Single session of Nd:YAG laser intracanal irradiation neutralizes endotoxin in dental root dentin

Science.gov (United States)

Archilla, José R. F.; Moreira, Maria S. N. A.; Miyagi, Sueli P. H.; Bombana, Antônio C.; Gutknecht, Norbert; Marques, Márcia M.

2012-11-01

Endotoxins released in the dental root by Gram-negative microorganisms can be neutralized by calcium hydroxide, when this medication is applied inside the root canal for at least seven days. However, several clinical situations demand faster root canal decontamination. Thus, for faster endotoxin neutralization, endodontists are seeking additional treatments. The in vitro study tested whether or not intracanal Nd:YAG laser irradiation would be able to neutralize endotoxin within the human dental root canal in a single session. Twenty-four human teeth with one root were mounted between two chambers. After conventional endodontic treatment, root canals were contaminated with Escherichia coli endotoxin. Then they were irradiated or not (controls) in contact mode with an Nd:YAG laser (1.5 W, 15 Hz, 100 mJ and pulse fluency of 124 J/cm2). The endotoxin activity was measured using the limulus lysate technique and data were statistically compared (p≤0.05). The concentration of active endotoxin measured in the negative control group was significantly lower than that of the positive control group (p=0.04). The concentrations of endotoxin in both irradiated groups were significantly lower than that of the positive control group (p=0.027) and similar to that of negative control group (p=0.20). A single session of intracanal Nd:YAG laser irradiation is able to neutralize endotoxin in the dental root tissues.

In vitro evaluation of the morphologic changes on the root dentine irradiated by CO2 laser associated or not to calcium hydroxide application

International Nuclear Information System (INIS)

Romano, Ana Cristina Cury Camargo

2003-01-01

This in vitro study has evaluated the structural changes on the root dentine irradiated by a CO 2 laser associated or not to calcium hydroxide application, from the irradiated surface analysis by means of Scanning Electronic Microscopy (SEM). The purpose of this evaluation has been the study of an alternative method for the treatment of dentine hypersensitivity. Fourteen human teeth were utilized, third molars, divided into 7 groups. Group I (control group) to which no treatment was applied; Groups II, III and IV were given an application of Ca (OH) 2 paste followed by C0 2 laser irradiation, lasting 5 seconds each with intervals of 10 seconds between each application, with continuous emission, power of 0.5 W (Group II), 1.0 W (Group III), and 1.5 W (Group IV); Groups V, VI, and VII were given laser irradiations without the Ca (OH) 2 paste following the same parameters applied to groups II, III, and IV respectively. Morphologic changes suggesting to fusion and re-solidification have been observed, as well as the presence of material obstructing the whole analyzed surface on groups II, III, and IV (laser + Ca (OH) 2 ). As for groups V, VI, and VII, it has been observed fusion, re-solidification, and cracks, and these results being statistically significant when compared the '(Ca (OH) 2 )' groups to the laser groups. No statistically significant differences were observed regarding the different powers applied in the groups that used the same treatment. Despite this result, it can be stated that powers above 1.0 W (DP = 125,38 W/cm 2 ) are unfavorable due to the undesirable morphologic alterations and aesthetic compromising. (author)

Effect of photoactivated riboflavin on the biodegradation-resistance of root-dentin collagen.

Science.gov (United States)

Priyadarshini, Balasankar Meera; Lu, Thong Beng; Fawzy, Amr S

2017-12-01

This study was conducted to evaluate the effect of UVA-activated 1% riboflavin solution on structural integrity; mechanical properties and stability; and collagenase-mediated collagen solubilisation resistance of demineralized root dentin collagen matrix. Root dentin specimens demineralized with 17% EDTA for 7days were treated with 1% RF for 1min followed by UVA photo-activation at intensity 7mW/cm 2 for 1min. Control specimens were completely devoid of riboflavin and/or UVA treatments. Specimens were challenged with bacterial collagenase type-I solution for different time-periods at 37°C. Collagen solubilisation resistance was evaluated in terms of hydroxyproline (HYP) liberation. Mechanical characterization of dentin specimens before and after 24h of exposure to collagenase solution was done in terms of apparent-elastic modulus (E appr ) and ultimate tensile strength (UTS). Variations in dentin collagen-network structure with exposure time in collagenase were visualized by TEM. Crosslinking dentin with UVA-activated riboflavin significantly decreased HYP release and increased E appr and UTS compared to control specimens with storage time in collagenase. Moreover, crosslinked specimens showed higher structural resistance to collagenase effect reflected from dense, well-formed collagen fibrils-network with characteristic collagen cross-banding. UVA-activated riboflavin treatment increased collagenase-mediated collagen degradation resistance and enhanced mechanical stability against collagenase challenges of root dentin after EDTA demineralization. Copyright © 2017 Elsevier B.V. All rights reserved.

Incidence of dentinal defects after root canal preparation: reciprocating versus rotary instrumentation.

Science.gov (United States)

Bürklein, Sebastian; Tsotsis, Polymnia; Schäfer, Edgar

2013-04-01

The purpose of this study was to evaluate the incidence of dentinal defects after root canal preparation with reciprocating instruments (Reciproc and WaveOne) and rotary instruments. One hundred human central mandibular incisors were randomly assigned to 5 groups (n = 20 teeth per group). The root canals were instrumented by using the reciprocating single-file systems Reciproc and WaveOne and the full-sequence rotary Mtwo and ProTaper instruments. One group was left unprepared as control. Roots were sectioned horizontally at 3, 6, and 9 mm from the apex and evaluated under a microscope by using 25-fold magnification. The presence of dentinal defects (complete/incomplete cracks and craze lines) was noted and analyzed by using the chi-square test. No defects were observed in the controls. All canal preparation created dentinal defects. Overall, instrumentation with Reciproc was associated with more complete cracks than the full-sequence files (P = .021). Although both reciprocating files produced more incomplete cracks apically (3 mm) compared with the rotary files (P = .001), no statistically significant differences were obtained concerning the summarized values of all cross sections (P > .05). Under the conditions of this study, root canal preparation with both rotary and reciprocating instruments resulted in dentinal defects. At the apical level of the canals, reciprocating files produced significantly more incomplete dentinal cracks than full-sequence rotary systems (P < .05). Copyright © 2013 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Mineral content analysis of root canal dentin using laser-induced breakdown spectroscopy

Science.gov (United States)

2018-01-01

Objectives This study aimed to introduce the use of laser-induced breakdown spectroscopy (LIBS) for evaluation of the mineral content of root canal dentin, and to assess whether a correlation exists between LIBS and scanning electron microscopy/energy dispersive spectroscopy (SEM/EDS) methods by comparing the effects of irrigation solutions on the mineral content change of root canal dentin. Materials and Methods Forty teeth with a single root canal were decoronated and longitudinally sectioned to expose the canals. The root halves were divided into 4 groups (n = 10) according to the solution applied: group NaOCl, 5.25% sodium hypochlorite (NaOCl) for 1 hour; group EDTA, 17% ethylenediaminetetraacetic acid (EDTA) for 2 minutes; group NaOCl+EDTA, 5.25% NaOCl for 1 hour and 17% EDTA for 2 minutes; a control group. Each root half belonging to the same root was evaluated for mineral content with either LIBS or SEM/EDS methods. The data were analyzed statistically. Results In groups NaOCl and NaOCl+EDTA, the calcium (Ca)/phosphorus (P) ratio decreased while the sodium (Na) level increased compared with the other groups (p LIBS and SEM/EDS analyses (r = 0.84, p LIBS method proved to be reliable while providing data for the elemental composition of root canal dentin. PMID:29487841

Microstructure and wettability of root canal dentine and root canal filling materials after different chemical irrigation

International Nuclear Information System (INIS)

Antonijevic, Djordje; Milovanovic, Petar; Brajkovic, Denis; Ilic, Dragan; Hahn, Michael; Amling, Michael; Rakocevic, Zlatko; Djuric, Marija; Busse, Björn

2015-01-01

Graphical abstract: - Highlights: • Different irrigation solutions and disinfectants were used for treatment of root canal dentine and gutta-percha points. • Materials surface characteristics were assessed using quantitative backscattered electron imaging, reference point indentation, and contact angle analyzer. • The most significant differences in mineralization, indentation, and adhesive outcomes were observed after ethylenediaminetetraacetic acid treatment. • Irrigation solutions confer to superior sealing ability of endodontic filling materials. • Micromechanical characteristics of dentine after irrigation are considerable reduced. - Abstract: The objective of this study was to determine the effects of various irrigation solutions on root canal dentine and gutta-percha surface properties. In addition, the effects of disinfectant chemicals on the wettability and surface morphological properties of the filling materials were evaluated. Ethylenediaminetetraacetic acid (EDTA), citric acid, and ozone were employed as irrigation solutions for dentine and gutta-percha treatment. Thereafter, the samples’ microstructure, degree of mineralization, and mechanical properties were assessed by means of quantitative backscattered electron imaging (qBEI) and reference point indentation (RPI). A contact angle analyzer was used to measure adhesion on the tested materials. Here, EDTA had the most significant affect on both the mechanical properties and the adhesive behavior of dentine. Citric acid did not affect dentine wettability, whereas the indentation properties and the mineralization were reduced. Similar effects were observed when ozone was used. The dentinal tubules were significantly widened in citric acid compared to the ozone group. EDTA causes considerable micromechanical surface alteration of dentine and gutta-percha, but represents the best option in clinical cases where a high adhesiveness of the filling materials is desired.

Microstructure and wettability of root canal dentine and root canal filling materials after different chemical irrigation

Energy Technology Data Exchange (ETDEWEB)

Antonijevic, Djordje; Milovanovic, Petar [Laboratory for Anthropology, Institute for Anatomy, Faculty of Medicine, University of Belgrade, Belgrade (Serbia); Brajkovic, Denis [Department of Dentistry, Faculty of Medical Sciences, University of Kragujevac, Kragujevac (Serbia); Ilic, Dragan [Department of Restorative Medicine, School of Dental Medicine, University of Belgrade, Belgrade (Serbia); Hahn, Michael; Amling, Michael [Department of Osteology and Biomechanics (IOBM), University Medical Center Hamburg-Eppendorf, Lottestr. 55A, 22529 Hamburg (Germany); Rakocevic, Zlatko [Laboratory for Atomic Physics, Institute for Nuclear Science “Vinca”, University of Belgrade, Belgrade (Serbia); Djuric, Marija [Laboratory for Anthropology, Institute for Anatomy, Faculty of Medicine, University of Belgrade, Belgrade (Serbia); Busse, Björn, E-mail: b.busse@uke.uni-hamburg.de [Department of Osteology and Biomechanics (IOBM), University Medical Center Hamburg-Eppendorf, Lottestr. 55A, 22529 Hamburg (Germany)

2015-11-15

Graphical abstract: - Highlights: • Different irrigation solutions and disinfectants were used for treatment of root canal dentine and gutta-percha points. • Materials surface characteristics were assessed using quantitative backscattered electron imaging, reference point indentation, and contact angle analyzer. • The most significant differences in mineralization, indentation, and adhesive outcomes were observed after ethylenediaminetetraacetic acid treatment. • Irrigation solutions confer to superior sealing ability of endodontic filling materials. • Micromechanical characteristics of dentine after irrigation are considerable reduced. - Abstract: The objective of this study was to determine the effects of various irrigation solutions on root canal dentine and gutta-percha surface properties. In addition, the effects of disinfectant chemicals on the wettability and surface morphological properties of the filling materials were evaluated. Ethylenediaminetetraacetic acid (EDTA), citric acid, and ozone were employed as irrigation solutions for dentine and gutta-percha treatment. Thereafter, the samples’ microstructure, degree of mineralization, and mechanical properties were assessed by means of quantitative backscattered electron imaging (qBEI) and reference point indentation (RPI). A contact angle analyzer was used to measure adhesion on the tested materials. Here, EDTA had the most significant affect on both the mechanical properties and the adhesive behavior of dentine. Citric acid did not affect dentine wettability, whereas the indentation properties and the mineralization were reduced. Similar effects were observed when ozone was used. The dentinal tubules were significantly widened in citric acid compared to the ozone group. EDTA causes considerable micromechanical surface alteration of dentine and gutta-percha, but represents the best option in clinical cases where a high adhesiveness of the filling materials is desired.

Effect of Peracetic Acid as A Final Rinse on Push Out Bond Strength of Root Canal Sealers to Root Dentin.

Science.gov (United States)

Gaddala, Naresh; Veeramachineni, Chandrasekhar; Tummala, Muralidhar

2015-05-01

Smear layer which was formed during the instrumentation of root canals hinders the penetration of root canal sealers to root dentin and affect the bond strength of root canal sealers to root dentin. Final irrigant such as demineralizing agents are used to remove the inorganic portion of the smear layer. In the present study, peracetic acid used as a final rinse, to effect the bond strength of root canal sealers to root dentin. The purpose of the present study was to evaluate the efficacy of peracetic acid as a final irrigant on bond strength of root canal sealers to root dentin. Sixty six freshly extracted human single rooted mandibular premolars were used for this study. After decoronation the samples were instrumented with Protaper upto F3 and irrigated with 5.25% NaOcl. The teeth were then divided into three groups based on final irrigant used: Group-1(control group) Canals were irrigated with distilled water. Group-2: Canals were irrigated with peracetic acid. Group-3: Canals were irrigated with smear clear. Each group was further divided into three subgroups (n=30) based on the sealer used to obturate the canals. Subgroup-1: kerr, Subgroup-2: Apexit plus, Subgroup-3: AH PLUS. Each sealer was mixed and coated to master cone and placed in the canal. The bonding between sealer and dentin surface was evaluated using push out bond strength by universal testing machine. The mean bond strength values of each group were statistically evaluated using Two-way ANOVA followed by Tukey post-hoc test. Significant difference was found among the bond strength of the sealers. But, there is no statistically significant difference between the groups irrigated with peracetic acid and smear clear compared to control group. AH Plus showed highest bond strength irrespective of the final irrigant used. Peracetic acid when employed as final irrigant improved the bond strength of root canal sealers compared to control group but not statistically significant than smear clear.

Effect of final irrigation protocols on microhardness reduction and erosion of root canal dentin

Directory of Open Access Journals (Sweden)

Flávia Emi Razera BALDASSO

2017-05-01

Full Text Available Abstract This study aimed to evaluate the effect of final irrigation protocols on microhardness reduction and erosion of root canal dentin. Sixty root canals from mandibular incisors were instrumented and randomly divided into six groups (n = 10 according to the irrigant used: QMiX, 17% EDTA, 10% citric acid (CA, 1% peracetic acid (PA, 2.5% NaOCl (solution control, and distilled water (negative control. The chelating solutions were used to irrigate the canal followed by 2.5% NaOCl as a final flush. After the irrigation protocols, all specimens were rinsed with 10 mL of distilled water to remove any residue of the chemical solutions. Before and after the final irrigation protocols, dentin microhardness was measured with a Knoop indenter. Three indentations were made at 100 µm and 500 µm from the root canal lumen. Afterwards, the specimens were prepared for scanning electron microscopic analysis and the amount of dentin erosion was examined. Wilcoxon and Kruskal-Wallis tests were used to analyze the results with a significance level set at 5%. At 100 µm, all protocols significantly reduced dentin microhardness (p < .05, while at 500 µm, this effect was detected only in the EDTA and QMiX groups (p < .05. CA was the irrigant that caused more extensive erosion in dentinal tubules, followed by PA and EDTA. QMiX opened dentinal tubules, but did not cause dentin erosion. Results suggest that QMiX and 17% EDTA reduced dentin microhardness at a greater depth. Additionally, QMiX did not cause dentin erosion.

Assessment of radicular dentin permeability after irradiation with CO2 laser and endodontic irrigation treatments with thermal imaging

Science.gov (United States)

Cho, Heajin; Lee, Robert C.; Chan, Kenneth H.; Fried, Daniel

2017-02-01

Previous studies have demonstrated that the permeability changes due to the surface modification of dentin can be quantified via thermal imaging during dehydration. The CO2 laser has been shown to remove the smear layer and disinfect root canals. Moreover, thermal modification via CO2 laser irradiation can be used to convert dentin into a highly mineralized enamel-like mineral. The purpose of this study is to evaluate the radicular dentin surface modification after CO2 laser irradiation by measuring the permeability with thermal imaging. Human molar specimens (n=12) were sectioned into 4 axial walls of the pulp chamber and treated with either 10% NaClO for 1 minute, 5% EDTA for 1 minute, CO2 laser or none. The CO2 laser was operated at 9.4 μm with a pulse duration of 26 μs, pulse repetition rate of 300 Hz and a fluence of 13 J/cm2. The samples were dehydrated using an air spray for 60 seconds and imaged using a thermal camera. The resulting surface morphological changes were assessed using 3D digital microscopy. The images from digital microscopy confirmed melting of the mineral phase of dentin. The area enclosed by the time-temperature curve during dehydration, ▵Q, measured with thermal imaging increased significantly with treatments with EDTA and the CO2 laser (Ptreatment increases permeability of radicular dentin.

Direct linear measurement of root dentin thickness and dentin volume changes with post space preparation: A cone-beam computed tomography study

Directory of Open Access Journals (Sweden)

Shoeb Yakub Shaikh

2018-01-01

Full Text Available Aim: The purpose of the present study was direct linear measurement of dentin thickness and dentin volume changes for post space preparation with cone-beam computed tomography (CBCT. Materials and Methods: Ten maxillary central incisors were scanned, before and after root canal and post space preparation, with Orthophos XG three-dimensional hybrid unit. Thirteen axial section scans of each tooth from orifice to apex and dentin thickness for buccal, lingual, mesial, and distal were measured using proprietary measuring tool and thereafter subjected to statistical analysis. Furthermore, dentin volume was evaluated using ITK-SNAP software. Results: There was statistically significant difference between the dentin thickness in pre- and postinstrumentation (paired t-test and also between different groups (one-way ANOVA. In the shortest post length of 4.5mm the post space preparation resulted in 2.17% loss of hard tissue volume, where as 11mm longest post length post space preparation resulted in >40% loss of hard tissue volume. Conclusion: CBCT axial section scan for direct measurements of root dentin thickness can be guideline before and after post space preparation for selection of drill length and diameter.

Optothermal transfer simulation in laser-irradiated human dentin.

Science.gov (United States)

Moriyama, Eduardo H; Zangaro, Renato A; Lobo, Paulo D C; Villaverde, Antonio Balbin; Pacheco, Marcos T; Watanabe, Ii-Sei; Vitkin, Alex

2003-04-01

Laser technology has been studied as a potential replacement to the conventional dental drill. However, to prevent pulpal cell damage, information related to the safety parameters using high-power lasers in oral mineralized tissues is needed. In this study, the heat distribution profiles at the surface and subsurface regions of human dentine samples irradiated with a Nd:YAG laser were simulated using Crank-Nicolson's finite difference method for different laser energies and pulse durations. Heat distribution throughout the dentin layer, from the external dentin surface to the pulp chamber wall, were calculated in each case, to investigate the details of pulsed laser-hard dental tissue interactions. The results showed that the final temperature at the pulp chamber wall and at the dentin surface are strongly dependent on the pulse duration, exposure time, and the energy contained in each pulse.

Dentinal hypersensitivity following scaling and root planing: comparison of low-level laser and topical fluoride treatment.

Science.gov (United States)

Pesevska, Snezana; Nakova, Marija; Ivanovski, Kiro; Angelov, Nikola; Kesic, Ljiljana; Obradovic, Radmila; Mindova, Sonja; Nares, Salvador

2010-09-01

The aim of this study is to compare the effectiveness of low-level laser irradiation to traditional topical fluoride treatment for treatment choices of dentinal hypersensitivity following scaling and root planing. The experimental group (15 patients) was treated with low-energy-level diode laser at each site of dentinal hypersensitivity following scaling and root planning. The control group (15 patients) received topical fluoride treatment (protective varnish for desensitization). All the patients were treated at baseline visit, and then at day 2 and 4 after the initial treatment; the pain was subjectively assessed by the patients as strong, medium, medium low, low, or no pain. Total absence of the dental hypersensitivity was reported in 26.66% of the examined group even after the second visit, compared to the control group where complete resolution of the hypersensitivity was not present after the second visit in any of the treated cases. Complete absence of pain was achieved in 86.6% of patients treated with laser and only in 26.6% in the fluoride treated group, after the third visit. Based on our findings, we conclude that low-energy biostimulative laser treatment can be successfully used for treatment of dental hypersensitivity following scaling and root planing.

Electron probe study of human and red deer cementum and root dentin

Energy Technology Data Exchange (ETDEWEB)

Toetdal, B. (Department of Physics, University of Trondheim, The Norwegian Institute of Technology); Hals, E. (Department of Cariology and Endodontics, Faculty of Odontology, University of Bergen, Norway)

1985-01-01

A topographical description of the concentration profiles of Ca, P, Mg, Zn, F, S, and K in human and red deer cementum and root dentin is given. The concentrations reported should be regarded as semiquantitative values. A downward slope of the Ca, P, and Mg profiles toward the pulpal cavity seemed largely to correspond with the secondary dentin. Marked elevations of the Zn profiles, modest elevations of the F profiles, and in a few instances of the S profiles, toward root surface and pulpal cavity were registered. In a couple of scans a slight elevation of the K profile toward the root surface was observed. A high degree of concordance in human and red deer teeth was ascertained.

Vitality of Enterococcus faecalis inside dentinal tubules after five root canal disinfection methods.

Science.gov (United States)

Vatkar, Niranjan Ashok; Hegde, Vivek; Sathe, Sucheta

2016-01-01

To compare the vitality of Enterococcus faecalis within dentinal tubules after subjected to five root canal disinfection methods. Dentin blocks (n = 60) were colonized with E. faecalis. After 4 weeks of incubation, the dentin blocks were divided into one control and five test groups (n = 10 each). The root canals of test groups were subjected to one of the disinfection methods, namely, normal saline (NS), sodium hypochlorite (NaOCl), chlorhexidine digluconate (CHX), neodymium-doped yttrium aluminum garnet (Nd: YAG) laser, and diode laser. The effect of disinfection methods was assessed by LIVE/DEAD BacLight stain under the confocal laser scanning microscopy to determine the "zone of dead bacteria" (ZDB). Mean values were calculated for ZDB and the difference between groups was established. Penetration of E. faecalis was seen to a depth of >1000 μm. Viable bacteria were detected with NS irrigation. NaOCl and CHX showed partial ZDB. When the root canals were disinfected with Nd: YAG and diode lasers, no viable bacteria were found. E. faecalis has the ability to colonize inside dentinal tubules to a depth of >1000 μm. In contrast to conventional irrigants, both Nd: YAG and diode lasers were effective in eliminating the vitality of E. faecalis. NS, NaOCl, and CHX showed viable bacteria remaining in dentinal tubules.

Evaluation in vitro of effects of Er:YAG and Nd:YAG lasers irradiation on root canal wall, by stereoscopy, scanning electron micrography and thermographic camera

International Nuclear Information System (INIS)

Goya, Claudia

2001-01-01

This study was carried out to evaluate in vitro the effects of Nd:YAG laser and Er:YAG laser irradiation in the root canal wall by SEM, evaluating the apical leakage and the temperature changes during the laser irradiation. Seventy four extracted human teeth were used, they were instrumented and divided into seven groups of 10 teeth each. The teeth were evaluated through stereoscopy, by SEM, and with the thermographic camera. The Nd:YAG laser irradiation parameters were 100 mJ/p, 15 Hz, and Er:YAG laser were 160 mJ/p and 10 Hz, the irradiation was 4 times at 2 mm/sec speed, with 20 sec interval. The apical leakage was not observed in the teeth irradiated by Nd:YAG laser alone or in association with Er:YAG laser. However in the teeth irradiated only by the Er:YAG laser we observed a little leakage. By SEM observation the Nd:YAG laser irradiation showed melting and recrystallization in the dentin surface closing dentinal tubules, and in the samples irradiated by Er:Y AG laser a clean surface, opened dentinal tubules, and the combination by two lasers, showed melting covering some dentinal tubules The thermographic study found the temperature increase was not more than 6 deg C. This study showed the safety parameters applications of Er:YAG laser in association with Nd:YAG laser in root canal treatment, in order to not cause thermal damages to the periodontal tissues. (author)

Structure and composition of enamel and dentin after thermal treatment or infrared laser irradiation

International Nuclear Information System (INIS)

Bachmann, Luciano

2004-01-01

The main purpose of this work is to identify the crystallographic structure, optical properties, chemical composition and electron paramagnetic signals that laser irradiation or oven heating produces on the tissue. The thermal treatment was conducted in oven with temperature range below 1000 deg C and the laser irradiation with holmium (Ho:YLF - 2,065 μm) and erbium (Er:YAG - 2,94 μm) laser. The tissue characterization was carried out with X-ray diffraction, scanning electron microscopy, ultraviolet and visible transmission spectroscopy, light microscopy, infrared transmission/reflection spectroscopy and electron paramagnetic resonance. The holmium irradiated enamel (600-800 J/cm 2 ) shows the presence of tetracalcium phosphate that coexists with the natural phase (hydroxyapatite). The irradiated dentin shows only the sharper diffraction peaks of the natural phase. The narrows peaks, observed after irradiation, could be assigned to the dentin crystal growth and impurities elimination. Tissue discoloration is observed after thermal treatment with temperatures above 100 deg C. Heated enamel become white-opaque and the origin is assigned to the water elimination, which promotes higher light scattering by the prismatic structure. On the other hand, heated dentin, with similar temperatures becomes brown. The dentin browning changes with the temperature and shown two peaks, at 375 deg C and 700 deg C. The peak at 375 deg C is assigned to the collagen structure degradation and at 700 deg C to the cyanate formation. The dentin discoloration produced with temperatures below 200 deg C is reversible after the tissue hydration. Both enamel and dentin discoloration are also observed in erbium irradiated tissues. Thermal treatments, heating in oven or laser irradiation, change mainly the organic matrix composition and water present in the tissues. The inorganic matrix is more stable and its radicals are changed, with more predominance, only at temperatures higher than 500 deg

Failure of root development of human permanent teeth following irradiation

International Nuclear Information System (INIS)

Takeda, Yasunori; Kuroda, Masafumi; Amari, Eiichi; Yanagisawa, Toru

1987-01-01

Complete absence of root formation of the upper incisors, canine and first premolar was reported in a 27-year-old female who had received radiation therapy for a retinal glioma of the right eye at age of 3 years 1 month. Ground and decalcified sections showed no remarkable changes in enamel and dentin of the crowns, but the pulp floor was closed by irregular dentin deposit despite the absence of root formation. The outer surface of the irregular dentin was covered by acellular cementum, and the periodontal membrane was undeveloped. A slight degree of fibrosis was seen in the pulp, but the coronal part of the dentin was lined by odontoblasts. The theory that tooth eruption is caused by the growth of the root is not substantiated by the observation in this case. (author)

Effect of x-ray irradiation on the dentin matrix formation

Energy Technology Data Exchange (ETDEWEB)

You, Dong Soo [Dept. of Radiology, College of Dentistry, Seoul National University, Seoul (Korea, Republic of); Chang, Won Sik [Dept. of Prosthodontics, College of Dentistry, Seoul National University, Seoul (Korea, Republic of); Whang, Sung Myung [Dept. of Oral Antomy, College of Dentistry, Seoul National University, Seoul (Korea, Republic of)

1976-11-15

The authors has observed the effect of X-ray irradiation on the dentin matrix formation of the albino rat fetuses. The lower abdomen of the pregnant rats were exposed to X-ray on the 9 1/2th day of gestation, respectively 150, 250 and 350 rads. The fetuses of the right side of the same pregnant rats which were not exposed to X-ray were as controls. The results were as follows: 1) In the 150 rads irradiated fetuses, predentin formation was identical with control groups, but the arrangement of od ontoblasts was distorted, subodontoblastic layer was condensed with pulp cells, and blood capillaries were enlarged. 2) In the 250 rads irradiation, dentin matrix was imperfect or osteodentin was occurred. Short columnar or cuboidal od ontoblasts were presented and pulp cells were dispersed. Blood capillaries were congested. 3) 350 rads irradiated fetuses showed osteodentin matrix and numerous degenerated odontoblasts. Their dental papilla sh owed reticular atrophy and enlarged capillary.

Mathematical simulation of the thermal diffusion in dentine irradiated with Nd:YAG laser using finite difference method

Science.gov (United States)

Moriyama, Eduardo H.; Zangaro, Renato A.; Lobo, Paulo D. d. C.; Villaverde, Antonio G. J. B.; Watanabe-Sei, Ii; Pacheco, Marcos T. T.; Otsuka, Daniel K.

2002-06-01

Thermal damage in dental pulp during Nd:YAG laser irradiation have been studied by several researchers; but due to dentin inhomogeneous structure, laser interaction with dentin in the hypersensitivity treatment are not fully understood. In this work, heat distribution profile on human dentine samples irradiated with Nd:YAG laser was simulated at surface and subjacent layers. Calculations were carried out using the Crank-Nicolson's finite difference method. Sixteen dentin samples with 1,5 mm of thickness were evenly distributed into four groups and irradiated with Nd:YAG laser pulses, according to the following scheme: (I) 1 pulse of 900 mJ, (II) 2 pulses of 450 mJ, (III) 3 pulses of 300 mJ, (IV) 6 pulses of 150 mJ; corresponding to a total laser energy of 900 mJ. The pulse interval was 300ms, the pulse duration of 900 ms and irradiated surface area of 0,005 mm2. Laser induced morphological changes in dentin were observed for all the irradiated samples. The heat distribution throughout the dentin layer, from the external dentin surface to the pulpal chamber wall, was calculated for each case, in order to obtain further information about the pulsed Nd:YAG laser-oral hard tissue interaction. The simulation showed significant differences in the final temperature at the pulpal chamber, depending on the exposition time and the energy contained in the laser pulse.

Bond strength of composite to dentin: effect of acid etching and laser irradiation through an uncured self-etch adhesive system

International Nuclear Information System (INIS)

Castro, F L A; Carvalho, J G; Andrade, M F; Saad, J R C; Hebling, J; Lizarelli, R F Z

2014-01-01

This study evaluated the effect on micro-tensile bond strength (µ-TBS) of laser irradiation of etched/unetched dentin through an uncured self-etching adhesive. Dentinal surfaces were treated with Clearfil SE Bond Adhesive (CSE) either according to the manufacturer’s instructions (CSE) or without applying the primer (CSE/NP). The dentin was irradiated through the uncured adhesive, using an Nd:YAG laser at 0.75 or 1 W power settings. The adhesive was cured, composite crowns were built up, and the teeth were sectioned into beams (0.49 mm 2 ) to be stressed under tension. Data were analyzed using one-way ANOVA and Tukey statistics (α = 5%). Dentin of the fractured specimens and the interfaces of untested beams were observed under scanning electron microscopy (SEM). The results showed that non-etched irradiated surfaces presented higher µ-TBS than etched and irradiated surfaces (p < 0.05). Laser irradiation alone did not lead to differences in µ-TBS (p > 0.05). SEM showed solidification globules on the surfaces of the specimens. The interfaces were similar on irradiated and non-irradiated surfaces. Laser irradiation of dentin through the uncured adhesive did not lead to higher µ-TBS when compared to the suggested manufacturer’s technique. However, this treatment brought benefits when performed on unetched dentin, since bond strengths were higher when compared to etched dentin. (paper)

Vertical Root Fracture initiation in curved roots after root canal preparation: A dentinal micro-crack analysis with LED transillumination.

Science.gov (United States)

Miguéns-Vila, Ramón; Martín-Biedma, Benjamín; Varela-Patiño, Purificación; Ruíz-Piñón, Manuel; Castelo-Baz, Pablo

2017-10-01

One of the causative factors of root defects is the increased friction produced by rotary instrumentation. A high canal curvature may increase stress, making the tooth more susceptible to dentinal cracks. The purpose of this study was to evaluate dentinal micro-crack formation with the ProTaper NEXT and ProTaper Universal systems using LED transillumination, and to analyze the micro-crack generated at the point of maximum canal curvature. 60 human mandibular premolars with curvatures between 30-49° and radii between 2-4 mm were used. The root canals were instrumented using the Protaper Universal® and Protaper NEXT® systems, with the aid of the Proglider® system. The obtained samples were sectioned transversely before subsequent analysis with LED transillumination at 2 mm and 8 mm from the apex and at the point of maximum canal curvature. Defects were scored: 0 for no defects; and 1 for micro-cracks. Root defects were not observed in the control group. The ProTaper NEXT system caused fewer defects (16.7%) than the ProTaper Universal system (40%) ( P Universal system caused significantly more micro-cracks at the point of maximum canal curvature than the ProTaper NEXT system ( P Universal system. A higher prevalence of defects was found at the point of maximum curvature in the ProTaper Universal group. Key words: Curved root, Micro-crack, point of maximum canal curvature, ProTaper NEXT, ProTaper Universal, Vertical root fracture.

Anti-dentine antibodies with root resorption during orthodontic treatment.

Science.gov (United States)

Ramos, Solange de Paula; Ortolan, Geórgia Oliveira; Dos Santos, Lívia Marques; Tobouti, Priscila Lie; Hidalgo, Miriam Marubayashi; Consolaro, Alberto; Itano, Eiko Nakagawa

2011-10-01

The aim of this study was to analyse serum IgG levels and salivary secretory IgA (sIgA) levels in human dentine extract (HDE) before (T0) and 6 months after (T6) orthodontic treatment and to correlate anti-HDE autoantibodies to root resorption. Fifty orthodontic patients were selected, 19 males (15.6 ± 8.5 years) and 31 females (21.4 ± 11.2 years), 19 in the mixed dentition (10.3 ± 1.9 years) and 31 in the permanent dentition (24.6 ± 9.9 years). Fifty individuals not undergoing orthodontic treatment matched by gender and age were selected as the controls. Periapical radiographs of the upper central incisors and saliva sampling were obtained of all patients at T0 and T6. Serum samples were collected from the permanent dentition patients (n = 31). Antibody levels were determined by means of immunoenzyme assay. At T6, root resorption was classified as grade 0 (no resorption), grade 1 (slight resorption), and grade 2 (moderate to severe resorption). Differences between antibody levels at T0 and T6 and among different grades of resorption were determined by paired t- and Kruskal-Wallis tests, respectively. Spearman's rank correlation coefficient was applied to detect correlation between sIgA and IgG levels, and logistic regression to determine the association of root resorption grade and the studied variables. Differences were considered significant at P root resorption patients during treatment and was not correlated to salivary sIgA levels or other variables. Patients who had grade 2 root resorption at T6 showed higher levels of anti-HDE sIgA (P root shape were the main factors associated with the degree of root resorption. The results suggest that variations to systemic and local humoural immune response to dentine antigens may occur during orthodontic treatment. High levels of salivary sIgA before treatment were associated with more advanced lesions after 6 months of treatment.

Comparison of Dentinal Crack Formation With Reciproc, Mtwo and ProTaper Root Canal Preparation Systems

Directory of Open Access Journals (Sweden)

Nazari Moghaddam

2016-06-01

Full Text Available Background Instrumentation with rotary instruments could potentially cause dentinal cracks possibly leading to tooth fracture. Reciproc files require a single file to finalize the root canal preparation and the effect of this procedure has not been compared with other systems. Objectives The aim of this study was to compare the incidence of dentinal micro-cracks following root canal preparations with ProTaper, Mtwo and Reciproc files. Materials and Methods In an experimental in vitro trial, 80 maxillary and mandibular first molars were selected and their crowns and distal roots were cut. The roots were then examined to remove any previous cracks and defects. An impression polyether material was used to simulate teeth periodontal ligament (PDL. The teeth were divided to four experimental groups (n = 20 and prepared using Reciproc, Mtwo and ProTaper or remained unprepared as a control group. The specimens were then sectioned horizontally on 3, 5 and 9 mm from the apex and number of micro-cracks was determined by stereomicroscope. The incidence of dentinal cracks on different systems or sections were statistically analyzed by means of the chi-square test. Results Dentinal defects on 3-mm, 5-mm and 9-mm sections from the apex were noted in 10 (5.6%; 7 (3.9% and 9 (5.0% samples of all, respectively. Following canal preparation using Reciproc, ProTaper and Mtwo systems, the defects were observed in 7 (3.9%, 12 (6.7% and 7 (3.9% the sections, respectively. No significant differences were observed regarding the defect incidence on the studied instrumentation files or sections. Conclusions Regarding the study limitations, dentinal cracks were observed in all files and distances from the apex. Although there was more crack incidence in ProTaper files, no significant differences were noted regarding the studied systems and sections from the apex.

Effect of root canal sealer and artificial accelerated aging on fibreglass post bond strength to intraradicular dentin.

Science.gov (United States)

Santana, Fernanda-Ribeiro; Soares, Carlos-José; Ferreira, Josemar-Martins; Valdivi, Andréa-Dolores-Correia-Miranda; Souza, João-Batista-de; Estrela, Carlos

2014-10-01

To evaluate the effect of root canal sealers (RCS) and specimen aging on the bond strength of fibre posts to bovine intraradicular dentin. 80 teeth were used according the groups - Sealapextm, Sealer 26®, AH Plus® and specimens aging - test with no aging and with aging. The canals prepared were filled using one of each RCS. The posts were cemented. Roots were cross-sectioned to obtain two slices of each third. Samples were submitted to push-out test. Failure mode was evaluated under a confocal microscope. The data were analysed by ANOVA, Tukey's, and Dunnet tests (α = 0.05). No significant difference was detected among RCS. Aged control presented higher bond strength than immediate control. The aging did not result significant difference. Adhesive cement-dentin failure was prevalent in all groups. RCS interfered negatively with bonding of fibreglass posts cemented with self-adhesive resin cement to intraradicular dentin. Key words:Fibreglass post, bond strength, root dentin, endodontic sealer, aging.

Inactivation of local root canal medicaments by dentine: an in vitro study.

Science.gov (United States)

Haapasalo, H K; Sirén, E K; Waltimo, T M; Ørstavik, D; Haapasalo, M P

2000-03-01

The aim of the study was to investigate the inactivation by dentine of the antibacterial activity of various commonly used local root canal medicaments. The medicaments tested were saturated calcium hydroxide solution, 1% sodium hypochlorite, 0.5% and 0.05% chlorhexidine acetate, and 2/4% and 0.2/0.4% iodine potassium iodide. Dentine was sterilized by autoclaving and crushed into powder with a particle size of 0.2-20 microns. Aliquots of dentine suspension were incubated with the medicaments in sealed test tubes at 37 degrees C for 24 h or 1 h before adding the bacteria. In some experiments bacteria were added simultaneously with dentine powder and the medicament. Enterococcus faecalis A197A was used as a test organism. Samples for bacterial culturing were taken from the suspensions at 5 min, 1 h and 24 h after adding the bacteria. Dentine powder had an inhibitory effect on all medicaments tested. The effect was dependent on the concentration of the medicament as well as on the length of the time the medicament was preincubated with dentine powder before adding the bacteria. The effect of calcium hydroxide on E. faecalis was totally abolished by the presence of dentine powder. Similarly, 0.2/0.4% iodine potassium iodide lost its effect after preincubation for 1 h with dentine before adding the bacteria. The effect of 0.05% chlorhexidine and 1% sodium hypochlorite on E. faecalis was reduced but not totally eliminated by the presence of dentine. No inhibition could be measured when full strength solutions of chlorhexidine and iodine potassium iodide were used in killing E. faecalis. The dentine powder model appears to be an efficient tool for the study of interactions between local endodontic medicaments, dentine, and microbes.

Marginal adaptation of newer root canal sealers to dentin: A SEM study.

Science.gov (United States)

Polineni, Swapnika; Bolla, Nagesh; Mandava, Pragna; Vemuri, Sayesh; Mallela, Madhusudana; Gandham, Vijaya Madhuri

2016-01-01

This in vitro study evaluated and compared the marginal adaptation of three newer root canal sealers to root dentin. Thirty freshly extracted human single-rooted teeth with completely formed apices were taken. Teeth were decoronated, and root canals were instrumented. The specimens were randomly divided into three groups (n = 10) based upon the sealer used. Group 1 - teeth were obturated with epoxy resin sealer (MM-Seal). Group 2 - teeth were obturated with mineral trioxide aggregate (MTA) based sealer (MTA Fillapex), Group 3 - teeth were obturated with bioceramic sealer (EndoSequence BC sealer). Later samples were vertically sectioned using hard tissue microtome and marginal adaptation of sealers to root dentin was evaluated under coronal and apical halves using scanning electron microscopy (SEM) and marginal gap values were recorded. The data were statistically analyzed by two-way ANOVA and Tukey's multiple post hoc test. The highest marginal gap was seen in Group 2 (apical-16680.00 nm, coronal-10796 nm) and the lowest marginal gap was observed in Group 1 (apical-599.42 nm, coronal-522.72 nm). Coronal halves showed superior adaptation compared to apical halves in all the groups under SEM. Within the limitations of this study epoxy resin-based MM-Seal showed good marginal adaptation than other materials tested.

Thin and thick layers of resin-based sealer cement bonded to root dentine compared: Adhesive behaviour.

Science.gov (United States)

Pane, Epita S; Palamara, Joseph E A; Messer, Harold H

2015-12-01

This study aims to evaluate tensile and shear bond strengths of one epoxy (AH) and two methacrylate resin-based sealers (EZ and RS) in thin and thick layers bonded to root dentine. An alignment device was prepared for accurate positioning of 20 root dentine cylinders in a predefined gap of 0.1 or 1 mm. Sealer was placed in the interface. Bond strength tests were conducted. Mode of failures and representative surfaces were evaluated. Data were analysed using anova and post-hoc tests, with P thick layer of sealer produced higher bond strength, except for the shear bond strength of EZ. Significant differences between thin and thick layers were found only in tensile bond strengths of AH and RS. Mixed type of failure was constantly found with all sealers. Bond strengths of thick layers of resin-based sealers to root dentine tended to be higher than with thin layers. © 2015 Australian Society of Endodontology.

Effect of different diode laser wavelengths on root dentin decontamination infected with Enterococcus faecalis.

Science.gov (United States)

Borges, Caroline Cristina; Estrela, Carlos; Lopes, Fabiane Carneiro; Palma-Dibb, Regina Guenka; Pecora, Jesus Djalma; De Araújo Estrela, Cyntia Rodrigues; Sousa-Neto, Manoel Damião de

2017-11-01

The objective of this study was to evaluate the antibacterial effect and the ultrastructural alterations of diode laser with different wavelengths (808nm and 970nm) and its association with irrigating solutions (2.5% sodium hypochlorite and 2% chlorhexidine) in root dentin contaminated by a five days biofilm. Thirteen uniradicular teeth were sectioned into 100 dentin intraradicular blocks. Initially, the blocks were immersed for 5min in 17% EDTA and washed with distilled water for 5min, then samples were sterilized for 30min at 120°C. The dentin samples were inoculated with 0.1mL of E. faecalis suspension in 5mL BHI (Brain Heart Infusion) and incubated at 37°C for 5days. After contamination, the specimens were distributed into ten groups (n=10) according to surface treatment: GI - 5mL NaOCl 2.5%, GII - 5mL NaOCl 2.5%+808nm diode (0.1W for 20s), GIII - 5mL NaOCl 2.5%+970nm diode (0.5W for 4s), GIV - 808nm diode (0.1W for 20s), GV - 970nm diode (0.5W for 4s), GVI - CHX 2%, GVII - CHX 2%+808nm diode (0.1W for 20s), GVIII - CHX 2%+970nm diode (0.5W for 4s), GIX - positive control and GX - negative control. Bacterial growth was analyzed by turbidity and optical density of the growth medium by spectrophotometry (nm). Then, the specimens were processed for analysis ultrastructural changes of the dentin surface by SEM. The data was subject to the One-way ANOVA test. GI (77.5±12.1), GII (72.5±12.2), GIII (68.7±8.7), GV (68.3±8.7), GVI (62.0±5.5) and GVII (67.5±3.3) were statistically similar and statistically different from GIV (58.8±25.0), GVIII (59.2±4.0) and control groups (pdiode laser; erosion of the intertubular dentin in blocks submitted to 808nm diode laser irradiation; and an increased erosion of the intertubular dentin when 2.5% NaOCl was associated to the different wavelengths lasers. All the therapeutic protocols were able to reduce the bacterial contingent in dentin blocks, and the association of diode laser and solutions did not significantly improve

Efficacy of calcium oxide and calcium hydroxide nanoparticles on the elimination of Enterococcus faecalis in human root dentin.

Science.gov (United States)

Louwakul, Phumisak; Saelo, Attapon; Khemaleelakul, Saengusa

2017-04-01

The objective of this study was to compare the antibacterial effect of calcium oxide nanoparticles (CONPs) and calcium hydroxide nanoparticles (CHNPs) against Enterococcus faecalis in a dentinal block model. E. faecalis strain JCM 7783 was introduced into dentinal tubules of semicylindrical dentin specimens by centrifugation and incubated for 1 week. Fifty microliters of CONPs or CHNPs was placed on the root canal side of the infected dentin specimens. The specimens were then incubated in aerobic condition at 37 °C and 100 % relative humidity for 1 week. The treated dentin specimens were subjected to fluorescent staining and confocal laser scanning microscopy (CLSM) to analyze the proportions of non-vital and vital bacterial cells inside the dentinal tubules. Scanning electron microscopy (SEM) was used to confirm the effect of the medicaments on the bacteria in the dentinal tubules. Calcium oxide (CO) and calcium hydroxide (CH) were used as controls. Based on the CLSM and SEM analyses, CHNPs were more efficient than CONPs in the elimination of the bacteria in the dentinal tubules. CONPs significantly killed more E. faecalis than CO and CH (P < .05). Neither CO nor CH was able to kill the bacteria. CHNPs were more effective than CONPs in the elimination of E. faecalis in dentinal tubules. CHNPs are effective nanoparticles in killing endodontic bacteria present in dentinal tubules. They have potential as an intracanal medicament, which may be beneficial in root canal therapy.

Effect of root canal rinsing protocol on dentin bond strength of two resin cements using three different method of test.

Science.gov (United States)

Khoroushi, Maryam; Sheikhi, Mohammadreza; Khalilian-Gourtani, Amirhossein; Soleimani, Bahram

2016-07-01

Different studies have used different tests to evaluate bond strength of resin cements to root dentin. In this in vitrostudy, three different tests were used to evaluate the bond strength of two resin cements to root dentin using two root dentin irrigation protocols. Ninety-six intact single-rooted teeth were selected for this study. Forty-eight teeth, with a root length of 15mm, were randomly divided into two groups and irrigated with normal saline or 2.5% sodium hypochlorite solutions during root canal preparation, respectively. For each 12 specimens from each group, fiber post #1 was bonded using an etch-and-rinse (Duo-Link) and a self-adhesive (BisCem) resin cement, respectively. After incubation, two specimens were prepared for the push-out test from the middle thirds of the roots. In another 24 teeth, after two 1.5-mm sections were prepared from the middle thirds of the prepared roots, sections of the post were bonded in two subgroups with each of the cements mentioned above and the samples were prepared for the pull-out test. For shear test, the crowns of 48 teeth were cut away, the dentin surfaces were prepared, the two irrigation solutions were used, and the resin cements were bonded. Data collected from the three tests were evaluated by ANOVA, post-hoc Tukey and Weibull tests (α=0.05). There were significant differences in the mean bond strength values between the three bond strength tests (Pstrength in all tests (P>0.05). Under the limitations of the present study, the method of the test used had an effect on the recorded bond strength between the resin cement and root dentin. Cement type and irrigation protocol resulted in similar variations with all the tests. Push-out and shear tests exhibited more coherent results. Bond strength, endodontically treated tooth, fiber post, resin cement, sodium hypochlorite.

In vitro evaluation of the contact angle formed between AH Plus, Hybrid Root Seal and mineral trioxide aggregate Plus sealer with dentin and gutta-percha.

Science.gov (United States)

Nikhil, Vineeta; Jaiswal, Shikha; Bajpai, Gauravi

2018-01-01

The purpose of this study was evaluation and comparison of the contact angle of new root canal sealers - Hybrid Root Seal, mineral trioxide aggregate (MTA) Plus, and the conventional AH Plus sealer with dentin and gutta-percha. Two groups (Group D - dentin and Group G - gutta-percha) of 18 samples each were further randomly divided into 3 subgroups based on the type of sealer used, that is, AH Plus, Hybrid Root Seal, and MTA Plus. Contact angle measurement device (Phoenix 300) was used to measure the contact angle of the sealers on both dentin and gutta-percha. The results thus obtained were analyzed using one-way analysis of variance and Student's t -test. MTA Plus recorded significantly higher values of contact angle on both the substrates, that is, dentin and gutta-percha when compared to AH Plus and Hybrid root canal sealer. The lowest value of contact angle in gutta-percha and dentin was shown by Hybrid root canal sealer and AH Plus, respectively. Both AH Plus and Hybrid Root Seal exhibited lower contact angle values, and hence, better wettability on both dentin and gutta-percha as compared to MTA Plus.

Effect of LASER Irradiation on the Shear Bond Strength of Zirconia Ceramic Surface to Dentin

Directory of Open Access Journals (Sweden)

Sima Shahabi

2012-09-01

Full Text Available Background and Aims: Reliable bonding between tooth substrate and zirconia-based ceramic restorations is always of great importance. The laser might be useful for treatment of ceramic surfaces. The aim of the present study was to investigate the effect of laser irradiation on the shear bond strength of zirconia ceramic surface to dentin. Materials and Methods: In this experimental in vitro study, 40 Cercon zirconia ceramic blocks were fabricated. The surface treatment was performed using sandblasting with 50-micrometer Al2O3, CO2 laser, or Nd:YAG laser in each test groups. After that, the specimens were cemented to human dentin with resin cement. The shear bond strength of ceramics to dentin was determined and failure mode of each specimen was analyzed by stereo-microscope and SEM investigations. The data were statistically analyzed by one-way analysis of variance and Tukey multiple comparisons. The surface morphology of one specimen from each group was investigated under SEM. Results: The mean shear bond strength of zirconia ceramic to dentin was 7.79±3.03, 9.85±4.69, 14.92±4.48 MPa for CO2 irradiated, Nd:YAG irradiated, and sandblasted specimens, respectively. Significant differences were noted between CO2 (P=0.001 and Nd:YAG laser (P=0.017 irradiated specimens with sandblasted specimens. No significant differences were observed between two laser methods (P=0.47. The mode of bond failure was predominantly adhesive in test groups (CO2 irradiated specimens: 75%, Nd:YAG irradiated: 66.7%, and sandblasting: 41.7%. Conclusion: Under the limitations of the present study, surface treatment of zirconia ceramics using CO2 and Nd:YAG lasers was not able to produce adequate bond strength with dentin surfaces in comparison to sandblasting technique. Therefore, the use of lasers with the mentioned parameters may not be recommended for the surface treatment of Cercon ceramics.

Evaluation of inactivation of intracanal antiseptics by dentin, demineralized dentin, dentin matrix and mineral component of dentin

Directory of Open Access Journals (Sweden)

Razmi H

2007-01-01

Full Text Available Background and Aim: Many studies have shown that microorganisms are the main cause of pulpal diseases and the main purpose of root canal therapy is their elimination from the root canal system. Antiseptic agents are used to reduce bacteria but their antibacterial activities differ from in vivo to in vitro studies and might be inactivated by dentin and its components in root canal space. This study was designed to investigate the effect of dentin on antibacterial activity of different antimicrobial agents. Materials and Methods: In this experimental study, two antibacterial agents (sodium hypochlorite and chlorhexidine with different concentrations were used in four experimental groups: Group 1: dentin, Group 2: demineralized dentin with EDTA, Group 3: dentin matrix and Group 4: dentin mineral component. The species used in this study was Entrococcus faecalis. Different concentration of agents were added to mixture of each experimental group and bacteria. At the baseline and after one and 24 hours, samples were collected and cultured. After incubation period, colonies were counted. Data were analyzed by Tukey test with p<0.05 as the limit of significance. Results: 2% and 0.2% chlorhexidine, and 5% sodium hypochlorite solutions at the three studied times eliminated Entrococcus faecalis completely. 1% sodium hypochlorite eliminated all bacteria in 1h and 24 hs. Statistical analysis showed significant differences between experimental and control groups (P<0.05. Sodium 1% hypochlorite at time 0, could reduce bacteria significantly (P<0.05 but didn’t eliminate them completely. Conclusion: Inactivation of intracanal antiseptics was not observed in this study. As elimination of bacteria occurred, application of these antibacterial agents are recommended in endodontic treatment. Further investigations on other antibacterial agents, other concentrations and shorter time intervals are recommended.

Microtensile bond strength of etch-and-rinse and self-etching adhesives to intrapulpal dentin after endodontic irrigation and setting of root canal sealer.

Science.gov (United States)

Wattanawongpitak, Nipaporn; Nakajima, Masatoshi; Ikeda, Masaomi; Foxton, Richard M; Tagami, Junji

2009-02-01

To evaluate the effect of endodontic irrigation regimens and calcium hydroxide root canal sealer (Sealapex) on the microtensile bond strengths (muTBS) of dual-curing resin composite (Clearfil DC Core Automix) to the intrapulpal dentin. Forty standardized coronal-half root canal dentin specimens obtained from human premolars were divided into 4 groups: group A, no treatment (control); group B, Sealapex; group C, NaOCl/Sealapex; group D, EDTA/NaOCl/Sealapex. After 7 days of storage in 100% relative humidity, Sealapex was removed. Dentin surfaces were bonded with adhesives, either etch-and-rinse (Single Bond) or self-etching (Clearfil SE Bond), and built up with resin composite. The bonded specimens were trimmed into an hourglass shape with a 1-mm2 cross-sectional area for microtensile testing (n = 20). The muTBS to intrapulpal dentin was analyzed using two-way ANOVA and Dunnett's TC test. Two teeth of each group were prepared for micromorphological analysis of dentin surface. The root canal sealer with or without endodontic irrigation significantly affected the bond strengths of resin composite to intrapulpal dentin compared with the control group (p 0.05). The dentin surface was covered with a mud-like material after sealer application for 7 days. The root canal sealer reduced the muTBS of dual-curing resin composite with etch-and-rinse and self-etching adhesive systems to intrapulpal dentin. Treatment with EDTA followed by NaOCI prior to obturation caused an additional reduction in muTBS of both adhesive systems to intrapulpal dentin.

The effect of Er:YAG laser irradiation on the bond stability of self-etch adhesives at different dentin depths.

Science.gov (United States)

Karadas, Muhammet; Çağlar, İpek

2017-07-01

The aim of this study was to evaluate the effect of Er:YAG laser irradiation on the micro-shear bond strength of self-etch adhesives to the superficial dentin and the deep dentin before and after thermocycling. Superficial dentin and deep dentin surfaces were prepared by flattening of the occlusal surfaces of extracted human third molars. The deep or superficial dentin specimens were randomized into three groups according to the following surface treatments: group I (control group), group II (Er:YAG laser; 1.2 W), and group III (Er:YAG laser; 0.5 W). Clearfil SE Bond or Clearfil S 3 Bond was applied to each group's dentin surfaces. After construction of the composite blocks on the dentin surface, the micro-shear bond testing of each adhesive was performed at 24 h or after 15,000 thermal cycles. The data were analyzed using a univariate analysis of variance and Tukey's test (p  0.05). However, deep-dentin specimens irradiated with laser showed significantly higher bond strengths than did control specimens after thermocycling (p adhesives may be altered by the dentin depth. Regardless of the applied surface treatment, deep dentin showed significant bond degradation.

Influence of irrigation regimens on the adherence of Enterococcus faecalis to root canal dentin.

Science.gov (United States)

Kishen, Anil; Sum, Chee-Peng; Mathew, Shibi; Lim, Chwee-Teck

2008-07-01

Enterococcus faecalis is frequently associated with post-treatment endodontic infections. Because adherence of bacteria to a substrate is the earliest stage in biofilm formation, eliciting the factors that links adherence of this bacterium to dentin would help in understanding its association with treatment-failed root canals. This investigation aimed to study the effects of endodontic irrigants on the adherence of E. faecalis to dentin. The bacteria adherence assay was conducted by using fluorescence microscopy, and the adhesion force was measured by using atomic force microscopy. There were significant increases in adherence and adhesion force after irrigation of dentin with ethylenediaminetetraacetic acid (EDTA), whereas sodium hypochlorite (NaOCl) reduced it. With the use of chlorhexidine (CHX), the force of adhesion increased, but the adherence assay showed a reduction in the number of adhering bacteria. The irrigation regimen of EDTA, NaOCl, and CHX resulted in the least number of adhering E. faecalis cells. This study highlighted that chemicals that alter the physicochemical properties of dentin will influence the nature of adherence, adhesion force, and subsequent biofilm formation of E. faecalis to dentin.

The effect of root canal preparation on the development of dentin cracks.

Science.gov (United States)

Milani, Amin Salem; Froughreyhani, Mohammad; Rahimi, Saeed; Jafarabadi, Mohammad Asghari; Paksefat, Sara

2012-01-01

Root fracture is not an instant phenomenon but a result of gradual development of tiny craze lines in tooth structure. Recent studies have shown that canal instrumentation has the potential to cause dentinal cracks. The purpose of this study was to evaluate and compare the formation of dentinal cracks caused by ProTaper rotary system to hand instrumentation. This in vitro study was carried out using 57 mandible incisor teeth. The teeth were decoronated. The roots were then examined to exclude cracked samples. A standard model for PDL simulation was used. The teeth were randomly divided into two experimental and one control group (n=19). The teeth in the experimental groups were prepared using hand or ProTaper Universal rotary instrumentation. The teeth in the control group were left unprepared. The teeth were then sectioned horizontally 3 and 6 mm from the apex, and the number of various dentinal defects was recorded using a dental operating microscope. The differences between groups were analyzed with Fisher's exact test. The hand group demonstrated significantly more defects than the control group (P=0.001). However, there was no significant difference between the rotary compared to the control and hand groups (P>0.05). There was no significant difference between groups with regards to fracture (P>0.05). Other defects including internal, external and surface cracks were more frequent in the hand than in the control or rotary groups (P=0.02), but the difference was not significant between the rotary and control groups (P>0.05). Canal preparation, whether hand or rotary, produces structural defects in dentin. The ProTaper rotary system when used according to the manufacturer's instructions, tends to produce fewer cracks and can be considered a safe preparation technique.

Assessment of the bacteria reduction in the infected root canal irradiated with diode laser; Avaliacao da reducao bacteriana em conduto radicular infectado e irradiado com laser de diodo. Estudo in vitro

Energy Technology Data Exchange (ETDEWEB)

Radaelli, Claudia Amaral Rabello de Mello

2002-07-01

High success rates are achieved in conventional endodontic treatment of vital pulp teeth. However, in cases of non-vital pulp, a decrease in the rate of success occurs due to difficulties in achieving a complete disinfection of the root canals system. Some bacteria, such as Enterococcus faecalis, are frequently found in cases of endodontic treatment failure due to their high resistance to the conventional endodontic treatment. The aim of this study was to evaluate the efficiency of a high power diode laser irradiation in bacterial reduction of contaminated canals associated with dressing compose by calcium hydroxide paste propylene glycol and camphorated paramonochlorophenol. Eighty-two root canals were infected in vitro with Enterococcus faecalis in a concentration of 1x10{sup 8} CFU/ml. Specimens were high intensity irradiated with a diode laser model Opus 10, at a wavelength of 830 nm. Two different parameters were employed in continuous mode: 3 W and 2,5 W with a 360 {mu}m optical fiber at an angle of approximately 5 degrees respect to the dentine surface during 5 seconds, in 4 applications, with 20 seconds intervals among them. After these proceedings specimens were vortexed in peptone water and dilutions performed. Aliquots of the dilution were plated on m-Enterococcus agar, incubated, and the Colonies Forming Units (CFU) of ali groups was counted. The results showed a significant reduction of bacteria on ali groups after laser irradiation. A high reduction rate was achieved: 98.5% immediately after the laser irradiation; 48 hours after, the reduction was of 96,73% and, finally, a 100% reduction was achieved through the combination of laser irradiation and a long lasting dressing of calcium hydroxide paste, propylene glycol and camphorated paramonochlorophenol. High rates of bacteria reduction were achieved using the parameter of 3 W in continuous mode with the power of 2,9473 KW/cm{sup 2}. The temperature was monitored with a K-pipe thermocouple placed at

In vitro study of temperature changes in root during Er:YAG laser application

International Nuclear Information System (INIS)

Brandao, Redson Vilela

2001-01-01

The temperature increase in root dentine irradiated by Er:YAG laser beam was analyzed, for different dentine thickness and different energy and frequency conditions, aiming the evaluation of Er:YAG laser in endodontic therapy, without causing any damages to close tissues. Twenty four human teeth were separated in four groups with six teeth each, and longitudinally sectioned in thickness of 0.5 mm (first group), 1,0 mm (second group), 1,5 mm (third group) and 2,0 mm (fourth group). Those samples were irradiated with the Er:YAG laser, emitting at the wavelength of 2.94μm, by using a sapphire optic fiber with diameter of 0.375 mm, and forming an angle of 5 deg with the irradiated dentine surface. Three different laser energies were used in this study, 180 mJ, 160 mJ and 140 mJ, with frequencies of 10 Hz and 15 Hz. The temperature data were collected in a digital-analog system and sent to a computer for analysis. It was verified that the time for temperature increases of 5 deg in the external root walls varies according to the laser energy, repetition rate and dentine root thickness. Thus, in this work we could obtain laser parameters to avoid thermal damages in periodontal tissues. (author)

The Effect of Laser Irradiation on Shear Bond Strength of GI to Dentin After CPP-ACP Treatment

Directory of Open Access Journals (Sweden)

Moezizadeh

2016-02-01

Full Text Available Background Dentin sensitivity is one of the most important problems in dentistry. Enamel loss due to root exposure is serious issue and common exposure is one of the reasons for dentin hypersensitivity. There are different methods for solving this problem. One of the most conservative and least expensive methods is use of casein phosphopeptide-amorphous calcium phosphate (CPP-ACP paste. Objectives The aim of this study was to evaluate shear bond strength of GIC to dentin, with or without laser, CPP-ACP paste and polyacrylic acid treatments. Materials and Methods Fifty sound human third molars were bisected in a mesiodistal direction using a diamond disk. Using 400, 600 and 800 grit silicon carbide paper, dentin surfaces were exposed. The teeth were divided into five groups. In groups A, B, D and H, CPP-ACP (GC tooth mousse Itabashi-Ku, Tokyo, Japan was applied for one hour the first day and repeated at the same time of day for a total of five days. In groups B, C, D and E, the specimens were subjected to laser for 10 seconds using Er, Cr: YSGG laser. In groups B, C, H and G, specimens were treated with 10% polyacrylic acid for 20 seconds. A plastic tube containing GI was positioned over the tooth. Samples were loaded in shear bond using a Universal Testing Machine (Zwick/Roell, Germany, at a 0.5 mm/minute crosshead speed. Results Despite the failing of groups A and D, group analysis showed that there were no significant differences between the groups. The predominant type of fracture in all groups was adhesive. Conclusions Application of CPP-ACP, without preconditioning with polyacrylic acid, can decrease shear bond strength. Laser irradiation has no effect on shear bond strength of GIC to dentin in this condition.

Effect of QMix, peracetic acid and ethylenediaminetetraacetic acid on calcium loss and microhardness of root dentine

Science.gov (United States)

Taneja, Sonali; Kumari, Manju; Anand, Surbhi

2014-01-01

Objectives: The objective of this in vitro study was to assess the effect of different chelating agents on the calcium loss and its subsequent effect on the microhardness of the root dentin. Materials and Methods: Ten single rooted lower premolars were selected. The teeth were decoronated and thick transverse sections of 2 mm were obtained from the coronal third of the root. Each section was then divided into four quarters, each part constituting a sample specimen from the same tooth for each group. The treatment groups were: Group 1 (Control): 5% Sodium hypochlorite (NaOCl) for 5 min + distilled water for 5 min; Group 2: 5% NaOCl for 5 min + 17% ethylenediaminetetraacetic acid (EDTA) for 5 min; Group 3: 5% NaOCl for 5 min + 2.25% Peracetic acid (PAA) for 5 min and Group 4: 5% NaOCl for 5 min + QMix for 5 min respectively. The calcium loss of the samples was evaluated using the Atomic Absorption Spectrophotometer followed by determination of their microhardness using Vickers Hardness Tester. Data was analyzed using one-way ANOVA, Post hoc Tukey test and Pearson correlation. Results: The maximum calcium loss and minimum microhardness was observed in Group 3 followed by Group 2, Group 4 and Group 1. There was a statistically significant difference between all the groups except between Groups 2 and 4. Conclusions: Irrigation with NaOCl + 2.25% PAA caused the maximum calcium loss from root dentin and reduced microhardness. A negative correlation existed between the calcium loss and reduction in the microhardness of root dentin. PMID:24778513

Comparison of effects of ProTaper, HeroShaper, and Gates Glidden Burs on cervical dentin thickness and root canal volume by using multislice computed tomography.

Science.gov (United States)

Mahran, Abeer H; AboEl-Fotouh, Mona M

2008-10-01

The purpose of this study was to compare the effects of 3 different instruments used to prepare curved root canals on the remaining cervical dentin thickness and total amount of dentin removed from root canals during instrumentation by using multislice computed tomography. Mesiobuccal canals of 45 mandibular first molars with curvature between 30-40 degrees were divided into 3 equal groups: ProTaper, Hero Shaper, and Gates Glidden Bur with Flex-R hand file. Cervical dentin thickness and canal volume were measured before and after instrumentation by using multislice computed tomography and image analysis software. The results indicated that ProTaper removed significantly less cervical dentin from distal wall of the root (dangerous zone) than HeroShaper and Gates Glidden Bur (P ProTaper system (P < .05).

Histopathologic study on irradiated human developing teeth

Energy Technology Data Exchange (ETDEWEB)

Takeda, Yasunori (Iwate Medical Coll., Morioka (Japan). School of Dentistry)

1982-12-01

The patient was a 7-year-old boy who had been suffering from Ewing's sarcoma originating in the mandible. Irradiation with 8000 rad of Linac was performed on the mandible prior to mandibulectomy. The results of the histopathologic examination of the teeth including resected material were as follows: 1. Although the tumor tissue was not found in the resected material, complete resoption of the medullar trabecular bone with fibrosis was noted in the area between the first molar region and the mandibular ramus. 2. The first and the second premolar teeth were in the early stage of root formation, and conglomerates of dysplastic dentin were formed in the proliferative zones. This dysplastic dentin was surrounded by loose fibrous connective tissues. 3. The dysplastic dentin showed low mineralization, embedded irregular arranged-fibrous tissue matrix and scattered various-sized lacunae containing a few tiny and pyknotic cells. 4. Irregularly arranged odontoblasts with a pyknotic appearance were found along the tubular dentin, but diffuse fibrosis occurred in the pulpal tissues. 5. The first molar tooth had completed its root formation. Various amounts of osteodentin were formed at the secondary dentin layer. Inner-resorption of dentin and fibrosis of the pulpal tissue were also found. These changes concerning the first molar tooth were also due to the effects of irradiation. 6. The second molar tooth was resorbed by tumor infiltration, and dysplastic dentin was on the resorbed surface of the dentin.

Does laser diode irradiation improve the degree of conversion of simplified dentin bonding systems?

Directory of Open Access Journals (Sweden)

Leticia Ferreira de Freitas BRIANEZZI

Full Text Available Abstract Simplified dentin-bonding systems are clinically employed for most adhesive procedures, and they are prone to hydrolytic degradation. Objective This study aimed to investigate the effect of laser diode irradiation on the degree of conversion (DC, water sorption (WS, and water solubility (WSB of these bonding systems in an attempt to improve their physico-mechanical resistance. Material and Methods Two bonding agents were tested: a two-step total-etch system [Adper™ Single Bond 2, 3M ESPE (SB] and a universal system [Adper™ Single Bond Universal, 3M ESPE (SU]. Square-shaped specimens were prepared and assigned into 4 groups (n=5: SB and SU (control groups – no laser irradiation and SB-L and SU-L [SB and SU laser (L – irradiated groups]. DC was assessed using Fourier transform infrared spectroscopy with attenuated total reflectance. Additional uncured resin samples (≈3.0 µL, n=5 of each adhesive were also scanned for final DC calculation. For WS/WSB tests, similar specimens (n=10 were prepared and measured by monitoring the mass changes after dehydration/water storage cycles. For both tests, adhesive fluids were dropped into standardized Teflon molds (6.0×6.0×1.0 mm, irradiated with a 970-nm laser diode, and then polymerized with an LED-curing unit (1 W/cm2. Results Laser irradiation immediately before photopolymerization increased the DC (% of the tested adhesives: SB-L>SB>SU-L>SU. For WS/WSB (μg/mm3, only the dentin bonding system (DBS was a significant factor (pSU. Conclusion Irradiation with a laser diode improved the degree of conversion of all tested simplified dentin bonding systems, with no impact on water sorption and solubility.

Characterization of caries progression on dentin after irradiation with Nd:YAG laser by FTIR spectroscopy and fluorescence imaging

Science.gov (United States)

Ana, P. A.; Brito, A. M. M.; Zezell, D. M.; Lins, E. C. C. C.

2015-06-01

Considering the use of high intensity lasers for preventing dental caries, this blind in vitro study evaluated the compositional and fluorescence effects promoted by Nd:YAG laser (λ=1064 nm) when applied for prevention of progression of dentin caries, in association or not with topical application of acidulated phosphate fluoride (APF). Sixty bovine root dentin slabs were prepared and demineralized by 32h in order to create early caries lesions. After, the slabs were distributed into six experimental groups: G1- untreated and not submitted to a pH-cycling model; G2- untreated and submitted to a pH-cycling model; G3- acidulated phosphate fluoride application (APF); G4- Nd:YAG irradiation (84.9 J/cm2, 60 mJ/pulse); G5- treated with Nd:YAG+APF; G6- treated with APF+Nd:YAG. After treatments, the samples of groups G2 to G6 were submitted to a 4-day pH-cycling model in order to simulate the progression of early caries lesions. All samples were characterized by the micro-attenuated total reflection technique of Fourier transformed infrared spectroscopy (μATR-FTIR), using a diamond crystal, and by a fluorescence imaging system (FIS), in which it was used an illuminating system at λ= 405±30 nm. Demineralization promoted reduction in carbonate and phosphate contents, exposing the organic matter; as well, it was observed a significant reduction of fluorescence intensity. Nd:YAG laser promoted additional chemical changes, and increased the fluorescence intensity even with the development of caries lesions. It was concluded that the compositional changes promoted by Nd:YAG, when associated to APF, are responsible for the reduction of demineralization progression observed on root dentin.

Effect of medium and post-irradiation storage on rooting of irradiated onions

International Nuclear Information System (INIS)

Singh, Rita

2000-01-01

Rooting test for detection of irradiation in onion bulbs was studied. Onions were exposed to different dose levels of 30, 60, 90, 120 and 150 Gy. The effects of irradiation dose, cultivar difference, rooting medium and post-irradiation storage on the rooting were investigated. The number and the length of the roots formed in onions were found to decrease on irradiation. The effect was more at higher doses. The effect of irradiation on rooting was also evident after 120 days of storage. (author)

Evaluation of the dentin changes in teeth subjected to endodontic treatment and photodynamic therapy

Directory of Open Access Journals (Sweden)

Mariane Floriano Lopes Santos LACERDA

Full Text Available Abstract Introduction Antimicrobial photodynamic therapy (PDT is an efficient adjuvant technique to promote disinfection of the root canal system. Therefore, it is important to investigate changes to dentin morphology and permeability induced by the use of diode laser on the root dentin. Objective The purpose of this study was to investigate morphological changes and the percentage of apical leakage after the use of laser. Material and method Forty single-rooted teeth were instrumented using rotary system and irrigated. Teeth were randomly divided in two groups: G1 - not exposed to PDT (control, and G2 - pretreated with toluidine blue photosensitizer and irradiated with AsGaAl laser diode. Ten teeth in each group were evaluated by SEM for morphological changes. The other ten teeth were filled and stained with Rhodamine B to evaluate the apical leakage. Result The results showed significant difference between G1 and G2 (p 0.001. The apical leakage was significantly higher in G2 than in G1 (p <0.001 - Student's t-test. Conclusion It was concluded that the use of low-level laser reduced the smear layer and opened the dentinal tubules. Use of laser increased the permeability of the apical dentin.

Bond strength of an adhesive system irradiated with Nd:YAG laser in dentin treated with Er:YAG laser

International Nuclear Information System (INIS)

Malta, D A M P; De Andrade, M F; Costa, M M; Lizarelli, R F Z; Pelino, J E P

2008-01-01

The purpose of this in vitro study was to verify through micro tensile bond test the bond strength of an adhesive system irradiated with Nd:YAG laser in dentine previously treated with Er:YAG laser. Twenty caries free extracted human third molars were used. The teeth were divided in four experimental groups (n = 5): (G1) control group; (G2) irradiation of the adhesive system with the Nd:YAG laser; (G3) dentin treatment with Er:YAG laser; (G4) dentin treatment with Er:YAG laser followed by the irradiation of the adhesive system with Nd:YAG laser. The Er:YAG laser fluency parameter for the dentin treatment was of 60 J/cm 2 . The adhesive system was irradiated with the Nd:YAG laser with fluency of 100 J/cm 2 . Dental restorations were performed with Adper Single Bond 2/Z250. One tooth from each group was prepared for the evaluation of the adhesive interface under SEM and bond failure tests were also performed and evaluated. The statistical analysis showed statistical significant difference between the groups G1 and G3, G1 and G4, G2 and G3, and G2 and G4; and similarity between the groups G1 and G2, and G3 and G4. The adhesive failures were predominant in all the experimental groups. The SEM analysis showed an adhesive interface with features confirming the results of the mechanical tests. The Nd:YAG laser on the adhesive system did not influence the bond strength in dentin treated or not with the Er:YAG laser

Effect of gamma radiation and endodontic treatment on mechanical properties of human and bovine root dentin

Energy Technology Data Exchange (ETDEWEB)

Novais, Veridiana Resende; Soares, Priscilla Barbosa Ferreira; Guimaraes, Carlla Martins; Schliebe, Lais Rani Sales Oliveira; Braga, Stella Sueli Lourenco; Soares, Carlos Jose, E-mail: carlosjsoares@ufu.br [Universidade Federal de Uberlandia (UFU), MG (Brazil)

2016-11-15

This study evaluated the effect of gamma radiation and endodontic treatment on the microhardness and flexural strength of human and bovine root dentin. Forty single rooted human teeth and forty bovine incisor teeth were collected, cleaned and stored in distilled water at 4 °C. The human and bovine teeth were divided into 4 groups (n=10) resulting from the combination of two study factors: first, regarding the endodontic treatment in 2 levels: with or without endodontic treatment; and second, radiotherapy in two levels: with or without radiotherapy by 60 Gy of Co-60 gamma radiation fractioned into 2 Gy daily doses five days per week. Each tooth was longitudinally sectioned in two parts; one-half was used for the three-point bending test and the other for the Knoop hardness test (KHN). Data were analyzed by 3-way ANOVA and Tukey HSD test (α=0.05). No significant difference was found for flexural strength values. The human dentin had significantly higher KHN than the bovine. The endodontic treatment and radiotherapy resulted in significantly lower KHN irrespective of tooth origin. The results indicated that the radiotherapy had deleterious effects on the microhardness of human and bovine dentin and this effect is increased by the interaction with endodontic therapy. The endodontic treatment adds additional negative effect on the mechanical properties of radiated tooth dentin; the restorative protocols should be designed taking into account this effect. (author)

Effect of gamma radiation and endodontic treatment on mechanical properties of human and bovine root dentin

International Nuclear Information System (INIS)

Novais, Veridiana Resende; Soares, Priscilla Barbosa Ferreira; Guimaraes, Carlla Martins; Schliebe, Lais Rani Sales Oliveira; Braga, Stella Sueli Lourenco; Soares, Carlos Jose

2016-01-01

This study evaluated the effect of gamma radiation and endodontic treatment on the microhardness and flexural strength of human and bovine root dentin. Forty single rooted human teeth and forty bovine incisor teeth were collected, cleaned and stored in distilled water at 4 °C. The human and bovine teeth were divided into 4 groups (n=10) resulting from the combination of two study factors: first, regarding the endodontic treatment in 2 levels: with or without endodontic treatment; and second, radiotherapy in two levels: with or without radiotherapy by 60 Gy of Co-60 gamma radiation fractioned into 2 Gy daily doses five days per week. Each tooth was longitudinally sectioned in two parts; one-half was used for the three-point bending test and the other for the Knoop hardness test (KHN). Data were analyzed by 3-way ANOVA and Tukey HSD test (α=0.05). No significant difference was found for flexural strength values. The human dentin had significantly higher KHN than the bovine. The endodontic treatment and radiotherapy resulted in significantly lower KHN irrespective of tooth origin. The results indicated that the radiotherapy had deleterious effects on the microhardness of human and bovine dentin and this effect is increased by the interaction with endodontic therapy. The endodontic treatment adds additional negative effect on the mechanical properties of radiated tooth dentin; the restorative protocols should be designed taking into account this effect. (author)

Impact of combined CO2 laser irradiation and fluoride on enamel and dentin biofilm-induced mineral loss.

Science.gov (United States)

Esteves-Oliveira, Marcella; El-Sayed, Karim Fawzy; Dörfer, Christof; Schwendicke, Falk

2017-05-01

The caries-protective effects of CO 2 laser irradiation on dental enamel have been demonstrated using chemical demineralization models. We compared the effect of CO 2 laser irradiation, sodium fluoride, or both on biofilm-induced mineral loss (∆Z) and Streptococcus mutans adhesion to enamel and dentin in vitro. Ground, polished bovine enamel, and dentin samples were allocated to four groups (n = 12/group): no treatment (C); single 22,600-ppm fluoride (F) varnish (5 % NaF) application; single CO 2 laser treatment (L) with short pulses (5 μs/λ = 10.6 μm); and laser and subsequent fluoride treatment (LF). Samples were sterilized and submitted to an automated mono-species S. mutans biofilm model. Brain heart infusion plus 5 % sucrose medium was provided eight times daily, followed by rinses with artificial saliva. After 10 days, bacterial numbers in biofilms were enumerated as colony-forming units/ml (CFU/ml) (n = 7/group). ∆Z was assessed using transversal microradiography (n = 12/group). Univariate ANOVA with post hoc Tukey honestly-significant-difference test was used for statistical analysis. Bacterial numbers were significantly higher on dentin than enamel (p  0.05). In dentin, only LF (163/227) significantly reduced ∆Z (p fluoride application was required to protect dentin.

Tensile Bond Strengths of Two Adhesives on Irradiated and Nonirradiated Human Dentin

Directory of Open Access Journals (Sweden)

Cécile Bernard

2015-01-01

Full Text Available The aim of this study was to assess the effect of radiotherapy on bond efficiency of two different adhesive systems using tensile bond strength test. Twenty extracted teeth after radiotherapy and twenty nonirradiated extracted teeth were used. The irradiation was applied in vivo to a minimal dose of 50 Gy. The specimens of each group were randomly assigned to two subgroups to test two different adhesive systems. A three-step/etch-and-rinse adhesive system (Optibond FL and a two-steps/self-etch adhesive system (Optibond XTR were used. Composite buildups were performed with a nanohybrid composite (Herculite XTR. All specimens were submitted to thermocycling ageing (10000 cycles. The specimens were sectioned in 1 mm2 sticks. Microtensile bond strength tests were measured. Nonparametric statistical analyses were performed due to nonnormality of data. Optibond XTR on irradiated and nonirradiated teeth did not show any significant differences. However, Optibond FL bond strength was more effective on nonirradiated teeth than on irradiated teeth. Within the limitations of an in vitro study, it can be concluded that radiotherapy had a significant detrimental effect on bond strength to human dentin. However, it seems that adhesive choice could be adapted to the substrata. According to the present study, the two-steps/self-etch (Optibond XTR adhesive system tested could be more effective on irradiated dentin compared to three-steps/etch-and-rinse adhesive system (Optibond FL.

In vitro antimicrobial activity of various medication preparations on E. faecalis in root canal dentin.

Science.gov (United States)

Lynne, Richard E; Liewehr, Frederick R; West, Lesley A; Patton, William R; Buxton, Thomas B; McPherson, James C

2003-03-01

The purpose of this study was to evaluate the antimicrobial activity of several medication preparations in root canal dentin infected with Enterococcus faecalis. Roots of extracted bovine incisors were prepared to standardized cylindrical test specimens, 5 mm in height. The smear layer was removed and the samples were autoclaved and then incubated at 37 degrees C/5% CO2 for 24 h in brain-heart infusion (BHI) broth containing 7.0 x 10(4) colony forming units per ml of E. faecalis. The samples were washed in phosphate buffered saline and mounted to individual culture wells with sticky wax. Test medications were applied to fill the canal lumina; medication groups were: (a) sterile H2O (positive control); (b) a 10% mixture of 1.0 g Ca(OH)2 USP in 10 ml sterile H2O; (c) 10% Ca(OH)2 in 0.12% chlorhexidine gluconate (Peridex); (d) Peridex; and (e) uninoculated BHI (negative control). The samples were incubated at 37 degrees C/5% CO2 for 24 h. Dentin samples for quantitative microbiology were then obtained with consecutive sterile burs (ISO 029, 035, 042). All three experimental groups demonstrated significantly greater antimicrobial activity than the positive control (p effective than Peridex or 10% Ca(OH)2 in Peridex for the elimination of E. faecalis from dentin tubules.

Comparison of the remaining dentin thickness in the root after hand and four rotary instrumentation techniques: an in vitro study.

Science.gov (United States)

Rao, M S Rama; Shameem, Abdul; Nair, Rashmi; Ghanta, Sureshbabu; Thankachan, Rekha P; Issac, Johnson K

2013-07-01

The aim of the present study was to compare the remaining dental thickness (RDT) in the mesiobuccal root of mandibular first molars at 3 and 7 mm from the anatomic apex after instrumentation with ProTaper, light speed LSX, K3 and M2 and to compare with that of K-files. In this study, 60 extracted, untreated human mandibular first molars with fully formed apices, with curvature less than 35° and no root resorption were used. Prepared specimens were cut horizontally at 3 and 7 mm short of anatomic apex. The least dentin thickness from canal to external root surface was observed under 3× magnification and recorded using Clemax measuring tool and the sections were reassembled. Group I-instrumentation with ProTaper, group II-instrumentation with K3, group III-instrumentation with Light Speed LSX, group IV-instrumentation with M2 and group V- instrumentation with K-files and RDT was measured. Results showed that group V removed lesser amount of dentin compared to all other groups while all the three instrumentation techniques removed almost equal amount of dentin apically. Cleaning and shaping of the root canal space involves the elimination of pathogenic contents as well as attaining a uniform specific shape. However, the RDT following the use of various intraradicular procedures is an important factor to be considered as an iatrogenic cause that may result in root fracture. To avoid this, newer rotary instruments are being introduced.

Evaluation in vitro of effects of Er:YAG and Nd:YAG lasers irradiation on root canal wall, by stereoscopy, scanning electron micrography and thermographic camera; Avaliacao in vitro dos efeitos da irradiacao laser de Er:YAG e Nd:YAG na parede dentinaria do canal radicular, sob observacao do estereoscopio, da micrografia eletronica e da camera termografica

Energy Technology Data Exchange (ETDEWEB)

Goya, Claudia

2001-07-01

This study was carried out to evaluate in vitro the effects of Nd:YAG laser and Er:YAG laser irradiation in the root canal wall by SEM, evaluating the apical leakage and the temperature changes during the laser irradiation. Seventy four extracted human teeth were used, they were instrumented and divided into seven groups of 10 teeth each. The teeth were evaluated through stereoscopy, by SEM, and with the thermographic camera. The Nd:YAG laser irradiation parameters were 100 mJ/p, 15 Hz, and Er:YAG laser were 160 mJ/p and 10 Hz, the irradiation was 4 times at 2 mm/sec speed, with 20 sec interval. The apical leakage was not observed in the teeth irradiated by Nd:YAG laser alone or in association with Er:YAG laser. However in the teeth irradiated only by the Er:YAG laser we observed a little leakage. By SEM observation the Nd:YAG laser irradiation showed melting and recrystallization in the dentin surface closing dentinal tubules, and in the samples irradiated by Er:Y AG laser a clean surface, opened dentinal tubules, and the combination by two lasers, showed melting covering some dentinal tubules The thermographic study found the temperature increase was not more than 6 deg C. This study showed the safety parameters applications of Er:YAG laser in association with Nd:YAG laser in root canal treatment, in order to not cause thermal damages to the periodontal tissues. (author)

Dentinal temperature transients caused by exposure to CO2 laser irradiation and possible pulpal damage.

Science.gov (United States)

Jeffrey, I W; Lawrenson, B; Saunders, E M; Longbottom, C

1990-02-01

An investigation is described that attempts to establish, in vitro, the characteristics of heat transference following laser irradiation of bovine dentinal tissue and the relationship with the periodicity of radiation. The results of this study appear to indicate that at depths of overlying dentine of up to 3 mm, laser-induced thermal injury to the pulp is a definite possibility. Fail-safe facilities to prevent build up of heat must be incorporated into the design of dental lasers to allow their beneficial effects to be utilized without the risk of iatrogenic damage.

The effects of different nickel-titanium instruments on dentinal microcrack formations during root canal preparation.

Science.gov (United States)

Ustun, Yakup; Aslan, Tugrul; Sagsen, Burak; Kesim, Bertan

2015-01-01

The aim of the present study was to investigate the incidence of dentinal microcracks caused by different preparation techniques. 120 extracted human mandibular incisor teeth were divided into five experimental groups and one control group (n = 20): Group 1: Hand preparation with balanced force technique up to #25 K-file. Group 2: Preparation with only ProTaper F2 instrument in a reciprocating movement. Group 3: Preparation with Reciproc R25 instrument in a reciprocating movement. Group 4: Preparation with ProTaper instruments up to F2 instrument. Group 5: Preparation with ProTaper Next instruments up to X2 instrument. No procedure was applied to control group. The roots were sectioned horizontally at 3, 6 and 9 mm from the apex and examined. Absence or presence of dentinal microcracks was noted. The Chi-square test was performed to compare the appearance of cracked roots between all groups. There were no significant differences among the groups (P > 0.05). In conclusion, except the hand file and control group, all experimental groups showed microcrack formations.

Morphological Alterations of the Surfaces of Enamel and Dentin of Deciduous Teeth Irradiated with Nd:YAG, C0(2)and Diode Lasers

OpenAIRE

Souza, Mónica Rodrigues de; Watanabe, Ii-Sei; Azevedo, Luciane H; Tanji, Edgar Y

2009-01-01

In this work, we studied the effects of C0(2), Nd:YAG and diode lasers on the enamel and dentin of deciduous human teeth. After the irradiations, the samples were duly prepared and set up on metallic bases, covered with gold and examined in the scanning electron microscope. The results showed that the irradiation with the C0(2) mode locked laser with 1.0 W power caused melting and irregularities with small cavities on the surface of the enamel. The irradiated area on the dentin surface appear...

Comparison of the effects of TripleGates and Gates-Glidden burs on cervical dentin thickness and root canal area by using cone beam computed tomography

Directory of Open Access Journals (Sweden)

Kássio SOUSA

2015-04-01

Full Text Available The search for new instruments to promote an appropriate cervical preparation has led to the development of new rotary instruments such as TripleGates. However, to the best of the authors' knowledge, there is no study evaluating TripleGates effect on the “risk zone” of mandibular molars. Objectives : The aim of this study was to evaluate the effects of a crown-down sequence of Gates-Glidden and TripleGates burs on the remaining cervical dentin thickness and the total amount of dentin removed from the root canals during the instrumentation by using cone beam computed tomography. The number of separated instruments was also evaluated. Material and Methods : Mesial roots of 40 mandibular first molars were divided into 2 equal groups: crown-down sequence of Gates-Glidden (#3, #2, #1 and TripleGates burs. Cervical dentin thickness and canal area were measured before and after instrumentation by using cone beam computed tomography and image analysis software. Student’s t-test was used to determine significant differences at p0.05 were observed between the instruments, regarding the root canal area and dentin wall thickness. Conclusion : Both tested instruments used for cervical preparation were safe to be used in the mesial root canal of mandibular molars.

Bacterial leakage in root canals filled with AH Plus and dentine bonding agents.

Science.gov (United States)

Navarro-Escobar, Esther; Baca, Pilar; Ruiz-Linares, Matilde; Arias-Moliz, Maria Teresa; Perez-Heredia, Mercedes; Ferrer-Luque, Carmen Maria

2014-11-01

The aim of this study was to compare the efficacy of different dentine adhesives in delaying the coronal bacterial leakage of Enterococcus faecalis in filled root canals. Materials and methods. Ninety-five lower incisors of patients >65 years of age were instrumented using the ProTaper system and were irrigated with 1 mL of 2.5% sodium hypochlorite (NaOCl) alternated with 1 mL 17% EDTA between each file change. Final irrigation was performed with 5 mL of 17% EDTA and then flushed with 5 mL of distilled water. The teeth were randomly divided into five experimental groups (n = 15/group) and one of the following dentine adhesives was applied: (1) AdheSE; (2) Excite DSC; (3) Clearfil Protect Bond; (4) One Coat 7.0; or (5) Control group without adhesive. After filling the root canals, the samples were mounted on a double chamber device to evaluate the bacterial filtration of E. faecalis during a period of 240 days. The results underwent non-parametric Kaplan-Meier survival analysis and comparisons among groups were done using the Log-Rank test. At 240 days, E. faecalis was detected in samples of all groups in the lower chamber. The highest survival value was obtained by One Coat 7.0, giving statistically significant differences from the other groups, whereas Clearfil Protect Bond, AdheSE and Excite DSC showed similar behaviours, likewise similar to the Control group. One Coat 7.0 adhesive system provides the longest survival value to delay E. faecalis coronal leakage in filled root canals.

Effects of the copper vapour laser radiation in the root canal wall dentine: in vitro experiment using scanning electron microscopy and stereoscopy; Efeitos da radiacao laser de vapor de cobre na parede de dentina de canais radiculares: estudo in vitro por meio de microscopia eletronica de varredura e microscopio estereoscopico

Energy Technology Data Exchange (ETDEWEB)

Silveira, Maria Claudia Garcia da

2001-07-01

Ten human uniradicular teeth had their crown removed along the cement-enamel junction and right away a proper chemical-surgical preparation of the radicular canals was done; the roots were longitudinally sectioned in order to allow the irradiation of the surfaces of the root canals wall dentine. The hemi-roots were separated in two groups: group I (control), with four hemi-roots, not irradiated; and group II, with 16 hemi-roots, subdivided in four sub-groups submitted to the following exposition time: 0,02 s; 0,05 s; 0,1 s and 0,5 s. A copper vapour laser was used with a 510,6 nm wavelength, total average power of 11 W in green and yellow emissions; average power of 6,5 W in green emission; pulse repetition rate of 16.000 Hz and pulse duration of 30 ns. The pulse energy (green line) is 0,4 mJ and the peak power 13,5 W. The laser cavity is unstable type (R{sub 1}=3.900 mm and R{sub 2}-250 mm). The focusing have focal length lens f{sub 1}=250 mm and f{sub 2}=150 mm. The beam quality is of the M{sup 2}=5. The results obtained by scanning electron microscopy analysis showed the appearance of a cavity in the region of the laser beam incidence in the edges of this cavity, dentin was melt and resolidified presenting also cracks due to heat diffusion. Based on these results, we concluded that the size of the cavity formed in the dentin is directly proportional to the rate of exposure and, the more laser emission in the same area, more damage in the root canals wall dentin occurs. More studies need to be done with different exposition's time in order to obtain a safety protocol that does not cause injury in dental and support tissue. (author)

Comparison of removed dentin thickness with hand and rotary instruments

Science.gov (United States)

Shahriari, Shahriar; Abedi, Hasan; Hashemi, Mahdi; Jalalzadeh, Seyed Mohsen

2009-01-01

INTRODUCTION: The aim of this study was to evaluate the amount of dentine removed after canal preparation using stainless steel (SS) hand instruments or rotary ProFile instruments. MATERIALS AND METHODS: Thirty-six extracted human teeth with root canal curvatures less than 30º were embedded in clear polyester resin. The roots were cut horizontally at apical 2, 4 and 7 mm. Dentin thickness was measured at each section and the sections were accurately reassembled using a muffle. Root canals were randomly prepared by SS hand instruments or rotary ProFile instruments. Root sections were again separated, and the remaining dentin thickness was measured. Mann-Whitney U and t tests were performed for analytic comparison of the results. RESULTS: The thickness of removed dentin was significantly different between the two used methods (Pinstrumentation group (Protary instrumentation prepares root canals with a greater conservation of tooth structure. PMID:23940489

Push-out bond strength of fiber posts to root dentin using glass ionomer and resin modified glass ionomer cements

Directory of Open Access Journals (Sweden)

Jefferson Ricardo PEREIRA

2014-10-01

Full Text Available OBJECTIVE: The purpose of this study was to assess the push-out bond strength of glass fiber posts to root dentin after cementation with glass ionomer (GICs and resinmodified glass ionomer cements (RMGICs. MATERIAL AND METHODS: Fifty human maxillary canines were transversally sectioned at 15 mm from the apex. Canals were prepared with a step back technique until the application of a #55 K-file and filled. Post spaces were prepared and specimens were divided into five groups according to the cement used for post cementation: Luting & Lining Cement; Fuji II LC Improved; RelyX Luting; Ketac Cem; and Ionoseal. After cementation of the glass fiber posts, all roots were stored at 100% humidity until testing. For push-out test, 1-mm thick slices were produced. The push-out test was performed in a universal testing machine at a crosshead speed of 0.5 mm/minute and the values (MPa were analyzed by Kolmogorov-Smirnov and Levene's tests and by two-way ANOVA and Tukey's post hoc test at a significance level of 5%. RESULTS: Fiber posts cemented using Luting & Lining Cement, Fuji II LC Improved, and Ketac Cem presented the highest bond strength to root dentin, followed by RelyX Luting. Ionoseal presented the lowest bond strength values (P>0.05. The post level did not influence the bond strength of fiber posts to root dentin (P=0.148. The major cause of failure was cohesive at the cement for all GICs and RMGICs. CONCLUSIONS: Except for Ionoseal, all cements provided satisfactory bond strength values.

Incidence of dentinal defects after preparation of severely curved root canals using the Reciproc single-file system with and without prior creation of a glide path.

Science.gov (United States)

Saber, S E D M; Schäfer, E

2016-11-01

To investigate the incidence of dentinal defects after preparation of severely curved root canals using the Reciproc single-file system with and without prior creation of a glide path. Mesial roots from extracted mandibular first molars were collected and scanned with CBCT to assess the morphology of the root canal systems. Three groups of 20 anatomically comparable specimens were generated. The control group was left unprepared, whilst the experimental groups were prepared with Reciproc R25 with and without a glide path (groups RG and R, respectively). Roots were then sectioned perpendicular to the long axis at 2, 4, 6, 8 and 10 mm from the apex, and coloured photographs of the sections at 40× were obtained. Two blinded examiners registered the presence of dentinal defects twice at 2-week interval. Data were statistically analysed using the Fisher exact and Cochran's Q tests. No defects were observed in the control group. The overall incidence of dentinal defects was 26% in group R and 24% in group RG, with no significant differences between them (P > 0.05). Dentinal defects occurred significantly more often in the middle and coronal thirds compared to the apical third of the canals (P files. © 2015 International Endodontic Journal. Published by John Wiley & Sons Ltd.

Influence of the incidence angle on the morphology of enamel and dentin under Er:YAG laser irradiation

International Nuclear Information System (INIS)

Junqueira Junior, Duilio Naves

2002-01-01

The purpose of this study is to make an in vitro evaluation, using scanning electron microscopy, of the influence of the laser beam irradiation angle on the enamel and dentin morphology. These tissues were both irradiated by Er:YAG Laser, with the same energy parameter. Twenty-four incisive bovine teeth were used, separated in eight groups, four of enamel, and four of dentin, with three specimens in each group. Each specimen was submitted to three laser applications, varying the incidence angle, between the laser and the tooth surface, at 90, 50 and 20 degrees. The applied frequency was 2 Hz, with 20 pulses in each application. The KaVo Key Laser 3 was employed, wavelength at 2940 nm, adjustable energy from 40 to 600 mJ and repetition rate from 1 to 25 Hz. The groups were distributed according to the energy parameter as follows - enamel: 250 mJ; 300 mJ; 350 mJ and 400 mJ; dentin: 200 mJ; 250 mJ; 300 mJ and 350 mJ. The results evidenced the Laser incidence angle importance; it is an essential parameter in the protocol of utilization and it should not be disregarded. The observations of this study allow to conclude that the Laser incidence angle has direct influence on the morphological aspect of the alterations produced in enamel and dentin. (author)

Apical microinfiltration evaluation of radicular channels irradiated with Er:YAG laser in vitro

International Nuclear Information System (INIS)

Sebrao, Catia Cilene Nass

2003-01-01

It was evaluated, in vitro, the adaptation of the filling material (Sealer 2S R ) to the root channels dentine walls treated using the endodontic technique and prepared with the Er:YAG laser, by the technique of infiltration of methylene blue dye. Using scanning electronic microscopy, the morphologic alteration of the root channel dentine was observed for one sample per studied group. Also, an evaluation of the temperature increase in the external surface of the root during the irradiations was performed for two samples per group. For each group of samples, with eleven roots each, two sub-groups had been considered: the dry, irradiated after completely dry with absorbent cones of paper, and the humid, where a cone of absorbent paper was applied for two seconds in the root canal, leaving them lightly humidified. Considering the used energies for the irradiations, the groups are: G1, control (without irradiation), G2-dry (100 mJ-10 Hz), G2-humid (100 mJ-10 Hz), G3-dry (140 mJ-6 Hz), G3-humid (140 mJ-6 Hz), G4-dry (180 mJ-6 Hz), and G4-humid (180 mJ-6 Hz). The results had shown that apical microinfiltration did not exhibit significant difference among groups. The highest increase in temperature was observed for the dry groups, with the maximum variation of temperature of 6.5 deg C. Under the scanning electronic microscopy analysis, the humid groups had presented cleaner surfaces than the dry groups. The G4-humid group presented extensive regions of fusion and resolidification of the dentine. (author)

Pull-out bond strength of a self-adhesive resin cement to NaOCl-treated root dentin: effect of antioxidizing agents

Directory of Open Access Journals (Sweden)

Maryam Khoroushi

2014-05-01

Full Text Available Objectives This study evaluated the effect of three antioxidizing agents on pull-out bond strengths of dentin treated with sodium hypochlorite. Materials and Methods Root canals of 75 single-rooted human teeth were prepared. Fifteen teeth were irrigated with normal saline for a negative control group, and the remaining 60 teeth (groups 2 - 5 with 2.5% NaOCl. The teeth in group 2 served as a positive control. Prior to post cementation, the root canals in groups 3 - 5 were irrigated with three antioxidizing agents including 10% rosmarinic acid (RA, Baridge essence, 10% hesperidin (HPN, Sigma, and 10% sodium ascorbate hydrogel (SA, AppliChem. Seventy-five spreaders (#55, taper .02, Produits Dentaires S.A were coated with silica and silanized with the Rocatec system and ceramic bond. All the prepared spreaders were cemented with a self-adhesive resin cement (Bifix SE, Voco Gmbh in the prepared canals. After storage in distilled water (24 h/37℃, the spreaders were pulled out in a universal testing machine at a crosshead speed of 1.0 mm/min. Pull-out strength values were analyzed by one-way ANOVA and Tukey's HSD test (α = 0.05. Results There were significant differences between study groups (p = 0.016. The highest pull-out strength was related to the SA group. The lowest strength was obtained in the positive control group. Conclusions Irrigation with NaOCl during canal preparation decreased bond strength of resin cement to root dentin. Amongst the antioxidants tested, SA had superior results in reversing the diminishing effect of NaOCl irrigation on the bond strength to root dentin.

In Vitro Study of Dentin Hypersensitivity Treated by 980-nm Diode Laser.

Science.gov (United States)

Liu, Ying; Gao, Jie; Gao, Yan; Xu, Shuaimei; Zhan, Xueling; Wu, Buling

2013-01-01

To investigate the ultrastructural changes of dentin irradiated with 980-nm diode laser under different parameters and to observe the morphological alterations of odontoblasts and pulp tissue to determine the safety parameters of 980-nm diode laser in the treatment of dentin hypersensitivity (DH). Twenty extracted human third molars were selected to prepare dentin discs. Each dentin disc was divided into four areas and was irradiated by 980-nm diode laser under different parameters: Group A: control group, 0 J/cm(2); Group B: 2 W/CW (continuous mode), 166 J/cm(2); Group C: 3W/CW, 250 J/cm(2); and Group D: 4W/CW, 333 J/cm(2). Ten additional extracted human third molars were selected to prepare dentin discs. Each dentin disc was divided into two areas and was irradiated by 980-nm diode laser: Group E: control group, 0 J/cm(2); and Group F: 2.0 W/CW, 166 J/cm(2). The morphological alterations of the dentin surfaces and odontoblasts were examined with scanning electron microscopy (SEM), and the morphological alterations of the dental pulp tissue irradiated by laser were observed with an upright microscope. The study demonstrated that dentinal tubules can be entirely blocked after irradiation by 980-nm diode laser, regardless of the parameter setting. Diode laser with settings of 2.0 W and 980-nm sealed exposed dentin tubules effectively, and no significant morphological alterations of the pulp and odontoblasts were observed after irradiation. Irradiation with 980-nm diode laser could be effective for routine clinical treatment of DH, and 2.0W/CW (166 J/cm(2)) was a suitable energy parameter due to its rapid sealing of the exposed dentin tubules and its safety to the odontoblasts and pulp tissue.

In Vitro Study of Dentin Hypersensitivity Treated by 980-nm Diode Laser

Science.gov (United States)

Liu, Ying; Gao, Jie; Gao, Yan; XU, Shuaimei; Zhan, Xueling; Wu, Buling

2013-01-01

Introduction: To investigate the ultrastructural changes of dentin irradiated with 980-nm diode laser under different parameters and to observe the morphological alterations of odontoblasts and pulp tissue to determine the safety parameters of 980-nm diode laser in the treatment of dentin hypersensitivity (DH). Methods: Twenty extracted human third molars were selected to prepare dentin discs. Each dentin disc was divided into four areas and was irradiated by 980-nm diode laser under different parameters: Group A: control group, 0 J/cm2; Group B: 2 W/CW (continuous mode), 166 J/cm2; Group C: 3W/CW, 250 J/cm2; and Group D: 4W/CW, 333 J/cm2. Ten additional extracted human third molars were selected to prepare dentin discs. Each dentin disc was divided into two areas and was irradiated by 980-nm diode laser: Group E: control group, 0 J/cm2; and Group F: 2.0 W/CW, 166 J/cm2. The morphological alterations of the dentin surfaces and odontoblasts were examined with scanning electron microscopy (SEM), and the morphological alterations of the dental pulp tissue irradiated by laser were observed with an upright microscope. Results: The study demonstrated that dentinal tubules can be entirely blocked after irradiation by 980-nm diode laser, regardless of the parameter setting. Diode laser with settings of 2.0 W and 980-nm sealed exposed dentin tubules effectively, and no significant morphological alterations of the pulp and odontoblasts were observed after irradiation. Conclusions: Irradiation with 980-nm diode laser could be effective for routine clinical treatment of DH, and 2.0W/CW (166 J/cm2) was a suitable energy parameter due to its rapid sealing of the exposed dentin tubules and its safety to the odontoblasts and pulp tissue. PMID:25606318

Bio-reconstruction of root canal using dentin post

Directory of Open Access Journals (Sweden)

Navin Mishra

2013-01-01

Full Text Available This case report describes the successful management of complicated crown fracture of left maxillary central incisor (#21 of 23-year-old male using dentin (biological post made from human tooth. Endodontic treatment was initiated and sectional obturation was done using ProTaper gutta-percha and AH Plus sealer. The coronal space was modified to receive a human dentin post. A two-step procedure comprising direct and indirect technique of post fabrication was done to achieve the accuracy of biological post. A maxillary cuspid from an institutional tooth bank was taken, sectioned mesiodistally using a diamond disc simulating the length and thickness of mock post. Dentin post was first verified on the plaster model and then cemented in tooth #21. Core build up was done with composite and porcelain fused to metal (PFM crown was luted. On the follow-up visits, patient was asymptomatic and radiographic evaluation revealed normal periradicular architecture. Biological posts may be good alternatives to conventional post systems as they preserve internal dentin walls, provide excellent adhesion, and resilience similar to natural tooth structure.

Chemical treatment of the intra-canal dentin surface: a new approach to modify dentin hydrophobicity

Directory of Open Access Journals (Sweden)

Cesar GAITAN-FONSECA

2013-01-01

Full Text Available Objective This study evaluated the hydrophobicity of dentin surfaces that were modified through chemical silanization with octadecyltrichlorosilane (OTS. Material and Methods An in vitro experimental study was performed using 40 human permanent incisors that were divided into the following two groups: non-silanized and silanized. The specimens were pretreated and chemically modified with OTS. After the chemical modification, the dentin hydrophobicity was examined using a water contact angle measurement (WCA. The effectiveness of the modification of hydrophobicity was verified by the fluid permeability test (FPT. Results and Conclusions Statistically significant differences were found in the values of WCA and FPT between the two groups. After silanization, the hydrophobic intraradicular dentin surface exhibited in vitro properties that limit fluid penetration into the sealed root canal. This chemical treatment is a new approach for improving the sealing of the root canal system.

In vitro study of temperature changes in root during Er:YAG laser application; Estudo in vitro da alteracao da temperatura durante a aplicacao do Er:YAG laser intracanal

Energy Technology Data Exchange (ETDEWEB)

Brandao, Redson Vilela

2001-07-01

The temperature increase in root dentine irradiated by Er:YAG laser beam was analyzed, for different dentine thickness and different energy and frequency conditions, aiming the evaluation of Er:YAG laser in endodontic therapy, without causing any damages to close tissues. Twenty four human teeth were separated in four groups with six teeth each, and longitudinally sectioned in thickness of 0.5 mm (first group), 1,0 mm (second group), 1,5 mm (third group) and 2,0 mm (fourth group). Those samples were irradiated with the Er:YAG laser, emitting at the wavelength of 2.94{mu}m, by using a sapphire optic fiber with diameter of 0.375 mm, and forming an angle of 5 deg with the irradiated dentine surface. Three different laser energies were used in this study, 180 mJ, 160 mJ and 140 mJ, with frequencies of 10 Hz and 15 Hz. The temperature data were collected in a digital-analog system and sent to a computer for analysis. It was verified that the time for temperature increases of 5 deg in the external root walls varies according to the laser energy, repetition rate and dentine root thickness. Thus, in this work we could obtain laser parameters to avoid thermal damages in periodontal tissues. (author)

Marginal Gaps between 2 Calcium Silicate and Glass Ionomer Cements and Apical Root Dentin.

Science.gov (United States)

Biočanin, Vladimir; Antonijević, Đorđe; Poštić, Srđan; Ilić, Dragan; Vuković, Zorica; Milić, Marija; Fan, Yifang; Li, Zhiyu; Brković, Božidar; Đurić, Marija

2018-01-12

The outcome of periapical surgery has been directly improved with the introduction of novel material formulations. The aim of the study was to compare the retrograde obturation quality of the following materials: calcium silicate (Biodentine; Septodont, Saint-Maur-des-Fosses, France), mineral trioxide aggregate (MTA+; Cerkamed Company, Stalowa Wola, Poland), and glass ionomer cement (Fuji IX; GC Corporation, Tokyo, Japan). Materials' wettability was calculated concerning the contact angles of the cements measured using a glycerol drop. Cements' porosity was determined using mercury intrusion porosimetry and micro-computed tomographic (μCT) imaging. Extracted upper human incisors were retrofilled, and μCT analysis was applied to calculate the volume of the gap between the retrograde filling material and root canal dentin. Experiments were performed before and after soaking the materials in simulated body fluid (SBF). No statistically significant differences were found among the contact angles of the studied materials after being soaked in SBF. The material with the lowest nanoporosity (Fuji IX: 2.99% and 4.17% before and after SBF, respectively) showed the highest values of microporosity (4.2% and 3.1% before and after SBF, respectively). Biodentine had the lowest value of microporosity (1.2% and 0.8% before and after SBF, respectively) and the lowest value of microgap to the root canal wall ([10 ± 30] × 10 -3  mm 3 ). Biodentine and MTA possess certain advantages over Fuji IX for hermetic obturation of retrograde root canals. Biodentine shows a tendency toward the lowest marginal gap at the cement-to-dentin interface. Copyright © 2018 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

The effect of endodontic regeneration medicaments on mechanical properties of radicular dentin

Science.gov (United States)

Yassen, Ghaeth H.

Endodontic regeneration treatment of necrotic immature teeth has gained popularity in recent years. The approach suggests a biological alternative to induce a continuous root development. In this project, three in vitro experiments were conducted to investigate the effect of three medicaments used in endodontic regeneration on mechanical properties and chemical structure of radicular dentin. In the first experiment, we investigated longitudinally the effect of medicaments on the indentation properties of the root canal surface of immature teeth using a novel BioDent reference point indenter. A significant difference in the majority of indentation parameters between all groups was found after one-week and one-month application of medicaments (p double antibiotic paste (DAP) > control > calcium hydroxide [Ca(OH)2]. The four-week exposure of dentin to TAP and DAP caused 43% and 31% increase in total indentation distance outcome, respectively. In the second experiment, we investigated longitudinally the effect of medicaments on the chemical structure of immature radicular dentin by measuring the phosphate/amide I ratios of dentin using Attenuated Total Reflection Fourier Transform Infrared Spectroscopy. Phosphate/amide I ratios were significantly different between the four groups after one week, two weeks and four week application of medicaments (p untreated dentin > DAP-treated dentin > TAP-treated dentin. In the third experiment, we investigated longitudinally the effect of medicaments on root fracture resistance and microhardness of radicular dentin. For the microhardness, the two-way interaction between group and time was significant (pmedicaments caused significant decrease in fracture resistance ranging between 19%-30% after three month application compared to one week application. The three medicaments used in endodontic regeneration caused significant change in the chemical integrity of the superficial radicular dentin and significantly affected the indentation

Effect of calcium hydroxide and double and triple antibiotic pastes on the bond strength of epoxy resin-based sealer to root canal dentin.

Science.gov (United States)

Akcay, Merve; Arslan, Hakan; Topcuoglu, Hüseyin Sinan; Tuncay, Oznur

2014-10-01

The aim of this study was to evaluate the effects of calcium hydroxide (CH) and triple (TAP) and double (DAP) antibiotic pastes on the bond strength of an epoxy resin-based sealer (AH Plus Jet; Dentsply DeTrey, Konstanz, Germany) to the root canal dentin. Sixty-four single-rooted human mandibular premolars were decoronated and prepared using the rotary system to size 40. The specimens were randomly divided into a control group (without intracanal dressing) and 3 experimental groups that received an intracanal dressing with either CH, DAP, or TAP (n = 16). The intracanal dressing was removed by rinsing with 10 mL 17% EDTA followed by 10 mL 2.5% sodium hypochlorite. The root canals were then obturated with gutta-percha and AH Plus Jet sealer. A push-out test was used to measure the bond strength between the root canal dentin and the sealer. The data were analyzed using 2-way analysis of variance and Tukey post hoc tests to detect the effect of the independent variables (intracanal medicaments and root canal thirds) and their interactions on the push-out bond strength of the root canal filling material to the root dentin (P = .05). The push-out bond strength values were significantly affected by the intracanal medicaments (P .05). In the middle and apical third, the bond strength of the TAP group was higher than those of the CH and DAP groups (P < .05). The DAP and CH did not affect the bond strength of the epoxy resin-based sealer. Additionally, the TAP improved the bond strength of the epoxy resin-based sealer in the middle and apical thirds. Copyright © 2014 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Root canal preparation with Er:YSGG laser

Science.gov (United States)

Benthin, Hartmut; Ertl, Thomas P.; Onal, B.; Schruender, Stephan; Mueller, Gerhard J.

1994-12-01

The high level of efficiency of hard tissue ablation with Er:YAG and Er:YSGG lasers is well known. Of these lasers it is possible only to transmit Er:YSGG laser radiation with OH reduced quartz fibers. Most of the fibers we use in this study were prepared as hemispherical fiber tips. Fifty single rooted teeth were divided into ten groups (n equals 5). After conventional opening of the pulp chamber, root canal preparation was performed in five groups under water only using the laser. In the other five groups preparation with K-files to size 35 was performed before treatment with laser radiation. All teeth were axially separated with direct access to the root canal and examined in SEM investigations. The groups were compared by measuring the areas with patent dentin tubules. Representative areas were examined by TEM. The temperature at the root surface was measured during laser irradiation with thermocouples positioned at several points. The in-vitro study of the effect of the high delivered energy (50 - 100 mJ per pulse) in the root canal showed a good ablation effect. Most of the dentin tubules were opened. The increase in temperature at the root surface was tolerable.

Sodium Hypochlorite Irrigation and Its Effect on Bond Strength to Dentin

Directory of Open Access Journals (Sweden)

Tariq S. Abuhaimed

2017-01-01

Full Text Available Effective shaping and cleaning of root canals are essential for the success of endodontic treatment. Due to the complex anatomy of root canal spaces, the use of various instrumentation techniques alone is not effective in producing bacteria-free root canal spaces. Irrigation, disinfectants, rinses, and intervisit medications are used in conjunction with the mechanical instrumentation to ensure the success of endodontic treatment. Sodium hypochlorite (NaOCl, a halogenated compound, is routinely used to irrigate the root canal during endodontic treatments. NaOCl has been known for its antibacterial action, proteolytic and dissolution capacity, and debridement properties. NaOCl, however, can alter the composition of dentin and hence its interaction with the adhesive resins used to bond the restorative materials to treated dentin. This review therefore covers in depth the action of NaOCl on dentin-adhesive resin bond strength including both enhancement and reduction, then mechanisms proposed for such action, and finally how the adverse action of NaOCl on dentin can be reversed.

Sodium Hypochlorite Irrigation and Its Effect on Bond Strength to Dentin.

Science.gov (United States)

Abuhaimed, Tariq S; Abou Neel, Ensanya A

2017-01-01

Effective shaping and cleaning of root canals are essential for the success of endodontic treatment. Due to the complex anatomy of root canal spaces, the use of various instrumentation techniques alone is not effective in producing bacteria-free root canal spaces. Irrigation, disinfectants, rinses, and intervisit medications are used in conjunction with the mechanical instrumentation to ensure the success of endodontic treatment. Sodium hypochlorite (NaOCl), a halogenated compound, is routinely used to irrigate the root canal during endodontic treatments. NaOCl has been known for its antibacterial action, proteolytic and dissolution capacity, and debridement properties. NaOCl, however, can alter the composition of dentin and hence its interaction with the adhesive resins used to bond the restorative materials to treated dentin. This review therefore covers in depth the action of NaOCl on dentin-adhesive resin bond strength including both enhancement and reduction, then mechanisms proposed for such action, and finally how the adverse action of NaOCl on dentin can be reversed.

In vitro photodynamic antimicrobial chemotherapy in dentine contaminated by cariogenic bacteria

Science.gov (United States)

Melo, M. A. S.; de-Paula, D. M.; Lima, J. P. M.; Borges, F. M. C.; Steiner-Oliveira, C.; Nobre-Dos-Santos, M.; Zanin, I. C. J.; Barros, E. B.; Rodrigues, L. K. A.

2010-06-01

The development of a method to ensure bacterial-free substrates without extensive cavity preparation would be highly useful to dentistry, since there is no currently available effective method for killing residual bacteria in dentinal tissue. This randomized in vitro study determined parameters for using toluidine blue O (TBO) with a light-emitting diode (LED) for dentine caries disinfection and monitored intrapulpal/periodontal temperatures during irradiation. Occlusal human dentine slabs were immersed in Streptococcus mutans culture for demineralization induction. Slabs were allocated to 10 groups ( n = 15), which were treated with 0.1 mg ml-1 TBO with 5 min of incubation time or 0.9% NaCl solution for 5, 10 or 15 min, and submitted or not to irradiation for 5, 10 or 15 min (47, 94, and 144 J/cm2). Before and after treatments, dentine samples were analyzed with regard to S. mutans counts. In whole teeth, temperature in pulp and periodontium was measured by thermocouples during irradiation. Kruskal-Wallis/Student-Newman-Keuls, and ANOVA/Tukey test were respectively utilized to compare log reductions and temperature rises between groups. Bacterial reduction was observed when dentine was exposed to both TBO and LED at all irradiation times, as well as to LED alone for 10 and 15 min. Temperature increases lower than 2°C were observed for either pulp or periodontium. Concluding, LED combined with TBO is a safe and effective approach for dentine caries disinfection. Nevertheless, additional studies should be conducted to determine the influence of the irradiation in S. mutans viability in dentinal surface/tubules.

Incidence of apical root cracks and apical dentinal detachments after canal preparation with hand and rotary files at different instrumentation lengths.

Science.gov (United States)

Liu, Rui; Kaiwar, Anjali; Shemesh, Hagay; Wesselink, Paul R; Hou, Benxiang; Wu, Min-Kai

2013-01-01

The aim of this study was to compare the incidence of apical root cracks and dentinal detachments after canal preparation with hand and rotary files at different instrumentation lengths. Two hundred forty mandibular incisors were mounted in resin blocks with simulated periodontal ligaments, and the apex was exposed. The root canals were instrumented with rotary and hand files, namely K3, ProTaper, and nickel-titanium Flex K files to the major apical foramen (AF), short AF, or beyond AF. Digital images of the apical surface of every tooth were taken during the apical enlargement at each file change. Development of dentinal defects was determined by comparing these images with the baseline image. Multinomial logistic regression test was performed to identify influencing factors. Apical crack developed in 1 of 80 teeth (1.3%) with hand files and 31 of 160 teeth (19.4%) with rotary files. Apical dentinal detachment developed in 2 of 80 teeth (2.5%) with hand files and 35 of 160 teeth (21.9%) with rotary files. Instrumentation with rotary files terminated 2 mm short of AF and did not cause any cracks. Significantly less cracks and detachments occurred when instrumentation with rotary files was terminated short of AF, as compared with that terminated at or beyond AF (P hand instruments; instrumentation short of AF reduced the risk of dentinal defects. Copyright © 2013 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Deformation Behavior of Human Dentin under Uniaxial Compression

Directory of Open Access Journals (Sweden)

Dmitry Zaytsev

2012-01-01

Full Text Available Deformation behavior of a human dentin under compression including size and rate effects is studied. No difference between mechanical properties of crown and root dentin is found. It is mechanically isotropic high elastic and strong hard tissue, which demonstrates considerable plasticity and ability to suppress a crack growth. Mechanical properties of dentin depend on a shape of samples and a deformation rate.

Effect of MTA and Portland Cement on Fracture Resistance of Dentin

Directory of Open Access Journals (Sweden)

Maryam Forghani

2013-06-01

Full Text Available Background and aims. It is important to evaluate the effects of endodontic materials on tooth structures to avoid endodontic treatment failure. The aim of the present study was to investigate the effect of mineral trioxide aggregates (MTA and Portland cement (PC on fracture resistance of dentin. Materials and methods. Thirty-six freshly extracted human single-rooted premolar teeth were selected. The crowns were removed and the roots were randomly divided into two experimental groups and one control group. The root samples were longitudinally divided into two halves and a dentin bar (2×2×10 mm was cut from each root section for short-term (2 weeks and long-term (12 weeks evaluations. The root sections in the experimental groups were exposed to MTA or PC, while keeping the control group specimens in physiologic saline. The fracture resistance of each specimen was measured using an Instron testing machine. The results were statistically analyzed using ANOVA, a post hoc Tukey test and paired ttest at 5% significance level. Results. The fracture resistance of MTA-treated specimens significantly increased between 2 and 12 weeks (P0.05. Conclusion. The results showed that MTA increased the fracture resistance of root dentin, while PC had no significant effect on dentin fracture resistance.

Dispersion of near-infrared laser energy through radicular dentine when using plain or conical tips.

Science.gov (United States)

Teo, Christine Yi Jia; George, Roy; Walsh, Laurence J

2018-02-01

The aim of this study was to investigate the influence of tip design on patterns of laser energy dispersion through the dentine of tooth roots when using near-infrared diode lasers. Diode laser emissions of 810 or 940 nm were used in combination with optical fiber tips with either conventional plain ends or conical ends, to irradiate tooth roots of oval or round cross-sectional shapes. The lasers were operated in continuous wave mode at 0.5 W for 5 s with the distal end of the fiber tip placed in the apical or coronal third of the root canal at preset positions. Laser light exiting through the roots and apical foramen was imaged, and the extent of lateral spread calculated. There was a significant difference in infrared light exiting the root canal apex between plain and conical fiber tips for both laser wavelengths, with more forward transmission of laser energy through the apex for plain tips. For both laser wavelengths, there were no significant differences in emission patterns when the variable of canal shape was used and all other variables were kept the same (plain vs conical tip, tip position). To ensure optimal treatment effect and to prevent the risks of inadvertent laser effects on the adjacent periapical tissues, it is important to have a good understanding of laser transmission characteristics of the root canal and root dentine. Importantly, it is also essential to understand transmission characteristics of plain and conical fibers tips.

Incidence of apical root cracks and apical dentinal detachments after canal preparation with hand and rotary files at different instrumentation lengths

NARCIS (Netherlands)

Liu, R.; Kaiwar, A.; Shemesh, H.; Wesselink, P.R.; Hou, B.; Wu, M.K.

2013-01-01

Introduction The aim of this study was to compare the incidence of apical root cracks and dentinal detachments after canal preparation with hand and rotary files at different instrumentation lengths. Methods Two hundred forty mandibular incisors were mounted in resin blocks with simulated

The effect of warm air-blowing on the microtensile bond strength of one-step self-etch adhesives to root canal dentin.

Science.gov (United States)

Taguchi, Keita; Hosaka, Keiichi; Ikeda, Masaomi; Kishikawa, Ryuzo; Foxton, Richard; Nakajima, Masatoshi; Tagami, Junji

2018-02-01

The use of warm air-blowing to evaporate solvents of one-step self-etch adhesive systems (1-SEAs) has been reported to be a useful method. The purpose of this study was to evaluate the effect of warm air-blowing on root canal dentin. Four 1-SEAs (Clearfil Bond SE ONE, Unifil Core EM self-etch bond, Estelink, BeautiDualbond EX) were used. Each 1-SEA was applied to root canal dentin according to the manufacturers' instructions. After the adhesives were applied, solvent was evaporated using either normal air (23±1°C) or warm air (80±1°C) for 20s, and resin composite was placed in the post spaces. The air from the dryer, which could be used in normal- or hot-air-mode, was applied at a distance of 5cm above the root canal cavity in the direction of tooth axis. The temperature of the stream of air from the dryer in the hot-air-mode was 80±1°C, and in the normal mode, 23±1°C. After water storage of the specimens for 24h, the μTBS were evaluated at the coronal and apical regions. The μTBSs were statistically analyzed using three-way ANOVA and Student's t-test with Bonferroni correction (α=0.05). The warm air-blowing significantly increased the μTBS of all 1-SEAs at the apical regions, and also significantly increased the μTBS of two adhesives (Estelink and BeautiDualBond EX) at coronal regions. The μTBS of 1-SEAs to root canal dentin was improved by using warm air-blowing. Copyright © 2017 Japan Prosthodontic Society. Published by Elsevier Ltd. All rights reserved.

Effect of Different Torque Settings on Crack Formation in Root Dentin.

Science.gov (United States)

Dane, Asım; Capar, Ismail Davut; Arslan, Hakan; Akçay, Merve; Uysal, Banu

2016-02-01

The aim of the present study was to observe the incidence of cracks in root canal dentin using the ProTaper Universal system (Dentsply Maillefer, Ballaigues, Switzerland) at low- and high-torque settings. Sixty-nine mandibular premolar teeth that had been extracted for different reasons were selected. The teeth were divided into 3 groups: an unprepared control group, a low-torque settings group (SX = 3, S1 = 2, S2 = 1, F1 = 1.5, F2 = 2, F3 = 2, F4 = 2 N/cm), and a high-torque settings group (SX = 4, S1 = 4, S2 = 1.5, F1 = 2, F2 = 3, F3 = 3, F4 = 3 N/cm). After a root canal procedure, all the teeth were horizontally sectioned at 2, 4, 6, and 8 mm from the apex. Then, under a stereomicroscope, all the slices were examined to determine the presence of cracks. A chi-square test was used for data analysis. The significance level was set at P = .05. There were no cracks in the unprepared control group. Vertical root fractures were not observed in any of the groups. There were significantly fewer cracks (17.4% of the sections) in the low-torque group than in the high-torque group (29.4% of the sections) (P torque than at low-torque settings. Copyright © 2016 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Effect of photon-initiated photoacoustic streaming on removal of apically placed dentinal debris.

Science.gov (United States)

Arslan, H; Capar, I D; Saygili, G; Gok, T; Akcay, M

2014-11-01

To compare the efficacy of photon-induced photoacoustic streaming (PIPS) technique with conventional, sonic and ultrasonic irrigation on the removal of apically placed dentinal debris from an artificial groove created in a root canal. Root canal preparation was performed up to size 40 on 48 extracted single-rooted teeth using ProTaper rotary instruments. The specimens were then split longitudinally, and a standardized groove was prepared in the apical part of each segment. Each groove was filled with dentinal debris mixed with 5% NaOCl. Each tooth was reassembled and irrigated as follows: (i) conventional irrigation with 1% NaOCl, (ii) sonic, (iii) ultrasonic irrigation, and (iv) PIPS. The root segments were disassembled, and the amount of remaining dentinal debris was evaluated under a stereomicroscope at 20× magnification, using a four-grade scoring system. The data were evaluated statistically using Kruskal-Wallis and Mann-Whitney U-tests with a 95% confidence level (P = 0.05). Photon-induced photoacoustic streaming removed significantly more dentinal debris than conventional irrigation (P streaming was more effective than conventional, sonic and ultrasonic irrigation in the removal of apically placed dentinal debris. © 2014 International Endodontic Journal. Published by John Wiley & Sons Ltd.

Effect of Enamel and Dentin Irradiation by Gamma Rays on the Bond Strength of Two Adhesive Restorations

International Nuclear Information System (INIS)

Zein, N.S.A.

2014-01-01

There have been many reports related to the high incidence of the head and neck cancers including those of the oral cavity. Ablative surgery, radiotherapy, chemotherapy and reconstructive surgery are components of the curative or palliative treatment of head and neck cancers which are intended to improve survival time and quality of life. In addition to the desirable anticancer effects, ionizing radiation causes damage to normal tissues located within the irradiation fields (1). The early responses of teeth to irradiation include dental hypersensitivity and spontaneous pain (2). Several types of desensitizers may be applied to the tooth after cavity preparation in an attempt to manage dental hypersensitivity. The most common form of management is the placement of a topically applied agent either by a dental professional or by the patient at home. These agents stimulate mineral deposition or occlude dental tubules to reduce hypersensitivity (3,4). Radiation caries is another irradiation-related damage to dental structures. It remains the most threatening complication of radiotherapy for the dentition. It is a highly destructive form of dental caries with a rapid onset and progression. Radiation caries may become evident as early as three months following the initiation of head and neck radiotherapy. In severe cases, a previously healthy dentition can be completely lost within a year (5). Radiation caries involves both enamel and dentin; it tends to first affect the cervical and incisal edges of the teeth. Beside the irradiation-induced xerostomia, the effect of irradiation on dental hard tissues may be an important factor in radiation caries. Studies have reported the physical and chemical changes in enamel after radiotherapy, which are a direct consequence of the irradiation treatment. For dentin, a significant reduction in microhardness is observed after irradiation accompanied by reduced stability of the dentino-enamel junction (DEJ) The oral environment of head

Evaluation of the tensile bond strength of an adhesive system self-etching in dentin irradiated with Er:YAG laser

International Nuclear Information System (INIS)

Mello, Andrea Malluf Dabul de

2000-01-01

Since Buonocore (1955), several researchers have been seeking for the best adhesive system and treatment for the enamel and dentin surfaces. The use of the acid has been presented as one of the best techniques of dentin conditioning , because this promotes the removal of the 'smear layer and exhibition of dentinal structure, for a best penetration and micro- retention of the adhesive system. However, some conditioning methods have been appearing in the literature, for the substitution or interaction with the acid substances, as the laser. The objective of this work is to evaluate the tensile bond strength of the adhesive system self-etching' associated to a composed resin, in dentin surfaces conditioned with the Er:YAG laser. For this study, freshly extracted human teeth were used and in each one the dentinal surfaces , which were treated with three sandpapers of different granulations (120,400,600), to obtain a standard of the smear layer, before the irradiation of the laser and of the restoring procedure. After these procedures the specimens were storage in distilled water at 37 deg C for 24 hours. Soon after, they were submitted to the tensile strength test .After analyzing the results, we can concluded that the use of the Er:YAG laser can substitute the drill without the need of conditioning, when using the adhesive system 'self-etching' in the dentinal surfaces because there was a decline in the strength of adhesion in the groups conditioned with the laser. (author)

In vitro evaluation of the morphologic changes on the root dentine irradiated by CO{sub 2} laser associated or not to calcium hydroxide application; Avaliacao in vitro das alteracoes morfologicas da superficie da dentina radicular irradiada pelo laser de CO{sub 2} associado ou nao a aplicacao de hidroxido de calcio

Energy Technology Data Exchange (ETDEWEB)

Romano, Ana Cristina Cury Camargo

2003-07-01

This in vitro study has evaluated the structural changes on the root dentine irradiated by a CO{sub 2} laser associated or not to calcium hydroxide application, from the irradiated surface analysis by means of Scanning Electronic Microscopy (SEM). The purpose of this evaluation has been the study of an alternative method for the treatment of dentine hypersensitivity. Fourteen human teeth were utilized, third molars, divided into 7 groups. Group I (control group) to which no treatment was applied; Groups II, III and IV were given an application of Ca (OH){sub 2} paste followed by C0{sub 2} laser irradiation, lasting 5 seconds each with intervals of 10 seconds between each application, with continuous emission, power of 0.5 W (Group II), 1.0 W (Group III), and 1.5 W (Group IV); Groups V, VI, and VII were given laser irradiations without the Ca (OH){sub 2} paste following the same parameters applied to groups II, III, and IV respectively. Morphologic changes suggesting to fusion and re-solidification have been observed, as well as the presence of material obstructing the whole analyzed surface on groups II, III, and IV (laser + Ca (OH){sub 2}). As for groups V, VI, and VII, it has been observed fusion, re-solidification, and cracks, and these results being statistically significant when compared the '(Ca (OH){sub 2})' groups to the laser groups. No statistically significant differences were observed regarding the different powers applied in the groups that used the same treatment. Despite this result, it can be stated that powers above 1.0 W (DP = 125,38 W/cm{sup 2}) are unfavorable due to the undesirable morphologic alterations and aesthetic compromising. (author)

In vitro evaluation of the morphologic changes on the root dentine irradiated by CO{sub 2} laser associated or not to calcium hydroxide application; Avaliacao in vitro das alteracoes morfologicas da superficie da dentina radicular irradiada pelo laser de CO{sub 2} associado ou nao a aplicacao de hidroxido de calcio

Energy Technology Data Exchange (ETDEWEB)

Romano, Ana Cristina Cury Camargo

2003-07-01

This in vitro study has evaluated the structural changes on the root dentine irradiated by a CO{sub 2} laser associated or not to calcium hydroxide application, from the irradiated surface analysis by means of Scanning Electronic Microscopy (SEM). The purpose of this evaluation has been the study of an alternative method for the treatment of dentine hypersensitivity. Fourteen human teeth were utilized, third molars, divided into 7 groups. Group I (control group) to which no treatment was applied; Groups II, III and IV were given an application of Ca (OH){sub 2} paste followed by C0{sub 2} laser irradiation, lasting 5 seconds each with intervals of 10 seconds between each application, with continuous emission, power of 0.5 W (Group II), 1.0 W (Group III), and 1.5 W (Group IV); Groups V, VI, and VII were given laser irradiations without the Ca (OH){sub 2} paste following the same parameters applied to groups II, III, and IV respectively. Morphologic changes suggesting to fusion and re-solidification have been observed, as well as the presence of material obstructing the whole analyzed surface on groups II, III, and IV (laser + Ca (OH){sub 2}). As for groups V, VI, and VII, it has been observed fusion, re-solidification, and cracks, and these results being statistically significant when compared the '(Ca (OH){sub 2})' groups to the laser groups. No statistically significant differences were observed regarding the different powers applied in the groups that used the same treatment. Despite this result, it can be stated that powers above 1.0 W (DP = 125,38 W/cm{sup 2}) are unfavorable due to the undesirable morphologic alterations and aesthetic compromising. (author)

Influence of multi-wavelength laser irradiation of enamel and dentin surfaces at 0.355, 2.94, and 9.4 μm on surface morphology, permeability, and acid resistance.

Science.gov (United States)

Chang, Nai-Yuan N; Jew, Jamison M; Simon, Jacob C; Chen, Kenneth H; Lee, Robert C; Fried, William A; Cho, Jinny; Darling, Cynthia L; Fried, Daniel

2017-12-01

Ultraviolet (UV) and infrared (IR) lasers can be used to specifically target protein, water, and mineral, respectively, in dental hard tissues to produce varying changes in surface morphology, permeability, reflectivity, and acid resistance. The purpose of this study was to explore the influence of laser irradiation and topical fluoride application on the surface morphology, permeability, reflectivity, and acid resistance of enamel and dentin to shed light on the mechanism of interaction and develop more effective treatments. Twelve bovine enamel surfaces and twelve bovine dentin surfaces were irradiated with various combinations of lasers operating at 0.355 (Freq.-tripled Nd:YAG (UV) laser), 2.94 (Er:YAG laser), and 9.4 μm (CO 2 laser), and surfaces were exposed to an acidulated phosphate fluoride gel and an acid challenge. Changes in the surface morphology, acid resistance, and permeability were measured using digital microscopy, polarized light microscopy, near-IR reflectance, fluorescence, polarization sensitive-optical coherence tomography (PS-OCT), and surface dehydration rate measurements. Different laser treatments dramatically influenced the surface morphology and permeability of both enamel and dentin. CO 2 laser irradiation melted tooth surfaces. Er:YAG and UV lasers, while not melting tooth surfaces, showed markedly different surface roughness. Er:YAG irradiation led to significantly rougher enamel and dentin surfaces and led to higher permeability. There were significant differences in acid resistance among the various treatment groups. Surface dehydration measurements showed significant changes in permeability after laser treatments, application of fluoride and after exposure to demineralization. CO 2 laser irradiation was most effective in inhibiting demineralization on enamel while topical fluoride was most effective for dentin surfaces. Lasers Surg. Med. 49:913-927, 2017. © 2017 Wiley Periodicals, Inc. © 2017 Wiley Periodicals, Inc.

Effect of Self-Adhesive and Separate Etch Adhesive Dual Cure Resin Cements on the Bond Strength of Fiber Post to Dentin at Different Parts of the Root

Directory of Open Access Journals (Sweden)

Ehsan Mohamadian Amiri

2017-10-01

Full Text Available Objectives: Bonding of fiber posts to intracanal dentin is challenging in the clinical setting. This study aimed to compare the effect of self-adhesive and separate etch adhesive dual cure resin cements on the bond strength of fiber post to dentin at different parts of the root.Materials and Methods: This in-vitro experimental study was conducted on 20 single-rooted premolars. The teeth were decoronated at 1mm coronal to the cementoenamel junction (CEJ, and the roots underwent root canal treatment. Post space was prepared in the roots. Afterwards, the samples were randomly divided into two groups. In group 1, the fiber posts were cemented using Rely X Unicem cement, while in group 2, the fiber posts were cemented using Duo-Link cement, according to the manufacturer's instructions. The intracanal post in each root was sectioned into three segments of coronal, middle, and apical, and each cross-section was subjected to push-out bond strength test at a crosshead speed of 1mm/minute until failure. Push-out bond strength data were analyzed using independent t-test and repeated measures ANOVA.Results: The bond strength at the middle and coronal segments in separate etch adhesive cement group was higher than that in self-adhesive cement group. However, the bond strength at the apical segment was higher in self-adhesive cement group compared to that in the other group. Overall, the bond strength in separate etch adhesive cement group was significantly higher than that in self-adhesive cement group (P<0.001.Conclusions: Bond strength of fiber post to intracanal dentin is higher after the use of separate etch adhesive cement compared to self-adhesive cement.

Thermal stress in dentin and enamel under CO2 laser irradiation

Science.gov (United States)

Meyer, Dirk H.; Foth, Hans-Jochen

1996-01-01

Ablation of dentin and tartar was studied under carbon dioxide-laser irradiation in cw and pulse mode with pulse length down to 150 microseconds. The specimens had been cut by a diamant blade to slices of thicknesses between 0.8 and 2.8 mm. The laser induced temperature rise was measured by an infrared camera monitoring the backside of the samples. The specimens shape and structure at the laser spot was analyzed by electron microscopy. Of special interest was the testing of the SwiftLaseTM to reducing the heat. The experimental results show the necessity of a water cooling in all application modes. The origin of the cracks which had been observed in many of the samples, is currently under investigation.

Variation on Molecular Structure, Crystallinity, and Optical Properties of Dentin Due to Nd:YAG Laser and Fluoride Aimed at Tooth Erosion Prevention

Science.gov (United States)

Freitas, Anderson Z.; Bachmann, Luciano; Benetti, Carolina; Ana, Patricia A.

2018-01-01

This in vitro study evaluated the compositional, crystalline, and morphological effects promoted by Nd:YAG laser on root dentin, and verified the effects of laser and topical acidulated phosphate fluoride application (APF-gel) on dentin erosion. 180 bovine dentin slabs were randomized into 4 groups (n = 45): G1–untreated, G2–APF-gel (1.23% F−, 4 min), G3–Nd:YAG (1064 nm, 84.9 J/cm2, 10 Hz), and G4–APF-gel application followed by Nd:YAG laser irradiation. The compositional, crystalline, and morphological effects promoted by treatments were investigated on five samples of each experimental group. The other samples were submitted to a 5-day, 10-day, or 15-day erosive and abrasive demineralization and remineralization cycling in order to create erosion lesions. The area and depth of lesions, as well as the optical attenuation coefficient, were assessed, and all data were statistically analysed (p laser promoted the reduction of carbonate, the formation of tetracalcium phosphate, as well as the melting and recrystallization of the dentin surface. Laser significantly decreased the area and depth of erosion lesions and altered the optical attenuation coefficient when compared to untreated and APF-gel groups, but the association of APF-gel and laser did not promote an additional effect. Nd:YAG laser irradiation can be a promissory treatment to prevent dentin erosion and the abrasion process. PMID:29389868

Effects of nanosilver and nanozinc incorporated mesoporous calcium-silicate nanoparticles on the mechanical properties of dentin.

Directory of Open Access Journals (Sweden)

Jie Zhu

Full Text Available Mesoporous calcium-silicate nanoparticles (MCSNs are advanced biomaterials for drug delivery and mineralization induction. They can load silver and exhibit significantly antibacterial effects. However, the effects of MCSNs and silver-loaded MCSNs on dentin are unknown. The silver (Ag and/or zinc (Zn incorporated MCSNs (Ag-Zn-MCSNs were prepared by a template method, and their characterizations were tested. Then the nanoparticles were filled into root canals and their effects on the dentin were investigated. Ag-Zn-MCSNs showed characteristics of mesoporous materials and sustained release of ions over time. Ag-Zn-MCSNs adhered well to the root canal walls and infiltrated into the dentinal tubules after ultrasound activation. Ag-Zn-MCSNs showed no significantly negative effects on either the flexural strength or the modulus of elasticity of dentin, while CH decreased the flexural strength of dentin significantly (P<0.05. These findings suggested that Ag and Zn can be incorporated into MCSNs using a template method, and the Ag-Zn-MCSNs may be developed into a new disinfectant for the root canal and dentinal tubules.

Light-emitting diode assessment of dentinal defects: the role of presumed extraction forces

Directory of Open Access Journals (Sweden)

Marcelo Santos Coelho

2017-07-01

Full Text Available Objectives The evaluation of iatrogenic dentinal defects in extracted teeth may be influenced by extraction forces and prolonged dry times. The purpose of this study was to compare the presence of dentinal defects in freshly extracted, periodontally compromised teeth with those in a group of teeth with uncontrolled extraction forces and storage time. Materials and Methods The experimental group consisted of eighteen roots obtained from teeth extracted due to periodontal reasons with class II or III mobility. They were kept in saline and sectioned within 1 hour following extraction. The control group consisted of matched root types obtained from an anonymous tooth collection, consistent with previous dentinal defect studies. The slices were obtained at 3, 6, and 9 mm from the apex. The imaging process exposed all specimens to no more than 60 seconds of dry time. The × 12.8 magnification was used for the 9 mm slices and × 19.2 magnification for the 3 mm and 6 mm slices under light-emitting diode (LED transillumination. The root canal spaces and periodontal tissues were masked to minimize extraneous factors that might influence the evaluators. Chi-square test was used for statistical analysis. Results Dentinal defects were detected in 17% of the experimental group teeth, compared to 61% of control teeth (p = 0.015. Conclusions LED transillumination assessment of freshly extracted roots with class II or III mobility showed smaller number of dentinal defects than roots with uncontrolled storage time and extraction forces. The use of freshly extracted roots with mobility should be considered for future dental defect assessment studies.

Scanning electron microscopy evaluation of the interaction pattern between dentin and resin after cavity preparation using Er:YAG laser

International Nuclear Information System (INIS)

Schein, Marcelo Thome

2001-01-01

The aim of this study was to describe the interaction pattern formed between dentin and resin on cavities prepared with an erbium laser (Er:YAG). The morphological aspect of the irradiated dentin after acid etching was also observed. Ten dentin disks were obtained from fresh extracted third molars. Each disk received two cavities, one prepared with a conventional high-speed drill, while the other cavity was obtained by the use of an Er:YAG laser (KaVo KEY Laser, KaVo Co.). The laser treatment was performed with 250 mJ/pulse, 4 Hz, non contact mode, focused beam, and a fine water mist was used. Five disks were prepared for morphological analysis of the acid etched dentin. The other five disks had their cavities restored with Single Bond (3M) followed by Z100 resin (3M). The specimens were observed under scanning electron microscopy after dentin-resin interface demineralization and deproteinization. It was observed that the morphological characteristics of the acid-etched irradiated dentin were not favorable to the diffusion of monomers through the collagen network. The dentin resin interfacial aspect of irradiated dentin, after acid etching, showed thin tags and scarce hybridization zones, which agreed with the morphology of the irradiated and acid-etched dentin substrate observed. (author)

Apical microinfiltration evaluation of radicular channels irradiated with Er:YAG laser in vitro; Avaliacao da microinfiltracao apical de condutos radiculares irradiados in vitro com laser de Er:YAG

Energy Technology Data Exchange (ETDEWEB)

Sebrao, Catia Cilene Nass

2003-07-01

It was evaluated, in vitro, the adaptation of the filling material (Sealer 2S{sup R}) to the root channels dentine walls treated using the endodontic technique and prepared with the Er:YAG laser, by the technique of infiltration of methylene blue dye. Using scanning electronic microscopy, the morphologic alteration of the root channel dentine was observed for one sample per studied group. Also, an evaluation of the temperature increase in the external surface of the root during the irradiations was performed for two samples per group. For each group of samples, with eleven roots each, two sub-groups had been considered: the dry, irradiated after completely dry with absorbent cones of paper, and the humid, where a cone of absorbent paper was applied for two seconds in the root canal, leaving them lightly humidified. Considering the used energies for the irradiations, the groups are: G1, control (without irradiation), G2-dry (100 mJ-10 Hz), G2-humid (100 mJ-10 Hz), G3-dry (140 mJ-6 Hz), G3-humid (140 mJ-6 Hz), G4-dry (180 mJ-6 Hz), and G4-humid (180 mJ-6 Hz). The results had shown that apical microinfiltration did not exhibit significant difference among groups. The highest increase in temperature was observed for the dry groups, with the maximum variation of temperature of 6.5 deg C. Under the scanning electronic microscopy analysis, the humid groups had presented cleaner surfaces than the dry groups. The G4-humid group presented extensive regions of fusion and resolidification of the dentine. (author)

A micro-computed tomographic evaluation of dentinal microcrack alterations during root canal preparation using single-file Ni-Ti systems.

Science.gov (United States)

Li, Mei-Lin; Liao, Wei-Li; Cai, Hua-Xiong

2018-01-01

The aim of the present study was to evaluate the length of dentinal microcracks observed prior to and following root canal preparation with different single-file nickel-titanium (Ni-Ti) systems using micro-computed tomography (micro-CT) analysis. A total of 80 mesial roots of mandibular first molars presenting with type II Vertucci canal configurations were scanned at an isotropic resolution of 7.4 µm. The samples were randomly assigned into four groups (n=20 per group) according to the system used for root canal preparation, including the WaveOne (WO), OneShape (OS), Reciproc (RE) and control groups. A second micro-CT scan was conducted after the root canals were prepared with size 25 instruments. Pre- and postoperative cross-section images of the roots (n=237,760) were then screened to identify the lengths of the microcracks. The results indicated that the microcrack lengths were notably increased following root canal preparation (Pfiles. Among the single-file Ni-Ti systems, WO and RE were not observed to cause notable microcracks, while the OS system resulted in evident microcracks.

Effect of gamma-ray irradiation on starch in sweet popato roots

International Nuclear Information System (INIS)

Hayashi, T.; Todoroki, S.

1994-01-01

Starch contents, as well as the size and molecular weight, in sweet potato roots decreased during steerage at 30 degrees C after gamma-ray irradiation, accompanying the increase of sucrose content. No change in the starch and sucrose contents was observed in unirradiated specimens. By microscopy damaged starch granules were observed only in gamma-ray irradiated root. The results suggested that starch was converted into sucrose unirradiated sweet potato roots by the enzymes responsible for starch-sugar interconversion of which the activities were enhanced by gamma-ray irradiation

Comparative evaluation of dentinal crack formation after root canal preparation using ProTaper Next, OneShape, and Hyflex EDM.

Science.gov (United States)

Das, Sanjib; Pradhan, Prasanti Kumari; Lata, S; Sinha, Sachidananda Prasad

2018-01-01

The purpose of this study was to compare the incidence of dentinal crack formation after root canal preparation using ProTaper Next, OneShape, and Hyflex electrodischarge machining (HEDM). A total of 75 extracted mandibular premolars were selected. The root canals were instrumented using ProTaper Next, OneShape, and HEDM rotary files. All roots were horizontally sectioned at 3, 6, and 9 mm from apex with slow-speed saw under water cooling. The sections were observed under a stereomicroscope at ×25 to determine the absence or presence of crack. Data were analyzed using post hoc test and one-way ANOVA. ProTaper Next and HEDM produced significantly less cracks than OneShape. Within the limitation of this in vitro study, it can be concluded that nickel-titanium instruments may cause cracks on the root surface. ProTaper Next and HEDM tend to produce less number of cracks as compared to OneShape.

Stereomicroscopic evaluation of dentinal defects induced by new rotary system: "ProTaper NEXT".

Science.gov (United States)

Shori, Deepa Deepak; Shenoi, Pratima Ramakrishna; Baig, Arshia R; Kubde, Rajesh; Makade, Chetana; Pandey, Swapnil

2015-01-01

The objective of this study was to evaluate dentinal defects formed by new rotary system - Protaper next™ (PTN). Sixty single-rooted premolars were selected. All specimens were decoronated and divided into four groups, each group having 15 specimens. Group I specimens were prepared by Hand K-files (Mani), Group II with ProTaper Universal (PT; Dentsply Maillefer), Group III with Hero Shaper (HS; Micro-Mega, Besancon, France), and Group IV with PTN (Dentsply Maillefer). Roots of each specimen were sectioned at 3, 6, and 9mm from the apex and were then viewed under a stereomicroscope to evaluate presence or absence of dentinal defects. In roots prepared with hand files (HFs) showed lowest percentage of dentinal defects (6.7%); whereas in roots prepared with PT, HS, and PTN it was 40, 66.7, and 26.7%, respectively. There was significant difference between the HS group and the PTN group (P hand instruments induced minimal defects.

Dentinal Dysplasia Type I: A Case Report with a 6-Year Followup

Directory of Open Access Journals (Sweden)

Sezin Ozer

2013-01-01

Full Text Available Introduction. Dentin dysplasia is a rare disturbance of dentin formation characterized by normal enamel but atypical dentin formation with abnormal pulpal morphology that is inherited as an autosomal pulpal morphology. Case Presentation. A 7-year-old female who had problems in chewing function was referred to Oral and Maxillofacial Surgery Department at the Faculty of Dentistry in Ondokuz Mayıs University. In the radiographic examination, it was determined that some of the unerupted permanent teeth of the patient had short, blunted, and malformed roots with obliterated pulp chambers, although the bone below the teeth showed well-defined margins. This unusual case of generalized short roots presents a case demonstrating both classic and atypical features of dentinal dysplasia type I (DDI in the mixed and permanent dentitions. Conclusion. There are still many issues in the diagnosis and management of patients with dentin dysplasia. Early diagnosis, clinical and radiographic findings, as well as treatment of this condition and the initiation of effective preventive strategies may help prevent or delay loss of dentition.

Dentin hypersensitivity clinical study comparing LILT and LEDT keeping the same irradiation parameters

International Nuclear Information System (INIS)

Lizarelli, R F Z; Miguel, F A C; Bagnato, V S; Freitas-Pontes, K M; Villa, G E P; Nunez, S C

2010-01-01

Dentin hypersensitivity is a common condition associated with high dental pain. A new LED-based (light emitting diode) light source has been used as an experimental tool in some studies. Purpose: The main objective was to compare these two light sources emitting in the same spectral band (red – from 625 to 660 nm) to promote pain relief. Material and methods: A total of 6 sessions were accomplished, being three irradiation sessions and three follow-up sessions. This single-blind study compared a control group (Placebo) and two other groups with different equipments: low laser intensity treatment (LILT) and a light emitting diode system treatment (LEDT). Results: The results showed that there is no statistical difference between LILT and LEDT groups, however, both were better than control group (p ≤ 0.01) in terms of treatment efficiency; there is no difference between the second and the third sessions for both treatment, it means that the third session was not necessary; finally, the improvement at the end of the entire research (follow up care of 30 days) was very expressive in comparison to pre-treatment situation for all teeth (p ≤ 0.01). Conclusion: LILT and LEDT were equally effective to treat dentine hypersensitivity, a 3rd treatment session was not necessary/two sessions are enough

Comparison of bond strength of different endodontic sealers to root dentin: An in vitro push-out test.

Science.gov (United States)

Madhuri, G Vijaya; Varri, Sujana; Bolla, Nagesh; Mandava, Pragna; Akkala, Lakshmi Swathi; Shaik, Jaheer

2016-01-01

To compare the bond strength of four different endodontic sealers to root dentin through push-out test design. Forty single-rooted teeth with completely formed apices were selected. Teeth were decoronated, and working length was determined. Instrumentation and irrigation were performed. The teeth were divided into four groups based upon the sealer used. Group 1: Bioceramic sealer (Endosequence), Group 2: Mineral trioxide aggregate (MTA) based sealer (MTA Fill apex), Group 3: Epoxy resin based sealer (MM-Seal), and Group 4: Dual cure resin-based sealer (Hybrid Root Seal). Manipulation and application of the sealer was done as per the manufacturer instructions. All the teeth were obturated using 6% gutta-percha. After obturation, each tooth was prepared for push-out test with root slices of 2 mm thickness using universal testing machine. The highest bond strength was found in Group 1 (Endosequence) (P strength was found in Group 2 (MTA Fill apex). Statistical analysis is done by two-way ANOVA and Newman-Keuls multiple post hoc. The push-out bond strength of Bioceramic sealer was highest followed by resin-based sealer and lowest bond strength was observed in MTA-based sealer.

Stereomicroscopic evaluation of dentinal defects induced by new rotary system: “ProTaper NEXT”

Science.gov (United States)

Shori, Deepa Deepak; Shenoi, Pratima Ramakrishna; Baig, Arshia R; Kubde, Rajesh; Makade, Chetana; Pandey, Swapnil

2015-01-01

Introduction: The objective of this study was to evaluate dentinal defects formed by new rotary system — Protaper next™ (PTN). Materials and Methods: Sixty single-rooted premolars were selected. All specimens were decoronated and divided into four groups, each group having 15 specimens. Group I specimens were prepared by Hand K-files (Mani), Group II with ProTaper Universal (PT; Dentsply Maillefer), Group III with Hero Shaper (HS; Micro-Mega, Besancon, France), and Group IV with PTN (Dentsply Maillefer). Roots of each specimen were sectioned at 3, 6, and 9mm from the apex and were then viewed under a stereomicroscope to evaluate presence or absence of dentinal defects. Results: In roots prepared with hand files (HFs) showed lowest percentage of dentinal defects (6.7%); whereas in roots prepared with PT, HS, and PTN it was 40, 66.7, and 26.7%, respectively. There was significant difference between the HS group and the PTN group (P hand instruments induced minimal defects. PMID:26069406

Nonsurgical management of horizontal root fracture associated external root resorption and internal root resorption

Directory of Open Access Journals (Sweden)

Shiraz Pasha

2016-01-01

Full Text Available Horizontal root fractures, which frequently affect the upper incisors, usually result from a frontal impact. As a result, combined injuries occur in dental tissues such as the pulp, dentin, cementum, periodontal ligament, and alveolar bone. Internal root canal inflammatory resorption involves a progressive loss of intraradicular dentin without adjunctive deposition of hard tissues adjacent to the resorptive sites. It is frequently associated with chronic pulpal inflammation, and bacteria might be identified from the granulation tissues when the lesion is progressive to the extent that it is identifiable with routine radiographs. With the advancement in technology, it is imperative to use modern diagnostic tools such as cone beam computed tomography and radiovisuography to diagnose and confirm the presence and extent of resorptions and fractures and their exact location. This case report presents a rare case having internal root resorption and horizontal root fracture with external inflammatory root resorption both which were treated successfully following guidelines by International Association of Dental Traumatology by nonsurgical treatment with 1 year follow-up.

Gamma ray irradiation to roots of tea-plants and induced mutant system

International Nuclear Information System (INIS)

Takeda, Yoshiyuki; Nekaku, Koji; Wada, Mitsumasa

1990-01-01

In order to utilize the useful mutation which is induced by irradiation for the breeding of tea-plants, the gamma-ray irradiation to the roots of tea-plants was carried out. The samples were the roots of tea-plants of four varieties dug up in February, 1984, and were adjusted to about 20 cm, then, put in the cold storage at 5degC for 9 months till the time of irradiation in November, 1984. However, a part of them was taken out in August, and planted in a field for 76 days to germinate, thereafter, used as the samples. The gamma-ray from a Co-60 source was irradiated in the radiation breeding laboratory of Agriculture Bioresources Research Institute at the total dose of 1, 2 and 3 kR and the dose rate of 500 R/h. The irradiated roots were planted as they are or in the state of being cut, and the rate of germination, the number of buds and the induced mutation were examined. Clear difference was not observed in the rate of germination and the number of buds between the irradiated samples and those without irradiation. The long roots were superior to the short roots regarding these items. The types of the induced mutation were mostly thin leaves, and also yellowing, mottling, fascination and so on occurred. The mutant system lacking trichomes on the back of new leaves is considered to be strong against tea anthracnose, and is valuable. (K.I.)

Gamma ray irradiation to roots of tea-plants and induced mutant system

Energy Technology Data Exchange (ETDEWEB)

Takeda, Yoshiyuki; Nekaku, Koji; Wada, Mitsumasa (National Research Inst. of Vegetables, Ornamental Plants and Tea, Ano, Mie (Japan))

1990-11-01

In order to utilize the useful mutation which is induced by irradiation for the breeding of tea-plants, the gamma-ray irradiation to the roots of tea-plants was carried out. The samples were the roots of tea-plants of four varieties dug up in February, 1984, and were adjusted to about 20 cm, then, put in the cold storage at 5degC for 9 months till the time of irradiation in November, 1984. However, a part of them was taken out in August, and planted in a field for 76 days to germinate, thereafter, used as the samples. The gamma-ray from a Co-60 source was irradiated in the radiation breeding laboratory of Agriculture Bioresources Research Institute at the total dose of 1, 2 and 3 kR and the dose rate of 500 R/h. The irradiated roots were planted as they are or in the state of being cut, and the rate of germination, the number of buds and the induced mutation were examined. Clear difference was not observed in the rate of germination and the number of buds between the irradiated samples and those without irradiation. The long roots were superior to the short roots regarding these items. The types of the induced mutation were mostly thin leaves, and also yellowing, mottling, fascination and so on occurred. The mutant system lacking trichomes on the back of new leaves is considered to be strong against tea anthracnose, and is valuable. (K.I.).

The effect of 17% EDTA and MTAD on smear layer removal and on erosion of root canal dentin when used as final rinse: An in vitro SEM study

Directory of Open Access Journals (Sweden)

Vishal A Mahajan

2010-01-01

Full Text Available Background: The aim of the present study was to evaluate and compare the ability of a mixture of tetracycline isomer, citric acid and detergent (MTAD and ethylene diamine tetra-acetic acid (EDTA in removing the smear layer along with their effects on peritubular and intertubular dentinal structures by scanning electron microscopic (SEM examination. Materials and Methods: Thirty recently extracted maxillary and mandibular single-rooted human teeth were divided into 3 groups and prepared to an apical size of 30. In Group 1, 2, and 3, MTAD, EDTA, and distilled water were used, respectively, as a final rinse solution to remove the smear layer. The specimens were subjected to SEM evaluation for the presence or absence of the smear layer and degree of erosion using a scoring system. Results: The result showed that MTAD shows better smear layer removing ability and does not significantly change the structure of dentinal tubules. Conclusion: MTAD is an efficient solution for the removal of the smear layer, especially in the apical third of root canals, and does not significantly change the structure of the dentinal tubules.

Primum non nocere - The effects of sodium hypochlorite on dentin as used in endodontics.

Science.gov (United States)

Gu, Li-Sha; Huang, Xue-Qing; Griffin, Brandon; Bergeron, Brian R; Pashley, David H; Niu, Li-Na; Tay, Franklin R

2017-10-01

The medical literature is replete with the maxim 'primum non nocere', cautioning health care providers to avoid doing any harm to human subjects in their delivery of medical care. Sodium hypochlorite (NaOCl) is a well-established irrigant for root canal treatment because of its antimicrobial and organic tissue remnant dissolution capability. However, little is known about the deleterious effect of this strong oxidizing agent on the integrity of human mineralized dentin. Iatrogenically-induced loss of dentin integrity may precipitate post-treatment root fracture and has potential medico-legal complications. In the present work, transmission electron microscopy provided evidence for collagen destruction in the surface/subsurface of dentin treated with high NaOCl concentrations and long contact times. Size exclusion chromatography showed that the hypochlorite anion, because of its small size, penetrated the water compartments of apatite-encapsulated collagen fibrils, degraded the collagen molecules and produced a 25-35µm thick, non-uniform "ghost mineral layer" with enlarged, coalesced dentinal tubules and their lateral branches. Fourier transform-infrared spectroscopy identified increases in apatite/collagen ratio in NaOCl-treated dentin. The apatite-rich, collagen-sparse dentin matrix that remained after NaOCl treatment is more brittle, as shown by the reductions in flexural strength. Understanding the deleterious effects of NaOCl on mineralized dentin enables one to balance the risks and benefits in using high NaOCl concentrations for lengthy periods in root canal debridement. Delineating the mechanism responsible for such a phenomenon enables high molecular weight, polymeric antimicrobial and tissue dissolution irrigants to be designed that abides by the maxim of 'primum non nocere' in contemporary medical practices. The antimicrobial and tissue-dissolution capacities of NaOCl render it a well-accepted agent for root canal debridement. These highly desirable

Functional remineralization of carious dentin

Science.gov (United States)

Pugach, Megan Kardon

A primary goal of dental tissue engineering is the biological reconstruction of tooth substrate destroyed by caries or other diseases affecting tooth mineralization. Traditionally, dentists treat caries by using invasive techniques to remove the diseased dental tissue and restore the lesion, ideally preventing further progression of decay. Success in strategies associated with remineralization of enamel and root caries have contributed to the less invasive prospect of remineralization of dentinal carious lesions. The central hypothesis of this dissertation is that carious dentin lesions can be remineralized if the lesions contain residual mineral. Caries Detector (CD) stained zones (pink, light pink, transparent and normal) of arrested carious dentin lesions were characterized according to microstructure by atomic force microscopy (AFM) imaging, mineral content by digital transverse microradiography, and nanomechanical properties by AFM-based nanoindentation. CD-stained and unstained zones had significantly different microstructure, mineral content and nanomechanical properties. Furthermore, the most demineralized carious zone contained residual mineral. To obtain reproducible, standardized dentin caries lesions, we characterized the lesions from an artificial carious dentin lesion model using a 0.05M acetate demineralization buffer. The artificial caries-like lesions produced by the buffer had similar mineral content and nanomechanical properties in the stained and unstained zones as natural dentin lesions. Both natural and artificial lesions had significant correlations between mineral content and nanomechanical properties. Mineral crystallite size and shape was examined by small angle x-ray scattering. Both natural and artificial carious dentin had different mineral sizes than normal dentin. Collagen in natural and artificial carious dentin lesions was examined by trichrome stain, AFM high-resolution imaging, and UV resonance Raman spectroscopy, to determine if

Preexisting Dentinal Microcracks in Nonendodontically Treated Teeth: An Ex Vivo Micro-computed Tomographic Analysis.

Science.gov (United States)

PradeepKumar, Angambakkam Rajasekaran; Shemesh, Hagay; Chang, Jeffrey Wen-Wei; Bhowmik, Ahendita; Sibi, Swamy; Gopikrishna, Velayutham; Lakshmi-Narayanan, Lakshmikanthanbharathi; Kishen, Anil

2017-06-01

This study evaluated the prevalence, location, and pattern of preexisting dentinal microcracks in roots of extracted teeth without endodontic treatment in patients from 2 age groups using micro-computed tomographic imaging. Six hundred thirty-three nonendodontically treated teeth extracted using an atraumatic procedure because of reasons unrelated to this study were collected and divided based on the patient age. Teeth were scanned with micro-computed tomographic imaging (resolution of 26.7 μm) to examine the presence of preexisting dentinal microcracks in roots. The characteristic features of preexisting dentinal microcracks determined were location, extent, length, and coronoapical distribution. Chi-square bivariate analysis was performed to assess the association between various parameters. Forty-five of 633 nonendodontically treated teeth exhibited preexisting microcracks in roots with a prevalence of 7.1%. The prevalence of preexisting microcracks was found to be 8.3% in older patients (40-70 years) compared with 3.7% in younger patients (20-39 years) (P < .050). A significant association was found between the preexisting microcracks in mandibular teeth (10.3%) when compared with maxillary teeth (2.9%) (P < .001). All preexisting microcracks were located mesiodistally; 66% occurred in the cervical and middle thirds of root. Only 33% of the preexisting microcracks were complete in nature, showing canal involvement. Complete dentinal microcracks exhibited a mean length of 6.9 mm, whereas incomplete cracks had a mean length of 3.75 mm (P < .001). Preexisting dentinal microcracks in roots of nonendodontically treated teeth occurred more often in older patients (40-70 years) in the mesiodistal direction. They were predominantly found in the cervical and middle thirds of root and were more likely to be incomplete in nature. Copyright © 2017 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Regeneration of dental pulp/dentine complex with a three-dimensional and scaffold-free stem-cell sheet-derived pellet.

Science.gov (United States)

Na, Sijia; Zhang, Hao; Huang, Fang; Wang, Weiqi; Ding, Yin; Li, Dechao; Jin, Yan

2016-03-01

Dental pulp/dentine complex regeneration is indispensable to the construction of biotissue-engineered tooth roots and represents a promising approach to therapy for irreversible pulpitis. We used a tissue-engineering method based on odontogenic stem cells to design a three-dimensional (3D) and scaffold-free stem-cell sheet-derived pellet (CSDP) with the necessary physical and biological properties. Stem cells were isolated and identified and stem cells from root apical papilla (SCAPs)-based CSDPs were then fabricated and examined. Compact cell aggregates containing a high proportion of extracellular matrix (ECM) components were observed, and the CSDP culture time was prolonged. The expression of alkaline phosphatase (ALP), dentine sialoprotein (DSPP), bone sialoprotein (BSP) and runt-related gene 2 (RUNX2) mRNA was higher in CSDPs than in cell sheets (CSs), indicating that CSDPs have greater odonto/osteogenic potential. To further investigate this hypothesis, CSDPs and CSs were inserted into human treated dentine matrix fragments (hTDMFs) and transplanted into the subcutaneous space in the backs of immunodeficient mice, where they were cultured in vivo for 6 weeks. The root space with CSDPs was filled entirely with a dental pulp-like tissue with well-established vascularity, and a continuous layer of dentine-like tissue was deposited onto the existing dentine. A layer of odontoblast-like cells was found to express DSPP, ALP and BSP, and human mitochondria lined the surface of the newly formed dentine-like tissue. These results clearly indicate that SCAP-CSDPs with a mount of endogenous ECM have a strong capacity to form a heterotopic dental pulp/dentine complex in empty root canals; this method can be used in the fabrication of bioengineered dental roots and also provides an alternative treatment approach for pulp disease. Copyright © 2013 John Wiley & Sons, Ltd.

Pulsed Nd-YAG laser in endodontics

Science.gov (United States)

Ragot-Roy, Brigitte; Severin, Claude; Maquin, Michel

1994-12-01

The purpose of this study was to establish an operative method in endodontics. The effect of a pulsed Nd:YAG laser on root canal dentin has been examined with a scanning electron microscope. Our first experimentation was to observe the impacts carried out perpendicularly to root canal surface with a 200 micrometers fiber optic in the presence of dye. Secondarily, the optical fiber was used as an endodontic instrument with black dye. The irradiation was performed after root canal preparation (15/100 file or 40/100 file) or directly into the canal. Adverse effects are observed. The results show that laser irradiation on root canal dentin surfaces induces a nonhomogeneous modified dentin layer, melted and resolidified dentin closed partially dentinal tubules. The removal of debris is not efficient enough. The laser treatment seems to be indicated only for endodontic and periapical spaces sterilization after conventional root canal preparation.

Penetration of varnishes into demineralized root dentine in vitro

NARCIS (Netherlands)

Arends, J; Duschner, H; Ruben, JL

1997-01-01

In this paper the penetration of three different varnishes employed in caries prevention (Duraphat(R), Fluor Protector(R) and Cervitec(R)) into demineralized dentine is quantified using confocal laser scanning microscopy. The results show that the varnish penetration into lesions about 85 mu m in

Whole-field macro- and micro-deformation characteristic of unbound water-loss in dentin hard tissue.

Science.gov (United States)

Chen, Zhenning; Nadeau, Bobby; Yu, Kevin; Shao, Xinxing; He, Xiaoyuan; Goh, M Cynthia; Kishen, Anil

2018-04-06

High-resolution deformation measurements in a functionally graded hard tissue such as human dentin are essential to understand the unbound water-loss mediated changes and their role in its mechanical integrity. Yet a whole-field, 3-dimensional (3D) measurement and characterization of fully hydrated dentin in both macro- and micro-scales remain to be a challenge. This study was conducted in 2 stages. In stage-1, a stereo-digital image correlation approach was utilized to determine the water-loss and load-induced 3D deformations of teeth in a sagittal section over consecutively acquired frames, from a fully hydrated state to nonhydrated conditions for a period up to 2 hours. The macroscale analysis revealed concentrated residual deformations at the dentin-enamel-junction and the apical regions of root in the direction perpendicular to the dentinal tubules. Significant difference in the localized deformation characteristics was observed between the inner and outer aspects of the root dentin. During quasi-static loadings, further increase in the residual deformation was observed in the dentin. In stage-2, dentin microstructural variations induced by dynamic water-loss were assessed with environmental scanning electron microscopy and atomic force microscopy (AFM), showing that the dynamic water-loss induced distention of dentinal tubules with concave tubular edges, and concurrent contraction of intertubular dentin with convex profile. The findings from the current macro- and micro-scale analysis provided insight on the free-water-loss induced regional deformations and ultrastructural changes in human dentin. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

The effect of radiation therapy on the mechanical and morphological properties of the enamel and dentin of deciduous teeth—an in vitro study

International Nuclear Information System (INIS)

Siqueira Mellara, Talitha de; Palma-Dibb, Regina Guenka; Oliveira, Harley Francisco de; Garcia Paula-Silva, Francisco Wanderley; Nelson-Filho, Paulo; Silva, Raquel Assed Bezerra da; Silva, Léa Assed Bezerra da; Queiroz, Alexandra Mussolino de

2014-01-01

To evaluate the effects of radiation therapy on deciduous teeth. The enamel and dentin microhardness (n = 12) was evaluated at 3 depths, both before (control) and after each 10 Gy of irradiation and up to a dose of 60 Gy. The morphology was evaluated via scanning electron microscopy (SEM) (n = 8). The data were analyzed using a two-way analysis of variance (ANOVA) and Tukey’s test (α = 5%). The enamel microhardness, as a whole, increased (p < 0.05) after a dose of 60 Gy (211.4 KH), mostly in the superficial enamel. There was a significant difference between the values of nonirradiated dentin microhardness (28.9 KH) compared with dentin that was irradiated with doses of 10 Gy (23.8 KH), 20 Gy (25.6 KH), 30 Gy (24.8 KH), and 40 Gy (25.7 KH) (p < 0.05). There was no difference between nonirradiated dentin and dentin irradiated with 60 Gy (p > 0.05). The highest mean value of microhardness (29.9 KH) (p < 0.05) was found in the middle dentin. The groups that were irradiated with doses of 30 and 60 Gy exhibited greater surface changes in their enamel and dentin compared with the nonirradiated groups for all regions, exhibiting an amorphous surface upon increase of the irradiation doses. The enamel microhardness increased at a dose of 60 Gy, whereas the value of the dentin microhardness did not change. A progressive disruption of enamel and dentin morphology was found with the increased radiation dose

A fiber-optic setup for quantification of root surface demineralization

NARCIS (Netherlands)

vanderVeen, MH; tenBosch, JJ

A fiber-optic fluorescence observation (FOFO) technique has been developed for the quantification of demineralized root dentin, The method was tested on 40 specimens of in vitro demineralized parts of human root dentin, Fluorescein sodium salt was used as a penetrating dye, The fluorescein sodium

Evaluation of Dentin Defect Formation during Retreatment with Hand and Rotary Instruments: A Micro-CT Study.

Science.gov (United States)

Yilmaz, Ayca; Helvacioglu-Yigit, Dilek; Gur, Cansu; Ersev, Handan; Kiziltas Sendur, Gullu; Avcu, Egemen; Baydemir, Canan; Abbott, Paul Vincent

2017-01-01

The purpose of this study was to compare the incidence and longitudinal propagation of dentin defects after gutta-percha removal with hand and rotary instruments using microcomputed tomography. Twenty mandibular incisors were prepared using the balanced-force technique and scanned in a 19.9  μ m resolution. Following filling with the lateral compaction technique, gutta-percha was removed with ProTaper Universal Retreatment (PTUR) or hand instruments. After rescanning, a total of 24,120 cross-sectional images were analyzed. The numbers, types, and longitudinal length changes of defects were recorded. Defects were observed in 36.90% of the cross sections. A total of 73 defects were comprised of 87.67% craze lines, 2.73% partial cracks, and 9.58% fractures. No significant difference in terms of new defect formation was detected between the retreatment groups. The apical and middle portions of the roots had more dentin defects than the coronal portions. Defects in three roots of the PTUR instrument group increased in length. Under the conditions of this in vitro study, gutta-percha removal seemed to not increase the incidence of dentin defect formation, but the longitudinal defect propagation finding suggests possible cumulative dentinal damage due to additional endodontic procedures. Hand and rotary instrumentation techniques caused similar dentin defect formation during root canal retreatment.

New endodontic obturation systems and their interfacial bond strength with intraradicular dentine - ex vivo studies.

Science.gov (United States)

Pawińska, M; Kierklo, A; Tokajuk, G; Sidun, J

2011-01-01

To comparatively evaluate adhesive properties of selected root canal fillings through the measurement of the material-dentine interfacial bond strength. Fifty extracted single-rooted human teeth with one canal each were prepared using Hero instruments to size 30.04. Teeth were divided into four subgroups depending on the root canal filling material and the method of obturation: Resilon/Epiphany - a thermoplastic method (IA), Resilon/Epiphany - a matching single-point method (IB), gutta-percha/Roeko Seal Automix - a thermoplastic method (IIA) and gutta-percha/Roeko Seal Automix - a matching single-point method (IIB). The obturated roots were cut perpendicular to the long axis to create 1.7 mm thick slices. The bond strength was measured for each test slice with push -out testing machine. The highest push-out bond strength was registered in subgroup IB (3.98 ± 1.33 MPa). Significantly lower bond strength was observed in subgroups IA (0.50 ± 0.24 MPa), IIA (0.33 ± 0.18 MPa) and IIB (0.08 ± 0.03 MPa) (pmaterial-dentine interfacial bond strength values were observed between IA and IIA, IA and IIB, IIA and IIB subgroups (p > 0.05). The push-out bond strength of the material-dentine interface was dependent on the type of material used and the root canal filling technique. The R/E system exhibited better adhesion ability to intraradicular dentine than G/RSA. The highest bond strength was observed for Resilon/Epiphany introduced with the single-cone technique.

Analysis of peripheral thermal damage after laser irradiation of dentin using polarized light microscopy and synchrotron radiation infrared spectromicroscopy

Science.gov (United States)

Dela Rosa, Alfredo; Sarma, Anupama V.; Le, Charles Q.; Jones, Robert S.; Fried, Daniel

2004-05-01

It is necessary to minimize peripheral thermal damage during laser irradiation, since thermal damage to collagen and mineral compromises the bond strength to restorative materials in dentin and inhibits healing and osteointegration in bone. The overall objective of this study was to test the hypothesis that lasers resonant to the specific absorption of water, collagen, and hydroxyapatite with pulse durations less than the thermal relaxation times at each respective laser wavelength will efficiently remove dentin with minimal peripheral thermal damage. Precise incisions were produced in 3 x 3 mm2 blocks of human dentin using CO2 (9.6 μm), Er:YSGG (2.79 μm), and Nd:YAG (355 nm) lasers with and without a computer controlled water spray. Polarization-sensitive optical coherence tomography was used to obtain optical cross-sections of each incision to determine the rate and efficiency of ablation. The peripheral thermal damage zone around each incision was analyzed using polarized light microscopy (PLM) and Synchrotron-Radiation Fourier Transform Infrared Spectro-microscopy (SR-FTIR). Thermally induced chemical changes to both mineral and the collagen matrix was observed with SR-FTIR with a 10-μm spatial resolution and those changes were correlated with optical changes observed with PLM. Minimal (alveolar bone.

Influence of Laser Activated Irrigation with Erbium Lasers on Bond Strength of Inidividually Formed Fiber Reinforced Composite Posts to Root Canal Dentin

Directory of Open Access Journals (Sweden)

Ivana Miletić

2016-01-01

Full Text Available Objective: The aim of this in vitro study was to investigate the effect of laser activated irrigation (LAI using two erbium lasers on bond strength of individually formed fiber-reinforced composite (FRC posts to root canal dentin. Materials and methods: Twenty-seven single-rooted human teeth were endodontically treated and after post space preparation divided into three groups (n=9 per group, according to the pre-treatment of post space preparation: 1 Conventional syringe irrigation (CSI and saline; 2 Er.YAG photon-induced photoacoustic streaming (PIPS technique and saline; 3 Er,Cr:YSGG activated irrigation with RFT2 tip. Two specimens from each group were used for SEM analysis. The remaining specimens (n=7 per group received individually formed FRC post, everStick POST, luted with self-adhesive cement, G-CEM LinkAce. After cementation, the roots were perpendicularly sectioned into 1 mm thin sections and a push-out test was carried out (0.5 mm/min. The data were calculated as megapascals and were log transformed and statistically analysed using one-way ANOVA at the level of significance set at 5%. Results: In the control group, the smear layer was still present. In the Er:YAG group, the smear layer was removed. In the Er,Cr:YSGG group, the smear layer was partially removed. The Er,Cr:YSGG group achieved the highest bond strength values, followed by the control group and then the Er:YAG group, but no statistically significant difference was found in bond strength values in the tested group of post space pretreatment (p=0.564. Conclusions: LAI using two erbium lasers, with PIPS or RFT2 tip, did not affect the bond strength of individually formed FRC posts to root canal dentin.

Effect of polymerization mode of two adhesive systems on push-out bond strength of fiber post to different regions of root canal dentin

Directory of Open Access Journals (Sweden)

Shahram Farzin Ebrahimi

2014-01-01

Full Text Available Background: A few studies have investigated the effect of the activation mode of adhesive systems on bond strength of fiber posts to root canal dentin. This study investigated the push-out bond strengths of a glass fiber post to different root canal regions with the use of two adhesives with light- and dual-cure polymerization modes. Materials and Methods: In this in vitro study, 40 maxillary central incisors were decoronated at cement-enamel junction with 15 ± 1 mm root length. After root canal therapy and post space preparations, they were randomly divided into four groups. Post spaces were treated with four different adhesives: Excite, Excite Dual cure Single Component (DSC, self-etch adhesive (AdheSE, and AdheSE dual-cure. Then the fiber-reinforced composite (FRC post, Postec Plus, was cemented with dual-cure resin cement, Variolink II. The roots were cut into three 2-mm-thick slices. Push-out tests were performed with a universal testing machine at a crosshead speed of 0.5 mm/min. The mode of failures was determined under a stereomicroscope. Data were analyzed by three-way analysis of variance (ANOVA and Tukey test was conducted to compare post hoc with P < 0.05 as the level of significance. Results: The highest bond strength was obtained for AdheSE dual-cure (15.54 ± 6.90 MPa and the lowest was obtained for Excite light-cure (10.07 ± 7.45 MPa and only the bond strength between these two adhesives had significant difference (P = 0.02. Bond strength decreased from the coronal to the apical in all groups and this was significant in Excite (group 1 and AdheSE (group 3 (P < 0.001. In apical regions, bond strength of dual-cure adhesives was significantly higher than light-cure adhesives (P < 0.001. Conclusion: Push-out bond strength of fiber post to different regions of root canal dentin was affected by both adhesive systems and their polymerization modes.

An in vitro study of the Nd-YAG laser in the permeability of the cervical dentin

International Nuclear Information System (INIS)

Magalhaes, Manoelita Figueiredo de

2001-01-01

The purpose of this in vitro study was to verify the efficacy of the Nd:YAG pulse laser, with 1064 nm emission, in sealing the dentinal tubules for the treatment of dentin hypersensitivity, a very frequent complaint in the dental office. In spite of the existence of many articles over this subject, no fast, efficient and long lasting treatments for this problem were found yet. The obliteration of the opening of the dentinal tubules stops its inner fluid displacement and the consequent painful response (BRAENNSTROEM' S Hydrodynamics Theory). Twenty freshly and healthy extracted human teeth were used as samples, kept in saline solution. The cervical cement was removed with a 57FG Carbide bur in order to expose the dentin in an area of approximately 4 mm 2 , two of which were in the buccal aspect: Groups A and S, and one in the lingual: Group C (control). A thickness plier was used to measure, directly in each sample, the thickness of the remaining dentin that was standardized, and only the samples with dentinal thickness between 1 and 1,5 mm were selected. The irradiation parameters were: 30 mJ energy per pulse; O,21 W power (Group A) and 40 mJ; O,28 W (Group B); 7 Hz frequency in both groups, in two applications of 43 seconds each with a 10 seconds interval between them. Subsequently, 10 of the samples were submitted to SEM (Screening Electronic Microscopy) examination, where it was detected a melting of the superficial dentin and a sealing of the dentinal tubules opening, besides the recrystallization of the dentin. It was then concluded that the use of the Nd:YAG laser was shown to be a very effective measure in melting and sealing the dentinal tubules and can use in treating dentin hypersensitivity, with the right parameters. The other 10 samples were cleaved in the center of the irradiated area in order to investigate the laser penetration depth in the dentin (SEM), with an approximate variation of up to 5Jlm in the center of the samples irradiated with the

The effect of gamma-irradiation on the sucrose content in sweet potato roots and potato tubers

International Nuclear Information System (INIS)

Hayashi, T.; Kawashima, K.

1982-01-01

The sucrose content in both potato tubers and sweet potato roots was considerably increased by gamma-irradiation. The maximum increase was achieved by an irradiation dose of 3 to 4 kGy for potatoes and 0.8 to 2 kGy for sweet potatoes. Cooling treatment (15°C, 2 weeks) for sweet potato roots also enhanced the sucrose content (almost 2 times) but was not additive to the irradiation treatment; the maximum sucrose content in irradiated sweet potato roots was in the range of 7 to 12% irrespective of the cooling treatment, depending on the variety of sweet potatoes. Irradiation made the sucrose content in the roots 2 to 4 times higher

Evaluation of Dentin Defect Formation during Retreatment with Hand and Rotary Instruments: A Micro-CT Study

Directory of Open Access Journals (Sweden)

Ayca Yilmaz

2017-01-01

Full Text Available The purpose of this study was to compare the incidence and longitudinal propagation of dentin defects after gutta-percha removal with hand and rotary instruments using microcomputed tomography. Twenty mandibular incisors were prepared using the balanced-force technique and scanned in a 19.9 μm resolution. Following filling with the lateral compaction technique, gutta-percha was removed with ProTaper Universal Retreatment (PTUR or hand instruments. After rescanning, a total of 24,120 cross-sectional images were analyzed. The numbers, types, and longitudinal length changes of defects were recorded. Defects were observed in 36.90% of the cross sections. A total of 73 defects were comprised of 87.67% craze lines, 2.73% partial cracks, and 9.58% fractures. No significant difference in terms of new defect formation was detected between the retreatment groups. The apical and middle portions of the roots had more dentin defects than the coronal portions. Defects in three roots of the PTUR instrument group increased in length. Under the conditions of this in vitro study, gutta-percha removal seemed to not increase the incidence of dentin defect formation, but the longitudinal defect propagation finding suggests possible cumulative dentinal damage due to additional endodontic procedures. Hand and rotary instrumentation techniques caused similar dentin defect formation during root canal retreatment.

Comparative study of age estimation using dentinal translucency by digital and conventional methods

Science.gov (United States)

Bommannavar, Sushma; Kulkarni, Meena

2015-01-01

Introduction: Estimating age using the dentition plays a significant role in identification of the individual in forensic cases. Teeth are one of the most durable and strongest structures in the human body. The morphology and arrangement of teeth vary from person-to-person and is unique to an individual as are the fingerprints. Therefore, the use of dentition is the method of choice in the identification of the unknown. Root dentin translucency is considered to be one of the best parameters for dental age estimation. Traditionally, root dentin translucency was measured using calipers. Recently, the use of custom built software programs have been proposed for the same. Objectives: The present study describes a method to measure root dentin translucency on sectioned teeth using a custom built software program Adobe Photoshop 7.0 version (Adobe system Inc, Mountain View California). Materials and Methods: A total of 50 single rooted teeth were sectioned longitudinally to derive a 0.25 mm uniform thickness and the root dentin translucency was measured using digital and caliper methods and compared. The Gustafson's morphohistologic approach is used in this study. Results: Correlation coefficients of translucency measurements to age were statistically significant for both the methods (P < 0.125) and linear regression equations derived from both methods revealed better ability of the digital method to assess age. Conclusion: The custom built software program used in the present study is commercially available and widely used image editing software. Furthermore, this method is easy to use and less time consuming. The measurements obtained using this method are more precise and thus help in more accurate age estimation. Considering these benefits, the present study recommends the use of digital method to assess translucency for age estimation. PMID:25709325

The Effect of Canal Preparation with Four Different Rotary Systems on Formation of Dentinal Cracks: An In Vitro Evaluation.

Science.gov (United States)

Khoshbin, Elham; Donyavi, Zakiyeh; Abbasi Atibeh, Erfan; Roshanaei, Ghodratollah; Amani, Faranak

2018-01-01

Endodontic rotary systems may result in dentinal cracks. They may propagate to vertical root fracture that compromises the outcome of endodontic treatment. This study aimed to compare Neolix and Reciproc (single-file systems), Mtwo and ProTaper (conventional rotary systems) in terms of dentinal crack formation in root canal walls. This in vitro study was conducted on 110 extracted human single-rooted teeth. The teeth were randomly divided into four experimental groups ( n =25) for root canal preparation with Neolix, Reciproc, Mtwo and ProTaper systems and two control groups ( n =5). The first control group underwent root canal instrumentation with hand files while the second control group received no preparation and was only irrigated. After instrumentation, root canals were horizontally sectioned at 3, 6 and 9 mm from the apex and inspected under a stereomicroscope under 12× magnification for detection of cracks. The data were analyzed using Chi-square, GEE test and Bonferroni tests ( P ProTaper, Reciproc, Mtwo and Neolix caused cracks in 92%, 80%, 68% and 48% of samples. ProTaper caused significantly more cracks than Neolix and Mtwo ( P 0.05). All rotary systems cause dentinal cracks and it is significantly different in apical, middle and coronal third of the root. Neolix appears to be a suitable alternative to other rotary systems since use of this single-file system saves time and cost and minimizes trauma to dentinal walls.

Dentin dysplasia type I : Five cases within one family

NARCIS (Netherlands)

Kalk, WWI; Batenburg, RHK; Vissink, A

Five cases of dentin dysplasia type I within one family are described. Clinically and radiologically, such patients are characterized by a delayed eruption pattern, opacity of the incisional margins, hypermobility of the teeth, short and defective roots, and obliterated pulp chambers. A conservative

Comprehensive analyses of how tubule occlusion and advanced glycation end-products diminish strength of aged dentin

Science.gov (United States)

Shinno, Yuko; Ishimoto, Takuya; Saito, Mitsuru; Uemura, Reo; Arino, Masumi; Marumo, Keishi; Nakano, Takayoshi; Hayashi, Mikako

2016-01-01

In clinical dentistry, since fracture is a major cause of tooth loss, better understanding of mechanical properties of teeth structures is important. Dentin, the major hard tissue of teeth, has similar composition to bone. In this study, we investigated the mechanical properties of human dentin not only in terms of mineral density but also using structural and quality parameters as recently accepted in evaluating bone strength. Aged crown and root dentin (age ≥ 40) exhibited significantly lower flexural strength and toughness than young dentin (age mineral density; but showed significantly lower flexural strength than young dentin. Dentin with strong alignment of the c-axis in hydroxyapatite exhibited high fracture strength, possibly because the aligned apatite along the collagen fibrils may reinforce the intertubular dentin. Aged dentin, showing a high advanced glycation end-products (AGEs) level in its collagen, recorded low flexural strength. We first comprehensively identified significant factors, which affected the inferior mechanical properties of aged dentin. The low mechanical strength of aged dentin is caused by the high mineral density resulting from occlusion of dentinal tubules and accumulation of AGEs in dentin collagen.

A Miniature Swine Model for Stem Cell-Based De Novo Regeneration of Dental Pulp and Dentin-Like Tissue.

Science.gov (United States)

Zhu, Xiaofei; Liu, Jie; Yu, Zongdong; Chen, Chao-An; Aksel, Hacer; Azim, Adham A; Huang, George T-J

2018-02-01

The goal of this study was to establish mini-swine as a large animal model for stem cell-based pulp regeneration studies. Swine dental pulp stem cells (sDPSCs) were isolated from mini-swine and characterized in vitro. For in vivo studies, we first employed both ectopic and semi-orthotopic study models using severe combined immunodeficiency mice. One is hydroxyapatite-tricalcium phosphate (HA/TCP) model for pulp-dentin complex formation, and the other is tooth fragment model for complete pulp regeneration with new dentin depositing along the canal walls. We found that sDPSCs are similar to their human counterparts exhibiting mesenchymal stem cell characteristics with ability to form colony forming unit-fibroblastic and odontogenic differentiation potential. sDPSCs formed pulp-dentin complex in the HA/TCP model and showed pulp regeneration capacity in the tooth fragment model. We then tested orthotopic pulp regeneration on mini-swine including the use of multi-rooted teeth. Using autologous sDPSCs carried by hydrogel and transplanted into the mini-swine root canal space, we observed regeneration of vascularized pulp-like tissue with a layer of newly deposited dentin-like (rD) tissue or osteodentin along the canal walls. In some cases, dentin bridge-like structure was observed. Immunohistochemical analysis detected the expression of nestin, dentin sialophosphoprotein, dentin matrix protein 1, and bone sialoprotein in odontoblast-like cells lining against the produced rD. We also tested the use of allogeneic sDPSCs for the same procedures. Similar findings were observed in allogeneic transplantation. This study is the first to show an establishment of mini-swine as a suitable large animal model utilizing multi-rooted teeth for further cell-based pulp regeneration studies.

Thermal analysis of different application techniques on Nd:YAG laser after root canal preparation of single-rooted teeth

International Nuclear Information System (INIS)

Archilla, Jose Ricardo de F.

2001-01-01

The experiment objective is to analyze temperature variation, by means of three different application techniques of Nd:YAG laser in the root canals of singlerooted anterior teeth. Three root canals were instrumented, irrigated, X-rayed to measure the remaining dentin in the apical area and submitted to laser irradiation techniques used by Gutknecht, Matsumoto and a new technique with oscillatory movement. The used laser parameters were: pulse energy 250 mJ, frequency 5 Hz, pulse fluency 354 J/cm 2 , average potency 1,25 W, pulse width 300 μs, fiber core diameter 300 μs and interval of thermal relaxation of 20 s. After temperature evaluation and interpretation of the obtained data, it was concluded: 1) the oscillatory technique provided a better heat distribution during the laser application, when analyzing the graphs separately; 2) all the used techniques are within a pattern of safety, analyzing the average and highest temperatures of the apical area and the middle third, even so, disrespecting the last application day and the middle third of root 'C'.(author)

Scanning electron microscopic observations of fibrous structure of cemento-dentinal junction in healthy teeth.

Science.gov (United States)

Pratebha, B; Jaikumar, N D; Sudhakar, R

2014-01-01

The cemento-dentinal junction (CDJ) is a structural and biologic link between cementum and dentin present in the roots of teeth. Conflicting reports about the origin, structure and composition of this layer are present in literature. The width of this junctional tissue is reported to be about 2-4 μm with adhesion of cementum and dentin by proteoglycans and by collagen fiber intermingling. The objective of this study is to observe and report the fibrous architecture of the CDJ of healthy tooth roots. A total of 15 healthy teeth samples were collected, sectioned into halves, demineralized in 5% ethylenediaminetetraacetic acid, processed using NaOH maceration technique and observed under a scanning electron microscope. The CDJ appeared to be a fibril poor groove with a width of 2-4 µm. Few areas of collagen fiber intermingling could be appreciated. A detailed observation of these tissues has been presented.

Variations in Enzymatic Activities of Shoots and Roots as an Indicator for Irradiated Seeds

International Nuclear Information System (INIS)

Abdelbbaary, N.A.; Elagamay, M.R.

2005-01-01

Germinated seedlings from oil seeds (sesame and sunflower) and legumes (Trigonella, Haricot, broad bean and cow pea) were irradiated with gamma rays at doses of 0, 0.2, 0.4, 0.8 and 1 kGy and the data were collected from shoots and roots. Enzymatic activities appeared to be correlated with gamma irradiation dose. The enzymatic activities of irradiated seeds understudy were significantly higher than controls. The peroxidase activities were nearly similar in both roots and shoots, while acid phosphatase activities in roots were higher than in shoots. Also protein contents were higher in roots. The peroxidase and acid phosphatase specific activities in roots were similar. Shoots peroxidase enzymatic activity increased with increased gamma doses. The seedling under study showed two different levels of peroxidase activity, higher as sesame, Trigonella and Sunflower, and lower such as all other legumes understudy. Similar tendency have been also noticed in roots-enzymatic activity, positive correlation between gamma doses treatment and peroxidase enzymatic activity, again two groups higher activity cow pea, broad bean, bean and Trigonella lower such as sesame, such as sesame, sunflower and haircut

Effects of dentin on the antimicrobial properties of endodontic medicaments.

Science.gov (United States)

Haapasalo, Markus; Qian, Wei; Portenier, Isabelle; Waltimo, Tuomas

2007-08-01

Successful treatment of apical periodontitis is dependent on the elimination of the infective microflora from the necrotic root canal system. Antimicrobial irrigating solutions and other locally used disinfecting agents and medicaments have a key role in the eradication of the microbes. While most if not all presently used disinfecting agents rapidly kill even the resistant microbes when tested in vitro in a test tube, the effectiveness of the same agents is clearly weaker in the in vivo conditions. Recent studies have given valuable information about the interaction of endodontic disinfecting agents with dentin and other compounds present in the necrotic root canal. As a result of such interactions the antimicrobial effectiveness of several of our key disinfectants may be weakened, or even eliminated under certain circumstances. Different disinfectants show different sensitivity to the action by the various potential inactivators, such as dentin, serum proteins, hydroxyapatite, collagen derived from different sources, and microbial biomass. This review is a summary of our present knowledge of the mostly negative interactions between endodontic disinfecting agents and the various compounds present in the root canal environment.

Micro-Computed Tomography Analysis of the Root Canal Morphology of Palatal Roots of Maxillary First Molars.

Science.gov (United States)

Marceliano-Alves, Marília; Alves, Flávio Rodrigues Ferreira; Mendes, Daniel de Melo; Provenzano, José Claudio

2016-02-01

A thorough knowledge of root canal anatomy is critical for successful root canal treatments. This study evaluated the internal anatomy of the palatal roots of maxillary first molars with micro-computed tomography (microCT). The palatal roots of extracted maxillary first molars (n = 169) were scanned with microCT to determine several anatomic parameters, including main canal classification, lateral canal occurrence and location, degree of curvature, main foramen position, apical constriction presence, diameters 1 and 2 mm from the apex and 1 mm from the foramen, minor dentin thickness in those regions, canal volume, surface area, and convexity. All canals were classified as Vertucci type I. The cross sections were oval in 61% of the canals. Lateral canals were found in 25% of the samples. The main foramen did not coincide with the root apex in 95% of the cases. Only 8% of the canals were classified as straight. Apical constriction was identified in 38% of the roots. The minor and major canal diameters and minor dentin thickness were decreased near the apex. The minor dentin thickness 1 mm from the foramen was 0.82 mm. The palatal canals exhibited a volume of 6.91 mm(3) and surface area of 55.31 mm(2) and were rod-shaped. The root canals of the palatal roots were classified as type I. However, some factors need to be considered during the treatment of these roots, including the frequent ocurrence of moderate/severe curvatures, oval-shaped cross-sections, and lateral canals, noncoincidence of the apical foramen with the root apex, and absence of apical constriction in most cases. Copyright © 2016 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Effect of dentin dehydration and composite resin polymerization mode on bond strength of two self-etch adhesives

Directory of Open Access Journals (Sweden)

Pooran Samimi

2016-01-01

Full Text Available Background: Dual-cured composite resins are similar to self-cured composite resins in some of their clinical applications due to inadequate irradiation, lack of irradiation, or delayed irradiation. Therefore, incompatibility with self-etch adhesives (SEAs should be taken into account with their use. On the other, the extent of dentin dehydration has a great role in the quality of adhesion of these resin materials to dentin. The aim of this study was to investigate the effect of dentin dehydration and composite resin polymerization mode on bond strength of two SEAs. Materials and Methods: A total of 120 dentinal specimens were prepared from extracted intact third molars. Half of the samples were dehydrated in ethanol with increasing concentrations. Then Clearfil SE Bond (CSEB and Prompt L-Pop (PLP adhesives were applied in the two groups. Cylindrical composite resin specimens were cured using three polymerization modes: (1 Immediate light-curing, (2 delayed light-curing after 20 min, and (3 self-curing. Bond strength was measured using universal testing machine at a crosshead speed of 1 mm/min. Data were analyzed with two-way ANOVA and Duncan post hoc tests. Statistical significance was defined at P 0.05. PLP showed significant differences between subgroups with the lowest bond strength in hydrated dentin with delayed light-curing and self-cured mode of polymerization. Conclusion: Within the limitations of this study, a delay in composite resin light-curing or using chemically cured composite resin had a deleterious effect on dentin bond strength of single-step SEAs used in the study.

Temperature increase beneath etched dentin discs during composite polymerization.

Science.gov (United States)

Karaarslan, Emine Sirin; Secilmis, Asli; Bulbul, Mehmet; Yildirim, Cihan; Usumez, Aslihan

2011-01-01

The purpose of this in vitro study was to measure the temperature increase during the polymerization of a composite resin beneath acid-etched or laser-etched dentin discs. The irradiation of dentin with an Er:YAG laser may have a positive effect on the thermal conductivity of dentin. This technique has not been studied extensively. Forty dentin discs (5 mm in diameter and 0.5 or 1 mm in height) were prepared from extracted permanent third molars. These dentin discs were etched with 20% orthophosphoric acid or an Er:YAG laser, and were then placed on an apparatus developed to measure temperature increases. The composite resin was polymerized with a high-intensity quartz tungsten halogen (HQTH) or light-emitting diode unit (LED). The temperature increase was measured under the dentin disc with a J-type thermocouple wire that was connected to a data logger. Five measurements were made for each dentin disc, curing unit, and etching system combination. Differences between the initial and the highest temperature readings were taken, and the five calculated temperature changes were averaged to determine the value of the temperature increase. Statistical analysis was performed with a three-way ANOVA and Tukey HSD tests at a 0.05 level of significance. Further SEM examinations were performed. The temperature increase values varied significantly, depending on etching systems (p < 0.05), dentin thicknesses (p < 0.05), and curing units (p < 0.05). Temperature increases measured beneath laser-etched discs were significantly higher than those for acid-etched dentin discs (p < 0.05). The HQTH unit induced significantly higher temperature increases than the LED unit (p < 0.05). The LED unit induced the lowest temperature change (5.2°C) in the 1-mm, acid-etched dentin group. The HQTH unit induced the highest temperature change (10.4°C) for the 0.5-mm, laser-etched dentin group. The risk of heat-induced pulpal damage should be taken into consideration

Effect of different irrigation protocols on the radicular dentin interface and bond strength with a metacrylate-based endodontic sealer.

Science.gov (United States)

Gonçalves, Lisandro; Silva-Sousa, Yara Teresinha Correa; Raucci Neto, Walter; Teixeira, Cleonice Silveira; Sousa-Neto, Manoel Damião; Alfredo, Edson

2014-06-01

This study assessed the influence of different endodontic chemical substances on the adhesion of the Epiphany SE/Resilon system (with and without resinous solvent) to radicular dentin walls, using the push-out test and scanning electron microscopy (SEM). Forty-eight root canals of human canines were prepared biomechanically with ProTaper rotary files (crown-down technique) and the radicular dentin was treated with either 17% EDTA, 2% chlorhexidine gel (CHX) or 2.5% NaOCl (control). The root canals were filled with Resilon cones and Epiphany SE sealer with and without resinous solvent. Six groups of eight canals each had their roots sectioned transversally to obtain 1-mm thick slices. Data were subjected to statistical analysis by ANOVA and Tukey's tests. The specimens treated with 17% EDTA (1.59 ± 0.91) presented higher bond strength (P Treatment of root canal walls with 17% EDTA, and addition of a resinous solvent to Epiphany SE produced the highest adhesion to radicular dentin. © 2014 Wiley Periodicals, Inc.

Pulpal progenitors and dentin repair.

Science.gov (United States)

Harichane, Y; Hirata, A; Dimitrova-Nakov, S; Granja, I; Goldberg, A; Kellermann, O; Poliard, A

2011-07-01

Mesenchymal stem cells are present in the dental pulp. They have been shown to contribute to dentin-like tissue formation in vitro and to participate in bone repair after a mandibular lesion. However, their capacity to contribute efficiently to reparative dentin formation after pulp lesion has never been explored. After pulp exposure, we have identified proliferative cells within 3 zones. In the crown, zone I is near the cavity, and zone II corresponds to the isthmus between the mesial and central pulp. In the root, zone III, near the apex, at a distance from the inflammatory site, contains mitotic stromal cells which may represent a source of progenitor cells. Stem-cell-based strategies are promising treatments for tissue injury in dentistry. Our experiments focused on (1) location of stem cells induced to leave their quiescent state early after pulp injury and (2) implantation of pulp progenitors, a substitute for classic endodontic treatments, paving the way for pulp stem-cell-based therapies.

Effect of Er:YAG laser-activated irrigation solution on Enterococcus Faecalis biofilm in an ex-vivo root canal model.

Science.gov (United States)

Sahar-Helft, Sharonit; Stabholtz, Adam; Moshonov, Joshua; Gutkin, Vitaly; Redenski, Idan; Steinberg, Doron

2013-07-01

Abstract Objective: The purpose of this study was to evaluate mineral content and surface morphology of root canals coated with Enterococcus faecalis biofilm after treatment with several endodontic irrigation solutions, with and without Er:YAG laser-activated irrigation (LAI). LAI has been introduced as a powerful method for root canal irrigation resulting in smear-layer removal from the root canal wall. Distal and palatal roots from 60 freshly extracted human molars were used in this study. The coronal of each tooth was removed. Roots were split longitudinally and placed in an ultrasonic bath to remove the smear layer, creating conditions for the formation of E. faecalis biofilm. After incubation, the two halves were reassembled in impression material to simulate clinical conditions. Specimens were divided into two main groups: roots rinsed with irrigation solutions and roots subjected to laser irradiation combined with irrigation solutions. Solutions tested were 2% chlorhexidine and 17% ethylenediaminetetraacetic acid (EDTA) and saline. Surface morphology: 17% EDTA irrigant solution combined with Er:YAG laser showed the best results for removing bacteria from the root canal walls. Chemical analysis: all samples treated with combined laser irradiation and irrigation solution had low surface levels of Ca compared with samples treated with irrigation alone. The Ca/P ratio was highest in the laser-EDTA group. Overall, mineral changes caused by laser with irrigation solutions were minimal, and statistically nonsignificant. In vitro irrigation solutions, combined with Er:YAG laser irradiation, were effective in removing E. faecalis biofilm from root canal walls. Irrigation solutions without laser irradiation were less effective, leaving a layer of biofilm on the dentin surface.

Inhibition of Cariogenic Plaque Formation on Root Surface with Polydopamine-Induced-Polyethylene Glycol Coating

Directory of Open Access Journals (Sweden)

May Lei Mei

2016-05-01

Full Text Available Root caries prevention has been a challenge for clinicians due to its special anatomical location, which favors the accumulation of dental plaque. Researchers are looking for anti-biofouling material to inhibit bacterial growth on exposed root surfaces. This study aimed to develop polydopamine-induced-polyethylene glycol (PEG and to study its anti-biofouling effect against a multi-species cariogenic biofilm on the root dentine surface. Hydroxyapatite disks and human dentine blocks were divided into four groups for experiments. They received polydopamine-induced-PEG, PEG, polydopamine, or water application. Contact angle, quartz crystal microbalance, and Fourier transform infrared spectroscopy were used to study the wetting property, surface affinity, and an infrared spectrum; the results indicated that PEG was induced by polydopamine onto a hydroxyapatite disk. Salivary mucin absorption on hydroxyapatite disks with polydopamine-induced-PEG was confirmed using spectrophotometry. The growth of a multi-species cariogenic biofilm on dentine blocks with polydopamine-induced-PEG was assessed and monitored by colony-forming units, confocal laser scanning microscopy, and scanning electron microscopy. The results showed that dentine with polydopamine-induced-PEG had fewer bacteria than other groups. In conclusion, a novel polydopamine-induced-PEG coating was developed. Its anti-biofouling effect inhibited salivary mucin absorption and cariogenic biofilm formation on dentine surface and thus may be used for the prevention of root dentine caries.

Efficacy of 4 Irrigation Protocols in Killing Bacteria Colonized in Dentinal Tubules Examined by a Novel Confocal Laser Scanning Microscope Analysis.

Science.gov (United States)

Azim, Adham A; Aksel, Hacer; Zhuang, Tingting; Mashtare, Terry; Babu, Jegdish P; Huang, George T-J

2016-06-01

The aim of this study was to determine the efficiency of 4 irrigation systems in eliminating bacteria in root canals, particularly in dentinal tubules. Roots of human teeth were prepared to 25/04, autoclaved, and inoculated with Enterococcus faecalis for 3 weeks. Canals were then disinfected by (1) standard needle irrigation, (2) sonically agitating with EndoActivator, (3) XP Endo finisher, or (4) erbium:yttrium aluminum garnet laser (PIPS) (15 roots/group). The bacterial reduction in the canal was determined by MTT assays. For measuring live versus dead bacteria in the dentinal tubules (4 teeth/group), teeth were split open and stained with LIVE/DEAD BackLight. Coronal, middle, and apical thirds of the canal dentin were scanned by using a confocal laser scanning microscope (CLSM) to determine the ratio of dead/total bacteria in the dentinal tubules at various depths. All 4 irrigation protocols significantly eliminated bacteria in the canal, ranging from 89.6% to 98.2% reduction (P bacteria in the coronal, middle, and apical segments at 50-μm depth. On the other hand, PIPS had the greatest bacterial killing efficiency at the 150-μm depth in all 3 root segments. XP Endo appears to be more efficient than other 3 techniques in disinfecting the main canal space and up to 50 μm deep into the dentinal tubules. PIPS appears to be most effective in killing the bacteria deep in the dentinal tubules. Copyright © 2016 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

The influence of the Q-switched and free-running Er:YAG laser beam characteristics on the ablation of root canal dentine

International Nuclear Information System (INIS)

Papagiakoumou, Eirini; Papadopoulos, Dimitrios N.; Khabbaz, Marouan G.; Makropoulou, Mersini I.; Serafetinides, Alexander A.

2004-01-01

Laser based dental treatment is attractive to many researchers. Lasers in the 3 μm region, as the Er:YAG, are suitable especially for endodontic applications. In this study a pulsed free-running and Q-switched laser was used for the ablation experiments of root canal dentine. The laser beam was either directly focused on the dental tissue or delivered to it through an infrared fiber. For different spatial beam distributions, energies, number of pulses and both laser operations the quality characteristics (crater's shape formation, ablation efficiency and surface characteristics modification) were evaluated using scanning electron microscopy (SEM). The craters produced, generally, reflect the relevant beam profile. Inhomogeneous spatial beam profiles and short pulse duration result in cracks formation and lower tissue removal efficiency, while longer pulse durations cause hard dentine fusion. Any beam profile modification, due to laser characteristics variations and the specific delivering system properties, is directly reflected in the ablation crater shape and the tissue removal efficiency. Therefore, the laser parameters, as fluence, pulse repetition rate and number of pulses, have to be carefully adjusted in relation to the desirable result

Comparison of dentinal damage induced by different nickel-titanium rotary instruments during canal preparation: An in vitro study.

Science.gov (United States)

Garg, Shiwani; Mahajan, Pardeep; Thaman, Deepa; Monga, Prashant

2015-01-01

To compare dentinal damage caused by hand and rotary nickel-titanium instruments using ProTaper, K3 Endo, and Easy RaCe systems after root canal preparation. One hundred and fifty freshly extracted mandibular premolars were randomly divided into five experimental groups of 30 teeth each and biomechanical preparation was done: Group 1 with unprepared teeth; Group 2 were prepared with hand files; Group 3 with ProTaper rotary instruments; Group 4 with K3 rotary; Group 5 with Easy RaCe rotary instruments. Then, roots were cut horizontally at 3, 6, and 9 mm from apex and were viewed under stereomicroscope. The presence of dentinal defects was noted. Groups were analyzed with the Chi-square test. Significant difference was seen between groups. No defects were found in unprepared roots and those prepared with hand files. ProTaper, K3 rotary, and Easy RaCe preparations resulted in dentinal defects in 23.3%, 10%, and 16.7% of teeth, respectively. More defects were shown in coronal and middle sections, and no defect was seen in apical third. The present study revealed that use of rotary instruments could result in an increased chance for dentinal defects as compared to hand instrumentation.

Effects of self-adjusting file, Mtwo, and ProTaper on the root canal wall.

Science.gov (United States)

Hin, Ellemieke S; Wu, Min-Kai; Wesselink, Paul R; Shemesh, Hagay

2013-02-01

The purpose of this ex vivo study was to observe the incidence of cracks in root dentin after root canal preparation with hand files, self-adjusting file (SAF), ProTaper, and Mtwo. One hundred extracted mandibular premolars with single canals were randomly selected. Two angulated radiographs were taken for each tooth, and the width of the canal was measured at 9 mm from the apex. Five groups of 20 teeth each were comparable in canal width. The control group was left unprepared. Four experimental groups were instrumented with hand files, ProTaper, Mtwo, and SAF. Roots were then sectioned horizontally and observed under a microscope. The presence of dentinal cracks and their location were noted. The difference between the experimental groups was analyzed with a χ(2) test. No cracks were observed in the control group. In the experimental groups, ProTaper, Mtwo, and SAF caused cracks in 35%, 25%, and 10% of teeth, respectively. The hand-file group did not show any dentinal cracks (P ProTaper and Mtwo caused more cracks than hand files (P .05). Instrumentation of root canals with SAF, Mtwo, and ProTaper could cause damage to root canal dentin. SAF has a tendency to cause less dentinal cracks as compared with ProTaper or Mtwo. Copyright © 2013 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

The combination use of platelet-rich fibrin and treated dentin matrix for tooth root regeneration by cell homing.

Science.gov (United States)

Ji, Baohui; Sheng, Lei; Chen, Gang; Guo, Shujuan; Xie, Li; Yang, Bo; Guo, Weihua; Tian, Weidong

2015-01-01

Endogenous regeneration through cell homing provides an alternative approach for tissue regeneration, except cell transplantation, especially considering clinical translation. However, tooth root regeneration through cell homing remains a provocative approach in need of intensive study. Both platelet-rich fibrin (PRF) and treated dentin matrix (TDM) are warehouses of various growth factors, which can promote cell homing. We hypothesized that endogenous stem cells are able to sense biological cues from PRF membrane and TDM, and contribute to the regeneration of tooth root, including soft and hard periodontal tissues. Therefore, the biological effects of canine PRF and TDM on periodontal ligament stem cells (PDLSCs) and bone marrow mesenchymal stem cells (BMSCs) were evaluated respectively in vitro. Beagle dogs were used as orthotopic transplantation model. It was found that PRF significantly recruited and stimulated the proliferation of PDLSCs and BMSCs in vitro. Together, PRF and TDM induced cell differentiation by upregulating the mineralization-related gene expression of bone sialoprotein (BSP) and osteopotin (OPN) after 7 days coculture. In vivo, transplantation of autologous PRF and allogeneic TDM into fresh tooth extraction socket achieved successful root regeneration 3 months postsurgery, characterized by the regeneration of cementum and periodontal ligament (PDL)-like tissues with orientated fibers, indicative of functional restoration. The results suggest that tooth root connected to the alveolar bone by cementum-PDL complex can be regenerated through the implantation of PRF and TDM in a tooth socket microenvironment, probably by homing of BMSCs and PDLSCs. Furthermore, bioactive cues and inductive microenvironment are key factors for endogenous regeneration. This approach provides a tangible pathway toward clinical translation.

Anti-dentine Salivary SIgA in young adults with a history of dental trauma in deciduous teeth

Directory of Open Access Journals (Sweden)

Gabriela Fleury SEIXAS

2015-01-01

Full Text Available Anti-dentin autoantibodies are associated with inflammatory root resorption in permanent teeth and are modulated by dental trauma and orthodontic force. However, it is not known whether deciduous tooth trauma can stimulate the development of a humoral immune response against dentin. The aim of this study was to evaluate the levels of salivary SIgA reactivity against human dentin extract in young adults with a history of trauma in the primary dentition. A sample of 78 patients, aged 18 to 25, who had completed an early childhood (0 to 5 years old caries prevention program years earlier at the Universidade Estadual de LondrinaPediatric Clinic, underwent radiographic examination and salivary sampling. Anti-dentin SIgA levels were analyzed by immunoenzymatic assay and Western blotting. Although dental trauma to deciduous teeth had occurred in 34 (43.6% of the patients, no differences in SIgA levels were detected between individuals who had experienced trauma and those who had not (p > 0.05. Multivariate regression analysis showed no association between dental trauma and SIgA levels (p > 0.05. Patients with a history of deciduous trauma presented low levels of anti-dentin antibodies, associated with orthodontic root resorption (p

Influence of the Dentinal Wall on the pH of Sodium Hypochlorite during Root Canal Irrigation

NARCIS (Netherlands)

Macedo, Ricardo Gomes; Herrero, Noemi Pascual; Wesselink, Paul; Versluis, Michel; van der Sluis, Luc

Introduction: The purpose of this study was to evaluate the influence of dentin on the pH levels of different concentrations of sodium hypochlorite (NaOCl) solutions over time and to evaluate if preconditioning of dentin with 17% EDTA or agitation of the NaOCl solution influences these pH levels.

Assessment of root surfaces of apicected teeth: A scanning electron ...

African Journals Online (AJOL)

2014-05-15

May 15, 2014 ... exposed dentinal tubules, which may prevent the leakage ... stored in sterile distilled water at 37°C. Teeth with intact roots and mature apexes ..... 29. von Arx T, Kunz R, Schneider AC, Burgin W, Lussi A. Detection of dentinal.

A scanning electron microscopy study of diseased root surfaces conditioned with EDTA gel plus Cetavlon after scaling and root planing.

Science.gov (United States)

Martins Júnior, Walter; De Rossi, Andiara; Samih Georges Abi Rached, Ricardo; Rossi, Marcos Antonio

2011-01-01

In the present investigation, a scanning electron microscopy analysis was performed to evaluate the effects of the topical application of ethylenediaminetetraacetic acid (EDTA) gel associated with Cetavlon (EDTAC) in removing the smear layer and exposing collagen fibers following root surface instrumentation. Twenty-eight teeth from adult humans, single rooted and scheduled for extraction due to periodontal reasons, were selected. Each tooth was submitted to manual (scaling and root planing) instrumentation alone or combined with ultrasonic instruments, with or without etching using a 24% EDTAC gel. Following extraction, specimens were processed and examined under a scanning electron microscope. A comparative morphological semi-quantitative analysis was performed; the intensity of the smear layer and the decalcification of cementum and dentinal surfaces were graded in 12 sets using an arbitrary scale ranging from 1 (area covered by a smear layer) to 4 (no smear layer). Root debridement with hand instruments alone or combined with ultrasonic instruments resulted in a similar smear layer covering the root surfaces. The smear layer was successfully removed from the surfaces treated with EDTAC, which exhibited numerous exposed dentinal tubules and collagen fibers. This study supports the hypothesis that manual instrumentation alone or instrumentation combined with ultrasonic instrumentation is unable to remove the smear layer, whereas the subsequent topical application of EDTAC gel effectively removes the smear layer, uncovers dentinal openings and exposes collagen fibers.

Human dental enamel and dentin structural effects after Er:YAG laser irradiation.

Science.gov (United States)

Lima, Darlon Martíns; Tonetto, Mateus Rodrigues; de Mendonça, Adriano Augusto Melo; Elossais, André Afif; Saad, José Roberto Cury; de Andrade, Marcelo Ferrarezi; Pinto, Shelon Cristina Souza; Bandéca, Matheus Coelho

2014-05-01

Ideally projected to be applied on soft tissues, infrared lasers were improved by restorative dentistry to be used in hard dental tissues cavity preparations--namely enamel and dentin. This paper evidentiates the relevant aspects of infrared Erbium laser's action mechanism and its effects, and characterizes the different effects deriving from the laser's beams emission. The criteria for use and selection of optimal parameters for the correct application of laser systems and influence of supporting factors on the process, such as water amount and its presence in the ablation process, protection exerted by the plasma shielding and structural factors, which are indispensable in dental tissues cavity preparation related to restorative technique, are subordinated to optical modifications caused by the interaction of the energy dissipated by these laser light emission systems in the targeted tissue substrate. Differences in the action of infrared Erbium laser system in regard to the nature of the ablation process and variations on the morphological aspects observed in the superficial structure of the target tissue irradiated, may be correlated to the structural optical modifications of the substrate produced by an interaction of the energy propagated by laser systems.

In Vitro assessment of dentin erosion after immersion in acidic beverages: surface profile analysis and energy-dispersive X-ray fluorescence spectrometry study

OpenAIRE

Caneppele, Taciana Marco Ferraz; Jeronymo, Raffaela Di Iorio; Di Nicoló, Rebeca; Araújo, Maria Amélia Máximo de; Soares, Luís Eduardo Silva

2012-01-01

The aim of this study was to investigate the effects of some acidic drinks on dentin erosion, using methods of surface profile (SP) analysis and energy-dispersive X-ray fluorescence spectrometry (EDXRF). One hundred standardized dentin slabs obtained from bovine incisor roots were used. Dentin slabs measuring 5x5 mm were ground flat, polished and half of each specimen surface was protected with nail polish. For 60 min, the dentin surfaces were immersed in 50 mL of 5 different drinks (Gatorade...

Dentine tubule infection and endodontic therapy implications.

Science.gov (United States)

Oguntebi, B R

1994-07-01

A critical review of the literature suggests that the microenvironment of dentinal tubules appears to favour the selection of relatively few bacterial types irrespective of the aetiology of the infection process; coronal dental caries or pulpar necrosis. These bacteria may constitute an important reservoir from which root canal infection and reinfection may occur following pulp necrosis or during and after endodontic treatment. Previous studies of this microflora have utilized microbiological culture techniques which need to be supplemented by those that allow in situ demonstration as well as identification of the bacteria. Newer treatment strategies that are designed to eliminate this microflora must include agents that can penetrate the dentinal tubules and destroy these microorganisms, since they are located in an area beyond the host defence mechanisms where they cannot be reached by systemically administered antimicrobial agents.

Optical changes of dentin in the near-IR as a function of mineral content

Science.gov (United States)

Berg, Rhett A.; Simon, Jacob C.; Fried, Daniel; Darling, Cynthia L.

2017-02-01

The optical properties of human dentin can change markedly due to aging, friction from opposing teeth, and acute trauma, resulting in the formation of transparent or sclerotic dentin with increased mineral density. The objective of this study was to determine the optical attenuation coefficient of human dentin tissues with different mineral densities in the near-infrared (NIR) spectral regions from 1300-2200 nm using NIR transillumination and optical coherence tomography (OCT). N=50 dentin samples of varying opacities were obtained by sectioning whole extracted teeth into 150 μm transverse sections at the cemento-enamel junction or the apical root. Transillumination images were acquired with a NIR camera and attenuation measurements were acquired at various NIR wavelengths using a NIR sensitive photodiode. Samples were imaged with transverse microradiography (gold standard) in order to determine the mineral density of each sample.

The effect of dentin on the pulp tissue dissolution capacity of sodium hypochlorite and calcium hydroxide.

Science.gov (United States)

Slutzky-Goldberg, Iris; Hanut, Aiham; Matalon, Shlomo; Baev, Valery; Slutzky, Hagay

2013-08-01

Sodium hypochlorite (NaOCl) and calcium hydroxide (Ca[OH]2) have tissue dissolution capacity. The aim of this study was to evaluate the potential effect of dentin on their tissue dissolution capacity in a novel dentin model. Dentin models were prepared from 25 freshly extracted human molar teeth; the crowns were separated from the roots, and a rectangular inner shape was prepared. Pulp tissue samples adjusted to similar weights of 6.5 ± 0.2 mg were randomly divided into 6 groups: NaOCl groups in test tubes or dentin models for 1 hour, Ca(OH)2 groups in test tubes or dentin models for 1 week, and control groups saline in test tubes or dentin models for 1 week. The final weights after the experimental period were checked and compared with the initial weights. The differences were statistically analyzed. The tissue dissolution capacity of Ca(OH)2 was affected by the presence of dentin. Similarly, NaOCl lost its effect on the pulp tissue after incubation in dentin. Comparison between all test groups showed highly significant differences (P interactions between local endodontic medicaments, dentin, and pulp tissue. Copyright © 2013 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Effect of irradiation, pruning and removal of in vitro formed roots on ex vitro growth in micropropagated grape

International Nuclear Information System (INIS)

Charbaji, T.; Ayyoubi, Z.

2002-06-01

In vitro rootstock (Ru 140) and Helwani variety were cultured on DSD1 media, were irradiated at low doses of gamma irradiation before acclimatization. Ru 140 were exposed to 0-5 Gy, while Helwani was exposed to 0-7 Gy. Then, the plants were divided into three different groups: in the first group the plant roots were pruned, in the second the plant roots were completely removed and in the third group the plant roots were kept intact (control). The ex vitro plants were observed after 45 days of planting. Shoots groeth, leaf number and dry weight of Ru 140 were significantly higher than those of the control when roots were pruned and 5 Gy was applied. Those parameters were negatively affected by root removal. Gamma irradiation had a positive effect on the control comparing to unirradiated plants. Root pruning had positive effects on shoot growth, leaf number and dry weight of helwani veriety, while root removal had a contrary effect on this variety. Gamma irradiation positively affected shoot growth and dry weight of control comparing to unirradiated plants, similar effect was observed on leaf number of control and pruned plant of Helwani. (author)

Effect of Irradiation, Pruning and Removal of In Vitro Formed Roots on Ex Vitro Growth in Micropropagated Grape

International Nuclear Information System (INIS)

Charabaji, T.; Ayyoubi, Z.; Karajoly, I

2007-01-01

In vitro rootstock (Ru 140) and Helwani variety were cultured on DSD1 media, were irradiated at low doses of gamma irradiation before acclimatization. Ru 140 was exposed to 0-5 Gy, while Helwani was exposed to 0-7 Gy. Then, the plants were divided into three different procedures, 1)- the plant roots were pruned, 2)- the plant roots were completely removed, 3)- the plant roots were kept intact (control). The ex vitro plants were observed after 45 days of planting. Shoots growth, leaf number and dry weight of Ru 140 were significantly higher than those of the control when roots were pruned and 5 Gy was applied. Those parameters were negatively affected by root removal. Gamma irradiation had a positive effect on the control comparing to unirradiated plants. Root pruning had positive effects on shoot growth, leaf number and dry weight of Helwani variety, while root removal had a contrary effect on this variety. Gamma irradiation positively affected shoot growth and dry weight of control comparing to unirradiated plants, similar effect was observed on leaf number of control and pruned plant of Helwani.

In vitro comparative study of manual and mechanical rotary instrumentation of root canals using computed tomography.

Science.gov (United States)

Limongi, Orlando; de Albuquerque, Diana Santana; Baratto Filho, Flares; Vanni, José Roberto; de Oliveira, Elias P Motcy; Barletta, Fernando Branco

2007-01-01

This in vitro study compared, using computed tomography (CT), the amount of dentin removed from root canal walls by manual and mechanical rotary instrumentation techniques. Forty mandibular incisors with dental crown and a single canal were selected. The teeth were randomly assigned to two groups, according to the technique used for root canal preparation: Group I - manual instrumentation with stainless steel files; Group II - mechanical instrumentation with RaCe rotary nickel-titanium instruments. In each tooth, root dentin thickness of the buccal, lingual, mesial and distal surfaces in the apical, middle and cervical thirds of the canal was measured (in mm) using a multislice CT scanner (Siemens Emotion, Duo). Data were stored in the SPSS v. 11.5 and SigmaPlot 2001 v. 7.101 softwares. After crown opening, working length was determined, root canals were instrumented and new CT scans were taken for assessment of root dentin thickness. Pre- and post-instrumentation data were compared and analyzed statistically by ANOVA and Tukey's post-hoc test for significant differences (p=0.05). Based on the findings of this study, it may be concluded that regarding dentin removal from root canal walls during instrumentation, neither of the techniques can be considered more effective than the other.

Sensitivity of root-knot nematodes to gamma irradiation, salinity and plant growth regulator, cycocel

Energy Technology Data Exchange (ETDEWEB)

Sweelam, M E [Econ. Entomology Dept., Fac. Agric. Menoufia University Shebin El-Kom, (Egypt)

1995-10-01

The experiment was carried out at the experimental station of the faculty of agriculture, Menoufia Univ. To determine the sensitivity of root-knot nematode, Meloidogyne Javanica infecting tomato plants exposed to different doses of gamma irradiation 0,20,40,60,80 Gy, salinity levels 0. 1000, 2000, 4000 ppm and the plant growth regulator cycocel 0,200 ppm. Treated seeds were planted clay pots and salinity levels and cycocel concentrations were applied. Fresh weights and nematode populations were computed 3 months after application. Results indicated that 20 Gy, 1000 ppm salinity and cycocel gave the highest fresh weight of shoots and roots. The developmental stages and egg-laying females of nematode decreased by the increasing of irradiation dose and salinity levels. Root-knot galls decreased with 40 and 60 Gy, while significant increase was observed with 0 and 80 Gy, salinity levels decreased root galls. Cycocel decreased nematode population, egg-lying females and root-knot galls.

Sensitivity of root-knot nematodes to gamma irradiation, salinity and plant growth regulator, cycocel

International Nuclear Information System (INIS)

Sweelam, M.E.

1995-01-01

The experiment was carried out at the experimental station of the faculty of agriculture, Menoufia Univ. To determine the sensitivity of root-knot nematode, Meloidogyne Javanica infecting tomato plants exposed to different doses of gamma irradiation 0,20,40,60,80 Gy, salinity levels 0. 1000, 2000, 4000 ppm and the plant growth regulator cycocel 0,200 ppm. Treated seeds were planted clay pots and salinity levels and cycocel concentrations were applied. Fresh weights and nematode populations were computed 3 months after application. Results indicated that 20 Gy, 1000 ppm salinity and cycocel gave the highest fresh weight of shoots and roots. The developmental stages and egg-laying females of nematode decreased by the increasing of irradiation dose and salinity levels. Root-knot galls decreased with 40 and 60 Gy, while significant increase was observed with 0 and 80 Gy, salinity levels decreased root galls. Cycocel decreased nematode population, egg-lying females and root-knot galls

Impairment of the DNA synthesis in roots of γ-irradiated seedlings, and the restorative processes

International Nuclear Information System (INIS)

Golikova, O.P.; Mironyuk, T.J.

1976-01-01

Degradation of a prelabelled H 3 -DNA and post-irradiation incorporation of 2-C 14 -thymidine into root DNA of mung beans, peas, and horse beans, have been studied as a function of a radiation dose. A marked dose-dependent decrease in the activity of H 3 -DNA has been detected in γ-irradiated roots. As the radiation dose increases, the specific activity of 2-C 14 -DNA also increases in roots of beans and mung beans. A maximum increase is registered at a dose of 1500 rads. The effects observed are thought to be due to the restorative processes

Regulation of Reactionary Dentine Formation.

Science.gov (United States)

Neves, V C M; Sharpe, P T

2018-04-01

During the treatment of dental caries that has not penetrated the tooth pulp, maintenance of as much unaffected dentine as possible is a major goal during the physical removal of decayed mineral. Damage to dentine leads to release of fossilized factors (transforming growth factor-β [TGF-β] and bone morphogenic protein [BMP]) in the dentine that are believed to stimulate odontoblasts to secrete new "tertiary" dentine (reactionary dentine). This is formed on the pulpal surface of existing dentine and rethickens the dentine. We have previously shown that activation of Wnt/β-catenin signaling is pivotal for tooth repair in exposed pulp injury, and the pathway can be activated by small-molecule GSK-3 antagonists, resulting in enhanced reparative dentine formation. Here, we use a nonexposed pulp injury model to investigate the mechanisms of reactionary dentine formation in vivo, using small molecules to modulate the Wnt/β-catenin, TGF-β, and BMP pathways. We found that a local increase of Wnt activation at the injury site enhances reactionary dentine secretion. In addition, inhibition of TGF-β, BMP, or Wnt pathways does not impede reactionary dentine formation, although inhibition of TGF-β and/or BMP signaling does result in more disorganized, nontubular reactionary dentine. This suggests that Wnt/β-catenin signaling plays no major role in the formation of reactionary dentine, but in common with reparative dentine formation, exogenous elevation of Wnt/β-catenin signaling can enhance tertiary dentine formation. Release of latent TGF-β or BMPs from dentine is not required for the deposition of mineral to form reactionary dentine but does play a role in its organization.

Nd:YAG laser associated with metal salts solutions in the treatment of dentinal hypersensitivity

International Nuclear Information System (INIS)

Glauche, Carlos Eugenio Correia

2001-01-01

The objective of this study was to observe the ultrastructural changes caused by the radiation of Nd:YAG laser on the tooth tissue and determine qualitatively the presence of Sn ++ , Sr ++ and F - , inside the dentin, being it irradiated or not. Ten molar teeth recently extracted were cut into 2 mm discs. The samples were soaked in a EDTA solution at 17% for 2 minutes and divided into five groups. Group I: the samples were irradiated with Nd:YAG laser (1,5 W, 100 mJ, 15 Hz, 150 μs and 125 J/cm 2 ) and after that, a treatment with an SnF 2 aqueous solution at 10% for 30 minutes. Group II: the samples got laser irradiation with the same parameters and then a treatment with an SrCl 2 solution at 10% as a toothpaste (Sensodyne TM ) for 30 minutes. Group III: the samples just got a treatment with a SnF 2 aqueous solution at 10% for 30 minutes. Group IV: the samples just got a treatment with a SrCl 2 toothpaste (Sensodyne TM ) for 30 minutes. Group V: samples that just got laser irradiation in the parameters above mentioned. Then, all samples were prepared for scanning electronic microscopy (SEM) and the samples of groups I, II, III and IV for energy dispersive X-ray microanalysis (EDX). The ultrastructure aspect of the dentin showed the surface totally altered by the irradiation. Pits and whitish globules were found amidst an heterogenous and rough structure, due to the melting and resolidification of the dental structure. Craters were also observed. Carbonization areas were absent. Ions Sn ++ were found at a depth of 250 μm in the samples of group I (Nd:YAG + SnF 2 ), whereas in the samples of group III, Sn ++ were not found deeper than 100 μm. Sr ++ could be detected at least at 500 μm in the inner dentin in the samples of group II (Nd:YAG + SrCl 2 ). However, Sn ++ were not found at 50 μm in group IV samples. Ions F - were just found in the irradiated samples of group I. According to the study results we observed that through ultrastructural changes, caused by

Scanning electron microscopy evaluation of the interaction pattern between dentin and resin after cavity preparation using Er:YAG laser; Avaliacao, atraves de microscopia eletronica de varredura, do padrao de interacao dentina-resina em cavidades preparadas com laser de Er:YAG

Energy Technology Data Exchange (ETDEWEB)

Schein, Marcelo Thome

2001-07-01

The aim of this study was to describe the interaction pattern formed between dentin and resin on cavities prepared with an erbium laser (Er:YAG). The morphological aspect of the irradiated dentin after acid etching was also observed. Ten dentin disks were obtained from fresh extracted third molars. Each disk received two cavities, one prepared with a conventional high-speed drill, while the other cavity was obtained by the use of an Er:YAG laser (KaVo KEY Laser, KaVo Co.). The laser treatment was performed with 250 mJ/pulse, 4 Hz, non contact mode, focused beam, and a fine water mist was used. Five disks were prepared for morphological analysis of the acid etched dentin. The other five disks had their cavities restored with Single Bond (3M) followed by Z100 resin (3M). The specimens were observed under scanning electron microscopy after dentin-resin interface demineralization and deproteinization. It was observed that the morphological characteristics of the acid-etched irradiated dentin were not favorable to the diffusion of monomers through the collagen network. The dentin resin interfacial aspect of irradiated dentin, after acid etching, showed thin tags and scarce hybridization zones, which agreed with the morphology of the irradiated and acid-etched dentin substrate observed. (author)

Peritubular dentin lacks piezoelectricity.

Science.gov (United States)

Habelitz, S; Rodriguez, B J; Marshall, S J; Marshall, G W; Kalinin, S V; Gruverman, A

2007-09-01

Dentin is a mesenchymal tissue, and, as such, is based on a collagenous matrix that is reinforced by apatite mineral. Collagen fibrils show piezoelectricity, a phenomenon that is used by piezoresponse force microscopy (PFM) to obtain high-resolution images. We applied PFM to image human dentin with 10-nm resolution, and to test the hypothesis that zones of piezoactivity, indicating the presence of collagen fibrils, can be distinguished in dentin. Piezoelectricity was observed by PFM in the dentin intertubular matrix, while the peritubular dentin remained without response. High-resolution imaging of chemically treated intertubular dentin attributed the piezoelectric effect to individual collagen fibrils that differed in the signal strength, depending on the fibril orientation. This study supports the hypothesis that peritubular dentin is a non-collagenous tissue and is thus an exception among mineralized tissues that derive from the mesenchyme.

Influence of dental restorations and mastication loadings on dentine fatigue behaviour: Image-based modelling approach.

Science.gov (United States)

Vukicevic, Arso M; Zelic, Ksenija; Jovicic, Gordana; Djuric, Marija; Filipovic, Nenad

2015-05-01

The aim of this study was to use Finite Element Analysis (FEA) to estimate the influence of various mastication loads and different tooth treatments (composite restoration and endodontic treatment) on dentine fatigue. The analysis of fatigue behaviour of human dentine in intact and composite restored teeth with root-canal-treatment using FEA and fatigue theory was performed. Dentine fatigue behaviour was analysed in three virtual models: intact, composite-restored and endodontically-treated tooth. Volumetric change during the polymerization of composite was modelled by thermal expansion in a heat transfer analysis. Low and high shrinkage stresses were obtained by varying the linear shrinkage of composite. Mastication forces were applied occlusally with the load of 100, 150 and 200N. Assuming one million cycles, Fatigue Failure Index (FFI) was determined using Goodman's criterion while residual fatigue lifetime assessment was performed using Paris-power law. The analysis of the Goodman diagram gave both maximal allowed crack size and maximal number of cycles for the given stress ratio. The size of cracks was measured on virtual models. For the given conditions, fatigue-failure is not likely to happen neither in the intact tooth nor in treated teeth with low shrinkage stress. In the cases of high shrinkage stress, crack length was much larger than the maximal allowed crack and failure occurred with 150 and 200N loads. The maximal allowed crack size was slightly lower in the tooth with root canal treatment which induced somewhat higher FFI than in the case of tooth with only composite restoration. Main factors that lead to dentine fatigue are levels of occlusal load and polymerization stress. However, root canal treatment has small influence on dentine fatigue. The methodology proposed in this study provides a new insight into the fatigue behaviour of teeth after dental treatments. Furthermore, it estimates maximal allowed crack size and maximal number of cycles for a

Effect of irradiation, pruning and removal of in vitro formed roots on ex vitro growth in micro propagated grape

International Nuclear Information System (INIS)

Charbaji, T.; Ayyoubi, Z.

2003-01-01

In vitro rootstock (Ru 140) and Helwani variety were cultured on DSD1 media, were irradiated at low doses of gamma irradiation before acclimatization. Ru 140 were exposed to 0-5 Gy, while Helwani was exposed to 0-7 Gy. Then, the plants were divided into three different groups: in the first group the plant roots were pruned, in the second the plant roots were completely removed and in the third group the plant roots were kept intact (control). The ex vitro plants were observed after 45 days of planting. Shoots growth, leaf number and dry weight of Ru 140 were significantly higher than those of the control when roots were pruned and 5 Gy was applied. Those parameters were negatively affected by root removal. Gamma irradiation had a positive effect on the control comparing to unirradiated plants. Root pruning had positive effects on shoot growth, leaf number and dry weight of Helwani variety, while root removal had a contrary effect on this variety. Gamma irradiation positively affected shoot growth and dry weight of control comparing to unirradiated plants, similar effect was observed on leaf number of control and pruned plant of Helwani. (author)

Influence of the incidence angle on the morphology of enamel and dentin under Er:YAG laser irradiation; Estudo da influencia da angulacao do feixe laser na morfologia de esmalte e dentina irradiados com laser de Er:YAG

Energy Technology Data Exchange (ETDEWEB)

Junqueira Junior, Duilio Naves

2002-07-01

The purpose of this study is to make an in vitro evaluation, using scanning electron microscopy, of the influence of the laser beam irradiation angle on the enamel and dentin morphology. These tissues were both irradiated by Er:YAG Laser, with the same energy parameter. Twenty-four incisive bovine teeth were used, separated in eight groups, four of enamel, and four of dentin, with three specimens in each group. Each specimen was submitted to three laser applications, varying the incidence angle, between the laser and the tooth surface, at 90, 50 and 20 degrees. The applied frequency was 2 Hz, with 20 pulses in each application. The KaVo Key Laser 3 was employed, wavelength at 2940 nm, adjustable energy from 40 to 600 mJ and repetition rate from 1 to 25 Hz. The groups were distributed according to the energy parameter as follows - enamel: 250 mJ; 300 mJ; 350 mJ and 400 mJ; dentin: 200 mJ; 250 mJ; 300 mJ and 350 mJ. The results evidenced the Laser incidence angle importance; it is an essential parameter in the protocol of utilization and it should not be disregarded. The observations of this study allow to conclude that the Laser incidence angle has direct influence on the morphological aspect of the alterations produced in enamel and dentin. (author)

[Effects of Nd: YAG laser irradiation on the root surfaces and adhesion of Streptococcus mutans].

Science.gov (United States)

Yuanhong, Li; Zhongcheng, Li; Mengqi, Luo; Daonan, Shen; Shu, Zhang; Shu, Meng

2016-12-01

This study aimed to evaluate the effects of treatment with different powers of Nd: YAG laser irradiation on root surfaces and Streptococcus mutans (S. mutans) adhesion. Extracted teeth because of severe periodontal disease were divided into the following four groups: control group, laser group 1, laser group 2, and laser group 3. After scaling and root planning, laser group 1, laser group 2, and laser group 3 were separately treated with Nd: YAG laser irradiation (4/6/8 W, 60 s); however, the control group did not receive the treatment. Scanning electron microscopy (SEM) was used to determine the morphology. S. mutans were cultured with root slices from each group. Colony forming unit per mL (CFU·mL⁻¹) was used to count and compare the amounts of bacteria adhesion among groups. SEM was used to observe the difference of bacteria adhesion to root surfaces between control group (scaling) and laser group 2 (6 W, 60 s), thereby indicating the different bacteria adhesions because of different treatments. Morphology alterations indicated that root surfaces in control group contain obvious smear layer, debris, and biofilm; whereas the root surfaces in laser group contain more cracks with less smear layer and debris. The bacteria counting indicated that S. mutans adhesion to laser group was weaker than that of control group (P0.05) was observed. Morphology alterations also verified that S. mutans adhesion to laser group 2 (6 W, 60 s) was weaker than that of control group (scaling). This study demonstrated that Nd: YAG laser irradiation treatment after scaling can reduce smear layer, debris, and biofilm on the root surfaces as compared with conventional scaling. The laser treatment reduces the adhesion of S. mutans as well. However, Nd: YAG laser irradiation can cause cracks on the root surfaces. In this experiment, the optimum laser power of 6 W can thoroughly remove the smear layer and debris, as well as relatively improve the control of thermal damagee.

Effects of different peracetic acid formulations on post space radicular dentin.

Science.gov (United States)

Belizário, Lauriê Garcia; Kuga, Milton Carlos; Castro-Núñez, Gabriela Mariana; Escalante-Otárola, Wilfredo Gustavo; Só, Marcus Vinicius Reis; Pereira, Jefferson Ricardo

2018-01-05

The optimal irrigating solution with antimicrobial and dentin cleansing properties for post space preparation for fiber posts is unclear. Peracetic acid is one option but is available in various chemical formulations that require evaluation. The purpose of this in vitro study was to evaluate dentin surface cleanliness based on the presence of a smear layer and the number of open dentin tubules. It also investigates the chemical composition of residues after canal irrigation with a 1% peracetic acid solution (PA) at low or high concentration of hydrogen peroxide during the preparation of intracanal fiber posts. After filling the root canals of 40 mandibular incisors, a rotary instrument was used for intracanal preparation to place fiber posts. The teeth were divided into 4 groups (n=10) according to the post space irrigation protocol as follows: CG (control): distilled water; NA (NaOCl): 2.5% sodium hypochlorite; LH: PA with low concentration of hydrogen peroxide; and HH: PA with high concentrations of hydrogen peroxide. After irrigation, the teeth were sectioned, and the intracanal dentin surface was subjected to analysis using energy dispersive spectroscopy to evaluate chemical composition and to scanning electron microscopy (×500) to evaluate the presence of the smear layer. The number of open dentin tubules was measured by scanning electron microscopy analysis (×2000) using photo-editing software. ANOVA and the Tukey test (α=.05) were used to evaluate the data, except for the presence of a smear layer, for which the Kruskal-Wallis and Dunn tests were used (α=.05). The highest concentrations of oxygen in the dentin residues were detected in LH and HH (P.05). NA had a higher concentration of chlorine (P.05), except for HH, which also had a larger number of open dentin tubules than CG and NA (P<.05). PA 1% with a low concentration of hydrogen peroxide yielded a lower amount of smear layer and a larger number of open dentin tubules in the dentin of the post

Clinical and morphologic evaluation of Er:YAG laser action at the front of cervical dentinal hypersensitivity

International Nuclear Information System (INIS)

Rocha, Dalva Maria

2001-01-01

This work was achieved in vivo and in vitro to evaluate the efficiency of Er:YAG laser in the cervical dentinal hypersensitivity treatment (HSDC). The Clinical study was achieved in patients with HSDC. The treatment was realized in five sessions: the first for selection, the second for exams (clinic and X-Ray) and trying to remove the etiologic factors that could cause the HSDC. The third and fourth sessions were subjected to the radiation with that protocol: 60 mJ energy ,2 Hz frequency, 6 mm out of focus, under air cooling, 20 seconds each application which the same was repeated four times with one minute breaks, which scanning movements and without using anaesthetics. The fifth was evaluation. The patients were evaluated and registered in a subject scale of pain 0 to 3, in the beginning and end of each session of irradiation, and one month after the last session. The results showed that for the irradiated group occurs significant differences in the beginning of each session and between. For the control group did not occur significant differences in the beginning and after each session, but did show a difference between the sessions. As the control group as the irradiated group, had reduction of sensibility between the session. For the morphologic study nine teeth were selected, 7 molars and 2 pre-molars from operative dentistry discipline. Half of the surface was irradiated with Er:YAG laser, the same protocol used in vivo, and the other half was used as a control without receiving any laser irradiation. Subsequently, specimens were prepared for SEM examinations. The results showed that laser treated surfaces showed a reduction of dentine tubular diameter with partial or total closure of the dentine tubules. For the control group, it was observed bigger amounts smear layer and open dentine tubular. The results obtained indicated that the Er:YAG laser can contribute to the HSDC treatment. (author)

Rehardening of caries-like lesions in root surfaces by saliva substitutes.

Science.gov (United States)

Turssi, Cecilia P; Lima, Renata Q V; Faraoni-Romano, Juliana J; Serra, Mônica C

2006-12-01

This study sought to evaluate whether root dentine caries-like lesions could be remineralised by saliva substitutes. Root dentine slabs (3 x 3 x 2 mm) were cut from bovine incisors, ground flat, polished and pre-tested for Knoop microhardness (KHN) at five locations spaced 500 microm apart and 500 microm from the left edge of each sectioned piece. After 60 out of the 100 slabs had been selected based upon their KHN values, specimens were coated with wax except for their outer surface. Specimens were then cycled through a highly cariogenic challenge model to induce caries-like lesions, whose formation was confirmed by KHN measurements located 500 microm from the right edge of the specimen. According to a randomised complete block design, the experimental units (n = 15) were exposed to 1.5 ml of saliva substitutes, based on either mucin (MC) or carboxymethylcellulose (CM), to natural human saliva (HS) or to 100% relative humidity (RH) over 20 days. Remineralisation was verified by KHN measurements located 1000 microm apart from the right edge of the specimen. Analysis of variance indicated a significant (p < 0.0001) difference among the KHN values attained by the carious root dentine after exposure to the remineralising agents. Tukey's test ascertained that remineralisation was greatest with MC, intermediate with CM and least with HS, but rehardening did not reach the pre-caries lesion formation values. Saliva substitutes may provide partial remineralisation to preformed caries-like lesions in root dentine.

Influence of a glide path on the dentinal crack formation of ProTaper Next system

Directory of Open Access Journals (Sweden)

Sevinç Aktemur Türker

2015-11-01

Full Text Available Objectives The aim was to evaluate dentinal crack formation after root canal preparation with ProTaper Next system (PTN with and without a glide path. Materials and Methods Forty-five mesial roots of mandibular first molars were selected. Fifteen teeth were left unprepared and served as controls. The experimental groups consist of mesiobuccal and mesiolingual root canals of remaining 30 teeth, which were divided into 2 groups (n = 15: Group PG/PTN, glide path was created with ProGlider (PG and then canals were shaped with PTN system; Group PTN, glide path was not prepared and canals were shaped with PTN system only. All roots were sectioned perpendicular to the long axis at 1, 2, 3, 4, 6, and 8 mm from the apex, and the sections were observed under a stereomicroscope. The presence/absence of cracks was recorded. Data were analyzed with chi-square tests with Yates correction. Results There were no significant differences in crack formation between the PTN with and without glide path preparation. The incidence of cracks observed in PG/PTN and PTN groups was 17.8% and 28.9%, respectively. Conclusions The creation of a glide path with ProGlider before ProTaper Next rotary system did not influence dentinal crack formation in root canals.

Dentine microhardness after different methods for detection and removal of carious dentine tissue

Directory of Open Access Journals (Sweden)

Fernanda Brandão Mollica

2012-08-01

Full Text Available There are several methods for identifying carious dentinal tissue aiming to avoid removal of healthy dentinal tissue. OBJECTIVES: The purpose of this study was to test different methods for the detection of carious dentinal tissue regarding the amount of carious tissue removed and the remaining dentin microhardness after caries removal. MATERIAL AND METHODS: The dentin surfaces of 20 bovine teeth were exposed and half of the surface was protected with nail polish. Cariogenic challenge was performed by immersion in a demineralizing solution for 14 days. After transverse cross-section of the crown, the specimens were divided into four groups (n=10, according to the method used to identify and remove the carious tissue: "Papacárie", Caries-detector dye, DIAGNOdent and Tactile method. After caries removal, the cross-sectional surface was included in acrylic resin and polished. In a microhardness tester, the removed dentin thickness and the Vickers microhardness of the following regions were evaluated: remaining dentin after caries removal and superficial and deep healthy dentin. RESULTS: ANOVA and Tukey's test (α=0.05 were performed, except for DIAGNOdent, which did not detect the presence of caries. Results for removed dentin thickness were: "Papacárie" (424.7±105.0; a, Caries-detector dye (370.5±78.3; ab, Tactile method (322.8±51.5; bc. Results for the remaining dentin microhardness were: "Papacárie" (42.2±10.5; bc, Caries-detector dye (44.6±11.8; abc, Tactile method (24.3±9.0; d. CONCLUSIONS: DIAGNOdent did not detect the presence of carious tissue; Tactile method and "Papacárie" resulted in the least and the most dentinal thickness removal, respectively; Tactile method differed significantly from "Papacárie" and Caries-detector dye in terms of the remaining dentin microhardness, and Tactile method was the one which presented the lowest microhardness values.

Micro energy-dispersive x-ray fluorescence spectrometry study of dentin coating with nanobiomaterials

Science.gov (United States)

Soares, Luís. Eduardo Silva; Nahorny, Sídnei; Marciano, Fernanda Roberta; Zanin, Hudson; Lobo, Anderson de Oliveira

2015-06-01

New biomaterials such as multi-walled carbon nanotubes oxide/graphene oxide (MWCNTO/GO), nanohydroxyapatite (nHAp) and combination of them together or not to acidulated phosphate fluoride gel (F) have been tested as protective coating before root dentin erosion. Fourteen bovine teeth were cleaned, polished, divided into two parts (n=28) and assigned to seven groups: (Control) - without previous surface treatment; F treatment; nHAp; MWCNTO/GO; F+nHAp; F+MWCNTO/GO and F+MWCNTO/GO/nHAp composites. Each sample had two sites of pre-treatments: acid etched area and an area without treatment. After the biomaterials application, the samples were submitted to six cycles (demineralization: orange juice, 10 min; remineralization: artificial saliva, 1 h). Micro energy-dispersive X-ray fluorescence spectrometry (μ-EDXRF) mapping area analyses were performed after erosive cycling on both sites (n=84). μ-EDXRF mappings showed that artificial saliva and MWCNTO/GO/nHAp/F composite treatments produced lower dentin demineralization than in the other groups. Exposed dentin tubules allowed better interaction of nanobiomaterials than in smear layer covered dentin. Association of fluoride with other biomaterials had a positive influence on acid etched dentin. MWCNTO/GO/nHAp/F composite treatment resulted in levels of demineralization similar to the control group.

The effect of gamma irradiation and grounding on the microbial load of licorice roots (Glycyrrhiza glabra L.), and quality characteristics of its extract

International Nuclear Information System (INIS)

Al-Bachir, M.; Zeinou, R.

2002-12-01

Three type of ground root of licorice (fine particular 8.0 mm diameter) were divided into two groups, the first one was exposed to 0, 5, 10, 15 and 20 kGy. Whereas, the second group was exposed 0, 25, 50, 75, and 100 kGy of gamma radiation from a 60 Co source. Irradiated and non-irradiated samples were stored at room temperature. Microbial population, concentrations of glycyrrhizinic acid and some minerals of the extracts were evaluated after irradiation. The results showed that microbial count on fine particular of ground licorice roots were 10 6 g -1 , whereas, on coarse particular microbial counts was 10 5 g -1 . All size of licorice roots treated with gamma irradiation had significantly (p<0.05) lower counts than the untreated (control). The dose needed to reduce the microbial load to less than 10 bacteria per gram was 15 kGy for the fine particular of ground root, and 10 kGy for the coarse particular of ground root. The extract produced from coarse particular of ground roots had lower total dissolved solids, ash and mineral ions (Na, Ca, and K), ph, and Ec values compared with those produced from coarse particular of ground roots. Gamma irradiation decreased glycyrrhizinic acid concentrations in the extracts produced from ground licorice roots. High doses (25, 50, 75, and 100 kGy) of gamma irradiation decreased significantly the concentration of raw fiber, and glycyrrhizinic acid concentrations on ground licorice roots, and increased the dissolved solids and mineral ions (Na, Ca, and K) in extract of licorice root. Sensory evaluation indicated that there were no significant differences in colour, taste or flavour between extracts produced from irradiated with doses up to 25 kGy and non-irradiated roots. (author)

Comparative Analysis of Crack Propagation in Roots with Hand and Rotary Instrumentation of the Root Canal -An Ex-vivo Study.

Science.gov (United States)

Kumari, Manju Raj; Krishnaswamy, Manjunath Mysore

2016-07-01

Success of any endodontic treatment depends on strict adherence to 'endodontic triad'. Preparation of root canal system is recognized as being one of the most important stages in root canal treatment. At times, we inevitably end up damaging root dentin which becomes a Gateway for infections like perforation, zipping, dentinal cracks and minute intricate fractures or even vertical root fractures, thereby resulting in failure of treatment. Several factors may be responsible for the formation of dentinal cracks like high concentration of sodium hypochlorite, compaction methods and various canal shaping methods. To compare and evaluate the effects of root canal preparation techniques and instrumentation length on the development of apical root cracks. Seventy extracted premolars with straight roots were mounted on resin blocks with simulated periodontal ligaments, exposing 1-2 mm of the apex followed by sectioning of 1mm of root tip for better visualization under stereomicroscope. The teeth were divided into seven groups of 10 teeth each - a control group and six experimental groups. Subgroup A & B were instrumented with: Stainless Steel hand files (SS) up to Root Canal Length (RCL) & (RCL -1 mm) respectively; sub group C & D were instrumented using ProTaper Universal (PTU) up to RCL and (RCL -1mm) respectively; subgroup E & F were instrumented using ProTaper Next (PTN) up to RCL & (RCL -1 mm) respectively. Stereomicroscopic images of the instrumentation sequence were compared for each tooth. The data was analyzed statistically using descriptive analysis by 'Phi' and 'Cramers' test to find out statistical significance between the groups. The level of significance was set at phand file group showed most cracks followed by ProTaper Universal & ProTaper Next though statistically not significant. Samples instrumented up to 1mm short of working length (RCL-1mm) showed lesser number of cracks. All groups showed cracks formation, the stainless steel group being the highest

Challenges of stem cell-based pulp and dentin regeneration: a clinical perspective.

Science.gov (United States)

Huang, George T-J; Al-Habib, Mey; Gauthier, Philippe

2013-03-01

There are two types of approaches to regenerate tissues: cell-based and cell-free. The former approach is to introduce exogenous cells into the host to regenerate tissues, and the latter is to use materials other than cells in an attempt to regenerate tissues. There has been a significant advancement in stem cell-based pulp and dentin regeneration research in the past few years. Studies in small and large animals have demonstrated that pulp/dentin-like tissues can be regenerated partially or completely in the root canal space with apical openings of 0.7-3.0 mm using dental pulp stem cells, including stem cells from apical papilla (SCAP) and subpopulations of pulp stem cells. Bone marrow mesenchymal stem cells (BMMSCs) and adipose tissue-derived MSCs (ADMSCs) have also been shown to regenerate pulp-like tissue. In contrast, the cell-free approach has not produced convincing evidence on pulp regeneration. However, one crucial concept has not been considered nor defined in the field of pulp/dentin regeneration and that is the critical size defect of dentin and pulp. Without such consideration and definition, it is difficult to predict or anticipate the extent of cell-free pulp regeneration that would occur. By reasoning, cell-free therapy is unlikely to regenerate an organ/tissue after total loss. Similarly, after a total loss of pulp, it is unlikely to regenerate without using exogenously introduced cells. A cell homing approach may provide a limited amount of tissue regeneration. Although stem cell-based pulp/dentin regeneration has shown great promise, clinical trials are difficult to launch at present. This article will address several issues that challenge and hinder the clinical applications of pulp/dentin regeneration which need to be overcome before stem cell-based pulp/dentin regeneration can occur in the clinic.

Effect of Er,Cr:YSGG laser on the microtensile bond strength of two different adhesives to the sound and caries-affected dentin.

Science.gov (United States)

Ergücü, Z; Celik, E U; Unlü, N; Türkün, M; Ozer, F

2009-01-01

This study examined the effect of Er,Cr:YSGG laser irradiation on the microtensile bond strength (microTBS) of a three-step etch-and-rinse and a two-step self-etch adhesive to sound and caries-affected dentin. Sixteen freshly extracted human molars with occlusal dentin caries were used. The caries lesion was removed by one of the following methods: conventional treatment with burs or Er,Cr:YSGG laser (Waterlase MD, Biolase). The adhesive systems (AdheSE, Ivoclar Vivadent and Scotchbond Multi Purpose, 3M ESPE) were applied to the entire tooth surface according to the manufacturers' instructions. Resin composites were applied to the adhesive-treated dentin surfaces and light-cured. Each tooth was sectioned into multiple beams with the "non-trimming" version of the microtensile test. The specimens were subjected to microtensile forces (BISCO Microtensile Tester, BISCO). The data was analyzed by three-way ANOVA and independent t-tests (p=0.05). Er,Cr:YSGG laser irradiation exhibited similar microTBS values compared to that of conventional bur treatment, regardless of the adhesive system and type of treated dentin. The self-etch system revealed lower microTBS values, both with conventional and laser treatment techniques, compared to the etch-and-rinse adhesive in sound and caries-affected dentin (padhesive systems to sound and caries-affected dentin.

Comparison of the efficacy of ethylenediaminetetraacetic acid and tetracycline hydrochloride as root conditioning agents: An in vitro study

Directory of Open Access Journals (Sweden)

Tarun Nanda

2012-01-01

Full Text Available Objective: Root surfaces of periodontitis-affected teeth are hypermineralized and contaminated with cytotoxic and other biologically active substances. Various root conditioning agents have been recommended as an adjunct to mechanical root surface debridement to expose dentin collagen and cementum bound proteins. The aim of the present in vitro study was to compare the efficacy of ethylenediaminetetraacetic acid (EDTA and tetracycline hydrochloride (HCl as root conditioning agents on planed root surfaces. Materials and Methods: A total of 20 human maxillary anterior teeth indicated for extraction due to chronic periodontitis were collected and root planed. The teeth were sectioned and specimens were divided into two groups - Group I and II. Group I dentin specimens were treated with EDTA and Group II specimens were treated with tetracycline HCl solution at a concentration of 10% by active burnishing technique for 3 min. The root surface samples were then examined by scanning electron microscope. Results: The results of this study showed that EDTA and tetracycline HCl were equally effective in removing the smear layer. It was observed that the total and patent dentinal tubules were more in number in teeth treated with tetracycline when compared to EDTA group. However, EDTA was found to be much more effective as root conditioning agent because it enlarged the diameter of dentinal tubules more than that of tetracycline HCl. Conclusion: The results of in vitro study showed that both the agents are good root conditioning agents if applied in addition to periodontal therapy. However, further studies are required to establish the in vivo importance of EDTA and tetracycline HCL as root conditioners.

Diffusion ability of endotoxin through dentinal tubules Avaliação da difusão de endotoxinas através dos túbulos dentinários

Directory of Open Access Journals (Sweden)

Luciane Dias de Oliveira

2005-03-01

Full Text Available The aim of this study was to evaluate the ability of endotoxin to diffuse through dentinal tubules towards the cement and to observe the period of time needed for it to reach the external root surface. Thirty single-rooted human teeth had their crowns and apices removed in order to standardize the root length to 15 mm. Teeth were instrumented until #30 K-file and made externally impermeable with epoxy adhesive, leaving 10 mm of the exposed root (middle third. The specimens were placed in plastic vials and irradiated (60Co gamma-rays. Then, they were divided into 2 groups (n = 15: G1 Escherichia coli endotoxin was inoculated into the root canal of the specimens and 1 ml of pyrogen-free water was put in the tubes; G2 (control: pyrogen-free water was inoculated into the root canals and 1 ml of pyrogen-free water was put in each tube. After 30 min, 2 h, 6 h, 12 h, 24 h, 48 h, 72 h and 7 days, the water of the tubes was removed and replaced. The removed aliquot was tested for the presence of endotoxin. Considering that the endotoxin is a B-lymphocyte polyclonal activator, at each experimental period, B-lymphocyte culture was stimulated with a sample of water removed from each tube and antibody (IgM production was detected by ELISA technique. The results of IgM production were higher in groups of 24 h, 48 h, 72 h and 7 days in relation to the other studied groups, with statistically significant differences (ANOVA and Tukey's test p O objetivo desta pesquisa foi avaliar in vitro a capacidade e o tempo necessário para a endotoxina se difundir pelos túbulos dentinários em direção ao cemento. Foram utilizados 30 dentes humanos unirradiculados, que tiveram suas coroas e seus ápices seccionados, padronizando-se o tamanho em 15 mm. Os dentes foram instrumentados até a lima K30 e impermeabilizados externamente com adesivo epóxi, deixando-se 10 mm de raiz exposta (terço médio. Os espécimes foram acondicionados em tubos plásticos e submetidos �

Removal effects of the Nd:YAG laser and Carisolv on carious dentin.

Science.gov (United States)

Yamada, Y; Hossain, M; Kawanaka, T; Kinoshita, J; Matsumoto, K

2000-10-01

The purpose of this study was to investigate the removal effect of the Nd:YAG laser irradiation and Carisolv on carious dentin. Many previous studies have reported several simple and alternative techniques, such as lasers and chemicals, for caries removal. Carisolv was applied on the surface of 20 extracted human anterior and molar teeth for 1 min and then the Nd:YAG laser was irradiated with a continuous water spray for another 1 min. The energy densities were varied from 2 to 6W with a repetition rate of 20 pps. As caries removal progressed, the cavity was carefully assessed by DIAGNOdent. Each lesion was photographed before and after treatment, and the treated cavity was observed microscopically using a stereoscope and with scanning electron microscope (SEM). Thermal change at the time of laser irradiation was measured by thermovision. Our results revealed that application of Carisolv followed by Nd:YAG laser irradiation at 4-6W pulse energy effectively removed dentin caries. The total procedure was usually repeated once or twice for complete caries removal. From the SEM study, it was found that the cavity surface treated with the laser revealed various patterns of microirregularity, often accompanied by microfissure propagation. There was also no smear layer. It was revealed that Nd:YAG laser and Carisolv could provide an alternative technique for caries removal instead of the conventional mechanical drilling and cutting.

Shear Bond Strength of Composite to Nd-YAG Lased Dentin with and without Dye

Directory of Open Access Journals (Sweden)

H. Kermanshah

2004-06-01

Full Text Available Statement of Problem: The achievement of a good and durable dentin/composite resin bond is an important task in restorative dentistry. The application of acid conditioners and dentin bonding agents is an accepted method to enhance this bond strength. Pretreating of dentin surface by laser irradiation seems to be a supplemental way to obtain better results,since lased dentin is more roughened and has a widest surface area to interact with acidconditioner.Purpose: In this study, the effect of dentin surface pretreating by Nd-YAG laser on dentin/composite shear bond strength was examined. Moreover, the effect of Chinese ink as a surface energy absorber on this value was investigated.Methods and Materials: Thirty-nine freshly extracted human teeth without dentinal caries were collected and their occlusal dentins were exposed using a diamond disk. The collected samples were divided into three identical groups. The dentin surface of the first group was lased by an Nd-YAG pulsed laser (100 mJ, 20 Hz through a 320 mm fiber optic in a swiping movement. In the second group, 10% solution of Chinese ink was applied on the dentinal surface before lasing. The samples of the third group were not lased at all. Thedentinal surface prepared by 35% phosphoric acid and Scotchbond MP primer and adhesive. Then, composite resin was cured on dentinal surface. After incubation, in water at 37°C for 24 hours, the samples were tested by Digital Tritest ELE machine.Results: The values of bond strength were 20.83±3.96 MPa, 17.83±3.63 MPa and 19.38±4.88 MPa for the lased, unlased and dye-enhanced groups, respectively. The results were not significant by ANOVA test (a=0.05. Although in the Weiboul modulus, the lased group offered better bond strength.Conclusion: Further studies are required to determine whether chemical as well as physical alterations to the dentin surface are induced by laser etching, and whether these influence the performance of the range of dentin

Possible use of calcifying nanoparticles in immature root apex treatment

Directory of Open Access Journals (Sweden)

Mohammed S Alenazy

2014-01-01

Full Text Available Introduction: There are reports in the literature, which describe different techniques and materials in the challenging management of thin dentin walls and immature root apex. It has been suggested that calcifying nanoparticles (CNPs could be used in the management of these conditions. The Hypothesis: Compositionally modified CNPs made into a paste could become efficacious in managing thin dentin walls and immature root apex. Calcium and phosphate ions when mixed with CNPs could form a synthetic nanopaste that clinicians could use to manage thin dentin walls and to get a biological seal for immature root apex. Evaluation of the Hypothesis: CNPs can replicate and could facilitate the aggregations of calcium hydroxyapatite to produce a self-surrounding shell. These characteristics of CNPs could be used through their biomineralization process as initial nidus of calcification for further calcification progression to achieve total biological apical seal. If the hypothesis could be supported by biomineralization behavior of the paste (CNPs, Ca2 + , and PO4− , a new therapeutic agent would have been added to the armamentarium of endodontists. There is need for more in vivo and in vitro investigations of modified nanopaste to manage these conditions.

GAMMA IRRADIATION OF SUGAR BEET SEEDS INDUCED PLANT RESISTANCE TO ROOT-KNOT NEMATODE MELOIDOGYNE INCOGNITA

International Nuclear Information System (INIS)

ABD EL FATTAH, A.I.; KAMEL, H.A.; EL-NAGDI, W.M.A.

2008-01-01

The main objective of this study was to investigate the effect of irradiation of sugar beet seeds on the plant resistance to root-knot nematode Meloidogyne incognita infection in addition to some morphological parameters, biochemical components and root technological characters. Relative to control (non-irradiated seeds), the obtained data showed that, all doses except 10 Gy significantly increased root length of un inoculated plants and the most effective dose was 200 Gy. All doses significantly decreased root diameter except 50 and 100 Gy. The 10 and 400 Gy significantly reduced root fresh weight while 50, 100 and 200 Gy caused non-significant increase. All doses significantly increased root fresh weight/dry weight than control. There was non-significant effect on the morphological parameters of the plants germinated from gamma irradiated seeds and inoculated with Meloidogyne incognita. Total chlorophyll of seed irradiated and un inoculated plants were significantly reduced by all doses except 200 Gy. All doses of gamma radiation caused non-significant decrease in the total chlorophyll of the infected plants. In un inoculated plants, a significant reduction in the total phenol was occurred due to all doses of gamma radiation. In contrast, in inoculated plants, 10 and 25 Gy caused significant reduction in the total phenol while 50 and 400 Gy caused significant increase in the total phenol.Significant increase in sucrose % was observed due to 10 Gy in the un inoculated plants. The 400 Gy caused significant decrease while other doses caused non-significant decrease in the sucrose %. In the inoculated plants, 50, 100 and 400 Gy caused significant increase in sucrose %. All doses significantly increased total soluble salts percent (TSS %) of either inoculated or un inoculated plants. Purity % was increased by all doses in the inoculated plants.The number of galls and egg masses were reduced gradually by increasing gamma doses and 100 Gy caused the highest reduction 89

Effects of air polishing and an amino acid buffered hypochlorite solution to dentin surfaces and periodontal ligament cell survival, attachment, and spreading.

Science.gov (United States)

Schmidlin, Patrick R; Fujioka-Kobayashi, Masako; Mueller, Heinz-Dieter; Sculean, Anton; Lussi, Adrian; Miron, Richard J

2017-06-01

The aim of this study is to examine morphological changes of dentin surfaces following air polishing or amino acid buffered hypochlorite solution application and to assess their influence on periodontal ligament (PDL) cell survival, attachment, and spreading to dentin discs in vitro. Bovine dentin discs were treated with either (i) Classic, (ii) Plus, or (iii) Perio powder (EMS). Furthermore, Perisolv® a hypochlorite solution buffered with various amino acids was investigated. Untreated dentin discs served as controls. Morphological changes to dentin discs were assessed using scanning electron microscopy (SEM). Human PDL cells were seeded onto the respectively treated discs, and samples were then investigated for PDL cell survival, attachment, and spreading using a live/dead assay, adhesion assay, and SEM imaging, respectively. Both control and Perisolv®-rinsed dentin discs demonstrated smooth surfaces at low and high magnifications. The Classic powders demonstrated the thickest coating followed by the Powder Plus. The Perio powder demonstrated marked alterations of dentin discs by revealing the potential to open dentinal tubules even before rinsing. Seeding of PDL cells demonstrated an almost 100 % survival rate on all samples demonstrating very high biocompatibility for all materials. Significantly higher PDL cell numbers were observed on samples treated with the Perio powder and the Perisolv® solution (approximately 40 % more cells; p air polishing or application with Perisolv®. Future in vitro and animal testing is necessary to further characterize the beneficial effects of either system in a clinical setting. The use of air polishing or application with Perisolv amino acid buffered hypochlorite solution was effective in treating root surfaces and allowed for near 100 % PDL cell survival, attachment, and spreading onto all root surfaces.

Microtensile Bond Strength of Polyacid-modified Composite Resin to Irradiated Primary Molars.

Science.gov (United States)

Keles, Sultan; Yilmaz, Yucel; Sezen, Orhan

2018-02-01

This study evaluated the influence of various doses of radiotherapy on the microtensile bond strength (pTBS) of compomer resin to dentin and enamel in primary molars. Thirty-five intact primary molars were collected and divided into seven groups. Teeth were irradiated with doses from 10 to 60 Gy, except for the control group. Compomer restorations were performed, and enamel-compomer resin beams and dentin-compomer resin beams were tested at a crosshead speed of 1 mm/min. No statistically significant difference was found between the irradiated tooth enamel and the control group (F = 1.1468; p = 0.194). However, statistically significant differences were evident among the dentin groups (F = 11.050; p pTBS of compomer resin to primary tooth enamel, but appears to dose dependently decrease its bond strength to primary tooth dentin. Radiotherapy may affect the success rate of compomer fillings in primary teeth, especially in deeper cavities with exposed dentin.

Phototherapy up-regulates dentin matrix proteins expression and synthesis by stem cells from human-exfoliated deciduous teeth.

Science.gov (United States)

Turrioni, Ana Paula S; Basso, Fernanda G; Montoro, Liege A; Almeida, Leopoldina de Fátima D de; Costa, Carlos A de Souza; Hebling, Josimeri

2014-10-01

The aim of this study was to evaluate the effects of infrared LED (850nm) irradiation on dentin matrix proteins expression and synthesis by cultured stem cells from human exfoliated deciduous teeth (SHED). Near-exfoliation primary teeth were extracted (n=3), and SHED cultures were characterized by immunofluorescence using STRO-1, CD44, CD146, Nanog and OCT3/4 antibodies, before experimental protocol. The SHEDs were seeded (3×10(4) cells/cm(2)) with DMEM containing 10% FBS. After 24-h incubation, the culture medium was replaced by osteogenic differentiation medium, and the cells were irradiated with LED light at energy densities (EDs) of 0 (control), 2, or 4J/cm(2) (n=8). The irradiated SHEDs were then evaluated for alkaline phosphatase (ALP) activity, total protein (TP) production, and collagen synthesis (SIRCOL™ Assay), as well as ALP, collagen type I (Col I), dentin sialophosphoprotein (DSPP), and dentin matrix acidic phosphoprotein (DMP-1) gene expression (qPCR). Data were analyzed by Kruskal-Wallis and Mann-Whitney tests (α=0.05). Increased ALP activity and collagen synthesis, as well as gene expression of DSPP and ALP, were observed for both EDs compared with non-irradiated cells. The ED of 4J/cm(2) also increased gene expression of COL I and DMP-1. In conclusion, infrared LED irradiation was capable of biostimulating SHEDs by increasing the expression and synthesis of proteins related with mineralized tissue formation, with overall better results for the energy dose of 4J/cm(2). Phototherapy is an additional approach for the clinical application of LED in Restorative Dentistry. Infrared LED irradiation of the cavity's floor could biostimulate subjacent pulp cells, improving local tissue healing. Copyright © 2014 Elsevier Ltd. All rights reserved.

Evaluation of the root canal shaping ability of two rotary nickel-titanium systems.

Science.gov (United States)

Al-Manei, K K; Al-Hadlaq, S M S

2014-10-01

The aim was to investigate the canal shaping abilities of the twisted file (TF) and GT series X file (GTX) systems. Sixty mesial root canals of mandibular molars with curvatures of 15-50° were divided randomly into two groups of 30 canals each. The teeth were sectioned horizontally at 3, 6 and 9 mm from the apex. Root canals were prepared with TF and GTX files, respectively, and the shaping abilities of the systems were evaluated at three levels (coronal, middle and apical) based on the comparison of pre- and post-instrumentation photographs using AutoCAD software. Preparation time was also assessed. Data from the two groups were compared statistically using the Student's t-test. There was no significant difference between the rotary systems in terms of change in root canal cross-sectional area, root canal transportation, centring ability or minimum dentine thickness. Remaining dentine thickness at the coronal and middle levels was similar in the TF and GTX groups, but GTX instruments left significantly less dentine than TF instruments on the mesial aspects of root canals at the apical level. Root canal preparation with TF instruments required significantly less time than with GTX instruments. The TF and GTX NiTi rotary instruments showed similar shaping abilities, but root canal preparation was more rapid with the TF than with the GTX system. © 2014 International Endodontic Journal. Published by John Wiley & Sons Ltd.

Effects of irradiation with low-energy nitrogen ion injection on root tip cells of broad bean

International Nuclear Information System (INIS)

Huang Yaqin; Li Jinzhe; Huang Qunce

2012-01-01

In order to study the cytogenetic effects of low-energy nitrogen ion irradiation, broad bean seed embryo was irradiated by different doses of nitrogen ions. Micronucleus rate, mitotic index and chromosome aberration in root-tip cells were analyzed. The results showed that the injection of ions inhibited mitosis of root tip cells, interfered the normal process of mitosis, caused aberrations of chromosome structure, behavior and number. The frequency of micronucleus and chromosomal aberrations increased with the increasing radiation dosage, while mitotic index decreased. (authors)

Influence of refreshment/activation cycles and temperature rise on the reaction rate of sodium hypochlorite with bovine dentine during ultrasonic activated irrigation

NARCIS (Netherlands)

Macedo, R.G.; Verhaagen, B.; Wesselink, P.R.; Versluis, Michel; van der Sluis, L.W.M.

2014-01-01

Aim To evaluate the effect of multiple refreshment/activation cycles and temperature on the reaction rate of sodium hypochlorite (NaOCl) with bovine dentine during ultrasonic activated irrigation (UAI) under laboratory conditions. Methodology The root canal walls of 24 standardized root canals in

Comparative analysis of the effect of the GaAlAs laser irradiation in 780 nm and 660 nm in the hypersensitive dentin

International Nuclear Information System (INIS)

Yuan, Sun Chien

2003-01-01

This study was to evaluate and compare the effects of the low intensity in laser radiation among GaAlAs 780 nm and GaAlAs 660 nm. The main proposal is to verify if there is any difference of the effects or results in low intensity laser application treatment of hypersensitive dentin, keeping the same parameters, only differing in wavelength. The samples were distributed in two groups. Group A 90 cases, treated with GaAlAs 780 nm and group B irradiated with GaAlAs 660 nm with a total of 76 cases analyzed. The results of application with GaAlAs 660 nm and GaAlAs 780 nm do not differ statistically. Which means using any one of the irradiation gives the same results. However can be noted that the response of reduction of hypersensitivity is faster with the radiation of GaAlAs 780 nm, but the results after three applications is the same for both types of radiation. (author)

Improved reactive nanoparticles to treat dentin hypersensitivity.

Science.gov (United States)

Toledano-Osorio, Manuel; Osorio, Estrella; Aguilera, Fátima S; Luis Medina-Castillo, Antonio; Toledano, Manuel; Osorio, Raquel

2018-05-01

The aim of this study was to evaluate the effectiveness of different nanoparticles-based solutions for dentin permeability reduction and to determine the viscoelastic performance of cervical dentin after their application. Four experimental nanoparticle solutions based on zinc, calcium or doxycycline-loaded polymeric nanoparticles (NPs) were applied on citric acid etched dentin, to facilitate the occlusion and the reduction of the fluid flow at the dentinal tubules. After 24 h and 7 d of storage, cervical dentin was evaluated for fluid filtration. Field emission scanning electron microscopy, energy dispersive analysis, AFM and Nano-DMA analysis were also performed. Complex, storage, loss modulus and tan delta (δ) were assessed. Doxycycline-loaded NPs impaired tubule occlusion and fluid flow reduction trough dentin. Tubules were 100% occluded in dentin treated with calcium-loaded NPs or zinc-loaded NPs, analyzed at 7 d. Dentin treated with both zinc-NPs and calcium-NPs attained the highest reduction of dentinal fluid flow. Moreover, when treating dentin with zinc-NPs, complex modulus values attained at intertubular and peritubular dentin were higher than those obtained after applying calcium-NPs. Zinc-NPs are then supposed to fasten active dentin remodeling, with increased maturity and high mechanical properties. Zinc-based nanoparticles are then proposed for effective dentin remineralization and tubular occlusion. Further research to finally prove for clinical benefits in patients with dentin hypersensitivity using Zn-doped nanoparticles is encouraged. Erosion from acids provokes dentin hypersensitivity (DH) which presents with intense pain of short duration. Open dentinal tubules and demineralization favor DH. Nanogels based on Ca-nanoparticles and Zn-nanoparticles produced an efficient reduction of fluid flow. Dentinal tubules were filled by precipitation of induced calcium-phosphate deposits. When treating dentin with Zn-nanoparticles, complex modulus

The in vitro antibacterial effect of iodine-potassium iodide and calcium hydroxide in infected dentinal tubules at different time intervals.

Science.gov (United States)

Lin, Shaul; Kfir, Anda; Laviv, Amir; Sela, Galit; Fuss, Zvi

2009-03-01

The aim of this study was to evaluate the antibacterial effect of iodine-potassium iodide (IKI) and calcium hydroxide (CH) on dentinal tubules infected with Enterococcus faecalis (E. faecalis) at different time intervals. Hollow cylinders of bovine root dentin (n=45) were infected and divided into three equal groups filled with either IKI or CH and a positive control. After placing each medicament in the infected cylinders for time periods of 10 minutes, 48 hours and 7 days, microbiological samples were analyzed. At the end of each period, four 100 microm thick inner dentin layers (400 microm thick from each specimen) were removed using dental burs of increasing diameters. Dentin powder was cultured on agar plates to quantitatively assess their infection, expressed in colony forming units (cfu). In all layers of the positive control group, heavy bacterial infection was observed. After 10 minutes, IKI reduced the amount of viable bacteria more efficiently than CH, whereas at later time intervals CH showed the best results. For short periods of exposure, IKI has a more efficient antibacterial effect in the dentinal tubules than CH but CH performs better after longer durations of exposure. This research indicates the use of IKI is a better choice for disinfecting the root canal than CH if only a short duration of exposure is used because of its more efficient antibacterial effect. However, if a longer exposure time is used, then CH is a better choice because of its better disinfecting effect over time.

An in vitro study of the Nd-YAG laser in the permeability of the cervical dentin; Estudo in vitro do uso do laser Nd-YAG na permeabilidade dentinaria cervical

Energy Technology Data Exchange (ETDEWEB)

Magalhaes, Manoelita Figueiredo de

2001-07-01

The purpose of this in vitro study was to verify the efficacy of the Nd:YAG pulse laser, with 1064 nm emission, in sealing the dentinal tubules for the treatment of dentin hypersensitivity, a very frequent complaint in the dental office. In spite of the existence of many articles over this subject, no fast, efficient and long lasting treatments for this problem were found yet. The obliteration of the opening of the dentinal tubules stops its inner fluid displacement and the consequent painful response (BRAENNSTROEM' S Hydrodynamics Theory). Twenty freshly and healthy extracted human teeth were used as samples, kept in saline solution. The cervical cement was removed with a 57FG Carbide bur in order to expose the dentin in an area of approximately 4 mm{sup 2}, two of which were in the buccal aspect: Groups A and S, and one in the lingual: Group C (control). A thickness plier was used to measure, directly in each sample, the thickness of the remaining dentin that was standardized, and only the samples with dentinal thickness between 1 and 1,5 mm were selected. The irradiation parameters were: 30 mJ energy per pulse; O,21 W power (Group A) and 40 mJ; O,28 W (Group B); 7 Hz frequency in both groups, in two applications of 43 seconds each with a 10 seconds interval between them. Subsequently, 10 of the samples were submitted to SEM (Screening Electronic Microscopy) examination, where it was detected a melting of the superficial dentin and a sealing of the dentinal tubules opening, besides the recrystallization of the dentin. It was then concluded that the use of the Nd:YAG laser was shown to be a very effective measure in melting and sealing the dentinal tubules and can use in treating dentin hypersensitivity, with the right parameters. The other 10 samples were cleaved in the center of the irradiated area in order to investigate the laser penetration depth in the dentin (SEM), with an approximate variation of up to 5Jlm in the center of the samples irradiated with

An in vitro study of the Nd-YAG laser in the permeability of the cervical dentin; Estudo in vitro do uso do laser Nd-YAG na permeabilidade dentinaria cervical

Energy Technology Data Exchange (ETDEWEB)

Magalhaes, Manoelita Figueiredo de

2001-07-01

The purpose of this in vitro study was to verify the efficacy of the Nd:YAG pulse laser, with 1064 nm emission, in sealing the dentinal tubules for the treatment of dentin hypersensitivity, a very frequent complaint in the dental office. In spite of the existence of many articles over this subject, no fast, efficient and long lasting treatments for this problem were found yet. The obliteration of the opening of the dentinal tubules stops its inner fluid displacement and the consequent painful response (BRAENNSTROEM' S Hydrodynamics Theory). Twenty freshly and healthy extracted human teeth were used as samples, kept in saline solution. The cervical cement was removed with a 57FG Carbide bur in order to expose the dentin in an area of approximately 4 mm{sup 2}, two of which were in the buccal aspect: Groups A and S, and one in the lingual: Group C (control). A thickness plier was used to measure, directly in each sample, the thickness of the remaining dentin that was standardized, and only the samples with dentinal thickness between 1 and 1,5 mm were selected. The irradiation parameters were: 30 mJ energy per pulse; O,21 W power (Group A) and 40 mJ; O,28 W (Group B); 7 Hz frequency in both groups, in two applications of 43 seconds each with a 10 seconds interval between them. Subsequently, 10 of the samples were submitted to SEM (Screening Electronic Microscopy) examination, where it was detected a melting of the superficial dentin and a sealing of the dentinal tubules opening, besides the recrystallization of the dentin. It was then concluded that the use of the Nd:YAG laser was shown to be a very effective measure in melting and sealing the dentinal tubules and can use in treating dentin hypersensitivity, with the right parameters. The other 10 samples were cleaved in the center of the irradiated area in order to investigate the laser penetration depth in the dentin (SEM), with an approximate variation of up to 5Jlm in the center of the samples irradiated with the

Effect of desensitizing toothpastes on dentin

Directory of Open Access Journals (Sweden)

Shelon Cristina Souza Pinto

2012-10-01

Full Text Available The objective of this study was to analyze the effects of toothbrushing with desensitizing toothpastes on dentin permeability and dentinal tubule occlusion. Fifty rats provided two hundred incisor teeth divided into five groups: DW, brushed with distilled water (control; FT, brushed with fluoride toothpaste; SCT, brushed with strontium chloride toothpaste; PCT, brushed with potassium citrate toothpaste; and PNT, brushed with potassium nitrate toothpaste. Cavities were prepared to expose the dentinal tubules, and the incisor teeth were brushed using the experimental agents. After each treatment, Evans blue dye solution was applied to the teeth. Dentin permeability was analyzed using scanning electron microscopy and energy-dispersive X-rays (EDX. There were significant differences (p < 0.0001, ANOVA among the groups regarding dentin permeability, number of dentinal tubules, diameter of dentinal tubules, and opened tubular area. In the SCT, PCT and PNT groups, opened and partially occluded tubules, deposits, and a few smear layers were observed. In the DW and FT groups, most of the dentinal tubules were open, with no deposits or smear layers on the dentin. EDX revealed peaks of calcium and phosphorus in all of the groups, as well as traces of strontium in the SCT group and of potassium in the PCT and PNT groups. Desensitizing toothpaste decreased dentin permeability, although it produced only partial dentin tubule occlusion.

Effect of traditional methods and gamma irradiation on microbial load, quality and sensory characteristics of Licorice Roots Powder (Glycyrrhiza globra L.)

International Nuclear Information System (INIS)

Al-Bachir, M.; Al-Adawi, M.

2013-04-01

To determine the effect of gamma irradiation and heat treatment on microbial load of licorice root powder, extract rate from root powder, and the physical, chemical and sensory characteristics of its extract. Powder of licorice roots were exposed to heat treatments (hot air-dried and steam), and to 10 kGy of gamma irradiation. Microbial load on powder, and organic dissolved solids, total carbohydrates, reduced carbohydrates, Glycyrrhezinic, ash, mineral ions (Ca++ and K+, Na, Mg), pH and EC values, color, and sensory properties of the extracted were evaluated after 0, 6, and 12 months of storage. Results indicated that total microbial count of licorice roots powder (control sample) were relatively high, and included coliform, E. coli, and Klabsala spp. The results indicated that 10 kGy of gamma irradiation reduced the total count by 4 logs. While, heat treatment (hot air-dried, and steamed) reduced the total count by 1 and 2 logs respectively. No effect was observed in physical, and chemical characteristics in the extract of licorice roots due to irradiation. While, there were an effect of heat treatment on most of measured physical, and chemical characteristics of the extract of licorice roots. However, Sensory evaluation indicated that no significant differences were found between solution produced from irradiated, heat treated, and control samples in color, flavor, texture, or taste (author).

PDGFRβ+/c-kit+ pulp cells are odontoblastic progenitors capable of producing dentin-like structure in vitro and in vivo.

Science.gov (United States)

Cai, Shiwei; Zhang, Wenjian; Chen, Wei

2016-10-28

Successful pulp regeneration depends on identification of pulp stem cells capable of differentiation under odontoblastic lineage and producing pulp-dentinal like structure. Recent studies demonstrate that platelet-derived growth factor (PDGF) plays an important role in damage repair and tissue regeneration. The aim of this study was to identify a subpopulation of dental pulp cells responsive to PDGF and with dentin regeneration potential. Pulp tissues were isolated from 12 freshly extracted human impacted third molars. Pulp cells were sorted by their expression of PDGFRβ and stem cell marker genes via flow cytometry. For the selected cells, proliferation was analyzed by a colorimetric cell proliferation assay, differentiation was assessed by real time PCR detection the expression of odontoblast marker genes, and mineralization was evaluated by Alizarin Red S staining. GFP marked PDGFRβ + /c-kit + pulp cells were transplanted into emptied root canals of nude rat lower left incisors. Pulp-dentinal regeneration was examined by immunohistochemistry. PDGFRβ + /c-kit + pulp cells proliferated significantly faster than whole pulp cells. In mineralization media, PDGFRβ + /c-kit + pulp cells were able to develop under odontoblastic linage as demonstrated by a progressively increased expression of DMP1, DSPP, and osteocalcin. BMP2 seemed to enhance whereas PDGF-BB seemed to inhibit odontoblastic differentiation and mineralization of PDGFRβ + /c-kit + pulp cells. In vivo root canal transplantation study revealed globular dentin and pulp-like tissue formation by PDGFRβ + /c-kit + cells. PDGFRβ + /c-kit + pulp cells appear to have pulp stem cell potential capable of producing dentinal like structure in vitro and in vivo.

Stable nitrogen isotope analysis of dentine serial sections elucidate sex differences in weaning patterns of wild chimpanzees (Pan troglodytes).

Science.gov (United States)

Fahy, Geraldine E; Richards, Michael P; Fuller, Benjamin T; Deschner, Tobias; Hublin, Jean-Jacques; Boesch, Christophe

2014-04-01

Offspring provisioning is one of the most energetically demanding aspects of reproduction for female mammals. Variation in lactation length and weaning strategies between chimpanzees (Pan troglodytes), our closest living relative, and modern human societies have been reported. When and why these changes occurred is frequently debated. Our study used stable nitrogen isotope data of tooth root dentine from wild Western chimpanzees (Pan troglodytes verus) in Taï National Park, Côte d'Ivoire, to quantify weaning in these chimpanzees and explore if infant sex plays a role in maternal investment. We analyzed serial sections of deciduous lateral incisor root dentine from four Taï chimpanzees to establish the δ(15) N signal of nursing infants; we then analyzed serial sections of first permanent mandibular molar root dentine from 12 Taï chimpanzees to provide quantitative δ(15) N data on weaning in this population. Up to 2 years of age both sexes exhibited dentine δ(15) N values ≈2-3‰ higher than adult female Taï chimpanzees, consistent with a nursing signal. Thereafter a steady decrease in δ(15) N values consistent with the onset, and progression, of weaning, was visible. Sex differences were also evident, where male δ(15) N values decreased at a significantly slower rate compared to females. Confirmation of sex differences in maternal investment among Taï chimpanzees, demonstrates the viability of using isotope analysis to investigate weaning in non-human primates. Additionally, assuming that behaviors observed in the Taï chimpanzees are illustrative of the ancestral pattern, our results provide a platform to enable the trajectory of weaning in human evolution to be further explored. Copyright © 2013 Wiley Periodicals, Inc.

Shear bond strength of amalgam to dentin using different dentin adhesive systems

Directory of Open Access Journals (Sweden)

Farimah Sardari

2012-01-01

Full Text Available Background and Aims: The aim of this in vitro study was to assess the shear bond strength of amalgam to dentin using four dentin adhesive systems.Materials and Methods: One hundred human molars were selected. After enamel removal, a dentin cylinder with 3 mm thickness was prepared. Eighty specimens were resorted with amalgam and four dentin adhesive systems as follows (n=20: group 1, Scotch Bond Multi-Purpose; group 2, One Coat Bond; group 3, PQ1; and group 4, Panavia-F. In group 5, 20 specimens were resorted with amalgam and varnish as control group. The specimens were incubated at 37°C for 24 h. The shear bond strengths were then measured by using push out method. The data were analyzed by one-way ANOVA and post hoc Duncan's tests.Results: Mean values for bond strengths of test groups were as follows: group 1=21.03±8.9, group 2=23.47±9, group 3=13.16±8.8, group 4=20.07±8.9 and group 5=14.15±8.7 MPa±SD. One-way ANOVA showed the statistically significant difference between the bond strengths of five groups (P=0.001. Post hoc Duncan's test showed significant difference between groups 1and 3 (P=0.008, groups 1 and 5 (P=0.019, groups 2 and 5 (P=0.0008, groups 4 and 5 (P=0.042, and groups 3 and 4 (P=0.018.Conclusion: Results of this study showed that the bond strength of amalgam to dentin using One Coat Bond as dentin adhesive system was higher than that observed in other dentin adhesive systems.

Buffering action of human dentin in vitro.

Science.gov (United States)

Camps, J; Pashley, D H

2000-01-01

The purpose of this study was to determine the relative contributions of the mineral and organic phases of dentin to its total buffering capacity and to compare the buffering abilities of normal and caries-affected dentin for acids used in adhesive dentistry. Disks of normal and caries-affected human coronal dentin 0.6 mm thick were prepared. Fifty microL of various acids were applied to the surface of mineralized or completely demineralized dentin for varying lengths of time. They were collected from the surface and combined with water rinses to permit titration of the total amount of acid applied, the amount recovered, the total amount that was taken up by the dentin, and the amount that diffused across dentin into 1 mL of water. Equal volumes of acids were applied to mineralized or demineralized dentin powder or hydroxyapatite powder. About 88% to 90% of applied acid was recovered from the surface; only 10% to 12% of the acid was taken up by dentin. Of the H+ that was taken up, only 1% to 2% actually diffused across 0.6 mm of dentin. Increasing the application time of 37% phosphoric acid did not increase the amount of H+ that diffused across dentin. Increasing the concentration of phosphoric acid from 10% to 65% produced only slight increases in H+ diffusion across dentin. There was no difference in the buffering capacity of normal vs caries-affected dentin disks. Almost all of the buffering capacity of dentin is due to its mineral phase. The high buffering capacity of dentin and the high reactivity of H+ insure that little H+ diffuses through dentin more than 0.6 mm thick.

Effect of Collagen Matrix Saturation on the Surface Free Energy of Dentin using Different Agents.

Science.gov (United States)

de Almeida, Leopoldina de Fátima Dantas; Souza, Samilly Evangelista; Sampaio, Aline Araújo; Cavalcanti, Yuri Wanderley; da Silva, Wander José; Del Bel Cur, Altair A; Hebling, Josimeri

2015-07-01

The surface free energy of conditioned-dentin is one of the factors that interfere with monomeric infiltration of the interfibrillar spaces. Saturation of the tooth matrix with different substances may modulate this energy and, consequently, the wettability of the dentin. To evaluate the influence of different substances used to saturate conditioned-dentin on surface free energy (SFE) of this substrate. Dentin blocks (4 × 7 × 1 mm, n = 6/ group), obtained from the roots of bovine incisors, were etched using phosphoric acid for 15 seconds, rinsed and gently dried. The surfaces were treated for 60 seconds with: ultra-purified water (H20-control); ethanol (EtOH), acetone (ACT), chlorhexidine (CHX), ethylenediaminetetraacetic acid (EDTA); or sodium hypochlorite (NaOCl). The tooth surfaces were once again dried with absorbent paper and prepared for SFE evaluation using three standards: water, formamide and bromonaphthalene. Analysis of variance (ANOVA) and Dunnet's tests (a = 0.05) were applied to the data. Ethylenediaminetetraacetic acid was the only substance that caused a change to the contact angle for the standards water and formamide, while only EtOH influenced the angles formed between formamide and the dentin surface. None of the substances exerted a significant effect for bromonaphtha-lene. In comparison to the control, only EDTA and NaOCl altered both polar components of the SFE. Total SFE was increased by saturation of the collagen matrix by EDTA and reduced when NaOCl was used. Saturation of the collagen matrix by EDTA and EtOH changed the surface free energy of the dentin. In addition, the use of NaOCl negatively interfered with the properties evaluated. The increase of surface free energy and wettability of the dentin surface would allow higher penetration of the the adhesive system, which would be of importance to the clinical success of resin-dentin union.

Multi-walled carbon nanotubes/graphene oxide hybrid and nanohydroxyapatite composite: A novel coating to prevent dentin erosion.

Science.gov (United States)

Nahorny, Sídnei; Zanin, Hudson; Christino, Vinie Abreu; Marciano, Fernanda Roberta; Lobo, Anderson Oliveira; Soares, Luís Eduardo Silva

2017-10-01

To date is emergent the development of novel coatings to protect erosion, especially to preventive dentistry and restorative dentistry. Here, for the first time we report the effectiveness of multi-walled carbon nanotube/graphene oxide hybrid carbon-base material (MWCNTO-GO) combined with nanohydroxyapatite (nHAp) as a protective coating for dentin erosion. Fourier transform Raman spectroscopy (FT-Raman), scanning electron (SEM), and transmission electron (TEM) microscopy were used to investigated the coatings and the effect of acidulated phosphate fluoride gel (APF) treatment on bovine teeth root dentin before and after erosion. The electrochemical corrosion performance of the coating was evaluated. Raman spectra identified that: (i) the phosphate (ν 1 PO 4 3- ) content of dentin was not significantly affected by the treatments and (ii) the carbonate (ν 1 CO 3 2- ) content in dentin increased when nHAp was used. However, the nHAp/MWCNTO-GO composite exposited lower levels of organic matrix (CH bonds) after erosion compared to other treatments. Interesting, SEM micrographs identified that the nHAp/MWCNTO-GO formed layers after erosive cycling when associate with APF treatment, indicating a possible chemical bond among them. Treatments of root dentin with nHAp, MWCNTO-GO, APF_MWCNTO-GO, and APF_nHAp/MWCNTO-GO increased the carbonate content, carbonate/phosphate ratio, and organic matrix band area after erosion. The potentiodynamic polarization curves and Nyquist plot showed that nHAp, MWCNT-GO and nHAp/MWCNT-GO composites acted as protective agents against corrosion process. Clearly, the nHAp/MWCNTO-GO composite was stable after erosive cycling and a thin and acid-resistant film was formed when associated to APF treatment. Copyright © 2017 Elsevier B.V. All rights reserved.

Tensile bond strength of hydroxyethyl methacrylate dentin bonding agent on dentin surface at various drying techniques

Directory of Open Access Journals (Sweden)

Kun Ismiyatin

2010-06-01

Full Text Available Background: There are several dentin surface drying techniques to provide a perfect resin penetration on dentin. There are two techniques which will be compared in this study. The first technique was by rubbing dentin surface gently using cotton pellet twice, this technique is called blot dry technique. The second technique is by air blowing dentin surface for one second and continued by rubbing dentin surface gently using moist cotton. Purpose: This experiment was aimed to examine the best dentin surface drying techniques after 37% phosphoric acid etching to obtain the optimum tensile bond strength between hydroxyethyl methacrylate (HEMA and dentin surface. Method: Bovine teeth was prepared flat to obtain the dentin surface and than was etched using 37% phosphoric acid for 15 seconds. After etching the dentin was cleaned using 20 cc plain water and dried with blot dry techniques (group I, or dried with air blow for one second (group II, or dried with air blow for one second, and continued with rubbing gently using moist cotton pellet (group III, and without any drying as control group (group IV. After these drying, the dentin surfaces were applied with resin dentin bonding agent and put into plunger facing the composite mould. The antagonist plunger was filled with composite resin. After 24 hours, therefore bond strength was measured using Autograph. Result: Data obtained was analyzed using One-Way ANOVA with 95% confidence level and continued with LSD test on p≤0.05. The result showed that the highest tensile bond strength was on group I, while the lowest on group IV. Group II and IV, III and IV, II and III did not show signigicant difference (p>0.05. Conclusion: Dentin surface drying techniques through gentle rubbing using cotton pellet twice (blot dry technique gave the greatest tensile bond strength.Latar belakang masalah: Tehnik pengeringan permukaan dentin agar resin dapat penetrasi dengan sempurna adalah dengan cara pengusapan secara

Effects of matrix metallproteinases on dentin bonding and strategies to increase durability of dentin adhesion

Directory of Open Access Journals (Sweden)

Jung-Hyun Lee

2012-02-01

Full Text Available The limited durability of resin-dentin bonds severely compromises the longevity of composite resin restorations. Resin-dentin bond degradation might occur via degradation of water-rich and resin sparse collagen matrices by host-derived matrix metalloproteinases (MMPs. This review article provides overview of current knowledge of the role of MMPs in dentin matrix degradation and four experimental strategies for extending the longevity of resin-dentin bonds. They include: (1 the use of broad-spectrum inhibitors of MMPs, (2 the use of cross-linking agents for silencing the activities of MMPs, (3 ethanol wet-bonding with hydrophobic resin, (4 biomimetic remineralization of water-filled collagen matrix. A combination of these strategies will be able to overcome the limitations in resin-dentin adhesion.

Effects of Fungicides, Essential Oils and Gamma Irradiated Bioagents on Chickpea Root Rot Caused by Sclerotium rolfsii

International Nuclear Information System (INIS)

El-Batal, A.I.; Fathy, R.M.; Ismail, A.A.; Mubark, H.M.; Mahmoud, Y.A.

2011-01-01

Sclerotium rolfsii (S. rolfsii) causes root rot disease in several crops including Cicer arietinum (chickpea) that results in low yield. In vitro experiments on fungicides, vitavax and monceren T, and essential oils, clove and mint oils, were conducted to control root rot disease of chickpea caused by S. rolfsii. The treatments resulted in 80 % suppression of root rot disease. Gliocladium virens (G. virens) and Gliocladium deliquescens (G. deliquescens) were effective as biocontrol agents against S. rolfsii. The results showed that these treatments greatly reduced the root rot disease in chickpea. In this study, the effect of gamma irradiation at doses 0, 0.25, 0.5, 1.0, 1.5, 2.0, 2.5 and 3.0 kGy on the pathogenecity of G. virens and G. deliquescens against S. rolfsii were investigated. The results revealed that gamma irradiation increased the pathogenecity of G. virens and G. deliquescens against S. rolfsii

Evaluation of the tensile bond strength of an adhesive system self-etching in dentin irradiated with Er:YAG laser; Avaliacao da resistencia a tracao de um sistema adesivo self-etching em dentina irradiada com Er:YAG laser

Energy Technology Data Exchange (ETDEWEB)

Mello, Andrea Malluf Dabul de

2000-07-01

Since Buonocore (1955), several researchers have been seeking for the best adhesive system and treatment for the enamel and dentin surfaces. The use of the acid has been presented as one of the best techniques of dentin conditioning , because this promotes the removal of the 'smear layer and exhibition of dentinal structure, for a best penetration and micro- retention of the adhesive system. However, some conditioning methods have been appearing in the literature, for the substitution or interaction with the acid substances, as the laser. The objective of this work is to evaluate the tensile bond strength of the adhesive system self-etching' associated to a composed resin, in dentin surfaces conditioned with the Er:YAG laser. For this study, freshly extracted human teeth were used and in each one the dentinal surfaces , which were treated with three sandpapers of different granulations (120,400,600), to obtain a standard of the smear layer, before the irradiation of the laser and of the restoring procedure. After these procedures the specimens were storage in distilled water at 37 deg C for 24 hours. Soon after, they were submitted to the tensile strength test .After analyzing the results, we can concluded that the use of the Er:YAG laser can substitute the drill without the need of conditioning, when using the adhesive system 'self-etching' in the dentinal surfaces because there was a decline in the strength of adhesion in the groups conditioned with the laser. (author)

A laser-abrasive method for the cutting of enamel and dentin.

Science.gov (United States)

Altshuler, G B; Belikov, A V; Sinelnik, Y A

2001-01-01

This paper introduced a new method for the removal of hard dental tissue based upon the use of particles accelerated by laser irradiation, which the authors have called the laser-abrasive method. The particles used were sapphire as powder or an aqueous suspension. The effect of the products of enamel ablation was also investigated. The particles were accelerated using submillisecond pulses of Er:YAG and Nd:YAG lasers. A strobing CCD camera was used to measure the speed of the ejected particles. The additional contribution of these particles to the efficiency of laser ablation of enamel and dentin was also investigated. The results showed that the enamel particles produced by the beam-tissue interaction were also accelerated by this process of ablation and were effective in the removal of enamel and dentin. The use of an aqueous suspension of sapphire particles increased the efficiency of enamel removal threefold when compared with the use of an Er:YAG laser with water spray. The laser-abrasive method allowed for the removal of enamel and dentin at speeds approaching those of the high-speed turbine. Copyright 2001 Wiley-Liss, Inc.

Root Conditioning and Agents Effect in Regeneration of Periodontal Tissue

Directory of Open Access Journals (Sweden)

Kadkhoda Z

1999-12-01

Full Text Available Periodontitis affected root surfaces are hypermineralized and contaminated with cytotoxic and"nother biologically active substances."nThe instrumented surface will inervitably be coverd by a smear layer following root planing with or without flap."nSmear layer is resistant to saline rinsing, but may be removed with agents such as acids (e.g.citric acid, tetracyclines, EDTA, and laser."nLow pH aqueous solutions such as citric acid have been used in surgical periodontal therapy mainly for two reasons, It dissolves smear layer after a relatively short exposure time and it has been claimed to selectively remove root surface associated mineral exposing collagen to varying degrees. A root surface coated with collagen appears to be a preferred surface for fibroblast attachment, a cellular event fundamental to successful periodontal wound healing."nSeveral studies indicate the potential of tetracycline (TTE-HCL in periodontal regeneration. Its acidic pH suggest that it can be used as a demineralization agent and removing the smear layer and exposing collagen matrix of the dentin."nChalating agent (EDTA working at neutral pH appears preferable with respect to preserving the integrity of exposed collagen fibers, early colonization, and wound healing. In addition, etching at neutral pH has been reported preserve adjacent tissue- vitality, while etching at low pH necrotizes the fiap and adjacent periodontium."nClinical and subclinical studies have demonstrated laser waves can remove calculus and bacterial plaque and pocket epithelium and strile the root surface and can expose the dentin collagen and dentinal tublules, and leads to pronounce reducing of probing depth around teeth diseased with periodontitis.

Bond strength of etch-and-rinse and self-etch adhesive systems to enamel and dentin irradiated with a novel CO2 9.3 μm short-pulsed laser for dental restorative procedures.

Science.gov (United States)

Rechmann, Peter; Bartolome, N; Kinsel, R; Vaderhobli, R; Rechmann, B M T

2017-12-01

The objective of this study was to evaluate the influence of CO 2 9.3 μm short-pulsed laser irradiation on the shear bond strength of composite resin to enamel and dentin. Two hundred enamel and 210 dentin samples were irradiated with a 9.3 µm carbon dioxide laser (Solea, Convergent Dental, Inc., Natick, MA) with energies which either enhanced caries resistance or were effective for ablation. OptiBond Solo Plus [OptiBondTE] (Kerr Corporation, Orange, CA) and Peak Universal Bond light-cured adhesive [PeakTE] (Ultradent Products, South Jordan, UT) were used. In addition, Scotchbond Universal [ScotchbondSE] (3M ESPE, St. Paul, MN) and Peak SE self-etching primer with Peak Universal Bond light-cured adhesive [PeakSE] (Ultradent Products) were tested. Clearfil APX (Kuraray, New York, NY) was bonded to the samples. After 24 h, a single plane shear bond test was performed. Using the caries preventive setting on enamel resulted in increased shear bond strength for all bonding agents except for self-etch PeakSE. The highest overall bond strength was seen with PeakTE (41.29 ± 6.04 MPa). Etch-and-rinse systems achieved higher bond strength values to ablated enamel than the self-etch systems did. PeakTE showed the highest shear bond strength with 35.22 ± 4.40 MPa. OptiBondTE reached 93.8% of its control value. The self-etch system PeakSE presented significantly lower bond strength. The shear bond strength to dentin ranged between 19.15 ± 3.49 MPa for OptiBondTE and 43.94 ± 6.47 MPa for PeakSE. Etch-and-rinse systems had consistently higher bond strength to CO 2 9.3 µm laser-ablated enamel. Using the maximum recommended energy for dentin ablation, the self-etch system PeakSE reached the highest bond strength (43.9 ± 6.5 MPa).

Effect of high energy X-ray irradiation on the nano-mechanical properties of human enamel and dentine

Energy Technology Data Exchange (ETDEWEB)

Liang, Xue; Zhang, Jing Yang; Cheng, Iek Ka [State Key Laboratory of Oral Diseases, Sichuan University, Chengdu (China); Li, Ji Yao, E-mail: jiyao_li@aliyun.com [West China School of Stomatology, Sichuan University, Chengdu (China)

2016-05-01

Radiotherapy for malignancies in the head and neck can cause common complications that can result in tooth damage that are also known as radiation caries. The aim of this study was to examine damage to the surface topography and calculate changes in friction behavior and the nano-mechanical properties (elastic modulus, nano hardness and friction coefficient) of enamel and dentine from extracted human third molars caused by exposure to radiation. Enamel and dentine samples from 50 human third molars were randomly assigned to four test groups or a control group. The test groups were exposed to high energy X-rays at 2 Gy/day, 5 days/week for 5 days (10 Gy group), 15 days (30 Gy group), 25 days (50 Gy group), 35 days (70 Gy group); the control group was not exposed. The nano hardness, elastic modulus, and friction coefficient were analyzed using a Hysitron Triboindenter. The nano-mechanical properties of both enamel and dentine showed significant dose-response relationships. The nano hardness and elastic modulus were most variable between 30-50 Gy, while the friction coefficient was most variable between 0-10 Gy for dentine and 30-50 Gy for enamel. After exposure to X-rays, the fracture resistance of the teeth clearly decreased (rapidly increasing friction coefficient with increasing doses under the same load), and they were more fragile. These nano-mechanical changes in dental hard tissue may increase the susceptibility to caries. Radiotherapy caused nano-mechanical changes in dentine and enamel that were dose related. The key doses were 30-50 Gy and the key time points occurred during the 15{sup th}-25{sup th} days of treatment, which is when application of measures to prevent radiation caries should be considered. (author)

Effect of high energy X-ray irradiation on the nano-mechanical properties of human enamel and dentine

Directory of Open Access Journals (Sweden)

Xue LIANG

2016-01-01

Full Text Available Abstract Radiotherapy for malignancies in the head and neck can cause common complications that can result in tooth damage that are also known as radiation caries. The aim of this study was to examine damage to the surface topography and calculate changes in friction behavior and the nano-mechanical properties (elastic modulus, nanohardness and friction coefficient of enamel and dentine from extracted human third molars caused by exposure to radiation. Enamel and dentine samples from 50 human third molars were randomly assigned to four test groups or a control group. The test groups were exposed to high energy X-rays at 2 Gy/day, 5 days/week for 5 days (10 Gy group, 15 days (30 Gy group, 25 days (50 Gy group, 35 days (70 Gy group; the control group was not exposed. The nanohardness, elastic modulus, and friction coefficient were analyzed using a Hysitron Triboindenter. The nano-mechanical properties of both enamel and dentine showed significant dose-response relationships. The nanohardness and elastic modulus were most variable between 30-50 Gy, while the friction coefficient was most variable between 0-10 Gy for dentine and 30-50 Gy for enamel. After exposure to X-rays, the fracture resistance of the teeth clearly decreased (rapidly increasing friction coefficient with increasing doses under the same load, and they were more fragile. These nano-mechanical changes in dental hard tissue may increase the susceptibility to caries. Radiotherapy caused nano-mechanical changes in dentine and enamel that were dose related. The key doses were 30-50 Gy and the key time points occurred during the 15th-25th days of treatment, which is when application of measures to prevent radiation caries should be considered.

Effect of high energy X-ray irradiation on the nano-mechanical properties of human enamel and dentine

International Nuclear Information System (INIS)

Liang, Xue; Zhang, Jing Yang; Cheng, Iek Ka; Li, Ji Yao

2016-01-01

Radiotherapy for malignancies in the head and neck can cause common complications that can result in tooth damage that are also known as radiation caries. The aim of this study was to examine damage to the surface topography and calculate changes in friction behavior and the nano-mechanical properties (elastic modulus, nano hardness and friction coefficient) of enamel and dentine from extracted human third molars caused by exposure to radiation. Enamel and dentine samples from 50 human third molars were randomly assigned to four test groups or a control group. The test groups were exposed to high energy X-rays at 2 Gy/day, 5 days/week for 5 days (10 Gy group), 15 days (30 Gy group), 25 days (50 Gy group), 35 days (70 Gy group); the control group was not exposed. The nano hardness, elastic modulus, and friction coefficient were analyzed using a Hysitron Triboindenter. The nano-mechanical properties of both enamel and dentine showed significant dose-response relationships. The nano hardness and elastic modulus were most variable between 30-50 Gy, while the friction coefficient was most variable between 0-10 Gy for dentine and 30-50 Gy for enamel. After exposure to X-rays, the fracture resistance of the teeth clearly decreased (rapidly increasing friction coefficient with increasing doses under the same load), and they were more fragile. These nano-mechanical changes in dental hard tissue may increase the susceptibility to caries. Radiotherapy caused nano-mechanical changes in dentine and enamel that were dose related. The key doses were 30-50 Gy and the key time points occurred during the 15 th -25 th days of treatment, which is when application of measures to prevent radiation caries should be considered. (author)

The biomineralization ability of mineral trioxide aggregate and Portland cement on dentin enhances the push-out strength.

Science.gov (United States)

Reyes-Carmona, Jessie F; Felippe, Mara S; Felippe, Wilson T

2010-02-01

Recently, it was shown that the interaction of each of mineral trioxide aggregate (MTA) and Portland cement with dentin in phosphate-buffered saline (PBS) promotes a biomineralization process that leads to the formation of an interfacial layer with tag-like structures at the cement-dentin interface. This study analyzes the influence of the biomineralization process on the push-out strength of ProRoot MTA (Dentsply Tulsa Dental, Tulsa, OK), MTA Branco (Angelus Soluções Odontológicas, Londrina, PR, Brazil), MTA BIO (Angelus Soluções Odontológicas), or Portland cement with and without calcium chloride. Dentin discs with standardized cavities were filled with ProRoot MTA, MTA Branco, MTA BIO, white Portland cement + 20% bismuth oxide (PC1), or PC1 + 10% of calcium chloride (PC2). The specimens were randomly divided into two groups: cement in contact with a wet cotton pellet for 72 hours or immersed in PBS for 2 months. The bond strengths were measured with the Instron Testing machine (Model 4444; Instron Corp, Canton, MA), and the fractured surfaces on the root walls were observed by scanning electron microscopy. All samples immersed in PBS displayed a significantly greater resistance to displacement than that observed for the samples in contact with a wet cotton pellet for 72 hours (p Portland cements. It was concluded that the biomineralization process positively influenced the push-out bond strength of the cements, particularly the MTA groups. Copyright 2010 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Stabilizing sodium hypochlorite at high pH: effects on soft tissue and dentin.

Science.gov (United States)

Jungbluth, Holger; Marending, Monika; De-Deus, Gustavo; Sener, Beatrice; Zehnder, Matthias

2011-05-01

When sodium hypochlorite solutions react with tissue, their pH drops and tissue sorption decreases. We studied whether stabilizing a NaOCl solution at a high pH would increase its soft-tissue dissolution capacity and effects on the dentin matrix compared with a standard NaOCl solution of the same concentration and similar initial pH. NaOCl solutions were prepared by mixing (1:1) a 10% stock solution with water (standard) or 2 mol/L NaOH (stabilized). Physiological saline and 1 mol/L NaOH served as the controls. Chlorine content and alkaline capacity of NaOCl solutions were determined. Standardized porcine palatal soft-tissue specimens and human root dentin bars were exposed to test and control solutions. Weight loss percentage was assessed in the soft-tissue dissolution assay. Three-point bending tests were performed on the root dentin bars to determine the modulus of elasticity and flexural strength. Values between groups were compared using one-way analysis of variance with the Bonferroni correction for multiple testing (α pH level of 7.5, respectively. The stabilized NaOCl dissolved significantly more soft tissue than the standard solution, and the pH remained high. It also caused a higher loss in elastic modulus and flexure strength (P < .05) than the control solutions, whereas the standard solution did not. NaOH-stabilized NaOCl solutions have a higher alkaline capacity and are thus more proteolytic than standard counterparts. Copyright © 2011 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Hereditary dentine disorders: dentinogenesis imperfecta and dentine dysplasia

Directory of Open Access Journals (Sweden)

MacKie Iain

2008-11-01

Full Text Available Abstract The hereditary dentine disorders, dentinogenesis imperfecta (DGI and dentine dysplasia (DD, comprise a group of autosomal dominant genetic conditions characterised by abnormal dentine structure affecting either the primary or both the primary and secondary dentitions. DGI is reported to have an incidence of 1 in 6,000 to 1 in 8,000, whereas that of DD type 1 is 1 in 100,000. Clinically, the teeth are discoloured and show structural defects such as bulbous crowns and small pulp chambers radiographically. The underlying defect of mineralisation often results in shearing of the overlying enamel leaving exposed weakened dentine which is prone to wear. Currently, three sub-types of DGI and two sub-types of DD are recognised but this categorisation may change when other causative mutations are found. DGI type I is inherited with osteogenesis imperfecta and recent genetic studies have shown that mutations in the genes encoding collagen type 1, COL1A1 and COL1A2, underlie this condition. All other forms of DGI and DD, except DD-1, appear to result from mutations in the gene encoding dentine sialophosphoprotein (DSPP, suggesting that these conditions are allelic. Diagnosis is based on family history, pedigree construction and detailed clinical examination, while genetic diagnosis may become useful in the future once sufficient disease-causing mutations have been discovered. Differential diagnoses include hypocalcified forms of amelogenesis imperfecta, congenital erythropoietic porphyria, conditions leading to early tooth loss (Kostmann's disease, cyclic neutropenia, Chediak-Hegashi syndrome, histiocytosis X, Papillon-Lefevre syndrome, permanent teeth discolouration due to tetracyclines, Vitamin D-dependent and vitamin D-resistant rickets. Treatment involves removal of sources of infection or pain, improvement of aesthetics and protection of the posterior teeth from wear. Beginning in infancy, treatment usually continues into adulthood with a

Thermal analysis of different application techniques on Nd:YAG laser after root canal preparation of single-rooted teeth; Analise termica de diferentes tecnicas de utilizacao do laser de Nd:YAG apos o preparo quimico-cirurgico de dentes unirradiculares

Energy Technology Data Exchange (ETDEWEB)

Archilla, Jose Ricardo de F

2001-07-01

The experiment objective is to analyze temperature variation, by means of three different application techniques of Nd:YAG laser in the root canals of singlerooted anterior teeth. Three root canals were instrumented, irrigated, X-rayed to measure the remaining dentin in the apical area and submitted to laser irradiation techniques used by Gutknecht, Matsumoto and a new technique with oscillatory movement. The used laser parameters were: pulse energy 250 mJ, frequency 5 Hz, pulse fluency 354 J/cm{sup 2}, average potency 1,25 W, pulse width 300 {mu}s, fiber core diameter 300 {mu}s and interval of thermal relaxation of 20 s. After temperature evaluation and interpretation of the obtained data, it was concluded: 1) the oscillatory technique provided a better heat distribution during the laser application, when analyzing the graphs separately; 2) all the used techniques are within a pattern of safety, analyzing the average and highest temperatures of the apical area and the middle third, even so, disrespecting the last application day and the middle third of root 'C'.(author)

Thermal analysis of different application techniques on Nd:YAG laser after root canal preparation of single-rooted teeth; Analise termica de diferentes tecnicas de utilizacao do laser de Nd:YAG apos o preparo quimico-cirurgico de dentes unirradiculares

Energy Technology Data Exchange (ETDEWEB)

Archilla, Jose Ricardo de F

2001-07-01

The experiment objective is to analyze temperature variation, by means of three different application techniques of Nd:YAG laser in the root canals of singlerooted anterior teeth. Three root canals were instrumented, irrigated, X-rayed to measure the remaining dentin in the apical area and submitted to laser irradiation techniques used by Gutknecht, Matsumoto and a new technique with oscillatory movement. The used laser parameters were: pulse energy 250 mJ, frequency 5 Hz, pulse fluency 354 J/cm{sup 2}, average potency 1,25 W, pulse width 300 {mu}s, fiber core diameter 300 {mu}s and interval of thermal relaxation of 20 s. After temperature evaluation and interpretation of the obtained data, it was concluded: 1) the oscillatory technique provided a better heat distribution during the laser application, when analyzing the graphs separately; 2) all the used techniques are within a pattern of safety, analyzing the average and highest temperatures of the apical area and the middle third, even so, disrespecting the last application day and the middle third of root 'C'.(author)

Pengaruh Konsentrasi dan Lama Aplikasi Sodium Hipoklorit (NaOCL sebagai Bahan Irigasi Saluran Akar terhadap Kekuatan Geser Perlekatan Siler Berbahan Dasar Resin Pada Dentin Saluran Akar

Directory of Open Access Journals (Sweden)

Tunjung Nugraheni

2012-07-01

menit dengan kelompok yang diirigasi NaOCI 5% selama 10 menit. Kesimpulan. Kekuatan geser perlekatan siler berbahan dasar resin pada dentin saluran akar berbeda setelah diirigasi NaOCI dengan konsentrasi dan waktu irigasi yang berbeda.   Background. Biomechanichal preparationin of root canal treatment used 0,5-5,25% sodium Hypochlorite as root canal irrigation, that may effect to physical properties of dentin. The purpose of this study was to find out the effect of concentration and duration application of sodium hypochlorite to shear bond strength of sealer resin based to root canal dentin. Methods. Thirthy premolar were splitted buccolingual then pulp tissue were cleaned out, smoothed and fixed into acrylic resin cast. They were devided into 2 group, group I were soaking into NaOCI 2,5% group II were soaking into NaOCI 5%. Group I and II were devided into 3 subgroup, group a were soaking 5 minutes, group b were soaking 10 minutes. Group c were soaking 15 minutes. Then sealer cast were fixed and filled with sealer resin-based, and incubated for 74 hours. They were tested for shear bond strength with Universal Testing Machine. The data were analyzed with two way Anava and LSD. Result. Two way Avana show that shear bond strength of sealer resin-based to root canal after irrigation with different concentration and duration application of sodium hypochlorite are significant. Conclusion. Shear bond strength of sealer resin-based to root canal dentin after irrigation with different concentration and duration application of sodium hypochlorite are different.

Damage to root dentin during retreatment procedures

NARCIS (Netherlands)

Shemesh, H.; Roeleveld, A.C.; Wesselink, P.R.; Wu, M.K.

2011-01-01

Introduction: The aim of this study was to explore the influence of retreatment procedures on the appearance of defects on the root canal walls. Methods: Two hundred mandibular premolars were divided into 4 groups. One group was left unprepared. The rest of the teeth were prepared with ProTaper

Effect of citric acid, tetracycline, and doxycycline on instrumented periodontally involved root surfaces: A SEM study

Directory of Open Access Journals (Sweden)

Gurparkash Singh Chahal

2014-01-01

Full Text Available Background: A surface smear layer consisting of organic and inorganic material is formed on the root surface following mechanical instrumentation and may inhibit the formation of new connective tissue attachment to the root surface. Modification of the tooth surface by root conditioning has resulted in improved connective tissue attachment and has advanced the goal of reconstructive periodontal treatment. Aim: The aim of this study was to compare the effects of citric acid, tetracycline, and doxycycline on the instrumented periodontally involved root surfaces in vitro using a scanning electron microscope. Settings and Design: A total of 45 dentin samples obtained from 15 extracted, scaled, and root planed teeth were divided into three groups. Materials and Methods: The root conditioning agents were applied with cotton pellets using the "Passive burnishing technique" for 5 minutes. The samples were then examined by the scanning electron microscope. Statistical Analysis Used: The statistical analysis was carried out using Statistical Package for Social Sciences (SPSS Inc., Chicago, IL, version 15.0 for Windows. For all quantitative variables means and standard deviations were calculated and compared. For more than two groups ANOVA was applied. For multiple comparisons post hoc tests with Bonferroni correction was used. Results: Upon statistical analysis the root conditioning agents used in this study were found to be effective in removing the smear layer, uncovering and widening the dentin tubules and unmasking the dentin collagen matrix. Conclusion: Tetracycline HCl was found to be the best root conditioner among the three agents used.

Effects of adsorbed and templated nanosilver in mesoporous calcium-silicate nanoparticles on inhibition of bacteria colonization of dentin

Directory of Open Access Journals (Sweden)

Fan W

2014-11-01

Full Text Available Wei Fan,1,* Daming Wu,1,* Franklin R Tay,2 Tengjiao Ma,1 Yujie Wu,1 Bing Fan1 1The State Key Laboratory Breeding Base of Basic Science of Stomatology (Hubei-MOST and Key Laboratory of Oral Biomedicine Ministry of Education, School and Hospital of Stomatology, Wuhan University, Wuhan, People’s Republic of China; 2Department of Endodontics, Georgia Regents University, Augusta, Georgia, USA *These authors contributed equally to this work Abstract: Mesoporous calcium-silicate nanoparticles (MCSNs are advanced biomaterials for controlled drug delivery and mineralization induction. Nanosilver-incorporated MCSNs (Ag-MCSNs were prepared in the present study using both the adsorption and template methods. Both versions of Ag-MCSNs showed characteristic morphology of mesoporous materials and exhibited sustained release of ions over time. In antibacterial testing against planktonic Enterococcus faecalis, Ag-MCSNs showed significantly better antibacterial effects when compared with MCSNs (P<0.05. The Ag-MCSNs aggregated on the dentin surface of root canal walls and infiltrated into dentinal tubules after ultrasound activation, significantly inhibiting the adherence and colonization of E. faecalis on dentin (P<0.05. Despite this, Ag-MCSNs with templated nanosilver showed much lower cytotoxicity than Ag-MCSNs with adsorbed nanosilver (P<0.05. The results of the present study indicated that nanosilver could be incorporated into MCSNs using the template method. The templated nanosilver could release silver ions and inhibit the growth and colonization of E. faecalis both in the planktonic form and as biofilms on dentin surfaces as absorbed nanosilver. Templated Ag-MCSNs may be developed into a new intracanal disinfectant for root canal disinfection due to their antibacterial ability and low cytotoxicity, and as controlled release devices for other bioactive molecules to produce multifunctional biomaterials. Keywords: antibacterial effect, mesoporosity

Influence of 60Co irradiation on the mandible of adult rabbit

International Nuclear Information System (INIS)

Umezaki, Yukio

1977-01-01

This study was performed in order to observe the effect of 60 Co γ-ray irradiation (5000, 8000 and 10000R) on rabbits' mandible, for as long as possible, approximately 18 months. Radiographical and histopathological studies were done after irradiation. The upper anterior teeth of all experimental animals showed elongation, lateral flection and diasthema. The lower anterior teeth showed shortening or disappearance of the crowns and resorption of the root apex in all. These teeth were lost eventually. Molar teeth disclosed shortening of crowns and irregular and partial loss on the surface of the dentine. Pulp chambers were extremely narrowed. These changes were most conspicuous in the 10,000R irradiation group. Mandibular fractures occurred in 13 cases, which include 3 cases with 5,000R, 4 cases with 8,000R and 6 cases with 10,000R. The alveolar bones were resorped, and were replaced with mandibular bone trabeculae. Various types of ankylosis of root surface and mandibulars were seen. These changes were more frequently noted in the molar regions that the anterior regions and in the groups with higher doses and longer days after irradiation. Bone trabeculae and cortex of the mandibles were resorped in the 3 irradiation groups in the early stage, but regeneration and thickening of the bones occured later. The usual case was that the anterior bone marrow became more gelatinous and the molar marrow became more fibrous. Hyperemia and abscess formation were recognized in some cases. Although in the molar regions these pathological changes were conspicuous in proportion to the amount of dose, in the anterior regions, the same changes were more conspicuous in the 5,000R irradiation group than in the 8,000R group. (J.P.N.)

Modification of dentin surface to enamel-like structure: A potential strategy for improving dentin bonding durability, desensitizing and self-repairing

Directory of Open Access Journals (Sweden)

Hongye Yang

2014-01-01

Full Text Available Introduction: Current theories of dentin bonding are based on the concept of "hybrid layer". However, the histological complexity of dentin, as well as the vulnerability of the hybrid layer, goes against the long-term effect of dentin bonding. At the same time, post-operative sensitivity is more likely to occur after traditional adhesive restoration. The Hypothesis: Compared to dentin bonding, enamel bonding exhibits a more optimal immediate and long-term performance, owing to its higher degree of mineralization, well-arranged enamel crystals and the porous structure after etching. Moreover, "enamel hypersensitivity" is never going to happen due to the lack of tubules existing in dentin. In light of this phenomenon, we brought up the concept and the proposal method to form an "enamel-like" dentin, simulating enamel structure to achieve satisfying durability of dentin bonding and obtain good performance for preventing post-operative sensitivity. With the application of mesoporous silicon bi-directionally binding to hydroxyapatite of dentin itself and hydroxyapatite nanorods synthetized in vitro, we may be able to form an enamel-like "functional layer" via ion-regulating self-assembly. Evaluation of Hypothesis: This paper explains how to achieve dentin enamel-like modification by chemical methods, especially, details the strategies and possible mechanisms of the hypothesis. Validation of the hypothesis is more likely to eliminate the adverse effect of dentinal fluid, improve long-term performance of dentin bonding, offer strategies for desensitizing treatment and self-repairing carious-affected dentin, and furthermore, provide the possibility to introduce new theories of dentin bonding.

Polymer Nanocarriers for Dentin Adhesion

Science.gov (United States)

Osorio, R.; Osorio, E.; Medina-Castillo, A.L.; Toledano, M.

2014-01-01

To obtain more durable adhesion to dentin, and to protect collagen fibrils of the dentin matrix from degradation, calcium- and phosphate-releasing particles have been incorporated into the dental adhesive procedure. The aim of the present study was to incorporate zinc-loaded polymeric nanocarriers into a dental adhesive system to facilitate inhibition of matrix metalloproteinases (MMPs)-mediated collagen degradation and to provide calcium ions for mineral deposition within the resin-dentin bonded interface. PolymP-nActive nanoparticles (nanoMyP) were zinc-loaded through 30-minute ZnCl2 immersion and tested for bioactivity by means of 7 days’ immersion in simulated body fluid solution (the Kokubo test). Zinc-loading and calcium phosphate depositions were examined by scanning and transmission electron microscopy, elemental analysis, and x-ray diffraction. Nanoparticles in ethanol solution infiltrated into phosphoric-acid-etched human dentin and Single Bond (3M/ESPE) were applied to determine whether the nanoparticles interfered with bonding. Debonded sticks were analyzed by scanning electron microscopy. A metalloproteinase collagen degradation assay was also performed in resin-infiltrated dentin with and without nanoparticles, measuring C-terminal telopeptide of type I collagen (ICTP) concentration in supernatants, after 4 wk of immersion in artificial saliva. Numerical data were analyzed by analysis of variance (ANOVA) and Student-Newman-Keuls multiple comparisons tests (p calcium regardless of zinc incorporation. Nanoparticles failed to infiltrate demineralized intertubular dentin and remained on top of the hybrid layer, without altering bond strength. Calcium and phosphorus were found covering nanoparticles at the hybrid layer, after 24 h. Nanoparticle application in etched dentin also reduced MMP-mediated collagen degradation. Tested nanoparticles may be incorporated into dental adhesive systems to provide the appropriate environment in which dentin MMP

Potential to induce dentinal cracks during retreatment procedures of teeth treated with “Russian red”: An ex vivo study

Directory of Open Access Journals (Sweden)

Eglė Nedzinskienė

2017-01-01

Conclusions: Retreatment methods had a damaging effect on the root dentin of teeth previously treated with resorcinol–formaldehyde resin. At magnification ×16, the efficacy of using the dye for the detection of cracks was higher than detection without the dye.

The shear bond strength of self-adhesive resin cements to dentin and enamel: an in vitro study.

Science.gov (United States)

Rodrigues, Raphaela F; Ramos, Carla M; Francisconi, Paulo A S; Borges, Ana Flávia S

2015-03-01

Clinicians continue to search for ways to simplify bonding procedures without compromising clinical efficacy. The purpose of this study was to evaluate the shear strength of self-adhesive cements RelyX U100 and RelyX U200, and conventional resin cement RelyX ARC to enamel and dentin after different surface treatments. The crowns of 120 bovine incisor teeth were separated from the roots and embedded in epoxy resin in polyvinyl chloride tubes. In each tooth, the area to be cemented was delimited with central holed adhesive tape. The teeth were distributed into 12 groups (n=10) according to the substrate; etched or not with 37% phosphoric acid; and cement type of enamel-U100, enamel-phosphoric acid-U100, enamel-U200, enamel-phosphoric acid-U200, enamel-ARC, enamel-phosphoric acid-ARC, dentin-U100, dentin-phosphoric acid-U100, dentin-U200, dentin-phosphoric acid-U200, dentin-ARC, and dentin-phosphoric acid-ARC. After 7 days of storage in artificial saliva, shear strength tests were performed by using a universal testing machine (0.5 mm/min). The data were analyzed with 3-way ANOVA and the Tukey test (α=.05). Fracture analysis was performed with a light microscope. Two specimens from each group were analyzed with a scanning electron microscope. In enamel, ARC (9.96 MPa) had higher shear strength (P=.038) than U100 (5.14 MPa); however, after surface etching, U100 (17.81 MPa) and U200 (17.52 MPa) had higher shear strength (Padhesive type. U200 self-adhesive cement had similar bond strength to the ARC in enamel, but the combination with phosphoric acid had the best bond strength. For dentin, self-adhesive resin cements are equally effective alternatives to conventional resin cement. Copyright © 2015 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Exploiting the potential of free software to evaluate root canal biomechanical preparation outcomes through micro-CT images.

Science.gov (United States)

Neves, A A; Silva, E J; Roter, J M; Belladona, F G; Alves, H D; Lopes, R T; Paciornik, S; De-Deus, G A

2015-11-01

To propose an automated image processing routine based on free software to quantify root canal preparation outcomes in pairs of sound and instrumented roots after micro-CT scanning procedures. Seven mesial roots of human mandibular molars with different canal configuration systems were studied: (i) Vertucci's type 1, (ii) Vertucci's type 2, (iii) two individual canals, (iv) Vertucci's type 6, canals (v) with and (vi) without debris, and (vii) canal with visible pulp calcification. All teeth were instrumented with the BioRaCe system and scanned in a Skyscan 1173 micro-CT before and after canal preparation. After reconstruction, the instrumented stack of images (IS) was registered against the preoperative sound stack of images (SS). Image processing included contrast equalization and noise filtering. Sound canal volumes were obtained by a minimum threshold. For the IS, a fixed conservative threshold was chosen as the best compromise between instrumented canal and dentine whilst avoiding debris, resulting in instrumented canal plus empty spaces. Arithmetic and logical operations between sound and instrumented stacks were used to identify debris. Noninstrumented dentine was calculated using a minimum threshold in the IS and subtracting from the SS and total debris. Removed dentine volume was obtained by subtracting SS from IS. Quantitative data on total debris present in the root canal space after instrumentation, noninstrumented areas and removed dentine volume were obtained for each test case, as well as three-dimensional volume renderings. After standardization of acquisition, reconstruction and image processing micro-CT images, a quantitative approach for calculation of root canal biomechanical outcomes was achieved using free software. © 2014 International Endodontic Journal. Published by John Wiley & Sons Ltd.

Efficacy of stannous, fluoride and their their combination in dentin erosion prevention in vitro

Directory of Open Access Journals (Sweden)

Amnah Abdullah ALGARNI

2015-01-01

Full Text Available The aim of this study was to compare the protective effects of solutions containing stannous (Sn, fluoride (F and their combination in the prevention of dentin erosion. Forty bovine root dentin specimens (4’4’2 mm3 were prepared and randomly assigned to 4 groups (n = 10: SnCl2 (800 ppm/6.7 mM Sn, NaF (250 ppm/13 mM F, NaF/SnCl2 (800 ppm/6.7 mM Sn; 250 ppm/13 mM F, and deionized water (DIW as a negative control. An acquired pellicle was formed on dentin samples by incubation in clarified, pooled, stimulated human saliva for 24 hours. The specimens were subjected to 5 daily cycles, each consisting of 5 of min demineralization (0.3%/15.6 mM citric acid, pH 2.6, 6’/day and 60 min of re-mineralization in clarified human saliva. Thirty minutes after the 1st, 3rd and 5th demineralization episodes of each day, the specimens were treated with one of the test solutions for 2 min. Surface loss was measured via optical profilometry. Mixed-model ANOVA followed by Tukey’s test were used for the statistical analysis. Sn, F, and their combination significantly reduced the dentin surface loss by 23%, 36%, and 60% compared with DIW, respectively. All groups were significantly different (p < 0.05. The combination of Sn and F significantly reduced the amount of dentin surface loss compared with all other groups. The F group also significantly reduced surface loss compared with Sn and DIW, followed by the Sn group, which showed significantly greater protection compared with the DIW control. The daily use of a combined fluoride and stannous solution is promising for preventing dentin erosion.

The Possible Role of Dentin as a Piezoelectric Signal Generator by Determining the Elec-tromechanical Coupling Factor of Dentin

Directory of Open Access Journals (Sweden)

Atabak Shahidi

2011-08-01

Full Text Available Introduction: This article aimed at calculation of the electromechanical coupling factor of dentin which is an indicator of the effectiveness with which a piezoelectric material converts electrical en-ergy into mechanical energy, or vice versa. The hypothesis: The electro-mechanical coupling factor of dentin was determined in mode 11 and 33 by calculating the ratio of the produced electrical energy to the stored elastic energy in dentin under applied pressure. This study showed that the electromechanical coupling factor of dentin was affected by the direction of the applied force and the moisture content of dentin. Also dentin was a weak electromechanical energy converter which might be categorized as a piezoelectric pressure sensor.Evaluation of the hypothesis: Determination of the electrome-chanical coupling factor of dentin and its other piezoelectric constants is essential to investigate the biologic role of piezoelectricity in tooth.

Calibration of a lactic-acid model for simulating biofilm-induced degradation of the dentin-composite interface.

Science.gov (United States)

Zhu, Laikuan; Li, Yuping; Carrera, Carola A; Chen, Yung-Chung; Li, Mingyu; Fok, Alex

2017-11-01

To verify and calibrate a chemical model for simulating the degradation of the dentin-composite interface induced by multi-species oral biofilms in vitro. Dentin-composite disks (5-mm dia.×2-mm thick) were made from bovine incisor roots and filled with either Z100™ (Z100) or Filtek™ LS (LS) composite. The disks, which were covered with nail varnish, but with one of the dentin-composite margins exposed, were immersed in lactic acid solution at pH 4.5 for up to 48h. Diametral compression was performed to measure the reduction in bond strength of the dentin-composite disks following acid challenge. Scanning electron microscopy (SEM) was used to examine decalcification of dentin and fracture modes of the disks. To better understand the degradation process, micro-computed tomography, in combination with a radiopaque dye (AgNO 3 ), was used to assess interfacial leakage in 3D longitudinally, while SEM was used to determine the path of leakage. One-way analysis of variance (ANOVA) was used to analyze the results, with the level of statistical significance set at pcomposite interface, instead. The degree of dentin demineralization, the reduction in debonding load and the modes of failure observed were very similar to those induced by multi-species oral biofilms found in the previous work. Leakage of AgNO 3 occurred mainly along the hybrid layer. The specimens filled with Z100 had a thicker hybrid layer (∼6.5μm), which exhibited more interfacial leakage than those filled with LS. The chemical model with lactic acid used in this study can induce degradation to the dentin-composite interface similar to those produced by multi-species biofilms. With appropriate calibration, this could provide an effective in vitro method for ageing composite restorations in assessing their potential clinical performance. Copyright © 2017 The Academy of Dental Materials. All rights reserved.

Shear bond strength of resin composite bonded with two adhesives: Influence of Er: YAG laser irradiation distance

Science.gov (United States)

Shirani, Farzaneh; Birang, Reza; Malekipour, Mohammad Reza; Hourmehr, Zahra; Kazemi, Shantia

2014-01-01

Background: Dental surfaces prepared with different Er:YAG laser distance may have different characteristics compared with those prepared with conventional instruments. The aim of this study was to investigate the effect of Er:YAG laser irradiation distance from enamel and dentin surfaces on the shear bond strength of composite with self-etch and etch and rinse bonding systems compared with conventional preparation method. Materials and Methods: Two hundred caries-free human third molars were randomly divided into twenty groups (n = 10). Ten groups were designated for enamel surface (E1-E10) and ten for dentin surface (D1-D10). Er: YAG laser (2940 nm) was used on the E1-E8 (240 mJ, 25 Hz) and D1-D8 (140 mJ, 30 Hz) groups at four different distances of 0.5 (standard), 2, 4 and 11 mm. Control groups (E9, E10, D9 and D10) were ground with medium grit diamond bur. The enamel and dentin specimens were divided into two subgroups that were bonded with either Single Bond or Clearfil SE Bond. Resin composite (Z100) was dispensed on prepared dentin and enamel. The shear bond strengths were tested using a universal testing machine. Data were analyzed by SPSS12 statistical software using three way analysis of variance, Tukey and independent t-test. P enamel and dentin substrates (P enamel surfaces (in both bonding agent subgroups) and on dentin surfaces (in the Single Bond subgroup). Conclusion: Laser irradiation decreases shear bond strength. Irradiation distance affects shear bond strength and increasing the distance would decrease the negative effects of laser irradiation. PMID:25540665

Microshear bonding effectiveness of different dentin regions

Directory of Open Access Journals (Sweden)

Anelise F Montagner

2015-01-01

Full Text Available Aim: The aim of this in vitro study was to evaluate the influence of dentin surfaces with different tubule orientation on bond strength of a multimode adhesive system. Materials and Methods: Twenty human molars were selected and prepared in different ways in order to produce different dentin regions. The teeth were randomized (n = 5 according to the application modes of a multimode adhesive system (etch-and-rinse and self-etching and to the dentin region (occlusal and proximal - 1.5 mm depth from dentinoenamel junction. Cylindrical restorations were performed on dentin with a starch tube. The samples remained immersed in distilled water for 24 h and the microshear bond strength (μSBS test was performed. The μSBS values were expressed in MPa and analyzed with ANOVA and Tukey′s test (P < 0.05. Results: There was no significant difference in the bond strength values between the application modes of the adhesive system (P = 0.19; however, the dentin regions (P < 0.05 significantly affected the μSBS. The proximal dentin presented higher bond strength values than occlusal dentin. Conclusion: The dentin surfaces with different tubule orientation influenced the bonding effectiveness of the adhesive system tested.

Effects of Self-Adjusting File, Mtwo, and ProTaper on the root canal wall

NARCIS (Netherlands)

Hin, E.S.; Wu, M.K.; Wesselink, P.R.; Shemesh, H.

2013-01-01

Introduction The purpose of this ex vivo study was to observe the incidence of cracks in root dentin after root canal preparation with hand files, self-adjusting file (SAF), ProTaper, and Mtwo. Methods One hundred extracted mandibular premolars with single canals were randomly selected. Two

Influence of Immediate Dentin Sealing on the Shear Bond Strength of Pressed Ceramic Luted to Dentin with Self-Etch Resin Cement

Directory of Open Access Journals (Sweden)

Robert Dalby

2012-01-01

Full Text Available Objectives. To examine the effect of immediate dentin sealing (IDS, with dentin bonding agents (DBAs applied to freshly cut dentin, on the shear bond strength of etched pressed ceramic luted to dentin with RelyX Unicem (RXU cement. Method. Eighty extracted noncarious third molars were ground flat to expose the occlusal dentin surfaces. The teeth were randomly allocated to five groups (A to E of sixteen teeth each. Groups A to D were allocated a dentin bonding agent (Optibond FL, One Coat Bond, Single Bond, or Go! that was applied to the dentin surface to mimic the clinical procedure of IDS. These specimen groups then had etched glass ceramic discs (Authentic luted to the sealed dentin surface using RXU. Group E (control had etched glass ceramic discs luted to the dentin surface (without a dentin bonding agent using RXU following the manufacturer’s instructions. All specimens were stored for one week in distilled water at room temperature and then shear stressed at a constant cross-head speed of 1 mm per minute until failure. Statistical analysis was performed by ANOVA followed by post hoc Tukey HSD method (0.05 in the SBS between the test groups (A–D or the control (group E. Conclusion. IDS using the dentin bonding agents tested does not statistically (>0.05 affect the shear bond strength of etched pressed ceramic luted to dentin with RXU when compared to the control.

Assessment of three root canal preparation techniques on root canal geometry using micro-computed tomography: In vitro study

Directory of Open Access Journals (Sweden)

Shaikha M Al-Ali

2012-01-01

Full Text Available Aim: To assess the effects of three root canal preparation techniques on canal volume and surface area using three-dimensionally reconstructed root canals in extracted human maxillary molars. Materials and Methods: Thirty extracted Human Maxillary Molars having three separate roots and similar root shape were randomly selected from a pool of extracted teeth for this study and stored in normal saline solution until used. A computed tomography scanner (Philips Brilliance CT 64-slice was used to analyze root canals in extracted maxillary molars. Specimens were scanned before and after canals were prepared using stainless steel K-Files, Ni-Ti rotary ProTaper and rotary SafeSiders instruments. Differences in dentin volume removed, the surface area, the proportion of unchanged area and canal transportation were calculated using specially developed software. Results: Instrumentation of canals increased volume and surface area. Statistical analysis found a statistically significant difference among the 3 groups in total change in volume (P = 0.001 and total change in surface area (P = 0.13. Significant differences were found when testing both groups with group III (SafeSiders. Significant differences in change of volume were noted when grouping was made with respect to canal type (in MB and DB (P < 0.05. Conclusion: The current study used computed tomography, an innovative and non destructive technique, to illustrate changes in canal geometry. Overall, there were few statistically significant differences between the three instrumentation techniques used. SafeSiders stainless steel 40/0.02 instruments exhibit a greater cutting efficiency on dentin than K-Files and ProTaper. CT is a new and valuable tool to study root canal geometry and changes after preparation in great details. Further studies with 3D-techniques are required to fully understand the biomechanical aspects of root canal preparation.

Ex vivo evaluation of three instrumentation techniques on E. faecalis biofilm within oval shaped root canals

Directory of Open Access Journals (Sweden)

Vitor Cesar NAKAMURA

2015-01-01

Full Text Available The objective of the present study was to assess the effectiveness of reciprocating instrumentation in disinfecting oval-shaped root canals infected with Enterococcus faecalis. Forty-five human lower premolars were infected with a culture of E. faecalis (ATCC 29212 for 28 days. Five other teeth that were neither contaminated nor instrumented were used as controls. The 45 specimens were divided into three experimental groups (n = 15 based on the root canal preparation technique used: manual (K-type, Dentsply Maillefer, Ballaigues, Switzerland; rotary (MTwo, VDW GmbH, Munich, Germany; and reciprocating (Reciproc R50, VDW GmbH, Munich, Germany instruments. During chemomechanical preparation, 21 mL of 2.5% NaOCl was used as the irrigating solution. Microbiological sampling was performed before (S1 and immediately after (S2 the chemomechanical preparation using sterilized paper points. Specimens were then cleaved, and 0.02 g of dentine chips was collected from the root thirds to verify the presence of microorganisms in dentinal tubules. All three preparation techniques reduced the number of microorganisms in the root canal lumen and dentine chips from the root thirds, but no significant differences were observed between the three groups (p > 0.05. Reciprocating instrumentation with Reciproc R50 was effective in reducing the number of microorganisms within the root canal system. Although this technique involves the use of only one file to perform the root canal therapy, it is as effective as conventional rotary instrumentation in reducing theE. faecalis biofilm from the root canal system. However, further clinical investigations are warranted in order to ratify these results.

Effect of Nanofiller Addition to an Experimental Dentin Adhesive on Microtensile Bond Strength to Human Dentin

Directory of Open Access Journals (Sweden)

SH. Kasraei

2009-06-01

Full Text Available Objective: The purpose of the study was to evaluate the influence of adding nanofiller particles to a dentin bonding agent on resin-dentin bond strength.Materials and Methods: Fifty-four human intact premolar teeth were divided in to 6 groups of nine. The teeth were ground on occlusal surfaces and polished with 320 and then 600 grit silicon carbide papers. An experimental bonding system based on acetone/alcoholsolvent was provided with filler contents of 0.0, 0.5, 1.0, 2.5, 5.0, and 10.0 weight percent fumed silica nanofiller. After dentin surface etching, rinsing and blot drying, the experimentalbonding agents were applied to dentin surface. A composite resin was, then,bonded to the dentin on the bonding agent. The specimens were thermocycled for 500 cycles and sectioned in stick form. After two week of storage in distilled water, resin-dentin microtensile bond strength of the specimens was measured. Data were analyzed by one way ANOVA and DunnettT3 tests.Results: Bond strength to dentin was significantly affected by the filler level. Minimum and maximum resin-microtensile bond strength was in the experimental bonding agent with no filler (5.88 MPa and with filler level of 1.0 weight percent (15.15 MPa, respectively,and decreased with the increase of filler content down to 8.95 MPa for the filler level of 10.0 weight percent.Conclusion: Filler content seems to be one of the important factors influencing the bond strength of dental adhesives. Maximum dentin bond strength was obtained with 1% silanized nanofiller silica added to experimental adhesive system.

Antimicrobial 2-hydroxyisocaproic acid and chlorhexidine resist inactivation by dentine.

Science.gov (United States)

Sakko, M; Tjäderhane, L; Sorsa, T; Hietala, P; Rautemaa, R

2016-04-01

To compare the antibacterial activity of 2-hydroxyisocaproic acid (HICA) with currently used root canal medicaments and to examine their interactions with potential inhibitors in nutrient-deficient and nutrient-rich conditions. First, the antibacterial activity of single concentrations of HICA, calcium hydroxide solution or slurry, chlorhexidine digluconate or acetate was tested against Enterococcus faecalis with and without potential inhibitors: dentine powder (DP), hydroxyapatite or bovine serum albumin, in a low concentration of peptone water. Relative viable counts were determined by culture at 1, 24 and 48 h. In the second set of experiments, the activity of three concentrations of HICA was evaluated against two isolates of E. faecalis with and without potential inhibitors in nutrient-rich thioglycollate broth using a modification of a standard microdilution method. The minimum bactericidal concentration was determined by culture at 1, 24 and 48 h. Concentrations of ≥33 mg mL(-1) of HICA were found to be bactericidal against E. faecalis in both nutrient-deficient and nutrient-rich environments at 24- to 48-h incubation, whereas the initial activity of Ca(OH)2 slurry was lost at 48-h incubation. HICA tolerated well all tested potential inhibitors up to 19 mg mL(-1) . DP concentrations higher than this inhibited its activity in a dose-dependent manner in both environments. DP demonstrated moderate antibacterial activity, and it enhanced the otherwise limited activity of Ca(OH)2 slurry and solution. DP did not impact on the activity of chlorhexidine. These results support the long-term antibacterial activity of HICA and indicate its tolerance to clinically relevant concentrations of dentine and other inhibitors commonly present in the root canal system. Therefore, HICA may have potential as an interappointment medication in the treatment of root canal infections. © 2015 International Endodontic Journal. Published by John Wiley & Sons Ltd.

Efficacy of Modified Bioactive Glass for Dentin Remineralization and Obstruction of Dentinal Tubules

Directory of Open Access Journals (Sweden)

Mahshid Saffarpour

2017-10-01

Full Text Available Objectives: This study assessed the efficacy of modified bioactive glass (MBG for dentin remineralization and obstruction of dentinal tubules.Materials and Methods: Thirty-six dentin discs were made from 20 third molars and were stored in 12% lactic acid solution for two weeks to induce demineralization. The samples were divided into three groups (n=12: 1- BG, 2- BG modified with 5% strontium (Sr and 3- BG modified with 10% Sr. After applying the BG, the samples were stored in artificial saliva for 7, 14 and 21 days. Attenuated Total Reflection-Fourier Transform Infrared Spectroscopy (ATR-FTIR, X-ray Diffraction (XRD analysis, Scanning Electron Microscopy (SEM, and Energy-Dispersive X-ray (EDX analysis were used to assess remineralization. Also, 6 dentin discs were divided into three groups of BG, BG modified with 5% Sr and BG modified with 10% Sr, to examine tubular occlusion. The discs were etched using 0.5M of EDTA for two minutes and were stored in artificial saliva for 7 days. Changes in dentin surface morphology were evaluated under SEM.Results: Group 3 showed high rates of remineralization at days 7 and 14, although the rate decreased at day 21. Group 2 exhibited high rates of remineralization at days 7, 14 and 21. Dentinal tubules were partially occluded by BG and BG modified with 5% Sr, while they were almost completely obstructed after the use of BG modified with 10% Sr.Conclusions: Strontium increases remineralization. Addition of 10% Sr to BG enhances apatite formation; however, the apatite dissolves over time. Addition of 5% Sr to BG stabilizes the apatite lattice and increases the remineralization.

Effects of endodontic tri-antibiotic paste on bond strengths of dentin adhesives to coronal dentin

Directory of Open Access Journals (Sweden)

Parvin Mirzakoucheki

2015-05-01

Full Text Available Objectives The aim of this study was to evaluate the effects of tri-antibiotic paste (TAP on microtensile bond strengths (MTBS of dental adhesives to dentin. Materials and Methods Sixty extracted molars had their occlusal surfaces flattened to expose dentin. They were divided into two groups, i.e., control group with no dentin treatment and experimental group with dentin treatment with TAP. After 10 days, specimens were bonded using self-etch (Filtek P90 adhesive or etch-and-rinse (Adper Single Bond Plus adhesives and restored with composite resin. Teeth were sectioned into beams, and the specimens were subjected to MTBS test. Data were analyzed using two-way ANOVA and post hoc Tukey tests. Results There was a statistically significant interaction between dentin treatment and adhesive on MTBS to coronal dentin (p = 0.003. Despite a trend towards worse MTBS being noticed in the experimental groups, TAP application showed no significant effect on MTBS (p = 0.064. Conclusions The etch-and-rinse adhesive Adper Single Bond Plus presented higher mean bond strengths than the self-etch adhesive Filtek P90, irrespective of the group. The superior bond performance for Adper Single Bond when compared to Filtek P90 adhesive was confirmed by a fewer number of adhesive failures. The influence of TAP in bond strength is insignificant.

Effect of bur-cut dentin on bond strength using two all-in-one and one two-step adhesive systems.

Science.gov (United States)

Koase, Kaori; Inoue, Satoshi; Noda, Mamoru; Tanaka, Toru; Kawamoto, Chiharu; Takahashi, Akiko; Nakaoki, Yasuko; Sano, Hidehiko

2004-01-01

To compare the microtensile bond strength (MTBS) of two all-in-one adhesive systems and one experimental two-step self-etching adhesive system to two types of bur-cut dentin. Using one of the three adhesives, Xeno CF Bond (Xeno), Prompt L-Pop (PL), or the experimental two-step system ABF (ABF), resin composite was bonded to flat buccal and root dentin surfaces of eight extracted human premolars. These surfaces were produced using either regular-grit or superfine-grit diamond burs. After storage overnight in 37 degrees C water, the bonded specimens were sectioned into six or seven slices approximately 0.7 mm thick perpendicular to the bonded surface. They were then subjected to microtensile testing. The surfaces of the fractured specimens were observed microscopically to determine the failure mode. In addition, to observe the effect of conditioning, the two types of bur-cut dentin surfaces were conditioned with the adhesives, rinsed with acetone, and observed with SEM. When Xeno and PL were bonded to dentin cut with a regular-grit diamond bur, MTBS values were lower than to superfine bur-cut dentin, and failures occurred adhesively at the interface, whereas the experimental two-step adhesive showed no significant difference in microtensile bond strength between two differently cut surfaces. The all-in-one adhesives tested here improved bond strengths when bonded to superfine bur-cut dentin as a substrate, whereas the experimental two-step adhesive system showed unchanged bonding to both regular and superfine bur-cut dentin surfaces.

Effect of adhesive system and application strategy on reduction of dentin permeability

Directory of Open Access Journals (Sweden)

Adriana Oliveira Carvalho

2012-10-01

Full Text Available This study evaluated the effect of adhesive systems and application strategies on dentin hydraulic conductance (HC. The buccal enamel was removed from bovine incisors to simulate laminate cavity preparations. After removing the roots and the coronal pulp, the buccal dentin was treated with EDTA solution (0.5 M for 5 minutes, rinsed, ultrasonicated for 12 minutes and connected to a permeability device. HC of the specimens was measured at 10 psi (n = 5. Permeability was measured before and after bonding procedures using G-Bond (GB, Clearfil Tri-S Bond (CTS, Hybrid Coat (HY, Bond Force (BF, Adper Easy Bond (AEB Silorane (SI, Clearfil SE Bond (CSE and Adper Scotchbond Multi-Purpose (SMP adhesives systems, which were applied following three strategies: 1 according to the manufacturers' instructions; 2 two coats of all-in-one self-etching adhesives (GB, CTS, HY, BF, AEB or priming step plus two coats of bonding resin for the other systems (SI, CSE and SMP; and 3 a thin layer of a flowable composite applied over one coat of all-in-one self-etching adhesives or primed surface for SI, CSE and SMP adhesives. No significant difference was observed among the application modes concerning their ability to reduce HC. None of the adhesives showed complete sealing (100% of the bovine tooth dentin. SI exhibited lower HC than SMP, however, they were not significantly different from the other systems. The results suggest that all systems tested result in an HC reduction of more than 90%. The wet bonding technique seemed to be more sensitive for dentin sealing.

Infra-red and Raman spectroscopic studies of infected and affected dentine

International Nuclear Information System (INIS)

Aminzadeh, A.; Aminzadeh, A.; Khosravy, K.

2002-01-01

Diagnosis of infected and affected dentine is an important factor in clinical restorative treatment of dentine. In this study, the IR and Raman spectra of the sound dentine, infected dentine and affected dentine are reported. The structure of infected dentine and affected dentine has been compared with the sound dentine and hydroxyapatite. It is shown while the infected dentine has lost its structure, the affected dentine has more or less a structure similar to the sound dentine. The molecular structure of collagen remains unchanged in both infected and affected dentine

Influence of CVD diamond tips and Er:YAG laser irradiation on bonding of different adhesive systems to dentin

OpenAIRE

da Silva, Melissa Aline [UNESP; Nicolo, Rebeca Di [UNESP; Barcellos, Daphne Camara [UNESP; Batista, Graziela Ribeiro [UNESP; Pucci, Cesar Rogerio [UNESP; Torres, Carlos Rocha Gomes [UNESP; Borges, Alessandra Bühler [UNESP

2013-01-01

Aim: The aim of this study was to compare the microtensile bond strength of three adhesive systems, using different methods of dentin preparation. Materials and methods: A hundred and eight bovine teeth were used. The dentin from buccal face was exposed and prepared with three different methods, divided in 3 groups: Group 1 (DT)- diamond tip on a high-speed handpiece; Group 2 (CVD)-CVD tip on a ultrasonic handpiece; Group 3 (LA)-Er: YAG laser. The teeth were divided into 3 subgroups, accordin...

Dentin-cement Interfacial Interaction

Science.gov (United States)

Atmeh, A.R.; Chong, E.Z.; Richard, G.; Festy, F.; Watson, T.F.

2012-01-01

The interfacial properties of a new calcium-silicate-based coronal restorative material (Biodentine™) and a glass-ionomer cement (GIC) with dentin have been studied by confocal laser scanning microscopy (CLSM), scanning electron microscopy (SEM), micro-Raman spectroscopy, and two-photon auto-fluorescence and second-harmonic-generation (SHG) imaging. Results indicate the formation of tag-like structures alongside an interfacial layer called the “mineral infiltration zone”, where the alkaline caustic effect of the calcium silicate cement’s hydration products degrades the collagenous component of the interfacial dentin. This degradation leads to the formation of a porous structure which facilitates the permeation of high concentrations of Ca2+, OH-, and CO32- ions, leading to increased mineralization in this region. Comparison of the dentin-restorative interfaces shows that there is a dentin-mineral infiltration with the Biodentine, whereas polyacrylic and tartaric acids and their salts characterize the penetration of the GIC. A new type of interfacial interaction, “the mineral infiltration zone”, is suggested for these calcium-silicate-based cements. PMID:22436906

Shear bond strength of self-etch and total-etch bonding systems at different dentin depths

Directory of Open Access Journals (Sweden)

Ana Carolina Maito Villela-Rosa

2011-04-01

Full Text Available The purpose of this study was to evaluate the dentin shear bond strength of four adhesive systems (Adper Single Bond 2, Adper Prompt L-Pop, Magic Bond DE and Self Etch Bond in regards to buccal and lingual surfaces and dentin depth. Forty extracted third molars had roots removed and crowns bisected in the mesiodistal direction. The buccal and lingual surfaces were fixed in a PVC/acrylic resin ring and were divided into buccal and lingual groups assigned to each selected adhesive. The same specimens prepared for the evaluation of superficial dentin shear resistance were used to evaluate the different depths of dentin. The specimens were identified and abraded at depths of 0.5, 1.0, 1.5 and 2.0 mm. Each depth was evaluated by ISO TR 11405 using an EMIC-2000 machine regulated at 0.5 mm/min with a 200 Kgf load cell. We performed statistical analyses on the results (ANOVA, Tukey and Scheffé tests. Data revealed statistical differences (p < 0.01 in the adhesive and depth variation as well as adhesive/depth interactions. The Adper Single Bond 2 demonstrated the highest mean values of shear bond strength. The Prompt L-Pop product, a self-etching adhesive, revealed higher mean values compared with Magic Bond DE and Self Etch Bond adhesives, a total and self-etching adhesive respectively. It may be concluded that the shear bond strength of dentin is dependent on material (adhesive system, substrate depth and adhesive/depth interaction.

Root canal morphology of primary molars: a micro-computed tomography study.

Science.gov (United States)

Fumes, A C; Sousa-Neto, M D; Leoni, G B; Versiani, M A; da Silva, L A B; da Silva, R A B; Consolaro, A

2014-10-01

This was to investigate the root canal morphology of primary molar teeth using micro-computed tomography. Primary maxillary (n = 20) and mandibular (n = 20) molars were scanned at a resolution of 16.7 μm and analysed regarding the number, location, volume, area, structured model index (SMI), area, roundness, diameters, and length of canals, as well as the thickness of dentine in the apical third. Data were statistically compared by using paired-sample t test, independent sample t test, and one-way analysis of variance with significance level set as 5%. Overall, no statistical differences were found between the canals with respect to length, SMI, dentine thickness, area, roundness, and diameter (p > 0.05). A double canal system was observed in the mesial and mesio-buccal roots of the mandibular and maxillary molars, respectively. The thickness in the internal aspect of the roots was lower than in the external aspect. Cross-sectional evaluation of the roots in the apical third showed flat-shaped canals in the mandibular molars and ribbon- and oval-shaped canals in the maxillary molars. External and internal anatomy of the primary first molars closely resemble the primary second molars. The reported data may help clinicians to obtain a thorough understanding of the morphological variations of root canals in primary molars to overcome problems related to shaping and cleaning procedures, allowing appropriate management strategies for root canal treatment.

Histological observation on dental hard tissue irradiated by ultrashort-pulsed laser

Science.gov (United States)

Uchizono, Takeyuki; Awazu, Kunio; Igarashi, Akihiro; Kato, Junji; Hirai, Yoshito

2006-04-01

In the field of dentistry, effectiveness of USPL irradiation is researched because USPL has less thermal side effect to dental hard tissue. In this paper, we observed morphological change and optical change of dental hard tissue irradiated by USPL for discussing the safety and effectiveness of USPL irradiation to dental hard tissues. Irradiated samples were crown enamel and root dentin of bovine teeth. Lasers were Ti:sapphire laser, which had pulse duration (P d)of 130 fsec and pulse repetition rate (f) of 1kHz and wavelength (l) of 800nm, free electron laser (FEL), which had P d of 15 μsec and f of 10Hz and wavelength of 9.6μm, and Er:YAG laser, which had P d of 250 μsec and f of 10Hz and wavelength of 2.94μm. After laser irradiation, the sample surfaces and cross sections were examined with SEM and EDX. The optical change of samples was observed using FTIR. In SEM, the samples irradiated by USPL had sharp and accurate ablation with no crack and no carbonization. But, in FEL and Er:YAG laser, the samples has rough ablation with crack and carbonization. It was cleared that the P/Ca ratio of samples irradiated by USPL had same value as non-irradiated samples. There was no change in the IR absorption spectrum between samples irradiated by USPL and non-irradiated sample. But, they of samples irradiated by FEL and Er:YAG laser, however, had difference value as non-irradiated samples. These results showed that USPL might be effective to ablate dental hard tissue without thermal damage.

Root length in the permanent teeth of women with an additional X chromosome (47,XXX females).

Science.gov (United States)

Lähdesmäki, Raija E; Alvesalo, Lassi J

2010-07-01

Previous studies have demonstrated differential effects of the X and Y chromosomes on dental development. The expression of sexual dimorphism in terms of tooth size, shape, number and developmental timing has been explained especially by Y chromosome influence. The Y chromosome promotes enamel, crown and root dentin development. The X chromosome has an effect on enamel deposition. The aim of this research is to study the influence of the extra X chromosome on the development of permanent tooth root length. The study subjects (all of whom were from the Kvantti Dental Research Project) were seven 47,XXX females, five female relatives and 51 and 52 population control men and women, respectively. Measurements were made from panoramic radiographs on available permanent teeth by a digital calliper according to established procedures. The results showed that the maxillary root lengths of the 47,XXX females were of the same magnitude as those in normal women, but the mandibular root lengths were longer in 47,XXX females than in normal men or women. Increased enamel thickness in the teeth of 47,XXX females is apparently caused by the active enamel gene in all X chromosomes having no increased influence on crown dentin formation. These results in 47,XXX females indicate an increase in root dentin development, at least in the mandible, which together with the data on crown formation reflects a continuous long-lasting effect of the X chromosome on dental development.

Effect of Instrumentation Techniques, Irrigant Solutions and Artificial accelerated Aging on Fiberglass Post Bond Strength to Intraradicular Dentin.

Science.gov (United States)

Santana, Fernanda Ribeiro; Soares, Carlos José; Silva, Júlio Almeida; Alencar, Ana Helena Gonçalves; Renovato, Sara Rodrigues; Lopes, Lawrence Gonzaga; Estrela, Carlos

2015-07-01

To evaluate the effect of instrumentation techniques, irrigant solutions and specimen aging on fiberglass posts bond strength to intraradicular dentine. A total of 120 bovine teeth were prepared and randomized into control and experimental groups resulting from three study factors (instrumentation techniques, irrigant solutions, specimen aging). Posts were cemented with RelyX U100. Samples were submitted to push-out test and failure mode was evaluated under a confocal microscope. In specimens submitted to water artificial aging, nickel-titanium rotary instruments group presented higher bond strength values in apical third irrigated with NaOCl or chlorhexi-dine. Irrigation with NaOCl resulted in higher bond strength than ozonated water. Artificial aging resulted in significant bond strength increase. Adhesive cement-dentin failure was prevalent in all the groups. Root canal preparation with NiTi instruments associated with NaOCl irrigation and ethylenediaminetetra acetic acid (EDTA) increased bond strength of fiberglass posts cemented with self-adhesive resin cement to intraradicular dentine. Water artificial aging significantly increased post-Clinical significance: The understanding of factors that may influence the optimal bond between post-cement and cement-dentin are essential to the success of endodontically treated tooth restoration.

The relationship between carbohydrate content and gamma irradiation during rooting of chrysanthemum cuttings

International Nuclear Information System (INIS)

Noh, Seol Ah; Kim, Jin Kyu

2003-01-01

The effect of gamma radiation on carbohydrate metabolism was studied in chrysanthemum cuttings. Total water-soluble carbohydrate, glucose, fructose, sucrose, and starch contents were measured in leaves and stems. Differences in the accumulation of carbohydrate associated with inhibition or stimulation in response to gamma irradiation. Sucrose levels increased significantly in leaves and stems until the 15th day, reaching maximum values on that day. Glucose contents declined rapidly until the 10th day and increased later, reaching maximum values on the 15th day. Fructose levels gradually increased, reaching maximum values at the 10th day, and then decreased again. Differences in the components of soluble carbohydrates were evident between rooting durations and doses. Soluble sugars were in the highest contents in the 20 Gy irradiated group. However, irradiation dose higher than 20 Gy resulted in an inhibitory effect

Antibacterial efficacy of Mangifera indica L. kernel and Ocimum sanctum L. leaves against Enterococcus faecalis dentinal biofilm

Science.gov (United States)

Subbiya, Arunajatesan; Mahalakshmi, Krishnan; Pushpangadan, Sivan; Padmavathy, Kesavaram; Vivekanandan, Paramasivam; Sukumaran, Vridhachalam Ganapathy

2013-01-01

Introduction: The Enterococcus faecalis biofilm in the root canal makes it difficult to be eradicated by the conventional irrigants with no toxicity to the tissues. Hence, plant products with least side effects are explored for their use as irrigants in the root canal therapy. Aim: To evaluate and compare the antibacterial efficacy of Mangifera indica L. kernel (mango kernel) and Ocimum sanctum L. leaves (tulsi) extracts with conventional irrigants (5% sodium hypochlorite (NaOCl) and 2% chlorhexidine) against E. faecalis dentinal biofilm. Materials and Methods: Agar diffusion and broth microdilution assay was performed with the herbal extracts and conventional irrigants (2% chlorhexidine and 5% NaOCl) against E. faecalis planktonic cells. The assay was extended onto 3 week E. faecalis dentinal biofilm. Results: Significant reduction of colony forming units (CFU)/mL was observed for the herbal groups and the antibacterial activity of the herbal groups was at par with 5% NaOCl. Conclusions: The antibacterial activity of these herbal extracts is found to be comparable with that of conventional irrigants both on the biofilm and planktonic counterparts. PMID:24082577

Effect of tumor therapeutic irradiation on the mechanical properties of teeth tissue

International Nuclear Information System (INIS)

Fraenzel, W.; Gerlach, R.; Hein, H.J.; Schaller, H.G.

2006-01-01

Tumor irradiation of the head-neck area is accompanied by the development of a so-called radiation caries in the treated patients. In spite of conservative therapeutic measures, the process results in tooth destruction. The present study investigated the effects of irradiation on the demineralization and remineralization of the dental tissue. For this purpose, retained third molars were prepared and assigned either to a test group, which was exposed to fractional irradiation up to 60 Gy, or to a non-irradiated control group. Irradiated and non-irradiated teeth were then demineralized using acidic hydroxyl-cellulose gel; afterwards the teeth were remineralized using either Bifluorid12 registered or elmex gelee registered . The nanoindentation technique was used to measure the mechanical properties, hardness and elasticity, of the teeth in each of the conditions. The values were compared to the non-irradiated control group. Irradiation decreased dramatically the mechanical parameters of enamel and dentine. In non-irradiated teeth, demineralization had nearly the same effects of irradiation on the mechanical properties. In irradiated teeth, the effects of demineralization were negligible in comparison to non-irradiated teeth. Remineralization with Bifluorid12 registered or elmex gelee registered led to a partial improvement of the mechanical properties of the teeth. The enamel was more positively affected, by remineralization than the dentine. (orig.)

[Bond strengths of absorbable polylactic acid root canal post with three different adhesives].

Science.gov (United States)

Pan, Hui; Cheng, Can; Hu, Jia; Liu, He; Sun, Zhi-hui

2015-12-18

To find absorbable adhesives with suitable bonding properties for the absorbable polylactic acid root canal post. To test and compare the bond strengths of absorbable polylactic acid root canal post with three different adhesives. The absorbable polylactic acid root canal posts were used to restore the extracted teeth, using 3 different adhesives: cyanoacrylates, fibrin sealant and glass ionomer cement. The teeth were prepared into slices for micro-push-out test. The bond strength was statistically analyzed using ANOVA. The specimens were examined using microscope and the failure mode was divided into four categories: cohesive failure between absorbable polylactic acid root canal posts and adhesives, cohesive failure between dentin and adhesives, failure within the adhesives and failure within the absorbable polylactic acid root canal posts. The bond strength of cyanoacrylates [(16.83 ± 6.97) MPa] and glass ionomer cement [(12.10 ± 5.09) MPa] were significantly higher than fibrin sealant [(1.17 ± 0.50) MPa], Padhesives was 25.0%, the cohesive failure between the dentin and the adhesives was 16.7%, the failure within the adhesives was 33.3%, and the failure within the absorbable polylactic acid root canal posts was 25.0%. In the group of fibrin sealant, the cohesive failure between the absorbable polylactic acid root canal posts and the adhesives was 66.7%, the cohesive failure between the dentin and the adhesives was 22.2%, the failure within the adhesives was 11.1%. In the group of glass ionomer cement, the cohesive failure between the absorbable polylactic acid root canal posts and the adhesives was 87.5%, the failure within the adhesives was 12.5%. The major failure mode in fibrin sealant and glass ionomer cement was the cohesive failure between the absorbable polylactic acid root canal posts and the adhesives. No major failure modes were found in the group of cyanoacrylates. The bond strength of fibrin sealant is low, which cannot meet the requirement of

Analysis of root surface properties by fluorescence/Raman intensity ratio.

Science.gov (United States)

Nakamura, Shino; Ando, Masahiro; Hamaguchi, Hiro-O; Yamamoto, Matsuo

2017-11-01

The aim of this study is to evaluate the existence of residual calculus on root surfaces by determining the fluorescence/Raman intensity ratio. Thirty-two extracted human teeth, partially covered with calculus on the root surface, were evaluated by using a portable Raman spectrophotometer, and a 785-nm, 100-mW laser was applied for fluorescence/Raman excitation. The collected spectra were normalized to the hydroxyapatite Raman band intensity at 960 cm -1 . Raman spectra were recorded from the same point after changing the focal distance of the laser and the target radiating angle. In seven teeth, the condition of calculus, cementum, and dentin were evaluated. In 25 teeth, we determined the fluorescence/Raman intensity ratio following three strokes of debridement. Raman spectra collected from the dentin, cementum, and calculus were different. After normalization, spectra values were constant. The fluorescence/Raman intensity ratio of calculus region showed significant differences compared to the cementum and dentin (p Raman intensity ratio decreased with calculus debridement. For this analysis, the delta value was defined as the difference between the values before and after three strokes, with the final 2 delta values close to zero, indicating a gradual asymptotic curve and the change in intensity ratio approximating that of individual constants. Fluorescence/Raman intensity ratio was effectively used to cancel the angle- and distance-dependent fluctuations of fluorescence collection efficiency during measurement. Changes in the fluorescence/Raman intensity ratio near zero suggested that cementum or dentin was exposed, and calculus removed.

Irradiation seed treatment reduces scald, common root rot and increases phosphorus absorption of barley

International Nuclear Information System (INIS)

Arabi, M.I.E.; Jawhar, M.

2003-01-01

The effect of low doses of gamma irradiation on severity of barley to scald and common root rot diseases, and phosphorus absorption was studied seeds were exposed to doses of 0, 10, 15, 20, 30, 40 and 50 Gy. A stimulatory effect was observed at irradiation doses of 30 and 40 Gy, which decreased the severity of barley to scald by 34% and 31% respectively. On the other hand, doses 20 and 30 Gy decreased the severity to CRR by 54% and 49% respectively, whereas, phosphorus absorption was significantly increased at doses of 15 and 20 Gy

Bacteroides gingivalis antigens and bone resorbing activity in root surface fractions of periodontally involved teeth

International Nuclear Information System (INIS)

Patters, M.R.; Landsberg, R.L.; Johansson, L.-A.; Trummel, C.L.; Robertson, P.R.

1982-01-01

Bone resorbing activity and the presence of antigens of Bacteroides gingivalis were assessed in plaque, calculus, cementum, and dentin obtained from roots of teeth previously exposed to periodontitis. Each fraction was obtained by scaling the root surface. The fraction were extracted by stirring and sonication, and the soluble centrifuged, sterilized, dialyzed, and adjusted to equivalent protein concentrations. Cementum and dentin extracts from impacted teeth were prepared similarly and served as controls. Stimulation of bone resorption by each extract was assessed in organ cultures of fetal rat bones by measurement of release of previously-incorporated 45 Ca from the bone into the medium. In some groups of teeth, calculus and cementum were treated with acid prior to scaling. Citric acid washes were recovered and dialyzed. An enzyme-linked immunosorbent assay (ELISA) was used to assess the extracts for the presence of antigens reactive with an antiserum to B. gingivalis. Significant stimulation of bone resorption was found in all calculus and periodontally-involved cementum preparations. ELISA showed significant levels of B.gingivalis antigens in plaque, calculus, and cementum of periodontally-involved teeth, but not in involved dentin nor in cementum or dentin of impact teeth. Treatment with citric acid removed essentially all B.gingivalis antigens from cementum but not calculus. The results suggest that substances which stimulate bone resorption and substances which react with B. gingivalis antiserum are present in surface plaque, calculus, and cementum or periodontally-involved teeth. These substances are not present in cementum and dentin of impacted teeth nor in dentin of periodontally-involved teeth. Treatment by both scaling and citric demineralization will remove most of these substances from cementum of teeth previously exposed to periodontitis. (author)

Bacteroides gingivalis antigens and bone resorbing activity in root surface fractions of periodontally involved teeth

Energy Technology Data Exchange (ETDEWEB)

Patters, M R; Landsberg, R L; Johansson, L A; Trummel, C L; Robertson, P R [Department of Periodontology, University of Connecticut, School of Dental Medicine, Farmington, Connecticut, U.S.A.

1982-01-01

Bone resorbing activity and the presence of antigens of Bacteroides gingivalis were assessed in plaque, calculus, cementum, and dentin obtained from roots of teeth previously exposed to periodontitis. Each fraction was obtained by scaling the root surface. The fraction were extracted by stirring and sonication, and the soluble centrifuged, sterilized, dialyzed, and adjusted to equivalent protein concentrations. Cementum and dentin extracts from impacted teeth were prepared similarly and served as controls. Stimulation of bone resorption by each extract was assessed in organ cultures of fetal rat bones by measurement of release of previously-incorporated /sup 45/Ca from the bone into the medium. In some groups of teeth, calculus and cementum were treated with acid prior to scaling. Citric acid washes were recovered and dialyzed. An enzyme-linked immunosorbent assay (ELISA) was used to assess the extracts for the presence of antigens reactive with an antiserum to B. gingivalis. Significant stimulation of bone resorption was found in all calculus and periodontally-involved cementum preparations. ELISA showed significant levels of B.gingivalis antigens in plaque, calculus, and cementum of periodontally-involved teeth, but not in involved dentin nor in cementum or dentin of impact teeth. Treatment with citric acid removed essentially all B.gingivalis antigens from cementum but not calculus. The results suggest that substances which stimulate bone resorption and substances which react with B. gingivalis antiserum are present in surface plaque, calculus, and cementum or periodontally-involved teeth. These substances are not present in cementum and dentin of impacted teeth nor in dentin of periodontally-involved teeth. Treatment by both scaling and citric demineralization will remove most of these substances from cementum of teeth previously exposed to periodontitis.

Cervical shaping in curved root canals: comparison of the efficiency of two endodontic instruments

OpenAIRE

Busquim Sandra Soares Kühne; Santos Marcelo dos

2002-01-01

The aim of this study was to determine the removal of dentin produced by number 25 (0.08) Flare files (Quantec Flare Series, Analytic Endodontics, Glendora, California, USA) and number 1 e 2 Gates-Glidden burs (Dentsply - Maillefer, Ballaigues, Switzerland), in the mesio-buccal and mesio-lingual root canals, respectively, of extracted human permanent inferior molars, by means of measuring the width of dentinal walls prior and after instrumentation. The obtained values were compared. Due to th...

Pulp-dentin Regeneration: Current State and Future Prospects.

Science.gov (United States)

Cao, Y; Song, M; Kim, E; Shon, W; Chugal, N; Bogen, G; Lin, L; Kim, R H; Park, N-H; Kang, M K

2015-11-01

The goal of regenerative endodontics is to reinstate normal pulp function in necrotic and infected teeth that would result in reestablishment of protective functions, including innate pulp immunity, pulp repair through mineralization, and pulp sensibility. In the unique microenvironment of the dental pulp, the triad of tissue engineering would require infection control, biomaterials, and stem cells. Although revascularization is successful in resolving apical periodontitis, multiple studies suggest that it alone does not support pulp-dentin regeneration. More recently, cell-based approaches in endodontic regeneration based on pulpal mesenchymal stem cells (MSCs) have demonstrated promising results in terms of pulp-dentin regeneration in vivo through autologous transplantation. Although pulpal regeneration requires the cell-based approach, several challenges in clinical translation must be overcome-including aging-associated phenotypic changes in pulpal MSCs, availability of tissue sources, and safety and regulation involved with expansion of MSCs in laboratories. Allotransplantation of MSCs may alleviate some of these obstacles, although the long-term stability of MSCs and efficacy in pulp-dentin regeneration demand further investigation. For an alternative source of MSCs, our laboratory developed induced MSCs (iMSCs) from primary human keratinocytes through epithelial-mesenchymal transition by modulating the epithelial plasticity genes. Initially, we showed that overexpression of ΔNp63α, a major isoform of the p63 gene, led to epithelial-mesenchymal transition and acquisition of stem characteristics. More recently, iMSCs were generated by transient knockdown of all p63 isoforms through siRNA, further simplifying the protocol and resolving the potential safety issues of viral vectors. These cells may be useful for patients who lack tissue sources for endogenous MSCs. Further research will elucidate the level of potency of these iMSCs and assess their

Dentin and pulp sense cold stimulus.

Science.gov (United States)

Tokuda, Masayuki; Tatsuyama, Shoko; Fujisawa, Mari; Morimoto-Yamashita, Yoko; Kawakami, Yoshiko; Shibukawa, Yoshiyuki; Torii, Mistuso

2015-05-01

Dentin hypersensitivity is a common symptom, and recent convergent evidences have reported transient receptor potential (TRP) channels in odontoblasts act as mechanical and thermal molecular sensor, which detect stimulation applied on the exposed dentin surface, to drive multiple odontoblastic cellular functions, such as sensory transduction and/or dentin formation. In the present study, we confirmed expression of TRP melastatin subfamily member-8 (TRPM8) channels in primary cultured cells derived from human dental pulp cells (HPCs) and mouse odontoblast-lineage cells (OLCs) as well as in dentin matrix protein-1 (DMP-1) and dentin sialoprotein (DSP) positive acutely isolated rat odontoblasts from dental pulp tissue slice culture by immunohistochemical analyses. In addition, we detected TRPM8 channel expression on HPCs and OLCs by RT-PCR and Western blotting analyses. These results indicated that both odontoblasts and dental pulp cells express TRPM8 channels in rat, mouse and human, and therefore we hypothesize they may contribute as cold sensor in tooth. Copyright © 2015 Elsevier Ltd. All rights reserved.

Evaluation of the Self-Adjusting File system (SAF) for the instrumentation of primary molar root canals: a micro-computed tomographic study.

Science.gov (United States)

Kaya, E; Elbay, M; Yiğit, D

2017-06-01

The Self-Adjusting File (SAF) system has been recommended for use in permanent teeth since it offers more conservative and effective root-canal preparation when compared to traditional rotary systems. However, no study had evaluated the usage of SAF in primary teeth. The aim of this study was to evaluate and compare the use of SAF, K file (manual instrumentation) and Profile (traditional rotary instrumentation) systems for primary-tooth root-canal preparation in terms of instrumentation time and amounts of dentin removed using micro-computed tomography (μCT) technology. Study Design: The study was conducted with 60 human primary mandibular second molar teeth divided into 3 groups according to instrumentation technique: Group I: SAF (n=20); Group II: K file (n=20); Group III; Profile (n=20). Teeth were embedded in acrylic blocks and scanned with a μCT scanner prior to instrumentation. All distal root canals were prepared up to size 30 for K file,.04/30 for Profile and 2 mm thickness, size 25 for SAF; instrumentation time was recorded for each tooth, and a second μCT scan was performed after instrumentation was complete. Amounts of dentin removed were measured using the three-dimensional images by calculating the difference in root-canal volume before and after preparation. Data was statistically analysed using the Kolmogorov-Smirnov and Kruskal-Wallis tests. Manual instrumentation (K file) resulted in significantly more dentin removal when compared to rotary instrumentation (Profile and SAF), while the SAF system generated significantly less dentin removal than both manual instrumentation (K file) and traditional rotary instrumentation (Profile) (psystems. Within the experimental conditions of the present study, the SAF seems as a useful system for root-canal instrumentation in primary molars because it removed less dentin than other systems, which is especially important for the relatively thin-walled canals of primary teeth, and because it involves less

Femtosecond laser ablation of dentin

International Nuclear Information System (INIS)

Alves, S; Vilar, R; Oliveira, V

2012-01-01

The surface morphology, structure and composition of human dentin treated with a femtosecond infrared laser (pulse duration 500 fs, wavelength 1030 nm, fluences ranging from 1 to 3 J cm -2 ) was studied by scanning electron microscopy, x-ray diffraction, x-ray photoelectron spectroscopy and Fourier transform infrared spectroscopy. The average dentin ablation threshold under these conditions was 0.6 ± 0.2 J cm -2 and the ablation rate achieved in the range 1 to 2 µm/pulse for an average fluence of 3 J cm -2 . The ablation surfaces present an irregular and rugged appearance, with no significant traces of melting, deformation, cracking or carbonization. The smear layer was entirely removed by the laser treatment. For fluences only slightly higher than the ablation threshold the morphology of the laser-treated surfaces was very similar to the dentin fracture surfaces and the dentinal tubules remained open. For higher fluences, the surface was more porous and the dentin structure was partially concealed by ablation debris and a few resolidified droplets. Independently on the laser processing parameters and laser processing method used no sub-superficial cracking was observed. The dentin constitution and chemical composition was not significantly modified by the laser treatment in the processing parameter range used. In particular, the organic matter is not preferentially removed from the surface and no traces of high temperature phosphates, such as the β-tricalcium phosphate, were observed. The achieved results are compatible with an electrostatic ablation mechanism. In conclusion, the high beam quality and short pulse duration of the ultrafast laser used should allow the accurate preparation of cavities, with negligible damage of the underlying material. (paper)

Comparison of different retreatment techniques and root canal sealers: a scanning electron microscopic study

Directory of Open Access Journals (Sweden)

Neslihan Simsek

2014-05-01

Full Text Available The aim of this study was to evaluate the effectiveness of two retreatment techniques, in terms of the operating time and scanning electron microscopy (SEM results, in removing three different root canal sealers from root canals that were previously filled with gutta-percha. Sixty extracted single-rooted human premolars were divided into three groups and filled with iRoot SP, MM Seal, and AH Plus sealers, along with gutta-percha, through a lateral compaction technique. Root canal fillings of the samples were removed by ESI ultrasonic tips or R-Endo files. The time to reach the working length was recorded. Longitudinally sectioned samples were examined under SEM magnification. Each picture was evaluated in terms of the residual debris. Data were statistically analyzed with the Kruskall-Wallis test. No statistically significant differences were found in terms of operating time (p>0.05. Significant differences in the number of debris-free dentinal tubules were found among the root canal thirds, but this finding was not influenced by the experimental group (p < 0.05. Resin sealer tags were observed inside the dentinal tubules in the MM Seal group. Under the conditions of this study, it may be established that there was no difference among the sealers and retreatment techniques.

Comparative study of analgesic effect of the infrared low-intensity laser and 33% sodium fluoride paste in the treatment of dentinal hypersensitivity

International Nuclear Information System (INIS)

Oliveira, Glen Anderson Maia de

2003-01-01

Different desensitizing agents have been used in the treatment of dentinal hypersensitivity, however, some presented treatments are still frustrating. The purpose of this study was to evaluate the analgesic effect of the low-intensity GaAlAs laser (λ= 830 nm) in the treatment of dentinal hypersensitivity after mechanical and thermal stimuli, and compared it with the 33% sodium fluoride paste. Thirty two teeth with dentinal hypersensitivity were selected and randomly divided into two groups. For the laser group, each tooth was irradiated by a dose of 6 J/cm 2 during two minutes and half on the buccal side. The paste group was treated with a NaF/kaolin/glycerin (33:33:33) paste by burnishing the sensitive surface during four minutes. The sensitivity degree was measured before the beginning of the experiment, 24 h, 48 h, 72 h, 120 h, 15 days and 30 days after the first application. The results indicate that the dentinal hypersensitivity significantly diminished for the paste group after dental explorer. Regarding to air-blast, no significant differences were observed between the groups. Both of them were effective in reducing pain of the dentine hypersensitive after 120 h. (author)

Influence of refreshment/activation cycles and temperature rise on the reaction rate of sodium hypochlorite with bovine dentine during ultrasonic activated irrigation.

Science.gov (United States)

Macedo, R G; Verhaagen, B; Wesselink, P R; Versluis, M; van der Sluis, L W M

2014-02-01

To evaluate the effect of multiple refreshment/activation cycles and temperature on the reaction rate of sodium hypochlorite (NaOCl) with bovine dentine during ultrasonic activated irrigation (UAI) under laboratory conditions. The root canal walls of 24 standardized root canals in bovine incisors were exposed to a standardized volume of NaOCl at different temperatures (24 °C and 38 °C) and exposure times (20, 60 and 180 s). The irrigant was refreshed and ultrasonically activated four times for 20 s followed by a 40 s rest interval, with no refreshment and no activation as the controls. The reaction rate was determined by measuring the amount of active chlorine in the NaOCl solution before and after being exposed to dentine during the specific experimental conditions. Calorimetry was used to measure the electrical-to-sonochemical conversion efficiency during ultrasonic activation. Refreshment, activation and exposure time all increased the reaction rate of NaOCl (P reaction rate of NaOCl (P > 0.125). The reaction rate of NaOCl with dentine is enhanced by refreshment, ultrasonic activation and exposure time. Temperature rise of irrigant during ultrasonic activation was not sufficient to alter the reaction rate. © 2013 International Endodontic Journal. Published by John Wiley & Sons Ltd.

Photoacoustic imaging of teeth for dentine imaging and enamel characterization

Science.gov (United States)

Periyasamy, Vijitha; Rangaraj, Mani; Pramanik, Manojit

2018-02-01

Early detection of dental caries, cracks and lesions is needed to prevent complicated root canal treatment and tooth extraction procedures. Resolution of clinically used x-ray imaging is low, hence optical imaging techniques such as optical coherence tomography, fluorescence imaging, and Raman imaging are widely experimented for imaging dental structures. Photoacoustic effect is used in photon induced photoacoustic streaming technique to debride the root canal. In this study, the extracted teeth were imaged using photoacoustic tomography system at 1064 nm. The degradation of enamel and dentine is an indicator of onset of dental caries. Photoacoustic microscopy (PAM) was used to study the tooth enamel. Images were acquired using acoustic resolution PAM system. This was done to identify microscopic cracks and dental lesion at different anatomical sites (crown and cementum). The PAM tooth profile is an indicator of calcium distribution which is essential for demineralization studies.

"Dentinal microcracks after root canal preparation" a comparative evaluation with hand, rotary and reciprocating instrumentation.

Science.gov (United States)

Priya, N Tulasi; Chandrasekhar, Veeramachaneni; Anita, S; Tummala, Muralidhar; Raj, T B Phanindhar; Badami, Vijetha; Kumar, Pradeep; Soujanya, E

2014-12-01

The purpose of this study was to compare the incidence of dentinal micro cracks after instrumentation with various types of NiTi files in rotary and reciprocating motion. One hundred human extracted mandibular central incisors were taken and divided into 10 groups (n=10 teeth per group). Group 1- No preparation, Group 2 - Hand instrumentation, Groups 3,4 - ProTaper files in rotary and reciprocating motion, Groups 5,6 - ProTaper Next files in rotary and reciprocating motion, Groups 7,8 - Oneshape files in rotary and reciprocating motion, Groups 9,10 - Reciproc files in rotary and reciprocating motion. Specimens were sectioned horizontally at 3,6 and 9 mm from the apex and dentinal micro cracks were observed under a stereomicroscope. There was a statistically significant difference between the groups (pProtaper Next - Rot, Protaper Next - Rec, Reciproc - Rec); (ProTaper - Rot, ProTaper - Rec, Oneshape - Rot), (Oneshape - Rot, Reciproc - Rot), (One shape Reciproc, Reciproc - Rec); (p >.05). Least cracks were seen in canals instrumented with Pro Taper Next files both in rotary and reciprocating motion. Full sequence rotary systems showed less cracks than single file systems and full sequence rotary systems showed less cracks in reciprocating motion than in rotary motion.

Morphologic analysis, by means of scanning electron microscopy, of the effect of Er: YAG laser on root surfaces submitted to scaling and root planing Análise morfológica, através de microscopia eletrônica de varredura, da ação do laser de Er: YAG em superfícies radiculares submetidas à raspagem e aplainamento radicular

Directory of Open Access Journals (Sweden)

Letícia Helena Theodoro

2002-12-01

Full Text Available The purpose of this study was to morphologically evaluate, by means of scanning electron microscopy, the effects of Er:YAG laser on the treatment of root surfaces submitted to scaling and root planing with conventional periodontal instruments. Eighteen root surfaces (n = 18, which had been previously scaled and planed, were assigned to 3 groups (n = 6. The control Group (G1 received no further treatment; Group 2 (G2 was irradiated with Er:YAG laser (2.94 mum, with 47 mJ/10 Hz, in a focused mode with air/water spray during 15 s and with 0.57 J/cm² of fluency per pulse; Group 3 (G 3 was irradiated with Er:YAG laser (2.94 mum, with 83 mJ/10 Hz, in a focused mode with air/water spray during 15 s and with 1.03 J/cm² of fluency per pulse. We concluded that the parameters adopted for Group 3 removed the smear layer from the root surface, exposing the dentinal tubules. Although no fissures, cracks or carbonized areas were observed, an irregular surface was produced by Er:YAG laser irradiation. Thus, the biocompatibility of the irradiated root surface, within the periodontal healing process, must be assessed.O objetivo do presente estudo foi analisar morfologicamente, através de microscopia eletrônica de varredura, os efeitos do laser de Er:YAG no tratamento de superfícies radiculares submetidas à raspagem e aplainamento radicular com instrumentos manuais. Foram utilizados 18 espécimes (n = 18 de superfícies radiculares que após ser submetidos à raspagem e aplainamento radicular foram divididos em 3 grupos (n = 6. O grupo controle (G1 não sofreu nenhum tratamento; Grupo 2 (G2 foi irradiado com laser de Er:YAG (2,94 mim 47 mJ/10 Hz, focalizado,com refrigeração à água durante 15 s e fluência de pulso de 0,57 J/cm²; Grupo 3 (G3 foi irradiado com laser de Er:YAG (2,94 mim, 83 mJ/10 Hz, focalizado, com refrigeração à agua durante 15 s e fluência de pulso de 1,03 J/cm². Através da análise dos resultados podemos concluir que o laser de

Dentinal tubules revealed with X-ray tensor tomography.

Science.gov (United States)

Jud, Christoph; Schaff, Florian; Zanette, Irene; Wolf, Johannes; Fehringer, Andreas; Pfeiffer, Franz

2016-09-01

Dentin is a mineralized material making up most of the tooth bulk. A system of microtubules, so called dentinal tubules, transverses it radially from the pulp chamber to the outside. This highly oriented structure leads to anisotropic mechanical properties directly connected to the tubules orientation and density: the ultimate tensile strength as well as the fracture toughness and the shear strength are largest perpendicular to dentinal tubules. Consequently, the fatigue strength depends on the direction of dentinal tubules, too. However, none of the existing techniques used to investigate teeth provide access to orientation and density of dentinal tubules for an entire specimen in a non-destructive way. In this paper, we measure a third molar human tooth both with conventional micro-CT and X-ray tensor tomography (XTT). While the achievable resolution in micro-CT is too low to directly resolve the dentinal tubules, we provide strong evidence that the direction and density of dentinal tubules can be indirectly measured by XTT, which exploits small-angle X-ray scattering to retrieve a 3D map of scattering tensors. We show that the mean directions of scattering structures correlate to the orientation of dentinal tubules and that the mean effective scattering strength provides an estimation of the relative density of dentinal tubules. Thus, this method could be applied to investigate the connection between tubule orientation and fatigue or tensile properties of teeth for a full sample without cutting one, non-representative peace of tooth out of the full sample. Copyright © 2016 The Academy of Dental Materials. All rights reserved.

Antimicrobial Effect of Citrus Aurantifolia Extract on Enterococcus Faecalis Within the Dentinal Tubules in The Presence of Smear Layer

Directory of Open Access Journals (Sweden)

Sharifian MR

2011-12-01

Full Text Available Background and Aims: Instrumentation of the root canals results in formation of smear layer which covers the dentinal tubules. In infected teeth, it is ideal to achieve a material that has the ability to remove the smear layer besides antimicrobial activity. Therefore, this study was designed to evaluate the antimicrobial effect of Citrus aurantifolia extracts (lime juice and rind extract on Enterococcus faecalis within dentinal tubules in the presence of smear layer.Materials and Methods: One-hundred and forty dentin tubes were prepared from bovine incisors. After removal the smear layer, the specimens were infected with Enterococcus faecalis. Then, the smear layer was reformed. Test solutions were used as the irrigants in study roups as follows: group 1: 5.25% NaOCl; group 2: 17% EDTA; group 3: NaOCl+EDTA; group 4: Lime juice; group 5: ethanolic rind extract of C.aurantifolia; group 6: 96% ethanol. Dentin chips were collected from inner and outer layers of dentinal walls and optical density was measured. The data were analyzed using one-way ANOVA and Tamhane tests.Results: In outer layer of dentin, the efficacy of rind extract was less than that of NaOCl+EDTA (P<0.05. Also Lime juice was less effective than EDTA, NaOCl and NaOCl+EDTA (P<0.05. In inner layer of dentin, Lime juice was significantly less effective than NaOCl and NaOCl+EDTA (P<0.05. The efficacy of rind extract was less than that of NaOCl+EDTA (P<0.05.Conclusion: In the presence of smear layer, the antimicrobial activity of Lime juice was less than that of NaOCl but the efficacy of rind extract was similar to that of NaOCl.

Effect of tumor therapeutic irradiation on the mechanical properties of teeth tissue

Energy Technology Data Exchange (ETDEWEB)

Fraenzel, W. [Dept. of Physics, Martin Luther Univ. Halle (Germany); Gerlach, R. [Univ. Clinic and Policlinic for Radiation Therapy, Martin Luther Univ. Halle (Germany); Hein, H.J. [Univ. Clinic and Policlinic for Orthopaedics and Physical Medicine, Martin Luther Univ. Halle (Germany); Schaller, H.G. [Dept. of Operative Dentistry and Periodontology, Martin Luther Univ. Halle (Germany)

2006-07-01

Tumor irradiation of the head-neck area is accompanied by the development of a so-called radiation caries in the treated patients. In spite of conservative therapeutic measures, the process results in tooth destruction. The present study investigated the effects of irradiation on the demineralization and remineralization of the dental tissue. For this purpose, retained third molars were prepared and assigned either to a test group, which was exposed to fractional irradiation up to 60 Gy, or to a non-irradiated control group. Irradiated and non-irradiated teeth were then demineralized using acidic hydroxyl-cellulose gel; afterwards the teeth were remineralized using either Bifluorid12 {sup registered} or elmex gelee {sup registered}. The nanoindentation technique was used to measure the mechanical properties, hardness and elasticity, of the teeth in each of the conditions. The values were compared to the non-irradiated control group. Irradiation decreased dramatically the mechanical parameters of enamel and dentine. In non-irradiated teeth, demineralization had nearly the same effects of irradiation on the mechanical properties. In irradiated teeth, the effects of demineralization were negligible in comparison to non-irradiated teeth. Remineralization with Bifluorid12 {sup registered} or elmex gelee {sup registered} led to a partial improvement of the mechanical properties of the teeth. The enamel was more positively affected, by remineralization than the dentine. (orig.)

Dietary adaptions in the ultrastructure of dinosaur dentine.

Science.gov (United States)

Brink, Kirstin S; Chen, Yu-Cheng; Wu, Ya-Na; Liu, Wei-Min; Shieh, Dar-Bin; Huang, Timothy D; Sun, Chi-Kuang; Reisz, Robert R

2016-12-01

Teeth are key to understanding the feeding ecology of both extant and extinct vertebrates. Recent studies have highlighted the previously unrecognized complexity of dinosaur dentitions and how specific tooth tissues and tooth shapes differ between taxa with different diets. However, it is unknown how the ultrastructure of these tooth tissues contributes to the differences in feeding style between taxa. In this study, we use third harmonic generation microscopy and scanning electron microscopy to examine the ultrastructure of the dentine in herbivorous and carnivorous dinosaurs to understand how the structure of this tissue contributes to the overall utility of the tooth. Morphometric analyses of dentinal tubule diameter, density and branching rates reveal a strong signal for dietary preferences, with herbivorous saurischian and ornithischian dinosaurs consistently having higher dentinal tubule density than their carnivorous relatives. We hypothesize that this relates to the hardness of the dentine, where herbivorous taxa have dentine that is more resistant to breakage and wear at the dentine-enamel junction than carnivorous taxa. This study advocates the detailed study of dentine and the use of advanced microscopy techniques to understand the evolution of dentition and feeding ecology in extinct vertebrates. © 2016 The Author(s).

Effect of dentin bonding agent diffusing through dentin slices on the reactive oxygen species production and apoptosis of pulpal cells

Directory of Open Access Journals (Sweden)

Bor-Shiunn Lee

2015-04-01

Conclusion: The three DBAs after diffusion through 0.2- or 0.5-mm dentin slice still exhibit cytotoxicity to dental pulp cells. However, the 0.5-mm dentin slice is found to be a better barrier than the 0.2-mm dentin slice to protect dental pulp cells from DBA-induced cytotoxicity.

Dentin Permeability of Carious Primary Teeth

African Journals Online (AJOL)

primary dental pulp make it difficult to determine which modality offers the best ... The most common pathology of the dentine is dental caries. ... to evaluate dentine permeability is to calculate its hydraulic conductance (Lp) using fluid filtration ...

Effect of dentin biomodifiers on the immediate and long-term bond strengths of a simplified etch and rinse adhesive to dentin.

Science.gov (United States)

Singh, Payal; Nagpal, Rajni; Singh, Udai Pratap

2017-08-01

This in vitro study evaluated the effect of dentin biomodifiers on the immediate and long-term bond strengths of a simplified etch and rinse adhesive to dentin. Flat coronal dentin surfaces were prepared in 120 extracted human molars. Teeth were randomly divided into 5 groups ( n = 24) according to 5 different surface pre-treatments: No pre-treatment (control); 1M carbodiimide (EDC); 0.1% epigallocatechin-3-gallate (EGCG); 2% minocycline (MI); 10% sodium ascorbate (SA). After surface pre-treatment, adhesive (Adper Single Bond 2 [SB], 3M ESPE) was applied. Composite was applied into transparent plastic tubes (2.5 mm in diameter), which was placed over the bonded dentin surface. From each group, 10 samples were subjected to shear bond strength (SBS) evaluation at 24 hours (immediate) and remaining 10 samples were tested after 6 months (delayed). Additionally, 4 samples per group were subjected to scanning electron microscopic analysis for observation of resin-dentin interface. The data were statistically analysed with Shaperio‑Wilk W test, 2-way analysis of variance (ANOVA), and post hoc Tukey's test. At 24 hours, SBS of all surface pre-treatment groups were comparable with the control group, with significant differences found between EDC and SA groups only ( p = 0.009). After 6 months storage, EDC, EGCG, and MI pre-treatments preserved the resin-dentin bond strength with no significant fall. Dentin pre-treatment with all the dentin biomodifiers except SA resulted in significant preservation of resin-dentin bond over 6 months storage period, without negatively affecting the immediate bond strength of the etch and rinse adhesive tested.

Machinability of some dentin simulating materials.

Science.gov (United States)

Möllersten, L

1985-01-01

Machinability in low speed drilling was investigated for pure aluminium, Frasaco teeth, ivory, plexiglass and human dentin. The investigation was performed in order to find a suitable test material for drilling experiments using paralleling instruments. A material simulating human dentin in terms of cuttability at low drilling speeds was sought. Tests were performed using a specially designed apparatus. Holes to a depth of 2 mm were drilled with a twist drill using a constant feeding force. The time required was registered. The machinability of the materials tested was determined by direct comparison of the drilling times. As regards cuttability, first aluminium and then ivory were found to resemble human dentin most closely. By comparing drilling time variances the homogeneity of the materials tested was estimated. Aluminium, Frasaco teeth and plexiglass demonstrated better homogeneity than ivory and human dentin.

Effects of low-intensity GaAlAs laser radiation (λ=660 nm) on dentine-pulp interface after class I cavity preparation

International Nuclear Information System (INIS)

Godoy, Bruno Miranda

2003-01-01

The aim of this study was to investigate the effects of low-intensity irradiation with GaAlAs laser (red emission) on the ultrastructure of dentine-pulp interface after conventionally prepared class I cavity preparation. Two patients with 8 premolars for extraction indicated for orthodontic reasons. Class I cavities were prepared in these teeth that were then divided into two groups. The first group received a treatment with laser with continuous emission, λ=660 nm, with maximum power output of 30 mW. The dosimetry applied was of approximately 2J/cm 2 , directly and perpendicularly into the cavity in only one section. After the irradiation, the cavities were filled with composite resin. The second group received the same treatment, except by the laser therapy. Twenty-eight days after the preparation, the teeth were extracted and were processed for transmission electron microscopy analysis. Two sound teeth, without any preparation, were also studied. The irradiated group presented odontoblastic processes in higher contact with the extracellular matrix and the collagen fibers appeared more aggregated and organized than those of control group. These results were also observed in the healthy-teeth. Thus, we suggest that laser irradiation accelerates the recovery of the dental structures involved in the cavity preparation at the pre-dentine level. (author)

Raman spectra of human dentin mineral

NARCIS (Netherlands)

Tsuda, H; Ruben, J; Arends, J

Human dentin mineral has been investigated by using micro-Raman spectroscopy. Fluorescence and thermal problems were largely avoided by preparing dentin samples by grinding and ultrasonic agitation in acetone. The Raman spectral features were consistent with those of impure hydroxyapatite containing

Biodentine-a novel dentinal substitute for single visit apexification

Directory of Open Access Journals (Sweden)

Gurudutt Nayak

2014-05-01

Full Text Available Use of an apical plug in management of cases with open apices has gained popularity in recent years. Biodentine, a new calcium silicate-based material has recently been introduced as a dentine substitute, whenever original dentine is damaged. This case report describes single visit apexification in a maxillary central incisor with necrotic pulp and open apex using Biodentine as an apical barrier, and a synthetic collagen material as an internal matrix. Following canal cleaning and shaping, calcium hydroxide was placed as an intracanal medicament for 1 mon. This was followed by placement of small piece of absorbable collagen membrane beyond the root apex to serve as matrix. An apical plug of Biodentine of 5 mm thickness was placed against the matrix using pre-fitted hand pluggers. The remainder of canal was back-filled with thermoplasticized gutta-percha and access cavity was restored with composite resin followed by all-ceramic crown. One year follow-up revealed restored aesthetics and function, absence of clinical signs and symptoms, resolution of periapical rarefaction, and a thin layer of calcific tissue formed apical to the Biodentine barrier. The positive clinical outcome in this case is encouraging for the use of Biodentine as an apical plug in single visit apexification procedures.

Resistance to compression of weakened roots subjected to different root reconstruction protocols

Directory of Open Access Journals (Sweden)

Lucas Villaça Zogheib

2011-12-01

Full Text Available OBJECTIVE: This study evaluated, in vitro, the fracture resistance of human non-vital teeth restored with different reconstruction protocols. MATERIAL AND METHODS: Forty human anterior roots of similar shape and dimensions were assigned to four groups (n=10, according to the root reconstruction protocol: Group I (control: non-weakened roots with glass fiber post; Group II: roots with composite resin by incremental technique and glass fiber post; Group III: roots with accessory glass fiber posts and glass fiber post; and Group IV: roots with anatomic glass fiber post technique. Following post cementation and core reconstruction, the roots were embedded in chemically activated acrylic resin and submitted to fracture resistance testing, with a compressive load at an angle of 45º in relation to the long axis of the root at a speed of 0.5 mm/min until fracture. All data were statistically analyzed with bilateral Dunnett's test (α=0.05. RESULTS: Group I presented higher mean values of fracture resistance when compared with the three experimental groups, which, in turn, presented similar resistance to fracture among each other. None of the techniques of root reconstruction with intraradicular posts improved root strength, and the incremental technique was suggested as being the most recommendable, since the type of fracture that occurred allowed the remaining dental structure to be repaired. CONCLUSION: The results of this in vitro study suggest that the healthy remaining radicular dentin is more important to increase fracture resistance than the root reconstruction protocol.

Effectiveness of EDTA as the irrigation solution to remove smear layer in root canal

Directory of Open Access Journals (Sweden)

Kurniasri Amas Achiar

2009-07-01

Full Text Available One of the objectives of successful endodontic treatment is the hermetic obturation of the root canal system. To achieve this, the root canal filling must seal the canal space both apically and coronally to prevent the ingress of microorganisms or tissue fluids into the canal space. Apical leakage is reported a common reason for the clinical failure of endodontic therapy. Leakage through an obturated root canal is expected to take place at interfaces between sealer and dentin or sealer and gutta-percha, or through voids within the sealer. Hence, the sealing quality of root canal filling depends much on the sealing ability of the sealer. Therefore, anything that may influence the adaptation of the root filling to the canal wall is can determine the degree and the extent of leakage, and ultimately the prognosis of the endodontic therapy. In endodontic therapy, the smear layer formation results from root canal preparation and may influence the effective seal of the root canal system. The smear layer formation is mainly composed of inorganic components (dentin debris and organic materials, such as pulp tissue remnant, bacteria, and blood cells. Removal of the smear layer from the root canal walls before the obturation can reduce the leakage of root canal sealer. To remove the smear layer use 10 ml 17% EDTA followed by 10 ml of 5.25% NaOCl as irrigating solution. This paper discribe about how the effectivity of EDTA as irigating solution to remove the smear layer especially in the apical root canal with many lateral canal to reduce the apical leakage.

Effect of dentin biomodifiers on the immediate and long-term bond strengths of a simplified etch and rinse adhesive to dentin

Directory of Open Access Journals (Sweden)

Payal Singh

2017-07-01

Full Text Available Objectives This in vitro study evaluated the effect of dentin biomodifiers on the immediate and long-term bond strengths of a simplified etch and rinse adhesive to dentin. Materials and Methods Flat coronal dentin surfaces were prepared in 120 extracted human molars. Teeth were randomly divided into 5 groups (n = 24 according to 5 different surface pre-treatments: No pre-treatment (control; 1M carbodiimide (EDC; 0.1% epigallocatechin-3-gallate (EGCG; 2% minocycline (MI; 10% sodium ascorbate (SA. After surface pre-treatment, adhesive (Adper Single Bond 2 [SB], 3M ESPE was applied. Composite was applied into transparent plastic tubes (2.5 mm in diameter, which was placed over the bonded dentin surface. From each group, 10 samples were subjected to shear bond strength (SBS evaluation at 24 hours (immediate and remaining 10 samples were tested after 6 months (delayed. Additionally, 4 samples per group were subjected to scanning electron microscopic analysis for observation of resin-dentin interface. The data were statistically analysed with Shaperio‑Wilk W test, 2-way analysis of variance (ANOVA, and post hoc Tukey's test. Results At 24 hours, SBS of all surface pre-treatment groups were comparable with the control group, with significant differences found between EDC and SA groups only (p = 0.009. After 6 months storage, EDC, EGCG, and MI pre-treatments preserved the resin-dentin bond strength with no significant fall. Conclusions Dentin pre-treatment with all the dentin biomodifiers except SA resulted in significant preservation of resin-dentin bond over 6 months storage period, without negatively affecting the immediate bond strength of the etch and rinse adhesive tested.

Selective treatment of carious dentin using a mid-infrared tunable pulsed laser at 6 μm wavelength range

Science.gov (United States)

Saiki, Masayuki; Ishii, Katsunori; Yoshikawa, Kazushi; Yasuo, Kenzo; Yamamoto, Kazuyo; Awazu, Kunio

2011-03-01

Optical technologies have good potential for caries detection, prevention, excavation, and the realization of minimal intervention dentistry. This study aimed to develop a selective excavation technique of carious tissue using the specific absorption in 6 μm wavelength range. Bovine dentin demineralized with lactic acid solution was used as a carious dentin model. A mid-infrared tunable pulsed laser was obtained by difference-frequency generation technique. The wavelength was tuned to 6.02 and 6.42 μm which correspond to absorption bands called amide I and amide II, respectively. The laser delivers 5 ns pulse width at a repetition rate of 10 Hz. The morphological change after irradiation was observed with a scanning electron microscope, and the measurement of ablation depth was performed with a confocal laser microscope. At λ = 6.02 μm and the average power density of 15 W/cm2, demineralized dentin was removed selectively with less-invasive effect on sound dentin. The wavelength of 6.42 μm also showed the possibility of selective removal. High ablation efficiency and low thermal side effect were observed using the nanosecond pulsed laser with λ = 6.02 μm. In the near future, development of compact laser device will open the minimal invasive laser treatment to the dental clinic.

New perspectives about molecular arrangement of primary and permanent dentin

Energy Technology Data Exchange (ETDEWEB)

Sanches Borges, Ana Flavia [Department of Dental Materials at Piracicaba Dental School, State University of Campinas, Piracicaba, SP (Brazil); Andrade Bitar, Renata [Biomedical Engineering, Valley of Paraiba University (UNIVAP) (Brazil); Kantovitz, Kamila Rosamilia [Department of Pediatric Dentistry at Piracicaba Dental School, State University of Campinas, Piracicaba, SP (Brazil); Bortollazo Correr, Americo [Department of Dental Materials at Piracicaba Dental School, State University of Campinas, Piracicaba, SP (Brazil); Martin, Airton Abrahao [Biomedical Engineering Post Graduation, Valley of Paraiba University (UNIVAP) (Brazil); Puppin-Rontani, Regina Maria [Department of Pediatric Dentistry at Piracicaba Dental School, State University of Campinas, Piracicaba, SP (Brazil)], E-mail: rmpuppin@fop.unicamp.br

2007-12-30

The dentin quality of primary and permanent teeth was inspected by Fourier transformed Raman spectroscopy (FT-Raman); scanning electron microscopy/energy-dispersive spectroscopy (SEM/EDS) and hardness test. Middle dentin of crowns were reached by carbide bur abrading providing a uniform smear layer. Phosphoric acid was applied in order to simulate the etching of total etching adhesive systems. The groups were (n = 10): G1 (primary dentin smear layer); G2 (35% phosphoric acid etched primary dentin); G3 (permanent dentin smear layer); G4 (35% phosphoric acid etched permanent dentin). FT-Raman results were subjected to cluster analysis. SEM/EDS were made in order to add the data obtained by FT-Raman. The hardness data were subjected to ANOVA and Tukey test. FT-Raman showed differences among groups, either to organic or inorganic content. For the organic content, primary and permanent dentin became similar after the etching; conversely, the inorganic content showed differences for the two substrates. Hardness test showed no significant differences between primary and permanent dentin, before or after etching, but the etching decreased these values. The mineral content arrangement of primary dentin is different from permanent dentin, independently of the etching. The substrate type did no influence the hardness, but the etching decreased it.

Laser dentistry: A new application of excimer laser in root canal therapy

International Nuclear Information System (INIS)

Pini, R.; Salimbeni, R.; Vannini, M.; Barone, R.; Clauser, C.

1989-01-01

We report the first study of the application of excimer lasers in dentistry for the treatment of dental root canals. High-energy ultraviolet (UV) radiation emitted by an XeCl excimer laser (308 nm) and delivered through suitable optical fibers can be used to remove residual organic tissue from the canals. To this aim, UV ablation thresholds of dental tissues have been measured, showing a preferential etching of infiltrated dentin in respect to healthy dentin, at laser fluences of 0.5-1.5 J/cm 2 . This technique has been tested on extracted tooth samples, simulating a clinical procedure. Fibers of decreasing core diameters have been used to treat different sections of the root canal down to its apical portion, resulting in an effective, easy, and fast cleaning action. Possible advantages of excimer laser clinical applications in respect to usual procedures are also discussed

Effects of fluoride and epigallocatechin gallate on soft-drink-induced dental erosion of enamel and root dentin

Directory of Open Access Journals (Sweden)

Yin-Lin Wang

2018-04-01

Full Text Available Background/Purpose: Fluoride and epigallocatechin gallate (EGCG have been proven to prevent dental caries. The purpose of this study was to evaluate the effects of fluoride and EGCG on soft-drink-induced dental erosion in vitro. Methods: Forty enamel and dentin specimens were prepared from extracted human teeth. The specimens were divided into 4 groups and treated separately with distilled water (as control, 0.5 M sodium fluoride (NF, 400 μM EGCG (EG, and a solution containing 0.5 M NaF and 400 μM EGCG (FG. Cyclic erosive treatment was performed according to the experimental procedures. The specimens were analyzed using laser scanning confocal microscopy, scanning electron microscopy, and a microhardness tester. The data were analyzed using ANOVA and Bonferroni's post hoc test. The significance level was set at 5%. Results: The amount of substance loss was lower in the NF and EG groups than in the control group (p < 0.05. The erosion-caused substance loss was more pronounced in the dentin than in the enamel specimens. Surface microhardness loss was lower in the NF and EG groups than in the control group (p < 0.05. The diameter of the dentinal tubule was wider in the control group than in the NF and EG groups (p < 0.05. No combined effects were observed in the FG group. Conclusion: Both fluoride and EGCG are effective in preventing soft-drink-induced erosion compared with the control group. Fluoride and EGCG may interfere with each other. The mechanisms of the anti-erosive effect need to be explored in the future. Keywords: Dental erosion, Fluoride, Epigallocatechin gallate, Soft drinks, Laser scanning confocal microscopy

Pulpal blood flow recorded from exposed dentine with a laser Doppler flow meter using red or infrared light.

Science.gov (United States)

Kijsamanmith, Kanittha; Vongsavan, Noppakun; Matthews, Bruce

2018-03-01

To determine the percentage of the blood flow signal that is derived from dental pulp when recording from exposed dentine in a human premolar. Recordings were made from 7 healthy teeth in 5 subjects (aged 22-33 yr.) with a laser Doppler flow meter (Periflux 4001) using either a red (635 nm) or an infrared (780 nm) laser. After exposing dentine above the buccal pulpal horn (cavity diam. 1.6 mm, depth 3 mm) and isolating the crown with opaque rubber dam, blood flow was recorded alternately with infrared or red light from the exposed dentine under four conditions: before and after injecting local anaesthetic (3% Mepivacaine without vasoconstrictor) (LA) over the apex of the root of the tooth; after exposing the pulp by cutting a buccal, class V cavity in the tooth; and after sectioning the coronal pulp transversely through the exposure. There was no significant change in mean blood flow recorded with either light source when the tooth was anaesthetized or when the pulp was exposed. After the pulp had been sectioned, the blood flow recorded with infrared light fell by 67.8% and with red light, by 68.4%. The difference between these effects was not significant. When recording blood flow from exposed coronal dentine with either infrared or red light in a tooth isolated with opaque rubber dam, about 68% to the signal was contributed by the pulp. The signal:noise ratio was better with infrared than red light, and when recording from dentine than enamel. Copyright © 2017 Elsevier Ltd. All rights reserved.

Use of poly (amidoamine dendrimer for dentinal tubule occlusion: a preliminary study.

Directory of Open Access Journals (Sweden)

Tianda Wang

Full Text Available The occlusion of dentinal tubules is an effective method to alleviate the symptoms caused by dentin hypersensitivity, a significant health problem in dentistry and daily life. The in situ mineralization within dentinal tubules is a promising treatment for dentin hypersensitivity as it induces the formation of mineral on the sensitive regions and occludes the dentinal tubules. This study was carried out to evaluate the in vitro effect of a whole generation poly(amidoamine (PAMAM dendrimer (G3.0 on dentinal tubule occlusion by inducing mineralization within dentinal tubules. Dentin discs were treated with PAMAM dendrimers using two methods, followed by the in vitro characterization using Attenuated total reflection Fourier-transform infrared spectroscopy (ATR-FTIR, X-ray diffraction (XRD, Field emission scanning electron microscopy (FE-SEM and Energy-Dispersive X-ray Spectroscopy (EDS. These results showed that G3.0 PAMAM dendrimers coated on dentin surface and infiltrated in dentinal tubules could induce hydroxyapatite formation and resulted in effective dentinal tubule occlusion. Moreover, crosslinked PAMAM dendrimers could induce the remineralization of demineralized dentin and thus had the potential in dentinal tubule occlusion. In this in vitro study, dentinal tubules occlusion could be achieved by using PAMAM dendrimers. This could lead to the development of a new therapeutic technique for the treatment of dentin hypersensitivity.

Bonding stability of adhesive systems to eroded dentin

Directory of Open Access Journals (Sweden)

Janaina Barros CRUZ

2015-01-01

Full Text Available This in vitro study evaluated the immediate and 6 months microshear bond strength (µSBS of different adhesive systems to sound and eroded dentin. Sixty bovine incisors were embedded in acrylic resin and ground to obtain flat buccal dentin surfaces. Specimens were randomly allocated into two groups: sound dentin (immersion in artificial saliva and eroded dentin (erosive challenge following a pH cycling model comprising 4 ×/day Sprite Light® drink for 10 days. Then, specimens were reassigned according to the adhesive system: etch-and-rinse adhesive (Adper Single Bond, two-step self-etch system (Clearfil SE Bond, or one-step self-etch adhesive (Adper Easy One. Polyethylene tubes with an internal diameter of 0.76 mm were placed over pre-treated dentin and filled with resin composite (Z250. Half of the specimens were evaluated by the µSBS test after 24 h, and the other half 6 months later, after water storage at 37°C. Failure mode was evaluated using a stereomicroscope (400×. Data were analyzed by three-way repeated measures analysis of variance and Tukey’s post hoc tests (α = 0.05. After 6 months of water aging, marked reductions in µSBS values were observed, irrespective of the substrate. The µSBS values for eroded dentin were lower than those obtained for sound dentin. No difference in bonding effectiveness was observed among adhesive systems. For all groups, adhesive/mixed failure was observed. In conclusion, eroded dentin compromises the bonding quality of adhesive systems over time.

Spectroscopic and thermal characterization of bovine enamel and dentine using the photoacoustic effect

International Nuclear Information System (INIS)

Stolf, Sandro Fernando

2003-01-01

The optical and thermal properties of dental tissues determine the nature and extent of the tissue response through the processes of absorption, transmission, reflection and scattering of the laser light and the heat produced by the absorption of that light. The spectroscopic characterization of bovine dentine and enamel, and the determination of the thermal diffusivity were the aim of this study. The photoacoustic spectra from these tissues were obtained in the Near-Infrared range 900 - 2500 nm, which is the clinical range for odontological application of most lasers. Photoacoustic spectra were taken from block, slices and powder of enamel and dentine. Also photoacoustic spectra were registered before and after 2, 5 and 10 h of topical fluoride (2.26%) application. Using the same technique spectra were taken from dentine and enamel after irradiation with Nd:YAG, Er:YAG, Ho:YLF and CO 2 . It is evident from the results that the presence of O-H in the composition of hydroxyapatite and the water present in the teeth tissue make the obtention of spectrum from components other than O-H bond a very difficult task. In this way, only bands assigned to overtones and combinations of O-H stretch were observed. The thermal diffusivity of the bovine dentine was also measured using the photoacoustic technique. The thermal diffusivity is the physical quantity which measures the rate of heat diffusion throughout the sample. For higher values of the thermal diffusivity the heat diffusion and temperature rise will be faster. As there is many studies devoted to the processes of heat transfer throughout dental tissues using bovine teeth, it is important the determination of its thermal diffusivity. The measured value was found to be a = 2.0 (±0.1).1O -3 cm 2 /s for the both direction, perpendicular and parallel to the dentinal tubules. These a lues indicate that there is no difference between the thermal diffusivities for the both directions. (author)

Effectiveness of EDTA as the irrigation solution to remove smear layer in root canal

OpenAIRE

Kurniasri Amas Achiar; Endang Sukartini

2009-01-01

One of the objectives of successful endodontic treatment is the hermetic obturation of the root canal system. To achieve this, the root canal filling must seal the canal space both apically and coronally to prevent the ingress of microorganisms or tissue fluids into the canal space. Apical leakage is reported a common reason for the clinical failure of endodontic therapy. Leakage through an obturated root canal is expected to take place at interfaces between sealer and dentin or sealer and gu...

Evaluation of Different Dentin Bonding Agents Accompanied with Composite Coronal Barrier

Directory of Open Access Journals (Sweden)

Zahed Mohammadi

2015-06-01

Full Text Available Introduction: The purpose of this study was to evaluate the sealing ability of dentin bonding agents in root canals obturated with gutta-percha and MTA. Methods: Forty-five single rooted human premolar teeth were decoronated so that remaining root portions were 12 mm in length. The samples were divided randomly into three experimental (n=13 and two control groups (n=3. All teeth were instrumented up to #40 K-file using step-back technique. The roots were obturated with gutta-percha/AH26 and MTA for 5 and 3 mm, respectively. Excite, Clearfil SE Bond, and iBond were applied for experimental groups and then 2mm was filled with composite Filtek Z250. The roots in the controls were merely instrumented and obturated. Two coats of nail varnish were applied on the surface of the teeth in the experimental and positive groups, except 2 mm around the apical foramen and coronal surfaces. In the negative control, the surfaces were completely covered by two layers of nail varnish. After thermocycling, the roots mounted in plastic caps of tubes containing BHI medium and inoculated coronally with Enterococcus faecalis. The data were statistically analyzed using Fisher's exact and Kaplan-Meier survival Analysis. Results: There were no statistically significant differences between three experimental groups regarding the leakage rate (P=0.738. Conclusion: Within the limitations of this study, it was observed that the adhesive systems in alliance with gutta-percha and MTA obturation could not entirely

Effect of desensitizing agents on dentin permeability.

Science.gov (United States)

Ishihata, Hiroshi; Kanehira, Masafumi; Nagai, Tomoko; Finger, Werner J; Shimauchi, Hidetoshi; Komatsu, Masashi

2009-06-01

To investigate the in vitro efficacy of two dentin desensitizing products at reducing liquid permeability through human dentin discs. The tested hypothesis was that the products, in spite of different chemical mechanisms were not different at reducing or eliminating flow through dentin discs. Dentin slices (1 mm thick) were prepared from 16 extracted human third molars and their permeability was indirectly recorded in a split chamber model, using a chemiluminescence technique, after EDTA treatment (control), after soaking with albumin, and after desensitizer application. Two products were studied: MS Coat, a self-curing resin-containing oxalate product, and Gluma Desensitizer, a glutaraldehyde/HEMA-based agent without initiator. The dentin slices were mounted between an upper chamber, filled with an aqueous solution of 1% potassium ferricyanide and 0.3% hydrogen peroxide, and a lower chamber filled with 1% sodium hydroxide solution and 0.02% luminol. The upper solution was pressurized, and upon contact with the luminol solution a photochemical signal was generated and recorded as a measure of permeability throughout two consecutive pressurizing cycles at 2.5 and 13 kPa (26 and 133 cm H2O), respectively. The permeability of the control and albumin-soaked samples was similarly high. After application of the desensitizing agents, dentin permeability was reduced to virtually zero at both pressure levels (P < 0.001).

Periodontal ligament stem/progenitor cells with protein-releasing scaffolds for cementum formation and integration on dentin surface.

Science.gov (United States)

Cho, Hankyu; Tarafder, Solaiman; Fogge, Michael; Kao, Kristy; Lee, Chang H

2016-11-01

Purpose/Aim: Cementogenesis is a critical step in periodontal tissue regeneration given the essential role of cementum in anchoring teeth to the alveolar bone. This study is designed to achieve integrated cementum formation on the root surfaces of human teeth using growth factor-releasing scaffolds with periodontal ligament stem/progenitor cells (PDLSCs). Human PDLSCs were sorted by CD146 expression, and characterized using CFU-F assay and induced multi-lineage differentiation. Polycaprolactone scaffolds were fabricated using 3D printing, embedded with poly(lactic-co-glycolic acids) (PLGA) microspheres encapsulating connective tissue growth factor (CTGF), bone morphogenetic protein-2 (BMP-2), or bone morphogenetic protein-7 (BMP-7). After removing cementum on human tooth roots, PDLSC-seeded scaffolds were placed on the exposed dentin surface. After 6-week culture with cementogenic/osteogenic medium, cementum formation and integration were evaluated by histomorphometric analysis, immunofluorescence, and qRT-PCR. Periodontal ligament (PDL) cells sorted by CD146 and single-cell clones show a superior clonogenecity and multipotency as compared with heterogeneous populations. After 6 weeks, all the growth factor-delivered groups showed resurfacing of dentin with a newly formed cementum-like layer as compared with control. BMP-2 and BMP-7 showed de novo formation of tissue layers significantly thicker than all the other groups, whereas CTGF and BMP-7 resulted in significantly improved integration on the dentin surface. The de novo mineralized tissue layer seen in BMP-7-treated samples expressed cementum matrix protein 1 (CEMP1). Consistently, BMP-7 showed a significant increase in CEMP1 mRNA expression. Our findings represent important progress in stem cell-based cementum regeneration as an essential part of periodontium regeneration.

Bond strength of resin modified glass ionomer cement to primary dentin after cutting with different bur types and dentin conditioning

Directory of Open Access Journals (Sweden)

Rebeca Di Nicoló

2007-10-01

Full Text Available The aim of this in vitro study was to evaluate the effect of different bur types and acid etching protocols on the shear bond strength (SBS of a resin modified glass ionomer cement (RM-GIC to primary dentin. Forty-eight clinically sound human primary molars were selected and randomly assigned to four groups (n=12. In G1, the lingual surface of the teeth was cut with a carbide bur until a 2.0-mm-diameter dentin area was exposed, followed by the application of RM-GIC (Vitremer - 3M/ESPE prepared according to the manufacturer's instructions. The specimens of G2, received the same treatment of G1, however the dentin was conditioned with phosphoric acid. In groups G3 and G4 the same procedures of G1 and G2 were conducted respectively, nevertheless dentin cutting was made with a diamond bur. The specimens were stored in distilled water at 37ºC for 24h, and then tested in a universal testing machine. SBS. data were submitted to 2-way ANOVA (= 5% and indicated that SBS values of RM-GIC bonded to primary dentin cut with different burs were not statistically different, but the specimens that were conditioned with phosphoric acid presented SBS values significantly higher that those without conditioning. To observe micromorphologic characteristics of the effects of dentin surface cut by diamond or carbide rotary instruments and conditioners treatment, some specimens were examined by scanning electron microscopy. Smear layer was present in all specimens regardless of the type of rotary instrument used for dentin cutting, and specimens etched with phosphoric acid presented more effective removal of smear layer. It was concluded that SBS of a RM-GIC to primary dentin was affected by the acid conditioning but the bur type had no influence.

Adhesive sealing of dentin surfaces in vitro: A review

Science.gov (United States)

Abu-Nawareg, Manar M; Zidan, Ahmed Z; Zhou, Jianfeng; Agee, Kelli; Chiba, Ayaka; Tagami, Jungi; Pashley, David H

2016-01-01

Purpose The purpose of this review is to describe the evolution of the use of dental adhesives to form a tight seal of freshly prepared dentin to protect the pulp from bacterial products, during the time between crown preparation and final cementum of full crowns. The evolution of these “immediate dentin sealants” follows the evolution of dental adhesives, in general. That is, they began with multiple-step, etch-and-rinse adhesives, and then switched to the use of simplified adhesives. Methods Literature was reviewed for evidence that bacteria or bacterial products diffusing across dentin can irritate pulpal tissues before and after smear layer removal. Smear layers can be solubilized by plaque organisms within 7–10 days if they are directly exposed to oral fluids. It is likely that smear layers covered by temporary restorations may last more than one month. As long as smear layers remain in place, they can partially seal dentin. Thus, many in vitro studies evaluating the sealing ability of adhesive resins use smear layer-covered dentin as a reference condition. Surprisingly, many adhesives do not seal dentin as well as do smear layers. Results Both in vitro and in vivo studies show that resin-covered dentin allows dentinal fluid to cross polymerized resins. The use of simplified single bottle adhesives to seal dentin was a step backwards. Currently, most authorities use either 3-step adhesives such as Scotchbond Multi-Purposea or OptiBond FLb or two-step self-etching primer adhesives, such as Clearfil SEc, Unifil Bondd or AdheSEe, respectfully. PMID:26846037

Temperature rise produced by different light-curing units through dentin.

Science.gov (United States)

Yazici, A Rüya; Müftü, Ali; Kugel, Gerard

2007-11-01

This study investigated the temperature rise caused by different light curing units and the temperature increase in dentin of different thicknesses. Dentin discs of 1.0 and 2.0 mm thicknesses were prepared from extracted human mandibular molars. Temperatures were recorded directly at the surface of the light guide tip, under dentin discs with different thicknesses, and through a sandwich composed of 2 mm thick cured composite and dentin using a K-type thermocouple. The curing units used were two quartz-tungsten-halogen lights (Spectrum and Elipar Trilight-ET) and a light-emitting diode (LED). The highest temperature rise was observed under a Mylar strip using ET standard mode. Under 1 and 2 mm thick dentin barriers, the lowest temperature rise was measured for the LED curing light. Significant differences in temperature rise existed among all curing units except between the Spectrum and ET exponential modes under a 1 mm thick dentin barrier with cured composite. Temperature rises were insignificant between the Spectrum and ET exponential modes and between two modes of Trilight when the same experimental setup was used under a 2 mm thick dentin barrier. For all curing units, temperature elevation through 2 mm of dentin was less than for 1 mm of dentin thickness. The ET standard mode produced the highest and the LED produced the lowest temperature rise for all tested conditions. The thickness of dentin and light-curing unit might affect temperature transmission.

Physicochemical Properties of Calcium Phosphate Based Coating on Gutta-Percha Root Canal Filling

Directory of Open Access Journals (Sweden)

Afaf Al-Haddad

2015-01-01

Full Text Available Dental Gutta-percha (GP is a polymer based standard root canal filling material that has been widely used in dentistry. However, it has an inadequate sealing ability and adhesion to root dentin. The aim of this study is to coat GP with a bioactive material to enhance its sealing ability and adhesion to the root sealer and subsequently to the root dentin. The choice of coating method is limited by the nature of GP as it requires a technique that is not governed by high temperatures or uses organic solvents. In this study, biomimetic coating technique using 1.5 Tas-simulated body fluids (SBF was employed to coat the treated GP cones. The coated samples were characterized using Fourier transform infrared spectroscopy (FTIR, X-ray Diffraction (XRD, and field emission scanning electron microscope (FESEM. The presence of hydroxyl, carbonate, and phosphate groups was detected by FTIR while the formation of hydroxyapatite (HA/calcium phosphate was confirmed with XRD. FESEM revealed uniform, thin, and crystalline HA calcium phosphate coating. The adhesion of the coating to the GP substrate was assessed with microscratch technique. It was viable with cohesive failure mode. In conclusion, Tas-SBF is able to coat pretreated GP cones with a crystalline apatitic calcium phosphate layer.

The use of plastic models for teaching root canal cleansing and shaping

Directory of Open Access Journals (Sweden)

Eftekhar B

2004-02-01

Full Text Available The use of root canal models in endodontics education is of high importance. So, in this article"na new method is presented that the students can produce these models with simple and low cost"ninstruments."nThese plastic models are made of polyester which is low cost, available and has the approximate cutting"nproperties of dentin. The best molds were disposable syringes due to their low cost, availability and"nproducing smooth surfaces on polyester models. A spreader with desired curve and tapering is used for"nproducing canals. Rockwell A hardness coefficient of polyester is "33", which is near dentin "31" and"nforeign made models "35.5". Since these polyester models can tolerate up to 280°C and have acceptable"nresistance to chloroform, all root canal therapy techniques such as vertical condensation and retreatments"nare practicable. Their transparency encourage the students to work on them. As a result, the use of these"nmodels is recommended for endodontics training.

Topical application of bFGF on acid-conditioned and non-conditioned dentin: effect on cell proliferation and gene expression in cells relevant for periodontal regeneration

Directory of Open Access Journals (Sweden)

Fernanda Regina Godoy Rocha

Full Text Available Abstract Periodontal regeneration is still a challenge in terms of predictability and magnitude of effect. In this study we assess the biological effects of combining chemical root conditioning and biological mediators on three relevant cell types for periodontal regeneration. Material and Methods: Bovine dentin slices were conditioned with 25% citric acid followed by topical application of basic fibroblast growth factor (bFGF, 10 and 50 ng. We used ELISA to assess the dynamics of bFGF release from the dentin surface and RT-qPCR to study the expression of Runx2, Col1a1, Bglap and fibronectin by periodontal ligament (PDL fibroblasts, cementoblasts and bone marrow stromal cells (BMSC grown onto these dentin slices. We also assessed the effects of topical application of bFGF on cell proliferation by quantification of genomic DNA. Results: Acid conditioning significantly increased the release of bFGF from dentin slices. Overall, bFGF application significantly (p<0.05 increased cell proliferation, except for BMSC grown on non-conditioned dentin slices. Dentin substrate discretely increased expression of Col1a1 in all cell types. Expression of Runx2, Col1a1 and Fn was either unaffected or inhibited by bFGF application in all cell types. We could not detect expression of the target genes on BMSC grown onto conditioned dentin. Conclusion: Acid conditioning of dentin improves the release of topically-applied bFGF. Topical application of bFGF had a stimulatory effect on proliferation of PDL fibroblasts, cementoblasts and BMSC, but did not affect expression of Runx2, Col1a1, Bglap and fibronectin by these cells.

The Effect of Diode Laser Treatment for Root Canal Disinfection on Fracture Resistance and Micro-hardness of the Tooth

International Nuclear Information System (INIS)

Elmiligy, H.H; Diab, A.H.; Sabet, N.E.; Saafan, A.M.

2014-01-01

This study evaluated the effect of diode laser treatment for root canal disinfection on fracture resistance and micro-hardness of the tooth. Sixty freshly extracted mandibular and maxillary premolars were accessed under coolant then root canals were flared up to apical preparation size 40 MFA coupled with 5.25% NaOCl as an irrigant. Teeth were divided into two groups, control group (group I) and lased group (group II) that was lased by diode laser with average power 2 w through fibrooptic into the canal 2 mm shorter than the apex. Each tooth was embedded in acrylic block, and then subjected to the fracture resistance test. Each root was then sectioned transversely and polished to record dentin Vickers hardness. Data was analysed with student t-test then with linear regression test. The Lased samples presented a significantly higher resistance to fracture than unlased samples. There was no statistically significant differences found between Vickers hardness (HV) of lased and unlased samples and there was no relation between fracture resistance and microhardness. Diode laser (980 nm) treatment had no adverse effect on dentin microhardness, also it increased the fracture resistance of dentin. Diode laser (980 nm) treatment could attain better function ability and maintenance of tooth after endodontic treatment.

Dentin biomodification: strategies, renewable resources and clinical applications.

Science.gov (United States)

Bedran-Russo, Ana K; Pauli, Guido F; Chen, Shao-Nong; McAlpine, James; Castellan, Carina S; Phansalkar, Rasika S; Aguiar, Thaiane R; Vidal, Cristina M P; Napotilano, José G; Nam, Joo-Won; Leme, Ariene A

2014-01-01

The biomodification of dentin is a biomimetic approach, mediated by bioactive agents, to enhance and reinforce the dentin by locally altering the biochemistry and biomechanical properties. This review provides an overview of key dentin matrix components, targeting effects of biomodification strategies, the chemistry of renewable natural sources, and current research on their potential clinical applications. The PubMed database and collected literature were used as a resource for peer-reviewed articles to highlight the topics of dentin hierarchical structure, biomodification agents, and laboratorial investigations of their clinical applications. In addition, new data is presented on laboratorial methods for the standardization of proanthocyanidin-rich preparations as a renewable source of plant-derived biomodification agents. Biomodification agents can be categorized as physical methods and chemical agents. Synthetic and naturally occurring chemical strategies present distinctive mechanism of interaction with the tissue. Initially thought to be driven only by inter- or intra-molecular collagen induced non-enzymatic cross-linking, multiple interactions with other dentin components are fundamental for the long-term biomechanics and biostability of the tissue. Oligomeric proanthocyanidins show promising bioactivity, and their chemical complexity requires systematic evaluation of the active compounds to produce a fully standardized intervention material from renewable resource, prior to their detailed clinical evaluation. Understanding the hierarchical structure of dentin and the targeting effect of the bioactive compounds will establish their use in both dentin-biomaterials interface and caries management. Copyright © 2013 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Adhesion of resin composite core materials to dentin.

Science.gov (United States)

O'Keefe, K L; Powers, J M

2001-01-01

This study determined (1) the effect of polymerization mode of resin composite core materials and dental adhesives on the bond strength to dentin, and (2) if dental adhesives perform as well to dentin etched with phosphoric acid as to dentin etched with self-etching primer. Human third molars were sectioned 2 mm from the highest pulp horn and polished. Three core materials (Fluorocore [dual cured], Core Paste [self-cured], and Clearfil Photo Core [light cured]) and two adhesives (Prime & Bond NT Dual Cure and Clearfil SE Bond [light cured]) were bonded to dentin using two dentin etching conditions. After storage, specimens were debonded in microtension and bond strengths were calculated. Scanning electron micrographs of representative bonding interfaces were analyzed. Analysis showed differences among core materials, adhesives, and etching conditions. Among core materials, dual-cured Fluorocore had the highest bond strengths. There were incompatibilities between self-cured Core Paste and Prime & Bond NT in both etched (0 MPa) and nonetched (3.0 MPa) dentin. Among adhesives, in most cases Clearfil SE Bond had higher bond strengths than Prime & Bond NT and bond strengths were higher to self-etched than to phosphoric acid-etched dentin. Scanning electron micrographs did not show a relationship between resin tags and bond strengths. There were incompatibilities between a self-cured core material and a dual-cured adhesive. All other combinations of core materials and adhesives produced strong in vitro bond strengths both in the self-etched and phosphoric acid-etched conditions.

Application of microcomputed tomography for quantitative analysis of dental root canal obturations

Directory of Open Access Journals (Sweden)

Anna Kierklo

2014-03-01

Full Text Available Introduction: The aim of the study was to apply microcomputed tomography to quantitative evaluation of voids and to test any specific location of voids in tooth’s root canal obturations. Materials and Methods: Twenty root canals were prepared and obturated with gutta-percha and Tubli-Seal sealer using the thermoplastic compaction method (System B + Obtura II. Roots were scanned and three-dimensional visualization was obtained. The volume and Feret’s diameter of I-voids (at the filling/dentine interface and S-voids (surrounded by filling material were measured.Results: The results revealed that none of the scanned root canal fillings were void-free. For I-voids, the volume fraction was significantly larger, but their number was lower (P = 0.0007, than for S-voids. Both types of voids occurred in characteristic regions (P < 0.001. I-voids occurred mainly in the apical third, while S-voids in the coronal third of the canal filling.Conclusions: Within the limitations of this study, our results indicate that microtomography, with proposed semi-automatic algorithm, is a useful tools for three-dimensional quantitative evaluation of dental root canal fillings. In canals filled with thermoplastic gutta-percha and Tubli-Seal, voids at the interface between the filling and canal dentine deserve special attention due to of their periapical location, which might promote apical microleakage. Further studies might help to elucidate the clinical relevance of these results.

Comparative evaluation of dentinal defects induced by hand files, hyflex, protaper next and one shape during canal preparation: A stereomicroscopic study

Directory of Open Access Journals (Sweden)

Ekta Garg

2017-01-01

Full Text Available Aim: This study aims to evaluate and compare the incidence of dentinal defects induced by Hand Files, HyFlex CM, ProTaper Next (PTN, and One Shape during canal preparation. Materials and Methods: One hundred and fifty extracted mandibular premolar teeth with single root canal were selected. Specimens were then divided into five groups with thirty specimens each. Group I: Specimens were prepared with hand instruments. Group II: Specimens were prepared with HyFlex CM rotary files (Coltene using a crown-down technique according to the manufacturer's instructions. Group III: Specimens were prepared with PTN rotary files (Dentsply using a crown-down technique according to the manufacturer's instructions. Group IV: Specimens were prepared with One Shape Single file rotary system (MicroMega using a crown-down technique according to the manufacturer's instructions. Group V: Specimens were used as a control and left unprepared. All roots were cut horizontally at 3, 6, and 9 mm from the apex. Sections were then viewed under stereomicroscope and dentinal defects were registered as “no defect,” “fracture,” and “other defects.” Statistical Analysis: Results of the study were subjected to Chi-square test. Results: Results were expressed as the number and percentage of defected, partially defected and roots with no defects in each groups. Conclusion: Hand files and One Shape file system caused less root defects compared to PTN and HyFlex file systems.

A comparison on the flexural strength of a new dental porcelain (D.} Dentin with Vita company Dentin porcelain (VMK 68N

Directory of Open Access Journals (Sweden)

Ghahramanloo A.

2004-06-01

Full Text Available Statement of Problem: Dental porcelain is one of the best materials ever used in dentistry. Excellent tissue"ncompatibility, esthetics, very low solubility in oral fluids, high compressive strength, and the lowest bacterial"nplaque accumulation on the glazed porcelain are some of its advantages. Porcelain brittleness due to its low"ntensile strength, impact strength and the occlusal attrition of opposing teeth enamel are some of its"ndisadvantages. The most important mechanical properties of dental porcelains are their flexural strength that is"nthe ability of a porcelain to resist fracture when loaded from above. Different ways have been proposed to"neliminate porcelain brittleness and develop its flexural strength, among which baking porcelain on a metal"nframework is more commonly used."nPurpose: Considering that restoration and replacement of teeth by porcelain fused to metal restorations is still"nthe most commonly used technique, the aim of the present study was to measure the flexural strength of a"nporcelain bonded to metal powder, D4 Dentin, and to compare it with Vita Dentin powder."nMaterials and Methods: In this experimental study, a stainless steel box, 25x5x2mm was made according to"nISO 6872: 1995 (E Standard and filled with D4 Dentin powder and Vita Dentin (VMK 68N and baked in"nVita furnace. Then 10 blocks of D^ Dentin and 10 of Vita Dentin were made. Samples were placed on the"nthree point bending test machine and force was applied the middle of each block. To analyze the data, t-"nstudent test and co-variance analysis were used."nResults: Mean flexural strength of D4 Dentin was 53.40±1.35 MPa and that of Vita Dentin was 53.86+7.38"nMPa. The difference was not statistically significant."nConclusion: According to ISO 6872: 1995 (E standard, the flexural strength of all D4 Dentin samples were"ngreater than 50 Mpa.

Effect of sonic application mode on the resin-dentin bond strength and dentin permeability of self-etching systems.

Science.gov (United States)

Mena-Serrano, Alexandra; Costa, Thays Regina Ferreira da; Patzlaff, Rafael Tiago; Loguercio, Alessandro Dourado; Reis, Alessandra

2014-10-01

To compare manual and sonic adhesive application modes in terms of the permeability and microtensile bond strength of a self-etching adhesive applied in the one-step or two-step protocol. Self-etching All Bond SE (Bisco) was applied as a one- or a two-step adhesive under manual or sonic vibration modes on flat occlusal dentin surfaces of 64 human molars. Half of the teeth were used to measure the hydraulic conductance of dentin at 200 cm H₂O hydrostatic pressure for 5 min immediately after the adhesive application. In the other half, composite buildups (Opallis) were constructed incrementally to create resin-dentin sticks with a cross-sectional area of 0.8 mm² to be tested in tension (0.5 mm/min) immediately after restoration placement. Data were analyzed using a two-way ANOVA and Tukey's test (α = 0.05). The fluid conductance of dentin was significantly reduced by the sonic vibration mode for both adhesives, but no effect on the bond strength values was observed for either adhesive. The sonic application mode at an oscillating frequency of 170 Hz can reduce the fluid conductance of the one- and two-step All Bond SE adhesive when applied on dentin.

Ex vivo analysis of root canal cleaning using Endo-PTC associated to NaOCl and different irrigant solutions

Directory of Open Access Journals (Sweden)

Andrea Kanako Yamazaki

2010-03-01

Full Text Available The aim of this study was to assess qualitatively, by means of SEM images, the cleaning of the dentin walls of root canals after chemical-surgical preparation using Endo-PTC cream with 0.5% and 1% sodium hypochlorite and different final irrigating solutions. Seventy-two single-rooted human teeth were divided into eight groups and prepared using Endo-PTC cream with sodium hypochlorite (NaOCl at different concentrations, and irrigated with NaOCl at different concentrations. Final irrigation was performed with either EDTA-T or EDTA-C. The best results were obtained with Group 1, followed by Groups 5, 2, 7, 8, 3, 6 and 4. We can conclude that the use of 0.5% NaOCl during instrumentation and final flush of the root canals was more efficient in cleaning than was 1% sodium hypochlorite. EDTA-T was more efficient in removing smear layer than EDTA-C, and the cervical third presented better cleaning of the root canal walls than did the middle third, which showed cleaner dentin walls than the apical third.

The effect of propolis fluoride on caries dentine activity

Science.gov (United States)

Darwita, Risqa Rina; Soekanto, Sri Angky; Finisha, Andanali Rhukul; Wahyuni, Hardiati Nur; Andiani, Salsabila Ghina

2018-02-01

This research was conducted to analyze the effect of propolis fluoride on the occurrence of arrested caries dentine surface. The design of the study was a clinical trial experimental. The respondent were primary school students aged 6-8 years, from primary school in Kukusan, Depok, West Java, Indonesia. They were screened of dental examination and the total number of 296 children with an age range of 6-8 year old were included in the study. All students who had dentin caries were get dental treatment with propolis fluoride topical application in dentin caries surface. After one month, two months and four months all students who were got propolis fluoride topical application in dentin caries surface were controlled. All data were analyzed by Wilcoxon test. The total number of dentinal decay of 296 student was 1740 surfaces indicated to Flolis topical application. After one, two and three months of Flolis application, all arrested of dentinal decay was evaluated, the result of evaluation from the second month to the third month evaluation was found that the arrested dentinal caries surfaces were decreased significantly at 29.36% (pcaries surface from the first month to the third month was decreased significantly at 38.62% (pcaries, and their ability to arrest dental caries was significantly different. Flolis was found to be effective in arresting dentinal caries surface until three months application, and should be repeated after 3 months of Flolis application.

Evaluation of the bond strength of resin cements used to lute ceramics on laser-etched dentin.

Science.gov (United States)

Giray, Figen Eren; Duzdar, Lale; Oksuz, Mustafa; Tanboga, Ilknur

2014-07-01

The purpose of this study was to investigate the shear bond strength (SBS) of two different adhesive resin cements used to lute ceramics on laser-etched dentin. Erbium, chromium: yttrium, scandium, gallium, garnet (Er,Cr:YSGG) laser irradiation has been claimed to improve the adhesive properties of dentin, but results to date have been controversial, and its compatibility with existing adhesive resin cements has not been conclusively determined. Two adhesive cements, one "etch-and-rinse" [Variolink II (V)] and one "self-etch" [Clearfil Esthetic Cement (C)] luting cement, were used to lute ceramic blocks (Vita Celay Blanks, Vita) onto dentin surfaces. In total, 80 dentin specimens were distributed randomly into eight experimental groups according to the dentin surface-etching technique used Er,Cr:YSGG laser and Er:YAG laser: (1) 37% orthophosphoric acid+V (control group), (2) Er,Cr:YSGG laser+V, (3) Er,Cr:YSGG laser+acid+V, (4) Er:YAG laser+V, (5) Er:YAG laser+acid+V, (6) C, (7) Er,Cr:YSGG laser+C, and (8) Er:YAG laser+C. Following these applications, the ceramic discs were bonded to prepared surfaces and were shear loaded in a universal testing machine until fracture. SBS was recorded for each group in MPa. Shear test values were evaluated statistically using the Mann-Whitney U test. No statistically significant differences were evident between the control group and the other groups (p>0.05). The Er,Cr:YSGG laser+A+V group demonstrated significantly higher SBS than did the Er,Cr:YSGG laser+V group (p=0.034). The Er,Cr:YSGG laser+C and Er:YAG laser+C groups demonstrated significantly lower SBS than did the C group (pceramic bond strengths, depending upon the adhesive cement used.

Transmission electron microscopical study of teenage crown dentin on the nanometer scale

Energy Technology Data Exchange (ETDEWEB)

Panfilov, Peter, E-mail: peter.panfilov@urfu.ru [Ural Federal University, Ekaterinburg (Russian Federation); Kabanova, Anna [Ural Federal University, Ekaterinburg (Russian Federation); Guo, Jinming; Zhang, Zaoli [Erich Schmid Institute for Materials Science, Austrian Academy of Sciences, Leoben (Austria)

2017-02-01

Statement of significance: This is the first transmission electron microscopic study of teenage crown dentin on the nanometer scale. Samples for TEM were prepared by mechanical thinning and chemical polishing that allowed obtaining the electron transparent foils. It was firstly shown that human dentin possesses the layered morphology: the layers are oriented normally to the main axis of a tooth and have the thickness of ~ 50 nm. HA inorganic phase of teenage crown dentin is in the amorphous state. The cellular structure, which was formed from collagen fibers (diameter is ~ 5 nm), are observed near DEJ region in teenage dentin, whereas bioorganic phase of teenage crown dentin near the pulp camera does not contain the collagen fibers. Cracks in dentin thin foils have sharp tips, but big angles of opening (~ 30{sup °}) with plastic zone ahead crack tip. It means that young crown human dentin exhibits ductile or viscous-elastic fracture behavior on the nanometer scale. - Highlights: • Dentin has layered morphology. • Mineral component of dentin is in amorphous state. • Collagen fibers form cellular structure in dentin. • Cracks in dentin behave by elastic-plastic manner.

Transmission electron microscopical study of teenage crown dentin on the nanometer scale

International Nuclear Information System (INIS)

Panfilov, Peter; Kabanova, Anna; Guo, Jinming; Zhang, Zaoli

2017-01-01

Statement of significance: This is the first transmission electron microscopic study of teenage crown dentin on the nanometer scale. Samples for TEM were prepared by mechanical thinning and chemical polishing that allowed obtaining the electron transparent foils. It was firstly shown that human dentin possesses the layered morphology: the layers are oriented normally to the main axis of a tooth and have the thickness of ~ 50 nm. HA inorganic phase of teenage crown dentin is in the amorphous state. The cellular structure, which was formed from collagen fibers (diameter is ~ 5 nm), are observed near DEJ region in teenage dentin, whereas bioorganic phase of teenage crown dentin near the pulp camera does not contain the collagen fibers. Cracks in dentin thin foils have sharp tips, but big angles of opening (~ 30 ° ) with plastic zone ahead crack tip. It means that young crown human dentin exhibits ductile or viscous-elastic fracture behavior on the nanometer scale. - Highlights: • Dentin has layered morphology. • Mineral component of dentin is in amorphous state. • Collagen fibers form cellular structure in dentin. • Cracks in dentin behave by elastic-plastic manner.

Carbodiimide Inactivation of MMPs and Effect on Dentin Bonding

Science.gov (United States)

Mazzoni, A.; Apolonio, F.M.; Saboia, V.P.A.; Santi, S.; Angeloni, V.; Checchi, V.; Curci, R.; Di Lenarda, R.; Tay, F.R.; Pashley, D.H.; Breschi, L.

2014-01-01

The use of protein cross-linking agents during bonding procedures has been recently proposed to improve bond durability. This study aimed to use zymography and in situ zymography techniques to evaluate the ability of 1-ethyl-3-(3-dimethylaminopropyl) carbodiimide (EDC) cross-linker to inhibit matrix metalloproteinase (MMP) activity. The hypotheses tested were that: (1) bonding procedures increase dentin gelatinolytic activity and (2) EDC pre-treatment prevents this enzymatic activity. The zymographic assay was performed on protein extracts obtained from dentin powder treated with Optibond FL or Scotchbond 1XT with or without 0.3M EDC pre-treatment. For in situ zymography, adhesive/dentin interfaces were created with the same adhesives applied to acid-etched dentin slabs pre-treated or not with EDC conditioner. Zymograms revealed increased expression of dentin endogenous MMP-2 and -9 after adhesive application, while the use of EDC as a primer inactivated dentin gelatinases. Results of in situ zymograpy showed that hybrid layers of tested adhesives exhibited intense collagenolytic activity, while almost no fluorescence signal was detected when specimens were pre-treated with EDC. The correlative analysis used in this study demonstrated that EDC could contribute to inactivate endogenous dentin MMPs within the hybrid layer created by etch-and-rinse adhesives. PMID:24334409

Characterization of Genipin-Modified Dentin Collagen

Directory of Open Access Journals (Sweden)

Hiroko Nagaoka

2014-01-01

Full Text Available Application of biomodification techniques to dentin can improve its biochemical and biomechanical properties. Several collagen cross-linking agents have been reported to strengthen the mechanical properties of dentin. However, the characteristics of collagen that has undergone agent-induced biomodification are not well understood. The objective of this study was to analyze the effects of a natural cross-linking agent, genipin (GE, on dentin discoloration, collagen stability, and changes in amino acid composition and lysyl oxidase mediated natural collagen cross-links. Dentin collagen obtained from extracted bovine teeth was treated with three different concentrations of GE (0.01%, 0.1%, and 0.5% for several treatment times (0–24 h. Changes in biochemical properties of NaB3H4-reduced collagen were characterized by amino acid and cross-link analyses. The treatment of dentin collagen with GE resulted in a concentration- and time-dependent pigmentation and stability against bacterial collagenase. The lysyl oxidase-mediated trivalent mature cross-link, pyridinoline, showed no difference among all groups while the major divalent immature cross-link, dehydro-dihydroxylysinonorleucine/its ketoamine in collagen treated with 0.5% GE for 24 h, significantly decreased compared to control (P< 0.05. The newly formed GE-induced cross-links most likely involve lysine and hydroxylysine residues of collagen in a concentration-dependent manner. Some of these cross-links appear to be reducible and stabilized with NaB3H4.

In vivo remineralization of dentin using an agarose hydrogel biomimetic mineralization system

Science.gov (United States)

Han, Min; Li, Quan-Li; Cao, Ying; Fang, Hui; Xia, Rong; Zhang, Zhi-Hong

2017-02-01

A novel agarose hydrogel biomimetic mineralization system loaded with calcium and phosphate was used to remineralize dentin and induce the oriented densely parallel packed HA layer on defective dentin surface in vivo in a rabbit model. Firstly, the enamel of the labial surface of rabbits’ incisor was removed and the dentin was exposed to oral environment. Secondly, the hydrogel biomimetic mineralization system was applied to the exposed dentin surface by using a custom tray. Finally, the teeth were extracted and evaluated by scanning electron microscopy, X-ray diffraction, and nanoindentation test after a certain time of mineralization intervals. The regenerated tissue on the dentin surface was composed of highly organised HA crystals. Densely packed along the c axis, these newly precipitated HA crystals were perpendicular to the underlying dental surface with a tight bond. The demineralized dentin was remineralized and dentinal tubules were occluded by the grown HA crystals. The nanohardness and elastic modulus of the regenerated tissue were similar to natural dentin. The results indicated a potential clinical use for repairing dentin-exposed related diseases, such as erosion, wear, and dentin hypersensitivity.

Clinical and morphologic evaluation of Er:YAG laser action at the front of cervical dentinal hypersensitivity; Avaliacao clinica e morfologica da acao do laser de Er:YAG frente a hipersensibilidade dentinaria cervical

Energy Technology Data Exchange (ETDEWEB)

Rocha, Dalva Maria

2001-07-01

This work was achieved in vivo and in vitro to evaluate the efficiency of Er:YAG laser in the cervical dentinal hypersensitivity treatment (HSDC). The Clinical study was achieved in patients with HSDC. The treatment was realized in five sessions: the first for selection, the second for exams (clinic and X-Ray) and trying to remove the etiologic factors that could cause the HSDC. The third and fourth sessions were subjected to the radiation with that protocol: 60 mJ energy ,2 Hz frequency, 6 mm out of focus, under air cooling, 20 seconds each application which the same was repeated four times with one minute breaks, which scanning movements and without using anaesthetics. The fifth was evaluation. The patients were evaluated and registered in a subject scale of pain 0 to 3, in the beginning and end of each session of irradiation, and one month after the last session. The results showed that for the irradiated group occurs significant differences in the beginning of each session and between. For the control group did not occur significant differences in the beginning and after each session, but did show a difference between the sessions. As the control group as the irradiated group, had reduction of sensibility between the session. For the morphologic study nine teeth were selected, 7 molars and 2 pre-molars from operative dentistry discipline. Half of the surface was irradiated with Er:YAG laser, the same protocol used in vivo, and the other half was used as a control without receiving any laser irradiation. Subsequently, specimens were prepared for SEM examinations. The results showed that laser treated surfaces showed a reduction of dentine tubular diameter with partial or total closure of the dentine tubules. For the control group, it was observed bigger amounts smear layer and open dentine tubular. The results obtained indicated that the Er:YAG laser can contribute to the HSDC treatment. (author)

In vivo Dentin Caries Model using Rat Molars

OpenAIRE

Takashi, HIGASHI; Junji, TAGAMI; Nobuhiro, HANADA; Cariology and Operative Dentistry, Department of Restorative Sciences, Tokyo Medical and Dental University; Cariology and Operative Dentistry, Department of Restorative Sciences, Tokyo Medical and Dental University; Department of Oral Science The National Institute of Infectious Diseases(NIID)

2000-01-01

Experimental dentinal caries was induced in rat molars which were inoculated orally with Streptococcus mutans and maintained on a carionenic diet 2000. After 30 days on the diet, the rats were sacrificed. The caries lesions were confirmed with a caries detector, then nanohardness determination of caries dentin were measured with nanoindentation. After hardness measurement, the lesion was examined by SEM and EDS. Dentin caries in sixteen fissures was induced among 20 fissures in the mandibular...

A micromechanics model of the elastic properties of human dentine

Energy Technology Data Exchange (ETDEWEB)

Kinney, J. H. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Balooch, M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Marshall, G. W. [Univ. of California, San Francisco, CA (United States). Dept. of Restorative Dentistry; Marshall, S. J. [Univ. of California, San Francisco, CA (United States). Dept. of Restorative Dentistry

1999-10-01

A generalized self-consistent model of cylindrical inclusions in a homogeneous and isotropic matrix phase was used to study the effects of tubule orientation on the elastic properties of dentin. Closed form expressions for the five independent elastic constants of dentin were derived in terms of tubule concentration, and the Young's moduli and Poisson ratios of peri- and intertubular dentin. An atomic force microscope (AFM) indentation technique determined the Young's moduli of the peri- and intertubular dentin as approximately 30 GPa and 15 GPa, respectively. Over the natural variation in tubule density found in dentin, there was only a slight variation in the axial and transverse shear moduli with position in the tooth, and there was no measurable effect of tubule orientation. We conclude that tubule orientation has no appreciable effect on the elastic behavior of normal dentin, and that the elastic properties of healthy dentin can be modeled as an isotropic continuum with a Young's modulus of approximately 16 GPa and a shear modulus of 6.2 GPa.

Nd:YAG laser associated with metal salts solutions in the treatment of dentinal hypersensitivity; O laser de Nd:YAG associado a solucoes de sais metalicos no tratamento da hipersensibilidade dentinaria

Energy Technology Data Exchange (ETDEWEB)

Glauche, Carlos Eugenio Correia

2001-07-01

The objective of this study was to observe the ultrastructural changes caused by the radiation of Nd:YAG laser on the tooth tissue and determine qualitatively the presence of Sn{sup ++}, Sr{sup ++} and F{sup -}, inside the dentin, being it irradiated or not. Ten molar teeth recently extracted were cut into 2 mm discs. The samples were soaked in a EDTA solution at 17% for 2 minutes and divided into five groups. Group I: the samples were irradiated with Nd:YAG laser (1,5 W, 100 mJ, 15 Hz, 150 {mu}s and 125 J/cm{sup 2}) and after that, a treatment with an SnF{sub 2} aqueous solution at 10% for 30 minutes. Group II: the samples got laser irradiation with the same parameters and then a treatment with an SrCl{sub 2} solution at 10% as a toothpaste (Sensodyne{sup TM}) for 30 minutes. Group III: the samples just got a treatment with a SnF{sub 2} aqueous solution at 10% for 30 minutes. Group IV: the samples just got a treatment with a SrCl{sub 2} toothpaste (Sensodyne{sup TM}) for 30 minutes. Group V: samples that just got laser irradiation in the parameters above mentioned. Then, all samples were prepared for scanning electronic microscopy (SEM) and the samples of groups I, II, III and IV for energy dispersive X-ray microanalysis (EDX). The ultrastructure aspect of the dentin showed the surface totally altered by the irradiation. Pits and whitish globules were found amidst an heterogenous and rough structure, due to the melting and resolidification of the dental structure. Craters were also observed. Carbonization areas were absent. Ions Sn{sup ++} were found at a depth of 250 {mu}m in the samples of group I (Nd:YAG + SnF{sub 2}), whereas in the samples of group III, Sn{sup ++} were not found deeper than 100 {mu}m. Sr{sup ++} could be detected at least at 500 {mu}m in the inner dentin in the samples of group II (Nd:YAG + SrCl{sub 2}). However, Sn{sup ++} were not found at 50 {mu}m in group IV samples. Ions F{sup -} were just found in the irradiated samples of group I

Dentin-bonded all-ceramic crowns: current status.

Science.gov (United States)

Burke, F J; Qualtrough, A J; Hale, R W

1998-04-01

Dentin-bonded all-ceramic crowns employ contemporary techniques to lute the crown to the tooth using a resin luting material and dentin-bonding system. The advantages of these crowns are that they provide good esthetics and fracture resistance and can be used in cases of substantial tooth loss. Their principal disadvantages are that the luting procedure is more time-consuming and that these crowns should not be used where margins are subgingival. Dentin-bonded all-ceramic crowns may be a useful addition to the dentist's armamentarium, but long-term clinical studies are needed to fully assess their performance.

Effect of reciprocating file motion on microcrack formation in root canals: an SEM study.

Science.gov (United States)

Ashwinkumar, V; Krithikadatta, J; Surendran, S; Velmurugan, N

2014-07-01

To compare dentinal microcrack formation whilst using Ni-Ti hand K-files, ProTaper hand and rotary files and the WaveOne reciprocating file. One hundred and fifty mandibular first molars were selected. Thirty teeth were left unprepared and served as controls, and the remaining 120 teeth were divided into four groups. Ni-Ti hand K-files, ProTaper hand files, ProTaper rotary files and WaveOne Primary reciprocating files were used to prepare the mesial canals. Roots were then sectioned 3, 6 and 9 mm from the apex, and the cut surface was observed under scanning electron microscope (SEM) and checked for the presence of dentinal microcracks. The control and Ni-Ti hand K-files groups were not associated with microcracks. In roots prepared with ProTaper hand files, ProTaper rotary files and WaveOne Primary reciprocating files, dentinal microcracks were present. There was a significant difference between control/Ni-Ti hand K-files group and ProTaper hand files/ProTaper rotary files/WaveOne Primary reciprocating file group (P ProTaper rotary files producing the most microcracks. No significant difference was observed between teeth prepared with ProTaper hand files and WaveOne Primary reciprocating files. ProTaper rotary files were associated with significantly more microcracks than ProTaper hand files and WaveOne Primary reciprocating files. Ni-Ti hand K-files did not produce microcracks at any levels inside the root canals. © 2013 International Endodontic Journal. Published by John Wiley & Sons Ltd.

Racemization of aspartic acid in root dentin as a tool for age estimation in a Kuwaiti population.

Science.gov (United States)

Elfawal, Mohamed Amin; Alqattan, Sahib Issa; Ghallab, Noha Ayman

2015-01-01

Estimation of age is one of the most significant tasks in forensic practice. Amino acid racemization is considered one of the most reliable and accurate methods of age estimation and aspartic acid shows a high racemization reaction rate. The present study has investigated the application of aspartic acid racemization in age estimation in a Kuwaiti population using root dentin from a total of 89 upper first premolar teeth. The D/L ratio of aspartic acid was obtained by HPLC technique in a test group of 50 subjects and a linear regression line was established between aspartic acid racemization and age. The correlation coefficient (r) was 0.97, and the standard error of estimation was ±1.26 years. The racemization age "t" of each subject was calculated by applying the following formula: ln [(1 + D/L)/(1 - D/L)] = 0.003181 t + (-0.01591). When the proposed formula "estimated age t = ln [(1 + D/L)/(1 - D/L)] + 0.01591/0.003181" was applied to a validation group of 39 subjects, the range of error was less than one year in 82.1% of the cases and the standard error of estimation was ±1.12. The current work has established a reasonably significant correlation of the D-/L-aspartic acid ratio with age, and proposed an apparently reliable formula for calculating the age in Kuwaiti populations through aspartic acid racemization. Further research is required to find out whether similar findings are applicable to other ethnic populations. © The Author(s) 2014 Reprints and permissions: sagepub.co.uk/journalsPermissions.nav.

Association between Severity of Tooth Wear and Dentinal Hypersensitivity

Directory of Open Access Journals (Sweden)

Ashok Ayer

2016-11-01

Full Text Available Background & Objectives: Tooth wear (attrition, abrasion, erosion, and abfraction is perceived globally as ever increasing problem. Several outcome of the tooth wear are hypersensitivity, esthetic problems, functional impairment, annoyance to the patient, and fracture of the tooth. Among these, the measurable and more commonly reported outcome is hypersensitivity to stimuli. Although dentin hypersensitivity is a common clinical condition and is generally reported by the patient after experiencing a sharp, short pain caused by one of the several different external stimuli, it is often inadequately understood. None of the scientific literature available till date attempted to establish the relationship between tooth wear and dentin hypersensitivity which could be a key factor in monitoring those patients.  The aim of the study was to estimate the association between severity of teeth wear and sensitivity in the patients with reported dentinal hypersensitivity.Materials & Methods: Fifty patients with dentin hypersensitivity were investigated for tooth wear. Tooth wear measured using exact tooth wear index and level of sensitivity to stimuli was recorded using a numerical rating scale. Results: Enamel wear at cervical region of teeth showed a positive correlation (p=.010, similarly, dentin wear at cervical region of teeth showed positive correlation and significant association (p<.001 with dentinal hypersensitivity.Conclusion: The observation supports a significant association between severities of tooth surface wear and dentinal hypersensitivity.

Shear bond strength of porcelain laminate veneers to enamel, dentine and enamel-dentine complex bonded with different adhesive luting systems.

Science.gov (United States)

Öztürk, Elif; Bolay, Şükran; Hickel, Reinhard; Ilie, Nicoleta

2013-02-01

The aim of this study was to evaluate the shear bond strength of porcelain laminate veneers to 3 different surfaces by means of enamel, dentine, and enamel-dentine complex. One hundred thirty-five extracted human maxillary central teeth were used, and the teeth were randomly divided into 9 groups (n=15). The teeth were prepared with 3 different levels for bonding surfaces of enamel (E), dentine (D), and enamel-dentine complex (E-D). Porcelain discs (IPS e.max Press, Ivoclar Vivadent) of 2mm in thickness and 4mm in diameter were luted to the tooth surfaces by using 2 light-curing (RelyX Veneer [RV], 3M ESPE; Variolink Veneer [VV], Ivoclar Vivadent) and a dual-curing (Variolink II [V2], Ivoclar Vivadent) adhesive systems according to the manufacturers' instructions. Shear bond strength test was performed in a universal testing machine at 0.5mm/min until bonding failure. Failure modes were determined under a stereomicroscope, and fracture surfaces were evaluated with a scanning electron microscope. The data were statistically analysed (SPSS 17.0) (p=0.05). Group RV-D exhibited the lowest bond strength value (5.42±6.6MPa). There was statistically no difference among RV-D, V2-D (13.78±8.8MPa) and VV-D (13.84±6.2MPa) groups (p>0.05). Group VV-E exhibited the highest bond strength value (24.76±8.8MPa). The type of tooth structure affected the shear bond strength of the porcelain laminate veneers to the 3 different types of tooth structures (enamel, dentine, and enamel-dentine complex). When dentine exposure is necessary during preparation, enough sound enamel must be protected as much as possible to maintain a good bonding; to obtain maximum bond strength, preparation margins should be on sound enamel. Copyright © 2012 Elsevier Ltd. All rights reserved.

Primary experimental studies on mid-infrared FEL irradiation on dental substances at BFEL

CERN Document Server

Biao, Z J; Gao Xue Ju; He Wei; Huang Yu Ying; Li Yong Gui; LiuNianQing; Wang Min Kai; Wu Gan; Yan Xue Pin; Zhang Guo Qing

2001-01-01

A free electron laser (FEL) with its characteristics of wide wavelength tunability, ultrashort pulse time structure, and high peak power density is predominantly superior to all other conventional lasers in applications. Several experimental studies on mid-infrared FEL irradiation on dental enamel and dentine were performed at the Beijing FEL. Experimental aims were to investigate changes in the hardness, ratios of P to Ca and Cs before and after irradiation on samples with a characteristic absorption wavelength of 9.66 mu m, in the colors of these sample surfaces after irradiation with different wavelengths around the peak wavelength. The time dependence of temperature of the dentine sample was measured with its ps pulse effects compared to that with a continuous CO sub 2 laser. FTIR absorption spectra in the range of 2.5-15.4 mu m for samples of these hard dental substances and pure hydroxyapatite were first examined to decide their chemical components and absorption maximums. Primary experimental results w...

[Mantle dentin as biomodel of materials for structural teeth restoration].

Science.gov (United States)

Starodubova, A V; Vinnichenko, Yu A; Pourovskaya, I Ya; Rusanov, F S

The article describes a structural element of natural teeth - mantle dentin. It has been shown that the presence of this element in the structure of a natural tooth largely ensures its strength under the influence of repeated loads in a functional oral environment and arrests crack growth at the enamel/dentine interface. This later effect is explained by the influence of a thin layer of mantle dentine, which has physical and mechanical characteristics different from that of the main dentin.

Bond strength of compomers to dentin using acidic primers.

Science.gov (United States)

Tate, W H; You, C; Powers, J M

1999-10-01

To determine the in vitro bond strengths of seven compomer/bonding agent restorative systems to human dentin. Seven compomer/bonding agents were bonded to human dentin, stored in water at 37 degrees C for 24 hours, and debonded in tension. Bonding conditions were with and without phosphoric acid etching, with and without the use of combined primer/bonding agents, and under moist and wet bond interfaces. Without phosphoric acid etching, F2000/F2000 Compomer Primer/Adhesive and F2000/Single Bond Dental Adhesive System were less sensitive to dentin wetness. With moist dentin, bond strengths of Dyract/Prime & Bond 2.1, Dyract AP/Prime & Bond 2.1, Hytac/OSB light-curing, one-component bonding agent, F2000/Single Bond, and Freedom/STAE single component light-cured dentin/enamel adhesive system, were improved with phosphoric acid etching. Also, with moist dentin, the bond strength of F2000/F2000 Compomer Primer/Adhesive in the 3M Clicker dispensing system was higher without phosphoric acid etching, whereas bonds of Compoglass/Syntac Single-component were not affected by phosphoric acid etching. Bonding did not occur without primer/bonding agent, regardless of surface condition or use of phosphoric acid etching.

Efficiency of final irrigation of root canal in removal of smear layer

Directory of Open Access Journals (Sweden)

Mitić Aleksandar

2009-01-01

Full Text Available Introduction A smear layer forms on the root canal walls as the consequence of root instrumentation. The smear layer formed in such a way considerably influences the quality of root obturation and endodontic treatment outcome. Objective The aim of this study was to ultrastructurally analyze the surface of intracanal dentine after removal of the smear layer by the solution of doxycycline, citric acid and detergent Tween-80 (MTAD. Methods The study involved 60 single-rooted, extracted, human teeth divided into four groups. All samples were instrumented by a step-back technique and manual K-files, and rinsed during instrumentation by 2% CHX and H2O2. The first group of samples was exclusively rinsed by CHX and H2O2; in the second group, besides using CHX and H2O2, MTAD solution was used for the final irrigation. The samples which were rinsed by distilled water (+ control and the samples rinsed by 5.25% NaOCl and 17% Na EDTA (-control served as control groups. All samples were observed under the scanning electronic microscope JEOL-JSM-5300. The coronary, middle and apex thirds of the radix region were analyzed. Results The obtained results of the SEM analysis showed that the application of 2% chlorhexidine and hydrogen peroxide did not give clear dentine walls, and the smear layer could not be removed completely. The application of the same combination (CHX and H2O2, added by the final MTAD irrigation solution, led to the efficient removal of the smear layer, while the morphological structure of dentine surface remained unchanged. Statistical analysis showed that canal walls in the experimental group with MTAD as the final irrigation were significantly clearer compared to the control group (p<0.001. Conclusion Based on the obtained results, it can be concluded that MTAD is an efficient solution for the final irrigation of the canal system.

Accelerated fatigue testing of dentin-composite bond with continuously increasing load.

Science.gov (United States)

Li, Kai; Guo, Jiawen; Li, Yuping; Heo, Young Cheul; Chen, Jihua; Xin, Haitao; Fok, Alex

2017-06-01

The aim of this study was to evaluate an accelerated fatigue test method that used a continuously increasing load for testing the dentin-composite bond strength. Dentin-composite disks (ϕ5mm×2mm) made from bovine incisor roots were subjected to cyclic diametral compression with a continuously increasingly load amplitude. Two different load profiles, linear and nonlinear with respect to the number of cycles, were considered. The data were then analyzed by using a probabilistic failure model based on the Weakest-Link Theory and the classical stress-life function, before being transformed to simulate clinical data of direct restorations. All the experimental data could be well fitted with a 2-parameter Weibull function. However, a calibration was required for the effective stress amplitude to account for the difference between static and cyclic loading. Good agreement was then obtained between theory and experiments for both load profiles. The in vitro model also successfully simulated the clinical data. The method presented will allow tooth-composite interfacial fatigue parameters to be determined more efficiently. With suitable calibration, the in vitro model can also be used to assess composite systems in a more clinically relevant manner. Copyright © 2017 The Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Influence of increment thickness on dentin bond strength and light transmission of composite base materials.

Science.gov (United States)

Omran, Tarek A; Garoushi, Sufyan; Abdulmajeed, Aous A; Lassila, Lippo V; Vallittu, Pekka K

2017-06-01

Bulk-fill resin composites (BFCs) are gaining popularity in restorative dentistry due to the reduced chair time and ease of application. This study aimed to evaluate the influence of increment thickness on dentin bond strength and light transmission of different BFCs and a new discontinuous fiber-reinforced composite. One hundred eighty extracted sound human molars were prepared for a shear bond strength (SBS) test. The teeth were divided into four groups (n = 45) according to the resin composite used: regular particulate filler resin composite: (1) G-ænial Anterior [GA] (control); bulk-fill resin composites: (2) Tetric EvoCeram Bulk Fill [TEBF] and (3) SDR; and discontinuous fiber-reinforced composite: (4) everX Posterior [EXP]. Each group was subdivided according to increment thickness (2, 4, and 6 mm). The irradiance power through the material of all groups/subgroups was quantified (MARC® Resin Calibrator; BlueLight Analytics Inc.). Data were analyzed using two-way ANOVA followed by Tukey's post hoc test. SBS and light irradiance decreased as the increment's height increased (p composite used. EXP presented the highest SBS in 2- and 4-mm-thick increments when compared to other composites, although the differences were not statistically significant (p > 0.05). Light irradiance mean values arranged in descending order were (p composites. Discontinuous fiber-reinforced composite showed the highest value of curing light transmission, which was also seen in improved bonding strength to the underlying dentin surface. Discontinuous fiber-reinforced composite can be applied safely in bulks of 4-mm increments same as other bulk-fill composites, although, in 2-mm thickness, the investigated composites showed better performance.

Diagnosis and Managment of Maxillary Incisor with Vertical Root Fracture: A Clinical Report with Three-Year Follow-Up

OpenAIRE

Kallel, Ines; Moussaoui, Eya; Chtioui, Fadwa; Douki, Nabiha

2018-01-01

According to the American Association of Endodontists, “a ‘true’ vertical root fracture is defined as a complete or incomplete fracture initiated from the root at any level, usually directed buccolingually.” Vertical root fracture (VRF) usually starts from an internal dentinal crack and develops over time, due to masticatory forces and occlusal loads. When they occur in teeth, those types of fractures can present difficulties in diagnosis, and there are however many clinic and radiographical ...

Effect of cobalt-60 irradiation on the developing tooth germ of rat

Energy Technology Data Exchange (ETDEWEB)

You, Dong Soo; Lee, Ki Sik [Department of Dental Radiology, Graduate School, Seoul National University, Seoul (Korea, Republic of)

1976-11-15

The author observed the effects of the cobalt-60 irradiation on the amelogenesis and dentinogenesis of the albino rat fetuses by means of histological and histochemical methods. Female in oestrus were mated overnight and examined the next morning for evidence of copulation. The lower left abdomen of mothers were exposed to cobalt-60 irradiation on the 10th day of gestation, 100R 200R and 300R respectively. The fetuses were removed from the mothers on the 18th day of gestation. The employed histochemical methods were PAS reaction, colloidal iron reaction, aldehyde fuchsin stain, -amino acid reaction, -SH radical reaction, and methyl green pyronin stain. The results were as follows; 1. The group irradiated by 100R made no histological differences in comparison with the control group. 2. Increasing the irradiation to 200R, abnormal dentin formation occurred, and resulted in enamel hypoplasia, atrophy, and necrosis of odontoblasts. In dentinal papilla, the dilation and the degeneration of the blood vessels, excessive reticular atrophy, and osteodentin were revealed. 3. With the more irradiation (200R-300R), the positive material of PAS, {alpha}-amino acid and aldehyde fuchsin tended to decrease in the ameloblast and in the odontoblast. No significant changes appeared in DNA, the stainability of methylgreen pyronin.

Effect of cobalt-60 irradiation on the developing tooth germ of rat

International Nuclear Information System (INIS)

You, Dong Soo; Lee, Ki Sik

1976-01-01

The author observed the effects of the cobalt-60 irradiation on the amelogenesis and dentinogenesis of the albino rat fetuses by means of histological and histochemical methods. Female in oestrus were mated overnight and examined the next morning for evidence of copulation. The lower left abdomen of mothers were exposed to cobalt-60 irradiation on the 10th day of gestation, 100R 200R and 300R respectively. The fetuses were removed from the mothers on the 18th day of gestation. The employed histochemical methods were PAS reaction, colloidal iron reaction, aldehyde fuchsin stain, -amino acid reaction, -SH radical reaction, and methyl green pyronin stain. The results were as follows; 1. The group irradiated by 100R made no histological differences in comparison with the control group. 2. Increasing the irradiation to 200R, abnormal dentin formation occurred, and resulted in enamel hypoplasia, atrophy, and necrosis of odontoblasts. In dentinal papilla, the dilation and the degeneration of the blood vessels, excessive reticular atrophy, and osteodentin were revealed. 3. With the more irradiation (200R-300R), the positive material of PAS, α-amino acid and aldehyde fuchsin tended to decrease in the ameloblast and in the odontoblast. No significant changes appeared in DNA, the stainability of methylgreen pyronin.

Comparative Evaluation of Efficacy of Iontophoresis with 0.33% Sodium Fluoride Gel and Diode Laser Alone on Occlusion of Dentinal Tubules.

Science.gov (United States)

Patil, Anup Raghunath; Varma, Siddhartha; Suragimath, Girish; Abbayya, Keshava; Zope, Sameer Anil; Kale, Vishwajeet

2017-08-01

Dentinal Hypersensitivity (DH) is one of the most commonly encountered clinical problems. Literature reveals no specific therapy to satisfactorily eliminate dentinal hypersensitivity. The aim of this study was to assess and compare the efficacy of iontophoresis with 0.33% Sodium Fluoride (NaF) gel and diode laser alone in dentinal tubule occlusion. This in vitro study included 20 teeth with intact root surfaces unaltered by extraction procedure for specimen preparation. Each tooth was cleaned, air dried and cut into three sections. Total 60 sections were prepared (30 longitudinal and 30 transverse sections), which were acid etched. In control group, no treatment was carried. In iontophoresis treatment group, samples were inserted into a foam tray containing 0.33 % NaF Gel and subjected to 1.5 mA output current for three minutes. In laser treatment group, specimens were lased with 980 nm diode laser at 0.5 W/PW (62.2J /cm 2 ) in a noncontact mode for 30 seconds. Specimens were evaluated under Scanning Electron Microscope (SEM) at 10KV to 20KV under x 2000, x5000 magnification for surface characteristics and patency of dentinal tubules. Total number of tubules visible, open, completely and partially occluded were recorded in each microphotograph and compared. On comparison, laser group showed the least number of open tubules i.e., 130 (31.1%) followed by iontophoresis group, 155 (51.32%) and control group 417 (100%). Diode laser application provided better results as compared to iontophoresis on occlusion of dentinal tubules. Hence, it can be used to treat the patients with DH.

Water evaporation from substrate tooth surface during dentin treatments.

Science.gov (United States)

Kusunoki, Mizuho; Itoh, Kazuo; Gokan, Yuka; Nagai, Yoshitaka; Tani, Chihiro; Hisamitsu, Hisashi

2011-01-01

The purpose of this study was to evaluate changes in the quantity of water evaporation from tooth surfaces. The amount of water evaporation was measured using Multi probe adapter MPA5 and Tewameter TM300 (Courage+Khazaka Electric GmbH, Köln, Germany) after acid etching and GM priming of enamel; and after EDTA conditioning and GM priming of dentin. The results indicated that the amount of water evaporation from the enamel surface was significantly less than that from the dentin. Acid etching did not affect the water evaporation from enamel, though GM priming significantly decreased the evaporation (83.48 ± 15.14% of that before priming). The evaporation from dentin was significantly increased by EDTA conditioning (131.38 ± 42.08% of that before conditioning) and significantly reduced by GM priming (80.26 ± 7.43% of that before priming). It was concluded that dentin priming reduced water evaporation from the dentin surface.

Biomineralization ability and interaction of mineral trioxide aggregate and white portland cement with dentin in a phosphate-containing fluid.

Science.gov (United States)

Reyes-Carmona, Jessie F; Felippe, Mara S; Felippe, Wilson T

2009-05-01

Mineral trioxide aggregate (MTA) has been shown to be bioactive because of its ability to produce biologically compatible carbonated apatite. This study analyzed the interaction of MTA and white Portland cement with dentin after immersion in phosphate-buffered saline (PBS). Dentin disks with standardized cavities were filled with ProRoot MTA, MTA Branco, MTA BIO, white Portland cement + 20% bismuth oxide (PC1), or PC1 + 10% of calcium chloride (PC2) and immersed in 15 mL of PBS for 2 months. The precipitates were weighed and analyzed by scanning electron microscopy (SEM) and x-ray diffraction. The calcium ion release and pH of the solutions were monitored at 5, 15, 25, and 35 days. The samples were processed for SEM observations. Data were analyzed by using analysis of variance or Kruskall-Wallis tests. Our findings revealed the presence of amorphous calcium phosphate precipitates with different morphologies. The apatite formed by the cement-PBS system was deposited within collagen fibrils, promoting controlled mineral nucleation on dentin, observed as the formation of an interfacial layer with tag-like structures. All the cements tested were bioactive. The cements release some of their components in PBS, triggering the initial precipitation of amorphous calcium phosphates, which act as precursors during the formation of carbonated apatite. This spontaneous precipitation promotes a biomineralization process that leads to the formation of an interfacial layer with tag-like structures at the cement-dentin interface.

Push-out bond strength of different tricalcium silicate-based filling materials to root dentin

Directory of Open Access Journals (Sweden)

Jorge Henrique Stefaneli Marques

2018-03-01

Full Text Available Abstract: The aim of this study was to evaluate the bond strength of different triccalcium silicate cements to retrograde cavity using a push out test. Thirty maxillary central incisors were shaped using #80 hand files and sectioned transversally. Root slices were obtained from the apical 4 mm after eliminating the apical extremity. The specimens were embedded in acrylic resin and positioned at 45° to the horizontal plane for preparation of root-end cavities with a diamond ultrasonic retrotip. The samples were divided into three groups according to the root-end filling material (n = 10: MTA Angelus, ProRoot MTA and Biodentine. A gutta-percha cone (#80 was tugged-back at the limit between the canal and the root-end cavity. The root-end cavity was filled and the gutta-percha cone was removed after complete setting of the materials. The specimens were placed in an Instron machine with the root-end filling turned downwards. The push-out shaft was inserted in the space previously occupied by the gutta-percha cone and push out testing was performed at a crosshead speed of 1.0 mm/min. There was no statistically significant difference in resistance to push out by the materials tested (p > 0.01. MTA Angelus and ProRoot MTA showed predominantly mixed failure while Biodentine exhibited mixed and cohesive failures. The tricalcium silicate-based root-end filling materials showed similar bond strength retrograde cavity.

Push-out bond strength of different tricalcium silicate-based filling materials to root dentin.

Science.gov (United States)

Stefaneli Marques, Jorge Henrique; Silva-Sousa, Yara Teresinha Corrêa; Rached-Júnior, Fuad Jacob Abi; Macedo, Luciana Martins Domingues de; Mazzi-Chaves, Jardel Francisco; Camilleri, Josette; Sousa-Neto, Manoel Damião

2018-03-08

The aim of this study was to evaluate the bond strength of different triccalcium silicate cements to retrograde cavity using a push out test. Thirty maxillary central incisors were shaped using #80 hand files and sectioned transversally. Root slices were obtained from the apical 4 mm after eliminating the apical extremity. The specimens were embedded in acrylic resin and positioned at 45° to the horizontal plane for preparation of root-end cavities with a diamond ultrasonic retrotip. The samples were divided into three groups according to the root-end filling material (n = 10): MTA Angelus, ProRoot MTA and Biodentine. A gutta-percha cone (#80) was tugged-back at the limit between the canal and the root-end cavity. The root-end cavity was filled and the gutta-percha cone was removed after complete setting of the materials. The specimens were placed in an Instron machine with the root-end filling turned downwards. The push-out shaft was inserted in the space previously occupied by the gutta-percha cone and push out testing was performed at a crosshead speed of 1.0 mm/min. There was no statistically significant difference in resistance to push out by the materials tested (p > 0.01). MTA Angelus and ProRoot MTA showed predominantly mixed failure while Biodentine exhibited mixed and cohesive failures. The tricalcium silicate-based root-end filling materials showed similar bond strength retrograde cavity.

Micro-CT evaluation of root and canal morphology of mandibular first premolars with radicular grooves

Energy Technology Data Exchange (ETDEWEB)

Boschetti, Emanuele; Mazzi-Chaves, Jardel Francisco; Versiani, Marco Aurélio; Pécora, Jesus Djalma; Saquy, Paulo Cesar; Sousa Neto, Manoel Damião de, E-mail: sousanet@forp.usp.br [Universidade de São Paulo (USP), Ribeirao Preto, SP (Brazil). Departamento de Odontologia Restauradora; Silva-Sousa, Yara Terezinha Correa; Leoni, Graziela Bianchi [Universidade de Ribeirão Preto (UNAERP), Ribeirão Preto, SP (Brazil). Departmento de Endodontia

2017-09-15

The aim of this study was to evaluate morphological features of 70 single-rooted mandibular first premolars with radicular grooves (RG) using micro-CT technology. Teeth were scanned and evaluated regarding the morphology of the roots and root canals as well as length, depth and percentage frequency location of the RG. Volume, surface area and Structure Model Index (SMI) of the canals were measured for the full root length. Two-dimensional parameters and frequency of canal orifices were evaluated at 1, 2, and 3 mm levels from the apical foramen. The number of accessory canals, the dentin thickness, and cross-sectional appearance of the canal at different root levels were also recorded. Expression of deep grooves was observed in 21.42% of the sample. Mean lengths of root and RG were 13.43 mm and 8.5 mm, respectively, while depth of the RG ranged from 0.75 to 1.13 mm. Mean canal volume, surface area and SMI were 10.78 mm{sup 3}, 58.51 mm{sup 2}, and 2.84, respectively. Apical delta was present in 4.35% of the sample and accessory canals were observed mostly at the middle and apical thirds. Two-dimensional parameters indicated an oval-shaped cross-sectional appearance of the root canal with a high percentage frequency of canal divisions (87.15%). Canal configuration type V (58.57%) was the most prevalent. C-shaped configuration was observed in 13 premolars (18.57%), whereas dentin thickness ranged from 1.0 to 1.31 mm. Radicular grooves in mandibular first premolars was associated with the occurrence of several anatomical complexities, including C-shaped canals and divisions of the main root canal. (author)

Micro-CT evaluation of root and canal morphology of mandibular first premolars with radicular grooves

International Nuclear Information System (INIS)

Boschetti, Emanuele; Mazzi-Chaves, Jardel Francisco; Versiani, Marco Aurélio; Pécora, Jesus Djalma; Saquy, Paulo Cesar; Sousa Neto, Manoel Damião de; Silva-Sousa, Yara Terezinha Correa; Leoni, Graziela Bianchi

2017-01-01

The aim of this study was to evaluate morphological features of 70 single-rooted mandibular first premolars with radicular grooves (RG) using micro-CT technology. Teeth were scanned and evaluated regarding the morphology of the roots and root canals as well as length, depth and percentage frequency location of the RG. Volume, surface area and Structure Model Index (SMI) of the canals were measured for the full root length. Two-dimensional parameters and frequency of canal orifices were evaluated at 1, 2, and 3 mm levels from the apical foramen. The number of accessory canals, the dentin thickness, and cross-sectional appearance of the canal at different root levels were also recorded. Expression of deep grooves was observed in 21.42% of the sample. Mean lengths of root and RG were 13.43 mm and 8.5 mm, respectively, while depth of the RG ranged from 0.75 to 1.13 mm. Mean canal volume, surface area and SMI were 10.78 mm 3 , 58.51 mm 2 , and 2.84, respectively. Apical delta was present in 4.35% of the sample and accessory canals were observed mostly at the middle and apical thirds. Two-dimensional parameters indicated an oval-shaped cross-sectional appearance of the root canal with a high percentage frequency of canal divisions (87.15%). Canal configuration type V (58.57%) was the most prevalent. C-shaped configuration was observed in 13 premolars (18.57%), whereas dentin thickness ranged from 1.0 to 1.31 mm. Radicular grooves in mandibular first premolars was associated with the occurrence of several anatomical complexities, including C-shaped canals and divisions of the main root canal. (author)

[Evaluation of preparation of curved root canals using hand-used ProTaper].

Science.gov (United States)

Nie, Min; Zhao, Xin-Chen; Peng, Bin; Fan, Ming-Wen; Bian, Zhuan

2009-05-01

To evaluate the shaping ability of hand-used ProTaper on curved canals using Endodontic Cube. Fifty-four curved root canals in vitro were selected and divided into three groups according to the curved degree (alpha), group A: 0 degrees hand-used ProTaper. Before and after shaping, photograph of all the sections were taken under a stereomicroscope. Statistical analyses were performed. The dentin cutting quantity of the whole canal prepared with ProTaper in group B and C was larger than that of group A. The deviation distance of the whole canal prepared by ProTaper in group C was significantly larger than that in group A, and the deviation distance in middle portion larger than that in group B. The maintaining ability in the middle portion of group C by ProTaper was worse than that of group A and B. The curvature of root canal may increase the cutting quantity of the -dentin and reduce the ability of remaining original canal shape prepared by ProTaper.

The reduction in fatigue crack growth resistance of dentin with depth.

Science.gov (United States)

Ivancik, J; Neerchal, N K; Romberg, E; Arola, D

2011-08-01

The fatigue crack growth resistance of dentin was characterized as a function of depth from the dentino-enamel junction. Compact tension (CT) specimens were prepared from the crowns of third molars in the deep, middle, and peripheral dentin. The microstructure was quantified in terms of the average tubule dimensions and density. Fatigue cracks were grown in-plane with the tubules and characterized in terms of the initiation and growth responses. Deep dentin exhibited the lowest resistance to the initiation of fatigue crack growth, as indicated by the stress intensity threshold (ΔK(th) ≈ 0.8 MPa•m(0.5)) and the highest incremental fatigue crack growth rate (over 1000 times that in peripheral dentin). Cracks in deep dentin underwent incremental extension under cyclic stresses that were 40% lower than those required in peripheral dentin. The average fatigue crack growth rates increased significantly with tubule density, indicating the importance of microstructure on the potential for tooth fracture. Molars with deep restorations are more likely to suffer from the cracked-tooth syndrome, because of the lower fatigue crack growth resistance of deep dentin.

Deformation behavior of human dentin in liquid nitrogen: a diametral compression test.

Science.gov (United States)

Zaytsev, Dmitry; Panfilov, Peter

2014-09-01

Contribution of the collagen fibers into the plasticity of human dentin is considered. Mechanical testing of dentin at low temperature allows excluding the plastic response of its organic matrix. Therefore, deformation and fracture behavior of the dentin samples under diametral compression at room temperature and liquid nitrogen temperature are compared. At 77K dentin behaves like almost brittle material: it is deformed exclusively in the elastic regime and it fails due to growth of the sole crack. On the contrary, dentin demonstrates the ductile response at 300K. There are both elastic and plastic contributions in the deformation of dentin samples. Multiple cracking and crack tip blunting precede the failure of samples. Organic phase plays an important role in fracture of dentin: plasticity of the collagen fibers could inhibit the crack growth. Copyright © 2014 Elsevier B.V. All rights reserved.

Molecular detection of bacteria associated to caries activity in dentinal lesions.

Science.gov (United States)

Neves, Beatriz Gonçalves; Stipp, Rafael Nóbrega; da Silva Bezerra, Daniela; de Figueiredo Guedes, Sarah Florindo; Rodrigues, Lidiany Karla Azevedo

2017-07-01

This study aimed at identifying and quantifying Actinomyces naeslundii, Bifidobacterium spp., Streptococcus mitis group, Lactobacillus acidophilus, Lactobacillus casei group, Streptococcus gordonii, and Streptococcus mutans in active and inactive carious dentine lesions of children with early childhood caries by using quantitative polymerase chain reaction. Fifty-six dentin lesion samples, classified as active (n = 39) or inactive (n = 17), were collected from children aged from 2 to 5 years old. Dentinal-cavitated lesions were evaluated by Nyvad criteria for the assessment of caries lesion activity. Relative quantification revealed that Bifidobacterium spp. and the L. casei group were significantly more abundant in active dentin lesions (p oral microbiota related to dentin caries activity status is relevant, this study provides insights to better understand the differences in the microbiotas between active and arrested dentin cavities.

Parturition lines in modern human wisdom tooth roots: do they exist, can they be characterized and are they useful for retrospective determination of age at first reproduction and/or inter-birth intervals?

Science.gov (United States)

Dean, M Christopher; Elamin, Fadil

2014-01-01

Parturition lines have been described in the teeth of a number of animals, including primates, but never in modern humans. These accentuated lines in dentine are comprised of characteristic dark and light component zones. The aim of this study was to review the physiology underlying these lines and to ask if parturition lines exist in the third molar tooth roots of mothers known to have had one or more children during their teenage years. Brief retrospective oral medical obstetric histories were taken from four mothers and compared with histological estimates for the timing of accentuated markings visible in longitudinal ground sections of their wisdom teeth. Evidence of accentuated markings in M3 root dentine matched the age of the mother at the time their first child was born reasonably well. However, the dates calculated for inter-birth intervals did not match well. Parturition lines corresponding to childbirth during the teenage years can exist in human M3 roots, but may not always do so. Without a written medical history it would not be possible to say with confidence that an accentuated line in M3 root dentine was caused by stress, illness or was a parturition line.

308-nm excimer laser in endodontics

Science.gov (United States)

Liesenhoff, Tim

1992-06-01

Root canal preparation was performed on 20 extracted human teeth. After opening the coronal pulp, the root canals were prepared by 308 nm excimer laser only. All root canals were investigated under SEM after separation in the axial direction. By sagittal separation of the mandibles of freshly slaughtered cows, it was possible to get access to the tissues and irradiate under optical control. Under irradiation of excimer laser light, tissue starts to fluoresce. It was possible to demonstrate that each tissue (dentin, enamel, bone, pulpal, and connective tissue) has a characteristic spectral pattern. The SEM analyses showed that it is well possible to prepare root canals safely. All organic soft tissue has been removed by excimer laser irradiation. There was no case of via falsa. The simultaneous spectroscopic identification of the irradiated tissue provides a safe protection from overinstrumentation. First clinical trials on 20 patients suffering of chronical apical parodontitis have been carried out successfully.

The Difference of Structural State and Deformation Behavior between Teenage and Mature Human Dentin

Directory of Open Access Journals (Sweden)

Peter Panfilov

2016-01-01

Full Text Available Objective. The cause of considerable elasticity and plasticity of human dentin is discussed in the relationship with its microstructure. Methods. Structural state of teenage and mature human dentin is examined by using XRD and TEM techniques, and their deformation behavior under compression is studied as well. Result. XRD study has shown that crystallographic type of calcium hydroxyapatite in human dentin (calcium hydrogen phosphate hydroxide Ca9HPO4(PO45OH; Space Group P63/m (176; a = 9,441 A; c = 6,881 A; c/a = 0,729; Crystallite (Scherrer 200 A is the same for these age groups. In both cases, dentin matrix is X-ray amorphous. According to TEM examination, there are amorphous and ultrafine grain phases in teenage and mature dentin. Mature dentin is stronger on about 20% than teenage dentin, while teenage dentin is more elastic on about 20% but is less plastic on about 15% than mature dentin. Conclusion. The amorphous phase is dominant in teenage dentin, whereas the ultrafine grain phase becomes dominant in mature dentin. Mechanical properties of human dentin under compression depend on its structural state, too.

Molecular study of the dentin-pulp complex responses to caries progression

Directory of Open Access Journals (Sweden)

Yani Corvianindya Rahayu

2007-03-01

Full Text Available The dentin-pulp complex exhibits various responses to caries, including events of injury, defense, and repair. The overall responses dependent on pulp cell activity and the signaling processes, which regulate the behavior of these cells. The signals for tissue repair are thought to be mediated by dentin-bound growth factors released during caries progression. Growth factors are a key of molecules responsible for signaling a variety of cellular process following dental injury. The endogenous proteolytic enzymes (Matrix metalloproteinases, MMPs present in dentin matrix might also participate in releasing bioactive molecule. Several members of the MMP family are found in the soft and hard tissue compartment of dentin-pulp complex. Their presumed role in many physiological process during the development and maintenance of the dentin-pulp complex, they may also contribute to the pathogenesis of dentin caries and the responses elicited by caries.

Effects of fluoride and epigallocatechin gallate on soft-drink-induced dental erosion of enamel and root dentin.

Science.gov (United States)

Wang, Yin-Lin; Chang, Hao-Hueng; Chiang, Yu-Chih; Lu, Yu-Chen; Lin, Chun-Pin

2018-04-01

Fluoride and epigallocatechin gallate (EGCG) have been proven to prevent dental caries. The purpose of this study was to evaluate the effects of fluoride and EGCG on soft-drink-induced dental erosion in vitro. Forty enamel and dentin specimens were prepared from extracted human teeth. The specimens were divided into 4 groups and treated separately with distilled water (as control), 0.5 M sodium fluoride (NF), 400 μM EGCG (EG), and a solution containing 0.5 M NaF and 400 μM EGCG (FG). Cyclic erosive treatment was performed according to the experimental procedures. The specimens were analyzed using laser scanning confocal microscopy, scanning electron microscopy, and a microhardness tester. The data were analyzed using ANOVA and Bonferroni's post hoc test. The significance level was set at 5%. The amount of substance loss was lower in the NF and EG groups than in the control group (p erosion-caused substance loss was more pronounced in the dentin than in the enamel specimens. Surface microhardness loss was lower in the NF and EG groups than in the control group (p erosion compared with the control group. Fluoride and EGCG may interfere with each other. The mechanisms of the anti-erosive effect need to be explored in the future. Copyright © 2018. Published by Elsevier B.V.

Remineralizing Efficacy of Fluorohydroxyapatite Gel on Artificial Dentinal Caries Lesion

Directory of Open Access Journals (Sweden)

Qianqian Wang

2015-01-01

Full Text Available The aim was to evaluate the remineralizing efficacy of fluorohydroxyapatite (FHA gel on artificial dentinal caries lesion in vitro. Artificial carious lesions were made on occlusal cavities of teeth by exposing the dentin surface to a demineralizing solution. Each cavity was capped with a 3 mm thick FHA gel for 4 weeks. After the FHA gel was removed, the surface morphology and structure of the dentin were characterized by scanning electron microscopy (SEM, energy-dispersive X-ray spectroscopy (EDX, X-ray diffraction (XRD, and Fourier transform infrared spectroscopy (FT-IR. The dentin mineral density (DMD was measured by micro-computed tomography (Micro-CT. A layer of dense and orderly hexagonal crystal structure, with average diameter of 1 μm and thickness of 4~5 μm, could be observed on dentin surface. These crystals exhibited elemental peaks for calcium, phosphorus, carbon, and oxygen and characteristic peaks of hydroxyapatite (HA and fluorapatite (FA via XRD and FT-IR. The DMD of dentin surface layer significantly increased after it was capped with FHA gel (P<0.05. In the present study, the FHA gel could rapidly construct apatite on the artificial dentin caries surface and significantly increase the mineral density, which suggests that FHA gel might be a proper IPT material with remineralizing function.

Characterization of Dentine to Assess Bond Strength of Dental Composites

Directory of Open Access Journals (Sweden)

Saad Liaqat

2015-04-01

Full Text Available This study was performed to develop alternating dentine adhesion models that could help in the evaluation of a self-bonding dental composite. For this purpose dentine from human and ivory was characterized chemically and microscopically before and after acid etching using Raman and SEM. Mechanical properties of dentine were determined using 3 point bend test. Composite bonding to dentine, with and without use of acid pre-treatment and/or the adhesive, were assessed using a shear bond test. Furthermore, micro gap formation after restoration of 3 mm diameter cavities in dentine was assessed by SEM. Initial hydroxyapatite level in ivory was half that in human dentine. Surface hydroxyapatites decreased by approximately half with every 23 s of acid etch. The human dentine strength (56 MPa was approximately double that of ivory, while the modulus was almost comparable to that of ivory. With adhesive use, average shear bond strengths were 30 and 26 MPa with and without acid etching. With no adhesive, average bond strength was 6 MPa for conventional composites. This, however, increased to 14 MPa with a commercial flowable “self–bonding” composite or upon addition of low levels of an acidic monomer to the experimental composite. The acidic monomer additionally reduced micro-gap formation with the experimental composite. Improved bonding and mechanical properties should reduce composite failures due to recurrent caries or fracture respectively.

Different methods of dentin processing for application in bone tissue engineering: A systematic review.

Science.gov (United States)

Tabatabaei, Fahimeh Sadat; Tatari, Saeed; Samadi, Ramin; Moharamzadeh, Keyvan

2016-10-01

Dentin has become an interesting potential biomaterial for tissue engineering of oral hard tissues. It can be used as a scaffold or as a source of growth factors in bone tissue engineering. Different forms of dentin have been studied for their potential use as bone substitutes. Here, we systematically review different methods of dentin preparation and the efficacy of processed dentin in bone tissue engineering. An electronic search was carried out in PubMed and Scopus databases for articles published from 2000 to 2016. Studies on dentin preparation for application in bone tissue engineering were selected. The initial search yielded a total of 1045 articles, of which 37 were finally selected. Review of studies showed that demineralization was the most commonly used dentin preparation process for use in tissue engineering. Dentin extract, dentin particles (tooth ash), freeze-dried dentin, and denatured dentin are others method of dentin preparation. Based on our literature review, we can conclude that preparation procedure and the size and shape of dentin particles play an important role in its osteoinductive and osteoconductive properties. Standardization of these methods is important to draw a conclusion in this regard. © 2016 Wiley Periodicals, Inc. J Biomed Mater Res Part A: 104A: 2616-2627, 2016. © 2016 Wiley Periodicals, Inc.

Unicystic ameloblastoma with the presence of dentin

Directory of Open Access Journals (Sweden)

Sivapathasundharam B

2007-01-01

Full Text Available We present a case of unicystic ameloblastoma of the posterior mandible in a 28 year-old female, histologically showing luminal and intramural plexiform epithelial proliferation with typical dentin in the connective tissue capsule. The characteristics of hard tissue formation in ameloblastomas reported in existing literature and the possible origin of the dentin mass seen in our case are discussed.

Experimental resin cements containing bioactive fillers reduce matrix metalloproteinase-mediated dentin collagen degradation.

Science.gov (United States)

Osorio, Raquel; Yamauti, Monica; Sauro, Salvatore; Watson, Thimoty F; Toledano, Manuel

2012-09-01

Collagen dentin matrix may represent a suitable scaffold to be remineralized in the presence of bioactive materials. The purpose of this study was to determine if experimental resin cements containing bioactive fillers may modulate matrix metalloproteinase-mediated collagen degradation of etched dentin. Human dentin beams demineralized using 10% phosphoric acid or 0.5 mol/L EDTA were infiltrated with the following experimental resins: (1) unfilled resin, (2) resin with Bioglass 45S5 particles (Sylc; OSspray Ltd, London, UK), and (3) resin with β-tricalcium phosphate-modified calcium silicate cement (HCAT-β) particles. The filler/resin ratio was 40/60 wt%. The specimens were stored in artificial saliva, and the determination of C-terminal telopeptide (ICTP) was performed by radioimmunoassay after 24 hours, 1 week, and 4 weeks. Scanning electron microscopic analysis of dentin surfaces after 4 weeks of storage was also executed. Collagen degradation was prominent both in phosphoric acid and EDTA-treated dentin. Resin infiltration strongly reduced the MMP activity in demineralized dentin. Resin-containing Bioglass 45S5 particles exerted higher and more stable protection of collagen at all tested dentin states and time points. HCAT-β induced collagen protection from MMPs only in EDTA-treated specimens. Dentin remineralization was achieved when dentin was infiltrated with the resin cements containing bioactive fillers. MMP degradation of dentin collagen is strongly reduced in resin-infiltrated dentin. The inclusion of Bioglass 45S5 particles exerted an additional protection of collagen during dentin remineralization. Copyright © 2012 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Hipótesis actuales relacionadas con la sensibilidad dentinal

Directory of Open Access Journals (Sweden)

Andrés Pérez Ruiz

1999-08-01

Full Text Available Se hace una revisión sobre las hipótesis actuales concernientes a la sensibilidad dentinal, centrando el análisis en las teorías acerca de la presencia de nervios en la dentina, la transmisión del impulso nervioso mediante el odontoblasto y el movimiento de fluidos dentro de la dentina. Por ser la explicación de la sensibilidad de la dentina uno de los más complejos problemas de la fisiología y la histología del diente, se exponen los hechos morfológicos y funcionales que apoyan la validez de los mecanismos mencionados. Se concluye que aunque la teoría hidrodinámica tiene una sólida base experimental y es la de mayor aceptación en la actualidad, pudieran estar involucrados en la génesis del dolor dentinal más de una de estas explicaciones probables.A review of the present hypotheses of dentinal sensitivity was carried out. The analysis was centered on the theories of the existance of nerves in dentin, the transfer of nervous impulse through odontoblast and the fluid flow in the dentin. Since the explanation of dentin sensitivity is one of the most complex problems of dental physiology and histology; the morphological and functional aspects that support the validity of the mentioned mechanisms are stated. It is concluded that although the hydrodynamic theory has a sound experimental basis and is widely accepted at present, more than one of these likely theories could be involved in the genesis of dentinal pain.

Dentin-Composite Bond Strength Measurement Using the Brazilian Disk Test

Science.gov (United States)

Carrera, Carola A.; Chen, Yung-Chung; Li, Yuping; Rudney, Joel; Aparicio, Conrado; Fok, Alex

2016-01-01

Objectives This study presents a variant of the Brazilian disk test (BDT) for assessing the bond strength between composite resins and dentin. Methods Dentin-composite disks (φ 5 mm × 2 mm) were prepared using either Z100 or Z250 (3M ESPE) in combination with one of three adhesives, Adper Easy Bond (EB), Adper Scotchbond Multi-Purpose (MP) and Adper Single Bond (SB), and tested under diametral compression. Acoustic emission (AE) and digital image correlation (DIC) were used to monitor debonding of the composite from the dentin ring. A finite element (FE) model was created to calculate the bond strengths using the failure loads. Fracture modes were examined by scanning electron microscopy (SEM). Results Most specimens fractured along the dentin-resin composite interface. DIC and AE confirmed interfacial debonding immediately before fracture of the dentin ring. Results showed that the mean bond strength with EB (14.9±1.9 MPa) was significantly higher than with MP (13.2±2.4 MPa) or SB (12.9±3.0 MPa) (p0.05). Z100 (14.5±2.3 MPa) showed higher bond strength than Z250 (12.7±2.5 MPa) (padhesive failure mode. EB failed mostly at the dentin-adhesive interface, whereas MP at the composite-adhesive interface; specimens with SB failed at the composite-adhesive interface and cohesively in the adhesive. Conclusions The BDT variant showed to be a suitable alternative for measuring the bond strength between dentin and composite, with zero premature failure, reduced variability in the measurements, and consistent failure at the dentin-composite interface. PMID:27395367

Glutaraldehyde-induced remineralization improves the mechanical properties and biostability of dentin collagen

Energy Technology Data Exchange (ETDEWEB)

Chen, Chaoqun; Mao, Caiyun; Sun, Jian; Chen, Yi; Wang, Wei [Department of Stomatology, The First Affiliated Hospital, College of Medicine, Zhejiang University (China); Pan, Haihua; Tang, Ruikang [Centre for Biopathways and Biomaterials, Department of Chemistry, Zhejiang University (China); Gu, Xinhua [Department of Stomatology, The First Affiliated Hospital, College of Medicine, Zhejiang University (China)

2016-10-01

The purpose of this study was to induce a biomimetic remineralization process by using glutaraldehyde (GA) to reconstruct the mechanical properties and biostability of demineralized collagen. Demineralized dentin disks (35% phosphoric acid, 10 s) were pretreated with a 5% GA solution for 3 min and then cultivated in a calcium phosphate remineralization solution. The remineralization kinetics and superstructure of the remineralization layer were evaluated by Raman spectroscopy, transmission electron microscopy, scanning electron microscopy and nanoindentation tests. The biostability was examined by enzymatic degradation experiments. A significant difference was found in dentin remineralization process between dentin with and without GA pretreating. GA showed a specific affinity to dentin collagen resulting in the formation of a cross-linking superstructure. GA pretreating could remarkably shorten remineralization time from 7 days to 2 days. The GA-induced remineralized collagen fibrils were well encapsulated by newly formed hydroxyapatite mineral nanocrystals. With the nano-hydroxyapatite coating, both the mechanical properties (elastic modulus and hardness) and the biostability against enzymatic degradation of the collagen were significantly enhanced, matching those of natural dentin. The results indicated that GA cross-linking of dentin collagen could promote dentin biomimetic remineralization, resulting in an improved mechanical properties and biostability. It may provide a promising tissue-engineering technology for dentin repair. - Highlights: • GA cross-linking can promote the remineralization kinetics of dentin collagen. • GA-induced remineralization can reshape the demineralized dentin collagen layer. • The GA-induced remineralization enhances the degradation resistance of collagen. • GA-induced remineralization provides a new approach to improve bonding durability.

Glutaraldehyde-induced remineralization improves the mechanical properties and biostability of dentin collagen

International Nuclear Information System (INIS)

Chen, Chaoqun; Mao, Caiyun; Sun, Jian; Chen, Yi; Wang, Wei; Pan, Haihua; Tang, Ruikang; Gu, Xinhua

2016-01-01

The purpose of this study was to induce a biomimetic remineralization process by using glutaraldehyde (GA) to reconstruct the mechanical properties and biostability of demineralized collagen. Demineralized dentin disks (35% phosphoric acid, 10 s) were pretreated with a 5% GA solution for 3 min and then cultivated in a calcium phosphate remineralization solution. The remineralization kinetics and superstructure of the remineralization layer were evaluated by Raman spectroscopy, transmission electron microscopy, scanning electron microscopy and nanoindentation tests. The biostability was examined by enzymatic degradation experiments. A significant difference was found in dentin remineralization process between dentin with and without GA pretreating. GA showed a specific affinity to dentin collagen resulting in the formation of a cross-linking superstructure. GA pretreating could remarkably shorten remineralization time from 7 days to 2 days. The GA-induced remineralized collagen fibrils were well encapsulated by newly formed hydroxyapatite mineral nanocrystals. With the nano-hydroxyapatite coating, both the mechanical properties (elastic modulus and hardness) and the biostability against enzymatic degradation of the collagen were significantly enhanced, matching those of natural dentin. The results indicated that GA cross-linking of dentin collagen could promote dentin biomimetic remineralization, resulting in an improved mechanical properties and biostability. It may provide a promising tissue-engineering technology for dentin repair. - Highlights: • GA cross-linking can promote the remineralization kinetics of dentin collagen. • GA-induced remineralization can reshape the demineralized dentin collagen layer. • The GA-induced remineralization enhances the degradation resistance of collagen. • GA-induced remineralization provides a new approach to improve bonding durability.

Microtensile bond strength of three simplified adhesive systems to caries-affected dentin.

Science.gov (United States)

Scholtanus, J D; Purwanta, Kenny; Dogan, Nilgun; Kleverlaan, Cees J; Feilzer, Albert J

2010-08-01

The purpose of the study was to determine the microtensile bond strength of three different simplified adhesive systems to caries-affected dentin. Fifteen extracted human molars with primary carious lesions were ground flat until dentin was exposed. Soft caries-infected dentin was excavated with the help of caries detector dye. On the remaining hard dentin, a standardized smear layer was created by polishing with 600-grit SiC paper. Teeth were divided into three groups and treated with one of the three tested adhesives: Adper Scotchbond 1 XT (3M ESPE), a 2-step etch-andrinse adhesive, Clearfil S3 Bond (Kuraray), a 1-step self-etching or all-in-one adhesive, and Clearfil SE Bond (Kuraray), a 2-step self-etching adhesive. Five-mm-thick composite buildups (Z-250, 3M ESPE) were built and light cured. After water storage for 24 h at 37ºC, the bonded specimens were sectioned into bars (1.0 x 1.0 mm; n = 20 to 30). Microtensile bond strength of normal dentin specimens and caries-affected dentin specimens was measured in a universal testing machine (crosshead speed = 1 mm/min). Data were analyzed using two-way ANOVA and Tukey's post-hoc test (p adhesives were found. Adper Scotchbond 1 XT and Clearfil S3 Bond showed significantly lower bond strength values to caries-affected dentin. For Clearfil SE Bond, bond strength values to normal and caries-affected dentin were not significantly different. All the tested simplified adhesives showed similar bond strength values to normal dentin. For the tested 2-step etch-and-rinse adhesive and the all-in-one adhesive, the bond strength values to caries-affected dentin were lower than to normal dentin.

Fracture mechanism of coronal teenage dentin

Science.gov (United States)

Panfilov, P. E.; Kabanova, A. V.; Borodin, I. N.; Guo, J.; Zang, Z.

2017-10-01

The structure of coronal teenage dentin and the development of cracks in it are studied on microand nanolevels. The material is found to fail according to a ductile mechanism on a microlelvel and according to a ductile-brittle mechanism on a nanoscale. This behavior is similar to the failure of a polyethylene film and rubber, when significant elastic and irreversible deformation precedes crack growth. The viscoelastic behavior can be considered as the reaction of dentin to an applied mechanical load.

Structure and microstructure of coronary dentin in non-erupted human deciduous incisor teeth

Directory of Open Access Journals (Sweden)

Costa Luciane R.R S.

2002-01-01

Full Text Available The dentin structure of non-erupted human deciduous mandibular and maxillary central and lateral incisor teeth was studied employing light and scanning electron microscopy. For light microscopy, nitric-acid-demineralized and ground sections were used. The sections were stained by hematoxylin-eosin, picrosirius and azo-carmim methods, and ground specimens were prepared using a carborundum disk mounted in a handpiece. For SEM study, teeth were frozen in liquid nitrogen and fractured at longitudinal and transversal directions. Structurally, demineralization and ground methods revealed tubules with primary and secondary curvatures, canaliculi, giant tubules, interglobular dentin, predentin, and intertubular dentin. Scanning electron microscopy showed three-dimensional aspects of dentinal tubules, canaliculi, peritubular dentin, intertubular dentin, and predentin. This study contributes to knowledge about dentin morphology showing characteristics of teeth not yet submitted to mastication stress.

Current Advance and Future Prospects of Tissue Engineering Approach to Dentin/Pulp Regenerative Therapy

Directory of Open Access Journals (Sweden)

Ting Gong

2016-01-01

Full Text Available Recent advances in biomaterial science and tissue engineering technology have greatly spurred the development of regenerative endodontics. This has led to a paradigm shift in endodontic treatment from simply filling the root canal systems with biologically inert materials to restoring the infected dental pulp with functional replacement tissues. Currently, cell transplantation has gained increasing attention as a scientifically valid method for dentin-pulp complex regeneration. This multidisciplinary approach which involves the interplay of three key elements of tissue engineering—stem cells, scaffolds, and signaling molecules—has produced an impressive number of favorable outcomes in preclinical animal studies. Nevertheless, many practical hurdles need to be overcome prior to its application in clinical settings. Apart from the potential health risks of immunological rejection and pathogenic transmission, the lack of a well-established banking system for the isolation and storage of dental-derived stem cells is the most pressing issue that awaits resolution and the properties of supportive scaffold materials vary across different studies and remain inconsistent. This review critically examines the classic triad of tissue engineering utilized in current regenerative endodontics and summarizes the possible techniques developed for dentin/pulp regeneration.

Current Advance and Future Prospects of Tissue Engineering Approach to Dentin/Pulp Regenerative Therapy

Science.gov (United States)

Gong, Ting; Heng, Boon Chin; Lo, Edward Chin Man; Zhang, Chengfei

2016-01-01

Recent advances in biomaterial science and tissue engineering technology have greatly spurred the development of regenerative endodontics. This has led to a paradigm shift in endodontic treatment from simply filling the root canal systems with biologically inert materials to restoring the infected dental pulp with functional replacement tissues. Currently, cell transplantation has gained increasing attention as a scientifically valid method for dentin-pulp complex regeneration. This multidisciplinary approach which involves the interplay of three key elements of tissue engineering—stem cells, scaffolds, and signaling molecules—has produced an impressive number of favorable outcomes in preclinical animal studies. Nevertheless, many practical hurdles need to be overcome prior to its application in clinical settings. Apart from the potential health risks of immunological rejection and pathogenic transmission, the lack of a well-established banking system for the isolation and storage of dental-derived stem cells is the most pressing issue that awaits resolution and the properties of supportive scaffold materials vary across different studies and remain inconsistent. This review critically examines the classic triad of tissue engineering utilized in current regenerative endodontics and summarizes the possible techniques developed for dentin/pulp regeneration. PMID:27069484

Polymerization contraction stress in dentin adhesives bonded to dentin and enamel

NARCIS (Netherlands)

Hashimoto, M.; de Gee, A.J.; Feilzer, A.J.

2008-01-01

Objective In a previous study on of polymerization contraction stress determinations of adhesives bonded to dentin a continuous decline of stress was observed after the adhesives had been light-cured. The decline was ascribed to stress relief caused by diffusion into the adhesive layer of water

Effect of Dentin Wetness on the Bond Strength of Universal Adhesives

Directory of Open Access Journals (Sweden)

An-Na Choi