WorldWideScience

Sample records for resuspension final comparison

  1. International Standard Problem 40 - Aerosol Deposition and Resuspension. Final Comparison Report

    International Nuclear Information System (INIS)

    De Los Reyes, Alfredo Castelo; Areia Capitao, Joaquim; De Santi, Giovanni

    1999-02-01

    -October 1997 and the deadline for submission of the results of this second phase was the end of January 1998. A first draft of this comparison report was produced in March 1998, followed by a workshop in Ispra in mid-March. Two errors in the supplied data had been detected and were communicated to the participants in this workshop, one concerning the steam flow rate in the deposition phase of the exercise and the other the size distribution of the resuspended aerosols in the resuspension phase. The decision whether or not to re-do their calculations was left to the each ISP participant and the deadline for the submission of new results, with these or other modifications relative to the previous ones, was the end of May 1998. These new calculations, having been performed in open conditions, are presented separately in this report. The final draft of the comparison report was distribute in June 1998, followed by a final workshop in Ispra the same month. This report is divided into six main sections, one concerning the experimental set-up and results, two each for the deposition and resuspension phases of the International Standard Problem (blind and open calculations), and one on general conclusions and recommendations. According to the opinion of the ISP participants, the results in the two sections on the deposition and resuspension exercises are listed by computer code and, for each code, by organisation. The calculations submitted by the Joint Research Centre are included together with the others. Although the JRC staff who performed the calculations did not have access to the experimental results before submitting their results, their knowledge of the facility puts their calculations in a separate class

  2. Wet and dry deposition and resuspension of AFCT/TFCT fuel processing radionuclides. Final report

    International Nuclear Information System (INIS)

    Slinn, W.G.N.; Katen, P.C.; Wolf, M.A.; Loveland, W.D.; Radke, L.F.; Miller, E.L.; Ghannam, L.J.; Reynolds, B.W.; Vickers, D.

    1979-09-01

    After short summary and introductory chapters, Chapter IV contains a critical analysis of available parameterizations for resuspension and for wet and dry removal processes and recommends interim parameterizations for use in radiation dose calculations. Chapter V describes methods and experimental results from field studies of in-cloud vs below-cloud scavenging, precipitation efficiency, and modifications of aerosols by clouds. In Chapter VI are contained descriptions of methods and results from four different approaches to the problem of measuring the dry deposition velocities of submicron aerosol particles depositing on vegetation. Chapter VII describes experimental results from a study of resuspension and weathering of tracer aerosol particles deposited on soil, grass and gravel; typical resuspension rates were found to be of the order of 10 -8 s -1 and it is recommended that the concept of weathering be reassessed. In Chapter VIII, National Weather Service data are used to obtain Lagrangian statistics for use in a regional-scale study of wet and dry removal. Chapter IX develops new concepts in reservoir models for application at regional to global scales. In the final chapter are some comments about the results found in this study and recommendations for future research

  3. Review of resuspension models

    International Nuclear Information System (INIS)

    Healy, J.W.

    1976-01-01

    Resuspension of particles is classified, according to the prominent path of exposure and the type of consideration involved in estimating concentrations, as general resuspension, local resuspension, and transfer resuspension. General resuspension can be driven by winds or mechanical disturbances while local resuspension and transfer resuspension are primarily caused by mechanical disturbances. Modeling techniques consist of the resuspension factor, the resuspension rate and mass-loading. For general resuspension the resuspension rate is preferred while the resuspension factor or mass-loading approach can be used for local resuspension. Data for estimation of transfer resuspension are not really adequate to even make a first approximation as to its importance. Resuspension of contaminants on the ground leading to inhalation is generally assumed to be an important pathway of exposure to people. Methods of calculation for prediction of this pathway (models) are used widely in Environmental Impact Statements, risk assessments, and derivation of standards

  4. Investigations into the resuspension of plutonium in the biosphere. Final report

    International Nuclear Information System (INIS)

    Baechmann, K.

    1991-01-01

    In order to compare the resuspension behaviour of Pu with that of other elements, inactive elements were included into the investigations. The following measurements were made: 1. Determination of Pu surface contamination of the ground and of surface concentration of the inactive elements; 2. vertical distributions of the elements in the atmosphere; 3. particle size distributions of the elements; 4. element correlations; 5. determination of resuspension parameters. The measurements were made over a longer period of time in order to detect changes of Pu and of the inactive elements in terms of time and space. With the same resuspension behaviour of Pu and inactive elements, the latter, because of their quick determinability, could serve as model elements to predict Pu behaviour. (orig.) [de

  5. Resuspension of carbon dust collected in Tore Supra and exposed to turbulent airflow: Controlled experiments and comparison with model

    Energy Technology Data Exchange (ETDEWEB)

    Peillon, S., E-mail: samuel.peillon@irsn.fr [Institut de Radioprotection et de Sûreté Nucléaire (IRSN), PSN-RES/SCA/LPMA, Saclay, Gif-sur-Yvette 91192 (France); Roynette, A. [Institut de Radioprotection et de Sûreté Nucléaire (IRSN), PSN-RES/SCA/LPMA, Saclay, Gif-sur-Yvette 91192 (France); Grisolia, C. [CEA, IRFM, F-13108 Saint-Paul-lez-Durance (France); Gensdarmes, F. [Institut de Radioprotection et de Sûreté Nucléaire (IRSN), PSN-RES/SCA/LPMA, Saclay, Gif-sur-Yvette 91192 (France)

    2014-11-15

    Highlights: • Mobilization of dust is a key issue for the safety assessment of fusion reactors. • Carbon dust has been collected on the plasma facing components of Tore Supra. • Samples exhibit bimodal particle size distributions. • Samples have been exposed to turbulent airflows for dust resuspension studies. • A comparison with the so-called Rock’n roll resuspension model is proposed. - Abstract: This work presents the results of experiments conducted with carbon microparticles collected in the tokamak Tore Supra in order to characterize their resuspension behaviour from a stainless-steel substrate when exposed to turbulent airflow. Experiments were conducted in a wind tunnel with controlled velocity profiles and monitored environmental conditions. A consequent amount of dust has been collected in the vessel of the tokamak and a bimodal particle size distribution of samples is first demonstrated. Comparison with resuspension of alumina powders with equivalent particle size distributions under turbulent airflow is also discussed. Results for both carbon and alumina microparticles are then compared to a theoretical resuspension model. Data reveal that exposing multilayer deposits with bimodal particle size distributions to low-speed flows (i.e. 3–10 m/s) induces a significant reduction of the mobilized fractions compared to what was predicted by the model. In addition, results helped to highlight some limitations in the model to physically describe changes in the adhesive strength that can occur with a polydisperse deposit.

  6. Particle resuspension due to human walking

    International Nuclear Information System (INIS)

    Mana, Zakaria

    2014-01-01

    et al. (1971)). Moreover, this technique, taking into account the surface roughness, shows that adhesion forces decrease while particle diameter increase. Finally, the analysis of AFM measurements gives a correlation linking the distribution of adhesion forces to the particle diameter, replacing the one given by Biasi et al. (2001) originally used in the Rock'n'Roll model and thereby adapt the model to particles and flooring studied in our case. Coupling, performed in ANSYS CFX software, between the calculations of friction velocity and model of particle resuspension, gives theoretical resuspension rate during shoe motion. This coupling was initially validated by comparison to the experience for the simple case of a rotating plate in a controlled volume. Secondly, experiments at the scale of a ventilated room of 30 m 3 were performed by walking on an epoxy coating initially seeded by calibrated particle size (1.1 μm and 3.3 μm). These experiments highlight the parameters influencing the suspension of particles, such as step frequency and particle size. (author)

  7. Transuranic resuspension

    International Nuclear Information System (INIS)

    Sehmel, G.A.

    1984-04-01

    Characteristics of aged resuspension sources are more uncertain than those of new resuspension sources, which can be investigated using inert-particle controlled-tracer sources. Even though airborne concentrations are low, one aged uniform-area source which can be used for resuspension studies is the accumulated radionuclide fallout in the soil from stratospheric and tropospheric fallout debris. Airborne radionuclide concentrations from this source were investigated at convenient locations on the Hanford site. The objective is to summarize plutonium and americium resuspension research conducted by the Pacific Northwest Laboratory from 1977 to 1983. Airborne plutonium was determined at five sites in the Hanford area, and both plutonium and americium were determined at two Hanford sites. Airborne plutonium and americium were examined as a function of aerodynamic particle diameter, sampling height, wind speed increments, and wind direction increments. The following results are discussed: airborne radionuclide concentrations, μCi/cm 3 of sampled air; radionuclide activity densities, μCi/g of airborne solids; airborne plutonium fluxes, μCi/(m 2 day); 241 Am/ 239+240 Pu) activity ratios, (μCi 241 Am)/(μCi 239+240 Pu); and airborne solid concentrations, μg/m 3 of sampled air. In addition, a relationship based on field data for aged plutonium sources at Bikini Atoll, the Hanford site, and Rocky Flats was developed to estimate the maximum expected plutonium activity density on airborne solids compared to activity densities for bulk surface-soil samples. As a result, it is possible to more accurately predict resuspension factor ranges as a function of the resuspension source activity densities. 31 references, 18 figures, 5 tables

  8. Resuspension of particulate material from grass. Experimental programme 1979 - 1980

    International Nuclear Information System (INIS)

    Garland, J.A.

    1982-02-01

    Further wind tunnel experiments on resuspension are presented. In one, the effect of natural weathering was investigated. The grass was exposed to natural wind and rain between measurement periods. Results showed that natural weathering reduced the concentration of the tungstic oxide (WO 3 ) tracer found in the air in subsequent resuspension measurements at least as rapidly as exposure to high winds alone. Another experiment showed that 60% of the WO 3 resuspended from a small contaminated area deposited again within 4 m. Finally, resuspension from grass of 2 μm and 5 μm iron oxide particles and of ferric chloride applied in solution are reported and compared with tungstic oxide and silt. After the first few hours, the resuspension rate increased in the order: submicron WO 3 powder, silt, ferric chloride, 2 μm particles, 5 μm particles, with a ratio of about a hundred between the highest and lowest. The problem of extrapolating from small-scale experiments to contamination on a larger scale is discussed. Resuspension factors for grassland in N W Europe appear to be comparable with those observed in more arid conditions in the USA, but resuspension formulae previously proposed by American workers are probably conservative by about an order of magnitude if applied in Europe. (author)

  9. Particle resuspension from a multi-layer deposit by turbulent flow

    International Nuclear Information System (INIS)

    Fromentin, A.

    1989-09-01

    The aim of this work was to contribute to the understanding and quantification of particle resuspension from a bed exposed to a turbulent flow. The PARESS experiment has been set up and conducted. Multi-layer deposits of particles were created by allowing aerosols to settle on steel plates under conditions typical of a nuclear reactor containment following a severe accident. These were then exposed to a controlled turbulent airflow (U ∞ =5-25 m/s) in a wind tunnel and the evolution of the resuspension flux as a function of time was measured. The resuspension flux F r decreased with exposure time to the airflow t, according to a power law F r = a.t -b [kg/m 2 .s]. The parameters a and b depend on the flow velocity and the nature of the deposit. A new semi-empirical model, based on the comparison between the distributions of adhesive forces holding the particles on the deposit and aerodynamic forces tending to remove them, has been developed to simulate the stochastic nature of particle resuspension. This model is able to predict the experimentally observed decrease of the resuspension flux as a function of time and its dependence on flow velocity. Based on the results of the PARESS experiment, an empirical global relationship, which ignores the fine effects due to the nature of the different deposits, has been proposed. It appears that the resuspension flux is approximately proportinal to the cube of the flow velocity, and that a pseudo threshold velocity exists below which virtually no resuspension occurs. (author) 57 figs., 1 tab., 79 refs

  10. Plutonium and tracer particle resuspension: an overview of selected Battelle-Northwest experiments

    International Nuclear Information System (INIS)

    Sehmel, G.A.

    1977-01-01

    Plutonium resuspension at Rocky Flats was determined in July 1973, by measuring airborne plutonium as a function of sampling height and of wind speed. The maximum airborne plutonium-239 concentration was 3700 aCi/m 3 . The maximum plutonium-239 activity per gram of collected airborne soil was 50 pCi/g. Airborne plutonium concentrations were shown to increase as the sixth power of wind speed, but the data were very imprecise. In measurement of fallout resuspension caused by burning vegetation, the 137 Cs concentration in a forest fire smoke plume was 22 times the concentration in ambient air. Resuspension rates for a man walking across a tracer area on an asphalt surface ranged from 1 x 10 -5 to 7 x 10 -4 fraction of tracer resuspended/pass. For vehicular traffic driven on a tracer lane, resuspension rates from the asphalt surface ranged from 10 -4 to 10 -2 fraction resuspended/pass. When the vehicle was driven on the lane adjacent to the tracer lane, resuspension rates were smaller, ranging from 10 -5 to 10 -3 fraction resuspended/pass. Resuspension rates decreased when the tracer had been on the ground for several days. In comparison to the asphalt surface, vehicle-caused tracer resuspension rates from a cheat grass area were lower, ranging from 10 -5 to 10 -4 fraction resuspended/pass. Wind caused tracer resuspension rates were on the order of 10 -11 fraction resuspended/sec for nonrespirable particles. Resuspension rates for respirable particles increased as the 4.8th power of wind speed, ranging from 10 -11 to 10 -7 fraction resuspended/sec. In another study, airborne respirable soil concentrations measured as a function of wind speed increased as the 0.6 to 3.2 power of wind speed

  11. Resuspension and transport of suspended solids in Eurajoensalmi Bay. Final report of monitoring activities in 2009-2011

    International Nuclear Information System (INIS)

    Mykkanen, J.; Kiirikki, M.; Lindfors, A.

    2012-11-01

    The goal of monitoring activities carried out in Eurajoensalmi Bay was to indentify factors affecting dispersal of river waters and suspended solid matter in the estuary area. In addition to suspended solids load and dispersal of river water, also release of sedimented particles from the sea bed in resuspension was studied. River water quality and discharge as well as resuspension in Eurajoensalmi estuary area were monitored with Luode automatic monitoring stations equipped with water quality, water level, wave height and weather sensors. Dynamics of Eurajoensalmi estuary area was studied by installing profiling current meters (ADCP) and water quality sensors to the sea floor at the mouth of Eurajoensalmi. Spatial variation of surface water quality was monitored with a flow-through method from a moving vessel and manual profiling several times during the monitoring period. Collected data was processed and used in determining suspended solids balance of Eurajoensalmi Bay. The balance was determined by creating a regression model for water exchange and sediment flux over the cross section at the mouth of Eurajoensalmi. Regression model was created also to determine resuspension in Eurajoensalmi area. Sediment flux and resuspension were modeled using long term wind data from Kylmaepihlaja meteorological station as a variable to determine overall sediment balance of Eurajoensalmi

  12. The Modelling of Particle Resuspension in a Turbulent Boundary Layer

    International Nuclear Information System (INIS)

    Zhang, Fan

    2011-01-01

    lift and drag forces in turbulent boundary layers, the lift and drag we have con sidered and the impact of these data on predictions made by the non-Gaussian R'n'R model are compared with those based on O'Neill formula. The results indicate that, in terms of the long-term resuspension fraction, the difference is minor. It is concluded that as the particle size decreases the L and B method will lead to less-and-less long-term resuspension. Finally the ultimate model that has been developed in this work is a hybrid version of the R'n'R model adapted for application to multilayer deposits based on the Friess and Yadigaroglu multilayer approach. The deposit is modelled in several overlying layers where the coverage effect (masking) of the deposit layers has been studied; in the first instance a monodisperse deposit with a coverage ratio factor was modelled where this was subsequently replaced by the more general case of a polydisperse deposit with a particle size distribution. The results indicate that, in general, as the number of modelled layers increases the resuspension fraction of the whole deposit after a certain time decreases significantly. In other words, it takes a much longer time to re-suspend a thicker deposit. Taking account of the particle size distribution slightly increases the short-term resuspension. However, this change decreases the long-term resuspension significantly. The model results have been compared with data from the STORM SR11 test (ISP-40) and the BISE experiments. In general, both comparisons indicate that with smaller spread of the adhesive force distribution the new multilayer model agrees very well with the experimental data. It can be inferred that multilayer deposits lead to much narrower distributions of adhesive force

  13. Overview of resuspension model: application to low level waste management

    International Nuclear Information System (INIS)

    Healy, J.W.

    1980-01-01

    Resuspension is one of the potential pathways to man for radioactive or chemical contaminants that are in the biosphere. In waste management, spills or other surface contamination can serve as a source for resuspension during the operational phase. After the low-level waste disposal area is closed, radioactive materials can be brought to the surface by animals or insects or, in the long term, the surface can be removed by erosion. Any of these methods expose the material to resuspension in the atmosphere. Intrusion into the waste mass can produce resuspension of potential hazard to the intruder. Removal of items from the waste mass by scavengers or archeologists can result in potential resuspension exposure to others handling or working with the object. The ways in which resuspension can occur are wind resuspension, mechanical resuspension and local resuspension. While methods of predicting exposure are not accurate, they include the use of the resuspension factor, the resuspension rate and mass loading of the air

  14. Deposition and Resuspension of Particles

    DEFF Research Database (Denmark)

    Lengweiler, P.; Nielsen, Peter V.; Moser, A.

    A new experimental set-up to investigate the physical process of dust deposition and resuspension on and from surfaces is introduced. Dust deposition can reduce the airBorne dust concentration considerably. As a basis for developing methods to eliminate dust related problems in rooms......, there is a need for better understanding of the mechanism of dust deposition and resuspension....

  15. Resuspension and deposition of radionuclides under various conditions

    International Nuclear Information System (INIS)

    Garger, E.; Gordeev, S.; Hollaender, W.; Kashparov, V.; Kashpur, V.; Martinez-Serrano, J.; Mironov, V.; Peres, J.; Tschiersch, J.; Vintersved, I.; Watterson, J.

    1996-01-01

    The resuspension of 137 Cs and 239+240 Pu has been assessed at sites within and outside the 30 km exclusion zone around Chernobyl. Measurements were made during periods of wind-derived resuspension and during simulated and real agricultural activity. From these data, resuspension rates (fraction of deposit removed in unit time) or emission rates (fraction of deposit removed in unit time or unit area) have been calculated. Resuspension rates of 137 Cs have declined by at least an order of magnitude 7 years after the accident and were found to be of the order of 10 -10 s -1 . During agricultural activity, the resuspension rate may exceed background levels by four orders of magnitude

  16. The influence of human physical activity and contaminated clothing type on particle resuspension

    International Nuclear Information System (INIS)

    McDonagh, A.; Byrne, M.A.

    2014-01-01

    A study was conducted to experimentally quantify the influence of three variables on the level of resuspension of hazardous aerosol particles from clothing. Variables investigated include physical activity level (two levels, low and high), surface type (four different clothing material types), and time i.e. the rate at which particles resuspend. A mixture of three monodisperse tracer-labelled powders, with median diameters of 3, 5, and 10 microns, was used to “contaminate” the samples, and the resuspended particles were analysed in real-time using an Aerodynamic Particle Sizer (APS), and also by Neutron Activation Analysis (NAA). The overall finding was that physical activity resulted in up to 67% of the contamination deposited on clothing being resuspended back into the air. A detailed examination of the influence of physical activity level on resuspension, from NAA, revealed that the average resuspended fraction (RF) of particles at low physical activity was 28 ± 8%, and at high physical activity was 30 ± 7%, while the APS data revealed a tenfold increase in the cumulative mass of airborne particles during high physical activity in comparison to that during low physical activity. The results also suggest that it is not the contaminated clothing's fibre type which influences particle resuspension, but the material's weave pattern (and hence the material's surface texture). Investigation of the time variation in resuspended particle concentrations indicated that the data were separable into two distinct regimes: the first (occurring within the first 1.5 min) having a high, positive rate of change of airborne particle concentration relative to the second regime. The second regime revealed a slower rate of change of particle concentration and remained relatively unchanged for the remainder of each resuspension event. -- Highlights: • Experimental investigation of the resuspension of hazardous particles from clothing. • Influence of human physical activity

  17. Turbulent resuspension of small nondeformable particles

    International Nuclear Information System (INIS)

    Lazaridis, M.; Drossinos, Y.

    1998-01-01

    An energy-balance resuspension model is modified and applied to the resuspension of a monolayer of nondeformable spherical particles. The particle-surface adhesive force is calculated from a microscopic model based on the Lennard-Jones intermolecular potential. Pairwise additivity of intermolecular interactions is assumed and elastic flattening of the particles is neglected. From the resulting particle-surface interaction potential the natural frequency of vibration of a particle on a surface and the depth of the potential well are calculated. The particle resuspension rate is calculated using the results of a previously developed energy-balance model, where the influence of fluid flow on the bound particle motion is recognized. The effect of surface roughness is included by introducing an effective particle radius that results in log-normally distributed adhesive forces. The predictions of the model are compared with experimental results for the resuspension of Al 2 O 3 particles from stainless steel surfaces. Particle resuspension due to turbulent fluid flow is important in the interaction of the atmosphere with various surfaces and in numerous industrial processes. For example, in the nuclear industry, fission-product aerosols released during a postulated severe accident in a Light Water Reactor may deposit and resuspend repeatedly in the vessel circuit and containment

  18. Sediment Resuspension Data

    Data.gov (United States)

    U.S. Environmental Protection Agency — The full report on sediment resuspension in drinking water storage tanks and a link to an animation of results. This dataset is associated with the following...

  19. Resuspension of particulate matter from grass and soil

    International Nuclear Information System (INIS)

    Garland, J.A.

    1979-05-01

    Measurements of resuspension of particulate matter from grassland and bare soil in Britain at controlled wind speeds are described in this report. The measurements were performed in an outdoor wind tunnel. Resuspension factors for a sub-micron powder deposited from the air on to 10m 2 of grass and soil and for a suspension of silt, sprayed on to a similar grass area, were similar. The resuspension factor declined as the reciprocal of time of wind exposure and increased as the square or cube of wind speed. An appreciable fraction of the resuspended tracer was in the respirable size range. A large fraction of the total material suspended from a small contaminated area deposited again within three metres. The strong dependence of deposition rates on particle size and the rapid deposition close to the source questions the extrapolation of small scale resuspension measurements to practical situations, suggesting that analysis of the concentrations of widely distributed tracers may usefully supplement resuspension measurements. Atmospheric concentrations of trace elements and the distribution of weapons fallout were used to deduce an upper limit for the resuspension factor for a fifteen year old deposit of 7 x 10 -11 m -1 . The fraction of deposited fallout resuspended during such a period cannot much exceed 10 per cent. (author)

  20. Dispersion, deposition and resuspension of atmospheric contaminants

    International Nuclear Information System (INIS)

    Anon.

    1985-01-01

    The following topics are discussed: dry deposition, oil shale fugitive air emissions, particle resuspension and translocation, theoretical studies and applications, and processing of emissions by clouds and precipitation. The concentration of contaminant species in air is governed by the rate of input from sources, the rate of dilution or dispersion as a result of air turbulence, and the rate of removal to the surface by wet and dry deposition processes. Once on the surface, contaminants also may be resuspended, depending on meteorological and surface conditions. An understanding of these processes is necessary for accurate prediction of exposures of hazardous or harmful contaminants to humans, animals, and crops. In the field, plume dispersion and plume depletion by dry deposition were studied by the use of tracers. Dry deposition was investigated for particles of both respiration and inhalation interest. Complementary dry deposition studies of particles to rock canopies were conducted under controlled conditions in a wind tunnel. Because of increasing concern about hazardous, organic gases in the atmosphere some limited investigations of the dry deposition of nitrobenzene to a lichen mat were conducted in a stirred chamber. Resuspension was also studied using tracers and contaminated surfaces and in the wind tunnel. The objective of the resuspension studies was to develop and verify models for predicting the airborne concentrations of contaminants over areas with surface contamination, develop resuspension rate predictors for downwind transport, and develop predictors for resuspension input to the food chain. These models will be of particular relevance to the evaluation of deposition and resuspension of both radionuclides and chemical contaminants

  1. Study of the aeraulic re-suspension applied to the dust issue in the future ITER tokamak

    International Nuclear Information System (INIS)

    Rondeau, Anthony

    2015-01-01

    In ITER, a loss of vacuum accident is likely to re-suspend particles produced and deposited on the torus walls. The thesis purpose is to provide reliable experimental data to develop and validate a re-suspension model, taking into account the low pressure and predicting the amount of particles mobilized during such event. Experiments were carried out as a function of key parameters - particle diameter, friction velocity and density of the atmosphere - entering in the re-suspension mechanism. The size distribution of tungsten particles produced in tokamaks shows diameters from 0.1 to 10 μm. The experimental data of tungsten particle monolayer deposits re-suspension are in good agreement with the Rock'n Roll model when the particles are only mobilised by the fluid. However, a mobilisation of fine particles by clustering, no taken into account in re-suspension models, was highlighted. My experiments have also revealed the importance of the multilayers deposit structure (porosity and thickness) in the re-suspension mechanism with, here again, a mobilisation by particle clustering. The effect of low pressure in the re-suspension mechanism was studied between 10 and 1,000 mbar and shows a friction reduction in the airflow forces at low pressure. Finally, measurements of the MES phenomenon kinetics highlighted three distinct regions with a short-term effect, a long-term effect and a transition region which must be taken into account in a MES calculation. (author)

  2. The Modelling of Particle Resuspension in a Turbulent Boundary Layer

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Fan

    2011-10-20

    second is the value of the ratio of the root-mean-square (rms) drag force to its mean value which in the modified model is nearly twice than that in the original. The third feature introduces changes in the resuspension because the distribution of aerodynamic drag forces in the modified model is distinctly non-Gaussian behaving more like a Rayleigh distribution. This means that the distribution of the drag force decays much more slowly in the wings of the distribution than the equivalent Gaussian so that for very large values of the adhesive force / rms drag force {approx}8, the resuspension rate constant is a factor of 30 larger than that for an equivalent Gaussian model. Thus although the fraction of particles resuspended is very small in these instances, the differences between the modified and original models can be very large. This is particularly important when we consider resuspension from multilayer deposits. When we consider these influences in the context of a broad range of adhesive forces due to surface roughness, we find that in general, the modified model gives around 10% more for the fraction of particle resuspension fraction than the original R'n'R model, however the difference could become significant when the friction velocity is small. As for the short-term resuspension rate, the difference between the modified and original model becomes significant when this is dominated by the typical forcing frequency. The sensitivity to the adhesive-force spread factor has also been studied and the results indicate that the modified model removes particles much more easily than the original model in conditions of small friction velocity and a smoother surface. Finally in this phase of the work, the correlation between the distribution of the fluctuating force and its derivative has been checked for both LES and DNS statistics. The results demonstrate that this correlation has a very slight effect on particle resuspension compared with the result from the

  3. Transuranic and tracer simulant resuspension

    International Nuclear Information System (INIS)

    Sehmel, G.A.

    1977-07-01

    Plutonium resuspension results are summarized for experiments conducted at Rocky Flats, onsite on the Hanford reservation, and for winds blowing from offsite onto the Hanford reservation near the Prosser barricade boundary. In each case, plutonium resuspension was shown by increased airborne plutonium concentrations as a function of either wind speed or as compared to fallout levels. All measured airborne concentrations were below maximum permissible concentrations (MPC). Both plutonium and cesium concentrations on airborne soil were normalized by the quantity of airborne soil sampled. Airborne radionuclide concentrations in μCi/g were related to published values for radionuclide concentrations on surface soils. For this ratio of radionuclide concentration per gram on airborne soil divided by that for ground surface soil, there are eight orders of magnitude uncertainty from 10 -4 to 10 4 . Horizontal plutonium fluxes on airborne nonrespirable soils at all three sites were bracketed within the same three to four orders of magnitude from 10 -7 to 10 -3 μCi/(m 2 day) for plutonium-239 and 10 -8 to 10 -5 μCi/(m 2 day) for plutonium-238. These are the entire experimental base for nonrespirable airborne plutonium transport. Airborne respirable plutonium-239 concentrations increased with wind speed for a southeast wind direction coming from offsite near the Hanford reservation Prosser barricade. Airborne plutonium fluxes on nonrespirable particles had isotopic ratios, 240 Pu/ 239+240 Pu, similar to weapons grade plutonium rather than fallout plutonium. Resuspension rates were summarized for controlled inert particle tracer simulant experiments. Wind resuspension rates for tracers increased with wind speed to about the fifth power

  4. Quantifying road dust resuspension in urban environment by Multilinear Engine: A comparison with PMF2

    Science.gov (United States)

    Amato, F.; Pandolfi, M.; Escrig, A.; Querol, X.; Alastuey, A.; Pey, J.; Perez, N.; Hopke, P. K.

    Atmospheric PM pollution from traffic comprises not only direct emissions but also non-exhaust emissions because resuspension of road dust that can produce high human exposure to heavy metals, metalloids, and mineral matter. A key task for establishing mitigation or preventive measures is estimating the contribution of road dust resuspension to the atmospheric PM mixture. Several source apportionment studies, applying receptor modeling at urban background sites, have shown the difficulty in identifying a road dust source separately from other mineral sources or vehicular exhausts. The Multilinear Engine (ME-2) is a computer program that can solve the Positive Matrix Factorization (PMF) problem. ME-2 uses a programming language permitting the solution to be guided toward some possible targets that can be derived from a priori knowledge of sources (chemical profile, ratios, etc.). This feature makes it especially suitable for source apportionment studies where partial knowledge of the sources is available. In the present study ME-2 was applied to data from an urban background site of Barcelona (Spain) to quantify the contribution of road dust resuspension to PM 10 and PM 2.5 concentrations. Given that recently the emission profile of local resuspended road dust was obtained (Amato, F., Pandolfi, M., Viana, M., Querol, X., Alastuey, A., Moreno, T., 2009. Spatial and chemical patterns of PM 10 in road dust deposited in urban environment. Atmospheric Environment 43 (9), 1650-1659), such a priori information was introduced in the model as auxiliary terms of the object function to be minimized by the implementation of the so-called "pulling equations". ME-2 permitted to enhance the basic PMF solution (obtained by PMF2) identifying, beside the seven sources of PMF2, the road dust source which accounted for 6.9 μg m -3 (17%) in PM 10, 2.2 μg m -3 (8%) of PM 2.5 and 0.3 μg m -3 (2%) of PM 1. This reveals that resuspension was responsible of the 37%, 15% and 3% of total

  5. Atmospheric resuspension of radionuclides. Model testing using Chernobyl data

    International Nuclear Information System (INIS)

    Garger, E.; Lev, T.; Talerko, N.; Galeriu, D.; Garland, J.; Hoffman, O.; Nair, S.; Thiessen, K.; Miller, C.; Mueller, H.; Kryshev, A.

    1996-10-01

    Resuspension can be an important secondary source of contamination after a release has stopped, as well as a source of contamination for people and areas not exposed to the original release. The inhalation of resuspended radionuclides contributes to the overall dose received by exposed individuals. Based on measurements collected after the Chernobyl accident, Scenario R was developed to provide an opportunity to test existing mathematical models of contamination resuspension. In particular, this scenario provided the opportunity to examine data and test models for atmospheric resuspension of radionuclides at several different locations from the release, to investigate resuspension processes on both local and regional scales, and to investigate the importance of seasonal variations of these processes. Participants in the test exercise were provided with information for three different types of locations: (1) within the 30-km zone, where local resuspension processes are expected to dominate; (2) a large urban location (Kiev) 120 km from the release site, where vehicular traffic is expected to be the dominant mechanism for resuspension; and (3) an agricultural area 40-60 km from the release site, where highly contaminated upwind 'hot spots' are expected to be important. Input information included characteristics of the ground contamination around specific sites, climatological data for the sites, characteristics of the terrain and topography, and locations of the sampling sites. Participants were requested to predict the average (quarterly and yearly) concentrations of 137 Cs in air at specified locations due to resuspension of Chernobyl fallout; predictions for 90 Sr and 239 + 240 Pu were also requested for one location and time point. Predictions for specified resuspension factors and rates were also requested. Most participants used empirical models for the resuspension factor as a function of time K(t), as opposed to process-based models. While many of these

  6. Atmospheric resuspension of radionuclides. Model testing using Chernobyl data

    Energy Technology Data Exchange (ETDEWEB)

    Garger, E.; Lev, T.; Talerko, N. [Inst. of Radioecology UAAS, Kiev (Ukraine); Galeriu, D. [Institute of Atomic Physics, Bucharest (Romania); Garland, J. [Consultant (United Kingdom); Hoffman, O.; Nair, S.; Thiessen, K. [SENES, Oak Ridge, TN (United States); Miller, C. [Centre for Disease Control, Atlanta, GA (United States); Mueller, H. [GSF - Inst. fuer Strahlenschultz, Neuherberg (Germany); Kryshev, A. [Moscow State Univ. (Russian Federation)

    1996-10-01

    Resuspension can be an important secondary source of contamination after a release has stopped, as well as a source of contamination for people and areas not exposed to the original release. The inhalation of resuspended radionuclides contributes to the overall dose received by exposed individuals. Based on measurements collected after the Chernobyl accident, Scenario R was developed to provide an opportunity to test existing mathematical models of contamination resuspension. In particular, this scenario provided the opportunity to examine data and test models for atmospheric resuspension of radionuclides at several different locations from the release, to investigate resuspension processes on both local and regional scales, and to investigate the importance of seasonal variations of these processes. Participants in the test exercise were provided with information for three different types of locations: (1) within the 30-km zone, where local resuspension processes are expected to dominate; (2) a large urban location (Kiev) 120 km from the release site, where vehicular traffic is expected to be the dominant mechanism for resuspension; and (3) an agricultural area 40-60 km from the release site, where highly contaminated upwind 'hot spots' are expected to be important. Input information included characteristics of the ground contamination around specific sites, climatological data for the sites, characteristics of the terrain and topography, and locations of the sampling sites. Participants were requested to predict the average (quarterly and yearly) concentrations of 137 Cs in air at specified locations due to resuspension of Chernobyl fallout; predictions for 90 Sr and 239 + 240 Pu were also requested for one location and time point. Predictions for specified resuspension factors and rates were also requested. Most participants used empirical models for the resuspension factor as a function of time K(t), as opposed to process-based models. While many of

  7. Observation of sediment resuspension in Old Tampa Bay, Florida

    Science.gov (United States)

    Schoellhamer, David H.; ,

    1990-01-01

    Equipment and methodology have been developed to monitor sediment resuspension at two sites in Old Tampa Bay. Velocities are measured with electromagnetic current meters and suspended solids and turbidity are monitored with optical backscatterance sensors. In late November 1989, a vertical array of instrument pairs was deployed from a permanent platform at a deep-water site, and a submersible instrument package with a single pair of instruments was deployed at a shallow-water site. Wind waves caused resuspension at the shallow-water site, but not at the deeper platform site, and spring tidal currents did not cause resuspension at either site.

  8. Scales of seafloor sediment resuspension in the northern Gulf of Mexico

    Directory of Open Access Journals (Sweden)

    Arne-R. Diercks

    2018-04-01

    Full Text Available Seafloor sediment resuspension events of different scales and magnitudes and the resulting deep (>1,000 m benthic nepheloid layers were investigated in the northern Gulf of Mexico during Fall 2012 to Summer 2013. Time-series data of size-specific 'in-situ' settling speeds of marine snow in the benthic nepheloid layer (moored flux cameras, particle size distributions (profiling camera, currents (various current meters and stacked time-series flux data (sediment traps were combined to recognize resuspension events ranging from small-scale local, to small-scale far-field to hurricane-scale. One small-scale local resuspension event caused by inertial currents was identified based on local high current speeds (>10 cm s–1 and trap data. Low POC content combined with high lithogenic silica flux at 30 m above bottom (mab compared to the flux at 120 mab, suggested local resuspension reaching 30 mab, but not 120 mab. Another similar event was detected by the changes in particle size distribution and settling speeds of particles in the benthic nepheloid layer. Flux data indicated two other small-scale events, which occurred at some distance, rather than locally. Inertia-driven resuspension of material in shallower areas surrounding the traps presumably transported this material downslope leaving a resuspension signal at 120 mab, but not at 30 mab. The passage of hurricane Isaac left a larger scale resuspension event that lasted a few days and was recorded in both traps. Although hurricanes cause large-scale events readily observable in sediment trap samples, resuspension events small in temporal and spatial scale are not easily recognizable in trapped material as they tend to provide less material and become part of the background signal in the long-term averaged trap samples. We suggest that these small-scale resuspension events, mostly unnoticed in conventional time-series sampling, play an important role in the redistribution and ultimate fate of

  9. A theoretical approach to the re-suspension factor

    Directory of Open Access Journals (Sweden)

    Magnoni M.

    2012-04-01

    Full Text Available The atmospheric re-suspension of radionuclides is a well-known phenomenon that consists in the re-injection into the atmosphere of previously deposited radioactivity. The process is driven by the action of wind on surfaces and can act as an additional source of radiation exposure by inhalation, after the deposition has finished. It is thus defined as the re-suspension factor, a parameter K generally considered as a time depending function and defined as the ratio of Ca, the volumetric air activity concentration (Bq m−3 and I0 (Bq m−2, the radioactivity deposition at time zero. The re-suspension factor concept is very useful in radioprotection in order to estimate the inhalation of radionuclides re-suspended from contaminated surfaces when direct atmospheric measurements are lacking or difficult to perform. However, the choice of the proper values of K is usually not a simple task, being quite site-specific and related to the meteorological, géomorphologie and environmental characteristics of the area to be studied. Moreover, several investigations showed clearly that the values of K are a decreasing function of time. For that reason, K values span several orders of magnitude: typical values in the range 10−5–10−10 m−1 are reported in literature for different environmental conditions and time elapsed since the deposition event. The current available models for the re-suspension factor are based on empirical formulas whose parameters are highly site dependent and cannot easily be related to some physical quantity. In this paper a simple physical model for the re-suspension factor is proposed and tested with available environmental radioactivity data (137Cs, collected since 1986 (Chernobyl fallout. The new model not only allows a satisfactory description of the experimental data like even the current empirical models do, but it is also able to connect the K values to quantities with a physical meaning (such as, for example a diffusion

  10. Benthic fluxes of oxygen and inorganic nutrients in the archipelago of Gulf of Finland, Baltic Sea - Effects of sediment resuspension measured in situ

    Science.gov (United States)

    Niemistö, Juha; Kononets, Mikhail; Ekeroth, Nils; Tallberg, Petra; Tengberg, Anders; Hall, Per O. J.

    2018-05-01

    Benthic fluxes of oxygen and dissolved inorganic nutrients; phosphate (DIP), ammonium (NH4), nitrate + nitrite (NOx), and silicate (DSi); and the effects of resuspension on these were studied in situ with the Göteborg benthic landers in the Gulf of Finland archipelago, Baltic Sea. The benthic fluxes were examined at two shallow stations at depths of 7 m and 20 m in May and August 2014. Resuspension altered benthic fluxes of oxygen and nutrients in most of the experiments in August, but not in May, which was mainly due to weaker resuspension treatments in spring. Additionally, the benthic nutrient regeneration rates were higher and redox conditions lower in August when the water was warmer. In August, resuspension increased the benthic oxygen uptake by 33-35%, which was, in addition to stronger resuspension treatment, attributed to higher amounts of dissolved reduced substances in the sediment pore water in comparison to conditions in May. Adsorption onto newly formed iron oxyhydroxides could explain the uptake of DIP by the sediment at the 20 m station and the lowering of the DSi efflux by 31% at the 7 m station during resuspension in August. In addition, resuspension promoted nitrification, as indicated by increased NOx fluxes at both stations (by 30% and 27% at the 7 m and 20 m station, respectively) and a lowered NH4 flux (by 48%) at the 7 m station. Predicted increases in the magnitude and frequency of resuspension will thus markedly affect the transport of phosphorus and silicon and the cycling of nitrogen in the shallow areas of the Gulf of Finland.

  11. Resuspension of fission products from sump water

    International Nuclear Information System (INIS)

    Bunz, H.; Koyro, M.; Propheter, B.; Schoeck, W.; Wagner-Ambs, M.

    1992-11-01

    Resuspension of fission products from the boiling sump in the container has long been known as a source of airborne radioactivity. Since this source is very weak, however, not much attention had been paid to it as long as radiological source terms were governed by stronger sources. Recently, the continuous reduction of source terms and the introduction of accident management measures led to a situation where weak but longlasting sources of radioactivity may become important, either as a contribution to the radiological sources term or as an impact to accident filtration systems. Existing data on resuspension from boiling contaminated water all suffered from two deficiencies: they were measured under conditions unlike those in a reactor accident and they scattered over more than two orders of magnitude. In a precursor study this uncertainty was considered to be too large to use the data for source term calculations. A later experimental research programme REST (REsuspension Source Term) was carried out at the Laboratorium fuer Aerosolphysik und Filtertechnik (LAF), Kernforschungszentrum Karlsruhe (KfK). The programme was supported by the Commission of the European Communities Ispra, under Contract No 3009-86-07 ELISPD in the framework of the shared-cost action programme on reactor safety. The investigations started in 1987 and ended in 1990. The objectives of the REST programme were to measure resuspension source characteristics under simulated accident conditions such that an application of the data in fission product transport and depletion models is possible

  12. Resuspension of the transuranium elements - a review of existing data

    International Nuclear Information System (INIS)

    Linsley, G.S.

    1978-08-01

    Resuspension is an important mechanism in the transfer to man of transuranium elements deposited on surfaces in the environment. In this report the data on resuspension are reviewed, including the limited number of relevant measurements which have been made in the United Kingdom. The various models developed to represent the resuspension process are reviewed and the most appropriate, when site specific data are absent, for application in UK conditions are identified. Recommendations are made on the main areas where further environmental studies are required to enable more reliable predictive models to be developed for application in these conditions. (author)

  13. Study of dust re-suspension at low pressure in a dedicated wind-tunnel

    Science.gov (United States)

    Rondeau, Anthony; Sabroux, Jean-Christophe; Chassefière, Eric

    2015-04-01

    The atmosphere of several telluric planets or satellites are dusty. Such is the case of Earth, Venus, Mars and Titan, each bearing different aeolian processes linked principally to the kinematic viscosity of the near-surface atmosphere. Studies of the Martian atmosphere are particularly relevant for the understanding of the dust re-suspension phenomena at low pressure (7 mbar). It turns out that operation of fusion reactors of the tokamak design produces significant amount of dust through the erosion of plasma-facing components. Such dust is a key issue, both regarding the performance and the safety of a fusion reactor such as ITER, under construction in Cadarache, France. Indeed, to evaluate the explosion risk in the ITER fusion reactor, it is essential to quantify the re-suspended dust fraction as a function of the dust inventory that can be potentially mobilized during a loss of vacuum accident (LOVA), with air or water vapour ingress. A complete accident sequence will encompass dust re-suspension from near-vacuum up to atmospheric pressure. Here, we present experimental results of particles re-suspension fractions measured at 1000, 600 and 300 mbar in the IRSN BISE (BlowIng facility for airborne releaSE) wind tunnel. Both dust monolayer deposits and multilayer deposits were investigated. In order to obtain experimental re-suspension data of dust monolayer deposits, we used an optical microscope allowing to measure the re-suspended particles fraction by size intervals of 1 µm. The deposits were made up of tungsten particles on a tungsten surface (an ubiquitous plasma facing component) and alumina particles on a glass plate, as a surrogate. A comparison of the results with the so-called Rock'nRoll dust re-suspension model (Reeks and Hall, 2001) is presented and discussed. The multilayer deposits were made in a vacuum sedimentation chamber allowing to obtain uniform deposits in terms of thickness. The re-suspension experimental data of such deposits were obtained

  14. Investigations into the resuspension of plutonium in the biosphere

    International Nuclear Information System (INIS)

    Baechmann, K.

    1997-01-01

    In order to compare the resuspension behaviour of Pu with that of other elements, inactive elements were included into the investigations. The following measurements were made: 1. Determination of Pu surface contamination of the ground and of surface concentration of the inactive elements; 2. vertical distributions of the elements in the atmosphere; 3. particle size distributions of the elements; 4. element correlations; 5. determination of resuspension parameters. The measurements were made over a longer period of time in order to detect changes of Pu and of the inactive elements in terms of time and space. With the same resuspension behaviour of Pu and inactive elements, the latter, because of their quick determinability, could serve as model elements to predict Pu behaviour. (orig.) [de

  15. The influence of human physical activity and contaminated clothing type on particle resuspension.

    Science.gov (United States)

    McDonagh, A; Byrne, M A

    2014-01-01

    A study was conducted to experimentally quantify the influence of three variables on the level of resuspension of hazardous aerosol particles from clothing. Variables investigated include physical activity level (two levels, low and high), surface type (four different clothing material types), and time i.e. the rate at which particles resuspend. A mixture of three monodisperse tracer-labelled powders, with median diameters of 3, 5, and 10 microns, was used to "contaminate" the samples, and the resuspended particles were analysed in real-time using an Aerodynamic Particle Sizer (APS), and also by Neutron Activation Analysis (NAA). The overall finding was that physical activity resulted in up to 67% of the contamination deposited on clothing being resuspended back into the air. A detailed examination of the influence of physical activity level on resuspension, from NAA, revealed that the average resuspended fraction (RF) of particles at low physical activity was 28 ± 8%, and at high physical activity was 30 ± 7%, while the APS data revealed a tenfold increase in the cumulative mass of airborne particles during high physical activity in comparison to that during low physical activity. The results also suggest that it is not the contaminated clothing's fibre type which influences particle resuspension, but the material's weave pattern (and hence the material's surface texture). Investigation of the time variation in resuspended particle concentrations indicated that the data were separable into two distinct regimes: the first (occurring within the first 1.5 min) having a high, positive rate of change of airborne particle concentration relative to the second regime. The second regime revealed a slower rate of change of particle concentration and remained relatively unchanged for the remainder of each resuspension event. Copyright © 2013 Elsevier Ltd. All rights reserved.

  16. Resuspension and transport of suspended solids in Eurajoensalmi Bay. Final report of monitoring activities in 2009-2011; Resuspensio ja kiintoaineen kulkeutuminen Eurajoensalmessa. Vesistoemittausten loppuraportti

    Energy Technology Data Exchange (ETDEWEB)

    Mykkanen, J.; Kiirikki, M.; Lindfors, A. [Luode Consulting Oy, Espoo (Finland)

    2012-11-15

    The goal of monitoring activities carried out in Eurajoensalmi Bay was to indentify factors affecting dispersal of river waters and suspended solid matter in the estuary area. In addition to suspended solids load and dispersal of river water, also release of sedimented particles from the sea bed in resuspension was studied. River water quality and discharge as well as resuspension in Eurajoensalmi estuary area were monitored with Luode automatic monitoring stations equipped with water quality, water level, wave height and weather sensors. Dynamics of Eurajoensalmi estuary area was studied by installing profiling current meters (ADCP) and water quality sensors to the sea floor at the mouth of Eurajoensalmi. Spatial variation of surface water quality was monitored with a flow-through method from a moving vessel and manual profiling several times during the monitoring period. Collected data was processed and used in determining suspended solids balance of Eurajoensalmi Bay. The balance was determined by creating a regression model for water exchange and sediment flux over the cross section at the mouth of Eurajoensalmi. Regression model was created also to determine resuspension in Eurajoensalmi area. Sediment flux and resuspension were modeled using long term wind data from Kylmaepihlaja meteorological station as a variable to determine overall sediment balance of Eurajoensalmi.

  17. Evaluation of Resuspension from Propeller Wash in DoD Harbors

    Science.gov (United States)

    2016-05-01

    in ERDC’s Prop-Wash Tank Resuspension by propeller wash from tugboat: in-situ field data: near-bed velocity field, shear stress, critical shear...samples of sediment and water were collected prior to any resuspension event. A C14 Tractor and a slightly smaller Tiger tug boats were used in San

  18. Deposition and Resuspension of Particles

    DEFF Research Database (Denmark)

    Lengweiler, P.; Nielsen, Peter V.; Moser, A.

    To investigate the physical process of deposition and resuspension of particles in the indoor environment, scale experiments are used and a sampling method is established. The influences of surface orientation and turbulence and velocity of the air on the dust load on a surface are analysed....

  19. Physical resuspension and revaporisation phenomena in control rod aerosols

    International Nuclear Information System (INIS)

    Benson, C.G.; Browsher, B.R.

    1988-12-01

    Physical resuspension and revaporisation processes could play a significant role in the transport of fission products in a severe reactor accident. The processes involved in physical resuspension and revaporisation of control rod alloy aerosol particles from a stainless steel substrate have been studied at room temperature under laminar and turbulent flow conditions (Reynolds numbers of between 70 and 7000), and at temperatures in the range from 370 K to 870 K under laminar and intermediate flow conditions (Reynolds numbers of between 7 and 1400) in the absence and presence of steam. The phenomena were investigated using bulk analyses to determine the quantity of material remaining on a coupon after each experiment, and standard surface analysis techniques were used to examine the composition and morphology of the particles. The main conclusions of this work are that: (i) physical resuspension is only significant in turbulent flow, (ii) two processes are involved in physical resuspension: the removal of surface layers which are only loosely bound to the substrate, and the removal of a more tightly-bound layer, (iii) the amount of material resuspended decreases exponentially with time, and the data have been correlated with a reverse isotherm model, (iv) the weight loss from the revaporisation experiments can be interpreted in terms of the effective vapour pressure of the deposit, and an equation has been derived to express this vapour pressure as a function of temperature. These studies have demonstrated the importance of a number of resuspension processes in generating a source of radioactive material that could be released after failure of the containment. Efforts are in hand to include these phenomena in the relevant modelling studies. (author)

  20. Reassessment of Resuspension Factor Following Radionuclide Dispersal: Toward a General-purpose Rate Constant

    Energy Technology Data Exchange (ETDEWEB)

    Marshall, Shaun [Worcester Polytechnic Inst., Worcester, MA (United States). Dept. of Physics; Potter, Charles [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Medich, David [Worcester Polytechnic Inst., Worcester, MA (United States). Dept. of Physics

    2018-05-01

    A recent analysis of historical radionuclide resuspension datasets con rmed the general applicability of the Anspaugh and modified Anspaugh models of resuspension factors following both controlled and disastrous releases. The observations appear to increase in variance earlier in time, however all points were equally weighted in statistical fit calculations, inducing a positive skewing of resuspension coeffcients. Such data are extracted from the available deposition experiments spanning 2900 days. Measurements within a 3-day window are grouped into singular sample sets to construct standard deviations. A refitting is performed using a relative instrumental weighting of the observations. The resulting best-fit equations produces tamer exponentials which give decreased integrated resuspension factor values relative to those reported by Anspaugh. As expected, the fits attenuate greater error amongst the data at earlier time. The reevaluation provides a sharper contrast between the empirical models, and reafirms their deficiencies in the short-lived timeframe wherein the dynamics of particulate dispersion dominate the resuspension process.

  1. Reassessment of Resuspension Factor Following Radionuclide Dispersal: Toward a General-purpose Rate Constant.

    Science.gov (United States)

    Marshall, Shaun; Potter, Charles; Medich, David

    2018-05-01

    A recent analysis of historical radionuclide resuspension datasets confirmed the general applicability of the Anspaugh and modified Anspaugh models of resuspension factors following both controlled and disastrous releases. While observations appear to have larger variance earlier in time, previous studies equally weighted the data for statistical fit calculations; this could induce a positive skewing of resuspension coefficients in the early time-period. A refitting is performed using a relative instrumental weighting of the observations. Measurements within a 3-d window are grouped into singular sample sets to construct standard deviations. The resulting best-fit equations produce tamer exponentials, which give decreased integrated resuspension factor values relative to those reported by Anspaugh. As expected, the fits attenuate greater error among the data at earlier time. The reevaluation provides a sharper contrast between the empirical models and reaffirms their deficiencies in the short-lived timeframe wherein the dynamics of particulate dispersion dominate the resuspension process.

  2. Resuspension parameters for TRAC dispersion model

    International Nuclear Information System (INIS)

    Langer, G.

    1987-01-01

    Resuspension factors for the wind erosion of soil contaminated with plutonium are necessary to run the Rocky Flats Plant Terrain Responsive Atmospheric Code (TRAC). The model predicts the dispersion and resulting population dose due to accidental plutonium releases

  3. A "TEST OF CONCEPT" COMPARISON OF AERODYNAMIC AND MECHANICAL RESUSPENSION MECHANISMS FOR PARTICLES DEPOSITED ON FIELD RYE GRASS (SECALE CERCELE). PART I. RELATIVE PARTICLE FLUX RATES

    Science.gov (United States)

    Resuspension of uniform latex micro spheres deposited on a single seed pod of field rye grass stalk and head was investigated experimentally in a wind tunnel. The experiment was designed to distinguish aerodynamic (viscous and turbulent) mechanisms from mechanical resuspension re...

  4. In situ flume measurements of resuspension in the North Sea

    Science.gov (United States)

    Thompson, C. E. L.; Couceiro, F.; Fones, G. R.; Helsby, R.; Amos, C. L.; Black, K.; Parker, E. R.; Greenwood, N.; Statham, P. J.; Kelly-Gerreyn, B. A.

    2011-07-01

    The in situ annular flume, Voyager II, was deployed at three sites in the North Sea in order to investigate resuspension events, to determine the physical characteristics of the seabed, to determine the threshold of resuspension of the bed and to quantify erosion rates and erosion depths. These are the first controlled, in situ flume experiments to study resuspension in the North Sea, and were combined with long-term measurements of waves and currents. Resuspension experiments were undertaken at two muddy, and one sandy site: north of the Dogger Bank (DG: water depths ˜80 m, very fine, poorly sorted, very fine-skewed sediment experiencing seasonal thermal stratification of the water column along with oxygen depletion); the Oyster Grounds (OG: ˜40 m, similar bed properties, year round water column thermal stratification, Atlantic forcing); and in the Sean Gas Field (SGF: ˜20 m, moderately sorted, very coarse-skewed sand, and well mixed water column). The erosion thresholds of the bed were found to be 0.66-1.04 Pa (DG) and 0.91-1.27 Pa (OG), with corresponding erosion depths of 0.1-0.15 mm and 0.02-0.06 mm throughout the experiments. Evaluation of a year of current velocities from 2007 indicated that at OG, resuspension of the consolidated bed was limited to on average ˜8% of the time as a result of tidal forcing alone for short (properties of the bed. Therefore, while complex variations in biogeophysical factors affected the critical threshold of erosion, once exceeded, erosion rates were related to the nature of the sediment.

  5. Resuspension studies at Bikini Atoll

    International Nuclear Information System (INIS)

    Shinn, J.H.; Homan, D.N.; Robison, W.L.

    1980-02-01

    The following experiments were conducted on Bikini Atoll to provide key parameters for an assessment of inhalation exposure from plutonium-contaminated dust aerosols: (1) a characterization of background (plutonium activity, dust, plutonium, sea spray, and organic aerosol concentrations); (2) a study of plutonium resuspension from a bare field; (3) a study of plutonium resuspension by traffic; and (4) a study of personal inhalation exposure. Dust concentrations of 21 μg m -3 and sea spray of 34 μg m -3 were the background throughout the Bikini Island except within 50 m of the windward beach. Background concentrations of 239+240 Pu were 60 aCi m -3 in the coconut grove and 264 aCi m -3 over rain-stabilized bare soil. The ratio of plutonium activity in aerosols relative to the activity in underlying soil, defined as the enhancement factor, EF, was typically less than one. Enhancement factors increased about 3.8 as a result of tilling. Plutonium resuspension flux was estimated at 0.49 pCi m -2 year -1 over most of Bikini Island. Aerosol size distributions associated with mass and with plutonium activity were typically log-normal with median aerodynamic diameter 2.44 μm, which decreased to 2.0 μm above freshly tilled soil. The Pu concentration in aerosols collected over disturbed soil increased by a factor of 19.1. Vehicular traffic produced dust pulses typically of 10 s duration, 28 μg m -3 average concentration, and plutonium enhancement factor 2.5. Personal dosimetry showed that enhancement of dust by a worker was a factor of 2.64 for heavy work outdoors and 1.86 for light work in and around houses. Pulmonary deposition of plutonium was calculated for various exposure conditions. The pulmonary deposition ranged from 1476 aCi h -1 to 12 aCi h -1

  6. A review: deposition and resuspension processes

    International Nuclear Information System (INIS)

    Sehmel, G.A.

    1979-01-01

    A review chapter was written on deposition and resuspension processes for the forthcoming Department of Energy publication, Atmospheric Sciences and Power Production, edited by D. Randerson. The chapter includes eleven tables and thirteen figures summarizing data from 241 references. The conclusions of that review chapter are given

  7. A sediment resuspension and water quality model of Lake Okeechobee

    Science.gov (United States)

    James, R.T.; Martin, J.; Wool, T.; Wang, P.-F.

    1997-01-01

    The influence of sediment resuspension on the water quality of shallow lakes is well documented. However, a search of the literature reveals no deterministic mass-balance eutrophication models that explicitly include resuspension. We modified the Lake Okeeehobee water quality model - which uses the Water Analysis Simulation Package (WASP) to simulate algal dynamics and phosphorus, nitrogen, and oxygen cycles - to include inorganic suspended solids and algorithms that: (1) define changes in depth with changes in volume; (2) compute sediment resuspension based on bottom shear stress; (3) compute partition coefficients for ammonia and ortho-phosphorus to solids; and (4) relate light attenuation to solids concentrations. The model calibration and validation were successful with the exception of dissolved inorganic nitrogen species which did not correspond well to observed data in the validation phase. This could be attributed to an inaccurate formulation of algal nitrogen preference and/or the absence of nitrogen fixation in the model. The model correctly predicted that the lake is lightlimited from resuspended solids, and algae are primarily nitrogen limited. The model simulation suggested that biological fluxes greatly exceed external loads of dissolved nutrients; and sedimentwater interactions of organic nitrogen and phosphorus far exceed external loads. A sensitivity analysis demonstrated that parameters affecting resuspension, settling, sediment nutrient and solids concentrations, mineralization, algal productivity, and algal stoichiometry are factors requiring further study to improve our understanding of the Lake Okeechobee ecosystem.

  8. MEASURING CONTAMINANT RESUSPENSION RESULTING FROM SEDIMENT CAPPING

    Science.gov (United States)

    This Sediment Issue summarizes two studies undertaken at marine sites by the National Risk Management Research Laboratory of U.S. EPA to evaluate the resuspension of surface materials contaminated with polycyclic aromatic hydrocarbons (PAHs) and polychlorinated biphenyls (PCBs) b...

  9. Development of a resuspension model for contaminated soils. Application to the Palomares area; Desarrollo de un modelo de resuspension de suelos contaminados. Aplicacion al area de Palomares

    Energy Technology Data Exchange (ETDEWEB)

    Garcia-Olivares, A

    1993-07-01

    A model is presented which has been used to simulate the wind resuspension and transport of contaminated soil in the area surrounding the Palomares village, in Southern Spain. The model uses site specific data and some generic parameters as resuspension rate and deposition velocity. The model is able to predict the order of magnitude of the observed air concentration of activity. Some lines of research are suggested which could improve the understanding of the phenomena involved. (Author) 20 refs.

  10. Short-term variability of mineral dust, metals and carbon emission from road dust resuspension

    NARCIS (Netherlands)

    Amato, F.; Schaap, M.; Denier van der Gon, H.A.C.; Pandolfi, M.; Alastuey, A.; Keuken, M.; Querol, X.

    2013-01-01

    Particulate matter (PM) pollution in cities has severe impact on morbidity and mortality of their population. In these cities, road dust resuspension contributes largely to PM and airborne heavy metals concentrations. However, the short-term variation of emission through resuspension is not well

  11. Aerosol resuspension in the reactor cooling system of LWR's under severe accident conditions

    International Nuclear Information System (INIS)

    Alonso, A.; Bolado, R.; Hontanon, E.

    1991-07-01

    Aerosol resuspension from the pipes of the RCS under severe accident conditions happens when the carrier gas flow is turbulent. The origin of such phenomenon seems to be the existence of turbulent bursts in the neighbourhood of the pipe wall. These bursts are of random nature, in space and time. Three theoretical models have been found in available literature; those are: Cleaver and Yates', RESUS and Reeks' models. The first two of them are force balance models, in which particle detachment is supposed whenever aerodynamic lift or drag forces, respectively exceed adhesive forces, and the third one is an energy balance model in which resuspension happens when particle vibrational energy exceeds adhesive potential. From experimental evidence it seems that the studied phenomenon is a force balance problem and RESUS seems to be the most appropriate to it, among the available ones. Small-scale experiments have shown, as main parameters affecting resuspension, the Reynolds number of the flow, aerosol composition and initial loading per unit of area. Moreover, the resuspension rate decreases with time in all experiments where temporal measurements were taken

  12. The release of dissolved nutrients and metals from coastal sediments due to resuspension

    Science.gov (United States)

    Kalnejais, Linda H.; Martin, William R.; Bothner, Michael H.

    2010-01-01

    Coastal sediments in many regions are impacted by high levels of contaminants. Due to a combination of shallow water depths, waves, and currents, these sediments are subject to regular episodes of sediment resuspension. However, the influence of such disturbances on sediment chemistry and the release of solutes is poorly understood. The aim of this study is to quantify the release of dissolved metals (iron, manganese, silver, copper, and lead) and nutrients due to resuspension in Boston Harbor, Massachusetts, USA. Using a laboratory-based erosion chamber, a range of typical shear stresses was applied to fine-grained Harbor sediments and the solute concentration at each shear stress was measured. At low shear stress, below the erosion threshold, limited solutes were released. Beyond the erosion threshold, a release of all solutes, except lead, was observed and the concentrations increased with shear stress. The release was greater than could be accounted for by conservative mixing of porewaters into the overlying water, suggesting that sediment resuspension enhances the release of nutrients and metals to the dissolved phase. To address the long-term fate of resuspended particles, samples from the erosion chamber were maintained in suspension for 90. h. Over this time, 5-7% of the particulate copper and silver was released to the dissolved phase, while manganese was removed from solution. Thus resuspension releases solutes both during erosion events and over a longer timescale due to reactions of suspended particles in the water column. The magnitude of the annual solute release during erosion events was estimated by coupling the erosion chamber results with a record of bottom shear stresses simulated by a hydrodynamic model. The release of dissolved copper, lead, and phosphate due to resuspension is between 2% and 10% of the total (dissolved plus particulate phase) known inputs to Boston Harbor. Sediment resuspension is responsible for transferring a significant

  13. A Review of Dangerous Dust in Fusion Reactors: from Its Creation to Its Resuspension in Case of LOCA and LOVA

    Directory of Open Access Journals (Sweden)

    Andrea Malizia

    2016-07-01

    Full Text Available The choice of materials for the future nuclear fusion reactors is a crucial issue. In the fusion reactors, the combination of very high temperatures, high radiation levels, intense production of transmuting elements and high thermomechanical loads requires very high-performance materials. Erosion of PFCs (Plasma Facing Components determines their lifetime and generates a source of impurities (i.e., in-vessel tritium and dust inventories, which cool down and dilute the plasma. The resuspension of dust could be a consequences of LOss of Coolant Accidents (LOCA and LOss of Vacuum Accidents (LOVA and it can be dangerous because of dust radioactivity, toxicity, and capable of causing an explosion. These characteristics can jeopardize the plant safety and pose a serious threat to the operators. The purpose of this work is to determine the experimental and numerical steeps to develop a numerical model to predict the dust resuspension consequences in case of accidents through a comparison between the experimental results taken from campaigns carried out with STARDUST-U and the numerical simulation developed with CFD codes. The authors in this work will analyze the candidate materials for the future nuclear plants and the consequences of the resuspension of its dust in case of accidents through the experience with STARDUST-U.

  14. Dust resuspension and transport modeling for loss of vacuum accidents

    International Nuclear Information System (INIS)

    Humrickhouse, P.W.; Corradini, M.L.; Sharpe, J.P.

    2007-01-01

    Plasma surface interactions in tokamaks are known to create significant quantities of dust, which settles onto surfaces and accumulates in the vacuum vessel. In ITER, a loss of vacuum accident may result in the release of dust which will be radioactive and/or toxic, and provides increased surface area for chemical reactions or dust explosion. A new method of analysis has been developed for modeling dust resuspension and transport in loss of vacuum accidents. The aerosol dynamic equation is solved via the user defined scalar (UDS) capability in the commercial CFD code Fluent. Fluent solves up to 50 generic transport equations for user defined scalars, and allows customization of terms in these equations through user defined functions (UDF). This allows calculation of diffusion coefficients based on local flow properties, inclusion of body forces such as gravity and thermophoresis in the convection term, and user defined source terms. The code accurately reproduces analytical solutions for aerosol deposition in simple laminar flows with diffusion and gravitational settling. Models for dust resuspension are evaluated, and code results are compared to available resuspension data, including data from the Toroidal Dust Mobilization Experiment (TDMX) at the Idaho National Laboratory. Extension to polydisperse aerosols and inclusion of coagulation effects is also discussed. (orig.)

  15. Resuspension of toxic aerosol using MATHEW--ADPIC wind field--transport and diffusion codes

    International Nuclear Information System (INIS)

    Porch, W.M.

    1979-01-01

    Computer codes have been written which estimate toxic aerosol resuspension based on computed deposition from a primary source, wind, and surface characteristics. The primary deposition pattern and the transport, diffusion, and redeposition of the resuspended toxic aerosol are calculated using a mass-consistent wind field model including topography (MATHEW) and a particle-in-cell diffusion and transport model (ADPIC) which were developed at LLL. The source term for resuspended toxic aerosol is determined by multiplying the total aerosol flux as a function of wind speed by the area of highest concentration and the fraction of suspended material estimated to be toxic. Preliminary calculations based on a test problem at the Nevada Test Site determined an hourly averaged maximum resuspension factor of 10 -4 for a 15 m/sec wind which is within an admittedly large range of resuspension factor measurements using experimental data

  16. Short-term variability of mineral dust, metals and carbon emission from road dust resuspension

    Science.gov (United States)

    Amato, Fulvio; Schaap, Martijn; Denier van der Gon, Hugo A. C.; Pandolfi, Marco; Alastuey, Andrés; Keuken, Menno; Querol, Xavier

    2013-08-01

    Particulate matter (PM) pollution in cities has severe impact on morbidity and mortality of their population. In these cities, road dust resuspension contributes largely to PM and airborne heavy metals concentrations. However, the short-term variation of emission through resuspension is not well described in the air quality models, hampering a reliable description of air pollution and related health effects. In this study we experimentally show that the emission strength of resuspension varies widely among road dust components/sources. Our results offer the first experimental evidence of different emission rates for mineral dust, heavy metals and carbon fractions due to traffic-induced resuspension. Also, the same component (or source) recovers differently in a road in Barcelona (Spain) and a road in Utrecht (The Netherlands). This finding has important implications on atmospheric pollution modelling, mostly for mineral dust, heavy metals and carbon species. After rain events, recoveries were generally faster in Barcelona rather than in Utrecht. The largest difference was found for the mineral dust (Al, Si, Ca). Tyre wear particles (organic carbon and zinc) recovered faster than other road dust particles in both cities. The source apportionment of road dust mass provides useful information for air quality management.

  17. Development of a resuspension model for contaminated soils. Application to the Palomares area

    International Nuclear Information System (INIS)

    Garcia-Olivares, A.

    1993-01-01

    A model is presented which has been used to simulate the wind resuspension and transport of contaminated soil in the area surrounding the Palomares village, in Southern Spain. The model uses site specific data and some generic parameters as resuspension rate and deposition velocity. The model is able to predict the order of magnitude of the observed air concentration of activity. Some lines of research are suggested which could improve the understanding of the phenomena involved. (Author) 20 refs

  18. Evaluation of the transport and resuspension of a simulated nuclear waste slurry: Nuclear Waste Treatment Program

    International Nuclear Information System (INIS)

    Carleson, T.E.; Drown, D.C.; Hart, R.E.; Peterson, M.E.

    1987-09-01

    The Department of Chemical Engineering at the University of Idaho conducted research on the transport and resuspension of a simulated high-level nuclear waste slurry. In the United States, the reference process for treating both defense and civilian HLLW is vitrification using the liquid-fed ceramic melter process. The non-Newtonian behavior of the slurry complicates the evaluation of the transport and resuspension characteristics of the slurry. The resuspension of a simulated (nonradioactive) melter feed slurry was evaluated using a slurry designated as WV-205. The simulated slurry was developed for the West Valley Demonstration Project and was used during a pilot-scale ceramic melter (PSCM) experiment conducted at PNL in July 1985 (PSCM-21). This study involved determining the transport characteristics of a fully suspended slurry and the resuspension characteristics of settled solids in a pilot-scale pipe loop. The goal was to predict the transport and resuspension of a full-scale system based on rheological data for a specific slurry. The rheological behavior of the slurry was evaluated using a concentric cylinder rotational viscometer, a capillary tube viscometer, and the pilot-scale pipe loop. The results obtained from the three approaches were compared. 40 refs., 74 figs., 15 tabs

  19. The Influence of Macrophytes on Sediment Resuspension and the Effect of Associated Nutrients in a Shallow and Large Lake (Lake Taihu, China)

    Science.gov (United States)

    Zhu, Mengyuan; Zhu, Guangwei; Nurminen, Leena; Wu, Tingfeng; Deng, Jianming; Zhang, Yunlin; Qin, Boqiang; Ventelä, Anne-Mari

    2015-01-01

    A yearlong campaign to examine sediment resuspension was conducted in large, shallow and eutrophic Lake Taihu, China, to investigate the influence of vegetation on sediment resuspension and its nutrient effects. The study was conducted at 6 sites located in both phytoplankton-dominated zone and macrophyte-dominated zone of the lake, lasting for a total of 13 months, with collections made at two-week intervals. Sediment resuspension in Taihu, with a two-week high average rate of 1771 g·m-2·d-1 and a yearly average rate of 377 g·m-2·d-1, is much stronger than in many other lakes worldwide, as Taihu is quite shallow and contains a long fetch. The occurrence of macrophytes, however, provided quite strong abatement of sediment resuspension, which may reduce the sediment resuspension rate up to 29-fold. The contribution of nitrogen and phosphorus to the water column from sediment resuspension was estimated as 0.34 mg·L-1 and 0.051 mg·L-1 in the phytoplankton-dominated zone. Sediment resuspension also largely reduced transparency and then stimulated phytoplankton growth. Therefore, sediment resuspension may be one of the most important factors delaying the recovery of eutrophic Lake Taihu, and the influence of sediment resuspension on water quality must also be taken into account by the lake managers when they determine the restoration target. PMID:26030094

  20. Long-term assessment of airborne radiocesium after the Fukushima nuclear accident: re-suspension from bare soil and forest ecosystems

    Science.gov (United States)

    Kajino, Mizuo; Ishizuka, Masahide; Igarashi, Yasuhito; Kita, Kazuyuki; Yoshikawa, Chisato; Inatsu, Masaru

    2016-10-01

    The long-term effect of 137Cs re-suspension from contaminated soil and forests due to the Fukushima nuclear accident has been quantitatively assessed by numerical simulation, a field experiment on dust emission flux in a contaminated area (town of Namie, Fukushima prefecture), and air concentration measurements inside (Namie) and outside (city of Tsukuba, Ibaraki prefecture) the contaminated area. In order to assess the long-term effect, the full year of 2013 was selected to study just after the start of the field experiments. The 137Cs concentrations at Namie and Tsukuba were approximately 10-1-1 and 10-2-10-1 mBq m-3, respectively. The observed monthly median concentration at Namie was 1 to 2 orders of magnitude larger than that at Tsukuba. This observed difference between the two sites was consistent with the simulated difference, indicating successful modeling of 137Cs re-suspension and atmospheric transport. The estimated re-suspension rate was approximately 10-6 day-1, which was significantly lower than the decreasing rate of the ambient gamma dose rate in Fukushima prefecture (10-4-10-3 day-1) as a result of radioactive decay, migration in the soil and biota, and decontamination. Consequently, re-suspension contributed negligibly in reducing ground radioactivity. The dust emission model could reproduce the air concentration of 137Cs in winter, whereas the summer air concentration was underestimated by 1 to 2 orders of magnitude. Re-suspension from forests at a constant rate of 10-7 h-1, multiplied by the green area fraction, could explain the air concentration of 137Cs at Namie and its seasonal variation. The simulated contribution of dust re-suspension to the air concentration was 0.7-0.9 in the cold season and 0.2-0.4 in the warm season at both sites; the remainder of the contribution was re-suspension from forest. The re-suspension mechanisms, especially through the forest ecosystems, remain unknown. This is the first study that provides a crude

  1. Artificial resuspension studies

    International Nuclear Information System (INIS)

    Cooper, B.M.; Marchall, K.B.; Thomas, K.A.; Tracy, B.L.

    1990-01-01

    Artificial resuspension studies on a range of Taranaki and other major trial site soils were performed by use of a mechanical dust-raising apparatus. A cascade impactor was used to analyse airborne dust in terms of mass and 241 Am activities for particle sizes less than 7 μm. Plutonium and americium activities were found to be enhanced in the respirable fraction. Reported enhancement factors (defined as the ratio of activity concentration of the respirable fraction to that of the total soil) ranged from 3.7 to 32.5 for Taranaki soils with an average value of 6 appearing reasonable for general application in outer (plume) areas. Values close to unity were measured at major trial sites , One Tree and Tadje. Results of some experiments where uncontamined dust was raised by activities such as walking and driving over dusty ground are also presented. 7 refs., 9 tabs., 4 figs

  2. STURM: Resuspension mesocosms with realistic bottom shear stress and water column turbulence for benthic-pelagic coupling studies: Design and Applications

    Science.gov (United States)

    Sanford, L. P.; Porter, E.; Porter, F. S.; Mason, R. P.

    2016-02-01

    Shear TUrbulence Resuspension Mesocosm (STURM) tanks, with high instantaneous bottom shear stress and realistic water column mixing in a single system, allow more realistic benthic-pelagic coupling studies that include sediment resuspension. The 1 m3 tanks can be programmed to produce tidal or episodic sediment resuspension over extended time periods (e.g. 4 weeks), over muddy sediments with or without infaunal organisms. The STURM tanks use a resuspension paddle that produces uniform bottom shear stress across the sediment surface while gently mixing a 1 m deep overlying water column. The STURM tanks can be programmed to different magnitudes, frequencies, and durations of bottom shear stress (and thus resuspension) with proportional water column turbulence levels over a wide range of mixing settings for benthic-pelagic coupling experiments. Over eight STURM calibration settings, turbulence intensity ranged from 0.55 to 4.52 cm s-1, energy dissipation rate from 0.0032 to 2.65 cm2 s-3, the average bottom shear stress from 0.0068 to 0.19 Pa, and the instantaneous bottom shear stress from 0.07 to 2.0 Pa. Mixing settings can be chosen as desired and/or varied over the experiment, based on the scientific question at hand. We have used the STURM tanks for four 4-week benthic-pelagic coupling ecosystem experiments with tidal resuspension with or without infaunal bivalves, for stepwise erosion experiments with and without infaunal bivalves, for experiments on oyster biodeposit resuspension, to mimic storms overlain on tidal resuspension, and for experiments on the effects of varying frequency and duration of resuspension on the release of sedimentary contaminants. The large size of the tanks allows water quality and particle measurements using standard oceanographic instrumentation. The realistic scale and complexity of the contained ecosystems has revealed indirect feedbacks and responses that are not observable in smaller, less complex experimental systems.

  3. Inert tracer wind resuspension as a function of wind speed, atmospheric stability, and initial tracer particle size

    International Nuclear Information System (INIS)

    Sehmel, G.A.; Lloyd, F.D.

    1979-01-01

    Wind-caused resuspension rates are being determined in three different, long-term, inert-tracer field experiments. Chemical results were recently received from an accumulated backlog of air filter samples. Resuspension rates are yet to be calculated from these data

  4. Source Term Model for Fine Particle Resuspension from Indoor Surfaces

    National Research Council Canada - National Science Library

    Kim, Yoojeong; Gidwani, Ashok; Sippola, Mark; Sohn, Chang W

    2008-01-01

    This Phase I effort developed a source term model for particle resuspension from indoor surfaces to be used as a source term boundary condition for CFD simulation of particle transport and dispersion in a building...

  5. Long-term assessment of airborne radiocesium after the Fukushima nuclear accident. Re-suspension from bare soil and forest ecosystems

    Energy Technology Data Exchange (ETDEWEB)

    Kajino, Mizuo [Japan Meteorological Agency (JMA), Ibaraki (Japan). Meteorological Research Inst. (MRI); RIKEN Advanced Institute for Computational Science (AICS), Hyogo (Japan); Ishizuka, Masahide [Kagawa Univ. (Japan). Faculty of Engineering; Igarashi, Yasuhito [Japan Meteorological Agency (JMA), Ibaraki (Japan). Meteorological Research Inst. (MRI); Kita, Kazuyuki [Ibaraki Univ. (Japan). Faculty of Science; Yoshikawa, Chisato [Japan Agency for Marine-Earth Science and Technology (JAMSTEC), Kanagawa (Japan); Inatsu, Masaru [Hokkaido Univ., Sapporo (Japan). Faculty of Science

    2016-07-01

    The long-term effect of {sup 137}Cs re-suspension from contaminated soil and forests due to the Fukushima nuclear accident has been quantitatively assessed by numerical simulation, a field experiment on dust emission flux in a contaminated area (town of Namie, Fukushima prefecture), and air concentration measurements inside (Namie) and outside (city of Tsukuba, Ibaraki prefecture) the contaminated area. In order to assess the long-term effect, the full year of 2013 was selected to study just after the start of the field experiments. The {sup 137}Cs concentrations at Namie and Tsukuba were approximately 10{sup -1}-1 and 10{sup -2}-10{sup -1} mBq m{sup -3}, respectively. The observed monthly median concentration at Namie was 1 to 2 orders of magnitude larger than that at Tsukuba. This observed difference between the two sites was consistent with the simulated difference, indicating successful modeling of {sup 137}Cs re-suspension and atmospheric transport. The estimated re-suspension rate was approximately 10{sup -6} day{sup -1}, which was significantly lower than the decreasing rate of the ambient gamma dose rate in Fukushima prefecture (10{sup -4}-10{sup -3} day{sup -1}) as a result of radioactive decay, migration in the soil and biota, and decontamination. Consequently, re-suspension contributed negligibly in reducing ground radioactivity. The dust emission model could reproduce the air concentration of {sup 137}Cs in winter, whereas the summer air concentration was underestimated by 1 to 2 orders of magnitude. Re-suspension from forests at a constant rate of 10{sup -7} h{sup -1}, multiplied by the green area fraction, could explain the air concentration of {sup 137}Cs at Namie and its seasonal variation. The simulated contribution of dust re-suspension to the air concentration was 0.7-0.9 in the cold season and 0.2-0.4 in the warm season at both sites; the remainder of the contribution was re-suspension from forest. The re-suspension mechanisms, especially

  6. Effect of resuspension on the release of heavy metals and water chemistry in anoxic and oxic sediments

    Energy Technology Data Exchange (ETDEWEB)

    Hwang, Kyung-Yup; Kim, Hong-Seok; Hwang, Inseong [School of Civil and Environmental Engineering, Pusan National University, Busan (Korea, Republic of)

    2011-10-15

    Two types of river sediments with contrasting characteristics (anoxic or oxic) were resuspended and the release of heavy metals and changes in water chemistry were investigated. During resuspension of the anoxic sediment, the dissolved oxygen (DO) concentration and redox potential of the water layer decreased abruptly within the first 1 min, followed by increases toward the end of the resuspension period. Heavy metals were released rapidly in the first 6 h, probably due to the oxidation of acid volatile sulfide (AVS) of the anoxic sediment, and then the aqueous phase concentrations of the heavy metals decreased due to resorption onto the sediment until the 12-h point. During resuspension of the oxic sediment, the DO concentration and redox potential remained relatively constant in the oxic ranges. The heavy metals were released from the oxic sediment gradually during a 24-h resuspension period. The temporal maximum concentrations of Ni, Cu, Zn, and Cd in the aqueous phases in both experiments frequently exceeded the USEPA water quality criteria or the water quality guidelines of Australia and New Zealand. This suggests that a resuspension event could bring about temporal water quality deterioration in the two sediment environments. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  7. Characteristics of sediment resuspension in Lake Taihu, China: A wave flume study

    Science.gov (United States)

    Ding, Yanqing; Sun, Limin; Qin, Boqiang; Wu, Tingfeng; Shen, Xia; Wang, Yongping

    2018-06-01

    Lake Taihu is a typical shallow lake which frequently happens sediment resuspension induced by wind-induced waves. The experiments are carried on to simulate the wave disturbance processes in wave flume by setting a series of wave periods (1.2 s, 1.5 s, 1.8 s) and wave heights (2 cm, 10 cm). It aims to analyze the characteristics of sediment resuspension and the mechanisms of nutrients release and to evaluate the effects of sediment dredging on sediment resuspension and nutrients release in Lake Taihu. The results show that wave shear stress during 2 cm and 10 cm wave height processes ranges 0.018-0.023 N/m2 and 0.221-0.307 N/m2, respectively. Wave shear stress has no significant differences between wave periods. Wave height has much more effects on sediment resuspension. Wave height of 2 cm could induce total suspended solids (TSS) reaching up to 5.21 g/m2 and resuspension flux of sediment (M) up to 1.74 g/m2. TSS sharply increases to 30.33-52.41 g/m2 and M reached up to 48.94 g/m2 when wave height reaches to 10 cm. The disturbance depth under different sediment bulk weights ranges from 0.089 to 0.161 mm. Variation of suspended solids in 3 layers (1 cm, 5 cm, 20 cm above sediment interface) has no significant differences. Organic matter, TN and TP have positive relationship with SS. Organic matter is only accounted for 5.7%-7.3% of SS. The experiments under different sediment bulk densities (1.34 g/cm3, 1.47 g/cm3 and 1.59 g/cm3) find that TSS and M fall by 44.2% and 39.8% with sediment bulk density increasing, respectively. Total TN, DTN, TP and DTP decrease by 24.3%-33.6%. It indicates that sediment dredging could effectively reduce SS concentration and nutrient levels in water column. The researches provide a theoretical basis for sediment dredging to control the shore zone of Lake Taihu for lake management.

  8. A Generic Model for the Resuspension of Multilayer Aerosol Deposits by Turbulent Flow

    International Nuclear Information System (INIS)

    Friess, H.; Yadigaroglu, G.

    2001-01-01

    An idealized lattice structure is considered of multilayer aerosol deposits, where every particle at the deposit surface is associated with a resuspension rate constant depending on a statistically distributed particle parameter and on flow conditions. The response of this generic model is represented by a set of integrodifferential equations. As a first application of the general formalism, the behavior of Fromentin's multilayer model is analyzed, and the model parameters are adapted to experimental data. In addition, improved relations between model parameters and physical input parameters are proposed. As a second application, a method is proposed for building multilayer models by using resuspension rate constants of existing monolayer models. The method is illustrated by a sample of monolayer data resulting from the model of Reeks, Reed, and Hall. Also discussed is the error to be expected if a monolayer resuspension model, which works well for thin aerosol deposits, is applied to thick deposits under the classical monolayer assumption that all deposited particles interact with the fluid at all times

  9. The influence of turbulent bursting on sediment resuspension under unidirectional currents

    Directory of Open Access Journals (Sweden)

    S. Salim

    2017-07-01

    Full Text Available Laboratory experiments were conducted in an open channel flume with a flat sandy bed to examine the role of turbulence on sediment resuspension. An acoustic Doppler velocimeter (ADV was used to measure the instantaneous three-dimensional velocity components and acoustic backscatter as a proxy to suspended sediment concentration. Estimates of sediment transport assume that there is a mean critical velocity that needs to be exceeded before sediment transport is initiated. This approach does not consider the turbulent flow field that may initiate sediment resuspension through event-based processes such as the bursting phenomenon. In this paper, laboratory measurements were used to examine the sediment resuspension processes below and above the mean critical velocity. The results within a range above and below the measured mean critical velocity suggested that (1 the contribution of turbulent bursting events remained identical in both experimental conditions, (2 ejection and sweep events contributed more to the total sediment flux than up-acceleration and down-deceleration events, and (3 wavelet transform revealed a correlation between the momentum and sediment flux in both test conditions. Such similarities in conditions above and below the measured mean critical velocity highlight the need to re-evaluate the accuracy of a single time-averaged mean critical velocity for the initiation of sediment entrainment.

  10. Dust in HTRs: Its nature and improving prediction of its resuspension

    Energy Technology Data Exchange (ETDEWEB)

    Kissane, M.P., E-mail: martin.kissane@irsn.fr [Institut de Radioprotection et de Surete Nucleaire, Division de la Prevention des Accidents Majeurs, BP 3, 13115 Saint-Paul-lez-Durance (France); Zhang, F. [Institut de Radioprotection et de Surete Nucleaire, Division de la Prevention des Accidents Majeurs, BP 3, 13115 Saint-Paul-lez-Durance (France); University of Newcastle, School of Mechanical and Systems Engineering, Stephenson Building, Claremont Road, Newcastle-upon-Tyne NE1 7RU (United Kingdom); Reeks, M.W. [University of Newcastle, School of Mechanical and Systems Engineering, Stephenson Building, Claremont Road, Newcastle-upon-Tyne NE1 7RU (United Kingdom)

    2012-10-15

    The HTR primary-system environment comprises nuclear graphites, alloys, dust (primarily carbonaceous) and high-purity helium. The amount of carbonaceous dust produced in a pebble-bed system would be considerably greater than one using a prismatic core with a significant contribution arising from the partially-graphitized binder of the pebbles. The dust is very fine, <10 {mu}m in size. Experience with HTRs shows the primary system to be contaminated by the isotopes {sup 134}Cs, {sup 137}Cs, {sup 90}Sr, {sup 110m}Ag, {sup 131}I, {sup 135}Xe, {sup 85}Kr and tritium at a level representing an occupational-health issue rather than a safety issue. However, strong sorption of caesium, strontium, iodine and tritium onto carbonaceous dust has been observed. Hence, the extent to which deposited dust can be resuspended during a depressurization accident is a safety issue since the dust comprises the main vector for release of radioactivity into the confinement. For fine dust on a surface, the principal force keeping it in place arises from inter-molecular (van der Waals) forces while aerodynamic forces, mainly drag, act to remove it. The reference model chosen here for improving resuspension predictions is the so-called Rock'n'Roll model. This model is based on a statistical approach leading to a resuspension rate for the escape of particles from a potential well via the action of the fluctuating aerodynamic force caused by turbulence. The as-published Rock'n'Roll model assumes that the fluctuations of the aerodynamic force obey a Gaussian distribution. Here, we introduce calculated statistics for the fluctuations taken from a large-eddy simulation of turbulent channel flow (work is in progress on generating these statistics using direct numerical simulation of turbulence). The overall influence of more-realistic (non-Gaussian) forces on the resuspension rate is found to be an increase in short-term resuspension. Given this and the fact that the adhesive

  11. A test of resuspension factor models against Chernobyl data

    International Nuclear Information System (INIS)

    Garger, E.K.; Hoffman, F.O.

    1995-04-01

    After the accident at Unit 4 of the Chernobyl nuclear power plant (NPP), stationary air samplers were operated at Chernobyl and Baryshevka, cities which are 16 km and 150 km, respectively, from the NPP. Other air samplers were operated simultaneously, but intermittently, at locations within the 30 km zone at distances of 4-25 km from the NPP. These data were used to check the validity of time dependent models of the resuspension factor K (m -1 ). Seven different models were examined, three of which are discussed in the paper. Data from the stationary air samplers were averaged over one day or one month; dam from the intermittent air samplers were averaged over three days in 1986 and over four hours in 1991. The concentrations of eight radionuclides were measured at ten points during the same time period (14-17 September 1986). The calculated resuspension factors range from 6 x 10 -9 m -1 to 3 x 10 -6 m -1 . Data for the spatial means of K are given for certain time periods in 1986 and 1991; also presented are the calculated values according to the models. The experimental data and the calculated values differ by up to more than one order of magnitude. Also analysed was the temporal change in experimental values of K and these values were compared with model predictions. The annual means of the resuspension factor as determined experimentally and as calculated with the models are presented. The model derived from empirical data measured in Neuherberg after the Chernobyl accident agrees best with the data. The Garland model systematically gives results lower than the experimental values, and the calculated values of K from the Linsley model are consistently conservative. Also considered were the uncertainty of K due to fluctuations in air concentrations and possible biological effects of episodic exposures

  12. A test of resuspension factor models against Chernobyl data

    Energy Technology Data Exchange (ETDEWEB)

    Garger, E.K. [Ukrainian Academy of Agricultural Sciences, Kiev (Ukraine). Inst. of Radioecology; Anspaugh, L.R.; Shinn, J.H. [Lawrence Livermore National Lab., CA (United States); Hoffman, F.O. [Senes Oak Ridge, Inc., TN (United States)

    1995-04-01

    After the accident at Unit 4 of the Chernobyl nuclear power plant (NPP), stationary air samplers were operated at Chernobyl and Baryshevka, cities which are 16 km and 150 km, respectively, from the NPP. Other air samplers were operated simultaneously, but intermittently, at locations within the 30 km zone at distances of 4-25 km from the NPP. These data were used to check the validity of time dependent models of the resuspension factor K (m{sup -1}). Seven different models were examined, three of which are discussed in the paper. Data from the stationary air samplers were averaged over one day or one month; dam from the intermittent air samplers were averaged over three days in 1986 and over four hours in 1991. The concentrations of eight radionuclides were measured at ten points during the same time period (14-17 September 1986). The calculated resuspension factors range from 6 x 10{sup -9} m{sup -1} to 3 x 10{sup -6} m{sup -1}. Data for the spatial means of K are given for certain time periods in 1986 and 1991; also presented are the calculated values according to the models. The experimental data and the calculated values differ by up to more than one order of magnitude. Also analysed was the temporal change in experimental values of K and these values were compared with model predictions. The annual means of the resuspension factor as determined experimentally and as calculated with the models are presented. The model derived from empirical data measured in Neuherberg after the Chernobyl accident agrees best with the data. The Garland model systematically gives results lower than the experimental values, and the calculated values of K from the Linsley model are consistently conservative. Also considered were the uncertainty of K due to fluctuations in air concentrations and possible biological effects of episodic exposures.

  13. Resuspension of uranium-plutonium oxide particles from burning Plexiglas

    International Nuclear Information System (INIS)

    Pickering, S.

    1987-01-01

    Nuclear fuel materials such as Uranium-Plutonium oxide must be handled remotely in gloveboxes because of their radiotoxicity. These gloveboxes are frequently constructed largely of combustible Plexiglas sheet. To estimate the potential airborne spread of radioactive contamination in the event of a glovebox fire, the resuspension of particles from burning Plexiglas was investigated. (author)

  14. Particle deposition and resuspension in gas-cooled reactors—Activity overview of the two European research projects THINS and ARCHER

    Energy Technology Data Exchange (ETDEWEB)

    Barth, T., E-mail: t.barth@hzdr.de [Institute of Fluid Dynamics, Helmholtz-Zentrum Dresden-Rossendorf, Bautzner Landstraße 400, 01328 Dresden (Germany); Lecrivain, G. [Institute of Fluid Dynamics, Helmholtz-Zentrum Dresden-Rossendorf, Bautzner Landstraße 400, 01328 Dresden (Germany); Jayaraju, S.T. [Nuclear Research and Consultancy Group (NRG), 1755ZG Petten (Netherlands); Hampel, U. [Institute of Fluid Dynamics, Helmholtz-Zentrum Dresden-Rossendorf, Bautzner Landstraße 400, 01328 Dresden (Germany); AREVA Endowed Chair of Imaging Techniques in Energy and Process Engineering, Technische Universität Dresden, 01062 Dresden (Germany)

    2015-08-15

    Highlights: • A summary on particle deposition and resuspension experiments is provided. • Similarities between single and multilayer particle deposits are found. • Numerical models for simulation of particle deposits are successfully developed. - Abstract: The deposition and resuspension behaviour of radio-contaminated aerosol particles is a key issue for the safety assessment of depressurization accidents of gas-cooled high temperature reactors. Within the framework of two European research projects, namely Thermal Hydraulics of Innovative Nuclear Systems (THINS) and Advanced High-Temperature Reactors for Cogeneration of Heat and Electricity R&D (ARCHER), a series of investigations was performed to investigate the transport, the deposition and the resuspension of aerosol particles in turbulent flows. The experimental and numerical tests can be subdivided into four different parts: (1) Monolayer particle deposition, (2) Monolayer particle resuspension, (3) Multilayer particle deposition and (4) Multilayer particle resuspension. The experimental results provide a new insight into the formation and removal of aerosol particle deposits in turbulent flows and are used for the development and validation of numerical procedures in gas-cooled reactors. Good agreement was found between the numerical and the experimental results.

  15. Plutonium: resuspension of aerosols in nuclear installations: bibliographic survey

    International Nuclear Information System (INIS)

    Guetat, Ph.; Monfort, M.; Armand, P.; Alloul-Marmor, L.

    2006-01-01

    This document presents an analysis and a bibliographical synthesis of the studies on resuspension factors for plutonium. It aims at helping the engineers of safety to specify the scenarios of accidents which relate to their activities and to bring elements justified for the definition of their term-source 'installation' in the safety reports of the installations. (authors)

  16. Resuspension of polychlorinated biphenyl-contaminated field sediment: release to the water column and determination of site-specific K DOC.

    Science.gov (United States)

    Friedman, Carey L; Lohmann, Rainer; Burgess, Robert M; Perron, Monique M; Cantwell, Mark G

    2011-02-01

    Sediments from the New Bedford Harbor (NBH) U.S. Environmental Protection Agency (U.S. EPA) Superfund site (Massachusetts, USA), contaminated with polychlorinated biphenyls (PCBs), were resuspended under different water column redox conditions: untreated, oxidative, and reductive. The partitioning of PCBs to the overlying water column was measured with polyethylene samplers and compared to partitioning without resuspension. Greater concentrations of total aqueous (freely dissolved + dissolved organic carbon (DOC)-associated) PCBs were found in all resuspended treatments for PCBs with mid-range K(OW)s, but no difference was observed in total aqueous concentrations among different redox conditions. The magnitude of increased concentrations depended on resuspension time and congener K(OW), but ranged from approximately one to eight times those found without resuspension. In a parallel study, DOC was flocculated and removed from smaller-scale NBH sediment resuspensions. In situ K(DOC)s were determined and used to calculate freely dissolved and DOC-associated fractions of the increase in total aqueous PCB concentrations due to resuspension. The importance of DOC-associated PCBs increased with increasing K(OW). In situ K(DOC)s were approximately one to two orders of magnitude greater than those calculated with a commonly used linear free energy relationship (LFER). The present study demonstrates that resuspension of contaminated sediments releases PCBs to the water column, of which a significant fraction are DOC-associated (e.g., 28, 65, and 90% for PCBs 28, 66, and 110, respectively). Results also imply that site-specific PCB K(DOC)s are superior to those calculated with generic LFERs. © 2010 SETAC.

  17. Sediment Resuspension by Ship Traffic in Newark Bay, New Jersey

    Science.gov (United States)

    2015-04-01

    Army Corps of Engineers ENV Report 37. Dellapenna, T. M., A. A. Mead, G. A. Gill, R. D. Lehman, and K. W. Warnken, 2006. The impact of shrimp ... larvae . Journal of Great Lakes Research 20(2):366-376. Schoellhamer, D. H. 1996. Anthropogenic sediment resuspension mechanisms in a shallow

  18. Transuranic and tracer simulant resuspension. [/sup 238/Pu, /sup 239/Pu, /sup 240/Pu

    Energy Technology Data Exchange (ETDEWEB)

    Sehmel, G. A.

    1977-07-01

    Plutonium resuspension results are summarized for experiments conducted at Rocky Flats, onsite on the Hanford reservation, and for winds blowing from offsite onto the Hanford reservation near the Prosser barricade boundary. In each case, plutonium resuspension was shown by increased airborne plutonium concentrations as a function of either wind speed or as compared to fallout levels. All measured airborne concentrations were below maximum permissible concentrations (MPC). Both plutonium and cesium concentrations on airborne soil were normalized by the quantity of airborne soil sampled. Airborne radionuclide concentrations in ..mu..Ci/g were related to published values for radionuclide concentrations on surface soils. For this ratio of radionuclide concentration per gram on airborne soil divided by that for ground surface soil, there are eight orders of magnitude uncertainty from 10/sup -4/ to 10/sup 4/. Horizontal plutonium fluxes on airborne nonrespirable soils at all three sites were bracketed within the same three to four orders of magnitude from 10/sup -7/ to 10/sup -3/ ..mu..Ci/(m/sup 2/ day) for plutonium-239 and 10/sup -8/ to 10/sup -5/ ..mu..Ci/(m/sup 2/ day) for plutonium-238. These are the entire experimental base for nonrespirable airborne plutonium transport. Airborne respirable plutonium-239 concentrations increased with wind speed for a southeast wind direction coming from offsite near the Hanford reservation Prosser barricade. Airborne plutonium fluxes on nonrespirable particles had isotopic ratios, /sup 240/Pu//sup 239 +240/Pu, similar to weapons grade plutonium rather than fallout plutonium. Resuspension rates were summarized for controlled inert particle tracer simulant experiments. Wind resuspension rates for tracers increased with wind speed to about the fifth power.

  19. Atmospheric Radionuclides from the FDNPP Accident-Four years' observations in Tsukuba, Japan and immediate resuspension

    Science.gov (United States)

    Igarashi, Yasuhito; Kajino, Mizuo; Zaizen, Yuji; Adachi, Kouji; Mikami, Masao

    2015-04-01

    The accident of Fukushima Dai-Ichi Nuclear Power Plant (FDNPP) of the Tokyo Electric Power Corporation arisen by the hit of great earthquake and tsunami in March 11, 2011, emitted abundant fresh radioactive material to the atmospheric environment. With 4-years' observation for the Fukushima radioactivity at the Meteorological Research Institute, Japan (MRI) the persisting resuspension has been observed. The resuspension seems still in difficulty to give forecast by computer modeling; the observations are indispensable bodies of the research even in the future. As a primary approach, immediate re-suspension factors were roughly estimated with modeled deposition amounts by the first plume to the Kanto district and the observed minimum activity concentration between two plume events, i.e. Mar 17 09JST to Mar. 20 09JST, by assuming mass closure between re-suspension from the contaminated surface and outflow by horizontal advection and turbulence vertical mixing as follows: Diki ΔCi- Δ2Ci- Δz = U Δx + Kz Δz2 , where i indicates radionuclides namely 137Cs and 131I, Diindicates modeled total (gas+aerosol) cumulative deposition (Bq/m2) by Mar 17 09JST, ki is the re-suspension factor (/s), U and Kz are modeled space- and time- averaged horizontal wind speed (m/s) and vertical turbulent diffusivity (m2/s), respectively, Ci indicates time-averaged observed concentration of radionuclides (9.75×10-4 and 3.14×10-1 Bq/m3 for 137Cs and 131I, respectively), and Δx and Δz are horizontal and vertical length of space where the above mass closure is obtained. In order to obtain the horizontal and vertical gradient terms on the right hand of the equation, concentrations outside the space are assumed zero (no inflow to the space). The re-suspension factors for 137Cs and 131I are 7.0×10-6 and 5.3×10-4 (/s), respectively, for the smallest volume of space (Δx and Δz are 3 km and 100 m, respectively). Those for 137Cs and 131I varied 1.6×10-6-1.5×10-5 (6.1×10-6 on average) and

  20. Response patterns of phytoplankton growth to variations in resuspension in the German Bight revealed by daily MERIS data in 2003 and 2004

    Directory of Open Access Journals (Sweden)

    Jian Su

    2015-10-01

    Full Text Available Chlorophyll (chl a concentration in coastal seas exhibits variability on various spatial and temporal scales. Resuspension of particulate matter can somewhat limit algal growth, but can also enhance productivity because of the intrusion of nutrient-rich pore water from sediments or bottom water layers into the whole water column. This study investigates whether characteristic changes in net phytoplankton growth can be directly linked to resuspension events within the German Bight. Satellite-derived chl a were used to derive spatial patterns of net rates of chl a increase/decrease (NR in 2003 and 2004. Spatial correlations between NR and mean water column irradiance were analysed. High correlations in space and time were found in most areas of the German Bight (R2 > 0.4, suggesting a tight coupling between light availability and algal growth during spring. These correlations were reduced within a distinct zone in the transition between shallow coastal areas and deeper offshore waters. In summer and autumn, a mismatch was found between phytoplankton blooms (chl a > 6 mg m−3 and spring-tidal induced resuspension events as indicated by bottom velocity, suggesting that there is no phytoplankton resuspension during spring tides. It is instead proposed here that frequent and recurrent spring-tidal resuspension events enhance algal growth by supplying remineralized nutrients. This hypothesis is corroborated by a lag correlation analysis between resuspension events and in-situ measured nutrient concentrations. This study outlines seasonally different patterns in phytoplankton productivity in response to variations in resuspension, which can serve as a reference for modelling coastal ecosystem dynamics.

  1. Experimental studies on the resuspension of plutonium from aged sources at the Nevada Test Site

    International Nuclear Information System (INIS)

    Anspaugh, L.R.; Phelps, P.L.; Kennedy, N.C.; Shinn, J.H.; Reichman, J.M.

    1976-01-01

    Measurements of 239 240 Pu concentrations in air, distributions with particle size, and saltation fluxes were carried out at the GMX area of the Nevada Test Site, an area contaminated with plutonium nearly 20 years prior to the measurements. At the center of the source, the concentrations were directly proportional to the square of the friction velocity as expected on the basis of collateral dust concentration measurements. Healy's model of transport and diffusion was used to derive values of the resuspension rate from these measurements. The resuspension rates varied from 2.7 x 10 -12 to 4.8 x 10 -10 sec -1 . Much of the variance was removed by normalizing the resuspension rate to the cube of the friction velocity. The activity median aerodynamic diameter of the plutonium aerosol varied from 1.6 to 8 μm, which corresponds to calculated pulmonary depositions of 25 and 15 percent, respectively. The movement of soil in saltation at this site was generally not significant. Measured fluxes were less than 10 -5 g/cm-sec averaged over the long time periods required to accumulate a measurable sample

  2. Time dependence of the 137Cs resuspension factor on the Romanian territory after the Chernobyl accident

    International Nuclear Information System (INIS)

    Mihaila, B.; Cuculeanu, V.

    1994-01-01

    On the basis of the radioactivity levels in aerosol and atmospheric deposition samples due to the Chernobyl accident, the resuspension factor of 137 Cs as a four-parameter function has been inferred. The standard procedure to derive the dependence of resuspension on time assumes that the initial deposit is instantaneous. A simple method assuming a constant deposition rate over a fixed period has been proposed. Also, based on existing experimental data, an attempt was made to consider a realistic time dependence of the deposition rate to cope with the particular case of the Chernobyl accident. The differences between the two models are outlined. The Chernobyl direct deposit has been assumed to be the deposit measured between 30 April and 30 June 1986. The calculated values of the resuspension factor are consistent with the IAEA's recommended model and depend on the rainfall that occurred in June 1986 and the site-specific disturbance conditions during the first 100 d following 1 July 1986 and only on artificial disturbance by humans and vehicles after that. 16 refs., 5 figs., 3 tabs

  3. Resuspension and spreading of 137 Cs in urban areas: the Goiania experience

    International Nuclear Information System (INIS)

    Rio, M.A.P. do.

    1993-01-01

    The characteristics of the Goiania accident (a restricted and local contamination) together with the fact that the region has received no contribution from the Chernobyl accident, neither from the atomic tests represents an unique opportunity to study the behaviour of 147 Cs at an urban area. The study of the resuspension and deposition processes of the 137 Cs associated to surface soil was performed at a house at the 57th. street near the main primary focus. It was decided to use the two gardens of the house, where continuous measurements of aerosol and total deposition took place. Impactor measurements were also performed to evaluate the size distribution of particles in the air. The results as a whole suggests a very complex pattern for the 137 Cs resuspension and deposition in Goiania, indicating to be these mechanisms local,phenomena and without evidences of a significant spreading of 137 Cs from the places of primary contamination. (author). 63 refs., 14 figs., 9 tabs

  4. Impact of natural (waves and currents) and anthropogenic (trawl) resuspension on the export of particulate matter to the open ocean: Application to the Gulf of Lion (NW Mediterranean)

    Science.gov (United States)

    Ferré, B.; Durrieu de Madron, X.; Estournel, C.; Ulses, C.; Le Corre, G.

    2008-08-01

    Modern sediment deposits on continental margins form a vast reservoir of particulate matter that is regularly affected by resuspension processes. Resuspension by bottom trawling on shelves with strong fishing activity can modify the scale of natural disturbance by waves and currents. Recent field data show that the impact of bottom trawls on fine sediment resuspension per unit surface is comparable with that of the largest storms. We assessed the impact of both natural and anthropogenic processes on the dispersal of riverborne particles and shelf sediments on the Gulf of Lion shelf. We performed realistic numerical simulations of resuspension and transport forced by currents and waves or by a fleet of bottom trawlers. Simulations were conducted for a 16-month period (January 1998-April 1999) to characterise the seasonal variability. The sediment dynamics takes into account bed armoring, ripple geometry and the cohesive and non-cohesive characteristics of the sediments. Essential but uncertain parameters (clay content, erosion fluxes and critical shear stress for cohesive sediment) were set with existing data. Resuspension by waves and currents was controlled by shear stress, whereas resuspension by trawls was controlled by density and distribution of the bottom trawler fleet. Natural resuspension by waves and currents mostly occurred during short seasonal episodes, and was concentrated on the inner shelf. Trawling-induced resuspension, in contrast, occurred regularly throughout the year and was concentrated on the outer shelf. The total annual erosion by trawls (5.6×10 6 t y -1, t for metric tonnes) was four orders of magnitude lower than the erosion induced by waves and currents (35.3×10 9 t y -1). However the net resuspension (erosion/deposition budget) for trawling (0.4×10 6 t y -1) was only one order of magnitude lower than that for waves and currents (9.2×10 6 t y -1). Off-shelf export concerned the finest fraction of the sediment (clays and fine silts

  5. Residual β activity of particulate 234Th as a novel proxy for tracking sediment resuspension in the ocean

    Science.gov (United States)

    Lin, Wuhui; Chen, Liqi; Zeng, Shi; Li, Tao; Wang, Yinghui; Yu, Kefu

    2016-01-01

    Sediment resuspension occurs in the global ocean, which greatly affects material exchange between the sediment and the overlying seawater. The behaviours of carbon, nutrients, heavy metals, and other pollutants at the sediment-seawater boundary will further link to climate change, eutrophication, and marine pollution. Residual β activity of particulate 234Th (RAP234) is used as a novel proxy to track sediment resuspension in different marine environments, including the western Arctic Ocean, the South China Sea, and the Southern Ocean. Sediment resuspension identified by high activity of RAP234 is supported by different lines of evidence including seawater turbidity, residence time of total 234Th, Goldschmidt’s classification, and ratio of RAP234 to particulate organic carbon. A conceptual model is proposed to elucidate the mechanism for RAP234 with dominant contributions from 234Th-238U and 212Bi-228Th. The ‘slope assumption’ for RAP234 indicated increasing intensity of sediment resuspension from spring to autumn under the influence of the East Asian monsoon system. RAP234 can shed new light on 234Th-based particle dynamics and should benefit the interpretation of historical 234Th-238U database. RAP234 resembles lithophile elements and has broad implications for investigating particle dynamics in the estuary-shelf-slope-ocean continuum and linkage of the atmosphere-ocean-sediment system. PMID:27252085

  6. Residual β activity of particulate (234)Th as a novel proxy for tracking sediment resuspension in the ocean.

    Science.gov (United States)

    Lin, Wuhui; Chen, Liqi; Zeng, Shi; Li, Tao; Wang, Yinghui; Yu, Kefu

    2016-06-02

    Sediment resuspension occurs in the global ocean, which greatly affects material exchange between the sediment and the overlying seawater. The behaviours of carbon, nutrients, heavy metals, and other pollutants at the sediment-seawater boundary will further link to climate change, eutrophication, and marine pollution. Residual β activity of particulate (234)Th (RAP234) is used as a novel proxy to track sediment resuspension in different marine environments, including the western Arctic Ocean, the South China Sea, and the Southern Ocean. Sediment resuspension identified by high activity of RAP234 is supported by different lines of evidence including seawater turbidity, residence time of total (234)Th, Goldschmidt's classification, and ratio of RAP234 to particulate organic carbon. A conceptual model is proposed to elucidate the mechanism for RAP234 with dominant contributions from (234)Th-(238)U and (212)Bi-(228)Th. The 'slope assumption' for RAP234 indicated increasing intensity of sediment resuspension from spring to autumn under the influence of the East Asian monsoon system. RAP234 can shed new light on (234)Th-based particle dynamics and should benefit the interpretation of historical (234)Th-(238)U database. RAP234 resembles lithophile elements and has broad implications for investigating particle dynamics in the estuary-shelf-slope-ocean continuum and linkage of the atmosphere-ocean-sediment system.

  7. The roles of resuspension, diffusion and biogeochemical processes on oxygen dynamics offshore of the Rhône River, France: a numerical modeling study

    Science.gov (United States)

    Moriarty, Julia M.; Harris, Courtney K.; Fennel, Katja; Friedrichs, Marjorie A. M.; Xu, Kehui; Rabouille, Christophe

    2017-04-01

    Observations indicate that resuspension and associated fluxes of organic material and porewater between the seabed and overlying water can alter biogeochemical dynamics in some environments, but measuring the role of sediment processes on oxygen and nutrient dynamics is challenging. A modeling approach offers a means of quantifying these fluxes for a range of conditions, but models have typically relied on simplifying assumptions regarding seabed-water-column interactions. Thus, to evaluate the role of resuspension on biogeochemical dynamics, we developed a coupled hydrodynamic, sediment transport, and biogeochemical model (HydroBioSed) within the Regional Ocean Modeling System (ROMS). This coupled model accounts for processes including the storage of particulate organic matter (POM) and dissolved nutrients within the seabed; fluxes of this material between the seabed and the water column via erosion, deposition, and diffusion at the sediment-water interface; and biogeochemical reactions within the seabed. A one-dimensional version of HydroBioSed was then implemented for the Rhône subaqueous delta in France. To isolate the role of resuspension on biogeochemical dynamics, this model implementation was run for a 2-month period that included three resuspension events; also, the supply of organic matter, oxygen, and nutrients to the model was held constant in time. Consistent with time series observations from the Rhône Delta, model results showed that erosion increased the diffusive flux of oxygen into the seabed by increasing the vertical gradient of oxygen at the seabed-water interface. This enhanced supply of oxygen to the seabed, as well as resuspension-induced increases in ammonium availability in surficial sediments, allowed seabed oxygen consumption to increase via nitrification. This increase in nitrification compensated for the decrease in seabed oxygen consumption due to aerobic remineralization that occurred as organic matter was entrained into the water

  8. The spread of 137Cs by resuspension of contaminated soil in the urban area of Goiania

    International Nuclear Information System (INIS)

    Pires do Rio, M.A.; Amaral, E.C.S.; Paretzke, H.G.

    2000-01-01

    Measurements regarding the population exposure were performed in Goiania after the radiological accident as well as studies on resuspension and redeposition of 137 Cs in urban areas, on the contribution of soil splash to the 137 Cs uptake by leafy vegetables and on the transfer of 137 Cs from soil to chicken meat and eggs. Periodical street dust sampling was used to follow-up the spreading of the radionuclide in the city. The results do not indicate a measurable spreading of this radionuclide throughout the city from the contaminated areas, but resuspension can lead to significant local contamination of agricultural products, equipment, structures, etc. (author)

  9. Evaluation of Resuspension from Propeller Wash in DoD Harbors

    Science.gov (United States)

    2016-09-01

    for Applications ( VBA ) code, accessible within Microsoft® Excel®, was used to generate the WHAM7 input file with all parameter combinations. Details...rpm and above. High sediment concentration during resuspension made optical access to the laser sheet impossible. Most PIV measurements were not...blocked the optical access . During that time we can observe a sudden increase of streamwise velocity from about 0.3 to 0.5 m/s, according to the ADV

  10. First experimental results of particle re-suspension in a low pressure wind tunnel applied to the issue of dust in fusion reactors

    Energy Technology Data Exchange (ETDEWEB)

    Rondeau, Anthony, E-mail: anthony.rondeau@irsn.fr [Institut de Radioprotection et de Sûreté Nucléaire (IRSN), PSN-RES/SCA, Gif-sur-Yvette 91192 (France); Merrison, Jonathan; Iversen, Jens Jacob [Department of Physics and Astronomy, Institute for Storage Ring Facilities, 8000 Aarhus C (Denmark); Peillon, Samuel; Sabroux, Jean-Christophe; Lemaitre, Pascal; Gensdarmes, François [Institut de Radioprotection et de Sûreté Nucléaire (IRSN), PSN-RES/SCA, Gif-sur-Yvette 91192 (France); Chassefière, Eric [Laboratoire Géosciences Paris Sud (GEOPS), UMR 8148, Université Paris Sud, 91403 Orsay Cedex (France)

    2015-10-15

    Highlights: • The first experimental data of dust re-suspension performed by controlled airflow (in terms of airflow velocity and fluid density). • The effect of the surrounding pressure in the re-suspension mechanism. • The friction (shear velocity) reduction at low pressure in the transient regime (Knudsen number close to one). • The importance of the adhesion forces between particles in dust mobilization by clustering. • The fact that the existing re-suspension models of the relevant literature do not take into account this clustering phenomenon. - Abstract: During the normal operating condition of the future ITER tokamak, a massive production of dust in the toroidal vacuum vessel is expected. This dust, originating from the erosion of tungsten and beryllium internal walls of the torus by the plasma, would be mobilized to some extent during a loss of vacuum accident (LOVA). For safety reasons, it is essential to quantify the re-suspended dust fraction during such an event. Here, we provide preliminary experimental data of dust re-suspension obtained in the wind tunnel of the European Space Agency (ESA) at low pressures (300, 130 and 10 mbar). The experimentations were performed with multilayer deposits. We used two powders with a median diameter at 15.5 μm and 21.8 μm. A negative influence of the low pressure in the re-suspension mechanism is observed. For example, given a re-suspension fraction of 10%, increasing friction shear velocities are derived for decreasing absolute pressures: 300 mbar/0.66 m s{sup −1}; 130 mbar/1.08 m s{sup −1}; and 10 mbar/1.84 m s{sup −1}. In addition, we highlight the friction reduction for Kundsen numbers greater than 0.1 by an analysis of the airflow forces.

  11. Particles in wall-bounded turbulent flows deposition, re-suspension and agglomeration

    CERN Document Server

    Pozorski, Jacek

    2017-01-01

    The book presents an up-to-date review of turbulent two-phase flows with the dispersed phase, with an emphasis on the dynamics in the near-wall region. New insights to the flow physics are provided by direct numerical simuation and by fine experimental techniques. Also included are models of particle dynamics in wall-bounded turbulent flows, and a description of particle surface interactions including muti-layer deposition and re-suspension.

  12. Ash resuspension related to the 2011-2012 Cordón Caulle eruption, Chile, in a rural community of Patagonia, Argentina

    Science.gov (United States)

    Forte, Pablo; Domínguez, Lucia; Bonadonna, Costanza; Gregg, Chris E.; Bran, Donaldo; Bird, Deanne; Castro, Jonathan M.

    2018-01-01

    The 2011-2012 Cordón Caulle eruption emitted about 1 km3 of rhyodacitic tephra. Dominant westerly winds in the region caused most of the primary tephra to deposit in neighboring Argentina. In addition to the impact of widespread dispersal and fallout of primary tephra during the eruption, Argentina was also significantly affected by remobilization of the primary ash even several years after the climactic phase of the eruption. In this mixed methods study, we combine aspects of natural and social sciences to characterize the ash resuspension events associated with the 2011-2012 Cordón Caulle deposits and assess the impacts on the Argentinian farming community of Ingeniero Jacobacci in the Patagonian Steppe. Our findings show the primary importance of wind, rainfall and ash availability in controlling the occurrence and persistence of ash resuspension events. The role played by these variables was also reflected in the seasonal distribution of events observed. Regarding the impacts, our results complement those of earlier studies and demonstrate that ash resuspension events can exacerbate the negative impact of primary tephra fallout events from the time of deposition to many years after the eruption. Only after five years has the environment and the farming community begun to show signs of recovery. Our findings also highlight the importance of assessing ash resuspension events in multi-hazard scenarios involving volcanic and hydrometeorologic hazards.

  13. Dry deposition and resuspension of particulate matter in city environments

    International Nuclear Information System (INIS)

    Jensen, N.O.

    1984-06-01

    The report describes, mostly in qualitative terms, the deposition and resuspension of particles and how the mechanics depend on particle size. The effect of rough surfaces is discussed. It is concluded that knowledge on the subject, at relevant large Reynolds numbers, is indeed lacking. Various methods for measurements of deposition is mentioned and further the report gives some general ideas on how a suitable full scale experiment should be laid out in order to produce some data on the problems of dry deposition to city surfaces. (author)

  14. Advanced receptor modelling for the apportionment of road dust resuspension to atmospheric PM

    Science.gov (United States)

    Amato, F.; Pandolfi, M.; Escrig, A.; Querol, X.; Alastuey, A.; Pey, J.; Perez, N.; Hopke, P. K.

    2009-04-01

    Fugitive emissions from traffic resuspension can often represent an important source of atmospheric particulate matter in urban environments, especially when the scarce precipitations favour the accumulation of road dust. Resuspension of road dust can lead to high exposures to heavy metals, metalloids and mineral matter. Knowing the amount of its contribution to atmospheric PM is a key task for establishing eventual mitigation or preventive measures. Factor analysis techniques are widely used tools for atmospheric aerosol source apportionment, based on the mass conservation principle. Paatero and Tapper (1993) suggested the use of a Weighted Least Squares scheme with the aim of obtaining a minimum variance solution. Additionally they proposed to incorporate the basic physical constraint of non negativity, calling their approach Positive Matrix Factorization (PMF), which can be performed by the program PMF2 released by Paatero (1997). Nevertheless, Positive Matrix Factorization can be either solved with the Multilinear Engine (ME-2), a more flexible program, also developed by Paatero (1999), which can solve any model consisting in sum of products of unknowns. The main difference with PMF2 is that ME-2 does not solve only well-defined tasks, but its actions are defined in a "script file" written in a special-purpose programming language, allowing incorporating additional tasks such as data processing etc. Thus in ME-2 a priori information, e.g. chemical fingerprints can be included as auxiliary terms of the object function to be minimized. This feature of ME-2 make it especially suitable for source apportionment studies where some knowledge (chemical ratios, profiles, mass conservation etc) of involved sources is available. The aim of this study was to quantify the contribution of road dust resuspension in PM10, PM2.5 and PM1 data set from Barcelona (Spain). Given that recently the emission profile of local road dust was characterized (Amato et al., in press

  15. SUPPLEMENTARY COMPARISON: Final report on APMP.PR-S1.1: Bilateral comparison of irradiance responsivity of UVA detectors

    Science.gov (United States)

    Huang, Xuebo

    2009-01-01

    In order to assess the performance of the standards and techniques used for calibration and measurement of UVA irradiance responsivity of photodetectors in NMISA, South Africa, a new comparison was decided as a follow-up to comparison APMP.PR-S1. It is registered in the Key Comparison Data Base (KCDB) of BIPM as a bilateral supplementary comparison, with the identifier APMP.PR-S1.1. The comparison was carried out following the same technical protocol as that of supplementary comparison APMP PR-S1. The principle, organization and method of the comparison, as well as the preliminary measurements at the pilot laboratory NMC-A*STAR Singapore, were described in the Final Report of the APMP.PR-S1 comparison. The results of this bilateral comparison show that the NMISA's results lie within ±2% against the comparison reference values of APMP.PR-S1, which is a great improvement. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the APMP, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

  16. Organic matter sedimentation and resuspension in Tilapia (Oreochromis niloticus) fish ponds during a growing cycle

    NARCIS (Netherlands)

    Jimenez-Montealegre, R.; Verdegem, M.C.J.; Zamora, J.E.; Verreth, J.A.J.

    2002-01-01

    The rates of sedimentation and resuspension of organic carbon and total nitrogen were measured in earthen fishponds, based on nutrient input, water quality parameters and fish size and biomass. Material collected in sediment traps and soil samples were analyzed for organic carbon, total nitrogen,

  17. Resuspension of fission products during severe accidents in light-water reactors

    International Nuclear Information System (INIS)

    Borkowski, R.; Bunz, H.; Schoeck, W.

    1986-05-01

    This report investigates the influence of resuspension phenomena on the overall radiological source term of core melt accidents in a pressurized water reactor. A review of the existing literature is given and the literature data are applied to calculations of the source term. A large scatter in the existing data was found. Depending on the scenario and on the data set chosen for the calculations the relative influence of resuspended fission products on the source term ranges from dominant to negligible. (orig.) [de

  18. Re-suspension of Cesium-134/137 into the Canadian Environment and the Contribution Stemming from the Fukushima-Daiichi Nuclear Incident

    Science.gov (United States)

    Mercier, Jean-Francois; Zhang, Weihua; Loignon-Houle, Francis; Cooke, Michael W.; Ungar, Kurt R.; Pellerin, Eric R.

    2013-04-01

    Cesium-137 (t1/2 = 30 yr) and cesium-134 (t1/2 = 2yr) constitute major fission by-products observed as the result of a nuclear incident. Such radioisotopes become integrated into the soil and biomass, and can therefore undergo re-suspension into the environment via activities such as forest fires. The Canadian Radiological Monitoring Network (CRMN), which consists of 26 environmental monitoring stations spread across the country, commonly observes cesium-137 in air filters due to re-suspension of material originating from long-past weapons testing. Cesium-134 is not observed owing to its relatively short half-life. The Fukushima-Daiichi nuclear power plant incident of March 2011 caused a major release of radioactive materials into the environment. In Canada, small quantities of both cesium-137 and cesium-134 fallout were detected with great frequency in the weeks which followed, falling off rapidly beginning in July 2011. Since September 2011, the CRMN has detected both cesium-137 and cesium-134 from air filters collected at Yellowknife, Resolute, and Quebec City locations. Using the known initial cesium-134/cesium-137 ratio stemming from this incident, along with a statistical assessment of the normality of the data distribution, we herein present evidence that strongly suggests that these activity spikes are due to re-suspended hot particles originating from the Fukushima-Daiichi nuclear power plant incident. Moreover, we have evidence to suggest that this re-suspension is localized in nature. This study provided empirical insight into the transport and uptake of radionuclides over vast distances, and it demonstrates that the CRMN was able to detect evidence of a re-suspension of Fukushima-Daiichi related isotopes.

  19. Characteristics of phosphorus fractionated from the sediment resuspension in abrupt expansion flow experiments

    Institute of Scientific and Technical Information of China (English)

    Jun Wan; Ze Wang; Hezhong Yuan

    2010-01-01

    Phosphorous (P) fraction characteristics in sediment resuspension were investigated under adequately hydrodynamic conditions.Four forms of P in overlying water,including dissolved inorganic P,dissolved total P,total P,and particulate P,and six fractions of P in suspended particulate matter (SPM),including loosely sorbed P (NH4Cl-P),redox-sensitive P (BD-P),aluminum-bound P (Al-P),organic P (NaOH-nrP),calcium-bound P (Ca-P) and residual P (Res-P),were quantified,respectively.Different hydrodynamic conditions resulted in different P form changes.Four states could be ascribed:(1) P desorption by sediment and SPM,and P adsorption by overlying water;(2) P desorption by SPM,and P adsorption by overlying water;(3) P adsorption by SPM,and P desorption by overlying water;and (4) P equilibrium between SPM and overlying water.The contents of P in overlying water acquired peak values in the middle position of the vertical P distribution due to the combined actions of SPM and sediment.P fractions in SPM were in the following order:BD-P>NaOH-nrp>Ca-P>Al-P>Res-P>NH4CI-P.BD-P in SPM frequently exchanged with P forms in overlying water.Resuspension was favorable to forming Ca-P in SPM.

  20. Use of fallout radionuclides ((7)Be, (210)Pb) to estimate resuspension of Escherichia coli from streambed sediments during floods in a tropical montane catchment.

    Science.gov (United States)

    Ribolzi, Olivier; Evrard, Olivier; Huon, Sylvain; Rochelle-Newall, Emma; Henri-des-Tureaux, Thierry; Silvera, Norbert; Thammahacksac, Chanthamousone; Sengtaheuanghoung, Oloth

    2016-02-01

    Consumption of water polluted by faecal contaminants is responsible for 2 million deaths annually, most of which occur in developing countries without adequate sanitation. In tropical aquatic systems, streambeds can be reservoirs of persistent pathogenic bacteria and high rainfall can lead to contaminated soils entering streams and to the resuspension of sediment-bound microbes in the streambed. Here, we present a novel method using fallout radionuclides ((7)Be and (210)Pbxs) to estimate the proportions of Escherichia coli, an indicator of faecal contamination, associated with recently eroded soil particles and with the resuspension of streambed sediments. We show that using these radionuclides and hydrograph separations we are able to characterize the proportion of particles originating from highly contaminated soils and that from the resuspension of particle-attached bacteria within the streambed. We also found that although overland flow represented just over one tenth of the total flood volume, it was responsible for more than two thirds of the downstream transfer of E. coli. We propose that data obtained using this method can be used to understand the dynamics of faecal indicator bacteria (FIB) in streams thereby providing information for adapted management plans that reduce the health risks to local populations. Graphical Abstract Graphical abstract showing (1) the main water flow processes (i.e. overland flow, groundwater return flow, blue arrows) and sediment flow components (i.e. resuspension and soil erosion, black arrows) during floods in the Houay Pano catchment; (2) the general principle of the method using fallout radionuclide markers (i.e. (7)Be and (210)Pbxs) to estimate E. coli load from the two main sources (i.e. streambed resuspension vs soil surface washoff); and 3) the main results obtained during the 15 May 2012 storm event (i.e. relative percentage contribution of each process to the total streamflow, values in parentheses).

  1. The resuspension and redeposition of 137Cs in an urban area: the experience after the Goiania accident

    International Nuclear Information System (INIS)

    Pires Do Rio, M.A.; Amaral, E.C.S.; Paretzke, H.G.

    1994-01-01

    In Goiania, Brazil, the accidental opening of a 137 Cs teletherapy source led to the contamination of an urban area of approximately 1 km 2 . The restricted, local contamination patterns without any significant influence from previous contaminations (Chernobyl reactor accident and atmospheric atomic bomb test fall-out) provided a unique opportunity to study the resuspension and redeposition mechanisms in an urban area under tropical climate characteristics. Air, total deposition, rainwater, surface soil and street dust were sampled over 2 years at a garden of a house and the surroundings and analysed for 137 Cs. The local meteorological conditions were recorded. In addition, some size fractionation measurements were performed. The data show a significant seasonality and a very slow long-term decrease with time for the activity concentration in air and deposition rate. The data as a whole suggest that in Goiania, resuspension and deposition are mainly local phenomena and no evidence was found for a significant spreading of 137 Cs from the place of primary contamination. (author)

  2. Particulate Matter Resuspension in Mississippi Bight Evaluated with CONCORDE's Synthesis Model

    Science.gov (United States)

    O'Brien, S. J.; Quas, L. M.; Miles, T. N.; Pan, C.; Cambazoglu, M. K.; Soto Ramos, I. M.; Greer, A. T.; Church, I.; Wiggert, J. D.

    2017-12-01

    The CONsortium for oil spill exposure pathways in COastal River-Dominated Ecosystems (CONCORDE) was established to investigate the complex fine-scale biological, chemical and physical interactions in a marine system controlled by pulsed-river plume dynamics. During CONCORDE's spring 2016 field campaign, the In Situ Ichthyoplankton Imaging System (ISIIS) on the R/V Point Sur and the Scanfish on the R/V Pelican comprehensively characterized the physical and biological structure in the region. Increased suspended particulate matter was observed by the ISIIS, with concentrations at depth sufficient to completely occlude the in situ images of planktonic organisms. Data was also collected on the continental shelf during the spring cruise by the RU31 glider in the proximity of the Mississippi River Delta, east of the ISIIS / Scanfish transects. Backscatter and salinity observed by the Scanfish and glider showed elevated suspended particulate matter and increased salinity, suggesting a linkage to shoreward advection from the continental shelf of oceanic waters that are sufficiently energetic to drive sediment resuspension. As part of the CONCORDE research effort, a four-dimensional biogeochemical/lower trophic level synthesis model for Mississippi Sound and Bight has been developed, based on the Coupled Ocean-Atmosphere-Wave-Sediment Transport (COAWST) Modeling System. This study utilizes CONCORDE's synthesis model to investigate the physical forcing mechanisms affecting the increased suspended particulate matter concentration observed in the Mississippi Bight during spring 2016, and advection pathways between estuarine and shelf waters in the northern Gulf of Mexico. The results show that episodic, advection-driven resuspension is a critical aspect controlling suspended sediment distributions in Mississippi Bight, which has implications for observed spatio-temporal patterns of planktonic species.

  3. Atmospheric deposition, resuspension and root uptake of plutonium in corn and other grain-producing agroecosystems near a nuclear fuel facility

    International Nuclear Information System (INIS)

    Pinder, J.E. III; McLeod, K.W.; Adriano, D.C.; Corey, J.C.; Boni, A.L.

    1989-01-01

    Plutonium released to the environment may contribute to dose to humans through inhalation or ingestion of contaminated foodstuffs. Plutonium contamination of agricultural plants may result from interception and retention of atmospheric deposition, resuspension of Pu-bearing soil particles to plant surfaces, and root uptake and translocation to grain. Plutonium on vegetation surfaces may be transferred to grain surfaces during mechanical harvesting. Data obtained from corn grown near the US Department of Energy's H-Area nuclear fuel chemical separations facility on the Savannah River Site was used to estimated parameters of a simple model of Pu transport in agroecosystems. The parameter estimates for corn were compared to those previously obtained for wheat and soybeans. Despite some differences in parameter estimates among crops, the relative importances of atmospheric deposition, resuspension and root uptake were similar among crops. For even small deposition rates, the relative importances of processes for Pu contamination of corn grain should be: transfer of atmospheric deposition from vegetation surfaces to grain surfaces during combining > resuspension of soil to grain surfaces > root uptake. Approximately 3.9 x 10 -5 of a year's atmospheric deposition is transferred to grain. Approximately 6.2 x 10 -9 of the Pu inventory in the soil is resuspended to corn grain, and a further 7.3 x 10 -10 of the soil inventory is absorbed by roots and translocated to grains

  4. Resuspension and estuarine nutrient cycling: insights from the Neuse River Estuary

    Directory of Open Access Journals (Sweden)

    D. R. Corbett

    2010-10-01

    Full Text Available For at least the past several decades, North Carolina's Neuse River Estuary (NRE has been subject to water quality problems relating to increased eutrophication. Research initiated in the past several years have addressed the nutrient processes of the water column and the passive diffusion processes of the benthic sedimentary environment. Resuspension of bottom sediments, by bioturbation, tides, or winds, may also have a significant effect on the flux of nutrients in an estuarine system These processes can result in the advective transport of sediment porewater, rich with nitrogen, phosphorus and carbon, into the water column. Thus, estimates of nutrient and carbon inputs from the sediments may be too low.

    This study focused on the potential change in bottom water nutrient concentrations associated with measured resuspension events. Previous research used short-lived radionuclides and meteorological data to characterize the sediment dynamics of the benthic system of the estuary. These techniques in conjunction with the presented porewater inventories allowed evaluation of the depth to which sediments have been disturbed and the advective flux of nutrients to the water column. The largest removal episode occurred in the lower NRE as the result of a wind event and was estimated that the top 2.2 cm of sediment and corresponding porewater were removed. NH4+ advective flux (resuspended was 2 to 6 times greater than simply diffusion. Phosphate fluxes were estimated to be 15 times greater than the benthic diffusive flux. Bottom water conditions with elevated NH4+ and PO43− indicate that nutrients stored in the sediments continue to play an important role in overall water quality and this study suggests that the advective flux of nutrients to the water column is critical to understand estuarine nutrient cycling.

  5. Resuspension studies in the Marshall Islands.

    Science.gov (United States)

    Shinn, J H; Homan, D N; Robison, W L

    1997-07-01

    The contribution of inhalation exposure to the total dose for residents of the Marshall Islands was monitored at occasions of opportunity on several islands in the Bikini and Enewetak Atolls. To determine the long-term potential for inhalation exposure, and to understand the mechanisms of redistribution and personal exposure, additional investigations were undertaken on Bikini Island under modified and controlled conditions. Experiments were conducted to provide key parameters for the assessment of inhalation exposure from plutonium-contaminated dust aerosols: characterization of the contribution of plutonium in soil-borne aerosols as compared to sea spray and organic aerosols, determination of plutonium resuspension rates as measured by the meteorological flux-gradient method during extreme conditions of a bare-soil vs. a stabilized surface, determination of the approximate individual exposures to resuspended plutonium by traffic, and studies of exposures to individuals in different occupational environments simulated by personal air sampling of workers assigned to a variety of tasks. Enhancement factors (defined as ratios of the plutonium-activity of suspended aerosols relative to the plutonium-activity of the soil) were determined to be less than 1 (typically 0.4 to 0.7) in the undisturbed, vegetated areas, but greater than 1 (as high as 3) for the case studies of disturbed bare soil, roadside travel, and for occupational duties in fields and in and around houses.

  6. Final report on CCM key comparison CCM.D-K2: Comparison of liquid density standards

    Science.gov (United States)

    Bettin, Horst; Jacques, Claude; Zelenka, Zoltán; Fujii, Ken-ichi; Kuramoto, Naoki; Chang, Kyung-Ho; Lee, Yong Jae; Becerra, Luis Omar; Domostroeva, Natalia

    2013-01-01

    The results are presented of the key comparison CCM.D-K2 that covered the density measurements of four liquids: the density of water at 20 °C, of pentadecane at 15 °C, 20 °C, 40 °C and 60°C, of tetrachloroethlyene at 5 °C and 20 °C and of a viscous oil at 20 °C. Seven national metrology institutes measured the densities at atmospheric pressure by hydrostatic weighing of solid density standards in the time interval from 27 April 2004 to 28 June 2004. Since the participants were asked not to include components for a possible drift or inhomogeneity of the liquid in their uncertainty budget, these uncertainty contributions are investigated for the final evaluation of the data. For this purpose, results of stability and homogeneity measurements of the pilot laboratory are used. The participants decided not to include a possible drift of the liquid's density since no significant drift could be detected, and the influence of the drift and its uncertainty are negligible. Similarly, the inhomogeneity of the water and pentadecane samples is not significant and has no influence on the evaluation. Thus, it was neglected. Only the inhomogeneities of tetrachloroethylene and of the viscous oil were significant. Consequently, they were included in the evaluation. With one or two exceptions, the results show good agreement among the participants. Only in the case of water are the results clearly discrepant. The key comparison reference values were calculated by the weighted mean (taking into account a small correlation between two participants) in the case of consistent results. Otherwise the Procedure B of Cox was used. The expanded uncertainties of all reference densities are below 1 × 10-5 in relative terms. This satisfies the needs of all customers who wish to calibrate or check liquid density measuring instruments such as oscillation-type density meters. The comparison fully supports the calibration measurement capabilities table in the BIPM key comparison database

  7. Migration of two antibiotics during resuspension under simulated wind-wave disturbances in a water-sediment system.

    Science.gov (United States)

    Li, Shu; Huang, Zheng; Wang, Yi; Liu, Yu-Qing; Luo, Ran; Shang, Jing-Ge; Liao, Qian-Jia-Hua

    2018-02-01

    In this study, the migration of antibiotics (norfloxacin, NOR; and sulfamethoxazole, SMX) under simulated resuspension conditions across the sediment-water interface were quantified for two locations in China: point A, located in Meiliang Bay of Lake Taihu, and point B, located in Dapukou of Lake Taihu. The concentrations of suspended solids (SS) in the overlying water amounted to 100, 500, and 1000 mg/L during background, moderate, and strong simulated wind-wave disturbances, respectively. At each SS level, the initial concentrations of the two antibiotics were set to 1, 5, and 10 mg/L. The results showed that both resuspended SS and the initial concentration of antibiotics could influence the migration of NOR in the water-sediment system. Specifically, both higher SS and initial antibiotic concentrations were associated with higher rates of migration and accumulation of NOR from water to sediment. In contrast, the migration of SMX in the water-sediment system was not impacted by SS or initial antibiotic concentration. The adsorption capacities of sediments for NOR and SMX were significantly different at both locations, possibly reflecting differences in cation exchange capacity (CEC) and organic material (OM) contents. In general, higher CEC and OM values were found in sediments with a higher adsorption capacity for the antibiotics. When CEC and OM values of sediments were higher, the adsorption capacity reached up to 51.73 mg/kg. Large differences in the migration from water to sediment were observed for the two antibiotics, with NOR migration rates higher than those of SMX. The accumulation of NOR in surface sediment during resuspension was about 14 times higher than that of SMX. The main reason for this is that the chemical adsorption of NOR is seldom reversible. Overall, this study demonstrates that resuspension of NOR and SMX attached to sediments under simulated wind-wave disturbances can promote the migration of the antibiotics from water to sediment

  8. Remobilization of polycyclic aromatic hydrocarbons and organic matter in seawater during sediment resuspension experiments from a polluted coastal environment: Insights from Toulon Bay (France).

    Science.gov (United States)

    Guigue, Catherine; Tedetti, Marc; Dang, Duc Huy; Mullot, Jean-Ulrich; Garnier, Cédric; Goutx, Madeleine

    2017-10-01

    Polycyclic aromatic hydrocarbons (PAHs) and organic matter contents were measured in seawater during resuspension experiments using sediments collected from Toulon Bay (Northwestern Mediterranean Sea, France). The studied sediments were very highly contaminated in PAHs, especially in 4-ring compounds emitted from combustion processes. The sediments used for resuspension experiments were collected at 0-2 cm (diagenetically new organic matter, OM) and 30-32 cm depths (diagenetically transformed OM). They were both mostly composed of fine particles (seawater up to 10-, 1.3-, 4.4- and 5.7-fold, respectively. The remobilization in seawater was higher for 4-6 ring PAHs, especially benzo(g,h,i)perylene, whose concentration exceeded the threshold values of the European Water Framework Directive. This noted the potential harmful effects of sediment resuspension on marine biota. From these sediment resuspension experiments, we determined OC-normalized partition coefficients of PAHs between sediment and water (K oc ) and found that during such events, the transfer of PAHs from sediment particles to seawater was lower than that predicted from octanol-water partition coefficients (K ow ) (i.e., measured K oc  > K oc predicted from K ow ). The results confirmed the sequestration role of sedimentary OC quality and grain size on PAHs; the OM diagenetic state seemed to impact the partition process but in a relatively minor way. Furthermore, differences were observed between 2-4 ring and 5-6 ring PAHs, with the latter displaying a relatively higher mobility towards seawater. These differences may be explained by the distribution of these two PAH pools within different OM moieties, such as humic substances and black carbon. Copyright © 2017 Elsevier Ltd. All rights reserved.

  9. Resuspension and settling of helminth eggs in water: Interactions with cohesive sediments.

    Science.gov (United States)

    Sengupta, Mita E; Andersen, Thorbjørn J; Dalsgaard, Anders; Olsen, Annette; Thamsborg, Stig M

    2012-08-01

    Helminth parasite eggs in low quality water represent main food safety and health hazards and are therefore important indicators used to determine whether such water can be used for irrigation. Through sedimentation helminth eggs accumulate in the sediment, however resuspension of deposited helminth eggs will lead to increased concentration of suspended eggs in the water. Our study aimed to determine the erodibility (erosion rate and erosion threshold) and settling velocity of Ascaris and Trichuris eggs as well as cohesive sediment at different time points after incorporation into the sediment. Cohesive sediment collected from a freshwater stream was used to prepare a sediment bed onto which helminth eggs were allowed to settle. The erodibility of both sediment and helminth eggs was found to decrease over time indicating that the eggs were incorporated into the surface material of the bed and that this material was stabilized through time. This interaction between eggs and bulk sediment was further manifested in an increased settling velocity of suspended eggs when sediment was present in the suspension as compared to a situation with settling in clean water. The incorporation into the sediment bed and the aggregation with sediment particles decrease the mobility of both helminth egg types. Our findings document that helminth eggs should not be viewed as single entities in water systems when modelling the distribution of eggs since both erodibility and settling velocity of eggs are determined by mobility of the sediment present in the water stream. Recalculation of the erosion threshold for helminth eggs and sediment showed that even at relatively low current velocities i.e. 0.07-0.12ms(-1) newly deposited eggs will be mobile in open irrigation channels. These environmental factors affecting resuspension must be taken into account when developing models for sedimentation of helminth eggs in different water systems. Copyright © 2012 Elsevier Ltd. All rights

  10. Final radioactive waste disposal: A European comparison of organization and costs

    International Nuclear Information System (INIS)

    Drasdo, P.

    2000-01-01

    The investigation is aimed to the comparison of organization structures of operators (plants) and governmental institutions concerned with the final disposal of radioactive waste. The study is covering Germany, France, United Kingdom and Sweden. The capital amount of total final disposal costs are the highest in Germany, the lowest in Sweden. This is also true for the final disposal costs that have to be financed by electricity production from nuclear power plants. The reasons for the differences with respect to economic efficiencies, political decisions and technical concepts are discussed

  11. Quantitative microbial risk assessment (QMRA) shows increased public health risk associated with exposure to river water under conditions of riverbed sediment resuspension

    CSIR Research Space (South Africa)

    Abia

    2016-10-01

    Full Text Available of The Total Environment, 556-557, pp 1143-1151 Quantitative microbial risk assessment (QMRA) shows increased public health risk associated with exposure to river water under conditions of riverbed sediment resuspension Akebe Luther King Abia a...

  12. Final report on RMO Vickers key comparison COOMET M.H-K1

    Science.gov (United States)

    Aslanyan, E.; Menelao, F.; Herrmann, K.; Aslanyan, A.; Pivovarov, V.; Galat, E.; Dovzhenko, Y.; Zhamanbalin, M.

    2013-01-01

    This report describes a COOMET key comparison on Vickers hardness scales involving five National Metrology Institutes: PTB (Germany), BelGIM (Belarus), NSC IM (Ukraine), KazInMetr (Kazakhstan) and VNIIFTRI (Russia). The pilot laboratory was VNIIFTRI, and PTB acted as the linking institute to key comparisons CCM.H-K1.b and CCM.H-K1.c conducted for the Vickers hardness scales HV1 and HV30, respectively. The comparison was also conducted for the HV5 Vickers hardness scale, since this scale is most frequently used in practice in Russia and CIS countries that work according to GOST standards. In the key comparison, two sets of hardness reference blocks for the Vickers hardness scales HV1, HV5 and HV30 consisting each of three hardness reference blocks with hardness levels of 450 HV and 750 HV were used. The measurement results and uncertainty assessments for HV1 and HV30 hardness scales, as announced by BelGIM, NSC IM, KazInMetr and VNIIFTRI, are in good agreement with the key comparison reference values of CCM.H-K1.b and CCM.H-K1.c. The comparison results for the HV5 hardness scale are viewed as additional information, since up to today no CCM key comparisons on this scale have yet been carried out. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

  13. KEY COMPARISON: Final report of comparison of the calibrations of hydrometers for liquid density determination between SIM laboratories: SIM.M.D-K4

    Science.gov (United States)

    Becerra, Luis Omar

    2009-01-01

    This SIM comparison on the calibration of high accuracy hydrometers was carried out within fourteen laboratories in the density range from 600 kg/m3 to 1300 kg/m3 in order to evaluate the degree of equivalence among participant laboratories. This key comparison anticipates the planned key comparison CCM.D-K4, and is intended to be linked with CCM.D-K4 when results are available. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCM, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

  14. Plutonium concentrations in airborne soil at Rocky Flats and Hanford determined during resuspension experiments

    International Nuclear Information System (INIS)

    Sehmel, G.A.

    1978-01-01

    Plutonium resuspension results are summarized for experiments conducted by the author at Rocky Flats, onsite on the Hanford reservation, and for winds blowing from offsite onto the Hanford reservation near the Prosser barricade boundary. In each case, plutonium resuspension was shown by increased airborne plutonium concentrations as a function of either wind speed or as compared to fallout levels. All measured airborne concentrations were far below maximum permissible concentrations (MPC). Both plutonium and cesium concentrations on airborne soil were normalized by the quantity of airborne soil sampled. Airborne radionuclide concentrations in μCi/g were related to published values for radionuclide concentrations on surface soils. For this ratio of radionuclide concentration per gram on airborne soil divided by that for ground surface soil, there are eight orders of magnitude uncertainty from 10 -4 to 10 4 . This uncertainty in the equality between plutonium concentrations per gram on airborne and surface soils is caused by only a fraction of the collected airborne soil being transported from offsite rather than all being resuspended from each study site and also by the great variabilities in surface contamination. Horizontal plutonium fluxes on airborne nonrespirable soils at all three sites were bracketed within the same four orders of magnitude from 10 -7 to 10 -3 μCi/(m 2 day) for 239 Pu and 10 -8 to 10 -5 μCi/(m 2 day) for 238 Pu. Airborne respirable 239 Pu concentrations increased with wind speed for a southwest wind direction coming from offsite near the Hanford reservation Prosser barricade. Airborne plutonium fluxes on nonrespirable particles had isotopic ratios, 240 Pu/ 239 240 Pu, similar to weapons grade plutonium rather than fallout plutonium

  15. 3D Modelling of Transport, Deposition and Resuspension of Highway Deposited Sediments in wet Detention Ponds

    DEFF Research Database (Denmark)

    Bentzen, Thomas Ruby

    2010-01-01

    concrete channel with width of 0.8m and a water depth of approximately 0.8m and in circular flume experiments in order to reproduce near-bed specific processes such as resuspension and consolidation. With a fairly good agreement with measurements, modelling of hydrodynamics, transport of dissolved...... pollutants and particles in wet detention ponds is possible with application of a three dimensional RANS model and the advection/dispersion equation taken physical phenomena like wind, waves, deposition, erosion and consolidation of the bottom sediment into account....

  16. Long-term moderate wind induced sediment resuspension meeting phosphorus demand of phytoplankton in the large shallow eutrophic Lake Taihu.

    Directory of Open Access Journals (Sweden)

    Jian-Ying Chao

    Full Text Available The objective of this study was to investigate the impact of sediment resuspension and phosphorus (P release on phytoplankton growth under different kinds of wind-wave disturbance conditions in the large and shallow eutrophic Lake Taihu in China. Short-term strong wind (STSW conditions, long-term moderate wind (LTMW conditions, and static/calm conditions were investigated. To address this objective, we (1 monitored changes in surface water P composition during field-based sediment resuspension caused by STSW conditions in Lake Taihu, and also conducted (2 a series of laboratory-based sediment resuspension experiments to simulate LTMW and calm conditions. The results showed that under both strong and moderate wind-wave conditions, suspended solids (SS and total phosphorus (TP in the water column increased significantly, but total dissolved phosphorus (TDP and soluble reactive phosphorus (SRP remained low throughout the experiments, indicating that the P released from sediments mainly existed in particulate forms. In STSW conditions, alkaline phosphatase activity (APA and enzymatically hydrolysable phosphorus (EHP increased rapidly, with the peak value occurring following the peak value of wind speed for 1-2 days, and then rapidly decreased after the wind stopped. Under LTMW conditions, APA and EHP increased steadily, and by the end of the laboratory experiments, APA increased by 11 times and EHP increased by 5 times. Chlorophyll a (Chl-a in LTMW conditions increased significantly, but remained low under STSW conditions, demonstrating that the former type of sediment P release promoted phytoplankton growth more effectively, and the latter type did not. Despite the fact that STSW conditions resulted in the release of more TP, TP settled to the bottom rapidly with SS after the wind stopped, and did not promote algal growth. Under LTMW conditions, suspended particulate P was hydrolyzed to SRP by phosphatase and promoted algae growth. Algal growth in

  17. Plutonium concentrations in airborne soil at Rocky Flats and Hanford determined during resuspension experiments

    Energy Technology Data Exchange (ETDEWEB)

    Sehmel, G.A.

    1978-01-01

    Plutonium resuspension results are summarized for experiments conducted by the author at Rocky Flats, onsite on the Hanford reservation, and for winds blowing from offsite onto the Hanford reservation near the Prosser barricade boundary. In each case, plutonium resuspension was shown by increased airborne plutonium concentrations as a function of either wind speed or as compared to fallout levels. All measured airborne concentrations were far below maximum permissible concentrations (MPC). Both plutonium and cesium concentrations on airborne soil were normalized by the quantity of airborne soil sampled. Airborne radionuclide concentrations in ..mu..Ci/g were related to published values for radionuclide concentrations on surface soils. For this ratio of radionuclide concentration per gram on airborne soil divided by that for ground surface soil, there are eight orders of magnitude uncertainty from 10/sup -4/ to 10/sup 4/. This uncertainty in the equality between plutonium concentrations per gram on airborne and surface soils is caused by only a fraction of the collected airborne soil being transported from offsite rather than all being resuspended from each study site and also by the great variabilities in surface contamination. Horizontal plutonium fluxes on airborne nonrespirable soils at all three sites were bracketed within the same four orders of magnitude from 10/sup -7/ to 10/sup -3/ ..mu..Ci/(m/sup 2/ day) for /sup 239/Pu and 10/sup -8/ to 10/sup -5/ ..mu..Ci/(m/sup 2/ day) for /sup 238/Pu. Airborne respirable /sup 239/Pu concentrations increased with wind speed for a southwest wind direction coming from offsite near the Hanford reservation Prosser barricade. Airborne plutonium fluxes on nonrespirable particles had isotopic ratios, /sup 240/Pu//sup 239/ /sup 240/Pu, similar to weapons grade plutonium rather than fallout plutonium.

  18. Effects of resuspension on benthic fluxes of oxygen, nutrients, dissolved inorganic carbon, iron and manganese in the Gulf of Finland, Baltic Sea

    NARCIS (Netherlands)

    Almroth, E.; Tengberg, A.; Andersson, J.H.; Pakhomova, S.; Hall, P.O.J.

    2009-01-01

    The effect of resuspension on benthic fluxes of oxygen (O2), ammonium (NH4+), nitrate (NO3-), phosphate (PO43-), silicate (Si(OH)4), dissolved inorganic carbon (DIC), total dissolved iron (Fe) and total dissolved manganese (Mn) was studied at three different stations in the Gulf of Finland (GoF),

  19. KEY COMPARISON: Final report of EUROMET Project 696: pH determination of a phthalate buffer

    Science.gov (United States)

    Spitzer, Petra; Charlet, Philippe; Eberhard, Ralf; Karpov, Oleg V.; Philippe, Rachel; Rivier, Cedric; Maximov, Igor; Sudmeier, Uwe

    2005-01-01

    The EUROMET project 696, a trilateral comparison between PTB, Germany, LNE, France and VNIIFTRI, Russia was performed in order to demonstrate and document the capability of the participants to measure the pH of a phthalate buffer by the primary measurement procedure for pH. Good agreement of the reported results was observed. The sample was very similar to the one used in the comparison CCQM-K17. PTB acts as pilot laboratory in CCQM-K17 and in EUROMET 696. This comparison allows one to link the results obtained by LNE to the CCQM-K17 key comparison through the degree of equivalence of PTB. On the other hand, the discrepancy between measured pH values at the VNIIFTRI and PTB for the same type of buffer solution decreased, as compared with a bilateral comparison in 1997. Main text. To reach the main text of this paper, click on Final Report. The final report has been peer-reviewed and approved for publication by the CCQM, according to the provisions of the Mutual Recognition Arrangement (MRA).

  20. 3D Numerical Modelling of Transport, Deposition and Resuspension of Highway Deposited Sediments in Wet Detention Ponds

    DEFF Research Database (Denmark)

    Bentzen, Thomas Ruby

    2009-01-01

    concrete channel with width of 0.8 m and a water depth of approximately 0.8 m and in circular flume experiments in order to reproduce near-bed specific processes such as resuspension and consolidation. With good agreement with measurements, modelling of hydrodynamics, transport of dissolved pollutants...... and particles in wet detention ponds is possible with application of a three dimensional RANS model and the advection/dispersion equation taken physical phenomena like wind, waves, deposition, erosion and consolidation of the bottom sediment into account....

  1. Active biomonitoring for assessing effects of metal polluted sediment resuspension on gammarid amphipods during fluvial traffic.

    Science.gov (United States)

    Prygiel, E; Billon, G; François, A; Dumoulin, D; Chaumot, A; Geffard, O; Criquet, J; Prygiel, J

    2016-11-01

    The resuspension of polluted sediments by boat traffic could release substantial amounts of metals to the water column, affecting at the same time their bioavailability. In order to characterize the impact of sediment resuspensions on biota, caged amphipods have been deployed on three different channelized watercourses in Northern France. Firstly, the biological responses of transplanted freshwater gammarid amphipods, Gammarus fossarum, described by trace metal accumulation, feeding and reproduction activities were quite similar for the three water courses despite the differences of metal contamination and navigability. Secondly, the concentrations of metals accumulated in gammarids never exceeded the contamination thresholds previously defined for Co, Cu, Cr and Zn. Values were in the same order of magnitude whatever the studied site despite: (i) large differences noticed in the sediment quality and (ii) some concentrations in the overlying waters exceeding the Environmental Quality Standards (EQS) defined by the Water Framework Directive. Conversely, Pb was highly bioaccumulated with values systematically exceeding the threshold value whatever the site. Therefore, the impact of navigation cannot be proved and the difference between the 3 monitoring periods is rather attributed to environmental variability, probably linked to the seasonality. Moreover, this study also confirms that organisms sampled from a local population in the vicinity of the three studied watercourses could be used as test organisms, leading to similar results than the ones obtained with reference gammarids initially used for developing all the biological responses. This would simplify and then promote the development of studies based on gammarid amphipod, G. fossarum, as bioindicators. Copyright © 2016 Elsevier Ltd. All rights reserved.

  2. Resuspension. Decadal monitoring time series of the anthropogenic radioactivity deposition in Japan

    International Nuclear Information System (INIS)

    Igarashi, Yasuhito; Aoyama, Michio; Hirose, Katsumi; Miyao, Takashi; Nemoto, Kazuhiro; Tomita, Masatoshi; Fujikawa, Takashi

    2003-01-01

    Monthly atmospheric depositions of 90 Sr and 137 Cs have been observed at the Meteorological Research Institute (MRI), Tsukuba, Japan. This study reports temporal trends and levels of 90 Sr and 137 Cs depositions in the 1990s. Although the current 90 Sr and 137 Cs concentrations declined dramatically, they have been found continuously in the deposition samples throughout the 1990s. During this period, the annual 90 Sr ( 137 Cs) deposits at MRI ranged from 70-180 (140-350) mBq/m 2 /year. With a sufficiently long time series, the decreasing trend of the deposition evidently differs from the past stratospheric fallout; it is far slower. Thus, reservoirs other than the stratosphere provide small amounts of 90 Sr and 137 Cs to the atmosphere. A simple calculation clearly refutes the significance of the ocean as a potential source of airborne anthropogenic radioactivity. We will demonstrate that these radionuclides in the deposited materials originate from resuspension processes (soil dust suspension processes). The temporal trends of the time series monitoring reveal differences from those in the United Nations Scientific Committee on the Effects of Atomic Radiation (UNSCEAR) Report 2000, which were predicted by a model that disregarded resuspension. The specific activity of 90 Sr ( 137 Cs) in the annual depositions exhibited a 10-year (20-year) half-life. Those data were comparable with values reported in the literature for the half-residence time (HRT) of 90 Sr and 137 Cs in Japanese surface soils. They were also comparable to those calculated from nationwide data of 90 Sr and 137 Cs concentrations in the surface soil (0-10 cm) obtained from the Ministry of Education, Culture, Sports, Science and Technology Environmental Radiation Database (the MEXT Database). Regarding the activity ratio of 137 Cs/ 90 Sr, the Japanese nationwide surface soil data collected during the 1990s in the MEXT Database (median: 5.3, n=584) did not accord with that in the deposition samples

  3. Final report on the key comparison CCPR-K5: Spectral diffuse reflectance

    Science.gov (United States)

    Nadal, Maria; Eckerle, Kenneth L.; Early, Edward A.; Ohno, Yoshi

    2013-01-01

    shows overall good agreement among all participants. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCPR, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

  4. Plutonium: resuspension of aerosols in nuclear installations: bibliographic survey; Le plutonium: mise en suspension d'aerosols dans les installations nucleaires: synthese bibliographique

    Energy Technology Data Exchange (ETDEWEB)

    Guetat, Ph; Monfort, M; Armand, P [CEA Bruyeres-le-Chatel, Dept. Analyse Surveillance Environnement, Service Radioanalyse Chimie Environnement, 91 (France); Alloul-Marmor, L [Societe APTUS, 78 - Versailles (France)

    2006-07-01

    This document presents an analysis and a bibliographical synthesis of the studies on resuspension factors for plutonium. It aims at helping the engineers of safety to specify the scenarios of accidents which relate to their activities and to bring elements justified for the definition of their term-source 'installation' in the safety reports of the installations. (authors)

  5. Waste sludge resuspension and transfer: development program

    International Nuclear Information System (INIS)

    Weeren, H.O.; Mackey, T.S.

    1980-02-01

    The six Gunite waste tanks at Oak Ridge National Laboratory (ORNL) contain about 400,000 gal of sludge that has precipitated from solution and settled during the 35 years these tanks have been in service. Eventual decommissioning of the tanks has been proposed. The first part of this program is to resuspend the accumulated sludge, to transfer it to new storage tanks in Melton Valley, and to dispose of it by the shale-fracturing process. On the basis of preliminary information, a tentative operational concept was adopted. The sludge in each tank would be resuspended by hydraulic sluicing and pumped from the tank. This resuspended sludge would be treated as necessary to keep the particles in suspension and would be pumped to the new waste-storage tanks. Subsequently the sludge would be pumped from the tanks, combined with a cement-base mix, and disposed of by the shale-fracturing facility. Verification of the feasibility of this concept required development effort on characterization of the sludge and development of techniques for resuspending the sludge and for keeping it in suspension. These development efforts are described in this report. Sections of the report describe both the known properties of the sludge and the tests of grinding methods investigated, discuss tests of various suspenders, describe tests with cement-base mixes, summarize hot-cell tests on actual sludge samples, and describe tests that were made at a mockup of a Gunite tank installation. On the basis of the tests made, it was concluded that reslurrying and resuspension of the sludge is quite feasible and that the suspensions can be made compatible with cement mixes

  6. Final report on international comparison CCQM-K83: Halocarbons in dry whole air

    Science.gov (United States)

    Rhoderick, George; Guenther, Franklin; Duewer, David; Lee, Jeongsoon; Moon, Dongmin; Lee, Jinbok; Lim, Jeongsik; Seog Kim, Jin

    2014-01-01

    The growing awareness of climate change/global warming and continuing concerns regarding stratospheric ozone depletion will require future measurements and standards for many compounds, in particular halocarbons that are linked to these issues. In order to track and control the emissions of these species globally in the atmosphere, it is necessary to demonstrate measurement equivalence at the highest levels of accuracy for assigned values of standards. This report describes the results of a key comparison for several of the more important halocarbons at atmospheric concentration levels. The comparison includes the chlorofluorocarbons (CFCs) dichlorodifluoromethane (CFC 12), trichlorofluoromethane (CFC 11), and 1,1,2 trichlorotrifluoroethane (CFC 113); the hydrochlorofluorocarbons (HCFCs) chlorodifluoromethane (HCFC 22) and 1-chloro-1,1-difluoroethane (HCFC 142b); and the hydrofluorocarbon (HFC) 1,1,1,2 tetrafluoroethane (HFC 134a), all in a dried whole air sample. The objective of this key comparison is to compare the measurement capabilities of the participants for these halocarbons at trace atmospheric levels. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

  7. KEY COMPARISON: Final report on bilateral comparison CCEM.RF-K9.1: Thermal noise standards at 12.4 GHz, 13.5 GHz, 15 GHz and 17.5 GHz

    Science.gov (United States)

    Allal, Djamel

    2009-01-01

    A bilateral comparison subsequent to key comparison CCEM.RF-K9 was decided between VNIIFTRI and PTB. It was registered into the BIPM KCDB under the identifier CCEM.RF-K9.1. The results of this comparison were gathered by the pilot laboratory of comparison CCEM.RF-K9, the LNE, and a very good agreement was found between the two participants. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

  8. Plutonium: resuspension of aerosols in nuclear installations: bibliographic survey; Le plutonium: mise en suspension d'aerosols dans les installations nucleaires: synthese bibliographique

    Energy Technology Data Exchange (ETDEWEB)

    Guetat, Ph.; Monfort, M.; Armand, P. [CEA Bruyeres-le-Chatel, Dept. Analyse Surveillance Environnement, Service Radioanalyse Chimie Environnement, 91 (France); Alloul-Marmor, L. [Societe APTUS, 78 - Versailles (France)

    2006-07-01

    This document presents an analysis and a bibliographical synthesis of the studies on resuspension factors for plutonium. It aims at helping the engineers of safety to specify the scenarios of accidents which relate to their activities and to bring elements justified for the definition of their term-source 'installation' in the safety reports of the installations. (authors)

  9. Technical note: Mineralogical, chemical, morphological, and optical interrelationships of mineral dust re-suspensions

    Directory of Open Access Journals (Sweden)

    J. P. Engelbrecht

    2016-08-01

    Full Text Available This paper promotes an understanding of the mineralogical, chemical, and physical interrelationships of re-suspended mineral dusts collected as grab samples from global dust sources. Surface soils were collected from arid regions, including the southwestern USA, Mali, Chad, Morocco, Canary Islands, Cabo Verde, Djibouti, Afghanistan, Iraq, Kuwait, Qatar, UAE, Serbia, China, Namibia, Botswana, Australia, and Chile. The  <  38 µm sieved fraction of each sample was re-suspended in a chamber, from which the airborne mineral dust could be extracted, sampled, and analyzed. Instruments integrated into the entrainment facility included two PM10 and two PM2.5 filter samplers, a beta attenuation gauge for the continuous measurement of PM10 and PM2.5 particulate mass fractions, an aerodynamic particle size analyzer, and a three-wavelength (405, 532, 781 nm photoacoustic instrument with integrating reciprocal nephelometer for monitoring absorption and scattering coefficients during the dust re-suspension process. Filter sampling media included Teflon® membrane and quartz fiber filters for chemical analysis and Nuclepore® filters for individual particle analysis by scanning electron microscopy (SEM. The  <  38 µm sieved fractions were also analyzed by X-ray diffraction for their mineral content while the  >  75,  <  125 µm soil fractions were mineralogically assessed by optical microscopy. Presented here are results of the optical measurements, showing the interdependency of single-scattering albedos (SSA at three different wavelengths and mineralogical content of the entrained dust samples. To explain the elevated concentrations of iron (Fe and Fe ∕ Al ratios in the soil re-suspensions, we propose that dust particles are to a large extent composed of nano-sized particles of micas, clays, metal oxides, and ions of potassium (K+, calcium (Ca2+, and sodium (Na+ evenly dispersed as a colloid or adsorbed in amorphous

  10. Resuspension and redistribution of radionuclides during grassland and forest fires in the Chernobyl exclusion zone: part II. Modeling the transport process

    International Nuclear Information System (INIS)

    Yoschenko, V.I.; Kashparov, V.A.; Levchuk, S.E.; Glukhovskiy, A.S.; Khomutinin, Yu.V.; Protsak, V.P.; Lundin, S.M.; Tschiersch, J.

    2006-01-01

    To predict parameters of radionuclide resuspension, transport and deposition during forest and grassland fires, several model modules were developed and adapted. Experimental data of controlled burning of prepared experimental plots in the Chernobyl exclusion zone have been used to evaluate the prognostic power of the models. The predicted trajectories and elevations of the plume match with those visually observed during the fire experiments in the grassland and forest sites. Experimentally determined parameters could be successfully used for the calculation of the initial plume parameters which provide the tools for the description of various fire scenarios and enable prognostic calculations. In summary, the model predicts a release of some per mille from the radionuclide inventory of the fuel material by the grassland fires. During the forest fire, up to 4% of 137 Cs and 9 Sr and up to 1% of the Pu isotopes can be released from the forest litter according to the model calculations. However, these results depend on the parameters of the fire events. In general, the modeling results are in good accordance with the experimental data. Therefore, the considered models were successfully validated and can be recommended for the assessment of the resuspension and redistribution of radionuclides during grassland and forest fires in contaminated territories

  11. Exposure of inshore corals to suspended sediments due to wave-resuspension and river plumes in the central Great Barrier Reef: A reappraisal

    Science.gov (United States)

    Orpin, Alan R.; Ridd, Peter V.

    2012-09-01

    Suspended sediment in the coastal zone is an important limiting factor for the growth and health of inshore coral reefs. The Great Barrier Reef (GBR) lagoon receives sediment from a number of tropical rivers and the physical and biological effects of riverine discharge and turbidity within the lagoon are of considerable scientific and public interest. Published data from two inshore regions of the GBR are reviewed herein to evaluate the relative influence of river plumes and wave resuspension on suspended sediment concentration (SSC) around coral communities over a range of timescales. Data from Cleveland Bay and from other sites near the mouth of the Tully River show that wave resuspension is the most dominant mechanism controlling SSC at inshore reefs. At many nearshore areas today fine-grained bed sediment is abundant, consistent with millennial-scale geological evidence of sediment dispersal prior to European settlement and catchment impacts. Flocculation, particle settling and dilution occurs within the river plume, and riverine sediment concentrations at reefs directly attributable to individual flood inputs is significantly reduced, suggesting that the plume component is a relatively small contribution to the total suspended sediment mass balance over inter-annual timescales. Resuspension events can generate higher ambient SSC than that measured in flood waters (e.g. Tully River). In addition, while visually spectacular, satellite and aerial images offer limited quantitative information of total sediment load carried by hypopycnal plumes, as many of these plumes may contain algal blooms but relatively low concentrations of suspended sediment (ca. processes common to many continental shelves globally. Despite the examples examined in detail herein, the role of frequency, magnitude and duration in determining the impact or exposure of corals to elevated SSCs is poorly constrained by limited quantitative measurements during events, and our ability to place

  12. Sediment Resuspension and Deposition on Seagrass Leaves Impedes Internal Plant Aeration and Promotes Phytotoxic H2S Intrusion.

    Science.gov (United States)

    Brodersen, Kasper E; Hammer, Kathrine J; Schrameyer, Verena; Floytrup, Anja; Rasheed, Michael A; Ralph, Peter J; Kühl, Michael; Pedersen, Ole

    2017-01-01

    HIGHLIGHTS: Sedimentation of fine sediment particles onto seagrass leaves severely hampers the plants' performance in both light and darkness, due to inadequate internal plant aeration and intrusion of phytotoxic H 2 S. Anthropogenic activities leading to sediment re-suspension can have adverse effects on adjacent seagrass meadows, owing to reduced light availability and the settling of suspended particles onto seagrass leaves potentially impeding gas exchange with the surrounding water. We used microsensors to determine O 2 fluxes and diffusive boundary layer (DBL) thickness on leaves of the seagrass Zostera muelleri with and without fine sediment particles, and combined these laboratory measurements with in situ microsensor measurements of tissue O 2 and H 2 S concentrations. Net photosynthesis rates in leaves with fine sediment particles were down to ~20% of controls without particles, and the compensation photon irradiance increased from a span of 20-53 to 109-145 μmol photons m -2 s -1 . An ~2.5-fold thicker DBL around leaves with fine sediment particles impeded O 2 influx into the leaves during darkness. In situ leaf meristematic O 2 concentrations of plants exposed to fine sediment particles were lower than in control plants and exhibited long time periods of complete meristematic anoxia during night-time. Insufficient internal aeration resulted in H 2 S intrusion into the leaf meristematic tissues when exposed to sediment resuspension even at relatively high night-time water-column O 2 concentrations. Fine sediment particles that settle on seagrass leaves thus negatively affect internal tissue aeration and thereby the plants' resilience against H 2 S intrusion.

  13. Effects of Demersal Otter Trawls on the Re-suspension of Copepod Resting Eggs and its Potential Effects on Recruitment

    DEFF Research Database (Denmark)

    Hansen, Benni Winding; Drillet, Guillaume; Hay, G

    2014-01-01

    Resting eggs are important phases in the life strategy of many coastal and estuarine copepods. The egg mortality in the sediment layers where they are buried, as well as re-suspension from the sediment into the water column where eggs may hatch are factors that affect the success of this life str...... and recruit nauplii to the pelagic, egg viability was reduced by the passage of the gear components. This study also suggests that the viability is dependent on the gear component and accordingly potential effects must be considered for at this level....

  14. The influence of demersal trawl fishing gears on the resuspension of dinoflagellate cysts.

    Science.gov (United States)

    Brown, Lyndsay; Bresnan, Eileen; Summerbell, Keith; O'Neill, Finbarr Gerard

    2013-01-15

    To investigate the influence of towed demersal fishing gears on dinoflagellate cyst resuspension, towing trials with four gear components were carried out at three sites of differing sediment type in the Moray Firth, Scotland. Samples of sediment plumes were collected using plankton nets mounted on a towed sledge. Diversity of resuspended dinoflagellate cysts was similar at all sites and included Protoperidinium and Gonyaulax spp., Proroceratium reticulatum and unidentified 'round brown' cysts. Cyst concentrations per gram of resuspended sediment varied by gear component and sediment particle size distribution. Gear components with lower hydrodynamic drag generated wakes with smaller shear stresses, mobilising fewer larger sand particles, giving larger concentrations of cysts. Muddy sediments contained higher cyst concentrations which declined with increasing grain size. This study has shown that fishing gear and sediment type can influence the redistribution of dinoflagellate cysts and highlights the importance this may have in relation to dinoflagellate blooms. Crown Copyright © 2012. Published by Elsevier Ltd. All rights reserved.

  15. Sediment resuspension events induced by the wake wash of deep-draft vessels

    Science.gov (United States)

    Garel, Erwan; López Fernández, Laura; Collins, Mike

    2008-08-01

    Hydrodynamics and sediment resuspension events, induced at the shoreline by a deep-draft vessel passing nearby, are described. Measurements (pressure, currents and turbidity) were obtained at 4 Hz, on a lower beach ~50 m from a channel where large car ferries operate in Wootton Creek, Isle of Wight. The study focuses on a representative 8-min 32-s-long record, during which two large vessels passed the channel section. At the shore, the passage of each vessel induced a long-period water-level drawdown, followed by a water-level oscillation (seiche) of similar period, and the short-period waves of the wake. Both drawdowns were the main constituents of the prevailing wave pattern. The second drawdown was the largest in amplitude, in response to a higher speed of the ferry, and the influence of the seiche which had been activated during the preceding event. Two successive peaks of turbidity were observed shortly after this drawdown. Analyses of current velocity and direction indicate that the sediments resuspended originated from the shallower upper beach. Anthropogenically induced erosion of the foreshore is predicted at Wootton Creek.

  16. Final report on EUROMET key comparison EUROMET.M.D-K2 (EUROMET 627) "Comparison of density determinations of liquid samples"

    Science.gov (United States)

    Bettin, Horst; Heinonen, Martti; Gosset, André; Zelenka, Zoltán; Lorefice, Salvatore; Hellerud, Kristen; Durlik, Hanna; Jordaan, Werner; Field, Ireen

    2016-01-01

    The results of the key comparison EUROMET 627 (EUROMET.M.D-K2) are presented. This project covered the density measurements of three liquids: dodecane, water and an oil of high viscosity measured at 15 °C, 20 °C and 40 °C. Seven European metrology laboratories and the South African laboratory CSIR-NML (now: NMISA) measured the densities at atmospheric pressure by hydrostatic weighing of solid density standards between 04 October 2001 and 18 December 2001. The stability and homogeneity of the liquids were investigated by the pilot laboratory PTB. The results generally show good agreement among the participants. Only for the simple Mohr-Westphal balances do the uncertainties seem to be underestimated by the laboratories. Furthermore, the measurement of high-viscosity oil was difficult for some laboratories. Nevertheless, the five laboratories PTB/DE, BNM/FR (now: LNE/FR), OMH/HU (now: MKEH/HU), IMGC/IT (now: INRIM/IT) and GUM/PL agree with each other for stated uncertainties of 0.05 kg/m3 or less. This satisfies the current needs of customers who wish to calibrate or check liquid density measuring instruments such as oscillation-type density meters. No reference values were calculated since the subsequent CCM key comparison CCM.D-K2 had a different scope and the EUROMET 627 comparison was soon superseded by the EURAMET 1019 (EURAMET.M.D-K2) comparison. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

  17. Long-term behaviour of plutonium in air and deposition and the role of resuspension in a semi-rural environment in Germany

    Energy Technology Data Exchange (ETDEWEB)

    Rosner, G.; Hoetzl, H.; Winkler, R. [GSF-National Research Center for Environment and Health, Institute of Radiation Protection, Neuherberg (Germany)

    1997-03-05

    Despite a long while since the last surface nuclear weapons test (China, 1980), and since the Chernobyl accident (1986), very small concentrations of plutonium in air and deposition are still observable. The present paper reports and discusses results from our sampling site at Munich-Neuherberg from 1970 to the end of 1991, emphasizing the period since 1985. The methods of sample collection, preparation and radiochemical plutonium analysis are indicated in brief. To obtain Pu values above the detection limit, after 1985 our regular monthly samples were combined to yearly ones, except during the Chernobyl period. The annual mean values of {sup 239+240}Pu air concentration (e.g. 6-2 nBq m{sup -3} between 1987 and 1991) and annual sums of total deposition (e.g. 9-2 mBq m{sup -2} between 1987 and 1991) are reported as well as the Pu specific activities in the top soil layers (0-1, 1-2, 2-5 cm) in 1987 and 1993. The temporal variation of these quantities and the role of resuspension in interpreting the presently observed Pu concentrations are discussed. A practically constant resuspension factor K, 1.20{+-}0.05{center_dot}10{sup -9} m{sup -1}, is obtained for {sup 239+240}Pu from 1989 through 1991, provided the decrease of Pu in the top 0-1 cm soil layer is taken into account.

  18. Long-term behaviour of plutonium in air and deposition and the role of resuspension in a semi-rural environment in Germany

    International Nuclear Information System (INIS)

    Rosner, G.; Hoetzl, H.; Winkler, R.

    1997-01-01

    Despite a long while since the last surface nuclear weapons test (China, 1980), and since the Chernobyl accident (1986), very small concentrations of plutonium in air and deposition are still observable. The present paper reports and discusses results from our sampling site at Munich-Neuherberg from 1970 to the end of 1991, emphasizing the period since 1985. The methods of sample collection, preparation and radiochemical plutonium analysis are indicated in brief. To obtain Pu values above the detection limit, after 1985 our regular monthly samples were combined to yearly ones, except during the Chernobyl period. The annual mean values of 239+240 Pu air concentration (e.g. 6-2 nBq m -3 between 1987 and 1991) and annual sums of total deposition (e.g. 9-2 mBq m -2 between 1987 and 1991) are reported as well as the Pu specific activities in the top soil layers (0-1, 1-2, 2-5 cm) in 1987 and 1993. The temporal variation of these quantities and the role of resuspension in interpreting the presently observed Pu concentrations are discussed. A practically constant resuspension factor K, 1.20±0.05·10 -9 m -1 , is obtained for 239+240 Pu from 1989 through 1991, provided the decrease of Pu in the top 0-1 cm soil layer is taken into account

  19. Sediment Resuspension and Deposition on Seagrass Leaves Impedes Internal Plant Aeration and Promotes Phytotoxic H2S Intrusion

    Directory of Open Access Journals (Sweden)

    Kasper E. Brodersen

    2017-05-01

    Full Text Available HIGHLIGHTS:Sedimentation of fine sediment particles onto seagrass leaves severely hampers the plants' performance in both light and darkness, due to inadequate internal plant aeration and intrusion of phytotoxic H2S.Anthropogenic activities leading to sediment re-suspension can have adverse effects on adjacent seagrass meadows, owing to reduced light availability and the settling of suspended particles onto seagrass leaves potentially impeding gas exchange with the surrounding water. We used microsensors to determine O2 fluxes and diffusive boundary layer (DBL thickness on leaves of the seagrass Zostera muelleri with and without fine sediment particles, and combined these laboratory measurements with in situ microsensor measurements of tissue O2 and H2S concentrations. Net photosynthesis rates in leaves with fine sediment particles were down to ~20% of controls without particles, and the compensation photon irradiance increased from a span of 20–53 to 109–145 μmol photons m−2 s−1. An ~2.5-fold thicker DBL around leaves with fine sediment particles impeded O2 influx into the leaves during darkness. In situ leaf meristematic O2 concentrations of plants exposed to fine sediment particles were lower than in control plants and exhibited long time periods of complete meristematic anoxia during night-time. Insufficient internal aeration resulted in H2S intrusion into the leaf meristematic tissues when exposed to sediment resuspension even at relatively high night-time water-column O2 concentrations. Fine sediment particles that settle on seagrass leaves thus negatively affect internal tissue aeration and thereby the plants' resilience against H2S intrusion.

  20. Modelling of resuspension, seasonality and losses during food processing. First report of the VAMP terrestrial working group

    International Nuclear Information System (INIS)

    1992-05-01

    This is the first report of the Terrestrial Working Group of the Coordinated Research Programme. ''The validation of models for the transfer of radionuclides in terrestrial, urban and aquatic environments and the acquisition of data for that purpose''. The programme seeks to use information on the environmental behaviour of radionuclides available after the Chernobyl accident to test the reliability of assessment models. The models themselves are useful for assessing the radiological impact of all parts of the nuclear fuel cycle. This report contains reviews of three topics: resuspension of radioactive particles; removal of radionuclides during food processing; and seasonality of radioactive contamination of food. The three reviews have been indexed separately. Refs, figs and tabs

  1. Final report on SIM.T-S2: Comparison of the calibration of 100 Ω platinum resistance thermometers

    Science.gov (United States)

    del Campo, D.; Chimenti Ruiz, V.; Méndez-Lango, E.; Córdova, L.; von Borries, E.; Sánchez, C. A.; Arévalo, A.; Aguilera, B.; Guillén, E.; Cabrera, C.; Quintana, L.

    2013-01-01

    An International Comparison on industrial platinum resistance thermometers (PRTs) among the National Metrology Institutes (NMIs) of Spain, Mexico and the Andean Countries (Bolivia, Colombia, Ecuador, Peru and Venezuela) began in 2004 and was successfully completed in 2005. Two PRTs were circulated (hand-carried) and compared from -40 °C up to 250 °C. The Centro Español de Metrología (Spanish NMI), CEM, was the pilot laboratory and the Centro Nacional de Metrología (Mexican NMI), CENAM, was the co-pilot laboratory. This report presents the results of this comparison and provides detailed information of the measurements performed by the participating laboratories. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by SIM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

  2. Sequential resuspension of biofilm components (viruses, prokaryotes and protists) as measured by erodimetry experiments in the Brouage mudflat (French Atlantic coast)

    Science.gov (United States)

    Dupuy, Christine; Mallet, Clarisse; Guizien, Katell; Montanié, Hélène; Bréret, Martine; Mornet, Françoise; Fontaine, Camille; Nérot, Caroline; Orvain, Francis

    2014-09-01

    Resuspension thresholds in terms of friction velocity were experimentally quantified for the prokaryotes, protists and for the first time, viruses of intertidal mudflat biofilms. Differences in resuspension thresholds could be related to the type, behaviour and size of microorganisms and their association with particles. Free microorganisms (viruses, bacteria and some nanoflagellates) were resuspended by weak flow at friction velocities lower than 2 cm s- 1. Chlorophyll a, some nanoflagellates and attached bacteria were resuspended together with the bed's muddy sediment, which required friction velocities larger than 3 cm s- 1. Diatoms smaller than 60 μm were resuspended at velocities between 3 and 5 cm s- 1, while those larger than 60 μm were resuspended at higher friction velocities (5.5 to 6.5 cm s- 1). The thresholds of resuspension also depended on the micro-scale position of microorganisms in the sediment (horizontal and vertical distributions). In the field, the vertical distribution of chlorophyll a (a proxy of microphytobenthos) was skewed, with a maximum in the first 2 mm of sediment. Along the neap-spring tidal cycle, chlorophyll a revealed an increase in MPB biomass in the first 2 mm of the sediment, in relation to light increases with exposure durations. The horizontal distribution of chlorophyll a could be inferred from erosion experiments. During the initial phase of biofilm growth, the distribution of chlorophyll a seemed horizontally homogeneous, and was uniformly eroded at the beginning of the increase in chlorophyll a. From these results, we can make a hypothesis: in the subsequent phase of biofilm growth until the maximum of emersion duration, the eroded quantity of chlorophyll a was larger than expected based from chlorophyll a vertical distribution, suggesting that biofilm horizontal distribution became patchy and enriched chlorophyll a was preferentially eroded. When emersion duration and biofilm growth decreased, the trend was reversed

  3. Final report on SIM Regional Key Comparison SIM.L-K1.2007: Calibration of gauge blocks by optical interferometry

    Science.gov (United States)

    Colín, C.; Viliesid, M.; Chaudhary, K. P.; Decker, J.; Dvorácek, F.; Franca, R.; Ilieff, S.; Rodríguez, J.; Stoup, J.

    2012-01-01

    This Key Comparison of gauge blocks (GB) calibration by optical interferometry was carried out to support this Calibration and Measurement Capability (CMC) of the National Measurement Institutes (NMI) from the SIM Region for this specific service and for those that rely on this kind of technique as required by the Mutual Recognition Arrangement (MRA). It provides evidence of the participant's technical competence and supports the uncertainties they state in their CMC. It is a Regional Key Comparison and should be linked to the upper level corresponding comparison CCL-K1. The comparison had nine participants, five from the SIM Region—NRC-CNRC, Canada; NIST, USA; CENAM, Mexico; INMETRO, Brazil; and INTI, Argentina— and four from other regions—CMI, Czech Rep.; CEM, Spain; NPLI, India; and NMISA South Africa. It included the circulation of fourteen GB—seven steel GB and seven ceramic GB. The circulation of the artifacts started on 2007-11-01 and ended on 2010-04-25. Some additional time was required to publish the results as the same artifacts were used thereafter for comparison SIM.L-S6, Calibration of GB by mechanical comparison, and the results could not be disclosed until the participants of the second circulation loop had sent their results. The final report of this comparison was sent out for review in May 2012 and the final version was approved in August 2012. The behavior of the artifacts throughout the circulation was good and therefore the results obtained were judged technically valid. The reference value was taken as arithmetic mean of the largest subset of consistent results. Most of participates obtained results in good agreement with the reference values with a few exceptions mentioned in the report. The corresponding NMIs are responsible for identifying the causes and taking corrective action. This makes the present comparison exercise valid to support the CMC claims of the participants in GB calibration by optical interferometry. Main text. To

  4. Wind-enhanced resuspension in the shallow waters of South San Francisco Bay: Mechanisms and potential implications for cohesive sediment transport

    Science.gov (United States)

    Brand, Andreas; Lacy, Jessica R.; Hsu, Kevin; Hoover, Daniel; Gladding, Steve; Stacey, Mark T.

    2010-01-01

    We investigated the driving forces of sediment dynamics at the shoals in South San Francisco Bay. Two stations were deployed along a line perpendicular to a 14 m deep channel, 1000 and 2000 m from the middle of the channel. Station depths were 2.59 and 2.19 m below mean lower low water, respectively. We used acoustic Doppler velocimeters for the simultaneous determination of current velocities, turbulence, sediment concentration and fluxes. Maximum current shear velocities were 0.015 m s−1 at the station further from the channel (closer to the shore) and 0.02 m s−1 at the station closer to the channel. Peak wave-induced shear velocities exceeded 0.015 m s−1 at both stations. Maximum sediment concentrations were around 30 g m−3 during calm periods (root mean square wave height −3 and sediment fluxes were 5 times higher than in calm conditions (0.02 g m−2 s−1 versus >0.10 g m−2 s−1) at the station further from the channel 0.36 m above the bed. Closer to the channel, sediment concentrations and vertical fluxes due to wind wave resuspension were persistently lower (maximum concentrations around 50 g m−3 and maximum fluxes around 0.04 g m−2 s−1). Most resuspension events occurred during flood tides that followed wave events during low water. Although wave motions are able to resuspend sediment into the wave boundary layer at low tide, the observed large increases in sediment fluxes are due to the nonlinear interaction of wind waves and the tidal currents.

  5. Sediment Resuspension and Transport During Bora in the Western Adriatic Coastal Current

    Science.gov (United States)

    Mullenbach, B. L.; Geyer, W. R.; Sherwood, C. R.

    2004-12-01

    The Western Adriatic Coastal Current (WACC) is an important agent for along-shelf transport of sediment and fresh water in the western Adriatic Sea. The WACC is driven by a combination of buoyancy forcing from the Po River (northern Adriatic) and wind forcing from northeasterly Bora winds. The large seasonal pulse of freshwater (during the winter) from the Po River influences WACC strength; however, preliminary results from current measurements and model runs indicate that the WACC responds quickly and strongly to Bora wind events, with a strengthening of the current moving southward. Along-margin sediment transport to the south is significantly increased as a result of Bora wind events, presumably because of enhanced wave resuspension and WACC velocity. Elevated sediment fluxes have been observed in both the upper water column (i.e., core of the WACC) and bottom boundary layer (BBL) during these events, which suggests that wind-driven currents may be coupled with the near-bottom transport. This study addresses the interaction of the WACC with the BBL and the impact of this interaction on sediment transport in the western Adriatic. Two benthic tripods were deployed from November 2002 to June 2003 on an across-shelf transect near the Chienti River (at 10 and 20-m water depth), in the region where WACC begins to intensify (200 km south of Po River). Continuous measurements of suspended sediment concentration and current velocity were recorded in the upper-water column and BBL to document sediment transport events. A time series of sediment fluxes and shear velocities (from currents only, u*c; from waves and currents, u*wc) were calculated from these data. Results show that suspended sediment concentrations near the seabed (few cmab) during Bora wind events are strongly correlated with u*wc, which supports a previous hypothesis that wave resuspension (rather than direct fluvial input) is responsible for much of the suspended sediment available for transport southward

  6. KEY COMPARISONS: Final report: SIM regional comparison of ac-dc voltage transfer difference (SIM.EM.K6a, SIM.EM-K9 and SIM.EM-K11)

    Science.gov (United States)

    Campos, Sara; Filipski, Piotr; Izquierdo, Daniel; Afonso, Edson; Landim, Régis P.; Di Lillo, Lucas; Lipe, Thomas

    2009-01-01

    Three comparisons of ac-dc voltage transfer difference held from January to December 2004 are reported. Six NMIs in the SIM region took part: NRC (Canada), NIST (United States of America), CENAM (Mexico), INTI (Argentina), UTE (Uruguay) and INMETRO (Brazil). The comparisons were proposed to assess the measurement capabilities in ac-dc voltage transfer difference of the NMIs in the SIM region. The test points were selected to link the results with the equivalent CCEM Key Comparisons, through three NMIs participating in both SIM and CCEM key comparisons. Additionally, a SIM.EM-Supplementary comparison was proposed, in support of the SIM NMIs' power/energy meter calibration capabilities. One technical protocol and one travelling standard were used, to economize on time and resources. The report shows the degree of equivalence in the SIM region and also the degree of equivalence with the corresponding CCEM reference value. The results of all participants support the values and uncertainties of the applicable CMC entries for ac-dc voltage transfer difference in the Key Comparison Database held at the BIPM. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

  7. KEY COMPARISON: Final report on APMP.M.P-K6.1 pneumatic key comparison from 20 kPa to 105 kPa in gauge mode

    Science.gov (United States)

    Hung, Chen-Chuan; Jian, Wu; Changpan, Tawat

    2009-01-01

    This report describes the key comparison APMP.M.P-K6.1 among the three national metrology institutes, Center for Measurement Standards-ITRI (CMS-ITRI, Taiwan), SPRING Singapore and National Institute of Metrology (NIMT), in the pressure range from 20 kPa to 105 kPa in gas media and gauge mode executed during the period April 2003 to April 2004. This comparison was conducted by CMS-ITRI and was based on the calibration procedure of APMP pneumatic pressure comparison APMP.M.P-K6. We intended to link to the CCM.P-K6 key comparison through the APMP.M.P-K6 key comparison by using the proposed linkage method in the APMP.M.P-K6 key comparison to determine a linking factor that can transform the quantities measured in the APMP.M.P-K6.1 key comparison. All three participating institutes used pneumatic piston gauges as their pressure standards. The Ruska 2465 gas-operated piston-cylinder assembly TL-1409 used as transfer standard offered by CMS-ITRI was calibrated three times by the pilot institute during the comparison period and showed that it was very stable after evaluation. The comparison was conducted on the basis of cross-float experiments to determine the effective area of transfer standards from the national standards of three institutes. The comparison results (as shown in Table 6) were equivalent to the CCM.P-K6 comparison and the relative bilateral degrees of equivalence between two laboratories were smaller than 39.7 × 10-6 from 20 kPa to 105 kPa. These results showed all participating institutes measuring the same quantity in the whole pressure range lay within their expanded uncertainty with confidence level 95%. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCM, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

  8. KEY COMPARISON: Final report on CCQM-K9.2: Subsequent key comparison on pH determination of phosphate buffer by Harned cell measurements

    Science.gov (United States)

    Spitzer, Petra; Giera, Janine; Fraga, Isabel C.; Tønnes Jakobsen, Pia; Jensen, Hans D.; Hyllested, Peter; Karpov, Oleg; Kutovoy, Viatcheslav; Nakamura, Susumu; Vospelova, Alena; Zvezdina, Valentina

    2008-01-01

    CCQM-K9.2 was performed supplementary to the key comparison CCQM-K9 on the pH determination of a phosphate buffer with nominal pH ~ 6.9 (at 25 °C). The sample composition was very similar in both comparisons. Only the source of the starting material used for sample preparation was different. The comparison was restricted to the use of the primary method for pH (Harned cell measurement) as defined in the IUPAC Recommendations [2]. The measurement temperatures were 15 °C, 25 °C, 37 °C. CCQM-K9.2, CCQM-K.9 and the first supplementary comparison CCQM-K9.1 [5] are activities of the Electrochemical Working Group (EAWG) of the CCQM. All three comparisons were coordinated by the PTB, Germany. The Danish Primary Laboratory (DPL) successfully took part in the CCQM-K9. Meanwhile the primary set-up for pH in Denmark moved from DPL affiliated to Radiometer Medical to DFM, Denmark. The subsequent comparison allows assessing the degree of equivalence for the measurement of pH at DFM after the move. Due to the interest of other laboratories in demonstrating their progress in pH measurements on the primary level the CCQM-K9.2 supplementary comparison was extended to other participants than DFM, namely NMIJ, VNIIFTRI, INMETRO and CMI. The reported quantity for CCQM-K9.2 was not the pH of the sample but the acidity function at zero chloride molality (see chapter 12). To calculate the pH value from the acidity function it is necessary to know the ionic strength of the sample buffer solution, which was undisclosed by the coordinator. With the exception of the Czech Metrology Institute, CMI, good agreement in the determined acidity function is found between the participants. The results reported by DFM and by PTB agree within their measurement uncertainty at all measurement temperatures. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report

  9. Final report on key comparison COOMET.QM-K36 (Project COOMET 540/UA/11) 'Electrolytic Conductivity 0,5 S/m'

    Science.gov (United States)

    Gavrilkin, V.; Prokopenko, L.; Bakovec, N.; Zolotorevich, E.; Suvorov, V.; Ovchinnikov, Yu; Pilishvili, T.; Buleishvili, M.; Zhasanbaeva, B.; Aytzhatova, G.; Ticona, G.; Vyskocil, L.

    2015-01-01

    The COOMET.QM-K36 key comparison 'Electrolytic conductivity: 0.5 S/m' is a comparison in the field of electrolytic conductivity measurements conducted by COOMET and carried out in 2012. It used a solution of KCl in water and the results are connected to those of the CCQM key comparison CCQM-K36.a through common participation of VNIIFTRI (Russia), SMU (Slovakia) and Ukrmetrteststandart (Ukraine). The purpose of this key comparison was to establish the equivalence of measurements of electrolytic conductivity performed at the National Metrology Institutes of COOMET member states for the value of 0.5 S/m. The results can be used to support the CMCs claims over the range of 0.1 S/m to 1.3 S/m. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

  10. Final report on COOMET.AUV.A-S1: Technical report on supplementary comparison 'Comparison of national standards of the sound pressure unit in air through calibration of working reference microphones'

    Science.gov (United States)

    Pozdeeva, Valentina; Chalyy, Vladimir

    2014-01-01

    The supplementary comparison COOMET.AUV.A-S1 for secondary calibration methods using WS1 and WS2 measurement microphones was carried out from 2009 to 2010. The results were submitted to and approved by CCAUV in April 2014. Four National Metrology Institutes took part in this comparison and are as follows: BelGIM (Belarus), VNIIFTRI (Russia), SMU (Slovakia) and DP NDI 'Sistema' (Ukraine). Three of the above NMIs (VNIIFTRI, SMU and DP NDI 'Sistema') had earlier participated in COOMET key comparisons and one NMI (VNIIFTRI) had also participated in CCAUV key comparisons. The Comparison Reference Values were calculated as the weighted mean values from results obtained by three institutes. The comparison results show agreement for all participants in the frequency range from 20 Hz to 12.5 kHz for WS1 microphones, and in the frequency range from 20 Hz to 16 kHz for WS2 microphones. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCAUV, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

  11. Final report on COOMET Vickers PTB/VNIIFTRI key comparison (COOMET.M.H-K1.b and COOMET.M.H-K1.c)

    Science.gov (United States)

    Aslanyan, E.; Herrmann, K.

    2013-01-01

    This report describes a COOMET key comparison on Vickers hardness scales of two National Metrology Institutes—PTB and VNIIFTRI. The pilot laboratory was PTB, which was the linking institute with the key comparison reference values of CCM.H-K1. In the key comparison two sets of hardness reference blocks for the Vickers hardness scales HV1 and HV30, each consisting of three hardness reference blocks with the hardness levels 240 HV, 540 HV and 840 HV, are used. The same hardness reference blocks were used previously in the key comparison CCM.H-K1. The measurement results and uncertainty assessments, announced by VNIIFTRI, are in good agreement with the key comparison reference values of CCM.H-K1. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

  12. Final Comparison Study of Teaching Blended In-Class Courses vs. Teaching Distance Education Courses

    Directory of Open Access Journals (Sweden)

    Susan J. Martin

    2012-12-01

    Full Text Available This paper will share with the members of the conference the findings from the final study. This study contains five semesters of analyzed data which compares the retention of students, final grades for students, grades for five specific tasks that were given in blended in-class courses and in the totally online courses, and a comparison of data by GPA, gender, and by class level. All courses were American Politics PLSC 111. Each semester one or two American Politics courses were conducted in the classroom and one American Politics distance education course was conducted totally online. Each time the courses were given, it was during the same semester and by the same professor who is the researcher.

  13. The variation of particle gas-borne concentration with time in a gas cooled reactor

    International Nuclear Information System (INIS)

    Reed, J.; Hall, D.; Reeks, M.W.

    1985-01-01

    If volatile fission products are released from fuel during a reactor fault, a significant fraction could become attached to small particles also present in the coolant. In such circumstances the retention of those particles by the reactor circuit will limit the level of gas-borne particle concentration and hence be important in reducing the potential release of fission product activity to the atmosphere. Clearly the retention of particles will be influenced by both the deposition and resuspension of particles from surfaces exposed to the coolant flow. In this paper we consider deposition and resuspension but pay particular attention to the role of resuspension, which in the past has been given little consideration. A recently developed model for the resuspension of small particles by a turbulent flow is outlined. Traditionally, resuspension has been interpreted as a force balance between the aerodynamic removal forces and the surface adhesive forces. In contrast, this new approach embodies an energy balance criterion for particle resuspension. Furthermore, the stochastic nature of this new model has shown that resuspension can be sub-divided into two regimes: (i) initial resuspension (resuspension occurring in times less than a second) which reduces the net deposition of particles to a surface; and (ii) longer term resuspension (resuspension after 1 second) which determines the asymptotic decay of particle gas-borne concentration. It is seen that the asymptotic decay varies almost inversely as the decay time. Force balance models are unsuccessful in accounting for the experimentally observed longer term resuspension. We show that a Volterra integro-differential equation best describes the variation of particle gas-borne concentration with time in a recirculating gas flow such as a gas cooled reactor. It is seen that the longer term resuspension has a major influence in the final decay of particle concentration. (author)

  14. The variation of particle gas-borne concentration with time in a gas cooled reactor

    Energy Technology Data Exchange (ETDEWEB)

    Reed, J; Hall, D; Reeks, M W [Central Electricity Generating Board, Berkeley Nuclear Laboratories (United Kingdom)

    1985-07-01

    If volatile fission products are released from fuel during a reactor fault, a significant fraction could become attached to small particles also present in the coolant. In such circumstances the retention of those particles by the reactor circuit will limit the level of gas-borne particle concentration and hence be important in reducing the potential release of fission product activity to the atmosphere. Clearly the retention of particles will be influenced by both the deposition and resuspension of particles from surfaces exposed to the coolant flow. In this paper we consider deposition and resuspension but pay particular attention to the role of resuspension, which in the past has been given little consideration. A recently developed model for the resuspension of small particles by a turbulent flow is outlined. Traditionally, resuspension has been interpreted as a force balance between the aerodynamic removal forces and the surface adhesive forces. In contrast, this new approach embodies an energy balance criterion for particle resuspension. Furthermore, the stochastic nature of this new model has shown that resuspension can be sub-divided into two regimes: (i) initial resuspension (resuspension occurring in times less than a second) which reduces the net deposition of particles to a surface; and (ii) longer term resuspension (resuspension after 1 second) which determines the asymptotic decay of particle gas-borne concentration. It is seen that the asymptotic decay varies almost inversely as the decay time. Force balance models are unsuccessful in accounting for the experimentally observed longer term resuspension. We show that a Volterra integro-differential equation best describes the variation of particle gas-borne concentration with time in a recirculating gas flow such as a gas cooled reactor. It is seen that the longer term resuspension has a major influence in the final decay of particle concentration. (author)

  15. Final report on bilateral comparison EURAMET.M.T-S3: Torque wrenches (10 N m - 1 kN m)

    Science.gov (United States)

    Röske, Dirk; Medina, Nieves

    2011-01-01

    A bilateral comparison from 10 N m up to 1000 N m has been carried out between Physikalisch-Technische Bundesanstalt (PTB) and Centro Español de Metrología (CEM) for reference torque wrenches calibrated according to DKD-R 3-7. The transfer standards have been two reference torque wrenches, 10 N m and 1000 N m respectively, that have been measured between November and December 2010. The results presented here demonstrate the metrological equivalence, within the quoted uncertainties, of both participant laboratories. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by EURAMET, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

  16. Contribution to the study of particle resuspension kinetics during thermal degradation of polymers.

    Science.gov (United States)

    Ouf, F-X; Delcour, S; Azema, N; Coppalle, A; Ferry, L; Gensdarmes, F; Lopez-Cuesta, J-M; Niang, A; Pontreau, S; Yon, J

    2013-04-15

    Experimental results are reported on the resuspension of particles deposited on polymer samples representative of glove boxes used in the nuclear industry, under thermal degradation. A parametric study was carried out on the effects of heat flux, air flow rate, fuel type and particle size distribution. Small-scale experiments were conducted on 10 cm × 10 cm PolyMethyl MethAcrylate (PMMA) and PolyCarbonate (PC) samples covered with aluminium oxide particles with physical geometric diameters of 0.7 and 3.6 μm. It was observed for both polymer (fuel) samples that heat flux has no effect on the airborne release fraction (ARF), whereas particle size is a significant parameter. In the case of the PMMA sample, ARF values for 0.7 and 3.6 μm diameter particles range from 12.2% (± 6.2%) to 2.1% (± 0.6%), respectively, whereas the respective values for the PC sample range from 3.2% (± 0.8%) to 6.9% (± 3.9%). As the particle diameter increases, a significant decrease in particle release is observed for the PMMA sample, whereas an increase is observed for the PC sample. Furthermore, a peak airborne release rate is observed during the first instants of PMMA exposure to thermal stress. An empirical relationship has been proposed between the duration of this peak release and the external heat flux. Copyright © 2013 Elsevier B.V. All rights reserved.

  17. Final report of the accident phenomenology and consequence (APAC) methodology evaluation. Spills Working Group

    Energy Technology Data Exchange (ETDEWEB)

    Brereton, S.; Shinn, J. [Lawrence Livermore National Lab., CA (United States); Hesse, D [Battelle Columbus Labs., OH (United States); Kaninich, D. [Westinghouse Savannah River Co., Aiken, SC (United States); Lazaro, M. [Argonne National Lab., IL (United States); Mubayi, V. [Brookhaven National Lab., Upton, NY (United States)

    1997-08-01

    The Spills Working Group was one of six working groups established under the Accident Phenomenology and Consequence (APAC) methodology evaluation program. The objectives of APAC were to assess methodologies available in the accident phenomenology and consequence analysis area and to evaluate their adequacy for use in preparing DOE facility safety basis documentation, such as Basis for Interim Operation (BIO), Justification for Continued Operation (JCO), Hazard Analysis Documents, and Safety Analysis Reports (SARs). Additional objectives of APAC were to identify development needs and to define standard practices to be followed in the analyses supporting facility safety basis documentation. The Spills Working Group focused on methodologies for estimating four types of spill source terms: liquid chemical spills and evaporation, pressurized liquid/gas releases, solid spills and resuspension/sublimation, and resuspension of particulate matter from liquid spills.

  18. Enhanced particle fluxes and heterotrophic bacterial activities in Gulf of Mexico bottom waters following storm-induced sediment resuspension

    Science.gov (United States)

    Ziervogel, K.; Dike, C.; Asper, V.; Montoya, J.; Battles, J.; D`souza, N.; Passow, U.; Diercks, A.; Esch, M.; Joye, S.; Dewald, C.; Arnosti, C.

    2016-07-01

    Bottom nepheloid layers (BNLs) in the deep sea transport and remobilize considerable amounts of particulate matter, enhancing microbial cycling of organic matter in cold, deep water environments. We measured bacterial abundance, bacterial protein production, and activities of hydrolytic enzymes within and above a BNL that formed in the deep Mississippi Canyon, northern Gulf of Mexico, shortly after Hurricane Isaac had passed over the study area in late August 2012. The BNL was detected via beam attenuation in CTD casts over an area of at least 3.5 km2, extending up to 200 m above the seafloor at a water depth of 1500 m. A large fraction of the suspended matter in the BNL consisted of resuspended sediments, as indicated by high levels of lithogenic material collected in near-bottom sediment traps shortly before the start of our sampling campaign. Observations of suspended particle abundance and sizes throughout the water column, using a combined camera-CTD system (marine snow camera, MSC), revealed the presence of macroaggregates (>1 mm in diameter) within the BNL, indicating resuspension of canyon sediments. A distinct bacterial response to enhanced particle concentrations within the BNL was evident from the observation that the highest enzymatic activities (peptidase, β-glucosidase) and protein production (3H-leucine incorporation) were found within the most particle rich sections of the BNL. To investigate the effects of enhanced particle concentrations on bacterial activities in deep BNLs more directly, we conducted laboratory experiments with roller bottles filled with bottom water and amended with experimentally resuspended sediments from the study area. Macroaggregates formed within 1 day from resuspended sediments; by day 4 of the incubation bacterial cell numbers in treatments with resuspended sediments were more than twice as high as in those lacking sediment suspensions. Cell-specific enzymatic activities were also generally higher in the sediment

  19. Emission, transport, deposition, and re-suspension of radionuclides from Fukushima Dai-ichi Nuclear Power Plant in the atmosphere - Overview of 2-year investigations in Japan

    Science.gov (United States)

    Kita, Kazuyuki; Igarashi, Yasuhiro; Yoshida, Naohiro; Nakajima, Teruyuki

    2013-04-01

    Following a huge earthquake and tsunami in Eastern Japan on 11 March, 2011, the accident in Fukushima Dai-ichi Nuclear Power Plant (FDNPP) occurred to emit a large amount of artificial radionuclides to the environment. Soon after the FDNPP accident, many Japanese researchers, as well as researchers in other countries, started monitoring radionuclides in various environmental fields and/or model calculations to understand extent and magnitude of radioactive pollution. In this presentation, we overview these activities for the atmospheric radionuclides in Japan as followings: 1. Investigations to evaluate radionuclide emissions by explosions at FNDPP in March 2011 and to estimate the respiration dose of the radiation at this stage. 2. Investigations to evaluate atmospheric transport and deposition processes of atmospheric radionuclide to determine the extent of radionuclide pollution. -- Based on results of the regular and urgent monitoring results, as well as the mapping of the distribution of radionuclide s accumulated by the deposition to the ground, restoration of their time-dependent emission rates has been tried, and processes determining atmospheric concentration and deposition to the ground have been investigated by using the model calculations. 3. Monitoring of the atmospheric concentrations of radionuclide after the initial, surge phase of FNDPP accident. 4. Investigations to evaluate re-suspension of radionuclide from the ground, including the soil and the vegetation. -- Intensive monitoring of the atmospheric concentrations and deposition amount of radionuclide after the initial, surge phase of the accident enable us to evaluate emission history from FNDPP, atmospheric transport and deposition processes, chemical and physical characteristics of atmospheric radionuclide especially of radio cesium, and re-suspension processes which has become dominant process to supply radio cesium to the atmosphere recently.

  20. Final report on CCT-K6: Comparison of local realisations of dew-point temperature scales in the range -50 °C to +20 °C

    Science.gov (United States)

    Bell, S.; Stevens, M.; Abe, H.; Benyon, R.; Bosma, R.; Fernicola, V.; Heinonen, M.; Huang, P.; Kitano, H.; Li, Z.; Nielsen, J.; Ochi, N.; Podmurnaya, O. A.; Scace, G.; Smorgon, D.; Vicente, T.; Vinge, A. F.; Wang, L.; Yi, H.

    2015-01-01

    A key comparison in dew-point temperature was carried out among the national standards held by NPL (pilot), NMIJ, INTA, VSL, INRIM, MIKES, NIST, NIM, VNIIFTRI-ESB and NMC. A pair of condensation-principle dew-point hygrometers was circulated and used to compare the local realisations of dew point for participant humidity generators in the range -50 °C to +20 °C. The duration of the comparison was prolonged by numerous problems with the hygrometers, requiring some repairs, and several additional check measurements by the pilot. Despite the problems and the extended timescale, the comparison was effective in providing evidence of equivalence. Agreement with the key comparison reference value was achieved in the majority of cases, and bilateral degrees of equivalence are also reported. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCT, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

  1. Spreading of 137 C in the Goiania urban area by resuspension and transport of surface soil

    International Nuclear Information System (INIS)

    Rio, Monica Pires do; Amaral, Eliana

    2002-01-01

    The resuspension of surface soil was considered the mechanism responsible by the spreading of 137 Cs after the Goiania accident, which affected an urban area of about 1 km 2 . Studies on the transport of 137 Cs associated to the surface soil were performed in a house located at 57 th Street, close to the main focus of contamination, from 05/89 to 07/00. Periodically, samples of surface soil and soil profile were collected at the house yards and street dust sampling at representative locations was performed in order to know the extension of the contamination in the city. The soil profile samples have shown the low mobility of 137 Cs in deep layers of the soil, although a slight long-term decrease of the 137 Cs activity concentration in the surface soil were observed. The 137 Cs activity concentration in the street dust samples also decrease with time, suggesting a natural dilution of the contamination in those samples; higher values were only found in few locations close to the foci of primary deposition and no additional spreading of the radionuclide is expected to occur from that area. Street dust sampling is a suitable method to assess the spreading of caesium in urban environment. (author)

  2. A novel specialized suture and inserting device for the resuspension of ptotic facial tissues: early results.

    Science.gov (United States)

    Bisaccia, Emil; Kadry, Razan; Saap, Liliana; Rogachefsky, Arlene; Scarborough, Dwight

    2009-04-01

    In the past decade, the popularity of minimally invasive procedures for facial rejuvenation has increased. To describe a new specialized suture, and its associated technique, used to elevate sagging tissues of the face and neck. A detailed description of the technique and the results obtained in 20 patients in whom we have used this novel approach. Attention was given to appropriate patient selection. The primary focus was on the correction of the jowl, jawline, and neck subunits. It involves the percutaneous introduction of a novel 3-0 polypropylene suture that has 10 absorbable hollow cones along its axis that are equally interspersed with knots. Once the absorbable cones are resorbed into the surrounding tissues, the non-absorbable suture component can be removed without compromising the aesthetic outcome. All patients demonstrated improvement in these areas, with minimal complications. One patient required resuspension using the open technique. (Excessive ptotic tissue was later excised for an optimal cosmetic result.) The suture and technique described in this article provide a major contribution to the correction of ptosis of facial tissues. When done in conjunction with other procedures, such as neck and jowl microliposuction, this technique has proven to be a useful addition to facial rejuvenation.

  3. Final comparison report on ISP-35: Nupec hydrogen mixing and distribution test (Test M-7-1)

    International Nuclear Information System (INIS)

    1994-12-01

    This final comparison report summarizes the results of the OECD/CSNI sponsored ISP-35 exercise which was based on NUPEC's Hydrogen Mixing and Distribution Test M-7-1. 12 organizations from 10 different countries took part in the exercise. For the ISP-35 test, a steam/light gas (helium) mixture was released into the lower region of a simplified model of a PWR containment. At the same time, the dome cooling spray was also activated. the transient time histories for gas temperature and concentrations were recorded for each of the 25 compartments of the model containment. The wall temperatures as well as the dome pressure were also recorded. The ISP-35 participants simulated the test conditions and attempted to predict the time histories using their accident analysis codes. Results of these analyses are presented, and comparisons are made between the experimental data and the calculated data. In general, predictions for pressure, helium concentration and gas distribution patterns were achieved with acceptable accuracy

  4. SUPPLEMENTARY COMPARISON: Final report on supplementary comparison APMP-T-S3-03 of industrial platinum resistance and liquid in glass thermometers from -40 °C to 250 °C

    Science.gov (United States)

    Norranim, Uthai; Nguyen, Mong Kim; Ballico, Mark J.

    2007-01-01

    Industrial thermometers such as industrial platinum resistance thermometers (iprts) and liquid-in-glass thermometers (LIGTs) are widely used in industry. Because Key Comparisons are limited to direct realizations of ITS-90, and not all APMP NMIs have participated in them, the national metrology institutes (NMIs) of Thailand and Australia (NIMT and NIMA) organized an APMP supplementary comparison to support the approval of CMCs (calibration and measurement capabilities) for these laboratories. The comparison, performed in 2003, covered the range from -40.0 °C to 250.0 °C, using IPRTs (Hart Scientific 5626-12-S), total immersion (ASTM 62C, 120C) and partial immersion (ASTM 40C) LIGTs. Ten NMIs from the APMP: KIM-LIPI (Indonesia), ITDI (Philippines), MSL (New Zealand), NBSM (Nepal), NMIA (Australia), NIMT (Thailand), SCL (Hong Kong), SIRIM (Malaysia), SPRING (Singapore) and VMI (Vietnam) were divided into two loops to shorten the circulation time, and these were linked by the two pilot laboratories. This report describes details of the artifacts, the circulation schedule, the measurement procedures, the results submitted by participants, uncertainties and the analysis of the results. Reference values calculated using simple mean, median and weighted mean were consistent with each other, but as the Birge criterion was satisfied, the weighted mean with its lower uncertainty was adopted. The artifacts were found to be stable over the comparison and the results of the loop linking labs consistent, allowing an uncertainty of 2 mK to 4 mK to be achieved for the IPRT reference value and 10 mK to 20 mK for the LIGT reference values. These uncertainties allowed the comparison data to be used to adequately test the uncertainties of all the participant laboratories, and hence to directly support their CMC claims. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database

  5. Resuspension of soil as a source of airborne lead near industrial facilities and highways.

    Science.gov (United States)

    Young, Thomas M; Heeraman, Deo A; Sirin, Gorkem; Ashbaugh, Lowell L

    2002-06-01

    Geologic materials are an important source of airborne particulate matter less than 10 microm aerodynamic diameter (PM10), but the contribution of contaminated soil to concentrations of Pb and other trace elements in air has not been documented. To examine the potential significance of this mechanism, surface soil samples with a range of bulk soil Pb concentrations were obtained near five industrial facilities and along roadsides and were resuspended in a specially designed laboratory chamber. The concentration of Pb and other trace elements was measured in the bulk soil, in soil size fractions, and in PM10 generated during resuspension of soils and fractions. Average yields of PM10 from dry soils ranged from 0.169 to 0.869 mg of PM10/g of soil. Yields declined approximately linearly with increasing geometric mean particle size of the bulk soil. The resulting PM10 had average Pb concentrations as high as 2283 mg/kg for samples from a secondary Pb smelter. Pb was enriched in PM10 by 5.36-88.7 times as compared with uncontaminated California soils. Total production of PM10 bound Pb from the soil samples varied between 0.012 and 1.2 mg of Pb/kg of bulk soil. During a relatively large erosion event, a contaminated site might contribute approximately 300 ng/m3 of PM10-bound Pb to air. Contribution of soil from contaminated sites to airborne element balances thus deserves consideration when constructing receptor models for source apportionment or attempting to control airborne Pb emissions.

  6. Final report: Bilateral key comparison SIM.T-K6.3 on humidity standards in the dew/frost-point temperature range from -30°C to 20°C

    Science.gov (United States)

    Huang, Peter; Meyer, Christopher; Brionizio, Julio D.

    2015-01-01

    A Regional Metrology Organization (RMO) Key Comparison of dew/frost point temperatures was carried out by the National Institute of Standards and Technology (NIST, USA) and the Instituto Nacional de Metrologia, Qualidade e Tecnologia (INMETRO, Brazil) between October 2009 and March 2010. The results of this comparison are reported here, along with descriptions of the humidity laboratory standards for NIST and INMETRO and the uncertainty budget for these standards. This report also describes the protocol for the comparison and presents the data acquired. The results are analyzed, determining degree of equivalence between the dew/frost-point standards of NIST and INMETRO. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCT, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

  7. Characterization of dust samples from a coal strip mine using a resuspension chamber

    Directory of Open Access Journals (Sweden)

    Martin Civiš

    2017-06-01

    Full Text Available A metallic cylindrical resuspension chamber (V = 0.437 m3, S = 0.35 m2, S/V = 8.38 was constructed to disperse samples of soil and various kinds of dust. The chamber allows on-line determination of number/mass size distribution of aerosol particles formed by dispersion and subsequent sampling of size-segregated particles on filter media. The samples tested were lignite, power plant flue ash and overburden soil from the Nastup coal strip mine in Northern Bohemia. About 20 mg of the individual samples were pneumatically dispersed by 0.5 liter of pressurized air inside the chamber under defined temperature and humidity conditions. Then the dynamics of aerosol size distributions was recorded using an aerodynamic particle sizer with a frequency of 5 seconds. The lignite and flue ash contributed most to the mass of atmospheric aerosol particles smaller than 10/2.5 micrometer – PM10/ PM2.5. The re-suspended mass of the samples varied between 0.001% for overburden soil and 0.32% for mine road soil. The aerosolized lignite and flue ash samples, sampled by a Harvard Impactor and a Personal Cascade Impactor Sampler, revealed that the ash contained higher amounts of fine particles than the lignite and subsequent chemical analyses, carried out using SEM-EDX, reveals that the PM2.5 fraction formed by dispersion of the ash samples had the highest content of sulphur, and PM10 was dominated by Si. PM10 was closest to mullite, while the PM2.5 fraction contained sulphides, pyrites, pyrrhotites and polytypes of sulphide. The PM1 fraction was dominated by quartz glass. The fractions of sizes 2.5–1 μm and 0.5–0.25 μm were dominated by Si and S, respectively.

  8. KEY COMPARISON: Final report on CCEM key comparison CCEM.RF-K10.CL (GT-RF/99-2) 'Power in 50 Ω coaxial lines, frequency: 50 MHz to 26 GHz' measurement techniques and results

    Science.gov (United States)

    Janik, Dieter; Inoue, T.; Michaud, A.

    2006-01-01

    This report summarizes the results and the measuring methods of an international key comparison between twelve national metrology institutes (NMIs) and is concerning the calibration factor of RF power sensors in the coaxial 3.5 mm line for frequencies up to 26 GHz. Two RF power travelling standards fitted with male PC 3.5 mm connectors were measured at seven frequencies. The following NMIs participated: NMIJ (Japan), NRC (Canada), NIST (USA), METAS (Switzerland), CSIR-NML (South Africa), NMIA (Australia), NPL (UK), SiQ (Slovenia), IEN (Italy), VNIIFTRI (Russian Federation), SPRING (Singapore) and PTB (Germany), as the pilot laboratory. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

  9. Final report on APMP.M.H-S3: Comparison on hardness measurement Rockwell scale A and B

    Science.gov (United States)

    Sanponpute, Tassanai; Meesaplak, Apichaya; Menelao, Febo; Chan, T. K.; Bahng, Gun-Woong; Titus, S. S. K.; Jain, S. K.

    2012-01-01

    The APMP.M.H-S3 Rockwell hardness intercomparison was initiated by NIMT, Thailand and the required protocol was prepared by NIMT and checked by Dr John Man, MNIA, Australia, in 2009. PTB, Germany, Standards and Calibration Laboratory (SCL), Hong Kong, National Physical Laboratory (NPLI), India, and Korea Research Institute of Standards and Science (KRISS), Korea, participated in this comparison. This comparison exercise was focused on the measurement range of 25 to 100 HRBW scale and 35 to 85 HRA scale. The round robin test was done during the period from April 2010 to October 2010. The participating laboratories have demonstrated the capability of the machine and the operating conditions according to ISO 6508 Part 3 to perform the measurements. However, SCL, Hong Kong, could demonstrate their capability to perform the measurements only according to ISO 6508 Part 2. The CMCs declared by the different laboratories lie in the range of 0.30 HRA to 0.40 HRA and 0.40 HRBW to 0.75 HRBW. The CMC declared by SCL for the Rockwell B scale is 1.5 HRBW for the reason described above. It is observed from the results that the measurement uncertainty is estimated not less than the CMCs declared by the laboratories. From the measurement results provided by all the participating laboratories, the En ratio was determined to establish the degrees of equivalence. The En ratio was calculated by including as well as by excluding the results of the laboratory which has performed the test according to ISO 6508 Part 2 in order to make sure that it does not affect the overall results. It is noticed that the En ratio was still found to remain less than 1. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the APMP, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

  10. Final report of AFRIMETS.M.M-S6: supplementary comparison of 100 mg, 100 g 500 g, 1 kg and 5 kg stainless steel mass standards

    Science.gov (United States)

    Mautjana, R. T.; Molefe, P. T.; Mayindu, N. F.; Armah, M. N.; Ramasawmy, V.; Albasini, G. L.; Matali, S.; Richmond, H.; Rusimbi, V.; Kiwanuka, J.; Mutale, D. M.; Mutsimba, F.

    2018-01-01

    This report summarizes the results of AFRIMETS.M.M-S6 mass standards comparison conducted between eleven participating laboratories/countries. Two sets of five weights with nominal values 100 mg, 100 g, 500 g, 1 kg and 5 kg were used as the traveling standards. These nominal values were decided from the needs of participating laboratories submitted to the pilot laboratory through a questionnaire and agreed upon by all participants. The traveling standards were hand carried between laboratories starting from February 2014 and were received from the last participants in October 2014. The programme was coordinated by National Metrology Institute of South Africa (NMISA), who provided the travelling standards and reference values for the comparison. The corrections to the BIPM as-maintained mass unit [5] have insignificant influence on the results of this comparison. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

  11. The hadronic final state in the deep inelastic electron-proton scattering. A comparison between the ZEUS data measured 1992 and theoretical models

    International Nuclear Information System (INIS)

    Schneider, J.L.

    1993-12-01

    The hadronic final state in deep inelastic e - P collisions has been studied with the 1992 data from the ZEUS detector at HERA. The hadronic final state is described by event topology variables like thrust and sphericity and also by variables like multiplicity and transverse momentum. These quantities require the reconstruction of the particle four moments which are calculated from calorimeter cell clusters (condensates). A detailed Monte-Carlo comparison between final state particles and condensates is presented. ZEUS data and model predictions are compared in the γ * P system. Good agreement between data and models is found in the x-Feynman and transverse momentum spectra and in the seagull plot. Mean thrust and sphericity are measured as functions of the invariant mass W of the hadronic final state. They significantly deviate from the model predictions, as do the mean multiplicities, which exceed the model predictions by about 1 unit. (orig.)

  12. Crystal accumulation in the Hanford Waste Treatment Plant high level waste melter. Preliminary settling and resuspension testing

    Energy Technology Data Exchange (ETDEWEB)

    Fox, K. M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Fowley, M. D. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Miller, D. H. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2016-05-01

    The full-scale, room-temperature Hanford Tank Waste Treatment and Immobilization Plant (WTP) High-Level Waste (HLW) melter riser test system was successfully operated with silicone oil and magnetite particles at a loading of 0.1 vol %. Design and construction of the system and instrumentation, and the selection and preparation of simulant materials, are briefly reviewed. Three experiments were completed. A prototypic pour rate was maintained, based on the volumetric flow rate. Settling and accumulation of magnetite particles were observed at the bottom of the riser and along the bottom of the throat after each experiment. The height of the accumulated layer at the bottom of the riser, after the first pouring experiment, approximated the expected level given the solids loading of 0.1 vol %. More detailed observations of particle resuspension and settling were made during and after the third pouring experiment. The accumulated layer of particles at the bottom of the riser appeared to be unaffected after a pouring cycle of approximately 15 minutes at the prototypic flow rate. The accumulated layer of particles along the bottom of the throat was somewhat reduced after the same pouring cycle. Review of the time-lapse recording showed that some of the settling particles flow from the riser into the throat. This may result in a thicker than expected settled layer in the throat.

  13. KEY COMPARISON: Final report of APMP.T-K6 (original name APMP-IC-1-97): Comparison of humidity measurements using a dew point meter as a transfer standard

    Science.gov (United States)

    Li, Wang; Takahashi, C.; Hussain, F.; Hong, Yi; Nham, H. S.; Chan, K. H.; Lee, L. T.; Chahine, K.

    2007-01-01

    This APMP key comparison of humidity measurements using a dew point meter as a transfer standard was carried out among eight national metrology institutes from February 1999 to January 2001. The NMC/SPRING, Singapore was the pilot laboratory and a chilled mirror dew point meter offered by NMIJ was used as a transfer standard. The transfer standard was calibrated by each participating institute against local humidity standards in terms of frost and dew point temperature. Each institute selected its frost/dew point temperature calibration points within the range from -70 °C to 20 °C frost/dew point with 5 °C step. The majority of participating institutes measured from -60 °C to 20 °C frost/dew point and a simple mean evaluation was performed in this range. The differences between the institute values and the simple means for all participating institutes are within two standard deviations from the mean values. Bilateral equivalence was analysed in terms of pair difference and single parameter Quantified Demonstrated Equivalence. The results are presented in the report. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCT, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

  14. Sources of present Chernobyl-derived caesium concentrations in surface air and deposition samples

    International Nuclear Information System (INIS)

    Hoetzl, H.; Rosner, G.; Winkler, R.; Gesellschaft fuer Strahlen- und Umweltforschung mbH Muenchen, Neuherberg

    1992-01-01

    The sources of Chernobyl-derived caesium concentrations in air and deposition samples collected from mid-1986 to end-1990 at Munich- Neuherberg, Germany, were investigated. Local resuspension has been found to be the main source. By comparison with deposition data from other locations it is estimated that within a range from 20 Bq m -2 to 60 kBq m -2 of initially deposited 137 Cs activity ∼2% is re-deposited by the process of local resuspension in Austria, Germany, Japan and United Kingdom, while significantly higher total resuspension is to be expected for Denmark and Finland. Stratospheric contribution to present concentrations is shown to be negligible. This is confirmed by cross correlation analysis between the time series of 137 Cs in air and precipitation before and after the Chernobyl accident and the respective time series of cosmogenic 7 Be, which is an indicator of stratospheric input. Seasonal variations of caesium concentrations with maxima in winter were observed. (author). 32 refs.; 5 figs.; 1 tab

  15. Final report on key comparison APMP.M.P-K3: Absolute pressure measurements in gas from 3 × 10-6 Pa to 9 × 10-4 Pa

    Science.gov (United States)

    Yoshida, H.; Arai, K.; Akimichi, H.; Hong, S. S.; Song, H. W.

    2011-01-01

    The results of a key comparison of ultra-high vacuum standards at two national metrology institutes (NMIJ/AIST and KRISS) are reported. This bilateral comparison was carried out from May 2010 to October 2010 within the framework of the Asia-Pacific Metrology Programme (APMP) to determine their degrees of equivalence at pressures in the range from 3 × 10-6 Pa to 9 × 10-4 Pa. The pilot institute was NMIJ/AIST. Two spinning rotor gauges and two hot cathode ionization gauges were used as the transfer standards. NMIJ/AIST used two calibration systems: the dynamic expansion system (NMIJ-DES) and two-stage flow-dividing system (NMIJ-TFS). KRISS used the dynamic expansion system. The transfer standards were sufficiently stable to meet the requirements of the comparison compared with those of previous international comparisons owing to some improvements of the protocol and the transfer standards. The ultra-high vacuum standards of NMIJ/AIST and KRISS were found to be equivalent within their claimed uncertainties in the range from 3 × 10-6 Pa to 9 × 10-5 Pa. The NMIJ-DES results, which have smaller uncertainty than NMIJ-TFS, were transferred to the corresponding CCM key comparison, CCM.P-K3, in the range from 3 × 10-6 Pa to 9 × 10-5 Pa and it is shown that the NMIJ values were equivalent to the CCM key comparison reference value within the claimed uncertainties. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCM, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

  16. KEY COMPARISON: Final report on CCQM-K62: Nutrients in infant/adult formula—Vitamins

    Science.gov (United States)

    Sharpless, Katherine E.; Rimmer, Catherine A.; Phinney, Karen W.; Nelson, Bryant C.; Duewer, David L.; Wise, Stephen A.; Kim, Byungjoo; Liu, Jun; Huang, Ting; Zhang, Wei

    2010-01-01

    and vitamin A and one of the three results for folic acid was withdrawn, no strong conclusions as to the expected comparability of higher-order vitamin measurements can be established. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

  17. Final report on EURAMET.T-K6.1: Bilateral comparison of the realisations of local dew/frost-point temperature scales in the range -70 °C to +20 °C

    Science.gov (United States)

    Heinonen, Martti; Zvizdic, Davor; Sestan, Danijel

    2013-01-01

    As the European extension of the first CCT humidity key comparison, EUROMET.T-K6 was successfully completed in year 2008. After this comparison, a new low dew-point generator was introduced at LPM in Croatia as a result of progress in the EUROMET P912 project. With this new facility, the LPM uncertainties decreased significantly and the operating range became significantly wider. Therefore, it was decided to arrange a bilateral comparison between LPM and MIKES in Finland providing a link to EUROMET.T-K6 and CCT-K6. This comparison was carried out in a manner similar to other K6 comparisons but only one transfer standard was used instead of two units and the measurement point -70 °C was added to the measurement scheme. At all measurement points, the bilateral equivalence was well within the estimated expanded uncertainty at the approximately 95% confidence level. Also, the deviations of the LPM results from the EUROMET.T-K6 reference values were smaller than their expanded uncertainties. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCT, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

  18. Pollutants' Release, Redistribution and Remediation of Black Smelly River Sediment Based on Re-Suspension and Deep Aeration of Sediment.

    Science.gov (United States)

    Zhu, Lin; Li, Xun; Zhang, Chen; Duan, Zengqiang

    2017-04-01

    Heavily polluted sediment is becoming an important part of water pollution, and this situation is particularly acute in developing countries. Sediment has gradually changed from being the pollution adsorbent to the release source and has influenced the water environment and public health. In this study, we evaluated the pollutant distribution in sediment in a heavily polluted river and agitated the sediment in a heavily polluted river to re-suspend it and re-release pollutants. We found that the levels of chemical oxygen demand (COD), NH₄⁺-N, total nitrogen (TN), and total phosphorus (TP) in overlying water were significantly increased 60 min after agitation. The distribution of the pollutants in the sediment present high concentrations of pollutants congregated on top of the sediment after re-settling, and their distribution decreased with depth. Before agitation, the pollutants were randomly distributed throughout the sediment. Secondly, deep sediment aeration equipment (a micro-porous air diffuser) was installed during the process of sedimentation to study the remediation of the sediment by continuous aeration. The results revealed that deep sediment aeration after re-suspension significantly promoted the degradation of the pollutants both in overlying water and sediment, which also reduced the thickness of the sediment from 0.9 m to 0.6 m. Therefore, sediment aeration after suspension was efficient, and is a promising method for sediment remediation applications.

  19. X-ray M4,5 Resonant Raman Scattering from La metal with final 4p hole: Calculations with 4p-4d-4f configuration interaction in the final state and comparison with the experiment

    International Nuclear Information System (INIS)

    Taguchi, M.; Braicovich, L.; Tagliaferri, A.; Dallera, C.; Giarda, K.; Ghiringhelli, G.; Brookes, N.B.; Borgatti, F.

    2001-03-01

    We consider the X-Ray Resonant Raman Scattering (RRS) in La in the whole M 4,5 region ending with a state with a 4p hole, along the sequence 3d 10 4f 0 →3d 9 4f 1 →3d 10 4p 5 4f 1 . The final state configuration mixes with that with two 4d holes i.e. 3d 10 4d 8 4f n+2 having almost the same energy. Thus RRS must be described by introducing final state Configuration Interaction (CI) between states with one 4p hole and with two 4d holes. This approach allows detailed experimental data on La-metal to be interpreted on the basis of a purely ionic approach. It is shown that the inclusion of CI is crucial and has very clear effects. The calculations with the Kramers-Heisenberg formula describe all measured spectral features appearing in the strict Raman regime i.e. dispersing with the incident photon energy. In the experiment also a nondispersive component is present when the excitation energy is greater than about 2 eV above the M 5 peak. The shape and position of this component is well accounted for by a model based on all possible partitions of the excitation energy between localised and extended states. However, the intensity of the nondispersive component is greater in the measurements, suggesting a rearrangement in the intermediate excited state. The comparison of ionic calculations with the metal measurements is legitimate, as shown by the comparison between the measurements on La-metal and on LaF 3 with M 5 excitation, giving the same spectrum within the experimental accuracy. Moreover, the experiment shows that the final lifetime broadening is much greater in the final states corresponding to lower outgoing photon energies than in the states corresponding to higher outgoing photon energies. (author)

  20. SUPPLEMENTARY COMPARISON: COOMET.RI(II)-S1.Rn-222 (169/UA/98): Rn-222 volume activity comparison

    Science.gov (United States)

    Skliarov, V.; Röttger, A.; Honig, A.; Korostin, S.; Kuznetsov, S.; Lapenas, A.; Milevsky, V.; Ivaniukovich, A.; Kharitonov, I.; Sepman, S.

    2009-01-01

    According to a first program, a supplementary comparison of Rn-222 volume activity was drawn up as a bilateral supplementary comparison between NSC 'Institute of Metrology', Ukraine, and VNIIFTRI, Russia. It took place in March 2005. In April 2005, at the 5th meeting of COOMET held in Braunschweig (Germany), representatives of these institutes exchanged data which showed the comparability of the national standards of Ukraine and Russia for the check points. During the discussion of the procedure some other institutes decided to join the comparison program, which was extended to BelGIM (Belarus), PTB (Germany), VNIIM (Russia) and RMTC (Latvia). The national standards of volume activity of radon-222 were thus calibrated using one standard radon radiometer as the transfer standard. Results are shown in the Final Report of the comparison. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by COOMET, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

  1. Sources of present Chernobyl-derived caesium concentrations in surface air and deposition samples

    Energy Technology Data Exchange (ETDEWEB)

    Hoetzl, H.; Rosner, G.; Winkler, R. (Gesellschaft fuer Strahlen-und Umweltforschung Munich, Neuherberg (Germany). Forschungszentrum fuer Umwelt und Gesundheit Gesellschaft fuer Strahlen- und Umweltforschung mbH Muenchen, Neuherberg (Germany). Inst. fuer Strahlenschutz)

    1992-06-01

    The sources of Chernobyl-derived caesium concentrations in air and deposition samples collected from mid-1986 to end-1990 at Munich- Neuherberg, Germany, were investigated. Local resuspension has been found to be the main source. By comparison with deposition data from other locations it is estimated that within a range from 20 Bq m[sup -2] to 60 kBq m[sup -2] of initially deposited [sup 137]Cs activity [approx]2% is re-deposited by the process of local resuspension in Austria, Germany, Japan and United Kingdom, while significantly higher total resuspension is to be expected for Denmark and Finland. Stratospheric contribution to present concentrations is shown to be negligible. This is confirmed by cross correlation analysis between the time series of [sup 137]Cs in air and precipitation before and after the Chernobyl accident and the respective time series of cosmogenic [sup 7]Be, which is an indicator of stratospheric input. Seasonal variations of caesium concentrations with maxima in winter were observed. (author). 32 refs.; 5 figs.; 1 tab.

  2. Final report on COOMET.EM-S11: Supplementary bilateral comparison of the measurement of current transformers between UNIIM and PTB

    Science.gov (United States)

    Mohns, Enrico; Sychev, Y.; Roeissle, G.

    2014-01-01

    A bilateral comparison of the measurement of current transformers was carried out between UNIIM (Russia) and PTB (Germany). For all of the current ratio error measurements and the phase displacement measurements there is a close agreement between PTB and UNIIM. Extensive measurements with the travelling standards were carried out at 18 different current ratios and at 5 different test points (1%, 5%, 20%, 100% and 120%) each. The range of tested primary currents was from 10 mA to 60 kA. It can therefore be concluded that the results of each laboratory agree very well within the calculated measurement uncertainties. No outliers were observed. Considering especially the En factors, the calculated uncertainties seem to be too conservative to some extent. Here there is the possibility to slightly improve the uncertainty budgets in the future if there is a need. The worst En factors are within ±0.6 at 1 kA/5 A and ±0.8 at 3 kA. The current comparator 'IW 32' from PTB may have caused that. This was subsequently confirmed. The primary current induced a small voltage in the compensation winding. This problem has now been solved. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

  3. Lidar Inter-Comparison Exercise Final Campaign Report

    Energy Technology Data Exchange (ETDEWEB)

    Protat, A [Australian Bureau of Meterology; Young, S

    2015-02-01

    The objective of this field campaign was to evaluate the performance of the new Leosphere R-MAN 510 lidar, procured by the Australian Bureau of Meteorology, by testing it against the MicroPulse Lidar (MPL) and Raman lidars, at the Darwin Atmospheric Radiation Measurement (ARM) site. This lidar is an eye-safe (355 nm), turn-key mini Raman lidar, which allows for the detection of aerosols and cloud properties, and the retrieval of particulate extinction profiles. To accomplish this evaluation, the R-MAN 510 lidar has been operated at the Darwin ARM site, next to the MPL, Raman lidar, and Vaisala ceilometer (VCEIL) for three months (from 20 January 2013 to 20 April 2013) in order to collect a sufficient sample size for statistical comparisons.

  4. Final report of the key comparison CCQM-K106: Pb, As and Hg measurements in cosmetic (cream)

    Science.gov (United States)

    Wang, Jun; Wang, Qian; Yamani, Randa Nasr Ahmed; Shehata, Adel B.; Jacimovic, Radojko; Pavlin, Majda; Horvat, Milena; Tsoi, Y. P.; Tsang, C. K.; Shin, Richard; Chailap, Benjamat; Yafa, Charun; Caciano de Sena, Rodrigo; de Almeida, Marcelo; Yim, Yong-Hyeon; Lee, Kyoung-Seok; Heun Kim, Sook; Konopelko, Leonid; Ari, Betül; Tokman, Nilgün; Rienitz, Olaf; Jaehrling, Reinhard; Pape, Carola

    2015-01-01

    relating to CCQM-K106 was sent to each participant by e-mail, which consisted of technical protocol, results report form and inorganic core capabilities tables. The results were reported as mass faction (mg/kg). Calculation of the uncertainty expressed as a combined standard uncertainty and an expanded uncertainty at 95% confidence. In order to allow a sufficient evaluation of the comparison, the report was required to include a detailed description of the applied method of measurement, information about sample digestion and preparation, information about the reference material used for calibration. The methods of measurement were free to be selected by the participants. For the sample treatment, most of the participants used microwave digestion method. For instrumental determination, a variety of techniques such as ICP-MS, AAS, INAA were adopted by the participants. Most participants choose ID-ICP-MS method to measure Pb and Hg, which showed the better performance in terms of consistency and reliability of the measurement results. The reference mass fraction values and associated uncertainties were calculated by different statistic ways. As the result, the median and uncertainty of median were proposed as the key comparison reference value (KCRV) and its associated key comparison reference uncertainty after removal of suspected extreme values. In general, the performances of the majority of the CCQM-K106 participants are excellent, illustrating their measurement capability for Pb, As and Hg in a complex greasy matrix. The results can be used further by any participant to support its CMC claim at least for a borate buffer. That claim will concern the pH method employed by the participant during this comparison and will cover the used temperature(s) or the full temperature range between 15°C and 37 °C for the participant which measured pH values at the three temperatures. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that

  5. SUPPLEMENTARY COMPARISON: EUROMET.L-S10 Comparison of squareness measurements

    Science.gov (United States)

    Mokros, Jiri

    2005-01-01

    from the weighted mean of data from participating laboratories, while some of them were excluded on the basis of statistical evaluation. Graphical interpretations of all deviations are contained in the Final Report. In order to compare the individual deviations mutually (25 profiles for the granite square and 44 profiles for the cylinder), graphical illustrations of 'standard deviations' and both extreme values (max. and min.) of deviations were created. This regional supplementary comparison has provided independent information about the metrological properties of the measuring equipment and method used by the participating NMIs. The Final Report does not contain the En values. Participants could not estimate some contributions in the uncertainty budget on the basis of previous comparisons, since no comparison of this kind had ever been organized. Therefore the En value cannot reflect the actual state of the given NMI. Instead of En, an analysis has been performed by means of the Grubbs test according to ISO 5725-2. This comparison provided information about the state of provision of metrological services in the field of big squares measurement. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by EUROMET, according to the provisions of the Mutual Recognition Arrangement (MRA).

  6. Development of a method for the comparison of final repository sites in different host rock formations; Weiterentwicklung einer Methode zum Vergleich von Endlagerstandorten in unterschiedlichen Wirtsgesteinsformationen

    Energy Technology Data Exchange (ETDEWEB)

    Fischer-Appelt, Klaus; Frieling, Gerd; Kock, Ingo; and others

    2017-10-15

    The report on the development of a method for the comparison of final repository sites in different host rock formations covers the following issues: influence of the requirement of retrievability on the methodology, study on the possible extension of the methodology for repository sites with crystalline host rocks: boundary conditions in Germany, final disposal concept for crystalline host rocks, generic extension of the VerSi method, identification, classification and relevance weighting of safety functions, relevance of the safety functions for the crystalline host rock formation, review of the methodological need for changes for crystalline rock sites under low-permeability covering; study on the applicability of the methodology for the determination of site regions for surface exploitation (phase 1).

  7. Intercomparison of liquid metal fast reactor seismic analysis codes. V. 3: Comparison of observed effects with computer simulated effects on reactor cores from seismic disturbances. Proceedings of a final research co-ordination meeting

    International Nuclear Information System (INIS)

    1996-05-01

    This publication contains the final papers summarizing the validation of the codes on the basis of comparison of observed effects with computer simulated effects on reactor cores from seismic disturbances. Refs, figs tabs

  8. Final repositories for high-level radioactive waste; Endlagerung hochradioaktiver Abfaelle

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2015-10-15

    The brochure on final repositories for high-level radioactive waste covers the following issues: What is the origin of radioactive wastes? How large are the waste amounts? What is going to happen with the wastes? What is the solution for the Waste disposal? A new site search is started. Safety requirements for the final disposal of high-level radioactive wastes. Comparison of host rocks. Who is responsible and who will pay? Final disposal of high-level radioactive wastes worldwide. Short summary: History of the search for a final repository for high-level radioactive wastes in Germany.

  9. Conceptual and safety-related questions in the final storage of radioactive waste - a comparison of various types of host rock

    International Nuclear Information System (INIS)

    Kleemann, U.

    2005-01-01

    The German Federal Office for Radiation Protection (BfS) in early November published the synthesis report (BfS 2005) about the conceptual and safety-related specific questions associated with the final storage of radioactive waste. In addition to a condensed version of twelve individual projects, the report contains a description of the results of the peer review and the workshops carried out, in particular an evaluation comparing different types of host rock in Germany. The whole project constitutes a comprehensive documentation of the current state of the art. Findings are expressed at a general level referring neither to the suitability of any specific repository site nor to that of salts as a repository formation, but covering all potential repository formations in deep geologic strata in Germany. The limits to and possibilities of, generic comparisons of various types of host rock are shown. It si seen that, in principle, none of the host rock varieties in Germany would be preferable to others. Numerous problems can be solved only for specific sites, thus requiring site comparisons. While some questions indicate a need for regulatory treatment, the need for basic research is considered to be low. The contribution presents the main findings made in each of the specific projects and the evaluations by the Office. (orig.)

  10. Biomass Support for the China Renewable Energy Law: Final Report, December 2005

    Energy Technology Data Exchange (ETDEWEB)

    2006-10-01

    Final subcontractor report giving an overview of the biomass power generation technologies used in China. Report covers resources, technologies, foreign technologies and resources for comparison purposes, biomass potential in China, and finally government policies in China that support/hinder development of the using biomass in China for power generation.

  11. Final report on SIM.M.P-S6: Differential pressure comparison from 50 Pa to 500 Pa with a liquid column manometer between CENAM (Mexico) and INTI-Fisica y Metrologia (Argentina)

    Science.gov (United States)

    Torres-Guzman, Jorge; Forastieri, Juan; Zúñiga, Sinuhé

    2011-01-01

    A differential pressure comparison was performed between CENAM (Mexico) and INTI (Argentina) by means of a liquid column manometer. The measuring range was 50 Pa to 500 Pa. CENAM calibrated the transfer standard at the beginning and at the end of the comparison. The transfer standard used was a Dwyer liquid column manometer model Microtector with an accuracy class of 0.013% of the reading. The compared pressure points were (50, 75, 125, 200, 250, 300, 350, 400, 450, 500) Pa. The uncertainty sources to be evaluated included at least the following: (a) uncertainty due to the standard used by the laboratory; (b) uncertainty due to repeatability; (c) uncertainty due to resolution; (d) uncertainty due to hysteresis; (e) uncertainty due to zero drift. The criteria used to compare the results obtained were the normalized error equation (En). The results obtained by the laboratories were compatible according to the criteria |En| <= 1. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by SIM, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

  12. A numerical investigation of fine sediment resuspension in the wave boundary layer - effect of hindered settling and bedforms

    Science.gov (United States)

    Hsu, T. J.; Cheng, Z.; Yu, X.

    2016-02-01

    The wave bottom boundary layer is a major conduit delivering fine terrestrial sediments to the continental margin. Hence, studying the fine sediment resuspension in the wave boundary layer is crucial to the understanding of various components of the earth system, such as carbon cycle. By assuming the settling velocity to be a constant in each simulation, previous turbulence-resolving numerical simulations reveal the existence of three transport modes in the wave boundary layer associated with the sediment availability. As the sediment availability and hence the sediment-induced stable stratification increase, a sequence of transport modes, namely, (I) well-mixed transport, (II) formulation of lutocline resembling a two-layer system, and (III) completely laminarized transport are observed. In general, the settling velocity is a flow variable due to the floc dynamics and hindered settling. This study further investigate the effect of hindered settling. Particularly, for flocs with lower gelling concentrations, the hindered settling effect can play a key role in sustaining large amount of suspended sediment load and results in the laminarized transport (III). For the simulation with a very significant hindered settling effect due to a low gelling concentration, results also indicate the occurrence of gelling ignition, a state in which the erosion rate is always higher than the deposition rate. A condition for the occurrence of gelling ignition is proposed for a range of wave intensities as a function of sediment/floc properties and erodibility parameters. These aforementioned studies are limited to fine sediment transport over a flat bed. However, recent field and laboratory observation show that a small amount of sand fraction can lead to the formation of small bedforms, which can armor the bed while in the meantime enhance near bed turbulence. Preliminary investigation on the effect of bedforms on the resulting transport modes will also be presented.

  13. Final report on CCQM-K79: Comparison of value-assigned CRMs and PT materials: Ethanol in aqueous matrix

    Science.gov (United States)

    Hein, Sebastian; Philipp, Rosemarie; Duewer, David L.; Gasca Aragon, Hugo; Lippa, Katrice A.; Toman, Blaza

    2013-01-01

    -weighted generalized distance regression was used to establish the key comparison reference function (KCRF) relating the assigned values to the repeatability measurements. On the basis of leave-one-out cross-validation, all of the assigned values for all 27 materials were deemed equivalent at the 95% level of confidence. These materials were used to define the KCRF. Parametric bootstrap Monte Carlo was used to estimate 95% level-of-confidence coverage intervals for the degrees of equivalence of materials, d +/- U95(d), and of the participating NMIs, D +/- U95(D). Because of the very wide range of ethanol mass fraction in the materials, these degrees of equivalence are expressed in percent relative form: %d +/- U95(%d) and %D +/- U95(%D). The median of the absolute values of the %D for the participating NMIs is less than 0.05% with a median U95(%D) of less than 1%. These results demonstrate that the participating NMIs have the ability to correctly value-assign CRMs and proficiency test materials for ethanol in aqueous media and similar measurands. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

  14. Observations and modeling of wave-supported sediment gravity flows on the Po prodelta and comparison to prior observations from the Eel shelf

    Science.gov (United States)

    Traykovski, P.; Wiberg, P. L.; Geyer, W. R.

    2007-02-01

    A mooring and tripod array was deployed from the fall of 2002 through the spring of 2003 on the Po prodelta to measure sediment transport processes associated with sediment delivered from the Po River. Observations on the prodelta revealed wave-supported gravity flows of high concentration mud suspensions that are dynamically and kinematically similar to those observed on the Eel shelf [Traykovski, P., Geyer, W.R., Irish, J.D., Lynch, J.F., 2000. The role of wave-induced density-driven fluid mud flows for cross-shelf transport on the Eel River continental shelf. Continental Shelf Research 20, 2113-2140]. Due to the dynamic similarity between the two sites, a simple one-dimensional (1D) across-shelf model with the appropriate bottom boundary condition was used to examine fluxes associated with this transport mechanism at both locations. To calculate the sediment concentrations associated with the wave-dominated and wave-current resuspension, a bottom boundary condition using a reference concentration was combined with an "active layer" formulation to limit the amount of sediment in suspension. Whereas the wave-supported gravity flow mechanism dominated the transport on the Eel shelf, on the Po prodelta flux due to this mechanism is equal in magnitude to transport due to wave resuspension and wind-forced mean currents in the cross-shore direction. Southward transport due to wave resuspension and wind forced mean currents move an order of magnitude more sediment along-shore than the down-slope flux associated wave-supported gravity flows.

  15. Comparison of source-term calculations using the AREST and SYVAC-Vault models: [Final report

    International Nuclear Information System (INIS)

    Apted, M.J.; Engel, D.W.; Garisto, N.C.; LeNeveu, D.M.

    1988-07-01

    A comparison of the calculated radionuclide release from a waste package in a geologic repository has been performed using the verified SYVAC-Vault Model and AREST Model. the purpose of this comparison is to further establish the credibility of these codes for predictive performance assessment and to identify improvements that may be required. A reference case for a Canadian conceptual design with spent fuel as the waste form was chosen to make an initial comparison. The results from the two models were in good agreement, including peak release rates, time to reach peak release, and long term release rates. Differences in results from the two models are attributed to differences in computational approaches. Studies of the effects of sorption, convective flow, distributed containment failure, and precipitation are identified as key areas for further comparisons and are currently in progress. 11 refs., 3 figs., 5 tabs

  16. Global Annual Final AC Yield Comparison between HCPV and c-Si PV

    Directory of Open Access Journals (Sweden)

    Juan Pablo Ferrer-Rodríguez

    2015-01-01

    Full Text Available A worldwide comparison of the annual yield between conventional c-Si photovoltaic (PV technology and high concentrated photovoltaic (HCPV technology is presented. The idea of this paper is to find the most appropriate locations for HCPV systems in terms of the annual energy produced when comparing to fixed tilt PV systems and two-axis oriented PY systems. For estimating the annual energy generation, the method of the Performance Ratio is used. For some locations with high annual direct normal irradiation values, which are distributed around the world, HCPV systems are found to be more advantageous than fixed tilt PV systems. World maps showing this comparison are presented.

  17. Problems of comparison

    International Nuclear Information System (INIS)

    Horn, G.

    1989-01-01

    This paper reports on determination of the balance of forces embrace a much wider area than the scope of mere numerical comparisons. In Europe that there is rough parity between the conventional forces of WTO and NATO, we do not claim that both sides have the same forces. The balance of forces cannot be considered except in view of purpose and circumstances. In our case, the balance of forces in Europe can be taken to mean that neither side has enough strength to impose its will on the other by military force. Of course, this type of comparison cannot be used at the disarmament talks to take stock of armed forces and to determine the final result of reductions, or of the reduction process. Nevertheless it is very important to know that the talks will be conducted against the background and that the final result should not, in this one respect, be any different from the point of departure

  18. Coastal resuspension

    International Nuclear Information System (INIS)

    Garland, J.A.

    1991-11-01

    There are several potential mechanisms for the suspension in air of radioactive or other pollutants from coastal sea water, beaches, mud banks and salt marshes. Available measurements rarely allow these mechanisms to be distinguished. The limited data show a broad spread of results. When normalised by the concentration of radionuclides in beach sediments most of the data indicate concentrations equivalent to 1 to 30 μg m -3 of sediment suspended in air, both for sampling sites on open coasts and near estuaries. Limited evidence for sampling sites located on salt marshes indicates about 0.2 μg m -3 of suspended sediment. These values represent the aggregate effect of the mechanisms that operate at a limited number of coastal locations. At other locations it is possible that additional mechanisms will contribute to the suspension of sediment. (Author)

  19. Multiloop integral system test (MIST): Final report, Inter-group comparisons

    Energy Technology Data Exchange (ETDEWEB)

    Gloudemans, J.R.

    1989-07-01

    The multiloop integral system test (MIST) was part of a multiphase program started in 1983 to address small-break loss-of-coolant accidents (SBLOCAs) specific to Babcock and Wilcox-designed plants. MIST was sponsored by the US Nuclear Regulatory Commission, the Babcock and Wilcox Owners Group, the Electric Power Research Institute, and Babcock and Wilcox. The unique features of the Babcock and Wilcox design, specifically the hot leg U-bends and steam generators, prevented the use of existing integral system data or existing integral system facilities to address the thermal-hydraulic SBLOCA questions. MIST and two other supporting facilities were specifically designed and constructed for this program, and an existing facility -- the once-through integral system (OTIS) -- was also used. Data from MIST and the other facilities will be used to benchmark the adequacy of system codes, such as RELAP5 and TRAC, for predicting abnormal plant transients. The individual tests are described in detail in Volumes 2 through 8 and Volume 11, and are summarized in Volume 1. Inter-group comparisons are addressed in this document, Volume 9. These comparisons are grouped as follows: mapping versus SBLOCA transients, SBLOCA, pump effects, and the effects of noncondensible gases. Appendix A provides an index and description of the microfiched plots for each test, which are enclosed with the corresponding Volumes 2 through 8. 147 figs., 5 tabs.

  20. KEY COMPARISON: Final report on CCQM-K63.a,b: Non-peptide hormones in serum: cortisol and progesterone

    Science.gov (United States)

    S-C Tai, Susan; Duewer, David L.

    2010-01-01

    /MS-based cortisol results is 100.4 ng/g with a relative standard deviation (%RSD) of 1.1%. The mean value for the seven ID/MS-based progesterone originally reported results is 2.83 with a %RSD of 1.8%. While a number of the reported results were not eligible to be used in establishing the KCRVs, the KCRVs as estimated from just the eligible results agree very well with these means. The excellent among-participant agreement indicates that ID/MS-based measurement procedures can provide precise and true results for steroid hormones at levels greater than about 1 ng/g. The progesterone result reported by a laboratory using a non-isotopically labelled internal standard was about 11% larger than the KCRV. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

  1. KEY COMPARISON Report to the CCT on key comparison EUROMET.T-K6 (EUROMET Project no. 621): Comparison of the realizations of local dew/frost-point temperature scales in the range -50 °C to +20 °C

    Science.gov (United States)

    Heinonen, Martti

    2010-01-01

    The first humidity CIPM key comparison, CCT-K6, will be completed in 2010. The corresponding European regional key comparison, EUROMET.T-K6, was carried out in 2004 to 2008. National metrology institutes from 24 countries participated in the comparison. The comparison covered the dew-point temperature range from -50 °C to +20 °C. It was organized as three parallel loops with two specially manufactured precision chilled mirror hygrometers as transfer standards in each loop. The comparison scheme was designed to ensure high quality results with evenly spread workload for the participants. MIKES was coordinating the project. This report presents the results of the comparison and provides detailed information on the measurements performed by all participating laboratories and the analysis of the results. Conclusions on the equivalence of the dew-point temperature standards are drawn on the basis of calculated bilateral degrees of equivalence and deviations from EURAMET comparison reference values (ERV). Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCT, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

  2. Final report on CCQM-K80: Comparison of value-assigned CRMs and PT materials: Creatinine in human serum

    Science.gov (United States)

    Camara, Johanna E.; Duewer, David L.; Gasca Aragon, Hugo; Lippa, Katrice A.; Toman, Blaza

    2013-01-01

    regression was used to establish the key comparison reference function (KCRF) relating the assigned values to the repeatability measurements. Parametric bootstrap Monte Carlo was used to estimate 95% level-of-confidence coverage intervals for the degrees of equivalence of materials, d +/- U95(d), and of the participating NMIs, D +/- U95(D). Because of the wide range of creatinine mass fraction in the materials, these degrees of equivalence are expressed in percent relative form: %d +/- U95(%d) and %D +/- U95(%D). On the basis of leave-one-out cross-validation, the assigned values for 16 of the 17 materials were deemed equivalent at the 95% level of confidence. These materials were used to define the KCRF. The excluded material was identified as having a marginally underestimated assigned uncertainty, giving it large and potentially anomalous influence on the KCRF. However, this material's %d of 1.4 +/- 1.5 indicates that it is equivalent with the other materials at the 95% level of confidence. The median |%d| for all 17 of the materials is 0.3 with a median U95(%d) of 1.9. All of these higher-order CRMs for creatinine in human serum are equivalent within their assigned uncertainties. The median |%D| for the participating NMIs is 0.3 with a median U95(%D) of 2.1. These results demonstrate that all participating NMIs have the ability to correctly value-assign CRMs and proficiency test materials for creatinine in human serum and similar measurands. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

  3. Bilateral comparison of 100 pF standards (ongoing BIPM key comparison BIPM.EM-K14.b) between the NSAI-NML (Ireland) and the BIPM

    Science.gov (United States)

    Gournay, Pierre; Power, Oliver

    2017-01-01

    This report presents the results of a bilateral comparison of capacitance at 100 pF between the NSAI-NML (Ireland) and the BIPM carried out in 2016. This comparison forms part of the ongoing BIPM key comparison BIPM.EM-K14.b in which the BIPM is the pilot laboratory. Two 100 pF travelling standards belonging to the BIPM were used in this comparison carried out with an 'A-B-A' pattern of measurements. The standards were measured first at the BIPM for a period of about one month, then for a similar period at the NSAI-NML, and finally again at the BIPM. The measurand was the two terminal-pair capacitance at a frequency of 1000 Hz, for a measuring rms voltage of 15 V. The results from the NSAI-NML and the BIPM were found to be in relatively good agreement, with a difference smaller than the relative expanded uncertainty (95 % confidence, k = 2) of 0.85 × 10-6. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

  4. Bilateral comparison of 1 Ω standards (ongoing BIPM key comparison BIPM.EM-K13.a) between the NSAI-NML (Ireland) and the BIPM

    Science.gov (United States)

    Goebel, R.; Power, O.; Fletcher, N.; Stock, M.

    2012-01-01

    This report describes the results obtained from a NML(Ireland)-BIPM bilateral comparison of 1 Ω resistance standards in 2010. The comparison was carried out in the framework of the BIPM ongoing key comparison BIPM.EM-K13.a. Two BIPM 1 Ω travelling standards of CSIRO type were calibrated first at the BIPM, then at the NMLI and again at the BIPM after their return. The stability of the transfer standard was such that the uncertainty associated with the transfer was significantly smaller than the uncertainty arising from the calibrations. The mean difference between the NMLI and the BIPM calibrations was found to be just within the expanded uncertainty (k = 2) of the comparison. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

  5. A New Comparison Principle for Impulsive Functional Differential Equations

    Directory of Open Access Journals (Sweden)

    Gang Li

    2015-01-01

    Full Text Available We establish a new comparison principle for impulsive differential systems with time delay. Then, using this comparison principle, we obtain some sufficient conditions for several stabilities of impulsive delay differential equations. Finally, we present an example to show the effectiveness of our results.

  6. Reprint of: A numerical investigation of fine sediment resuspension in the wave boundary layer-Uncertainties in particle inertia and hindered settling

    Science.gov (United States)

    Cheng, Zhen; Yu, Xiao; Hsu, Tian-Jian; Balachandar, S.

    2016-05-01

    The wave bottom boundary layer is a major conduit delivering fine terrestrial sediments to continental margins. Hence, studying fine sediment resuspensions in the wave boundary layer is crucial to the understanding of various components of the earth system, such as carbon cycles. By assuming the settling velocity to be a constant in each simulation, previous turbulence-resolving numerical simulations reveal the existence of three transport modes in the wave boundary layer associated with sediment availabilities. As the sediment availability and hence the sediment-induced stable stratification increases, a sequence of transport modes, namely, (I) well-mixed transport, (II) formulation of lutocline resembling a two-layer system, and (III) completely laminarized transport are observed. In general, the settling velocity is a flow variable due to hindered settling and particle inertia effects. Present numerical simulations including the particle inertia suggest that for a typical wave condition in continental shelves, the effect of particle inertia is negligible. Through additional numerical experiments, we also confirm that the particle inertia tends (up to the Stokes number St = 0.2) to attenuate flow turbulence. On the other hand, for flocs with lower gelling concentrations, the hindered settling can play a key role in sustaining a large amount of suspended sediments and results in the laminarized transport (III). For the simulation with a very significant hindered settling effect due to a low gelling concentration, results also indicate the occurrence of gelling ignition, a state in which the erosion rate is always higher than the deposition rate. A sufficient condition for the occurrence of gelling ignition is hypothesized for a range of wave intensities as a function of sediment/floc properties and erodibility parameters.

  7. Long-term Measurement of Sediment Resuspension and Gas Hydrate Stability at a Gulf of Mexico Seep Site

    Science.gov (United States)

    Vardaro, M. F.; Bender, L. C.; MacDonald, I. R.

    2003-12-01

    To study the temporal topographic and hydrologic changes in Gulf of Mexico cold seeps, we deployed a deep-sea time-lapse camera, several temperature probes and an ADCP mooring at the continental shelf seep community surrounding a gas hydrate outcropping. The digital camera recorded one still image every six hours for three months in 2001, every two hours for the month of June 2002 and every six hours for the month of July 2002. A pair of 300 kHz Workhorse acoustic Doppler current profilers (ADCPs) attached to a 540 meter-long mooring were anchored approximately 2 km from the site in 2002. Temperature probes were deployed at the site over the entire experimental period. The data recovered provide a comprehensive record of gas hydrate mound processes. We calculated biological activity by identifying fauna observed in the time-lapse record and recording the number of individuals and species seen in each image. 1,381 individual organisms representing over 20 species were observed. An average of 4.6 (+/-3.0) organisms were seen in each frame during the three-month deployment, while 3.6 (+/-4.2) were seen per frame in the one-month deployment. An extensive amount of sediment suspension and redistribution occurred during the deployment period. By digitally analyzing the luminosity of the water column above the mound and plotting the results over time the turbidity at the site could be quantified. A 24.1-hour diurnal pattern can be seen in the record, indicating a possible tidal or inertial component to deep-sea currents in this area. Contrary to expectations, there was no major change in shape or size of the gas hydrate outcrop being studied. This indicates a higher degree of stability than laboratory studies or prior in situ observations have shown. The stable topography of the gas hydrate mound combines with high organic output and sediment turnover to serve as a focus of benthic predatory activity. The frequency and recurrence of sediment resuspension indicate that

  8. KEY COMPARISON: Report on the Regional Comparison COOMET.AUV.A-K3

    Science.gov (United States)

    Barrera-Figueroa, Salvador; Nielsen, Lars; Rasmussen, Knud

    2007-01-01

    COOMET.AUV.A-K3 is a Regional Comparison that supplements the Key Comparison CCAUV.A-K3 organized by the CCAUV. The participating NMIs are GUM (Poland), INM (Romania), VNIIFTRI (Russia) and DP-NDI 'Systema' (Ukraine). The role of Pilot laboratory was undertaken by DPLADFM (Denmark). The measurements took place between May 2005 and February 2006. The time schedule was organized in a single star configuration. Initially, two LS2aP microphones were circulated. However, a sudden change of sensitivity of one of them forced the inclusion of an additional microphone. Nevertheless, the analysis was performed on all microphones involved. This report includes the measurement results from the participants, information about their calibration methods, and the analysis leading to the assignation of degrees of equivalence and the link to the CCAUV.A-K3. Main text. To reach the main text of this paper, click on Final Report. The final report has been peer-reviewed and approved for publication by the CCAUV, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

  9. Comparison versus reminding.

    Science.gov (United States)

    Tullis, Jonathan G; Goldstone, Robert L

    2016-01-01

    Comparison and reminding have both been shown to support learning and transfer. Comparison is thought to support transfer because it allows learners to disregard non-matching features of superficially different episodes in order to abstract the essential structure of concepts. Remindings promote memory for the individual episodes and generalization because they prompt learners to retrieve earlier episodes during the encoding of later related episodes and to compare across episodes. Across three experiments, we compared the consequences of comparison and reminding on memory and transfer. Participants studied a sequence of related, but superficially different, proverb pairs. In the comparison condition, participants saw proverb pairs presented together and compared their meaning. In the reminding condition, participants viewed proverbs one at a time and retrieved any prior studied proverb that shared the same deep meaning as the current proverb. Experiment 1 revealed that participants in the reminding condition recalled more proverbs than those in the comparison condition. Experiment 2 showed that the mnemonic benefits of reminding persisted over a one-week retention interval. Finally, in Experiment 3, we examined the ability of participants to generalize their remembered information to new items in a task that required participants to identify unstudied proverbs that shared the same meaning as studied proverbs. Comparison led to worse discrimination between proverbs related to studied proverbs and proverbs unrelated to studied proverbs than reminding. Reminding supported better memory for individual instances and transfer to new situations than comparison.

  10. Bilateral comparison of 10 kΩ standards (ongoing BIPM key comparison BIPM.EM-K13.b) between the NSAI-NML (Ireland) and the BIPM

    Science.gov (United States)

    Goebel, R.; Power, O.; Fletcher, N.; Stock, M.

    2012-01-01

    This report describes the results obtained from a NML(Ireland)-BIPM bilateral comparison of 10 kΩ resistance standards in 2010. The comparison was carried out in the framework of the BIPM ongoing key comparison BIPM.EM-K13.b. Two BIPM 10 kΩ travelling standards of SR104 type were calibrated first at the BIPM, then at the NMLI and again at the BIPM after their return. The stability of the transfer standards was such that the uncertainty associated with the transfer was significantly smaller than the uncertainty arising from the calibrations. The NMLI and the BIPM calibrations were found to be in agreement, with a mean difference smaller than the standard uncertainty of the comparison. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

  11. KEY COMPARISON: CCEM.RF-K9: International comparison of thermal noise standards between 12.4 GHz and 18 GHz (GT-RF/99-1)

    Science.gov (United States)

    Allal, Djamel; Achkar, Joseph

    2006-01-01

    An international comparison of thermal noise-power measurements has been carried out among five national metrology institutes between 12.4 GHz and 18 GHz. Four transfer standards were measured. The following national institutes participated: BNM-LCIE (France), NPL (United Kingdom), PTB (Germany), NIST (United States of America) and VNIIFTRI (Russia). The Bureau National de Métrologie-Laboratoire Central des Industries Electriques (France) acted as the pilot laboratory for the comparison. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

  12. Final report on EURAMET.QM-K12: EURAMET key comparison on the determination of the mass fraction of creatinine in serum

    Science.gov (United States)

    Bell, David; Hopley, Chris; Ellison, Stephen L. R.; O'Connor, Gavin

    2013-01-01

    equivalence of participants in CCQM-K12. The range of participants' results in EURAMET.QM-K12 for both levels (2% and 3% respectively for materials A and B) was greater than the 1% achieved in CCQM-K12. However, it was concluded that this study was suitable to support CMCs for creatinine in serum for 1 µg/g to 100 µg/g with uncertainties at the 1% to 1.5% level. This was found to be fit for purpose and consistent with the majority of CMCs currently approved. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

  13. SUPPLEMENTARY COMPARISON Bilateral comparison on the calibrations of hydrometers for liquid density between INRIM-Italy and INMETRO-Brazil: SIM.M.D-S2

    Science.gov (United States)

    Lorefice, Salvatore; Malta, Dalni; Julio Pinheiro, José; Marteleto, Paulo Roberto

    2010-01-01

    The results of the SIM.M.D-S2 bilateral comparison between INRIM-Italy and INMETRO-Brazil are summarized in this report. The aims of this comparison were to check the stated uncertainty levels and the degrees of equivalence between the two institutes on the calibration of hydrometers for liquid density in the range of 800 kg m-3 to 1000 kg m-3 at 20 ºC, by means of two transfer standards of excellent metrological characteristics. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by SIM, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

  14. Final Energy Consumption Trends and Drivers in Czech Republic and Latvia

    Directory of Open Access Journals (Sweden)

    Zhiqian Yu

    2017-08-01

    Full Text Available This paper analyses the trends of final energy consumption in Latvia and Czech Republic. Analysis of final energy consumption during 2000-2013 period indicated the main driving forces of final energy consumption during and after world financial crisis of 2008. The paper aimed to evaluate the impact of economic activity and other factors on final energy consumption. The decomposition of the final energy consumption is assessed by analyzing effect of different drivers by the main end-users sector (industry, transport, households, agriculture, services, activity, demography, lifestyles, structural effects, energy savings etc. The results show that the reduction in final energy consumption in most EU members states before and after year 2008 can be related to the decline in energy intensities within endusers sectors. At the same time, the increase in final energy intensity after the year 2008 is attributed to expansion of energy demand sectors. Comparison of final energy consumption trends and drivers in Latvia and Czech Republic indicated that Czech Republic implemented more policies and measures in industry and tertiary sector and this provided for final energy consumption decreased and huge energy savings in these sectors.

  15. Final results for the neutron detector efficiencies

    International Nuclear Information System (INIS)

    Zhou Zuying; Tang Hongqing; Qi Bujia; Du Yanfeng; Zhou Chenwei; Xia Haihong; Chen Zemin; Chen Zhenpeng; Chen Yingtang

    1998-01-01

    Final results for neutron detector efficiencies of a liquid organic scintillator are presented. The comparisons of efficiency results to calculations with discrimination against γ-rays and without n-γ discrimination are shown out and discussed. The measured relative neutron detection efficiency of a liquid organic scintillator with the PSD constraint active is in good agreement with SCINFUL calculations from 9 to 40 Mev and NEFF7 calculations from 9 to 20 Mev, the upper limit of the latter code

  16. Final report of APMP.QM-S6: clenbuterol in porcine meat

    Science.gov (United States)

    Sin, D. W.-M.; Ho, C.; Yip, Y.-C.

    2016-01-01

    At the CCQM Organic Analysis Working Group (OAWG) Meeting held in April 2012 and the APMP TCQM Meeting held in November 2012, an APMP supplementary comparison (APMP.QM-S6) on the determination of clenbuterol in porcine meat was supported by the OAWG and APMP TCQM. This comparison was organized by the Government Laboratory, Hong Kong. In order to accommodate a wider participation, a pilot study (APMP.QM-P22) was run in parallel to APMP.QM-S6. This study provided the means for assessing the measurement capabilities for determination of low-polarity measurands in a procedure that requires extraction, clean-up, analytical separation, and selective detection in a food matrix. A total of 7 institutes registered for the supplementary comparison and 6 of them submitted their results. 4 results were included for SCRV calculation. All participating laboratories applied Isotope Dilution Liquid Chromatography-Tandem Mass Spectrometry (ID-LCMS/MS) technique with clenbuterol-d9 as internal standard spiked for quantitation in this programme. KEY WORDS FOR SEARCH APMP.QM-S6 and Clenbuterol Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

  17. Report on NIM-NMC bilateral comparison: SPRT calibration comparison from -190°C to 420°C

    Science.gov (United States)

    Sun, Jianping; Ye, Shaochun; Wang, Li; Zhang, Jintao; Kho, Haoyuan

    2016-01-01

    A bilateral comparison of local realization of the International temperature scale of 1990 (ITS-90) between National Institute of Metrology (NIM) and National Metrology Centre (NMC) was carried out over the temperature range from -190°C to 420°C. It involved six fixed points including the argon triple point, the mercury triple point, the triple point of water, the melting point of gallium, the freezing point of tin and the freezing point of zinc. In 2009, NMC asked NIM to participate in a bilateral comparison to link the NMC results to the Consultative Committee for Thermometry Key comparison 3 (CCT-K3) and facilitate the NMC's Calibration and measurement capabilities (CMCs) submission. This comparison was agreed by NIM and Asia Pacific Metrology Programme (APMP) in 2009, and registered in the Key Comparison Database (KCDB) in 2010 as CCT-K3.2. NMC supplied two 25 Ω fused silica sheath standard platinum resistance thermometers (SPRTs) as traveling standards. One of them was used at the Ga, Sn and Zn fixed points, while the other one was used at the Ar and Hg fixed point. NMC measured them before and after NIM measurement. During the comparison, a criterion for the SPRT was set as the stability at the triple point of water to be less than 0.3 mK. The results for both laboratories are summarized. A proposal for linking the NMC's comparison results to CCT-K3 is presented. The difference between NMC and NIM and the difference between NMC and the CCT-K3 Average Reference Value (ARV) using NIM as a link are reported with expanded uncertainties at each measured fixed point. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCT, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

  18. Angle comparison using an autocollimator

    Science.gov (United States)

    Geckeler, Ralf D.; Just, Andreas; Vasilev, Valentin; Prieto, Emilio; Dvorácek, František; Zelenika, Slobodan; Przybylska, Joanna; Duta, Alexandru; Victorov, Ilya; Pisani, Marco; Saraiva, Fernanda; Salgado, Jose-Antonio; Gao, Sitian; Anusorn, Tonmueanwai; Leng Tan, Siew; Cox, Peter; Watanabe, Tsukasa; Lewis, Andrew; Chaudhary, K. P.; Thalmann, Ruedi; Banreti, Edit; Nurul, Alfiyati; Fira, Roman; Yandayan, Tanfer; Chekirda, Konstantin; Bergmans, Rob; Lassila, Antti

    2018-01-01

    Autocollimators are versatile optical devices for the contactless measurement of the tilt angles of reflecting surfaces. An international key comparison (KC) on autocollimator calibration, EURAMET.L-K3.2009, was initiated by the European Association of National Metrology Institutes (EURAMET) to provide information on the capabilities in this field. The Physikalisch-Technische Bundesanstalt (PTB) acted as the pilot laboratory, with a total of 25 international participants from EURAMET and from the Asia Pacific Metrology Programme (APMP) providing measurements. This KC was the first one to utilise a high-resolution electronic autocollimator as a standard. In contrast to KCs in angle metrology which usually involve the full plane angle, it focused on relatively small angular ranges (+/-10 arcsec and +/-1000 arcsec) and step sizes (10 arcsec and 0.1 arcsec, respectively). This document represents the approved final report on the results of the KC. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCL, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

  19. A plane-wave final-state theory of ATI

    International Nuclear Information System (INIS)

    Parker, J.S.; Clark, C.W.

    1993-01-01

    A Fermi Golden Rule calculation of ionization cross-sections provides us with the simplest example of a plane-wave final-state theory. In this method the final (unbound) state is modeled as a plane wave, an approximation that generally gives best results in the high energy limit in which the affect of the atomic potential on the final state can be neglected. A cross-section is then calculated from the matrix element connecting the bound initial state with the final state. The idea of generalizing this method to model transitions among unbound states is credited to L.V. Keldysh, and a number of related formalisms have been proposed that are consistent with the general features of experimental data. Here we describe a plane-wave final-state model of ATI that is in the spirit of these theories, but differs significantly in its implementation and predictions. We will present a comparison of the predictions of the plane-wave model with those of a full numerical integration of the time-dependent Schrodinger equation for atomic hydrogen in a radiation field. The theory and the numerical integration give good qualitative agreement in their predictions of photoelectron spectra over about 14 orders of magnitude

  20. SUPPLEMENTARY COMPARISON: Report of the bilateral comparison of the calibrations of hydrometers for liquid density determination between CENAM-Mexico and INRIM-Italy: SIM.M.D-S1

    Science.gov (United States)

    Becerra, Luis Omar; Lorefice, Salvatore

    2009-01-01

    Hydrometers are instruments usually made of glass which are widely used for different levels of precision to measure liquid density and related quantities to control different products and processes. This bilateral comparison on the calibration of hydrometers shows that results reported by CENAM-Mexico and INRIM-Italy are consistent within the claimed uncertainty in the range of 800 kg/m3 to 1200 kg/m3. This bilateral comparison is intended to link the two regional comparisons SIM.M.D-K4 and EURAMET.D-K4. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by SIM, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

  1. Comparison between the KBS-3 method and the deep borehole for final disposal of spent nuclear fuel

    International Nuclear Information System (INIS)

    Grundfelt, Bertil

    2010-09-01

    In this report a comparison is made between disposal of spent nuclear fuel according to the KBS-3 method with disposal in very deep boreholes. The objective has been to make a broad comparison between the two methods, and by doing so to pinpoint factors that distinguish them from each other. The ambition has been to make an as fair comparison as possible despite that the quality of the data of relevance is very different between the methods

  2. Bilateral comparison of 100 pF capacitance standards (ongoing BIPM key comparison BIPM.EM-K14.b) between the NSAI-NML, Ireland, and the BIPM, March-August 2011

    Science.gov (United States)

    Power, O.; Moran, A.; Fletcher, N.; Goebel, R.; Stock, M.

    2015-01-01

    This report gives the result of a bilateral comparison of capacitance between the NSAI-NML (Ireland) and the BIPM carried out in 2011. Two 100 pF travelling standards belonging to the BIPM were used. The comparison was carried out with an 'A-B-A' pattern of measurements; the standards were measured first at the BIPM for a period of about one month, then for a similar period at the NSAI-NML, and finally again at the BIPM. The measurand was the two terminal-pair capacitance at a frequency of 1000 Hz, for a measuring voltage of 15 V. The BIPM was the pilot laboratory, and the comparison forms part of the ongoing BIPM key comparison BIPM.EM-K14.b. The results from the NSAI-NML and the BIPM were found to be in good agreement, with a difference smaller than the relative expanded uncertainty (95 % confidence, k = 2) of 0.66 × 10-6. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

  3. Bilateral comparison of 10 pF capacitance standards (ongoing BIPM key comparison BIPM.EM-K14.a) between the NSAI-NML, Ireland, and the BIPM, March-August 2011

    Science.gov (United States)

    Power, O.; Moran, A.; Fletcher, N.; Goebel, R.; Stock, M.

    2015-01-01

    This report gives the result of a bilateral comparison of capacitance between the NSAI-NML (Ireland) and the BIPM carried out in 2011. Two 10 pF travelling standards belonging to the BIPM were used. The comparison was carried out with an 'A—B—A' pattern of measurements; the standards were measured first at the BIPM for a period of about one month, then for a similar period at the NSAI-NML, and finally again at the BIPM. The measurand was the two terminal-pair capacitance at a frequency of 1000 Hz for a measuring voltage of 15 V. The BIPM was the pilot laboratory, and the comparison forms part of the ongoing BIPM key comparison BIPM.EM-K14.a. The results from the NSAI-NML and the BIPM were found to be in good agreement, with a difference smaller than the relative expanded uncertainty (95 % confidence, k = 2) of 2.5 × 10-6. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

  4. Pollution loads from stormwater overflows

    International Nuclear Information System (INIS)

    Bonomo, L.

    1991-01-01

    The knowledge of the volume of combined effluents outflowing from overflows is not enough to allow a direct evaluation of polluting loads discharged into final receptors; the hypothesis of complete mixing between sewage and stormwater flow, fed in at a pollutant concentration level equal to zero, hasn't proved to be successful. The amount of the outflowing loads largely depends on the contamination of the stormwater runoff before inflow into the drainage system and on sedimentation and resuspension phenomena. This paper reports the main aspects connected with wet and dry atmospheric deposition of pollutants and with paved surface wash-out phenomena. The origin of pollutants flush, due to the resuspension and mass transport of polluting substances stored up in the sewer during draughts, is also described. Attention is drawn to the importance of the behaviour of the different pollutants with respect to the sedimentation phenomena. Reference is made to evaluations conducted on a drainage system for the recovery of a small pre-alpine lake

  5. Experimental determination of the flood wave transformation and the sediment resuspension in a small regulated stream in an agricultural catchment

    Directory of Open Access Journals (Sweden)

    D. Zumr

    2017-11-01

    Full Text Available This paper presents the methodology used for artificial flood experiments conducted in a small artificial, trained (regulated channel on the Nučice experimental agricultural catchment (0.5 km2, central Czech Republic, and the results of the experiments. The aim was to monitor the transformation of the flood wave and the sediment transport within the channel. Two series of experiments were carried out in contrasting initial conditions: (a in September, when the stream banks were dry, the baseflow was negligible, and the channel was fully overgrown with vegetation; and (b in March, when the stream banks were almost water saturated, the baseflow was above the annual average, and there was no vegetation present. Within each campaign, three successive flood waves, each with an approximate volume of 17 m3 and peak flow of ca. 40 L s−1, were pumped into the upper part of the catchment drainage channel. The transformation of the flood wave and the sediment transport regime within an approximately 400 m long channel section were monitored by measuring the discharge, the turbidity, and the electrical conductivity in three profiles along the stream. On the basis of the results, it was concluded that there is a considerable amount of deposited sediment, even in the well-trained and straight channel that can be re-mobilized by small floods. Part of the recorded sediment therefore originates from the particles deposited during previous soil erosion events. The flood waves initiated in dissimilar instream conditions progressed differently – we show that the saturation of the channel banks, the stream vegetation and the actual baseflow had a strong influence on the flood transformation and the sediment regime in the channel. The sediment moves quickly in winter and early spring, but in the later part of the year the channel serves as a sediment trap and the resuspension is slower, if dense vegetation is present.

  6. International comparison of resistance thermometers between NMIs from Spain, Mexico and Andean countries

    Science.gov (United States)

    del Campo, D.; Ruiz, V. C.; Méndez-Lango, E.; Córdova, L.; von Borries, E.; Sánchez, C. A.; Arévalo, A.; Aguilera, B.; Guillén, E.; Cabrera, C.; Quintana, L.

    2013-09-01

    An international comparison on semi-standard Platinum Resistance Thermometers (PRTs) among the National Metrology Institutes (NMIs) of Spain, Mexico and the Andean Countries (Bolivia, Colombia, Ecuador, Peru and Venezuela) began in 2004 and was successfully completed in 2005. Two PRTs were circulated (hand carried) and compared from -40 °C up to 250 °C. The Centro Español de Metrología (Spanish NMI), CEM, was the pilot laboratory and the Centro Nacional de Metrología (Mexican NMI), CENAM, was the co-pilot laboratory. This paper shows the details of the comparison and the final results as they were presented in the approved final report of the comparison in September of 2005.

  7. KEY COMPARISON: Comparison of the standards for absorbed dose to water of the VNIIFTRI, Russia and the BIPM in 60Co γ rays

    Science.gov (United States)

    Allisy-Roberts, P. J.; Kessler, C.; Burns, D. T.; Berlyand, V.; Berlyand, A.

    2010-01-01

    A new comparison of the standards for absorbed dose to water of the All-Russian Scientific Research Institute for Physical-Technical and Radiotechnical Measurements (VNIIFTRI), Russia and of the Bureau International des Poids et Mesures (BIPM) has been made in 60Co gamma radiation in 2009. The results show that the VNIIFTRI and the BIPM standards for absorbed dose to water are in agreement, yielding a mean ratio of 0.9976 for the calibration coefficients of the transfer chambers, the difference from unity being within the combined standard uncertainty (0.0043) for this result. This result is consistent with the earlier 2001 comparison result of 0.9967 (43). The updated degrees of equivalence for the VNIIFTRI are compared with those of the other national metrology institutes as presented in the BIPM key comparison database. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCRI Section I, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

  8. Environmental hazard assessment of a marine mine tailings deposit site and potential implications for deep-sea mining.

    Science.gov (United States)

    Mestre, Nélia C; Rocha, Thiago L; Canals, Miquel; Cardoso, Cátia; Danovaro, Roberto; Dell'Anno, Antonio; Gambi, Cristina; Regoli, Francesco; Sanchez-Vidal, Anna; Bebianno, Maria João

    2017-09-01

    Portmán Bay is a heavily contaminated area resulting from decades of metal mine tailings disposal, and is considered a suitable shallow-water analogue to investigate the potential ecotoxicological impact of deep-sea mining. Resuspension plumes were artificially created by removing the top layer of the mine tailings deposit by bottom trawling. Mussels were deployed at three sites: i) off the mine tailings deposit area; ii) on the mine tailings deposit beyond the influence from the resuspension plumes; iii) under the influence of the artificially generated resuspension plumes. Surface sediment samples were collected at the same sites for metal analysis and ecotoxicity assessment. Metal concentrations and a battery of biomarkers (oxidative stress, metal exposure, biotransformation and oxidative damage) were measured in different mussel tissues. The environmental hazard posed by the resuspension plumes was investigated by a quantitative weight of evidence (WOE) model that integrated all the data. The resuspension of sediments loaded with metal mine tails demonstrated that chemical contaminants were released by trawling subsequently inducing ecotoxicological impact in mussels' health. Considering as sediment quality guidelines (SQGs) those indicated in Spanish action level B for the disposal of dredged material at sea, the WOE model indicates that the hazard is slight off the mine tailings deposit, moderate on the mine tailings deposit without the influence from the resuspension plumes, and major under the influence of the resuspension plumes. Portmán Bay mine tailings deposit is a by-product of sulphide mining, and despite differences in environmental setting, it can reflect the potential ecotoxic effects to marine fauna from the impact of resuspension of plumes created by deep-sea mining of polymetallic sulphides. A similar approach as in this study could be applied in other areas affected by sediment resuspension and for testing future deep-sea mining sites in

  9. Comparison of energy efficiency solutions for households applying electrical energy measurement of individual consumers - Final report; Vergleich verschiedener Effizienzloesungen mit Einzelverbrauchermessung fuer Haushalte - Schlussbericht

    Energy Technology Data Exchange (ETDEWEB)

    Fercu, M.; Kistler, R.

    2009-12-15

    This final report for the Swiss Federal Office of Energy (SFOE) discusses the growing demand for so-called 'Energy Feedback Systems' being experienced by numerous energy utilities. These systems allow the presentation of highly-detailed (electrical) energy consumption information to the residents of households. The aim of these systems is discussed which is to sensitize the customers and provide them with a higher level of awareness of their personal energy consumption in order to motivate them to conserve power. This short report analyses existing and near-future systems that can provide power consumption information and which can also automate the operation of household electrical devices. The report focuses on the comparison of four commercial systems available in Switzerland that conform to basic requirements. Furthermore, information on other systems is also provided.

  10. Comparison of energy efficiency solutions for households applying electrical energy measurement of individual consumers - Final report; Vergleich verschiedener Effizienzloesungen mit Einzelverbrauchermessung fuer Haushalte - Schlussbericht

    Energy Technology Data Exchange (ETDEWEB)

    Fercu, M.; Kistler, R.

    2009-12-15

    This final report for the Swiss Federal Office of Energy (SFOE) discusses the growing demand for so-called 'Energy Feedback Systems' being experienced by numerous energy utilities. These systems allow the presentation of highly-detailed (electrical) energy consumption information to the residents of households. The aim of these systems is discussed which is to sensitize the customers and provide them with a higher level of awareness of their personal energy consumption in order to motivate them to conserve power. This short report analyses existing and near-future systems that can provide power consumption information and which can also automate the operation of household electrical devices. The report focuses on the comparison of four commercial systems available in Switzerland that conform to basic requirements. Furthermore, information on other systems is also provided.

  11. Model validation studies of solar systems, Phase III. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Lantz, L.J.; Winn, C.B.

    1978-12-01

    Results obtained from a validation study of the TRNSYS, SIMSHAC, and SOLCOST solar system simulation and design are presented. Also included are comparisons between the FCHART and SOLCOST solar system design programs and some changes that were made to the SOLCOST program. Finally, results obtained from the analysis of several solar radiation models are presented. Separate abstracts were prepared for ten papers.

  12. Sediment Properties along Gradients of Siltation in South-East Asia

    DEFF Research Database (Denmark)

    Kamp-Nielsen, Lars; Vermaat, J.; Wesseling, I.

    2002-01-01

    sediment properties, SE Asia, siltation, resuspension, iron, calcium, seagrass, corals, mangroves, mudflats......sediment properties, SE Asia, siltation, resuspension, iron, calcium, seagrass, corals, mangroves, mudflats...

  13. Mechanical resuspension of 239Pu from unpaved roads

    International Nuclear Information System (INIS)

    Hodgin, C.R.

    1982-01-01

    The impacts of resuspended plutonium from two unpaved roads at the Rocky Flats Plant on nearby air samplers were investigated. Because the sources were complex fugitive dust emitters and because of the small source-receptor distances, traditional dispersion modeling techniques could not be employed. Thus two specialized techniques, one for fugitive dust emissions and one for near distance dispersion, were developed and used to calculate atmospheric dust concentrations at the subject air samplers. Atmospheric 239 Pu impacts were then determined from measurements of plutonium concentrations in the resuspendible dust on the road surfaces. As a final step in the process the calculated plutonium impacts were compared to the 1980 annual average 239 Pu concentration at four samplers. The impact calculated for the Gunnery Range Road represented 2.1 percent of the observed annual concentration, with a 95 percent confidence interval of 1.1 to 7.9 percent. The Southeast Perimeter Road produced a more substantial effect with a point estimate of 3.8 percent. The 95 percent confidence interval for this source was 2.0 to 9.1 percent. The combined impact of the two roads on the subject samplers was 5.9 percent of the observed plutonium concentration, with a 95 percent confidence interval of 3.2 to 17.0 percent. Thus it was shown that fugitive plutonium emissions from the Gunnery Range Road and Southeast Perimeter Road are not substantial contributors to the plutonium concentrations observed at the subject samplers. Even an increase in dust control efficiency to 90 percent (as with paving) would result in only a four percent decrease in the overall atmosperic plutonium concentration at the site

  14. PSF interlaboratory comparison

    International Nuclear Information System (INIS)

    Kellogg, L.S.; Lippincott, E.P.

    1982-01-01

    Two experiments for interlaboratory verification of radiometric analysis methods have been conducted with dosimeters irradiated in the Oak Ridge Research Reactor (ORR) Poolside Facility (PSF) Surveillance Dosimeter Measurement Facility (SDMF). In a preliminary analysis of data supplied by the six participants, biases as large as 60% were observed which could lead to errors of this general magnitude in reported surveillance capsule fluence values. As a result of these comparisons, problems were identified and the spread in final values was greatly reduced. Relative agreement among the final results reported by four of the laboratories now appears to be satisfactory (the non-fission dosimeter results generally falling within +-5% and the fission dosimeter results within +-10%), but improvement is required in order to routinely meet Reactor Vessel Material Surveillance Program goals

  15. CCM key comparison CCM.D-K4 'Hydrometer'

    Science.gov (United States)

    Lorefice, S.; Becerra, L. O.; Lenard, E.; Lee, Y. J.; Lee, W. G.; Madec, T.; Meury, P. A.; Caceres, J.; Santos, C.; Vamossy, C.; Man, J.; Fen, K.; Toda, K.; Wright, J.; Bettin, H.; Toth, H.

    2016-01-01

    This report presents the comparison philosophy, methodology, analysis and the results of the designed CCM.D-K4 key comparison that covered the calibration of high resolution hydrometers for liquid and alcoholometers in the density range 600 kg/m3 to 2000 kg/m3 at the temperature of 20°C. The main purpose of this comparison was not only to evaluate the degree of equivalence in the calibration of high accuracy hydrometers between NMI participants, but also to link, were it is possible, the results of previous comparisons to Key Comparison Reference Values (KCRVs) of CCM.D-K4. Eleven NMI laboratories took part in the CCM.D-K4 divided in two groups (petals). With the CCM.D-K4 purpose, two similar sets consisting of three hydrometers for liquid density determinations and an alcoholometer were circulated to the NMI participants as a travelling standard in the time interval from January 2011 to April 2012. Twelve Key Comparison Reference Values (KCRVs) for each petal have been obtained at the density values related to the tested density marks of the transfer standards by the results of participants. The KCRVs and corresponding uncertainties were calculated by the weighted mean in the case of consistent results, otherwise the median was used. The degree of equivalence (DoE) with respect to the corresponding KCRV was determined for each participant and, in this particular comparison, the Weighted Least Squares (WLS) method was used to link the individual DoE of each participant by a continuous function. Significant drift of the transfer standards was not detected. This report also gives instructions on calculating pair-wise degrees of equivalence, with the addition of any information on correlations that may be necessary to estimate more accurately as well as the procedure for linking international comparisons to the CCM.D-K4. Finally an example of linkage to the CCM.D-K4 is given by dealing with the results of the bilateral comparison between INRiM and NMIA, which was

  16. Cosmology Without Finality

    Science.gov (United States)

    Mahootian, F.

    2009-12-01

    The rapid convergence of advancing sensor technology, computational power, and knowledge discovery techniques over the past decade has brought unprecedented volumes of astronomical data together with unprecedented capabilities of data assimilation and analysis. A key result is that a new, data-driven "observational-inductive'' framework for scientific inquiry is taking shape and proving viable. The anticipated rise in data flow and processing power will have profound effects, e.g., confirmations and disconfirmations of existing theoretical claims both for and against the big bang model. But beyond enabling new discoveries can new data-driven frameworks of scientific inquiry reshape the epistemic ideals of science? The history of physics offers a comparison. The Bohr-Einstein debate over the "completeness'' of quantum mechanics centered on a question of ideals: what counts as science? We briefly examine lessons from that episode and pose questions about their applicability to cosmology. If the history of 20th century physics is any indication, the abandonment of absolutes (e.g., space, time, simultaneity, continuity, determinacy) can produce fundamental changes in understanding. The classical ideal of science, operative in both physics and cosmology, descends from the European Enlightenment. This ideal has for over 200 years guided science to seek the ultimate order of nature, to pursue the absolute theory, the "theory of everything.'' But now that we have new models of scientific inquiry powered by new technologies and driven more by data than by theory, it is time, finally, to relinquish dreams of a "final'' theory.

  17. International comparison of AC-DC current transfer standards

    Science.gov (United States)

    Heine, G.; Garcocz, M.; Waldmann, W.

    2017-01-01

    The measurements of the international comparison of ac-dc current transfer standards identified as EURAMET.EM-K12 started in June 2012 and were completed in December 2014. Twenty NMIs in the EURAMET region and one NMI in the AFRIMET region took part: BEV (Austria), CMI (Czech Republic), PTB (Germany), METAS (Switzerland), JV (Norway), UME (Turkey), GUM (Poland), IPQ (Portugal), CEM (Spain), INRIM (Italy), SP (Sweden), DANIAmet-MI-Trescal (Denmark), BIM (Bulgaria), MKEH (Hungary), SIQ (Slovenia), LNE (France), NSAI NML (Ireland), VSL (The Netherlands), NPL (United Kingdom), Metrosert (Estonia), NIS (Egypt). The comparison was proposed to link the National Metrology Institutes organised in EURAMET to the key comparison CCEM-K12. The ac-dc current transfer difference of each travelling standard had been measured at its nominal current 10 mA and 5 A at the following frequencies: 10 Hz, 55 Hz, 1 kHz, 10 kHz, 20 kHz, 50 kHz, 100 kHz. The test points were selected to link the results with the equivalent CCEM Key Comparison (CCEM-K12), through five NMIs participating in both EURAMET and CCEM key comparisons (PTB, JV, NPL, SP and BEV). The report shows the degree of equivalence in the EURAMET region and also the degree of equivalence with the corresponding CCEM reference value. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

  18. Comparison on the calibrations of hydrometers for liquids density determination between SIM laboratories

    Science.gov (United States)

    Morales, Abed; Quiroga, Aldo; Daued, Arturo; Cantero, Diana; Sequeira, Francisco; Castro, Luis Carlos; Becerra, Luis Omar; Salazar, Manuel; Vega, Maria

    2017-01-01

    A supplementary comparison was made between SIM laboratories concerning the calibration of four hydrometers within the range of 600 kg/m3 to 2000 kg/m3. The main objectives of the comparison were to evaluate the degree of equivalences SIM NMIs in the calibration of hydrometers of high accuracy. The participant NMIs were: CENAM, IBMETRO, INEN, INDECOPI, INM, INTN and LACOMET. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

  19. Bilateral comparison of 1 Ω and 10 kΩ standards (ongoing BIPM key comparisons BIPM.EM-K13.a and 13.b) between the NSAI NML (Ireland) and the BIPM

    Science.gov (United States)

    Rolland, B.; Fletcher, N.; Power, O.

    2017-01-01

    This report gives the result of a bilateral comparison of resistance between the NSAI NML (Ireland) and the BIPM carried out in 2014-2015. Two 1 Ω and two 10 kΩ travelling standards belonging to the BIPM were used. The comparison was carried out with an 'A-B-A' pattern of measurements; the standards were measured first at the BIPM for a period of about one month, then for a similar period at the NSAI-NML, and finally again at the BIPM. The measurand was the 4 terminal dc resistance at low power. The BIPM was the pilot laboratory, and the comparison forms part of the ongoing BIPM key comparisons BIPM.EM-K13.a (for 1 Ω) and BIPM.EM-K13b (for 10 kΩ). The results from the NSAI NML and the BIPM were found to be in good agreement, with a difference smaller than the relative expanded uncertainties (95% confidence, k = 2) of 0.16 × 10-6 for 1 Ω and 0.42 × 10-6 for 10 kΩ. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

  20. Salt Block I test: experimental details and comparison with theory. Final report

    International Nuclear Information System (INIS)

    Duffey, T.A.

    1980-02-01

    A series of laboratory experiments has been completed at Sandia Laboratories to provide an understanding of the steady state and transient thermal response of a large salt block containing an internal heat source. In this report, details of the experimental program are presented along with results of related efforts, such as thermal conductivity experiments, done in support of the heater experiments (Salt Block I). Finite element temperature field predictions, both transient and steady state, are performed utilizing the COYOTE nonlinear heat conduction program. Comparisons of experimental and theoretical results are generally quite good

  1. Comparison of measurement capability with 100 μmol/mol of carbon monoxide in nitrogen

    Science.gov (United States)

    Lee, Jeongsoon; Lee, JinBok; Lim, Jeongsik; Tarhan, Tanıl; Liu, Hsin-Wang; Aggarwal, Shankar G.

    2018-01-01

    Carbon monoxide (CO) in nitrogen was one of the first types of gas mixtures used in an international key comparison. The comparison dates back to 1998 (CCQMK1a) [1]. Since then, many National Metrology Institutes (NMIs) have developed calibration and measurement capabilities (CMCs) for these mixtures. Recently, NMIs in the APMP region have actively participated in international comparisons to provide domestic services. At the 2013 APMP meeting, several NMIs requested a CO comparison to establish CO/N2 certification for industrial applications, which was to be coordinated by KRISS. Consequently, this comparison provides an opportunity for APMP regional NMIs to develop CO/N2 CMC claims. The goal of this supplementary comparison is to support CMC claim for carbon monoxide in the N2 range of 50–2000 μmol/mol. An extended range may be supported as described in the GAWG strategy for comparisons and CMC claims. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

  2. Modelling multi-phase liquid-sediment scour and resuspension induced by rapid flows using Smoothed Particle Hydrodynamics (SPH) accelerated with a Graphics Processing Unit (GPU)

    Science.gov (United States)

    Fourtakas, G.; Rogers, B. D.

    2016-06-01

    A two-phase numerical model using Smoothed Particle Hydrodynamics (SPH) is applied to two-phase liquid-sediments flows. The absence of a mesh in SPH is ideal for interfacial and highly non-linear flows with changing fragmentation of the interface, mixing and resuspension. The rheology of sediment induced under rapid flows undergoes several states which are only partially described by previous research in SPH. This paper attempts to bridge the gap between the geotechnics, non-Newtonian and Newtonian flows by proposing a model that combines the yielding, shear and suspension layer which are needed to predict accurately the global erosion phenomena, from a hydrodynamics prospective. The numerical SPH scheme is based on the explicit treatment of both phases using Newtonian and the non-Newtonian Bingham-type Herschel-Bulkley-Papanastasiou constitutive model. This is supplemented by the Drucker-Prager yield criterion to predict the onset of yielding of the sediment surface and a concentration suspension model. The multi-phase model has been compared with experimental and 2-D reference numerical models for scour following a dry-bed dam break yielding satisfactory results and improvements over well-known SPH multi-phase models. With 3-D simulations requiring a large number of particles, the code is accelerated with a graphics processing unit (GPU) in the open-source DualSPHysics code. The implementation and optimisation of the code achieved a speed up of x58 over an optimised single thread serial code. A 3-D dam break over a non-cohesive erodible bed simulation with over 4 million particles yields close agreement with experimental scour and water surface profiles.

  3. Subsequent bilateral comparison to CCT-K3, CIPM key comparison CCT-K3.1: Comparison of standard platinum resistance thermometers at the triple point of water (T = 273.16 K) and at the melting point of gallium (T = 302.9146 K)

    Science.gov (United States)

    Picard, S.; Nonis, M.; Solve, S.; Allisy-Roberts, P. J.; Renaot, E.; Martin, C.

    2011-01-01

    A comparison of standard platinum resistance thermometers (SPRTs) has been carried out between the BIPM and the Laboratoire commun de métrologie LNE-CNAM using the melting point of gallium and the triple point of water. The temperature difference at Ga between the BIPM and the LNE-CNAM was determined as 108 µK with an associated combined standard uncertainty of 223 µK. This outcome indicates a present temperature difference of the BIPM of -65 µK with respect to an Average Reference Value from an earlier comparison, with an associated uncertainty of uc = 262 µK. It should be noted that the present BIPM scale is not independent, but traceable to cells used in KC7. The comparison results validate the re-establishment of thermometer calibrations at the BIPM for internal use. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCT, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

  4. Comparison of neutron spectrum unfolding codes

    International Nuclear Information System (INIS)

    Zijp, W.

    1979-02-01

    This final report contains a set of four ECN-reports. The first is dealing with the comparison of the neutron spectrum unfolding codes CRYSTAL BALL, RFSP-JUL, SAND II and STAY'SL. The other three present the results of calculations about the influence of statistical weights in CRYSTAL BALL, SAND II and RFSP-JUL

  5. Results of the EURAMET.RI(II)-S6.I-129 supplementary comparison

    Science.gov (United States)

    García-Toraño, Eduardo; Altzitzoglou, Timotheos; Auerbach, Pavel; Bé, Marie-Martine; Lourenço, Valérie; Bobin, Christophe; Cassette, Philippe; Dersch, Rainer; Kossert, Karsten; Nähle, Ole; Peyrés, Virginia; Pommé, Stefaan; Rozkov, Andrej; Sanchez-Cabezudo, Anabel; Sochoro&vacute; , Jana

    2015-01-01

    An international comparison of the long-lived gamma-ray emitter 129I has been recently completed. A total of 5 laboratories measured a solution prepared by Centro de Investigaciones Energéticas, Medioambientales y Tecnológicas (CIEMAT). Aliquots of the master solution were standardized in terms of activity per mass unit by participant laboratories using 4 different techniques. The results of the comparison can be used as the basis for establishing the equivalence among the laboratories. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCRI, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

  6. Bilateral comparison of 10 V standards between the NSAI-NML (Ireland) and the BIPM, February to March 2012 (part of the ongoing BIPM key comparison BIPM.EM-K11.b)

    Science.gov (United States)

    Power, O.; Solve, S.; Chayramy, R.; Stock, M.

    2012-01-01

    As part of the on-going BIPM key comparison BIPM.EM-K11.b, a comparison of the 10 V voltage reference standards of the BIPM and the National Standards Authority of Ireland-National Metrology Laboratory (NSAI-NML), Dublin, Ireland, was carried out from February to March 2012. Two BIPM Zener diode-based travelling standards (Fluke 732B), BIPM_C (ZC) and BIPM_D (ZD), were transported by freight to NSAI-NML. At NSAI-NML, the reference standard for DC voltage at the 10 V level consists of a group of characterized Zener diode-based electronic voltage standards. The output EMF (electromotive force) of each travelling standard was measured by direct comparison with the group standard. At the BIPM the travelling standards were calibrated, before and after the measurements at NSAI-NML, with the Josephson voltage standard. Results of all measurements were corrected for the dependence of the output voltages on internal temperature and ambient atmospheric pressure. The final result of the comparison is presented as the difference between the value assigned to DC voltage standard by NSAI-NML, at the level of 10 V, at NSAI-NML, UNML, and that assigned by the BIPM, at the BIPM, UBIPM, at the reference date of 23 February 2012. UNML - UBIPM = +0.83 µV, uc = 1.35 µV, at 10 V where uc is the combined standard uncertainty associated with the measured difference, including the uncertainty of the representation of the volt at the BIPM and at NSAI-NML, based on KJ-90, and the uncertainty related to the comparison. The final result is impacted by the anomalous offset between the NSAI-NML results for the two transfer standards. The reason for this offset hasn't been determined. However, the difference remains within the total combined standard uncertainty. Therefore, the comparison result shows that the voltage standards maintained by NSAI-NML and the BIPM were equivalent, within their stated expanded uncertainties, on the mean date of the comparison. Main text. To reach the main text of

  7. Development of quality control system for fingerprint comparison processes

    Directory of Open Access Journals (Sweden)

    Shiquan Liu

    2017-01-01

    Full Text Available Fingerprint evidence played an important role in investigation, prosecution, and trial process due to the belief of its uniqueness and unchanged characteristics. However, in recent years, the science behind the process of fingerprint comparisons has been questioned. Main research questions have been focusing on the opaqueness within the comparison processes, subjective judgments, lack of universal standards, no error rate expression on final conclusions, and poor scientific fundamental research data. Facing the above-mentioned questions, this paper aims to suggest a quality control system (QCS for fingerprint comparison processes. This QCS is based on the use of software (PiAnoS and its technological features, being able to provide a data management model to increase the transparency and quality of fingerprint comparison processes.

  8. Plutonium-aerosol emission rates and human pulmonary deposition calculations for Nuclear Site 201, Nevada Test Site

    International Nuclear Information System (INIS)

    Shinn, J.H.; Homan, D.N.

    1982-01-01

    This study determined the plutonium-aerosol fluxes from the soil to quantify (1) the extent of potential human exposure by deep-lung retention of alpha-emitting particles; (2) the source term should there be any significant, long-term, transport of plutonium aerosols; and (3) the resuspension factor and rate so that, for the first time at any nuclear site, one may calculate how long it will take for wind erosion to carry away a significant amount of the contaminated soil. High-volume air samplers and cascade impactors were used to characterize the plutonium aerosols. Meteorological flux-profile methods were used to calculate dust and plutonium aerosol emission rates. A floorless wind tunnel (10-m long) was used to examine resuspension under steady-state, high wind speed. The resuspension factor was two orders of magnitude lower than the other comparable sites at NTS and elsewhere, and the average resuspension rate of 5.3 x 10 -8 /d was also very low, so that the half-time for resuspension by wind erosion was about 36,000 y

  9. The comparison of available data on PWR assembly thermal behavior with analytical predictions. Topical report (final)

    International Nuclear Information System (INIS)

    Liu, J.; Todreas, N.

    1979-02-01

    The comparison of available data with analytical predictions has been illustrated in this report. Since few data on the cross flow are available, a study of parameters in the transverse momentum equation was performed to assess the sensitivity of results to their assumed values. It is confirmed that effects of these parameters on the overall results are not significant under PWR operating conditions. Data on subchannel properties of quality and mass flux were also assessed. From the data comparisons, it is evident that COBRA can successfully predict the PWR normal operating conditions but cannot predict the trend under bulk quality conditions

  10. Sediment dynamics in a large shallow lake characterized by seasonal flood pulse in Southeast Asia.

    Science.gov (United States)

    Siev, Sokly; Yang, Heejun; Sok, Ty; Uk, Sovannara; Song, Layheang; Kodikara, Dilini; Oeurng, Chantha; Hul, Seingheng; Yoshimura, Chihiro

    2018-08-01

    Most of studies on sediment dynamics in stable shallow lakes focused on the resuspension process as it is the dominant process. However, understanding of sediment dynamics in a shallow lake influenced by flood pulse is unclear. We tested a hypothesis that floodplain vegetation plays as a significant role in lessening the intensity of resuspension process in a shallow lake characterized by the flood pulse system. Therefore, this study aimed to investigate sediment dynamics in this type of shallow lake. The target was Tonle Sap Lake (TSL), which is a large shallow lake influenced by a flood pulse system of Mekong River located in Southeast Asia. An extensive and seasonal sampling survey was conducted to measure total suspended solid (TSS) concentrations, sedimentation and resuspension rates in TSL and its 4 floodplain areas. The study revealed that sedimentation process was dominant (TSS ranged: 3-126mgL -1 ) in the high water period (September-December) while resuspension process was dominant (TSS ranged: 4-652mgL -1 ) only in the low water period (March-June). In addition, floodplain vegetation reduced the resuspension of sediment (up to 26.3%) in water. The implication of the study showed that resuspension is a seasonally dominant process in shallow lake influenced by the flood pulse system at least for the case of TSL. Copyright © 2018 Elsevier B.V. All rights reserved.

  11. Final report on CCQM-P151: Halocarbons in dry whole air

    Science.gov (United States)

    Rhoderick, George; Guenther, Franklin; Duewer, David; Lee, Jeongsoon; Seog Kim, Jin; Hall, Bradley; Weiss, Ray; Harth, Christina; Reimann, Stefan; Vollmer, Martin

    2014-01-01

    The growing awareness of climate change/global warming and continuing concerns regarding stratospheric ozone depletion will require future measurements and standards for many compounds, in particular halocarbons that are linked to these issues. In order to track and control the emissions of these species globally in the atmosphere, it is necessary to demonstrate measurement equivalence at the highest levels of accuracy for assigned values of standards. This report describes the results of a pilot study between National Metrology Institutes and atmospheric research laboratories for several of the more important halocarbons at atmospheric concentration levels. The comparison includes the chlorofluorocarbons (CFCs) dichlorodifluoromethane (CFC 12), trichlorofluoromethane (CFC 11), and 1,1,2-trichlorotrifluoroethane (CFC 113); the hydrochlorofluorocarbons (HCFCs) chlorodifluoromethane (HCFC 22) and 1-chloro-1,1-difluoroethane (HCFC 142b); and the hydrofluorocarbon (HFC) 1,1,1,2-tetrafluoroethane (HFC 134a), all in a dried whole air sample. The objective of this key comparison is to compare the measurement capabilities of the participants for these halocarbons at trace atmospheric levels. Main text. To reach the main text of this paper, click on Final Report. The final report has been peer-reviewed and approved for publication by the CCQM.

  12. Comparison of tree types of models for the prediction of final academic achievement

    Directory of Open Access Journals (Sweden)

    Silvana Gasar

    2002-12-01

    Full Text Available For efficient prevention of inappropriate secondary school choices and by that academic failure, school counselors need a tool for the prediction of individual pupil's final academic achievements. Using data mining techniques on pupils' data base and expert modeling, we developed several models for the prediction of final academic achievement in an individual high school educational program. For data mining, we used statistical analyses, clustering and two machine learning methods: developing classification decision trees and hierarchical decision models. Using an expert system shell DEX, an expert system, based on a hierarchical multi-attribute decision model, was developed manually. All the models were validated and evaluated from the viewpoint of their applicability. The predictive accuracy of DEX models and decision trees was equal and very satisfying, as it reached the predictive accuracy of an experienced counselor. With respect on the efficiency and difficulties in developing models, and relatively rapid changing of our education system, we propose that decision trees are used in further development of predictive models.

  13. Comparison of biometric predictability and final refraction expected in phacoemulsification surgery with and without trabeculectomy

    Directory of Open Access Journals (Sweden)

    Fernanda Guedes Oliveira

    Full Text Available Abstract Objective: The main purpose of this article is to compare the predictability of biometric results and final refractive outcomes expected in patients undergoing cataract surgery through phacoemulsification with and without associated trabeculectomy. Methods: Cataract patients who have undergone phacoemulsification surgery alone (control group or associated with trabeculectomy (study group screened. All surgeries were performed following standard protocol. For enrollment, biometrics calculated by IOL Master (Carl Zeiss Meditec, Inc. biometry, refraction and intraocular pressure (IOP before and after surgery were required. Data was compared between groups in addition to the correlation between variation of IOP and final refraction. Results: Thirty eyes per group were enrolled. Only prior IOP (p <0.001, IOP post-surgery (p = 0.01 and the difference in IOP (p <0.001 were statistically significant. Axial length, IOL diopter used, expected spherical refraction by biometrics and astigmatism pre- and post-surgery were similar in both groups (p=0.1; 0.4; 0.4; 0.5 and 0.3, respectively. Spherical predictability by biometrics within 0.25 diopters was noted in both the control group (range 0.06 ± 0.45 and study group (range 0.25 ± 0.97, p = 0.3. There was no statistical significance between groups for the difference between final cylinder and corneal astigmatism (p = 0.9, and the difference between axis of refractive and corneal astigmatism (p = 0.7. Conclusion: The biometric predictability in phacoemulsification surgery and the expected final refraction are significant, andare not modified by trabeculectomy in the combined surgeries.

  14. Behind the Final Grade in Hybrid v. Traditional Courses: Comparing Student Performance by Assessment Type, Core Competency, and Course Objective

    Science.gov (United States)

    Bain, Lisa Z.

    2012-01-01

    There are many different delivery methods used by institutions of higher education. These include traditional, hybrid, and online course offerings. The comparisons of these typically use final grade as the measure of student performance. This research study looks behind the final grade and compares student performance by assessment type, core…

  15. Bilateral comparison of 10 V standards between the NSAI-NML (Ireland) and the BIPM, March 2014 (part of the ongoing BIPM key comparison BIPM.EM-K11.b)

    Science.gov (United States)

    Solve, S.; Chayramy, R.; Power, O.; Stock, M.

    2014-01-01

    As part of the ongoing BIPM key comparison BIPM.EM-K11.b, a comparison of the 10 V voltage reference standards of the BIPM and the National Standards Authority of Ireland-National Metrology Laboratory (NSAI-NML), Dublin, Ireland, was carried out in February and March 2014. Two BIPM Zener diode-based travelling standards (Fluke 732B), BIPM_4 (Z4) and BIPM_5 (Z5), were transported by freight to NSAI-NML. At NSAI-NML, the reference standard for DC voltage at the 10 V level consists of a group of characterized Zener diode-based electronic voltage standards. The output EMF (Electromotive Force) of each travelling standard was measured by direct comparison with the group standard. At the BIPM the travelling standards were calibrated, before and after the measurements at NSAI-NML, with the Josephson Voltage Standard. Results of all measurements were corrected for the dependence of the output voltages of the Zener standards on internal temperature and ambient atmospheric pressure. The final result of the comparison is presented as the difference between the value assigned to DC voltage standard by NSAI-NML, at the level of 10 V, at NSAI-NML, UNML, and that assigned by the BIPM, at the BIPM, UBIPM, at the reference date of 10 March 2014. UNML - UBIPM = -0.64 µV uc = 1.35 µV, at 10 V where uc is thecombined standard uncertainty associated with the measured difference, including the uncertainty of the representation of the volt at the BIPM and at NSAI-NML,based on KJ-90, and the uncertainty related to the comparison. The comparison results show that the voltage standards maintained by NSAI-NML and the BIPM were equivalent, within their stated standard uncertainties, on the mean date of the comparison. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to

  16. Transmission of radioiodine through sampling lines

    International Nuclear Information System (INIS)

    Unrein, P.J.; Pelletier, C.A.; Cline, J.E.; Voilleque, P.G.

    1985-01-01

    An experimental program to measure radioiodine transmission through sampling lines is described. The transmission depends upon both deposition on and resuspension from the walls of the line. The deposition and resuspension processes are themselves controlled by the length, diameter, and material of the line and the conditions under which it is operated. The operating conditions under study are sampling flow rate, temperature and relative humidity. Measurement results have been interpreted in terms of a four-compartment model of radioiodine deposition and resuspension. The model is applied to each of twenty or more segments of the line. Experimental measurements of short-term transmission fractions and the deposition velocities derived from them are presented for six lines. Data on resuspension rates for the same lines were obtained and are also discussed

  17. Soil surface stabilization using an in situ plutonium coating techniuqe at the Nevada Test Site

    International Nuclear Information System (INIS)

    Lew, J.; Snipes, R.; Tamura, T.

    1996-01-01

    The Hazardous Waste Remedial Actions Program (HAZWRAP), in collaboration with the University of Nevada at Reno (UNR), has developed and is investigating an in situ plutonium treatment for soils at the Nevada Test Site (NTS). The concept, conceived by Dr. T. Tamura and refined at HAZWRAP, was developed during the Nevada Applied Ecology Program investigation. In analyzing for plutonium in soils, it was noted that the alpha emanation of plutonium was greatly attenuated if traces of iron or manganese oxides were present in the final electroplating stage. The technique would reduce resuspension of alpha particles into the air by coating the contaminants in soils in situ with an environmentally compatible, durable, and nontoxic material. The coating materials (calcium hydroxide, ferrous sulfate) reduce resuspension by providing a cementitious barrier against radiation penetration while retaining soil porosity. This technique not only stabilizes plutonium-contaminated soils, but also provides an additional protection from worker exposure to radiation during remediation activities. Additionally, the coating would decrease the water solubility of the contaminant and, thus, reduce its migration through soil and uptake by plants

  18. International comparison CCQM-K119 liquefied petroleum gas

    Science.gov (United States)

    Brewer, P. J.; Downey, M. L.; Atkins, E.; Brown, R. J. C.; Brown, A. S.; Zalewska, E. T.; van der Veen, A. M. H.; Smeulders, D. E.; McCallum, J. B.; Satumba, R. T.; Kim, Y. D.; Kang, N.; Bae, H. K.; Woo, J. C.; Konopelko, L. A.; Popova, T. A.; Meshkov, A. V.; Efremova, O. V.; Kustikov, Y.

    2018-01-01

    Liquefied hydrocarbon mixtures with traceable composition are required in order to underpin measurements of the composition and other physical properties of LPG (liquefied petroleum gas), thus meeting the needs of an increasingly large industrial market. This comparison aims to assess the analytical capabilities of laboratories for measuring the composition of a Liquid Petroleum Gas (LPG) mixture when sampled in the liquid phase from a Constant Pressure Cylinder. Mixtures contained ethane, propane, propene, i-butane, n-butane, but-1-ene and i-pentane with nominal amount fractions of 2, 71, 9, 4, 10, 3 and 1 cmol mol-1 respectively. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

  19. Examination of the pathways from soil to man for plutonium

    International Nuclear Information System (INIS)

    Healy, J.W.

    1977-04-01

    The data available on resuspension and ingestion as pathways of plutonium from soil to man were reviewed and a recommended limit based upon a conservative interpretation of the National Council on Radiation Protection and Measurements (NCRP) recommendations for limiting values was derived. Wind resuspension appeared to be the least limiting value with mechanical resuspension and pica in children among the more important. Ingestion of foodstuffs could also be an important pathway if it is assumed that all food is produced in the contaminated area

  20. Properties of hadronic final states in diffractive deep inelastic ep scattering at DESY HERA

    International Nuclear Information System (INIS)

    2002-01-01

    Characteristics of the hadronic final state of diffractive deep inelastic scattering events ep→eXp were studied in the kinematic range 4 X 2 2 , 70 P <0.03 with the ZEUS detector at the DESY ep collider HERA using an integrated luminosity of 13.8 pb-1. The events were tagged by identifying the diffractively scattered proton using the leading proton spectrometer. The properties of the hadronic final state X were studied in its center-of-mass frame using thrust, thrust angle, sphericity, energy flow, transverse energy flow, and 'seagull' distributions. As the invariant mass of the system increases, the final state becomes more collimated, more aligned, and more asymmetric in the average transverse momentum with respect to the direction of the virtual photon. Comparisons of the properties of the hadronic final state with predictions from various Monte Carlo model generators suggest that the final state is dominated by qq-barg states at the parton level

  1. Bilateral comparison of 10 V standards between the NSAI-NML (Ireland) and the BIPM, March to April 2011 (part of the ongoing BIPM key comparison BIPM.EM-K11.b)

    Science.gov (United States)

    Power, O.; Solve, S.; Chayramy, R.; Stock, M.

    2011-01-01

    As a part of the ongoing BIPM key comparison BIPM.EM-K11.b, a comparison of the 10 V voltage reference standards of the BIPM and the National Standards Authority of Ireland-National Metrology Laboratory (NSAI-NML), Dublin, Ireland, was carried out from March to April 2011. Two BIPM Zener diode-based travelling standards (Fluke 732B) were transported by freight to NSAI-NML. At NSAI-NML, the 10 V output EMF of each travelling standard was measured by direct comparison with a group of characterized Zener diode-based electronic voltage standards. At the BIPM, the travelling standards were calibrated before and after the measurements at NSAI-NML, with the Josephson Voltage Standard. Results of all measurements were corrected for the dependence of the output voltages on internal temperature and ambient pressure. The comparison results show that the voltage standards maintained by NSAI-NML and the BIPM were equivalent, within their stated expanded uncertainties, on the mean date of the comparison. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

  2. Bilateral Comparison of 10 V Standards between the NSAI - NML (Ireland) and the BIPM, March 2015 (part of the ongoing BIPM key comparison BIPM.EM-K11.b)

    Science.gov (United States)

    Solve, S.; Chayramy, R.; Stock, M.; Power, O.

    2015-01-01

    As part of the ongoing BIPM key comparison BIPM.EM-K11.b, a comparison of the 10 V voltage reference standards of the BIPM and the National Standards Authority of Ireland - National Metrology Laboratory (NSAI - NML), Dublin, Ireland, was carried out in February and March 2015. Two BIPM Zener diode-based travelling standards (Fluke 732B), BIPM6 (Z6) and BIPMC (ZC), were transported by freight to NSAI-NML. At NSAI-NML, the reference standard for DC voltage at the 10 V level consists of a group of characterized Zener diode-based electronic voltage standards. The output EMF (Electromotive Force) of each travelling standard was measured by direct comparison with the group standard. At the BIPM the travelling standards were calibrated, before and after the measurements at NSAI-NML, with the Josephson Voltage Standard. Results of all measurements were corrected for the dependence of the output voltages of the Zener standards on internal temperature and ambient atmospheric pressure. The final resultof the comparison is presented as the difference between the values assigned to DC voltage standards by NSAI - NML, at the level of 10 V,at NSAI - NML, UNML, and those assigned by the BIPM, at the BIPM, UBIPM, at the reference date of 24 February 2015. UNML - UBIPM = - 0.82 mV; uc = 1.35 mV , at 10 V where uc is the combined standard uncertainty associated with the measured difference, including the uncertainty of the representation of the volt at the BIPM and at NSAI-NML, based on KJ-90, and the uncertainty related to the comparison. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

  3. Bilateral comparison of 10 V standards between the NSAI - NML (Ireland) and the BIPM, February 2016 (part of the ongoing BIPM key comparison BIPM.EM-K11.b)

    Science.gov (United States)

    Solve, S.; Chayramy, R.; Power, O.; Stock, M.

    2016-01-01

    As part of the ongoing BIPM key comparison BIPM.EM-K11.b, a comparison of the 10 V voltage reference standards of the BIPM and the National Standards Authority of Ireland - National Metrology Laboratory (NSAI - NML), Dublin, Ireland, was carried out in January and February 2016. Two BIPM Zener diode-based travelling standards (Fluke 732B), BIPM7 (Z7) and BIPM9 (Z9), were transported by freight to NSAI-NML. At NSAI-NML, the reference standard for DC voltage at the 10 V level consists of a group of characterized Zener diode-based electronic voltage standards. The output EMF (Electromotive Force) of each travelling standard was measured by direct comparison with the group standard. At the BIPM the travelling standards were calibrated, before and after the measurements at NSAI-NML, with the Josephson Voltage Standard. Results of all measurements were corrected for the dependence of the output voltages of the Zener standards on internal temperature and ambient atmospheric pressure. The final result of the comparison is presented as the difference between the values assigned to DC voltage standards by NSAI - NML, at the level of 10 V, at NSAI - NML, UNML, and those assigned by the BIPM, at the BIPM, UBIPM, at the reference date of the 31 of January 2016. UNML - UBIPM = + 0.22 μV uc = 1.35 μV , at 10 V where uc is the combined standard uncertainty associated with the measured difference, including the uncertainty of the representation of the volt at the BIPM and at NSAI-NML, based on KJ-90, and the uncertainty related to the comparison. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

  4. An international comparison of nuclear plant training programs

    International Nuclear Information System (INIS)

    Mason, J.H.

    1993-01-01

    In 1990, I visited four utility companies that own and operate pressurized water reactor (PWR) plants in different countries. The purpose of my visits and associated research was to compare nuclear power plant operator and technician training programs. The companies were: Duke Power Company (DUKE) in the United States, Electricite de France (EDF) in France, Kansai Electric Power Company (KEPCO) in Japan, and RWE Energie AG (RWE) in Germany. The purpose of this paper is to highlight selected aspects of the comparison. First, comparisons of the four subject utilities and four typical nuclear power stations operated by each company, McGuire, Paluel, Ohi, and Biblis, are provided. Then comparisons of new employee demographics and training program specific content are provided. Finally, some general observations are drawn from the comparisons. The comparisons are based on information obtained from documents, interviews, and visits to stations and training centers. However, some interpretation of the information was necessary in order to enable a comparison. For example, categorization of training modules requires judgement, interpretation, and translation. In all cases, the information is intended to be representative or typical, rather than statistically precise

  5. Computation of radionuclide particulate finite area fugitive source strengths

    Energy Technology Data Exchange (ETDEWEB)

    Fields, D E

    1983-06-01

    Atmospheric source strengths quantifying particulate re-suspension from wind and non-wind disturbance-driven processes are computed for sites of small area. These values are useful in computing downwind air concentration values to evaluate risk to exposed populations. The net source strength for the site is the sum of the wind- and disturbance-driven components. A unified source strength approach includes both classes of re-suspension processes. More research is needed to satisfactorily express the time-dependence of re-suspension parameters, especially in non-arid climates where population densities are greater. (JMT)

  6. Report of the key-comparison of spectral diffuse reflectance (EURAMET.PR-K5) (Ref. 619)

    Science.gov (United States)

    Andor, György; Gál, Péter

    2018-01-01

    This report details the final results of the EURAMET comparison on regular spectral transmittance carried out between 2006 and 2016. The aim of this comparison was to check the agreement of measurement of the spectral diffuse reflectance among participants, using the measurement geometry of d/0 or 0/d in the wavelength range of 360 nm to 780 nm at 20 nm increment. We used a star type comparison: first the participants sent their samples to the pilot, than the pilot measured all the samples of the participants and sent them back. The participants measured the samples and sent them to the pilot for control measurement. Six standards were used as reference standards in order to maintain the scale during the comparison. These were three samples of BCR-406 opal glasses (BCR 30506; BCR 30303; BCR 30704), an MC20 Russian opal glass (MC 4777) and two samples made of pressed halon (polytetrafluoroethylene) powder (halon 2007A; halon 2007C). These six samples were designated as the Comparison reference standards. The diffuse reflectance was initially measured on the OMH (BFKH) absolute reflectometer. The link to the CCPR-K5 results was BFKH, and the check on BFKH was the PTB results who also participated in the CCPR-K5 comparison. The participants were GUM, INM, LNE, METAS, BFKH, PTB, SP. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCPR, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

  7. Bilateral comparison of 10 V standards between the NSAI-NML (Ireland) and the BIPM, January to February 2013 (part of the ongoing BIPM key comparison BIPM.EM-K11.b)

    Science.gov (United States)

    Power, O.; Chayramy, R.; Solve, S.; Stock, M.

    2014-01-01

    As part of the ongoing BIPM key comparison BIPM.EM-K11.b, a comparison of the 10 V voltage reference standards of the BIPM and the National Standards Authority of Ireland-National Metrology Laboratory (NSAI-NML), Dublin, Ireland, was carried out from January to February 2013. Two BIPM Zener diode-based travelling standards (Fluke 732B), BIPM_8 (Z8) and BIPM_9 (Z9), were transported by freight to NSAI-NML. At NSAI-NML, the reference standard for DC voltage at the 10 V level consists of a group of characterized Zener diode-based electronic voltage standards. The output EMF (electromotive force) of each travelling standard was measured by direct comparison with the group standard. At the BIPM the travelling standards were calibrated, before and after the measurements at NSAI-NML, with the Josephson Voltage Standard. Results of all measurements were corrected for the dependence of the output voltages of the Zener standards on internal temperature and ambient atmospheric pressure. The final result of the comparison is presented as the difference between the value assigned to DC voltage standard by NSAI-NML, at the level of 10 V, at NSAI-NML, UNML, and that assigned by the BIPM, at the BIPM, UBIPM, at the reference date of 5 February 2013. UNML - UBIPM = -0.63 µV uc = 1.31 µV, at 10 V where uc is thecombined standard uncertainty associated with the measured difference, including the uncertainty of the representation of the volt at the BIPM and at NSAI-NML,based on KJ-90, and the uncertainty related to the comparison. The comparison results show that the voltage standards maintained by NSAI-NML and the BIPM were equivalent, within their stated standard uncertainties, on the mean date of the comparison. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according

  8. Final report on RMO key comparison EURAMET.L-K6: CMM 2-D artifact: ball plate

    DEFF Research Database (Denmark)

    Jusko, O.; Banreti, E.; Bergmans, R.

    2013-01-01

    An industrial standard steel ball plate of dimension 420 mm with 25 ceramic balls in a 5 × 5 arrangement was circulated among 12 European NMIs. The measurement task was the calibration of the centres of the 25 balls. The measurements were conducted between 2004 and 2006. One NMI withdrew from...... the comparison. The other 11 NMIs measured the ball plate and delivered data. The artifact was found to be stable during the duration of the comparison. For the analysis both the deviations from the KCRV and the En numbers were calculated. Most results agreed very well within the claimed uncertainty. A few...... for publication by the CCL, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA)....

  9. Emissions of road dust by winter tyres and the contributions of different road dust sources in road side particle samples; Talvirenkaiden poelypaeaestoet ja eri katupoelylaehteiden osuudet kadunvarrella keraetyissae hiukkasnaeytteissae

    Energy Technology Data Exchange (ETDEWEB)

    Kupiainen, K.; Pirjola, L.; Ritola, R.; Stojiljkovic, A.; Malinen, A.

    2013-09-01

    Aim of this study was to determine: (1) the relative contributions from pavement wear and traction sanding in PM{sub 10} road side air and road dust resuspension samples; (2) PM{sub 10} dust emissions from studded and studless tyres in on-road conditions. The study was conducted as part of the NASTA research program during the winter season 2011/2012. The studies were carried out in Suurmetsaentie and Viikintie in Helsinki, Finland. The results showed that dust from pavement aggregates was the largest source during spring, accounting for 40- 50 percent of the particulate matter in the air and resuspension samples. Based on studies on formation of dust, major source of the dust from pavement aggregates is the wear by studded tyres. Traction sand and road salt were used frequently during the winter 2011/2012. Sanding material explained about 25 percent of the road dust in the air and resuspension samples. Traction sanding is estimated to account for approximately few percent of the pavement dust via the sandpaper effect. Effect of road salt was few percent in the samples. The source contributions from pavement and traction sanding observed in spring 2011/2012 at Suurmetsaentie are similar to what has been estimated in previous studies conducted in the early 2000s in Finland. In a study conducted in the city of Hanko, it was estimated the contribution from traction sanding to be in average of about 10 percent. In another study in the center of Helsinki the contribution was estimated to be about half of the PM{sub 10}. The general perception in Finland has been that traction sanding is the main source of airborne road dust. Studies conducted in 2000s and the results of this study, however, indicate that traction sanding has been an important but not the main source of PM10 road dust even in winters with extensive use of gravel for traction control. Emissions of road dust by a single tyre consist of direct emissions of wear products as well as resuspension emissions of

  10. KEY COMPARISON Bilateral comparison of 1.018 V and 10 V standards between the NSAI-NML (Ireland) and the BIPM, March to April 2010 (part of the ongoing BIPM key comparison BIPM.EM-K11.a and b)

    Science.gov (United States)

    Power, O.; Solve, S.; Chayramy, R.; Stock, M.

    2010-01-01

    As a part of the ongoing BIPM key comparisons BIPM.EM-K11.a and b, a comparison of the 1.018 V and 10 V voltage reference standards of the BIPM and of the National Standards Authority of Ireland-National Metrology Laboratory (NSAI-NML), Dublin, Ireland, was carried out from March to April 2010. Two BIPM Zener diode-based travelling standards were transported by freight to NSAI-NML. At NSAI-NML, the reference standard for DC voltage is maintained at the 10 V level by means of a group of characterized Zener diode-based electronic voltage standards. The output EMF of each travelling standard, at the 10 V output terminals, was measured by direct comparison with the group standard. Measurements of the output EMF of the travelling standards at the 1.018 V output terminals were made using a potentiometer, standardized against the local 10 V reference standard. At the BIPM, the travelling standards were calibrated at both voltages before and after the measurements at NSAI-NML, using the BIPM Josephson Voltage Standard. Results of all measurements were corrected for the dependence of the output voltages on internal temperature and ambient pressure. The comparison results show that the voltage standards maintained by NSAI-NML and the BIPM were equivalent, within their stated expanded uncertainties, on the mean date of the comparison. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

  11. Immediacy bias in social-emotional comparisons.

    Science.gov (United States)

    White, Katherine; Van Boven, Leaf

    2012-08-01

    In seven studies of naturally occurring, "real-world" emotional events, people demonstrated an immediacy bias in social-emotional comparisons, perceiving their own current or recent emotional reactions as more intense compared with others' emotional reactions to the same events. The events examined include crossing a scary bridge (study 1a), a national tragedy (study 1b), terrorist attacks (studies 2a and 3b), a natural disaster (study 2b), and a presidential election (study 3b). These perceived differences between one's own and others' emotions declined over time, as relatively immediate and recent emotions subsided, a pattern that people were not intuitively aware of (study 2c). This immediacy bias in social-emotional comparisons emerged for both explicit comparisons (studies 1a, 1b, and 3b), and for absolute judgments of emotional intensity (studies 2a, 2b, and 3a). Finally, the immediacy bias in social-emotional comparisons was reduced when people were reminded that emotional display norms might lead others' appearances to understate emotional intensity (studies 3a and 3b). Implications of these findings for social-emotional phenomena are discussed.

  12. Spatially explicit feedbacks between seagrass meadow structure, sediment and light: Habitat suitability for seagrass growth

    Science.gov (United States)

    Carr, Joel; D'Odorico, Paul; McGlathery, Karen; Wiberg, Patricia L.

    2016-01-01

    In shallow coastal bays where nutrient loading and riverine inputs are low, turbidity, and the consequent light environment are controlled by resuspension of bed sediments due to wind-waves and tidal currents. High sediment resuspension and low light environments can limit benthic primary productivity; however, both currents and waves are affected by the presence of benthic plants such as seagrass. This feedback between the presence of benthic primary producers such as seagrass and the consequent light environment has been predicted to induce bistable dynamics locally. However, these vegetated areas influence a larger area than they footprint, including a barren adjacent downstream area which exhibits reduced shear stresses. Here we explore through modeling how the patchy structure of seagrass meadows on a landscape may affect sediment resuspension and the consequent light environment due to the presence of this sheltered region. Heterogeneous vegetation covers comprising a mosaic of randomly distributed patches were generated to investigate the effect of patch modified hydrodynamics. Actual cover of vegetation on the landscape was used to facilitate comparisons across landscape realizations. Hourly wave and current shear stresses on the landscape along with suspended sediment concentration and light attenuation characteristics were then calculated and spatially averaged to examine how actual cover and mean water depth affect the bulk sediment and light environment. The results indicate that an effective cover, which incorporates the sheltering area, has important controls on the distributions of shear stress, suspended sediment, light environment, and consequent seagrass habitat suitability. Interestingly, an optimal habitat occurs within a depth range where, if actual cover is reduced past some threshold, the bulk light environment would no longer favor seagrass growth.

  13. INTER LABORATORY COMBAT HELMET BLUNT IMPACT TEST METHOD COMPARISON

    Science.gov (United States)

    2018-03-26

    data by Instrumentation for Impact  Test , SAE standard J211‐1 [4]. Although the entire curve is collected, the interest of this  project  team  solely...HELMET BLUNT IMPACT TEST METHOD COMPARISON by Tony J. Kayhart Charles A. Hewitt and Jonathan Cyganik March 2018 Final...INTER-LABORATORY COMBAT HELMET BLUNT IMPACT TEST METHOD COMPARISON 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR

  14. Blanket comparison and selection study. Final report. Volume 1

    International Nuclear Information System (INIS)

    1984-09-01

    The study focused on: (1) Development of reference design guidelines, evaluation criteria, and a methodology for evaluating and ranking candidate blanket concepts. (2) Compilation of the required data base and development of a uniform systems analysis for comparison. (3) Development of conceptual designs for the comparative evaluation. (4) Evaluation of leading concepts for engineering feasibility, economic performance, and safety. (5) Identification and prioritization of R and D requirements for the leading blanket concepts. Sixteen concepts (nine TMR and seven tokamak) which were identified as leading candidates in the early phases of the study, were evaluated in detail. The overall evaluation concluded that the following concepts should provide the focus for the blanket R and D program: (Breeder/Coolant/Structure), Lithium/Lithium/Vanadium Alloy, Li 2 O/Helium/Ferritic Steel, LiPb Alloy/LiPb Alloy/Vanadium Alloy, and Lithium/Helium/Ferritic Steel. The primary R and D issues for the Li/Li/V concept are the development of an advanced structural alloy, resolution of MHD and corrosion problems, provision for an inert atmosphere (e.g., N 2 ) in the reactor building, and the development of non-water cooled near-plasma components, particularly for the tokamak. The main issues for the LiPb/LiPb/V concept are similar to the Li/Li/V blanket with the addition of resolving the tritium recovery issue. The R and D issues for Li 2 O/He/FS concept include resolution of the tritium recovery/containment issue, achieving adequate tritium breeding and resolving other solid breeder issues such as swelling and fabrication concerns. Major concerns for the Li/He/FS concept are related to its rather poor economic performance. Improvement of its economic performance will be somewhat concept-dependent and will be more of a systems engineering issue

  15. Blanket comparison and selection study. Final report. Volume 2

    Energy Technology Data Exchange (ETDEWEB)

    1984-09-01

    The study focused on: (1) Development of reference design guidelines, evaluation criteria, and a methodology for evaluating and ranking candidate blanket concepts. (2) Compilation of the required data base and development of a uniform systems analysis for comparison. (3) Development of conceptual designs for the comparative evaluation. (4) Evaluation of leading concepts for engineering feasibility, economic performance, and safety. (5) Identification and prioritization of R and D requirements for the leading blanket concepts. Sixteen concepts (nine TMR and seven tokamak) which were identified as leading candidates in the early phases of the study, were evaluated in detail. The overall evaluation concluded that the following concepts should provide the focus for the blanket R and D program: (Breeder/Coolant/Structure), Lithium/Lithium/Vanadium Alloy, Li/sub 2/O/Helium/Ferritic Steel, LiPb Alloy/LiPb Alloy/Vanadium Alloy, and Lithium/Helium/Ferritic Steel. The primary R and D issues for the Li/Li/V concept are the development of an advanced structural alloy, resolution of MHD and corrosion problems, provision for an inert atmosphere (e.g., N/sub 2/) in the reactor building, and the development of non-water cooled near-plasma components, particularly for the tokamak. The main issues for the LiPb/LiPb/V concepts are similar to the Li/Li/V blanket with the addition of resolving the tritium recovery issue. The R and D issues for Li/sub 2/O/He/FS concept include resolution of the tritium recovery/containment issue, achieving adequate tritium breeding and resolving other solid breeder issues such as swelling and fabrication concerns. Major concerns for the Li/He/FS concept are related to its rather poor economic performance. Improvement of its economic performance will be somewhat concept-dependent and will be more of a systems engineering issue.

  16. Blanket comparison and selection study. Final report. Volume 3

    International Nuclear Information System (INIS)

    1984-09-01

    The study focused on: (1) Development of reference design guidelines, evaluation criteria, and a methodology for evaluating and ranking candidate blanket concepts. (2) Compilation of the required data base and development of a uniform systems analysis for comparison. (3) Development of conceptual designs for the comparative evaluation. (4) Evaluation of leading concepts for engineering feasibility, economic performance, and safety. (5) Identification and prioritization of R and D requirements for the leading blanket concepts. Sixteen concepts (nine TMR and seven tokamak) which were identified as leading candidates in the early phases of the study, were evaluated in detail. The overall evaluation concluded that the following concepts should provide the focus for the blanket R and D program: (Breeder/Coolant/Structure), Lithium/Lithium/Vanadium Alloy, Li 2 O/Helium/Ferritic Steel, LiPb Alloy/LiPb Alloy/Vanadium Alloy, and Lithium/Helium/Ferritic Steel. The primary R and D issues for the Li/Li/V concept are the development of an advanced structural alloy, resolution of MHD and corrosion problems, provision for an inert atmosphere (e.g., N 2 ) in the reactor building, and the development of non-water cooled near-plasma components, particularly for the tokamak. The main issues for the LiPb/LiPb/V concept are similar to the Li/Li/V blanket with the addition of resolving the tritium recovery issue. The R and D issues for Li 2 O/He/FS concept include resolution of the tritium recovery/containment issue, achieving adequate tritium breeding and resolving other solid breeder issues such as swelling and fabrication concerns. Major concerns for the Li/He/FS concepts are related to its rather poor economic performance. Improvement of its economic performance will be somewhat concept-dependent and will be more of a systems engineering issue

  17. Blanket comparison and selection study. Final report. Volume 2

    International Nuclear Information System (INIS)

    1984-09-01

    The study focused on: (1) Development of reference design guidelines, evaluation criteria, and a methodology for evaluating and ranking candidate blanket concepts. (2) Compilation of the required data base and development of a uniform systems analysis for comparison. (3) Development of conceptual designs for the comparative evaluation. (4) Evaluation of leading concepts for engineering feasibility, economic performance, and safety. (5) Identification and prioritization of R and D requirements for the leading blanket concepts. Sixteen concepts (nine TMR and seven tokamak) which were identified as leading candidates in the early phases of the study, were evaluated in detail. The overall evaluation concluded that the following concepts should provide the focus for the blanket R and D program: (Breeder/Coolant/Structure), Lithium/Lithium/Vanadium Alloy, Li 2 O/Helium/Ferritic Steel, LiPb Alloy/LiPb Alloy/Vanadium Alloy, and Lithium/Helium/Ferritic Steel. The primary R and D issues for the Li/Li/V concept are the development of an advanced structural alloy, resolution of MHD and corrosion problems, provision for an inert atmosphere (e.g., N 2 ) in the reactor building, and the development of non-water cooled near-plasma components, particularly for the tokamak. The main issues for the LiPb/LiPb/V concepts are similar to the Li/Li/V blanket with the addition of resolving the tritium recovery issue. The R and D issues for Li 2 O/He/FS concept include resolution of the tritium recovery/containment issue, achieving adequate tritium breeding and resolving other solid breeder issues such as swelling and fabrication concerns. Major concerns for the Li/He/FS concept are related to its rather poor economic performance. Improvement of its economic performance will be somewhat concept-dependent and will be more of a systems engineering issue

  18. Supplier Evaluation Process by Pairwise Comparisons

    Directory of Open Access Journals (Sweden)

    Arkadiusz Kawa

    2015-01-01

    Full Text Available We propose to assess suppliers by using consistency-driven pairwise comparisons for tangible and intangible criteria. The tangible criteria are simpler to compare (e.g., the price of a service is lower than that of another service with identical characteristics. Intangible criteria are more difficult to assess. The proposed model combines assessments of both types of criteria. The main contribution of this paper is the presentation of an extension framework for the selection of suppliers in a procurement process. The final weights are computed from relative pairwise comparisons. For the needs of the paper, surveys were conducted among Polish managers dealing with cooperation with suppliers in their enterprises. The Polish practice and restricted bidding are discussed, too.

  19. Characterization of weakly excited final states by shakedown spectroscopy of laser-excited potassium

    International Nuclear Information System (INIS)

    Schulz, J.; Heinaesmaeki, S.; Aksela, S.; Aksela, H.; Sankari, R.; Rander, T.; Lindblad, A.; Bergersen, H.; Oehrwall, G.; Svensson, S.; Kukk, E.

    2006-01-01

    3p shakedown spectra of laser excited potassium atoms as well as direct 3p photoemission of ground state potassium have been studied. These two excitation schemes lead to the same final states and thereby provide a good basis for a detailed study of the 3p 5 (4s3d) 1 configurations of singly ionized potassium and the photoemission processes leading to these configurations. The comparison of direct photoemission from the ground state and conjugate shakedown spectra from 4p 1/2 laser excited potassium made it possible to experimentally determine the character of final states that are only weakly excited in the direct photoemission but have a much higher relative intensity in the shakedown spectrum. Based on considerations of angular momentum and parity conservation the excitation scheme of the final states can be understood

  20. Comparisons of radiation dosimetry between Louvain (Belgium) and Edinburgh (UK)

    International Nuclear Information System (INIS)

    Law, J.; Prignot, M.; Wambersie, A.

    1975-01-01

    A comparison of radiation dosimetry performed between Edinburgh and Louvain using the FeSO 4 system, was reported. The procedure adopted provided comparisons both of solution response and of spectrophotometer calibration, and also provided a comparison of ionization dosimetry and irradiation techniques at the two centres. Therefore dosimeter solutions were prepared in both centres, FeSO 4 samples were irradiated either in Edinburgh (4 MV X-rays) or in Louvain ( 60 Co), finally optical densities were measured using the spectrophotometer of either centre. For these different comparisons, the samples were transported once of twice. An agreement between the two centres better than 1% was observed, both for ionization dosimetry and irradiation techniques and for spectrophotometer calibration. The ratio of Louvain to Edinburgh solution response was found close to 1 (0.998+-0.004). However, a previous comparison showed a discrepancy of 2% which illustrates the care needed in checking the purity of the solution components and mainly of the distilled water

  1. COOMET pilot comparison 473/RU-a/09: Comparison of hydrophone calibrations in the frequency range 250 Hz to 200 kHz

    Science.gov (United States)

    Yi, Chen; Isaev, A. E.; Yuebing, Wang; Enyakov, A. M.; Teng, Fei; Matveev, A. N.

    2011-01-01

    A description is given of the COOMET project 473/RU-a/09: a pilot comparison of hydrophone calibrations at frequencies from 250 Hz to 200 kHz between Hangzhou Applied Acoustics Research Institute (HAARI, China)—pilot laboratory—and Russian National Research Institute for Physicotechnical and Radio Engineering Measurements (VNIIFTRI, Designated Institute of Russia of the CIPM MRA). Two standard hydrophones, B&K 8104 and TC 4033, were calibrated and compared to assess the current state of hydrophone calibration of HAARI (China) and Russia. Three different calibration methods were applied: a vibrating column method, a free-field reciprocity method and a comparison method. The standard facilities of each laboratory were used, and three different sound fields were applied: pressure field, free-field and reverberant field. The maximum deviation of the sensitivities of two hydrophones between the participants' results was 0.36 dB. Main text. To reach the main text of this paper, click on Final Report. The final report has been peer-reviewed and approved for publication by the CCAUV-KCWG.

  2. The pion contribution to semi-inclusive deep inelastic scattering with slow baryons in the final state

    NARCIS (Netherlands)

    Korpa, C. L.; Dieperink, A. E. L.; Scholten, O.

    1992-01-01

    We analyze the pion-exchange contribution to semi-inclusive leptoproduction on protons, with a slow nucleon or delta in the final state. We calculate the crosssection for slow protons including also the effect of the delta intermediate state, which is the dominant contribution. A comparison with

  3. Pairwise Comparison and Distance Measure of Hesitant Fuzzy Linguistic Term Sets

    Directory of Open Access Journals (Sweden)

    Han-Chen Huang

    2014-01-01

    Full Text Available A hesitant fuzzy linguistic term set (HFLTS, allowing experts using several possible linguistic terms to assess a qualitative linguistic variable, is very useful to express people’s hesitancy in practical decision-making problems. Up to now, a little research has been done on the comparison and distance measure of HFLTSs. In this paper, we present a comparison method for HFLTSs based on pairwise comparisons of each linguistic term in the two HFLTSs. Then, a distance measure method based on the pairwise comparison matrix of HFLTSs is proposed, and we prove that this distance is equal to the distance of the average values of HFLTSs, which makes the distance measure much more simple. Finally, the pairwise comparison and distance measure methods are utilized to develop two multicriteria decision-making approaches under hesitant fuzzy linguistic environments. The results analysis shows that our methods in this paper are more reasonable.

  4. 75 FR 62765 - Silicon Metal From the People's Republic of China; Extension of Time Limit for the Final Results...

    Science.gov (United States)

    2010-10-13

    .... Extension of Time Limit for Final Results Section 751(a)(3)(A) of the Tariff Act of 1930, as amended (``the... surrogate financial ratios, the valuation of silica fume and coal, and questions regarding comparisons...

  5. Task-Driven Comparison of Topic Models.

    Science.gov (United States)

    Alexander, Eric; Gleicher, Michael

    2016-01-01

    Topic modeling, a method of statistically extracting thematic content from a large collection of texts, is used for a wide variety of tasks within text analysis. Though there are a growing number of tools and techniques for exploring single models, comparisons between models are generally reduced to a small set of numerical metrics. These metrics may or may not reflect a model's performance on the analyst's intended task, and can therefore be insufficient to diagnose what causes differences between models. In this paper, we explore task-centric topic model comparison, considering how we can both provide detail for a more nuanced understanding of differences and address the wealth of tasks for which topic models are used. We derive comparison tasks from single-model uses of topic models, which predominantly fall into the categories of understanding topics, understanding similarity, and understanding change. Finally, we provide several visualization techniques that facilitate these tasks, including buddy plots, which combine color and position encodings to allow analysts to readily view changes in document similarity.

  6. Quantitative microbial risk assessment (QMRA) shows increased public health risk associated with exposure to river water under conditions of riverbed sediment resuspension.

    Science.gov (United States)

    Abia, Akebe Luther King; Ubomba-Jaswa, Eunice; Genthe, Bettina; Momba, Maggy Ndombo Benteke

    2016-10-01

    Although higher microbial concentrations have been reported in sediments than in the overlying water column, most quantitative microbial risk assessment (QMRA) studies have not clearly indicated the contribution of sediment-borne pathogens to estimated risks. Thus, the present study aimed at determining the public health risk associated with exposure to pathogenic bacteria in polluted river water under undisturbed conditions and conditions of sediment resuspension in the Apies River, Gauteng, South Africa. Microbial pathogens were isolated and identified using culture and molecular methods. The beta-Poisson dose-response model was used to estimate the probability of infection (Pi) with the various pathogens, following accidental/intentional ingestion of 1mL or 100mL (or 50mL) of untreated river water. Mean wet season Escherichia coli counts ranged between 5.8E+01 and 8.8E+04MPN/100mL (water column) and between 2.40E+03 and 1.28E+05MPN/100mL (sediments). Mean dry season E. coli counts ranged between 5.11E+00 and 3.40E+03MPN/100mL (water column) and between 5.09E+00 and 6.30E+03MPN/100mL (sediments). Overall (water and sediments) Vibrio cholerae was the most detected pathogen (58.8%) followed by Salmonella spp. (23.9%) and Shigella (10.1%). Ingestion of 1mL of river water could lead to 0%-4% and 1%-74% Pi with E. coli during the dry and wet season, respectively. During the dry season, the Pi with V. cholerae, Salmonella spp. and Shigella spp. were 0%-1.39%, 0%-4.11% and 0%-0.16% respectively, depending on volume of water ingested. The risks of infections with all microorganisms increased during the wet season. A 2-log increase in water E. coli count following sediments disturbance led to approximately 10 times higher Pi with E. coli than when sediments were undisturbed. Therefore, the use of the untreated water from the Apies River for drinking, household purposes or recreational activities poses a potential health risk to the users of the river. Copyright © 2016

  7. Comparison of different target material options for the European Spallation Source based on certain aspects related to the final disposal

    Science.gov (United States)

    Kókai, Zsófia; Török, Szabina; Zagyvai, Péter; Kiselev, Daniela; Moormann, Rainer; Börcsök, Endre; Zanini, Luca; Takibayev, Alan; Muhrer, Günter; Bevilacqua, Riccardo; Janik, József

    2018-02-01

    Different target options have been examined for the European Spallation Source, which is under construction in Lund, Sweden. During the design update phase, parameters and characteristics for the target design have been optimized not only for neutronics but also with respect to the waste characteristics related to the final disposal of the target. A rotating, solid tungsten target was eventually selected as baseline concept; the other options considered included mercury and lead-bismuth (LBE) targets suitable for a pulsed source. Since the licensee is obliged to present a decommissioning plan even before the construction phase starts, the radioactive waste category of the target after full operation time is of crucial importance. The results obtained from a small survey among project partners of 7th Framework Program granted by EU 202247 contract have been used. Waste characteristics of different potential spallation target materials were compared. Based on waste index, the tungsten target is the best alternative and the second one is the mercury target. However, all alternatives have HLW category after a 10 year cooling. Based on heat generation alone all of the options would be below the HLW limit after this cooling period. The LBE is the least advantageous alternative based on waste index and heat generation comparison. These results can be useful in compiling the licensing documents of the ESS facility as the target alternatives can be compared from various aspects related to their disposal.

  8. Comparison of measurement standards of the acoustic pressure in air in the low frequency range: COOMET.AUV.A-K2

    Science.gov (United States)

    Chalyy, V.

    2011-01-01

    A bilateral regional comparison of national microphone standards from 2 Hz to 250 Hz was carried out between the DP NDI 'Systema' (Ukraine) and the VNIIFTRI (Russia) from July to September 2009. The comparison, COOMET.AUV.A-K2, was based on the pressure calibration of laboratory standard microphones type LSIP. The comparison results have been linked to the established key comparison reference value (KCRV) of CCAUV.A-K2. The degrees of equivalence, expressed as the deviation from the established KCRV and its expanded uncertainty (k = 2), have been determined, and the comparison result is in agreement with the KCRV within the estimated uncertainties at all employed frequencies. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCAUV, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

  9. KEY COMPARISON: CCT-K2.1: NRC/VNIIFTRI bilateral comparison of capsule-type standard platinum resistance thermometers from 13.8 K to 273.16 K

    Science.gov (United States)

    Hill, K. D.; Steele, A. G.; Dedikov, Y. A.; Shkraba, V. T.

    2005-01-01

    The Consultative Committee for Thermometry Key Comparison 2 (CCT-K2) results were published two years ago (2002 Metrologia 39 551-71). NRC served as the pilot laboratory for CCT-K2 and remains able to provide a scale and measurement system suitable for performing bilateral comparisons linked to the original key comparison results. In March 2003, measurements of two VNIIFTRI 100 Ω capsule-style platinum resistance thermometers (CSPRTs), S/N 356 and 476, were undertaken to relate their local calibration to the results from the CCT-K2 exercise. The NRC Leeds and Northrup (L&N) CSPRT S/N 1872174 provides the link to the CCT-K2 results. The three CSPRTs were compared at the eight defining cryogenic temperatures of the International Temperature Scale of 1990 (ITS-90) in the range from 13.8033 K to 273.16 K. The reader is referred to the full text of the CCT-K2 report for a detailed explanation of the methodology employed for the comparison. Only the details unique to the measurements reported here will be addressed in this article. The NRC/VNIIFTRI bilateral comparison of capsule-style platinum resistance thermometers over the range 13.8 K to 273.16 K has revealed calibrations at VNIIFTRI to be in agreement with the KCRV of CCT-K2 within the expanded uncertainty for all temperatures of the comparison with the exception of the triple point of hydrogen at 13.8033 K. One of the two CSPRTs supplied by VNIIFTRI was found to be discrepant as revealed by differences at the triple point of water and at the lowest temperatures of the comparison, and was therefore excluded from further analysis. The linkage to the CCT-K2 data supports the evaluation of the VNIIFTRI CMCs in Appendix C of the KCDB. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCT, according to the provisions

  10. Data base of climatic change simulations for the impact studies. Final report; Base de donnees des simulations de changement climatique a l'usage des etudes d'impact. Rapport final

    Energy Technology Data Exchange (ETDEWEB)

    Polcher, J.; Leboucher, V.; Planton, S.; Valcke, S

    2003-12-15

    Data used for the study of the climatic change impact on the environment and the society come from climate models and are affected by uncertainties. It is necessary to quantify the resulting errors in the models. The data base provides a comparison of simulations of climatic change in France. The final report presents the project methodology. Three projects using the distributed simulations are also presented. (A.L.B.)

  11. Final results for the excitation function and angular distributions of the 3H(d,n)4He reaction

    International Nuclear Information System (INIS)

    Tang Hongqing; Zhou Zuying; Qi Bujia; Zhou Chenwei; Du Yanfeng; Xia Haihong; Chen Zemin; Chen Zhenpeng; Chen Yingtang

    1998-01-01

    The final relative excitation function of the 3 H(d,n) 4 He rection at 0 degree is shown out. For comparison, a curve calculated from Drosg's HI-13 tandem is in progressplotted. The angular distributions of the 3 H(d,n) 4 He reaction at E d =13.36, 16.50 and 19.50 Mev in the center-of-mass system are shown out. A comparison of the legendre polynomial coefficients obtained from the present angular distribution data with Drosg's evaluation are reported

  12. Final report on CCQM-K9.2 : subsequent key comparison on pH determination of phosphate buffer by Harned cell measurements

    OpenAIRE

    Spitzer, Petra; Giera, Janine; Fraga, Isabel Cristina Serta; Jakobsen, Pia Tonnes; Jensen, Hans D.; Hyllested, Peter; Karpov, Oleg; Kutovoy, Viatcheslav; Nakamura, Susumu; Vospelova, Alena; Zvezdina, Valentina

    2008-01-01

    CCQM-K9.2 was performed supplementary to the key comparison CCQM-K9 [1] on the pH determination of a phosphate buffer with nominal pH ~ 6.9 (at 25 °C). The sample composition was very similar in both comparisons. Only the source of the starting material used for sample preparation was different. The comparison was restricted to the use of the primary method for pH (Harned cell measurement) as defined in the IUPAC Recommendations [2]. The measurement temperatures were15 °C, 25 °C , 37...

  13. Comparison of a Wooden House and a Porous Concrete Masonry House

    Directory of Open Access Journals (Sweden)

    Ďurica Pavol

    2014-07-01

    Full Text Available This paper deals with an evaluation of an existing wooden panel house and its comparison with alternative material composition (porous concrete masonry house. The criteria for evaluation are the energy performance, size of the usable area, environmental impact and final costs.

  14. A general comparison between tokamak and stellarator plasmas

    Directory of Open Access Journals (Sweden)

    Yuhong Xu

    2016-07-01

    Full Text Available This paper generally compares the essential features between tokamaks and stellarators, based on previous review work individually made by authors on several specific topics, such as theories, bulk plasma transport and edge divertor physics, along with some recent results. It aims at summarizing the main results and conclusions with regard to the advantages and disadvantages in these two types of magnetic fusion devices. The comparison includes basic magnetic configurations, magnetohydrodynamic (MHD instabilities, operational limits and disruptions, neoclassical and turbulent transport, confinement scaling and isotopic effects, plasma rotation, and edge and divertor physics. Finally, a concept of quasi-symmetric stellarators is briefly referred along with a comparison of future application for fusion reactors.

  15. Ethical aspects of final disposal. Final report

    International Nuclear Information System (INIS)

    Baltes, B.; Leder, W.; Achenbach, G.B.; Spaemann, R.; Gerhardt, V.

    2003-01-01

    In fulfilment of this task the Federal Environmental Ministry has commissioned GRS to summarise the current national and international status of ethical aspects of the final disposal of radioactive wastes as part of the project titled ''Final disposal of radioactive wastes as seen from the viewpoint of ethical objectives''. The questions arising from the opinions, positions and publications presented in the report by GRS were to serve as a basis for an expert discussion or an interdisciplinary discussion forum for all concerned with the ethical aspects of an answerable approach to the final disposal of radioactive wastes. In April 2001 GRS held a one-day seminar at which leading ethicists and philosophers offered statements on the questions referred to above and joined in a discussion with experts on issues of final disposal. This report documents the questions that arose ahead of the workshop, the specialist lectures held there and a summary of the discussion results [de

  16. Search for SUSY in final states with photons at CMS

    Directory of Open Access Journals (Sweden)

    Ntomari Eleni

    2013-05-01

    Full Text Available Résumé The Compact Muon Solenoid (CMS collaboration has developed a complete program of searches beyond the Standard Model (SM covering a wide range of final states. This document focuses on searches in final states with photons and missing transverse energy ETmiss organised in three analyses. The first two include comparison of the ETmiss distribution (isolation sideband method in events with either at least two photons plus at least one hadronic jet, or at least one photon plus at least two hadronic jets. The third analysis corresponds to a new approach, the Jet-Gamma Balance (JGB method, for events with at least one photon plus at least three hadronic jets.We observe no significant deviations from the SM expectation and thus derive upper limits on the signal cross section at the 95% confidence level (CL for a range of squark, gluino and neutralino mass points in the Gauge Mediated Supersymmetry Breaking scenario.

  17. Brain mechanisms of social comparison and their influence on the reward system.

    Science.gov (United States)

    Kedia, Gayannée; Mussweiler, Thomas; Linden, David E J

    2014-11-12

    Whenever we interact with others, we judge them and whenever we make such judgments, we compare them with ourselves, other people, or internalized standards. Countless social psychological experiments have shown that comparative thinking plays a ubiquitous role in person perception and social cognition as a whole. The topic of social comparison has recently aroused the interest of social neuroscientists, who have begun to investigate its neural underpinnings. The present article provides an overview of these neuroimaging and electrophysiological studies. We discuss recent findings on the consequences of social comparison on the brain processing of outcomes and highlight the role of the brain's reward system. Moreover, we analyze the relationship between the brain networks involved in social comparisons and those active during other forms of cognitive and perceptual comparison. Finally, we discuss potential future questions that research on the neural correlates of social comparison could address.

  18. Bilateral key comparison SIM.T-K6.1 on humidity standards in the dew/frost-point temperature range from -25 °C to +20 °C

    Science.gov (United States)

    Meyer, C. W.; Hill, K. D.

    2015-01-01

    A Regional Metrology Organization (RMO) Key Comparison of dew/frost point temperatures was carried out by the National Institute of Standards and Technology (NIST, USA) and the National Research Council (NRC, Canada) between December 2014 and April 2015. The results of this comparison are reported here, along with descriptions of the humidity laboratory standards for NIST and NRC and the uncertainty budget for these standards. This report also describes the protocol for the comparison and presents the data acquired. The results are analyzed, determining degree of equivalence between the dew/frost-point standards of NIST and NRC. This paper is the final report of the comparison including analysis of the uncertainty of measurement results. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCT WG-KC, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

  19. 2287-IJBCS-Article-Seyni Sané

    African Journals Online (AJOL)

    hp

    interaction entre la resuspension et la sédimentation. Cette étude est consacrée à la détermination des processus responsables de la resuspension des particules dans le lac de Guiers situé au nord du Sénégal. Des échantillons ont été collectés au.

  20. Statistical aspects of the 1980 solar flares. Part 3: Parametric comparison and final comments

    International Nuclear Information System (INIS)

    Wilson, R.M.

    1983-04-01

    The 1349 study flares are considered addressing relationships between pairs of specific study paremeters namely, H alpha rise time versus H alpha importance, X-ray class and H alpha decay time, H alpha decay time versus H alpha importance, and X-ray class, and H alpha importance versus X-ray class. Mean H alpha rise time and decay time versus X-ray class and H alpha importance will also be discussed, and some final comments regarding the study flares are given

  1. Supplement to CCM.D-K4 'Hydrometer' report: linkage of EURAMET.M.D-K4 comparison, SIM.M.D-K4 comparison and the supplementary SIM.M.D-S2 to CCM.D-K4 'Hydrometer'

    Science.gov (United States)

    Lorefice, S.; Becerra, L. O.

    2017-01-01

    Evaluation of different types of comparisons to a common set of reference values of a CIPM key comparison is essential to satisfy the concept of the CIPM Mutual Recognition Arrangement (CIPM MRA), where the DoEs of any participant who took part in comparisons should be within the Calibration and Measurement Capability (CMC) section of the CIPM MRA Key Comparison Data Base. The subject of this supplementary report is therefore to present the equivalence of each National Metrological Institute (NMI) participant in the CCM.D-K4 'Hydrometer' key comparison, which was performed in the density range 600 kg/m3 to 2000 kg/m3 at the temperature of 20 °C, and the linkage of the European and Inter-American NMI results performed in the RMO.M.D-K4 comparisons as well as those of the supplementary SIM.M.D-S2 to the common set of KCRVs of the CCM.D-K4 'Hydrometer'. The linking procedure has been obtained by numerical simulation, based on the Monte Carlo method, in which the differences in the results of the different comparison between the intended laboratory and one or more linking laboratory/ies, which took part in both comparisons, are correlated with a continuous function describing the DoEs of the linking laboratory/ies with respect to the common set of KCRVs of the CCM.D-K4. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

  2. 7X performance results - final report : ASCI Red vs Red Storm.

    Energy Technology Data Exchange (ETDEWEB)

    Dinge, Dennis C. (Cray Inc., Albuquerque, NM); Davis, Michael E. (Cray Inc., Albuquerque, NM); Haskell, Karen H.; Ballance, Robert A.; Gardiner, Thomas Anthony; Stevenson, Joel O.; Noe, John P.

    2011-04-01

    The goal of the 7X performance testing was to assure Sandia National Laboratories, Cray Inc., and the Department of Energy that Red Storm would achieve its performance requirements which were defined as a comparison between ASCI Red and Red Storm. Our approach was to identify one or more problems for each application in the 7X suite, run those problems at multiple processor sizes in the capability computing range, and compare the results between ASCI Red and Red Storm. The first part of this report describes the two computer systems, the applications in the 7X suite, the test problems, and the results of the performance tests on ASCI Red and Red Storm. During the course of the testing on Red Storm, we had the opportunity to run the test problems in both single-core mode and dual-core mode and the second part of this report describes those results. Finally, we reflect on lessons learned in undertaking a major head-to-head benchmark comparison.

  3. KEY COMPARISON: Key comparison CCQM-K60: Total selenium and selenomethionine in selenised wheat flour

    Science.gov (United States)

    Goenaga Infante, Heidi; Sargent, Mike

    2010-01-01

    , illustrating their ability to obtain accurate results for such analytes in a complex food matrix containing approximately 17 mg kg-1 Se. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

  4. Quantification of the detriment and comparison of health risks. Methodological problems

    International Nuclear Information System (INIS)

    Jammet, H.

    1982-01-01

    Some of the methodological problems involved in the quantitative estimate of the health detriment of different energy sources and in risk comparison are described. First, the question of determining the detriment is discussed from the point of view of the distortions introduced in the quantification when dealing with risks for which the amount of information available varies widely. The main criteria applied to classifying types of detriment are then recalled. Finally, the problems involved in comparisons are outlined: spatial and temporal variations in the types of detriment, operation under normal and accident conditions, and the risks to the public and workers. (author)

  5. USING CLAY TO CONTROL RED TIDES: I. FLOCCULATION, SEDIMENTATION, AND RESUSPENSION OF CLAY/ALGAL FLOCS. (R827090)

    Science.gov (United States)

    The perspectives, information and conclusions conveyed in research project abstracts, progress reports, final reports, journal abstracts and journal publications convey the viewpoints of the principal investigator and may not represent the views and policies of ORD and EPA. Concl...

  6. Experimental determination of the kinetic conversion rate of gaseous tritium into HTO

    International Nuclear Information System (INIS)

    Gulden, W.; Guenot, J.; Djerassi, H.; Clerc, H.

    1986-09-01

    To assess the impact of atmospheric tritium releases from a fusion plant to the environment, the dose to man usually is determined under the conservative assumption that all tritium is released in the more dangerous oxide form. To quantify this overprediction, experiments are presently being performed by CEA. Oxidation of tritium gas by soil and subsequent resuspension of HTO from soil to atmosphere is one of them. First results have been obtained by CEA on the kinetics of HTO resuspension from contaminated soils. Immediately after contamination, the fraction of the deposited activity which is resuspended to atmosphere is in the range of 1% to 5% per hour. This resuspension rate then decreases more or less slowly with time, depending on specific conditions

  7. Dynamic and resuspension by waves and sedimentation pattern definition in low energy environments: guaíba lake (Brazil

    Directory of Open Access Journals (Sweden)

    João Luiz Nicolodi

    2013-03-01

    Full Text Available Little research has been undertaken into sediment dynamics in lakes, and most of it only analyses particular aspects such as the texture of the sediments. In this study, the characteristics of the wave field in Guaíba Lake are investigated. The parameters significant wave height (Hs, period (T and direction of wave propagation are examined together with their relation to the resuspension of sediments at the bottom. For this purpose, the mathematical model SWAN (Simulating Waves Nearshore has been validated and employed. The results pointed out that the highest waves modeled reached 0.55 m at a few points in the lake, particularly when winds were blowing from the S and SE quadrants with an intensity over 7 m.s-1. Generally speaking, waves follow wind intensity and direction patterns, and reach maximum height in about 1 to 2 hours after wind speed peaks. Whenever winds were stronger, waves took some 2 hours to reach 0.10 m. However, with weak to moderate winds, the waves took around 3 hours to achieve this value in significant wave height. In addition to speed and direction, wind regularity proved relevant in generating and propagating waves on Lake Guaíba. In conclusion the lake's sediment environments were mapped and classified as follows: 1 Depositional Environments (51% of the lake; 2 Transitional Environments (41%; and 3 Erosional or Non-Depositional Environments (8%. As a contribution to the region's environmental management, elements have been created relating to the concentration of suspended particulate matter.Pesquisas referentes à dinâmica sedimentar em lagos são escassas e a maioria trata da distribuição e textura dos sedimentos, sendo raras aquelas que fazem menção ao padrão de ondas e suas relações com a ressuspensão destes sedimentos e suas consequências. Este trabalho analisa as características das ondas incidentes no Lago Guaíba (Brasil por meio da utilização do SWAN (Simulating Waves Nearshore e suas rela

  8. Narrative Finality

    Directory of Open Access Journals (Sweden)

    Armine Kotin Mortimer

    1981-01-01

    Full Text Available The cloturai device of narration as salvation represents the lack of finality in three novels. In De Beauvoir's Tous les hommes sont mortels an immortal character turns his story to account, but the novel makes a mockery of the historical sense by which men define themselves. In the closing pages of Butor's La Modification , the hero plans to write a book to save himself. Through the thrice-considered portrayal of the Paris-Rome relationship, the ending shows the reader how to bring about closure, but this collective critique written by readers will always be a future book. Simon's La Bataille de Pharsale , the most radical attempt to destroy finality, is an infinite text. No new text can be written. This extreme of perversion guarantees bliss (jouissance . If the ending of De Beauvoir's novel transfers the burden of non-final world onto a new victim, Butor's non-finality lies in the deferral to a future writing, while Simon's writer is stuck in a writing loop, in which writing has become its own end and hence can have no end. The deconstructive and tragic form of contemporary novels proclaims the loss of belief in a finality inherent in the written text, to the profit of writing itself.

  9. BLEVE overpressure: multi-scale comparison of blast wave modeling

    International Nuclear Information System (INIS)

    Laboureur, D.; Buchlin, J.M.; Rambaud, P.; Heymes, F.; Lapebie, E.

    2014-01-01

    BLEVE overpressure modeling has been already widely studied but only few validations including the scale effect have been made. After a short overview of the main models available in literature, a comparison is done with different scales of measurements, taken from previous studies or coming from experiments performed in the frame of this research project. A discussion on the best model to use in different cases is finally proposed. (authors)

  10. Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Gurney, Kevin R. [Arizona Univ., Mesa, AZ (United States)

    2015-01-12

    This document constitutes the final report under DOE grant DE-FG-08ER64649. The organization of this document is as follows: first, I will review the original scope of the proposed research. Second, I will present the current draft of a paper nearing submission to Nature Climate Change on the initial results of this funded effort. Finally, I will present the last phase of the research under this grant which has supported a Ph.D. student. To that end, I will present the graduate student’s proposed research, a portion of which is completed and reflected in the paper nearing submission. This final work phase will be completed in the next 12 months. This final workphase will likely result in 1-2 additional publications and we consider the results (as exemplified by the current paper) high quality. The continuing results will acknowledge the funding provided by DOE grant DE-FG-08ER64649.

  11. CCQM-K90, formaldehyde in nitrogen, 2 μmol mol-1 Final report

    Science.gov (United States)

    Viallon, Joële; Flores, Edgar; Idrees, Faraz; Moussay, Philippe; Wielgosz, Robert Ian; Kim, D.; Kim, Y. D.; Lee, S.; Persijn, S.; Konopelko, L. A.; Kustikov, Y. A.; Malginov, A. V.; Chubchenko, I. K.; Klimov, A. Y.; Efremova, O. V.; Zhou, Z.; Possolo, A.; Shimosaka, T.; Brewer, P.; Macé, T.; Ferracci, Valerio; Brown, Richard J. C.; Aoki, Nobuyuki

    2017-01-01

    uncertainty of the trend parameters, as well as how the dispersion of the dates when measurements were made by the participants was taken into account. Upon decision of the participants, the Key Comparison Reference Values were assigned by the BIPM using the largest uncertainty for measurements performed at the BIPM, linear regression without weight to calculate the trend parameters, and not taking into account the dispersion of dates for measurements made by the participant. Each transfer standard was assigned its own reference value and associated expanded uncertainty. An expression for the degree of equivalence between each participating institute and the KCRV was calculated from the comparison results and measurement uncertainties submitted by participating laboratories. Results of the alternative mathematical treatment are presented in annex of this report. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

  12. Final Report: Summary of Findings and Recommendations for Suction Devices for Management of Prehospital Combat Casualty Care Injuries

    Science.gov (United States)

    2017-11-13

    Airway Final Report: Summary of Findings and Recommendations for Suction Devices for Management of Prehospital Combat Casualty Care Injuries...Consumer Style Comparison Table of Suction Pump Devices ............................. 103 Appendix H – Web Links for Images for Consumer- Style ...0022 pg. 6 Executive Summary Suction is a critical component of airway management , which is the second leading cause of preventable

  13. Final Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    Schuur, Edward [Northern Arizona Univ., Flagstaff, AZ (United States); Luo, Yiqi [Univ. of Oklahoma, Norman, OK (United States)

    2016-12-01

    This final grant report is a continuation of the final grant report submitted for DE-SC0006982 as the Principle Investigator (Schuur) relocated from the University of Florida to Northern Arizona University. This report summarizes the original project goals, as well as includes new project activities that were completed in the final period of the project.

  14. Preliminary case studies of economy and energy profiles for Ireland during 1979-1990. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Henry, E W

    1981-01-01

    How Irish 1985 Energy Demand Model (EDM) case study results have been optimized on the supply side, by means of the EFOM model and software, are described. The 1985 case study results are for low, likely, and high cases. The Low case represents a 1985 Irish economic profile for real GNP being 54% greater thand the GNP of 1974. The Likely case relates to 1985 real GNP being 70% greater than that of 1974, and the High to real GNP being 92% greater. The 1985 final energy results emerging from the case studies are tabulated, showing quantities of final energy required by each of the 13 sectors of the Irish EDM. In all three case studies, 5 of the 13 demand sectors take in aggregate more than 76% of the total energy; these five sectors, in decreasing size of demand, are: other household uses; other industries; private transport; cement; other services. The preparation for EFOM is described. The optimal final energy flows, with some comparisons with the non-optimal inital flows, are considered. The gross primary energy quantity and cost underlying the optimal final energy flows are examined in detail.

  15. Final-state effects on superfluid 4He in the deep inelastic regime

    International Nuclear Information System (INIS)

    Mazzanti, F.; Boronat, J.; Polls, A.

    1996-01-01

    A study of final-state effects (FSE) on the dynamic structure function of superfluid 4 He in the Gersch-Rodriguez formalism is presented. The main ingredients needed in the calculation are the momentum distribution and the semidiagonal two-body density matrix. The influence of these ground-state quantities on the FSE is analyzed. A variational form of ρ 2 is used, even though simpler forms turn out to give accurate results if properly chosen. Comparison to the experimental response at high momentum transfer is performed. The predicted response is quite sensitive to slight variations on the value of the condensate fraction, the best agreement with experiment being obtained with n 0 =0.082. Sum rules of the FSE broadening function are also derived and commented. Finally, it is shown that Gersch-Rodriguez theory produces results as accurate as those coming from other more recent FSE theories. copyright 1996 The American Physical Society

  16. Developing maintainability for fusion power systems. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Zahn, H.S.; Mantz, H.C.; Curtis, C.T.; Buchheit, R.J.; Green, W.M.; Zuckerman, D.S.

    1979-11-01

    The overall purpose of the study is to identify design features of fusion power reactors which contribute to the achievement of high levels of maintainability. Previous phases evaluated several commercial tokamak reactor design concepts. This final phase compares the maintainability of a tandem mirror reactor (TMR) commercial conceptual design with the most maintainable tokamak concept selected from earlier work. A series of maintainability design guidelines and desirable TMR design features are defined. The effects of scheduled and unscheduled maintenance for most of the reactor subsystems are defined. The comparison of the TMR and tokamak reactor maintenance costs and availabilities show that both reactors have similar costs for scheduled maintenance at 19.4 and 20.8 million dollars annually and similar scheduled downtime availability impacts, achieving approximate availabilities of 79% at optimized maintenance intervals and cost of electricity.

  17. Developing maintainability for fusion power systems. Final report

    International Nuclear Information System (INIS)

    Zahn, H.S.; Mantz, H.C.; Curtis, C.T.; Buchheit, R.J.; Green, W.M.; Zuckerman, D.S.

    1979-11-01

    The overall purpose of the study is to identify design features of fusion power reactors which contribute to the achievement of high levels of maintainability. Previous phases evaluated several commercial tokamak reactor design concepts. This final phase compares the maintainability of a tandem mirror reactor (TMR) commercial conceptual design with the most maintainable tokamak concept selected from earlier work. A series of maintainability design guidelines and desirable TMR design features are defined. The effects of scheduled and unscheduled maintenance for most of the reactor subsystems are defined. The comparison of the TMR and tokamak reactor maintenance costs and availabilities show that both reactors have similar costs for scheduled maintenance at 19.4 and 20.8 million dollars annually and similar scheduled downtime availability impacts, achieving approximate availabilities of 79% at optimized maintenance intervals and cost of electricity

  18. COOMET.RI(II)-S1.Rn-222 (169/UA/98): Rn-222 volume activity comparison

    International Nuclear Information System (INIS)

    Skliarov, V.; Rottger, A.; Honig, A.; Korostin, S.; Kuznetsov, S.; Lapenas, A.; Milevsky, V.; Ivaniukovich, A.; Kharitonov, I.; Sepman, S.

    2009-01-01

    According to a first program, a supplementary comparison of Rn-222 volume activity was drawn up as a bilateral supplementary comparison between NSC 'Institute of Metrology', Ukraine, and VNIIFTRI, Russia. It took place in March 2005. In April 2005, at the 5. meeting of COOMET held in Braunschweig (Germany), representatives of these institutes exchanged data which showed the comparability of the national standards of Ukraine and Russia for the check points. During the discussion of the procedure some other institutes decided to join the comparison program, which was extended to BelGIM (Belarus), PTB (Germany), VNIIM (Russia) and RMTC (Latvia). The national standards of volume activity of radon-222 were thus calibrated using one standard radon radiometer as the transfer standard. Results are shown in the Final Report of the comparison. (authors)

  19. COOMET.RI(II)-S1.Rn-222 (169/UA/98): Rn-222 volume activity comparison

    Energy Technology Data Exchange (ETDEWEB)

    Skliarov, V. [National Scientific Centre, Institute of Metrology (NSC IM), Kharkiv (Ukraine); Rottger, A.; Honig, A. [Physikalisch-Technische Bundesanstalt (PTB), Braunschweig (Germany); Korostin, S.; Kuznetsov, S. [All-Russian Scientific Research Institute of Physical, Technical and Radio Measurements (VNIIFTRI), Moscow Region, Mendeleyevo (Russian Federation); Lapenas, A. [Latvian National Metrology Centre Ltd, Radiation Metrology and Testing Centre (RMTC), Salaspils (Latvia); Milevsky, V.; Ivaniukovich, A. [Belarussian State Institute of Metrology (BelGIM), Minsk (Belarus); Kharitonov, I.; Sepman, S. [D I Mendeleyev Institute of metrology (VNIIM), Saint Petersburg (Russian Federation)

    2009-06-15

    According to a first program, a supplementary comparison of Rn-222 volume activity was drawn up as a bilateral supplementary comparison between NSC 'Institute of Metrology', Ukraine, and VNIIFTRI, Russia. It took place in March 2005. In April 2005, at the 5. meeting of COOMET held in Braunschweig (Germany), representatives of these institutes exchanged data which showed the comparability of the national standards of Ukraine and Russia for the check points. During the discussion of the procedure some other institutes decided to join the comparison program, which was extended to BelGIM (Belarus), PTB (Germany), VNIIM (Russia) and RMTC (Latvia). The national standards of volume activity of radon-222 were thus calibrated using one standard radon radiometer as the transfer standard. Results are shown in the Final Report of the comparison. (authors)

  20. 40 CFR 61.134 - Standard: Naphthalene processing, final coolers, and final-cooler cooling towers.

    Science.gov (United States)

    2010-07-01

    ... coolers, and final-cooler cooling towers. 61.134 Section 61.134 Protection of Environment ENVIRONMENTAL... Standard: Naphthalene processing, final coolers, and final-cooler cooling towers. (a) No (“zero”) emissions are allowed from naphthalene processing, final coolers and final-cooler cooling towers at coke by...

  1. Wind effected redistribution of surface contamination. Progress report, September 1974--August 1975

    International Nuclear Information System (INIS)

    Amato, A.J.

    1975-01-01

    Theoretical resuspension ratios were computed through the extension of a one-dimensional model used to simulate the wind effected movement of surface contaminants. The surface movement of contamination associated with inhalable size particles was considered in relation to time, space, wind velocity, distance from the source, soil resuspension ratios, and other variables. A computer program was developed to calculate the wind effected distribution of surface contaminants. (U.S.)

  2. Re-analysis as a Comparison of Constructions

    Directory of Open Access Journals (Sweden)

    Jochen Gläser

    2000-12-01

    Full Text Available An interesting methodological aspect of secondary analysis is that it enables comparisons between constructions that constitute qualitative data analysis. This comparison is even more focused if a reanalysis is conducted, that means an analysis that reexamines both the primary study's data and the primary study's research question. In this article, a reanalysis is described that used interviews from the archive at the Special Collaborative Centre 186 (Sfb 186. One of the primary study's results was formulated as a hypothesis and subsequently "tested" by conducting a qualitative content analysis of the interviews. A comparison of primary study and reanalysis reveals critical decisions which may lead the data analyses to different results. These decisions are usually made implicitly and will show up only if contradictions between results are explained. As a second result of the comparison, typical threats to primary and secondary analyses are discussed. Primary studies seem to suffer from a "closure pressure", that it is a necessity to make sense of the data at all costs. This may stimulate researchers to close gaps in their data by speculation and to neglect contradicting evidence. Secondary analyses are thematically and methodically restricted by the primary study's data collection. Finally, the reanalysis confirmed that it is possible to use interviews from archives: The losses of information due to archiving and anonymisation seemed to have no significant influence on the reanalysis. URN: urn:nbn:de:0114-fqs0003257

  3. The AGP-Project conceptual design for a Spanish HLW final disposal facility

    International Nuclear Information System (INIS)

    Biurrun, E.; Engelmann, H.-J.; Huertas, F.; Ulibarri, A.

    1992-01-01

    Within the framework of the AGP Project a Conceptual Design for a HLW Final Disposal Facility to be eventually built in an underground salt formation in Spain has been developed. The AGP Project has the character of a system analysis. In the current project phase I several alternatives has been considered for different subsystems and/or components of the repository. The system variants, developed to such extent as to allow a comparison of their advantages and disadvantages, will allow the selection of a reference concept, which will be further developed to technical maturity in subsequent project phases. (author)

  4. Traceable size determination of nanoparticles, a comparison among European metrology institutes

    International Nuclear Information System (INIS)

    Meli, Felix; Klein, Tobias; Buhr, Egbert; Frase, Carl Georg; Gleber, Gudrun; Krumrey, Michael; Duta, Alexandru; Duta, Steluta; Korpelainen, Virpi; Bellotti, Roberto; Picotto, Gian Bartolo; Boyd, Robert D; Cuenat, Alexandre

    2012-01-01

    Within the European iMERA-Plus project ‘Traceable Characterisation of Nanoparticles’ various particle measurement procedures were developed and finally a measurement comparison for particle size was carried out among seven laboratories across six national metrology institutes. Seven high quality particle samples made from three different materials and having nominal sizes in the range from 10 to 200 nm were used. The participants applied five fundamentally different measurement methods, atomic force microscopy, dynamic light scattering (DLS), small-angle x-ray scattering, scanning electron microscopy and scanning electron microscopy in transmission mode, and provided a total of 48 independent, traceable results. The comparison reference values were determined as weighted means based on the estimated measurement uncertainties of the participants. The comparison reference values have combined standard uncertainties smaller than 1.4 nm for particles with sizes up to 100 nm. All methods, except DLS, provided consistent results. (paper)

  5. Key comparison BIPM.RI(I)-K1 of the air-kerma standards of the MKEH, Hungary and the BIPM in 60Co gamma radiation

    Science.gov (United States)

    Kessler, C.; Burns, D.; Machula, G.

    2018-01-01

    A comparison of the standards for air kerma of the Hungarian Trade Licensing Office (MKEH), Hungary and of the Bureau International des Poids et Mesures (BIPM) was carried out in the 60Co radiation beam of the BIPM in March 2016. The comparison result, evaluated as a ratio of the MKEH and the BIPM standards for air kerma, is 1.0047 with a combined standard uncertainty of 1.9 × 10-3. The results for an indirect comparison made at the same time are consistent with the direct results at the level of 2.6 parts in 103. The results are analysed and presented in terms of degrees of equivalence, suitable for entry in the BIPM key comparison database. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCRI, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

  6. A model independent search for new physics in final states containing leptons at the D0 experiment

    International Nuclear Information System (INIS)

    Piper, Joel Michael

    2009-01-01

    The standard model is known to be the low energy limit of a more general theory. Several consequences of the standard model point to a strong probability of new physics becoming experimentally visible in high energy collisions of a few TeV, resulting in high momentum objects. The specific signatures of these collisions are topics of much debate. Rather than choosing a specific signature, this analysis broadly searches the data, preferring breadth over sensitivity. In searching for new physics, several different approaches are used. These include the comparison of data with standard model background expectation in overall number of events, comparisons of distributions of many kinematic variables, and finally comparisons on the tails of distributions that sum the momenta of the objects in an event. With 1.07 fb -1 at the D0 experiment, we find no evidence of physics beyond the standard model. Several discrepancies from the standard model were found, but none of these provide a compelling case for new physics.

  7. A model independent search for new physics in final states containing leptons at the D0 experiment

    Energy Technology Data Exchange (ETDEWEB)

    Piper, Joel Michael [Michigan State Univ., East Lansing, MI (United States)

    2009-01-01

    The standard model is known to be the low energy limit of a more general theory. Several consequences of the standard model point to a strong probability of new physics becoming experimentally visible in high energy collisions of a few TeV, resulting in high momentum objects. The specific signatures of these collisions are topics of much debate. Rather than choosing a specific signature, this analysis broadly searches the data, preferring breadth over sensitivity. In searching for new physics, several different approaches are used. These include the comparison of data with standard model background expectation in overall number of events, comparisons of distributions of many kinematic variables, and finally comparisons on the tails of distributions that sum the momenta of the objects in an event. With 1.07 fb-1 at the D0 experiment, we find no evidence of physics beyond the standard model. Several discrepancies from the standard model were found, but none of these provide a compelling case for new physics.

  8. pK{sup +}Λ final state: Towards the extraction of the ppK{sup −} contribution

    Energy Technology Data Exchange (ETDEWEB)

    Fabbietti, L., E-mail: laura.fabbietti@ph.tum.de [Excellence Cluster ‘Origin and Structure of the Universe’, 85748 Garching (Germany); Agakishiev, G. [Joint Institute of Nuclear Research, 141980 Dubna (Russian Federation); Behnke, C. [Institut für Kernphysik, Goethe-Universität, 60438 Frankfurt (Germany); Belver, D. [LabCAF, F. Física, Univ. de Santiago de Compostela, 15706 Santiago de Compostela (Spain); Belyaev, A. [Joint Institute of Nuclear Research, 141980 Dubna (Russian Federation); Berger-Chen, J.C. [Excellence Cluster ‘Origin and Structure of the Universe’, 85748 Garching (Germany); Blanco, A. [LIP-Laboratório de Instrumentação e Física Experimental de Partículas, 3004-516 Coimbra (Portugal); Blume, C. [Institut für Kernphysik, Goethe-Universität, 60438 Frankfurt (Germany); Böhmer, M. [Physik Department E12, Technische Universität München, 85748 Garching (Germany); Cabanelas, P. [LabCAF, F. Física, Univ. de Santiago de Compostela, 15706 Santiago de Compostela (Spain); Chernenko, S. [Joint Institute of Nuclear Research, 141980 Dubna (Russian Federation); Dritsa, C. [II. Physikalisches Institut, Justus Liebig Universität Giessen, 35392 Giessen (Germany); Dybczak, A. [Smoluchowski Institute of Physics, Jagiellonian University of Cracow, 30-059 Kraków (Poland); and others

    2013-09-20

    The reaction p(@3.5 GeV)+p→p+Λ+K{sup +} can be studied to search for the existence of kaonic bound states like ppK{sup −} leading to this final state. This effort has been motivated by the assumption that in p+p collisions the Λ(1405) resonance can act as a doorway to the formation of the kaonic bound states. The status of this analysis within the HADES Collaboration, with particular emphasis on the comparison to simulations, is shown in this work and the deviation method utilized by the DISTO Collaboration in a similar analysis is discussed. The outcome suggests the employment of a partial wave analysis do disentangle the different contributions to the measured pK{sup +}Λ final state.

  9. Identifying the optimal depth for mussel suspended culture in shallow and turbid environments

    Science.gov (United States)

    Filgueira, Ramón; Grant, Jon; Petersen, Jens Kjerulf

    2018-02-01

    Bivalve aquaculture is commonly carried out in shallow water systems, which are susceptible to resuspension of benthic particulate matter by natural processes such as tidal currents, winds and wave action, as well as human activity. The resuspended material can alter the availability of food particles for cultured bivalves. The effect of resuspended material on bivalve bioenergetics and growth is a function of the quality and concentration of resuspended particles and background diet in the water column. Given the potential for positive or negative impacts on bivalve growth and consequently on farm productivity, farmers must position the cultured biomass at the appropriate depth to benefit from or mitigate the impact of this resuspended material. A combination of field measurements, a 1-D vertical resuspension model and a bioenergetic model for mussels based on Dynamic Energy Budget (DEB) theory has been carried out for a mussel farm in Skive Fjord, a shallow Danish fjord, with the aim of identifying the optimal depth for culture. Observations at the farm location revealed that horizontal advection is more important than vertical resuspension during periods with predominant Eastern winds. In addition, high background seston in the water column reduces the impact of resuspension on the available food for mussels. The simulation of different scenarios in terms of food availability suggested minimal effects of resuspension on mussel growth. Based on this finding and the fact that phytoplankton concentration, the main food source for mussels, is usually higher in the upper part of the water column, suspended culture in the top 3 m of the water column seems to be the optimal practice to produce mussels in Skive Fjord.

  10. Comparison of conventional technology and radiation technology. Final report for the period 1 June 1988 - 31 May 1989

    Energy Technology Data Exchange (ETDEWEB)

    Czvikovszky, T [Research Inst. for the Plastic Industry, Budapest (Hungary)

    1990-12-31

    The project consisted of three parts in which comparison of conventional technology and radiation technology of composite materials was aimed, in the field of impregnated wood-plastics, wood fiber reinforced/filled plastics and UV and EB coated wood products. The report includes 4 papers presented at different meetings. Refs, figs and tabs.

  11. Comparison of conventional technology and radiation technology. Final report for the period 1 June 1988 - 31 May 1989

    International Nuclear Information System (INIS)

    Czvikovszky, T.

    1989-01-01

    The project consisted of three parts in which comparison of conventional technology and radiation technology of composite materials was aimed, in the field of impregnated wood-plastics, wood fiber reinforced/filled plastics and UV and EB coated wood products. The report includes 4 papers presented at different meetings. Refs, figs and tabs

  12. PILOT STUDY: Report on the CCPR Pilot Comparison: Spectral Responsivity 10 nm to 20 nm

    Science.gov (United States)

    Scholze, Frank; Vest, Robert; Saito, Terubumi

    2010-01-01

    The CCPR Pilot Comparison on spectral responsivity in the 10 nm to 20 nm spectral range was carried out within the framework of the CIPM Mutual Recognition Arrangement by three laboratories: PTB (Germany), NIST (USA), and NMIJ/AIST (Japan) with PTB acting as the central and reporting laboratory. All participating laboratories used monochromatized synchrotron radiation. PTB and NIST used a cryogenic radiometer as the primary standard detector and NMIJ, an ionization chamber with extrapolation by a wavelength-independent detector. The aim of the pilot comparison was to check the accuracy of the radiometric scale of spectral responsivity in the short wavelength EUV spectral range which has recently gained in technological importance. The wavelengths of measurement were from 11.5 nm to 20 nm in 0.5 nm steps and additionally 12.2 nm. The comparison was carried out through the calibration of a group of transfer standard detectors. Two sets of three diodes of types AXUV and SXUV from International Radiation Detectors, Inc. were used for the comparison. The comparison had the form of a star comparison: Pilot-lab A-pilot-lab B-pilot, PTB acting as the pilot laboratory. All results were communicated directly to the pilot laboratory. The report describes in detail the measurements made at PTB and summarizes the reports submitted by the participants. Measurements carried out by the pilot laboratory before and after the circulation of the detectors proved that the stability of the detectors was sufficient for the comparison. For the type AXUV detectors, however, changes in their responsivity contributed to the uncertainty of the comparison. Measurement results from participants and their associated uncertainties were analyzed in this report according to the Guidelines for CCPR Comparison Report Preparation. The uncertainty contributions were separated, as to whether they are wavelength dependent or not. All bilateral DoE are well within the respective k = 2 expanded uncertainty

  13. PATHWAY: a dynamic foodchain model to predict radionuclide ingestion after fallout deposition. Final report, September 17, 1979-December 31, 1985

    International Nuclear Information System (INIS)

    Whicker, F.W.; Kirchner, T.B.

    1986-01-01

    This paper describes the structure and basis for parameter values of a computerized foodchain transport model for radionuclides. The model, called ''PATHWAY,'' estimates the time-integrated intake by humans of twenty radionuclides after a single deposition of radioactive material from the atmosphere to the landscape. The model solves a set of differential equations to estimate the inventories and concentrations of radionuclides in three soil layers and numerous types of vegetation, animal tissues and animal products as a function of time following a deposition event. Dynamic processes considered in the model include foliar interception, weathering and absorption; plant growth, uptake, harvest and senescence; soil resuspension, percolation, leaching and tillage; radioactive decay; livestock ingestion, absorption, excretion; and etc. An age- and sex-specific human diet is embodied in the model to permit calculation of time-dependent radionuclide ingestion rates, which are then numerically integrated. 3 figs., 10 tabs

  14. Bilateral comparison of 1 V and 10 V standards between the DEFNAT (Tunisia) and the BIPM February to March 2016 (part of the ongoing BIPM key comparison BIPM.EM-K11.a and b)

    Science.gov (United States)

    Solve, S.; Chayramy, R.; Ben Salah, B.; Mallat, A.; Abene, L.; Stock, M.

    2016-01-01

    As part of the ongoing BIPM key comparison BIPM.EM-K11.a and b, a comparison of the 1 V and 10 V voltage reference standards of the BIPM and the Laboratoire de Métrologie Electrique, DEFNAT (Tunisia), was carried out from February to March 2016. Two BIPM Zener diode-based travelling standards (Fluke 732B), BIPMC (ZC) and BIPM6 (Z6), were transported by freight to DEFNAT and back to BIPM. In order to keep the Zeners powered during their transportation phase, a BIPM in-house voltage stabiliser was connected in parallel to the internal battery. The voltage stabiliser consists of a set of two batteries, electrically protected from surcharge-discharge, easy to recharge and is designed to power two transfer standards for 10 consecutive days. At DEFNAT, the reference standard for DC voltage is a Josephson Voltage Standard. The output EMF (Electromotive Force) of each travelling standard was measured by direct comparison with the primary standard. At the BIPM, the travelling standards were calibrated, before and after the measurements at DEFNAT, with the Josephson Voltage Standard. Results of all measurements were corrected for the dependence of the output voltages of the Zener standards on internal temperature and ambient atmospheric pressure. The final result of the comparison is presented as the difference between the values assigned to DC voltage standards by DEFNAT, at the level of 1.018 V and 10 V, at DEFNAT, UDEFNAT, and those assigned by the BIPM, at the BIPM, UBIPM, at the reference date of the 26th of February 2016. UDEFNAT - UBIPM = + 0.07 μV uc = 0.04 μV, at 1.018 V UDEFNAT - UBIPM = + 0.38 μV uc = 0.10 μV, at 10 V where uc is the combined standard uncertainty associated with the measured difference, including the uncertainty of the representation of the volt at the BIPM and at NSAI-NML, based on KJ-90, and the uncertainty related to the comparison. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which

  15. Distribution of hydrogen within the HDR-containment under severe accident conditions. OECD standard problem. Final comparison report

    Energy Technology Data Exchange (ETDEWEB)

    Karwat, H

    1992-08-15

    The present report summarizes the results of the International Standard Problem Exercise ISP-29, based on the HDR Hydrogen Distribution Experiment E11.2. Post-test analyses are compared to experimentally measured parameters, well-known to the analysis. This report has been prepared by the Institute for Reactor Dynamics and Reactor Safety of the Technical University Munich under contract with the Gesellschaft fuer Anlagen- und Reaktorsicherheit (GRS) which received funding for this activity from the German Ministry for Research and Technology (BMFT) under the research contract RS 792. The HDR experiment E11.2 has been performed by the Kernforschungszentrum Karlsruhe (KfK) in the frame of the project 'Projekt HDR-Sicherheitsprogramm' sponsored by the BMFT. Ten institutions from eight countries participated in the post-test analysis exercise which was focussing on the long-lasting gas distribution processes expected inside a PWR containment under severe accident conditions. The gas release experiment was coupled to a long-lasting steam release into the containment typical for an unmitigated small break loss-of-coolant accident. In lieu of pure hydrogen a gas mixture consisting of 15% hydrogen and 85% helium has been applied in order to avoid reaching flammability during the experiment. Of central importance are common overlay plots comparing calculated transients with measurements of the global pressure, the local temperature-, steam- and gas concentration distributions throughout the entire HDR containment. The comparisons indicate relatively large margins between most calculations and the experiment. Having in mind that this exercise was specified as an 'open post-test' analysis of well-known measured data the reasons for discrepancies between measurements and simulations were extensively discussed during a final workshop. It was concluded that analytical shortcomings as well as some uncertainties of experimental boundary conditions may be responsible for deviations

  16. Distribution of hydrogen within the HDR-containment under severe accident conditions. OECD standard problem. Final comparison report

    International Nuclear Information System (INIS)

    Karwat, H.

    1992-08-01

    The present report summarizes the results of the International Standard Problem Exercise ISP-29, based on the HDR Hydrogen Distribution Experiment E11.2. Post-test analyses are compared to experimentally measured parameters, well-known to the analysis. This report has been prepared by the Institute for Reactor Dynamics and Reactor Safety of the Technical University Munich under contract with the Gesellschaft fuer Anlagen- und Reaktorsicherheit (GRS) which received funding for this activity from the German Ministry for Research and Technology (BMFT) under the research contract RS 792. The HDR experiment E11.2 has been performed by the Kernforschungszentrum Karlsruhe (KfK) in the frame of the project 'Projekt HDR-Sicherheitsprogramm' sponsored by the BMFT. Ten institutions from eight countries participated in the post-test analysis exercise which was focussing on the long-lasting gas distribution processes expected inside a PWR containment under severe accident conditions. The gas release experiment was coupled to a long-lasting steam release into the containment typical for an unmitigated small break loss-of-coolant accident. In lieu of pure hydrogen a gas mixture consisting of 15% hydrogen and 85% helium has been applied in order to avoid reaching flammability during the experiment. Of central importance are common overlay plots comparing calculated transients with measurements of the global pressure, the local temperature-, steam- and gas concentration distributions throughout the entire HDR containment. The comparisons indicate relatively large margins between most calculations and the experiment. Having in mind that this exercise was specified as an 'open post-test' analysis of well-known measured data the reasons for discrepancies between measurements and simulations were extensively discussed during a final workshop. It was concluded that analytical shortcomings as well as some uncertainties of experimental boundary conditions may be responsible for deviations

  17. Storage of human platelets by freezing

    Energy Technology Data Exchange (ETDEWEB)

    Kim, B K; Tanoue, K; Baldini, M G

    1976-01-01

    Prolonged, probably indefinite storage of viable and functional human platelets is now possible by freezing with dimethylsulfoxide (DMSO). The platelets have a nearly normal survival upon reinfusion and are capable of sustained hemostatic effectiveness in thrombocytopenic patients. Adaptation of the freezing technique for large-scale usage has more recently been achieved. The method is mainly based on the following principles: (1) use of plasma for suspension of the platelet concentrate; (2) gradual addition (0.5% every 2 min) of DMSO to a final concentration of 5% and its gradual removal; (3) a slow cooling rate of about 1/sup 0/C per min and rapid thawing (in 1 min); (4) use of a polyolefin plastic bag for freezing; (5) a washing medium of 20% plasma in Hanks' balanced salt solution; (6) final resuspension of the platelets in 50% plasma in Hanks' solution.

  18. Experimental Method for Measuring Dust Load on Surfaces in Rooms

    DEFF Research Database (Denmark)

    Lengweiler, Philip; Nielsen, Peter V.; Moser, Alfred

    A new experimental setup to investigate the physical process of dust deposition and resuspension on and from surfaces is introduced. Dust deposition can reduce the airborne dust concentration considerably. As a basis for developing methods to eliminate dust-related problems in rooms, there is a n......A new experimental setup to investigate the physical process of dust deposition and resuspension on and from surfaces is introduced. Dust deposition can reduce the airborne dust concentration considerably. As a basis for developing methods to eliminate dust-related problems in rooms......, there is a need for better understanding of the mechanism of dust deposition and resuspension. With the presented experimental setup, the dust load on surfaces in a channel can be measured as a function of the environmental and surface conditions and the type of particles under controlled laboratory conditions....

  19. The dispersion of radioactive aerosols in fires

    International Nuclear Information System (INIS)

    Buijs, K.; Chavane de Dalmassy, B.; Pickering, S.

    1989-01-01

    Experimental results are reported on the resuspension, due to fire, of radioactive nuclear fuel particles from a variety of substrates. Experiments were carried out both on large and small scale. In small-scale fires uranium-plutonium oxide particles were used and in the large-scale fires cerium-europium oxide particles were used. The mechanisms of particle resuspension were investigated in separate series of experiments. It was found that in small-scale fires up to 20% of the particle inventory can be resuspended and in large-scale fires up to 75%. In both cases most of the resuspended material deposits within the fire chamber and a maximum of 2% is carried into the ventilation duct at the outlet of the fire chamber. The predominant resuspension mechanisms are bubble bursting in small-scale fires and turbulence in large-scale fires. (orig.)

  20. Key comparison BIPM.RI(I)-K5 of the air kerma standards of the ININ, Mexico and the BIPM in 137Cs gamma radiation

    Science.gov (United States)

    Kessler, C.; Burns, D. T.; Alvarez Romero, J. T.; De la Cruz Hernández, D.; Cabrera Vertti, M. R.; Tovar-Muñoz, V. M.

    2015-01-01

    A direct comparison of the standards for air kerma of the Instituto Nacional de Investigaciones Nucleares (ININ), Mexico, and of the Bureau International des Poids et Mesures (BIPM) was carried out in the 137Cs radiation beam of the BIPM in February 2015. The comparison result, evaluated as a ratio of the ININ and the BIPM standards for air kerma, is 1.0048 with a combined standard uncertainty of 2.0 × 10-3. The results are analysed and presented in terms of degrees of equivalence for entry in the BIPM key comparison database. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCRI, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

  1. Adoption of information technology in primary care physician offices in New Zealand and Denmark, part 5: final comparisons

    Directory of Open Access Journals (Sweden)

    Denis Protti

    2009-03-01

    Full Text Available This is the last in a series of five papers about the use of computing technology in general practitioner (GP practices in Denmark and New Zealand. This paper introduces a unique comparison instrument developed for this study using the best evidence available namely data was pulled from centralised databases and was indisputable (e.g. percentage of primary care physicians who send medication prescriptions electronically to pharmacies. Where the data was simply not available, estimates were made. Since the reliability of the data on the use of computers by primary care physicians is so variable and in some case simply not available, the authors also introduce the use of a Cochrane-like confidence factor (CF to each comparison measure. The paper draws particular attention to the fact that both countries have a highly visible central unifying body or what might be called a Health System Integrator; though Denmark s Medcom is a pseudo government agency New Zealand's HealthLink is a private company, both play critical roles in the success story of these two countries.

  2. Schedulability Analysis for Java Finalizers

    DEFF Research Database (Denmark)

    Bøgholm, Thomas; Hansen, Rene Rydhof; Søndergaard, Hans

    2010-01-01

    Java finalizers perform clean-up and finalisation of objects at garbage collection time. In real-time Java profiles the use of finalizers is either discouraged (RTSJ, Ravenscar Java) or even disallowed (JSR-302), mainly because of the unpredictability of finalizers and in particular their impact...... on the schedulability analysis. In this paper we show that a controlled scoped memory model results in a structured and predictable execution of finalizers, more reminiscent of C++ destructors than Java finalizers. Furthermore, we incorporate finalizers into a (conservative) schedulability analysis for Predictable Java...... programs. Finally, we extend the SARTS tool for automated schedulability analysis of Java bytecode programs to handle finalizers in a fully automated way....

  3. Bilateral comparison of 1 V and 10 V standards between the NMISA (South Africa) and the BIPM April to June 2017 (part of the ongoing BIPM key comparison BIPM.EM-K11.a and b)

    Science.gov (United States)

    Solve, S.; Chayramy, R.; Matlejoane, A. M.; Magagula, L.; Stock, M.

    2018-01-01

    As part of the ongoing BIPM key comparison BIPM.EM-K11.a and b, a comparison of the 1.018 V and 10 V voltage reference standards of the BIPM and the National Metrology Institute of South Africa, NMISA (South Africa), was carried out from April to June 2017. Two BIPM Zener diode-based travelling standards (Fluke 732B), BIPMA (ZA) and BIPMB (ZB), were transported by freight to NMISA and back to BIPM. In order to keep the Zeners powered during their transportation phase, a voltage stabilizer developed by BIPM was connected in parallel to the internal battery. It consists of a set of two batteries, electrically protected from surcharge-discharge, easy to recharge and is designed to power two transfer standards for ten consecutive days. At NMISA, the reference standard for DC voltage is a Josephson Voltage Standard. The output EMF (Electromotive Force) of each travelling standard was measured by direct comparison with the primary standard. At the BIPM, the travelling standards were calibrated, before and after the measurements at NMISA, with the Josephson Voltage Standard. Results of all measurements were corrected for the dependence of the output voltages of the Zener standards on internal temperature and atmospheric pressure. The final result of the comparison is presented as the difference between the values assigned to DC voltage standards by NMISA, at the level of 1.018 V and 10 V, at NMISA, UNMISA, and those assigned by the BIPM, at the BIPM, UBIPM, at the reference dates of the 19th and 18th of May 2017, respectively. UNMISA - UBIPM = + 0.07 μV uc = 0.02 μV, at 1.018 V UNMISA - UBIPM = + 0.001 μV uc = 0.34 μV, at 10 V where uc is the combined standard uncertainty associated with the measured difference, including the uncertainty of the representation of the volt at the BIPM and at NMISA, based on KJ-90, and the uncertainty related to the comparison. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which

  4. EURAMET.M.P-S9: comparison in the negative gauge pressure range -950 to 0 hPa

    Science.gov (United States)

    Saxholm, S.; Otal, P.; AltintaS, A.; Bermanec, L. G.; Durgut, Y.; Hanrahan, R.; Kocas, I.; Lefkopoulos, A.; Pražák, D.; Sandu, I.; Åetina, J.; Spohr, I.; Steindl, D.; Tammik, K.; Testa, N.

    2016-01-01

    A comparison in the negative gauge pressure range was arranged in the period 2011 - 2012. A total of 14 laboratories participated in this comparison: BEV (Austria), CMI (Czech Republic), DANIAmet-FORCE (Denmark), EIM (Greece), HMI/FSB-LPM (Croatia), INM (Romania), IPQ (Portugal), LNE (France), MCCAA (Malta), METROSERT (Estonia), MIKES (Finland), MIRS/IMT/LMT (Slovenia), NSAI (Ireland) and UME (Turkey). The project was divided into two loops: Loop1, piloted by MIKES, and Loop2, piloted by LNE. The results of the two loops are reported separately: Loop1 results are presented in this paper. The transfer standard was Beamex MC5 no. 25516865 with internal pressure module INT1C, resolution 0.01 hPa. The nominal pressure range of the INT1C is -1000 hPa to +1000 hPa. The nominal pressure points for the comparison were 0 hPa, -200 hPa, -400 hPa, -600 hPa, -800 hPa and -950 hPa. The reference values and their uncertainties as well as the difference uncertainty between the laboratory results and the reference values were determined from the measurement data by Monte Carlo simulations. Stability uncertainty of the transfer standard was included in the final difference uncertainty. Degrees of equivalences and mutual equivalences between the laboratories were calculated. Each laboratory reported results for all twelve measurement points, which means that there were 168 reported values in total. Some 163 of the 168 values (97 %) agree with the reference values within the expanded uncertainties, with a coverage factor k = 2. Among the laboratories, four different methods were used to determine negative gauge pressure. It is concluded that special attention must be paid to the measurements and methods when measuring negative gauge pressures. There might be a need for a technical guide or a workshop that provides information about details and practices related to the measurements of negative gauge pressure, as well as differences between the different methods. The comparison is

  5. What works with worked examples: Extending self-explanation and analogical comparison to synthesis problems

    Science.gov (United States)

    Badeau, Ryan; White, Daniel R.; Ibrahim, Bashirah; Ding, Lin; Heckler, Andrew F.

    2017-12-01

    The ability to solve physics problems that require multiple concepts from across the physics curriculum—"synthesis" problems—is often a goal of physics instruction. Three experiments were designed to evaluate the effectiveness of two instructional methods employing worked examples on student performance with synthesis problems; these instructional techniques, analogical comparison and self-explanation, have previously been studied primarily in the context of single-concept problems. Across three experiments with students from introductory calculus-based physics courses, both self-explanation and certain kinds of analogical comparison of worked examples significantly improved student performance on a target synthesis problem, with distinct improvements in recognition of the relevant concepts. More specifically, analogical comparison significantly improved student performance when the comparisons were invoked between worked synthesis examples. In contrast, similar comparisons between corresponding pairs of worked single-concept examples did not significantly improve performance. On a more complicated synthesis problem, self-explanation was significantly more effective than analogical comparison, potentially due to differences in how successfully students encoded the full structure of the worked examples. Finally, we find that the two techniques can be combined for additional benefit, with the trade-off of slightly more time on task.

  6. Final report on AFRIMETS.QM-K27: Determination of ethanol in aqueous matrix

    Science.gov (United States)

    Archer, Marcellé; Fernandes-Whaley, Maria; Visser, Ria; de Vos, Jayne; Prins, Sara; Rosso, Adriana; Ruiz de Arechavaleta, Mariana; Tahoun, Ibrahim; Kakoulides, Elias; Luvonga, Caleb; Muriira, Geoffrey; Naujalis, Evaldas; Zakaria, Osman Bin; Buzoianu, Mirella; Bebic, Jelena; Achour Mounir, Ben; Thanh, Ngo Huy

    2013-01-01

    Level 1; four of the ten participating laboratories submitted mean results within 1.5% of the gravimetric reference value for Level 2. Two of the participating laboratories achieved mean results within 1.5% of the gravimetric reference value for both levels. Participants in the AFRIMETS-K27 study would therefore have benefited from a pilot study in which to test their measurement capability prior to participation in the key comparison. Several NMIs, however, will still be able to make new CMC claims based on their performance in this comparison. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

  7. DIMEC - Final Report

    DEFF Research Database (Denmark)

    Conrad, Finn

    1997-01-01

    Final report of the research project DIMEC - Danish InfoMechatronic Control supported by the Danish Technical Research Council, STVF.......Final report of the research project DIMEC - Danish InfoMechatronic Control supported by the Danish Technical Research Council, STVF....

  8. Final Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    Glasser, Alan H. [Fusion Theory and Computation Inc., Kingston, WA (United States)

    2018-02-02

    Final technical report on DE-SC0016106. This is the final technical report for a portion of the multi-institutional CEMM project. This report is centered around 3 publications and a seminar presentation, which have been submitted to E-Link.

  9. We can do it: the interplay of construal orientation and social comparisons under threat.

    Science.gov (United States)

    Marx, David M; Stapel, Diederik A; Muller, Dominique

    2005-03-01

    The authors investigated how a collective self-construal orientation in combination with positive social comparisons "turns off" the negative effects of stereotype threat. Specifically, Experiment 1 demonstrated that stereotype threat led to increased accessibility of participants' collective self ("we"). Experiment 2 showed that this feeling of "we-ness" in the stereotype threat condition centered on the participants' stereotyped group membership and not on other important social groups (e.g., students). Experiment 3 indicated that in threat situations, when participants' collective self is accessible, positive social comparison information led to improved math test performance and less concern, whereas in nonthreat situations, when the collective self is less accessible, positive comparison information led to worse test performance and more concern. Our final experiment revealed that under stereotype threat, only those comparison targets who are competent in the relevant domain (math), rather than in domains unrelated to math (athletics), enhanced participants' math test performance. ((c) 2005 APA, all rights reserved).

  10. Participation in the international comparison of probabilistic consequence assessment codes organized by OECD/NEA and CEC. Final Report

    International Nuclear Information System (INIS)

    Rossi, J.

    1994-02-01

    Probabilistic Consequence Assessment (PCA) methods are exploited not only in risk evaluation but also to study alternative design features, reactor siting recommendations and to obtain acceptable dose criteria by the radiation safety authorities. The models are programmed into computer codes for these kind of assessment. To investigate the quality and competence of different models, OECD/NEA and CEC organized the international code comparison exercise, which was participated by the organizations from 15 countries. There were seven codes participating in the exercise. The objectives of the code comparison exercise were to compare the results by the codes, to contribute to PCA code quality assurance, to harmonize the codes, to provide a forum for discussion on various approaches and to produce the report on the exercise. The project started in 1991 and the results of the calculations were completed in autumn 1992. The international report consists of two parts: the Overview Report for decision makers and the supporting detailed Technical Report. The results of the project are reviewed as an user of the ARANO-programme of VTT and trends of it's further development are indicated in this report. (orig.) (11 refs., 13 figs., 4 tabs.)

  11. Development of a resupension model for contaminated soils: Application to the Palomares area

    International Nuclear Information System (INIS)

    Garcia-Olivares, A.

    1993-01-01

    A model is presented which has been used to simulate the wind resuspension and transport of contaminated soil in the area surrounding the Palomares village, in Southern Spain. The model uses site specific data and some generic parameters as resuspension rate and deposition velocity. The model is able to predict the order of magnitude of the observed air concentration of activity. Some lines of research are suggested which could improve the understanding of the phenomena involved. (author)

  12. Evaluating airborne radionuclide concentrations in the tank farms

    International Nuclear Information System (INIS)

    Gleckler, B.P.

    1993-01-01

    The objective of this study is to determine, through the collection of grab sampling data, that an in-depth resuspension study should or should not be performed. Currently there is not enough data available to determine if a potential health hazard exists due to resuspended contamination in the tank farms. A detailed resuspension study is currently not justified, because the limited quantity of air sample data collected does not indicate the existence of a potential health hazard

  13. Visualization problems in conductor thermal aging resp. comparison of matlab and gnuplot graphical outputs

    International Nuclear Information System (INIS)

    Beza, J.; Heckenbergerova, J.

    2012-01-01

    The main aim of this paper is comparison of Matlab and Gnuplot software suitability for visualization of results in electro energetic and electro engineering domain. Whole contribution is targeted on specific graphical outputs in problematic of thermal aging of overhead power transmission lines. First, all graphical outputs determined for comparison are visualized in Matlab and furthermore strengths and disadvantages of this implementation are described. Same graphics are then created by free software Gnuplot and finally comparison of both visualization software is made. Last part of the contribution contains main rules and tips about Gnuplot visualization and can be used as User Handbook. The major target of this contribution is to show advantages and shortcomings of Matlab graphical outputs together with introduction of Gnuplot software and suitable alternative for visualization of electrotechnical results. (Authors)

  14. Environmental and health effects review for obscurant graphite flakes. Final report, 1991 July--1993 May

    Energy Technology Data Exchange (ETDEWEB)

    Driver, C.J.; Ligotke, M.W.; Landis, W.G.; Downs, J.L.; Tiller, B.L.; Moore, E.B. Jr.; Cataldo, D.A.

    1993-07-01

    The health and environmental effects of obscurant graphite flakes were reviewed and compared to predicted levels of graphite flake material in the field during typical testing and training scenarios. Graphite flake dispersion and deposition for simulated mechanical and pyrotechnic releases were determined using a modified Gaussian atmospheric plume-dispersion model. The potential for wind resuspension of graphite flakes is controlled by weathering processes and incorporation rates in soil. Chemically, graphite flakes pose little risk to aquatic or terrestrial systems. Mechanical damage to plants and invertebrate and vertebrate organisms from the flakes is also minimal. In humans, the pathological and physiological response to inhaled graphite flake is similar to that induced by nuisance dusts and cause only transient pulmonary changes. Repeated exposure to very high concentrations (such as those near the source generator) may overwhelm the clearance mechanisms of the lung and result in pulmonary damage from the retained particles in unprotected individuals. However, these lesions either resolve with time or are of limited severity. Health effects of mixed aerosols of mixed aerosols of graphite and fog oil are similar to those produced by graphite flakes alone. Environmental impacts of fog oil-coated graphite flakes are not well known.

  15. Airborne plutonium transported during southwesterly winds near the Hanford Prosser Barricade

    International Nuclear Information System (INIS)

    Sehmel, G.A.

    1980-01-01

    Airborne plutonium could result from resuspension of nuclear-weapons-testing stratospheric fallout deposition. To determine this possible resuspension at the Hanford site, two field experiments between April 12 to june 29, 1976 and August 12, 1976 to January 11, 1977 were conducted near the Prosser Barricade in the Hanford area about 19 to 22 km southeast (140 0 to 160 0 ) of the fuel-processing areas. The primary objective of these experimentss was to determine if stratospheric fallout resuspension was reflected by airborne plutonium concentrations increasing with increasing wind speed. A secondary objective was to confirm the source of the airborne plutonium by determining the plutonium-240 isotopic content or the plutonium-240/plutonium-239-mass ratio. Stratospheric fallout can be identified by the ratio of 240 Pu to other plutonium isotopes in surface soils. Plutonium was transported during southwesterly winds during the two study periods at the Prosser Barricade. Airborne 239 240 Pu concentrations varied as powers of wind speed (U):U -0 2 to U 7 8 . The airborne solids content ranged from 6 x 10 -8 to 1.7 x 10 -6 μCi/g. The 240 Pu isotopic content ranged from 5.6 to 8.1 atom percent and the 240 Pu/ 239 Pu mass ratio ranged from 0.065 to 0.089. The estimated fraction of stratospheric fallout plutonium in these samples was less than 0.24. The remaining airborne plutonium was probably of Hanford origin. Airborne plutonium probably represents resuspension of plutonium from undetermined sites by mechanisms and events not clear at present. An increasing airborne plutonium concentration with increasing wind speed might be expected for an upwind resuspension source(s). However, the geographical source(s) location was not investigated in this study

  16. The impact of precipitation evaporation on the atmospheric aerosol distribution in EC-Earth v3.2.0

    Science.gov (United States)

    de Bruine, Marco; Krol, Maarten; van Noije, Twan; Le Sager, Philippe; Röckmann, Thomas

    2018-04-01

    The representation of aerosol-cloud interaction in global climate models (GCMs) remains a large source of uncertainty in climate projections. Due to its complexity, precipitation evaporation is either ignored or taken into account in a simplified manner in GCMs. This research explores various ways to treat aerosol resuspension and determines the possible impact of precipitation evaporation and subsequent aerosol resuspension on global aerosol burdens and distribution. The representation of aerosol wet deposition by large-scale precipitation in the EC-Earth model has been improved by utilising additional precipitation-related 3-D fields from the dynamical core, the Integrated Forecasting System (IFS) general circulation model, in the chemistry and aerosol module Tracer Model, version 5 (TM5). A simple approach of scaling aerosol release with evaporated precipitation fraction leads to an increase in the global aerosol burden (+7.8 to +15 % for different aerosol species). However, when taking into account the different sizes and evaporation rate of raindrops following Gong et al. (2006), the release of aerosols is strongly reduced, and the total aerosol burden decreases by -3.0 to -8.5 %. Moreover, inclusion of cloud processing based on observations by Mitra et al. (1992) transforms scavenged small aerosol to coarse particles, which enhances removal by sedimentation and hence leads to a -10 to -11 % lower aerosol burden. Finally, when these two effects are combined, the global aerosol burden decreases by -11 to -19 %. Compared to the Moderate Resolution Imaging Spectroradiometer (MODIS) satellite observations, aerosol optical depth (AOD) is generally underestimated in most parts of the world in all configurations of the TM5 model and although the representation is now physically more realistic, global AOD shows no large improvements in spatial patterns. Similarly, the agreement of the vertical profile with Cloud-Aerosol Lidar with Orthogonal Polarization (CALIOP

  17. Retrieval of fluidizable radioactive wastes from storage facilities

    International Nuclear Information System (INIS)

    2006-08-01

    This report provides guidance for strategic planning and implementation of resuspension and retrieval of stored fluid or fluidizable radioactive wastes. The potential risks associated with preparation and realization of these processes are included in the report, and lessons learned from previous applications are highlighted. Technological procedures and equipment used in various countries for resuspension and remobilization of stored fluidizable radioactive wastes are described in the attached annexes as potential options. Waste retrieval is a maturing technology of major importance now that Member States are moving forward in the responsible management of wastes by removal to safe interim storage or disposal. Retrieval of fluidizable wastes is a four-phase operation: (1) access to the waste, (2) mobilize the waste, (3) remove the waste; and (4) transfer the waste.This report divides successful retrieval of radioactive waste into two areas. The first area applies the concept of the waste retrieval as being the final component of a systematic process of old waste management. It also encompasses characterization as it applies to waste retrieval and downstream processes, including acceptance of wastes for treatment, conditioning, storage or disposal. It should be in conformity with national policy, as well as complying with international safety standards and environmental agreements. The second area of the report focuses on implementation of waste retrieval in a wide range of scenarios and using a wide range of retrieval approaches, equipment and technologies. Technical processes are further explained as part of the experience gained in advanced countries on the subject. A set of detailed retrieval technology descriptions by country is included as Annexes to this report. Thirteen experts from seven Member States that previously implemented, or have planned for the near future, significant resuspension and remobilization operations were involved in the preparation of

  18. Bilateral key comparison SIM.T-K6.5 on humidity standards in the dew/frost-point temperature range from -30 °C to +20 °C

    Science.gov (United States)

    Meyer, C.; Solano, A.

    2016-01-01

    A Regional Metrology Organization (RMO) Key Comparison of dew/frost point temperatures was carried out by the National Institute of Standards and Technology (NIST, USA) and the Laboratorio Costarricense de Metrología (LACOMET, Costa Rica) between February 2015 and August 2015. The results of this comparison are reported here, along with descriptions of the humidity laboratory standards for NIST and LACOMET and the uncertainty budget for these standards. This report also describes the protocol for the comparison and presents the data acquired. The results are analyzed, determining degree of equivalence between the dew/frost-point standards of NIST and LACOMET. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCT, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

  19. Bilateral key comparison SIM.T-K6.2 on humidity standards in the dew/frost-point temperature range from -20 °c to 20 °c

    Science.gov (United States)

    Huang, P. H.; Meyer, C. W.; Martines-López, E.; Dávila Pacheco, J. A.; Méndez-Lango, E.

    2014-01-01

    A Regional Metrology Organization (RMO) Key Comparison of dew/frost point temperatures was carried out by the National Institute of Standards and Technology (NIST, USA) and the Centro Nacional de Metrologia (CENAM, Mexico) between July 2008 and December 2008. The results of this comparison are reported here, along with descriptions of the humidity laboratory standards for NIST and CENAM and the uncertainty budget for these standards. This report also describes the protocol for the comparison and presents the data acquired. The results are analyzed, determining degree of equivalence between the dew/frost-point standards of NIST and CENAM. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCT, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

  20. Concept and Idea-Project for Yugoslav Low and Intermediate level Radioactive Waste Materials Final Disposal Facility

    International Nuclear Information System (INIS)

    Peric, A.

    1997-01-01

    Encapsulation of rad waste in a mortar matrix and displacement of such solidified waste forms into the shallow land burial system, engineered trench system type is suggested concept for the final disposal of low and intermediate level rad waste. The mortar-rad waste mixtures are cured in containers of either concrete or metal for an appropriate period of time, after which solidified rad waste-mortar monoliths are then placed in the engineered trench system, parallelepiped honeycomb structure. Trench consists of vertical barrier-walls, bottom barrier-floors, surface barrier-caps and permeable-reactive walls. Surroundings of the trench consists of buffer barrier materials, mainly clay. Each segment of the trench is equipped with the independent drainage system, as a part of the main drainage. Encapsulation of each filled trench honeycomb segment is performed with concrete cap. Completed trench is covered with impermeable plastic foil and soil leaner, preferably clay. Paper presents an overview of the final disposal facility engineered trench system type. Advantages in comparison with other types of final disposal system are given. (author)

  1. Fundamental Processes in Plasmas. Final report

    International Nuclear Information System (INIS)

    O'Neil, Thomas M.; Driscoll, C. Fred

    2009-01-01

    This research focuses on fundamental processes in plasmas, and emphasizes problems for which precise experimental tests of theory can be obtained. Experiments are performed on non-neutral plasmas, utilizing three electron traps and one ion trap with a broad range of operating regimes and diagnostics. Theory is focused on fundamental plasma and fluid processes underlying collisional transport and fluid turbulence, using both analytic techniques and medium-scale numerical simulations. The simplicity of these systems allows a depth of understanding and a precision of comparison between theory and experiment which is rarely possible for neutral plasmas in complex geometry. The recent work has focused on three areas in basic plasma physics. First, experiments and theory have probed fundamental characteristics of plasma waves: from the low-amplitude thermal regime, to inviscid damping and fluid echoes, to cold fluid waves in cryogenic ion plasmas. Second, the wide-ranging effects of dissipative separatrices have been studied experimentally and theoretically, finding novel wave damping and coupling effects and important plasma transport effects. Finally, correlated systems have been investigated experimentally and theoretically: UCSD experients have now measured the Salpeter correlation enhancement, and theory work has characterized the 'guiding center atoms of antihydrogen created at CERN

  2. Report to the CCT on COOMET comparison COOMET.T-K3.1 (previously COOMET.T-S1): Key regional comparison of the national standards of temperature in the range from the triple point of water to the freezing point of zinc

    Science.gov (United States)

    Pokhodun, A. I.

    2010-01-01

    In the framework of the CIPM MRA, a first COOMET comparison "Comparison of the ITS-90 realizations in the range from 0.01 °C to 429.7485 °C (from the triple point of water to the freezing point of zinc)", registered in the KCDB under the identifier "COOMET.T-K3", was carried out in 2005-2007. Four national metrology institutes took part in this comparison: VNIIM (Russian Federation), SMU (Slovakia), BelGIM (Republic of Belarus) and NSC IM (Ukraine), and two of them (VNIIM and SMU) ensured the linkage with key comparisons CCT-K3 and CCT-K4, in order to disseminate the metrological equivalence to the measurement standards of NSC IM and BelGIM. NSC IM, however, had to withdraw its results, and at the meeting of Technical Committee T-10 of COOMET it was decided to carry out a supplementary bilateral comparison between VNIIM and the NSC IM for realization of the ITS-90 in the same range of temperature. This was registered in the KCDB under the identifier COOMET.T-S1 and measurements were performed in 2008-2009. From the results presented in this report, it is possible to draw the conclusion that the COOMET supplementary comparison COOMET.T-S1 demonstrates the CMC uncertainties claimed by the NSC IM for the melting point of gallium 0.236 mK (k = 2), and the freezing points of indium 1.040 mK (k = 2), tin 0.858 mK (k = 2) and zinc 0.944 mK (k = 2). In September 2012 the Working Group on key Comparisons (WG 7) of the CCT upgraded this comparison to a COOMET key comparison of the 'CCT-K3' type. It is now identified as COOMET.T-K3.1. In April 2013 this report was superseded by item 03006 in the Technical Supplement of 2013. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCT, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

  3. KEY COMPARISON: CCEM.RF-K18.CL (GT-RF/00-1): Noise in 50 Ω coaxial line at frequencies up to 1 GHz

    Science.gov (United States)

    Eiø, Christopher; Adamson, David; Randa, James; Allal, Djamel; Uzdin, Rinadij

    2006-01-01

    A measurement comparison of noise temperature has been carried out between four national metrology laboratories in coaxial line at 30 MHz, 60 MHz and 1 GHz. The identification of this intercomparison is CCEM.RF-K18.CL. Two noise sources have been measured. The following four national laboratories participated in this intercomparison: NPL (United Kingdom), NIST (United States of America), BNM-LNE (France) and VNIIFTRI (Russia). The National Physical Laboratory (UK) acted as the pilot laboratory for the comparison. It can be seen that there is generally good agreement between the laboratories. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

  4. Microbial Remobilisation on Riverbed Sediment Disturbance in Experimental Flumes and a Human-Impacted River: Implication for Water Resource Management and Public Health in Developing Sub-Saharan African Countries.

    Science.gov (United States)

    Abia, Akebe Luther King; James, Chris; Ubomba-Jaswa, Eunice; Benteke Momba, Maggy Ndombo

    2017-03-15

    Resuspension of sediment-borne microorganisms (including pathogens) into the water column could increase the health risk for those using river water for different purposes. In the present work, we (1) investigated the effect of sediment disturbance on microbial resuspension from riverbed sediments in laboratory flow-chambers and in the Apies River, Gauteng, South Africa; and (2) estimated flow conditions for sediment-borne microorganism entrainment/resuspension in the river. For mechanical disturbance, the top 2 cm of the sediment in flow-chambers was manually stirred. Simulating sudden discharge into the river, water (3 L) was poured within 30 s into the chambers at a 45° angle to the chamber width. In the field, sediment was disturbed by raking the riverbed and by cows crossing in the river. Water samples before and after sediment disturbance were analysed for Escherichia coli. Sediment disturbance caused an increase in water E. coli counts by up to 7.9-35.8 times original values. Using Shields criterion, river-flow of 0.15-0.69 m³/s could cause bed particle entrainment; while ~1.57-7.23 m³/s would cause resuspension. Thus, sediment disturbance in the Apies River would resuspend E. coli (and pathogens), with possible negative health implications for communities using such water. Therefore, monitoring surface water bodies should include microbial sediment quality.

  5. Microbial Remobilisation on Riverbed Sediment Disturbance in Experimental Flumes and a Human-Impacted River: Implication for Water Resource Management and Public Health in Developing Sub-Saharan African Countries

    Science.gov (United States)

    Abia, Akebe Luther King; James, Chris; Ubomba-Jaswa, Eunice; Benteke Momba, Maggy Ndombo

    2017-01-01

    Resuspension of sediment-borne microorganisms (including pathogens) into the water column could increase the health risk for those using river water for different purposes. In the present work, we (1) investigated the effect of sediment disturbance on microbial resuspension from riverbed sediments in laboratory flow-chambers and in the Apies River, Gauteng, South Africa; and (2) estimated flow conditions for sediment-borne microorganism entrainment/resuspension in the river. For mechanical disturbance, the top 2 cm of the sediment in flow-chambers was manually stirred. Simulating sudden discharge into the river, water (3 L) was poured within 30 s into the chambers at a 45° angle to the chamber width. In the field, sediment was disturbed by raking the riverbed and by cows crossing in the river. Water samples before and after sediment disturbance were analysed for Escherichia coli. Sediment disturbance caused an increase in water E. coli counts by up to 7.9–35.8 times original values. Using Shields criterion, river-flow of 0.15–0.69 m3/s could cause bed particle entrainment; while ~1.57–7.23 m3/s would cause resuspension. Thus, sediment disturbance in the Apies River would resuspend E. coli (and pathogens), with possible negative health implications for communities using such water. Therefore, monitoring surface water bodies should include microbial sediment quality. PMID:28295001

  6. Microbial Remobilisation on Riverbed Sediment Disturbance in Experimental Flumes and a Human-Impacted River: Implication for Water Resource Management and Public Health in Developing Sub-Saharan African Countries

    Directory of Open Access Journals (Sweden)

    Akebe Luther King Abia

    2017-03-01

    Full Text Available Resuspension of sediment-borne microorganisms (including pathogens into the water column could increase the health risk for those using river water for different purposes. In the present work, we (1 investigated the effect of sediment disturbance on microbial resuspension from riverbed sediments in laboratory flow-chambers and in the Apies River, Gauteng, South Africa; and (2 estimated flow conditions for sediment-borne microorganism entrainment/resuspension in the river. For mechanical disturbance, the top 2 cm of the sediment in flow-chambers was manually stirred. Simulating sudden discharge into the river, water (3 L was poured within 30 s into the chambers at a 45° angle to the chamber width. In the field, sediment was disturbed by raking the riverbed and by cows crossing in the river. Water samples before and after sediment disturbance were analysed for Escherichia coli. Sediment disturbance caused an increase in water E. coli counts by up to 7.9–35.8 times original values. Using Shields criterion, river-flow of 0.15–0.69 m3/s could cause bed particle entrainment; while ~1.57–7.23 m3/s would cause resuspension. Thus, sediment disturbance in the Apies River would resuspend E. coli (and pathogens, with possible negative health implications for communities using such water. Therefore, monitoring surface water bodies should include microbial sediment quality.

  7. Final report on the REAL-84 exercise

    International Nuclear Information System (INIS)

    Zijp, W.L.; Nolthenius, H.J.

    1988-11-01

    The main aim of the REAL-84 exercise, organized by the International Atomic Energy Agency in Vienna, was to improve the assessment of accuracies in radiation damage predictions by various laboratories using good quality input data and proper calculation methods. The emphasis was concentrated on radiation damage characterization to reactor pressure vessels and related neutron technology. The long term aim of this exercise was to strive towards the establishment of standardized metrology procedures and recommended nuclear data for use in spectrum adjustment and damage parameter calculations. In this calculation exercise dealing with seven different neutron spectra the best available input data were used. Also some utility programs were included to facilitate the preparation of input data for the adjustment codes. This final report presents a discussion on the 44 sets of adjustment results received from 12 laboratories. The comparison of the results of the various spectra showed in most cases a relatively large and unexpected interlaboratory spread. Attention is given to this phenomenon. Also the quality of the input data set and a characterization of covariance matrices is summarized

  8. Environmental friendly high efficient light source plasma lamp - Final report

    Energy Technology Data Exchange (ETDEWEB)

    Courret, G.; Calame, L. [Haute Ecole d' ingenierie et de gestion du canton de Vaud, Institut de micro et nano techniques, Yverdon-les-Bains (Switzerland); Meyer, A. [Solaronix SA, Aubonne (Switzerland)

    2007-07-01

    This illustrated final report for the Swiss Federal Office of Energy (SFOE) takes a look at work done on the development of a sulphur-based plasma lamp. In 2007, the capability of a new modulator has been explored. The most important results are discussed. With the production of a 1.2 cm{sup 3} bulb, the way towards the production of a 100 W lamp has been opened. The authors comment that modulation by impulses increases the luminous efficiency in comparison to modulation using a continuous sinusoidal wave. The report deals with the history of the project, the development of the new modulator, the use of rotational effects and the optimisation of the amount of active substances - tellurium and selenium - in the bulb. The electromagnetic coupling system used is described and discussed.

  9. Early-Onset Psychoses: Comparison of Clinical Features and Adult Outcome in 3 Diagnostic Groups

    Science.gov (United States)

    Ledda, Maria Giuseppina; Fratta, Anna Lisa; Pintor, Manuela; Zuddas, Alessandro; Cianchetti, Carlo

    2009-01-01

    A comparison of clinical features and adult outcome in adolescents with three types of psychotic disorders: schizophrenic (SPh), schizoaffective (SA) and bipolar with psychotic features (BPP). Subjects (n = 41) were finally diagnosed (DSM-IV criteria) with SPh (n = 17), SA (n = 11) or BPP (n = 13). Clinical evaluation took place at onset and at a…

  10. Analysis of stock market anomalies: US cross-sectoral comparison

    OpenAIRE

    Jílek, Lukáš

    2012-01-01

    The purpose of this thesis is to analyze anomalies in the US stock market. Special attention is put on Day of the week effect, January effect, and Part of the month effect. We focus on comparison of companies with low and high capitalization. We perform an analysis across 6 major industrial sectors. Then, we discuss the findings with results of past projects and finally, we try to find a speculative investment strategy. We found out that neither Day of the week effect nor January effect do no...

  11. Clinical reasoning skills in final-year dental students: A qualitative cross-curricula comparison.

    Science.gov (United States)

    Nafea, E T; Dennick, R

    2018-05-01

    The aim of this research was to explore the perceptions of undergraduate dental students regarding clinical reasoning skills and also discover the influences of different curriculum designs on the acquisition of these skills by students. Eighteen final-year students from three different dental schools with varied curricula and cultures participated in the current research. The research used qualitative methodology. The study took place in 2013-2014. Interviews captured the participants' own understanding of clinical reasoning and its acquisition plus they "talked through" a clinical problem using a "think-aloud" technique. Thematic analysis was used to analyse the transcripts of the recorded interviews. Results obtained were related to curriculum structure. Unfamiliarity with the term clinical reasoning was common in students. Students from different schools used different strategies to reason when discussing clinical vignettes. Clinical reasoning process was dominated by pattern recognition. Students' behaviours seemed to be influenced by cultural factors. This research contributes to a greater understanding of how students learn, understand and apply dental clinical reasoning which will improve educational practices in the future. © 2017 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  12. Comparison principle for impulsive functional differential equations with infinite delays and applications

    Science.gov (United States)

    Li, Xiaodi; Shen, Jianhua; Akca, Haydar; Rakkiyappan, R.

    2018-04-01

    We introduce the Razumikhin technique to comparison principle and establish some comparison results for impulsive functional differential equations (IFDEs) with infinite delays, where the infinite delays may be infinite time-varying delays or infinite distributed delays. The idea is, under the help of Razumikhin technique, to reduce the study of IFDEs with infinite delays to the study of scalar impulsive differential equations (IDEs) in which the solutions are easy to deal with. Based on the comparison principle, we study the qualitative properties of IFDEs with infinite delays , which include stability, asymptotic stability, exponential stability, practical stability, boundedness, etc. It should be mentioned that the developed results in this paper can be applied to IFDEs with not only infinite delays but also persistent impulsive perturbations. Moreover, even for the special cases of non-impulsive effects or/and finite delays, the criteria prove to be simpler and less conservative than some existing results. Finally, two examples are given to illustrate the effectiveness and advantages of the proposed results.

  13. Analysis of higher order optical aberrations in the SLC final focus using Lie Algebra techniques

    International Nuclear Information System (INIS)

    Walker, N.J.; Irwin, J.; Woodley, M.

    1993-04-01

    The SLC final focus system is designed to have an overall demagnification of 30:1, with a β at the interaction point (β*) of 5 mm, and an energy band pass of ∼0.4%. Strong sextupole pairs are used to cancel the large chromaticity which accrues primarily from the final triplet. Third-order aberrations limit the performance of the system, the dominating terms being U 1266 and U 3466 terms (in the notation of K. Brown). Using Lie Algebra techniques, it is possible to analytically calculate the soave of these terms in addition to understanding their origin. Analytical calculations (using Lie Algebra packages developed in the Mathematica language) are presented of the bandwidth and minimum spot size as a function of divergence at the interaction point (IP). Comparisons of the analytical results from the Lie Algebra maps and results from particle tracking (TURTLE) are also presented

  14. Risk perspective on final disposal of nuclear waste. Individuals, society and communication

    International Nuclear Information System (INIS)

    Lindblad, Inga-Britt

    2007-01-01

    This report tries to evaluate the importance of the risk perspective in connection with final storage of nuclear waste. The concept 'risk' has different importance for experts and general public, within different research directions and among stakeholders in the nuclear waste issue. The report has been published in order to give an interdisciplinary scientific perspective on the risk concept. The authors have their background in different disciplines: radiation physics, psychology, media- and communications-science. The report treats four different themes: The first theme concerns perspectives on the risk concept and describes various principles for how risks can be handled in the society. The next theme is about comparing various risks. This section shows that risk comparisons can to be done within the framework of a scientific attitude and during certain given conditions. The third theme elucidates results from research about subjective risk, and shows that a large number of factors influence how risks are considered by individuals, and can influence his risk behavior and also how the individual means that the society will make decisions in risk-related questions. The fourth and last theme is about risk communication. Since the risk concept contains many different aspects it is clear that risk should not only be informed about, but also communicated. If a purely mathematical definition of risk was the only valid form, such information, from experts to the citizens, would possibly be sufficient. But since there are other relevant factors to take into consideration (t.ex the individual's own values), a communicative process must take place, i.e. the citizens should have influence on how risks are compared and managed. In the final theme, the authors have chosen to reflect around the themes above, i.e. different perspectives on the risk concept, risk comparisons, subjective risk view and risk communication are discussed

  15. Spent fuel management strategies in eight countries and applicability to Sweden. Final report

    International Nuclear Information System (INIS)

    1986-01-01

    International Energy Associates Limited (IEAL) undertook this study on behalf of Sweden's National Board for Spent Nuclear Fuel (SKN) from June to October 1986. The purpose of the project was to compare the programs and regulations for the management of spent fuel from nuclear power plants and disposal of high-level radioactive waste in eight countries: Belgium, Canada, the Federal Republic of Germany, France, Japan, Switzerland, the United Kingdom and the United States. This final report includes revisions requested by SKN upon review of the draft report dated in September 26, 1986. The study is presented in three volumes. Volume I (Section 2.0 of the report) consists of detailed country-specific reports on the policies, regulations and strategies for spent fuel and high-level waste management in each of the eight countries. The information contained in these country-specific reports was used as the basis for comparing the options in each country in terms of cost, environmental impact, and public acceptability, and for comparing the policies and regulatory requirements affecting these activities in each country. These comparisons are provided in Volume II (Section 3.0 of the report). Section 3.0 also includes a discussion of the applicability to Sweden of the strategies and policies in the eight countries studied. Finally, Volume III of the report (Section 4.0) presents the laws, regulations and other documents pertinent to spent fuel and high-level waste management in these countries. Descriptive summaries of the documents are provided in Section 4.0, a comparison guide to the documents themselves (the great majority of them in English) which are provided in 15 volumes of appendices

  16. Unique electron polarimeter analyzing power comparison and precision spin-based energy measurement

    International Nuclear Information System (INIS)

    Joseph Grames; Charles Sinclair; Joseph Mitchell; Eugene Chudakov; Howard Fenker; Arne Freyberger; Douglas Higinbotham; Poelker, B.; Michael Steigerwald; Michael Tiefenback; Christian Cavata; Stephanie Escoffier; Frederic Marie; Thierry Pussieux; Pascal Vernin; Samuel Danagoulian; Kahanawita Dharmawardane; Renee Fatemi; Kyungseon Joo; Markus Zeier; Viktor Gorbenko; Rakhsha Nasseripour; Brian Raue; Riad Suleiman; Benedikt Zihlmann

    2004-01-01

    Precision measurements of the relative analyzing powers of five electron beam polarimeters, based on Compton, Moller, and Mott scattering, have been performed using the CEBAF accelerator at the Thomas Jefferson National Accelerator Facility (Jefferson Laboratory). A Wien filter in the 100 keV beamline of the injector was used to vary the electron spin orientation exiting the injector. High statistical precision measurements of the scattering asymmetry as a function of the spin orientation were made with each polarimeter. Since each polarimeter receives beam with the same magnitude of polarization, these asymmetry measurements permit a high statistical precision comparison of the relative analyzing powers of the five polarimeters. This is the first time a precise comparison of the analyzing powers of Compton, Moller, and Mott scattering polarimeters has been made. Statistically significant disagreements among the values of the beam polarization calculated from the asymmetry measurements made with each polarimeter reveal either errors in the values of the analyzing power, or failure to correctly include all systematic effects. The measurements reported here represent a first step toward understanding the systematic effects of these electron polarimeters. Such studies are necessary to realize high absolute accuracy (ca. 1%) electron polarization measurements, as required for some parity violation measurements planned at Jefferson Laboratory. Finally, a comparison of the value of the spin orientation exiting the injector that provides maximum longitudinal polarization in each experimental hall leads to an independent and very precise (better than 10-4) absolute measurement of the final electron beam energy

  17. Final state effects in neutron Compton scattering measurements

    International Nuclear Information System (INIS)

    Fielding, A.L.

    1997-10-01

    The single atom momentum distributions of condensed matter systems can be derived using the technique of neutron Compton scattering (NCS). The electron Volt spectrometer (eVS) which is situated at the world's most intense pulsed neutron spallation source, ISIS, has been configured to perform NCS measurements. Interpretation of NCS data requires the use of the impulse approximation, however even at the high energy and momentum transfers obtainable on the eVS deviations from the impulse approximation occur. These deviations are generally known as final state effects (FSE) which manifest themselves as an asymmetry in the measured momentum distribution. The aim of the work reported in this thesis is to demonstrate how final state effects can be accounted for in a simple way using the expansion method described by Sears. An advantage of the Sears method is that the first asymmetric term in the expansion is proportional to the mean Laplacian of the potential, 2 V>, thus giving access to further information on the single atom potential. The Sears expansion has been incorporated into data analysis routines and applied to measured data on three systems that were chosen to represent the systems that are regularly investigated using the eVS. Measurements have been carried out on the deuteron in ZrD 2 , a light atom in a heavy lattice, beryllium, a polycrystalline solid and pyrolytic graphite, an aligned crystalline sample with an anisotropic momentum distribution. The study shows how the new analysis method gives more reliable values for the mean kinetic energy k >, which can be derived from the measured momentum distribution. A comparison of measured data with simulated data calculated within the harmonic approximation reveals how 2 V> can be a sensitive probe of anharmonicity of the interatomic potential. An anisotropy in the derived k > and 2 V> of pyrolytic graphite has been measured indicating the dependence of final state effects on bonding strength. The derived 2 V

  18. Sanitary landfill in situ bioremediation optimization test. Final report

    International Nuclear Information System (INIS)

    1996-01-01

    This work was performed as part of a corrective action plan for the Savannah River Site Sanitary Landfill. This work was performed for the Westinghouse Savannah River Company Environmental Restoration Department as part of final implementation of a groundwater remediation system for the SRS Sanitary Landfill. Primary regulatory surveillance was provided by the South Carolina Department of Health and Environmental Control and the US Environmental Protection Agency (Region IV). The characterization, monitoring and remediation systems in the program generally consisted of a combination of innovative and baseline methods to allow comparison and evaluation. The results of these studies will be used to provide input for the full-scale groundwater remediation system for the SRS Sanitary Landfill. This report summarizes the performance of the Sanitary Landfill In Situ Optimization Test data, an evaluation of applicability, conclusions, recommendations, and related information for implementation of this remediation technology at the SRS Sanitary Landfill

  19. The Comparison Study of Six University Archives

    Directory of Open Access Journals (Sweden)

    Chun-Fen Liu

    2004-03-01

    Full Text Available The university archives is not only the extension of a building, but also includes the archival records, archivists and equipments. The university archives is the historical memory of a university, which could let people to predict the future by reviewing the past. The university archives has abundant collections, both teachers and students can review history of this university. This paper mainly compares six university archives of Taiwan, and the interviewing method is used in this research. After comparison of the six university archives, we have found the six university archives have different organizational structures, budgets, and functions. Finally the authors propose some suggestions.[Article content in Chinese

  20. Methodology for calculating radiation doses from radioactivity released to the environment

    International Nuclear Information System (INIS)

    Killough, G.G.; McKay, L.R.

    1976-03-01

    This document represents a compilation of the principal environmental transport and dosimetry models developed, adapted, and implemented by the Radiological Analyses and Applications Group of the Environmental Sciences Division of the Oak Ridge National Laboratory. The transport of released radioactivity through the natural environment is discussed in four sections: atmospheric dispersion, resuspension of material by wind action, terrestrial transport, and movement of material in underground water seepage. The discussion of dose to man and biota is divided into internal and external exposure sections. And finally, a developmental model (CONDOS) which estimates the dose to a population resulting from the manufacture, storage, distribution, use, and disposal of consumer products which contain radioactivity is described. Numerous tables are included

  1. Comparison of Simulations and Offshore Measurement Data of a Combined Floating Wind and Wave Energy Demonstration Platform

    DEFF Research Database (Denmark)

    Yde, Anders; Larsen, Torben J.; Hansen, Anders Melchior

    2015-01-01

    In this paper, results from comparisons of simulations and measured offshore data from a floating combined wind and wave energy conversion system are presented. The numerical model of the platform is based on the aeroelastic code, HAWC2, developed by DTU Wind Energy, which is coupled with a special...... external system that reads the output generated directly by the wave analysis software WAMIT. The main focus of the comparison is on the statistical trends of the platform motion, mooring loads, and turbine loads in measurements and simulations during different operational conditions. Finally, challenges...

  2. Comparison of radiation doses obtained for radiation monitoring of controlled areas with radiation doses obtained for personnel dosimetry in radiodiagnosis centers

    International Nuclear Information System (INIS)

    Lescano, Roberto; Caspani, Carlos; Universidad Nacional del Litoral, Santa Fe

    2001-01-01

    In this paper we propose to search an indicator that shows, at an objective way, the quality of the radioprotection actions. The method is about to determine doses, measured in the work area, connecting them with the workload, and finally get the dose for the center. Them we make a comparison with the personal film dosimetry data. We discuss the final results, evaluating the radioprotection conditions in daily work. (author)

  3. A Comparison of Methods for Estimating the Determinant of High-Dimensional Covariance Matrix

    KAUST Repository

    Hu, Zongliang; Dong, Kai; Dai, Wenlin; Tong, Tiejun

    2017-01-01

    The determinant of the covariance matrix for high-dimensional data plays an important role in statistical inference and decision. It has many real applications including statistical tests and information theory. Due to the statistical and computational challenges with high dimensionality, little work has been proposed in the literature for estimating the determinant of high-dimensional covariance matrix. In this paper, we estimate the determinant of the covariance matrix using some recent proposals for estimating high-dimensional covariance matrix. Specifically, we consider a total of eight covariance matrix estimation methods for comparison. Through extensive simulation studies, we explore and summarize some interesting comparison results among all compared methods. We also provide practical guidelines based on the sample size, the dimension, and the correlation of the data set for estimating the determinant of high-dimensional covariance matrix. Finally, from a perspective of the loss function, the comparison study in this paper may also serve as a proxy to assess the performance of the covariance matrix estimation.

  4. A Comparison of Methods for Estimating the Determinant of High-Dimensional Covariance Matrix

    KAUST Repository

    Hu, Zongliang

    2017-09-27

    The determinant of the covariance matrix for high-dimensional data plays an important role in statistical inference and decision. It has many real applications including statistical tests and information theory. Due to the statistical and computational challenges with high dimensionality, little work has been proposed in the literature for estimating the determinant of high-dimensional covariance matrix. In this paper, we estimate the determinant of the covariance matrix using some recent proposals for estimating high-dimensional covariance matrix. Specifically, we consider a total of eight covariance matrix estimation methods for comparison. Through extensive simulation studies, we explore and summarize some interesting comparison results among all compared methods. We also provide practical guidelines based on the sample size, the dimension, and the correlation of the data set for estimating the determinant of high-dimensional covariance matrix. Finally, from a perspective of the loss function, the comparison study in this paper may also serve as a proxy to assess the performance of the covariance matrix estimation.

  5. A Comparison of Methods for Estimating the Determinant of High-Dimensional Covariance Matrix.

    Science.gov (United States)

    Hu, Zongliang; Dong, Kai; Dai, Wenlin; Tong, Tiejun

    2017-09-21

    The determinant of the covariance matrix for high-dimensional data plays an important role in statistical inference and decision. It has many real applications including statistical tests and information theory. Due to the statistical and computational challenges with high dimensionality, little work has been proposed in the literature for estimating the determinant of high-dimensional covariance matrix. In this paper, we estimate the determinant of the covariance matrix using some recent proposals for estimating high-dimensional covariance matrix. Specifically, we consider a total of eight covariance matrix estimation methods for comparison. Through extensive simulation studies, we explore and summarize some interesting comparison results among all compared methods. We also provide practical guidelines based on the sample size, the dimension, and the correlation of the data set for estimating the determinant of high-dimensional covariance matrix. Finally, from a perspective of the loss function, the comparison study in this paper may also serve as a proxy to assess the performance of the covariance matrix estimation.

  6. Mission related to regulation and development of the photovoltaic sector in France. Final report; Mission relative a la regulation et au developpement de la filiere photovoltaique en France. Rapport final

    Energy Technology Data Exchange (ETDEWEB)

    Charpin, J.M; Sine, A.; Helleisen, Ph.; Tlili, C. [Inspection Generale des Finances - IGF, 75 - Paris (France); Trink, C.; Stoffaes, Ch. [Conseil General de l' Industrie de l' Energie et des Technologies - CGIET, 75 - Paris (France)

    2010-07-01

    This report first gives an overview of the development of the photovoltaic stock in France (high potential with a middle term development constrained by high costs, consequences of a very strong increase of demands at the end of 2009, perspective of development at a rather high rate). Then, it outlines and discusses the financial consequences of such a high rate development, and the inadequacy between industrial objectives and development rate. It presents a development plan for this sector, stresses the need to implement new purchase obligation measures before the summer 2010, and to define a global action plan to be implemented at the beginning of 2011 for the development of photovoltaic electricity. Elements of international comparison are finally proposed

  7. TARGET 2 and Settlement Finality

    Directory of Open Access Journals (Sweden)

    Ivan MANGATCHEV

    2011-03-01

    Full Text Available This article examines how TARGET 2 as system implements the idea of settlement finality regulated by Directive 98/26 EC of the European parliament and of the Council of 19 May 1998 on settlement finality in payment and securities settlement systems (Settlement Finality Directive and Directive 2009/44/EC of the European parliament and of the Council of 6 May 2009 amending Directive 98/26/EC on settlement finality in payment and securities settlement systems and Directive 2002/47/EC on financial collateral arrangements as regards linked systems and credit claims (Directive 2009/44/EC. As the title of the arti and finality of the settlement in this system.

  8. Regulatory analysis for final rule on nuclear power plant license renewal

    International Nuclear Information System (INIS)

    1991-12-01

    This regulatory analysis provides the supporting information for the final rule (10 CFR Part 54) that defines the Nuclear Regulatory Commission's requirements for renewing the operating licenses of commercial nuclear power plants. A set of four specific alternatives for the safety review of license renewal applications is defined and evaluated. These are: Alternative A-current licensing basis; Alternative B-extension of Alternative A to require assessment and managing of aging; Alternative C -- extension of Alternative B to require assessment of design differences against selected new-plant standards using probabilistic risk assessment; and Alternative D -- extension of Alternative B to require compliance with all new-plant standards. A quantitative comparison of the four alternatives in terms of impact-to-value ratio is presented, and Alternative B is the most cost-beneficial safety review alternative

  9. IEA Wind Task 23 Offshore Wind Technology and Deployment. Subtask 1 Experience with Critical Deployment Issues. Final Technical Report

    OpenAIRE

    Lemming, Jørgen Kjærgaard

    2010-01-01

    The final report for IEA Wind Task 23, Offshore Wind Energy Technology and Deployment, is made up of two separate reports: Subtask 1: Experience with Critical Deployment Issues and Subtask 2: Offshore Code Comparison Collaborative (OC3). The Subtask 1 report included here provides background information and objectives of Task 23. It specifically discusses ecological issues and regulation, electrical system integration and offshore wind, external conditions, and key conclusions for Subtask 1. ...

  10. The theory of the interaction of atmospheric aerosol with underlying surface

    International Nuclear Information System (INIS)

    Buikov, M.V.

    1993-01-01

    The interaction of wind with underlying surfaces through resuspension makes a great contribution to the total amount of atmospheric aerosols. The dry deposition process results in cleaning of the atmosphere and contamination of near-surface air layers of soil and vegetation. This paper examines the theory leading to an exact solution of the problem of turbulent transportation of pollution taking into account resuspension and dry-deposition. This may be useful for the interpretation of observational data and for the improvement of calculation methods to describe aerosol exchange at surfaces in air. (author)

  11. Final report on plan of action concerning Fukushima

    International Nuclear Information System (INIS)

    2016-12-01

    This brochure published by the Swiss National Safety Inspectorate ENSI discusses various protection measures for nuclear installations in Switzerland. Protection against natural incidents such as earthquakes, flooding and extreme weather conditions is first discussed, followed by a discussion on the protection needed against the loss of fundamental safety functions. These include loss of mains power and loss of heat sink capacity for cooling. Severe Accident Management is also discussed: the setting-up of emergency equipment stores, securing containment integrity, strategies and the organisation of long-term emergency response. Contamination propagation in rivers and streams is looked at, as are the effects of dangerous non-nuclear substances. Emergency response on a national scale is examined. Requirements placed on measurement and prognosis systems, reference scenarios and demands placed on communication systems are noted. Safety culture is looked at in Swiss nuclear installations. ENSI’s supervision culture is also commented on, as are international activities in this area. Finally, current research and measures are examined and a comparison is made with the international investigations made as a result of the Fukushima Incident

  12. Calculation to experiment comparison of SPND signals in various nuclear reactor environments

    Energy Technology Data Exchange (ETDEWEB)

    Barbot, Loic; Radulovic, Vladimir; Fourmentel, Damien [CEA, DEN, DER, Instrumentation, Sensors and Dosimetry Laboratory, Cadarache, F-13108 St-Paul-Lez-Durance, (France); Snoj, Luka [Jozef Stefan Institute, Jamova cesta 39, SI-1000 Ljubljana, (Slovenia); Tarchalski, Mikolaj [National Centre for Nuclear Research, ulica Andrzeja Soltana 7, 05-400 Otwock (Swierk), (Poland); Dewynter-Marty, Veronique [CEA, DEN, DANS, DRSN, SIREN, LESCI, Saclay, F-91191 Gif sur Yvette, (France); Malouch, Fadhel [CEA, DEN, DANS, DM2S, SERMA, Saclay, F-91191 Gif sur Yvette, (France)

    2015-07-01

    In the perspective of irradiation experiments in the future Jules Horowitz Reactor (JHR), the Instrumentation Sensors and Dosimetry Laboratory of CEA Cadarache (France) is developing a numerical tool for SPND design, simulation and operation. In the frame of the SPND numerical tool qualification, dedicated experiments have been performed both in the Slovenian TRIGA Mark II reactor (JSI) and very recently in the French CEA Saclay OSIRIS reactor, as well as a test of two detectors in the core of the Polish MARIA reactor (NCBJ). A full description of experimental set-ups and neutron-gamma calculations schemes are provided in the first part of the paper. Calculation to experiment comparison of the various SPNDs in the different reactors is thoroughly described and discussed in the second part. Presented comparisons show promising final results. (authors)

  13. Comparison report of the OECD/CSNI international standard problem 21 (Piper-one experiment PO-SB-7). Volume 1 comparison report. Volume 2 evaluation of code accuracy in the prediction of ISP 21

    International Nuclear Information System (INIS)

    1989-11-01

    The present report deals with the comparison of 6 blind predictions, submitted by 5 participants, and the experimental results measured during the test PO-SB-7 performed in PIPER-ONE facility. The PIPER-ONE apparatus is an experimental simulator of a General Electric BWR. The test PO-SB-7 simulates a SB-LOCA originated by a break in one recirculation line of the reference BWR-6 plant, without intervention of high pressure ECCS. The overall activity constitutes the CSNI ISP-21. The main parts of the report are: a) outline of the test facility and of the PO-SB-7 experiment; b) overview of input models used by participants; c) evaluation of participant predictions on the basis of one-by-one comparison with selected experimental trends; d) evaluation of present code capabilities and accuracy, on the basis of the overall comparison between measured data and participants double blind predictions. Finally, a judgement is given in relation to the overall value of the activity

  14. Standardization of Tc-99 by two methods and participation at the CCRI(II)-K2. Tc-99 comparison.

    Science.gov (United States)

    Sahagia, M; Antohe, A; Ioan, R; Luca, A; Ivan, C

    2014-05-01

    The work accomplished within the participation at the 2012 key comparison of Tc-99 is presented. The solution was standardized for the first time in IFIN-HH by two methods: LSC-TDCR and 4π(PC)β-γ efficiency tracer. The methods are described and the results are compared. For the LSC-TDCR method, the program TDCR07c, written and provided by P. Cassette, was used for processing the measurement data. The results are 2.1% higher than when applying the TDCR06b program; the higher value, calculated with the software TDCR07c, was used for reporting the final result in the comparison. The tracer used for the 4π(PC)β-γ efficiency tracer method was a standard (60)Co solution. The sources were prepared from the mixture (60)Co+(99)Tc solution and a general extrapolation curve, type: N(βTc-99)/(M)(Tc-99)=f [1-ε(Co-60)], was drawn. This value was not used for the final result of the comparison. The difference between the values of activity concentration obtained by the two methods was within the limit of the combined standard uncertainty of the difference of these two results. © 2013 Published by Elsevier Ltd.

  15. Impact of the zebra mussel Dreissena polymorpha invasion on the budget of suspended material in a shallow lagoon ecosystem

    Science.gov (United States)

    Daunys, Darius; Zemlys, Petras; Olenin, Sergej; Zaiko, Anastasija; Ferrarin, Christian

    2006-05-01

    The role of the zebra mussel Dreissena polymorpha in redistribution of total particulate material (TPM) between the water column and bottom sediment was estimated using the TPM budget for a mussel bed in the Curonian lagoon, the Baltic Sea. Seasonal clearance rates were derived from the TPM budget assuming two resuspension scenarios: no resuspension and full resuspension of biodeposits. Estimated clearance rates for both scenarios were compared with the rates calculated from the population clearance rate model. Seasonal clearance rates estimated using the population model (1.1 and 11.8 l g-1 SFDW day-1) fitted well into the interval of seasonal clearance rates calculated from TPM budgets assuming no resuspension of biodeposits (3.2 and 21.4 l g SFDW-1 day-1). In the scenario with biodeposits resuspension clearance rates were much higher (57.4 and 148.9 g SFDW-1 day-1). The ratio of clearance to residence time was highly dependent on the fate of biodeposits. Therefore its use in interpretation of the species impact on TPM was limited. An alternative measure based on the ratio of the amount of TPM biodeposited to TPM transported into the bed was used. It was found that zebra mussels are able to deposit between 10 and 30% of the incoming TPM, and the amount of biodeposited material was correlated with water residence time. Results indicate that the impact of zebra mussels on TPM in the lagoon is small relative to the high transport rates of TPM over the bed. However, annual biosedimentation rate (~590 g m-2) in the mussel bed was higher than physical deposition rate (~380 g m-2) in accumulation areas devoid of large suspension feeders. We suggest that a local impact due to enhanced availability of organic material to other trophic groups of associated benthic organisms may be more significant than effects on TPM pathways at an ecosystem scale.

  16. Satellite Assessment of Bio-Optical Properties of Northern Gulf of Mexico Coastal Waters Following Hurricanes Katrina and Rita.

    Science.gov (United States)

    Lohrenz, Steven E; Cai, Wei-Jun; Chen, Xiaogang; Tuel, Merritt

    2008-07-10

    The impacts of major tropical storms events on coastal waters include sediment resuspension, intense water column mixing, and increased delivery of terrestrial materials into coastal waters. We examined satellite imagery acquired by the Moderate Resolution Imaging Spectroradiometer (MODIS) ocean color sensor aboard the Aqua spacecraft following two major hurricane events: Hurricane Katrina, which made landfall on 29 August 2005, and Hurricane Rita, which made landfall on 24 September. MODIS Aqua true color imagery revealed high turbidity levels in shelf waters immediately following the storms indicative of intense resuspension. However, imagery following the landfall of Katrina showed relatively rapid return of shelf water mass properties to pre-storm conditions. Indeed, MODIS Aqua-derived estimates of diffuse attenuation at 490 nm (K_490) and chlorophyll (chlor_a) from mid-August prior to the landfall of Hurricane Katrina were comparable to those observed in mid-September following the storm. Regions of elevated K_490 and chlor_a were evident in offshore waters and appeared to be associated with cyclonic circulation (cold-core eddies) identified on the basis of sea surface height anomaly (SSHA). Imagery acquired shortly after Hurricane Rita made landfall showed increased water column turbidity extending over a large area of the shelf off Louisiana and Texas, consistent with intense resuspension and sediment disturbance. An interannual comparison of satellite-derived estimates of K_490 for late September and early October revealed relatively lower levels in 2005, compared to the mean for the prior three years, in the vicinity of the Mississippi River birdfoot delta. In contrast, levels above the previous three year mean were observed off Texas and Louisiana 7-10 d after the passage of Rita. The lower values of K_490 near the delta could be attributed to relatively low river discharge during the preceding months of the 2005 season. The elevated levels off Texas and

  17. 75 FR 62133 - Notice of Availability of Final Environmental Assessment (FINAL EA) and a Finding of No...

    Science.gov (United States)

    2010-10-07

    ... Availability of Final Environmental Assessment (FINAL EA) and a Finding of No Significant Impact (FONSI) for... of No Significant Impact (FONSI) for Land Purchase, Access Road Construction and Access Tunnel... Impact (FONSI) based on the Final Environmental Assessment (FINAL EA) for Land Purchase, Access Road...

  18. 14 CFR 1214.1105 - Final ranking.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 5 2010-01-01 2010-01-01 false Final ranking. 1214.1105 Section 1214.1105... Recruitment and Selection Program § 1214.1105 Final ranking. Final rankings will be based on a combination of... preference will be included in this final ranking in accordance with applicable regulations. ...

  19. Comparison of Static Picture and Video Prompting on the Performance of Cooking-Related Tasks by Students with Autism

    Science.gov (United States)

    Mechling, Linda C.; Gustafson, Melissa R.

    2009-01-01

    This study compared the effectiveness of static photographs and video prompts on the independent task performance of six young men with a diagnosis of autism. An adapted alternating-treatment design with baseline, comparison, withdrawal, and final treatment conditions was used to measure the percentage of cooking-related tasks completed…

  20. 78 FR 43912 - Final Candidate Conservation Agreement with Assurances, Final Environmental Assessment, and...

    Science.gov (United States)

    2013-07-22

    ...-FF02ENEH00] Final Candidate Conservation Agreement with Assurances, Final Environmental Assessment, and Finding of No Significant Impact; Rio Grande Cutthroat Trout, New Mexico and Colorado AGENCY: Fish and... environmental assessment (EA) and the draft Finding of No Significant Impact (FONSI) under the National...

  1. Finite Element Analysis and Test Results Comparison for the Hybrid Wing Body Center Section Test Article

    Science.gov (United States)

    Przekop, Adam; Jegley, Dawn C.; Rouse, Marshall; Lovejoy, Andrew E.

    2016-01-01

    This report documents the comparison of test measurements and predictive finite element analysis results for a hybrid wing body center section test article. The testing and analysis efforts were part of the Airframe Technology subproject within the NASA Environmentally Responsible Aviation project. Test results include full field displacement measurements obtained from digital image correlation systems and discrete strain measurements obtained using both unidirectional and rosette resistive gauges. Most significant results are presented for the critical five load cases exercised during the test. Final test to failure after inflicting severe damage to the test article is also documented. Overall, good comparison between predicted and actual behavior of the test article is found.

  2. Environmental and traffic-related parameters affecting road dust composition: A multi-technique approach applied to Venice area (Italy)

    Science.gov (United States)

    Valotto, Gabrio; Rampazzo, Giancarlo; Visin, Flavia; Gonella, Francesco; Cattaruzza, Elti; Glisenti, Antonella; Formenton, Gianni; Tieppo, Paulo

    2015-12-01

    Road dust is a non-exhaust source of atmospheric particulate by re-suspension. It is composed of particles originating from natural sources as well as other non-exhaust source such as tire, brake and asphalt wear. The discrimination between atmospheric particles directly emitted from abrasion process and those related to re-suspension is therefore an open issue, as far as the percentage contribution of non-exhaust emissions is becoming more considerable due also to the recent policy actions and the technological upgrades in the automotive field, focused on the reduction of exhaust emissions. In this paper, road dust collected along the bridge that connects Venice (Italy) to the mainland is characterized with a multi-technique approach in order to determine its composition depending on environmental as well as traffic-related conditions. Six pollutant sources of road dust particles were identified by cluster analysis: brake, railway, tire, asphalt, soil + marine, and mixed combustions. Considering the lack of information on this matrix in this area, this study is intended to provide useful information for future identification of road dust re-suspension source in atmospheric particulate.

  3. Surveillance of the North-Eastern Atlantic dumpsite for low-level radioactive waste. The Swiss oceanographic research program 'PROSPER'. Progress report

    International Nuclear Information System (INIS)

    Nyffeler, F.; Ruch, P.; Hanselmann, K.

    1984-08-01

    This report describes the results of the research undertaken within the CRESP program by the Swiss group PROSPER, for the surveillance of the current dumpsite for low-level radioactive waste in the North-Eastern Atlantic. About 100 nephelometric profiles obtained during three cruises in the vicinity of the site provide a sound basis for the description of the benthic nepheloid layer structure. Statistical analyses show that the last 1000 m of water above the bottom are influenced by resuspension processes or by lateral advection of particles detached from the surrounding relief. A mapping performed over a large area (200 x 200 km) confirms the accumulation of particles in topographic lows. Geochemical analysis of suspended matter and surficial sediment has been carried out in order to compare their elemental composition, and to determine the classes of particles which are more likely to be resuspended. The discrepancy between BNL and local sediment composition suggests that advective transport or resuspension of older bottom sediment, exposed following slumping from the hill slopes, could act in addition to the local resuspension of recent sediment. (author)

  4. Main areas of work of the German Radiation Protection Office (BfS). Final disposal of radioactive wastes

    International Nuclear Information System (INIS)

    Kleemann, U.

    2006-01-01

    The Federal Ministry for Environment, Nature Conservation and Reactor Safety (BMU) formulated twelve questions which are in principle relevant to all host rock formations and require clarification in any case. The task of the BfS was to compile a comparison of different host rock formations on the basis of the answers given to these twelve questions for the individual projects. The main focus was on whether these safety-related questions merit different answers for different host rock formations and whether this has an impact on the requirements to be placed on final disposal concepts

  5. Dimensional comparison theory.

    Science.gov (United States)

    Möller, Jens; Marsh, Herb W

    2013-07-01

    Although social comparison (Festinger, 1954) and temporal comparison (Albert, 1977) theories are well established, dimensional comparison is a largely neglected yet influential process in self-evaluation. Dimensional comparison entails a single individual comparing his or her ability in a (target) domain with his or her ability in a standard domain (e.g., "How good am I in math compared with English?"). This article reviews empirical findings from introspective, path-analytic, and experimental studies on dimensional comparisons, categorized into 3 groups according to whether they address the "why," "with what," or "with what effect" question. As the corresponding research shows, dimensional comparisons are made in everyday life situations. They impact on domain-specific self-evaluations of abilities in both domains: Dimensional comparisons reduce self-concept in the worse off domain and increase self-concept in the better off domain. The motivational basis for dimensional comparisons, their integration with recent social cognitive approaches, and the interdependence of dimensional, temporal, and social comparisons are discussed. PsycINFO Database Record (c) 2013 APA, all rights reserved.

  6. 10 CFR 51.93 - Distribution of final environmental impact statement and supplement to final environmental impact...

    Science.gov (United States)

    2010-01-01

    ... 10 Energy 2 2010-01-01 2010-01-01 false Distribution of final environmental impact statement and supplement to final environmental impact statement; news releases. 51.93 Section 51.93 Energy NUCLEAR... Environmental Impact Statements-General Requirements § 51.93 Distribution of final environmental impact...

  7. THE INITIAL-FINAL MASS RELATION AMONG WHITE DWARFS IN WIDE BINARIES

    International Nuclear Information System (INIS)

    Zhao, J. K.; Oswalt, T. D.; Willson, L. A.; Wang, Q.; Zhao, G.

    2012-01-01

    We present the initial-final mass relation derived from 10 white dwarfs in wide binaries that consist of a main-sequence star and a white dwarf. The temperature and gravity of each white dwarf were measured by fitting theoretical model atmospheres to the observed spectrum using a χ 2 fitting algorithm. The cooling time and mass were obtained using theoretical cooling tracks. The total age of each binary was estimated from the chromospheric activity of its main-sequence component to an uncertainty of about 0.17 dex in log t. The difference between the total age and white dwarf cooling time is taken as the main-sequence lifetime of each white dwarf. The initial mass of each white dwarf was then determined using stellar evolution tracks with a corresponding metallicity derived from spectra of their main-sequence companions, thus yielding the initial-final mass relation. Most of the initial masses of the white dwarf components are between 1 and 2 M ☉ . Our results suggest a correlation between the metallicity of a white dwarf's progenitor and the amount of post-main-sequence mass loss it experiences—at least among progenitors with masses in the range of 1-2 M ☉ . A comparison of our observations to theoretical models suggests that low-mass stars preferentially lose mass on the red giant branch.

  8. Comparison is key.

    Science.gov (United States)

    Stone, Mark H; Stenner, A Jackson

    2014-01-01

    Several concepts from Georg Rasch's last papers are discussed. The key one is comparison because Rasch considered the method of comparison fundamental to science. From the role of comparison stems scientific inference made operational by a properly developed frame of reference producing specific objectivity. The exact specifications Rasch outlined for making comparisons are explicated from quotes, and the role of causality derived from making comparisons is also examined. Understanding causality has implications for what can and cannot be produced via Rasch measurement. His simple examples were instructive, but the implications are far reaching upon first establishing the key role of comparison.

  9. Voxel-wise comparisons of the morphology of diffusion tensors across groups of experimental subjects

    DEFF Research Database (Denmark)

    Bansal, Ravi; Staib, Lawrence H; Plessen, Kerstin J

    2007-01-01

    method to compute their approximate covariance matrices. Our results show that the theoretically computed mean tensor (MT) eigenvectors and eigenvalues match well with their respective true values. Furthermore, a comparison of synthetically generated groups of DTs highlights the limitations of using FA...... to detect group differences. Finally, analyses of in vivo DT data using our method reveal significant between-group differences in diffusivity along fiber tracts within white matter, whereas analyses based on FA values failed to detect some of these differences....... neuropsychiatric illnesses. Comparisons of tensor morphology across groups have typically been performed on scalar measures of diffusivity, such as Fractional Anisotropy (FA) rather than directly on the complex 3D morphologies of DTs. Scalar measures, however, are related in nonlinear ways to the eigenvalues...

  10. CCQM key comparison CCQM-K75: Determination of toxic metals in algae

    Science.gov (United States)

    Shakhashiro, A.; Toervenyi, A.; Gaudino, S.; Rosamilia, S.; Belli, M.; Turk, G. C.

    2011-01-01

    in algae matrix. In addition, the NMIs demonstrated a wide range of 'core-capabilities' applicable to other measurement applications. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

  11. Final Report

    Energy Technology Data Exchange (ETDEWEB)

    DeTar, Carleton [P.I.

    2012-12-10

    This document constitutes the Final Report for award DE-FC02-06ER41446 as required by the Office of Science. It summarizes accomplishments and provides copies of scientific publications with significant contribution from this award.

  12. Main influence factors on the final energy generation cost of a nuclear power plant in comparison with other energy sources

    International Nuclear Information System (INIS)

    Souza, J.A.M. de; Glardon, C.; Schmidt, R.M.

    1981-01-01

    The main factors in the construction and in the operation of nuclear power plants that affect the final energy generation cost are presented. The structure of the energy generation cost, of the nuclear fuel cost and the total investment are studied. (E.G.) [pt

  13. KEY COMPARISON: CCQM-K27-Subsequent: Key Comparison (subsequent) for the determination of ethanol in aqueous matrix

    Science.gov (United States)

    Schantz, Michele M.; Duewer, David L.; Parris, Reenie M.; May, Willie E.; Archer, Marcellé; Mussell, Chris; Carter, David; Konopelko, Leonid A.; Kustikov, Yury A.; Krylov, Anatoli I.; Fatina, Olga V.

    2005-01-01

    ethanol in water were used in the subsequent study (nominal concentrations of 0.2 mg/g, 1 mg/g, 3 mg/g, and 60 mg/g). The three participants in the CCQM-K27-Subsequent Key Comparison demonstrated their ability to measure ethanol in aqueous matrix in the concentration range of 0.2 mg/g to 60 mg/g. Main text. To reach the main text of this paper, click on Final Report. The final report has been peer-reviewed and approved for publication by the CCQM, according to the provisions of the Mutual Recognition Arrangement (MRA).

  14. Mission related to regulation and development of the photovoltaic sector in France. Final report

    International Nuclear Information System (INIS)

    Charpin, J.M; Sine, A.; Helleisen, Ph.; Tlili, C.; Trink, C.; Stoffaes, Ch.

    2010-01-01

    This report first gives an overview of the development of the photovoltaic stock in France (high potential with a middle term development constrained by high costs, consequences of a very strong increase of demands at the end of 2009, perspective of development at a rather high rate). Then, it outlines and discusses the financial consequences of such a high rate development, and the inadequacy between industrial objectives and development rate. It presents a development plan for this sector, stresses the need to implement new purchase obligation measures before the summer 2010, and to define a global action plan to be implemented at the beginning of 2011 for the development of photovoltaic electricity. Elements of international comparison are finally proposed

  15. Relationship between push phase and final race time in skeleton performance.

    Science.gov (United States)

    Zanoletti, Costanza; La Torre, Antonio; Merati, Giampiero; Rampinini, Ermanno; Impellizzeri, Franco M

    2006-08-01

    The aim of this study was to examine the relationship between push-time and final race time in skeleton participants during a series of major international competitions to determine the importance of the push phase in skeleton performance. Correlations were computed from the first and second heat split data measured during 24 men and 24 women skeleton competitions. Body mass, height, age, and years of experience of the first 30 men and women athletes of the skeleton, bobsleigh and luge 2003-2004 World Cup ranking were used for the comparison between sliding sports. Moderate but significant correlations (p push-time and final race time in men (r(mean) = 0.48) and women (r(mean) = 0.63). No correlations were found between changes in the individual push-time between the first and second heat with the corresponding changes in final race time. The bobsleigh sliders are heavier than the athletes of the other sliding disciplines. Luge athletes have more experience and are younger than bobsleigh and skeleton sliders. The results of this study suggest that a fast push phase is a prerequisite to success in competition and confirms that the selection of skeleton athletes based on the ability to accelerate to a maximum speed quickly could be valid. However, a good or improved push-time does not ensure a placement in the top finishing positions. On the basis of these results, we suggest that strength and power training is necessary to maintain a short push-time but additional physical training aimed to enhance the push phase might not reflect performance improvements. The recruitment of younger athletes and an increase of youthful competitive activity may be another effective way to reach international competitive results.

  16. A Robust Iris Identification System Based on Wavelet Packet Decomposition and Local Comparisons of the Extracted Signatures

    Directory of Open Access Journals (Sweden)

    Rossant Florence

    2010-01-01

    Full Text Available Abstract This paper presents a complete iris identification system including three main stages: iris segmentation, signature extraction, and signature comparison. An accurate and robust pupil and iris segmentation process, taking into account eyelid occlusions, is first detailed and evaluated. Then, an original wavelet-packet-based signature extraction method and a novel identification approach, based on the fusion of local distance measures, are proposed. Performance measurements validating the proposed iris signature and demonstrating the benefit of our local-based signature comparison are provided. Moreover, an exhaustive evaluation of robustness, with regards to the acquisition conditions, attests the high performances and the reliability of our system. Tests have been conducted on two different databases, the well-known CASIA database (V3 and our ISEP database. Finally, a comparison of the performances of our system with the published ones is given and discussed.

  17. Cluster carburizing. Final report, June 1, 1973-May 31, 1979

    International Nuclear Information System (INIS)

    Morral, J.E.

    1979-05-01

    Three major accomplishments of the cluster carburizing program were showing that the hardness of aged and carburized materials could be controlled via the aged structure; developing a new and analytical theory of subscale formation; and characterizing the properties of Ta-Hf alloys with respect to precipitation kinetics and morphology, diffusion kinetics, age hardening, and subscale formation. The first of these verified the cluster carburizing concept, which has potential use in the development of high strength materials. The second has applications in the fields of hot corrosion, oxidation, and high temperature coatings. The third provided necessary background for this study and provided a further understanding of the behavior of refractory metals. Details about the above are contained in this final report as well as comments on the Ta-Hf, TaC-HfC and NbC-HfC phase diagrams, a comparison of hardening in the Nb-Hf and Ta-Hf system, and a discussion of possible future work

  18. Comparison between direct transesterification of microalgae and hydrochar

    Directory of Open Access Journals (Sweden)

    Vo Thanh Phuoc

    2017-07-01

    Full Text Available Hydrothermal carbonization (HTC of microalgae is one of processes that can effectively remove moisture from microalgae. In addition, the hydrochar retains most of fatty acids from microalgae feedstock, and the content of fatty acids in hydrochar is doubled. This research concentrates on the comparison between direct transesterification of microalgae and hydrochar. The result shows that the biodiesel yields of hydrochar were higher than those of microalgae at the same reaction conditions due to the higher extraction rate of fatty acids from hydrochar. Finally, the amount of methanol and catalyst which is required for a given amount of microalgae can be reduced to a half through the direct transesterification of hydrochar.

  19. Symposium on cross national comparisons: Youth population surveys about child maltreatment

    DEFF Research Database (Denmark)

    Helweg-Larsen, Karin; Larsen, Helmer Bøving

    Cross National Comparisons: Youth Population Surveys About Child Maltreatment In this multi-session track, researchers will present the results concerning the epidemiology of child maltreatment from over one dozen general population surveys of youth, covering four continents and portions...... of the world where epidemiologic data has not been previously available. Organizers will request in advance that the presenters include some data in formats that can be compared across studies. In a final session, the organizers will lead a discussion about the challenges of national surveys and cross national...

  20. Gender as a variable in the assessment of final year degree-level communication skills.

    Science.gov (United States)

    Wiskin, Connie M D; Allan, Teresa F; Skelton, John R

    2004-02-01

    To investigate possible bias due to gender combination of students, role players and examiners in a high-stakes assessment. Valid oral interactive contextualized examinations (VOICEs) is a long-station OSCE-style exam in general practice (GP). At the time of writing it consisted of 65% of the student's final GP mark. In the VOICE, students undertake six tasks--four vivas and two role-plays. "Patient" roles are taken by professional role players who work regularly on the undergraduate curriculum. During the role-play, the student's clinical competence is assessed by an observing GP examiner. The communication skills marks are awarded by the role player and the examiner together, by negotiation. Data have been recorded detailing the role player's initial marks, the examiner's initial marks and their final (awarded) agreed marks for 1024 consultations. 512 final year medical students, 28 role players and 48 examiners. There were no inclusion or exclusion criteria. All those present on exam day became part of the data. There was a significant relationship between gender and performance for some, but not all, stations. Correlations for multiple comparisons removed the significance. Female students perform better across the board than male students. While not always significant, this did affect grading. There was no significant association between the genders of role players and examiners with the question choices. There has been a significant worsening of male results since 1999. Differences exist in the way that pairs of mixed or single genders score students.

  1. Comparison of errors and stability in FDTD and FVTD

    Directory of Open Access Journals (Sweden)

    P. Leuchtmann

    2003-01-01

    Full Text Available The methods of finite-difference time-domain (FDTD and finite-volume time-domain (FVTD are well known techniques for solving electromagnetic problems. While for FDTD a number of commercial codes is available there are only few based on FVTD. However, FVTD has advantages since it allows completely unstructured meshes. This paper 1. deals with the principle errors made in both approaches and 2. gives a theoretical comparison of the (local stability of an FVTD scheme as opposed to the conventional Yee-scheme commonly used in FDTD. Finally the principles of a new FVTD program is presented. Its capabilities are demonstrated by the field of an antenna array.

  2. Comparison of Perfusion CT Software to Predict the Final Infarct Volume After Thrombectomy.

    Science.gov (United States)

    Austein, Friederike; Riedel, Christian; Kerby, Tina; Meyne, Johannes; Binder, Andreas; Lindner, Thomas; Huhndorf, Monika; Wodarg, Fritz; Jansen, Olav

    2016-09-01

    Computed tomographic perfusion represents an interesting physiological imaging modality to select patients for reperfusion therapy in acute ischemic stroke. The purpose of our study was to determine the accuracy of different commercial perfusion CT software packages (Philips (A), Siemens (B), and RAPID (C)) to predict the final infarct volume (FIV) after mechanical thrombectomy. Single-institutional computed tomographic perfusion data from 147 mechanically recanalized acute ischemic stroke patients were postprocessed. Ischemic core and FIV were compared about thrombolysis in cerebral infarction (TICI) score and time interval to reperfusion. FIV was measured at follow-up imaging between days 1 and 8 after stroke. In 118 successfully recanalized patients (TICI 2b/3), a moderately to strongly positive correlation was observed between ischemic core and FIV. The highest accuracy and best correlation are shown in early and fully recanalized patients (Pearson r for A=0.42, B=0.64, and C=0.83; P<0.001). Bland-Altman plots and boxplots demonstrate smaller ranges in package C than in A and B. Significant differences were found between the packages about over- and underestimation of the ischemic core. Package A, compared with B and C, estimated more than twice as many patients with a malignant stroke profile (P<0.001). Package C best predicted hypoperfusion volume in nonsuccessfully recanalized patients. Our study demonstrates best accuracy and approximation between the results of a fully automated software (RAPID) and FIV, especially in early and fully recanalized patients. Furthermore, this software package overestimated the FIV to a significantly lower degree and estimated a malignant mismatch profile less often than other software. © 2016 American Heart Association, Inc.

  3. Development of high field superconductors for fusion energy applications. Final report

    International Nuclear Information System (INIS)

    1985-01-01

    The purpose of this project was to develop a conductor design and a manufacturing procedure for a composite multifilamentary Nb 3 Sn conductor suitable for winding a magnet for use in a fusion energy power plant. Effort was concentrated on the design of a conductor with tubular niobium filaments in a copper matrix. Bronze in the bores of the filaments would react with the niobium to form Nb 3 Sn on the inside diameter of the niobium tubular filaments during a heat treatment at final size. Four filament geometries were evaluated. The addition of titanium to the bronze was found to increase the current density. The use of a hydrogen atmosphre did not appear to cause any increase in current density. Primary billets were assembled and extruded with five tubular filament designs and for comparison, five rod type filament designs. Billet designs are described

  4. 5 CFR 1216.206 - Final determination.

    Science.gov (United States)

    2010-01-01

    ... 5 Administrative Personnel 3 2010-01-01 2010-01-01 false Final determination. 1216.206 Section... PROCEEDINGS Demands or Requests for Testimony and Production of Documents § 1216.206 Final determination. The General Counsel makes the final determination on demands to requests to employees for production of...

  5. 45 CFR 150.219 - Final determination.

    Science.gov (United States)

    2010-10-01

    ... 45 Public Welfare 1 2010-10-01 2010-10-01 false Final determination. 150.219 Section 150.219... Are Failing To Substantially Enforce HIPAA Requirements § 150.219 Final determination. If, after... the State a written notice of its final determination. The notice includes the following: (a...

  6. Automatic video shot boundary detection using k-means clustering and improved adaptive dual threshold comparison

    Science.gov (United States)

    Sa, Qila; Wang, Zhihui

    2018-03-01

    At present, content-based video retrieval (CBVR) is the most mainstream video retrieval method, using the video features of its own to perform automatic identification and retrieval. This method involves a key technology, i.e. shot segmentation. In this paper, the method of automatic video shot boundary detection with K-means clustering and improved adaptive dual threshold comparison is proposed. First, extract the visual features of every frame and divide them into two categories using K-means clustering algorithm, namely, one with significant change and one with no significant change. Then, as to the classification results, utilize the improved adaptive dual threshold comparison method to determine the abrupt as well as gradual shot boundaries.Finally, achieve automatic video shot boundary detection system.

  7. Phrase-Final Words in Greek Storytelling Speech: A Study on the Effect of a Culturally-Specific Prosodic Feature on Short-Term Memory.

    Science.gov (United States)

    Loutrari, Ariadne; Tselekidou, Freideriki; Proios, Hariklia

    2018-02-27

    Prosodic patterns of speech appear to make a critical contribution to memory-related processing. We considered the case of a previously unexplored prosodic feature of Greek storytelling and its effect on free recall in thirty typically developing children between the ages of 10 and 12 years, using short ecologically valid auditory stimuli. The combination of a falling pitch contour and, more notably, extensive final-syllable vowel lengthening, which gives rise to the prosodic feature in question, led to statistically significantly higher performance in comparison to neutral phrase-final prosody. Number of syllables in target words did not reveal substantial difference in performance. The current study presents a previously undocumented culturally-specific prosodic pattern and its effect on short-term memory.

  8. 78 FR 69817 - Polyethylene Retail Carrier Bags From Thailand: Final Court Decision and Amended Final Results of...

    Science.gov (United States)

    2013-11-21

    ... Bags From Thailand: Final Court Decision and Amended Final Results of Administrative Review of the..., which recalculated the weighted-average duty margin for polyethylene retail carrier bags (PRCBs) from... Packaging at the CIT. \\2\\ See Polyethylene Retail Carrier Bags from Thailand: Final Results and Partial...

  9. Analysis od aerosol optical depth retrieved by MODIS and MERIS and comparison with photometer data

    International Nuclear Information System (INIS)

    Bocci, E.; Bonafoni, S.; Basili, P.; Biondi, R.; Arino, O.

    2009-01-01

    In this work a validation of aerosol optical depth (AOD) value provided by two different satellite sensor (MODIS and MERIS) is proposed. A comparison between satellite and ground-based AERONET data is carried out to verify the reliability of space borne instruments. Finally the behavior of AOD is analyzed monitoring particular events such as desert dust transport occurred on the 9 of October 2004 over the Mediterranean [it

  10. Final Report

    DEFF Research Database (Denmark)

    Heiselberg, Per; Brohus, Henrik; Nielsen, Peter V.

    This final report for the Hybrid Ventilation Centre at Aalborg University describes the activities and research achievement in the project period from August 2001 to August 2006. The report summarises the work performed and the results achieved with reference to articles and reports published...

  11. Multi-Point Combustion System: Final Report

    Science.gov (United States)

    Goeke, Jerry; Pack, Spencer; Zink, Gregory; Ryon, Jason

    2014-01-01

    A low-NOx emission combustor concept has been developed for NASA's Environmentally Responsible Aircraft (ERA) program to meet N+2 emissions goals for a 70,000 lb thrust engine application. These goals include 75 percent reduction of LTO NOx from CAEP6 standards without increasing CO, UHC, or smoke from that of current state of the art. An additional key factor in this work is to improve lean combustion stability over that of previous work performed on similar technology in the early 2000s. The purpose of this paper is to present the final report for the NASA contract. This work included the design, analysis, and test of a multi-point combustion system. All design work was based on the results of Computational Fluid Dynamics modeling with the end results tested on a medium pressure combustion rig at the UC and a medium pressure combustion rig at GRC. The theories behind the designs, results of analysis, and experimental test data will be discussed in this report. The combustion system consists of five radially staged rows of injectors, where ten small scale injectors are used in place of a single traditional nozzle. Major accomplishments of the current work include the design of a Multipoint Lean Direct Injection (MLDI) array and associated air blast and pilot fuel injectors, which is expected to meet or exceed the goal of a 75 percent reduction in LTO NOx from CAEP6 standards. This design incorporates a reduced number of injectors over previous multipoint designs, simplified and lightweight components, and a very compact combustor section. Additional outcomes of the program are validation that the design of these combustion systems can be aided by the use of Computational Fluid Dynamics to predict and reduce emissions. Furthermore, the staging of fuel through the individually controlled radially staged injector rows successfully demonstrated improved low power operability as well as improvements in emissions over previous multipoint designs. Additional comparison

  12. 11 CFR 9409.9 - Final determination.

    Science.gov (United States)

    2010-01-01

    ... 11 Federal Elections 1 2010-01-01 2010-01-01 false Final determination. 9409.9 Section 9409.9... INFORMATION AND PRODUCTION OF OFFICIAL RECORDS IN LEGAL PROCEEDINGS § 9409.9 Final determination. The General Counsel will make the final determination on demands and requests to employees for production of official...

  13. 48 CFR 32.605 - Final decisions.

    Science.gov (United States)

    2010-10-01

    ... REQUIREMENTS CONTRACT FINANCING Contract Debts 32.605 Final decisions. (a) The contracting officer shall issue a final decision as required by 33.211 if— (1) The contracting officer and the contractor are unable... 48 Federal Acquisition Regulations System 1 2010-10-01 2010-10-01 false Final decisions. 32.605...

  14. Value of comprehensive renal ultrasound in children with acute urinary tract infection for assessment of renal involvement: comparison with DMSA scintigraphy and final diagnosis

    Energy Technology Data Exchange (ETDEWEB)

    Brader, Peter; Riccabona, Michael [Medical University Graz, Division of Pediatric Radiology, Department of Radiology, Graz (Austria); Schwarz, Thomas [Medical University Graz, Division of Nuclear Medicine, Department of Radiology, Graz (Austria); Seebacher, Ursula [Medical University Graz, Department of Pediatric Surgery, Graz (Austria); Ring, Ekkehard [Medical University Graz, Department of Pediatrics, Graz (Austria)

    2008-12-15

    The aim of this study was to evaluate the value of comprehensive renal ultrasound (US), i.e., combining greyscale US and amplitude-coded color Doppler sonography (aCDS), for assessment of urinary tract infection (UTI) in infants and children, compared to (1) {sup 99m}Tc DMSA scintigraphy and (2) final diagnosis. Two hundred eighty-seven children with UTI underwent renal comprehensive US and DMSA scintigraphy. The results were compared with regard to their reliability to diagnose renal involvement, using (1) DMSA scintigraphy and (2) final diagnosis as the gold standard. Sixty-seven children clinically had renal involvement. Sensitivity increased from 84.1% using only aCDS to 92.1% for the combined US approach, using DMSA scintigraphy as the reference standard. When correlated with the final diagnosis, sensitivity for DMSA scintigraphy was 92.5%; sensitivity for comprehensive US was 94.0%. Our data demonstrate an increasing sensitivity using the combination of renal greyscale US supplemented by aCDS for differentiation of upper from lower UTI. Sensitivity for DMSA and comprehensive US was similar for both methods compared to the final diagnosis. Comprehensive US should gain a more important role in the imaging algorithm of children with acute UTI, thereby reducing the radiation burden. (orig.)

  15. Value of comprehensive renal ultrasound in children with acute urinary tract infection for assessment of renal involvement: comparison with DMSA scintigraphy and final diagnosis

    International Nuclear Information System (INIS)

    Brader, Peter; Riccabona, Michael; Schwarz, Thomas; Seebacher, Ursula; Ring, Ekkehard

    2008-01-01

    The aim of this study was to evaluate the value of comprehensive renal ultrasound (US), i.e., combining greyscale US and amplitude-coded color Doppler sonography (aCDS), for assessment of urinary tract infection (UTI) in infants and children, compared to (1) 99m Tc DMSA scintigraphy and (2) final diagnosis. Two hundred eighty-seven children with UTI underwent renal comprehensive US and DMSA scintigraphy. The results were compared with regard to their reliability to diagnose renal involvement, using (1) DMSA scintigraphy and (2) final diagnosis as the gold standard. Sixty-seven children clinically had renal involvement. Sensitivity increased from 84.1% using only aCDS to 92.1% for the combined US approach, using DMSA scintigraphy as the reference standard. When correlated with the final diagnosis, sensitivity for DMSA scintigraphy was 92.5%; sensitivity for comprehensive US was 94.0%. Our data demonstrate an increasing sensitivity using the combination of renal greyscale US supplemented by aCDS for differentiation of upper from lower UTI. Sensitivity for DMSA and comprehensive US was similar for both methods compared to the final diagnosis. Comprehensive US should gain a more important role in the imaging algorithm of children with acute UTI, thereby reducing the radiation burden. (orig.)

  16. 75 FR 50930 - Final Determination To Approve Alternative Final Cover Request for the Lake County, Montana Landfill

    Science.gov (United States)

    2010-08-18

    ... Determination To Approve Alternative Final Cover Request for the Lake County, Montana Landfill AGENCY... VIII is making a final determination to approve an alternative final cover for the Lake County landfill, a municipal solid waste landfill (MSWLF) owned and operated by Lake County, Montana on the...

  17. Final report on CCQM-K27.2: Second Subsequent study: determination of ethanol in aqueous media

    Science.gov (United States)

    Schantz, Michele M.; Parris, Reenie M.; May, Willie E.; Rosso, Adriana; Puglisi, Celia; Marques Rodrigues Caixeiro, Janaína; Massiff, Gabriela; Camacho Frías, Evangelina; Pérez Urquiza, Melina; Archer, Marcellé; Visser, M. S.; deVos, Betty-Jayne

    2013-01-01

    subsequent study (nominal concentrations of 0.2 mg/g, 1 mg/g, 3 mg/g and 60 mg/g). The three participants in the CCQM-K27-Subsequent key comparison demonstrated their ability to measure ethanol in aqueous matrix in the concentration range of 0.2 mg/g to 60 mg/g. A report on this project has been approved by the CCQM and can be found at the BIPM website. A second follow-on key comparison, CCQM-K27.2 Second Subsequent, was initiated in 2006 to accommodate laboratories that had not been ready to benchmark their methods in the previous two CCQM-K27 studies. Two levels of ethanol in water were used in the second subsequent study ranging in concentration between 0.5 mg/g and 4 mg/g. Four of the five participants in the CCQM-K27.2 Second Subsequent key comparison demonstrated their ability to measure ethanol in aqueous matrix in that concentration range. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

  18. 32 CFR 536.64 - Final offers.

    Science.gov (United States)

    2010-07-01

    ... 32 National Defense 3 2010-07-01 2010-07-01 true Final offers. 536.64 Section 536.64 National... UNITED STATES Investigation and Processing of Claims § 536.64 Final offers. (a) When claims personnel... less than the amount claimed, a settlement authority will make a written final offer within his or her...

  19. Final state effects in liquid 4He: An experimental test

    International Nuclear Information System (INIS)

    Sokol, P.E.; Silver, R.N.; Sosnick, T.R.; Snow, W.M.

    1989-01-01

    Inelastic neutron scattering at high momentum transfers can provide direct information on the atomic momentum distribution n(p) when the Impulse Approximation (IA) is valid. In isotropic systems, the scattering in the IA is directly proportional to the longitudinal momentum distribution which is a function of a single scaling variable Y /triple bond/ (M/Q)(ω /minus/ ω/sub r/), where M is the mass of the scatterer, Q is the momentum transfer, and ω/sub r/ = Q 2 /2M is the recoiled energy. However, the experimentally attainable Q's are not large enough to reach the IA limit. Deviations from the IA due to final state scattering by neighboring atoms, known as final state effects, will distort the observed scattering from the IA prediction. Thus, an understanding of deviations from the IA is essential to accurate determination of n(p). Liquid helium provides an excellent testing ground for studying FSE in a dense, strongly interacting system for two reasons. First, theoretical calculations of the momentum distributions are available in both the normal liquid, and superfluid phases. These calculations are believed to be quite accurate, since they agree well with several other measured properties of the liquid. In addition, n(p) in the superfluid exhibits a very sharp feature, the Bose condensate peak, which should be very sensitive to FSE. Comparison of the predicted scattering obtained from the theoretical n(p) using the IA to the experimentally observed scattering can be used to study deviations due to FSE. 14 refs., 7 figs

  20. Deep inelastic final states

    International Nuclear Information System (INIS)

    Girardi, G.

    1980-11-01

    In these lectures we attempt to describe the final states of deep inelastic scattering as given by QCD. In the first section we shall briefly comment on the parton model and give the main properties of decay functions which are of interest for the study of semi-inclusive leptoproduction. The second section is devoted to the QCD approach to single hadron leptoproduction. First we recall basic facts on QCD log's and derive after that the evolution equations for the fragmentation functions. For this purpose we make a short detour in e + e - annihilation. The rest of the section is a study of the factorization of long distance effects associated with the initial and final states. We then show how when one includes next to leading QCD corrections one induces factorization breaking and describe the double moments useful for testing such effects. The next section contains a review on the QCD jets in the hadronic final state. We begin by introducing the notion of infrared safe variable and defining a few useful examples. Distributions in these variables are studied to first order in QCD, with some comments on the resummation of logs encountered in higher orders. Finally the last section is a 'gaullimaufry' of jet studies

  1. 36 CFR 908.33 - Final determination.

    Science.gov (United States)

    2010-07-01

    ... 36 Parks, Forests, and Public Property 3 2010-07-01 2010-07-01 false Final determination. 908.33... DEVELOPMENT AREA Review Procedure § 908.33 Final determination. (a) The Chairman or designee(s) shall make a final determination on the claim within 45 days of receipt of the file from the Director of Real Estate...

  2. Spent fuel management strategies in eight countries and applicability to Sweden. Final report

    International Nuclear Information System (INIS)

    1986-01-01

    The spent fuel management activities described in volume 1 are compared in three areas. The first section summarizes the spent fuel management options being followed in each country and compares those options with regard to cost, environmental impact and public acceptability. Next section reviews and compares national policies on nuclear power, spent fuel management and high-level waste disposal and assesses their impact on the development and licensing of nuclear power plants. The third section compares the regulatory requirements affecting spent fuel managementin terms of their overall spirit and characteristics and in terms of the responsibilities of the utilities and the regulatory authorities. Finally, the last section addresses the applicability to Sweden of the findings from these comparisons, focusing on cost efficiency, health and safety, environmental impact, public acceptance and licensing procedures

  3. Data breaches. Final rule.

    Science.gov (United States)

    2008-04-11

    This document adopts, without change, the interim final rule that was published in the Federal Register on June 22, 2007, addressing data breaches of sensitive personal information that is processed or maintained by the Department of Veterans Affairs (VA). This final rule implements certain provisions of the Veterans Benefits, Health Care, and Information Technology Act of 2006. The regulations prescribe the mechanisms for taking action in response to a data breach of sensitive personal information.

  4. WEXA: exergy analysis for increasing the efficiency of air/water heat pumps - Final report

    Energy Technology Data Exchange (ETDEWEB)

    Gasser, L.; Wellig, B.; Hilfiker, K.

    2008-04-15

    This comprehensive final report for the Swiss Federal Office of Energy (SFOE) presents the results of a study at the made by the Engineering and Architecture department at the Lucerne University of Applied Sciences and Arts. The subject of the WEXA study (Waermepumpen-Exergie-Analyse - heat pump exergy analysis) is the analysis of the operation of air/water heat-pumps using exergy analysis methods. The basic thermodynamics of heating systems using heat-pumps is discussed. The exergy analyses and exergy balances for the various components and processes of an air/water heat-pump are presented and discussed. Comparisons are presented for heat-pumps with on/off and continuous control systems for their compressors and fans. The paper is concluded with a collection of appendices on the subject.

  5. Resuspension created by bedload transport of macroalgae

    DEFF Research Database (Denmark)

    Canal Vergés, Paula; Kristensen, Erik; Flindt, Mogens

    2009-01-01

    surface sediment while drifting as bed load. To improve the understanding of this ballistic effect of moving plants on the sediment surface, controlled annular flume experiments were performed. Plant transport was measured together with turbidity and suspended particulate matter during increasing water...

  6. The nepheloid bottom layer and water masses at the shelf break of the western Ross Sea

    Science.gov (United States)

    Capello, Marco; Budillon, Giorgio; Cutroneo, Laura; Tucci, Sergio

    2009-06-01

    In the austral summers of 2000/2001 and 2002/2003 the Italian CLIMA Project carried out two oceanographic cruises along the northwestern margin of the Ross Sea, where the Antarctic Bottom Water forms. Here there is an interaction between the water masses on the sea floor of the outer shelf and slope with a consequent evolution of benthic nepheloid layers and an increase in total particulate matter. We observed three different situations: (a) the presence of triads (bottom structures characterized by a concomitant jump in turbidity, temperature, and salinity data) and high re-suspension phenomena related to the presence of the Circumpolar Deep Water and its mixing with cold, salty shelf waters associated with gravity currents; (b) the absence of triads with high re-suspension, implying that when the gravity currents are no longer active the benthic nepheloid layer may persist until the suspended particles settle to the sea floor, suggesting that the turbidity data can be used to study recent gravity current events; and (c) the absence of turbidity and sediment re-suspension phenomena supports the theory that a steady situation had been re-established and the current interaction no longer occurred or had finished sometime before.

  7. Comparison of Metabolic Pathways in Escherichia coli by Using Genetic Algorithms

    Directory of Open Access Journals (Sweden)

    Patricia Ortegon

    2015-01-01

    Full Text Available In order to understand how cellular metabolism has taken its modern form, the conservation and variations between metabolic pathways were evaluated by using a genetic algorithm (GA. The GA approach considered information on the complete metabolism of the bacterium Escherichia coli K-12, as deposited in the KEGG database, and the enzymes belonging to a particular pathway were transformed into enzymatic step sequences by using the breadth-first search algorithm. These sequences represent contiguous enzymes linked to each other, based on their catalytic activities as they are encoded in the Enzyme Commission numbers. In a posterior step, these sequences were compared using a GA in an all-against-all (pairwise comparisons approach. Individual reactions were chosen based on their measure of fitness to act as parents of offspring, which constitute the new generation. The sequences compared were used to construct a similarity matrix (of fitness values that was then considered to be clustered by using a k-medoids algorithm. A total of 34 clusters of conserved reactions were obtained, and their sequences were finally aligned with a multiple-sequence alignment GA optimized to align all the reaction sequences included in each group or cluster. From these comparisons, maps associated with the metabolism of similar compounds also contained similar enzymatic step sequences, reinforcing the Patchwork Model for the evolution of metabolism in E. coli K-12, an observation that can be expanded to other organisms, for which there is metabolism information. Finally, our mapping of these reactions is discussed, with illustrations from a particular case.

  8. Final focus system for TLC

    International Nuclear Information System (INIS)

    Oide, K.

    1988-11-01

    A limit of the chromaticity correction for the final focus system of a TeV Linear Collider (TLC) is investigated. As the result, it becomes possible to increase the aperture of the final doublet with a small increase of the horizontal β function. The new optics design uses a final doublet of 0.5 mm half-aperture and 1.4 T pole-tip field. The length of the system is reduced from 400 m to 200 m by several optics changes. Tolerances for various machine errors with this optics are also studied. 5 refs., 7 figs., 2 tabs

  9. Overview: clinical and physiological comparison of meditation with other self-control strategies.

    Science.gov (United States)

    Shapiro, D H

    1982-03-01

    In 1977 the American Psychiatric Association called for a critical examination of the clinical effectiveness of meditation. The author provides a review of the literature bearing on clinical and physiological comparisons of meditation with other self-control strategies. He begins by providing a definition of mediation and then cites the literature comparing mediation with such self-regulation strategies as biofeedback, hypnosis, and progressive relaxation. He pays particular attention to the "uniqueness" of mediation as a clinical intervention strategy a well as the adverse effects of meditation. Finally, he offers suggestions and guidelines for future research.

  10. [Ethics of research in psychiatry. Comparison of France and the United States].

    Science.gov (United States)

    Lemoine, P; Pacault-Legendre, V

    1983-01-01

    This article presents a comparison of research ethics in psychopharmacology in France and the United States. The authors present some elements of definition, etymology and of history. In addition, they study how this very specific research is actually done. Many questions are discussed, including the right of the patient, and the problem of normal volunteers. Other aspects are more technical i.e. remuneration, protocol, and the product. Finally the role of the ethics committees is investigated. These committees comprise the third component of the trial that consists of the research and the subject.

  11. Comparison between calculation and measurement of energy deposited by 800 MeV protons

    International Nuclear Information System (INIS)

    Loewe, W.E.

    1980-01-01

    The High Energy Transport Code, HETC, was obtained from the Radiation Shielding Information Center (RSIC) at Oak Ridge National Laboratory and altered as necessary to run on a CDC 7600 using the LTSS software in use at LLNL. HETC was then used to obtain calculated estimates of energy deposited, for comparison with a series of benchmark experiments done by LLNL. These experiments used proton beams of various energies incident on well-defined composite targets in good geometry. In this report, two aspects of the comparison between calculated and experimental energy depositions from an 800 MeV proton beam are discussed. Both aspects involve the fact that workers at SAI had previously used their version of HETC to calculate this experiment and reported their comparison with the measured data. The first aspect addressed is that their calculated data and LLNL calculations do not agree, suggesting an error in the conversion process from the RSIC code. The second aspect is not independent of the first, but is of sufficient importance to merit separate emphasis. It is that the SAI calculations agree well with experiments at the detector plate located some distance from the shower plate, whereas the LLNL calculations show a clearcut discrepancy there in comparison with the experiment. A contract was let in January 1980 by LLNL with SAI in order to obtain full details on the two cited aspects of the comparison between calculated and experimental energy depositions from an 800 MeV proton beam. The ensuing discussion is based on the final report of that contracted work

  12. Cassini's Grand Finale Overview

    Science.gov (United States)

    Spilker, L. J.

    2017-12-01

    After 13 years in orbit, the Cassini-Huygens Mission to Saturn ended in a science-rich blaze of glory. Cassini sent back its final bits of unique science data on September 15, 2017, as it plunged into Saturn's atmosphere, vaporizing and satisfying planetary protection requirements. Cassini's final phase covered roughly ten months and ended with the first time exploration of the region between the rings and planet. In late 2016 Cassini transitioned to a series of 20 Ring Grazing orbits with peripases just outside Saturn's F ring, providing close flybys of tiny ring moons, including Pan, Daphnis and Atlas, and high-resolution views of Saturn's A and F rings. A final Titan flyby in late April 2017 propelled Cassini across Saturn's main rings and into its Grand Finale orbits. Comprised of 22 orbits, Cassini repeatedly dove between Saturn's innermost rings and upper atmosphere to answer fundamental questions unattainable earlier in the mission. The last orbit turned the spacecraft into the first Saturn atmosphere probe. The Grand Finale orbits provided highest resolution observations of both the rings and Saturn, and in-situ sampling of the ring particle composition, Saturn's atmosphere, plasma, and innermost radiation belts. The gravitational field was measured to unprecedented accuracy, providing information on the interior structure of the planet, winds in the deeper atmosphere, and mass of the rings. The magnetic field provided insight into the physical nature of the magnetic dynamo and structure of the internal magnetic field. The ion and neutral mass spectrometer sampled the upper atmosphere for molecules that escape the atmosphere in addition to molecules originating from the rings. The cosmic dust analyzer directly sampled the composition from different parts of the main rings for the first time. Fields and particles instruments directly measured the plasma environment between the rings and planet. Science highlights and new mysteries collected in the Grand

  13. National comparison on volume sample activity measurement methods

    International Nuclear Information System (INIS)

    Sahagia, M.; Grigorescu, E.L.; Popescu, C.; Razdolescu, C.

    1992-01-01

    A national comparison on volume sample activity measurements methods may be regarded as a step toward accomplishing the traceability of the environmental and food chain activity measurements to national standards. For this purpose, the Radionuclide Metrology Laboratory has distributed 137 Cs and 134 Cs water-equivalent solid standard sources to 24 laboratories having responsibilities in this matter. Every laboratory has to measure the activity of the received source(s) by using its own standards, equipment and methods and report the obtained results to the organizer. The 'measured activities' will be compared with the 'true activities'. A final report will be issued, which plans to evaluate the national level of precision of such measurements and give some suggestions for improvement. (Author)

  14. Final report on COOMET.RI(II)-S2.Cs-137 (319/RU/04): Comparison measurements of radionuclide volume sources (Cs-137)

    International Nuclear Information System (INIS)

    Korostin, S.; Hernandez, T.; Oropesa, P.; Arnold, D.; Evseev, V.; Ivanukovich, A.; Milevskiy, V.; Svec, A.; Lapenas, A.; Andonova, V.; Steiner, V.

    2010-01-01

    Measurements of the Cs-137 specific activity in artificial volume material of water density were performed in nine laboratories with HPGe spectrometry technique. Analysis of the gamma radiation absorption in measured material and in the most important for environmental monitoring substances (food, water, biological materials, soils) confirmed the Compton scattering as the main mechanism of interaction. The list of CMCs supported by the comparison is suggested. (authors)

  15. Final report on COOMET.RI(II)-S2.Cs-137 (319/RU/04): Comparison measurements of radionuclide volume sources (Cs-137)

    Energy Technology Data Exchange (ETDEWEB)

    Korostin, S. [All Russian Research Institute for Physical-Technical and Radio-Technical Measurements (VNIIFTRI), Mendeleevo (Russian Federation); Hernandez, T.; Oropesa, P. [Center of Isotopes - Radionuclide Metrology Department (CENTIS-DMR), Habana (Cuba); Arnold, D. [Physikalisch-Technische Bundesanstalt (PTB), Braunschweig (Germany); Evseev, V. [National Scientific Centre ' Institute of Metrology' (NSC IM), Kharkov (Ukraine); Ivanukovich, A.; Milevskiy, V. [Belarusian State Institute of Metrology (BelGIM), Minsk (Belarus); Svec, A. [Slovak Institute of Metrology (SMU), Bratislava (Slovakia); Lapenas, A. [Latvian National Metrology Centre Ltd, Radiation Metrology and Testing Centre (RMTC), Salaspils (Latvia); Andonova, V. [Bulgarian Institute of Metrology - National Centre of Metrology (BIM-NCM), Sofia (Bulgaria); Steiner, V. [Ministry of the Environment - Radiation and Noise Division (ISR-MoE), Jerusalem (Israel)

    2010-04-15

    Measurements of the Cs-137 specific activity in artificial volume material of water density were performed in nine laboratories with HPGe spectrometry technique. Analysis of the gamma radiation absorption in measured material and in the most important for environmental monitoring substances (food, water, biological materials, soils) confirmed the Compton scattering as the main mechanism of interaction. The list of CMCs supported by the comparison is suggested. (authors)

  16. Final report on fourth interlaboratory comparison exercise for δ2H and δ18O analysis of water samples (WICO2011)

    International Nuclear Information System (INIS)

    Ahmad, M.; Aggarwal, P.; Duren, M. van; Poltenstein, L.; Araguas, L.; Kurttas, T.; Wassenaar, L.I.

    2012-01-01

    The IAEA Isotope Hydrology Laboratory organized the fourth interlaboratory comparison exercise for laboratories engaged in routine analysis of hydrogen and oxygen stable isotope composition of water samples in 2011. Three similar exercises were carried out in 1995, in 1999 and in 2002. However, the tradition of IAEA water stable isotope inter-laboratory comparison is much older. Two interlaboratory comparison trials for isotope hydrology laboratories were carried out in the sixties and seventies, which revealed problems with use of the NBS-1 international standard; these data were used to calibrate the newly produced primary reference materials VSMOW and SLAP. The WICO2011 exercise was announced in February 2011 on the internet, via the ISOGEOCHEM news group of Isogeochemistry and by email to all participants of the former intercomparisons. Altogether 174 laboratories expressed interest to participate in the exercise. Four water samples prepared and calibrated at the IAEA Isotope Hydrology Laboratory were labelled IAEA-OH-13 to IAEA-OH-16, which are referred to in this report as OH-13 to OH-16. By the end of the reporting deadline (the end of August 2011) altogether 137 laboratories from 53 countries had submitted 172 datasets back to the IAEA on the oxygen and hydrogen isotopic composition of these water samples. The four water samples cover the range of δ18O and δ2H values typical for the majority of natural waters. The samples were bottled from 30 L stainless steel storage barrels into 30 mL securely-capped brown glass bottles, serially numbered at the time of filling. Each laboratory received a set of four samples with a corresponding code. This code (assigned randomly) forms the Identification (ID) code used throughout the exercise and in the tables and graphs of this report for each laboratory. The ID code is not related to the order of the list of participating laboratories. The identity of participating laboratories will not be revealed unless each

  17. Brazilian energy balance 2011 - year 2010. Final report; Balanco energetico nacional 2011 - ano base 2010. Relatorio final

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2011-07-01

    The Brazilian energy balance - BEB - is divided into eight chapters and ten annexes, whose contents are as follow: chapter 1 - Energy Analysis and Aggregated Data - presents energy highlights per source in 2010 and analyses the evolution of the internal offer of energy and its relationship with economic growth in 2010; chapter 2 - Energy Supply and Demand by Source - has the accountancy, per primary and secondary energy sources, of the production, import, export, variation of stocks, losses, adjustments, desegregated total per socioeconomic sector in the country; chapter 3 - Energy Consumption by Sector - presents the final energy consumption classified by primary and secondary source for each sector of the economy; chapter 4 - Energy Imports and Exports - presents the evolution of the data on the import and export of energy and the dependence on external energy; chapter 5 - Balance of Transformation Centers - presents the energy balances for the energy transformation centers including their losses; chapter 6 - Energy Resources and Reserves - has the basic concepts use in the survey of resources and reserves of primary energy sources, with the evolution of the data from 1974 to 2010, through graphs and tables; chapter 7 - Energy and Socioeconomics - contains a comparison of energy, economic and population parameters, specific consumption, energy intensities, average prices and spending on petroleum imports; chapter 8 - State Energy Data - presents energy data for the states by Federal Unit, main energy source production, energy installations, reserves and hydraulic potential. (author)

  18. 77 FR 14416 - Notice of Availability of a Final Environmental Impact Statement and Final Environmental Impact...

    Science.gov (United States)

    2012-03-09

    ...In accordance with the National Environmental Policy Act of 1969, as amended (NEPA), and the Federal Land Policy and Management Act of 1976, as amended (FLPMA), the Bureau of Land Management (BLM) has prepared a Proposed California Desert Conservation Area (CDCA) Plan Amendment (PA)/Final Environmental Impact Statement (EIS) and Final Environmental Impact Report (EIR) for the Ocotillo Express Wind Energy Facility (OWEF) and by this notice is announcing the availability of the Proposed PA and Final EIS/EIR.

  19. White Dwarfs in Star Clusters: The Initial-Final Mass Relation for Stars from 0.85 to 8 M$_\\odot$

    Science.gov (United States)

    Cummings, Jeffrey; Kalirai, Jason; Tremblay, P.-E.; Ramírez-Ruiz, Enrico

    2018-01-01

    The spectroscopic study of white dwarfs provides both their mass, cooling age, and intrinsic photometric properties. For white dwarfs in the field of well-studied star clusters, this intrinsic photometry can be used to determine if they are members of that star cluster. Comparison of a member white dwarf's cooling age to its total cluster's age provides the evolutionary timescale of its progenitor star, and hence the mass. This is the initial-final mass relation (IFMR) for stars, which gives critical information on how a progenitor star evolves and loses mass throughout its lifetime, and how this changes with progenitor mass. Our work, for the first time, presents a uniform analysis of 85 white dwarf cluster members spanning from progenitor masses of 0.85 to 8 M$_\\odot$. Comparison of our work to theoretical IFMRs shows remarkable consistency in their shape but differences remain. We will discuss possible explanations for these differences, including the effects of stellar rotation.

  20. Flippin' Fluid Mechanics - Quasi-experimental Pre-test and Post-test Comparison Using Two Groups

    Science.gov (United States)

    Webster, D. R.; Majerich, D. M.; Luo, J.

    2014-11-01

    A flipped classroom approach has been implemented in an undergraduate fluid mechanics course. Students watch short on-line videos before class, participate in active in-class problem solving (in dyads), and complete individualized on-line quizzes weekly. In-class activities are designed to achieve a trifecta of: 1. developing problem solving skills, 2. learning subject content, and 3. developing inquiry skills. The instructor and assistants provide critical ``just-in-time tutoring'' during the in-class problem solving sessions. Comparisons are made with a simultaneous section offered in a traditional mode by a different instructor. Regression analysis was used to control for differences among students and to quantify the effect of the flipped fluid mechanics course. The dependent variable was the students' combined final examination and post-concept inventory scores and the independent variables were pre-concept inventory score, gender, major, course section, and (incoming) GPA. The R-square equaled 0.45 indicating that the included variables explain 45% of the variation in the dependent variable. The regression results indicated that if the student took the flipped fluid mechanics course, the dependent variable (i.e., combined final exam and post-concept inventory scores) was raised by 7.25 points. Interestingly, the comparison group reported significantly more often that their course emphasized memorization than did the flipped classroom group.

  1. Comparison of Invasive and Noninvasive Mechanical Ventilation for Patients with COPD:Randomised Prospective Study

    Directory of Open Access Journals (Sweden)

    Ivo Matic

    2008-01-01

    Full Text Available Acute respiratory failure due to chronic obstructive pulmonary disease presents an increasing problem for both health and economics in the modern world. The goal of this study was to compare invasive and noninvasive mechani-cal ventilation for patients with COPD. A prospective, randomized trial was performed in a multidisciplinary intensive care unit. Of 614 patients requiring mechanical ventilation (MV longer than 24h, after excluding those who didn′t meet the inclusion criteria, 72 patients with COPD remained the research sample. The MV procedure was per-formed using standard methods, applying two MV methods: invasive MV and noninvasive MV. Patients were ran-domized into two groups for MV application using closed, non transparent envelopes. Comparison was made based on patient characteristics, objective parameters 1h, 4h, 24h, and 48h after admission and finally treatment outcome. In patients with COPD NIMV had statistically better outcome compared to IMV with MV duration NIMV:IMV 102:187h, p < 0.001, time spent in ICU 127:233h, p < 0.001. Need for intubation/reintubation 16 (42.1%:34 (100%/4 (11.8%, p < 0.001, hospital pneumonia 2 (5.3%:18 (52.9%, p =0.001. Applying strict application protocols, and based on com-parison of objective parameters of pulmonary mechanics, biochemistry and finally treatment outcome, high advantage of NIMV method was confirmed.

  2. An efficient two-party quantum private comparison protocol with decoy photons and two-photon entanglement

    International Nuclear Information System (INIS)

    Yang Yuguang; Wen Qiaoyan

    2009-01-01

    Following some ideas of the quantum secret sharing (QSS) protocol (2008, Phys. Lett. A 372, 1957), we propose an efficient quantum private comparison (QPC) protocol for comparing information of equality with the help of a third party (TP). The protocol can ensure fairness, efficiency and security. The protocol is fair, which means that one party knows the sound result of the comparison if and only if the other one knows the result. The protocol is efficient with the help of the TP for calculating. However, the TP cannot learn any information about the players' respective private inputs and even about the comparison result and cannot collude with any player. The protocol is secure for the two players, that is, any information about their respective secret inputs will not leak except the final computation result. A precise proof of security of the protocol is presented. Applications of this protocol may include private bidding and auctions, secret ballot elections, commercial business, identification in a number of scenarios and so on

  3. Final Report: Hydrogen Storage System Cost Analysis

    Energy Technology Data Exchange (ETDEWEB)

    James, Brian David [Strategic Analysis Inc., Arlington, VA (United States); Houchins, Cassidy [Strategic Analysis Inc., Arlington, VA (United States); Huya-Kouadio, Jennie Moton [Strategic Analysis Inc., Arlington, VA (United States); DeSantis, Daniel A. [Strategic Analysis Inc., Arlington, VA (United States)

    2016-09-30

    The Fuel Cell Technologies Office (FCTO) has identified hydrogen storage as a key enabling technology for advancing hydrogen and fuel cell power technologies in transportation, stationary, and portable applications. Consequently, FCTO has established targets to chart the progress of developing and demonstrating viable hydrogen storage technologies for transportation and stationary applications. This cost assessment project supports the overall FCTO goals by identifying the current technology system components, performance levels, and manufacturing/assembly techniques most likely to lead to the lowest system storage cost. Furthermore, the project forecasts the cost of these systems at a variety of annual manufacturing rates to allow comparison to the overall 2017 and “Ultimate” DOE cost targets. The cost breakdown of the system components and manufacturing steps can then be used to guide future research and development (R&D) decisions. The project was led by Strategic Analysis Inc. (SA) and aided by Rajesh Ahluwalia and Thanh Hua from Argonne National Laboratory (ANL) and Lin Simpson at the National Renewable Energy Laboratory (NREL). Since SA coordinated the project activities of all three organizations, this report includes a technical description of all project activity. This report represents a summary of contract activities and findings under SA’s five year contract to the US Department of Energy (Award No. DE-EE0005253) and constitutes the “Final Scientific Report” deliverable. Project publications and presentations are listed in the Appendix.

  4. Inter-comparison between HERMESv2.0 and TNO-MACC-II emission data using the CALIOPE air quality system (Spain)

    Science.gov (United States)

    Guevara, Marc; Pay, María Teresa; Martínez, Francesc; Soret, Albert; Denier van der Gon, Hugo; Baldasano, José M.

    2014-12-01

    This work examines and compares the performance of two emission datasets on modelling air quality concentrations for Spain: (i) the High-Elective Resolution Modelling Emissions System (HERMESv2.0) and (ii) the TNO-MACC-II emission inventory. For this purpose, the air quality system CALIOPE-AQFS (WRF-ARW/CMAQ/BSC-DREAM8b) was run over Spain for February and June 2009 using the two emission datasets (4 km × 4 km and 1 h). Nitrogen dioxide (NO2), sulphur dioxide (SO2), Ozone (O3) and particular matter (PM10) modelled concentrations were compared with measurements at different type of air quality stations (i.e. rural background, urban, suburban industrial). A preliminary emission comparison showed significant discrepancies between the two datasets, highlighting an overestimation of industrial emissions in urban areas when using TNO-MACC-II. However, simulations showed similar performances of both emission datasets in terms of air quality. Modelled NO2 concentrations were similar between both datasets at the background stations, although TNO-MACC-II presented lower underestimations due to differences in industrial, other mobile sources and residential emissions. At Madrid urban stations NO2 was significantly underestimated in both cases despite the fact that HERMESv2.0 estimates traffic emissions using a more local information and detailed methodology. This NO2 underestimation problem was not found in Barcelona due to the influence of international shipping emissions located in the coastline. An inadequate characterization of some TNO-MACC-II's point sources led to high SO2 biases at industrial stations, especially in northwest Spain where large facilities are grouped. In general, surface O3 was overestimated regardless of the emission dataset used, depicting the problematic of CMAQ on overestimating low ozone at night. On the other hand, modelled PM10 concentrations were less underestimated in urban areas when applying HERMESv2.0 due to the inclusion of road dust

  5. Modelling the transport of sediments and plutonium from the Mururoa lagoon

    International Nuclear Information System (INIS)

    Rajar, R.; Zagar, D.

    1999-01-01

    The paper deals with the three-dimensional simulation of resuspension and transport of sediments from the Mururoa lagoon into the Pacific Ocean. These sediments were contaminated mainly by plutonium during French nuclear tests (from 1966 to 1996). Two cases were simulated: 'Normal conditions', taking into account permanent action of trade winds and tides and 'storm conditions', where the effect of a tropical cyclone with maximum wind velocity of 150 km/h and with a frequency of 1 storm per 10 years is simulated. The final results show, that the normal conditions cause an annual outflow of 8 x 10 4 tons of sediment and 8 GBq of plutonium, while one tropical cyclone would cause outflow of 3.9 x 10 6 tons of sediment and about 0.7 TBq of plutonium. (author)

  6. KEY COMPARISON: CCQM-K61: Quantitation of a linearised plasmid DNA, based on a matched standard in a matrix of non-target DNA

    Science.gov (United States)

    Woolford, Alison; Holden, Marcia; Salit, Marc; Burns, Malcolm; Ellison, Stephen L. R.

    2009-01-01

    Key comparison CCQM-K61 was performed to demonstrate and document the capability of interested national metrology institutes in the determination of the quantity of specific DNA target in an aqueous solution. The study provides support for the following measurement claim: "Quantitation of a linearised plasmid DNA, based on a matched standard in a matrix of non-target DNA". The comparison was an activity of the Bioanalysis Working Group (BAWG) of the Comité Consultatif pour la Quantité de Matière and was coordinated by NIST (Gaithersburg, USA) and LGC (Teddington, UK). The following laboratories (in alphabetical order) participated in this key comparison. DMSC (Thailand); IRMM (European Union); KRISS (Republic of Korea); LGC (UK); NIM (China); NIST (USA); NMIA (Australia); NMIJ (Japan); VNIIM (Russian Federation) Good agreement was observed between the reported results of all nine of the participants. Uncertainty estimates did not account fully for the dispersion of results even after allowance for possible inhomogeneity in calibration materials. Preliminary studies suggest that the effects of fluorescence threshold setting might contribute to the excess dispersion, and further study of this topic is suggested Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

  7. Hourly Comparison of GPM-IMERG-Final-Run and IMERG-Real-Time (V-03) over a Dense Surface Network in Northeastern Austria

    Science.gov (United States)

    Sharifi, Ehsan; Steinacker, Reinhold; Saghafian, Bahram

    2017-04-01

    Accurate quantitative daily precipitation estimation is key to meteorological and hydrological applications in hazards forecast and management. In-situ observations over mountainous areas are mostly limited, however, currently available satellite precipitation products can potentially provide the precipitation estimation needed for meteorological and hydrological applications. Over the years, blended methods that use multi-satellites and multi-sensors have been developed for estimating of global precipitation. One of the latest satellite precipitation products is GPM-IMERG (Global Precipitation Measurement with 30-minute temporal and 0.1-degree spatial resolutions) which consists of three products: Final-Run (aimed for research), Real-Time early run, and Real-Time late run. The Integrated Multisatellite Retrievals for GPM (IMERG) products built upon the success of TRMM's Multisatellite Precipitation Analysis (TMPA) products continue to make improvements in spatial and temporal resolutions and snowfall estimates. Recently, researchers who evaluated IMERG-Final-Run V-03 and other precipitation products indicated better performance for IMERG-Final-Run against other similar products. In this study two GPM-IMERG products, namely final run and real time-late run, were evaluated against a dense synoptic stations network (62 stations) over Northeastern Austria for mid-March 2015 to end of January 2016 period at hourly time-scale. Both products were examined against the reference data (stations) in capturing the occurrence of precipitation and statistical characteristics of precipitation intensity. Both satellite precipitation products underestimated precipitation events of 0.1 mm/hr to 0.4 mm/hr in intensity. For precipitations 0.4 mm/hr and greater, the trend was reversed and both satellite products overestimated than station recorded data. IMERG-RT outperformed IMERG-FR for precipitation intensity in the range of 0.1 mm/hr to 0.4 mm/hr while in the range of 1.1 to 1.8 mm

  8. Search for Resonances Decaying to Dijet Final States at $\\sqrt{s} = 8$ TeV with Scouting Data

    CERN Document Server

    CMS Collaboration

    2015-01-01

    A search for resonances decaying to dijet final states is performed in pp collisions at a center-of-mass energy $\\sqrt{s}=8$ TeV. Using a loose online data selection and a reduced data format collected with a novel technique called $\\textit{data scouting}$, the search extends to low-mass values, testing previously unprobed low couplings. No evidence for a signal is found. The result is interpreted as upper limits on the production cross section as a function of the resonance mass. These limits are translated into an upper limit on the resonance coupling, allowing a comparison with results obtained in the same mass region at lower collision energies.

  9. Guideline for Achieving a Target Share of Renewable Energy in Final Energy Consumption in Slovenia Until 2020

    International Nuclear Information System (INIS)

    Brecevic, Dj.

    2009-01-01

    European parliament's and Council for energy usage from renewable sources promotion's directive proposal determines acceptation of National action plan for every member state. General national goal for renewable energy share in final consumption in year 2020, defined in proposal, is 25 % energy from renewable sources in final energy consumption. Paper presents plan for renewable energy sources usage in electricity production and activities, which will be necessary to be held by organizations, which are carriers of energy activities, for building new capacities or rebuilding existing ones for electricity production from renewable energy sources. Purpose of plan is additional 3.000 GWh electricity production in year 2020 in comparison with today's electricity production from renewable energy sources. Accepted goal will be obligatory for organizations as carriers of energy activities for their social responsibility for obligations fulfillment and determined goals achievement. Report represents necessary steps that state has to make to reach bigger interest of investors for renewable energy investments and special attention is stressed on completion of regulation with goal to create suitable platform for future investors.(author).

  10. Bone age estimation and prediction of final height in patients with {beta}-thalassaemia major: a comparison between the two most common methods

    Energy Technology Data Exchange (ETDEWEB)

    Christoforidis, Athanasios; Katzos, George; Athanassiou-Metaxa, Miranda [Aristotle University of Thessaloniki, 1st Paediatric Department, Thessaloniki (Greece); Badouraki, Maria [Ippokratio Hospital, Paediatric Radiology Department, Thessaloniki (Greece)

    2007-12-15

    Thalassaemic patients are in need of frequent assessment of bone age because of growth failure and pubertal disorders. To compare the ''rapid'' Greulich and Pyle (G and P) method with the third edition of the Tanner and Whitehouse (TW3) method for determining skeletal maturity and predicting final height in thalassaemic patients. A total of 191 radiographs from 58 patients (28 male, 30 female) were retrospectively evaluated by two investigators, one for each method. In 47 radiographs from 15 patients having attained their adult height, predicted final height was calculated according to each method. The mean bone ages determined by both the G and P and TW3 methods were lower than mean chronological age, although the differences were not statistically significant (10.04 {+-} 3.69 years and 9.98 {+-} 3.39 years vs. 10.78 {+-} 3.96 years, respectively). Both methods had a tendency to over-estimate final height. Overall, the TW3 method seemed to be more accurate than the G and P method (mean absolute error 3.21 {+-} 2.51 years vs. 3.99 {+-} 2.99 years, respectively, P=0.048). The same method should be used when serial assessments are performed, as both methods provide similarly reliable, although not equivalent, results. The TW3 height prediction method seemed to be more accurate in patients with {beta}-thalassaemia major than the G and P method, albeit with a large confidence interval. (orig.)

  11. Bone age estimation and prediction of final height in patients with β-thalassaemia major: a comparison between the two most common methods

    International Nuclear Information System (INIS)

    Christoforidis, Athanasios; Katzos, George; Athanassiou-Metaxa, Miranda; Badouraki, Maria

    2007-01-01

    Thalassaemic patients are in need of frequent assessment of bone age because of growth failure and pubertal disorders. To compare the ''rapid'' Greulich and Pyle (G and P) method with the third edition of the Tanner and Whitehouse (TW3) method for determining skeletal maturity and predicting final height in thalassaemic patients. A total of 191 radiographs from 58 patients (28 male, 30 female) were retrospectively evaluated by two investigators, one for each method. In 47 radiographs from 15 patients having attained their adult height, predicted final height was calculated according to each method. The mean bone ages determined by both the G and P and TW3 methods were lower than mean chronological age, although the differences were not statistically significant (10.04 ± 3.69 years and 9.98 ± 3.39 years vs. 10.78 ± 3.96 years, respectively). Both methods had a tendency to over-estimate final height. Overall, the TW3 method seemed to be more accurate than the G and P method (mean absolute error 3.21 ± 2.51 years vs. 3.99 ± 2.99 years, respectively, P=0.048). The same method should be used when serial assessments are performed, as both methods provide similarly reliable, although not equivalent, results. The TW3 height prediction method seemed to be more accurate in patients with β-thalassaemia major than the G and P method, albeit with a large confidence interval. (orig.)

  12. Comparison of effects of training programs for final year nursing students in Turkey: differences in self-efficacy with regard to information literacy.

    Science.gov (United States)

    Özbıçakçı, Şeyda; Gezer, Nurdan; Bilik, Özlem

    2015-02-01

    Information literate person are aware of where and how they can obtain the information they need. Little is known about student nurses information literacy skills in different education programs. To find out how final year nursing students rated their own abilities to acquire new information. This study used comparative and descriptive cross-sectional surveys. Participants were final year students in two different programs, in two different universities in Turkey. The study sample consisted of final year nursing students who received training in Classic Learning (N: 61) and Problem-Based Learning (N: 96). As an evaluation instrument for the perceptions of the students their own information literacy, a scale consisting of 28 questions with 7 Likert ratings for each was used (min: 28, max: 196). The return rates of the surveys were 96.7% in the school with classic training and 81.2% in the school with PBL. It was found that the average scores of the students were high, with a mean of 137±29 in the school where the classic training program was carried out, and 163±21 in the school where the training was PBL. A statistically significant difference was found by comparing the average scores of the two independent groups (t : -6.0; pinformation literacy. We conclude that training programs should be reviewed, and new methods should be developed based on these concepts. Copyright © 2014 Elsevier Ltd. All rights reserved.

  13. Final Focus Systems in Linear Colliders

    International Nuclear Information System (INIS)

    Raubenheimer, Tor

    1998-01-01

    In colliding beam facilities, the ''final focus system'' must demagnify the beams to attain the very small spot sizes required at the interaction points. The first final focus system with local chromatic correction was developed for the Stanford Linear Collider where very large demagnifications were desired. This same conceptual design has been adopted by all the future linear collider designs as well as the SuperConducting Supercollider, the Stanford and KEK B-Factories, and the proposed Muon Collider. In this paper, the over-all layout, physics constraints, and optimization techniques relevant to the design of final focus systems for high-energy electron-positron linear colliders are reviewed. Finally, advanced concepts to avoid some of the limitations of these systems are discussed

  14. MFT homogeneity study at TNX: Final report on the low weight percent solids concentration

    International Nuclear Information System (INIS)

    Jenkins, W.J.

    1993-01-01

    A statistical design and analysis of both elemental analyses and weight percent solids analyses data was utilized to evaluate the MFT homogeneity at low heel levels and low agitator speed at both high and low solids feed concentrations. The homogeneity was also evaluated at both low and high agitator speed at the 6000+ gallons static level. The dynamic level portion of the test simulated feeding the Melter from the MFT to evaluate the uniformity of the solids slurry composition (Frit-PHA-Sludge) entering the melter from the MFT. This final report provides the results and conclusions from the second half of the study, the low weight percent solids concentration portion, as well as a comparison with the results from the first half of the study, the high weight percent solids portion

  15. ISP42 (PANDA Tests) - Open Phase Comparison Report

    International Nuclear Information System (INIS)

    2003-05-01

    of ISP-42 by 8 organizations from 8 countries. These 'open' phase calculations were performed using computer codes RELAP5/Mod3.2, CATHARE2 V1.4 (Rev.6), SPECTRA, COCOSYS, RALOC mod4.0, GOTHIC 6.Ip3. The detailed comparisons and analysis of the 'open' phase of the ISP-42 were completed and a draft report on the results of the 'open' phase was issued before the final workshop. Final Workshop on the 'open' phase calculations comparison to experimental data had been organised at PSI from 19 to 21 November 2001 with 16 participants. The draft comparison report on the 'open' phase of the ISP-42 was presented and discussed in detail with the participants. Improvements on the cases submitted were observed with the recent versions of the codes, use of some other physical models (e.g., heat transfer with noncondensable) and re-nodalization of the system depending on the six phases of the ISP-42. In addition to the good results obtained in the 'blind' phase, these improvements also provided mostly good agreements with the test results. Some of the prediction cases still differed significantly, where 3D phenomena simulation (e.g., mixing, stratification in large vessels, etc.) starts to be the dominating factor in the transient, for these cases the reasons of differences were identified to some limited degree. The general conclusions including recommendations of the six phases of the ISP-42 post test cases and also covering the 'blind' phase results are summarized in this report

  16. Evaluation of surficial sediment toxicity and sediment physico-chemical characteristics of representative sites in the Lagoon of Venice (Italy)

    Science.gov (United States)

    Losso, C.; Arizzi Novelli, A.; Picone, M.; Marchetto, D.; Pessa, G.; Molinaroli, E.; Ghetti, P. F.; Volpi Ghirardini, A.

    2004-11-01

    Toxic hazard in sites with varying types and levels of contamination in the Lagoon of Venice was estimated by means of toxicity bioassays based on the early life-stages of the autochthonous sea urchin Paracentrotus lividus. Elutriate was chosen as the test matrix, due to its ability to highlight potential toxic effects towards sensitive biological components of the water column caused by sediment resuspension phenomena affecting the Lagoon. Surficial sediments (core-top 5 cm deep), directly influenced by resuspension/redeposition processes, and core sediments (core 20 cm deep), recording time-mediated contamination, were sampled in some sites located in the lagoonal area most greatly influenced by anthropogenic activities. Particle size, organic matter and water content were also analysed. In two sites, the results of physical parameters showed that the core-top sediments were coarser than the 20-cm core sediments. Sperm cell toxicity test results showed the negligible acute toxicity of elutriates from all investigated sites. The embryo toxicity test demonstrated a short-term chronic toxicity gradient for elutriates from the 20-cm core sediments, in general agreement both with the expected contamination gradient and with results of the Microtox® solid-phase test. Elutriates of the core-top 5-cm sediments revealed a totally inverted gradient, in comparison with that for the 20-cm core sediments, and the presence of a "hot spot" of contamination in the site chosen as a possible reference. Investigations on ammonia and sulphides as possible confounding factors excluded their contribution to this "hot spot". Integrated physico-chemical and toxicity results on sediments at various depths demonstrated the presence of disturbed sediments in the central basin of the Lagoon of Venice.

  17. Energy efficiency in Norway (1996). Cross Country Comparison on Energy Efficiency Indicators, Phase 4

    Energy Technology Data Exchange (ETDEWEB)

    Alm, Leif Kristian

    1998-12-01

    This is the national report for Norway in phase 4 of the SAVE project 'Cross country comparison of energy efficiency indicators'. The report deals with energy use and energy efficiency in Norway the last 20 years, with a special emphasis on the period after 1990. Final energy use per Gross Domestic Product (GDP) was reduced by approx 2.3% per year from 1990 to 1996. Doing detailed sector analysis we are applying Laspeyres indices to attribute changes in energy use to either activity, structure or intensity. Calculating an aggregate intensity index from the sector intensities gives an average intensity reduction of 0.4% per year. Thereby most of the reduction in final energy per unit GDP are due to structural changes, and not technical improvements. Almost all data are taken from official Norwegian statistics (Statistics Norway). (author)

  18. Satellite Assessment of Bio-Optical Properties of Northern Gulf of Mexico Coastal Waters Following Hurricanes Katrina and Rita

    Directory of Open Access Journals (Sweden)

    Merritt Tuel

    2008-07-01

    Full Text Available The impacts of major tropical storms events on coastal waters include sediment resuspension, intense water column mixing, and increased delivery of terrestrial materials into coastal waters. We examined satellite imagery acquired by the Moderate Resolution Imaging Spectroradiometer (MODIS ocean color sensor aboard the Aqua spacecraft following two major hurricane events: Hurricane Katrina, which made landfall on 29 August 2005, and Hurricane Rita, which made landfall on 24 September. MODIS Aqua true color imagery revealed high turbidity levels in shelf waters immediately following the storms indicative of intense resuspension. However, imagery following the landfall of Katrina showed relatively rapid return of shelf water mass properties to pre-storm conditions. Indeed, MODIS Aqua-derived estimates of diffuse attenuation at 490 nm (K_490 and chlorophyll (chlor_a from mid-August prior to the landfall of Hurricane Katrina were comparable to those observed in mid-September following the storm. Regions of elevated K_490 and chlor_a were evident in offshore waters and appeared to be associated with cyclonic circulation (cold-core eddies identified on the basis of sea surface height anomaly (SSHA. Imagery acquired shortly after Hurricane Rita made landfall showed increased water column turbidity extending over a large area of the shelf off Louisiana and Texas, consistent with intense resuspension and sediment disturbance. An interannual comparison of satellite-derived estimates of K_490 for late September and early October revealed relatively lower levels in 2005, compared to the mean for the prior three years, in the vicinity of the Mississippi River birdfoot delta. In contrast, levels above the previous three year mean were observed off Texas and Louisiana 7-10 d after the passage of Rita. The lower values of K_490 near the delta could be attributed to relatively low river discharge during the preceding months of the 2005 season. The elevated levels

  19. The costs of radiosurgical treatment: Comparison between gamma knife and linear accelerator

    International Nuclear Information System (INIS)

    Koenigsmaier, H.; Pauli-Ferch, B. de; Hackl, A.; Pendl, G.

    1998-01-01

    Radiosurgical treatment can be carried out by means of a gamma knife or a linear accelerator. The linear accelerator may be either a single-purpose appliance, exclusively employed in radiosurgery, or an adapted appliance which is used primarily for fractioned radiotherapy, and only additionally for radiosurgical purposes. The first alternative will be referred to briefly as a 'dedicated Linac', the latter as an 'adapted Linac'. Cost accounting data for these alternatives will be discussed under three main categories: investment costs. operating costs, and finally staffing costs. Costs are only considered to the extent that this is necessary to facilitate a comprehensive cost comparison. Factors for which the costs remain the same or at least broadly the same will from the outset not be taken into consideration. These include, for instance, the costs of general or special administration, diagnosis, and image processing. The results and conclusions of this study therefore cannot be employed immediately in the evaluation of cost reimbursement schemes of the type carried out by agencies responsible for social insurance. Here, appropriate complete cost analyzes especially for this purpose are required. The final comprehensive cost comparison reveals that the adapted Linac is the most favourable alternative with small annual quantities of patients. With larger numbers of patients the Gamma Knife represents the most favourable from a cost accounting angle. The dedicated Linac accordingly does not have a cost advantage for any of the examined numbers of patients. Clearly the lowest treatment costs per patient can be achieved by employing a Gamma Knife and using it to capacity. (author)

  20. Expanded studies of linear collider final focus systems at the Final Focus Test Beam

    International Nuclear Information System (INIS)

    Tenenbaum, P.G.

    1995-12-01

    In order to meet their luminosity goals, linear colliders operating in the center-of-mass energy range from 3,50 to 1,500 GeV will need to deliver beams which are as small as a few Manometers tall, with x:y aspect ratios as large as 100. The Final Focus Test Beam (FFTB) is a prototype for the final focus demanded by these colliders: its purpose is to provide demagnification equivalent to those in the future linear collider, which corresponds to a focused spot size in the FFTB of 1.7 microns (horizontal) by 60 manometers (vertical). In order to achieve the desired spot sizes, the FFTB beam optics must be tuned to eliminate aberrations and other errors, and to ensure that the optics conform to the desired final conditions and the measured initial conditions of the beam. Using a combination of incoming-beam diagnostics. beam-based local diagnostics, and global tuning algorithms, the FFTB beam size has been reduced to a stable final size of 1.7 microns by 70 manometers. In addition, the chromatic properties of the FFTB have been studied using two techniques and found to be acceptable. Descriptions of the hardware and techniques used in these studies are presented, along with results and suggestions for future research

  1. Expanded studies of linear collider final focus systems at the Final Focus Test Beam

    Energy Technology Data Exchange (ETDEWEB)

    Tenenbaum, Peter Gregory [Stanford Univ., CA (United States)

    1995-12-01

    In order to meet their luminosity goals, linear colliders operating in the center-of-mass energy range from 3,50 to 1,500 GeV will need to deliver beams which are as small as a few Manometers tall, with x:y aspect ratios as large as 100. The Final Focus Test Beam (FFTB) is a prototype for the final focus demanded by these colliders: its purpose is to provide demagnification equivalent to those in the future linear collider, which corresponds to a focused spot size in the FFTB of 1.7 microns (horizontal) by 60 manometers (vertical). In order to achieve the desired spot sizes, the FFTB beam optics must be tuned to eliminate aberrations and other errors, and to ensure that the optics conform to the desired final conditions and the measured initial conditions of the beam. Using a combination of incoming-beam diagnostics. beam-based local diagnostics, and global tuning algorithms, the FFTB beam size has been reduced to a stable final size of 1.7 microns by 70 manometers. In addition, the chromatic properties of the FFTB have been studied using two techniques and found to be acceptable. Descriptions of the hardware and techniques used in these studies are presented, along with results and suggestions for future research.

  2. Final focus nomenclature

    International Nuclear Information System (INIS)

    Erickson, R.

    1986-01-01

    The formal names and common names for all devices in the final focus system of the SLC are listed. The formal names consist of a device type designator, microprocessor designator, and a four-digit unit number

  3. Dynamics of particulate phosphorus in a shallow eutrophic lake

    Energy Technology Data Exchange (ETDEWEB)

    Shinohara, Ryuichiro, E-mail: r-shino@nies.go.jp [National Institute for Environmental Studies, 16-2 Onogawa, Tsukuba, Ibaraki 305-8506 (Japan); Imai, Akio; Kohzu, Ayato; Tomioka, Noriko [National Institute for Environmental Studies, 16-2 Onogawa, Tsukuba, Ibaraki 305-8506 (Japan); Furusato, Eiichi [Graduate School of Science and Engineering, Saitama University, 255 Shimo-okubo, Sakura-ku, Saitama 338-8570 (Japan); Satou, Takayuki; Sano, Tomoharu; Komatsu, Kazuhiro; Miura, Shingo; Shimotori, Koichi [National Institute for Environmental Studies, 16-2 Onogawa, Tsukuba, Ibaraki 305-8506 (Japan)

    2016-09-01

    We tested the hypothesis that in shallow, eutrophic Lake Kasumigaura, the concentration of particulate phosphorus (PP) is controlled by biogenic P (P in living or dead phytoplankton and bacterial cells), rather than by resuspension of inorganic P in sediment. Increases in wind velocity and turbidity were associated with bottom shear stress exceeding the critical value for the lake (τ{sub c} = 0.15 N m{sup −2}); this increased turbidity was due to sediment resuspension. However, concentrations of PP; HCl-extractable, reactive P in PP (P-rP); and HCl-extractable, non-reactive P in PP (P-nrP) were not correlated with wind velocity (PP vs. wind velocity: r = 0.40, p > 0.05). Rather, the P-nrP concentration accounted for approximately 79% of PP, and the concentrations of PP, P-rP, and P-nrP were correlated with the particulate organic carbon (POC) concentration (POC vs. PP: r = 0.90, p < 0.01; POC vs. P-rP: r = 0.82, p < 0.01; POC vs. P-nrP: r = 0.86, p < 0.01). In our {sup 31}P nuclear magnetic resonance spectroscopy results, mononucleotides accounted for the largest proportion among the detected P compound classes. In addition, concentrations of mononucleotides, orthophosphate, and pyrophosphate were significantly higher in samples with high POC concentrations, whereas the DNA-P concentration was not. These results suggest that biogenic P affects PP concentrations more strongly than does sediment resuspension, and the production of biogenic P creates a pool of mononucleotides, a class of easily degradable P, even in shallow, eutrophic Lake Kasumigaura. - Highlights: • Biogenic P affected the PP concentration more than did sediment resuspension. • PP correlated with particulate organic carbon concentration but not wind velocity. • Mononucleotides accounted for the largest P compound class of organic P in PP.

  4. FameLab - Swiss Semi Finals

    CERN Multimedia

    Corinne Pralavorio

    2012-01-01

    Twenty-two young scientists participated in the FameLab semi-final at CERN's Globe of Science and Innovation on 4 February, supported by a large audience and by more than 100 fans following via webcast. A panel of judges chose Lemmer and four other candidates to join five other semi-finalists at the national finals in Zurich on 30 March.

  5. Catarse e Final Feliz

    Directory of Open Access Journals (Sweden)

    Myriam Ávila

    2001-12-01

    Full Text Available Resumo: É a certeza de que nada mais – ou nada importante – pode acontecer após o final de um conto que permite o acontecimento da catarse. Se na maioria das narrativas existe algum tipo de dénouement, em algumas delas isso acontece de maneira especialmente satisfatória e afirmativa. O conto de fadas é uma dessas formas narrativas onde o efeito catártico é extremo e preenche objetivos específicos, de acordo com Bruno Bettelheim. Hollywood mimetizou essa forma como estratégia de sedução, iniciando a tradição do final feliz no cinema. A partir do conto de fadas Cinderela, em diferentes versões, juntamente com a animação homônima da Disney e ainda duas versões do filme Sabrina, será traçada aqui uma relação entre a catarse e o final feliz nos contos de fada, bem como seu uso pela indústria cultural. Palavras-chave: catarse, contos de fada, Hollywood

  6. Final focus nomenclature

    Energy Technology Data Exchange (ETDEWEB)

    Erickson, R.

    1986-08-08

    The formal names and common names for all devices in the final focus system of the SLC are listed. The formal names consist of a device type designator, microprocessor designator, and a four-digit unit number. (LEW)

  7. 10 CFR 603.890 - Final performance report.

    Science.gov (United States)

    2010-01-01

    ... to Other Administrative Matters Financial and Programmatic Reporting § 603.890 Final performance report. A TIA must require a final performance report that addresses all major accomplishments under the... 10 Energy 4 2010-01-01 2010-01-01 false Final performance report. 603.890 Section 603.890 Energy...

  8. SLC Final Performance and Lessons

    International Nuclear Information System (INIS)

    Phinney, Nan

    2000-01-01

    The Stanford Linear Collider (SLC) was the first prototype of a new type of accelerator, the electron-positron linear collider. Many years of dedicated effort were required to understand the physics of this new technology and to develop the techniques for maximizing performance. Key issues were emittance dilution, stability, final beam optimization and background control. Precision, non-invasive diagnostics were required to measure and monitor the beams throughout the machine. Beam-based feedback systems were needed to stabilize energy, trajectory, intensity and the final beam size at the interaction point. variety of new tuning techniques were developed to correct for residual optical or alignment errors. The final focus system underwent a series of refinements in order to deliver sub-micron size beams. It also took many iterations to understand the sources of backgrounds and develop the methods to control them. The benefit from this accumulated experience was seen in the performance of the SLC during its final run in 1997-98. The luminosity increased by a factor of three to 3*10 30 and the 350,000 Z data sample delivered was nearly double that from all previous runs combined

  9. A comparison of inflation expectations and inflation credibility in South Africa: results from survey data

    Directory of Open Access Journals (Sweden)

    Jannie Rossouw

    2011-08-01

    Full Text Available This paper reports a comparison of South African household inflation expectations and inflation credibility surveys undertaken in 2006 and 2008. It tests for possible feed-through between inflation credibility and inflation expectations. It supplements earlier research that focused only on the 2006 survey results. The comparison shows that inflation expectations differed between different income groups in both 2006 and 2008. Inflation credibility differed between male and female respondents, but this difference did not feed through to inflation expectations. More periodic survey data will be required for developing final conclusions on the possibility of feed-through effects. To this end the structure of credibility surveys should be reconsidered, as a large percentage of respondents indicated that they ‘don’t know’ whether the historic rate of inflation is an accurate indication of price increases.

  10. A numerical study on oceanic dispersion and sedimentation of radioactive cesium-137 from Fukushima Daiichi Nuclear Power Plant

    International Nuclear Information System (INIS)

    Higashi, Hironori; Morino, Yu; Ohara, Toshimasa

    2014-01-01

    We discussed a numerical model for oceanic dispersion and sedimentation of radioactive cesium-137 (Cs-137) in shallow water regions to clarify migration behavior of Cs-137 from Fukushima Daiichi Nuclear Power Plant. Our model considered oceanic transport by three dimensional ocean current, adsorption with large particulate matter (LPM), sedimentation and resuspension. The simulation well reproduced the spatial characteristics of sea surface concentration and sediment surface concentration of Cs-137 off Miyagi, Fukushima, and Ibaraki Prefectures during May-December 2011. The simulated results indicated that the adsorption-sedimentation of Cs-137 significantly occurred during strong wind events because the large amount of LPM was transported to upward layer by resuspension and vertical mixing. (author)

  11. Storage and remobilization of suspended sediment in the lower amazon river of Brazil

    Science.gov (United States)

    Meade, R.H.; Dunne, T.; Richey, J.E.; Santos, U.De. M.; Salati, E.

    1985-01-01

    In the lower Amazon River, suspended sediment is stored during rising stages of the river and resuspended during falling river stages. The storage and resuspension in the reach are related to the mean slope of the flood wave on the river surface; this slope is smaller during rising river stages than during falling stages. The pattern of storage and resuspension damps out the extreme values of high and low sediment discharge and tends to keep them near the mean value between 3.0 ?? 106 and 3.5 ?? 106 metric tons per day. Mean annual discharge of suspended sediment in the lower Amazon is between 1.1 ?? 109 and 1.3 ?? 109 metric tons per year.

  12. Flow-controlled magnetic particle manipulation

    Science.gov (United States)

    Grate, Jay W [West Richland, WA; Bruckner-Lea, Cynthia J [Richland, WA; Holman, David A [Las Vegas, NV

    2011-02-22

    Inventive methods and apparatus are useful for collecting magnetic materials in one or more magnetic fields and resuspending the particles into a dispersion medium, and optionally repeating collection/resuspension one or more times in the same or a different medium, by controlling the direction and rate of fluid flow through a fluid flow path. The methods provide for contacting derivatized particles with test samples and reagents, removal of excess reagent, washing of magnetic material, and resuspension for analysis, among other uses. The methods are applicable to a wide variety of chemical and biological materials that are susceptible to magnetic labeling, including, for example, cells, viruses, oligonucleotides, proteins, hormones, receptor-ligand complexes, environmental contaminants and the like.

  13. Cassini's Grand Finale Science Highlights

    Science.gov (United States)

    Spilker, Linda

    2017-10-01

    After 13 years in orbit, the Cassini-Huygens Mission to Saturn ended in a science-rich blaze of glory. Cassini returned its final bits of unique science data on September 15, 2017, as it plunged into Saturn's atmosphere satisfying planetary protection requirements. Cassini's Grand Finale covered a period of roughly five months and ended with the first time exploration of the region between the rings and planet.The final close flyby of Titan in late April 2017 propelled Cassini across Saturn’s main rings and into its Grand Finale orbits; 22 orbits that repeatedly dove between Saturn’s innermost rings and upper atmosphere making Cassini the first spacecraft to explore this region. The last orbit turned the spacecraft into the first Saturn upper atmospheric probe.The Grand Finale orbits provided highest resolution observations of both the rings and Saturn, and in-situ sampling of the ring particle composition, Saturn's atmosphere, plasma, and innermost radiation belts. The gravitational field was measured to unprecedented accuracy, providing information on the interior structure of the planet, winds in the deeper atmosphere, and mass of the rings. The magnetic field provided insight into the physical nature of the magnetic dynamo and structure of the internal magnetic field. The ion and neutral mass spectrometer sampled the upper atmosphere for molecules that escape the atmosphere in addition to molecules originating from the rings. The cosmic dust analyzer directly sampled the composition from different parts of the main rings for the first time. Fields and particles instruments directly measured the plasma environment between the rings and planet.Science highlights and new mysteries gleaned to date from the Grand Finale orbits will be discussed.The research described in this paper was carried out in part at the Jet Propulsion Laboratory, California Institute of Technology, under a contract with the National Aeronautics and Space Administration. Copyright 2017

  14. COMPARISON OF SVM AND FUZZY CLASSIFIER FOR AN INDIAN SCRIPT

    Directory of Open Access Journals (Sweden)

    M. J. Baheti

    2012-01-01

    Full Text Available With the advent of technological era, conversion of scanned document (handwritten or printed into machine editable format has attracted many researchers. This paper deals with the problem of recognition of Gujarati handwritten numerals. Gujarati numeral recognition requires performing some specific steps as a part of preprocessing. For preprocessing digitization, segmentation, normalization and thinning are done with considering that the image have almost no noise. Further affine invariant moments based model is used for feature extraction and finally Support Vector Machine (SVM and Fuzzy classifiers are used for numeral classification. . The comparison of SVM and Fuzzy classifier is made and it can be seen that SVM procured better results as compared to Fuzzy Classifier.

  15. Automatic Road Pavement Assessment with Image Processing: Review and Comparison

    Directory of Open Access Journals (Sweden)

    Sylvie Chambon

    2011-01-01

    Full Text Available In the field of noninvasive sensing techniques for civil infrastructures monitoring, this paper addresses the problem of crack detection, in the surface of the French national roads, by automatic analysis of optical images. The first contribution is a state of the art of the image-processing tools applied to civil engineering. The second contribution is about fine-defect detection in pavement surface. The approach is based on a multi-scale extraction and a Markovian segmentation. Third, an evaluation and comparison protocol which has been designed for evaluating this difficult task—the road pavement crack detection—is introduced. Finally, the proposed method is validated, analysed, and compared to a detection approach based on morphological tools.

  16. Final focus systems for linear colliders

    International Nuclear Information System (INIS)

    Helm, R.; Irwin, J.

    1992-08-01

    Final focus systems for linear colliders present many exacting challenges in beam optics, component design, and beam quality. Efforts to resolve these problems as they relate to a new generation of linear colliders are under way at several laboratories around the world. We will outline criteria for final focus systems and discuss the current state of understanding and resolution of the outstanding problems. We will discuss tolerances on alignment, field quality and stability for optical elements, and the implications for beam parameters such as emittance, energy spread, bunch length, and stability in position and energy. Beam-based correction procedures, which in principle can alleviate many of the tolerances, will be described. Preliminary results from the Final Focus Test Beam (FFTB) under construction at SLAC will be given. Finally, we mention conclusions from operating experience at the Stanford Linear Collider (SLC)

  17. Final focus systems for linear colliders

    International Nuclear Information System (INIS)

    Helm, R.; Irwing, J.

    1992-01-01

    Final focus systems for linear colliders present many exacting challenges in beam optics, component design, and beam quality. Efforts to resolve these problems as they relate to a new generation of linear colliders are under way at several laboratories around the world. We outline criteria for final focus systems and discuss the current state of understanding and resolution of the outstanding problems. We discuss tolerances on alignment, field quality and stability for optical elements, and the implications for beam parameters such as emittance, energy spread , bunch length, and stability in position and energy. Beam-based correction procedures, which in principle can alleviate many of the tolerances, are described. Preliminary results from the Final Focus Test Beam (FFTB) under construction at SLAC are given. Finally, we mention conclusions from operating experience at the Stanford Linear Collider (SLC). (Author) 16 refs., 4 tabs., 6 figs

  18. Final focus systems for linear colliders

    International Nuclear Information System (INIS)

    Erickson, R.A.

    1987-11-01

    The final focus system of a linear collider must perform two primary functions, it must focus the two opposing beams so that their transverse dimensions at the interaction point are small enough to yield acceptable luminosity, and it must steer the beams together to maintain collisions. In addition, the final focus system must transport the outgoing beams to a location where they can be recycled or safely dumped. Elementary optical considerations for linear collider final focus systems are discussed, followed by chromatic aberrations. The design of the final focus system of the SLAC Linear Collider (SLC) is described. Tuning and diagnostics and steering to collision are discussed. Most of the examples illustrating the concepts covered are drawn from the SLC, but the principles and conclusions are said to be generally applicable to other linear collider designs as well. 26 refs., 17 figs

  19. Final report on COOMET.RI(II)-S2.Eu-152 (319/RU/04): Comparison measurements of radionuclide volume sources (Eu-152)

    International Nuclear Information System (INIS)

    Korostin, S.; Hernandez, T.; Oropesa, P.; Arnold, D.; Evseev, V.; Ivanukovich, A.; Milevskiy, V.; Svec, A.; Lapenas, A.; Andonova, V.; Steiner, V.

    2010-01-01

    Measurements of the Eu-152 specific activity in artificial volume sample of water density were performed in nine laboratories with the HPGe spectrometry technique. Analysis of the gamma radiation absorption in the sample material confirmed the Compton scattering as the main mechanism of interaction of photons with energy between 300 - 600 keV and 779 - 1408 keV in the most important for environmental monitoring substances (food, water, biological materials, soils). A list of CMCs supported by the comparison is suggested. (authors)

  20. Final report on COOMET.RI(II)-S2.Eu-152 (319/RU/04): Comparison measurements of radionuclide volume sources (Eu-152)

    Energy Technology Data Exchange (ETDEWEB)

    Korostin, S. [All Russian Research Institute for Physical-Technical and Radio-Technical Measurements (VNIIFTRI), Mendeleevo (Russian Federation); Hernandez, T.; Oropesa, P. [Center of Isotopes - Radionuclide Metrology Department (CENTIS-DMR), Habana (Cuba); Arnold, D. [Physikalisch-Technische Bundesanstalt (PTB), Braunschweig (Germany); Evseev, V. [National Scientific Centre ' Institute of Metrology' (NSC IM), Kharkov (Ukraine); Ivanukovich, A.; Milevskiy, V. [Belarusian State Institute of Metrology (BelGIM), Minsk (Belarus); Svec, A. [Slovak Institute of Metrology (SMU), Bratislava (Slovakia); Lapenas, A. [Latvian National Metrology Centre Ltd, Radiation Metrology and Testing Centre (RMTC), Salaspils (Latvia); Andonova, V. [Bulgarian Institute of Metrology - National Centre of Metrology (BIM-NCM), Sofia (Bulgaria); Steiner, V. [Ministry of the Environment - Radiation and Noise Division (ISR-MoE), Jerusalem (Israel)

    2010-04-15

    Measurements of the Eu-152 specific activity in artificial volume sample of water density were performed in nine laboratories with the HPGe spectrometry technique. Analysis of the gamma radiation absorption in the sample material confirmed the Compton scattering as the main mechanism of interaction of photons with energy between 300 - 600 keV and 779 - 1408 keV in the most important for environmental monitoring substances (food, water, biological materials, soils). A list of CMCs supported by the comparison is suggested. (authors)