WorldWideScience

Sample records for rf communication systems

  1. An RF tag communication system model for noise radar

    Science.gov (United States)

    Pan, Qihe; Narayanan, Ram M.

    2008-04-01

    RF (radio-frequency) tags have drawn increasing research interest because of their great potential uses in many radio frequency identification applications. They can also be configured to work with radar as a communication channel by receiving radar acquisition signals, suitably coding these, and retransmitting them back to the radar. This paper proposes a system model for the communication between a noise radar and multiple RF tags. The radar interrogates the RF tags in a region of interest by sending ultrawideband noise signals. Upon receiving the radar's signal, all the tags within the radar's range wake up, and respond to the radar with simple messages. The RF tag filters the radar signal to a unique spectral band, which represents its identification information, and different RF tags occupy different non-overlapping bands of the spectrum of the radar signal. Tag messages are modulated onto the waveform through taps of weighted delays. The radar decodes the RF tag identifications and corresponding messages by cross-correlating the RF tag returned signals with the replica of the radar transmitted signal. Calculations and simulation results both show that the proposed system is capable of communicating simple messages between RF tags and radar.

  2. An Orbiting Standards Platform for communication satellite system RF measurements

    Science.gov (United States)

    Wallace, R. G.; Woodruff, J. J.

    1978-01-01

    The Orbiting Standards Platform (OSP) is a proposed satellite dedicated to performing RF measurements on space communications systems. It would consist of a quasi-geostationary spacecraft containing an ensemble of calibrated RF sources and field strength meters operating in several microwave bands, and would be capable of accurately and conveniently measuring critical earth station and satellite RF performance parameters, such as EIRP, gain, figure of merit (G/T), crosspolarization, beamwidth, and sidelobe levels. The feasibility and utility of the OSP concept has been under joint study by NASA, NBS, Comsat and NTIA. A survey of potential OSP users was conducted by NTIA as part of this effort. The response to this survey, along with certain trends in satellite communications system design, indicates a growing need for such a measurement service.

  3. RF MEMS and Their Applications in NASA's Space Communication Systems

    Science.gov (United States)

    Williams, W. Daniel; Ponchak, George E.; Simons, Rainee N.; Zaman, Afroz; Kory, Carol; Wintucky, Edwin; Wilson, Jeffrey D.; Scardelletti, Maximilian; Lee, Richard; Nguyen, Hung

    2001-01-01

    Radio frequency (RF) and microwave communication systems rely on frequency, amplitude, and phase control circuits to efficiently use the available spectrum. Phase control circuits are required for electronically scanning phase array antennas that enable radiation pattern shaping, scanning, and hopping. Two types of phase shifters, which are the phase control circuits, are most often used. The first is comprised of two circuits with different phase characteristics such as two transmission lines of different lengths or a high pass and low pass filter and a switch that directs the RF power through one of the two circuits. Alternatively, a variable capacitor, or varactor, is used to change the effective electrical path length of a transmission line, which changes the phase characteristics. Filter banks are required for the diplexer at the front end of wide band communication satellites. These filters greatly increase the size and mass of the RF/microwave systems, but smaller diplexers may be made with a low loss varactor or a group of capacitors, a switch and an inductor.

  4. FinFET and UTBB for RF SOI communication systems

    Science.gov (United States)

    Raskin, Jean-Pierre

    2016-11-01

    Performance of RF integrated circuit (IC) is directly linked to the analog and high frequency characteristics of the transistors, the quality of the back-end of line process as well as the electromagnetic properties of the substrate. Thanks to the introduction of the trap-rich high-resistivity Silicon-on-Insulator (SOI) substrate on the market, the ICs requirements in term of linearity are fulfilled. Today partially depleted SOI MOSFET is the mainstream technology for RF SOI systems. Future generations of mobile communication systems will require transistors with better high frequency performance at lower power consumption. The advanced MOS transistors in competition are FinFET and Ultra Thin Body and Buried oxide (UTBB) SOI MOSFETs. Both devices have been intensively studied these last years. Most of the reported data concern their digital performance. In this paper, their analog/RF behavior is described and compared. Both show similar characteristics in terms of transconductance, Early voltage, voltage gain, self-heating issue but UTBB outperforms FinFET in terms of cutoff frequencies thanks to their relatively lower fringing parasitic capacitances.

  5. Accurate measurement of RF exposure from emerging wireless communication systems

    Science.gov (United States)

    Letertre, Thierry; Monebhurrun, Vikass; Toffano, Zeno

    2013-04-01

    Isotropic broadband probes or spectrum analyzers (SAs) may be used for the measurement of rapidly varying electromagnetic fields generated by emerging wireless communication systems. In this paper this problematic is investigated by comparing the responses measured by two different isotropic broadband probes typically used to perform electric field (E-field) evaluations. The broadband probes are submitted to signals with variable duty cycles (DC) and crest factors (CF) either with or without Orthogonal Frequency Division Multiplexing (OFDM) modulation but with the same root-mean-square (RMS) power. The two probes do not provide accurate enough results for deterministic signals such as Worldwide Interoperability for Microwave Access (WIMAX) or Long Term Evolution (LTE) as well as for non-deterministic signals such as Wireless Fidelity (WiFi). The legacy measurement protocols should be adapted to cope for the emerging wireless communication technologies based on the OFDM modulation scheme. This is not easily achieved except when the statistics of the RF emission are well known. In this case the measurement errors are shown to be systematic and a correction factor or calibration can be applied to obtain a good approximation of the total RMS power.

  6. Advances in analog and RF IC design for wireless communication systems

    CERN Document Server

    Manganaro, Gabriele

    2013-01-01

    Advances in Analog and RF IC Design for Wireless Communication Systems gives technical introductions to the latest and most significant topics in the area of circuit design of analog/RF ICs for wireless communication systems, emphasizing wireless infrastructure rather than handsets. The book ranges from very high performance circuits for complex wireless infrastructure systems to selected highly integrated systems for handsets and mobile devices. Coverage includes power amplifiers, low-noise amplifiers, modulators, analog-to-digital converters (ADCs) and digital-to-analog converters

  7. Communication methods, systems, apparatus, and devices involving RF tag registration

    Science.gov (United States)

    Burghard, Brion J.; Skorpik, James R.

    2008-04-22

    One technique of the present invention includes a number of Radio Frequency (RF) tags that each have a different identifier. Information is broadcast to the tags from an RF tag interrogator. This information corresponds to a maximum quantity of tag response time slots that are available. This maximum quantity may be less than the total number of tags. The tags each select one of the time slots as a function of the information and a random number provided by each respective tag. The different identifiers are transmitted to the interrogator from at least a subset of the RF tags.

  8. Optimal Design of Dual-Hop VLC/RF Communication System With Energy Harvesting

    KAUST Repository

    Rakia, Tamer

    2016-07-28

    In this letter, we consider a dual-hop heterogeneous visible light communication (VLC)/radio frequency (RF) communication system to extend the coverage of VLC systems. Besides detecting the information over VLC link, the relay is able to harvest energy from the first-hop VLC link, by extracting the direct current component of the received optical signal, and uses the harvested energy to retransmit the data to a mobile terminal over the second-hop RF link. We investigate the optimal design of the hybrid system in terms of data rate maximization.

  9. Bandwidth utilization maximization of scientific RF communication systems

    Energy Technology Data Exchange (ETDEWEB)

    Rey, D. [Sandia National Lab., Albuquerque, NM (United States); Ryan, W. [New Mexico State Univ., Las Cruces, NM (United States); Ross, M.

    1997-01-01

    A method for more efficiently utilizing the frequency bandwidth allocated for data transmission is presented. Current space and range communication systems use modulation and coding schemes that transmit 0.5 to 1.0 bits per second per Hertz of radio frequency bandwidth. The goal in this LDRD project is to increase the bandwidth utilization by employing advanced digital communications techniques. This is done with little or no increase in the transmit power which is usually very limited on airborne systems. Teaming with New Mexico State University, an implementation of trellis coded modulation (TCM), a coding and modulation scheme pioneered by Ungerboeck, was developed for this application and simulated on a computer. TCM provides a means for reliably transmitting data while simultaneously increasing bandwidth efficiency. The penalty is increased receiver complexity. In particular, the trellis decoder requires high-speed, application-specific digital signal processing (DSP) chips. A system solution based on the QualComm Viterbi decoder and the Graychip DSP receiver chips is presented.

  10. Concurrent System Engineering and Risk Reduction for Dual-Band (RF/optical) Spacecraft Communications

    Science.gov (United States)

    Fielhauer, Karl, B.; Boone, Bradley, G.; Raible, Daniel, E.

    2012-01-01

    This paper describes a system engineering approach to examining the potential for combining elements of a deep-space RF and optical communications payload, for the purpose of reducing the size, weight and power burden on the spacecraft and the mission. Figures of merit and analytical methodologies are discussed to conduct trade studies, and several potential technology integration strategies are presented. Finally, the NASA Integrated Radio and Optical Communications (iROC) project is described, which directly addresses the combined RF and optical approach.

  11. MEMS technologies for rf communications

    Science.gov (United States)

    Wu, Qun; Kim, B. K.

    2001-04-01

    Microelectromechanical system (MEMS) represents an exciting new technology derived from the same fabricating processes used to make integrated circuits. The trends of growing importance of the wireless communications market is toward the system with minimal size, cost and power consumption. For the purpose of MEMS R&D used for wireless communications, a history and present situation of MEMS device development are reviewed in this paper, and an overview of MEMS research topics on RF communication applications and the state of the art technologies are also presented here.

  12. Single-chip RF communications systems in CMOS

    DEFF Research Database (Denmark)

    Olesen, Ole

    1997-01-01

    The paper describes the state of the art of the Nordic mobile communication project ConFront. This is a cooperation project with 3 Nordic universities and local industry. The ultimate goal is to make a CMOS one-chip mobile phone.......The paper describes the state of the art of the Nordic mobile communication project ConFront. This is a cooperation project with 3 Nordic universities and local industry. The ultimate goal is to make a CMOS one-chip mobile phone....

  13. Impact of RF Imperfections on 60 GHz Wireless Communication Systems

    NARCIS (Netherlands)

    Rizvi, U.H.

    2011-01-01

    Over the last couple of decades, wireless communication has proved to be a phenomenal success and has generated a booming industry with over 5 billion mobile handsets in use worldwide. This has on one end eased the life of its users while on the other end has introduced new challenges for wireless s

  14. Adaptation of Hybrid FSO/RF Communication System Using Puncturing Technique

    Directory of Open Access Journals (Sweden)

    M. N. Khan

    2016-12-01

    Full Text Available Spectrum of radio frequency (RF communications is limited and expensive to install new applications. Free space optical (FSO communication is a viable technology which offers enormous bandwidth, license free installation, inexpensive deployment and error prone links. The FSO links degrade significantly due to the varying atmospheric and weather conditions (fog, cloud, snow, haze and combination of these. We propose a hybrid FSO/RF communication system which adapts the varying nature of atmosphere and weather. For the adaption of varying atmosphere and weather scenarios, we develop a novel optimization algorithm. The proposed algorithm is based on the well-known puncturing technique. We provide an extrinsic information transfer (EXIT chart for the binary and quaternary mapping scheme for the proposed communication system. We simulate the proposed algorithm for the hybrid communication system and analyze the system performance. The proposed algorithm is computationally less expensive and provide better performance gains over varying atmosphere and weather conditions. The algorithm is suitable for fast speed applications.

  15. Experimental evaluation of a radio-on-FSO communication system for multiple RF signal transmission

    Science.gov (United States)

    Kazaura, Kamugisha; Dat, Pham; Bekkali, Abdelmoula; Shah, Alam; Suzuki, Toshiji; Wakamori, Kazuhiko; Matsumoto, Mitsuji; Nakamura, Takuya; Takahashi, Koichi; Higashino, Takeshi; Aburakawa, Yuji; Tsukamoto, Katsutoshi; Komaki, Shozo

    2009-02-01

    In this paper we present the design concept plus experimental results and evaluation of a newly developed advanced DWDM Radio-on-Free-Space Optical (RoFSO) communication system capable of simultaneous transmission of multiple RF signals. The RoFSO system is evaluated based on the performance metric parameters defined for the various RF signals comprising of different wireless services including terrestrial digital broadcasting signals, cellular 3GPP W-CDMA signals, IEEE 802.11 WLAN based signals etc being transmitted over the RoFSO link. The performance metric parameters being considered include standard optical received power, CNR and BER characteristics, W-CDMA signal transmission metric parameters like Adjacent Channel Leakage Ratio (ACLR) and Error Vector Magnitude (EVM), modulation error ratio (MER) for digital terrestrial television broadcasting signals as well as spectrum mask and EVM for IEEE 802.11 Wireless LAN signal transmission.

  16. Application of wavelets to image coding in an rf-link communication system

    Science.gov (United States)

    Liou, C. S. J.; Conners, Gary H.; Muczynski, Joe

    1995-04-01

    The joint University of Rochester/Rochester Institute of Technology `Center for Electronic Imaging Systems' (CEIS) is designed to focus on research problems of interest to industrial sponsors, especially the Rochester Imaging Consortium. Compression of tactical images for transmission over an rf link is an example of this type of research project which is being worked on in collaboration with one of the CEIS sponsors, Harris Corporation/RF Communications. The Harris digital video imagery transmission system (DVITS) is designed to fulfill the need to transmit secure imagery between unwired locations at real-time rates. DVITS specializes in transmission systems for users who rely on hf equipment operating at the low end of the frequency spectrum. However, the inherently low bandwidth of hf combined with transmission characteristics such as fading and dropout severely restrict the effective throughput. The problem at designing a system such as DVITS is particularly challenging because of bandwidth and signal/noise limitations, and because of the dynamic nature of the operational environment. In this paper, a novel application of wavelets in tactical image coding is proposed to replace the current DCT compression algorithm in the DVITS system. THe effects of channel noise on the received image are determined and various design strategies combining image segmentation, compression, and error correction are described.

  17. Short-range wireless communication fundamentals of RF system design and application

    CERN Document Server

    Bensky, Alan

    2004-01-01

    The Complete "Tool Kit” for the Hottest Area in RF/Wireless Design!Short-range wireless-communications over distances of less than 100 meters-is the most rapidly growing segment of RF/wireless engineering. Alan Bensky is an internationally recognized expert in short-range wireless, and this new edition of his bestselling book is completely revised to cover the latest developments in this fast moving field.You'll find coverage of such cutting-edge topics as: architectural trends in RF/wireless integrated circuits compatibility and conflict issues between differen

  18. RF Transceiver Design for MIMO Wireless Communications

    CERN Document Server

    Mohammadi, Abbas

    2012-01-01

    This practical resource offers a thorough examination of RF transceiver design for MIMO communications.  Offering a practical view on MIMO wireless systems, this book extends fundamental concepts on classic wireless transceiver design techniques to MIMO transceivers. This helps reader gain a very comprehensive understanding of the subject. This in-depth volume describes many theoretical and implementation challenges on MIMO transceivers and provides the practical solutions for these issues. This comprehensive book provides thorough descriptions of MIMO theoretical concepts, MIMO single carrier and OFDM modulation, RF transceiver design concepts, power amplifier, MIMO transmitter design techniques and their RF impairments, MIMO receiver design methods, RF impairments study including nonlinearity, DC-offset, I/Q imbalance and phase noise and their compensation in OFDM and MIMO techniques. In addition, it provides the most practical techniques to realize RF front-ends in MIMO systems. This book is supported wit...

  19. Software Defined Electronics: A Revolutionary Change in Design and Teaching Paradigm of RF Radio Communications Systems

    Directory of Open Access Journals (Sweden)

    Géza Kolumbán

    2015-06-01

    Full Text Available Band-pass signals are used everywhere in radio communications. The band-pass property makes the substitution of each RF/microwave/ optical analog signal processing possible with a low-frequency digital one in Software Defined Electronics (SDE. In SDE, the high frequency band-pass signals are transformed into the BaseBand (BB by a universal HW device and every application is implemented in BB, entirely in software. SDE concept uses (i the lowest sampling rate attainable theoretically and (ii the same universal HW device in every application. The huge level of flexibility offered by the SW implementation is essential in many applications from cognitive radio to adaptive reconfigurable systems. This tutorial, written for interested readers who have no solid background in software defined radio, virtual instrumentation and SoC technology, surveys the SDE theory, uses a step-by-step approach for the derivation of BB equivalents and demonstrates the application of SDE concept in scientific research, prototyping and education.

  20. Above-IC RF MEMS devices for communication applications

    OpenAIRE

    Fritschi, Raphaël

    2007-01-01

    Wireless communications are showing an explosive growth in emerging consumer and military applications of radiofrequency (RF), microwave, and millimeter-wave circuits and systems. Applications include wireless personal connectivity (Bluetooth), wireless local area networks (WLAN), mobile communication systems (GSM, GPRS, UMTS, CDMA), satellite communications and automotive electronics. Future cell phones and ground communication systems as well as communication satellites will require more an...

  1. Above-IC RF MEMS devices for communication applications

    OpenAIRE

    Fritschi, Raphaël; Ionescu, Mihai Adrian; Flückiger, Philippe

    2008-01-01

    Wireless communications are showing an explosive growth in emerging consumer and military applications of radiofrequency (RF), microwave, and millimeter-wave circuits and systems. Applications include wireless personal connectivity (Bluetooth), wireless local area networks (WLAN), mobile communication systems (GSM, GPRS, UMTS, CDMA), satellite communications and automotive electronics. Future cell phones and ground communication systems as well as communication satellites will require more an...

  2. RF/optical shared aperture for high availability wideband communication RF/FSO links

    Energy Technology Data Exchange (ETDEWEB)

    Ruggiero, Anthony J; Pao, Hsueh-yuan; Sargis, Paul

    2014-04-29

    An RF/Optical shared aperture is capable of transmitting and receiving optical signals and RF signals simultaneously. This technology enables compact wide bandwidth communications systems with 100% availability in clear air turbulence, rain and fog. The functions of an optical telescope and an RF reflector antenna are combined into a single compact package by installing an RF feed at either of the focal points of a modified Gregorian telescope.

  3. RF/optical shared aperture for high availability wideband communication RF/FSO links

    Energy Technology Data Exchange (ETDEWEB)

    Ruggiero, Anthony J; Pao, Hsueh-yuan; Sargis, Paul

    2015-03-24

    An RF/Optical shared aperture is capable of transmitting and receiving optical signals and RF signals simultaneously. This technology enables compact wide bandwidth communications systems with 100% availability in clear air turbulence, rain and fog. The functions of an optical telescope and an RF reflector antenna are combined into a single compact package by installing an RF feed at either of the focal points of a modified Gregorian telescope.

  4. Signal Processing for Wireless Communication MIMO System with Nano- Scaled CSDG MOSFET based DP4T RF Switch.

    Science.gov (United States)

    Srivastava, Viranjay M

    2015-01-01

    In the present technological expansion, the radio frequency integrated circuits in the wireless communication technologies became useful because of the replacement of increasing number of functions, traditional hardware components by modern digital signal processing. The carrier frequencies used for communication systems, now a day, shifted toward the microwave regime. The signal processing for the multiple inputs multiple output wireless communication system using the Metal- Oxide-Semiconductor Field-Effect-Transistor (MOSFET) has been done a lot. In this research the signal processing with help of nano-scaled Cylindrical Surrounding Double Gate (CSDG) MOSFET by means of Double- Pole Four-Throw Radio-Frequency (DP4T RF) switch, in terms of Insertion loss, Isolation, Reverse isolation and Inter modulation have been analyzed. In addition to this a channel model has been presented. Here, we also discussed some patents relevant to the topic.

  5. Radio Frequency (RF) Micro-Electromechanical Systems (MEMS) Switches for Space Communications

    Science.gov (United States)

    Simons, Rainee N.; Ponchak, George E.; Scardelletti, Maximillian C.; Varaljay, Nicholas C.

    2000-01-01

    Micro-electromechanical systems (MEMS) is an emerging technology for radio frequency (RF) systems because it has the potential to dramatically decrease loss and improve efficiency. In this paper, we address the design and fabrication of novel MEMS switches being developed at NASA Glenn Research Center. Two types of switches are being developed: a microstrip series single pole single throw (SPST) switch and a coplanar waveguide (CPW) series SPST and single pole double throw (SPDT) switches. These are being fabricated as an integral part of 50 Ohm microstrip and CPW RF integrated circuits using microfabrication techniques. The construction of the switch relies on a cantilever beam that is partially supported by a dielectric post. The cantilever beam is electro-magnetically actuated. To decrease stiction, a Si3N4 thin film is deposited over the contact area. Thus, when the switch is closed, the ON-state insertion loss is governed by the parallel plate capacitance formed by the two contacts. The isolation in the OFF-state is governed by the parasitic capacitance when the cantilever is in the up position. RF MEMS switches have been demonstrated with 80% lower insertion loss than conventional solid state devices (GaAs Metal Semiconductor Field Effect Transistors (MESFETs) and Silicon PIN diodes) based switches. For example, a conventional GaAs five-bit phase shifter which is required for beam steering in a phased array antenna has approximately 7 dB of insertion loss at 26.5 GHz where as a comparable MEMS based phase shifter is expected to have only 2 dB of insertion loss. This translates into 56% lower power dissipation and therefore decreases the thermal load on the spacecraft and also reduces the power amplifier requirements. These benefits will enable NASA to build the next generation of deep space science crafts and micro/nano satellites.

  6. Novel RF and microwave components employing ferroelectric and solid-state tunable capacitors for multi-functional wireless communication systems

    Science.gov (United States)

    Tombak, Ali

    The recent advancement in wireless communications demands an ever increasing improvement in the system performance and functionality with a reduced size and cost. This thesis demonstrates novel RF and microwave components based on ferroelectric and solid-state based tunable capacitor (varactor) technologies for the design of low-cost, small-size and multi-functional wireless communication systems. These include tunable lumped element VHF filters based on ferroelectric varactors, a beam-steering technique which, unlike conventional systems, does not require separate power divider and phase shifters, and a predistortion linearization technique that uses a varactor based tunable R-L-C resonator. Among various ferroelectric materials, Barium Strontium Titanate (BST) is actively being studied for the fabrication of high performance varactors at RF and microwave frequencies. BST based tunable capacitors are presented with typical tunabilities of 4.2:1 with the application of 5 to 10 V DC bias voltages and typical loss tangents in the range of 0.003--0.009 at VHF frequencies. Tunable lumped element lowpass and bandpass VHF filters based on BST varactors are also demonstrated with tunabilities of 40% and 57%, respectively. A new beam-steering technique is developed based on the extended resonance power dividing technique. Phased arrays based on this technique do not require separate power divider and phase shifters. Instead, the power division and phase shifting circuits are combined into a single circuit, which utilizes tunable capacitors. This results in a substantial reduction in the circuit complexity and cost. Phased arrays based on this technique can be employed in mobile multimedia services and automotive collision avoidance radars. A 2-GHz 4-antenna and a 10-GHz 8-antenna extended resonance phased arrays are demonstrated with scan ranges of 20 degrees and 18 degrees, respectively. A new predistortion linearization technique for the linearization of RF

  7. Wireless Communication Electronics Introduction to RF Circuits and Design Techniques

    CERN Document Server

    Sobot, Robert

    2012-01-01

    This book is intended for senior undergraduate and graduate students as well as practicing engineers who are involved in design and analysis of radio frequency (RF) circuits.  Detailed tutorials are included on all major topics required to understand fundamental principles behind both the main sub-circuits required to design an RF transceiver and the whole communication system. Starting with review of fundamental principles in electromagnetic (EM) transmission and signal propagation, through detailed practical analysis of RF amplifier, mixer, modulator, demodulator, and oscillator circuit topologies, all the way to the system communication theory behind the RF transceiver operation, this book systematically covers all relevant aspects in a way that is suitable for a single semester university level course.   Offers readers a complete, self-sufficient tutorial style textbook; Includes all relevant topics required to study and design an RF receiver in a consistent, coherent way with appropriate depth for a on...

  8. Design for short-range wireless communication system based on chip nRF24L01%基于nRF24L01芯片的近程无线通信系统设计

    Institute of Scientific and Technical Information of China (English)

    李贺; 程祥; 曾令国

    2014-01-01

    介绍一种基于STC89C52单片机、STM32系列MCU和无线射频收发芯片nRF24L01的无线通信系统设计,描述了nRF24L01的主要引脚特性、具体应用、SPI指令,详细阐述了在Enhanced ShockBurst模式下的配置方法,同时给出了根据nRF24L01的SPI时序用通用IO口模拟SPI接口和配置STM32系列MCU硬件SPI接口的详细说明。%Design for a wireless communication system based on STC89C52,MCU in STM32F103 series and wireless RF transcieving chip nRF24L01 is introduced in this paper. The main pin characteristics,concrete applications and SPI instructions are described. The configuration method in Enhanced ShockBurst mode is elaborated. The metnods to simulate SPI by using the general IO interface according to SPI time sequence of nRF24L01and configure STM32 hardware SPI are given.

  9. 基于nRF24L01的短距离无线通信系统%A Short-Distance Wireless Communication System Based on nRF24L01

    Institute of Scientific and Technical Information of China (English)

    张娟; 陆欣云

    2012-01-01

    This paper introduces a kind of short-distance wireless communication system based on nRF24LO1 wireless chip, and a cluster-network data transmission system which consists of nRF24L01 (2.4 GHz radio frequency chips) and low-power single-chip MSP430F449. The node of the wireless communication system works in collaboration with a hardware platform whose core is MCU. Data are transmitted based on the agreed protocol. The data can be displayed on LED displayer after data processing of background equipment is monitored by PC.%介绍一种基于nRF24L01无线芯片的短距离无线通信系统,以nRF24L01(2.4GHz无线射频芯片)和低功耗单片机MSP430F449为核心组成的簇形网络数据传输系统.无线通信系统的节点依靠MCU为核心的硬件平台协同工作,按照约定好的协议实现数据传输,经过Pc机监控设备后台的数据处理,使得数据在LED显示屏上显示.

  10. LANSCE RF System Refurbishment

    CERN Document Server

    Rees, Daniel; Kwon, Sung-il; Lyles, John T M; Lynch, Michael; Prokop, Mark; Reass, William; Tallerico, Paul J

    2005-01-01

    The Los Alamos Neutron Science Center (LANSCE) is in the planning phase of a refurbishment project that will sustain reliable facility operations well into the next decade. The LANSCE accelerator was constructed in the late 1960s and early 1970s and is a national user facility that provides pulsed protons and spallation neutrons for defense and civilian research and applications. We will be replacing all the 201 MHz RF systems and a substantial fraction of the 805 MHz RF systems and high voltage systems. The current 44 LANSCE 805 MHz, 1.25 MW klystrons have an average in-service time in excess of 110,000 hours. All 44 must be in service to operate the accelerator. There are only 9 spares left. The klystrons receive their DC power from the power system originally installed in 1960. Although this power system has been extremely reliable, gas analysis of the insulating oil is indicating age related degradation that will need attention in the next few years. This paper will provide the design details of the new R...

  11. Hybrid Ground Station Technology for RF and Optical Communication Links

    Science.gov (United States)

    Davarian, Faramaz; Hoppe, D.; Charles, J.; Vilnrotter, V.; Sehic, A.; Hanson, T.; Gam, E.

    2012-01-01

    To support future enhancements of NASA's deep space and planetary communications and tracking services, the Jet Propulsion Laboratory is developing a hybrid ground station that will be capable of simultaneously supporting RF and optical communications. The main reason for adding optical links to the existing RF links is to significantly increase the capacity of deep space communications in support of future solar system exploration. It is envisioned that a mission employing an optical link will also use an RF link for telemetry and emergency purposes, hence the need for a hybrid ground station. A hybrid station may also reduce operations cost by requiring fewer staff than would be required to operate two stations. A number of approaches and techniques have been examined. The most promising ones have been prototyped for field examination and validation.

  12. NSLS-II RF SYSTEMS

    Energy Technology Data Exchange (ETDEWEB)

    Rose, J.; Gash, W.; Holub, B.; Kawashima, Y.; Ma, H.; Towne, N.; Yeddulla, M.

    2011-03-28

    The NSLS-II is a new third generation light source being constructed at Brookhaven Lab. The storage ring is optimized for low emittance by use of damping wigglers to reduce the emittance to below 1 nm-rad. The RF systems are designed to provide stable beam through tight RF phase and amplitude stability requirements.

  13. RF MEMS Switches for Mobile Communication

    NARCIS (Netherlands)

    Steeneken, Peter; Herfst, Rodolf; Suy, Hilco; Goossens, Martijn; Beek, van Joost; Bielen, Jeroen; Stulemeijer, Jiri; Schmitz, Jurriaan

    2008-01-01

    Switched capacitors based on radio frequency microelectromechanical systems (RF MEMS) can enable a breakthrough in radio technology. Their switching principle is based on the mechanical movement of the plates of a parallel plate capacitor using the electrostatic force. The resulting difference in ca

  14. Automatic calorimetry system monitors RF power

    Science.gov (United States)

    Harness, B. W.; Heiberger, E. C.

    1969-01-01

    Calorimetry system monitors the average power dissipated in a high power RF transmitter. Sensors measure the change in temperature and the flow rate of the coolant, while a multiplier computes the power dissipated in the RF load.

  15. SPS RF System a Tetrode

    CERN Multimedia

    1974-01-01

    The main RF-system of the SPS comprises four cavities: two of 20 m length and two of 16.5 m length. They are all installed in one long straight section (LSS 3). These cavities are of the travelling-wave type operating at a centre frequency of 200.2 MHz. They are wideband, filling time about 700 ns and untuned. The power amplifiers, using tetrodes are installed in a surface building 200 m from the cavities. Initially only two cavities were installed, a third cavity was installed in 1978 and a forth one in 1979. The number of power amplifiers was also gradually increased: by end 1980 there were 8 500 kW units combined in pairs to feed each of the 4 cavities with up to about 1 MW RF power, resulting in a total accelerating voltage of about 8 MV. See also 7412016X, 7412017X, 7411048X.

  16. Protection of Accelerator Hardware: RF systems

    CERN Document Server

    Kim, S-H

    2016-01-01

    The radio-frequency (RF) system is the key element that generates electric fields for beam acceleration. To keep the system reliable, a highly sophisticated protection scheme is required, which also should be designed to ensure a good balance between beam availability and machine safety. Since RF systems are complex, incorporating high-voltage and high-power equipment, a good portion of machine downtime typically comes from RF systems. Equipment and component damage in RF systems results in long and expensive repairs. Protection of RF system hardware is one of the oldest machine protection concepts, dealing with the protection of individual high-power RF equipment from breakdowns. As beam power increases in modern accelerators, the protection of accelerating structures from beam-induced faults also becomes a critical aspect of protection schemes. In this article, an overview of the RF system is given, and selected topics of failure mechanisms and examples of protection requirements are introduced.

  17. Low jitter RF distribution system

    Science.gov (United States)

    Wilcox, Russell; Doolittle, Lawrence; Huang, Gang

    2012-09-18

    A timing signal distribution system includes an optical frequency stabilized laser signal amplitude modulated at an rf frequency. A transmitter box transmits a first portion of the laser signal and receive a modified optical signal, and outputs a second portion of the laser signal and a portion of the modified optical signal. A first optical fiber carries the first laser signal portion and the modified optical signal, and a second optical fiber carries the second portion of the laser signal and the returned modified optical signal. A receiver box receives the first laser signal portion, shifts the frequency of the first laser signal portion outputs the modified optical signal, and outputs an electrical signal on the basis of the laser signal. A detector at the end of the second optical fiber outputs a signal based on the modified optical signal. An optical delay sensing circuit outputs a data signal based on the detected modified optical signal. An rf phase detect and correct signal circuit outputs a signal corresponding to a phase stabilized rf signal based on the data signal and the frequency received from the receiver box.

  18. Short range RF communication for jet engine control

    Science.gov (United States)

    Sexton, Daniel White (Inventor); Hershey, John Erik (Inventor)

    2007-01-01

    A method transmitting a message over at least one of a plurality of radio frequency (RF) channels of an RF communications network is provided. The method comprises the steps of detecting a presence of jamming pulses in the at least one of the plurality of RF channels. The characteristics of the jamming pulses in the at least one of the plurality of RF channels is determined wherein the determined characteristics define at least interstices between the jamming pulses. The message is transmitted over the at least one of the plurality of RF channels wherein the message is transmitted within the interstices of the jamming pulse determined from the step of determining characteristics of the jamming pulses.

  19. RF and microwave engineering fundamentals of wireless communications

    CERN Document Server

    Gustrau, Frank

    2012-01-01

    This book provides a fundamental and practical introduction to radio frequency and microwave engineering and physical aspects of wireless communication In this book, the author addresses a wide range of radio-frequency and microwave topics with emphasis on physical aspects including EM and voltage waves, transmission lines, passive circuits, antennas, radio wave propagation. Up-to-date RF design tools like RF circuit simulation, EM simulation and computerized smith charts, are used in various examples to demonstrate how these methods can be applied effectively in RF engineering

  20. SPS RF System Amplifier plant

    CERN Multimedia

    1977-01-01

    The picture shows a 2 MW, 200 MHz amplifier plant with feeder lines. The main RF-system of the SPS comprises four cavities: two of 20 m length and two of 16.5 m length. They are all installed in one long straight section (LSS 3). These cavities are of the travelling-wave type operating at a centre frequency of 200.2 MHz. They are wideband, filling time about 700 ns and untuned. The power amplifiers, using tetrodes are installed in a surface building 200 m from the cavities. Initially only two cavities were installed, a third cavity was installed in 1978 and a forth one in 1979. The number of power amplifiers was also increased: to the first 2 MW plant a second 2 MW plant was added and by end 1979 there were 8 500 kW units combined in pairs to feed each of the 4 cavities with up to about 1 MW RF power, resulting in a total accelerating voltage of about 8 MV. See also 7412016X, 7412017X, 7411048X.

  1. Overview of the RF Systems for LCLS

    CERN Document Server

    McIntosh, Peter; Boyce, Richard; Emma, Paul; Hill, Alan; Rago, Carl

    2005-01-01

    The Linac Coherent Light Source (LCLS) at SLAC, when it becomes operational in 2009, will provide its user community with an X-ray source many orders of magnitude brighter than anything available in the world at that time. The electron beam acceleration will be provided by existing and new RF systems capable of maintaining the amplitude and phase stability of each bunch to extremely tight tolerances. RF feedback control of the various RF systems will be fundamental in ensuring the beam arrives at the LCLS undulator at precisely the required energy and phase. This paper details the requirements for RF stability for the various LCLS RF systems and also highlights proposals for how these injector and Linac RF systems can meet these constraints.

  2. Moscow Meson Factory DTL RF System Upgrade

    CERN Document Server

    Esin, S K; Kvasha, A I; Serov, V L

    2004-01-01

    The last paper devoted to description of the first part (DTL) RF system of Moscow Meson Factory upgrade was published in the Proceedings of PAC95 Conference in Dallas. Since then some new works directed at improvement of reliability and efficiency of the RF system were carried out. Among them there are a new powerful pulse triode “Katran” installed in the output RF power amplifiers (PA) of three channels, modifications of the anode modulator control circuit and crow-bar system, a new additional RF channel for RF supply of RFQ and some alterations in placing of the anode modulator equipment decreasing a level of interference’s at crow-bar circuits. Some new checked at MMF RF channels ideas concerning of PA tuning are of interest for people working in this sphere of activity.

  3. Scalable Multifunction RF Systems: Combined vs. Separate Transmit and Receive Arrays

    NARCIS (Netherlands)

    Huizing, A.G.

    2008-01-01

    A scalable multifunction RF (SMRF) system allows the RF functionality (radar, electronic warfare and communications) to be easily extended and the RF performance to be scaled to the requirements of different missions and platforms. This paper presents the results of a trade-off study with respect to

  4. Wideband vs. Multiband Trade-offs for a Scalable Multifunction RF system

    NARCIS (Netherlands)

    Huizing, A.G.

    2005-01-01

    This paper presents a concept for a scalable multifunction RF (SMRF) system that allows the RF functionality (radar, electronic warfare and communications) to be easily extended and the RF performance to be scaled to the requirements of different missions and platforms. A trade-off analysis is perfo

  5. Software-Defined Ultra-wideband Radio Communications: A New RF Technology for Emergency Response Applications

    Energy Technology Data Exchange (ETDEWEB)

    Nekoogar, F; Dowla, F

    2009-10-19

    Reliable wireless communication links for local-area (short-range) and regional (long-range) reach capabilities are crucial for emergency response to disasters. Lack of a dependable communication system can result in disruptions in the situational awareness between the local responders in the field and the emergency command and control centers. To date, all wireless communications systems such as cell phones and walkie-talkies use narrowband radio frequency (RF) signaling for data communication. However, the hostile radio propagation environment caused by collapsed structures and rubble in various disaster sites results in significant degradation and attenuation of narrowband RF signals, which ends up in frequent communication breakdowns. To address the challenges of reliable radio communication in disaster fields, we propose an approach to use ultra-wideband (UWB) or wideband RF waveforms for implementation on Software Defined Radio (SDR) platforms. Ultra-wideband communications has been proven by many research groups to be effective in addressing many of the limitations faced by conventional narrowband radio technologies. In addition, LLNL's radio and wireless team have shown significant success in field deployment of various UWB communications system for harsh environments based on LLNL's patented UWB modulation and equalization techniques. Furthermore, using software defined radio platform for UWB communications offers a great deal of flexibility in operational parameters and helps the radio system to dynamically adapt itself to its environment for optimal performance.

  6. Operation experience with the LHC RF system

    CERN Document Server

    Arnaudon, L; Brunner, O; Butterworth, A

    2010-01-01

    The LHC ACS RF system is composed of 16 superconducting cavities, eight per ring, housed in a total of four cryomodules each containing four cavities. Each cavity is powered by a 300 kW klystron. The ACS RF power control system is based on industrial Programmable Logic Controllers (PLCs), with additional fast RF interlock protection systems. The Low Level RF (LLRF) is implemented in VME crates. Operational performance and reliability are described. A full set of user interfaces, both for experts and operators has been developed, with user feedback and maintenance issues as key points. Operational experience with the full RF chain, including the low level system, the beam control, the synchronization system and optical fibers distribution is presented. Last but not least overall performance and reliability based on experience with first beam are reviewed and perspectives for future improvement outlined.

  7. KSTAR RF heating system development

    Energy Technology Data Exchange (ETDEWEB)

    Kwak, J. G.; Kim, S. K.; Hwang, C. K. (and others)

    2007-10-15

    Design, high-voltage test, and installation of 6 MW ICRF heating system for KSTAR is completed. The antenna demonstrated satisfactory standoff at high voltages up to 41 kV for 300 sec. The result indicates good power handling capabilities of the antenna as high as 10 MW/m2. This power density is equivalent to RF power coupling of 6 MW into a 4 {omega}/m target plasma, and is typical of advanced tokamak heating scenarios. In addition, vacuum feed through, DC break, and liquid stub developed for 300 sec operation are installed, as well as a 2 MW, 30-60MHz transmitter. The transmitter successfully produced output powers of 600 kW continuously, 1.5{approx}1.8 MW for 300 sec, and 2 MW for 100 msec or shorter pulses. A realtime control system based on DSP and EPICS is developed, installed, and tested on the ICRF system. Initial results from feasibility study indicate that the present antenna and the transmission lines could allow load-resilient operation on KSTAR. Until the KSTAR tokamak start to produce plasmas in 2008, however, hands-on operational experiences are obtained from participating in ICRF heating experiments at ASDEX and DIII-D tokamaks arranged through international cooperation.

  8. FERMILAB CRYOMODULE TEST STAND RF INTERLOCK SYSTEM

    Energy Technology Data Exchange (ETDEWEB)

    Petersen, Troy [Fermilab; Diamond, J. S. [Fermilab; McDowell, D. [Fermilab; Nicklaus, D. [Fermilab; Prieto, P. S. [Fermilab; Semenov, A. [Fermilab

    2016-10-12

    An interlock system has been designed for the Fermilab Cryo-module Test Stand (CMTS), a test bed for the cryo- modules to be used in the upcoming Linac Coherent Light Source 2 (LCLS-II) project at SLAC. The interlock system features 8 independent subsystems, one per superconducting RF cavity and solid state amplifier (SSA) pair. Each system monitors several devices to detect fault conditions such as arcing in the waveguides or quenching of the SRF system. Additionally each system can detect fault conditions by monitoring the RF power seen at the cavity coupler through a directional coupler. In the event of a fault condition, each system is capable of removing RF signal to the amplifier (via a fast RF switch) as well as turning off the SSA. Additionally, each input signal is available for re- mote viewing and recording via a Fermilab designed digitizer board and MVME 5500 processor.

  9. Control of the LHC 400 MHz RF System (ACS)

    CERN Document Server

    Arnaudon, L; Maesen, P; Prax, M

    2004-01-01

    The LHC ACS RF system is composed of 16 superconducting cavities, eight per ring. Each ring has two cryomodules, each containing four cavities. Each cavity is powered by a 300 kW klystron. The klystrons are grouped in fours, the klystrons in each group sharing a common 58 kV power converter and HV equipment bunker. The ACS RF control system is based on modern industrial programmable controllers (PLCs). A new fast interlock and alarm system with inbuilt diagnostics has been developed. Extensive use of the FIPIO Fieldbus drastically decreases the cabling complexity and brings improved signal quality, increased reliability and easier maintenance. Features of the implementation, such as system layout, communication and the high-level software interface are described. Operational facilities such as the automatic switch on procedure are described, as well as the necessary specialist tools and interfaces. A complete RF chain, including high voltage, cryomodule and klystron is presently being assembled in order to ch...

  10. Design of RF Power System for CPHS

    Science.gov (United States)

    Cheng, Cheng; Du, Taibin; Guan, Xialing

    The Compact Pulsed Hadron Source (CPHS) system has been proposed and designed by the Department of Engineering Physics of Tsinghua University in Beijing, China. It consists of an accelerator front-end-a highintensity ion source, a 3 MeV radiofrequency quadrupole linac (RFQ), and a 13 MeV drift-tube linac (DTL), a neutron target station, and some experimental stations. In design of our RF power supply, both RFQ and DTL share a single klystron which is capable of 2.5 MW peak RF power and a 3.33% duty factor. The 325 MHz klystron contains a modulating anode and has a 100 kW average output power. Portions of the RF power system, such as pulsed high voltage power supply, modulator, crowbar protection and RF power transmission are all presented in details in this paper.

  11. RF and Optical Communications: A Comparison of High Data Rate Returns From Deep Space in the 2020 Timeframe

    Science.gov (United States)

    Williams, W. Dan; Collins, Michael; Boroson, Don M.; Lesh, James; Biswas, Abihijit; Orr, Richard; Schuchman, Leonard; Sands, O. Scott

    2007-01-01

    As NASA proceeds with plans for increased science data return and higher data transfer capacity for science missions, both RF and optical communications are viable candidates for significantly higher-rate communications from deep space to Earth. With the inherent advantages, smaller apertures and larger bandwidths, of optical communications, it is reasonable to expect that at some point in time and combination of increasing distance and data rate, the rapidly emerging optical capabilities would become more advantageous than the more mature and evolving RF techniques. This paper presents a comparison of the burden to a spacecraft by both RF and optical communications systems for data rates of 10, 100, and 1000 Mbps and large distances. Advanced technology for RF and optical communication systems have been considered for projecting capabilities in the 2020 timeframe. For the comparisons drawn, the optical and RF ground terminals were selected to be similar in cost. The RF system selected is composed of forty-five 12-meter antennas, whereas the selected optical system is equivalent to a 10-meter optical telescope. Potential differences in availability are disregarded since the focus of this study is on spacecraft mass and power burden for high-rate mission data, under the assumption that essential communications will be provided by low-rate, high availability RF. For both the RF and optical systems, the required EIRP, for a given data rate and a given distance, was achieved by a design that realized the lowest possible communications subsystem mass (power + aperture) consistent with achieving the lowest technology risk. A key conclusion of this paper is that optical communications has great potential for high data rates and distances of 2.67 AU and beyond, but requires R&D and flight demonstrations to prove out technologies.

  12. The CEBAF RF Separator System Upgrade

    CERN Document Server

    Hovater, C; Guerra, A; Nelson, R; Terrel, R A; Wissmann, M

    2004-01-01

    The CEBAF accelerator uses RF deflecting cavities operating at the third sub-harmonic (499 MHz) of the accelerating frequency (1497 MHz) to “kick” the electron beam to the experimental halls. The cavities operate in a TEM dipole mode incorporating mode enhancing rods to increase the cavity’s transverse shunt impedance. As the accelerators energy has increased from 4 GeV to 6 GeV the RF system, specifically the 1 kW solid state amplifiers, have become problematic, operating in saturation because of the increased beam energy demands. Two years ago we began a study to look into replacement for the RF amplifiers and decided to use a commercial broadcast Inductive Output Tube (IOT) capable of 30 kW. The new RF system uses one IOT amplifier on multiple cavities as opposed to one amplifier per cavity originally. In addition the new RF system supports the proposed 12 GeV energy upgrade to CEBAF. Currently we are halfway through the upgrade with two IOTs in operation and two more to be in...

  13. Outage Performance of Hybrid FSO/RF System with Low-Complexity Power Adaptation

    KAUST Repository

    Rakia, Tamer

    2016-02-26

    Hybrid free-space optical (FSO) / radio-frequency (RF) systems have emerged as a promising solution for high data- rate wireless communication systems. We consider truncated channel inversion based power adaptation strategy for coherent and non- coherent hybrid FSO/RF systems, employing an adaptive combining scheme. Specifically, we activate the RF link along with the FSO link when FSO link quality is unacceptable, and adaptively set RF transmission power to ensure constant combined signal-to-noise ratio at receiver terminal. Analytical expressions for the outage probability of the hybrid system with and without power adaptation are derived. Numerical examples show that, the hybrid FSO/RF systems with power adaptation achieve considerable outage performance improvement over conventional hybrid FSO/RF systems without power adaptation. © 2015 IEEE.

  14. Delay-Modulated RF Tag System Concept Using Ultrawideband Noise Radar Waveforms

    OpenAIRE

    2011-01-01

    Radio frequency (RF) tags have been widely used in inventory tracking, environmental monitoring, battlefield situational awareness, and combat identification due to their low cost, small size, and wireless functionality. This paper explores the application of active RF tags in outdoor environments responding to random noise radar interrogations with predetermined messages. A conceptual system design for communication between radar and RF tags using ultrawideband (UWB) noise waveforms is propo...

  15. Connect Global Positioning System RF Module

    Science.gov (United States)

    Franklin, Garth W.; Young, Lawrence E.; Ciminera, Michael A.; Tien, Jeffrey Y.; Gorelik, Jacob; Okihiro, Brian Bachman; Koelewyn, Cynthia L.

    2012-01-01

    The CoNNeCT Global Positioning System RF Module (GPSM) slice is part of the JPL CoNNeCT Software Defined Radio (SDR). CoNNeCT is the Communications, Navigation, and Net working reconfigurable Testbed project that is part of NASA's Space Communication and Nav igation (SCaN) Program. The CoNNeCT project is an experimental dem onstration that will lead to the advancement of SDRs and provide a path for new space communication and navigation systems for future NASA exploration missions. The JPL CoNNeCT SDR will be flying on the International Space Station (ISS) in 2012 in support of the SCaN CoNNeCT program. The GPSM is a radio-frequency sampler module (see Figure 1) that directly sub-harmonically samples the filtered GPS L-band signals at L1 (1575.42 MHz), L2 (1227.6 MHz), and L5 (1176.45 MHz). The JPL SDR receives GPS signals through a Dorne & Margolin antenna mounted onto a choke ring. The GPS signal is filtered against interference, amplified, split, and fed into three channels: L1, L2, and L5. In each of the L-band channels, there is a chain of bandpass filters and amplifiers, and the signal is fed through each of these channels to where the GPSM performs a one-bit analog-to-digital conversion (see Figure 2). The GPSM uses a sub-harmonic, single-bit L1, L2, and L5 sampler that samples at a clock rate of 38.656 MHz. The new capability is the down-conversion and sampling of the L5 signal when previous hardware did not provide this capability. The first GPS IIF Satellite was launched in 2010, providing the new L5 signal. With the JPL SDR flying on the ISS, it will be possible to demonstrate navigation solutions with 10-meter 3-D accuracy at 10-second intervals using a field-program mable gate array (FPGA)-based feedback loop running at 50 Hz. The GPS data bits will be decoded and used in the SDR. The GPSM will also allow other waveforms that are installed in the SDR to demonstrate various GNSS tracking techniques.

  16. Modeling and simulation for RF system design

    CERN Document Server

    Frevert, Ronny; Jancke, Roland; Knöchel, Uwe; Schwarz, Peter; Kakerow, Ralf; Darianian, Mohsen

    2005-01-01

    Focusing on RF specific modeling and simulation methods, and system and circuit level descriptions, this work contains application-oriented training material. Accompanied by a CD- ROM, it combines the presentation of a mixed-signal design flow, an introduction into VHDL-AMS and Verilog-A, and the application of commercially available simulators.

  17. Hybrid RF/Optical Communications via 34-meter DSN Antennas

    Science.gov (United States)

    Vilnrotter, V.

    2010-02-01

    There is considerable interest in determining whether suitably modified versions of existing 34-m antennas at NASA's Goldstone Communications Complex, originally designed for X-band (nominally 8 GHz) and Ka-band (32 GHz) operation, could also be used to receive near-infrared optical signals. The robust backup structure of these antennas, together with extremely large collecting apertures and millidegree pointing capabilities, suggest that dual RF/optical communications may indeed be possible, at optical data rates approaching 1 gigabit per second (GBPS) from typical Mars distances. Several design concepts have emerged as possible candidates, requiring modifications ranging from polishing and coating of the existing aluminum panels of the main reflector, to significant redesign involving replacement of the panels with optical reflectors. Optical receiver parameters such as collecting area, field of view (FOV), and immunity to reflected sunlight differ markedly for each design concept, hence will likely lead to different levels of performance in terms of data throughput at a given error probability, and in terms of the ability to point close to the Sun. The communications performance of two candidate design concepts operating under realistic daytime conditions is evaluated, with particular emphasis on spatial and temporal acquisition algorithms and receiver optimization to achieve the best possible communication performance at high data rates.

  18. Development of the RF system for the KOMAC MEBT

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Seong-Gu; Seol, Kyung-Tae; Kwon, Hyeok-Jung; Kim, Han-Sung; Song, Young-Gi; Cho, Yong-Sub [KOMAC, Gyeongju (Korea, Republic of)

    2015-05-15

    In the 100 MeV proton linear accelerator (Linac) for KOMAC, the RF source will power two-accelerator cavities (an RFQ, a DTL1) operated at a frequency of 350 MHz. The low level RF (LLRF) system for 100 MeV proton linear accelerator provides field control including an RFQ and a DTL at 350 MHz. In our system, an accelerating electric field stability of ±1% in amplitude and ±1° in phase is required for the RF system. Eleven radio-frequency (RF) systems are required for the 100 MeV accelerator, which are one RF system for the radio-frequency quadrupole (RFQ) cavity, one RF system for the 20 MeV drift tube linear accelerator (DTL) tanks, two RF systems for the medium-energy beam transmission (MEBT) tanks, and seven RF systems for the 100 MeV DTL tanks. Now a total of 9 RF systems are being operated. To improve the beam quality, the additional RF system for MEBT (Medium Energy Beam Transport) is needed. An addition of a MEBT RF system will reduce loss of beam quantity caused by gab between 20 MeV DTL tank and 100 MeV DTL tank. RF system for MEBT is being installed. The condition of the test is 350 MHz, 9% pulse duty (1.5 ms, 60 Hz), 4 kW(peak power). Perfecting an RF system of MEBT will reduce loss of beam quantity.

  19. New Driver For The Powerful Output Rf Amplifier Of Mmf Dtl Rf System

    CERN Document Server

    Kvasha, A I; Vassilyev, A G

    2004-01-01

    More than 30 years ago a few powerful vacuum tubes were specially designed and produced in the former design office Swetlana for the Moscow meson factory DTL RF system. Among them was tetrode GI-51A with output pulse RF power up to 300 kW at frequency 198.2 MHz, which was used as driver for RF power amplifier with output RF pulse power (2-3) MW. In connection with well-known events in our country manufacture of these tubes, including GI-51A was finished about 10 years ago. In "SED-SPb" (successor of the design office Swetlana) triode GI-57A was offered instead of GI-51A. In this paper results of calculations and design of RF amplifier with new triode are presented. Preliminary results of RF amplifier tests, also presented in the paper, showed that triode GI-57A will be able successfully used in the DTL RF system channels.

  20. 基于nRF24L01的无线数字传输系统%Design of wireless communication system based on nRF24L01

    Institute of Scientific and Technical Information of China (English)

    刘靖; 陈在平; 李其林

    2007-01-01

    介绍了一种以无线数字传输芯片nRF24L01和AVR系列MCU组成的无线数字传输系统,详细阐述了硬件和软件的设计要点.给出了nRF24L01结合ATmega64具体的硬件电路和软件设计,最后讨论了该系统结合USB技术在无线数据采集上的应用.

  1. The Design of Wireless Bidirectional Communication System Based on nRF24L01%基于nRF24L01无线双向通信系统设计

    Institute of Scientific and Technical Information of China (English)

    丁媛媛

    2012-01-01

    文章以nRF24 L01无线收发模块和AT89S51单片机为核心,设计了以nRF24L01芯片为基础进行无线双向传输的系统,主要介绍发射器和接收器软硬件结构及微控制器和无线收发芯片的应用.

  2. ILC RF System R and D

    Energy Technology Data Exchange (ETDEWEB)

    Adolphsen, Chris; /SLAC

    2012-07-03

    The Linac Group at SLAC is actively pursuing a broad range of R&D to improve the reliability and reduce the cost of the L-band (1.3 GHz) rf system proposed for the ILC linacs. Current activities include the long-term evaluation of a 120 kV Marx Modulator driving a 10 MW Multi-Beam Klystron, design of a second-generation Marx Modulator, testing of a sheet-beam gun and beam transport system for a klystron, construction of an rf distribution system with remotely-adjustable power tapoffs, and development of a system to combine the power from many klystrons in low-loss circular waveguide where it would be tapped-off periodically to power groups of cavities. This paper surveys progress during the past few years.

  3. R.F. Pollution Reduction in Cellular Communication

    CERN Document Server

    Katiyar, Sumit; Agrawal, N K

    2012-01-01

    R. F. pollution has been recognized as health hazard in India in the prevailing circumstances. There is lot of hue and cry against cellular towers installed in residential area. Recently high court in India has issued an order not to install towers in residential areas. For meeting the exponential demand of cellular communication in India this will be a set back for future growth. An appropriate solution has to be developed for meeting demand as well as RF pollution concern of the society. This paper deals with the installation of low power base stations in residential areas instead of high power macro cell base stations. Macro stations are proposed to be used for fast traffic, low power micro cell for a slow traffic / pedestrian and pico cell / femto cell for indoor use. These cells will be in hierarchical structure along with adaptive frequency allocation techniques and A-SDMA approach.

  4. NSLS-II RF Cryogenic System

    Energy Technology Data Exchange (ETDEWEB)

    Rose, J.; Dilgen, T.; Gash, B.; Gosman, J.; Mortazavi, P.; Papu, J.; Ravindranath, V.; Sikora, R.; Sitnikov, A.; Wilhelm, H.; Jia, Y.; Monroe, C.

    2015-05-03

    The National Synchrotron Light Source II is a 3 GeV X-ray user facility commissioned in 2014. A new helium refrigerator system has been installed and commissioned to support the superconducting RF cavities in the storage ring. Special care was taken to provide very stable helium and LN2 pressures and flow rates to minimize microphonics and thermal effects at the cavities. Details of the system design along with commissioning and early operations data will be presented.

  5. Modeling of the RF system for the normal conducting linac

    Institute of Scientific and Technical Information of China (English)

    GENG Zhe-Qiao; HOU Mi; PEI Guo-Xi

    2008-01-01

    To study the new RF control methods, a mathematic model of the RF system for the normal conducting linac is built and implemented with the software of Matlab. The model contains some typical units of the RF system, such as the klystron, the SLED and the traveling wave accelerating tube. Finally, the model is used to study the working point of the SLED and the adaptive feed forward algorithm for the RF control system. Simulation shows that the model works well as expected.

  6. 基于nRF24L01的无线通信系统设计%Design of System of Wireless Communications Based on nRF24L01

    Institute of Scientific and Technical Information of China (English)

    王峰; 邢磊; 史星晟; 武杰; 周锐

    2011-01-01

    介绍了一种以nRF24L01无线收发芯片,以ATmega16单片机为控制核心的半双工无线通信系统,并对系统进行了传输速率和传榆距离的测试,详细阐述了硬件和软件的设计要点.

  7. SPS RF System an Accelerating Cavity

    CERN Multimedia

    CERN PhotoLab

    1975-01-01

    The picture shows one of the two initially installed cavities. The main RF-system of the SPS comprises four cavities: two of 20 m length and two of 16.5 m length. They are all installed in one long straight section (LSS 3). These cavities are of the travelling-wave type operating at a centre frequency of 200.2 MHz. They are wideband, filling time about 700 ns and untuned. The power amplifiers, using tetrodes are installed in a surface building 200 m from the cavities. Initially only two cavities were installed, a third cavity was installed in 1978 and a forth one in 1979. The number of power amplifiers was also gradually increased: by end 1980 there were 8 500 kW units combined in pairs to feed each of the 4 cavities with up to about 1 MW RF power, resulting in a total accelerating voltage of about 8 MV. See also 7412017X, 7411048X.

  8. SPS RF system:Tetrodes and waveguides

    CERN Multimedia

    1974-01-01

    This picture shows one of the initially installed amplifier units of the SPS RF system. The main RF-system of the SPS comprises four cavities: two of 20 m length and two of 16.5 m length. They are all installed in one long straight section (LSS 3). These cavities are of the travelling-wave type operating at a centre frequency of 200.2 MHz. They are wideband, filling time about 700 ns and untuned. The power amplifiers, using tetrodes are installed in a surface building 200 m from the cavities. Initially only two cavities were installed, a third cavity was installed in 1978 and a forth one in 1979. The number of power amplifiers was also gradually increased: in 1980 there were 8 500 kW units combined in pairs to feed each of the 4 cavities with up to about 1 MW RF power, resulting in a total accelerating voltage of about 8 MV. See also 7412017X, 7411048X.

  9. PEP-II RF feedback system simulation

    Energy Technology Data Exchange (ETDEWEB)

    Tighe, R. [Stanford Linear Accelerator Center, Menlo Park, CA (United States)

    1996-08-01

    A model containing the fundamental impedance of the PEP-II cavity along with the longitudinal beam dynamics and RF feedback system components is in use. It is prepared in a format allowing time-domain as well as frequency-domain analysis and full graphics capability. Matlab and Simulink are control system design and analysis programs (widely available) with many built-in tools. The model allows the use of compiled C-code modules for compute intensive portions. We desire to represent as nearly as possible the components of the feedback system including all delays, sample rates and applicable nonlinearities. (author)

  10. SPS RF System:Tetrodes and Waveguides

    CERN Multimedia

    1977-01-01

    The picture shows part of a RF power generating plant. The main RF-system of the SPS comprises four cavities: two of 20 m length and two of 16.5 m length. They are all installed in one long straight section (LSS 3). These cavities are of the travelling-wave type operating at a centre frequency of 200.2 MHz. They are wideband, filling time about 700 ns and untuned. The power amplifiers, using tetrodes are installed in a surface building 200 m from the cavities. Initially only two cavities were installed, a third cavity was installed in 1978 and a forth one in 1979. The number of power amplifiers was also gradually increased: by end 1980 there were 8 500 kW units combined in pairs to feed each of the 4 cavities with up to about 1 MW RF power, resulting in a total accelerating voltage of about 8 MV. See also 7412016X, 7412017X, 7411048X.

  11. Outage Analysis of Asymmetric RF-FSO Systems

    KAUST Repository

    Ansari, Imran Shafique

    2017-03-20

    In this work, the outage performance analysis of a dual-hop transmission system composed of asymmetric radio frequency (RF) channels cascaded with free-space optical (FSO) links is presented. The RF links are modeled by the Rayleigh fading distribution and the FSO links are modeled by Malaga (M) turbulence distribution. The FSO links account for pointing errors and both types of detection techniques (i.e. heterodyne detection as well as intensity modulation/direct detection (IM/DD)). Transmit diversity is applied at the source, selection combining is applied at the destination, and the relay is equipped with single RF receive antenna and single aperture for relaying the information over FSO links. With this model, a new exact closed-form expression is derived for the outage probability of the end-to- end signal-to-noise ratio of such communication systems in terms of the Meijer\\'s G function under fixed amplify-and-forward relay scheme. All new analytical results are verified via computer-based Monte-Carlo simulations and are illustrated by some selected numerical results.

  12. 2.4 GHz Wireless Communication System Design Based on nRF24L01%基于nRF24L01的2.4GHz无线通信系统设计

    Institute of Scientific and Technical Information of China (English)

    王涛

    2011-01-01

    提出一种基于NORDIC公司生产的2.4 GHz无线收发芯片nRF24L01的短距离无线数据传输系统设计方法.介绍了系统的实现方案和硬件选型,该系统以ATmega8L为控制核心,PTR6000为无线传输模块;详细描述了硬件电路和软件程序设计方法,其中软件设计包括单片机主程序设计和PTR6000通信程序设计等;在硬件和软件设计的基础上,通过实验仿真验证了系统的正确性和可靠性,为系统实际应用提供了依据,最终达到了设计的要求.

  13. Accelerating Rf System Of Microtron-recuperator For Fel

    CERN Document Server

    Arbuzov, V S; Gorniker, E I; Kendjebulatov, E K; Kolobanov, E I; Kondakov, A A; Krutikhin, S A; Kuptsov, I V; Kurkin, G Ya; Medvedev, L E; Motygin, S V; Osipov, V N; Petrov, V M; Pilan, Andrey M; Popov, A M; Sedlyarov, I K; Tribendis, A G

    2004-01-01

    FEL (Free Electron Laser) for the Siberian Centre of Photochemical Research is constructed in Novosibirsk. Parameters and last results received on a RF system of the race-track microtron-recuperator for FEL are given in the report. The frequency of the RF system is 180.4 MHz. The RF system operates in continuous mode. The 16 cavities are used in accelerating system of the microtron-recuperator. The RF system is consists of two channels. Each of two 600kW generators drives 8 cavities. Each channel was tested at 7500 kV on the gaps of 8 cavities. The RF power was 630 kW per channel. Now, the accelerating RF system operates at 13600 kV on 16 cavities. Total power of generators is 1100kW.

  14. System for Isolation Testing of RF Transmitters and Receivers

    Science.gov (United States)

    2012-08-03

    one such software defined radio is the open source GNU radio platform utilizing the Universal Software Radio Peripheral. [0019] The advantages of...to a system that can perform isolation testing of a radio frequency (RF) transmitter or an RF receiver. (2) Description of the Prior Art [0004...Currently, the testing and diagnosing of a faulty radio frequency (RF) transmission and receiving systems requires that the system be taken out of the

  15. Whip antenna design for portable rf systems

    Science.gov (United States)

    Ponnapalli, Saila; Canora, Frank J.

    1995-12-01

    Whip type antennas are probably the most commonly used antennas in portable rf systems, such as cordless and cellular phones, rf enabled laptop computers, personal digital assistants (PDAs), and handheld computers. Whip antennas are almost always mounted on the chassis which contains the radio and other electronics. The chassis is usually a molded plastic which is coated with a conducting paint for EMI purposes. The chassis which appears as a lossy conductor to the antenna, has several effects -- detuning, altering the gain of the antenna, and shadowing its radiation pattern. Extensive modeling and measurements must be performed in order to fully characterize the affects of the chassis on the whip antenna, and to optimize antenna type, orientation and position. In many instances, modeling plays a more important role in prediction of the performance of whip antennas, since measurements become difficult due to the presence of common mode current on feed cables. In this paper models and measurements are used to discuss the optimum choice of whip antennas and the impact of the chassis on radiation characteristics. A modeling tool which has been previously described and has been successfully used to predict radiated field patterns is used for simulations, and measured and modeled results are shown.

  16. SPS RF System:Tetrodes and Waveguides

    CERN Multimedia

    1974-01-01

    The main RF-system of the SPS comprises four cavities: two of 20 m length and two of 16.5 m length. They are all installed in one long straight section (LSS 3). These cavities are of the travelling-wave type operating at a centre frequency of 200.2 MHz. They are wideband, filling time about 700 ns and untuned. The power amplifiers, using tetrodes are installed in a surface building 200 m from the cavities. Initially only two cavities were installed, a third cavity was installed in 1978 and a forth one in 1979. The number of power amplifiers was also increased: to the first 2 MW plant a second 2 MW plant was added and by end 1979 there were 8 500 kW units combined in pairs to feed each of the 4 cavities with up to about 1 MW RF power, resulting in a total accelerating voltage of about 8 MV. See also 7412016X, 7412017X, 7411048X.

  17. Control system analysis for the perturbed linear accelerator rf system

    CERN Document Server

    Sung Il Kwon

    2002-01-01

    This paper addresses the modeling problem of the linear accelerator RF system in SNS. Klystrons are modeled as linear parameter varying systems. The effect of the high voltage power supply ripple on the klystron output voltage and the output phase is modeled as an additive disturbance. The cavity is modeled as a linear system and the beam current is modeled as the exogenous disturbance. The output uncertainty of the low level RF system which results from the uncertainties in the RF components and cabling is modeled as multiplicative uncertainty. Also, the feedback loop uncertainty and digital signal processing signal conditioning subsystem uncertainties are lumped together and are modeled as multiplicative uncertainty. Finally, the time delays in the loop are modeled as a lumped time delay. For the perturbed open loop system, the closed loop system performance, and stability are analyzed with the PI feedback controller.

  18. LHC RF System Time-Domain Simulation

    Energy Technology Data Exchange (ETDEWEB)

    Mastorides, T.; Rivetta, C.; /SLAC

    2010-09-14

    Non-linear time-domain simulations have been developed for the Positron-Electron Project (PEP-II) and the Large Hadron Collider (LHC). These simulations capture the dynamic behavior of the RF station-beam interaction and are structured to reproduce the technical characteristics of the system (noise contributions, non-linear elements, and more). As such, they provide useful results and insight for the development and design of future LLRF feedback systems. They are also a valuable tool for the study of diverse longitudinal beam dynamics effects such as coupled-bunch impedance driven instabilities and single bunch longitudinal emittance growth. Results from these studies and related measurements from PEP-II and LHC have been presented in multiple places. This report presents an example of the time-domain simulation implementation for the LHC.

  19. The system of RF beam control for electron gun

    Science.gov (United States)

    Barnyakov, A. M.; Chernousov, Yu. D.; Ivannikov, V. I.; Levichev, A. E.; Shebolaev, I. V.

    2015-06-01

    The system of RF control of three-electrode electron gun current is described. It consists of a source of microwave signal, coaxial line, coaxial RF switch and RF antenna lead. The system allows one to get the electron beam in the form of bunches with the frequency of the accelerating section to achieve the capture of particles in the acceleration mode close to 100%. The results of calculation and analysis of the elements of the system are presented. Characteristics of the devices are obtained experimentally. The results of using RF control in three-electrode electron gun at electron linear accelerator are described.

  20. Superconducting Quantum Arrays for Broadband RF Systems

    Science.gov (United States)

    Kornev, V.; Sharafiev, A.; Soloviev, I.; Kolotinskiy, N.; Mukhanov, O.

    2014-05-01

    Superconducting Quantum Arrays (SQAs), homogenous arrays of Superconducting Quantum Cells, are developed for implementation of broadband radio frequency (RF) systems capable of providing highly linear magnetic signal to voltage transfer with high dynamic range, including active electrically small antennas (ESAs). Among the proposed quantum cells which are bi-SQUID and Differential Quantum Cell (DQC), the latter delivered better performance for SQAs. A prototype of the transformer-less active ESA based on a 2D SQA with nonsuperconducting electric connection of the DQCs was fabricated using HYPRES niobium process with critical current density 4.5 kA/cm2. The measured voltage response is characterized by a peak-to-peak swing of ~100 mV and steepness of ~6500 μV/μT.

  1. Antenna and RF Subsystem Integration in Cellular Communications

    DEFF Research Database (Denmark)

    Herrero, Pablo; Bahramzy, Pevand; Svendsen, Simon

    2014-01-01

    wireless standards and demanding power and size requirements. The first technique is based on integrating the antenna as part of the RF filtering chain to relax the requirements of current duplex filters up to 30dB off-band. We also outline a discussion on the different approaches for adaptive antenna......We discuss in this article a number of techniques that can be used to improve the RF performance on a mobile device. All those techniques rely on tight antenna and modem subsystem codesign. In a short introduction, the article outlines the need of these techniques, based on the advent of new...

  2. Performance analysis of mixed RF/FSO systems with STBC users

    Science.gov (United States)

    Feng, Jianfeng; Zhao, Xiaohui

    2016-12-01

    In consideration of either fixed or variable gain relay scheme, end-to-end performance analysis of a dual-hop relay system over the asymmetric links composed of both radio-frequency (RF) and free-space optical (FSO) links with space time block coding (STBC) and two transmit antennas for the RF users is provided. In the analysis the RF links are modeled as the Rayleigh fading channel and the FSO link as the Gamma-Gamma fading channel with pointing errors. Closed-form expressions for the end-to-end outage probability (OP) and average symbol error probability (ASEP) in terms of the Meijer's G functions are obtained. Based on the asymptotic expansion of the Meijer's G function at high-SNR region, the asymptotic OP performance of the mixed RF/FSO systems with the fixed gain relay and misalignment FSO channels is discussed. Numerical simulations demonstrate that the system performance deteriorates when channel conditions become severe, and the RF users using STBC can achieve better communication quality than that of the regular RF users. In addition, the system with the fixed gain relay is better than that with the variable gain relay under the same average SNR in both the RF links and the FSO links.

  3. A COTS RF/Optical Software Defined Radio for the Integrated Radio and Optical Communications Test Bed

    Science.gov (United States)

    Nappier, Jennifer M.; Zeleznikar, Daniel J.; Wroblewski, Adam C.; Tokars, Roger P.; Schoenholz, Bryan L.; Lantz, Nicholas C.

    2017-01-01

    The Integrated Radio and Optical Communications (iROC) project at the National Aeronautics and Space Administration (NASA) is investigating the merits of a hybrid radio frequency (RF) and optical communication system for deep space missions. In an effort to demonstrate the feasibility and advantages of a hybrid RF/Optical software defined radio (SDR), a laboratory prototype was assembled from primarily commercial-off-the-shelf (COTS) hardware components. This COTS platform has been used to demonstrate simultaneous transmission of the radio and optical communications waveforms through to the physical layer (telescope and antenna). This paper details the hardware and software used in the platform and various measures of its performance. A laboratory optical receiver platform has also been assembled in order to demonstrate hybrid free space links in combination with the transmitter.

  4. Versatile Low Level RF System For Linear Accelerators

    Science.gov (United States)

    Potter, James M.

    2011-06-01

    The Low Level RF (LLRF) system is the source of all of the rf signals required for an rf linear accelerator. These signals are amplified to drive accelerator and buncher cavities. It can even provide the synchronizing signal for the rf power for a synchrotron. The use of Direct Digital Synthesis (DDS) techniques results in a versatile system that can provide multiple coherent signals at the same or different frequencies with adjustable amplitudes and phase relations. Pulsing the DDS allows rf switching with an essentially infinite on/off ratio. The LLRF system includes a versatile phase detector that allows phase-locking the rf frequency to a cavity at any phase angle over the full 360° range. With the use of stepper motor driven slug tuners multiple cavity resonant frequencies can be phase locked to the rf source frequency. No external phase shifters are required and there is no feedback loop phase setup required. All that is needed is to turn the frequency feedback on. The use of Digital Signal Processing (DSP) allows amplitude and phase control over the entire rf pulse. This paper describes the basic principles of a LLRF system that has been used for both proton accelerators and electron accelerators, including multiple tank accelerators, sub-harmonic and fundamental bunchers, and synchrotrons.

  5. Joint Adaptive Modulation and Combining for Hybrid FSO/RF Systems

    KAUST Repository

    Rakia, Tamer

    2015-11-12

    In this paper, we present and analyze a new transmission scheme for hybrid FSO/RF communication system based on joint adaptive modulation and adaptive combining. Specifically, the data rate on the FSO link is adjusted in discrete manner according to the FSO link\\'s instantaneous received signal-to-noise-ratio (SNR). If the FSO link\\'s quality is too poor to maintain the target bit-error-rate, the system activates the RF link along with the FSO link. When the RF link is activated, simultaneous transmission of the same modulated data takes place on both links, where the received signals from both links are combined using maximal ratio combining scheme. In this case, the data rate of the system is adjusted according to the instantaneous combined SNRs. Novel analytical expression for the cumulative distribution function (CDF) of the received SNR for the proposed adaptive hybrid system is obtained. This CDF expression is used to study the spectral and outage performances of the proposed adaptive hybrid FSO/RF system. Numerical examples are presented to compare the performance of the proposed adaptive hybrid FSO/RF system with that of switch-over hybrid FSO/RF and FSO-only systems employing the same adaptive modulation schemes. © 2015 IEEE.

  6. Commissioning of the 400 MHz LHC RF System

    CERN Document Server

    Ciapala, Edmond; Baudrenghien, P; Brunner, O; Butterworth, A; Linnecar, T; Maesen, P; Molendijk, J; Montesinos, E; Valuch, D; Weierud, F

    2008-01-01

    The installation of the 400 MHz superconducting RF system in LHC is finished and commissioning is under way. The final RF system comprises four cryo-modules each with four cavities in the LHC tunnel straight section round IP4. Also underground in an adjacent cavern shielded from the main tunnel are the sixteen 300 kW klystron RF power sources with their high voltage bunkers, two Faraday cages containing RF feedback and beam control electronics, and racks containing all the slow controls. The system and the experience gained during commissioning will be described. In particular, results from conditioning the cavities and their movable main power couplers and the setting up of the low level RF feedbacks will be presented.

  7. RF Sounding: A System for Generating Sounds from Spectral Analysis

    Science.gov (United States)

    Graziosi, Fabio; Rinaldi, Claudia; Tarquini, Francesco

    In this paper we present RF Sounding, an open space installation which comprises both artistic and technological innovations. The aim of this project is to provide the user entering a specifically defined area, with awareness of radio frequency signals characterizing the cellular networks band. Indeed, radio signals are shifted, with proper elaboration, to the audible band and the result is spread all over the specific area through a certain number of loudspeakers. The system produces different reactions depending on the communication phase (e.g. initial handshake procedure, reception or initiation of a call, etc.). Moreover, the sound produced after translation of signals to the audible band, is assumed to be spatialized as a function of user movement; localization is indeed achieved through a wireless sensor network that is installed in the defined area.

  8. Design of RF system for CYCIAE-230 superconducting cyclotron

    Science.gov (United States)

    Yin, Zhiguo; Ji, Bin; Fu, Xiaoliang; Cao, Xuelong; Zhao, Zhenlu; Zhang, Tinajue

    2017-05-01

    The CYCIAE230 is a low-current, compact superconducting cyclotron designed for proton therapy. The Radio Frequency system consists of four RF cavities and applies second harmonic to accelerate beams. The driving power for the cavity system is estimated to be approximately 150 kW. The LLRF controller is a self-made device developed and tested at low power using a small-scale cavity model. In this paper, the resonator systems of an S.C. cyclotron in history are reviewed. Contrary to those RF systems, the cavities of the CYCIAE230 cyclotron connect two opposite dees. Two high-power RF windows are included in the system. Each window carries approximately 75 kW RF power from the driver to the cavities. Thus, the RF system for the CY-CIAE230 cyclotron is operated in driven push-pull mode. The two-way amplifier-coupler-cavity systems are operated with approximately the same amount of RF power but 180° out of phase compared with each other. The design, as well as the technical advantage and limitations of this operating mode, of the CYCIAE230 cyclotron RF system is analyzed.

  9. 5 MW 805 MHz SNS RF System Experience

    CERN Document Server

    Young, Karen A; Hardek, Thomas; Lynch, Michael; Rees, Daniel; Roybal, William; Tallerico, Paul J; Thomas Bradley, Joseph

    2005-01-01

    The RF system for the 805 MHz normal conducting linac of the Spallation Nuetron Source (SNS) accelerator was designed, procured and tested at Los Alamos National Laboratory(LANL) and then installed and commissioned at Oak Ridge National Laboratory (ORNL). The RF power for this room temperature coupled cavity linac (CCL) of SNS accelerator is generated by four pulsed 5 MW peak power klystrons operating with a pulse width of 1.25 mSec and a 60 Hz repetition frequency. The RF power from each klystron is divided and delivered to the CCL through two separate RF windows. The 5 MW RF system advanced the state of the art for simultaneous peak and average power. This paper summarizes the problems encountered, lessons learned and results of the high power testing at LANL of the 5 MW klystrons, 5 MW circulators, 5 MW loads, and 2.5 MW windows.*

  10. Photosensing Resolution of Wireless Communication Chip in Inhomogeneous RF-Magnetic Field

    Science.gov (United States)

    Hasebe, Takehiko; Yazawa, Yoshiaki; Tase, Takashi; Kamahori, Masao; Watanabe, Kazuki; Oonishi, Tadashi

    2006-04-01

    We have developed a wireless biosensing system for bioluminescence measurements that includes a sensor chip with a volume of 2.5 × 2.5 × 0.5 mm3 and a read/write (R/W) coil. This sensor chip monolithically integrates a photosensor for detecting bioluminescence, a control circuit, and a coil for communication. In order to operate the sensor chip in a sample solution, we employed an RF magnetic field for the transmission of data and electric power between the chip and the R/W unit. The magnitude of the field around the chip changes significantly with the positional relationship between the sensor chip and the R/W coil. Therefore, evaluating the stability of the sensor chip operation, especially the resolution of signal processing, is important. In our system, a resolution of ± 30 μV was achieved in an inhomogeneous field ranging from 160 to 379 A/m. We also quantified the adenosine triphosphate (ATP) by measuring bioluminescence to demonstrate the stability of the sensing operation. Although the RF magnetic field fluctuated in the reaction cell where the sensor chip was located, an almost linear relationship between the ATP amount and the sensor response was obtained.

  11. RF impairments in high-rate wireless systems - understanding the impact of TX/RX-asymmetry

    NARCIS (Netherlands)

    Schenk, T.C.W.; Fledderus, E.R.

    2008-01-01

    Dealing with radio frequency (RF) front-end impairments will be one of the major design challenges for next-generation wireless communication systems due to conflicting requirements, such as high data rate, low cost and low power consumption. The use of digital compensation of the imperfections appe

  12. Ultra Linear Low-loss Varactors & Circuits for Adaptive RF Systems

    NARCIS (Netherlands)

    Huang, C.

    2010-01-01

    With the evolution of wireless communication, varactors can play an important role in enabling adaptive transceivers as well as phase-diversity systems. This thesis presents various varactor diode-based circuit topologies that facilitate RF adaptivity. The proposed varactor configurations can act as

  13. Development of RF System Model for CERN Linac2 Tanks

    CERN Document Server

    Joshi, G; Vretenar, M; Kumar, G; Agarwal, V

    2010-01-01

    An RF system model has been created for the CERN Linac2 Tanks. RF systems in this linac have both single and double feed architectures. The main elements of these systems are: RF power amplifier, main resonator, feed-line and the amplitude and phase feedback loops. The model of the composite system is derived by suitably concatenating the models of these individual sub-systems. For computational efficiency the modeling has been carried out in the base band. The signals are expressed in in-phase - quadrature domain, where the response of the resonator is expressed using two linear differential equations, making it valid for large signal conditions. MATLAB/SIMULINK has been used for creating the model. The model has been found useful in predicting the system behaviour, especially during the transients. In the paper we present the details of the model, highlighting the methodology, which could be easily extended to multiple feed RF systems.

  14. Hardware and Initial Beam Commissioning of the LHC RF Systems

    CERN Document Server

    Linnecar, T; Arnaudon, L; Baudrenghien, P; Bohl, T; Brunner, O; Butterworth, A; Ciapala, Edmond; Dubouchet, F; Ferreira-Bento, J; Glenat, D; Hagmann, G; Höfle, Wolfgang; Julie, C; Killing, F; Kotzian, G; Landre, D; Louwerse, R; Maesen, P; Martinez-Yanez, P; Molendijk, J; Montesinos, E; Nicou, C; Noirjean, J; Papotti, G; Pashnin, A; Pechaud, G; Pradier, J; Rossi, V; Sanchez-Quesada, J; Schokker, M; Shaposhnikova, E; Sorokoletev, R; Stellfeld, D; Tückmantel, Joachim; Valuch, D; Wehrle, U; Weierud, F

    2008-01-01

    Hardware commissioning of the LHC RF Systems, the ACS Superconducting RF systems, ADT Transverse Dampers and APWL Wideband Longitudinal Monitors, started in late 2007 and was completed in time for the first LHC beams in 2008. The RF inter-machine synchroni-sation systems were in place and operational for the LHC synchronization tests in August 2008. The very first beams through IP4 were observed on the RF monitors and beam 2 was captured on 11th September. Measurements with beam on the damper systems were also pos-sible, preparing the way for closing the damper loop with beam. Major milestones during commissioning the ACS and ADT systems and results obtained during first capture tests are presented. Preparatory work for acceleration and multi-bunch operation is described as are the beam tests foreseen for 2009.

  15. The development of data acquisition and processing application system for RF ion source

    Science.gov (United States)

    Zhang, Xiaodan; Wang, Xiaoying; Hu, Chundong; Jiang, Caichao; Xie, Yahong; Zhao, Yuanzhe

    2017-07-01

    As the key ion source component of nuclear fusion auxiliary heating devices, the radio frequency (RF) ion source is developed and applied gradually to offer a source plasma with the advantages of ease of control and high reliability. In addition, it easily achieves long-pulse steady-state operation. During the process of the development and testing of the RF ion source, a lot of original experimental data will be generated. Therefore, it is necessary to develop a stable and reliable computer data acquisition and processing application system for realizing the functions of data acquisition, storage, access, and real-time monitoring. In this paper, the development of a data acquisition and processing application system for the RF ion source is presented. The hardware platform is based on the PXI system and the software is programmed on the LabVIEW development environment. The key technologies that are used for the implementation of this software programming mainly include the long-pulse data acquisition technology, multi-threading processing technology, transmission control communication protocol, and the Lempel-Ziv-Oberhumer data compression algorithm. Now, this design has been tested and applied on the RF ion source. The test results show that it can work reliably and steadily. With the help of this design, the stable plasma discharge data of the RF ion source are collected, stored, accessed, and monitored in real-time. It is shown that it has a very practical application significance for the RF experiments.

  16. Workshop Goals: Mini-workshop on RHIC Rf system

    Energy Technology Data Exchange (ETDEWEB)

    Hahn, H. [Brookhaven National Lab. (BNL), Upton, NY (United States)

    1988-07-11

    The objectives of this study are to: review rf system requirements; review cavity and amplifier hardware; establish basis for revised CDR text and cost estimate; and provide a written summary and technical notes.

  17. The LEP RF Trip and Beam Loss Diagnostics System

    CERN Document Server

    Arnaudon, L; Beetham, G; Ciapala, Edmond; Juillard, J C; Olsen, R

    2002-01-01

    During the last years of operation the number of operationally independent RF stations distributed around LEP reached a total of 40. A serious difficulty when running at high energy and high beam intensities was to establish cause and effect in beam loss situations, where the trip of any single RF station would result in beam loss, rapidly producing further multiple RF station trips. For the last year of operation a fast post-mortem diagnostics system was developed to allow precise time-stamping of RF unit trips and beam intensity changes. The system was based on eight local DSP controlled fast acquisition and event recording units, one in each RF sector, connected to critical RF control signals and fast beam intensity monitors and synchronised by GPS. The acquisition units were armed and synchronised at the start of each fill. At the end of the fill the local time-stamped RF trip and beam intensity change history tables were recovered, events ordered and the results stored in a database for subsequent analys...

  18. High power RF systems for the BNL ERL project

    Energy Technology Data Exchange (ETDEWEB)

    Zaltsman, A.; Lambiase, R.

    2011-03-28

    The Energy Recovery Linac (ERL) project, now under construction at Brookhaven National Laboratory, requires two high power RF systems. The first RF system is for the 703.75 MHz superconducting electron gun. The RF power from this system is used to drive nearly half an Ampere of beam current to 2 MeV. There is no provision to recover any of this energy so the minimum amplifier power is 1 MW. It consists of 1 MW CW klystron, transmitter and power supplies, 1 MW circulator, 1 MW dummy load and a two-way power splitter. The second RF system is for the 703.75 MHz superconducting cavity. The system accelerates the beam to 54.7 MeV and recovers this energy. It will provide up to 50 kW of CW RF power to the cavity. It consists of 50 kW transmitter, circulator, and dummy load. This paper describes the two high power RF systems and presents the test data for both.

  19. Dual-Hop VLC/RF Transmission System with Energy Harvesting Relay under Delay Constraint

    KAUST Repository

    Rakia, Tamer

    2017-02-09

    In this paper, we introduce a dual-hop visible light communication (VLC) / radio frequency (RF) transmission system to extend the coverage of indoor VLC systems. The relay between the two hops is able to harvest light energy from different artificial light sources and sunlight entering the room. The relay receives data packet over a VLC channel and uses the harvested energy to retransmit it to a mobile terminal over an RF channel. We develop a novel statistical model for the harvested electrical power and analyze the probability of data packet loss. We define a system design parameter (α ∈ [0, 1)) that controls the time dedicated for excess energy harvesting and data packet retransmission. It was found that the parameter has an optimal value which minimizes the packet loss probability. Further more, this optimal value is independent of the RF channel path loss. However, optimal showed inverse dependence on the packet size.

  20. Outage Analysis of Practical FSO/RF Hybrid System With Adaptive Combining

    KAUST Repository

    Rakia, Tamer

    2015-08-01

    Hybrid free-space optical (FSO)/radio-frequency (RF) systems have emerged as a promising solution for high-data-rate wireless transmission. We present and analyze a transmission scheme for the hybrid FSO/RF communication system based on adaptive combining. Specifically, only FSO link is active as long as the instantaneous signal-to-noise ratio (SNR) at the FSO receiver is above a certain threshold level. When it falls below this threshold level, the RF link is activated along with the FSO link and the signals from the two links are combined at the receiver using a dual-branch maximal ratio combiner. Novel analytical expression for the cumulative distribution function (CDF) of the received SNR for the proposed hybrid system is obtained. This CDF expression is used to study the system outage performance. Numerical examples are presented to compare the outage performance of the proposed hybrid FSO/RF system with that of the FSO-only and RF-only systems. © 1997-2012 IEEE.

  1. Collective effects for long bunches in dual harmonic RF systems

    Institute of Scientific and Technical Information of China (English)

    AN Shi-Zhong; Klaus Bongardt; Rudolf Maier; TANG Jing-Yu; ZHANG Tian-Jue

    2008-01-01

    The storage of long bunches for large time intervals needs flattened stationary buckets with a large bucket height.Collective effects from the space charge and resistive impedance are studied by looking at the incoherent particle motion for the matched and mismatched bunches.Increasing the RF amplitude with particle number provides r.m.s wise matching for modest intensities.The incoherent motion of large amplitude particles depends on the details of the RF system.The resulting debunching process is a combination of the too small full RF acceptance together with the mismatch,enhanced by the collective effects.Irregular single particle motion is not associated with the coherent dipole instability.For the stationary phase space distribution of the Hofmann-Pedersen approach and for the dual harmonic RF system,stability limits are presented,which are too low if using realistic input distributions.For single and dual harmonic RF system with d=0.31,the tracking results are shown for intensities,by a factor of 3 above the threshold values.Small resistive impedances lead to coherent oscillations around the equilibrium phase value,as energy loss by resistive impedance is compensated by the energy gain of the RF system.

  2. Simultaneous radiofrequency (RF) heating and magnetic resonance (MR) thermal mapping using an intravascular MR imaging/RF heating system.

    Science.gov (United States)

    Qiu, Bensheng; El-Sharkawy, Abdel-Monem; Paliwal, Vaishali; Karmarkar, Parag; Gao, Fabao; Atalar, Ergin; Yang, Xiaoming

    2005-07-01

    Previous studies have confirmed the possibility of using an intravascular MR imaging guidewire (MRIG) as a heating source to enhance vascular gene transfection/expression. This motivated us to develop a new intravascular system that can perform MR imaging, radiofrequncy (RF) heating, and MR temperature monitoring simultaneously in an MR scanner. To validate this concept, a series of mathematical simulations of RF power loss along a 0.032-inch MRIG and RF energy spatial distribution were performed to determine the optimum RF heating frequency. Then, an RF generator/amplifier and a filter box were built. The possibility for simultaneous RF heating and MR thermal mapping of the system was confirmed in vitro using a phantom, and the obtained thermal mapping profile was compared with the simulated RF power distribution. Subsequently, the feasibility of simultaneous RF heating and temperature monitoring was successfully validated in vivo in the aorta of living rabbits. This MR imaging/RF heating system offers a potential tool for intravascular MR-mediated, RF-enhanced vascular gene therapy.

  3. Mobile Router Testing with Diverse RF Communications Links

    Science.gov (United States)

    Brooks, David; Hoder, Doug; Wilkins, Ryan

    2004-01-01

    This is a short report on demonstrations using Mobile IP and several diverse physical communications links to connect a mobile network to a fixed IPv4 internet. The first section is a description of the equipment used, followed by descriptions of the tests, the theoretical results, and finally conclusions and the actual data.

  4. On the performance of dual-hop FSO/RF systems

    KAUST Repository

    Zedini, Emna

    2016-04-21

    Exact closed-form performance metrics for mixed free-space optical/radio frequency (FSO/RF) communication systems are not available in the literature. This paper presents novel results for the performance analysis of a dual-hop FSO/RF transmission system where the FSO link is modeled by the Gamma-Gamma distribution with pointing error impairments and under heterodyne detection, and the RF link experiences the Nakagami-m fading. Using amplify-and-forward fixed gain relaying, new closed form expressions for the outage probability, the moments, the average bit-error-rate, and the ergodic capacity are obtained in terms of the extended generalized bivariate Meijer\\'s G function. Monte Carlo simulations are provided to confirm the accuracy of the newly proposed results.

  5. Applications of barrier bucket RF systems at Fermilab

    Energy Technology Data Exchange (ETDEWEB)

    Bhat, C.M.; /Fermilab

    2006-03-01

    In recent years, the barrier rf systems have become important tools in a variety of beam manipulation applications at synchrotrons. Four out of six proton synchrotrons at Fermilab are equipped with broad-band barrier rf systems. All of the beam manipulations pertaining to the longitudinal phase space in the Fermilab Recycler (synchrotron used for antiproton storage) are carried out using a barrier system. Recently, a number of new applications of barrier rf systems have been developed- the longitudinal momentum mining, longitudinal phase-space coating, antiproton stacking, fast bunch compression and more. Some of these techniques have been critical for the recent spectacular success of the collider performance at the Fermilab Tevatron. Barrier bunch coalescing to produce bright proton bunches has a high potential to increase proton antiproton luminosity significantly. In this paper, I will describe some of these techniques in detail. Finally, I make a few general remarks on issues related to barrier systems.

  6. Micro Electro Mechanical Systems (MEMS) Micro-Switches for Use in DC, RF, and Optical Applications

    Science.gov (United States)

    Suzuki, Kenichiro

    2002-06-01

    Micromachined micro-switches have stimulated the development of the core infrastructure technology for the next generation communication systems because of their superior performance. They are fabricated by similar silicon micromachined processes, but the switch structure and its characteristics depend on each application. Micro electro mechanical systems (MEMS) technology has been applied to micro relays, RF switches, and optical switches; as a result, optical and mechanical performance has been improved.

  7. OPTIMIZATION ON RF DEVICES DESIGN APPLIED IN WIRELESS COMMUNICATIONS

    Directory of Open Access Journals (Sweden)

    D. H. Covarrubias

    2003-04-01

    Full Text Available Third generation (3G cellular mobile communications demands very strict requirements on transreceptordevices design, in mobile terminal or base station [1].Particularly, in mobile terminal, design requirements of power amplifier indicate the next parameters:High linearity ( 20 dB, maximumoutput power (28 dB, by the way of together carry out with the relationship Carrier to Interference (C/I of 9dB [2]. In this article, we will present the optimum design of these devices that carrying with suchrequirements, furthermore, saving more than 20 % of general power consumption in DC.

  8. Wireless gas detection with a smartphone via rf communication.

    Science.gov (United States)

    Azzarelli, Joseph M; Mirica, Katherine A; Ravnsbæk, Jens B; Swager, Timothy M

    2014-12-23

    Chemical sensing is of critical importance to human health, safety, and security, yet it is not broadly implemented because existing sensors often require trained personnel, expensive and bulky equipment, and have large power requirements. This study reports the development of a smartphone-based sensing strategy that employs chemiresponsive nanomaterials integrated into the circuitry of commercial near-field communication tags to achieve non-line-of-sight, portable, and inexpensive detection and discrimination of gas-phase chemicals (e.g., ammonia, hydrogen peroxide, cyclohexanone, and water) at part-per-thousand and part-per-million concentrations.

  9. On the performance of hybrid RF and RF/FSO dual-hop transmission systems

    KAUST Repository

    Ansari, Imran Shafique

    2013-10-01

    In this work, we present the performance analysis of a dual-branch transmission system composed of a direct radio frequency (RF) link and a dual-hop relay composed of asymmetric RF and free-space optical (FSO) links. The FSO link accounts for pointing errors and both types of detection techniques (i.e. intensity modulation/direct detection (IM/DD) as well as heterodyne detection). The performance is evaluated under the assumption of selection combining (SC) diversity scheme. RF links are modeled by Rayleigh fading distribution whereas the FSO link is modeled by a unified Gamma-Gamma fading distribution. Specifically, we derive new exact closed-form expressions for the cumulative distribution function, probability density function, moment generating function, and moments of the end-to-end signal-to-noise ratio of such systems in terms of the Meijer\\'s G function. We then capitalize on these results to offer new exact closed-form expressions for the outage probability, higher-order amount of fading, average error rate for binary and M-ary modulation schemes, and ergodic capacity, all in terms of Meijer\\'s G functions. © 2013 IEEE.

  10. Longitudinal beam instabilities in a double RF system

    CERN Document Server

    Argyropoulos, Theodoros; Gazis, Evangelos

    Operation with a double RF system is essential for many accelerators in order to increase beam stability, to change the bunch shape or to perform various RF manipulations. This is also the case for the operation of the CERN SPS as the LHC proton injector, where in addition to the main RF system, a fourth harmonic RF system is used in bunch shortening mode in order to increase the synchrotron frequency spread inside the bunch and thus to enhance Landau damping of the collective instabilities. In fact the double RF system operation in the SPS is one of the essential means, together with the controlled longitudinal emittance blow-up to significantly increase the longitudinal instability thresholds (single and multi-bunch) and deliver a good quality beam for the LHC. However, for the HiLumi-LHC (HL-LHC) and LHC injector upgrade (LIU) projects higher beam intensities are required. After all upgrades are in place, the main performance limitations of the LHC injector complex are beam instabilities and high intensity...

  11. Communications Systems for Mobile Robotics

    Energy Technology Data Exchange (ETDEWEB)

    Futterman, J A; Pao, H

    2003-12-08

    Performance Confirmation is the activity by which the Yucca Mountain Project confirms that the engineered and natural containment barriers of this national nuclear waste repository are performing as predicted, so that an eventual decision to close the repository can be made. This activity involves systems that must be inspected and, in some cases, serviced by mobile robots. This paper discusses systems for underground mobile robot communications, including requirements, environments, options, issues, and down-select criteria. We reviewed a variety of systems, including Slotted Waveguide, Powerline Carrier, Leaky Feeder, Photonic Bandgap Fiber, Free-Space Optics, Millimeter Waves, Terahertz Systems, and RF Systems (including IEEE 802.11 a,b, and g, and Ultra-Wideband radio).

  12. Effects of temperature variation on the SLC linac RF system

    Energy Technology Data Exchange (ETDEWEB)

    Decker, F.J.; Akre, R.; Byrne, M.; Farkas, Z.D.; Jarvis, H.; Jobe, K.; Koontz, R.; Mitchell, M.; Pennacchi, R.; Ross, M. [and others

    1995-06-01

    The rf system of the Stanford Linear Collider in California is subjected to daily temperature cycles of up to 15{degrees}C. This can result in phase variations of 15{degrees} at 3 GHz over the 3 km length of the main drive line system. Subsystems show local changes of the order of 3{degrees} over 100 meters. When operating with flat beams and normalized emittances of 0.3*10{sup {minus}5} m-rad in the vertical plane, changes as small as 0.5{degrees} perturb the wakefield tail compensation and make continuous tuning necessary. Different approaches to stabilization of the RF phases and amplitudes are discussed.

  13. RF sources for ITER Ion Cyclotron H and CD system

    Energy Technology Data Exchange (ETDEWEB)

    Kazarian, F., E-mail: fabienne.kazarian@iter.org [ITER Organization, CS 90 046, 13067 Sain-Paul-Les-Durance (France); Beaumont, B.; Arambhadiya, B.; Gassmann, T.; Lamalle, Ph.; Rathi, D. [ITER Organization, CS 90 046, 13067 Sain-Paul-Les-Durance (France); Mukherjee, A.; Ajesh, P.; Machchhar, H.; Patadia, D.; Patel, M.; Rajnish, K.; Singh, R.; Suthar, G.; Trivedi, R. [ITER India, IPR, Bhat, Gandhinagar 382428, Gujarat (India); Kumazawa, R.; Seki, T.; Saito, K.; Kasahara, H.; Mutoh, T. [National Institute for Fusion Science, Toki 509-5292 (Japan)

    2011-10-15

    The Ion Cyclotron Heating and Current Drive (IC H and CD) system for ITER will provide 20 MW to the plasma. The associated Radio Frequency (RF) source system has to be compliant with all operation modes foreseen in that frame. Their specifications are fully described in this paper and constraints on IC RF source components are detailed, in particular concerning the final stage tube of the amplifier. Results of tests performed under a collaborative work at the National Institute for Fusion Science (NIFS) facility are presented. Consequences on the procurement process by ITER India (II) are deduced.

  14. SPLinac Computer Simulations of SC Linac RF Systems with Beam

    CERN Document Server

    Tückmantel, Joachim

    2001-01-01

    The beam in a proton linac is very sensitive to field perturbations in the cavities. Therefore a simulation program was written modeling longitudinal beam dynamics in a realistic composite linac RF system. Fast RF vector sum feedback loops control several cavities with b-dependent transit time factors driven by one transmitter. Modeling of feedback loops covers limited transmitter power and bandwidth and possible loop-delay. Vector sum calibration errors, power splitting errors and scatter in the coupling strength to the cavities are optional as well as beam loading of the pulsing beam. Different modes of mechanical cavity perturbations including Lorentz force detuning can be chosen. A multitude of phase-space representation of bunches as well as RF quantity plots are available, most of them can be assembled as a movie, showing the system dynamics in 'real time'.

  15. Managing Vulnerabilities of Tactical Wireless RF Network Systems: A Case Study

    Directory of Open Access Journals (Sweden)

    Philip Chan

    2011-11-01

    Full Text Available Organisations and individuals benefit when wireless networks are protected. After assessing the risks associated with wireless technologies, organisations can reduce the risks by applying countermeasures to address specific threats and vulnerabilities. These countermeasures include management, operational and technical controls. While these countermeasures will not prevent all penetrations and adverse events, they can be effective in reducing many of the common risks associated with wireless RF networks. Among engineers dealing with different scaled and interconnected engineering systems, such as tactical wireless RF communication systems, there is a growing need for a means of analyzing complex adaptive systems. We propose a methodology based on the systematic resolution of complex issues to manage the vulnerabilities of tactical wireless RF systems. There are is a need to assemble and balance the results of any successful measure, showing how well each solution meets the system’s objectives. The uncertain arguments used and other test results are combined using a form of mathematical theory for their analysis. Systems engineering thinking supports design decisions and enables decision‐makers to manage and assess the support for each solution. In these circumstances, complexity management arises from the many interacting and conflicting requirements of an increasing range of possible parameters. There may not be a single ‘right’ solution, only a satisfactory set of resolutions which this system helps to facilitate. Smart and innovative performance matrixes are introduced using a mathematical Bayesian network to manage, model, calculate and analyse all the potential vulnerability paths in wireless RF networks

  16. Compact rf polarizer and its application to pulse compression systems

    Science.gov (United States)

    Franzi, Matthew; Wang, Juwen; Dolgashev, Valery; Tantawi, Sami

    2016-06-01

    We present a novel method of reducing the footprint and increasing the efficiency of the modern multi-MW rf pulse compressor. This system utilizes a high power rf polarizer to couple two circular waveguide modes in quadrature to a single resonant cavity in order to replicate the response of a traditional two cavity configuration using a 4-port hybrid. The 11.424 GHz, high-Q, spherical cavity has a 5.875 cm radius and is fed by the circularly polarized signal to simultaneously excite the degenerate T E114 modes. The overcoupled spherical cavity has a Q0 of 9.4 ×104 and coupling factor (β ) of 7.69 thus providing a loaded quality factor QL of 1.06 ×104 with a fill time of 150 ns. Cold tests of the polarizer demonstrated good agreement with the numerical design, showing transmission of -0.05 dB and reflection back to the input rectangular WR 90 waveguide less than -40 dB over a 100 MHz bandwidth. This novel rf pulse compressor was tested at SLAC using XL-4 Klystron that provided rf power up to 32 MW and generated peak output power of 205 MW and an average of 135 MW over the discharged signal. A general network analysis of the polarizer is discussed as well as the design and high power test of the rf pulse compressor.

  17. The Ultimate Beam in the LHC 400 MHz RF System

    CERN Document Server

    Tückmantel, J

    2010-01-01

    Recently proposals were made to run LHC with beam currents considerably higher than the so-called ultimate one, since other machines have already operated with even higher beam currents. It seems that it was not generally known that this would require a complete replacement of the RF system, especially the expensive high-power part, probably including the couplers and matched cavities. In this context it was underlined that – apparently also not generally known – already the ultimate current in LHC requires serious upgrades of the (much less expensive) RF system’s low-level part. This caused then doubts on the feasibility of the ultimate current in some people. To clarify the situation, in the present paper we present the facts and try to show the reasons behind in a way understandable also for non-RF specialists.

  18. An architecture for analysis and collection of RF signals used by hand-held devices in computer communications

    OpenAIRE

    Hwa, Chua Guan

    2001-01-01

    This thesis studies the wireless communications aspects of an Internetconnected hand-held device. It reviews the multipath effects of RF propagation and provides a detailed analysis of the Mobitex network protocols. Field experiments were conducted to measure the signal strength of indoor and outdoor reception. A framework for using real-time wireless communications analysis equipment for the collection of this RF signal is designed and discussed. Expected results from the collection of this ...

  19. The Effects of Weather on the Life Time of Wireless Sensor Networks Using FSO/RF Communication

    Directory of Open Access Journals (Sweden)

    F. Nadeem

    2010-06-01

    Full Text Available The increased interest in long lasting wireless sensor networks motivates to use Free Space Optics (FSO link along with radio frequency (RF link for communication. Earlier results show that RF/FSO wireless sensor networks have life time twice as long as RF only wireless sensor networks. However, for terrestrial applications, the effect of weather conditions such as fog, rain or snow on optical wireless communication link is major concern, that should be taken into account in the performance analysis. In this paper, life time performance of hybrid wireless sensor networks is compared to wireless sensor networks using RF only for terrestrial applications and weather effects of fog, rain and snow. The results show that combined hybrid network with three threshold scheme can provide efficient power consumption of 6548 seconds, 2118 seconds and 360 seconds for measured fog, snow and rain events respectively resulting in approximately twice of the life time with only RF link.

  20. Antenna Technology and other Radio Frequency (RF) Communications Activities at the Glenn Research Center in Support of NASA's Exploration Vision

    Science.gov (United States)

    Miranda, Felix A.

    2007-01-01

    NASA s Vision for Space Exploration outlines a very ambitious program for the next several decades of the Space Agency endeavors. Ahead is the completion of the International Space Station (ISS); safely flight the shuttle (STS) until 2010; develop and fly the Crew Exploration Vehicle (Orion) by no later than 2014; return to the moon by no later than 2020; extend human presence across the solar system and beyond; implement a sustainable and affordable human and robotic program; develop supporting innovative technologies, knowledge and infrastructure; and promote international and commercial participation in exploration. To achieve these goals, a series of enabling technologies must be developed or matured in a timely manner. Some of these technologies are: spacecraft RF technology (e.g., high power sources and large antennas which using surface receive arrays can get up to 1 Gbps from Mars), uplink arraying (reduce reliance on large ground-based antennas and high operation costs; single point of failure; enable greater data-rates or greater effective distance; scalable, evolvable, flexible scheduling), software define radio (i.e., reconfigurable, flexible interoperability allows for in flight updates open architecture; reduces mass, power, volume), and optical communications (high capacity communications with low mass/power required; significantly increases data rates for deep space). This presentation will discuss some of the work being performed at the NASA Glenn Research Center, Cleveland, Ohio, in antenna technology as well as other on-going RF communications efforts.

  1. Communication System and Method

    Science.gov (United States)

    Sanders, Adam M. (Inventor); Strawser, Philip A. (Inventor)

    2014-01-01

    A communication system for communicating over high-latency, low bandwidth networks includes a communications processor configured to receive a collection of data from a local system, and a transceiver in communication with the communications processor. The transceiver is configured to transmit and receive data over a network according to a plurality of communication parameters. The communications processor is configured to divide the collection of data into a plurality of data streams; assign a priority level to each of the respective data streams, where the priority level reflects the criticality of the respective data stream; and modify a communication parameter of at least one of the plurality of data streams according to the priority of the at least one data stream.

  2. The Development of the Electrically Controlled High Power RF Switch and Its Application to Active RF Pulse Compression Systems

    Energy Technology Data Exchange (ETDEWEB)

    Guo, Jiquan [Stanford Univ., CA (United States)

    2008-12-01

    In the past decades, there has been increasing interest in pulsed high power RF sources for building high-gradient high-energy particle accelerators. Passive RF pulse compression systems have been used in many applications to match the available RF sources to the loads requiring higher RF power but a shorter pulse. Theoretically, an active RF pulse compression system has the advantage of higher efficiency and compactness over the passive system. However, the key component for such a system an element capable of switching hundreds of megawatts of RF power in a short time compared to the compressed pulse width is still an open problem. In this dissertation, we present a switch module composed of an active window based on the bulk effects in semiconductor, a circular waveguide three-port network and a movable short plane, with the capability to adjust the S-parameters before and after switching. The RF properties of the switch module were analyzed. We give the scaling laws of the multiple-element switch systems, which allow the expansion of the system to a higher power level. We present a novel overmoded design for the circular waveguide three-port network and the associated circular-to-rectangular mode-converter. We also detail the design and synthesis process of this novel mode-converter. We demonstrate an electrically controlled ultra-fast high power X-band RF active window built with PIN diodes on high resistivity silicon. The window is capable of handling multi-megawatt RF power and can switch in 2-300ns with a 1000A current driver. A low power active pulse compression experiment was carried out with the switch module and a 375ns resonant delay line, obtaining 8 times compression gain with a compression ratio of 20.

  3. 基于nRF905的智能封锁雷无线通讯技术%Study on Wireless Communication Technology of Intelligent Blockade Land Mine Based on nRF905

    Institute of Scientific and Technical Information of China (English)

    顾强; 李晓晨; 张亚; 安晓红

    2011-01-01

    This article proposed a method to wireless communication of intelligent blockade landmine based on the radio communication of nRF905. It provided the design scheme and the program flow chart of the communication system on intelligent blockade landmine. For advancing the security and the antijamming performance of data transmission, it adopted AT89S52 as control unit which is a kind of high performance MCU, and realized frequency hopping communication among the nRF905 modules. In this article, it successfully designed the prototype instrument, and did the correlative experiment about antijamming performance, send-receive velocity, effective communication distance. It is proved that the system can realize the data transmission of intelligent blockade landmine effectively.%提出了一种基于无线射频模块nRF905的智能封锁雷无线通讯方法,给出了智能封锁雷通讯系统的设计方案和系统程序流程图.为了提高数据传输的保密性及抗干扰性,采用了高性能单片机AT89S52作为控制部件,实现了nRF905模块之间的跳频通讯.制作了原理样机,并且进行了系统抗干扰性、收发速率、有效通讯距离等室内外相关实验,通过实验证明该系统能够有效地实现智能封锁雷的数据传输.

  4. Design and Implementation of RF Energy Harvesting System for Low-Power Electronic Devices

    Science.gov (United States)

    Uzun, Yunus

    2016-08-01

    Radio frequency (RF) energy harvester systems are a good alternative for energizing of low-power electronics devices. In this work, an RF energy harvester is presented to obtain energy from Global System for Mobile Communications (GSM) 900 MHz signals. The energy harvester, consisting of a two-stage Dickson voltage multiplier circuit and L-type impedance matching circuits, was designed, simulated, fabricated and tested experimentally in terms of its performance. Simulation and experimental works were carried out for various input power levels, load resistances and input frequencies. Both simulation and experimental works have been carried out for this frequency band. An efficiency of 45% is obtained from the system at 0 dBm input power level using the impedance matching circuit. This corresponds to the power of 450 μW and this value is sufficient for many low-power devices. The most important parameters affecting the efficiency of the RF energy harvester are the input power level, frequency band, impedance matching and voltage multiplier circuits, load resistance and the selection of diodes. RF energy harvester designs should be optimized in terms of these parameters.

  5. DEMONSTRATION OF AN ATCA BASED RF CONTROL SYSTEM AT FLASH

    CERN Document Server

    Simrock, S N; Jezynski, T; Koprek, W; Butkowski, L; Jablonski, G W; Jalmuzna, W; Makowski, D R; Piotrowski, A; Czuba, K

    2009-01-01

    Future rf control systems will require simultaneous data acquisition of up to 100 fast ADC channels at sampling rates of around 100 MHz and real time signal processing within a few hundred nanoseconds. At the same time the standardization of Low-Level RF systems are common objectives for all laboratories for cost reduction, performance optimization and machine reliability. Also desirable are modularity and scalability of the design as well as compatibility with accelerator instrumentation needs including the control system. All these requirements can be fulfilled with the new telecommunication standard ATCA when adopted to the domain of instrumentation. We describe the architecture and design of an ATCA based LLRF system for the European XFEL. The operation of a prototype capable of controlling the vectorsum of 24-cavities and providing measurements of forward and reflected power are presented.

  6. RF-Compensated Langmuir Probe Measurements in an IPVD System

    Science.gov (United States)

    Juliano, Daniel R.; Ruzic, David N.

    1998-10-01

    The experimental apparatus consists of a commercial-scale magnetron with an RF coil between the target and substrate holder. This coil creates a secondary inductive plasma that ionizes a significant portion of the sputter flux en route from target to substrate. In order to understand and predict the ionization of the sputter flux arriving at the substrate, Langmuir probe measurements of this secondary inductive plasma were made under various combinations of powers (magnetron and RF), pressures, and working gas mixtures. The probe apparatus is RF-compensated in order to keep the voltage difference between the probe tip and plasma constant throughout the RF cycle. In order to yield accurate measurements in the dirty depositing environment of the IPVD system, the back of probe tip is recessed in a small ceramic tube, preventing shorting. Further, the potential on the probe tip is kept low except during the data-collecting voltage sweeps in order to continuously clean it and maintain stable electrical characterisitics.

  7. A New Interlock Design for the TESLA RF System

    Institute of Scientific and Technical Information of China (English)

    H.Leich; J.Kahl; 等

    2001-01-01

    The RF system for TESLA requires a comprehensive interlock system.Usually interlock systems are organized in a hierarchical way,In order to react to different fault conditions in a fast and flexible manner a nonhierarchical organization seems to be the better solution ,At the TESLA Test Facility (TTF) at DESY we will install a nonhierarchical interlock system that is based on user desgned reprogrammable gate-arrays (FPGA's) which incorporate an embedded microcontroller system.This system could beused later for the TESLA linear collider replacing a strictly hierarchical design.

  8. Advanced quantum communication systems

    Science.gov (United States)

    Jeffrey, Evan Robert

    Quantum communication provides several examples of communication protocols which cannot be implemented securely using only classical communication. Currently, the most widely known of these is quantum cryptography, which allows secure key exchange between parties sharing a quantum channel subject to an eavesdropper. This thesis explores and extends the realm of quantum communication. Two new quantum communication protocols are described. The first is a new form of quantum cryptography---relativistic quantum cryptography---which increases communication efficiency by exploiting a relativistic bound on the power of an eavesdropper, in addition to the usual quantum mechanical restrictions intrinsic to quantum cryptography. By doing so, we have observed over 170% improvement in communication efficiency over a similar protocol not utilizing relativity. A second protocol, Quantum Orienteering, allows two cooperating parties to communicate a specific direction in space. This application shows the possibility of using joint measurements, or projections onto an entangled state, in order to extract the maximum useful information from quantum bits. For two-qubit communication, the maximal fidelity of communication using only separable operations is 73.6%, while joint measurements can improve the efficiency to 78.9%. In addition to implementing these protocols, we have improved several resources for quantum communication and quantum computing. Specifically, we have developed improved sources of polarization-entangled photons, a low-loss quantum memory for polarization qubits, and a quantum random number generator. These tools may be applied to a wide variety of future quantum and classical information systems.

  9. RF-modulated pulsed fiber optic lidar transmitter for improved underwater imaging and communications

    Science.gov (United States)

    Kimpel, F.; Chen, Y.; Fouron, J.-L.; Akbulut, M.; Engin, D.; Gupta, S.

    2011-03-01

    We present results on the design, development and initial testing of a fiber-optic based RF-modulated lidar transmitter operating at 532nm, for underwater imaging application in littoral waters. The design implementation is based on using state-of-the-art high-speed FPGAs, thereby producing optical waveforms with arbitrary digital-RF-modulated pulse patterns with carrier frequencies >= 3GHz, with a repetition rate of 0.5-1MHz, and with average powers >=5W (at 532nm). Use of RF-modulated bursts above 500MHz, instead of single optical pulse lidar detection, reduces the effect of volumetric backscatter for underwater imaging application, leading to an improved signal-to-noise-ratio (SNR) and contrast, for a given range. Initial underwater target detection tests conducted at Patuxent River Naval Air Station, MD, in a large water-tank facility, validates the advantages of this hybrid-lidar-radar (HLR) approach for improved underwater imaging, over a wide range of turbidity levels and both white and black targets. The compact, robust and power-efficient fiber laser architecture lends very well to lidar sensor integration on unmanned-underwater-vehicle (UUV) platforms. HLR transmitters can also provide similar advantages in active-sensing situations dominated by continuous backscatter, e.g. underwater communications, imaging through smoke and fire environment, rotor-craft landing in degraded visual environment, and pointing-tracking of active-EO sensors through fog.

  10. Power Electronics System Communications

    OpenAIRE

    Milosavljevic, Ivana

    1999-01-01

    This work investigates communication issues in high-frequency power converters. A novel control communication network (Power Electronics System Network or PES Net) is proposed for modular, medium and high-power, converters. The network protocol, hardware and software are designed and implemented. The PES Net runs at 125 Mb/s over plastic optical fiber allowing converter switching frequencies in excess of 100 kHz. Communication control is implemented in a fie...

  11. TRANSIENT BEAM LOADING EFFECTS IN RF SYSTEMS IN JLEIC

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Haipeng [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Guo, Jiquan [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Rimmer, Robert A. [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Wang, Shaoheng [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States)

    2016-05-01

    The pulsed electron bunch trains generated from the Continuous Electron Beam Accelerator Facility (CEBAF) linac to inject into the proposed Jefferson Lab Electron Ion Collider (JLEIC) e-ring will produce transient beam loading effects in the Superconducting Radio Frequency (SRF) systems that, if not mitigated, could cause unacceptably large beam energy deviation in the injection capture, or exceed the energy acceptance of CEBAF’s recirculating arcs. In the electron storage ring, the beam abort or ion clearing gaps or uneven bucket filling can cause large beam phase transients in the (S)RF cavity control systems and even beam loss due to Robinson instability. We have first analysed the beam stability criteria in steady state and estimated the transient effect in Feedforward and Feedback RF controls. Initial analytical models for these effects are shown for the design of the JLEIC e-ring from 3GeV to 12GeV.

  12. Development of new S-band RF window for stable high-power operation in linear accelerator RF system

    Science.gov (United States)

    Joo, Youngdo; Lee, Byung-Joon; Kim, Seung-Hwan; Kong, Hyung-Sup; Hwang, Woonha; Roh, Sungjoo; Ryu, Jiwan

    2017-09-01

    For stable high-power operation, a new RF window is developed in the S-band linear accelerator (Linac) RF systems of the Pohang Light Source-II (PLS-II) and the Pohang Accelerator Laboratory X-ray Free-Electron Laser (PAL-XFEL). The new RF window is designed to mitigate the strength of the electric field at the ceramic disk and also at the waveguide-cavity coupling structure of the conventional RF window. By replacing the pill-box type cavity in the conventional RF window with an overmoded cavity, the electric field component perpendicular to the ceramic disk that caused most of the multipacting breakdowns in the ceramic disk was reduced by an order of magnitude. The reduced electric field at the ceramic disk eliminated the Ti-N coating process on the ceramic surface in the fabrication procedure of the new RF window, preventing the incomplete coating from spoiling the RF transmission and lowering the fabrication cost. The overmoded cavity was coupled with input and output waveguides through dual side-wall coupling irises to reduce the electric field strength at the waveguide-cavity coupling structure and the possibility of mode competitions in the overmoded cavity. A prototype of the new RF window was fabricated and fully tested with the Klystron peak input power, pulse duration and pulse repetition rate of 75 MW, 4.5 μs and 10 Hz, respectively, at the high-power test stand. The first mass-produced new RF window installed in the PLS-II Linac is running in normal operation mode. No fault is reported to date. Plans are being made to install the new RF window to all S-band accelerator RF modules of the PLS-II and PAL-XFEL Linacs. This new RF window may be applied to the output windows of S-band power sources like Klystron as wells as the waveguide windows of accelerator facilities which operate in S-band.

  13. Communication system for emergency

    Energy Technology Data Exchange (ETDEWEB)

    Ajioka, Yoshiteru [Shizuoka Prefecture (Japan)

    1996-12-01

    People are apprehensive that a strong earthquake with a magnitude of nearly 8 may occur in Tokai area. The whole area of Shizuoka Prefecture has been specified as the specially strengthened region for earthquake disaster measures. This report outlines the communication system for emergency with respect to atomic disaster caused by an earthquake. Previously, wireless receiving system is stationed in the whole area to simultaneously inform the related news to the residents and so, communications with them are possible at any time by using the system. Since mobile wireless receiving sets are stationed in all town halls, self defense organizations and all the places of refuge, mutual communications are possible. These communication system can be utilized for either earthquake or nuclear disaster. Further, Shizuoka general information network system has been established as a communication system for anti-disaster organization and a wireless network via a communication satellite, ``super bird`` has been constructed in addition to the ground network. Therefore, the two communication routes became usable at emergency and the systems are available in either of nuclear disaster or earthquake. (M.N.)

  14. Emittance-dominated long bunches in dual harmonic RF system

    Institute of Scientific and Technical Information of China (English)

    AN Shi-Zhong; Klaus Bongardt; Rudolf Maier; TANG Jing-Yu; ZHANG Tian-Jue

    2008-01-01

    The storage of long bunches for long time intervals needs flattened stationary buckets with a large bucket height. The longitudinal motion of the initially mismatched beam has been studied for both the single and dual harmonic RF systems. The RF amplitude is determined to be r.m.s wise matched. The bucket height of the single harmonic system is too small even for shorter bunch with only 20% increased energy spread. The Halo formation and even debunching can be seen after a few synchrotron periods for single particles with large amplitude. In the case of small energy spread for a cooled beam, Coulomb interaction cannot be ignored. The external voltage has to be increased to keep the r.m.s bunch length unchanged. The new voltage ratio R(N) simplifies physics for the emittance-dominated bunches with modest particle number N. For the single harmonic system, substantial amount of debunching occurs without increasing the external voltage, but very little if the RF amplitude is doubled. Results from the ORBIT tracking code are presented for the 1 GeV bunch in the HESR synchrotron, part of the GSI FAIR project.

  15. Preparations for Upgrading the RF Systems of the PS Booster

    CERN Document Server

    Albright, Simon; Shaposhnikova, Elena

    2016-01-01

    The accelerators of the LHC injector chain need to be upgraded to provide the HL-LHC beams. The PS Booster, the first synchrotron in the LHC injection chain, uses three different RF systems (first, second and up to tenth harmonic) in each of its four rings. As part of the LHC Injector Upgrade the current ferrite RF systems will be replaced with broadband Finemet cavities, increasing the flexibility of the RF system. A Finemet test cavity has been installed in Ring 4 to investigate its effect on machine performance, especially beam stability, during extensive experimental studies. Due to large space charge impedance Landau damping is lost through most of the cycle in single harmonic operation, but is recovered when using the second harmonic and controlled longitudinal emittance blow-up. This paper compares beam parameters during acceleration with and without the Finemet test cavity. Comparisons were made using beam measurements and simulations with the BLonD code based on a full PS Booster impedance model. Thi...

  16. Serial Peripheral Interface Communication Between MCU EM78P447A and RF Reader IC MF RC530

    Institute of Scientific and Technical Information of China (English)

    YOU Zhi; CHEN Shu-zhen; HUANG Ji-wu

    2005-01-01

    A significant method in the way the MCU EM78P447A manipulates the RF reader IC MF RC530's functions used in RF IC card application is presented. In this paper, RF reader IC MF RC530's SPI compatible interface is introduced. The kernel technologies including SPI connection, software design,register initiation, request-response between the reader IC and the MCU, authentication and the proper format of the key are explained. Adopting the serial peripheral interface is the innovation in the paper. The SPI communication mode proves feasible and precise. Furthermore, in the way we avoid the abuse of parallel interface.

  17. On Secrecy Performance of Mixed RF-FSO Systems

    KAUST Repository

    Lei, Hongjiang

    2017-07-05

    In this work, we study the secrecy performance of a mixed radio frequency-free space optical (RF-FSO) transmission systems. All RF links experience Nakagami-m fading and the FSO link experiences the Gamma-Gamma fading. The effect of pointing error and two types of detection techniques (i.e., heterodyne detection and intensity modulation with direct detection) are considered. We derive closed-form expressions for lower bound of the secrecy outage probability (SOP) and exact average secrecy capacity (ASC). Furthermore, by utilizing the expansion of Meijer\\'s G-function, asymptotic results for SOP and ASC are derived when the electrical signal-to-noise ratio of the FSO link tends to infinity. Numerical and Monte-Carlo simulation results are provided to verify the accuracy of our proposed results.

  18. SRF and RF systems for LEReC Linac

    Energy Technology Data Exchange (ETDEWEB)

    Belomestnykh, S. [Brookhaven National Lab. (BNL), Upton, NY (United States); Stony Brook Univ., NY (United States); Ben-Zvi, I. [Brookhaven National Lab. (BNL), Upton, NY (United States); Stony Brook Univ., NY (United States); Brutus, J. C. [Brookhaven National Lab. (BNL), Upton, NY (United States); Fedotov, A. [Brookhaven National Lab. (BNL), Upton, NY (United States); McIntyre, G. [Brookhaven National Lab. (BNL), Upton, NY (United States); Polizzo, S. [Brookhaven National Lab. (BNL), Upton, NY (United States); Smith, K. [Brookhaven National Lab. (BNL), Upton, NY (United States); Than, R. [Brookhaven National Lab. (BNL), Upton, NY (United States); Tuozzolo, J. [Brookhaven National Lab. (BNL), Upton, NY (United States); Veshcherevich, V. [Cornell Univ., Ithaca, NY (United States); Wu, Q. [Brookhaven National Lab. (BNL), Upton, NY (United States); Xiao, B. [Brookhaven National Lab. (BNL), Upton, NY (United States); Xu, W. [Brookhaven National Lab. (BNL), Upton, NY (United States); Zaltsman, A. [Brookhaven National Lab. (BNL), Upton, NY (United States)

    2015-05-03

    The Low Energy RHIC electron Cooling (LEReC) is under development at BNL to improve RHIC luminosity at low energies. It will consist of a short electron linac and two cooling sections, one for blue and one for yellow rings. For the first stage of the project, LEReC-I, we will install a 704 MHz superconducting RF cavity and three normal conducting cavities operating at 9 MHz, 704 MHz and 2.1 GHz. The SRF cavity will boost the electron beam energy up to 2 MeV. The warm cavities will be used to correct the energy spread introduced in the SRF cavity. The paper describes layouts of the SRF and RF systems, their parameters and status.

  19. Optimal RF Systems for Lightly Loaded Superconducting Structures

    CERN Document Server

    Zwart, Townsend; Graves, William S; Wang, D; Zolfaghari, Abbi

    2004-01-01

    Recent developments in the field of RF accelerators have created a demand for power amplifiers that can support very high accelerating gradients, 15-25 MV/m, in superconducting structures with extremely low losses. Free electron lasers (FEL’s) with modest beam current, I< 10 uA, or based on energy recovery linacs (ERL’s) may have intrinsic power demands of less than 1 kW/m. We present the design of an amplifier and external tuner system that will efficiently meet this requirement. The RF amplifier, an Inductive Output Tube (IOT), offers high AC/RF efficiency, flexible power output and switching capability without the need for external modulation. The tuner circuit makes use of low loss ferrite phase shifters to create a moderate quality standing wave (Q~100-1000) between the amplifier and the superconducting cavity. An alternative design based on a shorter cavity structure and employing solid state amplifiers is also presented. The expected performance characteristics of both systems are described.

  20. AMPA experimental communications systems

    Science.gov (United States)

    Beckerman, D.; Fass, S.; Keon, T.; Sielman, P.

    1982-01-01

    The program was conducted to demonstrate the satellite communication advantages of Adaptive Phased Array Technology. A laboratory based experiment was designed and implemented to demonstrate a low earth orbit satellite communications system. Using a 32 element, L-band phased array augmented with 4 sets of weights (2 for reception and 2 for transmission) a high speed digital processing system and operating against multiple user terminals and interferers, the AMPA system demonstrated: communications with austere user terminals, frequency reuse, communications in the face of interference, and geolocation. The program and experiment objectives are described, the system hardware and software/firmware are defined, and the test performed and the resultant test data are presented.

  1. Experience with the LEP Superconducting RF Accelerating System

    CERN Document Server

    Geschonke, Günther

    1998-01-01

    CERN is presently upgrading the large Electron Positron Collider (LEP) to higher energy by installing superconducting RF accelerating cavities. For a total installed circumferential voltage of about 2800 MV, 272 cavities operating at 352 MHz will be needed, representing an active length of 462 m and a cold surface of more than 1600 m2. The series production cavities are made out of copper, sputter-coated with a thin layer of niobium and cooled with liquid He to 4.5 K. The cavities are produced by industry and the acceptance testing is done at CERN. In 1996, 176 cavities had been installed and run successfully at their design gradient of 6 MV/m during physics at a beam energy of 86 GeV. As RF power sources 36 klystrons will finally be installed with a nominal RF output power of 1 MW each. In this paper the superconducting accelerating system in LEP will be described and experience gained during operation for physics as well as new developments will be presented.

  2. The LHC RF System - Experience with beam operation

    CERN Document Server

    Baudrenghien, P; Argyropoulos, T; Arnaudon, L; Bohl, T; Brunner, O; Butterworth, A; Ciapala, E; Dubouchet, F; Esteban-Muller, J; Ferreira-Bento, J; Glenat, D; Hagmann, G; Hofle, W; Jacquet, D; Jaussi, M; Kouzue, S; Landre, D; Lollierou, J; Maesen, P; Martinez Yanez, P; Mastoridis, T; Molendijk, J; Nicou, C; Noirjean, J; Papotti, G; Pashnin, A; Pechaud, G; Pradier, J; Sanchez-Quesada, J; Shaposhnikova, E; Schokker, M; Stellfeld, D; Tuckmantel, J; Valuch, D; Wehrle, U; Weierud, F

    2011-01-01

    The LHC RF system commissioning with beam and physics operation for 2010 and 2011 are presented. It became clear in early 2010 that RF noise was not a lifetime limiting factor: the crossing of the much feared 50 Hz line for the synchrotron frequency did not affect the beam. The broadband LHC RF noise is reduced to a level that makes its contribution to beam diffusion in physics well below that of Intra Beam Scattering. Capture losses are also under control, at well below 0.5%. Longitudinal emittance blow-up, needed for ramping of the nominal intensity single bunch, was rapidly commissioned. In 2011, 3.5 TeV/beam physics has been conducted with 1380 bunches at 50 ns spacing, corresponding to 55% of the nominal current. The intensity per bunch (1.3 1011 p) is significantly above the nominal 1.15 1011. By August 2011 the LHC has accumulated more than 2 fb-1 integrated luminosity, well in excess of the 1 fb-1 target for 2011.

  3. CERN LINAC4 H- Source and SPL plasma generator RF systems, RF power coupling and impedance measurements

    CERN Document Server

    Paoluzzi, M; Marques-Balula, J; Nisbet, D

    2010-01-01

    In the LINAC4 H- source and the SPL plasma generator at CERN, the plasma is heated by a 100 kW, 2 MHz RF system. Matching of the load impedance to the final amplifier is achieved with a resonant network. The system implements a servo loop for power stabilization and frequency hopping to cope with the detuning effects induced by the plasma. This paper provides a detailed description of the system, including the pulse rate increase to 50 Hz for use in the SPL plasma generator. The performances, measurements of RF power coupling, contribution of the plasma to the impedance as well as first operation are reported.

  4. Fundamental Study of a Combined Hyperthermia System with RF Capacitive Heating and Interstitial Heating

    OpenAIRE

    Saitoh, Yoshiaki; Hori, Junichi; 斉藤, 義明; 堀, 潤一

    2001-01-01

    Interstitial RF heating with an inserted electrode allows the heating position selection in a subject, but the narrow heating region is problematic. This study elucidates development of new interstitial RF heating methods, combining with external RF heating using paired electrodes, heating the subject broadly in advance in order to selectively extend the heating region. Two kinds of heating system were developed by controlling a differential mode and a common mode of RF currents. Heating expe...

  5. Fundamental Study of a Combined Hyperthermia System with RF Capacitive Heating and Interstitial Heating

    OpenAIRE

    Saitoh, Yoshiaki; Hori, Junichi; 斉藤, 義明; 堀, 潤一

    2001-01-01

    Interstitial RF heating with an inserted electrode allows the heating position selection in a subject, but the narrow heating region is problematic. This study elucidates development of new interstitial RF heating methods, combining with external RF heating using paired electrodes, heating the subject broadly in advance in order to selectively extend the heating region. Two kinds of heating system were developed by controlling a differential mode and a common mode of RF currents. Heating expe...

  6. High Gradient Operation with the CEBAF Upgrade RF Control System

    Energy Technology Data Exchange (ETDEWEB)

    J. Hovater; G. Davis; Hai Dong; Alicia Hofler; Lawrence King; John Musson; Tomasz Plawski

    2006-08-16

    The CEBAF Accelerator at Jefferson Lab is presently a 6 GeV five pass electron accelerator consisting of two superconducting linacs joined by independent magnetic transport arcs. Energy will be upgraded to 12 GeV with the addition of 10 new high gradient cryomodules (17+ MV/m). The higher gradients pose significant challenges beyond what the present analog low level RF (LLRF) control systems can handle reliably; therefore, a new LLRF control system is needed. A prototype system has been developed incorporating a large FPGA and using digital down and up conversion to minimize the need for analog components. The new system is more flexible and less susceptible to drifts and component nonlinearities. Because resonance control is critical to reach high gradients quickly, the new cryomodules will include a piezoelectric tuner for each cavity, and the LLRF controls must incorporate both feedback and feed-forward methods to achieve optimal resonance control performance. This paper discusses development of the new RF system, system performance for phase and amplitude stability and resonance control under Lorentz detuning measured during recent tests on a prototype cryomodule.

  7. RF H and CD systems for DEMO - Challenges and opportunities

    Energy Technology Data Exchange (ETDEWEB)

    Franke, T.; Wenninger, R. [EFDA Close Support Unit, Boltzmannstr. 2, D - 85748 Garching, Germany and Max-Planck-Institut für Plasmaphysik, EURATOM Association, Boltzmannstr. 2, D - 85748 Garching (Germany); Barbato, E.; Cardinali, A.; Cesario, R.; Mirizzi, F.; Tuccillo, A. A. [Associazione Euratom-ENEA sulla Fusione, C.P. 65-I-00044-Frascati, Rome (Italy); Ceccuzzi, S. [Associazione Euratom-ENEA sulla Fusione, C.P. 65-I-00044-Frascati, Rome, Italy and Applied Electronics Department, Roma Tre University, Via della Vasca Navale, 84 00146, Roma (Italy); Eester, D. V.; Lerche, E. [Association EURATOM-Belgian State, LPP-ERM/KMS, TEC partner, Brussels (Belgium); Mayoral, M.-L. [EFDA Close Support Unit, Boltzmannstr. 2, D - 85748 Garching, Germany and Euratom/CCFE Fusion Association, Culham Science Centre, Abingdon, OX14 3DB (United Kingdom); Nightingale, M. [Euratom/CCFE Fusion Association, Culham Science Centre, Abingdon, OX14 3DB (United Kingdom); Noterdaeme, J.-M.; Poli, E.; Zohm, H. [Max-Planck-Institut für Plasmaphysik, EURATOM Association, Boltzmannstr. 2, D - 85748 Garching (Germany)

    2014-02-12

    The aim of driving a sufficient amount of plasma current with an appropriate radial current density profile is considered as one of the key challenges for a tokamak fusion power plant in steady state operation. Furthermore, efficient heating to enable transition to regime of enhanced confinement and to achieve breakeven plasma temperatures as well as MHD control and plasma breakdown assistance are required. In the framework of the EFDA Power Plant Physics and Technology (PPPT) activities, the ability of the Electron cyclotron (EC), Ion Cyclotron (IC) and Lower Hybrid (LH) systems to fulfil these requirements, was studied for a demonstration fusion power plant (DEMO). As boundary condition, a 1D description of the plasma for a pulsed DEMO based on system code studies combined with transport analysis was developed. The predicted 1D plasma parameters were used to calculate the current drive (CD) efficiency of each system and eventually optimised it. As an example, the EC current drive efficiency could be increased strongly by top launch compared to equatorial launch at least by a factor of two. For the IC system, two possible windows of operation for standard and higher frequencies were highlighted, whereby again top launch leads to higher CD-efficiencies. The efficiencies predicted for DEMO for the RF current drive systems will be presented. Finally, gaps in the feasibility of RF systems under DEMO relevant conditions will be identified.

  8. Digital communication system

    Science.gov (United States)

    Monford, L. G., Jr. (Inventor)

    1974-01-01

    A digital communication system is reported for parallel operation of 16 or more transceiver units with the use of only four interconnecting wires. A remote synchronization circuit produces unit address control words sequentially in data frames of 16 words. Means are provided in each transceiver unit to decode calling signals and to transmit calling and data signals. The transceivers communicate with each other over one data line. The synchronization unit communicates the address control information to the transceiver units over an address line and further provides the timing information over a clock line. A reference voltage level or ground line completes the interconnecting four wire hookup.

  9. Advanced Receiver Design for Mitigating Multiple RF Impairments in OFDM Systems: Algorithms and RF Measurements

    Directory of Open Access Journals (Sweden)

    Adnan Kiayani

    2012-01-01

    Full Text Available Direct-conversion architecture-based orthogonal frequency division multiplexing (OFDM systems are troubled by impairments such as in-phase and quadrature-phase (I/Q imbalance and carrier frequency offset (CFO. These impairments are unavoidable in any practical implementation and severely degrade the obtainable link performance. In this contribution, we study the joint impact of frequency-selective I/Q imbalance at both transmitter and receiver together with channel distortions and CFO error. Two estimation and compensation structures based on different pilot patterns are proposed for coping with such impairments. The first structure is based on preamble pilot pattern while the second one assumes a sparse pilot pattern. The proposed estimation/compensation structures are able to separate the individual impairments, which are then compensated in the reverse order of their appearance at the receiver. We present time-domain estimation and compensation algorithms for receiver I/Q imbalance and CFO and propose low-complexity algorithms for the compensation of channel distortions and transmitter IQ imbalance. The performance of the compensation algorithms is investigated with computer simulations as well as with practical radio frequency (RF measurements. The performance results indicate that the proposed techniques provide close to the ideal performance both in simulations and measurements.

  10. The Evolution of Communication Systems

    OpenAIRE

    2010-01-01

    One can study communications by using Shannon's (1948) mathematical theory of communication. In social communications, however, the channels are not "fixed", but themselves subject to change. Communication systems change by communicating information to related communication systems; co-variation among systems if repeated over time, can lead to co-evolution. Conditions for stabilization of higher-order systems are specifiable: segmentation, stratification, differentiation, reflection, and self...

  11. EMC, RF, and Antenna Systems in Miniature Electronic Devices

    DEFF Research Database (Denmark)

    Ruaro, Andrea

    Advanced techniques for the control of electromagnetic interference (EMI) and for the optimization of the electromagnetic compatibility (EMC) performance has been developed under the constraints typical of miniature electronic devices (MED). The electromagnetic coexistence of multiple systems...... and their mutual interaction have been the underlying theme of the work. The research results concern different aspects related to the integration of radio-frequency (RF) electronics in MEDs and hearing instruments (HI). To control internal EMI, a novel near-field parasitic resonator (NFPR) has been researched...

  12. Design of the SNS Normal Conducting Linac RF Control System

    CERN Document Server

    Regan, A; Rohlev, T S; Wang, Y M; Prokop, M S; Thomson, D W; Regan, Amy; Kwon, Sung-il; Rohlev, Tony S.; Wang, Yi-Ming; Prokop, Mark S.; Thomson, David W.

    2000-01-01

    The Spallation Neutron Source (SNS) is being designed for operation in 2004. The SNS is a 1 GeV machine consisting of a combination normal-conducting and super-conducting linac as well as a ring and target area. The linac front end is a 402.5 MHz RFQ being developed by Lawrence Berkeley Lab. The DTL (at 402.5 MHz) and the CCL (at 805 MHz) stages are being developed by Los Alamos National Laboratory. The expected output energy of the DTL is 87 MeV and that of the CCL is 185 MeV. The RF control system under development for the linac is based on the Low Energy Demonstration Accelerator (LEDA) control system with some new features. This paper will discuss the new design approach and its benefits. Block diagrams and circuit specifics will be addressed. The normal conducting RF control system will be described in detail with references to the super-conducting control system where appropriate.

  13. DYMAC communications system

    Energy Technology Data Exchange (ETDEWEB)

    Lindsey, K.A.

    1980-01-01

    The DYMAC Communications System is part of a nuclear safeguards system called DYMAC - short for DYnamic Materials ACcountability - that gathers accountability information at the Los Alamos Scientific Laboratory (LASL) Plutonium Processing Facility. The communications system handles transmissions between data-entry terminals and nondestructive assay (NDA) instruments located in the facility, and a computer located in an adjacent building. System design emphasizes reliability rather than high speed to ensure the integrity of data transmissions. This manual is directed toward the person responsible for maintaining the DYMAC Communication System. It describes the components that make up the communications network, explains how they operate, and gives detailed information about all of the connections. Many of the system components are commercially available; some have been modified at LASL for DYMAC purposes; others were designed and fabricated at LASL. This manual provides circuit diagrams for all of the LASL modifications and LASL-fabricated equipment. In addition, it provides a series of procedures for tracing cables, reconfiguring various parts of the system, testing data transmissions, and troubleshooting malfunctions.

  14. PIC microcontroller-based RF wireless ECG monitoring system.

    Science.gov (United States)

    Oweis, R J; Barhoum, A

    2007-01-01

    This paper presents a radio-telemetry system that provides the possibility of ECG signal transmission from a patient detection circuit via an RF data link. A PC then receives the signal through the National Instrument data acquisition card (NIDAQ). The PC is equipped with software allowing the received ECG signals to be saved, analysed, and sent by email to another part of the world. The proposed telemetry system consists of a patient unit and a PC unit. The amplified and filtered ECG signal is sampled 360 times per second, and the A/D conversion is performed by a PIC16f877 microcontroller. The major contribution of the final proposed system is that it detects, processes and sends patients ECG data over a wireless RF link to a maximum distance of 200 m. Transmitted ECG data with different numbers of samples were received, decoded by means of another PIC microcontroller, and displayed using MATLAB program. The designed software is presented in a graphical user interface utility.

  15. Advances in piezoelectric PZT-based RF MEMS components and systems

    Science.gov (United States)

    Benoit, R. R.; Rudy, R. Q.; Pulskamp, J. S.; Polcawich, R. G.; Bedair, S. S.

    2017-08-01

    There is continuing interest in radio frequency (RF) microelectromechanical system (MEMS) devices due to their ability to offer exceptional RF performance, high linearity and low power consumption. To date, there is an impressive amount of RF MEMS components such as; switches, resonators, varactors, and tunable inductors that have enabled smaller, cheaper and more efficient RF systems. RF MEMS devices contain micromachined components that have the ability to move so that a change in the mechanical state of a device will result in a change to the device’s RF properties. There are many common modes of actuation, including, but not limited to: electrostatic, magnetostatic, piezoelectric, and electrothermal actuation. Although there are attractive aspects and drawbacks to each of these technologies, this paper will focus on advances in the application of piezoelectric actuation, and in particular the use of lead zirconium titanate (PZT), for RF MEMS.

  16. Airborne wireless communication systems, airborne communication methods, and communication methods

    Science.gov (United States)

    Deaton, Juan D [Menan, ID; Schmitt, Michael J [Idaho Falls, ID; Jones, Warren F [Idaho Falls, ID

    2011-12-13

    An airborne wireless communication system includes circuitry configured to access information describing a configuration of a terrestrial wireless communication base station that has become disabled. The terrestrial base station is configured to implement wireless communication between wireless devices located within a geographical area and a network when the terrestrial base station is not disabled. The circuitry is further configured, based on the information, to configure the airborne station to have the configuration of the terrestrial base station. An airborne communication method includes answering a 911 call from a terrestrial cellular wireless phone using an airborne wireless communication system.

  17. On the performance of hybrid RF and RF/FSO fixed gain dual-hop transmission systems

    KAUST Repository

    Ansari, Imran Shafique

    2013-04-01

    In this work, we present the performance analysis of a dual-branch transmission system composed of a direct radio frequency (RF) link and a dual-hop relay composed of asymmetric RF and free-space optical (FSO) links and compare it without having a direct RF path to see the effects of diversity on our system. The FSO link accounts for pointing errors and both types of detection techniques (i.e. indirect modulation/direct detection (IM/DD) as well as heterodyne detection). The performance is evaluated under the assumption of selection combining diversity scheme. RF links are modeled by Rayleigh fading distribution whereas the FSO link is modeled by a unified Gamma-Gamma fading distribution. Specifically, we derive new exact closed-form expressions for the cumulative distribution function, probability density function, moment generating function, and moments of the end-to-end signal-to-noise ratio of these systems in terms of the Meijer\\'s G function. We then capitalize on these results to offer new exact closed-form expressions for the outage probability, higher-order amount of fading, average error rate for binary and M-ary modulation schemes, and ergodic capacity, all in terms of Meijer\\'s G functions. All our new analytical results are also verified via computer-based Monte-Carlo simulations. © 2013 IEEE.

  18. A HIGH STABILITY, LOW NOISE RF DISTRIBUTION SYSTEM

    Energy Technology Data Exchange (ETDEWEB)

    Bernstein, Dorel

    2002-08-20

    Next generation linear colliders require high stability, low noise distribution of RF phase and timing signals. We describe a fiber-optics system that transmits phase at 357MHz, at a 1500nm wavelength, over a distance of 15 kilometers. Phase length errors in the transmission fiber are measured using the phase of the signal reflected from the fiber end. Corrections are performed by controlling the temperature of a 6-kilometer fiber spool placed in series with the main transmission fiber. This system has demonstrated a phase stability better than 10 femtoseconds per degree C, per kilometer, an improvement of a factor of >2000 relative to un-stabilized fiber. This system uses standard low cost telecom fiber and components.

  19. LCLS-II high power RF system overview and progress

    Energy Technology Data Exchange (ETDEWEB)

    Yeremian, Anahid Dian

    2015-10-07

    A second X-ray free electron laser facility, LCLS-II, will be constructed at SLAC. LCLS-II is based on a 1.3 GHz, 4 GeV, continuous-wave (CW) superconducting linear accelerator, to be installed in the first kilometer of the SLAC tunnel. Multiple types of high power RF (HPRF) sources will be used to power different systems on LCLS-II. The main 1.3 GHz linac will be powered by 280 1.3 GHz, 3.8 kW solid state amplifier (SSA) sources. The normal conducting buncher in the injector will use four more SSAs identical to the linac SSAs but run at 2 kW. Two 185.7 MHz, 60 kW sources will power the photocathode dual-feed RF gun. A third harmonic linac section, included for linearizing the bunch energy spread before the first bunch compressor, will require sixteen 3.9 GHz sources at about 1 kW CW. A description and an update on all the HPRF sources of LCLS-II and their implementation is the subject of this paper.

  20. Integrated protection architectures for radars and communication systems

    NARCIS (Netherlands)

    Wanum, M. van; Monni, S.; Vliet, F.E. van

    2010-01-01

    The protection of phased array T/R modules from high input power levels is an important aspect in reducing vulnerability of radars and communication systems RF electronics in modern military platforms. Different categories of threats can damage the sensitive electronics in the phased-array radar,

  1. Theoretical foundations of synchrotron and storage ring RF systems

    CERN Document Server

    Klingbeil, Harald; Lens, Dieter

    2015-01-01

    This course-tested text is an ideal starting point for engineers and physicists entering the field of particle accelerators. The fundamentals are comprehensively introduced, derivations of essential results are provided, and a consistent notation style used throughout the book allows readers to quickly familiarize themselves with the field, providing a solid theoretical basis for further studies.   Emphasis is placed on the essential features of the longitudinal motion of charged particle beams, together with the corresponding RF generation and power amplification devices for synchrotron and storage ring systems. In particular, electrical engineering aspects such as closed-loop control of system components are discussed.   The book also offers a valuable resource for graduate students in physics, electronics engineering, or mathematics looking for an introductory and self-contained text on accelerator physics.

  2. Communication Facilities for Distributed Systems

    Directory of Open Access Journals (Sweden)

    V. Barladeanu

    1997-01-01

    Full Text Available The design of physical networks and communication protocols in Distributed Systems can have a direct impact on system efficiency and reliability. This paper tries to identify efficient mechanisms and paradigms for communication in distributed systems.

  3. RF Based Fishing Vessel Surveillance System: An Integrated Approach

    Directory of Open Access Journals (Sweden)

    C.Pranit Jeba Samuel

    2013-04-01

    Full Text Available Surveillance is a key factor to ensure safety in various fields, here motivity of fishing boats in ocean/sea are monitored for illegal intrusion in other nations boundary. Hence an effective scheme isdesigned to overcome this threat with Global positioning system (GPS which provides dynamic location of fishing vessel in water and microcontroller which competes on GPS and predefined boundary locations to determine whether the boat have crossed the border or not. If so the fisherman is alerted and the message is transmitted to nearby coast guard ships through RF signals at VHF (30-300MHz range which covers wide area. On adumbrated the patrolling units can alert the fisherman from their position or if necessary the entire movement of the fishing vessel could be controlled remotely for trespassing. This measures fixes the cross boundary fishing problems between nations as the fisherman’s are unaware about their position in water.

  4. RF-knockout Extraction System for the CNAO Synchrotron

    CERN Document Server

    Carmignani, Nicola; Serio, Mario; Balbinot, Giovanni; Bressi, Erminia; Caldara, Michele; Pullia, Marco; Bosser, Jacques; Venchi, Giuseppe

    2010-01-01

    The National Centre for Oncological Hadrontherapy (CNAO) is a centre in Italy for the treatment of patients affected by tumours with proton and carbon ions beams accelerated in a synchrotron. The synchrotron extraction method is based on the use of a betatron core. This work aims to verify, through a theoretical study and a simulation, the possibility of using the RF-knockout extraction method exploiting the existing hardware. A simulation program has been written to simulate the extraction system of the synchrotron with the purpose to define the parameters of the radio frequency. Two types of radio frequencies have been compared in order to obtain a constant spill with the minimum ripple: a carrier wave with a frequency and amplitude modulation, and a gaussian narrow band noise modulated in amplitude. Results of the simulation and considerations on the kicker characteristics are presented

  5. RF System for the MICE Demonstration of Ionisation Cooling

    Energy Technology Data Exchange (ETDEWEB)

    Ronald, K.; et al.

    2017-04-01

    Muon accelerators offer an attractive option for a range of future particle physics experiments. They can enable high energy (TeV+) high energy lepton colliders whilst mitigating the difficulty of synchrotron losses, and can provide intense beams of neutrinos for fundamental physics experiments investigating the physics of flavor. The method of production of muon beams results in high beam emittance which must be reduced for efficient acceleration. Conventional emittance control schemes take too long, given the very short (2.2 microsecond) rest lifetime of the muon. Ionisation cooling offers a much faster approach to reducing particle emittance, and the international MICE collaboration aims to demonstrate this technique for the first time. This paper will present the MICE RF system and its role in the context of the overall experiment.

  6. Pattern phenomena in an rf discharge dusty plasma system

    Institute of Scientific and Technical Information of China (English)

    HUANG Feng; YE Maofu; WANG Long

    2006-01-01

    Various dust patterns are observed in an rf discharge dusty plasma system.According to the dust growth process from small to large in size, the formation of different dust patterns can be divided into two stages: the small-particle stage (or dust cloud stage),and the large-particle stage (or dust crystal stage). The evolution relations between different dust patterns with gas pressure changing are investigated. Dust voids, dust acoustic waves and strong turbulence modes are presented at the small-particle stage. The self-organized dust lattices and dust clusters are investigated at the large-particle stage.The static structure of a dust lattice is characterized by means of the pair correlation function. Dust clusters formed by particles with different numbers and the regular evolution of the clusters with gas pressure are also investigated. The packing sequences of dust clusters are verified through two-dimensional confined molecular dynamics simulations.

  7. Electromagnetics of body area networks antennas, propagation, and RF systems

    CERN Document Server

    Werner, Douglas H

    2016-01-01

    The book is a comprehensive treatment of the field, covering fundamental theoretical principles and new technological advancements, state-of-the-art device design, and reviewing examples encompassing a wide range of related sub-areas. In particular, the first area focuses on the recent development of novel wearable and implantable antenna concepts and designs including metamaterial-based wearable antennas, microwave circuit integrated wearable filtering antennas, and textile and/or fabric material enabled wearable antennas. The second set of topics covers advanced wireless propagation and the associated statistical models for on-body, in-body, and off-body modes. Other sub-areas such as efficient numerical human body modeling techniques, artificial phantom synthesis and fabrication, as well as low-power RF integrated circuits and related sensor technology are also discussed. These topics have been carefully selected for their transformational impact on the next generation of body-area network systems and beyo...

  8. Some Aspects of the Moscow Meson Factory DTL RF System Tuning

    Science.gov (United States)

    Kvasha, A. I.

    1997-05-01

    In this paper the consideration of RF system tuning is ot limited by problems of getting of the demanded level of the RF power in a RF load only as it is supposed that the RF system includes in its the full equipment which provides an acceleration of charge particles i.e. a tank, a coupling loop, a feeder line and RF channel with RF amplifiers and power supply. The simple connection of separate parts of this equipment with each other (after their prelemenary autonomous tuning) can sometimes lead to undesirable results such as: -tank detuning due to an interaction between a fast automatic phase control system (APCS) and automatic frequency control system; - a deterioration of an accelerating field stabilization due to an interaction between a fast APCS and a fast automatic amplitude control system; - an overvoltage in the network of the output RF amplifier H/V supply; - an overvoltage in the anode-grid cavity of the RF output amplifier because of "discharge" of an energy, stored in the tank during an RF pulse. Some proposals verified at the MMF DTL which partly exclude above- mentioned undesirable effects are discussed.

  9. RF system models for the CERN Large Hadron Collider with application to longitudinal dynamics

    Energy Technology Data Exchange (ETDEWEB)

    Mastorides, T.; Rivetta, C.; Fox, J.D.; Winkle, D.Van; /SLAC; Baudrenghien, P.; /CERN

    2011-03-03

    The LHC RF station-beam interaction strongly influences the longitudinal beam dynamics, both single bunch and collective effects. Non-linearities and noise generated within the Radio Frequency (RF) accelerating system interact with the beam and contribute to beam motion and longitudinal emittance blowup. Thus, the noise power spectrum of the RF accelerating voltage strongly affects the longitudinal beam distribution. Furthermore, the coupled-bunch instabilities are also directly affected by the RF components and the configuration of the Low Level RF (LLRF) feedback loops. In this work we present a formalism relating the longitudinal beam dynamics with the RF system configurations, an estimation of collective effects stability margins, and an evaluation of longitudinal sensitivity to various LLRF parameters and configurations.

  10. RF Lens-Embedded Massive MIMO Systems: Fabrication Issues and Codebook Design

    Science.gov (United States)

    Kwon, Taehoon; Lim, Yeon-Geun; Min, Byung-Wook; Chae, Chan-Byoung

    2016-07-01

    In this paper, we investigate a radio frequency (RF) lens-embedded massive multiple-input multiple-output (MIMO) system and evaluate the system performance of limited feedback by utilizing a technique for generating a suitable codebook for the system. We fabricate an RF lens that operates on a 77 GHz (mmWave) band. Experimental results show a proper value of amplitude gain and an appropriate focusing property. In addition, using a simple numerical technique--beam propagation method (BPM)--we estimate the power profile of the RF lens and verify its accordance with experimental results. We also design a codebook--multi-variance codebook quantization (MVCQ)--for limited feedback by considering the characteristics of the RF lens antenna for massive MIMO systems. Numerical results confirm that the proposed system shows significant performance enhancement over a conventional massive MIMO system without an RF lens.

  11. System-in-package LTCC platform for 3D RF to millimeter wave

    Science.gov (United States)

    Vähä-Heikkilä, T.; Lahti, M.

    2011-04-01

    This presentation shows recent trends and results in 3D Low Temperature Co-Fired Ceramics (LTCC) modules in applications from RF to millimeter waves. The system-in-package LTCC platform is a true three dimensional module technology. LTCC is a lightweight multi-layer technology having typically 6-20 ceramic layers and metallizations between. The metallization levels i.e different metal layers can be patterned and connected together with metal vias. Passive devices can also be fabricated on LTCC while active devices and other chips are connected with flip-chip, wire bonding or soldering. In addition to passives directly fabricated to LTCC, several different technologies/ chips can be hybrid integrated to the same module. LTCC platform is also well suited for the realization of antenna arrays for microwave and millimeter wave applications. Potential applications are ranging from short range communications to space and radars. VTT has designed, fabricated and characterized microwave and millimeter wave packages for Radio Frequency (RF) Micro Electro Mechanical Systems (MEMS) as well as active devices. Also, several types of system-in-package modules have been realized containing hybrid integrated CMOS and GaAs MMICs and antenna arrays.

  12. System Level Modelling of RF IC in SystemC-WMS

    Directory of Open Access Journals (Sweden)

    Massimo Conti

    2008-06-01

    Full Text Available This paper proposes a methodology for modelling and simulation of RF systems in SystemC-WMS. Analog RF modules have been described at system level only by using their specifications. A complete Bluetooth transceiver, consisting of digital and analog blocks, has been modelled and simulated using the proposed design methodology. The developed transceiver modules have been connected to the higher levels of the Bluetooth stack described in SystemC, allowing the analysis of the performance of the Bluetooth protocol at all the different layers of the protocol stack.

  13. System Level Modelling of RF IC in SystemC-WMS

    Directory of Open Access Journals (Sweden)

    Orcioni Simone

    2008-01-01

    Full Text Available Abstract This paper proposes a methodology for modelling and simulation of RF systems in SystemC-WMS. Analog RF modules have been described at system level only by using their specifications. A complete Bluetooth transceiver, consisting of digital and analog blocks, has been modelled and simulated using the proposed design methodology. The developed transceiver modules have been connected to the higher levels of the Bluetooth stack described in SystemC, allowing the analysis of the performance of the Bluetooth protocol at all the different layers of the protocol stack.

  14. V-band low-noise integrated circuit receiver. [for space communication systems

    Science.gov (United States)

    Chang, K.; Louie, K.; Grote, A. J.; Tahim, R. S.; Mlinar, M. J.; Hayashibara, G. M.; Sun, C.

    1983-01-01

    A compact low-noise V-band integrated circuit receiver has been developed for space communication systems. The receiver accepts an RF input of 60-63 GHz and generates an IF output of 3-6 GHz. A Gunn oscillator at 57 GHz is phaselocked to a low-frequency reference source to achieve high stability and low FM noise. The receiver has an overall single sideband noise figure of less than 10.5 dB and an RF to IF gain of 40 dB over a 3-GHz RF bandwidth. All RF circuits are fabricated in integrated circuits on a Duroid substrate.

  15. RF Head Coil Design with Improved RF Magnetic Near-Fields Uniformity for Magnetic Resonance Imaging (MRI) Systems.

    Science.gov (United States)

    Sohn, Sung-Min; DelaBarre, Lance; Gopinath, Anand; Vaughan, John Thomas

    2014-08-01

    Higher magnetic field strength in magnetic resonance imaging (MRI) systems offers higher signal-to-noise ratio (SNR), contrast, and spatial resolution in MR images. However, the wavelength in ultra-high fields (7 tesla and beyond) becomes shorter than the human body at the Larmor frequency with increasing static magnetic field (B0) of MRI system. At short wavelengths, interference effect appears resulting in non- uniformity of the RF magnetic near-field (B1) over the subject and MR images may have spatially anomalous contrast. The B1 near-field generated by the transverse electromagnetic (TEM) RF coil's microstrip line element has a maximum near the center of its length and falls off towards both ends. In this study, a double trapezoidal shaped microstrip transmission line element is proposed to obtain uniform B1 field distribution by gradual impedance variation. Two multi-channel RF head coils with uniform and trapezoidal shape elements were built and tested with a phantom at 7T MRI scanner for comparison. The simulation and experimental results show stronger and more uniform B1(+) near-field with the trapezoidal shape.

  16. On the performance of hybrid line of sight RF and RF-FSO fixed gain dual-hop transmission systems

    KAUST Repository

    Zedini, Emna

    2014-12-01

    In this work, we carry out a unified performance analysis of a dual-branch transmission system composed of a direct radio-frequency (RF) link and a dual-hop fixed gain relay over the asymmetric links composed of both RF and unified free-space optics (FSO) under the effect of pointing errors. RF links are modeled by the Nakagami-m fading channel and the FSO link by the Gamma-Gamma fading channel subject to both types of detection techniques (i.e. heterodyne detection and intensity modulation with direct detection (IM/DD)). Selection combining (SC) and maximum ratio combining (MRC) diversity schemes are investigated. More specifically, for the SC method, we derive new unified closed-form expressions for the cumulative distribution function (CDF), the probability density function (PDF), the moment generating function (MGF), the moments, the outage probability (OP), the average bit-error rate (BER) of a variety of binary modulations, and the ergodic capacity for end-to-end signal-to-noise ratio (SNR). Additionally, using the MGF-based approach, the evaluation of the OP, the average BER, and the ergodic capacity for the MRC diversity technique can be performed based entirely on the knowledge of the MGF of the output SNR without ever having to compute its statistics (i.e. PDF and CDF). By implementing SC or MRC diversity techniques, we demonstrate a better performance of our system relative to the traditional RF path only. Also, our analysis illustrates MRC as the optimum combing method. All the analytical results are verified via computer-based Monte-Carlo simulations.

  17. RF system modeling and controller design for the European XFEL

    Energy Technology Data Exchange (ETDEWEB)

    Schmidt, Christian

    2011-06-15

    The European XFEL is being constructed at the Deutsche Elektronen Synchrotron DESY to generate intense, ultrashort pulses of highly coherent and monochromatic X-Rays for material science research. X-ray flashes are generated by accelerating electron bunches within superconducting cavities with radio frequency (RF) fields to energies up to 17.5 GeV. The digital control of these fields requires extremely high quality in order to achieve the physical processes of photon generation. DESY offers with FLASH a pilot test facility, allowing to test and develop most necessary components, even before the XFEL is conducted. Current field control is based on a proportional feedback controller in addition to a constant feedforward drive, which do not meet the high requirements of the XFEL. This thesis shows that a model based controller design can achieve the necessary field regulation requirements. A linear, time invariant ''black box model'' is estimated, which characterizes the essential dynamic behavior. This model is not based on physical assumptions, but describes exclusively the transfer behavior of the plant. The acceleration modules are operated in a pulsed mode, in which the RF field must be kept constant for a finite period. The character of the disturbances and variations from pulse-to-pulse, together with the properties of the system, require a combination of controlled feedforward drive and feedback. Generally unpredictable, low frequency pulse-to-pulse variations are suppressed by the feedback controller. The structural design of the complex multivariable feedback controller is given, which constrains the model based design approach to assign the controller parameters only. Estimation of the parameters, which can not be tuned manually, is done by the method of H{sub {infinity}} loop shaping which is often applied in modern control theory. However, disturbances within a pulse are in a high frequency range concerning the short pulse duration

  18. High Operation Efficiency of Semiconductor Electrooptic Modulators in Advanced Lightwave Communication Systems

    Directory of Open Access Journals (Sweden)

    Ahmed Nabih Zaki Rashed

    2012-07-01

    Full Text Available Photonic links have been proposed to transport radio frequency (RF signals over optical fiber communication systems. External optical modulation is commonly used in high performance RF photonic links. The practical use of optical fiber communication systems to transport RF signals is still limited due to high RF signal loss. In order to reduce the RF signal loss, highly efficient modulators are needed. For many applications, modulators with broad bandwidths are required. However, there are applications that require only a narrow bandwidth. For these narrow band applications, the modulation efficiency can be improved through the resonant enhancement technique at the expense of reduced transmission bandwidth. Therefore we have been investigated to get the best performance of the transmission bit rate capacity and product of different semiconductor materials based electrooptic (EO modulators over wide range of the affecting parameters.

  19. The LANSCE 805 MHZ RF System History and Status

    CERN Document Server

    Lynch, Michael; Tallerico, Paul J

    2005-01-01

    The Los Alamos Neutron Science Center (LANSCE) linear accelerator runs at 201.25 MHz for acceleration to 100 MeV. The remainder of the acceleration to 800 MeV is at 805 MHz. This is done with 44 accelerator cavity stages driven by 805 MHz klystrons. Each klystron has a peak power capability of 1.25 MeV. Originally, 97 klystrons were purchased, which was 70 from Varian/CPI and 27 from Litton. The 44 RF systems are laid out in sectors with either 6 or 7 klystrons per sector. The klystrons in each sector are powered from a common HV sytem. The current arrangement uses the Varian/CPI klystrons in 6 of the 7 sectors and Litton klystrons in the remaining sector. With that arrangement there are 38 CPI klystrons installed and 1 spare klystron per sector and 6 Litton klystrons installed in the final sector with 2 spares. The current average life of all of the operating and spare klystrons (52 total) is >112,000 filament hours and >93,000 HV hours. That is three times the typical klystron lifetime today f...

  20. Flip-OFDM for Unipolar Communication Systems

    CERN Document Server

    Fernando, Nirmal; Viterbo, Emanuele

    2011-01-01

    Unipolar communications systems can transmit information using only real and positive signals. This includes a variety of physical channels ranging from optical (fiber or free-space), to RF wireless using amplitude modulation with non-coherent reception, to baseband single wire communications. Unipolar OFDM techniques enable to efficiently compensate frequency selective distortion in the unipolar communication systems. One of the leading examples of unipolar OFDM is asymmetric clipped optical OFDM (ACO-OFDM) originally proposed for optical communications. Flip-OFDM is an alternative approach that was proposed in a patent, but its performance and full potentials have never been investigated in the literature. In this paper, we first compare Flip-OFDM and ACO-OFDM, and show that both techniques have the same performance but different complexities (Flip-OFDM offers 50% saving). We then propose a new detection scheme, which enables to reduce the noise at the Flip-OFDM receiver by almost 3dB. The analytical perfor...

  1. Digital and analog communication systems

    Science.gov (United States)

    Shanmugam, K. S.

    1979-01-01

    The book presents an introductory treatment of digital and analog communication systems with emphasis on digital systems. Attention is given to the following topics: systems and signal analysis, random signal theory, information and channel capacity, baseband data transmission, analog signal transmission, noise in analog communication systems, digital carrier modulation schemes, error control coding, and the digital transmission of analog signals.

  2. Commissioning and Early Operation Experience of the NSLS-II Storage Ring RF System

    Energy Technology Data Exchange (ETDEWEB)

    Gao, F.; Rose, J.; Cupolo, J.; Dilgen, T.; Rose, B.; Gash, W.; Ravindranath, V.; Yeddulla, M.; Papu, J.; Davila, P.; Holub, B.; Tagger, J.; Sikora, R.; Ramirez, G.; Kulpin, J.

    2015-05-03

    The National Synchrotron Light Source II (NSLS-II) is a 3 GeV electron X-ray user facility commissioned in 2014. The storage ring RF system, essential for replenishing energy loss per turn of the electrons, consists of digital low level RF controllers, 310 kW CW klystron transmitters, CESR-B type superconducting cavities, as well as a supporting cryogenic system. Here we will report on RF commissioning and early operation experience of the system for beam current up to 200mA.

  3. Single-Chip Multiple-Frequency RF MEMS Resonant Platform for Wireless Communications Project

    Data.gov (United States)

    National Aeronautics and Space Administration — A novel, single-chip, multiple-frequency platform for RF/IF filtering and clock reference based on contour-mode aluminum nitride (AlN) MEMS piezoelectric resonators...

  4. High-Power Multimode X-Band RF Pulse Compression System for Future Linear Colliders

    Energy Technology Data Exchange (ETDEWEB)

    Tantawi, S.G.; Nantista, C.D.; Dolgashev, V.A.; Pearson, C.; Nelson, J.; Jobe, K.; Chan, J.; Fant, K.; Frisch, J.; /SLAC; Atkinson, D.; /LLNL, Livermore

    2005-08-10

    We present a multimode X-band rf pulse compression system suitable for a TeV-scale electron-positron linear collider such as the Next Linear Collider (NLC). The NLC main linac operating frequency is 11.424 GHz. A single NLC rf unit is required to produce 400 ns pulses with 475 MW of peak power. Each rf unit should power approximately 5 m of accelerator structures. The rf unit design consists of two 75 MW klystrons and a dual-moded resonant-delay-line pulse compression system that produces a flat output pulse. The pulse compression system components are all overmoded, and most components are designed to operate with two modes. This approach allows high-power-handling capability while maintaining a compact, inexpensive system. We detail the design of this system and present experimental cold test results. We describe the design and performance of various components. The high-power testing of the system is verified using four 50 MW solenoid-focused klystrons run off a common 400 kV solid-state modulator. The system has produced 400 ns rf pulses of greater than 500 MW. We present the layout of our system, which includes a dual-moded transmission waveguide system and a dual-moded resonant line (SLED-II) pulse compression system. We also present data on the processing and operation of this system, which has set high-power records in coherent and phase controlled pulsed rf.

  5. COMMUNICATIONS AND INFORMATION SYSTEMS

    Directory of Open Access Journals (Sweden)

    Dănuţ ŢIGĂNUŞ

    2011-01-01

    Full Text Available This essay assesses the communications and information systems (CIS in support of the civilian and military structures deployed in the European Union led crises management operations and missions. The article emphasizes the specific structure and function of CIS taking in consideration the particularities of EU led missions. The integration of the EU institutional networks and systems with the national systems provided by the EU member states is considered a key element. The analysis-part of this paper starts with the specific EU command and control system for crises management missions based on two autonomous solutions and one relying on NATO capabilities. Further, it continues with the challenges of the classifi ed information exchange at the operational theatre level. The most important contribution of this article is based on the long term vision implementation measures for the CIS structure, roles, functions and services provided and the information management infrastructure. CIS deployment mechanisms are described with references to the practical situation of the CIS deployed in support of crises management operations and missions. Two important defi nitions are provided regarding the CIS for crisis management and their roles in the specific EU operational environment. The system view of the operational CIS is depicted and analysed also, with a focus on the integration aspects of the infrastructure as the information transport layer for the information exchange flow. The last part of the article focuses on the CIS functions for the deployed systems which are detailed alongside with the C2 and Information Exchange Requirements in the EU operational environment. The variety of the theoretical approaches to determine the CIS infrastructure for EU-led civilian and military missions triggers the conclusion that the planning and implementation process is extremely complex especially in the context of the new security environment and requires

  6. An Optical Receiver Post-Processing System for the Integrated Radio and Optical Communications Software Defined Radio Test Bed

    Science.gov (United States)

    Nappier, Jennifer M.; Tokars, Roger P.; Wroblewski, Adam C.

    2016-01-01

    The Integrated Radio and Optical Communications (iROC) project at the National Aeronautics and Space Administration's (NASA) Glenn Research Center is investigating the feasibility of a hybrid radio frequency (RF) and optical communication system for future deep space missions. As a part of this investigation, a test bed for a radio frequency (RF) and optical software defined radio (SDR) has been built. Receivers and modems for the NASA deep space optical waveform are not commercially available so a custom ground optical receiver system has been built. This paper documents the ground optical receiver, which is used in order to test the RF and optical SDR in a free space optical communications link.

  7. Introduction to digital communication systems

    CERN Document Server

    Wesolowski, Krzysztof

    2009-01-01

    Combining theoretical knowledge and practical applications, this advanced-level textbook covers the most important aspects of contemporary digital communication systems. Introduction to Digital Communication Systems focuses on the rules of functioning digital communication system blocks, starting with the performance limits set by the information theory. Drawing on information relating to turbo codes and LDPC codes, the text presents the basic methods of error correction and detection, followed by baseband transmission methods, and single- and multi-carrier digital modulations. The basi

  8. Developement of a 6 GHz subsystem for the RF control system of the S-DALINAC

    Energy Technology Data Exchange (ETDEWEB)

    Burandt, Christoph; Araz, Asim; Bonnes, Uwe; Eichhorn, Ralf; Enders, Joachim; Konrad, Martin; Steiner, Bastian; Weiland, Thomas [Institut fuer Kernphysik, Technische Universitaet Darmstadt, Schlossgartenstrasse 9, 64289 Darmstadt (Germany)

    2010-07-01

    A new source of polarized electrons is currently installed at the S-DALINAC. Due to spatial constraints at the existing installation, detailed planning and extensive simulation were done. Results from beam dynamics calculations show the necessity of further bunch compression. The new injector design therefore includes a harmonic prebunching system consisting of two normal conducting copper cavities operated at 3 GHz and 6 GHz respectively. Since the S-DALINAC is exclusively operated at 3 GHz new 6 GHz components have to be developed and need to be integrated into the RF control system. The basic idea of the existing analog control system and the future digital control system is the down conversion of RF signals to the base band. Therefore the low frequency part of each system can be used without adaptions while the RF module requires redevelopment. This talk covers the redesign of the existing 3 GHz RF module for 6 GHz and reports on results obtained with a prototype.

  9. Design and optimization of an RF energy harvesting system from multiple sources

    Science.gov (United States)

    Ali, Mai; Albasha, Lutfi; Qaddoumi, Nasser

    2013-05-01

    This paper presents the design and optimization of an RF energy harvesting system from multiple sources. The RF power is harvested from four frequency bands representing five wireless systems, namely GSM, UMTS, DTV, Wi-Fi, and road tolling system. A Schottky diode model was developed based on which an RF-DC rectifier joined with a voltage multiplier circuits were designed. The simulation results of the complete RF harvesting system showed superior performance to similar state of the art systems. To further optimize the design, and to eliminate use of a non-standard CMOS process associated with Schottky diodes, the Schottky diode based rectifier was replaced by diode connected transistor configuration based on self-threshold cancellation (SVC) technique.

  10. High power RF system for transverse deflecting structure XFEL TDS INJ

    Science.gov (United States)

    Volobuev, E. N.; Zavadtsev, A. A.; Zavadtsev, D. A.; Smirnov, A. J.; Sobenin, N. P.; Churanov, D. V.

    2016-09-01

    The high power RF system (HPRF) is designed for RF feeding of the transverse deflecting structure of the transverse deflecting system XFEL TDS System INJ of the European X-ray Free Electron Laser. The HPRF system includes klystron, waveguide ceramic windows, directional couplers, waveguide vacuum units, spark detector and waveguide line. Operating frequency is 2997.2 MHz. Peak input power is up to 3 MW. The HPRF system has been developed, manufactured and assembled in the XFEL Injector building. The total length of the waveguide line is 55 m from the klystron at the -5 floor to the transverse deflecting structure at the -7 floor. All designed RF parameters have been obtained experimentally at low RF power level.

  11. Communication Systems Analysis Laboratory (CSAL)

    Data.gov (United States)

    Federal Laboratory Consortium — CSAL conducts electronic warfare investigations of radio frequency communication systems with respect to current and emerging electronic warfare threats. CSAL uses...

  12. An RF powering system with adaptive impedance matching for individual health monitoring applications.

    Science.gov (United States)

    Zemin Liu; Yu-Pin Hsu; Hella, Mona M

    2016-08-01

    This paper presents a high-efficiency RF powering system, suitable for individual health monitoring applications. The system is composed of an antenna, an impedance matching network, and a two-stage full-wave RF-DC rectifier. A novel tuning mechanism is proposed to automatically adjust the impedance of the matching network. This mechanism can effectively improve the power efficiency of the system by 47% compared to the case without tuning. For the adaptive impedance, only a 5-bits binary weighted capacitor bank is required in the matching network. The complete system, designed in a standard 0.13μm CMOS technology, converts a -6dBm 915MHz RF signal to a 1.7V DC voltage with an output current of 85μA. The simulated maximum power efficiency of the complete RF harvester is 66%.

  13. Wavelet transform domain communication systems

    Science.gov (United States)

    Orr, Richard S.; Pike, Cameron; Lyall, Michael J.

    1995-04-01

    In this paper we introduce a new class of communications systems called wavelet transform domain (WTD) systems. WTD systems are transmultiplexer (TMUX) structures in which information to be communicated over a channel is encoded, via an inverse discrete wavelet transform (IDWT), as the wavelet coefficients of the transmitted signal, and extracted at the receiver by a discrete wavelet transform (DWT). WTD constructs can be used for covert, or low probability of intercept/detection (LPI/D) communications, baseband bandwidth efficient communications, or code-division multiple access (CDMA). This paper concentrates on the spread spectrum applications.

  14. A Dual-Band Antenna for RF Energy Harvesting Systems in Wireless Sensor Networks

    OpenAIRE

    A. Bakkali; Pelegri-Sebastia, J.; Sogorb, T.; V. Llario; Bou-Escriva, A.

    2016-01-01

    In this paper, we focus on ambient radio frequency energy available from commercial broadcasting stations in order to provide a system based on RF energy harvesting using a new design of receiving antenna. Several antenna designs have been proposed for use in RF energy harvesting systems, as a pertinent receiving antenna design is highly required since the antenna features can affect the amount of energy harvested. The proposed antenna is aimed at greatly increasing the energy harves...

  15. Commissioning and Early Operation for the NSLS-II Booster RF System

    Energy Technology Data Exchange (ETDEWEB)

    Marques, C. [Brookhaven National Lab. (BNL), Upton, NY (United States); Cupolo, J. [Brookhaven National Lab. (BNL), Upton, NY (United States); Davila, P. [Brookhaven National Lab. (BNL), Upton, NY (United States); Gao, F. [Brookhaven National Lab. (BNL), Upton, NY (United States); Goel, A. [Brookhaven National Lab. (BNL), Upton, NY (United States); Holub, B. [Brookhaven National Lab. (BNL), Upton, NY (United States); Kulpin, J. [Brookhaven National Lab. (BNL), Upton, NY (United States); McDonald, K. [Brookhaven National Lab. (BNL), Upton, NY (United States); Oliva, J. [Brookhaven National Lab. (BNL), Upton, NY (United States); Papu, J. [Brookhaven National Lab. (BNL), Upton, NY (United States); Ramirez, G. [Brookhaven National Lab. (BNL), Upton, NY (United States); Rose, J. [Brookhaven National Lab. (BNL), Upton, NY (United States); Sikora, R. [Brookhaven National Lab. (BNL), Upton, NY (United States); Sorrentino, C. [Brookhaven National Lab. (BNL), Upton, NY (United States); Towne, N. [Brookhaven National Lab. (BNL), Upton, NY (United States)

    2015-05-03

    The National Synchrotron Light Source II (NSLS-II) at Brookhaven National Laboratory (BNL) is a third generation 3GeV, 500mA synchrotron light source. We discuss the booster synchrotron RF system responsible for providing power to accelerate an electron beam from 200MeV to 3GeV. The RF system design and construction are complete and is currently in the operational phase of the NSLS-II project. Preliminary operational data is also discussed.

  16. Wireless Environment Monitoring System Based on DSP and nRF24L01%基于DSP和nRF24L01的无线环境监测系统设计

    Institute of Scientific and Technical Information of China (English)

    郝文延; 焦明华

    2011-01-01

    设计基于DSP(Digital Signal Processor)和nRF24L01的无线环境监测系统.系统的主拉部件选用的是TMS320LF2407,无线通信模块选用的是nRF24L01.文中论述了系统各硬件模块的选择方案,给出了各部分的软件设计.实验表明,该系统可以实现对环境温度、光照强度等的无线监测.%This paper designs a wireless environmental monitoring system based on DSP and nRF24L01. TMS320LF2407 is used as the main control unit, and nRF24L01 is used as the wireless communication module. Design plans of system hardware modules are discussed , and the software designs are given. Experiment results show the system realizes the wireless monitoring of the environment temperature and light intensity.

  17. Low Voltage Totally Free Flexible RF MEMS Switch With Anti-Stiction System

    CERN Document Server

    Touati, Salim; Kanciurzewski, Alexandre; Robin, Renaud; Rollier, A -S; Millet, Olivier; Segueni, Karim

    2008-01-01

    This paper concerns a new design of RF MEMS switch combined with an innovative process which enable low actuation voltage (<5V) and avoid stiction. First, the structure described with principal design issues, the corresponding anti-stiction system is presented and FEM simulations are done. Then, a short description of the process flow based on two non polymer sacrificial layers. Finally, RF measurements are presented and preliminary experimental protocol and results of anti-stiction validation is detailed. Resulting RF performances are -30dB of isolation and -0.45dB of insertion loss at 10 GHz.

  18. Communications device identification methods, communications methods, wireless communications readers, wireless communications systems, and articles of manufacture

    Science.gov (United States)

    Steele, Kerry D [Kennewick, WA; Anderson, Gordon A [Benton City, WA; Gilbert, Ronald W [Morgan Hill, CA

    2011-02-01

    Communications device identification methods, communications methods, wireless communications readers, wireless communications systems, and articles of manufacture are described. In one aspect, a communications device identification method includes providing identification information regarding a group of wireless identification devices within a wireless communications range of a reader, using the provided identification information, selecting one of a plurality of different search procedures for identifying unidentified ones of the wireless identification devices within the wireless communications range, and identifying at least some of the unidentified ones of the wireless identification devices using the selected one of the search procedures.

  19. MEMS-based Circuits and Systems for Wireless Communication

    CERN Document Server

    Kaiser, Andreas

    2013-01-01

    MEMS-based Circuits and Systems for Wireless Communication provides comprehensive coverage of RF-MEMS technology from device to system level. This edited volume places emphasis on how system performance for radio frequency applications can be leveraged by Micro-Electro-Mechanical Systems (MEMS). Coverage also extends to innovative MEMS-aware radio architectures that push the potential of MEMS technology further ahead.  This work presents a broad overview of the technology from MEMS devices (mainly BAW and Si MEMS resonators) to basic circuits, such as oscillators and filters, and finally complete systems such as ultra-low-power MEMS-based radios. Contributions from leading experts around the world are organized in three parts. Part I introduces RF-MEMS technology, devices and modeling and includes a prospective outlook on ongoing developments towards Nano-Electro-Mechanical Systems (NEMS) and phononic crystals. Device properties and models are presented in a circuit oriented perspective. Part II focusses on ...

  20. Realistic RF system and Beam Simulation in Real Time for a Synchrotron

    CERN Document Server

    Tückmantel, Joachim

    2001-01-01

    Due to heavy beam loading with gaps in the LHC beams, RF and beam are intimately linked to a complex system with fast transients where the RF loops and their limitations play a decisive role. Such a system is difficult to assess with analytical methods. To learn about overall system stability and for the definition of RF components to be built it is essential to understand the complete system long before the machine really exists. Therefore the author has written a general purpose real time simulation program and applied it to model the LHC machine with its beam pattern and complete double RF system. The latter is equipped with fast RF vector feedback loops having loop delay, transmitter power limitation and limited amplifier bandwidth as well as including one-turn-delay feedback and longitudinal batch injection damping. The development of all RF and beam quantities can be displayed graphically turn by turn. These frames can be assembled to a realistic multi-trace scope movie.

  1. RF system concepts for a muon cooling experiment

    Energy Technology Data Exchange (ETDEWEB)

    Turner, W.C.; Corlett, J.N.; Li, D. [Lawrence Berkeley National Lab., CA (United States); Moretti, A. [Fermi National Accelerator Lab., Batavia, IL (United States); Kirk, H.G.; Palmer, R.B.; Zhao, Y. [Brookhaven National Lab., Upton, NY (United States)

    1998-06-01

    The feasibility of muon colliders for high energy physics experiments has been under intensive study for the past few years and recent activity has focused on defining an R and D program that would answer the critical issues. An especially critical issue is developing practical means of cooling the phase space of the muons once they have been produced and captured in a solenoidal magnetic transport channel. Concepts for the rf accelerating cavities of a muon cooling experiment are discussed.

  2. Integrated Inductors for RF Transmitters in CMOS/MEMS Smart Microsensor Systems

    Science.gov (United States)

    Kim, Jong-Wan; Takao, Hidekuni; Sawada, Kazuaki; Ishida, Makoto

    2007-01-01

    This paper presents the integration of an inductor by complementary metal-oxide-semiconductor (CMOS) compatible processes for integrated smart microsensor systems that have been developed to monitor the motion and vital signs of humans in various environments. Integration of radio frequency transmitter (RF) technology with complementary metal-oxide-semiconductor/micro electro mechanical systems (CMOS/MEMS) microsensors is required to realize the wireless smart microsensors system. The essential RF components such as a voltage controlled RF-CMOS oscillator (VCO), spiral inductors for an LC resonator and an integrated antenna have been fabricated and evaluated experimentally. The fabricated RF transmitter and integrated antenna were packaged with subminiature series A (SMA) connectors, respectively. For the impedance (50 Ω) matching, a bonding wire type inductor was developed. In this paper, the design and fabrication of the bonding wire inductor for impedance matching is described. Integrated techniques for the RF transmitter by CMOS compatible processes have been successfully developed. After matching by inserting the bonding wire inductor between the on-chip integrated antenna and the VCO output, the measured emission power at distance of 5 m from RF transmitter was -37 dBm (0.2 μW).

  3. An Implantable Cardiovascular Pressure Monitoring System with On-Chip Antenna and RF Energy Harvesting

    Directory of Open Access Journals (Sweden)

    Yu-Chun Liu

    2015-08-01

    Full Text Available An implantable wireless system with on-chip antenna for cardiovascular pressure monitor is studied. The implantable device is operated in a batteryless manner, powered by an external radio frequency (RF power source. The received RF power level can be sensed and wirelessly transmitted along with blood pressure signal for feedback control of the external RF power. The integrated electronic system, consisting of a capacitance-to-voltage converter, an adaptive RF powering system, an RF transmitter and digital control circuitry, is simulated using a TSMC 0.18 μm CMOS technology. The implanted RF transmitter circuit is combined with a low power voltage-controlled oscillator resonating at 5.8 GHz and a power amplifier. For the design, the simulation model is setup using ADS and HFSS software. The dimension of the antenna is 1 × 0.6 × 4.8 mm3 with a 1 × 0.6 mm2 on-chip circuit which is small enough to place in human carotid artery.

  4. Smart home system based on BOA and nRF24L01%基于 BOA 和 nRF24L01的智能家居系统

    Institute of Scientific and Technical Information of China (English)

    窦慧晶; 侯荣全; 陈凤菊

    2015-01-01

    Aiming at the shortcomings of ZigBee and Z-Wave at present wireless communication technology in smart home,this paper presents a smart home system based on the BOA and nRF24L01.The home gateway is based on S3C2440 and Linux operation system.Within the family,nRF24L01 is used to communicate.Each wireless node is de-signed from environmental monitoring,home control,and home security three aspects.In order to fully understand the performance of the system,the system is tested in modular.Experimental results show that the system can achieve the desired result and bring convenience to people's family life.%针对目前智能家居方面比较流行的 ZigBee 和 Z-Wave 无线通信技术的一些不足,提出了一种基于 BOA 和 nRF24L01的智能家居系统,其家庭网关部分以 S3C2440为核心,Linux 为实时操作系统,家庭内部各个节点采用无线射频模块nRF24L01通信,各无线节点从环境监测、家电控制和家庭安防3个方面来设计。为了全面了解系统的性能,对系统进行了分模块的测试。实验结果表明,系统能够达到预期的结果,能够给人们的家庭生活带来方便。

  5. Underwater wireless communication system

    Energy Technology Data Exchange (ETDEWEB)

    Goh, J H; Shaw, A; Al-Shamma' a, A I, E-mail: j.h.goh@2006.ljmu.ac.u [Liverpool John Moores University, General Engineering Research Institute (GERI), RF and Microwave Group, Byrom Street, Liverpool, L3 3AF (United Kingdom)

    2009-07-01

    Underwater communication has a range of applications including remotely operated vehicle (ROV) and autonomous underwater vehicle (AUV) communication and docking in the offshore industry. Current underwater transmission techniques is primarily utilise sound waves for large distance at lower frequencies and the velocity of sound in water is approximately 1500m/s the resultant communications have problems with multi-path propagation and low bandwidth problems. The use of electromagnetic (EM) techniques underwater has largely been overlooked because of the attenuation due to the conductivity of seawater. However, for short range applications, the higher frequencies and much higher velocity can prove advantageous. This paper will outline a project which will utilise recent investigations that demonstrate EM wave propagation up to the MHz frequency range is possible in seawater.

  6. On Building Secure Communication Systems

    DEFF Research Database (Denmark)

    Carvalho Quaresma, Jose Nuno

    This thesis presents the Guided System Development (GSD) framework, which aims at supporting the development of secure communication systems. A communication system is specified in a language similar to the Alice and Bob notation, a simple and intuitive language used to describe the global...... perspective of the communications between different principals. The notation used in the GSD framework extends that notation with constructs that allow the security requirements of the messages to be described. From that specification, the developer is guided through a semi-automatic translation that enables...... into code that implements the communication skeleton of the system and can then be used by the system designer. New output languages can also easily be added to the GSD framework. Additionally, a prototype of the GSD framework was implemented and an ex-ample of using the GSD framework in a real world system...

  7. Communication, Work Systems and HRD

    Science.gov (United States)

    Pace, R. Wayne

    2013-01-01

    Purpose: The purpose of this article is to show the foundational place that communication theory and its practice occupies in functioning work systems. Design/methodology/approach: This paper defines the word communication in terms of the creation and interpretation of displays, describes what it means to have a theoretical foundation for a…

  8. SIMULATIVE ANALYSIS OF OSNR AND RECEIVED ELECTRIC RF POWER OF A ROF SYSTEM HAVING VARIABLE FIBER LENGTH, USING DIFFERENT MODULATION TECHNIQUES AND OPTICAL AMPLIFIERS

    Directory of Open Access Journals (Sweden)

    KARANBIR SINGH,

    2011-05-01

    Full Text Available In this paper, we analyzed OSNR and received electric RF power of a RoF communication system having variable fiber length, using direct and external modulation techniques and different optical amplifiers. In this work, we have compared and measured the OSNR and received optical power of the RoF system for different modulation techniques, i.e. direct and external modulation. Further, we also compared the received electric RF power for variable fiber lengths for direct and external modulation using different optical amplifiers, i.e. EDFAand SOA. We observe an increase of –11 dB (approx. in the received RF power for External modulation compared to direct modulation with EDFA.

  9. Multiantenna systems for MIMO communications

    CERN Document Server

    DeFlaviis, Franco

    2008-01-01

    Advanced communication scenarios demand the development of new systemswhere antenna theory, channel propagation and communication models are seen from a common perspective as a way to understand and optimize the system as a whole. In this context, a comprehensive multiantenna formulation for multiple-input multiple-output systems is presented with a special emphasis on the connection of the electromagnetic and communication principles.Starting from the capacity for amultiantenna system, the book reviews radiation, propagation, and communicationmechanisms, paying particular attention to the vec

  10. Integrated Inductors for RF Transmitters in CMOS/MEMS Smart Microsensor Systems

    Directory of Open Access Journals (Sweden)

    Makoto Ishida

    2007-07-01

    Full Text Available This paper presents the integration of an inductor by complementary metal-oxide-semiconductor (CMOS compatible processes for integrated smart microsensorsystems that have been developed to monitor the motion and vital signs of humans invarious environments. Integration of radio frequency transmitter (RF technology withcomplementary metal-oxide-semiconductor/micro electro mechanical systems (CMOS/MEMS microsensors is required to realize the wireless smart microsensors system. Theessential RF components such as a voltage controlled RF-CMOS oscillator (VCO, spiralinductors for an LC resonator and an integrated antenna have been fabricated and evaluatedexperimentally. The fabricated RF transmitter and integrated antenna were packaged withsubminiature series A (SMA connectors, respectively. For the impedance (50 matching,a bonding wire type inductor was developed. In this paper, the design and fabrication of thebonding wire inductor for impedance matching is described. Integrated techniques for theRF transmitter by CMOS compatible processes have been successfully developed. Aftermatching by inserting the bonding wire inductor between the on-chip integrated antennaand the VCO output, the measured emission power at distance of 5 m from RF transmitterwas -37 dBm (0.2 μW.

  11. New developments in RF power and polarization measurements on the ECH System on DIII-D

    Science.gov (United States)

    Cengher, M.; Lohr, J.; Gorelov, Y.; Moeller, C. P.; Ponce, D.; Torrezan, A.

    2016-10-01

    The rf power injected at the tokamak by the electron cyclotron heating (ECH) system is measured and calibrated on a shot to shot basis for the six 110 GHz, 1 MW class gyrotrons. A new technique for ECH power measurement at the tokamak using a 4-port rf monitor was tested. Polarization scans for each system show H-plane and E-plane rf waveforms can be combined to provide a reliable calibrated power signal at the closest access point near the tokamak. Previous attempts to calibrate the power at this end were limited by the pickup of only one polarization angle at the last miter bend. Calorimetric measurements in the relevant gyrotron cooling circuits in conjunction with the 4-port RF monitors with orthomode transducers can be used to calibrate the rf power. Other alternative approaches showing proportionality with the input power like the inline power monitor and in-vessel measurements are discussed. Future plans include mode content measurements at the tokamak end of the transmission line using the 4-port RF monitors and mode sensitive directional couplers. Work supported by the US DOE under DE-FC02-04ER54698.

  12. High Fidelity Simulations of Electromagnetic Propagation and RF Communication Systems

    Science.gov (United States)

    2017-05-01

    planning or platform performance assessment within a virtual scene. This report presents the results of two test cases—within a virtual rendering of...of remotely controlled robotics in virtual environments, par- ticularly urban scenes. Dr. Goodin’s simulation platform is the Virtual Au- tonomous...for mission planning or platform performance assessment within a virtual scene. This report presents the results of two test cases—within a virtual

  13. System integration of RF based negative ion experimental facility at IPR

    Energy Technology Data Exchange (ETDEWEB)

    Bansal, G; Bandyopadhyay, M; Singh, M J; Gahlaut, A; Soni, J; Pandya, K; Parmar, K G; Sonara, J; Chakraborty, A, E-mail: bansal@ipr.res.i [Institute for Plasma Research, Bhat, Gandhinagar (Gujarat) 382 428 (India)

    2010-02-01

    The setting up of RF based negative ion experimental facility shall witness the beginning of experiments on the negative ion source fusion applications in India. A 1 MHz RF generator shall launch 100 kW RF power into a single driver on the plasma source to produce a plasma of density {approx}5 x 10{sup 12} cm{sup -3}. The source can deliver a negative ion beam of {approx}10 A with a current density of {approx}30 mA/cm{sup 2} and accelerated to 35 kV through an electrostatic ion accelerator. The experimental system is similar to a RF based negative ion source, BATMAN, presently operating at IPP. The subsystems for source operation are designed and procured principally from indigenous resources, keeping the IPP configuration as a base line. The operation of negative ion source is supported by many subsystems e.g. vacuum pumping system with gate valves, cooling water system, gas feed system, cesium delivery system, RF generator, high voltage power supplies, data acquisition and control system, and different diagnostics. The first experiments of negative ion source are expected to start at IPR from the middle of 2009.

  14. Digital base-band rf control system for the superconducting Darmstadt electron linear accelerator

    Directory of Open Access Journals (Sweden)

    M. Konrad

    2012-05-01

    Full Text Available The accelerating field in superconducting cavities has to be stabilized in amplitude and phase by a radio-frequency (rf control system. Because of their high loaded quality factor superconducting cavities are very susceptible for microphonics. To meet the increased requirements with respect to accuracy, availability, and diagnostics, the previous analog rf control system of the superconducting Darmstadt electron linear accelerator S-DALINAC has been replaced by a digital rf control system. The new hardware consists of two components: An rf module that converts the signal from the cavity down to the base-band and a field-programmable gate array board including a soft CPU that carries out the signal processing steps of the control algorithm. Different algorithms are used for normal-conducting and superconducting cavities. To improve the availability of the control system, techniques for automatic firmware and software deployment have been implemented. Extensive diagnostic features provide the operator with additional information. The architecture of the rf control system as well as the functionality of its components will be presented along with measurements that characterize the performance of the system, yielding, e.g., an amplitude stabilization down to (ΔA/A_{rms}=7×10^{-5} and a phase stabilization of (Δϕ_{rms}=0.8° for superconducting cavities.

  15. Plasma properties of RF magnetron sputtering system using Zn target

    Energy Technology Data Exchange (ETDEWEB)

    Nafarizal, N.; Andreas Albert, A. R.; Sharifah Amirah, A. S.; Salwa, O.; Riyaz Ahmad, M. A. [Microelectronic and Nanotechnology - Shamsuddin Research Centre (MiNT-SRC), Faculty of Electrical and Electronic Engineering, Universiti Tun Hussein Onn Malaysia 86400 Parit Raja, Batu Pahat, Johor (Malaysia)

    2012-06-29

    In the present work, we investigate the fundamental properties of magnetron sputtering plasma using Zn target and its deposited Zn thin film. The magnetron sputtering plasma was produced using radio frequency (RF) power supply and Argon (Ar) as ambient gas. A Langmuir probe was used to collect the current from the plasma and from the current intensity, we calculate the electron density and electron temperature. The properties of Zn sputtering plasma at various discharge conditions were studied. At the RF power ranging from 20 to 100 W and gas pressure 5 mTorr, we found that the electron temperature was almost unchanged between 2-2.5 eV. On the other hand, the electron temperature increased drastically from 6 Multiplication-Sign 10{sup 9} to 1 Multiplication-Sign 10{sup 10}cm{sup -3} when the discharge gas pressure increased from 5 to 10 mTorr. The electron microscope images show that the grain size of Zn thin film increase when the discharge power is increased. This may be due to the enhancement of plasma density and sputtered Zn density.

  16. Compact Superconducting Radio-frequency Accelerators and Innovative RF Systems

    Energy Technology Data Exchange (ETDEWEB)

    Kephart, Robert [Fermilab; Chattopadhyay, Swaapan [Northern Illinois U.; Milton, Stephen [Colorado State U.

    2015-04-10

    We will present several new technical and design breakthroughs that enable the creation of a new class of compact linear electron accelerators for industrial purposes. Use of Superconducting Radio-Frequency (SRF) cavities allow accelerators less than 1.5 M in length to create electron beams beyond 10 MeV and with average beam powers measured in 10’s of KW. These machines can have the capability to vary the output energy dynamically to produce brehmstrahlung x-rays of varying spectral coverage for applications such as rapid scanning of moving cargo for security purposes. Such compact accelerators will also be cost effective for many existing and new industrial applications. Examples include radiation crosslinking of plastics and rubbers, creation of pure materials with surface properties radically altered from the bulk, modification of bulk or surface optical properties of materials, sterilization of medical instruments animal solid or liquid waste, and destruction of organic compounds in industrial waste water effluents. Small enough to be located on a mobile platform, such accelerators will enable new remediation methods for chemical and biological spills and/or in-situ crosslinking of materials. We will describe one current design under development at Fermilab including plans for prototype and value-engineering to reduce costs. We will also describe development of new nano-structured field-emitter arrays as sources of electrons, new methods for fabricating and cooling superconducting RF cavities, and a new novel RF power source based on magnetrons with full phase and amplitude control.

  17. Quantum Communication Systems

    Science.gov (United States)

    2008-03-15

    Standard Form 298 (Rev. 8/98) Prescribed by ANSI Std. Z39-18 Publications: 1) W. Wasilewski and...K. Banaszek, Protecting an optical qubit against photon loss, Phys. Rev. A 75, 042316 (2007) 2) K. Banaszek and W. Wasilewski , Linear-optics...manipulations of photon-loss codes, Proceedings of NATO Advanced Research Workshop "Quantum Communication and Security" 3) W. Wasilewski , P. Kolenderski

  18. High-power multimode X-band rf pulse compression system for future linear colliders

    Directory of Open Access Journals (Sweden)

    Sami G. Tantawi

    2005-04-01

    Full Text Available We present a multimode X-band rf pulse compression system suitable for a TeV-scale electron-positron linear collider such as the Next Linear Collider (NLC. The NLC main linac operating frequency is 11.424 GHz. A single NLC rf unit is required to produce 400 ns pulses with 475 MW of peak power. Each rf unit should power approximately 5 m of accelerator structures. The rf unit design consists of two 75 MW klystrons and a dual-moded resonant-delay-line pulse compression system that produces a flat output pulse. The pulse compression system components are all overmoded, and most components are designed to operate with two modes. This approach allows high-power-handling capability while maintaining a compact, inexpensive system. We detail the design of this system and present experimental cold test results. We describe the design and performance of various components. The high-power testing of the system is verified using four 50 MW solenoid-focused klystrons run off a common 400 kV solid-state modulator. The system has produced 400 ns rf pulses of greater than 500 MW. We present the layout of our system, which includes a dual-moded transmission waveguide system and a dual-moded resonant line (SLED-II pulse compression system. We also present data on the processing and operation of this system, which has set high-power records in coherent and phase controlled pulsed rf.

  19. Reaction of the immune system to low-level RF/MW exposures.

    Science.gov (United States)

    Szmigielski, Stanislaw

    2013-06-01

    Radiofrequency (RF) and microwave (MW) radiation have been used in the modern world for many years. The rapidly increasing use of cellular phones in recent years has seen increased interest in relation to the possible health effects of exposure to RF/MW radiation. In 2011 a group of international experts organized by the IARC (International Agency for Research on Cancer in Lyon) concluded that RF/MW radiations should be listed as a possible carcinogen (group 2B) for humans. The incomplete knowledge of RF/MW-related cancer risks has initiated searches for biological indicators sensitive enough to measure the "weak biological influence" of RF/MWs. One of the main candidates is the immune system, which is able to react in a measurable way to discrete environmental stimuli. In this review, the impacts of weak RF/MW fields, including cell phone radiation, on various immune functions, both in vitro and in vivo, are discussed. The bulk of available evidence clearly indicates that various shifts in the number and/or activity of immunocompetent cells are possible, however the results are inconsistent. For example, a number of lymphocyte functions have been found to be enhanced and weakened within single experiments based on exposure to similar intensities of MW radiation. Certain premises exist which indicate that, in general, short-term exposure to weak MW radiation may temporarily stimulate certain humoral or cellular immune functions, while prolonged irradiation inhibits the same functions. Copyright © 2013. Published by Elsevier B.V.

  20. Reaction of the immune system to low-level RF/MW exposures

    Energy Technology Data Exchange (ETDEWEB)

    Szmigielski, Stanislaw, E-mail: szmigielski@wihe.waw.pl

    2013-06-01

    Radiofrequency (RF) and microwave (MW) radiation have been used in the modern world for many years. The rapidly increasing use of cellular phones in recent years has seen increased interest in relation to the possible health effects of exposure to RF/MW radiation. In 2011 a group of international experts organized by the IARC (International Agency for Research on Cancer in Lyon) concluded that RF/MW radiations should be listed as a possible carcinogen (group 2B) for humans. The incomplete knowledge of RF/MW-related cancer risks has initiated searches for biological indicators sensitive enough to measure the “weak biological influence” of RF/MWs. One of the main candidates is the immune system, which is able to react in a measurable way to discrete environmental stimuli. In this review, the impacts of weak RF/MW fields, including cell phone radiation, on various immune functions, both in vitro and in vivo, are discussed. The bulk of available evidence clearly indicates that various shifts in the number and/or activity of immunocompetent cells are possible, however the results are inconsistent. For example, a number of lymphocyte functions have been found to be enhanced and weakened within single experiments based on exposure to similar intensities of MW radiation. Certain premises exist which indicate that, in general, short-term exposure to weak MW radiation may temporarily stimulate certain humoral or cellular immune functions, while prolonged irradiation inhibits the same functions.

  1. Emittance growth, debunching and integrated luminosity in the LHC with a higher harmonic RF system

    CERN Document Server

    Mertens, T

    2011-01-01

    Beam dynamics with a double RF system has been considered in several references. Recently the idea of adding a secondary RF system has resurfaced due to heating effects in the beam screens of the LHC that are caused by the high particle densities in the bunch centres with a Gaussian longitudinal profile. It is well known that one can change the longitudinal bunch profile from a Gaussian profile like the pink curve in Figure 1 into a plateau shape like the blue curve in Figure 1 reducing the particle density in the bunch centres. Here we study the evolution of a bunch with such a longitudinal plateau like shape under the influence of IBS in a double RF system and how adding a secondary RF system in the LHC influences debunching losses and integrated luminosity. The simulations presented here are done with the particle tracking code that was used to study IBS effects in the 2010 ion fills. The results of our simulations indicate that installing a secondary higher harmonic RF system in the LHC would significantl...

  2. An Overview of the MaRIE X-FEL and Electron Radiography LINAC RF Systems

    Energy Technology Data Exchange (ETDEWEB)

    Bradley, Joseph Thomas III [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Rees, Daniel Earl [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Scheinker, Alexander [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Sheffield, Richard L. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2015-05-04

    The purpose of the Matter-Radiation Interactions in Extremes (MaRIE) facility at Los Alamos National Laboratory is to investigate the performance limits of materials in extreme environments. The MaRIE facility will utilize a 12 GeV linac to drive an X-ray Free-Electron Laser (FEL). Most of the same linac will also be used to perform electron radiography. The main linac is driven by two shorter linacs; one short linac optimized for X-FEL pulses and one for electron radiography. The RF systems have historically been the one of the largest single component costs of a linac. We will describe the details of the different types of RF systems required by each part of the linacs. Starting with the High Power RF system, we will present our methodology for the choice of RF system peak power and pulselength with respect to klystron parameters, modulator parameters, performance requirements and relative costs. We will also present an overview of the Low Level RF systems that are proposed for MaRIE and briefly describe their use with some proposed control schemes.

  3. Development of an Automatic Frequency Control (AFC) System for RF Electron Linear Accelerators

    Energy Technology Data Exchange (ETDEWEB)

    Cha, Sungsu; Kim, Yujong; Lee, Byeong-No; Joo, Youngwoo; Lee, Soo Min; Lee, Byung Cheol; Cha, Hyungki [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Park, Hyung Dal [Radiation Technology eXcellence, Daejeon (Korea, Republic of); Lee, Seung Hyun [Sungkyunkwan University, Suwon (Korea, Republic of)

    2015-10-15

    In this paper, the design, fabrication, and RF power test of the AFC system for the X-band linac are presented. The main function of the AFC system is automatically matching of the resonance frequency of the accelerating structure and the RF frequency of the magnetron. For the frequency tuning, a fine tuning of 10 kHz is possible by rotating the tuning shaft with a rotation of 0.72 degree per pulse. Therefore, the frequency deviation is about 0.01%, and almost full RF power (2.1 MW) transmission was obtained because the reflected power is minimized. The Radiation Equipment Research Division of the Korea Atomic Energy Research Institute has been developing and upgrading a medical/industrial X-band RF electron linear accelerators. The medical compact RF electron linear accelerator consists of an electron gun, an acceleration tube (accelerating structure), two solenoid magnets, two steering magnets, a magnetron, modulator, an automatic frequency control (AFC) system, and an X-ray generating target. The accelerating structure of the component is composed of oxygen-free high-conductivity copper (OFHC). Therefore, the volume of the structure, hence, its resonance frequency can easily be changeable if the ambient temperature and pressure are changed. If the RF frequency of the 9300 MHz magnetron and the resonance frequency of accelerating structure are not matched, performance of the structure can be degraded. An AFC system is automatically matched with the RF frequency of the magnetron and resonance frequency of the accelerating structure, which obtained a high output power and reliable accelerator operation.

  4. The DSP-Carrier Board Used by the LEIR Low-Level RF System User's Manual

    CERN Document Server

    Angoletta, M E

    2007-01-01

    A new digital technology to implement beam control systems was tested in the PS Booster in 2004 and 2005 and commissioned in LEIR in 2006. The technology is based upon RF custom hardware that heavily exploits Digital Signal Processors (DSPs) and Field Programmable Gate Arrays (FPGAs) processing power. This architecture is extremely flexible in that it relies on a DSP-carrier board hosting one DSP and carrying different daughtercards. The LEIR beam control system deploys three DSP-carrier boards, which inter-communicate and exchange data continuously for the implementation of the various beam control loops. This user's manual for the DSP-carrier board, release 1.0 (EDA-00990-V1), was written in 2004 and has been used by CERN and BNL developers since then. It describes the DSP-carrier board hardware, user settings and FPGA software; hints on the DSP code used with the board are also given. An additional VME board, called Rear Transition Module, is described because it acts as a DSP-carrier board extension.

  5. Stabilizing Effect of a Double-Harmonic RF System in the CERN PS

    CERN Document Server

    Bhat, C M; Damerau, H; Hancock, S; Mahner, E; Zimmermann, F

    2010-01-01

    Motivated by the discussions on scenarios for LHC upgrades, beam studies on the stability of flat bunches in a double-harmonic RF system have been conducted in the CERN Proton Synchrotron (PS). Injecting nearly nominal LHC beam intensity per cycle, 18 bunches are accelerated on harmonic h=21 to 26 GeV with the 10 MHz RF system. On the flat-top, all bunches are then transformed to flat bunches by adiabatically adding RF voltage at h=42 from a 20 MHz cavity in anti-phase to the h=21 system. The voltage ratio V(h42)/V(h21) of about 0.5 was set according to simulations. For the next 140 ms,longitudinal profiles show stable bunches in the double harmonic RF bucket until extraction. Without the second harmonic component, coupled-bunch oscillations are observed. The flatness of the bunches along the batch is analyzed as a measure of the relative phase error between the RF systems due to beam loading. Measurements of electron cloud effects induced by the beam are also discussed. The results of beam dynamics simulatio...

  6. Stabilizing effect of a double-harmonic RF system in the CERN PS

    CERN Document Server

    Bhat, C M; Damerau, H; Hancock, S; Mahner, E; Zimmermann, F

    2010-01-01

    Motivated by the discussions on scenarios for LHC upgrades, beam studies on the stability of flat bunches in a double-harmonic RF system have been conducted in the CERN Proton Synchrotron (PS). Injecting nearly nominal LHC beam intensity per cycle, 18 bunches are accelerated on harmonic h = 21 to 26GeV with the 10MHz RF system. On the flat-top, all bunches are then transformed to flat bunches by adiabatically adding RF voltage at h = 42 from a 20MHz cavity in anti-phase to the h = 21 system. The voltage ratio V (h42)/V (h21) of about 0.5 was set according to simulations. For the next 140 ms, longitudinal profiles show stable bunches in the double-harmonic RF bucket until extraction. Without the second harmonic component, coupled-bunch oscillations are observed. The flatness of the bunches along the batch is analyzed as a measure of the relative phase error between the RF systems due to beam loading. The results of beam dynamics simulations and their comparison with the measured data are presented.

  7. STABILIZING EFFECT OF A DOUBLE-HARMONIC RF SYSTEM IN THE CERN PS

    CERN Document Server

    Bhat, C M; Damerau, H; Hancock, S; Mahner, E; Zimmermann, F

    2009-01-01

    Motivated by the discussions on scenarios for LHC upgrades, beam studies on the stability of flat bunches in a double-harmonic RF system have been conducted in the CERN Proton Synchrotron (PS). Injecting nearly nominal LHC beam intensity per cycle, 18 bunches are accelerated on harmonic h = 21 to 26GeV with the 10MHz RF system. On the flat-top, all bunches are then transformed to flat bunches by adiabatically adding RF voltage at h = 42 from a 20MHz cavity in anti-phase to the h = 21 system. The voltage ratio V (h42)/V (h21) of about 0.5 was set according to simulations. For the next 140 ms, longitudinal profiles show stable bunches in the double-harmonic RF bucket until extraction. Without the second harmonic component, coupled-bunch oscillations are observed. The flatness of the bunches along the batch is analyzed as a measure of the relative phase error between the RF systems due to beam loading. The results of beamdynamics simulations and their comparison with the measured data are presented.

  8. A 166.6 MHz superconducting rf system for the HEPS storage ring

    Science.gov (United States)

    Zhang, P.; Hao, X.; Huang, T.; Li, Z.; Lin, H.; Meng, F.; Mi, Z.; Sun, Y.; Wang, G.; Wang, Q.; Zhang, X.

    2017-07-01

    A superconducting 166.6 MHz quarter-wave beta=1 cavity was recently proposed for the High Energy Photon Source (HEPS), a 6 GeV kilometer-scale light source. Four 166.6 MHz cavities will be used for main acceleration in the newly planned on-axis beam injection scheme realized by a double-frequency RF system. The fundamental frequency, 166.6 MHz, was dictated by the fast injection kicker technology and the preference of using 499.8 MHz SC RF cavity as the third harmonic. Each 166.6 MHz cavity will be operated at 4.2 K providing 1.2 MV accelerating voltage and 150 kW of power to the electron beam. The input coupler will use single-window coaxial type graded up to 200 kW CW power. Each cavity will be equipped with a 200 kW solid-state amplifier and digital low-level RF system. This paper describes the 166.6 MHz RF system with a focus on the design and optimization of the RF cavity and its ancillaries, the LLRF system and the status of the solid-state amplifiers.

  9. SNS Low-Level RF Control System Design and Performance

    CERN Document Server

    Ma, Hengjie; Crofford, Mark; Doolittle, Lawrence; Kasemir, Kay-Uwe; Piller, Maurice; Ratti, Alessandro

    2005-01-01

    A full digital Low-Level RF controller has been developed for SNS LINAC. Its design is a good example of a modern digital implementation of the classic control theory. The digital hardware for all the control and DSP functionalities, including the final vector modulation, is implemented on a single high-density FPGA. Two models for the digital hardware have been written in VHDL and Verilog respectively, based on a very low latency control algorithm, and both have been being used for supporting the testing and commissioning the LINAC to the date. During the commissioning, the flexibility and ability for precise controls that only digital design on a larger FPGA can offer has proved to be a necessity for meeting the great challenge of a high-power pulsed SCL.

  10. 49 CFR 193.2519 - Communication systems.

    Science.gov (United States)

    2010-10-01

    ... primary communication system that provides for verbal communications between all operating personnel at...) storage capacity must have an emergency communication system that provides for verbal communications... 49 Transportation 3 2010-10-01 2010-10-01 false Communication systems. 193.2519 Section 193.2519...

  11. Klystron 'efficiency loop' for the ALS storage ring RF system

    Energy Technology Data Exchange (ETDEWEB)

    Kwiatkowski, Slawomir; Julian, Jim; Baptiste, Kenneth

    2002-05-20

    The recent energy crisis in California has led us to investigate the high power RF systems at the Advanced Light Source (ALS) in order to decrease the energy consumption and power costs. We found the Storage Ring Klystron Power Amplifier system operating as designed but with significant power waste. A simple proportional-integrator (PI) analog loop, which controls the klystron collector beam current, as a function of the output RF power, has been designed and installed. The design considerations, besides efficiency improvement, were to interface to the existing system without major expense. They were to also avoid the klystron cathode power supply filter's resonance in the loop's dynamics, and prevent a conflict with the existing Cavity RF Amplitude Loop dynamics. This efficiency loop will allow us to save up to 700 MW-hours of electrical energy per year and increase the lifetime of the klystron.

  12. Aspects of operation of the Fermilab Booster RF System at very high intensity

    Energy Technology Data Exchange (ETDEWEB)

    Griffin, J.E.

    1996-04-01

    The purpose of this note is to examine the likelihood and problems associated with operation of the Fermilab Booster rf systems as it presently exists, or with only minor modifications, at beam intensity approaching 5x10{sup 13} protons per pulse. Beam loading of the rf system at such an intensity will be one order of magnitude larger than at the present operation level. It is assumed that the injection energy will be raised to 1 GeV with no major increase in the injected energy spread (longitudinal emittance). The beam will be bunched by adiabatic capture as is presently done although it may be necessary to remove one or two bunches prior to acceleration to allow clean extraction at 8 GeV. At very high intensity the charge in each bunch will interact with the vacuum chamber impedance (and with itself) in such a way as to reduce in some cases the bucket area generated by the rf voltage. Because this decrement must be made up by changes in the rf ring voltage if the required bucket area is to be maintained, these effects must be taken into consideration in any analysis of the capability of the rf system to accelerate very large intensity.

  13. Communicating embedded systems networks applications

    CERN Document Server

    Krief, Francine

    2013-01-01

    Embedded systems become more and more complex and require having some knowledge in various disciplines such as electronics, data processing, telecommunications and networks. Without detailing all the aspects related to the design of embedded systems, this book, which was written by specialists in electronics, data processing and telecommunications and networks, gives an interesting point of view of communication techniques and problems in embedded systems. This choice is easily justified by the fact that embedded systems are today massively communicating and that telecommunications and network

  14. Advanced satellite communication system

    Science.gov (United States)

    Staples, Edward J.; Lie, Sen

    1992-01-01

    The objective of this research program was to develop an innovative advanced satellite receiver/demodulator utilizing surface acoustic wave (SAW) chirp transform processor and coherent BPSK demodulation. The algorithm of this SAW chirp Fourier transformer is of the Convolve - Multiply - Convolve (CMC) type, utilizing off-the-shelf reflective array compressor (RAC) chirp filters. This satellite receiver, if fully developed, was intended to be used as an on-board multichannel communications repeater. The Advanced Communications Receiver consists of four units: (1) CMC processor, (2) single sideband modulator, (3) demodulator, and (4) chirp waveform generator and individual channel processors. The input signal is composed of multiple user transmission frequencies operating independently from remotely located ground terminals. This signal is Fourier transformed by the CMC Processor into a unique time slot for each user frequency. The CMC processor is driven by a waveform generator through a single sideband (SSB) modulator. The output of the coherent demodulator is composed of positive and negative pulses, which are the envelopes of the chirp transform processor output. These pulses correspond to the data symbols. Following the demodulator, a logic circuit reconstructs the pulses into data, which are subsequently differentially decoded to form the transmitted data. The coherent demodulation and detection of BPSK signals derived from a CMC chirp transform processor were experimentally demonstrated and bit error rate (BER) testing was performed. To assess the feasibility of such advanced receiver, the results were compared with the theoretical analysis and plotted for an average BER as a function of signal-to-noise ratio. Another goal of this SBIR program was the development of a commercial product. The commercial product developed was an arbitrary waveform generator. The successful sales have begun with the delivery of the first arbitrary waveform generator.

  15. Compressive Sensing in Communication Systems

    DEFF Research Database (Denmark)

    Fyhn, Karsten

    2013-01-01

    Wireless communication is omnipresent today, but this development has led to frequency spectrum becoming a limited resource. Furthermore, wireless devices become more and more energy-limited, due to the demand for continual wireless communication of higher and higher amounts of information....... The need for cheaper, smarter and more energy efficient wireless devices is greater now than ever. This thesis addresses this problem and concerns the application of the recently developed sampling theory of compressive sensing in communication systems. Compressive sensing is the merging of signal...... acquisition and compression. It allows for sampling a signal with a rate below the bound dictated by the celebrated Shannon-Nyquist sampling theorem. In some communication systems this necessary minimum sample rate, dictated by the Shannon-Nyquist sampling theorem, is so high it is at the limit of what...

  16. EMI protection for communication systems

    CERN Document Server

    Malaric, Kresimir

    2009-01-01

    This practical reference provides a thorough understanding of how to protect communication systems from intentional and unintentional electromagnetic interference. You learn how to overcome critical problems in both digital and analog communications. This unique resource shows you how to shield equipment from electrical and magnetic fields, design TEM and GTEM-Cell, build capacitive coupling clamps for susceptibility tests, protect electronic equipment with filters, and calculate the measurement uncertainty. You find numerous, well-illustrated examples that make challenging electromagnetics is

  17. High Precision Temperature Control and Analysis of RF Deionized Cooling Water System

    CERN Document Server

    Tsai, Zong-Da; Chen June Rong; Liu, Chen-Yao

    2005-01-01

    Previously, the Taiwan Light Source (TLS) has proven the good beam quality mainly depends on the utility system stability. A serial of efforts were devoted to these studies. Further, a high precision temperature control of the RF deionized cooling water system will be achieved to meet the more critical stability requirement. The paper investigates the mixing mechanism through thermal and flow analysis and verifies the practical influences. A flow mixing mechanism and control philosophy is studied and processed to optimize temperature variation which has been reduced from ±0.1? to ±0.01?. Also, the improvement of correlation between RF performance and water cooling stability will be presented.

  18. Capture, acceleration and bunching rf systems for the MEIC booster and storage rings

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Shaoheng [Jefferson Lab, Newport News, VA; Guo, Jiquan [Jefferson Lab, Newport News, VA; Lin, Fanglei [Jefferson Lab, Newport News, VA; Morozov, Vasiliy [Jefferson Lab, Newport News, VA; Rimmer, Robert A. [Jefferson Lab, Newport News, VA; Wang, Haipeng [Jefferson Lab, Newport News, VA; Zhang, Yuhong [Jefferson Lab, Newport News, VA

    2015-09-01

    The Medium-energy Electron Ion Collider (MEIC), proposed by Jefferson Lab, consists of a series of accelerators. The electron collider ring accepts electrons from CEBAF at energies from 3 to 12 GeV. Protons and ions are delivered to a booster and captured in a long bunch before being ramped and transferred to the ion collider ring. The ion collider ring accelerates a small number of long ion bunches to colliding energy before they are re-bunched into a high frequency train of very short bunches for colliding. Two sets of low frequency RF systems are needed for the long ion bunch energy ramping in the booster and ion collider ring. Another two sets of high frequency RF cavities are needed for re-bunching in the ion collider ring and compensating synchrotron radiation energy loss in the electron collider ring. The requirements from energy ramping, ion beam bunching, electron beam energy compensation, collective effects, beam loading and feedback capability, RF power capability, etc. are presented. The preliminary designs of these RF systems are presented. Concepts for the baseline cavity and RF station configurations are described, as well as some options that may allow more flexible injection and acceleration schemes.

  19. Mobile Communication Systems and Security

    CERN Document Server

    Rhee, Man Young

    2009-01-01

    Mobile Communication Systems and Security arms readers with a thorough understanding of all major cellular air-interface technologies and their security layer techniques. Rhee covers the technological development of wireless mobile communications in compliance with each iterative generation up to 3G systems and beyond, with an emphasis on wireless security aspects. By progressing in a systematic manner, presenting the theory and practice of wireless mobile technologies along with various security problems, readers will gain an intimate sense of how mobile systems operate and how to address com

  20. Fiber-optic communication systems

    CERN Document Server

    Agrawal, Govind P

    2010-01-01

    This book provides a comprehensive account of fiber-optic communication systems. The 3rd edition of this book is used worldwide as a textbook in many universities. This 4th edition incorporates recent advances that have occurred, in particular two new chapters. One deals with the advanced modulation formats (such as DPSK, QPSK, and QAM) that are increasingly being used for improving spectral efficiency of WDM lightwave systems. The second chapter focuses on new techniques such as all-optical regeneration that are under development and likely to be used in future communication systems. All othe

  1. Recycler barrier RF buckets

    Energy Technology Data Exchange (ETDEWEB)

    Bhat, C.M.; /Fermilab

    2011-03-01

    The Recycler Ring at Fermilab uses a barrier rf systems for all of its rf manipulations. In this paper, I will give an overview of historical perspective on barrier rf system, the longitudinal beam dynamics issues, aspects of rf linearization to produce long flat bunches and methods used for emittance measurements of the beam in the RR barrier rf buckets. Current rf manipulation schemes used for antiproton beam stacking and longitudinal momentum mining of the RR beam for the Tevatron collider operation are explained along with their importance in spectacular success of the Tevatron luminosity performance.

  2. A Model of Internal Communication in Adaptive Communication Systems.

    Science.gov (United States)

    Williams, M. Lee

    A study identified and categorized different types of internal communication systems and developed an applied model of internal communication in adaptive organizational systems. Twenty-one large organizations were selected for their varied missions and diverse approaches to managing internal communication. Individual face-to-face or telephone…

  3. Design of Wireless Temperature Measuring System Based on the nRF24l01

    Directory of Open Access Journals (Sweden)

    Song Liu

    2016-02-01

    Full Text Available Wireless data transmission system which composed of wireless data transmission device nRF24L01, temperature sensor [DS18B20,] and STC89C52. The system can collect and transmit temperature information and display it on LED, when the temperature excess the set value, the system will alarm by the buzzer. The hardware and software of the design are explained in detail. Finally, the application of this system in wireless temperature collection system is discussed.

  4. Low level RF systems for synchrotrons part II: High Intensity. Compensation of the beam induced effects

    CERN Document Server

    Baudrenghien, P

    2005-01-01

    The high intensity regime is reached when the voltage induced by the beam in the RF cavities is of an amplitude comparable to the desired accelerating voltage. In steady state this beam loading can be compensated by providing extra RF power. Transient beam loading occurs at injection or in the presence of a beam intensity that is not uniform around the ring. The transients are periodic at the revolution frequency. Without correction transient beam loading can be very harmful: The stable phase and bucket area will not be equal for all bunches. Strong beam loading often goes in pair with longitudinal instabilities because the RF cavities are a large contributor to the total ring impedance. The low level systems that reduce the effect of the transient beam loading will also increase the threshold intensity of the longitudinal instability caused by the cavity impedance at the fundamental RF frequency. Four classic methods are presented here: Feedforward, RF feedback, long delay feedback and bunch by bunch feedbac...

  5. Sub-micron resolution rf cavity beam position monitor system at the SACLA XFEL facility

    Energy Technology Data Exchange (ETDEWEB)

    Maesaka, H., E-mail: maesaka@spring8.or.jp [RIKEN SPring-8 Center, Sayo, Hyogo (Japan); Ego, H. [RIKEN SPring-8 Center, Sayo, Hyogo (Japan); Inoue, S. [SPring-8 Service Co. Ltd., Tatsuno, Hyogo (Japan); Matsubara, S. [Japan Synchrotron Radiation Research Institute, Sayo, Hyogo (Japan); Ohshima, T.; Shintake, T.; Otake, Y. [RIKEN SPring-8 Center, Sayo, Hyogo (Japan)

    2012-12-22

    We have developed and constructed a C-band (4.760 GHz) rf cavity beam position monitor (RF-BPM) system for the XFEL facility at SPring-8, SACLA. The demanded position resolution of the RF-BPM is less than 1{mu}m, because an electron beam and x-rays must be overlapped within 4{mu}m precision in the undulator section for sufficient FEL interaction between the electrons and x-rays. In total, 57 RF-BPMs, including IQ demodulators and high-speed waveform digitizers for signal processing, were produced and installed into SACLA. We evaluated the position resolutions of 20 RF-BPMs in the undulator section by using a 7 GeV electron beam having a 0.1 nC bunch charge. The position resolution was measured to be less than 0.6{mu}m, which was sufficient for the XFEL lasing in the wavelength region of 0.1 nm, or shorter.

  6. OFDM systems for wireless communications

    CERN Document Server

    Narasimhamurthy, Adarsh

    2010-01-01

    Orthogonal Frequency Division Multiplexing (OFDM) systems are widely used in the standards for digital audio/video broadcasting, WiFi and WiMax. Being a frequency-domain approach to communications, OFDM has important advantages in dealing with the frequency-selective nature of high data rate wireless communication channels. As the needs for operating with higher data rates become more pressing, OFDM systems have emerged as an effective physical-layer solution.This short monograph is intended as a tutorial which highlights the deleterious aspects of the wireless channel and presents why OFDM is

  7. Tuning an rf-SQUID flux qubit system's potential with magnetic flux bias

    Institute of Scientific and Technical Information of China (English)

    Hua Tao; Xu Wei-Wei; Shi Jian-Xin; An De-Yue; Sun Guo-Zhu; Yu Yang; Wu Pei-Heng

    2012-01-01

    At an extremely low temperature of 20 mK,we measured the loop current in a tunable rf superconducting quantum interference device (SQUID) with a dc-SQUID.By adjusting the magnetic flux applied to the rf-SQUID loop (φf) and the small dc-SQUID (φcjjf),respectively,the potential shape of the system can be fully controlled in situ.Variation in the transition step and overlap size in the switching current with a barrier flux bias are analyzed,from which we can obtain some relevant device parameters and build a model to explain the experimental phenomenon.

  8. Intelligent Low-level RF System by Non-destructive Beam Monitoring Device for Cyclotrons

    CERN Document Server

    Malafeh, M S Sharifi Asadi; Afarideh, H; Chai, J S

    2015-01-01

    The project of a10MeV PET cyclotron accelerator for medical diagnosis and treatment was started at Amirkabir University of Technology in 2012. The low-level RF system of cyclotron accelerator is designed to stabilize acceleration voltage and control the resonance frequency of the cavity. In this work Intelligent Low Level Radio Frequency Circuit or ILLRF suitable for Most of the AVF cyclotron accelerators was designed by the beam monitoring device and narrow band tunable band-pass filter. In this design, for the RF phase detection does not need to signal processing by microcontroller

  9. Time reversal communication system

    Science.gov (United States)

    Candy, James V.; Meyer, Alan W.

    2008-12-02

    A system of transmitting a signal through a channel medium comprises digitizing the signal, time-reversing the digitized signal, and transmitting the signal through the channel medium. The channel medium may be air, earth, water, tissue, metal, and/or non-metal.

  10. RF photonics technology for phased array antenna applications

    NARCIS (Netherlands)

    Meijerink, A.; Roeloffzen, C.G.H.; Marpaung, D.A.I.; Zhuang, L.; Etten, van W.C.; Leinse, A.; Hoekman, M.; Heideman, R.G.

    2008-01-01

    One of the key research topics of the Telecommunication Engineering (TE) Group at the University of Twente (UT) is RF Photonics. The aim of this field is to develop schemes that utilize the advantages of optical technology for performing RF functions in wireless communication systems. Examples of su

  11. Online impedance matching system for ICRH-RF experiments on SST-1 tokamak

    Energy Technology Data Exchange (ETDEWEB)

    Joshi, R.; Singh, M.; Jadav, H.M.; Mishra, K.; Singh, Raj; Kulkarni, S.V.; Bora, D.

    2015-11-15

    High-power radio frequency (RF) heating system in the frequency range of ion cyclotron range of frequencies (ICRF) on tokamak needs a mechanism for matching impedance seen by the antenna in presence of plasma to the generator output impedance for maximum transfer of RF power to the plasma with minimum reflections to avoid damage to the generator. The impedance of the antenna is strongly dependent on edge plasma parameters and the impedance sometimes changes as fast as 10{sup −4} s, while the RF generators used can deliver full power only into constant load impedance. Hence, the matching system with dynamic response in between generator and antenna is very much essential for high power ICRF experiments when the plasma is of longer duration with variable load impedance. For ICRF system on SST-1 tokamak, two automatic matching systems are employed each for one transmission line, which consists of motorized stub tuners and phase shifters to match the antenna impedance in the time scale of 120 ms. As a part of initial testing, online impedance matching system is tested with individual transmission lines and then both the lines are matched simultaneously on a variable dummy load which simulates the plasma load. In order to deliver power to both the lines from a single RF generator, hybrid coupler is used which also protects RF generator from reflections up to certain extent. However for hybrid coupler has to work properly and both the lines should see same load impedance. The automatic matching system is installed on tokamak state super-conducting tokamak (SST-1) and is tested up to 140 kW power in the vacuum vessel of the tokamak. Here we present the details of the online matching system and its testing results. The significant result is that we could match the variable load impedance with the generator impedance within 120 ms by suitably adjusting the step counts of the motor controller.

  12. Atmospheric Optical Communication Systems.

    Science.gov (United States)

    1981-02-01

    Tnteral system noise due to dark current id is Oven by . 1d = 2qGrB"" (2-9) Dark current is due to detecor biasing in some instances, and in somue...8217 without extansive pro- gr-=:ing exer’ence. Although. the znodel is designed to be Lteracdve, slight mod-.- i~cadons winl ezw :&31 r~ing of the progrsm

  13. Selecting RF Amplifiers for Impedance Controlled LLRF Systems - Nonlinear Effects and System Implications

    Energy Technology Data Exchange (ETDEWEB)

    Fox, John D.; Mastorides, Themis; Rivetta, Claudio Hector; Van Winkle, Daniel; /SLAC

    2007-07-06

    Several high-current accelerators use feedback techniques in the accelerating RF systems to control the impedances seen by the circulating beam. These Direct and Comb Loop architectures put the high power klystron and LLRF signal processing components inside feedback loops, and the ultimate behavior of the systems depends on the individual sub-component properties. Imperfections and non-idealities in the signal processing leads to reduced effectiveness in the impedance control loops. In the PEP-II LLRF systems non-linear effects have been shown to reduce the achievable beam currents, increase low-mode longitudinal growth rates and reduce the margins and stability of the LLRF control loops. We present measurements of the driver amplifiers used in the PEP-II systems, and present measurement techniques needed to quantify the small-signal gain, linearity, transient response and image frequency generation of these amplifiers.

  14. Timing and low-level rf system for an x-ray laser

    Directory of Open Access Journals (Sweden)

    Yuji Otake

    2016-02-01

    Full Text Available An x-ray free-electron laser (XFEL, SACLA, designed to open up new science, was constructed for generating coherent x rays with a peak power of more than 10 GW and a very short pulse of below 30 fs. This feature demands a very highly short-term temporal stability of less than 50 fs to the acceleration rf field of SACLA. For this reason, we developed a timing and low-level rf (LLRF system for SACLA based on that of the SPring8 compact SASE source (SCSS test accelerator for verifying the feasibility of an XFEL. The performance of the system using the in-phase and quadrature rf manipulation method was improved from SCSS’s system. Since the facility length of SACLA is 700 m, which is 10 times longer than that of the SCSS test accelerator, a phase-stabilized optical-fiber system designed to transmit time standard rf signals with low loss was also developed and deployed. This optical-fiber system equips fiber optical-length feedback control in order to mitigate environmental effects, such as temperature and humidity changes. On the other hand, the demanded maximum rf temporal stability is less than 50 fs, which is almost 10 times smaller than that of the SCSS test accelerator. Hence, reducing electric noise and increasing the temperature stability around timing and LLRF instruments were necessary and realized with a very low-noise power supply and a hemathermal 19-inch enclosure. The short-term temporal performance of the timing LLRF system finally attained a temporal stability of less than 13.6 fs in rms measured by a beam arrival-time measurement. This stability greatly helps to achieve the stable x-ray lasing of SACLA for routine operation during user experiments.

  15. Chaotic systems in optical communications

    Science.gov (United States)

    Siuzdak, J.

    2016-09-01

    Communications application of chaotic oscillations of lasers with optoelectronic feedback was discussed. The possibility of eavesdropping of the transmission was analyzed. It was proved that if the rogue party precisely knows parameters of the chaotic system it may recreate the entire signals solely by observation of the optical signal power causing security breach.

  16. Design of a multivariable RF control system using gain-shaping in the frequency domain

    Science.gov (United States)

    Ziomek, C. D.; Jachim, S. P.; Natter, E. F.

    1991-05-01

    Due to the time-varying nature of the radio-frequency (RF) accelerator, RF field amplitude and phase parameters must be precisely controlled in order to confine and accelerate the charged particle beam. Typically, a feedback control system regulates the RF field, rejects noise and disturbances, and maintains operational stability over changes in the electrical structure of the accelerator. This paper describes a multivariable control system that compensates the electrical structure of the accelerator by using gain-shaping in the frequency domain. The amplitude and phase quantities have been resolved into in-phase and quadrature (I and Q) variables. These orthogonal variables have simple mathematical relationships, and can be analyzed using linear transfer function matrices. The transfer matrix theory has been applied to the design of the multivariable control system that regulates the RF field in-phase and quadrature components. Frequency-domain controllers compensate these two signals to provide desired frequency response characteristics. A control predistorter performs an inverse coupling function, so that the I and Q components are effectively decoupled by the accelerator. Furthermore, computer interface circuitry allows the adaptive optimization of the mathematical transfer functions of the compensators.

  17. RF-TSV DESIGN, MODELING AND APPLICATION FOR 3D MULTI-CORE COMPUTER SYSTEMS

    Institute of Scientific and Technical Information of China (English)

    Yu Le; Yang Haigang; Xie Yuanlu

    2012-01-01

    The state-of-the-art multi-core computer systems are based on Very Large Scale three Dimensional (3D) Integrated circuits (VLSI).In order to provide high-speed vertical data transmission in such 3D systems,efficient Through-Silicon Via (TSV) technology is critically important.In this paper,various Radio Frequency (RF) TSV designs and models are proposed.Specifically,the Cu-plug TSV with surrounding ground TSVs is used as the baseline structure.For further improvement,the dielectric coaxial and novel air-gap coaxial TSVs are introduced.Using the empirical parameters of these coaxial TSVs,the simulation results are obtained demonstrating that these coaxial RF-TSVs can provide two-order higher of cut-off frequencies than the Cu-plug TSVs.Based on these new RF-TSV technologies,we propose a novel 3D multi-core computer system as well as new architectures for manipulating the interfaces between RF and baseband circuit.Taking into consideration the scaling down of IC manufacture technologies,predictions for the performance of future generations of circuits are made.With simulation results indicating energy per bit and area per bit being reduced by 7% and 11% respectively,we can conclude that the proposed method is a worthwhile guideline for the design of future multi-core computer ICs.

  18. Design of the New Wideband RF System for the CERN PS Booster

    CERN Document Server

    Paoluzzi, Mauro; Angoletta, Maria Elena; Arnaudon, Luca; Energico, Salvatore; Findlay, Alan; Haase, Matthias; Jaussi, Michael; Jones, Anthony; Landré, David; Molendijk, John; Quartullo, Danilo; Shaposhnikova, Elena

    2016-01-01

    For the renovation and upgrade of the CERN PS Booster (PSB) RF systems a development project was launched in 2012. The design, based on a new approach, aimed at replacing the existing tuned, narrowband RF systems with wideband, modular, solid-state driven units. A wide range of issues had to be addressed spanning from RF power production, radiation hardness of solid-state devices, active cancellation of beam-induced voltages, dedicated low-level electronics allowing multi-harmonic operation and beam stability. Following a three-year prototyping and testing campaign and two international reviews, the project endorsement came at the end of year 2015. It foresees the complete removal of present h1, h2 and h10 systems and the deployment of a new one covering all the frequency ranges from 1 MHz to 18 MHz. The four PSB rings will be equipped with 144 identical acceleration cells providing 24 kV total RF voltage per ring. This paper describes the design concepts, the retained solutions, the expected performances and...

  19. ZnO on nickel RF micromechanical resonators for monolithic wireless communication applications

    Science.gov (United States)

    Wei, Mian; Avila, Adrian; Rivera, Ivan; Baghelani, Masoud; Wang, Jing

    2017-05-01

    On-chip integrability of high-Q RF passives alongside CMOS transistors is crucial for the implementation of monolithic radio transceivers. One of the most significant bottlenecks in back-end-of-line (BEoL) integration of MEMS devices on CMOS processed wafers is their relatively low thermal budget, which is less than that required for typical MEMS material deposition processes. This paper investigates electroplated nickel as a structural material for piezoelectrically-transduced resonators to demonstrate ZnO-on-nickel resonators with a CMOS-compatible low temperature process for the first time. Aside from the obvious manufacturing cost benefit, electroplated nickel is a reasonable substitute for polycrystalline or single crystal silicon and thin-film microcrystalline diamond device layers, while realizing decent acoustic velocity and moderate Q. Electroplated nickel has been already adopted by MEMSCAP, a multi-user MEMS process foundry, in its MetalMUMPs process. Furthermore, it is observed that a localized annealing process through Joule heating can be exploited to significantly improve the effective mechanical quality factor for the ZnO-on-nickel resonators, which is still lower than the reported AlN resonators. This work demonstrates ZnO-on-nickel piezoelectrically-actuated MEMS resonators and resonator arrays by using an IC compatible low temperature process. There is room for performance improvement by lowering the acoustic energy losses in the ZnO and nickel layers.

  20. Global services systems - Space communication

    Science.gov (United States)

    Shepphird, F. H.; Wolbers, H. L.

    1979-01-01

    The requirements projected to the year 2000 for space-based global service systems, including both personal communications and innovative services, are developed based on historic trends and anticipated worldwide demographic and economic growth patterns. The growing demands appear to be best satisfied by developing larger, more sophisticated space systems in order to reduce the size, complexity, and expense of ground terminals. The availability of low-cost ground terminals will, in turn, further stimulate the generation of new services and new customers.

  1. Studies of single bunch instability in a double RF harmonic system of the SPS at 26 GeV/c

    CERN Document Server

    Argyropoulos, T; Bohl, T; Damerau, H; Linnecar, T; Papotti, G; Shaposhnikova, E; Tückmantel, J; CERN. Geneva. BE Department

    2010-01-01

    This note presents the analysis of the measurements that were performed on 14/07/2009 and 11/08/2009, in the context of studying the single bunch instabilities at the Flat Bottom (FB, 26 GeV/c) of the SPS cycle for a single and double harmonic RF system. A higher harmonic RF system, like the 4th harmonic in the SPS, because of the increased synchrotron frequency spread that it causes, is one of the known techniques for beam stabilization. The aim of this Machine Development (MD) study was to explore the behavior of the bunch in a single and double RF system for different phase shifts between the two RF systems and for different intensities. In the course of the first MD, acquisitions of longitudinal bunch profiles were recorded while during the second MD peak detected beam signals were used to measure the growth rate of instabilities as a function of intensity and 800 MHz RF phase.

  2. High voltage power supplies for ITER RF heating and current drive systems

    Energy Technology Data Exchange (ETDEWEB)

    Gassmann, T., E-mail: thibault.gassmann@iter.org [ITER Organization, CS 90 046, 13067 St. Paul Lez Durance Cedex (France); Arambhadiya, B.; Beaumont, B. [ITER Organization, CS 90 046, 13067 St. Paul Lez Durance Cedex (France); Baruah, U.K. [Institute for Plasma Research, Near Indira Bridge, Bhat, Gandhinagar 382428 (India); Bonicelli, T. [Fusion For Energy, C/3 Josep Pla 2, Torres Diagonal Litoral-B3, E-08019 Barcelona (Spain); Darbos, C.; Purohit, D.; Decamps, H. [ITER Organization, CS 90 046, 13067 St. Paul Lez Durance Cedex (France); Albajar, F. [Fusion For Energy, C/3 Josep Pla 2, Torres Diagonal Litoral-B3, E-08019 Barcelona (Spain); Gandini, F.; Henderson, M.; Kazarian, F.; Lamalle, P.U.; Omori, T. [ITER Organization, CS 90 046, 13067 St. Paul Lez Durance Cedex (France); Parmar, D.; Patel, A. [Institute for Plasma Research, Near Indira Bridge, Bhat, Gandhinagar 382428 (India); Rathi, D. [ITER Organization, CS 90 046, 13067 St. Paul Lez Durance Cedex (France); Singh, N.P. [Institute for Plasma Research, Near Indira Bridge, Bhat, Gandhinagar 382428 (India)

    2011-10-15

    The RF heating and current drive (H and CD) systems to be installed for the ITER fusion machine are the electron cyclotron (EC), ion cyclotron (IC) and, although not in the first phase of the project, lower hybrid (LH). These systems require high voltage, high current power supplies (HVPS) in CW operation. These HVPS should deliver around 50 MW electrical power to each of the RF H and CD systems with stringent requirements in terms of accuracy, voltage ripple, response time, turn off time and fault energy. The PSM (Pulse Step Modulation) technology has demonstrated over the past 20 years its ability to fulfill these requirements in many industrial facilities and other fusion reactors and has therefore been chosen as reference design for the IC and EC HVPS systems. This paper describes the technical specifications, including interfaces, the resulting constraints on the design, the conceptual design proposed for ITER EC and IC HVPS systems and the current status.

  3. System considerations and RF front-end design for integration of satellite navigation and mobile standards

    Directory of Open Access Journals (Sweden)

    A. Miskiewicz

    2009-05-01

    Full Text Available The paper presents the challenges involved in a system design of a robust reconfigurable RF front-end for navigation and mobile standards. Receiver architecture is chosen from the point of view of inter-system interference and 130nm CMOS process characteristics. System concept covers the implementation of GPS, Galileo, UMTS, GSM and CDMA2000 using a Zero-IF architecture with reconfigurable analog and digital path. Feasibility studies of the system cover analysis of the wireless regulations and performance criteria, such as overall gain, noise figure (NF, and 1dB compression point (P1dB of the RF chain, phase noise requirements and VCO tuning range [1]. The presented chip was fabricated in 130 nm CMOS technology. System considerations are confirmed with the chip measurements of gain, noise figure, and linearity. Prospects for the future work are presented including technology shrink.

  4. A compact linear accelerator based on a scalable microelectromechanical-system RF-structure

    Science.gov (United States)

    Persaud, A.; Ji, Q.; Feinberg, E.; Seidl, P. A.; Waldron, W. L.; Schenkel, T.; Lal, A.; Vinayakumar, K. B.; Ardanuc, S.; Hammer, D. A.

    2017-06-01

    A new approach for a compact radio-frequency (RF) accelerator structure is presented. The new accelerator architecture is based on the Multiple Electrostatic Quadrupole Array Linear Accelerator (MEQALAC) structure that was first developed in the 1980s. The MEQALAC utilized RF resonators producing the accelerating fields and providing for higher beam currents through parallel beamlets focused using arrays of electrostatic quadrupoles (ESQs). While the early work obtained ESQs with lateral dimensions on the order of a few centimeters, using a printed circuit board (PCB), we reduce the characteristic dimension to the millimeter regime, while massively scaling up the potential number of parallel beamlets. Using Microelectromechanical systems scalable fabrication approaches, we are working on further reducing the characteristic dimension to the sub-millimeter regime. The technology is based on RF-acceleration components and ESQs implemented in the PCB or silicon wafers where each beamlet passes through beam apertures in the wafer. The complete accelerator is then assembled by stacking these wafers. This approach has the potential for fast and inexpensive batch fabrication of the components and flexibility in system design for application specific beam energies and currents. For prototyping the accelerator architecture, the components have been fabricated using the PCB. In this paper, we present proof of concept results of the principal components using the PCB: RF acceleration and ESQ focusing. Ongoing developments on implementing components in silicon and scaling of the accelerator technology to high currents and beam energies are discussed.

  5. In Depth Diagnostics for RF System Operation in the PEP-II B Factory

    CERN Document Server

    Van Winkle, Daniel; Teytelman, Dmitry

    2005-01-01

    The PEP-II RF systems incorporate numerous feedback loops in the low-level processing for impedance control and operating point regulation. The interaction of the multiple loops with the beam is complicated, and the systems incorporate online diagnostic tools to configure the feedback loops as well as to record fault files in the case of an RF abort. Rapid and consistent analysis of the RF-related beam aborts and other failures is critical to the reliable operation of the B-Factory, especially at the recently achieved high beam currents. Procedures and algorithms used to extract diagnostic information from time domain fault files are presented and illustrated via example interpretations of PEP-II fault file data. Example faults presented will highlight the subtle interpretation required to determine to root cause. Some such examples are: abort kicker firing asynchronously, klystron and cavity arcs, beam loss leading to longitudinal instability, tuner read back jumps and poorly configured low-level RF feedback...

  6. In Depth Diagnostics for RF System Operation in the PEP-II B Factory

    Energy Technology Data Exchange (ETDEWEB)

    Van Winkle, Daniel; Fox, John; Teytelman, Dmitry; /SLAC

    2005-05-27

    The PEP-II RF systems incorporate numerous feedback loops in the low-level processing for impedance control and operating point regulation. The interaction of the multiple loops with the beam is complicated, and the systems incorporate online diagnostic tools to configure the feedback loops as well as to record fault files in the case of an RF abort. Rapid and consistent analysis of the RF-related beam aborts and other failures is critical to the reliable operation of the B-Factory, especially at the recently achieved high beam currents. Procedures and algorithms used to extract diagnostic information from time domain fault files are presented and illustrated via example interpretations of PEP-II fault file data. Example faults presented will highlight the subtle interpretation required to determine the root cause. Some such examples are: abort kicker firing asynchronously, klystron and cavity arcs, beam loss leading to longitudinal instability, tuner read back jumps and poorly configured low-level RF feedback loop.

  7. Assessment of RF exposures from emerging wireless communication technologies in different environments.

    Science.gov (United States)

    Joseph, Wout; Verloock, Leen; Goeminne, Francis; Vermeeren, Gönter; Martens, Luc

    2012-02-01

    In situ electromagnetic (EM) radio frequency (RF) exposure to base stations of emerging wireless technologies is assessed at 311 locations, 68 indoor and 243 outdoor, spread over 35 areas in three European countries (Belgium, The Netherlands, and Sweden) by performing narrowband spectrum analyzer measurements. The locations are selected to characterize six different environmental categories (rural, residential, urban, suburban, office, and industrial). The maximal total field value was measured in a residential environment and equal to 3.9 V m(-1), mainly due to GSM900 signals. Exposure ratios for maximal electric field values, with respect to ICNIRP reference levels, range from 0.5% (WiMAX) to 9.3% (GSM900) for the 311 measurement locations. Exposure ratios for total field values vary from 3.1% for rural environments to 9.4% for residential environments. Exposures are lognormally distributed and are the lowest in rural environments and the highest in urban environments. Highest median exposures were obtained in urban environments (0.74 V m(-1)), followed by office (0.51 V m(-1)), industrial (0.49 V m(-1)), suburban (0.46 V m(-1)), residential (0.40 V m(-1)), and rural (0.09 V m(-1)) environments. The average contribution to the total electric field is more than 60% for GSM. Except for the rural environment, average contributions of UMTS-HSPA are more than 3%. Contributions of the emerging technologies LTE and WiMAX are on average less than 1%. The dominating outdoor source is GSM900 (95 percentile of 1.9 V m(-1)), indoor DECT dominates (95 percentile of 1.5 V m(-1)).

  8. RFID Transponders' RF Emissions in Aircraft Communication and Navigation Radio Bands

    Science.gov (United States)

    Nguyen, Truong X.; Ely, Jay J.; Koppen Sandra V.; Fersch, Mariatheresa S.

    2008-01-01

    Radiated emission data in aircraft communication and navigation bands are presented for several active radio frequency identification (RFID) tags. The individual tags are different in design, operation and transmitting frequencies. The process for measuring the tags emissions in a reverberation chamber is discussed. Measurement issues dealing with tag interrogation, low level measurement in the presence of strong transmissions, and tags low duty factors are discussed. The results show strong emissions, far exceeding aircraft emission limits and can be of potential interference risks.

  9. Technology development of RF MEMS switches on printed circuit boards

    Science.gov (United States)

    Chang, Hung-Pin

    Today, some engineers have shifted their focus on the micro-electro-mechanical system (MEMS) to pursue better technological advancements. Recent development in RF MEMS technologies have lead to superior switch characteristics, i.e., very low insertion loss, very low power requirements, and high isolation comparing to the conventional semiconductor devices. This success has promised the potential of MEMS to revolutionize RF and microwave system implementation for the next generation of communication applications. However, RF MEMS switches integrated monolithically with various RF functional components on the same substrate to create multifunctional and reconfigurable complete communication systems remains to be a challenge research topic due to the concerns of the high cost of packaging process and the high cost of RF matching requirements in module board implementation. Furthermore, the fabrication of most RF MEMS switches requires thickness control and surface planarization of wide metal lines prior to deposition of a metal membrane bridge, which poses a major challenge to manufacturability. To ease the fabrication of RF MEMS switches and to facilitate their integration with other RF components such as antennas, phase delay lines, tunable filters, it is imperative to develop a manufacturable RF MEMS switch technology on a common substrate housing all essential RF components. Development of a novel RF MEMS technology to build a RF MEMS switch and provide a system-level packaging on microwave laminated printed circuit boards (PCBs) are proposed in this dissertation. Two key processes, high-density inductively coupled plasma chemical vapor deposition (HDICP CVD) for low temperature dielectric deposition, and compressive molding planarization (COMP) for the temporary sacrificial polymer planarization have been developed for fabricating RF MEMS switches on PCBs. Several membrane-type capacitive switches have been fabricated showing excellent RF performance and dynamic

  10. Dynamic intensity control system with RF-knockout slow-extraction in the HIMAC synchrotron

    Science.gov (United States)

    Sato, Shinji; Furukawa, Takuji; Noda, Koji

    2007-05-01

    We have developed a dynamic beam intensity control system intended for use in three-dimensional pencil-beam scanning irradiation. In this system, which controls the spill structure and intensities of the beams extracted from the synchrotron, the amplitude of the RF-knockout is controlled using a 10 kHz response. Its amplitude modulation function is generated based on an analytical one-dimensional model of the RF-knockout slow-extraction. Using feedback control of the proportional and integral controls, this system allows us to control the beam current dynamically in response to the request, as was experimentally verified in the HIMAC synchrotron. In this paper, we describe the system for controlling the amplitude modulation through the inclusion of feedback, and we provide some experimental results.

  11. A 200 MHz SC-RF System for the HL-LHC

    CERN Document Server

    Calaga, Rama

    2016-01-01

    A quarter wave β=1 superconducting cavity at 200 MHz is proposed for the LHC as an alternative to the present 400 MHz RF system. The primary motivation of such a system would be to accelerate higher intensity and longer bunches with improved capture efficiency. Advantages related to minimizing electron cloud effects, intra-beam scattering, heating and the possibility of luminosity levelling with bunch length are described. Some considerations related to cavity optimization, beam loading and technological challenges are addressed.

  12. Initial experimental results of a machine learning-based temperature control system for an RF gun

    CERN Document Server

    Edelen, A L; Milton, S V; Chase, B E; Crawford, D J; Eddy, N; Edstrom, D; Harms, E R; Ruan, J; Santucci, J K; Stabile, P

    2015-01-01

    Colorado State University (CSU) and Fermi National Accelerator Laboratory (Fermilab) have been developing a control system to regulate the resonant frequency of an RF electron gun. As part of this effort, we present initial test results for a benchmark temperature controller that combines a machine learning-based model and a predictive control algorithm. This is part of an on-going effort to develop adaptive, machine learning-based tools specifically to address control challenges found in particle accelerator systems.

  13. Development of beam current control system in RF-knockout slow extraction

    Science.gov (United States)

    Mizushima, K.; Sato, S.; Shirai, T.; Furukawa, T.; Katagiri, K.; Takeshita, E.; Iwata, Y.; Himukai, T.; Noda, K.

    2011-12-01

    A raster scanning method has been developed for cancer therapy at NIRS-HIMAC. This method requires a high-accuracy beam current control and fast beam-on/off switching. We have developed a feedback control system of the beam current with the RF-knockout slow extraction method. The system has allowed a stable response to beam-on/off switching using a feedback control delay function with a beam-current ripple of 7%.

  14. Development of beam current control system in RF-knockout slow extraction

    Energy Technology Data Exchange (ETDEWEB)

    Mizushima, K., E-mail: mizshima@nirs.go.jp [Department of Accelerator and Medical Physics, National Institute of Radiological Sciences, 4-9-1 Anagawa, Inage-ku, Chiba 263-8555 (Japan); Graduate School of Science and Technology, Chiba University, Yayoi-cho, Inage-ku, Chiba 263-8522 (Japan); Sato, S.; Shirai, T.; Furukawa, T.; Katagiri, K.; Takeshita, E.; Iwata, Y.; Himukai, T.; Noda, K. [Department of Accelerator and Medical Physics, National Institute of Radiological Sciences, 4-9-1 Anagawa, Inage-ku, Chiba 263-8555 (Japan)

    2011-12-15

    A raster scanning method has been developed for cancer therapy at NIRS-HIMAC. This method requires a high-accuracy beam current control and fast beam-on/off switching. We have developed a feedback control system of the beam current with the RF-knockout slow extraction method. The system has allowed a stable response to beam-on/off switching using a feedback control delay function with a beam-current ripple of 7%.

  15. Joint compensation of multiple RF impairments in MIMO STBC systems

    KAUST Repository

    Qi, Jian

    2011-09-01

    In this paper, we propose a compensation method for the joint effect of high-power amplifier (HPA) nonlinearity, in-phase/quadrature-phase (I/Q) imbalance and crosstalk in multiple-input multiple-output (MIMO) orthogonal space-time block coding (OSTBC) systems. The performance of the MIMO OSTBC equipped with the proposed compensation mechanism is evaluated in terms of average symbol error probability and system capacity, in Rayleigh fading channels. Numerical results are provided and show the effects on performance of several system parameters, namely, the HPA parameters, image-leakage ratio, crosstalk, numbers of antennas, and phase-shift keying modulation order. © 2011 IEEE.

  16. Overview of communications programs

    Science.gov (United States)

    Depaula, Ramon P.

    1991-01-01

    The objective of the communications program is to advance critical areas of enabling and enhancing communication technologies that support commercial needs, science, and exploration missions for the 1990's and beyond. The technology program consists of research and technology development in the following areas: RF technology; digital technology; optical communications; mobile communications; and systems integration, test, and evaluation.

  17. Improved Controls for Fusion RF Systems. Final technical report

    Energy Technology Data Exchange (ETDEWEB)

    Casey, Jeffrey A. [Rockfield Research Inc., Las Vegas, NV (United States)

    2011-11-08

    We have addressed the specific requirements for the integrated systems controlling an array of klystrons used for Lower Hybrid Current Drive (LHCD). The immediate goal for our design was to modernize the transmitter protection system (TPS) for LHCD on the Alcator C-Mod tokamak at the MIT Plasma Science and Fusion Center (MIT-PSFC). Working with the Alcator C-Mod team, we have upgraded the design of these controls to retrofit for improvements in performance and safety, as well as to facilitate the upcoming expansion from 12 to 16 klystrons. The longer range goals to generalize the designs in such a way that they will be of benefit to other programs within the international fusion effort was met by designing a system which was flexible enough to address all the MIT system requirements, and modular enough to adapt to a large variety of other requirements with minimal reconfiguration.

  18. Short-range communication system

    Science.gov (United States)

    Alhorn, Dean C. (Inventor); Howard, David E. (Inventor); Smith, Dennis A. (Inventor)

    2012-01-01

    A short-range communication system includes an antenna, a transmitter, and a receiver. The antenna is an electrical conductor formed as a planar coil with rings thereof being uniformly spaced. The transmitter is spaced apart from the plane of the coil by a gap. An amplitude-modulated and asynchronous signal indicative of a data stream of known peak amplitude is transmitted into the gap. The receiver detects the coil's resonance and decodes same to recover the data stream.

  19. Precoding Design for Single-RF Massive MIMO Systems: A Large System Analysis

    KAUST Repository

    Sifaou, Houssem

    2016-08-26

    This work revisits a recently proposed precoding design for massive multiple-input multiple output (MIMO) systems that is based on the use of an instantaneous total power constraint. The main advantages of this technique lie in its suitability to the recently proposed single radio frequency (RF) MIMO transmitter coupled with a very-high power efficiency. Such features have been proven using simulations for uncorrelated channels. Based on tools from random matrix theory, we propose in this work to analyze the performance of this precoder for more involved channels accounting for spatial correlation. The obtained expressions are then optimized in order to maximize the signalto- interference-plus-noise ratio (SINR). Simulation results are provided in order to illustrate the performance of the optimized precoder in terms of peak-to-average power ratio (PAPR) and signal-to-interference-plus-noise ratio (SINR). © 2012 IEEE.

  20. Design of a new VHF RF power amplifier system for LANSCE

    Energy Technology Data Exchange (ETDEWEB)

    Lyles, John T M [Los Alamos National Laboratory

    2010-01-01

    A major upgrade is replacing much of the 40 year-old proton drift tube linac RF system with new components at the Los Alamos Neutron Science Center (LANSCE). When installed, the new system will reduce the total number of electron power tubes from twenty-four to eight in the RF powerplant. A new 200 MHz high power cavity amplifier has being developed at LANSCE. This 3.2 MW final power amplifier (FPA) uses a Thales TH628 Diacrode{reg_sign}, a state-of-the-art tetrode that eliminates the large anode modulator of the triode-based FPA that has been in use for four decades. Drive power for the FPA is provided by a new tetrode intermediate power amplifier (and a solid-state driver stage). The new system has sufficient duty-factor capability to allow LANSCE to return to 1 MW beam operation. Prototype RF power amplifiers have been designed, fabricated, and assembled, and are being tested. High voltage DC power became available through innovative re-engineering of an installed system. Details of the electrical and mechanical design of the FPA and ancillary systems are discussed.

  1. Design of an RF System for Electron Bernstein Wave Studies in MST

    Science.gov (United States)

    Kauffold, J. X.; Seltzman, A. H.; Anderson, J. K.; Nonn, P. D.; Forest, C. B.

    2010-11-01

    Motivated by the possibility of current profile control a 5.5GHz RF system for EBW is being developed. The central component is a standard radar Klystron with 1.2MW peak power and 4μs typical pulse length. Meaningful experiments require RF pulse lengths similar to the characteristic electron confinement times in MST necessitating the creation of a power supply providing 80kV at 40A for 10ms. A low inductance IGBT network switches power at 20kHz from an electrolytic capacitor bank into the primary of a three-phase resonant transformer system that is then rectified and filtered. The system uses three magnetically separate transformers with microcrystalline iron cores to provide suitable volt-seconds and low hysteresis losses. Each phase has a secondary with a large leakage inductance and a parallel capacitor providing a boost ratio greater than 60:1 with a physical turns ratio of 13.5:1. A microprocessor feedback control system varies the drive frequency around resonance to regulate the boost ratio and provide a stable output as the storage bank discharges. The completed system will deliver RF to the plasma boundary where coupling to the Bernstein mode and subsequent heating and current drive can occur.

  2. Reliability engineering in RF CMOS

    OpenAIRE

    2008-01-01

    In this thesis new developments are presented for reliability engineering in RF CMOS. Given the increase in use of CMOS technology in applications for mobile communication, also the reliability of CMOS for such applications becomes increasingly important. When applied in these applications, CMOS is typically referred to as RF CMOS, where RF stands for radio frequencies.

  3. Study on Airspace Covert Communication Algorithm of Covert Communication System

    Directory of Open Access Journals (Sweden)

    Yinpu Zhang

    2012-04-01

    Full Text Available Based on the security of information transmission through network in the information society, the paper puts forward covert communication technology which is more reliable than the prior encryption algorithm, analyzes channel covertness and information hiding of covert communication technology based on spread-spectrum communication technology, and establishes a covert communication system including image steganalysis, Arnold transformation and scrambling of carrier image, embedding of secret information, generation of encrypted image and recovering of carrier image by image-based covert communication technology. The simulation result shows: in order to ensure there is no serious degrading problem after embedding the secret information, the carrier image must have a large capacity; the larger the scrambling times is, the better the scrambling and encrypting effect is. Therefore, the airspace covert communication algorithm based on spread-spectrum communication technology well achieves safe transmission of information and has good application prospect.

  4. The development and application of a radiofrequency (RF) interstitial hyperthermia system to prostate cancer

    Energy Technology Data Exchange (ETDEWEB)

    Uchida, Nobue; Kawaguchi, Atsuya; Moriyama, Masahiro; Kitagaki, Hajime; Urakami, Shinji; Igawa, Mikio [Shimane Medical Univ., Izumo (Japan); Kato, Hirokazu [Okayama Univ. (Japan). School of Medicine; Kasai, Toshifumi [Kyoto Coll. of Medical Technology, Sonobe (Japan)

    2002-09-01

    To heat a greater volume less invasively and more effectively, we developed a multi-channel RF interstitial hyperthermia system compatible with the high-dose rate Iridium-192 remote after-loading system (Ir-192 RALS). The system is composed of eight channel RF signal generators, which can be controlled individually. Each RF generator can be connected to an internal electrode, which was originally an Ir-192 RALS applicator; and a shared rectangular external electrode made of aluminum. By means of experiments using an agar phantom and an animal liver, we evaluated the heating characteristics, safety, and feasibility of this system. Subsequently, we applied trans-perineal radiofrequency (RF) interstitial hyperthermia and Ir-192 RALS for localized prostate cancer (PC). Under trans-rectal ultrasound guidance, 18 stainless applicators for Ir-192 RALS were inserted into the prostatic gland and seminal vesicles in an optimized pattern. Eight applicators were used as internal electrodes and were electrically insulated along the length of subdermal fat tissue using a vinyl catheter. The temperature inside the prostate and rectum was monitored continuously. Hyperthermia was performed following the first and fourth Ir-192 RALS (total of 24 Gy/4 fractions). Total doses of 46 Gy were also delivered by linear accelerator. There were no complications, such as infection, bleeding, fat necrosis, or burns. Histological examination after the treatment revealed cancer cell death and necrosis. MRI and CT images showed a well-demarcated, low-intensity area at the center of the prostate reflecting the necrotic area. Trans-perineal hyperthermoradiotherapy is a feasible and effective therapeutic alternative for the treatment of patients with localized PC. In addition, our system is compatible with the Ir-192 RALS, allowing for less-invasive interstitial hyperthermoradiotherapy by eliminating the trauma of needle re-insertion. (author)

  5. Efficient RF energy harvesting by using a fractal structured rectenna system

    Science.gov (United States)

    Oh, Sechang; Ramasamy, Mouli; Varadan, Vijay K.

    2014-04-01

    A rectenna system delivers, collects, and converts RF energy into direct current to power the electronic devices or recharge batteries. It consists of an antenna for receiving RF power, an input filter for processing energy and impedance matching, a rectifier, an output filter, and a load resistor. However, the conventional rectenna systems have drawback in terms of power generation, as the single resonant frequency of an antenna can generate only low power compared to multiple resonant frequencies. A multi band rectenna system is an optimal solution to generate more power. This paper proposes the design of a novel rectenna system, which involves developing a multi band rectenna with a fractal structured antenna to facilitate an increase in energy harvesting from various sources like Wi-Fi, TV signals, mobile networks and other ambient sources, eliminating the limitation of a single band technique. The usage of fractal antennas effects certain prominent advantages in terms of size and multiple resonances. Even though, a fractal antenna incorporates multiple resonances, controlling the resonant frequencies is an important aspect to generate power from the various desired RF sources. Hence, this paper also describes the design parameters of the fractal antenna and the methods to control the multi band frequency.

  6. Centralized optical-frequency-comb-based RF carrier generator for DWDM fiber-wireless access systems

    DEFF Research Database (Denmark)

    Pang, Xiaodan; Beltran, Marta; Sanchez, Jose;

    2014-01-01

    In this paper, we report on a gigabit capacity fiber-wireless system that enables smooth integration between high-speed wireless networks and dense wavelength-division-multiplexing (DWDM) access networks. By employing a centralized optical frequency comb, both the wireline and the wireless services....... For demonstration, we transmit a 2.5 Gbit/s signal through the proposed system and successfully achieve a bit-error-rate (BER) performance well below the 7% overhead forward error correction limit of the BER of 2 × 10¿3 for both the wireline and the wireless signals in the 60 GHz band after 25 km single-mode fiber...... for each DWDM user can be simultaneously supported. Besides, each baseband channel can be transparently upconverted tomultiple radio-frequency (RF) bands for different wireless standards, which can be flexibly filtered at the end user to select the on-demand RF band, depending on the wireless applications...

  7. RF Fingerprinting Extraction and Identification of Wireless Communication Devices%无线通信设备的射频指纹提取与识别方法*

    Institute of Scientific and Technical Information of China (English)

    俞佳宝; 胡爱群; 朱长明; 彭林宁; 姜禹

    2016-01-01

    Wireless device identification via radio frequency (RF) fingerprinting extracted from communication signals is a physical layer approach for communication system security. In physical layer, RF fingerprinting is an inherent characteristic of wireless communication devices themselves, which can hardly be tampered. Just as people have unique fingerprints, different wireless devices exhibit different RF fingerprints which can be used for identification and authentication. This paper mainly provides a review of the research and development in RF fingerprinting extraction and identification in the past twenty years. According to the procedure of RF fingerprinting extraction and identification, we first analyze the generation mechanism of RF fingerprinting and the corresponding identification devices, which reflect the broad applications of the RF fingerprinting. Then, the identification signals are divided into transient signal and steady-state signal, and a method to detect and extract such signals are described. This paper further classifies the RF fingerprinting and summaries their five features, i.e., universality, uniqueness, short-time invariance, independence and robustness. This paper also summarizes the state of art on the procedure of transient and steady-state based techniques. It also describes how to evaluate the performance of RF fingerprinting identification systems. Finally, some potential research directions and challenges in this area are pointed out.%通过分析无线设备的通信信号来提取设备的射频指纹进行设备识别是一种保护通信系统安全的物理层方法。射频指纹是无线通信设备的物理层本质特征,很难被篡改。就像不同的人有不同的指纹,不同的无线设备也拥有不同的射频指纹,可用于无线设备的身份识别和接入认证。本文主要回顾了过去二十年国内外射频指纹技术的研究进展。根据射频指纹提取与识别的典型流程,首先分

  8. System-in-package RF design and applications

    CERN Document Server

    Gaynor, Michael P

    2006-01-01

    In the past few years, System in Package (SiP) design has fueled a revolution in the use of modules in wireless devices due its effectiveness in meeting the increasingly demanding requirements for reliability, shielding, performance, size, and cost. Here's the first comprehensive resource on SiP design techniques that offers designers state-of-the-art packaging know-how. Moreover, the book provides numerous examples that illustrate real-world capabilities, constraints, trade-offs, and options at every step.

  9. High power RF solid state power amplifier system

    Science.gov (United States)

    Sims, III, William Herbert (Inventor); Chavers, Donald Gregory (Inventor); Richeson, James J. (Inventor)

    2011-01-01

    A high power, high frequency, solid state power amplifier system includes a plurality of input multiple port splitters for receiving a high-frequency input and for dividing the input into a plurality of outputs and a plurality of solid state amplifier units. Each amplifier unit includes a plurality of amplifiers, and each amplifier is individually connected to one of the outputs of multiport splitters and produces a corresponding amplified output. A plurality of multiport combiners combine the amplified outputs of the amplifiers of each of the amplifier units to a combined output. Automatic level control protection circuitry protects the amplifiers and maintains a substantial constant amplifier power output.

  10. Phase Noise Influence in Optical OFDM Systems employing RF Pilot Tone for Phase Noise Cancellation

    OpenAIRE

    Jacobsen, Gunnar; Kazovsky, Leonid G.; Xu, TianHua; Popov, Sergei; Li, Jie; Zhang, Yimo; Friberg, Ari T.

    2016-01-01

    For coherent and direct-detection Orthogonal Frequency Division Multiplexed (OFDM) systems employing radio frequency (RF) pilot tone phase noise cancellation the influence of laser phase noise is evaluated. Novel analytical results for the common phase error and for the (modulation dependent) inter carrier interference are evaluated based upon Gaussian statistics for the laser phase noise. In the evaluation it is accounted for that the laser phase noise is filtered in the correlation signal d...

  11. A Dual-Band Antenna for RF Energy Harvesting Systems in Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    A. Bakkali

    2016-01-01

    Full Text Available In this paper, we focus on ambient radio frequency energy available from commercial broadcasting stations in order to provide a system based on RF energy harvesting using a new design of receiving antenna. Several antenna designs have been proposed for use in RF energy harvesting systems, as a pertinent receiving antenna design is highly required since the antenna features can affect the amount of energy harvested. The proposed antenna is aimed at greatly increasing the energy harvesting efficiency over Wi-Fi bands: 2.45 GHz and 5 GHz. This provides a promising alternative energy source in order to power sensors located in harsh environments or remote places, where other energy sources are impracticable. The dual-band antenna can be easily integrated with RF energy harvesting system on the same circuit board. Simulations and measurements were carried out to evaluate the antenna performances and investigate the effects of different design parameters on the antenna performance. The receiving antenna meets the required bandwidth specification and provides peak gain of more than 4 dBi across the operating band.

  12. Integrated design and analysis of RF heating and current drive systems

    Energy Technology Data Exchange (ETDEWEB)

    Ryan, P.M.; Carter, M.D.; Goulding, R.H.; Batchelor, D.B.; Jaeger, E.F.; Stallings, D.C.; Wang, C.Y.; Baity, F.W.; Bell, G.L.; Bigelow, T.S.; England, A.C.; Hanson, G.R.; Haste, G.R.; Hoffman, D.J.; Murakami, M.; Rasmussen, D.A.; Wilgen, J.B. [Oak Ridge National Laboratory, Oak Ridge, Tennessee 37831-8071 (United States); Rogers, J.H.; Majeski, R.; Schilling, G.; Wilson, J.R. [Princeton Plasma Physics Laboratory, Princeton, New Jersey (United States); Bhatnagar, V.; Bures, M.; Kaye, A.; Start, D.; Wade, T. [JET Joint Undertaking, Abingdon (United Kingdom); Ho, Y.L.; Kruger, W. [SAIC-McLean, Virginia (United States); TFTR ICH Team% JET ICH Team

    1996-02-01

    The design, analysis, and performance evaluation of rf power systems ultimately requires accurate modeling of a chain of subsystems starting with the rf transmitter and ending with the power absorption in the plasma. A collection of computer codes is used at ORNL to calculate the plasma loading and wave spectrum for a three-dimensional rf antenna, the transmission/reflection properties of the Faraday shield and its effect on the electrical characteristics and phase velocity of the antenna, the internal coupling among antenna array components and the incorporation of the antenna array into a transmission line model of the phase control, tuning, matching, and power distribution system. Some codes and techniques are more suited for the rapid evaluation of system design progressions, while others are more applicable to the detailed analysis of final designs or existing hardware. The interaction of codes and the accuracy of calculations will be illustrated by the process of determining the plasma loading as a function of phasing and density profiles for the TFTR ICRH antennas and comparing the results to measurements. An example of modeling a complex antenna geometry will be the comparison of calculations with the measured electrical response of a four-strap mockup of the JET A2 antenna array which was loaned to ORNL by the JET ICRH team. {copyright} {ital 1996 American Institute of Physics.}

  13. Integrated design and analysis of RF heating and current drive systems

    Science.gov (United States)

    Ryan, P. M.; Carter, M. D.; Goulding, R. H.; Batchelor, D. B.; Jaeger, E. F.; Stallings, D. C.; Wang, C. Y.; Baity, F. W.; Bell, G. L.; Bigelow, T. S.; England, A. C.; Hanson, G. R.; Haste, G. R.; Hoffman, D. J.; Murakami, M.; Rasmussen, D. A.; Wilgen, J. B.; Rogers, J. H.; Majeski, R.; Schilling, G.; Wilson, J. R.; Bhatnagar, V.; Bures, M.; Kaye, A.; Start, D.; Wade, T.; Ho, Y. L.; Kruger, W.

    1996-02-01

    The design, analysis, and performance evaluation of rf power systems ultimately requires accurate modeling of a chain of subsystems starting with the rf transmitter and ending with the power absorption in the plasma. A collection of computer codes is used at ORNL to calculate the plasma loading and wave spectrum for a three-dimensional rf antenna, the transmission/reflection properties of the Faraday shield and its effect on the electrical characteristics and phase velocity of the antenna, the internal coupling among antenna array components and the incorporation of the antenna array into a transmission line model of the phase control, tuning, matching, and power distribution system. Some codes and techniques are more suited for the rapid evaluation of system design progressions, while others are more applicable to the detailed analysis of final designs or existing hardware. The interaction of codes and the accuracy of calculations will be illustrated by the process of determining the plasma loading as a function of phasing and density profiles for the TFTR ICRH antennas and comparing the results to measurements. An example of modeling a complex antenna geometry will be the comparison of calculations with the measured electrical response of a four-strap mockup of the JET A2 antenna array which was loaned to ORNL by the JET ICRH team.

  14. Uncoupled achromatic condition of a dog-leg system with the presence of RF cavities

    CERN Document Server

    Geng, Huiping

    2013-01-01

    To merge the beam from either of the two injectors to the main linac, a dog-leg system will be employed in the second Medium Energy Beam Transport (MEBT2) line of the China ADS driving accelerator. The achromatic condition has to be guaranteed to avoid beam center excursion against energy jitter. RF cavities were found indispensable to control the bunch length growth in the dog-leg system of MEBT2. The full uncoupling between transverse and longitudinal plane is desired to minimize the growth of projected rms emittances. The uncoupled achromatic condition of this dogleg system with the presence of RF bunching cavities will be deduced using the method of transfer matrixes. It is found that to fulfil the uncoupling condition, the distance between the bunching cavities is uniquely determined by the maximum energy gain of the RF cavities. The theoretical analysis is verified by the simulation code TraceWin. The space charge effect on the uncoupled achromatic condition and the beam emittance growth will also be di...

  15. Beam Pipe HOM Absorber for 750 MHz RF Cavity Systems

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, Rolland; Neubauer, Michael

    2014-10-29

    This joint project of Muons, Inc., Cornell University and SLAC was supported by a Phase I and Phase II grant monitored by the SBIR Office of Science of the DOE. Beam line HOM absorbers are a critical part of future linear colliders. The use of lossy materials at cryogenic temperatures has been incorporated in several systems. The design in beam pipes requires cylinders of lossy material mechanically confined in such a way as to absorb the microwave energy from the higher-order modes and remove the heat generated in the lossy material. Furthermore, the potential for charge build-up on the surface of the lossy material requires the conductivity of the material to remain consistent from room temperature to cryogenic temperatures. In this program a mechanical design was developed that solved several design constraints: a) fitting into the existing Cornell load vacuum component, b) allowing the use of different material compositions, c) a thermal design that relied upon the compression of the lossy ceramic material without adding stress. Coating experiments were performed that indicated the design constraints needed to fully implement this approach for solving the charge build-up problem inherent in using lossy ceramics. In addition, the ACE3P program, used to calculate the performance of lossy cylinders in beam pipes in general, was supported by this project. Code development and documentation to allow for the more wide spread use of the program was a direct result of this project was well.

  16. Si-based RF MEMS components.

    Energy Technology Data Exchange (ETDEWEB)

    Stevens, James E.; Nordquist, Christopher Daniel; Baker, Michael Sean; Fleming, James Grant; Stewart, Harold D.; Dyck, Christopher William

    2005-01-01

    Radio frequency microelectromechanical systems (RF MEMS) are an enabling technology for next-generation communications and radar systems in both military and commercial sectors. RF MEMS-based reconfigurable circuits outperform solid-state circuits in terms of insertion loss, linearity, and static power consumption and are advantageous in applications where high signal power and nanosecond switching speeds are not required. We have demonstrated a number of RF MEMS switches on high-resistivity silicon (high-R Si) that were fabricated by leveraging the volume manufacturing processes available in the Microelectronics Development Laboratory (MDL), a Class-1, radiation-hardened CMOS manufacturing facility. We describe novel tungsten and aluminum-based processes, and present results of switches developed in each of these processes. Series and shunt ohmic switches and shunt capacitive switches were successfully demonstrated. The implications of fabricating on high-R Si and suggested future directions for developing low-loss RF MEMS-based circuits are also discussed.

  17. Developement and initial operation of a 6 GHz subsystem for the RF control system of the S-DALINAC

    Energy Technology Data Exchange (ETDEWEB)

    Burandt, Christoph; Bonnes, Uwe; Eichhorn, Ralf; Konrad, Martin; Nonn, Patrick; Enders, Joachim [Institut fuer Kernphysik, Technische Universitaet Darmstadt (Germany)

    2011-07-01

    During 2010 a source of polarized electrons has been installed at the S-DALINAC. Spatial constraints as well as limited cathode charge lifetime necessitate an efficient compression of the electron bunches before they enter the superconducting accelerating cavities. The new injector design therefore contains a harmonic prebunching system consisting of two cavities operated at 3 GHz and 6 GHz, respectively. While 3 GHz components are at hand, 6 GHz components had to be developed and integrated into the new RF control system. The basic idea of the new digital control system is the down conversion of the RF signals to the base band. Therefore the low frequency part of each system can be used without adaptions, while the RF module required redevelopment. This talk covers the redesign of the existing 3 GHz RF module for 6 GHz and first experiences from the commissioning of the new prebuncher system at the S-DALINAC.

  18. Development of Low Level RF Control Systems for Superconducting Heavy Ion Linear Accelerators, Electron Synchrotrons and Storage Rings

    CERN Document Server

    Aminov, Bachtior; Kolesov, Sergej; Pekeler, Michael; Piel, Christian; Piel, Helmut

    2005-01-01

    Since 2001 ACCEL Instruments is supplying low level RF control systems together with turn key cavity systems. The early LLRF systems used the well established technology based on discrete analogue amplitude and phase detectors and modulators. Today analogue LLRF systems can make use of advanced vector demodulators and modulators combined with a fast computer controlled analogue feed back loop. Feed forward control is implemented to operate the RF cavity in an open loop mode or to compensate for predictable perturbations. The paper will introduce the general design philosophy and show how it can be adapted to different tasks as controlling a synchrotron booster nc RF system at 500 MHz, or superconducting storage ring RF cavities, as well as a linear accelerator at 176 MHz formed by a chain of individually driven and controlled superconducting λ/2 cavities.

  19. 基于GSM和nRF24L01的环境监测报警系统设计%Design of Environmental detection and alarm system based on GSM and nRF24L01

    Institute of Scientific and Technical Information of China (English)

    雷宁

    2015-01-01

    本文设计了一种基于GSM和nRF24L01的环境监控报警系统,实现对人体红外、温湿度、天然气浓度、火焰等信号的实时检测,并将检测结果显示于TFT屏幕,出现危险情况启动语音报警,并通过移动网络迅速与用户设置好的手机通信。系统运行稳定、操作方便,适合智能楼宇,家居住宅,企业厂区的远程安防。%This paper presents a design of environmental detection and alarm system based on GSM and nRF24L01,it provides real-time detection of the signal of Infrared radiation of human body,temperature and humidity,gas concentration and flame,then the test results are displayed on TFT.When dangerous appear,the system start voice alarm at once,and quickly set a communication with the user through the mobile phone network.The system is stable,easy to operate,suitable for remote security for intelligent buildings, house,company and factories.

  20. The dielectric properties of human pineal gland tissue and RF absorption due to wireless communication devices in the frequency range 400-1850 MHz

    Energy Technology Data Exchange (ETDEWEB)

    Schmid, Gernot [Austrian Research Centers GmbH-ARC, ITM, A-2444 Seibersdorf (Austria); Ueberbacher, Richard [Austrian Research Centers GmbH-ARC, ITM, A-2444 Seibersdorf (Austria); Samaras, Theodoros [Department of Physics, Aristotle University of Thessaloniki, GR-54124 Thessaloniki (Greece); Tschabitscher, Manfred [Center of Anatomy and Cell Biology, Medical University of Vienna, A-1090 Vienna (Austria); Mazal, Peter R [Department of Clinical Pathology, Medical University Vienna, A-1090 Vienna (Austria)

    2007-09-07

    In order to enable a detailed analysis of radio frequency (RF) absorption in the human pineal gland, the dielectric properties of a sample of 20 freshly removed pineal glands were measured less than 20 h after death. Furthermore, a corresponding high resolution numerical model of the brain region surrounding the pineal gland was developed, based on a real human tissue sample. After inserting this model into a commercially available numerical head model, FDTD-based computations for exposure scenarios with generic models of handheld devices operated close to the head in the frequency range 400-1850 MHz were carried out. For typical output power values of real handheld mobile communication devices, the obtained results showed only very small amounts of absorbed RF power in the pineal gland when compared to SAR limits according to international safety standards. The highest absorption was found for the 400 MHz irradiation. In this case the RF power absorbed inside the pineal gland (organ mass 96 mg) was as low as 11 {mu}W, when considering a device of 500 mW output power operated close to the ear. For typical mobile phone frequencies (900 MHz and 1850 MHz) and output power values (250 mW and 125 mW) the corresponding values of absorbed RF power in the pineal gland were found to be lower by a factor of 4.2 and 36, respectively. These results indicate that temperature-related biologically relevant effects on the pineal gland induced by the RF emissions of typical handheld mobile communication devices are unlikely.

  1. Communication System Architecture for Planetary Exploration

    Science.gov (United States)

    Braham, Stephen P.; Alena, Richard; Gilbaugh, Bruce; Glass, Brian; Norvig, Peter (Technical Monitor)

    2001-01-01

    Future human missions to Mars will require effective communications supporting exploration activities and scientific field data collection. Constraints on cost, size, weight and power consumption for all communications equipment make optimization of these systems very important. These information and communication systems connect people and systems together into coherent teams performing the difficult and hazardous tasks inherent in planetary exploration. The communication network supporting vehicle telemetry data, mission operations, and scientific collaboration must have excellent reliability, and flexibility.

  2. On the performance of mixed RF/FSO dual-hop transmission systems

    KAUST Repository

    Ansari, Imran Shafique

    2013-06-01

    In this work, the performance analysis of a dualhop relay transmission system composed of asymmetric radio-frequency (RF)/free-space optical (FSO) links is presented. This work is based on the fact that FSO links are cost-effective, license-free and can provide even higher bandwidths compared to the traditional RF links. More specifically, in this work, we build on the cumulative distribution function presented in [1] to derive new exact closed-form expressions for the probability density function, moment generating function, and moments of the end-to-end signal-to-noise ratio. We then capitalize on these results to offer new exact closed-form expressions for the higherorder amount of fading, average error rate for binary and M-ary modulation schemes, and ergodic capacity, all in terms of Meijer\\'s G functions. Our new analytical results were also verified via computer-based Monte-Carlo simulation results. © 2013 IEEE.

  3. New Control Structure of the 10 MHz RF System in the CERN PS

    CERN Document Server

    Damerau, H

    2013-01-01

    The 10MHz cavities comprise the main RF system in the CERN PS and the only one that allows acceleration. In total 11 tunable cavities (10 operational and a hot spare, grouped into 3+1 tuning groups and up to presently 6 voltage program groups) are distributed all around the circumference of the PS ring. Next to the RF drive signal each of the cavities is controlled by a voltage program and timing pulses to open and close the relays to short-circuit the cavity gaps. These control signals are presently generated by a dedicated hardware matrix. It translates voltage functions and relay timing pulses per cavity group into functions and timings per cavity. However, due to its central position in the RF beam control system, the dedicated hardware matrix can cause significant downtime in case of a major hardware failure. Instead of upgrading the existing obsolete hardware, this note suggests a replacement by standard controls hardware and dedicated application software. Thanks to advanced software concepts like “M...

  4. Photonic-Based RF Transceiver for UWB Multi-Carrier Wireless Systems

    Directory of Open Access Journals (Sweden)

    Filippo Scotti

    2014-05-01

    Full Text Available In this paper an all-optical system exploitable as the core structure for a photonic-based RF transceiver is presented. The proposed scheme is able to simultaneously perform either up- or down-conversion of multiple frequency Ultra-Wide Band (UWB RF signals, employing a single Mode-Locking Laser (MLL. The system has been experimentally demonstrated and tested by up- and down-converting orthogonal frequency division multiplexing (OFDM signals over a bandwidth of about 4 GHz. The scheme’s performance has been validated by measuring the error vector magnitude (EVM of the OFDM signals over the whole considered RF spectrum (from 5 GHz to 26.5 GHz, both in up-conversion and in down-conversion. The measurements show negligible power penalties, lower than 0.5 dB. Since the proposed scheme can act either as an up- or down-converter, and it is composed by easily integratable devices, two identical structures can be combined on a single integrated platform, sharing a single MLL, to build a compact and efficient UWB transceiver.

  5. Communications satellite system for Africa

    Science.gov (United States)

    Kriegl, W.; Laufenberg, W.

    1980-09-01

    Earlier established requirement estimations were improved upon by contacting African administrations and organizations. An enormous demand is shown to exist for telephony and teletype services in rural areas. It is shown that educational television broadcasting should be realized in the current African transport and communications decade (1978-1987). Radio broadcasting is proposed in order to overcome illiteracy and to improve educational levels. The technical and commercial feasibility of the system is provided by computer simulations which demonstrate how the required objectives can be fulfilled in conjunction with ground networks.

  6. Low level rf system for the European Spallation Source’s Bilbao linac

    Directory of Open Access Journals (Sweden)

    Hooman Hassanzadegan

    2011-05-01

    Full Text Available Design and some performance results of the pulsed digital low level radio frequency (LLRF for the radio frequency quadrupole (RFQ systems of Rutherford Appleton Laboratory–front end test stand and the future European Spallation Source Bilbao linac are presented. For rf field regulation, the design is based on direct rf-to-baseband conversion using an analog in-phase quadrature (IQ demodulator, high-speed sampling of the I/Q components, baseband signal processing in a field-programmable gate array (FPGA, conversion to analog, and IQ modulation. This concept leads to a simple and versatile LLRF system which can be used for a large variety of rf frequencies and virtually any LLRF application including cw, ramping, and pulsed. In order to improve the accuracy of the probe voltage measurement, errors associated with the use of analog IQ demodulators have been identified and corrected by FPGA algorithms and proper setting of the feedback loop parameters. Furthermore, a baseband-equivalent model for the rf plant is developed in MATLAB-Simulink to study the RFQ transient response under beam loading in the presence of phase and delay errors. The effect of the unwanted resonant modes on the feedback loop stability and the LLRF considerations to avoid such instabilities are discussed and compared to some other machines such as the ILC and the European free electron laser . The practical results obtained from tests with a mock-up cavity and an RFQ cold model verify that amplitude and phase stabilities down to a fraction of one percent and one degree and phase margins larger than ±50° can be achieved with this method preserving the linearity and bandwidth of the feedback loops.

  7. Optoelectronic Oscillators for Communication Systems

    Science.gov (United States)

    Romeira, Bruno; Figueiredo, José

    We introduce and report recent developments on a novel five port optoelectronic voltage controlled oscillator consisting of a resonant tunneling diode (RTD) optical-waveguide integrated with a laser diode. The RTD-based optoelectronic oscillator (OEO) has both optical and electrical input and output ports, with the fifth port allowing voltage control. The RTD-OEO locks to reference radio-frequency (RF) sources by either optical or electrical injection locking techniques allowing remote synchronization, eliminating the need of impedance matching between traditional RF oscillators. RTD-OEO functions include generation, amplification and distribution of RF carriers, clock recovery, carrier recovery, modulation and demodulation and frequency synthesis. Self-injection locking operation modes, where small portions of the output electrical/optical signals are fed back into the electrical/optical input ports, are also proposed. The self-phase locked loop configuration can give rise to low-noise high-stable oscillations, not limited by the RF source performance and with no need of external optoelectronic conversion.

  8. Technical Solution for Mitigating Radio-Frequency (RF) Interference to Air Traffic Control Communications

    Science.gov (United States)

    2013-09-01

    significant disadvantages to this solution were (1) use of an additional fiber-optic data system in the test setup and (2) the inability to quickly...GRAVES 1 119TH CACS (PDF) ATTN MSGT R PITTMAN 1 134 CS/ SCM (PDF) ATTN TSGT L DAVIS 1 AFWET ESC/HNAS (PDF) ATTN C KRAWCZYK 2

  9. RF MEMS capacitors and Variable Capacitors – The Future of Wireless Communication

    KAUST Repository

    Elshurafa, Amro M.

    2014-07-15

    The most recent 4G devices are designed with specific emphasis on the data traffic challenge. Because there is an increasing number of bands, all the circuits and devices related to the design of wireless systems need to be enhanced including the power am

  10. Wireless Augmented Reality Communication System

    Science.gov (United States)

    Devereaux, Ann (Inventor); Jedrey, Thomas (Inventor); Agan, Martin (Inventor)

    2016-01-01

    The system of the present invention is a highly integrated radio communication system with a multimedia co-processor which allows true two-way multimedia (video, audio, data) access as well as real-time biomedical monitoring in a pager-sized portable access unit. The system is integrated in a network structure including one or more general purpose nodes for providing a wireless-to-wired interface. The network architecture allows video, audio and data (including biomedical data) streams to be connected directly to external users and devices. The portable access units may also be mated to various non-personal devices such as cameras or environmental sensors for providing a method for setting up wireless sensor nets from which reported data may be accessed through the portable access unit. The reported data may alternatively be automatically logged at a remote computer for access and viewing through a portable access unit, including the user's own.

  11. RF and data acquisition systems for Fermilab's ILC SRF cavity vertical test stand

    Energy Technology Data Exchange (ETDEWEB)

    Ozelis, Joseph P.; Nehring, Roger; /Fermilab; Grenoble, Christiana; Powers, Thomas J.; /Jefferson Lab

    2007-06-01

    Fermilab is developing a facility for vertical testing of SRF cavities as part of its ILC program. The RF system for this facility is based on the proven production cavity test systems used at Jefferson Lab for CEBAF and SNS cavity testing. The design approach is modular in nature, using commercial-off-the-shelf (COTS) components. This yields a system that can be easily debugged and modified, and with ready availability of spares. Comprehensive data acquisition and control is provided by a PXI-based hardware platform in conjunction with software developed in the LabView programming environment.

  12. Do Animal Communication Systems Have Phonemes?

    Science.gov (United States)

    Bowling, Daniel L; Fitch, W Tecumseh

    2015-10-01

    Biologists often ask whether animal communication systems make use of conceptual entities from linguistics, such as semantics or syntax. A new study of an Australian bird species argues that their communication system has phonemes, but we argue that imposing linguistic concepts obscures, rather than clarifyies, communicative function. Copyright © 2015 Elsevier Ltd. All rights reserved.

  13. Communications Technology Assessment for the Unmanned Aircraft System (UAS) Control and Non-Payload Communications (CNPC) Link

    Science.gov (United States)

    Bretmersky, Steven C.; Bishop, William D.; Dailey, Justin E.; Chevalier, Christine T.

    2014-01-01

    The National Aeronautics and Space Administration (NASA) Glenn Research Center (GRC) is performing communications systems research for the Unmanned Aircraft System (UAS) in the National Airspace System (NAS) Project. One of the goals of the communications element is to select and test a communications technology for the UAS Control and Non-Payload Communications (CNPC) link. The GRC UAS Modeling and Simulation (M/S) Sub Team will evaluate the performance of several potential technologies for the CNPC link through detailed software simulations. In parallel, an industry partner will implement a technology in hardware to be used for flight testing. The task necessitated a technical assessment of existing Radio Frequency (RF) communications technologies to identify the best candidate systems for use as the UAS CNPC link. The assessment provides a basis for selecting the technologies for the M/S effort and the hardware radio design. The process developed for the technical assessments for the Future Communications Study1 (FCS) was used as an initial starting point for this assessment. The FCS is a joint Federal Aviation Administration (FAA) and Eurocontrol study on technologies for use as a future aeronautical communications link. The FCS technology assessment process methodology can be applied to the UAS CNPC link; however the findings of the FCS are not directly applicable because of different requirements between a CNPC link and a general aeronautical data link. Additional technologies were added to the potential technologies list from the State of the Art Unmanned Aircraft System Communication Assessment developed by NASA GRC2. This document investigates the state of the art of communications as related to UAS. A portion of the document examines potential communications systems for a UAS communication architecture. Like the FCS, the state of the art assessment surveyed existing communications technologies. It did not, however, perform a detailed assessment of the

  14. Modeling of digital communication systems using SIMULINK

    CERN Document Server

    Giordano, Arthur A

    2015-01-01

    Arthur Giordano, PhD, is a consultant in the field of military and commercial communications specializing in wireless communications. He is a co-founder of G5 Scientific, LLC, is a senior member of the IEEE and has taught graduate communications courses. He has developed numerous models using MathWorks®' SIMULINK®® to characterize digital communications systems. Allen Levesque, PhD, is a consultant specializing in digital communications systems, and is a partner in G5 Scientific, LLC. He has taught graduate courses in digital communications at Worcester Polytechnic Institute and is currently

  15. Cognitive Cellular Systems: A New Challenge on the RF Analog Frontend

    Science.gov (United States)

    Varga, Gabor; Schrey, Moritz; Subbiah, Iyappan; Ashok, Arun; Heinen, Stefan

    2016-07-01

    Cognitive Cellular Systems are seen today as one of the most promising ways of moving forward solving or at least easing the still worsening situation of congested spectrum caused by the growing number of users and the expectation of higher data transfer rates. As the intelligence of a Cognitive Radio system is located in the digital domain - the Cognitive Engine and associated layers - extensive research has been ongoing in that domain since Mitola published his idea in 1999. Since, a big progress has been made in the domain of architectures and algorithms making systems more efficient and highly flexible. The pace of this progress, however, is going to be impeded by hard requirements on the received and transmitted signal quality, introducing ultimate challenges on the performance of the RF analog frontend, such as in-band local oscillator harmonics, ultra low sensitivity and ultra high linearity. The RF frontend is thus likely to become the limiting technical factor in the true realization of a Cognitive Cellular System. Based on short recapitulations of the most crucial issues in RF analog design for Cognitive Systems, this article will point out why those mechanisms become responsible for the limitation of the overall performance particularly in a broadband Cognitive Cellular System. Furthermore, as part of a possible solution to ease the situation, system design of a high intermediate frequency (IF) to UHF frequency converter for cognitive radios is discussed and the performance of such a converter analyzed as a proof of concept. In addition to successfully tackling some of the challenges, such a high-IF converter enables white space operation for existing commercial devices by acting as frequency converter. From detailed measurements, the capabilities in both physical layer and application layer performance of a high-IF frontend developed out of off-the-shelf components is explained and is shown to provide negligible degradation to the commercial device

  16. Design and Tests of 500kW RF Windows for the ITER LHCD System

    CERN Document Server

    Hillairet, Julien; Faure, N; Achard, J; Delpech, L; Goniche, M; Larroque, S; Magne, R; Marfisi, L; Park, S; Poli, S; Dechambre, N; Vulliez, K

    2015-01-01

    In the frame of a R\\&D effort conducted by CEA toward the design and the qualification of a 5 GHz LHCD system for the ITER tokamak, two 5 GHz 500 kW/5 s windows have been designed, manufactured and tested at high power in collaboration with the National Fusion Research Institute (NFRI). The window design rely on a symmetrical pill-box concept with a cylindrical beryllium oxide ceramic brazed on an actively water cooled copper skirt. The ceramic RF properties have been measured on a test sample to get realistic values for guiding the design. Low power measurements of the manufactured windows show return losses below-32 dB and insertion losses between-0.01 dB and-0.05 dB, with an optimum frequency shifted toward lower frequencies. High power tests conducted at NFRI show unexpected total power loss for both windows. The ceramic temperature during RF pulses has been found to reach unexpected high temperature, preventing these windows to be used under CW conditions. A post-mortem RF analysis of samples taken f...

  17. Design and research of RF system for 10 MeV compact cyclotron

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    A 10 MeV compact cyclotron (CYCHU-10) has been developing in Huazhong University of Science and Technology (HUST). The RF system includes a 10 kW RF power generator and a resonance cavity. There is no automatic frequency tuning equipment in the cavity due to space limitations, so the generator must search and track the cavity resonant frequency. AD9850 synthesizer is used to generate RF signal in the experimental prototype, and a fine sinusoidal waveform around 99 MHz is obtained with the method of picking up a special aliased signal from the synthesizer’s output, and the output power level can be set by regulating the resistor connected to the Pin ’Rset’. The final stage amplifier based on tetrode operates in the grounded cathode configuration, and the schematic of the tetrode circuit is illustrated. The method of searching the resonant frequency is discussed in detail. For the sake of a compact and robust structure, the resonance cavity will adopt non-uniform characteristic impedance coaxial structure, and the magnet surface electroplated with copper will be used as dummy Dees. The precise shapes and dimensions of the cavity are designed and simulation results are carried out in this paper. The distributions of electromagnetic field are illustrated by means of numerical calculation analysis, and the wooden model test is preformed as well.

  18. RF Micro-Electro-Mechanical Systems Capacitive Switches Using Ultra Thin Hafnium Oxide Dielectric

    Science.gov (United States)

    Zhang, Yi; Onodera, Kazumasa; Maeda, Ryutaro

    2006-01-01

    A π-type RF capacitive switch using about 45-nm-thick HfO2 dielectric layer was fabricated. High isolation performance was obtained in wide-band range when the switch was down-state. The isolation was better than -40 dB at the frequency range of 4-35 GHz. Particularly, the isolation was better than -50 dB in the frequency range of 8-12 GHz, i.e., X band. HfO2 showed excellent process compatibility with conventional microfabrication procedure. The 45-nm-thick HfO2 film was prepared using sputtering at room temperature so that it was feasible to be integrated into RF switch and other microwave circuits. The results of constant bias stressing showed that the ultra thin HfO2 had excellent reliability. The electric breakdown of HfO2 was observed, which had no apparent negative effects on the reliability of the dielectric. HfO2 dielectrics were attractive in the application of RF micro-electro-mechanical systems (MEMS) switch for new generation of low-loss high-linearity microwave circuits.

  19. On the Performance Analysis of Dual-Hop Mixed FSO/RF Systems

    KAUST Repository

    Zedini, Emna

    2016-02-03

    This paper presents novel results for the performance analysis of dual-hop free-space optical/radio frequency (FSO/RF) transmission systems where the FSO link is modeled by the Gamma-Gamma distribution with pointing error impairments and under both heterodyne detection and intensity modulation with direct detection (IM/DD), and the RF link experiences the Generalized Nakagami-m fading. Using amplify-and-forward fixed-gain relaying as well as channel-state-information(CSI)- assisted relaying, we derive closed-form expressions for the outage probability, the average bit-error rate (BER), and the ergodic capacity in terms of the bivariate H-Fox function. For a special case, we obtain simplified results for Nakagami-m fading channels in the RF link. Further, new asymptotic results for the outage probability and the average BER at high signal-to-noise ratio (SNR) regime are presented in terms of simple functions. Numerical and Monte-Carlo simulation results are provided to verify the accuracy of the newly proposed results, and a perfect agreement is observed.

  20. Advances in communication systems and electrical engineering

    CERN Document Server

    Huang, Xu

    2008-01-01

    This volume contains contributions from participants in the 2007 International Multiconference of Engineers and Computer Scientists Topics covered include communications theory, communications protocols, network management, wireless networks, telecommunication, electronics, power engineering, control engineering, signal processing, and industrial applications. The book will offer the states of arts of tremendous advances in communication systems and electrical engineering and also serve as an excellent reference work for researchers and graduate students working with/on communication systems a

  1. The UHV system of the 10 MeV RF electron linac

    Science.gov (United States)

    Bhattacharjee, D.; Jayaprakash, D.; Mishra, R. L.; Nimje, V. T.; Mittal, K. C.

    2008-05-01

    A 10 MeV, 10 kW RF Electron Linac, for Industrial applications, is installed and commissioned at Electron Beam Centre (EBC), Kharghar, Navi Mumbai. The accelerator consists of the electron gun, RF Linac, Vacuum system, Beam diagnostics system, Magnetic sweep scanning system and Scan horn. The accelerator is divided into three sections with gate valves to isolate them, to enable servicing of pumps and modifications. The vacuum requirement in the accelerator is 10-7 mbar considering the breakdown parameters of the RF field within the linac. Total length of the accelerator from electron gun to the scan horn is about 5.0 meters. Vacuum plumb lines are of SS 304 pipes of nominal bores of 100 mm and 150 mm, machined internally to a surface finish of 0.8 μm. It encloses a volume of 156 litres. Total surface area exposed to vacuum is 57,500 cm2. It consists of 5250 cm2 of OFHC Copper, 51300 cm2 of SS 304 and 940 cm2 of ceramic sections. Leak-tightness of the order of 1 × 10-9mbar.l/s is ensured for the whole system, after eliminating the leaks at every stage of the assembly. Baking the plumb line and pumps at 150° C, for eight hours an ultimate vacuum of 2 × 10-7mbar is achieved in the accelerator. Modifications of the vacuum system is undertaken to suit the design changes in the gun and the diagnostic systems.

  2. The UHV system of the 10 MeV RF electron linac

    Energy Technology Data Exchange (ETDEWEB)

    Bhattacharjee, D; Jayaprakash, D; Mishra, R L; Nimje, V T; Mittal, K C [D. Bhattacharjee, Accelerator and Pulse Power Division, Bhabha Atomic Research Centre, Trombay, Mumbai, 400 085 (India)], E-mail: dhruvab@barc.gov.in

    2008-05-01

    A 10 MeV, 10 kW RF Electron Linac, for Industrial applications, is installed and commissioned at Electron Beam Centre (EBC), Kharghar, Navi Mumbai. The accelerator consists of the electron gun, RF Linac, Vacuum system, Beam diagnostics system, Magnetic sweep scanning system and Scan horn. The accelerator is divided into three sections with gate valves to isolate them, to enable servicing of pumps and modifications. The vacuum requirement in the accelerator is 10{sup -7} mbar considering the breakdown parameters of the RF field within the linac. Total length of the accelerator from electron gun to the scan horn is about 5.0 meters. Vacuum plumb lines are of SS 304 pipes of nominal bores of 100 mm and 150 mm, machined internally to a surface finish of 0.8 {mu}m. It encloses a volume of 156 litres. Total surface area exposed to vacuum is 57,500 cm{sup 2}. It consists of 5250 cm{sup 2} of OFHC Copper, 51300 cm{sup 2} of SS 304 and 940 cm{sup 2} of ceramic sections. Leak-tightness of the order of 1 x 10{sup -9}mbar.l/s is ensured for the whole system, after eliminating the leaks at every stage of the assembly. Baking the plumb line and pumps at 150 deg. C, for eight hours an ultimate vacuum of 2 x 10{sup -7}mbar is achieved in the accelerator. Modifications of the vacuum system is undertaken to suit the design changes in the gun and the diagnostic systems.

  3. Design and Preparation of RF System for the Lower Hybrid Fast Wave Heating and Current Drive Research on VEST

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Sun Ho; Jeong, Seung Ho [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Lee, Hyun Woo; Lee, Byung Je [Kwang Woon University, Chuncheon (Korea, Republic of); Jo, Jong Gab; Lee, Hyun Young; Hwang, Yong Seok [Seoul National University, Seoul (Korea, Republic of)

    2015-10-15

    Continuous current drive is one of the key issues for tokamak to be a commercial fusion reactor. As a part of new and efficient current drive concept research by using a Lower Hybrid Fast Wave (LHFW), the experimental study is planned on Versatile Experiment Spherical Torus (VEST) and a RF system is being developed in collaboration with Kwang Woon University (KWU), Korea Accelerator Plasma Research Association (KAPRA) and Seoul National University (SNU). The LHFW RF system includes UHF band klystron, inter-digital antenna, RF diagnostics and power transmission sub components such as circulator, DC breaker, vacuum feed-thru. The design and preparation status of the RF system will be presented in the meeting in detail. A RF system has been designed and prepared for the experimental study of efficient current drive by using Lower Hybrid Fast Wave. Overall LHFW RF system including diagnostics is designed to deliver about 10 kW in UHF band. And the key hardware components including klystron and antenna are being prepared and designed through the collaboration with KWU, KAPRA and SNU.

  4. Rectifier Design Challenges for RF Wireless Power Transfer and Energy Harvesting Systems

    Directory of Open Access Journals (Sweden)

    A. Collado

    2017-06-01

    Full Text Available The design of wireless power transfer (WPT and energy harvesting (EH solutions poses different challenges towards achieving maximum RF-DC conversion efficiency in these systems. This paper covers several selected challenges when developing WPT and electromagnetic EH solutions, such as the design of multiband and broadband rectifiers, the minimization of the effect that load and input power variations may have on the system performance and finally the most optimum power combining mechanisms that can be used when dealing with multi-element rectifiers.

  5. Exposure system to study hypotheses of ELF and RF electromagnetic field interactions of mobile phones with the central nervous system.

    Science.gov (United States)

    Murbach, Manuel; Christopoulou, Maria; Crespo-Valero, Pedro; Achermann, Peter; Kuster, Niels

    2012-09-01

    A novel exposure system for double-blind human electromagnetic provocation studies has been developed that satisfies the precision, control of fields and potential artifacts, and provides the flexibility to investigate the response of hypotheses-driven electromagnetic field exposure schemes on brain function, ranging from extremely low frequency (ELF) to radio frequency (RF) fields. The system can provide the same exposure of the lateral cerebral cortex at two different RF frequencies (900 and 2140 MHz) but with different exposure levels at subcortical structures, and also allows uniform ELF magnetic field exposure of the brain. The RF modulation and ELF signal are obtained by a freely programmable arbitrary signal generator allowing a wide range of worst-case exposure scenarios to be simulated, including those caused by wireless devices. The maximum achievable RF exposure is larger than 60 W/kg peak spatial specific absorption rate averaged over 10 g of tissue. The maximum ELF magnetic field exposure of the brain is 800 A/m at 50 Hz with a deviation from uniformity of 8% (SD).

  6. RF Circuit Design in Nanometer CMOS

    OpenAIRE

    Nauta, Bram

    2007-01-01

    With CMOS technology entering the nanometer regime, the design of analog and RF circuits is complicated by low supply voltages, very non-linear (and nonquadratic) devices and large 1/f noise. At the same time, circuits are required to operate over increasingly wide bandwidths to implement modern multi-band communication systems as these systems move toward software-defined radio. These trends in technology and system design call for a re-thinking of analog and RF circuit design in nanometer C...

  7. New Military Strategic Communications System

    Science.gov (United States)

    2007-05-01

    54 O’Day, 6. 55 Perlmutter, David D. The Manship School guide to Political Communication . Louisiana State University Press...Westport: Praeger Publishing, 2006. Perlmutter, David D. The Manship School guide to Political Communication . Louisiana State University Press

  8. Smart Grid Communications System Blueprint

    Science.gov (United States)

    Clark, Adrian; Pavlovski, Chris

    2010-10-01

    Telecommunications operators are well versed in deploying 2G and 3G wireless networks. These networks presently support the mobile business user and/or retail consumer wishing to place conventional voice calls and data connections. The electrical power industry has recently commenced transformation of its distribution networks by deploying smart monitoring and control devices throughout their networks. This evolution of the network into a `smart grid' has also motivated the need to deploy wireless technologies that bridge the communication gap between the smart devices and information technology systems. The requirements of these networks differ from traditional wireless networks that communications operators have deployed, which have thus far forced energy companies to consider deploying their own wireless networks. We present our experience in deploying wireless networks to support the smart grid and highlight the key properties of these networks. These characteristics include application awareness, support for large numbers of simultaneous cell connections, high service coverage and prioritized routing of data. We also outline our target blueprint architecture that may be useful to the industry in building wireless and fixed networks to support the smart grid. By observing our experiences, telecommunications operators and equipment manufacturers will be able to augment their current networks and products in a way that accommodates the needs of the emerging industry of smart grids and intelligent electrical networks.

  9. Health Monitoring System Based on Intra-Body Communication

    Science.gov (United States)

    Razak, A. H. A.; Ibrahim, I. W.; Ayub, A. H.; Amri, M. F.; Hamzi, M. H.; Halim, A. K.; Ahmad, A.; Junid, S. A. M. Al

    2015-11-01

    This paper presents a model of a Body Area Network (BAN) health monitoring system based on Intra-Body Communication. Intra-body Communication (IBC) is a communication technique that uses the human body as a medium for electrical signal communication. One of the visions in the health care industry is to provide autonomous and continuous self and the remote health monitoring system. This can be achieved via BAN, LAN and WAN integration. The BAN technology itself consists of short range data communication modules, sensors, controller and actuators. The information can be transmitted to the LAN and WAN via the RF technology such as Bluetooth, ZigBee and ANT. Although the implementations of RF communication have been successful, there are still limitations in term of power consumption, battery lifetime, interferences and signal attenuations. One of the solutions for Medical Body Area Network (MBANs) to overcome these issues is by using an IBC technique because it can operate at lower frequencies and power consumption compared to the existing techniques. The first objective is to design the IBC's transmitter and receiver modules using the off the shelf components. The specifications of the modules such as frequency, data rate, modulation and demodulation coding system were defined. The individual module were designed and tested separately. The modules was integrated as an IBC system and tested for functionality then was implemented on PCB. Next objective is to model and implement the digital parts of the transmitter and receiver modules on the Altera's FPGA board. The digital blocks were interfaced with the FPGA's on board modules and the discrete components. The signals that have been received from the transmitter were converted into a proper waveform and it can be viewed via external devices such as oscilloscope and Labview. The signals such as heartbeats or pulses can also be displayed on LCD. In conclusion, the IBC project presents medical health monitoring model

  10. A randomized model for communicating embedded systems

    NARCIS (Netherlands)

    Bujorianu, M.C.; Bujorianu, L.M.

    2008-01-01

    Nowadays, there is an intense research activity in designing systems that operate in real life, physical environments. This research is spanned by various areas in computer science and engineering: embedded systems, reactive systems, wireless communications, hybrid systems, stochastic processes, etc

  11. Expert Systems as Tools for Technical Communicators.

    Science.gov (United States)

    Grider, Daryl A.

    1994-01-01

    Discusses expertise, what an expert system is, what an expert system shell is, what expert systems can and cannot do, knowledge engineering and technical communicators, and planning and managing expert system projects. (SR)

  12. A randomized model for communicating embedded systems

    NARCIS (Netherlands)

    Bujorianu, M.C.; Bujorianu, L.M.

    2008-01-01

    Nowadays, there is an intense research activity in designing systems that operate in real life, physical environments. This research is spanned by various areas in computer science and engineering: embedded systems, reactive systems, wireless communications, hybrid systems, stochastic processes,

  13. Effect of insulating layer material on RF-induced heating for external fixation system in 1.5 T MRI system.

    Science.gov (United States)

    Liu, Yan; Kainz, Wolfgang; Qian, Songsong; Wu, Wen; Chen, Ji

    2014-09-01

    The radio frequency (RF)-induced heating is a major concern when patients with medical devices are placed inside a magnetic resonance imaging (MRI) system. In this article, numerical studies are applied to investigate the potentials of using insulated materials to reduce the RF heating for external fixation devices. It is found that by changing the dielectric constant of the insulation material, the RF-induced heating at the tips of devices can be altered. This study indicates a potential technique of developing external fixation device with low MRI RF heating.

  14. Wireless Augmented Reality Communication System

    Science.gov (United States)

    Devereaux, Ann (Inventor); Jedrey, Thomas (Inventor); Agan, Martin (Inventor)

    2017-01-01

    A portable unit is for video communication to select a user name in a user name network. A transceiver wirelessly accesses a communication network through a wireless connection to a general purpose node coupled to the communication network. A user interface can receive user input to log on to a user name network through the communication network. The user name network has a plurality of user names, at least one of the plurality of user names is associated with a remote portable unit, logged on to the user name network and available for video communication.

  15. Transition From NASA Space Communication Systems to Commerical Communication Products

    Science.gov (United States)

    Ghazvinian, Farzad; Lindsey, William C.

    1994-01-01

    Transitioning from twenty-five years of space communication system architecting, engineering and development to creating and marketing of commercial communication system hardware and software products is no simple task for small, high-tech system engineering companies whose major source of revenue has been the U.S. Government. Yet, many small businesses are faced with this onerous and perplexing task. The purpose of this talk/paper is to present one small business (LinCom) approach to taking advantage of the systems engineering expertise and knowledge captured in physical neural networks and simulation software by supporting numerous National Aeronautics and Space Administration (NASA) and the Department of Defense (DoD) projects, e.g., Space Shuttle, TDRSS, Space Station, DCSC, Milstar, etc. The innovative ingredients needed for a systems house to transition to a wireless communication system products house that supports personal communication services and networks (PCS and PCN) development in a global economy will be discussed. Efficient methods for using past government sponsored space system research and development to transition to VLSI communication chip set products will be presented along with notions of how synergy between government and industry can be maintained to benefit both parties.

  16. Distribution system protection with communication technologies

    DEFF Research Database (Denmark)

    Wei, Mu; Chen, Zhe

    2010-01-01

    Due to the communication technologies’ involvement in the distribution power system, the time-critical protection function may be implemented more accurately, therefore distribution power systems’ stability, reliability and security could be improved. This paper presents an active distribution...... power system, including CHPs (Combined Heating and Power) and small scaled WTs (Wind Turbines), as a practical example to examine the possible impacts of communication technologies on the power system. Under some fault scenarios, the power system’s responses to the fault are compared between the system...... with communication technologies and that without communication technologies. At the same time, the previously proposed study method of combining the simulations of communication and power systems is adopted in this study. The performance of a communication network adopted for power system is simulated by OPNET...

  17. Beam manipulation and compression using broadband rf systems in the Fermilab Main Injector and Recycler

    Energy Technology Data Exchange (ETDEWEB)

    G William Foster et al.

    2004-07-09

    A novel method for beam manipulation, compression, and stacking using a broad band RF system in circular accelerators is described. The method uses a series of linear voltage ramps in combination with moving barrier pulses to azimuthally compress, expand, or cog the beam. Beam manipulations can be accomplished rapidly and, in principle, without emittance growth. The general principle of the method is discussed using beam dynamics simulations. Beam experiments in the Fermilab Recycler Ring convincingly validate the concept. Preliminary experiments in the Fermilab Main Injector to investigate its potential for merging two ''booster batches'' to produce high intensity proton beams for neutrino and antiproton production are described.

  18. A COAXIAL TE011 CAVITY AND A SYSTEM TO MEASURE DC AND RF PROPERTIES OF SUPERCONDUCTORS

    Energy Technology Data Exchange (ETDEWEB)

    Gianluigi Ciovati; Peter Kneisel; Ganapati Rao Myneni; Larry Turlington; Gary Slack; Michael Morrone; William Clemens; Richard Bundy; Thomas Elliott; Jayanta Mondal

    2008-01-23

    A coaxial niobium cavity has been designed and built where the center conductor consists of a removable sample. In addition, a system to measure properties such as magnetization, penetration depth, critical temperature and thermal conductivity on the same cylindrical sample has been designed and built. The purpose of this effort is to investigate possible correlations between DC and RF properties of superconductors. In this contribution, the design of the various components is discussed and the test results on a niobium sample obtained so far are presented.

  19. A non-IQ sampling controller in low level RF system

    Institute of Scientific and Technical Information of China (English)

    YIN Cheng-Ke; DAI Zhi-Min; LIU Jian-Fei; ZHAO Yu-Bin; ZHANG Tong-Xuan; FU Ze-Chuan; LIU Wei-Qing

    2008-01-01

    This paper describes a non-IQ controller for digital Low Level RF (LLRF) feedback control.Based on this non-IQ sarnpling method,arbitrary frequency relationship between ADC/DAC sampling clocks and IF signals can be employed.The nonlinearity in digital conversion can be reduced and the system dynamic performance improved.This paper analyzes the nonlinearity in conventional IQ sampling,gives the state variable description of the non-IQ algorithm,presents an implementation and its synchronization,and compares its performances with IQ sampling.

  20. A Self-Powered Hybrid Energy Scavenging System Utilizing RF and Vibration Based Electromagnetic Harvesters

    Science.gov (United States)

    Uluşan, H.; Gharehbaghi, K.; Zorlu, Ö.; Muhtaroğlu, A.; Külah, H.

    2015-12-01

    This study presents a novel hybrid system that combines the power generated simultaneously by a vibration-based Electromagnetic (EM) harvester and a UHF band RF harvester. The novel hybrid scavenger interface uses a power management circuit in 180 nm CMOS technology to step-up and to regulate the combined output. At the first stage of the system, the RF harvester generates positive DC output with a 7-stage threshold compensated rectifier, while the EM harvester generates negative DC output with a self-powered AC/DC negative doubler circuit. At the second stage, the generated voltages are serially added, stepped-up with an on-chip charge pump circuit, and regulated to a typical battery voltage of 3 V. Test results indicate that the hybrid operation enables generation of 9 μW at 3 V output for a wide range of input stimulations, which could not be attained with either harvesting mode by itself. Moreover the hybrid system behaves as a typical battery, and keeps the output voltage stable at 3 V up to 18 μW of output power. The presented system is the first battery-like harvester to our knowledge that generates energy from two independent sources and regulates the output to a stable DC voltage.

  1. A multi-moded rf delay line distribution system for the next linear collider

    Energy Technology Data Exchange (ETDEWEB)

    Tantawi, S.G.; Bowden, G.; Farkas, Z.D.; Irwin, J.; Ko, K.; Kroll, N.; Lavine, T.; Li, Z.; Loewen, R.; Miller, R.; Nantista, C.; Ruth, R.D.; Rifkin, J.; Vlieks, A.E.; Wilson, P.B.; Adolphsen, C.; Wang, J. [Stanford Linear Accelerator Center, SLAC, 2575 Sand Hill Rd, Mento Park, California 94025 (United States)

    1999-07-01

    The Delay Line Distribution System (DLDS) (1) is an alternative to conventional pulse compression which enhances the peak power of an rf source while matching the long pulse of that source to the shorter filling time of the accelerator structure. We present a variation on that scheme that combines the parallel delay lines of the system into one single line. The power of several sources is combined into a single waveguide delay line using a multi-mode launcher. The output mode of the launcher is determined by the phase coding of the input signals. The combined power is extracted using several mode extractors, each of which extracts only one single mode. Hence, the phase coding of the sources controls the output port of the combined power. The power is then fed to the local accelerator structures. We present a detailed design of such a system, including several implementation methods for the launchers, extractors, and ancillary high power rf components. The system is designed so that it can handle the 600 MW peak power required by the NLC design, while maintaining high efficiency. {copyright} {ital 1999 American Institute of Physics.}

  2. Studies on a wideband, solid-state driven RF system for the CERN PS booster

    CERN Document Server

    Paoluzzi, M M; Arnaudon, L; Chritin, N S; Mikulec, B; Hanke, K; Tardy, T

    2012-01-01

    In the framework of the LHC Injectors Upgrade project (LIU) the PS Booster (PSB) will undergo in depth consolidation and upgrade programs [1]. The aim is increasing the extraction energy to 2 GeV, exploiting the potential of Linac4 and allowing reliable operations during the next 25 years. For the RF system, substantial improvements could come from the replacement of the existing narrowband, tuned systems covering the h=1 and h=2 frequency ranges (0.6 ÷ 1.8 MHz and 1.2 ÷ 3.6 MHz respectively) with wideband (0.5 ÷ 4 MHz) Finemet® loaded cavities. The new system would be modular, allow multi-harmonic operation, use solid-state power stages and include fast RF feedback to compensate beam loading effects to some extent. A proof of principle system providing ≈3.0 kV accelerating voltage has been designed, constructed and installed in one of the PSB rings. This paper provides details on the design and measurements as well as information on the project status.

  3. RF and Data Acquisition Systems for Fermilab's ILC SRF Cavity Vertical Test Stand

    Energy Technology Data Exchange (ETDEWEB)

    Joseph P. Ozelis; Roger Nehring; Christiana Grenoble; Thomas J. Powers

    2007-06-01

    Fermilab is developing a facility for vertical testing of SRF cavities as part of a program to improve cavity performance reproducibility for the ILC. The RF system for this facility, using the classic combination of oscillator, phase detector/mixer, and loop amplifier to detect the resonant cavity frequency and lock onto the cavity, is based on the proven production cavity test systems used at Jefferson Lab for CEBAF and SNS cavity testing. The design approach is modular in nature, using commercial-off-the-shelf (COTS) components. This yields a system that can be easily debugged and modified, and with ready availability of spares. Data acquisition and control is provided by a PXI-based hardware platform in conjunction with software developed in the LabView programming environment. This software provides for amplitude and phase adjustment of incident RF power, and measures all relevant cavity power levels, cavity thermal environment parameters, as well as field emission-produced radiation. It also calculates the various cavity performance parameters and their associated errors. Performance during system commissioning and initial cavity tests will be presented.

  4. 5G multimedia massive MIMO communications systems

    OpenAIRE

    Ge, Xiaohu; Wang, Haichao; Zi, Ran; Li, Qiang; Ni, Qiang

    2016-01-01

    In the fifth generation (5G) wireless communication systems, a majority of the traffic demands are contributed by various multimedia applications. To support the future 5G multimedia communication systems, the massive multiple-input multiple-output (MIMO) technique is recognized as a key enabler because of its high spectral efficiency. The massive antennas and radio frequency chains not only improve the implementation cost of 5G wireless communication systems but also result in an intense mut...

  5. NASA ACTS Multibeam Antenna (MBA) System. [Advanced Communications Technology Satellite

    Science.gov (United States)

    Choung, Youn H.; Stiles, W. Herschel; Wu, Joseph; Wong, William C.; Chen, C. Harry

    1986-01-01

    The design of the Advanced Communications Technology Satellite MBA system, which provides both spot beam and scanning beam coverage to both high and low burst rates data-users is examined. The MBA consists of receive and transmit antennas installed on a common precision mounting platform that is integrated to the bus through three flexures; a lightweight system with low thermal distortion is obtained by using composite materials for the MBA structures. The RF design, which is a Cassegrain reflector with a large equivalent focal length/aperture size, is described. Consideration is given to the position of the feed in order to minimize scan loss and sidelobe levels, the size of the subreflector in order to minimize feed spillover, and antenna performance degradation caused by reflector surface distortion. Breadbroad model test result reveal that the maximum sidelobe level outside the 2.5 HPBW region is -30 dB or lower relative to the power.

  6. Communication Systems and Study Method for Active Distribution Power systems

    DEFF Research Database (Denmark)

    Wei, Mu; Chen, Zhe

    Due to the involvement and evolvement of communication technologies in contemporary power systems, the applications of modern communication technologies in distribution power system are becoming increasingly important. In this paper, the International Organization for Standardization (ISO....... The suitability of the communication technology to the distribution power system with active renewable energy based generation units is discussed. Subsequently the typical possible communication systems are studied by simulation. In this paper, a novel method of integrating communication system impact into power...... system simulation is presented to address the problem of lack of off-shelf research tools on the power system communication. The communication system is configured and studied by the OPNET, and the performance of an active distribution power system integrated with the communication system is simulated...

  7. 33 CFR 127.111 - Communications systems.

    Science.gov (United States)

    2010-07-01

    ...) WATERFRONT FACILITIES WATERFRONT FACILITIES HANDLING LIQUEFIED NATURAL GAS AND LIQUEFIED HAZARDOUS GAS Waterfront Facilities Handling Liquefied Natural Gas § 127.111 Communications systems. (a) The...

  8. Complexity-reduced digital predistortion for subcarrier multiplexed radio over fiber systems transmitting sparse multi-band RF signals.

    Science.gov (United States)

    Pei, Yinqing; Xu, Kun; Li, Jianqiang; Zhang, Anxu; Dai, Yitang; Ji, Yuefeng; Lin, Jintong

    2013-02-11

    A novel multi-band digital predistortion (DPD) technique is proposed to linearize the subcarrier multiplexed radio-over-fiber (SCM-RoF) system transmitting sparse multi-band RF signal with large blank spectra between the constituent RF bands. DPD performs on the baseband signal of each individual RF band before up-conversion and RF combination. By disregarding the blank spectra, the processing bandwidth of the proposed DPD technique is greatly reduced, which is only determined by the baseband signal bandwidth of each individual RF band, rather than the entire bandwidth of the combined multi-band RF signal. Experimental demonstration is performed in a directly modulated SCM-RoF system transmitting two 64QAM modulated OFDM signals on 2.4GHz band and 3.6GHz band. Results show that the adjacent channel power (ACP) is suppressed by 15dB leading to significant improvement of the EVM performances of the signals on both of the two bands.

  9. Communications and Intelligent Systems Division Overview

    Science.gov (United States)

    Emerson, Dawn

    2017-01-01

    Provides expertise, and plans, conducts and directs research and engineering development in the competency fields of advanced communications and intelligent systems technologies for applications in current and future aeronautics and space systems.Advances communication systems engineering, development and analysis needed for Glenn Research Center's leadership in communications and intelligent systems technology. Focus areas include advanced high frequency devices, components, and antennas; optical communications, health monitoring and instrumentation; digital signal processing for communications and navigation, and cognitive radios; network architectures, protocols, standards and network-based applications; intelligent controls, dynamics and diagnostics; and smart micro- and nano-sensors and harsh environment electronics. Research and discipline engineering allow for the creation of innovative concepts and designs for aerospace communication systems with reduced size and weight, increased functionality and intelligence. Performs proof-of-concept studies and analyses to assess the impact of the new technologies.

  10. Lumped elements for RF and microwave circuits

    CERN Document Server

    Bahl, Inder

    2003-01-01

    Due to the unprecedented growth in wireless applications over the past decade, development of low-cost solutions for RF and microwave communication systems has become of great importance. This practical new book is the first comprehensive treatment of lumped elements, which are playing a critical role in the development of the circuits that make these cost-effective systems possible. The books offers you an in-depth understanding of the different types of RF and microwave circuit elements, including inductors, capacitors, resistors, transformers, via holes, airbridges, and crossovers. Support

  11. The electromagnetic environment of Magnetic Resonance Imaging systems. Occupational exposure assessment reveals RF harmonics

    Science.gov (United States)

    Gourzoulidis, G.; Karabetsos, E.; Skamnakis, N.; Kappas, C.; Theodorou, K.; Tsougos, I.; Maris, T. G.

    2015-09-01

    Magnetic Resonance Imaging (MRI) systems played a crucial role in the postponement of the former occupational electromagnetic fields (EMF) European Directive (2004/40/EC) and in the formation of the latest exposure limits adopted in the new one (2013/35/EU). Moreover, the complex MRI environment will be finally excluded from the implementation of the new occupational limits, leading to an increased demand for Occupational Health and Safety (OHS) surveillance. The gradient function of MRI systems and the application of the RF excitation frequency result in low and high frequency exposures, respectively. This electromagnetic field exposure, in combination with the increased static magnetic field exposure, makes the MRI environment a unique case of combined EMF exposure. The electromagnetic field levels in close proximity of different MRI systems have been assessed at various frequencies. Quality Assurance (QA) & safety issues were also faced. Preliminary results show initial compliance with the forthcoming limits in each different frequency band, but also revealed peculiar RF harmonic components, of no safety concern, to the whole range detected (20-1000MHz). Further work is needed in order to clarify their origin and characteristics.

  12. The drive beam pulse compression system for the CLIC RF power source

    CERN Document Server

    Corsini, R

    1999-01-01

    The Compact LInear Collider (CLIC) is a high energy (0.5 to 5 TeV) e ± linear collider that uses a high- current electron beam (the drive beam) for 30 GHz RF power production by the Two-Beam Acceleration (TBA) method. Recently, a new cost­effective and efficient generation scheme for the drive beam has been developed. A fully­loaded normal­conducting linac operating at lower frequency (937 MHz) generates and accelerates the drive beam bunches, and a compression system composed of a delay­line and two combiner rings produces the proper drive beam time structure for RF power generation in the drive beam decelerator. In this paper, a preliminary design of the whole compression system is presented. In particular, the fundamental issue of preserving the bunch quality along the complex is studied and its impact on the beam parameters and on the various system components is assessed. A first design of the rings and delay­line lattice, including path length tuning chicanes, injection and extraction regions is a...

  13. Ultracold Rubidium and Potassium System for Atom Chip-based Microwave and RF Potentials

    Science.gov (United States)

    Ziltz, Austin R.

    In this dissertation we study the development of microwave and RF near-field potentials for use with atom chip trapped atomic gases. These potentials are inherently spin-dependent, able to target individual spin states simultaneously. In contrast with traditional atom chip potentials, these RF traps can be operated at arbitrary bias magnetic field strengths and thus be combined with magnetic Feshbach resonances. Furthermore, these potentials can strongly suppress the potential roughness that plagues traditional atom chip potentials. We present a dual chamber atom chip apparatus for generating ultracold 87Rb and 39K atomic gases. The apparatus produces quasi-pure Bose-Einstein condensates of 104 87Rb atoms in an atom chip trap that features a dimple and good optical access. We have also demonstrated production of ultracold 39K and subsequent loading into the chip trap. We describe the details of the dual chamber vacuum system, the cooling lasers, the magnetic trap, the multi coil magnetic transport system, and the atom chip. The apparatus is well suited for studies of atom-surface forces, quantum pumping and transport experiments, atom interferometry, novel chip-based traps, and studies of one-dimensional many-body systems.

  14. Acoustic Communications Measurement Systems (ACOMMS)

    Data.gov (United States)

    Federal Laboratory Consortium — FUNCTION: Design and develop adaptive signal processing techniques to improve underwater acoustic communications and networking. Phase coherent and incoherent signal...

  15. How do communication systems emerge?

    Science.gov (United States)

    Scott-Phillips, Thomas C; Blythe, Richard A; Gardner, Andy; West, Stuart A

    2012-05-22

    Communication involves a pair of behaviours--a signal and a response--that are functionally interdependent. Consequently, the emergence of communication involves a chicken-and-egg problem: if signals and responses are dependent on one another, then how does such a relationship emerge in the first place? The empirical literature suggests two solutions to this problem: ritualization and sensory manipulation; and instances of ritualization appear to be more common. However, it is not clear from a theoretical perspective why this should be the case, nor if there are any other routes to communication. Here, we develop an analytical model to examine how communication can emerge. We show that: (i) a state of non-interaction is evolutionarily stable, and so communication will not necessarily emerge even when it is in both parties' interest; (ii) the conditions for sensory manipulation are more stringent than for ritualization, and hence ritualization is likely to be more common; and (iii) communication can arise by a third route, when the intention to communicate can itself be communicated, but this may be limited to humans. More generally, our results demonstrate the utility of a functional approach to communication.

  16. Computational Interpersonal Communication: Communication Studies and Spoken Dialogue Systems

    Directory of Open Access Journals (Sweden)

    David J. Gunkel

    2016-09-01

    Full Text Available With the advent of spoken dialogue systems (SDS, communication can no longer be considered a human-to-human transaction. It now involves machines. These mechanisms are not just a medium through which human messages pass, but now occupy the position of the other in social interactions. But the development of robust and efficient conversational agents is not just an engineering challenge. It also depends on research in human conversational behavior. It is the thesis of this paper that communication studies is best situated to respond to this need. The paper argues: 1 that research in communication can supply the information necessary to respond to and resolve many of the open problems in SDS engineering, and 2 that the development of SDS applications can provide the discipline of communication with unique opportunities to test extant theory and verify experimental results. We call this new area of interdisciplinary collaboration “computational interpersonal communication” (CIC

  17. Intelligent Platform Management Controller for Low Level RF Control System ATCA Carrier Board

    CERN Document Server

    Predki, Pawel

    2011-01-01

    High availability and reliability are among the most desirable features of control systems in modern High-Energy Physics (HEP) and other big-scale scientific experiments. One of the recent developments that has influenced this field was the emergence of the Advanced Telecommunications Computing Architecture (ATCA). Designed for the telecommunications industry it has been successfully applied in other domains such as accelerator control systems. A good example is the application of ATCA stan- dard for the design of Low Level RF (LLRF) control system for the X-Ray Free Electron Laser (XFEL) being developed in Deutsches Elektronen Synchrotron (DESY). Reliability and availability requirements for such a device play a crucial role among other parameters. Thus, the ATCA standard, with five- nines availability, is considered one of the best candidates for this system. This article focuses on the central management unit of every ATCA board, namely the Intelligent Platform Management Controller (IPMC), developed for t...

  18. Implementation of wireless power transfer and communications for an implantable ocular drug delivery system.

    Science.gov (United States)

    Tang, T B; Smith, S; Flynn, B W; Stevenson, J T M; Gundlach, A M; Reekie, H M; Murray, A F; Renshaw, D; Dhillon, B; Ohtori, A; Inoue, Y; Terry, J G; Walton, A J

    2008-09-01

    A wireless power transfer and communication system based on near-field inductive coupling has been designed and implemented. The feasibility of using such a system to remotely control drug release from an implantable drug delivery system is addressed. The architecture of the wireless system is described and the signal attenuation over distance in both water and phosphate buffered saline is studied. Additionally, the health risk due to exposure to radio frequency (RF) radiation is examined using a biological model. The experimental results demonstrate that the system can trigger the release of drug within 5 s, and that such short exposure to RF radiation does not produce any significant (system could replace a chemical battery in an implantable system, eliminating the risks associated with battery failure and leakage and also allowing more compact designs for applications such as drug delivery.

  19. ALS Booster Ring RF System Upgrade for Top-Off Mode of Operation

    CERN Document Server

    Kwiatkowski, Slawomir

    2005-01-01

    ALS is one of the first third generation synchrotron light sources which has been operating since 1993 at Berkeley Lab. In the present ALS operation scenario 1.5GeV electron beam is injected from the booster into the storage ring every 8 hours where is accelerated to the final energy of 1.9GeV. The beam decays between fills from 400mA to 200mA with the time average current of 250mA. In order to increase the beam brighthess ALS team plans to increase the beam current to 500mA and maintain it constant during machine operation ("Top-Off" mode of operation). This operation scenario will require full energy injection from the booster ring into the storage ring and constant operation of the injector (10 bunches with the total charge of 1nC every 30 to 35 seconds). In this paper we will present the results of the ALS injector RF system analysis fo Top-Off mode of operation and describe the way we intent to implement the necessary modifications to the booster RF system.

  20. IL-1β and IL-6 Are Highly Expressed in RF+IgE+ Systemic Lupus Erythematous Subtype

    Science.gov (United States)

    Zhang, Junlong; Shen, Beilei; Huang, Zhuochun; Tan, Chunyu; Baan, Carla C.

    2017-01-01

    Background. Systemic lupus erythematosus (SLE) is an autoimmune disease with great heterogeneity in pathogenesis and clinical symptoms. Rheumatoid factor (RF) is one key indicator for rheumatoid arthritis (RA) while immunoglobulin E (IgE) is associated with type I hypersensitivity. To better categorize SLE subtypes, we determined the dominant cytokines based on familial SLE patients. Methods. RF, IgE, and multiple cytokines (i.e., IL-1β, IL-6, IL-8, IL-10, IL-17, IFN-γ, IP-10, MCP-1, and MIP-1β) were measured in sera of familial SLE patients (n = 3), noninherited SLE patients (n = 108), and healthy controls (n = 80). Results. Three familial SLE patients and 5 noninherited SLE cases are with features of RF+IgE+. These RF+IgE+ SLE patients expressed significantly higher levels of IL-1β and IL-6 than the other SLE patients (P < 0.05). IL-6 correlated with both IgE and IL-1β levels in RF+IgE+ SLE patients (r2 = 0.583, P = 0.027; r2 = 0.847, P = 0.001), and IgE also correlated with IL-1β (r2 = 0.567, P = 0.031). Conclusion. Both IL-1β and IL-6 are highly expressed cytokines in RF+IgE+ SLE subtype which may be related to the pathogenesis of this special SLE subtype and provide accurate treatment strategy by neutralizing IL-1β and IL-6. PMID:28286780

  1. Phase-Modulated Optical Communication Systems

    CERN Document Server

    Ho, Keang-Po

    2005-01-01

    Fiber-optic communication systems have revolutionized our telecommunication infrastructures – currently, almost all telephone land-line, cellular, and internet communications must travel via some form of optical fibers. In these transmission systems, neither the phase nor frequency of the optical signal carries information – only the intensity of the signal is used. To transmit more information in a single optical carrier, the phase of the optical carrier must be explored. As a result, there is renewed interest in phase-modulated optical communications, mainly in direct-detection DPSK signals for long-haul optical communication systems. When optical amplifiers are used to maintain certain signal level among the fiber link, the system is limited by amplifier noises and fiber nonlinearities. Phase-Modulated Optical Communication Systems surveys this newly popular area, covering the following topics: The transmitter and receiver for phase-modulated coherent lightwave systems Method for performance analysis o...

  2. Systems and Methods for Radar Data Communication

    Science.gov (United States)

    Bunch, Brian (Inventor); Szeto, Roland (Inventor); Miller, Brad (Inventor)

    2013-01-01

    A radar information processing system is operable to process high bandwidth radar information received from a radar system into low bandwidth radar information that may be communicated to a low bandwidth connection coupled to an electronic flight bag (EFB). An exemplary embodiment receives radar information from a radar system, the radar information communicated from the radar system at a first bandwidth; processes the received radar information into processed radar information, the processed radar information configured for communication over a connection operable at a second bandwidth, the second bandwidth lower than the first bandwidth; and communicates the radar information from a radar system, the radar information communicated from the radar system at a first bandwidth.

  3. A novel optically transparent RF shielding for fully integrated PET/MRI systems.

    Science.gov (United States)

    Parl, C; Kolb, A; Schmid, A M; Wehrl, H F; Disselhorst, J A; Soubiran, P D; Stricker-Shaver, D; Pichler, B J

    2017-09-01

    Preclinical imaging benefits from simultaneous acquisition of high-resolution anatomical and molecular data. Additionally, PET/MRI systems can provide functional PET and functional MRI data. To optimize PET sensitivity, we propose a system design that fully integrates the MRI coil into the PET system. This allows positioning the scintillators near the object but requires an optimized design of the MRI coil and PET detector. It further requires a new approach in realizing the radiofrequency (RF) shielding. Thus, we propose the use of an optically transparent RF shielding material between the PET scintillator and the light sensor, suppressing the interference between both systems. We evaluated two conductive foils (ITO, 9900) and a wire mesh. The PET performance was tested on a dual-layer scintillator consisting of 12  ×  12 LSO matrices, shifted by half a pitch. The pixel size was 0.9  ×  0.9 mm(2); the lengths were 10.0 mm and 5.0 mm, respectively. For a light sensor, we used a 4  ×  4 SiPM array. The RF attenuation was measured from 320 kHz to 420 MHz using two pick-up coils. MRI-compatibility and shielding effect of the materials were evaluated with an MRI system. The average FWHM energy resolution at 511 keV of all 144 crystals of the layer next to the SiPM was deteriorated from 15.73  ±  0.24% to 16.32  ±  0.13%, 16.60  ±  0.25%, and 19.16  ±  0.21% by the ITO foil, 9900 foil, mesh material, respectively. The average peak-to-valley ratio of the PET detector changed from 5.77  ±  0.29 to 4.50  ±  0.39, 4.78  ±  0.48, 3.62  ±  0.16, respectively. The ITO, 9900, mesh attenuated the scintillation light by 11.3  ±  1.6%, 11.0  ±  1.8%, 54.3  ±  0.4%, respectively. To attenuate the RF from 20 MHz to 200 MHz, mesh performed better than copper. The results show that an RF shielding material that is sufficiently transparent for

  4. A novel optically transparent RF shielding for fully integrated PET/MRI systems

    Science.gov (United States)

    Parl, C.; Kolb, A.; Schmid, A. M.; Wehrl, H. F.; Disselhorst, J. A.; Soubiran, P. D.; Stricker-Shaver, D.; Pichler, B. J.

    2017-09-01

    Preclinical imaging benefits from simultaneous acquisition of high-resolution anatomical and molecular data. Additionally, PET/MRI systems can provide functional PET and functional MRI data. To optimize PET sensitivity, we propose a system design that fully integrates the MRI coil into the PET system. This allows positioning the scintillators near the object but requires an optimized design of the MRI coil and PET detector. It further requires a new approach in realizing the radiofrequency (RF) shielding. Thus, we propose the use of an optically transparent RF shielding material between the PET scintillator and the light sensor, suppressing the interference between both systems. We evaluated two conductive foils (ITO, 9900) and a wire mesh. The PET performance was tested on a dual-layer scintillator consisting of 12  ×  12 LSO matrices, shifted by half a pitch. The pixel size was 0.9  ×  0.9 mm2 the lengths were 10.0 mm and 5.0 mm, respectively. For a light sensor, we used a 4  ×  4 SiPM array. The RF attenuation was measured from 320 kHz to 420 MHz using two pick-up coils. MRI-compatibility and shielding effect of the materials were evaluated with an MRI system. The average FWHM energy resolution at 511 keV of all 144 crystals of the layer next to the SiPM was deteriorated from 15.73  ±  0.24% to 16.32  ±  0.13%, 16.60  ±  0.25%, and 19.16  ±  0.21% by the ITO foil, 9900 foil, mesh material, respectively. The average peak-to-valley ratio of the PET detector changed from 5.77  ±  0.29 to 4.50  ±  0.39, 4.78  ±  0.48, 3.62  ±  0.16, respectively. The ITO, 9900, mesh attenuated the scintillation light by 11.3  ±  1.6%, 11.0  ±  1.8%, 54.3  ±  0.4%, respectively. To attenuate the RF from 20 MHz to 200 MHz, mesh performed better than copper. The results show that an RF shielding material that is sufficiently transparent for

  5. Unified Approach to Modeling and Simulation of Space Communication Networks and Systems

    Science.gov (United States)

    Barritt, Brian; Bhasin, Kul; Eddy, Wesley; Matthews, Seth

    2010-01-01

    Network simulator software tools are often used to model the behaviors and interactions of applications, protocols, packets, and data links in terrestrial communication networks. Other software tools that model the physics, orbital dynamics, and RF characteristics of space systems have matured to allow for rapid, detailed analysis of space communication links. However, the absence of a unified toolset that integrates the two modeling approaches has encumbered the systems engineers tasked with the design, architecture, and analysis of complex space communication networks and systems. This paper presents the unified approach and describes the motivation, challenges, and our solution - the customization of the network simulator to integrate with astronautical analysis software tools for high-fidelity end-to-end simulation. Keywords space; communication; systems; networking; simulation; modeling; QualNet; STK; integration; space networks

  6. White House Communications Agency (WHCA) Presidential Voice Communications Rack Mount System Mechanical Drawing Package

    Science.gov (United States)

    2015-12-01

    Harris , 117G, communications, White House Communications Agency 16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF ABSTRACT UU 18...used by WHCA. The customer desired to upgrade their comms equipment from Harris 117F radios to 117G radios. These radios offer a smaller package with...rack unit (9U) chassis that did not use a fiber optic modem and instead used direct radio frequency (RF) output from the Harris 117F radio. The

  7. Phase Noise Influence in Optical OFDM Systems employing RF Pilot Tone for Phase Noise Cancellation

    Science.gov (United States)

    Jacobsen, Gunnar; Kazovsky, Leonid G.; Xu, Tianhua; Popov, Sergei; Li, Jie; Zhang, Yima; Friberg, Ari T.

    2011-06-01

    For coherent and direct-detection Orthogonal Frequency Division Multiplexed (OFDM) systems employing radio frequency (RF) pilot tone phase noise cancellation the influence of laser phase noise is evaluated. Novel analytical results for the common phase error and for the (modulation dependent) inter carrier interference are evaluated based upon Gaussian statistics for the laser phase noise. In the evaluation it is accounted for that the laser phase noise is filtered in the correlation signal detection. Numerical results are presented for OFDM systems with 4 and 16 PSK modulation, 200 OFDM bins and baud rate of 1 GS/s. It is found that about 225 km transmission is feasible for the coherent 4PSK-OFDM system over normal (G.652) fiber.

  8. Stable High-T {sub c} rf SQUID NDE system operating in noisy environment

    Energy Technology Data Exchange (ETDEWEB)

    He, D.F. [Superconducting Materials Center, National Institute for Materials Science, Sengen 1-2-1, Tsukuba, Ibaraki 305-0047 (Japan)]. E-mail: he.dongfeng@nims.go.jp; Yoshizawa, M. [Iwate University, Ueda 4-3-5, Morioka 020-8551 (Japan); Itozaki, H. [Superconducting Materials Center, National Institute for Materials Science, Sengen 1-2-1, Tsukuba, Ibaraki 305-0047 (Japan)

    2006-04-15

    A high-T {sub c} rf SQUID NDE system was developed for stable, long time operation in a noisy environment. To reduce the influence of high frequency electromagnetic interference (EMI), a carefully designed metal shielding made of 0.1 mm thick metal foil was used. With the metal shielding, the SQUID could still operate well when a cellular phone was used nearby although the cellular phone could produce very strong EMI noises. To reduce the influence of the line interference or low frequency noises, a compensation method was used in the SQUID-based NDE system. With the compensation, the low frequency and the line interference could be reduced well. Using this SQUID-based NDE system, we successfully performed the NDE measurements in a noisy environment.

  9. Phase Noise Influence in Optical OFDM Systems employing RF Pilot Tone for Phase Noise Cancellation

    CERN Document Server

    Jacobsen, Gunnar; Xu, Tianhua; Popov, Sergei; Li, Jie; Zhang, Yimo; Friberg, Ari T

    2016-01-01

    For coherent and direct-detection Orthogonal Frequency Division Multiplexed (OFDM) systems employing radio frequency (RF) pilot tone phase noise cancellation the influence of laser phase noise is evaluated. Novel analytical results for the common phase error and for the (modulation dependent) inter carrier interference are evaluated based upon Gaussian statistics for the laser phase noise. In the evaluation it is accounted for that the laser phase noise is filtered in the correlation signal detection. Numerical results are presented for OFDM systems with 4 and 16 PSK modulation, 200 OFDM bins and baud rate of 1 GS/s. It is found that about 225 km transmission is feasible for the coherent 4PSK-OFDM system over normal (G.652) fiber.

  10. Portable RF-Sensor System for the Monitoring of Air Pollution and Water Contamination

    Directory of Open Access Journals (Sweden)

    Joonhee Kang

    2012-01-01

    Full Text Available Monitoring air pollution including the contents of VOC, O3, NO2, and dusts has attracted a lot of interest in addition to the monitoring of water contamination because it affects directly to the quality of living conditions. Most of the current air pollution monitoring stations use the expensive and bulky instruments and are only installed in the very limited area. To bring the information of the air and water quality to the public in real time, it is important to construct portable monitoring systems and distribute them close to our everyday living places. In this work, we have constructed a low-cost portable RF sensor system by using 400 MHz transceiver to achieve this goal. Accuracy of the measurement was comparable to the ones used in the expensive and bulky commercial air pollution forecast systems.

  11. Synchronization Techniques for Chaotic Communication Systems

    CERN Document Server

    Jovic, Branislav

    2011-01-01

    Since the early 1990s, when synchronization of chaotic communication systems became a popular research subject, a vast number of scientific papers have been published. However, most of today's books on chaotic communication systems deal exclusively with the systems where perfect synchronization is assumed, an assumption which separates theoretical from practical, real world, systems. This book is the first of its kind dealing exclusively with the synchronization techniques for chaotic communication systems. It describes a number of novel robust synchronization techniques, which there is a lack

  12. Development of simple designs of multitip probe diagnostic systems for RF plasma characterization.

    Science.gov (United States)

    Naz, M Y; Shukrullah, S; Ghaffar, A; Rehman, N U

    2014-01-01

    Multitip probes are very useful diagnostics for analyzing and controlling the physical phenomena occurring in low temperature discharge plasmas. However, DC biased probes often fail to perform well in processing plasmas. The objective of the work was to deduce simple designs of DC biased multitip probes for parametric study of radio frequency plasmas. For this purpose, symmetric double probe, asymmetric double probe, and symmetric triple probe diagnostic systems and their driving circuits were designed and tested in an inductively coupled plasma (ICP) generated by a 13.56 MHz radio frequency (RF) source. Using I-V characteristics of these probes, electron temperature, electron number density, and ion saturation current was measured as a function of input power and filling gas pressure. An increasing trend was noticed in electron temperature and electron number density for increasing input RF power whilst a decreasing trend was evident in these parameters when measured against filling gas pressure. In addition, the electron energy probability function (EEPF) was also studied by using an asymmetric double probe. These studies confirmed the non-Maxwellian nature of the EEPF and the presence of two groups of the energetic electrons at low filling gas pressures.

  13. Development of Simple Designs of Multitip Probe Diagnostic Systems for RF Plasma Characterization

    Directory of Open Access Journals (Sweden)

    M. Y. Naz

    2014-01-01

    Full Text Available Multitip probes are very useful diagnostics for analyzing and controlling the physical phenomena occurring in low temperature discharge plasmas. However, DC biased probes often fail to perform well in processing plasmas. The objective of the work was to deduce simple designs of DC biased multitip probes for parametric study of radio frequency plasmas. For this purpose, symmetric double probe, asymmetric double probe, and symmetric triple probe diagnostic systems and their driving circuits were designed and tested in an inductively coupled plasma (ICP generated by a 13.56 MHz radio frequency (RF source. Using I-V characteristics of these probes, electron temperature, electron number density, and ion saturation current was measured as a function of input power and filling gas pressure. An increasing trend was noticed in electron temperature and electron number density for increasing input RF power whilst a decreasing trend was evident in these parameters when measured against filling gas pressure. In addition, the electron energy probability function (EEPF was also studied by using an asymmetric double probe. These studies confirmed the non-Maxwellian nature of the EEPF and the presence of two groups of the energetic electrons at low filling gas pressures.

  14. RF Performance of Layer-Structured Broadband Passive Millimeter-Wave Imaging System

    Directory of Open Access Journals (Sweden)

    Kunio Sakakibara

    2016-01-01

    Full Text Available Low profile and simple configuration are advantageous for RF module in passive millimeter-wave imaging system. High sensitivity over broad operation bandwidth is also necessary to detect right information from weak signal. We propose a broadband layer-structured module with low profile, simple structure, and ease of manufacture. This module is composed of a lens antenna and a detector module that consists of a detector circuit and a broadband microstrip-to-waveguide transition. The module forms a layer structure as a printed substrate with detector circuit is fixed between two metal plates with horn antennas and back-short waveguides. We developed a broadband passive millimeter-wave imaging module composed of a lens antenna and a detector module in this work. The gain and the antenna efficiency were measured, and the broadband operation was observed for the lens antenna. For the detector module, peak sensitivity was 8100 V/W. Furthermore, the detector module recognized a difference in the absorber’s temperature. The designs of the lens antenna and the detector module are presented and the RF performances of these components are reported. Finally, passive millimeter-wave imaging of a car, a human, and a metal plate in clothes is demonstrated in this paper.

  15. RF Plasma Torch System for Metal Matrix Composite Production in Nuclear Fuel Cladding

    Science.gov (United States)

    Holik, Eddie, III

    2007-10-01

    For the first time in 30 years, plans are afoot to build new fission power plants in the US. It is timely to develop technology that could improve the safety and efficiency of new reactors. A program of development for advanced fuel cycles and Generation IV reactors is underway. The path to greater efficiency is to increase the core operating temperature. That places particular challenges to the cladding tubes that contain the fission fuel. A promising material for this purpose is a metal matrix composite (MMC) in which ceramic fibers are bonded within a high-strength steel matrix, much like fiberglass. Current MMC technology lacks the ability to effectively bond traditional high-temperature alloys to ceramic strands. The purpose of this project is to design an rf plasma torch system to use titanium as a buffer between the ceramic fibers and the refractory outer material. The design and methods of using an rf plasma torch to produce a non-equilibrium phase reaction to bond together the MMC will be discussed. The effects of having a long lived fuel cladding in the design of future reactors will also be discussed.

  16. The RF-System of the New Gsi High Current Linac Hsi

    CERN Document Server

    Hutter, G; Hartmann, W; Kube, G; Pilz, M; Vinzenz, W

    2000-01-01

    The RF part of the new high current injector-linac HSI consists of five cavities with the new operating frequency of 36 MHz instead of 27 MHz of the removed Wideroe type injector. The calculated power requirements of the cavities including beam load in three structures were between 110 kW for a rebuncher and 1.75 MW pulse-power for the two IH-cavities. The beam load is up to 150 kW for the RFQ and up to 750 kW for the two drift tube tanks. An additional 36 MHz debuncher in the transfer line to the Synchrotron (SIS) will need 120 kW pulse power. We decided to fulfil these demands with amplifiers of only two power classes, namely three amplifiers with 2 MW and six amplifiers with 200 kW pulse output power. The latter ones are also used as drivers for the 2 MW stages. The 200 kW amplifiers were specified in detail by GSI and ordered in the industry. The three 2 MW final amplifiers were designed, constructed and built by GSI. The paper gives an overview of the complete RF system and the operating performance of a...

  17. Performance of the arc detectors of LHC high power RF system

    CERN Document Server

    Valuch, D; Brunner, O

    2011-01-01

    During operation, the LHC high power RF equipment, such as klystrons, circulators, waveguides and couplers have to be protected from damage caused by electromagnetic discharges. Once ignited these arcs grow over the full height of the waveguide and travel towards the RF source. The burning plasma can cause serious damage to the metal surfaces or ferrite materials. The LHC arc detector system is based on the optical detection of the discharge through small apertures in the waveguide walls. The light is guided by means of an opti-cal fibre from the viewing port to a photo diode. Experience shows that some of the currently used optical fibres suffer from x-ray induced opacity. The sensors are also exposed to the radiation produced by secondary showers coming from the high intensity beams which, if not treated properly, can cause frequent spurious trips. In the second half of the paper we present a number of improvements to the design, measurements with optical parameters from real arcs and a fibre-less version o...

  18. COMMUNICATION AND INFORMATION SYSTEM MANAGEMENT INTERNATIONAL

    Directory of Open Access Journals (Sweden)

    Mircea Alexandru Răduţeanu

    2012-01-01

    Full Text Available In recent decades international management itself as a separate component of the general science of leadership, is an intercultural management. In this context of globalization, computerization, any business that wants have a modern management should have a structured information system based on communication, overall objective consisting in providing accurate data in real time all parties, increasing the level of communication. Given these considerations, we conducted this work trying to highlight the role of communication in achieving a modern, emphasizing international management features.The paper is divided into 6 parts, prefaced by an introduction of the paper we presented and completed within a set of conclusions on the effectiveness of communication. During the other paragraphs, we present the theoretical concepts of international management, communication, after which I stressed the role of information communication, managerial communication and will then focus on the process, taking stock of its specific stages in international management.

  19. Communication for command and control systems

    CERN Document Server

    Morris, D J

    1983-01-01

    Communication for Command and Control Systems provides a thorough exposition of the basic theoretical and practical features involved in the design of communication networks for command and control systems. This book focuses primarily on the practical side of computer-controlled communication. This text concentrates on the communication sides of the subject by surveying the means of transferring data between the various processing points and by appraising their potential advantages and possible defects in implementation. In this respect, this book should prove useful for the practicing enginee

  20. X-band RF power sources for accelerator applications

    Energy Technology Data Exchange (ETDEWEB)

    Kirshner, Mark F.; Kowalczyk, Richard D.; Wilsen, Craig B.; True, Richard B.; Simpson, Ian T.; Wray, John T., E-mail: mark.kirshner@L-3com.com [L-3 Communications Electron Devices, San Carlos, CA (United States)

    2011-07-01

    The majority of medical and industrial linear accelerators (LINACs) in use today operate at S-band. To reduce size and weight, these systems are gradually migrating toward X-band. The new LINACs will require suitable RF components to power them. In anticipation of this market, L-3 Communications Electron Devices Division (EDD) has recently developed a suite of RF sources operating at 9.3 GHz to complement our existing S-band product line. (author)

  1. Reconfigurable/Reprogrammable Communications Systems Project

    Data.gov (United States)

    National Aeronautics and Space Administration — NASA's latest effort in developing a common platform for space communication and navigation systems is the Space Telecommunications Radio System (STRS) standard. It...

  2. Functional and Expression Analysis of the Metal-Inducible dmeRF System from Rhizobium leguminosarum bv. viciae

    Science.gov (United States)

    Rubio-Sanz, L.; Prieto, R. I.; Imperial, J.; Brito, B.

    2013-01-01

    A gene encoding a homolog to the cation diffusion facilitator protein DmeF from Cupriavidus metallidurans has been identified in the genome of Rhizobium leguminosarum UPM791. The R. leguminosarum dmeF gene is located downstream of an open reading frame (designated dmeR) encoding a protein homologous to the nickel- and cobalt-responsive transcriptional regulator RcnR from Escherichia coli. Analysis of gene expression showed that the R. leguminosarum dmeRF genes are organized as a transcriptional unit whose expression is strongly induced by nickel and cobalt ions, likely by alleviating the repressor activity of DmeR on dmeRF transcription. An R. leguminosarum dmeRF mutant strain displayed increased sensitivity to Co(II) and Ni(II), whereas no alterations of its resistance to Cd(II), Cu(II), or Zn(II) were observed. A decrease of symbiotic performance was observed when pea plants inoculated with an R. leguminosarum dmeRF deletion mutant strain were grown in the presence of high concentrations of nickel and cobalt. The same mutant induced significantly lower activity levels of NiFe hydrogenase in microaerobic cultures. These results indicate that the R. leguminosarum DmeRF system is a metal-responsive efflux mechanism acting as a key element for metal homeostasis in R. leguminosarum under free-living and symbiotic conditions. The presence of similar dmeRF gene clusters in other Rhizobiaceae suggests that the dmeRF system is a conserved mechanism for metal tolerance in legume endosymbiotic bacteria. PMID:23934501

  3. Economics of satellite communications systems

    Science.gov (United States)

    Pritchard, Wilbur L.

    This paper is partly a tutorial, telling systematically how one goes about calculating the total annual costs of a satellite communications system, and partly the expression of some original ideas on the choice of parameters so as to minimize these costs. The calculation of costs can be divided into two broad categories. The first is technical and is concerned with estimating what particular equipment will cost and what will be the annual expense to maintain and operate it. One starts in the estimation of any new system by listing the principal items of equipment, such as satellites, earth stations of various sizes and functions, telemetry and tracking equipment and terrestrial interfaces, and then estimating how much each item will cost. Methods are presented for generating such estimates, based on a knowledge of the gross parameters, such as antenna size, coverage area, transmitter power and information rate. These parameters determine the system performance and it is usually possible, knowing them, to estimate the costs of the equipment rather well. Some formulae based on regression analyses are presented. Methods are then given for estimating closely related expenses, such as maintenance and operation, and then an approximate method is developed for estimating terrestrial interconnection costs. It is pointed out that in specific cases when tariff and geographical information are available, it is usually better to work with specific data, but nonetheless it is often desirable, especially in global system estimating, to approximate these interconnect costs without recourse to individual tariffs. The procedure results in a set of costs for the purchase of equipment and its maintenance, and a schedule of payments. Some payments will be incurred during the manufacture of the satellite and before any systems operation, but many will not be incurred until the system is no longer in use, e.g. incentives. In any case, with the methods presented in the first section, one

  4. Low-Level RF Control of Spallation Neutron Source: System and Characterization

    Energy Technology Data Exchange (ETDEWEB)

    Ma, Hengjie [ORNL

    2005-01-01

    The low-level RF control system currently commissioned throughout the Spallation Neutron Source (SNS) LINAC evolved from three design iterations over one year intensive research and development. Its digital hardware implementation is efficient, and has succeeded in achieving a minimum latency of less than 150 ns which is the key for accomplishing an all digital feedback control for the full bandwidth. The control bandwidth is analyzed in frequency domain and characterized by testing its transient response. The hardware implementation also includes the provision of a time-shared input channel for a superior phase differential measurement between the cavity field and the reference. A companion co-simulation system for the digital hardware was developed to ensure a reliable long-term supportability. A large effort has also been made in the operation software development for the practical issues such as the process automations, cavity filling, beam loading compensation, and the cavity mechanical resonance suppression.

  5. Experimental millimeter-wave satellite communications system

    Science.gov (United States)

    Suzuki, Yoshiaki; Shimada, Masaaki; Arimoto, Yoshinori; Shiomi, Tadashi; Kitazume, Susumu

    This paper describes an experimental system of millimeter-wave satellite communications via Japan's Engineering Test Satellite-VI (ETS-VI) and a plan of experiments. Two experimental missions are planned using ETS-VI millimeter-wave (43/38 GHz bands) transponder, considering the millimeter-wave characteristics such as large transmission capacity and possibility to construct a small earth station with a high gain antenna. They are a personal communication system and an inter-satellite communication system. Experimental system including the configuration and the fundamental functions of the onboard transponder and the outline of the experiments are presented.

  6. RF FPGA for 0.4 to 18 GHz DoD Multi-function Systems

    Science.gov (United States)

    2013-03-01

    Extremely low loss, high isolation RF switches using phase change materials ( PCM ). Multiport RF switch designs that optimize thermal design to...improve PCM performance, and integrate arrays of these switches on thermally and electrically optimized substrates.  Multiport switch designs...with low simulated RF losses of 0.1 - 0.2 dB up to 20 GHz and have 35dB - 60dB isolation between ports, based on measured and extrapolated PCM data

  7. Passive and active RF-microwave circuits course and exercises with solutions

    CERN Document Server

    Jarry, Pierre

    2015-01-01

    Microwave and radiofrequency (RF) circuits play an important role in communication systems. Due to the proliferation of radar, satellite, and mobile wireless systems, there is a need for design methods that can satisfy the ever increasing demand for accuracy, reliability, and fast development times. This book explores the principal elements for receiving and emitting signals between Earth stations, satellites, and RF (mobile phones) in four parts; the theory and realization of couplers, computation and realization of microwave and RF filters, amplifiers and microwave and RF oscillators. Pas

  8. How to Bootstrap a Human Communication System

    Science.gov (United States)

    Fay, Nicolas; Arbib, Michael; Garrod, Simon

    2013-01-01

    How might a human communication system be bootstrapped in the absence of conventional language? We argue that motivated signs play an important role (i.e., signs that are linked to meaning by structural resemblance or by natural association). An experimental study is then reported in which participants try to communicate a range of pre-specified…

  9. In Search of a System For Communication.

    Science.gov (United States)

    Remirez, Richard J. F.

    A research project sponsored by Wofford College was launched in the summer of 1974 in Spartanburg, South Carolina, to develop a system of communication by which hospital personnel working in an emergency room could communicate with patients who speak a language other than English. The project followed a year-long research effort of previous work…

  10. Nonoral Communication System Project: 1964-1973.

    Science.gov (United States)

    Vicker, Beverly A., Ed.

    Five papers comprising the monograph describe a nonoral communication program which evolved from the clinical experiences of speech pathologists and physical therapists with severely dysarthric, physically handicapped children in a hospital school. Explicated are such aspects of nonoral communication as oral speech dysfunction systems of nonoral…

  11. Simulating Rain Fade In A Communication System

    Science.gov (United States)

    Shalkhauser, Kurt A.; Nagy, Lawrence A.; Svoboda, James K.

    1994-01-01

    Automated, computer-controlled assembly of electronic equipment developed for use in simulation testing of downlink portion of Earth/satellite microwave digital communication system. Designed to show effects upon performance of system of rain-induced fading in received signal and increases in transmitted power meant to compensate for rain-induced fading. Design of communication system improved iteratively in response to results of simulations, leading eventually to design ensuring clear, uninterrupted transmission of digital signals.

  12. Transceiver and system design for digital communications

    CERN Document Server

    Bullock, Scott R

    2014-01-01

    This is the fourth edition of this successful professional reference book on transceiver design, the device that both sends and receives signals, and its place within the wireless communication system. It gives engineers and others a good intuitive understanding of wireless systems and spread spectrum. New topics covered include cognitive radio, systems, networks, and commercial communications. In addition, many items have been extensively updated to improve the flow of the book and enhance comprehension.

  13. Design of a mechanically actuated RF grounding system for the ITER ICRH antenna

    CERN Document Server

    Hancock, D; Beaumont, B; Dumortier, P; Durodie, F; Kyrytsya, V; Louche, F; McKinley, R; Nicholls, K

    2013-01-01

    In the ITER equatorial ports containing ICRH antennas, parasitic electrical resonances can be excited in the nominal 20 mm clearance gap between the port walls and the plug contained within it. RF calculations have established that these resonances can be effectively mitigated by a series of suitably located electrically conducting contacts between the port and plug. These contacts must allow installation and removal of the antenna but must also make reliable electrical contact during antenna operation. In addition, the contacts must be compliant enough to survive deflection of the port during seismic and disruption events without transmitting large forces to the vacuum vessel. The distance to be spanned is subject to significant uncertainty, due to the large manufacturing tolerances of the surrounding components, and this also must be considered during the design process. This paper outlines progress made in the design of the grounding system, as well as detailing a number of concepts which have been investi...

  14. Analog and digital communication systems

    CERN Document Server

    Roden, Martin S

    1996-01-01

    New edition of an introductory text that balances theoretical foundations with practical design. Reorganization and updates in this edition include the section on digital communications as well as design applications and computer exercises: many graphs are prepared and formulas solved using MATLAB...

  15. Communication architectures for systems-on-chip

    CERN Document Server

    Ayala, Jose L

    2011-01-01

    A presentation of state-of-the-art approaches from an industrial applications perspective, Communication Architectures for Systems-on-Chip shows professionals, researchers, and students how to attack the problem of data communication in the manufacture of SoC architectures. With its lucid illustration of current trends and research improving the performance, quality, and reliability of transactions, this is an essential reference for anyone dealing with communication mechanisms for embedded systems, systems-on-chip, and multiprocessor architectures--or trying to overcome existing limitations.

  16. Design of a mechanically actuated RF grounding system for the ITER ICRH antenna

    Energy Technology Data Exchange (ETDEWEB)

    Hancock, David, E-mail: david.hancock@ccfe.ac.uk [EURATOM/CCFE Fusion Association, Culham Science Centre, Abingdon, OX14 5ER (United Kingdom); Shannon, Mark [EURATOM/CCFE Fusion Association, Culham Science Centre, Abingdon, OX14 5ER (United Kingdom); Beaumont, Bertrand [ITER Organisation, Route de Vinon sur Verdon, 13115 Saint Paul Lez Durance (France); Dumortier, Pierre; Durodie, Frederic; Kyrytsya, Volodymyr; Louche, Fabrice [LPP/ERM-KMS, Association EURATOM-Belgian State, Brussels (Belgium); McKinley, Robert; Nicholls, Keith [EURATOM/CCFE Fusion Association, Culham Science Centre, Abingdon, OX14 5ER (United Kingdom)

    2013-10-15

    Highlights: ► The requirements for RF grounding of the ITER ICRH antenna are outlined. ► A number of early concepts are presented and reasons given for their rejection. ► The current grounding contact design is presented and its operation explained. ► Analysis and testing have been undertaken and these results are outlined. -- Abstract: In the ITER equatorial ports containing ICRH antennas, parasitic electrical resonances can be excited in the nominal 20 mm clearance gap between the port walls and the plug contained within it. RF calculations have established that these resonances can be effectively mitigated by a series of suitably located electrically conducting contacts between the port and plug. These contacts must allow installation and removal of the antenna but must also make reliable electrical contact during antenna operation. In addition, the contacts must be compliant enough to survive deflection of the port during seismic and disruption events without transmitting large forces to the vacuum vessel. The distance to be spanned is subject to significant uncertainty, due to the large manufacturing tolerances of the surrounding components, and this also must be considered during the design process. This paper outlines progress made in the design of the grounding system, as well as detailing a number of concepts which have been investigated and abandoned, leading up to the current reference design. The current reference design is a simple and robust mechanical solution consisting of sprung Copper-plated Inconel flaps which use part of the range of the shimming system included in the antenna design as the actuation mechanism. This paper also details practical testing of a number of aspects of the design, including building and testing a prototype to validate mechanical and thermal analyses.

  17. Impedance matching network systems using stub-lines of 20 kW CW RF amplifier for SKKUCY-9 compact cyclotron

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Seung Hyun; Song, Ho Seung; Kim, Jeong Hwan; Cong, Truong Van; Kim, Hui Su; Yeon, Yeong Heum; Lee, Yong seok; Chai, Jong Seo, E-mail: jschai@skku.edu

    2015-01-21

    The SKKUCY-9 is a compact cyclotron for radioactive isotopes (RI) production of positron emission tomography (PET). Charged particles such as H-ions are accelerated azimuthally within a high intensity electric field (E-field) generated from a radio frequency (RF) system in cyclotron. A high power RF signal is transmitted from an RF amplifier to an RF resonating cavity. The RF system of the SKKUCY-9 operates in continuous wave (CW) mode. If an ion beam were accelerated in the cyclotron, the vacuum level and permittivity would be changed because of beam loading. It causes an impedance shift of the RF resonating cavity. This impedance mismatch generates reflected power that decreases the RF transmitting power. To prevent this situation, an impedance matching system is necessary. This paper describes the impedance matching system of a 20 kW RF amplifier in an SKKUCY-9 compact cyclotron. The impedance matching circuit was designed using both an input stage and output stage, which are divided between the cathode and anode in a vacuum tube that is used as an amplifying device. The equivalent circuit of the matching system is made of passive elements. The characteristic results of designed circuit were calculated using a Smith chart. In assembling, the inductors were replaced by movable stub-line structures. The dimensions of the stub-line structures were optimized with equations and the measurement results. The experiment was performed to find the result values of matching circuit impedance and RF power amplitude.

  18. WiMAX Based 60 GHz Millimeter-Wave Communication for Intelligent Transport System Applications

    CERN Document Server

    Bera, Rabindranath; Sharma, Bikash; Sur, Samarendra Nath; Bhaskar, Debasish; Bera, Soumyasree

    2011-01-01

    With the successful worldwide deployment of 3rd generation mobile communication, security aspects are ensured partly. Researchers are now looking for 4G mobile for its deployment with high data rate, enhanced security and reliability so that world should look for CALM, Continuous Air interface for Long and Medium range communication. This CALM will be a reliable high data rate secured mobile communication to be deployed for car to car communication (C2C) for safety application. This paper reviewed the WiMAX ,& 60 GHz RF carrier for C2C. The system is tested at SMIT laboratory with multimedia transmission and reception. With proper deployment of this 60 GHz system on vehicles, the existing commercial products for 802.11P will be required to be replaced or updated soon .

  19. 无人机机载通信设备间的射频电磁兼容预测分析%Analysis of RF Electromagnetic Compatibility Prediction Among UAV Airborne Communication Equipments

    Institute of Scientific and Technical Information of China (English)

    赵翌池; 宋祖勋; 李恒博

    2012-01-01

    由于无人机的内部空间狭小,设备安装拥挤,使得无人机系统内电磁环境相当复杂,恶劣的电磁环境导致设备间产生严重的干扰问题.因此,要保证无人机机载通信设备间的电磁兼容性,电磁兼容预测是一种非常有效的手段.本文根据无人机的特点,提出一种适用于无人机机载通信设备间射频电磁兼容性预测的干扰余量分析法.通过对设备进行频率预测和幅度预测,验证这种方法的有效性,从而为分析机载通信设备间的射频电磁兼容性提供一套有效方案.%As the internal space of UAV is limited and the equipments are closely installed, the electromagnetic environment of UAV system is fairly complex and the deteriorative electromagnetic environment causes serious interferences among different e-quipments. Therefore, electromagnetic compatibility prediction is a very effective means to ensure the electromagnetic compatibility among the UAV airborne communication equipments. According to the characteristics of UAV, an interference margin analysis method is proposed, which is fit for the RF electromagnetic compatibility prediction among the UAV airborne communication e-quipments. The effectiveness of this method is verified by the mathematical model of the airborne equipments about frequency and amplitude forecasting, which provides an effective solution for analyzing the RF electromagnetic compatibility among airborne communication equipments.

  20. Broadcast Communication by System Frequency Modulation

    DEFF Research Database (Denmark)

    Douglass, Philip James; You, Shi; Heussen, Kai

    2012-01-01

    off-nominal system frequency values is a novel narrowband broadcast communications channel between system operators and frequency sensitive distributed energy resources (FS-DER). The feasibility of the proposed system is evaluated on an existing island power system in Denmark. This study shows...

  1. Communication system at Dakshin Gangotri, Antarctica

    Digital Repository Service at National Institute of Oceanography (India)

    Sudhakar, T.

    A reliable communication system is a major requirement for a remote station like 'Dakshin Gangotri' where traditional equipments cannot function effectively due to long distances and peculiar weather and ionospheric conditions. The satellite...

  2. Extreme Environment High Temperature Communication Systems Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The purpose of this project is to develop and demonstrate a communications system capable of operation at extreme temperatures and pressures in hostile and corrosive...

  3. Cost-effective hybrid RF/FSO backhaul solution for next generation wireless systems

    KAUST Repository

    Dahrouj, Hayssam

    2015-10-28

    The rapid pace of demand for mobile data services and the limited supply of capacity in the current wireless access networks infrastructure are leading network operators to increase the density of base station deployments to improve network performance. This densification, made possible by small-cell deployment, also brings a novel set of challenges, specifically related to the cost of ownership, in which backhaul is of primary concern. This article proposes a cost-effective hybrid RF/free-space optical (FSO) solution to combine the advantages of RF backhauls (low cost, NLOS applications) and FSO backhauls (high-rate, low latency). To first illustrate the cost advantages of the RF backhaul solution, the first part of this article presents a business case of NLOS wireless RF backhaul, which has a low cost of ownership as compared to other backhaul candidates. RF backhaul, however, is limited by latency problems. On the other side, an FSO solution, which offers better latency and higher data rate than RF backhauls, remains sensitive to weather and nature conditions (e.g., rain, fog). To combine RF and FSO advantages, the second part of this article proposes a lowcost hybrid RF/FSO solution, wherein base stations are connected to each other using either optical fiber or hybrid RF/FSO links. This part addresses the problem of minimizing the cost of backhaul planning under reliability, connectivity, and data rate constraints, and proposes choosing the appropriate cost-effective backhaul connection between BSs (i.e., either OF or hybrid RF/FSO) using graph theory techniques.

  4. An RF-based wearable sensor system for indoor tracking to facilitate efficient healthcare management.

    Science.gov (United States)

    Yuzhe Ouyang; Shan, Kai; Bui, Francis Minhthang

    2016-08-01

    To understand the utilization of clinical resources and improve the efficiency of healthcare, it is often necessary to accurately locate patients and doctors in a healthcare facility. However, existing tracking methods, such as GPS, Wi-Fi and RFID, have technological drawbacks or impose significant costs, thus limiting their applications in many clinical environments, especially those with indoor enclosures. This paper proposes a low-cost and flexible tracking system that is well suited for operating in an indoor environment. Based on readily available RF transceivers and microcontrollers, our wearable sensor system can facilitate locating users (e.g., patients or doctors) or objects (e.g., medical devices) in a building. The strategic construction of the sensor system, along with a suitably designed tracking algorithm, together provide for reliability and dispatch in localization performance. For demonstration purposes, several simplified experiments, with different configurations of the system, are implemented in two testing rooms to assess the baseline performance. From the obtained results, our system exhibits immense promise in acquiring a user location and corresponding time-stamp, with high accuracy and rapid response. This capability is conducive to both short- and long-term data analytics, which are crucial for improving healthcare management.

  5. Directions for rf-controlled intelligent microvalve

    Science.gov (United States)

    Enderling, Stefan; Varadan, Vijay K.; Abbott, Derek

    2001-03-01

    In this paper, we consider the novel concept of a Radio Frequency (RF) controllable microvalve for different medical applications. Wireless communication via a Surface Acoustic Wave Identification-mark (SAW ID-tag) is used to control, drive and locate the microvalve inside the human body. The energy required for these functions is provided by RF pulses, which are transmitted to the valve and back by a reader/transmitter system outside of the body. These RF bursts are converted into Surface Acoustic Waves (SAWs), which propagate along the piezoelectric actuator material of the microvalve. These waves cause deflections, which are employed to open and close the microvalve. We identified five important areas of application of the microvalve in biomedicine: 1) fertility control; 2) artificial venous valves; 3) flow cytometry; 4) drug delivery and 5) DNA mapping.

  6. Bidirectional Radio-Over-Fiber System With Phase-Modulation Downlink and RF Oscillator-Free Uplink Using a Reflective SOA

    DEFF Research Database (Denmark)

    Yu, Xianbin; Gibbon, Timothy Braidwood; Tafur Monroy, Idelfonso

    2008-01-01

    We propose and demonstrate a bidirectional radio-over-fiber (RoF) system based on a reflective semiconductor optical amplifier (RSOA). In this system, phase-modulated 5.25-GHz radio frequency (RF) carrying 850 Mb/s is used for the downstream signal. Optical envelope detection of 10-GHz RF carryin...

  7. Protection of Communication System From Solar Flares

    OpenAIRE

    Karthik, K.(Department of Physics, New York University, New York, NY, United States of America); Shirvram, B.

    2008-01-01

    Solar flares are enormous explosions on the surface of the sun and they release energy of the order of billion megatons of TNThis energy is in the form of electromagnetic radiations such as alpha, gamma, and ultraviolet rays. When exposed to high doses of radiation like 2-15 kilorad (Si), silicon integrated circuits in satellite communication systems fail to operate properly, thus affecting the performance of communication systems. Therefore, the major issue that needs to be addressed is the ...

  8. A new slip stacking RF system for a twofold power upgrade of Fermilab's Accelerator Complex

    Energy Technology Data Exchange (ETDEWEB)

    Madrak, Robyn

    2014-09-11

    Fermilab@?s Accelerator Complex has been recently upgraded, in order to increase the 120GeV proton beam power on target from about 400kW to over 700kW for NO@nA and other future intensity frontier experiments. One of the key ingredients of the upgrade is the offloading of some Main Injector synchrotron operations - beam injection and RF manipulation called ''slip stacking'' - to the 8GeV Recycler Ring, which had until recently been used only for low-intensity antiproton storage and cooling. This required construction of two new 53MHz RF systems for the slip-stacking manipulations. The cavities operate simultaneously at V_p_e_a_k@?150kV, but at slightly different frequencies (@Df=1260Hz). Their installation was completed in September 2013. This paper describes the novel solutions used in the design of the new cavities, their tuning system, and the associated high power RF system. First results showing effective operation of the RF system, beam capture and successful slip-stacking in the Recycler Ring are presented.

  9. A new slip stacking RF system for a twofold power upgrade of Fermilab's Accelerator Complex

    Energy Technology Data Exchange (ETDEWEB)

    Madrak, Robyn [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States)

    2014-05-15

    Fermilab's Accelerator Complex has been recently upgraded, in order to increase the 120 GeV proton beam power on target from about 400 kW to over 700 kW for NOvA and other future intensity frontier experiments. One of the key ingredients of the upgrade is the offloading of some Main Injector synchrotron operations - beam injection and RF manipulation called ''slip stacking'' - to the 8GeV Recycler Ring, which had until recently been used only for low-intensity antiproton storage and cooling. This required construction of two new 53 MHz RF systems for the slip-stacking manipulations. The cavities operate simultaneously at Vpeak ≲150 kV, but at slightly different frequencies (Δf=1260 Hz). Their installation was completed in September 2013. This article describes the novel solutions used in the design of the new cavities, their tuning system, and the associated high power RF system. First results showing effective operation of the RF system, beam capture and successful slip-stacking in the Recycler Ring are presented.

  10. Performance Analysis of RF-FSO Multi-Hop Networks

    KAUST Repository

    Makki, Behrooz

    2017-05-12

    We study the performance of multi-hop networks composed of millimeter wave (MMW)-based radio frequency (RF) and free-space optical (FSO) links. The results are obtained in the cases with and without hybrid automatic repeat request (HARQ). Taking the MMW characteristics of the RF links into account, we derive closed-form expressions for the network outage probability. We also evaluate the effect of various parameters such as power amplifiers efficiency, number of antennas as well as different coherence times of the RF and the FSO links on the system performance. Finally, we present mappings between the performance of RF- FSO multi-hop networks and the ones using only the RF- or the FSO-based communication, in the sense that with appropriate parameter settings the same outage probability is achieved in these setups. The results show the efficiency of the RF-FSO setups in different conditions. Moreover, the HARQ can effectively improve the outage probability/energy efficiency, and compensate the effect of hardware impairments in RF-FSO networks. For common parameter settings of the RF-FSO dual- hop networks, outage probability 10^{-4} and code rate 3 nats-per-channel-use, the implementation of HARQ with a maximum of 2 and 3 retransmissions reduces the required power, compared to the cases with no HARQ, by 13 and 17 dB, respectively.

  11. Conceptual design of data acquisition and control system for two Rf driver based negative ion source for fusion R&D

    Science.gov (United States)

    Soni, Jigensh; Yadav, R. K.; Patel, A.; Gahlaut, A.; Mistry, H.; Parmar, K. G.; Mahesh, V.; Parmar, D.; Prajapati, B.; Singh, M. J.; Bandyopadhyay, M.; Bansal, G.; Pandya, K.; Chakraborty, A.

    2013-02-01

    Twin Source - An Inductively coupled two RF driver based 180 kW, 1 MHz negative ion source experimental setup is initiated at IPR, Gandhinagar, under Indian program, with the objective of understanding the physics and technology of multi-driver coupling. Twin Source [1] (TS) also provides an intermediate platform between operational ROBIN [2] [5] and eight RF drivers based Indian test facility -INTF [3]. A twin source experiment requires a central system to provide control, data acquisition and communication interface, referred as TS-CODAC, for which a software architecture similar to ITER CODAC core system has been decided for implementation. The Core System is a software suite for ITER plant system manufacturers to use as a template for the development of their interface with CODAC. The ITER approach, in terms of technology, has been adopted for the TS-CODAC so as to develop necessary expertise for developing and operating a control system based on the ITER guidelines as similar configuration needs to be implemented for the INTF. This cost effective approach will provide an opportunity to evaluate and learn ITER CODAC technology, documentation, information technology and control system processes, on an operational machine. Conceptual design of the TS-CODAC system has been completed. For complete control of the system, approximately 200 Nos. control signals and 152 acquisition signals are needed. In TS-CODAC, control loop time required is within the range of 5ms - 10 ms, therefore for the control system, PLC (Siemens S-7 400) has been chosen as suggested in the ITER slow controller catalog. For the data acquisition, the maximum sampling interval required is 100 micro second, and therefore National Instruments (NI) PXIe system and NI 6259 digitizer cards have been selected as suggested in the ITER fast controller catalog. This paper will present conceptual design of TS -CODAC system based on ITER CODAC Core software and applicable plant system integration processes.

  12. Spatial Modulation for MIMO Communication Systems

    Directory of Open Access Journals (Sweden)

    Reginaldo Nunes

    2012-11-01

    Full Text Available This work provides a review on the main spatial modulation (SM schemes, suitable to wireless communication systems. Performance, complexity and diversity gain of the three new spatial SM schemes suitable for multiple-input-multiple-output (MIMO communication systems are analyzed: a transmission scheme for spatial modulation (SM scheme; b space shift keying (SSK scheme; c generalized space shift keying (GSSK scheme. These three schemes offer low complexity, higher data rate when compared to single-input-single-output (SISO communication systems, as well as design flexibility, while exploits randomness characteristics of wireless communication channel for data transmission. The paper aims to explore the main features of those three SM schemes and to evaluate the inherent performance-complexity trade-off in order to determine which of those schemes results in a higher energy and spectral efficiencies.

  13. Converging Information and Communication Systems

    DEFF Research Database (Denmark)

    Øst, Alexander

    2003-01-01

    This Ph.D.-project investigates the process of convergence between television and computers. Identifying three “promises of convergence”: interoperability, quality and interactivity, the project examines the key properties of the computer and television sectors, which have had - or are expected...... in the future to have - significant importance to the process and consequences of the convergence. The project focuses on the appliances, i.e. the TV sets, the computers and their peripheral equipment. It also takes into account the infrastructure and signals, which contain and deliver the information...... and communication, as well as the nature of the content and the usage scenarios of consumers....

  14. Development of an automatic frequency control system for an X-band (=9300 MHz) RF electron linear accelerator

    Science.gov (United States)

    Cha, Sungsu; Kim, Yujong; Lee, Byung Cheol; Park, Hyung Dal; Lee, Seung Hyun; Buaphad, Pikad

    2017-05-01

    KAERI is developing a 6 MeV X-band radio frequency (RF) electron linear accelerator for medical purposes. The proposed X-band accelerator consists of an e-gun, an accelerating structure, two solenoid magnets, two steering magnets, a magnetron, a modulator, and an automatic frequency control (AFC) system. The accelerating structure of the component consists of oxygen-free high-conductivity copper (OFHC). Therefore, the ambient temperature changes the volume, and the resonance frequency of the accelerating structure also changes. If the RF frequency of a 9300 MHz magnetron and the resonance frequency of the accelerating structure do not match, it can degrade the performance. That is, it will decrease the output power, lower the beam current, decrease the X-ray dose rate, increase the reflection power, and result in unstable operation of the accelerator. Accelerator operation should be possible at any time during all four seasons. To prevent humans from being exposed to radiation when it is operated, the accelerator should also be operable through remote monitoring and remote control. Therefore, the AFC system is designed to meet these requirements; it is configured based on the concept of a phase-locked loop (PLL) model, which includes an RF section, an intermediate frequency (IF) [1-3] section, and a local oscillator (LO) section. Some resonance frequency controllers use a DC motor, chain, and potentiometer to store the position and tune the frequency [4,5]. Our AFC system uses a step motor to tune the RF frequency of the magnetron. The maximum tuning turn number of our magnetron frequency tuning shaft is ten. Since the RF frequency of our magnetron is 9300±25 MHz, it gives 5 MHz (∵±25 MHz/10 turns → 50 MHz/10 turns =5 MHz/turn) frequency tuning per turn. The rotation angle of our step motor is 0.72° per step and the total step number per one rotation is 360°/0.72°=500 steps. Therefore, the tuning range per step is 10 kHz/step (=5 MHz per turn/500 steps per

  15. Implementation Of Water Level Conditioning System Using Wireless Multi-Point Communication

    Directory of Open Access Journals (Sweden)

    Ohnmar Htwe

    2015-08-01

    Full Text Available Wireless communication is the most popular in these days. Recently people are trying to use the wireless communication systems in home appliances. In this system that is designed and development of a water level conditioning system using wireless which is being used to control the water distribution system. The development system based on the wireless RF Radio Frequency technology which can be installed in industries departments domestics and so on. The level controller is used with ultrasonic sensors to sense the level of water in the tanks and a reservoir. The system used microcontrollersthesecontrollers have the ability to detect the level of water in a Tank1 Tank2 and a Reservoir and then display the status of water on LCD screen and moreover the buzzer will be work depending on the condition of water level in a reservoir. The main objectives of this paper are to design and develop a wireless water level conditioning system using point-to-multi-point RF communication technology. It is reliable because it has no problems arising after installation such as a breakage of wire.

  16. Simulation of Wireless Digital Communication Systems

    Directory of Open Access Journals (Sweden)

    A. Mohammed

    2004-12-01

    Full Text Available Due to the explosive demands for high speed wireless services, suchas wireless Internet, email and cellular video conferencing, digitalwireless communications has become one of the most exciting researchtopics in electrical and electronic engineering field. The never-endingdemand for such personal and multimedia services, however, demandstechnologies operating at higher data rates and broader bandwidths. Inaddition, the complexity of wireless communication and signalprocessing systems has grown considerably during the past decade.Therefore, powerful computer­aided techniques are required for theprocess of modeling, designing, analyzing and evaluating theperformance of digital wireless communication systems. In this paper wediscuss the basic propagation mechanisms affecting the performance ofwireless communication systems, and present a simple, powerful andefficient way to simulate digital wireless communication systems usingMatlab. The simulated results are compared with the theoreticalanalysis to validate the simulator. The simulator is useful inevaluating the performance of wireless multimedia services and theassociated signal processing structures and algorithms for current andnext generation wireless mobile communication systems.

  17. 基于ARM11的嵌入式Linux中nRF24L01驱动的实现%Design of nRF24L01 Driver Based on Embedded Linux System Under ARM11

    Institute of Scientific and Technical Information of China (English)

    张頔; 宋欣; 王宇航; 宋占伟

    2015-01-01

    In order to meet the demands of wireless data transmission, as well as to resolve the lack of nRF24L01 driver based on Linux, the driver of nRF24L01 is designed based on Linux.nRF24L01 exchanges data with external controller through SPI interface. Firstly,we drive nRF24L01 by using GPIO to simulate the SPI timing to achieve the SPI read and write operation. Secondly, the design of the system is provided, and the hardware interface and software process is disserted and carry on the detailed elaboration to the key functions. Lastly it achieves nRF24L01's wireless transmisson and test to verify the correctness of the driver based on the embedded microprocessor S3C6410.%针对无线音频数据传输的需要,以及基于ARM11处理器的nRF24L01驱动程序的缺乏,设计了在Linux系统下基于ARM11处理器的nRF24L01模块驱动程序。nRF24L01模块通过SPI接口和外部控制器进行数据交换。首先,结合nRF24L01模块的性能特点和Linux系统下字符设备驱动开发的流程,通过GPIO接口软件模拟SPI时序实现SPI读写操作,从而驱动nRF24L01模块。其次,给出了系统的整体方案,论述了系统硬件接口和软件流程,并对部分关键函数进行详细阐述。最后,在嵌入式处理器S3C6410平台上实现nRF24L01的无线收发,通过测试以验证驱动程序的正确性。

  18. Matching Parasitic Antenna for Single RF MIMO

    DEFF Research Database (Denmark)

    Han, Bo; Kalis, A; Nielsen, Rasmus Hjorth

    2012-01-01

    Single RF MIMO communication emerges a novel low cost communication method which does not consume as much power as the conventional MIMO. The implementation of such single RF MIMO system is done by mapping the weighting factors to the polarizations or the radiation patterns of the antennas....... In order to have such performance, an antenna with rich pattern modes is required by the system, thus the ESPAR antenna is investigated. The critical part on such antenna is parasitic element impedance matching. Unlike the conventional smith-chart matching method which assumes the minimal resistance...... is zero and with goal of 50 ohm or 75 ohm matching, matching on such parasitic antenna will adopt negative value as well. This paper presents a matching network with controllable impedance even to the range of negative values....

  19. Microfluidic stretchable RF electronics.

    Science.gov (United States)

    Cheng, Shi; Wu, Zhigang

    2010-12-07

    Stretchable electronics is a revolutionary technology that will potentially create a world of radically different electronic devices and systems that open up an entirely new spectrum of possibilities. This article proposes a microfluidic based solution for stretchable radio frequency (RF) electronics, using hybrid integration of active circuits assembled on flex foils and liquid alloy passive structures embedded in elastic substrates, e.g. polydimethylsiloxane (PDMS). This concept was employed to implement a 900 MHz stretchable RF radiation sensor, consisting of a large area elastic antenna and a cluster of conventional rigid components for RF power detection. The integrated radiation sensor except the power supply was fully embedded in a thin elastomeric substrate. Good electrical performance of the standalone stretchable antenna as well as the RF power detection sub-module was verified by experiments. The sensor successfully detected the RF radiation over 5 m distance in the system demonstration. Experiments on two-dimensional (2D) stretching up to 15%, folding and twisting of the demonstrated sensor were also carried out. Despite the integrated device was severely deformed, no failure in RF radiation sensing was observed in the tests. This technique illuminates a promising route of realizing stretchable and foldable large area integrated RF electronics that are of great interest to a variety of applications like wearable computing, health monitoring, medical diagnostics, and curvilinear electronics.

  20. Communication and control for networked complex systems

    CERN Document Server

    Peng, Chen; Han, Qing-Long

    2015-01-01

    This book reports on the latest advances in the study of Networked Control Systems (NCSs). It highlights novel research concepts on NCSs; the analysis and synthesis of NCSs with special attention to their networked character; self- and event-triggered communication schemes for conserving limited network resources; and communication and control co-design for improving the efficiency of NCSs. The book will be of interest to university researchers, control and network engineers, and graduate students in the control engineering, communication and network sciences interested in learning the core principles, methods, algorithms and applications of NCSs.

  1. 基于nRF24L01的无线心音遥测系统研究与实现%Design of Wireless PCG Monitor System Based on nRF24L01

    Institute of Scientific and Technical Information of China (English)

    李才光; 裴正宪; 蒋洪波

    2013-01-01

    介绍了一种以射频芯片nRF24L01为无线通信核心的无线心音遥测系统的实现方案.整个系统通过8位单片机STC12C5A60S2来控制.STC12C5A60S2内部的10位ADC可以对放大滤波后的心音信号进行采集,再写入nRF24L01进行无线传输,接收端由单片机通过nRF24L01接收数据,再由UART通过串口将其传输到PC机进行显示与分析.经测试,该系统在室内通信良好,所显示的心音波形满足要求.此外就各模块的通信协议以及对应的程序也进行了具体分析.%This paper introduced the design of a wireless PCG monitor based on nRF24L01.The controller is STC12C5A60S2 with a 8 bit MCU.10 bit ADC in STC12C5A60S2 is used to convert the PCG signal which has been out of the amplifier and filter.The data will be writen in the memory of nRF24L01 and be transmitted.The receiver takes the data and sends them to computer for display and analysis.The result of testing shows that the indoor communication is well and waveform of PCG meets the requirements.In addition,the communication protocol and the program were also analyzed.

  2. RF gymnastics in synchrotrons

    CERN Document Server

    Garoby, R

    2011-01-01

    The RF systems installed in synchrotrons can be used to change the longitudinal beam characteristics. 'RF gymnastics' designates manipulations of the RF parameters aimed at providing such non-trivial changes. Some keep the number of bunches constant while changing bunch length, energy spread, emittance, or distance between bunches. Others are used to change the number of bunches. After recalling the basics of longitudinal beam dynamics in a hadron synchrotron, this paper deals with the most commonly used gymnastics. Their principle is described as well as their performance and limitations.

  3. RF Gymnastics in Synchrotrons

    CERN Document Server

    Garoby, R

    2005-01-01

    The RF systems installed in synchrotrons can be used to change the longitudinal beam characteristics. "RF gymnastics" designates manipulations of the RF parameters aimed at providing such non-trivial changes. Some keep the number of bunches constant while changing bunch length, energy spread, emittance or distance between bunches. Others are used to change the number of bunches. After recalling the basics of longitudinal beam dynamics in a hadron synchrotron, this paper deals with the most commonly used gymnastics. Their principle is described as well as their performance and limitations.

  4. A native IP satellite communications system

    Science.gov (United States)

    Koudelka, O.; Schmidt, M.; Ebert, J.; Schlemmer, H.; Kastner-Puschl, S.; Riedler, W.

    2004-08-01

    ≪ In the framework of ESA's ARTES-5 program the Institute of Applied Systems Technology (Joanneum Research) in cooperation with the Department of Communications and Wave Propagation has developed a novel meshed satellite communications system which is optimised for Internet traffic and applications (L*IP—Local Network Interconnection via Satellite Systems Using the IP Protocol Suite). Both symmetrical and asymmetrical connections are supported. Bandwidth on demand and guaranteed quality of service are key features of the system. A novel multi-frequency TDMA access scheme utilises efficient methods of IP encapsulation. In contrast to other solutions it avoids legacy transport network techniques. While the DVB-RCS standard is based on ATM or MPEG transport cells, the solution of the L*IP system uses variable-length cells which reduces the overhead significantly. A flexible and programmable platform based on Linux machines was chosen to allow the easy implementation and adaptation to different standards. This offers the possibility to apply the system not only to satellite communications, but provides seamless integration with terrestrial fixed broadcast wireless access systems. The platform is also an ideal test-bed for a variety of interactive broadband communications systems. The paper describes the system architecture and the key features of the system.

  5. RF Power Detector/Monitor Upgrade for the 500MHz Systems at the ALS

    Energy Technology Data Exchange (ETDEWEB)

    Baptiste, K.

    2003-05-08

    Several systems rely on the accurate and linear detection of 500 MHz signals, (the fundamental frequency of both the Booster Ring and Storage Ring) over a dynamic range in excess of 25dB. Prior to this upgrade, the detector/monitor was diode based and though this type of detector could handle the dynamic range requirement it could not do so in an accurate and linear manner. In order to meet the requirements (dynamic range greater than or equal to 25dB, accurate and linear to +-0.25dB over the range, and additional circuitry to interface to the legacy control system and interlocks), a new RF Power Detector/Monitor has been developed using two AD8361, Analog Devices Tru RMS Detectors and a fuzzy comparator, which extends the overall detector's range to twice that of the AD8361. Further information is available [www.analogedevices.com/]. Details of the design requirements and the detector/monitor's circuit as well as the performance of the detector will be presented.

  6. A systems approach to animal communication.

    Science.gov (United States)

    Hebets, Eileen A; Barron, Andrew B; Balakrishnan, Christopher N; Hauber, Mark E; Mason, Paul H; Hoke, Kim L

    2016-03-16

    Why animal communication displays are so complex and how they have evolved are active foci of research with a long and rich history. Progress towards an evolutionary analysis of signal complexity, however, has been constrained by a lack of hypotheses to explain similarities and/or differences in signalling systems across taxa. To address this, we advocate incorporating a systems approach into studies of animal communication--an approach that includes comprehensive experimental designs and data collection in combination with the implementation of systems concepts and tools. A systems approach evaluates overall display architecture, including how components interact to alter function, and how function varies in different states of the system. We provide a brief overview of the current state of the field, including a focus on select studies that highlight the dynamic nature of animal signalling. We then introduce core concepts from systems biology (redundancy, degeneracy, pluripotentiality, and modularity) and discuss their relationships with system properties (e.g. robustness, flexibility, evolvability). We translate systems concepts into an animal communication framework and accentuate their utility through a case study. Finally, we demonstrate how consideration of the system-level organization of animal communication poses new practical research questions that will aid our understanding of how and why animal displays are so complex. © 2016 The Author(s).

  7. Design and evaluation of a low-level RF control system analog/digital receiver for the ILC main Linacs

    Energy Technology Data Exchange (ETDEWEB)

    Mavric, Uros; Vidmar, Matjaz; Chase, Brian; /Fermilab

    2008-06-01

    The proposed RF distribution scheme for the two 15 km long ILC LINACs, uses one klystron to feed 26 superconducting RF cavities operating at 1.3 GHz. For a precise control of the vector sum of the signals coming from the SC cavities, the control system needs a high performance, low cost, reliable and modular multichannel receiver. At Fermilab we developed a 96 channel, 1.3 GHz analog/digital receiver for the ILC LINAC LLRF control system. In the paper we present a balanced design approach to the specifications of each receiver section, the design choices made to fulfill the goals and a description of the prototyped system. The design is tested by measuring standard performance parameters, such as noise figure, linearity and temperature sensitivity. Measurements show that the design meets the specifications and it is comparable to other similar systems developed at other laboratories, in terms of performance.

  8. Design and evaluation of a low-level RF control system analog/digital receiver for the ILC main LINACs

    Energy Technology Data Exchange (ETDEWEB)

    Mavric, Uros [Fermilab, P.O. Box 500, 60510 Batavia, IL (United States)], E-mail: mavric@fnal.gov; Chase, Brian [Fermilab, P.O. Box 500, 60510 Batavia, IL (United States); Vidmar, Matjaz [Faculty of Electrical Engineering in Ljubljana, Trzaska 25, 1000 Ljubljana (Slovenia)

    2008-08-21

    The proposed RF distribution scheme for the two 15 km long ILC LINACs uses one klystron to feed 26 superconducting RF cavities operating at 1.3 GHz. For a precise control of the vector sum of the signals coming from the SC cavities, the control system needs a high-performance, low-cost, reliable and modular multichannel receiver. At Fermilab we developed a 96-channel, 1.3 GHz analog/digital receiver for the ILC LINAC LLRF control system. In this paper we present a balanced design approach to the specifications of each receiver section, the design choices made to fulfill the goals and a description of the prototyped system. The design is tested by measuring standard performance parameters, such as noise figure, linearity and temperature sensitivity. Measurements show that the design meets the specifications and it is comparable to other similar systems developed at other laboratories, in terms of performance.

  9. Concepts for a short wavelength rf gun

    Science.gov (United States)

    Kuzikov, S. V.; Shchelkunov, S.; Vikharev, A. A.

    2017-03-01

    Three concepts of an rf gun to be operated at 0.1-10 mm wavelengths are considered. In all the concepts, the rf system exploits an accelerating traveling wave. In comparison with a classical decimeter standing-wave rf gun, we analyze the advantages of new concepts, available rf sources, and achievable beam parameters.

  10. 5G Wireless Communication Systems

    Directory of Open Access Journals (Sweden)

    Saddam Hossain

    2013-10-01

    Full Text Available As a subscriber becomes more aware of the mobile phone technology, he/she will seek for anappropriate package all together, including all the advanced features of a cellular phone can have. Hence, the search for new technology is always the main intention of the prime cell phone giants to out innovate their competitors. In addition, the main purpose of the fifth generation wireless networks (5G Wireless networks is planned to design the best wireless world that is free from limitations and hindrance of the previous generations.5G technologies will change the way most high bandwidth users access their Mobile Radio Communication (MRC. So, this paper represents, great evolution of 1G (First Generation to 4G yield 5G, introduction to 5G technologies, why there is a need for 5G, advantages of 5G networks technology, exceptional applications, Quality of Service (QoS, 5G network architecture-The MasterCore as well as hardware and software for the 5GMasterCore technology

  11. The communication of meaning in social systems

    NARCIS (Netherlands)

    Leydesdorff, L.; Franse, S.

    2009-01-01

    The sociological domain is different from the psychological one insofar as meaning can be communicated at the supra-individual level. The computation of anticipatory systems enables us to distinguish between these domains in terms of weakly and strongly anticipatory systems with a structural

  12. An RF-input outphasing power amplifier with RF signal decomposition network

    OpenAIRE

    Barton, Taylor W.; Perreault, David J.

    2015-01-01

    This work presents an outphasing power amplifier that directly amplifies a modulated RF input. The approach eliminates the need for multiple costly IQ modulators and baseband signal component separation found in conventional outphasing power amplifier systems, which have previously required both an RF carrier input and a separate baseband input to synthesize a modulated RF output. A novel RF signal decomposition network enables direct RF-input / RF-output outphasing by directly synthesizing t...

  13. Communication Scheme via Cascade Chaotic Systems

    Institute of Scientific and Technical Information of China (English)

    HUA Chang-Chun; GUAN Xin-Ping

    2004-01-01

    @@ A new chaotic communication scheme is constructed. Different from the existing literature, cascade chaotic systems are employed. Two cascade modes are considered. First, we investigate the input to state cascade mode;cascade systems between different kinds of chaotic systems are considered. Then the parameter cascade case of chaotic system is studied. Under the different cases, the corresponding receivers are designed, which can succeed in recovering the former emitted signal. Simulations are performed to verify the validity of the proposed main results.

  14. Power Adaptation Based on Truncated Channel Inversion for Hybrid FSO/RF Transmission With Adaptive Combining

    KAUST Repository

    Rakia, Tamer

    2015-07-23

    Hybrid free-space optical (FSO)/radio-frequency (RF) systems have emerged as a promising solution for high-data-rate wireless communications. In this paper, we consider power adaptation strategies based on truncated channel inversion for the hybrid FSO/RF system employing adaptive combining. Specifically, we adaptively set the RF link transmission power when FSO link quality is unacceptable to ensure constant combined signal-to-noise ratio (SNR) at the receiver. Two adaptation strategies are proposed. One strategy depends on the received RF SNR, whereas the other one depends on the combined SNR of both links. Analytical expressions for the outage probability of the hybrid system with and without power adaptation are obtained. Numerical examples show that the hybrid FSO/RF system with power adaptation achieves a considerable outage performance improvement over the conventional system.

  15. Intelligent Wireless Communication System Using Cognitive Radio

    Directory of Open Access Journals (Sweden)

    Asma Amraoui

    2012-04-01

    Full Text Available The increasing demand for wireless communication introduces efficient spectrum utilization challenge. To address this challenge, cognitive radio (CR is emerged as the key technology; which enables opportunistic access to the spectrum. CR is a form of wireless communication in which a transceiver can intelligently detect which communication channels are in use and which are not, and instantly move into vacant channels while avoiding occupied ones. This optimizes the use of available radio-frequency (RFspectrum while minimizing interference to other users. In this paper, we present a state of the art onthe use of Multi Agent Systems (MAS for spectrum access using cooperation and competition to solve the problem of spectrum allocation and ensure better management. Then we propose a new approach which uses the CR for improving wireless communication for a single cognitive radio mobile terminal (CRMT.

  16. Abnormal glow discharge as a variable capacitor for tunable RF systems

    Science.gov (United States)

    Macheret, Sergey; Semnani, Abbas; Peroulis, Dimitrios

    2016-09-01

    For frequency-tunable resonators and filters in high-power applications, conventional semiconductor devices are easily damaged, while mechanically-tunable systems are bulky and slow. In this regard, weakly ionized plasmas can offer an attractive solution. In this work, an LC resonator circuit where a commercial gas discharge tube (GDT) serves as a variable capacitor was studied experimentally and theoretically. The experiments show continuous decrease of the resonant frequency by up to 50 percent with increase in the DC current through the GDT. Analysis of the current-voltage characteristic and the breakdown parameters, combined with lumped-parameter equivalent-circuit RF simulations, allowed us to determine the gas pressure, the electrode coating material and the secondary emission coefficient, and to achieve a very good agreement between the calculated and measured transmittance values. The analysis reveals that reduction in the cathode sheath thickness with increase in the DC current in the abnormal glow discharge regime is the key factor responsible for the experimentally observed tunability.

  17. Principles and Limitations of Ultra-Wideband FM Communications Systems

    Directory of Open Access Journals (Sweden)

    Kouwenhoven Michiel HL

    2005-01-01

    Full Text Available This paper presents a novel UWB communications system using double FM: a low-modulation index digital FSK followed by a high-modulation index analog FM to create a constant-envelope UWB signal. FDMA techniques at the subcarrier level are exploited to accommodate multiple users. The system is intended for low (1–10 kbps and medium (100–1000 kbps bit rate, and short-range WPAN systems. A wideband delay-line FM demodulator that is not preceded by any limiting amplifier constitutes the key component of the UWBFM receiver. This unusual approach permits multiple users to share the same RF bandwidth. Multipath, however, may limit the useful subcarrier bandwidth to one octave. This paper addresses the performance with AWGN and multipath, the resistance to narrowband interference, as well as the simultaneous detection of multiple FM signals at the same carrier frequency. SPICE and Matlab simulation results illustrate the principles and limitations of this new technology. A hardware demonstrator has been realized and has allowed the confirmation of theory with practical results.

  18. Security Problem of Communication in CORBA System

    Directory of Open Access Journals (Sweden)

    Jedrzej Byrski

    2002-01-01

    Full Text Available CORBA standard defines the mechanisms of shearing services. The key rule plays ORB (Object Request Broker which enables location of suitable server and transparent communication between client and server: This paper presents problems connected with security during communication between ORB systems. In the CORBA system the objects are identified by IOR (Interoperable Object Reference. For T CP/IP it contains IP server address, port and object key. Filtration may use such information as: type of communicate, IP address of client, object key to which client wants to access, type of operation, clients principal. In proposed implementation the firewall works as CORBA server and cooperates with half bridge. It is registered in ORB system and provides the controlling functions for entering packages by IDL interface. In the paper also the structure of filtering module is presented. Its main part is ACL (Access Control Lisa with rules of access. The performance evaluation results are also presented.

  19. Lymphangioma communicating with the excretory system.

    Science.gov (United States)

    Pancione, L; Giacomelli, G; Moroni, M; Taraglio, G; Mecozzi, B

    2008-03-01

    Lymphangioma is a rare benign tumor caused by failure in the development of the lymphatic communicating system. The corresponding nomenclature is confusing. In recent years ''renal lymphangiectasia'' is the preferred name. Although this disease may occur in any site of the body, the neck (75%) and axillary area (20%) are the most common sites, and the kidney is occasionally involved. We report a case of lymphangioma communicating with the urinary system in a 61-year-old man diagnosed by CT scan treated with nephrectomy and histological confirmation.

  20. Transceiver and system design for digital communications

    CERN Document Server

    Bullock, Scott

    2009-01-01

    Now in a 3rd edition, this successful book provides an intuitive approach to transceiver design, allowing a broad spectrum of readers to understand the topics clearly. It covers a wide range of data link communication design techniques, including link budgets, dynamic range and system analysis of receivers and transmitters used in data link communications, digital modulation and demodulation techniques of phase-shift keyed and frequency hopped spread spectrum systems using phase diagrams, multipath, gain control, an intuitive approach to probability, jamming reduction method using various adap

  1. MIMO Transmission with Residual Transmit-RF Impairments

    CERN Document Server

    Studer, Christoph; Burg, Andreas

    2010-01-01

    Physical transceiver implementations for multiple-input multiple-output (MIMO) wireless communication systems suffer from transmit-RF (Tx-RF) impairments. In this paper, we study the effect on channel capacity and error-rate performance of residual Tx-RF impairments that defy proper compensation. In particular, we demonstrate that such residual distortions severely degrade the performance of (near-)optimum MIMO detection algorithms. To mitigate this performance loss, we propose an efficient algorithm, which is based on an i.i.d. Gaussian model for the distortion caused by these impairments. In order to validate this model, we provide measurement results based on a 4-stream Tx-RF chain implementation for MIMO orthogonal frequency-division multiplexing (OFDM).

  2. Wireless communication system via nanoscale plasmonic antennas.

    Science.gov (United States)

    Merlo, Juan M; Nesbitt, Nathan T; Calm, Yitzi M; Rose, Aaron H; D'Imperio, Luke; Yang, Chaobin; Naughton, Jeffrey R; Burns, Michael J; Kempa, Krzysztof; Naughton, Michael J

    2016-08-24

    Present on-chip optical communication technology uses near-infrared light, but visible wavelengths would allow system miniaturization and higher energy confinement. Towards this end, we report a nanoscale wireless communication system that operates at visible wavelengths via in-plane information transmission. Here, plasmonic antenna radiation mediates a three-step conversion process (surface plasmon → photon → surface plasmon) with in-plane efficiency (plasmon → plasmon) of 38% for antenna separation 4λ0 (with λ0 the free-space excitation wavelength). Information transmission is demonstrated at bandwidths in the Hz and MHz ranges. This work opens the possibility of optical conveyance of information using plasmonic antennas for on-chip communication technology.

  3. Wireless communication system via nanoscale plasmonic antennas

    Science.gov (United States)

    Merlo, Juan M.; Nesbitt, Nathan T.; Calm, Yitzi M.; Rose, Aaron H.; D'Imperio, Luke; Yang, Chaobin; Naughton, Jeffrey R.; Burns, Michael J.; Kempa, Krzysztof; Naughton, Michael J.

    2016-08-01

    Present on-chip optical communication technology uses near-infrared light, but visible wavelengths would allow system miniaturization and higher energy confinement. Towards this end, we report a nanoscale wireless communication system that operates at visible wavelengths via in-plane information transmission. Here, plasmonic antenna radiation mediates a three-step conversion process (surface plasmon → photon → surface plasmon) with in-plane efficiency (plasmon → plasmon) of 38% for antenna separation 4λ0 (with λ0 the free-space excitation wavelength). Information transmission is demonstrated at bandwidths in the Hz and MHz ranges. This work opens the possibility of optical conveyance of information using plasmonic antennas for on-chip communication technology.

  4. Enhancing Secrecy With Multiantenna Transmission in Millimeter Wave Vehicular Communication Systems

    KAUST Repository

    Eltayeb, Mohammed E.

    2017-03-14

    Millimeter wave (mmWave) vehicular communication systems will provide an abundance of bandwidth for the exchange of raw sensor data and support driver-assisted and safety-related functionalities. Lack of secure communication links, however, may lead to abuses and attacks that jeopardize the efficiency of transportation systems and the physical safety of drivers. In this paper, we propose two physical layer (PHY) security techniques for vehicular mmWave communication systems. The first technique uses multiple antennas with a single radio-frequency (RF) chain to transmit information symbols to a target receiver and noise-like signals in nonreceiver directions. The second technique uses multiple antennas with a few RF chains to transmit information symbols to a target receiver and opportunistically inject artificial noise in controlled directions, thereby reducing interference in vehicular environments. Theoretical and numerical results show that the proposed techniques provide higher secrecy rate when compared to traditional PHY security techniques that require digital or more complex antenna architectures.

  5. Design Concepts for RF-DC Conversion in Particle Accelerator Systems

    CERN Document Server

    Caspers, F; Grudiev, A; Sapotta, H

    2010-01-01

    In many particle accelerators considerable amounts of RF power reaching the megawatt level are converted into heat in dummy loads. After an overview of RF power in the range 200 MHz to 1 GHz dissipated at CERN we discuss several developments that have come up in the past using vacuum tube technology for RF-DC conversion. Amongst those the developments of the cyclotron wave converter CWC appears most suitable. With the availability of powerful Schottky diodes the solid state converter aspect has to be addressed as well. One of the biggest problems of Schottky diode based structures is the junction capacity. GaAs and GaN Schottky diodes show a significant reduction of this junction capacity as compared to silicon. Small rectenna type converter units which have been already developed for microwave powered helicopters can be used in waveguides or with coaxial power dividers.

  6. Test and diagnosis of analogue, mixed-signal and RF integrated circuits the system on chip approach

    CERN Document Server

    Sun, Yichuang

    2008-01-01

    This book provides a comprehensive discussion of automatic testing, diagnosis and tuning of analogue, mixed-signal and RF integrated circuits, and systems in a single source. The book contains eleven chapters written by leading researchers worldwide. As well as fundamental concepts and techniques, the book reports systematically the state of the arts and future research directions of these areas. A complete range of circuit components are covered and test issues are also addressed from the SoC perspective.

  7. Robust Stackelberg game in communication systems

    CERN Document Server

    parsaeefard, saeedeh; Sharafat, Ahmad R

    2011-01-01

    This paper studies multi-user communication systems with two groups of users: leaders which possess system information, and followers which have no system information using the formulation of Stackelberg games. In such games, the leaders play and choose their actions based on their information about the system and the followers choose their actions myopically according to their observations of the aggregate impact of other users. However, obtaining the exact value of these parameters is not practical in communication systems. To study the effect of uncertainty and preserve the players' utilities in these conditions, we introduce a robust equilibrium for Stackelberg games. In this framework, the leaders' information and the followers' observations are uncertain parameters, and the leaders and the followers choose their actions by solving the worst-case robust optimizations. We show that the followers' uncertain parameters always increase the leaders' utilities and decrease the followers' utilities. Conversely,...

  8. A novel ECG telemetry and monitoring system based on Z-Wave communication.

    Science.gov (United States)

    Csernath, Geza; Szilagyi, Laszlo; Fordos, Gergely; Szilagyi, Sandor M

    2008-01-01

    This paper presents a novel ECG telemetry system based on Z-Wave communication protocol. The proposed system consists of small portable devices that acquire, compress and transmit the ECG to a RF-USB interface connected to a central monitoring computer. The received signals are filtered, QRS complexes and P and T waves are localized, and different waveforms are classified in order to be able to provide diagnosis tools like heart rate variability and turbulence analysis. Due to the limitation of communication bandwidth, the maximum number of measuring devices connected to a central monitor is four. The proposed system composed of inexpensive components can serve as flexible alternative to current ECG monitoring systems.

  9. 3rd International Conference on Communications, Signal Processing, and Systems

    CERN Document Server

    Liang, Qilian; Wang, Wei; Zhang, Baoju; Pi, Yiming

    2015-01-01

    The Proceedings of The Third International Conference on Communications, Signal Processing, and Systems provides the state-of-art developments of communications, signal processing, and systems. This book is a collection of contributions from the conference and covers such topics as wireless communications, networks, systems, and signal processing for communications. The conference was held July 2014 in Hohhot, Inner Mongolia, China.

  10. The quadrupole resonator Construction, RF System Field Calculations and First Applications

    CERN Document Server

    Chiaveri, Enrico; Mahner, E; Tessier, J M

    1998-01-01

    The quadrupole resonator allows measurement of the RF properties of superconducting (sc) films deposited on disk-shaped metallic substrates. We describe the construction of the apparatus, the brazing and electron-beam welding procedures, the arrangements for compensating mechanical tolerances of samples and for assuring reproducible sample illumination. We explain the special features of the RF sy stem and give the results of field calculations with a 3D cavity code. Finally we present first measurements of Nb on Cu film samples and compare them with calibrations done with a bulk Nb sample.

  11. Communications and Tracking Distributed Systems Evolution Study

    Science.gov (United States)

    Culpepper, William

    1990-01-01

    The Communications and Tracking (C & T) techniques and equipment to support evolutionary space station concepts are being analyzed. Evolutionary space station configurations and operational concepts are used to derive the results to date. A description of the C & T system based on future capability needs is presented. Included are the hooks and scars currently identified to support future growth.

  12. Manual communication systems: evolution and variation

    NARCIS (Netherlands)

    Pfau, R.; Pfau, R.; Steinbach, M.; Woll, B.

    2012-01-01

    This chapter addresses issues in the evolution and typology of manual communication systems. From a language evolution point of view, sign languages are interesting because it has been suggested that oral language may have evolved from gestural (proto)language. As far as typology is concerned, two i

  13. A system dynamics model for communications networks

    Science.gov (United States)

    Awcock, A. J.; King, T. E. G.

    1985-09-01

    An abstract model of a communications network in system dynamics terminology is developed as implementation of this model by a FORTRAN program package developed at RSRE is discussed. The result of this work is a high-level simulation package in which the performance of adaptive routing algorithms and other network controls may be assessed for a network of arbitrary topology.

  14. Transforming student learning with classroom communication systems

    CERN Document Server

    Beatty, I D

    2005-01-01

    Since 1993, the University of Massachusetts Physics Education Research Group (UMPERG) has developed curriculum and pedagogic techniques for use with classroom communication systems (CCSs) and has researched the effectiveness of CCS-based teaching. This bulletin describes how CCSs can influence "interactive pedagogy" and fundamentally transform the learning process. It includes advice drawn from lessons learned through a decade of experience.

  15. GaAs devices for new mobile communication systems application

    OpenAIRE

    Pettenpaul, E.; Schopf, K.J.

    1992-01-01

    A set of GaAs SMD devices has been developed for use in the new european mobile communication equipment, i.e. for DECT and PCN at 1900 and 1800 MHz, respectively. These devices cover the rf part of mobile communication terminals. The devices considered are a GaAs LNC chip for the receiver part, an upconversion mixer MMIC, a prescaler and GaAs power MESFETs as end-stages for the transmitter. The complete DECT, PCN block circuit including GaAs and Si devices will be described.

  16. RF Measurement Concepts

    CERN Document Server

    Caspers, F

    2014-01-01

    For the characterization of components, systems and signals in the radiofrequency (RF) and microwave ranges, several dedicated instruments are in use. In this article the fundamentals of the RF signal techniques are discussed. The key element in these front ends is the Schottky diode which can be used either as a RF mixer or as a single sampler. The spectrum analyser has become an absolutely indispensable tool for RF signal analysis. Here the front end is the RF mixer as the RF section of modern spectrum analyses has a ra ther complex architecture. The reasons for this complexity and certain working principles as well as limitations are discussed. In addition, an overview of the development of scalar and vector signal analysers is given. For the determination of the noise temperature of a one-port and the noise figure of a two-port, basic concepts and relations are shown as well as a brief discussion of commonly used noise-measurement techniques. In a further part of this article the operating principles of n...

  17. Second International Conference on Communications, Signal Processing, and Systems

    CERN Document Server

    Mu, Jiasong; Wang, Wei; Liang, Qilian; Pi, Yiming

    2014-01-01

    The Proceedings of The Second International Conference on Communications, Signal Processing, and Systems provides the state-of-art developments of Communications, Signal Processing, and Systems. The conference covered such topics as wireless communications, networks, systems, signal processing for communications. This book is a collection of contributions coming out of The Second International Conference on Communications, Signal Processing, and Systems (CSPS) held September 2013 in Tianjin, China.

  18. Wireless Energy and Information Transmission in FSO and RF-FSO Links

    KAUST Repository

    Makki, Behrooz

    2017-09-22

    We propose and analyze a wireless energy and information transmission scheme in free-space optical (FSO) links. The results are presented for both quasi-static and fast-fading conditions. We derive closed-form expressions for throughput, outage probability and optimal power allocation optimizing the system throughput/outage probability. Finally, we complement the FSO link with an additional radio frequency (RF) link to create a hybrid RF-FSO system and reduce the system outage probability. The results show that joint implementation of the RF and FSO links leads to considerable performance improvement, compared to the cases with only FSO-based communication.

  19. Ka-Band Link Study and Analysis for a Mars Hybrid RF/Optical Software Defined Radio

    Science.gov (United States)

    Zeleznikar, Daniel J.; Nappier, Jennifer M.; Downey, Joseph A.

    2014-01-01

    The integrated radio and optical communications (iROC) project at the NASA Glenn Research Center (GRC) is investigating the feasibility of a hybrid RF and optical communication subsystem for future deep space missions. The hybrid communications subsystem enables the advancement of optical communications while simultaneously mitigating the risk of infusion by combining an experimental optical transmitter and telescope with a reliable Ka-band RF transmitter and antenna. The iROC communications subsystem seeks to maximize the total data return over the course of a potential 2-year mission in Mars orbit beginning in 2021. Although optical communication by itself offers potential for greater data return over RF, the reliable Ka-band link is also being designed for high data return capability in this hybrid system. A daily analysis of the RF link budget over the 2-year span is performed to optimize and provide detailed estimates of the RF data return. In particular, the bandwidth dependence of these data return estimates is analyzed for candidate waveforms. In this effort, a data return modeling tool was created to analyze candidate RF modulation and coding schemes with respect to their spectral efficiency, amplifier output power back-off, required digital to analog conversion (DAC) sampling rates, and support by ground receivers. A set of RF waveforms is recommended for use on the iROC platform.

  20. An RF energy harvester system using UHF micropower CMOS rectifier based on a diode connected CMOS transistor.

    Science.gov (United States)

    Shokrani, Mohammad Reza; Khoddam, Mojtaba; Hamidon, Mohd Nizar B; Kamsani, Noor Ain; Rokhani, Fakhrul Zaman; Shafie, Suhaidi Bin

    2014-01-01

    This paper presents a new type diode connected MOS transistor to improve CMOS conventional rectifier's performance in RF energy harvester systems for wireless sensor networks in which the circuits are designed in 0.18  μm TSMC CMOS technology. The proposed diode connected MOS transistor uses a new bulk connection which leads to reduction in the threshold voltage and leakage current; therefore, it contributes to increment of the rectifier's output voltage, output current, and efficiency when it is well important in the conventional CMOS rectifiers. The design technique for the rectifiers is explained and a matching network has been proposed to increase the sensitivity of the proposed rectifier. Five-stage rectifier with a matching network is proposed based on the optimization. The simulation results shows 18.2% improvement in the efficiency of the rectifier circuit and increase in sensitivity of RF energy harvester circuit. All circuits are designed in 0.18 μm TSMC CMOS technology.

  1. An RF driven H{sup {minus}} source and a low energy beam injection system for RFQ operation

    Energy Technology Data Exchange (ETDEWEB)

    Leung, K.N.; Bachman, D.A.; Chan, C.F.; McDonald, D.S.

    1992-12-31

    An RF driven H{sup {minus}} source has been developed at LBL for use in the Superconducting Super Collider (SSC). To date, an H{sup {minus}} current of {approx}40 mA can be obtained from a 5.6-cm-diam aperture with the source operated at a pressure of about 12 m Torr and 50 kW of RF power. In order to match the accelerated H{sup {minus}} beam into the SSC RFQ, a low-energy H{sup {minus}} injection system has been designed. This injector produces an outgoing H{sup {minus}} beam free of electron contamination, with small radius, large convergent angle and small projectional emittance.

  2. Packet Reordering Procedure with Ubiquous Communication Systems

    Directory of Open Access Journals (Sweden)

    Giridhar Akula

    2012-11-01

    Full Text Available Satellite links are going to play a vital role in the deployment of ubiquous broad band systems. Non- Geostationary (NGEO satellite communication systems are more advantageous than terrestrial satellites. This paper presents an exchange of information on cooperation status among neiboring satellites. The new explicit load balancing scheme is used to avoid congestion and packet drops at the satellite. A TTL based algorithm is used for packet reordering.

  3. Emoticon recommendation system for effective communication

    OpenAIRE

    Urabe, Yuki; Rzepka, Rafal; Araki, Kenji

    2013-01-01

    The existence of social media has made computer- mediated communication more widespread among users around the world. This paper describes the development of an emoticon recommendation system that allows users to express their feelings with their input. In order to develop this system, an innovative emoticon database consisting of a table of emoticons with points expressed from each of 10 distinctive emotions was constructed. An evaluation experiment showed that 71.3% of user-selected emotico...

  4. Communication and tracking system evolution study

    Science.gov (United States)

    Culpepper, William

    1990-01-01

    The communications and tracking (C&T) techniques and equipment to support evolutionary space station concepts are being analyzed. Evolutionary space station configurations and operational concepts were used in the analysis to derive the results to date. A description of the C&T system based on future capability needs is presented. Included are the 'hooks and scars' currently identified to support the future growth. Technology transparency and impact of growth on other systems are also addressed.

  5. Analysis of Unmmanned Air Vehicles Communication Systems

    Directory of Open Access Journals (Sweden)

    Darius Rudinskas

    2011-04-01

    Full Text Available The analyzed questions of information security transferable by the radio connection link are presented in this article. This safety it is especially important for design of unmanned air vehicles (UAV and for other remote control vehicles. Also questions about UAV communication systems structure, security treats of radio connection system, possible menaces for secure information transferring, security and integrity are discussed in our presentation. Article in Lithuanian

  6. Energy efficiency in wireless communication systems

    Science.gov (United States)

    Caffrey, Michael Paul; Palmer, Joseph McRae

    2012-12-11

    Wireless communication systems and methods utilize one or more remote terminals, one or more base terminals, and a communication channel between the remote terminal(s) and base terminal(s). The remote terminal applies a direct sequence spreading code to a data signal at a spreading factor to provide a direct sequence spread spectrum (DSSS) signal. The DSSS signal is transmitted over the communication channel to the base terminal which can be configured to despread the received DSSS signal by a spreading factor matching the spreading factor utilized to spread the data signal. The remote terminal and base terminal can dynamically vary the matching spreading factors to adjust the data rate based on an estimation of operating quality over time between the remote terminal and base terminal such that the amount of data being transmitted is substantially maximized while providing a specified quality of service.

  7. Low-Power Reflective Optical Communication System for Pico- and Nano-Satellites

    Science.gov (United States)

    Sinn, A.; Riel, T.; Deisl, F.; Saathof, R.; Schitter, G.

    2016-09-01

    Pico- and nano-satellites (PNS) are promising options for cost-effective and rapid deployable satellite systems. Due to their small size, the available power and therefore the transmittable data volume is limited. This paper proposes optical communication by means of reflected laser light using a modulating retro-reflector (MRR) for energy efficient optical communication with PNS. No laser source or beam steering assembly is necessary at the satellite, thus allowing a weight and energy efficient communication interface. Existing ground stations (GS) as used for satellite laser ranging (SLR) provide all equipment required for this system. By providing a link budget for communication to PNS in LEOs feasibility is investigated. It is shown that an affordable GS based on small telescopes with diameters below 0.3m in combination with commercial mounts enables the targeted application. A detailed analysis of LCD based MRRs is shown, denoting cost-efficient modulators for reflective optical communication. A data-rate of 2.5kbps at an input power of less than 80 mW is shown in a laboratory setup. Using a high performance sampling circuit and a laser power of only 1mW, a bit error ratio (BER) of below 10e-3 is achieved, successfully demonstrating reflective optical communication as an alternative to current RF based systems.

  8. The RF system for the Accelerator Production of Tritium (APT) Low Energy Demonstration Accelerator (LEDA) at Los Alamos

    Energy Technology Data Exchange (ETDEWEB)

    Lynch, M.T.; Rees, D.; Tallerico, P.; Regan, A. [Accelerator Operations & Technology Division, Los Alamos National Laboratory, Los Alamos, NM (United States)

    1996-09-01

    To develop and demonstrate the crucial front end of the APT accelerator and some of the critical components for APT, Los Alamos is building a CW proton accelerator (LEDA) to provide 100 mA at up to 40 MeV. LEDA will be installed where the SDI-sponsored Ground Test Accelerator was located. The first accelerating structure for LEDA is a 7-MeV RFQ operating at 350 MHz, followed by several stages of a coupled-cavity Drift Tube Linac (CCDTL) operating at 700 MHz. The first stage of LEDA will go to 12 MeV. Higher energies, up to 40 MeV, come later in the program. Three 1.2-MW CW RF systems will be used to power the RFQ. This paper describes the RF systems being assembled for LEDA, including the 350 and 700-MHz klystrons, the High Voltage Power Supplies, transmitters, RF transport, window/coupler assemblies, and controls. Some of the limitations imposed by the schedule and the building itself are addressed.

  9. Optically envelope detected QAM and QPSK RF modulated signals in hybrid wireless-fiber systems

    DEFF Research Database (Denmark)

    Tafur Monroy, Idelfonso; Prince, Kamau; Seoane, Jorge;

    2009-01-01

    from a 1.6 GHz carrier frequency to an IF at 500 MHz, requiring no high frequency local oscillator and mixer at the remote base station. This result proves the feasibility of optical envelope detection for complex modulation formats of RF signals for hybrid wireless-fiber transmission links....

  10. Single bunch injection system for storage ring FEL using an rf photoinjector

    Science.gov (United States)

    O'Shea, P. G.; Lancaster, J. A.; Madey, J. M. J.; Sachtschale, R.; Jones, R.

    1997-05-01

    RF photoinjectors have gained acceptance as the source of choice for high-brightness electron accelerators, but have been quite expensive to build and difficult to operate. In this paper we describe the successful operation of an inexpensive, simple and reliable rf photoinjector suitable for single bunch injection into storage rings. For optimum storage ring FEL and Compton Backscatter performance, we require that the electrons be injected to specified ring rf buckets and no others. The injector-linac electron gun is a single-cell s-band rf gun with a LaB6 cathode. The gun is followed by an a-magnet momentum filter and buncher. The LaB6 cathode can be operated in a pure thermionic mode, a laser switched photoemission mode, or in a combined mode. The laser is a near-UV TEA nitrogen laser with a 600 ps pulse, and 0-50 Hz repetition rate. We routinely inject 0.1 nC bunches at 270 MeV. The ratio of charge in the primary ring bucket to that in the other buckets is better than 1000.

  11. Electron bunch energy and phase feed-forward stabilization system for the Mark V RF-linac free-electron laser.

    Science.gov (United States)

    Hadmack, M R; Jacobson, B T; Kowalczyk, J M D; Lienert, B R; Madey, J M J; Szarmes, E B

    2013-06-01

    An amplitude and phase compensation system has been developed and tested at the University of Hawai'i for the optimization of the RF drive system to the Mark V free-electron laser. Temporal uniformity of the RF drive is essential to the generation of an electron beam suitable for optimal free-electron laser performance and the operation of an inverse Compton scattering x-ray source. The design of the RF measurement and compensation system is described in detail and the results of RF phase compensation are presented. Performance of the free-electron laser was evaluated by comparing the measured effects of phase compensation with the results of a computer simulation. Finally, preliminary results are presented for the effects of amplitude compensation on the performance of the complete system.

  12. RF Design and Predicted Performance for a Future 34-meter Shaped Dual-reflector Antenna System Using the Common Aperture X-S Feedhorn

    Science.gov (United States)

    Williams, W. F.

    1983-01-01

    The Networks Consolidation Program (NCP) will utilize 34-meter shaped dual-reflector Cassegrain antennas. The shaping calculations, the X/S-band feedhorn to be used, and the predicted RF performance of this antenna system are discussed.

  13. Advances in gallium arsenide monolithic microwave integrated-circuit technology for space communications systems

    Science.gov (United States)

    Bhasin, K. B.; Connolly, D. J.

    1986-01-01

    Future communications satellites are likely to use gallium arsenide (GaAs) monolithic microwave integrated-circuit (MMIC) technology in most, if not all, communications payload subsystems. Multiple-scanning-beam antenna systems are expected to use GaAs MMIC's to increase functional capability, to reduce volume, weight, and cost, and to greatly improve system reliability. RF and IF matrix switch technology based on GaAs MMIC's is also being developed for these reasons. MMIC technology, including gigabit-rate GaAs digital integrated circuits, offers substantial advantages in power consumption and weight over silicon technologies for high-throughput, on-board baseband processor systems. In this paper, current developments in GaAs MMIC technology are described, and the status and prospects of the technology are assessed.

  14. Electronic communication channel within the patient data management system improves internal communication in the ICU.

    Science.gov (United States)

    Väisänen, Paula; Holopainen, Jaana

    2006-01-01

    The aim of this study was to improve the internal communication within the intensive care unit of the Kuopio University Hospital. We developed an intranet based internal communication channel within the patient data management system and studied the effectiveness of this system in improving communication in the ICU. The hypothesis was that the communication difficulties caused by the structure of the unit, large personnel and work schedule (three separate shifts) could be reduced by supplementing oral communication by this intranet based system. The results clearly indicate that this type of system can significantly improve communication within our unit.

  15. Seamless integrated network system for wireless communication systems

    NARCIS (Netherlands)

    Wu, Gang; Mizuno, Mitsuhiko; Hase, Yoshihiro; Havinga, Paul J.M.

    2006-01-01

    To create a network that connects a plurality of wireless communication systems to create optimal systems for various environments, and that seamlessly integrates the resulting systems together in order to provide more efficient and advanced service in general. A network system that can seamlessly i

  16. Seamless integrated network system for wireless communication systems

    NARCIS (Netherlands)

    Wu, Gang; Mizuno, Mitsuhiko; Hase, Yoshihiro; Havinga, Paul J.M.

    2002-01-01

    To create a network that connects a plurality of wireless communication systems to create optimal systems for various environments, and that seamlessly integrates the resulting systems together in order to provide more efficient and advanced service in general. A network system that can seamlessly i

  17. Communicating embedded systems software and design

    CERN Document Server

    Jard, Claude

    2013-01-01

    The increased complexity of embedded systems coupled with quick design cycles to accommodate faster time-to-market requires increased system design productivity that involves both model-based design and tool-supported methodologies. Formal methods are mathematically-based techniques and provide a clean framework in which to express requirements and models of the systems, taking into account discrete, stochastic and continuous (timed or hybrid) parameters with increasingly efficient tools. This book deals with these formal methods applied to communicating embedded systems by presenting the

  18. Distributed algorithms over communicating membrane systems.

    Science.gov (United States)

    Ciobanu, Gabriel

    2003-07-01

    This paper presents fundamental distributed algorithms over membrane systems with antiport carriers. We describe distributed algorithms for collecting and dispersing information, leader election in these systems, and the mutual exclusion problem. Finally, we consider membrane systems producing correct results despite some failures at some of the components or the communication links. We show that membrane systems with antiport carriers provide an appropriate model for distributed computing, particularly for message-passing algorithms interpreted here as membrane transport in both directions, namely when two chemicals behave as input and output messages and pass the membranes in both directions using antiport carriers.

  19. Communication System for CIMS Application Integration Platform

    Institute of Scientific and Technical Information of China (English)

    1999-01-01

    CIMS has seen the growth of multiple incompatible hardware architectur es, each architecture supporting several incompatible operating systems, and eac h platform operating with various incompatible development tools (e.g., programm ing language compilers, DBMS, etc.) and one or more incompatible graphic user in terfaces. Also, the growth of the Internet, the World-Wide Web, has introduced new dimensio ns of complexity into the development process. All of these must be dealt with a s the application is made workable in a distributed client-server environment. This paper outlines the architecture of a communication system for the CIMS appl ication integration platform. The communication system makes possible the reque st for service across heterogeneous platforms and networks, and provides some co mmon solutions to issues common to CIMS applications.

  20. Security aspects of RFID communication systems

    Science.gov (United States)

    Bîndar, Valericǎ; Popescu, Mircea; Bǎrtuşicǎ, Rǎzvan; Craciunescu, Razvan; Halunga, Simona

    2015-02-01

    The objective of this study is to provide an overview of basic technical elements and security risks of RFID communication systems and to analyze the possible threats arising from the use of RFID systems. A number of measurements are performed on a communication system including RFID transponder and the tag reader, and it has been determined that the uplink signal level is 62 dB larger than the average value of the noise at the distance of 1m from the tag, therefore the shielding effectiveness has to exceed this threshold. Next, the card has been covered with several shielding materials and measurements were carried, under similar conditions to test the recovery of compromising signals. A very simple protection measure to prevent unauthorized reading of the data stored on the card has been proposed, and some electromagnetic shielding materials have been proposed and tested.

  1. Compositional Memory Systems for Multimedia Communicating Tasks

    CERN Document Server

    Molnos, A M; Cotofana, S D; Van Eijndhoven, J T J

    2011-01-01

    Conventional cache models are not suited for real-time parallel processing because tasks may flush each other's data out of the cache in an unpredictable manner. In this way the system is not compositional so the overall performance is difficult to predict and the integration of new tasks expensive. This paper proposes a new method that imposes compositionality to the system?s performance and makes different memory hierarchy optimizations possible for multimedia communicating tasks when running on embedded multiprocessor architectures. The method is based on a cache allocation strategy that assigns sets of the unified cache exclusively to tasks and to the communication buffers. We also analytically formulate the problem and describe a method to compute the cache partitioning ratio for optimizing the throughput and the consumed power. When applied to a multiprocessor with memory hierarchy our technique delivers also performance gain. Compared to the shared cache case, for an application consisting of two jpeg ...

  2. The ACTS Flight System - Cost-Effective Advanced Communications Technology. [Advanced Communication Technology Satellite

    Science.gov (United States)

    Holmes, W. M., Jr.; Beck, G. A.

    1984-01-01

    The multibeam communications package (MCP) for the Advanced Communications Technology Satellite (ACTS) to be STS-launched by NASA in 1988 for experimental demonstration of satellite-switched TDMA (at 220 Mbit/sec) and baseband-processor signal routing (at 110 or 27.5 Mbit/sec) is characterized. The developmental history of the ACTS, the program definition, and the spacecraft-bus and MCP parameters are reviewed and illustrated with drawings, block diagrams, and maps of the coverage plan. Advanced features of the MPC include 4.5-dB-noise-figure 30-GHz FET amplifiers and 20-GHz TWTA transmitters which provide either 40-W or 8-W RF output, depending on rain conditions. The technologies being tested in ACTS can give frequency-reuse factors as high as 20, thus greatly expanding the orbit/spectrum resources available for U.S. communications use.

  3. NASA Unmanned Aircraft (UA) Control and Non-Payload Communication (CNPC) System Waveform Trade Studies

    Science.gov (United States)

    Chavez, Carlos; Hammel, Bruce; Hammel, Allan; Moore, John R.

    2014-01-01

    Unmanned Aircraft Systems (UAS) represent a new capability that will provide a variety of services in the government (public) and commercial (civil) aviation sectors. The growth of this potential industry has not yet been realized due to the lack of a common understanding of what is required to safely operate UAS in the National Airspace System (NAS). To address this deficiency, NASA has established a project called UAS Integration in the NAS (UAS in the NAS), under the Integrated Systems Research Program (ISRP) of the Aeronautics Research Mission Directorate (ARMD). This project provides an opportunity to transition concepts, technology, algorithms, and knowledge to the Federal Aviation Administration (FAA) and other stakeholders to help them define the requirements, regulations, and issues for routine UAS access to the NAS. The safe, routine, and efficient integration of UAS into the NAS requires new radio frequency (RF) spectrum allocations and a new data communications system which is both secure and scalable with increasing UAS traffic without adversely impacting the Air Traffic Control (ATC) communication system. These data communications, referred to as Control and Non-Payload Communications (CNPC), whose purpose is to exchange information between the unmanned aircraft and the ground control station to ensure safe, reliable, and effective unmanned aircraft flight operation. A Communications Subproject within the UAS in the NAS Project has been established to address issues related to CNPC development, certification and fielding. The focus of the Communications Subproject is on validating and allocating new RF spectrum and data link communications to enable civil UAS integration into the NAS. The goal is to validate secure, robust data links within the allocated frequency spectrum for UAS. A vision, architectural concepts, and seed requirements for the future commercial UAS CNPC system have been developed by RTCA Special Committee 203 (SC-203) in the process

  4. Wavelength-domain RF photonic signal processing

    Science.gov (United States)

    Gao, Lu

    This thesis presents a novel approach to RF-photonic signal processing applications based on wavelength-domain optical signal processing techniques using broadband light sources as the information carriers, such as femtosecond lasers and white light sources. The wavelength dimension of the broadband light sources adds an additional degree of freedom to conventional optical signal processing systems. Two novel wavelength-domain optical signal processing systems are presented and demonstrated in this thesis. The first wavelength-domain RF photonic signal processing system is a wavelength-compensated squint-free photonic multiple beam-forming system for wideband RF phased-array antennas. Such a photonic beam-forming system employs a new modulation scheme developed in this thesis, which uses traveling-wave tunable filters to modulate wideband RF signals onto broadband optical light sources in a frequency-mapped manner. The wavelength dimension of the broadband light sources provides an additional dimension in the wavelength-compensated Fourier beam-forming system for mapping the received RF frequencies to the linearly proportional optical frequencies, enabling true-time-delay beam forming, as well as other novel RF-photonic signal processing functions such as tunable filtering and frequency down conversion. A new slow-light mechanism, the SLUGGISH light, has also been discovered with an effective slow-light velocity of 86 m/s and a record time-bandwidth product of 20. Experimental demonstration of true-time-delay beam forming based on the SLUGGISH light effect has also been presented in this thesis. In the second wavelength-domain RF photonic signal processing system, the wavelength dimension increases the information carrying capacity by spectrally multiplexing multiple wavelength channels in a wavelength-division-multiplexing fiber-optic communication system. A novel ultrafast all-optical 3R (Re-amplification, Retiming, Re-shaping) wavelength converter based on

  5. Design of short-range wireless transmission system based on PIC16F726 and nRF24L01%基于PIC16F726和nRF24L01的短距离无线传输系统设计

    Institute of Scientific and Technical Information of China (English)

    张肖汉; 陈以; 李明伟

    2012-01-01

    In order to meet the market demand of short-range wireless communication, using the PIC16F726 and nRF24L01 chip to design short-range wireless transmission system, and this paper also presents the hardware design and software design processes. The test results show that the system has achieved a two-way communication and has got reliable performance , which is strong practical as well as cost-effective.%为了满足当前短距离无线通信的市场需求,采用PIC16F726和nRF24L01芯片设计短距离无线传输系统,给出了硬件设计方案和软件设计流程。测试结果表明,系统实现了双向通信,性能稳定可靠,实用性强,性价比高。

  6. Klystron Linearizer for Use with 1.2 MW 476 MHz Klystrons in PEP-II RF Systems

    CERN Document Server

    Fox, John; Mastorides, Themis; Teytelman, Dmitry; Van Winkle, Daniel; Zhou, Yubo

    2005-01-01

    The direct and comb loop feedback around the RF cavities in PEP-II is critical in reducing longitudinal instabilities driven by the cavity impedance, and the non-linear 1 MW klystron is in the signal path for these feedback loops. As a result, the effective small-signal gain of the klystron at 85% saturation reduces the impedance control by factors of 5 to 20 as compared to a linear power amplifier. A klystron linearizer circuit has been developed which operates in series with the power amplifier and acts to equalize the small and large signal gains through the combination. The technique must implement a 1 MHz linear control bandwidth over roughly 15 dB of RF signal level variation. The dynamics of this system is operating point dependent, and the channel must have dynamic gain compensation to keep the linearity compensation loop stable over changes in operating point. The design of this non-linear signal processing channel (incorporating RF and DSP techniques) and measured results from full-power klystron te...

  7. Design and RF measurements of a 5 GHz 500 kW window for the ITER LHCD system

    CERN Document Server

    Hillairet, Julien; Dechambre, N; Delpech, L; Ekedahl, A; Faure, N; Goniche, M; Kim, J; Larroque, S; Magne, R; Marfisi, L; Namkung, W; Park, H; Park, S; Poli, S; Vulliez, K

    2015-01-01

    CEA/IRFM is conducting R\\&D efforts in order to validate the critical RF components of the 5 GHz ITER LHCD system, which is expected to transmit 20 MW of RF power to the plasma. Two 5 GHz 500 kW BeO pill-box type window prototypes have been manufactured in 2012 by the PMB Company, in close collaboration with CEA/IRFM. Both windows have been validated at low power, showing good agreement between measured and modeling, with a return loss better than 32 dB and an insertion loss below 0.05 dB. This paper reports on the window RF design and the low power measurements. The high power tests up to 500kW have been carried out in March 2013 in collaboration with NFRI. Results of these tests are also reported. In the current ITER LHCD design, 20 MW Continuous Wave (CW) of Radio-Frequency power at 5 GHz are expected to be generated and transmitted to the plasma. In order to separate the vacuum vessel pressure from the cryostat waveguide pressure, forty eight 5 GHz 500kW CW windows are to be assembled on the waveguide...

  8. Simulation and characterization of the RF system and global stability analysis at the REGAE linear electron accelerator

    Energy Technology Data Exchange (ETDEWEB)

    Mayet, Frank

    2012-12-15

    LAOLA (LAboratory for Laser- and beam-driven plasma Acceleration), is a collaboration between groups from DESY and the University of Hamburg. Its mission is to complement basic research in the relatively new field of plasma wakefield acceleration (PWA) by an explicit combination with DESY's conventional, modern accelerators. The linear electron accelerator REGAE is designed to produce sub 10 fs low charge electron bunches with ultra-low emittance at a repetition rate of 50 Hz. The planned experiments include femtosecond electron diffraction (R.J. Dwayne Miller), as well as the probing of laser induced plasma wakefields with well characterized bunches (LAOLA). They all require high bunch time of flight stability down to 10 fs. The REGAE machine consists of two RF cavities, both fed by a single klystron. While the first one - the gun cavity - is used for acceleration of the electrons, the second one - the buncher cavity - can be used to reduce the electron bunch length. This scheme only works for a specific RF phase relation between the two cavities. This thesis is split into two parts. In the first one the implications of the unique two cavity design on day-to-day machine operation are analyzed. To this end an analytical model of the RF system is developed, which is necessary for understanding how to individually adjust the cavity phases. In the second part the influence of the setup on time of flight stability is discussed with an emphasis on phase jitter compensation. RF phase stability measurements reveal that the current machine setup allows for a time of flight stability down to 50 fs right after the gun.

  9. A wireless electrocardiosignal acquisition system based on nRF24L01%基于nRF24L01的无线心电采集系统的设计

    Institute of Scientific and Technical Information of China (English)

    姚湘陵; 秦实宏; 袁发庭

    2013-01-01

    An ECG collection system is desiqned based on nRF24L01. The system use a series of analog circuits to adjust and sample heart signals, which is composed of pre-amplification circuit, band-pass filter circuit, main amplifier circuit, trap circuit, electrical level rising circuit The adjusted heart signals are transmitted to PC by nRF24L01 which is a novel wireless transmission module so as to observe heart rate change more convenient%设计了一种基于nRF24L01的无线心电采集系统,该系统采用模拟集成电路对心电信号进行调理和采样,通过前置放大电路、带通滤波电路、主放大电路、50 Hz陷波电路、电平抬升电路等电路调理心电信号后,使用无线传输模块nRF24L01将心电信号发送至上位机中显示,从而达到通过PC显示和监测心律变化的目的.

  10. Communications System for Down-Hole Measurements

    Directory of Open Access Journals (Sweden)

    Mijarez-Castro Rito

    2013-12-01

    Full Text Available Progressively deeper and hotter oil wells have driven design modification that enhances the performance in sensors and downhole electronic instruments. Oil reservoirs in Mexico are located at mean depths of 6,000 m; as a consequence, the requirements for measuring thermodynamic and geophysical parameters are challenging. This paper describes a bidirectional communication system that exchanges data from a down-hole high pressure and high temperature (HP/HT measurement tool to the surface installation. The communication medium is a 7 km mono-conductor 1K22 logging cable used also as a power supply transmission line. The system consists of a proprietary downhole measurement tool, composed of a HT/HP sensor and a high temperature DSP-based electronic device, and a data acquisition equipment located in the surface installation. The system employs a communication algorithm that automatically changes the carrier frequency of the modulation technique employed, to avoid issues derived from noise interference, cable attenuation and thermal drift of the front end passive elements. The laboratory tests results provide a firm basis for testing and evaluating the system in the field.

  11. RESULTS FROM A DEMONSTRATION OF RF-BASED UF6 CYLINDER ACCOUNTING AND TRACKING SYSTEM INSTALLED AT A USEC FACILITY

    Energy Technology Data Exchange (ETDEWEB)

    Pickett, Chris A [ORNL; Kovacic, Donald N [ORNL; Morgan, Jim [Innovative Solutions; Younkin, James R [ORNL; Carrick, Bernie [USEC, Inc.; Ken, Whittle [USEC, Inc.; Johns, R E [Pacific Northwest National Laboratory (PNNL)

    2008-09-01

    Approved industry-standard cylinders are used globally for storing and transporting uranium hexafluoride (UF{sub 6}) at uranium enrichment plants and processing facilities. To verify that no diversion or undeclared production of nuclear material involving UF{sub 6} cylinders at the facility has occurred, the International Atomic Energy Agency (IAEA) conducts periodic, labor-intensive physical inspections to validate facility records, cylinder identities, and cylinder weights. A reliable cylinder monitoring system that would improve overall inspector effectiveness would be a significant improvement to the current international safeguards inspection regime. Such a system could include real-time unattended monitoring of cylinder movements, situation-specific rules-based event detection algorithms, and the capability to integrate with other types of safeguards technologies. This type of system could provide timely detection of abnormal operational activities that may be used to ensure more appropriate and efficient responses by the IAEA. A system of this type can reduce the reliance on paper records and have the additional benefit of facilitating domestic safeguards at the facilities at which it is installed. A radio-frequency (RF)-based system designed to track uranium hexafluoride (UF{sub 6}) cylinders during processing operations was designed, assembled, and tested at the United States Enrichment Corporation (USEC) facility in Portsmouth, Ohio, to determine the operational feasibility and durability of RF technology. The overall objective of the effort was to validate the robustness of RF technology for potential use as a future international safeguards tool for tracking UF6 cylinders at uranium-processing facilities. The results to date indicate that RF tags represent a feasible technique for tracking UF{sub 6} cylinders in operating facilities. Additional work will be needed to improve the operational robustness of the tags for repeated autoclave processing and to

  12. Installation and Commissioning of CYCIAE-100 RF Cavity

    Institute of Scientific and Technical Information of China (English)

    JI; Bin; XING; Jian-sheng; LIU; Geng-shou; YIN; Zhi-guo; ZHANG; Tian-jue; LEI; Yu; FU; Xiao-liang; LI; Peng-zhan; LV; Yin-long; ZHU; Peng-fei; FU; Li-cheng; LIU; Jie; ZHANG; De-zhi; CUI; Bai-yao; DONG; Huan-jun; WANG; Zhen-hui

    2013-01-01

    The RF cavity is used to establish electrical field for the particle acceleration in the cyclotron,the stability of the RF cavity affects the RF system directly.A RF cavity with high quality can reduce thepower consumption of the RF system and make the cooling system simple.A good design is the first step towards RF cavity with high quality.The installation and commissioning are the next important process to achieve an excellent performance.The height of the

  13. Coding the Beams: Improving Beamforming Training in mmWave Communication System

    CERN Document Server

    Tsang, Y Ming; Addepalli, Sateesh

    2011-01-01

    The mmWave communication system is operating at a regime with high number of antennas and very limited number of RF analog chains. Large number of antennas are used to extend the communication range for recovering the high path loss while fewer RF analog chains are designed to reduce transmit and processing power and hardware complexity. In this regime, typical MIMO algorithms are not applicable. Before any communication starts, devices are needed to align their beam pointing angles towards each other. An efficient searching protocol to obtain the best beam angle pair is therefore needed. It is called BeamForming (BF) training protocol. This paper presents a fast BF training protocol called beam coding. Each beam angle is assigned unique signature code. By coding multiple beam angles and steering at their angles simultaneously in a training packet, the best beam angle pair can be obtained in a few packets. This faster BF training protocol not only shows the robustness in non-line-of-sight, multi-user and movi...

  14. AN OVERVIEW OF VISIBLE LIGHT COMMUNICATION SYSTEMS

    Directory of Open Access Journals (Sweden)

    Taner Cevik

    2015-11-01

    Full Text Available Visible Light Communication (VLC has gained great interest in the last decade due to the rapid developments in Light Emitting Diodes (LEDs fabrication. Efficiency, durability and long life span of LEDs make them a promising residential lighting equipment as well as an alternative cheap and fast data transfer equipment. Appliance of visual light in data communication by means of LEDs has been densely searched in academia. In this paper, we explore the fundamentals and challenges of indoor VLC systems. Basics of optical transmission such as transmitter, receiver, and links are investigated. Moreover, characteristics of channel models in indoor VLC systems are identified and theoretical details about channel modelling are presented in detail.

  15. Toward a Gigabit Wireless Communications System

    CERN Document Server

    Rakotondrainibe, Lahatra; Zaharia, Gheorghe; Zein, Ghaïs El

    2009-01-01

    This paper presents the design and the realization of a hybrid wireless Gigabit Ethernet indoor communications system operating at 60 GHz. As the 60 GHz radio link operates only in a single-room configuration, an additional Radio over Fiber (RoF) link is used to ensure the communications within all the rooms of a residential environment. The system uses low complexity baseband processing modules. A byte synchronization technique is designed to provide a high value of the preamble detection probability and a very small value of the false detection probability. Conventional RS (255, 239) encoder and decoder are used for channel forward error correction (FEC). The FEC parameters are determined by the tradeoff between higher coding gain and hardware complexity. The results of bit error rate measurements at 875 Mbps are presented for various antennas configurations.

  16. Radio propagation for space communications systems

    Science.gov (United States)

    Ippolito, L. J.

    1981-01-01

    This paper presents a review of the most recent information on the effects of the earth's atmosphere on space communications systems. Models and techniques used in the prediction of atmospheric effects as influenced by frequency, geography, elevation angle, and type of transmission are discussed. Recent data on performance characteristics obtained from direct measurements on satellite links operating to above 30 GHz are reviewed. Particular emphasis is placed on the effects of precipitation on the earth-space path, including rain attenuation, and rain and ice-particle depolarization. Sky noise, antenna gain degradation, scintillations, and bandwidth coherence are also discussed. The impact of the various propagation factors on communications system design criteria is presented. These criteria include link reliability, power margins, noise contributions, modulation and polarization factors, channel crosstalk, error-rate, and bandwidth limitations.

  17. ISR RF cavities

    CERN Multimedia

    1983-01-01

    In each ISR ring the radiofrequency cavities were installed in one 9 m long straight section. The RF system of the ISR had the main purpose to stack buckets of particles (most of the time protons)coming from the CPS and also to accelerate the stacked beam. The installed RF power per ring was 18 kW giving a peak accelerating voltage of 20 kV. The system had a very fine regulation feature allowing to lower the voltage down to 75 V in a smooth and well controlled fashion.

  18. Remote RF Battery Charging

    NARCIS (Netherlands)

    Visser, H.J.; Pop, V.; Op het Veld, J.H.G.; Vullers, R.J.M.

    2011-01-01

    The design of a remote RF battery charger is discussed through the analysis and design of the subsystems of a rectenna (rectifying antenna): antenna, rectifying circuit and loaded DC-to-DC voltage (buck-boost) converter. Optimum system power generation performance is obtained by adopting a system in

  19. Ship-Shore Packet Switched Communications System.

    Science.gov (United States)

    1986-06-01

    a fatal flaw for sea service communications. This instability is described in several texts [ Stallings , 85; Tanenbaum, 81]. 68 b. Token Systems Again... decompressor in the data path. otherwise, the decompression algorithm would compound errors and make different instances of errored packets different lengths...Further detail may be found in several sources including listed references [ Stallings , 85]. DoD’s seminal ARPANET work predated the ISO model and evolved a

  20. Electronic circuits for communications systems: A compilation

    Science.gov (United States)

    1972-01-01

    The compilation of electronic circuits for communications systems is divided into thirteen basic categories, each representing an area of circuit design and application. The compilation items are moderately complex and, as such, would appeal to the applications engineer. However, the rationale for the selection criteria was tailored so that the circuits would reflect fundamental design principles and applications, with an additional requirement for simplicity whenever possible.