statistically significant. Five nurses and 1 healthcare worker had positive skin prick test. Two of them had positive latex-specific IgE. Positive skin prick test statistically significantly correlated with occupation, working duration, exposure duration (hour/day and positive latex-specific IgE. Two nurses and 2 healthcare workers had positive latex-specific IgE. Two of them had positive skin prick test. Positive latexspecific IgE statistically significantly correlated with working duration, exposure duration, and positive skin prick test. Patch test with a piece of latex glove was negative in all subjects. Three healthcare workers had positive patch test with thiuram-mix, one of them had also positive patch test with mercaptobenzothiazole.Discussion: One of the risk factors for latex allergy is occupations involving frequent exposure to latex products. Latex allergy should be taken into consideration if type I hypersensitivity reactions occur in occupational groups at risk for anaphylactic reaction.

  10. PLA and single component silicone rubber blends for sub-zero temperature blown film packaging applications

    Science.gov (United States)

    Meekum, Utai; Khiansanoi, Apichart

    2018-06-01

    The poly(lactic acid) (PLA) blend with single component silicone rubber in the presence of reactive amino silane coupling agent and polyester polyols plasticizer were studied. The manufacturing of film packaging for sub-zero temperature applications from the PLA blend was the main objective. The mechanical properties, especially the impact strengths, of PLA/silicone blends were significantly depended on the silicone loading. The outstanding impact strengths, tested at sub-zero temperature, of the blend having silicone content of 8.0 phr was achieved. It was chosen as the best candidate for the processability improvement. Adding the talc filler into the PLA/silicone blend to enhance the rheological properties was investigated. The ductility of the talc filled blends were decreased with increasing the filler contents. However, the shear viscosity of the blend was raised with talc loading. The blend loaded with 40 phr of talc filler was justified as the optimal formula for the blown film process testing and it was successfully performed with a few difficulties. The obtained blown film showed relative good flexibility in comparison with LDPE but it has low transparency.

  11. Structural characterization of rubber from jackfruit and euphorbia as a model of natural rubber.

    Science.gov (United States)

    Mekkriengkrai, Dararat; Ute, Koiichi; Swiezewska, Ewa; Chojnacki, Tadeusz; Tanaka, Yasuyuki; Sakdapipanich, Jitladda T

    2004-01-01

    A structural study of low molecular weight rubbers from Jackfruit (Artocarpus heterophyllus) and Painted spurge (Euphorbia heterophylla) was carried out as model compounds of natural rubber from Hevea brasiliensis. The rubber content of latex from Jackfruit was 0.4-0.7%, which is very low compared with that of 30-35% in the latex from Hevea tree. The rubber from Jackfruit latex was low molecular weight with narrow unimodal molecular weight distribution (MWD), whereas that obtained from E. heterophylla showed very broad MWD. The 1H and 13C NMR analyses showed that Jackfruit rubber consists of a dimethylallyl group and two trans-isoprene units connected to a long sequence of cis-isoprene units. The alpha-terminal group of Jackfruit rubber was presumed to be composed of a phosphate group based on the presence of 1H NMR signal at 4.08 ppm corresponding to the terminal =CH-CH2OP group.

  12. Troubleshooting for the observed problems in processing latex concentrate from natural resource

    International Nuclear Information System (INIS)

    Afreen, S; Haque, K R; Huda, M K

    2013-01-01

    Natural latex has special importance in the rubber industry for manufacturing different types of goods like gloves, balloons, male contraceptive and similar thin walled articles. This natural latex is much more sensitive a liquid to handle since it can easily become contaminated and thereby coagulated which makes it unfavourable for centrifuge and getting concentrate from it. Some other related measures also are included in consideration during the processing of concentrate latex from the natural raw latex. The problems that are being faced in a concentrate latex processing plant can be categorized in different groups like, problems related to the latex property, mechanical problems, electrical problems, handling and storage problems, transformation problems, problems related to environmental issues, etc. Among them, the most common and vital problems frequently observed in a concentrate latex processing plant are discussed here with a view to finding the measures for solution which will help to maintain the latex property in any latex processing plant.

  13. An evidence-based approach to medication preparation for the surgical patient at risk for latex allergy: is it time to stop being stopper poppers?

    Science.gov (United States)

    Heitz, James W; Bader, Stephen O

    2010-09-01

    The prevalence of latex allergy is increasing in surgical patient populations. Avoidance of exposure to the allergen is essential to minimizing perioperative complications in patients suspected to be at risk. Natural rubber latex has historically been ubiquitous in medical devices containing rubber. In 1998, the Food and Drug Administration (FDA) began to require the labeling of medical devices made from natural rubber latex; since that time substantial progress has been made in identifying latex-free alternatives. However, the rubber stoppers commonly found in pharmaceutical vial closures are exempt from FDA labeling requirements. Examination of the clinical and basic science literature regarding pharmaceutical vial closures supports limiting the rubber stopper to a single needle puncture as a safer practice, with the caveat that no strategy exists for the complete elimination of risk as long as stoppers made from natural rubber latex are used in pharmaceutical vials intended for human use. Copyright © 2010 Elsevier Inc. All rights reserved.

  14. Ultraviolet curing of acrylated liquid natural rubber for surface coating application

    OpenAIRE

    Kannikar Kwanming; Pairote Klinpituksa; Wae-asae Waehamad

    2009-01-01

    Ultraviolet curable acrylated liquid natural rubber was prepared by grafting of photosensitive molecule onto liquid natural rubber for surface coating application. The liquid natural rubber (LNR) was firstly obtained by degradation of natural rubber latex with hydrogen peroxide and cobalt acetylacetonate at 65oC for 72 hrs. The preparation of acrylated natural rubber was carried out by the reaction of acrylic acid and epoxidized liquid natural rubber (ELNR) prior obtained from LNR with formic...

  15. Review of food toxicological issues associated in rubber products

    OpenAIRE

    Ng, Mei Xiang; Ong, S.P.; Hii, C.L.; Chuah, L.A.; Law, C.L.

    2014-01-01

    Over the centuries, rubber latex gained its popularity in machinery application due to its unique thermal properties, high elasticity and excellent impact resistance. It is widely accepted in food industry as rubber has good resistance to chemicals, including acids, alkalis and salts. For instance, rubber components comprise of couplings, shields, dust covers, gaskets and seals exist as group or standalone component in food manufacturing equipments or machinery. Even though most of the rubber...

  16. Application of recombinant latex allergens in diagnostics of occupational latex allergy

    Directory of Open Access Journals (Sweden)

    Ewa Nowakowska-Świrta

    2015-02-01

    Full Text Available Over many years, allergy to natural rubber latex has been a major problem among health care workers (HCW. The diagnosis of occupational allergy requires methods of high diagnostic accuracy in view of certification implications (e.g., a sick worker quits a job. With the development of molecular methods, the frequency of application of recombinant allergens in the diagnostics of allergic diseases continues to increase. This paper reviews the applicability of laboratory tests which use recombinant allergens in the diagnostics of occupational allergy. The diagnosis of latex allergy is based on the presence of clinical symptoms linked with exposure to latex allergens, positive skin prick tests and detection of specific IgE antibodies to latex in serum. Moreover, in some cases specific challenge tests are conducted. The analysis of literature indicates that applying the panel of recombinant latex allergens in diagnostic tests, cross-reactivity can very likely be excluded and/or sensitization can be confirmed without the need for specific challenge tests, which in case of latex allergens carries a potential risk of generalized reactions. Med Pr 2015;66(1:85–97

  17. Preparation and Properties of Biocomposite Based on Natural Rubber and Bagasse Nanocellulose

    Directory of Open Access Journals (Sweden)

    Jarnthong Methakarn

    2015-01-01

    Full Text Available Biocomposite based on natural rubber (NR and bagasse nanocellulose (BNC was prepared in latex state. The mechanical, morphological and thermal properties of NR/BNC biocomposite were investigated. It was found that the addition of 3 wt% of BNC in NR film caused significant increase in modulus at 100% and 300% elongations and improved thermal stability of NR/BNC biocomposite. However, the strength at break and elongation at break of the biocomposite were not enhanced correlating to the morphological result obtained from scanning electron microscope (SEM.

  18. Biorefinery methods for separation of protein and oil fractions from rubber seed kernel

    NARCIS (Netherlands)

    Widyarani, R.; Ratnaningsih, E.; Sanders, J.P.M.; Bruins, M.E.

    2014-01-01

    Biorefinery of rubber seeds can generate additional income for farmers, who already grow rubber trees for latex production. The aim of this study was to find the best method for protein and oil production from rubber seed kernel, with focus on protein recovery. Different pre-treatments and oil

  19. Fatigue Performance and Multiscale Mechanisms of Concrete Toughened by Polymers and Waste Rubber

    Directory of Open Access Journals (Sweden)

    Bo Chen

    2014-01-01

    Full Text Available For improving bending toughness and fatigue performance of brittle cement-based composites, two types of water-soluble polymers (such as dispersible latex powder and polyvinyl alcohol powder and waste tire-rubber powders are added to concrete as admixtures. Multiscale toughening mechanisms of these additions in concretes were comprehensively investigated. Four-point bending fatigue performance of four series concretes is conducted under a stress level of 0.70. The results show that the effects of dispersible latex powder on bending toughness and fatigue life of concrete are better than those of polyvinyl alcohol powder. Furthermore, the bending fatigue lives of concrete simultaneously containing polymers and waste rubber powders are larger than those of concrete with only one type of admixtures. The multiscale physics-chemical mechanisms show that high bonding effect and high elastic modulus of polymer films as well as good elastic property and crack-resistance of waste tire-rubber powders are beneficial for improving bending toughness and fatigue life of cementitious composites.

  20. Rubber industry

    Science.gov (United States)

    Staszak, Maciej

    2018-03-01

    Following chapter presents short introductory description of rubber and rubber industry. The main problem of rubber industry is the way of the usage of spent tires. Furthermore very important group of problems arise considering the metal and nonmetal additives which are significant component of the vulcanized rubber. The key attention is dedicated to typical ways of rubber usage in utilization and recovery of metals from spent rubber materials concentrating specifically on used tires processing. The method of recovery of rare metals from rubber tires was described. The rubber debris finds widest use in the field of waste metal solutions processing. The environmental pollution caused by metals poses serious threat to humans. Several applications of the use of waste rubber debris to remove metals from environmental waters were described. Moreover, the agriculture usage of waste tire rubber debris is described, presenting systems where the rubber material can be useful as a soil replacement.

  1. Effect of pyrolysis atmospheres on the morphology of polymer-derived silicon oxynitrocarbide ceramic films coated aluminum nitride surface and the thermal conductivity of silicone rubber composites

    Science.gov (United States)

    Chiu, Hsien T.; Sukachonmakul, Tanapon; Wang, Chen H.; Wattanakul, Karnthidaporn; Kuo, Ming T.; Wang, Yu H.

    2014-02-01

    Amorphous silicon oxycarbide (SiOC) and silicon oxynitrocarbide (SiONC) ceramic films coated aluminum nitride (AlN) were prepared by using preceramic-polysilazane (PSZ) with dip-coating method, followed by pyrolysis at 700 °C in different (air, Ar, N2 and NH3) atmospheres to converted PSZ into SiOCair and SiONC(Ar,N2andNH3) ceramic. The existence of amorphous SiOCair and SiONC(Ar,N2andNH3) ceramic films on AlN surface was characterized by FTIR, XRD and XPS. The interfacial adhesion between silicone rubber and AlN was significantly improved after the introduction of amorphous SiOCair and SiONC(Ar,N2andNH3) ceramic films on AlN surface. It can be observed from AFM that the pyrolysis of PSZ at different atmosphere strongly affected to films morphology on AlN surface as SiOCair and SiONCNH3 ceramic films were more flat and smooth than SiONCN2 and SiONCAr ceramic films. Besides, the enhancement of the thermal conductivity of silicone rubber composites was found to be related to the decrease in the surface roughness of SiOCair and SiONC(Ar,N2andNH3) ceramic films on AlN surface. This present work provided an alternative surface modification of thermally conductive fillers to improve the thermal conductivity of silicon rubber composites by coating with amorphous SiOCair and SiONC(Ar,N2andNH3) ceramic films.

  2. Latex in the Hospital Environment

    Science.gov (United States)

    LATEX in the Hospital Environment Updated Fall 2015 This list provides a guide to some of the most common objects containing latex and offers some ... remover–Sepha Pharm) 1 LATEX in the Hospital Environment (continued) Frequently contains LATEX OR/Infection Control masks, ...

  3. Pengaruh Konsentrasi Amonium Laurat Terhadap Kekuatan Tarik dan Kemuluran serta Ketahanan Sobek Film Lateks Karet Alam

    OpenAIRE

    Hussudur, Misbah

    2011-01-01

    An investigation about the influence of ammonium laurate concentration to natural rubber latex film was obtained using the immersion method. The variation of ammonium laurate concentration was used 0%; 0,05%; 0,07%; and 0,09% with vulcanization time used was for 30 minutes and vulcanization temperature was used 1000C. The physics characteristic witch analized were tensile strength, elongation and tear strength and the structure of resulting surfaces were tested with analysis of SEM. rom this ...

  4. Observações sôbre a produtividade de seringueiras (Hevea brasiliensis muell.-arg. Plantadas de sementes: IV - Produtividade de 29 plantas existentes na travessa Itororó, Belém, Pá Observations on the latex production of seedlings of rubber trees (Hevea brasiliensis muell.-arg.: IV - Study of 29 rubber trees of the travessa Itororó, Belém, Pará

    Directory of Open Access Journals (Sweden)

    Luiz O. T. Mendes

    1960-01-01

    Full Text Available Neste trabalho são apresentados os resultados do estudo da produtividade de 29 seringueiras plantadas de sementes, existentes na Travessa Itororó, Belém, quando tinham a idade de 25 anos aproximadamente. Os resultados se referem à produção obtida de sangrias feitas a meia espiral, em dois regimes de trabalho: a em dias alternados, de 16 de setembro de 1943 a 31 de março de 1944; b todos os dias úteis, de 1.° de abril a 30 de setembro de 1944. Do conjunto de seringueiras estudadas os resultados mostram que a melhor planta logo após as primeiras sangrias já se classificara em primeiro lugar, quanto à produção. Os dados revelam também que houve pequena diminuição na produção média da população, ao passar para o regime de sangria diária; observou-se no entanto, que o decréscimo de produção foi mois pronunciado e freqüente entre as plantas de maior produtividade médio no regime de sangria em dias alternados. O estudo da população como um todo mostra que uma pequena parcela das plantas contribuiu com grande parte da produção; em ambos os regimes de trabalho, cerca de 25% da população de plantas foram responsáveis por aproximadamente 50% do produção de látex, e mais ou menos 50% da população de plantas produziram cerca de 75% da produção de látex. Tais resultados mostram a importância que se deve dar à eliminação precoce de plantas pouco produtivas, no caso de se fazerem plantações a partir de sementes não selecionadas.The results of 13 month tappings (half-spiral cut of 29 seedlings of rubber trees, approximately 25 years old, ore presented. From September 16, 1943 to March 31, 1944, the trees were tapped every other day; from Abril 1st, to September 30, 1944, every day. The change of the tapping system, from every other day to daily, caused a small decrease in the mean yield of the group, per tapping; this yield decrease was more pronounced and frequent in the high production plants. It must be

  5. Syntheses of crosslinked latex nanoparticles using differential microemulsion polymerization

    Science.gov (United States)

    Hassmoro, N. F.; Rusop, M.; Abdullah, S.

    2013-06-01

    The differential microemulsion polymerization was used to synthesize latex nanoparticles. In this paper, 1, 3-butylene glycol dimethacrylate (1, 3-BGDMA) was used as a crosslinker respectively 1-5 weight% of monomer total. Butyl acrylate (BA), butyl methacrylate (BMA), and methacrylic acid (MAA) was used as the monomer. The thin film of latex nanoparticles were prepared by using spin coating method and have been dried at 100°C for 5 minutes. The amount of the crosslinker added in the polymerization was optimized and we found that the particle sizes fall in the range of 30-60 nm. The structural morphology of the uncrosslinked latex represented the most homogeneous image compared to the crosslinked latex. The effect of the amount of crosslinker on the particle sizes investigated by the Zeta-sizer Nano series while Atomic Force microscopy (AFM) was used to study the structural properties of latex nanoparticles.

  6. Syntheses of crosslinked latex nanoparticles using differential microemulsion polymerization

    International Nuclear Information System (INIS)

    Hassmoro, N F; Abdullah, S; Rusop, M

    2013-01-01

    The differential microemulsion polymerization was used to synthesize latex nanoparticles. In this paper, 1, 3-butylene glycol dimethacrylate (1, 3-BGDMA) was used as a crosslinker respectively 1–5 weight% of monomer total. Butyl acrylate (BA), butyl methacrylate (BMA), and methacrylic acid (MAA) was used as the monomer. The thin film of latex nanoparticles were prepared by using spin coating method and have been dried at 100°C for 5 minutes. The amount of the crosslinker added in the polymerization was optimized and we found that the particle sizes fall in the range of 30–60 nm. The structural morphology of the uncrosslinked latex represented the most homogeneous image compared to the crosslinked latex. The effect of the amount of crosslinker on the particle sizes investigated by the Zeta-sizer Nano series while Atomic Force microscopy (AFM) was used to study the structural properties of latex nanoparticles.

  7. The patatin-like protein from the latex of Hevea brasiliensis (Hev b 7) is not a vacuolar protein

    NARCIS (Netherlands)

    Jekel, PA; Hofsteenge, J; Beintema, JJ

    Upon centrifugation, rubber latex is divided into a layer of rubber particles, the cytosol, and the lutoid-body fraction, which is of vacuolar origin. One of the proteins isolated from the lutoid-body fraction is a protein with a molecular mass of 43 kDa, which has esterase activity on

  8. Development of rubber gloves by radiation vulcanization

    International Nuclear Information System (INIS)

    Makuuchi, K.; Yoshii, F.; Ishigaki, I.; Mogi, M.; Saito, T.

    1990-01-01

    The processes of radiation vulcanization and production of protective rubber gloves for radioactive contamination are described. A newly developed sensitizing system consisting of 5 phr 2-ethylhexyl acrylate and 1 phr carbon tetrachloride was used to vulcanize natural rubber latex at 12 kGy. Transparent and soft gloves were obtained from the radiation vulcanized latex by a coagulant dipping process. The mechanical properties of the gloves meet Japanese Industrial Standard specification for protective gloves. Combustion analysis of the gloves revealed that the amount of evolved sulfur dioxide and remaining ashes are less than those from commercially available rubber gloves. A trial usage of the gloves at a nuclear power plant showed that the gloves were easy to use for delicate work without undergoing fatigue. (author)

  9. Latex allergy and occupational asthma in health care workers: adverse outcomes.

    OpenAIRE

    Amr, Sania; Bollinger, Mary E.

    2004-01-01

    The prevalence of natural rubber latex (NRL) allergy has been estimated to be 5-18% in health care workers, and latex exposure has been one of the leading causes of occupational asthma in the last several years. We present the cases of two nurses who developed sensitivity to NRL, both with dermatologic symptoms and respiratory symptoms that included asthma. They were referred to the University of Maryland for evaluation of their allergies, then for occupational and environmental consults. The...

  10. Adhesion to silicone rubber of yeasts and bacteria isolated from voice prostheses : Influence of salivary conditioning films

    NARCIS (Netherlands)

    Busscher, HJ; GeertsemaDoornbusch, GI; vanderMei, HC

    Adhesion of yeasts and bacteria to silicone rubber is one of the first steps in the biodeterioration of silicone rubber voice prostheses. In this paper, adhesion of two streptococcal, staphylococcal, Candida albicans and Candida tropicalis strains, isolated from explanted voice prostheses was

  11. Pilot scale experiments on radiation vulcanization of NR latex

    Science.gov (United States)

    Ridwan, M.

    The potential of irradiated latex as raw material of commercial use is under testing on pilot plant scale in Indonesia which has 225 kCi Co-60 irradiation facility and can irradiate 1000 tonnes of centrifuged latex per annum. The facility was jointly designed by BATAN of Indonesia and JAERI of Japan and was jointly financed by UNDP/IAEA, Government of Japan and Government of Indonesia under UNDP/IAEA Regional Cooperative Agreement Project on Industrial Application of Isotopes and Radiation Technology. The facility is a water pool type and can accomodate 400 kCi Co-60. The Co-60 rack has two shapes, plate and cylindrical shapes. The plate shape source is used for natural rubber latex irradiation and the cylindrical one is used for other irradiation services. The vulcanization system consists of three major components : emulsification unit ( height : 650 mm, diameter 500 mm ), mixing unit ( height : 1900mm, diameter 1200 mm ) and vulcanization reactor ( height : 1800 mm, diameter 1300 mm ). The first two components are located outside shielded room while the third one-in irradiation room. The radiation vulcanization process is a much simpler energy saving process comparedto the conventional thermal process which has two vulcanization steps before and after dipping. The physical and mechanical properties of irradiated NR Latex are comparable to those of sulfur vulcanized, and depend on many factors such as irradiation dose, sensitizer content, dry rubber content and storage time.

  12. CDNA library from the Latex of Hevea brasiliensis

    Directory of Open Access Journals (Sweden)

    Wilaiwan Chotigeat

    2010-12-01

    Full Text Available Latex from Hevea brasiliensis contains 30-50% (w/w of natural rubber (cis-1,4-polyisoprene, the important rawmaterial for many rubber industries. We have constructed a cDNA library from the latex of H. brasiliensis to investigate theexpressed genes and molecular events in the latex. We analyzed 412 expressed sequence tags (ESTs. More than 90% of theEST clones showed homology to previously described sequences in public databases. Functional classification of the ESTsshowed that the largest category were proteins of unknown function (30.1%, 11.4% of ESTs encoded for rubber synthesisrelatedproteins (RS and 8.5% for defense or stress related proteins (DS. Those with no significant homology to knownsequences (NSH accounted for 8.7%, primary metabolism (PM and gene expression and RNA metabolism were 7.8% and6.6%, respectively. Other categories included, protein synthesis-related proteins (6.6%, chromatin and DNA metabolism(CDM 3.9%, energy metabolism (EM 3.4%, cellular transport (CT 3.2%, cell structure (CS 3.2%, signal transduction (ST2.2%, secondary metabolism (SM 1.7%, protein fate (PF 2.2%, and reproductive proteins (RP 0.7%.

  13. Latex and friends

    CERN Document Server

    Dongen, M R C van

    2012-01-01

    LaTeX is a free, automated state-of-the-art typesetting system. This book teaches all the ins and outs of LaTeX which are needed to write an article, report, thesis, or book. The book teaches by example, giving many worked out examples showing input and output side by side. The book presents the most recent techniques for presenting data plots, complex graphics, and computer presentations, but does not require previous knowledge. However, it is also a reference for the more seasoned user, with pointers to modern techniques and packages. Recurring themes in the book are consistent and effective

  14. More math into Latex

    CERN Document Server

    Grätzer, George

    2007-01-01

    For close to two decades, Math into Latex has been the standard introduction and complete reference for writing articles and books containing mathematical formulas. In this fourth edition, the reader is provided with important updates on articles and books. An important new topic is discussed: transparencies (computer projections). Key features of More Math into Latex, 4th edition: Installation instructions for PC and Mac users; An example-based, visual approach and a gentle introduction with the Short Course; A detailed exposition of multiline math formulas with a Visual Guide; A unified appr

  15. Natural rubber (NR) biosynthesis: perspectives from polymer chemistry

    Energy Technology Data Exchange (ETDEWEB)

    Barkakaty, Balaka [ORNL

    2014-01-01

    Natural rubber is an important strategic raw material for manufacturing a wide variety of industrial products. There are at least 2,500 different latex-producing plant species; however, only Hevea brasiliensis (the Brazilian rubber tree) is a commercial source. The chemical structure of natural rubber is cis-1,4-polyisoprene, but the exact structure of the head and end groups remains unknown. Since synthetic cis-1,4-polyisoprenes cannot match the superior properties of natural rubber, understanding the chemistry behind the biosynthetic process is key to finding a possible replacement. T his chapter summarizes our current understandings from the perspective of a polymer scientist by comparing synthetic polyisoprenes to natural rubber. The chapter also highlights biomimetic polymerization, research towards a synthetic match of natural rubber and the role of natural rubber in health care.

  16. Preparation of vinyl acetate grafted natural rubber by irradiation method

    Energy Technology Data Exchange (ETDEWEB)

    Porntrairat, A.; Pattamaprom, C. [Center of Excellence on Natural Rubber Technology, Department of Chemical Engineering, Faculty of Engineering, Thammasat University, Pathumthani 12120 (Thailand)

    2016-03-09

    Improvement in properties of natural rubber could be done by several methods. In this research, gamma radiation technique, which is simple, accurate, easy to control and clean, was applied to enhance the properties of natural rubber (NR) in latex state. The purpose of this research is to study the appropriate condition for preparing grafted natural rubber latex by using irradiation method. Vinyl acetate monomers (VAc) were grafted onto natural rubber latex (NR-g-PVAc) at 0-10 kGys by gamma radiation from Cobalt-60 source at room temperature. Physical properties of grafted natural rubber such as chloroform number, swelling ratio and gel content were measured. The VAc content of NR-g-PVAc was investigated by titration and visualized by FTIR spectroscopy. The FTIR spectra of NR-g-PVAc prepared at 0-10 kGys showed characteristic peaks of the vinyl acetate confirming that VAc could be grafted onto natural rubber molecular chains effectively under appropriate irradiation conditions. From the result, radiation grafting was found to be a useful technique for grafting of vinyl acetate onto natural rubber.

  17. Involvement of Ethylene in the Latex Metabolism and Tapping Panel Dryness of Hevea brasiliensis

    Science.gov (United States)

    Putranto, Riza-Arief; Herlinawati, Eva; Rio, Maryannick; Leclercq, Julie; Piyatrakul, Piyanuch; Gohet, Eric; Sanier, Christine; Oktavia, Fetrina; Pirrello, Julien; Kuswanhadi; Montoro, Pascal

    2015-01-01

    Ethephon, an ethylene releaser, is used to stimulate latex production in Hevea brasiliensis. Ethylene induces many functions in latex cells including the production of reactive oxygen species (ROS). The accumulation of ROS is responsible for the coagulation of rubber particles in latex cells, resulting in the partial or complete stoppage of latex flow. This study set out to assess biochemical and histological changes as well as changes in gene expression in latex and phloem tissues from trees grown under various harvesting systems. The Tapping Panel Dryness (TPD) susceptibility of Hevea clones was found to be related to some biochemical parameters, such as low sucrose and high inorganic phosphorus contents. A high tapping frequency and ethephon stimulation induced early TPD occurrence in a high latex metabolism clone and late occurrence in a low latex metabolism clone. TPD-affected trees had smaller number of laticifer vessels compared to healthy trees, suggesting a modification of cambial activity. The differential transcript abundance was observed for twenty-seven candidate genes related to TPD occurrence in latex and phloem tissues for ROS-scavenging, ethylene biosynthesis and signalling genes. The predicted function for some Ethylene Response Factor genes suggested that these candidate genes should play an important role in regulating susceptibility to TPD. PMID:26247941

  18. Study on the Secant Segmentation Algorithm of Rubber Tree

    Science.gov (United States)

    Li, Shute; Zhang, Jie; Zhang, Jian; Sun, Liang; Liu, Yongna

    2018-04-01

    Natural rubber is one of the most important materials in the national defense and industry, and the tapping panel dryness (TPD) of the rubber tree is one of the most serious diseases that affect the production of rubber. Although considerable progress has been made in the more than 100 years of research on the TPD, there are still many areas to be improved. At present, the method of artificial observation is widely used to identify TPD, but the diversity of rubber tree secant symptoms leads to the inaccurate judgement of the level of TPD. In this paper, image processing technology is used to separate the secant and latex, so that we can get rid of the interference factors, get the exact secant and latex binary image. By calculating the area ratio of the corresponding binary images, the grade of TPD can be classified accurately. and can also provide an objective basis for the accurate identification of the tapping panel dryness (TPD) level.

  19. Latex Imaging by Environmental STEM: Application to the Study of the Surfactant Outcome in Hybrid Alkyd/Acrylate Systems

    OpenAIRE

    Faucheu , Jenny; Chazeau , Laurent; Gauthier , Catherine; Cavaille , Jean-Yves; Goikoetxea , Monika; Minari , Roque; Asua , Jose M.

    2009-01-01

    International audience; Among other uses. latexes are a successful alternative to solvent-borne binders for coatings. Efforts are made to produce hybrid nanostructured latexes containing an acrylic phase and an alkyd phase, However, after the film-forming process, the surfactant used to stabilize these latexes remains in the film, and its location can have a drastic effect on the application properties. Among the processing parameters, the alkyd hydrophobicity can strongly influence this loca...

  20. The working of RVNRL pilot plant of Rubber Board and it's safety devices

    International Nuclear Information System (INIS)

    Britto, I.J.; Thomas, E.V.

    1996-01-01

    A pilot plant for producing radiation vulcanized natural rubber latex (RVNRL) was established at Rubber Board, India in 1992. Irradiation is done by a batch process in the plant. The plant has a versatile safety system for safety of operators and people working in and around the plant

  1. Reinforcing Natural Rubber with Cellulose Nanofibrils Extracted from Bleached Eucalyptus Kraft Pulp

    Science.gov (United States)

    Chunmei Zhang; Tianliang Zhai; Ronald Sabo; Craig Clemons; Yi Dan; Lih-Sheng Turng

    2014-01-01

    Reinforced natural rubber (NR) nanocomposites were prepared by solution mixing, casting, and evaporation of pre-vulcanized natural rubber latex and an aqueous suspension of cellulose nanofibrils (CNFs) extracted from bleached eucalyptus kraft pulp. Scanning electron microscopy (SEM) images showed that there were no micro-scaled aggregates observed in the nanocomposites...

  2. THE EFFLUENT OF NATURAL-RUBBER FACTORIES IS ENRICHED IN THE ANTIFUNGAL PROTEIN HEVEIN

    NARCIS (Netherlands)

    SOEDJANAATMADJA, UMS; SUBROTO, T; BEINTEMA, JJ

    1995-01-01

    Hevein is a small cystine-rich protein with a polypeptide chain length of 43 residues. It occurs in the lutoid body fraction of rubber latex, has affinity for chitin, and inhibits fungal growth. It was isolated from the effluent of a rubber factory in a yield of about 0.7 g/l. The elution position

  3. Crystallization of Hevamine, an Enzyme with Lysozyme/Chitinase Activity from Hevea brasiliensis Latex

    NARCIS (Netherlands)

    ROZEBOOM, HJ; BUDIANI, A; BEINTEMA, JJ

    1990-01-01

    Hevamine, an enzyme with both lysozyme and chitinase activity, was isolated and purified from Hevea brasiliensis (rubber tree) latex. The enzyme (molecular weight 29,000) is homologous to certain “pathogenesis-related” proteins from plants, but not to hen egg-white or phage T4 lysozyme. To

  4. Towards anti-corrosion coatings from surfactant-free latexes based on maleic anhydride containing polymers

    NARCIS (Netherlands)

    Soer, W.J.; Ming, W.; Koning, C.E.; Benthem, van R.A.T.M.

    2008-01-01

    We report on the film formation of surfactant-free, artificial latexes based on copolymers containing maleic anhydride. Different metallic substrates, such as aluminum, steel and magnesium alloys, were coated with three different latexes. A commercial polyester based coating was used as a

  5. Rubber Reclamation

    Science.gov (United States)

    Williams, Kathryn R.

    2007-01-01

    The safety and health hazards related to recycling of used rubber, due to the scarcity and high price of virgin rubber are reported. Various threats like stagnant water pools trapped in tires leading to diseases and ignited tires, which become very difficult to extinguish and generating smoke that is extremely detrimental to the environment, have…

  6. On the response of rubbers at high strain rates.

    Energy Technology Data Exchange (ETDEWEB)

    Niemczura, Johnathan Greenberg (University of Texas-Austin)

    2010-02-01

    In this report, we examine the propagation of tensile waves of finite deformation in rubbers through experiments and analysis. Attention is focused on the propagation of one-dimensional dispersive and shock waves in strips of latex and nitrile rubber. Tensile wave propagation experiments were conducted at high strain-rates by holding one end fixed and displacing the other end at a constant velocity. A high-speed video camera was used to monitor the motion and to determine the evolution of strain and particle velocity in the rubber strips. Analysis of the response through the theory of finite waves and quantitative matching between the experimental observations and analytical predictions was used to determine an appropriate instantaneous elastic response for the rubbers. This analysis also yields the tensile shock adiabat for rubber. Dispersive waves as well as shock waves are also observed in free-retraction experiments; these are used to quantify hysteretic effects in rubber.

  7. Enzymatic synthesis of rubber polymer in Hevea brasiliensis

    Energy Technology Data Exchange (ETDEWEB)

    Tang, F.; Hu, S.; Benedict, C.R. (Texas A and M Univ., College Station (United States))

    1991-05-01

    Light and Dennis purified serum soluble rubber transferase from Hevea latex to homogeneity. Prenyl transferase co-purified with rubber transferase. In the absence of washed rubber particles (WRP) the prenyl transferase catalyzed the formation of trans FPP from DMAPP and IPP. In the presence of WRP the transferase catalyzed cis additions of IPP to pre-existing rubber chains. Control mixtures of WRP, Mg{sup 2+} and FPP were not included to test for the contributions of the bound rubber transferase on WRP to the incorporation of IPP into polyisoprene. Bound rubber transferase catalyzes the repetitive addition of IPP to allylic-PP starter molecules to form polyisoprene. The order of utilization of allylic-PP starters was GGPP > FPP > GPP > DMAPP. The authors have shown that the polyisoprene enzymatically synthesized on WRP is a bimodal polymer consisting of different mol wt rubber chains similar to the polymeric characteristics of natural rubber. The bound rubber transferase was solubilized with Chaps and purified on DEAE-cellulose. The polymerization reaction catalyzed by the purified preparation showed a 98% requirement for pre-existing rubber chains. Results suggest that the prenyl transferase from Hevea serum may be part of the polymer starter system furnishing allylic-PP for the bound rubber transferase.

  8. Pilot scale experiments on radiation vulcanization of NR latex

    International Nuclear Information System (INIS)

    Ridwan, M.

    1985-01-01

    The potential of irradiated latex as raw material of commercial use is under testing on pilot plant scale in Indonesia which has 225 kCi Co-60 irradiation facility and can irradiate 1000 tonnes of centrifuged latex per annum. The facility was jointly designed by BATAN of Indonesia and JAERI of Japan and was jointly financed by UNDP/IAEA, Government of Japan and Government of Indonesia under UNDP/IAEA Regional Cooperative Agreement Project on Industrial Application of Isotopes and Radiation Technology. The facility is a water pool type and can accommodate 400 kCi Co-60. The Co-60 rack has two shapes, plate and cylindrical shapes. The plate shape source is used for natural rubber latex irradiation and the cylindrical one is used for other irradiation services. The vulcanization system consists of three major components: emulsification unit, mixing unit and vulcanization reactor. The first two components are located outside shielded room while the third one in irradiation room. The radiation vulcanization process is a much simpler energy saving process compared to the conventional thermal process which has two vulcanization steps before and after dipping. The physical and mechanical properties of irradiated NR latex are comparable to those of sulfur vulcanized. (author)

  9. Effect of rootstock on the scion of Hevea brasiliensis through metabolic analysis of latex samples by 1H NMR

    Directory of Open Access Journals (Sweden)

    Eduardo Sanches Pereira do Nascimento

    2011-01-01

    Full Text Available In this study, the effect of rootstock on grafting through metabolomic analysis of latex (Hevea brasiliensis samples was verified by 1H nuclear magnetic resonance (NMR and multivariate data analysis. Sixteen metabolites present in the latex cytosol were characterized by NMR. PCA analysis showed that the latex samples of the RR and GR groups can be differentiated. The GR group samples present a metabolic profile similar to the RR group samples, while the RG group is in an intermediate position between RR and GG groups. Sucrose and formate contributed greatly to the separation obtained by PCA, presenting a good correlation between the results. 1H NMR was an efficient technique to differentiate latex samples from different types of rootstocks and grafting and in the future could be used to predict rubber production by latex analysis.

  10. Latex imaging by environmental STEM: application to the study of the surfactant outcome in hybrid alkyd/acrylate systems.

    Science.gov (United States)

    Faucheu, Jenny; Chazeau, Laurent; Gauthier, Catherine; Cavaillé, Jean-Yves; Goikoetxea, Monika; Minari, Roque; Asua, José M

    2009-09-01

    Among other uses, latexes are a successful alternative to solvent-borne binders for coatings. Efforts are made to produce hybrid nanostructured latexes containing an acrylic phase and an alkyd phase. However, after the film-forming process, the surfactant used to stabilize these latexes remains in the film, and its location can have a drastic effect on the application properties. Among the processing parameters, the alkyd hydrophobicity can strongly influence this location. This article aims at the imaging of these surfactant molecules in two hybrid latexes with different hydrophobicity level of the alkyd resin. A first part of this paper is dedicated to the understanding of the contrast provided by the surfactant in environmental STEM imaging of latexes. Then, the influence of surfactant-polymer affinity on the surfactant location after film-forming of those hybrid alkyd/acrylate latexes is studied by this technique. It is shown that in the hybrid latex with an alkyd shell (obtained with the most hydrophilic resin), the surfactant molecules tend to remain buried in the alkyd phase. Conversely, in the hybrid latex with an acrylate shell (in the case of the most hydrophobic resin), the surfactant molecules tend to gather into islands like in pure acrylate latex films.

  11. Study of Antibacterial Activity and Bacteriology of Latex from Asclepias syriaca L

    Science.gov (United States)

    McCay, Steven; Mahlberg, Paul

    1973-01-01

    Whole and fractionated latex of Asclepias syriaca was tested for antimicrobial or growth-promoting activity with 16 genera and species of bacteria. Latex and extracted fractions (distilled water, acetic acid, sodium bicarbonate, sulfuric acid, and ethyl ether) possessed no detectable antimicrobial activity. Comparison of growth curves of selected bacteria incubated with serum and rubber fractions, as well as controls, revealed no detectable inhibition of growth, except for a slight inhibitory response to autoclaved serum. Most bacteria were capable of utilizing latex for a substrate as indicated by the increased growth rate in the exponential phase. The stationary phase was entered simultaneously by both the treated cultures and the controls. Various bacteria cultured in a litmus latex mixture yielded populations which ranged from <104 organisms/ml for Lactobacillus casei, Staphylococcus aureus and Micrococcus lysodeikticus to 1.1 × 1010 organisms/ml for Clostridium acetobutylicum. Whole latex, as well as the serum and rubber fractions, support the growth of various bacteria, but under field conditions there is no evidence for systemic infection of this type of cell by bacteria. PMID:4790590

  12. Latex allergy: new insights to explain different sensitization profiles in different risk groups.

    Science.gov (United States)

    Peixinho, C; Tavares-Ratado, P; Tomás, M R; Taborda-Barata, L; Tomaz, C T

    2008-07-01

    Differences in latex allergen sensitization profiles have been described between children subjected to repetitive surgical interventions and health care workers (HCW). 'Major' allergens for patients with spina bifida are Hev b 1, 3 and 7, while for HCW, 'major' allergens are Hev b 2, 5, 6.01 and 13. The reason for these differential sensitization profiles is currently unknown. To investigate latex allergen profiles on internal and external surfaces of natural rubber latex gloves. Eighty-two samples of commonly used surgical gloves (41 glove brands) were used for analysis. Specific allergen levels of Hev b 1, 3, 5 and 6.02 on both surfaces of the gloves were quantified using an enzyme immunometric assay, a FITkit (FIT Biotech, Tampere, Finland). Differences in allergen levels were observed between internal and external surfaces of all glove types. Concentrations of Hev b 1 and Hev b 3 were significantly higher on external surfaces, while internal surfaces had higher allergen levels of Hev b 5 and Hev b 6.02. Analysis of surgical and examination gloves, powdered and nonpowdered gloves also showed that the content of Hev b 5 and Hev b 6.02 was significantly higher on internal surfaces while that of Hev b 1 and Hev b 3 was higher on external surfaces. Our study showed different allergen profiles on internal and external surfaces of natural rubber latex gloves. These results may suggest a relationship between latex allergen localization and sensitization routes in different risk groups.

  13. Mechanical Properties of Graphene-Rubber Nanocomposites

    Science.gov (United States)

    Anhar, N. A. M.; Ramli, M. M.; Hambali, N. A. M. A.; Aziz, A. A.; Mat Isa, S. S.; Danial, N. S.; Abdullah, M. M. A. B.

    2017-11-01

    This research focused on development of wearable sensor device by using Prevulcanized Natural Rubber (PV) and Epoxidized Natural Rubber (ENR 50) latex incorporated with graphene oxide (GO), graphene paste, graphene powder and reduced graphene oxide (rGO) powder. The compounding formulation and calculation were based on phr (parts per hundred rubber) and all the samples were then tested for mechanical properties using Instron 5565 machine. It was found that the sonication effects on tensile strength may have better quality of tensile strength compared to non-sonicated GO. For PV incorporate GO, the optimum loading was best determined at loading 1.5 phr with or without sonication and similar result was recorded for PV/G. For ENR 50 incorporate graphene paste and rGO powder nanocomposite shows the best optimum was at 3.0 phr with 24 hours’ sonication.

  14. Rubber gloves biodegradation by a consortium, mixed culture and pure culture isolated from soil samples.

    Science.gov (United States)

    Nawong, Chairat; Umsakul, Kamontam; Sermwittayawong, Natthawan

    2018-02-03

    An increasing production of natural rubber (NR) products has led to major challenges in waste management. In this study, the degradation of rubber latex gloves in a mineral salt medium (MSM) using a bacterial consortium, a mixed culture of the selected bacteria and a pure culture were studied. The highest 18% weight loss of the rubber gloves were detected after incubated with the mixed culture. The increased viable cell counts over incubation time indicated that cells used rubber gloves as sole carbon source leading to the degradation of the polymer. The growth behavior of NR-degrading bacteria on the latex gloves surface was investigated using the scanning electron microscope (SEM). The occurrence of the aldehyde groups in the degradation products was observed by Fourier Transform Infrared Spectroscopy analysis. Rhodococcus pyridinivorans strain F5 gave the highest weight loss of rubber gloves among the isolated strain and posses latex clearing protein encoded by lcp gene. The mixed culture of the selected strains showed the potential in degrading rubber within 30 days and is considered to be used efficiently for rubber product degradation. This is the first report to demonstrate a strong ability to degrade rubber by Rhodococcus pyridinivorans. Copyright © 2018. Published by Elsevier Editora Ltda.

  15. Silencing the lettuce homologs of small rubber particle protein does not influence natural rubber biosynthesis in lettuce (Lactuca sativa).

    Science.gov (United States)

    Chakrabarty, Romit; Qu, Yang; Ro, Dae-Kyun

    2015-05-01

    Natural rubber, cis-1,4-polyisoprene, is an important raw material in chemical industries, but its biosynthetic mechanism remains elusive. Natural rubber is known to be synthesized in rubber particles suspended in laticifer cells in the Brazilian rubber tree (Hevea brasiliensis). In the rubber tree, rubber elongation factor (REF) and its homolog, small rubber particle protein (SRPP), were found to be the most abundant proteins in rubber particles, and they have been implicated in natural rubber biosynthesis. As lettuce (Lactuca sativa) can synthesize natural rubber, we utilized this annual, transformable plant to examine in planta roles of the lettuce REF/SRPP homologs by RNA interference. Among eight lettuce REF/SRPP homologs identified, transcripts of two genes (LsSRPP4 and LsSRPP8) accounted for more than 90% of total transcripts of REF/SRPP homologs in lettuce latex. LsSRPP4 displays a typical primary protein sequence as other REF/SRPP, while LsSRPP8 is twice as long as LsSRPP4. These two major LsSRPP transcripts were individually and simultaneously silenced by RNA interference, and relative abundance, polymer molecular weight, and polydispersity of natural rubber were analyzed from the LsSRPP4- and LsSRPP8-silenced transgenic lettuce. Despite previous data suggesting the implications of REF/SRPP in natural rubber biosynthesis, qualitative and quantitative alterations of natural rubber could not be observed in transgenic lettuce lines. It is concluded that lettuce REF/SRPP homologs are not critically important proteins in natural rubber biosynthesis in lettuce. Copyright © 2014 Elsevier Ltd. All rights reserved.

  16. Latex allergy and filaggrin null mutations

    DEFF Research Database (Denmark)

    Carlsen, Berit C; Meldgaard, Michael; Hamann, Dathan

    2011-01-01

    to aeroallergens and it is possible that filaggrin null mutations also increase the risk of latex allergy. The aim of this paper was to examine the association between filaggrin null mutations and type I latex allergy. Methods Twenty latex allergic and 24 non-latex allergic dentists and dental assistants...... in the cases in this study may not have occurred through direct skin contact but through the respiratory organs via latex proteins that are absorbed in glove powder and aerosolized...

  17. Synthesis and characterization of fluorinated polyacrylate latex emulsified with novel surfactants.

    Science.gov (United States)

    Zhang, Cuifeng; Xu, Tingting; Bao, Zhongbin; Chen, Lijun

    2017-01-01

    The fluorinated polyacrylate latex were successfully prepared with semi- continuous seeded emulsion polymerization of butyl acrylate (BA), methyl methacrylate (MMA) and hexafluorobutyl methacrylate (HFMA) which was initiated with potassium persulfate (KPS) initiator and emulsified with the novel mixed surfactants of sodium lauryl glutamate (SLG) and alkylphenol ethoxylates (OP-10). The structure of the resultant latex was confirmed by Fourier transform infrared spectroscopy (FTIR). The particle size of the latex was measured by Zetatrac dynamic light scattering detector. The film of latex was tested by differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and contact angle (CA). The optimum conditions of preparing the novel fluorinated polyacrylate latex are optimized and the results are as follows: the amount of emulsifiers is 4.0%; mass ratio of SLG to OP-10 is 1:1, the amount of the initiator is 0.6%. The mass ratio of MMA to BA is 1:1 and the amount of HFMA is 7.0%. In this case, the conversion is high and the polymerization stability is good. In addition, the water resistance and thermal properties of the latex films were improved significantly in comparison with the film of the latex prepared without the fluorinated monomer.

  18. Latex allergies - for hospital patients

    Science.gov (United States)

    ... ency/patientinstructions/000499.htm Latex allergies - for hospital patients To use the sharing features on this page, ... ADAM Health Solutions. About MedlinePlus Site Map FAQs Customer Support Get email updates Subscribe to RSS Follow ...

  19. Alergia látex-fruta Latex-fruit allergy

    Directory of Open Access Journals (Sweden)

    Flávia Andréia MARIN

    2002-01-01

    Full Text Available O látex está sendo considerado o alergênico do ano 2000, tendo em vista que inúmeros indivíduos, principalmente profissionais da área de saúde e pacientes submetidos a várias intervenções diagnósticas e terapêuticas, estão freqüentemente expostos aos alérgenos do látex, presentes em produtos de borracha natural. As manifestações clínicas conseqüentes às reações alérgicas de hipersensibilidade imediata vão desde rinite, urticária, conjuntivite, angioedema, asma, até anafilaxia. Estudos recentes estão demonstrando que pacientes alérgicos ao látex desenvolvem concomitantemente sensibilização a certos alimentos de origem vegetal, especialmente frutas como papaia, figo, banana, abacate, kiwi, pêssego, abacaxi, melão e castanha, acreditando-se numa provável ocorrência de reações cruzadas entre os alérgenos do látex e destas frutas. Faz-se, então, uma revisão sobre a alergia ao látex, em particular sobre os grupos de risco, incluindo a presença de reatividade cruzada entre o látex e as frutas.The latex is being considered the allergenic agent of the year 2000, taking into account that several individuals, mainly health care professionals, and patients who had undergone many diagnostic and therapeutic interventions, are frequently exposed to latex allergens, which are present in natural rubber latex products. The clinical manifestations, derived from allergic reactions of immediate hypersensitivity vary from since rhinitis, conjunctivitis, urticaria, angioedema, asthma, to anaphylaxis. Recent researches are demonstrating that patients allergic to latex develop concomitantly sensitization to certain vegetable foods, especially fruits like papaya, fig, banana, avocado, kiwi, peach, pineapple, melon and chestnut, and a probable occurrence of cross reaction between allergens of latex and of these fruits is believed. A review is made about latex allergy, in particular about risk groups, including the presence of

  20. Enzymic and structural studies on processed proteins from the vacuolar (lutoid-body) fraction of latex of Hevea brasiliensis

    NARCIS (Netherlands)

    Subroto, T; de Vries, H; Schuringa, JJ; Soedjanaatmadja, UMS; Hofsteenge, J; Jekel, PA; Beintema, JJ

    2001-01-01

    The lutoid-body (bottom) fraction of latex from the rubber tree (Hevea brasiliensis) contains a limited number of major proteins. These are the chitin-binding protein hevein, its precursor and C-terminal fragment of the precursor, a basic chitinase/lysozyme, and a beta-1,3-glucanase. The content and

  1. Processing cost of RVNRL (Radiation Vulcanised Natural Rubber Latex)

    International Nuclear Information System (INIS)

    Wan Manshol Wan Zin; Meor Yahya Razali; Norjanah Mohd

    1996-01-01

    The main components contributing to the cost of building a pilot plant for RVNRL are highlighted. The fixed cost and operating cost of a pilot plant were determined and the production capacity and the cost to prepare I kg of RVNRL were calculated. Two sets of calculations were presented. A set was based on a pilot plant installed with cobalt-60 source of 150 kCi and another set was based on a plant installed with cobalt-60 source of I MCi. The effect of different power utilisation efficiencies and the effect of different vulcanization doses on the production capacities are presented.In general, a small difference in the vulcanization dose and power utilisation efficiency result in a significant change in the production capacity and the cost for RVNRL preparation. Depending on the production capacity, the cost for preparing RVNRL of 50% total solid content can be as low as RM 0.242 per kilograms

  2. Vulcanization of polybutadiene latex induced by 60Co γ-rays irradiation

    International Nuclear Information System (INIS)

    Liu Yuguang; Huang Yudong; Hou Jing; Gao Deyu; Zhang Xuequan

    2007-01-01

    Fully vulcanized polybutadiene rubber particles (FVBR) were prepared by polybutadiene latex (PBL) vulcanization induced by 60 Co γ-rays irradiation, and the effect of absorbed dose on crosslinking behavior was studied. Mean diameter, diameter distribution and morphology of the particles in the PBL irradiated at different doses as well as in the FVBR were characterized by laser particle analyzer and AFM. The crosslinking effect on the mechanical properties of the films, by casting from PBL at different doses correspondingly, was evaluated by mechanical and dynamic mechanical analysis (DMA) respectively. The results showed that the diameter and swelling property decreased with absorbed dose, while crosslink density and gel fraction increased. Moreover, the decrease of the tensile strength and elongation at break, the increase of the hardness in shore A and young's modulus (E), and the increase of storage modulus (E') and narrowing of loss tangent peak (Tan 8) were all accounted for the increment of crosslinking. The Charlesby-Pinner equation fits well with the PBL vulcanization in the range of absorbed doses from 0 to 200kGy. (authors)

  3. Study on grafting of different types of acrylic monomers onto natural rubber by γ-rays

    International Nuclear Information System (INIS)

    Dafader, N.C.; Haque, M.E.; Akhtar, F.; Ahmad, M.U.

    2006-01-01

    A comparative study of various acrylic monomers for grafting onto natural rubber was done. The stability of natural rubber latex (NRL) against coagulum with monomer, mechanical properties of grafted rubbers and percent of grafting were investigated. The NRL with monomers, methylacrylate (MA), ethylacrylate (EA) and n-butylacrylate (n-BA), is unstable but it is stable with methyl methacrylate (MMA), n-butyl methacrylate (BMA) and cyclohexyl methacrylate (CHMA). The mechanical properties and degree of grafting attained a maximum at a total radiation dose of 4 kGy. The values of tensile properties of MMA and CHMA grafted rubbers are almost similar, and higher than those of BMA grafted rubbers. On the other hand, the degree of grafting for CHMA is higher than those of MMA and BMA grafted rubbers. The infrared (IR) spectra of monomer grafted natural rubber were also studied

  4. Synthesis and Characterization of Core-Shell Acrylate Based Latex and Study of Its Reactive Blends

    Directory of Open Access Journals (Sweden)

    Ying Nie

    2008-03-01

    Full Text Available Techniques in resin blending are simple and efficient method for improving the properties of polymers, and have been used widely in polymer modification field. However, polymer latex blends such as the combination of latexes, especially the latexes with water-soluble polymers, were rarely reported. Here, we report a core-shell composite latex synthesized using methyl methacrylate (MMA, butyl acrylate (BA, 2-ethylhexyl acrylate (EHA and glycidyl methacrylate (GMA as monomers and ammonium persulfate and sodium bisulfite redox system as the initiator. Two stages seeded semi-continuous emulsion polymerization were employed for constructing a core-shell structure with P(MMA-co-BA component as the core and P(EHA-co-GMA component as the shell. Results of Transmission Electron Microscopy (TEM and Dynamics Light Scattering (DLS tests confirmed that the particles obtained are indeed possessing a desired core-shell structural character. Stable reactive latex blends were prepared by adding the latex with waterborne melamine-formaldehyde resin (MF or urea-formaldehyde resin (UF. It was found that the glass transition temperature, the mechanical strength and the hygroscopic property of films cast from the latex blends present marked enhancements under higher thermal treatment temperature. It was revealed that the physical properties of chemically reactive latexes with core-shell structure could be altered via the change of crosslinking density both from the addition of crosslinkers and the thermal treatment.

  5. The use of gamma irradiation in preparation of polybutadiene rubber nanopowder; Its effect on particle size, morphology and crosslink structure of the powder

    Energy Technology Data Exchange (ETDEWEB)

    Rezaei Abadchi, Majid; Jalali-Arani, Azam, E-mail: ajalali@aut.ac.ir

    2014-02-01

    Highlights: • Vulcanized rubber powders were prepared by spray drying of irradiated rubber latexes. • Influence of absorbed dose on powder structure and characteristics was investigated. • The size of rubber latex particles did not changed by irradiation. • Crosslink density increased by increasing dose and 98% gel was obtained at 150 kGy. • T{sub g} of rubber powder increased with increasing the irradiation dose. -- Abstract: The aim of this work was the preparation and characterization of polybutadiene rubber (BR) powder by irradiating of rubber lattices using {sup 60}Co radiation and spray-drying of them at the appropriate condition. The influences of absorbed dose on the volume swelling ratio, molecular weight between crosslinks, gel fraction, and glass transition temperature of obtained powder were studied. Morphology, size and size distribution of rubber particles were examined by using scanning electron microscopy (SEM) and laser particle size analyzer (LPSA) technique, respectively. Results obtained by LPSA revealed that radiation has no effect on particle size of rubber latex but after drying, adherence properties of rubber particle causes increase in particle size of rubber powder, as shown in SEM photograph. Fourier transform infrared spectroscopy of rubber powders confirmed that with increasing the irradiation dose, characteristic peak corresponds to the >C=C< double bands decreased. Also Charlesby–Pinner equation was used to evaluate radiation yield.

  6. The use of gamma irradiation in preparation of polybutadiene rubber nanopowder; Its effect on particle size, morphology and crosslink structure of the powder

    International Nuclear Information System (INIS)

    Rezaei Abadchi, Majid; Jalali-Arani, Azam

    2014-01-01

    Highlights: • Vulcanized rubber powders were prepared by spray drying of irradiated rubber latexes. • Influence of absorbed dose on powder structure and characteristics was investigated. • The size of rubber latex particles did not changed by irradiation. • Crosslink density increased by increasing dose and 98% gel was obtained at 150 kGy. • T g of rubber powder increased with increasing the irradiation dose. -- Abstract: The aim of this work was the preparation and characterization of polybutadiene rubber (BR) powder by irradiating of rubber lattices using 60 Co radiation and spray-drying of them at the appropriate condition. The influences of absorbed dose on the volume swelling ratio, molecular weight between crosslinks, gel fraction, and glass transition temperature of obtained powder were studied. Morphology, size and size distribution of rubber particles were examined by using scanning electron microscopy (SEM) and laser particle size analyzer (LPSA) technique, respectively. Results obtained by LPSA revealed that radiation has no effect on particle size of rubber latex but after drying, adherence properties of rubber particle causes increase in particle size of rubber powder, as shown in SEM photograph. Fourier transform infrared spectroscopy of rubber powders confirmed that with increasing the irradiation dose, characteristic peak corresponds to the >C=C< double bands decreased. Also Charlesby–Pinner equation was used to evaluate radiation yield

  7. High Performance Graphene Oxide Based Rubber Composites

    Science.gov (United States)

    Mao, Yingyan; Wen, Shipeng; Chen, Yulong; Zhang, Fazhong; Panine, Pierre; Chan, Tung W.; Zhang, Liqun; Liang, Yongri; Liu, Li

    2013-01-01

    In this paper, graphene oxide/styrene-butadiene rubber (GO/SBR) composites with complete exfoliation of GO sheets were prepared by aqueous-phase mixing of GO colloid with SBR latex and a small loading of butadiene-styrene-vinyl-pyridine rubber (VPR) latex, followed by their co-coagulation. During co-coagulation, VPR not only plays a key role in the prevention of aggregation of GO sheets but also acts as an interface-bridge between GO and SBR. The results demonstrated that the mechanical properties of the GO/SBR composite with 2.0 vol.% GO is comparable with those of the SBR composite reinforced with 13.1 vol.% of carbon black (CB), with a low mass density and a good gas barrier ability to boot. The present work also showed that GO-silica/SBR composite exhibited outstanding wear resistance and low-rolling resistance which make GO-silica/SBR very competitive for the green tire application, opening up enormous opportunities to prepare high performance rubber composites for future engineering applications. PMID:23974435

  8. Observações sôbre a produtividade de seringueiras (Hevea brasiliensis muell.-arg. plantadas de sementes: II - Produtividade de 100 plantas do seringal mirim, em Manaus Observations on the latex production of seedlings of rubber trees (Hevea brasiliensis muell.-arg.: II - Study of 100 rubber trees of the seringal mirim, Manaus

    Directory of Open Access Journals (Sweden)

    Luiz O. T. Mendes

    1960-01-01

    Full Text Available No presente trabalho é feito um estudo da produtividade de 100 seringueiras plantadas de sementes, existentes no Seringal Mirim, em Manaus, Estado do Amazonas, quando tinham a idade de 30 anos. Os resultados se referem à produção obtida de sangrias feitas a meia espiral, em dois regimes de trabalho: a sangria todos os dias (de maio a julho de 1943; b sangria em dias alternados (de agôsto a dezembro de 1943. Tais resultados mostram que, no conjunto de plantas estudado, as de maior produção logo se sobressairam das demais, em qualquer dos regimes de sangria a que foram submetidas; mostram também que, de um modo geral, a mudança do regime de sangria todos os dias para o de sangria em dias alternados provocou um aumento na produção individual, por sangria, tanto mais pronunciado quanto menor foi a produtividade da planta no regime de sangria diária. É também apresentado o resultado do estudo da distribuição, dentro da população, das plantas e conjuntos de plantas classificadas de acordo com sua produtividade, por onde se verifica que umo quarta parte da população foi responsável pela produção de quase 60% do látex total colhido em qualquer dos regimes de sangria adotados. Êsses resultados mostram a possibilidade da formação de seringais de produção relativamente boa, a partir de sementes não selecionadas, desde que plantados inicialmente com densidades bastante elevadas, que permitam posteriores desbastes para a eliminação da maior parte da população, representada pelas plantas de baixa produção.The results of eight month tappings (half-spiral cut of 100 seedlings of rubber trees, 30 years old, are presented. From May to July 1943 the trees were tapped every day; from August to December, every other day. The change of the tapping system, from daily to every other day, caused an increase in the individual yield, per tapping; this yield increase was more pronounced in the low production plants. The study of the

  9. Rubber compounding and processing

    CSIR Research Space (South Africa)

    John, MJ

    2014-06-01

    Full Text Available This chapter presents an overview on the compounding and processing techniques of natural rubber compounds. The introductory portion deals with different types of rubbers and principles of rubber compounding. The primary and secondary fillers used...

  10. The effect of emulsifier on the stability of irradiated LA-TZ latex

    International Nuclear Information System (INIS)

    Made Sumarti K; Utama, Marga; Puspitasari, Tita

    1998-01-01

    The effect of six kinds of stabilizer on the stability of the concentrated LA-TZ latex which contains n-BA have been studied. The six stabilizers are: 1. Naphthalene sulfonic acid formaldehyde condensate, 2. Sodium dialkyl sulfosuccinate, 3. Triethanol amine lauryl sulfate, 4. Sodium polyoxyethylene alkyl phenol ether sulfate, 5. Dodecyl benzene sulfonic acid (Neopelex FS), and 6. Ammonium laurat. The concentrations of the stabilizers are in the range of 0,1 to 0,3% and of the n-BA is 5phr (per hundred rubber). The field natural rubber latex was stabilized by Tetramethyl tiuram disulfide - Zine oxide (TMTD-ZnO) and ammonium gas, and was concentrated by centrifuge. The obtain concentrated LA-TZ latex was added by the n-BA and was kept with various storage time i.e. o, 2, 4, 6, 18, and 24 hours. It was found that the stable latex was irradiated by 15 kGy dose and the physical properties was tested, then the maximum tensile strength of 223,3 kg/cm 2 was found on Neopelex FS concentrate at 0,1%. (authors)

  11. Encapsulation of Clay Platelets inside Latex Particles

    NARCIS (Netherlands)

    Voorn, D.J.; Ming, W.; Herk, van A.M.; Fernando, R.H.; Sung, Li-Piin

    2009-01-01

    We present our recent attempts in encapsulating clay platelets inside latex particles by emulsion polymerization. Face modification of clay platelets by cationic exchange has been shown to be insufficient for clay encapsulation, leading to armored latex particles. Successful encapsulation of

  12. Study on cord/rubber interface at elevated temperatures by H-pull test method

    Science.gov (United States)

    Jamshidi, M.; Afshar, F.; Mohammadi, N.; Pourmahdian, S.

    2005-08-01

    Cords are used as reinforcing materials in rubber compounds. To increase cord/rubber interfacial adhesion, they are coated by an adhesive (usually based on resorcinol-formaldehyde-latex). These composites are used in many sectors such as tire and belt industries. Cord/rubber adhesion strength is an important aspect to determine the durability of system. Due to temperature increase during running tires, the adhesion energy becomes different from initial one. To study cord/rubber interface at elevated temperatures, H-adhesion test method was used. H-pull test is a simple method for adhesion evaluation at ambient temperature, so it is usually used for material quality control. In this research, cord/rubber systems were vulcanized at different temperatures and H-adhesion of samples were evaluated at elevated temperatures. Also cord/rubber interface was studied by ATR analyze to determine interfacial interactions kind.

  13. Managing latex allergies at home

    Science.gov (United States)

    ... Associate Clinical Professor of Medicine, Division of Allergy, Immunology, and Rheumatology, Georgetown University Medical School, Washington, DC. Also reviewed by David Zieve, MD, MHA, Isla Ogilvie, PhD, and the A.D.A.M. Related MedlinePlus Health Topics Latex Allergy Browse the Encyclopedia A.D.A. ...

  14. Characterization of the natural rubber from new rubber tree clones of PB 300 series

    International Nuclear Information System (INIS)

    Silva, Maycon J.; Spinelli, Rafaela O.; Moreno, Rogerio M.B.; Mattoso, Luiz H.C.; Martins, Maria Alice; Scaloppi Junior, Erivaldo J.

    2015-01-01

    The natural rubber (NR) is present in more than 2500 species of plants, being the Hevea brasiliensis the most commercially exploited. It is a raw material of great importance to the Brazilian economy, but the country faces a production's deficit, having to import about 60% of its consumption. In this work , the latex obtained from rubber tree of new clones of PB series 300 (PB 311, PB 312, PB 314 , PB 326, PB 346 and PB 350 ) and RRIM 600 (control) were characterized by dry rubber content (DRC), total solids content, distribution of particle size, Zeta potential, thermogravimetry, differential scanning calorimetry, infrared in the spectroscopy (FTIR), nuclear magnetic resonance (NMR) and technological properties. The DRC values ranged from 33% to 40%, and total solids of 38% to 44%. All of the clones showed average particle diameter between 180.0 to 192.1 nm, excluding clones PB 326 and PB 346 with 150.0 nm and 157.9 nm, respectively. The NMR spectra and FTIR showed that the structure of the natural rubber from all clones studied is cis -1,4- polyisoprene. Natural rubber from the new clones showed good thermal stability up to 285 °C and glass transition temperature of -64 °C. (author)

  15. The Effect of Gamma Irradiation on the Mechanical Properties of vulcanized Natural Rubber and Natural Rubber-Polyethylene Blends

    International Nuclear Information System (INIS)

    Sudradjat Iskandar

    2008-01-01

    To enhance the quality of vulcanized natural rubber and natural rubber-polyethylene blends, gamma irradiation has been done. The compound of natural rubber and natural rubber-polyethylene blends made by using roll mill machine. The mixed materials were antioxidant, anti ozon, plasticizer and vulcanisator. The natural rubber and natural rubber-polyethylene blends compound were vulcanizer and made a slab (film of sample) using hot and could press machine. The slabs produced were then gamma irradiated at irradiation dose of 75, 150 and 300 kGy. Before and after irradiation, the slab were characterized using strograph R1 machine. The results showed that the modulus 300 and hardness of vulcanized natural rubber and natural rubber-polyethylene blends were increasing; the tensile strength and tear strength were increasing to maximum level then decreasing with gamma irradiation, while the elongation at break was decreasing. The maximum tensile strength of vulcanized natural rubber and natural rubber-polyethylene blends were found at irradiation dose of 75 kGy. At the irradiation dose of 75 kGy, the tensile strength of vulcanized natural rubber increased from 17.6 MN/m 2 to 21.2 MN/m 2 , while the tensile strength of vulcanized natural rubber-polyethylene blends increased slightly from 18.7 MN/m 2 to 19.4 MN/m 2 . (author)

  16. Prevalence of IgE antibodies to an extract from rubber tree (Hevea brasiliensis latex and recombinant pollen allergens (Phl P 1, Phl P 2, Phl P 5, Bet v 1 and Bet v 2 in the sera of Italian atopic patients

    Directory of Open Access Journals (Sweden)

    Renato E. Rossi

    2001-01-01

    Conclusions: The findings of the present study may support the concept that a high proportion of sera containing IgE to rBet v 2, rPhl p 1 and rPhl p 5 simultaneously contain antilatex IgE. Therefore, patients with specific IgE to these recombinant allergens with no history of current latex exposure may need additional evaluation.

  17. Whole-transcriptome survey of the putative ATP-binding cassette (ABC) transporter family genes in the latex-producing laticifers of Hevea brasiliensis.

    Science.gov (United States)

    Zhiyi, Nie; Guijuan, Kang; Yu, Li; Longjun, Dai; Rizhong, Zeng

    2015-01-01

    The ATP-binding cassette (ABC) proteins or transporters constitute a large protein family in plants and are involved in many different cellular functions and processes, including solute transportation, channel regulation and molecular switches, etc. Through transcriptome sequencing, a transcriptome-wide survey and expression analysis of the ABC protein genes were carried out using the laticiferous latex from Hevea brasiliensis (rubber tree). A total of 46 putative ABC family proteins were identified in the H. brasiliensis latex. These consisted of 12 'full-size', 21 'half-size' and 13 other putative ABC proteins, and all of them showed strong conservation with their Arabidopsis thaliana counterparts. This study indicated that all eight plant ABC protein paralog subfamilies were identified in the H. brasiliensis latex, of which ABCB, ABCG and ABCI were the most abundant. Real-time quantitative reverse transcription-polymerase chain reaction assays demonstrated that gene expression of several latex ABC proteins was regulated by ethylene, jasmonic acid or bark tapping (a wound stress) stimulation, and that HbABCB15, HbABCB19, HbABCD1 and HbABCG21 responded most significantly of all to the abiotic stresses. The identification and expression analysis of the latex ABC family proteins could facilitate further investigation into their physiological involvement in latex metabolism and rubber biosynthesis by H. brasiliensis.

  18. Styrene grafted natural rubber reinforced by in situ silica generated via sol–gel technique

    Energy Technology Data Exchange (ETDEWEB)

    Sittiphan, Torpong [Program of Petrochemistry and Polymer Sciences, Faculty of Science, Chulalongkorn University, Bangkok 10330 (Thailand); Prasassarakich, Pattarapan [Department of Chemical Technology, Faculty of Science, Chulalongkorn University, Bangkok 10330 (Thailand); Poompradub, Sirilux, E-mail: sirilux.p@chula.ac.th [Department of Chemical Technology, Faculty of Science, Chulalongkorn University, Bangkok 10330 (Thailand)

    2014-02-15

    Highlights: • Sol–gel reaction by NR latex was the absence of use of organic solvent and base catalyst. • Well dispersed in situ formed silica particles in the rubber matrix were obtained. • In situ silica was better to improve mechanical properties of rubber vulcanizates. -- Abstract: The filling of styrene graft natural rubber (ST-GNR) with in situ formed silica was performed using the sol–gel reaction via the latex solution method. The mechanical properties of ST-GNR/NR vulcanizate were improved when using the in situ formed silica to levels higher than those obtained with the commercial ex situ formed silica filled ST-GNR/NR vulcanizates at a comparable silica content of 12 parts by weight per hundred parts of rubber. Transmission electron microscopy analysis revealed that the in situ silica particles were small (∼40 nm diameter) and well dispersed, while the commercial silica particles were larger (∼60 nm diameter) and markedly agglomerated in the rubbery matrix. The mechanical properties of the composites prepared via both the solid rubber and latex solution methods were comparable.

  19. Responses of rubber leaf phenology to climatic variations in Southwest China

    Science.gov (United States)

    Zhai, De-Li; Yu, Haiying; Chen, Si-Chong; Ranjitkar, Sailesh; Xu, Jianchu

    2017-11-01

    The phenology of rubber trees (Hevea brasiliensis) could be influenced by meteorological factors and exhibits significant changes under different geoclimates. In the sub-optimal environment in Xishuangbanna, rubber trees undergo lengthy periods of defoliation and refoliation. The timing of refoliation from budburst to leaf aging could be affected by powdery mildew disease (Oidium heveae), which negatively impacts seed and latex production. Rubber trees are most susceptible to powdery mildew disease at the copper and leaf changing stages. Understanding and predicting leaf phenology of rubber trees are helpful to develop effective means of controlling the disease. This research investigated the effect of several meteorological factors on different leaf phenological stages in a sub-optimal environment for rubber cultivation in Jinghong, Yunnan in Southwest China. Partial least square regression was used to quantify the relationship between meteorological factors and recorded rubber phenologies from 2003 to 2011. Minimum temperature in December was found to be the critical factor for the leaf phenology development of rubber trees. Comparing the delayed effects of minimum temperature, the maximum temperature, diurnal temperature range, and sunshine hours were found to advancing leaf phenologies. A comparatively lower minimum temperature in December would facilitate the advancing of leaf phenologies of rubber trees. Higher levels of precipitation in February delayed the light green and the entire process of leaf aging. Delayed leaf phenology was found to be related to severe rubber powdery mildew disease. These results were used to build predictive models that could be applied to early warning systems of rubber powdery mildew disease.

  20. Draft genome sequence of the rubber tree Hevea brasiliensis

    Directory of Open Access Journals (Sweden)

    Rahman Ahmad Yamin Abdul

    2013-02-01

    Full Text Available Abstract Background Hevea brasiliensis, a member of the Euphorbiaceae family, is the major commercial source of natural rubber (NR. NR is a latex polymer with high elasticity, flexibility, and resilience that has played a critical role in the world economy since 1876. Results Here, we report the draft genome sequence of H. brasiliensis. The assembly spans ~1.1 Gb of the estimated 2.15 Gb haploid genome. Overall, ~78% of the genome was identified as repetitive DNA. Gene prediction shows 68,955 gene models, of which 12.7% are unique to Hevea. Most of the key genes associated with rubber biosynthesis, rubberwood formation, disease resistance, and allergenicity have been identified. Conclusions The knowledge gained from this genome sequence will aid in the future development of high-yielding clones to keep up with the ever increasing need for natural rubber.

  1. Rubber glove wearing device

    International Nuclear Information System (INIS)

    Nozaki, Tatsuo; Takada, Kaoru.

    1994-01-01

    Rubber groves are attached each to an upper end of a glove putting vessel having an air-sucking hole on the bottom by enlarging an opening end of the rubber glove and turning back the inside to the outside. When the sucking device is operated, air in the glove putting device is sucked and the rubber glove is expanded by an atmospheric pressure. After expansion of the rubber glove to some extent, the sucking device is stopped, and presence or absence of failures of the rubber glove is confirmed by shrinkage of the rubber glove and by an indication value of a pressure gauge for detecting the pressure change in the vessel. Then, a hand is inserted to the expanded rubber glove, and a detaching switch in the vessel is pushed by a finger tip. A detaching piece at the upper end of the vessel is protruded outwardly to enlarge the turned-back portion of the rubber glove to easily release the rubber glove from the putting vessel, and the rubber glove is put on. This enables to wear the rubber glove and conduct failure test simultaneously. Further, a user can put on the rubber glove without touching the outside of the rubber glove. (I.N.)

  2. Enhanced protein adsorption and patterning on nanostructured latex-coated paper.

    Science.gov (United States)

    Juvonen, Helka; Määttänen, Anni; Ihalainen, Petri; Viitala, Tapani; Sarfraz, Jawad; Peltonen, Jouko

    2014-06-01

    Specific interactions of extracellular matrix proteins with cells and their adhesion to the substrate are important for cell growth. A nanopatterned latex-coated paper substrate previously shown to be an excellent substrate for cell adhesion and 2D growth was studied for directed immobilization of proteins. The nanostructured latex surface was formed by short-wavelength IR irradiation of a two-component latex coating consisting of a hydrophilic film-forming styrene butadiene acrylonitrile copolymer and hydrophobic polystyrene particles. The hydrophobic regions of the IR-treated latex coating showed strong adhesion of bovine serum albumin (cell repelling protein), fibronectin (cell adhesive protein) and streptavidin. Opposite to the IR-treated surface, fibronectin and streptavidin had a poor affinity toward the untreated pristine latex coating. Detailed characterization of the physicochemical surface properties of the latex-coated substrates revealed that the observed differences in protein affinity were mainly due to the presence or absence of the protein repelling polar and charged surface groups. The protein adsorption was assisted by hydrophobic (dehydration) interactions. Copyright © 2014 Elsevier B.V. All rights reserved.

  3. Natural rubber: leather composites

    OpenAIRE

    Ravichandran,K.; Natchimuthu,N.

    2005-01-01

    Leather is a fibrous protein consisting of collagen in a three dimensionally crosslinked network. Chrome tanning of leather improves the appearance of leather but at the same time emits both solid and liquid chrome leather wastes. Scrap rubber recycling using untreated and neutralized leather fibrous particles in natural rubber has been studied. Vulcanization, mechanical, morphological and swelling properties of the natural rubber - scrap rubber composites containing neutralized leather have ...

  4. Latex sensitisation in healthcare workers in Singapore.

    Science.gov (United States)

    Tang, M B Y; Leow, Y H; Ng, V; Koh, D; Goh, C L

    2005-06-01

    Epidemiological data on latex sensitisation among Asian healthcare workers is lacking. The aim of the study is to determine the rate of latex sensitisation in our healthcare workers. We recruited 313 healthcare workers, of which 46.6% were operating theatre staff and 53.4% were non-operating theatre staff. Seventy-one administrative staff served as controls. All participants answered a self-administered questionnaire relating to latex exposure and glove-related symptoms. Latex sensitisation was determined by skin prick testing to latex and latex-specific IgE detection. The prevalence of latex sensitisation among healthcare workers was 9.6%, with no difference between operating theatre and nonoperating theatre staff. Glove-related symptoms were reported in 13.7% of all healthcare workers, of which 22.9% were sensitised to latex. Only 26.7% of latex-sensitised healthcare workers had glove-related symptoms while the rest were asymptomatic. The most common symptoms were itch and hand eczema but the most important discriminating symptom was contact urticaria. Personal history of atopy was more common in sensitised healthcare workers (40.0%) compared to non-sensitised workers (31.8%). Only 1 out of 9 (11.2%) symptomatic latex-sensitised subjects had sought previous medical attention for the problem. Latex sensitisation among healthcare workers in Singapore should be considered a significant occupational health risk, as it is in the West. Increased screening and awareness of this problem is essential to identify those at risk.

  5. Latex allergy: assessment of knowledge, appropriate use of gloves and prevention practice among hospital healthcare workers.

    Science.gov (United States)

    Al-Niaimi, F; Chiang, Y Z; Chiang, Y N; Williams, J

    2013-01-01

    Healthcare workers and patients are often exposed to natural rubber latex (NRL) through contact with gloves and various healthcare products, which can potentially cause allergic reactions, with varying degrees of severity. In 2008, the Royal College of Physicians published their first evidence-based guidance on occupational health interventions for latex allergy, which emphasized the importance of healthcare workers having knowledge of latex allergy. This study aimed to survey the knowledge of healthcare workers (n = 156) about latex gloves and NRL allergy, routine prevention practice and the appropriate use of gloves in patient care. Healthcare workers in a large teaching hospital were surveyed using a standard questionnaire. We found that only 1% of healthcare workers were able to correctly match the appropriate gloves to the specifically designed procedure. More than half (n = 74.53%) were unable to recognize the presentation of type 1 allergy to NRL. Of the 156 participants, 131 (84%) considered that they would benefit from training about NRL allergy and the use of different types of gloves in clinical care. This survey indicates the importance of education regarding appropriate use of gloves and prevention of NRL allergy among healthcare workers, and dermatologists should play an important role in facilitating this. © The Author(s). CED © 2012 British Association of Dermatologists.

  6. Decontamination of latex gloves; Decontamination de gants en latex

    Energy Technology Data Exchange (ETDEWEB)

    Boutot, P; Schipfer, P; Blachere, A [Commissariat a l' Energie Atomique, Chusclan (France). Centre de Production de Plutonium de Marcoule

    1969-07-01

    Initially the latex gloves used in controlled zones were processed after use as radioactive waste. In view of the continually increasing number used, however, the persons in charge of the SPRAR have considered the possibility of decontaminating the gloves and using them again after control. The recovery installations which have been developed were initially designed rather crudely and operated irregularly; they have been progressively improved as a result of the experience acquired; today they are more really an industrial concern, equipped with automatic machinery. In 1967 it has been possible with this set-up to recover 247000 pairs of gloves, representing nearly 70 per cent of the number treated. (author) [French] Initialement, les gants de latex utilises dans les zones controlees etaient conditionnes apres emploi comme dechets radioactifs. Mais, devant l'augmentation sans cesse croissante des quantites employees, les responsables du SPRAR ont envisage leur decontamination et leur recyclage apres controles. Les installations de recuperation mises au point, de conception artisanale et fonctionnant de maniere episodique au depart, se sont progressivement ameliorees au fur et a mesure de l'experience acquise; elles revetent aujourd'hui le caractere d'une exploitation industrielle equipee de machines automatiques. En 1967, ces nouvelles installations ont permis de recuperer 247000 paires de gants, ce qui represente pres de 70 pour cent des quantites traitees. (auteur)

  7. Metal Rubber Sensor Appliqus for Rotor Blade Air, Phase II

    Data.gov (United States)

    National Aeronautics and Space Administration — Thin film Metal RubberTM sensor appliqués have the potential to reduce the time, complexity and cost of measuring air flow-induced skin friction during the...

  8. EDITORIALS Latex allergy: 'Plight, rights and fights'

    African Journals Online (AJOL)

    anaphylaxis and life-threatening food allergies to cross-reacting fruit allergens such as kiwi, banana, tomato and chestnuts). Latex allergy is also encountered more frequently in children with spina bifida than in other hospitalised children.[7] Sensitisation is usually confirmed by commercial latex allergy skinprick testing or by ...

  9. Jackfruit anaphylaxis in a latex allergic patient.

    Science.gov (United States)

    Wongrakpanich, Supakanya; Klaewsongkram, Jettanong; Chantaphakul, Hiroshi; Ruxrungtham, Kiat

    2015-03-01

    Several fruits have been reported to crossreact with latex antigen in latex allergy patients but little is known regarding tropical fruits in particular. Here we report the case of a 34-year old nurse who developed anaphylaxis following the ingestion of dried jackfruit (Artocarpus heterophyllus). The patient had a history of chronic eczema on both hands resulting from a regular wear of latex gloves. She and her family also had a history of atopy (allergic rhinitis and/or atopic dermatitis). The results of skin prick tests were positive for jackfruit, latex glove, kiwi and papaya, but the test was negative for banana. While we are reporting the first case of jackfruit anaphylaxis, further research needs to be conducted to identify the mechanisms underlying it. In particular, in-vitro studies need to be designed to understand if the anaphylaxis we describe is due to a cross reactivity between latex and jackfruit or a coincidence of allergy to these 2 antigens.

  10. Nitrile versus Latex for Glove Juice Sampling.

    Science.gov (United States)

    Landers, Timothy F; Dent, Anthony

    2014-01-01

    The objective of this study was to explore the utility of nitrile gloves as a replacement for latex surgical gloves in recovering bacteria from the hands. Two types of nitrile gloves were compared to latex gloves using the parallel streak method. Streaks of Klebsiella pneumoniae and Staphylococcus aureus were made on tryptic soy agar plates, and the zones of inhibition were measured around pieces of glove material placed on the plates. Latex gloves produced a mean zone of inhibition of 0.28 mm, compared to 0.002 mm for nitrile gloves (pnitrile may be a viable alternative to latex in glove juice sampling methods, since nitrile avoids the risk of latex exposure.

  11. Nitrile versus Latex for Glove Juice Sampling.

    Directory of Open Access Journals (Sweden)

    Timothy F Landers

    Full Text Available The objective of this study was to explore the utility of nitrile gloves as a replacement for latex surgical gloves in recovering bacteria from the hands. Two types of nitrile gloves were compared to latex gloves using the parallel streak method. Streaks of Klebsiella pneumoniae and Staphylococcus aureus were made on tryptic soy agar plates, and the zones of inhibition were measured around pieces of glove material placed on the plates. Latex gloves produced a mean zone of inhibition of 0.28 mm, compared to 0.002 mm for nitrile gloves (p<.001. While the parallel streak method is not intended as a quantitative estimate of antimicrobial properties, these results suggest that nitrile may be a viable alternative to latex in glove juice sampling methods, since nitrile avoids the risk of latex exposure.

  12. Ultraviolet curing of acrylated liquid natural rubber for surface coating application

    Directory of Open Access Journals (Sweden)

    Kannikar Kwanming

    2009-01-01

    Full Text Available Ultraviolet curable acrylated liquid natural rubber was prepared by grafting of photosensitive molecule onto liquid natural rubber for surface coating application. The liquid natural rubber (LNR was firstly obtained by degradation of natural rubber latex with hydrogen peroxide and cobalt acetylacetonate at 65oC for 72 hrs. The preparation of acrylated natural rubber was carried out by the reaction of acrylic acid and epoxidized liquid natural rubber (ELNR prior obtained from LNR with formic acid and hydrogen peroxide in the ratio of 2:1 by weight in toluene at 80oC for 6, 9, 12, 18, and 24 hrs. It was found that the percentage of acrylate grafted onto liquid natural rubber depended on the reaction time. Surface coating was performed by using acrylated liquid natural rubber and 1,6-hexanediol diacrylate (HDDA or tripropylene glycol diacrylate (TPGDA as a crosslinker and Irgarcure 184 or Irgarcure 651 as a photoinitiator under UV exposure for 30, 60, and 90 seconds. The hardness test of cured products was investigated using the Pencil hardness test at pencil level of 2B to 6H. It was found that the highest hardness of surface coating was at pencil level of 4H for the product using TPGDA and Irgacure 651 in the ratio of 80:10 parts per hundred of rubber (phr. The cured products were able to resist to 2% H2SO4 and distilled water for more than 24 hrs.

  13. USED IN THE MANUFACTURE OF EMULSION RUBBER WASTE OF SUGAR MANUFACTURE – MOLASSES

    Directory of Open Access Journals (Sweden)

    S. S. Nikulin

    2015-01-01

    Full Text Available Currently, much attention is paid to development, allowing use of waste and by-products formed during certain manufacturing processes. This allows you to either reduce or completely eliminate the use of valuable and expensive raw materials. The use of this raw material in the production of synthetic rubber will not only reduce the cost of coagulation and acidifying agents, but also to improve the environmental situation. Featured in some cases effective coalescing agents based on polymeric quaternary ammonium salts (PCHSA have a high coagulating power, and hence low consumption of the allocation of the rubber latex (3-5 kg0t-1 rubber. Scarcity and high cost of these drugs leads to higher prices resulting rubber. Furthermore it is known that the application requires keeping PCHSA sufficiently precise dosage administered substances by the action of a latex, owing to the high capacity of the antiseptic may lead to discharge into natural waters polluted waters. However, using as the coagulating agent departing sugar production molasses solves a number of problematic steps in the production of synthetic rubber. First, a well-studied effective coagulation effect of different nitrogen derivatives relating to cationic surfactants. In freshly prepared solutions of molasses contained about 9 wt%, and this value increases significantly during enzymatic fermentation. Secondly, highly acidic environment of aqueous solutions of molasses after storage can allow their use in addition to or instead of the sulfuric acid used in large amounts (up to 15 kg m-1 rubber technology selection tests carried found that vulcanizates derived from rubber samples isolated molasses, consistent with the requirements and were similar to control samples prepared from the latex using sodium chloride.

  14. Developments in rubber technology 2 synthetic rubbers

    CERN Document Server

    Lee, K

    1981-01-01

    This book is intended for those people who have a knowledge or understanding of rubber materials and processes but who wish to update their knowledge. It should be read in conjunction with Developments in Rubber Technology-l as that volume discussed developments in natural rubber and selected special purpose synthetic rubbers as well as additives. The authors have been selected for their expertise in each particular field and we, as editors, would like to express our appreciation to the individual authors and also to their companies. Such a book would be impossible to produce without such active cooperation as we have received. Volumes 1 and 2 of Developments in Rubber Technology cover rubbers which are processed and vulcanised in the traditional manner. It is appreciated that the omission of non-vulcanised rubber materials (the so­ called thermoplastic elastomers) will be unwelcome to many readers but it is intended, because of the size of the subject, to cover these materials in a subsequent volume. A.W. K...

  15. The use of gamma irradiation in preparation of polybutadiene rubber nanopowder; Its effect on particle size, morphology and crosslink structure of the powder

    Science.gov (United States)

    Rezaei Abadchi, Majid; Jalali-Arani, Azam

    2014-02-01

    The aim of this work was the preparation and characterization of polybutadiene rubber (BR) powder by irradiating of rubber lattices using 60Co radiation and spray-drying of them at the appropriate condition. The influences of absorbed dose on the volume swelling ratio, molecular weight between crosslinks, gel fraction, and glass transition temperature of obtained powder were studied. Morphology, size and size distribution of rubber particles were examined by using scanning electron microscopy (SEM) and laser particle size analyzer (LPSA) technique, respectively. Results obtained by LPSA revealed that radiation has no effect on particle size of rubber latex but after drying, adherence properties of rubber particle causes increase in particle size of rubber powder, as shown in SEM photograph. Fourier transform infrared spectroscopy of rubber powders confirmed that with increasing the irradiation dose, characteristic peak corresponds to the >Cdbnd C< double bands decreased. Also Charlesby-Pinner equation was used to evaluate radiation yield.

  16. Optical and Thermal Stability of Oligofluorene/Rubber Luminescent Blend.

    Science.gov (United States)

    Barbosa, Camila G; Faez, Roselena; Péres, Laura O

    2016-09-01

    This paper proposes to obtain homogeneous and stable blends of oligo(9,9-dioctylfluorene)-co-phenylene (OF), a conjugated oligomer with strong tendency of formation of excimers in the solid state, and nitrile rubber (NBR). This rubber protection reduces the formation of polymer excimers in the films. The fluorene oligomer was synthesized via Suzuki reaction and incorporated in the nitrile rubber. The films were formed by spin coating and casting techniques on the proportions of 1, 5, 10, 20 and 50 % (w/w) of OF in the nitrile rubber (NBR). The structural, optical and thermal properties of the films were evaluated with infrared, UV-Vis, fluorescence and thermogravimetry, respectively. The nitrile rubber proved to be essential for the preparation of homogeneous and stable films, since it was not possible to obtain films with only fluorene using the above-mentioned techniques. Furthermore, luminescent properties of OF are unchanged and the excimers formation in the solid state decrease suggesting the efficiency of nitrile rubber as the matrix for making films.

  17. Reassessment of anoxic storage of ethnographic rubber

    DEFF Research Database (Denmark)

    Shashoua, Yvonne; Dyer, Joanne; Ward, Clare

    2011-01-01

    This paper revisits the 1991–1995 British Museum field trial on anoxic storage, where 23 registered ethnographic rubber objects were enclosed in oxygen barrier film Cryovac BDF200 with sachets of the oxygen absorbent Ageless Z. A unique opportunity for study was presented since most of the enclos...

  18. Unraveling the mystery of natural rubber biosynthesis. Part II. Composition and growth of in vitro natural rubber using high-resolution size exclusion chromatography

    Energy Technology Data Exchange (ETDEWEB)

    Chiang, Cheng Ching K. [Univ. of Akron, OH (United States); Barkakaty, Balaka [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Puskas, Judit E. [Univ. of Akron, OH (United States); Xie, Wenshuang [The Ohio State Univ., Wooster, OH (United States); Cornish, Katrina [The Ohio State Univ., Wooster, OH (United States); Peruch, Federic [Univ. of Bordeaux, Pessac Cedex (France); Deffieux, Alain [Univ. of Bordeaux, Pessac Cedex (France)

    2014-09-01

    The superior properties of natural rubber (cis-1,4-polyisoprene [NR]) are a function of its structure and composition, properties that still remain a mystery and that are irreplaceable by any synthetic rubber. NR from guayule (Parthenium argentatum) has been gaining special interest for its hypoallergenic properties while maintaining superior mechanical properties that are commonly associated with the Brazilian rubber tree (Hevea brasiliensis), the most common source of NR. Techniques exist to isolate washed rubber particles (WRPs) that contain enzymatically active rubber transferase, to study NR biosynthesis, and previous work on the in vitroNRgrowth in Hevea has demonstrated the presence of around 50wt%of a low molecular weight ([MW], Mn <10 000 g/mol) fraction. Structural and compositional analyses of this low MW fraction in Hevea are challenging due to the high protein content. Here, we discuss the analysis and composition of guayule latex and WRPs using high-resolution Size Exclusion Chromatography. We also discuss the composition of the soluble fraction of inactive guayule latex using matrix-assisted laser desorption ionization/time of flight mass spectrometry.

  19. PROBLEMATIC IN THE PROCESSES OF PRODUCTION IN RUBBER PLANTATIONS (Hevea brasiliensis Muell Arg. IN TABASCO, MEXICO

    Directory of Open Access Journals (Sweden)

    Heyra Izquierdo-Bautista

    2011-03-01

    Full Text Available The objective of this study was to identify some of the basic problems presented in the production process in rubber plantations Hevea brasiliensis Muell Arg. in Tabasco, Mexico. The applied diagnosis technique was the randomized survey for 68 producers in plantations under rubber production. ANOVA and Duncan analyses were done (P< 0.05. Plantations under production were between 7 to 46 years old. The 24% of these are considered as young plantations (7 to 18 years old, 34% mature (19 to 30 years old, and 12% old growth (31 to 46 years old, according to the level of latex production. Latex collection is realized by 85% men and 15% women. An important detected problem is the incidence of insects and diseases over the 82% of the plantations. In Tabasco State, two types of raw material are generated: clot (solid and latex (liquid. The tapping systems are ½ S d/1 6d/7 (one cuts in an average spiral with daily tapping over the 49% of the plantations, and the system ½ S d/2 6d/7, cuts in semi-spirals with alternating tapping over 51% of the plantations. The producers that practiced daily tapped obtained yields of 1.588 kg per ha/yr of dry rubber, in the other hand, those that tapped every other day obtained a yield of 1.647 kg per ha/year of dry rubber. The yield in daily tapping was 3.54% lower than the system with alternating tapping. The income obtained by the producers of fresh rubber varied from $8.750, 00 (810, 2 USD ha/year to $27.870, 00 (2.580 USD ha/year in 2006 and the production of latex from $5.955, 00 (551, 4 USD to 16.568,00 (1.534 USD per ha/year.

  20. [Latex allergy in a population at risk].

    Science.gov (United States)

    Ruiz Fernández, M; Flores Sandoval, G; Orea Solano, M

    1999-01-01

    The allergy to latex is an illness whose prevalence has been increased in very significant form in the last years. To know the allergy incidence to latex in population of risk, as well as to identify the related sintomatology and the importance or paper that play the atopia antecedents and time of contact with latex for the development of the illness. We carry out a prospective, descriptive, experimental and traverse study in population of risk, in the service of Allergy and clinical Immunology of the Hospital Regional Lic. Adolfo López Mateos, ISSSTE. One hundred patients of both sexes were included, with age of 20 to 50 years, with the antecedent of being personal medical and paramedic and to have presented contact with latex material in a minimum period of one year. They were carried out clinical history with registration of sintomatology nasal, bronchial, cutaneous and associated to contact with latex. They were carried out cutaneous test for prick to latex with positive control with the help of histamine solution and negative control with solution of Evans and immediate reading of the same one. 22% of the patients in study, they presented positive skin test latex, with a time of exhibition 10 year-old average, 68% presented antecedent of atopy personal, family and, likewise the associate sintomatology was in a 33.3% dermatology, 54.5 nasal, nobody presented bronchial symptoms and a 9% asymptomatic was reported. We support that the immediate skin test latex for Prick is an important parameter of support diagnosis for allergy to type 1 latex.

  1. Nutrient cycling in a RRIM 600 clone rubber plantation

    Directory of Open Access Journals (Sweden)

    Murbach Marcos Roberto

    2003-01-01

    Full Text Available Few reports have been presented on nutrient cycling in rubber tree plantations (Hevea brasiliensis Muell. Arg.. This experiment was carried out to evaluate: the effect of K rates on the amount of nutrients transfered to the soil in a 13-year old Hevea brasilensis RRIM 600 clone plantation, nutrient retranslocation from the leaves before falling to the soil, and nutrient loss by dry rubber export. The experiment started in 1998 and potassium was applied at the rates of 0, 40, 80 and 160 kg ha-1 of K2O under the crowns of 40 rubber trees of each plot. Literfall collectors, five per plot, were randomly distributed within the plots under the trees. The accumulated literfall was collected monthly during one year. The coagulated rubber latex from each plot was weighed, and samples were analyzed for nutrient content. Increasing K fertilization rates also increased the K content in leaf literfall. Calcium and N were the most recycled leaf nutrients to the soil via litterfall. Potassium, followed by P were the nutrients with the highest retranslocation rates. Potassium was the most exported nutrient by the harvested rubber, and this amount was higher than that transfered to the soil by the leaf literfall.

  2. Taxonomic revision and phylogenetic analyses of rubber powdery mildew fungi.

    Science.gov (United States)

    Liyanage, K K; Khan, Sehroon; Brooks, Siraprapa; Mortimer, Peter E; Karunarathna, Samantha C; Xu, Jianchu; Hyde, Kevin D

    2017-04-01

    Powdery mildew is a fungal disease that infects a wide range of plants, including rubber trees, which results in a reduction of latex yields of up to 45%. The causal agent of powdery mildew of rubber was first described as Oidium heveae, but later morpho-molecular research suggested that in the past, O. heveae has been confused with Erysiphe quercicola. However, it is still under debate whether the causal agent should be classified as a species of the genus Erysiphe emend. or Golovinomyces and Podosphaera, respectively. Therefore, the aim of this study was to undertake the morpho-molecular characterization of powdery mildew species associated with rubber trees, thus resolving these taxonomic issues. Morphological observation under light and scanning electron microscopes (SEM) clearly identified two morphotypes of the rubber powdery mildew. With the support of morphological and phylogenetic data, one of the two morphotypes was identified as the asexual morph of E. quercicola, while the second morphotype is still insufficiently known and according to the morphological results obtained we assume that it might belong to the genus Golovinomyces. More collections and additional molecular data are required for final conclusions regarding the exact taxonomic position of the second morphotype of rubber powdery mildew and its relation to the name O. heveae. The haplotype analysis identified eight haplotype groups of E. quercicola indicating the high genetic diversity of the species. Copyright © 2017 Elsevier Ltd. All rights reserved.

  3. Cellulose nanocrystals reinforced foamed nitrile rubber nanocomposites.

    Science.gov (United States)

    Chen, Yukun; Zhang, Yuanbing; Xu, Chuanhui; Cao, Xiaodong

    2015-10-05

    Research on foamed nitrile rubber (NBR)/cellulose nanocrystals (CNs) nanocomposites is rarely found in the literatures. In this paper, CNs suspension and NBR latex was mixed to prepared the foamed NBR/CNs nanocomposites. We found that the CNs mainly located in the cell walls, effectively reinforcing the foamed NBR. The strong interaction between the CNs and NBR matrix restricted the mobility of NBR chains surrounding the CNs, hence increasing the crosslink density of the NBR matrix. CNs exhibited excellent reinforcement on the foamed NBR: a remarkable increase nearly 76% in the tensile strength of the foamed nanocomposites was achieved with a load of only 15 phr CNs. Enhanced mechanical properties make the foamed NBR/CNs nanocomposites a promising damping material for industrial applications with a potential to reduce the petroleum consumption. Copyright © 2015 Elsevier Ltd. All rights reserved.

  4. High throughput deposition of hydrogenated amorphous carbon coatings on rubber with expanding thermal plasma

    NARCIS (Netherlands)

    Pei, Y.T.; Eivani, A.R.; Zaharia, T.; Kazantis, A.V.; Sanden, van de M.C.M.; De Hosson, J.T.M.

    2014-01-01

    Flexible hydrogenated amorphous carbon (a-C:H) thin film coated on rubbers has shown outstanding protection of rubber seals from friction and wear. This work concentrates on the potential advances of expanding thermal plasma (ETP) process for a high throughput deposition of a-C:H thin films in

  5. Natural rubber: leather composites

    Directory of Open Access Journals (Sweden)

    K. Ravichandran

    2005-06-01

    Full Text Available Leather is a fibrous protein consisting of collagen in a three dimensionally crosslinked network. Chrome tanning of leather improves the appearance of leather but at the same time emits both solid and liquid chrome leather wastes. Scrap rubber recycling using untreated and neutralized leather fibrous particles in natural rubber has been studied. Vulcanization, mechanical, morphological and swelling properties of the natural rubber - scrap rubber composites containing neutralized leather have been discussed. Use of chrome leather particles has been found to improve the consumption of scrap rubber powder in natural rubber formulations. Polymer composites based on leather wastes as fillers are reported to be useful for many applications such as in construction materials, automobile interior moldings, heat and sound insulating boards, shoe soles, flooring materials and moldings with good anti-static properties, air permeability and good appearances.

  6. Status RVNRL in German latex industry and its introduction to the European market

    International Nuclear Information System (INIS)

    Bez, W.

    1996-01-01

    Reasons to look for an alternative crosslinking system avoiding sulphur curing was the restrictive policy of the German Health Authorities concerning nitrosamines. It was concluded that radiation curing offers further advantages . By avoiding the accelerators, type IV allergy is excluded, cytotoxicity is minimised to a very low level, films have better clarity and when thoroughly leached higher electrical resistance. Treatment of waste give no SO sub 2 emissions by burning, no Zinc in the ashes and possibly better microbial degradation. A development was carried out to irradiate natural latex by electron beam with a Dynamitron equipment. It was found trimethylolpropanetrimethacrylate to be a suitable sensitizer. Because of to high prices this development was interrupted. For future application trials and efforts to introduce RVNRL in the market gamma ray radiated natural latex either from Batan, Indonesia or MINT, Malaysia are used. Mainly dipped goods were produce, but radiated natural latex has shown good results in other processes. During discussions with customers it has proved necessary to establish specifications for RVNRL. A serious problem using natural latex for the production of medical devices is the type I allergy. Attempts are made to dip surgical gloves, leach them thoroughly and control extractable proteins were reduced to the very low level of 6.5 μg/g. Out of 18 patients sensitive to natural latex protein wearing gloves made from RVNRL only six have shown a positive response. That means RVNRL could help to solve the protein allergy problem. Further developments on this line are scheduled

  7. Identification of three homologous latex-clearing protein (lcp) genes from the genome of Streptomyces sp. strain CFMR 7.

    Science.gov (United States)

    Nanthini, Jayaram; Ong, Su Yean; Sudesh, Kumar

    2017-09-10

    Rubber materials have greatly contributed to human civilization. However, being a polymeric material does not decompose easily, it has caused huge environmental problems. On the other hand, only few bacteria are known to degrade rubber, with studies pertaining them being intensively focusing on the mechanism involved in microbial rubber degradation. The Streptomyces sp. strain CFMR 7, which was previously confirmed to possess rubber-degrading ability, was subjected to whole genome sequencing using the single molecule sequencing technology of the PacBio® RS II system. The genome was further analyzed and compared with previously reported rubber-degrading bacteria in order to identify the potential genes involved in rubber degradation. This led to the interesting discovery of three homologues of latex-clearing protein (Lcp) on the chromosome of this strain, which are probably responsible for rubber degrading activities. Genes encoding oxidoreductase α-subunit (oxiA) and oxidoreductase β-subunit (oxiB) were also found downstream of two lcp genes which are located adjacent to each other. In silico analysis reveals genes that have been identified to be involved in the microbial degradation of rubber in the Streptomyces sp. strain CFMR 7. This is the first whole genome sequence of a clear-zone-forming natural rubber- degrading Streptomyces sp., which harbours three Lcp homologous genes with the presence of oxiA and oxiB genes compared to the previously reported Gordonia polyisoprenivorans strain VH2 (with two Lcp homologous genes) and Nocardia nova SH22a (with only one Lcp gene). Copyright © 2017 Elsevier B.V. All rights reserved.

  8. Magnetic rubber inspection (MRI)

    International Nuclear Information System (INIS)

    Carro, L.

    1997-01-01

    Magnetic Rubber Inspection (MRI) was developed to inspect for small cracks and flaws encountered in high performance aircraft. A formula of very fine magnetic particles immersed in a room temperature curing rubber is catalysed and poured into dams (retainers) on the surface of the part to be inspected. Inducing a magnetic field then causes the particles to be drawn to discontinuities in the component under test. These indicating particles are held to the discontinuity by magnetic attraction, as the rubber cures. The solid rubber cast (Replica) is then removed and examined under a microscope for indicating lines of particle concentrations. 3 refs., 6 figs

  9. Predição de parâmetros e valores genéticos para caracteres de crescimento e produção de látex em progênies de seringueira Genetic parameters and values prediction for growth and latex production traits in rubber tree progenies

    Directory of Open Access Journals (Sweden)

    Reginaldo Brito da Costa

    2010-01-01

    Full Text Available O trabalho objetivou estimar parâmetros e valores genéticos para os caracteres altura, diâmetro, produção de látex e produtividade de progênies de seringueira. As progênies meio-irmãos foram estabelecidas sob delineamento de blocos ao acaso, com 28 tratamentos (progênies, cinco repetições e dez plantas por parcela. Aos três anos de idade, as progênies foram avaliadas quanto aos caracteres: a altura total (cm; b diâmetro (mm; c Produção de borracha seca (g e produtividade (g cm-2. As estimativas dos coeficientes de herdabilidades individuais (0,33; 0,24 e 0,51 para os caracteres altura, diâmetro e produtividade, respectivamente, foram consideradas expressivas. Para o caráter produção de borracha seca, a estimativa do coeficiente de herdabilidade individual, no sentido restrito (9%, embora de baixa magnitude, revela excelente possibilidade de seleção, pois conduziram a estimativa da herdabilidade, em nível de médias de família, a um valor equivalente a 68%. A acurácia entre os valores genéticos preditos e os verdadeiros foram de 0,80 para altura, 0,76 para diâmetro, 0,62 para produção de borracha seca e 0,86 para produtividade. As estimativas de herdabilidades individuais associadas às de médias de progênies podem maximizar os ganhos genéticos com a seleção na população. A inclusão do caráter produtividade foi promissora e deve ser utilizada na seqüência das avaliações, subsidiando o programa de melhoramento genético da espécie no Estado de Mato Grosso do Sul.This study aimed to estimate genetic values and parameters for plant height, diameter, rubber yield and productivity (g cm-2 of rubber tree progenies. Half-sib progenies were established in a complete randomized block, with 28 treatments, five replicates and 10 plants per plot. At three years of life, the progenies were evaluated regarding the following characters: diameter, rubber production and productivity (g cm². The estimative coefficients

  10. Effect of concentrated epoxidised natural rubber and silica masterbatch for tyre application

    Energy Technology Data Exchange (ETDEWEB)

    Azira, A. A., E-mail: azira@lgm.gov.my; Kamal, M. M., E-mail: mazlina@lgm.gov.my [High Value Added Rubber Products and Nanostructured Materials, Stesen Penyelidikan RRIM, LGM 47000 Sungai Buloh, Selangor (Malaysia); Verasamy, D., E-mail: devaraj@lgm.gov.my [Environmental Technology & Sustainability, Technology & Engineering Division, Malaysian Rubber Board, Stesen Penyelidikan RRIM, LGM 47000 Sungai Buloh, Selangor (Malaysia)

    2016-07-06

    The availability of concentrated epoxidised natural rubber (ENR-LC) has provided a better opportunity for using epoxidised natural rubber (ENR) with silica to reinforce natural rubber for tyre application. ENR-LC mixed directly with silica to rubber by high speed stirrer without using any coupling agent. Some rubber compounds were prepared by mixing a large amount of precipitated amorphous white silica with natural rubber. The silica was prepared in aqueous dispersion and the filler was perfectly dispersed in the ENR-LC. The performance of the composites was evaluated in this work for the viability of ENR-LC/Si in tyre compounding. Compounding was carried out on a two roll mill, where the additives and curing agents was later mixed. Characterization of these composites was performed by Field Emission Scanning Electron Microscopy (FESEM) and Transmission Electron Microscopy (TEM) for dispersion as well as mechanical testing. C-ENR/Si showed efficient as primary reinforcing filler in ENR with regard to modulus and tensile strength, resulting on an increase in the stiffness of the rubbers compared to ENR latex. Overall improvement in the mechanical properties for the ENR-LC over the control crosslinked rubber sample was probably due to synergisms of silica reinforcement and crosslinking of the polymeric matrix phase.

  11. Effect of concentrated epoxidised natural rubber and silica masterbatch for tyre application

    International Nuclear Information System (INIS)

    Azira, A. A.; Kamal, M. M.; Verasamy, D.

    2016-01-01

    The availability of concentrated epoxidised natural rubber (ENR-LC) has provided a better opportunity for using epoxidised natural rubber (ENR) with silica to reinforce natural rubber for tyre application. ENR-LC mixed directly with silica to rubber by high speed stirrer without using any coupling agent. Some rubber compounds were prepared by mixing a large amount of precipitated amorphous white silica with natural rubber. The silica was prepared in aqueous dispersion and the filler was perfectly dispersed in the ENR-LC. The performance of the composites was evaluated in this work for the viability of ENR-LC/Si in tyre compounding. Compounding was carried out on a two roll mill, where the additives and curing agents was later mixed. Characterization of these composites was performed by Field Emission Scanning Electron Microscopy (FESEM) and Transmission Electron Microscopy (TEM) for dispersion as well as mechanical testing. C-ENR/Si showed efficient as primary reinforcing filler in ENR with regard to modulus and tensile strength, resulting on an increase in the stiffness of the rubbers compared to ENR latex. Overall improvement in the mechanical properties for the ENR-LC over the control crosslinked rubber sample was probably due to synergisms of silica reinforcement and crosslinking of the polymeric matrix phase.

  12. Latex glove sensitivity amongst diagnostic imaging healthcare ...

    African Journals Online (AJOL)

    kemrilib

    Sciences, Faculty of Health Sciences and Technology, University of Nigeria, Enugu Campus, Enugu. State, Nigeria. .... Occupation. No of .... latex protein residue and act as a hapten or .... at Work Act, 1989 and the safety, Health and Welfare at.

  13. Carbon Stocks across a Fifty Year Chronosequence of Rubber Plantations in Tropical China

    Directory of Open Access Journals (Sweden)

    Chenggang Liu

    2017-06-01

    Full Text Available Transition from forest to rubber (Hevea brasiliensis Muell. Arg. plantation has occurred in tropical China for decades. Rubber has been planted on 1 million ha to provide raw materials to the rubber industry. The role of various-aged rubber plantations in carbon (C sequestration remains unclear. The biomass C accumulation including latex C and C distribution in soil of five different-aged stands (7, 13, 19, 25 and 47 years old were examined. The total biomass C stock (TBC and total net primary productivity (NPPtotal, whether with or without latex C, had a close quadratic relationship with stand age. Regardless of stand age, around 68% of the C was stored in aboveground biomass, and NPPlatex contributed to approximately 18% of C sequestration. Soil organic carbon stock in the 100-cm depth remained relatively stable, but it lost about 16.8 Mg ha−1 with stand age. The total ecosystem C stock (TEC across stands averaged 159.6, 174.4, 229.6, 238.1 and 291.9 Mg ha−1, respectively, of which more than 45% was stored in the soil. However, biomass would become the major C sink rather than soil over a maximal rubber life expectancy. Regression analysis showed that TEC for rubber plantation at 22 years is comparable to a baseline of 230.4 Mg ha−1 for tropical forest in China, and would reach the maximum value at around 54 years. Therefore, rubber plantation can be considered as alternative land use without affecting net forest ecosystem C storage. In addition to the potential C gains, a full set of ecosystem and economic properties have to be quantified in order to assess the trade-offs associated with forest-to-rubber transition.

  14. Degradation of polyisoprene rubber by newly isolated Bacillus sp. AF-666 from soil.

    Science.gov (United States)

    Shah, A A; Hasan, F; Shah, Z; Mutiullah; Hameed, A

    2012-01-01

    Various microorganisms were screened for their ability to degrade polyisoprene rubber (natural rubber latex gloves). Strain AF-666, newly isolated from a soil sample, was selected as the best strain having the ability to grow on polyisoprene containing plates. The strain identified as Bacillus sp. AF-666, was found to degrade polyisoprene rubber, both on basal agar plates (latex overlay) as well as in liquid medium. Qualitative analysis of degradation was done through scanning electron microscopy (SEM) and Fourier transform infrared (FTIR) spectroscopy SEM showed changes in surface morphology, like appearance of pits and cracks, and marked difference in transmittance spectra of test and control due to changes in the functional groups, was detected through FTIR. CO2 evolution as a result of rubber degradation, was calculated gravimetrically by Sturm Test. About 4.43 g/1 of CO2 was produced in case of test, whereas, 1.57 g/1 in case of control. The viable number of cells (CFU/ml) was also higher in test than in control. Present study may provide an opportunity for further studies on the applications of biotechnological processes as a tool for rubber waste management.

  15. Energy use in the rubber, and linoleum and plastics floor-covering sectors

    Energy Technology Data Exchange (ETDEWEB)

    1981-01-01

    Visits were made to 77 establishments producing linoleum and 16 establishments producing coated substrates to gather information on energy consumption, fuel types, and attitudes to energy management. Data are presented on percentages of electricity, wastes, fuel oil, gas, and coal consumed totally for plants visited and percentages consumed for establishments grouped under the following categories: new tires, remolded tires, solid rubber base, latex rubber base, and coated substrate industries. Data on energy consumed per employee and by size of buildings were determined. About 760 opportunities for saving energy within the 93 sites visited were identified with the greatest potential for saving energy identified as recovery of waste heat. (MCW)

  16. Biodiversity in rubber agroforests

    NARCIS (Netherlands)

    Beukema, Hendrien

    2013-01-01

    Jungle rubber tuinen zijn extensieve rubber agroforests die qua structuur op secundaire bossen lijken, en waarin wilde soorten door de boer worden getolereerd. Met het verdwijnen van het laaglandregenwoud rijst de vraag of de begroeiing die ervoor in de plaats komt een aantal kenmerken en functies

  17. Vulcanization of Rubber

    Indian Academy of Sciences (India)

    Temperature 140 -180°C. Sulfur. 2-3 parts per. 100 parts of rubber (phr). Accelerator 0.5-1.0 phr. ZnO ... out an experiment, he spilt a mixture of rubber and sulfur with other ingredients on a hot .... both carbon-sulfur and sulfur-nitrogen bonds -.

  18. [Prevention of adverse effects in latex allergic patients: organizing a latex safe operating theatre].

    Science.gov (United States)

    Bonalumi, Sabrina; Barbonaglia, Patrizia; Bertocchi, Carmen

    2006-01-01

    In 2001 the General Health Direction of Region Lombardia approved (decree n. 22303) a guideline for the prevention of latex allergic reactions in patients and health care workers. This document provides general recommendations in order to standardize behaviors in regional health care facilities. The reason is due to a rise in the incident of reactions to latex products in the last 20 years. Nowadays the prevalence is higher in certain risk groups (subjected to frequent and repeated exposures) rather than the general population. The aim of the project was to organize a latex safe operating theatre in the Ospedale Maggiore Policlinico, Mangiagalli e Regina Elena of Milan (Fondazione) and to standardize behaviors in order to prevent adverse effects in latex allergic patients. Thanks to the literature review and the creation of a multidisciplinar team, we produced a protocol. Therefore, we requested manufacturers the certification of the latex content of their products. Results and conclusion. When latex allergic patients need to undergone surgery in our hospital, a latex safe operating theatre is organized by personnel following a multidisciplinar protocol. No allergic reactions were experienced during surgical procedures after the creation of an environment as free as possible from latex contamination. The project will involve an emergency room, one room or more of a ward and of the outpatients department.

  19. Preparation and Characterization of Conducting Polymer Latices by Chemical Polymerization of Aniline or Anisidine in Presence of Latex: Study of Their Electroactivity and Anti-Corrosion Properties

    Directory of Open Access Journals (Sweden)

    Bakhshali Massoumi

    2013-06-01

    Full Text Available Poly (vinylacetate-co-butylmethacrylate was prepared in presence of potassium persulphate as an oxidizing agent in aqueous solution of dodecylbenzene sulfonate sodium as an emulsifying agent. Then, aniline was polymerized by chemical oxidation method at three different concentrations of aniline monomer (0.1, 0.2 and 0.3 M in toluene in presence of poly(vinylacetate-co-butylmethacrylate in order to obtain polyaniline/poly(vinylacetate-co-butylmethacrylate. To prepare conducting-latex of polyanisidine/poly(vinylacetate-co-butylmethacrylate the same method was employed as above for aniline monomer in obtaining conducting polyaniline/poly(vinylacetate-co-butylmethacrylate latex. In addition, the purification of conducting-latex polymers, polyaniline/poly(vinylacetate-co-butylmethacrylate and polyanisidine/poly(vinylacetate-co-butylmethacrylate was conducted and preparation of tin layer films of conducting-latex polymers was carried out by casting method on glassy lames. The electroactivity properties of the prepared latex-polymers, polyaniline/poly(vinylacetate-co-butylmethacrylate and polyanisidine/poly(vinylacetate-co-butylmethacrylate were investigated by cyclic voltammetery (CV. The voltamogrames showed that the latex films were electroactive. Because of conductivity and electroactivity, the obtained films may find applications in anti-corrosion coatings. The anti-corrosion properties of conducting-latex polymers were studied on aluminum surface by impedance technique. The structure of the prepared conducting-latex polymers was confirmed by Fourier transform infrared (FTIR. Finally, the electrical conductivity of synthesized conducting-latex polymers, polyaniline/poly(vinylacetate-co-butylmethacrylate and polyanisidine/poly(vinylacetate-co-butylmethacrylate was measured by four probe technique.

  20. Hydrogel coating of RVNRL film by electron beam irradiation

    International Nuclear Information System (INIS)

    Chantara Thevy Ratnam; Khairul Zaman Hj, Mohd Dahlan; Fumio Yoshii; Keizo Makuuchi

    1996-01-01

    The tackiness properties of Radiation Vulcanized Natural Rubber Latex (RVNRL) film surfaces coated by various monomers have been investigated in order to understand the suitable hydrogels which reduce the tackiness of the film. In this context , different types of monomers namely, N-vinyl-2-pyrrolidone (NVP), N,N-dimethyl amino ethyl amide (DMAEA), acrylic acid (AAc), N-butyl acrylate (n-BA) and 2-hydroxyethyl methacrylate (HEMA) as well as monomer mixtures have been tried with varying degrees of success. It was found that coating the RVNRL with 80% HEMA/20% n-BA by irradiation at 80 kGy using low Energy Electron Beam gave remarkable reduction in surface tackiness of the RVNRL film. Several other attempts were made such as priming with acid and aluminum sulfate, mixing the aluminum sulfate into the monomer and dipping the partially wet RVNRL film into the monomer to enhance the wettability of he monomers with the film. Studies on surface topography revealed that the decrease in tackiness with coating is due to the increase of the surface roughness at 80 kGy, irradiation dose

  1. A Mixed Application of Geographically Weighted Regression and Unsupervised Classification for Analyzing Latex Yield Variability in Yunnan, China

    Directory of Open Access Journals (Sweden)

    Oh Seok Kim

    2017-05-01

    Full Text Available This paper introduces a mixed method approach for analyzing the determinants of natural latex yields and the associated spatial variations and identifying the most suitable regions for producing latex. Geographically Weighted Regressions (GWR and Iterative Self-Organizing Data Analysis Technique (ISODATA are jointly applied to the georeferenced data points collected from the rubber plantations in Xishuangbanna (in Yunnan province, south China and other remotely-sensed spatial data. According to the GWR models, Age of rubber tree, Percent of clay in soil, Elevation, Solar radiation, Population, Distance from road, Distance from stream, Precipitation, and Mean temperature turn out statistically significant, indicating that these are the major determinants shaping latex yields at the prefecture level. However, the signs and magnitudes of the parameter estimates at the aggregate level are different from those at the lower spatial level, and the differences are due to diverse reasons. The ISODATA classifies the landscape into three categories: high, medium, and low potential yields. The map reveals that Mengla County has the majority of land with high potential yield, while Jinghong City and Menghai County show lower potential yield. In short, the mixed method can offer a means of providing greater insights in the prediction of agricultural production.

  2. Anti-ulcer activity of Synadenium grantii latex

    Directory of Open Access Journals (Sweden)

    Larissa L. G. Costa

    2012-10-01

    Full Text Available Synadenium grantii Hook f., Euphorbiaceae, is popularly known as leitosinha or janaúba. The diluted latex (18 drops/L of water is commonly used in the south of Brazil to treat gastric disturbances. This study evaluated phytochemical screening and toxicity using Artemia salina Leach of crude bark extract and also latex. The toxicity and the anti-ulcer activity of S. grantii latex were also tested in rats. Phytochemical results showed presence of tannins, terpenes, unsaponificable substances, coumarins and anthraquinones in the crude bark extract and terpenes in the latex. Gas chromatography-mass spectrometry (GC-MS analysis demonstrated the presence of diterpene tigliane esters in the latex, identified as 12-deoxyphorbol-13-(2-metilpropionate and phorbol 12,13,20-triacetate. The toxicity results using A. salina presented CL50 26.58μg/mL and CL50 778.66μg/mL, for the latex and the crude bark extract respectively. The toxicological hepatic parameters of the diluted latex were not different to the control group (p<0.05. The eosinophils cells showed an increase in both the diluted and pure latex groups. The pure latex showed gastric protection of 90% (p<0.05 and the diluted latex showed 6% compared to the negative control. Therefore, our data indicate that S. grantii latex, under research conditions presented gastric protection. Pure latex showed more toxicity than the diluted latex.

  3. Radiation vulcanization of rubbers

    Energy Technology Data Exchange (ETDEWEB)

    Makuuchi, Keizo [Japan Atomic Energy Research Inst., Takasaki, Gunma (Japan). Takasaki Radiation Chemistry Research Establishment

    2002-02-01

    An abstract of the radiation process of polymer materials and the polymer reaction by radiation is explained. Main radiation is 250 keV to 10 MeV of electron rays in the industry. Radiation cross-linked rubber has less the tensile strength than that by sulfur and organic peroxide crosslinking. The main origins of low tensile strength are caused by cut of backbone chain and ozone depend on radiation. Acceleration of crosslinking and short time of radiation are necessary to improve these defects. To accelerate crosslinking, we used crosslinking accelerators, for example, three poly-functional monomers (PFM). The maximum tensile strength of styrene-butadiene rubber (SBR) not added crosslinking accelerators showed 3 MPa at 110 kGy, but SBR added A-TMMT (tetramethylolmethane tetraacrylate) showed 5.5 MPa at 110 kGy. Radiation crosslinking of many kinds of rubber: isoprene (IR), SBR, CR, nitrile rubber (NBR), hydrogenated nitrile rubber (HNBR), butyl rubber (IIR), chlorinated butyl rubber (CIIR), EPM and TPE are explained. (S.Y.)

  4. Multilayer graphene rubber nanocomposites

    Science.gov (United States)

    Schartel, Bernhard; Frasca, Daniele; Schulze, Dietmar; Wachtendorf, Volker; Krafft, Bernd; Morys, Michael; Böhning, Martin; Rybak, Thomas

    2016-05-01

    Multilayer Graphene (MLG), a nanoparticle with a specific surface of BET = 250 m2/g and thus made of only approximately 10 graphene sheets, is proposed as a nanofiller for rubbers. When homogenously dispersed, it works at low loadings enabling the replacement of carbon black (CB), increase in efficiency, or reduction in filler concentration. Actually the appropriate preparation yielded nanocomposites in which just 3 phr are sufficient to significantly improve the rheological, curing and mechanical properties of different rubbers, as shown for Chlorine-Isobutylene-Isoprene Rubber (CIIR), Nitrile-Butadiene Rubber (NBR), Natural Rubber (NR), and Styrene-Butadiene Rubber (SBR). A mere 3 phr of MLG tripled the Young's modulus of CIIR, an effect equivalent to 20 phr of carbon black. Similar equivalents are observed for MLG/CB mixtures. MLG reduces gas permeability, increases thermal and electrical conductivities, and retards fire behavior. The later shown by the reduction in heat release rate in the cone calorimeter. The higher the nanofiller concentration is (3 phr, 5 phr, and 10 phr was investigated), the greater the improvement in the properties of the nanocomposites. Moreover, the MLG nanocomposites improve stability of mechanical properties against weathering. An increase in UV-absorption as well as a pronounced radical scavenging are proposed and were proved experimentally. To sum up, MLG is interesting as a multifunctional nanofiller and seems to be quite ready for rubber development.

  5. Radiation vulcanization of rubbers

    International Nuclear Information System (INIS)

    Makuuchi, Keizo

    2002-01-01

    An abstract of the radiation process of polymer materials and the polymer reaction by radiation is explained. Main radiation is 250 keV to 10 MeV of electron rays in the industry. Radiation cross-linked rubber has less the tensile strength than that by sulfur and organic peroxide crosslinking. The main origins of low tensile strength are caused by cut of backbone chain and ozone depend on radiation. Acceleration of crosslinking and short time of radiation are necessary to improve these defects. To accelerate crosslinking, we used crosslinking accelerators, for example, three poly-functional monomers (PFM). The maximum tensile strength of styrene-butadiene rubber (SBR) not added crosslinking accelerators showed 3 MPa at 110 kGy, but SBR added A-TMMT (tetramethylolmethane tetraacrylate) showed 5.5 MPa at 110 kGy. Radiation crosslinking of many kinds of rubber: isoprene (IR), SBR, CR, nitrile rubber (NBR), hydrogenated nitrile rubber (HNBR), butyl rubber (IIR), chlorinated butyl rubber (CIIR), EPM and TPE are explained. (S.Y.)

  6. US rubber markets recover

    International Nuclear Information System (INIS)

    Wood, A.

    1993-01-01

    Synthetic rubber markets in North America bounced back in no uncertain terms last year, with demand climbing an impressive 9.5%, to 2.97 million m.t.; and, according to the International Institute of Synthetic Rubber Producers (IIS-RP; Houston) latest five-year forecast, producers can look forward to a 3.3% increase in demand during 1993. This growth rate outpaced out 1992 forecast and demonstrates the resilience of the synthetic rubber industry, says William E. Tessemer, managing director of IISRP. We expect demand in 1993 to surpass 1992 and level off at a 2%/year growth rate for synthetic rubber - 2.5% including thermoplastic elastomers [TPEs]-over the 1993-97 period. The improvement reflects signs of a recovery in North America, especially the pickup in the auto and tire industry. The two major tire rubbers - styrene butadiene and polybutadiene rubber - notched up double-digit gains, and other materials that have autos uses, such as nitrile rubber and many of the specialty elastomers, also advanced strongly

  7. Recombinant albumin monolayers on latex particles.

    Science.gov (United States)

    Sofińska, Kamila; Adamczyk, Zbigniew; Kujda, Marta; Nattich-Rak, Małgorzata

    2014-01-14

    The adsorption of recombinant human serum albumin (rHSA) on negatively charged polystyrene latex micro-particles was studied at pH 3.5 and the NaCl concentration range of 10(-3) to 0.15 M. The electrophoretic mobility of latex monotonically increased with the albumin concentration in the suspension. The coverage of adsorbed albumin was quantitatively determined using the depletion method, where the residual protein concentration was determined by electrokinetic measurements and AFM imaging. It was shown that albumin adsorption was irreversible. Its maximum coverage on latex varied between 0.7 mg m(-2) for 10(-3) M NaCl to 1.3 mg m(-2) for 0.15 M NaCl. The latter value matches the maximum coverage previously determined for human serum albumin on mica using the streaming potential method. The increase in the maximum coverage was interpreted in terms of reduced electrostatic repulsion among adsorbed molecules. These facts confirm that albumin adsorption at pH 3.5 is governed by electrostatic interactions and proceeds analogously to colloid particle deposition. The stability of albumin monolayers was measured in additional experiments where changes in the latex electrophoretic mobility and the concentration of free albumin in solutions were monitored over prolonged time periods. Based on these experimental data, a robust procedure of preparing albumin monolayers on latex particles of well-controlled coverage and molecule distribution was proposed.

  8. The Morphology of Emulsion Polymerized Latex Particles

    Science.gov (United States)

    Wignall, G. D.; Ramakrishnan, V. R.; Linne, M. A.; Klein, A.; Sperling, L. H.; Wai, M. P.; Gelman, R. A.; Fatica, M. G.; Hoerl, R. H.; Fisher, L. W.

    1987-11-01

    Under monomer starved feed conditions, emulsion polymerization of perdeuterated methyl methacrylate and styrene in the presence of preformed polymethylmethacrylate latexes resulted in particles with a core-shell morphology, as determined by small-angle neutron scattering (SANS) analysis for a hollow sphere. The locus of polymerization of the added deuterated monomer is therefore at the particle surface. In similar measurements a statistical copolymer of styrene and methyl methacrylate was used as seed particles for further polymerization of trideuteromethyl methacrylate. The resulting polymer latex was again shown to have a core-shell morphological structure as determined by SANS. SANS experiments were also undertaken on polystyrene latexes polymerized by equilibrium swelling methods, with deuterated polymer forming the first or second step. The experiments covered a molecular weight range of 6 x 10{sup 4} 10{sup 6} the molecular weights are consistent with the experimental errors, indicating that the deuterium labeled molecules are randomly distributed in the latex. These results led to the finding that the polymer chains were constrained in the latex particles by factors of 2 to 4 from the relaxed coil dimensions. For M molecules. Several models were examined, including the possible development of core-shell structures at lower molecular weights.

  9. Dragon Fruit Foliage Plant-Based Coagulant for Treatment of Concentrated Latex Effluent: Comparison of Treatment with Ferric Sulfate

    Directory of Open Access Journals (Sweden)

    Juferi Idris

    2013-01-01

    Full Text Available The effectiveness of dragon fruit foliage as a natural coagulant for treatment of concentrated latex effluent was investigated and compared with ferric sulfate, a chemical coagulant. Dragon fruit is a round and often red-colored fruit with scales-like texture and is native to south American countries which is also cultivated and heavily marketed in southeast Asian countries. Its foliage represents a part of its overall plant system. Latex effluent is one of the main byproduct from rubber processing factories in Malaysia. Three main parameters investigated were chemical oxygen demand (COD, suspended solids (SS, and turbidity of effluent. Coagulation experiments using jar test were performed with a flocculation system where the effects of latex effluent pH as well as coagulation dosage on coagulation effectiveness were examined. The highest recorded COD, SS, and turbidity removal percentages for foliage were observed for effluent pH 10 at 94.7, 88.9, and 99.7%, respectively. It is concluded that the foliage showed tremendous potential as a natural coagulant for water treatment purposes. The foliage could be used in the pretreatment stage of Malaysian latex effluent prior to secondary treatment.

  10. Polymer Electrolyte Prepared from Highly Deproteinized Natural Rubber Having Epoxy Group

    Science.gov (United States)

    Klinklai, W.; Kawahara, S.; Isono, Y.; Mizumo, T.; Yoshizawa, M.; Ohno, H.

    Deproteinized natural rubber having epoxy group (EDPNR) was applied to transport Li+ as a solid polymer electrolyte. The deproteinized natural rubber, incubated with proteolytic enzyme and surfactant, was subjected to epoxidation followed by oxidative depolymerization in latex stage. The resulting rubber was proved to be a liquid deproteinized natural rubber (LEDPNR) having polar epoxy groups, low Tg, low Mn and well-defined terminal units. Ionic conductivity of LEDPNR mixed with alkali metal salts was investigated through impedance analysis to clarify an effect of proteins present in the rubber. The ionic conductivity of the resulting LEDPNR depended on the kind of salts, their concentrations and temperature. The ionic conductivity of LEDPNR/lithium bis(trifluoromethan sulfonyl)imide (LiTFSI) was higher than that of LEDPNR/ lithium perchlorate (LiClO4). The difference in the ionic conductivity was attributed to the solubility of the salts as results of both high-resolution solid-state 13C-NMR spectroscopy and measurements of spin-lattice relaxation time. The conductivity of LEDPNR/LiTFSI was also dependent upon concentrations of LiTFSI and it reached the highest value at 20 wt%, which was different from the monotonic increase in the Li+ conductivity of liquid epoxidized natural rubber prepared from untreated natural rubber.

  11. Home Healthcare Workers: How to Prevent Latex Allergies

    Science.gov (United States)

    ... can help prevent allergic reactions for both home healthcare workers and their clients. LATEX EXPOSURE REACTIONS Three ... being used). • Inform your employer and your personal healthcare professionals that you have latex allergy. • Wear a ...

  12. Angiogenic activity of Synadenium umbellatum Pax latex

    Directory of Open Access Journals (Sweden)

    PR. Melo-Reis

    Full Text Available Synadenium umbellatum Pax, popularly known as "cola-nota", is a medicinal plant that grows in tropical regions. Latex of this plant is used to treat various diseases such as diabetes mellitus, Hansen´s disease, tripanosomiases, leukemia and several malignant tumors. In the present study, the angiogenic activity of S. umbellatum latex was evaluated using the chick embryo chorioallantoic membrane (CAM assay. Results showed significant increase of the vascular net (p < 0.05 compared to the negative control (H2O. The histological analysis was in accordance with the results obtained. In conclusion, our data indicate that S. umbellatum latex, under the conditions of this research, presented angiogenic effect.

  13. Synthesis, characterization and degradation behavior of admicelled polyacrylate-natural rubber

    International Nuclear Information System (INIS)

    Pongpilaipruet, Angkana; Magaraphan, Rathanawan

    2015-01-01

    In order to improve weatherability of the cured natural rubber, the novel introduction of good ozone resistant polymers such as polyacrylates (poly(methyl acrylate) (PMA) or poly(methyl methacrylate) (PMMA)) into natural rubber (NR) by admicellar polymerization was investigated in this work. The admicellar polymerization to synthesize polyacrylate layer over the surface of NR latex particles was performed with varying monomer type (PMA and PMMA) and content (50 and 100 mM). The admicelled PMMA showed higher molecular weight than PMA. Fourier transform infrared spectra of the admicellar synthesized natural rubbers exhibited characteristic peaks of those polyacrylates. Micrographs from transmission electron and field emission scanning electron microscopes (FE-SEM) revealed the coatings of PMA and PMMA over the rubber particles, suggesting a core-shell structure. Thermogravimetric analysis revealed that the admicelled rubbers not only showed an improvement in heat stability but also a single decomposition temperature. After vulcanization, FE-SEM results showed the cured admicelled rubbers had phase transformation from core-shell to phase separation (aggregate domains of polyacrylate-rich phase) with smooth interface. This agreed well to their one glass transition temperature (∼−48 °C) which indicated good miscibility between NR and each polyacrylate. The cracks generated after exposure to ozone found in the admicelled rubbers were smaller than those in NR, suggesting better ozone resistance was achieved. Increasing monomer concentration led to less cracks or much better ozone resistance. Furthermore, changes in mechanical properties after ozone exposure of the admicelled PMA-NR were less than those of the admicelled PMMA-NR (having the same shell content) and the NR, respectively. - Highlights: • We use admicellar technique to add polyacrylates to NR in form of core-shell rubber. • This core-shell structure was physically formed as seen by the phase

  14. Synthesis, characterization and degradation behavior of admicelled polyacrylate-natural rubber

    Energy Technology Data Exchange (ETDEWEB)

    Pongpilaipruet, Angkana; Magaraphan, Rathanawan, E-mail: rathanawan.k@chula.ac.th

    2015-06-15

    In order to improve weatherability of the cured natural rubber, the novel introduction of good ozone resistant polymers such as polyacrylates (poly(methyl acrylate) (PMA) or poly(methyl methacrylate) (PMMA)) into natural rubber (NR) by admicellar polymerization was investigated in this work. The admicellar polymerization to synthesize polyacrylate layer over the surface of NR latex particles was performed with varying monomer type (PMA and PMMA) and content (50 and 100 mM). The admicelled PMMA showed higher molecular weight than PMA. Fourier transform infrared spectra of the admicellar synthesized natural rubbers exhibited characteristic peaks of those polyacrylates. Micrographs from transmission electron and field emission scanning electron microscopes (FE-SEM) revealed the coatings of PMA and PMMA over the rubber particles, suggesting a core-shell structure. Thermogravimetric analysis revealed that the admicelled rubbers not only showed an improvement in heat stability but also a single decomposition temperature. After vulcanization, FE-SEM results showed the cured admicelled rubbers had phase transformation from core-shell to phase separation (aggregate domains of polyacrylate-rich phase) with smooth interface. This agreed well to their one glass transition temperature (∼−48 °C) which indicated good miscibility between NR and each polyacrylate. The cracks generated after exposure to ozone found in the admicelled rubbers were smaller than those in NR, suggesting better ozone resistance was achieved. Increasing monomer concentration led to less cracks or much better ozone resistance. Furthermore, changes in mechanical properties after ozone exposure of the admicelled PMA-NR were less than those of the admicelled PMMA-NR (having the same shell content) and the NR, respectively. - Highlights: • We use admicellar technique to add polyacrylates to NR in form of core-shell rubber. • This core-shell structure was physically formed as seen by the phase

  15. CHARACTERIZATION AND RECYCLING OF WASTE WATER FROM GUAYULE LATEX EXTRACTION

    Science.gov (United States)

    Guayule commercialization for latex production to be used in medical products and other applications is now a reality. Currently, waste water following latex extraction is discharged into evaporation ponds. As commercialization reaches full scale, the liquid waste stream from latex extraction will b...

  16. Plant latex lipase as biocatalysts for biodiesel production | Mazou ...

    African Journals Online (AJOL)

    Plant latex lipase as biocatalysts for biodiesel production. ... This paper provides an overview regarding the main aspects of latex, such as the reactions catalyzed, physiological functions, specificities, sources and their industrial applications. Keywords: Plant latex, lipase, Transesterification, purification, biodiesel ...

  17. Thermodynamics of swelling of latex particles with two monomers

    NARCIS (Netherlands)

    Maxwell, I.A.; Kurja, J.; van Doremaele, G.H.J.; German, A.L.

    1992-01-01

    The partitioning of 2 monomers between the latex particle, monomer droplet, and aq. phases of an emulsion polymer latex are measured at satn. swelling of the latex particle phase (corresponding to intervals I and II of an emulsion polymn.). The monomer (Me acrylate, Bu acrylate, styrene) and polymer

  18. Emotion with tears decreases allergic responses to latex in atopic eczema patients with latex allergy.

    Science.gov (United States)

    Kimata, Hajime

    2006-07-01

    Allergic responses are enhanced by stress, whereas they are reduced by laughter in atopic eczema patients. Emotion with tears decreases plasma IL-6 levels in patients with rheumatoid arthritis. Thus, the effect of emotion with tears on allergic responses in patients with atopic eczema was studied. Sixty patients with atopic eczema having latex allergy viewed both the weather information video and the heart-warming movie, Kramer vs. Kramer. Just before and immediately after viewing each video, allergic responses to latex were measured. Viewing the weather information video did not cause emotion with tears in any patients, and it failed to modulate allergic responses. In contrast, viewing Kramer vs. Kramer caused emotion with tears in 44 of 60 patients, and it reduced allergic skin wheal responses to latex and latex-specific IgE production in them. Emotion with tears reduced allergic responses, and it may be useful in the treatment of allergic diseases.

  19. Mechanical Enhancement of Sensitivity in Natural Rubber Using Electrolytic Polymerization Aided by a Magnetic Field and MCF for Application in Haptic Sensors.

    Science.gov (United States)

    Shimada, Kunio; Saga, Norihiko

    2016-09-18

    Sensors are essential to the fulfillment of every condition of haptic technology, and they need simultaneously to sense shear stress as well as normal force, and temperature. They also must have a strong and simple structure, softness, and large extension. To achieve these conditions simultaneously, we enhanced the sensitivity of sensors utilizing natural rubber (NR)-latex through the application of electrolytic polymerization focused on the isoprene C=C bonds in natural rubbers such as NR-latex, and then applied a magnetic field and magnetic compound fluid (MCF) as magnetically responsive fluid. When an electric field alone was used in the rubber, the effect of electrolytic polymerization was very small compared to the effect in well-known conductive polymer solution such as plastic. The MCF developed by Shimada in 2001 involved magnetite and metal particles, and acts as a filler in NR-latex. By utilizing the magnetic, electric fields and the MCF, we aligned the electrolytically polymerized C=C along the magnetic field line with the magnetic clusters formed by the aggregation of magnetite and metal particles so as to enhance the effect of electrolytic polymerization. We then demonstrated the effectiveness of the new method of rubber vulcanization on the sensitivity of the rubber by experimentally investigating its electric and dynamic characteristics.

  20. Mechanical Enhancement of Sensitivity in Natural Rubber Using Electrolytic Polymerization Aided by a Magnetic Field and MCF for Application in Haptic Sensors

    Directory of Open Access Journals (Sweden)

    Kunio Shimada

    2016-09-01

    Full Text Available Sensors are essential to the fulfillment of every condition of haptic technology, and they need simultaneously to sense shear stress as well as normal force, and temperature. They also must have a strong and simple structure, softness, and large extension. To achieve these conditions simultaneously, we enhanced the sensitivity of sensors utilizing natural rubber (NR-latex through the application of electrolytic polymerization focused on the isoprene C=C bonds in natural rubbers such as NR-latex, and then applied a magnetic field and magnetic compound fluid (MCF as magnetically responsive fluid. When an electric field alone was used in the rubber, the effect of electrolytic polymerization was very small compared to the effect in well-known conductive polymer solution such as plastic. The MCF developed by Shimada in 2001 involved magnetite and metal particles, and acts as a filler in NR-latex. By utilizing the magnetic, electric fields and the MCF, we aligned the electrolytically polymerized C=C along the magnetic field line with the magnetic clusters formed by the aggregation of magnetite and metal particles so as to enhance the effect of electrolytic polymerization. We then demonstrated the effectiveness of the new method of rubber vulcanization on the sensitivity of the rubber by experimentally investigating its electric and dynamic characteristics.

  1. Filled liquid silicone rubbers: Possibilities and challenges

    DEFF Research Database (Denmark)

    Yu, Liyun; Vudayagiri, Sindhu; Zakaria, Shamsul Bin

    2014-01-01

    to ensure better particle dispersion as well as folllowing for film formation properties. We show that the mechanical properties of the films as well as the electrical breakdown strength can be affected, and that the control of the amount of solvent throughout the coating process is essential for solvent......Liquid silicone rubbers (LSRs) have been shown to possess very favorable properties as dielectric electroactive polymers due to their very high breakdown strengths (up to 170 V/μm) combined with their fast response, relatively high tear strength, acceptable Young’s modulus as well as they can...

  2. Preparation and characterization of nanocomposites of natural rubber with polystyrene and styrene-methacrylic acid copolymer nanoparticles

    Directory of Open Access Journals (Sweden)

    T. Nuruk

    2012-06-01

    Full Text Available Composites of natural rubber (NR/vinyl polymer nanoparticles as polystyrene (PS and poly(styrenemethacrylic acid (P(S-MAA were prepared by heterocoagulation technique. The polymer nanoparticles were prepared by emulsifier-free emulsion polymerizations at 70°C using potassium persulfate as initiator. Under acidic condition where positive charge was present on the NR latex (NRL surface, the nanoparticles having negative charge mainly from sulfate group of initiator were able to adsorb on the NRL surface, the electrostatic interaction being the driving force. The scanning electron micrographs showed that the polymer nanoparticles are homogenously distributed throughout NR matrix as nanoclusters with an average size of about 500 and 200 nm for PS and P(S-MAA, respectively. The mechanical properties of NR/PS and NR/P(S-MAA composite films were compared with the NR host. The nanocomposites, particularly when the polymer nanoparticles are uniformly dispersed, possess significantly enhanced mechanical properties strongly depending on the morphology of the nanocomposites.

  3. CHEMICAL EXAMINATION OF JACK TREE LATEX AND

    Indian Academy of Sciences (India)

    and on Saponification yielded fatty acids, Volatile as well as non-volatile. The unsaponifiable portion on repeated crystallisation provided a crystal- line, sharp melting compound which was identified as artostenone? from a. Latex (200 c.c.). ത്ത min- pe. Coagulum (A) Aqueous alcoholic solution (B). Acetone or ethyl acetate ...

  4. Appointments on rubber economy and the exploitation of indigenous labor in Rondônia

    Directory of Open Access Journals (Sweden)

    Carlos Alexandre Barros Trubiliano

    2017-12-01

    Full Text Available The turn of the nineteenth to the twentieth century was marked by the expansion of economic activities in the Amazon region, causing deep socio-spatial impacts. Driven by international rubber demands, sheds, ports and roads were erected. Under the aegis of the progress discourse, thousands of workers were co-opted to labor in the extraction of latex. In the rubber plantations, relations were marked by violence. This essay presents notes on the exploitation of indigenous labor in the formation of rubber plantations in Rondônia. We deal with worker's coping strategies, working conditions and interethnic contact. Our objective was to contribute to the debate about the expansion of capitalist relations in the Amazon region and the impacts of this process on the indigenous populations of Rondônia.

  5. DEB-silicone rubber hydrogen absorbing Raman detection technology research

    International Nuclear Information System (INIS)

    Yang Suolong; Zhong Jingrong; Wang Huang; Yang Kaixu; Xiao Jiqun; Liu Jiaxi; Liao Junsheng

    2012-01-01

    The DEB-Pd/C hydrogen getter powder and DEB-Pd/C-silicone rubber getter film were prepared and used for hydrogen detection in close systems by laser Raman method. The DEB alkanes Raman peak intensity changes with the getter time were monitored by Raman spectrometer. As a result, silicone rubber has good compatibility with DEB getter, slow access to hydrogen and good flexible. The alkanes peak intensity-getter time followed a exponential rule. DEB getter films are suitable for Raman on-line monitor of cumulative hydrogen of a closed system at long time. (authors)

  6. Triterpenoid biosynthesis in Euphorbia lathyris latex

    International Nuclear Information System (INIS)

    Hawkins, D.R.

    1987-11-01

    The structures of triterpenols, not previously been known, from Euphorbia lathyris latex are reported. A method for quantifying very small amounts of these compounds was developed. Concerning the biochemistry of the latex, no exogenous cofactors were required for the biosynthesis and the addition of compounds such as NADPAH and ATP do not stimulate the biosynthesis. The addition of DTE or a similar anti-oxidant was found to help reduce the oxidation of the latex, thus increasing the length of time that the latex remains active. The requirement of a divalent cation and the preference for Mn in the pellet was observed. The effect of several inhibitors on the biosynthesis of the triterpenoids was examined. Mevinolin was found to inhibit the biosynthesis of the triterpenoids from acetate, but not mevalonate. A dixon plot of the inhibition of acetate incorporation showed an I 50 concentration of 3.2 μM. Fenpropimorph was found to have little or no effect on the biosynthesis. Tridemorph was found to inhibit the biosynthesis of all of the triterpenoids with an I 50 of 4 μM. It was also observed that the cyclopropyl containing triterpenols, cycloartenol and 24-methylenecycloartenol were inhibited much more strongly than those containing an 8-9 double bond, lanosterol and 24-methylenelanosterol. The evidence indicates, but does not definetely prove, that lanosterol and 24-methylenelanosterol are not made from cycloartenol and 24-methylenecycloartenol via a ring-opening enzyme such as cycloeucalenol-obtusifoliol isomerase. The possibilty that cycloartenol is made via lanosterol was investigated by synthesizing 4-R-4- 3 H-mevalonic acid and incubating latex with a mixture of this and 14 C-mevalonic acid. From the 3 H/ 14 C ratio it was shown that cycloartenol and 24-methylenecycloartenol are not made via an intermediate containing as 8-9 double bond. 88 refs., 15 figs., 30 tabs

  7. Triterpenoid biosynthesis in Euphorbia lathyris latex

    Energy Technology Data Exchange (ETDEWEB)

    Hawkins, D.R.

    1987-11-01

    The structures of triterpenols, not previously been known, from Euphorbia lathyris latex are reported. A method for quantifying very small amounts of these compounds was developed. Concerning the biochemistry of the latex, no exogenous cofactors were required for the biosynthesis and the addition of compounds such as NADPAH and ATP do not stimulate the biosynthesis. The addition of DTE or a similar anti-oxidant was found to help reduce the oxidation of the latex, thus increasing the length of time that the latex remains active. The requirement of a divalent cation and the preference for Mn in the pellet was observed. The effect of several inhibitors on the biosynthesis of the triterpenoids was examined. Mevinolin was found to inhibit the biosynthesis of the triterpenoids from acetate, but not mevalonate. A dixon plot of the inhibition of acetate incorporation showed an I/sub 50/ concentration of 3.2 ..mu..M. Fenpropimorph was found to have little or no effect on the biosynthesis. Tridemorph was found to inhibit the biosynthesis of all of the triterpenoids with an I/sub 50/ of 4 ..mu..M. It was also observed that the cyclopropyl containing triterpenols, cycloartenol and 24-methylenecycloartenol were inhibited much more strongly than those containing an 8-9 double bond, lanosterol and 24-methylenelanosterol. The evidence indicates, but does not definetely prove, that lanosterol and 24-methylenelanosterol are not made from cycloartenol and 24-methylenecycloartenol via a ring-opening enzyme such as cycloeucalenol-obtusifoliol isomerase. The possibilty that cycloartenol is made via lanosterol was investigated by synthesizing 4-R-4-/sup 3/H-mevalonic acid and incubating latex with a mixture of this and /sup 14/C-mevalonic acid. From the /sup 3/H//sup 14/C ratio it was shown that cycloartenol and 24-methylenecycloartenol are not made via an intermediate containing as 8-9 double bond. 88 refs., 15 figs., 30 tabs.

  8. Current trend in latex dipped products manufacturing

    International Nuclear Information System (INIS)

    Wong, W.S.C.

    1996-01-01

    The paper present the activities in dipped products manufacturing in Malaysia; the activities carried out by MARGMA - Malaysian Rubber Glove manufacturer; other issues discussed such as labour, pricing environmental issue, product certification in this activity

  9. The Role of Remote Sensing for Understanding Large-Scale Rubber Concession Expansion in Southern Laos

    Directory of Open Access Journals (Sweden)

    Mutlu Özdoğan

    2018-04-01

    Full Text Available Increasing global demand for natural rubber began in the mid-2000s and led to large-scale expansion of plantations in Laos until rubber latex prices declined greatly beginning in 2011. The expansion of rubber did not, however, occur uniformly across the country. While the north and central Laos experienced mostly local and smallholder plantations, rubber expansion in the south was dominated by transnational companies from Vietnam, China and Thailand through large-scale land concessions, often causing conflicts with local communities. In this study we use satellite remote sensing to identify and map the expansion of large-scale rubber plantations in Champasak Province—the first area in southern Laos to host large-scale rubber development—and document the biophysical impacts on the local landscape, which of course is linked to social impacts on local people. Our study demonstrates that the expansion of rubber in the province was rapid and did not always conform to approved concession area locations. The mono-culture nature of rubber plantations also had the effect of homogenizing the landscape, eclipsing the changes caused by local populations. We argue that by providing a relatively inexpensive way to track the expansion of rubber plantations over space and time, remote sensing has the potential to provide advocates and other civil society groups with data that might otherwise remain limited to the restricted domains of state regulation and private sector reporting. However, we also caution that while remote sensing has the potential to provide strong public evidence about plantation expansion, access to and control of this information ultimately determines its value.

  10. Rubber seed oil: A potential renewable source of biodiesel for sustainable development in sub-Saharan Africa

    International Nuclear Information System (INIS)

    Onoji, Samuel E.; Iyuke, Sunny E.; Igbafe, Anselm I.; Nkazi, Diakanua B.

    2016-01-01

    ) are grown domestically in large plantations solely for latex production in most tropical SSA countries and the seeds fall out as waste to the ground either to germinate or are collected and discarded annually. However, SSA countries have an estimated combined capacity of 717,750 ha of rubber trees equivalent to 251 million trees that can generate on annual basis, about 107,662.5 ton of rubber seed, 17,947.339 ton of rubber seed oil and an equivalent 16,691.025 ton of biodiesel. The cultivation of natural rubber trees will sustain the production of rubber products from latex and seed oils for biodiesel which would create additional financial benefits to the plantation farmers and reinvigorates the economies of the local communities in SSA countries.

  11. Synthesis and characterization of novel fluoroalkyl-terminated hyperbranched polyurethane latex

    Science.gov (United States)

    Xu, Wei; Zhao, Weijia; Hao, Lifen; Wang, Sha; Pei, Mengmeng; Wang, Xuechuan

    2018-04-01

    Waterborne polyurethane (PU) emulsions are widely used in various fields and the demand for them is ever-increasing over the years. However, the hydrophilic chain extender inevitably bonded into the PU backbone can affect the water tolerance of PU. Thus, it is of great importance to improve PU water resistance effectively. Herein, novel fluoroalkyl-terminated hyperbranched polyurethane (HBPUF) latex was accordingly synthesized by graft reaction of perfluorohexyl ethyl alcohol and hyperbranched polyurethane (HBPU), which was previously obtained from interaction between hydroxyl-terminated hyperbranched polymer and PU prepolymer manufactured via the acetone process, as well as using neutralization, adding water, and high-speed stirring operations. We characterized the resultants and investigated its surface properties by IR, NMR, TEM, XRD, TGA, DSC, FE-SEM, AFM, XPS, and contact angle measurements, etc. IR and NMR tests confirmed that the fluorinated fragments had been grafted onto the tail end of HBPU. TEM, XRD, DSC, and FE-SEM results all accounted for the fact that there were multi-crystals in PU, HBPU and HBPUF. TGA results showed that thermal stabilities of the PU, HBPU, and HBPUF latex films were enhanced in turn. XPS and AFM analyses demonstrated that the fluorine-containing segments from the HBPUF terminals were prone to migrate and enrich on the film-air surface of the HBPUF latex film, which made water contact angle and water absorption of the HBPUF film be as 113.9° and 11.1%, respectively, compared to those of the PU film (77.8° and 136.2%). This research indicates that water resistance of the PU film can be efficiently enhanced by fluorinated polyurethane with novel fluoroalkyl-terminated hyperbranched structure.

  12. A comparative investigation on strain induced crystallization for graphene and carbon nanotubes filled natural rubber composites

    Directory of Open Access Journals (Sweden)

    D. H. Fu

    2015-07-01

    Full Text Available Natural rubber containing graphene and carbon nanotubes (CNTs composites were prepared by ultrasonicallyassisted latex mixing. Natural rubber filled by both graphene and CNTs show significant enhanced tensile strength, while graphene exhibits a better reinforcing effect than CNTs. Strain-induced crystallization in natural rubber composites during stretching was determined by synchrotron wide-angle X-ray diffraction. With the addition of CNTs or graphene, the crystallization for natural rubber occurs at a lower strain compared to unfilled natural rubber, and the strain amplification effects were observed. The incorporation of graphene results in a faster strain-induced crystallization rate and a higher crystallinity compared to CNTs. The entanglement-bound rubber tube model was used to analyze the chain network structure and determine the network parameters of composites. The results show that the addition of graphene or CNTs has an influence on the molecular network structure and improves the contribution of entanglement to the conformational constraint, while graphene has a more marked effect than CNTs.

  13. Rubber particle proteins, HbREF and HbSRPP, show different interactions with model membranes.

    Science.gov (United States)

    Berthelot, Karine; Lecomte, Sophie; Estevez, Yannick; Zhendre, Vanessa; Henry, Sarah; Thévenot, Julie; Dufourc, Erick J; Alves, Isabel D; Peruch, Frédéric

    2014-01-01

    The biomembrane surrounding rubber particles from the hevea latex is well known for its content of numerous allergen proteins. HbREF (Hevb1) and HbSRPP (Hevb3) are major components, linked on rubber particles, and they have been shown to be involved in rubber synthesis or quality (mass regulation), but their exact function is still to be determined. In this study we highlighted the different modes of interactions of both recombinant proteins with various membrane models (lipid monolayers, liposomes or supported bilayers, and multilamellar vesicles) to mimic the latex particle membrane. We combined various biophysical methods (polarization-modulation-infrared reflection-adsorption spectroscopy (PM-IRRAS)/ellipsometry, attenuated-total reflectance Fourier-transform infrared (ATR-FTIR), solid-state nuclear magnetic resonance (NMR), plasmon waveguide resonance (PWR), fluorescence spectroscopy) to elucidate their interactions. Small rubber particle protein (SRPP) shows less affinity than rubber elongation factor (REF) for the membranes but displays a kind of "covering" effect on the lipid headgroups without disturbing the membrane integrity. Its structure is conserved in the presence of lipids. Contrarily, REF demonstrates higher membrane affinity with changes in its aggregation properties, the amyloid nature of REF, which we previously reported, is not favored in the presence of lipids. REF binds and inserts into membranes. The membrane integrity is highly perturbed, and we suspect that REF is even able to remove lipids from the membrane leading to the formation of mixed micelles. These two homologous proteins show affinity to all membrane models tested but neatly differ in their interacting features. This could imply differential roles on the surface of rubber particles. © 2013.

  14. Research and application of fuzzy subtractive clustering model on tensile strength of radiation vulcanization for nitrile-butadiene rubber

    International Nuclear Information System (INIS)

    Zuo Duwen; Wang Hong; Zhu Nankang

    2010-01-01

    By use of fuzzy subtractive clustering model, the relationship between tensile strength of radiation vulcanization of NBRL (Nitrile-butadiene rubber latex) and irradiation parameters have been investigated. The correlation coefficient was calculated to be 0.8222 in the comparison of experimental data to the predicted data. It was obvious that fuzzy model identification method is not only high precision with small computation, but also easy to be used. It can directly supply the evolution of tensile strength of NBR by fuzzy modeling method in radiation vulcanization process for nitrile-butadiene rubber. (authors)

  15. Enhancing mechanical and thermal properties of styrene-butadiene rubber/carboxylated acrylonitrile butadiene rubber blend by the usage of graphene oxide with diverse oxidation degrees

    Science.gov (United States)

    Xue, Xiaodong; Yin, Qing; Jia, Hongbing; Zhang, Xuming; Wen, Yanwei; Ji, Qingmin; Xu, Zhaodong

    2017-11-01

    Graphene oxide (GO) with various oxidation degrees were prepared through a modified Hummer's method by varying the dosage of oxidizing agent. Styrene-butadiene rubber (SBR)/carboxylated acrylonitrile butadiene rubber (XNBR)/GO nanocomposites were fabricated by aqueous-phase mixing of GO colloidal dispersion with SBR latex and a small loading of XNBR latex, followed by co-coagulation. Effects of GO oxidation degree on the morphology, structure, mechanical and thermal properties of nanocomposites were thoroughly investigated. The results showed that the mechanical strength of nanocomposites were enhanced with the increase of oxidation degree of GO. Especially, when the weight ratio of KMnO4 to graphite was 15/5, the tensile strength, tear strength and thermal conductivity of SBR/XNBR/GO filled with 3 phr (parts per hundred rubber) GO increased by 255.3%, 141.5% and 22.8%, respectively, compared to those of neat SBR/XNBR blend. In addition, the thermal stability and the solvent resistance of the nanocomposites were also improved significantly. This work suggested that GO with higher oxidation degree could effectively improve the properties of SBR/XNBR blend.

  16. A Lettuce (Lactuca sativa) Homolog of Human Nogo-B Receptor Interacts with cis-Prenyltransferase and Is Necessary for Natural Rubber Biosynthesis*

    Science.gov (United States)

    Qu, Yang; Chakrabarty, Romit; Tran, Hue T.; Kwon, Eun-Joo G.; Kwon, Moonhyuk; Nguyen, Trinh-Don; Ro, Dae-Kyun

    2015-01-01

    Natural rubber (cis-1,4-polyisoprene) is an indispensable biopolymer used to manufacture diverse consumer products. Although a major source of natural rubber is the rubber tree (Hevea brasiliensis), lettuce (Lactuca sativa) is also known to synthesize natural rubber. Here, we report that an unusual cis-prenyltransferase-like 2 (CPTL2) that lacks the conserved motifs of conventional cis-prenyltransferase is required for natural rubber biosynthesis in lettuce. CPTL2, identified from the lettuce rubber particle proteome, displays homology to a human NogoB receptor and is predominantly expressed in latex. Multiple transgenic lettuces expressing CPTL2-RNAi constructs showed that a decrease of CPTL2 transcripts (3–15% CPTL2 expression relative to controls) coincided with the reduction of natural rubber as low as 5%. We also identified a conventional cis-prenyltransferase 3 (CPT3), exclusively expressed in latex. In subcellular localization studies using fluorescent proteins, cytosolic CPT3 was relocalized to endoplasmic reticulum by co-occurrence of CPTL2 in tobacco and yeast at the log phase. Furthermore, yeast two-hybrid data showed that CPTL2 and CPT3 interact. Yeast microsomes containing CPTL2/CPT3 showed enhanced synthesis of short cis-polyisoprenes, but natural rubber could not be synthesized in vitro. Intriguingly, a homologous pair CPTL1/CPT1, which displays ubiquitous expressions in lettuce, showed a potent dolichol biosynthetic activity in vitro. Taken together, our data suggest that CPTL2 is a scaffolding protein that tethers CPT3 on endoplasmic reticulum and is necessary for natural rubber biosynthesis in planta, but yeast-expressed CPTL2 and CPT3 alone could not synthesize high molecular weight natural rubber in vitro. PMID:25477521

  17. A lettuce (Lactuca sativa) homolog of human Nogo-B receptor interacts with cis-prenyltransferase and is necessary for natural rubber biosynthesis.

    Science.gov (United States)

    Qu, Yang; Chakrabarty, Romit; Tran, Hue T; Kwon, Eun-Joo G; Kwon, Moonhyuk; Nguyen, Trinh-Don; Ro, Dae-Kyun

    2015-01-23

    Natural rubber (cis-1,4-polyisoprene) is an indispensable biopolymer used to manufacture diverse consumer products. Although a major source of natural rubber is the rubber tree (Hevea brasiliensis), lettuce (Lactuca sativa) is also known to synthesize natural rubber. Here, we report that an unusual cis-prenyltransferase-like 2 (CPTL2) that lacks the conserved motifs of conventional cis-prenyltransferase is required for natural rubber biosynthesis in lettuce. CPTL2, identified from the lettuce rubber particle proteome, displays homology to a human NogoB receptor and is predominantly expressed in latex. Multiple transgenic lettuces expressing CPTL2-RNAi constructs showed that a decrease of CPTL2 transcripts (3-15% CPTL2 expression relative to controls) coincided with the reduction of natural rubber as low as 5%. We also identified a conventional cis-prenyltransferase 3 (CPT3), exclusively expressed in latex. In subcellular localization studies using fluorescent proteins, cytosolic CPT3 was relocalized to endoplasmic reticulum by co-occurrence of CPTL2 in tobacco and yeast at the log phase. Furthermore, yeast two-hybrid data showed that CPTL2 and CPT3 interact. Yeast microsomes containing CPTL2/CPT3 showed enhanced synthesis of short cis-polyisoprenes, but natural rubber could not be synthesized in vitro. Intriguingly, a homologous pair CPTL1/CPT1, which displays ubiquitous expressions in lettuce, showed a potent dolichol biosynthetic activity in vitro. Taken together, our data suggest that CPTL2 is a scaffolding protein that tethers CPT3 on endoplasmic reticulum and is necessary for natural rubber biosynthesis in planta, but yeast-expressed CPTL2 and CPT3 alone could not synthesize high molecular weight natural rubber in vitro. © 2015 by The American Society for Biochemistry and Molecular Biology, Inc.

  18. Rubber molds for investment casting

    International Nuclear Information System (INIS)

    Sibtain, S.N.

    2011-01-01

    The main objective of the project is to investigate different types of molding rubbers used for investment casting. The level of shape complexity which can be achieved by using these rubber molds is also studied. It was almost impossible to make complex shapes molds using metal molds, in that cases rubber molds are very important because they arc flexible and give accurate and precise part dimensions. Turbine blades are hi-tech components with air-foil geometries that have close dimensional tolerances. They are made of super-alloys and manufactured by investment casting. The final blade profile depends upon the dimensional accuracy in each of the processing steps. In the present work experimental study for the production of high quality low cost castings of turbine blades using rubber molds and injected wax patterns is presented. Natural Rubber molds and wax patterns from these molds were made. Different types of molding rubbers were studied including natural rubber, silicone rubber and liquid silicone rubber. It was found that by using rubber molds we can make most complex shape with very less finishing required. The shrinkage was 12% as compared to original master pattern. Rubber molds were made using laboratory hot press. Three layers of rubber above and below the master pattern. After that vulcanization was done by giving temperature and pressure. (author)

  19. Characterization of the natural rubber from new rubber tree clones of PB 300 series; Caracterizacao da borracha natural dos novos clones de seringueira da serie PB 300

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Maycon J.; Spinelli, Rafaela O.; Moreno, Rogerio M.B.; Mattoso, Luiz H.C.; Martins, Maria Alice, E-mail: maria-alice.martins@embrapa.br [Embrapa Instrumentacao/LNNA, Sao Carlos, SP (Brazil); Scaloppi Junior, Erivaldo J. [Instituto Agronomico (IAC), Votuporanga, SP (Brazil). Centro de Seringueira e Sistemas Agroflorestais; Goncalves, Paulo de S. [Instituto Agronomico (IAC), Campinas, SP (Brazil)

    2015-07-01

    The natural rubber (NR) is present in more than 2500 species of plants, being the Hevea brasiliensis the most commercially exploited. It is a raw material of great importance to the Brazilian economy, but the country faces a production's deficit, having to import about 60% of its consumption. In this work , the latex obtained from rubber tree of new clones of PB series 300 (PB 311, PB 312, PB 314 , PB 326, PB 346 and PB 350 ) and RRIM 600 (control) were characterized by dry rubber content (DRC), total solids content, distribution of particle size, Zeta potential, thermogravimetry, differential scanning calorimetry, infrared in the spectroscopy (FTIR), nuclear magnetic resonance (NMR) and technological properties. The DRC values ranged from 33% to 40%, and total solids of 38% to 44%. All of the clones showed average particle diameter between 180.0 to 192.1 nm, excluding clones PB 326 and PB 346 with 150.0 nm and 157.9 nm, respectively. The NMR spectra and FTIR showed that the structure of the natural rubber from all clones studied is cis -1,4- polyisoprene. Natural rubber from the new clones showed good thermal stability up to 285 °C and glass transition temperature of -64 °C. (author)

  20. Super Lightweight, Metal Rubber Fabric for Extreme Space Environments, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — NanoSonic has fabricated revolutionary nanostructured, yet macroscale, multifunctional Metal RubberTM films via layer-by-layer, molecular self-assembly, which...

  1. The attitudes of dental interns to the use of the rubber dam at Riyadh dental colleges

    Directory of Open Access Journals (Sweden)

    Bander Mohammed Al-Abdulwahhab

    2012-01-01

    Full Text Available Background : The rubber dam is one of the best tools for tooth isolation and infection control in the dental field. Our aim is to evaluate the attitudes toward the use of rubber dams by dental interns in Riyadh Dental Colleges (RCsDP and determine the barriers to their use. Materials and Methods: A self-administered questionnaire was designed and used for data collection. 150 questionnaires were distributed by hand to the dental interns of RCsDP over a period of two weeks. Information sought included the attitudes toward and difficulties for the use of the rubber dam, the time needed to apply the rubber dam, and the patients′ allergic history of the rubber dam. Respondents were asked to state their preference on a five point Likert type scale ranging from "strongly dislike" to "strongly like". The information and data of the completed questionnaires were statistically analyzed using Mann-Whitney U test and Friedman test. Results: Of 150 questionnaires distributed, 150 were completed and returned (response rate = 100%. Of those, 46.7% were males and 53.3% were females. In general; (43.3%, interns strongly liked the use of the rubber dam and the rest (46.7% liked the use of the rubber dam. The majority of respondents liked to use rubber dam in direct restorations more than in indirect restorations and 46.7% strongly liked to use it in posterior teeth for composite restoration. Most dental interns felt that they would strongly like to use a rubber dam for endodontic treatment whether in posterior teeth (73.3% or anterior teeth (68.7%. 66.7% of interns asked their patients if they had an allergy to latex prior to the use of the rubber dam. Child behavior (mean rank about seven is the most important reason for not using rubber dam. The time is taken to apply the rubber dam was less than five minutes in most cases. Conclusion: Most dental interns prefer to use rubber dams in the general dental field and are enthusiastic to use it in future.

  2. Radiation Sterilization of Naturual Rubber Examination Gloves

    International Nuclear Information System (INIS)

    Jetawattana, S.; Na-Ranong, N.; Kajornchaiyakul, V.

    1998-01-01

    The sterilization dose setting by ISO 11137 method 1 was conducted for natural rubber examination gloves provided by a local factory. The suitable sterilization dose for an average product bioburden falls between 20 - 25 kilogray. Maximum dose of 25 or 50 kilogray results in no changes of tensile s and elongation at break. Samples of examination glove were irradiated using various doses between 10 - 50 kilogray. Analysis of soluble protein content using modified Lowry method was carried out and the results revealed that irradiation did not affect the decrement of soluble protein content in this case. However, thin film samples were prepared in laboratory and treated in the same procedure. The results were also the same. The results did not show any correlation. Two factors are possibly presumed : un consistency of samples and the irradiation of finished products could not affect those soluble proteins in rubber gloves

  3. Energy recycling of plastic and rubber wastes

    International Nuclear Information System (INIS)

    Hussain, R.

    2003-01-01

    Major areas for applications of plastics and rubbers are building and construction, packaging, transportation, automobiles, furniture, house wares, appliances, electrical and electronics. Approximately 20% of all the plastics produced are utilized by the building and construction industry/sup (1-3)/. Categories of polymers mostly used in the above industries include poly (vinyl chloride), polypropylene, polyethylene, polystyrene phenolics, acrylics and urethanes. Tyres and tubes are almost exclusively made up of rubbers. One third of total consumption of plastics finds applications, like films, bottles and packaging, in food-products that have a maximum life-span of two years, after which these find way to waste dumps. As the polymer industry in Pakistan is set to grow very rapidly in the near future the increase in utilization of plastic products in synchronous with the advent of computers and information technology. About 0.60 Kg per capita of waste generated daily in Lahore /(7.14)/ contains considerable quantity of plastics. (AB)

  4. Co-coagulation of the NBR latex and clay aqueous suspension: preparation and characterization

    International Nuclear Information System (INIS)

    Reis, Raquel S.; Brum, Elisson; Silva, Vanessa M.; Souza, Diego H.S.; Gomes, Ailton de S.; Nunes, Regina C.R.

    2009-01-01

    Blends of nitrile rubber (NBR) and sodium montmorillonite (MMT-Na) were prepared by co-coagulation of the NBR latex with aqueous suspension of clay. The content of MMT was varied from 0 to 7 phr and different mixtures were analyzed by X-ray diffraction, light scattering, gel content, thermogravimetric analysis and the oscillating disk rheometer. The different methods used indicated that there was formation of a structure interspersed in the mixtures studied, and that increasing the content MMT-Na enhances the values obtained. Rheological measurements on compositions with NBR showed the influence of clay on increasing the time of healing in terms of its content, as is the gel content and the thermal resistance. All results were compared to composition of NBR without MMT. (author)

  5. Analysis of the usage of rubberized asphalt in hot mix asphalt using Reclaimed Asphalt Pavement (RAP)

    Science.gov (United States)

    Dwidarma Nataadmadja, Adelia; Prahara, Eduardi; Sumbung, Pierre Christian

    2017-12-01

    There has been an increasing demand in using more environmentally friendly materials in pavement construction. One of the alternative materials that have been widely used is the Reclaimed Asphalt Pavement (RAP) aggregates. The RAP aggregates are derived from the crushed and screened pavement materials that contain asphalt and aggregates. This material is usually combined with natural aggregates and virgin asphalt binder to construct a new pavement. There have been numerous positive feedbacks in using this material although RAP aggregates also have certain weaknesses, such as questionable interaction between virgin and recycled materials and increased stiffness of RAP binder. Moreover, there has been a push on using rubber as an additive to asphalt binder to improve the welfare of rubber farmers. This research combines the usage of both latex and RAP as the ingredients to design hot mix asphalt (HMA) as latex could help in improving the flexibility of HMA and the interaction between the virgin and recycled materials. The main objective of this research is to find a suitable percentage of RAP aggregates to be used in HMA with certain percentage of latex as the binder additive.

  6. SNP identification from RNA sequencing and linkage map construction of rubber tree for anchoring the draft genome.

    Science.gov (United States)

    Shearman, Jeremy R; Sangsrakru, Duangjai; Jomchai, Nukoon; Ruang-Areerate, Panthita; Sonthirod, Chutima; Naktang, Chaiwat; Theerawattanasuk, Kanikar; Tragoonrung, Somvong; Tangphatsornruang, Sithichoke

    2015-01-01

    Hevea brasiliensis, or rubber tree, is an important crop species that accounts for the majority of natural latex production. The rubber tree nuclear genome consists of 18 chromosomes and is roughly 2.15 Gb. The current rubber tree reference genome assembly consists of 1,150,326 scaffolds ranging from 200 to 531,465 bp and totalling 1.1 Gb. Only 143 scaffolds, totalling 7.6 Mb, have been placed into linkage groups. We have performed RNA-seq on 6 varieties of rubber tree to identify SNPs and InDels and used this information to perform target sequence enrichment and high throughput sequencing to genotype a set of SNPs in 149 rubber tree offspring from a cross between RRIM 600 and RRII 105 rubber tree varieties. We used this information to generate a linkage map allowing for the anchoring of 24,424 contigs from 3,009 scaffolds, totalling 115 Mb or 10.4% of the published sequence, into 18 linkage groups. Each linkage group contains between 319 and 1367 SNPs, or 60 to 194 non-redundant marker positions, and ranges from 156 to 336 cM in length. This linkage map includes 20,143 of the 69,300 predicted genes from rubber tree and will be useful for mapping studies and improving the reference genome assembly.

  7. Cement-latex grouting mortar for cementing boreholes

    Energy Technology Data Exchange (ETDEWEB)

    Kateev, I S; Golyshkina, L A; Gorbunova, I V; Kurochkin, B M; Vakula, Ya V

    1980-01-01

    The need for the development of cement-latex grouting mortar for the purpose of separating strata when reinforcing boreholes at deposits in the Tatar Associated SSR is evaluated. Results of studies of the physical and mechanical properties of cement-latex grouting mortar systems (mortar plus brick) are presented. Formulas for preparing cement-latex grouting mortor are evaluated and results of industrial tests of such mortars shown.

  8. Thickness measuring instrument for rubber cord calender production

    International Nuclear Information System (INIS)

    Ye Songfeng

    1988-01-01

    The thickness measuring gauge has been used to measure the rubber film thickness on the coating of textile cord at tire four cord calenders. Combined with micro-computer it completes the automatic control system and acheives automatic thickness measurement and adjustment. The fundamentals, construction, specifications, characteristic and application results are described. Prominent economic benefit has been gained for tire production

  9. Rubber friction: The contribution from the area of real contact.

    Science.gov (United States)

    Tiwari, A; Miyashita, N; Espallargas, N; Persson, B N J

    2018-06-14

    There are two contributions to the friction force when a rubber block is sliding on a hard and rough substrate surface, namely, a contribution F ad = τ f A from the area of real contact A and a viscoelastic contribution F visc from the pulsating forces exerted by the substrate asperities on the rubber block. Here we present experimental results obtained at different sliding speeds and temperatures, and we show that the temperature dependency of the shear stress τ f , for temperatures above the rubber glass transition temperature T g , is weaker than that of the bulk viscoelastic modulus. The physical origin of τ f for T > T g is discussed, and we propose that its temperature dependency is determined by the rubber molecule segment mobility at the sliding interface, which is higher than in the bulk because of increased free-volume effect due to the short-wavelength surface roughness. This is consistent with the often observed reduction in the glass transition temperature in nanometer-thick surface layers of glassy polymers. For temperatures T contact regions and the contact area is determined by the rubber penetration hardness. For this case, we propose that the frictional shear stress is due to slip at the interface between the rubber and a transfer film adsorbed on the concrete surface.

  10. Aplication Of PGR IAA And Kinetin On Rubber Clones To Accelarate Mature Tapping

    Directory of Open Access Journals (Sweden)

    Try Koryati

    2017-09-01

    Full Text Available This study aims to determine the most appropriate concentration of IAA hormones Kinetin on rubber clones to accelerate the mature tapping. Experiments have been carried out in Karang Inong Plantation PTP N I Langsa East Aceh. This study is arranged in two factors of Nested Design. Clones factor is consisted of 5 level and IAA hormon Kinetin factor has 7 levels. The results showed that the concentration of IAA hormones Kinetin is different to each clone to accelerate mature tapping. Application of IAA hormone Kinetin significantly affect the parameters of girth bark thickness number of latex vessels latex vessel diameter leaf area and the amount of chlorophyll. Application of IAA 600ppm Kinetin 60 ppm H6 show the largest increase on the girth. Clone treatment is also has significant effect on all parameters but the largest girth found in clones PB 330 and IRR 5. Combination of Clones with IAA hormone Kinetin significantly affects the bark thickness the number of latex vessels and latex vessel diameter. Application of IAA 400 ppm Kinetin 60 ppm has no significant effect on girth but able to accelerate the mature tapping particularly for clones PB 330 and IRR5 K2H4 and K5H4 as indicated by girth size namely 48.15 cm and 48.20 cm respectively at planting age 46 months.

  11. Reinforcing styrene butadiene rubber with lignin-novolac epoxy resin networks

    Directory of Open Access Journals (Sweden)

    P. Yu

    2015-01-01

    Full Text Available In this study, lignin-novolac epoxy resin networks were fabricated in the styrene butadiene rubber (SBR matrix by combination of latex compounding and melt mixing. Firstly, SBR/lignin compounds were co-coagulated by SBR latex and lignin aqueous solution. Then the novolac epoxy resin (F51 was added in the SBR/lignin compounds by melt compounding method. F51 was directly cured by lignin via the ring-opening reaction of epoxy groups of F51 and OH groups (or COOH groups of lignin during the curing process of rubber compounds, as was particularly evident from Fourier transform infrared spectroscopy (FTIR studies and maximum torque of the curing analysis. The existence of lignin-F51 networks were also detected by scanning electron microscope (SEM and dynamic mechanical analysis (DMA. The structure of the SBR/lignin/F51 was also characterized by rubber process analyzer (RPA, thermogravimetric analysis (TGA and determination of crosslinking density. Due to rigid lignin-F51 networks achieved in SBR/lignin/F51 composites, it was found that the hardness, modulus, tear strength, crosslinking density, the temperature of 5 and 10% weight-loss were significantly enhanced with the loading of F51.

  12. Follow-up Study of Latex-allergic Health Care Workers in Japan

    Directory of Open Access Journals (Sweden)

    Akiko Yagami

    2006-01-01

    Conclusions: After avoiding latex products and following our educational suggestions, the patients' allergy symptoms had generally improved. This indicates that our countermeasures against latex allergy were largely successful.

  13. [Latex allergy in a paediatric hospital. Characteristics and risk factors].

    Science.gov (United States)

    Bailey, Michael; Norambuena, Ximena; Roizen, Gigia; Rodríguez, Jorge; Quezada, Arnoldo

    The prevalence of latex sensitisation varies according to the population studied. There are various risk factors that increase latex sensitisation, such as genetic risk, atopy, and multiple surgeries. To characterise patients referred to an Immunology Unit with suspected latex allergy, and to analyse their clinical features and risk factors. A retrospective, descriptive study was conducted on children suspected of latex allergy. Their medical records were reviewed in order to assess symptoms with contact or exposure to latex materials. Known risk factors to latex sensitisation, such as pathologies requiring repeated surgery (spina bifida, myelomeningocele, scoliosis and nephro-urological alterations), atopy (rhinitis, asthma, atopic dermatitis) were investigated. A prick test and/or specific IgE to latex were also performed. A multivariate logistic regression model was performed to find associations between symptoms triggered by exposure to latex with underlying diseases and other risk conditions. A total of 106 patients were enrolled in the study, of whom 50 were evaluable. At diagnosis 96% of patients were older than five years. Most of the risk factors described were observable in these patients, such as multiple surgeries, neurological and nephro-urological malformations, surgery before one year-old, and repeated bladder catheterisation. After latex exposure, mucous cutaneous manifestations were the most common (52%), followed by respiratory symptoms (36%). All patients were sensitised and allergic to latex. Latex allergy is a significant problem in children with risk factors. The results shown in this study raise important challenges for preventive measures and awareness. Copyright © 2016 Sociedad Chilena de Pediatría. Publicado por Elsevier España, S.L.U. All rights reserved.

  14. QENS investigation of filled rubbers

    CERN Document Server

    Triolo, A; Desmedt, A; Pieper, J K; Lo Celso, F; Triolo, R; Negroni, F; Arrighi, V; Qian, H; Frick, B

    2002-01-01

    The polymer segmental dynamics is investigated in a series of silica-filled rubbers. The presence of inert fillers in polymers greatly affects the mechanical and physical performance of the final materials. For example, silica has been proposed as a reinforcing agent of elastomers in tire production. Results from quasielastic neutron scattering and Dynamic Mechanical Thermal Analysis (DMTA) measurements are presented on styrene-ran-butadiene rubber filled with silica. A clear indication is obtained of the existence of a bimodal dynamics, which can be rationalized in terms of the relaxation of bulk rubber and the much slower relaxation of the rubber adsorbed on the filler surface. (orig.)

  15. Antimalarial Anthrone and Chromone from the Leaf Latex of Aloe ...

    African Journals Online (AJOL)

    In Ethiopian traditional medicine, the leaf latex of Aloe debranan Chrstian is used for the treatment of several diseases including malaria. In an ongoing search for effective, safe and cheap antimalarial agents from plants, the leaf latex of A. debrana was tested for its in vivo antimalarial activity, in a 4-day suppressive assay ...

  16. Antimicrobial activity of latex silver nanoparticles using Calotropis procera

    Directory of Open Access Journals (Sweden)

    Nadia Hussein Mohamed

    2014-11-01

    Conclusions: It can be concluded that serum latex of Calotropis procera was found to display strong potential for the synthesis of AgNPs as antimicrobial agents through rapid reduction of silver ions (Ag+ to Ag0. The green synthesized AgNPs were found to show higher antimicrobial efficacy than crude latex.

  17. Installing fonts in LaTeX a user's experience

    NARCIS (Netherlands)

    Hanssen, F.T.Y.

    2003-01-01

    This paper presents a user's experience with installing fonts for use in LaTeX. It will be shown that it is not hard to make a standard Type 1 font work, if you use modern font installation software for LaTeX. All the steps necessary to install the example fonts will be shown. The example fonts used

  18. Rapid latex agglutination test for the serodiagnosis of human brucellosis

    NARCIS (Netherlands)

    Abdoel, Theresia H.; Smits, Henk L.

    2007-01-01

    We developed and evaluated a user-friendly latex agglutination assay for the serodiagnosis of human brucellosis. The assay was obtained by coating colored latex beads with Brucella lipopolysaccharides and drying of the activated beads onto white agglutination cards. Individual cards were sealed in a

  19. Study on the properties of blend rubber prepared with grafted rubber and irradiated rubber by Gamma Rays

    International Nuclear Information System (INIS)

    Dafader, N. C.; Haque, M. E.; Islam, K. A.

    2004-05-01

    The blend rubbers were prepared by mixing γ-rays irradiated and monomer grafted rubbers. The monomers, methyl methacrylate (MMA) and styrene were used separately to prepare grafted rubber by exposure to radiation. The physico-chemical properties of the blend rubbers were evaluated. The tensile strength and elongation at break of the blend rubbers decrease whereas modulus at 500% elongation, swelling ratio and permanent set increase with the increased proportion of grafted rubber in the blend. The tear strength of the blend between irradiated and styrene grafted rubbers increases with the increased proportion of grafted rubber but that of the blend of irradiated and MMA grafted rubbers remains almost constant. The blend rubber could be used for special type of application like rubber thread, tube, catheter etc

  20. Experimental investigation of the effect of latex solid/water ratio on latex modified co-matrix mechanical properties

    Directory of Open Access Journals (Sweden)

    Ahmed M. Diab

    2013-03-01

    Full Text Available Numerous researches were performed on latex modified concretes and associated properties, however; some vital factors were not given attention in previous works. This study focus on new factor which significantly affects the properties of latex modified cement paste, mortar or concrete. This factor is termed as ‘latex solid/water ratio’ which is defined herein as the ratio of weight of solid latex to weight of total water content of cement composite including the water in latex itself. The effect of this factor on some properties of cement paste, mortar and concrete were experimentally evaluated. Properties of cement paste include the produced calcium hydroxide and ettringite content during hydration process, while those of cement mortar take account of absorption and effect of temperature on compressive strength. Furthermore, the effect of this factor on the compressive and flexural strengths, modulus of elasticity, water penetration depth and drying shrinkage of concrete were explored. Based on experimental evidences, and spite of using different cement contents, sources of latex, water–cement ratios and slump values, it can be generally concluded that the latex solid/water ratio is a dominant factor affecting different properties of latex modified mortars and concrete.

  1. Proceedings of the Second International Symposium on RVNRL (Radiation Vulcanisation of Natural Rubber Latex)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-31

    This book compiled the papers presented at this symposium. The papers discussed were categorized under i. preparation and properties of RVNRL, ii. characterisation and advantages of RVNRL, iii. scale up preparations and applications, iv. RVNRL pilot plant design and operation, and v. property improvement in RVNRL products,

  2. Proceedings of the Second International Symposium on RVNRL (Radiation Vulcanisation of Natural Rubber Latex)

    International Nuclear Information System (INIS)

    1996-01-01

    This book compiled the papers presented at this symposium. The papers discussed were categorized under i. preparation and properties of RVNRL, ii. characterisation and advantages of RVNRL, iii. scale up preparations and applications, iv. RVNRL pilot plant design and operation, and v. property improvement in RVNRL products,

  3. Decrease in the rate of sensitization and clinical allergy to natural rubber latex

    DEFF Research Database (Denmark)

    Blaabjerg, Michelle S B; Andersen, Klaus E; Bindslev-Jensen, Carsten

    2015-01-01

    patients prick tested for NRL at the Department of Dermatology and Allergy Centre, Odense University Hospital were included in this study (n = 8580). In NRL-sensitized patients, the clinical relevance was evaluated for NRL. Furthermore, concomitant positive prick test results for birch pollen were recorded.......5-0.6% in 2006-2013 (p history of reaction to oral intake of related fruits or vegetables. CONCLUSION: Our study showed a statistically significant decline in the number of patients...

  4. PROCESSED PRODUCTS OF THE HEVEIN PRECURSOR IN THE LATEX OF THE RUBBER TREE (HEVEN BRASILIENSIS)

    NARCIS (Netherlands)

    SOEDJANAATMADJA, UMS; SUBROTO, T; BEINTEMA, JJ

    1995-01-01

    The 20 kDa precursor of hevein and its C-terminal 14 kDa domain have been isolated. Sequence analysis of the C-terminal tryptic peptides of these proteins and comparison with the cDNA sequence indicate that they represent mature forms from which a C-terminal propeptide, possibly involved in vacuolar

  5. Nitrile rubber and carboxylated nitrile rubber resistance to soybean biodiesel

    Directory of Open Access Journals (Sweden)

    Felipe Nunes Linhares

    2018-03-01

    Full Text Available Abstract Biodiesel has been considered a suitable substitute for petroleum diesel, but their chemical composition differs greatly. For this reason, biodiesel interacts differently than petroleum diesel with various materials, including rubbers. Therefore, the resistance of some elastomers should be thoroughly evaluated, specifically those which are commonly used in automotive industry. Nitrile rubber (NBR is widely used to produce vehicular parts that are constantly in contact with fuels. This paper aimed to assess the resistance of carboxylated nitrile rubber (XNBR with 28% of acrylonitrile content to soybean biodiesel in comparison with non-carboxylated nitrile rubber samples, with high and medium acrylonitrile content (33 and 45%. NBR with medium acrylonitrile content showed little resistance to biodiesel. However, carboxylated nitrile rubber even with low acrylonitrile content had similar performance to NBR with high acrylonitrile content.

  6. Fracture behavior of rubber powder modified rubber blends applied for conveying belt top covers

    OpenAIRE

    Euchler, Eric; Stocek, Radek; Gehde, Michael; Bunzel, Jörg-Michael; Saal, Wolfgang; Kipscholl, Reinhold

    2016-01-01

    The aim of this study is concentrated on the experimental investigation of wear resistance of rubber powder modified rubber blends. Styrene-Butadiene-Rubber (SBR) blends applied for conveying belt top covers have been modified by ground rubber (rubber powder) based on SBR. We theoretically described the rubber wear mechanism due to loading conditions occurring at conveyor belts in the field, to simulate wear behavior of top cover rubber materials. An own developed testing equipment based on g...

  7. PROPERTIES TYRE TREAD RUBBERS DEPENDING ON PARTICULARITY OF RUBBER COMPOUND

    Directory of Open Access Journals (Sweden)

    Z. S. Shashok

    2014-01-01

    Full Text Available Summary. The results of studies of the elastomeric compositions based on natural rubber containing curatives different ratio "curing agent : vulcanization accelerator" listed in this article. Influence of the composition of the vulcanizing group on stress-strain and elastic- deformation properties of tire tread rubber was installed. It has been shown that a significant effect on thermo-oxidative aging of vulcanizates was the composition of the vulcanizing group. Results of studies resistance tread rubber to exposure to elevated temperatures were presented . Vulcanizates differing type and density by varying the cross-linking ratio of "curing agent : vulcanization accelerator" were obtained . Research results in the formation of rubber resistance and crack growth at different temperatures were presented. Revealed that the best education and resistance to tear propagation under normal conditions characterized by rubber ratio "curing agent : vulcanization accelerator" equal to 1.5:1. It has been established that a dynamic endurance study rubbers depends largely on the nature and concentration of the cross-linking cross-links and movable promote increase efficiency due to the grid and reduce the sulfidity rearrangement. During loading mode alternating deformations at elevated temperatures lability of polysulfide bonds negatively affects the performance of rubber, and the decisive role of providing strength and thermal cross-linking. It is shown that the performance of the spatial grid rubbers allow indirectly judge the dynamic vulcanizates endurance and predict performance rubbers at elevated temperatures under conditions of repeated cyclic deformation. Revealed that the vulcanizing system containing sulfur and vulcanization accelerator TBBS 1:2, promotes the formation of the optimal structure of vulcanized rubber , which provides the best resistance to repeated cyclic deformations in the operating temperatures of the tire.

  8. 77 FR 20357 - Polyethylene Terephthalate Film, Sheet, and Strip From the United Arab Emirates: Final Results of...

    Science.gov (United States)

    2012-04-04

    ... latex. Tracing and drafting film is also excluded. PET Film is classifiable under subheading 3920.62.00... on the Web at http://ia.ita.doc.gov/frn . The signed Decision Memorandum and the electronic versions...

  9. Crack Velocities in Natural Rubber.

    Science.gov (United States)

    1982-05-01

    vulcanized natural rubber (3). The surprisingly low value for natural rubber was attributed to highly anisotropic elastic behavior at high strains...Dr. R.L. Rabie Hercules Incorporated WX-2, MS-952 Alleghany Ballistic Lab Los Alamos National Lab. P.O. Box 210 P.O. Box 1663 Washington, D.C. 21502

  10. Alternative sources of natural rubber

    NARCIS (Netherlands)

    Mooibroek, H.; Cornish, K.

    2000-01-01

    Rubber (cis-1,4-polyisoprene) is one of the most important polymers naturally produced by plants because it is a strategic raw material used in more than 40,000 products, including more than 400 medical devices. The sole commercial source, at present, is natural rubber harvested from the Brazilian

  11. Evaluation of rubber seal products for gamma facilities

    International Nuclear Information System (INIS)

    Sobhy, M.S.; Shafy, M.A.; Shahin, F.

    2005-01-01

    Ageing behavior by employing the prolonged exposures of high-energy radiation such as gamma-rays on the physicomechanical properties of some rubber seal products are studied. The proposed binary-rubber blends, SBR/NBR, EPDM/NBR and EPDM/EPM. have overcome their problem of inhomogeneity and incompatibility between the two rubber phases. Such enhancements are acquired by either the replacement of part of NBR by SBR during mastication, or the incorporation of maleic anhydride. Results show that the EPDM/EPM rubber blend has possessed the radiation resistance property towards the deterioration due to higher gamma-irradiation dose. The SEM images have c early observed the role of the used antioxidant, where a thin film is usually produced, degraded; with the appearance of surface cracks, and repaired with further gamma-irradiation up to high doses. Such enhancement is necessary for the definition of the requirements to be put on rubber seal materials. Finally, these products ought to assure the quality control in production and evaluate their application suitability that may employ in the pneumatic system in gamma facility

  12. Robotically enhanced rubber hand illusion.

    Science.gov (United States)

    Arata, Jumpei; Hattori, Masashi; Ichikawa, Shohei; Sakaguchi, Masamichi

    2014-01-01

    The rubber hand illusion is a well-known multisensory illusion. In brief, watching a rubber hand being stroked by a paintbrush while one's own unseen hand is synchronously stroked causes the rubber hand to be attributed to one's own body and to "feel like it's my hand." The rubber hand illusion is thought to be triggered by the synchronized tactile stimulation of both the subject's hand and the fake hand. To extend the conventional rubber hand illusion, we introduce robotic technology in the form of a master-slave telemanipulator. The developed one degree-of-freedom master-slave system consists of an exoskeleton master equipped with an optical encoder that is worn on the subject's index finger and a motor-actuated index finger on the rubber hand, which allows the subject to perform unilateral telemanipulation. The moving rubber hand illusion has been studied by several researchers in the past with mechanically connected rigs between the subject's body and the fake limb. The robotic instruments let us investigate the moving rubber hand illusion with less constraints, thus behaving closer to the classic rubber hand illusion. In addition, the temporal delay between the body and the fake limb can be precisely manipulated. The experimental results revealed that the robotic instruments significantly enhance the rubber hand illusion. The time delay is significantly correlated with the effect of the multisensory illusion, and the effect significantly decreased at time delays over 100 ms. These findings can potentially contribute to the investigations of neural mechanisms in the field of neuroscience and of master-slave systems in the field of robotics.

  13. The preparation of RVNRL using Malaysian-produced latexes

    International Nuclear Information System (INIS)

    Zin, W.M. bin W.; Mohid, N. bte; Hasan, J. bin; Noor, W.K.A. bte W.M.; Jaafar, Zulkifli

    1993-01-01

    This research project was carried out using latexes supplied by three of the suppliers in Malaysia. From the results of studies carried out in search of the best sensitiser for RVNRL preparation, the use of n-butyl acrylate (n-BA) as a sensitiser gave the most promising results. However, its use as a sensitiser is not universal to all latexes available in the country. The problem was overcome by using different formulations for different latexes. For the latex supplied by Golden Hope (Hytex), a combination of sensitisers i.e. n-BA plus 2-ethyl hexyl acrylate (2-EHA) with a 10% potassium hydroxide solution as the stabilizer, was required. Latex supplied by MARDEC (Matex), seemed to need only n-BA as the sensitiser. However, a stabilizer was still required and the use of a 10% KOH solution was found to be suitable. A large range of stabilizers and sensitisers were applicable to Guthrie latex. The use of n-BA as the sensitiser and potassium laurylic acid as the stabilizer seemed the most favourable formulation. All the results are discussed in the form of a correlation between dose and the tensile properties of RVNRL vulcanizates, equilibrium swelling ratio and standing time of the latex formulation. (author)

  14. The Synthesis and Modification of Nanosized Clickable Latex Particles

    KAUST Repository

    Almahdali, Sarah

    2013-05-01

    This research aims to add to the current knowledge available for miniemulsion polymerization reactions and to use this knowledge to synthesize multifunctional nanosized latex particles that have the potential to be used in catalysis. The physical properties of the latex can be adjusted to suit various environments due to the multiple functional groups present. For this research, styrene, pentafluorostyrene, azidomethyl styrene, pentafluorostyrene with azidomethyl styrene and pentafluorostyrene with styrene latexes were produced, and analyzed by dynamic light scattering. The latexes were synthesized using a miniemulsion polymerization technique found through this research. Potassium oleate and potassium 1,1,2,2,3,3,4,4-nonafluorobutane-1-sulfonate were used as surfactants during the miniemulsion polymerization reaction to synthesize pentafluorostyrene with azidomethyl styrene latex. Transmission electron microscopy data and dynamic light scattering data have been collected to analyze the structure of this latex, and it has been synthesized using a number of conditions, differing in reaction time, surfactant amount and sonication methods. We have also improved the solubility of the latex through a copper(I) catalyzed 1,3-dipolar azide-alkyne reaction, by clicking (polyethylene glycol)5000 onto the azide functional groups.

  15. Size effects of latex nanomaterials on lung inflammation in mice

    International Nuclear Information System (INIS)

    Inoue, Ken-ichiro; Takano, Hirohisa; Yanagisawa, Rie; Koike, Eiko; Shimada, Akinori

    2009-01-01

    Effects of nano-sized materials (nanomaterials) on sensitive population have not been well elucidated. This study examined the effects of pulmonary exposure to (latex) nanomaterials on lung inflammation related to lipopolysaccharide (LPS) or allergen in mice, especially in terms of their size-dependency. In protocol 1, ICR male mice were divided into 8 experimental groups that intratracheally received a single exposure to vehicle, latex nanomaterials (250 μg/animal) with three sizes (25, 50, and 100 nm), LPS (75 μg/animal), or LPS plus latex nanomaterials. In protocol 2, ICR male mice were divided into 8 experimental groups that intratracheally received repeated exposure to vehicle, latex nanomaterials (100 μg/animal), allergen (ovalbumin: OVA; 1 μg/animal), or allergen plus latex nanomaterials. In protocol 1, latex nanomaterials with all sizes exacerbated lung inflammation elicited by LPS, showing an overall trend of amplified lung expressions of proinflammatory cytokines. Furthermore, LPS plus nanomaterials, especially with size less than 50 nm, significantly elevated circulatory levels of fibrinogen, macrophage chemoattractant protein-1, and keratinocyte-derived chemoattractant, and von Willebrand factor as compared with LPS alone. The enhancement tended overall to be greater with the smaller nanomaterials than with the larger ones. In protocol 2, latex nanomaterials with all sizes did not significantly enhance the pathophysiology of allergic asthma, characterized by eosinophilic lung inflammation and Igs production, although latex nanomaterials with less than 50 nm significantly induced/enhanced neutrophilic lung inflammation. These results suggest that latex nanomaterials differentially affect two types of (innate and adaptive immunity-dominant) lung inflammation

  16. Nano-reinforcement of tire rubbers: silica-technology for natural rubber : exploring the infuence of non-rubber constituents on the natural rubber-silica system

    NARCIS (Netherlands)

    Sarkawi, S.S.

    2013-01-01

    Natural rubber is a renewable resource material with outstanding properties which offers significant advantages over its counterparts, the fossil-resource synthetic rubbers. In fact, a natural rubber tree is an efficient carbon dioxide sequester. Since natural rubber is a natural product, it is

  17. Solubility Study of Curatives in Various Rubbers

    NARCIS (Netherlands)

    Guo, R.; Talma, Auke; Datta, Rabin; Dierkes, Wilma K.; Noordermeer, Jacobus W.M.

    2008-01-01

    The previous works on solubility of curatives in rubbers were mainly carried out in natural rubber. Not too much information available on dissimilar rubbers and this is important because most of the compounds today are blends of dissimilar rubbers. Although solubility can be expected to certain

  18. Isolation and characterization of latex-specific promoters from Papaver somniferum L.

    OpenAIRE

    Raymond, Michelle Jean

    2004-01-01

    The pharmacologically important alkaloids morphine and codeine are found in latex of opium poppy (Papaver somniferum). Latex is harbored in laticifers, a specialized vascular cell-type. Isolation and characterization of latex-specific genes may provide a useful tool to metabolically engineer increased alkaloid production. Previous research in the Nessler laboratory identified genes that exhibit latex-specific gene expression. Latex-specific genes were an 2-oxoglutarate-dioxygense (DIOX), ...

  19. Comparative study on plant latex particles and latex coagulation in Ficus benjamina, Campanula glomerata and three Euphorbia species.

    Directory of Open Access Journals (Sweden)

    Georg Bauer

    Full Text Available Among latex-producing plants, mainly the latex of Hevea brasiliensis has been studied in detail so far, while comprehensive comparative studies of latex coagulation mechanisms among the more than 20,000 latex-bearing plant species are lacking. In order to give new insights into the potential variety of coagulation mechanisms, the untreated natural latices of five latex-bearing plants from the families Euphorbiaceae, Moraceae and Campanulaceae were visualised using Cryo-SEM and their particle size compared using the laser diffraction method. Additionally, the laticifers of these plants species were examined in planta via Cryo-SEM. Similar latex particle sizes and shape were found in Ficus benjamina and Hevea brasiliensis. Hence, and due to other similarities, we hypothesize comparable, mainly chemical, coagulation mechanisms in these two species, whereas a physical coagulation mechanism is proposed for the latex of Euphorbia spp. The latter mechanism is based on the huge amount of densely packed particles that after evaporation of water build a large surface area, which accelerates the coagulation procedure.

  20. Thermoresponsive latexes for fragrance encapsulation and release.

    Science.gov (United States)

    Popadyuk, N; Popadyuk, A; Kohut, A; Voronov, A

    2016-04-01

    To synthesize cross-linked latex particles protecting the encapsulated fragrance at ambient temperatures and facilitating the release of cargo at the temperature of the surface of the skin that varies in different regions of the body between 33.5 and 36.9°C. Poly(stearyl acrylate) (PSA), a polymer with long crystallizable alkyl side chains (undergoes order-disorder transitions at 45°C), was chosen as the main component of the polymer particles. As a result, new thermoresponsive polymer particles for fragrance encapsulation were synthesized and characterized, including assessing the performance of particles in triggered release by elevated temperature. To obtain network domains of various crystallinity, stearyl acrylate was copolymerized with dipropylene glycol acrylate caprylate (DGAC) (comonomer) in the presence of a dipropylene glycol diacrylate sebacate (cross-linker) using the miniemulsion process. Comonomers and a cross-linker were mixed directly in a fragrance during polymerization. Fragrance release was evaluated at 25, 31, 35 and 39°C to demonstrate a new material potential in personal/health care skin-related applications. Particles protect the fragrance from evaporation at 25°C. The fragrance release rate gradually increases at 31, 35 and 39°C. Two slopes were found on release plots. The first slope corresponds to a rapid fragrance release. The second slope indicates a subsequent reduction in the release rate. Crystalline-to-amorphous transition of PSA triggers the release of fragrances from cross-linked latex particles at elevated temperatures. The presence of the encapsulated fragrance, as well as the inclusion of amorphous fragments in the polymer network, reduces the particle crystallinity and enhances the release. Release profiles can be tuned by temperature and controlled by the amount of loaded fragrance and the ratio of comonomers in the feed mixture. © 2015 Society of Cosmetic Scientists and the Société Française de Cosmétologie.

  1. Blends of natural rubber and polyurethane lattices studied by solid-state NMR

    International Nuclear Information System (INIS)

    Ricardo, Nagila M.P.S.; Franca, Francisco C.F. de; Price, Colin; Heatley, Frank

    2001-01-01

    Molecular mixing in films formed from a mixture of a polyurethane and natural rubber lattices has been studied using 1 H and 13 C solid-state NMR. The techniques employed include 1 H relaxation measurements, and 13 C cross-polarisation and direct excitation methods. The spectra of the blends were essentially a weighted superposition of the spectra of the individual components, indicating that the polyurethane and rubber remained phase-separated in large domains. (author)

  2. Prediction of direct and indirect genetic gains and genotypic correlations in rubber tree progenies

    Directory of Open Access Journals (Sweden)

    Cecília Khusala Verardi

    2011-09-01

    Full Text Available The objective of this work was to estimate the genetic parameters, genotypic and phenotypic correlations, and direct and indirect genetic gains among and within rubber tree (Hevea brasiliensis progenies. The experiment was set up at the Municipality of Jaú, SP, Brazil. A randomized complete block design was used, with 22 treatments (progenies, 6 replicates, and 10 plants per plot at a spacing of 3x3 m. Three‑year‑old progenies were assessed for girth, rubber yield, and bark thickness by direct and indirect gains and genotypic correlations. The number of latex vessel rings showed the best correlations, correlating positively and significantly with girth and bark thickness. Selection gains among progenies were greater than within progeny for all the variables analyzed. Total gains obtained were high, especially for girth increase and rubber yield, which were 93.38 and 105.95%, respectively. Young progeny selection can maximize the expected genetic gains, reducing the rubber tree selection cycle.

  3. Cryo-SEM studies of latex/ceramic nanoparticle coating microstructure development.

    Science.gov (United States)

    Luo, Hui; Scriven, L E; Francis, Lorraine F

    2007-12-15

    Cryogenic scanning electron microscopy (cryo-SEM) was used to investigate microstructure development of composite coatings prepared from dispersions of antimony-doped tin oxide (ATO) nanoparticles (approximately 30 nm) or indium tin oxide (ITO) nanoparticles (approximately 40 nm) and latex particles (polydisperse, D(v): approximately 300 nm). Cryo-SEM images of ATO/latex dispersions as-frozen show small clusters of ATO and individual latex particles homogeneously distribute in a frozen water matrix. In contrast, cryo-SEM images of ITO/latex dispersions as-frozen show ITO particles adsorb onto latex particle surfaces. Electrostatic repulsion between negatively charged ATO and negatively charged latex particles stabilizes the ATO/latex dispersion, whereas in ITO/latex dispersion, positively charged ITO particles are attracted onto surfaces of negatively charged latex particles. These results are consistent with calculations of interaction potentials from past research. Cryo-SEM images of frozen and fractured coatings reveal that both ceramic nanoparticles and latex become more concentrated as drying proceeds; larger latex particles consolidate with ceramic nanoparticles in the interstitial spaces. With more drying, compaction flattens the latex-latex particle contacts and shrinks the voids between them. Thus, ceramic nanoparticles are forced to pack closely in the interstitial spaces, forming an interconnected network. Finally, latex particles partially coalesce at their flattened contacts, thereby yielding a coherent coating. The research reveals how nanoparticles segregate and interconnect among latex particles during drying.

  4. Co-coagulation of the NBR latex and clay aqueous suspension: preparation and characterization;Co-coagulacao de latex de NBR e suspensao aquosa de argila: preparacao e caracterizacao

    Energy Technology Data Exchange (ETDEWEB)

    Reis, Raquel S.; Brum, Elisson; Silva, Vanessa M. [Nitriflex S/A Industria e Comercio, Rio de Janeiro, RJ (Brazil); Souza, Diego H.S.; Gomes, Ailton de S.; Nunes, Regina C.R., E-mail: rcnunes@ima.ufrj.b [Universidade Federal do Rio de Janeiro (IMA/UFRJ), RJ (Brazil). Inst. de Macromoleculas Profa. Eloisa Mano

    2009-07-01

    Blends of nitrile rubber (NBR) and sodium montmorillonite (MMT-Na) were prepared by co-coagulation of the NBR latex with aqueous suspension of clay. The content of MMT was varied from 0 to 7 phr and different mixtures were analyzed by X-ray diffraction, light scattering, gel content, thermogravimetric analysis and the oscillating disk rheometer. The different methods used indicated that there was formation of a structure interspersed in the mixtures studied, and that increasing the content MMT-Na enhances the values obtained. Rheological measurements on compositions with NBR showed the influence of clay on increasing the time of healing in terms of its content, as is the gel content and the thermal resistance. All results were compared to composition of NBR without MMT. (author)

  5. The Synthesis and Modification of Nanosized Clickable Latex Particles

    KAUST Repository

    Almahdali, Sarah

    2013-01-01

    This research aims to add to the current knowledge available for miniemulsion polymerization reactions and to use this knowledge to synthesize multifunctional nanosized latex particles that have the potential to be used in catalysis. The physical

  6. PS-HEMA latex fractionation by sedimentation and colloidal crystallization

    Directory of Open Access Journals (Sweden)

    Cardoso André H.

    1999-01-01

    Full Text Available A poly(styrene-co-hydroxyethylmethacrylate latex underwent sedimentation under gravity followed by an spontaneous and extensive colloidal crystallization. It was then fractionated in three visually distinguishable layers. Latex aliquots layers were sampled at different heigths and the particles were characterized by PCS, microelectrophoresis, infrared spectra and analytical electron microscopy. The major fraction was opalescent and contained the colloidal crystals settled in the bottom of the liquid. Two other latex fractions were obtained, which differed in their chemical compositions, particle sizes and topochemical features from the self-arraying particles. Macrocrystallization of the fractionated latex yielded high quality crystals with a low frequency of defects, which confirms that particle chemical homogeneity is an important factor for particle self-arraying.

  7. Assessment of adverse reactions to latex gloves use among nurses ...

    African Journals Online (AJOL)

    ... to latex is a common problem among nurses and other health care workers. ... There was significant association between family history and occurrence of ... These effects may vary in severity from skin problems to anaphylactic shock.

  8. Nitrile rubber and carboxylated nitrile rubber resistance to soybean biodiesel

    OpenAIRE

    Felipe Nunes Linhares; Cléverson Fernandes Senra Gabriel; Ana Maria Furtado de Sousa; Marcia Christina Amorim Moreira Leite; Cristina Russi Guimarães Furtado

    2018-01-01

    Abstract Biodiesel has been considered a suitable substitute for petroleum diesel, but their chemical composition differs greatly. For this reason, biodiesel interacts differently than petroleum diesel with various materials, including rubbers. Therefore, the resistance of some elastomers should be thoroughly evaluated, specifically those which are commonly used in automotive industry. Nitrile rubber (NBR) is widely used to produce vehicular parts that are constantly in contact with fuels. T...

  9. Synthesis and characterization of novel polyacid-stabilized latexes.

    Science.gov (United States)

    Yang, Pengcheng; Armes, S P

    2012-09-18

    A series of novel polyacid macromonomers based on 2-hydroxypropyl methacrylate (HPMA) were prepared by atom transfer radical polymerization (ATRP) via a two-step route. First, a range of well-defined PHPMA homopolymer precursors were synthesized by ATRP using a tertiary amine-functionalized initiator, 2-(dimethylamino)ethyl-2-bromoisobutyrylamide, and a CuCl/2, 2'-bipyridine (bpy) catalyst in alcoholic media at 50 °C. ATRP polymerizations were relatively slow and poorly controlled in pure isopropanol (IPA), especially when targeting higher degrees of polymerization (DP > 30). Improved control was achieved by addition of water: low polydispersity (M(w)/M(n) propyl methacrylate) (PSPMA) macromonomers by quaternizing the tertiary amine end-group with excess 4-vinylbenzyl chloride, followed by esterification of the pendent hydroxyl groups using excess succinic anhydride at 20 °C. These polyacid macromonomers were evaluated as reactive steric stabilizers for polystyrene latex synthesis under either aqueous emulsion polymerization or alcoholic dispersion polymerization conditions. Near-monodisperse polystyrene latexes were obtained via aqueous emulsion polymerization using 10 wt % PSPMA macromonomer (with respect to styrene monomer) with various initiators as evidenced by scanning electron microscopy, disk centrifuge photosedimentometry and light scattering studies. PSPMA macromomer concentrations as low as 1.0 wt % also produced near-monodisperse latexes, suggesting that these PSPMA macromonomers are highly effective stabilizers. Alcoholic dispersion polymerization of styrene conducted in various ethanol/water mixtures with 10 wt % PSPMA(50) macromonomer produced relatively large near-monodisperse latexes. Increasing the water content in such formulations led to smaller latexes, as expected. Control experiments conducted with 10 wt % PSPMA(50) homopolymer produced relatively large polydisperse latexes via emulsion polymerization and only macroscopic precipitates via

  10. Radioactive iodine (125I) labeling of latex particles

    International Nuclear Information System (INIS)

    Parikh, G.C.; Ho, C.K.

    1977-01-01

    The invention disclosed in this application is directed towards developing a radioiodination method which is applicable to the labeling of 2.02 micrometer (μm) and 0.37 micrometer (μm) diameter polyvinyltoluene latex particles that have been used as an immunoadsorbent. More particularly the overall method includes using an oxidation-reduction chemical reaction for tagging latex particles. Two methods are described. One, the hydrochloric acid method; and two, the nitric acid method

  11. Ultraviolet curing of epoxidised palm oil acrylate (Epola) and liquid epoxidised natural rubber acrylate (Lenra) on rubberwood substrates-a preliminary study

    International Nuclear Information System (INIS)

    Mohd Hilmi bin Mahmood; Dahlan bin Hj Mohd; Abdul Ghani bin Harun; Ahmad Shakri bin Mat Seman; Azizol bin Abdul Kadir

    1992-01-01

    Palm oil based and natural rubber based formulations were cured by ultraviolet (UV) radiation using rubberwood as a substrate. The appearance properties of the cured films were assessed and subjected to mechanical testing. Both formulations gave good finish films. Mechanical tests show that both films can resist abrasion, heat as well as chemical. Overall results show that natural rubber based formulation is superior than palm oil based

  12. The Possibilities to use Euphorbia Tirucalli as an Energy and a Rubber Crop

    Directory of Open Access Journals (Sweden)

    Patrick Van Damme

    1990-02-01

    Full Text Available Euphorbia tirucalli has been used as a source for natural rubber at different times in history, especially in southern Africa. The latex resin content is too high to guarantee a good quality product and economic production has never taken off as some had hoped. The fact that the plant is very well adapted to arid and semi arid conditions and can be grown on marginal waste lands makes it a potential energy crop which can be turned into biogas without too much investment in costly technology. The first results obtained in the laboratory and in field conditions (Senegal are very promising. The latex contains a number of interesting triterpenes which have a very high energy content and could be used in fuel production. Most of these applications have been tested or used in Africa and can offer long-term solutions for old problems, particularly in the case of renewable energy through biomass fermentation. KEY WORDS: rubber, biomass, biogas, triterpenes, energy crop

  13. Immune response modulation by curcumin in a latex allergy model

    Directory of Open Access Journals (Sweden)

    Raju Raghavan

    2007-01-01

    Full Text Available Abstract Background There has been a worldwide increase in allergy and asthma over the last few decades, particularly in industrially developed nations. This resulted in a renewed interest to understand the pathogenesis of allergy in recent years. The progress made in the pathogenesis of allergic disease has led to the exploration of novel alternative therapies, which include herbal medicines as well. Curcumin, present in turmeric, a frequently used spice in Asia has been shown to have anti-allergic and inflammatory potential. Methods We used a murine model of latex allergy to investigate the role of curcumin as an immunomodulator. BALB/c mice were exposed to latex allergens and developed latex allergy with a Th2 type of immune response. These animals were treated with curcumin and the immunological and inflammatory responses were evaluated. Results Animals exposed to latex showed enhanced serum IgE, latex specific IgG1, IL-4, IL-5, IL-13, eosinophils and inflammation in the lungs. Intragastric treatment of latex-sensitized mice with curcumin demonstrated a diminished Th2 response with a concurrent reduction in lung inflammation. Eosinophilia in curcumin-treated mice was markedly reduced, co-stimulatory molecule expression (CD80, CD86, and OX40L on antigen-presenting cells was decreased, and expression of MMP-9, OAT, and TSLP genes was also attenuated. Conclusion These results suggest that curcumin has potential therapeutic value for controlling allergic responses resulting from exposure to allergens.

  14. The Cyclization of natural rubber

    International Nuclear Information System (INIS)

    Mirzataheri, M.

    2000-01-01

    The effect of solvent, temperature, time, weight percent of catalyst on the rate and mechanism of cyclization of natural rubber was studied in toluene and xylene solutions having tin tetra chloride catalyst (SnCl 4 ). Iodo metric titration show, with 8% SnCl 4 (based on polymer weight) cyclization occurs, leaving 27.4% of the total unsaturation. Infrared spectra of cyclized natural rubber show decreased absorption intensity at 840 and 780 cm -1 which are characteristic bands of the linear polymer and the appearance of absorption band at 890 cm -1 as cycles were formed. By using this chemical modification, natural rubber is transformed into a resinous thermoplastic, hard, non rubbery cyclized material with much less unsaturation than the original rubber, which could find commercial applications ad adhesives, printing inks, industrial and ship paints

  15. Effects of Thermal and Humidity Aging on the Interfacial Adhesion of Polyketone Fiber Reinforced Natural Rubber Composites

    Directory of Open Access Journals (Sweden)

    Han Ki Lee

    2016-01-01

    Full Text Available Polyketone fiber is considered as a reinforcement of the mechanical rubber goods (MRG such as tires, automobile hoses, and belts because of its high strength and modulus. In order to apply it to those purposes, the high adhesion of fiber/rubber interface and good sustainability to aging conditions are very important. In this study, polyketone fiber reinforced natural rubber composites were prepared and they were subjected to thermal and humidity aging, to assess the changes of the interfacial adhesion and material properties. Also, the effect of adhesive primer treatment, based on the resorcinol formaldehyde resin and latex (RFL, of polyketone fiber for high interfacial adhesion was evaluated. Morphological and property changes of the rubber composites were analyzed by using various instrumental analyses. As a result, the rubber composite was aged largely by thermal aging at high temperature rather than humidity aging condition. Interfacial adhesion of the polyketone/NR composites was improved by the primer treatment and its effect was maintained in aging conditions.

  16. Latex constituents from Calotropis procera (R. Br. display toxicity upon egg hatching and larvae of Aedes aegypti (Linn.

    Directory of Open Access Journals (Sweden)

    Márcio Viana Ramos

    2006-08-01

    Full Text Available Calotropis procera R. Br. (Asclepiadaceae is a well-known medicinal plant with leaves, roots, and bark being exploited by popular medicine to fight many human and animal diseases. This work deals with the fractionation of the crude latex produced by the green parts of the plant and aims to evaluate its toxic effects upon egg hatching and larval development of Aedes aegypti. The whole latex was shown to cause 100% mortality of 3rd instars within 5 min. It was fractionated into water-soluble dialyzable (DF and non-dialyzable (NDF rubber-free materials. Both fractions were partially effective to prevent egg hatching and most of individuals growing under experimental conditions died before reaching 2nd instars or stayed in 1st instars. Besides, the fractions were very toxic to 3rd instars causing 100% mortality within 24 h. When both fractions were submitted to heat-treatment the toxic effects were diminished considerably suggesting low thermostability of the toxic compounds. Polyacrylamide gel electrophoresis of both fractions and their newly fractionated peaks obtained through ion exchange chromatography or desalting attested the presence of proteins in both materials. When submitted to protease digestion prior to larvicidal assays NDF lost most of its toxicity but DF was still strongly active. It may be possible that the highly toxic effects of the whole latex from C. procera upon egg hatching and larvae development should be at least in part due to its protein content found in NDF. However the toxicity seems also to involve non protein molecules present in DF.

  17. Tribology Aspect of Rubber Shock Absorbers Development

    Directory of Open Access Journals (Sweden)

    M. Banić

    2013-09-01

    Full Text Available Rubber is a very flexible material with many desirable properties Which enable its broad use in engineering practice. Rubber or rubber-metal springs are widely used as anti-vibration or anti-shock components in technical systems. Rubber-metal springs are usually realized as a bonded assembly, however especially in shock absorbers, it is possible to realize free contacts between rubber and metal parts. In previous research it authors was observed that friction between rubber and metal in such case have a significant influence on the damping characteristics of shock absorber. This paper analyzes the development process of rubber or rubber-metal shock absorbers realized free contacts between the constitutive parts, starting from the design, construction, testing and operation, with special emphasis on the development of rubber-metal springs for the buffing and draw gear of railway vehicles.

  18. Synthesis of polymer hybrid latex poly(methyl methacrylate-co-butyl acrylate) with organo montmorillonite via miniemulsion polymerization method for barrier paper

    Science.gov (United States)

    Chanra, J.; Budianto, E.; Soegijono, B.

    2018-03-01

    Hybrid polymer latex based on combination of organic-inorganic materials, poly(methyl methacrylate-co-butyl acrylate) (PMMBA) and organo-montmorillonite (OMMT) were synthesized via miniemulsion polymerization technique. Modification of montmorillonite (MMT) through the incorporation of myristyltrimethylammonium bromide (MTAB) into the clay’s interlayer spaces were investigated by Small-Angle X-ray Scattering (SAXS), Fourier Transform Infrared Spectroscopy (FTIR), Thermogravimetric Analysis (TGA) and Transmission Electron Microscopy (TEM). Barrier property and thermal stability of polymer latex film sample were investigated through its Water Vapor Transmission Rate (WVTR) and Thermogravimetric Analysis (TGA). The results indicated that addition of OMMT as filler in PMMBA increased the barrier property and thermal stability of the latex film. Addition of 8.0% (wt) OMMT increased the barrier property and thermal stability. Miniemusion polymerization process with higher addition (>8.0 wt%) of OMMT resulting in high latex viscosity, particle size, and high amount of coagulum. The utilization of this hybrid polymer could benefits paper and board industries to produce high quality barrier paper for food packaging.

  19. Rubber mixing process and its relationship with bound rubber and crosslink density

    Science.gov (United States)

    Hasan, A.; Rochmadi; Sulistyo, H.; Honggokusumo, S.

    2017-06-01

    This research studied the relationship between bound rubber and crosslink density based on rubber mixing process. Bound rubber was obtained after natural rubber was masticated and mixed with rubber chemicals and filler while crosslink density was collected after rubber compound was vulcanized. Four methods are used and each method refers to four ways of incorporating carbon black during mixing. The first method, after rubber was masticated for 5 minutes, the addition of rubber chemicals and filler was done simultaneously. Rubber was masticated for 1 minute and continued mixing of rubber chemicals and filler where mixing was different from first method. This was the second method. The third method was the same as the second method but the filler used N 660 while in the second method N 330. The last method is not the same as the first and second, the rubber is only masticated for 3 minutes and then mixed with filler and followed by rubber chemicals sequentially. The results showed that bound rubber and crosslink density were influenced by mixing and mastication process. Bound rubber dropped and crosslink density was relatively stable in the first three mixing methods for increasing carbon black at the beginning of the mixing process. Bound rubber and crosslink density stated opposite results in the fourth mixing method. The higher the bound rubber the lower the crosslink density. Without regard to mixing methods, there is a non-linear relationship between bound rubber formation and crosslink density determination

  20. Electron linear accelerator system for natural rubber vulcanization

    Science.gov (United States)

    Rimjaem, S.; Kongmon, E.; Rhodes, M. W.; Saisut, J.; Thongbai, C.

    2017-09-01

    Development of an electron accelerator system, beam diagnostic instruments, an irradiation apparatus and electron beam processing methodology for natural rubber vulcanization is underway at the Plasma and Beam Physics Research Facility, Chiang Mai University, Thailand. The project is carried out with the aims to improve the qualities of natural rubber products. The system consists of a DC thermionic electron gun, 5-cell standing-wave radio-frequency (RF) linear accelerator (linac) with side-coupling cavities and an electron beam irradiation apparatus. This system is used to produce electron beams with an adjustable energy between 0.5 and 4 MeV and a pulse current of 10-100 mA at a pulse repetition rate of 20-400 Hz. An average absorbed dose between 160 and 640 Gy is expected to be archived for 4 MeV electron beam when the accelerator is operated at 400 Hz. The research activities focus firstly on assembling of the accelerator system, study on accelerator properties and electron beam dynamic simulations. The resonant frequency of the RF linac in π/2 operating mode is 2996.82 MHz for the operating temperature of 35 °C. The beam dynamic simulations were conducted by using the code ASTRA. Simulation results suggest that electron beams with an average energy of 4.002 MeV can be obtained when the linac accelerating gradient is 41.7 MV/m. The rms transverse beam size and normalized rms transverse emittance at the linac exit are 0.91 mm and 10.48 π mm·mrad, respectively. This information can then be used as the input data for Monte Carlo simulations to estimate the electron beam penetration depth and dose distribution in the natural rubber latex. The study results from this research will be used to define optimal conditions for natural rubber vulcanization with different electron beam energies and doses. This is very useful for development of future practical industrial accelerator units.

  1. Antibacterial activity of the latex of Argemone ochroleuca Sweet

    International Nuclear Information System (INIS)

    Saad A. Alamri; Mahmoud F. Moustafa

    2010-01-01

    To investigate the antibacterial effect of the crude latex of Argemone ochroleuca (A. ochroleuca) as antibacterial potential against a range of human pathogenic bacteria. This study was carried out at King Khalid University, Abha, Kingdom of Saudi Arabia from January to March 2010. Seventeen ml of fresh latex from A. ochroleuca Sweet was collected, and the antibacterial activity of crude and diluted latex were examined using one ml of standardized inoculum suspension, and using the agar diffusion method test against Bacillus subtilis, Enterobacter aerogenes, Micrococcus luteus, Escherichia coli, and Staphylococcus aureus. All inoculated plates were incubated aerobically at 290C for 48 hours. The diameter of the zones of inhibition was measured to the nearest mm. The crude latex of A. ochroleuca exhibited a potent antibacterial effect on all bacterial strains examined. The zones of inhibition against the tested bacteria were found in the range of 9.30 - 40.3 mm along with their respective minimum inhibitory concentration values 100 ul/ml. The observable inhibition on selected bacteria by latex of A. ochroleuca makes it a promising alternative as a potential source of natural antibacterial (Author).

  2. Respiratory and dermal symptoms in Thai nurses using latex products.

    Science.gov (United States)

    Supapvanich, C; Povey, A C; de Vocht, F

    2013-09-01

    Despite known health risks related to the use of powdered latex gloves (PLGs), they are still widely used in hospitals in developing countries due to the high cost of alternatives. To determine the prevalence of dermal and respiratory symptoms associated with latex glove use in nurses in Thailand and evaluate the influence of previously reported occupational risk factors in this population. A cross-sectional study in female nurses working in three Thai hospitals. Participants completed a questionnaire on demographics, occupational and personal history, use of latex products at work and dermal and respiratory symptoms attributed to occupational use of latex gloves. Of 899 nurses, 18% reported health effects attributed to the use of latex products. After adjustment for confounding, occupational risk factors associated with increased reporting of dermal symptoms included wearing more than 15 pairs of PLG per day (odds ratio (OR): 2.10, 95% confidence interval (CI): [1.32-3.34]), using chlorhexidine (OR: 2.07, 95% CI: [1.22-3.52]) and being an operating theatre nurse (OR: 2.46, 95% CI: [1.47-4.12]). Being a labour ward nurse (OR: 3.52, 95% CI: [1.26-9.85]) was the only factor associated with increased reporting of respiratory symptoms. Continuing use of PLGs in Thai nurses is associated with increased prevalence of dermal symptoms compared with data from developed countries. Measures to reduce such health effects are well established and should be considered. Additionally, replacement of chlorhexidine with an alternative detergent seems advisable.

  3. Improved mechanical and functional properties of elastomer/graphite nanocomposites prepared by latex compounding

    International Nuclear Information System (INIS)

    Yang Jian; Tian Ming; Jia Qingxiu; Shi Junhong; Zhang Liqun; Lim Szuhui; Yu Zhongzhen; Mai Yiuwing

    2007-01-01

    The facile latex approach has been adopted to finely incorporate graphite nanosheets into elastomeric polymer matrix to obtain high-performance elastomeric nanocomposites with improved mechanical properties and functional properties. Scanning electron microscopy, transmission electron microscopy and X-ray diffraction experiments show that the nanostructures of the final nanocomposites exhibit a high degree of exfoliation and intercalation of graphite in the nitrile-butadiene rubber (NBR) matrix. Mechanical and dynamic-mechanical tests demonstrate that the NBR/graphite nanocomposites possess greatly increased elastic modulus and tensile strength, and desirably strong interfaces. The unexpected self-crosslinking of elastomer/graphite nanocomposites was discovered and then verified by oscillating disc rheometry and equilibrium swelling experiments. After critically examining various polymer types by X-ray photoelectron spectroscopy, electron spin resonance and Fourier transform infrared spectroscopy, a radical initiation mechanism was proposed to explain the self-crosslinking reaction. These NBR/graphite nanocomposites possess significantly improved wear resistance and gas barrier properties, and superior electrical/thermal conductivity. Such versatile functional properties make NBR nanocomposites a promising new class of advanced materials

  4. Improved mechanical and functional properties of elastomer/graphite nanocomposites prepared by latex compounding

    Energy Technology Data Exchange (ETDEWEB)

    Yang Jian [Key Laboratory for Nano-materials, Beijing University of Chemical Technology, Ministry of Education of China, Beijing 100029 (China); Key Laboratory on Preparation and Processing of Novel Polymer Materials, Beijing University of Chemical Technology, Beijing 100029 (China); Tian Ming [Key Laboratory for Nano-materials, Beijing University of Chemical Technology, Ministry of Education of China, Beijing 100029 (China); Jia Qingxiu [Key Laboratory on Preparation and Processing of Novel Polymer Materials, Beijing University of Chemical Technology, Beijing 100029 (China); Shi Junhong [Key Laboratory for Nano-materials, Beijing University of Chemical Technology, Ministry of Education of China, Beijing 100029 (China); Zhang Liqun [Key Laboratory for Nano-materials, Beijing University of Chemical Technology, Ministry of Education of China, Beijing 100029 (China); Key Laboratory on Preparation and Processing of Novel Polymer Materials, Beijing University of Chemical Technology, Beijing 100029 (China)], E-mail: zhanglq@mail.buct.edu.cn; Lim Szuhui; Yu Zhongzhen [Centre for Advanced Materials Technology (CAMT), School of Aerospace, Mechanical and Mechatronic Engineering (J07), University of Sydney, Sydney, NSW 2006 (Australia); Mai Yiuwing [Centre for Advanced Materials Technology (CAMT), School of Aerospace, Mechanical and Mechatronic Engineering (J07), University of Sydney, Sydney, NSW 2006 (Australia)], E-mail: y.mai@usyd.edu.au

    2007-10-15

    The facile latex approach has been adopted to finely incorporate graphite nanosheets into elastomeric polymer matrix to obtain high-performance elastomeric nanocomposites with improved mechanical properties and functional properties. Scanning electron microscopy, transmission electron microscopy and X-ray diffraction experiments show that the nanostructures of the final nanocomposites exhibit a high degree of exfoliation and intercalation of graphite in the nitrile-butadiene rubber (NBR) matrix. Mechanical and dynamic-mechanical tests demonstrate that the NBR/graphite nanocomposites possess greatly increased elastic modulus and tensile strength, and desirably strong interfaces. The unexpected self-crosslinking of elastomer/graphite nanocomposites was discovered and then verified by oscillating disc rheometry and equilibrium swelling experiments. After critically examining various polymer types by X-ray photoelectron spectroscopy, electron spin resonance and Fourier transform infrared spectroscopy, a radical initiation mechanism was proposed to explain the self-crosslinking reaction. These NBR/graphite nanocomposites possess significantly improved wear resistance and gas barrier properties, and superior electrical/thermal conductivity. Such versatile functional properties make NBR nanocomposites a promising new class of advanced materials.

  5. Advances in rubber/halloysite nanotubes nanocomposites.

    Science.gov (United States)

    Jia, Zhixin; Guo, Baochun; Jia, Demin

    2014-02-01

    The research advances in rubber/halloysite nanotubes (rubber/HNTs) nanocomposites are reviewed. HNTs are environmentally-friendly natural nanomaterials, which could be used to prepare the rubber-based nanocomposites with high performance and low cost. Unmodified HNTs could be adopted to prepare the rubber/HNTs composites with improved mechanical properties, however, the rubber/HNTs nanocomposites with fine morphology and excellent properties were chiefly prepared with various modifiers by in situ mixing method. A series of rubber/HNTs nanocomposites containing several rubbers (SBR, NR, xSBR, NBR, PU) and different modifiers (ENR, RH, Si69, SA, MAA, ILs) have been investigated. The results showed that all the rubber/HNTs nanocomposites achieved strong interfacial interaction via interfacial covalent bonds, hydrogen bonds or multiple interactions, realized significantly improved dispersion of HNTs at nanoscale and exhibited excellent mechanical performances and other properties.

  6. Rubber modification of asphalt binders and mixes

    Energy Technology Data Exchange (ETDEWEB)

    Morrison, G.; Hesp, S.A.M. [Queen`s Univ., Kingston, ON (Canada). Dept. of Chemistry

    1995-12-31

    The physical properties of asphalt binders and concrete, modified with waste rubber tire, were examined. In an experiment designed to address the concern of waste disposal of scrap rubber, a control asphalt, devulcanized rubber modified asphalt and a crumb rubber modified asphalt were used to make asphalt concrete mixes. The three mixes were subjected to a thermal stress test to determine their low temperature fracture temperatures and strengths. Results were discussed in terms of the binder material used. At high service temperatures, the addition of 10% devulcanized rubber was found to have no beneficial effect, whereas the addition of 10% 80 mesh crumb rubber produced a modest improvement in performance. At low temperatures, the addition of devulcanized rubber produced increased resistance to cracking up to 90%. The addition of 10% 80 mesh crumb rubber increased fracture toughness by a factor of 3.3 times. 12 refs., 3 tabs.

  7. Butyl Rubber: Compound Development and Characterization

    National Research Council Canada - National Science Library

    Sloan, James

    2000-01-01

    ...), to develop the standard butyl rubber compound. The strategy of this work was to compound- and compression-mold high-quality, uniform butyl rubber experimental sheets and to evaluate their cure properties, mechanical properties...

  8. Electrospinning of PVC with natural rubber

    Science.gov (United States)

    Othman, Muhammad Hariz; Mohamed, Mahathir; Abdullah, Ibrahim

    2013-11-01

    Polyvinyl chloride (PVC) was mixed with natural rubbers which are liquid natural rubber (LNR), liquid epoxidised natural rubber (LENR) and liquid epoxidised natural rubber acrylate (LENRA) for a preparation of a fine non-woven fiber's mat. PVC and each natural rubbers(PVC:LENR, PVC:LNR and PVC:LENRA) were mixed based on ratio of 70:30. Electrospinning method was used to prepare the fiber. The results show that the spinnable concentration of PVC/ natural rubber/THF solution is 16 wt%. The morphology, diameter, structure and degradation temperature of electrospun fibers were investigated by scanning electron microscopy (SEM) and thermogravimetric analysis (TGA). SEM photos showed that the morphology and diameter of the fibers were mainly affected by the addition of natural rubber. TGA results suggested that PVC electrospun fiber has higher degradation temperature than those electrospun fibers that contain natural rubber.

  9. Electrospinning of PVC with natural rubber

    International Nuclear Information System (INIS)

    Othman, Muhammad Hariz; Abdullah, Ibrahim; Mohamed, Mahathir

    2013-01-01

    Polyvinyl chloride (PVC) was mixed with natural rubbers which are liquid natural rubber (LNR), liquid epoxidised natural rubber (LENR) and liquid epoxidised natural rubber acrylate (LENRA) for a preparation of a fine non-woven fiber’s mat. PVC and each natural rubbers(PVC:LENR, PVC:LNR and PVC:LENRA) were mixed based on ratio of 70:30. Electrospinning method was used to prepare the fiber. The results show that the spinnable concentration of PVC/ natural rubber/THF solution is 16 wt%. The morphology, diameter, structure and degradation temperature of electrospun fibers were investigated by scanning electron microscopy (SEM) and thermogravimetric analysis (TGA). SEM photos showed that the morphology and diameter of the fibers were mainly affected by the addition of natural rubber. TGA results suggested that PVC electrospun fiber has higher degradation temperature than those electrospun fibers that contain natural rubber

  10. Electrospinning of PVC with natural rubber

    Energy Technology Data Exchange (ETDEWEB)

    Othman, Muhammad Hariz; Abdullah, Ibrahim [Department of Chemistry, Faculty of Science and Technology, Universiti Kebangsaan Malaysia, 43600 Bangi, Selangor (Malaysia); Mohamed, Mahathir [Radiation Processing Technology Division (BTS), Malaysian Nuclear Agency, Bangi, 43000, Kajang (Malaysia)

    2013-11-27

    Polyvinyl chloride (PVC) was mixed with natural rubbers which are liquid natural rubber (LNR), liquid epoxidised natural rubber (LENR) and liquid epoxidised natural rubber acrylate (LENRA) for a preparation of a fine non-woven fiber’s mat. PVC and each natural rubbers(PVC:LENR, PVC:LNR and PVC:LENRA) were mixed based on ratio of 70:30. Electrospinning method was used to prepare the fiber. The results show that the spinnable concentration of PVC/ natural rubber/THF solution is 16 wt%. The morphology, diameter, structure and degradation temperature of electrospun fibers were investigated by scanning electron microscopy (SEM) and thermogravimetric analysis (TGA). SEM photos showed that the morphology and diameter of the fibers were mainly affected by the addition of natural rubber. TGA results suggested that PVC electrospun fiber has higher degradation temperature than those electrospun fibers that contain natural rubber.

  11. Latex-modified fiber-reinforced concrete bridge deck overlay : construction/interim report.

    Science.gov (United States)

    1993-06-01

    Latex-modified concrete (LMC) is Portland cement concrete (PCC) with an admixture of latex. LMC is considered to be nearly impermeable to chlorides and is extensively used to construct bridge deck overlays. Unfortunately, some of these overlays have ...

  12. Surfactant and counter-ion distribution in styrene-butyl acrylate-acrylic acid dry latex submonolayers

    Directory of Open Access Journals (Sweden)

    Keslarek Amauri José

    2004-01-01

    Full Text Available Styrene-butyl acrylate-acrylic acid latex submonolayers prepared using a non-reactive phosphate surfactant together with a reactive sulfonate surfactant were examined in a transmission microscope using electron energy loss spectroscopy imaging (ESI-TEM. Phosphorus is nearly absent from the particles core but it is detected in a thick shell and in unusual, strongly scattering structures with a low carbon content, and largely made out of inorganic phosphate. P is also dispersed outside the particles, while S is uniformly distributed within then. The Na and N elemental maps show that the respective monovalent ions (Na+ and NH4+ have different distributions, in the latex: Na signal within the particles is stronger than in the background, while N is accumulated at the particle borders. The distributions of surfactant and counter-ions are thus different from some current assumptions, but they support recent results on the distribution of ionic constituents in latex films, by scanning electric potential microscopy.

  13. Rubber friction and tire dynamics

    International Nuclear Information System (INIS)

    Persson, B N J

    2011-01-01

    We propose a simple rubber friction law, which can be used, for example, in models of tire (and vehicle) dynamics. The friction law is tested by comparing numerical results to the full rubber friction theory (Persson 2006 J. Phys.: Condens. Matter 18 7789). Good agreement is found between the two theories. We describe a two-dimensional (2D) tire model which combines the rubber friction model with a simple mass-spring description of the tire body. The tire model is very flexible and can be used to accurately calculate μ-slip curves (and the self-aligning torque) for braking and cornering or combined motion (e.g. braking during cornering). We present numerical results which illustrate the theory. Simulations of anti-blocking system (ABS) braking are performed using two simple control algorithms.

  14. Rubber friction and tire dynamics.

    Science.gov (United States)

    Persson, B N J

    2011-01-12

    We propose a simple rubber friction law, which can be used, for example, in models of tire (and vehicle) dynamics. The friction law is tested by comparing numerical results to the full rubber friction theory (Persson 2006 J. Phys.: Condens. Matter 18 7789). Good agreement is found between the two theories. We describe a two-dimensional (2D) tire model which combines the rubber friction model with a simple mass-spring description of the tire body. The tire model is very flexible and can be used to accurately calculate μ-slip curves (and the self-aligning torque) for braking and cornering or combined motion (e.g. braking during cornering). We present numerical results which illustrate the theory. Simulations of anti-blocking system (ABS) braking are performed using two simple control algorithms.

  15. Fundamental studies on dynamic wear behavior of SBR rubber compounds modified by SBR rubber powder

    OpenAIRE

    Euchler, Eric; Heinrich, Gert; Michael, Hannes; Gehde, Michael; Stocek, Radek; Kratina, Ondrej; Kipscholl, Reinhold; Bunzel, Jörg-Michael; Saal, Wolfgang

    2016-01-01

    The aim of this study is focused on the experimental investigation of dynamic wear behavior of carbon black filled rubber compounds comprising pristine styrene butadiene rubber (SBR) together with incorporated SBR ground rubber (rubber powder). We also analyzed and described quantitatively the service conditions of some dynamically loaded rubber products, which are liable to wear (e.g. conveyor belts, tires). Beside the well-known standard test method to characterize wear resistance at steady...

  16. 75 FR 38119 - Polychloroprene Rubber From Japan

    Science.gov (United States)

    2010-07-01

    ... Rubber From Japan AGENCY: United States International Trade Commission. ACTION: Institution of a five-year review concerning the antidumping duty finding on polychloroprene rubber from Japan. SUMMARY: The... on polychloroprene rubber from Japan would be likely to lead to continuation or recurrence of...

  17. IMMEDIATE AND DELAYED HYPERSENSITIVITY REACTIONS TO LATEX GLOVES IN A DENTAL STUDENT. A case report.

    Directory of Open Access Journals (Sweden)

    Iliyana Stoeva

    2011-08-01

    Full Text Available The article presents a case of dental student with immediate and delayed hypersensitivity reaction to latex gloves. Symptoms appeared during the second year of regularly using of latex gloves. The student was with no history of allergies and no previous exposure to latex products.

  18. Thermal, mechanical, and moisture absorption properties of egg white protein bioplastics with natural rubber and glycerol.

    Science.gov (United States)

    Jones, Alexander; Zeller, Mark Ashton; Sharma, Suraj

    2013-07-03

    Petroleum-based plastics have many drawbacks: the large amount of energy required to produce the plastic, the waste generated as a result of plastic production, and the accumulation of waste due to slow degradation rate. It is because of these negative attributes of conventional plastic use that attention is being focused on environmentally friendly plastics from alternative sources. Albumin protein provides one possible source of raw material, with inherent antimicrobial properties that may make it suitable for medical applications. We conducted this study to investigate the various bioplastic properties of the albumin with the use of three plasticizers - water, glycerol, and natural rubber latex. Based on results, 75:25 albumin-water, 75:25 albumin-glycerol, and 80:20 albumin-natural rubber were the best blending ratios for each plasticizer for a subsequent time study to determine water stability, with the 80:20 albumin-natural rubber blend ratio having possessed the best thermal, tensile, and viscoelastic properties overall.

  19. Management of flat or inverted nipples with simple rubber bands.

    Science.gov (United States)

    Chakrabarti, Kamalendu; Basu, Subhra

    2011-08-01

    Occurrences of flat or inverted nipples are not uncommon problems, and although they should not preclude breastfeeding, they often seriously hamper initiation and continuation of breastfeeding. Various therapies including nipple exercise, breast shells, inverted syringes, or surgical corrections have been reported with varying success rates. A new method has been devised by the authors that consisted of tying a rubber band around the base of the nipple, with the help of a syringe applicator, to make it prominent. Latex rubber bands cut from condom rims were used in this study. The band had to be worn only during feeding. This method was tested on 19 mothers with flat, inverted, or otherwise deformed nipples. The babies were born in hospitals and were between 9 and 38 days old, mostly fed by bottle feeding, at the time of presentation. The mothers had been counseled about the importance of good attachment during breastfeeding and shown the new method. They were instructed to use the method at home and attend follow-up on day 3, day 7, and day 28. Sixty-three percent of mothers could achieve latching at the breast with good attachment within 3 days, and all did by the end of the month, as nipples no longer remained a problem. The insufficiency of milk was gradually taken care of by frequent suckling with time. No complications like pain or slipping of the band were reported. This simple method may be a good bedside solution for flat/retracted nipples. The authors strongly believe that if the new method is applied immediately after birth under supervision, no mother with nipple problem will be required to feed nonhuman milk to her baby.

  20. Use of rubber crumbs in cement concrete

    Science.gov (United States)

    Longvinenko, A. A.

    2018-03-01

    Rubber crumb obtained from worn out tires has been increasingly used over the last 15-20 years, especially in manufacture of asphalt and cement concrete mixtures. This review pays principal attention to application of the rubber crumb to cement concrete mixtures. Use of the rubber crumb in cement concrete is not as successful as in asphalt concrete mixtures, due to incompatibility problems linked to chemical composition and a significant difference in rigidity between the rubber crumb and concrete mixture aggregates. Different methods are proposed and studied to mitigate the adverse influence and increase the beneficial effects of the rubber crumb when added to cement concrete.

  1. Growth trends, genotype-environment interaction and genetic gains in six-year-old rubber tree clones (Hevea in São Paulo State, Brazil

    Directory of Open Access Journals (Sweden)

    Gonçalves Paulo de Souza

    1998-01-01

    Full Text Available Budwood from seven different clones of rubber tree [Hevea brasiliensis (Willd. ex Adr. de Juss. Müell. Arg.] was planted in replicated trials in four different test sites in the plateau region of the state of São Paulo, Brazil. The clones represented a range of imported germplasm, whereas the locations were selected to represent a range of rubber growing areas. Girths were measured for six years consecutively, before the initiation of tapping for latex. Total number of latex vessel rings (lvr and bark thickness (bt were measured at six years. The largest average for all characters was observed in Matão. Overall means for girth, total number of latex vessel rings and bark thickness at six years were 35.26 cm, 11.30 units and 4.83 mm, respectively. Both the test sites and clones showed statistically significant differences in girth, lvr and bt values. There were significant clone x site interactions. Girth at one year was not a reliable predictor of future field performance. Broad sense heritability for girth was 0.16, and for lvr and bt it was 0.28 and 0.40, respectively, at six years. Repeatability was quite high, from 0.52 to 0.75 for all characters in all years. When two clones out of seven were selected, expected genetic gain in girth was about 2.0%; for lvr and bt it was 7.0% and 14.6%, respectively.

  2. Plant Growth and Water Purification of Porous Vegetation Concrete Formed of Blast Furnace Slag, Natural Jute Fiber and Styrene Butadiene Latex

    Directory of Open Access Journals (Sweden)

    Hwang-Hee Kim

    2016-04-01

    Full Text Available The purpose of this study is to investigate porous vegetation concrete formed using the industrial by-products blast furnace slag powder and blast furnace slag aggregates. We investigated the void ratio, compressive strength, freeze–thaw resistance, plant growth and water purification properties using concretes containing these by-products, natural jute fiber and latex. The target performance was a compressive strength of ≥12 MPa, a void ratio of ≥25% and a residual compressive strength of ≥80% following 100 freeze–thaw cycles. Using these target performance metrics and test results for plant growth and water purification, an optimal mixing ratio was identified. The study characterized the physical and mechanical properties of the optimal mix, and found that the compressive strength decreased compared with the default mix, but that the void ratio and the freeze–thaw resistance increased. When latex was used, the compressive strength, void ratio and freeze–thaw resistance all improved, satisfying the target performance metrics. Vegetation growth tests showed that plant growth was more active when the blast furnace slag aggregate was used. Furthermore, the use of latex was also found to promote vegetation growth, which is attributed to the latex forming a film coating that suppresses leaching of toxic components from the cement. Water purification tests showed no so significant differences between different mixing ratios; however, a comparison of mixes with and without vegetation indicated improved water purification in terms of the total phosphorus content when vegetation had been allowed to grow.

  3. Influence of the Surfactant Nature on the Occurrence of Self-Assembly between Rubber Particles and Thermally Reduced Graphite Oxide during the Preparation of Natural Rubber Nanocomposites

    Directory of Open Access Journals (Sweden)

    Héctor Aguilar-Bolados

    2015-01-01

    Full Text Available The natural rubber (NR latex consists of polymer particles charged negatively due to the adsorbed phospholipids and proteins molecules. The addition of stable aqueous suspension of thermally reduced graphite oxide (TRGO stabilized by ionic surfactants to NR latex can favor the occurrence of interaction between the stabilized TRGO and NR particles. Herein, the use of two surfactants of different nature, namely, sodium dodecyl sulfate (SDS and dodecyltrimethylammonium bromide (DTAB, for the preparation of (TRGO/NR nanocomposites, is reported. Zeta potential and particle size measurements indicated that the use of DTAB as cationic surfactant results in the flocculation of NR particles and promoted the formation of ion-pair interactions between TRGO and the proteins and/or phospholipids present on the NR surface. This indicates that the use of DTAB can promote a self-assembly phenomenon between TRGO with adsorbed DTAB molecules and NR particles. The occurrence of self-assembly phenomenon allows obtaining homogenous dispersion of TRGO particles in the polymer matrix. The TRGO/NR nanocomposites prepared by the use of DTAB exhibited superior mechanical properties and excellent electrical conductivities reaching values of stress at 500% strain of 3.02 MPa and 10−4 S/cm, respectively.

  4. Soft matter: rubber and networks

    Science.gov (United States)

    McKenna, Gregory B.

    2018-06-01

    Rubber networks are important and form the basis for materials with properties ranging from rubber tires to super absorbents and contact lenses. The development of the entropy ideas of rubber deformation thermodynamics provides a powerful framework from which to understand and to use these materials. In addition, swelling of the rubber in the presence of small molecule liquids or solvents leads to materials that are very soft and ‘gel’ like in nature. The review covers the thermodynamics of polymer networks and gels from the perspective of the thermodynamics and mechanics of the strain energy density function. Important relationships are presented and experimental results show that the continuum ideas contained in the phenomenological thermodynamics are valid, but that the molecular bases for some of them remain to be fully elucidated. This is particularly so in the case of the entropic gels or swollen networks. The review is concluded with some perspectives on other networks, ranging from entropic polymer networks such as thermoplastic elastomers to physical gels in which cross-link points are formed by glassy or crystalline domains. A discussion is provided for other physical gels in which the network forms a spinodal-like decomposition, both in thermoplastic polymers that form a glassy network upon phase separation and for colloidal gels that seem to have a similar behavior.

  5. Cryogenic Deflashing for Rubber Products

    Directory of Open Access Journals (Sweden)

    Abhilash M.

    2018-01-01

    Full Text Available Deflashing is the process of removal of excess flashes from the rubber products. Initially deflashing was a manual operation where dozen of workers, seated at small work stations would take each part and trim the excess rubber off with scissors, knives or by grinding. Still the same method is employed in most of the rubber industry. The drawbacks of this method are demand inconsistent and repeatable quality. Work done by hand is often inconsistent. There are commercially available cryogenic deflashing machine but they are too expensive hence cost effectiveness is also a prime factor. The objective of this paper is to develop a technique, to identify the media through which the flashes can be removed easily and effectively. Based on the test results obtained from testing of five different types of media, ABCUT Steel media gave best results. The testing of the ABCUT Steel media on rubber samples like O-rings, grommet tail door, bottom bush etc. shows good results.

  6. Streptococcus thermophilus and its biosurfactants inhibit adhesion by Candida spp. on silicone rubber

    NARCIS (Netherlands)

    Busscher, HJ; vanHoogmoed, CG; GeertsemaDoornbusch, GI; vanderKuijlBooij, M; vanderMei, HC

    1997-01-01

    The adhesion of yeasts, two Candida albicans and two Candida tropicalis strains isolated from naturally colonized voice prostheses, to silicone rubber with and without a salivary conditioning film in the absence and presence of adhering Streptococcus thermophilus B, a biosurfactant-releasing dairy

  7. Polybutadiene latex particle size distribution analysis utilizing a disk centrifuge

    NARCIS (Netherlands)

    Verdurmen, E.M.F.J.; Albers, J.G.; German, A.L.

    1994-01-01

    Polybutadiene (I) latexes prepd. by emulsifier-free emulsion polymn. and having particle diam. 50-300 nm for both unimodal and bimodal particles size distributions were analyzed by the line-start (LIST) method in a Brookhaven disk centrifuge photosedimentometer. A special spin fluid was designed to

  8. Oil-Acrylic hybrid latexes as binders for waterborne coatings

    NARCIS (Netherlands)

    Hamersveld, E.M.S.; Es, van J.J.G.S.; German, A.L.; Cuperus, F.P.; Weissenborn, P.; Hellgren, A.C.

    1999-01-01

    The combination of the characteristics of oil, or alkyd, emulsions and acrylic latexes in a waterborne binder has been the object of various studies in the past. Strategies for combining the positive properties of alkyds, e.g. autoxidative curing, gloss and penetration in wood, with the fast drying

  9. Oil-acrylic hybrid latexes as binders for waterborne coatings

    NARCIS (Netherlands)

    Hamersveld, van E.M.S.; Es, van J.; German, A.L.; Cuperus, F.P.; Weissenborn, P.; Hellgren, A.C.

    1999-01-01

    The combination of the characteristics of oil, or alkyd, emulsions and acrylic latexes in a waterborne binder has been the object of various studies in the past. Strategies for combining the positive properties of alkyds, e.g. autoxidative curing, gloss and penetration in wood, with the fast drying

  10. The construction and commissioning of MINT's latex irradiator

    International Nuclear Information System (INIS)

    Razali Hamzah; Muhd Khairi Muhd Said; Muhd Ariff Hamzah; Wan Manshol Wan Zin; Taiman Kadni

    1996-01-01

    The construction and installation of MINT's automatic continuous latex irradiator is described. MINT cooperated with NUKEM to design the plant. Construction was done by local building consultants and local contractor. The installation of the plant includes local fabrication components and imported components. The plant is automatically controlled by a computer system. Features of plant is described

  11. Study of glucoamylase immobilization in butadiene nitrile latex membrane

    International Nuclear Information System (INIS)

    Miller, E.

    1992-01-01

    Attempts have been undetaken to immobilize glucoamylaze by means of butadiene nitrile latex in the presence of a chemical initiator and 60 Co γ-radiation. The activity, stability of conjugates in the membrane and permeability of oxygen in these membranes were determined. (author) 14 refs.; 5 figs

  12. Acetylcholinesterase Inhibitory and Antioxidant Properties of Euphorbiacharacias Latex

    Directory of Open Access Journals (Sweden)

    Francesca Pintus

    2013-03-01

    Full Text Available The aim of the present study was to evaluate the acetylcholinesterase inhibitory capacity and the antioxidant properties of extracts of Euphorbia characias latex, a Mediterranean shrub. We performed a new extraction method involving the use of the trichloroacetic acid. The extract showed high antioxidant activity, was rich in total polyphenolic and flavonoid content and exhibited substantial inhibition of acetylcholinesterase activity.

  13. LaTeX - Know what you are missing

    Directory of Open Access Journals (Sweden)

    Gunther Maier

    2016-11-01

    Full Text Available This article gives a brief introduction to \\LaTeX\\ and related tools. The aim is to give an overview, to demonstrate the flexibility and versatility of the software, and to assist the reader taking first steps using it. The article links to a number of valuable resources for further information.

  14. Latex allergy in an infant with acquired hydrocephalus | Ehiozw ...

    African Journals Online (AJOL)

    We report the case of a 3 month old male infant with acquired hydrocephalus undergoing ventriculo-peritoneal shunt insertion who developed wheals and suffered a respiratory arrest following contact with latex gloves. The need for anaesthetists to effectively diagnose and properly manage this rare clinical entity is ...

  15. Partial swelling of latex particles by two monomers

    NARCIS (Netherlands)

    Noel, E.F.J.; Maxwell, I.A.; German, A.L.

    1993-01-01

    The swelling of polymeric latex particles with solvent and monomer is of great importance for the emulsion polymn. process in regard to compn. drift and rate of polymn. For the monomer combination, Me acrylate-vinyl acetate, both satn. and partial swelling were detd. exptl. Theories for satn.

  16. Expression Profiling of Mitogen-Activated Protein Kinase Genes Reveals Their Evolutionary and Functional Diversity in Different Rubber Tree (Hevea brasiliensis Cultivars

    Directory of Open Access Journals (Sweden)

    Xiang Jin

    2017-10-01

    Full Text Available Rubber tree (Hevea brasiliensis is the only commercially cultivated plant for producing natural rubber, one of the most essential industrial raw materials. Knowledge of the evolutionary and functional characteristics of kinases in H. brasiliensis is limited because of the long growth period and lack of well annotated genome information. Here, we reported mitogen-activated protein kinases in H. brasiliensis (HbMPKs by manually checking and correcting the rubber tree genome. Of the 20 identified HbMPKs, four members were validated by proteomic data. Protein motif and phylogenetic analyses classified these members into four known groups comprising Thr-Glu-Tyr (TEY and Thr-Asp-Tyr (TDY domains, respectively. Evolutionary and syntenic analyses suggested four duplication events: HbMPK3/HbMPK6, HbMPK8/HbMPK9/HbMPK15, HbMPK10/HbMPK12 and HbMPK11/HbMPK16/HbMPK19. Expression profiling of the identified HbMPKs in roots, stems, leaves and latex obtained from three cultivars with different latex yield ability revealed tissue- and variety-expression specificity of HbMPK paralogues. Gene expression patterns under osmotic, oxidative, salt and cold stresses, combined with cis-element distribution analyses, indicated different regulation patterns of HbMPK paralogues. Further, Ka/Ks and Tajima analyses suggested an accelerated evolutionary rate in paralogues HbMPK10/12. These results revealed HbMPKs have diverse functions in natural rubber biosynthesis, and highlighted the potential possibility of using MPKs to improve stress tolerance in future rubber tree breeding.

  17. In-depth proteome analysis of the rubber particle of Hevea brasiliensis (para rubber tree).

    Science.gov (United States)

    Dai, Longjun; Kang, Guijuan; Li, Yu; Nie, Zhiyi; Duan, Cuifang; Zeng, Rizhong

    2013-05-01

    The rubber particle is a special organelle in which natural rubber is synthesised and stored in the laticifers of Hevea brasiliensis. To better understand the biological functions of rubber particles and to identify the candidate rubber biosynthesis-related proteins, a comprehensive proteome analysis was performed on H. brasiliensis rubber particles using shotgun tandem mass spectrometry profiling approaches-resulting in a thorough report on the rubber particle proteins. A total of 186 rubber particle proteins were identified, with a range in relative molecular mass of 3.9-194.2 kDa and in isoelectric point values of 4.0-11.2. The rubber particle proteins were analysed for gene ontology and could be categorised into eight major groups according to their functions: including rubber biosynthesis, stress- or defence-related responses, protein processing and folding, signal transduction and cellular transport. In addition to well-known rubber biosynthesis-related proteins such as rubber elongation factor (REF), small rubber particle protein (SRPP) and cis-prenyl transferase (CPT), many proteins were firstly identified to be on the rubber particles, including cyclophilin, phospholipase D, cytochrome P450, small GTP-binding protein, clathrin, eukaryotic translation initiation factor, annexin, ABC transporter, translationally controlled tumour protein, ubiquitin-conjugating enzymes, and several homologues of REF, SRPP and CPT. A procedure of multiple reaction monitoring was established for further protein validation. This comprehensive proteome data of rubber particles would facilitate investigation into molecular mechanisms of biogenesis, self-homeostasis and rubber biosynthesis of the rubber particle, and might serve as valuable biomarkers in molecular breeding studies of H. brasiliensis and other alternative rubber-producing species.

  18. A novel arctigenin-containing latex glove prevents latex allergy by inhibiting type I/IV allergic reactions.

    Science.gov (United States)

    Wang, Yong-Xin; Xue, Dan-Ting; Liu, Meng; Zhou, Zheng-Min; Shang, Jing

    2016-03-01

    The present study aimed at developing a natural compound with anti-allergic effect and stability under latex glove manufacturing conditions and investigating whether its anti-allergic effect is maintained after its addition into the latex. The effects of nine natural compounds on growth of the RBL-2H3 cells and mouse primary spleen lymphocytes were determined using MTT assay. The compounds included glycyrrhizin, osthole, tetrandrine, tea polyphenol, catechin, arctigenin, oleanolic acid, baicalin and oxymatrine. An ELISA assay was used for the in vitro anti-type I/IV allergy screening; in this process β-hexosaminidase, histamine, and IL-4 released from RBL-2H3 cell lines and IFN-γ and IL-2 released from mouse primary spleen lymphocytes were taken as screening indices. The physical stability of eight natural compounds and the dissolubility of arctigenin, selected based on the in vitro pharnacodynamaic screening and the stability evaluation, were detected by HPLC. The in vivo pharmacodynamic confirmation of arctigenin and final latex product was evaluated with a passive cutaneous anaphylaxis (PCA) model and an allergen-specific skin response model. Nine natural compounds showed minor growth inhibition on RBL-2H3 cells and mouse primary spleen lymphocytes. Baicalin and arctigenin had the best anti-type I and IV allergic effects among the natural compounds based on the in vitro pharmacodynamic screening. Arctigenin and catechin had the best physical stability under different manufacturing conditions. Arctigenin was the selected for further evaluation and proven to have anti-type I and IV allergic effects in vivo in a dose-dependent manner. The final product of the arctigenin-containing latex glove had anti-type I and IV allergic effects in vivo which were mainly attributed to arctigenin as proved from the dissolubility results. Arctigenin showed anti-type I and IV allergic effects in vitro and in vivo, with a good stability under latex glove manufacturing conditions

  19. The role of linked phospholipids in the rubber-filler interaction in carbon nanotube (CNT) filler natural rubber (NR) composites

    NARCIS (Netherlands)

    Le, H.H.; Abhijeet, S.; Ilish, S.; Klehm, J.; Henning, S.; Beiner, M.; Sarkawi, S.S.; Dierkes, Wilma K.; Das, A.; Fischer, D.; Stöckelhuber, K.-W.; Wiessner, S.; Khatiwada, S.P.; Adhikari, R.; Pham, T.; Heinrich, G.; Radusch, H.-J.

    2014-01-01

    The aim of the present work is to evidence the role of the linked phospholipids of natural rubber (NR) in the rubber-carbon nanotube (CNT) interactions in rubber composites. Three rubbers namely NR, deproteinized NR (DPNR) and a synthetic rubber isoprene (IR) were used as matrix for CNTs. The

  20. Effect of electron beam-cross-linked gels on the rheological properties of raw natural rubber

    Energy Technology Data Exchange (ETDEWEB)

    Mitra, Suman; Chattopadhyay, Santanu [Rubber Technology Centre, Indian Institute of Technology, Kharagpur, West Bengal 721302 (India); Bharadwaj, Y.K.; Sabharwal, S. [Radiation Technology Development Section, Bhabha Atomic Research Center, Trombay, Mumbai 400085 (India); Bhowmick, Anil K. [Rubber Technology Centre, Indian Institute of Technology, Kharagpur, West Bengal 721302 (India)], E-mail: anilkb@rtc.iitkgp.ernet.in

    2008-05-15

    Electron beam (EB)-cross-linked natural rubber (NR) gels were prepared from latex and characterized by various techniques. The addition of a small amount of these gels to raw NR was found to reduce the apparent shear viscosity and die swell remarkably. This effect was further enhanced with the addition of butyl acrylate as a sensitizer. The apparent shear viscosity first decreased up to 8 phr of gel loading and then increased. However, the percent die swell value decreased steadily upon gel loading. These were explained by calculating principal normal stress difference, the activation energy of melt flow and characteristics of EB-cross-linked gels. These effects were also reflected in the changes of mechanical and dynamic mechanical properties of gel-filled raw NR. Tailoring of the above properties could be done with the help of these gels.

  1. Constructing better roads with asphalt rubber

    Directory of Open Access Journals (Sweden)

    Pais Jorge C.

    2015-12-01

    Full Text Available Brazilians mixtures containing asphalt rubber were evaluated by mechanical laboratory tests. A conventional mixture with asphalt CAP-50/70 was produced as a mixture control. With the aim of compare the Brazilians mixtures performance, a Portuguese asphalt rubber mixture was tested as well. The testing set involved the determination of the mechanical properties, fatigue and permanent deformation, of asphalt rubber produced by wet process through two different systems: continuous blend and terminal blend. The asphalt rubber morphology was evaluated in order to determine the compatibility of the systems. The asphalt rubber mixtures exhibit good resistance to permanent deformation and prolonged fatigue life in relation to mixture control. Therefore it is concluded that the application of asphalt rubber alters the characteristics of asphalt mixture in a very beneficial way.

  2. A comparative study of natural rubber modified with ground tire rubber of truck

    OpenAIRE

    Binti Haridan, Ili Liyana

    2016-01-01

    The recycling of waste rubber has considerable significance in term of environmental protection and energy conservation. Considering that most of the relevant literature is concerned with tire recycling, the aim of this work was to develop and characterize the elastomeric samples of natural rubber (NR) composites filled with ground tire rubber of truck (GTR) devulcanized by microwave (DGTR). The tire rubber was ground under ambient conditions and subjected to microwave exposure for 3, 5 and ...

  3. Radiation cured silicone rubber articles

    International Nuclear Information System (INIS)

    DuPont, J.G.; Goodwin, P.A.

    1984-01-01

    A process for making radiation cured silicone rubber articles is disclosed wherein a hydroxyl-terminated polysilaxane having a molecular weight from about 50,000 to about 2,000,000, optionally modified by mixing with up to 85% of an end-stopped silicone rubber, is mixed with from about 10 to about 70 parts per hundred of rubber of a finely divided silica filler with a particle size in the reinforcing range and other inert fillers as determined by desired final properties; the composition so prepared is formed into the desired shape at room temperature; the article so formed is precured to improve the mechanical properties of the material with which it is made by exposure to ammonia gas, ammonium hydroxide, or to the vapors or solutions of a volatile amine at room temperature; and the precured article is irradiated with high energy electrons or gamma radiation to effect a permanent cure of the material from which the article is formed

  4. Thermal endurance tests on silicone rubber specimens

    International Nuclear Information System (INIS)

    Warburton, C.

    1977-07-01

    Thermal endurance tests have been performed on a range of silicone rubber specimens at temperature above 300 0 C. It is suggested that the rubber mix A2426, the compound from which Wylfa sealing rings are manufactured, will fail at temperatures above 300 0 C within weeks. Hardness measurements show that this particular rubber performs in a similar manner to Walker's S.I.L./60. (author)

  5. LOL2 and LOL5 loci control latex production by laticifer cells in Euphorbia lathyris.

    Science.gov (United States)

    Castelblanque, Lourdes; Balaguer, Begoña; Marti, Cristina; Orozco, Marianela; Vera, Pablo

    2018-06-07

    Laticifers are specialized plant cells capable of indefinite elongation that ramify extensively and are responsible for latex biosynthesis and accumulation. However, the mechanisms underlying laticifer cell differentiation, growth and production of latex remain largely unknown. In a search for mutants showing enhanced accumulation of latex we identified two LOT OF LATEX (LOL) loci in Euphorbia lathyris. lol2 and lol5 mutants show enhanced production of latex contained within laticifer cells. The recessive lol2 mutant carries increased biosynthesis of the plant hormone jasmonoyl-isoleucine (JA-Ile) and therefore establishes a genetic link between jasmonic acid (JA) signaling and latex production in laticifers. Instead, heightened production of latex in lol5 plants obeys to enhanced proliferation of laticifer cells. Phylogenetic analysis of laticifer-expressed genes in E. lathyris and in two other latex-bearing species, Euphorbia corallioides and Euphorbia palustris, allowed the identification of canonical JA responsive elements present in the gene promoter regions of laticifer marker genes. Moreover, we identified that the hormone JA functions not as a morphogen for laticifer differentiation but as a trigger for the fill out of laticifers with latex and the associated triterpenoids. The identification of LOL loci represents a further step towards the understanding of mechanisms controlling latex production in laticifer cells. No claim to original US Government works New Phytologist © 2018 New Phytologist Trust.

  6. Treatment of wastewater from rubber industry in Malaysia ...

    African Journals Online (AJOL)

    Treatment of wastewater from rubber industry in Malaysia. ... Discharge of untreated rubber effluent to waterways resulted in water pollution that affected the human health. ... Key words: Rubber industry, effluent, waste management, Malaysia.

  7. Reinforcement of natural rubber/high density polyethylene blends with electron beam irradiated liquid natural rubber-coated rice husk

    Energy Technology Data Exchange (ETDEWEB)

    Chong, E.L.; Ahmad, Ishak [Polymer Research Center (PORCE), School of Chemical Science and Food Technology, Universiti Kebangsaan Malaysia 4, 43600 UKM Bangi, Selangor Darul Ehsan (Malaysia); Dahlan, H.M. [Radiation Processing Technology Division, Malaysian Nuclear Agency (Nuclear Malaysia), Bangi, 43000 Kajang, Selangor Darul Ehsan (Malaysia); Abdullah, Ibrahim, E-mail: dia@ukm.m [Polymer Research Center (PORCE), School of Chemical Science and Food Technology, Universiti Kebangsaan Malaysia 4, 43600 UKM Bangi, Selangor Darul Ehsan (Malaysia)

    2010-08-15

    Coating of rice husk (RH) surface with liquid natural rubber (LNR) and exposure to electron beam irradiation in air were studied. FTIR analysis on the LNR-coated RH (RHR) exposed to electron beam (EB) showed a decrease in the double bonds and an increase in hydroxyl and hydrogen bonded carbonyl groups arising from the chemical interaction between the active groups on RH surface with LNR. The scanning electron micrograph showed that the LNR formed a coating on the RH particles which transformed to a fine and clear fibrous layer at 20 kGy irradiation. The LNR film appeared as patches at 50 kGy irradiation due to degradation of rubber. Composites of natural rubber (NR)/high density polyethylene (HDPE)/RHR showed an optimum at 20-30 kGy dosage with the maximum stress, tensile modulus and impact strength of 6.5, 79 and 13.2 kJ/m{sup 2}, respectively. The interfacial interaction between the modified RH and TPNR matrix had improved on exposure of RHR to e-beam at 20-30 kGy dosage.

  8. Chemical modifications of liquid natural rubber

    Science.gov (United States)

    Azhar, Nur Hanis Adila; Rasid, Hamizah Md; Yusoff, Siti Fairus M.

    2016-11-01

    Liquid natural rubber (LNR) was synthesized via photosentisized degradation of natural rubber (NR). LNR was modified into epoxidized liquid natural rubber (LENR) and hydroxylated liquid natural rubber (LNR-OH) using Na2WO4/CH3COOH/H2O2 catalytic system. Chemical structures of LNR and modified LNRs were characterized using Attenuated Total Reflectance Fourier Transform Infrared (ATR-FTIR) and 1H Nuclear Magnetic Resonance (NMR) spectroscopies. Integration of 1H NMR was used to calculate the epoxy content (%) of LENR. 1H NMR detected the formation of LNR-OH after prolonged heating and increased of catalyst in oxidation reaction.

  9. Characterization of the rubber tree metallothionein family reveals a role in mitigating the effects of reactive oxygen species associated with physiological stress.

    Science.gov (United States)

    Huang, Yacheng; Fang, Yongjun; Long, Xiangyu; Liu, Linya; Wang, Jia; Zhu, Jinheng; Ma, Yanyan; Qin, Yunxia; Qi, Jiyan; Hu, Xinwen; Tang, Chaorong

    2018-02-07

    Metallothioneins (MTs) as reactive oxygen species (ROS) scavengers play important roles in stress response and heavy metal homeostasis. In Hevea brasiliensis (the para rubber tree that is the source of commercial natural rubber) and in other trees, the functions of MTs are not well understood. Latex exudes when the rubber tree is tapped. The flow of latex and its regeneration can be enhanced by tapping, wounding and ethylene treatment, all of which produce ROS as a by-product. Here, we show the presence of four MT genes in H. brasiliensis, comprising three Type 2 (HbMT2, -2a and -2b) and one Type 3 (HbMT3L) isoforms, representing one of the smallest MT gene families among angiosperms. The four HbMTs exhibited distinct tissue expression patterns: HbMT2 and HbMT3L mainly in leaves, HbMT2a specifically in flowers and HbMT2b in diverse tissues. The expression of HbMT2b, an isoform present in latex, decreased significantly in the latex following the stress-inducing treatments of tapping, wounding and ethephon (an ethylene generator). The expressions of the leaf-abundant isoforms, HbMT2 and -3L were up-regulated following pathogenic fungus infection and high-temperature stress, but down-regulated by low-temperature stress. These reactions were consistent with multiple defense- and hormone-responsive cis-acting elements in the HbMT promoters. Nine transcription factors were shown to implicate in the high-temperature responsiveness of HbMT2 and -3L in leaves. Overexpression of HbMT2 in Escherichia coli enhanced the bacterium's tolerance to heavy metals and ROS, consistent with its predicted role as an ROS scavenger. Taken together, our results, along with other relevant studies, suggest an important role of HbMTs in latex regeneration as well as species adaptation via the regulation of ROS homeostasis. © The Author(s) 2018. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  10. Osmotic de-swelling and swelling of latex dispersions

    International Nuclear Information System (INIS)

    Bonnet-Gonnet, Cecile

    1993-01-01

    This research thesis reports the comparison of, on the one hand, direct measurements of de-swelling resistance of latex dispersions obtained by osmotic pressure with, on the other hand, predictions made by models of electrostatic interactions. This resistance is explained in the case of sulphate-stabilised polystyrene particles (direct repulsion between charged particles), and in the case of copolymer (ps-pba) particles covered by an amphiphilic polymer (interactions between surface macromolecules and polymers). The study of de-swelling and swelling cycles highlights the existence of thresholds beyond which the concentrated dispersion has some cohesion. This irreversibility can be modelled by a Van der Waals attraction. The role of hydrophobic forces in latex destabilisation is studied [fr

  11. [Anaphylactic reaction to latex during spinal anesthesia: a case report].

    Science.gov (United States)

    Ueda, Narumi; Kitamura, Rie; Wakamori, Takeshi; Nakamura, Kumi; Konishi, Keisuke

    2008-05-01

    A 46-year-old man, with a history of atopic dermatitis and bronchial asthma, underwent surgery for an inguinal hernia. Forty-three minutes subsequent to spinal anesthesia, the patient complained suddenly of dyspnea with wheezing. Blood pressure decreased and skin eruption was observed on his chest. Postoperative laboratory tests revealed high IgE concentration, and a skin test confirmed an allergy to latex. The patient's allergic reaction was easily overlooked because of his history of bronchial asthma and the possibility that the hypotension was caused by the high spinal anesthesia. Latex allergy should be considered in any suspicious case presenting with these symptoms during surgery. After recovery, a skin test should be used to confirm the allergy to avoid repeated allergic episodes.

  12. A latex metabolite benefits plant fitness under root herbivore attack

    OpenAIRE

    Huber, M.; Epping, J.; Gronover, C.S.; Fricke, J.; Aziz, Z.; Brillatz, T.; Swyers, M.; Köllner, T.G.; Vogel, H.; Hammerbacher, A.; Triebwasser-Freese, D.; Robert, C.A.M.; Verhoeven, K.; Preite, V.; Gershenzon, J.

    2016-01-01

    Plants produce large amounts of secondary metabolites in their shoots and roots and store them in specialized secretory structures. Although secondary metabolites and their secretory structures are commonly assumed to have a defensive function, evidence that they benefit plant fitness under herbivore attack is scarce, especially below ground. Here, we tested whether latex secondary metabolites produced by the common dandelion (Taraxacum officinale agg.) decrease the performance of its major n...

  13. The entry of free radicals into polystyrene latex particles

    International Nuclear Information System (INIS)

    Adams, M.E.; Trau, M.; Gilbert, R.C.; Napper, D.R.

    1988-01-01

    Mechanistic understanding of the processes governing the kinetics of emulsion polymerization has both scientific and technical interest. One component of this process that is poorly understood at present is that of free radical entry into latex particles. Measurements were made of the entry rate coefficient as a function of temperature for free radicals entering polystyrene latex particles in seeded emulsion polymerizations initiated by γ-rays. The activation energy for entry was found to be less than 24 ± 3 kJ mol -1 , consistent with entry being controlled by a physical (e.g. diffusional) rather than a chemical process. Measurement of the entry rate coefficient as a function of the γ-ray dose rate suggested that the factors that determine the entry rate when the primary free radicals are uncharged are similar to those that determine the entry rate for charged free radicals derived from chemical initiation by peroxydisulfate. This result was consistent with measurements of the entry rate coefficient of charged free radicals derived from peroxydisulfate; these data were found to be virtually independent of both the extent of the latex surface coverage by the anionic surfactant sodium dodecyl sulfate and the ionic strength of the continuous phase. The data refute several proposals given in the literature for the rate-determining step for entry, being inconsistent with control by collision of free radicals with the latex particles, surfactant desorption, and an electrostatic barrier arising from the colloidal nature of the entering free radical. The origin of the activation energy for entry remains obscure

  14. Minimizing surgical skin incision scars with a latex surgical glove.

    Science.gov (United States)

    Han, So-Eun; Ryoo, Suk-Tae; Lim, So Young; Pyon, Jai-Kyung; Bang, Sa-Ik; Oh, Kap-Sung; Mun, Goo-Hyun

    2013-04-01

    The current trend in minimally invasive surgery is to make a small surgical incision. However, the excessive tensile stress applied by the retractors to the skin surrounding the incision often results in a long wound healing time and extensive scarring. To minimize these types of wound problems, the authors evaluated a simple and cost-effective method to minimize surgical incision scars based on the use of a latex surgical glove. The tunnel-shaped part of a powder-free latex surgical glove was applied to the incision and the dissection plane. It was fixed to the full layer of the dissection plane with sutures. The glove on the skin surface then was sealed with Ioban (3 M Health Care, St. Paul, MN, USA) to prevent movement. The operation proceeded as usual, with the retractor running through the tunnel of the latex glove. It was possible to complete the operation without any disturbance of the visual field by the surgical glove, and the glove was neither torn nor separated by the retractors. The retractors caused traction and friction during the operation, but the extent of damage to the postoperative skin incision margin was remarkably less than when the operation was performed without a glove. This simple and cost-effective method is based on the use of a latex surgical glove to protect the surgical skin incision site and improve the appearance of the postoperative scar. This journal requires that authors assign a level of evidence to each article. For a full description of these Evidence-Based Medicine ratings, please refer to the Table of Contents or the online Instructions to Authors www.springer.com/00266 .

  15. The criteria and the design of MINT's latex irradiator

    International Nuclear Information System (INIS)

    Razali Hamzah; Muhd Khairi Muhd Said; Muhd Ariff Hamzah; Wan Manshol Wan Zin; Wan Abd Hadi Wan Abu Bakar; Muhd Noor Muhd Yunus

    1996-01-01

    The demand for RVNRL is continually on the upsurge and the present irradiation technique at the present SINAGAMA plant is not sufficient and practical to meet the demand. A number of conceptual designs were evolved to design according to the requirements of cost-effective and highly efficient plant. The number of options are described. In 1994 MINT work with NUKEM to build an automatic continuous latex irradiation plant

  16. The polymerization of aniline in polystyrene latex particles

    Czech Academy of Sciences Publication Activity Database

    Blinova, Natalia V.; Reynaud, S.; Roby, F.; Trchová, Miroslava; Stejskal, Jaroslav

    2010-01-01

    Roč. 160, 15/16 (2010), s. 1598-1602 ISSN 0379-6779 R&D Projects: GA AV ČR IAA400500905; GA ČR GA203/08/0686; GA ČR GA202/09/1626 Institutional research plan: CEZ:AV0Z40500505 Keywords : polyaniline * polystyrene latex * polyaniline-polystyrene composite Subject RIV: CD - Macromolecular Chemistry Impact factor: 1.871, year: 2010

  17. Influence of ZnO and TiO_2 particle sizes in the mechanical and dielectric properties of vulcanized rubber

    International Nuclear Information System (INIS)

    Gonzalez, Neudys; Custal, Maria del Angels; Rodriguez, Daniel; Riba, Jordi-Roger; Armelin, Elaine

    2017-01-01

    The novelty of the present study relies on the straightforward sonication of ZnO and TiO_2 and incorporation to a complex formulation of latex, with other several organic-inorganic additives that influences the cross-linking reactions. The new elastomer with particles carefully sonicated exhibit improved electrical and mechanical properties. Strong interaction among the nanoparticles and the polymer amorphous phase has been proved by means of FTIR, SEM and XRD analyses. The synergistic effect of hybrid fillers with nanometric dimensions can be used to design high-performance natural rubber nanocomposites with enhanced electrical resistance and good cross-linking degree. (author)

  18. Influence of ZnO and TiO{sub 2} particle sizes in the mechanical and dielectric properties of vulcanized rubber

    Energy Technology Data Exchange (ETDEWEB)

    Gonzalez, Neudys; Custal, Maria del Angels; Rodriguez, Daniel [Sicame Company, Barcelona (Spain); Riba, Jordi-Roger [Departament d' Enginyeria Eletrica, Universitat Politecnica de Catalunya, Terrasssa (Spain); Armelin, Elaine, E-mail: elaine.armelin@upc.edu [Universitat Politecnica de Catalunya, Barcelona (Spain)

    2017-07-15

    The novelty of the present study relies on the straightforward sonication of ZnO and TiO{sub 2} and incorporation to a complex formulation of latex, with other several organic-inorganic additives that influences the cross-linking reactions. The new elastomer with particles carefully sonicated exhibit improved electrical and mechanical properties. Strong interaction among the nanoparticles and the polymer amorphous phase has been proved by means of FTIR, SEM and XRD analyses. The synergistic effect of hybrid fillers with nanometric dimensions can be used to design high-performance natural rubber nanocomposites with enhanced electrical resistance and good cross-linking degree. (author)

  19. Natural Rubber Modification For Upper Layer Of Rubberized Asphalt Paving Block AS Shock Absorber

    OpenAIRE

    Nasruddin, Nasruddin

    2017-01-01

    The research of rubber compounding modification for upper layer of rubberized asphalt paving block as shock absorber using natural rubber, styrene butadiene rubber (SBR) as synthetic rubber, fly ash as filler and also vegetable oil as plasticizer has been conducted. The research design was varying the filler Si-69, fly ash and palm oil. The five formulas A, B, C, D, and E designed by varying the amount of Si-69 (48.5; 50.75; 53.00; 55.25; and 57.50) phr; coal fly ash (4.75, 7.00, 9.25, 11.50 ...

  20. Identification and characterization of Euphorbia nivulia latex proteins.

    Science.gov (United States)

    Badgujar, Shamkant B; Mahajan, Raghunath T

    2014-03-01

    The protein profile of latex of Euphorbia nivulia Buch.-Ham. is established. Three new proteins viz., Nivulian-I, II and III have been purified to homogeneity from the latex. The relative molecular masses of Nivulian-I, II and III are 31,486.985, 43,670.846 and 52,803.470 Da respectively. Nivulian-I is a simple type of protein while Nivulian-II and III are glycoproteins. Peptide mass fingerprint analysis revealed peptides of these proteins match with Tubulin alpha-1 chain of Eleusine indica, Maturase K of Banksia quercifolia and hypothetical protein of Zea mays respectively. Tryptic digestion profile of Nivulian-I, II and III, infer the exclusive nature of latex origin proteins and may be new and are additive molecules in the dictionaries of phytoproteins or botany. This is the first of its kind, regarding characterization and validation of Nivulian-I, II and III with respect to peptide sequencing. Copyright © 2013 Elsevier B.V. All rights reserved.

  1. Efficacy of protection by latex gloves during orthodontic therapy.

    Science.gov (United States)

    Doll, G M; Zentner, A; Balan, R; Sergl, H G

    2000-01-01

    The wearing of gloves during orthodontic or dental treatment is generally indicated for reasons of hygiene and protection against infection. This study was aimed at determining the extent and localization of perforations caused by the various orthodontic treatment techniques and interrupting the infection barrier. The impermeability was tested by means of a water retention test according to European standard EN 455, Part 1, performed on 1600 Centramed (Centramed, Koblenz), Tekmedic and SafeEx non-sterile disposable latex gloves (both by Safe Med, Switzerland) and Safe Gan latex gloves with an additional acrylate coating (also by Safe Med). The perforation rate in unused gloves was between 0.5% and 7.5%, rising on average to 11% with increasing use. 36% of the total number of lesions resulted from handling removable appliances, and 57% from handling fixed appliances, especially when replacing arch wires and elastics. Most lesions were in the thumb, index finger and palm region. Only 18% of the defects were noticed by the dentists themselves. The gloves worn by beginners in their first year of postgraduate orthodontic training had about twice as many defects as those worn by qualified orthodontists. When patients with an increased risk of infection are to be treated, additional hand disinfection measures should be taken and 2 pairs of gloves worn in view of the relatively unreliable protection offered by commercially available latex gloves.

  2. Prediction of heat generation in rubber or rubber-metal springs

    Directory of Open Access Journals (Sweden)

    Banić Milan S.

    2012-01-01

    Full Text Available The temperature of rubber or rubber-metal springs increases under cyclic loading, due to hysteresis losses and low rubber thermal conductivity. Hysteresis losses correspond to energy dissipation from the rubber, which is primarily converted into heat. This well-known phenomenon, called heat build-up, is the primary reason for rubber aging. Increase in temperature within the rubber compound leads to degradation of its physical and chemical properties, increase in stiffness and loss of damping capability. This paper presents a novel procedure of heat generation prediction in rubber or rubber-metal springs. The procedure encompasses the prediction of hysteresis loss, i. e. dissipated energy within the rubber, by finite element analysis and application of a modern visco-plastic rubber constitutive model. The obtained dissipated energy was used as an input for transient thermal analysis. Verification of the proposed procedure was performed by comparison of simulation results with experimentally obtained data during the dynamic loading of the rubber specimen. The proposed procedure is highly computationally efficient and it enables time integration, which can be problematic in coupled mechanical thermal analysis. [Projekat Ministarstva nauke Republike Srbije, br. TR35005: Research and Development of New Generation of Wind Turbines of High Energy Efficiency

  3. Effect of Recycled Rubber Particles and Silica on Tensile and Tear Properties of Natural Rubber Composites

    Directory of Open Access Journals (Sweden)

    Velu CHANDRAN

    2016-05-01

    Full Text Available Application of scrap rubber and worn out tires in natural rubber compounds has been studied. The scrap rubber can, however, be recycled and compounded with natural rubber and thus can be generated as a rubber composite. In this work, recycled rubber particles (RRP were prepared using pulverization process. Then, RRP was blended with natural rubber and silica compounds, and it was synthesized by two- roll mill and hydraulic press at specified operating conditions. The samples ranging from 0 to 40 phr of RRP loaded with silica were used as constant filler. The mechanical properties and morphological analysis were carried out. The results showed that tensile strength and elongation at break gradually decreased with increasing RRP loading in natural rubber and silica compounds. Tensile modulus went down at 10 phr of RRP and then showed an increasing trend. Hardness increased up to 30 phr of RRP and tear strength increased up to 20 phr of RRP. A comparative study was also carried out with virgin natural rubber vulcanizates. The incorporation of RRP and silica up to 20 phr in natural rubber did not lower the performance of rubber articles. Morphological studies revealed that better filler dispersion, interfacial adhesion, and cross link density could increase the tensile and tear strengths.DOI: http://dx.doi.org/10.5755/j01.ms.22.2.7330

  4. Histamine mediates the pro-inflammatory effect of latex of Calotropis procera in rats

    Directory of Open Access Journals (Sweden)

    Yatin M. Shivkar

    2003-01-01

    Full Text Available Introduction: Calotropis procera is known to produce contact dermatitis and the latex of this plant produces intense inflammation when injected locally. However, the precise mode of its pro-inflammatory effect is not known. In present study we have pharmacologically characterized the inflammation induced by latex of C. procera in a rat paw edema model and determined the role of histamine in latex-induced inflammation.

  5. Latex agglutination test (LAT) for the diagnosis of typhoid fever.

    Science.gov (United States)

    Sahni, Gopal Shankar

    2013-06-01

    The efficacy of latex agglutination test in the rapid diagnosis of typhoid fever was studied and the result compared with that of blood culture. This study included 80 children suffering from typhoid fever, among which 40 were confirmed by blood culture isolation and 40 had possible typhoid fever based on high Widal's titre (a four-fold rise in the titre of antibody to typhi "O" and "H" antigen was considered as a positive Widal's test result). Eighty children, 40 with febrile illness confirmed to be other than typhoid and 40 normal healthy children were used as negative controls. The various groups were: (i) Study group ie, group I had 40 children confirmed by culture isolation of Salmonella typhi(confirmed typhoid cases). (ii) Control groups ie, (a) group II with 40 febrile controls selected from paediatrics ward where cause other than S typhi has been established, (b) group III with 40 afebrile healthy controls that were siblings of the children admitted in paediatric ward for any reason with no history of fever and TAB vaccination in the last one year, and (c) group IV with 40 children with high Widal's titre in paired sera sample. Widal's test with paired sera with a one week interval between collections were done in all 40 patients. Latex aggtutination test which could detect 900 ng/ml of antigen as observed in checker board titration, was positive in all 40 children from group I who had positive blood culture and in 30 children from group IV who had culture negative and had high Widal's titre positive. Latex agglutination test was positive in 4 children in group II and none in group III. Using blood culture positive cases as true positive and children in groups II and III as true negative, the test had a sensitivity of 100% and specificity of 96%. Latex agglutination test was found to be significantly sensitive (100%) and specific (96%) and could detect 75% more cases in group IV (possible typhoid cases). Thus latex agglutination test can be used for rapid

  6. Energy usage in the rubber industry

    Energy Technology Data Exchange (ETDEWEB)

    Soederstroem, M.

    1980-01-01

    The rubber industry has several energy-intensive steps, such as mastication of natural rubber, mixing and extrusion, and vulcanization. Opportunities for energy savings would be available with a continuous mixing process, heat recovery from cooling waters, and abandonment of thermal conduction in vulcanization. 6 figures. (DCK)

  7. Natural rubber producing plants: An overview

    African Journals Online (AJOL)

    User

    2013-03-20

    Mar 20, 2013 ... Currently, Hevea brasiliensis has been only one resource for commercial natural rubber production. ...... ADVANTAGES AND DISADVANTAGES ... polymer chain. Combinations of an amine antioxidant and a zinc dialkyldithiocarbamate have been used to counter these effects, improving guayule rubber ...

  8. UTILISATION OF RUBBER SEED OL IN THE

    African Journals Online (AJOL)

    Thermal degradation studies on polyvinyl chloride in the presence of rubber seed oil, epoxidized rubber seed oil and metal ... Epoxidation of RSO was carried out at 29°C using peractic acid ..... impurities such as pigments, Vitamins, sterols ...

  9. 75 FR 57980 - Polychloroprene Rubber From Japan

    Science.gov (United States)

    2010-09-23

    ... INTERNATIONAL TRADE COMMISSION [Investigation No. AA1921-129 (Third Review)] Polychloroprene Rubber From Japan AGENCY: United States International Trade Commission. ACTION: Termination of five-year... of the antidumping duty finding on polychloroprene rubber from Japan would be likely to lead to...

  10. Rheological testing of crumb rubber modified bitumen

    CSIR Research Space (South Africa)

    Mturi, GAJ

    2011-08-01

    Full Text Available used to analyse crumb rubber modified (CRM) bitumen is that the specified gap setting in the configuration of the DSR between the upper and lower test platens is too small to accommodate crumb rubber particles. DSR testing of CRM bitumen therefore...

  11. Characterizing Tire Crumb Rubber for Exposure Assessment

    Science.gov (United States)

    Tire crumb rubber derived from recycled tires is widely used as infill material in synthetic turf fields in the United States. An estimated 95% of the over 12,000 installed fields in the U.S. use tire crumb rubber infill alone or mixed with sand or alternative materials. Concerns...

  12. Effect of organo-clay on the dielectric relaxation response of silicone rubber

    International Nuclear Information System (INIS)

    Gharavi, N; Razzaghi-Kashani, M; Golshan-Ebrahimi, N

    2010-01-01

    Dielectric elastomers are light weight, low-cost, highly deformable and fast response smart materials capable of converting electrical energy into mechanical work or vice versa. Silicone rubber is a well-known dielectric elastomer which is used as actuator, and in order to enhance the efficiency of this smart material, compounding of silicone rubber with various fillers can be carried out. The effect of organically modified montmorillonite (OMMT) nano-clay on improvement of dielectric properties, actuation stress and its relaxation response was considered in this study. OMMT was dispersed in room temperature vulcanized (RTV) silicone rubber, and a composite film was cast. Using an in-house actuation set-up, it was shown that the actuation stress for a given electric field intensity is higher for composites than that for pristine silicone rubber. Also, the time-dependent actuation response of the samples was evaluated, and it was shown that the characteristic relaxation time of the actuation stress for composites is less than for the pristine rubber as a result of OMMT addition

  13. AC/TiO2/Rubber Composite Sheet Catalysts; Fabrication, Characterization and Photocatalytic Activities

    Directory of Open Access Journals (Sweden)

    Sriwong Chaval

    2015-01-01

    Full Text Available The AC/TiO2/Rubber (ACTR composite sheets weresuccessfully fabricated by a simply mixing of fixed TiO2 suspension and natural rubber latex (60% HA contents withthe varyingamounts of activated carbon (AC suspension, followed by stirring, pouring into apetri dish mold, drying at room temperature (RT, after that taking out from a mold, reversing and drying again at RT. Then, the as-fabricated ACTR composite sheets were characterized by X-ray diffractometer (XRD, attenuated total reflection Fourier transform infrared spectroscopy (ATR-FTIR, energy dispersive X-ray spectroscopy (EDS and scanning electron microscopy (SEMtechniques. The photocatalytic efficiencies of all ACTR composite sheet samples were evaluated by photo degrading of methylene blue (MB dye solution under UV light irradiation. The results showed that the photocatalytic activity of ACTR sheet with10.0wt%AC loading has the highest efficiency for the photo degradation of MB dye than the other sheets. This is due to the fact that it is relatively with the synergistic effect of well-combined titanium dioxide catalyst and activated carbon adsorbent.

  14. Electron spectroscopy of rubber and resin-based composites containing 2D carbon

    Energy Technology Data Exchange (ETDEWEB)

    Kaciulis, S., E-mail: saulius.kaciulis@ismn.cnr.it [Institute for the Study of Nanostructured Materials, ISMN-CNR, P.O. Box 10, Monterotondo Stazione, 00015 Roma (Italy); Mezzi, A.; Balijepalli, S.K. [Institute for the Study of Nanostructured Materials, ISMN-CNR, P.O. Box 10, Monterotondo Stazione, 00015 Roma (Italy); Lavorgna, M. [Institute of Polymers, Composites and Biomaterials, IPCB-CNR, P.le Fermi, 80055 Napoli (Italy); Xia, H.S. [State Key Laboratory of Polymer Materials Engineering, Sichuan University, Chengdu, 610065 Sichuan (China)

    2015-04-30

    Composite materials with 2D carbon (graphene and/or single wall carbon nanotubes) are very promising due to their extraordinary electrical and mechanical properties. Graphene and natural rubber composites, which may be used for the gaskets or sealants, were prepared by ultrasonically assisted latex-mixing exfoliation and in-situ reduction process, with two vulcanization approaches: roll-mixing and hot-pressing. Also the resin-based composites, filled with micro-particles of Ag and graphene or carbon nanotubes, have been studied. The standards for the compositional characterization of these materials still are not established. In addition to the mostly used techniques, such as Raman spectroscopy and electron microscopy, also Auger electron spectroscopy can be employed for the identification of graphene. In this study, the shape of C KVV peak, excited by electron beam and X-ray photons, has been investigated in different composite materials containing graphene and carbon nanotubes. A spectroscopic method for 2D carbon recognition, based on the D{sub x} parameter which is determined from C KVV signal excited by X-ray photons, was proposed and verified. Even a small content of graphene in different types of composites was sufficient for this recognition due to the dominating presence of graphene on the surface of composites. - Highlights: • Chemical composition of the rubber composites was determined by XPS. • Auger spectrum of carbon was used for graphene identification in composites. • Small content of graphene was sufficient for its recognition from the D parameter.

  15. Water absorption and mechanical properties of water-swellable natural rubber

    Directory of Open Access Journals (Sweden)

    Diew Saijun

    2009-11-01

    Full Text Available Water-swellable rubber (WSR was prepared by blending superabsorbent polymer (SAP of crosslinked poly(acrylamide-co-sodium acrylate with natural rubber in latex condition. The crosslinked poly(acrylamide-co-sodium acrylate was first prepared by inverse suspension polymerization from acrylamide and sodium acrylate monomers with potassiumpersulfate initiator and N,N-methylenebisacrylamide crosslinker. The reaction was carried out at 60oC for 40 mins. Water absorption properties, such as the degree of water absorption, water absorption rate, degree of weight loss, and mechanicalproperties of WSR were then investigated. It was found that the degree of water absorption, water absorption rate, and thedegree of weight loss increased, while tensile strength and elongation at break decreased with increasing quantity of SAP inthe blends. However, the degree of water absorption, degree of weight loss, and elongation at break decreased, but tensilestrength increased with increasing quantity of the N-tert-butyl-2-benzothiazyl sulphenamide (TBBS accelerator used in thecompounds formulation.

  16. Electron spectroscopy of rubber and resin-based composites containing 2D carbon

    International Nuclear Information System (INIS)

    Kaciulis, S.; Mezzi, A.; Balijepalli, S.K.; Lavorgna, M.; Xia, H.S.

    2015-01-01

    Composite materials with 2D carbon (graphene and/or single wall carbon nanotubes) are very promising due to their extraordinary electrical and mechanical properties. Graphene and natural rubber composites, which may be used for the gaskets or sealants, were prepared by ultrasonically assisted latex-mixing exfoliation and in-situ reduction process, with two vulcanization approaches: roll-mixing and hot-pressing. Also the resin-based composites, filled with micro-particles of Ag and graphene or carbon nanotubes, have been studied. The standards for the compositional characterization of these materials still are not established. In addition to the mostly used techniques, such as Raman spectroscopy and electron microscopy, also Auger electron spectroscopy can be employed for the identification of graphene. In this study, the shape of C KVV peak, excited by electron beam and X-ray photons, has been investigated in different composite materials containing graphene and carbon nanotubes. A spectroscopic method for 2D carbon recognition, based on the D x parameter which is determined from C KVV signal excited by X-ray photons, was proposed and verified. Even a small content of graphene in different types of composites was sufficient for this recognition due to the dominating presence of graphene on the surface of composites. - Highlights: • Chemical composition of the rubber composites was determined by XPS. • Auger spectrum of carbon was used for graphene identification in composites. • Small content of graphene was sufficient for its recognition from the D parameter

  17. Preparation and properties of natural rubber reinforced with polydopamine-coating modified carbon nanotubes

    Directory of Open Access Journals (Sweden)

    Y-L. Lu

    2017-01-01

    Full Text Available Multi-walled carbon nanotubes (MWCNTs were functionalized by polydopamine (PDA-coating and mixed with natural rubber (NR via latex compounding. Compared with pristine MWCNTs, the surface of MWCNT-PDA was covered by an amorphous and nanometer-scale PDA layer which had a large amount of oxygenic and nitric functional groups. So the MWCNT-PDA showed a perfect dispersion in NR matrix. The tensile strength of NR/MWCNT-PDA (5 phr composites is 28.6 MPa, compared with the pure NR, which increased by 42%. For the electrical properties, when the content of MWCNTPDA or MWCNTs is 2 phr, the volume resistivity of NR/MWCNT-PDA composites falls to about 2.7·109 Ω·cm, compared with 3.3·1013 Ω·cm of NR/MWCNT composites. The thermal conductivity of NR composites increased only by 28.2% when 5 phr MWCNT-PDA was added. A model proposed by Nan was used to calculate the thermal conductivity of NR/MWCNT composites, and the calculated values were compared with the experimental values, the results showed that the interface thermal resistance is the main reason why MWCNTs could not significantly increase the thermal conductivity of natural rubber.

  18. Electron beam crosslinked gels-Preparation, characterization and their effect on the mechanical, dynamic mechanical and rheological properties of rubbers

    International Nuclear Information System (INIS)

    Mitra, Suman; Chattopadhyay, Santanu; Sabharwal, Sunil; Bhowmick, Anil K.

    2010-01-01

    Electron beam (EB) crosslinked natural rubber (NR) gels were prepared by curing NR latex with EB irradiation over a range of doses from 2.5 to 20 kGy using butyl acrylate as sensitizer. The NR gels were systematically characterized by solvent swelling, dynamic light scattering, mechanical and dynamic mechanical properties. These gels were introduced in virgin NR and styrene butadiene rubber (SBR) matrices at 2, 4, 8 and 16 phr concentration. Addition of the gels improved the mechanical and dynamic mechanical properties of NR and SBR considerably. For example, 16 phr of 20 kGy EB-irradiated gel-filled NR showed a tensile strength of 3.53 MPa compared to 1.85 MPa of virgin NR. Introduction of gels in NR shifted the glass transition temperature to a higher temperature. A similar effect was observed in the case of NR gel-filled SBR systems. Morphology of the gel-filled systems was studied with atomic force microscopy. The NR gels also improved the processability of the virgin rubbers greatly. Both the shear viscosity and the die swell values of EB-irradiated gel-filled NR and SBR were lower than their virgin counterparts as investigated by capillary rheometer.

  19. Electron beam crosslinked gels-Preparation, characterization and their effect on the mechanical, dynamic mechanical and rheological properties of rubbers

    Energy Technology Data Exchange (ETDEWEB)

    Mitra, Suman; Chattopadhyay, Santanu [Rubber Technology Centre, Indian Institute of Technology, Kharagpur 721302 (India); Sabharwal, Sunil [Radiation Technology Development Section, Bhabha Atomic Research Center, Trombay, Mumbai 400085 (India); Bhowmick, Anil K., E-mail: anilkb@rtc.iitkgp.ernet.i [Rubber Technology Centre, Indian Institute of Technology, Kharagpur 721302 (India)

    2010-03-15

    Electron beam (EB) crosslinked natural rubber (NR) gels were prepared by curing NR latex with EB irradiation over a range of doses from 2.5 to 20 kGy using butyl acrylate as sensitizer. The NR gels were systematically characterized by solvent swelling, dynamic light scattering, mechanical and dynamic mechanical properties. These gels were introduced in virgin NR and styrene butadiene rubber (SBR) matrices at 2, 4, 8 and 16 phr concentration. Addition of the gels improved the mechanical and dynamic mechanical properties of NR and SBR considerably. For example, 16 phr of 20 kGy EB-irradiated gel-filled NR showed a tensile strength of 3.53 MPa compared to 1.85 MPa of virgin NR. Introduction of gels in NR shifted the glass transition temperature to a higher temperature. A similar effect was observed in the case of NR gel-filled SBR systems. Morphology of the gel-filled systems was studied with atomic force microscopy. The NR gels also improved the processability of the virgin rubbers greatly. Both the shear viscosity and the die swell values of EB-irradiated gel-filled NR and SBR were lower than their virgin counterparts as investigated by capillary rheometer.

  20. The Effect of Rubber Mixing Process on The Curing Characteristics of Natural Rubber

    Directory of Open Access Journals (Sweden)

    Abu Hasan

    2013-04-01

    Full Text Available This research is aimed at studying the relationship between rubber mixing processes and curing characteristics of natural rubber. The curing characteristic analysis was carried out through a natural rubber formula having been masticated and mixed, followed by curing. As many as four mastication methods were finely applied; each respected four sequences of rubber mixing process. In the first method, rubber was masticated for 5 minutes and then rubber chemicals and carbon black N 330 were  simultaneously added. In the second and the third methods, rubber was masticated for 1 minute and then carbon blacks and rubber chemicals were also simultaneously added but using different type of fillers. In the fourth method, rubber was masticated for 3 minutes and then rubber chemicals and carbon black were subsequently added. The additions of rubber chemicals and carbon blacks to the masticated rubber were distinguished by the sequence and time allocated for each mixing process. The carbon blacks were added in two stages by which 10 phr was added first and the remaining 40 phr was added later along with oil. In another method, ratios of the carbon blacks addition (as done in the first  and the second stages were 20:30, 30:20, and 40:10. The examination results showed that rubber mixing process gave an impact on the changes of curing characteristics. They were much affected by the method of carbon black addition. The mixing temperature also had an effect on both curing time and curing rate in which the higher the mixing temperature, the lower the curing time and curing rate. Vulcanization temperature also affected the curing time and curing rate in which the higher the vulcanization temperature, the lower the curing time and the higher the curing rate. Lastly, particle size of carbon black also gave an impact on the curing time and curing rate in which the smaller the particle size, the lower the curing time and the higher the curing rate.