Project management plan for Project W-320, Tank 241-C-106 sluicing. Revision 2

International Nuclear Information System (INIS)

Phillips, D.R.

1994-07-01

A major mission of the US Department of Energy (DOE) is the permanent disposal of Hanford Site defense wastes by utilizing safe, environmentally acceptable, and cost-effective disposal methods that meet applicable regulations. The Tank Waste Remediation System (TWRS) Program was established at the Hanford Site to manage and control activities specific to the remediation of safety watch list tanks, including high-heat-producing tanks, and for the ultimate characterization, retrieval, pretreatment, and disposal of the low- and high-level fractions of the tank waste. Project W-320, Tank 241-C-106 Sluicing, provides the methodology, equipment, utilities, and facilities necessary for retrieving the high-heat waste from single-shell tank (SST) 24-C-106. Project W-320 is a fiscal year (FY) 1993 expense-funded major project, and has a design life of 2 years. Retrieval of the waste in tank 241-C-106 will be accomplished through mobilization of the sludge into a pumpable slurry using past-practice sluicing. The waste is then transferred directly to a double-shell tank for interim storage, subsequent pretreatment, and eventual disposal. A detailed description of the management organization and responsibilities of all participants is presented in this document

Operational tank leak detection and minimization during retrieval

International Nuclear Information System (INIS)

Hertzel, J.S.

1996-03-01

This report evaluates the activities associated with the retrieval of wastes from the single-shell tanks proposed under the initial Single-Shell Tank Retrieval System. This report focuses on minimizing leakage during retrieval by using effective leak detection and mitigating actions. After reviewing the historical data available on single-shell leakage, and evaluating current leak detection technology, this report concludes that the only currently available leak detection method which can function within the most probable leakage range is the mass balance system. If utilized after each sluicing campaign, this method should allow detection at a leakage value well below the leakage value where significant health effects occur which is calculated for each tank. Furthermore, this report concludes that the planned sequence or sluicing activities will serve to further minimize the probability and volume of leaks by keeping liquid away from areas with the greatest potential for leaking. Finally, this report identifies a series of operational responses which when used in conjunction with the recommended sluicing sequence and leak detection methods will minimize worker exposure and environmental safety health risks

Hanford Tanks Initiative fiscal year 1997 retrieval technology demonstrations

International Nuclear Information System (INIS)

Berglin, E.J.

1998-01-01

The Hanford Tanks Initiative was established in 1996 to address a range of retrieval and closure issues associated with radioactive and hazardous waste stored in Hanford's single shell tanks (SSTs). One of HTI's retrieval goals is to ''Successfully demonstrate technology(s) that provide expanded capabilities beyond past practice sluicing and are extensible to retrieve waste from other SSTS.'' Specifically, HTI is to address ''Alternative technologies to past practice sluicing'' ... that can ... ''successfully remove the hard heel from a sluiced tank or to remove waste from a leaking SST'' (HTI Mission Analysis). During fiscal year 1997, the project contracted with seven commercial vendor teams to demonstrate retrieval technologies using waste simulants. These tests were conducted in two series: three integrated tests (IT) were completed in January 1997, and four more comprehensive Alternative Technology Retrieval Demonstrations (ARTD) were completed in July 1997. The goal of this testing was to address issues to minimize the risk, uncertainties, and ultimately the overall cost of removing waste from the SSTS. Retrieval technologies can be separated into three tracks based on how the tools would be deployed in the tank: globally (e.g., sluicing) or using vehicles or robotic manipulators. Accordingly, the HTI tests included an advanced sluicer (Track 1: global systems), two different vehicles (Track 2: vehicle based systems), and three unique manipulators (Track 3: arm-based systems), each deploying a wide range of dislodging tools and conveyance systems. Each industry team produced a system description as envisioned for actual retrieval and a list of issues that could prevent using the described system; defined the tests to resolve the issues; performed the test; and reported the results, lessons learned, and state of issue resolution. These test reports are cited in this document, listed in the reference section, and summarized in the appendices. This report

Hanford Tanks Initiative fiscal year 1997 retrieval technology demonstrations

Energy Technology Data Exchange (ETDEWEB)

Berglin, E.J.

1998-02-05

The Hanford Tanks Initiative was established in 1996 to address a range of retrieval and closure issues associated with radioactive and hazardous waste stored in Hanford`s single shell tanks (SSTs). One of HTI`s retrieval goals is to ``Successfully demonstrate technology(s) that provide expanded capabilities beyond past practice sluicing and are extensible to retrieve waste from other SSTS.`` Specifically, HTI is to address ``Alternative technologies to past practice sluicing`` ... that can ... ``successfully remove the hard heel from a sluiced tank or to remove waste from a leaking SST`` (HTI Mission Analysis). During fiscal year 1997, the project contracted with seven commercial vendor teams to demonstrate retrieval technologies using waste simulants. These tests were conducted in two series: three integrated tests (IT) were completed in January 1997, and four more comprehensive Alternative Technology Retrieval Demonstrations (ARTD) were completed in July 1997. The goal of this testing was to address issues to minimize the risk, uncertainties, and ultimately the overall cost of removing waste from the SSTS. Retrieval technologies can be separated into three tracks based on how the tools would be deployed in the tank: globally (e.g., sluicing) or using vehicles or robotic manipulators. Accordingly, the HTI tests included an advanced sluicer (Track 1: global systems), two different vehicles (Track 2: vehicle based systems), and three unique manipulators (Track 3: arm-based systems), each deploying a wide range of dislodging tools and conveyance systems. Each industry team produced a system description as envisioned for actual retrieval and a list of issues that could prevent using the described system; defined the tests to resolve the issues; performed the test; and reported the results, lessons learned, and state of issue resolution. These test reports are cited in this document, listed in the reference section, and summarized in the appendices. This report

Safety equipment list for 241-C-106 waste retrieval, Project W-320: Revision 1

International Nuclear Information System (INIS)

Conner, J.C.

1994-01-01

The goals of the C-106 sluicing operation are: (1) to stabilize the tank by reducing the heat load in the tank to less than 42 MJ/hr (40,000 Btu/hour), and (2) to initiate demonstration of single-shell tank (SST) retrieval technology. The purpose of this supporting document (SD) is as follows: (1) to provide safety classifications for items (systems, structures, equipment, components, or parts) for the waste retrieval sluicing system (WRSS), and (2) to document and methodology used to develop safety classifications. Appropriate references are made with regard to use of existing systems, structures, equipments, components, and parts for C-106 single-shell transfer tank located in the C Tank Farm, and 241-AY-102 (AY-102) double shell receiver tanks (DST) located in the Aging Waste Facility (AWF). The Waste Retrieval Sluicing System consists of two transfer lines that would connect the two tanks, one to carry the sluiced waste slurry to AY-102, and the other to return the supernatant liquid to C-106. The supernatant, or alternate fluid, will be used to mobilize waste in C-106 for the sluicing process. The equipment necessary for the WRSS include pumps in each tank, sluicers to direct the supernatant stream in C-106, a slurry distributor in AY-102, HVAC for C-106, instrumentation and control devices, and other existing components as required

Remote systems for waste retrieval from the Oak Ridge National Laboratory gunite tanks

International Nuclear Information System (INIS)

Falter, D.D.; Babcock, S.M.; Burks, B.L.; Lloyd, P.D.; Randolph, J.D.; Rutenber, J.E.; Van Hoesen, S.D.

1995-01-01

As part of a Comprehensive Environmental Response, Compensation, and Liability Act Treatability Study funded by the Department of Energy, the Oak Ridge National Laboratory (ORNL) is preparing to demonstrate and evaluate two approaches for the remote retrieval of wastes in underground storage tanks. This work is being performed to identify the most cost-effective and efficient method of waste removal before full-scale remediation efforts begin in 1998. System requirements are based on the need to dislodge and remove sludge wastes ranging in consistency from broth to compacted clay from Gunite (Shotcrete) tanks that are approaching fifty years in age. Systems to be deployed must enter and exit through the existing 0.6 m (23.5 in.) risers and conduct retrieval operations without damaging the layered concrete walls of the tanks. Goals of this project include evaluation of confined sluicing techniques and successful demonstration of a telerobotic arm-based system for deployment of the sluicing system. As part of a sister project formed on the Old Hydrofracture Facility tanks at ORNL, vehicle-based tank remediation will also be evaluated

Antecedent Selection for Sluicing

DEFF Research Database (Denmark)

Anand, Pranav; Hardt, Daniel

2016-01-01

Sluicing is an elliptical process where the majority of a question can go unpronounced as long as there is a salient antecedent in previous discourse. This paper considers the task of antecedent selection: finding the correct antecedent for a given case of sluicing. We argue that both syntactic...... and discourse relationships are important in antecedent selection, and we construct linguistically sophisticated features that describe the relevant relationships. We also define features that describe the relation of the content of the antecedent and the sluice type. We develop a linear model which achieves...... accuracy of 72.4%, a substantial improvement over a strong manually constructed baseline. Feature analysis confirms that both syntactic and discourse features are important in antecedent selection....

Project W-320, 241-C-106 sluicing: Construction specification W-320-C1

International Nuclear Information System (INIS)

Bailey, J.W.

1998-01-01

Project W-320, Waste Retrieval Sluicing System (WRSS), specification is for procurement, fabrication and installation of equipment at the C Tank Farm, including Operator Station and some equipment just outside the C Tank Farm fence, necessary to support the sluicing operation. Work consists of furnishing labor, equipment, and materials to provide the means to procure materials and equipment, fabricate items, excavate and place concrete, and install equipment, piping, wiring, and structures in accordance with the Contract Documents. Major work elements include: Excavation for process and fire protection piping, electrical conduit trenches, and foundations for small structures; Placement of concrete cover blocks, foundations, and equipment pads; Procurement and installation of double walled piping, electrical conduit, fire and raw water piping, chilled water piping, and electrical cable; Procurement and installation of above-ground ventilation system piping between the (HVAC) Process building and Tank C-106; Core drill existing concrete; Furnish and installation of electrical distribution equipment; Installation of the concrete foundation, and assembly installation of the two Seismic Shutdown Systems with Environmental Enclosures; Fabrication and installation of in-pit pipe jumpers, including related valves, instruments and wiring; and Installation of a vertical submersible pump, horizontal booster pump, and winch assembly into tank access riser pits

Innovative technology summary report: Confined sluicing end effector

International Nuclear Information System (INIS)

1998-09-01

A Confined Sluicing End-Effector (CSEE) was field tested during the summer of 1997 in Tank W-3, one of the Gunite and Associated Tanks (GAAT) at the Oak Ridge Reservation (ORR). It should be noted that the specific device used at the Oak Ridge Reservation demonstration was the Sludge Retrieval End-Effector (SREE), although in common usage it is referred to as the CSEE. Deployed by the Modified Light-Duty Utility Arm (MLDUA) and the Houdini remotely operated vehicle (ROV), the CSEE was used to mobilize and retrieve waste from the tank. After removing the waste, the CSEE was used to scarify the gunite walls of Tank W-3, removing approximately 0.1 in of material. The CSEE uses three rotating water-jets to direct a short-range pressurized jet of water to effectively mobilize the waste. Simultaneously, the water and dislodged tank waste, or scarified materials, are aspirated using a water-jet pump-driven conveyance system. The material is then pumped outside of the tank, where it can be stored for treatment. The technology, its performance, uses, cost, and regulatory issues are discussed

Survey package: Technical and contracting strategies for single-shell tank waste retrieval on the Hanford Site

International Nuclear Information System (INIS)

Ramsower, D.C.

1995-01-01

Westinghouse Hanford Company is interested in innovative, commercially available or adaptable retrieval system equipment, concepts, and contracting strategies that will ad to existing Hanford Site technology and significantly reduce cost and/or risk from the baseline retrieval approach of sluicing (hydraulically mining) the waste from the SSTs onsite. The objective of this request is to gather information from industry to identify and summarize a suite of retrieval-related components, systems, and contracting approaches. This information will be used to ensure that WHC understands the various waste retrieval alternative approaches, their risks, and their application on the Hanford Site tanks for those occasions when sluicing is not sufficiently effective, appropriate, or cost-effective. An additional objective is to facilitate industry's understanding of the tank and site interface requirements for SST waste retrieval and the complex statutory, legal, regulatory, labor, and other institutional standards being applied to the Hanford Site. This effort will identify and summarize retrieval solutions by the end of September 1996 so that a clear basis for future retrieval program decisions can be established

Preliminary safety evaluation for 241-C-106 waste retrieval, project W-320

International Nuclear Information System (INIS)

Conner, J.C.

1994-01-01

This document presents the Preliminary Safety Evaluation for Project W-320, Tank 241-C-106 Waste Retrieval Sluicing System (WRSS). The US DOE has been mandated to develop plans for response to safety issues associated with the waste storage tanks at the Hanford Site, and to report the progress of implementing those plans to Congress. The objectives of Project W-230 are to design, fabricate, develop, test, and operate a new retrieval system capable of removing a minimum of about 75% of the high-heat waste contained in C-106. It is anticipated that sluicing operations can remove enough waste to reduce the remaining radiogenic heat load to levels low enough to resolve the high-heat safety issue as well as allow closure of the tank safety issue

Project W-320, 241-C-106 sluicing: Construction specification W-320-C2

International Nuclear Information System (INIS)

Bailey, J.W.

1998-01-01

This supporting document has been prepared to make the construction specifications for Project W-320 readily available. Project W-320, Waste Retrieval Sluicing System (WRSS), specification is for procurement, fabrication and installation of equipment at the C Tank Farm, including Operator Station and some equipment just outside the C Tank Farm fence, necessary to support the sluicing operation. Work consists of furnishing labor, equipment, and materials to provide the means to procure materials and equipment, fabricate items, excavate and place concrete, and install equipment, piping, wiring, and structures in accordance with the Contract Documents. Major work elements include: Excavation for process and fire protection piping, electrical conduit trenches, and foundations for small structures; Placement of concrete cover blocks, foundations, and equipment pads; Procurement and installation of double walled piping, electrical conduit, fire and raw water piping, chilled water piping, and electrical cable; Procurement and installation of above-ground ventilation system piping between the (HVAC) Process building and Tank C-106; Core drill existing concrete; Furnish and installation of electrical distribution equipment; Installation of the concrete foundation, and assembly installation of the two Seismic Shutdown Systems with Environmental Enclosures; Fabrication and installation of in-pit pipe jumpers, including related valves, instruments and wiring; and Installation of a vertical submersible pump, horizontal booster pump, and winch assembly into tank access riser pits

Project W-320, 241-C-106 sluicing: Construction specification W-320-C2

Energy Technology Data Exchange (ETDEWEB)

Bailey, J.W.

1998-07-20

This supporting document has been prepared to make the construction specifications for Project W-320 readily available. Project W-320, Waste Retrieval Sluicing System (WRSS), specification is for procurement, fabrication and installation of equipment at the C Tank Farm, including Operator Station and some equipment just outside the C Tank Farm fence, necessary to support the sluicing operation. Work consists of furnishing labor, equipment, and materials to provide the means to procure materials and equipment, fabricate items, excavate and place concrete, and install equipment, piping, wiring, and structures in accordance with the Contract Documents. Major work elements include: Excavation for process and fire protection piping, electrical conduit trenches, and foundations for small structures; Placement of concrete cover blocks, foundations, and equipment pads; Procurement and installation of double walled piping, electrical conduit, fire and raw water piping, chilled water piping, and electrical cable; Procurement and installation of above-ground ventilation system piping between the (HVAC) Process building and Tank C-106; Core drill existing concrete; Furnish and installation of electrical distribution equipment; Installation of the concrete foundation, and assembly installation of the two Seismic Shutdown Systems with Environmental Enclosures; Fabrication and installation of in-pit pipe jumpers, including related valves, instruments and wiring; and Installation of a vertical submersible pump, horizontal booster pump, and winch assembly into tank access riser pits.

Project W-320, 241-C-106 sluicing: Construction specification W-320-C6

International Nuclear Information System (INIS)

Bailey, J.W.

1998-01-01

This supporting document has been prepared to make the construction specifications for Project W-320 readily available. Project W-320, Waste Retrieval Sluicing System (WRSS), specification is for procurement, fabrication and installation of equipment at the C Tank Farm, including Operator Station and some equipment just outside the C Tank Farm fence, necessary to support the sluicing operation. Work consists of furnishing labor, equipment, and materials to provide the means to procure materials and equipment, fabricate items, excavate and place concrete, and install equipment, piping, wiring, and structures in accordance with the Contract Documents. Major work elements include: Excavation for process and fire protection piping, electrical conduit trenches, and foundations for small structures; Placement of concrete cover blocks, foundations, and equipment pads; Procurement and installation of double walled piping, electrical conduit, fire and raw water piping, chilled water piping, and electrical cable; Procurement and installation of above-ground ventilation system piping between the (HVAC) Process building and Tank C-106; Core drill existing concrete; Furnish and installation of electrical distribution equipment; Installation of the concrete foundation, and assembly installation of the two Seismic Shutdown Systems with Environmental Enclosures; Fabrication and installation of in-pit pipe jumpers, including related valves, instruments and wiring; and Installation of a vertical submersible pump, horizontal booster pump, and winch assembly into tank access riser pits

Project W-320, 241-C-106 sluicing: Construction specification W-320-C5

International Nuclear Information System (INIS)

Bailey, J.W.

1998-01-01

This supporting document has been prepared to make the construction specifications for Project W-320 readily available. Project W-320, Waste Retrieval Sluicing System (WRSS), specification is for procurement, fabrication and installation of equipment at the C Tank Farm, including Operator Station and some equipment just outside the C Tank Farm fence, necessary to support the sluicing operation. Work consists of furnishing labor, equipment, and materials to provide the means to procure materials and equipment, fabricate items, excavate and place concrete, and install equipment, piping, wiring, and structures in accordance with the Contract Documents. Major work elements include: Excavation for process and fire protection piping, electrical conduit trenches, and foundations for small structures; Placement of concrete cover blocks, foundations, and equipment pads; Procurement and installation of double walled piping, electrical conduit, fire and raw water piping, chilled water piping, and electrical cable; Procurement and installation of above-ground ventilation system piping between the (HVAC) Process building and Tank C-106; Core drill existing concrete; Furnish and installation of electrical distribution equipment; Installation of the concrete foundation, and assembly installation of the two Seismic Shutdown Systems with Environmental Enclosures; Fabrication and installation of in-pit pipe jumpers, including related valves, instruments and wiring; and Installation of a vertical submersible pump, horizontal booster pump, and winch assembly into tank access riser pits

Project W-320, 241-C-106 sluicing: Construction specification W-320-C7

International Nuclear Information System (INIS)

Bailey, J.W.

1998-01-01

This supporting document has been prepared to make the construction specifications for Project W-320 readily available. Project W-320, Waste Retrieval Sluicing System (WRSS), specification is for procurement, fabrication and installation of equipment at the C Tank Farm, including Operator Station and some equipment just outside the C Tank Farm fence, necessary to support the sluicing operation. Work consists of furnishing labor, equipment, and materials to provide the means to procure materials and equipment, fabricate items, excavate and place concrete, and install equipment, piping, wiring, and structures in accordance with the Contract Documents. Major work elements include: Excavation for process and fire protection piping, electrical conduit trenches, and foundations for small structures; Placement of concrete cover blocks, foundations, and equipment pads; Procurement and installation of double walled piping, electrical conduit, fire and raw water piping, chilled water piping, and electrical cable; Procurement and installation of above-ground ventilation system piping between the (HVAC) Process building and Tank C-106; Core drill existing concrete; Furnish and installation of electrical distribution equipment; Installation of the concrete foundation, and assembly installation of the two Seismic Shutdown Systems with Environmental Enclosures; Fabrication and installation of in-pit pipe jumpers, including related valves, instruments and wiring; and Installation of a vertical submersible pump, horizontal booster pump, and winch assembly into tank access riser pits

Project W-320, 241-C-106 sluicing: Construction specification W-320-C5

Energy Technology Data Exchange (ETDEWEB)

Bailey, J.W.

1998-07-20

This supporting document has been prepared to make the construction specifications for Project W-320 readily available. Project W-320, Waste Retrieval Sluicing System (WRSS), specification is for procurement, fabrication and installation of equipment at the C Tank Farm, including Operator Station and some equipment just outside the C Tank Farm fence, necessary to support the sluicing operation. Work consists of furnishing labor, equipment, and materials to provide the means to procure materials and equipment, fabricate items, excavate and place concrete, and install equipment, piping, wiring, and structures in accordance with the Contract Documents. Major work elements include: Excavation for process and fire protection piping, electrical conduit trenches, and foundations for small structures; Placement of concrete cover blocks, foundations, and equipment pads; Procurement and installation of double walled piping, electrical conduit, fire and raw water piping, chilled water piping, and electrical cable; Procurement and installation of above-ground ventilation system piping between the (HVAC) Process building and Tank C-106; Core drill existing concrete; Furnish and installation of electrical distribution equipment; Installation of the concrete foundation, and assembly installation of the two Seismic Shutdown Systems with Environmental Enclosures; Fabrication and installation of in-pit pipe jumpers, including related valves, instruments and wiring; and Installation of a vertical submersible pump, horizontal booster pump, and winch assembly into tank access riser pits.

Project W-320, 241-C-106 sluicing: Construction specification W-320-C7

Energy Technology Data Exchange (ETDEWEB)

Bailey, J.W.

1998-07-20

This supporting document has been prepared to make the construction specifications for Project W-320 readily available. Project W-320, Waste Retrieval Sluicing System (WRSS), specification is for procurement, fabrication and installation of equipment at the C Tank Farm, including Operator Station and some equipment just outside the C Tank Farm fence, necessary to support the sluicing operation. Work consists of furnishing labor, equipment, and materials to provide the means to procure materials and equipment, fabricate items, excavate and place concrete, and install equipment, piping, wiring, and structures in accordance with the Contract Documents. Major work elements include: Excavation for process and fire protection piping, electrical conduit trenches, and foundations for small structures; Placement of concrete cover blocks, foundations, and equipment pads; Procurement and installation of double walled piping, electrical conduit, fire and raw water piping, chilled water piping, and electrical cable; Procurement and installation of above-ground ventilation system piping between the (HVAC) Process building and Tank C-106; Core drill existing concrete; Furnish and installation of electrical distribution equipment; Installation of the concrete foundation, and assembly installation of the two Seismic Shutdown Systems with Environmental Enclosures; Fabrication and installation of in-pit pipe jumpers, including related valves, instruments and wiring; and Installation of a vertical submersible pump, horizontal booster pump, and winch assembly into tank access riser pits.

Project W-320, 241-C-106 sluicing: Construction specification W-320-C6

Energy Technology Data Exchange (ETDEWEB)

Bailey, J.W.

1998-07-20

This supporting document has been prepared to make the construction specifications for Project W-320 readily available. Project W-320, Waste Retrieval Sluicing System (WRSS), specification is for procurement, fabrication and installation of equipment at the C Tank Farm, including Operator Station and some equipment just outside the C Tank Farm fence, necessary to support the sluicing operation. Work consists of furnishing labor, equipment, and materials to provide the means to procure materials and equipment, fabricate items, excavate and place concrete, and install equipment, piping, wiring, and structures in accordance with the Contract Documents. Major work elements include: Excavation for process and fire protection piping, electrical conduit trenches, and foundations for small structures; Placement of concrete cover blocks, foundations, and equipment pads; Procurement and installation of double walled piping, electrical conduit, fire and raw water piping, chilled water piping, and electrical cable; Procurement and installation of above-ground ventilation system piping between the (HVAC) Process building and Tank C-106; Core drill existing concrete; Furnish and installation of electrical distribution equipment; Installation of the concrete foundation, and assembly installation of the two Seismic Shutdown Systems with Environmental Enclosures; Fabrication and installation of in-pit pipe jumpers, including related valves, instruments and wiring; and Installation of a vertical submersible pump, horizontal booster pump, and winch assembly into tank access riser pits.

Development of a Self-Sluicing Pressure Leaf Filter

Science.gov (United States)

Cousineau, Bernard L.; Lumsden, J. R.

The cylindrical Kelly filter presses installed in the Ewarton Works "C" phase did not perform satisfactorily because of difficulties with head seals, locking rings, and shell retraction mechanisms. As rectification required major modifications, a concept of a press which did not require to be opened for sluicing was proposed. Test work of various sluicing and res lurrying spray arrangements was carried out, and this led to the design of a self-sluicing press which used the shell of an existing Kelly press with its main axis vertical. One press was converted by July 1972, and a development period started. Although initial operation was encouraging, effective sluicing could not be guaranteed after 30 shifts. Modifications to leaf spacing, spray rotational speed, spray slot width, feed pressure and pre-coat control by November 1973, however, allowed effective performance for all of the 800 hour canvas life. Advantages are: reduced operating and maintenance manpower, clean environment, and reduced maintenance cost. The use of 1st wash overflow for sluicing has reduced caustic soda and canvas consumption. Ewarton Works now has four converted self-sluicing presses, and arc converting five more, and Arvida Works plan the installation of one for tests on red pressing (blow-off filtration). A side benefit of the development was the study of the benefits of constant pressure overflow filtration.

The gelsluice, an innovative idea for the present sluice structures

Directory of Open Access Journals (Sweden)

de Gijt Jacob Gerrit (Jarit

2017-01-01

Full Text Available Sluices have been built worldwide since in 984 when the first sluice was built in China to speed up the operations in the Grand canal. Since that time different types of sluices have been developed world wide both in size and material use and their own shipping and structural characteristics. One of the main drawbacks of the present sluice designs is the waiting time. This problem of the waiting time is in principle overcome by the design of the gelsluice (gellock. This paper describe the development of sluices construction in general and with the emphasis on the characteristics of the innovative gelsluice. A preliminary design of the gelsluice will be discussed and presented. Finally some recommendations are presented for further research to improve the design of the gelsluice.

Tanks Focus Area retrieval process development and enhancements FY96 technology development summary report

International Nuclear Information System (INIS)

Rinker, M.W.; Bamberger, J.A.; Hatchell, B.K.

1996-09-01

The Retrieval Process Development and Enhancements (RPD ampersand E) activities are part of the Retrieval and Closure Program of the U.S. Department of Energy (DOE) EM-50 Tanks Focus Area. The purposes of RPD ampersand E are to understand retrieval processes, including emerging and existing technologies, and to gather data on those processes, so that end users have the requisite technical basis to make retrieval decisions. Work has been initiated to support the need for multiple retrieval technologies across the DOE complex. Technologies addressed during FY96 focused on enhancements to sluicing, borehole mining, confined sluicing retrieval end effectors, the lightweight scarifier, and pulsed air mixing. Furthermore, a decision tool and database have been initiated to link retrieval processes with tank closure to assist end users in making retrieval decisions

EM-50 Tanks Focus Area retrieval process development and enhancements. FY97 technology development summary report

International Nuclear Information System (INIS)

Rinker, M.W.; Bamberger, J.A.; Alberts, D.G.

1997-09-01

The Retrieval Process Development and Enhancements (RPD and E) activities are part of the US Department of Energy (DOE) EM-50 Tanks Focus Area, Retrieval and Closure program. The purpose of RPD and E is to understand retrieval processes, including emerging and existing technologies, and to gather data on these processes, so that end users have requisite technical bases to make retrieval decisions. Technologies addressed during FY97 include enhancements to sluicing, the use of pulsed air to assist mixing, mixer pumps, innovative mixing techniques, confined sluicing retrieval end effectors, borehole mining, light weight scarification, and testing of Russian-developed retrieval equipment. Furthermore, the Retrieval Analysis Tool was initiated to link retrieval processes with tank waste farms and tank geometric to assist end users by providing a consolidation of data and technical information that can be easily assessed. The main technical accomplishments are summarized under the following headings: Oak Ridge site-gunite and associated tanks treatability study; pulsed air mixing; Oak Ridge site-Old Hydrofracture Facility; hydraulic testbed relocation; cooling coil cleaning end effector; light weight scarifier; innovative tank mixing; advanced design mixer pump; enhanced sluicing; Russian retrieval equipment testing; retrieval data analysis and correlation; simulant development; and retrieval analysis tool (RAT)

Nonradioactive air emissions notice of construction, Project W-320, 241-C-106 tank sluicing

International Nuclear Information System (INIS)

Hays, C.B.

1998-01-01

This document serves as a Notice of Construction for the Phase 2 activities of Project W-320, 241-C-106 Tank Sluicing, pursuant to the requirements of Washington Administrative Codes (WAC) 173-400 and 173-460. Phased permitting for Project W-320 was discussed with the Washington State Department of Ecology (Ecology) on November 2, 1993. In April 1994, it was deemed unnecessary because the Phase 1 activities did not constitute a new source of emissions and therefore did not require approval from Ecology. The 241-C-106 tank is a 2-million liter capacity, single-shell tank (SST) used for radioactive waste storage since 1947. Between mid-1963 and mid-1969, 241-C-106 tank received high-heat waste, PUREX (plutonium-uranium extraction) Facility high-level waste, and strontium-bearing solids from the strontium and cesium recovery activities. In 1971, temperatures exceeding 99 C were observed in the tank, and therefore, a ventilation system was installed to cool the tank. In addition, approximately 22,712 liters of cooling water are added to the tank each month to prevent the sludge from drying out and overheating. Excessive drying of the sludge could result in possible structural damage. The current radiolytic heat generation rate has been calculated at 32 kilowatts (kW) plus or minus 6 kW. The 241-C-106 tank was withdrawn from service in 1979 and currently is categorized as not leaking. The heat generation in 241-C-106 tank has been identified as a key safety issue on the Hanford Site. The evaporative cooling provided by the added water during operation and/or sluicing maintains the 241-C-106 tank within its specified operating temperature limits. Project W-320, 241-C-106 Tank Sluicing, will mobilize and remove the heat-generating sludge, allowing the water additions to cease. Following sludge removal, the 241-C-106 tank could be placed in a safe, interim stabilized condition. Tank-to-tank sluicing, an existing, proven technology, will provide the earliest possible

Nonradioactive air emissions notice of construction, Project W-320, 241-C-106 tank sluicing

Energy Technology Data Exchange (ETDEWEB)

Hays, C.B.

1998-01-28

This document serves as a Notice of Construction for the Phase 2 activities of Project W-320, 241-C-106 Tank Sluicing, pursuant to the requirements of Washington Administrative Codes (WAC) 173-400 and 173-460. Phased permitting for Project W-320 was discussed with the Washington State Department of Ecology (Ecology) on November 2, 1993. In April 1994, it was deemed unnecessary because the Phase 1 activities did not constitute a new source of emissions and therefore did not require approval from Ecology. The 241-C-106 tank is a 2-million liter capacity, single-shell tank (SST) used for radioactive waste storage since 1947. Between mid-1963 and mid-1969, 241-C-106 tank received high-heat waste, PUREX (plutonium-uranium extraction) Facility high-level waste, and strontium-bearing solids from the strontium and cesium recovery activities. In 1971, temperatures exceeding 99 C were observed in the tank, and therefore, a ventilation system was installed to cool the tank. In addition, approximately 22,712 liters of cooling water are added to the tank each month to prevent the sludge from drying out and overheating. Excessive drying of the sludge could result in possible structural damage. The current radiolytic heat generation rate has been calculated at 32 kilowatts (kW) plus or minus 6 kW. The 241-C-106 tank was withdrawn from service in 1979 and currently is categorized as not leaking. The heat generation in 241-C-106 tank has been identified as a key safety issue on the Hanford Site. The evaporative cooling provided by the added water during operation and/or sluicing maintains the 241-C-106 tank within its specified operating temperature limits. Project W-320, 241-C-106 Tank Sluicing, will mobilize and remove the heat-generating sludge, allowing the water additions to cease. Following sludge removal, the 241-C-106 tank could be placed in a safe, interim stabilized condition. Tank-to-tank sluicing, an existing, proven technology, will provide the earliest possible

Interim safety equipment list for 241-C-106 waste retrieval, project W-320

International Nuclear Information System (INIS)

Conner, J.C.

1996-01-01

The purpose of this supporting document is to provide safety classifications for systems, structures, and components of the Tank 241-C-106 Waste Retrieval Sluicing System (WRSS) and to document the methodology used to develop these safety classifications. The WRSS requires two transfer lines, one to carry sluiced waste slurry to tank 241-AY-102 and the other to return supernatant to tank 241-C-106; pumps in each tank; sluicers to direct the supernatant stream inside tank 241-C-106; a slurry distributor in tank 241-AY-102; heating, ventilation, and air conditioning for tank 241-C-106; and instrumentation and control devices

Interim safety equipment list for 241-C-106 waste retrieval, project W-320

Energy Technology Data Exchange (ETDEWEB)

Conner, J.C.

1996-01-25

The purpose of this supporting document is to provide safety classifications for systems, structures, and components of the Tank 241-C-106 Waste Retrieval Sluicing System (WRSS) and to document the methodology used to develop these safety classifications. The WRSS requires two transfer lines, one to carry sluiced waste slurry to tank 241-AY-102 and the other to return supernatant to tank 241-C-106; pumps in each tank; sluicers to direct the supernatant stream inside tank 241-C-106; a slurry distributor in tank 241-AY-102; heating, ventilation, and air conditioning for tank 241-C-106; and instrumentation and control devices.

Structure modulates similarity-based interference in sluicing: An eye tracking study.

Directory of Open Access Journals (Sweden)

Jesse A. Harris

2015-12-01

Full Text Available In cue-based content-addressable approaches to memory, a target and its competitors are retrieved in parallel from memory via a fast, associative cue-matching procedure under a severely limited focus of attention. Such a parallel matching procedure could in principle ignore the serial order or hierarchical structure characteristic of linguistic relations. I present an eye tracking while reading experiment that investigates whether the sentential position of a potential antecedent modulates the strength of similarity-based interference, a well-studied effect in which increased similarity in features between a target and its competitors results in slower and less accurate retrieval overall. The manipulation trades on an independently established Locality bias in sluiced structures to associate a wh-remnant (which ones in clausal ellipsis with the most local correlate (some wines, as in The tourists enjoyed some wines, but I don’t know which ones. The findings generally support cue-based parsing models of sentence processing that are subject to similarity-based interference in retrieval, and provide additional support to the growing body of evidence that retrieval is sensitive to both the structural position of a target antecedent and its competitors, and the specificity of retrieval cues.

First generation long-reach manipulator for retrieval of waste from Hanford single-shell tanks

International Nuclear Information System (INIS)

Gibbons, P.W.; McDaniel, L.B.

1994-10-01

The US Department of Energy, Richland Operations Office, has established the Tank Waste Remediation System to resolve environmental and safety issues related to underground waste-storage tanks at the Hanford Site. The Tank Waste Remediation System has identified the use of an advanced-technology, long-reach manipulator system as a low-water-addition retrieval alternative to past-practice sluicing

Decision analysis for the selection of tank waste retrieval technology

International Nuclear Information System (INIS)

DAVIS, FREDDIE J.; DEWEESE, GREGORY C.; PICKETT, WILLIAM W.

2000-01-01

The objective of this report is to supplement the C-104 Alternatives Generation and Analysis (AGA) by providing a decision analysis for the alternative technologies described therein. The decision analysis used the Multi-Attribute Utility Analysis (MUA) technique. To the extent possible information will come from the AGA. Where data are not available, elicitation of expert opinion or engineering judgment is used and reviewed by the authors of the AGA. A key element of this particular analysis is the consideration of varying perspectives of parties interested in or affected by the decision. The six alternatives discussed are: sluicing; sluicing with vehicle mounted transfer pump; borehole mining; vehicle with attached sluicing nozzle and pump; articulated arm with attached sluicing nozzle; and mechanical dry retrieval. These are evaluated using four attributes, namely: schedule, cost, environmental impact, and safety

Development of a waste dislodging and retrieval system for use in the Oak Ridge National Laboratory gunite tank

International Nuclear Information System (INIS)

Randolph, J.D.; Lloyd, P.D.; Burks, B.L.

1997-01-01

As part of the Gunite And Associated Tanks (GAAT) Treatability Study the Oak Ridge National Laboratory (ORNL) has developed a tank waste retrieval system capable of removing wastes varying from liquids to thick sludges. This system is also capable of scarifying concrete walls and floors. The GAAT Treatability Study is being conducted by the Department of Energy Oak Ridge Environmental Restoration Program. Much of the technology developed for this project was cosponsored by the DOE Office of Science and Technology through the Tanks Focus Area (TFA) and the Robotics Technology Development Program. The waste dislodging and conveyance (WD ampersand C) system was developed jointly by ORNL and participants from the TFA. The WD ampersand C system is comprised of a four degree-of-freedom arm with back driveable motorized joints. a cutting and dislodging tool, a jet pump and hose management system for conveyance of wastes, confined sluicing end-effector, and a control system, and must be used in conjunction with a robotic arm or vehicle. Other papers have been submitted to this conference describing the development and operation of the arm and vehicle positioning systems. This paper will describe the development of the WD ampersand C system and its application for dislodging and conveyance of ORNL sludges from the GAAT tanks. The confined sluicing end-effector relies on medium pressure water jets to dislodge waste that is then pumped by the jet pump through the conveyance system out of the tank. This paper will describe the results of cold testing of the integrated system. At the conference presentation there will also be results from the field deployment. ORNL has completed fabrication of the WD ampersand C system for waste removal and is full-scale testing, including testing of the confined sluicing end-effector

Alternate retrieval technology demonstrations program - test report (ARD Environmental, Inc.)

International Nuclear Information System (INIS)

Berglin, E.J.

1997-01-01

A prototype vehicle, control system, and waste and water scavenging system were designed and fabricated with essentially the full capabilities of the vehicle system proposed by ARD Environmental. A test tank mockup, including riser and decontamination chamber were designed and fabricated, and approximately 830 cubic feet of six varieties of waste simulants poured. The tests were performed by ARD Environmental personnel at its site in Laurel, Maryland, from 4/22/97 through 5/2/97. The capabilities tested were deployment and retrieval, extended mobility and productivity, the ability to operate the system using video viewing only, retrieval after simulated failure, and retrieval and decontamination. Testing commenced with deployment of the vehicle into the tank. Deployment was accomplished using a crane and auxiliary winch to position the vehicle and lower it through the decontamination chamber, into the 36'' diameter x 6' high riser, and touch down on the waste field in the tank. The initial mobility tests were conducted immediately after deployment, prior to sluicing, as the waste field exhibited the greatest amount of variation at this time. This test demonstrated the ability of the vehicle to maneuver over the simulated waste field, and the ability of the operator to work with only video viewing available. In addition, the ability of the vehicle to right itself after being turned on its side was demonstrated. The production rate was evaluated daily through the testing period by measuring the surface and estimating the amount of material removed. The test demonstrated the ability of the vehicle to reduce the waste surface using 400 psi (nominal) water jets, scavenge water and material from the work area, and move to any location, even in the relatively confined space of the 20' diameter test tank. In addition, the ability to sluice to a remote scavenging module was demonstrated. The failure mode test demonstrated the ability to retrieve a stuck vehicle by pulling

Alternate retrieval technology demonstrations program - test report (ARD Environmental, Inc.)

Energy Technology Data Exchange (ETDEWEB)

Berglin, E.J.

1997-07-31

A prototype vehicle, control system, and waste and water scavenging system were designed and fabricated with essentially the full capabilities of the vehicle system proposed by ARD Environmental. A test tank mockup, including riser and decontamination chamber were designed and fabricated, and approximately 830 cubic feet of six varieties of waste simulants poured. The tests were performed by ARD Environmental personnel at its site in Laurel, Maryland, from 4/22/97 through 5/2/97. The capabilities tested were deployment and retrieval, extended mobility and productivity, the ability to operate the system using video viewing only, retrieval after simulated failure, and retrieval and decontamination. Testing commenced with deployment of the vehicle into the tank. Deployment was accomplished using a crane and auxiliary winch to position the vehicle and lower it through the decontamination chamber, into the 36`` diameter x 6` high riser, and touch down on the waste field in the tank. The initial mobility tests were conducted immediately after deployment, prior to sluicing, as the waste field exhibited the greatest amount of variation at this time. This test demonstrated the ability of the vehicle to maneuver over the simulated waste field, and the ability of the operator to work with only video viewing available. In addition, the ability of the vehicle to right itself after being turned on its side was demonstrated. The production rate was evaluated daily through the testing period by measuring the surface and estimating the amount of material removed. The test demonstrated the ability of the vehicle to reduce the waste surface using 400 psi (nominal) water jets, scavenge water and material from the work area, and move to any location, even in the relatively confined space of the 20` diameter test tank. In addition, the ability to sluice to a remote scavenging module was demonstrated. The failure mode test demonstrated the ability to retrieve a stuck vehicle by pulling

Contingency plan for the Old Hydrofracture Facility Tanks Sluicing Project at Oak Ridge National Laboratory, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

1998-06-01

This revised contingency plan addresses potential scenarios involving the release of radioactively contaminated waste from the Old Hydrofracture Facility Tanks Contents Removal project to the environment. The tanks are located at the Oak Ridge National Laboratory. The project involves sluicing the contents of the five underground tanks to mix the sludge and supernatant layers, and pumping the mixture to the Melton Valley Storage Tanks (MVST) for future processing. The sluicing system to be used for the project consists of a spray nozzle designated the open-quotes Borehole Miner,close quotes with an associated pump; in-tank submersible pumps to transfer tank contents from the sluice tanks to the recycle tank; high-pressure pumps providing slurry circulation and slurry transport to the MVST; piping; a ventilation system; a process water system; an instrumentation and control system centered around a programmable logic controller; a video monitoring system; and auxiliary equipment. The earlier version of this plan, which was developed during the preliminary design phase of the project, identified eight scenarios in which waste from the tanks might be released to the environment as a result of unanticipated equipment failure or an accident (e.g., vehicular accident). One of those scenarios, nuclear criticality, is no longer addressed by this plan because the tank waste will be isotopically diluted before sluicing begins. The other seven scenarios have been combined into three, and a fourth, Borehole Miner Failure, has been added as follows: (1) underground release from the tanks; (2) aboveground release or spill from the sluicing system, a tank riser, or the transfer pipeline; (3) release of unfiltered air through the ventilation system; and (4) Borehole Miner arm retraction failure. Methods for preventing, detecting, and responding to each release scenario are set out in the plan

DEVELOPMENT AND DEPLOYMENT OF THE MOBILE ARM RETRIEVAL SYSTEM (MARS) - 12187

Energy Technology Data Exchange (ETDEWEB)

BURKE CA; LANDON MR; HANSON CE

2011-11-08

Washington River Protection Solutions (WRPS) is developing and deploying Mobile Arm Retrieval System (MARS) technologies solutions to support retrieval of radioactive and chemical waste from underground single shell storage tanks (SST) located at the Hanford Site, which is near Richland, Washington. WRPS has developed the MARS using a standardized platform that is capable of deploying multiple retrieval technologies. To date, WRPS, working with their mentor-protege company, Columbia Energy and Environmental Services (CEES), has developed two retrieval mechanisms, MARS-Sluicing (MARS-S) and MARS-Vacuum (MARS-V). MARS-S uses pressurized fluids routed through spray nozzles to mobilize waste materials to a centrally located slurry pump (deployed in 2011). MARS-V uses pressurized fluids routed through an eductor nozzle. The eductor nozzle allows a vacuum to be drawn on the waste materials. The vacuum allows the waste materials to be moved to an in-tank vessel, then extracted from the SST and subsequently pumped to newer and safer double shell tanks (DST) for storage until the waste is treated for disposal. The MARS-S system is targeted for sound SSTs (i.e., non leaking tanks). The MARS-V is targeted for assumed leaking tanks or those tanks that are of questionable integrity. Both versions of MARS are beinglhave been developed in compliance with WRPS's TFC-PLN-90, Technology Development Management Plan [1]. TFC-PLN-90 includes a phased approach to design, testing, and ultimate deployment of new technologies. The MARS-V is scheduled to be deployed in tank 241-C-105 in late 2012.

DEVELOPMENT AND DEPLOYMENT OF THE MOBILE ARM RETRIEVAL SYSTEM (MARS) - 12187

Energy Technology Data Exchange (ETDEWEB)

BURKE CA; LANDON MR; HANSON CE

2012-01-30

Washington River Protection Solutions (WRPS) is developing and deploying Mobile Arm Retrieval System (MARS) technologies solutions to support retrieval of radioactive and chemical waste from underground single shell storage tanks (SST) located at the Hanford Site, which is near Richland, Washington. WRPS has developed the MARS using a standardized platform that is capable of deploying multiple retrieval technologies. To date, WRPS, working with their mentor-protege company, Columbia Energy and Environmental Services (CEES), has developed two retrieval mechanisms, MARS-Sluicing (MARS-S) and MARS-Vacuum (MARS-V). MARS-S uses pressurized fluids routed through spray nozzles to mobilize waste materials to a centrally located slurry pump (deployed in 2011). MARS-V uses pressurized fluids routed through an eductor nozzle. The eductor nozzle allows a vacuum to be drawn on the waste materials. The vacuum allows the waste materials to be moved to an in-tank vessel, then extracted from the SST and subsequently pumped to newer and safer double shell tanks (DST) for storage until the waste is treated for disposal. The MARS-S system is targeted for sound SSTs (i.e., non leaking tanks). The MARS-V is targeted for assumed leaking tanks or those tanks that are of questionable integrity. Both versions of MARS are being/have been developed in compliance with WRPS's TFC-PLN-90, Technology Development Management Plan. TFC-PLN-90 includes a phased approach to design, testing, and ultimate deployment of new technologies. The MARS-V is scheduled to be deployed in tank 241-C-105 in late 2012.

PERBANDINGAN EFEKTIFITAS HASIL PENGGELONTORAN SEDIMEN DI WADUK CARA FLUSHING DAN SLUICING

Directory of Open Access Journals (Sweden)

Pranoto S. Atmodjo

2013-10-01

Full Text Available This study compares the effectiveness of the flushing of sediment in the reservoir by means of flushing andSluicing way, based on Physical Hydraulic Test (Model Test in the laboratory. Flushing is removingaccumulated deposited sediment. While slucing is releasing of sediment through the reservoir beforesettled or keep sediment remain in suspension and its occur during flood period. Sediments FlushEffectiveness represented by the percentage of released sediment by sediment deposited or the amount ofsediment entering the reservoir during the flushing period.The model based on the prototipe from DetailDesign of Structural Countermeasures for Sedimentation on Wonogiri Reservoir by Nippon Koei 2009.Running model duration is one hour, used free flow and submergence condition, with discharge variationQ=100, 200 and 400 m3/s. Sluicing experiments conducted with some 60 liters of sediment sprinkle evenlywide flow, and Flushing implemented by 2,00 m thickness of deposited sediment that spreaded over thereservoir bottom before running. From this research showed that Sluicing way more efficient than theflushing way, where the number of efficiency of sediment Sluicing way bigger than the efficiency offlusing way, in the running an hour in the laboratory test

Experimental investigation on the relationship between sluice caisson shape of tidal power plant and the water discharge capability

Energy Technology Data Exchange (ETDEWEB)

Lee, Dal Soo; Oh, Sang-Ho; Yi, Jin-Hak; Park, Woo-Sun [Coastal Engineering and Ocean Energy Research Department, Korea Ocean Research and Development Institute, Ansan 426-744 (Korea); Cho, Hyu-Sang; Kim, Duk-Gu; Ahn, Suk-Jin [Technology Research and Development Institute, Hyein E and C Co. Ltd., Seoul 157-861 (Korea); Eom, Hyun-Min [Global Environment System Research Laboratory, National Institute of Meteorological Research/KMA, Seoul 156-720 (Korea)

2010-10-15

The change of water discharge capability of the sluice caisson of tidal power plant according to the change of geometrical shape of the sluice caisson was investigated by performing laboratory experiments. The major design parameters that constitute general shape of the sluice caisson were deduced and a total of 32 different shapes of sluice caisson models were subjected to the hydraulic experiments. For every sluice caisson model, the water discharge capability was estimated with five different flow rates and three different water level conditions. The experiments were carried out in an open channel flume with a great care to measure flow rate and water level accurately, which are key physical quantities in estimating the water discharge capability of the sluice caisson models. By analyzing the experimental results, influence of the respective design parameters on the performance of the sluice caisson was examined and the general guidelines to enhance the water discharge capability were suggested. The discharge coefficient of the best sluice caisson model ranged from 2.3 to 3.1 depending on the experimental conditions, which is far higher than the values that were adopted in the past feasibility studies in Korea. (author)

Complex composition film condensation in the sluice device of an electron microscope

International Nuclear Information System (INIS)

Kukuev, V.I.; Lesovoj, M.V.; Vlasov, D.A.; Malygin, M.V.; Domashevskaya, Eh.P.; Tomashpol'skij, Yu.Ya.

1994-01-01

Based on the sluice device of an electron microscope a system is developed for material laser evaporation and vapor condensation on a substrate, situated in the microscope specimen holder. Substrate heating by laser radiation to 100 deg C is used. The system is applied for investigating growth of high-temperature superconductor films

Initial ACTR retrieval technology evaluation test material recommendations

International Nuclear Information System (INIS)

Powell, M.R.

1996-04-01

Millions of gallons of radiaoctive waste are contained in underground storage tanks at Hanford (SE Washington). Techniques for retrieving much of this waste from the storage tanks have been developed. Current baseline approach is to use sluice jets for single-shell tanks and mixer pumps for double-shell tanks. The Acquire Commercial Technology for Retrieval (ACTR) effort was initiated to identify potential improvements in or alternatives to the baseline waste retrieval methods. Communications with a variety of vendors are underway to identify improved methods that can be implemented at Hanford with little or no additional development. Commercially available retrieval methods will be evaluated by a combination of testing and system-level cost estimation. Current progress toward developing waste simulants for testing ACTR candidate methods is reported; the simulants are designed to model 4 different types of tank waste. Simulant recipes are given for wet sludge, hardpan/dried sludge,hard saltcake, and soft saltcake. Comparisons of the waste and simulant properties are documented in this report

Identification of physical properties for the retrieval data quality objective process

International Nuclear Information System (INIS)

Gates, C.M.; Beckette, M.R.

1995-06-01

This activity supports the retrieval data quality objective (DQO) process by identifying the material properties that are important to the design, development, and operation of retrieval equipment; the activity also provides justification for characterizing those properties. These properties, which control tank waste behavior during retrieval operations, are also critical to the development of valid physical simulants for designing retrieval equipment. The waste is to be retrieved in a series of four steps. First, a selected retrieval technology breaks up or dislodges the waste into subsequently smaller pieces. Then, the dislodged waste is conveyed out of the tank through the conveyance line. Next, the waste flows into a separator unit that separates the gaseous phase from the liquid and solid phases. Finally, a unit may be present to condition the slurried waste before transporting it to the treatment facility. This document describes the characterization needs for the proposed processes to accomplish waste retrieval. Baseline mobilization technologies include mixer pump technology, sluicing, and high-pressure water-jet cutting. Other processes that are discussed in this document include slurry formation, pneumatic conveyance, and slurry transport. Section 2.0 gives a background of the DQO process and the different retrieval technologies. Section 3.0 provides the mechanistic descriptions and material properties critical to the different technologies and processes. Supplemental information on specific technologies and processes is provided in the appendices. Appendix A contains a preliminary sluicing model, and Appendices B and C cover pneumatic transport and slurry transport, respectively, as prepared for this document. Appendix D contains sample calculations for various equations

Study on ecological regulation of coastal plain sluice

Science.gov (United States)

Yu, Wengong; Geng, Bing; Yu, Huanfei; Yu, Hongbo

2018-02-01

Coastal plains are densely populated and economically developed, therefore their importance is self-evident. However, there are some problems related with water in coastal plains, such as low flood control capacity and severe water pollution. Due to complicated river network hydrodynamic force, changeable flow direction and uncertain flood concentration and propagation mechanism, it is rather difficult to use sluice scheduling to realize flood control and tackle water pollution. On the base of the measured hydrological data during once-in-a-century Fitow typhoon in 2013 in Yuyao city, by typical analysis, theoretical analysis and process simulation, some key technologies were researched systematically including plain river network sluice ecological scheduling, “one tide” flood control and drainage scheduling and ecological running water scheduling. In the end, single factor health diagnostic evaluation, unit hydrograph of plain water level and evening tide scheduling were put forward.

Project W-320 Tank 106-C waste retrieval study analysis session report

International Nuclear Information System (INIS)

Bailey, J.W.

1998-01-01

This supporting document has been prepared to make the Kaiser Engineers Hanford Company Project W-320 Tank 106-C Waste Retrieval Study Analysis Session Report readily retrievable. This facilitated session was requested by Westinghouse Hanford Company (WHC) to review the characterization data and select the best alternatives for a double-shell receiver tank and for a sluicing medium for Tank 106-C waste retrieval. The team was composed of WHC and Kaiser Engineers Hanford Company (KEH) personnel knowledgeable about tank farm operations, tank 106-C requirements, tank waste characterization and analysis, and chemical processing. This team was assembled to perform a structured decision analysis evaluation and recommend the best alternative-destination double-shell tank between tanks 101-AY and 102-AY, and the best alternative sluicing medium among dilute complexant (DC), dilute noncomplexant (DNC), and water. The session was facilitated by Richard Harrington and Steve Bork of KEH and was conducted at the Bookwalter Winery in Richland from 7:30 a.m. to 4:00 p.m. from July 27 through July 29, 1993. Attachment 1 (Scope Statement Sheet) identifies the team members, scope, objectives, and deliverables for the session

Tank 241-C-106 in-tank imaging system operational test report

International Nuclear Information System (INIS)

Pedersen, L.T.

1998-01-01

This document presents the results of operational testing of the 241-C-106 In-Tank Video Camera Imaging System. This imaging system was installed as a component of Project W-320 to monitor sluicing and waste retrieval activities in Tank 241-C-106

The Real-Time Processing of Sluiced Sentences

Science.gov (United States)

Poirier, Josee; Wolfinger, Katie; Spellman, Lisa; Shapiro, Lewis P.

2010-01-01

Ellipsis refers to an element that is absent from the input but whose meaning can nonetheless be recovered from context. In this cross-modal priming study, we examined the online processing of Sluicing, an ellipsis whose antecedent is an entire clause: "The handyman threw a book to the programmer but I don't know which book" the handyman threw to…

Identification of key factors affecting the water pollutant concentration in the sluice-controlled river reaches of the Shaying River in China via statistical analysis methods.

Science.gov (United States)

Dou, Ming; Zhang, Yan; Zuo, Qiting; Mi, Qingbin

2015-08-01

The construction of sluices creates a strong disturbance in water environmental factors within a river. The change in water pollutant concentrations of sluice-controlled river reaches (SCRRs) is more complex than that of natural river segments. To determine the key factors affecting water pollutant concentration changes in SCRRs, river reaches near the Huaidian Sluice in the Shaying River of China were selected as a case study, and water quality monitoring experiments based on different regulating modes were implemented in 2009 and 2010. To identify the key factors affecting the change rates for the chemical oxygen demand of permanganate (CODMn) and ammonia nitrogen (NH3-N) concentrations in the SCRRs of the Huaidian Sluice, partial correlation analysis, principal component analysis and principal factor analysis were used. The results indicate four factors, i.e., the inflow quantity from upper reaches, opening size of sluice gates, water pollutant concentration from upper reaches, and turbidity before the sluice, which are the common key factors for the CODMn and NH3-N concentration change rates. Moreover, the dissolved oxygen before a sluice is a key factor for the permanganate concentration from CODMn change rate, and the water depth before a sluice is a key factor for the NH3-N concentration change rate. Multiple linear regressions between the water pollutant concentration change rate and key factors were established via multiple linear regression analyses, and the quantitative relationship between the CODMn and NH3-N concentration change rates and key affecting factors was analyzed. Finally, the mechanism of action for the key factors affecting the water pollutant concentration changes was analyzed. The results reveal that the inflow quantity from upper reaches, opening size of sluice gates, permanganate concentration from CODMn from upper reaches and dissolved oxygen before the sluice have a negative influence and the turbidity before the sluice has a positive

Engineering study of tank leaks related to hydraulic retrieval of sludge from tank 241-C-106

International Nuclear Information System (INIS)

Lowe, S.S.; Carlos, W.C.; Irwin, J.J.; Khaleel, R.; Kline, N.W.; Ludowise, J.D.; Marusich, R.M.; Rittman, P.D.

1993-01-01

This study evaluates hydraulic retrieval (sluicing) of the waste in single-shell tank 241-C-106 with respect to the likelihood of tank leaks, gross volumes of potential leaks, and their consequences. A description of hydraulic retrieval is developed to establish a baseline for the study. Leak models are developed based on postulated leak mechanisms to estimate the amount of waste that could potentially leak while sluicing. Transport models describe the movement of the waste constituents in the surrounding soil and groundwater after a leak occurs. Environmental impact and risk associated with tank leaks are evaluated. Transport of leaked material to the groundwater is found to be dependent on the rate of recharge of moisture in the soil for moderate-sized leaks. Providing a cover over the tank and surrounding area would eliminate the recharge. The bulk of any leaked material would remain in the vicinity of the tank for remedial action

TANK FARM RETRIEVAL LESSONS LEARNED AT THE HANFORD SITE

International Nuclear Information System (INIS)

DODD RA

2008-01-01

One of the environmental remediation challenges facing the nation is the retrieval and permanent disposal of approximately 90 million gallons of radioactive waste stored in underground tanks at the U. S. Department of Energy (DOE) facilities. The Hanford Site is located in southeastern Washington State and stores roughly 60 percent of this waste. An estimated 53 million gallons of high-level, transuranic, and low-level radioactive waste is stored underground in 149 single-shell tanks (SSTs) and 28 newer double-shell tanks (DSTs) at the Hanford Site. These SSTs range in size from 55,000 gallons to 1,000,000 gallon capacity. Approximately 30 million gallons of this waste is stored in SSTs. The SSTs were constructed between 1943 and 1964 and all have exceeded the nominal 20-year design life. Sixty-seven SSTs are known or suspected to have leaked an estimated 1,000,000 gallons of waste to the surrounding soil. The risk of additional SST leakage has been greatly reduced by removing more than 3 million gallons of interstitial liquids and supernatant and transferring this waste to the DST system. Retrieval of SST saltcake and sludge waste is underway to further reduce risks and stage feed materials for the Hanford Site Waste Treatment Plant. Regulatory requirements for SST waste retrieval and tank farm closure are established in the Hanford Federal Facility Agreement and Consent Order (HFFACO), better known as the TriParty Agreement, or TPA. The HFFACO was signed by the DOE, the State of Washington Department of Ecology (Ecology), and U. S. Environmental Protection Agency (EPA) and requires retrieval of as much waste as technically possible, with waste residues not to exceed 360 fe in 530,000 gallon or larger tanks; 30 fe in 55,000 gallon or smaller tanks; or the limit of waste retrieval technology, whichever is less. If residual waste volume requirements cannot be achieved, then HFFACO Appendix H provisions can be invoked to request Ecology and EPA approval of an

Hydraulic performance of sluice gate with unloaded upstream rotor ...

African Journals Online (AJOL)

... compared to the flow under rotor and weir flow conditions. The video analysis also indicated that significant perturbation exists for the rotor angular speed. The normalized perturbation intensity varied from a minimum of 8% to a maximum of 60%. Keywords: sluice gate, rotor, angular speed, video analysis, hydropower ...

Potential for criticality in Hanford tanks resulting from retrieval of tank waste

International Nuclear Information System (INIS)

Whyatt, G.A.; Sterne, R.J.; Mattigod, S.V.

1996-09-01

This report assesses the potential during retrieval operations for segregation and concentration of fissile material to result in a criticality. The sluicing retrieval of C-106 sludge to AY-102 and the operation of mixer pumps in SY-102 are examined in some detail. These two tanks (C-106, SY-102) were selected because of the near term plans for retrieval of these tanks and their high plutonium inventories relative to other tanks. Although all underground storage tanks are subcritical by a wide margin if assumed to be uniform in composition, the possibility retrieval operations could preferentially segregate the plutonium and locally concentrate it sufficiently to result in criticality was a concern. This report examines the potential for this segregation to occur

Quantitative relations between chemical oxygen demand concentration and its influence factors in the sluice-controlled river reaches of Shaying River, China.

Science.gov (United States)

Dou, Ming; Li, Guiqiu; Li, Congying

2015-01-01

Recent research on the effects of dam and sluice construction on the water environment has attracted extensive attention from academia and governments alike. Because the operation of sluices greatly alters environmental factors such as water flow and sediment load, the water quality in sluice-controlled river reaches (SCRRs) undergoes complex changes compared with those in normal reaches. This work used river reaches near the Huaidian Sluice in Shaying River of China as a case study to analyse the effects of sluice operation on water quality evolution in SCRRs. The most influential factors affecting the rate of change in chemical oxygen demand (COD) concentration in SCRRs were identified through water quality monitoring experiments performed under various modes of sluice operation and by applying a statistical method 'partial correlation analysis'. Then, a hydrodynamic model incorporating sluice operation and a water quality transport and transform model incorporating the release of endogenous loads were developed. Using these two models, the processes of temporal and spatial change of COD concentrations in the SCRRs were simulated under various scenarios designed to represent the dominant factors of influence. Finally, the simulation results were used to develop empirical relationships between the rate of change in COD concentrations and the dominant factors of influence. The results reveal that three factors, i.e., water inflow concentration, gate opening size, and gate opening number, are the dominant factors of influence, and there are logarithmic relationships between the rate of change in COD concentration in the SCRRs and these factors.

Calibration of submerged multi-sluice gates

Directory of Open Access Journals (Sweden)

Mohamed F. Sauida

2014-09-01

The main objective of this work is to study experimentally and verify empirically the different parameters affecting the discharge through submerged multiple sluice gates (i.e., the expansion ratios, gates operational management, etc.. Using multiple regression analysis of the experimental results, a general equation for discharge coefficient is developed. The results show, that the increase in the expansion ratio and the asymmetric operation of gates, give higher values for the discharge coefficient. The obtained predictions of the discharge coefficient using the developed equations are compared to the experimental data. The present developed equations showed good consistency and high accuracy.

Chemical and chemically-related considerations associated with sluicing tank C-106 waste to tank AY-102

International Nuclear Information System (INIS)

Reynolds, D.A.

1997-01-01

New data on tank 241-C-106 were obtained from grab sampling and from compatibility testing of tank C-106 and tank AY-102 wastes. All chemistry-associated and other compatibility Information compiled in this report strongly suggests that the sluicing of the contents of tank C-106, in accord with appropriate controls, will pose no unacceptable risk to workers, public safety, or the environment. In addition, it is expected that the sluicing operation will successfully resolve the High-Heat Safety Issue for tank C-106

Development and Deployment of the Extended Reach Sluicing System (ERSS) for Retrieval of Hanford Single Shell Tank Waste. Draft

International Nuclear Information System (INIS)

Bauer, Roger E.; Figley, Reed R.; Innes, A. G.

2013-01-01

A history of the evolution and the design development of Extended Reach Sluicer System (ERSS) is presented. Several challenges are described that had to be overcome to create a machine that went beyond the capabilities of prior generation sluicers to mobilize waste in Single Shell Tanks for pumping into Double Shell Tank receiver tanks. Off-the-shelf technology and traditional hydraulic fluid power systems were combined with the custom-engineered components to create the additional functionality of the ERSS, while still enabling it to fit within very tight entry envelope into the SST. Problems and challenges inevitably were encountered and overcome in ways that enhance the state of the art of fluid power applications in such constrained environments. Future enhancements to the ERSS design are explored for retrieval of tanks with different dimensions and internal obstacles

Environmental management through sluice gated bed-dam: a revived strategy for the control of Anopheles fluviatilis breeding in streams

Science.gov (United States)

Sahu, S.S.; Gunasekaran, K.; Jambulingam, P.

2014-01-01

Background & objectives: Integrated vector management (IVM) emphasizes sustainable eco-friendly methods and minimal use of chemicals. In this context, the present study highlights the environmental control of breeding of Anopheles fluviatilis, the primary malaria vector, through water management in a natural stream in Koraput district, Odisha, India. Methods: The District Rural Development Agency (DRDA), Koraput, constructed two bed-dams across streams, one in Barigaon and the other in Pipalapodar village. The bed-dam in the former village was fitted with two sluice gates whereas the bed dam constructed in the latter village was without the sluice gate. The sluice gates were opened once in a week on a fixed day to flush out the water from the dam. Anopheles immatures were sampled systematically in the streams using a dipper for density measurement and species composition. Results: There was a reduction of 84.9 per cent in the proportion of positive dips for Anopheles larvae/pupae and a reduction of 98.4 per cent in immature density (number/dip) of An. fluviatilis in the experimental downstream compared to the control following opening of the sluice gates. Interpretation & conclusions: Our findins showed that opening of sluice gates of the bed-dam regularly once in a week resulted in the control of vector breeding in the downstream due to the flushing effect of the water released with a high flow from the bed-dam that stagnated water in the upstream. The outcome of the study encourages upscaling this measure to other areas, wherever feasible. PMID:25297364

Integrated Methodologies for the 3D Survey and the Structural Monitoring of Industrial Archaeology: The Case of the Casalecchio di Reno Sluice, Italy

Directory of Open Access Journals (Sweden)

Gabriele Bitelli

2011-01-01

Full Text Available The paper presents an example of integrated surveying and monitoring activities for the control of an ancient structure, the Casalecchio di Reno sluice, located near Bologna, Italy. Several geomatic techniques were applied (classical topography, high-precision spirit levelling, terrestrial laser scanning, digital close-range photogrammetry, and thermal imagery. All these measurements were put together in a unique reference system and used in order to study the stability and the movements of the structure over the period of time observed. Moreover, the metrical investigations allowed the creation of a 3D model of the structure, and the comparison between two situations, before and after the serious damages suffered by the sluice during the winter season 2008-2009. Along with the detailed investigations performed on individual portions of the structure, an analysis of the whole sluice, carried out at a regional scale, was done via the use of aerial photogrammetry, using both recently acquired images and historical photogrammetric coverage. The measurements were carried out as part of a major consolidation and restoration activity, carried out by the “Consorzio della Chiusa di Casalecchio e del Canale di Reno”.

Actor coalitions and implementation in strategic delta planning: Opening the Haringvliet sluices in the Netherlands

Science.gov (United States)

Vermoolen, Myrthe; Hermans, Leon

2016-04-01

The sustained development of urbanizing deltas is influenced by natural and societal processes. These processes are characterized by their long time span, in which conflicting interests of different stakeholders have to be reconciled. Reaching consent between actors is a challenge itself, but maintaining this consent throughout different stages of strategic planning - from advocacy and agenda setting to implementation - over these long periods of time is even more difficult. The implementation stage still includes many different actors involved, some of which are different than the ones who agreed before, due to both the long run of the strategic delta planning, and to a shift of tasks and responsibilities. Thus, implementation of strategic plans often features delays, deviations of agreed plans and unintended outcomes. A key question therefore is how coalition dynamics in (pre-)planning stages influence and are influenced by the coalition dynamics during implementation. The different stages in strategic planning are often studied from either a plan formulation or an implementation perspective, but the connection between the two proves an important bottleneck for strategic planning in deltas. For instance, many building with nature solutions are still in their pilot-phase, and their upscaling can profit from lessons concerning past implementation efforts. The proposed contribution will use the case of the management of the Dutch Haringvliet sluices and the decision ('Kierbesluit') in 2000 to put these sluices ajar, to study the link between the different strategic delta planning stages and the role of the formation and change of actor coalitions herein. With the completion of the Haringvliet dam with outlet sluices in 1970, the Haringvliet estuary of the rivers Rhine and Meuse was closed off from the sea, creating a fresh water lake. This was done to make the Dutch Southwest delta safe from flooding, and had positive effects for agricultural water supply and

Consequences of a radioactive surface pool resulting from waste transfer operations between tanks 214-C-106 and 241-AY-102

International Nuclear Information System (INIS)

Van Vleet, R.J.

1997-01-01

This document contains supporting calculations for quantifying the dose consequences from a pool formed from an underground leak or a-leak from an above grade structure for the Waste Retrieval Sluicing System (Project W-320), i.e., sluicing the contents of Tank 241-C-106 (high heat, SST) into Tank 241-AY-102 (aging waste, DST)

Consequences of a radioactive surface pool resulting from waste transfer operations between tanks 214-C-106 and 241-AY-102

Energy Technology Data Exchange (ETDEWEB)

Van Vleet, R.J.

1997-08-05

This document contains supporting calculations for quantifying the dose consequences from a pool formed from an underground leak or a-leak from an above grade structure for the Waste Retrieval Sluicing System (Project W-320), i.e., sluicing the contents of Tank 241-C-106 (high heat, SST) into Tank 241-AY-102 (aging waste, DST).

Effect of Riffle Height and Spacing of a Sluice Board on Placer Gold ...

African Journals Online (AJOL)

Michael

2017-06-01

Jun 1, 2017 ... turbulence formed in the flow because the angular speeds of the whirl flow .... (6). Where the liquid gets in contact with the surface of the sluice board, the height of fluid, h = 0, and v = 0. ..... American Society for Quality (ASQ).

Test Objectives for the Saltcake Dissolution Retrieval Demonstration

International Nuclear Information System (INIS)

DEFIGH PRICE, C.

2000-01-01

This document describes the objectives the Saltcake Dissolution Retrieval Demonstration. The near term strategy for single-shell tank waste retrieval activities has shifted from focusing on maximizing the number of tanks entered for retrieval (regardless of waste volume or content) to a focus on scheduling the retrieval of wastes from those single-shell tanks with a high volume of contaminants of concern. These contaminants are defined as mobile, long-lived radionuclides that have a potential of reaching the groundwater and the Columbia River. This strategy also focuses on the performance of key retrieval technology demonstrations, including the Saltcake Dissolution Retrieval Demonstration, in a variety of waste forms and tank farm locations to establish a technical basis for future work. The work scope will also focus on the performance of risk assessment, retrieval performance evaluations (RPE) and incorporating vadose zone characterization data on a tank-by-tank basis, and on updating tank farm closure/post closure work plans. The deployment of a retrieval technology other than Past-Practice Sluicing (PPS) allows determination of limits of technical capabilities, as well as, providing a solid planning basis for future SST retrievals. This saltcake dissolution technology deployment test will determine if saltcake dissolution is a viable retrieval option for SST retrieval. CH2M Hill Hanford Group (CHG) recognizes the SST retrieval mission is key to the success of the River Protection Project (RPP) and the overall completion of the Hanford Site cleanup. The objectives outlined in this document will be incorporated into and used to develop the test and evaluation plan for saltcake dissolution retrievals. The test and evaluation plan will be developed in fiscal year 2001

Engineering development of a lightweight high-pressure scarifier for tank waste retrieval

Energy Technology Data Exchange (ETDEWEB)

Hatchell, B.K.

1997-09-01

The Retrieval Process Development and Enhancements Program (RPD&E) is sponsored by the U.S. Department of Energy Tanks Focus Area to investigate existing and emerging retrieval processes suitable for the retrieval of high-level radioactive waste inside underground storage tanks. This program, represented by industry, national laboratories, and academia, seeks to provide a technical and cost basis to support site-remediation decisions. Part of this program has involved the development of a high-pressure waterjet dislodging system and pneumatic conveyance integrated as a scarifier. Industry has used high-pressure waterjet technology for many years to mine, cut, clean, and scarify materials with a broad range of properties. The scarifier was developed as an alternate means of retrieving waste inside Hanford single-shell tanks, particularly hard, stubborn waste. Testing of the scarifier has verified its ability to retrieve a wide range of tank waste ranging from extremely hard waste that is resistant to other dislodging means to soft sludge and even supernatant fluid. Since the scarifier expends water at a low rate and recovers most of the water as it is used, the scarifier is well suited for retrieval of tanks that leak and cannot be safely sluiced or applications where significant waste dilution is not acceptable. Although the original scarifier was effective, it became evident that a lighter, more compact version that would be compatible with light weight deployment systems under development, such as the Light Duty Utility Arm, was needed. At the end of FY 95, the Light Weight Scarifier (LWS) was designed to incorporate the features of the original scarifier in a smaller, lighter end effector. During FY 96, the detailed design of the LWS was completed and two prototypes were fabricated.

Engineering development of a lightweight high-pressure scarifier for tank waste retrieval

International Nuclear Information System (INIS)

Hatchell, B.K.

1997-09-01

The Retrieval Process Development and Enhancements Program (RPD ampersand E) is sponsored by the U.S. Department of Energy Tanks Focus Area to investigate existing and emerging retrieval processes suitable for the retrieval of high-level radioactive waste inside underground storage tanks. This program, represented by industry, national laboratories, and academia, seeks to provide a technical and cost basis to support site-remediation decisions. Part of this program has involved the development of a high-pressure waterjet dislodging system and pneumatic conveyance integrated as a scarifier. Industry has used high-pressure waterjet technology for many years to mine, cut, clean, and scarify materials with a broad range of properties. The scarifier was developed as an alternate means of retrieving waste inside Hanford single-shell tanks, particularly hard, stubborn waste. Testing of the scarifier has verified its ability to retrieve a wide range of tank waste ranging from extremely hard waste that is resistant to other dislodging means to soft sludge and even supernatant fluid. Since the scarifier expends water at a low rate and recovers most of the water as it is used, the scarifier is well suited for retrieval of tanks that leak and cannot be safely sluiced or applications where significant waste dilution is not acceptable. Although the original scarifier was effective, it became evident that a lighter, more compact version that would be compatible with light weight deployment systems under development, such as the Light Duty Utility Arm, was needed. At the end of FY 95, the Light Weight Scarifier (LWS) was designed to incorporate the features of the original scarifier in a smaller, lighter end effector. During FY 96, the detailed design of the LWS was completed and two prototypes were fabricated

DORS: DDC Online Retrieval System.

Science.gov (United States)

Liu, Songqiao; Svenonius, Elaine

1991-01-01

Describes the Dewey Online Retrieval System (DORS), which was developed at the University of California, Los Angeles (UCLA), to experiment with classification-based search strategies in online catalogs. Classification structures in automated information retrieval are discussed; and specifications for a classification retrieval interface are…

Information retrieval system

Science.gov (United States)

Berg, R. F.; Holcomb, J. E.; Kelroy, E. A.; Levine, D. A.; Mee, C., III

1970-01-01

Generalized information storage and retrieval system capable of generating and maintaining a file, gathering statistics, sorting output, and generating final reports for output is reviewed. File generation and file maintenance programs written for the system are general purpose routines.

Safety evaluation for packaging transportation of equipment for tank 241-C-106 waste sluicing system

International Nuclear Information System (INIS)

Calmus, D.B.

1994-01-01

A Waste Sluicing System (WSS) is scheduled for installation in nd waste storage tank 241-C-106 (106-C). The WSS will transfer high rating sludge from single shell tank 106-C to double shell waste tank 241-AY-102 (102-AY). Prior to installation of the WSS, a heel pump and a transfer pump will be removed from tank 106-C and an agitator pump will be removed from tank 102-AY. Special flexible receivers will be used to contain the pumps during removal from the tanks. After equipment removal, the flexible receivers will be placed in separate containers (packagings). The packaging and contents (packages) will be transferred from the Tank Farms to the Central Waste Complex (CWC) for interim storage and then to T Plant for evaluation and processing for final disposition. Two sizes of packagings will be provided for transferring the equipment from the Tank Farms to the interim storage facility. The packagings will be designated as the WSSP-1 and WSSP-2 packagings throughout the remainder of this Safety Evaluation for Packaging (SEP). The WSSP-1 packagings will transport the heel and transfer pumps from 106-C and the WSSP-2 packaging will transport the agitator pump from 102-AY. The WSSP-1 and WSSP-2 packagings are similar except for the length

Topology of Document Retrieval Systems.

Science.gov (United States)

Everett, Daniel M.; Cater, Steven C.

1992-01-01

Explains the use of a topological structure to examine the closeness between documents in retrieval systems and analyzes the topological structure of a vector-space model, a fuzzy-set model, an extended Boolean model, a probabilistic model, and a TIRS (Topological Information Retrieval System) model. Proofs for the results are appended. (17…

Overview of Remote Retrieval Equipment and the Strategy for removal of Radon Bearing Waste from Silos 1 and 2 at the Fernald Site

International Nuclear Information System (INIS)

Rinker, Michael W.; Samuel, Todd J.

2001-01-01

This document provides an overview of the remote retrieval equipment and strategy for the retrieval of waste from Silos 1 and 2 at the Department of Energy's Fernald site in southwestern Ohio. The scope of this paper is limited to general descriptions of remote equipment specifically related in-silo retrieval. The retrieval strategy describes how the contractor team is planning to utilize the various remote subsystems to efficiently remove the waste from the silos from a philosophical standpoint as opposed to a procedural and operational standpoint. The retrieval strategy and approach is based upon the successful tank retrieval operations conducted at DOE's Oak Ridge and Hanford Sites. Lessons learned from these previous operations have been utilized in planning an approach for the Fernald Silo Retrieval Project. The equipment overview includes discussion of the retrieval system configurations together with descriptions of the robotic arm and retrieval end effectors, the conditioning and transfer pumping system, the sluicer and sluicing pump, as well as the debris retrieval system. A unique challenge being addressed as part of this project is the waste contents. Silos 1 and 2 contain two distinct layers of material that need to be retrieved. The first layer is a Bentonite (trade name BentogroutTM) cap that was placed in the silos to prevent radon migration into the dome space and out of the silos. The Bentonite layer varies, but in general it is approximately six inches deep in the center of the silo and thirty-six inches near the silo walls. The material may have dried out on the surface, and may still be wetted near the bottom of the bentonite layer. The K-65 ore tailings, which were slurried into the silos, are the remainder of the waste that is over 20' in depth. This paper provides an overview of the retrieval strategies, technologies, and techniques that will be used to safely and efficiently retrieve the waste from the Fernald Silos

Data bank for a data retrieval system

Energy Technology Data Exchange (ETDEWEB)

Vernikovskii, V V

1980-01-01

The data bank of the computerized data retrieval system is an organic and constituent part of the system; the level of technology and performance of the data retrieval system as a whole depend on the results of its design and operation. The data bank integrates a storage system for the entire set of data, as well as implementing an organization of a feasible storage mode for the system dictionary, computer processing procedures, user forms, system archieves and other service information. Functions of the data bank are computerized by means of a database control system. The retriveal system data bank was designed for the OKA database control system; the selection and evaluation of the feasibility of the OKA database control system, in turn, were one stage in the design of the system as a whole. The OKA database control system has been used to computerize data retrieval functions in the computerized data retrieval system, and also to maintain the system data bank in updated status.

Imaging through obscurations for sluicing operations in the waste storage tanks

International Nuclear Information System (INIS)

Peters, T.J.; McMakin, D.L.; Sheen, D.M.; Chieda, M.A.

1994-08-01

Waste remediators have identified that surveillance of waste remediation operations and periodic inspections of stored waste are required under very demanding and difficult viewing environments. In many cases, obscurants such as dust or water vapor are generated as part of the remediation activity. Methods are required for viewing or imaging beyond the normal visual spectrum. Work space images guide the movement of remediation equipment, creating a need for rapidly updated, near real-time imaging capability. In addition, there is a need for three-dimensional topographical data to determine the contours of the wastes, to plan retrieval campaigns, and to provide a three-dimensional map of a robot's work space as basis for collision avoidance. Three basic imaging techniques were evaluated: optical, acoustic and radar. The optical imaging methods that were examined used cameras which operated in the visible region and near-infrared region and infrared cameras which operated in the 3--5 micron and 8--12 micron wavelength regions. Various passive and active lighting schemes were tested, as well as the use of filters to eliminate reflection in the visible region. Image enhancement software was used to extend the range where visual techniques could be used. In addition, the operation of a laser range finder, which operated at 0.835 microns, was tested when fog/water droplets were suspended in the air. The acoustic technique involved using commercial acoustic sensors, operating at approximately 50 kHz and 215 kHz, to determine the attenuation of the acoustic beam in a high-humidity environment. The radar imaging methods involved performing millimeter wave (94 GHz) attenuation measurement sin the various simulated sluicing environments and performing preliminary experimental imaging studies using a W-Band (75--110 GHz) linearly scanned transceiver in a laboratory environment. The results of the tests are discussed

System engineering approach to GPM retrieval algorithms

Energy Technology Data Exchange (ETDEWEB)

Rose, C. R. (Chris R.); Chandrasekar, V.

2004-01-01

System engineering principles and methods are very useful in large-scale complex systems for developing the engineering requirements from end-user needs. Integrating research into system engineering is a challenging task. The proposed Global Precipitation Mission (GPM) satellite will use a dual-wavelength precipitation radar to measure and map global precipitation with unprecedented accuracy, resolution and areal coverage. The satellite vehicle, precipitation radars, retrieval algorithms, and ground validation (GV) functions are all critical subsystems of the overall GPM system and each contributes to the success of the mission. Errors in the radar measurements and models can adversely affect the retrieved output values. Ground validation (GV) systems are intended to provide timely feedback to the satellite and retrieval algorithms based on measured data. These GV sites will consist of radars and DSD measurement systems and also have intrinsic constraints. One of the retrieval algorithms being studied for use with GPM is the dual-wavelength DSD algorithm that does not use the surface reference technique (SRT). The underlying microphysics of precipitation structures and drop-size distributions (DSDs) dictate the types of models and retrieval algorithms that can be used to estimate precipitation. Many types of dual-wavelength algorithms have been studied. Meneghini (2002) analyzed the performance of single-pass dual-wavelength surface-reference-technique (SRT) based algorithms. Mardiana (2003) demonstrated that a dual-wavelength retrieval algorithm could be successfully used without the use of the SRT. It uses an iterative approach based on measured reflectivities at both wavelengths and complex microphysical models to estimate both No and Do at each range bin. More recently, Liao (2004) proposed a solution to the Do ambiguity problem in rain within the dual-wavelength algorithm and showed a possible melting layer model based on stratified spheres. With the No and Do

Engineer/constructor description of work for Tank 241-SY-102 retrieval system, project W-211, initial tank retrieval systems

International Nuclear Information System (INIS)

Rieck, C.A.

1996-02-01

This document provides a description of work for the design and construction of a waste retrieval system for Tank 241-SY-102. The description of work includes a working estimate and schedule, as well as a narrative description and sketches of the waste retrieval system. The working estimate and schedule are within the established baselines for the Tank 241-SY-102 retrieval system. The technical baseline is provided in Functional Design Criteria, WHC-SD-W211-FDC-001, Revision 2

Graph-Based Interactive Bibliographic Information Retrieval Systems

Science.gov (United States)

Zhu, Yongjun

2017-01-01

In the big data era, we have witnessed the explosion of scholarly literature. This explosion has imposed challenges to the retrieval of bibliographic information. Retrieval of intended bibliographic information has become challenging due to the overwhelming search results returned by bibliographic information retrieval systems for given input…

Understanding information retrieval systems management, types, and standards

CERN Document Server

Bates, Marcia J

2011-01-01

In order to be effective for their users, information retrieval (IR) systems should be adapted to the specific needs of particular environments. The huge and growing array of types of information retrieval systems in use today is on display in Understanding Information Retrieval Systems: Management, Types, and Standards, which addresses over 20 types of IR systems. These various system types, in turn, present both technical and management challenges, which are also addressed in this volume. In order to be interoperable in a networked environment, IR systems must be able to use various types of

Controlling The Surface Water of Shatt Al Arab River by using Sluice Gates

Directory of Open Access Journals (Sweden)

Ahmed Naseh Ahmed Hamdan

2016-03-01

Full Text Available The purpose of this study is to find hydrodynamic simulations of river water by controlging gates in Shatt Al Arab river. This river is formed by the meeting of the Tigris and Euphrates rivers near the city of Qurna in the south of Iraq, and it pours into the Arabian Gulf. Hydrodynamic simulations give a proper understanding performance and optimize utilization of the gates controlging the water level. Three different sluice gates opening cases simulate the water surface level using HEC-RAS in Shatt Al Arab river. These cases where being studied within two situations of Tide (the highest high water level and the lowest low water level within the downstream of Shatt Al Arab river. The study also deals with six cases of flow rates in upstream of Shatt Al Arab river. Hec-Ras model is produced by US Army for analyzing river system. This model could simulate steady and unsteady open channel flow.

Retrieval-travel-time model for free-fall-flow-rack automated storage and retrieval system

Science.gov (United States)

Metahri, Dhiyaeddine; Hachemi, Khalid

2018-03-01

Automated storage and retrieval systems (AS/RSs) are material handling systems that are frequently used in manufacturing and distribution centers. The modelling of the retrieval-travel time of an AS/RS (expected product delivery time) is practically important, because it allows us to evaluate and improve the system throughput. The free-fall-flow-rack AS/RS has emerged as a new technology for drug distribution. This system is a new variation of flow-rack AS/RS that uses an operator or a single machine for storage operations, and uses a combination between the free-fall movement and a transport conveyor for retrieval operations. The main contribution of this paper is to develop an analytical model of the expected retrieval-travel time for the free-fall flow-rack under a dedicated storage assignment policy. The proposed model, which is based on a continuous approach, is compared for accuracy, via simulation, with discrete model. The obtained results show that the maximum deviation between the continuous model and the simulation is less than 5%, which shows the accuracy of our model to estimate the retrieval time. The analytical model is useful to optimise the dimensions of the rack, assess the system throughput, and evaluate different storage policies.

Cobra: A content-based video retrieval system

NARCIS (Netherlands)

Petkovic, M.; Jonker, W.; Jensen, C.S.; Jeffery, K.G.; Pokorny, J.; Saltenis, S.; Bertino, E.; Böhm, K.; Jarke, M.

2002-01-01

An increasing number of large publicly available video libraries results in a demand for techniques that can manipulate the video data based on content. In this paper, we present a content-based video retrieval system called Cobra. The system supports automatic extraction and retrieval of high-level

Automated information retrieval system for radioactivation analysis

International Nuclear Information System (INIS)

Lambrev, V.G.; Bochkov, P.E.; Gorokhov, S.A.; Nekrasov, V.V.; Tolstikova, L.I.

1981-01-01

An automated information retrieval system for radioactivation analysis has been developed. An ES-1022 computer and a problem-oriented software ''The description information search system'' were used for the purpose. Main aspects and sources of forming the system information fund, characteristics of the information retrieval language of the system are reported and examples of question-answer dialogue are given. Two modes can be used: selective information distribution and retrospective search [ru

Content Based Retrieval System for Magnetic Resonance Images

International Nuclear Information System (INIS)

Trojachanets, Katarina

2010-01-01

The amount of medical images is continuously increasing as a consequence of the constant growth and development of techniques for digital image acquisition. Manual annotation and description of each image is impractical, expensive and time consuming approach. Moreover, it is an imprecise and insufficient way for describing all information stored in medical images. This induces the necessity for developing efficient image storage, annotation and retrieval systems. Content based image retrieval (CBIR) emerges as an efficient approach for digital image retrieval from large databases. It includes two phases. In the first phase, the visual content of the image is analyzed and the feature extraction process is performed. An appropriate descriptor, namely, feature vector is then associated with each image. These descriptors are used in the second phase, i.e. the retrieval process. With the aim to improve the efficiency and precision of the content based image retrieval systems, feature extraction and automatic image annotation techniques are subject of continuous researches and development. Including the classification techniques in the retrieval process enables automatic image annotation in an existing CBIR system. It contributes to more efficient and easier image organization in the system.Applying content based retrieval in the field of magnetic resonance is a big challenge. Magnetic resonance imaging is an image based diagnostic technique which is widely used in medical environment. According to this, the number of magnetic resonance images is enormously growing. Magnetic resonance images provide plentiful medical information, high resolution and specific nature. Thus, the capability of CBIR systems for image retrieval from large database is of great importance for efficient analysis of this kind of images. The aim of this thesis is to propose content based retrieval system architecture for magnetic resonance images. To provide the system efficiency, feature

A content-based news video retrieval system: NVRS

Science.gov (United States)

Liu, Huayong; He, Tingting

2009-10-01

This paper focus on TV news programs and design a content-based news video browsing and retrieval system, NVRS, which is convenient for users to fast browsing and retrieving news video by different categories such as political, finance, amusement, etc. Combining audiovisual features and caption text information, the system automatically segments a complete news program into separate news stories. NVRS supports keyword-based news story retrieval, category-based news story browsing and generates key-frame-based video abstract for each story. Experiments show that the method of story segmentation is effective and the retrieval is also efficient.

Data retrieval systems and models of information situations

International Nuclear Information System (INIS)

Jankowski, L.

1984-01-01

Demands placed on data retrieval systems and their basic parameters are given. According to the stage of development of data collection and processing, data retrieval systems may be divided into systems for the simple recording and provision of data, systems for recording and providing data with integrated statistical functions, and logical information systems. The structure is characterized of the said information systems as are methods of processing and representation of facts. The notion is defined of ''artificial intelligence'' in the development of logical information systems. The structure of representing knowledge in diverse forms of the model is decisive in logical information systems related to nuclear research. The main model elements are the characteristics of data, forms of representation and program. In dependence on the structure of data, the structure of the preparatory and transformation algorithms and on the aim of the system it is possible to classify data retrieval systems related to nuclear research and technology into five logical information models: linear, identification, advisory, theory-experiment models and problem solving models. The characteristics are given of the said models and examples of data retrieval systems for the individual models. (E.S.)

Hanford Site Tank 241-C-108 Residual Waste Contaminant Release Models and Supporting Data

Energy Technology Data Exchange (ETDEWEB)

Cantrell, Kirk J.; Krupka, Kenneth M.; Geiszler, Keith N.; Arey, Bruce W.; Schaef, Herbert T.

2010-06-18

This report presents the results of laboratory characterization, testing, and analysis for a composite sample (designated 20578) of residual waste collected from single-shell tank C-108 during the waste retrieval process after modified sluicing. These studies were completed to characterize concentration and form of contaminant of interest in the residual waste; assess the leachability of contaminants from the solids; and develop release models for contaminants of interest. Because modified sluicing did not achieve 99% removal of the waste, it is expected that additional retrieval processing will take place. As a result, the sample analyzed here is not expected to represent final retrieval sample.

STATUS/IQ: A Semi-Intelligent Information Retrieval System.

Science.gov (United States)

Pearsall, Jayne

1990-01-01

Provides background on the problems of traditional text retrieval systems and describes STATUS/IQ, an advanced text retrieval system that incorporates a natural language front-end and an advanced relevance ranking facility. The principles, capabilities, and benefits of the system are discussed, and an example of a STATUS/IQ session is presented…

HANFORD TANK CLEANUP UPDATE MAY 2009

International Nuclear Information System (INIS)

Holloway, J.N.

2009-01-01

Retrieval of waste from single-shell tank C-110 resumed in January making it the first waste retrieval operation for WRPS since taking over Hanford's Tank Operations Contract last October. Now, with approximately 90 percent of the waste removed, WRPS believes that modified sluicing has reached the limits of the technology to remove any further waste and is preparing documentation for use in decision making about any future retrieval actions. Tank C-110 is located in C Fann near the center of the Hanford Site. It is a 530,000 gallon tank, built in 1946, and held approximately 126,000 gallons of sludge and other radioactive and chemical waste materials when retrieval resumed. Modified sluicing technology uses liquid waste from a nearby double-shell tank to break up, dissolve and mobilize the solid material so it can be pumped. Because of the variety of waste fon11S, sluicing is often not able to remove all of the waste. The remaining waste will next be sampled for analysis, and results will be used to guide decisions regarding future actions. Work is moving rapidly in preparation to retrieve waste from a second single-shell tank this summer and transfer it to safer double-shell tank storage. Construction activities necessary to retrieve waste from Tank C-104, a 530,000 gallon tank built in 1943, are approximately 60 percent complete as WRPS maintains its focus on reducing the risk posed by Hanford's aging single-shell waste tanks. C-104 is one of Hanford's oldest radioactive and chemical waste storage tanks, containing approximately 263,000 gallons of wet sludge with a top layer that is dry and powdery. This will be the largest sludge volume retrieval ever attempted using modified sluicing technology. Modified sluicing uses high pressure water or liquid radioactive waste sprayed from nozzles above the waste. The liquid dissolves and/or mobilizes the waste so it can be pumped. In addition to other challenges, tank C-104 contains a significant amount of plutonium and

Design and Realization of Music Retrieval System Based on Feature Content

Directory of Open Access Journals (Sweden)

Li Lei

2015-01-01

Full Text Available As computer technology develops rapidly, retrieval systems have also undergone great changes. People are no longer contented with singular retrieval means, but are trying many other ways to retrieve feature content. When it comes to music, however, the complexity of sound is still preventing its retrieval from moving further forward. To solve this problem, systematic analysis and study is carried out on music retrieval system based on feature content. A music retrieval system model based on feature content consisting of technical approaches for processing and retrieving of extraction symbols of music feature content is built and realized. An SML model is proposed and tested on two different types of song sets. The result shows good performance of the system. Besides, the shortfalls of the model are also noted and the future prospects of the music retrieval system based on feature content are outlined.

An inversion of the estuarine circulation by sluice water discharge and its impact on suspended sediment transport

Science.gov (United States)

Schulz, Kirstin; Gerkema, Theo

2018-01-01

The Wadden Sea is characterized by a complex topography of branching channels and intertidal flats, in which the interplay between fresh water discharges, wind forcing and the tidal current causes sediment transport rates and direction to be highly variable in space and time. During three field campaigns, indications of a negative estuarine circulation have been found in a channel adjacent to the coast in the Western Dutch Wadden Sea. Contrary to the classical picture of estuarine circulation, a periodic density stratification was observed that builds up during flood and breaks down during ebb. This can be related to a large freshwater source at the mouth of the channel, the sluice in Kornwerderzand. In this study, observations of this phenomenon are presented, and with the help of a numerical model the different drivers for residual suspended matter transport in this area, namely tidal asymmetries in the current velocity and the above mentioned periodic stratification, are investigated. It is found that the residual current in the area of interest points in ebb direction, caused by both the elongated ebb flow phase and the periodic stratification. On the contrary, the stronger flood currents cause a transport of suspended matter in flood direction. This transport is counteracted and therefore diminished by the effects of the sluice discharge.

JINR information retrieval system

International Nuclear Information System (INIS)

Arnaudov, D.D.; Govorun, N.N.

1975-01-01

The organization of the main files of the JINR Information Retrieval System is described. There are four main files in the System. They are as follows: MD file that consists of abstracts of documents; OMPOD file where the index records of documents are gathered; MZD file that consists of list heads, and OMD file- the file of descriptors. The last three files are considered in some detail. The System is realized in the COBOL language on the CDC computer

Information retrieval system based on INIS tapes

International Nuclear Information System (INIS)

Pultorak, G.

1976-01-01

An information retrieval system based on the INIS computer tapes is described. It includes the three main elements of a computerized information system: a data base on a machine -readable medium, a collection of queries which represent the information needs from the data - base, and a set of programs by which the actual retrieval is done, according to the user's queries. The system is built for the center's computer, a CDC 3600, and its special features characterize, to a certain degree, the structure of the programs. (author)

Development of GPS data remote retrieval system using wireless LAN

Directory of Open Access Journals (Sweden)

Koichiro Doi

2012-11-01

Full Text Available A remote retrieval system, using a wireless LAN, was developed to retrieve dual-frequency GPS data. The system consists of a ground observation unit (comprising a dual-frequency GPS logger and a data transmission unit and a data retrieval unit. In this system, we use the ZigBee communication protocol to transmit control commands (2.4 GHz, 250 Kbps and a wireless LAN communication to transmit GPS data (2.4 GHz, 54 Mbps. Data of every 30 seconds to transmit to the data retrieval unit are re-sampled from 1-second data at 00 UT each day. We conducted three data-transmission tests with the system: (1 a ground data retrieval test, (2 a data retrieval test from the atmosphere of a few hundred meters high using a small unmanned aircraft, and (3 actual GPS-data retrieval tests from a GPS buoy deployed on sea ice at Nisi-no-ura Cove, Syowa Station, Antarctica. In test (1, we successfully received all the data from the ground observation unit when situated at distances of less than 400 m from the data retrieval unit. In test (2, we obtained approximately 24.5 MB of data from the aircraft at heights of less than 250 m. In test (3, we obtained approximately 23.5 MB of data from the GPS buoy within 10 minutes. The proposed system has the advantage of enabling continuous measurements without aborting the measurement at the data retrievals.

A visual retrieval environment for hypermedia information system

Energy Technology Data Exchange (ETDEWEB)

Lucarella, D; Zanzi, A [ENEL s.p.a., Centro Ricerca di Automatica, Cologno Monzese, Milan (Italy)

1995-03-01

The authors a graph-based object model that may be used as a uniform framework for direct manipulation of multimedia information. After an introduction motivating the need for abstraction and structuring mechanisms in hypermedia systems, the authors introduce the data model and the notion of perspective, a form of data abstraction that acts as a user interface to the system, providing control over the visibility of the objects and their properties. A perspective is defined to include an intention and an extension. The authors present a visual retrieval environment that effectively combines filtering, browsing, and navigation to provide an integrated view of the retrieval problem. Design and implementation issues are outlined for MORE (Multimedia Object Retrieval Environment), a prototype system relying on the proposed model. The focus is on the main user interface functionalities, and actual interaction sessions are presented including schema creation, information loading, and information retrieval

Retrieval System for Calcined Waste for the Idaho Cleanup Project - 12104

Energy Technology Data Exchange (ETDEWEB)

Eastman, Randy L.; Johnston, Beau A.; Lower, Danielle E. [CH2M-WG Idaho, LLC. The Idaho Cleanup Project at the Idaho National Laboratory (United States)

2012-07-01

This paper describes the conceptual approach to retrieve radioactive calcine waste, hereafter called calcine, from stainless steel storage bins contained within concrete vaults. The retrieval system will allow evacuation of the granular solids (calcine) from the storage bins through the use of stationary vacuum nozzles. The nozzles will use air jets for calcine fluidization and will be able to rotate and direct the fluidization or displacement of the calcine within the bin. Each bin will have a single retrieval system installed prior to operation to prevent worker exposure to the high radiation fields. The addition of an articulated camera arm will allow for operations monitoring and will be equipped with contingency tools to aid in calcine removal. Possible challenges (calcine bridging and rat-holing) associated with calcine retrieval and transport, including potential solutions for bin pressurization, calcine fluidization and waste confinement, are also addressed. The Calcine Disposition Project has the responsibility to retrieve, treat, and package HLW calcine. The calcine retrieval system has been designed to incorporate the functions and technical characteristics as established by the retrieval system functional analysis. By adequately implementing the highest ranking technical characteristics into the design of the retrieval system, the system will be able to satisfy the functional requirements. The retrieval system conceptual design provides the means for removing bulk calcine from the bins of the CSSF vaults. Top-down vacuum retrieval coupled with an articulating camera arm will allow for a robust, contained process capable of evacuating bulk calcine from bins and transporting it to the processing facility. The system is designed to fluidize, vacuum, transport and direct the calcine from its current location to the CSSF roof-top transport lines. An articulating camera arm, deployed through an adjacent access riser, will work in conjunction with the

Cognitive Process as a Basis for Intelligent Retrieval Systems Design.

Science.gov (United States)

Chen, Hsinchun; Dhar, Vasant

1991-01-01

Two studies of the cognitive processes involved in online document-based information retrieval were conducted. These studies led to the development of five computational models of online document retrieval which were incorporated into the design of an "intelligent" document-based retrieval system. Both the system and the broader implications of…

Database, expert systems, information retrieval

International Nuclear Information System (INIS)

Fedele, P.; Grandoni, G.; Mammarella, M.C.

1989-12-01

The great debate concerning the Italian high-school reform has induced a ferment of activity among the most interested and sensible of people. This was clearly demonstrated by the course 'Innovazione metodologico-didattica e tecnologie informatiche' organized for the staff of the 'lstituto Professionale L. Einaudi' of Lamezia Terme. The course was an interesting opportunity for discussions and interaction between the world of School and computer technology used in the Research field. This three day course included theoretical and practical lessons, showing computer facilities that could be useful for teaching. During the practical lessons some computer tools were presented from the very simple Electronic Sheets to the more complicated information Retrieval on CD-ROM interactive realizations. The main topics will be discussed later. They are: Modelling, Data Base, Integrated Information Systems, Expert Systems, Information Retrieval. (author)

45 CFR 205.35 - Mechanized claims processing and information retrieval systems; definitions.

Science.gov (United States)

2010-10-01

... claims processing and information retrieval systems; definitions. Section 205.35 through 205.38 contain...: (a) A mechanized claims processing and information retrieval system, hereafter referred to as an automated application processing and information retrieval system (APIRS), or the system, means a system of...

BIBLIO: A Computerized Retrieval System for Communication Education.

Science.gov (United States)

Williams, M. Lee; Edwards, Renee

1983-01-01

Describes BIBLIO, a computer program created for the storage and retrieval of articles in the 1970-80 issues of "Communication Education." Tells how articles were coded, method used to retrieve information, and advantages and uses of the system. (PD)

The Use of QBIC Content-Based Image Retrieval System

Directory of Open Access Journals (Sweden)

Ching-Yi Wu

2004-03-01

Full Text Available The fast increase in digital images has caught increasing attention on the development of image retrieval technologies. Content-based image retrieval (CBIR has become an important approach in retrieving image data from a large collection. This article reports our results on the use and users study of a CBIR system. Thirty-eight students majored in art and design were invited to use the IBM’s OBIC (Query by Image Content system through the Internet. Data from their information needs, behaviors, and retrieval strategies were collected through an in-depth interview, observation, and self-described think-aloud process. Important conclusions are:（1）There are four types of information needs for image data: implicit, inspirational, ever-changing, and purposive. The types of needs may change during the retrieval process. （2）CBIR is suitable for the example-type query, text retrieval is suitable for the scenario-type query, and image browsing is suitable for the symbolic query. （3）Different from text retrieval, detailed description of the query condition may lead to retrieval failure more easily. （4）CBIR is suitable for the domain-specific image collection, not for the images on the Word-Wide Web.[Article content in Chinese

Bird casualties and wind turbines near the Kreekrak sluices of Zeeland

International Nuclear Information System (INIS)

Musters, C.J.M.; Noordervliet, M.A.W.; Ter Keurs, W.J.

1995-03-01

The impact of wind turbines on birds was investigated for an estuary, situated near the North Sea coast in the Dutch province of Zeeland, with large amount of bird migration. Five 250 kW, three-bladed 25m, 40 rpm turbines were installed on the western side of a dike. The distance between the turbines is 125 m. Since 1 April 1990 the turbines have been in action almost continuously. The study on the title subject was set up to investigate the number of bird casualties caused by the five wind turbines near the sluices of Kreekrak and the number that may be expected to be caused by a total of 20 turbines. The study also focused on the number of casualties among rare birds in relation to those among the common birds as a result of the wind turbines in the Kreekrak area. An area of 125 x 125 m around each wind turbine, consisting partly of land and partly of water, was searched for dead birds every other day during a period of one year (28 April 1990 - 29 April 1991). During this one-year period, the bodies of 26 birds of 17 different species were found; six birds were certainly or almost certainly killed by the turbines. In three other cases, the birds may have died because of the turbines, while in the case of eight birds, it was not possible to determine the cause of death. The remaining nine birds were not killed by the wind turbines. The annual number of bird victims expected following the installation of 20 wind turbines was estimated at a minimum of 7 and a maximum of 142. For each species a correlation was found between the number of victims and the estimated number of visitors to the area. This suggests that the rare species among the birds were not excessively endangered by the turbines. The number of bird casualties per turbine was low in comparison with the results of other Dutch investigations. On the basis of these results, it is concluded that there is no reason to advise against increasing the number of wind turbines near the sluices of Kreekrak to 20. 3

Delve: A Data Set Retrieval and Document Analysis System

KAUST Repository

Akujuobi, Uchenna Thankgod

2017-12-29

Academic search engines (e.g., Google scholar or Microsoft academic) provide a medium for retrieving various information on scholarly documents. However, most of these popular scholarly search engines overlook the area of data set retrieval, which should provide information on relevant data sets used for academic research. Due to the increasing volume of publications, it has become a challenging task to locate suitable data sets on a particular research area for benchmarking or evaluations. We propose Delve, a web-based system for data set retrieval and document analysis. This system is different from other scholarly search engines as it provides a medium for both data set retrieval and real time visual exploration and analysis of data sets and documents.

An Integrated Information Retrieval Support System for Campus Network

Institute of Scientific and Technical Information of China (English)

无

2006-01-01

This paper presents a new integrated information retrieval support system (IIRSS) which can help Web search engines retrieve cross-lingual information from heterogeneous resources stored in multi-databases in Intranet. The IIRSS, with a three-layer architecture, can cooperate with other application servers running in Intranet. By using intelligent agents to collect information and to create indexes on-the-fly, using an access control strategy to confine a user to browsing those accessible documents for him/her through a single portal, and using a new cross-lingual translation tool to help the search engine retrieve documents, the new system provides controllable information access with different authorizations, personalized services, and real-time information retrieval.

Project Management Plan for Initial Tank Retrieval Systems, Project W-211

International Nuclear Information System (INIS)

VAN BEEK, J.E.

1999-01-01

Project W-211, Initial Tank Retrieval Systems (ITRS), is a fiscal year 1994 Major Systems Acquisition that will provide systems for retrieval of radioactive wastes from selected double-shell tanks (DST). The contents of these tanks are a combination of supernatant liquids and settled solids. To retrieve waste from the tanks, it is first necessary to mix the liquid and solids prior to transferring the slurry to alternative storage or treatment facilities. The ITRS will provide systems to mobilize the settled solids and transfer the wastes out of the tanks. In so doing, ITRS provides feed for future processing plants, allows for consolidation of tank solids to manage space within existing DST storage capacity, and supports continued safe storage of tank waste. The ITRS scope has been revised to include waste retrieval systems for tanks AP-102, AP-104, AP-108, AN-103, AN-104, AN-105, AY-102, AZ-102, and SY-102. This current tank selection and sequence provides retrieval systems supporting the Privatized waste processing plant and sustains the ability to provide final remediation of several watch list DSTs via treatment. The ITRS is configured to support changing program needs, as constrained by available budget, by maintaining the flexibility for exchanging tanks requiring mixer pump-based retrieval systems and shifting the retrieval sequence. Preliminary design was configured such that an adequate basis exists for initiating Title II design of a mixer pump based retrieval system for any DST. This Project Management Plan (PMP) documents the methodology for managing the ITRS, formalizes organizational responsibilities and interfaces, and identifies project requirements such as change control, design verification, systems engineering, and human factors engineering

Content-aware network storage system supporting metadata retrieval

Science.gov (United States)

Liu, Ke; Qin, Leihua; Zhou, Jingli; Nie, Xuejun

2008-12-01

Nowadays, content-based network storage has become the hot research spot of academy and corporation[1]. In order to solve the problem of hit rate decline causing by migration and achieve the content-based query, we exploit a new content-aware storage system which supports metadata retrieval to improve the query performance. Firstly, we extend the SCSI command descriptor block to enable system understand those self-defined query requests. Secondly, the extracted metadata is encoded by extensible markup language to improve the universality. Thirdly, according to the demand of information lifecycle management (ILM), we store those data in different storage level and use corresponding query strategy to retrieval them. Fourthly, as the file content identifier plays an important role in locating data and calculating block correlation, we use it to fetch files and sort query results through friendly user interface. Finally, the experiments indicate that the retrieval strategy and sort algorithm have enhanced the retrieval efficiency and precision.

A Prototype of an Intelligent System for Information Retrieval: IOTA.

Science.gov (United States)

Chiaramella, Y.; Defude, B.

1987-01-01

Discusses expert systems and their value as components of information retrieval systems related to semantic inference, and describes IOTA, a model of an intelligent information retrieval system which emphasizes natural language query processing. Experimental results are discussed and current and future developments are highlighted. (Author/LRW)

Endovascular retrieval of a CardioMEMS heart failure system

Directory of Open Access Journals (Sweden)

Arun Reghunathan, MD

2018-04-01

Full Text Available As the creation and utilization of new implantable devices increases, so does the need for interventionalists to devise unique retrieval mechanisms. This report describes the first endovascular retrieval of a CardioMEMS heart failure monitoring device. A 20-mm gooseneck snare was utilized in conjunction with a 9-French sheath and Envoy catheter for retrieval. The patient suffered no immediate postprocedural complications but died 5 days after the procedure from multiorgan failure secondary to sepsis. Keywords: CardioMEMS heart failure system, Endovascular retrieval

The JPL Library information retrieval system

Science.gov (United States)

Walsh, J.

1975-01-01

The development, capabilities, and products of the computer-based retrieval system of the Jet Propulsion Laboratory Library are described. The system handles books and documents, produces a book catalog, and provides a machine search capability. Programs and documentation are available to the public through NASA's computer software dissemination program.

Information retrieval system of nuclear power plant database (PPD) user's guide

International Nuclear Information System (INIS)

Izumi, Fumio; Horikami, Kunihiko; Kobayashi, Kensuke.

1990-12-01

A nuclear power plant database (PPD) and its retrieval system have been developed. The database involves a large number of safety design data of nuclear power plants, operating and planned in Japan. The information stored in the database can be retrieved at high speed, whenever they are needed, by use of the retrieval system. The report is a user's manual of the system to access the database utilizing a display unit of the JAERI computer network system. (author)

Remote Handled Transuranic Sludge Retrieval Transfer And Storage System At Hanford

International Nuclear Information System (INIS)

Raymond, Rick E.; Frederickson, James R.; Criddle, James; Hamilton, Dennis; Johnson, Mike W.

2012-01-01

This paper describes the systems developed for processing and interim storage of the sludge managed as remote-handled transuranic (RH-TRU). An experienced, integrated CH2M HILL/AFS team was formed to design and build systems to retrieve, interim store, and treat for disposal the K West Basin sludge, namely the Sludge Treatment Project (STP). A system has been designed and is being constructed for retrieval and interim storage, namely the Engineered Container Retrieval, Transfer and Storage System (ECRTS)

Remote Handled Transuranic Sludge Retrieval Transfer And Storage System At Hanford

Energy Technology Data Exchange (ETDEWEB)

Raymond, Rick E. [CH2M HILL Plateau Remediation Company, Richland, WA (United States); Frederickson, James R. [AREVA, Avignon (France); Criddle, James [AREVA, Avignon (France); Hamilton, Dennis [CH2M HILL Plateau Remediation Company, Richland, WA (United States); Johnson, Mike W. [CH2M HILL Plateau Remediation Company, Richland, WA (United States)

2012-10-18

This paper describes the systems developed for processing and interim storage of the sludge managed as remote-handled transuranic (RH-TRU). An experienced, integrated CH2M HILL/AFS team was formed to design and build systems to retrieve, interim store, and treat for disposal the K West Basin sludge, namely the Sludge Treatment Project (STP). A system has been designed and is being constructed for retrieval and interim storage, namely the Engineered Container Retrieval, Transfer and Storage System (ECRTS).

AP-102/104 Retrieval control system qualification test procedure

International Nuclear Information System (INIS)

RIECK, C.A.

1999-01-01

This Qualification Test Procedure documents the results of the qualification testing that was performed on the Project W-211, ''Initial Tank Retrieval Systems,'' retrieval control system (RCS) for tanks 241-AP-102 and 241-AP-104. The results confirm that the RCS has been programmed correctly and that the two related hardware enclosures have been assembled in accordance with the design documents

Information Retrieval and Criticality in Parity-Time-Symmetric Systems.

Science.gov (United States)

Kawabata, Kohei; Ashida, Yuto; Ueda, Masahito

2017-11-10

By investigating information flow between a general parity-time (PT-)symmetric non-Hermitian system and an environment, we find that the complete information retrieval from the environment can be achieved in the PT-unbroken phase, whereas no information can be retrieved in the PT-broken phase. The PT-transition point thus marks the reversible-irreversible criticality of information flow, around which many physical quantities such as the recurrence time and the distinguishability between quantum states exhibit power-law behavior. Moreover, by embedding a PT-symmetric system into a larger Hilbert space so that the entire system obeys unitary dynamics, we reveal that behind the information retrieval lies a hidden entangled partner protected by PT symmetry. Possible experimental situations are also discussed.

Maintenance study for W-340 Waste Retrieval System

International Nuclear Information System (INIS)

Christensen, C.; Conner, C.C.; Sekot, J.P.

1994-05-01

This study was performed to identify attributes and maintainability requirements for the Tank Waste Retrieval System (TWRS). The system will be developed for Westinghouse Hanford Company in Richland, Washington, as an integrated system to perform waste removal in Tank C-106 and, thus, demonstrate technologies for tank remediation that will satisfy requirements of the Tri-Party Agreement. The study examines attributes of the TWRS, scope of maintenance operations required for the TWRS, maintenance requirements, and potential methods of performing maintenance functions. Recommendations are provided for consideration in the development of both the conceptual design and performance specification, which will be used in procuring the W-340 Waste Retrieval System

ADEM - a system for recording and retrieving AECB decision-making

Energy Technology Data Exchange (ETDEWEB)

Beare, J W

1995-04-01

A concept and plan is proposed for a system to record on-going decision-making by the AECB so that the decision-making can be retrieved in the future. The system could also be used to retrieve past decision-making. (author). 4 tabs., 1 fig.

ADEM - a system for recording and retrieving AECB decision-making

International Nuclear Information System (INIS)

Beare, J.W.

1995-04-01

A concept and plan is proposed for a system to record on-going decision-making by the AECB so that the decision-making can be retrieved in the future. The system could also be used to retrieve past decision-making. (author). 4 tabs., 1 fig

An Intelligent System for Document Retrieval in Distributed Office Environments.

Science.gov (United States)

Mukhopadhyay, Uttam; And Others

1986-01-01

MINDS (Multiple Intelligent Node Document Servers) is a distributed system of knowledge-based query engines for efficiently retrieving multimedia documents in an office environment of distributed workstations. By learning document distribution patterns and user interests and preferences during system usage, it customizes document retrievals for…

Initial Single-Shell Tank Retrieval System mission analysis report

International Nuclear Information System (INIS)

Hertzel, J.S.

1996-03-01

This document provides the mission analysis for the Initial Single-Shell Tank Retrieval System task, which supports the Single-Shell Tank Waste Retrieval Program in its commitment to remove waste from single-shell tanks for treatment and final closure

Database, expert systems, information retrieval; Banche dati, sistemi esperti e information retrieval

Energy Technology Data Exchange (ETDEWEB)

Fedele, P; Grandoni, G; Mammarella, M C [ENEA - Dipartimento Protezione Ambientale e Salute dell' Uomo, Centro Ricerche Energia, Casaccia (Italy)

1989-12-15

The great debate concerning the Italian high-school reform has induced a ferment of activity among the most interested and sensible of people. This was clearly demonstrated by the course 'Innovazione metodologico-didattica e tecnologie informatiche' organized for the staff of the 'lstituto Professionale L. Einaudi' of Lamezia Terme. The course was an interesting opportunity for discussions and interaction between the world of School and computer technology used in the Research field. This three day course included theoretical and practical lessons, showing computer facilities that could be useful for teaching. During the practical lessons some computer tools were presented from the very simple Electronic Sheets to the more complicated information Retrieval on CD-ROM interactive realizations. The main topics will be discussed later. They are: Modelling, Data Base, Integrated Information Systems, Expert Systems, Information Retrieval. (author)

Status of sorption information retrieval system

International Nuclear Information System (INIS)

Hostetler, D.D.; Serne, R.J.; Brandstetter, A.

1979-09-01

A Sorption Information Retrieval System (SIRS) is being designed to provide an efficient, computerized, data base for information on radionuclide sorption in geologic media. The data bank will include Kd values for a large number of radionuclides occurring in radioactive wastes originating from the commercial nuclear power industry. Kd values determined to date span several groundwater compositions and a wide variety of rock types and minerals. The data system will not only include Kd values, but also background information on the experiments themselves. This will allow the potential user to retrieve not only the Kd values of interest but also sufficient information to evaluate the accuracy and usefulness of the data. During FY-1979, the logic structure of the system was designed, the software programmed, the data categories selected, and the data format specified. About 40% of the approximately 5000 Kd experiments performed by the Waste Isolation Safety Assessment Program (WISAP) and its subcontractors during FY-1977 and FY-1978 have been evaluated, coded and keypunched. Additional software improvements and system testing are needed before the system will be fully operational. A workshop requested by the NEA was held to discuss potential internatioal participation in the data system

Affinity between information retrieval system and search topic

International Nuclear Information System (INIS)

Ebinuma, Yukio

1979-01-01

Ten search profiles are tested on the INIS system at the Japan Atomic Energy Research Institute. The results are plotted on recall-precision chart ranging from 100% recall to 100% precision. The curves are not purely systems-dependent nor search-dependent, and are determined substantially by the ''affinity'' between the system and the search topic. The curves are named ''Affinity curves of search topics with information retrieval systems'', and hence retrieval affinity factors are derived. They are obtained not only for individual search topics but also for averages in the system. By such a quantitative examination, the difference of affinity among search topics in a given system, that of the same search topic among various systems, and that of systems to the same group of search topics can be compared reasonably. (author)

A prompt information retrieval system on handheld devices

Science.gov (United States)

Huang, Yo-Ping; Yen, Wei; Lin, Shi-Hung

2007-04-01

In this paper, we propose an intelligent bird information retrieval system which aims to construct a mobility-learning activity under the up-to-date wireless technology. The system consists of a Tablet PC and PDAs with wireless networking capabilities. The PDA is equipped with a friendly retrieval interface and a good learning environment. In our system, users only need to click the buttons or input the keywords to retrieve bird information. Besides, users can discuss or share their information and knowledge via the wireless network. Our system saves bird information in four categories including "Introduction," "Images," "Sound," "Streaming Media," and "Ecological Memo." The integral knowledge helps users understand more about birds. Data mining and fuzzy association rules are applied to recommend users those birds they may be interested in. A streaming server on the Tablet PC is built to provide the streaming media for PDA users. By this way, PDA users can enjoy the multimedia from Tablet PC in real time without downloading completely. Finally, the system is a perfect tool for outdoor teaching and can be easily extended to provide navigation and touring services for national parks or museums.

AEROMETRIC INFORMATION RETRIEVAL SYSTEM (AIRS) - GRAPHICS

Science.gov (United States)

Aerometric Information Retrieval System (AIRS) is a computer-based repository of information about airborne pollution in the United States and various World Health Organization (WHO) member countries. AIRS is administered by the U.S. Environmental Protection Agency, and runs on t...

Project Execution Plan for Project W-211 Initial Tank Retrieval Systems (ITRS)

International Nuclear Information System (INIS)

VAN BEEK, J.E.

2000-01-01

This Project Execution Plan documents the methodology for managing Project W-211. Project W-211, Initial Tank Retrieval Systems (ITRS), is a fiscal year 1994 Major Systems Acquisition that will provide systems for retrieval of radioactive wastes from selected double-shell tanks (DST). The contents of these tanks are a combination of supernatant liquids and settled solids. To retrieve waste from the tanks, it is first necessary to mix the liquid and solids prior to transferring the slurry to alternative storage or treatment facilities. The ITRS will provide systems to mobilize the settled solids and transfer the wastes out of the tanks. In so doing, ITRS provides feed for the future waste treatment plant, allows for consolidation of tank solids to manage space within existing DST storage capacity, and supports continued safe storage of tank waste. The ITRS scope has been revised to include waste retrieval systems for tanks AP-102, AP-104, AN-102, AN-103, AN-104, AN-105, AY-102, AZ-102, and SY-102. This current tank selection and sequence provides retrieval systems supporting the River Protection Project (RF'P) Waste Treatment Facility and sustains the ability to provide final remediation of several watch list DSTs via treatment. The ITRS is configured to support changing program needs, as constrained by available budget, by maintaining the flexibility for exchanging tanks requiring mixer pump-based retrieval systems and shifting the retrieval sequence. Preliminary design was configured such that an adequate basis exists for initiating Title II design of a mixer pump-based retrieval system for any DST. This Project Execution Plan (PEP), derived from the predecessor Project Management Plan, documents the methodology for managing the ITRS, formalizes organizational responsibilities and interfaces, and identifies project requirements such as change control, design verification, systems engineering, and human factors engineering

Overlap in the functional neural systems involved in semantic and episodic memory retrieval.

Science.gov (United States)

Rajah, M N; McIntosh, A R

2005-03-01

Neuroimaging and neuropsychological data suggest that episodic and semantic memory may be mediated by distinct neural systems. However, an alternative perspective is that episodic and semantic memory represent different modes of processing within a single declarative memory system. To examine whether the multiple or the unitary system view better represents the data we conducted a network analysis using multivariate partial least squares (PLS ) activation analysis followed by covariance structural equation modeling (SEM) of positron emission tomography data obtained while healthy adults performed episodic and semantic verbal retrieval tasks. It is argued that if performance of episodic and semantic retrieval tasks are mediated by different memory systems, then there should differences in both regional activations and interregional correlations related to each type of retrieval task, respectively. The PLS results identified brain regions that were differentially active during episodic retrieval versus semantic retrieval. Regions that showed maximal differences in regional activity between episodic retrieval tasks were used to construct separate functional models for episodic and semantic retrieval. Omnibus tests of these functional models failed to find a significant difference across tasks for both functional models. The pattern of path coefficients for the episodic retrieval model were not different across tasks, nor were the path coefficients for the semantic retrieval model. The SEM results suggest that the same memory network/system was engaged across tasks, given the similarities in path coefficients. Therefore, activation differences between episodic and semantic retrieval may ref lect variation along a continuum of processing during task performance within the context of a single memory system.

Bibliographic Information Retrieval Systems: Increasing Cognitive Compatibility.

Science.gov (United States)

Smith, Philip J.; And Others

1987-01-01

Discusses the impact of research in artificial intelligence and human computer interaction on the design of bibliographic information retrieval systems, and presents design principles of a prototype system that uses semantically based searches and a knowledge base consisting of conceptual frames. (10 references) (CLB)

Predicting Document Retrieval System Performance: An Expected Precision Measure.

Science.gov (United States)

Losee, Robert M., Jr.

1987-01-01

Describes an expected precision (EP) measure designed to predict document retrieval performance. Highlights include decision theoretic models; precision and recall as measures of system performance; EP graphs; relevance feedback; and computing the retrieval status value of a document for two models, the Binary Independent Model and the Two Poisson…

Experimental evaluation of ontology-based HIV/AIDS frequently asked question retrieval system.

Science.gov (United States)

Ayalew, Yirsaw; Moeng, Barbara; Mosweunyane, Gontlafetse

2018-05-01

This study presents the results of experimental evaluations of an ontology-based frequently asked question retrieval system in the domain of HIV and AIDS. The main purpose of the system is to provide answers to questions on HIV/AIDS using ontology. To evaluate the effectiveness of the frequently asked question retrieval system, we conducted two experiments. The first experiment focused on the evaluation of the quality of the ontology we developed using the OQuaRE evaluation framework which is based on software quality metrics and metrics designed for ontology quality evaluation. The second experiment focused on evaluating the effectiveness of the ontology in retrieving relevant answers. For this we used an open-source information retrieval platform, Terrier, with retrieval models BM25 and PL2. For the measurement of performance, we used the measures mean average precision, mean reciprocal rank, and precision at 5. The results suggest that frequently asked question retrieval with ontology is more effective than frequently asked question retrieval without ontology in the domain of HIV/AIDS.

Operational test report for the AY-102 Enraf densitometer control and acquisition system

International Nuclear Information System (INIS)

Huber, J.H.

1998-01-01

On June 2 through June 10, 1998, the AY-102 Tank Densitometer Control and Acquisition System was operationally tested per OTP-320-01 O Revision A-O. The test was performed at the Department of Energy's Hanford Site, 200 East Area, 241-AY Tank Farm. The test validated the functionality of the Enraf 854 ATG Densitometer Gauge and Enraf Control Panel software for use by project W-320, Waste Retrieval Sluicing System (WRSS). The purpose of the test procedure was two fold: (1) to verify the functionality of the Enraf 854 ATG as a Densitometer and (2) to verify the functionality of the Enraf Control Panel Software density acquisition routines. The densitometer was previously acceptance tested per HNF-SD-WM-ATP-077. The software was previously acceptance tested per HNF-1991

A Fuzzy Semantic Information Retrieval System for Transactional Applications

Directory of Open Access Journals (Sweden)

A O Ajayi

2009-09-01

Full Text Available In this paper, we present an information retrieval system based on the concept of fuzzy logic to relate vague and uncertain objects with un-sharp boundaries. The simple but comprehensive user interface of the system permits the entering of uncertain specifications in query forms. The system was modelled and simulated in a Matlab environment; its implementation was carried out using Borland C++ Builder. The result of the performance measure of the system using precision and recall rates is encouraging. Similarly, the smaller amount of more precise information retrieved by the system will positively impact the response time perceived by the users.

JANE, A new information retrieval system for the Radiation Shielding Information Center

International Nuclear Information System (INIS)

Trubey, D.K.

1991-05-01

A new information storage and retrieval system has been developed for the Radiation Shielding Information Center (RSIC) at Oak Ridge National Laboratory to replace mainframe systems that have become obsolete. The database contains citations and abstracts of literature which were selected by RSIC analysts and indexed with terms from a controlled vocabulary. The database, begun in 1963, has been maintained continuously since that time. The new system, called JANE, incorporates automatic indexing techniques and on-line retrieval using the RSIC Data General Eclipse MV/4000 minicomputer, Automatic indexing and retrieval techniques based on fuzzy-set theory allow the presentation of results in order of Retrieval Status Value. The fuzzy-set membership function depends on term frequency in the titles and abstracts and on Term Discrimination Values which indicate the resolving power of the individual terms. These values are determined by the Cover Coefficient method. The use of a commercial database base to store and retrieve the indexing information permits rapid retrieval of the stored documents. Comparisons of the new and presently-used systems for actual searches of the literature indicate that it is practical to replace the mainframe systems with a minicomputer system similar to the present version of JANE. 18 refs., 10 figs

Management-retrieval code system of fission barrier parameter sub-library

International Nuclear Information System (INIS)

Zhang Limin; Su Zongdi; Ge Zhigang

1995-01-01

The fission barrier parameter (FBP) library, which is a sub-library of Chinese Evaluated Nuclear Parameter library (CENPL), stores various popular used fission barrier parameters from different historical period, and could retrieve the required fission barrier parameters by using the management retrieval code system of the FBP sub-library. The function, feature and operation instruction of the code system are described briefly

A humming retrieval system based on music fingerprint

Science.gov (United States)

Han, Xingkai; Cao, Baiyu

2011-10-01

In this paper, we proposed an improved music information retrieval method utilizing the music fingerprint. The goal of this method is to represent the music with compressed musical information. Based on the selected MIDI files, which are generated automatically as our music target database, we evaluate the accuracy, effectiveness, and efficiency of this method. In this research we not only extract the feature sequence, which can represent the file effectively, from the query and melody database, but also make it possible for retrieving the results in an innovative way. We investigate on the influence of noise to the performance of our system. As experimental result shows, the retrieval accuracy arriving at up to91% without noise is pretty well

Development of nuclear reaction data retrieval system on Meme media

International Nuclear Information System (INIS)

Ohbayasi, Yosihide; Masui, Hiroshi; Aoyama, Shigeyoshi; Kato, Kiyoshi; Chiba, Masaki

2000-01-01

A newly designed retrieval system of charged particle nuclear reaction data is developed on Meme media architecture. We designed the network-based (client-server) retrieval system. The server system is constructed on a UNIX workstation with a relational database, and the client system is constructed on Microsoft Windows PC using an IntelligentPad software package. The IntelligentPad is currently available as developing Meme media. We will develop the system to realize effective utilization of nuclear reaction data: I. 'Re-production, Re-edit, Re-use', II. 'Circulation, Coordination and Evolution', III. 'Knowledge discovery'. (author)

Database retrieval systems for nuclear and astronomical data

International Nuclear Information System (INIS)

Suda, Takuma; Korennov, Sergei; Otuka, Naohiko; Yamada, Shimako; Katsuta, Yutaka; Ohnishi, Akira; Kato, Kiyoshi; Fujimoto, Masayuki Y.

2006-01-01

Data retrieval and plot systems of nuclear and astronomical data are constructed on a common platform. Web-based systems will soon be opened to the users of both fields of nuclear physics and astronomy. (author)

Cooperative Telerobotic Retrieval system Phase 1 technology evaluation report

Energy Technology Data Exchange (ETDEWEB)

Hyde, R.A.; Croft, K.M.

1995-03-01

This document describes the results from the Cooperative Telerobotic Retrieval demonstration and testing conducted at the Idaho National Engineering Laboratory during December 1994 and January 1995. The purpose of the demonstration was to ascertain the feasibility of the system for deploying tools both independently and cooperatively for supporting remote characterization and removal of buried waste in a safe manner and in compliance with all regulatory requirements. The procedures and goals of the demonstration were previously defined in the Cooperative Telerobotic Retrieval System Test Plan for Fiscal Year 1994, which served as a guideline for evaluating the system.

EARS: An Online Bibliographic Search and Retrieval System Based on Ordered Explosion.

Science.gov (United States)

Ramesh, R.; Drury, Colin G.

1987-01-01

Provides overview of Ergonomics Abstracts Retrieval System (EARS), an online bibliographic search and retrieval system in the area of human factors engineering. Other online systems are described, the design of EARS based on inverted file organization is explained, and system expansions including a thesaurus are discussed. (Author/LRW)

SIGNIFICANT PROGRESS IN THE DEPLOYMENT OF NEW TECHNOLOGIES FOR THE RETRIEVAL OF HANFORD RADIOACTIVE WASTE STORAGE TANKS

International Nuclear Information System (INIS)

RAYMOND RE; DODD RA; CARPENTER KE; STURGES MH

2008-01-01

Significant enhancements in the development and deployment of new technologies for removing waste from storage tanks at the Hanford Site have resulted in accelerated progress and reduced costs for tank cleanup. CH2M HILL Hanford Group, Inc. is the U.S. Department of Energy, Office of River Protection's prime contractor responsible for safely storing and retrieving approximately 53 million gallons of highly-radioactive and hazardous waste stored in 177 underground tanks. The waste is stored in 149 older single-shell tanks (SST) and 28 newer double-shell tanks (DST) that are grouped in 18 so-called farms near the center of the Hanford Site, located in southeastern Washington State. Tank contents include materials from years of World-War II and post-war weapons production, which account for 60 percent by volume of the nation's high-level radioactive waste. A key strategy for improved cleanup is the development and deployment of innovative technologies, which enhance worker safety, resolve technical challenges, streamline retrieval processes, and cut project costs and durations. During the past seven years of tank cleanout projects we have encountered conditions and waste chemistry that defy conventional approaches, requiring a variety of new tools and techniques. Through the deployment of advanced technology and the creative application of resources, we are finding ways to accomplish the retrieval process safely, swiftly, and economically. To date, retrieval operations have been completed in seven tanks, including a record six tanks in a two-year period. Retrieval operations are in progress for another three tanks. This paper describes the following tank cleanup technologies deployed at Hanford in the past few years: Modified waste sluicing, High pressure water lance, Mobile retrieval tools, Saltcake dissolution, Vacuum retrieval, Sparging of wastes, Selective dissolution for waste treatment, Oxalic acid dissolution, High-pressure water mixers, Variable height pumps

Contingency plan for the Old Hydrofracture Facility tanks sluicing project at Oak Ridge National Laboratory, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

1996-10-01

Lockheed Martin Energy Systems, Inc. (Energy Systems), plans to begin a sluicing (flushing) and pumping project to remove the contents from five inactive, underground storage tanks at the Old Hydrofracture Facility (OHF) at the Oak Ridge National Laboratory (ORNL) in Oak Ridge, Tennessee. The tank contents will be transferred to the Melton Valley Storage Tanks, which are part of the active waste treatment system at ORNL. The purpose of the project is to minimize the risk of leaking the highly radioactive material to the environment. The five OHF tanks each contain a layer of sludge and a layer of supernatant. Based on a sampling project undertaken in 1995, the sludge in the tanks has been characterized as transuranic and mixed waste and the supernatants have been characterized as mixed waste. The combined radioactivity of the contents of the five tanks is approximately 29,500 Ci. This contingency plan is based on the preliminary design for the project and describes a series of potential accident/release scenarios for the project. It outlines Energy Systems' preliminary plans for prevention, detection, and mitigation. Prevention/detection methods range from using doubly contained pipelines to alarmed sensors and automatic pump cutoff systems. Plans for mitigation range from pumping leaked fluids from the built-in tank drainage systems and cleaning up spilled liquids to personnel evacuation

The Oklahoma Geographic Information Retrieval System

Science.gov (United States)

Blanchard, W. A.

1982-01-01

The Oklahoma Geographic Information Retrieval System (OGIRS) is a highly interactive data entry, storage, manipulation, and display software system for use with geographically referenced data. Although originally developed for a project concerned with coal strip mine reclamation, OGIRS is capable of handling any geographically referenced data for a variety of natural resource management applications. A special effort has been made to integrate remotely sensed data into the information system. The timeliness and synoptic coverage of satellite data are particularly useful attributes for inclusion into the geographic information system.

[Design and implementation of medical instrument standard information retrieval system based on APS.NET].

Science.gov (United States)

Yu, Kaijun

2010-07-01

This paper Analys the design goals of Medical Instrumentation standard information retrieval system. Based on the B /S structure,we established a medical instrumentation standard retrieval system with ASP.NET C # programming language, IIS f Web server, SQL Server 2000 database, in the. NET environment. The paper also Introduces the system structure, retrieval system modules, system development environment and detailed design of the system.

Repository of not readily available documents for project W-320

Energy Technology Data Exchange (ETDEWEB)

Conner, J.C.

1997-04-18

The purpose of this document is to provide a readily available source of the technical reports needed for the development of the safety documentation provided for the waste retrieval sluicing system (WRSS), designed to remove the radioactive and chemical sludge from tank 241-C-106, and transport that material to double-shell tank 241-AY-102 via a new, temporary, shielded, encased transfer line.

Repository of not readily available documents for project W-320

International Nuclear Information System (INIS)

Conner, J.C.

1997-01-01

The purpose of this document is to provide a readily available source of the technical reports needed for the development of the safety documentation provided for the waste retrieval sluicing system (WRSS), designed to remove the radioactive and chemical sludge from tank 241-C-106, and transport that material to double-shell tank 241-AY-102 via a new, temporary, shielded, encased transfer line

Blind phase retrieval for aberrated linear shift-invariant imaging systems

International Nuclear Information System (INIS)

Yu, Rotha P; Paganin, David M

2010-01-01

We develop a means to reconstruct an input complex coherent scalar wavefield, given a through focal series (TFS) of three intensity images output from a two-dimensional (2D) linear shift-invariant optical imaging system with unknown aberrations. This blind phase retrieval technique unites two methods, namely (i) TFS phase retrieval and (ii) iterative blind deconvolution. The efficacy of our blind phase retrieval procedure has been demonstrated using simulated data, for a variety of Poisson noise levels.

User centered and ontology based information retrieval system for life sciences.

Science.gov (United States)

Sy, Mohameth-François; Ranwez, Sylvie; Montmain, Jacky; Regnault, Armelle; Crampes, Michel; Ranwez, Vincent

2012-01-25

Because of the increasing number of electronic resources, designing efficient tools to retrieve and exploit them is a major challenge. Some improvements have been offered by semantic Web technologies and applications based on domain ontologies. In life science, for instance, the Gene Ontology is widely exploited in genomic applications and the Medical Subject Headings is the basis of biomedical publications indexation and information retrieval process proposed by PubMed. However current search engines suffer from two main drawbacks: there is limited user interaction with the list of retrieved resources and no explanation for their adequacy to the query is provided. Users may thus be confused by the selection and have no idea on how to adapt their queries so that the results match their expectations. This paper describes an information retrieval system that relies on domain ontology to widen the set of relevant documents that is retrieved and that uses a graphical rendering of query results to favor user interactions. Semantic proximities between ontology concepts and aggregating models are used to assess documents adequacy with respect to a query. The selection of documents is displayed in a semantic map to provide graphical indications that make explicit to what extent they match the user's query; this man/machine interface favors a more interactive and iterative exploration of data corpus, by facilitating query concepts weighting and visual explanation. We illustrate the benefit of using this information retrieval system on two case studies one of which aiming at collecting human genes related to transcription factors involved in hemopoiesis pathway. The ontology based information retrieval system described in this paper (OBIRS) is freely available at: http://www.ontotoolkit.mines-ales.fr/ObirsClient/. This environment is a first step towards a user centred application in which the system enlightens relevant information to provide decision help.

User centered and ontology based information retrieval system for life sciences

Directory of Open Access Journals (Sweden)

Sy Mohameth-François

2012-01-01

Full Text Available Abstract Background Because of the increasing number of electronic resources, designing efficient tools to retrieve and exploit them is a major challenge. Some improvements have been offered by semantic Web technologies and applications based on domain ontologies. In life science, for instance, the Gene Ontology is widely exploited in genomic applications and the Medical Subject Headings is the basis of biomedical publications indexation and information retrieval process proposed by PubMed. However current search engines suffer from two main drawbacks: there is limited user interaction with the list of retrieved resources and no explanation for their adequacy to the query is provided. Users may thus be confused by the selection and have no idea on how to adapt their queries so that the results match their expectations. Results This paper describes an information retrieval system that relies on domain ontology to widen the set of relevant documents that is retrieved and that uses a graphical rendering of query results to favor user interactions. Semantic proximities between ontology concepts and aggregating models are used to assess documents adequacy with respect to a query. The selection of documents is displayed in a semantic map to provide graphical indications that make explicit to what extent they match the user's query; this man/machine interface favors a more interactive and iterative exploration of data corpus, by facilitating query concepts weighting and visual explanation. We illustrate the benefit of using this information retrieval system on two case studies one of which aiming at collecting human genes related to transcription factors involved in hemopoiesis pathway. Conclusions The ontology based information retrieval system described in this paper (OBIRS is freely available at: http://www.ontotoolkit.mines-ales.fr/ObirsClient/. This environment is a first step towards a user centred application in which the system enlightens

Prototyping a Distributed Information Retrieval System That Uses Statistical Ranking.

Science.gov (United States)

Harman, Donna; And Others

1991-01-01

Built using a distributed architecture, this prototype distributed information retrieval system uses statistical ranking techniques to provide better service to the end user. Distributed architecture was shown to be a feasible alternative to centralized or CD-ROM information retrieval, and user testing of the ranking methodology showed both…

Distributed Systems and Applications of Information Filtering and Retrieval

CERN Document Server

Giuliani, Alessandro; Semeraro, Giovanni; DART 2012

2014-01-01

This volume focuses on new challenges in distributed Information Filtering and Retrieval. It collects invited chapters and extended research contributions from the special session on Information Filtering and Retrieval: Novel Distributed Systems and Applications (DART) of the 4th International Conference on Knowledge Discovery and Information Retrieval (KDIR 2012), held in Barcelona, Spain, on 4-7 October 2012. The main focus of DART was to discuss and compare suitable novel solutions based on intelligent techniques and applied to real-world applications. The chapters of this book present a comprehensive review of related works and state of the art. Authors, both practitioners and researchers, shared their results in several topics such as "Multi-Agent Systems", "Natural Language Processing", "Automatic Advertisement", "Customer Interaction Analytics", "Opinion Mining". Contributions have been careful reviewed by experts in the area, who also gave useful suggestions to improve the quality of the volume.

System for histogram entry, retrieval, and plotting

International Nuclear Information System (INIS)

Kellogg, M.; Gallup, J.M.; Shlaer, S.; Spencer, N.

1977-10-01

This manual describes the systems for producing histograms and dot plots that were designed for use in connection with the Q general-purpose data-acquisition system. These systems allow for the creation of histograms; the entry, retrieval, and plotting of data in the form of histograms; and the dynamic display of scatter plots as data are acquired. Although the systems are designed for use with Q, they can also be used as a part of other applications. 3 figures

DALIS: a computer-assisted document retrieval system for the FFTF

International Nuclear Information System (INIS)

Harves, W.G.

1981-01-01

The FFTF (Fast Flux Test Facility) is a liquid sodium cooled, fast flux reactor designed specifically for irradiation testing of fuels and components for liquid metal fast breeder reactors. The Department of Energy and the Nuclear Regulatory Commission require that all pertinent documentation for maintenance, operation, and safety of the FFTF be readily accessible and retrievable, both during initial startup and for the lifetime of the plant. That amounts to a lot of information which has to be retrievable. The indexing system finally developed is called the DALIS system, short for Document and Location Indexing System. This system was designed by an engineer (Michael Theo) for use by engineers. DALIS uses descriptiors and keywords to identify each document in the system. The descriptors give such information as document number, date of issuance of the document, the title, the originating organization, and the microfilm or hardcopy location of the document. The keywords are words or phrases that describe the content of the document and permit retrieval by means of a computer search for documents with the stated keywords

Preliminary safety equipment list for Tank 241-C-106 Manipulator Retrieval System, Project W-340

International Nuclear Information System (INIS)

Guthrie, R.L.

1994-01-01

This document identifies the anticipated safety classification of the estimated major subsystems, based on the projected major functions, that will be used as guidance for the development of the conceptual design of the Manipulator Retrieval System for Tank 241-C-106. This document is intended to be updated as the design of the Manipulator Retrieval System evolves through the conceptual and definitive design phases. The Manipulator Retrieval System is to be capable of removing the hardened sludge heel at the bottom of single shell Tank 241-C-106 and to perform an overall clean out of the tank that leaves a maximum of 360 ft 3 (TPA milestone M-45-00). The thickness of the heel prior to initiation of waste retrieval with the Manipulator Retrieval System is estimated to be 1- to 2-ft. The Manipulator Retrieval System is currently in the pre-conceptual phase with no definitive systems or subsystems. The anticipated retrieval functions for the Manipulator Retrieval System is based on Table 6-2 of WHC-SD-W340-ES-001, Rev. 1. Projected equipment to accomplish these functions were based on the following systems and equipment: Rotary Mode Core Sampling Equipment (WHC-SD-WM-SEL-032); Light Duty Utility Arm System Equipment (WHC-SD-WM-SEL-034); Single Shell Tanks Equipment (WHC-SD-WM-SEL-020)

An information retrieval system using weighted descriptors generated by automatic frequency counting

International Nuclear Information System (INIS)

Komatsubara, Yasutoshi

1979-01-01

An information retrieval system with improved relevance is described, in which a weighted descriptor file, generated by feedback of requester's relevance judgement on pretest results, is used. This method does not need modification of search formulas, and works better by only setting weight thresholds, and can alleviate searcher duties, as examples show. Index word weighting and retrieval word weighting are compared and some problems to be encountered when retrieval word weighting is combined to operational systems are pointed out. (author)

42 CFR 433.116 - FFP for operation of mechanized claims processing and information retrieval systems.

Science.gov (United States)

2010-10-01

... and information retrieval systems. 433.116 Section 433.116 Public Health CENTERS FOR MEDICARE... FISCAL ADMINISTRATION Mechanized Claims Processing and Information Retrieval Systems § 433.116 FFP for operation of mechanized claims processing and information retrieval systems. (a) Subject to 42 CFR 433.113(c...

Nonmaterialized Relations and the Support of Information Retrieval Applications by Relational Database Systems.

Science.gov (United States)

Lynch, Clifford A.

1991-01-01

Describes several aspects of the problem of supporting information retrieval system query requirements in the relational database management system (RDBMS) environment and proposes an extension to query processing called nonmaterialized relations. User interactions with information retrieval systems are discussed, and nonmaterialized relations are…

Associative conceptual space-based information retrieval systems

NARCIS (Netherlands)

M.J. Schuemie (Martijn); J.H. van den Berg (Jan)

1998-01-01

textabstractIn this `Information Era' with the availability of large collections of books, articles, journals, CD-ROMs, video films and so on, there exists an increasing need for intelligent information retrieval systems that enable users to find the information desired easily. Many attempts have

Project W-320, 241-C-106 sluicing: Piping calculations. Volume 8

International Nuclear Information System (INIS)

Bailey, J.W.

1998-01-01

This supporting document has been prepared to make the FDNW calculations for Project W-320 readily retrievable. The objective of this calculation is to perform the hydraulic analysis on the slurry line and the supernate line for W-320. This calculation will use the As-Built conditions of the slurry line and the supernate line. Booster Pump Curves vs System Curves shall be generated for the supernate system and the slurry system

A data storage, retrieval and analysis system for endocrine research. [for Skylab

Science.gov (United States)

Newton, L. E.; Johnston, D. A.

1975-01-01

This retrieval system builds, updates, retrieves, and performs basic statistical analyses on blood, urine, and diet parameters for the M071 and M073 Skylab and Apollo experiments. This system permits data entry from cards to build an indexed sequential file. Programs are easily modified for specialized analyses.

User interfaces of information retrieval systems and user friendliness

OpenAIRE

Polona Vilar; Maja Žumer

2008-01-01

The paper deals with the characteristics of user interfaces of information retrieval systems with the emphasis on design and evaluation. It presents users’ information retrieval tasks and the functions which are offered through interfaces. Design rules, guidelines and standards are presented, as well as criteria and methods for evaluation. Special emphasis is placed on the concept of user friendliness as one of the most important characteristic of the user interfaces. Various definitions of u...

Retrieval program system of Chinese Evaluated (frequently useful) Nuclear Decay Database

International Nuclear Information System (INIS)

Huang Xiaolong; Zhou Chunmei

1995-01-01

The Chinese Evaluated (frequently useful) Nuclear Decay Database has been set up in MICRO-VAX-11 computer at Chinese Nuclear Data Center (CNDC). For users' convenience, the retrieval program system of the database is written. Retrieval can be carried out for one nucleus or multi-nucleus. The retrieved results can be displayed on terminal screen or output to M3081 printer and laser printer in ENSDF format, table report or scheme diagrams

Annotation and retrieval system of CAD models based on functional semantics

Science.gov (United States)

Wang, Zhansong; Tian, Ling; Duan, Wenrui

2014-11-01

CAD model retrieval based on functional semantics is more significant than content-based 3D model retrieval during the mechanical conceptual design phase. However, relevant research is still not fully discussed. Therefore, a functional semantic-based CAD model annotation and retrieval method is proposed to support mechanical conceptual design and design reuse, inspire designer creativity through existing CAD models, shorten design cycle, and reduce costs. Firstly, the CAD model functional semantic ontology is constructed to formally represent the functional semantics of CAD models and describe the mechanical conceptual design space comprehensively and consistently. Secondly, an approach to represent CAD models as attributed adjacency graphs(AAG) is proposed. In this method, the geometry and topology data are extracted from STEP models. On the basis of AAG, the functional semantics of CAD models are annotated semi-automatically by matching CAD models that contain the partial features of which functional semantics have been annotated manually, thereby constructing CAD Model Repository that supports model retrieval based on functional semantics. Thirdly, a CAD model retrieval algorithm that supports multi-function extended retrieval is proposed to explore more potential creative design knowledge in the semantic level. Finally, a prototype system, called Functional Semantic-based CAD Model Annotation and Retrieval System(FSMARS), is implemented. A case demonstrates that FSMARS can successfully botain multiple potential CAD models that conform to the desired function. The proposed research addresses actual needs and presents a new way to acquire CAD models in the mechanical conceptual design phase.

Retrieval with Clustering in a Case-Based Reasoning System for Radiotherapy Treatment Planning

Science.gov (United States)

Khussainova, Gulmira; Petrovic, Sanja; Jagannathan, Rupa

2015-05-01

Radiotherapy treatment planning aims to deliver a sufficient radiation dose to cancerous tumour cells while sparing healthy organs in the tumour surrounding area. This is a trial and error process highly dependent on the medical staff's experience and knowledge. Case-Based Reasoning (CBR) is an artificial intelligence tool that uses past experiences to solve new problems. A CBR system has been developed to facilitate radiotherapy treatment planning for brain cancer. Given a new patient case the existing CBR system retrieves a similar case from an archive of successfully treated patient cases with the suggested treatment plan. The next step requires adaptation of the retrieved treatment plan to meet the specific demands of the new case. The CBR system was tested by medical physicists for the new patient cases. It was discovered that some of the retrieved cases were not suitable and could not be adapted for the new cases. This motivated us to revise the retrieval mechanism of the existing CBR system by adding a clustering stage that clusters cases based on their tumour positions. A number of well-known clustering methods were investigated and employed in the retrieval mechanism. Results using real world brain cancer patient cases have shown that the success rate of the new CBR retrieval is higher than that of the original system.

Retrieval with Clustering in a Case-Based Reasoning System for Radiotherapy Treatment Planning

International Nuclear Information System (INIS)

Khussainova, Gulmira; Petrovic, Sanja; Jagannathan, Rupa

2015-01-01

Radiotherapy treatment planning aims to deliver a sufficient radiation dose to cancerous tumour cells while sparing healthy organs in the tumour surrounding area. This is a trial and error process highly dependent on the medical staff's experience and knowledge. Case-Based Reasoning (CBR) is an artificial intelligence tool that uses past experiences to solve new problems. A CBR system has been developed to facilitate radiotherapy treatment planning for brain cancer. Given a new patient case the existing CBR system retrieves a similar case from an archive of successfully treated patient cases with the suggested treatment plan. The next step requires adaptation of the retrieved treatment plan to meet the specific demands of the new case. The CBR system was tested by medical physicists for the new patient cases. It was discovered that some of the retrieved cases were not suitable and could not be adapted for the new cases. This motivated us to revise the retrieval mechanism of the existing CBR system by adding a clustering stage that clusters cases based on their tumour positions. A number of well-known clustering methods were investigated and employed in the retrieval mechanism. Results using real world brain cancer patient cases have shown that the success rate of the new CBR retrieval is higher than that of the original system. (paper)

Engineering study for ISSTRS design concept

Energy Technology Data Exchange (ETDEWEB)

Hertzel, J.S.

1997-01-31

Los Alamos Technical Associates, Inc., is pleased to transmit the attached Conceptual Design Package for the Initial Single Shell Tank Retrieval System (ISSTRS), 90% Conceptual Design Review. The package includes the following: (1) ISSTRS Trade Studies: (a) Retrieval Facility Cooling Requirements; (b) Equipment Re-usability between Project W-320 and Tanks 241-C-103 and 241-C-1 05; (c) Sluice Line Options; and (d) Options for the Location of Tanks AX-103 and A-1 02 HVAC Equipment; (2) Drawings; (3) Risk Management Plan; (4) 0850 Interface Control Document; (5) Requirements Traceability Report; and (6) Project Design Specification.

Mixer pump test plan for double-shell tank AZ-101. Revision 1

Energy Technology Data Exchange (ETDEWEB)

Symons, G.A.

1996-02-01

Westinghouse Hanford Company has undertaken the task to develop and demonstrate a method of retrieval for double-shell tank waste. Mixer pumps were chosen as the planned method of retrieval for DSTs, based on engineering technology studies, past experience with hydraulic sluicing at the Hanford Site, and experience with mixer pumps at the Westinghouse Savannah River Site.

Mixer pump test plan for double-shell tank AZ-101. Revision 1

International Nuclear Information System (INIS)

Symons, G.A.

1996-02-01

Westinghouse Hanford Company has undertaken the task to develop and demonstrate a method of retrieval for double-shell tank waste. Mixer pumps were chosen as the planned method of retrieval for DSTs, based on engineering technology studies, past experience with hydraulic sluicing at the Hanford Site, and experience with mixer pumps at the Westinghouse Savannah River Site

Development of charged particle nuclear reaction data retrieval system on IntelligentPad

International Nuclear Information System (INIS)

Ohbayashi, Yosihide; Masui, Hiroshi; Aoyama, Shigeyoshi; Kato, Kiyoshi; Chiba, Masaki

1999-01-01

An newly designed database retrieval system of charged particle nuclear reaction database system is developed with IntelligentPad architecture. We designed the network-based (server-client) data retrieval system, and a client system constructs on Windows95, 98/NT with IntelligentPad. We set the future aim of our database system toward the 'effective' use of nuclear reaction data: I. 'Re-produce, Re-edit, Re-use', II. 'Circulation, Evolution', III. 'Knowledge discovery'. Thus, further developments are under way. (author)

Glucocorticoids interact with the hippocampal endocannabinoid system in impairing retrieval of contextual fear memory

Science.gov (United States)

Atsak, Piray; Hauer, Daniela; Campolongo, Patrizia; Schelling, Gustav; McGaugh, James L.; Roozendaal, Benno

2012-01-01

There is extensive evidence that glucocorticoid hormones impair the retrieval of memory of emotionally arousing experiences. Although it is known that glucocorticoid effects on memory retrieval impairment depend on rapid interactions with arousal-induced noradrenergic activity, the exact mechanism underlying this presumably nongenomically mediated glucocorticoid action remains to be elucidated. Here, we show that the hippocampal endocannabinoid system, a rapidly activated retrograde messenger system, is involved in mediating glucocorticoid effects on retrieval of contextual fear memory. Systemic administration of corticosterone (0.3–3 mg/kg) to male Sprague–Dawley rats 1 h before retention testing impaired the retrieval of contextual fear memory without impairing the retrieval of auditory fear memory or directly affecting the expression of freezing behavior. Importantly, a blockade of hippocampal CB1 receptors with AM251 prevented the impairing effect of corticosterone on retrieval of contextual fear memory, whereas the same impairing dose of corticosterone increased hippocampal levels of the endocannabinoid 2-arachidonoylglycerol. We also found that antagonism of hippocampal β-adrenoceptor activity with local infusions of propranolol blocked the memory retrieval impairment induced by the CB receptor agonist WIN55,212–2. Thus, these findings strongly suggest that the endocannabinoid system plays an intermediary role in regulating rapid glucocorticoid effects on noradrenergic activity in impairing memory retrieval of emotionally arousing experiences. PMID:22331883

An information retrieval system for research file data

Science.gov (United States)

Joan E. Lengel; John W. Koning

1978-01-01

Research file data have been successfully retrieved at the Forest Products Laboratory through a high-speed cross-referencing system involving the computer program FAMULUS as modified by the Madison Academic Computing Center at the University of Wisconsin. The method of data input, transfer to computer storage, system utilization, and effectiveness are discussed....

Optimal routing in an automated storage/retrieval system with dedicated storage

NARCIS (Netherlands)

Berg, van den J.P.; Gademann, A.J.R.M.

1999-01-01

We address the sequencing of requests in an automated storage/retrieval system with dedicated storage. We consider the block sequencing approach, where a set of storage and retrieval requests is given beforehand and no new requests come in during operation. The objective for this static problem is

Method of and System for Information Retrieval

DEFF Research Database (Denmark)

2015-01-01

This invention relates to a system for and a method (100) of searching a collection of digital information (150) comprising a number of digital documents (110), the method comprising receiving or obtaining (102) a search query, the query comprising a number of search terms, searching (103) an ind......, a method of and a system for information retrieval or searching is readily provided that enhances the searching quality (i.e. the number of relevant documents retrieved and such documents being ranked high) when (also) using queries containing many search terms.......This invention relates to a system for and a method (100) of searching a collection of digital information (150) comprising a number of digital documents (110), the method comprising receiving or obtaining (102) a search query, the query comprising a number of search terms, searching (103) an index...... (300) using the search terms thereby providing information (301) about which digital documents (110) of the collection of digital information (150) that contains a given search term and one or more search related metrics (302; 303; 304; 305; 306), ranking (105) at least a part of the search result...

Project W-211 Initial Tank Retrieval Systems (ITRS) Description of Operations for 241-AZ-102

Energy Technology Data Exchange (ETDEWEB)

BRIGGS, S.R.

2000-02-25

The primary purpose of the Initial Tank Retrieval Systems (ITRS) is to provide systems for retrieval of radioactive wastes stored in underground double-shell tanks (DSTs) for transfer to alternate storage, evaporation, pretreatment or treatment, while concurrently reducing risks associated with safety watch list and other DSTs. This Description of Operation (DOO) defines the control philosophy for the waste retrieval system for Tank 241-AZ-102 (AZ-102). This DOO provides a basis for the detailed design of the Project W-211 Retrieval Control System (RCS) for AZ-102 and also establishes test criteria for the RCS.

Project W-211 Initial Tank Retrieval Systems (ITRS) Description of Operations for 241-AZ-102

International Nuclear Information System (INIS)

BRIGGS, S.R.

2000-01-01

The primary purpose of the Initial Tank Retrieval Systems (ITRS) is to provide systems for retrieval of radioactive wastes stored in underground double-shell tanks (DSTs) for transfer to alternate storage, evaporation, pretreatment or treatment, while concurrently reducing risks associated with safety watch list and other DSTs. This Description of Operation (DOO) defines the control philosophy for the waste retrieval system for Tank 241-AZ-102 (AZ-102). This DOO provides a basis for the detailed design of the Project W-211 Retrieval Control System (RCS) for AZ-102 and also establishes test criteria for the RCS

System design description for portable 1,000 CFM exhauster Skids POR-007/Skid E and POR-008/Skid F

International Nuclear Information System (INIS)

Nelson, O.D.

1998-01-01

The primary purpose of the two 1,000 CFM Exhauster Skids, POR-007-SKID E and POR-008-SKID F, is to provide backup to the waste tank primary ventilation systems for tanks 241-C-106 and 241-AY-102, and the AY-102 annulus in the event of a failure during the sluicing of tank 241-C-106 and subsequent transfer of sluiced waste to 241-AY-102. This redundancy is required since both of the tank ventilation systems have been declared as Safety Class systems

Document Level Assessment of Document Retrieval Systems in a Pairwise System Evaluation

Science.gov (United States)

Rajagopal, Prabha; Ravana, Sri Devi

2017-01-01

Introduction: The use of averaged topic-level scores can result in the loss of valuable data and can cause misinterpretation of the effectiveness of system performance. This study aims to use the scores of each document to evaluate document retrieval systems in a pairwise system evaluation. Method: The chosen evaluation metrics are document-level…

Implementation and evaluation of a medical image management system with content-based retrieval support

International Nuclear Information System (INIS)

Carita, Edilson Carlos; Seraphim, Enzo; Honda, Marcelo Ossamu; Azevedo-Marques, Paulo Mazzoncini de

2008-01-01

Objective: the present paper describes the implementation and evaluation of a medical images management system with content-based retrieval support (PACS-CBIR) integrating modules focused on images acquisition, storage and distribution, and text retrieval by keyword and images retrieval by similarity. Materials and methods: internet-compatible technologies were utilized for the system implementation with free ware, and C ++ , PHP and Java languages on a Linux platform. There is a DICOM-compatible image management module and two query modules, one of them based on text and the other on similarity of image texture attributes. Results: results demonstrate an appropriate images management and storage, and that the images retrieval time, always < 15 sec, was found to be good by users. The evaluation of retrieval by similarity has demonstrated that the selected images extractor allowed the sorting of images according to anatomical areas. Conclusion: based on these results, one can conclude that the PACS-CBIR implementation is feasible. The system has demonstrated to be DICOM-compatible, and that it can be integrated with the local information system. The similar images retrieval functionality can be enhanced by the introduction of further descriptors. (author)

Stagnation, circulation, and erosion of granular materials through belt conveyor sluice gate

Science.gov (United States)

Pohlman, Nicholas; Moralda, Michael; Dunne, Ryan

2013-11-01

Control of flow rates in conversion reactors for discrete materials like biomass can be achieved in belt conveyors through a combination of belt speed, hopper size, and aperture opening. As material is extracted from the bottom of the storage hopper, other material cannot achieve plug flow and therefore is restricted from exiting through a sluice-gate type opening. The excess material moves vertically from the opening causing a pile up and recirculation back along the free surface of the hopper. Experimental results obtained through high speed imaging show the position of the stagnation point as well as the rate of circulation is dependent on the mass flow rate achieved and instantaneous fill level. The movement of material into the plug flow along the belt allows verification of deposition models on erodible beds rather than rigid surfaces with artificial roughness of glued particles. Similarly, the pile-up at the exit influences the efficiency of the transport affecting the narrow energy return on investment of biomass resources. The laboratory-scale behavior can therefore be translated into industrial performance metrics for increased operational efficiency. This work is supported by the NSF REU Site Operation E-Tank under award number 1156789.

Impact of sediments resuspension on metal solubilization and water quality during recurrent reservoir sluicing management

Energy Technology Data Exchange (ETDEWEB)

Frémion, Franck; Courtin-Nomade, Alexandra [Groupement de Recherche Eau Sol Environnement, Université de Limoges, 123 avenue Albert Thomas, 87060 Limoges Cedex (France); Bordas, François, E-mail: francois.bordas@unilim.fr [Groupement de Recherche Eau Sol Environnement, Université de Limoges, 123 avenue Albert Thomas, 87060 Limoges Cedex (France); Lenain, Jean-François [Groupement de Recherche Eau Sol Environnement, Université de Limoges, 123 avenue Albert Thomas, 87060 Limoges Cedex (France); Jugé, Philippe [CETU – ELMIS Ingénieries, Université François Rabelais, , 60 Rue du Plat d' Étain, 37000 Tours (France); Kestens, Tim [EDF – DPIH, Unité de Production Centre, 19 bis avenue de la Révolution, BP 406, 87012 Limoges Cedex (France); Mourier, Brice [Groupement de Recherche Eau Sol Environnement, Université de Limoges, 123 avenue Albert Thomas, 87060 Limoges Cedex (France)

2016-08-15

In dam contexts, sluicing operations can be performed to reestablish sediments continuity, as proposed by the EU Water Framework Directive, as well as to preserve the reservoirs' water storage capacity. Such management permits the rapid release of high quantities of reservoir sediments through the opening of dam bottom valves. This work aims to study the impact of such operation on the evolution of environmental physicochemical conditions notably changes in dissolved metallic elements concentrations (Al, As, Cd, Cr, Cu, Fe, Mn, Ni, Pb, Zn) through field and laboratory investigations. Results were interpreted in terms of concentrations and fluxes, and compared with data collected on an annual basis regarding both suspended matter and metallic elements. The release of high quantities of sediments (4,500 tons dry weight in 24 h), with concentrations representing up to 300 times the inter-annual mean suspended sediments discharge, significantly modified water parameters, notably solid/liquid (S/L) ratio, pH and redox conditions. Despite the fact that they are mainly trapped in stable phases, a clear increase of the solubilized metals content was measured, representing up to 60 times the maximum values of current exploitation. This solubilization is related to desorption phenomena from sediments through changes in chemical equilibriums as highlighted by laboratory characterizations and experiments. These chemical modifications are mainly attributed to S/L ratio variations. Indeed, the low S/L ratios (≤ 1.3 g·L{sup −1}) measured in situ are typically the ones for which metals solubilization is the highest, as shown by laboratory experiments. Additional thermodynamic modeling highlighted that the decrease in pH measured during the operation favors the release of the free forms of metallic elements (Al and Cu), and decreases the OM complexation influence. These changes, either in term of physical conditions or speciation, increasing metals long term

Final Report - Spent Nuclear Fuel Retrieval System Manipulator System Cold Validation Testing

International Nuclear Information System (INIS)

D.R. Jackson; G.R. Kiebel

1999-01-01

Manipulator system cold validation testing (CVT) was performed in support of the Fuel Retrieval System (FRS) Sub-Project, a subtask of the Spent Nuclear Fuel Project at the Hanford Site in Richland, Washington. The FRS will be used to retrieve and repackage K-Basin Spent Nuclear Fuel (SNF) currently stored in old K-Plant storage basins. The FRS is required to retrieve full fuel canisters from the basin; clean the fuel elements inside the canister to remove excessive uranium corrosion products (or sludge); remove the contents from the canisters; and sort the resulting debris, scrap, and fuel for repackaging. The fuel elements and scrap will be collected in fuel storage and scrap baskets in preparation for loading into a multi canister overpack (MCO), while the debris is loaded into a debris bin and disposed of as solid waste. The FRS is composed of three major subsystems. The Manipulator Subsystem provides remote handling of fuel, scrap, and debris; the In-Pool Equipment subsystem performs cleaning of fuel and provides a work surface for handling materials; and the Remote Viewing Subsystem provides for remote viewing of the work area by operators. There are two complete and identical FRS systems, one to be installed in the K-West basin and one to be installed in the K-East basin. Another partial system will be installed in a cold test facility to provide for operator training

Final Report - Spent Nuclear Fuel Retrieval System Manipulator System Cold Validation Testing

Energy Technology Data Exchange (ETDEWEB)

D.R. Jackson; G.R. Kiebel

1999-08-24

Manipulator system cold validation testing (CVT) was performed in support of the Fuel Retrieval System (FRS) Sub-Project, a subtask of the Spent Nuclear Fuel Project at the Hanford Site in Richland, Washington. The FRS will be used to retrieve and repackage K-Basin Spent Nuclear Fuel (SNF) currently stored in old K-Plant storage basins. The FRS is required to retrieve full fuel canisters from the basin; clean the fuel elements inside the canister to remove excessive uranium corrosion products (or sludge); remove the contents from the canisters; and sort the resulting debris, scrap, and fuel for repackaging. The fuel elements and scrap will be collected in fuel storage and scrap baskets in preparation for loading into a multi canister overpack (MCO), while the debris is loaded into a debris bin and disposed of as solid waste. The FRS is composed of three major subsystems. The Manipulator Subsystem provides remote handling of fuel, scrap, and debris; the In-Pool Equipment subsystem performs cleaning of fuel and provides a work surface for handling materials; and the Remote Viewing Subsystem provides for remote viewing of the work area by operators. There are two complete and identical FRS systems, one to be installed in the K-West basin and one to be installed in the K-East basin. Another partial system will be installed in a cold test facility to provide for operator training.

System design for retrieval of solidified high-level wastes at Hanford

International Nuclear Information System (INIS)

Wallskog, H.A.

1977-01-01

A Waste Retrieval System has been conceptually designed as a step in the process toward the demonstration of the capability to retrieve the projected 36,000,000 gallons of radioactive salt cake and sludge wastes from underground storage tanks at Hanford. This functionally complete, totally remotely operable system consists of a large mobile platform containing all of the tools and equipment necessary to recover, remove and package the wastes for transfer to an onsite processing facility

MARS: Microarray analysis, retrieval, and storage system

Directory of Open Access Journals (Sweden)

Scheideler Marcel

2005-04-01

Full Text Available Abstract Background Microarray analysis has become a widely used technique for the study of gene-expression patterns on a genomic scale. As more and more laboratories are adopting microarray technology, there is a need for powerful and easy to use microarray databases facilitating array fabrication, labeling, hybridization, and data analysis. The wealth of data generated by this high throughput approach renders adequate database and analysis tools crucial for the pursuit of insights into the transcriptomic behavior of cells. Results MARS (Microarray Analysis and Retrieval System provides a comprehensive MIAME supportive suite for storing, retrieving, and analyzing multi color microarray data. The system comprises a laboratory information management system (LIMS, a quality control management, as well as a sophisticated user management system. MARS is fully integrated into an analytical pipeline of microarray image analysis, normalization, gene expression clustering, and mapping of gene expression data onto biological pathways. The incorporation of ontologies and the use of MAGE-ML enables an export of studies stored in MARS to public repositories and other databases accepting these documents. Conclusion We have developed an integrated system tailored to serve the specific needs of microarray based research projects using a unique fusion of Web based and standalone applications connected to the latest J2EE application server technology. The presented system is freely available for academic and non-profit institutions. More information can be found at http://genome.tugraz.at.

Tank waste remediation system retrieval and disposal mission infrastructure plan

International Nuclear Information System (INIS)

Root, R.W.

1998-01-01

This system plan presents the objectives, organization, and management and technical approaches for the Infrastructure Program. This Infrastructure Plan focuses on the Tank Waste Remediation System (TWRS) Project's Retrieval and Disposal Mission

Monitored Retrievable Storage System Requirements Document

International Nuclear Information System (INIS)

1994-03-01

This Monitored Retrievable Storage System Requirements Document (MRS-SRD) describes the functions to be performed and technical requirements for a Monitored Retrievable Storage (MRS) facility subelement and the On-Site Transfer and Storage (OSTS) subelement. The MRS facility subelement provides for temporary storage, at a Civilian Radioactive Waste Management System (CRWMS) operated site, of spent nuclear fuel (SNF) contained in an NRC-approved Multi-Purpose Canister (MPC) storage mode, or other NRC-approved storage modes. The OSTS subelement provides for transfer and storage, at Purchaser sites, of spent nuclear fuel (SNF) contained in MPCs. Both the MRS facility subelement and the OSTS subelement are in support of the CRWMS. The purpose of the MRS-SRD is to define the top-level requirements for the development of the MRS facility and the OSTS. These requirements include design, operation, and decommissioning requirements to the extent they impact on the physical development of the MRS facility and the OSTS. The document also presents an overall description of the MRS facility and the OSTS, their functions (derived by extending the functional analysis documented by the Physical System Requirements (PSR) Store Waste Document), their segments, and the requirements allocated to the segments. In addition, the top-level interface requirements of the MRS facility and the OSTS are included. As such, the MRS-SRD provides the technical baseline for the MRS Safety Analysis Report (SAR) design and the OSTS Safety Analysis Report design

Personalized Mobile Information Retrieval System

Directory of Open Access Journals (Sweden)

Okkyung Choi

2012-04-01

Full Text Available Building a global Network Relations with the internet has made huge changes in personal information system and even comments left on a webpage of SNS(Social Network Services are appreciated as important elements that would provide valuable information for someone. Social Network is a relation between individuals or groups, represented in a graph model, which converts the concept of psychological and social relations into a logical structure by using node and link. But, most of the current personalized systems on the basis of Social Network are built and constructed mainly in the PC environment, and the systems are neither designed nor implemented in mobile environment. Hence, the objective of this study is to propose methods of providing Personalized Mobile Information Retrieval System using NFC (Near Field Communication Smartphone, which will be then used for Smartphone users. Besides, this study aims to verify its efficiency through a comparative analysis of existing studies.

Designing and Implementing a Cross-Language Information Retrieval System Using Linguistic Corpora

Directory of Open Access Journals (Sweden)

Amin Nezarat

2012-03-01

Full Text Available Information retrieval (IR is a crucial area of natural language processing (NLP and can be defined as finding documents whose content is relevant to the query need of a user. Cross-language information retrieval (CLIR refers to a kind of information retrieval in which the language of the query and that of searched document are different. In fact, it is a retrieval process where the user presents queries in one language to retrieve documents in another language. This paper tried to construct a bilingual lexicon of parallel chunks of English and Persian from two very large monolingual corpora an English-Persian parallel corpus which could be directly applied to cross-language information retrieval tasks. For this purpose, a statistical measure known as Association Score (AS was used to compute the association value between every two corresponding chunks in the corpus using a couple of complicated algorithms. Once the CLIR system was developed using this bilingual lexicon, an experiment was performed on a set of one hundred English and Persian phrases and collocations to see to what extend this system was effective in assisting the users find the most relevant and suitable equivalents of their queries in either language.

Retrievable surface storage facility conceptual system design description

Energy Technology Data Exchange (ETDEWEB)

1977-03-01

The studies evaluated several potentially attractive methods for processing and retrievably storing high-level radioactive waste after delivery to the Federal repository. These studies indicated that several systems could be engineered to safely store the waste, but that the simplest and most attractive concept from a technical standpoint would be to store the waste in a sealed stainless steel canister enclosed in a 2 in. thick carbon steel cask which in turn would be inserted into a reinforced concrete gamma-neutron shield, which would also provide the necessary air-cooling through an air annulus between the cask and the shield. This concept best satisfies the requirements for safety, long-term exposure to natural phenomena, low capital and operating costs, retrievability, amenability to incremental development, and acceptably small environmental impact. This document assumes that the reference site would be on ERDA's Hanford reservation. This document is a Conceptual System Design Description of the facilities which could satisfy all of the functional requirements within the established basic design criteria. The Retrievable Surface Storage Facility (RSSF) is planned with the capacity to process and store the waste received in either a calcine or glass/ceramic form. The RSSF planning is based on a modular development program in which the modular increments are constructed at rates matching projected waste receipts.

Retrievable surface storage facility conceptual system design description

International Nuclear Information System (INIS)

1977-03-01

The studies evaluated several potentially attractive methods for processing and retrievably storing high-level radioactive waste after delivery to the Federal repository. These studies indicated that several systems could be engineered to safely store the waste, but that the simplest and most attractive concept from a technical standpoint would be to store the waste in a sealed stainless steel canister enclosed in a 2 in. thick carbon steel cask which in turn would be inserted into a reinforced concrete gamma-neutron shield, which would also provide the necessary air-cooling through an air annulus between the cask and the shield. This concept best satisfies the requirements for safety, long-term exposure to natural phenomena, low capital and operating costs, retrievability, amenability to incremental development, and acceptably small environmental impact. This document assumes that the reference site would be on ERDA's Hanford reservation. This document is a Conceptual System Design Description of the facilities which could satisfy all of the functional requirements within the established basic design criteria. The Retrievable Surface Storage Facility (RSSF) is planned with the capacity to process and store the waste received in either a calcine or glass/ceramic form. The RSSF planning is based on a modular development program in which the modular increments are constructed at rates matching projected waste receipts

A high accuracy land use/cover retrieval system

Directory of Open Access Journals (Sweden)

Alaa Hefnawy

2012-03-01

Full Text Available The effects of spatial resolution on the accuracy of mapping land use/cover types have received increasing attention as a large number of multi-scale earth observation data become available. Although many methods of semi automated image classification of remotely sensed data have been established for improving the accuracy of land use/cover classification during the past 40 years, most of them were employed in single-resolution image classification, which led to unsatisfactory results. In this paper, we propose a multi-resolution fast adaptive content-based retrieval system of satellite images. Through our proposed system, we apply a Super Resolution technique for the Landsat-TM images to have a high resolution dataset. The human–computer interactive system is based on modified radial basis function for retrieval of satellite database images. We apply the backpropagation supervised artificial neural network classifier for both the multi and single resolution datasets. The results show significant improved land use/cover classification accuracy for the multi-resolution approach compared with those from single-resolution approach.

Proposed computerized cross-index system for storage and retrieval ...

African Journals Online (AJOL)

Card index systems are normally not very efficient when used for cross-indexing purposes and information retrieval, useful information frequently being lost because of poor indexing and little or no cross-referencing. Large card index systems are often compiled by research workers but these potentially useful stores of ...

Climate Change Impact Assessment of Dike Safety and Flood Risk in the Vidaa River System

DEFF Research Database (Denmark)

Madsen, H.; Sunyer Pinya, Maria Antonia; Larsen, J.

2013-01-01

The impact of climate change on the flood risk and dike safety in the Vidaa River system, a cross-border catchment located in the southern part of Jutland, Denmark and northern Germany, is analysed. The river discharges to the Wadden Sea through a tidal sluice, and extreme water level conditions...... in the river system occur in periods of high sea water levels where the sluice is closed and increased catchment run-off take place. Climate model data from the ENSEMBLES data archive are used to assess the changes in climate variables and the resulting effect on catchment run-off. Extreme catchment run......-off is expected to increase about 8 % in 2050 and 14 % in 2100. The changes in sea water level is assessed considering climate projections of mean sea level rise, isostatic changes, and changes in storm surge statistics. At the Vidaa sluice a mean sea level rise of 0.15–0.39 m in 2050 and 0.41–1.11 m in 2010...

Multiple products management system with sensors array in automated storage and retrieval systems

Science.gov (United States)

Vongbunyong, Supachai; Roengritronnachai, Perawat; Kongsanit, Savanut; Chanok-owat, Chawisa; Polchankajorn, Pongsakorn

2018-01-01

Automated Storage and Retrieval Systems (AS/RS) have now been widely used in a number of industries due to its capability to automatically manage the storage of products in effective ways. One of the key features of AS/RS is that each rack is not assigned for a specific product resulting in the benefit of space utilization and logistics related issues. In this research, sensor arrays are equipped at each rack in order to enhance this feature. As a result, various products can be identified and mixed in each rack, so that the space utilization efficiency can be increased. To prove the concept, a prototype system consisting of a Cartesian robot that manages the storage and retrieval of products with 9 variations based on size and color. The concept of Cyber-Physical System and self-awareness of the system are also implemented in this concept prototype.

System Description for Tank 241-AZ-101 Waste Retrieval Data Acquisition System

International Nuclear Information System (INIS)

ROMERO, S.G.

2000-01-01

The proposed activity provides the description of the Data Acquisition System for Tank 241-AZ-101. This description is documented in HNF-5572, Tank 241-AZ-101 Waste Retrieval Data Acquisition System (DAS). This activity supports the planned mixer pump tests for Tank 241-AZ-101. Tank 241-AZ-101 has been selected for the first full-scale demonstration of a mixer pump system. The tank currently holds over 960,000 gallons of neutralized current acid waste, including approximately 12.7 inches of settling solids (sludge) at the bottom of the tank. As described in Addendum 4 of the FSAR (LMHC 2000a), two 300 HP mixer pumps with associated measurement and monitoring equipment have been installed in Tank 241-AZ-101. The purpose of the Tank 241-AZ-101 retrieval system Data Acquisition System (DAS) is to provide monitoring and data acquisition of key parameters in order to confirm the effectiveness of the mixer pumps utilized for suspending solids in the tank. The suspension of solids in Tank 241-AZ-101 is necessary for pretreatment of the neutralized current acid waste and eventual disposal as glass via the Hanford Waste Vitrification Plant. HNF-5572 provides a basic description of the Tank 241-AZ-101 retrieval system DAS, including the field instrumentation and application software. The DAS is provided to fulfill requirements for data collection and monitoring. This document is not an operations procedure or is it intended to describe the mixing operation. This USQ screening provides evaluation of HNF-5572 (Revision 1) including the changes as documented on ECN 654001. The changes include (1) add information on historical trending and data backup, (2) modify DAS I/O list in Appendix E to reflect actual conditions in the field, and (3) delete IP address in Appendix F per Lockheed Martin Services, Inc. request

Monitoring User-System Performance in Interactive Retrieval Tasks

NARCIS (Netherlands)

Boldareva, L.; de Vries, A.P.; Hiemstra, Djoerd

Monitoring user-system performance in interactive search is a challenging task. Traditional measures of retrieval evaluation, based on recall and precision, are not of any use in real time, for they require a priori knowledge of relevant documents. This paper shows how a Shannon entropy-based

An integrated information retrieval and document management system

Science.gov (United States)

Coles, L. Stephen; Alvarez, J. Fernando; Chen, James; Chen, William; Cheung, Lai-Mei; Clancy, Susan; Wong, Alexis

1993-01-01

This paper describes the requirements and prototype development for an intelligent document management and information retrieval system that will be capable of handling millions of pages of text or other data. Technologies for scanning, Optical Character Recognition (OCR), magneto-optical storage, and multiplatform retrieval using a Standard Query Language (SQL) will be discussed. The semantic ambiguity inherent in the English language is somewhat compensated-for through the use of coefficients or weighting factors for partial synonyms. Such coefficients are used both for defining structured query trees for routine queries and for establishing long-term interest profiles that can be used on a regular basis to alert individual users to the presence of relevant documents that may have just arrived from an external source, such as a news wire service. Although this attempt at evidential reasoning is limited in comparison with the latest developments in AI Expert Systems technology, it has the advantage of being commercially available.

Development of EDFSRS: evaluated data files storage and retrieval system

International Nuclear Information System (INIS)

Hasegawa, Akira

1985-07-01

EDFSRS: Evaluated Data Files Storage and Retrieval System has been developed, which is a complete service system for the evaluated nuclear data files compiled in the major three formats: ENDF/B, UKNDL and KEDAK. This system intends to give efficient loading and maintenance of evaluated nuclear data files to the data base administrators and efficient retrievals to their users not only with the easiness but with the best confidence. It can give users all of the information available in these major three formats. The system consists of more than fifteen independent programs and some 150 Mega byte data files and index files (data-base) of the loaded data. In addition it is designed to be operated in the on-line TSS (Time Sharing System) mode, so that users can get any information from their desk top terminals. This report is prepared as a reference manual of the EDFSRS. (author)

Simulation study of an automated storage/retrieval system

NARCIS (Netherlands)

Berg, van den J.P.; Gademann, A.J.R.M.

2000-01-01

In this paper we present a simulation study of an automated storage/retrieval system and examine a wide variety of control policies. We compare several storage location assignment policies. For the class-based storage policy, we apply a recent algorithm that enables us to evaluate the trade-off

Status report on SIRS: sorption information retrieval system

International Nuclear Information System (INIS)

Hostetler, D.D.; Serne, R.J.; Baldwin, A.J.; Petrie, G.M.

1980-11-01

Two major uses were identified for the Sorption Information Retrieval System: (1) to aid geochemists in the elucidation of sorption mechanisms; and (2) to aid safety assessment modelers in selection of Kds for any given scenerio. Other benefits such as providing an auditable vehicle for the Kd selection were also discussed

Innovative systems for mixed waste retrieval and/or treatment in confined spaces

International Nuclear Information System (INIS)

Fekete, L.J.; Ghusn, A.E.

1993-03-01

Fernald established operations in 1951 and produced uranium and other metals for use at other DOE facilities. A part of the sitewide remediation effort is the removal, treatment, and disposal of the K-65 wastes from Silos 1 and 2. These silos contain radium-bearing residues from the processing of pitchblende ore. An Engineering Evaluation/Cost Analysis was prepared to evaluate the removal action alternatives using the preliminary characterization data and select a preferred alternative. The selected alternative consisted of covering the K-65 residues and the silo dome. The remediation of the K-65 wastes consists of the retrieval and treatment of the wastes prior to final disposal, which has not yet been determined. Treatment will be performed in a new facility to be built adjacent to the silos. The wastes must be retrieved from silos in an efficient and reliable way and delivered to the treatment facility. The first challenge of covering the wastes with bentonite has been successfully met. The second phase of retrieving the wastes from the silos is not due for a few years. However, conceptual design and configuration of the retrieval system have been developed as part of the Conceptual Design Report. The system is based on the utilization of hydraulic mining techniques, and is based on similar successful applications. This report describes the emplacement of the bentonite grant and the design for the slurry retrieval system

Dynamics, control and sensor issues pertinent to robotic hands for the EVA retriever system

Science.gov (United States)

Mclauchlan, Robert A.

1987-01-01

Basic dynamics, sensor, control, and related artificial intelligence issues pertinent to smart robotic hands for the Extra Vehicular Activity (EVA) Retriever system are summarized and discussed. These smart hands are to be used as end effectors on arms attached to manned maneuvering units (MMU). The Retriever robotic systems comprised of MMU, arm and smart hands, are being developed to aid crewmen in the performance of routine EVA tasks including tool and object retrieval. The ultimate goal is to enhance the effectiveness of EVA crewmen.

Decontamination system study for the Tank Waste Retrieval System

International Nuclear Information System (INIS)

Reutzel, T.; Manhardt, J.

1994-05-01

This report summarizes the findings of the Idaho National Engineering Laboratory's decontamination study in support of the Tank Waste Retrieval System (TWRS) development program. Problems associated with waste stored in existing single shell tanks are discussed as well as the justification for the TWRS program. The TWRS requires a decontamination system. The subsystems of the TWRS are discussed, and a list of assumptions pertinent to the TWRS decontamination system were developed. This information was used to develop the functional and operational requirements of the TWRS decontamination system. The requirements were combined with a comprehensive review of currently available decontamination techniques to produced a set of evaluation criteria. The cleaning technologies and techniques were evaluated, and the CO 2 blasting decontamination technique was chosen as the best technology for the TWRS

Systems Engineering Implementation Plan for Single-Shell Tanks (SST) Retrieval Projects

International Nuclear Information System (INIS)

LEONARD, M.W.; HOFFERBER, G.A.

2000-01-01

This document communicates the planned implementation of the Systems Engineering processes and products for the SST retrieval projects as defined in the Systems Engineering Management Plan for the Tank Farm Contractor

Systems Engineering Implementation Plan for Single Shell Tanks (SST) Retrieval Projects

Energy Technology Data Exchange (ETDEWEB)

LEONARD, M.W.; HOFFERBER, G.A.

2000-11-30

This document communicates the planned implementation of the Systems Engineering processes and products for the SST retrieval projects as defined in the Systems Engineering Management Plan for the Tank Farm Contractor.

Mission analysis report for the Hanford Tanks Initiative

International Nuclear Information System (INIS)

Schaus, P.S.

1997-01-01

This mission analysis report for the Hanford Tanks Initiative (HTI) supports the Hanford Site's Single-Shell Tank (SST) Waste Retrieval Program in its commitment to remove waste from the SSTs for treatment and final closure of the tanks. The results of the HTI will support the US Department of Energy's (DOE) privatization of retrieval efforts. This report addresses the HTI problem statement: Alternative technologies to past practice sluicing (PPS) have not yet been demonstrated to remove the hard heel from a sluiced tank or to remove waste from a leaking SST. Nor have performance-based criteria for cleanout and closure been demonstrated to the degree necessary to validate them as technically and economically achievable. This report also defines the mission statement and mission boundaries; the known interfaces, both programmatic and project; the mission level requirements; the test and evaluation methodology; and measures of success

User interfaces of information retrieval systems and user friendliness

Directory of Open Access Journals (Sweden)

Polona Vilar

2008-01-01

Full Text Available The paper deals with the characteristics of user interfaces of information retrieval systems with the emphasis on design and evaluation. It presents users’ information retrieval tasks and the functions which are offered through interfaces. Design rules, guidelines and standards are presented, as well as criteria and methods for evaluation. Special emphasis is placed on the concept of user friendliness as one of the most important characteristic of the user interfaces. Various definitions of user friendliness are presented and their elements are also discussed. In the end, the paper shows how user interfaces should be designed, taken into consideration all these criteria.

The development of brain systems associated with successful memory retrieval of scenes.

Science.gov (United States)

Ofen, Noa; Chai, Xiaoqian J; Schuil, Karen D I; Whitfield-Gabrieli, Susan; Gabrieli, John D E

2012-07-18

Neuroanatomical and psychological evidence suggests prolonged maturation of declarative memory systems in the human brain from childhood into young adulthood. Here, we examine functional brain development during successful memory retrieval of scenes in children, adolescents, and young adults ages 8-21 via functional magnetic resonance imaging. Recognition memory improved with age, specifically for accurate identification of studied scenes (hits). Successful retrieval (correct old-new decisions for studied vs unstudied scenes) was associated with activations in frontal, parietal, and medial temporal lobe (MTL) regions. Activations associated with successful retrieval increased with age in left parietal cortex (BA7), bilateral prefrontal, and bilateral caudate regions. In contrast, activations associated with successful retrieval did not change with age in the MTL. Psychophysiological interaction analysis revealed that there were, however, age-relate changes in differential connectivity for successful retrieval between MTL and prefrontal regions. These results suggest that neocortical regions related to attentional or strategic control show the greatest developmental changes for memory retrieval of scenes. Furthermore, these results suggest that functional interactions between MTL and prefrontal regions during memory retrieval also develop into young adulthood. The developmental increase of memory-related activations in frontal and parietal regions for retrieval of scenes and the absence of such an increase in MTL regions parallels what has been observed for memory encoding of scenes.

A Fuzzy Semantic Information Retrieval System for Transactional Applications

OpenAIRE

A O Ajayi; H A Soriyan; G A Aderounmu

2009-01-01

In this paper, we present an information retrieval system based on the concept of fuzzy logic to relate vague and uncertain objects with un-sharp boundaries. The simple but comprehensive user interface of the system permits the entering of uncertain specifications in query forms. The system was modelled and simulated in a Matlab environment; its implementation was carried out using Borland C++ Builder. The result of the performance measure of the system using precision and recall rates is enc...

Performance Assessment of the Waste Dislodging Conveyance System During the Gunite And Associated Tanks Remediation Project

International Nuclear Information System (INIS)

Lloyd, P.D.

2001-01-01

The Waste Dislodging and Conveyance System (WD and CS) and other components of the Tank Waste Retrieval System (TWRS) were developed to address the need for removal of hazardous wastes from underground storage tanks (USTs) in which radiation levels and access limitations make traditional waste retrieval methods impractical. Specifically, these systems were developed for cleanup of the Gunite and Associated Tanks (GAAT) Operable Unit (OU) at the Oak Ridge National Laboratory (ORNL). The WD and CS is comprised of a number of different components. The three primary hardware subsystems are the Hose Management System (HMS), the Confined Sluicing End-Effector (CSEE), and the Flow Control Equipment and Containment Box (FCE/CB). In addition, a Decontamination Spray Ring (DSR) and a control system were developed for the system. The WD and CS is not a stand-alone system; rather, it is designed for deployment with either a long-reach manipulator like the Modified Light Duty Utility Arm (MLDUA) or a remotely operated vehicle system such as the Houdinitrademark. The HMS was designed to act as a pipeline for the transfer of dislodged waste; as a hose-positioning and tether-management system; and as a housing for process equipment such as the water-powered jet pump that provides the necessary suction to vacuum slurried waste from the UST. The HMS was designed to facilitate positioning of an end-effector at any point within the 25-ft- or 50-ft-diameter USTs in the GAAT OU

Performance benefits of telerobotics and teleoperation - enhancements for an arm-based tank waste retrieval system

International Nuclear Information System (INIS)

Horschel, D.S.; Gibbons, P.W.; Draper, J.V.

1995-06-01

This report evaluates telerobotic and teleoperational arm-based retrieval systems that require advanced robotic controls. These systems will be deployed in waste retrieval activities in Hanford's Single Shell Tanks (SSTs). The report assumes that arm-based, retrieval systems will combine a teleoperational arm and control system enhanced by a number of advanced and telerobotic controls. The report describes many possible enhancements, spanning the full range of the control spectrum with the potential for technical maturation. The enhancements considered present a variety of choices and factors including: the enhancements to be included in the actual control system, safety, detailed task analyses, human factors, cost-benefit ratios, and availability and maturity of technology. Because the actual system will be designed by an offsite vendor, the procurement specifications must have the flexibility to allow bidders to propose a broad range of ideas, yet build in enough restrictions to filter out infeasible and undesirable approaches. At the same time they must allow selection of a technically promising proposal. Based on a preliminary analysis of the waste retrieval task, and considering factors such as operator limitations and the current state of robotics technology, the authors recommend a set of enhancements that will (1) allow the system to complete its waste retrieval mission, and (2) enable future upgrades in response to changing mission needs and technological advances

Performance benefits of telerobotics and teleoperation - enhancements for an arm-based tank waste retrieval system

Energy Technology Data Exchange (ETDEWEB)

Horschel, D.S. [Sandia National Labs., Albuquerque, NM (United States); Gibbons, P.W. [Westinghouse Hanford Co., Richland, WA (United States); Draper, J.V. [Oak Ridge National Lab., TN (United States)] [and others

1995-06-01

This report evaluates telerobotic and teleoperational arm-based retrieval systems that require advanced robotic controls. These systems will be deployed in waste retrieval activities in Hanford`s Single Shell Tanks (SSTs). The report assumes that arm-based, retrieval systems will combine a teleoperational arm and control system enhanced by a number of advanced and telerobotic controls. The report describes many possible enhancements, spanning the full range of the control spectrum with the potential for technical maturation. The enhancements considered present a variety of choices and factors including: the enhancements to be included in the actual control system, safety, detailed task analyses, human factors, cost-benefit ratios, and availability and maturity of technology. Because the actual system will be designed by an offsite vendor, the procurement specifications must have the flexibility to allow bidders to propose a broad range of ideas, yet build in enough restrictions to filter out infeasible and undesirable approaches. At the same time they must allow selection of a technically promising proposal. Based on a preliminary analysis of the waste retrieval task, and considering factors such as operator limitations and the current state of robotics technology, the authors recommend a set of enhancements that will (1) allow the system to complete its waste retrieval mission, and (2) enable future upgrades in response to changing mission needs and technological advances.

Simulation analysis of control strategies for a tank waste retrieval manipulator system

International Nuclear Information System (INIS)

Schryver, J.C.; Draper, J.V.

1995-01-01

A network simulation model was developed for the Tank Waste Retrieval Manipulator System, incorporating two distinct levels of control: teleoperation and supervisory control. The model included six error modes, an attentional resource model, and a battery of timing variables. A survey questionnaire administered to subject matter experts provided data for estimating timing distributions for level of control-critical tasks. Simulation studies were performed to evaluate system behavior as a function of control level and error modes. The results provide important insights for development of waste retrieval manipulators

Natural language retrieval in nuclear safety information system

International Nuclear Information System (INIS)

Komata, Masaoki; Oosawa, Yasuo; Ujita, Hiroshi

1983-01-01

A natural language retrieval program NATLANG is developed to assist in the retrieval of information from event-and-cause descriptions in Licensee Event Reports (LER). The characteristics of NATLANG are (1) the use of base forms of words to retrieve related forms altered by the addition of prefixes or suffixes or changes in inflection, (2) direct access and short time retrieval with an alphabet pointer, (3) effective determination of the items and entries for a Hitachi event classification in a two step retrieval scheme, and (4) Japanese character output with the PL-1 language. NATLANG output reduces the effort needed to re-classify licensee events in the Hitachi event classification. (author)

A novel biomedical image indexing and retrieval system via deep preference learning.

Science.gov (United States)

Pang, Shuchao; Orgun, Mehmet A; Yu, Zhezhou

2018-05-01

The traditional biomedical image retrieval methods as well as content-based image retrieval (CBIR) methods originally designed for non-biomedical images either only consider using pixel and low-level features to describe an image or use deep features to describe images but still leave a lot of room for improving both accuracy and efficiency. In this work, we propose a new approach, which exploits deep learning technology to extract the high-level and compact features from biomedical images. The deep feature extraction process leverages multiple hidden layers to capture substantial feature structures of high-resolution images and represent them at different levels of abstraction, leading to an improved performance for indexing and retrieval of biomedical images. We exploit the current popular and multi-layered deep neural networks, namely, stacked denoising autoencoders (SDAE) and convolutional neural networks (CNN) to represent the discriminative features of biomedical images by transferring the feature representations and parameters of pre-trained deep neural networks from another domain. Moreover, in order to index all the images for finding the similarly referenced images, we also introduce preference learning technology to train and learn a kind of a preference model for the query image, which can output the similarity ranking list of images from a biomedical image database. To the best of our knowledge, this paper introduces preference learning technology for the first time into biomedical image retrieval. We evaluate the performance of two powerful algorithms based on our proposed system and compare them with those of popular biomedical image indexing approaches and existing regular image retrieval methods with detailed experiments over several well-known public biomedical image databases. Based on different criteria for the evaluation of retrieval performance, experimental results demonstrate that our proposed algorithms outperform the state

Proximal balloon deflation technique: a novel method to retrieve retained or entrapped equipment from the coronary system.

Science.gov (United States)

Ashikaga, Takashi; Inagaki, Hiroshi; Satoh, Yasuhiro; Isobe, Mitsuaki

2012-01-01

Complications of retained or entrapped equipment in the coronary system are still encountered during angioplasty procedures. Although these complications are rare, it is extremely difficult to retrieve such equipments. We report on two cases that a retained IVUS catheter or an entrapped filter wire were retrieved from the coronary system using more simplified technique that does not involve in the usage of snare or any other retrieval tool. After placing an additional guidewire and balloon alongside an equipment, it was easily retrieved from the coronary system just after the proximal balloon deflation. Copyright © 2012. Published by Elsevier Inc.

Utah Text Retrieval Project

Energy Technology Data Exchange (ETDEWEB)

Hollaar, L A

1983-10-01

The Utah Text Retrieval project seeks well-engineered solutions to the implementation of large, inexpensive, rapid text information retrieval systems. The project has three major components. Perhaps the best known is the work on the specialized processors, particularly search engines, necessary to achieve the desired performance and cost. The other two concern the user interface to the system and the system's internal structure. The work on user interface development is not only concentrating on the syntax and semantics of the query language, but also on the overall environment the system presents to the user. Environmental enhancements include convenient ways to browse through retrieved documents, access to other information retrieval systems through gateways supporting a common command interface, and interfaces to word processing systems. The system's internal structure is based on a high-level data communications protocol linking the user interface, index processor, search processor, and other system modules. This allows them to be easily distributed in a multi- or specialized-processor configuration. It also allows new modules, such as a knowledge-based query reformulator, to be added. 15 references.

Systems approach for design control at Monitored Retrievable Storage Project

International Nuclear Information System (INIS)

Kumar, P.N.; Williams, J.R.

1994-01-01

This paper describes the systems approach in establishing design control for the Monitored Retrievable Storage Project design development. Key elements in design control are enumerated and systems engineering aspects are detailed. Application of lessons learned from the Yucca Mountain Project experience is addressed. An integrated approach combining quality assurance and systems engineering requirements is suggested to practice effective design control

DARE: Unesco Computerized Data Retrieval System for Documentation in the Social and Human Sciences (Including an Analysis of the Present System).

Science.gov (United States)

Vasarhelyi, Paul

The new data retrieval system for the social sciences which has recently been installed in the UNESCO Secretariat in Paris is described in this comprehensive report. The computerized system is designed to facilitate the existing storage systems in the circulation of information, data retrieval, and indexing services. Basically, this report…

Operational test report - Project W-320 cathodic protection systems

International Nuclear Information System (INIS)

Bowman, T.J.

1998-01-01

Washington Administrative Code (WAC) 173-303-640 specifies that corrosion protection must be designed into tank systems that treat or store dangerous wastes. Project W-320, Waste Retrieval Sluicing System (WRSS), utilizes underground encased waste transfer piping between tanks 241-C-106 and 241-AY-102. Corrosion protection is afforded to the encasements of the WRSS waste transfer piping through the application of earthen ionic currents onto the surface of the piping encasements. Cathodic protection is used in conjunction with the protective coatings that are applied upon the WRSS encasement piping. WRSS installed two new two rectifier systems (46 and 47) and modified one rectifier system (31). WAC 173-303-640 specifies that the proper operation of cathodic protection systems must be confirmed within six months after initial installation. The WRSS cathodic protection systems were energized to begin continuous operation on 5/5/98. Sixteen days after the initial steady-state start-up of the WRSS rectifier systems, the operational testing was accomplished with procedure OTP-320-006 Rev/Mod A-0. This operational test report documents the OTP-320-006 results and documents the results of configuration testing of integrated piping and rectifier systems associated with the W-320 cathodic protection systems

Towards an Intelligent Possibilistic Web Information Retrieval Using Multiagent System

Science.gov (United States)

Elayeb, Bilel; Evrard, Fabrice; Zaghdoud, Montaceur; Ahmed, Mohamed Ben

2009-01-01

Purpose: The purpose of this paper is to make a scientific contribution to web information retrieval (IR). Design/methodology/approach: A multiagent system for web IR is proposed based on new technologies: Hierarchical Small-Worlds (HSW) and Possibilistic Networks (PN). This system is based on a possibilistic qualitative approach which extends the…

Single-Shell Tank (SST) Retrieval Project Plan for Tank 241-C-104 Retrieval

International Nuclear Information System (INIS)

DEFIGH PRICE, C.

2000-01-01

In support of the SST Interim Closure Project, Project W-523 ''Tank 241-C-104 Waste Retrieval System'' will provide systems for retrieval and transfer of radioactive waste from tank 241-C-104 (C-104) to the DST staging tank 241-AY-101 (AY-101). At the conclusion of Project W-523, a retrieval system will have been designed and tested to meet the requirements for Acceptance of Beneficial Use and been turned over to operations. Completion of construction and operations of the C-104 retrieval system will meet the recently proposed near-term Tri-Party Agreement milestone, M-45-03F (Proposed Tri-Party Agreement change request M-45-00-01A, August, 30 2000) for demonstrating limits of retrieval technologies on sludge and hard heels in SSTs, reduce near-term storage risks associated with aging SSTs, and provide feed for the tank waste treatment plant. This Project Plan documents the methodology for managing Project W-523; formalizes responsibilities; identifies key interfaces required to complete the retrieval action; establishes the technical, cost, and schedule baselines; and identifies project organizational requirements pertaining to the engineering process such as environmental, safety, quality assurance, change control, design verification, testing, and operational turnover

Project W-211, initial tank retrieval systems, retrieval control system software configuration management plan

International Nuclear Information System (INIS)

RIECK, C.A.

1999-01-01

This Software Configuration Management Plan (SCMP) provides the instructions for change control of the W-211 Project, Retrieval Control System (RCS) software after initial approval/release but prior to the transfer of custody to the waste tank operations contractor. This plan applies to the W-211 system software developed by the project, consisting of the computer human-machine interface (HMI) and programmable logic controller (PLC) software source and executable code, for production use by the waste tank operations contractor. The plan encompasses that portion of the W-211 RCS software represented on project-specific AUTOCAD drawings that are released as part of the C1 definitive design package (these drawings are identified on the drawing list associated with each C-1 package), and the associated software code. Implementation of the plan is required for formal acceptance testing and production release. The software configuration management plan does not apply to reports and data generated by the software except where specifically identified. Control of information produced by the software once it has been transferred for operation is the responsibility of the receiving organization

Project W-320, 241-C-106 sluicing HVAC calculations, Volume 1

International Nuclear Information System (INIS)

Bailey, J.W.

1998-01-01

This supporting document has been prepared to make the FDNW calculations for Project W-320, readily retrievable. The report contains the following calculations: Exhaust airflow sizing for Tank 241-C-106; Equipment sizing and selection recirculation fan; Sizing high efficiency mist eliminator; Sizing electric heating coil; Equipment sizing and selection of recirculation condenser; Chiller skid system sizing and selection; High efficiency metal filter shielding input and flushing frequency; and Exhaust skid stack sizing and fan sizing

Project W-320, 241-C-106 sluicing HVAC calculations, Volume 1

Energy Technology Data Exchange (ETDEWEB)

Bailey, J.W.

1998-08-07

This supporting document has been prepared to make the FDNW calculations for Project W-320, readily retrievable. The report contains the following calculations: Exhaust airflow sizing for Tank 241-C-106; Equipment sizing and selection recirculation fan; Sizing high efficiency mist eliminator; Sizing electric heating coil; Equipment sizing and selection of recirculation condenser; Chiller skid system sizing and selection; High efficiency metal filter shielding input and flushing frequency; and Exhaust skid stack sizing and fan sizing.

Effect of component design in retrieved bipolar hip hemiarthroplasty systems.

Science.gov (United States)

Hess, Matthew D; Baker, Erin A; Salisbury, Meagan R; Kaplan, Lige M; Greene, Ryan T; Greene, Perry W

2013-09-01

Primary articulation of bipolar hemiarthroplasty systems is at the femoral head-liner interface. The purpose of this study was to compare observed damage modes on 36 retrieved bipolar systems with implant, demographic, intraoperative, and radiographic data to elucidate the effects of component design, specifically locking mechanism, on clinical performance. Retrieved bipolar hip hemiarthroplasty systems of 3 different design types were obtained, disassembled, and evaluated macro- and microscopically for varying modes of wear, including abrasion, burnishing, embedding, scratching, and pitting. Clinical record review and radiographic analysis were performed by a senior orthopedic surgery resident. Average bipolar hip hemiarthroplasty system term of service was 46 months (range, 0.27-187 months). All devices contained wear debris captured within the articulating space between the femoral head and liner. In 31% of patients without infection, lucency was observed on immediate prerevision radiographs. The system with a leaf locking mechanism showed significantly increased radiographically observed osteolysis (P=.03) compared with a system with a stopper ring locking mechanism. In addition, implant design and observed damage modes, including pitting and third-body particle embedding, were significantly associated with radiographically observed osteolysis. Copyright 2013, SLACK Incorporated.

Using a Recommendation System to Support Problem Solving and Case-Based Reasoning Retrieval

Science.gov (United States)

Tawfik, Andrew A.; Alhoori, Hamed; Keene, Charles Wayne; Bailey, Christian; Hogan, Maureen

2018-01-01

In case library learning environments, learners are presented with an array of narratives that can be used to guide their problem solving. However, according to theorists, learners struggle to identify and retrieve the optimal case to solve a new problem. Given the challenges novice face during case retrieval, recommender systems can be embedded…

Health Professionals' Use of Online Information Retrieval Systems and Online Evidence.

Science.gov (United States)

Lialiou, Paschalina; Pavlopoulou, Ioanna; Mantas, John

2016-01-01

Across-sectional survey was designed to determine health professionals' awareness and usage of online evidence retrieval systems in clinical practice. A questionnaire was used to measure professionals' behavior and utilization of online evidences, as well as, reasons and barriers on information retrieval. 439 nurses and physicians from public and private hospitals in Greece formulate the study's sample. The two most common reasons that individuals are using online information systems were for writing scientific manuscripts or filling a knowledge gap. A positive correlation was found between participants with postgraduate studies and information system usage. The majority of them (90,6%) believe that online information systems improves patient care and 67,6% of them had their own experiences on this. More support is needed to nurses and physicians in order to use the online evidence and as a result to improve the provided care and practices.

A vector-product information retrieval system adapted to heterogeneous, distributed computing environments

Science.gov (United States)

Rorvig, Mark E.

1991-01-01

Vector-product information retrieval (IR) systems produce retrieval results superior to all other searching methods but presently have no commercial implementations beyond the personal computer environment. The NASA Electronic Library Systems (NELS) provides a ranked list of the most likely relevant objects in collections in response to a natural language query. Additionally, the system is constructed using standards and tools (Unix, X-Windows, Notif, and TCP/IP) that permit its operation in organizations that possess many different hosts, workstations, and platforms. There are no known commercial equivalents to this product at this time. The product has applications in all corporate management environments, particularly those that are information intensive, such as finance, manufacturing, biotechnology, and research and development.

New data storage and retrieval systems for JET data

Energy Technology Data Exchange (ETDEWEB)

Layne, Richard E-mail: richard.layne@ukaea.org.uk; Wheatley, Martin E-mail: martin.wheatley@ukaea.org.uk

2002-06-01

Since the start of the Joint European Torus (JET), an IBM mainframe has been the main platform for data analysis and storage (J. Comput. Phys. 73 (1987) 85). The mainframe was removed in June 2001 and Solaris and Linux are now the main data storage and analysis platforms. New data storage and retrieval systems have therefore been developed: the Data Warehouse, the JET pulse file server, and the processed pulse file system. In this paper, the new systems will be described, and the design decisions that led to the final systems will be outlined.

New data storage and retrieval systems for JET data

International Nuclear Information System (INIS)

Layne, Richard; Wheatley, Martin

2002-01-01

Since the start of the Joint European Torus (JET), an IBM mainframe has been the main platform for data analysis and storage (J. Comput. Phys. 73 (1987) 85). The mainframe was removed in June 2001 and Solaris and Linux are now the main data storage and analysis platforms. New data storage and retrieval systems have therefore been developed: the Data Warehouse, the JET pulse file server, and the processed pulse file system. In this paper, the new systems will be described, and the design decisions that led to the final systems will be outlined

The Design of an Interactive Data Retrieval System for Casual Users.

Science.gov (United States)

Radhakrishnan, T.; And Others

1982-01-01

Describes an interactive data retrieval system which was designed and implemented for casual users and which incorporates a user-friendly interface, aids to train beginners in use of the system, versatility in output, and error recovery protocols. A 14-item reference list and two figures illustrating system operation and output are included. (JL)

Design and development of a content-based medical image retrieval system for spine vertebrae irregularity.

Science.gov (United States)

Mustapha, Aouache; Hussain, Aini; Samad, Salina Abdul; Zulkifley, Mohd Asyraf; Diyana Wan Zaki, Wan Mimi; Hamid, Hamzaini Abdul

2015-01-16

Content-based medical image retrieval (CBMIR) system enables medical practitioners to perform fast diagnosis through quantitative assessment of the visual information of various modalities. In this paper, a more robust CBMIR system that deals with both cervical and lumbar vertebrae irregularity is afforded. It comprises three main phases, namely modelling, indexing and retrieval of the vertebrae image. The main tasks in the modelling phase are to improve and enhance the visibility of the x-ray image for better segmentation results using active shape model (ASM). The segmented vertebral fractures are then characterized in the indexing phase using region-based fracture characterization (RB-FC) and contour-based fracture characterization (CB-FC). Upon a query, the characterized features are compared to the query image. Effectiveness of the retrieval phase is determined by its retrieval, thus, we propose an integration of the predictor model based cross validation neural network (PMCVNN) and similarity matching (SM) in this stage. The PMCVNN task is to identify the correct vertebral irregularity class through classification allowing the SM process to be more efficient. Retrieval performance between the proposed and the standard retrieval architectures are then compared using retrieval precision (Pr@M) and average group score (AGS) measures. Experimental results show that the new integrated retrieval architecture performs better than those of the standard CBMIR architecture with retrieval results of cervical (AGS > 87%) and lumbar (AGS > 82%) datasets. The proposed CBMIR architecture shows encouraging results with high Pr@M accuracy. As a result, images from the same visualization class are returned for further used by the medical personnel.

System to control contamination during retrieval of buried TRU waste

Science.gov (United States)

Menkhaus, Daniel E.; Loomis, Guy G.; Mullen, Carlan K.; Scott, Donald W.; Feldman, Edgar M.; Meyer, Leroy C.

1993-01-01

A system to control contamination during the retrieval of hazardous waste comprising an outer containment building, an inner containment building, within the outer containment building, an electrostatic radioactive particle recovery unit connected to and in communication with the inner and outer containment buildings, and a contaminate suppression system including a moisture control subsystem, and a rapid monitoring system having the ability to monitor conditions in the inner and outer containment buildings.

Experimental database retrieval system 'DARTS'

International Nuclear Information System (INIS)

Aoyagi, Tetsuo; Tani, Keiji; Haginoya, Hirobumi; Naito, Shinjiro.

1989-02-01

In JT-60, a large tokamak device of Japan Atomic Energy Research Institute (JAERI), a plasma is fired for 5 ∼ 10 seconds at intervals of about 10 minutes. The each firing is called a shot. Plasma diagnostic data are edited as JT-60 experimental database at every shot cycle and are stored in a large-scale computer (FACOM-M780). Experimentalists look up the data for specific shots which they want to analyze and consider. As the total number of shots increases, they find a difficulty in the looking-up work. In order that they can easily access to their objective shot data or shot group data by using a computer terminal, 'DARTS' (DAtabase ReTrieval System) has been developed. This report may provide enough information on DARTS handling for users. (author)

Topological Aspects of Information Retrieval.

Science.gov (United States)

Egghe, Leo; Rousseau, Ronald

1998-01-01

Discusses topological aspects of theoretical information retrieval, including retrieval topology; similarity topology; pseudo-metric topology; document spaces as topological spaces; Boolean information retrieval as a subsystem of any topological system; and proofs of theorems. (LRW)

Model of Recommendation System for for Indexing and Retrieving the Learning Object based on Multiagent System

Directory of Open Access Journals (Sweden)

Ronaldo Lima Rocha Campos

2012-07-01

Full Text Available This paper proposes a multiagent system application model for indexing, retrieving and recommendation learning objects stored in different and heterogeneous repositories. The objects within these repositories are described by filled fields using different metadata standards. The searching mechanism covers several different learning object repositories and the same object can be described in these repositories by the use of different types of fields. Aiming to improve accuracy and coverage in terms of recovering a learning object and improve the signification of the results we propose an information retrieval model based on the multiagent system approach and an ontological model to describe the knowledge domain covered.

Holographic associative memories in document retrieval systems

International Nuclear Information System (INIS)

Becker, P.J.; Bolle, H.; Keller, A.; Kistner, W.; Riecke, W.D.; Wagner, U.

1979-03-01

The objective of this work was the implementation of a holographic memory with associative readout for a document retrieval system. Taking advantage of the favourable properties of holography - associative readout of the memory, parallel processing in the response store - may give shorter response times than sequentially organized data memories. Such a system may also operate in the interactive mode including chain associations. In order to avoid technological difficulties, the experimental setup made use of commercially available components only. As a result an improved holographic structure is proposed which uses volume holograms in photorefractive crystals as storage device. In two chapters of appendix we give a review of the state of the art of electrooptic devices for coherent optical data processing and of competing technologies (semiconductor associative memories and associative program systems). (orig.) [de

Project W-211, initial tank retrieval systems, description of operations for 241-AP-102 and 241-AP-104

Energy Technology Data Exchange (ETDEWEB)

RIECK, C.A.

1999-02-25

The primary purpose of the Initial Tank Retrieval Systems (ITRS) is to provide systems for retrieval of radioactive wastes stored in underground double-shell tanks (DSTS) for transfer to alternate storage, evaporation, pretreatment or treatment, while concurrently reducing risks associated with safety watch list and other DSTs. This Description of Operations (DOO) defines the control philosophy for the waste retrieval system for tanks 241-AP-102 (AP-102) and 241-AP-104 (AP-104). This DOO will provide a basis for the detailed design of the Retrieval Control System (RCS) for AP-102 and AP-104 and establishes test criteria for the RCS. The test criteria will be used during qualification testing and acceptance testing to verify operability.

Project W-211, initial tank retrieval systems, description of operations for 241-AP-102 and 241-AP-104

International Nuclear Information System (INIS)

RIECK, C.A.

1999-01-01

The primary purpose of the Initial Tank Retrieval Systems (ITRS) is to provide systems for retrieval of radioactive wastes stored in underground double-shell tanks (DSTS) for transfer to alternate storage, evaporation, pretreatment or treatment, while concurrently reducing risks associated with safety watch list and other DSTs. This Description of Operations (DOO) defines the control philosophy for the waste retrieval system for tanks 241-AP-102 (AP-102) and 241-AP-104 (AP-104). This DOO will provide a basis for the detailed design of the Retrieval Control System (RCS) for AP-102 and AP-104 and establishes test criteria for the RCS. The test criteria will be used during qualification testing and acceptance testing to verify operability

Multimedia information retrieval theory and techniques

CERN Document Server

Raieli, Roberto

2013-01-01

Novel processing and searching tools for the management of new multimedia documents have developed. Multimedia Information Retrieval (MMIR) is an organic system made up of Text Retrieval (TR); Visual Retrieval (VR); Video Retrieval (VDR); and Audio Retrieval (AR) systems. So that each type of digital document may be analysed and searched by the elements of language appropriate to its nature, search criteria must be extended. Such an approach is known as the Content Based Information Retrieval (CBIR), and is the core of MMIR. This novel content-based concept of information handling needs to be integrated with more traditional semantics. Multimedia Information Retrieval focuses on the tools of processing and searching applicable to the content-based management of new multimedia documents. Translated from Italian by Giles Smith, the book is divided in to two parts. Part one discusses MMIR and related theories, and puts forward new methodologies; part two reviews various experimental and operating MMIR systems, a...

Tank waste remediation system retrieval and disposal mission phase 1 financial analysis

International Nuclear Information System (INIS)

Wells, M.W.

1998-01-01

The purpose of the Tank Waste Remediation System (TWRS) Retrieval and Disposal Mission Phase 1 Financial Analysis is to provide a quantitative and qualitative cost and schedule risk analysis of HNF-1946, Tank Waste Remediation System Retrieval and Disposal Mission Initial Updated Baseline (Swita et al. 1998). The Updated Baseline (Section 3.0) is compared to the current TWRS Project Multi-Year Work Plan (MYWP) for fiscal year (FY) 1998 and target budgets for FY 1999 through FY 2011 (Section 4.1). The analysis then evaluates the executability of HNF-1946 (Sections 4.2 through 4.5) and recommends a path forward for risk mitigation (Sections 4.6, 4.7, and 5.0). A sound systems engineering approach was applied to understand and analyze the Phase 1B Retrieval and Disposal mission. Program and Level 1 Logics were decomposed to Level 8 of the Work Breakdown Structure (WBS) where logic was detailed, scope was defined, detail durations and estimates prepared, and resource loaded schedules developed. Technical Basis Review (TBR) packages were prepared which include this information and, in addition, defined the enabling assumptions for each task, and the risks associated with performance. This process is discussed in Section 2.1. Detailed reviews at the subactivity within the Level 1 Logic TBR levels were conducted to provide the recommended solution to the Phase 1B Retrieval and Disposal Mission. Independent cost analysis and risk assessments were performed by members of the Lockheed Martin Hanford Corporation (LMHC) Business Management and Chief Financial Officer organization along with specialists in risk analysis from TRW, Inc. and Lockheed Martin Energy Systems. The process evaluated technical, schedule, and cost risk by category (program specific fixed and variable, integrated program, and programmatic) based on risk certainly from high probability well defined to very low probability that is not bounded or priceable as discussed in Section 2.2. The results have been

Conceptual designs of automated systems for underground emplacement and retrieval of nuclear waste

International Nuclear Information System (INIS)

Slocum, A.H.; Hou, W.M.; Park, K.; Hochmuth, C.; Thurston, D.C.

1987-01-01

Current designs of underground nuclear waste repositories have not adequately addressed the possibility of automated, unmanned emplacement and retrieval. This report will present design methodologies for development of an automated system for underground emplacement of nuclear waste. By scaling generic issues to different repositories, it is shown that a two vehicle automated waste emplacement/retrieval system can be designed to operate in a fail-safe mode. Evaluation of cost at this time is not possible. Significant gains in worker safety, however, can be realized by minimizing the possibility of human exposure

INIS retrieval service, towards on-line

International Nuclear Information System (INIS)

Ebinuma, Yukio; Komatsubara, Yasutoshi

1983-01-01

Japan Atomic Energy Research Institute executes the retrieval service of INIS atomic energy information by batch system in cooperation with Genshiryoku Kozaikai. This service is very popular to the users in whole Japan, but the demand of on-line service has increased recently. Therefore, it was decided to begin the INIS on-line service from January, 1984, through the on-line information retrieval system of the Japan Information Center of Science and Technology. It is expected that when the operation will be started, the utilization of INIS atomic energy information in Japan will drastically increase. Also Japan Atomic Energy Research Institute has carried out the retrieval service by on-line system for those in the institute besides the batch system, accordingly, at this opportunity, the state of utilization of both systems and their distinction to use effectively, and the operation and the method of utilization of the on-line information retrieval system of JICST are explained. In the on-line system, the users are accessible to the data base themselves, and immediate information retrieval is possible, while in the batch system, the related information can be retrieved without fail, and the troublesome operation of equipment is not necessary. (Kako, I.)

Design package lazy susan for the fuel retrieval system

International Nuclear Information System (INIS)

TEDESCHI, D.J.

1999-01-01

This is a design package that contains the details for a Lazy Susan style small tool for the Fuel Retrieval System. The Lazy Susan tool is used to help rotate an MCO Fuel Basket when loading it. This document contains requirements, development design information, tests and test reports that pertain to the production of Lazy Susan small tool

Monitored Retrievable Storage System Requirements Document. Revision 1

Energy Technology Data Exchange (ETDEWEB)

1994-03-01

This Monitored Retrievable Storage System Requirements Document (MRS-SRD) describes the functions to be performed and technical requirements for a Monitored Retrievable Storage (MRS) facility subelement and the On-Site Transfer and Storage (OSTS) subelement. The MRS facility subelement provides for temporary storage, at a Civilian Radioactive Waste Management System (CRWMS) operated site, of spent nuclear fuel (SNF) contained in an NRC-approved Multi-Purpose Canister (MPC) storage mode, or other NRC-approved storage modes. The OSTS subelement provides for transfer and storage, at Purchaser sites, of spent nuclear fuel (SNF) contained in MPCs. Both the MRS facility subelement and the OSTS subelement are in support of the CRWMS. The purpose of the MRS-SRD is to define the top-level requirements for the development of the MRS facility and the OSTS. These requirements include design, operation, and decommissioning requirements to the extent they impact on the physical development of the MRS facility and the OSTS. The document also presents an overall description of the MRS facility and the OSTS, their functions (derived by extending the functional analysis documented by the Physical System Requirements (PSR) Store Waste Document), their segments, and the requirements allocated to the segments. In addition, the top-level interface requirements of the MRS facility and the OSTS are included. As such, the MRS-SRD provides the technical baseline for the MRS Safety Analysis Report (SAR) design and the OSTS Safety Analysis Report design.

The Wikipedia Image Retrieval Task

NARCIS (Netherlands)

T. Tsikrika (Theodora); J. Kludas

2010-01-01

htmlabstractThe wikipedia image retrieval task at ImageCLEF provides a testbed for the system-oriented evaluation of visual information retrieval from a collection of Wikipedia images. The aim is to investigate the effectiveness of retrieval approaches that exploit textual and visual evidence in the

Retrievals of Ice Cloud Microphysical Properties of Deep Convective Systems using Radar Measurements

Science.gov (United States)

Tian, J.; Dong, X.; Xi, B.; Wang, J.; Homeyer, C. R.

2015-12-01

This study presents innovative algorithms for retrieving ice cloud microphysical properties of Deep Convective Systems (DCSs) using Next-Generation Radar (NEXRAD) reflectivity and newly derived empirical relationships from aircraft in situ measurements in Wang et al. (2015) during the Midlatitude Continental Convective Clouds Experiment (MC3E). With composite gridded NEXRAD radar reflectivity, four-dimensional (space-time) ice cloud microphysical properties of DCSs are retrieved, which is not possible from either in situ sampling at a single altitude or from vertical pointing radar measurements. For this study, aircraft in situ measurements provide the best-estimated ice cloud microphysical properties for validating the radar retrievals. Two statistical comparisons between retrieved and aircraft in situ measured ice microphysical properties are conducted from six selected cases during MC3E. For the temporal-averaged method, the averaged ice water content (IWC) and median mass diameter (Dm) from aircraft in situ measurements are 0.50 g m-3 and 1.51 mm, while the retrievals from radar reflectivity have negative biases of 0.12 g m-3 (24%) and 0.02 mm (1.3%) with correlations of 0.71 and 0.48, respectively. For the spatial-averaged method, the IWC retrievals are closer to the aircraft results (0.51 vs. 0.47 g m-3) with a positive bias of 8.5%, whereas the Dm retrievals are larger than the aircraft results (1.65 mm vs. 1.51 mm) with a positive bias of 9.3%. The retrieved IWCs decrease from ~0.6 g m-3 at 5 km to ~0.15 g m-3 at 13 km, and Dm values decrease from ~2 mm to ~0.7 mm at the same levels. In general, the aircraft in situ measured IWC and Dm values at each level are within one standard derivation of retrieved properties. Good agreements between microphysical properties measured from aircraft and retrieved from radar reflectivity measurements indicate the reasonable accuracy of our retrievals.

”Missing clot” during mechanical thrombectomy in acute stroke using Solitaire stent retrieval system

Directory of Open Access Journals (Sweden)

Vikram Huded

2016-01-01

Full Text Available Stent retrieval system is an established treatment modality in acute ischemic stroke with large vessel occlusion. Here, we describe a complication which occurred during mechanical thrombectomy in three cases where the clot dislodged during retrieval. There was a possibility of the clot getting reinjected into the artery with possible dire consequences.

FORDAT : an information retrieval system for forest economic data

Science.gov (United States)

Henry M. Spelter

1981-01-01

Time series data frequently used in Forest Service studies of wood products consumption have been stored in a data retrieval system on the computer of the University of Wisconsin. The data cover activity in wood processing from forest to end use. Prices and costs at succeeding stages, historical usage, production rates, and other relevant data to wood use analysis were...

Information Retrieval System Design Issues in a Microcomputer-Based Relational DBMS Environment.

Science.gov (United States)

Wolfram, Dietmar

1992-01-01

Outlines the file structure requirements for a microcomputer-based information retrieval system using FoxPro, a relational database management system (DBMS). Issues relating to the design and implementation of such systems are discussed, and two possible designs are examined in terms of space economy and practicality of implementation. (15…

Tank waste remediation system retrieval and disposal mission initial updated baseline summary

International Nuclear Information System (INIS)

Swita, W.R.

1998-01-01

This document provides a summary of the proposed Tank Waste Remediation System Retrieval and Disposal Mission Initial Updated Baseline (scope, schedule, and cost) developed to demonstrate the Tank Waste Remediation System contractor's Readiness-to-Proceed in support of the Phase 1B mission

Retrieval options study

International Nuclear Information System (INIS)

1980-03-01

This Retrieval Options Study is part of the systems analysis activities of the Office of Nuclear Waste Isolation to develop the scientific and technological bases for radioactive waste repositories in various geologic media. The study considers two waste forms, high level waste and spent fuel, and defines various classes of waste retrieval and recovery. A methodology and data base are developed which allow the relative evaluation of retrieval and recovery costs and the following technical criteria: safety; technical feasibility; ease of retrieval; probable intact retrieval time; safeguards; monitoring; criticality; and licensability. A total of 505 repository options are defined and the cost and technical criteria evaluated utilizing a combination of facts and engineering judgments. The repositories evaluated are selected combinations of the following parameters: Geologic Media (salt, granite, basalt, shale); Retrieval Time after Emplacement (5 and 25 years); Emplacement Design (nominal hole, large hole, carbon steel canister, corrosion resistant canister, backfill in hole, nominal sleeves, thick wall sleeves); Emplacement Configuration (single vertical, multiple vertical, single horizontal, multiple horizontal, vaults; Thermal Considerations; (normal design, reduced density, once-through ventilation, recirculated ventilation); Room Backfill; (none, run-of-mine, early, 5 year delay, 25 year delay, decommissioned); and Rate of Retrieval;

Definition of an automatic information retrieval system independent from the data base used

International Nuclear Information System (INIS)

Cunha, E.R.

1983-04-01

A bibliographic information retrieval system using data stored at the standardized interchange format ISO 2709 or ANSI Z39.2, is specified. A set of comands for interchange format manipulation wich allows the data access at the logical level, achieving the data independence, are used. A data base description language, a storage structure and data base manipulation comands are specified, using retrieval techniques which consider the applications needs. (Author) [pt

MRS [monitored retrievable storage] to transportation system interfaces

International Nuclear Information System (INIS)

Row, T.H.; Croff, A.G.

1987-01-01

In March 1987, the US Department of Energy presented to Congress the proposal to construct and operate a facility for the monitored retrievable storage (MRS) of spent fuel at a site on the Clinch River in the Roane County portions of Oak Ridge. In discussing the MRS to Transportation System Interfaces, the authors provide a blending of the technical and institutional issues, for they do not believe the solutions to success of this enterprise lie wholly in one area. The authors cover: early chronology of the MRS; comparison of total-system life cycle cost estimates of the authorized system and improved-performance system (i.e., the system that includes a facility for MRS); transportation costs resulting from shipping, security and cask; assumptions for dedicated rail transport from MRS to repository; and significant results from the Total System Life Cycle Cost (TSLCC) analysis of the improved performance system. (AT)

Unified modeling language and design of a case-based retrieval system in medical imaging.

Science.gov (United States)

LeBozec, C; Jaulent, M C; Zapletal, E; Degoulet, P

1998-01-01

One goal of artificial intelligence research into case-based reasoning (CBR) systems is to develop approaches for designing useful and practical interactive case-based environments. Explaining each step of the design of the case-base and of the retrieval process is critical for the application of case-based systems to the real world. We describe herein our approach to the design of IDEM--Images and Diagnosis from Examples in Medicine--a medical image case-based retrieval system for pathologists. Our approach is based on the expressiveness of an object-oriented modeling language standard: the Unified Modeling Language (UML). We created a set of diagrams in UML notation illustrating the steps of the CBR methodology we used. The key aspect of this approach was selecting the relevant objects of the system according to user requirements and making visualization of cases and of the components of the case retrieval process. Further evaluation of the expressiveness of the design document is required but UML seems to be a promising formalism, improving the communication between the developers and users.

TBIdoc: 3D content-based CT image retrieval system for traumatic brain injury

Science.gov (United States)

Li, Shimiao; Gong, Tianxia; Wang, Jie; Liu, Ruizhe; Tan, Chew Lim; Leong, Tze Yun; Pang, Boon Chuan; Lim, C. C. Tchoyoson; Lee, Cheng Kiang; Tian, Qi; Zhang, Zhuo

2010-03-01

Traumatic brain injury (TBI) is a major cause of death and disability. Computed Tomography (CT) scan is widely used in the diagnosis of TBI. Nowadays, large amount of TBI CT data is stacked in the hospital radiology department. Such data and the associated patient information contain valuable information for clinical diagnosis and outcome prediction. However, current hospital database system does not provide an efficient and intuitive tool for doctors to search out cases relevant to the current study case. In this paper, we present the TBIdoc system: a content-based image retrieval (CBIR) system which works on the TBI CT images. In this web-based system, user can query by uploading CT image slices from one study, retrieval result is a list of TBI cases ranked according to their 3D visual similarity to the query case. Specifically, cases of TBI CT images often present diffuse or focal lesions. In TBIdoc system, these pathological image features are represented as bin-based binary feature vectors. We use the Jaccard-Needham measure as the similarity measurement. Based on these, we propose a 3D similarity measure for computing the similarity score between two series of CT slices. nDCG is used to evaluate the system performance, which shows the system produces satisfactory retrieval results. The system is expected to improve the current hospital data management in TBI and to give better support for the clinical decision-making process. It may also contribute to the computer-aided education in TBI.

Information visualization to user-friendly interface construction for information retrieval systems

Directory of Open Access Journals (Sweden)

Jessica Monique de Lira Vieira

2011-10-01

Full Text Available The information presented through visualization help the Information Retrieval System (IRS to reach its main goal: to retrieve relevant information that meets the informational needs of its users. The objective of this article is to describe and analyze techniques proposed by the Information Visualization area and interface models discussed in Information Science Literature, which applied to graphical interface construction would facilitate the appropriation of information by the users of IRS and would help them to search, browse and retrieve information. The methodology consists of a literature review focusing on the potential contribution of the visual representation of information in the development of user-friendly interfaces to IRS, as well as identification and analyses of visualizations used as interfaces by IRS. The use of visualizations is of great importance in the communication between SRI and users, because the information presented through visual representation are better understood by user and allow the discovery of new knowledge.

Preliminary fire hazards analysis for W-211, Initial Tank Retrieval Systems

International Nuclear Information System (INIS)

Huckfeldt, R.A.

1995-01-01

A fire hazards analysis (FHA) was performed for Project W-211, Initial Tank Retrieval System (ITRS), at the Department of Energy (DOE) Hanford site. The objectives of this FHA was to determine (1) the fire hazards that expose the Initial Tank Retrieval System or are inherent in the process, (2) the adequacy of the fire-safety features planned, and (3) the degree of compliance of the project with specific fire safety provisions in DOE orders and related engineering codes and standards. The scope included the construction, the process hazards, building fire protection, and site wide fire protection. The results are presented in terms of the fire hazards present, the potential extent of fire damage, and the impact on employees and public safety. This study evaluated the ITRS with respect to its use at Tank 241-SY-101 only

Intelligent Information Retrieval: An Introduction.

Science.gov (United States)

Gauch, Susan

1992-01-01

Discusses the application of artificial intelligence to online information retrieval systems and describes several systems: (1) CANSEARCH, from MEDLINE; (2) Intelligent Interface for Information Retrieval (I3R); (3) Gausch's Query Reformulation; (4) Environmental Pollution Expert (EP-X); (5) PLEXUS (gardening); and (6) SCISOR (corporate…

Tank waste remediation system retrieval and disposal mission key enabling assumptions

International Nuclear Information System (INIS)

Baldwin, J.H.

1998-01-01

An overall systems approach has been applied to develop action plans to support the retrieval and immobilization waste disposal mission. The review concluded that the systems and infrastructure required to support the mission are known. Required systems are either in place or plans have been developed. An analysis of the programmatic, management and technical activities necessary to declare Readiness to Proceed with execution of the mission demonstrates that the system, people, and hardware will be on line and ready to support the private contractors. The systems approach included defining the retrieval and immobilized waste disposal mission requirements and evaluating the readiness of the TWRS contractor to supply waste feed to the private contractors in June 2002. The Phase 1 feed delivery requirements from the Private Contractor Request for Proposals were reviewed, transfer piping routes were mapped on it, existing systems were evaluated, and upgrade requirements were defined. Technical Basis Reviews were completed to define work scope in greater detail, cost estimates and associated year by year financial analyses were completed. Personnel training, qualifications, management systems and procedures were reviewed and shown to be in place and ready to support the Phase 1B mission. Key assumptions and risks that could negatively impact mission success were evaluated and appropriate mitigative actions plans were planned and scheduled

AEROMETRIC INFORMATION RETRIEVAL SYSTEM (AIRS) -GEOGRAPHIC, COMMON, AND MAINTENANCE SUBSYSTEM (GCS)

Science.gov (United States)

Aerometric Information Retrieval System (AIRS) is a computer-based repository of information about airborne pollution in the United States and various World Health Organization (WHO) member countries. AIRS is administered by the U.S. Environmental Protection Agency, and runs on t...

Design Package for Fuel Retrieval System Fuel Handling Tool Modification

International Nuclear Information System (INIS)

TEDESCHI, D.J.

2000-01-01

This is a design package that contains the details for a modification to a tool used for moving fuel elements during loading of MCO Fuel Baskets for the Fuel Retrieval System. The tool is called the fuel handling tool (or stinger). This document contains requirements, development design information, tests, and test reports

Information retrieval system: impacts of water-level changes on uses of federal storage reservoirs of the Columbia River.

Energy Technology Data Exchange (ETDEWEB)

Fickeisen, D.H.; Cowley, P.J.; Neitzel, D.A.; Simmons, M.A.

1982-09-01

A project undertaken to provide the Bonneville Power Administration (BPA) with information needed to conduct environmental assessments and meet requirements of the National Environmental Policy Act (NEPA) and the Pacific Northwest Electric Power Planning and Conservation Act (Regional Act) is described. Access to information on environmental effects would help BPA fulfill its responsibilities to coordinate power generation on the Columbia River system, protect uses of the river system (e.g., irrigation, recreation, navigation), and enhance fish and wildlife production. Staff members at BPA identified the need to compile and index information resources that would help answer environmental impact questions. A computer retrieval system that would provide ready access to the information was envisioned. This project was supported by BPA to provide an initial step toward a compilation of environmental impact information. Scientists at Pacific Northwest Laboratory (PNL) identified, gathered, and evaluated information related to environmental effects of water level on uses of five study reservoirs and developed and implemented and environmental data retrieval system, which provides for automated storage and retrieval of annotated citations to published and unpublished information. The data retrieval system is operating on BPA's computer facility and includes the reservoir water-level environmental data. This project was divided into several tasks, some of which were conducted simultaneously to meet project deadlines. The tasks were to identify uses of the five study reservoirs, compile and evaluate reservoir information, develop a data entry and retrieval system, identify and analyze research needs, and document the data retrieval system and train users. Additional details of the project are described in several appendixes.

Extended capture range for focus-diverse phase retrieval in segmented aperture systems using geometrical optics.

Science.gov (United States)

Jurling, Alden S; Fienup, James R

2014-03-01

Extending previous work by Thurman on wavefront sensing for segmented-aperture systems, we developed an algorithm for estimating segment tips and tilts from multiple point spread functions in different defocused planes. We also developed methods for overcoming two common modes for stagnation in nonlinear optimization-based phase retrieval algorithms for segmented systems. We showed that when used together, these methods largely solve the capture range problem in focus-diverse phase retrieval for segmented systems with large tips and tilts. Monte Carlo simulations produced a rate of success better than 98% for the combined approach.

Retrieval options study

Energy Technology Data Exchange (ETDEWEB)

1980-03-01

This Retrieval Options Study is part of the systems analysis activities of the Office of Nuclear Waste Isolation to develop the scientific and technological bases for radioactive waste repositories in various geologic media. The study considers two waste forms, high level waste and spent fuel, and defines various classes of waste retrieval and recovery. A methodology and data base are developed which allow the relative evaluation of retrieval and recovery costs and the following technical criteria: safety; technical feasibility; ease of retrieval; probable intact retrieval time; safeguards; monitoring; criticality; and licensability. A total of 505 repository options are defined and the cost and technical criteria evaluated utilizing a combination of facts and engineering judgments. The repositories evaluated are selected combinations of the following parameters: Geologic Media (salt, granite, basalt, shale); Retrieval Time after Emplacement (5 and 25 years); Emplacement Design (nominal hole, large hole, carbon steel canister, corrosion resistant canister, backfill in hole, nominal sleeves, thick wall sleeves); Emplacement Configuration (single vertical, multiple vertical, single horizontal, multiple horizontal, vaults; Thermal Considerations; (normal design, reduced density, once-through ventilation, recirculated ventilation); Room Backfill; (none, run-of-mine, early, 5 year delay, 25 year delay, decommissioned); and Rate of Retrieval; (same as emplacement, variably slower depending on repository/canister condition).

Vocabulary Control for Information Retrieval.

Science.gov (United States)

Lancaster, F. W.

This book deals with properties of vocabularies for indexing and searching document collections; the construction, organization, display, and maintenance of these vocabularies; and the vocabulary as a factor affecting the performance of retrieval systems. Most of the text is concerned with vocabularies for post-coordinate retrieval systems, with…

Automated Storage Retrieval System (ASRS) Role Towards Achievement of Safety Objective and Safety Culture in Radioactive Storage Facilities

International Nuclear Information System (INIS)

Mohamad Hakiman Mohd Yusoff; Nurul Wahida Ahmad Khairuddin; Nik Marzukee Nik Ibrahim; Mat Bakar Mahusin; Muhammad, Z.A.; Nur Azna Mahmud; Norfazlina Zainal Abidin

2012-01-01

Waste Technology Development Centre (WasTeC) has been awarded with quality management system ISO 9001:2000 in June 2004 or now known as ISO 9001:2008. The scope of the unit's ISO certification is radioactive waste management and storage of radioactive material. To meet the objectives and requirements ISO 9001:2008, WasTeC has started a project known as Automated Storage and Retrieval System (ASRS). ASRS is a computing controlled method for automatically depositing and retrieving waste from defined locations. The system is used to replace the existing process of storage and retrieval of radioactive waste at storage facility at block 33.The main objective of this project is to reduced the radiation exposure to the worker and potential forklift accident occur during storage and retrieval of the radioactive waste. By using the ASRS system, WasTeC/ Nuclear Malaysia can provide a safe storage of radioactive waste and the use of this system can eliminate the repeat handling and can improve productivity. (author)

Rheological evaluation of simulated neutralized current acid waste

International Nuclear Information System (INIS)

Fow, C.L.; McCarthy, D.; Thornton, G.T.

1986-06-01

A byproduct of the Purex process is an aqueous waste stream that contains fission products. This waste stream, called current acid waste, is chemically neutralized and stored in double shell tanks on the Hanford Site. This neutralized current acid waste (NCAW) will be transported by pipe to B-Plant, a processing plant on the Hanford Site. Rheological and transport properties of NCAW slurry were evaluated. First, researchers conducted lab rheological evaluations of simulated NCAW. The results of these evaluations were then correlated with classical rheological models and scaled up to predict the performance that is likely to occur in the full-scale system. The NCAW in the tank will either be retrieved as is, i.e., no change in the concentration presently in the tank, or will be slightly concentrated before retrieval. Sluicing may be required to retrieve the solids. Three concentrations of simulated NCAW were evaluated that would simulate the different retrieval options: NCAW in the concentration that is presently in the tank; a slightly concentrated NCAW, called NCAW5.5; and equal parts of NCAW settled solids and water (simulating the sluicing stage), called NCAW1:1. The physical and rheological properties of three samples of each concentration at 25 and 100 0 C were evaluated in the laboratory. The properties displayed by NCAW and NCAW5.5 at 25 and 100 0 C allowed it to be classified as a pseudoplastic non-Newtonian fluid. NCAW1:1 at 25 and 100 0 C displayed properties of a yield-pseudoplastic non-Newtonian fluid. The classical non-Newtonian models for pseudoplastic and yield-pseudoplastic fluids were used with the laboratory data to predict the full-scale pump-pipe network parameters

CLASSIFICATION OF THE MGR WASTE EMPLACEMENT/RETRIEVAL SYSTEM

International Nuclear Information System (INIS)

J.A. Ziegler

2000-01-01

The purpose of this analysis is to document the Quality Assurance (QA) classification of the Monitored Geologic Repository (MGR) waste emplacement/retrieved system structures, systems and components (SSCs) performed by the MGR Preclosure Safety and Systems Engineering Section. This analysis also provides the basis for revision of YMP/90-55Q, Q-List (YMP 2000). The Q-List identifies those MGR SSCs subject to the requirements of DOE/RW-0333P, Quality Assurance Requirements and Description (QARD) (DOE 2000). This QA classification incorporates the current MGR design and the results of the ''Design Basis Event Frequency and Dose Calculation for Site Recommendation'' (CRWMS M andO 2000a). The content and technical approach of this analysis is in accordance with the development plan ''QA Classification of MGR Structures, Systems, and Components'' (CRWMS M andO 1999b)

Decision and systems analysis for underground storage tank waste retrieval systems and tank waste remediation system

International Nuclear Information System (INIS)

Bitz, D.A.; Berry, D.L.; Jardine, L.J.

1994-03-01

Hanford's underground tanks (USTs) pose one of the most challenging hazardous and radioactive waste problems for the Department of Energy (DOE). Numerous schemes have been proposed for removing the waste from the USTs, but the technology options for doing this are largely unproven. To help assess the options, an Independent Review Group (IRG) was established to conduct a broad review of retrieval systems and the tank waste remediation system. The IRG consisted of the authors of this report

Interactive Information Retrieval

DEFF Research Database (Denmark)

Borlund, Pia

2013-01-01

The paper introduces the research area of interactive information retrieval (IIR) from a historical point of view. Further, the focus here is on evaluation, because much research in IR deals with IR evaluation methodology due to the core research interest in IR performance, system interaction...... and satisfaction with retrieved information. In order to position IIR evaluation, the Cranfield model and the series of tests that led to the Cranfield model are outlined. Three iconic user-oriented studies and projects that all have contributed to how IIR is perceived and understood today are presented......: The MEDLARS test, the Book House fiction retrieval system, and the OKAPI project. On this basis the call for alternative IIR evaluation approaches motivated by the three revolutions (the cognitive, the relevance, and the interactive revolutions) put forward by Robertson & Hancock-Beaulieu (1992) is presented...

Tank Waste Remediation System retrieval and disposal mission technical baseline summary description

International Nuclear Information System (INIS)

McLaughlin, T.J.

1998-01-01

This document is prepared in order to support the US Department of Energy's evaluation of readiness-to-proceed for the Waste Retrieval and Disposal Mission at the Hanford Site. The Waste Retrieval and Disposal Mission is one of three primary missions under the Tank Waste Remediation System (TWRS) Project. The other two include programs to characterize tank waste and to provide for safe storage of the waste while it awaits treatment and disposal. The Waste Retrieval and Disposal Mission includes the programs necessary to support tank waste retrieval, wastefeed, delivery, storage and disposal of immobilized waste, and closure of tank farms. This mission will enable the tank farms to be closed and turned over for final remediation. The Technical Baseline is defined as the set of science and engineering, equipment, facilities, materials, qualified staff, and enabling documentation needed to start up and complete the mission objectives. The primary purposes of this document are (1) to identify the important technical information and factors that should be used by contributors to the mission and (2) to serve as a basis for configuration management of the technical information and factors

PEOPLE RETRIEVAL BY MEANS OF COMPOSITE PICTURES: METHODS, SYSTEMS AND PRACTICAL DECISIONS

Directory of Open Access Journals (Sweden)

G. A. Kukharev

2015-07-01

Full Text Available We discuss the problem of people retrieval by means of composite pictures and methods of its practical realization. Earlier on, the problem was posed in the previous paper by the authors, and this paper deals with its further development. The starting premise here is that for the successful search of people by their sketches it is necessary to transform these sketches into sets of populations of sketches imitating evidence of «group of witnesses» and evidence with incomplete information in verbal portraits. Variants of structures for benchmark «photo-sketch» databases are presented, intended for modeling and practical realization of original photos retrieval by sketches, which new component is a population of sketches. Problems of preprocessing for initial sketches and original photos and its influence on the result of their comparison are discussed. Simple sketch recognition systems (Simple FaRetSys and a problem of original photos retrieval by the sketches are considered. Shortcomings of such systems are shown and new decisions on extending and development of simple systems (Extended FaRetSys are presented. Experiments on searching of original photos by sketches in the CUFS database of sketches and similar experiments on widely known FERET and CUFSF facial databases are presented. Three frameworks are offered for retrieval performance improvement. In the first one, original sketches are transformed into populations, and then in these populations the sketch similar to the given sketch (Forensic Sketch is already defined. The class of the sketch found in a population «by definition» unambiguously corresponds to a class of the original photo. In the second framework, the Forensic Sketch is transformed to a population of sketches, and all original sketches in a benchmarking database are compared to sketches from populations of the Forensic Sketch. The class of matches is determined in the same manner as in the first framework. The third

Adaptive neuro-fuzzy inference system for temperature and humidity profile retrieval from microwave radiometer observations

Science.gov (United States)

Ramesh, K.; Kesarkar, A. P.; Bhate, J.; Venkat Ratnam, M.; Jayaraman, A.

2015-01-01

The retrieval of accurate profiles of temperature and water vapour is important for the study of atmospheric convection. Recent development in computational techniques motivated us to use adaptive techniques in the retrieval algorithms. In this work, we have used an adaptive neuro-fuzzy inference system (ANFIS) to retrieve profiles of temperature and humidity up to 10 km over the tropical station Gadanki (13.5° N, 79.2° E), India. ANFIS is trained by using observations of temperature and humidity measurements by co-located Meisei GPS radiosonde (henceforth referred to as radiosonde) and microwave brightness temperatures observed by radiometrics multichannel microwave radiometer MP3000 (MWR). ANFIS is trained by considering these observations during rainy and non-rainy days (ANFIS(RD + NRD)) and during non-rainy days only (ANFIS(NRD)). The comparison of ANFIS(RD + NRD) and ANFIS(NRD) profiles with independent radiosonde observations and profiles retrieved using multivariate linear regression (MVLR: RD + NRD and NRD) and artificial neural network (ANN) indicated that the errors in the ANFIS(RD + NRD) are less compared to other retrieval methods. The Pearson product movement correlation coefficient (r) between retrieved and observed profiles is more than 92% for temperature profiles for all techniques and more than 99% for the ANFIS(RD + NRD) technique Therefore this new techniques is relatively better for the retrieval of temperature profiles. The comparison of bias, mean absolute error (MAE), RMSE and symmetric mean absolute percentage error (SMAPE) of retrieved temperature and relative humidity (RH) profiles using ANN and ANFIS also indicated that profiles retrieved using ANFIS(RD + NRD) are significantly better compared to the ANN technique. The analysis of profiles concludes that retrieved profiles using ANFIS techniques have improved the temperature retrievals substantially; however, the retrieval of RH by all techniques considered in this paper (ANN, MVLR and

Multimodal medical information retrieval with unsupervised rank fusion.

Science.gov (United States)

Mourão, André; Martins, Flávio; Magalhães, João

2015-01-01

Modern medical information retrieval systems are paramount to manage the insurmountable quantities of clinical data. These systems empower health care experts in the diagnosis of patients and play an important role in the clinical decision process. However, the ever-growing heterogeneous information generated in medical environments poses several challenges for retrieval systems. We propose a medical information retrieval system with support for multimodal medical case-based retrieval. The system supports medical information discovery by providing multimodal search, through a novel data fusion algorithm, and term suggestions from a medical thesaurus. Our search system compared favorably to other systems in 2013 ImageCLEFMedical. Copyright © 2014 Elsevier Ltd. All rights reserved.

K Basins floor sludge retrieval system knockout pot basket fuel burn accident

International Nuclear Information System (INIS)

HUNT, J.W.

1998-01-01

The K Basins Sludge Retrieval System Preliminary Hazard Analysis Report (HNF-2676) identified and categorized a series of potential accidents associated with K Basins Sludge Retrieval System design and operation. The fuel burn accident was of concern with respect to the potential release of contamination resulting from a runaway chemical reaction of the uranium fuel in a knockout pot basket suspended in the air. The unmitigated radiological dose to an offsite receptor from this fuel burn accident is calculated to be much less than the offsite risk evaluation guidelines for anticipated events. However, because of potential radiation exposure to the facility worker, this accident is precluded with a safety significant lifting device that will prevent the monorail hoist from lifting the knockout pot basket out of the K Basin water pool

Enhancing Image Retrieval System Using Content Based Search ...

African Journals Online (AJOL)

The output shows more efficiency in retrieval because instead of performing the search on the entire image database, the image category option directs the retrieval engine to the specified category. Also, there is provision to update or modify the different image categories in the image database as need arise. Keywords: ...

Assimilation of SMOS Retrieved Soil Moisture into the Land Information System

Science.gov (United States)

Blankenship, Clay; Case, Jonathan; Zavodsky, Bradley; Jedlovec, Gary

2014-01-01

Soil moisture retrievals from the Soil Moisture and Ocean Salinity (SMOS) instrument are assimilated into the Noah land surface model (LSM) within the NASA Land Information System (LIS). Before assimilation, SMOS retrievals are bias-corrected to match the model climatological distribution using a Cumulative Distribution Function (CDF) matching approach. Data assimilation is done via the Ensemble Kalman Filter. The goal is to improve the representation of soil moisture within the LSM, and ultimately to improve numerical weather forecasts through better land surface initialization. We present a case study showing a large area of irrigation in the lower Mississippi River Valley, in an area with extensive rice agriculture. High soil moisture value in this region are observed by SMOS, but not captured in the forcing data. After assimilation, the model fields reflect the observed geographic patterns of soil moisture. Plans for a modeling experiment and operational use of the data are given. This work helps prepare for the assimilation of Soil Moisture Active/Passive (SMAP) retrievals in the near future.

Semantic-based surveillance video retrieval.

Science.gov (United States)

Hu, Weiming; Xie, Dan; Fu, Zhouyu; Zeng, Wenrong; Maybank, Steve

2007-04-01

Visual surveillance produces large amounts of video data. Effective indexing and retrieval from surveillance video databases are very important. Although there are many ways to represent the content of video clips in current video retrieval algorithms, there still exists a semantic gap between users and retrieval systems. Visual surveillance systems supply a platform for investigating semantic-based video retrieval. In this paper, a semantic-based video retrieval framework for visual surveillance is proposed. A cluster-based tracking algorithm is developed to acquire motion trajectories. The trajectories are then clustered hierarchically using the spatial and temporal information, to learn activity models. A hierarchical structure of semantic indexing and retrieval of object activities, where each individual activity automatically inherits all the semantic descriptions of the activity model to which it belongs, is proposed for accessing video clips and individual objects at the semantic level. The proposed retrieval framework supports various queries including queries by keywords, multiple object queries, and queries by sketch. For multiple object queries, succession and simultaneity restrictions, together with depth and breadth first orders, are considered. For sketch-based queries, a method for matching trajectories drawn by users to spatial trajectories is proposed. The effectiveness and efficiency of our framework are tested in a crowded traffic scene.

Drift-scale thermomechanical analysis for the retrievability systems study

International Nuclear Information System (INIS)

Tsai, F.C.

1996-01-01

A numerical method was used to estimate the stability of potential emplacement drifts without considering a ground support system as a part of the Thermal Loading Systems Study for the Yucca Mountain Site Characterization Project. The stability of the drift is evaluated with two variables: the level of thermal loading and the diameter of the emplacement drift. The analyses include the thermomechanical effects generated by the excavation of the drift, subsequently by the thermal loads from heat-emitting waste packages, and finally by the thermal reduction resulting from rapid cooling ventilation required for the waste retrieval if required. The Discontinuous Deformation Analysis (DDA) code was used to analyze the thermomechanical response of the rock mass of multiple blocks separated by joints. The result of this stability analysis is used to discuss the geomechanical considerations for the advanced conceptual design (ACD) with respect to retrievability. In particular, based on the rock mass strength of the host rock described in the current version of the Reference Information Base, the computed thermal stresses, generated by 111 MTU/acre thermal loads in the near field at 100 years after waste emplacement, is beyond the criterion for the rock mass strength used to predict the stability of the rock mass surrounding the emplacement drift

Single shell tank sluicing history and failure frequency

International Nuclear Information System (INIS)

HERTZEL, J.S.

1998-01-01

This document assesses the potential for failure of the single-shell tanks (SSTs) that are presumably sound and helps to establish the retrieval priorities for these and the assumed leakers. Furthermore, this report examines probabilities of SST failure as a function of age and operational history, and provides a simple statistical summary of historical leak volumes, leak rates, and corrosion factor

Use of information-retrieval languages in automated retrieval of experimental data from long-term storage

Science.gov (United States)

Khovanskiy, Y. D.; Kremneva, N. I.

1975-01-01

Problems and methods are discussed of automating information retrieval operations in a data bank used for long term storage and retrieval of data from scientific experiments. Existing information retrieval languages are analyzed along with those being developed. The results of studies discussing the application of the descriptive 'Kristall' language used in the 'ASIOR' automated information retrieval system are presented. The development and use of a specialized language of the classification-descriptive type, using universal decimal classification indices as the main descriptors, is described.

Interactive information seeking, behaviour and retrieval

CERN Document Server

Ruthven, Ian

2011-01-01

Information retrieval (IR) is a complex human activity supported by sophisticated systems. This book covers the whole spectrum of information retrieval, including: history and background information; behaviour and seeking task-based information; searching and retrieval approaches to investigating information; and, evaluation interfaces for IR.

Using the fuzzy modeling for the retrieval algorithms

International Nuclear Information System (INIS)

Mohamed, A.H

2010-01-01

A rapid growth in number and size of images in databases and world wide web (www) has created a strong need for more efficient search and retrieval systems to exploit the benefits of this large amount of information. However, the collection of this information is now based on the image technology. One of the limitations of the current image analysis techniques necessitates that most image retrieval systems use some form of text description provided by the users as the basis to index and retrieve images. To overcome this problem, the proposed system introduces the using of fuzzy modeling to describe the image by using the linguistic ambiguities. Also, the proposed system can include vague or fuzzy terms in modeling the queries to match the image descriptions in the retrieval process. This can facilitate the indexing and retrieving process, increase their performance and decrease its computational time . Therefore, the proposed system can improve the performance of the traditional image retrieval algorithms.

Information retrieval in particle physics

International Nuclear Information System (INIS)

Oyanagi, Yoshio

1983-01-01

Various information retrieval systems for elementary particle physics are introduced. Scientific information has been distributed in the form of books, periodicals or preprints. Some periodicals include the abstracts of information only. Recently, computer systems, by which the information retrieval can be easily done, have been developed. The construction of networks connecting various computer systems is in progress. It is possible to call the data base of Rutherford Laboratory from a telephone terminal of Laurence Berkeley Laboratory. The access to the Network by British Science Research Council can be made from DESY or CERN. The examples of on-line information retrieval in Japan are presented. Some of the periodicals of secondary information and data books are also introduced. (Kato, T.)

A passage retrieval method based on probabilistic information retrieval model and UMLS concepts in biomedical question answering.

Science.gov (United States)

Sarrouti, Mourad; Ouatik El Alaoui, Said

2017-04-01

Passage retrieval, the identification of top-ranked passages that may contain the answer for a given biomedical question, is a crucial component for any biomedical question answering (QA) system. Passage retrieval in open-domain QA is a longstanding challenge widely studied over the last decades. However, it still requires further efforts in biomedical QA. In this paper, we present a new biomedical passage retrieval method based on Stanford CoreNLP sentence/passage length, probabilistic information retrieval (IR) model and UMLS concepts. In the proposed method, we first use our document retrieval system based on PubMed search engine and UMLS similarity to retrieve relevant documents to a given biomedical question. We then take the abstracts from the retrieved documents and use Stanford CoreNLP for sentence splitter to make a set of sentences, i.e., candidate passages. Using stemmed words and UMLS concepts as features for the BM25 model, we finally compute the similarity scores between the biomedical question and each of the candidate passages and keep the N top-ranked ones. Experimental evaluations performed on large standard datasets, provided by the BioASQ challenge, show that the proposed method achieves good performances compared with the current state-of-the-art methods. The proposed method significantly outperforms the current state-of-the-art methods by an average of 6.84% in terms of mean average precision (MAP). We have proposed an efficient passage retrieval method which can be used to retrieve relevant passages in biomedical QA systems with high mean average precision. Copyright © 2017 Elsevier Inc. All rights reserved.

A prototype feature system for feature retrieval using relationships

Science.gov (United States)

Choi, J.; Usery, E.L.

2009-01-01

Using a feature data model, geographic phenomena can be represented effectively by integrating space, theme, and time. This paper extends and implements a feature data model that supports query and visualization of geographic features using their non-spatial and temporal relationships. A prototype feature-oriented geographic information system (FOGIS) is then developed and storage of features named Feature Database is designed. Buildings from the U.S. Marine Corps Base, Camp Lejeune, North Carolina and subways in Chicago, Illinois are used to test the developed system. The results of the applications show the strength of the feature data model and the developed system 'FOGIS' when they utilize non-spatial and temporal relationships in order to retrieve and visualize individual features.

Mobile Application Development: Component Retrieval System

Data.gov (United States)

National Aeronautics and Space Administration — The purpose of this project was to investigate requirements to develop an innovative mobile application to retrieve components’ detailed information from the Stennis...

Probabilistic and machine learning-based retrieval approaches for biomedical dataset retrieval

Science.gov (United States)

Karisani, Payam; Qin, Zhaohui S; Agichtein, Eugene

2018-01-01

Abstract The bioCADDIE dataset retrieval challenge brought together different approaches to retrieval of biomedical datasets relevant to a user’s query, expressed as a text description of a needed dataset. We describe experiments in applying a data-driven, machine learning-based approach to biomedical dataset retrieval as part of this challenge. We report on a series of experiments carried out to evaluate the performance of both probabilistic and machine learning-driven techniques from information retrieval, as applied to this challenge. Our experiments with probabilistic information retrieval methods, such as query term weight optimization, automatic query expansion and simulated user relevance feedback, demonstrate that automatically boosting the weights of important keywords in a verbose query is more effective than other methods. We also show that although there is a rich space of potential representations and features available in this domain, machine learning-based re-ranking models are not able to improve on probabilistic information retrieval techniques with the currently available training data. The models and algorithms presented in this paper can serve as a viable implementation of a search engine to provide access to biomedical datasets. The retrieval performance is expected to be further improved by using additional training data that is created by expert annotation, or gathered through usage logs, clicks and other processes during natural operation of the system. Database URL: https://github.com/emory-irlab/biocaddie

RETRIEVAL EVENTS EVALUATION

International Nuclear Information System (INIS)

Wilson, T.

1999-01-01

The purpose of this analysis is to evaluate impacts to the retrieval concept presented in the Design Analysis ''Retrieval Equipment and Strategy'' (Reference 6), from abnormal events based on Design Basis Events (DBE) and Beyond Design Basis Events (BDBE) as defined in two recent analyses: (1) DBE/Scenario Analysis for Preclosure Repository Subsurface Facilities (Reference 4); and (2) Preliminary Preclosure Design Basis Event Calculations for the Monitored Geologic Repository (Reference 5) The objective of this task is to determine what impacts the DBEs and BDBEs have on the equipment developed for retrieval. The analysis lists potential impacts and recommends changes to be analyzed in subsequent design analyses for developed equipment, or recommend where additional equipment may be needed, to allow retrieval to be performed in all DBE or BDBE situations. This analysis supports License Application design and therefore complies with the requirements of Systems Description Document input criteria comparison as presented in Section 7, Conclusions. In addition, the analysis discusses the impacts associated with not using concrete inverts in the emplacement drifts. The ''Retrieval Equipment and Strategy'' analysis was based on a concrete invert configuration in the emplacement drift. The scope of the analysis, as presented in ''Development Plan for Retrieval Events Evaluation'' (Reference 3) includes evaluation and criteria of the following: Impacts to retrieval from the emplacement drift based on DBE/BDBEs, and changes to the invert configuration for the preclosure period. Impacts to retrieval from the main drifts based on DBE/BDBEs for the preclosure period

The Potential of User Feedback Through the Iterative Refining of Queries in an Image Retrieval System

NARCIS (Netherlands)

Ben Moussa, Maher; Pasch, Marco; Hiemstra, Djoerd; van der Vet, P.E.; Huibers, Theo W.C.; Marchand-Maillet, Stephane; Bruno, Eric; Nürnberger, Andreas; Detyniecki, Marcin

2007-01-01

Inaccurate or ambiguous expressions in queries lead to poor results in information retrieval. We assume that iterative user feedback can improve the quality of queries. To this end we developed a system for image retrieval that utilizes user feedback to refine the user’s search query. This is done

Tank waste remediation system retrieval and disposal mission waste feed delivery plan

International Nuclear Information System (INIS)

Potter, R.D.

1998-01-01

This document is a plan presenting the objectives, organization, and management and technical approaches for the Waste Feed Delivery (WFD) Program. This WFD Plan focuses on the Tank Waste Remediation System (TWRS) Project's Waste Retrieval and Disposal Mission

Test bed control center design concept for Tank Waste Retrieval Manipulator Systems

International Nuclear Information System (INIS)

Sundstrom, E.; Draper, J.V.; Fausz, A.

1995-01-01

This paper describes the design concept for the control center for the Single Shell Tank Waste Retrieval Manipulator System test bed and the design process behind the concept. The design concept supports all phases of the test bed mission, including technology demonstration, comprehensive system testing, and comparative evaluation for further development and refinement of the TWRMS for field operations

A Database Approach to Content-based XML retrieval

NARCIS (Netherlands)

Hiemstra, Djoerd

2003-01-01

This paper describes a rst prototype system for content-based retrieval from XML data. The system's design supports both XPath queries and complex information retrieval queries based on a language modelling approach to information retrieval. Evaluation using the INEX benchmark shows that it is

High volume tidal or current flow harnessing system

Energy Technology Data Exchange (ETDEWEB)

Gorlov, A.M.

1984-08-07

Apparatus permitting the utilization of large volumes of water in the harnessing and extracting of a portion of the power generated by the rise and fall of ocean tides, ocean currents, or flowing rivers includes the provision of a dam, and a specialized single cavity chamber of limited size as compared with the water head enclosed by the dam, and an extremely high volume gating system in which all or nearly all of the water between the high and low levels on either side of the dam is cyclically gated through the single chamber from one side of the dam to the other so as to alternately provide positive air pressure and a partial vacuum within the single chamber. In one embodiment, the specialized chamber has a barrier at the bottom which divides the bottom of the chamber in half, large ports at the bottom of the chamber to permit inflow and outflow of high volumes of water, and ganged structures having a higher total area than that of corresponding ports, in which the structures form sluice gates to selectively seal off and open different sets of ports. In another embodiment, a single chamber is used without a barrier. In this embodiment, vertical sluice gates are used which may be activated automatically by pressures acting on the sluice gates as a result of ingested and expelled water.

An introduction to the Marshall information retrieval and display system

Science.gov (United States)

1974-01-01

An on-line terminal oriented data storage and retrieval system is presented which allows a user to extract and process information from stored data bases. The use of on-line terminals for extracting and displaying data from the data bases provides a fast and responsive method for obtaining needed information. The system consists of general purpose computer programs that provide the overall capabilities of the total system. The system can process any number of data files via a Dictionary (one for each file) which describes the data format to the system. New files may be added to the system at any time, and reprogramming is not required. Illustrations of the system are shown, and sample inquiries and responses are given.

Millennial Undergraduate Research Strategies in Web and Library Information Retrieval Systems

Science.gov (United States)

Porter, Brandi

2011-01-01

This article summarizes the author's dissertation regarding search strategies of millennial undergraduate students in Web and library online information retrieval systems. Millennials bring a unique set of search characteristics and strategies to their research since they have never known a world without the Web. Through the use of search engines,…

Delve: A Data Set Retrieval and Document Analysis System

KAUST Repository

Akujuobi, Uchenna Thankgod; Zhang, Xiangliang

2017-01-01

Academic search engines (e.g., Google scholar or Microsoft academic) provide a medium for retrieving various information on scholarly documents. However, most of these popular scholarly search engines overlook the area of data set retrieval, which

Design and development of semantic web-based system for computer science domain-specific information retrieval

Directory of Open Access Journals (Sweden)

Ritika Bansal

2016-09-01

Full Text Available In semantic web-based system, the concept of ontology is used to search results by contextual meaning of input query instead of keyword matching. From the research literature, there seems to be a need for a tool which can provide an easy interface for complex queries in natural language that can retrieve the domain-specific information from the ontology. This research paper proposes an IRSCSD system (Information retrieval system for computer science domain as a solution. This system offers advanced querying and browsing of structured data with search results automatically aggregated and rendered directly in a consistent user-interface, thus reducing the manual effort of users. So, the main objective of this research is design and development of semantic web-based system for integrating ontology towards domain-specific retrieval support. Methodology followed is a piecemeal research which involves the following stages. First Stage involves the designing of framework for semantic web-based system. Second stage builds the prototype for the framework using Protégé tool. Third Stage deals with the natural language query conversion into SPARQL query language using Python-based QUEPY framework. Fourth Stage involves firing of converted SPARQL queries to the ontology through Apache's Jena API to fetch the results. Lastly, evaluation of the prototype has been done in order to ensure its efficiency and usability. Thus, this research paper throws light on framework development for semantic web-based system that assists in efficient retrieval of domain-specific information, natural language query interpretation into semantic web language, creation of domain-specific ontology and its mapping with related ontology. This research paper also provides approaches and metrics for ontology evaluation on prototype ontology developed to study the performance based on accessibility of required domain-related information.

A single-image method of aberration retrieval for imaging systems under partially coherent illumination

International Nuclear Information System (INIS)

Xu, Shuang; Liu, Shiyuan; Zhang, Chuanwei; Wei, Haiqing

2014-01-01

We propose a method for retrieving small lens aberrations in optical imaging systems under partially coherent illumination, which only requires to measure one single defocused image of intensity. By deriving a linear theory of imaging systems, we obtain a generalized formulation of aberration sensitivity in a matrix form, which provides a set of analytic kernels that relate the measured intensity distribution directly to the unknown Zernike coefficients. Sensitivity analysis is performed and test patterns are optimized to ensure well-posedness of the inverse problem. Optical lithography simulations have validated the theoretical derivation and confirmed its simplicity and superior performance in retrieving small lens aberrations. (fast track communication)

An efficient and not polluting bottom ash extraction system

International Nuclear Information System (INIS)

Carrea, A.

1992-01-01

This paper reports that boiler waste water effluent must meet more and more tighter requirements to comply with environmental regulations; sluice water resulting from bottom ash handling is one of the main problems in this context, and many utilities are under effort to maximize the reuse of the sluice water, and, if possible, to meet the aim of zero water discharge from bottom ash handling system. At the same time ash reuse efforts gain strength in order to minimize waste production. One solution to these problems can be found in an innovative Bottom Ash Extraction System (MAC System), marked by the peculiarity to be a continuous dry ash removal; the system has been developed in the last four years by MAGALDI INDUSTRIE SRL in collaboration with ANSALDO Ricerche, the R and D department of ANSALDO, the main Italian Boiler Manufacturer, and is now installed in six ENEL Boilers. The elimination of the water as separation element between the bottom part of the furnace and the outside atmosphere gives advantages mainly from the environmental view point, but a certain improvement in the boiler efficiency has also been demonstrated by the application of the system

Storing Fresh Produce for Fast Retrieval in an Automated Compact Cross-dock System

NARCIS (Netherlands)

Zaerpour, N.; Yu, Y.; de Koster, R.B.M.

2015-01-01

We study temporary storage of fresh produce in a cross-dock center. In order to minimize cooling cost, compact storage systems are used. A major disadvantage of these systems is that additional retrieval time is needed, caused by necessary reshuffles due to the improper storage sequence of unit

Response of the Ubiquitin-Proteasome System to Memory Retrieval After Extended-Access Cocaine or Saline Self-Administration.

Science.gov (United States)

Werner, Craig T; Milovanovic, Mike; Christian, Daniel T; Loweth, Jessica A; Wolf, Marina E

2015-12-01

The ubiquitin-proteasome system (UPS) has been implicated in the retrieval-induced destabilization of cocaine- and fear-related memories in Pavlovian paradigms. However, nothing is known about its role in memory retrieval after self-administration of cocaine, an operant paradigm, or how the length of withdrawal from cocaine may influence retrieval mechanisms. Here, we examined UPS activity after an extended-access cocaine self-administration regimen that leads to withdrawal-dependent incubation of cue-induced cocaine craving. Controls self-administered saline. In initial experiments, memory retrieval was elicited via a cue-induced seeking/retrieval test on withdrawal day (WD) 50-60, when craving has incubated. We found that retrieval of cocaine- and saline-associated memories produced similar increases in polyubiquitinated proteins in the nucleus accumbens (NAc), compared with rats that did not undergo a seeking/retrieval test. Measures of proteasome catalytic activity confirmed similar activation of the UPS after retrieval of saline and cocaine memories. However, in a subsequent experiment in which testing was conducted on WD1, proteasome activity in the NAc was greater after retrieval of cocaine memory than saline memory. Analysis of other brain regions confirmed that effects of cocaine memory retrieval on proteasome activity, relative to saline memory retrieval, depend on withdrawal time. These results, combined with prior studies, suggest that the relationship between UPS activity and memory retrieval depends on training paradigm, brain region, and time elapsed between training and retrieval. The observation that mechanisms underlying cocaine memory retrieval change depending on the age of the memory has implications for development of memory destabilization therapies for cue-induced relapse in cocaine addicts.

Information retrieval implementing and evaluating search engines

CERN Document Server

Büttcher, Stefan; Cormack, Gordon V

2016-01-01

Information retrieval is the foundation for modern search engines. This textbook offers an introduction to the core topics underlying modern search technologies, including algorithms, data structures, indexing, retrieval, and evaluation. The emphasis is on implementation and experimentation; each chapter includes exercises and suggestions for student projects. Wumpus -- a multiuser open-source information retrieval system developed by one of the authors and available online -- provides model implementations and a basis for student work. The modular structure of the book allows instructors to use it in a variety of graduate-level courses, including courses taught from a database systems perspective, traditional information retrieval courses with a focus on IR theory, and courses covering the basics of Web retrieval. In addition to its classroom use, Information Retrieval will be a valuable reference for professionals in computer science, computer engineering, and software engineering.

In Situ Modular Waste Retrieval and Treatment System

International Nuclear Information System (INIS)

Walker, M.S.

1996-10-01

As part of the Comprehensive Environmental Response, Compensation, and Liability Act process from remediation of Waste Area Grouping (WAG 6) at ORNL, a public meeting was held for the Proposed Plan. It was recognized that contaminant releases from WAG 6 posed minimal potential risk to the public and the environment. The US DOE in conjunction with the US EPA and the TDEC agreed to defer remedial action at WAG 6 until higher risk release sites were first remediated. This report presents the results of a conceptual design for an In Situ Modular Retrieval and Treatment System able to excavate, shred, and process buried waste on site, with minimum disturbance and distribution of dust and debris. the system would bring appropriate levels of treatment to the waste then encapsulate and leave it in place. The system would be applicable to areas in which waste was disposed in long trenches

Information retrieval system with ability of analogical inference using semantic network and function of fuzzification

Energy Technology Data Exchange (ETDEWEB)

Nakamura, K; Iwai, S

1982-01-01

In information retrieval system, it is necessary to grasp user's subject of interest in order to present appropriate documents to the user. In this paper, the authors propose a model of human ability of analogical inference based on association between key words and, using it, construct an information retrieval system in which the computer with the ability learns its user's subject of interest through question-answering with the user. In this system, the association between key words is represented by a semantic network, and a function of fuzzification of input information is introduced in the semantic network to implement the ability of analogical inference based on the association. Finally, the effect of analogical inference on the learning efficiency of the system is investigated. 5 references.

AX Tank Farm waste retrieval alternatives cost estimates

International Nuclear Information System (INIS)

Krieg, S.A.

1998-01-01

This report presents the estimated costs associated with retrieval of the wastes from the four tanks in AX Tank Farm. The engineering cost estimates developed for this report are based on previous cost data prepared for Project W-320 and the HTI 241-C-106 Heel Retrieval System. The costs presented in this report address only the retrieval of the wastes from the four AX Farm tanks. This includes costs for equipment procurement, fabrication, installation, and operation to retrieve the wastes. The costs to modify the existing plant equipment and systems to support the retrieval equipment are also included. The estimates do not include operational costs associated with pumping the waste out of the waste receiver tank (241-AY-102) between AX Farm retrieval campaigns or transportation, processing, and disposal of the retrieved waste

Spent nuclear fuel retrieval system fuel handling development testing. Final report

International Nuclear Information System (INIS)

Jackson, D.R.; Meeuwsen, P.V.

1997-09-01

Fuel handling development testing was performed in support of the Fuel Retrieval System (FRS) Sub-Project, a subtask of the Spent Nuclear Fuel Project at the Hanford Site in Richland, Washington. The FRS will be used to retrieve and repackage K-Basin Spent Nuclear Fuel (SNF) currently stored in old K-Plant storage basins. The FRS is required to retrieve full fuel canisters from the basin, clean the fuel elements inside the canister to remove excessive uranium corrosion products (or sludge), remove the contents from the canisters and sort the resulting debris, scrap, and fuel for repackaging. The fuel elements and scrap will be collected in fuel storage and scrap baskets in preparation for loading into a multi canister overpack (MCO), while the debris is loaded into a debris bin and disposed of as solid waste. This report describes fuel handling development testing performed from May 1, 1997 through the end of August 1997. Testing during this period was mainly focused on performance of a Schilling Robotic Systems' Conan manipulator used to simulate a custom designed version, labeled Konan, being fabricated for K-Basin deployment. In addition to the manipulator, the camera viewing system, process table layout, and fuel handling processes were evaluated. The Conan test manipulator was installed and fully functional for testing in early 1997. Formal testing began May 1. The purposes of fuel handling development testing were to provide proof of concept and criteria, optimize equipment layout, initialize the process definition, and identify special needs/tools and required design changes to support development of the performance specification. The test program was set up to accomplish these objectives through cold (non-radiological) development testing using simulated and prototype equipment

Interim report spent nuclear fuel retrieval system fuel handling development testing

Energy Technology Data Exchange (ETDEWEB)

Ketner, G.L.; Meeuwsen, P.V.; Potter, J.D.; Smalley, J.T.; Baker, C.P.; Jaquish, W.R.

1997-06-01

Fuel handling development testing was performed in support of the Fuel Retrieval System (FRS) Sub-Project at the Hanford Site. The project will retrieve spent nuclear fuel, clean and remove fuel from canisters, repackage fuel into baskets, and load fuel into a multi-canister overpack (MCO) for vacuum drying and interim dry storage. The FRS is required to retrieve basin fuel canisters, clean fuel elements sufficiently of uranium corrosion products (or sludge), empty fuel from canisters, sort debris and scrap from whole elements, and repackage fuel in baskets in preparation for MCO loading. The purpose of fuel handling development testing was to examine the systems ability to accomplish mission activities, optimization of equipment layouts for initial process definition, identification of special needs/tools, verification of required design changes to support performance specification development, and validation of estimated activity times/throughput. The test program was set up to accomplish this purpose through cold development testing using simulated and prototype equipment; cold demonstration testing using vendor expertise and systems; and graphical computer modeling to confirm feasibility and throughput. To test the fuel handling process, a test mockup that represented the process table was fabricated and installed. The test mockup included a Schilling HV series manipulator that was prototypic of the Schilling Hydra manipulator. The process table mockup included the tipping station, sorting area, disassembly and inspection zones, fuel staging areas, and basket loading stations. The test results clearly indicate that the Schilling Hydra arm cannot effectively perform the fuel handling tasks required unless it is attached to some device that can impart vertical translation, azimuth rotation, and X-Y translation. Other test results indicate the importance of camera locations and capabilities, and of the jaw and end effector tool design. 5 refs., 35 figs., 3 tabs.

Rapid storage and retrieval of genomic intervals from a relational database system using nested containment lists.

Science.gov (United States)

Wiley, Laura K; Sivley, R Michael; Bush, William S

2013-01-01

Efficient storage and retrieval of genomic annotations based on range intervals is necessary, given the amount of data produced by next-generation sequencing studies. The indexing strategies of relational database systems (such as MySQL) greatly inhibit their use in genomic annotation tasks. This has led to the development of stand-alone applications that are dependent on flat-file libraries. In this work, we introduce MyNCList, an implementation of the NCList data structure within a MySQL database. MyNCList enables the storage, update and rapid retrieval of genomic annotations from the convenience of a relational database system. Range-based annotations of 1 million variants are retrieved in under a minute, making this approach feasible for whole-genome annotation tasks. Database URL: https://github.com/bushlab/mynclist.

Eastern Michigan University's Automated Storage and Retrieval System: 10 Years Later

Science.gov (United States)

Bullard, Rita; Wrosch, Jackie

2009-01-01

Automated storage/retrieval systems (ASRSs) are playing an integral part in today's library operations and collections management. Eastern Michigan University installed an ASRS as part of the new Halle Library, which opened in May 1998, to provide "storage" for up to 800,000 items. Over the past 10 years our policies and procedures have…

Project Specific Quality Assurance Plan Project (QAPP) W-211 Initial Tank Retrieval Systems (ITRS)

International Nuclear Information System (INIS)

HALL, L.R.

2000-01-01

This Quality Assurance Program Plan (QAPP) provides information on how the Project Hanford Quality Assurance Program is implemented by CH2M HILL Hanford Group Inc (CHG) for managing the Initial Tank Retrieval Systems (ITRS), Project W-211. This QAPP is responsive to the CHG Quality Assurance Program Description (QAPD) (LMH-MP-599) which provides direction for compliance to 10 CFR 830 120, ''Nuclear Safety Management, Quality Assurance Requirements'', and DOE Order 5700 6C, ''Quality Assurance'' Project W-211 modifies existing facilities and provides systems for retrieval of radioactive wastes from selected double-shell tanks (DST). The contents of these tanks are a combination of supernatant liquids and settled solids. To retrieve waste from the tanks, it is first necessary to mix the liquid and solids prior to transferring the slurry to alternative storage or treatment facilities. The ITRS will provide systems to mobilize the settled solids and transfer the wastes out of the tanks. In so doing, ITRS provides feed for future processing plants, allows for consolidation of tank solids to manage space within existing DST storage capacity, and supports continued safe storage of tank waste. This project includes the design, procurement, construction, startup and turnover of these retrieval systems This QAPP identifies organizational structures and responsibilities. Implementing procedures used by CHG project management can be found in the CHG Quality Assurance Program (CHG QAP) Implementation Matrix located in HNF-IP-0842, Volume XI, Attachment Proposed verification and inspection activities for critical items within the scope of project W-211 are identified in Attachment 1 W-211. Project participants will identify the implementing procedures used by their organization within their QAF'Ps. This project specific QAPP is used to identify requirements in addition to the QAPD and provide, by reference, additional information to other project documents

Construction Method Study For Installation Of A Large Riser In A Single-Shell Tank

International Nuclear Information System (INIS)

Adkisson, D.A.

2010-01-01

This study evaluates and identifies a construction method for cutting a hole in a single-shell tank dome. This study also identifies and evaluates vendors for performing the cut. Single-shell tanks (SST) in the 241-C tank farm are currently being retrieved using various retrieval technologies (e.g., modified sluicing). The Hanford Federal Facility Agreement and Consent Order require that the SSTs be retrieved to less than 360 cubic feet of radioactive waste. The current technologies identified and deployed for tank retrieval have not been able to retrieve waste in accordance with the Hanford Federal Facility Agreement and Consent Order. As such, alternative retrieval systems have been proposed and are currently under construction that will have the ability to retrieve waste to this defined level. The proposed retrieval systems will not fit down existing risers. New risers will need to be installed to provide the retrieval systems access to the inside of the SSTs. The purpose of this study is two-fold. The first objective is to identify multiple concrete cutting technologies and perform an initial pre-screening, evaluate the technologies identified for more in-depth analysis, and recommend a technology/methodology for cutting a hole in the tank dome. The identified/pre-screened methods will be evaluated based on the following criteria: (1) Maturity/complexity; (2) Waste generation; (3) Safety; (4) Cost; and (5) Schedule. Once the preferred method is identified to cut the hole in the tank dome, the second objective is to identify, evaluate, and recommend a vendor for the technology selected that will perform the cutting process.

Functional imaging of the semantic system: retrieval of sensory-experienced and verbally learned knowledge.

Science.gov (United States)

Noppeney, Uta; Price, Cathy J

2003-01-01

This paper considers how functional neuro-imaging can be used to investigate the organization of the semantic system and the limitations associated with this technique. The majority of the functional imaging studies of the semantic system have looked for divisions by varying stimulus category. These studies have led to divergent results and no clear anatomical hypotheses have emerged to account for the dissociations seen in behavioral studies. Only a few functional imaging studies have used task as a variable to differentiate the neural correlates of semantic features more directly. We extend these findings by presenting a new study that contrasts tasks that differentially weight sensory (color and taste) and verbally learned (origin) semantic features. Irrespective of the type of semantic feature retrieved, a common semantic system was activated as demonstrated in many previous studies. In addition, the retrieval of verbally learned, but not sensory-experienced, features enhanced activation in medial and lateral posterior parietal areas. We attribute these "verbally learned" effects to differences in retrieval strategy and conclude that evidence for segregation of semantic features at an anatomical level remains weak. We believe that functional imaging has the potential to increase our understanding of the neuronal infrastructure that sustains semantic processing but progress may require multiple experiments until a consistent explanatory framework emerges.

Information content and sensitivity of the 3β + 2α lidar measurement system for aerosol microphysical retrievals

Science.gov (United States)

Burton, Sharon P.; Chemyakin, Eduard; Liu, Xu; Knobelspiesse, Kirk; Stamnes, Snorre; Sawamura, Patricia; Moore, Richard H.; Hostetler, Chris A.; Ferrare, Richard A.

2016-11-01

There is considerable interest in retrieving profiles of aerosol effective radius, total number concentration, and complex refractive index from lidar measurements of extinction and backscatter at several wavelengths. The combination of three backscatter channels plus two extinction channels (3β + 2α) is particularly important since it is believed to be the minimum configuration necessary for the retrieval of aerosol microphysical properties and because the technological readiness of lidar systems permits this configuration on both an airborne and future spaceborne instrument. The second-generation NASA Langley airborne High Spectral Resolution Lidar (HSRL-2) has been making 3β + 2α measurements since 2012. The planned NASA Aerosol/Clouds/Ecosystems (ACE) satellite mission also recommends the 3β + 2α combination.Here we develop a deeper understanding of the information content and sensitivities of the 3β + 2α system in terms of aerosol microphysical parameters of interest. We use a retrieval-free methodology to determine the basic sensitivities of the measurements independent of retrieval assumptions and constraints. We calculate information content and uncertainty metrics using tools borrowed from the optimal estimation methodology based on Bayes' theorem, using a simplified forward model look-up table, with no explicit inversion. The forward model is simplified to represent spherical particles, monomodal log-normal size distributions, and wavelength-independent refractive indices. Since we only use the forward model with no retrieval, the given simplified aerosol scenario is applicable as a best case for all existing retrievals in the absence of additional constraints. Retrieval-dependent errors due to mismatch between retrieval assumptions and true atmospheric aerosols are not included in this sensitivity study, and neither are retrieval errors that may be introduced in the inversion process. The choice of a simplified model adds clarity to the

Project W-320, 241-C-106 sluicing electrical calculations, Volume 2

International Nuclear Information System (INIS)

Bailey, J.W.

1998-01-01

This supporting document has been prepared to make the FDNW calculations for Project W-320, readily retrievable. These calculations are required: To determine the power requirements needed to power electrical heat tracing segments contained within three manufactured insulated tubing assemblies; To verify thermal adequacy of tubing assembly selection by others; To size the heat tracing feeder and branch circuit conductors and conduits; To size protective circuit breaker and fuses; and To accomplish thermal design for two electrical heat tracing segments: One at C-106 tank riser 7 (CCTV) and one at the exhaust hatchway (condensate drain). Contents include: C-Farm electrical heat tracing; Cable ampacity, lighting, conduit fill and voltage drop; and Control circuit sizing and voltage drop analysis for the seismic shutdown system

Introduction to information retrieval

CERN Document Server

Manning, Christopher D; Schütze, Hinrich

2008-01-01

Class-tested and coherent, this textbook teaches classical and web information retrieval, including web search and the related areas of text classification and text clustering from basic concepts. It gives an up-to-date treatment of all aspects of the design and implementation of systems for gathering, indexing, and searching documents; methods for evaluating systems; and an introduction to the use of machine learning methods on text collections. All the important ideas are explained using examples and figures, making it perfect for introductory courses in information retrieval for advanced un

Diversification in an image retrieval system based on text and image processing

Directory of Open Access Journals (Sweden)

Adrian Iftene

2014-11-01

Full Text Available In this paper we present an image retrieval system created within the research project MUCKE (Multimedia and User Credibility Knowledge Extraction, a CHIST-ERA research project where UAIC{\\footnote{"Alexandru Ioan Cuza" University of Iasi}} is one of the partners{\\footnote{Together with Technical University from Wienna, Austria, CEA-LIST Institute from Paris, France and BILKENT University from Ankara, Turkey}}. Our discussion in this work will focus mainly on components that are part of our image retrieval system proposed in MUCKE, and we present the work done by the UAIC group. MUCKE incorporates modules for processing multimedia content in different modes and languages (like English, French, German and Romanian and UAIC is responsible with text processing tasks (for Romanian and English. One of the problems addressed by our work is related to search results diversification. In order to solve this problem, we first process the user queries in both languages and secondly, we create clusters of similar images.

A novel architecture for information retrieval system based on semantic web

Science.gov (United States)

Zhang, Hui

2011-12-01

Nowadays, the web has enabled an explosive growth of information sharing (there are currently over 4 billion pages covering most areas of human endeavor) so that the web has faced a new challenge of information overhead. The challenge that is now before us is not only to help people locating relevant information precisely but also to access and aggregate a variety of information from different resources automatically. Current web document are in human-oriented formats and they are suitable for the presentation, but machines cannot understand the meaning of document. To address this issue, Berners-Lee proposed a concept of semantic web. With semantic web technology, web information can be understood and processed by machine. It provides new possibilities for automatic web information processing. A main problem of semantic web information retrieval is that when these is not enough knowledge to such information retrieval system, the system will return to a large of no sense result to uses due to a huge amount of information results. In this paper, we present the architecture of information based on semantic web. In addiction, our systems employ the inference Engine to check whether the query should pose to Keyword-based Search Engine or should pose to the Semantic Search Engine.

46 CFR 520.6 - Retrieval of information.

Science.gov (United States)

2010-10-01

... 46 Shipping 9 2010-10-01 2010-10-01 false Retrieval of information. 520.6 Section 520.6 Shipping FEDERAL MARITIME COMMISSION REGULATIONS AFFECTING OCEAN SHIPPING IN FOREIGN COMMERCE CARRIER AUTOMATED TARIFFS § 520.6 Retrieval of information. (a) General. Tariffs systems shall present retrievers with the...

Image Information Retrieval: An Overview of Current Research

OpenAIRE

Abby A. Goodrum

2000-01-01

This paper provides an overview of current research in image information retrieval and provides an outline of areas for future research. The approach is broad and interdisciplinary and focuses on three aspects of image research (IR): text-based retrieval, content-based retrieval, and user interactions with image information retrieval systems. The review concludes with a call for image retrieval evaluation studies similar to TREC.

Data retrieval techniques for nuclear power plants

International Nuclear Information System (INIS)

Sozzi, G.L.; Dahl, C.C.; Gross, R.S.; Voeller, J.G. III

1995-01-01

Data retrieval, processing retrieved data, and maintaining the plant documentation system to reflect the as-built condition of the plant are challenging tasks for most existing nuclear facilities. The information management systems available when these facilities were designed and constructed are archaic by today's standards. Today's plant documentation systems generally include hard copy drawings and text, drawings in various CAD formats, handwritten information, and incompatible databases. These existing plant documentation systems perpetuate inefficiency for the plant technical staff in the performance of their daily activities. This paper discusses data retrieval techniques and tools available to nuclear facilities to minimize the impacts of the existing plant documentation system on plant technical staff productivity

Construction of a bibliographic information database and development of retrieval system for research reports in nuclear science and technology (II)

International Nuclear Information System (INIS)

Han, Duk Haeng; Kim, Tae Whan; Choi, Kwang; Yoo, An Na; Keum, Jong Yong; Kim, In Kwon

1996-05-01

The major goal of this project is to construct a bibliographic information database in nuclear engineering and to develop a prototype retrieval system. To give an easy access to microfiche research report, this project has accomplished the construction of microfiche research reports database and the development of retrieval system. The results of the project are as follows; 1. Microfiche research reports database was constructed by downloading from DOE Energy, NTIS, INIS. 2. The retrieval system was developed in host and web version using access point such as title, abstracts, keyword, report number. 6 tabs., 8 figs., 11 refs. (Author) .new

Construction of a bibliographic information database and development of retrieval system for research reports in nuclear science and technology (II)

Energy Technology Data Exchange (ETDEWEB)

Han, Duk Haeng; Kim, Tae Whan; Choi, Kwang; Yoo, An Na; Keum, Jong Yong; Kim, In Kwon [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1996-05-01

The major goal of this project is to construct a bibliographic information database in nuclear engineering and to develop a prototype retrieval system. To give an easy access to microfiche research report, this project has accomplished the construction of microfiche research reports database and the development of retrieval system. The results of the project are as follows; 1. Microfiche research reports database was constructed by downloading from DOE Energy, NTIS, INIS. 2. The retrieval system was developed in host and web version using access point such as title, abstracts, keyword, report number. 6 tabs., 8 figs., 11 refs. (Author) .new.

Tank waste remediation system retrieval and disposal mission key enabling assumptions

International Nuclear Information System (INIS)

Baldwin, J.H.

1998-01-01

An overall systems approach has been applied to develop action plans to support the retrieval and immobilization waste disposal mission. The review concluded that the systems and infrastructure required to support the mission are known. Required systems are either in place or plans have been developed to ensure they exist when needed. The review showed that since October 1996 a robust system engineering approach to establishing integrated Technical Baselines, work breakdown structures, tank farm structure and configurations and work scope and costs has been established itself as part of the culture within TWRS. An analysis of the programmatic, management and technical activities necessary to declare readiness to proceed with execution of the mission demonstrates that the system, people and hardware will be on line and ready to support the private contractors. The systems approach included defining the retrieval and immobilized waste disposal mission requirements and evaluating the readiness of the TWRS contractor to supply waste feed to the private contractors in June 2OO2. The Phase 1 feed delivery requirements from the Private Contractor Request for Proposals were reviewed. Transfer piping routes were mapped out, existing systems were evaluated, and upgrade requirements were defined. Technical Basis Reviews were completed to define work scope in greater detail, cost estimates and associated year by year financial analyses were completed. TWRS personnel training, qualifications, management systems and procedures were reviewed and shown to be in place and ready to support the Phase 1B mission. Key assumptions and risks that could negatively impact mission success were evaluated and appropriate mitigative actions plans were planned and scheduled

LUNARINFO:A Data Archiving and Retrieving System for the Circumlunar Explorer Based on XML/Web Services

Institute of Scientific and Technical Information of China (English)

ZUO Wei; LI Chunlai; OUYANG Ziyuan; LIU Jianjun; XU Tao

2004-01-01

It is essential to build a modem information management system to store and manage data of our circumlunar explorer in order to realize the scientific objectives. It is difficult for an information system based on traditional distributed technology to communicate information and work together among heterogeneous systems in order to meet the new requirement of Intemet development. XML and Web Services, because of their open standards and self-containing properties, have changed the mode of information organization and data management. Now they can provide a good solution for building an open, extendable, and compatible information management system, and facilitate interchanging and transferring of data among heterogeneous systems. On the basis of the three-tiered browse/server architectures and the Oracle 9i Database as an information storage platform, we have designed and implemented a data archiving and retrieval system for the circumlunar explorer-LUNARINFO. We have also successfully realized the integration between LUNARINFO and the cosmic dust database system. LUNARINFO consists of five function modules for data management, information publishing, system management, data retrieval, and interface integration. Based on XML and Web Services, it not only is an information database system for archiving, long-term storing, retrieving and publication of lunar reference data related to the circumlunar explorer, but also provides data web Services which can be easily developed by various expert groups and connected to the common information system to realize data resource integration.

Human Information Behaviour and Design, Development and Evaluation of Information Retrieval Systems

Science.gov (United States)

Keshavarz, Hamid

2008-01-01

Purpose: The purpose of this paper is to introduce the concept of human information behaviour and to explore the relationship between information behaviour of users and the existing approaches dominating design and evaluation of information retrieval (IR) systems and also to describe briefly new design and evaluation methods in which extensive…

Retrieval system of nuclear data for transmutation of nuclear materials

Energy Technology Data Exchange (ETDEWEB)

Fujita, Mitsutane; Utsumi, Misako; Noda, Tetsuji [National Research Inst. for Metals, Tsukuba, Ibaraki (Japan)

1997-03-01

A database storing the data on nuclear reaction was built to calculate for simulating transmutation behaviours of materials /1/-/3/. In order to retrieve and maintain the database, the user interface for the data retrieval was developed where special knowledge on handling of the database or the machine structure is not required for end-user. It is indicated that using the database, the possibility of He formation and radioactivity in a material can be easily retrieved though the evaluation is qualitatively. (author)

Information storage and retrieval system at Westinghouse Hanford Company Hanford Engineering Development Laboratory (HEDL)

International Nuclear Information System (INIS)

Theo, M.G.

1977-01-01

The information storage and retrieval system developed at Westinghouse--Hanford is described. It will be able to store over two million documents on line. The system uses an interactive minicomputer to search for keyworded documents. Documents of interest can be displayed on CRTs or printed on microfilm reader--printers. 31 figures

Sensitivity Analysis for Atmospheric Infrared Sounder (AIRS) CO2 Retrieval

Science.gov (United States)

Gat, Ilana

2012-01-01

The Atmospheric Infrared Sounder (AIRS) is a thermal infrared sensor able to retrieve the daily atmospheric state globally for clear as well as partially cloudy field-of-views. The AIRS spectrometer has 2378 channels sensing from 15.4 micrometers to 3.7 micrometers, of which a small subset in the 15 micrometers region has been selected, to date, for CO2 retrieval. To improve upon the current retrieval method, we extended the retrieval calculations to include a prior estimate component and developed a channel ranking system to optimize the channels and number of channels used. The channel ranking system uses a mathematical formalism to rapidly process and assess the retrieval potential of large numbers of channels. Implementing this system, we identifed a larger optimized subset of AIRS channels that can decrease retrieval errors and minimize the overall sensitivity to other iridescent contributors, such as water vapor, ozone, and atmospheric temperature. This methodology selects channels globally by accounting for the latitudinal, longitudinal, and seasonal dependencies of the subset. The new methodology increases accuracy in AIRS CO2 as well as other retrievals and enables the extension of retrieved CO2 vertical profiles to altitudes ranging from the lower troposphere to upper stratosphere. The extended retrieval method for CO2 vertical profile estimation using a maximum-likelihood estimation method. We use model data to demonstrate the beneficial impact of the extended retrieval method using the new channel ranking system on CO2 retrieval.

Application of object modeling technique to medical image retrieval system

International Nuclear Information System (INIS)

Teshima, Fumiaki; Abe, Takeshi

1993-01-01

This report describes the results of discussions on the object-oriented analysis methodology, which is one of the object-oriented paradigms. In particular, we considered application of the object modeling technique (OMT) to the analysis of a medical image retrieval system. The object-oriented methodology places emphasis on the construction of an abstract model from real-world entities. The effectiveness of and future improvements to OMT are discussed from the standpoint of the system's expandability. These discussions have elucidated that the methodology is sufficiently well-organized and practical to be applied to commercial products, provided that it is applied to the appropriate problem domain. (author)

Combining semantic technologies with a content-based image retrieval system - Preliminary considerations

Science.gov (United States)

Chmiel, P.; Ganzha, M.; Jaworska, T.; Paprzycki, M.

2017-10-01

Nowadays, as a part of systematic growth of volume, and variety, of information that can be found on the Internet, we observe also dramatic increase in sizes of available image collections. There are many ways to help users browsing / selecting images of interest. One of popular approaches are Content-Based Image Retrieval (CBIR) systems, which allow users to search for images that match their interests, expressed in the form of images (query by example). However, we believe that image search and retrieval could take advantage of semantic technologies. We have decided to test this hypothesis. Specifically, on the basis of knowledge captured in the CBIR, we have developed a domain ontology of residential real estate (detached houses, in particular). This allows us to semantically represent each image (and its constitutive architectural elements) represented within the CBIR. The proposed ontology was extended to capture not only the elements resulting from image segmentation, but also "spatial relations" between them. As a result, a new approach to querying the image database (semantic querying) has materialized, thus extending capabilities of the developed system.

Guenter Tulip Filter Retrieval Experience: Predictors of Successful Retrieval

International Nuclear Information System (INIS)

Turba, Ulku Cenk; Arslan, Bulent; Meuse, Michael; Sabri, Saher; Macik, Barbara Gail; Hagspiel, Klaus D.; Matsumoto, Alan H.; Angle, John F.

2010-01-01

We report our experience with Guenter Tulip filter placement indications, retrievals, and procedural problems, with emphasis on alternative retrieval techniques. We have identified 92 consecutive patients in whom a Guenter Tulip filter was placed and filter removal attempted. We recorded patient demographic information, filter placement and retrieval indications, procedures, standard and nonstandard filter retrieval techniques, complications, and clinical outcomes. The mean time to retrieval for those who experienced filter strut penetration was statistically significant [F(1,90) = 8.55, p = 0.004]. Filter strut(s) IVC penetration and successful retrieval were found to be statistically significant (p = 0.043). The filter hook-IVC relationship correlated with successful retrieval. A modified guidewire loop technique was applied in 8 of 10 cases where the hook appeared to penetrate the IVC wall and could not be engaged with a loop snare catheter, providing additional technical success in 6 of 8 (75%). Therefore, the total filter retrieval success increased from 88 to 95%. In conclusion, the Guenter Tulip filter has high successful retrieval rates with low rates of complication. Additional maneuvers such as a guidewire loop method can be used to improve retrieval success rates when the filter hook is endothelialized.

Basis for Selection of a Residual Waste Retrieval System for Gunite and Associated Tank W-9 at the Oak Ridge National Laboratory

Energy Technology Data Exchange (ETDEWEB)

Lewis, B.E

2000-10-23

Waste retrieval and transfer operations at the Gunite{trademark} and Associated Tanks (GAATs) Remediation Project have been successfully accomplished using the Tank Waste Retrieval System. This system is composed of the Modified Light-Duty Utility Arm, Houdini Vehicle, Waste Dislodging and Conveyance System, Hose Management Arm, and Sludge Conditioning System. GAAT W-9 has been used as a waste-consolidation and batch-transfer tank during the retrieval of sludges and supernatants from the seven Gunite tanks in the North and South tank farms at Oak Ridge National Laboratory. Tank W-9 was used as a staging tank for the transfers to the Melton Valley Storage Tanks (MVSTs). A total of 18 waste transfers from W-9 occurred between May 25, 1999, and March 30, 2000. Most of these transfers were accomplished using the PulsAir Mixer to mobilize and mix the slurry and a submersible retrieval-transfer pump to transfer the slurry through the Sludge Conditioning System and the {approx}1-mile long, 2-in.-diam waste-transfer line to the MVSTs. The transfers from W-9 have consisted of low-solids-content slurries with solids contents ranging from {approx}2.8 to 6.8 mg/L. Of the initial {approx}88,000 gal of wet sludge estimated in the GAATs, a total of {approx}60,451 gal have been transferred to the MVSTs via tank W-9 as of March 30, 2000. Once the waste-consolidation operations and transfers from W-9 to the MVSTs are completed, the remaining material in W-9 will be mobilized and transferred to the active waste system, Bethel Valley Evaporator Service Tank W-23. Tank W-23 will serve as a batch tank for the final waste transfers from tank W-9 to the MVSTs. This report provides a summary of the requirements and recommendations for the final waste retrieval system for tank W-9, a compilation of the sample analysis data for the sludge in W-9, and brief descriptions of the various waste-retrieval system concepts that were considered for this task. The recommended residual waste retrieval

Retrievability in the Belgian deep disposal concept in clay

International Nuclear Information System (INIS)

Preter, P. de

2000-01-01

While radioactive waste disposal implies that there is no intention to retrieve the waste, retrievability refers to the potential to retrieve the waste. So, retrievability can be an integrated element of a disposal solution. The different reasons for considering retrievability in the development of a disposal solution are discussed. Amongst them, the precautionary principle takes an important place. The development of a disposal solution should be in the first place safety-driven. The use of robust, high-integrity waste containers or overpacks contributes directly to safety, but also to the enhancement of the retrievability. Indeed, as long as the first barrier is intact, safe waste retrieval is in principle possible. By extending the period of easy access to the waste, i.e. by keeping the repository open during a longer period than needed for waste disposal operations, safety and retrievability goals can become contradictory. Indefinitely postponing the decision to close the repository enhances the risk of unforeseen perturbations of the disposal system and the risk of abandonment. This pleads of course for limiting the duration of the open phase to a reasonable period of time. Otherwise, the advantage of a prolonged open repository, as a means to prolong retrievability of the waste, is cancelled by the increasing risks of a system whose safety relies on societal, political and decisional stability, and not on a robust, passive multi-barrier system. (author)

Automated information retrieval using CLIPS

Science.gov (United States)

Raines, Rodney Doyle, III; Beug, James Lewis

1991-01-01

Expert systems have considerable potential to assist computer users in managing the large volume of information available to them. One possible use of an expert system is to model the information retrieval interests of a human user and then make recommendations to the user as to articles of interest. At Cal Poly, a prototype expert system written in the C Language Integrated Production System (CLIPS) serves as an Automated Information Retrieval System (AIRS). AIRS monitors a user's reading preferences, develops a profile of the user, and then evaluates items returned from the information base. When prompted by the user, AIRS returns a list of items of interest to the user. In order to minimize the impact on system resources, AIRS is designed to run in the background during periods of light system use.

Project W-320, 241-C-106 sluicing supporting documentation bibliography

International Nuclear Information System (INIS)

Bailey, J.W.

1998-01-01

This supporting document has been prepared to make the listing of documentation used to develop, or in support of Project W-320, readily retrievable. All documents are sorted by document number and list the document type. Tank 241-C-106 has been included on the High Heat Load Watch List

EM-21 Retrieval Knowledge Center: Waste Retrieval Challenges

Energy Technology Data Exchange (ETDEWEB)

Fellinger, Andrew P.; Rinker, Michael W.; Berglin, Eric J.; Minichan, Richard L.; Poirier, Micheal R.; Gauglitz, Phillip A.; Martin, Bruce A.; Hatchell, Brian K.; Saldivar, Eloy; Mullen, O Dennis; Chapman, Noel F.; Wells, Beric E.; Gibbons, Peter W.

2009-04-10

EM-21 is the Waste Processing Division of the Office of Engineering and Technology, within the U.S. Department of Energy’s (DOE) Office of Environmental Management (EM). In August of 2008, EM-21 began an initiative to develop a Retrieval Knowledge Center (RKC) to provide the DOE, high level waste retrieval operators, and technology developers with centralized and focused location to share knowledge and expertise that will be used to address retrieval challenges across the DOE complex. The RKC is also designed to facilitate information sharing across the DOE Waste Site Complex through workshops, and a searchable database of waste retrieval technology information. The database may be used to research effective technology approaches for specific retrieval tasks and to take advantage of the lessons learned from previous operations. It is also expected to be effective for remaining current with state-of-the-art of retrieval technologies and ongoing development within the DOE Complex. To encourage collaboration of DOE sites with waste retrieval issues, the RKC team is co-led by the Savannah River National Laboratory (SRNL) and the Pacific Northwest National Laboratory (PNNL). Two RKC workshops were held in the Fall of 2008. The purpose of these workshops was to define top level waste retrieval functional areas, exchange lessons learned, and develop a path forward to support a strategic business plan focused on technology needs for retrieval. The primary participants involved in these workshops included retrieval personnel and laboratory staff that are associated with Hanford and Savannah River Sites since the majority of remaining DOE waste tanks are located at these sites. This report summarizes and documents the results of the initial RKC workshops. Technology challenges identified from these workshops and presented here are expected to be a key component to defining future RKC-directed tasks designed to facilitate tank waste retrieval solutions.

EM-21 Retrieval Knowledge Center: Waste Retrieval Challenges

International Nuclear Information System (INIS)

Fellinger, Andrew P.; Rinker, Michael W.; Berglin, Eric J.; Minichan, Richard L.; Poirier, Micheal R.; Gauglitz, Phillip A.; Martin, Bruce A.; Hatchell, Brian K.; Saldivar, Eloy; Mullen, O Dennis; Chapman, Noel F.; Wells, Beric E.; Gibbons, Peter W.

2009-01-01

EM-21 is the Waste Processing Division of the Office of Engineering and Technology, within the U.S. Department of Energy's (DOE) Office of Environmental Management (EM). In August of 2008, EM-21 began an initiative to develop a Retrieval Knowledge Center (RKC) to provide the DOE, high level waste retrieval operators, and technology developers with centralized and focused location to share knowledge and expertise that will be used to address retrieval challenges across the DOE complex. The RKC is also designed to facilitate information sharing across the DOE Waste Site Complex through workshops, and a searchable database of waste retrieval technology information. The database may be used to research effective technology approaches for specific retrieval tasks and to take advantage of the lessons learned from previous operations. It is also expected to be effective for remaining current with state-of-the-art of retrieval technologies and ongoing development within the DOE Complex. To encourage collaboration of DOE sites with waste retrieval issues, the RKC team is co-led by the Savannah River National Laboratory (SRNL) and the Pacific Northwest National Laboratory (PNNL). Two RKC workshops were held in the Fall of 2008. The purpose of these workshops was to define top level waste retrieval functional areas, exchange lessons learned, and develop a path forward to support a strategic business plan focused on technology needs for retrieval. The primary participants involved in these workshops included retrieval personnel and laboratory staff that are associated with Hanford and Savannah River Sites since the majority of remaining DOE waste tanks are located at these sites. This report summarizes and documents the results of the initial RKC workshops. Technology challenges identified from these workshops and presented here are expected to be a key component to defining future RKC-directed tasks designed to facilitate tank waste retrieval solutions

Development and evaluation of a geographic information retrieval system using fine grained toponyms

Directory of Open Access Journals (Sweden)

Damien Palacio

2015-12-01

Full Text Available Geographic information retrieval (GIR is concerned with returning information in response to an information need, typically expressed in terms of a thematic and spatial component linked by a spatial relationship. However, evaluation initiatives have often failed to show significant differences between simple text baselines and more complex spatially enabled GIR approaches. We explore the effectiveness of three systems (a text baseline, spatial query expansion, and a full GIR system utilizing both text and spatial indexes at retrieving documents from a corpus describing mountaineering expeditions, centred around fine grained toponyms. To allow evaluation, we use user generated content (UGC in the form of metadata associated with individual articles to build a test collection of queries and judgments. The test collection allowed us to demonstrate that a GIR-based method significantly outperformed a text baseline for all but very specific queries associated with very small query radii. We argue that such approaches to test collection development have much to offer in the evaluation of GIR.

Monitoring system specifications: retrieval of surf from a salt repository

International Nuclear Information System (INIS)

1980-01-01

The task of developing specifications for a reference monitoring system determined by repository environmental conditions, retrieval operations, and federal regulatory criteria is discussed. The monitoring system specified in this report is capable of measuring (1) package position and orientation, (2) vault deformation, (3) brine accumulation, (4) spent fuel dissolution, (5) temperature, (6) nuclear radiation, and (7) package condition with sufficient accuracy to provide data input to a general risk assessment model. In order to define a monitoring system which can provide probabilistic data on radiological risk to operating personnel and the general public for a salt mine repository, the following information is required: (1) a complete design of the salt SURF repository including inventory, density and waste package design details; (2) probalistic failure rate data on containment integrity of the SURF waste package; (3) probabilistic failure rate data on the monitoring system components

Experiments with a novel content-based image retrieval software: can we eliminate classification systems in adolescent idiopathic scoliosis?

Science.gov (United States)

Menon, K Venugopal; Kumar, Dinesh; Thomas, Tessamma

2014-02-01

Study Design Preliminary evaluation of new tool. Objective To ascertain whether the newly developed content-based image retrieval (CBIR) software can be used successfully to retrieve images of similar cases of adolescent idiopathic scoliosis (AIS) from a database to help plan treatment without adhering to a classification scheme. Methods Sixty-two operated cases of AIS were entered into the newly developed CBIR database. Five new cases of different curve patterns were used as query images. The images were fed into the CBIR database that retrieved similar images from the existing cases. These were analyzed by a senior surgeon for conformity to the query image. Results Within the limits of variability set for the query system, all the resultant images conformed to the query image. One case had no similar match in the series. The other four retrieved several images that were matching with the query. No matching case was left out in the series. The postoperative images were then analyzed to check for surgical strategies. Broad guidelines for treatment could be derived from the results. More precise query settings, inclusion of bending films, and a larger database will enhance accurate retrieval and better decision making. Conclusion The CBIR system is an effective tool for accurate documentation and retrieval of scoliosis images. Broad guidelines for surgical strategies can be made from the postoperative images of the existing cases without adhering to any classification scheme.

Hollow Abutment Screw Design for Easy Retrieval in Case of Screw Fracture in Dental Implant System.

Science.gov (United States)

Sim, Bo Kyun; Kim, Bongju; Kim, Min Jeong; Jeong, Guk Hyun; Ju, Kyung Won; Shin, Yoo Jin; Kim, Man Yong; Lee, Jong-Ho

2017-01-01

The prosthetic component of dental implant is attached on the abutment which is connected to the fixture with an abutment screw. The abutment screw fracture is not frequent; however, the retrieval of the fractured screw is not easy, and it poses complications. A retrieval kit was developed which utilizes screw removal drills to make a hole on the fractured screw that provides an engaging drill to unscrew it. To minimize this process, the abutment screw is modified with a prefabricated access hole for easy retrieval. This study aimed to introduce this modified design of the abutment screw, the concept of easy retrieval, and to compare the mechanical strengths of the conventional and hollow abutment screws by finite element analysis (FEA) and mechanical test. In the FEA results, both types of abutment screws showed similar stress distribution in the single artificial tooth system. A maximum load difference of about 2% occurred in the vertical load by a mechanical test. This study showed that the hollow abutment screw may be an alternative to the conventional abutment screws because this is designed for easy retrieval and that both abutment screws showed no significant difference in the mechanical tests and in the FEA.

Video Retrieval Berdasarkan Teks dan Gambar

Directory of Open Access Journals (Sweden)

Rahmi Hidayati

2013-01-01

Abstract Retrieval video has been used to search a video based on the query entered by user which were text and image. This system could increase the searching ability on video browsing and expected to reduce the video’s retrieval time. The research purposes were designing and creating a software application of retrieval video based on the text and image on the video. The index process for the text is tokenizing, filtering (stopword, stemming. The results of stemming to saved in the text index table. Index process for the image is to create an image color histogram and compute the mean and standard deviation at each primary color red, green and blue (RGB of each image. The results of feature extraction is stored in the image table The process of video retrieval using the query text, images or both. To text query system to process the text query by looking at the text index tables. If there is a text query on the index table system will display information of the video according to the text query. To image query system to process the image query by finding the value of the feature extraction means red, green means, means blue, red standard deviation, standard deviation and standard deviation of blue green. If the value of the six features extracted query image on the index table image will display the video information system according to the query image. To query text and query images, the system will display the video information if the query text and query images have a relationship that is query text and query image has the same film title.   Keywords—  video, index, retrieval, text, image

Psychophysical studies of the performance of an image database retrieval system

Science.gov (United States)

Papathomas, Thomas V.; Conway, Tiffany E.; Cox, Ingemar J.; Ghosn, Joumana; Miller, Matt L.; Minka, Thomas P.; Yianilos, Peter N.

1998-07-01

We describe psychophysical experiments conducted to study PicHunter, a content-based image retrieval (CBIR) system. Experiment 1 studies the importance of using (a) semantic information, (2) memory of earlier input and (3) relative, rather than absolute, judgements of image similarity. The target testing paradigm is used in which a user must search for an image identical to a target. We find that the best performance comes from a version of PicHunter that uses only semantic cues, with memory and relative similarity judgements. Second best is use of both pictorial and semantic cues, with memory and relative similarity judgements. Most reports of CBIR systems provide only qualitative measures of performance based on how similar retrieved images are to a target. Experiment 2 puts PicHunter into this context with a more rigorous test. We first establish a baseline for our database by measuring the time required to find an image that is similar to a target when the images are presented in random order. Although PicHunter's performance is measurably better than this, the test is weak because even random presentation of images yields reasonably short search times. This casts doubt on the strength of results given in other reports where no baseline is established.

Tank waste remediation system retrieval and disposal mission readiness-to-proceed guidance and requirements to deliverables crosswalk

International Nuclear Information System (INIS)

Hall, C.E.

1998-01-01

Before RL can authorize proceeding with Phase 1B, the PHMC team must demonstrate its readiness to retrieve and deliver the waste to the private contractors and to receive and dispose of the products and byproducts returned from the treatment. The PHMC team has organized their plans for providing these vitrification-support services into the Retrieval and Disposal Mission within the Tank Waste Remediation System (TWRS) Program

How to average logarithmic retrievals?

Directory of Open Access Journals (Sweden)

B. Funke

2012-04-01

Full Text Available Calculation of mean trace gas contributions from profiles obtained by retrievals of the logarithm of the abundance rather than retrievals of the abundance itself are prone to biases. By means of a system simulator, biases of linear versus logarithmic averaging were evaluated for both maximum likelihood and maximum a priori retrievals, for various signal to noise ratios and atmospheric variabilities. These biases can easily reach ten percent or more. As a rule of thumb we found for maximum likelihood retrievals that linear averaging better represents the true mean value in cases of large local natural variability and high signal to noise ratios, while for small local natural variability logarithmic averaging often is superior. In the case of maximum a posteriori retrievals, the mean is dominated by the a priori information used in the retrievals and the method of averaging is of minor concern. For larger natural variabilities, the appropriateness of the one or the other method of averaging depends on the particular case because the various biasing mechanisms partly compensate in an unpredictable manner. This complication arises mainly because of the fact that in logarithmic retrievals the weight of the prior information depends on abundance of the gas itself. No simple rule was found on which kind of averaging is superior, and instead of suggesting simple recipes we cannot do much more than to create awareness of the traps related with averaging of mixing ratios obtained from logarithmic retrievals.

Experience with new retrieval forceps for foreign body removal in the vascular and urinary systems

International Nuclear Information System (INIS)

Selby, J.B.; Bittner, G.M.; Tegtmeyer, C.J.

1989-01-01

A new type of forceps for foreign-body retrieval has recently become available. It consists of single- or multiple-toothed forceps mounted on a flexible, stainless steel shaft. The authors have used this device successfully three times in the vascular system and seven times in the urinary tract without complications. Foreign bodies removed include a catheter fragment, angiographic guidewire, detachable balloon, stone basket, and various ureteral stents. All the procedures were performed quickly and without difficulty. These forceps have become the authors' first choice in many retrieval situations

The Gunite and Associated Tanks Remediation Project Tank Waste Retrieval Performance and Lessons Learned, vol. 1 [of 2

Energy Technology Data Exchange (ETDEWEB)

Lewis, BE

2003-10-07

The Gunite and Associated Tanks (GAAT) Remediation Project was the first of its kind performed in the United States. Robotics and remotely operated equipment were used to successfully transfer almost 94,000 gal of remote-handled transuranic sludge containing over 81,000 Ci of radioactive contamination from nine large underground storage tanks at the Oak Ridge National Laboratory (ORNL). The sludge was transferred with over 439,000 gal of radioactive waste supernatant and {approx}420,500 gal of fresh water that was used in sluicing operations. The GAATs are located in a high-traffic area of ORNL near a main thoroughfare. A phased and integrated approach to waste retrieval operations was used for the GAAT Remediation Project. The project promoted safety by obtaining experience from low-risk operations in the North Tank Farm before moving to higher-risk operations in the South Tank Farm. This approach allowed project personnel to become familiar with the tanks and waste, as well as the equipment, processes, procedures, and operations required to perform successful waste retrieval. By using an integrated approach to tank waste retrieval and tank waste management, the project was completed years ahead of the original baseline schedule, which resulted in avoiding millions of dollars in associated costs. This report is organized in two volumes. Volume 1 provides information on the various phases of the GAAT Remediation Project. It also describes the different types of equipment and how they were used. The emphasis of Volume 1 is on the description of the tank waste retrieval performance and the lessons learned during the GAAT Remediation Project. Volume 2 provides the appendixes for the report, which include the following information: (A) Background Information for the Gunite and Associated Tanks Operable Unit; (B) Annotated Bibliography; (C) Comprehensive Listing of the Sample Analysis Data from the GAAT Remediation Project; (D) GAAT Equipment Matrix; and (E) Vendor List

Facilitating medical information search using Google Glass connected to a content-based medical image retrieval system.

Science.gov (United States)

Widmer, Antoine; Schaer, Roger; Markonis, Dimitrios; Muller, Henning

2014-01-01

Wearable computing devices are starting to change the way users interact with computers and the Internet. Among them, Google Glass includes a small screen located in front of the right eye, a camera filming in front of the user and a small computing unit. Google Glass has the advantage to provide online services while allowing the user to perform tasks with his/her hands. These augmented glasses uncover many useful applications, also in the medical domain. For example, Google Glass can easily provide video conference between medical doctors to discuss a live case. Using these glasses can also facilitate medical information search by allowing the access of a large amount of annotated medical cases during a consultation in a non-disruptive fashion for medical staff. In this paper, we developed a Google Glass application able to take a photo and send it to a medical image retrieval system along with keywords in order to retrieve similar cases. As a preliminary assessment of the usability of the application, we tested the application under three conditions (images of the skin; printed CT scans and MRI images; and CT and MRI images acquired directly from an LCD screen) to explore whether using Google Glass affects the accuracy of the results returned by the medical image retrieval system. The preliminary results show that despite minor problems due to the relative stability of the Google Glass, images can be sent to and processed by the medical image retrieval system and similar images are returned to the user, potentially helping in the decision making process.

Hazardous waste dislodging and conveyance: The confined sluicing method

International Nuclear Information System (INIS)

Summers, D.A.; Fossey, R.D.; Mann, M.D.; Blaine, J.G.

1994-09-01

This report describes an investigation of a means for dislodging and conveying waste currently stored in underground storage tanks. A series of experiments have been carried out to evaluate the potential of a medium pressure, medium flow rate cutting system as a means of dislodging the waste. It has been found that waterjets at a pressure of 10,000 psi can effectively cut the material which has been chosen to simulate the hardened saltcake within the storage tanks. Based on a parameterization test it has thus been calculated that an inlet flow volume of approximately 30 gallons per minute will be sufficient to excavate 30 gallons per minute of waste from a tank. In order to transport the resulting slurry from the tank, a modified jet pump has been developed and has demonstrated its capability of conveying fluid and waste particles, up to one inch in diameter, to a height of more than 60 feet. Experiments were conducted to examine different configurations to achieve the production levels required for waste removal and to clean the walls of residual material. It was found more effective to clean the walls using an inclined angle of impact rather than a perpendicular angle of impact in order to provide a safeguard against driving the water through any cracks in the containment. It was demonstrated that excavation can take place with almost total immediate extraction of the water and debris from the cutting process. The results have qualitatively shown the potential of a medium pressure waterjet system for achieving the required results for underground storage tank waste retrieval

Wellhead bowl protector and retrieving tool

International Nuclear Information System (INIS)

Young, J.A.

1991-01-01

This patent describes improvement in a wellhead protection system including a wear bushing and a retrieving tool. The improvement comprises a wear bushing supported within the wellhead, wherein the wear bushing includes an enlarged upper end having an external support shoulder for engagement with an internal support shoulder formed in the wellhead; wherein the wear bushing further includes an internal circumferential slot intersected by at least one vertically extending slot, the vertical slot extending from the circumferential slot to the upper end of the wear bushing; a retrieving tool having at least one outwardly biased, retractable lug member mounted thereon; and wherein the retrieving tool includes an enlarged portion adapted to be received within the enlarged upper end of the wear bushing. This patent also describes a method of retrieving a wear bushing from a wellhead comprising the steps of: lowering a retrieving tool into the wellhead for locking engagement with the wear bushing; aligning the retrieving tool with the wear bushing for automatically forcing lug members carried by the retrieving tool outwardly into locking engagement with the wear bushing; monitoring drill string weight for determining engagement of the retrieving tool with the wear bushing, wherein a substantial decrease in drill string weight is an indication that the retrieving tool is engaged with the wear bushing; and removing the wear bushing from the wellhead

Plant leaf chlorophyll content retrieval based on a field imaging spectroscopy system.

Science.gov (United States)

Liu, Bo; Yue, Yue-Min; Li, Ru; Shen, Wen-Jing; Wang, Ke-Lin

2014-10-23

A field imaging spectrometer system (FISS; 380-870 nm and 344 bands) was designed for agriculture applications. In this study, FISS was used to gather spectral information from soybean leaves. The chlorophyll content was retrieved using a multiple linear regression (MLR), partial least squares (PLS) regression and support vector machine (SVM) regression. Our objective was to verify the performance of FISS in a quantitative spectral analysis through the estimation of chlorophyll content and to determine a proper quantitative spectral analysis method for processing FISS data. The results revealed that the derivative reflectance was a more sensitive indicator of chlorophyll content and could extract content information more efficiently than the spectral reflectance, which is more significant for FISS data compared to ASD (analytical spectral devices) data, reducing the corresponding RMSE (root mean squared error) by 3.3%-35.6%. Compared with the spectral features, the regression methods had smaller effects on the retrieval accuracy. A multivariate linear model could be the ideal model to retrieve chlorophyll information with a small number of significant wavelengths used. The smallest RMSE of the chlorophyll content retrieved using FISS data was 0.201 mg/g, a relative reduction of more than 30% compared with the RMSE based on a non-imaging ASD spectrometer, which represents a high estimation accuracy compared with the mean chlorophyll content of the sampled leaves (4.05 mg/g). Our study indicates that FISS could obtain both spectral and spatial detailed information of high quality. Its image-spectrum-in-one merit promotes the good performance of FISS in quantitative spectral analyses, and it can potentially be widely used in the agricultural sector.

Project W-320, 241-C-106 sluicing, master calculation list

International Nuclear Information System (INIS)

Bailey, J.W.

1998-01-01

This supporting document has been prepared to make the Master Calculation List readily retrievable. The list gives the status of the calculation (as-built, not used, applied, etc.), the calculation title, its originator, comments, and report number under which it was issued. Tank 241-C-106 has been included on the High Heat Load Watch List

Retrievable Inferior Vena Cava Filters: Factors that Affect Retrieval Success

Energy Technology Data Exchange (ETDEWEB)

Geisbuesch, Philipp, E-mail: philippgeisbuesch@gmx.de; Benenati, James F.; Pena, Constantino S.; Couvillon, Joseph; Powell, Alex; Gandhi, Ripal; Samuels, Shaun; Uthoff, Heiko [Baptist Cardiac and Vascular Institute, Division of Vascular and Interventional Radiology (United States)

2012-10-15

Purpose: To report and analyze the indications, procedural success, and complications of retrievable inferior vena cava filters (rIVCF) placement and to identify parameters that influence retrieval attempt and failure. Methods: Between January 2005 and December 2010, a total of 200 patients (80 men, median age 67 years, range 11-95 years) received a rIVCF with the clinical possibility that it could be removed. All patients with rIVCF were prospectively entered into a database and followed until retrieval or a decision not to retrieve the filter was made. A retrospective analysis of this database was performed. Results: Sixty-one percent of patients had an accepted indication for filter placement; 39% of patients had a relative indication. There was a tendency toward a higher retrieval rate in patients with relative indications (40% vs. 55%, P = 0.076). Filter placement was technically successful in all patients, with no procedure-related mortality. The retrieval rate was 53%. Patient age of >80 years (odds ratio [OR] 0.056, P > 0.0001) and presence of malignancy (OR 0.303, P = 0.003) was associated with a significantly reduced probability for attempted retrieval. Retrieval failure occurred in 7% (6 of 91) of all retrieval attempts. A time interval of > 90 days between implantation and attempted retrieval was associated with retrieval failure (OR 19.8, P = 0.009). Conclusions: Patient age >80 years and a history of malignancy are predictors of a reduced probability for retrieval attempt. The rate of retrieval failure is low and seems to be associated with a time interval of >90 days between filter placement and retrieval.

Retrievable Inferior Vena Cava Filters: Factors that Affect Retrieval Success

International Nuclear Information System (INIS)

Geisbüsch, Philipp; Benenati, James F.; Peña, Constantino S.; Couvillon, Joseph; Powell, Alex; Gandhi, Ripal; Samuels, Shaun; Uthoff, Heiko

2012-01-01

Purpose: To report and analyze the indications, procedural success, and complications of retrievable inferior vena cava filters (rIVCF) placement and to identify parameters that influence retrieval attempt and failure. Methods: Between January 2005 and December 2010, a total of 200 patients (80 men, median age 67 years, range 11–95 years) received a rIVCF with the clinical possibility that it could be removed. All patients with rIVCF were prospectively entered into a database and followed until retrieval or a decision not to retrieve the filter was made. A retrospective analysis of this database was performed. Results: Sixty-one percent of patients had an accepted indication for filter placement; 39% of patients had a relative indication. There was a tendency toward a higher retrieval rate in patients with relative indications (40% vs. 55%, P = 0.076). Filter placement was technically successful in all patients, with no procedure-related mortality. The retrieval rate was 53%. Patient age of >80 years (odds ratio [OR] 0.056, P > 0.0001) and presence of malignancy (OR 0.303, P = 0.003) was associated with a significantly reduced probability for attempted retrieval. Retrieval failure occurred in 7% (6 of 91) of all retrieval attempts. A time interval of > 90 days between implantation and attempted retrieval was associated with retrieval failure (OR 19.8, P = 0.009). Conclusions: Patient age >80 years and a history of malignancy are predictors of a reduced probability for retrieval attempt. The rate of retrieval failure is low and seems to be associated with a time interval of >90 days between filter placement and retrieval.

Robust retrieval of fine art paintings

Science.gov (United States)

Smolka, Bogdan; Lukac, Rastislav; Plataniotis, Konstantinos N.; Venetsanopoulos, Anastasios N.

2003-10-01

The rapid growth of image archives increases the need for efficient and fast tools that can retrieve and search through large amount of visual data. In this paper we propose an efficient method of extracting the image color content, which serves as an image digital signature, allowing to efficiently index and retrieve the content of large, heterogeneous multimedia databases. We apply the proposed method for the retrieval of images from the WEBMUSEUM Internet database, containing the collection of fine art images and show that the new method of image color representation is robust to image distorsions caused by resizing and compression and can be incorporated into existing retrieval systems which exploit the information on color content in digital images.

Content-based multimedia retrieval: indexing and diversification

NARCIS (Netherlands)

van Leuken, R.H.

2009-01-01

The demand for efficient systems that facilitate searching in multimedia databases and collections is vastly increasing. Application domains include criminology, musicology, trademark registration, medicine and image or video retrieval on the web. This thesis discusses content-based retrieval

Interactive Exploration for Image Retrieval

Directory of Open Access Journals (Sweden)

Jérôme Fournier

2005-08-01

Full Text Available We present a new version of our content-based image retrieval system RETIN. It is based on adaptive quantization of the color space, together with new features aiming at representing the spatial relationship between colors. Color analysis is also extended to texture. Using these powerful indexes, an original interactive retrieval strategy is introduced. The process is based on two steps for handling the retrieval of very large image categories. First, a controlled exploration method of the database is presented. Second, a relevance feedback method based on statistical learning is proposed. All the steps are evaluated by experiments on a generalist database.

Application of a regularized model inversion system (REGFLEC) to multi-temporal RapidEye imagery for retrieving vegetation characteristics

KAUST Repository

Houborg, Rasmus

2015-10-14

Accurate retrieval of canopy biophysical and leaf biochemical constituents from space observations is critical to diagnosing the functioning and condition of vegetation canopies across spatio-temporal scales. Retrieved vegetation characteristics may serve as important inputs to precision farming applications and as constraints in spatially and temporally distributed model simulations of water and carbon exchange processes. However significant challenges remain in the translation of composite remote sensing signals into useful biochemical, physiological or structural quantities and treatment of confounding factors in spectrum-trait relations. Bands in the red-edge spectrum have particular potential for improving the robustness of retrieved vegetation properties. The development of observationally based vegetation retrieval capacities, effectively constrained by the enhanced information content afforded by bands in the red-edge, is a needed investment towards optimizing the benefit of current and future satellite sensor systems. In this study, a REGularized canopy reFLECtance model (REGFLEC) for joint leaf chlorophyll (Chll) and leaf area index (LAI) retrieval is extended to sensor systems with a band in the red-edge region for the first time. Application to time-series of 5 m resolution multi-spectral RapidEye data is demonstrated over an irrigated agricultural region in central Saudi Arabia, showcasing the value of satellite-derived crop information at this fine scale for precision management. Validation against in-situ measurements in fields of alfalfa, Rhodes grass, carrot and maize indicate improved accuracy of retrieved vegetation properties when exploiting red-edge information in the model inversion process. © (2015) COPYRIGHT Society of Photo-Optical Instrumentation Engineers (SPIE).

Functional-anatomic study of episodic retrieval using fMRI. I. Retrieval effort versus retrieval success.

Science.gov (United States)

Buckner, R L; Koutstaal, W; Schacter, D L; Wagner, A D; Rosen, B R

1998-04-01

A number of recent functional imaging studies have identified brain areas activated during tasks involving episodic memory retrieval. The identification of such areas provides a foundation for targeted hypotheses regarding the more specific contributions that these areas make to episodic retrieval. As a beginning effort toward such an endeavor, whole-brain functional magnetic resonance imaging (fMRI) was used to examine 14 subjects during episodic word recognition in a block-designed fMRI experiment. Study conditions were manipulated by presenting either shallow or deep encoding tasks. This manipulation yielded two recognition conditions that differed with regard to retrieval effort and retrieval success: shallow encoding yielded low levels of recognition success with high levels of retrieval effort, and deep encoding yielded high levels of recognition success with low levels of effort. Many brain areas were activated in common by these two recognition conditions compared to a low-level fixation condition, including left and right prefrontal regions often detected during PET episodic retrieval paradigms (e.g., R. L. Buckner et al., 1996, J. Neurosci. 16, 6219-6235) thereby generalizing these findings to fMRI. Characterization of the activated regions in relation to the separate recognition conditions showed (1) bilateral anterior insular regions and a left dorsal prefrontal region were more active after shallow encoding, when retrieval demanded greatest effort, and (2) right anterior prefrontal cortex, which has been implicated in episodic retrieval, was most active during successful retrieval after deep encoding. We discuss these findings in relation to component processes involved in episodic retrieval and in the context of a companion study using event-related fMRI.

Dual Systems for Spatial Updating in Immediate and Retrieved Environments: Evidence from Bias Analysis.

Science.gov (United States)

Liu, Chuanjun; Xiao, Chengli

2018-01-01

The spatial updating and memory systems are employed during updating in both the immediate and retrieved environments. However, these dual systems seem to work differently, as the difference of pointing latency and absolute error between the two systems vary across environments. To verify this issue, the present study employed the bias analysis of signed errors based on the hypothesis that the transformed representation will bias toward the original one. Participants learned a spatial layout and then either stayed in the learning location or were transferred to a neighboring room directly or after being disoriented. After that, they performed spatial judgments from perspectives aligned with the learning direction, aligned with the direction they faced during the test, or a novel direction misaligned with the two above-mentioned directions. The patterns of signed error bias were consistent across environments. Responses for memory aligned perspectives were unbiased, whereas responses for sensorimotor aligned perspectives were biased away from the memory aligned perspective, and responses for misaligned perspectives were biased toward sensorimotor aligned perspectives. These findings indicate that the spatial updating system is consistently independent of the spatial memory system regardless of the environments, but the updating system becomes less accessible as the environment changes from immediate to a retrieved one.

Dual Systems for Spatial Updating in Immediate and Retrieved Environments: Evidence from Bias Analysis

Directory of Open Access Journals (Sweden)

Chuanjun Liu

2018-02-01

Full Text Available The spatial updating and memory systems are employed during updating in both the immediate and retrieved environments. However, these dual systems seem to work differently, as the difference of pointing latency and absolute error between the two systems vary across environments. To verify this issue, the present study employed the bias analysis of signed errors based on the hypothesis that the transformed representation will bias toward the original one. Participants learned a spatial layout and then either stayed in the learning location or were transferred to a neighboring room directly or after being disoriented. After that, they performed spatial judgments from perspectives aligned with the learning direction, aligned with the direction they faced during the test, or a novel direction misaligned with the two above-mentioned directions. The patterns of signed error bias were consistent across environments. Responses for memory aligned perspectives were unbiased, whereas responses for sensorimotor aligned perspectives were biased away from the memory aligned perspective, and responses for misaligned perspectives were biased toward sensorimotor aligned perspectives. These findings indicate that the spatial updating system is consistently independent of the spatial memory system regardless of the environments, but the updating system becomes less accessible as the environment changes from immediate to a retrieved one.

Hollow Abutment Screw Design for Easy Retrieval in Case of Screw Fracture in Dental Implant System

Directory of Open Access Journals (Sweden)

Bo Kyun Sim

2017-01-01

Full Text Available The prosthetic component of dental implant is attached on the abutment which is connected to the fixture with an abutment screw. The abutment screw fracture is not frequent; however, the retrieval of the fractured screw is not easy, and it poses complications. A retrieval kit was developed which utilizes screw removal drills to make a hole on the fractured screw that provides an engaging drill to unscrew it. To minimize this process, the abutment screw is modified with a prefabricated access hole for easy retrieval. This study aimed to introduce this modified design of the abutment screw, the concept of easy retrieval, and to compare the mechanical strengths of the conventional and hollow abutment screws by finite element analysis (FEA and mechanical test. In the FEA results, both types of abutment screws showed similar stress distribution in the single artificial tooth system. A maximum load difference of about 2% occurred in the vertical load by a mechanical test. This study showed that the hollow abutment screw may be an alternative to the conventional abutment screws because this is designed for easy retrieval and that both abutment screws showed no significant difference in the mechanical tests and in the FEA.

Hollow Abutment Screw Design for Easy Retrieval in Case of Screw Fracture in Dental Implant System

Science.gov (United States)

Kim, Bongju; Shin, Yoo Jin

2017-01-01

The prosthetic component of dental implant is attached on the abutment which is connected to the fixture with an abutment screw. The abutment screw fracture is not frequent; however, the retrieval of the fractured screw is not easy, and it poses complications. A retrieval kit was developed which utilizes screw removal drills to make a hole on the fractured screw that provides an engaging drill to unscrew it. To minimize this process, the abutment screw is modified with a prefabricated access hole for easy retrieval. This study aimed to introduce this modified design of the abutment screw, the concept of easy retrieval, and to compare the mechanical strengths of the conventional and hollow abutment screws by finite element analysis (FEA) and mechanical test. In the FEA results, both types of abutment screws showed similar stress distribution in the single artificial tooth system. A maximum load difference of about 2% occurred in the vertical load by a mechanical test. This study showed that the hollow abutment screw may be an alternative to the conventional abutment screws because this is designed for easy retrieval and that both abutment screws showed no significant difference in the mechanical tests and in the FEA. PMID:29065610

Single-shell tank retrieval program mission analysis report

Energy Technology Data Exchange (ETDEWEB)

Stokes, W.J.

1998-08-11

This Mission Analysis Report was prepared to provide the foundation for the Single-Shell Tank (SST) Retrieval Program, a new program responsible for waste removal for the SSTS. The SST Retrieval Program is integrated with other Tank Waste Remediation System activities that provide the management, technical, and operations elements associated with planning and execution of SST and SST Farm retrieval and closure. This Mission Analysis Report provides the basis and strategy for developing a program plan for SST retrieval. This Mission Analysis Report responds to a US Department of Energy request for an alternative single-shell tank retrieval approach (Taylor 1997).

Single-shell tank retrieval program mission analysis report

International Nuclear Information System (INIS)

Stokes, W.J.

1998-01-01

This Mission Analysis Report was prepared to provide the foundation for the Single-Shell Tank (SST) Retrieval Program, a new program responsible for waste removal for the SSTS. The SST Retrieval Program is integrated with other Tank Waste Remediation System activities that provide the management, technical, and operations elements associated with planning and execution of SST and SST Farm retrieval and closure. This Mission Analysis Report provides the basis and strategy for developing a program plan for SST retrieval. This Mission Analysis Report responds to a US Department of Energy request for an alternative single-shell tank retrieval approach (Taylor 1997)

IMIRSEL: a secure music retrieval testing environment

Science.gov (United States)

Downie, John S.

2004-10-01

The Music Information Retrieval (MIR) and Music Digital Library (MDL) research communities have long noted the need for formal evaluation mechanisms. Issues concerning the unavailability of freely-available music materials have greatly hindered the creation of standardized test collections with which these communities could scientifically assess the strengths and weaknesses of their various music retrieval techniques. The International Music Information Retrieval Systems Evaluation Laboratory (IMIRSEL) is being developed at the University of Illinois at Urbana-Champaign (UIUC) specifically to overcome this hindrance to the scientific evaluation of MIR/MDL systems. Together with its subsidiary Human Use of Music Information Retrieval Systems (HUMIRS) project, IMIRSEL will allow MIR/MDL researchers access to the standardized large-scale collection of copyright-sensitive music materials and standardized test queries being housed at UIUC's National Center for Supercomputing Applications (NCSA). Virtual Research Labs (VRL), based upon NCSA's Data-to-Knowledge (D2K) tool set, are being developed through which MIR/MDL researchers will interact with the music materials under a "trusted code" security model.

Project W-320, 241-C-106 sluicing piping calculations, Volume 7

International Nuclear Information System (INIS)

Bailey, J.W.

1998-01-01

The object of this report is to calculate the hydraulic forces imposed at the sluicer nozzle. This is required by Project W-320 waste retrieval for tank 241-C-106. The method of analysis used is Bernoulli's momentum equation for stead flow

Measuring and Predicting Tag Importance for Image Retrieval.

Science.gov (United States)

Li, Shangwen; Purushotham, Sanjay; Chen, Chen; Ren, Yuzhuo; Kuo, C-C Jay

2017-12-01

Textual data such as tags, sentence descriptions are combined with visual cues to reduce the semantic gap for image retrieval applications in today's Multimodal Image Retrieval (MIR) systems. However, all tags are treated as equally important in these systems, which may result in misalignment between visual and textual modalities during MIR training. This will further lead to degenerated retrieval performance at query time. To address this issue, we investigate the problem of tag importance prediction, where the goal is to automatically predict the tag importance and use it in image retrieval. To achieve this, we first propose a method to measure the relative importance of object and scene tags from image sentence descriptions. Using this as the ground truth, we present a tag importance prediction model to jointly exploit visual, semantic and context cues. The Structural Support Vector Machine (SSVM) formulation is adopted to ensure efficient training of the prediction model. Then, the Canonical Correlation Analysis (CCA) is employed to learn the relation between the image visual feature and tag importance to obtain robust retrieval performance. Experimental results on three real-world datasets show a significant performance improvement of the proposed MIR with Tag Importance Prediction (MIR/TIP) system over other MIR systems.

Mobile medical image retrieval

Science.gov (United States)

Duc, Samuel; Depeursinge, Adrien; Eggel, Ivan; Müller, Henning

2011-03-01

Images are an integral part of medical practice for diagnosis, treatment planning and teaching. Image retrieval has gained in importance mainly as a research domain over the past 20 years. Both textual and visual retrieval of images are essential. In the process of mobile devices becoming reliable and having a functionality equaling that of formerly desktop clients, mobile computing has gained ground and many applications have been explored. This creates a new field of mobile information search & access and in this context images can play an important role as they often allow understanding complex scenarios much quicker and easier than free text. Mobile information retrieval in general has skyrocketed over the past year with many new applications and tools being developed and all sorts of interfaces being adapted to mobile clients. This article describes constraints of an information retrieval system including visual and textual information retrieval from the medical literature of BioMedCentral and of the RSNA journals Radiology and Radiographics. Solutions for mobile data access with an example on an iPhone in a web-based environment are presented as iPhones are frequently used and the operating system is bound to become the most frequent smartphone operating system in 2011. A web-based scenario was chosen to allow for a use by other smart phone platforms such as Android as well. Constraints of small screens and navigation with touch screens are taken into account in the development of the application. A hybrid choice had to be taken to allow for taking pictures with the cell phone camera and upload them for visual similarity search as most producers of smart phones block this functionality to web applications. Mobile information access and in particular access to images can be surprisingly efficient and effective on smaller screens. Images can be read on screen much faster and relevance of documents can be identified quickly through the use of images contained in

ADAPTING HYBRID MACHINE TRANSLATION TECHNIQUES FOR CROSS-LANGUAGE TEXT RETRIEVAL SYSTEM

Directory of Open Access Journals (Sweden)

P. ISWARYA

2017-03-01

Full Text Available This research work aims in developing Tamil to English Cross - language text retrieval system using hybrid machine translation approach. The hybrid machine translation system is a combination of rule based and statistical based approaches. In an existing word by word translation system there are lot of issues and some of them are ambiguity, Out-of-Vocabulary words, word inflections, and improper sentence structure. To handle these issues, proposed architecture is designed in such a way that, it contains Improved Part-of-Speech tagger, machine learning based morphological analyser, collocation based word sense disambiguation procedure, semantic dictionary, and tense markers with gerund ending rules, and two pass transliteration algorithm. From the experimental results it is clear that the proposed Tamil Query based translation system achieves significantly better translation quality over existing system, and reaches 95.88% of monolingual performance.

Comprehensive Information Retrieval and Model Input Sequence (CIRMIS)

International Nuclear Information System (INIS)

Friedrichs, D.R.

1977-04-01

The Comprehensive Information Retrieval and Model Input Sequence (CIRMIS) was developed to provide the research scientist with man--machine interactive capabilities in a real-time environment, and thereby produce results more quickly and efficiently. The CIRMIS system was originally developed to increase data storage and retrieval capabilities and ground-water model control for the Hanford site. The overall configuration, however, can be used in other areas. The CIRMIS system provides the user with three major functions: retrieval of well-based data, special application for manipulating surface data or background maps, and the manipulation and control of ground-water models. These programs comprise only a portion of the entire CIRMIS system. A complete description of the CIRMIS system is given in this report. 25 figures, 7 tables

Assimilation of SMOS Soil Moisture Retrievals in the Land Information System

Science.gov (United States)

Blakenship, Clay; Zavodsky, Bradley; Cae, Jonathan

2014-01-01

Soil moisture is a crucial variable for weather prediction because of its influence on evaporation. It is of critical importance for drought and flood monitoring and prediction and for public health applications. The NASA Short-term Prediction Research and Transition Center (SPoRT) has implemented a new module in the NASA Land Information System (LIS) to assimilate observations from the ESA's Soil Moisture and Ocean Salinity (SMOS) satellite. SMOS Level 2 retrievals from the Microwave Imaging Radiometer using Aperture Synthesis (MIRAS) instrument are assimilated into the Noah LSM within LIS via an Ensemble Kalman Filter. The retrievals have a target volumetric accuracy of 4% at a resolution of 35-50 km. Parallel runs with and without SMOS assimilation are performed with precipitation forcing from intentionally degraded observations, and then validated against a model run using the best available precipitation data, as well as against selected station observations. The goal is to demonstrate how SMOS data assimilation can improve modeled soil states in the absence of dense rain gauge and radar networks.

Music Information Retrieval.

Science.gov (United States)

Downie, J. Stephen

2003-01-01

Identifies MIR (Music Information Retrieval) computer system problems, historic influences, current state-of-the-art, and future MIR solutions through an examination of the multidisciplinary approach to MIR. Highlights include pitch; temporal factors; harmonics; tone; editorial, textual, and bibliographic facets; multicultural factors; locating…

Development of a multi-functional scarifier dislodger with an integral pneumatic conveyance retrieval system for single-shell tank remediation. FY93 summary report

International Nuclear Information System (INIS)

Bamberger, J.A.; McKinnon, M.A.; Alberts, D.A.; Steele, D.E.; Crowe, C.T.

1994-10-01

The Underground Storage Tank Integrated Demonstration (UST-ID) is evaluating several hydraulic dislodger concepts and retrieval technologies to develop specifications for system that can retrieve wastes from single-shell tanks. Each of the dislodgers will be evaluated sequentially to determine its ability to fracture and dislodge various waste simulants such as salt cake, sludge, and viscous liquid. The retrieval methods will be evaluated to determine their ability to convey this dislodged material from the tank. This report describes on-going research that commenced in FY93 to develop specifications for a scarifier dislodger coupled with a pneumatic conveyance retrieval system. The scarifier development is described in Section 3; pneumatic conveyance development is described in Section 4. Preliminary system specifications are listed in Section 5. FY94 plans are summarized in Section 6

Systems and Architectures for Multimedia Information Retrieval

NARCIS (Netherlands)

Djeraba, C.; Sebe, N.; Lew, M.S.

2005-01-01

In this paper, we provide a brief survey on multimedia information retrieval and we introduce some ideas investigated in the special issue. We hope that the contributions of this issue will stimulate the readers to tackle the current challenges and problems in this highly important research

Study of retrieval, utilize and circulation system for nuclear data in computerized media

International Nuclear Information System (INIS)

Ohbayasi, Yosihide

2001-01-01

We have shown and have developed a new type of nuclear data retrieval system, in which a nuclear reaction data compilation is applied as an example. To get benefits from recent computer and network technologies, we adopt the IntelligentPad architecture as a framework of the present system. We set the future aim of our database system toward the 'effective' use of nuclear reaction data: I. 'Re-produce, Re-edit, Re-use', II. 'Circulation, Evolution', III. 'Knowledge discovery'. We discuss the appropriate concepts, which fit for the above purpose. (author)

An Information Retrieval and Recommendation System for Astronomical Observatories

Science.gov (United States)

Mukund, Nikhil; Thakur, Saurabh; Abraham, Sheelu; Aniyan, A. K.; Mitra, Sanjit; Sajeeth Philip, Ninan; Vaghmare, Kaustubh; Acharjya, D. P.

2018-03-01

We present a machine-learning-based information retrieval system for astronomical observatories that tries to address user-defined queries related to an instrument. In the modern instrumentation scenario where heterogeneous systems and talents are simultaneously at work, the ability to supply people with the right information helps speed up the tasks for detector operation, maintenance, and upgradation. The proposed method analyzes existing documented efforts at the site to intelligently group related information to a query and to present it online to the user. The user in response can probe the suggested content and explore previously developed solutions or probable ways to address the present situation optimally. We demonstrate natural language-processing-backed knowledge rediscovery by making use of the open source logbook data from the Laser Interferometric Gravitational Observatory (LIGO). We implement and test a web application that incorporates the above idea for LIGO Livingston, LIGO Hanford, and Virgo observatories.

Contingency plan for deployment of the void fraction instrument in Tank 241-AY-102

International Nuclear Information System (INIS)

CONNER, J.M.

1999-01-01

High-heat producing sludge from tank 241-C-106 will be sluiced and transferred to tank 241-AY-102 beginning in October 1998. Safety analyses have postulated that after retrieval, the waste in 241-AY-102 may generate and retain unsafe levels of flammable gases (Noorani 1998, Pasamebmetoglu etal. 1997). Unsafe levels of retained gas are not expected, but cannot be ruled out because of the large uncertainty in the gas generation and retention rates. The Tank Waste Remediation System Basis for Interim Operation (Noorani 1998) identifies the need for a contingency plan to add void fraction monitoring to tank 241-AY-102 within 2 weeks of the identification of flammable gas buildup that would warrant monitoring. The Tank 241-C-106 Waste Retrieval Sluicing System Process Control Plan (Carothers et al. 1998) committed to providing a contingency plan for deployment of the void fraction instrument (VFI) in tank 241-AY-102. The VFI determines the local void fraction of the waste by compressing a waste sample captured in a gas-tight test chamber. The sample chamber is mounted on the end of a 76-cm (2.5-ft) arm that can be rotated from vertical to horizontal when the instrument is deployed. Once in the waste, the arm can be positioned horizontally and rotated to sample in different areas below the riser. The VFI is deployed using a crane. The VFI has been deployed previously in 241-AW, 241-AN, and 241-SY tank farms, most recently in tank 241-SY-101 in June and July 1998. An additional test in tank 241-SY-101 is planned in September 1998. Operating instructions for the VFI are included in the Void Fraction Instrument Operation and Maintenance Manual (Pearce 1994)

Phase modulated high density collinear holographic data storage system with phase-retrieval reference beam locking and orthogonal reference encoding.

Science.gov (United States)

Liu, Jinpeng; Horimai, Hideyoshi; Lin, Xiao; Huang, Yong; Tan, Xiaodi

2018-02-19

A novel phase modulation method for holographic data storage with phase-retrieval reference beam locking is proposed and incorporated into an amplitude-encoding collinear holographic storage system. Unlike the conventional phase retrieval method, the proposed method locks the data page and the corresponding phase-retrieval interference beam together at the same location with a sequential recording process, which eliminates piezoelectric elements, phase shift arrays and extra interference beams, making the system more compact and phase retrieval easier. To evaluate our proposed phase modulation method, we recorded and then recovered data pages with multilevel phase modulation using two spatial light modulators experimentally. For 4-level, 8-level, and 16-level phase modulation, we achieved the bit error rate (BER) of 0.3%, 1.5% and 6.6% respectively. To further improve data storage density, an orthogonal reference encoding multiplexing method at the same position of medium is also proposed and validated experimentally. We increased the code rate of pure 3/16 amplitude encoding method from 0.5 up to 1.0 and 1.5 using 4-level and 8-level phase modulation respectively.

Image Retrieval Berdasarkan Fitur Warna, Bentuk, dan Tekstur

Directory of Open Access Journals (Sweden)

Rita Layona

2014-12-01

Full Text Available Along with the times, information retrieval is no longer just on textual data, but also the visual data. The technique was originally used is Text-Based Image Retrieval (TBIR, but the technique still has some shortcomings such as the relevance of the picture successfully retrieved, and the specific space required to store meta-data in the image. Seeing the shortage of Text-Based Image Retrieval techniques, then other techniques were developed, namely Image Retrieval based on content or commonly called Content Based Image Retrieval (CBIR. In this research, CBIR will be discussed based on color, shape and texture using a color histogram, Gabor and SIFT. This study aimed to compare the results of image retrieval with some of these techniques. The results obtained are by combining color, shape and texture features, the performance of the system can be improved.

MRS [monitored retrievable storage] Systems Study Task 1 report: Waste management system reliability analysis

International Nuclear Information System (INIS)

Clark, L.L.; Myers, R.S.

1989-04-01

This is one of nine studies undertaken by contractors to the US Department of Energy (DOE), Office of Civilian Radioactive Waste Management (OCRWM), to provide a technical basis for re-evaluating the role of a monitored retrievable storage (MRS) facility. The study evaluates the relative reliabilities of systems with and without an MRS facility using current facility design bases. The principal finding of this report is that the MRS system has several operational advantages that enhance system reliability. These are: (1) the MRS system is likely to encounter fewer technical issues, (2) the MRS would assure adequate system surface storage capacity to accommodate repository construction and startup delays of up to five years or longer if the Nuclear Waste Policy Amendments Act (NWPAA) were amended, (3) the system with an MRS has two federal acceptance facilities with parallel transportation routing and surface storage capacity, and (4) the MRS system would allow continued waste acceptance for up to a year after a major disruption of emplacement operations at the repository

Dialog-based Interactive Image Retrieval

OpenAIRE

Guo, Xiaoxiao; Wu, Hui; Cheng, Yu; Rennie, Steven; Feris, Rogerio Schmidt

2018-01-01

Existing methods for interactive image retrieval have demonstrated the merit of integrating user feedback, improving retrieval results. However, most current systems rely on restricted forms of user feedback, such as binary relevance responses, or feedback based on a fixed set of relative attributes, which limits their impact. In this paper, we introduce a new approach to interactive image search that enables users to provide feedback via natural language, allowing for more natural and effect...

Selective memory retrieval can impair and improve retrieval of other memories.

Science.gov (United States)

Bäuml, Karl-Heinz T; Samenieh, Anuscheh

2012-03-01

Research from the past decades has shown that retrieval of a specific memory (e.g., retrieving part of a previous vacation) typically attenuates retrieval of other memories (e.g., memories for other details of the event), causing retrieval-induced forgetting. More recently, however, it has been shown that retrieval can both attenuate and aid recall of other memories (K.-H. T. Bäuml & A. Samenieh, 2010). To identify the circumstances under which retrieval aids recall, the authors examined retrieval dynamics in listwise directed forgetting, context-dependent forgetting, proactive interference, and in the absence of any induced memory impairment. They found beneficial effects of selective retrieval in listwise directed forgetting and context-dependent forgetting but detrimental effects in all the other conditions. Because context-dependent forgetting and listwise directed forgetting arguably reflect impaired context access, the results suggest that memory retrieval aids recall of memories that are subject to impaired context access but attenuates recall in the absence of such circumstances. The findings are consistent with a 2-factor account of memory retrieval and suggest the existence of 2 faces of memory retrieval. 2012 APA, all rights reserved

Emergent web intelligence advanced information retrieval

CERN Document Server

Badr, Youakim; Abraham, Ajith; Hassanien, Aboul-Ella

2010-01-01

Web Intelligence explores the impact of artificial intelligence and advanced information technologies representing the next generation of Web-based systems, services, and environments, and designing hybrid web systems that serve wired and wireless users more efficiently. Multimedia and XML-based data are produced regularly and in increasing way in our daily digital activities, and their retrieval must be explored and studied in this emergent web-based era. 'Emergent Web Intelligence: Advanced information retrieval, provides reviews of the related cutting-edge technologies and insights. It is v

Compact binary hashing for music retrieval

Science.gov (United States)

Seo, Jin S.

2014-03-01

With the huge volume of music clips available for protection, browsing, and indexing, there is an increased attention to retrieve the information contents of the music archives. Music-similarity computation is an essential building block for browsing, retrieval, and indexing of digital music archives. In practice, as the number of songs available for searching and indexing is increased, so the storage cost in retrieval systems is becoming a serious problem. This paper deals with the storage problem by extending the supervector concept with the binary hashing. We utilize the similarity-preserving binary embedding in generating a hash code from the supervector of each music clip. Especially we compare the performance of the various binary hashing methods for music retrieval tasks on the widely-used genre dataset and the in-house singer dataset. Through the evaluation, we find an effective way of generating hash codes for music similarity estimation which improves the retrieval performance.

Web information retrieval for health professionals.

Science.gov (United States)

Ting, S L; See-To, Eric W K; Tse, Y K

2013-06-01

This paper presents a Web Information Retrieval System (WebIRS), which is designed to assist the healthcare professionals to obtain up-to-date medical knowledge and information via the World Wide Web (WWW). The system leverages the document classification and text summarization techniques to deliver the highly correlated medical information to the physicians. The system architecture of the proposed WebIRS is first discussed, and then a case study on an application of the proposed system in a Hong Kong medical organization is presented to illustrate the adoption process and a questionnaire is administrated to collect feedback on the operation and performance of WebIRS in comparison with conventional information retrieval in the WWW. A prototype system has been constructed and implemented on a trial basis in a medical organization. It has proven to be of benefit to healthcare professionals through its automatic functions in classification and summarizing the medical information that the physicians needed and interested. The results of the case study show that with the use of the proposed WebIRS, significant reduction of searching time and effort, with retrieval of highly relevant materials can be attained.

MRS systems study, Task F: Transportation impacts of a monitored retrievable storage facility

Energy Technology Data Exchange (ETDEWEB)

Brentlinger, L.A.; Gupta, S.; Plummer, A.M.; Smith, L.A.; Tzemos, S.

1989-05-01

The passage of the Nuclear Waste Policy Amendments Act of 1987 (NWPAA) modified the basis from which the Office of Civilian Radioactive Waste Management (OCRWM) had derived and developed the configuration of major elements of the waste system (repository, monitored retrievable storage, and transportation). While the key aspects of the Nuclear Waste Policy Act of 1982 remain unaltered, NWPAA provisions focusing site characterization solely at Yucca Mountain, authorizing a monitored retrievable storage (MRS) facility with specific linkages to the repository, and establishing an MRS Review Commission make it prudent for OCRWM to update its analysis of the role of the MRS in the overall waste system configuration. This report documents the differences in transportation costs and radiological dose under alternative scenarios pertaining to a nuclear waste management system with and without an MRS, to include the effect of various MRS packaging functions and locations. The analysis is limited to the impacts of activities related directly to the hauling of high-level radioactive waste (HLW), including the capital purchase and maintenance costs of the transportation cask system. Loading and unloading impacts are not included in this study because they are treated as facility costs in the other task reports. Transportation costs are based on shipments of 63,000 metric tons of uranium (MTU) of spent nuclear fuel and 7,000 MTU equivalent of HLW. 10 refs., 41 tabs.

Pareto-depth for multiple-query image retrieval.

Science.gov (United States)

Hsiao, Ko-Jen; Calder, Jeff; Hero, Alfred O

2015-02-01

Most content-based image retrieval systems consider either one single query, or multiple queries that include the same object or represent the same semantic information. In this paper, we consider the content-based image retrieval problem for multiple query images corresponding to different image semantics. We propose a novel multiple-query information retrieval algorithm that combines the Pareto front method with efficient manifold ranking. We show that our proposed algorithm outperforms state of the art multiple-query retrieval algorithms on real-world image databases. We attribute this performance improvement to concavity properties of the Pareto fronts, and prove a theoretical result that characterizes the asymptotic concavity of the fronts.

Foreign Body Retrieval

Medline Plus

Full Text Available ... Physician Resources Professions Site Index A-Z Foreign Body Retrieval Foreign body retrieval is the removal of ... foreign body detection and removal? What is Foreign Body Retrieval? Foreign body retrieval involves the removal of ...

Remote technologies for buried waste retrieval

International Nuclear Information System (INIS)

Smith, A.M.; Rice, P.

1995-01-01

The DOE is evaluating what should be done with this buried waste. Although the radioactive waste is not particularly mobile unless airborne, some of it was buried with volatile organics and/or other substances that tend to spread easily to surrounding soil or water tables. Volatile organics are hazardous materials (such as trichloroethylene) and require clean-up at certain levels in drinking water. There is concern that the buried volatile organics will spread into the water table and contaminate drinking water. Because of this, the DOE is considering options for handling this buried waste and reducing the risks of spreading or exposure. There are two primary options: containment and stabilization, or retrieval. Containment and stabilization systems would include systems that would leave the waste where it is, but contain and stabilize it so that the radioactive and hazardous materials would not spread to the surrounding soil, water, or air. For example, an in situ vitrification system could be used to melt the waste into a composite glass-like material that would not leach into the surrounding soil, water, or air. Retrieval systems are those that would remove the waste from its burial location for treatment and/or repackaging for long term storage. The objective of this project was to develop and demonstrate remote technologies that would minimize dust generation and the spread of airborne contaminants during buried waste retrieval. Remote technologies are essential for the retrieval of buried waste because they remove workers from the hazardous environment and provide greater automation, reducing the chances of human error. Minimizing dust generation is also essential to increased safety for the workers and the environment during buried waste retrieval. The main contaminants within the waste are micron-sized particles of plutonium and americium oxides, chlorides, and hydroxides, which are easily suspended in air and spread if disturbed

The role of retrieval mode and retrieval orientation in retrieval practice: insights from comparing recognition memory testing formats and restudying.

Science.gov (United States)

Gao, Chuanji; Rosburg, Timm; Hou, Mingzhu; Li, Bingbing; Xiao, Xin; Guo, Chunyan

2016-12-01

The effectiveness of retrieval practice for aiding long-term memory, referred to as the testing effect, has been widely demonstrated. However, the specific neurocognitive mechanisms underlying this phenomenon remain unclear. In the present study, we sought to explore the role of pre-retrieval processes at initial testing on later recognition performance by using event-related potentials (ERPs). Subjects studied two lists of words (Chinese characters) and then performed a recognition task or a source memory task, or restudied the word lists. At the end of the experiment, subjects received a final recognition test based on the remember-know paradigm. Behaviorally, initial testing (active retrieval) enhanced memory retention relative to restudying (passive retrieval). The retrieval mode at initial testing was indexed by more positive-going ERPs for unstudied items in the active-retrieval tasks than in passive retrieval from 300 to 900 ms. Follow-up analyses showed that the magnitude of the early ERP retrieval mode effect (300-500 ms) was predictive of the behavioral testing effect later on. In addition, the ERPs for correctly rejected new items during initial testing differed between the two active-retrieval tasks from 500 to 900 ms, and this ERP retrieval orientation effect predicted differential behavioral testing gains between the two active-retrieval conditions. Our findings confirm that initial testing promotes later retrieval relative to restudying, and they further suggest that adopting pre-retrieval processing in the forms of retrieval mode and retrieval orientation might contribute to these memory enhancements.

NOAA JPSS Microwave Integrated Retrieval System (MIRS) Advanced Technology Microwave Sounder (ATMS) Sounding Products from NDE

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — This dataset contains temperature and humidity profiles from the NOAA Microwave Integrated Retrieval System (MIRS) using sensor data from the Advanced Technology...

Automated Medical Literature Retrieval

Directory of Open Access Journals (Sweden)

David Hawking

2012-09-01

Full Text Available Background The constantly growing publication rate of medical research articles puts increasing pressure on medical specialists who need to be aware of the recent developments in their field. The currently used literature retrieval systems allow researchers to find specific papers; however the search task is still repetitive and time-consuming. Aims In this paper we describe a system that retrieves medical publications by automatically generating queries based on data from an electronic patient record. This allows the doctor to focus on medical issues and provide an improved service to the patient, with higher confidence that it is underpinned by current research. Method Our research prototype automatically generates query terms based on the patient record and adds weight factors for each term. Currently the patient’s age is taken into account with a fuzzy logic derived weight, and terms describing blood-related anomalies are derived from recent blood test results. Conditionally selected homonyms are used for query expansion. The query retrieves matching records from a local index of PubMed publications and displays results in descending relevance for the given patient. Recent publications are clearly highlighted for instant recognition by the researcher. Results Nine medical specialists from the Royal Adelaide Hospital evaluated the system and submitted pre-trial and post-trial questionnaires. Throughout the study we received positive feedback as doctors felt the support provided by the prototype was useful, and which they would like to use in their daily routine. Conclusion By supporting the time-consuming task of query formulation and iterative modification as well as by presenting the search results in order of relevance for the specific patient, literature retrieval becomes part of the daily workflow of busy professionals.

Peer to Peer Information Retrieval: An Overview

NARCIS (Netherlands)

Tigelaar, A.S.; Hiemstra, D.; Trieschnigg, D.

2012-01-01

Peer-to-peer technology is widely used for file sharing. In the past decade a number of prototype peer-to-peer information retrieval systems have been developed. Unfortunately, none of these have seen widespread real- world adoption and thus, in contrast with file sharing, information retrieval is

Peer to Peer Information Retrieval: An Overview

NARCIS (Netherlands)

Tigelaar, A.S.; Hiemstra, Djoerd; Trieschnigg, Rudolf Berend

Peer-to-peer technology is widely used for file sharing. In the past decade a number of prototype peer-to-peer information retrieval systems have been developed. Unfortunately, none of these have seen widespread real- world adoption and thus, in contrast with file sharing, information retrieval is

Care episode retrieval: distributional semantic models for information retrieval in the clinical domain.

Science.gov (United States)

Moen, Hans; Ginter, Filip; Marsi, Erwin; Peltonen, Laura-Maria; Salakoski, Tapio; Salanterä, Sanna

2015-01-01

Patients' health related information is stored in electronic health records (EHRs) by health service providers. These records include sequential documentation of care episodes in the form of clinical notes. EHRs are used throughout the health care sector by professionals, administrators and patients, primarily for clinical purposes, but also for secondary purposes such as decision support and research. The vast amounts of information in EHR systems complicate information management and increase the risk of information overload. Therefore, clinicians and researchers need new tools to manage the information stored in the EHRs. A common use case is, given a--possibly unfinished--care episode, to retrieve the most similar care episodes among the records. This paper presents several methods for information retrieval, focusing on care episode retrieval, based on textual similarity, where similarity is measured through domain-specific modelling of the distributional semantics of words. Models include variants of random indexing and the semantic neural network model word2vec. Two novel methods are introduced that utilize the ICD-10 codes attached to care episodes to better induce domain-specificity in the semantic model. We report on experimental evaluation of care episode retrieval that circumvents the lack of human judgements regarding episode relevance. Results suggest that several of the methods proposed outperform a state-of-the art search engine (Lucene) on the retrieval task.

A Simple Method to Determine if a Music Information Retrieval System is a "Horse"

DEFF Research Database (Denmark)

Sturm, Bob L.

2014-01-01

We propose and demonstrate a simple method to determine if a music information retrieval (MIR) system is using factors irrelevant to the task for which it is designed. This is of critical importance to certain use cases, but cannot be accomplished using standard approaches to evaluation in MIR...

Retrieval-Induced Inhibition in Short-Term Memory.

Science.gov (United States)

Kang, Min-Suk; Choi, Joongrul

2015-07-01

We used a visual illusion called motion repulsion as a model system for investigating competition between two mental representations. Subjects were asked to remember two random-dot-motion displays presented in sequence and then to report the motion directions for each. Remembered motion directions were shifted away from the actual motion directions, an effect similar to the motion repulsion observed during perception. More important, the item retrieved second showed greater repulsion than the item retrieved first. This suggests that earlier retrieval exerted greater inhibition on the other item being held in short-term memory. This retrieval-induced motion repulsion could be explained neither by reduced cognitive resources for maintaining short-term memory nor by continued inhibition between short-term memory representations. These results indicate that retrieval of memory representations inhibits other representations in short-term memory. We discuss mechanisms of retrieval-induced inhibition and their implications for the structure of memory. © The Author(s) 2015.

IMAGE DESCRIPTIONS FOR SKETCH BASED IMAGE RETRIEVAL

OpenAIRE

SAAVEDRA RONDO, JOSE MANUEL; SAAVEDRA RONDO, JOSE MANUEL

2008-01-01

Due to the massive use of Internet together with the proliferation of media devices, content based image retrieval has become an active discipline in computer science. A common content based image retrieval approach requires that the user gives a regular image (e.g, a photo) as a query. However, having a regular image as query may be a serious problem. Indeed, people commonly use an image retrieval system because they do not count on the desired image. An easy alternative way t...

[A retrieval method of drug molecules based on graph collapsing].

Science.gov (United States)

Qu, J W; Lv, X Q; Liu, Z M; Liao, Y; Sun, P H; Wang, B; Tang, Z

2018-04-18

To establish a compact and efficient hypergraph representation and a graph-similarity-based retrieval method of molecules to achieve effective and efficient medicine information retrieval. Chemical structural formula (CSF) was a primary search target as a unique and precise identifier for each compound at the molecular level in the research field of medicine information retrieval. To retrieve medicine information effectively and efficiently, a complete workflow of the graph-based CSF retrieval system was introduced. This system accepted the photos taken from smartphones and the sketches drawn on tablet personal computers as CSF inputs, and formalized the CSFs with the corresponding graphs. Then this paper proposed a compact and efficient hypergraph representation for molecules on the basis of analyzing factors that directly affected the efficiency of graph matching. According to the characteristics of CSFs, a hierarchical collapsing method combining graph isomorphism and frequent subgraph mining was adopted. There was yet a fundamental challenge, subgraph overlapping during the collapsing procedure, which hindered the method from establishing the correct compact hypergraph of an original CSF graph. Therefore, a graph-isomorphism-based algorithm was proposed to select dominant acyclic subgraphs on the basis of overlapping analysis. Finally, the spatial similarity among graphical CSFs was evaluated by multi-dimensional measures of similarity. To evaluate the performance of the proposed method, the proposed system was firstly compared with Wikipedia Chemical Structure Explorer (WCSE), the state-of-the-art system that allowed CSF similarity searching within Wikipedia molecules dataset, on retrieval accuracy. The system achieved higher values on mean average precision, discounted cumulative gain, rank-biased precision, and expected reciprocal rank than WCSE from the top-2 to the top-10 retrieved results. Specifically, the system achieved 10%, 1.41, 6.42%, and 1

Development of digital dashboard system for medical practice: maximizing efficiency of medical information retrieval and communication.

Science.gov (United States)

Lee, Kee Hyuck; Yoo, Sooyoung; Shin, HoGyun; Baek, Rong-Min; Chung, Chin Youb; Hwang, Hee

2013-01-01

It is reported that digital dashboard systems in hospitals provide a user interface (UI) that can centrally manage and retrieve various information related to patients in a single screen, support the decision-making of medical professionals on a real time basis by integrating the scattered medical information systems and core work flows, enhance the competence and decision-making ability of medical professionals, and reduce the probability of misdiagnosis. However, the digital dashboard systems of hospitals reported to date have some limitations when medical professionals use them to generally treat inpatients, because those were limitedly used for the work process of certain departments or developed to improve specific disease-related indicators. Seoul National University Bundang Hospital developed a new concept of EMR system to overcome such limitations. The system allows medical professionals to easily access all information on inpatients and effectively retrieve important information from any part of the hospital by displaying inpatient information in the form of digital dashboard. In this study, we would like to introduce the structure, development methodology and the usage of our new concept.

FIRES: Fire Information Retrieval and Evaluation System - A program for fire danger rating analysis

Science.gov (United States)

Patricia L. Andrews; Larry S. Bradshaw

1997-01-01

A computer program, FIRES: Fire Information Retrieval and Evaluation System, provides methods for evaluating the performance of fire danger rating indexes. The relationship between fire danger indexes and historical fire occurrence and size is examined through logistic regression and percentiles. Historical seasonal trends of fire danger and fire occurrence can be...

Sludge Treatment Project Engineered Container Retrieval And Transfer System Prelminary Design Hazard And Operability Study

International Nuclear Information System (INIS)

Carro, C.A.

2011-01-01

This Hazard and Operability (HAZOP) study addresses the Sludge Treatment Project (STP) Engineered Container Retrieval and Transfer System (ECRTS) preliminary design for retrieving sludge from underwater engineered containers located in the 105-K West (KW) Basin, transferring the sludge as a sludge-water slurry (hereafter referred to as 'slurry') to a Sludge Transport and Storage Container (STSC) located in a Modified KW Basin Annex, and preparing the STSC for transport to T Plant using the Sludge Transport System (STS). There are six, underwater engineered containers located in the KW Basin that, at the time of sludge retrieval, will contain an estimated volume of 5.2 m 3 of KW Basin floor and pit sludge, 18.4 m 3 of 105-K East (KE) Basin floor, pit, and canister sludge, and 3.5 m 3 of settler tank sludge. The KE and KW Basin sludge consists of fuel corrosion products (including metallic uranium, and fission and activation products), small fuel fragments, iron and aluminum oxide, sand, dirt, operational debris, and biological debris. The settler tank sludge consists of sludge generated by the washing of KE and KW Basin fuel in the Primary Clean Machine. A detailed description of the origin of sludge and its chemical and physical characteristics can be found in HNF-41051, Preliminary STP Container and Settler Sludge Process System Description and Material Balance. In summary, the ECRTS retrieves sludge from the engineered containers and hydraulically transfers it as a slurry into an STSC positioned within a trailer-mounted STS cask located in a Modified KW Basin Annex. The slurry is allowed to settle within the STSC to concentrate the solids and clarify the supernate. After a prescribed settling period the supernate is decanted. The decanted supernate is filtered through a sand filter and returned to the basin. Subsequent batches of slurry are added to the STSC, settled, and excess supernate removed until the prescribed quantity of sludge is collected. The sand

User-Based Information Retrieval System Interface Evaluation: An Examination of an On-Line Public Access Catalog.

Science.gov (United States)

Hert, Carol A.; Nilan, Michael S.

1991-01-01

Presents preliminary data that characterizes the relationship between what users say they are trying to accomplish when using an online public access catalog (OPAC) and their perceptions of what input to give the system. Human-machine interaction is discussed, and appropriate methods for evaluating information retrieval systems are considered. (18…

Automatic medical image annotation and keyword-based image retrieval using relevance feedback.

Science.gov (United States)