Process of gas manufacture: retorts

Energy Technology Data Exchange (ETDEWEB)

Henderson, N M

1883-01-01

Improvements in the process and apparatus for the destructive distillation of shale, etc., described in Specification No. 1327, A.D. 1873. According to one modification a series of vertical retorts are arranged opposite to each other in two rows, the retorts in each row having flue spaces between them. The retorts have inclined bottoms beneath which are combustion chambers connected by flues to the spaces, and by flues to regenerative chambers, provided with flues, arranged with suitable valves. The fresh air and combustible gas enter at the bottom of one pair of regenerators, and after being heated enter one of the chambers, where they are ignited. The products pass through the adjacent spaces, which are connected at the top, and having heated the retorts pass through the other chamber and through the other pair of regenerators to the chimney. The retorts opposite to each other are connected by a port at the top, and they are charged alternately with fresh material. Each retort is fitted with an outlet pipe leading to a main, and with a steam jet by which air and steam may be forced into the mouth piece. The fresh charge is subjected to a comparatively low temperature at first to distill the oil, and then a higher heat is applied to the partially-spent shale and highly-superheated steam, and air admitted to the retort to decompose the coke and drive off the remaining carbon and ammonia.

Conditioning of radioactive ash residue in a wave of solid-phase exothermal reactions

International Nuclear Information System (INIS)

Karlina, O.K.; Varlakova, G.A.; Ozhovan, M.I.; Tivanskij, V.M.; Dmitriev, S.A.

2001-01-01

The abilities for utilization of exothermic reaction heat in solid phase for conditioning the ash residue produced as a result of solid radioactive waste burning are analyzed. It is shown that the process of ash residue making monolithic with obtaining the glass-like finish product containing 50-60 mass % of ash residue which meets the requirements for solidified radioactive wastes may be realized without energy supplying from external heat sources. The conditioning is realized in a special crucible furnace-container designed not only for the process conducting but also for subsequent storage or disposal of the finish product [ru

Feeding device for rotary retorts

Energy Technology Data Exchange (ETDEWEB)

Hutchins, T W.S.

1923-04-25

A horizontal rotary retort is heated externally with a feeding-worm or the like for distilling coal, oil shale, etc. It is characterized in that the shaft of the feeder moves adjustably lengthwise, so that, under the hopper more or less of the worm comes for action on the feed, so that the hopper is withdrawn through the retort while it projects into the retort and is secured in a position against the rotation.

Retorts for distilling carbonaceous material

Energy Technology Data Exchange (ETDEWEB)

Lutz, H E

1921-09-12

A retort for distilling carbonaceous material is described in which a mass of such material is retained in a pocket formed between an outer wall and an internal wall which is perforated to permit the free escape of distilled products, the retorts having heating means that directly heat the retort but are so related to the pocket that the material therein is heated indirectly and simultaneously from all sides entirely by heat conducted thereto by the walls.

Potential for thermochemical conversion of biomass residues from the integrated sugar-ethanol process - Fate of ash and ash-forming elements.

Science.gov (United States)

Dirbeba, Meheretu Jaleta; Brink, Anders; DeMartini, Nikolai; Zevenhoven, Maria; Hupa, Mikko

2017-06-01

In this work, potential for thermochemical conversion of biomass residues from an integrated sugar-ethanol process and the fate of ash and ash-forming elements in the process are presented. Ash, ash-forming elements, and energy flows in the process were determined using mass balances and analyses of eight different biomass samples for ash contents, elemental compositions, and heating values. The results show that the ash content increases from the sugarcane to the final residue, vinasse. The cane straw, which is left in the field, contains one-third of the energy and 25% of the K and Cl while the vinasse contains 2% of the energy and 40% of the K and Cl in the cane. K and Cl in biomass fuels cause corrosion and fouling problems in boilers and gasifiers. Over 85% of these elements in the straw are water soluble indicating that water leaching would improve it for utilization in thermochemical conversion. Copyright © 2017 Elsevier Ltd. All rights reserved.

Retort furnaces

Energy Technology Data Exchange (ETDEWEB)

Pieters, J

1924-07-23

Retorts for the distillation of materials such as lignite, peat, or sawdust having a high moisture content are disposed in series in two directions at right angles to each other in a single block of masonry and are separated by longitudinal walls pierced by channels for heating gases and for escape of the distillation products. The oval retorts have between them flues with passages for the escape of the distillation gases which pass to a main. The material is charged into a hopper serving all the retorts and drying the material by the hot burnt gases which pass from a passage through branches to ducts at the base of the drier, these ducts being covered by funnels for filling the vertical chambers. The distillation gases after purification in the by-product recovery plant are burned in burners and combustion spaces, the hot gases circulating in channels before escaping by passage. The temperature in zone A is 400 to 500/sup 0/C and in zone B a higher temperature is attained. The coke is cooled by superheated steam injected through channels, water gas being generated and the material is further cooled by steam circulating in passages.

Improvements in retorting apparatus for fractional distillation

Energy Technology Data Exchange (ETDEWEB)

Cripps, W S

1933-05-05

A retort is located within a cylindrical chamber with annular space between them. The products of combustion from a furnace pass into said annular space. A flue pipe carries off gases from said space. A perforated plate located at the bottom of the retort and means are located within the furnace for heating air and superheating steam. Perforated pipes deliver air and steam to the retort and a condenser is provided wherein oil vapour produced in the retort is condensed.

Retort for coal, shale, and other carbonaceous material

Energy Technology Data Exchange (ETDEWEB)

Moure, K R

1930-12-15

A truncated conical retort chamber is described with a water tank or pit below the level of the floor of the retort, an aperture is the base of the retort chamber, a water-sealed chamber is interposed between the aperture at the base of the retort chamber and the water tank or pit, the upper end of the water-sealed chamber is connected to the retort chamber so as to make an air-tight joint therewith. Its lower end is submerged in the water in the tank or pit, an endless chain grate rotatably mounted upon a frame upon the floor of the retort chamber. The chain grate is inclined toward and projecting through the aperture at the base of the retort chamber into the water-sealed chamber for the purpose of conveying the spent material from the retort chamber to the water-sealed chamber through which it will gravitate to the water tank or pit. Means such as a bucket conveyor are provided for raising the spent material from the water tank or pit. Means are provided for rotating the endless chain grate, superimposed cylindrical feed chambers are upon the top of and in axial line with the retort chamber, a coned valve is interposed between the retort chamber and the next adjacent cylindrical chamber, another valve is interposed between the upper and lower cylindrical chambers. Means are provided for opening and closing the valves alternately, a discharge aperature is at or near the top of the retortchamber, and means are provided for feeding the material into the uppermost cylindrical feed chamber.

Retorting of bituminous sands

Energy Technology Data Exchange (ETDEWEB)

Chaney, P E; Ince, R W; Mason, C M

1872-09-26

This method of recovering oil from mined tar sands involves forming compacted tar sands pieces by special conditioning treatment that provides low internal permeability. The compacted pieces are then retorted in fixed bed form. The conditioning treatment can involve rolling of preformed pellets, compaction in a mold or pressure extrusion. Substantial collapsing of the bed during retorting is avoided. (9 claims) (Abstract only - original article not available from T.U.)

Retort

Energy Technology Data Exchange (ETDEWEB)

Salerni, P M

1928-03-28

A retort is described for the distillation of carbonaceous material, such as coal, oil shale, and the like, for the recovery of hydrocarbon oils, in which the coal is fed on to annular trays which are surrounded by shrouds having projecting rims. The coal is agitated in each of the trays by stirring members which are attached by links and to a rotary structure which is rotated by worm gearing. A gap is provided in each rim through which the material is transferred from each tray to the next succeeding lower tray, and in falling through the gap it drops on to the rim of the shroud of the next succeeding lower tray and the residue finally drops into a trough and a scraper on the rotatable ring directs it into an outlet. Vapors are drawn off through outlets. A central heating space contains a fireclay tube having a combustion chamber with burners at the lower part. The products of combustion pass through openings into the space, and thence through an outlet into a hopper for preheating the coal which is to be supplied to the trays.

Scoping of fusion-driven retorting of oil shale

International Nuclear Information System (INIS)

Galloway, T.R.

1979-11-01

In the time frame beyond 2005, fusion reactors are likely to make their first appearance when the oil shale industry will probably be operating with 20% of the production derived from surface retorts operating on deep mined shale from in situ retorts and 80% from shale retorted within these in situ retorts using relatively fine shale uniformly rubblized by expensive mining methods. A process was developed where fusion reactors supply a 600 0 C mixture of nitrogen, carbon dioxide, and water vapor to both surface and in situ retorts. The in situ production is accomplished by inert gas retorting, without oxygen, avoiding the burning of oil released from the larger shale particles produced in a simpler mining method. These fusion reactor-heated gases retort the oil from four 50x50x200m in-situ rubble beds at high rate of 40m/d and high yield (i.e., 95% F.A.), which provided high return on investment around 20% for the syncrude selling at $20/bbl, or 30% if sold as $30/bbl for heating oil. The bed of 600 0 C retorted shale, or char, left behind was then burned by the admission of ambient air in order to recover all of the possible energy from the shale resource. The hot combustion gases, mostly nitrogen, carbon dioxide and water vapor are then heat-exchanged with fusion reactor blanket coolant flow to be sequentially introduced into the next rubble bed ready for retorting. The advantages of this fusion-driven retorting process concept are a cheaper mining method, high yield and higher production rate system, processing with shale grades down to 50 l/mg (12 gpt), improved resource recovery by complete char utilization and low energy losses by leaving behind a cold, spent bed

Quality of ready to serve tilapia fish curry with PUFA in retortable pouches.

Science.gov (United States)

Dhanapal, K; Reddy, G V S; Nayak, B B; Basu, S; Shashidhar, K; Venkateshwarlu, G; Chouksey, M K

2010-09-01

Studies on the physical, chemical, and microbiological qualities of fresh tilapia meat revealed its suitability for the preparation of ready to eat fish curry packed in retort pouches. Studies on the fatty acid profile of tilapia meat suggest fortification with polyunsaturated fatty acid (PUFA) to increase the nutritional value. Based on the commercial sterility, sensory evaluation, color, and texture profile analysis F(0) value of 6.94 and cook value of 107.24, with a total process time of 50.24 min at 116 °C was satisfactory for the development of tilapia fish curry in retort pouches. Thermally processed ready to eat south Indian type tilapia fish curry fortified with PUFA was developed and its keeping quality studied at ambient temperature. During storage, a slight increase in the fat content of fish meat was observed, with no significant change in the contents of moisture, protein, and ash. The thiobarbituric acid (TBA) values of fish curry significantly increased during storage. Fish curry fortified with 1% cod liver oil and fish curry without fortification (control) did not show any significant difference in the levels of eicosapentaenoic acid (EPA) and docosahexaenoic acid (DHA), during thermal processing and storage. Sensory analysis revealed that fortification of fish curry with cod liver oil had no impact on the quality. Tilapia fish curry processed at 116 °C and F(0) value of 7.0 (with or without fortification of cod liver oil) was fit for consumption, even after a period of 1-y storage in retort pouch. Tilapia is a lean variety of fish with white flesh and therefore an ideal choice as raw material for the development of ready to serve fish products such as fish curry in retort pouches for both domestic and international markets. Ready to eat thermal processed (116 °C and F(0) value of 7.0) south Indian type tilapia fish curry enriched with PUFA and packed in retort pouch was acceptable for consumption even after a storage period of 1 y at ambient

Processing of chopped mussel meat in retort pouch

Directory of Open Access Journals (Sweden)

Giustino TRIBUZI

2015-01-01

Full Text Available Abstract Chopped mussel meat packaged in retort pouches was processed in a laboratory-scale water immersion retort, adapted for processing under overpressure conditions. Retort temperature effects on product yield and on cook value were evaluated by setting the F0 at 7 min. The effects of different pre-treatments (salting and marination on the characteristics of mussels were evaluated after processing at retort temperature of 118 °C and during a whole year of storage at 25 °C. The salted samples showed better yield during storage, while no differences were found for the other physicochemical parameters.

Hydrogen retorting of oil shales from Eastern Canada

Energy Technology Data Exchange (ETDEWEB)

Furimsky, E. (CANMET, Ottawa, Ontario (Canada)); Synnott, J.; Boorman, R.S.; Salter, R.S.

1984-04-01

The liquid production potential of thirty oil shale samples from Eastern Canada was determined by Fischer assay retort and pyrochem retort. For all shales, the presence of hydrogen during pyrochem retorting resulted in a significant increase in oil yields compared to Fischer assay yields. Ten oil shale samples were selected for detailed evaluation in the pyrochem retort in the presence of nitrogen and hydrogen. Besides increasing yields, the presence of hydrogen lowered the specific gravity of liquid products and the content of sulphur but increased the content of nitrogen. This was attributed to the stabilization of precursors to nitrogen compounds which prevented their polymerization. (J.H.K.)

Rotary retort for carbonizing bituminous materials

Energy Technology Data Exchange (ETDEWEB)

Meguin, A G; Muller, W

1920-09-05

A process of carbonizing bituminous materials, such as coal and oil shale at a low temperature in a rotary retort with simultaneous compressing the material especially of the semicoke formed that is characterized in that the material during the distillation through rapid rotation of the retort is exposed to the action of centrifugal force and thereby it is compressed.

Gas-retorts

Energy Technology Data Exchange (ETDEWEB)

1920-07-10

A vertical retort for the continuous distillation of coal, peat, shale, lignite, etc., is provided with a perforated gas withdrawal pipe in the upper part. The central part is surrounded by a heating-flue, and the lower part is provided with a conical discharging-screw mounted in a rotary water-pan.

Retorts

Energy Technology Data Exchange (ETDEWEB)

Bilbrough, S B

1917-01-11

In the process of distilling coal at a temperature of from 800 to 1,200/sup 0/C, a means such as a central perforated tube, which may be a rotary one is employed for withdrawing the gases of distillation in such a way as to prevent them from coming into contact with the walls of the retort. One means of withdrawal comprises a tube tapering downward formed with perforations. Modifications are also shown.

The influence of electrodialytic remediation on dioxin (PCDD/PCDF) levels in fly ash and air pollution control residues

DEFF Research Database (Denmark)

Dias-Ferreira, Celia; Kirkelund, Gunvor Marie; Jensen, Pernille Erland

2016-01-01

dibenzo-p-dioxins (PCDD) and polychlorinated dibenzofurans (PCDF), and how these levels impact on the valorization options for fly ash and APC residue.PCDD/PCDF levels in the original residues ranged between 4.85 and 197 ng g-1, being higher for the electrostatic precipitator fly ash. The toxic equivalent...

Characterization of Bottom and Fly Ashes Generated Co-incineration of Biomass with Automotive Shredder Residue

Directory of Open Access Journals (Sweden)

Othaman Muhamad Fazli

2017-01-01

Full Text Available One of the viable techniques to reduce land filling of automotive shredder residue is by co-incinerating them with biomass. This study focuses on characterization of bottom and fly ashes produced from the coincineration of the automotive shredded residue with oil palm biomass. The co-incineration was carried out in a pilot-scale fluidized bed incinerator. The oil palm biomass used was oil palm shell while the automotive shredded residue was obtained from a local recycling company. The characterization was done based on particle size distribution, morphology (SEM analysis and chemical composition (EDS analysis. In term of chemical composition the ashes contain C (Carbon, O (Oxygen, Si (Silicon, K (Potassium, Ca (Calcium and Fe (Ferum.

Change in mechanical properties of Antrim oil shale on retorting

Energy Technology Data Exchange (ETDEWEB)

Singh, S. P.; Hockings, W. A.; Kim, K.

1979-01-01

The decomposition of kerogen in oil shale and subsequent extraction of the decomposition products during the retorting process are known to alter the pore structure, resulting in changes in permeability, deformation and strength properties. Prediction of these changes is of fundamental importance in the design of in-situ retorting processes. This paper summarizes a comprehensive laboratory investigation on the changes in mechanical properties of Antrim oil shale on retorting at 500/sup 0/C. It was observed that kerogen plays an important role in the change of the properties on retorting. When subjected to heat, the degree of deformation, the extent of fracturing and the structural instability of the specimens appeared to be strongly dependent upon kerogen content. The values of elastic modulus, strength, and density decreased whereas maximum strain at failure increased on retorting. Significant increases in permeability and porosity also resulted from retorting. The most pronounced increase was observed in the permeability in the direction parallel to bedding which exceeded in some cases as much as 3 orders of magnitude. Microscopic observations of pore structures provided a qualitative support to data obtained in measurements of porosity and permeability.

Determining Permissible Oxygen and Water Vapor Transmission Rate for Non-Retort Military Ration Packaging

Science.gov (United States)

2011-11-01

OXYGEN AND WATER VAPOR TRANSMISSION RATE FOR NON- RETORT MILITARY RATION PACKAGING by Danielle Froio Alan Wright Nicole Favreau and Sarah...ANSI Std. Z39.18 RETORT STORAGE SHELF LIFE RETORT POUCHES SENSORY ANALYSIS OXYGEN CRACKERS PACKAGING SENSORY... Packaging for MRE. (a) MRE Retort Pouch Quad-Laminate Structure; (b) MRE Non- retort Pouch Tri-Laminate Structure

Vertical retort with arrangements for special heating, etc

Energy Technology Data Exchange (ETDEWEB)

Hengstenberg, R

1922-02-28

A vertical retort with arrangements for special heating of upper and lower zones and special gas outlets on the highest and lowest parts of the retort is characterized in that the lower gas outlet on the one side serves for feeding the burner for heating both upper zone as well as the lower, and on the other side runs to the collecting line for the gas, which emerges from the upper opening, while on the lower end of the retort is fastened a coke cooler, whose walls can be cooled with air supplied for the drying of the combustibles or with water, which is supplied for the steam generation.

Cyclone oil shale retorting concept. [Use it all retorting process

Energy Technology Data Exchange (ETDEWEB)

Harak, A.E.; Little, W.E.; Faulders, C.R.

1984-04-01

A new concept for above-ground retorting of oil shale was disclosed by A.E. Harak in US Patent No. 4,340,463, dated July 20, 1982, and assigned to the US Department of Energy. This patent titled System for Utilizing Oil Shale Fines, describes a process wherein oil shale fines of one-half inch diameter and less are pyrolyzed in an entrained-flow reactor using hot gas from a cyclone combustor. Spent shale and supplemental fuel are burned at slagging conditions in this combustor. Because of fines utilization, the designation Use It All Retorting Process (UIARP) has been adopted. A preliminary process engineering design of the UIARP, analytical tests on six samples of raw oil shale, and a preliminary technical and economic evaluation of the process were performed. The results of these investigations are summarized in this report. The patent description is included. It was concluded that such changes as deleting air preheating in the slag quench and replacing the condenser with a quench-oil scrubber are recognized as being essential. The addition of an entrained flow raw shale preheater ahead of the cyclone retort is probably required, but final acceptance is felt to be contingent on some verification that adequate reaction time cannot be obtained with only the cyclone, or possibly some other twin-cyclone configuration. Sufficient raw shale preheating could probably be done more simply in another manner, perhaps in a screw conveyor shale transporting system. Results of the technical and economic evaluations of Jacobs Engineering indicate that further investigation of the UIARP is definitely worthwhile. The projected capital and operating costs are competitive with costs of other processes as long as electric power generation and sales are part of the processing facility.

Coal Combustion Residual Beneficial Use Evaluation: Fly Ash Concrete and FGD Gypsum Wallboard

Science.gov (United States)

This page contains documents related to the evaluation of coal combustion residual beneficial use of fly ash concrete and FGD gypsum wallboard including the evaluation itself and the accompanying appendices

Nitrogen fixation by legumes in retorted shale

Energy Technology Data Exchange (ETDEWEB)

Hersman, L E; Molitoris, E; Klein, D A

1981-01-01

Although a soil-shale mixture was employed as the growth medium in this experiment, the results presentd are applicable to the proposed method of disposal mentioned earlier. Under field conditions, when covering the retorted shale with topsoil, some mixing of these materials might occur in the plant root region. In addition, it has been demonstrated that buried shale negatively affects enzyme activities in overburden surface soil. The occurrence of either of those events could affect symbiotic N/sub 2/ fixation in a manner similar to that reported in this paper. Researchers conclude that due to the varied effects of retorted shale on the legumes tested, further evaluation of other legumes may be necessary. Additional research would be required to determine which legumes have potential use for reclamation of retorted shale.

Retort

Energy Technology Data Exchange (ETDEWEB)

Schultz, E L

1928-11-22

A retort is described for gasifying coal, shale, lignite, and other organic substances, wherein the material is supplied from a hopper, as a film past a centrally heated chamber by means of a tier of overlapping rings provided with a spiral or screw edging. The rings are attached to an outer shell to which is given a rotary and a reciprocatory motion. The gas outlets are provided with open liquid seals and the spent material is delivered to a rotary water trough from whence it is removed by means of a scraper baffle.

Ectomycorrhizal community structure and function in relation to forest residue harvesting and wood ash applications

Energy Technology Data Exchange (ETDEWEB)

Mahmood, Shahid

2000-05-01

Ectomycorrhizal fungi form symbiotic associations with tree roots and assist in nutrient-uptake and -cycling in forest ecosystems, thereby constituting a most significant part of the microbial community. The aims of the studies described in this thesis were to evaluate the potential of DNA-based molecular methods in below-ground ectomycorrhizal community studies and to investigate changes in ectomycorrhizal communities on spruce roots in sites with different N deposition, and in sites subjected to harvesting of forest residues or application of wood ash. The ability of selected ectomycorrhizal fungi to mobilise nutrients from wood ash and to colonise root systems in the presence and absence of ash was also studied. In total 39 ectomycorrhizal species were detected in the experimental forests located in southern Sweden. At each site five to six species colonised around 60% of the root tips. The dominant species, common to the sites, were Tylospora fibrillosa, Thelephora terrestris and Cenococcum geophilum. Differences between two sites with differing levels of N deposition suggested that community structure may be influenced by N deposition, although site history, location and degree of isolation may also influence species composition. Repeated harvesting of forest residues reduced numbers of mycorrhizal roots in the humus layer to approximately 50% of that in control plots but no shift in the ectomycorrhizal community could be detected. At another site, application of granulated wood ash induced a shift in ectomycorrhizal community structure and three ectomycorrhizal fungi ('ash fungi') were found to colonise ash granules. Two 'ash fungi' showed a superior ability to solubilise stabilised wood ash in laboratory experiments compared to other ectomycorrhizal isolates from the same site. In laboratory microcosms containing intact mycorrhizal mycelia, colonisation of wood ash patches by one 'ash fungus' was good whereas colonisation by

Ectomycorrhizal community structure and function in relation to forest residue harvesting and wood ash applications

International Nuclear Information System (INIS)

Mahmood, Shahid

2000-05-01

Ectomycorrhizal fungi form symbiotic associations with tree roots and assist in nutrient-uptake and -cycling in forest ecosystems, thereby constituting a most significant part of the microbial community. The aims of the studies described in this thesis were to evaluate the potential of DNA-based molecular methods in below-ground ectomycorrhizal community studies and to investigate changes in ectomycorrhizal communities on spruce roots in sites with different N deposition, and in sites subjected to harvesting of forest residues or application of wood ash. The ability of selected ectomycorrhizal fungi to mobilise nutrients from wood ash and to colonise root systems in the presence and absence of ash was also studied. In total 39 ectomycorrhizal species were detected in the experimental forests located in southern Sweden. At each site five to six species colonised around 60% of the root tips. The dominant species, common to the sites, were Tylospora fibrillosa, Thelephora terrestris and Cenococcum geophilum. Differences between two sites with differing levels of N deposition suggested that community structure may be influenced by N deposition, although site history, location and degree of isolation may also influence species composition. Repeated harvesting of forest residues reduced numbers of mycorrhizal roots in the humus layer to approximately 50% of that in control plots but no shift in the ectomycorrhizal community could be detected. At another site, application of granulated wood ash induced a shift in ectomycorrhizal community structure and three ectomycorrhizal fungi ('ash fungi') were found to colonise ash granules. Two 'ash fungi' showed a superior ability to solubilise stabilised wood ash in laboratory experiments compared to other ectomycorrhizal isolates from the same site. In laboratory microcosms containing intact mycorrhizal mycelia, colonisation of wood ash patches by one 'ash fungus' was good whereas colonisation by Piloderma croceum was poor. In a

A review on technologies for oil shale surface retort

International Nuclear Information System (INIS)

Pan, Y.; Zhang, X.; Liu, S.; Yang, S.A.; Ren, N.

2012-01-01

In recent years, with the shortage of oil resources and the continuous increase in oil prices, oil shale has seized much more attention. Oil shale is a kind of important unconventional oil and gas resources. Oil shale resources are plentiful according to the proven reserves in places. And shale oil is far richer than crude oil in the world. Technology processing can be divided into two categories: surface retorting and in-situ technology. The process and equipment of surface retorting are more mature, and are still up to now, the main way to produce shale oil from oil shale. According to the variations of the particle size, the surface retorting technologies of oil shale can be notified and classified into two categories such as lump shale process and particulate shale process. The lump shale processes introduced in this article include the Fushun retorting technology, the Kiviter technology and the Petrosix technology; the particulate processes include the Gloter technology, the LR technology, the Tosco-II technology, the ATP (Alberta Taciuk Process) technology and the Enefit-280 technology. After the thorough comparison of these technologies, we can notice that, this article aim is to show off that : the particulate process that is environmentally friendly, with its low cost and high economic returns characteristics, will be the major development trend; Combined technologies of surface retorting technology and other oil producing technology should be developed; the comprehensive utilization of oil shale should be considered during the development of surface retorting technology, meanwhile the process should be harmless to the environment. (author)

Carbon speciation in ash, residual waste and contaminated soil by thermal and chemical analyses.

Science.gov (United States)

Kumpiene, Jurate; Robinson, Ryan; Brännvall, Evelina; Nordmark, Désirée; Bjurström, Henrik; Andreas, Lale; Lagerkvist, Anders; Ecke, Holger

2011-01-01

Carbon in waste can occur as inorganic (IC), organic (OC) and elemental carbon (EC) each having distinct chemical properties and possible environmental effects. In this study, carbon speciation was performed using thermogravimetric analysis (TGA), chemical degradation tests and the standard total organic carbon (TOC) measurement procedures in three types of waste materials (bottom ash, residual waste and contaminated soil). Over 50% of the total carbon (TC) in all studied materials (72% in ash and residual waste, and 59% in soil) was biologically non-reactive or EC as determined by thermogravimetric analyses. The speciation of TOC by chemical degradation also showed a presence of a non-degradable C fraction in all materials (60% of TOC in ash, 30% in residual waste and 13% in soil), though in smaller amounts than those determined by TGA. In principle, chemical degradation method can give an indication of the presence of potentially inert C in various waste materials, while TGA is a more precise technique for C speciation, given that waste-specific method adjustments are made. The standard TOC measurement yields exaggerated estimates of organic carbon and may therefore overestimate the potential environmental impacts (e.g. landfill gas generation) of waste materials in a landfill environment. Copyright © 2010 Elsevier Ltd. All rights reserved.

Thermal treatment of stabilized air pollution control residues in a waste incinerator pilot plant. Part 2: Leaching characteristics of bottom ashes.

Science.gov (United States)

Baun, Dorthe L; Christensen, Thomas H; Bergfeldt, Brita; Vehlow, Jürgen; Mogensen, Erhardt P B

2004-02-01

With the perspective of generating only one solid residue from waste incineration, co-feeding of municipal solid waste and air pollution control residues stabilized by the Ferrox process was investigated in the TAMARA pilot plant incinerator as described in Bergfeldt et al. (Waste Management Research, 22, 49-57, 2004). This paper reports on leaching from the combined bottom ashes. Batch leaching test, pH-static leaching tests, availability tests and column leaching tests were used to characterize the leaching properties. The leaching properties are key information in the context of reuse in construction or in landfilling of the combined residue. In general, the combined bottom ashes had leaching characteristics similar to the reference bottom ash, which contained no APC residue. However, As and Pb showed slightly elevated leaching from the combined bottom ashes, while Cr showed less leaching. The investigated combined bottom ashes had contents of metals comparable to what is expected at steady state after continuous co-feeding of APC residues. Only Cd and Pb were partly volatilized (30-40%) during the incineration process and thus the combined bottom ashes had lower contents of Cd and Pb than expected at steady state. Furthermore, a major loss of Hg was, not surprisingly, seen and co-feeding of Ferrox-products together with municipal solid waste will require dedicated removal of Hg in the flue gas to prevent a build up of Hg in the system. In spite of this, a combined single solid residue from waste incineration seems to be a significant environmental improvement to current technology.

Improvements in retorts for the processing of coal, oil shale and like material

Energy Technology Data Exchange (ETDEWEB)

Honyburn, A G; James, G L.D.

1931-05-28

Improvements in retorts of the kind described consist of means wherein the material to be retorted is fed through the retort in a continuous manner by means of horizontally revolving star wheels whereby the material is prevented from jambing due to expansion. Coking of the material en masse during the intumescence period is prevented, and the material is maintained in contact with the walls of the retort ensuring uniform heating of the mass.

Retort process modelling for Indian traditional foods.

Science.gov (United States)

Gokhale, S V; Lele, S S

2014-11-01

Indian traditional staple and snack food is typically a heterogeneous recipe that incorporates varieties of vegetables, lentils and other ingredients. Modelling the retorting process of multilayer pouch packed Indian food was achieved using lumped-parameter approach. A unified model is proposed to estimate cold point temperature. Initial process conditions, retort temperature and % solid content were the significantly affecting independent variables. A model was developed using combination of vegetable solids and water, which was then validated using four traditional Indian vegetarian products: Pulav (steamed rice with vegetables), Sambar (south Indian style curry containing mixed vegetables and lentils), Gajar Halawa (carrot based sweet product) and Upama (wheat based snack product). The predicted and experimental values of temperature profile matched with ±10 % error which is a good match considering the food was a multi component system. Thus the model will be useful as a tool to reduce number of trials required to optimize retorting of various Indian traditional vegetarian foods.

On possibilities to decrease influence of oxidation processes on oil yield at oil shale retorting

International Nuclear Information System (INIS)

Yefimov, V.; Loeoeper, R.; Doilov, S.; Kundel, H.

1993-01-01

At the present technical level retorting is carried out so that an increase in specific air consumption results in an increase of oxygen ingress into the semi coking shaft. At the same time a direct relationship between the degree of volatiles pyrolysis and specific air consumption was observed. This regularity enables to assume that within the reaction volume there occurs most likely the thermo oxidative pyrolysis of volatile products, not the oxidation of oil shale as it is considered traditionally. The main source of oxygen ingress ed into the semi coking shaft at processing oil shale in retorts is the process of spent shale. This process is not fully elaborated for utilization in commercial scale and can not be arranged so that the ingress of oxygen into the smacking chamber could be eliminated. In case of a slower semi coke gasification process and reduced specific air consumption for gasification the absolute amount of oxygen ingress ed into the semi coking shaft also decreases. One of the efficient methods to decrease specific air consumption is to build furnaces into the semi coking chamber to obtain additional amount of heat carrier by combusting generator gas. The maximum effect is reached when steam-and-air blow is completely replaced by recycle gas: specific air consumption is reduced whereas recycle gas is deoxygenated in the cooling zone while passing through spent shale bed which has the temperature of about 500 deg C. Another possible source of oxygen to the semi coking shaft with heat carrier is production of flue gases by combusting recycle gas in burners built in retorts. We consider the recycle gas employed upon processing oil shale in retorts hardly to be an appreciable source of the oxygen ingress into the semi coking shaft. Additional amounts of residual oxygen containing in recycle gas fed into both cooling zone and furnaces are practically totally consumed at gas combusting and passing across the bed of semi coke heated up to approximately

Fly ash classification efficiency of electrostatic precipitators in fluidized bed combustion of peat, wood, and forest residues.

Science.gov (United States)

Ohenoja, Katja; Körkkö, Mika; Wigren, Valter; Österbacka, Jan; Illikainen, Mirja

2018-01-15

The increasing use of biomasses in the production of electricity and heat results in an increased amount of burning residue, fly ash which disposal is becoming more and more restricted and expensive. Therefore, there is a great interest in utilizing fly ashes instead of just disposing of it. This study aimed to establish whether the utilization of fly ash from the fluidized bed combustion of peat, wood, and forest residues can be improved by electrostatic precipitator separation of sulfate, chloride, and some detrimental metals. Classification selectivity calculations of electrostatic precipitators for three different fuel mixtures from two different power plants were performed by using Nelson's and Karnis's selectivity indices. Results showed that all fly ashes behaved similarly in the electrostatic separation process SiO 2 resulted in coarse fractions with Nelson's selectivity of 0.2 or more, while sulfate, chloride, and the studied detrimental metals (arsenic, cadmium, and lead) enriched into fine fractions with varying selectivity from 0.2 to 0.65. Overall, the results of this study suggest that it is possible to improve the utilization potential of fly ashes from fluidized bed combustion in concrete, fertilizer, and earth construction applications by using electrostatic precipitators for the fractionating of fly ashes in addition to their initial function of collecting fly ash particles from flue gases. The separation of the finer fractions (ESP 2 and 3) from ESP 1 field fly ash is recommended. Copyright © 2017 Elsevier Ltd. All rights reserved.

Gas retorts: gas manufacture, process for distillation, destructive

Energy Technology Data Exchange (ETDEWEB)

Bell, J

1874-05-23

In apparatus for distilling shale, coal, etc. for making oil and gas, tubular retorts are supported horizontally in a chamber by plates from a brick setting and are heated partly by jets of gas from a pipe supplied through a cock from a gas holder, and partly by the waste gases from a furnace, which heats gas retorts placed in a chamber, air being supplied beneath the grate by a fan.

The mechanisms of edge wicking in retortable paperboard

OpenAIRE

Tufvesson, Helena

2006-01-01

This thesis reports on an investigation of the mechanisms of edge wicking in retortable paperboard. Retortable board is used for packaging preserved food, a process which requires that the package and its contents be sterilised by exposure to high temperature steam for up to three hours. The board used must thus have higher water repellence than traditional liquid packaging. Water vapour that condenses on the cut edges on the outside of the board causes particular concern. The paperboards stu...

Wood ash residue causes a mixture of growth promotion and toxicity in Lemna minor.

Science.gov (United States)

Jagodzinski, Lucas S; O'Donoghue, Marian T; Heffernan, Liam B; van Pelt, Frank N A M; O'Halloran, John; Jansen, Marcel A K

2018-06-01

The use of wood as a sustainable biofuel results in the generation of residual wood ash. The ash contains high amounts of plant macronutrients such as phosphorus, potassium, calcium as well as several micronutrients. To explore the potential use of wood ash as a fertiliser, the growth enhancing properties of Sitka spruce (Picea sitchensis Bong.) wood ash were contrasted with the potential toxic action, using common duckweed (Lemna minor L.) as a model test species. The growth of L. minor exposed to wood bottom and fly ash solids and corresponding leachates was assessed in ultra-oligotrophic and eutrophic media. Ash solids and leachates were also tested as neutralized preparations. Suspended ash solids promoted L. minor growth up to concentrations of 2.5-5g/L. Leachates promoted growth up to 10g ash equivalents per litre, but for bottom ash only. Beneficial effects of wood ash were most pronounced on ultra-oligotrophic medium. However, on such nutrient-deficient medium severe inhibition of L. minor biomass and frond growth was observed at relatively low concentrations of fly ash (EC 50 =14g/L). On standard, eutrophic medium, higher concentrations of fly ash (EC 50 =21g/L), or neutralized fly ash (EC 50 =37g/L) were required to impede growth. Bottom ash, or neutralized bottom ash retarded growth at concentrations of 51g/L and 74g/L (EC 50 ), respectively, in eutrophic medium. It appears that phytotoxicity is due to the elemental composition of the ash, its alkaline character, and possible interactions between these two properties. Growth promotion was due to the substantial content of plant nutrients. This study underlines the importance of the receiving environment (nutrient status and pH) in determining the balance between toxicity and growth promotion, and shows that the margin between growth promoting and toxicity inducing concentrations can be enlarged through ash neutralization. Copyright © 2017 Elsevier B.V. All rights reserved.

Specific features of kukersite processing in laboratory-scale and commercial retorts

International Nuclear Information System (INIS)

Yefimov, V.; Kundel, H.

1991-01-01

The yield and properties of shale oil produced by semi coking oil shale in retorts of different design depend to a great extent on the conditions of volatiles evacuation from the high temperature zone. In externally heated laboratory retorts, where oil vapours reside in the reaction zone for a relatively long period undergoing moderate cracking, no maximum oil yields are attained. The higher the organic matter content in the oil shale, the higher is the partial pressure of the oil vapours in the retort and hence the rate of their removal from the retorting zone, resulting in increased shale oil yields and lower specific yield of hydrogen in the retort off-gases. replacing the external heating mode with direct heating by a gaseous heat carrier (carbon dioxide, in particular) leads to a considerable moderation of the volatiles pyrolysis. As a result, the shale oil produced has a higher density and molecular mass, a lower calorific value and a higher content of phenols. The presence of water vapours in the heat carrier gas also has a positive effect upon the yield of shale oil and phenols. The properties of the oil and gas produced by semi coking kukersite in the presence of free calcium oxide are similar to those of cracked products. The presence of free calcium oxide has the same effect as higher temperatures or longer residence time of the volatiles in the retorting zone: it leads to reduced yields of shale oil and phenols, to a lower density of the oil and higher yields of hydrogen and gaseous hydrocarbons. This should be taken into consideration on evaluating the efficiency of semi coking oil shale in the retorts with solid heat carrier, which contains free calcium oxide

Solid residues

International Nuclear Information System (INIS)

Mulder, E.; Duin, P.J. van; Grootenboer, G.J.

1995-01-01

A summary is presented of the many investigations that have been done on solid residues of atmospheric fluid bed combustion (AFBC). These residues are bed ash, cyclone ash and bag filter ash. Physical and chemical properties are discussed and then the various uses of residues (in fillers, bricks, gravel, and for recovery of aluminium) are summarised. Toxicological properties of fly ash and stack ash are discussed as are risks of pneumoconiosis for workers handling fly ash, and contamination of water by ashes. On the basis of present information it is concluded that risks to public health from exposure to emissions of coal fly ash from AFBC appear small or negligible as are health risk to workers in the coal fly ash processing industry. 35 refs., 5 figs., 12 tabs

Retorting conditions affect palatability and physical characteristics of canned cat food

NARCIS (Netherlands)

Hagen-Plantinga, E.A.; Orlanes, D.F.; Bosch, G.; Hendriks, W.H.; Poel, van der A.F.B.

2017-01-01

The effects of different temperature and time conditions during retorting of canned cat food on physicochemical characteristics and palatability were examined. For this purpose, lacquer cans containing an unprocessed loaf-type commercial cat food were heated in a pressurised retorting system at

Bioaccessibility and health risk of heavy metals in ash from the incineration of different e-waste residues.

Science.gov (United States)

Tao, Xiao-Qing; Shen, Dong-Sheng; Shentu, Jia-Li; Long, Yu-Yang; Feng, Yi-Jian; Shen, Chen-Chao

2015-03-01

Ash from incinerated e-waste dismantling residues (EDR) may cause significant health risks to people through ingestion, inhalation, and dermal contact exposure pathways. Ashes of four classified e-waste types generated by an incineration plant in Zhejiang, China were collected. Total contents and the bioaccessibilities of Cd, Cu, Ni, Pb, and Zn in ashes were measured to provide crucial information to evaluate the health risks for incinerator workers and children living in vicinity. Compared to raw e-waste in mixture, ash was metal-enriched by category incinerated. However, the physiologically based extraction test (PBET) indicates the bioaccessibilities of Ni, Pb, and Zn were less than 50 %. Obviously, bioaccessibilities need to be considered in noncancer risk estimate. Total and PBET-extractable contents of metal, except for Pb, were significantly correlated with the pH of the ash. Noncancer risks of ash from different incinerator parts decreased in the order bag filter ash (BFA) > cyclone separator ash (CFA) > bottom ash (BA). The hazard quotient for exposure to ash were decreased as ingestion > dermal contact > inhalation. Pb in ingested ash dominated (>80 %) noncancer risks, and children had high chronic risks from Pb (hazard index >10). Carcinogenic risks from exposure to ash were under the acceptable level (incinerated ash are made.

The influence of electrodialytic remediation on dioxin (PCDD/PCDF) levels in fly ash and air pollution control residues.

Science.gov (United States)

Dias-Ferreira, Celia; Kirkelund, Gunvor M; Jensen, Pernille E

2016-04-01

Fly ash and Air Pollution Control (APC) residues collected from three municipal solid waste incinerators in Denmark and Greenland were treated by electrodialytic remediation at pilot scale for 8-10 h. This work presents for the first time the effect of electrodialytic treatment on polychlorinated dibenzo-p-dioxins (PCDD) and polychlorinated dibenzofurans (PCDF), and how these levels impact on the valorization options for fly ash and APC residue. PCDD/PCDF levels in the original residues ranged between 4.85 and 197 ng g(-1), being higher for the electrostatic precipitator fly ash. The toxic equivalent (TEQ) varied ten fold, ranging 0.18-2.0 ng g(-1) I-TEQ, with penta and hexa-homologs being most significant for toxicity. After the electrodialytic treatment PCDD/PCDF levels increased in the residues (between 1.4 and 2.0 times). This does not mean PCDD/PCDF were synthesized, but else that soluble materials dissolve, leaving behind the non-water soluble compounds, such as PCDD/PCDF. According to the Basel Convention, PCDD/PCDF levels in these materials is low (residue could eventually be valorized, for instance as construction material, provided end-of-waste criteria are set and that a risk assessment of individual options is carried out, including the end-of-life stage when the materials become waste again. Copyright © 2016 Elsevier Ltd. All rights reserved.

Use of fly ash, phosphogypsum and red mud as a liner material for the disposal of hazardous zinc leach residue waste.

Science.gov (United States)

Coruh, Semra; Ergun, Osman Nuri

2010-01-15

Increasing amounts of residues and waste materials coming from industrial activities in different processes have become an increasingly urgent problem for the future. The release of large quantities of heavy metals into the environment has resulted in a number of environmental problems. The present study investigated the safe disposal of the zinc leach residue waste using industrial residues such as fly ash, phosphogypsum and red mud. In the study, leachability of heavy metals from the zinc leach residue has been evaluated by mine water leaching procedure (MWLP) and toxicity characteristic leaching procedure (TCLP). Zinc removal from leachate was studied using fly ash, phosphogypsum and red mud. The adsorption capacities and adsorption efficiencies were determined. The adsorption rate data was analyzed according to the pseudo-second-order kinetic, Elovich kinetic and intra-particle diffusion kinetic models. The pseudo-second-order kinetic was the best fit kinetic model for the experimental data. The results show that addition of fly ash, phosphogypsum and red mud to the zinc leach residue drastically reduces the heavy metal content in the leachate and could be used as liner materials.

The study of heat penetration of kimchi soup on stationary and rotary retorts.

Science.gov (United States)

Cho, Won-Il; Park, Eun-Ji; Cheon, Hee Soon; Chung, Myong-Soo

2015-03-01

The aim of this study was to determine the heat-penetration characteristics using stationary and rotary retorts to manufacture Kimchi soup. Both heat-penetration tests and computer simulation based on mathematical modeling were performed. The sterility was measured at five different positions in the pouch. The results revealed only a small deviation of F 0 among the different positions, and the rate of heat transfer was increased by rotation of the retort. The thermal processing of retort-pouched Kimchi soup was analyzed mathematically using a finite-element model, and optimum models for predicting the time course of the temperature and F 0 were developed. The mathematical models could accurately predict the actual heat penetration of retort-pouched Kimchi soup. The average deviation of the temperature between the experimental and mathematical predicted model was 2.46% (R(2)=0.975). The changes in nodal temperature and F 0 caused by microbial inactivation in the finite-element model predicted using the NISA program were very similar to that of the experimental data of for the retorted Kimchi soup during sterilization with rotary retorts. The correlation coefficient between the simulation using the NISA program and the experimental data was very high, at 99%.

Instrumentation and operational plan for geokinetics retort No. 22

Energy Technology Data Exchange (ETDEWEB)

Parrish, R.L.; Hommert, P.J.

1980-04-01

This report outlines the general plan for the instrumentation and technical direction of a horizontal in siti retorting experiment to be conducted at the Geokinetics, Inc. field site in Uintah County, Utah. Bed preparation has been accomplished by Geokinetics by blasting the retort zone with explosives emplaced in wells drilled from the surface. Downhole instrumentation will consist of approx. 300 thermocouples and 28 combustion gas sampling ports to monitor the movement of the reaction front during the retorting process. Surface instrumentation will provide measurements of flow rates, gas composition, liquid products and other process parameters to monitor the overall operation of the process. The operational plan includes provision for data interpretation and real time material balance calculations in the field, including an evaluation of the effect on processing rates and oil yield due to the use of recycled combusted off gases and changes in rate of injection of inlet gases.

Method of distillation of shale. [addition of water to vertical retort

Energy Technology Data Exchange (ETDEWEB)

Hultman, G H

1915-09-11

The method is characterized by adding water, finely distributed, to the warm shale being distilled in a vertical retort. By this procedure steam is generated which will drive out and protect the distilled oil vapors. The adding of finely distributed water, already mentioned, takes place in special chambers under the retort.

Persistent free radicals, heavy metals and PAHs generated in particulate soot emissions and residue ash from controlled combustion of common types of plastic

International Nuclear Information System (INIS)

Valavanidis, Athanasios; Iliopoulos, Nikiforos; Gotsis, George; Fiotakis, Konstantinos

2008-01-01

The production and use of polymeric materials worldwide has reached levels of 150 million tonnes per year, and the majority of plastic materials are discarded in waste landfills where are burned generating toxic emissions. In the present study we conducted laboratory experiments for batch combustion/burning of commercial polymeric materials, simulating conditions of open fire combustion, with the purpose to analyze their emissions for chemical characteristics of toxicological importance. We used common types of plastic materials: poly(vinyl chloride) (PVC), low and high density poly(ethylene) (LDPE, HDPE), poly(styrene) (PS), poly(propylene) (PP) and poly(ethylene terephthalate) (PET). Samples of particulate smoke (soot) collected on filters and residue solid ash produced by controlled burning conditions at 600-750 deg. C are used for analysis. Emissions of particulate matter, persistent free radicals embedded in the carbonaceous polymeric matrix, heavy metals, other elements and PAHs were determined in both types of samples. Results showed that all plastics burned easily generating charred residue solid ash and black airborne particulate smoke. Persistent carbon- and oxygen-centered radicals, known for their toxic effects in inhalable airborne particles, were detected in both particulate smoke emissions and residue solid ash. Concentrations of heavy metals and other elements (determined by Inductively Coupled Plasma Emission Spectrometry, ICP, method) were measured in the airborne soot and residue ash. Toxic heavy metals, such as Pb, Zn, Cr, Ni, and Cd were relatively at were found at low concentrations. High concentrations were found for some lithophilic elements, such as Na, Ca, Mg, Si and Al in particulate soot and residue solid ash. Measurements of PAHs showed that low molecular weight PAHs were at higher concentrations in the airborne particulate soot than in the residue solid ash for all types of plastic. Higher-ringed PAHs were detected at higher

Persistent free radicals, heavy metals and PAHs generated in particulate soot emissions and residue ash from controlled combustion of common types of plastic.

Science.gov (United States)

Valavanidis, Athanasios; Iliopoulos, Nikiforos; Gotsis, George; Fiotakis, Konstantinos

2008-08-15

The production and use of polymeric materials worldwide has reached levels of 150 million tonnes per year, and the majority of plastic materials are discarded in waste landfills where are burned generating toxic emissions. In the present study we conducted laboratory experiments for batch combustion/burning of commercial polymeric materials, simulating conditions of open fire combustion, with the purpose to analyze their emissions for chemical characteristics of toxicological importance. We used common types of plastic materials: poly(vinyl chloride) (PVC), low and high density poly(ethylene) (LDPE, HDPE), poly(styrene) (PS), poly(propylene) (PP) and poly(ethylene terephthalate) (PET). Samples of particulate smoke (soot) collected on filters and residue solid ash produced by controlled burning conditions at 600-750 degrees C are used for analysis. Emissions of particulate matter, persistent free radicals embedded in the carbonaceous polymeric matrix, heavy metals, other elements and PAHs were determined in both types of samples. Results showed that all plastics burned easily generating charred residue solid ash and black airborne particulate smoke. Persistent carbon- and oxygen-centered radicals, known for their toxic effects in inhalable airborne particles, were detected in both particulate smoke emissions and residue solid ash. Concentrations of heavy metals and other elements (determined by Inductively Coupled Plasma Emission Spectrometry, ICP, method) were measured in the airborne soot and residue ash. Toxic heavy metals, such as Pb, Zn, Cr, Ni, and Cd were relatively at were found at low concentrations. High concentrations were found for some lithophilic elements, such as Na, Ca, Mg, Si and Al in particulate soot and residue solid ash. Measurements of PAHs showed that low molecular weight PAHs were at higher concentrations in the airborne particulate soot than in the residue solid ash for all types of plastic. Higher-ringed PAHs were detected at higher

Furnaces, retorts, and apparatus for distilling bituminous shale

Energy Technology Data Exchange (ETDEWEB)

Germain-Clergault, M

1857-06-20

The furnace is a rectangle 4.90 m by 4.80 m; it is divided into two distinct compartments by a partition wall which carries on top a circular arch of 30 cms bend, covering a passage 2 m high under the keystone and 2 m long and carrying also 14 vertical retorts, which are charged on top, and discharged at the bottom into the passage. There are seven (retorts) in each compartment and they are symmetrically arranged. The hearths are parallel to the compartments; and they form four fires, a wall separating them two by two.

Distillation, destructive: gas retorts

Energy Technology Data Exchange (ETDEWEB)

Anderson, G; Buchanan, J

1872-06-12

Retorts used in the distillation of coal, cannel, shale, or other minerals are discharged by means of a joint metal bar or a chain inserted prior to or with the charge, and fitted with a plate or series of plates preferably with the back plate the largest. The rod or chain is formed with a hook, loop, or coupling for withdrawal, preferably by a steam windlass running on rails.

Residual Ash Formation during Suspension-Firing of Biomass

DEFF Research Database (Denmark)

Damø, Anne Juul; Jappe Frandsen, Flemming; Jensen, Peter Arendt

2014-01-01

Through 50+ years, high quality research has been conducted in order to characterize ash and deposit formation in utility boilers fired with coal, biomass and waste fractions. The basic mechanism of fly ash formation in suspension fired coal boilers is well described, documented and may even...... be modeled relatively precisely. Concerning fly ash formation from biomass or waste fractions, the situation is not nearly as good. Lots of data are available from campaigns where different ash fractions, including sometimes also in-situ ash, have been collected and analyzed chemically and for particle size...... distribution. Thus, there is a good flair of the chemistry of fly ash formed in plants fired with biomass or waste fractions, either alone, or in conjunction with coal. But data on dedicated studies of the physical size development of fly ash, are almost non-existing for biomasses and waste fractions...

Evaluation of the Performance and Microstructure of Ecofriendly Construction Bricks Made with Fly Ash and Residual Rice Husk Ash

Directory of Open Access Journals (Sweden)

Chao-Lung Hwang

2015-01-01

Full Text Available This research presents the engineering performance and the microstructural characterization of ecofriendly construction bricks that were produced using a binder material made from a mixture of class-F fly ash (FA and residual rice husk ash (RHA. Unground rice husk ash (URHA was used as a partial fine aggregate substitute (0–40%. The solid bricks of 220 × 105 × 60 mm in size were prepared by mixing FA and RHA with an alkaline solution and fine aggregates, formed by compressing the mixture in a steel mold under 35 MPa of forming pressure, and then cured at 35°C and 50% relative humidity until the required testing ages. The tests of compressive strength, water absorption, and bulk density were conducted in accordance with relevant Vietnamese standards in order to estimate the effect of the URHA content on the engineering performance of the hardened bricks. Scanning electron microscopy (SEM, X-ray diffraction (XRD, and Fourier transform infrared spectroscopy (FTIR were performed to determine the microstructure and the phase composition of the brick samples. The results show that properties of these bricks conformed to relevant Vietnamese standards. Therefore, FA and RHA are potential candidate materials for producing ecofriendly construction bricks using geopolymerization technology.

High temperature co-treatment of bottom ash and stabilized fly ashes from waste incineration

DEFF Research Database (Denmark)

Sørensen, Mette Abildgaard; Mogensen, E.P.B.; Lundtorp, Kasper

2001-01-01

Bottom ashes from two Danish municipal solid waste incineration plants were heated at 900 degreesC with iron oxide stabilized air pollution control residues at actual mass flow ratios (9:1), simulating a treating method for the residues. The two residues were cotreated, producing one combined...... ashes. The process, thus, fixates the metals in the solid residues without altering the leaching properties of the bottom ash too significantly. (C) 2001 Elsevier Science Ltd. All rights reserved....... stream that may be utilized as a secondary road construction material. Scanning electron microscope analysis and grain size distribution analysis indicated that sintering of the particles did not occur. Batch leaching tests at liquid/solid 10 I/kg at a range of pH-values (6-10) quantified with respect...

Development of charcoal retort pilot plant in Zambia. African Energy Programme research report series no. 4

International Nuclear Information System (INIS)

Yamba, F.D.

1988-01-01

The technical report discusses the theoretical and experimental work which has been undertaken in the design, construction, testing and evaluation of charcoal retort model prototypes. Optimum operating conditions have been established at an initial temperature of 350 deg. C and stabilisation time of 5 hours. From the technical point of view, the project is viable since as per set objectives, charcoal is being produced at a higher conversion efficiency of around 40% and the by-products in the form of pyroligenous liquor and tar are recovered. As expected, the analysis shows that the model is uneconomic since the technological price of the products exceeds that of the selling price of products. However, the increase in the size of the retort chamber by eighteen renders the prototype economically viable. The report also discusses further work such as continuation of the testing of the retort to establish concretely the optimum operating conditions, determination of the reliability and durability of the retort and evaluation of the quality of charcoal produced, which has been recommended. Based on the results from the retort model and preliminary financial analysis, an economic analysis on the value of by-products from wood distillation is undertaken. The analysis shows that there is a reasonable market of by-products, (acetone, methanol and acetic acid) to warrant processing of the pyroligenous liquor, and subsequent setting up of a small scale distillation plant. Using the same results from the retort model, a charcoal retort plant with a 10m 3 retort chamber capacity is designed. In the design of the retort chamber, various considerations are undertaken such as stress calculations of the retort chamber on the support legs, furnace, piping and distribution chamber design, and their associated heat losses. Basing on the amount of heat required to complete the carbonisation process and heat losses from the system, a suitable furnace size and air blower are selected

Principal chemical properties of artificial soil composed of fly ash and furfural residue

Energy Technology Data Exchange (ETDEWEB)

Feng, Y.J.; Li, F.; Wang, X.L.; Liu, X.M.; Zhang, L.N. [Shandong Agricultural University, Tai An (China). College of Resources & Environments

2006-10-15

To solve soil shortage in reclaiming subsided land of coal mines, the principal chemical properties of artificial soil formed by mixing organic furfural residue and inorganic fly ash were examined. The results indicated that the artificial soil was suitable for agriculture use after irrigation and desalination, the available nutrients in the artificial soil could satisfy the growth demand of plants, and the pH tended to the neutrality.

Retorting conditions affect palatability and physical characteristics of canned cat food.

Science.gov (United States)

Hagen-Plantinga, Esther A; Orlanes, Denmark F; Bosch, Guido; Hendriks, Wouter H; van der Poel, Antonius F B

2017-01-01

The effects of different temperature and time conditions during retorting of canned cat food on physicochemical characteristics and palatability were examined. For this purpose, lacquer cans containing an unprocessed loaf-type commercial cat food were heated in a pressurised retorting system at three specified temperature-time profiles (113°C/232 min, 120°C/103 min and 127°C/60 min) to equal a similar lethality ( F 0 value = 30). Physicochemical properties (viscosity, texture, particle size, pH) were determined, and a 10 d three-bowl palatability test was performed with ten European shorthair cats. Retorting at 113°C/232 min resulted in differences in all the physical parameters examined ( particle size). Significant pH differences were observed (6·53, 6·63 and 6·66 for T113/232, 120 and 127°C, respectively). Preference ratios were 0·38, 0·31 and 0·31 for T113/232, 120 and 127°C, respectively ( P  = 0·067). It can be concluded that different retorting temperature-time profiles with equal F 0 value significantly affect physical characteristics and tended to affect palatability of moist cat food.

Glass-ceramic from mixtures of bottom ash and fly ash.

Science.gov (United States)

Vu, Dinh Hieu; Wang, Kuen-Sheng; Chen, Jung-Hsing; Nam, Bui Xuan; Bac, Bui Hoang

2012-12-01

Along with the gradually increasing yield of the residues, appropriate management and treatment of the residues have become an urgent environmental protection problem. This work investigated the preparation of a glass-ceramic from a mixture of bottom ash and fly ash by petrurgic method. The nucleation and crystallization kinetics of the new glass-ceramic can be obtained by melting the mixture of 80% bottom ash and 20% fly ash at 950 °C, which was then cooled in the furnace for 1h. Major minerals forming in the glass-ceramics mainly are gehlenite (Ca(2)Al(2)SiO(7)) & akermanite (Ca(2)MgSiO(7)) and wollastonite (CaSiO(3)). In addition, regarding chemical/mechanical properties, the chemical resistance showing durability, and the leaching concentration of heavy metals confirmed the possibility of engineering and construction applications of the most superior glass-ceramic product. Finally, petrurgic method of a mixture of bottom ash and fly ash at 950 °C represents a simple, inexpensive, and energy saving method compared with the conventional heat treatment. Copyright © 2012 Elsevier Ltd. All rights reserved.

Brazing retort manifold design concept may minimize air contamination and enhance uniform gas flow

Science.gov (United States)

Ruppe, E. P.

1966-01-01

Brazing retort manifold minimizes air contamination, prevents gas entrapment during purging, and provides uniform gas flow into the retort bell. The manifold is easily cleaned and turbulence within the bell is minimized because all manifold construction lies outside the main enclosure.

Application of dry separative methods for decreasing content the residues unburned coal and separation Fe from black coal flies ash

Directory of Open Access Journals (Sweden)

František Kaľavský

2008-06-01

Full Text Available Main obstacle using of fly ashes in building, that is its main consumer, is the residue of unburned coal; it is expressed of loss onignition - LOI. In present, the valid STN and EU standard limits the content of LOI to 3 – 5 %, in national conditions maximum 7 %.Application of processing technologies also has to assure utilization of fly ash that provides a possibility of complex utilizationof individual products obtained by modification.By means of corona separation, based on different conductivity of individual fly ash elements, it is possible to separate unburnedcoal particles. The fly ash sample from black coal burning in melting boiler that was deposited on fly ash deposit, content of LOIof dielectric particle 6,45 % at 61 % weight yield was achieved. In the samples taken from dry taking of fly ash the non-conductingproduct contained 7,72 % of LOI at 73 % of weight yield.

Vertical retorts for distilling, carbonizing, roasting, etc

Energy Technology Data Exchange (ETDEWEB)

Walker, H R.L.; Bates, W R

1917-11-17

In a continuously operated vertical retort for destructive distillation or roasting the combination of an annular internally and externally heated construction with an annular plunger adapted to compress and assist the travel of the charge and to aid in discharging material substantially is described.

Fly ash aggregates. Vliegaskunstgrind

Energy Technology Data Exchange (ETDEWEB)

1983-03-01

A study has been carried out into artificial aggregates made from fly ash, 'fly ash aggregates'. Attention has been drawn to the production of fly ash aggregates in the Netherlands as a way to obviate the need of disposal of fly ash. Typical process steps for the manufacturing of fly ash aggregates are the agglomeration and the bonding of fly ash particles. Agglomeration techniques are subdivided into agitation and compaction, bonding methods into sintering, hydrothermal and 'cold' bonding. In sintering no bonding agent is used. The fly ash particles are more or less welded together. Sintering in general is performed at a temperature higher than 900 deg C. In hydrothermal processes lime reacts with fly ash to a crystalline hydrate at temperatures between 100 and 250 deg C at saturated steam pressure. As a lime source not only lime as such, but also portland cement can be used. Cold bonding processes rely on reaction of fly ash with lime or cement at temperatures between 0 and 100 deg C. The pozzolanic properties of fly ash are used. Where cement is applied, this bonding agent itself contributes also to the strength development of the artificial aggregate. Besides the use of lime and cement, several processes are known which make use of lime containing wastes such as spray dry absorption desulfurization residues or fluid bed coal combustion residues. (In Dutch)

Lethality of Rendang packaged in multilayer retortable pouch with sterilization process

Science.gov (United States)

Praharasti, A. S.; Kusumaningrum, A.; Frediansyah, A.; Nurhikmat, A.; Khasanah, Y.; Suprapedi

2017-01-01

Retort Pouch had become a choice to preserve foods nowadays, besides the used of the can. Both had their own advantages, and Retort Pouch became more popular for the reason of cheaper and easier to recycle. General Method usually used to estimate the lethality of commercial heat sterilization process. Lethality value wa s used for evaluating the efficacy of the thermal process. This study aimed to find whether different layers of pouch materials affect the lethality value and to find differences lethality in two types of multilayer retort pouch, PET/Aluminum Foil/Nylon/RCPP and PET/Nylon/Modified Aluminum/CPP. The result showed that the different layer arrangement was resulted different Sterilization Value (SV). PET/Nylon/Modified Aluminum/CPP had better heat penetration, implied by the higher value of lethality. PET/Nylon/Modified Aluminum/CPP had the lethality value of 6,24 minutes, whereas the lethality value of PET/Aluminum Foil/Nylon/RCPP was 3,54 minutes.

Characterization of oil shale, isolated kerogen, and post-pyrolysis residues using advanced 13 solid-state nuclear magnetic resonance spectroscopy

Science.gov (United States)

Cao, Xiaoyan; Birdwell, Justin E.; Chappell, Mark A.; Li, Yuan; Pignatello, Joseph J.; Mao, Jingdong

2013-01-01

Characterization of oil shale kerogen and organic residues remaining in postpyrolysis spent shale is critical to the understanding of the oil generation process and approaches to dealing with issues related to spent shale. The chemical structure of organic matter in raw oil shale and spent shale samples was examined in this study using advanced solid-state 13C nuclear magnetic resonance (NMR) spectroscopy. Oil shale was collected from Mahogany zone outcrops in the Piceance Basin. Five samples were analyzed: (1) raw oil shale, (2) isolated kerogen, (3) oil shale extracted with chloroform, (4) oil shale retorted in an open system at 500°C to mimic surface retorting, and (5) oil shale retorted in a closed system at 360°C to simulate in-situ retorting. The NMR methods applied included quantitative direct polarization with magic-angle spinning at 13 kHz, cross polarization with total sideband suppression, dipolar dephasing, CHn selection, 13C chemical shift anisotropy filtering, and 1H-13C long-range recoupled dipolar dephasing. The NMR results showed that, relative to the raw oil shale, (1) bitumen extraction and kerogen isolation by demineralization removed some oxygen-containing and alkyl moieties; (2) unpyrolyzed samples had low aromatic condensation; (3) oil shale pyrolysis removed aliphatic moieties, leaving behind residues enriched in aromatic carbon; and (4) oil shale retorted in an open system at 500°C contained larger aromatic clusters and more protonated aromatic moieties than oil shale retorted in a closed system at 360°C, which contained more total aromatic carbon with a wide range of cluster sizes.

Time course of pulmonary burden in mice exposed to residual oil fly ash

OpenAIRE

Giovanna Marcella Cavalcante Carvalho; Lilian Katie Nagato; Sheila da Silva Fagundes; Flavia Brandão dos Santos; Andrea Surrage Calheiros; Olaf eMalm; Patricia Torres Bozza; Paulo Hilario Nascimento Saldiva; Debora Souza Faffe; Patricia Rieken Macedo Rocco; Walter Araujo Zin

2014-01-01

Residual oil fly ash (ROFA) is a common pollutant in areas where oil is burned. This particulate matter (PM) with a broad distribution of particle diameters can be inhaled by human beings and putatively damage their respiratory system. Although some studies deal with cultured cells, animals, and even epidemiological issues, so far a comprehensive analysis of respiratory outcomes as a function of the time elapsed after exposure to a low dose of ROFA is wanted. Thus, we aimed to investigate the...

Landfilling of waste incineration residues

DEFF Research Database (Denmark)

Christensen, Thomas Højlund; Astrup, Thomas; Cai, Zuansi

2002-01-01

Residues from waste incineration are bottom ashes and air-pollution-control (APC) residues including fly ashes. The leaching of heavy metals and salts from the ashes is substantial and a wide spectrum of leaching tests and corresponding criteria have been introduced to regulate the landfilling...

Trace elements in coal ash

Science.gov (United States)

Deonarine, Amrika; Kolker, Allan; Doughten, Michael W.

2015-01-01

Coal ash is a residual waste product primarily produced by coal combustion for electric power generation. Coal ash includes fly ash, bottom ash, and flue-gas desulfurization products (at powerplants equipped with flue-gas desulfurization systems). Fly ash, the most common form of coal ash, is used in a range of products, especially construction materials. A new Environmental Protection Agency ruling upholds designation of coal ash as a non-hazardous waste under Subtitle D of the Resource Conservation and Recovery Act, allowing for the continued beneficial use of coal ash and also designating procedures and requirements for its storage.

Mercury isotope fractionation during ore retorting in the Almadén mining district, Spain

Science.gov (United States)

Gray, John E.; Pribil, Michael J.; Higueras, Pablo L.

2013-01-01

Almadén, Spain, is the world's largest mercury (Hg) mining district, which has produced over 250,000 metric tons of Hg representing about 30% of the historical Hg produced worldwide. The objective of this study was to measure Hg isotopic compositions of cinnabar ore, mine waste calcine (retorted ore), elemental Hg (Hg0(L)), and elemental Hg gas (Hg0(g)), to evaluate potential Hg isotopic fractionation. Almadén cinnabar ore δ202Hg varied from − 0.92 to 0.15‰ (mean of − 0.56‰, σ = 0.35‰, n = 7), whereas calcine was isotopically heavier and δ202Hg ranged from − 0.03‰ to 1.01‰ (mean of 0.43‰, σ = 0.44‰, n = 8). The average δ202Hg enrichment of 0.99‰ between cinnabar ore and calcines generated during ore retorting indicated Hg isotopic mass dependent fractionation (MDF). Mass independent fractionation (MIF) was not observed in any of the samples in this study. Laboratory retorting experiments of cinnabar also were carried out to evaluate Hg isotopic fractionation of products generated during retorting such as calcine, Hg0(L), and Hg0(g). Calcine and Hg0(L) generated during these retorting experiments showed an enrichment in δ202Hg of as much as 1.90‰ and 0.67‰, respectively, compared to the original cinnabar ore. The δ202Hg for Hg0(g) generated during the retorting experiments was as much as 1.16‰ isotopically lighter compared to cinnabar, thus, when cinnabar ore was roasted, the resultant calcines formed were isotopically heavier, whereas the Hg0(g) generated was isotopically lighter in Hg isotopes.

Managing ash from the combustion of solid waste

International Nuclear Information System (INIS)

Hauser, R.

1992-01-01

This paper reports that with millions of tons of refuse being combusted each year, increasing concern over the environment impact of the residue produced has caused both regulators and the resource recovery industry to address the technical and regulatory issues relating to the safe handling and disposal of ash. The basic issue concerning solid waste combustion ash management in this country is how, based on past, recent, and ongoing scientific research, solid waste combustion ash should be handled. Typically, refuse contains approximately 20 to 25 percent residue, which is collected either on grates at the bottom of the combustion chamber or filtered from the exhaust gases by the air pollution control equipment. The fly ash component of the total residue stream is between 10 and 30 percent of the total residue while the bottom ash content ranges from 70 to 90 percent of the total weight, depending upon the air pollution control equipment utilized, especially acid gas scrubbing equipment

STUDY OF ASPHALT BINDER OIL RESIDUE AND MUNICIPAL SOLID WASTE ASH TO BE USED IN LOW TRAFFIC PAVEMENTS

Directory of Open Access Journals (Sweden)

Michéle Dal Toé Casagrande

2014-12-01

Full Text Available The great generation of urban solid has been a concern in several countries. This work presents a study with two materials: the asphalt binder oil residue accumulated in the bottom of asphalt tanks and the municipal solid waste ash, to be used, respectively, as a substitute of conventional binder in asphalt mixtures and for soil stabilization in pavements base layers. Were evaluated properties as the mechanical behavior of the mixtures through experimental tests. The results show the potential of incorporating these residues for low traffic roads, allowing the construction of low cost roads and an environmental use of the residue.

Nitrogen fixation by legumes in retorted shale

Energy Technology Data Exchange (ETDEWEB)

Hersman, L E; Molitoris, E; Klein, D A

1981-01-01

A study was made to determine whether retorted shale additions would significantly affect symbiotic N/sub 2/ fixation. Results indicate that small additions of the shale may stimulate plant growth but with higher concentrations plants are stressed, resulting in a decreased biomass and a compensatory effect of an increased number of nodules and N/sub 2/ fixation potential. (JMT)

Metals accumulations during thermal processing of sewage sludge - characterization of bottom ash and air pollution control (APC) residues

Science.gov (United States)

Kasina, Monika; Kowalski, Piotr R.; Michalik, Marek

2016-04-01

Due to increasing mass of sewage sludge, problems in its management have appeared. Over years sewage sludge was landfilled, however due to EU directives concerning environmental issues this option is no longer possible. This type of material is considered hazardous due to highly concentrated metals and harmful elements, toxic organic substances and biological components (e.g. parasites, microbes). Currently in Europe, incineration is considered to be the most reasonable method for sewage sludge treatment. As a result of sludge incineration significant amount of energy is recovered due to high calorific value of sewage sludge but bottom ash and APC residues are being produced. In this study we show the preliminary results of chemical and mineral analyses of both bottom ash and APC residues produced in fluidized bed boiler in sewage sludge incineration plant in Poland, with a special emphasis on metals which, as a part of incombustible fraction can accumulate in the residual materials after thermal processing. The bottom ash was a SiO2-P2O5-Fe2O3-CaO-Al2O3 dominated material. Main mineral phases identified in X-ray diffraction patterns were: quartz, feldspar, hematite, and phosphates (apatite and scholzite). The bottom ash was characterized by high content of Zn - 4472 mg kg-1, Cu - 665.5 mg kg-1, Pb - 138 mg kg-1, Ni - 119.5 mg kg-1, and interestingly high content of Au - 0.858 mg kg-1 The APC residues composition was dominated by soluble phases which represent more than 90% of the material. The XRD patterns indicated thenardite, halite, anhydrite, calcite and apatite as main mineral phases. The removal of soluble phases by dissolution in deionised water caused a significant mass reduction (ca. 3% of material remained on the filters). Calcite, apatite and quartz were main identified phases. The content of metals in insoluble material is relatively high: Zn - 6326 mg kg-1, Pb - 514.3 mg kg-1, Cu - 476.6 mg kg-1, Ni - 43.3 mg kg-1. The content of Cd, As, Se and Hg was

Recovery of iron oxide from coal fly ash

Science.gov (United States)

Dobbins, Michael S.; Murtha, Marlyn J.

1983-05-31

A high quality iron oxide concentrate, suitable as a feed for blast and electric reduction furnaces is recovered from pulverized coal fly ash. The magnetic portion of the fly ash is separated and treated with a hot strong alkali solution which dissolves most of the silica and alumina in the fly ash, leaving a solid residue and forming a precipitate which is an acid soluble salt of aluminosilicate hydrate. The residue and precipitate are then treated with a strong mineral acid to dissolve the precipitate leaving a solid residue containing at least 90 weight percent iron oxide.

Replacement of 5% of OPC by fly ash and APC residues from MSWI with electrodialytic pre-treatment

DEFF Research Database (Denmark)

Magro, Cátia; Kirkelund, Gunvor Marie; Guedes, Paula

2016-01-01

as pre-treatment prior to incorporation in mortar, aiming to stabilize and remove HM and chlorides. Eight ED experiments were performed for 7 days with a L/S ratio of 3.5. The number of compartments (2 or 3) and current density (0.1 or 1.0 mA cm-2) varied. After ED treatment the heavy metals left...... in the ash were not leached to the same extent as in the original ash. In mortar 5% of Ordinary Portland Cement was replaced by FA and APC residues (raw and ED upgraded). The studied parameters: compressive strength, HM leachability, and Cl content. The ED pre-treatment resulted in a decrease in both...

Scoping of oil shale retorting with nuclear fusion reactors

International Nuclear Information System (INIS)

Galloway, T.R.

1983-01-01

An engineering scoping study was conducted at the U.S. Department of Energy's request to see if a feasible concept could be developed for using nuclear fusion heat to improve in situ extraction by retorting of underground oil shale. It was found that a fusion heated, oxygen-free inert gas could be used for driving modified, in situ retorts at a higher yield, using lower grade shale and producing less environmental problems than present-day processes. It was also found to be economically attractive with return on investments of 20 to 30%. Fusion blanket technology required was found to be reasonable at hot gas delivery temperatures of about650 0 C (920 K). The scale of a fusion reactor at 2.8 GW(thermal) producing 45 000 Mg/day (335 000 barrel/day) was also found to be reasonable

Effect of fire residues (ash and char) on microbial activity, respiration and methanogenesis in three subtropical wetland soils

Science.gov (United States)

Medvedeff, C.; Hogue, B.; Inglett, P.

2011-12-01

Prescribed fire is a common restoration and maintenance technique in the southern United States. Prescribed burns coupled with frequent natural fires in South Florida can have devastating effects on ecosystem function. To determine the effect fire residues have on carbon biogeochemical cycling litter material was obtained from two restored and one native marl wetland in Everglades National Park and manipulated in a laboratory setting to produce ash and vegetation derived char. Based on vegetation biomass removal pre and post fire (insitu) appropriate aliquots of each fire residue was added to experimental microcosms as a soil amendment. Soil enzymes (β-glucosidase, cellobiohydrolase, phosphatase, bis-phosphate and leucine amino peptidase), aerobic and anaerobic respiration (CO2) potentials, extractable C and methanogenesis were measured over a 25 day period. Regardless of site C enzymes responded to both amendments within 5 days of addition. Similarly amended soil contained more extractable carbon in the reference and one of the restored sites. In the restored sites ash and char inhibited methanogenesis, had no effect on anaerobic CO2 potentials, but stimulated aerobic respiration after ten days. In contrast, within the first ten days phosphatase enzyme activity was lower in the ash treatment when compared to the control treatment and stimulation of aerobic respiration was observed in both treatment soils. After ten days ash stimulated methanogenic processing while suppressing anaerobic CO2 production suggesting methanogens in this ecosystem may be dependant on usable carbon substrates derived from aerobic microbial processing. This study illustrates the variable response of C parameters to complete and incomplete combusted materials produced from both prescribed and natural fires with particular importance to fire adapted ecosystems.

Double Retort System for Materials Compatibility Testing

International Nuclear Information System (INIS)

V. Munne; EV Carelli

2006-01-01

With Naval Reactors (NR) approval of the Naval Reactors Prime Contractor Team (NRPCT) recommendation to develop a gas cooled reactor directly coupled to a Brayton power conversion system as the Space Nuclear Power Plant (SNPP) for Project Prometheus (References a and b) there was a need to investigate compatibility between the various materials to be used throughout the SNPP. Of particular interest was the transport of interstitial impurities from the nickel-base superalloys, which were leading candidates for most of the piping and turbine components to the refractory metal alloys planned for use in the reactor core. This kind of contamination has the potential to affect the lifetime of the core materials. This letter provides technical information regarding the assembly and operation of a double retort materials compatibility testing system and initial experimental results. The use of a double retort system to test materials compatibility through the transfer of impurities from a source to a sink material is described here. The system has independent temperature control for both materials and is far less complex than closed loops. The system is described in detail and the results of three experiments are presented

Retort for coking peat, brown coal, bituminous shale, etc

Energy Technology Data Exchange (ETDEWEB)

1902-05-14

The retort leads the gases and vapors into the coking chamber, between the inside heater and the outer heating shaft-wall. Over-lapping, double-faced acting rings are arranged, over which the charge in two or more separate vertical layers is transported.

Electrodialytic removal of heavy metals and chloride from municipal solid waste incineration fly ash and air pollution control residue in suspension - test of a new two compartment experimental cell

DEFF Research Database (Denmark)

Kirkelund, Gunvor Marie; Magro, Cátia; Guedes, Paula

2015-01-01

Municipal solid waste incineration (MSWI) residues such as fly ash and air pollution control (APC) residues are classified as hazardous waste and disposed of, although they contain potential resources. The most problematic elements in MSWI residues are leachable heavy metals and salts. For reuse...... of MSWI residues in for instance concrete, the aim of remediation should be reduction of the heavy metal leaching, while at the same time keeping the alkaline pH, so the residue can replace cement. In this study a MSWI residues were subjected to electrodialytic remediation under various experimental...... heavy metal leaching except when the pH was reduced to a level below 8 for the fly ash. On the other hand, Cr leaching increased by the electrodialytic treatment. Cl leaching from the MSWI residues was less dependent on experimental conditions and was reduced in all experiments compared to the initial...

Stability of 2-Alkylcyclobutanones in irradiated retort pouch Gyudon topping during room temperature storage

International Nuclear Information System (INIS)

Kitagawa, Yoko; Okihashi, Masahiro; Takatori, Satoshi; Fukui, Naoki; Kajimura, Keiji; Obana, Hirotaka; Furuta, Masakazu

2016-01-01

2-Alkylcyclobutanones (ACBs), such as 2-dodecylcyclobutanone (DCB) and 2-tetradecylcylobutanone (TCB) are specific products in the irradiated liquid. Thus, DCB and TCB are suitable for indicators of the irradiation history of food. We previously reported DCB and TCB concentrations in irradiated retort pouch Gyudon topping (instant Gyudon mixes which were made from a beef, onion and soy sauce and could be preserved for a long term at room temperature) after storage for one year. Here, we have evaluated the stability of ACBs preserved in irradiated retort pouch Gyudon topping at room temperature for three years. Although interfering peaks were detected frequently after the storage at room temperature, it was possible for the detection of the irradiation history and there was no apparent decrease of ACBs concentrations in comparison with the one year storage after irradiation. These results concluded that DCB and TCB formed in retort pouch would be stable at room temperature for three years. (author)

Method for explosive expansion toward horizontal free faces for forming an in situ oil shale retort

Science.gov (United States)

Ricketts, Thomas E.

1980-01-01

Formation is excavated from within a retort site in formation containing oil shale for forming a plurality of vertically spaced apart voids extending horizontally across different levels of the retort site, leaving a separate zone of unfragmented formation between each pair of adjacent voids. Explosive is placed in each zone, and such explosive is detonated in a single round for forming an in situ retort containing a fragmented permeable mass of formation particles containing oil shale. The same amount of formation is explosively expanded upwardly and downwardly toward each void. A horizontal void excavated at a production level has a smaller horizontal cross-sectional area than a void excavated at a lower level of the retort site immediately above the production level void. Explosive in a first group of vertical blast holes is detonated for explosively expanding formation downwardly toward the lower void, and explosive in a second group of vertical blast holes is detonated in the same round for explosively expanding formation upwardly toward the lower void and downwardly toward the production level void for forming a generally T-shaped bottom of the fragmented mass.

Lunar ash flows - Isothermal approximation.

Science.gov (United States)

Pai, S. I.; Hsieh, T.; O'Keefe, J. A.

1972-01-01

Suggestion of the ash flow mechanism as one of the major processes required to account for some features of lunar soil. First the observational background and the gardening hypothesis are reviewed, and the shortcomings of the gardening hypothesis are shown. Then a general description of the lunar ash flow is given, and a simple mathematical model of the isothermal lunar ash flow is worked out with numerical examples to show the differences between the lunar and the terrestrial ash flow. The important parameters of the ash flow process are isolated and analyzed. It appears that the lunar surface layer in the maria is not a residual mantle rock (regolith) but a series of ash flows due, at least in part, to great meteorite impacts. The possibility of a volcanic contribution is not excluded. Some further analytic research on lunar ash flows is recommended.

Experimental Assessment of the Mass of Ash Residue During the Burning of Droplets of a Composite Liquid Fuel

Science.gov (United States)

Glushkov, D. O.; Zakharevich, A. V.; Strizhak, P. A.; Syrodoi, S. V.

2018-05-01

An experimental study has been made of the regularities of burning of single droplets of typical compositions of a composite liquid fuel during the heating by an air flow with a varied temperature (600-900 K). As the basic components of the compositions of the composite liquid fuel, use was made of the: waste of processing (filter cakes) of bituminous coals of ranks K, C, and T, waste motor, turbine, and transformer oils, process mixture of mazut and oil, heavy crude, and plasticizer. The weight fraction of a liquid combustible component (petroleum) product) ranged within 0-15%. Consideration has been given to droplets of a composite liquid fuel with dimensions (radius) of 0.5 to 2 mm. Conditions of low-temperature initiation of combustion to ensure a minimum possible mass of solid incombustible residue have been determined. Petroleum products have been singled out whose addition to the composition of the composite liquid fuel tends to increase the ash mass (compared to the corresponding composition without a liquid combustible component). Approximation dependences have been obtained which permit predicting the influence of the concentration of the liquid petroleum product as part of the composite liquid fuel on the ash-residue mass.

Improved mechanical properties of retorted carrots by ultrasonic pre-treatments.

Science.gov (United States)

Day, Li; Xu, Mi; Øiseth, Sofia K; Mawson, Raymond

2012-05-01

The use of ultrasound pre-processing treatment, compared to blanching, to enhance mechanical properties of non-starchy cell wall materials was investigated using carrot as an example. The mechanical properties of carrot tissues were measured by compression and tensile testing after the pre-processing treatment prior to and after retorting. Carrot samples ultrasound treated for 10 min at 60 °C provided a higher mechanical strength (P<0.05) to the cell wall structure than blanching for the same time period. With the addition of 0.5% CaCl(2) in the pre-treatment solution, both blanching and ultrasound treatment showed synergistic effect on enhancing the mechanical properties of retorted carrot pieces. At a relatively short treatment time (10 min at 60 °C) with the use of 0.5% CaCl(2), ultrasound treatment achieved similar enhancement to the mechanical strength of retorted carrots to blanching for a much longer time period (i.e. 40 min). The mechanism involved appears to be related to the stress responses present in all living plant matter. However, there is a need to clarify the relative importance of the potential stress mechanisms in order to get a better understanding of the processing conditions likely to be most effective. The amount of ultrasound treatment required is likely to involve low treatment intensities and there are indications from the structural characterisation and mechanical property analyses that the plant cell wall tissues were more elastic than that accomplished using low temperature long time blanching. Crown Copyright © 2011. Published by Elsevier B.V. All rights reserved.

System for manufacturing ash products and energy from refuse waste

Energy Technology Data Exchange (ETDEWEB)

Sutin, G.L.; Mahoney, P.F.

1996-01-04

The present invention provides a system of manufacturing energy and ash products from solid waste. The system includes apparatus for receiving solid waste for processing, apparatus for shredding the received solid waste, apparatus for removing ferrous material from the shredded solid waste to create processed refuse fuel (PRF) and apparatus for efficiently combusting the PRF. A conveyor transfers the PRF to the combusting apparatus such that the density of the PRF is always controlled for continuous non-problematic flow. Apparatus for recovering residual combustion particulate from the combustion residual gases and for recovering solid ash residue provides the system with the ability to generate steam and electrical energy, and to recover for reuse and recycling valuable materials from the solid ash residue. (author) figs.

Study of a large rapid ashing apparatus and a rapid dry ashing method for biological samples and its application

International Nuclear Information System (INIS)

Jin Meisun; Wang Benli; Liu Wencang

1988-04-01

A large rapid-dry-ashing apparatus and a rapid ashing method for biological samples are described. The apparatus consists of specially made ashing furnace, gas supply system and temperature-programming control cabinet. The following adventages have been showed by ashing experiment with the above apparatus: (1) high speed of ashing and saving of electric energy; (2) The apparatus can ash a large amount of samples at a time; (3) The ashed sample is pure white (or spotless), loose and easily soluble with few content of residual char; (4) The fresh sample can also be ashed directly. The apparatus is suitable for ashing a large amount of the environmental samples containing low level radioactivity trace elements and the medical, food and agricultural research samples

Arrangement of furnaces and retorts for the distillation of shale, etc. [injection of hot air

Energy Technology Data Exchange (ETDEWEB)

Lahore, M

1846-01-31

The patent is concerned with the distillation of dried materials, the distillation being facilitated by injection of hot air into the retorts. Figures show apparatus for heating the air, consisting of a series of pipes, connected together and placed horizontally in the interior of the furnace on bricks arranged in such a way that the flames and smoke circulate, as shown, around each pipe, touching first all the surface of the large one placed in the center. The air enters this tube, and from it passes into the others which it runs through successively, coming finally into the last pipe, being heated in this journey to a very high temperature. The last tube ends in a bell from which different branches start, each supplied with stop-cocks, to lead this hot air into the different sections of the retort. With the stop-cocks the quantity of air can be regulated at will, in the compartment of the retort, for accelerating the operation more or less.

The effect of low-NOx combustion on residual carbon in fly ash and its adsorption capacity for air entrainment admixtures in concrete

DEFF Research Database (Denmark)

Pedersen, Kim Hougaard; Jensen, Anker Degn; Dam-Johansen, Kim

2010-01-01

been combusted in an entrained flow reactor to test the impact of changes in operating conditions and fuel type on the AEA adsorption of ash and NOx formation. Increased oxidizing conditions, obtained by improved fuel-air mixing or higher excess air, decreased the AEA requirements of the produced ash......Fly ash from pulverized coal combustion contains residual carbon that can adsorb the air-entraining admixtures (AEAs) added to control the air entrainment in concrete. This is a problem that has increased by the implementation of low-NOx combustion technologies. In this work, pulverized fuel has...... by up to a factor of 25. This was due to a lower carbon content in the ash and a lower specific AEA adsorptivity of the carbon. The latter was suggested to be caused by changes in the adsorption properties of the unburned char and a decreased formation of soot, which was found to have a large AEA...

Long-term leaching of nutrients and contaminants from wood combustion ashes

DEFF Research Database (Denmark)

Maresca, Alberto; Hyks, J.; Astrup, Thomas Fruergaard

2018-01-01

With increasing amounts of woody biomass being combusted for energy purposes worldwide, more wood ash is being generated and needs management. As an alternative to landfilling, residues may be utilised for liming and fertilising purposes on forest soils. Comprehensive evaluations of long-term lea......With increasing amounts of woody biomass being combusted for energy purposes worldwide, more wood ash is being generated and needs management. As an alternative to landfilling, residues may be utilised for liming and fertilising purposes on forest soils. Comprehensive evaluations of long......-term leaching from these residues are needed in order to assess potential environmental impacts associated with their utilisation. Two Danish wood ash samples, one fly ash and one mixed ash (a combination of fly ash and bottom ash), were evaluated in long-term percolation column tests (up to L/S ∼2000 L....../kg), in order to quantify the release of major, minor and trace metal(loid)s. While columns of three different lengths were used, the leaching of individual elements could be described as a function of the L/S ratio – irrespective of the column length. At L/S 1000 L/kg, the cumulative releases of K, S, Na, Ca...

The variability in iron speciation in size fractionated residual oil fly ash particulate matter (ROFA PM).

Science.gov (United States)

Pattanaik, Sidhartha; Huggins, Frank E; Huffman, Gerald P

2016-08-15

Ambient particulate matter (PM) containing iron can catalyze Fenton reaction leading to the production of reactive oxygen species in cells. It can also catalyze atmospheric redox reaction. These reactions are governed by the physicochemical characteristics of iron in ambient PM. As a surrogate for ambient PM, we prepared residual oil fly ash PM (ROFA PM) in a practical fire tube boiler firing residual oils with varying sulfur and ash contents. The ROFA particles were resolved into fine PM or PM2.5 (aerodynamic diameter (AD)iron speciation in PM2.5+ was ascertained using X-ray absorption spectroscopy and leaching method while that in PM2.5 was reported earlier. The results of both studies are compared to get an insight into the variability in the iron speciation in different size fractions. The results show the predominance of ferric sulfate, with a minor spinal ferrite in both PM (i.e. ZnxNi1-xFe2O4 in PM2.5, ZnFe2O4 in PM2.5+). The iron solubility in ROFA PM depends on its speciation, mode of incorporation of iron into particle's carbonaceous matrix, the grade and composition of oils, and pH of the medium. The soluble fraction of iron in PM is critical in assessing its interaction with the biological systems and its toxic potential. Copyright © 2016 Elsevier B.V. All rights reserved.

Effects of chemical composition of fly ash on efficiency of metal separation in ash-melting of municipal solid waste

Energy Technology Data Exchange (ETDEWEB)

Okada, Takashi, E-mail: t-okada@u-fukui.ac.jp [Laboratory of Solid Waste Disposal Engineering, Graduate School of Engineering, Hokkaido University, Kita 13 Nishi 8, Kita-ku, Sapporo 060-8628 (Japan); Tomikawa, Hiroki [Laboratory of Solid Waste Disposal Engineering, Graduate School of Engineering, Hokkaido University, Kita 13 Nishi 8, Kita-ku, Sapporo 060-8628 (Japan)

2013-03-15

Highlights: ► Separation of Pb and Zn from Fe and Cu in ash-melting of municipal solid waste. ► Molar ratio of Cl to Na and K in fly ash affected the metal-separation efficiency. ► The low molar ratio and a non-oxidative atmosphere were better for the separation. - Abstract: In the process of metal separation by ash-melting, Fe and Cu in the incineration residue remain in the melting furnace as molten metal, whereas Pb and Zn in the residue are volatilized. This study investigated the effects of the chemical composition of incineration fly ash on the metal-separation efficiency of the ash-melting process. Incineration fly ash with different chemical compositions was melted with bottom ash in a lab-scale reactor, and the efficiency with which Pb and Zn were volatilized preventing the volatilization of Fe and Cu was evaluated. In addition, the behavior of these metals was simulated by thermodynamic equilibrium calculations. Depending on the exhaust gas treatment system used in the incinerator, the relationships among Na, K, and Cl concentrations in the incineration fly ash differed, which affected the efficiency of the metal separation. The amounts of Fe and Cu volatilized decreased by the decrease in the molar ratio of Cl to Na and K in the ash, promoting metal separation. The thermodynamic simulation predicted that the chlorination volatilization of Fe and Cu was prevented by the decrease in the molar ratio, as mentioned before. By melting incineration fly ash with the low molar ratio in a non-oxidative atmosphere, most of the Pb and Zn in the ash were volatilized leaving behind Fe and Cu.

Anaerobic biological treatment of in-situ retort water

Energy Technology Data Exchange (ETDEWEB)

Ossio, E.; Fox, P.

1980-03-01

Anaerobic fermentation was successfully used in a laboratory-scale batch digester to remove soluble organics from retort water. Required pretreatment includes reduction of ammonia levels to 360 mg-N/l, pH adjustment to 7.0, sulfide control, and the addition of the nutrients, calcium, magnesium, and phoshorus. If the prescribed pretreatment is used, BOD/sub 5/ and COD removal efficiencies of 89 to 90% and 65 to 70% are achieved, respectively.

Retortable Laminate/Polymeric Food Tubes for Specialized Feeding

Science.gov (United States)

2012-06-01

Report STP #3010 Results and Accomplishments (June 2010 – June 2012) Report No: FTR 303 CDRL Sequence: A003 June 2012 CORANET CONTRACT #: SP4701-08-D...June 2010 - June 2012 Retortable Laminate/Polymeric Food Tubes for Specialized Feeding - STP # 3010 SP4701-08-D-0004 MANTECH (0708011S) CORANET A003...on commercial off-the-shelf materials and not military unique. A market survey of commercially available laminated tubes revealed that they are all

Stability of 2-Alkylcyclobutanones in irradiated retort pouch Gyudon topping during room temperature storage

International Nuclear Information System (INIS)

Kitagawa, Yoko; Okihashi, Masahiro; Takatori, Satoshi; Fukui, Naoki; Kajimura, Keiji; Obana, Hirotaka; Furuta, Masakazu

2014-01-01

2-Alkylcyclobutanones (ACBs), such as 2-dodecylcyclobutanone (DCB) and 2-tetradecylcylobutanone (TCB) are specific products from irradiated lipid. Thus, DCB and TCB are suitable for indicators of the irradiation history of food. The purpose of this study was to clarify the stability of ACBs in food, kept at room temperature for a long period. We evaluated DCB and TCB in irradiated retort pouch Gyudon topping (instant Gyudon mixes which were made from a beef, onion and soy sauce), which could be preserved for a long term at room temperature, after storage for one year. DCB and TCB were detected at doses of 0.6-4.5 kGy in irradiated retort pouch Gyudon topping. The peaks of DCB and TCB were separated from other peaks on the chromatogram with GC-MS. The concentration of DCB and TCB were periodically determined till 12 months later of irradiation. The dose-response curves of DCB and TCB were almost identical with those obtained from the samples after the 12 months storage at room temperature. These results concluded that DCB and TCB formed in retort pouch would stable at room temperature at least 12 months. (author)

77 FR 25206 - Proposed Extension of Existing Information Collection; Underground Retorts

Science.gov (United States)

2012-04-27

... information in accordance with the Paperwork Reduction Act of 1995. This program helps to ensure that requested data can be provided in the desired format, reporting burden (time and financial resources) is... Information Collection; Underground Retorts AGENCY: Mine Safety and Health Administration, Labor. ACTION...

Reuse potential of low-calcium bottom ash as aggregate through pelletization.

Science.gov (United States)

Geetha, S; Ramamurthy, K

2010-01-01

Coal combustion residues which include fly ash, bottom ash and boiler slag is one of the major pollutants as these residues require large land area for their disposal. Among these residues, utilization of bottom ash in the construction industry is very low. This paper explains the use of bottom ash through pelletization. Raw bottom ash could not be pelletized as such due to its coarseness. Though pulverized bottom ash could be pelletized, the pelletization efficiency was low, and the aggregates were too weak to withstand the handling stresses. To improve the pelletization efficiency, different clay and cementitious binders were used with bottom ash. The influence of different factors and their interaction effects were studied on the duration of pelletization process and the pelletization efficiency through fractional factorial design. Addition of binders facilitated conversion of low-calcium bottom ash into aggregates. To achieve maximum pelletization efficiency, the binder content and moisture requirements vary with type of binder. Addition of Ca(OH)(2) improved the (i) pelletization efficiency, (ii) reduced the duration of pelletization process from an average of 14-7 min, and (iii) reduced the binder dosage for a given pelletization efficiency. For aggregate with clay binders and cementitious binder, Ca(OH)(2) and binder dosage have significant effect in reducing the duration of pelletization process. 2010 Elsevier Ltd. All rights reserved.

Characteristics of ash and particle emissions during bubbling fluidised bed combustion of three types of residual forest biomass.

Science.gov (United States)

Ribeiro, João Peres; Vicente, Estela Domingos; Alves, Célia; Querol, Xavier; Amato, Fulvio; Tarelho, Luís A C

2017-04-01

Combustion of residual forest biomass (RFB) derived from eucalypt (Eucalyptus globulus), pine (Pinus pinaster) and golden wattle (Acacia longifolia) was evaluated in a pilot-scale bubbling fluidised bed reactor (BFBR). During the combustion experiments, monitoring of temperature, pressure and exhaust gas composition has been made. Ash samples were collected at several locations along the furnace and flue gas treatment devices (cyclone and bag filter) after each combustion experiment and were analysed for their unburnt carbon content and chemical composition. Total suspended particles (TSP) in the combustion flue gas were evaluated at the inlet and outlet of cyclone and baghouse filter and further analysed for organic and elemental carbon, carbonates and 57 chemical elements. High particulate matter collection efficiencies in the range of 94-99% were observed for the baghouse, while removal rates of only 1.4-17% were registered for the cyclone. Due to the sand bed, Si was the major element in bottom ashes. Fly ashes, in particular those from eucalypt combustion, were especially rich in CaO, followed by relevant amounts of SiO 2 , MgO and K 2 O. Ash characteristics varied among experiments, showing that their inorganic composition strongly depends on both the biomass composition and combustion conditions. Inorganic constituents accounted for TSP mass fractions up to 40 wt%. Elemental carbon, organic matter and carbonates contributed to TSP mass fractions in the ranges 0.58-44%, 0.79-78% and 0.01-1.7%, respectively.

Investigation of the Geokinetics horizontal in situ oil-shale-retorting process. Fourth annual report, 1980

Energy Technology Data Exchange (ETDEWEB)

Hutchinson, D.L. (ed.)

1981-03-01

The Geokinetics in situ shale oil project is a cooperative venture between Geokinetics Inc. and the US Department of Energy. The objective is to develop a true in situ process for recovering shale oil using a fire front moving in a horizontal direction. The project is being conducted at a field site, Kamp Kerogen, located 70 miles south of Vernal, Utah. This Fourth Annual Report covers work completed during the calendar year 1980. During 1980 one full-size retort was blasted. Two retorts, blasted the previous year, were burned. A total of 4891 barrels of oil was produced during the year.

Effect of fire exposure on cracking, spalling and residual strength of fly ash geopolymer concrete

International Nuclear Information System (INIS)

Sarker, Prabir Kumar; Kelly, Sean; Yao, Zhitong

2014-01-01

Highlights: • Fire endurance of fly ash geopolymer concrete has been studied. • No spalling in geopolymer concrete cylinders up to 1000 °C fire. • Less cracking and better fire endurance of geopolymer concrete than OPC concrete. • Geopolymer microstructure remained stable up to 1000 °C fire. - Abstract: Fly ash based geopolymer is an emerging alternative binder to cement for making concrete. The cracking, spalling and residual strength behaviours of geopolymer concrete were studied in order to understand its fire endurance, which is essential for its use as a building material. Fly ash based geopolymer and ordinary portland cement (OPC) concrete cylinder specimens were exposed to fires at different temperatures up to 1000 °C, with a heating rate of that given in the International Standards Organization (ISO) 834 standard. Compressive strength of the concretes varied in the range of 39–58 MPa. After the fire exposures, the geopolymer concrete specimens were found to suffer less damage in terms of cracking than the OPC concrete specimens. The OPC concrete cylinders suffered severe spalling for 800 and 1000 °C exposures, while there was no spalling in the geopolymer concrete specimens. The geopolymer concrete specimens generally retained higher strength than the OPC concrete specimens. The Scanning Electron Microscope (SEM) images of geopolymer concrete showed continued densification of the microstructure with the increase of fire temperature. The strength loss in the geopolymer concrete specimens was mainly because of the difference between the thermal expansions of geopolymer matrix and the aggregates

Plutonium dissolution from Rocky Flats Plant incinerator ash

International Nuclear Information System (INIS)

Delegard, C.H.

1985-06-01

Rockwell Hanford Operations (Rockwell) soon will commence recovery of plutonium from Rocky Flats Plant incinerator ash. In preparation for this processing, Rockwell undertook literature and laboratory studies to identify, select and optimize plutonium dissolution methods for treating the ash. Ash reburning, followed by dissolution in nitric acid containing calcium fluoride, was selected as the processing method for the ash. Recommended values of process parameters were identified. Using the selected process, 99.5% plutonium recovery was achieved, leaving about 12.7 wt % heel residue for an equal weight composite of the three ashes tested. 15 refs., 26 figs

Coal combustion ashes: A radioactive Waste?

International Nuclear Information System (INIS)

Michetti, F.P.; Tocci, M.

1992-01-01

The radioactive substances naturally hold in fossil fuels, such as Uranium and Thorium, after the combustion, are subjected to an increase of concentration in the residual combustion products as flying ashes or as firebox ashes. A significant percentage of the waste should be classified as radioactive waste, while the political strategies seems to be setted to declassify it as non-radioactive waste. (Author)

Thermal treatment of solid residues from WtE units: A review

International Nuclear Information System (INIS)

Lindberg, Daniel; Molin, Camilla; Hupa, Mikko

2015-01-01

Highlights: • We review the thermal treatment methods for ashes and residues from WtE plants. • We review the results from extensive laboratory work on vitrification, melting and vaporization of ash. • We analyze the results from the extensive patent literature on thermal treatment. • We review industrial concepts for thermal treatment of ash. - Abstract: Thermal treatment methods of bottom ash, fly ash and various types of APC (air pollution control) residues from waste-to-energy plants can be used to obtain environmentally stable material. The thermal treatment processes are meant to reduce the leachability of harmful residue constituents, destroy toxic organic compounds, reduce residue volume, and produce material suitable for utilization. Fly ash and APC residues often have high levels of soluble salts, particularly chlorides, metals such as cadmium, lead, copper and zinc, and trace levels of organic pollutants such as dioxins and furans. Different thermal treatment methods can be used to either decompose or stabilize harmful elements and compounds in the ash, or separate them from the ash to get a material that can be safely stored or used as products or raw materials. In the present paper, thermal treatment methods, such as sintering, vitrification, and melting have been reviewed. In addition to a review of the scientific literature, a survey has been made of the extensive patent literature in the field

Thermal treatment of solid residues from WtE units: A review

Energy Technology Data Exchange (ETDEWEB)

Lindberg, Daniel, E-mail: daniel.lindberg@abo.fi; Molin, Camilla, E-mail: camilla.molin@abo.fi; Hupa, Mikko, E-mail: mikko.hupa@abo.fi

2015-03-15

Highlights: • We review the thermal treatment methods for ashes and residues from WtE plants. • We review the results from extensive laboratory work on vitrification, melting and vaporization of ash. • We analyze the results from the extensive patent literature on thermal treatment. • We review industrial concepts for thermal treatment of ash. - Abstract: Thermal treatment methods of bottom ash, fly ash and various types of APC (air pollution control) residues from waste-to-energy plants can be used to obtain environmentally stable material. The thermal treatment processes are meant to reduce the leachability of harmful residue constituents, destroy toxic organic compounds, reduce residue volume, and produce material suitable for utilization. Fly ash and APC residues often have high levels of soluble salts, particularly chlorides, metals such as cadmium, lead, copper and zinc, and trace levels of organic pollutants such as dioxins and furans. Different thermal treatment methods can be used to either decompose or stabilize harmful elements and compounds in the ash, or separate them from the ash to get a material that can be safely stored or used as products or raw materials. In the present paper, thermal treatment methods, such as sintering, vitrification, and melting have been reviewed. In addition to a review of the scientific literature, a survey has been made of the extensive patent literature in the field.

Metallic elements fractionation in municipal solid waste incineration residues

Science.gov (United States)

Kowalski, Piotr R.; Kasina, Monika; Michalik, Marek

2016-04-01

Municipal solid waste incineration (MSWI) residues are represented by three main materials: bottom ash, fly ash and air pollution control (APC) residues. Among them ˜80 wt% is bottom ash. All of that materials are products of high temperature (>1000° C) treatment of waste. Incineration process allows to obtain significant reduction of waste mass (up to 70%) and volume (up to 90%) what is commonly used in waste management to reduce the amount need to be landfilled or managed in other way. Incineration promote accumulation non-combustible fraction of waste, which part are metallic elements. That type of concentration is object of concerns about the incineration residues impact on the environment and also gives the possibility of attempts to recover them. Metallic elements are not equally distributed among the materials. Several factors influence the process: melting points, volatility and place and forms of metallic occurrence in the incinerated waste. To investigate metallic elements distribution in MSWI residues samples from one of the biggest MSW incineration plant in Poland were collected in 2015. Chemical analysis with emphasis on the metallic elements content were performed using inductively coupled plasma optical emission (ICP-OES) and mass spectrometry (ICP-MS). The bottom ash was a SiO2-CaO-Al2O3-Fe2O3-Na2O rich material, whereas fly ash and APC residues were mostly composed of CaO and SiO2. All of the materials were rich in amorphous phase occurring together with various, mostly silicate crystalline phases. In a mass of bottom ash 11 wt% were metallic elements but also in ashes 8.5 wt% (fly ash) and ˜4.5 wt% (APC residues) of them were present. Among the metallic elements equal distribution between bottom and fly ash was observed for Al (˜3.85 wt%), Mn (770 ppm) and Ni (˜65 ppm). In bottom ash Fe (5.5 wt%), Cr (590 ppm) and Cu (1250 ppm) were concentrated. These values in comparison to fly ash were 5-fold higher for Fe, 3-fold for Cu and 1.5-fold for

Charcoal as an alternative energy carrier. Pt. 2: Conversion of biomass

Energy Technology Data Exchange (ETDEWEB)

Holstad, A

1978-12-01

Terrestrial biomass, residues from forestry, agriculture and farming can be converted by biochemical or thermochemical techniques to fuels. The charcoal yield depends on the raw materials, moisture contents, the temperature of carbonisation and the processing equipment. The yield is reduced by 2 - 3% when using softwood and furthermore with higher temperature of carbonisation. Generally charcoal contains 80 - 90% carbon, 0,5 - 10% ash and 7 - 30% volatile matter. Theoretically the following products are obtained when pyrolising wood: 34,7% Charcoal, 24,9% H/sub 2/O, 10,9% CO/sub 2/, 4,15 CO, 1,6% Methanol, 5,9% Acetic Acid and 17,9% Tar. Units for production of charcoal are large and small kilns, transportable Thomas retorts and Cornell retorts with a production of 1,3 - 6 tons charcoal/day, and the large Lambiotte retort, multiple-hearth furnaces and fluidized-bed reactors. Interesting is also the new equipment of Skogens Kol in Sweden. These large units have a production capacity of 16 - 80 tons charcoal/day. Important production parameters include charcoal yield, labour requirements, air pollution and cost. Based on these parameters the Cornell retort is considered the best unit for production of small quantities of charcoal and Skogens Kol seems to be the most interesting large unit. 17 drawings, 14 tables.

Identification and quantification of radionuclides in coal ash. Final report

International Nuclear Information System (INIS)

Alleman, J.E.; Clikeman, F.M.; Skronski, T.

1998-01-01

One of the important environmental issues raised recently in regard to coal ash reuse for highway construction purposes (e.g., embankment development) is that of worker, and public, exposure to radiation which might possibly be emitted by these types of residues. This research project subsequently addressed the associated issue of radiation emission by coal ash residuals generated within the State of Indiana, covering both fly ash and bottom ash materials. Samples were obtained at sixteen different coal-fired power generating facilities within Indiana and subjected to quantitative analysis of their associated gamma-ray emission levels. After identifying the responsible radionuclides, a conservative approximation was then developed for the worst-case potential occupational exposure with construction employees working on this type of high-volume, coal ash embankment. In turn, these potential emissions levels were compared to those of other traditional construction materials and other common sources

Fungal leaching of valuable metals from a power plant residual ash using Penicillium simplicissimum: Evaluation of thermal pretreatment and different bioleaching methods.

Science.gov (United States)

Rasoulnia, P; Mousavi, S M; Rastegar, S O; Azargoshasb, H

2016-06-01

Each year a tremendous volume of V-Ni rich ashes is produced by fuel oil consuming power plants throughout the world. Recovery of precious metals existing in these ashes is very important from both economic and environmental aspects. The present research was aimed at investigating bioleaching potential of Penicillium simplicissimum for the recovery of metals from power plant residual ash (PPR ash) using different bioleaching methods such as one-step, two-step, and spent-medium bioleaching at 1% (w/v) pulp density. Furthermore, the effects of thermal pretreatment on leaching of V, Ni, and Fe, as major elements present in PPR ash, were studied. Thermal pretreatment at various temperatures removed the carbonaceous and volatile fraction of the ash and affected the fungal growth and metal leachability. The highest extraction yields of V and Ni were achieved for the original PPR ash, using spent-medium bioleaching in which nearly 100% of V and 40% of Ni were extracted. The maximum extraction yield of Fe (48.3%) was obtained for the pretreated PPR ash at 400°C by spent-medium bioleaching. In addition, the fungal growth in pure culture was investigated through measurement of produced organic acids via high performance liquid chromatography (HPLC). Chemical leaching experiments were performed, using commercial organic acids at the same concentrations as those produced under optimum condition of fungal growth (5237ppm citric, 3666ppm gluconic, 1287ppm oxalic and 188ppm malic acid). It was found that in comparison to chemical leaching, bioleaching improved V and Ni recovery up to 19% and 12%, respectively. Moreover, changes in physical and chemical properties as well as morphology of the samples utilizing appropriate analytical methods such as XRF, XRD, FTIR, and FE-SEM were comprehensively investigated. Copyright © 2016 Elsevier Ltd. All rights reserved.

Increase in efficiency and reduction of generation cost at hard coal-fired power plants. Post-combustion of combustion residues from co-firing of RDF and biomass during dry ash removal

Energy Technology Data Exchange (ETDEWEB)

Baur, Guenter [Magaldi Power GmbH, Esslingen (Germany); Spindeldreher, Olaf [RWE Generation SE, Werne (Germany); RWE Generation SE, Essen (Germany)

2013-09-01

Secondary as well as substitute fuels are being used in hard coal-fired power plants to improve efficiency and to enlarge fuel flexibility. However, grinding and firing systems of the existing coal-fired plants are not designed for those co-fuels. Any deterioration of the combustion performance would reduce the power output and increase ash disposal costs by increased content of combustion residues. The application of air-cooled ash removal, with simultaneous and controlled post-combustion of unburned residues on the conveyor belt, enlarges the furnace and maintains combustion efficiency even with different fuel qualities. Plant efficiency can also be increased through heat recovery. (orig.)

Aluminium recovery from waste incineration bottom ash, and its oxidation level.

Science.gov (United States)

Biganzoli, Laura; Grosso, Mario

2013-09-01

The recovery of aluminium (Al) scraps from waste incineration bottom ash is becoming a common practice in waste management. However, during the incineration process, Al in the waste undergoes oxidation processes that reduce its recycling potential. This article investigates the behaviour of Al scraps in the furnace of two selected grate-fired waste-to-energy plants and the amount recoverable from the bottom ash. About 21-23% of the Al fed to the furnace with the residual waste was recovered and potentially recycled from the bottom ash. Out of this amount, 76-87% was found in the bottom ash fraction above 5 mm and thus can be recovered with standard eddy current separation technology. These values depend on the characteristics and the mechanical strength of the Al items in the residual waste. Considering Al packaging materials, about 81% of the Al in cans can be recovered from the bottom ash as an ingot, but this amount decreases to 51% for trays, 27% for a mix of aluminium and poly-laminated foils and 47% for paper-laminated foils. This shows that the recovery of Al from the incineration residues increases proportionally to the thickness of the packaging.

Chemical and physical properties of cyclone fly ash from the grate-fired boiler incinerating forest residues at a small municipal district heating plant (6MW).

Science.gov (United States)

Pöykiö, R; Rönkkömäki, H; Nurmesniemi, H; Perämäki, P; Popov, K; Välimäki, I; Tuomi, T

2009-03-15

In Finland, the new limit values for maximal allowable heavy metal concentrations for materials used as an earth construction agent came into force in July 2006. These limit values are applied if ash is utilized, e.g. in roads, cycling paths, pavements, car parks, sport fields, etc. In this study we have determined the most important chemical and physical properties of the cyclone fly ash originating from the grate-fired boiler incinerating forest residues (i.e. wood chips, sawdust and bark) at a small municipal district heating plant (6 MW), Northern Finland. This study clearly shows that elements are enriched in cyclone fly ash, since the total element concentrations in the cyclone fly ash were within 0.2-10 times higher than those in the bottom ash. The total concentrations of Cd (25 mg kg(-1); d.w.), Zn (3630 mg kg(-1); d.w.), Ba (4260 mg kg(-1); d.w.) and Hg (1.7 mg kg(-1); d.w.) exceeded the limit values, and therefore the cyclone fly ash cannot be used as an earth construction agent. According to the leached amounts of Cr (38 mg kg(-1); d.w.), Zn (51 mg kg(-1); d.w.) and sulphate (50,000 mg kg(-1); d.w.), the cyclone fly ash is classified as a hazardous waste, and it has to be deposited in a hazardous waste landfill.

Thermal treatment of ashes[Fly Ash from Municipal Waste Incineration]; Termisk rening av askor

Energy Technology Data Exchange (ETDEWEB)

Wikman, Karin; Berg, Magnus; Bjurstroem, Henrik [AaF-Energi och Miljoe AB, Stockholm (Sweden); Nordin, Anders [Umeaa Univ. (Sweden). Dept. of Applied Physics and Electronics

2003-04-01

In this project descriptions of different processes for thermal treatment of ashes have been compiled. A technical and economic evaluation of the processes has been done to identify possibilities and problems. The focus in the project lays on treatment of fly ash from municipal waste incineration but the processes can also be used to treat other ashes. When the ash is heated in the thermal treatment reactor, with or without additives, the material is sintered or vitrified and at the same time volatile substances (Zn, Pb, Cd, Hg etc.) are separated. In general the separation is more effective in processes with reducing conditions compared to oxidizing conditions. Oxidizing processes have both worse separation capacity and require more energy. The oxidizing processes are mainly used to stabilize the ash through vitrification and they are in some cases developed for management of municipal sewage sludge and bottom ash. However, these processes are often not as complex as for example an electric arc melting furnace with reducing conditions. The research today aim to develop more effective electrical melting systems with reducing conditions such as plasma melting furnaces, electric resistance melting furnaces and low frequency induction furnaces. A central question in the evaluation of different thermal treatment processes for ash is how the residues from the treatment can be used. It is not certain that the vitrified material is stable enough to get a high economic value, but it can probably be used as construction material. How the remaining metals in the ash are bound is very important in a long-time perspective. Further studies with leaching tests are necessary to clarify this issue. The heavy metal concentrate from the processes contains impurities, such as chlorine, which makes it unprofitable to obtain the metals. Instead the heavy metal concentrate has to be land filled. However, the amount of material for land filling will be much smaller if only the heavy

Gasification of high ash, high ash fusion temperature bituminous coals

Science.gov (United States)

Liu, Guohai; Vimalchand, Pannalal; Peng, WanWang

2015-11-13

This invention relates to gasification of high ash bituminous coals that have high ash fusion temperatures. The ash content can be in 15 to 45 weight percent range and ash fusion temperatures can be in 1150.degree. C. to 1500.degree. C. range as well as in excess of 1500.degree. C. In a preferred embodiment, such coals are dealt with a two stage gasification process--a relatively low temperature primary gasification step in a circulating fluidized bed transport gasifier followed by a high temperature partial oxidation step of residual char carbon and small quantities of tar. The system to process such coals further includes an internally circulating fluidized bed to effectively cool the high temperature syngas with the aid of an inert media and without the syngas contacting the heat transfer surfaces. A cyclone downstream of the syngas cooler, operating at relatively low temperatures, effectively reduces loading to a dust filtration unit. Nearly dust- and tar-free syngas for chemicals production or power generation and with over 90%, and preferably over about 98%, overall carbon conversion can be achieved with the preferred process, apparatus and methods outlined in this invention.

Ignition technique for an in situ oil shale retort

Science.gov (United States)

Cha, Chang Y.

1983-01-01

A generally flat combustion zone is formed across the entire horizontal cross-section of a fragmented permeable mass of formation particles formed in an in situ oil shale retort. The flat combustion zone is formed by either sequentially igniting regions of the surface of the fragmented permeable mass at successively lower elevations or by igniting the entire surface of the fragmented permeable mass and controlling the rate of advance of various portions of the combustion zone.

Environmental assessment of incinerator residue utilisation

Energy Technology Data Exchange (ETDEWEB)

Toller, Susanna

2008-10-15

In Sweden, utilisation of incinerator residues outside disposal areas is restricted by environmental concerns, as such residues commonly contain greater amounts of potentially toxic trace elements than the natural materials they replace. On the other hand, utilisation can also provide environmental benefits by decreasing the need for landfill and reducing raw material extraction. This thesis provides increased knowledge and proposes better approaches for environmental assessment of incinerator residue utilisation, particularly bottom ash from municipal solid waste incineration (MSWI). A life cycle assessment (LCA) based approach was outlined for environmental assessment of incinerator residue utilisation, in which leaching of trace elements as well as other emissions to air and water and the use of resources were regarded as constituting the potential environmental impact from the system studied. Case studies were performed for i) road construction with or without MSWI bottom ash, ii) three management scenarios for MSWI bottom ash and iii) three management scenarios for wood ash. Different types of potential environmental impact predominated in the activities of the system and the scenarios differed in use of resources and energy. Utilising MSWI bottom ash in road construction and recycling of wood ash on forest land saved more natural resources and energy than when these materials were managed according to the other scenarios investigated, including dumping in landfill. There is a potential for trace element leaching regardless of how the ash is managed. Trace element leaching, particularly of copper (Cu), was identified as being relatively important for environmental assessment of MSWI bottom ash utilisation. CuO is suggested as the most important type of Cu-containing mineral in weathered MSWI bottom ash, whereas in the leachate Cu is mainly present in complexes with dissolved organic matter (DOM). The hydrophilic components of the DOM were more important for Cu

Investigation of rye straw ash sintering characteristics and the effect of additives

International Nuclear Information System (INIS)

Wang, Liang; Skreiberg, Øyvind; Becidan, Michael; Li, Hailong

2016-01-01

Highlights: • Rye straw ash has a high sintering tendency at elevated temperatures. • Addition of additive increases melting temperature of the rye straw ash. • Kaolin addition leads to formation of silicates binding K in the ash. • Calcite and Ca-sludge promotes formation of silicates and phosphates in the ash. • Calcite addition restrains attaching and accumulation of rye straw ash melts. - Abstract: The understanding of ash sintering during combustion of agricultural residues is far from complete, because of the high heterogeneity of the content and composition of ash forming matters and the complex transformation of them. In order to make agricultural residues competitive fuels on the energy market, further research efforts are needed to investigate agricultural residues’ ash sintering behavior and propose relevant anti-sintering measures. The aim of this work was to investigate the ash characteristics of rye straw and effects of additives. Three additives were studied regarding their abilities to prevent and abate rye straw ash sintering. Standard ash fusion characterization and laboratory-scale sintering tests were performed on ashes from mixtures of rye straw and additives produced at 550 °C. Ash residues from sintering tests at higher temperatures were analyzed using a combination of X-ray diffraction (XRD) and scanning electron microscopy–energy dispersive X-ray spectrometry (SEM–EDX). High sintering and melting tendency of the rye straw ash at elevated temperatures was observed. Severe sintering of the rye straw ash was attributed to the formation and fusion of low temperature K–silicates and K–phosphates with high K/Ca ratios. Among the three additives, calcite served the best one to mitigate sintering of the rye straw ash. Ca from the calcite promoted formation of high temperature silicates and calcium rich K–phosphates. In addition, calcite may hinder aggregating of ash melts and further formation of large ash slag. Therefore

Characterization of particulate residues from greenlandic mswi for use as secondary resources

DEFF Research Database (Denmark)

Kirkelund, Gunvor Marie; Dias-Ferreira, Célia; Jensen, Pernille Erland

2016-01-01

In Greenland, waste incineration is used in the larger towns to treat the municipal solid waste. The incineration reduces the amount of waste, but produces particulate incineration residues such as fly and bottom ash that are disposed of. Most construction materials are imported to Arctic areas...... as secondary material. The bottom ashes consisted of coarser particles and exhibited lower heavy metal leaching than the fly ash. All residue samples were different and evaluation of reuse should be made individually, however the fly ash shows potential as cement replacement and bottom ash as sand replacement...

Chromium behavior during thermal treatment of MSW fly ash.

Science.gov (United States)

Kirk, Donald W; Chan, Chris C Y; Marsh, Hilary

2002-02-14

Energy-from-waste incineration has been promoted as an environmentally responsible method for handling non-recyclable waste from households. Despite the benefits of energy production, elimination of organic residues and reduction of volume of waste to be landfilled, there is concern about fly ash disposal. Fly ash from an incinerator contains toxic species such as Pb, Zn, Cd and Cr which may leach into soil and ground water if landfilled. Thermal treatment of the fly ash from municipal solid waste has been tested and proposed as a treatment option for removal of metal species such as Pb, Cd and Zn, via thermal re-volatilization. However, Cr is an element that remains in the residue of the heat treated fly ash and appears to become more soluble. This Cr solubilization is of concern if it exceeds the regulatory limit for hazardous waste. Hence, this unexpected behavior of Cr was investigated. The initial work involved microscopic characterization of Cr in untreated and thermally-treated MSW fly ash. This was followed by determining leaching characteristics using standard protocol leaching tests and characterization leaching methods (sequential extraction). Finally, a mechanism explaining the increased solubilization was proposed and tested by reactions of synthetic chemicals.

Physical, chemical and mineralogical properties of fly ash

International Nuclear Information System (INIS)

Khairul Nizar Ismail; Kamaruddin Hussin; Mohd Sobri Idris

2007-01-01

Fly ash is the finely divided mineral residue resulting from the combustion of coal in electric generating plants. Fly ash consists of inorganic, incombustible matter present in the coal that has been fused during combustion into a glassy, amorphous structure. Fly ash particles are generally spherical in shape and range in size from 2 μm to 10 μm. They consist mostly of silicon dioxide (SiO 2 ), aluminium oxide (Al 2 O 3 ) and iron oxide (Fe 2 O 3 ). Fly ash like soil contains trace concentrations of the following heavy metals: nickel, vanadium, cadmium, barium, chromium, copper, molybdenum, zinc and lead. The chemical compositions of the sample have been examined and the fly ash are of ASTM C618 Class F. (Author)

Thermal treatment of solid residues from WtE units: a review.

Science.gov (United States)

Lindberg, Daniel; Molin, Camilla; Hupa, Mikko

2015-03-01

Thermal treatment methods of bottom ash, fly ash and various types of APC (air pollution control) residues from waste-to-energy plants can be used to obtain environmentally stable material. The thermal treatment processes are meant to reduce the leachability of harmful residue constituents, destroy toxic organic compounds, reduce residue volume, and produce material suitable for utilization. Fly ash and APC residues often have high levels of soluble salts, particularly chlorides, metals such as cadmium, lead, copper and zinc, and trace levels of organic pollutants such as dioxins and furans. Different thermal treatment methods can be used to either decompose or stabilize harmful elements and compounds in the ash, or separate them from the ash to get a material that can be safely stored or used as products or raw materials. In the present paper, thermal treatment methods, such as sintering, vitrification, and melting have been reviewed. In addition to a review of the scientific literature, a survey has been made of the extensive patent literature in the field. Copyright © 2015 Elsevier Ltd. All rights reserved.

Stabilization of plutonium bearing residues at Lawrence Livermore National Laboratory

International Nuclear Information System (INIS)

Bronson, M.C.; Van Konynenburg, R.A.; Ebbinghaus, B.B.

1995-01-01

The US Department of Energy's (US DOE) Lawrence Livermore National Laboratory (LLNL) has plutonium holdings including metal, oxide and residue materials, all of which need stabilization of some type. Residue materials include calcined ash, calcined precipitates, pyrochemical salts, glove box sweepings, metallurgical samples, graphite, and pyrochemical ceramic crucibles. These residues are typical of residues stored throughout the US DOE plutonium sites. The stabilization process selected for each of these residues requires data on chemical impurities, physical attributes, and chemical forms of the plutonium. This paper outlines the characterization and stabilization of LLNL ash residues, pyrochemical salts, and graphite

Effect of composition variations on the long-term wasteform behavior of vitrified domestic waste incineration fly-ash purification residues

International Nuclear Information System (INIS)

Frugier, Pierre

1999-01-01

The effect of variations in the composition of fly-ash purification residue from incinerated domestic waste on the quality of the containment achieved by vitrification was investigated. Three main factors determine the long-term containment quality: the production of a vitrified wasteform, the occurrence of possible crystallization, and the key parameters of long-term alteration in aqueous media. Each of these aspects is described within a composition range defined by variations in the three major elements. (silicon, calcium and aluminum) and two groups of constituents (alkali metals and toxic elements). The silicon fraction in the fly-ash residue was found to be decisive: it is impossible to obtain a satisfactory vitrified wasteform below a given silicon concentration. Compounds with the lowest silica content also exhibited the greatest tendency to crystallize under the cooling conditions prevailing in industrial processes (the dominant crystallized phase is a melilite that occupies a significant fraction of the material and considerably modifies the alteration mechanisms). The initial alteration rate in pure water and the altered glass thickness measured in a closed system at an advanced stage of the dissolution reaction are both inversely related to the silicon concentration in the glass. Several types of long-term behavior were identified according to the composition range, the process conditions and the vitrified waste disposal scenario. Four distinct 'classes' of vitrified wasteform were defined for direct application in industrial processes. (author) [fr

Results from a full scale application of ashes and other residuals in the final cover construction of the Tveta landfill; Utvaerdering av fullskaleanvaendning av askor och andra restprodukter vid sluttaeckning av Tveta Aatervinningsanlaeggning

Energy Technology Data Exchange (ETDEWEB)

Tham, Gustav (Telge AB, Soedertaelje (Sweden)); Andreas, Lale (Luleaa Univ. of Technology, Luleaa (Sweden))

2008-06-15

In 2000 Telge Aatervinning - a waste management and recycling company - started investigating ashes from incineration of industrial and biowaste waste. The company was given a permit from the Swedish Environmental Court to cover four hectares of the house hold waste landfill area. In 2006 the company received an unlimited permit to cover the remaining part of the landfill when the works end some thirty years later. Ashes were used the first time in 1966 for testing. Literature studies indicated the ashes can have a low hydraulic conductivity under certain conditions. In 1999 collaboration started with the Division of Waste Science and Technology at Luleaa University of Technology. Residuals from household and industrial waste were subject to investigation. Initially, biowaste incineration products were subject to testing and were later extended to other waste products, e.g. sludge, contaminated soils, foundry, and compost material. Several different sub-fractions of ashes were included in the investigation e.g. bottom and fly ash, various slag products after up-grading including dewatering, separation and sifting. Subsequently, a complete covering system of a landfill consists of residuals. Six test areas were outlined in order to give a good representation for cover construction in flat and steep areas with different compositions of liner material. The results show that in all areas the hydraulic conductivity construction yields less then 50 liters per square meters and years and can be less the than 5 liters in a repository for hazardous waste if required. In accordance with literature data the field observations show the liner material constructed only by ash material under certain conditions can form a monolithic structure due to very slow processes thus indicating small pore volumes that unable water air to interact with other media. The concept of using ash can be related to natural analogues of volcanic ashes and has been used in old defence walls and other

Distilling bituminous materials

Energy Technology Data Exchange (ETDEWEB)

Forrest, C N; Hayden, H P

1926-12-28

Bituminous materials such as heavy asphaltic residues from petroleum distillation or natural bitumens such as gilsonite, grahamite, etc. are distilled in presence of a carrier consisting of pieces of inert refractory material and by the heat generated by combustion of the coke which remains on the carrier after distillation. A vertical cylindrical retort, in which a wood and coal fire is first made, is charged with an inert refractory substance such as pumice stone, broken firebrick, burnt fire clay, carborundum, ash, etc. mixed with a bituminous substance, which, if fusible, may be melted and added in a rotary drum. The mixture passes downwards through the retort, first through regions in which the hydrocarbons are distilled and cracked and then through a region in which the remaining carbon is burnt by a limited supply of air and steam admitted through a grate. The inert material is discharged through a water seal and used again. Vapors, withdrawn from the retort though an outlet, pass through a heat intercharger and separator and are treated with a spray of sulfuric acid to separate ammonia in a scrubber, with water sprays to condense oil in scrubbers, and with oil in a scrubber.

Characterization on incineration residue of radioactive solid wastes

International Nuclear Information System (INIS)

Katoh, Kiyoshi; Hirayama, Katsuyoshi; Kato, Akira.

1989-01-01

Characterization was carried out on incineration residue discharged from the radioactive solid waste incineration unit (capacity, 100 kg/h) in use at the Tokai Research Establishment of Japan Atomic Energy Research Institute (JAERI) to obtain basic data for investigating solidification methods of the residue. The characterized residue was taken from furnace and a primary ceramic filter of the incineration unit which incinerates combustible solid wastes generated at JAERI and the outside organizations. Items of characterization involve a particle size distribution, misplaced materials content, ignition loss, chemical composition and radioactivity of nuclides in the ash. As the results, the size of ash sampled from the furnace distributed a wide range, with about 35∼60 % of ash smaller than 5 mm and about 10∼25 % of massive one larger than 30 mm (max. size: ∼130 mm). The ignition loss was 2∼3 %. The chemical compositions of the ash were mainly SiO 2 , Fe 2 O 3 , CaO and Al 2 O 3 . The specific activities of the ash were about 0.4∼4 x 10 3 Bq/g, and principal contaminants were 60 Co and 137 Cs. (author)

AL(0) in municipal waste incinerator ash

Science.gov (United States)

Stipp, S. L.; Ronsbo, J. G.; Zunic, T. B.; Christensen, T. H.

2003-04-01

Disposal of municipal waste is a challenge to society. Waste volume is substantially decreased by incineration but residual ash usually contains a number of toxic components which must be immobilised to insure environmental protection. One element, chromium, is mobile and toxic in its oxidised state as Cr(VI) but it can be reduced to Cr(III) and immobilised. Reduction can be promoted by ash treatment with Fe(0) or Fe(II), but recent evidence shows that at least some Cr(VI) is reduced spontaneously in the ash. Aspects of ash behaviour suggest metallic aluminium as the reducing agent, but no direct evidence of Al(0) has been found until now. We examined filter ash from an energy-producing, municipal-waste incinerator (Vest-forbrænding) near Copenhagen. X-ray diffraction (XRD) identified expected salts of Na, K and Ca such as halite, sylvite, calcite, anhydrite and gypsum as well as quartz, feldspar and some hematite. Wave-dispersive electron microprobe produced elemen-tal maps of the ash; Al-rich areas were analysed quantitatively by comparison with standards. We identified metallic Al particles, averaging 50 to 100 micrometers in di-ameter, often with a fractured, glassy border of aluminum oxide. The particles were porous, explaining fast Cr(VI) reduction and they contained thin exsolution lamellae of Al-alloys of Pb and Cu or Mn, Fe and Ag, which provide clues of the Al(0) origin in the waste. Sometimes Al(0) occurred inside glassy globes of Al2O3. Time-of-flight secondary ion mass spectroscopy (TOF-SIMS) and X-ray photoelectron spectroscopy (XPS) proved that surface Al concentrations on ash particles were below detection, confirming reactivity of the Al(0) bulk. The persistence of reduced Al through the highly oxidising combustion procedure comes as a surprise and is a benefit in the immobilisation of Cr(VI) from municipal-waste incineration residues.

Using cotton plant residue to produce briquettes

Energy Technology Data Exchange (ETDEWEB)

Coates, W. [University of Arizona, Tucson, AZ (United States). Bioresources Research Facility

2000-07-01

In Arizona, cotton (Gossypium) plant residue left in the field following harvest must be buried to prevent it from serving as an overwintering site for insects such as the pink bollworm. Most tillage operations employed to incorporate the residue into the soil are energy intensive and often degrade soil structure. Trials showed that cotton plant residue could be incorporated with pecan shells to produce commercially acceptable briquettes. Pecan shell briquettes containing cotton residue rather than waste paper were slightly less durable, when made using equivalent weight mixtures and moisture contents. Proximate and ultimate analyses showed the only difference among briquette samples to be a higher ash content in those made using cotton plant residue. Briquettes made with paper demonstrated longer flame out time, and lower ash percentage, compared to those made with cotton plant residue. (author)

Energy and process substitution in the frozen-food industry: geothermal energy and the retortable pouch

Energy Technology Data Exchange (ETDEWEB)

Stern, M.W.; Hanemann, W.M.; Eckhouse, K.

1981-12-01

An assessment is made of the possibilities of using geothermal energy and an aseptic retortable pouch in the food processing industry. The focus of the study is on the production of frozen broccoli in the Imperial Valley, California. Background information on the current status of the frozen food industry, the nature of geothermal energy as a potential substitute for conventional fossil fuels, and the engineering details of the retortable pouch process are covered. The analytical methodology by which the energy and process substitution were evaluated is described. A four-way comparison of the economics of the frozen product versus the pouched product and conventional fossil fuels versus geothermal energy was performed. A sensitivity analysis for the energy substitution was made and results are given. Results are summarized. (MCW)

Research on Toxicity Evaluation of Waste Incineration Residues of Printed Circuit Boards

Directory of Open Access Journals (Sweden)

Rasa Volungevičienė

2014-10-01

Full Text Available Recycling waste printed circuit boards (PCB is an extremely complicated process, because PCBs consist of a number of complex components – hazardous and non-hazardous materials sets. Pyrolysis and combustion are currently the most effective treatment technologies for waste printed circuit boards. Pyrolysis can be used for thermally decomposing PCBs allowing for the simultaneous recovery of valuable materials. Following the extraction of valuable materials, the problem of residual ash utilization is encountered. Determining the qualitative and quantitative characteristics of incineration residue helps with choosing effective ash management technologies. This paper analyzes PCB ash generated at three different temperatures of 400 °C, 500 °C and 600 °C. Ash residues have been analysed to determine the quantity and type of metals present. Furthermore, the experiment of leaching heavy metals from ash has been described.

Possibilities of municipal solid waste incinerator fly ash utilisation.

Science.gov (United States)

Hartmann, Silvie; Koval, Lukáš; Škrobánková, Hana; Matýsek, Dalibor; Winter, Franz; Purgar, Amon

2015-08-01

Properties of the waste treatment residual fly ash generated from municipal solid waste incinerator fly ash were investigated in this study. Six different mortar blends with the addition of the municipal solid waste incinerator fly ash were evaluated. The Portland cement replacement levels of the municipal solid waste incinerator fly ash used were 25%, 30% and 50%. Both, raw and washed municipal solid waste incinerator fly ash samples were examined. According to the mineralogical composition measurements, a 22.6% increase in the pozzolanic/hydraulic properties was observed for the washed municipal solid waste incinerator fly ash sample. The maximum replacement level of 25% for the washed municipal solid waste incinerator fly ash in mortar blends was established in order to preserve the compressive strength properties. Moreover, the leaching characteristics of the crushed mortar blend was analysed in order to examine the immobilisation of its hazardous contents. © The Author(s) 2015.

Evaluation of heavy metals in hazardous automobile shredder residue thermal residue and immobilization with novel nano-size calcium dispersed reagent.

Science.gov (United States)

Lee, Chi-Hyeon; Truc, Nguyen Thi Thanh; Lee, Byeong-Kyu; Mitoma, Yoshiharu; Mallampati, Srinivasa Reddy

2015-10-15

This study was conducted to synthesize and apply a nano-size calcium dispersed reagent as an immobilization material for heavy metal-contaminated automobile shredder residues (ASR) dust/thermal residues in dry condition. Simple mixing with a nanometallic Ca/CaO/PO4 dispersion mixture immobilized 95-100% of heavy metals in ASR dust/thermal residues (including bottom ash, cavity ash, boiler and bag filter ash). The quantity of heavy metals leached from thermal residues after treatment by nanometallic Ca/CaO/PO4 was lower than the Korean standard regulatory limit for hazardous waste landfills. The morphology and elemental composition of the nanometallic Ca/CaO-treated ASR residue were characterized by field emission scanning election microscopy combined with electron dispersive spectroscopy (FE-SEM/EDS). The results indicated that the amounts of heavy metals detectable on the ASR thermal residue surface decreased and the Ca/PO4 mass percent increased. X-ray diffraction (XRD) pattern analysis indicated that the main fraction of enclosed/bound materials on ASR residue included Ca/PO4- associated crystalline complexes, and that immobile Ca/PO4 salts remarkably inhibited the desorption of heavy metals from ASR residues. These results support the potential use of nanometallic Ca/CaO/PO4 as a simple, suitable and highly efficient material for the gentle immobilization of heavy metals in hazardous ASR thermal residue in dry condition. Copyright © 2015 Elsevier B.V. All rights reserved.

An emerging pollutant contributing to the cytotoxicity of MSWI ash wastes: Strontium

International Nuclear Information System (INIS)

Huang, Wu-Jang; Tang, Hsing-Chuan; Lin, Kae-Long; Liao, Ming-Huei

2010-01-01

In this study, we used the multiple toxicity characteristic leaching procedure to test the long-term leaching behavior of bottom ash, scrubber residue, and baghouse ash from a municipal solid waste incinerator (MSWI). We used the short-term viability percentage of African green monkey kidney cells (Vero cells) as a bioindicator to investigate the cytotoxicity of the leachates from the MSWI ash wastes. We found that strontium was a significant contributor to the cytotoxicity of the bottom ash.

An emerging pollutant contributing to the cytotoxicity of MSWI ash wastes: strontium.

Science.gov (United States)

Huang, Wu-Jang; Tang, Hsing-Chuan; Lin, Kae-Long; Liao, Ming-Huei

2010-01-15

In this study, we used the multiple toxicity characteristic leaching procedure to test the long-term leaching behavior of bottom ash, scrubber residue, and baghouse ash from a municipal solid waste incinerator (MSWI). We used the short-term viability percentage of African green monkey kidney cells (Vero cells) as a bioindicator to investigate the cytotoxicity of the leachates from the MSWI ash wastes. We found that strontium was a significant contributor to the cytotoxicity of the bottom ash.

An emerging pollutant contributing to the cytotoxicity of MSWI ash wastes: Strontium

Energy Technology Data Exchange (ETDEWEB)

Huang, Wu-Jang, E-mail: wjhuang@mail.npust.edu.tw [Department of Environmental Engineering and Science, National Ping-Tung University of Science and Technology, 912 Ping-Tung, Taiwan (China); Tang, Hsing-Chuan [Department of Environmental Engineering and Science, National Ping-Tung University of Science and Technology, 912 Ping-Tung, Taiwan (China); Lin, Kae-Long [Department of Environmental Engineering, National I-Lan University, 260 I-Lan, Taiwan (China); Liao, Ming-Huei [Department of Veterinary Medicine, National Ping-Tung University of Science and Technology, 912 Ping-Tung, Taiwan (China)

2010-01-15

In this study, we used the multiple toxicity characteristic leaching procedure to test the long-term leaching behavior of bottom ash, scrubber residue, and baghouse ash from a municipal solid waste incinerator (MSWI). We used the short-term viability percentage of African green monkey kidney cells (Vero cells) as a bioindicator to investigate the cytotoxicity of the leachates from the MSWI ash wastes. We found that strontium was a significant contributor to the cytotoxicity of the bottom ash.

Alkali activation processes for incinerator residues management.

Science.gov (United States)

Lancellotti, Isabella; Ponzoni, Chiara; Barbieri, Luisa; Leonelli, Cristina

2013-08-01

Incinerator bottom ash (BA) is produced in large amount worldwide and in Italy, where 5.1 millionstons of municipal solid residues have been incinerated in 2010, corresponding to 1.2-1.5 millionstons of produced bottom ash. This residue has been used in the present study for producing dense geopolymers containing high percentage (50-70 wt%) of ash. The amount of potentially reactive aluminosilicate fraction in the ash has been determined by means of test in NaOH. The final properties of geopolymers prepared with or without taking into account this reactive fraction have been compared. The results showed that due to the presence of both amorphous and crystalline fractions with a different degree of reactivity, the incinerator BA geopolymers exhibit significant differences in terms of Si/Al ratio and microstructure when reactive fraction is considered. Copyright © 2013 Elsevier Ltd. All rights reserved.

Why is Coal Ash of Concern and How to Assess Potential Impacts?

Science.gov (United States)

EPA's new test methods - the leaching environmental assessment framework (LEAF) are discussed including how they have been used to evaluate fly ash and scrubber residues. Work to evaluate high-volume encapsulated use of fly ash in cementitious material is also described.

Recovery of plutonium from incinerator ash at Rocky Flats

International Nuclear Information System (INIS)

Johnson, T.C.

1976-01-01

Incineration of combustible materials highly contaminated with plutonium produces a residue of incinerator ash. Recovery of plutonium from incinerator ash residues at Rocky Flats is accomplished by a continuous leaching operation with nitric acid containing fluoride ion. Special equipment used in the leaching operation consists of a screw feeder, air-lift dissolvers, filters, solids dryer, and vapor collection system. Each equipment item is described in detail. The average dissolution efficiency of plutonium experienced with the process was 68% on the first pass, 74% on the second pass, and 64% on each subsequent pass. Total-solids dissolution efficiencies averaged 47% on the first pass and about 25% on each subsequent pass

Regular Recycling of Wood Ash to Prevent Waste Production (RecAsh). Technical Final Report

Energy Technology Data Exchange (ETDEWEB)

Andersson, Lars E-mail: lars.t.andersson@skogsstyreslen.se

2007-03-15

At present, the extraction of harvest residues is predicted to increase in Sweden and Finland. As an effect of the intensified harvesting, the export of nutrients and acid buffering substances from the growth site is also increased. Wood ash could be used to compensate forest soils for such losses. Most wood fuel ash is today often deposited in landfills. If the wood ash is recycled, wood energy is produced without any significant waste production. Ash recycling would therefore contribute to decreasing the production of waste, and to maintaining the chemical quality of forest waters and biological productivity of forest soils in the long term. The project has developed, analysed and demonstrated two regular ash-recycling systems. It has also distributed knowledge gathered about motives for ash recycling as well as technical and administrative solutions through a range of media (handbooks, workshops, field demonstrations, reports, web page and information videos). Hopefully, the project will contribute to decreasing waste problems related to bio-energy production in the EU at large. The project has been organised as a separate structure at the beneficiary and divided in four geographically defined subprojects, one in Finland and three in Sweden (Central Sweden, Northern Sweden, and South-western Sweden). The work in each subproject has been lead by a subproject leader. Each subproject has organised a regional reference group. A project steering committee has been established consisting of senior officials from all concerned partners. The project had nine main tasks with the following main expected deliverables and output: 1. Development of two complete full-scale ash-recycling systems; 2. Production of handbooks of the ash recycling system; 3. Ash classification study to support national actions for recommendations; 4. Organise regional demonstrations of various technical options for ash treatment and spreading; 5. Organise national seminars and demonstrations of

Hot gas stripping of ammonia and carbon dioxide from simulated and actual in situ retort waters

Energy Technology Data Exchange (ETDEWEB)

Murphy, C.L.

1979-01-01

This study proved that ammonia and carbon dioxide could be removed from retort water by hot gas stripping and that overall transfer rates were slower than for physical desorption alone. The ammonia in solution complexed with the carbonate species with the result that the CO/sub 2/ transfer rates were linked to the relatively slower desorption of NH/sub 3/ from solution. Ionic reactions in the liquid phase limited the quantity of free NH/sub 3/ and CO/sub 2/, thus decreasing the driving forces for mass transfer. The retort water exhibited foaming tendencies that affected the interfacial area which should be taken into account if a stripping tower is considered on a larger scale. Transfer unit heights were calculated for the process conditions studied and correlated such that scaleup to increased capacities is possible.

Utilisation aspects of ashes and green liquor dregs from an integrated semichemical pulp and board mill

Energy Technology Data Exchange (ETDEWEB)

Manskinen, K.

2013-09-01

This thesis investigated the properties of bottom and fly ashes originating from a bubbling fluidised bed boiler (120 MW) using two different fuel mixtures (i.e. Fuel mixture A: coal, wood and peat; and B: wood and peat) and of the green liquor dregs originating from the associated semichemical pulp and board mill in relation to the potential utilisation of these residues from various aspects. The total concentrations of As, Cd, Cr, Cu, Ni, Pb, Zn and Hg in the bottom ashes were lower than the maximum allowable concentrations for these elements in forest fertilisers. The total Ca concentrations in bottom ashes A (2.4%; d.w.) and B (3.4%; d.w.) were lower than the legal requirement of 6.0% (d.w.) for ash used as a forest fertiliser. The total Ca concentrations in fly ashes A (6.4%; d.w.) and B (11.0%; d.w.) were higher than the minimum limit value of 6.0% (d.w.), but the concentration of As in fly ashes A (46.9 mg/kg d.w.) and B (41.3 mg/kg; d.w.) exceeded the maximum limit value of 40 mg/kg (d.w.). Only bottom ash B could be used as a forest fertiliser, provided some additional Ca is used. The bottom ashes both fulfilled the Finnish regulations on waste recovery in earth construction. Due to the elevated total concentration of PAH (23 mg/kg; d.w.) and extractable concentrations of Mo (3.9 mg/kg; d.w.) and Se (0.2 mg/kg; d.w.) in fly ash A, this residue cannot be used in covered structures. Due to the elevated concentration of PAH (90 mg/kg; d.w.) in fly ash B, this residue cannot be used in covered and paved structures. However, the utilisation of these residues as an earth construction agent is still possible, but an environmental permit would be required. According to the sequential extraction studies, extractable concentrations of most of the elements in the fly ash A were higher than those in the bottom ash A. The extractability of various elements, both in the bottom and fly ashes A, varied widely. Most of the elements did not occur as readily soluble and

Coal ash usage in environmental restoration at the Hanford site

Energy Technology Data Exchange (ETDEWEB)

Scanlon, P.L.; Sonnichsen, J.C.; Phillips, S.J.

1994-08-01

The ash stockpiled next to the 284E steam plant is mixed fly ash, bottom ash, and slag. The ash consists of (1) baghouse residue and (2) a mixture of bottom ash and slag which is washed out of the bottom of the boilers daily. In 1991, a Toxicity Characteristic Leaching Procedure (TCLP) was performed on several samples of this ash (Hazen Research 1991). This procedure is designed to determine the mobility of organic and inorganic anatytes present in liquid, solid, or multiphasic wastes (EPA 1994). The ash tested came from surge bins, conveyor samples, and bottom ash and fly ash from the boilers at 284E. Antimony, cadmium, germanium, molybdenum, silver, thallium, tungsten, and vanadium were tested for, but on all samples were below detection Limits for the testing method. Analytes present in relatively high concentrations (but less than one part per thousand) included barium, boron, chromium, fluorine, and zinc. The size of ash particles passing through a Taylor sieve series was very evenly distributed from 1 to 200m.

Retort for distilling oil from shales and other fuels

Energy Technology Data Exchange (ETDEWEB)

Wood, E C

1931-04-17

A retort is constructed in the form of a flat shallow covered conduit through which the fuel in a pulverized form is continuously conveyed on a train of pans so loaded as to completely fill the conduit, heat being applied to an adequate central portion of the conduit to effect the distillation of the fuel. The roof or cover is sufficiently higher for the extent of such heated portion to afford space for and thereby facilitate the offtake of the distillation products while the ends of the conduit remain sealed against the escape of such products.

Calcium phosphate stabilization of fly ash with chloride extraction.

Science.gov (United States)

Nzihou, Ange; Sharrock, Patrick

2002-01-01

Municipal solid waste incinerator by products include fly ash and air pollution control residues. In order to transform these incinerator wastes into reusable mineral species, soluble alkali chlorides must be separated and toxic trace elements must be stabilized in insoluble form. We show that alkali chlorides can be extracted efficiently in an aqueous extraction step combining a calcium phosphate gel precipitation. In such a process, sodium and potassium chlorides are obtained free from calcium salts, and the trace metal ions are immobilized in the calcium phosphate matrix. Moderate calcination of the chemically treated fly ash leads to the formation of cristalline hydroxylapatite. Fly ash spiked with copper ions and treated by this process shows improved stability of metal ions. Leaching tests with water or EDTA reveal a significant drop in metal ion dissolution. Hydroxylapatite may trap toxic metals and also prevent their evaporation during thermal treatments. Incinerator fly ash together with air pollution control residues, treated by the combined chloride extraction and hydroxylapatite formation process may be considered safe to use as a mineral filler in value added products such as road base or cement blocks.

Some aspects of the technology improvement for heat reprocessing of the combustible radioactive wastes and ash residue conditioning

International Nuclear Information System (INIS)

Dmitriev, S.A.; Lifanov, F.A.; Knyazev, I.A.; Buravchenko, N.N.; Sobolev, I.A.; Mamaev, L.A.; Alekseev, A.N.; Simagina, O.S.

1991-01-01

The results of studies devoted to increasing the efficiency of thermal reprocessing (combustion) of organic low- and intermediate-level radioactive wastes are given. The new most efficient three-stage process including: 1) gasification and pyrolysis of an organic material with volatile product release, 2) coke residual combustion, ash and noncombustible materials melting, 3) combustion of volatile products of thermal decomposition is developed on the basis of the analysis of solid radioactive waste combustion schemes, mathematical simulation and laboratory studies. Experimental bed, in which these processes are realized, is created. The results obtained in it have allowed one to begin designing of the pilot-commercial plant with shaft furnace having the capacity up to 200 kg/h for solid wastes

Fundamental study of low-NOx combustion fly ash utilization

International Nuclear Information System (INIS)

Suuberg, Eric M.; Hurt, Robert H.

1998-01-01

This study is principally concerned with characterizing the organic part of coal combustion fly ashes. High carbon fly ashes are becoming more common as by-products of low-NOx combustion technology, and there is need to learn more about this fraction of the fly ash. The project team consists of two universities, Brown and Princeton, and an electrical utility, New England Power. A sample suite of over fifty fly ashes has been gathered from utilities across the United States, and includes ashes from a coals ranging in rank from bituminous to lignite. The characterizations of these ashes include standard tests (LOI, Foam Index), as well as more detailed characterizations of their surface areas, porosity, extractability and adsorption behavior. The ultimate goal is, by better characterizing the material, to enable broadening the range of applications for coal fly ash re-use beyond the current main market as a pozzolanic agent for concretes. The potential for high carbon-content fly ashes to substitute for activated carbons is receiving particular attention. The work performed to date has already revealed how very different the surfaces of different ashes produced by the same utility can be, with respect to polarity of the residual carbon. This can help explain the large variations in acceptability of these ashes as concrete additives

Mobility of organic carbon from incineration residues

International Nuclear Information System (INIS)

Ecke, Holger; Svensson, Malin

2008-01-01

Dissolved organic carbon (DOC) may affect the transport of pollutants from incineration residues when landfilled or used in geotechnical construction. The leaching of dissolved organic carbon (DOC) from municipal solid waste incineration (MSWI) bottom ash and air pollution control residue (APC) from the incineration of waste wood was investigated. Factors affecting the mobility of DOC were studied in a reduced 2 6-1 experimental design. Controlled factors were treatment with ultrasonic radiation, full carbonation (addition of CO 2 until the pH was stable for 2.5 h), liquid-to-solid (L/S) ratio, pH, leaching temperature and time. Full carbonation, pH and the L/S ratio were the main factors controlling the mobility of DOC in the bottom ash. Approximately 60 weight-% of the total organic carbon (TOC) in the bottom ash was available for leaching in aqueous solutions. The L/S ratio and pH mainly controlled the mobilization of DOC from the APC residue. About 93 weight-% of TOC in the APC residue was, however, not mobilized at all, which might be due to a high content of elemental carbon. Using the European standard EN 13 137 for determination of total organic carbon (TOC) in MSWI residues is inappropriate. The results might be biased due to elemental carbon. It is recommended to develop a TOC method distinguishing between organic and elemental carbon

Aggregate material formulated with MSWI bottom ash and APC fly ash for use as secondary building material

International Nuclear Information System (INIS)

Valle-Zermeño, R. del; Formosa, J.; Chimenos, J.M.; Martínez, M.; Fernández, A.I.

2013-01-01

Highlights: ► A concrete formulation was optimized using Bottom Ash and APC ash. ► 10% of APC ash achieves good compromise between economic and performance aspects. ► The crushed concrete was evaluated as secondary building granular material. ► The environmental behavior allows its use as secondary material. ► The abrasion resistance is not good enough for its use as a road sub-base material. - Abstract: The main goal of this paper is to obtain a granular material formulated with Municipal Solid Waste Incineration (MSWI) bottom ash (BA) and air pollution control (APC) fly ash to be used as secondary building material. Previously, an optimum concrete mixture using both MSWI residues as aggregates was formulated. A compromise between the environmental behavior whilst maximizing the reuse of APC fly ash was considered and assessed. Unconfined compressive strength and abrasion resistance values were measured in order to evaluate the mechanical properties. From these results, the granular mixture was not suited for certain applications owing to the high BA/APC fly ash content and low cement percentages used to reduce the costs of the final product. Nevertheless, the leaching test performed showed that the concentrations of all heavy metals were below the limits established by the current Catalan legislation for their reutilization. Therefore, the material studied might be mainly used in embankments, where high mechanical properties are not needed and environmental safety is assured

Instrumental neutron activation analysis of coal and its combustion residues from a power plant

International Nuclear Information System (INIS)

Lim, J.M.; Jeong, J.H.; Lee, J.H.

2013-01-01

A growing demand of electrical energy derived from coal combustion led to a significant increase of coal ash as residues. Approximately 70 % of the fly ashes are recycled, while most of the bottom ashes have been land-filled in the ash pond in Korea. In this work, to evaluate the potential impacts of the residues from a coal power plant on the environment, its inorganic elemental components were determined by INAA and PGAA. Coal ash samples were collected from the biggest power plant complex in Korea. These samples were analyzed by using the NAA facilities in the HANARO research reactor of the Korea Atomic Energy Research Institute. A total of 31 elements were analyzed in the samples, and certified reference materials were used for the analytical quality control. The enrichment status of a given metal in fuel coal and ashes was investigated by its concentration ratio. In order to assess the impact of the coal combustion residues on ecosystem, their concentrations determined for each respective type of the samples were compared to both reference data and nearby beach sand samples. (author)

Reduction of Aspergillus spp. and aflatoxins in peanut sauce processing by oil-less frying of chilli powder and retort processing.

Science.gov (United States)

Farawahida, A H; Jinap, S; Nor-Khaizura, M A R; Samsudin, N I P

2017-12-01

Among the many roles played by small and medium enterprises (SMEs) in the food industry is the production of heritage foods such as peanut sauce. Unfortunately, the safety of peanut sauce is not always assured as the processing line is not controlled. Peanut sauce is usually made of peanuts and chilli, and these commodities are normally contaminated with Aspergillus spp. and aflatoxins (AFs). Hence, the objective of this study was to evaluate the practices related to reduction of AF hazard and the effect of interventions in peanut sauce processing. Peanut samples were collected from each step of peanut sauce processing from a small peanut sauce company according to four designs: (1) control; (2) oil-less frying of chilli powder; (3) addition of retort processing; and (4) combination of oil-less frying of chilli powder and retort processing. Oil-less frying of chilli powder (Design 2) reduced total AFs by 33-41%, retort processing (Design 3) reduced total AFs by 49%, while combination of these two thermal processes (Design 4) significantly reduced total AFs, by 57%. The present work demonstrated that Design 4 yielded the highest reduction of total AFs and is therefore recommended to be employed by SME companies.

Aggregate material formulated with MSWI bottom ash and APC fly ash for use as secondary building material.

Science.gov (United States)

del Valle-Zermeño, R; Formosa, J; Chimenos, J M; Martínez, M; Fernández, A I

2013-03-01

The main goal of this paper is to obtain a granular material formulated with Municipal Solid Waste Incineration (MSWI) bottom ash (BA) and air pollution control (APC) fly ash to be used as secondary building material. Previously, an optimum concrete mixture using both MSWI residues as aggregates was formulated. A compromise between the environmental behavior whilst maximizing the reuse of APC fly ash was considered and assessed. Unconfined compressive strength and abrasion resistance values were measured in order to evaluate the mechanical properties. From these results, the granular mixture was not suited for certain applications owing to the high BA/APC fly ash content and low cement percentages used to reduce the costs of the final product. Nevertheless, the leaching test performed showed that the concentrations of all heavy metals were below the limits established by the current Catalan legislation for their reutilization. Therefore, the material studied might be mainly used in embankments, where high mechanical properties are not needed and environmental safety is assured. Copyright © 2012 Elsevier Ltd. All rights reserved.

Assessing fly ash treatment: remediation and stabilization of heavy metals.

Science.gov (United States)

Lima, A T; Ottosen, Lisbeth M; Ribeiro, Alexandra B

2012-03-01

Fly ashes from Municipal Solid Waste (MSW), straw (ST) and co-combustion of wood (CW) are here analyzed with the intent of reusing them. Two techniques are assessed, a remediation technique and a solidification/stabilization one. The removal of heavy metals from fly ashes through the electrodialytic process (EDR) has been tried out before. The goal of removing heavy metals has always been the reuse of fly ash, for instance in agricultural fields (BEK). The best removal rates are here summarized and some new results have been added. MSW fly ashes are still too hazardous after treatment to even consider application to the soil. ST ash is the only residue that gets concentrations low enough to be reused, but its fertilizing value might be questioned. An alternative reuse for the three ashes is here preliminary tested, the combination of fly ash with mortar. Fly ashes have been substituted by cement fraction or aggregate fraction. Surprisingly, better compressive strengths were obtained by replacing the aggregate fraction. CW ashes presented promising results for the substitution of aggregate in mortar and possibly in concrete. Copyright © 2010 Elsevier Ltd. All rights reserved.

Assessing fly ash treatment: Remediation and stabilization of heavy metals

KAUST Repository

Lima, A.T.

2010-12-17

Fly ashes from Municipal Solid Waste (MSW), straw (ST) and co-combustion of wood (CW) are here analyzed with the intent of reusing them. Two techniques are assessed, a remediation technique and a solidification/stabilization one. The removal of heavy metals from fly ashes through the electrodialytic process (EDR) has been tried out before. The goal of removing heavy metals has always been the reuse of fly ash, for instance in agricultural fields (BEK). The best removal rates are here summarized and some new results have been added. MSW fly ashes are still too hazardous after treatment to even consider application to the soil. ST ash is the only residue that gets concentrations low enough to be reused, but its fertilizing value might be questioned. An alternative reuse for the three ashes is here preliminary tested, the combination of fly ash with mortar. Fly ashes have been substituted by cement fraction or aggregate fraction. Surprisingly, better compressive strengths were obtained by replacing the aggregate fraction. CW ashes presented promising results for the substitution of aggregate in mortar and possibly in concrete. © 2010 Elsevier Ltd.

Assessing fly ash treatment: Remediation and stabilization of heavy metals

KAUST Repository

Lima, A.T.; Ottosen, Lisbeth M.; Ribeiro, Alexandra B.

2010-01-01

Fly ashes from Municipal Solid Waste (MSW), straw (ST) and co-combustion of wood (CW) are here analyzed with the intent of reusing them. Two techniques are assessed, a remediation technique and a solidification/stabilization one. The removal of heavy metals from fly ashes through the electrodialytic process (EDR) has been tried out before. The goal of removing heavy metals has always been the reuse of fly ash, for instance in agricultural fields (BEK). The best removal rates are here summarized and some new results have been added. MSW fly ashes are still too hazardous after treatment to even consider application to the soil. ST ash is the only residue that gets concentrations low enough to be reused, but its fertilizing value might be questioned. An alternative reuse for the three ashes is here preliminary tested, the combination of fly ash with mortar. Fly ashes have been substituted by cement fraction or aggregate fraction. Surprisingly, better compressive strengths were obtained by replacing the aggregate fraction. CW ashes presented promising results for the substitution of aggregate in mortar and possibly in concrete. © 2010 Elsevier Ltd.

ADSORPTION OF THE DYE REACTIVE BLUE 5G IN RETORTED SHALE

OpenAIRE

Lambrecht, R.; Barros, M. A. S. D. de; Arroyo, P. A.; Borba, C. E.; Silva, E. A. da

2015-01-01

Abstract In this study the influence of the volumetric flow rate and feed concentration was investigated for the adsorption of the reactive dye Blue 5G. Experiments were carried out in a bed packed with retorted shale, at 30 ºC. The ranges investigated were flow rate 2 -10 mL/min and the feed concentration 13-105 mg/L. Mathematical models were used to represent the dynamic sorption. The double resistance model considers the effects of the axial dispersion and the mass transfer resistance...

Radioactivity of combustion residues from coal-fired power stations

International Nuclear Information System (INIS)

Vom Berg, W.; Puch, K.H.

1996-01-01

Each year in Germany, about 18 mill. t of combustion residues are produced from the combustion of bituminous coal and lignite. They are utilized to a great extent in the construction industry and in mining. During the combustion of coal, the radio-nuclides remain predominantly in the ash. The radionuclide concentration in lignite ash is within the range of that in natural soil. The combustion residues of bituminous coal contain radio-nuclides of a similar order of magnitude as also can occur in natural rock. The utilization of combustion residues in construction materials makes a negligible contribution to radiation exposure through retention in buildings. (orig.) [de

Recovery of plutonium from pyrolysis and incineration residues

International Nuclear Information System (INIS)

Isaacs, J.W.; McDonald, L.A.; Roberts, W.G.; Sutcliffe, P.W.; Wilkins, J.D.

1981-01-01

The effect of ashes prepared from typical plutonium-handling, glove box, combustible wastes on the dissolution of PuO 2 is described. Synthetic ashes have been prepared by doping inactively-prepared ashes with various plutonium-containing compounds, followed by heating at temperatures in the range 550-1200 0 C. The resulting ashes have been leach-tested in order to provide information on the relationship between leachability, the nature of the ashes, the type of plutonium contamination and temperature of thermal treatment. Optimum temperatures for the recovery of plutonium and for the production of inert ''slag'' -type residues have been identified. A furnace for producing model incinerator ashes and pyrolysis chars under carefully controlled conditions is described. Preliminary results on the leaching of these plutonium-active ashes and chars are discussed. (author)

Alkaline coal fly ash amendments are recommended for improving rice-peanut crops

Energy Technology Data Exchange (ETDEWEB)

Swain, D.K.; Ghosh, B.C. [Agricultural and Food Engineering Department, Indi an Inst. of Technology, Kharagpur, West Bengal (India); Rautaray, S.K. [RRLRRS, Gerua Via-Hajo, Dist-Kamrup, Assam (India)

2007-05-15

A field experiment investigating amendments of organic material including farmyard manure, paper factory sludge and crop residues combined with fly ash, lime and chemical fertilizer in a rice-peanut cropping system was conducted during 1997-98 and 1998-99 at the Indian Institute of Technology, Kharagpur, India. The soil was an acid lateritic (Halustaf) sandy loam. For rice, an N:P:K level of 90:26.2:33.3 kg/ha was supplied through the organic materials and chemical fertilizer to all the treatments except control and fly ash alone. The required quantities of organic materials were added to supply 30 kg N/ha and the balance amount of N, P and K was supplied through chemical fertilizer. Amendment materials as per fertilization treatments were incorporated to individual plots 15 days before planting of rice during the rainy season. The residual effects were studied on the following peanut crop with application of N:P:K at 30:26.2:33.3 kg/ha through chemical fertilizer alone in all treatments, apart from the control. An application of fly ash at 10 t/ha in combination with chemical fertilizer and organic materials increased the grain yield of rice by 11% compared to chemical fertilizer alone. The residual effect of both lime and fly ash applications combined with direct application of chemical fertilizer increased peanut yields by 30% and 24%, respectively, compared to chemical fertilizer alone. Treatments with fly ash or lime increased P and K uptake in both the crops and oil content in peanut kernel compared to those without the amendments. Alkaline coal fly ash proved to be a better amendment than lime for improving productivity of an acid lateritic soil and enriching the soil with P and K.

Extraction of toxic and valuable metals from wastewater sludge and ash arising from RECICLAGUA, a treatment plant for residual waters applying the leaching technique

International Nuclear Information System (INIS)

Guerrero D, J.J.

2004-01-01

Presently work, the technique is applied of having leached using coupled thermostatted columns, the X-ray diffraction for the identification of the atomic and molecular structure of the metals toxic that are present in the residual muds of a treatment plant of water located in the municipality of the Estado de Mexico, RECICLAGUA, likewise the techniques is used of Inductively Coupled Plasma Mass Spectroscopy and X-ray fluorescence analysis for the qualitative analysis. We took samples of residual sludge and incinerated ash of a treatment plant waste water from the industrial corridor Toluca-Lerma RECICLAGUA, located in Lerma, Estado de Mexico. For this study 100 g. of residual of sludge mixed with a solution to 10% of mineral acid or sodium hydroxide according to the case, to adjust the one p H at 2, 5, 7 and 10, bisulfite was added, of 0.3-1.5 g of dodecyl sulfate of sodium and 3.93 g of DTPA (triple V). Diethylene triamine penta acetate. These sludges and ashes were extracted from toxic and valuable metals by means of the leaching technique using coupled thermostated columns that which were designed by Dr. Jaime Vite Torres, it is necessary to make mention that so much the process as the apparatus with those that one worked was patented by him same. With the extraction of these metals, benefits are obtained, mainly of economic type, achieving the decrease of the volume of those wastes that have been generated; as well as the so much use of those residuals, once the metals have been eliminated, as of those residuals, once the metals have been eliminated, as of those liquors, the heavy metals were extracted. It was carried out a quantitative analysis using Icp mass spectroscopy, this way to be able to know the one content of the present metals in the samples before and after of leaching them, these results reported a great quantity of elements. Another of the techniques employees was the analysis by X-ray diffraction that provides an elementary content of the

The Netherlands, guide to ash-utilization: Novem's contribution

International Nuclear Information System (INIS)

Stork, J.

1991-01-01

The production of fly ash in coal-fired utility plants in Sweden has more than doubled since 1983 although in future gasification slag and sulphur will be the most prolific waste products as clean coal technologies are introduced. About 50% of fly ash produced is shipped to Belgium and France for use in the cement industry; bottom ash is used for road construction in France and as a concrete filler in Belgium; a large percentage of gypsum is used in Belgium, France and Germany for making wall boards. Novem's programme to investigate the various applications of coal residues in the building industry is described. The three-phase programme involves investigation of the market for products, research into application of fly ash in the cement sector and for artificial gravel and sand-lime bricks. The Kaldin demonstration project on the uses of waste limestone is mentioned

Wildfire ash: its production and hydro-eco-geomorphic effects in forested landscapes

Science.gov (United States)

Doerr, S. H.; Bodi, M.; Santin, C.; Balfour, V.; Woods, S.; Mataix-Solera, J.; Cerda, A.; Shakesby, R.

2012-12-01

Fire, whether ignited naturally or by humans, is one of the most important disturbance agents in many of the world's forested ecosystems. Amongst its direct consequences is the deposition of a range of solid and largely powdery residues on the ground consisting of charred organic material including charcoal and residual mineral material. This fragile 'ash' layer can be removed in large quantities from hillslopes within days by wind or water erosion, with the latter facilitating its transfer to the hydrological system. Probably as a result of its ephemeral nature and not being soil, vegetation or litter, ash has seen limited attention in studies on hydrological impacts of wildfire. Those few studies available show that ash can substantially affect the hydrological system. When present on hillslopes as a water-absorbent layer, it can reduce surface runoff, protect soil against rainsplash erosion, and its leachates can reportedly reduce soil erodibility by promoting flocculation of dispersed clays. In contrast, however, ash can also increase surface runoff by blocking soil pores or by forming a crust. Furthermore, ash is thought capable of promoting debris flows. Its net effect probably depends on the nature of the ash and soil including their respective water repellency levels, the pore size distribution of the soil, and general terrain and rainfall characteristics. Being very mobile, ash can be the source of substantial organic and inorganic sediment inputs, and of solute influxes into the fluvial system. These can affect water quality sometimes with detrimental effects on aquatic organisms and domestic water supply. This presentation aims to provide an overview of the current knowledge base regarding the production and potential effects of wildfire ash on the hydrological system in and beyond forested landscapes..The late Scott Woods examining a thick ash layer following a severe fire in a conifer forest. Montana, USA.

Coal ash fusion temperatures -- New characterization techniques, and associations with phase equilibria

Energy Technology Data Exchange (ETDEWEB)

Wall, T.F.; Gupta, R.P.; Gupta, S. [Univ. of Newcastle, New South Wales (Australia). Dept. of Chemical Engineering; Creelman, R.A. [R.A. Creelman and Associates, Epping, New South Wales (Australia); Coin, C. [ACIRL Ipswich, Booval, Queensland (Australia); Lowe, A. [Pacific Power, Sydney, New South Wales (Australia)

1996-12-31

The well-documented shortcomings of the standard technique for estimating the fusion temperature of coal ash are its subjective nature and poor accuracy. Alternative measurements based on the shrinkage and electrical conductivity of heating samples are therefore examined with laboratory ash prepared at about 800 C in crucibles, as well as combustion ash sampled from power stations. Sensitive shrinkage measurements indicate temperatures of rapid change which correspond to the formation of liquid phases that can be identified on ternary phase diagrams. The existence and extent of formation of these phases, as quantified by the magnitude of peaks in the test, provide alternative ash fusion temperatures. The peaks from laboratory ashes and corresponding combustion ashes derived from the same coals show clear differences which may be related to the evaporation of potassium during combustion and the reactions of the mineral residues to form combustion ash.

Method for establishing a combustion zone in an in situ oil shale retort having a pocket at the top

Science.gov (United States)

Cha, Chang Y.

1980-01-01

An in situ oil shale retort having a top boundary of unfragmented formation and containing a fragmented permeable mass has a pocket at the top, that is, an open space between a portion of the top of the fragmented mass and the top boundary of unfragmented formation. To establish a combustion zone across the fragmented mass, a combustion zone is established in a portion of the fragmented mass which is proximate to the top boundary. A retort inlet mixture comprising oxygen is introduced to the fragmented mass to propagate the combustion zone across an upper portion of the fragmented mass. Simultaneously, cool fluid is introduced to the pocket to prevent overheating and thermal sloughing of formation from the top boundary into the pocket.

Effect of industrial residue combinations on availability of elements

Energy Technology Data Exchange (ETDEWEB)

Brännvall, Evelina, E-mail: evelina.brannvall@ltu.se [Waste Science and Technology, Luleå University of Technology, 97187 Luleå (Sweden); Zamora, Carles Belmonte [Waste Science and Technology, Luleå University of Technology, 97187 Luleå (Sweden); Sjöblom, Rolf [Waste Science and Technology, Luleå University of Technology, 97187 Luleå (Sweden); Tekedo AB, Spinnarvägen 10, 611 37 Nyköping (Sweden); Kumpiene, Jurate [Waste Science and Technology, Luleå University of Technology, 97187 Luleå (Sweden)

2014-07-15

Highlights: • Beneficial combination of fly ash and biosolids. • Nutrient availability increase. • Potentially toxic element availability decrease. • Measured element availability was differed from the calculated leaching potential. - Abstract: Industrial residues, such as fly ashes and biosolids, contain elements (e.g., N, P, K, S, Ca and Zn) that make them a viable alternative for synthetic fertilizers in forestry and agriculture. However, the use of these materials is often limited due to the presence of potentially toxic substances. It is therefore necessary to assess and, when warranted, modify the chemical and physical form of these and similar waste materials before any advantages are taken of their beneficial properties. Biofuel fly ash, municipal solid waste incineration (MSWI) fly ash, biosolids, peat, peat residues and gypsum board waste were combined in various proportions, and this resulted in increased leaching of N, P, S, Cu and Mn, but decreased leaching of Ca, K, Mg, Cr, Fe, Ni, Zn, Al, As and Pb. Chemical fractionation revealed that elements Ca, K, Mg, S and Mn were predominantly exchangeable, while the rest of the elements were less mobile. Cadmium was mostly exchangeable in MSWI fly ash, but less mobile in biofuel fly ash mixtures. Recycling of MSWI fly ash in the mixtures with fertilizers is considerably less attractive, due to the high levels of salts and exchangeable Cd.

Cement production from coal conversion residues

International Nuclear Information System (INIS)

Brown, L.D.; Clavenna, L.R.; Eakman, J.M.; Nahas, N.C.

1981-01-01

Cement is produced by feeding residue solids containing carbonaceous material and ash constituents obtained from converting a carbonaceous feed material into liquids and/or gases into a cement-making zone and burning the carbon in the residue solids to supply at least a portion of the energy required to convert the solids into cement

Development of Mitsui/Juelich Incineration System and hydro-thermal ash solidification

International Nuclear Information System (INIS)

Suzuki, S.; Kamada, S.; Nakamori, Y.; Katakura, M.; Yamazaki, N.

1988-01-01

This paper summarizes the developing program for Mitsui/Juelich Incinerated System combined with Hydrothermal ash solidification. The system is an integrated one and capable for volume reduction of various kind of radioactive waste and safe disposal of residual incinerator ash. The system also has an advantage of reducing construction and operation cost. An outline of the incineration plant is also presented in this paper

Evaluation of heavy metals in hazardous automobile shredder residue thermal residue and immobilization with novel nano-size calcium dispersed reagent

International Nuclear Information System (INIS)

Lee, Chi-Hyeon; Truc, Nguyen Thi Thanh; Lee, Byeong-Kyu; Mitoma, Yoshiharu; Mallampati, Srinivasa Reddy

2015-01-01

Graphical abstract: Schematic representation of possible mechanisms determining the heavy metals immobilization efficiencyof ASR dust/thermal residues after treatment with nanometallic Ca/CaO/PO 4 . - Highlights: • Nanometallic Ca/CaO/PO 4 for heavy metals immobilization in ASR residue. • Heavy metals immobilization in dry condition attained about 95–100%. • Remaining heavy metals were lower than the Korean standard regulatory limit. • The amounts of heavy metals detectable on the ASR dust surface decreased. • Nanometallic Ca/CaO/PO 4 has a promising potential for heavy metal remediation. - Abstract: This study was conducted to synthesize and apply a nano-size calcium dispersed reagent as an immobilization material for heavy metal-contaminated automobile shredder residues (ASR) dust/thermal residues in dry condition. Simple mixing with a nanometallic Ca/CaO/PO 4 dispersion mixture immobilized 95–100% of heavy metals in ASR dust/thermal residues (including bottom ash, cavity ash, boiler and bag filter ash). The quantity of heavy metals leached from thermal residues after treatment by nanometallic Ca/CaO/PO 4 was lower than the Korean standard regulatory limit for hazardous waste landfills. The morphology and elemental composition of the nanometallic Ca/CaO-treated ASR residue were characterized by field emission scanning election microscopy combined with electron dispersive spectroscopy (FE-SEM/EDS). The results indicated that the amounts of heavy metals detectable on the ASR thermal residue surface decreased and the Ca/PO 4 mass percent increased. X-ray diffraction (XRD) pattern analysis indicated that the main fraction of enclosed/bound materials on ASR residue included Ca/PO 4 − associated crystalline complexes, and that immobile Ca/PO 4 salts remarkably inhibited the desorption of heavy metals from ASR residues. These results support the potential use of nanometallic Ca/CaO/PO 4 as a simple, suitable and highly efficient material for the gentle

Evaluation of heavy metals in hazardous automobile shredder residue thermal residue and immobilization with novel nano-size calcium dispersed reagent

Energy Technology Data Exchange (ETDEWEB)

Lee, Chi-Hyeon; Truc, Nguyen Thi Thanh [Department of Civil and Environmental Engineering, University of Ulsan, Daehak-ro 93, Nam-gu, Ulsan 680-749 (Korea, Republic of); Lee, Byeong-Kyu, E-mail: bklee@ulsan.ac.kr [Department of Civil and Environmental Engineering, University of Ulsan, Daehak-ro 93, Nam-gu, Ulsan 680-749 (Korea, Republic of); Mitoma, Yoshiharu [Department of Environmental Sciences, Prefectural University of Hiroshima, 562 Nanatsuka-Cho Shobara City, Hiroshima 727-0023 (Japan); Mallampati, Srinivasa Reddy, E-mail: srireddys@ulsan.ac.kr [Department of Civil and Environmental Engineering, University of Ulsan, Daehak-ro 93, Nam-gu, Ulsan 680-749 (Korea, Republic of)

2015-10-15

Graphical abstract: Schematic representation of possible mechanisms determining the heavy metals immobilization efficiencyof ASR dust/thermal residues after treatment with nanometallic Ca/CaO/PO{sub 4}. - Highlights: • Nanometallic Ca/CaO/PO{sub 4} for heavy metals immobilization in ASR residue. • Heavy metals immobilization in dry condition attained about 95–100%. • Remaining heavy metals were lower than the Korean standard regulatory limit. • The amounts of heavy metals detectable on the ASR dust surface decreased. • Nanometallic Ca/CaO/PO{sub 4} has a promising potential for heavy metal remediation. - Abstract: This study was conducted to synthesize and apply a nano-size calcium dispersed reagent as an immobilization material for heavy metal-contaminated automobile shredder residues (ASR) dust/thermal residues in dry condition. Simple mixing with a nanometallic Ca/CaO/PO{sub 4} dispersion mixture immobilized 95–100% of heavy metals in ASR dust/thermal residues (including bottom ash, cavity ash, boiler and bag filter ash). The quantity of heavy metals leached from thermal residues after treatment by nanometallic Ca/CaO/PO{sub 4} was lower than the Korean standard regulatory limit for hazardous waste landfills. The morphology and elemental composition of the nanometallic Ca/CaO-treated ASR residue were characterized by field emission scanning election microscopy combined with electron dispersive spectroscopy (FE-SEM/EDS). The results indicated that the amounts of heavy metals detectable on the ASR thermal residue surface decreased and the Ca/PO{sub 4} mass percent increased. X-ray diffraction (XRD) pattern analysis indicated that the main fraction of enclosed/bound materials on ASR residue included Ca/PO{sub 4}− associated crystalline complexes, and that immobile Ca/PO{sub 4} salts remarkably inhibited the desorption of heavy metals from ASR residues. These results support the potential use of nanometallic Ca/CaO/PO{sub 4} as a simple, suitable and

Characterization of residues from waste combustion in fluidized bed boilers. Evaluation report

International Nuclear Information System (INIS)

Hagman, U.; Elander, P.

1996-04-01

In this report a thorough characterization of the solid residues from municipal solid waste combustion in a Kvaerner EnviroPower bubbling fluidized bed boiler in Lidkoeping, is presented. Three different end products are generated, namely bottom ash, cyclone ash, and filter ash. The bottom ash, consisting of bed ash and hopper ash, is screened and useful bed material recycled. In the characterization, also the primary constituents bed ash and hopper ash have been included. A chemical characterization have been performed including total inorganic contents, content of unburnt matter, leaching behaviour (availability tests, column tests, pH-static tests) and leaching tests according to certain standards for classification (AFX31-210, DIN38414, TCLP). Physical characterization have included grain size distribution, grain density, compaction properties and stabilization of cyclone ash with subsequent testing of comprehensive strength and saturated hydraulic conductivity. From an environmental point of view, the quality of the bottom ash and probably the cyclone ash from fluidized bed combustion as determined in this study, indicate a potential for utilization. Utilization of the bottom ash could be accepted in certain countries, e.g. France, according to their current limit values. In other countries, e.g. Sweden, no general limit values are given and utilization have to be applied for in each case. The judgement is then based, not only on total contents in the residue and its leaching behaviour, but also on the specific environmental conditions at the site. 7 refs, 17 figs, 12 tabs

Sieving of municipal solid waste incineration (MSWI) bottom ash; Siktning av askor fraan avfallsfoerbraenning

Energy Technology Data Exchange (ETDEWEB)

Todorovic, Jelena

2010-07-01

Waste-to-Energy is steadily increasing in Sweden and more than 46 % of municipal solid waste (MSW) is being incinerated. Solid residues from MSW incineration (MSWI) mainly constitute of bottom ash and air pollution control (APC) residues. Bottom ashes from MSWI amounted to 0.7 millions of tons and APC residues to 0.2 millions of tons in 2008. Bottom ashes from MSWI contain pollutants like metals (e.g. Pb, Zn, Cu), metalloids (e.g. As, Se), elements forming oxyanions (e.g. Sb, Cr, Mo) and easily soluble salts like chlorides and sulphates. These constituents can leach out polluting the environment if ash comes in contact with water. Treatment methods for decreasing the amount of pollutants in ashes or their mobility are therefore needed. Sieving was investigated as a separate or a complementary treatment method for MSWI ashes. Hypothesis was that the large share of pollutant concentrations could be removed from the ashes through separation of the finest fractions. The rest is less harmful to the environment, more acceptable as secondary construction material or less costly to landfill. Investigation included three MSWI ashes, namely bottom ash from Boraas Energy och Miljoe's plant with fluid bad, boiler ash from the same plant and bottom ash from Renova's stocker grate type plant. Ashes were sieved in 2-4 size fractions. Total content of pollutants and their leachability (batch leaching test, L/S=10 l/kg) was assessed for each of the fractions. Leaching results were compared to limit values stipulated by Swedish Environmental Protection Agency for acceptance of waste at landfills as wells as to recommendations for reuse of waste as a construction material. Results from bottom ash from the stocker grate type incinerator and from the boiler ash confirm the hypothesis that pollutants leach out in higher concentrations from the finer fractions. A large amount of pollutant could be removed from the ashes through sieving, but the goal to produce a fraction that

Electrodialytic remediation of air pollution control residues

DEFF Research Database (Denmark)

Jensen, Pernille Erland

Air pollution control (APC) residue from municipal solid waste incineration (MSWI) consists of the fly ash, and, in dry and semi-dry systems, also the reaction products from the flue gas cleaning process. APC residue is considered a hazardous waste due to its high alkalinity, high content of salt...

Organic substances in ashes; Organiska aemnen i askor

Energy Technology Data Exchange (ETDEWEB)

Bjurstroem, Henrik [AaF-Process AB, Stockholm (Sweden)

2006-12-15

Based on a review of available literature the following conclusions have been reached: Organic substances constitute a minor part of the TOC, Total Organic Carbon, and inert, elemental carbon constitutes the major part, TOC being expressed as weight percent of the ash. Organic substances are trace substances, with concentrations of the order a few mg/kg, exceptionally g/kg, in screening analyses, and of the order of ng/kg to mg/kg in dedicated analyses. The results from a screening of organic content depend largely on sample preparation and the method of analysis. The substances that are commonly identified are aliphatic acids and n-alkanes (semi-volatile substances). However, in one investigation chlorinated hydrocarbons such as trichloroethylene were found instead, which are more volatile than acids and n-alkanes In the leachates, organic substances are mostly humus-like relatively high molecular products of degradation. There is not any experimental evidence for substances to be terminated, which evidence would allow an assessment of their importance. The concentrations of dioxins and furans in all ashes seem to be low, from a few ng/kg TEQ ta few tens of ng/kg TEQ. Their concentration in bioashes is significantly lower than the default value in UNEP's guidelines for national inventories of sources of dioxins. The exception is air pollution control residues from waste incineration, which residues contain 200 - 2,000 ng/kg TEQ depending on the type of plant. If combustion residues from waste incineration are well investigated, residues from other fuels are not. The concentration of PAH varies more widely and is more uncertain, from 0.015 mg/kg DS ta few hundreds of mg/kg DS. It is not feasible tassess the consequences for the environment of the presence of organic substances in ashes in this survey. This demands a separate study.

Characterisation of agroindustrial solid residues as biofuels and potential application in thermochemical processes.

Science.gov (United States)

Virmond, Elaine; De Sena, Rennio F; Albrecht, Waldir; Althoff, Christine A; Moreira, Regina F P M; José, Humberto J

2012-10-01

In the present work, selected agroindustrial solid residues from Brazil - biosolids from meat processing wastewater treatment and mixture of sawdust with these biosolids; residues from apple and orange juice industries; sugarcane bagasse; açaí kernels (Euterpe oleracea) and rice husk - were characterised as solid fuels and an evaluation of their properties, including proximate and ultimate composition, energy content, thermal behaviour, composition and fusibility of the ashes was performed. The lower heating value of the biomasses ranged from 14.31 MJkg(-1) to 29.14 MJkg(-1), on a dry and ash free basis (daf), all presenting high volatile matter content, varying between 70.57 wt.% and 85.36 wt.% (daf) what improves the thermochemical conversion of the solids. The fouling and slagging tendency of the ashes was predicted based on the fuel ash composition and on the ash fusibility correlations proposed in the literature, which is important to the project and operation of biomass conversion systems. The potential for application of the Brazilian agroindustrial solid residues studied as alternative energy sources in thermochemical processes has been identified, especially concerning direct combustion for steam generation. Copyright © 2012 Elsevier Ltd. All rights reserved.

Solid residues from Italian municipal solid waste incinerators: A source for "critical" raw materials.

Science.gov (United States)

Funari, Valerio; Braga, Roberto; Bokhari, Syed Nadeem Hussain; Dinelli, Enrico; Meisel, Thomas

2015-11-01

The incineration of municipal solid wastes is an important part of the waste management system along with recycling and waste disposal, and the solid residues produced after the thermal process have received attention for environmental concerns and the recovery of valuable metals. This study focuses on the Critical Raw Materials (CRM) content in solid residues from two Italian municipal waste incinerator (MSWI) plants. We sampled untreated bottom ash and fly ash residues, i.e. the two main outputs of common grate-furnace incinerators, and determined their total elemental composition with sensitive analytical techniques such as XRF and ICP-MS. After the removal of a few coarse metallic objects from bottom ashes, the corresponding ICP solutions were obtained using strong digestion methods, to ensure the dissolution of the most refractory components that could host significant amounts of precious metals and CRM. The integration of accurate chemical data with a substance flow analysis, which takes into account the mass balance and uncertainties assessment, indicates that bottom and fly ashes can be considered as a low concentration stream of precious and high-tech metals. The magnesium, copper, antimony and zinc contents are close to the corresponding values of a low-grade ore. The distribution of the elements flow between bottom and fly ash, and within different grain size fractions of bottom ash, is appraised. Most elements are enriched in the bottom ash flow, especially in the fine grained fractions. However, the calculated transfer coefficients indicate that Sb and Zn strongly partition into the fly ashes. The comparison with available studies indicates that the CRM concentrations in the untreated solid residues are comparable with those residues that undergo post-treatment beneficiations, e.g. separation between ferrous and non-ferrous fractions. The suggested separate collection of "fresh" bottom ash, which could be processed for further mineral upgrading, can

Life cycle assessment of disposal of residues from municipal solid waste incineration: recycling of bottom ash in road construction or landfilling in Denmark evaluated in the ROAD-RES model.

Science.gov (United States)

Birgisdóttir, H; Bhander, G; Hauschild, M Z; Christensen, T H

2007-01-01

Two disposal methods for MSWI bottom ash were assessed in a new life cycle assessment (LCA) model for road construction and disposal of residues. The two scenarios evaluated in the model were: (i) landfilling of bottom ash in a coastal landfill in Denmark and (ii) recycling of bottom ash as subbase layer in an asphalted secondary road. The LCA included resource and energy consumption, and emissions associated with upgrading of bottom ash, transport, landfilling processes, incorporation of bottom ash in road, substitution of natural gravel as road construction material and leaching of heavy metals and salts from bottom ash in road as well as in landfill. Environmental impacts associated with emissions to air, fresh surface water, marine surface water, groundwater and soil were aggregated into 12 environmental impact categories: Global Warming, Photochemical Ozone Formation, Nutrient Enrichment, Acidification, Stratospheric Ozone Depletion, Human Toxicity via air/water/soil, Ecotoxicity in water/soil, and a new impact category, Stored Ecotoxicity to water/soil that accounts for the presence of heavy metals and very persistent organic compounds that in the long-term might leach. Leaching of heavy metals and salts from bottom ash was estimated from a series of laboratory leaching tests. For both scenarios, Ecotoxicity(water) was, when evaluated for the first 100 yr, the most important among the twelve impact categories involved in the assessment. Human Toxicity(soil) was also important, especially for the Road scenario. When the long-term leaching of heavy metals from bottom ash was evaluated, based on the total content of heavy metals in bottom ash, all impact categories became negligible compared to the potential Stored Ecotoxicity, which was two orders of magnitudes greater than Ecotoxicity(water). Copper was the constituent that gave the strongest contributions to the ecotoxicities. The most important resources consumed were clay as liner in landfill and the

Characterization of coal fly ash components by laser-induced breakdown spectroscopy

International Nuclear Information System (INIS)

Ctvrtnickova, Tereza; Mateo, Mari-Paz; Yanez, Armando; Nicolas, Gines

2009-01-01

The high sensitivity of laser-induced breakdown spectroscopy (LIBS) for the detection of most of the fly ash components enables the analysis of these residues produced during the combustion of coal. Fly ash consists of oxides (SiO 2 , Al 2 O 3 , Fe 2 O 3 , CaO...) and unburnt carbon which is the major determinant of combustion efficiency in coal fired boilers. For example, an excessive amount of residual carbon dispersed in the fly ash means a significant loss of energy (Styszko et al., 2004). Standard methods employed for the analysis of fly ash make not possible a control of boiler in real time. LIBS technique can significantly reduce the time of analysis, in some cases even an online detection can be performed. For this reason, some studies have been addressed in order to demonstrate the capability of the laser-induced breakdown spectroscopy technique for the detection of carbon content in high pressure conditions typical of thermal power plants (Noda et al., 2002) and for the monitoring of unburnt carbon for the boiler control in real time (Kurihara et al., 2003). In particular, the content of unburnt carbon is a valuable indicator for the control of fly ash quality and for the boiler combustion. Depending on this unburnt carbon content, fly ash can be disposed as an industrial waste or as a raw material for the production of concrete in the construction sector. In this study, analyses were performed on specimens of various forms of preparation. Pressed pellets were prepared with two different binders. Presented results concern the nature and amount of the binder used to pelletize the powder, and the laser-induced breakdown spectroscopy parameters and procedure required to draw calibration curves of elements from the fly ash. Analysis 'on tape' was performed in order to establish the experimental conditions for the future 'online analysis'.

Flow analysis of heavy metals in a pilot-scale incinerator for residues from waste electrical and electronic equipment dismantling

International Nuclear Information System (INIS)

Long, Yu-Yang; Feng, Yi-Jian; Cai, Si-Shi; Ding, Wei-Xu; Shen, Dong-Sheng

2013-01-01

Highlights: • Cu, Zn, Pb, and Ni are enriched in bottom ash from WEEE dismantling residues. • The heavy metal residual fraction restricts transfer in the incinerator. • Pre-treatment to remove heavy metals from WEEE residues would reduce emissions. -- Abstract: The large amount of residues generated from dismantling waste electrical and electronic equipment (WEEE) results in a considerable environmental burden. We used material flow analysis to investigate heavy metal behavior in an incineration plant in China used exclusively to incinerate residues from WEEE dismantling. The heavy metals tested were enriched in the bottom and fly ashes after incineration. However, the contents of heavy metals in the bottom ash, fly ash and exhaust gas do not have a significant correlation with that of the input waste. The evaporation and recondensation behavior of heavy metals caused their contents to differ with air pollution control equipment because of the temperature difference during gas venting. Among the heavy metals tested, Cd had the strongest tendency to transfer during incineration (T Cd = 69.5%) because it had the lowest melting point, followed by Cu, Ni, Pb and Zn. The exchangeable and residual fractions of heavy metals increased substantially in the incineration products compared with that of the input residues. Although the mass of residues from WEEE dismantling can be reduced by 70% by incineration, the safe disposal of the metal-enriched bottom and fly ashes is still required

Flow analysis of heavy metals in a pilot-scale incinerator for residues from waste electrical and electronic equipment dismantling

Energy Technology Data Exchange (ETDEWEB)

Long, Yu-Yang; Feng, Yi-Jian; Cai, Si-Shi; Ding, Wei-Xu; Shen, Dong-Sheng, E-mail: shends@zju.edu.cn

2013-10-15

Highlights: • Cu, Zn, Pb, and Ni are enriched in bottom ash from WEEE dismantling residues. • The heavy metal residual fraction restricts transfer in the incinerator. • Pre-treatment to remove heavy metals from WEEE residues would reduce emissions. -- Abstract: The large amount of residues generated from dismantling waste electrical and electronic equipment (WEEE) results in a considerable environmental burden. We used material flow analysis to investigate heavy metal behavior in an incineration plant in China used exclusively to incinerate residues from WEEE dismantling. The heavy metals tested were enriched in the bottom and fly ashes after incineration. However, the contents of heavy metals in the bottom ash, fly ash and exhaust gas do not have a significant correlation with that of the input waste. The evaporation and recondensation behavior of heavy metals caused their contents to differ with air pollution control equipment because of the temperature difference during gas venting. Among the heavy metals tested, Cd had the strongest tendency to transfer during incineration (T{sub Cd} = 69.5%) because it had the lowest melting point, followed by Cu, Ni, Pb and Zn. The exchangeable and residual fractions of heavy metals increased substantially in the incineration products compared with that of the input residues. Although the mass of residues from WEEE dismantling can be reduced by 70% by incineration, the safe disposal of the metal-enriched bottom and fly ashes is still required.

Electrolytic recuperation of heavy metals and chlorine from fly-ashes and washwater of a household incinerator

Energy Technology Data Exchange (ETDEWEB)

Maes, H.; Carpels, M.; Elslander, H.; Van Houtven, D.; Vereecken, J.; Kinnaer, L.; Hermans, N.; Gielen, C.; Van Kerckhoven, M.; Raats, L. [Vlaamse Instelling voor Technologisch Onderzoek (VITO), Mol (Belgium)

1995-12-31

The treatment and processing of the residues which result from the household incineration process were investigated in a study conducted in Belgium. Incineration produces large amounts of solid residue, particularly fly-ash, which contains a large degree of heavy metals. Also, the large amount of acid washwater flow which comes from the gas washer is highly concentrated with chlorine, and heavy metals. Presently, both the fly-ash and the wastewater are dumped at disposal sites. Two objectives for waste management were presented. The first was to improve the fly-ash for potential use as, for example, filler in road surfaces. The second was to reduce the wastewater flow and to use neutralizing reagents or an electro-chemical treatment on the washwater, in order to recuperate the chlorine. The fly-ash was treated by leaching with the acid washwater. The leached heavy metals were recuperated by electrolysis. It was concluded, however, that electrolytic recuperation of heavy metals from fly ash was not economically feasible. 2 refs., 7 tabs., 8 figs.

Characteristics estimation of coal liquefaction residue; Sekitan ekika zansa seijo no suisan ni kansuru kento

Energy Technology Data Exchange (ETDEWEB)

Itonaga, M.; Imada, K. [Nippon Steel Corp., Tokyo (Japan); Okada, Y.; Inokuchi, K. [Mitsui SRC Development Co. Ltd., Tokyo (Japan)

1996-10-28

The paper studied a possibility of estimating characteristics of coal liquefaction residue from liquefaction conditions in the case of fixing coal kind in the NEDOL process coal liquefaction PSU. Wyoming coal was used for the study, and the already proposed simplified liquefaction reaction models were used. Among material balances explained by the models, those of asphaltene, preasphaltene, THF insoluble matters are concerned with residue composition. Ash content is separately calculated from ash balance. Reaction velocity constants of simplified liquefaction reaction models which influence the residue composition were obtained by the multiple regression method from experimental results in the past. The estimation expression of residue viscosity was introduced from residue ash/composition. When the residue composition is estimated by the model from liquefaction conditions, and the residue viscosity is obtained using it, the higher the liquefaction temperature is, the higher the residue viscosity is. The result obtained well agreed the measuring result. The simplified liquefaction model of a certain coal kind has been established, and characteristics of residue can be estimated even at liquefaction conditions which have never been experienced before if there is a certain amount of the accumulated data on residue composition/characteristics. 4 refs., 4 figs., 4 tabs.

Beneficial Use and Recycling of Municipal Waste Combustion Residues - A Comprehensive Resource Document

Energy Technology Data Exchange (ETDEWEB)

Wiles, C.; Shepherd, P.

1999-04-26

This document summarizes information from worldwide sources on the beneficial use of residues from the combustion of municipal. The information presented, including results of numerous research projects, field demonstrations, and actual full-scale projects, demonstrates that the ash can be safely used. It includes data on ash characteristics, environmental considerations, guidance on selected ash use applications, and information on federal and state regulations and policies affecting ash use.

Some problems of oil shale retorting in Estonia

International Nuclear Information System (INIS)

Oepik, I.

1994-01-01

Oil shale in Estonia will be competitive in the long term as a primary resource for power generating. The price of energy of Estonian oil shale is at present approximately 4 times lower than of coal. The price of electricity is anticipated to grow up to EEK 1.0/kWh in year 2020. The electricity price EEK 0.2/kWh at present in Estonia does not include capital costs needed for refurbishing of Estonian oil-shale-consuming power stations between the years 2000-2010. While all the prices and calculations of the enterprise are presented with no inflation adjustment, the other operation costs of oil shale retorting are anticipated for the prognosed period to remain at the present level: power consumption kWh 280/t crude oils and other operation costs (excluding labour, raw material and power consumption) EEK 100/t of oil

Quantification of heavy metals from residual waste and ashes from the treatment plant of residual water Reciclagua and,effects for the health of those workers which manipulate those residuals

International Nuclear Information System (INIS)

Guerrero D, J.J.

2004-01-01

In this work, the technique of leaching using thermostatted column in series is applied, the X-ray diffraction for the identification of the atomic and molecular structure of the toxic metals that are present in the residual muds of the water treatment plant located in the municipality of Lerma Estado de Mexico, named RECICLAGUA, likewise the technique is used of emission spectrometry for plasma and X-ray fluorescence for the qualitative analysis. Its were take samples of residual mud and of incinerated mud of the treatment plant of residual waters of the industrial corridor Toluca -Lerma RECICLAGUA, located in Lerma Estado de Mexico. For this study there were mixed 100 g of residual mud with a solution to 10% of mineral acid or sodium hydroxide according to the case, to adjust the one pH at 2, 5, 7 and 10, it was added bisulfite, of 0.3-1.5 g of dodecyl sulfate sodium and 3.939 of DTPA (triple V) (Diethylene triamine pentaacetate). To this mud and ashes were extracted the toxic and valuable metals by means of the leaching technique using thermostatted columns placed in series that were designed by the Dr. Jaime Vite Torres; it is necessary to make mention that so much the process as the equipment with those that work it was patented by the same one. With the extraction of these metals benefits are obtained, mainly of economic type, achieving the decrease of the volume of those wastes that have been generated; as well as the so much the use of those residuals, once the metals have been eliminated, as of those liquors where the metals were extracted. It was carried out a quantitative analysis using emission spectrometry by plasma in solids by this way to be able to know the content of the present metals in the sample before and later of leaching them, these results reported a great quantity of elements. Another of the techniques employees was the X-ray diffraction analysis that provides an elementary content of the samples, identifying elements that are present in

Coal ash fusion temperatures - new characterization techniques and implications for slagging and fouling

Energy Technology Data Exchange (ETDEWEB)

Wall, T.F.; Creelman, R.A.; Gupta, R.P.; Gupta, S.K.; Coin, C.; Lowe, A. [University of Newcastle, Newcastle, NSW (Australia). CRC for Black Coal Utilisation

1998-09-01

The ash fusion test (AFT) is the accepted test for the propensity of coal ash to slag in the furnace. The well-documented shortcomings of this technique for estimating the fusion temperature of coal ash are its subjective nature and poor accuracy. Alternative measurements based on the shrinkage and electrical conductivity of heating samples are therefore examined here with laboratory ash prepared at about 800{degree}C in crucibles, as well as combustion ash samples from power stations. Sensitive shrinkage measurements indicate temperatures of rapid change which correspond to the formation of liquid phases that can be identified on ternary phase diagrams. The existence and extent of formation of these phases, as quantified by the magnitude of `peaks` in the test, provide alternative ash fusion temperatures. The peaks from laboratory ashes and corresponding combustion ashes derived from the same coals show clear differences which may be related to the evaporation of potassium during combustion and the reactions of the mineral residues to form combustion ash. A preliminary evaluation of data from nine power stations indicates that shrinkage measurements can provide an alternative approach to characterizing slagging. 15 refs., 9 figs., 2 tabs.

APC fly ashes stabilized with Portland cement for further development of road sub-base aggregates

Science.gov (United States)

Formosa, J.; Giro-Paloma, J.; Maldonado-Alameda, A.; Huete-Hernández, S.; Chimenos, J. M.

2017-10-01

Although waste-to-energy plants allow reducing the mass and volume of municipal solid waste (MSW) incinerated, an average around 30 % of the total content remains as bottom ash (BA) and air pollution control (APC) ashes at the end of combustion process. While weathered bottom ash (WBA) is considered a non-hazardous residue that can be revalorized as a secondary aggregate, APC fly ashes generated during the flue gas treatment are classified as hazardous waste and are handled in landfill disposal after stabilization, usually with Portland cement (OPC). However, taking into account the amount of APC residues produced and the disposing cost in landfill, their revalorization is an important issue that could be effectively addressed. As MSW can be incinerated producing bottom ashes (BA) or air pollutant control (APC) residues, the development of a mortar formulated with APC fly ash as secondary building material is a significant risk to the environment for their content of heavy metals. In this way, Design of Experiment (DoE) was used for the improvement of granular material (GM) formulation composed by APC and OPC for further uses as road sub-base aggregate. DoE analysis was successful in the modelling and optimization the formulation as function of the mechanical properties and APC amount. Consequently, an optimal mortar formulation (OMF) of around 50 wt.% APC and 50 wt.% OPC was considered. The OMF leachates and abrasion resistance have been analyzed. These results have demonstrated the viability of OMF as non-hazardous material feasible to be used as secondary aggregate. Moreover, it would be possible to consider the environmental assessment of a GM composed by ≈20 wt.% of OMF and ≈80 wt.% of WBA in order to improve mechanical properties and heavy metals stabilization.

Characteristics of biomass ashes from different materials and their ameliorative effects on acid soils.

Science.gov (United States)

Shi, Renyong; Li, Jiuyu; Jiang, Jun; Mehmood, Khalid; Liu, Yuan; Xu, Renkou; Qian, Wei

2017-05-01

The chemical characteristics, element contents, mineral compositions, and the ameliorative effects on acid soils of five biomass ashes from different materials were analyzed. The chemical properties of the ashes varied depending on the source biomass material. An increase in the concrete shuttering contents in the biomass materials led to higher alkalinity, and higher Ca and Mg levels in biomass ashes, which made them particularly good at ameliorating effects on soil acidity. However, heavy metal contents, such as Cr, Cu, and Zn in the ashes, were relatively high. The incorporation of all ashes increased soil pH, exchangeable base cations, and available phosphorus, but decreased soil exchangeable acidity. The application of the ashes from biomass materials with a high concrete shuttering content increased the soil available heavy metal contents. Therefore, the biomass ashes from wood and crop residues with low concrete contents were the better acid soil amendments. Copyright © 2016. Published by Elsevier B.V.

Assessment of the PCDD/F fate from MSWI residue used in road construction in France.

Science.gov (United States)

Badreddine, R; François, D

2009-01-01

MSWI fly ash is susceptible to contain high amount of polychlorinated dibenzo-dioxins and polychlorinated dibenzo-furans. However, the use of MSWI residue for road construction started in France at a period when MSWI Bottom Ash and MSWI fly ash were not separated. From four old road sites, MSWI residue, road soils, reference soils and geo-textiles were sampled and their PCDD/F contents were analyzed. MSWI residue show a great heterogeneity but also high amounts of PCDD/F (14-2960 ng I-TEQ kg(-1)dm). Soils underlying the road show less heterogeneity and PCDD/F contents between 0.57 and 7.23 ng I-TEQ kg(-1)dm, lower than ordinary soils. Moreover, the specific analysis of the 17 toxic PCDD/F congeners (notably the 2,3,7,8-TetraCDD) indicates the very low harmfulness of road soils. The study also allows to assert the relation between the MSWI residue particle size and the PCDD/F content.

Chloride leaching from municipal solid waste incineration (MSWI) bottom ash

NARCIS (Netherlands)

Alam, Q.; Schollbach, K.; Florea, M.V.A.; Brouwers, H.J.H.; Vlastimil, Bilek; Kersner, Zbynek; Simonova, Hana

2017-01-01

The presence of chlorides in the Municipal Solid Waste Incineration bottom ashes (BA) hinders their potential for recycling in building materials. The contaminant content in the incineration residues is strictly regulated by the Dutch legislation Soil Quality Decree (2013). The fine fraction

Recycling of MSWI fly ash in clay bricks-effect of washing and electrodialytic treatment

DEFF Research Database (Denmark)

Chen, Wan; Klupsch, Ewa; Kirkelund, Gunvor Marie

2017-01-01

Fly ash generated from municipal solid waste incineration (MSWI) is a hazardous waste due to presence and leachability of heavy metals and organic pollutants (e.g. dioxins and polycyclic aromatic hydrocarbons). In 2000, approximately 25 Mt/year of fly ash was generated in USA, Japan and EU...... (Reijnders 2005). Electrodialytic remediation (EDR) is one technique for MSWI fly ash treatment (Ferreira et al. 2005), where an electric DC field is applied to an ash-water suspension to extract and separate heavy metal by migration towards anode or cathode through ion exchange membranes. Ferreira et al....... (2008) observed that in MSWI ash treated by water washing and EDR, metals were mainly in the strongly bonded and residual phases, indicating a reduction in the ash’s environmental risk. Belmonte et al. (2016) made Greenlandic bricks (∼2 g discs) containing 20% and 40% of EDR treated MSWI fly ash...

Evaluation of resource recovery from waste incineration residues--the case of zinc.

Science.gov (United States)

Fellner, J; Lederer, J; Purgar, A; Winterstetter, A; Rechberger, H; Winter, F; Laner, D

2015-03-01

Solid residues generated at European Waste to Energy plants contain altogether about 69,000 t/a of Zn, of which more than 50% accumulates in air pollution control residues, mainly boiler and filter ashes. Intensive research activities aiming at Zn recovery from such residues recently resulted in a technical scale Zn recovery plant at a Swiss waste incinerator. By acidic leaching and subsequent electrolysis this technology (FLUREC) allows generating metallic Zn of purity>99.9%. In the present paper the economic viability of the FLUREC technology with respect to Zn recovery from different solid residues of waste incineration has been investigated and subsequently been categorised according to the mineral resource classification scheme of McKelvey. The results of the analysis demonstrate that recovery costs for Zn are highly dependent on the costs for current fly ash disposal (e.g. cost for subsurface landfilling). Assuming current disposal practice costs of 220€/ton fly ash, resulting recovery costs for Zn are generally higher than its current market price of 1.6€/kg Zn. With respect to the resource classification this outcome indicates that none of the identified Zn resources present in incineration residues can be economically extracted and thus cannot be classified as a reserve. Only for about 4800 t/a of Zn an extraction would be marginally economic, meaning that recovery costs are only slightly (less than 20%) higher than the current market price for Zn. For the remaining Zn resources production costs are between 1.5 and 4 times (7900 t/a Zn) and 10-80 times (55,300 t/a Zn) higher than the current market value. The economic potential for Zn recovery from waste incineration residues is highest for filter ashes generated at grate incinerators equipped with wet air pollution control. Copyright © 2014 Elsevier Ltd. All rights reserved.

Chemical durability of glass and glass-ceramic materials, developed in laboratory scale, from industrial oil shale residue. Preliminary results

International Nuclear Information System (INIS)

Araujo Fonseca, M.V. de; Souza Santos, P. de

1990-01-01

Industrial developments frequently drive to the natural resources extinction. The recycling era has come out a long time ago and it has been evident that great part of industrial work's problems are related to the pollution and the raw materials extinction. These problems should be solved, with advantages, through industrial residues recycling. This study deals with glass and glass-ceramics materials obtained from oil shale (Irati Formation-Sao Mateus do Sul-Parana State) industrialization residues. The reached results show that a controled devitrification of retorted oil shale glass improves its performance related to chemical attack. The crystallinity caracterization of the oil shales glass-ceramic was made through X-ray diffraction. (author) [pt

Geochemistry of ultra-fine and nano-compounds in coal gasification ashes: A synoptic view

Energy Technology Data Exchange (ETDEWEB)

Kronbauer, Marcio A. [Centro Universitário La Salle, Mestrado em Avaliação de Impactos Ambientais em Mineração, Victor Barreto, 2288 Centro, 92010-000 Canoas, RS (Brazil); Universidade Federal do Rio Grande do Sul, Escola de Engenharia, Departamento de Metalurgia, Centro de Tecnologia, Av. Bento Gonçalves, 9500, Bairro Agronomia, CEP: 91501-970, Porto Alegre, RS (Brazil); Izquierdo, Maria [School of Applied Sciences, Cranfield University, Bedfordshire MK43 0AL (United Kingdom); Dai, Shifeng [State Key Laboratory of Coal Resources and Safe Mining, China University of Mining and Technology, Beijing 100083 (China); Waanders, Frans B. [School of Chemical and Minerals Engineering, North West University (Potchefstroom campus), Potchefstroom 2531 (South Africa); Wagner, Nicola J. [School of Chemical and Metallurgical Engineering, University of the Witwatersrand, Johannesburg (South Africa); Mastalerz, Maria [Indiana Geological Survey, Indiana University, Bloomington, IN 47405-2208 (United States); Hower, James C. [University of Kentucky Center for Applied Energy Research, 2540 Research Park Drive, Lexington, KY 40511 (United States); Oliveira, Marcos L.S. [Environmental Science and Nanotechnology Department, Catarinense Institute of Environmental Research and Human Development, IPADHC, Capivari de Baixo, Santa Catarina (Brazil); Taffarel, Silvio R.; Bizani, Delmar [Centro Universitário La Salle, Mestrado em Avaliação de Impactos Ambientais em Mineração, Victor Barreto, 2288 Centro, 92010-000 Canoas, RS (Brazil); and others

2013-07-01

The nano-mineralogy, petrology, and chemistry of coal gasification products have not been studied as extensively as the products of the more widely used pulverized-coal combustion. The solid residues from the gasification of a low- to medium-sulfur, inertinite-rich, volatile A bituminous coal, and a high sulfur, vitrinite-rich, volatile C bituminous coal were investigated. Multifaceted chemical characterization by XRD, Raman spectroscopy, petrology, FE-SEM/EDS, and HR-TEM/SEAD/FFT/EDS provided an in-depth understanding of coal gasification ash-forming processes. The petrology of the residues generally reflected the rank and maceral composition of the feed coals, with the higher rank, high-inertinite coal having anisotropic carbons and inertinite in the residue, and the lower rank coal-derived residue containing isotropic carbons. The feed coal chemistry determines the mineralogy of the non-glass, non-carbon portions of the residues, with the proportions of CaCO{sub 3} versus Al{sub 2}O{sub 3} determining the tendency towards the neoformation of anorthite versus mullite, respectively. Electron beam studies showed the presence of a number of potentially hazardous elements in nanoparticles. Some of the neoformed ultra-fine/nano-minerals found in the coal ashes are the same as those commonly associated with oxidation/transformation of sulfides and sulfates. - Highlights: • Coal waste geochemisty can provide increased environmental information in coal-mining areas. • Oxidation is the major process for mineral transformation in coal ashes. • The electron bean methodology has been applied to investigate neoformed minerals.

Large-scale ash recycling in Central Sweden; Storskalig askhantering i mellansverige

Energy Technology Data Exchange (ETDEWEB)

Hansson, Mats [Stora Skog (Sweden)

1998-08-01

When logging residues (tops, branches) are withdrawn from the forest, most of the nutrient content of the trees is also lost. Some of the nutrient content of the soil is restored by weathering, but not all. When biomass is burnt as fuel most of the nutrients will be found in the ash. By recycling wood ash, in similar amounts as was withdrawn with the biomass, it is possible to compensate for the nutrient losses. This project was initiated to study how a rational recycling of wood ash could be performed under conditions valid for Stora, a large forest company in the middle of Sweden. A second aim was to give guiding principles for Stora`s own ash recycling while awaiting instructions from the authorities. In the project both theoretical studies and practical field studies were carried out. Studied areas are production of a stabilised ash product and different systems for transport and spreading of the ash product. The costs and results of spreading have also been monitored. The project showed that spreading of the ash can normally only take place when there is no snow. If production or transport is carried out during another time of the year, the ash has to be stored, either at the industry, in an intermediate storage, or in the forest. One important conclusion from the test period was that the result of the spreading depends heavily on the quality of the ash. Some of the ashes hardened in the spreading equipment, causing a complete stop of the spreading. It also caused problems if the ash was too wet. Plate-spreaders led to unequal quality of spreading, where some areas got more ash and some got less. Granulated ash was most easy to spread. Recommended system for spreading ash is: granulated ash transported unpacked in separate transports with lorries with exchangeable platforms. A large fores tractor spreads the ash in clearings, in the summer. The project has shown that large-scale ash recycling is possible to realize 22 figs, 5 tabs, 13 appendices

Studies of lagoon ash from Sarawak to assess the impact on the environment

Energy Technology Data Exchange (ETDEWEB)

Prabir Kumar Kolay; Harwant Singh [University Malaysia Sarawak, Sarawak (Malaysia). Dept. of Civil Engineering

2010-02-15

Coal utilization, mainly in thermal power plants, has increased significantly from 4.2 to 13 million tonnes within 2000 to 2005, which resulted in the production of approximately 2 million tonnes of coal ash in Malaysia. Of this only a small percentage is used as a cement ingredient, in concrete industry, as a fill material, etc. and with the rest of the amount being disposed in ash ponds or lagoons. If the lagoons are not properly designed with a landfill liner or if there is spillage from the ash pond, the toxic heavy metal present in coal ash can result in the contamination of the subsurface soil and the ground water. The concentration of heavy metals or trace elements in coal residues depends on the composition of a particular parent coal and the bulk utilization of lagoon ash for various purposes requires a complete characterization of the ash. Hence, this paper analyzes the coal ash for its trace element content and characterizes mainly physical, chemical, mineralogical, morphological and thermal properties of the lagoon ash from a local coal based thermal power plant from Sarawak, Malaysia. The results also indicated that, the concentration of some trace elements is quite high from the environmental perspective in this particular lagoon ash. 43 refs., 4 figs., 4 tabs.

Testing the possibility for reusing mswi bottom ash in Greenlandic road construction

DEFF Research Database (Denmark)

Kirkelund, Gunvor Marie; Jørgensen, Anders Stuhr; Villumsen, Arne

2012-01-01

requirements (a grain size distribution, wear resistance, visual fraction analysis and bearing capacity) for reuse as fill material in road construction [2]. Environmental classification based on heavy metal content and leachability was also investigated. The tests showed that it will not be possible to use......, which can influence the quality of MWSI residues. About 15,000 tons MSWI bottom ash is produced annually in Greenland and is disposed of at the open disposal sites without leachate collection or encapsulation. The MSWI bottom ash could have value as a secondary resource in construction work in Greenland...... the bottom ash directly after the incineration as the bottom ash did not comply with all the requirements specified by the Danish Road Directorate. These technical requirements could be improved by removing large fractions (> 45mm) and metal parts as well as changing the grain size distribution...

Thermal treatment and vitrification of boiler ash from a municipal solid waste incinerator.

Science.gov (United States)

Yang, Y; Xiao, Y; Voncken, J H L; Wilson, N

2008-06-15

Boiler ash generated from municipal solid waste (MSW) incinerators is usually classified as hazardous materials and requires special disposal. In the present study, the boiler ash was characterized for the chemical compositions, morphology and microstructure. The thermal chemical behavior during ash heating was investigated with thermal balance. Vitrification of the ash was conducted at a temperature of 1400 degrees C in order to generate a stable silicate slag, and the formed slag was examined with chemical and mineralogical analyses. The effect of vitrification on the leaching characteristics of various elements in the ash was evaluated with acid leaching. The study shows that the boiler ash as a heterogeneous fine powder contains mainly silicate, carbonate, sulfates, chlorides, and residues of organic materials and heavy metal compounds. At elevated temperatures, the boiler ash goes through the initial moisture removal, volatilization, decomposition, sintering, melting, and slag formation. At 1400 degrees C a thin layer of salt melt and a homogeneous glassy slag was formed. The experimental results indicate that leaching values of the vitrified slag are significantly reduced compared to the original boiler ash, and the vitrification could be an interesting alternative for a safer disposal of the boiler ash. Ash compacting, e.g., pelletizing can reduce volatilization and weight loss by about 50%, and would be a good option for the feed preparation before vitrification.

Characterization, treatment and utilization of rice husk ash in production processes of the industrial branch

International Nuclear Information System (INIS)

Stracke, Marcelo Paulo; Schmidt, Julia Isabel; Steffen, Ana Cristina; Sokolovicz, Boris; Kieckow, Flavio

2016-01-01

The rice husk ash (CCA) is a black powder rich in silica (contents above 90%) with many industrial applications. The ash was obtained from a rice processing industry in the state of Rio Grande do Sul. In this work the purpose is to characterize the rice husk ash and eliminate the residual carbon by methods such as acid leaching. The white ash is obtained by a chemical process followed by heating between 600 and 800 °C. The results were analyzed in DR-X, TGA and DSC. The DR-X analysis showed that the samples present high levels of silica in the crystalline form of quartz, cristobalite and tridymite. The white ash was obtained with high purity and presented a good result in the manufacture of paints. (author)

Addition of residues and reintroduction of microorganisms in Jatropha curcas cultivated in degraded soil

Directory of Open Access Journals (Sweden)

Adriana A. Santos

2016-04-01

Full Text Available ABSTRACT The aim of this study was to evaluate, through mycorrhization (root colonization and number of spores of arbuscular mycorrhizal fungi - AMF, leaf acid phosphatase and soil chemical characteristics, the effects of the addition of residues (macrophytes and ash, hydrogel and the reintroduction of microorganisms in a degraded area cultivated with jatropha. Degradation occurred when the surface soil was removed during the construction of a hydroelectric power plant. The experiment was set in a randomized block design, using a 2 x 2 x 4 factorial scheme, i.e., two inoculation treatments (with and without soil-inoculum, two hydrogel treatments (with and without and four with the addition of residues (macrophytes - MAC, ash, MAC + ash and control, without residues applied in the planting hole, with 4 replicates and 5 plants in each replicate. Soil from preserved Cerrado area was used as a source of microorganisms, including AMF. The conclusion is that, after 12 months of planting, the hydrogel increased root colonization, while the chemical characteristics of the degraded soil responded positively to the addition of MAC and MAC + ash, with increase in pH and SB and reduction of Al and H + Al. The addition of the soil-inoculum, along with MAC and MAC + ash, promoted higher mycorrhizal colonization and number of spores and reduced amounts of leaf acid phosphatase, indicating increased absorption of P by the host.

Reducing Heavy Metal Element from Coal Bottom Ash by Using Citric Acid Leaching Treatment

Directory of Open Access Journals (Sweden)

Yahya Ahmad Asyari

2017-01-01

Full Text Available Coal ash is the residue that is produced during coal combustion for instance fly ash, bottom ash or boiler slag which was primarily produced from the combustion of coal. With growth in coal burning power station, huge amount of coal bottom ash (CBA considered as hazardous material which are normally disposed in an on-site disposal system without any commercialization purpose. Previous researchers have studied the extraction of silica from agricultural wastes such as palm ash and rice husk ash (RHA and CBA by using leaching treatment method. In this study, the weaker acid, citric acid solution was used to replace the strong acid in leaching treatment process. Result showed that the heavy metal content such as Copper (Cu, Zinc (Zn and Lead (Pb can be decrease. Meanwhile the silica can be extracted up to 44% from coal bottom ash using citric acid leaching treatment under the optimum reaction time of 60 minutes with solution temperature of 60°C and concentration of citric acid more than 2%.

Elemental analysis of ash residue from combustion of CCA treated wood waste before and after electrodialytic extraction

DEFF Research Database (Denmark)

Pedersen, Anne Juul; Ottosen, Lisbeth M.

2006-01-01

Element distribution in a combined fly ash and bottom ash from combustion of copper chromate arsenate (CCA) treated wood waste was investigated by scanning electron microscopy (SEM/EDX) before and after electrodialytic extraction. The untreated ash contained various particles, including pieces...... of incompletely combusted wood rich in Cr and Ca, and irregular particles rich in Si, Al and K. Cr was also found incorporated in silica-based matrix particles. As was associated with Ca in porous (char) particles, indicating that Ca-arsenates had been formed during combustion. Cu was associated with Cr...... in the incompletely combusted wood pieces and was also found in almost pure form in a surface layer of some matrix particles – indicating surface condensation of volatile Cu species. In treated ash, Ca and As were no longer found together, indicating that Ca-arsenates had been dissolved due to the electrodialytic...

Residual oil fly ash induces cytotoxicity and mucin secretion by guinea pig tracheal epithelial cells via an oxidant-mediated mechanism.

Science.gov (United States)

Jiang, N; Dreher, K L; Dye, J A; Li, Y; Richards, J H; Martin, L D; Adler, K B

2000-03-15

Inhalation of ambient air particulate matter (PM) is associated with pulmonary injury and inflammation. Using primary cultures of guinea pig tracheal epithelial (GPTE) cells as an in vitro model of airway epithelium, we examined effects of exposure to suspensions of six different emission and ambient air PM samples: residual oil fly ash (ROFA) from an electrical power plant; fly ash from a domestic oil burning furnace (DOFA); ambient air dust from St. Louis (STL), Ottawa (OT), and Washington, DC (WDC); and volcanic ash from the eruption of Mount Saint Helens (MSH) in 1980. Effects of these particulates on cell viability (assessed via LDH assay), secretion of mucin (measured by a monoclonal antibody-based ELISA), and steady-state mRNA levels of the mucin gene MUC2 were determined. ROFA was the most toxic of the dusts tested, as it significantly increased LDH release following a 24-h incubation with 50 microg/cm(2) ROFA. ROFA also enhanced MUC2 mRNA after 4-h exposure, and mucin secretion after 8 h. ROFA-induced mucin secretion and cytotoxicity were attenuated by the oxidant scavenger, dimethylthiourea (DMTU). ROFA exposure also depleted cells of glutathione (GSH). Relatedly, depletion of intracellular GSH by treatment of the cells with buthionine sulfoxamine (BSO) also provoked mucin secretion, as well as enhancing the secretory effect of ROFA when the two agents were added together. L-NMA, the nitric oxide synthase (NOS) inhibitor, did not affect ROFA-induced mucin secretion. Of the soluble transition metals in ROFA (nickel, iron, vanadium), only vanadium individually, or combinations of the metals containing vanadium, provoked secretion. The results suggest ROFA enhances mucin secretion and generates toxicity in vitro to airway epithelium via a mechanism(s) involving generation of oxidant stress, perhaps related to depletion of cellular antioxidant capacity. Deleterious effects of inhalation of ROFA in the respiratory tract in vivo may relate to these cellular

Modeling and Prediction of Coal Ash Fusion Temperature based on BP Neural Network

Directory of Open Access Journals (Sweden)

Miao Suzhen

2016-01-01

Full Text Available Coal ash is the residual generated from combustion of coal. The ash fusion temperature (AFT of coal gives detail information on the suitability of a coal source for gasification procedures, and specifically to which extent ash agglomeration or clinkering is likely to occur within the gasifier. To investigate the contribution of oxides in coal ash to AFT, data of coal ash chemical compositions and Softening Temperature (ST in different regions of China were collected in this work and a BP neural network model was established by XD-APC PLATFORM. In the BP model, the inputs were the ash compositions and the output was the ST. In addition, the ash fusion temperature prediction model was obtained by industrial data and the model was generalized by different industrial data. Compared to empirical formulas, the BP neural network obtained better results. By different tests, the best result and the best configurations for the model were obtained: hidden layer nodes of the BP network was setted as three, the component contents (SiO2, Al2O3, Fe2O3, CaO, MgO were used as inputs and ST was used as output of the model.

Characterization of ashes of elephant grass (Pennisetum purpureum) for potential added in mass red ceramic

International Nuclear Information System (INIS)

Silva, A.M.F.D.; Sales, K.A.; Monteiro, S.N.; Vieira, C.M.F.

2012-01-01

This work is in characterizing ash from biomass grass (Pennisetum purpureums) for incorporation into red ceramic masses. The ashes of elephant grass were generated from burning this dry biomass in an industrial furnace of red ceramic. The morphology of the material generated was observed by an optical microscope. The chemical composition was determined by fluorescence X-ray spectrometry, and the identification of phases by X-ray diffraction. The particle size distribution was obtained by sieving. Thermogravimetric analyzes were also conducted. The results indicate that these ashes are constituted of high quantities of SiO 2 , MgO, CaO and K 2 O, totaling approximately 75% of composition of matter. They have a particle size of 0.7 to 2.2mm featuring. The residue as a kind of coarse particles. Therefore, the results of this study can support future research to the addition of this residue in structural ceramics products (red ceramic)

Recovery of vanadium, and nickel from fly ash produced from heavy oil-fired electrical power station

International Nuclear Information System (INIS)

Stas, J.; Dahdouh, A.; Al-Chayah, O.

2006-05-01

After some preliminary tests, two leaching stages of fly ash to recover vanadium, molybdenum and nickel were selected. A first stage alkaline leaching of fly ash to recover vanadium and molybdenum followed by a second stage sulfuric acid leaching of the residual ash to recover nickel. The impact of some operational parameters (L/S, leaching temperature, mixing time, and agent leaching concentrations) on the recovery of V, Ni was investigated. Conditions of precipitation of V and Mo from alkaline medium and Ni from sulfuric acid solution were established. (author)

Protecting black ash from the emerald ash borer

Science.gov (United States)

Les Benedict

2010-01-01

Black ash (Fraxinus nigra) is an important resource for Tribes in the Northeast and Great Lakes regions of the North American continent. Ash in North America is being threatened with widespread destruction as a result of the introduction of emerald ash borer beetle (Agrilus planipennis) in 2002. Measures are being taken to slow the spread of emerald ash borer beetle....

Fly ash leachate generation and qualitative trends at Ohio test sites

Energy Technology Data Exchange (ETDEWEB)

Solc, J.; Foster, H.J.; Butler, R.D. [Energy & Environmental Research Center, Grand Forks, ND (United States)

1995-12-01

Under the sponsorship of the U.S. Department of Energy, the environmental impact and potential contamination from landfilled fly ash (coal conversion solid residues - CCSRs) have been studied at field sites in Ohio. The progressive increase of moisture content within pilot cells over depth and time facilitated intensive chemical processes and generation of highly alkaline (pH of 10 to 12) leachate. Chemistry of pore water from lysimeters and ASTM leachate from fly ash and soil cores indicate the leachate potential to migrate out of deposit and impact the pore water quality of surrounding soils. Na, SO{sub 4} and, particularly, K, Cl, pH, and EC appeared to be valuable indicator parameters for tracking potential leachate transport both within the cells and below the ash/soil interface.

Sugarcane bagasse ash reinforced HDPE composites: effects of electron-beam radiation crosslinking on tensile and morphological properties

Energy Technology Data Exchange (ETDEWEB)

Teixeira, Jaciele G.; Gomes, Michelle G.; Oliveira, Rene R.; Silva, Valquiria A.; Sartori, Mariana M.; Ortiz, Angel V.; Moura, Esperidiana A.B., E-mail: jacielegteixeira@yahoo.com [Instituto de Pesquisas Energeticas e Nucleares (IPEN-CNEN/SP), Sao Paulo, SP (Brazil)

2013-07-01

Environmental issues have led to the development of polymeric materials reinforced with fibers originated from renewable agricultural sources such as pineapple leaf, sisal, jute, piassava, coir, and sugarcane bagasse. Although sugarcane bagasse fiber residues has been extensively studied and used as a source of reinforcement of polymers, the major portion of these residues is currently burnt for energy supply in the sugar and alcohol industries and as a result of its burning, tons of ashes are produced. Due to the inorganic composition, ashes can be used as reinforcement in polymeric materials. This study presents the preparation and characterization of a composite based on HDPE matrix and sugarcane bagasse ashes as reinforcement cross-linked by electron-beam radiation. The HDPE /Ash composite (95:5 wt %) was obtained by using a twin-screw extruder machine followed by injection molding. After extrusion and injection molding process, the composites were subjected to electron-beam radiation, at radiation doses of 150 kGy and 250 kGy using a Dynamitron electron beam accelerator, at room temperature in the presence of air. The irradiated and non-irradiated composite specimens were characterization by tensile and MFI tests, scanning electron microscopy (SEM), X-ray diffraction (XRD) and sol-gel analysis. In addition, ash from bagasse fiber was characterized by WDXRF. (author)

Sugarcane bagasse ash reinforced HDPE composites: effects of electron-beam radiation crosslinking on tensile and morphological properties

International Nuclear Information System (INIS)

Teixeira, Jaciele G.; Gomes, Michelle G.; Oliveira, Rene R.; Silva, Valquiria A.; Sartori, Mariana M.; Ortiz, Angel V.; Moura, Esperidiana A.B.

2013-01-01

Environmental issues have led to the development of polymeric materials reinforced with fibers originated from renewable agricultural sources such as pineapple leaf, sisal, jute, piassava, coir, and sugarcane bagasse. Although sugarcane bagasse fiber residues has been extensively studied and used as a source of reinforcement of polymers, the major portion of these residues is currently burnt for energy supply in the sugar and alcohol industries and as a result of its burning, tons of ashes are produced. Due to the inorganic composition, ashes can be used as reinforcement in polymeric materials. This study presents the preparation and characterization of a composite based on HDPE matrix and sugarcane bagasse ashes as reinforcement cross-linked by electron-beam radiation. The HDPE /Ash composite (95:5 wt %) was obtained by using a twin-screw extruder machine followed by injection molding. After extrusion and injection molding process, the composites were subjected to electron-beam radiation, at radiation doses of 150 kGy and 250 kGy using a Dynamitron electron beam accelerator, at room temperature in the presence of air. The irradiated and non-irradiated composite specimens were characterization by tensile and MFI tests, scanning electron microscopy (SEM), X-ray diffraction (XRD) and sol-gel analysis. In addition, ash from bagasse fiber was characterized by WDXRF. (author)

Preparation Of Pure Carbon From Heavy Oil Fly Ash

International Nuclear Information System (INIS)

ABU ZAID, A.H.M.

2010-01-01

The Egyptian production of heavy oil is approximately 12 million tons of heavy oil per year and approximately 5.3 million tons of this amount is used as fuel in the electric power stations. Based on the fact that the ash content of Egyptian heavy oil is approximately 0.2 %, about 10600 tons of fly ash is produced per/year which causes a lot of environmental problems such as dusting, release of the acidic liquids and heavy metals such as vanadium, nickel, zinc and unburned carbon. Treatment of fly ash by leaching of vanadium and zinc was carried out under different conditions to achieve the best leaching efficiency of both vanadium and zinc by sodium hydroxide. The leaching efficiency obtained was 91% for vanadium and 98% for zinc. This study was concerned with the precipitation of zinc at pH 7.5 as zinc hydroxide and the precipitation of vanadium as ammonium metavanadate at pH 8.5. Leaching of nickel, iron and other elements from the residue was carried out by 2M HCl under different conditions. The achieved leaching efficiency of nickel was 95% where as that of iron was 92%. Precipitation efficiency of both nickel and iron were 99.9%. The residue, which contains mainly unburned carbon, have been washed two times with water and dried at 200 o C then ground to < 300μm. According to the achieved analysis of the obtained carbon, it can be characterized as pure carbon

MSWI boiler fly ashes: magnetic separation for material recovery.

Science.gov (United States)

De Boom, Aurore; Degrez, Marc; Hubaux, Paul; Lucion, Christian

2011-07-01

Nowadays, ferrous materials are usually recovered from Municipal Solid Waste Incineration (MSWI) bottom ash by magnetic separation. To our knowledge, such a physical technique has not been applied so far to other MSWI residues. This study focuses thus on the applicability of magnetic separation on boiler fly ashes (BFA). Different types of magnet are used to extract the magnetic particles. We investigate the magnetic particle composition, as well as their leaching behaviour (EN 12457-1 leaching test). The magnetic particles present higher Cr, Fe, Mn and Ni concentration than the non-magnetic (NM) fraction. Magnetic separation does not improve the leachability of the NM fraction. To approximate industrial conditions, magnetic separation is also applied to BFA mixed with water by using a pilot. BFA magnetic separation is economically evaluated. This study globally shows that it is possible to extract some magnetic particles from MSWI boiler fly ashes. However, the magnetic particles only represent from 23 to 120 g/kg of the BFA and, though they are enriched in Fe, are composed of similar elements to the raw ashes. The industrial application of magnetic separation would only be profitable if large amounts of ashes were treated (more than 15 kt/y), and the process should be ideally completed by other recovery methods or advanced treatments. Copyright © 2011 Elsevier Ltd. All rights reserved.

Heavy metal removal from produced water using retorted shale; Remocao de metais pesados em aguas produzidas utilizando xisto retortado

Energy Technology Data Exchange (ETDEWEB)

Pimentel, Patricia M.; Melo, Marcos A.F.; Melo, Dulce M.A.; Silva Junior, Carlos N.; Assuncao, Ary L.C. [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil); Anjos, Marcelino J. [Universidade Federal, Rio de Janeiro, RJ (Brazil). Coordenacao dos Programas de Pos-graduacao de Engenharia

2004-07-01

The Production of oil and gas is usually accompanied by the production of large volume of water that can have significant environmental effects if not properly treated. In this work, the use of retort shale was investigated as adsorbent agent to remove heavy metals in produced water. Batch adsorption studies in synthetic solution were performed for several metal ions. The efficiency removal was controlled by solution pH, adsorbent dosage, and initial ion concentration and agitation times. Two simple kinetic models were used, pseudo-first- and second-order, were tested to investigate the adsorption mechanisms. The equilibrium data fitted well with Langmuir and Freundlich models. The produced water samples were treated by retorted shale under optimum adsorption conditions. Synchrotron radiation total reflection X-ray fluorescence was used to analyze the elements present in produced water samples from oil field in Rio Grande do Norte, Brazil. The removal was found to be approximately 20-50% for Co, Ni, Sr and above 80% for Cr, Ba, Hg and Pb. (author)

Leaching and soil/groundwater transport of contaminants from coal combustion residues

International Nuclear Information System (INIS)

Hjelmar, O.; Hansen, E.A.; Larsen, F.; Thomassen, H.

1992-01-01

In this project the results of accelerated laboratory leaching tests on coal fly ash and flue gas desulfurization (FGD) products from the spray dryer absorption process (SDA) were evaluated by comparison to the results of large scale lysimeter leaching tests on the same residues. The mobility of chromium and molybdenum - two of the kev contaminants of coal combustion residue leachates - in various typical soil types was investigated by batch and column methods in the laboratory. Some of the results were confirmed by field observations at an old coal fly ash disposal site and by a lysimeter attenuation test with coal fly ash leachate on a clayed till. A large number of groundwater transport models and geochemical models were reviewed, and two of the models (Gove-Stollenwerk and CHMTRNS) were modified and adjusted and used to simulate column attenuation tests performed in the laboratory. One of the models (Grove-Stollenwerk) was used to illustrate a recommended method of environmental impact assessment, using lysimeter leaching data and laboratory column attenuation data to describe the emission and migration of Mo from a coal fly ash disposal site

Engineering Behavior and Characteristics of Wood Ash and Sugarcane Bagasse Ash

Directory of Open Access Journals (Sweden)

Francisco Grau

2015-10-01

Full Text Available Biomasses are organic materials that are derived from any living or recently-living structure. Plenty of biomasses are produced nationwide. Biomasses are mostly combusted and usually discarded or disposed of without treatment as biomass ashes, which include wood and sugarcane bagasse ashes. Thus, recycling or treatment of biomass ashes leads to utilizing the natural materials as an economical and environmental alternative. This study is intended to provide an environmental solution for uncontrolled disposal of biomass ashes by way of recycling the biomass ash and replacing the soils in geotechnical engineering projects. Therefore, in this study, characteristic tests of wood and sugarcane bagasse ashes that are considered the most common biomass ashes are conducted. The test of chemical compositions of biomass ashes is conducted using energy dispersive X-ray spectroscopy (EDS, and Scanning Electron Microscope (SEM, and heavy metal analysis is also conducted. Engineering behaviors including hydraulic conductivity, constrained modulus and shear modulus are examined. Also, coal fly ash Class C is used in this study for comparison with biomass ashes, and Ottawa 20/30 sands containing biomass ashes are examined to identify the soil replacement effect of biomass ashes. The results show that the particle sizes of biomass ashes are halfway between coal fly ash Class C and Ottawa 20/30 sand, and biomass ashes consist of a heterogeneous mixture of different particle sizes and shapes. Also, all heavy metal concentrations were found to be below the US Environmental Protection Agency (EPA maximum limit. Hydraulic conductivity values of Ottawa 20/30 sand decrease significantly when replacing them with only 1%–2% of biomass ashes. While both the constrained modulus and shear modulus of biomass ashes are lower than Ottawa 20/30 sand, those of mixtures containing up to 10% biomass ashes are little affected by replacing the soils with biomass ashes.

Utilization of residues from firing with biofuels

Energy Technology Data Exchange (ETDEWEB)

Moberg, P O; Nelson, B; Sjoeberg, A

1983-10-01

The aim of the project is to analyse various possibilities of using residues from firing with biofuels, to assess the environmental consequences of such use and to prepare proposal and programme for investigations and tests concerning the use and its environmental consequences. Peat fly ashes have been tested in making concrete with promising results. On the other hand it is doubtful if wood ashes can be used, as the lime content is high. Generally can be said that ashes from biofuels are produced by many small combustion plants and that the quality is unequal. It should be possible to use fly ashes as well as bottom ashes from biofuels as borrow material in road works and construction works. Lime and cement are binders used for stabilization of gravel, sand and clay. Coal fly ashes can partly substitute such binders. Ground stabilization is usual in connection with road construction. It is also probable that fly ashes from biofuels can partly be substituted for cement and lime. Higher prices can be obtained for bio ashes used as binders than used as borrow material. Especially wood ashes are considered to be valuable as forest manure. The value roughly estimated by means of comparison to fertilizer is 400 - 800 SEK/ton. Bottom ashes which are an important part of the total ash production have low contents of heavy metals and are thus perhaps suitable for agricultural use. It seems to be possible to substitute fly ashes from biofuel for part of the precipitation chemicals used for reduction of phosphorus and for sludge conditioning at the local water treatment plants. The estimated Swedish production of wood ashes in 1990 could account for 10 per cent of the present production of potash in Europe. There is a need to cover old tailingponds of rests of sulphide ore with an alkaline and dense material. Locally (Dalecarlia) the good properties of fly ashes for this purpose should be utilized.

Risks of toxic ash from artisanal mining of discarded cellphones

Energy Technology Data Exchange (ETDEWEB)

Hibbert, Kathleen [School of Social Ecology, University of California, Irvine, CA 92697 (United States); Ogunseitan, Oladele A., E-mail: Oladele.Ogunseitan@uci.edu [School of Social Ecology, University of California, Irvine, CA 92697 (United States); Department of Population Health and Disease Prevention, Program in Public Health, University of California, Irvine, CA 92697 (United States)

2014-08-15

Highlights: • We simulated artisanal incineration of four component categories of cellphones. • We identified metals and organic chemicals in the resulting electronic waste ash. • We used USETox model to demonstrate potential ecotoxicity and human health impacts. • We identify targets for risk reduction for hazardous chemicals in cellphones. - Abstract: The potential environmental and human health impacts of artisanal mining of electronic waste through open incineration were investigated. A market-representative set of cellphones was dismantled into four component categories—batteries, circuit boards, plastics and screens. The components were shredded, sieved and incinerated at 743–818 °C. The concentrations of 17 metals were determined using U.S. EPA methods 6010C (inductively coupled plasma-atomic emission spectrometry; 6020A (inductively coupled plasma-mass spectrometry, or 7471B and 7470A (cold-vapor atomic absorption). EPA Method 8270 (gas chromatography/mass spectrometry) was used to identify polyaromatic hydrocarbon compounds and polybrominated diphenyl ethers. EPA Method 8082A was used to measure polychlorinated biphenyls and EPA Method 8290 was used for dioxin/furans in the residue ash. The life cycle assessment model USEtox{sup ®} was used to estimate impacts of the ash residue chemicals on human health and the ecosystem. Among metals, copper in printed circuit boards had the highest ecotoxicity impact (1610–1930 PAF m{sup 3}/kg); Beryllium in plastics had the highest impact on producing non-cancer diseases (0.14–0.44 cases/kg of ash); and Nickel had the largest impact on producing cancers (0.093–0.35 cases/kg of ash). Among organic chemicals, dioxins from incinerated batteries produced the largest ecotoxicological impact (1.07E − 04 to 3.64E − 04 PAF m{sup 3}/kg). Furans in incinerated batteries can generate the largest number of cancers and non-cancer diseases, representing 8.12E − 09 to 2.28E − 08 and 8.96E − 10 and 2.52E

Risks of toxic ash from artisanal mining of discarded cellphones

International Nuclear Information System (INIS)

Hibbert, Kathleen; Ogunseitan, Oladele A.

2014-01-01

Highlights: • We simulated artisanal incineration of four component categories of cellphones. • We identified metals and organic chemicals in the resulting electronic waste ash. • We used USETox model to demonstrate potential ecotoxicity and human health impacts. • We identify targets for risk reduction for hazardous chemicals in cellphones. - Abstract: The potential environmental and human health impacts of artisanal mining of electronic waste through open incineration were investigated. A market-representative set of cellphones was dismantled into four component categories—batteries, circuit boards, plastics and screens. The components were shredded, sieved and incinerated at 743–818 °C. The concentrations of 17 metals were determined using U.S. EPA methods 6010C (inductively coupled plasma-atomic emission spectrometry; 6020A (inductively coupled plasma-mass spectrometry, or 7471B and 7470A (cold-vapor atomic absorption). EPA Method 8270 (gas chromatography/mass spectrometry) was used to identify polyaromatic hydrocarbon compounds and polybrominated diphenyl ethers. EPA Method 8082A was used to measure polychlorinated biphenyls and EPA Method 8290 was used for dioxin/furans in the residue ash. The life cycle assessment model USEtox ® was used to estimate impacts of the ash residue chemicals on human health and the ecosystem. Among metals, copper in printed circuit boards had the highest ecotoxicity impact (1610–1930 PAF m 3 /kg); Beryllium in plastics had the highest impact on producing non-cancer diseases (0.14–0.44 cases/kg of ash); and Nickel had the largest impact on producing cancers (0.093–0.35 cases/kg of ash). Among organic chemicals, dioxins from incinerated batteries produced the largest ecotoxicological impact (1.07E − 04 to 3.64E − 04 PAF m 3 /kg). Furans in incinerated batteries can generate the largest number of cancers and non-cancer diseases, representing 8.12E − 09 to 2.28E − 08 and 8.96E − 10 and 2.52E − 09 cases

Levels of 137Cs and 40K in wood ash-amended soils

International Nuclear Information System (INIS)

Ohno, Tsutomu; Hess, C.T.

1994-01-01

Wood ash is a residual material produced at an annual rate of 1.5-3.0 million tons by wood burning power plants in the USA. Up to 80% of the wood ash generated in northeastern USA is landspread on agricultural soils. Recently, concern has arisen regarding the 137 Cs content of wood ash and levels of 137 Cs of wood ash-amended soils. The 137 Cs originated primarily from above ground nuclear weapons testing in the 1950s and 1960s. This study examined the total and pH 3, NH 4 OAc extractable levels of 137 Cs and 40 K in three soils incubated in the laboratory with 0, 3 and 9 g of wood ash on a calcium carbonate equivalence basis kg -1 soil. The wood ash contained 137 Cs and 40 K at 3920 and 21'700 pCi kg -1 , respectively. At the regulated wood ash application rate limit, 3 g wood ash (calcium carbonate equivalent basis) kg -1 of soil, there was no statistical difference from the control treatment in both total and soluble 137 Cs and 40 K levels. For one soil, there was an increase in the 137 Cs level when wood ash was amended at 9 g wood ash (calcium carbonate equivalent basis) kg -1 soil. The 137 Cs was strongly bound to the cation exchange sites of the soils with the average fraction soluble in pH 3, NH 4 OAc solution at 4.8% in the mineral soils and 0.9% in the organic soil. Considering the current limits on permitted wood ash application rates to soils, there was no statistically significant effect on the levels of 137 Cs or 40 K found in wood ash-amended soils

Yields from pyrolysis of refinery residue using a batch process

Directory of Open Access Journals (Sweden)

S. Prithiraj

2017-12-01

Full Text Available Batch pyrolysis was a valuable process of assessing the potential of recovering and characterising products from hazardous waste materials. This research explored the pyrolysis of hydrocarbon-rich refinery residue, from crude oil processes, in a 1200 L electrically-heated batch retort. Furthermore, the off-gases produced were easily processed in compliance with existing regulatory emission standards. The methodology offers a novel, cost-effective and environmentally compliant method of assessing recovery potential of valuable products. The pyrolysis experiments yielded significant oil (70% with high calorific value (40 MJ/kg, char (14% with carbon content over 80% and non-condensable gas (6% with significant calorific value (240 kJ/mol. The final gas stream was subjected to an oxidative clean-up process with continuous on-line monitoring demonstrating compliance with South African emission standards. The gas treatment was overall economically optimal as only a smaller portion of the original residue was subjected to emission-controlling steps. Keywords: Batch pyrolysis, Volatiles, Oil yields, Char, Emissions, Oil recovery

Quality and shelf life of buffalo meat blocks processed in retort pouches.

Science.gov (United States)

Devadason, I Prince; Anjaneyulu, A S R; Mendirtta, S K; Murthy, T R K

2014-12-01

The shelf life of buffalo meat blocks processed in 3-ply retort pouches at Fo = 12.13 in a stock sterilizer were evaluated at 15 days interval for physico-chemical, microbiological and sensory attributes for a period of 3 months. The pH of the product was 6.28 at 0 day and a gradual decline was noticed during storage. Texture of the product as indicated by shear force values had decreased slowly. The residual nitrite content had significantly declined from 82.67 ppm at 0 day to 45.00 ppm on 90th day of storage. The TBARS values were 0.24 and 0.67 mg malonaldehyde/kg, respectively at 0 day and 90 days of storage. Tyrosine value had significantly increased from 0.37 mg/100 g at 0 day to 0.58 mg/100 g during storage. Free aminoacid content increased gradually from an initial level of 124.32 to 217.51 at 90(th) day of storage. The SDS-PAGE hydrolysis pattern showed barely discernible 205 KDa protein and presence of subfragments in the molecular range of 63 KDa to 29 KDa protein. The sensory studies indicated that the products were well acceptable up to a period of 90 days. As the storage period increased pH, reidual nitrite, sensory attributes declined significantly and TBARS value, tyrosine value and free aminoacid content significantly increased. Mesophillic aerobes and anerobes were found to be absent. The shelf life study indicated that the products were well acceptable up to a period of 90 days based on the assessment of physico-chemical, microbiological and sensory attributes.

Characteristic and antioxidant activity of retorted gelatin hydrolysates from cobia (Rachycentron canadum) skin.

Science.gov (United States)

Yang, Jing-Iong; Ho, Hsin-Yi; Chu, Yuh-Jwo; Chow, Chau-Jen

2008-09-01

Alkali-pretreated cobia (Rachycentron canadum) skin was extracted in a retort (121°C) for 30min to obtain a retorted skin gelatin hydrolysate (RSGH). The molecular mass distributions and antioxidant activities of cobia RSGH and enzyme-treated RSGHs (ET-RSGHs) derived from bromelain, papain, pancreatin, and trypsin digestion were then characterized. The molecular mass distribution of the RSGH ranged mainly between 20,000 and 700Da and those of ET-RSGHs ranged between 6500 and 700Da. The DPPH (α,α-diphenyl-β-picrylhydrazyl) radical scavenging effects (%) of 10mg/ml of RSGH and 10mg/ml of the four ET-RSGHs were 55% and 51-61%, respectively. The lipid peroxidation inhibition (%) of RSGH and ET-RSGHs (10mg/ml) were 58% and 60-71% on the fifth day in a linoleic acid model system, respectively. The 3Kd-ET-RSGHs, obtained by using a series of centrifugal ultrafiltration filters (molecular weight cut-offs of 10, 5, and 3kDa done sequentially with decreasing pore size), exhibited dramatically improved antioxidant activity, with most of the molecular mass ranging below 700Da. Compared to 10mg/ml of the RSGH, 10mg/ml of 3Kd-ET-RSGHs exhibited 45-65% more scavenging of DPPH radical and 24-38% more inhibition of lipid peroxidation. The peptides with molecular masses below 700Da in the ET-RSGHs or 3Kd-ET-RSGHs significantly affect the antioxidant properties. These peptides are composed of a small number of amino acids or free amino acids and have the potential to be added as antioxidants in foods. Copyright © 2008 Elsevier Ltd. All rights reserved.

Life cycle assessment of disposal of residues from municipal solid waste incineration

DEFF Research Database (Denmark)

Birgisdottir, Harpa; Bhander, Gurbakhash Singh; Hauschild, Michael Zwicky

2007-01-01

Two disposal methods for MSWI bottom ash were assessed in a new life cycle assessment (LCA) model for road construction and disposal of residues. The two scenarios evaluated in the model were: (i) landfilling of bottom ash in a coastal landfill in Denmark and (ii) recycling of bottom ash as subbase...... layer in an asphalted secondary road. The LCA included resource and energy consumption, and emissions associated with upgrading of bottom ash, transport, landfilling processes, incorporation of bottom ash in road, substitution of natural gravel as road construction material and leaching of heavy metals...... and salts from bottom ash in road as well as in landfill. Environmental impacts associated with emissions to air, fresh surface water, marine surface water, groundwater and soil were aggregated into 12 environmental impact categories: Global Warming, Photochemical Ozone Formation, Nutrient Enrichment...

Optoelectronic system of online measurements of unburned carbon in coal fly ash

Science.gov (United States)

Golas, Janusz; Jankowski, Henryk; Niewczas, Bogdan; Piechna, Janusz; Skiba, Antoni; Szkutnik, Wojciech; Szkutnik, Zdzislaw P.; Wartak, Ryszarda; Worek, Cezary

2001-08-01

Carbon-in-ash level is an important consideration for combustion efficiency as well as ash marketing. The optoelectronic analyzing system for on-line determination and monitoring of the u burned carbon content of ash samples is presented. The apparatus operates on the principle that carbon content is proportional to the reflectance of IR light. Ash samples are collected iso kinetically from the flue gas duct and placed in a sample tube with a flat glass bottom. The same is then exposed to a light. The reflectance intensity is used by the system's computer to determine residual carbon content from correlation curves. The sample is then air purged back to the duct or to the attached sample canister to enable laboratory check analysis. The total cycle time takes between 5 and 10 minutes. Real time result of carbon content with accuracy 0.3-0.7 percent are reported and can be used for boiler controlling.

Environmental assessment of incinerator residue utilisation.

Science.gov (United States)

Toller, S; Kärrman, E; Gustafsson, J P; Magnusson, Y

2009-07-01

Incineration ashes may be treated either as a waste to be dumped in landfill, or as a resource that is suitable for re-use. In order to choose the best management scenario, knowledge is needed on the potential environmental impact that may be expected, including not only local, but also regional and global impact. In this study, A life cycle assessment (LCA) based approach was outlined for environmental assessment of incinerator residue utilisation, in which leaching of trace elements as well as other emissions to air and water and the use of resources were regarded as constituting the potential environmental impact from the system studied. Case studies were performed for two selected ash types, bottom ash from municipal solid waste incineration (MSWI) and wood fly ash. The MSWI bottom ash was assumed to be suitable for road construction or as drainage material in landfill, whereas the wood fly ash was assumed to be suitable for road construction or as a nutrient resource to be recycled on forest land after biofuel harvesting. Different types of potential environmental impact predominated in the activities of the system and the use of natural resources and the trace element leaching were identified as being relatively important for the scenarios compared. The scenarios differed in use of resources and energy, whereas there is a potential for trace element leaching regardless of how the material is managed. Utilising MSWI bottom ash in road construction and recycling of wood ash on forest land saved more natural resources and energy than when these materials were managed according to the other scenarios investigated, including dumping in landfill.

Life cycle adaption of biofuel ashes. Evaluation of new techniques for pelletizing of biofuel ashes, especially regarding operational properties and environmental effects in the forest after ash recycling. Stage 1

International Nuclear Information System (INIS)

Loevgren, Linnea; Lundmark, Jan-Erik; Jansson, Charlotta

2000-11-01

The aim of the project 'Adaptation of Wood Ashes to Recycling' is to evaluate a new technique - roll pelleting - for making wood ash suitable for reuse as a fertiliser for woodland. The project is being carried out at the forest product companies AssiDomaen and Stora Enso. The main financier is the Swedish National Energy Administration. Other financiers are AssiDomaen, Stora Enso, The Thermal Engineering Research Institute and The Forestry Research Institute of Sweden. The project has involved the construction of a full-scale roll pelleter in a mobile container and its trial operation at two Swedish pulp and paper mills. The leaching properties of the ash products were studied with a laboratory method. In addition, the effects of ash fertilisation with these products are being studied in a four-year field trial. Effects on soil pH, nutrient supply, soil water chemistry and ground vegetation are being evaluated by The Forestry Research Institute of Sweden and will be reported separately in the year 2003. In a laboratory prestudy, the leaching properties of pellets from twelve different ash products made in a laboratory prototype machine were evaluated. The ash products were made from residues from the AssiDomaen Froevi mill and the Stora Enso Fors mill. Fly ash from Froevi was used alone and mixed with green liquor sludge and lime sludge respectively. Fly ash from Fors was also used alone and mixed with coating colour. The laboratory method used for the evaluation of leaching properties is the method developed by IVL The Swedish Environmental Research Institute Ltd. The results show that the progress of the leaching of roll pelleted ash is significantly slower than for the corresponding crushed product and a reference lime product. The speed of leaching, measured as acid neutralisation capacity, ANC, was significantly lower for the roll pelleted ash compared to self-hardened and crushed ash products. Because of the high content of calcium, lime has on the whole, a

Interaction of acid mine drainage with Ordinary Portland Cement blended solid residues generated from active treatment of acid mine drainage with coal fly ash.

Science.gov (United States)

Gitari, Wilson M; Petrik, Leslie F; Key, David L; Okujeni, Charles

2011-01-01

Fly ash (FA) has been investigated as a possible treatment agent for Acid mine drainage (AMD) and established to be an alternative, cheap and economically viable agent compared to the conventional alkaline agents. However, this treatment option also leads to generation of solid residues (SR) that require disposal and one of the proposed disposal method is a backfill in coal mine voids. In this study, the interaction of the SR with AMD that is likely to be present in such backfill scenario was simulated by draining columns packed with SR and SR + 6% Ordinary Portland Cement (OPC) unsaturated with simulated AMD over a 6 month period. The evolving geochemistry of the liquid/solid (L/S) system was evaluated in-terms of the mineral phases likely or controlling contaminants attenuation at the different pH regimes generated. Stepwise acidification of the percolates was observed as the drainage progressed. Two pH buffer zones were observed (7.5-9 and 3-4) for SR and (11.2-11.3 and 3.5-4) for SR + 6% OPC. The solid residue cores (SR) appeared to have a significant buffering capacity, maintaining a neutral to slightly alkaline pH in the leachates for an extended period of time (97 days: L/S 4.3) while SR + 6% OPC reduced this neutralization capacity to 22 days (L/S 1.9). Interaction of AMD with SR or SR + 6% OPC generated alkaline conditions that favored precipitation of Fe, Al, Mn-(oxy) hydroxides, Fe and Ca-Al hydroxysulphates that greatly contributed to the contaminants removal. However, precipitation of these phases was restricted to the pH of the leachates remaining at neutral to circum-neutral levels. Backfill of mine voids with SR promises to be a feasible technology for the disposal of the SR but its success will greatly depend on the disposal scenario, AMD generated and the alkalinity generating potential of the SR. A disadvantage would be the possible re-dissolution of the precipitated phases at pH water column. However extrapolation of this concept to a field

Characterisation of ashes produced by co-combustion of recovered fuels and peat

Energy Technology Data Exchange (ETDEWEB)

Frankenhaeuser, M. [Borealis Polymers Oy, Porvoo (Finland)

1997-10-01

The current project focuses on eventual changes in ash characteristics during co-combustion of refuse derived fuel with coal, peat, wood or bark, which could lead to slagging, fouling and corrosion in the boiler. Ashes were produced at fluidised bed (FB) combustion conditions in the 15 kW reactor at VTT Energy, Jyvaeskylae, the fly ash captured by the cyclone was further analysed by XRF at Outokumpu Geotechnical Laboratory, Outokumpu. The sintering behaviour of these ashes was investigated using a test procedure developed at the Combustion Chemistry Research Group at Aabo Akademi University. The current extended programme includes a Danish refuse-derived fuel (RDF), co-combusted with bark/coal (5 tests) and wood/coal (2 tests), a RF from Jyvaskyla (2 tests with peat/coal) and de-inking sludges co- combusted at full-scale with wood waste or paper mill sludge (4 ashes provided by IVO Power). Ash pellets were thermally treated in nitrogen in order to avoid residual carbon combustion. The results obtained show no sintering tendencies below 600 deg C, significant changes in sintering are seen with pellets treated at 1000 deg C. Ash from 100 % RDF combustion does not sinter, 25 % RDF co-combustion with wood and peat, respectively, gives an insignificant effect. The most severe sintering occurs during co-combustion of RDF with bark. Contrary to the earlier hypothesis a 25 % coal addition seems to have a negative effect on all fuel blends. Analysis of the sintering results versus ash chemical composition shows, that (again), in general, an increased level of alkali chlorides and sulphates gives increased sintering. Finally, some results on sintering tendency measurements on ashes from full-scale CFB co-combustion of deinking sludge with wood waste and paper mill sludge are given. This shows that these ashes show very little, if any, sintering tendency, which can be explained from ash chemistry

Ash Utilisation 2012. Ashes in a Sustainable Society. Proceedings

Energy Technology Data Exchange (ETDEWEB)

NONE

2012-11-01

Conference themes: Risk assessment, Fly ash- Road construction, Recycling and Greenhouse gases, Storage of ashes, Fertilizer, Metal Mining, Support and Barriers, Construction Material, Civil Engineering, and MSWI bottom ash.

The development of an integrated multistaged fluid-bed retorting process. Final report, September 1990--August 1994

Energy Technology Data Exchange (ETDEWEB)

Carter, S.D.; Taulbee, D.N.; Stehn, J.L.; Vego, A.; Robl, T.L.

1995-02-01

This summarizes the development of the KENTORT II retorting process, which includes integral fluidized bed zones for pyrolysis, gasification, and combustion of oil shale. Purpose was to design and test the process at the 50-lb/hr scale. The program included bench- scale studies of coking and cracking reactions of shale oil vapors over processed shale particles to address issues of scaleup associated with solid-recycle retorting. The bench-scale studies showed that higher amounts of carbon coverage reduce the rate of subsequent carbon deposition by shale oil vapors onto processed shale particles; however carbon-covered materials were also active in terms of cracking and coking. Main focus was the 50-lb/hr KENTORT II PDU. Cold-flow modeling and shakedown were done before the PDU was made ready for operation. Seven mass-balanced, steady-state runs were completed within the window of design operating conditions. Goals were achieved: shale feedrate, run duration (10 hr), shale recirculation rates (4:1 to pyrolyzer and 10:1 to combustor), bed temperatures (pyrolyzer 530{degree}C, gasifier 750{degree}C, combustor 830{degree}C), and general operating stability. Highest oil yields (up to 109% of Fischer assay) were achieved for runs lasting {ge} 10 hours. High C content of the solids used for heat transfer to the pyrolysis zone contributed to the enhanced oil yield achieved.

Ash behavior during hydrothermal treatment for solid fuel applications. Part 1: Overview of different feedstock

International Nuclear Information System (INIS)

Mäkelä, Mikko; Fullana, Andrés; Yoshikawa, Kunio

2016-01-01

Highlights: • Ash behavior of 29 different feedstock interpreted using multivariate data analysis. • Two different groups identified based on char ash content and ash yield. • Solubility of individual elements evaluated based on a smaller data set. • Ash from industrial sludge contained anthropogenic metals with low solubility. - Abstract: Differences in ash behavior during hydrothermal treatment were identified based on multivariate data analysis of literature information on 29 different feedstock. In addition, the solubility of individual elements was evaluated based on a smaller data set. As a result two different groups were distinguished based on char ash content and ash yield. Virgin terrestrial and aquatic biomass, such as different types of wood and algae, in addition to herbaceous and agricultural biomass, bark, brewer’s spent grain, compost and faecal waste showed lower char ash content than municipal solid wastes, anaerobic digestion residues and municipal and industrial sludge. Lower char ash content also correlated with lower ash yield indicating differences in chemical composition and ash solubility. Further evaluation of available data showed that ash in industrial sludge mainly contained anthropogenic Al, Fe and P or Ca and Si with low solubility during hydrothermal treatment. Char from corn stover, miscanthus, switch grass, rice hulls, olive, artichoke and orange wastes and empty fruit bunch had generally higher contents of K, Mg, S and Si than industrial sludge although differences existed within the group. In the future information on ash behavior should be used for enhancing the fuel properties of char based on feedstock type and hydrothermal treatment conditions.

Plutonium recovery from incinerator ash and centrifuge sludge by peroxide fusion

International Nuclear Information System (INIS)

Partridge, J.A.; Wheelwright, E.J.

1975-05-01

A technique was demonstrated for solubilizing the plutonium contained in incinerator ash and in other waste solids (such as solids accumulated by centrifugation after solvent extraction contacts in the plutonium reclamation facility at Hanford). A sodium hydroxide--sodium peroxide fusion is performed on the Pu-containing solids. The cooled melt is then dissolved in dilute nitric acid. Mild steel cans were used as ''single use'' crucibles for the fusions. Both the can and the cooled melt are dissolved in nitric acid. Fusion tests were conducted on three different cans of incinerator ash and on one can of centrifuge sludge. The series of tests demonstrated that a caustic-peroxide fusion treatment can yield 95 percent or greater recovery of plutonium from these waste solids. In most cases, quantitative recovery of the plutonium can probably be achieved by recycling the residual solids obtained in aqueous dissolution of the cooled fusion mixture. Tests with some of the incinerator ash and with the centrifuge sludge resulted in gelatinous precipitates which were difficult to separate from the nitric acid dissolver solutions. These gelatinous precipitates present what is probably the major problem to be overcome in the use of this Pu recovery method. Techniques need to be examined for making these residual solids less difficult to separate from the dissolver solution. (U.S.)

Sugarcane bagasse ash: new filler to natural rubber composite

Directory of Open Access Journals (Sweden)

Renivaldo José dos Santos

2014-12-01

Full Text Available Waste recycling has been the subject of numerous scientific researches regarding the environmental care. This paper reports the redirecting of sugarcane bagasse ash (SBA as new filler to natural rubber (NR/SBA. The NR/SBA composites were prepared using an opened cylinder mixer to incorporate the vulcanization agents and different proportions of residue (SBA. The ash contains about 70-90% of inorganic compounds, with silica (SiO2 being the main compound. The SBA incorporation improved the mechanical properties of the vulcanized rubber. Based on these results, a new use is proposed for the agro-industry organic waste to be implemented in the rubber vulcanization process, aimed at improving the rubber physical properties as well as decreasing the prices of natural rubber composites.

Effects of thermal processing on the enzyme-linked immunosorbent assay (ELISA) detection of milk residues in a model food matrix.

Science.gov (United States)

Downs, Melanie L; Taylor, Steve L

2010-09-22

Food products and ingredients are frequently tested for the presence of undeclared allergenic food residues (including milk) using commercial enzyme-linked immunosorbent assays (ELISAs). However, little is understood about the efficacy of these kits with thermally processed foods. This study evaluated the performance of three milk ELISA kits with a model food processed by several methods. A model food (pastry dough squares) was spiked with nonfat dry milk at several concentrations. The pastry squares were processed by boiling (100 °C for 2 min), baking (190 °C for 30 min), frying (190 °C for 2 min), and retorting (121 °C for 20 min with 17 psi overpressure). Samples were analyzed with three commercial ELISA kits: Neogen Veratox Total Milk, ELISA Systems β-lactoglobulin, and ELISA Systems casein. The detection of milk residues depended upon the type of processing applied to the food and the specific milk analyte targeted by the ELISA kit. Poor recoveries were obtained in all processed samples (2-10% of expected values) using the β-lactoglobulin kit. Better recoveries were obtained in boiled samples (44 and 59%, respectively) using the total milk and casein kits. However, these kits performed poorly with baked (9 and 21%) and fried (7 and 18%) samples. Moderate recoveries were observed in retorted samples (23 and 28%). The decreased detection in processed samples is likely due to protein modifications, including aggregation and Maillard reactions, which affect the solubility and immunoreactivity of the antigens detected by the ELISA methods. The observed decreases in ELISA detection of milk are dramatic enough to affect risk-assessment decisions. However, a lower detection of milk residues does not necessarily indicate decreased allergenicity. These ELISA kits are not acceptable for all applications, and users should understand the strengths and limitations of each method.

Inorganic contaminants attenuation in acid mine drainage by fly ash and fly ash-ordinary Portland cement (OPC) blends : column experiments

International Nuclear Information System (INIS)

Gitari, W.M.; Petrik, L.F.; Etchebers, O.; Key, D.L.; Okujeni, C.

2010-01-01

The infiltration of acid mine drainage (AMD) material into mine voids is one of the environmental impacts of underground coal mining. In this study, the mitigation of AMD in a mine void was simulated in laboratory conditions. Various mixtures of fly ash, solid residues, and Portland cement were added to packed columns over a 6-month period. The fly ash additions generated near-neutral to alkaline pH levels, which in turn induced precipitation, co-precipitation, and adsorption contaminant attenuation mechanisms. A modelling study demonstrated that the precipitation of ferrihydrite, Al-hydroxides, Al-oxyhydroxysulphates, gypsum, ettringite, manganite, and rhodochrosite lowered contaminant levels. Results of the study indicated that the pH regime and acidity level of the AMD strongly influenced both the leaching of the toxic trace elements as well as the attenuation of the AMD. 3 refs., 2 figs.

Wet-Treated MSWI Fly Ash Used as Supplementary Cementitious Material

Directory of Open Access Journals (Sweden)

Martin Keppert

2015-01-01

Full Text Available Municipal solid waste incineration (MSWI is a common technique in treatment of domestic waste. This technique annually produces approximately 25 Mt solid residues (i.e., bottom and fly ash worldwide which is also a major issue in current research. In this research we are concerned with reusing the fly ash (FA as supplementary cementitious material (SCM in concrete. Such application solves the problem with heavy metal immobilization as well. To remove the high content of undesired soluble salts, number of washing treatments has been applied. Chemical composition of FA has been examined before and after treatments. The impact of cement substitution by FA in concrete was evaluated by measurement of its compressive strength and durability.

Increased sensitivity in thick-target particle induced X-ray emission analyses using dry ashing for preconcentration

International Nuclear Information System (INIS)

Lill, J.-O.; Harju, L.; Saarela, K.-E.; Lindroos, A.; Heselius, S.-J.

1999-01-01

The sensitivity in thick-target particle induced X-ray emission (PIXE) analyses of biological materials can be enhanced by dry ashing. The gain depends mainly on the mass reduction factor and the composition of the residual ash. The enhancement factor was 7 for the certified reference material Pine Needles and the limits of detection (LODs) were below 0.2 μg/g for Zn, Cu, Rb and Sr. When ashing biological materials with low ash contents such as wood of pine or spruce (0.3% of dry weight) and honey (0.1% of wet weight) the gain was far greater. The LODs for these materials were 30 ng/g for wood and below 10 ng/g for honey. In addition, the ashed samples were more homogenous and more resistant to changes during the irradiation than the original biological samples. (Copyright (c) 1999 Elsevier Science B.V., Amsterdam. All rights reserved.)

Production of low ash coal by thermal extraction with N-methyl-2-pyrrolidinone

Energy Technology Data Exchange (ETDEWEB)

Do Kim, S.; Woo, K.J.; Jeong, S.K.; Rhim, Y.J.; Lee, S.H. [Korean Institute for Energy Research, Taejon (Republic of Korea). Clean Coal Technological Research Center

2008-07-15

Present study was conducted for the purpose of producing low ash coal from LRC (low rank coals) such as lignite and sub-bituminous coal through thermal extraction using polar solvent. Extraction from bituminous coal was also investigated for comparison. NMP as a polar solvent was used. The ratio of coal to solvent was adjusted as 1:10. Experimental conditions were established which include the extraction temperature of 200-430{sup o}C, initial applied pressure of 1-20 bar and extraction time of 0.5-2 hr were used. Extraction yield and ash content of extracted and residual coal were measured. The extraction yield increased with the increase of extraction temperature, and the ash content of extracted coal decreased below 0.4% at 400{sup o}C from the raw coal samples that have the ash contents of 4-6%. According to the analysis of experiments results, fixed carbon and calorific value increased, and H/C and O/C decreased.

Release of microspherolites and metals extraction from energetical fly ashes by Bacillus isolates

Directory of Open Access Journals (Sweden)

Štyriaková Iveta

2000-09-01

Full Text Available The amorphous secondary silicate mineral components formed in the process of coal combustion dominate in the composition of energy fly-ash. Depending on the composition of coal concentrate, this secondary raw material source also contains the industrially interesting components, e.g. titanium (eventually iron and aluminium and can be considered as a non-metallic material suitable for the construction industry.The main secondary mineral components of the energy fly-ash formed during the coal combustion were studied using SEM (scanning electronic microscope. They can be divided into four groups:1. Amorphous spherical alumocilicate particles in allotriomorphic aluminosilicate grains – they represent a main mineral component of fly-ash, which is formed from the accompanying rocks of coal containing silicate minerals,2. Quartz – which formed a substantial component of accompanying rocks of coal or accompanying accessory mineral of coal together with kaolinite and mica, was transformed into tridymite at the temperature exceeding 870°C and into cristobalite at the temperature exceeding 1470°C. The spherical particles are products of reaction between cristobalite and aluminosilicate, which is a frequent phenomenon occurring during the formation of volcanic rocks. These particles form together a main amorphous phase of fly-ash.3. Mullite – represents a secondary component of fly-ash, which is formed from accompanying clay minerals of coal (kaolinite, mica together with cristobalite under the effect of temperature exceeding 1150°C,4. Non-combusted residue – consists of organic substance, represents a non-combusted ratio of coal as a secondary component of fly-ash.Heterotrophic bacteria of Bacillus genus are capable to remove 66 % of titanium and 33 % of iron from non-deposited fly-ash from Opatovice after 35 days of leaching of samples. The content of solid phase in fly-ash influences the extraction of elements, mainly iron and titatnium, because

Energetical fly ashes – separation and utilization of metallic valuable components

Directory of Open Access Journals (Sweden)

Michalíková Františka

2000-12-01

Full Text Available In the contribution, methods of separating metals – Fe, Al, Ge from energetic wastes – fly ashes are presented along with further possibilities of utilization of particular valuable components for industrial purposes.In the contribution, properties of energetic wastes are presented influencing the contents, separability, and utilizability of metal-bearing valuable components. From among physical properties these are grain size distribution and surface area. Chemical properties are characterized by elements contained in combusted coal whose content after combustion is increased 2 to 4 times, depending on the content of ash and combustible matters in original coal. Mineralogical properties of energetic wastes are determined by the combustion process conditions in the course of which mineral novelties are produced in concentrations suitable for separation.In the contribution, methods of separation and utilization of metals such as Fe, Al, Ge are described. From literature information on the processing of Fe component, as well as from results of experiments made at the Department of Mineral Processing and Environmental Protection, Technical University of Kosice follows that the highest concentration and mass yield of the component can be obtained from black coal fly ashes produced in smelting boilers. The content of Al in Slovak energetic wastes is lower than the 30 % Al2O3 limit that conditions an economic technological processing. Only in the case of black coal fly ash from TEKO Kosice and EVO Vojany was the Al2O3 content of 32.93 %. Therefore, in an indirect way – by separating the residues of uncombusted coal and magnetite Fe – the content of Al in fly ash was increased.For Ge, a principle of selective sizing has been utilized.A complex utilization of energetic wastes, that is the separation of metallic components, elimination of particular metals and the subsequent treatment of nonmetallic residue, should be an effective solution in various

Structural and Mechanical Characterization of Sustainable Composites Based on Recycled and Stabilized Fly Ash

Directory of Open Access Journals (Sweden)

Stefano Besco

2014-08-01

Full Text Available This paper reports the results on the use of an innovative inert, based on stabilized fly ash from municipal solid waste incineration as a filler for polypropylene. The starting material, which contains large quantities of leachable Pb and Zn, was stabilized by means of an innovative process using rice husk ash as a waste silica source, together with other fly ashes, such as coal fly ash and flue gas desulfurization residues. The use of all waste materials to obtain a new filler makes the proposed technology extremely sustainable and competitive. The new composites, obtained by using the stabilized material as a filler for polypropylene, were characterized and their mechanical properties were also investigated. A comparison with a traditional polypropylene and calcium carbonate based compound was also done. This research activity was realized in the frame of the COSMOS-RICE project, financed by the EU Commission.

Biomass ash utilization

Energy Technology Data Exchange (ETDEWEB)

Bristol, D.R.; Noel, D.J.; O`Brien, B. [HYDRA-CO Operations, Inc., Syracuse, NY (United States); Parker, B. [US Energy Corp., Fort Fairfield, ME (United States)

1993-12-31

This paper demonstrates that with careful analysis of ash from multiple biomass and waste wood fired power plants that most of the ash can serve a useful purpose. Some applications require higher levels of consistency than others. Examples of ash spreading for agricultural purposes as a lime supplement for soil enhancement in Maine and North Carolina, as well as a roadbase material in Maine are discussed. Use of ash as a horticultural additive is explored, as well as in composting as a filtering media and as cover material for landfills. The ash utilization is evaluated in a framework of environmental responsibility, regulations, handling and cost. Depending on the chemical and physical properties of the biomass derived fly ash and bottom ash, it can be used in one or more applications. Developing a program that utilizes ash produced in biomass facilities is environmentally and socially sound and can be financially attractive.

Soil application of ash produced by low-temperature fluidized bed gasification: effects on soil nutrient dynamics and crop response

DEFF Research Database (Denmark)

Müller-Stöver, Dorette Sophie; Ahrenfeldt, Jesper; Holm, Jens Kai

2012-01-01

not significantly altered after ash application. SA was generally able to increase the levels of Olsen-P and of the ammonium acetate/acetic acid-extractable K in soil as well as to improve the yield of barley and maize, whereas faba bean did not react positively to ash amendment. CP did not show beneficial effects......Recycling of residual products of bioenergy conversion processes is important for adding value to the technologies and as a potential beneficial soil fertility amendment. In this study, two different ash materials originating from low temperature circulating fluidized bed (LT-CFB) gasification...... of either wheat straw (SA) or residue fibers mainly from citrus peels (CP) were tested regarding their potential to be used as fertilizer on agricultural soils. A soil incubation study, a greenhouse experiment with barley and faba bean, and an accompanying outdoor experiment with maize were carried out...

Environmental assessment of remedial action at the inactive uraniferous lignite ashing sites at Belfield and Bowman, North Dakota

International Nuclear Information System (INIS)

1993-09-01

The Uranium Mill Tailings Radiation Control Act (UMTRCA) of 1978 authorized the US Department of Energy (DOE) to perform remedial actions at Belfield and Bowman inactive lignite ashing sites in southwestern North Dakota to reduce the potential public health impacts from the residual radioactivity remaining at the sites. The US Environmental Protection Agency (EPA) promulgated standards (40 CFR 192) that contain measures to control the residual radioactive materials and other contaminated materials, and proposed standards to protect the groundwater from further degradation. Remedial action at the Belfield and Bowman sites must be performed in accordance with these standards and with the concurrence of the US Nuclear Regulatory Commission (NRC) and the state of North Dakota. The Belfield and Bowman designated sites were used by Union Carbide and Kerr-McGee, respectively, to process uraniferous lignite in the 1960s. Uranium-rich ash from rotary kiln processing of the lignite was loaded into rail cars and transported to uranium mills in Rifle, Colorado, and Ambrosia Lake, New Mexico, respectively. As a result of the ashing process, there is a total of 158,400 cubic yards (yd 3 ) [121,100 cubic meters (m 3 )] of radioactive ash-contaminated soils at the two sites. Windblown ash-contaminated soil covers an additional 21 acres (8.5 ha) around the site, which includes grazing land, wetlands, and a wooded habitat

Gehlenite and anorthite formation from fluid fly ash

Science.gov (United States)

Perná, Ivana; Šupová, Monika; Hanzlíček, Tomáš

2018-04-01

Fluid fly ash could be considered a waste, but, when well treated, it may also become a useful secondary source material. Its rather high content of calcium-containing phases along with thermally treated alumino-silicate residues resulting from coal combustion can lead to the formation of a stable system with newly formatted phases. The high temperature destroys the clay lattice and activates a new configuration of aluminum ions, changing their coordination to oxygen. The effect is accompanied by changes in charge in the surroundings, which are compensated for by calcium ions. The higher the temperature of the fluid ash treatment, the more pronounced the appearance of gehlenite and anorthite in the final mass. Both are natural materials and, together with mullite and anhydrite, they could ensure safety and protection even if exposed to open fire of up to 1150 °C.

Removal of chloride from fly ash produced in hazardous waste incineration by leaching and displacement washing in a vertical filter press.

Science.gov (United States)

Kinnarinen, Teemu; Huhtanen, Mikko; Penttilä, Mika; Häkkinen, Antti

2013-02-01

Fly ash is generated in large quantities by waste incineration processes. Chloride is commonly present in the fly ash produced by the incineration of hazardous materials, such as polyvinylchloride plastic. Major difficulties related to the disposal and handling of fly ash include the high concentration of easily leachable chlorides, heavy metals and toxic compounds. In order to avoid adverse environmental effects from the disposal of fly ash, the content of soluble chlorides must be reduced. One of the most effective options for chloride removal is leaching and displacement washing in a filter press. The primary aim of this study was to obtain efficient removal of chloride from fly ash by utilizing a leaching and displacement washing process, carried out in a filter press. The secondary objective was to obtain high filtration capacities and low filter cake moisture contents. The slurry was prepared by mixing fly ash with water at an ash:water ratio of 1:2 and filtered to separate the solids from the liquid. After solid-liquid separation, most of the dissolved residual chloride was removed from the filter cake by washing the cake with fresh water in the second stage of separation. It was possible to remove up to 98% of the total chloride and to obtain sufficient filtration capacities. The residual moisture content of the filter cakes varied from 22 to 35 wt%, which meant that the cakes could be disposed of in landfill, or possibly utilized as a construction material.

Temporal evolution of wildfire ash and its implications for water pollution

Science.gov (United States)

Santin, Cristina; Doerr, Stefan H.; Otero, Xose L.; Chafer, Chris J.

2015-04-01

Ash, the burnt residue generated from combustion of vegetation, litter and surface soil, covers the ground after every wildfire. The effects of wildfire ash on the post-fire landscape are many and very diverse. It is a source of nutrients and can, therefore, help the recovery of vegetation after fire. Furthermore, in its initial state, the ash layer on the ground can protect the bare soil from rain splash erosion and can act as an adsorbent layer, preventing or delaying post-fire water erosion by runoff. However, when the adsorbent capability of the ash layer is exceeded, this highly erodible material can be transported into the hydrological network and be a major contributor to water contamination. Most previous studies on post-fire erosion and water contamination have focused on soil erosion and associated sediment transfer and overlooked the ash component or, when considered, ash has been included as an unidentified part of the eroded sediment. One of the reasons for overlooking this key post-fire component is the difficulty of ash sampling before it is lost by wind or water erosion or altered by aging on-site. Here we compare the water contamination potential of ash obtained from two fires in the dry eucalyptus forest environment of the Sydney tablelands, Australia: i) 'aged ash' produced during the severe Balmoral wildfire and sampled two months after the event (Jan. 2014) and ii) 'fresh ash' sampled immediately after a high-intensity experimental fire in the same region (Sept. 2014). At the time of sampling, neither of the ash types had been affected by water erosion, however, the aged ash had been subjected to rainfall events and, potentially, to wind erosion during the two months of exposure. Vegetation type, fuel loads and fire severity, determined using remote sensing and on-site observations, were comparable between both areas sampled. Ash physicochemical properties differed, with 'fresh ash' having higher pH and EC values and higher concentration of

Fluorination of incinerator ash by hydrofluorination or ammonium bifluoride fusion for plutonium recovery

Energy Technology Data Exchange (ETDEWEB)

Fink, S.D.; Gray, J.H.; Kent, S.J.; Apgar, S.A.

1989-01-01

Incinerator ash containing small quantities of plutonium has been accumulating across the defense complex for many years. Although the total Pu inventory is small, the ash is a nondiscardable residue which presents storage and accountability difficulties. The work discussed here is the result of a joint exploratory effort between members of Savannah River Laboratory and Los Alamos National Laboratory to compare two proposed pyrochemical pretreatments of incinerator ash prior to aqueous processing. These experiments attempted to determine the relative effectiveness of hydrofluorination and ammonium bifluoride fusion as head-end operations for a two step aqueous recovery method. The two pretreatments are being considered as possible second generation enhancements for the New Special Recovery Facility nearing operation at Savannah River Plant. Experimental results and potential engineering concerns are discussed. 3 figs.

Development of novel ash hybrids to introgress resistance to emerald ash borer into north American ash species

Science.gov (United States)

Jennifer L. Koch; David W. Carey; Mary E. Mason

2008-01-01

Currently, there is no evidence that any of the native North American ash species have any resistance to the emerald ash borer (EAB). This means that the entire ash resource of the eastern United States and Canada is at risk of loss due to EAB. In contrast, outbreaks of EAB in Asian ash species are rare and appear to be isolated responses to stress (Bauer et al. 2005,...

Physical-chemical characterization of bovine bone ash for evaluating its potential agricultural use

Directory of Open Access Journals (Sweden)

Eduardo Pacca Luna Mattar

2014-03-01

Full Text Available The manufacturing of bovine bone ash is a low cost and easy production process which can be adopted for making good use of animal residues, in locations without infrastructure, such as the family production units. This study aimed at describing the manufacturing process of bone ash and characterizing the physical and chemical parameters of the resulting material for organic fertilization. The experiment was performed with three replications, being evaluated the bovine bone ash manufacturing process yield, as well as its density, water retention capacity, pH of the resulting material after burning and contents of total calcium, calcium soluble in water, total phosphorus and phosphorus soluble in citric acid and in ammonium citrate. The process resulted in an average yield of 24.4% and the bovine bone ash presented 33.07% of total calcium, 15.6% of total phosphorus, 10.4% of phosphorus soluble in citric acid, pH of 9.94, density of 0.89 g cm-3 and water retention capacity of 73.3%. The bovine bone ash showed promising characteristics, with potential for being used as source of phosphorus and calcium in the organic fertilization process.

Method of recovering oils, etc. , from bituminous shales

Energy Technology Data Exchange (ETDEWEB)

Bergh, S V

1921-05-23

In the low-temperature distillation of bituminous shales or similar bituminous materials with high ash content for recovery of oil etc., steam or inert gases are introduced from outside through gas taps arranged in a circle in the retort. By the method used steam is introduced simultaneously in levels higher and lower than the one in which the gaseous and vaporized products are removed from the shale material and in such a manner that the zone of oil formation chiefly will be between the two places mentioned where vapors or steam are introduced into the retort. The patent has one additional claim.

Time course of pulmonary burden in mice exposed to residual oil fly ash

Directory of Open Access Journals (Sweden)

Giovanna Marcella Cavalcante Carvalho

2014-09-01

Full Text Available Residual oil fly ash (ROFA is a common pollutant in areas where oil is burned. This particulate matter with a broad distribution of particle diameters can be inhaled by human beings and putatively damage their respiratory system. Although some studies deal with cultured cells, animals, and even epidemiological issues, so far a comprehensive analysis of respiratory outcomes as a function of the time elapsed after exposure to a low dose of ROFA is wanted. Thus, we aimed to investigate the time course of mechanical, histological, and inflammatory lung changes, as well as neutrophils in the blood, in mice exposed to ROFA until 5 days after exposure. BALB/c mice (25±5 g were randomly divided into 7 groups and intranasally instilled with either 10 µL of sterile saline solution (0.9% NaCl, CTRL or ROFA (0.2 µg in 10 L of saline solution. Pulmonary mechanics, histology (normal and collapsed alveoli, mononuclear and polymorphonuclear cells, and ultrastructure, neutrophils (in blood and bronchoalveolar lavage fluid were determined at 6 h in CTRL and at 6, 24, 48, 72, 96 and 120 h after ROFA exposure. ROFA contained metal elements, especially iron, polycyclic aromatic hydrocarbons, and organochlorines. Lung resistive pressure augmented early (6 h in the course of lung injury and other mechanical, histological and inflammatory parameters increased at 24 h, returning to control values at 120 h. Blood neutrophilia was present only at 24 and 48 h after exposure. Swelling of endothelial cells with adherent neutrophils was detected after ROFA instillation. No neutrophils were present in the lavage fluid. In conclusion, the exposure to ROFA, even in low doses, induced early changes in pulmonary mechanics, lung histology and accumulation of neutrophils in blood of mice that lasted for four days and disappeared spontaneously.

Time course of pulmonary burden in mice exposed to residual oil fly ash.

Science.gov (United States)

Carvalho, Giovanna Marcella Cavalcante; Nagato, Lilian Katiê da Silva; Fagundes, Sheila da Silva; Dos Santos, Flávia Brandão; Calheiros, Andrea Surrage; Malm, Olaf; Bozza, Patricia Torres; Saldiva, Paulo Hilário N; Faffe, Débora Souza; Rocco, Patricia Rieken Macedo; Zin, Walter Araujo

2014-01-01

Residual oil fly ash (ROFA) is a common pollutant in areas where oil is burned. This particulate matter (PM) with a broad distribution of particle diameters can be inhaled by human beings and putatively damage their respiratory system. Although some studies deal with cultured cells, animals, and even epidemiological issues, so far a comprehensive analysis of respiratory outcomes as a function of the time elapsed after exposure to a low dose of ROFA is wanted. Thus, we aimed to investigate the time course of mechanical, histological, and inflammatory lung changes, as well as neutrophils in the blood, in mice exposed to ROFA until 5 days after exposure. BALB/c mice (25 ± 5 g) were randomly divided into 7 groups and intranasally instilled with either 10 μL of sterile saline solution (0.9% NaCl, CTRL) or ROFA (0.2 μg in 10 μL of saline solution). Pulmonary mechanics, histology (normal and collapsed alveoli, mononuclear and polymorphonuclear cells, and ultrastructure), neutrophils (in blood and bronchoalveolar lavage fluid) were determined at 6 h in CTRL and at 6, 24, 48, 72, 96, and 120 h after ROFA exposure. ROFA contained metal elements, especially iron, polycyclic aromatic hydrocarbons (PAHs), and organochlorines. Lung resistive pressure augmented early (6 h) in the course of lung injury and other mechanical, histological and inflammatory parameters increased at 24 h, returning to control values at 120 h. Blood neutrophilia was present only at 24 and 48 h after exposure. Swelling of endothelial cells with adherent neutrophils was detected after ROFA instillation. No neutrophils were present in the lavage fluid. In conclusion, the exposure to ROFA, even in low doses, induced early changes in pulmonary mechanics, lung histology and accumulation of neutrophils in blood of mice that lasted for 4 days and disappeared spontaneously.

Silica from Ash

Indian Academy of Sciences (India)

management, polymer composites and chemical process design. Figure 1 Difference in color of the ash ... The selection of ash is important as the quality of ash determines the total amount as well as quality of silica recoverable Ash which has undergone maximum extent of combustion is highly desirable as it contains ...

Evaluation of wood residues from Crete as alternative fuels

Energy Technology Data Exchange (ETDEWEB)

Vamvuka, D. [Department of Mineral Resources Engineering, Technical University of Crete (Greece); Bandelis, G. [Professional School of Chania, EPAS Chania (Greece)

2010-07-01

Olive and citrus prunings, the main agricultural residues of Crete, are considered to be of premium importance for local energy production, substituting a large part of conventional fuels. The thermal behaviour of these fuels during combustion was studied by thermogravimetry, at non-isothermal heating conditions. Fly ashes were collected from tests in a lab-scale fluidized bed facility. The effect of the inorganic constituents of the fuels on slagging/fouling and agglomeration propensities, as well as environmental pollution was examined. Kinetic models were developed and reaction rates were determined. The agroresidues studied were characterized as good quality fuels, having high volatile and low ash and sulphur contents. Their ash was rich in Ca, Si, K and P minerals. However, fly ashes were poorer in alkali compounds, implying lower deposition and corrosion problems in boilers. The environmental impact of heavy metals is negligible. The thermochemical reactivity of the two fuels in air was very similar. A power low model fitted the experimental results accurately.

Effect of γ-irradiation on commercial polypropylene based mono and multi-layered retortable food packaging materials

Science.gov (United States)

George, Johnsy; Kumar, R.; Sajeevkumar, V. A.; Sabapathy, S. N.; Vaijapurkar, S. G.; Kumar, D.; Kchawahha, A.; Bawa, A. S.

2007-07-01

Irradiation processing of food in the prepackaged form may affect chemical and physical properties of the plastic packaging materials. The effect of γ-irradiation doses (2.5-10.0 kGy) on polypropylene (PP)-based retortable food packaging materials, were investigated using Fourier transform infrared (FTIR) spectroscopic analysis, which revealed the changes happening to these materials after irradiation. The mechanical properties decreased with irradiation while oxygen transmission rate (OTR) was not affected significantly. Colour measurement indicated that Nylon 6 containing multilayer films became yellowish after irradiation. Thermal characterization revealed the changes in percentage crystallinity.

Effect of γ-irradiation on commercial polypropylene based mono and multi-layered retortable food packaging materials

International Nuclear Information System (INIS)

George, Johnsy; Kumar, R.; Sajeevkumar, V.A.; Sabapathy, S.N.; Vaijapurkar, S.G.; Kumar, D.; Kchawahha, A.; Bawa, A.S.

2007-01-01

Irradiation processing of food in the prepackaged form may affect chemical and physical properties of the plastic packaging materials. The effect of γ-irradiation doses (2.5-10.0 kGy) on polypropylene (PP)-based retortable food packaging materials, were investigated using Fourier transform infrared (FTIR) spectroscopic analysis, which revealed the changes happening to these materials after irradiation. The mechanical properties decreased with irradiation while oxygen transmission rate (OTR) was not affected significantly. Colour measurement indicated that Nylon 6 containing multilayer films became yellowish after irradiation. Thermal characterization revealed the changes in percentage crystallinity

Effect of {gamma}-irradiation on commercial polypropylene based mono and multi-layered retortable food packaging materials

Energy Technology Data Exchange (ETDEWEB)

George, Johnsy [Defence Food Research Laboratory, Siddarthanagar, Mysore, Karnataka 570011 (India)]. E-mail: g.johnsy@gmail.com; Kumar, R. [Defence Food Research Laboratory, Siddarthanagar, Mysore, Karnataka 570011 (India); Sajeevkumar, V.A. [Defence Food Research Laboratory, Siddarthanagar, Mysore, Karnataka 570011 (India); Sabapathy, S.N. [Defence Food Research Laboratory, Siddarthanagar, Mysore, Karnataka 570011 (India); Vaijapurkar, S.G. [Defence Laboratory, Ratanada Palace, Jodhpur, Rajastan 342011 (India); Kumar, D. [Defence Laboratory, Ratanada Palace, Jodhpur, Rajastan 342011 (India); Kchawahha, A. [Defence Laboratory, Ratanada Palace, Jodhpur, Rajastan 342011 (India); Bawa, A.S. [Defence Food Research Laboratory, Siddarthanagar, Mysore, Karnataka 570011 (India)

2007-07-15

Irradiation processing of food in the prepackaged form may affect chemical and physical properties of the plastic packaging materials. The effect of {gamma}-irradiation doses (2.5-10.0 kGy) on polypropylene (PP)-based retortable food packaging materials, were investigated using Fourier transform infrared (FTIR) spectroscopic analysis, which revealed the changes happening to these materials after irradiation. The mechanical properties decreased with irradiation while oxygen transmission rate (OTR) was not affected significantly. Colour measurement indicated that Nylon 6 containing multilayer films became yellowish after irradiation. Thermal characterization revealed the changes in percentage crystallinity.

Combustion of mediterranean agro-forest biomasses in small and medium scale pellet boilers: strategies for minimizing ash fusion and slagging

Energy Technology Data Exchange (ETDEWEB)

Vega-Nieva, Daniel J.; Dopazo, Raquel; Ortiz, Luis [Forest Engineering Univ. School. Univ. of Vigo, Pontevedra (Spain)], e-mail: DanielJVN@gmail.com

2012-11-01

The slagging and fouling risk remain as important barriers that are currently limiting the use of various agricultural residues and potential energy crops feedstocks (e.g. [1-3]), which remain largely unutilized, particularly in Mediterranean countries. In this oral communication, the main results from the VI Framework European Project Domoheat on the combustion of mediterranean biomasses and its mixtures on small and medium size domestic pellet boilers, are presented, together with the goals of the ongoing VII Framework European Project AshMelT focusing on the definition of objective criteria and tests for ash slagging in domestic pellet boilers. The utilization of ash slagging indices based on ash composition and the definition of biomass mixtures based on such ash indices are presented as potentially useful tools for minimizing the occurrence of ash fusion and slagging during combustion.

Evaluation of metals, metalloids, and ash mixture toxicity using sediment toxicity testing.

Science.gov (United States)

Stojak, Amber; Bonnevie, Nancy L; Jones, Daniel S

2015-01-01

In December 2008, a release of 4.1 million m(3) of coal ash from the Tennessee Valley Authority Kingston Fossil Plant occurred. Ash washed into the Emory River and migrated downstream into the Clinch and Tennessee Rivers. A Baseline Ecological Risk Assessment evaluated risks to ecological receptors from ash in the river system post-dredging. This article describes the approach used and results from sediment toxicity tests, discussing any causal relationships between ash, metals, and toxicity. Literature is limited in the realm of aquatic coal combustion residue (CCR) exposures and the potential magnitude of effects on benthic invertebrates. Sediment samples along a spectrum of ash content were used in a tiered toxicity testing approach and included a combination of 10 day sediment toxicity acute tests and longer-term, partial life cycle "definitive" tests with 2 species (Hyalella azteca and Chironomus dilutus). Arsenic, and to a lesser extent Se, in the ash was the most likely toxicant causing observed effects in the laboratory toxicity tests. Sites in the Emory River with the greatest statistical and biologically significant effects had As concentrations in sediments twice the probable effects concentration of 33 mg/kg. These sites contained greater than 50% ash. Sites with less than approximately 50% ash in sediments exhibited fewer significant toxic responses relative to the reference sediment in the laboratory. The results discussed here present useful evidence of only limited effects occurring from a worst-case exposure pathway. These results provided a valuable line of evidence for the overall assessment of risks to benthic invertebrates and to other ecological receptors, and were crucial to risk management and development of project remediation goals. © 2014 SETAC.

Wildland fire ash: Production, composition and eco-hydro-geomorphic effects

Science.gov (United States)

Bodi, Merche B.; Martin, Deborah; Balfour, Victoria N.; Santin, Cristina; Doerr, Stefan H.; Pereira, Paulo; Cerda, Artemi; Mataix-Solera, Jorge

2014-01-01

Fire transforms fuels (i.e. biomass, necromass, soil organic matter) into materials with different chemical and physical properties. One of these materials is ash, which is the particulate residue remaining or deposited on the ground that consists of mineral materials and charred organic components. The quantity and characteristics of ash produced during a wildland fire depend mainly on (1) the total burned fuel (i.e. fuel load), (2) fuel type and (3) its combustion completeness. For a given fuel load and type, a higher combustion completeness will reduce the ash organic carbon content, increasing the relative mineral content, and hence reducing total mass of ash produced. The homogeneity and thickness of the ash layer can vary substantially in space and time and reported average thicknesses range from close to 0 to 50 mm. Ash is a highly mobile material that, after its deposition, may be incorporated into the soil profile, redistributed or removed from a burned site within days or weeks by wind and water erosion to surface depressions, footslopes, streams, lakes, reservoirs and, potentially, into marine deposits.Research on the composition, properties and effects of ash on the burned ecosystem has been conducted on material collected in the field after wildland and prescribed fires as well as on material produced in the laboratory. At low combustion completeness (typically T  450 °C), most organic carbon is volatized and the remaining mineral ash has elevated pH when in solution. It is composed mainly of calcium, magnesium, sodium, potassium, silicon and phosphorous in the form of inorganic carbonates, whereas at T > 580 °C the most common forms are oxides. Ash produced under lower combustion completeness is usually darker, coarser, and less dense and has a higher saturated hydraulic conductivity than ash with higher combustion completeness, although physical reactions with CO2 and when moistened produce further changes in ash characteristics.As a new

Leaching of Antimony (Sb)from Municipal Solid Waste Incineration (MSWI) Residues

Energy Technology Data Exchange (ETDEWEB)

Herrmann, Inga

2004-07-01

The mobility of antimony (Sb) in municipal solid waste incineration (MSWI) residues often exceeds the limit values stipulated by the European Union. As an ash treatment by washing is conceivable, this work investigated the Sb release from Swedish bottom ash and fly ash when mixed with water. The leaching experiments revealed the factors significantly (a = 0.05) affecting Sb release from the ashes. The following factors were investigated: Liquid to solid ratio (L/S), time, pH, carbonation (treatment with CO{sub 2}), ultrasonics and temperature. The data were evaluated using multiple linear regression (MLR). The impact of the factors could be quantified. The maximum Sb release calculated was 13 mg/kg DM for bottom ash and 51 mg/kg DM for fly ash. The derived models explained the observed data well. Nevertheless, the calculated values were subject to a high uncertainty. For bottom ash, a lowering of the Sb total content of approximately 22% could be achieved. If this also involves a sufficient lowering of the Sb mobility to meet EU limit values could not yet be assessed. Chemical equilibrium calculations were performed to explain the empirical results. However, no solid phases controlling Sb release from the ashes could be identified.

Stabilization of ash from combustion of MSW in a fluidised bed boiler

Energy Technology Data Exchange (ETDEWEB)

Steenari, Britt-Marie; Wilewska, Magda [Chalmers Univ. of Technology, Goeteborg (Sweden). Dept. of Environmental Inorganic Chemistry

2004-06-01

Due to restrictions against the land filling of combustible waste and directives from authorities that favour energy recovery from the waste, combustion of household waste is becoming more common. Even though combustion of MSW reduces the volume of waste to be handled by approximately 90%, it produces ash residues containing most of the metals present in the original fuel and a number of other species carried through the boiler or formed during combustion. The residues can be divided into three categories: 1. Stable, inert ash that can be utilised in, for example, construction applications 2. Ash that is stable enough to be land filled as nonhazardous waste 3. Ash that contains large amounts of soluble components and potentially toxic metal species. The regulations considering leaching of ash components set limits for the release of soluble salts and toxic metals. Some fly ashes show low leachability for metals but gives a salt release that is too close to the limit for total dissolved solids. Since fly ash from FBC boilers represent the largest volume of ash from these boilers there is a need for a simple and cheap treatment method that reduces the amount of soluble salts, i.e. NaCl, KCl etc, in the ash. After stabilisation, the ash is supposed to go into a more stable category. The aim of this project has been to investigate the applicability of a method to wash such an ash with water. The work included laboratory studies of the ash properties, the water washing process, filtration properties of the ash slurry and also tests of the method in pilot scale at a full scale boiler. This work has been concentrated towards the investigation of cyclone ash from a bubbling fluidised bed boiler in Lidkoeping fired with 100% household waste. Elemental composition of ash samples before and after washing/filtration was determined by AAS or ICP after a suitable dissolution of the sample. The mineralogy of ash samples was analysed using X-ray powder diffractometry. This method

Sorption behaviour of some radioactive isotopes on treated fly ash. Vol. 3

Energy Technology Data Exchange (ETDEWEB)

Abdel Raouf, M W; El-Dessouky, M I; Aly, H F [Hot Laboratories Center, Atomic Energy Authority, Cairo, (Egypt)

1996-03-01

Fly ash is obtained as a by-product from burning mazoute (high molecular weight hydrocarbon) at Northern Cairo Electric Power Generator, was ordinarily disposed in land fill. The carbonaceous material of fly ash was investigated as a possible sorbent for some fission products radionuclides: Cs{sup 134}, Co{sup 60}, and Eu{sup 142+154} at room temperature. The original fly ash was prepared for adsorption studies by sieving to different particle sizes (fractions), and repeated washing by tap water to neutral PH. Some fractions were further treated (after neutralization) by dilute HCl or ethyl alcohol and other fractions were heated at 200, 500, and 800 degree C. The results obtained from sorption on treated fly ash revealed that the percentage uptake (%U) was in accordance with the valency of the cation used: Eu{sup 3+}>Co{sup 2+}>>Cs{sup +} at medium hydrogen ion concentrations. The heated samples at different temperatures showed that % U obeyed the order: 800 degree C >200 degree C. Comparative studies were conducted with pyrolysis residue of domestic waste showed analogous trend in sorption studies. The feasibility of fly ash as a very cheap material in the removal of different fission products from liquid radioactive waste was assessed.

On the ASR and ASR thermal residues characterization of full scale treatment plant.

Science.gov (United States)

Mancini, G; Viotti, P; Luciano, A; Fino, D

2014-02-01

In order to obtain 85% recycling, several procedures on Automotive Shredder Residue (ASR) could be implemented, such as advanced metal and polymer recovery, mechanical recycling, pyrolysis, the direct use of ASR in the cement industry, and/or the direct use of ASR as a secondary raw material. However, many of these recovery options appear to be limited, due to the possible low acceptability of ASR based products on the market. The recovery of bottom ash and slag after an ASR thermal treatment is an option that is not usually considered in most countries (e.g. Italy) due to the excessive amount of contaminants, especially metals. The purpose of this paper is to provide information on the characteristics of ASR and its full-scale incineration residues. Experiments have been carried out, in two different experimental campaigns, in a full-scale tyre incineration plant specifically modified to treat ASR waste. Detailed analysis of ASR samples and combustion residues were carried out and compared with literature data. On the basis of the analytical results, the slag and bottom ash from the combustion process have been classified as non-hazardous wastes, according to the EU waste acceptance criteria (WAC), and therefore after further tests could be used in future in the construction industry. It has also been concluded that ASR bottom ash (EWC - European Waste Catalogue - code 19 01 12) could be landfilled in SNRHW (stabilized non-reactive hazardous waste) cells or used as raw material for road construction, with or without further treatment for the removal of heavy metals. In the case of fly ash from boiler or Air Pollution Control (APC) residues, it has been found that the Cd, Pb and Zn concentrations exceeded regulatory leaching test limits therefore their removal, or a stabilization process, would be essential prior to landfilling the use of these residues as construction material. Copyright © 2013 Elsevier Ltd. All rights reserved.

Waste glass as partial mineral precursor in alkali-activated slag/fly ash system

NARCIS (Netherlands)

Zhang, S.; Keulen, A.; Arbi, K.; Ye, G.

2017-01-01

The feasibility of a waste glass powder residue (GP) from glass recycling as partial mineral precursor to produce alkali-activated materials is investigated. GP served as powder coal fly ash (PCFA) replacement within a reference system composed of 50% PCFA and 50% ground granulated blast furnace

Evaluating Growth of Zeolites on Fly Ash in Hydro-Thermally Heated Low Alkaline Solution

Science.gov (United States)

Jha, Bhagwanjee; Singh, D. N.

2017-12-01

Fly ash has been well established materials for synthesis of zeolites, under hydrothermally heated aqueous NaOH solution. Efficacy of such technique is reported to be improved when high molarity of NaOH is used. Consequently, highly alkaline waste solution, as by-product, is generally disposed of in the surrounding, which may contaminate the environment. In this context, less alkaline NaOH solution may become a safer option, which has not been tried in the past as per the literature. With this in view, the present study demonstrates effectiveness of the 0.5 M NaOH solution and critically monitors transition on the fly ash after hydrothermal treatment. As an enhancement over previous researchers, such activation of the fly ash finally results in remarkable morphological and mineralogical growth on the bulk material (the residue), which comprises of new nano-sized crystals (the zeolites Na-P1 and natrolite), after 24 h of activation of the fly ash.

Hydrolytic stability of heavy metal compounds in fly ash of a heat power plant

International Nuclear Information System (INIS)

Suslova, E.P.; Pertsikov, I.Z.

1991-01-01

Ash and slag from solid fuels are utilized widely in building materials and road surfaces, and in agriculture for soil acidulation. For all these uses it is important to know the amount and form of heavy metal compounds contained in ash and their likely behavior when ash and slag wastes are utilized. Studying the behavior of heavy metals in ash residues at contact with water media is important also because, for most trace elements, the authors lack experimental data that would enable us to predict their behavior after prolonged storage and industrial utilization. The present paper describes a study of lixiviation (at various pH in static conditions) of heavy metals form fly ash obtained by burning Azeisk coal. Homogenized ash selected from electric filter sections 1-4 was used, which has the following composition (%): SiO 2 59.8; Al 2 O 3 ; Fe 23 O 3 7.1; CaO 4.1; MgO 1.3; other 2.8. In a neutral medium, Ni, Cu, Zn, Pb, and Mn lixiviation was slight, amounting to 0.01-0.4%. During coal combustion, these elements apparently form compounds that are slightly soluble in water, although it is also possible that ash retains high adsorptivity for heavy metals. As a result, in these conditions the reverse process of sorption of heavy metals from the solution by fly ash is also possible, which would reduce the heavy metal concentration in the solution

Wildfire Ash: Chemical Composition, Ash-Soil Interactions and Environmental Impacts

Science.gov (United States)

Brook, Anna; Hamzi, Seham; Wittenberg, Lea

2015-04-01

produced ash has significant and not always constructive pedological, ecological, hydrological and geomorphological effects and impacts (Shakesby, 2011). Abundant scientific information is assembled either from control fires by collecting samples before and after wildfire event, or conducting laboratory experiments exanimating data under truly isolated conditions (Lugassi et al., 2013). However, an integration and synthesis of the knowledge about ash including deeper understanding of inter-correlation between chemical, physical and morphological compounds in open post-burn environment and its possible interactions in soil formation or impact on soil composition are highly needed. The main aim of the presented study was to advance the science of soil-fire relationship by recognizing the remains ash as a new soil-forming factor, on par with the traditionally recognized factors: parent material, topography, time, climate, organisms, and recently recognized human activity as the sixth factor. This research was conducted to develop new methods to assess impacts and quantify the contributions/influences of post-fire products, mainly ash, on soil composition and soil properties in post-burned environment. We conducted several controlled experiments using 40 soil samples (typical Mediterranean Rendzina soil, pH 6.84, a grayish-brown, humus- and free calcium carbonate- rich, intra-zonal). The samples include bare soils and different types and loads of forest litter, were exposed to different temperatures (200° C, 400° C and 600° C) in a muffle furnace for 2 hours (Pereira et al. 2011) as fire temperature plays a key role in determining ash properties. The ash produced at a low temperatures (50% carbon and retains many of the structural characteristics of the parent material. At higher temperatures, the residue ash is greyish, consisted of very fine particles that preserve almost none of the original structural characteristics of the fuel (Woods and Balfour, 2008) creating

Evaluation of the ecological risks to terrestrial wildlife associated with a coal ash disposal site

International Nuclear Information System (INIS)

Sample, B.E.

1994-01-01

Between 1955 and 1989, coal ash was deposited within an impounded watershed on the Oak Ridge Reservation, creating the 3.6 ha-Filled Coal Ash Pond (FCAP). The site has subsequently become vegetated, providing habitat for wildlife. To evaluate the risks that metals in the ash may pose to wildlife, ash, surface water, small mammal, and vegetation samples were collected and metal residues were determined. Metal concentrations, As and Se in particular, were elevated in ash, surface water, plant foliage, and small mammals relative to reference materials. Estimates of metal exposures received from food, water, and ash consumption were calculated for short-tailed shrews, white-footed mice, white-tailed deer, red fox, and red-tailed hawks. While shrews and mice were assumed to reside exclusively at and receive 100% exposure from the site, exposure experienced by deer, fox, and hawks was assumed to be proportional to the size of the site relative to their home range. Because deer had been observed to consume ash presumably for it's high sodium content, exposure experienced by deer consuming ash to meet sodium requirements was also estimated. To assess the risk of coal ash to wildlife, exposure estimates were compared to body-size adjusted toxicity data for each metal. These comparisons suggest that metals at the site may be detrimental to reproduction and survivorship of mice, shrews, deer and fox; hawks do not appear to be at risk

Impact of Collection Equipment on Ash Variability of Baled Corn Stover Biomass for Bioenergy

Energy Technology Data Exchange (ETDEWEB)

William Smith; Jeffery Einerson; Kevin Kenney; Ian J. Bonner

2014-09-01

Cost-effective conversion of agricultural residues for renewable energy hinges not only on the material’s quality but also the biorefinery’s ability to reliably measure quality specifications. The ash content of biomass is one such specification, influencing pretreatment and disposal costs for the conversion facility and the overall value of a delivered lot of biomass. The biomass harvest process represents a primary pathway for accumulation of soil-derived ash within baled material. In this work, the influence of five collection techniques on the total ash content and variability of ash content within baled corn stover in southwest Kansas is discussed. The equipment tested included a mower for cutting the corn stover stubble, a basket rake, wheel rake, or shred flail to gather the stover, and a mixed or uniform in-feed baler for final collection. The results showed mean ash content to range from 11.5 to 28.2 % depending on operational choice. Resulting impacts on feedstock costs for a biochemical conversion process range from $5.38 to $22.30 Mg-1 based on the loss of convertible dry matter and ash disposal costs. Collection techniques that minimized soil contact (shred flail or nonmowed stubble) were shown to prevent excessive ash contamination, whereas more aggressive techniques (mowing and use of a wheel rake) caused greater soil disturbance and entrainment within the final baled material. Material sampling and testing were shown to become more difficult as within-bale ash variability increased, creating uncertainty around feedstock quality and the associated costs of ash mitigation.

False deformation temperatures for ash fusibility associated with the conditions for ash preparation

Energy Technology Data Exchange (ETDEWEB)

Wall, T.F.; Gupta, S.K.; Gupta, R.P.; Sanders, R.H.; Creelman, R.A.; Bryant, G.W. [University of Newcastle, Callaghan, NSW (Australia). Cooperative Research Centre for Black Coal Utilization, Dept. of Chemical Engineering

1999-07-01

A study was made to investigate the fusibility behaviour of coal ashes of high ash fusion temperatures. Coals and ashes formed in the boiler were sampled in several Australian power stations, with laboratory ashes being prepared from the coals. The laboratory ashes gave lower values for the deformation temperature (DT) than the combustion ashes when the ash had low levels of basic oxide components. Thermo-mechanical analysis, quantitative X-ray diffraction and scanning electron microscopy were used to establish the mechanisms responsible for the difference. Laboratory ash is finer than combustion ash and it includes unreacted minerals (such as quartz, kaolinite and illite) and anhydrite (CaSO{sub 4}). Fusion events which appear to be characteristic of reacting illite, at temperatures from 900 to 1200{degree}C, were observed for the laboratory ashes, these being associated with the formation of melt phase and substantial shrinkage. The combustion ashes did not contain this mineral and their fusion events were observed at temperatures exceeding 1300{degree}C. The low DTs of coal ashes with low levels of basic oxides are therefore a characteristic of laboratory ash rather than that found in practical combustion systems. These low temperatures are not expected to be associated with slagging in pulverised coal fired systems. 10 refs., 3 figs., 2 tabs.

Investigation of additives for preventing ash fouling and sintering during barley straw combustion

International Nuclear Information System (INIS)

Wang, Liang; Skreiberg, Øyvind; Becidan, Michael

2014-01-01

Formation of potassium chloride reduces ash sintering temperature and causes fouling deposits in biomass combustion applications. In the present work, the capacity of two mineral additives zeolite 24A and kaolin to capture KCl were investigated. A series of thermogravimetric experiments were carried out to measure fractions of KCl retained in the two additives as function of reaction temperature and heating time. The residues from additive-KCl mixtures after heating treatment were analyzed by X-ray diffractometry (XRD). When heated at 900 °C for 1 h, the overall KCl capturing efficiencies of the two additives were 60% and 45% for zeolite 24A and kaolin respectively, which slightly decreased to 50% and 43% as the heating time increased to 12 h. At 1000 °C, the fractions of KCl captured by zeolite 24A and kaolin significantly decreased from 50% and 40% to 26% and 17%, as the KCl-additive mixtures were heated for 1 and 12 h, respectively. The decrease in of the overall KCl capturing efficiencies is mainly attributed to reduction of surface areas and chemically active compounds of the two additives with increasing temperature and heating time. The XRD analysis results showed that both zeolite 24A and kaolin can react with KCl to form different potassium aluminium silicates. It indicates that chemical reactions play an important role in the overall capturing process. The effects of zeolite 24A and kaolin on sintering behaviors of the barley straw ash were also investigated. The residues from sintering tests were analyzed by a combination of X-Ray diffractometry (XRD) and scanning electron microscopy equipped with energy dispersive X-Ray analysis (SEM-EDX). The barley straw ash melted intensively at elevated temperatures. Together with XRD analysis, the SEM-EDX analysis results revealed that severe melting of the barley straw ash was due to formation and fusion of low temperature melting potassium silicates. Addition of kaolin and zeolite 24A significantly

Immobilization in ceramic waste forms of the residues from treatment of mixed wastes

International Nuclear Information System (INIS)

Oversby, V.M.; van Konynenburg, R.A.; Glassley, W.E.; Curtis, P.G.

1993-11-01

The Environmental Restoration and Waste Management Applied Technology Program at LLNL is developing a Mixed Waste Management Facility to demonstrate treatment technologies that provide an alternative to incineration. As part of that program, we are developing final waste forms using ceramic processing methods for the immobilization of the treatment process residues. The ceramic phase assemblages are based on using Synroc D as a starting point and varying the phase assemblage to accommodate the differences in chemistry between the treatment process residues and the defense waste for which Synroc D was developed. Two basic formulations are used, one for low ash residues resulting from treatment of organic materials contaminated with RCRA metals, and one for high ash residues generated from the treatment of plastics and paper products. Treatment process residues are mixed with ceramic precursor materials, dried, calcined, formed into pellets at room temperature, and sintered at 1150 to 1200 degrees C to produce the final waste form. This paper discusses the chemical composition of the waste streams and waste forms, the phase assemblages that serve as hosts for inorganic waste elements, and the changes in waste form characteristics as a function of variation in process parameters

Cementing Efficiency of Low Calcium Fly Ash in Fly Ash Concretes

OpenAIRE

T. D. Gunneswara Rao; Mudimby Andal

2014-01-01

Research on the utilization of fly ash will no longer refer the fly ash as a waste material of thermal power plants. Use of fly ash in concrete making, makes the concrete economical as well as durable. The fly ash is being added to the concrete in three ways namely, as partial replacement to cement, as partial replacement to fine aggregates and as admixture. Addition of fly ash to the concrete in any one of the form mentioned above, makes the concrete more workable and durable than the conven...

Speciation and mobility of potentially toxic elements in municipal solid waste incineration bottom ash

NARCIS (Netherlands)

Schollbach, K.; Alam, Q.; Florea, M.V.A.; Brouwers, H.J.H.

2017-01-01

Bottom ash (BA) is the main residue from municipal solid waste incineration (MSWI), which can have some applications in construction materials, but is mostly landfilled in many countries. The main problem is the high concentration of potentially toxic elements (PTEs), particularly in the fine

Emerald ash borer biocontrol in ash saplings: the potential for early stage recovery of North American ash

Science.gov (United States)

In many parts of North America, ash stands have been reduced by the emerald ash borer (Agrilus planipennis) invasion to a few surviving mature trees and young basal sprouts, saplings, and seedlings. Without a seed bank, ash tree recovery will require survival and maturation of these younger cohorts...

Radioactivity of wood ash

International Nuclear Information System (INIS)

Rantavaara, A.; Moring, M.

2000-01-01

STUK (Finnish Radiation and Nuclear Safety Authority) has investigated natural and artificial radioactivity in wood ash and radiation exposure from radionuclides in ash since 1996. The aim was to consider both handling of ash and different ways of using ash. In all 87 ash samples were collected from 22 plants using entirely or partially wood for their energy production in 1996-1997. The sites studied represented mostly chemical forest industry, sawmills or district heat production. Most plants used fluidised bed combustion technique. Samples of both fly ash and bottom ash were studied. The activity concentrations of radionuclides in samples of, e.g., dried fly ash from fuel containing more than 80% wood were determined. The means ranged from 2000 to less than 50 Bq kg -1 , in decreasing order: 137 Cs, 40 K, 90 Sr, 210 Pb, 226 Ra, 232 Th, 134 Cs, 235 U. In bott radionuclide contents decreased in the same order as in fly ash, but were smaller, and 210 Pb was hardly detectable. The NH 4 Ac extractable fractions of activities for isotopes of alkaline elements (K, Cs) in bottom ash were lower than in fly ash, whereas solubility of heavier isotopes was low. Safety requirements defined by STUK in ST-guide 12.2 for handling of peat ash were fulfilled at each of the sites. Use of ash for land-filling and construction of streets was minimal during the sampling period. Increasing this type of ash use had often needed further investigations, as description of the use of additional materials that attenuate radiation. Fertilisation of forests with wood ash adds slightly to the external irradiation in forests, but will mostly decrease doses received through use of timber, berries, mushrooms and game meat. (orig.)

Size fractionation of waste-to-energy boiler ash enables separation of a coarse fraction with low dioxin concentrations

DEFF Research Database (Denmark)

Weidemann, E.; Allegrini, Elisa; Astrup, Thomas Fruergaard

2016-01-01

Polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/F) formed in modern Waste-to-Energy plants are primarily found in the generated ashes and air pollution control residues, which are usually disposed of as hazardous waste. The objective of this study was to explore the occurrence of PCDD....../F in different grain size fractions in the boiler ash, i.e. ash originating from the convection pass of the boiler. If a correlation between particle size and dioxin concentrations could be found, size fractionation of the ashes could reduce the total amount of hazardous waste. Boiler ash samples from ten...... sections of a boiler's convective part were collected over three sampling days, sieved into three different size fractions - 0.355. mm - and analysed for PCDD/F. The coarse fraction (>0.355. mm) in the first sections of the horizontal convection pass appeared to be of low toxicity with respect to dioxin...

UTILIZATION OF AGROINDUSTRIALES RESIDUES AS BIOFUELS AND BIOREFINERY

Directory of Open Access Journals (Sweden)

Deyanira Muñoz-Muñoz

2014-12-01

Full Text Available The use of residues generated in the process agro-industrials are interest worldwide. At present, research is this in lignocellulosic biomass for energy, fuels, chemicals and biomaterials through clean technologies and closed systems that conserve the environment. In this research, based on the characteristics of the typical agro-industrial residues of Cauca Department, sugarcane bagasse, sisal dust, cassava bran and the mixtures, was evaluated use as biorefinery. Were determined the thermal, physical chemical and morphologic properties in seven samples of residues, were performed exploratory tests, were determined pretreatments and applications and the possible use were identified. We conclude that the sample M6 with 9,93 % moisture, 4,12% ash, 43,97% carbon, 5,86% hydrogen, 0,43% nitrogen, 15 MJ/kg of lower heating value and 22,25%of cellulose, 9,30% of hemicellulose and 4,56% lignin, presents characteristics appropriate to be used in furnaces and boilers less power for the rural sector by the amount of ash, which keeps the low heating power stable and reduces the emission of particulate matter. For the thermal, physical, chemical and morphological characteristics, all the samples of M1 to M7, they can be hydrolyzed, densified and taken advantage like biofuel and / or biorefinery

Distillation, destructive

Energy Technology Data Exchange (ETDEWEB)

Brinjes, J F

1866-03-13

Continuous distillation of shale, boghead coal, or other noncaking bituminous material is effected in one or more rotating or oscillating horizontal retorts constructed to advance the charge. In the former case, internal spiral ribs or projections are provided. In the latter case, the retort is subdivided by annular flanges provided each with an opening, and a series of double inclined projections is disposed opposite the openings. An apparatus is shown in which the material is fed continuously from a hopper, and is advanced through upper and lower oscillating retorts, provided with annular flanges, double inclined projections, and longitudinal ribs or ledges. The retorts are supported on antifriction rollers. The retort is oscillated by means of a mangle wheel and a pinion on a shaft connected by a universal joint to a driving-shaft. The retort is oscillated from the retort by means of a chain connection. The retort is situated in a chamber separated by perforated brickwork from the actual furnace chamber, so that it is subjected to a lower temperature than the retort. The hopper delivers to crushing-rollers in a lower hopper which delivers to a shoot controlled by a sliding door. A hook on the retort is connected by a pipe to the retort, and a pipe leads from the hood to a condenser. A hood at the delivery end of the retort is connected by a pipe to an airtight cooler for the residue, which is discharged through doors into a truck of other receiver.

Fly Ash Formation during Suspension-Firing of Biomass. Effects of Residence Time and Fuel-Type

DEFF Research Database (Denmark)

Damø, Anne Juul; Jensen, Peter Arendt; Jappe Frandsen, Flemming

2017-01-01

particles were subjected to various analyses, including char burnout level, particle size distribution, elemental composition, and particle morphology and composition. Furthermore, the transient release, i.e. the vaporization of the flame-volatile inorganic elements K, Cl and S, from the burning fuel...... particles to the gas phase, has been quantified by using two different calculation methods. The ash formation mechanisms were found to be quite similar for straw and wood. The degree of conversion (char burn-out level) was generally good at residence times ≥ 1s. The size distribution of the residual fly ash...

Influence of Ash Applied to Oat Crop (Avena sativa L. Grown under Organic Fertilization with Manure

Directory of Open Access Journals (Sweden)

Benoni Lixandru

2012-10-01

Full Text Available The power plant ash is an inorganic residue with a variable chemical buildup according to the type of charcoal used and quality. Depositing, stabilizing and eventually reintegrating the ash in the natural circuit raises a series of problems due to its disastrous effect on biodiversity. Even with these problems, at a moderate micro and macro mineral content, power plant ash could present interesting agro technical and ecological alternatives. For this reason, the controlled integration of ash could put a stop to pollution with ash by reintegrating the material in the agricultural ecosystems.For this purpose, in the field of research of Ecological and Forage Crops from Faculty of Animal Science and Biotechnologies Timisoara, research was conducted over the influence of the reintegration of 40 t of ash per ha, produced by C.E.T. Timisoara, on the biomass production of oatmeal (Avena sativa L, fertilized by levels of 25 and 50 t per ha of manure. After harvesting, the analysis of the total biomass quantity, both above and underground, revealed similar results in all trials. In conditions that include heavy metal concentrations beneath normal geological values, conclude that the application of 40t per ha may be an agro technical solution for the integration of power plant ash in the agricultural ecosystem.

ADSORPTION OF THE DYE REACTIVE BLUE 5G IN RETORTED SHALE

Directory of Open Access Journals (Sweden)

R. Lambrecht

2015-03-01

Full Text Available Abstract In this study the influence of the volumetric flow rate and feed concentration was investigated for the adsorption of the reactive dye Blue 5G. Experiments were carried out in a bed packed with retorted shale, at 30 ºC. The ranges investigated were flow rate 2 -10 mL/min and the feed concentration 13-105 mg/L. Mathematical models were used to represent the dynamic sorption. The double resistance model considers the effects of the axial dispersion and the mass transfer resistance of the external film and inside the particles. As a result, the mass transfer coefficient of the external film and the internal mass transfer coefficient were estimated. The Thomas model was used to simulate the experimental data. In this model the fitted parameter was the adsorption kinetic constant. The first model provided an acceptable representation of the dynamic uptake of the reactive dye Blue 5G.

The Use of Fly Ash and Lime Sludge as Partial Replacement of Cement in Mortar

Directory of Open Access Journals (Sweden)

Vaishali Sahu

2014-01-01

Full Text Available The increased demand of drinking water and power has led huge generation of water treatment plant residue i.e. sludge and the thermal power plant by-product such as fly ash. Large quantities of sludge and fly ash are produced in India and disposed off by landfilling or dumping in and around sites. In this study fly ash and water softening sludge (lime sludge has been utilized in mortar. Two types of mortar (type I and II with four binder combinations have been tried. Binder I consists of 70% fly ash (FA and 30% lime sludge (LS , 0 % gypsum (G, binder II is 70% FA, 30% LS and 1% G, binder III is 50% FA, 30% LS and 20% cement and the binder IV is 40% FA, 40% LS with 20% cement. The effect of various combinations on strength has been discussed here. This paper outlines the composition of the composite material, method of preparation of mortar specimen, testing procedure and salient results thereof.

Ash-forming elements in four Scandinavian wood species part 3: Combustion of five spruce samples

Energy Technology Data Exchange (ETDEWEB)

Werkelin, Johan; Lindberg, Daniel; Skrifvars, Bengt-Johan; Hupa, Mikko [Aabo Akademi Process Chemistry Centre, Piispankatu 8, FI-20500 Turku (Finland); Bostroem, Dan [Energy Technology and Thermal Process Chemistry, Umeaa University, SE-901 87 Umeaa (Sweden)

2011-01-15

Forest residue is the remaining fraction after the outtake of timber, which comprises the tree tops and branches. It may as fuel cause damage to the combustion device through ash slagging and fouling. The objective of this work was to model the ash composition from well-specified samples of a spruce tree: wood, bark, twigs, needles, and shoots. Their ash at 1000 C was modelled using global chemical equilibrium calculations, and laboratory-made ash of the five samples was analyzed by XRD and SEM-EDXA. According to the results, the risk of slagging arises from the spruce foliage: molten alkali silicates from spruce needles and probably molten alkali phosphates from spruce shoots may cause problems in the furnace. Fouling caused by condensing alkali vapours can be produced by all five samples. The amount of alkali vapours in the flue gas was in the same order of magnitude for all five samples, in spite of large differences in their original alkali contents. (author)

Balance of natural radionuclides in the brown coal based power generation and harmlessness of the residues and side product utilization

International Nuclear Information System (INIS)

Schulz, Hartmut; Kunze, Christian; Hummrich, Holger

2017-01-01

During brown coal combustion a partial enrichment of natural radionuclides occurs in different residues. Residues and side product from brown coal based power generation are used in different ways, for example filter ashes and gypsum from flue gas desulfurization facilities are used in the construction materials fabrication and slags for road construction. Detailed measurement and accounting of radionuclides in the mass throughputs in coal combustion power plants have shown that the utilized gypsum and filter ashes are harmless in radiologic aspects.

Fluidised-bed combustion of gasification residue

Energy Technology Data Exchange (ETDEWEB)

Korpela, T.; Kudjoi, A.; Hippinen, I.; Heinolainen, A.; Suominen, M.; Lu Yong [Helsinki Univ. of Technology (Finland). Lab of Energy Economics and Power Plant Engineering

1996-12-01

Partial gasification processes have been presented as possibilities for future power production. In the processes, the solid materials removed from a gasifier (i.e. fly ash and bed material) contain unburnt fuel and the fuel conversion is increased by burning this gasification residue either in an atmospheric or a pressurised fluidised-bed. In this project, which is a part of European JOULE 2 EXTENSION research programme, the main research objectives are the behaviour of calcium and sulphur compounds in solids and the emissions of sulphur dioxide and nitrogen oxides (NO{sub x} and N{sub 2}O) in pressurised fluidised-bed combustion of gasification residues. (author)

Simplified method for the determination of strontium-90 in large amounts of bone-ash

International Nuclear Information System (INIS)

Patti, F.; Jeanmaire, L.

1966-06-01

The principle of the determination is based on a 3-step process: 1) concentrating the strontium by attacking the ash with nitric acid; 2) elimination of residual phosphoric ions by a double precipitation of strontium oxalate; and 3) extraction of yttrium 90, counted in the oxalate form. The advantages of the method: -) using simple techniques it makes it possible to process 50 g of ash; -) the initial concentration of strontium considerably reduces the volume of the solutions as well as the size of precipitates handled. Fuming nitric acid is used in a specially designed burette. (authors) [fr

The Swedish Ash Programme 2002-2008. Biomass, wastes, peat - any solid fuel but coal

Energy Technology Data Exchange (ETDEWEB)

Bjurstroem, Henrik; Herbert, Roger

2009-07-15

In Sweden, producers of combustion residues have since 2002 implemented a collaborative applied RandD programme aimed at the utilisation of combustion residues (ash). The fuels are biomass, wastes, peat - any solid fuel but coal. In this report, the main lines of the programme are described: Covers for landfills and mine tailings; Civil works, e.g. road-buildings, where both geotechnical and environmental questions have been addressed; Cement and concrete applications; Compensating soils for removing biomass and the mineral nutrients in the biomass. The emphasis of the Programme is on environmental questions, even if technical questions have been treated. The time perspective in this context is much longer than the 3-5 years that are usual in an applied RandD programme, i.e. decades after ash has been placed on a site, e.g. in a road, or spread to forest soil. New test fields have been created in the programme and old test fields have been evaluated in order to gather available information

Shaft-retort for treating waste materials, like washery waste, bituminous shale, oil-bearing sands and the like

Energy Technology Data Exchange (ETDEWEB)

Koppers, H

1916-10-29

A shaft-retort for converting waste materials, like washery waste, bituminous shale, oil-bearing sands, brown coal and non-coking mineral coal to oil and tar by supplying heat through the shaft wall formed of an iron-sheet to the material, which is forced through a feeding member perforated for the removal of gases and vapors, and moved downward in a thin layer on the shaft wall; that is characterized by the fact that the iron heating sheet is made rotatable for the purpose of equalizing overheating of itself and the material to be treated.

Trace element partitioning in ashes from boilers firing pure wood or mixtures of solid waste with respect to fuel composition, chlorine content and temperature.

Science.gov (United States)

Saqib, Naeem; Bäckström, Mattias

2014-12-01

Trace element partitioning in solid waste (household waste, industrial waste, waste wood chips and waste mixtures) incineration residues was investigated. Samples of fly ash and bottom ash were collected from six incineration facilities across Sweden including two grate fired and four fluidized bed incinerators, to have a variation in the input fuel composition (from pure biofuel to mixture of waste) and different temperature boiler conditions. As trace element concentrations in the input waste at the same facilities have already been analyzed, the present study focuses on the concentration of trace elements in the waste fuel, their distribution in the incineration residues with respect to chlorine content of waste and combustion temperature. Results indicate that Zn, Cu and Pb are dominating trace elements in the waste fuel. Highly volatile elements mercury and cadmium are mainly found in fly ash in all cases; 2/3 of lead also end up in fly ash while Zn, As and Sb show a large variation in distribution with most of them residing in the fly ash. Lithophilic elements such as copper and chromium are mainly found in bottom ash from grate fired facilities while partition mostly into fly ash from fluidized bed incinerators, especially for plants fuelled by waste wood or ordinary wood chips. There is no specific correlation between input concentration of an element in the waste fuel and fraction partitioned to fly ash. Temperature and chlorine content have significant effects on partitioning characteristics by increasing the formation and vaporization of highly volatile metal chlorides. Zinc and cadmium concentrations in fly ash increase with the incineration temperature. Copyright © 2014 Elsevier Ltd. All rights reserved.

Forest fuel, ashes and ecology

International Nuclear Information System (INIS)

Lundborg, A.

1994-01-01

Large-scale use of bioenergy is an essential measure if several of the major environmental problems are to be solved. However, it is important to utilize the possibilities available to produce biofuel without creating new environmental problems. Whole-tree removal gives a considerable reduction in the nitrogen lead which, in combination with the return of ashes, counteracts the nutrient imbalance and acidification in southern Sweden. Forestry of that kind should lead to lower total leaching of nitrogen in comparison with conventional forestry. In situations where there is high deposition of atmospheric sulphur and nitrogen, fuel removal with return of a moderate dose of slowly dissolvable ashes should be a good soil management measure. The humus status and flora/fauna always require some kind of consideration. With compensation measures and retained nutrient status there should be no problems with the humus status on most soils. However, on poor and dry soils, it is suitable to avoid whole-tree removal on account of the humus status. Consideration to nature includes, for example, increasing the number of broad-leaf trees, old trees and dead wood (preferably the trunks). These measures concern all types of forestry and are not linked directly with fuel removal. Removal of felling residues and return of ashes are of minor importance in comparison with this and fit well into forestry adapted to natural values. With correct planning and accomplishment of the removal of forest fuel the natural values of the forest can be retained or even improved. Forestry where fuel is also produced can be designed whereby negative effects are avoided at the same time as positive environmental effects are obtained. 68 refs, 5 figs, 3 tabs

Quality and generation rate of solid residues in the boiler of a waste-to-energy plant

DEFF Research Database (Denmark)

Allegrini, Elisa; Boldrin, Alessio; Jansson, S.

2014-01-01

The Danish waste management system relies significantly on waste-to-energy (WtE) plants. The ash produced at the energy recovery section (boiler ash) is classified as hazardous waste, and is commonly mixed with fly ash and air pollution control residues before disposal. In this study, a detailed...... characterization of boiler ash from a Danish grate-based mass burn type WtE was performed, to evaluate the potential for improving ash management. Samples were collected at 10 different points along the boiler's convective part, and analysed for grain size distribution, content of inorganic elements......, polychlorinated dibenzo-. p-dioxins and dibenzofurans (PCDD and PCDF), and leaching of metals. For all samples, PCDD and PCDF levels were below regulatory limits, while high pH values and leaching of e.g. Cl were critical. No significant differences were found between boiler ash from individual sections...

Fly ash carbon passivation

Science.gov (United States)

La Count, Robert B; Baltrus, John P; Kern, Douglas G

2013-05-14

A thermal method to passivate the carbon and/or other components in fly ash significantly decreases adsorption. The passivated carbon remains in the fly ash. Heating the fly ash to about 500 and 800 degrees C. under inert gas conditions sharply decreases the amount of surfactant adsorbed by the fly ash recovered after thermal treatment despite the fact that the carbon content remains in the fly ash. Using oxygen and inert gas mixtures, the present invention shows that a thermal treatment to about 500 degrees C. also sharply decreases the surfactant adsorption of the recovered fly ash even though most of the carbon remains intact. Also, thermal treatment to about 800 degrees C. under these same oxidative conditions shows a sharp decrease in surfactant adsorption of the recovered fly ash due to the fact that the carbon has been removed. This experiment simulates the various "carbon burnout" methods and is not a claim in this method. The present invention provides a thermal method of deactivating high carbon fly ash toward adsorption of AEAs while retaining the fly ash carbon. The fly ash can be used, for example, as a partial Portland cement replacement in air-entrained concrete, in conductive and other concretes, and for other applications.

Removal of uranium from simulated fly ash by chloride volatilization method

International Nuclear Information System (INIS)

Nobuaki, Sato; Yoshikatsu, Tochigi; Toshiki, Fukui; Takeo, Fujino

2003-01-01

Fly ash is generated from LWR nuclear power plant as a low-level waste, which is contaminated with a small amount of radioactive materials, composed mainly of uranium oxide. The constituents of the fly ash are similar to those of the ore; the major components of the ash are oxides of silicon, aluminum, sodium, magnesium, zinc, iron sodium and uranium. In this study, removal of uranium from the simulated fly ash, of which composition was U 3 O 8 : 10, CaO:25, SiO 2 : 25, Al 2 O 3 : 20, MgO: 10, ZnO:5, Fe 2 O 3 : 3 and Na 2 CO 3 : 2 wt%, by chloride volatilization method was examined. The simulated fly ash was chlorinated by the same manner as the dry way processing for the ore; namely, the ash was heated in a flow of chlorine in the presence of carbon at high temperatures. In the case of volatilization of uranium from U 3 O 8 and a simulated fly ash by chlorination using chlorine and carbon, it was seen that uranium of both samples showed similar volatilization behaviour: The volatilization ratio of uranium (VU) increased with increasing temperature from 800 to 1100 C. The VU value attained 99.9% at 1100 C. Iron, silicon and zinc showed similar behaviour to uranium, namely, they vaporized completely. The volatilization ratio of aluminum, magnesium and sodium were still high in a range 80-90%. The volatilization ratio of calcium was ∼40% under the same chlorination condition, though it changed to chloride. For recovery of uranium from fly ash by chlorination using chlorine in the presence of carbon, high volatilization ratio of uranium can be achieved at high temperatures. Volatilization ratio of other components also increases, which decreases the amount of decontaminated residue resulting in the reducing of decontamination effect. Selection of heating condition is important. (author)

Ashes to ashes: Large Fraxinus germplasm collections and their fates

Science.gov (United States)

Kim C. Steiner; Paul. Lupo

2010-01-01

As the emerald ash borer (EAB) threatens the survival of our ash species, measures should be taken to preserve their genetic variability in the event that we discover a way to restore populations destroyed by the beetle. As it happens, large germplasm collections exist for our most important and widely distributed eastern species of the genus, white ash (...

Improved leaching test methods for environmental assessment of coal ash and recycled materials used on construction

Science.gov (United States)

Changes in air pollution control at coal-fired power plants will result in lower emissions of mercury and other pollutants. Fly ash, flue gas desulfurization gypsum, and other air pollution control residues are used in agricultural, commercial, and engineering applications. Resea...

Seasonal changes in chemical and mineralogical composition of sewage sludge incineration residues and their potential for metallic elements and valuable components recovery

Science.gov (United States)

Kasina, Monika; Kowalski, Piotr R.; Michalik, Marek

2017-04-01

Increasing energy needs, the implementation of the circular economy principles and rising environmental awareness caused that waste management is becoming a major social and economic issue. The EU Member States have committed to a significant reduction in the amount of waste produced and landfilled and to use their inherent energy and raw materials potential. One of the most reasonable option to fulfil these commitments is waste incineration. The aim of the waste incineration is to reduce their volume and toxicity by disinfection and detoxification at high temperatures. Thermal process and reduction of volume allows the recovery of minerals and metallic elements from residues as well as the energy production (waste-to-energy strategy) during incineration. As a result of waste incineration a variety of solid residues (bottom ash, fly ash, air pollution control residues) and technological waste (gas waste, wastewater) are produced. The goal of this study is to characterize fly ash and air pollution control (APC) residues formed as a result of municipal sewage sludge incineration in terms of their chemical and mineral composition and their extractive potential. Residues were sampled quarterly to study their seasonal changes in composition. The fly ash was a Si-P-C-Fe-Al dominated material, whereas the APC residues composition was dominated by Na-rich soluble phases. The removal of soluble phase ( 98% of the material) from the APC residues by dissolution in deionised water caused significant mass reduction and concentration of non-soluble elements. The main mineral phases in fly ash were quartz, hematite, Fe-PO4, whitlockite and feldspar, while in APC thenardite, and in lower amount calcite, apatite and quartz were present. The chemical composition of fly ash was practically invariable in different seasons, but significant differences were observed in APC residues. The lowest concentrations of all elements and the highest TOC content were measured in the samples

Fusion characterization of biomass ash

Energy Technology Data Exchange (ETDEWEB)

Ma, Teng [State Key Laboratory ofMultiphase Complex Systems, Institute of Process Engineering, Chinese Academy of Sciences, No. 1 Zhongguancun North Second Street, Beijing 100190 (China); Sino-Danish Center for Education and Research, Beijing, 100190 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Fan, Chuigang; Hao, Lifang [State Key Laboratory ofMultiphase Complex Systems, Institute of Process Engineering, Chinese Academy of Sciences, No. 1 Zhongguancun North Second Street, Beijing 100190 (China); Li, Songgeng, E-mail: sgli@ipe.ac.cn [State Key Laboratory ofMultiphase Complex Systems, Institute of Process Engineering, Chinese Academy of Sciences, No. 1 Zhongguancun North Second Street, Beijing 100190 (China); Song, Wenli [State Key Laboratory ofMultiphase Complex Systems, Institute of Process Engineering, Chinese Academy of Sciences, No. 1 Zhongguancun North Second Street, Beijing 100190 (China); Lin, Weigang [State Key Laboratory ofMultiphase Complex Systems, Institute of Process Engineering, Chinese Academy of Sciences, No. 1 Zhongguancun North Second Street, Beijing 100190 (China); Department of Chemical and Biochemical Engineering, Technical University of Denmark, 2800 Kgs. Lyngby (Denmark)

2016-08-20

Highlights: • A novel method is proposed to analyze fusion characteristics of biomass ash. • T{sub m} can represent the severe melting temperature of biomass ash. • Compared with AFT, TMA is the better choice to analyze the fusion characteristics of biomass ash. - Abstract: The ash fusion characteristics are important parameters for thermochemical utilization of biomass. In this research, a method for measuring the fusion characteristics of biomass ash by Thermo-mechanical Analyzer, TMA, is described. The typical TMA shrinking ratio curve can be divided into two stages, which are closely related to ash melting behaviors. Several characteristics temperatures based on the TMA curves are used to assess the ash fusion characteristics. A new characteristics temperature, T{sub m}, is proposed to represent the severe melting temperature of biomass ash. The fusion characteristics of six types of biomass ash have been measured by TMA. Compared with standard ash fusibility temperatures (AFT) test, TMA is more suitable for measuring the fusion characteristics of biomass ash. The glassy molten areas of the ash samples are sticky and mainly consist of K-Ca-silicates.

Sulfidation treatment of molten incineration fly ashes with Na2S for zinc, lead and copper resource recovery.

Science.gov (United States)

Kuchar, D; Fukuta, T; Onyango, M S; Matsuda, H

2007-04-01

The present study focuses on the conversion of heavy metals involved in molten incineration fly ashes to metal sulfides which could be thereafter separated by flotation. The sulfidation treatment was carried out for five molten incineration fly ashes (Fly ash-A to Fly ash-E) by contacting each fly ash with Na(2)S solution for a period of 10 min to 6h. The initial molar ratio of S(2-) to Me(2+) was adjusted to 1.20. The conversion of heavy metals to metal sulfides was evaluated by measuring the S(2-) residual concentrations using an ion selective electrode. The formation of metal sulfides was studied by XRD and SEM-EDS analyses. In the case of Fly ash-A to Fly ash-D, more than 79% of heavy metals of zinc, lead and copper was converted to metal sulfides within the contacting period of 0.5h owing to a fast conversion of metal chlorides to metal sulfides. By contrast, the conversion of about 35% was achieved for Fly ash-E within the same contacting period, which was attributed to a high content of metal oxides. Further, the S(2-) to Me(2+) molar ratio was reduced to 1.00 to minimize Na(2)S consumption and the conversions obtained within the contacting period of 0.5h varied from 76% for Fly ash-D to 91% for Fly ash-C. Finally, soluble salts such as NaCl and KCl were removed during the sulfidation treatment, which brought about a significant enrichment in metals content by a factor varying from 1.5 for Fly ash-D to 4.9 for Fly ash-A.

An overview on characterization, utilization and leachate analysis of biomedical waste incinerator ash.

Science.gov (United States)

Rajor, Anita; Xaxa, Monika; Mehta, Ratika; Kunal

2012-10-15

Solid waste management is one of the major global environmental issues, as there is continuous increase in industrial globalization and generation of waste. Solid wastes encompass the heterogeneous mass of throwaways from the urban community as well as the homogeneous accumulations of agricultural, industrial and mineral wastes. Biomedical waste pose a significant impact on health and environment. A proper waste management system should be required to dispose hazardous biomedical waste and incineration should be the best available technology to reduce the volume of this hazardous waste. The incineration process destroys pathogens and reduces the waste volume and weight but leaves a solid material called biomedical waste ash as residue which increases the levels of heavy metals, inorganic salts and organic compounds in the environment. Disposal of biomedical waste ash in landfill may cause contamination of groundwater as metals are not destroyed during incineration. The limited space and the high cost for land disposal led to the development of recycling technologies and the reuse of ash in different systems. In order to minimize leaching of its hazardous components into the environment several studies confirmed the successful utilization of biomedical waste ash in agriculture and construction sector. This paper presents the overview on the beneficial use of ash in agriculture and construction materials and its leachate characteristics. This review also stressed on the need to further evaluate the leachate studies of the ashes and slag for their proper disposal and utilization. Copyright © 2012 Elsevier Ltd. All rights reserved.

Porous materials produced from incineration ash using thermal plasma technology.

Science.gov (United States)

Yang, Sheng-Fu; Chiu, Wen-Tung; Wang, To-Mai; Chen, Ching-Ting; Tzeng, Chin-Ching

2014-06-01

This study presents a novel thermal plasma melting technique for neutralizing and recycling municipal solid waste incinerator (MSWI) ash residues. MSWI ash residues were converted into water-quenched vitrified slag using plasma vitrification, which is environmentally benign. Slag is adopted as a raw material in producing porous materials for architectural and decorative applications, eliminating the problem of its disposal. Porous materials are produced using water-quenched vitrified slag with Portland cement and foaming agent. The true density, bulk density, porosity and water absorption ratio of the foamed specimens are studied here by varying the size of the slag particles, the water-to-solid ratio, and the ratio of the weights of the core materials, including the water-quenched vitrified slag and cement. The thermal conductivity and flexural strength of porous panels are also determined. The experimental results show the bulk density and the porosity of the porous materials are 0.9-1.2 g cm(-3) and 50-60%, respectively, and the pore structure has a closed form. The thermal conductivity of the porous material is 0.1946 W m(-1) K(-1). Therefore, the slag composite materials are lightweight and thermal insulators having considerable potential for building applications. Copyright © 2013 Elsevier Ltd. All rights reserved.

Evaluation of Changes in Index Properties of Lateritic Soil Stabilized with Fly Ash

Directory of Open Access Journals (Sweden)

Agapitus AMADI

2010-12-01

Full Text Available For soils to be suitable in civil engineering projects, they must meet existing local requirements for index properties in addition to certain strength criteria. Typically, specifications limit these properties to some threshold values which in most cases are project specific. Some lateritic soils in their natural state need some treatment/modification to meet these specification requirements. The objective of this study was to evaluate changes in the index properties (i.e., particle size distribution, Atterberg limits and compaction characteristics of a residually derived lateritic soil following fly ash application. Lateritic soil – fly ash mixtures with up to 20% fly ash by dry weight of soil were tested and specimens for compaction characteristics were prepared at different compaction states (optimum, dry and wet of optimum moisture content and compacted using British Standard Light (BSL compactive effort. While soil – fly ash mixtures containing up to 15% fly ash classify as CL according to USCS classification system and plotted above A-line in the plasticity chart, it was observed that changes in the gradation characteristics of soil sample treated with 20% fly ash resulted in the alteration of its classification to ML as well as the crossing of the A- line to the silty region. The liquid limit (LL varied from 42.2 to 29.53% representing 70% reduction while the plasticity index (PI of specimen treated with 20% fly ash was 16% lower than that of natural soil. The optimum moisture content (OMC ranged from 17.36% for the natural soil to 18.34% for soil mixtures containing 20% fly ash which yielded dry unit weight of 17.2kN/m3 for the natural soil and 16.1kN/m3 for samples treated with 20% fly ash. From the study, useful data were obtained showing substantial and desirable changes in the properties of lateritic soil as a civil engineering material on application of fly ash.

Effects of forest fuels extraction (whole tree harvesting) and ash recycling, experience and results from Swedish research

International Nuclear Information System (INIS)

Westling, Olle; Egnell, Gustaf; Dahlberg, Anders

2005-01-01

This review of Swedish research and environmental assessment studies during more than a decade is based on an ongoing synthesis of long term experiments with whole tree harvesting and wood ash recycling and other relevant research. The review is focused on effects of whole tree harvesting and compensatory fertilisation (wood ash) on forest production, biodiversity and soil and surface water. The studied extraction of biofuels (logging residues) from forest is primarily a complement to the conventional harvest of pulpwood and timber. General conclusions are that a large part of the theoretical potential of extraction of logging residues, in the form of branches and tops, can be utilised on condition that the losses of nutrients and acid neutralising capacity are compensated for through nutrient addition. To protect valuable fauna and flora, biotopes where conventional forestry is presently not applied should, with some exceptions, not be utilised for extraction of biofuels. The usage of wood ashes and other fertilisers will not increase the net accumulation of heavy metals and toxic organic elements in the forest ecosystems, on condition that the concentrations are low in the fertilisers

Mercury release from fly ashes and hydrated fly ash cement pastes

Science.gov (United States)

Du, Wen; Zhang, Chao-yang; Kong, Xiang-ming; Zhuo, Yu-qun; Zhu, Zhen-wu

2018-04-01

The large-scale usage of fly ash in cement and concrete introduces mercury (Hg) into concrete structures and a risk of secondary emission of Hg from the structures during long-term service was evaluated. Three fly ashes were collected from coal-fired power plants and three blend cements were prepared by mixing Ordinary Portland cement (OPC) with the same amount of fly ash. The releasing behaviors of Hg0 from the fly ash and the powdered hydrated cement pastes (HCP) were measured by a self-developed Hg measurement system, where an air-blowing part and Hg collection part were involved. The Hg release of fly ashes at room temperature varied from 25.84 to 39.69 ng/g fly ash during 90-days period of air-blowing experiment. In contrast, the Hg release of the HCPs were in a range of 8.51-18.48 ng/g HCP. It is found that the Hg release ratios of HCPs were almost the same as those of the pure fly ashes, suggesting that the hydration products of the HCP have little immobilization effect on Hg0. Increasing temperature and moisture content markedly promote the Hg release.

Hydration of fly ash cement and microstructure of fly ash cement pastes

Energy Technology Data Exchange (ETDEWEB)

Shiyuan, H.

1981-01-01

The strength development and hydration of fly ash cement and the influence of addition of gypsum on those were studied at normal and elevated temperatures. It was found that an addition of a proper amount of gypsum to fly ash cement could accelerate the pozzolanic reaction between CH and fly ash, and as a result, increase the strength of fly ash cement pastes after 28 days.

Fusion characterization of biomass ash

DEFF Research Database (Denmark)

Ma, Teng; Fan, Chuigang; Hao, Lifang

2016-01-01

The ash fusion characteristics are important parameters for thermochemical utilization of biomass. In this research, a method for measuring the fusion characteristics of biomass ash by Thermo-mechanical Analyzer, TMA, is described. The typical TMA shrinking ratio curve can be divided into two...... stages, which are closely related to ash melting behaviors. Several characteristics temperatures based on the TMA curves are used to assess the ash fusion characteristics. A new characteristics temperature, Tm, is proposed to represent the severe melting temperature of biomass ash. The fusion...... characteristics of six types of biomass ash have been measured by TMA. Compared with standard ash fusibility temperatures (AFT) test, TMA is more suitable for measuring the fusion characteristics of biomass ash. The glassy molten areas of the ash samples are sticky and mainly consist of K-Ca-silicates....

Coal Fly Ash Ceramics: Preparation, Characterization, and Use in the Hydrolysis of Sucrose

Directory of Open Access Journals (Sweden)

Ricardo Pires dos Santos

2014-01-01

Full Text Available Coal ash is a byproduct of mineral coal combustion in thermal power plants. This residue is responsible for many environmental problems because it pollutes soil, water, and air. Thus, it is important to find ways to reuse it. In this study, coal fly ash, obtained from the Presidente Médici Thermal Power Plant, was utilized in the preparation of ceramic supports for the immobilization of the enzyme invertase and subsequent hydrolysis of sucrose. Coal fly ash supports were prepared at several compaction pressures (63.66–318.30 MPa and sintered at 1200°C for 4 h. Mineralogical composition (by X-ray diffraction and surface area were studied. The ceramic prepared with 318.30 MPa presented the highest surface area (35 m2/g and amount of immobilized enzyme per g of support (76.6 mg/g. In assays involving sucrose inversion, it showed a high degree of hydrolysis (around 81% even after nine reuses and 30 days’ storage. Therefore, coal fly ash ceramics were demonstrated to be a promising biotechnological alternative as an immobilization support for the hydrolysis of sucrose.

Arsenic, chromium and mercury removal using mussel shell ash or a sludge/ashes waste mixture.

Science.gov (United States)

Seco-Reigosa, Natalia; Peña-Rodríguez, Susana; Nóvoa-Muñoz, Juan Carlos; Arias-Estévez, Manuel; Fernández-Sanjurjo, María J; Alvarez-Rodríguez, Esperanza; Núñez-Delgado, Avelino

2013-04-01

Different batches of valued mussel shell and waste mussel shell ash are characterised. Shell ash has pH > 12 and high electrical conductivities (between 16.01 and 27.27 dS m(-1)), while calcined shell shows pH values up to 10.7 and electrical conductivities between 1.19 and 3.55 dS m(-1). X-ray fluorescence, nitric acid digestion and water extractions show higher concentrations in shell ash for most parameters. Calcite is the dominant crystalline compound in this ash (95.6%), followed by aragonite. Adsorption/desorption trials were performed for mussel shell ash and for a waste mixture including shell ash, sewage sludge and wood ash, showing the following percentage adsorptions: Hg(II) >94%, As(V) >96% and Cr(VI) between 11 and 30% for shell ash; Hg(II) >98%, As(V) >88% and Cr(VI) between 30 and 88% for the waste mixture. Hg and As desorption was ash and the waste mixture, while Cr desorption was between 92 and 45% for shell ash, and between 19 and 0% for the mixture. In view of that, mussel shell ash and the mixture including shell ash, sewage sludge and wood ash could be useful for Hg(II) and As(V) removal.

Lethal trap trees: a potential option for emerald ash borer (Agrilus planipennis Fairmaire) management.

Science.gov (United States)

McCullough, Deborah G; Poland, Therese M; Lewis, Phillip A

2016-05-01

Economic and ecological impacts of ash (Fraxinus spp.) mortality resulting from emerald ash borer (EAB) (Agrilus planipennis Fairmaire) invasion are severe in forested, residential and urban areas. Management options include girdling ash trees to attract ovipositing adult beetles and then destroying infested trees before larvae develop or protecting ash with a highly effective, systemic emamectin benzoate insecticide. Injecting this insecticide and then girdling injected trees a few weeks later could effectively create lethal trap trees, similar to a bait-and-kill tactic, if girdling does not interfere with insecticide translocation. We compared EAB larval densities on girdled trees, trees injected with the emamectin benzoate insecticide, trees injected with the insecticide and then girdled 18-21 days later and untreated controls at multiple sites. Pretreatment larval densities did not differ among treatments. Current-year larval densities were higher on girdled and control trees than on any trees treated with insecticide at all sites. Foliar residue analysis and adult EAB bioassays showed that girdling trees after insecticide injections did not reduce insecticide translocation. Girdling ash trees to attract adult EAB did not reduce efficacy of emamectin benzoate trunk injections applied ≥ 18 days earlier and could potentially be used in integrated management programs to slow EAB population growth. © 2015 Society of Chemical Industry.

Sintering of a class F fly ash

Energy Technology Data Exchange (ETDEWEB)

Joseph J. Biernacki; Anil K. Vazrala; H. Wayne Leimer [Tennessee Technological University, Cookeville, TN (United States). Department of Chemical Engineering

2008-05-15

The sinterability of a class F fly ash was investigated as a function of processing conditions including sintering temperature (1050-1200{sup o}C) and sintering time (0-90 min). Density, shrinkage, splitting tensile strength, water absorption and residual loss on ignition (RLOI) were evaluated as measures of sintering efficiency. Scanning electron microscopy (SEM), X-ray microanalysis and X-ray diffraction was used to examine microstructure and phase development due to processing. The results show that premature densification can inhibit complete carbon removal and that carbon combustion is influenced by both internal and external mass transfer conditions. 18 refs., 10 figs., 1 tab.

Destructive distillation of coals

Energy Technology Data Exchange (ETDEWEB)

Rollason, A

1918-08-23

To obtain light oils and ammonia from coals having volatile and oxygen contents, the crushed material is mixed with 5 percent of ground amorphous calcium carbonate and distilled slowly in a cast iron retort to remove the water and light oils, the ammonia being synthesized at a later stage. The crushed residue is gasified in a producer by a blast of air and superheated steam at about 950/sup 0/C. The steam and air are passed very slowly at low pressure through the fuel to cause the dissociation of the atmospheric nitrogen molecules into atoms. The gases are then passed to a heater, having a temperature of 500/sup 0/C, and thence to a continuously working externally-heated retort charged with fuel, such as the hard retort residues, maintained below 850/sup 0/C. The water vapor in the gases is dissociated by the incandescent fuel, the oxygen combining with the carbon, and the lime present in the fuel causes the hydrogen to combine with the free nitrogen atoms, thus forming ammonia. The gases after leaving the retort are cooled down to 85 to 95/sup 0/C and the ammonia may be recovered by conversion into ammonium sulphate. The resultant cooled gases may again be charged with superheated steam and utilized again in the heater and retort.

Exploring the molecular and biochemical basis of ash resistance to emerald ash borer

Science.gov (United States)

Justin G.A. Whitehill; Daniel A. Herms; Pierluigi. Bonello

2010-01-01

Larvae of the emerald ash borer (EAB) (Agrilus planipennis) feed on phloem of ash (Fraxinus spp.) trees. It is hypothesized that the resistance of Asian species of ash (e.g., Manchurian ash, F. mandshurica) to EAB is due to endogenous defenses present in phloem tissues in the form of defensive proteins and/or...

Low temperature setting iron phosphate ceramics as a stabilization and solidification agent for incinerator ash contaminated with transuranic and RCRA metals

International Nuclear Information System (INIS)

Medvedev, P.G.; Hansen, M.; Wood, E.L.; Frank, S.M.; Sidwell, R.W.; Giglio, J.J.; Johnson, S.G.; Macheret, J.

1997-01-01

Incineration of combustible Mixed Transuranic Waste yields an ash residue that contains oxides of Resource Conservation and Recovery Act (RCRA) and transuranic metals. In order to dispose of this ash safely, it has to be solidified and stabilized to satisfy appropriate requirements for repository disposal. This paper describes a new method for solidification of incinerator ash, using room temperature setting iron phosphate ceramics, and includes fabrication procedures for these waste forms as well as results of the MCC-1 static leach test, XRD analysis, scanning electron microscopy studies and density measurements of the solidified waste form produced

Influence of digestion methods on the recovery of Iron, Zinc, Nickel, Chromium, Cadmium and Lead contents in 11 organic residues

Directory of Open Access Journals (Sweden)

Thalita Fernanda Abbruzzini

2014-02-01

Full Text Available There are currently many devices and techniques to quantify trace elements (TEs in various matrices, but their efficacy is dependent on the digestion methods (DMs employed in the opening of such matrices which, although "organic", present inorganic components which are difficult to solubilize. This study was carried out to evaluate the recovery of Fe, Zn, Cr, Ni, Cd and Pb contents in samples of composts and cattle, horse, chicken, quail, and swine manures, as well as in sewage sludges and peat. The DMs employed were acid digestion in microwaves with HNO3 (EPA 3051A; nitric-perchloric digestion with HNO3 + HClO4 in a digestion block (NP; dry ashing in a muffle furnace and solubilization of residual ash in nitric acid (MDA; digestion by using aqua regia solution (HCl:HNO3 in the digestion block (AR; and acid digestion with HCl and HNO3 + H2O2 (EPA 3050. The dry ashing method led to the greatest recovery of Cd in organic residues, but the EPA 3050 protocol can be an alternative method for the same purpose. The dry ashing should not be employed to determine the concentration of Cr, Fe, Ni, Pb and Zn in the residues. Higher Cr and Fe contents are recovered when NP and EPA 3050 are employed in the opening of organic matrices. For most of the residues analyzed, AR is the most effective method for recovering Ni. Microwave-assisted digestion methods (EPA3051 and 3050 led to the highest recovery of Pb. The choice of the DM that provides maximum recovery of Zn depends on the organic residue and trace element analyzed.

Properties and Leachability of Self-Compacting Concrete Incorporated with Fly Ash and Bottom Ash

Science.gov (United States)

Kadir, Aeslina Abdul; Ikhmal Haqeem Hassan, Mohd; Jamaluddin, Norwati; Bakri Abdullah, Mohd Mustafa Al

2016-06-01

The process of combustion in coal-fired power plant generates ashes, namely fly ash and bottom ash. Besides, coal ash produced from coal combustion contains heavy metals within their compositions. These metals are toxic to the environment as well as to human health. Fortunately, treatment methods are available for these ashes, and the use of fly ash and bottom ash in the concrete mix is one of the few. Therefore, an experimental program was carried out to study the properties and determine the leachability of selfcompacting concrete incorporated with fly ash and bottom ash. For experimental study, self-compacting concrete was produced with fly ash as a replacement for Ordinary Portland Cement and bottom ash as a replacement for sand with the ratios of 10%, 20%, and 30% respectively. The fresh properties tests conducted were slump flow, t500, sieve segregation and J-ring. Meanwhile for the hardened properties, density, compressive strength and water absorption test were performed. The samples were then crushed to be extracted using Toxicity Characteristic Leaching Procedure and heavy metals content within the samples were identified accordingly using Atomic Absorption Spectrometry. The results demonstrated that both fresh and hardened properties were qualified to categorize as self-compacting concrete. Improvements in compressive strength were observed, and densities for all the samples were identified as a normal weight concrete with ranges between 2000 kg/m3 to 2600 kg/m3. Other than that, it was found that incorporation up to 30% of the ashes was safe as the leached heavy metals concentration did not exceed the regulatory levels, except for arsenic. In conclusion, this study will serve as a reference which suggests that fly ash and bottom ash are widely applicable in concrete technology, and its incorporation in self-compacting concrete constitutes a potential means of adding value to appropriate mix and design.

Trace element partitioning in ashes from boilers firing pure wood or mixtures of solid waste with respect to fuel composition, chlorine content and temperature

Energy Technology Data Exchange (ETDEWEB)

Saqib, Naeem, E-mail: naeem.saqib@oru.se; Bäckström, Mattias, E-mail: mattias.backstrom@oru.se

2014-12-15

Highlights: • Different solids waste incineration is discussed in grate fired and fluidized bed boilers. • We explained waste composition, temperature and chlorine effects on metal partitioning. • Excessive chlorine content can change oxide to chloride equilibrium partitioning the trace elements in fly ash. • Volatility increases with temperature due to increase in vapor pressure of metals and compounds. • In Fluidized bed boiler, most metals find themselves in fly ash, especially for wood incineration. - Abstract: Trace element partitioning in solid waste (household waste, industrial waste, waste wood chips and waste mixtures) incineration residues was investigated. Samples of fly ash and bottom ash were collected from six incineration facilities across Sweden including two grate fired and four fluidized bed incinerators, to have a variation in the input fuel composition (from pure biofuel to mixture of waste) and different temperature boiler conditions. As trace element concentrations in the input waste at the same facilities have already been analyzed, the present study focuses on the concentration of trace elements in the waste fuel, their distribution in the incineration residues with respect to chlorine content of waste and combustion temperature. Results indicate that Zn, Cu and Pb are dominating trace elements in the waste fuel. Highly volatile elements mercury and cadmium are mainly found in fly ash in all cases; 2/3 of lead also end up in fly ash while Zn, As and Sb show a large variation in distribution with most of them residing in the fly ash. Lithophilic elements such as copper and chromium are mainly found in bottom ash from grate fired facilities while partition mostly into fly ash from fluidized bed incinerators, especially for plants fuelled by waste wood or ordinary wood chips. There is no specific correlation between input concentration of an element in the waste fuel and fraction partitioned to fly ash. Temperature and chlorine

Remote Sensing of Residue Management in Farms using Landsat 8 Sensor Imagery

Directory of Open Access Journals (Sweden)

M. A Rostami

2017-10-01

study were NDVI, BAI, NBR and NBRT. Classification accuracy was evaluated and expressed by confusion matrix and Kappa coefficient. Natural surfaces are rarely composed of a single uniform material. Spectral mixing occurs when materials with different spectral properties are represented by a single image pixel. The condition where scale of the mixing is large (macroscopic, mixing would occur in a linear fashion. However for microscopic situations, the mixing is generally nonlinear. The linear model ahich wasadopted in this study, assumes that there is no interaction between materials. Assumption of LSUA is that each pixel on the surface is a physical mixture of several constituents weighted by surface abundance, and the spectrum of the mixture is a linear combination of the endmember reflectance spectra. Within the context of this study, LSUA is a classification method that can determine contribution of each material (or endmember such as soil or residue for each image pixel. Results and Discussion The spectral response curve extracted from Landsat 8 image used as input into the LSUA model in ENVI software. As expected, crop burned residue (Ash spectra had lower reflectance when compared to the soil, residue and green plant spectra. The contrast between residue, green plant, soil and residue ash spectra was particularly evident in the NIR and SWIR bands. It is suggested that these bands are essential for residue discrimination. Differences of reflectance in the visible bands were minimal, providing little discrimination between residue, green plant, soil and residue ash. Burned area estimated by LSUA method from Landsat 8 image was correlated against the ground data (measured coincident to the ground data. The overall accuracy of classification with BAI index and LSUA method was 91.7 and 88.3 and Kappa coefficient was 0.89 and 0.84 respectively. Results indicated that burned field area can be located and its area can be estimated using Landsat 8 images. The Index BAI was

Effect of ash components on the ignition and burnout of high ash coals

Energy Technology Data Exchange (ETDEWEB)

Feng, B.; Yan, R.; Zheng, C.G. [Huazhong University of Science and Technology, Wuhan (China). National Laboratory of Coal Combustion

1998-11-01

The effect of the ash components on the ignition and burnout of four Chinese high ash coals were studied by thermogravimetric analysis. To investigate the influence of the ash components, comparative experiments were carried out with original, deashed and impregnated coals. Eleven types of ash components, such as SiO{sub 2}, CaCO{sub 3}, MgO, Na{sub 2}CO{sub 3}, K{sub 2}CO{sub 3}, Al{sub 2}O{sub 3}, TiO{sub 2}, Fe{sub 2}O{sub 3}, FeS{sub 2}, NH{sub 4}Fe(SO{sub 4}){sub 2}{center_dot}12H{sub 2}O and FeSO{sub 4},(NH{sub 4}){center_dot}6H{sub 2}O were used in the present study. It was found that most of the ash components have negative effects. The strong influence of some ash components suggests that the combustion characteristics of high ash coal may be determined by the ash composition. 5 refs., 2 figs., 2 tabs.

Biogas and mineral fertiliser production from plant residues of phytoremediation

Energy Technology Data Exchange (ETDEWEB)

Chu, Thi Thu Ha

2011-07-01

for the subsequent utilization of digestates as mineral fertilisers that supply the essential nutrients for crops like wheat, barley and oat. Another used method for attempt to produce mineral fertiliser from plant residues is thermal treatment. The process of burning at 1050 C reduced majority load of biomass. The contents of bottom ash from 5-29 % of different parts of plant residues were measured. Nutrients in bottom ash were rich due to the high proportions of nutritional elements such as potassium, magnesium, phosphorus, sulphur were transferred from the input plant materials into bottom ash. However, the concentrations of heavy metals, in particular cadmium and zinc, in ash were also high that exceeded the allowed limitation values and the possibility of fertiliser production was hard to perform by combustion. (orig.)

Environmental assessment of ashes - Course development by the Swedish Geotechnical Institute and the Swedish University of Agricultural Sciences in cooperation; Miljoeriskvaerdering av askor - Kursutveckling av SGI och SLU i samarbete

Energy Technology Data Exchange (ETDEWEB)

Tiberg, Charlotta; Olsson, Susanna; Thelin, Gunnar; Egnell, Gustav; Haanell, Bjoern

2008-06-15

Recently many research projects in the field of ashes from energy production and the possibilities to reuse them have been carried out in Sweden. A lot of material including new guidelines, recommendations et cetera has been published. It is difficult to navigate in this vast amount of information, also for professionals and persons in authority that shall assess the benefit and risks with using ashes in different applications. In this project current knowledge and material that is available in guidelines, handbooks, research, legislation and more have been compiled and is presented in this text book (also including list of references and project assignments.). The course material is intended to: Show possibilities to reuse ashes from energy production in different applications. Inform about ashes environmental and geotechnical properties Inform about available guidelines, reports et cetera. The intention is to use this text book as part of course literature at a university course that aims at raising the level of knowledge about ashes from energy production and support an environmentally friendly use of ashes. The text book can be used for selfstudies, in seminars, courses and so on. This text book is intended for anyone that is interested in environmental assessment, residual products and/or reuse of ashes, for example professionals and persons in authority at municipalities, students, producers of ash, persons that use or want to use residual products et cetera

Shedding of ash deposits

DEFF Research Database (Denmark)

Zbogar, Ana; Frandsen, Flemming; Jensen, Peter Arendt

2009-01-01

Ash deposits formed during fuel thermal conversion and located on furnace walls and on convective pass tubes, may seriously inhibit the transfer of heat to the working fluid and hence reduce the overall process efficiency. Combustion of biomass causes formation of large quantities of troublesome...... ash deposits which contain significant concentrations of alkali, and earth-alkali metals. The specific composition of biomass deposits give different characteristics as compared to coal ash deposits, i.e. different physical significance of the deposition mechanisms, lower melting temperatures, etc....... Low melting temperatures make straw ashes especially troublesome, since their stickiness is higher at lower temperatures, compared to coal ashes. Increased stickiness will eventually lead to a higher collection efficiency of incoming ash particles, meaning that the deposit may grow even faster...

Pengaruh Kombinasi Fly Ash dan Bottom Ash sebagai Bahan Substitusi pada Campuran Beton terhadap Sifat Mekanis

OpenAIRE

Yahya, Tengku Tantoni; Kurniawandy, Alex; Djauhari, Zulfikar

2017-01-01

Fly ash and bottom ash were waste that generated from the power plant burning coal process. Fly ash and bottom ash has the potential to be developed as a basic ingredient in concrete composites. This research aimed to obtain the properties of fresh concrete and hard concrete of the combined effect of fly ash and bottom ash as a substitute ingredient in composite concrete. This research has examined the influence of a combination of waste fly ash and bottom ash to the compressive strength of a...

Beyond waste: new sustainable fillers from fly ashes stabilization, obtained by low cost raw materials

Directory of Open Access Journals (Sweden)

N. Rodella

2016-09-01

Full Text Available A sustainable economy can be achieved only by assessing processes finalized to optimize the use of resources. Waste can be a relevant source of energy thanks to energy-from-waste processes. Concerns regarding the toxic fly ashes can be solved by transforming them into resource as recycled materials. The commitment to recycle is driven by the need to conserve natural resources, reduce imports of raw materials, save landfill space and reduce pollution. A new method to stabilize fly ash from Municipal Solid Waste Incinerator (MSWI at room temperature has been developed thanks to COSMOS-RICE LIFE+ project (www.cosmos-rice.csmt.eu. This process is based on a chemical reaction that occurs properly mixing three waste fly ashes with rice husk ash, an agricultural by-product. COSMOS inert can replace critical raw materials (i.e. silica, fluorspar, clays, bentonite, antimony and alumina as filler. Moreover the materials employed in the stabilization procedure may be not available in all areas. This paper investigates the possibility of substituting silica fume with corresponding condensed silica fume and to substitute flue-gas desulfurization (FGD residues with low-cost calcium hydroxide powder. The removal of coal fly ash was also considered. The results will be presented and a possible substitution of the materials to stabilize fly ash will be discussed.

Melting and Sintering of Ashes

DEFF Research Database (Denmark)

Hansen, Lone Aslaug

1997-01-01

-1300°C, and a trend of higher fusion temperatures with increasing contents of Al-silicates and quartz was found.c) Fly ashes, bottom ashes and deposits from coal/straw co-firing were all found to consist mainly of metal-alumina and alumina-silicates. These ashes all melt in the temperature range 1000......The thesis contains an experimental study of the fusion and sintering of ashes collected during straw and coal/straw co-firing.A laboratory technique for quantitative determination of ash fusion has been developed based on Simultaneous Thermal Analysis (STA). By means of this method the fraction......, the biggest deviations being found for salt rich (i.e. straw derived) ashes.A simple model assuming proportionality between fly ash fusion and deposit formation was found to be capable of ranking deposition rates for the different straw derived fly ashes, whereas for the fly ashes from coal/straw co-firing...

Investigation on Leaching Behaviour of Fly Ash and Bottom Ash Replacement in Self-Compacting Concrete

Science.gov (United States)

Kadir, Aeslina Abdul; Ikhmal Haqeem Hassan, Mohd; Bakri Abdullah, Mohd Mustafa Al

2016-06-01

Fly ash and bottom ash are some of the waste generated by coal-fired power plants, which contains large quantities of toxic and heavy metals. In recent years, many researchers have been interested in studying on the properties of self-compacting concrete incorporated with fly ash and bottom ash but there was very limited research from the combination of fly ash and bottom ash towards the environmental needs. Therefore, this research was focused on investigating the leachability of heavy metals of SCC incorporated with fly ash and bottom ash by using Toxicity Characteristic Leaching Procedure, Synthetic Precipitation Leaching Procedure and Static Leaching Test. The samples obtained from the coal-fired power plant located at Peninsula, Malaysia. In this study, the potential heavy metals leached out from SCC that is produced with fly ash as a replacement for Ordinary Portland Cement and bottom ash as a substitute for sand with the ratios from 10% to 30% respectively were designated and cast. There are eight heavy metals of concern such as As, Cr, Pb, Zn, Cu, Ni, Mn and Fe. The results indicated that most of the heavy metals leached below the permissible limits from the United States Environmental Protection Agency and World Health Organization limit for drinking water. As a conclusion, the minimum leaching of the heavy metals from the incorporation of fly ash and bottom ash in self-compacting concrete was found in 20% of fly ash and 20% of bottom ash replacement. The results also indicate that this incorporation could minimize the potential of environmental problems.

Processed bottom ash for replacing fine aggregate in making high-volume fly ash concrete

Directory of Open Access Journals (Sweden)

Antoni

2017-01-01

Full Text Available Bottom ash is a coal plant by-product that is abundant and underutilized. There is the potential use of bottom ash as a fine aggregate replacement in concrete mixtures; however, the problems of water absorption and uniformity of quality of the material need to be overcome first. In this study, bottom ash was treated by sieve separation and pounding to smaller particle size for use as a sand substitute. The physical and chemical characteristics of bottom ash were tested after treatment including water absorption, sieve analysis, and fineness modulus. Highvolume fly ash (HVFA mortar specimens were made and the compressive strength and flowability test using bottom ash after treatment are compared with that of the sand specimen. Low water to cementitious ratio was used to ensure higher strength from the cementitious paste and superplasticizer demand was determined for each treatment. The result showed that bottom ash can be used as fine aggregate replacement material. Sieve separation of the bottom ash could produce 75% of the compressive strength compared with the control sand specimen, whereas pounded bottom ash could have up to 96% of the compressive strength of the control specimen. A 28-day compressive strength of 45 MPa was achievable with 100% replacement of fine aggregate with bottom ash.

Encapsulation of mixed radioactive and hazardous waste contaminated incinerator ash in modified sulfur cement

International Nuclear Information System (INIS)

Kalb, P.D.; Heiser, J.H. III; Colombo, P.

1990-01-01

Some of the process waste streams incinerated at various Department of Energy (DOE) facilities contain traces of both low-level radioactive (LLW) and hazardous constituents, thus yielding ash residues that are classified as mixed waste. Work is currently being performed at Brookhaven National Laboratory (BNL) to develop new and innovative materials for encapsulation of DOE mixed wastes including incinerator ash. One such material under investigation is modified sulfur cement, a thermoplastic developed by the US Bureau of Mines. Monolithic waste forms containing as much as 55 wt % incinerator fly ash from Idaho national Engineering Laboratory (INEL) have been formulated with modified sulfur cement, whereas maximum waste loading for this waste in hydraulic cement is 16 wt %. Compressive strength of these waste forms exceeded 27.6 MPa. Wet chemical and solid phase waste characterization analyses performed on this fly ash revealed high concentrations of soluble metal salts including Pb and Cd, identified by the Environmental Protection Agency (EPA) as toxic metals. Leach testing of the ash according to the EPA Toxicity Characteristic Leaching Procedure (TCLP) resulted in concentrations of Pb and Cd above allowable limits. Encapsulation of INEL fly ash in modified sulfur cement with a small quantity of sodium sulfide added to enhance retention of soluble metal salts reduced TCLP leachate concentrations of Pb and Cd well below EPA concentration criteria for delisting as a toxic hazardous waste. 12 refs., 4 figs., 2 tabs

Process of heat-treating fuels of a bituminous nature, such as shale

Energy Technology Data Exchange (ETDEWEB)

Bergh, S V

1927-11-25

A process is described of heat treating any kind of material of a bituminous nature usable as fuel, like shale, mineral coal, peat, etc., whereby the fuel undergoes in a retort or the like a distillation for recovering from it the total amount or the greatest part of gaseous or vaporous distillation products. The warm distillation residue is burned, characterized by the retorts, containing the fuel going through, being wholly or partly surrounded by materials to be heated. These materials and the warm distillation residue resulting from the distillation during the burning are moved forward independently one of the other.

Management of solid residues in waste-to-energy and biomass systems

Energy Technology Data Exchange (ETDEWEB)

Vehlow, J.; Bergfeldt, B. [Forschungszentrum Karlsruhe GmbH Technik und Umwelt (Germany). Inst. fuer Technische Chemie; Wilen, C.; Ranta, J. [VTT Technical Research Centre of Finland, Espoo (Finland); Schwaiger, H. [Forschungsgesellschaft Joanneum mbH, Graz (Austria); Visser, H.J.M. [ECN Energy Research Centre of the Netherlands, Petten (Netherlands); Gu, S.; Gyftopoulou, E.; Brammer, J. [Aston Univ., Birmingham (United Kingdom)

2007-12-15

A literature review has been performed for getting in-depth information about quality of residues from thermal processes for waste and biomass as well as their disposal or utilisation options and current practices. Residues from waste incineration have been subject to intense research programs for many years and it can be concluded that the quality of bottom ashes has meanwhile a high standard. The question whether an utilisation as secondary building material is accepted or not depends on the definition of acceptable economic impac. For filter ashes and gas cleaning residues the situation is more complex. Their quality is known: due to their high inventory of heavy metals and organic micro-pollutants they are classified as hazardous waste which means they require specific measures for their safe long-term disposal. A number of stabilisation and treatment processes for filter ashes and gas cleaning residues including the recovery of species out of these materials have been developed but none has been implemented in full scale due to economic constraints. There is reason to speculate that even recovery processes which are not profitable for private companies might point out economically useful if future and long-term costs which have to be covered of the society, e.g. for rehabilitation of contaminated sites, are taken into account. Their quality as well as that of residues from combustion of contaminated biomass is mainly depending on the quality of the fuel. The inventory of critical ingredients in fuel produced from waste or waste fractions, especially of halogens and heavy metals, is often rather high and shows typically a wide range of variation. A reliable quality control for such fuels is very difficult. Other residues can - like gas cleaning residues from waste incineration - be inertised in order to meet the criteria for the access to cheaper landfills than those for hazardous waste. A similar conclusion can be drawn for the quality and management of

Steam gasification of a thermally pretreated high lignin corn stover simultaneous saccharification and fermentation digester residue

Energy Technology Data Exchange (ETDEWEB)

Howe, Daniel T.; Taasevigen, Danny; Garcia-Perez, Manuel; McDonald, Armando G.; Li, Guosheng; Wolcott, Michael

2017-01-01

Efficient conversion of all components in lignocellulosic biomass is essential to realizing economic feasibility of biorefineries. However, when utilizing biochemical pathways, lignin cannot be fermented. Furthermore, the high lignin and high ash residue resulting from simultaneous saccharification and fermentation (SSF) reactors is difficult to thermochemically process due to feed line plugging and bed agglomeration. In this study a corn stover SSF digester residue was thermally pretreated at 300°C for 22.5 minutes (min) and then gasified in a bubbling fluidized bed gasifier to study the effect of thermal pretreatment on its processing behavior. Untreated, pelletized SSF residue was gasified at the same conditions to establish the baseline processing behavior. Results indicate that the thermal pretreatment process removes a substantial portion of the polar and non-polar extractives, with a resultant increase in the concentration of lignin, cellulose, and ash. Feed line plugging was not observed, although bed agglomeration was occurring at similar rates for both feedstocks, suggesting that overall ash content is the most important factor affecting bed agglomeration. Benzene, phenol, and polyaromatic hydrocarbons in the tar were present at higher concentrations in the treated material, with higher tar loading in the product gas. Total product gas generation is lower for the treated material, although the overall gas composition does not change.

Quality and generation rate of solid residues in the boiler of a waste-to-energy plant.

Science.gov (United States)

Allegrini, E; Boldrin, A; Jansson, S; Lundtorp, K; Fruergaard Astrup, T

2014-04-15

The Danish waste management system relies significantly on waste-to-energy (WtE) plants. The ash produced at the energy recovery section (boiler ash) is classified as hazardous waste, and is commonly mixed with fly ash and air pollution control residues before disposal. In this study, a detailed characterization of boiler ash from a Danish grate-based mass burn type WtE was performed, to evaluate the potential for improving ash management. Samples were collected at 10 different points along the boiler's convective part, and analysed for grain size distribution, content of inorganic elements, polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD and PCDF), and leaching of metals. For all samples, PCDD and PCDF levels were below regulatory limits, while high pH values and leaching of e.g. Cl were critical. No significant differences were found between boiler ash from individual sections of the boiler, in terms of total content and leaching, indicating that separate management of individual ash fractions may not provide significant benefits. Copyright © 2014 Elsevier B.V. All rights reserved.

A database for the program 'Environmentally correct utilization of ashes'; Databas inom delprogrammet 'Miljoeriktig anvaendning av askor'

Energy Technology Data Exchange (ETDEWEB)

Bjurstroem, Henrik; Rydstrand, Camilla; Berg, Magnus; Wikman, Karin [AaF-Energi and Miljoe AB, Stockholm (Sweden)

2004-01-01

In the program 'Environmentally correct utilization of ashes' that is active 2002-2005 at the Swedish Thermal Research Institute (Vaermeforsk), R and D studies of the properties of ashes or combustion residues are being carried out and will be carried out. It may be difficult to obtain an overview of these data if these are dispersed in a large number of reports. These data are valuable as they may be used as references on the properties of ashes (these do vary widely, and knowledge of the range within which they vary as well of as the cause to effect chain is far from exhaustive). They also form a basis for continued work in this area. Furthermore, one of the aims of the R and D program is to define criteria for the use of ashes in various situations. Such criteria are generally formulated using quantitative requirements on technical as well as environmental properties. A flexible database has been created in Access in order to store these data on ashes as an easy-to-access reference. The goal was satisfaction of both a user of ashes and a producer of ashes. The information that can be stored stretches from the fuel, the design of the combustion plant to properties specific to a given utilization such as shear module or permeability. Attention has especially been paid to the facts that fuels are often mixed and that ashes are often mixed with other ashes or with other materials. In this first stage, data have been stored in the database for 22 ash samples that have been studied in eight R and D projects.

Distilling carbonaceous material

Energy Technology Data Exchange (ETDEWEB)

Karrick, L C

1926-11-02

Coal, shale and the like are distilled in a current of superheated steam which is passed into a retort at about midway between its ends a further supply being if necessary introduced at the bottom to generate water-gas, and the coke being dry quenched in a hopper below the retort. Combustion products may also be introduced and the temperature may be varied from 950 to 1725/sup 0/F, oil, gas, resin and a residual coke having good adsorbent value, being obtained. The charge from hoppers and auxiliary hoppers is fed to retorts situated between gas and steam preheaters, the rate of downward movement being controlled by discharge rollers having arms, counterweighted rocking arms allowing the residue to be fed downwards into hoppers. Steam from a pipe is superheated in horizontal passages, and admitted through ports into the retort. Preheated fuel gas is burnt in combustion flues and passes down through vertical flues, across horizontal flues and up flues adjacent the retorts, from which by ports and flues it passes down a chamber having an air or gas preheater each having two independent systems, one discharging into the combustion chamber beneath it and the other into an adjacent chamber. Air or gas enters by pipes and after being heated in pipes is fed by ports to the chamber. The volatiles pass off through outlets leading to a main air cooled condenser and a water-cooled condenser delivering to a separating tank connecting with pipes for quenching the residues and with pipes to preheat the charge in the hoppers and maintain a gas barrier the rein. Superheated steam may also be admitted through ports to generate water-gas and increase the total volume of gases and combustion products may be introduced through ports. The upper part of the retort is made of cast iron, the high temperature parts of silica or carborundum brick, and the lower part of chrome iron or other metal.

Ash fusion temperatures and the transformations of coal ash particles to slag

Energy Technology Data Exchange (ETDEWEB)

Gupta, S.K.; Wall, T.F.; Creelman, R.A.; Gupta, R.P. [University of Newcastle, Newcastle, NSW (Australia). CRC for Black Coal Utilisation

1998-07-01

A mechanistic study is detailed in which coal ash is heated with its shrinkage measured continuously up to a temperature of 1600{degree}C. The temperature corresponding to the rapid rate of shrinkage correspond to the formation of eutectics identified on phase diagrams. Samples were therefore heated to these temperatures, cooled rapidly and examined using a scanning electron microscope (SEM) to identify the associated chemical and physical changes. The progressive changes in the range of chemical composition (from SEM), the extent of undissolved ash particles and porosity were then quantified and related to homogenisation, viscosity and ash fusion mechanisms. Alternate ash fusion temperatures based on different levels of shrinkage have also been suggested to characterise the ash deposition tendency of the coals. 13 refs., 9 figs.

Classification and categorization of treatment methods for ash generated by municipal solid waste incineration: a case for the 2 greater metropolitan regions of Greece.

Science.gov (United States)

Karagiannidis, A; Kontogianni, St; Logothetis, D

2013-02-01

The primary goal of managing MSW incineration residues is to avoid any impact on human health or the environment. Incineration residues consist of bottom ash, which is generally considered as rather harmless and fly ash which usually contains compounds which are potentially harmful for public health. Small quantities of ash (both bottom and fly) are produced currently in Greece, mainly from the healthcare waste incineration facility in Attica region. Once incineration plants for MSW (currently under planning) are constructed in Greece, the produced ash quantities will increase highly. Thus, it is necessary to organize, already at this stage, a roadmap towards disposal/recovery methods of these ash quantities expected. Certain methods, related to the treatment of the future generated ash which are more appropriate to be implemented in Greece are highlighted in the present paper. The performed analysis offers a waste management approach, having 2016 as a reference year for two different incineration rates; 30% and 100% of the remaining MSW after recycling process. The results focus on the two greater regions of Greece: Attica and Central Macedonia. The quantity of potential future ash generation ranges from 137 to 459 kt for Attica region and from 62 to 207 kt for central Macedonia region depending on the incineration rate applied. Three alternative scenarios for the treatment of each kind of ash are compiled and analysed. Metal recovery and reuse as an aggregate in concrete construction proved to be the most advantageous -in terms of economy-bottom ash management scenario. Concerning management of the fly ash, chemical treatment with phosphoric solution addition results to be the lowest total treatment cost and is considered as the most profitable solution. The proposed methodology constitutes a safe calculation model for operators of MSW incineration plants regardless of the region or country they are located in. Crown Copyright © 2012. Published by Elsevier Ltd

Interspecific proteomic comparisons reveal ash phloem genes potentially involved in constitutive resistance to the emerald ash borer.

Science.gov (United States)

Whitehill, Justin G A; Popova-Butler, Alexandra; Green-Church, Kari B; Koch, Jennifer L; Herms, Daniel A; Bonello, Pierluigi

2011-01-01

The emerald ash borer (Agrilus planipennis) is an invasive wood-boring beetle that has killed millions of ash trees since its accidental introduction to North America. All North American ash species (Fraxinus spp.) that emerald ash borer has encountered so far are susceptible, while an Asian species, Manchurian ash (F. mandshurica), which shares an evolutionary history with emerald ash borer, is resistant. Phylogenetic evidence places North American black ash (F. nigra) and Manchurian ash in the same clade and section, yet black ash is highly susceptible to the emerald ash borer. This contrast provides an opportunity to compare the genetic traits of the two species and identify those with a potential role in defense/resistance. We used Difference Gel Electrophoresis (DIGE) to compare the phloem proteomes of resistant Manchurian to susceptible black, green, and white ash. Differentially expressed proteins associated with the resistant Manchurian ash when compared to the susceptible ash species were identified using nano-LC-MS/MS and putative identities assigned. Proteomic differences were strongly associated with the phylogenetic relationships among the four species. Proteins identified in Manchurian ash potentially associated with its resistance to emerald ash borer include a PR-10 protein, an aspartic protease, a phenylcoumaran benzylic ether reductase (PCBER), and a thylakoid-bound ascorbate peroxidase. Discovery of resistance-related proteins in Asian species will inform approaches in which resistance genes can be introgressed into North American ash species. The generation of resistant North American ash genotypes can be used in forest ecosystem restoration and urban plantings following the wake of the emerald ash borer invasion.

Electrodialytic upgrading of municipal waste incineration fly ash for reuse

DEFF Research Database (Denmark)

Jensen, Pernille Erland; Kirkelund, Gunvor Marie; Ottosen, Lisbeth M.

2012-01-01

As incineration becomes a more widespread means of waste treatment, volumes of incineration residues increase and new means of handling become a demand. Municipal Solid Waste Incineration (MSWI) fly ash is hazardous material, which is presently disposed off as such; primarily due to its high......]. In order to optimize the process and reach the lowest possible leachability of target constituents (As, Ba, Cd, Cr, Cu, Mn, Ni, Pb, Zn, Cl, Na and SO4) at minimum time and energy consumption, the present work gives results of 10 pilot scale (8 kg MSWI fly ash each) electrodialysis experiments at different...... to investigate the leachability of salts and toxic elements as a function of treatment time and current density. Results show that a delicate balance between pH and treatment-time exist and that continuous monitoring of pH and conductivity may be used for controlling of the process at an industrial scale...

Environmental impacts of the coal ash spill in Kingston, Tennessee: an 18-month survey.

Science.gov (United States)

Ruhl, Laura; Vengosh, Avner; Dwyer, Gary S; Hsu-Kim, Heileen; Deonarine, Amrika

2010-12-15

An 18 month investigation of the environmental impacts of the Tennessee Valley Authority (TVA) coal ash spill in Kingston, Tennessee combined with leaching experiments on the spilled TVA coal ash have revealed that leachable coal ash contaminants (LCACs), particularly arsenic, selenium, boron, strontium, and barium, have different effects on the quality of impacted environments. While LCACs levels in the downstream river water are relatively low and below the EPA drinking water and ecological thresholds, elevated levels were found in surface water with restricted water exchange and in pore water extracted from the river sediments downstream from the spill. The high concentration of arsenic (up to 2000 μg/L) is associated with some degree of anoxic conditions and predominance of the reduced arsenic species (arsenite) in the pore waters. Laboratory leaching simulations show that the pH and ash/water ratio control the LCACs' abundance and geochemical composition of the impacted water. These results have important implications for the prediction of the fate and migration of LCACs in the environment, particularly for the storage of coal combustion residues (CCRs) in holding ponds and landfills, and any potential CCRs effluents leakage into lakes, rivers, and other aquatic systems.

Destructive distillation

Energy Technology Data Exchange (ETDEWEB)

Mitting, E K

1882-08-09

The broken-up shale is placed in cast-iron retorts, heated externally, having exit tubes placed at a low level. Each retort is provided with a steam-pipe with a regulating-cock outside, the pipe being carried around the walls of the retort in a spiral or zig-zag way to ensure superheating of the steam, perforations being made in the pipe to allow exit for the steam into the retort. The steam, which may if desired be superheated before entrance, is passed into the retort when the latter has attained a temperature of from 210 to 250/sup 0/C and the passage is continued while the temperature rises, as long as distillation goes on. The exit pipe to the retort leads to a condenser of much condensing-surface, provided with a drag obtained by an exhausting steam jet or otherwise. The distilled products consist of tar, oils, wax, ammoniacal water (stated to be in greater proportion through the use of the process), and lighting and heating gas. The latter gas goes through a scrubber to a gasholder. The carbonaceous residue in the retort is discharged when cooled below a red heat, into sheet-iron cylinders, with tightly fitting lids, to avoid as far as possible contact with the atmosphere.

Stabilization of APC residues from waste incineration with ferrous sulfate on a semi-industrial scale

DEFF Research Database (Denmark)

Lundtorp, Kasper; Jensen, Dorthe Lærke; Christensen, Thomas Højlund

2002-01-01

A stabilization method for air pollution control (APC) residues from municipal solid waste incineration (MSWI) involving mixing of the residue with water and FeSO4 has been demonstrated on a semi-industrial scale on three types of APC residues: a semidy (SD) APC residue, a fly ash (FA), and an FA...... mixed with sludge (FAS) from a wet flue gas cleaning system. The process was performed in batches of 165-175 kg residue. It generates a wastewater that is highly saline but has a low content of heavy metals such as Cd, Cr, and Pb. The stabilized and raw residues have been subject to a range of leaching...

Wet treatment of ashes, a survey of methods; Vaat rening av askor, metodoeversikt

Energy Technology Data Exchange (ETDEWEB)

Bjurstroem, Henrik [AaF-Energi och Miljoe AB, Stockhom (Sweden); Steenari, Britt-Marie [Chalmers Univ. of Technology, Goeteborg (Sweden)

2003-10-01

incinerators. Several activities presently under way have not yet resulted in a full-scale plant. At present, it does not seem interesting to treat bioashes that are to be spread on forest soils using a wet method. Today, there is not any proven method to keep potassium in the ash or to return it to the ash. Electrodialysis could be such a technique, but at present it is still in the research stage. Extraction of metals or other components from ash does not seem to be economically profitable on its own merits today. The overall impression is that wet methods are a feasible way to treat ashes, but that they need to be studied in each case for the fly ashes or air pollution control residues that are produced in Swedish plants.

Influence of Fly Ash on the Compressive Strength of Foamed Concrete at Elevated Temperature

Directory of Open Access Journals (Sweden)

Ahmad H.

2014-01-01

Full Text Available Foamed concrete is a lightweight concrete that is widely used in the construction industry recently. This study was carried out to investigate the influence of fly ash as a cement replacement material to the residual compressive strength of foamed concrete subjected to elevated temperature. For this study, the foamed concrete density was fixed at 1300 kg/m3 and the sand-cement ratio and water-cement was set at 1:2 and 0.45, respectively. The samples were prepared and tested at the age of 28 days. Based on the results, it has been found that with 25% inclusion of fly ash, the percentage of compressive strength loss was decreased by 3 – 50%.

Survey for tolerance to emerald ash borer within North American ash species

Science.gov (United States)

Jennifer L. Koch; Mary E. Mason; David W. Carey; Kathleen Knight; Therese Poland; Daniel A. Herms

2010-01-01

Since the discovery of the emerald ash borer (EAB) near Detroit, MI, in 2002, more than 40 million ash trees have been killed and another 7.5 billion are at risk in the United States. When the EAB outbreak was initially discovered, our native ash species appeared to have no resistance to the pest.

Cast-concrete products made with FBC ash and wet-collected coal-ash

Energy Technology Data Exchange (ETDEWEB)

Naik, T.R.; Kraus, R.N.; Chun, Y.M.; Botha, F.D. [University of Wisconsin, Milwaukee, WI (United States)

2005-12-01

Cast-concrete hollow blocks, solid blocks, and paving stones were produced at a manufacturing plant by replacing up to 45% (by mass) of portland cement with fluidized bed combustion (FBC) coal ash and up to 9% of natural aggregates with wet-collected, low-lime, coarse coal-ash (WA). Cast-concrete product specimens of all three types exceeded the compressive strength requirements of ASTM from early ages, with the exception of one paving-stone mixture, which fell short of the requirement by less than 10%. The cast-concrete products made by replacing up to 40% of cement with FBC ash were equivalent in strength (89-113% of control) to the products without ash. The abrasion resistance of paving stones was equivalent for up to 34% FBC ash content. Partial replacement of aggregates with WA decreased strength of the products. The resistance of hollow blocks and paving stones to freezing and thawing decreased appreciably with increasing ash contents. The cast-concrete products could be used indoors in regions where freezing and thawing is a concern, and outdoors in a moderate climate.

Can ash clog soil pores?

Science.gov (United States)

Stoof, Cathelijne; Stoof, Cathelijne; Gevaert, Anouk; Gevaert, Anouk; Baver, Christine; Baver, Christine; Hassanpour, Bahareh; Hassanpour, Bahareh; Morales, Veronica; Morales, Veronica; Zhang, Wei; Zhang, Wei; Martin, Deborah; Martin, Deborah; Steenhuis, Tammo; Steenhuis, Tammo

2015-04-01

Wildfire can greatly increase a landscape's vulnerability to flooding and erosion events, and ash is thought to play a large role in controlling runoff and erosion processes after wildfire. Although ash can store rainfall and thereby reduce runoff and erosion for a limited period after wildfires, it has also been hypothesized to clog soil pores and reduce infiltration. Several researchers have attributed the commonly observed increase in runoff and erosion after fire to the potential pore-clogging effect of ash. Evidence is however incomplete, as to date, research has solely focused on identifying the presence of ash in the soil, with the actual flow processes associated with the infiltration and pore-clogging of ash remaining a major unknown. In several laboratory experiments, we tested the hypothesis that ash causes pore clogging to the point that infiltration is hampered and ponding occurs. We first visualized and quantified pore-scale infiltration of water and ash in sand of a range of textures and at various infiltration rates, using a digital bright field microscope capturing both photo and video. While these visualization experiments confirm field and lab observation of ash washing into soil pores, we did not observe any clogging of pores, and have not been able to create conditions for which this does occur. Additional electrochemical analysis and measurement of saturated hydraulic conductivity indicate that pore clogging by ash is not plausible. Electrochemical analysis showed that ash and sand are both negatively charged, showing that attachment of ash to sand and any resulting clogging is unlikely. Ash also had quite high saturated conductivity, and systems where ash was mixed in or lying on top of sand had similarly high hydraulic conductivity. Based on these various experiments, we cannot confirm the hypothesis that pore clogging by ash contributes to the frequently observed increase in post-fire runoff, at least for the medium to coarse sands

Obtention and characterization of ceramic products with addition of the mineral coal bottom ashes from thermoelectric power plants

International Nuclear Information System (INIS)

Kniess, C.T.; Prates, P.B.; Brys, M.; Martins, G.J.; Riella, H.G.; Bernardin, A.

2011-01-01

The physical, chemical and mineralogical properties of mineral coal bottom ash derived from thermoelectric power plants are compatible with various raw materials used in ceramic industries, which indicates a possibility of partial or fully substitution of raw materials by this residue. This work intends to obtain and characterize ceramic products with additions of different percentages of bottom ash coal. For this, was used a commercial ceramic body (CI) made by an industry in the state of Santa Catarina. The formulations of the ceramics products were obtained by the mixture design (planning network Simplex). The byproduct of coal bottom ash was found to be an attractive raw material source of SiO_2 and Al_2O_3 to obtain ceramic materials. Was demonstrated the possibility of developing a ceramic materials classified as semi-porous (6 10) with additions of up to 20% of coal bottom ash in the composition of the ceramic body. (author)

Assessment of mobility and bioavailability of contaminants in MSW incineration ash with aquatic and terrestrial bioassays.

Science.gov (United States)

Ribé, V; Nehrenheim, E; Odlare, M

2014-10-01

Incineration of municipal solid waste (MSW) is a waste treatment method which can be sustainable in terms of waste volume reduction as well as a source of renewable energy. In the process fly and bottom ash is generated as a waste material. The ash residue may vary greatly in composition depending on the type of waste incinerated and it can contain elevated levels of harmful contaminants such as heavy metals. In this study, the ecotoxicity of a weathered, untreated incineration bottom ash was characterized as defined by the H14 criterion of the EU Waste Framework Directive by means of an elemental analysis, leaching tests followed by a chemical analysis and a combination of aquatic and solid-phase bioassays. The experiments were conducted to assess the mobility and bioavailability of ash contaminants. A combination of aquatic and terrestrial bioassays was used to determine potentially adverse acute effects of exposure to the solid ash and aqueous ash leachates. The results from the study showed that the bottom ash from a municipal waste incineration plant in mid-Sweden contained levels of metals such as Cu, Pb and Zn, which exceeded the Swedish EPA limit values for inert wastes. The chemical analysis of the ash leachates showed high concentrations of particularly Cr. The leachate concentration of Cr exceeded the limit value for L/S 10 leaching for inert wastes. Filtration of leachates prior to analysis may have underestimated the leachability of complex-forming metals such as Cu and Pb. The germination test of solid ash and ash leachates using T. repens showed a higher inhibition of seedling emergence of seeds exposed to the solid ash than the seeds exposed to ash leachates. This indicated a relatively low mobility of toxicants from the solid ash into the leachates, although some metals exceeded the L/S 10 leaching limit values for inert wastes. The Microtox® toxicity test showed only a very low toxic response to the ash leachate exposure, while the D. magna

Chlorides behavior in raw fly ash washing experiments

International Nuclear Information System (INIS)

Zhu Fenfen; Takaoka, Masaki; Oshita, Kazuyuki; Kitajima, Yoshinori; Inada, Yasuhiro; Morisawa, Shinsuke; Tsuno, Hiroshi

2010-01-01

Chloride in fly ash from municipal solid waste incinerators (MSWIs) is one of the obstructive substances in recycling fly ash as building materials. As a result, we have to understand the behavior of chlorides in recycling process, such as washing. In this study, we used X-ray absorption near edge structure (XANES) and X-ray diffraction (XRD) to study the chloride behavior in washed residue of raw fly ash (RFA). We found that a combination of XRD and XANES, which is to use XRD to identify the situation of some compounds first and then process XANES data, was an effective way to explain the chlorides behavior in washing process. Approximately 15% of the chlorine in RFA was in the form of NaCl, 10% was in the form of KCl, 51% was CaCl 2 , and the remainder was in the form of Friedel's salt. In washing experiments not only the mole percentage but also the amount of soluble chlorides including NaCl, KCl and CaCl 2 decreases quickly with the increase of liquid to solid (L/S) ratio or washing frequency. However, those of insoluble chlorides decrease slower. Moreover, Friedel's salt and its related compound (11CaO.7Al 2 O 3 .CaCl 2 ) were reliable standards for the insoluble chlorides in RFA, which are strongly related to CaCl 2 . Washing of RFA promoted the release of insoluble chlorides, most of which were in the form of CaCl 2 .

Wet-dry cycles effect on ash water repellency. A laboratory experiment.

Science.gov (United States)

Pereira, Paulo; Cerdà, Artemi; Oliva, Marc; Mataix, Jorge; Jordán, Antonio

2014-05-01

In the immediate period after the fire, the ash layer has a strong influence on soil hydrological processes, as runoff, infiltration and erosion. Ash is very dynamic in the space and time. Until the first rainfall periods, ash is (re)distributed by the wind. After it can cover the soil surface, infiltrate or transported to other areas by water transport (Pereira et al., 2013a, b). This will have strong implications on nutrient redistribution and vegetation recovery. Ash layer may affect soil water repellency in different ways, depending on fire severity, soil properties and vegetation. Ash produced at low temperatures after low-severity burning is usually hydrophobic (Bodi et al., 2011, 2012). Wet-dry cycles have implications on ash physical and chemical properties, changing their effects in space and time. The aim of this study is to analyse the effects of fire temperature and severity on ash water repellency. Pinus sylvestris needles were collected in a Lithuania forest in Dzukija National Park (53º 54' N and 24º 22' E), transported to laboratory and washed with deionized water to remove soil particles and other residues. Needle samples were dried during 24 hours and exposed to different temperatures: 200, 300, 400 and 500 ºC, during 2 hours. Ash colour was analysed according to the Munsell Soil Color charts. Ash was black (10 YR 2/1) at 200 ºC, very dark grey (10YR 3/1) at 300 ºC, gray (10YR 5/1) at 400 ºC and light gray (10YR 7/1) at 500 ºC. Ten samples of ash released after each treatment were placed in plastic dishes (50 mm in diameter) in an amount enough to form a 5 mm thick layer, and ash water repellency was measured according to the Water Drop Penetration Test. Later, ash was carefully wetted with 15 ml of deionized water and placed in an oven during 4 days (96 hours), as in Bodí et al. (2012). This procedure was repeated 5 times in order to observe the effects of wet-dry cycles in ash water repellency. The results showed significant differences

Exploring evaluation to influence the quality of pulverized coal fly ash. Co-firing of biomass in a pulverized coal plant or mixing of biomass ashes with pulverized coal fly ash; Verkennende evaluatie kwaliteitsbeinvloeding poederkoolvliegas. Bijstoken van biomassa in een poederkoolcentrale of bijmenging van biomassa-assen met poederkoolvliegas

Energy Technology Data Exchange (ETDEWEB)

Van der Sloot, H.A.; Cnubben, P.A.J.P [ECN Schoon Fossiel, Petten (Netherlands)

2000-08-01

In this literature survey the consequences of co-firing of biomass and mixing of biomass ash with coal fly ash on the coal fly ash quality is evaluated. Biomass ash considered in this context is produced by gasification, pyrolysis or combustion in a fluidized bed. The irregular shape of biomass ash obtained from gasification, pyrolysis or combustion has a negative influence on the water demand in concrete applications of the coal fly ash resulting from mixing biomass ash and coal fly ash. In case of co-firing, high concentrations of elements capable of lowering the ash melting point (e.g., Ca and Mg) may lead to more ash agglomeration. This leads to a less favourable particle size distribution of the coal fly ash, which has a negative impact on the water demand in cement bound applications. Gasification, pyrolysis and combustion may lead to significant unburnt carbon levels (>10%). The unburnt carbon generally absorbs water and thus has a negative influence on the water demand in cement-bound applications. The contribution of biomass ash to the composition of coal fly ash will not be significantly different, whether the biomass is co-fired or whether the biomass ash is mixed off-line with coal fly ash. The limit values for Cl, SO4 and soluble salts can form a limitation for the use of coal fly ash containing biomass for cement-bound applications. As side effects of biomass co-firing, the level of constituents such as Na, K, Ca and Mg may lead to slagging and fouling of the boiler. In addition, a higher emission of flue gas contaminants As, Hg, F, Cl and Br may be anticipated in case more contaminated biomass streams are applied. This may also lead to a higher contamination level of gypsum produced from flue gas cleaning residues. Relatively clean biomass streams (clean wood, cacao shells, etc.) will hardly lead to critical levels of elements from a leaching point of view. More contaminated streams, such as sewage sludge, used and preserved wood, petcoke and RDF

Gasification reactivity and ash sintering behaviour of biomass feedstocks

Energy Technology Data Exchange (ETDEWEB)

Moilanen, A.; Nasrullah, M.

2011-12-15

Char gasification reactivity and ash sintering properties of forestry biomass feedstocks selected for large-scale gasification process was characterised. The study was divided into two parts: (1) Internal variation of the reactivity and the ash sintering of feedstocks. (2) Measurement of kinetic parameters of char gasification reactions to be used in the modelling of a gasifier. The tests were carried out in gases relevant to pressurized oxygen gasification, i.e. steam and carbon dioxide, as well as their mixtures with the product gases H{sub 2} and CO. The work was based on experimental measurements using pressurized thermobalance. In the tests, the temperatures were below 1000 deg C, and the pressure range was between 1 and 20 bar. In the first part, it was tested the effect of growing location, storage, plant parts and debarking method. The following biomass types were tested: spruce bark, pine bark, aspen bark, birch bark, forestry residue, bark feedstock mixture, stump chips and hemp. Thick pine bark had the lowest reactivity (instantaneous reaction rate 14%/min) and hemp the highest (250%/min); all other biomasses laid between these values. There was practically no difference in the reactivities among the spruce barks collected from the different locations. For pine bark, the differences were greater, but they were probably due to the thickness of the bark rather than to the growth location. For the spruce barks, the instantaneous reaction rate measured at 90% fuel conversion was 100%/min, for pine barks it varied between 14 and 75%/min. During storage, quite large local differences in reactivity seem to develop. Stump had significantly lower reactivity compared with the others. No clear difference in the reactivity was observed between barks obtained with the wet and dry debarking, but, the sintering of the ash was more enhanced for the bark from dry debarking. Char gasification rate could not be modelled in the gas mixture of H{sub 2}O + CO{sub 2} + H{sub 2

Ash study for biogas purification

International Nuclear Information System (INIS)

Juarez V, R. I.

2016-01-01

This work evaluates the ashes generated from the wood and coal combustion process of the thermoelectric plant in Petacalco, Guerrero (Mexico) in order to determine its viability as a filter in the biogas purification process. The ash is constituted by particles of morphology and different chemical properties, so it required a characterization of the same by different analytical techniques: as was scanning electron microscopy and X-ray diffraction, in order to observe the microstructure and determine the elemental chemical composition of the particles. Prior to the analysis, a set of sieves was selected to classify as a function of particle size. Four different types of ashes were evaluated: one generated by the wood combustion (wood ash) and three more of the Petacalco thermoelectric generated by the coal combustion (wet fly ash, dry fly ash and dry bottom ash). (Author)

Current Methods to Detoxify Fly Ash from Waste Incineration

Energy Technology Data Exchange (ETDEWEB)

Hallgren, Christine; Stroemberg, Birgitta [TPS Termiska Processer AB, Nykoeping (Sweden)

2004-07-01

vitrification, electric arc and melting in a secondary combustion chamber by adding coke as a heating source (coke bed melting furnaces) or residual carbon in the fly ash (Rotary surface melting furnace) are the most common methods. In general, vitrification processes require a high-energy input and are therefore relatively cost intensive. Locking the hazardous components into the matrix by a stabilization/solidification with cement is a common alternative to decontamination. Mixing the fly ash with cement or asphalt is widely used for the reuse of fly ash from coal incineration, but it requires careful attention to any leaching of heavy metals if applied to fly ash from waste incineration. Studies by mixing fly ash with cement at concentrations from 5 to 70 % showed, that in most cases an additional pretreatment step, e.g. washing in HNO{sub 3} solution, is necessary to receive acceptable leaching behaviour and required properties as building material. Related European regulations are currently pending. On the other hand, the use of fly ash as filler for asphalt does not require any pretreatment and is already commonly applied in some countries such as the Netherlands as a well-established method. Solvent extraction methods such as acidic extraction (3R-process) or combined basic and acidic extraction (MR-process) are also designed to remove the contaminants. The effectiveness of these methods is only moderate and a further thermal treatment is required to destroy the dioxins. These methods require relatively high amounts of chemicals and wastewater management. However, they are supposed to be relatively cost effective. Other treatment options that are being tested at laboratory scale such as microbiological treatment and supercritical extraction are optimistic but have no realistic practical relevance at this state.

Electrodialytic removal of heavy metals from different fly ashes. Influence of heavy metal speciation in the ashes

DEFF Research Database (Denmark)

Pedersen, Anne Juul; Ottosen, Lisbeth M.; Villumsen, Arne

2003-01-01

Electrodialytic Remediation has recently been suggested as a potential method for removal of heavy metals from fly ashes. In this work electrodialytic remediation of three different fly ashes, i.e. two municipal solid waste incinerator (MSWI) fly ashes and one wood combustion fly ash was studied...... in lab scale, and the results were discussed in relation to the expected heavy metal speciation in the ashes. In initial leaching experiments the pH-dependent desorption characteristics of the heavy metals Cd, Pb, Zn and Cu were analogous in the two MSWI ashes, and thus it was expected......-moval efficiencies were observed, especially for Pb and Zn. Cd, the sole heavy metal of environmental concern in the wood ash, was found more tightly bonded in this ash than in the two MSWI ashes. It was suggested that complex Cd-silicates are likely phases in the wood ash whereas more soluble, condensed phases...

Environmental assessment of incinerator residue utilisation

OpenAIRE

Toller, Susanna; Kärrman, Erik; Gustafsson, Jon Petter; Magnusson, Y.

2009-01-01

Incineration ashes may be treated either as a waste to be dumped in landfill, or as a resource that is suit able for re-use. In order to choose the best management scenario, knowledge is needed on the potential environmental impact that may be expected, including not only local, but also regional and global impact. In this study. A life cycle assessment (LCA) based approach Was Outlined for environmental assessment of incinerator residue utilisation, in which leaching of trace elements as wel...

Geochemical modeling and assessment of leaching from carbonated municipal solid waste incinerator (MSWI) fly ash.

Science.gov (United States)

Wang, Lei; Chen, Qi; Jamro, Imtiaz Ali; Li, Rundong; Li, Yanlong; Li, Shaobai; Luan, Jingde

2016-06-01

Municipal solid waste incinerator (MSWI) fly ashes are characterized by high calcium oxide (CaO) content. Carbon dioxide (CO2) adsorption by MSWI fly ash was discussed based on thermogravimetry (TG)/differential thermal analysis (DTA), minerology analysis, and adapting the Stenoir equation. TG/DTA analysis showed that the weight gain of the fly ash below 440 °C was as high as 5.70 %. An adapted Stenoir equation for MSWI fly ash was discussed. The chloride in MSWI fly ash has a major impact on CO2 adsorption by MSWI fly ash or air pollution control (APC) residues. Geochemical modeling of the critical trace elements copper (Cu), cadmium (Cd), zinc (Zn), lead (Pb), and antimony (Sb) before and after carbonation was performed using a thermodynamic equilibrium model for solubility and a surface complexation model for metal sorption. Leaching of critical trace elements was generally found to be strongly dependent on the degree of carbonation attained, and their solubility appeared to be controlled by several minerals. Adsorption on ferrum (Fe) and aluminum (Al) colloids was also responsible for removal of the trace elements Cd, Pb, and Sb. We used Hakanson's potential ecological risk index (HPERI) to evaluate the risk of trace element leaching in general. The results demonstrate that the ecological risk showed a V-shaped dependency on pH; the optimum pH of the carbonated fly ash was found to be 10.3-11, resulting from the optimum carbonation (liquid-to-solid (L/S) ratio = 0.25, carbonation duration = ∼30-48 h). The dataset and modeling results presented here provide a contribution to assessing the leaching behavior of MSWI fly ash under a wide range of conditions.

Novel synthesis and applications of Thiomer solidification for heavy metals immobilization in hazardous ASR/ISW thermal residue.

Science.gov (United States)

Baek, Jin Woong; Mallampati, Srinivasa Reddy; Park, Hung Suck

2016-03-01

The present paper reports the novel synthesis and application of Thiomer solidification for heavy metal immobilization in hazardous automobile shredder residues and industrial solid waste (ASR/ISW) thermal residues. The word Thiomer is a combination of the prefix of a sulfur-containing compound "Thio" and the suffix of "Polymer" meaning a large molecule compound of many repeated subunits. To immobilize heavy metals, either ASR/ISW thermal residues (including bottom and fly ash) was mixed well with Thiomer and heated at 140°C. After Thiomer solidification, approximately 91-100% heavy metal immobilization was achieved. The morphology and mineral phases of the Thiomer-solidified ASR/ISW thermal residue were characterized by field emission-scanning electron microscopy, energy dispersive X-ray spectroscopy and X-ray diffraction (XRD), which indicated that the amounts of heavy metals detectable on the ASR/ISW thermal residue surface decreased and the sulfur mass percent increased. XRD indicated that the main fraction of the enclosed/bound materials on the ASR/ISW residue contained sulfur associated crystalline complexes. The Thiomer solidified process could convert the heavy metal compounds into highly insoluble metal sulfides and simultaneously encapsulate the ASR/ISW thermal residue. These results show that the proposed method can be applied to the immobilization of ASR/ISW hazardous ash involving heavy metals. Copyright © 2015 Elsevier Ltd. All rights reserved.

First international ash marketing and technology conference

Energy Technology Data Exchange (ETDEWEB)

1978-01-01

A total of 42 papers were presented in sessions with the following headings: production and disposal of ash - an international review; environmental, health, safety, and legal aspects of ash handling; marketing of ash; development of new uses for ash; cementitious use of ash; ash in manufactured products; and geotechnical uses of ash.

Role of spent shale in oil shale processing and the management of environmental residues. Final technical report, January 1979-May 1980

Energy Technology Data Exchange (ETDEWEB)

Hines, A.L.

1980-08-15

The adsorption of hydrogen sulfide on retorted oil shale was studied at 10, 25, and 60/sup 0/C using a packed bed method. Equilibrium isotherms were calculated from the adsorption data and were modeled by the Langmuir, Freundlich, and Polanyi equations. The isosteric heat of adsorption was calculated at three adsorbent loadings and was found to increase with increased loading. A calculated heat of adsorption less than the heat of condensation indicated that the adsorption was primarily due to Van der Waals' forces. Adsorption capacities were also found as a function of oil shale retorting temperature with the maximum uptake occurring on shale that was retorted at 750/sup 0/C.

Properties of the fly ash from the Power Plant Dětmarovice from the point of view of their deposition in underground mines

Directory of Open Access Journals (Sweden)

Dirner Vojtech

2001-06-01

Full Text Available Mining for the Purposes of Disposal – Facilities, Requirements and Conceptions. Mining for the purposes of disposal can be instrumental in environmental protection in the future. Therefore the utilization of residues in the mining process has to be put into the foreground, whether they are a product of the mining activity itself or coming from other sources. It is possible to use the residual products as filling or building materials. Within the constantly increasing demand for building materials in the mines it is possible to combine the advantages that improve mine safety, rock mechanics and support with the secure long-term sealing of mineralized industrial residues in the lithosphere. Also the disposal of polluted, water-soluble and toxic or radioactive waste in a suitable geological formation underground can be realized ensuring long-term safety. This long-term safety is guaranteed by a multiple system of geological and technical barriers. The storage can b conducted in appropriate void space like chambers, caverns, drifts or boreholes with or without the opinion of retarding the material.Contribution is discussing the possibility of the deposition on fly ash produced by thermal power plants which are using low-grade brown coal as a fuel. Properties of fly ash were studied id detail on samples from Power Plant Dìtmarovice, northern Moravia.Results proved that fly ash can be deposited safely in underground.

Determining ash content in flotation wastes by means of the MPOF optical ash meter. [Poland

Energy Technology Data Exchange (ETDEWEB)

Sikora, T; Sliwa, J

1982-03-01

The paper evaluates an experimental unit of the MPOF optical ash meter, developed by the EMAG Research and Production Center for Electrical Engineering and Mining Automation. The MPOF, which is being tested at the coal preparation plant of the 30 lecia PRL mine, is the first system for continuous determination of ash content in flotation tailings developed in Poland. A block scheme of the system is given. It consists of a measuring head and electronic system which processes data supplied by the measuring head and calculates ash content. System operation is based on the principle of determining ash content in a mixture of coal and mineral wastes by measuring mixture reflectivity. Determining ash content in the mixture is possible as reflectivity coefficients for coal and ash are constant. Performance of the MPOF optical ash meter is evaluated; the results are shown in a table and a scheme. Measurement accuracy is satisfactory.

Ash Properties of Alternative Biomass

DEFF Research Database (Denmark)

Capablo, Joaquin; Jensen, Peter Arendt; Pedersen, Kim Hougaard

2009-01-01

analysis into three main groups depending upon their ash content of silica, alkali metal, and calcium and magnesium. To further detail the biomass classification, the relative molar ratio of Cl, S, and P to alkali were included. The study has led to knowledge on biomass fuel ash composition influence...... on ash transformation, ash deposit flux, and deposit chlorine content when biomass fuels are applied for suspension combustion....

Transformation of South African coal fly ash into ZSM-5 zeolite and its application as an MTO catalyst

CSIR Research Space (South Africa)

Missengue, RNM

2017-01-01

Full Text Available This study presents a way of using South African coal fly ash by extracting metals such as Al and Fe with concentrated sulphuric acid, and then using the solid residue as a feedstock for the synthesis of ZSM-5 zeolite. The percentage of aluminium...

Treatment of oil shale

Energy Technology Data Exchange (ETDEWEB)

Brown, H L

1922-07-04

To distill oil shale in lump form, it is fed as a continuous charge through an axially rotating externally heated retorting chamber, where the exposed surfaces of the lumps are gradually decomposed by destructive distillation, and light physical shocks are continuously administered to them, due to their tumbling-over motion and their contact with the ribs, to knock off the decomposing surfaces and present fresh surfaces for distillation. The vapors are withdrawn through a conduit, and the partially distilled lumps are fed through a shoot into a plurality of rotating externally heated retorts, similar in character to the first retort, from whence the vapors pass through a conduit to condensing apparatus, from which the permanent gases are withdrawn, and used for fuel in the distillation zone, while the residue is discharged into a water well. An auxiliary heating conduit, having a burner discharging into it, may be employed, while in some cases steam may be used if required. In two modifications, different arrangements of the retorts are shown, as well as means within the retorts for breaking up the lumps of shale.

Low temperature distillation

Energy Technology Data Exchange (ETDEWEB)

Vandegrift, J N; Postel, C

1929-04-09

To recover gas, oil tars, and coked residues by low temperature distillation from bituminous coals, lignites, oil shales, and the like, the raw material is fed from a hopper into a rotary retort which is zonally heated, the temperature being greatest at the discharge end. The material is heated first to a relatively low temperature, thereby removing the moisture and lighter volatiles which are withdrawn through a pipe by the suction of a pump, while the higher boiling point volatiles and fixed gases are withdrawn by suction through an outlet from the higher temperature zone. The vapors withdrawn from the opposite ends of the retort pass through separate vapor lines and condensers, and the suction in each end of the retort, caused by the pumps, is controlled by valves, which also control the location of the neutral point in the retort formed by said suction. Air and inert gas may be introduced into the retort from pipe and stack respectively through a pipe, and steam may be admitted into the high temperature zone through a pipe.

Quality and generation rate of solid residues in the boiler of a waste-to-energy plant

International Nuclear Information System (INIS)

Allegrini, E.; Boldrin, A.; Jansson, S.; Lundtorp, K.; Fruergaard Astrup, T.

2014-01-01

Highlights: • Ash was sampled at 10 different points of the boiler of a waste-to-energy plant. • Samples were analysed for the chemical composition, PCDD/F and leaching behaviour. • Enrichment trends of elements were investigated in relation to boiler conditions. • No significant differences were found between boiler ash samples. - Abstract: The Danish waste management system relies significantly on waste-to-energy (WtE) plants. The ash produced at the energy recovery section (boiler ash) is classified as hazardous waste, and is commonly mixed with fly ash and air pollution control residues before disposal. In this study, a detailed characterization of boiler ash from a Danish grate-based mass burn type WtE was performed, to evaluate the potential for improving ash management. Samples were collected at 10 different points along the boiler's convective part, and analysed for grain size distribution, content of inorganic elements, polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD and PCDF), and leaching of metals. For all samples, PCDD and PCDF levels were below regulatory limits, while high pH values and leaching of e.g. Cl were critical. No significant differences were found between boiler ash from individual sections of the boiler, in terms of total content and leaching, indicating that separate management of individual ash fractions may not provide significant benefits

Quality and generation rate of solid residues in the boiler of a waste-to-energy plant

Energy Technology Data Exchange (ETDEWEB)

Allegrini, E., E-mail: elia@env.dtu.dk [Technical University of Denmark, Department of Environmental Engineering, Building 115, Lyngby 2800 (Denmark); Boldrin, A. [Technical University of Denmark, Department of Environmental Engineering, Building 115, Lyngby 2800 (Denmark); Jansson, S. [Umeå University, Department of Chemistry, Umeå SE-901 87 (Sweden); Lundtorp, K. [Babcock and Wilcox Vølund A/S, Göteborg (Sweden); Fruergaard Astrup, T. [Technical University of Denmark, Department of Environmental Engineering, Building 115, Lyngby 2800 (Denmark)

2014-04-01

Highlights: • Ash was sampled at 10 different points of the boiler of a waste-to-energy plant. • Samples were analysed for the chemical composition, PCDD/F and leaching behaviour. • Enrichment trends of elements were investigated in relation to boiler conditions. • No significant differences were found between boiler ash samples. - Abstract: The Danish waste management system relies significantly on waste-to-energy (WtE) plants. The ash produced at the energy recovery section (boiler ash) is classified as hazardous waste, and is commonly mixed with fly ash and air pollution control residues before disposal. In this study, a detailed characterization of boiler ash from a Danish grate-based mass burn type WtE was performed, to evaluate the potential for improving ash management. Samples were collected at 10 different points along the boiler's convective part, and analysed for grain size distribution, content of inorganic elements, polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD and PCDF), and leaching of metals. For all samples, PCDD and PCDF levels were below regulatory limits, while high pH values and leaching of e.g. Cl were critical. No significant differences were found between boiler ash from individual sections of the boiler, in terms of total content and leaching, indicating that separate management of individual ash fractions may not provide significant benefits.

An environmentally-friendly vacuum reduction metallurgical process to recover germanium from coal fly ash

Energy Technology Data Exchange (ETDEWEB)

Zhang, Lingen; Xu, Zhenming, E-mail: zmxu@sjtu.edu.cn

2016-07-15

Highlights: • An environmental friendly vacuum reduction metallurgical process is proposed. • Rare and valuable metal germanium from coal fly ash is recycled. • Residues are not a hazardous material and can be further recycled. • A germanium recovery ratio of 94.64% is obtained in pilot scale experiments. - Abstract: The demand for germanium in the field of semiconductor, electronics, and optical devices is growing rapidly; however, the resources of germanium are scarce worldwide. As a secondary material, coal fly ash could be further recycled to retrieve germanium. Up to now, the conventional processes to recover germanium have two problems as follows: on the one hand, it is difficult to be satisfactory for its economic and environmental effect; on the other hand, the recovery ratio of germanium is not all that could be desired. In this paper, an environmentally-friendly vacuum reduction metallurgical process (VRMP) was proposed to recover germanium from coal fly ash. The results of the laboratory scale experiments indicated that the appropriate parameters were 1173 K and 10 Pa with 10 wt% coke addition for 40 min, and recovery ratio germanium was 93.96%. On the basis of above condition, the pilot scale experiments were utilized to assess the actual effect of VRMP for recovery of germanium with parameter of 1473 K, 1–10 Pa and heating time 40 min, the recovery ratio of germanium reached 94.64%. This process considerably enhances germanium recovery, meanwhile, eliminates much of the water usage and residue secondary pollution compared with other conventional processes.

A new quantification method based on SEM-EDS to assess fly ash composition and study the reaction of its individual components in hydrating cement paste

Energy Technology Data Exchange (ETDEWEB)

Durdziński, Paweł T., E-mail: pawel.durdzinski@gmail.com [Laboratory of Construction Materials, École Polytechnique Fédérale de Lausanne (EPFL), Station 12, CH-1015 Lausanne (Switzerland); Dunant, Cyrille F. [Laboratory of Construction Materials, École Polytechnique Fédérale de Lausanne (EPFL), Station 12, CH-1015 Lausanne (Switzerland); Haha, Mohsen Ben [HeidelbergCement Technology Center GmbH (HeidelbergCement AG), Rohrbacher Str. 95, 69181 Leimen (Germany); Scrivener, Karen L. [Laboratory of Construction Materials, École Polytechnique Fédérale de Lausanne (EPFL), Station 12, CH-1015 Lausanne (Switzerland)

2015-07-15

Calcareous fly ashes are high-potential reactive residues for blended cements, but their qualification and use in concrete are hindered by heterogeneity and variability. Current characterization often fails to identify the dominant, most reactive, amorphous fraction of the ashes. We developed an approach to characterize ashes using electron microscopy. EDS element composition of millions of points is plotted in a ternary frequency plot. A visual analysis reveals number and ranges of chemical composition of populations: silicate, calcium-silicate, aluminosilicate, and calcium-rich aluminosilicate. We quantified these populations in four ashes and followed their hydration in two Portland-ash systems. One ash reacted at a moderate rate: it was composed of 70 vol.% of aluminosilicates and calcium-silicates and reached 60% reaction at 90 days. The other reacted faster, reaching 60% at 28 days due to 55 vol.% of calcium-rich aluminosilicates, but further reaction was slower and 15 vol.% of phases, the silica-rich ones, did not react.

A new quantification method based on SEM-EDS to assess fly ash composition and study the reaction of its individual components in hydrating cement paste

International Nuclear Information System (INIS)

Durdziński, Paweł T.; Dunant, Cyrille F.; Haha, Mohsen Ben; Scrivener, Karen L.

2015-01-01

Calcareous fly ashes are high-potential reactive residues for blended cements, but their qualification and use in concrete are hindered by heterogeneity and variability. Current characterization often fails to identify the dominant, most reactive, amorphous fraction of the ashes. We developed an approach to characterize ashes using electron microscopy. EDS element composition of millions of points is plotted in a ternary frequency plot. A visual analysis reveals number and ranges of chemical composition of populations: silicate, calcium-silicate, aluminosilicate, and calcium-rich aluminosilicate. We quantified these populations in four ashes and followed their hydration in two Portland-ash systems. One ash reacted at a moderate rate: it was composed of 70 vol.% of aluminosilicates and calcium-silicates and reached 60% reaction at 90 days. The other reacted faster, reaching 60% at 28 days due to 55 vol.% of calcium-rich aluminosilicates, but further reaction was slower and 15 vol.% of phases, the silica-rich ones, did not react

Size fractionation of waste-to-energy boiler ash enables separation of a coarse fraction with low dioxin concentrations.

Science.gov (United States)

Weidemann, E; Allegrini, E; Fruergaard Astrup, T; Hulgaard, T; Riber, C; Jansson, S

2016-03-01

Polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/F) formed in modern Waste-to-Energy plants are primarily found in the generated ashes and air pollution control residues, which are usually disposed of as hazardous waste. The objective of this study was to explore the occurrence of PCDD/F in different grain size fractions in the boiler ash, i.e. ash originating from the convection pass of the boiler. If a correlation between particle size and dioxin concentrations could be found, size fractionation of the ashes could reduce the total amount of hazardous waste. Boiler ash samples from ten sections of a boiler's convective part were collected over three sampling days, sieved into three different size fractions - 0.355 mm - and analysed for PCDD/F. The coarse fraction (>0.355 mm) in the first sections of the horizontal convection pass appeared to be of low toxicity with respect to dioxin content. While the total mass of the coarse fraction in this boiler was relatively small, sieving could reduce the amount of ash containing toxic PCDD/F by around 0.5 kg per tonne input waste or around 15% of the collected boiler ash from the convection pass. The mid-size fraction in this study covered a wide size range (0.09-0.355 mm) and possibly a low toxicity fraction could be identified by splitting this fraction into more narrow size ranges. The ashes exhibited uniform PCDD/F homologue patterns which suggests a stable and continuous generation of PCDD/F. Copyright © 2016 Elsevier Ltd. All rights reserved.

Biotic and abiotic factors affect green ash volatile production and emerald ash borer adult feeding preference.

Science.gov (United States)

Chen, Yigen; Poland, Therese M

2009-12-01

The emerald ash borer, Agrilus planipennis Fairmaire (Coleoptera: Buprestidae), is an exotic woodborer first detected in 2002 in Michigan and Ontario and is threatening the ash resource in North America. We examined the effects of light exposure and girdling on green ash (Fraxinus pennsylvanica Marsh) volatile production, and effects of light exposure, girdling, and leaf age on emerald ash borer adult feeding preferences and phototaxis. Green ash seedlings grown under higher light exposure had lower amounts of three individual volatile compounds, (Z)-3-hexenol, (E)-beta-ocimene, and (Z,E)-alpha-farnesene, as well as the total amount of six detected volatile compounds. Girdling did not affect the levels of these volatiles. Emerald ash borer females preferred mature leaves, leaves from girdled trees, and leaves grown in the sun over young leaves, leaves from nongirdled trees, and leaves grown in the shade, respectively. These emerald ash borer preferences were most likely because of physical, nutritional, or biochemical changes in leaves in response to the different treatments. Emerald ash borer females and males showed positive phototaxis in laboratory arenas, a response consistent with emerald ash borer preference for host trees growing in sunlight.

10 Risk to Ash from Emerald Ash Borer: Can Biological Control Prevent the Loss of Ash Stands

Science.gov (United States)

Ash trees were once relatively free of serious, major diseases and insect pests in North America until the arrival of EAB, which was first detected in North America in Michigan in 2002. As of February 2014, EAB had been detected in 22 U.S. states and two Canadian provinces, killing millions of ash ...

Processed bottom ash for replacing fine aggregate in making high-volume fly ash concrete

OpenAIRE

Antoni; Sulistio Aldi Vincent; Wahjudi Samuel; Hardjito Djwantoro; Hardjito Djwantoro

2017-01-01

Bottom ash is a coal plant by-product that is abundant and underutilized. There is the potential use of bottom ash as a fine aggregate replacement in concrete mixtures; however, the problems of water absorption and uniformity of quality of the material need to be overcome first. In this study, bottom ash was treated by sieve separation and pounding to smaller particle size for use as a sand substitute. The physical and chemical characteristics of bottom ash were tested after treatment includi...

Oil sludge treatment using thermal and ash vitrification technology

International Nuclear Information System (INIS)

Rohyiza Baan; Sharifah Aishah, S.A.K.; Mohamad Puad Abu; Mohd Abdul Wahab Yusof

2010-01-01

In this paper, an experimental study of crude oil sludge terminal for volume reduction and radionuclide stability was treated by using integrated thermal treatment system. The pre-thermal treatment of oil sludge was carried out in fluidized bed combustor at temperature 500 degree Celsius, and then the ash produced from that process was vitrified in high temperature furnace at temperature above 1000 degree Celsius. The main contents of oil sludge are composed of 80% carbon, 11% sulphur, 50% volatile matter and 30% ash. The high heating value was 35,722 kJ/ kg. Analysis by gamma spectrometer was showed the radionuclide as Ra-226 (52.23 Bq/ kg), Ra-228 (47.48 Bq/ kg), K-40 (172.55 Bq/ kg), whereas analysis by neutron activation analysis (NAA) for U (0.5 μg/ g) and Th (0.5 μg/ g) was present in low concentration. Trace elements as Ba, Cd, Cr, Hg, As, Pb, Al, Zn, Ni was determine by using ICPMS. Thermal analysis has shown loss of mass and residual decomposition in the TG and DTA curves. The concentration of radionuclide in ash from fluidized bed combustor process was increased for Ra-226 (264.27 Bq/ kg) and Ra-228 (253.77 Bq/ kg). The slag was produced from ash vitrification process was characterized by X-ray fluorescence (XRF) and showed that silica oxide and potassium oxide were found. The slag characterization by X-ray diffraction (XRD) showed that slag composed of crystalline. The toxicity characteristic leaching procedure (TCLP) test showed that the slag resulted in very low leachability of heavy metals. Most of the toxic metals are fixed in the vitrification process and the leachate values meet the standard level of Malaysian Department of Environmental (DOE) of hazardous materials. The average concentration of each element varied between 1.5-14.0 mg/ kg. (author)

Characterization of metals released from coal fly ash during dredging at the Kingston ash recovery project.

Science.gov (United States)

Bednar, A J; Averett, D E; Seiter, J M; Lafferty, B; Jones, W T; Hayes, C A; Chappell, M A; Clarke, J U; Steevens, J A

2013-09-01

A storage-pond dike failure occurred on December 22, 2008 at the Tennessee Valley Authority Kingston Fossil Plant resulting in the release of over 4million cubic meters (5million cubic yards) of fly ash. Approximately half of the released ash was deposited in the main channel of the Emory River, Tennessee, USA. Remediation efforts of the Emory River focused on hydraulic dredging, as well as mechanical excavation in targeted areas. However, agitation of the submerged fly ash during hydraulic dredging introduces river water into the fly ash material, which could promote dissolution and desorption of metals from the solid fly ash material. Furthermore, aeration of the dredge slurry could alter the redox state of metals in the fly ash material and thereby change their sorption, mobility, and toxicity properties. The research presented here focuses on the concentrations and speciation of metals during the fly ash recovery from the Emory River. Our results indicate that arsenite [As(III)] released from the fly ash material during dredging was slowly oxidized to arsenate [As(V)] in the slurry recovery system with subsequent removal through precipitation or sorption reactions with suspended fly ash material. Concentrations of other dissolved metals, including iron and manganese, also generally decreased in the ash recovery system prior to water discharge back to the river. Published by Elsevier Ltd.

Prospects for ash pond reclamation

Energy Technology Data Exchange (ETDEWEB)

Shyyam, A.K.; Shukla, K.S.; Agrawal, D. (National Thermal Power Corporation Ltd., New Delhi (India))

1993-01-01

A typical modern coal fired station in India burns 0.7 t/MWh of coal and consequently generates ash at 0.245 t/MWh. The physical nature of ash, low available concentrations of certain plant nutrients and the presence of phytotoxic trace elements render fly ash marginally adequate for plant growth. As fly ash itself was thought to be an inappropriate growth medium for plants, regulators decided that a soil cover is mandatory. There is ample data to suggest that the attributes of fly ash detrimental to plant growth can be ameliorated, allowing the establishment of vegetation directly on fly ash surfaces. The natural revegetation of fly ash disposal sites has been reported in the world. The natural vegetation pioneered by Cynodon at different stages of ecological succession and comprising of species such as [ital Calotropis gigantea], [ital Lippia nodiflora], [ital Ipomea, cornea], [ital Xanthium parviflorum] has been noted at one of the NTPC projects, in Badarpur Thermal Power Station. Since natural reclamation is a time-consuming process, experimental trials of growing some species over the temporary ash lagoon directly (without soil cover) were carried out at Ramagundam Super Thermal Power Project (RSTPP) of NTPC, in South India to achieve faster results than the natural process. 6 refs., 8 figs.

Radioisotope conveyor ash meter

International Nuclear Information System (INIS)

Savelov, V.D.

1994-01-01

Radioisotope conveyor ash meter realizes persistent measuring of ashiness of coal and products of its enrichment on the belt conveyor without contact. The principle of ash meter acting is based on functional dependence of the gamma radiation flows backscattering intensity of radioisotope sources from the ash volume content in the controlled fuel. Facility consists from the ashiness transducer and the processing and control device

Chlorides behavior in raw fly ash washing experiments.

Science.gov (United States)

Zhu, Fenfen; Takaoka, Masaki; Oshita, Kazuyuki; Kitajima, Yoshinori; Inada, Yasuhiro; Morisawa, Shinsuke; Tsuno, Hiroshi

2010-06-15

Chloride in fly ash from municipal solid waste incinerators (MSWIs) is one of the obstructive substances in recycling fly ash as building materials. As a result, we have to understand the behavior of chlorides in recycling process, such as washing. In this study, we used X-ray absorption near edge structure (XANES) and X-ray diffraction (XRD) to study the chloride behavior in washed residue of raw fly ash (RFA). We found that a combination of XRD and XANES, which is to use XRD to identify the situation of some compounds first and then process XANES data, was an effective way to explain the chlorides behavior in washing process. Approximately 15% of the chlorine in RFA was in the form of NaCl, 10% was in the form of KCl, 51% was CaCl(2), and the remainder was in the form of Friedel's salt. In washing experiments not only the mole percentage but also the amount of soluble chlorides including NaCl, KCl and CaCl(2) decreases quickly with the increase of liquid to solid (L/S) ratio or washing frequency. However, those of insoluble chlorides decrease slower. Moreover, Friedel's salt and its related compound (11CaO.7Al(2)O(3).CaCl(2)) were reliable standards for the insoluble chlorides in RFA, which are strongly related to CaCl(2). Washing of RFA promoted the release of insoluble chlorides, most of which were in the form of CaCl(2). Copyright 2010 Elsevier B.V. All rights reserved.

Get immersed and black in fire ash world. Field Wildgeographers experience.

Science.gov (United States)

Pereira, Paulo; Cerdà, Artemi; Misiune, Ieva; Jordan, Antonio

2015-04-01

Ash is the footprint left by the fire. This residue is very important to landscape recover and is an important source of soil protection after the fire. Get immersed in fire ash world is the same thing of get dirty and do not be recognizable in a fire affected area. To measure ash in the field we have to be careful where to step, how to do the experimental design, collect samples and find with accuracy the places measured before. A good methodology is needed in design field experiments, collect ash samples and monitoring ash evolution (Cerdà and Doerr, 2008; Bodi et al., 2014; Pereira and Ubeda, 2010; Pereira et al. 2011; 2012, 2013, 2014, 2015). The objective of this work is to share with the Avatar world the methodologies used when wildgeographers get immersed in fire ash world, including: 1) Identify the best study area 2) Experimental design 3) Sample collection 4) Get dirty and have fun in the field 5) Laboratory, Statistical and spatial analysis Acknoledgements The author are thankful for the support of the projects POSTFIRE (Soil quality, erosion control and plant cover recovery under different post-fire management scenarios, CGL2013-47862-C2-1-R) funded by the Spanish Ministry of Economy and Competitiveness; GL2008-02879/BTE, LEDDRA 243857, RECARE (Preventing and Remediating Degradation of Soils in Europe Through Land Care, FP7-ENV-2013-TWO STAGE), funded by the European Commission; and for the COST action ES1306 (Connecteur: Connecting European Connectivity Research), FUEGORED (Spanish Network of Forest Fire Effects on Soils, http://grupo.us.es/fuegored/) and to Comissionat per a Universitats i Recerca del DIUE de la Generalitat de Catalunya. References Bodi, M., Martin, D.A., Santin, C., Balfour, V., Doerr, S.H., Pereira, P., Cerda, A., Mataix-Solera, J. (2014) Wildland fire ash: production, composition and eco-hydro-geomorphic effects. Earth-Science Reviews, 130, 103-127. Cerdà, A. y Doerr, S.H. 2008. The effect of ash and needle cover on surface

Bioleaching of trace metals from coal ash using local isolate from coal ash ponds

Directory of Open Access Journals (Sweden)

Pangayao Denvert

2018-01-01

Full Text Available Bioleaching of chromium, copper, manganese and zinc from coal ash were investigated using isolates from coal ash ponds particularly Psuedomonas spp. Six (6 different coal ash ponds were examined however, after initial screening Psuedomonas spp. were only present in three (3 coal ash ponds. Among the three coal ash ponds, results showed that eight (8 putative Pseudomonas spp. isolates were present that were identified using the Polymerase Chain Reaction (PCR. Using the eight putative Pseudomonas spp. for bioleaching at optimum conditions and 15 days, the pH value ranges from 8.26 to 8.84 which was basic in nature. Moreover, the maximum metal leached were 8.04% Cr, 12.05% Cu, 4.34% Mn and 10.63% Zn.

Soil quality in a cropland soil treated with wood ash containing charcoal

Science.gov (United States)

Omil, Beatriz; Balboa, Miguel A.; Fonturbel, M. Teresa; Gartzia-Bengoetxea, Nahia; Arias-González, Ander; Vega, Jose A.; Merino, Agustin

2014-05-01

The strategy of the European Union "Europe 2020" states that by 2020, 20% of final energy consumption must come from renewables. In this scenario, there is an increasing use of biomass utilization for energy production. Indeed, it is expected that the production of wood-ash will increase in coming years. Wood ash, a mixture of ash and charcoal, generated as a by-product of biomass combustion in power plants, can be applied to soil to improve the soil quality and crop production. Since the residue contains significant content of charcoal, the application of mixed wood ash may also improve the SOM content and soil quality in the long term, in soils degraded as a consequence of intensive management. The objective of this study was asses the changes in SOM quality and soil properties in a degraded soils treated with wood ash containing charcoal. The study was carried out in a field devoted to cereal crops during the last decades. The soil was acidic (pH 4.5) with a low SOC content (3 %) and fine texture. The experiment was based on a randomised block design with four replicates. Each block included the following four treatments: Control, 16 Mg fly wood ash ha-1, 16 Mg mixed wood ash ha-1 (16 Mg) and 32 Mg mixed wood ash ha-1 (32 Mg). The application was carried out once. The ash used in the study was obtained from a thermal power plant and was mainly derived from the combustion of Pinus radiata bark and branches. The wood ash is highly alkaline (pH= 10), contains 10 % of highly condensed black carbon (atomic H/C ratio solid state 13C CPMAS NMR and Differential Scanning Calorimetry (DSC). These techniques were applied in bulk samples and aggregates of different sizes. The changes in microbial activity were studied by analysis of microbial biomass C and basal respiration. The soil bacterial community was studied by the Biolog method. Several physical properties, such soil aggregate distribution, hydraulic conductivity and available water contente were also determined

Optimizing and Characterizing Geopolymers from Ternary Blend of Philippine Coal Fly Ash, Coal Bottom Ash and Rice Hull Ash

Directory of Open Access Journals (Sweden)

Martin Ernesto Kalaw

2016-07-01

Full Text Available Geopolymers are inorganic polymers formed from the alkaline activation of amorphous alumino-silicate materials resulting in a three-dimensional polymeric network. As a class of materials, it is seen to have the potential of replacing ordinary Portland cement (OPC, which for more than a hundred years has been the binder of choice for structural and building applications. Geopolymers have emerged as a sustainable option vis-à-vis OPC for three reasons: (1 their technical properties are comparable if not better; (2 they can be produced from industrial wastes; and (3 within reasonable constraints, their production requires less energy and emits significantly less CO2. In the Philippines, the use of coal ash, as the alumina- and silica- rich geopolymer precursor, is being considered as one of the options for sustainable management of coal ash generation from coal-fired power plants. However, most geopolymer mixes (and the prevalent blended OPC use only coal fly ash. The coal bottom ash, having very few applications, remains relegated to dumpsites. Rice hull ash, from biomass-fired plants, is another silica-rich geopolymer precursor material from another significantly produced waste in the country with only minimal utilization. In this study, geopolymer samples were formed from the mixture of coal ash, using both coal fly ash (CFA and coal bottom ash (CBA, and rice hull ash (RHA. The raw materials used for the geopolymerization process were characterized using X-ray fluorescence spectroscopy (XRF for elemental and X-ray diffraction (XRD for mineralogical composition. The raw materials’ thermal stability and loss on ignition (LOI were determined using thermogravimetric analysis (TGA and reactivity via dissolution tests and inductively-coupled plasma mass spectrometry (ICP analysis. The mechanical, thermal and microstructural properties of the geopolymers formed were analyzed using compression tests, Fourier transform infra-red spectroscopy (FTIR

Optimizing and Characterizing Geopolymers from Ternary Blend of Philippine Coal Fly Ash, Coal Bottom Ash and Rice Hull Ash.

Science.gov (United States)

Kalaw, Martin Ernesto; Culaba, Alvin; Hinode, Hirofumi; Kurniawan, Winarto; Gallardo, Susan; Promentilla, Michael Angelo

2016-07-15

Geopolymers are inorganic polymers formed from the alkaline activation of amorphous alumino-silicate materials resulting in a three-dimensional polymeric network. As a class of materials, it is seen to have the potential of replacing ordinary Portland cement (OPC), which for more than a hundred years has been the binder of choice for structural and building applications. Geopolymers have emerged as a sustainable option vis-à-vis OPC for three reasons: (1) their technical properties are comparable if not better; (2) they can be produced from industrial wastes; and (3) within reasonable constraints, their production requires less energy and emits significantly less CO₂. In the Philippines, the use of coal ash, as the alumina- and silica- rich geopolymer precursor, is being considered as one of the options for sustainable management of coal ash generation from coal-fired power plants. However, most geopolymer mixes (and the prevalent blended OPC) use only coal fly ash. The coal bottom ash, having very few applications, remains relegated to dumpsites. Rice hull ash, from biomass-fired plants, is another silica-rich geopolymer precursor material from another significantly produced waste in the country with only minimal utilization. In this study, geopolymer samples were formed from the mixture of coal ash, using both coal fly ash (CFA) and coal bottom ash (CBA), and rice hull ash (RHA). The raw materials used for the geopolymerization process were characterized using X-ray fluorescence spectroscopy (XRF) for elemental and X-ray diffraction (XRD) for mineralogical composition. The raw materials' thermal stability and loss on ignition (LOI) were determined using thermogravimetric analysis (TGA) and reactivity via dissolution tests and inductively-coupled plasma mass spectrometry (ICP) analysis. The mechanical, thermal and microstructural properties of the geopolymers formed were analyzed using compression tests, Fourier transform infra-red spectroscopy (FTIR), scanning

Effects of the addition of oil shale ash and coal ash on physic-chemical properties of CPJ45 cement

Directory of Open Access Journals (Sweden)

Nabih K.

2014-04-01

Full Text Available We focused our research on recycling industrial wastes, fly ash (F.A, bottom ash (B.A and oil shale ash (S.A in cement production. The study concerns physico-chemical characterization of these products and the influence of their addition on the mechanical proprieties of the CPJ45 cement. XRF allowed us to rank the three additives used according to their contents on major oxides. Coal ashes belong to the class F, and thus possess poozzolanic properties and oil shale ash belongs to the class C and possesses hydraulic and poozolanic properties. The crystalline phases constituting each ash were analysed by XRD. We observe in bottom ash the presence of quartz and mullite. The same crystals are found in fly ash with hematite and magnetite. Oil shale ash is composed of quartz, anhydrite, gehlenite, wollastonite and periclase. The microstructures of fly ash and bottom ash were studied using SEM. The bottom ash was composed respectively of fine particles that are generally irregularly shaped, their dimensions are between 5 and 28μm and of big particles(300 μm. The EDX analysis coupled with an electronic microscope provided some information about the major elements that constitute our samples. The dehydrations of anhydrous and three days hydrated cement were examined by DSC. For hydrated cements we noticed endothermic peaks related to the dehydration of CSH, CH and decomposition of carbonates. The study of the mechanical properties of CPJ45 cement by adding different proportions of fly ash, bottom ash and oil shale ash helped clarifying the percentage of ash that leaded to improve the 28 days mechanical strength. The results show that the cements studied have their maximum mechanical resistance with the addition at 7% of fly ash or 10% of oil shale ash.

Fly ash dynamics in soil-water systems

International Nuclear Information System (INIS)

Sharma, S.; Fulekar, M.H.; Jayalakshmi, C.P.

1989-01-01

Studies regarding the effluents and coal ashes (or fly ash) resulting from coal burning are numerous, but their disposal and interactions with the soil and water systems and their detailed environmental impact assessment with concrete status reports on a global scale are scanty. Fly ash dynamics in soil and water systems are reviewed. After detailing the physical composition of fly ash, physicochemical changes in soil properties due to fly ash amendment are summarized. Areas covered include texture and bulk density, moisture retention, change in chemical equilibria, and effects of fly ash on soil microorganisms. Plant growth in amended soils is discussed, as well as plant uptake and accumulation of trace elements. In order to analyze the effect of fly ash on the physicochemical properties of water, several factors must be considered, including surface morphology of fly ash, pH of the ash sluice water, pH adjustments, leachability and solubility, and suspended ash and settling. The dynamics of fly ash in water systems is important due to pollution of groundwater resources from toxic components such as trace metals. Other factors summarized are bioaccumulation and biomagnification, human health effects of contaminants, and the impact of radionuclides in fly ash. Future research needs should focus on reduction of the environmental impact of fly ash and increasing utilization of fly ash as a soil amendment. 110 refs., 2 figs., 10 tabs

Use of rice straw ash as substitute of feldspar in triaxial porcelain

OpenAIRE

Guzmán, Álvaro; Delvasto, Silvio; Sánchez, Enrique; Amigó Borrás, Vicente

2013-01-01

[EN] The substitution of raw materials for processing high energy consumption materials by agricultural and agro-industrial wastes causes a positive impacts on the environment preservation. One of these residues is rice straw, which according to FAO estimation, its annual production is about 600 million tons. In this research was studied the use of rice straw ash (RSA) as substitute of the use of feldspar in the whiteware production. Clay-feldspar-quartz porcelains are referred to...

Leaching optimization of municipal solid waste incineration ash for resource recovery: A case study of Cu, Zn, Pb and Cd.

Science.gov (United States)

Tang, Jinfeng; Steenari, Britt-Marie

2016-02-01

Ash from municipal solid waste incineration (MSWI) may be quite cumbersome to handle. Some ash fractions contain organic pollutants, such as dioxins, as well as toxic metals. Additionally, some of the metals have a high value and are considered as critical to the industry. Recovery of copper, zinc and lead from MSWI ashes, for example, will not only provide valuable metals that would otherwise be landfilled but also give an ash residue with lower concentrations of toxic metals. In this work, fly ash and bottom ash from an MSWI facility was used for the study and optimization of metal leaching using different solutions (nitric acid, hydrochloric acid and sulfuric acid) and parameters (temperature, controlled pH value, leaching time, and liquid/solid ratio). It was found that hydrochloric acid is relatively efficient in solubilizing copper (68.2±6.3%) and zinc (80.8±5.3%) from the fly ash in less than 24h at 20°C. Efficient leaching of cadmium and lead (over 92% and 90% respectively) was also achieved. Bottom ash from the same combustion unit was also characterized and leached using acid. The metal yields were moderate and the leachates had a tendency to form a gelatinous precipitate, which indicates that the solutions were actually over-saturated with respect to some components. This gel formation will cause problems for further metal purification processes, e.g. solvent extraction. Copyright © 2015 Elsevier Ltd. All rights reserved.

Fly ash quality and utilization

Energy Technology Data Exchange (ETDEWEB)

Barta, L.E.; Lachner, L.; Wenzel, G.B. [Inst. for Energy, Budapest (Hungary); Beer, M.J. [Massachusetts Inst. of Technology, Cambridge, MA (United States)

1995-12-01

The quality of fly ash is of considerable importance to fly ash utilizers. The fly ash puzzolanic activity is one of the most important properties that determines the role of fly ash as a binding agent in the cementing process. The puzzolanic activity, however is a function of fly ash particle size and chemical composition. These parameters are closely related to the process of fly ash formation in pulverized coal fired furnaces. In turn, it is essential to understand the transformation of mineral matter during coal combustion. Due to the particle-to-particle variation of coal properties and the random coalescence of mineral particles, the properties of fly ash particles e.g. size, SiO{sub 2} content, viscosity can change considerably from particle to particle. These variations can be described by the use of the probability theory. Since the mean values of these randomly changing parameters are not sufficient to describe the behavior of individual fly ash particles during the formation of concrete, therefore it is necessary to investigate the distribution of these variables. Examples of these variations were examined by the Computer Controlled Scanning Electron Microscopy (CCSEM) for particle size and chemical composition for Texas lignite and Eagel Butte mineral matter and fly ash. The effect of combustion on the variations of these properties for both the fly ash and mineral matter were studied by using a laminar flow reactor. It is shown in our paper, that there are significant variations (about 40-50% around the mean values) of the above-listed properties for both coal samples. By comparing the particle size and chemical composition distributions of the mineral matter and fly ash, it was possible to conclude that for the Texas lignite mineral matter, the combustion did not effect significantly the distribution of these properties, however, for the Eagel Butte coal the combustion had a major impact on these mineral matter parameters.

Ash cloud aviation advisories

Energy Technology Data Exchange (ETDEWEB)

Sullivan, T.J.; Ellis, J.S. [Lawrence Livermore National Lab., CA (United States); Schalk, W.W.; Nasstrom, J.S. [EG and G, Inc., Pleasanton, CA (United States)

1992-06-25

During the recent (12--22 June 1991) Mount Pinatubo volcano eruptions, the US Air Force Global Weather Central (AFGWC) requested assistance of the US Department of Energy`s Atmospheric Release Advisory Capability (ARAC) in creating volcanic ash cloud aviation advisories for the region of the Philippine Islands. Through application of its three-dimensional material transport and diffusion models using AFGWC meteorological analysis and forecast wind fields ARAC developed extensive analysis and 12-hourly forecast ash cloud position advisories extending to 48 hours for a period of five days. The advisories consisted of ``relative`` ash cloud concentrations in ten layers (surface-5,000 feet, 5,000--10,000 feet and every 10,000 feet to 90,000 feet). The ash was represented as a log-normal size distribution of 10--200 {mu}m diameter solid particles. Size-dependent ``ashfall`` was simulated over time as the eruption clouds dispersed. Except for an internal experimental attempt to model one of the Mount Redoubt, Alaska, eruptions (12/89), ARAC had no prior experience in modeling volcanic eruption ash hazards. For the cataclysmic eruption of 15--16 June, the complex three-dimensional atmospheric structure of the region produced dramatically divergent ash cloud patterns. The large eruptions (> 7--10 km) produced ash plume clouds with strong westward transport over the South China Sea, Southeast Asia, India and beyond. The low-level eruptions (< 7 km) and quasi-steady-state venting produced a plume which generally dispersed to the north and east throughout the support period. Modeling the sequence of eruptions presented a unique challenge. Although the initial approach proved viable, further refinement is necessary and possible. A distinct need exists to quantify eruptions consistently such that ``relative`` ash concentrations relate to specific aviation hazard categories.

Identifying glass compositions in fly ash

Directory of Open Access Journals (Sweden)

Katherine eAughenbaugh

2016-01-01

Full Text Available In this study, four Class F fly ashes were studied with a scanning electron microscope; the glassy phases were identified and their compositions quantified using point compositional analysis with k-means clustering and multispectral image analysis. The results showed that while the bulk oxide contents of the fly ashes were different, the four fly ashes had somewhat similar glassy phase compositions. Aluminosilicate glasses (AS, calcium aluminosilicate glasses (CAS, a mixed glass, and, in one case, a high iron glass were identified in the fly ashes. Quartz and iron crystalline phases were identified in each fly ash as well. The compositions of the three main glasses identified, AS, CAS, and mixed glass, were relatively similar in each ash. The amounts of each glass were varied by fly ash, with the highest calcium fly ash containing the most of calcium-containing glass. Some of the glasses were identified as intermixed in individual particles, particularly the calcium-containing glasses. Finally, the smallest particles in the fly ashes, with the most surface area available to react in alkaline solution, such as when mixed with portland cement or in alkali-activated fly ash, were not different in composition than the large particles, with each of the glasses represented. The method used in the study may be applied to a fly ash of interest for use as a cementing material in order to understand its potential for reactivity.

The Role of Biocontrol of Emerald Ash Borer in Protecting Ash Regeneration after Invasion

Science.gov (United States)

Emerald ash borer (EAB) is an invasive Asian beetle that is destroying ash in forests over much of eastern North America because of the high susceptibility of our native ash and a lack of effective natural enemies. To increase mortality of EAB larvae and eggs, the USDA (FS, ARS and APHIS) is carryin...

Characterization of fly ash, slag and glass hull for the obtaining of vitreous materials

Science.gov (United States)

Ayala Valderrama, D. M.; Gómez Cuaspud, J. A.

2017-12-01

This article presents the structural and thermal characterization of fly ash, the waste from blast furnace slag and the glass hull, generated as common residues in industry, which cannot be recycled easily or destroyed in a simple and fast way. In the particular case of fly ash, at present are being used as a lightweight aggregate in the production of cement, concrete and additive in the production of glass and glass ceramics. As far as the slag and hull, are being used as additives for the asphalt and concretes, however its use still is restricted, reason why its use in alternative ways are necessary. Initially the chemical composition of residues was established, determining that the fly ashes contains SiO2, Al2O3 and Fe2O3 oxides; 90% of the total composition, was confirmed by X-ray diffraction analysis. As minor constituents, small percentages of Mg, P, S, K, Na and Ti were found. For the slag case, the phases of Fe3O4, Ca3Mg (SiO2)4 and Ca(MgAl)(Si,Al)2O6 were identified, observing the presence of amorphous phase higher than 94% of the total phase of the system. Meanwhile, the glass hull sample showed a higher percentage of 95% amorphicity, mainly identifying a weak signal associated with silicon oxide SiO2. The thermal analyses of the samples, exhibit a decrease in mass for samples between 25-1000°C was observed, which can be attributed to different physical-chemical events that occur in the materials. The heat flow for each sample is related with the removal of the water retained by the physisorption processes around 92-110°C in all cases. With this previous characterization of the precursors, a sample was composed using 70% fly ash, 10% slag and 20% of glass hull was composed and treated at 1200°C/1.5 hours, obtaining a dense black glassy material for potential applications in field of the glass ceramics.

Characterization of residues from thermal treatment of treated wood and extraction of Cu, Cr, As and Zn

DEFF Research Database (Denmark)

Ottosen, Lisbeth M.; Pedersen, Anne Juul; Christensen, Iben Vernegren

2005-01-01

, that the charcoal contained a high concentration of Zn, probably from paint. Chemical extraction experiments in HNO were conducted with the charcoal and it was found that the order of extraction (in percentage) was Zn > Cu > As > Cr. A SEM/EDX investigation of the mixed ash from combustion showed the presence...... a matter to cope with when methods to avoid As emission are implemented: the residues with increased concentrations of Cu, Cr and As. In the present paper two different residues after thermal treatment are characterized: a mixed bottom and fly ash from combustion of CCA impregnated wood, and a charcoal...... form in a small layer on the surface of some matrix particles indicating condensation of volatile Cu species. Chemical extraction with inorganic acids showed the order of percentages mobilized as: As > Cu > Cr....

Kinetics of fly ash beneficiation by carbon burnout. Quarterly report, July 1--September 30, 1997

Energy Technology Data Exchange (ETDEWEB)

Dodoo, J.N.D.; Okoh, J.M.; Diaz, A.

1998-08-01

Oxidation studies of coal fly ash have been carried out at partial pressures in the range 1 atmosphere down to 400 torr. The studies have also been carried out at 1 atmosphere for different temperatures in the range 500 to 750 C. The equipment used was a state-of-the-art Cann Thermogravimetric analyzer having sensitive microbalance that permitted measurements to .1 {micro}g. The analyzer is part of a GC/MS/TG setup in this laboratory. The fly ash was supplied by Delmarva Power Indian River Plant, DE. The samples were dried and stored in a desiccator to ensure that they remained dry prior to combustion. The combustion process inside the TGA is continuous and the heat released can be related to the percent of carbon consumed. The setup provided easy identification of the elements in the fly ash. The elemental analysis was also augmented by use of an energy dispersive X-ray analyzer. In the X-ray analysis the carbon in the fly ash was compared with that in a dolomite (CaMg(CO{sub 3}){sub 2}) standard obtained from the US Bureau of Mines (USBOM). Preliminary data show encouraging results in the rate of reduction of the residual carbon. Both analyses show reduction of carbon after burning.

Volcanic ash impacts on critical infrastructure

Science.gov (United States)

Wilson, Thomas M.; Stewart, Carol; Sword-Daniels, Victoria; Leonard, Graham S.; Johnston, David M.; Cole, Jim W.; Wardman, Johnny; Wilson, Grant; Barnard, Scott T.

2012-01-01

Volcanic eruptions can produce a wide range of hazards. Although phenomena such as pyroclastic flows and surges, sector collapses, lahars and ballistic blocks are the most destructive and dangerous, volcanic ash is by far the most widely distributed eruption product. Although ash falls rarely endanger human life directly, threats to public health and disruption to critical infrastructure services, aviation and primary production can lead to significant societal impacts. Even relatively small eruptions can cause widespread disruption, damage and economic loss. Volcanic eruptions are, in general, infrequent and somewhat exotic occurrences, and consequently in many parts of the world, the management of critical infrastructure during volcanic crises can be improved with greater knowledge of the likely impacts. This article presents an overview of volcanic ash impacts on critical infrastructure, other than aviation and fuel supply, illustrated by findings from impact assessment reconnaissance trips carried out to a wide range of locations worldwide by our international research group and local collaborators. ‘Critical infrastructure’ includes those assets, frequently taken for granted, which are essential for the functioning of a society and economy. Electricity networks are very vulnerable to disruption from volcanic ash falls. This is particularly the case when fine ash is erupted because it has a greater tendency to adhere to line and substation insulators, where it can cause flashover (unintended electrical discharge) which can in turn cause widespread and disruptive outages. Weather conditions are a major determinant of flashover risk. Dry ash is not conductive, and heavy rain will wash ash from insulators, but light rain/mist will mobilise readily-soluble salts on the surface of the ash grains and lower the ash layer’s resistivity. Wet ash is also heavier than dry ash, increasing the risk of line breakage or tower/pole collapse. Particular issues for water

Decoupled numerical simulation of a solid fuel fired retort boiler

International Nuclear Information System (INIS)

Ryfa, Arkadiusz; Buczynski, Rafal; Chabinski, Michal; Szlek, Andrzej; Bialecki, Ryszard A.

2014-01-01

The paper deals with numerical simulation of the retort boiler fired with solid fuel. Such constructions are very popular for heating systems and their development is mostly based on the designer experience. The simulations have been done in ANSYS/Fluent package and involved two numerical models. The former deals with a fixed-bed combustion of the solid fuel and free-board gas combustion. Solid fuel combustion is based on the coal kinetic parameters. This model encompasses chemical reactions, radiative heat transfer and turbulence. Coal properties have been defined with user defined functions. The latter model describes flow of water inside a water jacked that surrounds the combustion chamber and flue gas ducts. The novelty of the proposed approach is separating of the combustion simulation from the water flow. Such approach allows for reducing the number of degrees of freedom and thus lowering the necessary numerical effort. Decoupling combustion from water flow requires defining interface boundary condition. As this boundary condition is unknown it is adjusted iteratively. The results of the numerical simulation have been successfully validated against measurement data. - Highlights: • New decoupled modelling of small scale boiler is proposed. • Fixed-bed combustion model based on kinetic parameters is introduced. • Decoupling reduced the complexity of the model and computational time. • Simple and computationally inexpensive coupling algorithm is proposed. • Model is successfully validated against measurements

Transcriptomic signatures of ash (Fraxinus spp. phloem.

Directory of Open Access Journals (Sweden)

Xiaodong Bai

2011-01-01

Full Text Available Ash (Fraxinus spp. is a dominant tree species throughout urban and forested landscapes of North America (NA. The rapid invasion of NA by emerald ash borer (Agrilus planipennis, a wood-boring beetle endemic to Eastern Asia, has resulted in the death of millions of ash trees and threatens billions more. Larvae feed primarily on phloem tissue, which girdles and kills the tree. While NA ash species including black (F. nigra, green (F. pennsylvannica and white (F. americana are highly susceptible, the Asian species Manchurian ash (F. mandshurica is resistant to A. planipennis perhaps due to their co-evolutionary history. Little is known about the molecular genetics of ash. Hence, we undertook a functional genomics approach to identify the repertoire of genes expressed in ash phloem.Using 454 pyrosequencing we obtained 58,673 high quality ash sequences from pooled phloem samples of green, white, black, blue and Manchurian ash. Intriguingly, 45% of the deduced proteins were not significantly similar to any sequences in the GenBank non-redundant database. KEGG analysis of the ash sequences revealed a high occurrence of defense related genes. Expression analysis of early regulators potentially involved in plant defense (i.e. transcription factors, calcium dependent protein kinases and a lipoxygenase 3 revealed higher mRNA levels in resistant ash compared to susceptible ash species. Lastly, we predicted a total of 1,272 single nucleotide polymorphisms and 980 microsatellite loci, among which seven microsatellite loci showed polymorphism between different ash species.The current transcriptomic data provide an invaluable resource for understanding the genetic make-up of ash phloem, the target tissue of A. planipennis. These data along with future functional studies could lead to the identification/characterization of defense genes involved in resistance of ash to A. planipennis, and in future ash breeding programs for marker development.

Spectral analysis of white ash response to emerald ash borer infestations

Science.gov (United States)

Calandra, Laura

The emerald ash borer (EAB) (Agrilus planipennis Fairmaire) is an invasive insect that has killed over 50 million ash trees in the US. The goal of this research was to establish a method to identify ash trees infested with EAB using remote sensing techniques at the leaf-level and tree crown level. First, a field-based study at the leaf-level used the range of spectral bands from the WorldView-2 sensor to determine if there was a significant difference between EAB-infested white ash (Fraxinus americana) and healthy leaves. Binary logistic regression models were developed using individual and combinations of wavelengths; the most successful model included 545 and 950 nm bands. The second half of this research employed imagery to identify healthy and EAB-infested trees, comparing pixel- and object-based methods by applying an unsupervised classification approach and a tree crown delineation algorithm, respectively. The pixel-based models attained the highest overall accuracies.

Hippocampus lipid peroxidation induced by residual oil fly ash intranasal instillation versus habituation to the open field.

Science.gov (United States)

Zanchi, Ana Claudia; Saiki, Mitiko; Saldiva, Paulo Hilário Nascimento; Barros, Helena Maria Tannhauser; Rhoden, Claudia Ramos

2010-01-01

Epidemiological studies have demonstrated the adverse effects of particulate matter (PM) inhalation on the respiratory and cardiovascular systems. It has been reported that air pollution may affect the central nervous system and decrease cognitive function. In rats, residual oil fly ash (ROFA) instillation causes decreased motor activity and increased lipid peroxidation in the striatum and the cerebellum. Our objective was to determine whether chronic instillation of particles induces changes in learning and memory in rats and whether oxidants in the hippocampus may contribute to these adverse effects. Forty-five-day-old male Wistar rats were exposed to ROFA by intranasal instillation and were treated with N-acetylcysteine (NAC) at 150 mg/kg i.p. for 30 days. Control groups were exposed to ROFA, NAC, or neither. On days 1, 8, and 30 of the protocol, rats were submitted to the open field test to evaluate habituation. After the last open field session, the rats were killed by decapitation. The hippocampus was used to determine lipid peroxidation (LP) by the thiobarbituric acid-reactive substances test. ROFA instillation induced an increase in LP in the hippocampus compared to all treatment groups (p = .012). NAC treatment blocked these changes. All of the treatment groups presented a decrease in the frequency of peripheral walking (p = .001), rearing (p = .001), and exploration (p = .001) over time. Our study demonstrates that exposure to particles for 30 days and/or NAC treatment do not modify habituation to an open field, a simple form of learning and memory in rats, and that oxidative damage induced by ROFA does not modulate these processes.

Application of Coal Ash to Postmine Land for Prevention of Soil Erosion in Coal Mine in Indonesia: Utilization of Fly Ash and Bottom Ash

Directory of Open Access Journals (Sweden)

Shinji Matsumoto

2016-01-01

Full Text Available The increase in the number of coal-fired power plants with the increase in coal production and its consumption has caused the problem of the treatment of a large amount of coal ash in Indonesia. In the past studies, coal ash was applied to postmine land with the aim of improving soil conditions for plant growth; however, heavy rain in the tropical climate may cause soil erosion with the change in soil conditions. This study presents the effects of application of coal ash to postmine land on soil erosion by performing the artificial rainfall test as well as physical testing. The results indicate that the risk of soil erosion can be reduced significantly by applying the coal ash which consists of more than 85% of sand to topsoil in the postmine land at the mixing ratio of over 30%. Additionally, they reveal that not only fine fractions but also microporous structures in coal ash enhance water retention capacity by retaining water in the structure, leading to the prevention of soil erosion. Thus, the risk of soil erosion can be reduced by applying coal ash to topsoil in consideration of soil composition and microporous structure of coal ash.

Impact strength and abrasion resistance of high strength concrete with rice husk ash and rubber tires

Directory of Open Access Journals (Sweden)

M. B. Barbosa

Full Text Available The paper discusses the application of High Strength Concrete (HSC technology for concrete production with the incorporation of Rice Husk Ash (RHA residues by replacing a bulk of the material caking and rubber tires with partial aggregate volume, assessing their influence on the mechanical properties and durability. For concrete with RHA and rubber, it was possible to reduce the brittleness by increasing the energy absorbing capacity. With respect to abrasion, the RHA and rubber concretes showed lower mass loss than the concrete without residues, indicating that this material is attractive to be used in paving. It is thus hoped that these residues may represent a technological and ecological alternative for the production of concrete in construction works.

Energy from briquettes produced from remains of urban solid residues and wood of Eucalyptus grandis; Energia de briquetes produzidos com rejeitos de residuos solidos urbanos e madeira de Eucalyptus grandis

Energy Technology Data Exchange (ETDEWEB)

Goncalves, Jose E.; Leao, Alcides L. [Universidade Estadual Paulista Julio de Mesquita Filho (UNESP), Botucatu, SP (Brazil). Dept. de Ciencias Ambientais], emails: evaristo@fca.unesp.br, alcidesleao@fca.unesp.br; Sartori, Maria M.P. [Universidade Estadual Paulista Julio de Mesquita Filho (UNESP), Bauru, SP (Brazil). Dept. de Engenharia de Producao], email: msartori@btu.flash.tv.br

2009-07-01

The incentive for consumption and production in large quantity in modern society generates enormous amounts of urban solid residues in the form of municipal solid waste (MSW). With the intention of reducing these residues of the municipal waste tips and to generate energy, briquettes with mixtures of MSW and residues of Eucalyptus grandis were produced. The briquettes were manufactured with 0, 5, 10, 15, 20 and 25% of MSW in the mixture with wood waste and 12% of moisture content. The analyzed parameters used to choose the best treatments were combustion analysis versus ash content, mechanical strength and energy content. The briquettes up to 10% of MSW showed low resistance, and above 15% showed large increase in ash content. Therefore, the treatment that fulfilled the requirements for combustion versus ash content and mechanical resistance was of at least 15% of MSW, since the source of the ash is unidentified. Considering the net energy content, the best treatment was 25% of MSW, with 17,175 kJ kg{sup -1}. Nevertheless, it is strongly advised that further studies related to gas emissions are necessary. (author)

Possibilities of utilizing power plant fly ashes

Directory of Open Access Journals (Sweden)

Mezencevová Andrea

2003-09-01