Uranium, a factor limiting nuclear energy?

International Nuclear Information System (INIS)

Ohnemus, J.

2006-01-01

Nuclear power has been back as a topic of public debate since early this year. A special subject under discussion is the extension of nuclear power plant life. Hardly had it been on the agenda, when interested parties announced that this step was impossible because uranium reserves were no longer sufficient. A variety of terms are being used in this discussion without their meaning being taken into account: stocks, resources, and reserves. To clarify the situation, this article outlines important aspects of short and long term uranium supplies, and analyzes their meaning. Here are some of the most important issues under consideration: - For what period of time is there really enough uranium? - Is uranium becoming the limiting factor in the use of nuclear power? - Is uranium really a 'sustainable' energy resource? - Will higher prices extend the range? - What is the influence of the price of uranium on the cost of electricity generation? Among other results, it is found that comprehensive sources of low-price uranium and nuclear fuels are, or can be made, available worldwide. Consequently, the 'range' is beyond the time frames currently mentioned, also as a function of technological factors, i.e. reaching several hundred years. It is also important to note that nuclear power - ensures greater independence of volatile imported sources, - guarantees reliably low electricity prices, - has a huge potential of environmental protection, and - is a clean source of energy. (orig.)

Uranium, a factor limiting nuclear energy?

International Nuclear Information System (INIS)

2006-01-01

Nuclear power has been back as a topic of public debate since early this year. A special subject under discussion is the extension of nuclear power plant life. Hardly had it been on the agenda, when interested parties announced that this step was impossible because uranium reserves were no longer sufficient. A variety of terms are being used in this discussion without their meaning being taken into account: stocks, resources, and reserves. To clarify the situation, this article outlines important aspects of short and long term uranium supplies, and analyzes their meaning. Here are some of the most important issues under consideration: - For what period of time is there really enough uranium? - Is uranium becoming the limiting factor in the use of nuclear power? - Is uranium really a 'sustainable' energy resource? - Will higher prices extend the range? - What is the influence of the price of uranium on the cost of electricity generation? Among other results, it is found that comprehensive sources of low-price uranium and nuclear fuels are, or can be made, available worldwide. Consequently, the 'range' is beyond the time frames currently mentioned, also as a function of technological factors, i.e. reaching several hundred years. It is also important to note that nuclear power - ensures greater independence of volatile imported sources, - guarantees reliably low electricity prices, - has a huge potential of environmental protection, and - is a clean source of energy. (orig./GL)

Uranium - a factor limiting nuclear energy?

International Nuclear Information System (INIS)

Ohnemus, J.

2006-01-01

Nuclear power has been back as a topic of public debate since early this year. A special subject under discussion is the extension of nuclear power plant life. Hardly had it been on the agenda, when interested parties announced that this st ep was impossible because uranium reserves were no longer sufficient. A variety of terms are being used in this discussion without their meaning being taken int o account: stocks, resources, and reserves. To clarify the situation, this artic le outlines important aspects of short and long term uranium supplies, and analy zes their meaning. Here are some of the most important issues under consideration: - For what period of time is there really enough uranium? - Is uranium becoming the limiting factor in the use of nuclear power? - Is uranium really a 'sustainable' energy resource? - Will higher prices extend the range? - What is the in fluence of the price of uranium on the cost of electricity generation? Among oth er results, it is found that comprehensive sources of low-price uranium and nucl ear fuels are, or can be made, available worldwide. Consequently, the 'range' is beyond the time frames currently mentioned, also as a function of technological factors, i.e. reaching several hundred years. It is also important to note that nuclear power - ensures greater independence of volatile imported sources, - guarantees reliably low electricity prices, - has a huge potential of environmental protection, and - is a clean source of energy. (orig.)

Risk assessment applications for determining cleanup limits for uranium in treated and untreated soils

International Nuclear Information System (INIS)

Armstrong, A.Q.; Layton, D.W.; Rutz, E.E.

1994-01-01

Uranium-contaminated soils are present at various locations across the US where uranium was processed for nuclear fuels or atomic weapons. Important issues relative to such contamination include the assessment of potential health risks associated with human exposures to the residual uranium and the determination of safe levels of uranium in soils that have been treated by a given technology. This paper discusses various risk assessment considerations that must be dealt with when developing cleanup limits for uranium in treated and untreated soils. Key issues addressed include alternative land use scenarios, potential exposure pathways, characterization of the bioavailability of uranium compounds in food and water, a brief overview of health risks associated with uranium and its daughter products as well as a summary of considerations for development of risk-based cleanup limits for uranium in soils

Here's health, U workers

International Nuclear Information System (INIS)

Swiegers, W.R.S.

1987-01-01

It was decided to embark on an occupational health research program at Roessing Uranium Mine because there was a real need for a well-planned prospective epidemiological study which could contribute towards the better understanding of the etiology and natural history of occupational diseases. The main objective of this study is to correlate the respiratory health status in relation to occupational exposure and smoking in a uranium mining and milling environment

Derived surface contamination limits for the uranium mining and milling industry

International Nuclear Information System (INIS)

Ching, S.H.

1984-10-01

Derived Surface Contamination Limits (DSCL) are proposed for the control of surface contamination at the work place for the uranium mining and milling industry. They have been derived by a method incorporating recent ICRP recommendations and consideration of the radiation exposure pathways of ingestion, inhalation and external irradiation of the basal layer of skin. A generalized DSCL of 10 5 Bq/m 2 of beta activity is recommended for all contaminants likely to be found in uranium mine and mill workplaces except for fresh uranium concentrates. In the latter case, the DSCL is expressed in terms of alpha activity because the ratio of beta to alpha activities for fresh uranium concentrates is variable; the beta activity increases with the ingrowth of U-238 daughter products (Th-234 and Pa-234m) until secular equilibrium is re-established in about six months. A surface contamination limit of 10 4 Bq/m 2 of beta activity is proposed for the release of non-porous materials and equipment with no detectable loose contamination to the public domain

Solubility Limits of Dibutyl Phosphoric Acid in Uranium Solutions at SRS

International Nuclear Information System (INIS)

Thompson, M.C.; Pierce, R.A.; Ray, R.J.

1998-06-01

The Savannah River Site has enriched uranium (EU) solution which has been stored for almost 10 years since being purified in the second uranium cycle of the H area solvent extraction process. The concentrations in solution are 6 g/L U and about 0.1 M nitric acid. Residual tributylphosphate in the solutions has slowly hydrolyzed to form dibutyl phosphoric acid (HDBP) at concentrations averaging 50 mg/L. Uranium is known to form compounds with DBP which have limited solubility. The potential to form uranium-DBP solids raises a nuclear criticality safety issue. SRTC tests have shown that U-DBP solids will precipitate at concentrations potentially attainable during storage of enriched uranium solutions. Evaporation of the existing EUS solution without additional acidification could result in the precipitation of U-DBP solids if DBP concentration in the resulting solution exceeds 110 ppm at ambient temperature. The same potential exists for evaporation of unwashed 1CU solutions. The most important variables of interest for present plant operations are HNO 3 and DBP concentrations. Temperature is also an important variable controlling precipitation. The data obtained in these tests can be used to set operating and safety limits for the plant. It is recommended that the data for 0 degrees C with 0.5 M HNO 3 be used for setting the limits. The limit would be 80 mg/L which is 3 standard deviations below the average of 86 observed in the tests. The data shows that super-saturation can occur when the DBP concentration is as much as 50 percent above the solubility limit. However, super-saturation cannot be relied on for maintaining nuclear criticality safety. The analytical method for determining DBP concentration in U solutions was improved so that analyses for a solution are accurate to within 10 percent. However, the overall uncertainty of results for periodic samples of the existing EUS solutions was only reduced slightly. Thus, sampling appears to be the largest portion

Limits for the release of uranium compounds to the environment

International Nuclear Information System (INIS)

Lopez, F.; Ferruz, P.; Aguayo, A.

1987-01-01

A conservative criteria to be be followed by a Regulatory Body, in order to provide the limits of radioactive material release in the environment, When all the parameters are not available for the optimization of radiation protection is presented. This criteria can be applied to stablishment of radioactive release limits for uranium compounds from the nuclear fuel cycle facilities. (author)

Past exposure

International Nuclear Information System (INIS)

Dropkin, G.; Clark, D.

1992-01-01

Past Exposure uses confidential company documents, obtained by the Namibia Support Committee over several years, to draw attention to risks to workers' health and the environment at Roessing Uranium mine. Particular reference is made to discussion of dust levels, radiation hazards, uranium poisoning, environmental leaks, especially from the tailings dam, and the lack of monitoring of thorium. In relation to agreements between trades unions and mines, agreements reached by RTZ-owned Canadian in Canada, and British Nuclear Fuels in the UK, are discussed. (UK)

Generally applicable limits on intakes of uranium based on its chemical toxicity and the radiological significance of intakes at those limits

International Nuclear Information System (INIS)

Thorne, M C; Wilson, J

2015-01-01

Uranium is chemically toxic and radioactive, and both considerations have to be taken into account when limiting intakes of the element, in the context of both occupational and public exposures. Herein, the most recent information available on the chemical toxicity and biokinetics of uranium is used to propose new standards for limiting intakes of the element. The approach adopted allows coherent standards to be set for ingestion and inhalation of different chemical forms of the element by various age groups. It also allows coherent standards to be set for occupational and public exposures (including exposures of different age groups) and for various exposure regimes (including short-term and chronic exposures). The proposed standards are more restrictive than those used previously, but are less restrictive than the Minimal Risk Levels proposed recently by the US Agency for Toxic Substances and Disease Registry. Having developed a set of proposed limits based solely on chemical toxicity considerations, the radiological implications of exposure at those proposed limits are investigated for natural, depleted and enriched uranium. (paper)

Meeting of the French geological society - Uranium: geology, geophysics, chemistry. Book of abstracts; Reunion de la Societe Geologique de France - Uranium: geologie, geophysique, chimie. Recueil des resumes

Energy Technology Data Exchange (ETDEWEB)

Zakari, A.A.; Mima, S.; Bidaud, A.; Criqui, P.; Menanteau, P.; David, S.; Pagel, M.; Chagnes, A.; Cote, G.; Courtaud, B.; Thiry, J.; Miehe, J.M.; Gilbert, F.; Cuney, M.; Bruneton, P.; Ewington, D.; Vautrin-Ul, C.; Cannizzo, C.; Betelu, S.; Chausse, A.; Ly, J.; Bourgeois, D.; Maynadie, J.; Meyer, D.; Clavier, N.; Costin, D.T.; Cretaz, F.; Szenknect, S.; Ravaux, J.; Poinssot, C.; Dacheux, N.; Durupt, N.; Blanvillain, J.J.; Geffroy, F.; Aparicio, B.; Dubessy, J.; Nguyen-Trung, C.; Robert, P.; Uri, F.; Beaufort, D.; Lescuyer, J.L.; Morichon, E.; Allard, T.; Milesi, J.P.; Richard, A.; Rozsypal, C.; Mercadier, J.; Banks, D.A.; Boiron, M.C.; Cathelineau, M.; Dardel, J.; Billon, S.; Patrier, P.; Wattinne, A.; Vanderhaeghe, O.; Fabre, C.; Castillo, M.; Salvi, S.; Beziat, D.; Williams-Jones, A.E.; Trap, P.; Durand, C.; Goncalves, P.; Marquer, D.; Feybesse, J.L.; Richard, Y.; Orberger, B.; Hofmann, A.; Megneng, M.; Orberger, B.; Bouttemy, M.; Vigneron, J.; Etcheberry, A.; Perdicakis, M.; Prignon, N.; Toe, W.; Andre-Mayer, A.S.; Eglinger, A.; Jordaan, T.; Hocquet, S.; Ledru, P.; Selezneva, V.; Vendryes, G.; Lach, P.; Cuney, M.; Mercadier, J.; Brouand, M.; Duran, C.; Seydoux-Guillaume, A.M.; Bingen, B.; Parseval, P. de; Guillaume, D.; Bosse, V.; Paquette, J.L.; Ingrin, J.; Montel, J.M.; Giot, R.; Maucotel, F.; Hubert, S.; Gautheron, C.; Tassan-Got, L.; Pagel, M.; Barbarand, J.; Cuney, M.; Lach, P.; Bonhoure, J.; Leisen, M.; Kister, P.; Salaun, A.; Villemant, B.; Gerard, M.; Komorowski, J.C.; Michel, A.; Riegler, T.; Tartese, R.; Boulvais, P.; Poujols, M.; Gloaguen, E.; Mazzanti, M.; Mougel, V.; Nocton, G.; Biswas, B.; Pecaut, J.; Othmane, G.; Menguy, N.; Vercouter, T.; Morin, G.; Galoisy, L.; Calas, G.; Fayek, M.

2010-11-15

-temperature, and metallogenic provinces; 21 - Magmatic-hydrothermal transition in the Roessing pegmatite: implications for uranium mineralisation; 22 - Deformation and partial fusion of a Archean-paleo-Proterozoic crust: implication on uraniferous ores mobilization and deposition, Torngats orogenesis, Ungava bay; 23 - Black chert pebbles of the Pongola basin conglomerates ({approx}2, 9 Ga - South Africa): a potential uranium source?; 24 - origin and evolution of detrital pyrites in meso-Archean conglomerates (3.08-2.64 Ga) of South Africa: uranium source or trap?; 25 - Experimental study of U(VI) carbonates with respect to 3 parameters: pH, carbonate concentration, temperature, using vibrational (Raman, FTIR, ATR) and optical (UV-visible) spectroscopy; 26 - Nature and significance of the contact between the Abbabis gneiss complex and the meta-sedimentary sequences of the Damara orogenic belt; 27 - Metallogenic potentialities of Proterozoic orogenic belts accreted to Archean basements: the Damara/Lufilien orogen - Namibia and Zambia; 28 - Contribution of the Geological Exploration to the development of the KATCO ISR mine - Chu-Sarysu basin, Kazakhstan; 29 - Remarks about some remarkable events which occurred during the Francevillien formation; 30 - Geochemical signature of different mineral phases obtained by ICP-MS laser ablation (trace elements and rare earths): Application Uranium deposits; 31 - Role of fluids and irradiation in complex pegmatite euxenite/zircon assemblies from Norway and their U-Pb geochronological consequences; 32 - Mechanical modeling of rupture around metamictic minerals; 33 - Helium diffusion in apatite: Effect alpha recoil-linked damages; 34 - Rare earth spectra in uranium oxides: a marker of the uranium deposit type; 35 - Rare earths: tracers of uranium behaviour during acid sulphated hydrothermal weathering - the Guadeloupe example; 36 - What metallogenic model for the Kiggavik-Andrew Lake trend? Nunavut, Canada; 37 - Uranium mobility in the Southern

Derivation of release limits for a typical uranium mining and milling facility

International Nuclear Information System (INIS)

1985-09-01

This report develops guidelines for calculating derived release limits (DRLs) for releases of each radionuclide belonging to the uranium-238 and thorium-232 decay chains to atmosphere, surface water and groundwater from uranium mining and milling operations in Canada. DRLs are defined as calculated limits on releases from the facility that result in radiation exposures through all environmental pathways equal to the annual effective dose equivalent limit of 0.005 Sv for stochastic effects or the annual dose equivalent limit of 0.05 Sv for non-stochastic effects in the critical group. By definition, DRLs apply to controllable radionuclide emissions which occur during the operational phase of mine/mill facilities. The report develops a steady-state environmental transfer model to determine environmental dilution and dispersion in atmosphere, surface water and groundwater between the sources at the mine and mill and the critical group receptor. Exposure pathways incorporated in the model include external exposure from immersion in the airborne plume, immersion in water, contaminated ground and contaminated shoreline sediments. Internal exposure pathways include inhalation of contaminated air and ingestion of contaminated water and terrestrial and aquatic foods

Meeting of the French geological society - Uranium: geology, geophysics, chemistry. Book of abstracts

International Nuclear Information System (INIS)

Zakari, A.A.; Mima, S.; Bidaud, A.; Criqui, P.; Menanteau, P.; David, S.; Pagel, M.; Chagnes, A.; Cote, G.; Courtaud, B.; Thiry, J.; Miehe, J.M.; Gilbert, F.; Cuney, M.; Bruneton, P.; Ewington, D.; Vautrin-Ul, C.; Cannizzo, C.; Betelu, S.; Chausse, A.; Ly, J.; Bourgeois, D.; Maynadie, J.; Meyer, D.; Clavier, N.; Costin, D.T.; Cretaz, F.; Szenknect, S.; Ravaux, J.; Poinssot, C.; Dacheux, N.; Durupt, N.; Blanvillain, J.J.; Geffroy, F.; Aparicio, B.; Dubessy, J.; Nguyen-Trung, C.; Robert, P.; Uri, F.; Beaufort, D.; Lescuyer, J.L.; Morichon, E.; Allard, T.; Milesi, J.P.; Richard, A.; Rozsypal, C.; Mercadier, J.; Banks, D.A.; Boiron, M.C.; Cathelineau, M.; Dardel, J.; Billon, S.; Patrier, P.; Wattinne, A.; Vanderhaeghe, O.; Fabre, C.; Castillo, M.; Salvi, S.; Beziat, D.; Williams-Jones, A.E.; Trap, P.; Durand, C.; Goncalves, P.; Marquer, D.; Feybesse, J.L.; Richard, Y.; Orberger, B.; Hofmann, A.; Megneng, M.; Orberger, B.; Bouttemy, M.; Vigneron, J.; Etcheberry, A.; Perdicakis, M.; Prignon, N.; Toe, W.; Andre-Mayer, A.S.; Eglinger, A.; Jordaan, T.; Hocquet, S.; Ledru, P.; Selezneva, V.; Vendryes, G.; Lach, P.; Cuney, M.; Mercadier, J.; Brouand, M.; Duran, C.; Seydoux-Guillaume, A.M.; Bingen, B.; Parseval, P. de; Guillaume, D.; Bosse, V.; Paquette, J.L.; Ingrin, J.; Montel, J.M.; Giot, R.; Maucotel, F.; Hubert, S.; Gautheron, C.; Tassan-Got, L.; Pagel, M.; Barbarand, J.; Cuney, M.; Lach, P.; Bonhoure, J.; Leisen, M.; Kister, P.; Salaun, A.; Villemant, B.; Gerard, M.; Komorowski, J.C.; Michel, A.; Riegler, T.; Tartese, R.; Boulvais, P.; Poujols, M.; Gloaguen, E.; Mazzanti, M.; Mougel, V.; Nocton, G.; Biswas, B.; Pecaut, J.; Othmane, G.; Menguy, N.; Vercouter, T.; Morin, G.; Galoisy, L.; Calas, G.; Fayek, M.

2010-11-01

-temperature, and metallogenic provinces; 21 - Magmatic-hydrothermal transition in the Roessing pegmatite: implications for uranium mineralisation; 22 - Deformation and partial fusion of a Archean-paleo-Proterozoic crust: implication on uraniferous ores mobilization and deposition, Torngats orogenesis, Ungava bay; 23 - Black chert pebbles of the Pongola basin conglomerates (∼2, 9 Ga - South Africa): a potential uranium source?; 24 - origin and evolution of detrital pyrites in meso-Archean conglomerates (3.08-2.64 Ga) of South Africa: uranium source or trap?; 25 - Experimental study of U(VI) carbonates with respect to 3 parameters: pH, carbonate concentration, temperature, using vibrational (Raman, FTIR, ATR) and optical (UV-visible) spectroscopy; 26 - Nature and significance of the contact between the Abbabis gneiss complex and the meta-sedimentary sequences of the Damara orogenic belt; 27 - Metallogenic potentialities of Proterozoic orogenic belts accreted to Archean basements: the Damara/Lufilien orogen - Namibia and Zambia; 28 - Contribution of the Geological Exploration to the development of the KATCO ISR mine - Chu-Sarysu basin, Kazakhstan; 29 - Remarks about some remarkable events which occurred during the Francevillien formation; 30 - Geochemical signature of different mineral phases obtained by ICP-MS laser ablation (trace elements and rare earths): Application Uranium deposits; 31 - Role of fluids and irradiation in complex pegmatite euxenite/zircon assemblies from Norway and their U-Pb geochronological consequences; 32 - Mechanical modeling of rupture around metamictic minerals; 33 - Helium diffusion in apatite: Effect alpha recoil-linked damages; 34 - Rare earth spectra in uranium oxides: a marker of the uranium deposit type; 35 - Rare earths: tracers of uranium behaviour during acid sulphated hydrothermal weathering - the Guadeloupe example; 36 - What metallogenic model for the Kiggavik-Andrew Lake trend? Nunavut, Canada; 37 - Uranium mobility in the Southern

Control from the bridge

International Nuclear Information System (INIS)

Kesler, S.B.

1986-01-01

To improve the efficiency and to cut down on cost at the uranium mine at Roessing in SWA/Namibia, the control of all the various plants in the complex has been concentrated in one centralised control system. The processing of uranium ores is also discussed. The selection of future operators of the control system was made at the start of the project. Considerable effort went into conceptualising the role and skill requirements for their job, as well as into their training. The project was concluded in 1984. The original hardware installed in the central room was configured with two basic operating stations controlling the Uranium Plant and an additional station controlling the Acid Plant. Since full implementation of the central process control system, the uranium recovery has been significantly increased whilst tighter control of process parameters has enabled reductions to be made in consumable and utilities usage

Felsic magmatism and uranium deposits

International Nuclear Information System (INIS)

Cuney, Michel

2014-01-01

also a favorable uranium source if a large part of the U is hosted in the glassy matrix. The largest U deposit in the world, Olympic Dam in South Australia is hosted by highly fractionated high-K plutonic and volcanic rocks, but the origin of the U mineralization is still unclear. Anatectic pegmatoids containing disseminated uraninite which results from the partial melting of uranium-rich metasediments and/or meta-volcanic felsic rocks, host large low grade U deposits such as the Roessing and Husab deposits in Namibia. The evaluation of the potentiality for igneous rocks to represent an efficient U source represents a critical step to consider during the early stages of exploration for most U deposit types. In particular a wider use of the magmatic inclusions to determine the parent magma chemistry and its U content is of utmost interest to evaluate the U source potential of sedimentary basins that contain felsic volcanic acidic tuffs. (author)

Uranium health physics

International Nuclear Information System (INIS)

1980-01-01

This report contains the papers delivered at the Summer School on Uranium Health Physics held in Pretoria on the 14 and 15 April 1980. The following topics were discussed: uranium producton in South Africa; radiation physics; internal dosimetry and radiotoxicity of long-lived uranium isotopes; uranium monitoring; operational experience on uranium monitoring; dosimetry and radiotoxicity of inhaled radon daughters; occupational limits for inhalation of radon-222, radon-220 and their short-lived daughters; radon monitoring techniques; radon daughter dosimeters; operational experience on radon monitoring; and uranium mill tailings management

Analytical method of uranium (IV) and uranium (VI) in uranium ores and uranium-bearing rocks

International Nuclear Information System (INIS)

Shen Zhuqin; Zheng Yongfeng; Li Qingzhen; Zhong Miaolan; Gu Dingxiang

1995-11-01

The best conditions for keeping the original valences of uranium during the dissolution and separation procedure of geological samples (especially those micro uranium-bearing rock) were studied. With the exist of high concentration protectants, the sample was decomposed with concentration HF at 40 +- 5 degree C. The U(VI) was dissolved completely and formed stable complex UO 2 F 2 , the U(IV) was precipitated rapidly and carried by carrier. Quantitative separation was carried out immediately with suction. The decomposition of sample and separation of solid/liquid phases was completed within two minutes. After separation, the U(IV) and U(VI) were determined quantitatively with laser fluorescence or voltametry respectively according to the uranium content. The limit of detection for this method is 0.7 μg/g, RSD is 10.5%, the determinate range of uranium is 2 x 10 -6 ∼10 -1 g/g. The uranium contents and their valence state ratio were measured for more than one hundred samples of sand stone and granite, the accuracy and precision of these results are satisfactory for uranium geological research. (12 tabs.; 11 refs.)

Oxidative Uranium Release from Anoxic Sediments under Diffusion-Limited Conditions.

Science.gov (United States)

Bone, Sharon E; Cahill, Melanie R; Jones, Morris E; Fendorf, Scott; Davis, James; Williams, Kenneth H; Bargar, John R

2017-10-03

Uranium (U) contamination occurs as a result of mining and ore processing; often in alluvial aquifers that contain organic-rich, reduced sediments that accumulate tetravalent U, U(IV). Uranium(IV) is sparingly soluble, but may be mobilized upon exposure to nitrate (NO 3 - ) and oxygen (O 2 ), which become elevated in groundwater due to seasonal fluctuations in the water table. The extent to which oxidative U mobilization can occur depends upon the transport properties of the sediments, the rate of U(IV) oxidation, and the availability of inorganic reductants and organic electron donors that consume oxidants. We investigated the processes governing U release upon exposure of reduced sediments to artificial groundwater containing O 2 or NO 3 - under diffusion-limited conditions. Little U was mobilized during the 85-day reaction, despite rapid diffusion of groundwater within the sediments and the presence of nonuraninite U(IV) species. The production of ferrous iron and sulfide in conjunction with rapid oxidant consumption suggested that the sediments harbored large concentrations of bioavailable organic carbon that fueled anaerobic microbial respiration and stabilized U(IV). Our results suggest that seasonal influxes of O 2 and NO 3 - may cause only localized mobilization of U without leading to export of U from the reducing sediments when ample organic carbon is present.

Derived limits for occupational exposure to uranium mine and mill dusts in the air and on surfaces

International Nuclear Information System (INIS)

Carter, M.W.

1983-01-01

Limits are derived for the concentration of uranium mine and mill dusts in the air based on ICRP30 and assumptions regarding the isotopic make up of the dusts. From these limits using a resuspension factor, limits for surface contamination are derived. Calculations are presented of the dose to the basal layer of the skin from mine and mill dusts on the skin. From these calculations limits for skin contamination are derived. A calculation of a limit based on direct ingestion is also presented. Exposure limits for the public are not considered

Uranium production from low grade Swedish shale

International Nuclear Information System (INIS)

Carlsson, O.

1977-01-01

In view of the present nuclear programmes a steep increase in uranium demand is foreseen which will pose serious problems for the uranium industry. The annual additions to uranium ore reserves must almost triple within the next 15 years in order to support the required production rates. Although there are good prospects for the discovery of further conventional deposits of uranium there is a growing interest in low grade uranium deposits. Large quantities of uranium exist in black shales, phosphates, granites, sea water and other unconventional sources. There are however factors which limit the utilization of these low grade materials. These factors include the extraction costs, the environmental constrains on mining and milling of huge amounts of ore, the development of technologies for the beneficiation of uranium and, in the case of very low grade materials, the energy balance. The availability of by-product uranium is limited by the production rate of the main product. The limitations differ very much according to types of ores, mining and milling methods and the surroundings. As an illustration a description is given of the Swedish Ranstad uranium shale project, its potential, constraints and technical solutions

National uranium resource evaluation, preliminary report

International Nuclear Information System (INIS)

1976-06-01

The results of the initial phase of the National Uranium Resource Evaluation (NURE) are reported. NURE is a comprehensive nationwide program to evaluate uranium resources and to identify areas favorable for uranium exploration. Part I presents estimates of uranium ore reserves and potential resources available at costs (not prices) of $10, $15, and $30 per pound U 3 O 8 (uranium oxide). These estimates comprise the national uranium resource position. They are, however, preliminary because limitations of time and available geologic data prevented adequate assessment of some areas that may be favorable for potential resources. Part II presents the potential uranium resources for each of 13 regions, whose boundaries have been drawn chiefly on geologic considerations. The general geology is summarized, and the types of uranium deposits are described. Although limited geologic reconnaissance was done in various parts of the country, the report is based primarily on the compilation and evaluation of data in ERDA files. Mining companies furnished a substantial amount of information on exploration results, development, production, and future plans. Published, manuscript, and open-file reports by government agencies, universities, and research organizations were reviewed. In addition, many individuals affiliated with universities and with state and federal agencies provided supplemental geologic information. This was particularly helpful in the eastern and central states and in Alaska, where information on uranium occurrences is limited

Uranium in drinking water. A simple determination of uranium (VI) according to DIN standard 38406-17

International Nuclear Information System (INIS)

Haug, Sandro

2009-01-01

The number of reports on uranium loads in tap water and drinking water increases. Already for years, the organization Foodwatch e.V. (Berlin, Federal Republic of Germany) warns about to high concentrations of uranium in tap water. So far, only a limit value for mineral water exists in the Mineral Water Regulation which is suitable for the production of infant diet. This limit value amounts 2 microgram per litre. Temporarily, also in the policy a national limit value for uranium in drinking water is introduced. The Federal Office for Environment Protection (Dessau, FRG) designates a value of ten microgram uranium per litre of drinking water and mineral water as an approximate value. The effective control of water quality presupposes high-performance, simple and economical analysis methods. A particularly well suitable measuring technique for the determination of uranium(VI) in groundwater, raw water and drinking water is the voltammetry. In the last years, a national standard was compiled based on this measuring technique: DIN standard 38406-17

Jabiluka uranium project

International Nuclear Information System (INIS)

Anon.

1991-01-01

The Jabiluka uranium and gold deposit located in the Northern Territory of Australia is the world's largest known primary uranium deposits and as such has the potential to become one of the most important uranium projects in the world. Despite the financial and structural challenges facing the major owner Pancontinental Mining Limited and the changing political policies in Australia, Jabiluka is well situated for development during the 1990's. With the availability of numerous financial and development alternatives, Jabiluka could, by the turn of the century, take its rightful place among the first rank of world uranium producers. The paper discusses ownership, location, property rights, licensing, environmental concerns, marketing and development, capital costs, royalties, uranium policy considerations, geologic exploration history, regional and site geology, and mining and milling operations

Uranium toxicology

International Nuclear Information System (INIS)

Ferreyra, Mariana D.; Suarez Mendez, Sebastian

1997-01-01

In this paper are presented the methods and procedures optimized by the Nuclear Regulatory Authority (ARN) for the determination of: natural uranium mass, activity of enriched uranium in samples of: urine, mucus, filters, filter heads, rinsing waters and Pu in urine, adopted and in some cases adapted, by the Environmental Monitoring and Internal Dosimetry Laboratory. The analyzed material corresponded to biological and environmental samples belonging to the staff professionally exposed that work in plants of the nuclear fuel cycle. For a better comprehension of the activities of this laboratory, it is included a brief description of the uranium radiochemical toxicity and the limits internationally fixed to preserve the workers health

Formation conditions for regenerated uranium blacks in uranium-molybdenum deposits

International Nuclear Information System (INIS)

Skvortsova, K.V.; Sychev, I.V.; Modnikov, I.S.; Zhil'tsova, I.G.

1980-01-01

Formation conditions of regenerated uranium blacks in the zone of incomplete oxidation and cementation of uranium-molybdenum deposit have been studied. Mixed and regenerated blacks were differed from residual ones by the method of determining excess quantity of lead isotope (Pb 206 ) in ores. Determined were the most favourable conditions for formation of regenerated uranium blacks: sheets of brittle and permeable volcanic rocks characterized by heterogeneous structure of a section, by considerable development of gentle interlayer strippings and zones of hydrothermal alteration; predominance of reduction conditions in a media over oxidation ones under limited oxygen access and other oxidating agents; the composition of hypogenic ores characterized by optimum correlations of uranium minerals, sulfides and carbonates affecting violations of pH in oxidating solutions in the range of 5-6; the initial composition of ground water resulting from climatic conditions of the region and the composition of ore-bearing strata and others. Conditions unfavourable for the formation of regenerated uranium blacks are shown

Uranium from phosphates to rabbit bones: Predicting dietary contribution to uranium deposition in animal bones

International Nuclear Information System (INIS)

Canella Avelar, A.; Motta Ferreira, W.; Menezes, M.

2014-01-01

Uranium is a hazardous element, both for radioactivity and metallotoxicity. Health implications of human overexposure to uranium are well documented: from reproduction impairment, liver and kidney diseases to some types of cancer. There are limited data in the modern literature concerning the levels of uranium in animal tissues and foods, as well the dietary daily intake of uranium is not fully known both for man and livestock. On the other hand, practically every phosphate and its products contain uranium in its structure. The average U content in agricultural phosphate may vary from 10 up to 390 ppm. In this particular feature, uranium can reach animal and man food chain by ingestion of feed and food grade phosphate containing U.

Practical aspects of monitoring and dosimetry of long-lived dust in uranium mines and mills - determination of the annual limit on intake for uranium and uranium/thorium ore dust

International Nuclear Information System (INIS)

Duport, P.; Horvath, F.

1989-01-01

Based on the recommendations of ICRP Publication 26, the dosimetric and metabolic data of ICRP Publication 30, and using available information on the physical and solubility characteristics of uranium and uranium/thorium ore, the ALI values for airborne ore dust were calculated. Four hypothetical types of ore were considered: uranium ore with no radon emanation, uranium ore with 50% radon emanation, uranium/thorium ore with neither 222 Rn nor thoron emanation, and uranium/thorium ore with 50% 22 Rn and 220 Rn emanation. Furthermore, the ALI values were calculated assuming the radionuclides present in the ore were all: (a) solubility class Y: (b) solubility class W; and (c) equal parts of classes Y and W. The ALI values were also calculated for Activity Median Aerodynamic Diameters (AMAD) ranging from 1 to 10 μm. The results of the calculations show that the solubility class of the radionuclides is the single most important factor that governs ALI values. The ALI value for uranium and uranium-thorium ore dust is proportional to (AMAD) 0.5 for class Y materials, (AMAD) 0.2 for a mixture of equal parts of class Y and class W materials, and is independent of the AMAD for class W materials. A series of graphs is given from which it is possible to evaluate the ALI for airborne ore dust when the AMAD of the dust and the solubility characteristics are known approximately. (author)

Continued Multicolumns Bioleaching for Low Grade Uranium Ore at a Certain Uranium Deposit

OpenAIRE

Gongxin Chen; Zhanxue Sun; Yajie Liu

2016-01-01

Bioleaching has lots of advantages compared with traditional heap leaching. In industry, bioleaching of uranium is still facing many problems such as site space, high cost of production, and limited industrial facilities. In this paper, a continued column bioleaching system has been established for leaching a certain uranium ore which contains high fluoride. The analysis of chemical composition of ore shows that the grade of uranium is 0.208%, which is lower than that of other deposits. Howev...

Grade control and the determination of ore reserves at a low-grade uranium mine

International Nuclear Information System (INIS)

Reid, J.A.F.; Robertson, B.

1982-01-01

In 1966 an intensive exploration programme was conducted by Rio Tinto South Africa Ltd, involving airborne and ground radiometric surveys, percussion and diamond drilling, and pilot-plant tests. This investigation established the presence of a large deposit of low-grade uranium that could be mined on a large scale by open-pitting. Soon after production started in June 1974, it was realized that the original presentation of the ore reserves did not give a true reflection of the orebody. A comparison between the estimates and the ore mined from reserve blocks over the period 1975 to 1977 showed that the reserve grades were over-optimistic. In 1977 Rio Tinto Zinc Consultants were commissioned to re-evaluate the ore reserves from exploration diamond-drill data with the help of The Centre de Geostatistique at Fontainebleau, France. A new global reserve using disjunctive kriging techniques was developed, and is now the long-term reserve used for planning purposes at the Roessing Mine. For short-term planning, ore-reserve data are replaced by information from an intermediate drilling programme and blast-hole assays if these are available. A computerized short-term planning system has been established that reconciles the ore mined against the reserve blocks, as well as a system by which composited blast-hole assays are analysed for grade-control purposes. Owing to the complexity of the orebody, additional monitoring is achieved by the scanning of each truckload of ore with a group of scintillation crystal heads that evaluate the material mined

The recycling of reprocessed uranium

International Nuclear Information System (INIS)

Lannegrace, J.-P.

1991-01-01

The 1990 update to the Uranium Institute's report ''Uranium Market Issues'', presented to this Symposium last year (1990) stated that the impact of recycled reprocessing products on uranium demand would be limited in the near future to that due to MOX fuel fabrication. The report stated that the recycling of reprocessed uranium was still at an early discussion stage, rather than being a short-term prospect. This paper will set out to challenge this assertion, on the basis both of facts and of economic and environmental incentives. (author)

Uranium production in thorium/denatured uranium fueled PWRs

International Nuclear Information System (INIS)

Arthur, W.B.

1977-01-01

Uranium-232 buildup in a thorium/denatured uranium fueled pressurized water reactor, PWR(Th), was studied using a modified version of the spectrum-dependent zero dimensional depletion code, LEOPARD. The generic Combustion Engineering System 80 reactor design was selected as the reactor model for the calculations. Reactors fueled with either enriched natural uranium and self-generated recycled uranium or uranium from a thorium breeder and self-generated recycled uranium were considered. For enriched natural uranium, concentrations of 232 U varied from about 135 ppM ( 232 U/U weight basis) in the zeroth generation to about 260 ppM ( 232 U/U weight basis) at the end of the fifth generation. For the case in which thorium breeder fuel (with its relatively high 232 U concentration) was used as reactor makeup fuel, concentrations of 232 U varied from 441 ppM ( 232 U/U weight basis) at discharge from the first generation to about 512 ppM ( 232 U/U weight basis) at the end of the fifth generation. Concentrations in freshly fabricated fuel for this later case were 20 to 35% higher than the discharge concentration. These concentrations are low when compared to those of other thorium fueled reactor types (HTGR and MSBR) because of the relatively high 238 U concentration added to the fuel as a denaturant. Excellent agreement was found between calculated and existing experimental values. Nevertheless, caution is urged in the use of these values because experimental results are very limited, and the relevant nuclear data, especially for 231 Pa and 232 U, are not of high quality

Past and future of uranium production

International Nuclear Information System (INIS)

Max, A.; Mason, T.

1996-01-01

Changes in world politics over the last few years have directly affected supplies and price levels in the front-end nuclear industry. Limited by the advance of CIS and East European uranium and nuclear fuel services into the west, the trend towards a declining uranium industry continued until 1994. The expected introduction of military uranium from Russian and American warheads into the civil nuclear fuel cycle creates additional unknowns in the nuclear fuel market. However, the long lasting recession in the uranium industry may already be coming to an end: The uranium inventories still in existence and uranium from the conversion of nuclear warheads will not last long enough to close the existing gap between uranium demand and supply. Additional uranium production will be required as a result. (orig.) [de

Interaction of uranium with Pleurotus sp

International Nuclear Information System (INIS)

Ohnuki, Toshihiko; Sakamoto, Fuminori; Kozaki, Naofumi; Ozaki, Takuro; Samadfam, Mohammad

2002-01-01

Uptake of uranium by higher fungi, such as mushroom is little elucidated. We have studied the interaction of uranium with Pleurotus sp. (a mushroom) in pure culture over a wide range of U concentration (50-3000 mg/L). The Pleurotus sp. was cultured in two different media. One was rice bran medium, and the other was agar (yeast extract, peptone and dextrose) medium. The uptake of uranium in Pleurotus sp. was examined by alpha ray autoradiography (A,A), X-ray fluorescence spectroscopy (XRF) and scanning microcopy (SEM) equipped with EDS. In the agar medium, the higher uranium concentration gave lower growth of mycelia, and no fruiting body was observed. In the rice bran medium, the fruiting body was grown at U concentrations up to 1000 mg/L. The AA and XRF analysis showed that uranium taken up in the fruiting body was below the detection limit. The SEM-EDS analysis indicated that U was distributed in the limited region and was not transported to the mycelia far from U containing medium. It is concluded that uranium affects the growth of Pleurotus sp., and little uranium is taken up by Pleurotus sp. during the growth of both mycelia and fruiting body. (author)

Dissolution experiments of unirradiated uranium dioxide pellets

International Nuclear Information System (INIS)

Ollila, K.

1985-01-01

The purpose of this study was to measure the dissolution rate of uranium from unirradiated uranium dioxide pellets in deionized water and natural groundwater. Moreover, the solubility limit of uranium in natural groundwater was measured. Two different temperatures, 25 and 60 deg C were used. The low oxygen content of deep groundwater was simulated. The dissolution rate of uranium varied from 10 -7 to 10 -8 g cm -2 d -1 . The rate in reionized water was one order of magnitude lower than in groundwater. No great difference was observed between the natural groundwaters with different composition. Temperature seems to have effect on the dissolution rate. The solubility limit of uranium in natural groundwater in reducing conditions, at 25 deg C, varied from 20 to 600 μg/l and in oxidizing conditions, at 60 deg C, from 4 to 17 mg/l

Training and replacing a 'lost generation' of uranium professionals

International Nuclear Information System (INIS)

Chalmers, M.S.

2007-01-01

It wasn't long ago, actually only a few years ago, when uranium companies and skilled uranium professionals receive little attention and limited interest from other sections of the mining and resource industries. Actually, there were many uranium professionals, whom in some cases, spent over a decade unwinding their CV's to limit the emphasis on uranium exploration and development from the past. Actually, when the bottom fell out of the uranium industry in the late 70's and early 80's there were literally tens of thousands of professionals internationally that were in a major regroup with their careers to get back into mining proper without the uranium connection and believe me, that wasn't always easy. As in most cases, there was no or limited places for uranium professionals wanting to stay in the industry and consequently, virtually all were forced to leave the sector. Who could have predicted that, after nearly 25 years of limited international investment and significant interest in new uranium exploration and development, that the price for yellowcake today would be in excess of US$100/pound? Concerns over energy security and global warming on top of the all-time high uranium price have really come together to make a true uranium renaissance. A renaissance which looks sounder and more sustainable than ever before. So, how is the industry facing a chronic shortage of experience and the huge task of training a multidisciplinary professional workforce going to cope? Effectively there is a 'lost generation' of professionals and very few people available or knowledgeable enough to train those new to the industry. This is a unique problem in the industry and likely more chronic than the other mining sectors, as typically the economic cycles are seven or eight years, not 25 years as has been seen with uranium

Uranium Processing Research in Australia [Processing of Low-Grade Uranium Ores

Energy Technology Data Exchange (ETDEWEB)

Stewart, J R [Australian Atomic Energy Commission, Coogee, N.S.W. (Australia)

1967-06-15

Uranium processing research in Australia has included studies of flotation, magnetic separation, gravity separation, heavy medium separation, atmospheric leaching, multi-stage leaching, alkali leaching, solar heating of leach pulps, jigged-bed resin-in-pulp and solvent-in-pulp extraction. Brief details of the results obtained are given. In general, it can be said that gravity, magnetic and flotation methods are of limited usefulness in the treatment of Australian uranium ores. Alkali leaching seldom gives satisfactory recoveries and multi-stage leaching is expensive. Jigged-bed resin-in-pulp and packed tower solvent-in-pulp extraction systems both show promise, but plant-scale development work is required. Bacterial leaching may be useful in the case of certain low-grade ores. The main difficulties to be overcome, either singly or in combination, in the case of Australian uranium ores not currently considered economically exploitable, are the extremely finely divided state of the uranium mineral, the refractory nature of the uranium mineral and adverse effects due to the gangue minerals present. With respect to known low-grade ores, it would be possible in only a few cases to achieve satisfactory recovery of uranium at reasonable cost by standard treatment methods. (author)

Analysis of uranium intake, risk assessments uranium content in blood and urine

International Nuclear Information System (INIS)

Mukesh Kumar; Prasher, Sangeeta; Singh, Surinder

2015-01-01

Bathinda district of Punjab is in light since the last few years because of the high mortality rate due to cancer. In order to explore the possibility of uranium as one of the causes for cancer an attempt has been made to estimate the level of uranium in the environmental samples viz. soil, water, food items and to correlate it with that in the blood and urine of the cancer patients and the normal persons of the area. The fission track technique has been employed for such studies. Though the uranium content in soil is normal and close to the world average, the uranium values in most of the water samples exceed the recommended safe limits. The cancer risk estimate from drinking of uranium contaminated water during the life time of sixty year is very high. The daily intake of Uranium for the population of these villages including the drinking water has also been estimated using the daily intake of these foodstuffs recommended by WHO and is found to exceed the typical world wide dietary intake of 0.9-4.5 μg/day. The concentration of uranium in urine and blood is found higher in cancer patients, whereas the urine excretion of uranium is lower in the cancer patients compared to the normal persons. (author)

Recovery of uranium from biological adsorbents - desorption equilibrium

International Nuclear Information System (INIS)

Tsezos, M.

1984-01-01

Results are presented of the experimental investigations of uranium elution and reloading for the waste inactive biomass of Rhizopus arrhizus. The experimental data and the analysis of the present work suggest the following conclusions: recovery of uranium that has been taken up by R. arrhizus is possible by elution; of the six elution systems examined, sodium bicarbonate solutions appear to be the most promising because they can effect near complete uranium recovery and high uranium concentration factors; the bicarbonate solution causes the least damage to the biomass; solid-to-liquid ratios in bicarbonate elution systems can exceed 120:1 (mg:mL) for a 1N NaHCO 3 solution, with almost complete uranium recovery and eluate uranium concentrations of over 1.98 x 10 4 mg/L; mineral acids, although good elution agents, result in substantial damage to the biomass thus limiting the biomass reuse potential; sulfate ions in the elutions solution limit the elution potential of the biomass, possibly by conferring novel crystallinity to the cell wall chitin network and confining inside the chitin network more biosorbed uranium

Applied internal dosimetry staff exposed to Uranium

International Nuclear Information System (INIS)

Trotta, Marisa V.; Arguelles, Maria G.

2009-01-01

Dosimetric calculations are performed in order to estimate the quantity of a radionuclide that is incorporated by a worker. Urine determinations of activity and mass of uranium are made in the laboratory of Personal and Area Dosimetry. The paper presents reference values concerning the activity excreted in urine due to the incorporation of uranium compounds. The compounds analyzed are natural uranium and uranium enriched to 20 %, both soluble and insoluble. According to the limits allowed for the incorporation of uranium compounds of Type F and M, we verify that the times of monitoring and the detection limits of the equipment used to determine the activity are appropriate. On the other hand, the S-type compounds determination in urine is useful in cases of accidental incorporations (above the ALI) as a first and quick estimate; MDA (0.017 Bq / L) does not allow detection in routine monitoring; measurement in lungs, and faeces should be included. (author)

Bioassay for uranium mill tailings

International Nuclear Information System (INIS)

Tschaeche, A.N.

1986-01-01

Uranium mill tailings are composed of fine sand that contains, among other things, some uranium (U/sup 238/ primarily), and all of the uranium daughters starting with /sup 230/Th that are left behind after the usable uranium is removed in the milling process. Millions of pounds of tailings are and continue to be generated at uranium mills around the United States. Discrete uranium mill tailings piles exist near the mills. In addition, the tailings materials were used in communities situated near mill sites for such purposes as building materials, foundations for buildings, pipe runs, sand boxes, gardens, etc. The Uranium Mill Tailings Remedial Action Project (UMTRAP) is a U.S. Department of Energy Program designed with the intention of removing or stabilizing the mill tailings piles and the tailings used to communities so that individuals are not exposed above the EPA limits established for such tailings materials. This paper discusses the bioassay programs that are established for workers who remove tailings from the communities in which they are placed

Chemical thermodynamics of uranium

International Nuclear Information System (INIS)

Grenthe, I.; Fuger, J.; Lemire, R.J.; Muller, A.B.; Nguyen-Trung Cregu, C.; Wanner, H.

1992-01-01

A comprehensive overview on the chemical thermodynamics of those elements that are of particular importance in the safety assessment of radioactive waste disposal systems is provided. This is the first volume in a series of critical reviews to be published on this subject. The book provides an extensive compilation of chemical thermodynamic data for uranium. A description of procedures for activity corrections and uncertainty estimates is given. A critical discussion of data needed for nuclear waste management assessments, including areas where significant gaps of knowledge exist is presented. A detailed inventory of chemical thermodynamic data for inorganic compounds and complexes of uranium is listed. Data and their uncertainty limits are recommended for 74 aqueous complexes and 199 solid and 31 gaseous compounds containing uranium, and on 52 aqueous and 17 solid auxiliary species containing no uranium. The data are internally consistent and compatible with the CODATA Key Values. The book contains a detailed discussion of procedures used for activity factor corrections in aqueous solution, as well as including methods for making uncertainty estimates. The recommended data have been prepared for use in environmental geochemistry. Containing contributions written by experts the chapters cover various subject areas such a s: oxide and hydroxide compounds and complexes, the uranium nitrides, the solid uranium nitrates and the arsenic-containing uranium compounds, uranates, procedures for consistent estimation of entropies, gaseous and solid uranium halides, gaseous uranium oxides, solid phosphorous-containing uranium compounds, alkali metal uranates, uncertainties, standards and conventions, aqueous complexes, uranium minerals dealing with solubility products and ionic strength corrections. The book is intended for nuclear research establishments and consulting firms dealing with uranium mining and nuclear waste disposal, as well as academic and research institutes

Uranium isotopic composition and uranium concentration in special reference material SRM A (uranium in KCl/LiCl salt matrix)

International Nuclear Information System (INIS)

Graczyk, D.G.; Essling, A.M.; Sabau, C.S.; Smith, F.P.; Bowers, D.L.; Ackerman, J.P.

1997-07-01

To help assure that analysis data of known quality will be produced in support of demonstration programs at the Fuel Conditioning Facility at Argonne National Laboratory-West (Idaho Falls, ID), a special reference material has been prepared and characterized. Designated SRM A, the material consists of individual units of LiCl/KCl eutectic salt containing a nominal concentration of 2.5 wt. % enriched uranium. Analyses were performed at Argonne National Laboratory-East (Argonne, IL) to determine the uniformity of the material and to establish reference values for the uranium concentration and uranium isotopic composition. Ten units from a batch of approximately 190 units were analyzed by the mass spectrometric isotope dilution technique to determine their uranium concentration. These measurements provided a mean value of 2.5058 ± 0.0052 wt. % U, where the uncertainty includes estimated limits to both random and systematic errors that might have affected the measurements. Evidence was found of a small, apparently random, non-uniformity in uranium content of the individual SRM A units, which exhibits a standard deviation of 0.078% of the mean uranium concentration. Isotopic analysis of the uranium from three units, by means of thermal ionization mass spectrometry with a special, internal-standard procedure, indicated that the uranium isotopy is uniform among the pellets with a composition corresponding to 0.1115 ± 0.0006 wt. % 234 U, 19.8336 ± 0.0059 wt. % 235 U, 0.1337 ± 0.0006 wt. % 236 U, and 79.9171 ± 0.0057 wt. % 238 U

Analysis of uranium in urine of persons occupationaly exposed

International Nuclear Information System (INIS)

Nunes, S.C.

1985-01-01

A technique of uranium analysis in urine of persons occupationaly exposed, using the fluorimetric method is proposed. Two procedures for the determination are presented: the first employs platinum dishes, obtaining a detection limit of 1 ppb and the second one, using aluminium dishes, shows a detection limit of 100 ppb. Uranium and urine physico-chemical characteristics are described, as well as norms for the exposition of workers to uranium. (M.A.C.) [pt

Fluorimetric determination of uranium in water

International Nuclear Information System (INIS)

Acosta L, E.

1992-02-01

The fluorimetric method for the determination of microquantities of uranium in water is described. This method covers the determination of uranium in water in the interval from 0.2 to 50 ppm on 50 ml. of radioactive base sample. These limits can be variable if the volume of the aliquot one of the base sample is changed, as well as the volume of the used aliquot one for to the final determination of uranium. (Author)

Continued Multicolumns Bioleaching for Low Grade Uranium Ore at a Certain Uranium Deposit

Directory of Open Access Journals (Sweden)

Gongxin Chen

2016-01-01

Full Text Available Bioleaching has lots of advantages compared with traditional heap leaching. In industry, bioleaching of uranium is still facing many problems such as site space, high cost of production, and limited industrial facilities. In this paper, a continued column bioleaching system has been established for leaching a certain uranium ore which contains high fluoride. The analysis of chemical composition of ore shows that the grade of uranium is 0.208%, which is lower than that of other deposits. However, the fluoride content (1.8% of weight is greater than that of other deposits. This can be toxic for bacteria growth in bioleaching progress. In our continued multicolumns bioleaching experiment, the uranium recovery (89.5% of 4th column is greater than those of other columns in 120 days, as well as the acid consumption (33.6 g/kg. These results indicate that continued multicolumns bioleaching technology is suitable for leaching this type of ore. The uranium concentration of PLS can be effectively improved, where uranium recovery can be enhanced by the iron exchange system. Furthermore, this continued multicolumns bioleaching system can effectively utilize the remaining acid of PLS, which can reduce the sulfuric acid consumption. The cost of production of uranium can be reduced and this benefits the environment too.

World uranium resources

International Nuclear Information System (INIS)

Deffeyes, K.S.; MacGregor, I.D.

1980-01-01

To estimate the total resource availability of uranium, the authors' approach has been to ask whether the distribution of uranium in the earth's crust can be reasonably approximated by a bell-shaped log-normal curve. In addition they have asked whether the uranium deposits actually mined appear to be a portion of the high-grade tail, or ascending slope, of the distribution. This approach preserves what they feel are the two most important guiding principles of Hubbert's work, for petroleum, namely recognizing the geological framework that contains the deposits of interest and examining the industry's historical record of discovering those deposits. Their findings, published recently in the form of a book-length report prepared for the US Department of Energy, suggest that for uranium the crustal-distribution model and the mining-history model can be brought together in a consistent picture. In brief, they conclude that both sets of data can be described by a single log-normal curve, the smoothly ascending slope of which indicates approximately a 300-fold increase in the amount of uranium recoverable for each tenfold decrease in ore grade. This conclusion has important implications for the future availability of uranium. They hasten to add, however, that this is only an approximative argument; no rigorous statistical basis exists for expecting a log-normal distribution. They continue, pointing out the enormously complex range of geochemical behavior of uranium - and its wide variety of different binds of economic deposit. Their case study, supported by US mining records, indicates that the supply of uranium will not be a limiting factor in the development of nuclear power

Uranium in alkaline rocks

Energy Technology Data Exchange (ETDEWEB)

Murphy, M.; Wollenberg, H.; Strisower, B.; Bowman, H.; Flexser, S.; Carmichael, I.

1978-04-01

Geologic and geochemical criteria were developed for the occurrence of economic uranium deposits in alkaline igneous rocks. A literature search, a limited chemical analytical program, and visits to three prominent alkaline-rock localities (Ilimaussaq, Greenland; Pocos de Caldas, Brazil; and Powderhorn, Colorado) were made to establish criteria to determine if a site had some uranium resource potential. From the literature, four alkaline-intrusive occurrences of differing character were identified as type-localities for uranium mineralization, and the important aspects of these localities were described. These characteristics were used to categorize and evaluate U.S. occurrences. The literature search disclosed 69 U.S. sites, encompassing nepheline syenite, alkaline granite, and carbonatite. It was possible to compare two-thirds of these sites to the type localities. A ranking system identified ten of the sites as most likely to have uranium resource potential.

Uranium in alkaline rocks

International Nuclear Information System (INIS)

Murphy, M.; Wollenberg, H.; Strisower, B.; Bowman, H.; Flexser, S.; Carmichael, I.

1978-04-01

Geologic and geochemical criteria were developed for the occurrence of economic uranium deposits in alkaline igneous rocks. A literature search, a limited chemical analytical program, and visits to three prominent alkaline-rock localities (Ilimaussaq, Greenland; Pocos de Caldas, Brazil; and Powderhorn, Colorado) were made to establish criteria to determine if a site had some uranium resource potential. From the literature, four alkaline-intrusive occurrences of differing character were identified as type-localities for uranium mineralization, and the important aspects of these localities were described. These characteristics were used to categorize and evaluate U.S. occurrences. The literature search disclosed 69 U.S. sites, encompassing nepheline syenite, alkaline granite, and carbonatite. It was possible to compare two-thirds of these sites to the type localities. A ranking system identified ten of the sites as most likely to have uranium resource potential

Oxidation of uranium and uranium alloys

International Nuclear Information System (INIS)

Orman, S.

1976-01-01

The corrosion behaviour of uranium in oxygen, water and water + oxygen mixtures is compared and contrasted. A considerable amount of work, much of it conflicting, has been published on the U + H 2 O and U + H 2 O + O 2 systems. An attempt has been made to summarise this data and to explain the reasons for the lack of agreement between the experimental results. The evidence for the mechanism involving OH - ion diffusion as the reacting entity in both the U + H 2 O and U + O 2 + H 2 O reactions is advanced. The more limited corrosion data on some lean uranium alloys and on some higher addition alloys referred to as stainless materials is summarised together with some previously unreported results obtained with these materials at AWRE. The data indicates that in the absence of oxygen the lean alloys behave in a similar manner to uranium and evolve hydrogen in approximately theoretical quantities. But the stainless alloys absorb most of the product hydrogen and assessments of reactivity based on hydrogen evolution would be very inaccurate. The direction that future corrosion work on these materials should take is recommended

Cost Analysis of Remediation Systems for Depleted Uranium

Science.gov (United States)

2014-04-01

radioactive metal in all rocks and soils. There are three existing uranium isotopes, and all three are radioactive and emit decay products upon...the chemical toxicity of soluble forms of uranium . If internalized, uranium will cause health problems, as is the case with other heavy metals such...blunt mushroom shape as it penetrates armor, which limits its effectiveness. With a density of 17.6 g/cm3 it weighs less than DU. Uranium oxidizes

National uranium resource evaluation Prescott Quadrangle Arizona

International Nuclear Information System (INIS)

May, R.T.; White, D.L.; Nystrom, R.J.

1982-01-01

The Prescott Quadrangle was evaluated for uranium favorability by means of a literature search, examination of uranium occurrences, regional geochemical sampling of Precambrian rocks, limited rubidium-strontium studies, scintillometer traverses, measurement of stratigraphic sections, subsurface studies, and an aerial radiometric survey. A limited well-water sampling program for Cenozoic basins was also conducted. Favorability criteria used were those developed for the National Uranium Resource Evaluation. Five geologic environments are favorable for uranium. Three are in Tertiary rocks of the Date Creek-Artillery Basin, Big Sandy Valley, and Walnut Grove Basin. Two are in Precambrian rocks in the Bagdad and Wickenburg areas. Unfavorable areas include the southwestern crystalline terrane, the Paleozoic and Mesozoic beds, and metamorphic and plutonic Precambrian rocks of the Bradshaw and Weaver Mountains. Unevaluated areas are the basalt-covered mesas, alluvium-mantled Cenozoic basins, the Hualapai Mountains, and the Kellwebb Mine

Uranium Elemental and Isotopic Constraints on Groundwater Flow Beneath the Nopal I Uranium Deposit, Pena Blanca, Mexico

International Nuclear Information System (INIS)

S.J. Goldstein; M.T. Murrell; A.M. Simmons

2005-01-01

The Nopal I uranium deposit in Chihuahua, Mexico, is an excellent analogue for evaluating the fate of spent fuel, associated actinides, and fission products over long time scales for the proposed Yucca Mountain high-level nuclear waste repository. In 2003, three groundwater wells were drilled directly adjacent to (PB-1) and 50 m on either side of the uranium deposit (PB-2 and PB-3) in order to evaluate uranium-series transport in three dimensions. After drilling, uranium concentrations were elevated in all of the three wells (0.1-18 ppm) due to drilling activities and subsequently decreased to ∼5-20% of initial values over the next several months. The 234 U/ 238 U activity ratios were similar for PB-1 and PB-2 (1.005 to 1.079) but distinct for PB-3 (1.36 to 1.83) over this time period, suggesting limited mixing between groundwater from these wells over these short time and length scales. Regional groundwater wells located up to several km from the deposit also have distinct uranium isotopic characteristics and constrain mixing over larger length and time scales. We model the decreasing uranium concentrations in the newly drilled wells with a simple one-dimensional advection-dispersion model, assuming uranium is introduced as a slug to each of the wells and transported as a conservative tracer. Using this model for our data, the relative uranium concentrations are dependent on both the longitudinal dispersion as well as the mean groundwater flow velocity. These parameters have been found to be correlated in both laboratory and field studies of groundwater velocity and dispersion (Klotz et al., 1980). Using typical relationships between velocity and dispersion for field and laboratory studies along with the relationship observed from our uranium data, both velocity (1-10 n/yr) and dispersion coefficient (1E-5 to 1E-2 cm 2 /s) can be derived from the modeling. As discussed above, these relatively small flow velocities and dispersivities agree with mixing

Yellow cake to ceramic uranium dioxide

International Nuclear Information System (INIS)

Zawidzki, T.W.; Itzkovitch, I.J.

1983-01-01

This overview article first reviews the processes for converting uranium ore concentrates to ceramic uranium dioxide at the Port Hope Refinery of Eldorado Resources Limited. In addition, some of the problems, solutions, thoughts and research direction with respect to the production and properties of ceramic UO 2 are described

Mortality (1968-2008) in a French cohort of uranium enrichment workers potentially exposed to rapidly soluble uranium compounds.

Science.gov (United States)

Zhivin, Sergey; Guseva Canu, Irina; Samson, Eric; Laurent, Olivier; Grellier, James; Collomb, Philippe; Zablotska, Lydia B; Laurier, Dominique

2016-03-01

Until recently, enrichment of uranium for civil and military purposes in France was carried out by gaseous diffusion using rapidly soluble uranium compounds. We analysed the relationship between exposure to soluble uranium compounds and exposure to external γ-radiation and mortality in a cohort of 4688 French uranium enrichment workers who were employed between 1964 and 2006. Data on individual annual exposure to radiological and non-radiological hazards were collected for workers of the AREVA NC, CEA and Eurodif uranium enrichment plants from job-exposure matrixes and external dosimetry records, differentiating between natural, enriched and depleted uranium. Cause-specific mortality was compared with the French general population via standardised mortality ratios (SMR), and was analysed via Poisson regression using log-linear and linear excess relative risk models. Over the period of follow-up, 131 161 person-years at risk were accrued and 21% of the subjects had died. A strong healthy worker effect was observed: all causes SMR=0.69, 95% CI 0.65 to 0.74. SMR for pleural cancer was significantly increased (2.3, 95% CI 1.06 to 4.4), but was only based on nine cases. Internal uranium and external γ-radiation exposures were not significantly associated with any cause of mortality. This is the first study of French uranium enrichment workers. Although limited in statistical power, further follow-up of this cohort, estimation of internal uranium doses and pooling with similar cohorts should elucidate potential risks associated with exposure to soluble uranium compounds. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

The US uranium industry: Regulatory and policy impediments

Energy Technology Data Exchange (ETDEWEB)

Drennen, T.E.; Glicken, J.

1995-06-01

The Energy Policy Act of 1992 required the DOE to develop recommendations and implement government programs to assist the domestic uranium industry in increasing export opportunities. In 1993, as part of that effort, the Office of Nuclear Energy identified several key factors that could (or have) significantly impact(ed) export opportunities for domestic uranium. This report addresses one of these factors: regulatory and policy impediments to the flow of uranium products between the US and other countries. It speaks primarily to the uranium market for civil nuclear power. Changes in the world political and economic order have changed US national security requirements, and the US uranium industry has found itself without the protected market it once enjoyed. An unlevel playing field for US uranium producers has resulted from a combination of geology, history, and a general US political philosophy of nonintervention that precludes the type of industrial policy practiced in other uranium-exporting countries. The US has also been hampered in its efforts to support the domestic uranium-producing industry by its own commitment to free and open global markets and by international agreements such as GATT and NAFTA. Several US policies, including the imposition of NRC fees and licensing costs and Harbor Maintenance fees, directly harm the competitiveness of the domestic uranium industry. Finally, requirements under US law, such as those in the 1979 Nuclear Nonproliferation Act, place very strict limits on the use of US-origin uranium, limitations not imposed by other uranium-producing countries. Export promotion and coordination are two areas in which the US can help the domestic uranium industry without violating existing trade agreements or other legal or policy constraints.

The US uranium industry: Regulatory and policy impediments

International Nuclear Information System (INIS)

Drennen, T.E.; Glicken, J.

1995-06-01

The Energy Policy Act of 1992 required the DOE to develop recommendations and implement government programs to assist the domestic uranium industry in increasing export opportunities. In 1993, as part of that effort, the Office of Nuclear Energy identified several key factors that could (or have) significantly impact(ed) export opportunities for domestic uranium. This report addresses one of these factors: regulatory and policy impediments to the flow of uranium products between the US and other countries. It speaks primarily to the uranium market for civil nuclear power. Changes in the world political and economic order have changed US national security requirements, and the US uranium industry has found itself without the protected market it once enjoyed. An unlevel playing field for US uranium producers has resulted from a combination of geology, history, and a general US political philosophy of nonintervention that precludes the type of industrial policy practiced in other uranium-exporting countries. The US has also been hampered in its efforts to support the domestic uranium-producing industry by its own commitment to free and open global markets and by international agreements such as GATT and NAFTA. Several US policies, including the imposition of NRC fees and licensing costs and Harbor Maintenance fees, directly harm the competitiveness of the domestic uranium industry. Finally, requirements under US law, such as those in the 1979 Nuclear Nonproliferation Act, place very strict limits on the use of US-origin uranium, limitations not imposed by other uranium-producing countries. Export promotion and coordination are two areas in which the US can help the domestic uranium industry without violating existing trade agreements or other legal or policy constraints

Uranium determination in water

International Nuclear Information System (INIS)

Prudenzo, E.J.; Puga, Maria J.; Cerchietti, Maria L.R.; Arguelles, Maria G.

2005-01-01

In our laboratory, a procedure has been assessed to determine uranium content of water in normal situations. The method proposed without sample pre-treatment, is simple and rapid. Uranium mass is measured by fluorimetry. For calculation of detection limit (Ld) and quantification level (Lq) we used blank samples and the results were analyzed for different statistical test. The calculation of total propagated uncertainty and sources contribution on real samples are presented. (author)

The utilization of uranium industry technology and relevant chemistry to leach uranium from mixed-waste solids

International Nuclear Information System (INIS)

Mattus, A.J.; Farr, L.L.

1991-01-01

Methods for the chemical extraction of uranium from a number of refractory uranium-containing minerals found in nature have been in place and employed by the uranium mining and milling industry for nearly half a century. These same methods, in conjunction with the principles of relevant uranium chemistry, have been employed at the Oak Ridge National Laboratory (ORNL) to chemically leach depleted uranium from mixed-waste sludge and soil. The removal of uranium from what is now classified as mixed waste may result in the reclassification of the waste as hazardous, which may then be delisted. The delisted waste might eventually be disposed of in commercial landfill sites. This paper generally discusses the application of chemical extractive methods to remove depleted uranium from a biodenitrification sludge and a storm sewer soil sediment from the Y-12 weapons plant in Oak Ridge. Some select data obtained from scoping leach tests on these materials are presented along with associated limitations and observations which might be useful to others performing such test work. 6 refs., 2 tabs

The utilization of uranium industry technology and relevant chemistry to leach uranium from mixed-waste solids

Energy Technology Data Exchange (ETDEWEB)

Mattus, A.J.; Farr, L.L.

1991-01-01

Methods for the chemical extraction of uranium from a number of refractory uranium-containing minerals found in nature have been in place and employed by the uranium mining and milling industry for nearly half a century. These same methods, in conjunction with the principles of relevant uranium chemistry, have been employed at the Oak Ridge National Laboratory (ORNL) to chemically leach depleted uranium from mixed-waste sludge and soil. The removal of uranium from what is now classified as mixed waste may result in the reclassification of the waste as hazardous, which may then be delisted. The delisted waste might eventually be disposed of in commercial landfill sites. This paper generally discusses the application of chemical extractive methods to remove depleted uranium from a biodenitrification sludge and a storm sewer soil sediment from the Y-12 weapons plant in Oak Ridge. Some select data obtained from scoping leach tests on these materials are presented along with associated limitations and observations which might be useful to others performing such test work. 6 refs., 2 tabs.

Standard specification for sintered gadolinium oxide-uranium dioxide pellets

CERN Document Server

American Society for Testing and Materials. Philadelphia

2008-01-01

1.1 This specification is for finished sintered gadolinium oxide-uranium dioxide pellets for use in light-water reactors. It applies to gadolinium oxide-uranium dioxide pellets containing uranium of any 235U concentration and any concentration of gadolinium oxide. 1.2 This specification recognizes the presence of reprocessed uranium in the fuel cycle and consequently defines isotopic limits for gadolinium oxide-uranium dioxide pellets made from commercial grade UO2. Such commercial grade UO2 is defined so that, regarding fuel design and manufacture, the product is essentially equivalent to that made from unirradiated uranium. UO2 falling outside these limits cannot necessarily be regarded as equivalent and may thus need special provisions at the fuel fabrication plant or in the fuel design. 1.3 This specification does not include (1) provisions for preventing criticality accidents or (2) requirements for health and safety. Observance of this specification does not relieve the user of the obligation to be aw...

Final environmental statement related to the Plateau Resources Limited Shootering Canyon Uranium Project (Garfield County, Utah)

International Nuclear Information System (INIS)

1979-07-01

The proposed action is the issuance of a Source Material License to Plateau Resources, Ltd., for the construction and operation of the proposed Shootering Canyon Uranium Project with a product (U 3 O 8 ) production limited to 2.2 x 10 5 kg (4.9 x 10 5 lb) per year. Impacts to the area from the operation of the Shootering Canyon Uranium Project will include the following: alterations of up to 140 ha (350 acres) that will be occupied by the mill, mill facilities, borrow areas, tailings areas, and roads; an increase in the existing background radiation levels of the mill area as a result of continuous but small releases of uranium, radium, radon, and other, radioactive materials during construction and operation; socioeconomic effects on the local area, particularly the proposed community of Ticaboo, where the majority of workers will be housed during project construction and operation; and production of solid waste material (tailings) from the mill at a rate of about 680 MT (750 tons) per day and deposition as a slurry in an onsite impoundment area; construction and operation of the Shootering Canyon mill will provide employment and induced economic benefits for the region but may also result in some socioeconomic stress. On the basis of the analysis and evaluation set forth in this Environmental Statement, it is proposed that any license issued for the Shootering Canyon mill should be subject to certain conditions for the protection of the environment. A list is included. Nine appendices are also included

Principles of modern uranium exploration

International Nuclear Information System (INIS)

King, J.W.

1974-01-01

The Athens Symposium followed the recommendations of a panel meeting in April 1970 on uranium exploration geology. It was attended by 220 participants representing 40 countries and two international organizations; 43 papers were presented. An overview of the supply challenge of uranium was given by Mr. Robert D. Nininger, of the USAEC, who acted as chairman of the Symposium. He outlined the major topics and problems to be discussed during the conference, with the aim of meeting this challenge: 'Uranium deposits in sandstone and quartz pebble conglomerates presently represent the preponderance of uranium resources. Yet there is a question whether geologic limitations on the occurrence of such deposits may preclude their discovery in numbers sufficient to meet the eventual resource needs. New types of deposits, low in grade but larger in size, representing the equivalent of the porphyry copper deposits, may supply the bulk of future resource additions. Further investigation is needed on the characteristics of such deposits and the means of their identification. Similarly, additional investigation is needed to determine whether limits on the more conventional deposits do, in fact, exist, and, if not, what advanced approaches to rapid identification of additional such deposits may be employed'

Uranium exports could match oil imports. [status and prospects of the Canadian uranium industry

Energy Technology Data Exchange (ETDEWEB)

McIntyre, H C

1977-04-01

Apart from a temporary embargo while safeguards are negotiated, the Canadian government limits uranium exports so as to guarantee fuel for every Canadian reactor built or planned for 30 years. On the basis of present known reserves of 172 Gg of 'cheap' U/sub 3/O/sub 8/ and 33 of 'dear', that would mean phasing out exports after the mid 1980's, but probably much more 'dear' uranium remains to be discovered. Provincial taxation and restrictions on foreign ownership may be limitations. Discoveries range over eleven areas, but production capacity at present is 14190 Mg/d from Ontario and 3400 from Saskatchewan, with 8800 mothballed and 4860 planned or being rehabilitated. The price has jumped to $95/kg, so that uranium exports may cover half the cost of oil imports. All producers use sulfuric acid leaching, except Eldorado, which uses carbonate leaching; a process using tertiary amine is being developed. Development of the organic-cooled Th//sup 233/U fuelled reactor may greatly extend fuel resources.

Potentiometric determination of hexavalent uranium in uranium silicide samples

International Nuclear Information System (INIS)

Arlegui, Oscar

1999-01-01

The Chilean Nuclear Energy Commission's Department of Nuclear Materials has among its projects the production of fuels elements for nuclear reactors, and, therefore, the Chemical Analysis Laboratory must have a rapid and reliable method for uranium analysis, to control the uranium concentration during each stage of the production process. For this reason the Chilean Nuclear Energy Commission's Chemical Analysis Laboratory has validated a potentiometric method, which is a modification of the Davies and Gray method proposed by A.R. Eberle. This method uses the Potentiometric Titration Technique and is based on the direct and rapid reduction of uranium (VI) to Uranium (IV), in a concentrated phosphoric acid medium, with excess iron (II) used as a reducing agent. In this medium the excess iron (II) selectively oxidizes to iron (III) with nitric acid, using molybdenum (IV) as a catalyzer, the nitrous acid that is produced is eliminated by adding amidosulfuric acid. The solution is diluted with 1M sulfuric acid and the uranium (IV) obtained is titrated potentiometrically with potassium dichromate in the presence of vanadilic sulfate to obtain a better defined final titration point. The samples were softened with hydrochloric acid and nitric acid and later 50 ml were estimated in a 20% sulfuric acid medium. The analytical method was validated by comparing it with Certified Reference Material (C.R.M.) from the New Brunswick Laboratory (NBL), Metallic Uranium, CRM 112-A. The F Test and the T Test show that the value calculated is less than the tabulated value so the result is traceable to the reference material. The quantification limit, sensitivity, precision and accuracy were quantified for the method

Experimental Plan: Uranium Stabilization Through Polyphosphate Injection 300 Area Uranium Plume Treatability Demonstration Project

Energy Technology Data Exchange (ETDEWEB)

Wellman, Dawn M.; Fruchter, Jonathan S.; Vermeul, Vince R.

2006-09-20

This Test Plan describes a laboratory-testing program to be performed at Pacific Northwest National Laboratory (PNNL) in support of the 300-FF-5 Feasibility Study (FS). The objective of the proposed treatability test is to evaluate the efficacy of using polyphosphate injections to treat uranium contaminated groundwater in situ. This study will be used to: (1) Develop implementation cost estimates; (2) Identify implementation challenges; and (3) Investigate the technology's ability to meet remedial objectives These activities will be conducted in parallel with a limited field investigation, which is currently underway to more accurately define the vertical extent of uranium in the vadose zone, and in the capillary fringe zone laterally throughout the plume. The treatability test will establish the viability of the method and, along with characterization data from the limited field investigation, will provide the means for determining how best to implement the technology in the field. By conducting the treatability work in parallel with the ongoing Limited Field Investigation, the resulting Feasibility Study (FS) will provide proven, site-specific information for evaluating polyphosphate addition and selecting a suitable remediation strategy for the uranium plume within the FS time frame at an overall cost savings.

Effects of technological learning and uranium price on nuclear cost: Preliminary insights from a multiple factors learning curve and uranium market modeling

International Nuclear Information System (INIS)

Kahouli, Sondes

2011-01-01

This paper studies the effects of returns to scale, technological learning, i.e. learning-by-doing and learning-by-searching, and uranium price on the prospects of nuclear cost decrease. We use an extended learning curve specification, named multiple factors learning curve (MFLC). In a first stage, we estimate a single MFLC. In a second stage, we estimate the MFLC under the framework of simultaneous system of equations which takes into account the uranium supply and demand. This permits not only to enhance the reliability of the estimation by incorporating the uranium price formation mechanisms in the MFLC via the price variable, but also to give preliminary insights about uranium supply and demand behaviors and the associated effects on the nuclear expansion. Results point out that the nuclear cost has important prospects for decrease via capacity expansion, i.e. learning-by-doing effects. In contrast, they show that the learning-by-searching as well as the scale effects have a limited effect on the cost decrease prospects. Conversely, results also show that uranium price exerts a positive and significant effect on nuclear cost, implying that when the uranium price increases, the nuclear power generation cost decreases. Since uranium is characterized by important physical availability, and since it represents only a minor part in the total nuclear cost, we consider that in a context of increasing demand for nuclear energy the latter result can be explained by the fact that the positive learning effects on the cost of nuclear act in a way to dissipate the negative ones that an increase in uranium price may exert. Further, results give evidence of important inertia in the supply and demand sides as well as evidence of slow correlation between the uranium market and oil market which may limit the inter-fuels substituability effects, that is, nuclear capacity expansion and associated learning-by-doing benefits. - Highlights: → We study the prospects of nuclear cost

The use of uranium isotopes and the U/Th ratio to evaluate the fingerprint of plants following uranium releases from fuel cycle settlements

International Nuclear Information System (INIS)

Pourcelot, L.; Boulet, B.; Cariou, N.

2015-01-01

This paper uses data from the environmental monitoring of fuel cycle settlements. It aims to evaluate uranium released into the terrestrial environment. Measurement of uranium isotopes in terrestrial plants allows illustrating the consequences of chronic and incidental releases of depleted uranium into the atmosphere. However, such an analytical approach reaches its limits when natural uranium is released. Indeed, distinguishing natural uranium from releases and uranium from the radiological background is difficult. For this reason, we propose normalizing uranium activity measured in plants taken in the surroundings of nuclear sites with respect to 232 Th, considering that the source of this latter is the background. (authors)

Uranium

International Nuclear Information System (INIS)

Hamdoun, N.A.

2007-01-01

The article includes a historical preface about uranium, discovery of portability of sequential fission of uranium, uranium existence, basic raw materials, secondary raw materials, uranium's physical and chemical properties, uranium extraction, nuclear fuel cycle, logistics and estimation of the amount of uranium reserves, producing countries of concentrated uranium oxides and percentage of the world's total production, civilian and military uses of uranium. The use of depleted uranium in the Gulf War, the Balkans and Iraq has caused political and environmental effects which are complex, raising problems and questions about the effects that nuclear compounds left on human health and environment.

Uranium extraction from gold-uranium ores

Energy Technology Data Exchange (ETDEWEB)

Laskorin, B.N.; Golynko, Z.Sh.

1981-01-01

The process of uranium extraction from gold-uranium ores in the South Africa is considered. Flowsheets of reprocessing gold-uranium conglomerates, pile processing and uranium extraction from the ores are presented. Continuous counter flow ion-exchange process of uranium extraction using strong-active or weak-active resins is noted to be the most perspective and economical one. The ion-exchange uranium separation with the succeeding extraction is also the perspective one.

Method for converting uranium oxides to uranium metal

International Nuclear Information System (INIS)

Duerksen, W.K.

1988-01-01

A method for converting uranium oxide to uranium metal is described comprising the steps of heating uranium oxide in the presence of a reducing agent to a temperature sufficient to reduce the uranium oxide to uranium metal and form a heterogeneous mixture of a uranium metal product and oxide by-products, heating the mixture in a hydrogen atmosphere at a temperature sufficient to convert uranium metal in the mixture to uranium hydride, cooling the resulting uranium hydride-containing mixture to a temperature sufficient to produce a ferromagnetic transition in the uranium hydride, magnetically separating the cooled uranium hydride from the mixture, and thereafter heating the separated uranium hydride in an inert atmosphere to a temperature sufficient to convert the uranium hydride to uranium metal

Thermodynamic properties of α-uranium

International Nuclear Information System (INIS)

Ren, Zhiyong; Wu, Jun; Ma, Rong; Hu, Guichao; Luo, Chao

2016-01-01

The lattice constants and equilibrium atomic volume of α-uranium were calculated by Density Functional Theory (DFT). The first principles calculation results of the lattice for α-uranium are in agreement with the experimental results well. The thermodynamic properties of α-uranium from 0 to 900 K and 0–100 GPa were calculated with the quasi-harmonic Debye model. Volume, bulk modulus, entropy, Debye temperature, thermal expansion coefficient and the heat capacity of α-uranium were calculated. The calculated results show that the bulk modulus and Debye temperature increase with the increasing pressure at a given temperature while decreasing with the increasing temperature at a given pressure. Volume, entropy, thermal expansion coefficient and the heat capacity decrease with the increasing pressure while increasing with the increasing temperature. The theoretical results of entropy, Debye temperature, thermal expansion coefficient and the heat capacity show good agreement with the general trends of the experimental values. The constant-volume heat capacity shows typical Debye T"3 power-law behavior at low temperature limit and approaches to the classical asymptotic Dulong-Petit limit at high temperature limit. - Highlights: • Thermodynamic properties of α-U were predicted systematically with quasi-harmonic Debye model. • Summarizations of the corresponding experimental and theoretical results have been made for the EOS and other thermodynamic parameters. • The calculated thermodynamic properties show good agreement with the experimental results in general trends.

Thermodynamic properties of α-uranium

Energy Technology Data Exchange (ETDEWEB)

Ren, Zhiyong; Wu, Jun; Ma, Rong; Hu, Guichao; Luo, Chao, E-mail: luochaoboss@sohu.com

2016-11-15

The lattice constants and equilibrium atomic volume of α-uranium were calculated by Density Functional Theory (DFT). The first principles calculation results of the lattice for α-uranium are in agreement with the experimental results well. The thermodynamic properties of α-uranium from 0 to 900 K and 0–100 GPa were calculated with the quasi-harmonic Debye model. Volume, bulk modulus, entropy, Debye temperature, thermal expansion coefficient and the heat capacity of α-uranium were calculated. The calculated results show that the bulk modulus and Debye temperature increase with the increasing pressure at a given temperature while decreasing with the increasing temperature at a given pressure. Volume, entropy, thermal expansion coefficient and the heat capacity decrease with the increasing pressure while increasing with the increasing temperature. The theoretical results of entropy, Debye temperature, thermal expansion coefficient and the heat capacity show good agreement with the general trends of the experimental values. The constant-volume heat capacity shows typical Debye T{sup 3} power-law behavior at low temperature limit and approaches to the classical asymptotic Dulong-Petit limit at high temperature limit. - Highlights: • Thermodynamic properties of α-U were predicted systematically with quasi-harmonic Debye model. • Summarizations of the corresponding experimental and theoretical results have been made for the EOS and other thermodynamic parameters. • The calculated thermodynamic properties show good agreement with the experimental results in general trends.

Trends in uranium supply

Energy Technology Data Exchange (ETDEWEB)

Hansen, M [International Atomic Energy Agency, Division of Nuclear Power and Reactors, Nuclear Materials and Fuel Cycle Section, Vienna (Austria)

1976-07-01

Prior to the development of nuclear power, uranium ores were used to a very limited extent as a ceramic colouring agent, as a source of radium and in some places as a source of vanadium. Perhaps before that, because of the bright orange and yellow colours of its secondary ores, it was probably used as ceremonial paint by primitive man. After the discovery of nuclear fission a whole new industry emerged, complete with its problems of demand, resources and supply. Spurred by special incentives in the early years of this new nuclear industry, prospectors discovered over 20 000 occurrences of uranium in North America alone, and by 1959 total world production reached a peak of 34 000 tonnes uranium from mines in South Africa, Canada and United States. This rapid growth also led to new problems. As purchases for military purposes ended, government procurement contracts were not renewed, and the large reserves developed as a result of government purchase incentives, in combination with lack of substantial commercial market, resulted in an over-supply of uranium. Typically, an over-supply of uranium together with national stockpiling at low prices resulted in depression of prices to less than $5 per pound by 1971. Although forecasts made in the early 1970's increased confidence in the future of nuclear power, and consequently the demand for uranium, prices remained low until the end of 1973 when OPEC announced a very large increase in oil prices and quite naturally, prices for coal also rose substantially. The economics of nuclear fuel immediately improved and prices for uranium began to climb in 1974. But the world-wide impact of the OPEC decision also produced negative effects on the uranium industry. Uranium production costs rose dramatically, as did capital costs, and money for investment in new uranium ventures became more scarce and more expensive. However, the uranium supply picture today offers hope of satisfactory development in spite of the many problems to be

Trends in uranium supply

International Nuclear Information System (INIS)

Hansen, M.

1976-01-01

Prior to the development of nuclear power, uranium ores were used to a very limited extent as a ceramic colouring agent, as a source of radium and in some places as a source of vanadium. Perhaps before that, because of the bright orange and yellow colours of its secondary ores, it was probably used as ceremonial paint by primitive man. After the discovery of nuclear fission a whole new industry emerged, complete with its problems of demand, resources and supply. Spurred by special incentives in the early years of this new nuclear industry, prospectors discovered over 20 000 occurrences of uranium in North America alone, and by 1959 total world production reached a peak of 34 000 tonnes uranium from mines in South Africa, Canada and United States. This rapid growth also led to new problems. As purchases for military purposes ended, government procurement contracts were not renewed, and the large reserves developed as a result of government purchase incentives, in combination with lack of substantial commercial market, resulted in an over-supply of uranium. Typically, an over-supply of uranium together with national stockpiling at low prices resulted in depression of prices to less than $5 per pound by 1971. Although forecasts made in the early 1970's increased confidence in the future of nuclear power, and consequently the demand for uranium, prices remained low until the end of 1973 when OPEC announced a very large increase in oil prices and quite naturally, prices for coal also rose substantially. The economics of nuclear fuel immediately improved and prices for uranium began to climb in 1974. But the world-wide impact of the OPEC decision also produced negative effects on the uranium industry. Uranium production costs rose dramatically, as did capital costs, and money for investment in new uranium ventures became more scarce and more expensive. However, the uranium supply picture today offers hope of satisfactory development in spite of the many problems to be

Uranium Elemental and Isotopic Constraints on Groundwater Flow Beneath the Nopal I Uranium Deposit, Pena Blanca, Mexico

Energy Technology Data Exchange (ETDEWEB)

S.J. Goldstein; M.T. Murrell; A.M. Simmons

2005-07-11

The Nopal I uranium deposit in Chihuahua, Mexico, is an excellent analogue for evaluating the fate of spent fuel, associated actinides, and fission products over long time scales for the proposed Yucca Mountain high-level nuclear waste repository. In 2003, three groundwater wells were drilled directly adjacent to (PB-1) and 50 m on either side of the uranium deposit (PB-2 and PB-3) in order to evaluate uranium-series transport in three dimensions. After drilling, uranium concentrations were elevated in all of the three wells (0.1-18 ppm) due to drilling activities and subsequently decreased to {approx}5-20% of initial values over the next several months. The {sup 234}U/{sup 238}U activity ratios were similar for PB-1 and PB-2 (1.005 to 1.079) but distinct for PB-3 (1.36 to 1.83) over this time period, suggesting limited mixing between groundwater from these wells over these short time and length scales. Regional groundwater wells located up to several km from the deposit also have distinct uranium isotopic characteristics and constrain mixing over larger length and time scales. We model the decreasing uranium concentrations in the newly drilled wells with a simple one-dimensional advection-dispersion model, assuming uranium is introduced as a slug to each of the wells and transported as a conservative tracer. Using this model for our data, the relative uranium concentrations are dependent on both the longitudinal dispersion as well as the mean groundwater flow velocity. These parameters have been found to be correlated in both laboratory and field studies of groundwater velocity and dispersion (Klotz et al., 1980). Using typical relationships between velocity and dispersion for field and laboratory studies along with the relationship observed from our uranium data, both velocity (1-10 n/yr) and dispersion coefficient (1E-5 to 1E-2 cm{sup 2}/s) can be derived from the modeling. As discussed above, these relatively small flow velocities and dispersivities agree with

Uranium(VI) speciation by spectroscopy

International Nuclear Information System (INIS)

Meinrath, G.

1997-01-01

The application of UV-Vis and time-resolved laser-induced fluorescence (TRLF) spectroscopies to direct of uranium(VI) in environmental samples offers various prospects that have, however, serious limitations. While UV-Vis spectroscopy is probably not sensitive enough to detect uranium(VI) species in the majority of environmental samples, TRLFS is principially able to speciate uranium(VI) at very low concentration levels in the nanomol range. Speciation by TRLFS can be based on three parameters: excitation spectrum, emission spectrum and lifetime of the fluorescence emission process. Due to quenching effects, the lifetime may not be expected to be as characteristics as, e.g., the emission spectrum. Quenching of U(VI) fluorescence by reaction with organic substances, inorganic ions and formation of carbonate radicals is one important limiting factor in the application of U(VI) fluorescence spectroscopy. Fundamental photophysical criteria are illustrated using UV-Vis and fluorescence spectra of U(VI) hydrolysis and carbonato species as examples. (author)

Uranium exploration in Ecuador

International Nuclear Information System (INIS)

Severne, B.; Penaherrera, P.F.; Fiallos, V.S.

1981-01-01

The 600-km segment of the Andean Cordillera in Ecuador includes zones that can be correlated, geologically, with uranium districts elsewhere in the Andes. It is believed that these essentially unexplored zones have the potential for economic uranium mineralization. Exploration activity to date has been limited, although it has involved both geochemical and radiometric techniques to evaluate geological concepts. Minor uranium occurrences (with chemical analyses up to 100 ppm) have been encountered, which provide further incentive to commence large-scale systematic exploration. It is recognized that a very large exploration budget and considerable technical expertise will be required to ensure exploration success. Consequently, participation by groups of proven capability from other countries will be sought for Ecuador's national exploration programme. (author)

Methods for the estimation of uranium ore reserves

International Nuclear Information System (INIS)

1985-01-01

The Manual is designed mainly to provide assistance in uranium ore reserve estimation methods to mining engineers and geologists with limited experience in estimating reserves, especially to those working in developing countries. This Manual deals with the general principles of evaluation of metalliferous deposits but also takes into account the radioactivity of uranium ores. The methods presented have been generally accepted in the international uranium industry

Uranium as Raw Material for Nuclear Energy

International Nuclear Information System (INIS)

Lelek, V.

2006-01-01

There is lot of information bringing our attention to the problem of limited raw material resources. Fortunately uranium for nuclear energy is very concentrated source and that is why its transport brings no problems and could be realized from anywhere. Second question is if overall resources are available for current nuclear energy development. Data documenting reasons for nowadays price growth are presenting and it is clearly shown that the most probable explanation is that there is gap in new uranium mines preparation and the lot of smaller mines were closed in the period of low uranium prices. Conclusion is that there is at least for the first half of this century even for thermal reactors enough uranium. Situation could be changed if there will massive production of liquid fuel using hydrogen, produced through nuclear heating. Public information about former military uranium resources are also included. Contemporary about one half of US nuclear power-stations is using high enriched uranium diluted with natural uranium - it is expected to continue this way up to 2012. Uranium is complicated market (Authors)

Documentation of the Uranium Market Model (UMM)

International Nuclear Information System (INIS)

1989-01-01

The Uranium Market Model is used to make projections of activity in the US uranium mining and milling industry. The primary data sources were EIA, the Nuclear Assurance Corporation, and, to a lesser extent, Nuexco and Nuclear Resources International. The Uranium Market Model is a microeconomic simulation model in which uranium supplied by the mining and milling industry is provided to meet the demand for uranium by electric utilities with nuclear power plants. Uranium is measured on a U 3 O 8 (uranium oxide) equivalent basis. The model considers every major production center and utility on a worldwide basis (with Centrally Planned Economies considered in a limited way), and makes annual projections for each major uranium production and consumption region in the world. Typically, nine regions are used: the United States, Canada, Australia, South Africa, Other Africa, Europe, Latin America, the Far East, and Other. Production centers and utilities are identified as being in one of these regions. In general, the model can accommodate any user-provided set of regional definitions and data

Characterization of low concentration uranium glass working materials

Energy Technology Data Exchange (ETDEWEB)

Eppich, G. R. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Wimpenny, J. B. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Leever, M. E. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Knight, K. B. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Hutcheon, I. D. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Ryerson, F. J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2016-03-22

A series of uranium-doped silicate glasses were created at (Lawrence Livermore National Laboratory) LLNL, to be used as working reference material analogs for low uranium concentration research. Specifically, the aim of this effort was the generation of well-characterized glasses spanning a range of concentrations and compositions, and of sufficient homogeneity in uranium concentration and isotopic composition, for instrumentation research and development purposes. While the glasses produced here are not intended to replace or become standard materials for uranium concentration or uranium isotopic composition, it is hoped that they will help fill a current gap, providing low-level uranium glasses sufficient for methods development and method comparisons within the limitations of the produced glass suite. Glasses are available for research use by request.

Method for converting uranium oxides to uranium metal

Science.gov (United States)

Duerksen, Walter K.

1988-01-01

A process is described for converting scrap and waste uranium oxide to uranium metal. The uranium oxide is sequentially reduced with a suitable reducing agent to a mixture of uranium metal and oxide products. The uranium metal is then converted to uranium hydride and the uranium hydride-containing mixture is then cooled to a temperature less than -100.degree. C. in an inert liquid which renders the uranium hydride ferromagnetic. The uranium hydride is then magnetically separated from the cooled mixture. The separated uranium hydride is readily converted to uranium metal by heating in an inert atmosphere. This process is environmentally acceptable and eliminates the use of hydrogen fluoride as well as the explosive conditions encountered in the previously employed bomb-reduction processes utilized for converting uranium oxides to uranium metal.

Determination of uranium concentration in an ore sample using laser-induced breakdown spectroscopy

International Nuclear Information System (INIS)

Kim, Y.-S.; Han, B.-Y.; Shin, H.S.; Kim, H.D.; Jung, E.C.; Jung, J.H.; Na, S.H.

2012-01-01

Laser-induced breakdown spectroscopy (LIBS) has been recognized as a promising technique for analyzing sensitive nuclear materials such as uranium, plutonium, and curium in a high-radiation environment, especially since the implementation of IAEA (International Atomic Energy Agency) safeguards. The uranium spectra of ore samples were quantitatively analyzed prior to analyzing sensitive materials in the nuclear industry. The purpose of this experiment is to extract quantitative information about the uranium in a uranium ore using a standard addition approach. The uranium ore samples containing different concentrations of U were prepared by mixing raw ore powder with natural uranium oxide powders. Calibration sets of 0.2, 0.4, 0.6, 0.8 and 1.0 wt.% uranium concentrations within the uranium ore sample were achieved. A pulsed and Q-switched Nd:YAG laser at a wavelength of 532 nm was used as a light source. An echelle spectrometer that covers a 190–420 nm wavelength range is used to generate a calibration curve and determine the detection limit of uranium in the ore matrix. The neutral atomic-emission peak at a wavelength of 356.659 nm indicated a detection limit of ∼ 158 ppm for uranium, and the uranium concentration was determined in a raw ore sample that has an unknown quantity of uranium. - Highlights: ► The feasibility of LIBS application to monitor uranium element was carried out. ► The detection limit of U in ore was determined by a standard additional approach. ► Quantitative analyses of U concentration in a natural uranium ore were performed.

Uranium content measurement in drinking water samples using track etch technique

International Nuclear Information System (INIS)

Kumar, Mukesh; Kumar, Ajay; Singh, Surinder; Mahajan, R.K.; Walia, T.P.S.

2003-01-01

The concentration of uranium has been assessed in drinking water samples collected from different locations in Bathinda district, Punjab, India. The water samples are taken from hand pumps and tube wells. Uranium is determined using fission track technique. Uranium concentration in the water samples varies from 1.65±0.06 to 74.98±0.38 μg/l. These values are compared with safe limit values recommended for drinking water. Most of the water samples are found to have uranium concentration above the safe limit. Analysis of some heavy metals (Zn, Cd, Pb and Cu) in water is also done in order to see if some correlation exists between the concentration of uranium and these heavy metals. A weak positive correlation has been observed between the concentration of uranium and heavy metals of Pb, Cd and Cu

Uranium

International Nuclear Information System (INIS)

Cuney, M.; Pagel, M.; Leroy, J.

1992-01-01

First, this book presents the physico-chemical properties of Uranium and the consequences which can be deduced from the study of numerous geological process. The authors describe natural distribution of Uranium at different scales and on different supports, and main Uranium minerals. A great place in the book is assigned to description and classification of uranium deposits. The book gives also notions on prospection and exploitation of uranium deposits. Historical aspects of Uranium economical development (Uranium resources, production, supply and demand, operating costs) are given in the last chapter. 7 refs., 17 figs

Uranium

International Nuclear Information System (INIS)

Poty, B.; Cuney, M.; Bruneton, P.; Virlogeux, D.; Capus, G.

2010-01-01

With the worldwide revival of nuclear energy comes the question of uranium reserves. For more than 20 years, nuclear energy has been neglected and uranium prospecting has been practically abandoned. Therefore, present day production covers only 70% of needs and stocks are decreasing. Production is to double by 2030 which represents a huge industrial challenge. The FBR-type reactors technology, which allows to consume the whole uranium content of the fuel, is developing in several countries and will ensure the long-term development of nuclear fission. However, the implementation of these reactors (the generation 4) will be progressive during the second half of the 21. century. For this reason an active search for uranium ores will be necessary during the whole 21. century to ensure the fueling of light water reactors which are huge uranium consumers. This dossier covers all the aspects of natural uranium production: mineralogy, geochemistry, types of deposits, world distribution of deposits with a particular attention given to French deposits, the exploitation of which is abandoned today. Finally, exploitation, ore processing and the economical aspects are presented. Contents: 1 - the uranium element and its minerals: from uranium discovery to its industrial utilization, the main uranium minerals (minerals with tetravalent uranium, minerals with hexavalent uranium); 2 - uranium in the Earth's crust and its geochemical properties: distribution (in sedimentary rocks, in magmatic rocks, in metamorphic rocks, in soils and vegetation), geochemistry (uranium solubility and valence in magmas, uranium speciation in aqueous solution, solubility of the main uranium minerals in aqueous solution, uranium mobilization and precipitation); 3 - geology of the main types of uranium deposits: economical criteria for a deposit, structural diversity of deposits, classification, world distribution of deposits, distribution of deposits with time, superficial deposits, uranium

Uranium and drinking water; Uran und Trinkwasser

Energy Technology Data Exchange (ETDEWEB)

Konietzka, Rainer [Umweltbundesamt, Berlin (Germany). Fachgebiet II 3.6 - Toxikologie des Trink- und Badebeckenwassers; Dieter, Hermann H.

2014-03-01

Uranium is provoking public anxiety based on the radioactivity of several isotopes and the connection to nuclear technology. Drinking water contains at the most geogenic uranium in low concentrations that might be interesting in the frame of chemical of toxicology, but not due to radiological impact. The contribution gives an overview on the uranium content in drinking water and health effects for the human population based on animal tests. These experiments indicate a daily tolerable intake of 0.2 microgram per kg body mass. The actual limiting value for uranium in drinking water is 0.3 microgram per kg body mass water (drinking water regulation from 2001).

Ranger uranium project

International Nuclear Information System (INIS)

1979-01-01

This agreement between the Commonwealth of Australia, Peko-Wallsend Operations Ltd., Electrolytic Zinc Company of Australasia Limited, and the Australian Atomic Energy Commission sets out articles under which the Ranger uranium project in the Northern Territory of Australia is to be operated

URANIUM-SERIES CONSTRAINTS ON RADIONUCLIDE TRANSPORT AND GROUNDWATER FLOW AT NOPAL I URANIUM DEPOSIT, SIERRA PENA BLANCA, MEXICO

Energy Technology Data Exchange (ETDEWEB)

S. J. Goldstein, S. Luo, T. L. Ku, and M. T. Murrell

2006-04-01

Uranium-series data for groundwater samples from the vicinity of the Nopal I uranium ore deposit are used to place constraints on radionuclide transport and hydrologic processes at this site, and also, by analogy, at Yucca Mountain. Decreasing uranium concentrations for wells drilled in 2003 suggest that groundwater flow rates are low (< 10 m/yr). Field tests, well productivity, and uranium isotopic constraints also suggest that groundwater flow and mixing is limited at this site. The uranium isotopic systematics for water collected in the mine adit are consistent with longer rock-water interaction times and higher uranium dissolution rates at the front of the adit where the deposit is located. Short-lived nuclide data for groundwater wells are used to calculate retardation factors that are on the order of 1,000 for radium and 10,000 to 10,000,000 for lead and polonium. Radium has enhanced mobility in adit water and fractures near the deposit.

URANIUM-SERIES CONSTRAINTS ON RADIONUCLIDE TRANSPORT AND GROUNDWATER FLOW AT NOPAL I URANIUM DEPOSIT, SIERRA PENA BLANCA, MEXICO

International Nuclear Information System (INIS)

S. J. Goldstein, S. Luo, T. L. Ku, and M. T. Murrell

2006-01-01

Uranium-series data for groundwater samples from the vicinity of the Nopal I uranium ore deposit are used to place constraints on radionuclide transport and hydrologic processes at this site, and also, by analogy, at Yucca Mountain. Decreasing uranium concentrations for wells drilled in 2003 suggest that groundwater flow rates are low (< 10 m/yr). Field tests, well productivity, and uranium isotopic constraints also suggest that groundwater flow and mixing is limited at this site. The uranium isotopic systematics for water collected in the mine adit are consistent with longer rock-water interaction times and higher uranium dissolution rates at the front of the adit where the deposit is located. Short-lived nuclide data for groundwater wells are used to calculate retardation factors that are on the order of 1,000 for radium and 10,000 to 10,000,000 for lead and polonium. Radium has enhanced mobility in adit water and fractures near the deposit

Challenges of ICRP 60 for uranium refining and conversion facilities

International Nuclear Information System (INIS)

Takala, J.M.

1998-01-01

Cameco Corporation operates high-grade uranium mines in northern Saskatchewan and uranium refining and conversion facilities in Ontario. The dose limits for these and all other nuclear facilities in Canada are 50 mSv per year and 4 WLM per year, which are applied separately. However, the upcoming incorporation of the recommendations in ICRP 60 into the Canadian regulations will result in several important changes. In addition to a more restrictive dose limit, the new regulations will require that all radiation exposures be combined into a single index of exposure. Meeting the new lower dose limits of 50 mSv per year and 100 mSv per 5 years will not be a major problem at Cameco facilities. However, the incorporation of long-lived radioactive dust exposures into the dose calculation will be a major challenge. This will cause the most difficulty at the uranium refining and conversion facilities where much of the process involves handling a variety of uranium compounds in the form of a dry powder. At the uranium conversion facilities the control of exposure to airborne uranium is achieved through a combination of lung counting, urinalysis, and fixed area monitors. To progress from a system of exposure control to dose estimation to individual workers will require some major changes. (author)

Uranium market and resources

International Nuclear Information System (INIS)

Capus, G.; Arnold, T.

2005-01-01

Under the combined effect of various factors, such as interrogations related to facing the climatic changes, the increasing prices of oil versus announced decrease of its resources, the major geopolitical evolution and the remarkable development of Asia, we live nowadays a revival of nuclear power in the very front of stage. In tis context, the following question is posed: could the nuclear fission be a sustainable source of energy when taking into consideration the availability of uranium resources? The article aims at pinpointing the knowledge we have about the world uranium resources, their limits of uncertainty and the relation between knowledge resources and market evolution. To conclude, some susceptible tracks are proposed to improve the using process of uranium resources particularly in softening the impact of high prices

The uranium industry of Bulgaria

International Nuclear Information System (INIS)

Pool, T.C.

1991-01-01

For 45 years, the Bulgarian uranium industry operated behind an impenetrable veil of secrecy. As this veil is slowly lifted, the breadth and structure of the industry are becoming apparent-and so are the problems. Bulgaria's uranium industry began in 1945 with the evaluation of several uranium mineral occurrences in the Balkan Mountains. These occurrences provided to be mineable deposits and became the foundation for a continuing program of exploration and development. Mining commenced in 1946, and all production was exported under contract to the Soviet Union in exchange for an eventual supply of fabricated nuclear fuel. In concert with most other countries of the COMECON block, Bulgaria's exploration and development program reached its zenith in the late 1960s and early 1970s. Like other COMECON countries, the contract with the Soviet Union was reduced during the 1980s and finally terminated. The Bulgarian uranium industry now is under substantial pressure to: (1) Maintain uranium production as a base of support for its 10,000 employees. (2) Develop mineral deposits other than uranium as a replacement for high-cost uranium production. (3) Clean up past and present production sites, most of which have significant environmental problems. The probability of successfully completing these three tasks without outside assistance is limited. Bulgaria's almost complete dependence for four and a half decades on Soviet aid, contracts, and technology has taken its toll

Kinetics of the chain uranium decay

International Nuclear Information System (INIS)

Zel'dovich, Ya.B.; Khariton, Yu.B.

1984-01-01

The development of chain reaction in uranium mass, when passing through the mass critical value, is studied. It is shown that thermal expanson is a powerful regulating factor, making the limit passing quite safe. The case of convergence of two uranium masses of precritical dimensions is considered in particular. The critical mass value is assessed and it is shown that its gradual increase above the critical value results in the reaction vibrational regime with the period inversely proportional to the square root of uranium supply rate. The role of delaying neutrons in the fission chain reaction development is pointed out

Methods and measures of enhancing production capacity of uranium mines

International Nuclear Information System (INIS)

Ni Yuhui

2013-01-01

Limited by resource conditions and mining conditions, the production capacity of uranium mines is generally small. The main factors to affect the production capacity determination of uranium mines are analyzed, the ways and measures to enhance the production capacity of uranium mines are explored from the innovations of technology and management mode. (author)

The potential for criticality following disposal of uranium at low-level waste facilities: Uranium blended with soil

Energy Technology Data Exchange (ETDEWEB)

Toran, L.E.; Hopper, C.M.; Naney, M.T. [and others

1997-06-01

The purpose of this study was to evaluate whether or not fissile uranium in low-level-waste (LLW) facilities can be concentrated by hydrogeochemical processes to permit nuclear criticality. A team of experts in hydrology, geology, geochemistry, soil chemistry, and criticality safety was formed to develop achievable scenarios for hydrogeochemical increases in concentration of special nuclear material (SNM), and to use these scenarios to aid in evaluating the potential for nuclear criticality. The team`s approach was to perform simultaneous hydrogeochemical and nuclear criticality studies to (1) identify some achievable scenarios for uranium migration and concentration increase at LLW disposal facilities, (2) model groundwater transport and subsequent concentration increase via sorption or precipitation of uranium, and (3) evaluate the potential for nuclear criticality resulting from potential increases in uranium concentration over disposal limits. The analysis of SNM was restricted to {sup 235}U in the present scope of work. The outcome of the work indicates that criticality is possible given established regulatory limits on SNM disposal. However, a review based on actual disposal records of an existing site operation indicates that the potential for criticality is not a concern under current burial practices.

The potential for criticality following disposal of uranium at low-level waste facilities: Uranium blended with soil

International Nuclear Information System (INIS)

Toran, L.E.; Hopper, C.M.; Naney, M.T.

1997-06-01

The purpose of this study was to evaluate whether or not fissile uranium in low-level-waste (LLW) facilities can be concentrated by hydrogeochemical processes to permit nuclear criticality. A team of experts in hydrology, geology, geochemistry, soil chemistry, and criticality safety was formed to develop achievable scenarios for hydrogeochemical increases in concentration of special nuclear material (SNM), and to use these scenarios to aid in evaluating the potential for nuclear criticality. The team's approach was to perform simultaneous hydrogeochemical and nuclear criticality studies to (1) identify some achievable scenarios for uranium migration and concentration increase at LLW disposal facilities, (2) model groundwater transport and subsequent concentration increase via sorption or precipitation of uranium, and (3) evaluate the potential for nuclear criticality resulting from potential increases in uranium concentration over disposal limits. The analysis of SNM was restricted to 235 U in the present scope of work. The outcome of the work indicates that criticality is possible given established regulatory limits on SNM disposal. However, a review based on actual disposal records of an existing site operation indicates that the potential for criticality is not a concern under current burial practices

Non Destructive Analysis of Uranium by Radiometry

International Nuclear Information System (INIS)

Yusuf Nampira

2007-01-01

Uranium used in nuclear fuel development activity. the Substance use incurred by regulation safeguard. On that account in uranium acceptance conducted by verification of according to document by the specification of goods. Verification done by analysing performed uranium. The activity require by analyse method which simple and rapid analyses and has accurate result of analyses, is hence done by validation of non destructive uranium analysis that is with count gamma radiation from 235 U and product decay from 238 U. Quantitative analysis of uranium in substance determined by through count radiation-g at energy 185.72 keV and the use assess ratio of gamma radiation count from 235 U to 234 Pa to determine isotope content 235 U in substance. The result of analyses were given result of analysis with above correctness storey level 95% and have limit detect equivalent by 0.0174 mg U in U 3 O 8 . This method use at isotope uranium-235 analysis through count gamma radiation comparing method 235 U/ 234 Pa giving accuracy level 95% at sample equivalent uranium its content in 1 g uranium with isotope 235 U smaller than 75 weight percent. (author)

Uranium conversion

International Nuclear Information System (INIS)

Oliver, Lena; Peterson, Jenny; Wilhelmsen, Katarina

2006-03-01

FOI, has performed a study on uranium conversion processes that are of importance in the production of different uranium compounds in the nuclear industry. The same conversion processes are of interest both when production of nuclear fuel and production of fissile material for nuclear weapons are considered. Countries that have nuclear weapons ambitions, with the intention to produce highly enriched uranium for weapons purposes, need some degree of uranium conversion capability depending on the uranium feed material available. This report describes the processes that are needed from uranium mining and milling to the different conversion processes for converting uranium ore concentrate to uranium hexafluoride. Uranium hexafluoride is the uranium compound used in most enrichment facilities. The processes needed to produce uranium dioxide for use in nuclear fuel and the processes needed to convert different uranium compounds to uranium metal - the form of uranium that is used in a nuclear weapon - are also presented. The production of uranium ore concentrate from uranium ore is included since uranium ore concentrate is the feed material required for a uranium conversion facility. Both the chemistry and principles or the different uranium conversion processes and the equipment needed in the processes are described. Since most of the equipment that is used in a uranium conversion facility is similar to that used in conventional chemical industry, it is difficult to determine if certain equipment is considered for uranium conversion or not. However, the chemical conversion processes where UF 6 and UF 4 are present require equipment that is made of corrosion resistant material

Uranium exploration in India: present status and future strategies

International Nuclear Information System (INIS)

Maithani, P.B.

2011-01-01

Exploration for Uranium in India dates back to 1949, where surveys to locate atomic minerals were initiated in the well established Copper Thrust Belt (CTB) of Singhbhum, in the present day Jharkhand state. Based on the limited understanding on uranium geology, the thrust zones of Singhbhum which were popularly known for hosting Copper mineralization were targeted presuming sympathetic relation between Copper and Uranium. Exploration for uranium over the past six decades has resulted in identifying eleven major uranium deposits distributed in varied geological environs all over the country. Apart from conventional uranium mineralization, non-conventional resources like phosphorite, black shale etc. have immense potential. Even though their uranium grades will be of lower order, their uranium content will be huge due to their extensive size. In addition to intensifying uranium exploration in potential geological domains, AMD also plans to tap the non-conventional resources which will add substantially to the resource base

Determination of uranium metal concentration in irradiated fuel storage basin sludge using selective dissolution

International Nuclear Information System (INIS)

Delegard, C.H.; Sinkov, S.I.; Chenault, J.W.; Schmidt, A.J.; Pool, K.N.; Welsh, T.L.

2014-01-01

Irradiated uranium metal fuel was stored underwater in the K East and K West storage basins at the US Department of Energy Hanford Site. The uranium metal under damaged cladding reacted with water to generate hydrogen gas, uranium oxides, and spalled uranium metal particles which intermingled with other particulates to form sludge. While the fuel has been removed, uranium metal in the sludge remains hazardous. An expeditious routine method to analyze 0.03 wt% uranium metal in the presence of >30 wt% total uranium was needed to support safe sludge management and processing. A selective dissolution method was designed based on the rapid uranium oxide dissolution but very low uranium metal corrosion rates in hot concentrated phosphoric acid. The uranium metal-bearing heel from the phosphoric acid step then is rinsed before the uranium metal is dissolved in hot concentrated nitric acid for analysis. Technical underpinnings of the selective dissolution method, including the influence of sludge components, were investigated to design the steps and define the reagents, quantities, concentrations, temperatures, and times within the selective dissolution analysis. Tests with simulant sludge proved the technique feasible. Tests with genuine sludge showed a 0.0028 ± 0.0037 wt% (at one standard deviation) uranium metal analytical background, a 0.011 wt% detection limit, and a 0.030 wt% quantitation limit in settled (wet) sludge. In tests using genuine K Basin sludge spiked with uranium metal at concentrations above the 0.030 wt% ± 25 % (relative) quantitation limit, uranium metal recoveries averaged 99.5 % with a relative standard deviation of 3.5 %. (author)

Machining of uranium and uranium alloys

International Nuclear Information System (INIS)

Morris, T.O.

1981-01-01

Uranium and uranium alloys can be readily machined by conventional methods in the standard machine shop when proper safety and operating techniques are used. Material properties that affect machining processes and recommended machining parameters are discussed. Safety procedures and precautions necessary in machining uranium and uranium alloys are also covered. 30 figures

Uranium recovery from slags of metallic uranium

International Nuclear Information System (INIS)

Fornarolo, F.; Frajndlich, E.U.C.; Durazzo, M.

2006-01-01

The Center of the Nuclear Fuel of the Institute of Nuclear Energy Research - IPEN finished the program of attainment of fuel development for research reactors the base of Uranium Scilicet (U 3 Si 2 ) from Hexafluoride of Uranium (UF 6 ) with enrichment 20% in weight of 235 U. In the process of attainment of the league of U 3 Si 2 we have as Uranium intermediate product the metallic one whose attainment generates a slag contend Uranium. The present work shows the results gotten in the process of recovery of Uranium in slags of calcined slags of Uranium metallic. Uranium the metallic one is unstable, pyrophoricity and extremely reactive, whereas the U 3 O 8 is a steady oxide of low chemical reactivity, what it justifies the process of calcination of slags of Uranium metallic. The calcination of the Uranium slag of the metallic one in oxygen presence reduces Uranium metallic the U 3 O 8 . Experiments had been developed varying it of acid for Uranium control and excess, nitric molar concentration gram with regard to the stoichiometric leaching reaction of temperature of the leaching process. The 96,0% income proves the viability of the recovery process of slags of Uranium metallic, adopting it previous calcination of these slags in nitric way with low acid concentration and low temperature of leaching. (author)

Uranium, depleted uranium, biological effects; Uranium, uranium appauvri, effets biologiques

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-07-01

Physicists, chemists and biologists at the CEA are developing scientific programs on the properties and uses of ionizing radiation. Since the CEA was created in 1945, a great deal of research has been carried out on the properties of natural, enriched and depleted uranium in cooperation with university laboratories and CNRS. There is a great deal of available data about uranium; thousands of analyses have been published in international reviews over more than 40 years. This presentation on uranium is a very brief summary of all these studies. (author)

Uranium mining, atomic weapons testing, nuclear waste storage: A global survey. World Uranium Hearing grey book 1992

International Nuclear Information System (INIS)

Krumbholz, E.; Kressing, F.

1992-09-01

The first edition of the 'World Uranium Hearing Grey Book' for the World Uranium Hearing in Salzburg, 13-19 September 1992 is meant to be a reference for people involved in the World Uranium Hearing. It is mostly made up to country by country surveys giving background information on the testimonies presented at the Hearing, and on many more cases. Included are two short articles: One on 'nukespeak' to make the reader aware of how the language of the nuclear industry influences our speaking and thinking; and an article on the wastes produced by uranium mines. Due to limited time and resources this documentation is not complete. Many questions remain. For example, information is rare about conditions in Eastern Europe. Also, some countries are given much more space than others, which does not indicate importance or seriousness of implications of uranium mining, weapons testing or nuclear waste storage in this particular country. (orig./HP)

The uranium supply strategy of China

International Nuclear Information System (INIS)

Gao, S.

2014-01-01

Currently there are 28 units of nuclear power plants (NPPs) under construction in China. Most of these plants will be put into operation sequentially in a couple years. The paper will present the operational and construction status of NPPs in China. As the reactor fleet increases, the requirement for uranium will also substantially increase. Due to declining air quality, as atmospheric pollution spreads rapidly from northern parts to southern parts of China, the option to develop nuclear power has become the highest priority. Uranium demand will be the key to support the expanded nuclear power in the future. Current and future requirements of uranium and the envisaged supply strategy will be discussed. Domestic production is seen as one of the channels to meet the increased requirement. As the uranium price remain low, there will be limited the expansion of domestic production in the short term. The exploration of economic resources is being promoted. Decreasing production costs is mandated in operations due to low uranium prices at present. Development of overseas uranium resources is another channel to supply for the NPPs. Through acquisition of uranium mining projects, advanced uranium projects and exploration projects, China can meet the requirement of NPPs in the long-term. Joint venture partnership is also flexible option for developing uranium resources overseas. Purchasing uranium in the market is the third option. Complementing the supply by domestic production and overseas development, purchase of uranium product in the market is a simple and easy option. Advantages and disadvantages of these three channels and how these can be combined into an integrated strategy of supply and the proprotionate weightage of each channel for the potential future supply of uranium to the NNP fleet will be discussed. (author)

Technology assessment of in situ uranium mining

International Nuclear Information System (INIS)

Cowan, C.E.

1981-01-01

The objective of the PNL portion of the Technology Assessment project is to provide a description of the current in situ uranium mining technology; to evaluate, based on available data, the environmental impacts and, in a limited fashion, the health effects; and to explore the impediments to development and deployment of the in situ uranium mining technology

Sorption of uranium on rocks in anaerobic groundwater

International Nuclear Information System (INIS)

Hakanen, M.

1992-12-01

Spent nuclear fuel contains substantial amounts of long lived isotopes of actinoide elements, the most abundant of which is the oxide from uranium in the fuel matrix. The behaviour of uranium, also present in small concentrations in natural rocks and waters, is redox sensitive. The concentration controlling mechanisms in groundwaters of uranium are not well-known. In this work a series of laboratory experiments was made to study the redox and sorption behaviour of uranium under anaerobic conditions. The experiments indicated that a part of uranium(VI) was reduced to uranium(IV). The sorbed uranium was of mixed oxidation states. The redox potential of water was not an appropriate indicator of the U(IV)/U(VI) ratio. Spiking of the water with the U(IV) was followed by very strong sorption. The derived lower limit (conservative) and the realistic mass distribution ratios (R d ) for U(IV) are 0.7 m 3 /kg and 3.5 m 3 /kg. (orig.)

Irradiation Stability of Uranium Alloys at High Exposures

International Nuclear Information System (INIS)

McDonell, W.R.

2001-01-01

Postirradiation examinations were begun of a series of unrestrained dilute uranium alloy specimens irradiated to exposures up to 13,000 MWD/T in NaK-containing stainless steel capsules. This test, part of a program of development of uranium metal fuels for desalination and power reactors sponsored by the Division of Reactor Development and Technology, has the objective of defining the temperature and exposure limits of swelling resistance of the alloyed uranium. This paper discusses those test results

X-ray topography of uranium alloys; Topographie aux rayons X d'alliages d'uranium

Energy Technology Data Exchange (ETDEWEB)

Le Naour, L [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1968-07-01

A description of the structure of uranium alloys has been made using the data obtained by X-ray diffraction techniques derived from the Berg-Barrette method. In the first.stage the use of a monochromatic beam of X-rays having a very low divergence makes it possible to obtain very reproducible and exact numerical data concerning the grain and sub-grain sizes, and also the distribution of the sizes. It is thereby possible to detect any disorientation greater than 30 seconds of arc.The results obtained have been completed using a variable incidence device which- gives simultaneously an overall picture of a grain and an idea of the importance of internal disorientations; a more rigorous measurement of this latter parameter is then deduced from the Debye-Scherrer diagrams obtained using a fine-focus equipment. Observations are carried out on various one-phase or two phase uranium alloys which are compared successively to technical and to high-purity uranium. It is shown that the use of X-ray topographies, although limited in certain respects, allows a quantitative characterization of the structure. (author) [French] Une description des structures d'alliages d'uranium a ete faite a partir des donnees fournies par des techniques de diffraction de rayons X derivees de la methode de BERG--BARRETT. Dans une premiere etape, l'utilisation d'un faisceau de rayons X monochromatique et de tres faible divergence permet d'obtenir des donnees numeriques precises et tres reproductibles, relatives aux dimensions des grains, des sous-grains et a la distribution de ces grandeurs. Toute desorientation superieure a 30 secondes d'arc peut ainsi etre decelee. Les resultats obtenus ont ete completes en utilisant un montage a incidence variable, qui fournit simultanement l'image globale d'un grain et l'ordre de grandeur des desorientations internes; une mesure plus rigoureuse de ce dernier parametre se deduit ensuite de diagrammes DEBYE SHERRER realises avec un montage a foyer fin. Des

Uranium exports could match oil imports

International Nuclear Information System (INIS)

McIntyre, H.C.

1977-01-01

Apart from a temporary embargo while safeguards are negotiated, the Canadian government limits uranium exports so as to guarantee fuel for every Canadian reactor built or planned for 30 years. On the basis of present known reserves of 172 Gg of 'cheap' U 3 O 8 and 33 of 'dear', that would mean phasing out exports after the mid 1980's, but probably much more 'dear' uranium remains to be discovered. Provincial taxation and restrictions on foreign ownership may be limitations. Discoveries range over eleven areas, but production capacity at present is 14190 Mg/d from Ontario and 3400 from Saskatchewan, with 8800 mothballed and 4860 planned or being rehabilitated. The price has jumped to $95/kg, so that uranium exports may cover half the cost of oil imports. All producers use sulfuric acid leaching, except Eldorado, which uses carbonate leaching; a process using tertiary amine is being developed. Development of the organic-cooled Th/ 233 U fuelled reactor may greatly extend fuel resources. (N.D.H.)

Automated fluorometer for uranium analysis

International Nuclear Information System (INIS)

McElhaney, R.J.; Caylor, J.D.; Cole, S.H.; Futrell, T.L.; Giles, V.M.

1978-03-01

An utomated fluorometer has proven to be a valuable analytical tool for analyzing natural waters for the Uranium Resource Evaluation (URE) project. Uranium is isolated from potential quenching ions and concentrated by extraction with tri-n-octylphosphine oxide (TOPO) in Varsol. A portion of the extract is placed on a sodium fluoride pellet which is then dried, sintered, and cooled. Sixteen samples can be analyzed in about 1.5 hours. The lower reporting limit has been set at 0.20 micrograms per liter

Liquid uranium contaimment in refractories metals

International Nuclear Information System (INIS)

Duarte, J.L.; Padilha, A.F.

1982-01-01

Tests were performed on metalic materials for liquid uranium containment up to 2100 0 C. The materials Nb, Mo, Ta and W in the form of crucibles were tested at 2100 0 C for one hour in the presence of flowing argon. After testing, the crucibles were etched using HCl and analysed by optical metallography and electron proble microanalysis. The results are discussed in terms of Berthoud equation and indicated that the solubility limit of the crucible material in uranium at the temperature controlls the crucible dissolution by liquid uranium. The various phases formed, the mechanism of dissolution and the possible material for future use are presented and discussed. (Author) [pt

Fluorimetric determination of uranium in zirconium and zircaloy alloys

International Nuclear Information System (INIS)

Acosta L, E.

1991-05-01

The objective of this procedure is to determine microquantities of uranium in zirconium and zircaloy alloys. The report also covers the determination of uranium in zirconium alloys and zircaloy in the range from 0.25 to 20 ppm on 1 g of base sample of radioactive material. These limit its can be variable if the size of the used aliquot one is changed for the final determination of uranium. (Author)

Possible uranium sources of Streltsovsky uranium ore field

International Nuclear Information System (INIS)

Zhang Lisheng

2005-01-01

The uranium deposit of the Late Jurassic Streltsovaky caldera in Transbaikalia of Russia is the largest uranium field associated with volcanics in the world, its uranium reserves are 280 000 t U, and it is the largest uranium resources in Russia. About one third of the caldera stratigraphic pile consists of strongly-altered rhyolites. Uranium resources of the Streltsovsky caldera are much larger than any other volcanic-related uranium districts in the world. Besides, the efficiency of hydrothermal alteration, uranium resources appear to result from the juxtaposition of two major uranium sources; highly fractionated peralkaline rhyolites of Jurassic age in the caldera, and U-rich subalkaline granites of Variscan age in the basement in which the major uranium-bearing accessory minerals were metamict at the time of the hydrothermal ore formation. (authors)

Process for continuous production of metallic uranium and uranium alloys

Science.gov (United States)

Hayden, Jr., Howard W.; Horton, James A.; Elliott, Guy R. B.

1995-01-01

A method is described for forming metallic uranium, or a uranium alloy, from uranium oxide in a manner which substantially eliminates the formation of uranium-containing wastes. A source of uranium dioxide is first provided, for example, by reducing uranium trioxide (UO.sub.3), or any other substantially stable uranium oxide, to form the uranium dioxide (UO.sub.2). This uranium dioxide is then chlorinated to form uranium tetrachloride (UCl.sub.4), and the uranium tetrachloride is then reduced to metallic uranium by reacting the uranium chloride with a metal which will form the chloride of the metal. This last step may be carried out in the presence of another metal capable of forming one or more alloys with metallic uranium to thereby lower the melting point of the reduced uranium product. The metal chloride formed during the uranium tetrachloride reduction step may then be reduced in an electrolysis cell to recover and recycle the metal back to the uranium tetrachloride reduction operation and the chlorine gas back to the uranium dioxide chlorination operation.

Process for continuous production of metallic uranium and uranium alloys

Science.gov (United States)

Hayden, H.W. Jr.; Horton, J.A.; Elliott, G.R.B.

1995-06-06

A method is described for forming metallic uranium, or a uranium alloy, from uranium oxide in a manner which substantially eliminates the formation of uranium-containing wastes. A source of uranium dioxide is first provided, for example, by reducing uranium trioxide (UO{sub 3}), or any other substantially stable uranium oxide, to form the uranium dioxide (UO{sub 2}). This uranium dioxide is then chlorinated to form uranium tetrachloride (UCl{sub 4}), and the uranium tetrachloride is then reduced to metallic uranium by reacting the uranium chloride with a metal which will form the chloride of the metal. This last step may be carried out in the presence of another metal capable of forming one or more alloys with metallic uranium to thereby lower the melting point of the reduced uranium product. The metal chloride formed during the uranium tetrachloride reduction step may then be reduced in an electrolysis cell to recover and recycle the metal back to the uranium tetrachloride reduction operation and the chlorine gas back to the uranium dioxide chlorination operation. 4 figs.

Final Technical Report - In-line Uranium Immunosensor

International Nuclear Information System (INIS)

Blake, Diane A.

2006-01-01

In this project, personnel at Tulane University and Sapidyne Instruments Inc. developed an in-line uranium immunosensor that could be used to determine the efficacy of specific in situ biostimulation approaches. This sensor was designed to operate autonomously over relatively long periods of time (2-10 days) and was able to provide near real-time data about uranium immobilization in the absence of personnel at the site of the biostimulation experiments. An alpha prototype of the in-line immmunosensor was delivered from Sapidyne Instruments to Tulane University in December of 2002 and a beta prototype was delivered in November of 2003. The beta prototype of this instrument (now available commercially from Sapidyne Instruments) was programmed to autonomously dilute standard uranium to final concentrations of 2.5 to 100 nM (0.6 to 24 ppb) in buffer containing a fluorescently labeled anti-uranium antibody and the uranium chelator, 2,9-dicarboxyl-1,10-phenanthroline. The assay limit of detection for hexavalent uranium was 5.8 nM or 1.38 ppb. This limit of detection is well below the drinking water standard of 30 ppb recently promulgated by the EPA. The assay showed excellent precision; the coefficients of variation (CV's) in the linear range of the assay were less than 5% and CV?s never rose above 14%. Analytical recovery in the immunosensors-based assay was assessed by adding variable known quantities of uranium to purified water samples. A quantitative recovery (93.75% - 108.17%) was obtained for sample with concentrations from 7.5 to 20 nM (2-4.75 ppb). In August of 2005 the sensor was transported to Oak Ridge National Laboratory, for testing of water samples at the Criddle test site (see Wu et al., Environ. Sci. Technol. 40:3978-3985 2006 for a description of this site). In this first on-site test, the in-line sensor was able to accurately detect changes in the concentrations of uranium in effluent samples from this site. Although the absolute values for the uranium

Uranium in groundwater--Fertilizers versus geogenic sources.

Science.gov (United States)

Liesch, Tanja; Hinrichsen, Sören; Goldscheider, Nico

2015-12-01

Due to its radiological and toxicological properties even at low concentration levels, uranium is increasingly recognized as relevant contaminant in drinking water from aquifers. Uranium originates from different sources, including natural or geogenic, mining and industrial activities, and fertilizers in agriculture. The goal of this study was to obtain insights into the origin of uranium in groundwater while differentiating between geogenic sources and fertilizers. A literature review concerning the sources and geochemical processes affecting the occurrence and distribution of uranium in the lithosphere, pedosphere and hydrosphere provided the background for the evaluation of data on uranium in groundwater at regional scale. The state of Baden-Württemberg, Germany, was selected for this study, because of its hydrogeological and land-use diversity, and for reasons of data availability. Uranium and other parameters from N=1935 groundwater monitoring sites were analyzed statistically and geospatially. Results show that (i) 1.6% of all water samples exceed the German legal limit for drinking water (10 μg/L); (ii) The range and spatial distribution of uranium and occasional peak values seem to be related to geogenic sources; (iii) There is a clear relation between agricultural land-use and low-level uranium concentrations, indicating that fertilizers generate a measurable but low background of uranium in groundwater. Copyright © 2015 Elsevier B.V. All rights reserved.

Fluorometric analysis for uranium in natural waters

International Nuclear Information System (INIS)

Waterbury, G.R.

1977-01-01

A fluorometric method is used for the routine determination of uranium at 0.2 to parts-per-billion (ppB) concentrations in natural surface waters. Duplicate 200-μl aliquots of the water samples are pipetted onto 0.4-g pellets of 98 percent NaF-2 percent LiF flux contained in platinum dishes. The pellets are dried under heat lamps and fused over special propane burners. The fused pellets are subjected to ultraviolet radiation and the fluorescence is measured in a fluorometer. The lower limit of detection is 0.2 ppB of uranium, and the precision is about 15 relative percent in the 0.2 to 10 ppB uranium concentration range. Two analysts determine uranium in 750 to 900 samples per week using this method. Samples containing solids or more than 19 ppB of uranium are analyzed by a delayed neutron counting method

Uranium exploration of Samar Island

International Nuclear Information System (INIS)

Santos, G. Jr.

1979-02-01

Uranium exploration is being undertaken to meet the requirements of the Philippine Nuclear Power Plant-1 (PNPP-1) programmed to operate in 1982, for about 140 metric tons annually or 2664 MT of U 3 O 8 up to the year 2000. Samar was chosen as the survey pilot project and the method used was a geochemical reconnaissance or low density observation survey to delineate broad areas where follow-up uranium surveys may be undertaken. Stream sediments or surface waters were collected at each sampling point at a density of one sample per 20-25 sq. km. The conductance and pH of the water were measured with a conductivity meter and pH respectively. Radioactivity was determined using a portable scintillometer. The stream sediment and heavy mineral samples were analyzed for uranium (U), copper (CCu), lead (Pb), zinc (Zn), manganese (Mn), silver (Ag), cobalt (Co), nickel (Ni). Water samples were analyzed for uranium only. The solid samples were digested in an acid mixture of 85% concentrated nitric acid and 15% concentrated hydrochloric acid, and the leachable uranium was determined using a fluorimeter. The detection limits for uranium were 0.3 ppb and 0.3 ppm for water and solid samples, respectively. Analysis for Cu, Pb, Zn, Mn, Ag, Co, and Ni were done by Atomic Absorption Spectrophotometry using the same leaching solution prepared for uranium analysis. Over 9000 determinations were done on nearly 1600 samples. The survey delineated at least two areas where follow-up surveys for uranium are warranted. These areas are the San Isidro - Catarman in Northwestern Samar, and the vicinity of Bagacay mines in Central Samar

Study of the Formation of Eutectic Melt of Uranium and Thermal Analysis for the Salt Distillation of Uranium Deposits

International Nuclear Information System (INIS)

Park, Sung Bin; Hwang, Sung Chan; Kang, Young Ho; Park, Ki Min; Jun, Wan Gi; Lee, Han Soo; Cho, Dong Wook

2010-01-01

Uranium deposits from an electrorefining process contain about 30% salt. In order to recover pure uranium and transform it into an ingot, the salts have to be removed from the uranium deposits. Major process variables for the salt distillation process of the uranium deposits are hold temperature and vacuum pressure. Effects of the variables on the salt removal efficiency were studied in the previous study 1. By applying the Hertz-Langmuir relation to the salt evaporation of the uranium deposits, the evaporation coefficients were obtained at the various conditions. The operational conditions for achieving above 99% salt removal were deduced. The salt distilled uranium deposits tend to form the eutectic melt with iron, nickel, chromium for structural material of salt evaporator. In this study, we investigated the hold temperature limitation in order to prevent the formation of the eutectic melt between uranium and other metals. The reactions between the uranium metal and stainless steel were tested at various conditions. And for enhancing the evaporation rate of the salt and the efficient recovery of the distilled salt, the thermal analysis of the salt distiller was conducted by using commercial CFX software. From the thermal analysis, the effect of Ar gas flow on the evaporation of the salt was studied.

Analyses of uranium in some phosphate commercial products

International Nuclear Information System (INIS)

Kamel, N.H.M.; Sohsah, M.; Mohammad, H.M.; Sadek, M.

2005-01-01

The raw materials used in manufacturing of phosphate fertilizer products were derived from rocks. Rocks contain a remarkable of natural radioactivity. Uranium and phosphorous were originally initiated at the same time of the initiated rocks. The purpose of this research is to investigate solubility of uranium phosphate species at the phosphate fertilizer samples, samples including; raw phosphate material, single super phosphates (SSP) granules and powdered, triple super phosphates (TSP) and phosphogypsum samples were obtained from Abu-Zabal factory in Egypt. Solubility of uranium phosphate species was estimated. It was found that, less than half of the uranium phosphate species are soluble in water. The soluble uranium may be enter into the food chains by plant. Therefore, restriction should be done in order to limit contamination of land and the public

Jabiluka gold-uranium project

International Nuclear Information System (INIS)

1988-01-01

The Jabiluka gold-uranium deposit, 230km east of Darwin in the Alligator Rivers Region of the Northern Territory, was discovered by Pancontinental Mining Limited in 1971. Jabiluka, with reserves in excess of 200,000 tonnes of contained U 3 O 8 in two deposits 500 metres apart, is the world's largest high grade uranium deposit and also contains nearly 12 tonnes of gold. It is proposed that only the larger deposit, Jabiluka II will be mined - by underground extraction methods, and that 275,000 tonnes of ore per year will be mined and processed to produce 1,500 tonnes of U 3 O 8 and up to 30,000 oz of gold. The revenue from the uranium sales is estimated to be of the order of A$100 million per year at A$30/lb. By the end of 1982 all necessary mining and environmental approvals had been obtained and significant marketing progress made. With the Australian Labor Party winning Commonwealth Government in the 1983 election, Pancontinental's permission to seek sales contracts was withdrawn and development of the Jabiluka deposit ceased. Jabiluka remains undeveloped - awaiting a change in Australian Government policy on uranium. figs., maps

Government influence on international trade in uranium

International Nuclear Information System (INIS)

1978-01-01

The subject is dealt with in sections, entitled; introduction (history of uncertainty in the uranium market, opposition to nuclear power); unsatisfactory features of today's trade conditions (including discussion of restrictions in production, exports and imports); desirable principles governing international trade in uranium, apart from the non-proliferation issue (limitation on governmental intervention for economic purposes, reservation of adequate uranium resources in exporting countries, government export price control); desirable principles for achieving balance between security of supply and non-proliferation (need for consensus, reprocessing and fast breeder reactors, principles guiding government controls established for non-proliferation purposes). (U.K.)

Ultratrace Uranium Fingerprinting with Isotope Selective Laser Ionization Spectrometry

International Nuclear Information System (INIS)

Ziegler, Summer L.; Bushaw, Bruce A.

2008-01-01

Uranium isotope ratios can provide source information for tracking uranium contamination in a variety of fields, ranging from occupational bioassay to monitoring aftereffects of nuclear accidents. We describe the development of Isotope Selective Laser Ionization Spectrometry (ISLIS) for ultratrace measurement of the minor isotopes 234U, 235U, and 236U with respect to 238U. Optical isotopic selectivity in three-step excitation with single-mode continuous wave lasers is capable of measuring the minor isotopes at relative abundances below 1 ppm, and is not limited by isobaric interferences such as 235UH+ during measurement of 236U. This relative abundance limit approaches the threshold for measurement of uranium minor isotopes with conventional mass spectrometry, typically 10-7, but without mass spectrometric analysis of the laser-created ions. Uranyl nitrate standards from an international blind comparison were used to test analytical performance for different isotopic compositions and with quantities ranging from 11 ng to 10 (micro)g total uranium. Isotopic ratio determination was demonstrated over a linear dynamic range of 7 orders of magnitude with a few percent relative precision and detection limits below 500 fg for the minor isotopes

The fluorimetry for control of internal contamination of exposed workers to natural and enriched uranium

International Nuclear Information System (INIS)

Gaburo, J.C.; Todo, A.S.; Sordi, G.M.A.A.

2000-01-01

This study is a part of bioassay program revision applied to the uranium processing plants at IPEN-CNEN/SP. The workers of these facilities handle both natural uranium and uranium compounds with different isotopic composition which could reach up to 20% in 235 U. The most commonly employed techniques for the determination of uranium in urine at IPEN are fluorimetry and alpha spectrometry with detection limit of 1.0 mgL-1. and 1,0 mBqL-1 , respectively. Based in advantages and disadvantages of each technique it is very important to identify the workers groups that should be submitted for these analysis. In this report a limiting value of uranium concentration in urine, mgL-1, obtained by fluorimetry is proposed. All the results greater than these limiting value indicate the necessity to carry out a additional measurement by alpha spectroscopy. The uranium mass that result in a pre-determined limit committed effective dose is function of isotopic composition. Consequently, the predicted value of the measured of urinary excretion is function of isotopic composition also and depends of absorption characteristics when inhaled and of the monitoring interval considered. In this report the uranium concentration values for reference levels and limits doses are determined. Based on these results the procedures to use the fluorimetry or both fluorimetry and alpha-spectrometry were adopted. (author)

International Uranium Resources Evaluation Project (IUREP) national favourability studies: Bahrain

International Nuclear Information System (INIS)

1977-11-01

Bahrain consists of limestone, sandstone and marl of Cretaceous and Tertiary ages. The potential for discoveries of uranium is very limited and thus the Speculative potential is placed in the category of less than 1000 tonnes uranium. (author)

Recovery of uranium from crude uranium tetrafluoride

Energy Technology Data Exchange (ETDEWEB)

Ghosh, S K; Bellary, M P; Keni, V S [Chemical Engineering Division, Bhabha Atomic Research Centre, Mumbai (India)

1994-06-01

An innovative process has been developed for recovery of uranium from crude uranium tetrafluoride cake. The process is based on direct dissolution of uranium tetrafluoride in nitric acid in presence of aluminium hydroxide and use of solvent extraction for removal of fluorides and other bulk impurities to make uranium amenable for refining. It is a simple process requiring minimum process step and has advantage of lesser plant corrosion. This process can be applied for processing of uranium tetrafluoride generated from various sources like uranium by-product during thorium recovery from thorium concentrate, first stage product of uranium recovery from phosphoric acid by OPPA process and off grade uranium tetrafluoride material. The paper describes the details of the process developed and demonstrated on bench and pilot scale and its subsequent modification arising out of bulky solid waste generation. The modified process uses a lower quantity of aluminium hydroxide by allowing a lower dissolution of uranium per cycle and recycles the undissolved material to the next cycle, maintaining the overall recovery at high level. This innovation has reduced the solid waste generated by a factor of four at the cost of a slightly larger dissolution vessel and its increased corrosion rate. (author). 4 refs., 1 fig., 3 tabs.

Recovery of uranium from crude uranium tetrafluoride

International Nuclear Information System (INIS)

Ghosh, S.K.; Bellary, M.P.; Keni, V.S.

1994-01-01

An innovative process has been developed for recovery of uranium from crude uranium tetrafluoride cake. The process is based on direct dissolution of uranium tetrafluoride in nitric acid in presence of aluminium hydroxide and use of solvent extraction for removal of fluorides and other bulk impurities to make uranium amenable for refining. It is a simple process requiring minimum process step and has advantage of lesser plant corrosion. This process can be applied for processing of uranium tetrafluoride generated from various sources like uranium by-product during thorium recovery from thorium concentrate, first stage product of uranium recovery from phosphoric acid by OPPA process and off grade uranium tetrafluoride material. The paper describes the details of the process developed and demonstrated on bench and pilot scale and its subsequent modification arising out of bulky solid waste generation. The modified process uses a lower quantity of aluminium hydroxide by allowing a lower dissolution of uranium per cycle and recycles the undissolved material to the next cycle, maintaining the overall recovery at high level. This innovation has reduced the solid waste generated by a factor of four at the cost of a slightly larger dissolution vessel and its increased corrosion rate. (author)

The health dangers of uranium mining and jurisdictional questions

International Nuclear Information System (INIS)

Young, E.R.; Woollard, R.F.

1980-08-01

Uranium mining and milling presents a danger to the health of workers from gamma radiation, radon and thoron daughters, uranium oxides, and dust. The public is threatened by radon products, short and long term tailings failures, radium, uranium, and other chemicals. Present dose limits to workers and the public exposed to radiation from all stages of the nuclear fuel cycle have been set by organizations with vested interests in the nuclear industry and are too high. Uranium workers have in the past been poorly monitored and protected against radiation and other occupational hazards. Uranium tailings disposal methods at present are not adequate; tailings will remain hazardous for tens of thousands of years and will probably require deep geologic disposal. The non-substitutable end uses of uranium are nuclear power and nuclear weapons production, both of which have entirely unacceptable health effects

Challenges: which uranium for tomorrow?

International Nuclear Information System (INIS)

Bidaud, A.; Heuer, D.; Merle Lucotte, E.; Criqui, P.; Menanteau, Ph.; David, S.; Wilson, J.; Pagel, M.

2009-01-01

The author notices that the known reserves of uranium should be sufficient to supply existing reactors and new water reactors for the next decades, and that fuel recycling and reactor improvements as well as regenerator reactors should limit the pressure on these reserves. This means that nuclear physics and economics are in close relationship, that which can lead to the definition of several scenarios. They outline the importance of exploration capacities and of the evolution of the world nuclear reactor stock on a long term (by 2050) for the assessment to future uranium needs

The importance of speculative uranium deposits

International Nuclear Information System (INIS)

Kaiser, H.; Roth-Seefrid, H.

1980-01-01

Since current known uranium deposits (5 million t U) will either have been exhausted by the end of the century, or must be held in reserve for the thermal converter reactors which will be in operation by that time, the development of nuclear energy after the year 2000 will depend to a large extent on the early availability of speculative uranium deposits. The speculative deposits represent, by definition, the quantities of uranium which are presumed to exist in addition to the 'known' deposits and which can ultimately be exploited according to current technical-economic and ecological standpoints. When viewed critically, however, the US-DOE model used for this purpose projects an over-optimistic picture of uranium supplies and was, therefore, only accepted by the INFCE with a series of limitations and reservations. Overall the model represents a well-founded reassurance for future uranium exploration - nothing more and nothing less. The model clearly shows that due to the long lead-in times considerable expenditure will be required for uranium exploration in the coming years. It is probable that this level of investment will have to be increased several times over in the 1990s as the search moves to greater depths and to less-accessible regions. (orig./UA) [de

Internal dosimetry and radiotoxicity of long-lived uranium isotopes

International Nuclear Information System (INIS)

Jacobi, W.

1980-03-01

The dose to relevant tissues and the effective dose equivalent by ingestion and inhalation of uranium compounds are evaluated on the basis of the new metabolic and dosimetric models recommended by ICRP. Applying these dose factors annual limits for intake of these compounds by workers are derived. Finally the natural uranium exposure of the population is described. From the measured natural U-content of body tissues dose factors for the dietary intake of uranium can be estimated. (orig.) [de

Analysis of uranium urinalysis and in vivo measurement results from eleven participating uranium mills

International Nuclear Information System (INIS)

Spitz, H.B.; Simpson, J.C.; Aldridge, T.L.

1984-05-01

Uranium urinalysis and in vivo examination results obtained from workers at eleven uranium mills between 1978 and 1980 were evaluated. The main purpose was to determine the degree of the mills' compliance with bioassay monitoring recommendations given in the draft NRC Regulatory Guide 8.22 (USNRC 1978). The effect of anticipated changes in the draft regulatory guidance, as expressed to PNL in May 1982, was also studied. Statistical analyses of the data showed that the bioassay results did not reliably meet the limited performance criteria given in the draft regulatory guide. Furthermore, quality control measurements of uranium in urine indicated that detection limits at α = β = 0.05 ranged from 13 μg/l to 29 μg/l, whereas the draft regulatory guidance suggests 5 μg/l as the detection limit. Recommendations for monitoring frequencies given in the draft guide were not followed consistently from mill to mill. The results of these statistical analyses indicate a need to include performance criteria for accuracy, precision, and confidence in revisions of the draft Regulatory Guide 8.22. Revised guidance should also emphasize the need for each mill to continually test the laboratory performing urinalyses by submitting quality control samples (i.e., blank and spiked urine samples as open and blind test) to insure that the performance criteria are being met. Recommendations for a bioassay audit program are also given. 25 references, 15 figures, 17 tables

Uranium content of petroleum by fission track technique

International Nuclear Information System (INIS)

Paschoa, A.S.; Mafra, O.Y.; Oliveira, C.A.N. de; Pinto, L.R.

1981-03-01

The feasibility of the fission track registration technique to investigate the natural uranium concentration in petroleum is examined. The application of this technique to petroleum is briefly described and discussed critically. The results obtained so far indicate uranium concentrations in samples of Brazilian petroleum which are over the detect ion limit of fission track technique. (Author) [pt

Deployable nuclear fleet based on available quantities of uranium and reactor types – the case of fast reactors started up with enriched uranium

Directory of Open Access Journals (Sweden)

Baschwitz Anne

2016-01-01

Full Text Available International organizations regularly produce global energy demand scenarios. To account for the increasing population and GDP trends, as well as to encompass evolving energy uses while satisfying constraints on greenhouse gas emissions, long-term installed nuclear power capacity scenarios tend to be more ambitious, even after the Fukushima accident. Thus, the amounts of uranium or plutonium needed to deploy such capacities could be limiting factors. This study first considers light-water reactors (LWR, GEN III using enriched uranium, like most of the current reactor technologies. It then examines the contribution of future fast reactors (FR, GEN IV operating with an initial fissile load and then using depleted uranium and recycling their own plutonium. However, as plutonium is only available in limited quantity since it is only produced in nuclear reactors, the possibility of starting up these Generation IV reactors with a fissile load of enriched uranium is also explored. In one of our previous studies, the uranium consumption of a third-generation reactor like an EPR™ was compared with that of a fast reactor started up with enriched uranium (U5-FR. For a reactor lifespan of 60 years, the U5-FR consumes three times less uranium than the EPR and represents a 60% reduction in terms of separative work units (SWU, though its requirements are concentrated over the first few years of operation. The purpose of this study is to investigate the relevance of U5-FRs in a nuclear fleet deployment configuration. Considering several power demand scenarios and assuming different finite quantities of available natural uranium, this paper examines what types of reactors must be deployed to meet the demand. The deployment of light-water reactors only is not sustainable in the long run. Generation IV reactors are therefore essential. Yet when started up with plutonium, the number of reactors that can be deployed is also limited. In a fleet deployment

The determination of traces of uranium by means of laser fluorometry

International Nuclear Information System (INIS)

Venter, R.J.

1987-11-01

A method and apparatus were developed to quantitatively determine traces of uranium. A xenon chloride excimer laser was used as an excitation source, which provided various advantages above the conventional light sources. Boxcar integration was used to limit background fluorescence by time-resolved fluorescence spectroscopy. A characteristic wavelength of uranium fluorescence was selected with cut-off filters and a monochromator. The effect of different matrices on the fluorescence of uranium was determined, and the most suitable matrix for quantitative analysis was chosen. A quick and simple method for determining uranium was developed. A combined water sample of industrial effluent was used to evaluate the method. The effect of interfering species, characteristic of the water sample, was examined. A standard addition technique was used to compensate for the effect of the interfering species. The detection limit of uranium in pure water was calculated at three times the standard deviation of the blank sample and was found to be 14 pg/cm 3

Reduction of uranium hexafluoride to uranium tetrafluoride

International Nuclear Information System (INIS)

Chang, I.S.; Do, J.B.; Choi, Y.D.; Park, M.H.; Yun, H.H.; Kim, E.H.; Kim, Y.W.

1982-01-01

The single step continuous reduction of uranium hexafluoride (UF 6 ) to uranium tetrafluoride (UF 4 ) has been investigated. Heat required to initiate and maintain the reaction in the reactor is supplied by the highly exothermic reaction of hydrogen with a small amount of elemental fluorine which is added to the uranium hexafluoride stream. When gases uranium hexafluoride and hydrogen react in a vertical monel pipe reactor, the green product, UF 4 has 2.5g/cc in bulk density and is partly contaminated by incomplete reduction products (UF 5 ,U 2 F 9 ) and the corrosion product, presumably, of monel pipe of the reactor itself, but its assay (93% of UF 4 ) is acceptable for the preparation of uranium metal with magnesium metal. Remaining problems are the handling of uranium hexafluoride, which is easily clogging the flowmeter and gas feeding lines because of extreme sensitivity toward moisture, and a development of gas nozzel for free flow of uranium hexafluoride gas. (Author)

Shortage of uranium already in the 1980's: expand Ranstad at once

Energy Technology Data Exchange (ETDEWEB)

Berg, G

1975-11-14

The extraction of uranium at Ranstad must be increased and the construction of thermal nuclear power stations limited until enough breeder reactors are available. A shortage of uranium is expected for the 1980's. Deposits of uranium ore in various countries are tabulated and their yields and cost of extraction stated.

Plant-uptake of uranium: Hydroponic and soil system studies

Science.gov (United States)

Ramaswami, A.; Carr, P.; Burkhardt, M.

2001-01-01

Limited information is available on screening and selection of terrestrial plants for uptake and translocation of uranium from soil. This article evaluates the removal of uranium from water and soil by selected plants, comparing plant performance in hydroponic systems with that in two soil systems (a sandy-loam soil and an organic-rich soil). Plants selected for this study were Sunflower (Helianthus giganteus), Spring Vetch (Vicia sativa), Hairy Vetch (Vicia villosa), Juniper (Juniperus monosperma), Indian Mustard (Brassica juncea), and Bush Bean (Phaseolus nanus). Plant performance was evaluated both in terms of the percent uranium extracted from the three systems, as well as the biological absorption coefficient (BAC) that normalized uranium uptake to plant biomass. Study results indicate that uranium extraction efficiency decreased sharply across hydroponic, sandy and organic soil systems, indicating that soil organic matter sequestered uranium, rendering it largely unavailable for plant uptake. These results indicate that site-specific soils must be used to screen plants for uranium extraction capability; plant behavior in hydroponic systems does not correlate well with that in soil systems. One plant species, Juniper, exhibited consistent uranium extraction efficiencies and BACs in both sandy and organic soils, suggesting unique uranium extraction capabilities.

Precise coulometric titration of uranium in a high-purity uranium metal and in uranium compounds

International Nuclear Information System (INIS)

Tanaka, Tatsuhiko; Yoshimori, Takayoshi

1975-01-01

Uranium in uranyl nitrate, uranium trioxide and a high-purity uranium metal was assayed by the coulometric titration with biamperometric end-point detection. Uranium (VI) was reduced to uranium (IV) by solid bismuth amalgam in 5M sulfuric acid solution. The reduced uranium was reoxidized to uranium (VI) with a large excess of ferric ion at a room temperature, and the ferrous ion produced was titrated with the electrogenerated manganese(III) fluoride. In the analyses of uranium nitrate and uranium trioxide, the results were precise enough when the error from uncertainty in water content in the samples was considered. The standard sample of pure uranium metal (JAERI-U4) was assayed by the proposed method. The sample was cut into small chips of about 0.2g. Oxides on the metal surface were removed by the procedure shown by National Bureau of Standards just before weighing. The mean assay value of eleven determinations corrected for 3ppm of iron was (99.998+-0.012) % (the 95% confidence interval for the mean), with a standard deviation of 0.018%. The proposed coulometric method is simple and permits accurate and precise determination of uranium which is matrix constituent in a sample. (auth.)

31 CFR 540.317 - Uranium feed; natural uranium feed.

Science.gov (United States)

2010-07-01

... 31 Money and Finance: Treasury 3 2010-07-01 2010-07-01 false Uranium feed; natural uranium feed... (Continued) OFFICE OF FOREIGN ASSETS CONTROL, DEPARTMENT OF THE TREASURY HIGHLY ENRICHED URANIUM (HEU) AGREEMENT ASSETS CONTROL REGULATIONS General Definitions § 540.317 Uranium feed; natural uranium feed. The...

Uranium exploration

International Nuclear Information System (INIS)

De Voto, R.H.

1984-01-01

This paper is a review of the methodology and technology that are currently being used in varying degrees in uranium exploration activities worldwide. Since uranium is ubiquitous and occurs in trace amounts (0.2 to 5 ppm) in virtually all rocks of the crust of the earth, exploration for uranium is essentially the search of geologic environments in which geologic processes have produced unusual concentrations of uranium. Since the level of concentration of uranium of economic interest is dependent on the present and future price of uranium, it is appropriate here to review briefly the economic realities of uranium-fueled power generation. (author)

Uranium

International Nuclear Information System (INIS)

1982-01-01

The development, prospecting, research, processing and marketing of South Africa's uranium industry and the national policies surrounding this industry form the headlines of this work. The geology of South Africa's uranium occurences and their positions, the processes used in the extraction of South Africa's uranium and the utilisation of uranium for power production as represented by the Koeberg nuclear power station near Cape Town are included in this publication

Influence of uranium hydride oxidation on uranium metal behaviour

International Nuclear Information System (INIS)

Patel, N.; Hambley, D.; Clarke, S.A.; Simpson, K.

2013-01-01

This work addresses concerns that the rapid, exothermic oxidation of active uranium hydride in air could stimulate an exothermic reaction (burning) involving any adjacent uranium metal, so as to increase the potential hazard arising from a hydride reaction. The effect of the thermal reaction of active uranium hydride, especially in contact with uranium metal, does not increase in proportion with hydride mass, particularly when considering large quantities of hydride. Whether uranium metal continues to burn in the long term is a function of the uranium metal and its surroundings. The source of the initial heat input to the uranium, if sufficient to cause ignition, is not important. Sustained burning of uranium requires the rate of heat generation to be sufficient to offset the total rate of heat loss so as to maintain an elevated temperature. For dense uranium, this is very difficult to achieve in naturally occurring circumstances. Areas of the uranium surface can lose heat but not generate heat. Heat can be lost by conduction, through contact with other materials, and by convection and radiation, e.g. from areas where the uranium surface is covered with a layer of oxidised material, such as burned-out hydride or from fuel cladding. These rates of heat loss are highly significant in relation to the rate of heat generation by sustained oxidation of uranium in air. Finite volume modelling has been used to examine the behaviour of a magnesium-clad uranium metal fuel element within a bottle surrounded by other un-bottled fuel elements. In the event that the bottle is breached, suddenly, in air, it can be concluded that the bulk uranium metal oxidation reaction will not reach a self-sustaining level and the mass of uranium oxidised will likely to be small in relation to mass of uranium hydride oxidised. (authors)

Influence of uranium hydride oxidation on uranium metal behaviour

Energy Technology Data Exchange (ETDEWEB)

Patel, N.; Hambley, D. [National Nuclear Laboratory (United Kingdom); Clarke, S.A. [Sellafield Ltd (United Kingdom); Simpson, K.

2013-07-01

This work addresses concerns that the rapid, exothermic oxidation of active uranium hydride in air could stimulate an exothermic reaction (burning) involving any adjacent uranium metal, so as to increase the potential hazard arising from a hydride reaction. The effect of the thermal reaction of active uranium hydride, especially in contact with uranium metal, does not increase in proportion with hydride mass, particularly when considering large quantities of hydride. Whether uranium metal continues to burn in the long term is a function of the uranium metal and its surroundings. The source of the initial heat input to the uranium, if sufficient to cause ignition, is not important. Sustained burning of uranium requires the rate of heat generation to be sufficient to offset the total rate of heat loss so as to maintain an elevated temperature. For dense uranium, this is very difficult to achieve in naturally occurring circumstances. Areas of the uranium surface can lose heat but not generate heat. Heat can be lost by conduction, through contact with other materials, and by convection and radiation, e.g. from areas where the uranium surface is covered with a layer of oxidised material, such as burned-out hydride or from fuel cladding. These rates of heat loss are highly significant in relation to the rate of heat generation by sustained oxidation of uranium in air. Finite volume modelling has been used to examine the behaviour of a magnesium-clad uranium metal fuel element within a bottle surrounded by other un-bottled fuel elements. In the event that the bottle is breached, suddenly, in air, it can be concluded that the bulk uranium metal oxidation reaction will not reach a self-sustaining level and the mass of uranium oxidised will likely to be small in relation to mass of uranium hydride oxidised. (authors)

Jarosite formation in the uranium processing circuit of Denison Mines Limited, Elliot Lake, Ontario

International Nuclear Information System (INIS)

Dutrizac, J.E.

1985-04-01

Jarosite precipitation occurs in several parts of the uranium processing circuit of Denison Mines Limited, Elliot Lake, Ontario. Extensive precipitation of jarosite takes place in the filter cloth and on the drum face of the secondary drum filters, and this precipitation causes severe operating difficulties. Precipitation of jarosite is also observed in the ion exchange beads, but it is not known whether the jarosite is responsible for the observed decrease in resin efficiency. The resin beads are also rimmed with significant quantities of silica, lead, phosphate, sulphate, etc. which could be responsible for the fouling of the resin. In every instance, potassium jarosite, containing only minor amounts of sodium or ammonium, was the observed species; the potassium likely originates from the acid leaching of muscovite in the ore. Potential methods of avoiding the jarosite problem are discussed, but these may not be compatible with the overall process requirements

Uranium conversion; Urankonvertering

Energy Technology Data Exchange (ETDEWEB)

Oliver, Lena; Peterson, Jenny; Wilhelmsen, Katarina [Swedish Defence Research Agency (FOI), Stockholm (Sweden)

2006-03-15

FOI, has performed a study on uranium conversion processes that are of importance in the production of different uranium compounds in the nuclear industry. The same conversion processes are of interest both when production of nuclear fuel and production of fissile material for nuclear weapons are considered. Countries that have nuclear weapons ambitions, with the intention to produce highly enriched uranium for weapons purposes, need some degree of uranium conversion capability depending on the uranium feed material available. This report describes the processes that are needed from uranium mining and milling to the different conversion processes for converting uranium ore concentrate to uranium hexafluoride. Uranium hexafluoride is the uranium compound used in most enrichment facilities. The processes needed to produce uranium dioxide for use in nuclear fuel and the processes needed to convert different uranium compounds to uranium metal - the form of uranium that is used in a nuclear weapon - are also presented. The production of uranium ore concentrate from uranium ore is included since uranium ore concentrate is the feed material required for a uranium conversion facility. Both the chemistry and principles or the different uranium conversion processes and the equipment needed in the processes are described. Since most of the equipment that is used in a uranium conversion facility is similar to that used in conventional chemical industry, it is difficult to determine if certain equipment is considered for uranium conversion or not. However, the chemical conversion processes where UF{sub 6} and UF{sub 4} are present require equipment that is made of corrosion resistant material.

Molecular analysis of phosphate limitation in Geobacteraceae during the bioremediation of a uranium-contaminated aquifer

Energy Technology Data Exchange (ETDEWEB)

N' Guessan, L.A.; Elifantz, H.; Nevin, K.P.; Mouser, P.J.; Methe, B.; Woodard, T. L.; Manley, K.; Williams, K. H.; Wilkins, M. J.; Larsen, J.T.; Long, P. E.; Lovley, D. R.

2009-09-01

Nutrient limitation is an environmental stress that may reduce the effectiveness of bioremediation strategies, especially when the contaminants are organic compounds or when organic compounds are added to promote microbial activities such as metal reduction. Genes indicative of phosphate-limitation were identified via microarray analysis of chemostat cultures of Geobacter sulfureducens. This analysis revealed that genes in the pst-pho operon, which is associated with a high affinity phosphate uptake system in other microorganisms, had significantly higher transcript abundance under phosphate-limiting conditions, with the genes pstB and phoU the most up-regulated. Quantitative PCR analysis of pstB and phoU transcript levels in G. sulfurreducens grown in chemostats demonstrated that the expression of these genes increased when phosphate was removed from the culture medium. Transcripts of pstB and phoU within the subsurface Geobacter species predominating during an in situ uranium bioremediation field experiment were more abundant than in chemostat cultures of G. sulfurreducens that were not limited for phosphate. Addition of phosphate to incubations of subsurface sediments did not stimulate dissimilatory metal reduction. The added phosphate was rapidly adsorbed onto the sediments. The results demonstrate that Geobacter species can effectively reduce U(VI) even when experiencing suboptimal phosphate concentrations and that increasing phosphate availability with phosphate additions is difficult to achieve due to the high reactivity of this compound. This transcript-based approach developed for diagnosing phosphate limitation should be applicable to assessing the potential need for additional phosphate in other bioremediation processes.

Slightly enriched uranium fuel for a PHWR

International Nuclear Information System (INIS)

Notari, C.; Marajofsky, A.

1997-01-01

An improved fuel element design for a PHWR using slightly enriched uranium fuel is presented. It maintains the general geometric disposition of the currently used in the argentine NPP's reactors, replacing the outer ring of rods by rods containing annular pellets. Power density reduction is achieved with modest burnup losses and the void volume in the pellets can be used to balance these two opposite effects. The results show that with this new design, the fuel can be operated at higher powers without violating thermohydraulic limits and this means an improvement in fuel management flexibility, particularly in the transition from natural uranium to slightly enriched uranium cycle. (author)

Uranium speciation in Fernald soils

International Nuclear Information System (INIS)

Morris, D.E.; Conradson, S.D.; Tait, C.D.; Chisholm-Brause, C.J.; Berg, J.; Musgrave, J.

1992-01-01

This report details progress made from January 1 to May 31, 1992 in this analytical support task to determine the speciation of uranium in contaminated soil samples from the Fernald Environmental Management Project site under the auspices of the Uranium in Soils Integrated Demonstration funded through the US DOE's Office of Technology Development. The authors' efforts have focused on characterization of soil samples collected by S.Y. Lee (Oak Ridge National Laboratory) from five locales at the Fernald site. These were chosen to sample a broad range of uranium source terms. On the basis of x-ray absorption spectroscopy data, they have determined that the majority of uranium (> 80--90%) exists in the hexavalent oxidation state for all samples examined. This is a beneficial finding from the perspective of remediation, because U(VI) species are more soluble in general than uranium species in other oxidation states. Optical luminescence data from many of the samples show the characteristic structured yellow-green emission from the uranyl (UO 2 2+ ) moiety. The luminescence data also suggest that much of the uranium in these soils is present as well-crystallized UO 2 2+ species. Some clear spectroscopic distinctions have been noted for several samples that illustrate significant differences in the speciation (1) from site to site, (2) within different horizons at the same site, and (3) within different size fractions of the soils in the same horizon at the same site. This marked heterogeneity in uranyl speciation suggests that several soil washing strategies may be necessary to reduce the total uranium concentrations within these soils to regulatory limits

Internal contamination by natural uranium: monitoring by analysis of urine of individuals exposed by occupational inhalation

International Nuclear Information System (INIS)

Ramalho, A.T.

1982-01-01

Urine samples from men working at Usina Santo Amaro (USAM - State of Sao Paulo), a monazite refinery, were analysed for uranium concentration, using fluorometric analysis and alpha spectrometry. All samples analysed presented uranium concentration below the lower limit of detection. Theoretical values were calculated for uranium concentration in urine samples from workers at the annual limit of intake (ALI) for inhalation of natural uranium, recommended in Publication 30 of the International Commission on Radiological Protection (ICRP, 1979). The two different methods used for analysis of natural uranium concentration in the urine samples were compared: fluorimetry and alpha spectrometry. (author)

Trace content of uranium in spices and condiments

Energy Technology Data Exchange (ETDEWEB)

Sharma, Y P; Lal, N; Mahesh, K; Nagpaul, K K [Regional Engineering Coll., Kurukshetra (India). Dept. of Physics; Chakarvarti, S K [Kurukshetra Univ. (India). Dept. of Physics

1981-10-01

The natural uranium trace contents of eighteen spice and condiment samples belonging to twelve different plant families in India were determined by the fission track etch technique. The uranium contents varied from 0.28 +- 0.002 to 78.6 +- 0.50 pg/g. This does not pose a serious health hazard since the permissible limit intake by humans is 40 mg/day.

Uranium concentrations in groundwater, northeastern Washington

Science.gov (United States)

Kahle, Sue C.; Welch, Wendy B.; Tecca, Alison E.; Eliason, Devin M.

2018-04-18

A study of uranium in groundwater in northeastern Washington was conducted to make a preliminary assessment of naturally occurring uranium in groundwater relying on existing information and limited reconnaissance sampling. Naturally occurring uranium is associated with granitic and metasedimentary rocks, as well as younger sedimentary deposits, that occur in this region. The occurrence and distribution of uranium in groundwater is poorly understood. U.S. Environmental Protection Agency (EPA) regulates uranium in Group A community water systems at a maximum contaminant level (MCL) of 30 μg/L in order to reduce uranium exposure, protect from toxic kidney effects of uranium, and reduce the risk of cancer. However, most existing private wells in the study area, generally for single family use, have not been sampled for uranium. This document presents available uranium concentration data from throughout a multi-county region, identifies data gaps, and suggests further study aimed at understanding the occurrence of uranium in groundwater.The study encompasses about 13,000 square miles (mi2) in the northeastern part of Washington with a 2010 population of about 563,000. Other than the City of Spokane, most of the study area is rural with small towns interspersed throughout the region. The study area also includes three Indian Reservations with small towns and scattered population. The area has a history of uranium exploration and mining, with two inactive uranium mines on the Spokane Indian Reservation and one smaller inactive mine on the outskirts of Spokane. Historical (1977–2016) uranium in groundwater concentration data were used to describe and illustrate the general occurrence and distribution of uranium in groundwater, as well as to identify data deficiencies. Uranium concentrations were detected at greater than 1 microgram per liter (μg/L) in 60 percent of the 2,382 historical samples (from wells and springs). Uranium concentrations ranged from less than 1 to

Uranium

International Nuclear Information System (INIS)

Mackay, G.A.

1978-01-01

The author discusses the contribution made by various energy sources in the production of electricity. Estimates are made of the future nuclear contribution, the future demand for uranium and future sales of Australian uranium. Nuclear power growth in the United States, Japan and Western Europe is discussed. The present status of the six major Australian uranium deposits (Ranger, Jabiluka, Nabarlek, Koongarra, Yeelerrie and Beverley) is given. Australian legislation relevant to the uranium mining industry is also outlined

Development of a chronocoulometric method for uranium traces determination with basis on nitrate catalytic reduction

International Nuclear Information System (INIS)

Cantagallo, M.I.C.; Gutz, I.G.R.

1990-01-01

The application of chronocoulometric technique with catalytic reduction of uranium/nitrate with catalytic reduction of uranium/nitrate system is described to give a detection limits on the sub-nanomolar region of uranium. (author)

Czechoslovak uranium

International Nuclear Information System (INIS)

Pluskal, O.

1992-01-01

Data and knowledge related to the prospecting, mining, processing and export of uranium ores in Czechoslovakia are presented. In the years between 1945 and January 1, 1991, 98,461.1 t of uranium were extracted. In the period 1965-1990 the uranium industry was subsidized from the state budget to a total of 38.5 billion CSK. The subsidies were put into extraction, investments and geologic prospecting; the latter was at first, ie. till 1960 financed by the former USSR, later on the two parties shared costs on a 1:1 basis. Since 1981 the prospecting has been entirely financed from the Czechoslovak state budget. On Czechoslovak territory uranium has been extracted from deposits which may be classified as vein-type deposits, deposits in uranium-bearing sandstones and deposits connected with weathering processes. The future of mining, however, is almost exclusively being connected with deposits in uranium-bearing sandstones. A brief description and characteristic is given of all uranium deposits on Czechoslovak territory, and the organization of uranium mining in Czechoslovakia is described as is the approach used in the world to evaluate uranium deposits; uranium prices and actual resources are also given. (Z.S.) 3 figs

Uranium in Niger; L'uranium au Niger

Energy Technology Data Exchange (ETDEWEB)

Gabelmann, E

1978-03-15

This document presents government policy in the enhancement of uranium resources, existing mining companies and their productions, exploitation projects and economical outcome related to the uranium mining and auxiliary activities. [French] Le document presente la politique de l'Etat dans le cadre de la mise en valeur des ressources d'uranium, les societes minieres existantes et leurs productions, les projets d'exploitation d'uranium et les retombees economiques liees aux activites uraniferes et connexes.

Standard specification for uranium hexafluoride enriched to less than 5 % 235U

CERN Document Server

American Society for Testing and Materials. Philadelphia

2010-01-01

1.1 This specification covers nuclear grade uranium hexafluoride (UF6) that either has been processed through an enrichment plant, or has been produced by the blending of Highly Enriched Uranium with other uranium to obtain uranium of any 235U concentration below 5 % and that is intended for fuel fabrication. The objectives of this specification are twofold: (1) To define the impurity and uranium isotope limits for Enriched Commercial Grade UF6 so that, with respect to fuel design and manufacture, it is essentially equivalent to enriched uranium made from natural UF6; and (2) To define limits for Enriched Reprocessed UF6 to be expected if Reprocessed UF6 is to be enriched without dilution with Commercial Natural UF6. For such UF6, special provisions, not defined herein, may be needed to ensure fuel performance and to protect the work force, process equipment, and the environment. 1.2 This specification is intended to provide the nuclear industry with a standard for enriched UF6 that is to be used in the pro...

Uranium ores

International Nuclear Information System (INIS)

Poty, B.; Roux, J.

1998-01-01

The processing of uranium ores for uranium extraction and concentration is not much different than the processing of other metallic ores. However, thanks to its radioactive property, the prospecting of uranium ores can be performed using geophysical methods. Surface and sub-surface detection methods are a combination of radioactive measurement methods (radium, radon etc..) and classical mining and petroleum prospecting methods. Worldwide uranium prospecting has been more or less active during the last 50 years, but the rise of raw material and energy prices between 1970 and 1980 has incited several countries to develop their nuclear industry in order to diversify their resources and improve their energy independence. The result is a considerable increase of nuclear fuels demand between 1980 and 1990. This paper describes successively: the uranium prospecting methods (direct, indirect and methodology), the uranium deposits (economical definition, uranium ores, and deposits), the exploitation of uranium ores (use of radioactivity, radioprotection, effluents), the worldwide uranium resources (definition of the different categories and present day state of worldwide resources). (J.S.)

URANIUM MARKET TRENDS

Directory of Open Access Journals (Sweden)

Serghei MĂRGULESCU

2016-06-01

Full Text Available The recent UN Climate Talks in Paris have put forward the goal of limiting the global temperature rise to two degrees Celsius by the end of the century. This is providing a strong political base for expanding the nuclear power capacity because of the critical role that nuclear power plants play in the production of electricity without emissions of greenhouse gases. In all, more than a dozen countries get over 25% of their energy from nuclear power, with 437 nuclear reactors operating around the world. On top of that, there are another 71 reactors under construction, 165 planned, and 315 proposed. Global uranium demand is expected to rise 40% by 2025 and 81% by 2035. Mined supply of uranium will struggle to keep pace amid rising demand and falling secondary supplies. A cumulative supply deficit is expected to emerge by 2021 while 2016 marks a huge inflection point for the industry, beeing the first year that demand will actually exceed supplies, creating a 60,000-tonne shortfall by 2018. Over the next 10 years, we're going to see uranium prices more than double while the bull run will begin in earnest in 2016.

Simulation of uranium oxides reduction kinetics by hydrogen. Reactivities of germination and growth

International Nuclear Information System (INIS)

Brun, C.

1997-01-01

The aim of this work is to simulate the reduction by hydrogen of the tri-uranium octo-oxide U 3 O 8 (obtained by uranium trioxide calcination) into uranium dioxide. The kinetics curves have been obtained by thermal gravimetric analysis, the hydrogen and steam pressures being defined. The geometrical modeling which has allowed to explain the trend of the kinetics curves and of the velocity curves is an anisotropic germination-growth modeling. The powder is supposed to be formed of spherical grains with the same radius. The germs of the new UO 2 phase appear at the surface of the U 3 O 8 grains with a specific germination frequency. The growth reactivity is anisotropic and is very large in the tangential direction to the grains surface. Then, the uranium dioxide growths inside the grain and the limiting step is the grain surface. The variations of the growth reactivity and of the germination specific frequency in terms of the gases partial pressures and of the temperature have been explained by two different mechanisms. The limiting step of the growth mechanism is the desorption of water in the uranium dioxide surface. Concerning the germination mechanism the limiting step is a water desorption too but in the tri-uranium octo-oxide surface. The same geometrical modeling and the same germination and growth mechanisms have been applied to the reduction of a tri-uranium octo-oxide obtained by calcination of hydrated uranium trioxide. The values of the germination specific frequency of this solid are nevertheless weaker than those of the solid obtained by direct calcination of the uranium trioxide. (O.M.)

Fabrication procedures for manufacturing high uranium concentration dispersion fuel elements

International Nuclear Information System (INIS)

Souza, J.A.B.; Durazzo, M.

2010-01-01

IPEN developed and made available for routine production the technology for manufacturing dispersion type fuel elements for use in research reactors. However, the fuel produced at IPEN is limited to the uranium concentration of 3.0 gU/cm 3 by using the U 3 Si 2 -Al dispersion. Increasing the uranium concentration of the fuel is interesting by the possibility of increasing the reactor core reactivity and lifetime of the fuel. It is possible to increase the concentration of uranium in the fuel up to the technological limit of 4.8 gU/cm 3 for the U 3 Si 2 -Al dispersion, which is well placed around the world. This new fuel will be applicable in the new Brazilian-Multipurpose Reactor RMB. This study aimed to develop the manufacturing process of high uranium concentration fuel, redefining the procedures currently used in the manufacture of IPEN. This paper describes the main procedures adjustments that will be necessary. (author)

Fabrication procedures for manufacturing high uranium concentration dispersion fuel elements

Energy Technology Data Exchange (ETDEWEB)

Souza, Jose Antonio Batista de; Durazzo, Michelangelo, E-mail: jasouza@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2011-07-01

IPEN developed and made available for routine production the technology for manufacturing dispersion type fuel elements for use in research reactors. However, the fuel produced at IPEN is limited to the uranium concentration of 3.0 g U/c m3 by using the U{sub 3}Si{sub 2}-Al dispersion. Increasing the uranium concentration of the fuel is interesting by the possibility of increasing the reactor core reactivity and lifetime of the fuel. It is possible to increase the concentration of uranium in the fuel up to the technological limit of 4.8 g U/c m3 for the U{sub 3}Si{sub 2}-Al dispersion, which is well placed around the world. This new fuel will be applicable in the new Brazilian- Multipurpose Reactor RMB. This study aimed to develop the manufacturing process of high uranium concentration fuel, redefining the procedures currently used in the manufacture of IPEN. This paper describes the main procedures adjustments that will be necessary. (author)

Why the search for uranium should continue; Pourquoi continuer a chercher de l'uranium

Energy Technology Data Exchange (ETDEWEB)

Mabile, J; Gangloff, A [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

1964-07-01

At the 1958 Geneva conference a report was given of the hopes placed in French uranium resources, and the work in hand on projects for mines and mills. Even though the French ground continued to confirm its promises, production has been limited because of the risk of massive over-production. Moreover worldwide production surpluses remove any immediate worries about supplies. However, the French uranium potential, at the rate of exploitation which can be reasonably foreseen, seems to be limited, promising only a few decades of production. This situation is more serious still for Europe as a whole, at the very time when the rapid expansion of atomic energy is beginning. On a world wide basis it may be anticipated that after the closing down of mines, an equilibrium between production and requirements will be reached in ten years, the Increase in production being then easily achieved by the reopening of temporarily closed mines. However, by 1980 the requirements will exceed the maximum production capacity laid down in 1960-1961. Finally, towards the end of the century, there will be a discrepancy between the uranium reserves, then necessary, and those which have been. discovered so far in the world, at the cost of the considerable efforts made during the years 1948-1958. No time should be lost in an effort to discover new resources: either in countries not yet prospected, or by the use of more sensitive methods. Failing this, the uranium market, badly shaken by present over-production, will suffer new crises unless the mining industry is well prepared in advance for a rapid exponential expansion after 1975-1980. (author) [French] Lors de la Conference de Geneve 1958, avaient ete exposes les espoirs mis dans les ressources francaises en Uranium, et les realisations des mines et usines en cours. Les risques de surproduction massive ont conduit a limiter les productions, cependant que le sous-sol francais confirmait ses promesses. Par ailleurs les excedents mondiaux de

Evaluation of neutralization treatment processes and their use for uranium tailings solutions

International Nuclear Information System (INIS)

Sherwood, D.R.; Opitz, B.E.; Serne, R.J.

1985-01-01

The potential for groundwater contamination from the typically acidic mill wastes that are disposed of in tailings impoundments is of primary concern at uranium mill sites in the US. Solution-treatment processes provide a system for limiting the environmental impact from acidic seepage. Treatment of uranium tailings solutions from evaporation ponds, underdrains, and surface seeps could aid in decommissioning active sites or be used as an emergency measure to avert possible uncontrolled discharges. At present, neutralization processes appear to be best suited for treating uranium mill tailings solution because they can, at a reasonable cost, limit the solution concentration of many contaminants and thus reduce the potential for groundwater contamination. However, the effectiveness of the neutralization process depends on the reagent used as well as the chemistry of the waste stream. This article provides a description of neutralization processes, an assessment of their performance on acidic uranium tailings leachates, and recommendations for their use at US uranium mill sites

Single-molecule magnetism in a single-ion triamidoamine uranium(V) terminal mono-oxo complex

International Nuclear Information System (INIS)

King, David M.; McMaster, Jonathan; Lewis, William; Blake, Alexander J.; Liddle, Stephen T.; Tuna, Floriana; McInnes, Eric J.L.

2013-01-01

Straightforward oxidation of a triamidoamine uranium(III) complex with trimethyl-N-oxide affords a uranium(V) terminal mono-oxo complex which is the first clear-cut example of a uranium(V) single-molecule magnet (SMM). This monometallic complex unambiguously shows that a strongly axially ligated and thus anisotropic ligand field can be used to overcome the limited magnetic anisotropy of uranium(V). [de

Radiometric sorting of Rio Algom uranium ore

International Nuclear Information System (INIS)

Cristovici, M.A.

1983-11-01

An ore sample of about 0.2 percent uranium from Quirke Mine was subjected to radiometric sorting by Ore Sorters Limited. Approximately 60 percent of the sample weight fell within the sortable size range: -150 + 25 mm. Rejects of low uranium content ( 2 (2 counts/in 2 ) but only 7.6 percent of the ore, by weight, was discarded. At 0.8-0.9 counts/cm 2 (5-6 counts/in 2 ) a significant amount of rejects was removed (> 25 percent) but the uranium loss was unacceptably high (7.7 percent). Continuation of the testwork to improve the results is proposed by trying to extend the sortable size range and to reduce the amount of fines during crushing

Uranium in South Africa: 1985

International Nuclear Information System (INIS)

1986-03-01

South Africa's participation in the nuclear industry was limited to the production of uranium and research, with minor commercial activities. The commissioning of the Koeberg Nuclear power station in 1984 placed South Africa firmly on the path of commercial nuclear power generation. A unique, locally developed uranium enrichment process will enable South Africa to be self-sufficient in its nuclear-fuel needs. Uranium has always been of secondary importance to gold as a target commodity in the exploration of the quartz-pebble conglomerates. In the Witwatersrand Basin it is estimated that in excess of R100 million was spent on exploration during 1985. This was spent primarily in the search for gold but as many of the gold reefs are uraniferous, new uranium resources are being discovered concurrently with those of gold. Uranium mineralization is present in rocks which encompass almost the whole of the geological history of South Africa. Significant mineralization is restricted to five fairly well-defined time periods. Each period is characterized by a distinct type or combination of types of mineralization. Resource estimates are divided into separate categories that reflect different levels of confidence in the quantities reported. The resource categories are further separated into levels of exploitability based on the estimated cost of their exploitation. A major part (87%) of South Africa's uranium resources is present as a by-product of gold in the quartz-pebble conglomerates of the Witwatersrand Basin. The uranium resources in the reasonably assured resources (RAR) and estimated additional resources - category I (EAR-I) catogories were 483 300 t U. Production during 1985 was 4880 t U. Although a production peaking at over 1200 t U/a is theoretically attainable, it is considered, from market projections, that a production ceilling of 10 000 t U/a would be more realistic

Uranium in South Africa: 1987

International Nuclear Information System (INIS)

1988-06-01

South Africa's participation in the nuclear industry was limited to the production of uranium and research, with minor commercial activities. The commissioning of the Koeberg Nuclear power station in 1984 placed South Africa firmly on the path of commercial nuclear power generation. A unique locally developed uranium enrichment process wil enable South Africa to be self-sufficient in its nuclear-fuel needs. Uranium has always been of secondary importance to gold as a target commodity in the exploration of the quartz-pebble conglomerates. In the Witwatersrand Basin it is estimated that in excess of R300 million was spend on exploration during 1987. This was spend primarily in the search for gold but as many of the gold reefs are uraniferous, new uranium resources are being discovered concurrently with those of gold. Uranium mineralization is present in rocks which encompass almost the whole of the geological history of South Africa. Significant mineralization is restricted to five fairly well-defined time periods. Each period is characterized by a distinct type or combination of types of mineralization. Resource estimates are divided into separate categories that reflect different levels of confidence in the quantities reported. The resource categories are further separated into levels of exploitability based on the estimated cost of their exploitation. A major part (87%) of South Africa's uranium resources is present as a by-product of gold in the quartz-pebble conglomerates of the Witwatersrand Basin. The uranium resources in the RAR and EAR-I categories were 536 500 t u. Production during 1987 was 3963 t u. Although a production peaking at over 1100 t U/a is theoretically attainable, it is considered, from market projections, that a production ceiling of 10 000 t U/a would be more realistic

The issue of separation of uranium from drinking water in the Czech Republic

International Nuclear Information System (INIS)

Krmela, Jan

2013-01-01

Natural ground water used for the preparation of drinking water contains a number of cations, anions, elements and other substances depending on the bedrock composition (Ca, Mg, Fe, Mn, heavy metals, radioactive elements, arsenic, chromium, carbonates, sulfates, phosphates, silicates, fulvic and humic acids etc.). Information about composition of drinking water is important to comply with all the requirements on sanitary of drinking water. The elements that affect the quality of drinking water mainly from groundwater, also includes radioactive elements contained in bedrock sections where water is extracted. These are the elements with long half-lives, mainly alpha emitters (U, Ra, Rn, Th, and elements of the decay series). Uranium and its decay products are found in all environmental compartments. Radionuclides come to the environment both naturally - weathering and leaching of the rocks, and as a consequence of human activities in connection with the use of raw materials. Uranium occurs naturally in four oxidation states. The most mobility has hexa-valent state (uranyl ion). Uranyl is highly soluble form of uranium in water. Mobility of uranium in soil and water is affected by many factors. Complex processes in soil and rock lead to redox reactions forming both insoluble compounds (lower valence forms of uranium) and soluble form of U (VI) (forming by reoxidation), which is again leachable into groundwater. The content of uranium in groundwater depends on the geological composition of the ground, and can reach up to hundreds of μg/L. At present the issue associated with removing uranium from drinking water is solved in the Czech Republic. New limit for the concentration of natural uranium ( 234 U, 235 U and 238 U) was recommended at a level of 15 μg/L as the highest limit based on the World Health Organization (WHO). Advice of the Chief Health Officer of the Czech Republic came into force on 1st January 2010, which decreased the limit for uranium in drinking

Pengaruh Kandungan Uranium Dalam Umpan Terhadap Efisiensi Pengendapan Uranium

OpenAIRE

Torowati

2010-01-01

PENGARUH KANDUNGAN URANIUM DALAM UMPAN TERHADAP EFISIENSI PENGENDAPAN URANIUM. Setiap aktivitas analisis di Laboratorium Kendali Kualitas, Bidang Bahan Bakar Nuklir selalu dihasilkan limbah radioaktif cair. Limbah radioaktif cair di laboratorium masih mengandung uranium yang cukup besar ± 0,600 g U/l dengan keasamaan yang cukup besar pula. Karena uranium mempunyai nilai ekonomis yang cukup tinggi maka perlu USAha untuk mengambil kembali uranium tersebut. Pada kegiatan ini telah dilak...

Uranium-series constraints on radionuclide transport and groundwater flow at the Nopal I uranium deposit, Sierra Pena Blanca, Mexico.

Science.gov (United States)

Goldstein, Steven J; Abdel-Fattah, Amr I; Murrell, Michael T; Dobson, Patrick F; Norman, Deborah E; Amato, Ronald S; Nunn, Andrew J

2010-03-01

Uranium-series data for groundwater samples from the Nopal I uranium ore deposit were obtained to place constraints on radionuclide transport and hydrologic processes for a nuclear waste repository located in fractured, unsaturated volcanic tuff. Decreasing uranium concentrations for wells drilled in 2003 are consistent with a simple physical mixing model that indicates that groundwater velocities are low ( approximately 10 m/y). Uranium isotopic constraints, well productivities, and radon systematics also suggest limited groundwater mixing and slow flow in the saturated zone. Uranium isotopic systematics for seepage water collected in the mine adit show a spatial dependence which is consistent with longer water-rock interaction times and higher uranium dissolution inputs at the front adit where the deposit is located. Uranium-series disequilibria measurements for mostly unsaturated zone samples indicate that (230)Th/(238)U activity ratios range from 0.005 to 0.48 and (226)Ra/(238)U activity ratios range from 0.006 to 113. (239)Pu/(238)U mass ratios for the saturated zone are 1000 times lower than the U mobility. Saturated zone mobility decreases in the order (238)U approximately (226)Ra > (230)Th approximately (239)Pu. Radium and thorium appear to have higher mobility in the unsaturated zone based on U-series data from fractures and seepage water near the deposit.

Uranium-series constraints on radionuclide transport and groundwater flow at the Nopal I uranium deposit, Sierra Pena Blanca, Mexico

International Nuclear Information System (INIS)

Goldstein, S.J.; Abdel-Fattah, A.I.; Murrell, M.T.; Dobson, P.F.; Norman, D.E.; Amato, R.S.; Nunn, A.J.

2009-01-01

Uranium-series data for groundwater samples from the Nopal I uranium ore deposit were obtained to place constraints on radionuclide transport and hydrologic processes for a nuclear waste repository located in fractured, unsaturated volcanic tuff. Decreasing uranium concentrations for wells drilled in 2003 are consistent with a simple physical mixing model that indicates that groundwater velocities are low (∼10 m/y). Uranium isotopic constraints, well productivities, and radon systematics also suggest limited groundwater mixing and slow flow in the saturated zone. Uranium isotopic systematics for seepage water collected in the mine adit show a spatial dependence which is consistent with longer water-rock interaction times and higher uranium dissolution inputs at the front adit where the deposit is located. Uranium-series disequilibria measurements for mostly unsaturated zone samples indicate that 230 Th/ 238 U activity ratios range from 0.005-0.48 and 226 Ra/ 238 U activity ratios range from 0.006-113. 239 Pu/ 238 U mass ratios for the saturated zone are -14 , and Pu mobility in the saturated zone is >1000 times lower than the U mobility. Saturated zone mobility decreases in the order 238 U∼ 226 Ra > 230 Th∼ 239 Pu. Radium and thorium appear to have higher mobility in the unsaturated zone based on U-series data from fractures and seepage water near the deposit.

Kinetic analysis of pulsed laser induced phosphorescence for uranium determination

International Nuclear Information System (INIS)

Serdeiro, Nelida H.

2003-01-01

The laser induced kinetic phosphorescence allows the uranium determination in different kind of matrices, with a lower detection limit than those reached by other spectroscopic methods. It involves the uranyl ions excitation by a pulsed dye-laser source, followed by temporal resolution of the phosphorescence. This method is used for the determination of trace quantities of uranium in aqueous solution, with a suitable complexant agent, without chemical separation before the analysis. The objective of this paper is to present the results of uranium determinations in different standard samples, water, soil, filter and urine, and a comparison with other methods such as fluorimetry, alpha spectrometry and mass spectrometry. Moreover, the measurement conditions, the advantages and disadvantages, the sample preparation, the interferences and the detection limit are described. (author)

Uranium enrichment

International Nuclear Information System (INIS)

1991-08-01

This paper reports that in 1990 the Department of Energy began a two-year project to illustrate the technical and economic feasibility of a new uranium enrichment technology-the atomic vapor laser isotope separation (AVLIS) process. GAO believes that completing the AVLIS demonstration project will provide valuable information about the technical viability and cost of building an AVLIS plant and will keep future plant construction options open. However, Congress should be aware that DOE still needs to adequately demonstrate AVLIS with full-scale equipment and develop convincing cost projects. Program activities, such as the plant-licensing process, that must be completed before a plant is built, could take many years. Further, an updated and expanded uranium enrichment analysis will be needed before any decision is made about building an AVLIS plant. GAO, which has long supported legislation that would restructure DOE's uranium enrichment program as a government corporation, encourages DOE's goal of transferring AVLIS to the corporation. This could reduce the government's financial risk and help ensure that the decision to build an AVLIS plant is based on commercial concerns. DOE, however, has no alternative plans should the government corporation not be formed. Further, by curtailing a planned public access program, which would have given private firms an opportunity to learn about the technology during the demonstration project, DOE may limit its ability to transfer AVLIS to the private sector

Fission-track studies of uranium distribution in geological samples

International Nuclear Information System (INIS)

Brynard, H.J.

1983-01-01

The standard method of studying uranium distribution in geological material by registration of fission tracks from the thermal neutron-induced fission of 235 U has been adapted for utilisation in the SAFARI-1 reactor at Pelindaba. The theory of fission-track registration as well as practical problems are discussed. The method has been applied to study uranium distribution in a variety of rock types and the results are discussed in this paper. The method is very sensitive and uranium present in quantities far below the detection limit of the microprobe have been detected

Glances on uranium. From uranium in the earth to electric power

International Nuclear Information System (INIS)

Valsardieu, C.

1995-01-01

This book is a technical, scientific and historical analysis of the nuclear fuel cycle from the origin of uranium in the earth and the exploitation of uranium ores to the ultimate storage of radioactive wastes. It comprises 6 chapters dealing with: 1) the different steps of uranium history (discovery, history of uranium chemistry, the radium era, the physicists and the structure of matter, the military uses, the nuclear power, the uranium industry and economics), 2) the uranium in nature (nuclear structure, physical-chemical properties, radioactivity, ores, resources, cycle, deposits), 3) the sidelights on uranium history (mining, prospecting, experience, ore processing, resources, reserves, costs), 4) the uranium in the fuel cycle, energy source and industrial product (fuel cycle, fission, refining, enrichment, fuel processing and reprocessing, nuclear reactors, wastes management), 5) the other energies in competition and the uranium market (other uranium uses, fossil fuels and renewable energies, uranium market), and 6) the future of uranium (forecasting, ecology, economics). (J.S.)

Technical Basis for Assessing Uranium Bioremediation Performance

International Nuclear Information System (INIS)

PE Long; SB Yabusaki; PD Meyer; CJ Murray; AL N'Guessan

2008-01-01

In situ bioremediation of uranium holds significant promise for effective stabilization of U(VI) from groundwater at reduced cost compared to conventional pump and treat. This promise is unlikely to be realized unless researchers and practitioners successfully predict and demonstrate the long-term effectiveness of uranium bioremediation protocols. Field research to date has focused on both proof of principle and a mechanistic level of understanding. Current practice typically involves an engineering approach using proprietary amendments that focuses mainly on monitoring U(VI) concentration for a limited time period. Given the complexity of uranium biogeochemistry and uranium secondary minerals, and the lack of documented case studies, a systematic monitoring approach using multiple performance indicators is needed. This document provides an overview of uranium bioremediation, summarizes design considerations, and identifies and prioritizes field performance indicators for the application of uranium bioremediation. The performance indicators provided as part of this document are based on current biogeochemical understanding of uranium and will enable practitioners to monitor the performance of their system and make a strong case to clients, regulators, and the public that the future performance of the system can be assured and changes in performance addressed as needed. The performance indicators established by this document and the information gained by using these indicators do add to the cost of uranium bioremediation. However, they are vital to the long-term success of the application of uranium bioremediation and provide a significant assurance that regulatory goals will be met. The document also emphasizes the need for systematic development of key information from bench scale tests and pilot scales tests prior to full-scale implementation

Technical Basis for Assessing Uranium Bioremediation Performance

Energy Technology Data Exchange (ETDEWEB)

PE Long; SB Yabusaki; PD Meyer; CJ Murray; AL N’Guessan

2008-04-01

In situ bioremediation of uranium holds significant promise for effective stabilization of U(VI) from groundwater at reduced cost compared to conventional pump and treat. This promise is unlikely to be realized unless researchers and practitioners successfully predict and demonstrate the long-term effectiveness of uranium bioremediation protocols. Field research to date has focused on both proof of principle and a mechanistic level of understanding. Current practice typically involves an engineering approach using proprietary amendments that focuses mainly on monitoring U(VI) concentration for a limited time period. Given the complexity of uranium biogeochemistry and uranium secondary minerals, and the lack of documented case studies, a systematic monitoring approach using multiple performance indicators is needed. This document provides an overview of uranium bioremediation, summarizes design considerations, and identifies and prioritizes field performance indicators for the application of uranium bioremediation. The performance indicators provided as part of this document are based on current biogeochemical understanding of uranium and will enable practitioners to monitor the performance of their system and make a strong case to clients, regulators, and the public that the future performance of the system can be assured and changes in performance addressed as needed. The performance indicators established by this document and the information gained by using these indicators do add to the cost of uranium bioremediation. However, they are vital to the long-term success of the application of uranium bioremediation and provide a significant assurance that regulatory goals will be met. The document also emphasizes the need for systematic development of key information from bench scale tests and pilot scales tests prior to full-scale implementation.

Uranium prospecting; La prospection de l'uranium

Energy Technology Data Exchange (ETDEWEB)

Roubault, M [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1955-07-01

This report is an instruction book for uranium prospecting. It appeals to private prospecting. As prospecting is now a scientific and technical research, it cannot be done without preliminary studies. First of all, general prospecting methods are given with a recall of fundamental geologic data and some general principles which are common with all type of prospecting. The peculiarities of uranium prospecting are also presented and in particular the radioactivity property of uranium as well as the special aspect of uranium ores and the aspect of neighbouring ores. In a third part, a description of the different uranium ores is given and separated in two different categories: primary and secondary ores, according to the place of transformation, deep or near the crust surface respectively. In the first category, the primary ores include pitchblende, thorianite and rare uranium oxides as euxenite and fergusonite for example. In the second category, the secondary ores contain autunite and chalcolite for example. An exhaustive presentation of the geiger-Mueller counter is given with the presentation of its different components, its functioning and utilization and its maintenance. The radioactivity interpretation method is showed as well as the elaboration of a topographic map of the measured radioactivity. A brief presentation of other detection methods than geiger-Mueller counters is given: the measurement of fluorescence and a chemical test using the fluorescence properties of uranium salts. Finally, the main characteristics of uranium deposits are discussed. (M.P.)

Simulation of uranium oxides reduction kinetics by hydrogen. Reactivities of germination and growth; Modelisation de la cinetique de reduction d`oxydes d`uranium par l`hydrogene. Reactivites de germination et de croissance

Energy Technology Data Exchange (ETDEWEB)

Brun, C

1997-12-04

The aim of this work is to simulate the reduction by hydrogen of the tri-uranium octo-oxide U{sub 3}O{sub 8} (obtained by uranium trioxide calcination) into uranium dioxide. The kinetics curves have been obtained by thermal gravimetric analysis, the hydrogen and steam pressures being defined. The geometrical modeling which has allowed to explain the trend of the kinetics curves and of the velocity curves is an anisotropic germination-growth modeling. The powder is supposed to be formed of spherical grains with the same radius. The germs of the new UO{sub 2} phase appear at the surface of the U{sub 3}O{sub 8} grains with a specific germination frequency. The growth reactivity is anisotropic and is very large in the tangential direction to the grains surface. Then, the uranium dioxide growths inside the grain and the limiting step is the grain surface. The variations of the growth reactivity and of the germination specific frequency in terms of the gases partial pressures and of the temperature have been explained by two different mechanisms. The limiting step of the growth mechanism is the desorption of water in the uranium dioxide surface. Concerning the germination mechanism the limiting step is a water desorption too but in the tri-uranium octo-oxide surface. The same geometrical modeling and the same germination and growth mechanisms have been applied to the reduction of a tri-uranium octo-oxide obtained by calcination of hydrated uranium trioxide. The values of the germination specific frequency of this solid are nevertheless weaker than those of the solid obtained by direct calcination of the uranium trioxide. (O.M.) 45 refs.

Uranium

International Nuclear Information System (INIS)

Stewart, E.D.J.

1974-01-01

A discussion is given of uranium as an energy source in The Australian economy. Figures and predictions are presented on the world supply-demand position and also figures are given on the added value that can be achieved by the processing of uranium. Conclusions are drawn about Australia's future policy with regard to uranium (R.L.)

Uranium, depleted uranium, biological effects

International Nuclear Information System (INIS)

2001-01-01

Physicists, chemists and biologists at the CEA are developing scientific programs on the properties and uses of ionizing radiation. Since the CEA was created in 1945, a great deal of research has been carried out on the properties of natural, enriched and depleted uranium in cooperation with university laboratories and CNRS. There is a great deal of available data about uranium; thousands of analyses have been published in international reviews over more than 40 years. This presentation on uranium is a very brief summary of all these studies. (author)

Solubility measurement of uranium in uranium-contaminated soils

International Nuclear Information System (INIS)

Lee, S.Y.; Elless, M.; Hoffman, F.

1993-08-01

A short-term equilibration study involving two uranium-contaminated soils at the Fernald site was conducted as part of the In Situ Remediation Integrated Program. The goal of this study is to predict the behavior of uranium during on-site remediation of these soils. Geochemical modeling was performed on the aqueous species dissolved from these soils following the equilibration study to predict the on-site uranium leaching and transport processes. The soluble levels of total uranium, calcium, magnesium, and carbonate increased continually for the first four weeks. After the first four weeks, these components either reached a steady-state equilibrium or continued linearity throughout the study. Aluminum, potassium, and iron, reached a steady-state concentration within three days. Silica levels approximated the predicted solubility of quartz throughout the study. A much higher level of dissolved uranium was observed in the soil contaminated from spillage of uranium-laden solvents and process effluents than in the soil contaminated from settling of airborne uranium particles ejected from the nearby incinerator. The high levels observed for soluble calcium, magnesium, and bicarbonate are probably the result of magnesium and/or calcium carbonate minerals dissolving in these soils. Geochemical modeling confirms that the uranyl-carbonate complexes are the most stable and dominant in these solutions. The use of carbonate minerals on these soils for erosion control and road construction activities contributes to the leaching of uranium from contaminated soil particles. Dissolved carbonates promote uranium solubility, forming highly mobile anionic species. Mobile uranium species are contaminating the groundwater underlying these soils. The development of a site-specific remediation technology is urgently needed for the FEMP site

Uranium complex recycling method of purifying uranium liquors

International Nuclear Information System (INIS)

Elikan, L.; Lyon, W.L.; Sundar, P.S.

1976-01-01

Uranium is separated from contaminating cations in an aqueous liquor containing uranyl ions. The liquor is mixed with sufficient recycled uranium complex to raise the weight ratio of uranium to said cations preferably to at least about three. The liquor is then extracted with at least enough non-interfering, water-immiscible, organic solvent to theoretically extract about all of the uranium in the liquor. The organic solvent contains a reagent which reacts with the uranyl ions to form a complex soluble in the solvent. If the aqueous liquor is acidic, the organic solvent is then scrubbed with water. The organic solvent is stripped with a solution containing at least enough ammonium carbonate to precipitate the uranium complex. A portion of the uranium complex is recycled and the remainder can be collected and calcined to produce U 3 O 8 or UO 2

Uranium

International Nuclear Information System (INIS)

Toens, P.D.

1981-03-01

The geological setting of uranium resources in the world can be divided in two basic categories of resources and are defined as reasonably assured resources, estimated additional resources and speculative resources. Tables are given to illustrate these definitions. The increasing world production of uranium despite the cutback in the nuclear industry and the uranium requirements of the future concluded these lecture notes

Radium 226 and uranium isotopes simultaneously determination in water samples using liquid scintillation counter

International Nuclear Information System (INIS)

Al-Masri, M.S.; Al-Akel, B.; Saaid, S.; Nashawati, A.

2007-04-01

In this work a method has been developed to determine simultaneously Radium 226 and Uranium isotopes in water samples by low back ground Liquid Scintillation Counter. Radium 226 was determined by its progeny Polonium 214 after one month of sample storage in order to achieve the equilibrium between Radium 226 and Polonium 214. Uranium isotopes were determined by subtracting Radium 226 activity from total alpha activity. The method detection limits were 0.049 Bq/L and 0.176 Bq/L for Radium 226 and Uranium isotopes respectively. The repeatability limits were ± 0.32 Bq/L and ± 0.9 Bq/L for Radium 226 and Uranium isotopes respectively. While relative errors were % 9.5 and %18.2 for Radium 226 and Uranium isotopes respectively. On the other hand, the report presented the results of different standard and natural samples.(author)

Concerted Uranium Research in Europe (CURE): toward a collaborative project integrating dosimetry, epidemiology and radiobiology to study the effects of occupational uranium exposure.

Science.gov (United States)

Laurent, Olivier; Gomolka, Maria; Haylock, Richard; Blanchardon, Eric; Giussani, Augusto; Atkinson, Will; Baatout, Sarah; Bingham, Derek; Cardis, Elisabeth; Hall, Janet; Tomasek, Ladislav; Ancelet, Sophie; Badie, Christophe; Bethel, Gary; Bertho, Jean-Marc; Bouet, Ségolène; Bull, Richard; Challeton-de Vathaire, Cécile; Cockerill, Rupert; Davesne, Estelle; Ebrahimian, Teni; Engels, Hilde; Gillies, Michael; Grellier, James; Grison, Stephane; Gueguen, Yann; Hornhardt, Sabine; Ibanez, Chrystelle; Kabacik, Sylwia; Kotik, Lukas; Kreuzer, Michaela; Lebacq, Anne Laure; Marsh, James; Nosske, Dietmar; O'Hagan, Jackie; Pernot, Eileen; Puncher, Matthew; Rage, Estelle; Riddell, Tony; Roy, Laurence; Samson, Eric; Souidi, Maamar; Turner, Michelle C; Zhivin, Sergey; Laurier, Dominique

2016-06-01

The potential health impacts of chronic exposures to uranium, as they occur in occupational settings, are not well characterized. Most epidemiological studies have been limited by small sample sizes, and a lack of harmonization of methods used to quantify radiation doses resulting from uranium exposure. Experimental studies have shown that uranium has biological effects, but their implications for human health are not clear. New studies that would combine the strengths of large, well-designed epidemiological datasets with those of state-of-the-art biological methods would help improve the characterization of the biological and health effects of occupational uranium exposure. The aim of the European Commission concerted action CURE (Concerted Uranium Research in Europe) was to develop protocols for such a future collaborative research project, in which dosimetry, epidemiology and biology would be integrated to better characterize the effects of occupational uranium exposure. These protocols were developed from existing European cohorts of workers exposed to uranium together with expertise in epidemiology, biology and dosimetry of CURE partner institutions. The preparatory work of CURE should allow a large scale collaborative project to be launched, in order to better characterize the effects of uranium exposure and more generally of alpha particles and low doses of ionizing radiation.

Estimation of metallic impurities in uranium by carrier distillation method

International Nuclear Information System (INIS)

Page, A.G.; Godbole, S.V.; Deshkar, S.B.; Joshi, B.D.

1976-01-01

An emission spectrographic method has been standardised for the estimation of twenty-two metallic impurities in uranium using carrier-distillation technique. Silver chloride with a concentration of 5% has been used as the carrier and palladium and gallium are used as internal standards. Precision and accuracy determinations of the synthetic samples indicate 6-15% deviation for most of the elements. Using the method described here, five uranium reference samples received from C.E.A.-France were analysed. The detection limits obtained for Cd, Co and W are lower than those reported in the literature while limits for the remaining elements are comparable to the values reported. The method is suitable for the chemical quality control analysis of uranium used for the Fast Breeder Test Reactor (FBTR) fuel. (author)

Uranium briquettes for irradiation target

Energy Technology Data Exchange (ETDEWEB)

Saliba-Silva, Adonis Marcelo; Garcia, Rafael Henrique Lazzari; Martins, Ilson Carlos; Carvalho, Elita Fontenele Urano de; Durazzo, Michelangelo, E-mail: saliba@ipen.b [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2011-07-01

Direct irradiation on targets inside nuclear research or multiple purpose reactors is a common route to produce {sup 99}Mo-{sup 99m}Tc radioisotopes. Nevertheless, since the imposed limits to use LEU uranium to prevent nuclear armament production, the amount of uranium loaded in target meats has physically increased and new processes have been proposed for production. Routes using metallic uranium thin film and UAl{sub x} dispersion have been used for this purpose. Both routes have their own issues, either by bringing difficulties to disassemble the aluminum case inside hot cells or by generating great amount of alkaline radioactive liquid rejects. A potential route might be the dispersion of powders of LEU metallic uranium and nickel, which are pressed as a blend inside a die and followed by pulse electroplating of nickel. The electroplating provides more strength to the briquettes and creates a barrier for gas evolution during neutronic disintegration of {sup 235}U. A target briquette platted with nickel encapsulated in an aluminum case to be irradiated may be an alternative possibility to replace other proposed targets. This work uses pulse Ni-electroplating over iron powder briquette to simulate the covering of uranium by nickel. The following parameters were applied 10 times for each sample: 900Hz, -0.84A/square centimeters with duty cycle of 0.1 in Watts Bath. It also presented the optical microscopy analysis of plated microstructure section. (author)

Uranium briquettes for irradiation target

International Nuclear Information System (INIS)

Saliba-Silva, Adonis Marcelo; Garcia, Rafael Henrique Lazzari; Martins, Ilson Carlos; Carvalho, Elita Fontenele Urano de; Durazzo, Michelangelo

2011-01-01

Direct irradiation on targets inside nuclear research or multiple purpose reactors is a common route to produce 99 Mo- 99m Tc radioisotopes. Nevertheless, since the imposed limits to use LEU uranium to prevent nuclear armament production, the amount of uranium loaded in target meats has physically increased and new processes have been proposed for production. Routes using metallic uranium thin film and UAl x dispersion have been used for this purpose. Both routes have their own issues, either by bringing difficulties to disassemble the aluminum case inside hot cells or by generating great amount of alkaline radioactive liquid rejects. A potential route might be the dispersion of powders of LEU metallic uranium and nickel, which are pressed as a blend inside a die and followed by pulse electroplating of nickel. The electroplating provides more strength to the briquettes and creates a barrier for gas evolution during neutronic disintegration of 235 U. A target briquette platted with nickel encapsulated in an aluminum case to be irradiated may be an alternative possibility to replace other proposed targets. This work uses pulse Ni-electroplating over iron powder briquette to simulate the covering of uranium by nickel. The following parameters were applied 10 times for each sample: 900Hz, -0.84A/square centimeters with duty cycle of 0.1 in Watts Bath. It also presented the optical microscopy analysis of plated microstructure section. (author)

Recovery of uranium from uranium bearing black shale

International Nuclear Information System (INIS)

Das, Amrita; Yadav, Manoj; Singh, Ajay K.

2016-01-01

Black shale is the unconventional resource of uranium. Recovery of uranium from black shale has been carried out by the following steps: i) size reduction, ii) leaching of uranium in the aqueous medium, iii) fluoride ion removal, iv) solvent extraction of uranium from the aqueous leach solution, v) scrubbing of the loaded solvent after extraction to remove impurities as much as possible and vi) stripping of uranium from the loaded organic into the aqueous phase. Leaching of black shale has been carried out in hydrochloric acid. Free acidity of the leach solution has been determined by potentiometric titration method. Removal of fluoride ions has been done using sodium chloride. Solvent extraction has been carried out by both tributyl phosphate and alamine-336 as extractants. Scrubbing has been tried with oxalic acid and sulphuric acid. Stripping with sodium carbonate solution has been carried out. Overall recovery of uranium is 95%. (author)

Uranium in open ocean: concentration and isotopic composition

International Nuclear Information System (INIS)

Ku, T.L.; Knauss, K.G.; Mathieu, G.G.

1977-01-01

Uranium concentrations and 234 U/ 238 U activity ratios have been determined in 63 seawater samples (nine vertical profiles) from the Atlantic, and Pacific, and Arctic, and the Antarctic oceans, using the alpha-spectrometric method for their determinations. Correlation between uranium and salinity is well manifested by the data from the Arctic and the Antarctic oceans, but such a relation cannot be clearly defined with the +-(1 to 2)% precision of uranium measurements for the Atlantic and Pacific data. At the 95% confidence level: (1) the uranium/salinity ratio is (9.34 + - 0.56) x 10 -8 g/g for the seawater analyzed with salinity ranging from 30.3 to 36.2 per thousand; the uranium concentration of seawater of 35 per thousand salinity is 3.3 5 + - 0.2 μ g l -1 ; (2) the 234 U/ 238 U activity ratio is 1.14 +- 0.03. Uranium isotopes in interstitial waters of the Pacific surface sediments analyzed do not show large concentration differences across the sediment-water interface as suggested by previous measurements. Current estimations of the average world river uranium concentration (0.3 to 0.6 μ g l -1 ) and 234 U/ 238 U ratio (1.2 to 1.3) and of the diffusional 234 U influx from sediments 0.3 dpm cm -2 10 -3 yr -1 ) are essentially consistent with a model which depicts a steady state distribution of uranium in the ocean. However, the 0.3 to 0.6 μ g l -1 value for river uranium may be an upper limit estimate. (author)

Uranium resources, 1983

International Nuclear Information System (INIS)

1983-01-01

The specific character of uranium as energy resources, the history of development of uranium resources, the production and reserve of uranium in the world, the prospect regarding the demand and supply of uranium, Japanese activity of exploring uranium resources in foreign countries and the state of development of uranium resources in various countries are reported. The formation of uranium deposits, the classification of uranium deposits and the reserve quantity of each type are described. As the geological environment of uranium deposits, there are six types, that is, quartz medium gravel conglomerate deposit, the deposit related to the unconformity in Proterozoic era, the dissemination type magma deposit, pegmatite deposit and contact deposit in igneaus rocks and metamorphic rocks, vein deposit, sandstone type deposit and the other types of deposit. The main features of respective types are explained. The most important uranium resources in Japan are those in the Tertiary formations, and most of the found reserve belongs to this type. The geological features, the state of yield and the scale of the deposits in Ningyotoge, Tono and Kanmon Mesozoic formation are reported. Uranium minerals, the promising districts in the world, and the matters related to the exploration and mining of uranium are described. (Kako, I.)

Uranium-series constraints on radionuclide transport and groundwater flow at the Nopal I uranium deposit, Sierra Pena Blanca, Mexico

Energy Technology Data Exchange (ETDEWEB)

Goldstein, S.J.; Abdel-Fattah, A.I.; Murrell, M.T.; Dobson, P.F.; Norman, D.E.; Amato, R.S.; Nunn, A. J.

2009-10-01

Uranium-series data for groundwater samples from the Nopal I uranium ore deposit were obtained to place constraints on radionuclide transport and hydrologic processes for a nuclear waste repository located in fractured, unsaturated volcanic tuff. Decreasing uranium concentrations for wells drilled in 2003 are consistent with a simple physical mixing model that indicates that groundwater velocities are low ({approx}10 m/y). Uranium isotopic constraints, well productivities, and radon systematics also suggest limited groundwater mixing and slow flow in the saturated zone. Uranium isotopic systematics for seepage water collected in the mine adit show a spatial dependence which is consistent with longer water-rock interaction times and higher uranium dissolution inputs at the front adit where the deposit is located. Uranium-series disequilibria measurements for mostly unsaturated zone samples indicate that {sup 230}Th/{sup 238}U activity ratios range from 0.005-0.48 and {sup 226}Ra/{sup 238}U activity ratios range from 0.006-113. {sup 239}Pu/{sup 238}U mass ratios for the saturated zone are <2 x 10{sup -14}, and Pu mobility in the saturated zone is >1000 times lower than the U mobility. Saturated zone mobility decreases in the order {sup 238}U{approx}{sup 226}Ra > {sup 230}Th{approx}{sup 239}Pu. Radium and thorium appear to have higher mobility in the unsaturated zone based on U-series data from fractures and seepage water near the deposit.

Uranium management activities

International Nuclear Information System (INIS)

Jackson, D.; Marshall, E.; Sideris, T.; Vasa-Sideris, S.

2001-01-01

One of the missions of the Department of Energy's (DOE) Oak Ridge Office (ORO) has been the management of the Department's uranium materials. This mission has been accomplished through successful integration of ORO's uranium activities with the rest of the DOE complex. Beginning in the 1980's, several of the facilities in that complex have been shut down and are in the decommissioning process. With the end of the Cold War, the shutdown of many other facilities is planned. As a result, inventories of uranium need to be removed from the Department facilities. These inventories include highly enriched uranium (HEU), low enriched uranium (LEU), normal uranium (NU), and depleted uranium (DU). The uranium materials exist in different chemical forms, including metals, oxides, solutions, and gases. Much of the uranium in these inventories is not needed to support national priorities and programs. (author)

300 Area Uranium Stabilization Through Polyphosphate Injection: Final Report

Energy Technology Data Exchange (ETDEWEB)

Vermeul, Vincent R.; Bjornstad, Bruce N.; Fritz, Brad G.; Fruchter, Jonathan S.; Mackley, Rob D.; Newcomer, Darrell R.; Mendoza, Donaldo P.; Rockhold, Mark L.; Wellman, Dawn M.; Williams, Mark D.

2009-06-30

amendment arrival response data indicate some degree of overlap between the reactive species and thus potential for the formation of calcium-phosphate mineral phases (i.e., apatite formation), the efficiency of this treatment approach was relatively poor. In general, uranium performance monitoring results support the hypothesis that limited long-term treatment capacity (i.e., apatite formation) was established during the injection test. Two separate overarching issues affect the efficacy of apatite remediation for uranium sequestration within the 300 Area: 1) the efficacy of apatite for sequestering uranium under the present geochemical and hydrodynamic conditions, and 2) the formation and emplacement of apatite via polyphosphate technology. In addition, the long-term stability of uranium sequestered via apatite is dependent on the chemical speciation of uranium, surface speciation of apatite, and the mechanism of retention, which is highly susceptible to dynamic geochemical conditions. It was expected that uranium sequestration in the presence of hydroxyapatite would occur by sorption and/or surface complexation until all surface sites have been depleted, but that the high carbonate concentrations in the 300 Area would act to inhibit the transformation of sorbed uranium to chernikovite and/or autunite. Adsorption of uranium by apatite was never considered a viable approach for in situ uranium sequestration in and of itself, because by definition, this is a reversible reaction. The efficacy of uranium sequestration by apatite assumes that the adsorbed uranium would subsequently convert to autunite, or other stable uranium phases. Because this appears to not be the case in the 300 Area aquifer, even in locations near the river, apatite may have limited efficacy for the retention and long-term immobilization of uranium at the 300 Area site..

Provision by the uranium and uranium products

International Nuclear Information System (INIS)

Elagin, Yu.P.

2005-01-01

International uranium market is converted from the buyer market into the seller market. The prices of uranium are high and the market attempts to adapt to changing circumstances. The industry of uranium enrichment satisfies the increasing demands but should to increase ots capacities. On the whole the situation is not stable and every year may change the existing position [ru

Acute and chronic toxicity of uranium compounds to Ceriodaphnia-Daphnia dubia

International Nuclear Information System (INIS)

Pickett, J.B.; Specht, W.L.; Keyes, J.L.

1993-01-01

A study to determine the acute and chronic toxicity of uranyl nitrate, hydrogen uranyl phosphate, and uranium dioxide to the organism Ceriodaphnia dubia was conducted. The toxicity tests were conducted by two independent environmental consulting laboratories. Part of the emphasis for this determination was based on concerns expressed by SCDHEC, which was concerned that a safety factor of 100 must be applied to the previous 1986 acute toxicity result of 0.22 mg/L for Daphnia pulex, This would have resulted in the LETF release limits being based on an instream concentration of 0.0022 mg/L uranium. The NPDES Permit renewal application to SCDHEC utilized the results of this study and recommended that the LETF release limit for uranium be based an instream concentration of 0.004 mg/L uranium. This is based on the fact that the uranium releases from the M-Area LETF will be in the hydrogen uranyl phosphate form, or a uranyl phosphate complex at the pH (6--10) of the Liquid Effluent Treatment Facility effluent stream, and at the pH of the receiving stream (5.5 to 7.0). Based on the chronic toxicity of hydrogen uranyl phosphate, a lower uranium concentration limit for the Liquid Effluent Treatment Facility outfall vs. the existing NPDES permit was recommended: The current NPDES permit ''Guideline'' for uranium at outfall M-004 is 0.500 mg/L average and 1.0 mg/L maximum, at a design flowrate of 60 gpm. It was recommended that the uranium concentration at the M-004 outfall be reduced to 0.28 mg/L average, and 0.56 mg/L, maximum, and to reduce the design flowrate to 30 gpm. The 0.28 mg/L concentration will provide an instream concentration of 0.004 mg/L uranium. The 0.28 mg/L concentration at M-004 is based on the combined flows from A-014, A-015, and A-011 outfalls (since 1985) of 1840 gpm (2.65 MGD) and was the flow rate which was utilized in the 1988 NPDES permit renewal application

Uranium quantification in semen by inductively coupled plasma mass spectrometry

Science.gov (United States)

Todorov, Todor I.; Ejnik, John W.; Guandalini, Gustavo S.; Xu, Hanna; Hoover, Dennis; Anderson, Larry W.; Squibb, Katherine; McDiarmid, Melissa A.; Centeno, Jose A.

2013-01-01

In this study we report uranium analysis for human semen samples. Uranium quantification was performed by inductively coupled plasma mass spectrometry. No additives, such as chymotrypsin or bovine serum albumin, were used for semen liquefaction, as they showed significant uranium content. For method validation we spiked 2 g aliquots of pooled control semen at three different levels of uranium: low at 5 pg/g, medium at 50 pg/g, and high at 1000 pg/g. The detection limit was determined to be 0.8 pg/g uranium in human semen. The data reproduced within 1.4–7% RSD and spike recoveries were 97–100%. The uranium level of the unspiked, pooled control semen was 2.9 pg/g of semen (n = 10). In addition six semen samples from a cohort of Veterans exposed to depleted uranium (DU) in the 1991 Gulf War were analyzed with no knowledge of their exposure history. Uranium levels in the Veterans’ semen samples ranged from undetectable (<0.8 pg/g) to 3350 pg/g. This wide concentration range for uranium in semen is consistent with known differences in current DU body burdens in these individuals, some of whom have retained embedded DU fragments.

Uranium industry framework

International Nuclear Information System (INIS)

Riley, K.

2008-01-01

The global uranium market is undergoing a major expansion due to an increase in global demand for uranium, the highest uranium prices in the last 20 years and recognition of the potential greenhouse benefits of nuclear power. Australia holds approximately 27% of the world's uranium resources (recoverable at under US$80/kg U), so is well placed to benefit from the expansion in the global uranium market. Increasing exploration activity due to these factors is resulting in the discovery and delineation of further high grade uranium deposits and extending Australia's strategic position as a reliable and safe supplier of low cost uranium.

High-temperature thermal conductivity of uranium chromite and uranium niobate

International Nuclear Information System (INIS)

Fedoseev, D.V.; Varshavskaya, I.G.; Lavrent'ev, A.V.; Oziraner, S.N.; Kuznetsova, D.G.

1979-01-01

The technique of determining thermal conductivity coefficient of uranium niobate and uranium chromite on heating with laser radiation is described. Determined is the coefficient of free-convective heat transfer (with provision for a conduction component) by means of a standard specimen. The thermal conductivity coefficients of uranium chromite and niobate were measured in the 1300-1700 K temperature range. The results are presented in a diagram form. It has been calculated, that the thermal conductivity coefficient for uranium niobate specimens is greater in comparison with uranium chromite specimens. The thermal conductivity coefficients of the materials mentioned depend on temperature very slightly. Thermal conductivity of the materials considerably depends on their porosity. The specimens under investigation were fabricated by the pressing method and had the following porosity: uranium chromite - 30 %, uranium niobate - 10 %. Calculation results show, that thermal conductivity of dense uranium chromite is higher than thermal conductivity of dense uranium niobate. The experimental error equals approximately 20 %, that is mainly due to the error of measuring the temperature equal to +-25 deg, with a micropyrometer

Study of reactions between uranium-plutonium mixed oxide and uranium nitride and between uranium oxide and uranium nitride; Etude des reactions entre l`oxyde mixte d`uranium-plutonium et le nitrure d`uranium et entre l`oxyde d`uranium et le nitrure d`uranium

Energy Technology Data Exchange (ETDEWEB)

Lecraz, C

1993-06-11

A new type of combustible elements which is a mixture of uranium nitride and uranium-plutonium oxide could be used for Quick Neutrons Reactors. Three different studies have been made on the one hand on the reactions between uranium nitride (UN) and uranium-plutonium mixed oxide (U,Pu)O{sub 2}, on the other hand on these between UN and uranium oxide UO{sub 2}. They show a sizeable reaction between nitride and oxide for the studied temperatures range (1573 K to 1973 K). This reaction forms a oxynitride compound, MO{sub x} N{sub y} with M=U or M=(U,Pu), whose crystalline structure is similar to oxide`s. Solubility of nitride in both oxides is studied, as the reaction kinetics. (TEC). 32 refs., 48 figs., 22 tabs.

Human resource development for uranium production cycle

International Nuclear Information System (INIS)

Ganguly, C.

2014-01-01

Nuclear fission energy is a viable option for meeting the ever increasing demand for electricity and high quality process heat in a safe, secured and sustainable manner with minimum carbon foot print and degradation of the environment. The growth of nuclear power has shifted from North America and Europe to Asia, mostly in China and India. Bangladesh, Vietnam, Indonesia, Malaysia and the United Arab Emirates are also in the process of launching nuclear power program. Natural uranium is the basic raw material for U-235 and Pu-239, the fuels for all operating and upcoming nuclear power reactors. The present generation of nuclear power reactors are mostly light water cooled and moderated reactor (LWR) and to a limited extent pressurized heavy water reactor (PHWR). The LWRs and PHWRs use low enriched uranium (LEU with around 5% U-235) and natural uranium as fuel in the form of high density UO_2 pellets. The uranium production cycle starts with uranium exploration and is followed by mining and milling to produce uranium ore concentrate, commonly known as yellow cake, and ends with mine and mill reclamation and remediation. Natural uranium and its daughter products, radium and radon, are radioactive and health hazardous to varying degrees. Hence, radiological safety is of paramount importance to uranium production cycle and there is a need to review and share best practices in this area. Human Resource Development (HRD) is yet another challenge as most of the experts in this area have retired and have not been replaced by younger generation because of the continuing lull in the uranium market. Besides, uranium geology, exploration, mining and milling do not form a part of the undergraduate or post graduate curriculum in most countries. Hence, the Technical Co-operation activities of the IAEA are required to be augmented and more country specific and regional training and workshop should be conducted at different universities with the involvement of international experts

Uranium concentrations in the water consumed by the resident population in the vicinity of the Lagoa Real uranium province, Bahia, Brazil

Energy Technology Data Exchange (ETDEWEB)

Silva, Luciana S. [State University of Bahia (UNEB), Campus Caetite, BA (Brazil); Pecequilo, Brigitte R.S.; Sarkis, Jorge; Nisti, Marcelo B., E-mail: brigitte@ipen.br, E-mail: jesarkis@ipen.br, E-mail: mbnisti@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2011-07-01

The Lagoa Real Uranium Province, situated in South Central Bahia in the region of Caetite and Lagoa Real, is considered the most important monomineralic province of Brazil. The urban population who lives in the proximities of this uranium province in the cities of Caetite, Lagoa Real and Livramento uses public supply water, while the inhabitants of the rural area due to long terms of dry weather use water from wells, cisterns, small dams, reservoirs and dikes which are supplied with the rains. In this work it was determined the concentration of uranium in the water consumed by the rural and urban population living in the proximities of the Lagoa Real Uranium Province. The study comprehends 32 sampling spots spread throughout the region of interest. Samples were collected in January and July 2010, covering superficial, underground and public supply water from the region. The uranium concentrations were determined by an inductively coupled plasma mass spectrometer (ICP-MS). Preliminary results showed that the uranium concentrations in the water from the Lagoa Real Uranium Province varied from 0.064 {+-} 0.005 {mu}g.L{sup -1} to 90 {+-} 1,5 {+-}g.L{sup -1}. It was observed that only two of them obtained values higher than the World Health Organization's recommended limit (2011) of 30 {mu}g.L{sup -1} for maximum uranium concentration in the water for human consumption. For a conclusive evaluation, the uranium concentrations results will be analyzed together with total alpha and beta concentrations determined elsewhere for the same samples. (author)

Uranium concentrations in the water consumed by the resident population in the vicinity of the Lagoa Real uranium province, Bahia, Brazil

International Nuclear Information System (INIS)

Silva, Luciana S.; Pecequilo, Brigitte R.S.; Sarkis, Jorge; Nisti, Marcelo B.

2011-01-01

The Lagoa Real Uranium Province, situated in South Central Bahia in the region of Caetite and Lagoa Real, is considered the most important monomineralic province of Brazil. The urban population who lives in the proximities of this uranium province in the cities of Caetite, Lagoa Real and Livramento uses public supply water, while the inhabitants of the rural area due to long terms of dry weather use water from wells, cisterns, small dams, reservoirs and dikes which are supplied with the rains. In this work it was determined the concentration of uranium in the water consumed by the rural and urban population living in the proximities of the Lagoa Real Uranium Province. The study comprehends 32 sampling spots spread throughout the region of interest. Samples were collected in January and July 2010, covering superficial, underground and public supply water from the region. The uranium concentrations were determined by an inductively coupled plasma mass spectrometer (ICP-MS). Preliminary results showed that the uranium concentrations in the water from the Lagoa Real Uranium Province varied from 0.064 ± 0.005 μg.L -1 to 90 ± 1,5 ±g.L -1 . It was observed that only two of them obtained values higher than the World Health Organization's recommended limit (2011) of 30 μg.L -1 for maximum uranium concentration in the water for human consumption. For a conclusive evaluation, the uranium concentrations results will be analyzed together with total alpha and beta concentrations determined elsewhere for the same samples. (author)

Uranium rich granite and uranium productive granite in south China

Energy Technology Data Exchange (ETDEWEB)

Mingyue, Feng; Debao, He [CNNC Key Laboratory of Uranium Resource Exploration and Evaluation Technology, Beijing Research Institute of Uranium Geology (China)

2012-07-15

The paper briefly introduces the differences between uranium rich granite and uranium productive granite in the 5 provinces of South China, and discusses their main characteristics in 4 aspects, the uranium productive granite is highly developed in fracture, very strong in alteration, often occurred as two-mica granite and regularly developed with intermediate-basic and acid dikes. The above characteristics distinguish the uranium productive granite from the uranium rich granite. (authors)

Uranium rich granite and uranium productive granite in south China

International Nuclear Information System (INIS)

Feng Mingyue; He Debao

2012-01-01

The paper briefly introduces the differences between uranium rich granite and uranium productive granite in the 5 provinces of South China, and discusses their main characteristics in 4 aspects, the uranium productive granite is highly developed in fracture, very strong in alteration, often occurred as two-mica granite and regularly developed with intermediate-basic and acid dikes. The above characteristics distinguish the uranium productive granite from the uranium rich granite. (authors)

Estimation of uranium in drinking water samples collected from different locations across Tarapur, India

International Nuclear Information System (INIS)

Dusane, C.B.; Maity, Sukanta; Sahu, S.K.; Pandit, G.G.

2015-01-01

In this study, drinking water samples were collected from different locations across Tarapur, India for screening uranium contents. Uranium concentrations were determined by differential pulse adsorptive stripping voltammetry (DPASV). Uranium concentration in water samples varied in a wide range from 0.6-7.9 μg L -1 . Results were compared with the international water quality guidelines World Health Organization (WHO, 2011) and were found within the permissible limit. Results were also compared with the safe limit values for drinking water recommended by national organization like Atomic Energy Regulatory Board (AERB). (author)

Uranium industry annual 1996

International Nuclear Information System (INIS)

1997-04-01

The Uranium Industry Annual 1996 (UIA 1996) provides current statistical data on the US uranium industry's activities relating to uranium raw materials and uranium marketing. The UIA 1996 is prepared for use by the Congress, Federal and State agencies, the uranium and nuclear electric utility industries, and the public. Data on uranium raw materials activities for 1987 through 1996 including exploration activities and expenditures, EIA-estimated reserves, mine production of uranium, production of uranium concentrate, and industry employment are presented in Chapter 1. Data on uranium marketing activities for 1994 through 2006, including purchases of uranium and enrichment services, enrichment feed deliveries, uranium fuel assemblies, filled and unfilled market requirements, uranium imports and exports, and uranium inventories are shown in Chapter 2. A feature article, The Role of Thorium in Nuclear Energy, is included. 24 figs., 56 tabs

Uranium industry annual 1996

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-04-01

The Uranium Industry Annual 1996 (UIA 1996) provides current statistical data on the US uranium industry`s activities relating to uranium raw materials and uranium marketing. The UIA 1996 is prepared for use by the Congress, Federal and State agencies, the uranium and nuclear electric utility industries, and the public. Data on uranium raw materials activities for 1987 through 1996 including exploration activities and expenditures, EIA-estimated reserves, mine production of uranium, production of uranium concentrate, and industry employment are presented in Chapter 1. Data on uranium marketing activities for 1994 through 2006, including purchases of uranium and enrichment services, enrichment feed deliveries, uranium fuel assemblies, filled and unfilled market requirements, uranium imports and exports, and uranium inventories are shown in Chapter 2. A feature article, The Role of Thorium in Nuclear Energy, is included. 24 figs., 56 tabs.

Production of sized particles of uranium oxides and uranium oxyfluorides

International Nuclear Information System (INIS)

Knudsen, I.E.; Randall, C.C.

1976-01-01

A process is claimed for converting uranium hexafluoride (UF 6 ) to uranium dioxide (UO 2 ) of a relatively large particle size in a fluidized bed reactor by mixing uranium hexafluoride with a mixture of steam and hydrogen and by preliminary reacting in an ejector gaseous uranium hexafluoride with steam and hydrogen to form a mixture of uranium and oxide and uranium oxyfluoride seed particles of varying sizes, separating the larger particles from the smaller particles in a cyclone separator, recycling the smaller seed particles through the ejector to increase their size, and introducing the larger seed particles from the cyclone separator into a fluidized bed reactor where the seed particles serve as nuclei on which coarser particles of uranium dioxide are formed. 9 claims, 2 drawing figures

Uranium 2000 : International symposium on the process metallurgy of uranium

International Nuclear Information System (INIS)

Ozberk, E.; Oliver, A.J.

2000-01-01

The International Symposium on the Process Metallurgy of Uranium has been organized as the thirtieth annual meeting of the Hydrometallurgy Section of the Metallurgical Society of the Canadian Institute of Mining, Metallurgy and Petroleum (CIM). This meeting is jointly organized with the Canadian Mineral Processors Division of CIM. The proceedings are a collection of papers from fifteen countries covering the latest research, development, industrial practices and regulatory issues in uranium processing, providing a concise description of the state of this industry. Topics include: uranium industry overview; current milling operations; in-situ uranium mines and processing plants; uranium recovery and further processing; uranium leaching; uranium operations effluent water treatment; tailings disposal, water treatment and decommissioning; mine decommissioning; and international regulations and decommissioning. (author)

Enriched uranium recovery flowsheet improvements

International Nuclear Information System (INIS)

Holt, D.L.

1986-01-01

Savannah River uses 7.5% TBP to recover and purify enriched uranium. Adequate decontamination from fission products is necessary to reduce personnel exposure and to ensure that the enriched uranium product meets specifications. Initial decontamination of the enriched uranium from the fission products is carried out in the 1A bank, 16 stages of mixer-settlers. Separation of the enriched uranium from the fission product, 95 Zr, has been adequate, but excessive solvent degradation caused by the long phase contact times in the mixer-settlers has limited the 95 Zr decontamination factor (DF). An experimental program is investigating the replacement of the current 1A bank with either centrifugal contactors or a combination of centrifugal contactors and mixer-settlers. Experimental work completed has compared laboratory-scale centrifugal contactors and mixer-settlers for 95 Zr removal efficiencies. Feed solutions spiked with actual plant solutions were used. The 95 Zr DF was significantly better in the mixer-settlers than in the centrifugal contactors. As a result of this experimental study, a hybrid equipment flowsheet has been proposed for plant use. The hybrid equipment flowsheet combines the advantages of both types of solvent extraction equipment. Centrifugal contactors would be utilized in the extraction and initial scrub sections, followed by additional scrub stages of mixer-settlers

Bullet scintigraphy: can gamma camera be used for depleted uranium accident measurements?

International Nuclear Information System (INIS)

Spaic, R.; Markovic, S.; Pavlovic, S.; Radic, Z.; Pavlovic, R.; Ajdinovic, B.; Baskot, B.; Djurovic, B.

2002-01-01

The aim of this study was to see could gamma cameras be used for measurement of internal contamination with depleted uranium. Radioactive waste depleted uranium, which is by-product from the production of enriched fuel for nuclear rectors and weapons now, is used for manufacture bullets, which are used in Iraq, Republic of Srpska and Yugoslavia. In this paper is measured minimum detectable activity (MDA) of gamma cameras for depleted uranium, iodine and technetium. For detection of the depleted uranium are used low energy X-rays, energy of 100 keV with 20% windows width. About 40% of gamma emissions of the depleted uranium are in these limits. Measured MDA activities 50-100 Bq for depleted uranium, iodine and technetium are about then times more then same for WBC (5 Bq). Gamma cameras can be used for relatively measurement of depleted uranium activity, what can be used for absorbed dose estimation. Detection of low level internal contamination with depleted uranium can be done with gamma cameras. (authors)

Uranium Industry Annual, 1992

International Nuclear Information System (INIS)

1993-01-01

The Uranium Industry Annual provides current statistical data on the US uranium industry for the Congress, Federal and State agencies, the uranium and electric utility industries, and the public. The feature article, ''Decommissioning of US Conventional Uranium Production Centers,'' is included. Data on uranium raw materials activities including exploration activities and expenditures, resources and reserves, mine production of uranium, production of uranium concentrate, and industry employment are presented in Chapter 1. Data on uranium marketing activities including domestic uranium purchases, commitments by utilities, procurement arrangements, uranium imports under purchase contracts and exports, deliveries to enrichment suppliers, inventories, secondary market activities, utility market requirements, and uranium for sale by domestic suppliers are presented in Chapter 2

Uranium Industry Annual, 1992

Energy Technology Data Exchange (ETDEWEB)

1993-10-28

The Uranium Industry Annual provides current statistical data on the US uranium industry for the Congress, Federal and State agencies, the uranium and electric utility industries, and the public. The feature article, ``Decommissioning of US Conventional Uranium Production Centers,`` is included. Data on uranium raw materials activities including exploration activities and expenditures, resources and reserves, mine production of uranium, production of uranium concentrate, and industry employment are presented in Chapter 1. Data on uranium marketing activities including domestic uranium purchases, commitments by utilities, procurement arrangements, uranium imports under purchase contracts and exports, deliveries to enrichment suppliers, inventories, secondary market activities, utility market requirements, and uranium for sale by domestic suppliers are presented in Chapter 2.

Chemical toxicity and radiological health detriment associated with the inhalation of various enrichments of uranium

International Nuclear Information System (INIS)

3C Limited, Queen Square House, 18-21 Queen Square, Bristol BS1 4NH (United Kingdom))" data-affiliation=" (SR3C Limited, Queen Square House, 18-21 Queen Square, Bristol BS1 4NH (United Kingdom))" >Bryant, P A

2014-01-01

The occupational risks associated with the chemical toxicity of uranium can be overlooked during the processing, handling and storage of the material, as the radioactivity of the material is often used alone to assess the health consequences of exposure to uranium compounds. This note provides a summary of the current United Kingdom occupational standards for uranium based on radiation dose and/or chemical toxicity with a particular focus on intake via inhalation. A simple model is subsequently presented to allow a comparison to be drawn between the occupational exposure standard for chemical toxicity and radiological dose limit. Using these data a set of suggested limits on occupational exposure to airborne uranium is proposed that indicate where the legal annual radiological dose limit for workers or the Health and Safety Executive occupational exposure standard for chemical toxicity are at risk of being breached. (note)

Depleted uranium

International Nuclear Information System (INIS)

Huffer, E.; Nifenecker, H.

2001-02-01

This document deals with the physical, chemical and radiological properties of the depleted uranium. What is the depleted uranium? Why do the military use depleted uranium and what are the risk for the health? (A.L.B.)

Pyrophoric behaviour of uranium hydride and uranium powders

Science.gov (United States)

Le Guyadec, F.; Génin, X.; Bayle, J. P.; Dugne, O.; Duhart-Barone, A.; Ablitzer, C.

2010-01-01

Thermal stability and spontaneous ignition conditions of uranium hydride and uranium metal fine powders have been studied and observed in an original and dedicated experimental device placed inside a glove box under flowing pure argon. Pure uranium hydride powder with low amount of oxide (Oxidation mechanisms are proposed.

RECOVERY OF URANIUM FROM ZIRCONIUM-URANIUM NUCLEAR FUELS

Science.gov (United States)

Gens, T.A.

1962-07-10

An improvement was made in a process of recovering uranium from a uranium-zirconium composition which was hydrochlorinated with gsseous hydrogen chloride at a temperature of from 350 to 800 deg C resulting in volatilization of the zirconium, as zirconium tetrachloride, and the formation of a uranium containing nitric acid insoluble residue. The improvement consists of reacting the nitric acid insoluble hydrochlorination residue with gaseous carbon tetrachloride at a temperature in the range 550 to 600 deg C, and thereafter recovering the resulting uranium chloride vapors. (AEC)

Single-molecule magnetism in a single-ion triamidoamine uranium(V) terminal mono-oxo complex

Energy Technology Data Exchange (ETDEWEB)

King, David M.; McMaster, Jonathan; Lewis, William; Blake, Alexander J.; Liddle, Stephen T. [School of Chemistry, University of Nottingham (United Kingdom); Tuna, Floriana; McInnes, Eric J.L. [School of Chemistry and Photon Science Institute, University of Manchester (United Kingdom)

2013-04-26

Straightforward oxidation of a triamidoamine uranium(III) complex with trimethyl-N-oxide affords a uranium(V) terminal mono-oxo complex which is the first clear-cut example of a uranium(V) single-molecule magnet (SMM). This monometallic complex unambiguously shows that a strongly axially ligated and thus anisotropic ligand field can be used to overcome the limited magnetic anisotropy of uranium(V). (Copyright copyright 2013 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Single-molecule magnetism in a single-ion triamidoamine uranium(V) terminal mono-oxo complex

International Nuclear Information System (INIS)

King, David M.; McMaster, Jonathan; Lewis, William; Blake, Alexander J.; Liddle, Stephen T.; Tuna, Floriana; McInnes, Eric J.L.

2013-01-01

Straightforward oxidation of a triamidoamine uranium(III) complex with trimethyl-N-oxide affords a uranium(V) terminal mono-oxo complex which is the first clear-cut example of a uranium(V) single-molecule magnet (SMM). This monometallic complex unambiguously shows that a strongly axially ligated and thus anisotropic ligand field can be used to overcome the limited magnetic anisotropy of uranium(V). (Copyright copyright 2013 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Standard test method for the determination of uranium by ignition and the oxygen to uranium (O/U) atomic ratio of nuclear grade uranium dioxide powders and pellets

CERN Document Server

American Society for Testing and Materials. Philadelphia

2000-01-01

1.1 This test method covers the determination of uranium and the oxygen to uranium atomic ratio in nuclear grade uranium dioxide powder and pellets. 1.2 This test method does not include provisions for preventing criticality accidents or requirements for health and safety. Observance of this test method does not relieve the user of the obligation to be aware of and conform to all international, national, or federal, state and local regulations pertaining to possessing, shipping, processing, or using source or special nuclear material. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4 This test method also is applicable to UO3 and U3O8 powder.

Measurement of uranium in soil environment optimization of liquid fluorescent method improvement

International Nuclear Information System (INIS)

Qin Guangcheng; Li Yan

2013-01-01

Measurement of uranium in soil environment were introduced in this paper optimization improvement fluid fluorescence analysis method. Use 'on the determination of uranium in soil, rocks, etc. Samples of liquid fluorescent method' when measuring low environment soil samples can not meet the required precision of 8% or less in gansu province and method detection limit of 0.3 mg/kg or less. In affecting the method detection limit, recovery rate and precision of the soil sample decomposition temperature, measuring the temperature of the sample, sample pH value measurement, the background fluorescence measurement condition optimization of analysis is determined, the method detection limit of 0.133 mg/kg, the average recovery rate was 96.6%, the precision is 3.80%. The experimental results show that the method can meet the requirements for determination of trace uranium m environment soil samples. (authors)

Regulatory aspects of uranium remediation in Hungary

International Nuclear Information System (INIS)

Csoevari, M.; Csicsak, J.; Lendvai, Zs.; Varhegyi, A.; Nam, A.

2001-01-01

In Hungary, there are numerous acts and decrees concerning the uranium ore mining remediation, including the aspects of radiation protection and release limits. The most important ones are: Mining Act, Atomic Energy Act, Environmental Protection Act, Water Management Act, Government Decrees No. 115/1993 and 152/1995. For radiation protection regulation the baselines are codified in the Hungarian National Standard MSZ 62/1-1989, while the release limits are prescribed in the order No. 3/1984 of Hungarian Water Authority (OVH), and in the standard MSZ 450/1-1989. According to the above documents, the limits for annual effective dose-equivalent are: (a) 50 mSv for persons occupied in nuclear industry or working with radioactive isotopes, this is relevant to mining and processing of uranium ore, (b) 5 mSv for the critical group of members of the public, in the case of long exposure this value could not exceed 1 mSv/a. In accordance to the EC directives, it is expected that the limit for the public will be decreased soon to 1 mSv/a. Release limits for discharge of natural radionuclides (U, Th, Ra, Rn) in surface water: (a) for uranium maximum 2 mg/dm 3 , (b) for radium-226 maximum 1.1 Bq/dm 3 . There are no general discharge limits for other pollutants in waste water, but the competent authorities may give individual limits if asked. Detailed limits are given only for drinking water for toxic and chemical components. Release limits for discharge of heavy metals are listed in order No. 3/1984 OVH. Of course, numerous licenses and permissions have to be obtained for remediation. The most important ones are the Environmental Protection Permission, based on a detailed environmental impact assessment, and the technical reclamation plans. Numerous authorities are involved in the licensing procedures (e.g. Mining Authority, Environmental Protection Authority, Water Authority, National Municipal Health Authority, etc.). (author)

Literature information applicable to the reaction of uranium oxides with chlorine to prepare uranium tetrachloride

International Nuclear Information System (INIS)

Haas, P.A.

1992-02-01

The reaction of uranium oxides and chlorine to prepare anhydrous uranium tetrachloride (UCl 4 ) are important to more economical preparation of uranium metal. The most practical reactions require carbon or carbon monoxide (CO) to give CO or carbon dioxide (CO 2 ) as waste gases. The chemistry of U-O-Cl compounds is very complex with valances of 3, 4, 5, and 6 and with stable oxychlorides. Literature was reviewed to collect thermochemical data, phase equilibrium information, and results of experimental studies. Calculations using thermodynamic data can identify the probable reactions, but the results are uncertain. All the U-O-Cl compounds have large free energies of formation and the calculations give uncertain small differences of large numbers. The phase diagram for UCl 4 -UO 2 shows a reaction to form uranium oxychloride (UOCl 2 ) that has a good solubility in molten UCl 4 . This appears more favorable to good rates of reaction than reaction of solids and gases. There is limited information on U-O-Cl salt properties. Information on the preparation of titanium, zirconium, silicon, and thorium tetrachlorides (TiCl 4 , ZrCl 4 , SiCl 4 , ThCl 4 ) by reaction of oxides with chlorine (Cl 2 ) and carbon has application to the preparation of UCl 4

Geology and exploration of the Rum Jungle Uranium Field

International Nuclear Information System (INIS)

Fraser, W.J.

1980-01-01

The Rum Jungle Uranium Field was discovered by a private prospector in 1949. A total of 3530 tonnes of uranium oxide was mined and treated from four ore-bodies by Territory Enterprises Pty. Limited who managed the Rum Jungle Project on behalf of the Australian Atomic Energy Commission until the closure of operations in 1971. One small low grade uranium orebody remains to be developed. Lead, zinc, copper, cobalt and nickel were found zoned sub vertically with uranium at one deposit. One medium sized lead, zinc, copper, cobalt and nickel deposit remains to be developed and one small copper deposit with minor uranium was mined. The basemetal deposits show a regional zoning relationship with the known uranium mineralization. Uranium and basemetal mineralization is hosted by graphitic or chloritic, pyritic shales at the contact with a magnesite. These rocks are in the lower part of a sequence of Lower Proterozoic sediments which unconformably overlie Archaean basement complexes. The sediments and complexes are displaced by Giants Reef Fault and sub-parallel shears and linears may further control mineralization. Nearly 50km of the prospective shale/magnesite contact was tested by total count radiometric surveys, various electrical methods, auger, rotary percussion and diamond drilling. The source for the uranium mineralization was probably the Archaean basement complexes from which uranium was initially deposited as protore by either chemical precipitation or clay adsorption in the shale units or as detrital placers in quartz pebble conglomerates immediately overlying the basement complexes. (author)

Uranium prospecting; La prospection de l'uranium

Energy Technology Data Exchange (ETDEWEB)

Roubault, M. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1955-07-01

This report is an instruction book for uranium prospecting. It appeals to private prospecting. As prospecting is now a scientific and technical research, it cannot be done without preliminary studies. First of all, general prospecting methods are given with a recall of fundamental geologic data and some general principles which are common with all type of prospecting. The peculiarities of uranium prospecting are also presented and in particular the radioactivity property of uranium as well as the special aspect of uranium ores and the aspect of neighbouring ores. In a third part, a description of the different uranium ores is given and separated in two different categories: primary and secondary ores, according to the place of transformation, deep or near the crust surface respectively. In the first category, the primary ores include pitchblende, thorianite and rare uranium oxides as euxenite and fergusonite for example. In the second category, the secondary ores contain autunite and chalcolite for example. An exhaustive presentation of the geiger-Mueller counter is given with the presentation of its different components, its functioning and utilization and its maintenance. The radioactivity interpretation method is showed as well as the elaboration of a topographic map of the measured radioactivity. A brief presentation of other detection methods than geiger-Mueller counters is given: the measurement of fluorescence and a chemical test using the fluorescence properties of uranium salts. Finally, the main characteristics of uranium deposits are discussed. (M.P.)

Quantification of the effect of in-situ generated uranium metal on the experimentally determined O/U ratio of a sintered uranium dioxide fuel pellet

International Nuclear Information System (INIS)

Narasimha Murty, B.; Bharati Misra, U.; Yadav, R.B.; Srivastava, R.K.

2005-01-01

This paper describes quantitatively the effect of in-situ generated uranium metal (that could be formed due to the conducive manufacturing conditions) in a sintered uranium dioxide fuel pellet on the experimentally determined O/U ratio using analytical methods involving dissolution of the pellet material. To quantify the effect of in-situ generated uranium metal in the fuel pellet, a mathematical expression is derived for the actual O/U ratio in terms of the O/U ratio as determined by an experiment involving dissolution of the material and the quantity of uranium metal present in the uranium dioxide pellet. The utility of this derived mathematical expression is demonstrated by tabulating the calculated actual O/U ratios for varying amounts of uranium metal (from 5 to 95% in 5% intervals) and different O/U ratio values (from 2.001 to 2.015 in 0.001 intervals). This paper brings out the necessity of care to be exercised while interpreting the experimentally determined O/U ratio and emphasizes the fact that it is always safer to produce the nuclear fuel with oxygen to uranium ratios well below the specified maximum limit of 2.015. (author)

World uranium resources and Japan's status on its procurement

International Nuclear Information System (INIS)

Imaizumi, Tsunemasa

1979-01-01

The features of uranium are that it is not versatile in use, that its substitutes as nuclear fuel cannot be found, that it cannot be used as fuel unless the processing is made, that it has the nuclear fission property, and that there is some time limit in its value. Therefore uranium lacks charm as the object of resource industries. The market of uranium started as military procurement, and its effects still remain now in some extent. Many mines were closed when the oversupply and the rapid drop of price of uranium occurred once, and such fear is felt even now. The relationship between the suppliers and the consumers of uranium is one to one correspondence, accordingly the mutual cooperation is necessary. One problem is that the intervention by governments into uranium market is unavoidable. In order to bring up the sound and stable market, the obstructing factors must be eliminated. The uranium resources in the free world are about 4.4 million tons. The import of uranium resources is carried out according to the long term procurement contracts. For the consumer countries, there are the risk of embargo, the problems related to the cartel, and the restriction based on nuclear non-proliferation. The trade by establishing the multi-lateral organization, the independent development of foreign mines, and the exploration of resources in Japan are discussed. (Kako, I.)

Use of gamma camera for measurement of the internal contamination with depleted uranium

International Nuclear Information System (INIS)

Spaic, R.; Markovic, S.; Pavlovic, S.; Pavlovic, R.; Ajdinovic, B.; Baskot, B.; Djurovic, B.

2000-01-01

Depleted uranium from radioactive wastes is used for manufacturing bullets used in Iraq, Republic of Serbia and Yugoslavia. These bullets are extremely dense and capable of penetrating heavily armored vehicles. Their medical importance lies in the fact that the bullets contain seventy percent depleted uranium which creates aerosolized particles less than five microns in diameter, small enough to be inhaled, after spontaneous bullet burn at impact. Nuclear medicine scientists must be aware of this and be prepared to measure internal contamination of persons exposed to this radioactive material. Whole body counters (WBC) represent appropriate equipment for this purpose but their availability in developing countries is not sufficient. Gamma camera is an alternative. The minimum detectable activity (MDA) of depleted uranium, iodine and technetium for gamma cameras was measured in this paper. Low energy X-ray 100 KeV with 20% windows are used for the depleted uranium detection. About 40% gamma emissions from depleted uranium fall within these limits. The activities measured (50-100 Bq) are about ten times higher then on WBC (5 Bq). This does not limit the use of gamma cameras for measurement of lung or whole body internal contamination with depleted uranium. (author)

Rapid uranium analysis by delayed neutron counting of neutron activated samples

International Nuclear Information System (INIS)

Papadopoulos, N.N.

1985-01-01

The uranium analyzer at the Nuclear Research Center ''Demokritos'' and the delayed neutron method have been used to determine the uranium content in lignite, in chemically enriched samples and in solutions of extractable uranium. The results are compared with data obtained by other methods. In the case of dissolved extractable uranium. The results are in good agreement with X-ray fluorescence data in the range 100 ppm to 2000 ppm while beyond these limits the discrepancies between neutron and spectrophotometric data are observed. The results for lignite samples are in good agreement with gamma spectrometric data. Discrepancies indicate that more extensive intercomparisons are needed to check the reliability of various methods

Heterogeneous catalysis in fluoride melts - reduction of uranium(V) by hydrogen

Energy Technology Data Exchange (ETDEWEB)

Kelmers, A D; Bennett, M R [Oak Ridge National Lab., Tenn. (USA)

1976-01-01

A necessary step in fuel reprocessing for the Molten-Salt Breeder Reactor is the reduction of pentavalent uranium to tetravalent uranium by hydrogen gas. The pentavalent uranium is dissolved in a mixed fluoride melt. Results are presented which show that the hydrogen reduction is rate limited, possibly due to the dissociation of hydrogen molecules to yield active hydrogen atoms; and that by the application of platinum catalysts a 10- to 100-fold increase in the reaction rate can be achieved.

Fluorimetric routine determination of uranium in urine samples

International Nuclear Information System (INIS)

Widua, L.; Schieferdecker, H.; Hezel, U.

With a modified RA 2 reflectance accessory for the Zeiss PMQII/PMQ3 spectrophotometer, uranium in urine was detected with higher sensitivity. A quick method is now available with a detection limit of <2 μg U/1 urine for the determination of possible uranium incorporations, whose sensitivity meets the requirements of radiation protection. Compared with other extraction methods, the instrument outlay and the required working time are small. The total error of the method is below 5 percent

Uranium supply and demand

Energy Technology Data Exchange (ETDEWEB)

Spriggs, M J

1976-01-01

Papers were presented on the pattern of uranium production in South Africa; Australian uranium--will it ever become available; North American uranium resources, policies, prospects, and pricing; economic and political environment of the uranium mining industry; alternative sources of uranium supply; whither North American demand for uranium; and uranium demand and security of supply--a consumer's point of view. (LK)

ERA's Ranger uranium mine

International Nuclear Information System (INIS)

Davies, W.

1997-01-01

Energy Resource of Australia (ERA) is a public company with 68% of its shares owned by the Australian company North Limited. It is currently operating one major production centre - Ranger Mine which is 260 kilometres east of Darwin, extracting and selling uranium from the Ranger Mine in the Northern Territory to nuclear electricity utilities in Japan, South Korea, Europe and North America. The first drum of uranium oxide from Ranger was drummed in August 1981 and operations have continued since that time. ERA is also in the process of working towards obtaining approvals for the development of a second mine - Jabiluka which is located 20 kilometres north of Ranger. The leases of Ranger and Jabiluka adjoin. The Minister for the Environment has advised the Minister for Resources and Energy that there does not appear to be any environmental issue which would prevent the preferred Jabiluka proposal from proceeding. Consent for the development of ERA's preferred option for the development of Jabiluka is being sought from the Aboriginal Traditional Owners. Ranger is currently the third largest producing uranium mine in the world producing 4,237 tonnes of U 3 O 8 in the year to June 1997

Protection of uranium by metallic coatings

International Nuclear Information System (INIS)

Baque, P.; Koch, P.; Dominget, R.; Darras, R.

1968-01-01

A study is made of the possibilities of inhibiting or limiting, by means of protective metallic coatings, the oxidation of uranium by carbon dioxide at high temperature. In general, surface films containing intermetallic compounds or solid solutions of uranium with aluminium, zirconium, copper, niobium, nickel or chromium are formed, according to the techniques employed which are described here. The processes most to be recommended are those of direct diffusion starting from a thin sheet or tube, of vacuum deposition, or of immersion in a molten bath of suitable composition. The conditions for preparing these coatings have been optimized as a function of the protective effect obtained in carbon dioxide at 450 or at 500 C. Only the aluminium and zirconium based coatings are really satisfactory since they can lead to a reduction by a factor of 5 to 10 in the oxidation rate of uranium in the conditions considered; they make it possible in particular to avoid or to reduce to a very large extent the liberation of powdered oxide. Furthermore, the coatings produced generally give the uranium good protection against atmospheric corrosion. (author) [fr

Uranium industry annual, 1991

International Nuclear Information System (INIS)

1992-10-01

In the Uranium Industry Annual 1991, data on uranium raw materials activities including exploration activities and expenditures, resources and reserves, mine production of uranium, production of uranium concentrate, and industry employment are presented in Chapter 1. Data on uranium marketing activities including domestic uranium purchases, commitments by utilities, procurement arrangements, uranium imports under purchase contracts and exports, deliveries to enrichment suppliers, inventories, secondary market activities, utility market requirements, and uranium for sale by domestic suppliers are presented in Chapter 2. A feature article entitled ''The Uranium Industry of the Commonwealth of Independent States'' is included in this report

Fluorimetric determination of uranium in water; Determinacion fluorimetrica de uranio en aguas

Energy Technology Data Exchange (ETDEWEB)

Acosta L, E. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico)]. e-mail: eal@nuclear.inin.mx

1992-02-15

The fluorimetric method for the determination of microquantities of uranium in water is described. This method covers the determination of uranium in water in the interval from 0.2 to 50 ppm on 50 ml. of radioactive base sample. These limits can be variable if the volume of the aliquot one of the base sample is changed, as well as the volume of the used aliquot one for to the final determination of uranium. (Author)

Comparation studies of uranium analysis method using spectrophotometer and voltammeter

International Nuclear Information System (INIS)

Sugeng Pomomo

2013-01-01

Comparation studies of uranium analysis method by spectrophotometer and voltammeter had been done. The objective of experiment is to examine the reliability of analysis method and instrument performance by evaluate parameters; linearity, accuracy, precision and detection limit. Uranyl nitrate hexahydrate is used as standard, and the sample is solvent mixture of tributyl phosphate and kerosene containing uranium (from phosphoric acid purification unit Petrokimia Gresik). Uranium (U) stripping in the sample use HN0 3 0,5 N and then was analyzed by using of both instrument. Analysis of standard show that both methods give a good linearity by correlation coefficient > 0,999. Spectrophotometry give accuration 99,34 - 101,05 % with ratio standard deviation (RSD) 1,03 %; detection limit (DL) 0,05 ppm. Voltammetry give accuration 95,63 -101,49 % with RSD 3,91 %; detection limit (DL) 0,509 ppm. On the analysis of sludge samples were given the significantly different in result; spectrophotometry give U concentration 4,445 ppm by RSD 6,74 % and voltammetry give U concentration 7,693 by RSD 19,53%. (author)

Evaluation of Uranium Measurements in Water by Various Methods - 13571

Energy Technology Data Exchange (ETDEWEB)

Tucker, Brian J. [Shaw Environmental and Infrastructure Group, 150 Royall Street, Canton, MA (United States); Workman, Stephen M. [ALS Laboratory Group, Environmental Division, 225 Commerce Drive, Fort Collins, CO 80524 (United States)

2013-07-01

In December 2000, EPA amended its drinking water regulations for radionuclides by adding a Maximum Contaminant Level (MCL) for uranium (so called MCL Rule)[1] of 30 micrograms per liter (μg/L). The MCL Rule also included MCL goals of zero for uranium and other radionuclides. Many radioactively contaminated sites must test uranium in wastewater and groundwater to comply with the MCL rule as well as local publicly owned treatment works discharge limitations. This paper addresses the relative sensitivity, accuracy, precision, cost and comparability of two EPA-approved methods for detection of total uranium: inductively plasma/mass spectrometry (ICP-MS) and alpha spectrometry. Both methods are capable of measuring the individual uranium isotopes U-234, U- 235, and U-238 and both methods have been deemed acceptable by EPA. However, the U-238 is by far the primary contributor to the mass-based ICP-MS measurement, especially for naturally-occurring uranium, which contains 99.2745% U-238. An evaluation shall be performed relative to the regulatory requirement promulgated by EPA in December 2000. Data will be garnered from various client sample results measured by ALS Laboratory in Fort Collins, CO. Data shall include method detection limits (MDL), minimum detectable activities (MDA), means and trends in laboratory control sample results, performance evaluation data for all methods, and replicate results. In addition, a comparison will be made of sample analyses results obtained from both alpha spectrometry and the screening method Kinetic Phosphorescence Analysis (KPA) performed at the U.S. Army Corps of Engineers (USACE) FUSRAP Maywood Laboratory (UFML). Many uranium measurements occur in laboratories that only perform radiological analysis. This work is important because it shows that uranium can be measured in radiological as well as stable chemistry laboratories and it provides several criteria as a basis for comparison of two uranium test methods. This data will

Evaluation of Uranium Measurements in Water by Various Methods - 13571

International Nuclear Information System (INIS)

Tucker, Brian J.; Workman, Stephen M.

2013-01-01

In December 2000, EPA amended its drinking water regulations for radionuclides by adding a Maximum Contaminant Level (MCL) for uranium (so called MCL Rule)[1] of 30 micrograms per liter (μg/L). The MCL Rule also included MCL goals of zero for uranium and other radionuclides. Many radioactively contaminated sites must test uranium in wastewater and groundwater to comply with the MCL rule as well as local publicly owned treatment works discharge limitations. This paper addresses the relative sensitivity, accuracy, precision, cost and comparability of two EPA-approved methods for detection of total uranium: inductively plasma/mass spectrometry (ICP-MS) and alpha spectrometry. Both methods are capable of measuring the individual uranium isotopes U-234, U- 235, and U-238 and both methods have been deemed acceptable by EPA. However, the U-238 is by far the primary contributor to the mass-based ICP-MS measurement, especially for naturally-occurring uranium, which contains 99.2745% U-238. An evaluation shall be performed relative to the regulatory requirement promulgated by EPA in December 2000. Data will be garnered from various client sample results measured by ALS Laboratory in Fort Collins, CO. Data shall include method detection limits (MDL), minimum detectable activities (MDA), means and trends in laboratory control sample results, performance evaluation data for all methods, and replicate results. In addition, a comparison will be made of sample analyses results obtained from both alpha spectrometry and the screening method Kinetic Phosphorescence Analysis (KPA) performed at the U.S. Army Corps of Engineers (USACE) FUSRAP Maywood Laboratory (UFML). Many uranium measurements occur in laboratories that only perform radiological analysis. This work is important because it shows that uranium can be measured in radiological as well as stable chemistry laboratories and it provides several criteria as a basis for comparison of two uranium test methods. This data will

Determination of uranium in ground water using different analytical techniques

International Nuclear Information System (INIS)

Sahu, S.K.; Maity, Sukanta; Bhangare, R.C.; Pandit, G.G.; Sharma, D.N.

2014-10-01

The concern over presence of natural radionuclides like uranium in drinking water is growing recently. The contamination of aquifers with radionuclides depends on number of factors. The geology of an area is the most important factor along with anthropogenic activities like mining, coal ash disposal from thermal power plants, use of phosphate fertilizers etc. Whatever may be the source, the presence of uranium in drinking waters is a matter of great concern for public health. Studies show that uranium is a chemo-toxic and nephrotoxic heavy metal. This chemotoxicity affects the kidneys and bones in particular. Seeing the potential health hazards from natural radionuclides in drinking water, many countries worldwide have adopted the guideline activity concentration for drinking water quality recommended by the WHO (2011). For uranium, WHO has set a limit of 30μgL-1 in drinking water. The geological distribution of uranium and its migration in environment is of interest because the element is having environmental and exposure concerns. It is of great interest to use an analytical technique for uranium analysis in water which is highly sensitive especially at trace levels, specific and precise in presence of other naturally occurring major and trace metals and needs small amount of sample. Various analytical methods based on the use of different techniques have been developed in the past for the determination of uranium in the geological samples. The determination of uranium requires high selectivity due to its strong association with other elements. Several trace level wet chemistry analytical techniques have been reported for uranium determination, but most of these involve tedious and pain staking procedures, high detection limits, interferences etc. Each analytical technique has its own merits and demerits. Comparative assessment by different techniques can provide better quality control and assurance. In present study, uranium was analysed in ground water samples

Method validation for uranium content analysis using a potentiometer T-90

International Nuclear Information System (INIS)

Torowati; Ngatijo; Rahmiati

2016-01-01

An experimental method validation has been conducted for uranium content analysis using Potentiometer T-90. The method validation experiment was performed in the quality control laboratory of Experiment Fuel Element Installation, PTBBN - BATAN. The objective is to determine the level of precision and accuracy of analytical results for uranium analysis referring to the latest American Standard Test Method (ASTM) of ASTM C1267-11, which is a modified reference method by reducing of reagent consumption by 10% of the amount used by the original method. The ASTM C 1267-11 reference is a new ASTM as a substitute for the older ASTM namely ASTM C799, Vol.12.01, 2003. It is, therefore, necessary to validate the renewed method. The tool used for the analysis of uranium was potentiometer T-90 and the material used was standard uranium oxide powder CRM (Certificate Reference Material). Validation of the method was done by analyzing standard uranium powder by 7 times weighing and 7 times analysis. Analysis results were used to determine the level of accuracy, precision, Relative Standard Deviation (RSD) and Horwitz coefficient Variation and limit detection and quantitation. The average uranium obtained for this method validation is 84.36% with Standard Deviation (SD) of 0.12%, Relative Standard Deviation (RSD) 0.14% and 2/3 Horwitz coefficient Variation (CV Horwitz) 2.05%. The results show that RSD value is smaller than the value of (2/3) CV Horwitz, which means that this method has a high precision. The accuracy value obtained is 0.48%, and since the acceptance limit of high level of accuracy is when the accuracy value is <2.00%, this method is regarded as having a high degree of accuracy [1]. The limit of detection (LOD) and and the limit of quantitation (LOQ) are 0.0145 g/L and 0.0446 g/L respectively. It is concluded that the ASTM C 1267-11 reference method is valid for use. (author)

Uranium price reporting systems

International Nuclear Information System (INIS)

1987-09-01

This report describes the systems for uranium price reporting currently available to the uranium industry. The report restricts itself to prices for U 3 O 8 natural uranium concentrates. Most purchases of natural uranium by utilities, and sales by producers, are conducted in this form. The bulk of uranium in electricity generation is enriched before use, and is converted to uranium hexafluoride, UF 6 , prior to enrichment. Some uranium is traded as UF 6 or as enriched uranium, particularly in the 'secondary' market. Prices for UF 6 and enriched uranium are not considered directly in this report. However, where transactions in UF 6 influence the reported price of U 3 O 8 this influence is taken into account. Unless otherwise indicated, the terms uranium and natural uranium used here refer exclusively to U 3 O 8 . (author)

Simple and selective method for determination of microgram quantities of uranium-238 in urine

International Nuclear Information System (INIS)

Pavlovskaya, N.A.; Martakova, P.I.

1977-01-01

A technique has been developed and described to determine microgram quantities of uranium-238 in urea. The subject of the technique is as follows: urea (50-500 ml) is acidified with hydrochloric acid, and uranium(6) is quantitatively isolated by its coprecipitation with methylviolet rhodanide; the precipitate is separated by centrifuging and mineralized in the presence of nitric and chloric acids; then uranium (6) is reduced into uranium(4) and its amount is determined photoelectrocolorimetrically using the ''arsenazo 3'' reagent. The limiting amount of uranium in a sample being determined is 10 -6 . For a sample volume of 500 ml sensitivity of the technique of uranium determination is 2x10 -9 g/ml. Titanium, thorium and niobium do not interfere with determination of uranium

Indirect determination of uranium by atomic-absorption spectrophotometry using an air-acetylene flame

International Nuclear Information System (INIS)

Alder, J.F.; Das, B.C.

1977-01-01

An indirect method has been developed for the determination of uranium by atomic-absorption spectrophotometry using an air-acetylene flame. Use is made of the reduction of copper(II) by uranium(IV) followed by complex formation of the copper(I) ions so produced with neocuproine (2,9-dimethyl-1,10-phenanthroline) and finally the determination of copper in this complex by atomic-absorption spectrophotometry. The results show that the method can be recommended, provided that care is taken to ensure the complete reduction of uranium(VI) to uranium(IV). The sensitivity of the method is 4.9 μg of uranium and the upper limit 500 μg without dilution. (author)

Formation mechanism of uranium minerals at sandstone-type uranium deposits

International Nuclear Information System (INIS)

Li Shengfu; Zhang Yun

2004-01-01

By analyzing the behavior and existence form of uranium in different geochemical environments, existence form of uranium and uranium minerals species, this paper expounds the formation mechanism of main commercial uranium mineral--pitchblende: (1) uranium is a valence-changeable element. It is reactivated and migrates in oxidized environment, and is reduced and precipitated in reducing environment; (2) [UO 2 (CO 3 ) 3 ] 4- , [UO 2 (CO 3 ) 2 ] 2- coming from oxidized environment react with reductants such as organic matter, sulfide and low-valence iron at the redox front to form simple uranium oxide--pitchblende; (3)the adsorption of uranium by organic matter and clay minerals accelerates the reduction and the concentration of uranium. Therefore, it is considered, that the reduction of SO 4 2- by organic matter to form H 2 S, and the reduction of UO 2 2+ by H 2 S are the main reasons for the formation of pitchblende. This reaction is extensively and universally available in neutral and weakly alkaline carbonate solution. The existense of reductants such as H 2 S is the basic factor leading to the decrease of Eh in environments and the oversaturation of UO 2 2+ at the redox front in groundwater, thus accelerating the adsorption and the precipitation of uranium

Uranium enrichment

International Nuclear Information System (INIS)

1990-01-01

This report looks at the following issues: How much Soviet uranium ore and enriched uranium are imported into the United States and what is the extent to which utilities flag swap to disguise these purchases? What are the U.S.S.R.'s enriched uranium trading practices? To what extent are utilities required to return used fuel to the Soviet Union as part of the enriched uranium sales agreement? Why have U.S. utilities ended their contracts to buy enrichment services from DOE?

International Uranium Resources Evaluation Project (IUREP) national favourability studies: Thailand

International Nuclear Information System (INIS)

1977-08-01

Thailand is a country with an area of 514?000 square kilometres situated in the centre of continental south-east Asia, The geology of Thailand is very varied with sedimentary formations ranging from Cambrian to Quaternary in age and including sandstones, shales, limestones of many varieties. Among the igneous rocks, granites are very important and rhyolites, tuffs diorites, basalts and ultrabasic rocks also exist. Tin is the most important mineral occurrence. Available information on the geology and mineral resources suggests that the country may contain significant resources of radioactive minerals. Favourable potential host types are; 1) uranium and thorium in monazite in beach sands and tin placer deposits; 2) uranium in sandstones, principally in Jurassic sandstones of the Khorat Plateau; 3) uranium in Tertiary lignite deposits; 4) uranium in veins in granites; 5) uranium related to fluorite deposits; 6) uranium in black shales and phosphates. Uranium mineralization in sedimentary rocks at Phu Wieng was discovered in 1970. The area has been radiometrically grid mapped and limited shallow drilling has shown continuity.of the narrow, carbonaceous, conglomeratic sandstone host bed. No uranium reserves or resources can be stated at the present time, but the favourable geology of the Khorat Plateau, the known uranium occurrence and the very small exploration coverage is possibly indicative of a good future potential. The Speculative Potential is estimated to be between 1000 and 10,000 tonnes uranium. (author)

Australian uranium industry

Energy Technology Data Exchange (ETDEWEB)

Warner, R K

1976-04-01

Various aspects of the Australian uranium industry are discussed including the prospecting, exploration and mining of uranium ores, world supply and demand, the price of uranium and the nuclear fuel cycle. The market for uranium and the future development of the industry are described.

Uranium enrichment plans

International Nuclear Information System (INIS)

Thomas, D.C.; Gagne, R.W.

1978-01-01

The following topics are covered: the status of the Government's existing uranium enrichment services contracts, natural uranium requirements based on the latest contract information, uncertainty in predicting natural uranium requirements based on uranium enrichment contracts, and domestic and foreign demand assumed in enrichment planning

Chapter 1. General information about uranium. 1.5. Mechanical properties

International Nuclear Information System (INIS)

Khakimov, N.; Nazarov, Kh.M.; Mirsaidov, I.U.

2012-01-01

Full text: The mechanical properties of uranium depend on its purity, and which mechanical and thermal regimes are used for reprocessing. The average elasticity module value for cast uranium is 20.5•10"-"2 mega newton/m"2 (20.9•10"-"3 kilogram-force/mm"2), strength limit during tension at room temperature is 372–470 mega newton/m"2 (38–48 kilogram-force/mm"2), strength is increased after hardening from β - and γ - phases; and average rigidity by Brinell 19.6–21.6•10"2 mega newton/m"2 (200–220 kilogram-force/mm"2). Exposure by neutron flux (which occurs in nuclear reactors) changes the physical and mechanical properties of uranium: creeping develops and brittleness increases, goods deformation is observed, which forces the operator to use uranium in nuclear reactors as different uranium alloys.

Depleted uranium instead of lead in munitions: the lesser evil.

Science.gov (United States)

Jargin, Sergei V

2014-03-01

Uranium has many similarities to lead in its exposure mechanisms, metabolism and target organs. However, lead is more toxic, which is reflected in the threshold limit values. The main potential hazard associated with depleted uranium is inhalation of the aerosols created when a projectile hits an armoured target. A person can be exposed to lead in similar ways. Accidental dangerous exposures can result from contact with both substances. Encountering uranium fragments is of minor significance because of the low penetration depth of alpha particles emitted by uranium: they are unable to penetrate even the superficial keratin layer of human skin. An additional cancer risk attributable to the uranium exposure might be significant only in case of prolonged contact of the contaminant with susceptible tissues. Lead intoxication can be observed in the wounded, in workers manufacturing munitions etc; moreover, lead has been documented to have a negative impact on the intellectual function of children at very low blood concentrations. It is concluded on the basis of the literature overview that replacement of lead by depleted uranium in munitions would be environmentally beneficial or largely insignificant because both lead and uranium are present in the environment.

Depleted uranium instead of lead in munitions: the lesser evil

International Nuclear Information System (INIS)

Jargin, Sergei V

2014-01-01

Uranium has many similarities to lead in its exposure mechanisms, metabolism and target organs. However, lead is more toxic, which is reflected in the threshold limit values. The main potential hazard associated with depleted uranium is inhalation of the aerosols created when a projectile hits an armoured target. A person can be exposed to lead in similar ways. Accidental dangerous exposures can result from contact with both substances. Encountering uranium fragments is of minor significance because of the low penetration depth of alpha particles emitted by uranium: they are unable to penetrate even the superficial keratin layer of human skin. An additional cancer risk attributable to the uranium exposure might be significant only in case of prolonged contact of the contaminant with susceptible tissues. Lead intoxication can be observed in the wounded, in workers manufacturing munitions etc; moreover, lead has been documented to have a negative impact on the intellectual function of children at very low blood concentrations. It is concluded on the basis of the literature overview that replacement of lead by depleted uranium in munitions would be environmentally beneficial or largely insignificant because both lead and uranium are present in the environment. (opinion)

Uranium series disequilibrium measurements at Mol, Belgium

International Nuclear Information System (INIS)

Ivanovich, M.; Wilkins, M.A.

1985-02-01

The contract just completed has funded two parallel uranium series disequilibrium studies and the aims of and the progress to completion of these studies are given in this report. The larger study was concerned with the measurement of uranium series disequilibrium in ground waters derived from sand layers above and below the Boom Clay formation in North East Belgium. The disequilibrium data are analysed in terms of uranium, thorium and radium isotopic geochemistries and in terms of water types and their mixing in the regional groundwater system. It is concluded that most sampled waters are mixtures of younger and older waters. No true old water end-members have been sampled. Simple considerations of the uranium isotopic data indicate that the longest residence times of the sampled waters are not much in excess of 1 to 10 x 10 3 y. Detailed mixing patterns could not be established from this limited data set particularly in the absence of more detailed modelling in conjunction with groundwater hydraulic pressure and flow direction data. (author)

Uranium of Kazakhstan

International Nuclear Information System (INIS)

Tsalyuk, Yu.; Gurevich, D.

2000-01-01

Over 25 % of the world's uranium reserves are concentrated in Kazakhstan. So, the world's largest Shu-Sarysu uranium province is situated on southern Kazakhstan, with resources exceeding 1 billion tonnes of uranium. No less, than 3 unique deposits with resources exceeding 100,000 tonnes are situated here. From the economic point of view the most important thing is that these deposits are suitable for in-situ leaching, which is the cheapest, environmentally friendly and most efficient method available for uranium extracting. In 1997 the Kazatomprom National Joint-Stock Company united all Kazakhstan's uranium enterprises (3 mine and concentrating plants, Volkovgeologiya Joint-Stock Company and the Ulbinskij Metallurgical plant). In 1998 uranium production came to 1,500 tonnes (860 kg in 1997). In 1999 investment to the industry were about $ 30 million. Plans for development of Kazakhstan's uranium industry provide a significant role for foreign partners. At present, 2 large companies (Comeco (Canada), Cogema (France) working in Kazakhstan. Kazakatomprom continues to attract foreign investors. The company's administration announced that in that in next year they have plan to make a radical step: to sell 67 % of stocks to strategic investors (at present 100 % of stocks belongs to state). Authors of the article regard, that the Kazakhstan's uranium industry still has significant reserves to develop. Even if the scenario for the uranium industry could be unfavorable, uranium production in Kazakhstan may triple within the next three to four years. The processing of uranium by the Ulbinskij Metallurgical Plant and the production of some by-products, such as rhenium, vanadium and rare-earth elements, may provide more profits. Obviously, the sale of uranium (as well as of any other reserves) cannot make Kazakhstan a prosperous country. However, country's uranium industry has a god chance to become one of the most important and advanced sectors of national economy

Options for disposal and reapplication of depleted uranium hexafluoride

International Nuclear Information System (INIS)

Fitch, St.H.

2009-01-01

The nuclear renaissance has spurred the need to enrich uranium to fuel power reactors to meet the nation's energy requirements. However, enriching uranium produces the volatile byproduct of DUF 6 tails. In an ambient environment, DUF 6 decomposes into uranium oxides and hydrogen fluoride (HF). This HF component makes DUF 6 unsuitable for disposal as low-level waste. To make DUF 6 suitable for disposal, it must be stabilized in a controlled process by converting it into uranium oxides and fluorine compounds by the processes of de-conversion and fluorine extraction. Once stabilized, the DU and fluorine have reapplication potential that would delay or divert the need for disposal. Certain challenges confound this process, notably the chemical toxicity from elemental fluorine and DU, radiation hazards, limited low-level waste disposal capacity, and potential political and public opposition. (authors)

Determination of uranium content in phosphate ores using different measurement techniques

Directory of Open Access Journals (Sweden)

Mohammad A. Al-Eshaikh

2016-01-01

Full Text Available The most important unconventional source of uranium is found in phosphate deposits; unfortunately, nowadays its exploitation is limited by economic constraints. The uranium concentrations in phosphate ores in the world vary regionally and most countries with large phosphate deposits have either plant in operation to extract uranium or are at the stage of pilot extraction plants. The aim of this investigation is to evaluate uranium content in the Saudi phosphate ores for, at least, two reasons: firstly, upgrading the phosphate quality by removing the uranium content in order to reduce the radioactivity in the fertilizer products. Secondly, getting benefit from the extracted uranium for its domestic use as a fuel in nuclear power and desalination plants. The results of this study show that the uranium concentration in Saudi phosphate rocks is relatively low (less than 100 ppm, which is not economically encouraging for its direct extraction. However, its extraction as a byproduct from the phosphoric acid, which will have higher concentration could be quite promising and worth exploiting.

International Uranium Resources Evaluation Project (IUREP) national favourability studies: El Salvador

International Nuclear Information System (INIS)

1977-08-01

No information is available on past uranium exploration in El Salvador. The foetallogenic map of Central America (ICAITI, 1970) shows no uranium occurrences, and no descriptions of occurrences are available for this study. Information on current uranium exploration in El Salvador is not available. The 1922 mining code, as amended, covers all minerals, with special rules applicable to phosphates, petroleum and other hydrocarbons. The state owns all minerals, including phosphates, except for salt and other common materials. Mineral and surface rights are distinct. Both citizens and aliens may acquire mineral rights. There is a possibility of uranium potential in the clastic sediments containing interbedded volcanics, particularly where the latter are tuffaceous. These rocks occur chiefly in the north western part of the country and are of limited areal extent. The possibility of uranium occurrences associated with acid volcanics cannot be discounted, but it is difficult to evaluate rocks of this type for uranium with the present state of knowledge. Accordingly, potential resources are estimated at between 0 and 1,000 tonnes uranium

Uranium industry vs radioecological risk

International Nuclear Information System (INIS)

Jonchev, L.

1998-01-01

Uranium industry development on a worldwide scale accounts for a technological increase in the natural radiation background as a result of human activity. The higher radionuclide concentration leads to an increase of the radiological risk which is a basic criterion for environmental and human protection. Therefore its determination with regard to the uranium industry and particularly to the process of its closure is mandatory. Restoration and control of the environment is closely linked to a system of criteria and levels for assessment of the radionuclide contamination hazards. Annual individual effective dose of 2.3 mSv is accepted as anormal average level for radiation exposure of the Bulgarian population from the natural radiation background. The value of 3.5 mSv/y is accepted as the uppermost limit of the normal background exposure level. According to ICRP recommendations the additional overbackground exposure of the population should not exceed 1.0 mSv/y towards the background level for the region. This holds true also for areas neighbouring to the uranium mining sites

Standard specification for uranium metal enriched to more than 15 % and less Than 20 % 235U

CERN Document Server

American Society for Testing and Materials. Philadelphia

2000-01-01

1.1 This specification covers nuclear grade uranium metal that has either been processed through an enrichment plant, or has been produced by the blending of highly enriched uranium with other uranium, to obtain uranium of any 235U concentration below 20 % (and greater than 15 %) and that is intended for research reactor fuel fabrication. The scope of this specification includes specifications for enriched uranium metal derived from commercial natural uranium, recovered uranium, or highly enriched uranium. Commercial natural uranium, recovered uranium and highly enriched uranium are defined in Section 3. The objectives of this specification are to define the impurity and uranium isotope limits for commercial grade enriched uranium metal. 1.2 This specification is intended to provide the nuclear industry with a standard for enriched uranium metal which is to be used in the production of research reactor fuel. In addition to this specification, the parties concerned may agree to other appropriate conditions. ...

Adsorptive stripping voltammetric determination of uranium with cephradine

International Nuclear Information System (INIS)

Ali, A.M.M.; Ghandour, M.A.; Khodari, M.

1995-01-01

Uranium adsorbed with cephradine is reduced on a hanging mercury drop electrode. This property was exploited in developing a highly sensitive stripping voltammetric procedure for the determination of uranium. A detection limit 2 x 10 -9 mol I -1 (0.5 μg I -1 ) of uranium ion is obtained with an 180 s accumulation time. Cyclic voltammetry was used to characterize the interfacial and redox behaviour. The effects of various parameters are discussed. Experimental conditions include the use of 5 x 10 -6 mol I -1 cephradine in 0.05 mol I -1 sodium perchlorate (pH ''approx ='' 6.5), an accumulation potential of 0.0 V versus SCE and a direct current stripping technique. The response is linear up to 5 x 10 -6 mol I -1 uranium and the relative standard deviation at 1 x 10 -7 mol I -1 ) UO 2+ is 4.4%. The effect of other metal ions was investigated. (author)

Translocation of uranium from water to foodstuff while cooking.

Science.gov (United States)

Krishnapriya, K C; Baksi, Ananya; Chaudhari, Swathi; Gupta, Soujit Sen; Pradeep, T

2015-10-30

The present work report the unusual uranium uptake by foodstuff, especially those rich in carbohydrates like rice when they are cooked in water, contaminated with uranium. The major staple diet in South Asia, rice, was chosen to study its interaction with UO2(2+), the active uranium species in water, using inductively coupled plasma mass spectrometry. Highest uptake limit was checked by cooking rice at very high uranium concentration and it was found to be good scavenger of uranium. To gain insight into the mechanism of uptake, direct interaction of UO2(2+) with monosaccharides was also studied, using electrospray ionization mass spectrometry taking mannose as a model. The studies have been done with dissolved uranium salt, uranyl nitrate hexahydrate (UO2(NO3)2·6H2O), as well as the leachate of a stable oxide of uranium, UO2(s), both of which exist as UO2(2+) in water. Among the eight different rice varieties investigated, Karnataka Ponni showed the maximum uranium uptake whereas unpolished Basmati rice showed the minimum. Interaction with other foodstuffs (potato, carrot, peas, kidney beans and lentils) with and without NaCl affected the extent of chemical interaction but was not consistent with the carbohydrate content. Uranium interaction with D-mannose monitored through ESI-MS, under optimized instrumental parameters, identified the peaks corresponding to uranyl adduct with mannose monomer, dimer and trimer and the species were confirmed by MS/MS studies. The product ion mass spectra showed peaks illustrating water loss from the parent ion as the collision energy was increased, an evidence for the strong interaction of uranium with mannose. This study would constitute the essential background for understanding interaction of uranium with various foods. Extension of this work would involve identification of foodstuff as green heavy metal scavengers. Copyright © 2015. Published by Elsevier B.V.

Uranium enrichment plans

International Nuclear Information System (INIS)

Gagne, R.W.; Thomas, D.C.

1977-01-01

The status of existing uranium enrichment contracts in the US is reviewed and expected natural uranium requirements for existing domestic uranium enrichment contracts are evaluated. Uncertainty in natural uranium requirements associated with requirements-type and fixed-commitment type contracts is discussed along with implementation of variable tails assay

Uranium speciation in plants

International Nuclear Information System (INIS)

Guenther, A.; Bernhard, G.; Geipel, G.; Reich, T.; Rossberg, A.; Nitsche, H.

2003-01-01

Detailed knowledge of the nature of uranium complexes formed after the uptake by plants is an essential prerequisite to describe the migration behavior of uranium in the environment. This study focuses on the determination of uranium speciation after uptake of uranium by lupine plants. For the first time, time-resolved laser-induced fluorescence spectroscopy and X-ray absorption spectroscopy were used to determine the chemical speciation of uranium in plants. Differences were detected between the uranium speciation in the initial solution (hydroponic solution and pore water of soil) and inside the lupine plants. The oxidation state of uranium did not change and remained hexavalent after it was taken up by the lupine plants. The chemical speciation of uranium was identical in the roots, shoot axis, and leaves and was independent of the uranium speciation in the uptake solution. The results indicate that the uranium is predominantly bound as uranyl(VI) phosphate to the phosphoryl groups. Dandelions and lamb's lettuce showed uranium speciation identical to lupine plants. (orig.)

Kintyre uranium project

International Nuclear Information System (INIS)

1988-04-01

This project book is designed to outline the nature of the Kintyre uranium project for those associated with the project as employees, contractors and consultants and others. It explains why Canning Resources Pty Limited and CRA Exploration believe this resource and other resources in the Rundall region should be developed. It also outlines the environmental and social issues involved and the proposed means of addressing those issues. The Kintyre resource and associated areas of geological prospectivity are located in the Rundall region on the edge of the Great Sandy Desert, in the East Pilbara region of Western Australia. Canning Resources with CRA Exploration has spent over $20 million in the past two years in intensive drilling and exploration efforts in the Kintyre area and intends to spend a further $10 million in 1988. Investigations so far reveal that the resource has features which make it competitive with the best uranium mines in the world

Uranium recovering from slags generated in the metallic uranium by magnesiothermic reduction

International Nuclear Information System (INIS)

Fornarolo, F.; Carvalho, E.F. Urano de; Durazzo, M.; Riella, H.G.

2008-01-01

The Nuclear Fuel Center of IPEN/CNEN-SP has recent/y concluded a program for developing the fabrication technology of the nuclear fuel based on the U 3 Si 2 -Al dispersion, which is being used in the IEA-R1 research reactor. The uranium silicide (U 3 Si 2 ) fuel production starts with the uranium hexafluoride (UF 6 ) processing and uranium tetrafluoride (UF 4 ) precipitation. Then, the UF 4 is converted to metallic uranium by magnesiothermic reduction. The UF 4 reduction by magnesium generates MgF 2 slag containing considerable concentrations of uranium, which could reach 20 wt%. The uranium contained in that slag should be recovered and this work presents the results obtained in recovering the uranium from that slag. The uranium recovery is accomplished by acidic leaching of the calcined slag. The calcination transforms the metallic uranium in U 3 O 8 , promoting the pulverization of the pieces of metallic uranium and facilitating the leaching operation. As process variables, have been considered the nitric molar concentration, the acid excess regarding the stoichiometry and the leaching temperature. As result, the uranium recovery reached a 96% yield. (author)

Oxidizing attack process of uranium ore by a carbonated liquor

International Nuclear Information System (INIS)

Maurel, Pierre; Nicolas, Francois.

1981-01-01

A continuous process for digesting a uraniferous ore by oxidation with a recycling aqueous liquor containing alkaline carbonates and bicarbonates in solution as well as uranium in a concentration close to its solubility limit at digestion temperature, and of recuperation of the precipitated uranium within the solid phase remaining after digestion. The digestion is carried out by spraying oxygen into the hot reactional medium in order not only to permit oxidation of the uranium and its solubilization but also to ensure that the sulphides of impurities and organic substances present in the ore are oxidized [fr

Process for producing uranium oxide rich compositions from uranium hexafluoride

International Nuclear Information System (INIS)

DeHollander, W.R.; Fenimore, C.P.

1978-01-01

Conversion of gaseous uranium hexafluoride to a uranium dioxide rich composition in the presence of an active flame in a reactor defining a reaction zone is achieved by separately introducing a first gaseous reactant comprising a mixture of uranium hexafluoride and a reducing carrier gas, and a second gaseous reactant comprising an oxygen-containing gas. The reactants are separated by a shielding gas as they are introduced to the reaction zone. The shielding gas temporarily separates the gaseous reactants and temporarily prevents substantial mixing and reacting of the gaseous reactants. The flame occurring in the reaction zone is maintained away from contact with the inlet introducing the mixture to the reaction zone. After suitable treatment, the uranium dioxide rich composition is capable of being fabricated into bodies of desired configuration for loading into nuclear fuel rods. Alternatively, an oxygen-containing gas as a third gaseous reactant is introduced when the uranium hexafluoride conversion to the uranium dioxide rich composition is substantially complete. This results in oxidizing the uranium dioxide rich composition to a higher oxide of uranium with conversion of any residual reducing gas to its oxidized form

Formation conditions of uranium minerals in oxidation zone of uranium deposits

International Nuclear Information System (INIS)

Li Youzhu

2005-01-01

The paper concerns about the summary and classification of hydrothermal uranium deposit with oxidation zone. Based on the summary of observation results of forty uranium deposits located in CIS and Bulgaria which are of different sizes and industrial-genetic types, analysis on available published information concerning oxidation and uranium mineral enrichment in supergenic zone, oxidation zone classification of hydrothermal uranium had been put forward according to the general system of the exogenetic uranium concentration. (authors)

Distinction between natural and depleted uranium using instrumental neutron activation analysis

International Nuclear Information System (INIS)

Haddad, Kh.

2008-01-01

A convenient method to discriminate between natural and depleted uranium samples was developed in this work. Traces of natural and depleted uranium were irradiated separately and the ratios of 95 Zr/ 103 Ru, 239 Np/ 95 Zr, 239 Np/ 103 Ru were measured. The results show that these ratios can be used as indicators of the uranium isotopic composition of the sample. These ratios are independent of the secular equilibrium of the 238 U with its daughters in the sample and indicate the isotopic composition for trace amounts. Date and truffle samples has been analysed also using this method. Results show that the uranium content in this product was less than the detection limit.(author)

Uranium industry annual 1994

International Nuclear Information System (INIS)

1995-01-01

The Uranium Industry Annual 1994 (UIA 1994) provides current statistical data on the US uranium industry's activities relating to uranium raw materials and uranium marketing during that survey year. The UIA 1994 is prepared for use by the Congress, Federal and State agencies, the uranium and nuclear electric utility industries, and the public. It contains data for the 10-year period 1985 through 1994 as collected on the Form EIA-858, ''Uranium Industry Annual Survey.'' Data collected on the ''Uranium Industry Annual Survey'' (UIAS) provide a comprehensive statistical characterization of the industry's activities for the survey year and also include some information about industry's plans and commitments for the near-term future. Where aggregate data are presented in the UIA 1994, care has been taken to protect the confidentiality of company-specific information while still conveying accurate and complete statistical data. A feature article, ''Comparison of Uranium Mill Tailings Reclamation in the United States and Canada,'' is included in the UIA 1994. Data on uranium raw materials activities including exploration activities and expenditures, EIA-estimated resources and reserves, mine production of uranium, production of uranium concentrate, and industry employment are presented in Chapter 1. Data on uranium marketing activities, including purchases of uranium and enrichment services, and uranium inventories, enrichment feed deliveries (actual and projected), and unfilled market requirements are shown in Chapter 2

International Uranium Resources Evaluation Project (IUREP) national favourability studies: The Netherlands

International Nuclear Information System (INIS)

1978-01-01

The Netherlands is part of the lowlands of Western Europe formed by negative crustal movements that have been offset by sedimentation. This specific area stretching from western Belgium into north-western Germany forms part of an epicontinental area that has been relatively stable since the end of the Hercynian orogeny. In Holland the subsidence has generally been small through- out the Mesozonic and Cenozoic though interrupted by short periods of erosion and non-subsidence. Thus the general geology of the Netherlands is dominated by the fact that throughout the Tertiary and Quaternary what now comprises the Netherlands formed part of a subsiding basin. Most of the surface geology of the country is dominated by f luvio-glacial shallow marine and lacoustine deposits. Prospecting for radioactive minerals in the Netherlands has been very limited. Some work has been carried out by the Geological Survey and by private consultants but this was very preliminary. To-date no uranium reserves or resources have been identified in the Netherlands. One small uranium occurrence has been recorded in Zeeland near Walcheren where some small uranium concentrations were found in association with phosphatic nodules. Apart from very limited targets in the Cretaceous and small phosphatic uranium associations there are no apparent uranium exploration targets in the Netherlands. On this basis we would, at this time, place the uranium potential of the Netherlands in Group I of the IUREP classification

Comparative statistical analysis of carcinogenic and non-carcinogenic effects of uranium in groundwater samples from different regions of Punjab, India

International Nuclear Information System (INIS)

Saini, Komal; Singh, Parminder; Bajwa, Bikramjit Singh

2016-01-01

LED flourimeter has been used for microanalysis of uranium concentration in groundwater samples collected from six districts of South West (SW), West (W) and North East (NE) Punjab, India. Average value of uranium content in water samples of SW Punjab is observed to be higher than WHO, USEPA recommended safe limit of 30 µg l −1 as well as AERB proposed limit of 60 µg l −1 . Whereas, for W and NE region of Punjab, average level of uranium concentration was within AERB recommended limit of 60 µg l −1 . Average value observed in SW Punjab is around 3–4 times the value observed in W Punjab, whereas its value is more than 17 times the average value observed in NE region of Punjab. Statistical analysis of carcinogenic as well as non carcinogenic risks due to uranium have been evaluated for each studied district. - Highlights: • Uranium level in groundwater samples have been assessed in different regions of Punjab. • Comparative study of carcinogenic and non carcinogenic effects of uranium has been done. • Wide variation has been found for different geological regions. • It has been found that South west Punjab is worst affected by uranium contamination in its water. • For west and north east regions of Punjab, uranium levels in groundwater laid under recommended safe limits.

Research on geochronology and uranium source of sandstone-hosted uranium ore-formation in major uranium-productive basins, Northern-China

International Nuclear Information System (INIS)

Xia Yuliang; Liu Hanbin; Lin Jinrong; Fan Guang; Hou Yanxian

2004-12-01

A method is developed for correcting uranium content in uranium ore samples by considering the U-Ra equilibrium coefficient, then a U-Pb isochron is drawn up. By performing the above correction ore-formation ages of sandstone-hosted uranium mineralization which may be more realistic have been obtained. The comparative research on U-Pb isotopic ages of detritic zircon in ore-hosting sandstone and zircon in intermediate-acid igneous rocks in corresponding provenance area indicates that the ore-hosting sandstone is originated from the erosion of intermediate-acid igneous rocks and the latters are the material basis for the formation of the uranium-rich sandstone beds. On the basis of the study on U-Pb isotopic system evolution of the provenance rocks and sandstones from ore-hosting series, it is verified that the uranium sources of the sandstone-hosted uranium deposit are: the intermediate-acid igneous rocks with high content of mobile uranium, and the sandstone bodies pre-concentrated uranium. (authors)

Control of uranium hazards - Portsmouth uranium enrichment plant

International Nuclear Information System (INIS)

Wagner, E.R.

1985-01-01

This report summarizes the Environmental, Safety and Health programs to control uranium hazards at the Portsmouth Gaseous Diffusion Plant. A description of the physical plant, the facility processes and the attendant uranium flows and effluents are provided. The hazards of uranium are discussed and the control systems are outlined. Finally, the monitoring programs are described and summaries of recent data are provided. 11 figs., 20 tabs

Recommendations concerning an interim annual individual exposure limit for respirable quartz

International Nuclear Information System (INIS)

Stocker, H.; Horvath, F.J.; Napier, W.

1983-07-01

This paper presents AECB staff recommendations on the desirability of an annual individual occupational exposure limit for respirable quartz and on the magnitude of this limit, for uranium miners. Justifications are presented for the magnitude of this suggested limit for respirable quartz, drawing on experience gained in Ontario uranium and non-uranium mines and on that in other countries. The suggestion is made that an exposure limit be set for an interim period in order that additional information on the adequacy of the magnitude of the limit may be acquired. To complement the suggested exposure limit, it is proposed that a co-existing control program of action levels, to be triggered at various respirable quartz concentrations, be set up. It is the contention of this paper that the degree of protection afforded to individuals by the suggested exposure limit would be equivalent to the time-weighted average threshold limit value derived from recommendations, based on group average exposures, of the American Conference of Governmental Industrial Hygienists

Uranium isotopes in carbonate aquifers of arid region setting

International Nuclear Information System (INIS)

Alshamsi, D.M.; Murad, A.A.

2013-01-01

Groundwater in arid and semiarid regions is vital resource for many uses and therefore information about concentrations of uranium isotopes among other chemical parameters are necessary. In the study presented here, distribution of 238 U and 235 U in groundwater of four selected locations in the southern Arabian peninsula, namely at two locations within the United Arab Emirates (UAE) and two locations in Oman are discussed. The analyses of the uranium isotopes were performed using ICP-MS and the results indicated a range of concentrations for 235 U and 238 U at 3-39 ng L -1 (average: 18 ng L -1 ) and 429-5,293 ng L -1 (average: 2,508 ng L -1 ) respectively. These uranium concentrations are below the higher permissible WHO limit for drinking water and also comparable to averages found in groundwater from similar aquifers in Florida and Tunisia. Negative correlation between rainfall and uranium concentrations suggests that in lithologically comparable aquifers, climate may influence the concentration of uranium in subtropical to arid regions. (author)

Sensitivity analysis of uranium solubility under strongly oxidizing conditions

International Nuclear Information System (INIS)

Liu, L.; Neretnieks, I.

1999-01-01

To evaluate the effect of geochemical conditions in the repository on the solubility of uranium under strongly oxidizing conditions, a mathematical model has been developed to determine the solubility, by utilizing a set of nonlinear algebraic equations to describe the chemical equilibria in the groundwater environment. The model takes into account the predominant precipitation-dissolution reactions, hydrolysis reactions and complexation reactions that may occur under strongly oxidizing conditions. The model also includes the solubility-limiting solids induced by the presence of carbonate, phosphate, silicate, calcium, and sodium in the groundwater. The thermodynamic equilibrium constants used in the solubility calculations are essentially taken from the NEA Thermochemical Data Base of Uranium, with some modification and some uranium minerals added, such as soddyite, rutherfordite, uranophane, uranyl orthophosphate, and becquerelite. By applying this model, the sensitivities of uranium solubility to variations in the concentrations of various groundwater component species are systematically investigated. The results show that the total analytical concentrations of carbonate, phosphate, silicate, and calcium in deep groundwater play the most important role in determining the solubility of uranium under strongly oxidizing conditions

Uranium industry annual, 1986

International Nuclear Information System (INIS)

1987-01-01

Uranium industry data collected in the EIA-858 survey provide a comprehensive statistical characterization of annual activities of the industry and include some information about industry plans over the next several years. This report consists of two major sections. The first addresses uranium raw materials activities and covers the following topics: exploration activities and expenditures, resources and reserves, mine production of uranium, production of uranium concentrate, and industry employment. The second major section is concerned with the following uranium marketing activities: uranium purchase commitments, uranium prices, procurement arrangements, uranium imports and exports, enrichment services, inventories, secondary market activities utility market requirements and related topics

Uranium Industry. Annual 1984

International Nuclear Information System (INIS)

Lawrence, M.S.S.

1985-01-01

This report provides a statistical description of activities of the US uranium industry during 1984 and includes a statistical profile of the status of the industry at the end of 1984. It is based on the results of an Energy Information Administration (EIA) survey entitled ''Uranium Industry Annual Survey'' (Form EIA-858). The principal findings of the survey are summarized under two headings - Uranium Raw Materials Activities and Uranium Marketing Activities. The first heading covers exploration and development, uranium resources, mine and mill production, and employment. The second heading covers uranium deliveries and delivery commitments, uranium prices, foreign trade in uranium, inventories, and other marketing activities. 32 figs., 48 tabs

Irradiated uranium reprocessing

International Nuclear Information System (INIS)

Gal, I.

1961-12-01

Task concerned with reprocessing of irradiated uranium covered the following activities: implementing the method and constructing the cell for uranium dissolving; implementing the procedure for extraction of uranium, plutonium and fission products from radioactive uranium solutions; studying the possibilities for using inorganic ion exchangers and adsorbers for separation of U, Pu and fission products

Literature information applicable to the reaction of uranium oxides with chlorine to prepare uranium tetrachloride

Energy Technology Data Exchange (ETDEWEB)

Haas, P.A.

1992-02-01

The reaction of uranium oxides and chlorine to prepare anhydrous uranium tetrachloride (UCl{sub 4}) are important to more economical preparation of uranium metal. The most practical reactions require carbon or carbon monoxide (CO) to give CO or carbon dioxide (CO{sub 2}) as waste gases. The chemistry of U-O-Cl compounds is very complex with valances of 3, 4, 5, and 6 and with stable oxychlorides. Literature was reviewed to collect thermochemical data, phase equilibrium information, and results of experimental studies. Calculations using thermodynamic data can identify the probable reactions, but the results are uncertain. All the U-O-Cl compounds have large free energies of formation and the calculations give uncertain small differences of large numbers. The phase diagram for UCl{sub 4}-UO{sub 2} shows a reaction to form uranium oxychloride (UOCl{sub 2}) that has a good solubility in molten UCl{sub 4}. This appears more favorable to good rates of reaction than reaction of solids and gases. There is limited information on U-O-Cl salt properties. Information on the preparation of titanium, zirconium, silicon, and thorium tetrachlorides (TiCl{sub 4}, ZrCl{sub 4}, SiCl{sub 4}, ThCl{sub 4}) by reaction of oxides with chlorine (Cl{sub 2}) and carbon has application to the preparation of UCl{sub 4}.

Uranium

International Nuclear Information System (INIS)

Anon.

1984-01-01

The article briefly discusses the Australian government policy and the attitude of political party factions towards the mining and exporting of the uranium resources in Australia. Australia has a third of the Western World's low-cost uranium resources

Standard specification for uranium oxides with a 235U content of less than 5 % for dissolution prior to conversion to nuclear-grade uranium dioxide

CERN Document Server

American Society for Testing and Materials. Philadelphia

2005-01-01

1.1 This specification covers uranium oxides, including processed byproducts or scrap material (powder, pellets, or pieces), that are intended for dissolution into uranyl nitrate solution meeting the requirements of Specification C788 prior to conversion into nuclear grade UO2 powder with a 235U content of less than 5 %. This specification defines the impurity and uranium isotope limits for such urania powders that are to be dissolved prior to processing to nuclear grade UO2 as defined in Specification C753. 1.2 This specification provides the nuclear industry with a general standard for such uranium oxide powders. It recognizes the diversity of conversion processes and the processes to which such powders are subsequently to be subjected (for instance, by solvent extraction). It is therefore anticipated that it may be necessary to include supplementary specification limits by agreement between the buyer and seller. 1.3 The scope of this specification does not comprehensively cover all provisions for prevent...

Three-stage method for interpretation of uranium-lead isotopic data

International Nuclear Information System (INIS)

Nejmark, L.A.; Ovchinnikova, G.V.; Levchenkov, O.A.

1982-01-01

Three-dimensional approach for the iterpretation of uranium-lead isoto e ratios in pnatural systems, development of which corresponds to three stages, has been considered. In the framework of the three-stage model two cases, differing in the character of uranium-lead systems violation at the beginning of the third stage, are discussed. The first case corresponds to uranium addition or lead substraction, and the second one - to addition of lead of unknown isotopic content. Three-stage approach permits without amending the isotopic content of lead captured during crystallization to calculated the beginning of the second and third stages of uranium-lead systems development and to evaluate parameters of lead added to the system. Concrete examples of interpretation of uranium-lead isotopic ratios in minerals and rock samples as a whole both of the terrestrial and cosmic origin are considered. Possibilities and limitations of the three-stage approach are analyzed and directions of further development are outlined

Situ leaching uranium mining conditions of the pilot phase of the safety management

International Nuclear Information System (INIS)

Liu Wenyuan

2014-01-01

With China's large, very large sandstone type uranium deposits have been discovered in the Ordos Basin, Inner Mongolia and its surrounding for uranium mining in the region has been carried out. Sandstone-type uranium mining, mainly used in China is 'to dip' and the technology is relatively mature. Situ leaching mining process, the deposit conditions Test conditions pilot phase, however, limited by cost control and field conditions, equipment shabby, out in the conditions of the pilot phase of security issues in the larger securityrisks. This will be Ordos ongoing test conditions situ leaching uranium mines, for example, raised situ leaching uranium mining conditions of the pilot phase a few safety measures recommended. (author)

Uranium industry annual 1998

International Nuclear Information System (INIS)

1999-01-01

The Uranium Industry Annual 1998 (UIA 1998) provides current statistical data on the US uranium industry's activities relating to uranium raw materials and uranium marketing. It contains data for the period 1989 through 2008 as collected on the Form EIA-858, ''Uranium Industry Annual Survey.'' Data provides a comprehensive statistical characterization of the industry's activities for the survey year and also include some information about industry's plans and commitments for the near-term future. Data on uranium raw materials activities for 1989 through 1998, including exploration activities and expenditures, EIA-estimated reserves, mine production of uranium, production of uranium concentrate, and industry employment, are presented in Chapter 1. Data on uranium marketing activities for 1994 through 2008, including purchases of uranium and enrichment services, enrichment feed deliveries, uranium fuel assemblies, filled and unfilled market requirements, and uranium inventories, are shown in Chapter 2. The methodology used in the 1998 survey, including data edit and analysis, is described in Appendix A. The methodologies for estimation of resources and reserves are described in Appendix B. A list of respondents to the ''Uranium Industry Annual Survey'' is provided in Appendix C. The Form EIA-858 ''Uranium Industry Annual Survey'' is shown in Appendix D. For the readers convenience, metric versions of selected tables from Chapters 1 and 2 are presented in Appendix E along with the standard conversion factors used. A glossary of technical terms is at the end of the report. 24 figs., 56 tabs

Geochemical dispersion of uranium near prospects in Pennsylvania

International Nuclear Information System (INIS)

Rose, A.W.; Schmiermund, R.L.; Mahar, D.L.

1977-06-01

The geochemical dispersion of U was investigated near sedimentary uranium prospects in eastern and north-central Pennsylvania. Near Jim Thorpe, known uranium occurrences in the Catskill Fm. are limited to the base of the Duncannon member. At Penn Haven Junction, roll-type U deposits with appreciable Pb and Se are localized adjacent to an oxidized tongue of channel-filling conglomeratic sandstone. The channel and encircling U occurrences furnish a large target for geochemical exploration. Selective extractions show that the organic, Fe-oxide, sand and silt fractions of stream sediments are the major hosts for U in stream sediments. Fe-oxides have a greater affinity for U than organic matter but are less abundant. The U content of organic matter is about 10 5 times the U content of stream water. Stream sediments furnish a representative sample of the average content of U, Zn, Cu, and major elements in soils of a drainage basin in north-central Pennsylvania, so a semiquantitative appraisal of weathering uranium occurrences can be made from stream sediments in climates and topography like Pennsylvania. The flux of uranium leaving the basin in solution is about equal to that leaving as sediment. Uranium is considerably less mobile than Ca and Na. A new method of extracting uranium from water samples, using a liquid ion exchanger (Amberlite LA-1), shows promise for simple field application

Depleted and natural uranium: chemistry and toxicological effects.

Science.gov (United States)

Craft, Elena; Abu-Qare, Aquel; Flaherty, Meghan; Garofolo, Melissa; Rincavage, Heather; Abou-Donia, Mohamed

2004-01-01

Depleted uranium (DU) is a by-product from the chemical enrichment of naturally occurring uranium. Natural uranium is comprised of three radioactive isotopes: (238)U, (235)U, and (234)U. This enrichment process reduces the radioactivity of DU to roughly 30% of that of natural uranium. Nonmilitary uses of DU include counterweights in airplanes, shields against radiation in medical radiotherapy units and transport of radioactive isotopes. DU has also been used during wartime in heavy tank armor, armor-piercing bullets, and missiles, due to its desirable chemical properties coupled with its decreased radioactivity. DU weapons are used unreservedly by the armed forces. Chemically and toxicologically, DU behaves similarly to natural uranium metal. Although the effects of DU on human health are not easily discerned, they may be produced by both its chemical and radiological properties. DU can be toxic to many bodily systems, as presented in this review. Most importantly, normal functioning of the kidney, brain, liver, and heart can be affected by DU exposure. Numerous other systems can also be affected by DU exposure, and these are also reviewed. Despite the prevalence of DU usage in many applications, limited data exist regarding the toxicological consequences on human health. This review focuses on the chemistry, pharmacokinetics, and toxicological effects of depleted and natural uranium on several systems in the mammalian body. A section on risk assessment concludes the review.

Preparation of uranium-230 as a new uranium tracer

International Nuclear Information System (INIS)

Hashimoto, T.; Kido, K.; Sotobayashi, T.

1977-01-01

A uranium isotope, 230 U(T=20.8 d), was produced from the 231 Pa(γ,n) 230 Pa→viaβ - decay 230 U process with a bremsstrahlung irradiation on a protactinium target. After standing for about one month to obtain a maximal growth of 230 U, the uranium was chemically purified, applying an ion-exchange method. The purity of the 230 U obtained was examined with alpha spectrometry and an intrinsic alpha peak due to 230 U as a new uranium tracer in an alpha spectrometric analysis of uranium isotopes is described. (author)

Technical Basis For Radiological Acceptance Criteria For Uranium At The Y-12 National Security Complex

Energy Technology Data Exchange (ETDEWEB)

Veinot, K. G.

2009-07-22

The purpose of this report is to establish radiological acceptance criteria for uranium. Other factors for acceptance not considered include criticality safety concerns, contaminants to the process stream, and impacts to the Safety Basis for the affected facilities. Three types of criteria were developed in this report. They include limits on external penetrating and non-penetrating radiation and on the internal hazard associated with inhalation of the material. These criteria are intended to alleviate the need for any special controls beyond what are normally utilized for worker protection from uranium hazards. Any proposed exceptions would require case-by-case evaluations to determine cost impacts and feasibility. Since Y-12 has set rigorous ALARA goals for worker doses, the external limits are based on assumptions of work time involved in the movement of accepted material plus the desire that external doses normally received are not exceeded, and set so that no special personnel monitoring would be required. Internal hazard controls were established so that dose contributions from non-uranium nuclides would not exceed 10% of that expected from the uranium component. This was performed using a Hazard Index (HI) previously established for work in areas contaminated with non-uranium nuclides. The radiological acceptance criteria for uranium are summarized in Table 1. Note that these limits are based on the assumption that radioactive daughter products have reached equilibrium.

Synthesis of Uranium nitride powders using metal uranium powders

International Nuclear Information System (INIS)

Yang, Jae Ho; Kim, Dong Joo; Oh, Jang Soo; Rhee, Young Woo; Kim, Jong Hun; Kim, Keon Sik

2012-01-01

Uranium nitride (UN) is a potential fuel material for advanced nuclear reactors because of their high fuel density, high thermal conductivity, high melting temperature, and considerable breeding capability in LWRs. Uranium nitride powders can be fabricated by a carbothermic reduction of the oxide powders, or the nitriding of metal uranium. The carbothermic reduction has an advantage in the production of fine powders. However it has many drawbacks such as an inevitable engagement of impurities, process burden, and difficulties in reusing of expensive N 15 gas. Manufacturing concerns issued in the carbothermic reduction process can be solved by changing the starting materials from oxide powder to metals. However, in nitriding process of metal, it is difficult to obtain fine nitride powders because metal uranium is usually fabricated in the form of bulk ingots. In this study, a simple reaction method was tested to fabricate uranium nitride powders directly from uranium metal powders. We fabricated uranium metal spherical powder and flake using a centrifugal atomization method. The nitride powders were obtained by thermal treating those metal particles under nitrogen containing gas. We investigated the phase and morphology evolutions of powders during the nitriding process. A phase analysis of nitride powders was also a part of the present work

Estimation of uranium GI absorption fractions for children and adults

International Nuclear Information System (INIS)

Chen, J.; Lariviere, D.; Timmins, R.; Verdecchia, K.

2011-01-01

Uranium is ubiquitously found in drinking water and food. The gastrointestinal tract absorption fraction (f 1 ) is an important parameter in risk assessment of uranium burdens from ingestion. Although absorption of uranium from ingestion has been studied extensively in the past, human data concerning children and adults are still limited. In a previous study based on measurements of uranium concentration in 73 bone-ash samples collected by Health Canada, the absorption fractions for uranium ingestion were determined to be 0.093 ± 0.113 for infants, and 0.050 ± 0.032 for young children ranging from 1 to 7 y of age. To extend the study, a total of 69 bone-ash samples were selected for children and adults ranging from 7 to 25 y of age and residing in the same Canadian community that is known to have an elevated level of uranium in its drinking water supply. For each bone-ash sample, the total uranium concentration was measured by inductively coupled plasma mass spectrometry. To solve uranium transfer in the biokinetic model for uranium given in International Commission of Radiological Protection (ICRP) Publication 69 with estimated daily uranium intake, the program WinSAAM v3.0.1 was used. The absorption fractions were determined to be 0.030 ± 0.022 for children (7-18 y) and 0.021 ± 0.015 for adults (18-25 y). For anyone more than 18 y of age, the estimated f 1 value for uranium agree well with the ICRP recommended value of 0.02. Published by Oxford Univ. Press on behalf of the Canadian Government 2010. (authors)

Comparison of the Environment, Health, And Safety Characteristics of Advanced Thorium- Uranium and Uranium-Plutonium Fuel Cycles

Science.gov (United States)

Ault, Timothy M.

The environment, health, and safety properties of thorium-uranium-based (''thorium'') fuel cycles are estimated and compared to those of analogous uranium-plutonium-based (''uranium'') fuel cycle options. A structured assessment methodology for assessing and comparing fuel cycle is refined and applied to several reference fuel cycle options. Resource recovery as a measure of environmental sustainability for thorium is explored in depth in terms of resource availability, chemical processing requirements, and radiological impacts. A review of available experience and recent practices indicates that near-term thorium recovery will occur as a by-product of mining for other commodities, particularly titanium. The characterization of actively-mined global titanium, uranium, rare earth element, and iron deposits reveals that by-product thorium recovery would be sufficient to satisfy even the most intensive nuclear demand for thorium at least six times over. Chemical flowsheet analysis indicates that the consumption of strong acids and bases associated with thorium resource recovery is 3-4 times larger than for uranium recovery, with the comparison of other chemical types being less distinct. Radiologically, thorium recovery imparts about one order of magnitude larger of a collective occupational dose than uranium recovery. Moving to the entire fuel cycle, four fuel cycle options are compared: a limited-recycle (''modified-open'') uranium fuel cycle, a modified-open thorium fuel cycle, a full-recycle (''closed'') uranium fuel cycle, and a closed thorium fuel cycle. A combination of existing data and calculations using SCALE are used to develop material balances for the four fuel cycle options. The fuel cycle options are compared on the bases of resource sustainability, waste management (both low- and high-level waste, including used nuclear fuel), and occupational radiological impacts. At steady-state, occupational doses somewhat favor the closed thorium option while low

U.S. reference paper on the potential and limitations of uranium to meet the anticipated needs of nuclear energy

International Nuclear Information System (INIS)

1978-10-01

A framework is provided to analyze the interrelationship between uranium availability and the deployment of fast breeder and converter reactors. Included are models which can be used to estimate the uranium price for economic parity between breeders and converters, the dates for economical commercialization of fast breeders, and the effect of breeder deployment on uranium availability. Factors such as energy demand, resources and economics which are dominant in decisions as to potential breeder commercialization are discussed. Included are examples which show that breeder breakeven introduction date could fall between the year 2000 and well beyond 2025. A principal conclusion is that the break-even introduction date is very sensitive to uncertainty in the estimate of increase in capital costs of the breeder relative to the LWR, the estimates of power demand, and the estimate of the uranium resource base available at less than $130/kg (e.g. consideration of the IUREP estimates of speculative resources which if available doubles or triples the resource base)

The problem of radon in uranium mines; Le probleme du radon dans les mines d'uranium

Energy Technology Data Exchange (ETDEWEB)

Jammet, H; Pradel, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1955-07-01

The exploitation of uranium ores constitute the first stage in the use of the atomic energy. With the current methods of exploitation, we meet in these mines various dangers of irradiation and contamination which the presence of the radon constitutes one of the most important aspects. The supportable maximum concentration is currently of 10{sup -10} c of radon by liter of air. It seems, even while considering that the RaA, RaB and RaC descendants are not in balance, that it cannot be fix a less rigorous limit. Indeed the limit proposed by the ''Commission Internationale de Protection Radiologique'' give, for an exhibition of 40 hours per week a dose calculated to the level of the bronchi of: 9,5 rem/week with 100% of RaA and 50% of RaB and RaCs, or 19 rem/week with 100% of RaA, RaB and RaC instead of 0,3 rem. It is necessary, also, to take into account because of the risk is not unique for the miner who is expose to the radiation of ore and breath dusts of uranium. (authors) [French] L'exploitation des minerais d'uranium constitue le premier stade dans l'utilisation de l'energie atomique. Avec les methodes courantes d'exploitation on rencontre dans ces mines des dangers divers d'irradiation et de contamination dont la presence du radon constitue l'un des aspects les plus importants. La concentration maximum tolerable est actuellement de 10{sup -10} c de radon par litre d'air. Il semble, meme en considerant que les descendants RaA, RaB et RaC ne sont pas en equilibre, qu'on ne puisse pas fixer une limite moins rigoureuse. En effet la limite proposee par la Commission Internationale de Protection radiologique donne, pour une exposition de 40 heures par semaine une dose calculee au niveau des bronches de: 9,5 rem/semaine avec 100 % de RaA et 50 % de RaB et RaC, ou 19 rem/semaine avec 100 % de RaA, RaB et RaC au lieu de 0,3 rem. Il faut, en outre, tenir compte du fait que le risque n'est pas unique chez le mineur qui est expose au rayonnement du minerai et respire des

Transformations of highly enriched uranium into metal or oxide

International Nuclear Information System (INIS)

Nollet, P.; Sarrat, P.

1964-01-01

The enriched uranium workshops in Cadarache have a double purpose on the one hand to convert uranium hexafluoride into metal or oxide, and on the other hand to recover the uranium contained in scrap materials produced in the different metallurgical transformations. The principles that have been adopted for the design and safety of these workshops are reported. The nuclear safety is based on the geometrical limitations of the processing vessels. To establish the processes and the technology of these workshops, many studies have been made since 1960, some of which have led to original achievements. The uranium hexafluoride of high isotopic enrichment is converted either by injection of the gas into ammonia or by an original process of direct hydrogen reduction to uranium tetrafluoride. The uranium contained m uranium-zirconium metal scrap can be recovered by combustion with hydrogen chloride followed treatment of the uranium chloride by fluorine in order to obtain the uranium in the hexafluoride state. Recovery of the uranium contained m various scrap materials is obtained by a conventional refining process combustion of metallic scrap, nitric acid dissolution of the oxide, solvent purification by tributyl phosphate, ammonium diuranate precipitation, calcining, reduction and hydro fluorination into uranium tetrafluoride, bomb reduction by calcium and slag treatment. Two separate workshops operate along these lines one takes care of the uranium with an isotopic enrichment of up to 3 p. 100, the other handles the high enrichments. The handling of each step of this process, bearing in mind the necessity for nuclear safety, has raised some special technological problems and has led to the conception of new apparatus, in particular the roasting furnace for metal turnings, the nitric acid dissolution unit, the continuous precipitator and ever safe filter and dryer for ammonium diuranate, the reduction and hydro fluorination furnace and the slag recovery apparatus These are

Uranium market

International Nuclear Information System (INIS)

Rubini, L.A.; Asem, M.A.D.

1990-01-01

The historical development of the uranium market is present in two periods: The initial period 1947-1970 and from 1970 onwards, with the establishment of a commercial market. The world uranium requirements are derived from the corresponding forecast of nuclear generating capacity, with, particular emphasis to the brazilian requirements. The forecast of uranium production until the year 2000 is presented considering existing inventories and the already committed demand. The balance between production and requirements is analysed. Finally the types of contracts currently being used and the development of uranium prices in the world market are considered. (author)

Innovative Elution Processes for Recovering Uranium from Seawater

International Nuclear Information System (INIS)

Wai, Chien; Tian, Guoxin; Janke, Christopher

2014-01-01

Utilizing amidoxime-based polymer sorbents for extraction of uranium from seawater has attracted considerable interest in recent years. Uranium collected in the sorbent is recovered typically by elution with an acid. One drawback of acid elution is deterioration of the sorbent which is a significant factor that limits the economic competitiveness of the amidoxime-based sorbent systems for sequestering uranium from seawater. Developing innovative elution processes to improve efficiency and to minimize loss of sorbent capacity become essential in order to make this technology economically feasible for large-scale industrial applications. This project has evaluated several elution processes including acid elution, carbonate elution, and supercritical fluid elution for recovering uranium from amidoxime-based polymer sorbents. The elution efficiency, durability and sorbent regeneration for repeated uranium adsorption- desorption cycles in simulated seawater have been studied. Spectroscopic techniques are used to evaluate chemical nature of the sorbent before and after elution. A sodium carbonate-hydrogen peroxide elution process for effective removal of uranium from amidoxime-based sorbent is developed. The cause of this sodium carbonate and hydrogen peroxide synergistic leaching of uranium from amidoxime-based sorbent is attributed to the formation of an extremely stable uranyl peroxo-carbonato complex. The efficiency of uranium elution by the carbonate-hydrogen peroxide method is comparable to that of the hydrochloric acid elution but damage to the sorbent material is much less for the former. The carbonate- hydrogen peroxide elution also does not need any elaborate step to regenerate the sorbent as those required for hydrochloric acid leaching. Several CO2-soluble ligands have been tested for extraction of uranium from the sorbent in supercritical fluid carbon dioxide. A mixture of hexafluoroacetylacetone and tri-n-butylphosphate shows the best result but uranium

Innovative Elution Processes for Recovering Uranium from Seawater

Energy Technology Data Exchange (ETDEWEB)

Wai, Chien [Univ. of Idaho, Moscow, ID (United States); Tian, Guoxin [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Janke, Christopher [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2014-05-29

Utilizing amidoxime-based polymer sorbents for extraction of uranium from seawater has attracted considerable interest in recent years. Uranium collected in the sorbent is recovered typically by elution with an acid. One drawback of acid elution is deterioration of the sorbent which is a significant factor that limits the economic competitiveness of the amidoxime-based sorbent systems for sequestering uranium from seawater. Developing innovative elution processes to improve efficiency and to minimize loss of sorbent capacity become essential in order to make this technology economically feasible for large-scale industrial applications. This project has evaluated several elution processes including acid elution, carbonate elution, and supercritical fluid elution for recovering uranium from amidoxime-based polymer sorbents. The elution efficiency, durability and sorbent regeneration for repeated uranium adsorption- desorption cycles in simulated seawater have been studied. Spectroscopic techniques are used to evaluate chemical nature of the sorbent before and after elution. A sodium carbonate-hydrogen peroxide elution process for effective removal of uranium from amidoxime-based sorbent is developed. The cause of this sodium carbonate and hydrogen peroxide synergistic leaching of uranium from amidoxime-based sorbent is attributed to the formation of an extremely stable uranyl peroxo-carbonato complex. The efficiency of uranium elution by the carbonate-hydrogen peroxide method is comparable to that of the hydrochloric acid elution but damage to the sorbent material is much less for the former. The carbonate- hydrogen peroxide elution also does not need any elaborate step to regenerate the sorbent as those required for hydrochloric acid leaching. Several CO2-soluble ligands have been tested for extraction of uranium from the sorbent in supercritical fluid carbon dioxide. A mixture of hexafluoroacetylacetone and tri-n-butylphosphate shows the best result but uranium

Comparison of numerical and physico-chemical models for on-line spectrophotometric control of uranium

International Nuclear Information System (INIS)

Corriou, J.P.; Boisde, G.

1986-04-01

In view of on-line spectrophotometric control of fuel reprocessing streams, a physico-chemical model able to predict uranium and nitric acid concentrations in an uranyl nitrate-nitric acid system has been searched. Thus the influences of the following parameters: uranium, nitrate, hydrogen ion concentrations, ionic strength, on the equilibria of complexation of uranium (VI) nitrate have been evaluated. Extinction coefficients for the uranium mononitrate and uranium dinitrate complexes are given between 410 and 440 nm. The apparent equilibrium constants are determined as a function of the ionic strength. The limitations of this predictive model are emphasized and comparisons with numerical models are discussed. (16 refs)

Study of uranium matrix interference on ten analytes using inductively coupled plasma atomic emission spectrometry

Energy Technology Data Exchange (ETDEWEB)

Ghazi, A.A.; Qamar, S.; Atta, M.A. (A.Q. Khan Research Labs., Rawalpindi (Pakistan))

1993-08-01

Maximum allowable concentrations of 12 elements in uranium hexafluoride feed for enrichment to reactor grade material (about 3%), vary from 1 to 100 ppm ([mu]g/g). Using an inductively coupled plasma atomic emission spectrometer, 51 lines of tine of these elements (B, Cr, Mo, P, Sb, Si, Ta, Ti, V and W) has been studied with a uranium matrix to investigate the matrix interference on the basis of signal to background (SBR), and background to background ratios (BBR). Detection limits and limits of quantitative determination (LQDs) were calculated for these elements in a uranium matrix using SBR and relative standard deviation of the background signal (RSD[sub B]) approach. In almost all cases, the uranium matrix interference reduces the SBRs to the extent that direct trace analysis is impossible. A uranium sample having known concentrations of impurities (around LQDs) was directly analysed with results that showed reasonable accuracy and precision. (Author).

Electrochemistry of uranium in sodium chloroaluminate melts

International Nuclear Information System (INIS)

D'olieslager, W.; Meuris, F.; Heerman, L.

1990-01-01

The electrochemical behaviour of uranium was studied in basic, NaCl-saturated NaAlCl 4 melts at 175 deg C. Solutions of UO 3 exhibit two oxidation/reduction waves (cyclic voltammetry). Analysis of the peak currents (cyclic voltammetry), the limiting currents (pulse polarography) and the non-linear log i-t curves (anodic controlled potential coulometry) leads to the conclusion that uranium(IV) in the basic chloroaluminate melt exists as two different species in slow equilibrium with one another, of which only one species can be oxidized to U(VI). (author) 16 refs.; 7 figs.; 3 tabs

Uranium

International Nuclear Information System (INIS)

Whillans, R.T.

1981-01-01

Events in the Canadian uranium industry during 1980 are reviewed. Mine and mill expansions and exploration activity are described, as well as changes in governmental policy. Although demand for uranium is weak at the moment, the industry feels optimistic about the future. (LL)

Uranium industry annual 1985

International Nuclear Information System (INIS)

1986-11-01

This report consists of two major sections. The first addresses uranium raw materials activities and covers the following topics: exploration activities and expenditures, resources and reserves, mine production of uranium, production of uranium concentrate, and industry employment. The second major section is concerned with the following uranium marketing activities: uranium purchase commitments, uranium prices, procurement arrangements, uranium imports and exports, enrichment services, inventories, secondary market activities, utility market requirements, and related topics. A glossary and appendices are included to assist the reader in interpreting the substantial array of statistical data in this report and to provide background information about the survey

Uranium

Energy Technology Data Exchange (ETDEWEB)

Williams, R M

1976-01-01

Evidence of expanding markets, improved prices and the short supply of uranium became abundantly clear in 1975, providing the much needed impetus for widespread activity in all phases of uranium operations. Exploration activity that had been at low levels in recent years in Canada was evident in most provinces as well as the Northwest Territories. All producers were in the process of expanding their uranium-producing facilities. Canada's Atomic Energy Control Board (AECB) by year-end had authorized the export of over 73,000 tons of U/sub 3/0/sub 8/ all since September 1974, when the federal government announced its new uranium export guidelines. World production, which had been in the order of 25,000 tons of U/sub 3/0/sub 8/ annually, was expected to reach about 28,000 tons in 1975, principally from increased output in the United States.

Uranium Concentration of Contaminated Zone due to the Cover Depth for Self-Disposal

International Nuclear Information System (INIS)

Koo, Dae Seo; Sung, Hyun Hee; Kim, Gye Nam; Kim, Seung Soo; Kim, Il Gook; Han, Gyu Seong; Choi, Jong Won

2016-01-01

To acquire radiation dose under self disposal from them, the study on decontamination of some uranium contaminated soil and concrete wastes was performed using electrokinetic-electrodialytic. In this study, we evaluated radiation dose due to cover depth on contaminated zone such as uranium contaminated soil and concrete wastes under radiation dose limit using RESRAD Version 6.5. At first, the calculation of the radiation dose on the contaminated zone are carried out. The second, the uranium concentration of contaminated zone due to the cover depth are also analyzed. The uranium contaminated soil and concrete wastes under radiation dose limit by decontaminating them have application to self-disposal of contaminated zone. The area of contaminated zone is 1,500 m"2. The thickness of contaminated zone is 2 m. The length parallel to aquifer flow is 43.702m. The age of the residents on contaminated zone is 15 years old. The period of evaluation on the contaminated zone is from regulation exemption of uranium contaminated soil and concrete wastes till 1,000 years. The calculation of the radiation dose on contaminated zone are carried out. The uranium concentration of contaminated zone due to the cover depth was also analyzed. as the cover depth increases, the uranium concentration has an increasing trend. As the cover depth increases, radiation dose of a person has a decreasing trend. As the cover depth increases, the radiation dose of residents has also a decreasing trend.

Uranium Concentration of Contaminated Zone due to the Cover Depth for Self-Disposal

Energy Technology Data Exchange (ETDEWEB)

Koo, Dae Seo; Sung, Hyun Hee; Kim, Gye Nam; Kim, Seung Soo; Kim, Il Gook; Han, Gyu Seong; Choi, Jong Won [KAERI, Daejeon (Korea, Republic of)

2016-05-15

To acquire radiation dose under self disposal from them, the study on decontamination of some uranium contaminated soil and concrete wastes was performed using electrokinetic-electrodialytic. In this study, we evaluated radiation dose due to cover depth on contaminated zone such as uranium contaminated soil and concrete wastes under radiation dose limit using RESRAD Version 6.5. At first, the calculation of the radiation dose on the contaminated zone are carried out. The second, the uranium concentration of contaminated zone due to the cover depth are also analyzed. The uranium contaminated soil and concrete wastes under radiation dose limit by decontaminating them have application to self-disposal of contaminated zone. The area of contaminated zone is 1,500 m{sup 2}. The thickness of contaminated zone is 2 m. The length parallel to aquifer flow is 43.702m. The age of the residents on contaminated zone is 15 years old. The period of evaluation on the contaminated zone is from regulation exemption of uranium contaminated soil and concrete wastes till 1,000 years. The calculation of the radiation dose on contaminated zone are carried out. The uranium concentration of contaminated zone due to the cover depth was also analyzed. as the cover depth increases, the uranium concentration has an increasing trend. As the cover depth increases, radiation dose of a person has a decreasing trend. As the cover depth increases, the radiation dose of residents has also a decreasing trend.

Uptake of uranium from underground drinking water by chlorella (Chlorella pyrendoidosa)

International Nuclear Information System (INIS)

Singhal, R.K.; Joshi, Shobha; Gurg, R.P.; Shenoy, N.S.; Ferandes, Neychelle; Gopale, Rajesh S.; Jhaveri, A.S.

2002-01-01

Naturally occurring uranium has found at elevated levels i.e. 300-1200 ppb in underground water, especially in the areas located around uranium mines and granite rocks sites. The U.S. Environmental Protection Agency (EPA) recently adopted drinking water standards requiring a maximum uranium concentration of 20 μgl. This limit is based on nephro-toxicity, rather than on radiological hazards. The concentration of uranium is to be monitored along with other parameters in well and other sources of drinking water in these areas. During this work a low cost kit was developed for removing uranium from under-ground water used for drinking purposes. This unit is capable of reducing uranium from 1000 ppb to 15-20 ppb. Chlorella (Chlorella pyrendoidosa), a fresh water algae, was immobilised in sodium alginate in the form of beads by using 0.2 M calcium chloride. These beads were put in container and the water is stirred occasionally. 99-100 % uranium adsorbed was recovered from the beads by using 0.1 M HNO 3 . These results suggest that the uptake of uranium by Chlorella depended upon the physico-chemical adsorption on the cell surface, but not upon the biological activity and that uranium in the algal cells was coupled with the ligands, which can be easily substituted with NO 3 -1 . (author)

The uranium enrichment industry and the SILEX process

International Nuclear Information System (INIS)

Goldsworthy, M.

1999-01-01

Silex Systems Limited has been developing a new laser isotope separation process since 1992. The principle application of the SILEX Technology is Uranium Enrichment, the key step in the production of fuel for nuclear power plants. The Uranium Enrichment industry, today worth ∼ US$3.5 Billion p.a., is dominated by four major players, the largest being USEC with almost 40% of the market. In 1996, an agreement was signed between Silex and USEC to develop SILEX Technology for potential application to Uranium Enrichment. The SILEX process is a low cost, energy efficient scheme which may provide significant commercial advantage over current technology and competing laser processes. Silex is also investigating possible application to the enrichment of Silicon, Carbon and other materials. Significant markets may develop for such materials, particularly in the semiconductor industry

Chapter 1. General information about uranium. 1.3. Uranium ores

International Nuclear Information System (INIS)

Khakimov, N.; Nazarov, Kh.M.; Mirsaidov, I.U.

2012-01-01

The uranium ores were described. It was found that uranium ores and natural mineral formations containing uranium and its compounds, can be found in concentrations that are technically possible for industrial utilization and which are economically profitable. It was defined that oxidation levels of uranium minerals have an impact on their reprocessing technology and behavior in hydrometallurgical re partition. It was found that the chemical composition of ores has a decisive importance during selection of their reprocessing method.

Redox behaviour of uranium with iron compounds

International Nuclear Information System (INIS)

Ithurbide, A.

2009-10-01

An option investigated for the management of long-term nuclear waste is a repository in deep geological formations. It is generally admitted that the release of radionuclides from the spent fuel in the geosphere could occur several thousand years after the beginning of the storage. Therefore, to assess the safety of the long-term disposal, it is important to consider the phenomena that can reduce the migration, and in particular the migration of uranium. The aim of this work is to study if siderite, an iron compound present both in the near - and far -field, can limit this migration as well as the role played by the redox process. Siderite thin layers have been obtained by electrochemistry. The layers are adherent and homogeneous. Their thickness is about 1 μm and they are composed of spherical grains. Analytical characterizations performed show that siderite is free of any impurity and does not exhibit any trace of oxidation. The interactions between siderite and uranium (VI) have been carried out in solutions considered as representative of environmental waters, in terms of pH and carbonate concentration. The retention of uranium on the thin layer is important since, after 24 hours of interaction, it corresponds to retention capacities of several hundreds of uranium micro-moles per gram of siderite. XPS analysis show that, in any studied condition, part of uranium present on the thin layer is reduced into an over stoichiometric uranium dioxide. The process of interaction differs depending on the considered environment, specially on the stability of siderite. (author)

Derived enriched uranium market

International Nuclear Information System (INIS)

Rutkowski, E.

1996-01-01

The potential impact on the uranium market of highly enriched uranium from nuclear weapons dismantling in the Russian Federation and the USA is analyzed. Uranium supply, conversion, and enrichment factors are outlined for each country; inventories are also listed. The enrichment component and conversion components are expected to cause little disruption to uranium markets. The uranium component of Russian derived enriched uranium hexafluoride is unresolved; US legislation places constraints on its introduction into the US market

Equations of state for enriched uranium and uranium alloy to 3500 MPa

International Nuclear Information System (INIS)

Bai Chaomao; Hai Yuying; Liu Jenlong; Li Zhenrong

1990-04-01

The volume compressions of 6 kinds of cast materials including enriched uranium, poor uranium, U-0.57 wt% Ti, U-0.33 wt% Nb, U-2.85 wt% Nb and U-7.5 wt% Nb-3.3 wt% Zr have been determined by monitoring piston displacements in a piston cylinder apparatus with double strengthening rings to 3500 MPa at room temperature. The dilation of the cylinder vessel and the press deformation were corrected by some experiments. The calculational data free from using the standard sample closed with used standard sample. The volume compressions of enriched uranium and poor uranium are nearly coincident. Pure uranium is more compressible than uranium alloys. These values of enriched uranium are in close agreement with values of Bridgman's pure uranium. The fitting coefficients of Bridgman's polynomial and Anderson's equation of state and isothermal bulk modules for the above materials are given

Preliminary developments of MTR plates with uranium nitride

Energy Technology Data Exchange (ETDEWEB)

Durand, J.P.; Laudamy, P. [CERCA, Romans (France); Richter, K. [Institut fuer Transurane, Karlsruhe (Germany)

1997-08-01

In the opinion of CERCA, the total weight of Uranium per MTR plate (without changing the external dimensions) cannot be further increased using U{sub 3}Si{sub 2}. Limits have been reached on plates with a thicker meat or loaded to 6g Ut/cm{sup 3}. The use of a denser fuel like Uranium mononitride could permit an increase in these limits. A collaboration between the Institute for Transuranium Elements (ITU), Joint Research Centre of the European Commission, and CERCA has been set ut. The preliminary studies at the ITU to check compatibility between aluminium and UN proved that there are no metallurgical interactions below 500{degrees}C. Feasibility of the manufacturing, on a laboratory scale at CERCA, of depleted Uranium mononitride plates loaded to 7 g Ut/cm{sup 3} has been demonstrated. The manufacturing process, however, is only one aspect of the development of a new fuel. The experience gained in the case of U{sub 3}Si{sub 2} has shown that the development of a new fuel requires considerable time and financial investment. Such a development certainly represents an effort of about 10 years.

Preliminary developments of MTR plates with uranium nitride

International Nuclear Information System (INIS)

Durand, J.P.; Laudamy, P.; Richter, K.

1997-01-01

In the opinion of CERCA, the total weight of Uranium per MTR plate (without changing the external dimensions) cannot be further increased using U 3 Si 2 . Limits have been reached on plates with a thicker meat or loaded to 6g Ut/cm 3 . The use of a denser fuel like Uranium mononitride could permit an increase in these limits. A collaboration between the Institute for Transuranium Elements (ITU), Joint Research Centre of the European Commission, and CERCA has been set ut. The preliminary studies at the ITU to check compatibility between aluminium and UN proved that there are no metallurgical interactions below 500 degrees C. Feasibility of the manufacturing, on a laboratory scale at CERCA, of depleted Uranium mononitride plates loaded to 7 g Ut/cm 3 has been demonstrated. The manufacturing process, however, is only one aspect of the development of a new fuel. The experience gained in the case of U 3 Si 2 has shown that the development of a new fuel requires considerable time and financial investment. Such a development certainly represents an effort of about 10 years

IAEA Activities on Uranium Resources and Production, and Databases for the Nuclear Fuel Cycle

Energy Technology Data Exchange (ETDEWEB)

Ganguly, C.; Slezak, J. [Divison of Nuclear Fuel Cycle and Waste Technology, International Atomic Energy Agency, Vienna (Austria)

2014-05-15

In recent years rising expectation for nuclear power has led to a significant increase in the demand for uranium and in turn dramatic increases in uranium exploration, mining and ore processing activities worldwide. Several new countries, often with limited experience, have also embarked on these activities. The ultimate goal of the uranium raw material industry is to provide an adequate supply of uranium that can be delivered to the market place at a competitive price by environmentally sound, mining and milling practices. The IAEA’s programme on uranium raw material encompass all aspects of uranium geology and deposits, exploration, resources, supply and demand, uranium mining and ore processing, environmental issues in the uranium production cycle and databases for the uranium fuel cycle. Radiological safety and environmental protection are major challenges in uranium mines and mills and their remediation. The IAEA has revived its programme for the Uranium Production Site Appraisal Team (UPSAT) to assist Member States to improve operational and safety performances at uranium mines and mill sites. The present paper summarizes the ongoing activities of IAEA on uranium raw material, highlighting the status of global uranium resources, their supply and demand, the IAEA database on world uranium deposit (UDEPO) and nuclear fuel cycle information system (NFCIS), recent IAEA Technical Meetings (TM) and related ongoing Technical Cooperation (TC) projects. (author)

Uranium in Canada

International Nuclear Information System (INIS)

1985-09-01

In 1974 the Minister of Energy, Mines and Resources (EMR) established a Uranium Resource Appraisal Group (URAG) within EMR to audit annually Canada's uranium resources for the purpose of implementing the federal government's uranium export policy. A major objective of this policy was to ensure that Canadian uranium supplies would be sufficient to meet the needs of Canada's nuclear power program. As projections of installed nuclear power growth in Canada over the long term have been successively revised downwards (the concern about domestic security of supply is less relevant now than it was 10 years ago) and as Canadian uranium supply capabilities have expanded significantly. Canada has maintained its status as the western world's leading exporter of uranium and has become the world's leading producer. Domestic uranium resource estimates have increased to 551 000 tonnes U recoverable from mineable ore since URAG completed its last formal assessment (1982). In 1984, Canada's five primary uranium producers employed some 5800 people at their mining and milling operations, and produced concentrates containing some 11 170 tU. It is evident from URAG's 1984 assessment that Canada's known uranium resources, recoverable at uranium prices of $150/kg U or less, are more than sufficient to meet the 30-year fuelling requirements of those reactors that are either in opertaion now or committed or expected to be in-service by 1995. A substantial portion of Canada's identified uranium resources, recoverable within the same price range, is thus surplus to Canadian needs and available for export. Sales worth close to $1 billion annually are assured. Uranium exploration expenditures in Canada in 1983 and 1984 were an estimated $41 million and $35 million, respectively, down markedly from the $128 million reported for 1980. Exploration drilling and surface development drilling in 1983 and 1984 were reported to be 153 000 m and 197 000 m, respectively, some 85% of which was in

Research on deeply purifying effluent from uranium mining and metallurgy to remove uranium by ion exchange. Pt.2: Elution uranium from lower loaded uranium resin by the intense fractionation process

International Nuclear Information System (INIS)

Zhang Jianguo; Chen Shaoqiang; Qi Jing

2002-01-01

Developing macroporous resin for purifying uranium effluent from uranium mining and metallurgy is presented. The Intense Fractionation Process is employed to elute uranium from lower loaded uranium resin by the eluent of sulfuric acid and ammonium sulfate. The result is indicated that the uranium concentration in the rich elutriant is greatly increased, and the rich liquor is only one bed column volume, uranium concentration in the elutriant is increased two times which concentration is 10.1 g/L. The eluent is saved about 50% compared with the conventional fixed bed elution operation. And also the acidity in the rich elutriant is of benefit to the later precipitation process in uranium recovery

Recycling of reprocessed uranium

International Nuclear Information System (INIS)

Randl, R.P.

1987-01-01

Since nuclear power was first exploited in the Federal Republic of Germany, the philosophy underlying the strategy of the nuclear fuel cycle has been to make optimum use of the resource potential of recovered uranium and plutonium within a closed fuel cycle. Apart from the weighty argument of reprocessing being an important step in the treatment and disposal of radioactive wastes, permitting their optimum ecological conditioning after the reprocessing step and subsequent storage underground, another argument that, no doubt, carried weight was the possibility of reducing the demand of power plants for natural uranium. In recent years, strategies of recycling have emerged for reprocessed uranium. If that energy potential, too, is to be exploited by thermal recycling, it is appropriate to choose a slightly different method of recycling from the one for plutonium. While the first generation of reprocessed uranium fuel recycled in the reactor cuts down natural uranium requirement by some 15%, the recycling of a second generation of reprocessed, once more enriched uranium fuel helps only to save a further three per cent of natural uranium. Uranium of the second generation already carries uranium-232 isotope, causing production disturbances, and uranium-236 isotope, causing disturbances of the neutron balance in the reactor, in such amounts as to make further fabrication of uranium fuel elements inexpedient, even after mixing with natural uranium feed. (orig./UA) [de

Challenges dealing with depleted uranium in Germany - Reuse or disposal

International Nuclear Information System (INIS)

Moeller, Kai D.

2007-01-01

During enrichment large amounts of depleted Uranium are produced. In Germany every year 2.800 tons of depleted uranium are generated. In Germany depleted uranium is not classified as radioactive waste but a resource for further enrichment. Therefore since 1996 depleted Uranium is sent to ROSATOM in Russia. However it still has to be dealt with the second generation of depleted Uranium. To evaluate the alternative actions in case a solution has to be found in Germany, several studies have been initiated by the Federal Ministry of the Environment. The work that has been carried out evaluated various possibilities to deal with depleted uranium. The international studies on this field and the situation in Germany have been analyzed. In case no further enrichment is planned the depleted uranium has to be stored. In the enrichment process UF 6 is generated. It is an international consensus that for storage it should be converted to U 3 O 8 . The necessary technique is well established. If the depleted Uranium would have to be characterized as radioactive waste, a final disposal would become necessary. For the planned Konrad repository - a repository for non heat generating radioactive waste - the amount of Uranium is limited by the licensing authority. The existing license would not allow the final disposal of large amounts of depleted Uranium in the Konrad repository. The potential effect on the safety case has not been roughly analyzed. As a result it may be necessary to think about alternatives. Several possibilities for the use of depleted uranium in the industry have been identified. Studies indicate that the properties of Uranium would make it useful in some industrial fields. Nevertheless many practical and legal questions are open. One further option may be the use as shielding e.g. in casks for transport or disposal. Possible techniques for using depleted Uranium as shielding are the use of the metallic Uranium as well as the inclusion in concrete. Another

SRTC criticality technical review: Nuclear Criticality Safety Evaluation 93-18 Uranium Solidification Facility's Waste Handling Facility

International Nuclear Information System (INIS)

Rathbun, R.

1993-01-01

Separate review of NMP-NCS-930058, open-quotes Nuclear Criticality Safety Evaluation 93-18 Uranium Solidification Facility's Waste Handling Facility (U), August 17, 1993,close quotes was requested of SRTC Applied Physics Group. The NCSE is a criticality assessment to determine waste container uranium limits in the Uranium Solidification Facility's Waste Handling Facility. The NCSE under review concludes that the NDA room remains in a critically safe configuration for all normal and single credible abnormal conditions. The ability to make this conclusion is highly dependent on array limitation and inclusion of physical barriers between 2x2x1 arrays of boxes containing materials contaminated with uranium. After a thorough review of the NCSE and independent calculations, this reviewer agrees with that conclusion

How much uranium

International Nuclear Information System (INIS)

Kenward, M.

1976-01-01

Comment is made on the latest of a series of reports on world uranium resources from the OECD's Nuclear Energy Agency and the UN's International Atomic Energy Agency (Uranium resources, production and demand (including other nuclear fuel cycle data), published by the Organisation for Economic Cooperation and Development, Paris). The report categories uranium reserves by their recovery cost and looks at power demand and the whole of the nuclear fuel cycle, including uranium enrichment and spent fuel reprocessing. The effect that fluctuations in uranium prices have had on exploration for new uranium resources is considered. It is stated that increased exploration is essential considering the long lead times involved but that thanks to today's higher prices there are distinct signs that prospecting activities are increasing again. (U.K.)

Determination of uranium by luminescent method (tablet variant)

International Nuclear Information System (INIS)

Sergeev, A.N.; Yufa, B.Ya.

1985-01-01

A new tablet variant of luminescent determination of uranium in rocks is developed. The analytical process includes the following operations: sample decomposition, uranium separation from luminescence quencher impurities, preparation of luminescent sample (tablet), photometry of the tablet. The method has two variants developed: the first one is characterized by a more hard decomposition, sample mass being 0.2 g; the second variant has a better detection limit (5x10 -6 %), the sample mass being 0.2-1 g. Procedures of the sample preparation for both variants of analysis are described

International Uranium Resources Evaluation Project (IUREP) orientation phase mission summary report: Cameroon

International Nuclear Information System (INIS)

1985-01-01

A report has recently been published which describes the findings of the International Uranium Resources Evaluation Project (IUREP) Mission to Cameroon. The IUREP Orientation Phase Mission to Cameroon estimates the Speculative Resources of that country to be in the order of 10 000 tonnes uranium for syenite-associated U-deposits in southern Cameroon, and in the order of 5 000 tonnes uranium for uranium deposits associated with albitized and desilicified late tectonic Panafrican granites (episyenite) and Paleozoic volcanics in northern Cameroon. No specific tonnage is given for Francevillian equivalents (DJA-Series) and for Mesozoic and Cenozoic sedimentary basins, which are thought to hold limited potential for sandstone hosted uranium. However the Douala basin, consisting of mixed marine and continental sequences merits some attention. No specific budget and programme for uranium exploration are proposed for Cameroon. Instead specific recommendations concerning specific potential environments and general recommendation concerning the methodology of exploration are made. (author)

Evaluating the effectiveness of dilution of the recovered uranium with depleted uranium and low-enriched uranium to obtain fuel for VVER reactors

International Nuclear Information System (INIS)

Smirnov, A Yu; Sulaberidze, G A; Dudnikov, A A; Nevinitsa, V A

2016-01-01

The possibility of the recovered uranium enrichment in a cascade of gas centrifuges with three feed flows (depleted uranium, low-enriched uranium, recovered uranium) with simultaneous dilution of U-232,234,236 isotopes was shown. A series of numerical experiments were performed for different content of U-235 in low-enriched uranium. It has been demonstrated that the selected combination of diluents can simultaneously reduce the cost of separative work and the consumption of natural uranium, not only with respect to the previously used multi-flow cascade schemes, but also in comparison to the standard cascade for uranium enrichment. (paper)

Development of Novel Sorbents for Uranium Extraction from Seawater

Energy Technology Data Exchange (ETDEWEB)

Lin, Wenbin [Univ. of Chicago, IL (United States); Taylor-Pashow, Kathryn [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2014-01-08

As the uranium resource in terrestrial ores is limited, it is difficult to ensure a long-term sustainable nuclear energy technology. The oceans contain approximately 4.5 billion tons of uranium, which is one thousand times the amount of uranium in terrestrial ores. Development of technologies to recover the uranium from seawater would greatly improve the uranium resource availability, sustaining the fuel supply for nuclear energy. Several methods have been previously evaluated including solvent extraction, ion exchange, flotation, biomass collection, and adsorption; however, none have been found to be suitable for reasons such as cost effectiveness, long term stability, and selectivity. Recent research has focused on the amidoxime functional group as a promising candidate for uranium sorption. Polymer beads and fibers have been functionalized with amidoxime functional groups, and uranium adsorption capacities as high as 1.5 g U/kg adsorbent have recently been reported with these types of materials. As uranium concentration in seawater is only ~3 ppb, great improvements to uranium collection systems must be made in order to make uranium extraction from seawater economically feasible. This proposed research intends to develop transformative technologies for economic uranium extraction from seawater. The Lin group will design advanced porous supports by taking advantage of recent breakthroughs in nanoscience and nanotechnology and incorporate high densities of well-designed chelators into such nanoporous supports to allow selective and efficient binding of uranyl ions from seawater. Several classes of nanoporous materials, including mesoporous silica nanoparticles (MSNs), mesoporous carbon nanoparticles (MCNs), meta-organic frameworks (MOFs), and covalent-organic frameworks (COFs), will be synthesized. Selective uranium-binding liagnds such as amidoxime will be incorporated into the nanoporous materials to afford a new generation of sorbent materials that will be

Development of Novel Sorbents for Uranium Extraction from Seawater

International Nuclear Information System (INIS)

Lin, Wenbin; Taylor-Pashow, Kathryn

2014-01-01

As the uranium resource in terrestrial ores is limited, it is difficult to ensure a long-term sustainable nuclear energy technology. The oceans contain approximately 4.5 billion tons of uranium, which is one thousand times the amount of uranium in terrestrial ores. Development of technologies to recover the uranium from seawater would greatly improve the uranium resource availability, sustaining the fuel supply for nuclear energy. Several methods have been previously evaluated including solvent extraction, ion exchange, flotation, biomass collection, and adsorption; however, none have been found to be suitable for reasons such as cost effectiveness, long term stability, and selectivity. Recent research has focused on the amidoxime functional group as a promising candidate for uranium sorption. Polymer beads and fibers have been functionalized with amidoxime functional groups, and uranium adsorption capacities as high as 1.5 g U/kg adsorbent have recently been reported with these types of materials. As uranium concentration in seawater is only ~3 ppb, great improvements to uranium collection systems must be made in order to make uranium extraction from seawater economically feasible. This proposed research intends to develop transformative technologies for economic uranium extraction from seawater. The Lin group will design advanced porous supports by taking advantage of recent breakthroughs in nanoscience and nanotechnology and incorporate high densities of well-designed chelators into such nanoporous supports to allow selective and efficient binding of uranyl ions from seawater. Several classes of nanoporous materials, including mesoporous silica nanoparticles (MSNs), mesoporous carbon nanoparticles (MCNs), meta-organic frameworks (MOFs), and covalent-organic frameworks (COFs), will be synthesized. Selective uranium-binding liagnds such as amidoxime will be incorporated into the nanoporous materials to afford a new generation of sorbent materials that will be

Uranium

International Nuclear Information System (INIS)

Anon.

1983-01-01

Recent decisions by the Australian Government will ensure a significant expansion of the uranium industry. Development at Roxby Downs may proceed and Ranger may fulfil two new contracts but the decision specifies that apart from Roxby Downs, no new mines should be approved. The ACTU maintains an anti-uranium policy but reaction to the decision from the trade union movement has been muted. The Australian Science and Technology Council (ASTEC) has been asked by the Government to conduct an inquiry into a number of issues relating to Australia's role in the nuclear fuel cycle. The inquiry will examine in particular Australia's nuclear safeguards arrangements and the adequacy of existing waste management technology. In two additional decisions the Government has dissociated itself from a study into the feasibility of establishing an enrichment operation and has abolished the Uranium Advisory Council. Although Australian reserves account for 20% of the total in the Western World, Australia accounts for a relatively minor proportion of the world's uranium production

International Uranium Resources Evaluation Project (IUREP) national favourability studies: Belgium

International Nuclear Information System (INIS)

1977-12-01

Uranium occurrences and resources - To date the uranium identified in Belgium is limited to a number of occurrences and none of these have as yet proved significant from a reserve or resource viewpoint. The main uranium occurrences ares (1) In the Upper Cambrian graphite schists corresponding to the culm of Sweden small zones are found (30 - 50 cm thick) with an average of 20 ppm uranium. (2) Near Vise at the base of the Carboniferous the Visean formation is discordantly superimposed on the Permian (Frasnian) and overlain by shales and phyllites. Solution pockets at the boundary contain phosphatic lenses that contain uranium values of up to 200 ppm. Autunite and Torbernite are the main uranium minerals associated with a number of complex phosphatic minerals. Within the Chalk (Maestrichtien) of the Mons basin, that is mainly in the Ciply - St. Symphorien and Baudow district. Here is found enrichment of uranium up to 140 ppm over large areas related to phosphatic chalk. The thickness of the zone varies from a few to 20 metres. However, as the P 2 O 5 content is not high enough for the deposits to be exploited at present for phosphate there is little possibility of the uranium being concentrated at high enough levels to be exploited for itself alone. (4) Near to Vielsalm (in the Stavelot Massif) are some thin quartz veins containing small amounts of copper and uranium minerals (Torbornite). Values of up to 70 ppm are recorded. (5) A number of low uranium values are recorded associated with phosphatic nodules and zones in the Lower Pleistocene and Tertiary

The current situation of uranium mining in Hungary

International Nuclear Information System (INIS)

Erdi-Krausz, G.

1997-01-01

The paper describes the history of uranium production in Hungary. It focuses on the Mecsek Ore Mining Company, now known as Mecsekuran Limited, and its relationship with the Hungarian Government. From the start of uranium production in 1963 until May 1989 all production was exported to the Soviet Union under a bilateral contract. In exchange the Soviet Union agreed to provide fabricated fuel for the future Hungarian nuclear power plant. In May 1989 the Government of Hungary announced closure of its uranium mining operations because of the high cost of production. The paper describes the history of events since 1989, as well as the current plans to terminate all uranium production by 31 December 1997. The Mecsek Mountains lie in the southern part of Hungary, west from the Danube, about 30 km from the former Yugoslavian border, and north from the city of Pecs. Its eastern side is built up from medieval limestone and dolomites, while the western part is from sandstone and clay from the geological Paleozoic. In the eastern part high quality cokeable coal has been mined for more than 200 years, east from the city of Pecs; and in the western part uranium ore was discovered and the mining began only a few decades ago. (author)

New french uranium mineral species

International Nuclear Information System (INIS)

Branche, G.; Chervet, J.; Guillemin, C.

1952-01-01

In this work, the authors study the french new uranium minerals: parsonsite and renardite, hydrated phosphates of lead and uranium; kasolite: silicate hydrated of uranium and lead uranopilite: sulphate of uranium hydrated; bayleyite: carbonate of uranium and of hydrated magnesium; β uranolite: silicate of uranium and of calcium hydrated. For all these minerals, the authors give the crystallographic, optic characters, and the quantitative chemical analyses. On the other hand, the following species, very rare in the french lodgings, didn't permit to do quantitative analyses. These are: the lanthinite: hydrated uranate oxide; the α uranotile: silicate of uranium and of calcium hydrated; the bassetite: uranium phosphate and of hydrated iron; the hosphuranylite: hydrated uranium phosphate; the becquerelite: hydrated uranium oxide; the curite: oxide of uranium and lead hydrated. Finally, the authors present at the end of this survey a primary mineral: the brannerite, complex of uranium titanate. (author) [fr

Evaluation of the LASL automated spectrophotometer for uranium determination at submilligram levels

International Nuclear Information System (INIS)

Hollen, R.M.; Jackson, D.D.; Rein, J.E.

1977-07-01

The LASL automated spectrophotometer, designed for determination of 1 to 14 mg of uranium and 0.5 to 14 mg of plutonium, has been evaluated for determination of lower levels of uranium to 0.12 mg. The essentially linear response of absorbance is maintained and the standard deviation for a single measurement is constant at about 0.013 mg of uranium, corresponding to a maximum uncertainty of about 10 percent at the 0.12-mg limit. The instrument was applied to the analysis of a series of low-level-concentration, 0.07- to 0.8-mg/ml uranium samples. The results were not statistically different from those obtained by a manual spectrophotometric method

ERA`s Ranger uranium mine

Energy Technology Data Exchange (ETDEWEB)

Davies, W. [Energy Resources of Australia Ltd., Sydney, NSW (Australia)

1997-12-31

Energy Resource of Australia (ERA) is a public company with 68% of its shares owned by the Australian company North Limited. It is currently operating one major production centre - Ranger Mine which is 260 kilometres east of Darwin, extracting and selling uranium from the Ranger Mine in the Northern Territory to nuclear electricity utilities in Japan, South Korea, Europe and North America. The first drum of uranium oxide from Ranger was drummed in August 1981 and operations have continued since that time. ERA is also in the process of working towards obtaining approvals for the development of a second mine - Jabiluka which is located 20 kilometres north of Ranger. The leases of Ranger and Jabiluka adjoin. The Minister for the Environment has advised the Minister for Resources and Energy that there does not appear to be any environmental issue which would prevent the preferred Jabiluka proposal from proceeding. Consent for the development of ERA`s preferred option for the development of Jabiluka is being sought from the Aboriginal Traditional Owners. Ranger is currently the third largest producing uranium mine in the world producing 4,237 tonnes of U{sub 3}O{sub 8} in the year to June 1997.

Uranium in Kosovo's drinking water.

Science.gov (United States)

Berisha, Fatlume; Goessler, Walter

2013-11-01

The results of this paper are an initiation to capture the drinking water and/or groundwater elemental situation in the youngest European country, Kosovo. We aim to present a clear picture of the natural uranium concentration in drinking water and/or groundwater as it is distributed to the population of Kosovo. Nine hundred and fifty-one (951) drinking water samples were analyzed by inductively coupled plasma mass spectrometry (ICPMS). The results are the first countrywide interpretation of the uranium concentration in drinking water and/or groundwater, directly following the Kosovo war of 1999. More than 98% of the samples had uranium concentrations above 0.01 μg L(-1), which was also our limit of quantification. Concentrations up to 166 μg L(-1) were found with a mean of 5 μg L(-1) and median 1.6 μg L(-1) were found. Two point six percent (2.6%) of the analyzed samples exceeded the World Health Organization maximum acceptable concentration of 30 μg L(-1), and 44.2% of the samples exceeded the 2 μg L(-1) German maximum acceptable concentrations recommended for infant food preparations. Copyright © 2013 Elsevier Ltd. All rights reserved.

Why can rossing uranium mine keep mining even in low price conditions of uranium market

International Nuclear Information System (INIS)

Tan Chenglong

2004-01-01

Rossing uranium mine is the only operating uranium mine in the world where the uranium occurs in intrusive alaskite. In the past 10 years, uranium market regressed in the world, uranium production weakened, expenditures of capital for uranium exploration were insufficient. Uranium spot market price rapidly decreased from $111.8/kg U in late 1970's to $22.1/kg U in mid-1990's. Why can Rossing uranium mine mined with traditional underground and open pit operation can keep running even in low price conditions of uranium market? Augumenting research on the deposit, mineral and technology, decreasing production cost and improving selling strategy can not only maintain Rossing's uranium production at present, but also ensure sustainable development in the coming 15 years. Exploration of low-costed uranium deposits is very important. However, obvious economic benefits can be obtained, as Rossing uranium mine does, by augumenting geological-economical research on the known uranium deposits of hard-rock type and by using new techniques to improve the conventional techniques in the uranium mine development. (authors)

Models for estimating the radiation hazards of uranium mines

International Nuclear Information System (INIS)

Wise, K.N.

1982-01-01

Hazards to the health of workers in uranium mines derive from the decay products of radon and from uranium and its descendants. Radon daughters in mine atmospheres are either attached to aerosols or exist as free atoms and their physical state determines in which part of the lung the daughters deposit. The factors which influence the proportions of radon daughters attached to aerosols, their deposition in the lung and the dose received by the cells in lung tissue are discussed. The estimation of dose to tissue from inhalation or ingestion of uranium and daughters is based on a different set of models which have been applied in recent ICRP reports. The models used to describe the deposition of particulates, their movement in the gut and their uptake by organs, which form the basis for future limits on the concentration of uranium and daughters in air or on their intake with food, are outlined

Models for estimating the radiation hazards of uranium mines

International Nuclear Information System (INIS)

Wise, K.N.

1990-01-01

Hazards to the health of workers in uranium mines derive from the decay products of radon and from uranium and its descendants. Radon daughters in mine atmospheres are either attached to aerosols or exist as free atoms and their physical state determines in which part of the lung the daughters deposit. The factors which influence the proportions of radon daughters attached to aerosols, their deposition in the lung and the dose received by the cells in lung tissue are discussed. The estimation of dose to tissue from inhalation of ingestion or uranium and daughters is based on a different set of models which have been applied in recent ICRP reports. The models used to describe the deposition of particulates, their movement in the gut and their uptake by organs, which form the basis for future limits on the concentration of uranium and daughters in air or on their intake with food, are outlined. 34 refs., 12 tabs., 9 figs

Uranium in Canada

International Nuclear Information System (INIS)

1987-09-01

Canadian uranium exploration and development efforts in 1985 and 1986 resulted in a significant increase in estimates of measured uranium resources. New discoveries have more than made up for production during 1985 and 1986, and for the elimination of some resources from the overall estimates, due to the sustained upward pressure on production costs and the stagnation of uranium prices in real terms. Canada possesses a large portion of the world's uranium resources that are of current economic interest and remains the major focus of inter-national uranium exploration activity. Expenditures for uranium exploration in Canada in 1985 and 1986 were $32 million and $33 million, respectively. Although much lower than the $130 million total reported for 1979, expenditures for 1987 are forecast to increase. Exploration and surface development drilling in 1985 and 1986 were reported to be 183 000 m and 165σ2 000 m, respectively, 85 per cent of which was in Saskatchewan. Canada has maintained its position as the world's leading producer and exporter of uranium. By the year 2000, Canada's annual uranium requirements will be about 2 100 tU. Canada's known uranium resources are more than sufficient to meet the 30-year fuel requirements of those reactors in Canada that are either in operation now or expected to be in service by the late 1990s. A substantial portion of Canada's identified uranium resources is thus surplus to Canadian needs and available for export. Annual sales currently approach $1 billion, of which exports account for 85 per cent. Forward domestic and export contract commitments totalled 73 000 tU and 62 000 tU, respectively, as of early 1987

Uranium - what role

International Nuclear Information System (INIS)

Grey, T.; Gaul, J.; Crooks, P.; Robotham, R.

1980-01-01

Opposing viewpoints on the future role of uranium are presented. Topics covered include the Australian Government's uranium policy, the status of nuclear power around the world, Australia's role as a uranium exporter and problems facing the nuclear industry

Uranium's scientific history

International Nuclear Information System (INIS)

Goldschmidt, B.

1990-01-01

The bicentenary of the discovery of uranium coincides with the fiftieth anniversary of the discovery of fission, an event of worldwide significance and the last episode in the uranium -radium saga which is the main theme of this paper. Uranium was first identified by the German chemist Martin Klaproth in 1789. He extracted uranium oxide from the ore pitchblende which was a by-product of the silver mines at Joachimsthal in Bohemia. For over a century after its discovery, the main application for uranium derived from the vivid colours of its oxides and salts which are used in glazes for ceramics, and porcelain. In 1896, however, Becquerel discovered that uranium emitted ionizing radiation. The extraction by Pierre and Marie Curie of the more radioactive radium from uranium in the early years of the twentieth century and its application to the treatment of cancer shifted the chief interest to radium production. In the 1930s the discovery of the neutron and of artificial radioactivity stimulated research in a number of European laboratories which culminated in the demonstration of fission by Otto Frisch in January 1939. The new found use of uranium for the production of recoverable energy, and the creation of artificial radioelements in nuclear reactors, eliminated the radium industry. (author)

Uranium tipped ammunition

International Nuclear Information System (INIS)

Roche, P.

1993-01-01

During the uranium enrichment process required to make nuclear weapons or fuel, the concentration of the 'fissile' U-235 isotope has to be increased. What is left, depleted uranium, is about half as radioactive as natural uranium, but very dense and extremely hard. It is used in armour piercing shells. External radiation levels from depleted uranium (DU) are low. However DU is about as toxic as lead and could be harmful to the kidneys if eaten or inhaled. It is estimated that between 40 and 300 tonnes of depleted uranium were left behind by the Allied armies after the Gulf war. The biggest hazard would be from depleted uranium shells which have hit Iraqui armoured vehicles and the resulting dust inhaled. There is a possible link between depleted uranium shells and an illness known as 'Desert Storm Syndrome' occurring in some Gulf war veterans. As these shells are a toxic and radioactive hazard to health and the environment their use and testing should be stopped because of the risks to troops and those living near test firing ranges. (UK)

Uranium enrichment

International Nuclear Information System (INIS)

1989-01-01

GAO was asked to address several questions concerning a number of proposed uranium enrichment bills introduced during the 100th Congress. The bill would have restructured the Department of Energy's uranium enrichment program as a government corporation to allow it to compete more effectively in the domestic and international markets. Some of GAO's findings discussed are: uranium market experts believe and existing market models show that the proposed DOE purchase of a $750 million of uranium from domestic producers may not significantly increase production because of large producer-held inventories; excess uranium enrichment production capacity exists throughout the world; therefore, foreign producers are expected to compete heavily in the United States throughout the 1990s as utilities' contracts with DOE expire; and according to a 1988 agreement between DOE's Offices of Nuclear Energy and Defense Programs, enrichment decommissioning costs, estimated to total $3.6 billion for planning purposes, will be shared by the commercial enrichment program and the government

Uranium resources

International Nuclear Information System (INIS)

1976-01-01

This is a press release issued by the OECD on 9th March 1976. It is stated that the steep increases in demand for uranium foreseen in and beyond the 1980's, with doubling times of the order of six to seven years, will inevitably create formidable problems for the industry. Further substantial efforts will be needed in prospecting for new uranium reserves. Information is given in tabular or graphical form on the following: reasonably assured resources, country by country; uranium production capacities, country by country; world nuclear power growth; world annual uranium requirements; world annual separative requirements; world annual light water reactor fuel reprocessing requirements; distribution of reactor types (LWR, SGHWR, AGR, HWR, HJR, GG, FBR); and world fuel cycle capital requirements. The information is based on the latest report on Uranium Resources Production and Demand, jointly issued by the OECD's Nuclear Energy Agency (NEA) and the International Atomic Energy Agency. (U.K.)

Standardization of solvent extraction procedure for determination of uranium in sea water

International Nuclear Information System (INIS)

Maity, Sukanta; Dusane, C.B.; Sahu, S.K.; Pandit, G.G.

2014-01-01

Marine ecosystem is becoming polluted by heavy metals and naturally occurring radionuclides due to rapid industrialization and human activities. Many contaminants such as heavy metals and naturally occurring radionuclides though occur at extremely low concentration in sea water, are accumulated by marine organisms and concentrations in their body tissue can be hundreds of times greater than sea water. As human being consume different marine organisms like biota, can lead potential health problem to human being. Uranium is a naturally occurring radioactive element which is important for nuclear technology. However, mineral resources for uranium are limited. Seawater is a major source of uranium. The total estimated quantity of uranium in seawater is around four and a half billion tones. Thus, the oceans have the potential to become the most eco-friendly and long sustainable resource for uranium. A number of countries in the world are in search of techniques to recover uranium from seawater economically. For this purpose and also for the environmental monitoring, the determination of uranium in seawater is very much important. Seawater contains very high concentrations of salts and its uranium content is very low. Accordingly, the separation and preconcentration of uranium is usually involved in the analytical procedures used for the determination of uranium in seawater. In the present study solvent extraction procedure was adopted for the determination of uranium in sea water collected from different locations across Thane Creek area, Mumbai, India

Radioactive pollution investigation and disposal of abandoned uranium mines in Jiangsu province

International Nuclear Information System (INIS)

Zhang Qihong; Zhao Fuxiang; Wang Lihua

2008-01-01

The environment influence of five abandoned uranium mines in Jiangsu province from 1950s to 1960s is introduced. By monitoring air absorbed dose rate of external exposure γ radiation, it is found that the pollution scope of No.1 abandoned uranium mine is the biggest in five abandoned uranium mines. The No. 2 and No. 3 mine areas has achieved the limit use after they were desposed. The radioactivity and the gamma nuclein in solid samples(slag, soil, silt) and liquid samples (the surface water, the well water)of No. 1 abandoned uranium mine were further analyzed and measured, the measured values are higher. The pollution of abandoned uranium mines still exists and diffuses after 30 years. According to the monitoring results and the analysis of pollution present situation, suggestions and measures are proposed for the pollution control. (authors)

Modelling of redox front and uranium movement in a uranium mine at Pocos de Caldas, Brazil

International Nuclear Information System (INIS)

Cross, J.E.; Gabriel, D.S.; Haworth, A.; Sharland, S.M.; Tweed, C.J.

1991-04-01

A study of the migration of uranium at the Pocos de Caldas uranium mine in Brazil under the influence of the infiltration of oxidising groundwaters has been performed. The modelling was carried out using the coupled chemical equilibria/transport code CHEQMATE. The work presented in this paper extends a previous study. Results give some encouraging agreements with field data, generally increasing confidence in the use of such modelling techniques in problems associated with the migration of radionuclides away from a nuclear waste repository. For particular aspects of the problem where good agreement with field data was not obtained, a number of reasons have been suggested. This study also highlights the importance of accurate thermodynamic data and choice of solubility-limiting mineral phases for modelling such systems. (author)

Uranium - the world picture

International Nuclear Information System (INIS)

Silver, J.M.; Wright, W.J.

1976-01-01

The world resources of uranium and the future demand for uranium are discussed. The amount of uranium available depends on the price which users are prepared to pay for its recovery. As the price is increased, there is an incentive to recover uranium from lower grade or more difficult deposits. In view of this, attention is drawn to the development of the uranium industry in Australias

Radiological hazards to uranium miners

International Nuclear Information System (INIS)

1990-05-01

The purpose of the present document is to review and assess the occupational hazards to uranium miners in Canada. Amendments to regulations set the maximum permissible dose to uranium miners at 50 mSv per year. Uranium miners are exposed to radon and thoron progeny, external gamma radiation and long-lived alpha-emitting radionuclides in dust. The best estimate for the lifetime risk of inhaled radon progeny is about 3 x 10 -4 lung cancers per WLM for the average miner, with a range of uncertainty from about 1 -6 x 10 -4 per WLM. This central value is nearly twice as high as that recommended by the ICRP in 1981. The probability of serious biological consequences following exposure to external gamma rays is currently under review but is expected to be in the range of 3 - 6 x 10 -2 Sv -1 . Dosimetric calculations indicate that the stochastic risks per WLM of thoron progeny are about one-third of those for radon progeny. The annual limits on intake of inhaled ore dusts recommended by the ICRP are probably too low by at least a factor of two for the type of ore and dust normally encountered in underground uranium mines in Ontario; this is due in part to the fact that the average diameter of these dusts is five times greater than the value used by the ICRP. Radiological exposures of uranium miners in Canada were reviewed. The biological impact of these exposures were compared with those of conventional accidents on the basis of the years of normal life expectancy that are lost or seriously impaired due to occupational hazards. The objectives in considering all occupational risks are to reduce the total risk from all causes and to use funds spent for health protection as effectively as possible

Cellular localization of uranium in the renal proximal tubules during acute renal uranium toxicity.

Science.gov (United States)

Homma-Takeda, Shino; Kitahara, Keisuke; Suzuki, Kyoko; Blyth, Benjamin J; Suya, Noriyoshi; Konishi, Teruaki; Terada, Yasuko; Shimada, Yoshiya

2015-12-01

Renal toxicity is a hallmark of uranium exposure, with uranium accumulating specifically in the S3 segment of the proximal tubules causing tubular damage. As the distribution, concentration and dynamics of accumulated uranium at the cellular level is not well understood, here, we report on high-resolution quantitative in situ measurements by high-energy synchrotron radiation X-ray fluorescence analysis in renal sections from a rat model of uranium-induced acute renal toxicity. One day after subcutaneous administration of uranium acetate to male Wistar rats at a dose of 0.5 mg uranium kg(-1) body weight, uranium concentration in the S3 segment of the proximal tubules was 64.9 ± 18.2 µg g(-1) , sevenfold higher than the mean renal uranium concentration (9.7 ± 2.4 µg g(-1) ). Uranium distributed into the epithelium of the S3 segment of the proximal tubules and highly concentrated uranium (50-fold above mean renal concentration) in micro-regions was found near the nuclei. These uranium levels were maintained up to 8 days post-administration, despite more rapid reductions in mean renal concentration. Two weeks after uranium administration, damaged areas were filled with regenerating tubules and morphological signs of tissue recovery, but areas of high uranium concentration (100-fold above mean renal concentration) were still found in the epithelium of regenerating tubules. These data indicate that site-specific accumulation of uranium in micro-regions of the S3 segment of the proximal tubules and retention of uranium in concentrated areas during recovery are characteristics of uranium behavior in the kidney. Copyright © 2015 John Wiley & Sons, Ltd.

Development of a choronocoulometric method for determining traces of uranium using the catalytic nitrate reduction

International Nuclear Information System (INIS)

Cantagallo, M.I.C.; Gutz, I.G.R.

1990-01-01

With the aim of improving the sensitivity of the electroanalytical determination of uranium at trace levels. The uranium catalyzed reduction of nitrate on mercury electrode and the technique of chronocoulometry were used. Several experimental parameters were investigated (electrolyte composition, potential program, integration time, blank correction, temperature, previous separation) and adequate conditions were selected for the analytical determination. Under these conditions it was possible to exceed the best reported sensitivity for the catalytic determination, extending the detection limit to 3.10 -10 M. Exploratory study of the combination of this procedure with pre-concentration of uranium ions on the electrode revealed a detection limit ten limes lower. (author) [pt

The uranium in the environment; L'uranium dans l'environnement

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-07-01

The uranium is a natural element omnipresent in the environment, with a complex chemistry more and more understood. Many studies are always today devoted to this element to better improve the uranium behavior in the environment. To illustrate this knowledge and for the public information the CEA published this paper. It gathers in four chapters: historical aspects and properties of the uranium, the uranium in the environment and the impacts, the metrology of the uranium and its migration. (A.L.B.)

Small cell experiments for electrolytic reduction of uranium oxides to uranium metal using fluoride salts

International Nuclear Information System (INIS)

Haas, P.A.; Adcock, P.W.; Coroneos, A.C.; Hendrix, D.E.

1994-01-01

Electrolytic reduction of uranium oxide was proposed for the preparation of uranium metal feed for the atomic vapor laser isotope separation (AVLIS) process. A laboratory cell of 25-cm ID was operated to obtain additional information in areas important to design and operation of a pilot plant cell. Reproducible test results and useful operating and control procedures were demonstrated. About 20 kg of uranium metal of acceptable purity were prepared. A good supply of dissolved UO 2 feed at the anode is the most important controlling requirement for efficient cell operation. A large fraction of the cell current is nonproductive in that it does not produce a metal product nor consume carbon anodes. All useful test conditions gave some reduction of UF 4 to produce CF 4 in addition to the reduction of UO 2 , but the fraction of metal from the reduction of UF 4 can be decreased by increasing the concentration of dissolved UO 2 . Operation of large continuous cells would probably be limited to current efficiencies of less than 60 pct, and more than 20 pct of the metal would result from the reduction of UF 4

Characterization of uranium in bituminized radioactive waste drums by self-induced X-ray fluorescence

International Nuclear Information System (INIS)

Pin, Patrick; Perot, Bertrand

2013-06-01

This paper reports the experimental qualification of an original uranium characterization method based on fluorescence X rays induced by the spontaneous gamma emission of bituminized radioactive waste drums. The main 661.7 keV gamma ray following the 137 Cs decay produces by Compton scattering in the bituminized matrix an intense photon continuum around 100 keV, i.e. in the uranium X-ray fluorescence region. 'Self-induced' X-rays produced without using an external source allow a quantitative assessment of uranium as 137 Cs and uranium are homogeneously mixed and distributed in the bituminized matrix. The paper presents the experimental qualification of the method with real waste drums, showing a detection limit well below 1 kg of uranium in 20 min acquisitions while the usual gamma rays of 235 U (185 keV) or 238 U (1001 keV of 234m Pa in the radioactive decay chain) are not detected. The relative uncertainty on the uranium mass assessed by self-induced X-ray fluorescence (SXRF) is about 50%, with a 95% confidence level, taking into account the correction of photon attenuation in the waste matrix. This last indeed contains high atomic numbers elements like uranium, but also barium, in quantities which are not known for each drum. Attenuation is estimated thanks to the peak-to-Compton ratio to limit the corresponding uncertainty. The SXRF uranium masses measured in the real drums are in good agreement with long gamma-ray spectroscopy measurements (1001 keV peak) or with radiochemical analyses. (authors)

Identification of chemical processes influencing constituent mobility during in-situ uranium leaching

International Nuclear Information System (INIS)

Sherwood, D.R.; Hostetler, C.J.; Deutsch, W.J.

1984-07-01

In-situ leaching of uranium has become a widely accepted method for production of uranium concentrate from ore zones that are too small, too deep, and/or too low in grade to be mined by conventional techniques. One major environmental concern that exists with in-situ leaching of uranium is the possible adverse effects mining might have on regional ground water quality. The leaching solution (lixiviant), which extracts uranium from the ore zone, might also mobilize other potential contaminants (As, Se, Mo, and SO 4 ) associated with uranium ore. Column experiments were performed to investigate the geochemical interactions between a lixiviant and a uranium ore during in-situ leaching and to identify chemical processes that might influence contaminant mobility. The analytical composition data for selected column effluents were used with the MINTEQ code to develop a computerized geochemical model of the system. MINTEQ was used to calculate saturation indices for solid phases based on the composition of the solution. A potential constraint on uranium leaching efficiency appears to be the solubility control of schoepite. Gypsum and powellite solubilities may limit the mobilities of sulfate and molybdenum, respectively. In contrast, the mobilities of arsenic and selenium were not limited by solubility constraints, but were influenced by other chemical interaction between the solution and sediment, perhaps adsorption. Bulk chemical and mineralogical analyses were performed on both the original and leached ores. Using these analyses together with the column effluent data, mass balance calculations were performed on five constituents based on solution chemical analysis and bulk chemical and γ-spectroscopy analysis for the sediment. 6 references, 10 figures, 10 tables

Transformation of human osteoblast cells to the tumorigenic phenotype by depleted uranium-uranyl chloride.

OpenAIRE

Miller, A C; Blakely, W F; Livengood, D; Whittaker, T; Xu, J; Ejnik, J W; Hamilton, M M; Parlette, E; John, T S; Gerstenberg, H M; Hsu, H

1998-01-01

Depleted uranium (DU) is a dense heavy metal used primarily in military applications. Although the health effects of occupational uranium exposure are well known, limited data exist regarding the long-term health effects of internalized DU in humans. We established an in vitro cellular model to study DU exposure. Microdosimetric assessment, determined using a Monte Carlo computer simulation based on measured intracellular and extracellular uranium levels, showed that few (0.0014%) cell nuclei...

Analytical strategies for uranium determination in natural water and industrial effluents samples

International Nuclear Information System (INIS)

Santos, Juracir Silva

2011-01-01

The work was developed under the project 993/2007 - 'Development of analytical strategies for uranium determination in environmental and industrial samples - Environmental monitoring in the Caetite city, Bahia, Brazil' and made possible through a partnership established between Universidade Federal da Bahia and the Comissao Nacional de Energia Nuclear. Strategies were developed to uranium determination in natural water and effluents of uranium mine. The first one was a critical evaluation of the determination of uranium by inductively coupled plasma optical emission spectrometry (ICP OES) performed using factorial and Doehlert designs involving the factors: acid concentration, radio frequency power and nebuliser gas flow rate. Five emission lines were simultaneously studied (namely: 367.007, 385.464, 385.957, 386.592 and 409.013 nm), in the presence of HN0 3 , H 3 C 2 00H or HCI. The determinations in HN0 3 medium were the most sensitive. Among the factors studied, the gas flow rate was the most significant for the five emission lines. Calcium caused interference in the emission intensity for some lines and iron did not interfere (at least up to 10 mg L -1 ) in the five lines studied. The presence of 13 other elements did not affect the emission intensity of uranium for the lines chosen. The optimized method, using the line at 385.957 nm, allows the determination of uranium with limit of quantification of 30 μg L -1 and precision expressed as RSD lower than 2.2% for uranium concentrations of either 500 and 1000 μg L -1 . In second one, a highly sensitive flow-based procedure for uranium determination in natural waters is described. A 100-cm optical path flow cell based on a liquid-core waveguide (LCW) was exploited to increase sensitivity of the arsenazo 111 method, aiming to achieve the limits established by environmental regulations. The flow system was designed with solenoid micro-pumps in order to improve mixing and minimize reagent consumption, as well as

Recovery of uranium from low-grade sandstone ores and phosphate rock

Energy Technology Data Exchange (ETDEWEB)

Kennedy, R H [United States Atomic Energy Commission, Washington, D. C. (United States)

1967-06-15

This paper is concerned principally with commercial-scale experience in the United States in the recovery of uranium from low-grade sources. Most of these operations have been conducted by the operators of uranium mills as an alternative to processing normal-grade ores. The operations have been generally limited, therefore, to the treatment of low-grade materials generated in the course of mining normal-grade ores. In some circumstances such materials can be treated by simplified procedures as an attractive source of additional production. The experience gained in uranium recovery from phosphate rock will be treated in some detail. The land pebble phosphate rock of central Florida generally contains about 0.01 to 0.02% U{sub 3}O{sub 8}. While no uranium is being recovered from this source at the present time, it does represent a significant potential source of by-product uranium production because of the large tonnages being mined. (author)

European needs for uranium in relation to world supply and demand

International Nuclear Information System (INIS)

Davis, M.

1977-01-01

The paper explains why Western Europe, and in particular the European Community, is engaged in an important diversification of energy sources to nuclear generated electricity. The resulting Western European demand for uranium (most of which will have to be imported) is quantified and discussed in relation to the needs of North America and Japan and the latest estimates of world uranium resources and production capability. The European Community will be the largest purchaser of uranium from a variety of sources on the world market. It is shown that the lower limits of past estimates for uranium demand appear to be the most reliable so far; the causes and effects of uncertainty for the future are outlined; and the need for exploration is emphasized. It is maintained that although close collaboration between electricity utilities and mining companies is highly desirable, the goal of an orderly market (which should be achievable for uranium) will not be achieved without a positive and constructive contribution being made by public authorities. (author)

Uranium loans

International Nuclear Information System (INIS)

Anon.

1990-01-01

When NUEXCO was organized in 1968, its founders conceived of a business based on uranium loans. The concept was relatively straightforward; those who found themselves with excess supplies of uranium would deposit those excesses in NUEXCO's open-quotes bank,close quotes and those who found themselves temporarily short of uranium could borrow from the bank. The borrower would pay interest based on the quantity of uranium borrowed and the duration of the loan, and the bank would collect the interest, deduct its service fee for arranging the loan, and pay the balance to those whose deposits were borrowed. In fact, the original plan was to call the firm Nuclear Bank Corporation, until it was discovered that using the word open-quotes Bankclose quotes in the name would subject the firm to various US banking regulations. Thus, Nuclear Bank Corporation became Nuclear Exchange Corporation, which was later shortened to NUEXCO. Neither the nuclear fuel market nor NUEXCO's business developed quite as its founders had anticipated. From almost the very beginning, the brokerage of uranium purchases and sales became a more significant activity for NUEXCO than arranging uranium loans. Nevertheless, loan transactions have played an important role in the international nuclear fuel market, requiring the development of special knowledge and commercial techniques

Experiments of JRR-4 low-enriched-uranium-silicied fuel core

International Nuclear Information System (INIS)

Hirane, Nobuhiko; Ishikuro, Yasuhiro; Nagadomi, Hideki; Yokoo, Kenji; Horiguchi, Hironori; Nemoto, Takumi; Yamamoto, Kazuyoshi; Yagi, Masahiro; Arai, Nobuyoshi; Watanabe, Shukichi; Kashima, Yoichi

2006-03-01

JRR-4, a light-water-moderated and cooled, swimming pool type research reactor using high-enriched uranium plate-type fuels had been operated from 1965 to 1996. In order to convert to low-enriched-uranium-silicied fuels, modification work had been carried out for 2 years, from 1996 to 1998. After the modification, start-up experiments were carried out to obtain characteristics of the low-enriched-uranium-silicied fuel core. The measured excess reactivity, reactor shutdown margin and the maximum reactivity addition rate satisfied the nuclear limitation of the safety report for licensing. It was confirmed that conversion to low-enriched-uranium-silicied fuels was carried out properly. Besides, the necessary data for reactor operation were obtained, such as nuclear, thermal hydraulic and reactor control characteristics. This report describes the results of start-up experiments and burnup experiments. The first criticality of low-enriched-uranium-silicied core was achieved on 14th July 1998, and the operation for joint-use has been carried out since 6th October 1998. (author)

Technological study about a disposal measures of low-level radioactive waste including uranium and long-half-life radionuclides

International Nuclear Information System (INIS)

Sugaya, Toshikatsu; Nakatani, Takayoshi; Sakai, Akihiro; Sakamoto, Yoshiaki; Sasaki, Toshihisa; Nakamura, Yasuo

2017-02-01

Japan Atomic Energy Agency (JAEA) performed the technical studies contributed for the disposal measures of uranium-bearing waste with low concentration and intermediate depth disposal-based waste occurring from the process of the nuclear fuel cycle. (1) Study of the trench disposal of uranium-bearing waste. As a part of the study of disposal measures of the uranium-bearing waste, we carried out the safety assessment (exposure dose assessment) and derived the upper limit of radioactivity concentration of uranium which was allowed to be included in radioactive waste for trench disposal. (2) Preliminary study for the expansion of material applied to clearance in uranium-bearing waste. Currently, the clearance level of uranium handling facilities was derived from the radioactivity concentration of uranium corresponding to dose criterion about the exposure pathways of the reuse and recycle of metal. Therefore, we preliminarily evaluated whether metal and concrete were able to be applied to clearance by the method of the undergrounding disposal. (3) Study of the concentration limitation scenarios for the intermediate depth disposal-based waste. We carried out dose assessment of intermediate depth disposal of radioactive waste generated from JAEA about radioactive concentration limitation scenarios of which the concept was shown by the study team in Nuclear Regulation Authority. Based on the results, we discussed whether the waste was applied to radioactive waste conforming to concept of intermediate depth disposal. (author)

Uranium isotopes in groundwater: their use in prospecting for sandstone-type uranium deposits

International Nuclear Information System (INIS)

Cowart, J.B.; Osmond, J.K.

1977-01-01

The relative abundances of dissolved 238 U and its daughter 234 U appear to be greatly affected as the uranium is transported downdip in sandstone aquifers. In an actively forming uranium accumulation at a reducing barrier, an input of 234 U occurs in proximity to the isotopically non-selective precipitation of uranium from the water. The result is a downdip water much lower in uranium concentration but relatively enriched in 234 U. The measurement of isotopic as well as concentration changes may increase the effectiveness of hydrogeochemical exploration of uranium. The investigation includes the uranium isotopic patterns in aquifers associated with known uranium orebodies in the Powder River and Shirley Basins, Wyoming, and Karnes County, Texas, USA. In addition, the Carrizo sandstone aquifer of Texas was studied in detail and the presence of an uranium accumulation inferred

Uranium market and resources

International Nuclear Information System (INIS)

Capus, G.; Arnold, Th.

2004-01-01

The controversy about the extend of the uranium resources worldwide is still important, this article sheds some light on this topic. Every 2 years IAEA and NEA (nuclear energy agency) edit an inventory of uranium resources as reported by contributing countries. It appears that about 4.6 millions tons of uranium are available at a recovery cost less than 130 dollars per kg of uranium and a total of 14 millions tons of uranium can be assessed when including all existing or supposed resources. In fact there is enough uranium to sustain a moderate growth of the park of nuclear reactors during next decades and it is highly likely that the volume of uranium resources can allow a more aggressive development of nuclear energy. It is recalled that a broad use of the validated breeder technology can stretch the durability of uranium resources by a factor 50. (A.C.)

An Investigation on the Persistence of Uranium Hydride during Storage of Simulant Nuclear Waste Packages.

Science.gov (United States)

Stitt, C A; Harker, N J; Hallam, K R; Paraskevoulakos, C; Banos, A; Rennie, S; Jowsey, J; Scott, T B

2015-01-01

Synchrotron X-rays have been used to study the oxidation of uranium and uranium hydride when encapsulated in grout and stored in de-ionised water for 10 months. Periodic synchrotron X-ray tomography and X-ray powder diffraction have allowed measurement and identification of the arising corrosion products and the rates of corrosion. The oxidation rates of the uranium metal and uranium hydride were slower than empirically derived rates previously reported for each reactant in an anoxic water system, but without encapsulation in grout. This was attributed to the grout acting as a physical barrier limiting the access of oxidising species to the uranium surface. Uranium hydride was observed to persist throughout the 10 month storage period and industrial consequences of this observed persistence are discussed.

Adsorptive differential pulse voltammetry for determination of uranium in sea water

International Nuclear Information System (INIS)

Khandekar, R.N.; Raghunath, R.

1990-01-01

An adsorptive stripping voltammetric procedure for direct determination of trace quantities of uranium in sea water is described. Optimal conditions include pH 6.7, 2 x 10 -5 M 8-hydroxyquinoline (oxine) and collection potential of -0.4V (vs Ag/AgCl) at hanging mercury drop electrode. With controlled adsorptive accumulation for one min. a detection limit of 2.8 x 10 -10 M uranium is obtained. The response is linear upto 7 x 10 -8 M uranium and the relative standard deviation at 4 x 10 -9 M uranium is 11.5%. The effect of possible interference from other metals has been investigated. The accuracy of the method has been tested by comparison with the results obtained by fluorimetric method. (author). 2 figs., 1 tab., 20 refs

Translocation of uranium from water to foodstuff while cooking

International Nuclear Information System (INIS)

Krishnapriya, K.C.; Baksi, Ananya; Chaudhari, Swathi; Gupta, Soujit Sen; Pradeep, T.

2015-01-01

Highlights: • Rice can efficiently uptake uranium from water contaminated with uranyl nitrate hexahydrate (UO 2 (NO 3 ) 2.6 H 2 O), while cooking. • Unusual uranium uptake to the extent of about 1000 ppm is observed when rice is cooked in highly concentrated uranium contaminated water (1240 ppm). • Nature of interaction of uranium with carbohydrates is probed using small monosaccharides like glucose and mannose. • Electrospray ionization mass spectrometry showed UO 2 2+ to be the most stable species in water in such solutions which can form complexes with sugars. • The species (UO 2 2+ ) is also observed in the case of water exposed to the common mineral, uranium oxide (UO 2 ) and similar type of complexation is observed with sugars. - Abstract: The present work report the unusual uranium uptake by foodstuff, especially those rich in carbohydrates like rice when they are cooked in water, contaminated with uranium. The major staple diet in South Asia, rice, was chosen to study its interaction with UO 2 2+ , the active uranium species in water, using inductively coupled plasma mass spectrometry. Highest uptake limit was checked by cooking rice at very high uranium concentration and it was found to be good scavenger of uranium. To gain insight into the mechanism of uptake, direct interaction of UO 2 2+ with monosaccharides was also studied, using electrospray ionization mass spectrometry taking mannose as a model. The studies have been done with dissolved uranium salt, uranyl nitrate hexahydrate (UO 2 (NO 3 ) 2 ·6H 2 O), as well as the leachate of a stable oxide of uranium, UO 2 (s), both of which exist as UO 2 2+ in water. Among the eight different rice varieties investigated, Karnataka Ponni showed the maximum uranium uptake whereas unpolished Basmati rice showed the minimum. Interaction with other foodstuffs (potato, carrot, peas, kidney beans and lentils) with and without NaCl affected the extent of chemical interaction but was not consistent with the

Training manual for uranium mill workers on health protection from uranium

International Nuclear Information System (INIS)

McElroy, N.; Brodsky, A.

1986-01-01

This report provides information for uranium mill workers to help them understand the radiation safety aspects of working with uranium as it is processed from ore to yellowcake at the mills. The report is designed to supplement the radiation safety training provided by uranium mills to their workers. It is written in an easily readable style so that new employees with no previous experience working with uranium or radiation can obtain a basic understanding of the nature of radiation and the particular safety requirements of working with uranium. The report should be helpful to mill operators by providing training material to support their radiation safety training programs

Kinetics of the reduction of uranium oxide catalysts

International Nuclear Information System (INIS)

Heynen, H.W.G.; Camp-van Berkel, M.M.; Bann, H.S. van der

1977-01-01

The reduction of uranium oxide and uranium oxide on alumina catalysts by ethylbenzene and by hydrogen has been studied in a thermobalance. Ethylbenzene mole fractions between 0.0026 and 0.052 and hydrogen mole fractions between 0.1 and 0.6 were applied at temperatures of 425--530 0 C. During the reduction the uranium oxides are converted into UO 2 . The rate of reduction of pure uranium oxide appears to be constant in the composition region UO/sub 2.6/-UO/sub 2.25/. The extent of this region is independent of the concentration of the reducing agents and of the reaction temperature. The constant rate is explained in terms of a constant oxygen pressure which is in equilibrium with the two solid phases, U 3 O/sub 8-x/ and U 4 O 9 . The reduction rate is first order in hydrogen and zero order in ethylbenzene with activation energies of 120 and 190 kJ mol -1 , respectively. Oxygen diffusion through the lattice is probably not rate limiting. The reduction behavior of uranium oxide on alumina is different from that of pure uranium oxide; the rate of reduction continuously decreases with increasing degree of reduction. An explanation for this behavior has been given by visualizing this catalyst as a set of isolated uranium oxide crystallites with a relative wide variation of diameters, in an alumina matrix. At the beginning of the reduction, carbon dioxide and water are the only reaction products. Thereafter, benzene is found as well and, finally, at U/O ratios below 2.25, styrene also appears in the reactor outlet

Bacterial leaching of uranium ores - a review

International Nuclear Information System (INIS)

Lowson, R.T.

1975-11-01

The bacterial leaching of uranium ores involves the bacterially catalysed oxidation of associated pyrite to sulphuric acid and Fe 3+ by autotrophic bacteria and the leaching of the uranium by the resulting acidic, oxidising solution. Industrial application has been limited to Thiobacillus thiooxidans and Thiobacillus ferrooxidans at pH 2 to 3, and examples of these are described. The bacterial catalysis can be improved with nutrients or prevented with poisons. The kinetics of leaching are controlled by the bed depth, particle size, percolation rate, mineralogy and temperature. Current work is aimed at quantitatively defining the parameters controlling the kinetics and extending the method to alkaline conditions with other autotrophic bacteria. (author)

Uranium/plutonium and uranium/neptunium separation by the Purex process using hydroxyurea

International Nuclear Information System (INIS)

Zhu Zhaowu; He Jianyu; Zhang Zefu; Zhang Yu; Zhu Jianmin; Zhen Weifang

2004-01-01

Hydroxyurea dissolved in nitric acid can strip plutonium and neptunium from tri-butyl phosphate efficiently and has little influence on the uranium distribution between the two phases. Simulating the 1B contactor of the Purex process by hydroxyurea with nitric acid solution as a stripping agent, the separation factors of uranium/plutonium and uranium/neptunium can reach values as high as 4.7 x 10 4 and 260, respectively. This indicates that hydroxyurea is a promising salt free agent for uranium/plutonium and uranium/neptunium separations. (author)

Determination of uranium in uranium metal, uranium oxides, and uranyl nitrate solutions by potentiometric titration

International Nuclear Information System (INIS)

Tucker, H.L.; McElhaney, R.J.

1983-01-01

A simple, fast method for the determination of uranium in uranium metal, uranium oxides, and uranyl nitrate solutions has been adapted from the Davies-Gray volumetric method to meet the needs of Y-12. One-gram duplicate aliquots of uranium metal or uranium oxide are dissolved in 1:1 HNO 3 and concentrated H 2 SO 4 to sulfur trioxide fumes, and then diluted to 100-mL volume. Duplicate aliquots are then weighed for analysis. For uranyl nitrate samples, duplicate aliquots containing between 50 and 150 mg of U are weighed and analyzed directly. The weighed aliquot is transferred to a Berzelius beaker; 1.5 M sulfamic acid is added, followed in order by concentrated phosphoric acid, 1 M ferrous sulfate, and (after a 30-second interval) the oxidizing reagent. After a timed 3-minute waiting period, 100 mL of the 0.1% vanadyl sulfate-sulfuric acid mixture is added. The sample is then titrated past its endpoint with standard potassium dichromate, and the endpoint is determined by second derivative techniques on a mV/weight basis

Uranium from Seawater Program Review; Fuel Resources Uranium from Seawater Program DOE Office of Nuclear Energy

Energy Technology Data Exchange (ETDEWEB)

None

2013-07-01

the rate-limiting step of uranium uptake from seawater is also essential in designing an effective uranium recovery system. Finally, economic analyses have been used to guide these studies and highlight what parameters, such as capacity, recyclability, and stability, have the largest impact on the cost of extraction of uranium from seawater. Initially, the cost estimates by the JAEA for extraction of uranium from seawater with braided polymeric fibers functionalized with amidoxime ligands were evaluated and updated. The economic analyses were subsequently updated to reflect the results of this project while providing insight for cost reductions in the adsorbent development through “cradle-to-grave” case studies for the extraction process. This report highlights the progress made over the last three years on the design, synthesis, and testing of new materials to extract uranium for seawater. This report is organized into sections that highlight the major research activities in this project: (1) Chelate Design and Modeling, (2) Thermodynamics, Kinetics and Structure, (3) Advanced Polymeric Adsorbents by Radiation Induced Grafting, (4) Advanced Nanomaterial Adsorbents, (5) Adsorbent Screening and Modeling, (6) Marine Testing, and (7) Cost and Energy Assessment. At the end of each section, future research directions are briefly discussed to highlight the challenges that still remain to reduce the cost of extractions of uranium for seawater. Finally, contributions from the Nuclear Energy University Programs (NEUP), which complement this research program, are included at the end of this report.

Uranium: one utility's outlook

International Nuclear Information System (INIS)

Gass, C.B.

1983-01-01

The perspective of the Arizona Public Service Company (APS) on the uncertainty of uranium as a fuel supply is discussed. After summarizing the history of nuclear power and the uranium industries, a projection is made for the future uranium market. An uncrtain uranium market is attributed to various determining factors that include international politics, production costs, non-commercial government regulation, production-company stability, and questionable levels of uranium sales. APS offers its solutions regarding type of contract, choice of uranium producers, pricing mechanisms, and aids to the industry as a whole. 5 references, 10 figures, 1 table

Australian uranium today

International Nuclear Information System (INIS)

Fisk, B.

1978-01-01

The subject is covered in sections, entitled: Australia's resources; Northern Territory uranium in perspective; the government's decision [on August 25, 1977, that there should be further development of uranium under strictly controlled conditions]; Government legislation; outlook [for the Australian uranium mining industry]. (U.K.)

Solid state processing of massive uranium mononitride, using uranium and uranium higher nitride powders as starting materials (1962); Preparation a l'etat solide de mononitrure d'uranium massif a partir de poudres d'uranium et de nitrures superieurs d'uranium (1962)

Energy Technology Data Exchange (ETDEWEB)

Molinari, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1960-12-15

The mechanism and the optimum conditions for preparing uranium mononitride have been studied. The results have been used for hot pressing (250 kg/cm{sup 2}, 1000 deg. C, under vacuum) a mixture of powders of uranium and uranium higher nitrides. The products obtained have been identified by X-ray measurements and may be - at will and depending upon the stoichiometry - either UN, or a cermet a U{sub {alpha}}-UN. As revealed by the curved shape of grain boundaries, the sinters obtained here do not easily evolve towards physico-chemical equilibrium when submitted to heat treatment. This behaviour is quite different from the one observed with uranium monocarbide prepared by a similar method. This fact may be ascribed to the insolubility in the matrix UN of particles of UO{sub 2} being present as impurities. The density, hardness and thermal conductivity of these products are higher than those measured on uranium nitride or cermets U-UN obtained by other methods. (author) [French] Apres une etude prealable du mecanisme et des conditions optimales de nitruration de l'uranium, on a montre qu'il est possible de preparer par frittage sous charge (250 kg/cm{sup 2}, 1000 deg. C sous vide) d'un melange de poudres d'uranium et de nitrures superieurs d'uranium, un produit qui a ete identifie par diffraction de rayons X. On peut ainsi obtenir a volonte, soit le monocarbure UN, soit un cermet U{sub {alpha}}-UN dans le cas de compositions sous-stoechiometriques. Au contraire du monocarbure d'uranium prepare dans des conditions analogues, les produits obtenus ici, soumis a un traitement thermique, n'evoluent pas facilement vers un etat d'equilibre physico-chimique caracterise par l'existence de joints de grains rectilignes. On attribue ce phenomene a l'insolubilite de l'impurete UO{sub 2} dans UN. La densite, la durete, la conductibilite thermique de ces produits se revelent superieures a celles des nitrures d'uranium ou des cermets U-UN obtenus par les autres methodes. (auteur)

Bernabe Montano uranium deposit, Sandoval County

International Nuclear Information System (INIS)

Kozusko, R.G.; Saucier, A.E.

1980-01-01

Uranium mineralization was discovered on the Bernabe Montano Grant early in 1971. This old land grant, which is part of the Laguna Indian Reservation, is approximately 25 mile northwest of Albuquerque, New Mexico. About 2,000 holes have been drilled on this property to date, and an ore reserve of 10 to 20 million lbs of uranium oxide has been delineated in the Westwater Canyon Member of the Morrison Formation. The mineralization consists of multiple, stacked blankets of mineralized humate which appear to be localized in an area of slightly thicker and more laterally continuous sandstones. The blankets occur along a relatively straight mineral trend about a half mile wide and several miles in length. Holes drilled on-trend usually encounter gamma anomalies, whereas holes drilled off-trend are barren. The uranium is believed to have been carried through the Westwater Canyon Member by ground water that followed the palochannel systems shortly after burial in Late Jurassic time. This discovery once again confirms the trend-ore concept, and it probably represents the present eastern economic limit of the Grants mineral belt. The orebody is unusual because it occurs in a structurally deformed area called the Rio Puerco fault zone. The mineralization, which does not conform to a roll-front model, represents an important addition to the ore reserves of the Grants uranium region

Removal of uranium from uranium-contaminated soils -- Phase 1: Bench-scale testing. Uranium in Soils Integrated Demonstration

Energy Technology Data Exchange (ETDEWEB)

Francis, C. W.

1993-09-01

To address the management of uranium-contaminated soils at Fernald and other DOE sites, the DOE Office of Technology Development formed the Uranium in Soils Integrated Demonstration (USID) program. The USID has five major tasks. These include the development and demonstration of technologies that are able to (1) characterize the uranium in soil, (2) decontaminate or remove uranium from the soil, (3) treat the soil and dispose of any waste, (4) establish performance assessments, and (5) meet necessary state and federal regulations. This report deals with soil decontamination or removal of uranium from contaminated soils. The report was compiled by the USID task group that addresses soil decontamination; includes data from projects under the management of four DOE facilities [Argonne National Laboratory (ANL), Los Alamos National Laboratory (LANL), Oak Ridge National Laboratory (ORNL), and the Savannah River Plant (SRP)]; and consists of four separate reports written by staff at these facilities. The fundamental goal of the soil decontamination task group has been the selective extraction/leaching or removal of uranium from soil faster, cheaper, and safer than current conventional technologies. The objective is to selectively remove uranium from soil without seriously degrading the soil`s physicochemical characteristics or generating waste forms that are difficult to manage and/or dispose of. Emphasis in research was placed more strongly on chemical extraction techniques than physical extraction techniques.

Determination of uranium and its isotopic ratios in environmental samples

International Nuclear Information System (INIS)

Flues Szeles, M.S.M.

1990-01-01

A method for the determination of uranium and its isotopic ratios ( sup(235)U/ sup(238)U and sup(234U/ sup(238)U) is established in the present work. The method can be applied in environmental monitoring programs of uranium enrichment facilities. The proposed method is based on the alpha spectrometry technique which is applied after a purification of the sample by using an ionic exchange resin. The total yield achieved was (91 + 5)% with a precision of 5%, an accuracy of 8% and a lower limit of detection of 7,9 x 10 sup(-4)Bq. The uranium determination in samples containing high concentration of iron, which is an interfering element present in environmental samples, particularly in soil and sediment, was also studied. The results obtained by using artificial samples containing iron and uranium in the ratio 1000:1, were considered satisfactory. (author)

Sandstone-type uranium deposits

International Nuclear Information System (INIS)

Austin, S.R.; D'Andrea, R.F. Jr.

1978-01-01

Three overall factors are necessary for formation of uranium deposits in sandstone: a source of uranium, host rocks capable of transmitting uranium-bearing solutions, and a precipitant. Possible sources of uranium in sandstone-type deposits include groundwaters emanating from granitic highlands, arkosic sediments, tuffaceous material within or overlying the host rocks, connate fluids, and overlying black shales. The first three sources are considered the most likely. Host rocks are generally immature sandstones deposited in alluvial-fan, intermontane-basin or marginal-marine environments, but uranium deposits do occur in well-winnowed barrier-bar or eolian sands. Host rocks for uranium deposits generally show coefficients of permeability on the order of 1 to 100 gal/day/ft 2 . Precipitants are normally agents capable of reducing uranium from the uranyl to the uranous state. The association of uranium with organic matter is unequivocal; H 2 S, a powerful reductant, may have been present at the time of formation of some deposits but may go unnoticed today. Vanadium can serve to preserve the tabular characteristics of some deposits in the near-surface environment, but is considered an unlikely primary precipitant for uranium. Uranium deposits in sandstone are divided into two overall types: peneconcordant deposits, which occur in locally reducing environments in otherwise oxidized sandstones; and roll-type deposits, which occur at the margin of an area where an oxidized groundwater has permeated an otherwise reduced sandstone. Uranium deposits are further broken down into four subclasses; these are described