Time-independent and time-dependent contributions to the unavailability of standby safety system components

International Nuclear Information System (INIS)

Lofgren, E.V.; Uryasev, S.; Samanta, P.

1997-01-01

The unavailability of standby safety system components due to failures in nuclear power plants is considered to involve a time-independent and a time-dependent part. The former relates to the component's unavailability from demand stresses due to usage, and the latter represents the component's unavailability due to standby-time stresses related to the environment. In this paper, data from the nuclear plant reliability data system (NPRDS) were used to partition the component's unavailability into the contributions from standby-time stress (i.e., due to environmental factors) and demand stress (i.e., due to usage). Analyses are presented of motor-operated valves (MOVs), motor-driven pumps (MDPs), and turbine-driven pumps (TDPs). MOVs fail predominantly (approx. 78 %) from environmental factors (standby-time stress failures). MDPs fail slightly more frequently from demand stresses (approx. 63 %) than standby-time stresses, while TDPs fail predominantly from standby-time stresses (approx. 78 %). Such partitions of component unavailability have many uses in risk-informed and performance-based regulation relating to modifications to Technical Specification, in-service testing, precise determination of dominant accident sequences, and implementation of maintenance rules

Justification of response time testing requirements for pressure and differential pressure sensors

International Nuclear Information System (INIS)

Weiss, J.M.; Mayo, C.; Swisher, V.

1991-01-01

This paper reports on response time testing (RTT) requirements that were imposed on pressure, differential pressure sensors as a conservative approach to insure that assumptions in the plant safety analyses were met. The purpose of this project has been to identify the need for response time testing using the bases identified in IEEE Standard 338. A combination of plant data analyses, failure modes, and effects analyses (FMEAs) was performed. Eighteen currently qualified sensor models were utilized. The results of these analyses indicate that there are only two failure modes that affect response time, not sensor output concurrently. For these failure modes, appropriate plant actions and testing techniques were identified. Safety system RTT requirements were established by IEEE Standard 338-1975. Criteria for the Periodic Testing of Class IE Power, Protection Systems, presuming the need existed for this testing. This standard established guidelines for periodic testing to verify that loop response times of installed nuclear safety-related equipment were within the limits presumed by the design basis plant transient, accident analyses. The requirements covered all passive, active components in an instrument loop, including sensors. Individual components could be tested either in groups or separately to determine the overall loop response time

Externalizing psychopathology and gain-loss feedback in a simulated gambling task: dissociable components of brain response revealed by time-frequency analysis.

Science.gov (United States)

Bernat, Edward M; Nelson, Lindsay D; Steele, Vaughn R; Gehring, William J; Patrick, Christopher J

2011-05-01

Externalizing is a broad construct that reflects propensity toward a variety of impulse control problems, including antisocial personality disorder and substance use disorders. Two event-related potential responses known to be reduced among individuals high in externalizing proneness are the P300, which reflects postperceptual processing of a stimulus, and the error-related negativity (ERN), which indexes performance monitoring based on endogenous representations. In the current study, the authors used a simulated gambling task to examine the relation between externalizing proneness and the feedback-related negativity (FRN), a brain response that indexes performance monitoring related to exogenous cues, which is thought to be highly related to the ERN. Time-frequency (TF) analysis was used to disentangle the FRN from the accompanying P300 response to feedback cues by parsing the overall feedback-locked potential into distinctive theta (4-7 Hz) and delta (<3 Hz) TF components. Whereas delta-P300 amplitude was reduced among individuals high in externalizing proneness, theta-FRN response was unrelated to externalizing. These findings suggest that in contrast with previously reported deficits in endogenously based performance monitoring (as indexed by the ERN), individuals prone to externalizing problems show intact monitoring of exogenous cues (as indexed by the FRN). The results also contribute to a growing body of evidence indicating that the P300 is attenuated across a broad range of task conditions in high-externalizing individuals.

Multivariate Time Series Decomposition into Oscillation Components.

Science.gov (United States)

Matsuda, Takeru; Komaki, Fumiyasu

2017-08-01

Many time series are considered to be a superposition of several oscillation components. We have proposed a method for decomposing univariate time series into oscillation components and estimating their phases (Matsuda & Komaki, 2017 ). In this study, we extend that method to multivariate time series. We assume that several oscillators underlie the given multivariate time series and that each variable corresponds to a superposition of the projections of the oscillators. Thus, the oscillators superpose on each variable with amplitude and phase modulation. Based on this idea, we develop gaussian linear state-space models and use them to decompose the given multivariate time series. The model parameters are estimated from data using the empirical Bayes method, and the number of oscillators is determined using the Akaike information criterion. Therefore, the proposed method extracts underlying oscillators in a data-driven manner and enables investigation of phase dynamics in a given multivariate time series. Numerical results show the effectiveness of the proposed method. From monthly mean north-south sunspot number data, the proposed method reveals an interesting phase relationship.

Aging effects on the binaural interaction component of the auditory brainstem response in the Mongolian gerbil: Effects of interaural time and level differences.

Science.gov (United States)

Laumen, Geneviève; Tollin, Daniel J; Beutelmann, Rainer; Klump, Georg M

2016-07-01

The effect of interaural time difference (ITD) and interaural level difference (ILD) on wave 4 of the binaural and summed monaural auditory brainstem responses (ABRs) as well as on the DN1 component of the binaural interaction component (BIC) of the ABR in young and old Mongolian gerbils (Meriones unguiculatus) was investigated. Measurements were made at a fixed sound pressure level (SPL) and a fixed level above visually detected ABR threshold to compensate for individual hearing threshold differences. In both stimulation modes (fixed SPL and fixed level above visually detected ABR threshold) an effect of ITD on the latency and the amplitude of wave 4 as well as of the BIC was observed. With increasing absolute ITD values BIC latencies were increased and amplitudes were decreased. ILD had a much smaller effect on these measures. Old animals showed a reduced amplitude of the DN1 component. This difference was due to a smaller wave 4 in the summed monaural ABRs of old animals compared to young animals whereas wave 4 in the binaural-evoked ABR showed no age-related difference. In old animals the small amplitude of the DN1 component was correlated with small binaural-evoked wave 1 and wave 3 amplitudes. This suggests that the reduced peripheral input affects central binaural processing which is reflected in the BIC. Copyright © 2016 Elsevier B.V. All rights reserved.

Phonemes as short time cognitive components

DEFF Research Database (Denmark)

Feng, Ling; Hansen, Lars Kai

2006-01-01

are the smallest contrastive unit in the sound system of a language. Generalizable components were found deriving from phonemes based on homomorphic filtering features with basic time scale (20 msec). We sparsified the features based on energy as a preprocessing means to eliminate the intrinsic noise. Independent...

Aging of systems: theoretical investigations on system and components time behaviour

International Nuclear Information System (INIS)

Eid, M.; Coudray, R.

1995-01-01

Being a direct indicator of aging, the systems time-dependent failure rates need to be evaluated using qualified methodologies and starting from basic components time-dependent failure data. Basic component time-dependent failure data are not often available. Components failure data used in the paper are issued from some theoretical considerations rather than from field statistical observations. Four academic cases are presented and their results are discussed. Evaluations result in, very often, systems time-dependent failure rates that require understanding and careful interpretation. Kinetic trends of systems and of components may sometimes be different. (authors). 4 figs., 3 tabs., 3 refs., 1 appendix

Spatiotemporal Patterns of Precipitation-Modulated Landslide Deformation From Independent Component Analysis of InSAR Time Series

Science.gov (United States)

Cohen-Waeber, J.; Bürgmann, R.; Chaussard, E.; Giannico, C.; Ferretti, A.

2018-02-01

Long-term landslide deformation is disruptive and costly in urbanized environments. We rely on TerraSAR-X satellite images (2009-2014) and an improved data processing algorithm (SqueeSAR™) to produce an exceptionally dense Interferometric Synthetic Aperture Radar ground deformation time series for the San Francisco East Bay Hills. Independent and principal component analyses of the time series reveal four distinct spatial and temporal surface deformation patterns in the area around Blakemont landslide, which we relate to different geomechanical processes. Two components of time-dependent landslide deformation isolate continuous motion and motion driven by precipitation-modulated pore pressure changes controlled by annual seasonal cycles and multiyear drought conditions. Two components capturing more widespread seasonal deformation separate precipitation-modulated soil swelling from annual cycles that may be related to groundwater level changes and thermal expansion of buildings. High-resolution characterization of landslide response to precipitation is a first step toward improved hazard forecasting.

Time Domains of the Hypoxic Ventilatory Response and Their Molecular Basis

Science.gov (United States)

Pamenter, Matthew E.; Powell, Frank L.

2016-01-01

Ventilatory responses to hypoxia vary widely depending on the pattern and length of hypoxic exposure. Acute, prolonged, or intermittent hypoxic episodes can increase or decrease breathing for seconds to years, both during the hypoxic stimulus, and also after its removal. These myriad effects are the result of a complicated web of molecular interactions that underlie plasticity in the respiratory control reflex circuits and ultimately control the physiology of breathing in hypoxia. Since the time domains of the physiological hypoxic ventilatory response (HVR) were identified, considerable research effort has gone toward elucidating the underlying molecular mechanisms that mediate these varied responses. This research has begun to describe complicated and plastic interactions in the relay circuits between the peripheral chemoreceptors and the ventilatory control circuits within the central nervous system. Intriguingly, many of these molecular pathways seem to share key components between the different time domains, suggesting that varied physiological HVRs are the result of specific modifications to overlapping pathways. This review highlights what has been discovered regarding the cell and molecular level control of the time domains of the HVR, and highlights key areas where further research is required. Understanding the molecular control of ventilation in hypoxia has important implications for basic physiology and is emerging as an important component of several clinical fields. PMID:27347896

Identifying Industry-Specific Components of Product Liability Response System Using Delphi-AHP Method

Directory of Open Access Journals (Sweden)

Seo JunHyeok

2016-12-01

Full Text Available PL (product liability response system is an enterprise-wide system that prevents company’s financial loss due to PL-related accidents. Existing researches on PL response system are mainly focused on preventive and/or defense strategies for the companies. Also, it is obvious that each industry has their original characteristics related on PL issues. It means industry-specific characteristics should be considered to adopt PL response strategies. Thus, this paper aims to discuss industry-specific PL response system and their components. Based on prior researches, we tried to reveal the possibility of its application to manufacturing companies of existing PL response strategies using Delphi method with PL experts. Based on first round results, we tried to classify existing PL strategies of manufacturing companies into several categories. To validate our suggestion for essential components of PL response system, second round Delphi method are applied. Analytic hierarchy process (AHP technique will be applied to identify a prioritized list of each components and strategies. Existing PL response strategies could be categorized with six components – strategy, technology, investment, training, awareness, and organization. Among six components, Technology – it represents the technology needed for improving the safety of all products – is the most important components to prepare PL accidents. The limitation of this paper is on the size of survey and variety of examples. However, the future study will enhance the potential of the proposed method. Regardless of rich research efforts to identify PL response strategies, there is no effort to categorize these strategies and prioritized them. Well-coordinated and actionable PL response strategies and their priorities could help small-and-medium sized enterprise (SME to develop their own PL response system with their limited resources.

Response Time Analysis and Test of Protection System Instrument Channels for APR1400 and OPR1000

Energy Technology Data Exchange (ETDEWEB)

Lee, Chang Jae; Han, Seung; Yun, Jae Hee; Baek, Seung Min [Department of Instrumentation and Control System Engineering, KEPCO Engineering and Construction, Daejeon (Korea, Republic of); Lee, Sang Jeong [Department of Electronics Engineering, Chungnam National University, Daejeon (Korea, Republic of)

2015-07-01

, the establishment of the systematic response time evaluation methodology is needed to justify the conformance to the response time requirement used in the safety analysis. This paper proposes the response time evaluation methodology for APR1400 and OPR1000 using the combined analysis and test technique to confirm that the plant protection system can meet the analytical response time assumed in the safety analysis. In addition, the results of the quantitative evaluation performed for APR1400 and OPR1000 are presented in this paper. The proposed response time analysis technique consists of defining the response time requirement, determining the critical signal path for the trip parameter, allocating individual response time to each component on the signal path, and analyzing the total response time for the trip parameter, and demonstrates that the total analyzed response time does not exceed the response time requirement. The proposed response time test technique is composed of defining the response time requirement, determining the critical signal path for the trip parameter, determining the test method for each component on the signal path, performing the response time test, and demonstrates that the total test result does not exceed the response time requirement. The total response time should be tested in a single test that covers from the sensor to the final actuation device on the instrument channel. When the total channel is not tested in a single test, separate tests on groups of components or single components including the total instrument channel shall be combined to verify the total channel response. For APR1400 and OPR1000, the ramp test technique is used for the pressure and differential pressure transmitters and the step function testing technique is applied to the signal processing equipment and final actuation device. As a result, it can be demonstrated that the response time requirement is satisfied by the combined analysis and test technique

Response Time Analysis and Test of Protection System Instrument Channels for APR1400 and OPR1000

International Nuclear Information System (INIS)

Lee, Chang Jae; Han, Seung; Yun, Jae Hee; Baek, Seung Min; Lee, Sang Jeong

2015-01-01

, the establishment of the systematic response time evaluation methodology is needed to justify the conformance to the response time requirement used in the safety analysis. This paper proposes the response time evaluation methodology for APR1400 and OPR1000 using the combined analysis and test technique to confirm that the plant protection system can meet the analytical response time assumed in the safety analysis. In addition, the results of the quantitative evaluation performed for APR1400 and OPR1000 are presented in this paper. The proposed response time analysis technique consists of defining the response time requirement, determining the critical signal path for the trip parameter, allocating individual response time to each component on the signal path, and analyzing the total response time for the trip parameter, and demonstrates that the total analyzed response time does not exceed the response time requirement. The proposed response time test technique is composed of defining the response time requirement, determining the critical signal path for the trip parameter, determining the test method for each component on the signal path, performing the response time test, and demonstrates that the total test result does not exceed the response time requirement. The total response time should be tested in a single test that covers from the sensor to the final actuation device on the instrument channel. When the total channel is not tested in a single test, separate tests on groups of components or single components including the total instrument channel shall be combined to verify the total channel response. For APR1400 and OPR1000, the ramp test technique is used for the pressure and differential pressure transmitters and the step function testing technique is applied to the signal processing equipment and final actuation device. As a result, it can be demonstrated that the response time requirement is satisfied by the combined analysis and test technique

Developing Reusable and Reconfigurable Real-Time Software using Aspects and Components

OpenAIRE

Tešanović, Aleksandra

2006-01-01

Our main focus in this thesis is on providing guidelines, methods, and tools for design, configuration, and analysis of configurable and reusable real-time software, developed using a combination of aspect-oriented and component-based software development. Specifically, we define a reconfigurable real-time component model (RTCOM) that describes how a real-time component, supporting aspects and enforcing information hiding, could efficiently be designed and implemented. In this context, we out...

Performance Evaluation of Components Using a Granularity-based Interface Between Real-Time Calculus and Timed Automata

Directory of Open Access Journals (Sweden)

Karine Altisen

2010-06-01

Full Text Available To analyze complex and heterogeneous real-time embedded systems, recent works have proposed interface techniques between real-time calculus (RTC and timed automata (TA, in order to take advantage of the strengths of each technique for analyzing various components. But the time to analyze a state-based component modeled by TA may be prohibitively high, due to the state space explosion problem. In this paper, we propose a framework of granularity-based interfacing to speed up the analysis of a TA modeled component. First, we abstract fine models to work with event streams at coarse granularity. We perform analysis of the component at multiple coarse granularities and then based on RTC theory, we derive lower and upper bounds on arrival patterns of the fine output streams using the causality closure algorithm. Our framework can help to achieve tradeoffs between precision and analysis time.

Adaptive operational modal identification for slow linear time-varying structures based on frozen-in coefficient method and limited memory recursive principal component analysis

Science.gov (United States)

Wang, Cheng; Guan, Wei; Wang, J. Y.; Zhong, Bineng; Lai, Xiongming; Chen, Yewang; Xiang, Liang

2018-02-01

To adaptively identify the transient modal parameters for linear weakly damped structures with slow time-varying characteristics under unmeasured stationary random ambient loads, this paper proposes a novel operational modal analysis (OMA) method based on the frozen-in coefficient method and limited memory recursive principal component analysis (LMRPCA). In the modal coordinate, the random vibration response signals of mechanical weakly damped structures can be decomposed into the inner product of modal shapes and modal responses, from which the natural frequencies and damping ratios can be well acquired by single-degree-of-freedom (SDOF) identification approach such as FFT. Hence, for the OMA method based on principal component analysis (PCA), it becomes very crucial to examine the relation between the transformational matrix and the modal shapes matrix, to find the association between the principal components (PCs) matrix and the modal responses matrix, and to turn the operational modal parameter identification problem into PCA of the stationary random vibration response signals of weakly damped mechanical structures. Based on the theory of "time-freezing", the method of frozen-in coefficient, and the assumption of "short time invariant" and "quasistationary", the non-stationary random response signals of the weakly damped and slow linear time-varying structures (LTV) can approximately be seen as the stationary random response time series of weakly damped and linear time invariant structures (LTI) in a short interval. Thus, the adaptive identification of time-varying operational modal parameters is turned into decompositing the PCs of stationary random vibration response signals subsection of weakly damped mechanical structures after choosing an appropriate limited memory window. Finally, a three-degree-of-freedom (DOF) structure with weakly damped and slow time-varying mass is presented to illustrate this method of identification. Results show that the LMRPCA

Time-dependent density functional theory for multi-component systems

International Nuclear Information System (INIS)

Tiecheng Li; Peiqing Tong

1985-10-01

The Runge-Gross version of Hohenberg-Kohn-Sham's density functional theory is generalized to multi-component systems, both for arbitrary time-dependent pure states and for arbitrary time-dependent ensembles. (author)

Counterbalancing Regulation in Response Memory of a Positively Autoregulated Two-Component System.

Science.gov (United States)

Gao, Rong; Godfrey, Katherine A; Sufian, Mahir A; Stock, Ann M

2017-09-15

. In this study, we examined the molecular "memory" that is generated by previous exposure to stimulus. Under our experimental conditions, activating effects of autoregulated two-component signaling and inhibitory effects of the stress response counterbalanced the transcriptional output to approach response homeostasis whether or not cells had been preexposed to stimulus. Modeling allows prediction of response behavior in different scenarios and demonstrates both the robustness of the system output and its sensitivity to historical parameters such as timing and levels of exposure to stimuli. Copyright © 2017 American Society for Microbiology.

Counterbalancing Regulation in Response Memory of a Positively Autoregulated Two-Component System

Science.gov (United States)

Gao, Rong; Godfrey, Katherine A.; Sufian, Mahir A.

2017-01-01

with such complexity. In this study, we examined the molecular “memory” that is generated by previous exposure to stimulus. Under our experimental conditions, activating effects of autoregulated two-component signaling and inhibitory effects of the stress response counterbalanced the transcriptional output to approach response homeostasis whether or not cells had been preexposed to stimulus. Modeling allows prediction of response behavior in different scenarios and demonstrates both the robustness of the system output and its sensitivity to historical parameters such as timing and levels of exposure to stimuli. PMID:28674072

Lateralization and Binaural Interaction of Middle-Latency and Late-Brainstem Components of the Auditory Evoked Response.

Science.gov (United States)

Dykstra, Andrew R; Burchard, Daniel; Starzynski, Christian; Riedel, Helmut; Rupp, Andre; Gutschalk, Alexander

2016-08-01

We used magnetoencephalography to examine lateralization and binaural interaction of the middle-latency and late-brainstem components of the auditory evoked response (the MLR and SN10, respectively). Click stimuli were presented either monaurally, or binaurally with left- or right-leading interaural time differences (ITDs). While early MLR components, including the N19 and P30, were larger for monaural stimuli presented contralaterally (by approximately 30 and 36 % in the left and right hemispheres, respectively), later components, including the N40 and P50, were larger ipsilaterally. In contrast, MLRs elicited by binaural clicks with left- or right-leading ITDs did not differ. Depending on filter settings, weak binaural interaction could be observed as early as the P13 but was clearly much larger for later components, beginning at the P30, indicating some degree of binaural linearity up to early stages of cortical processing. The SN10, an obscure late-brainstem component, was observed consistently in individuals and showed linear binaural additivity. The results indicate that while the MLR is lateralized in response to monaural stimuli-and not ITDs-this lateralization reverses from primarily contralateral to primarily ipsilateral as early as 40 ms post stimulus and is never as large as that seen with fMRI.

Blind Separation of Event-Related Brain Responses into Independent Components

National Research Council Canada - National Science Library

Makeig, Scott

1996-01-01

.... We report here a method for the blind separation of event-related brain responses into spatially stationary and temporally independent subcomponents using an Independent Component Analysis algorithm...

Electroantennographic responses of New World screwworm to components of swormlure-4 and related compounds

International Nuclear Information System (INIS)

Cork, A.

1992-01-01

Electroantennographic (EAG) responses from New World screwworm flies were recorded as dose-response curves to the components of swormlure and to isobutyric acid, butanol, 1-hexanol, 1-octen-3-o1, 3-propylphenol and 3-methylindole. Among the swormlure components, good responses were obtained to valeric acid, phenol 4-methylphenol and indole. Only weaker responses were obtained to the butyl alcohols, dimethyldisulphide, acetic, butyric and benzoic acids. A strong response was obtained to 1-octen-3-o1, and the response to 3-methylindole was greater than that to indole. Responses of male and female flies were generally similar, except for those to dimethylsulphide and 4-methylphenol where responses fo males were greater than those of females. These studies indicate that EAG linked to gas chromatography should be a useful technique for detection of the biologically-active components in naturally-derived, volatile attractants, and suggest 1-octen-3-o1 and 3- methylindole should be tested for behavioural effects on NWS. 7 figs

Comparison of Component Frameworks for Real-Time Embedded Systems

Czech Academy of Sciences Publication Activity Database

Pop, T.; Hnětynka, P.; Hošek, P.; Malohlava, M.; Bureš, Tomáš

2014-01-01

Roč. 40, č. 1 (2014), s. 127-170 ISSN 0219-1377 Grant - others:GA AV ČR(CZ) GAP202/11/0312; GA UK(CZ) Project 378111; UK(CZ) SVV-2013- 267312 Keywords : component-based development * component frameworks * real-time and embedded systems Subject RIV: JC - Computer Hardware ; Software Impact factor: 1.782, year: 2014

Generation of synthetic time histories compatible with multiple-damping design response spectra

International Nuclear Information System (INIS)

Lilhanand, K.; Tseng, W.S.

1987-01-01

Seismic design of nuclear power plants as currently practiced requires time history analyses be performed to generate floor response spectra for seismic qualification of piping, equipment, and components. Since design response spectra are normally prescribed in the form of smooth spectra, the generation of synthetic time histories whose response spectra closely match the ''target'' design spectra of multiple damping values, is often required for the seismic time history analysis purpose. Various methods of generation of synthetic time histories compatible with target response spectra have been proposed in the literature. Since the mathematical problem of determining a time history from a given set of response spectral values is not unique, an exact solution is not possible, and all the proposed methods resort to some forms of approximate solutions. In this paper, a new iteration scheme, is described which effectively removes the difficulties encountered by the existing methods. This new iteration scheme can not only improve the accuracy of spectrum matching for a single-damping target spectrum, but also automate the spectrum matching for multiple-damping target spectra. The applicability and limitations as well as the method adopted to improve the numerical stability of this new iteration scheme are presented. The effectiveness of this new iteration scheme is illustrated by two example applications

Identification of chemical components of combustion emissions that affect pro-atherosclerotic vascular responses in mice.

Science.gov (United States)

Seilkop, Steven K; Campen, Matthew J; Lund, Amie K; McDonald, Jacob D; Mauderly, Joe L

2012-04-01

Combustion emissions cause pro-atherosclerotic responses in apolipoprotein E-deficient (ApoE/⁻) mice, but the causal components of these complex mixtures are unresolved. In studies previously reported, ApoE⁻/⁻ mice were exposed by inhalation 6 h/day for 50 consecutive days to multiple dilutions of diesel or gasoline exhaust, wood smoke, or simulated "downwind" coal emissions. In this study, the analysis of the combined four-study database using the Multiple Additive Regression Trees (MART) data mining approach to determine putative causal exposure components regardless of combustion source is reported. Over 700 physical-chemical components were grouped into 45 predictor variables. Response variables measured in aorta included endothelin-1, vascular endothelin growth factor, three matrix metalloproteinases (3, 7, 9), metalloproteinase inhibitor 2, heme-oxygenase-1, and thiobarbituric acid reactive substances. Two or three predictors typically explained most of the variation in response among the experimental groups. Overall, sulfur dioxide, ammonia, nitrogen oxides, and carbon monoxide were most highly predictive of responses, although their rankings differed among the responses. Consistent with the earlier finding that filtration of particles had little effect on responses, particulate components ranked third to seventh in predictive importance for the eight response variables. MART proved useful for identifying putative causal components, although the small number of pollution mixtures (4) can provide only suggestive evidence of causality. The potential independent causal contributions of these gases to the vascular responses, as well as possible interactions among them and other components of complex pollutant mixtures, warrant further evaluation.

Test-Anchored Vibration Response Predictions for an Acoustically Energized Curved Orthogrid Panel with Mounted Components

Science.gov (United States)

Frady, Gregory P.; Duvall, Lowery D.; Fulcher, Clay W. G.; Laverde, Bruce T.; Hunt, Ronald A.

2011-01-01

rich body of vibroacoustic test data was recently generated at Marshall Space Flight Center for component-loaded curved orthogrid panels typical of launch vehicle skin structures. The test data were used to anchor computational predictions of a variety of spatially distributed responses including acceleration, strain and component interface force. Transfer functions relating the responses to the input pressure field were generated from finite element based modal solutions and test-derived damping estimates. A diffuse acoustic field model was applied to correlate the measured input sound pressures across the energized panel. This application quantifies the ability to quickly and accurately predict a variety of responses to acoustically energized skin panels with mounted components. Favorable comparisons between the measured and predicted responses were established. The validated models were used to examine vibration response sensitivities to relevant modeling parameters such as pressure patch density, mesh density, weight of the mounted component and model form. Convergence metrics include spectral densities and cumulative root-mean squared (RMS) functions for acceleration, velocity, displacement, strain and interface force. Minimum frequencies for response convergence were established as well as recommendations for modeling techniques, particularly in the early stages of a component design when accurate structural vibration requirements are needed relatively quickly. The results were compared with long-established guidelines for modeling accuracy of component-loaded panels. A theoretical basis for the Response/Pressure Transfer Function (RPTF) approach provides insight into trends observed in the response predictions and confirmed in the test data. The software developed for the RPTF method allows easy replacement of the diffuse acoustic field with other pressure fields such as a turbulent boundary layer (TBL) model suitable for vehicle ascent. Structural responses

Simulating the Impact Response of Composite Airframe Components

Science.gov (United States)

Jackson, Karen E.; Littell, Justin D.; Fasanella, Edwin L.

2014-01-01

In 2010, NASA Langley Research Center obtained residual hardware from the US Army's Survivable Affordable Repairable Airframe Program (SARAP). The hardware consisted of a composite fuselage section that was representative of the center section of a Black Hawk helicopter. The section was fabricated by Sikorsky Aircraft Corporation and designated the Test Validation Article (TVA). The TVA was subjected to a vertical drop test in 2008 to evaluate a tilting roof concept to limit the intrusion of overhead mass items, such as the rotor transmission, into the fuselage cabin. As a result of the 2008 test, damage to the hardware was limited primarily to the roof. Consequently, when the post-test article was obtained in 2010, the roof area was removed and the remaining structure was cut into six different types of test specimens including: (1) tension and compression coupons for material property characterization, (2) I-beam sections, (3) T-sections, (4) cruciform sections, (5) a large subfloor section, and (6) a forward framed fuselage section. In 2011, NASA and Sikorsky entered into a cooperative research agreement to study the impact responses of composite airframe structures and to evaluate the capabilities of the explicit transient dynamic finite element code, LS-DYNA®, to simulate these responses including damage initiation and progressive failure. Finite element models of the composite specimens were developed and impact simulations were performed. The properties of the composite material were represented using both a progressive in-plane damage model (Mat 54) and a continuum damage mechanics model (Mat 58) in LS-DYNA. This paper provides test-analysis comparisons of time history responses and the location and type of damage for representative I-beam, T-section, and cruciform section components.

Life-time management for mechanical components; Lebensdauermanagement mechanischer Komponenten

Energy Technology Data Exchange (ETDEWEB)

Roos, E. [Stuttgart Univ. (DE). Materialpruefungsanstalt (MPA)

2006-07-01

The safety and economic efficiency of industrial systems depend on the quality of components and systems. In the field of power generation, power plants should be safe and have high availability and minimum specific generation cost. Life management is essential for this. Depending on the safety relevance of systems, structures and components (SSC), this includes proofs of integrity, time-oriented or condition-oriented preventive maintenance, or just failure-oriented maintenance. (orig.)

Hidden Markov Item Response Theory Models for Responses and Response Times.

Science.gov (United States)

Molenaar, Dylan; Oberski, Daniel; Vermunt, Jeroen; De Boeck, Paul

2016-01-01

Current approaches to model responses and response times to psychometric tests solely focus on between-subject differences in speed and ability. Within subjects, speed and ability are assumed to be constants. Violations of this assumption are generally absorbed in the residual of the model. As a result, within-subject departures from the between-subject speed and ability level remain undetected. These departures may be of interest to the researcher as they reflect differences in the response processes adopted on the items of a test. In this article, we propose a dynamic approach for responses and response times based on hidden Markov modeling to account for within-subject differences in responses and response times. A simulation study is conducted to demonstrate acceptable parameter recovery and acceptable performance of various fit indices in distinguishing between different models. In addition, both a confirmatory and an exploratory application are presented to demonstrate the practical value of the modeling approach.

Real Time Engineering Analysis Based on a Generative Component Implementation

DEFF Research Database (Denmark)

Kirkegaard, Poul Henning; Klitgaard, Jens

2007-01-01

The present paper outlines the idea of a conceptual design tool with real time engineering analysis which can be used in the early conceptual design phase. The tool is based on a parametric approach using Generative Components with embedded structural analysis. Each of these components uses the g...

Response moderation models for conditional dependence between response time and response accuracy.

Science.gov (United States)

Bolsinova, Maria; Tijmstra, Jesper; Molenaar, Dylan

2017-05-01

It is becoming more feasible and common to register response times in the application of psychometric tests. Researchers thus have the opportunity to jointly model response accuracy and response time, which provides users with more relevant information. The most common choice is to use the hierarchical model (van der Linden, 2007, Psychometrika, 72, 287), which assumes conditional independence between response time and accuracy, given a person's speed and ability. However, this assumption may be violated in practice if, for example, persons vary their speed or differ in their response strategies, leading to conditional dependence between response time and accuracy and confounding measurement. We propose six nested hierarchical models for response time and accuracy that allow for conditional dependence, and discuss their relationship to existing models. Unlike existing approaches, the proposed hierarchical models allow for various forms of conditional dependence in the model and allow the effect of continuous residual response time on response accuracy to be item-specific, person-specific, or both. Estimation procedures for the models are proposed, as well as two information criteria that can be used for model selection. Parameter recovery and usefulness of the information criteria are investigated using simulation, indicating that the procedure works well and is likely to select the appropriate model. Two empirical applications are discussed to illustrate the different types of conditional dependence that may occur in practice and how these can be captured using the proposed hierarchical models. © 2016 The British Psychological Society.

Hybrid time/frequency domain modeling of nonlinear components

DEFF Research Database (Denmark)

Wiechowski, Wojciech Tomasz; Lykkegaard, Jan; Bak, Claus Leth

2007-01-01

This paper presents a novel, three-phase hybrid time/frequency methodology for modelling of nonlinear components. The algorithm has been implemented in the DIgSILENT PowerFactory software using the DIgSILENT Programming Language (DPL), as a part of the work described in [1]. Modified HVDC benchmark...

Central and peripheral components of short latency vestibular responses in the chicken

Science.gov (United States)

Nazareth, A. M.; Jones, T. A.

1998-01-01

Far-field recordings of short latency vestibular responses to pulsed cranial translation are composed of a series of positive and negative peaks occurring within 10 ms following stimulus onset. In the bird, these vestibular evoked potentials (VsEPs) can be recorded noninvasively and have been shown in the chicken and quail to depend strictly upon the activation of the vestibular component of the eighth nerve. The utility of the VsEP in the study of vestibular systems is dependent upon a clear understanding of the neural sources of response components. The primary aim of the current research in the chicken was to critically test the hypotheses that 1) responses are generated by both peripheral and central neurons and 2) peaks P1 and N1 originate from first order vestibular neurons, whereas later waves primarily depend on activity in higher order neurons. The principal strategy used here was to surgically isolate the eighth nerve as it enters the brainstem. Interruption of primary afferents of the eighth nerve in the brainstem substantially reduced or eliminated peaks beyond P2, whereas P1 and N1 were generally spared. Surgical sections that spared vestibular pathways had little effect on responses. The degree of change in response components beyond N1 was correlated with the extent of damage to central vestibular relays. These findings support the conclusion that responses are produced by both peripheral and central elements of the vestibular system. Further, response peaks later than N1 appear to be dependent upon central relays, whereas P1 and N1 reflect activity of the peripheral nerve. These findings clarify the roles of peripheral and central neurons in the generation of vestibular evoked potentials and provide the basis for a more useful and detailed interpretation of data from vestibular response testing.

Relative response of TL and component-resolved OSL to alpha and beta radiations in annealed sedimentary quartz

International Nuclear Information System (INIS)

Polymeris, George S.; Afouxenidis, Dimitrios; Raptis, Spyridoula; Liritzis, Ioannis; Tsirliganis, Nestor C.; Kitis, George

2011-01-01

Knowledge of the relative luminescence response to alpha and beta radiation is very important in TL and OSL dating. In the present study the relative alpha to beta response is studied in a sedimentary quartz sample, previously fired at 900 deg. C for 1 h, in the dose region between 1 and 128 Gy, for both thermoluminescence (TL) and linearly modulated optically stimulated luminescence (LM - OSL). The LM - OSL measurements were performed at room temperature and at 125 deg. C. All OSL signals were deconvolved into their individual components. Comparison of OSL curves after alpha and beta irradiation strongly supports that quartz OSL components follow first order kinetics in both cases. In the case of TL, the relative alpha to beta response is found to be very different for each TL glow-peak, but it does not depend strongly on irradiation dose. In the case of LM - OSL measurements, it is found that the relative behaviour of the alpha to beta response is different for three distinct regions, namely the fast OSL component, the region of medium OSL component originating from the TL glow-peak at 110 deg. C when stimulation takes place at room temperature and finally the region of slow OSL component. Following stimulation at ambient temperature, the relative alpha to beta response of all components was not observed to depend significantly on dose, with the value of ratio being 0.03 and a tendency to decrease with increasing dose. However, in the case of measurements performed at 125 deg. C, the relative response of the fast components is much enhanced, and for the remaining components it increases with increasing dose. Special care must be taken to examine the relative alpha to beta response of the fast component at 125 deg. C which contrasts the relative response of the TL peak at ca. 325 deg. C. The implications for the dating of annealed quartz are also briefly discussed. - Highlights: → Relative alpha to beta response for TL and LM-OSL is studied in annealed

Response Time Test for The Application of the Data Communication Network to Nuclear Power Plant

International Nuclear Information System (INIS)

Shin, Y.C.; Lee, J.Y.; Park, H.Y.; Seong, S.H.; Chung, H.Y.

2002-01-01

This paper discusses the response time test for the application of the Data Communication Network (DCN) to Nuclear Power Plant (NPP). Conventional Instrumentation and Control (I and C) Systems using the analog technology in NPP have raised many problems regarding the lack of spare parts, maintenance burden, inaccuracy, etc.. In order to solve the problems, the Korean Next Generation Reactor (KNGR) I and C system has adopted the digital technology and new design features of using the data communication networks. It is essential to prove the response time requirements that arise from the introduction of digital I and C technology and data communication networks to nuclear power plant design. For the response time test, a high reliable data communication network structure has been developed to meet the requirements of redundancy, diversity, and segmentation. This paper presents the results of network load analysis and response time test for the KNGR DCN prototype. The test has been focused on the response time from the field components to the gateway because the response times from the gateway to the specific systems are similar to those of the existing design. It is verified that the response time requirements are met through the prototype test for KNGR I and C systems. (authors)

Determination operation Time Risk of Box Spinning Components-oe Spinning Machine

OpenAIRE

Slobodan Stefanovic

2013-01-01

Based on the constructed dependency diagram reliability of the exploitation operation time of each constituent components of the analyzed frame in the case of selected statistical distributions, areas of the operation exploitation and repair intervals are determined. This is done by determining the first inflection points. Based on these points analysis to determine the time of safety operation of frame components with allowable risk to the segmental linear function of the intensity of failur...

Thermal memory influence on the thermoconducting component of indirect photoacoustic response

International Nuclear Information System (INIS)

Nešić, M; Popović, M; Gusavac, P; Šoškić, Z; Galović, S

2012-01-01

In this paper, a model of the thermoconducting component of the indirect photoacoustic (PA) response is derived that includes thermal memory properties of the examined material and its fluid environment. A comparison is made between the derived model and the classic one, which neglects the influence of thermal memory. It has been shown that, at modulation frequencies lower than a certain boundary frequency of the light source, these models tend to overlap, while at higher frequencies, noticeable differences occur. The boundary frequency depends on heat propagation velocity through the sample and its thickness. This observation limits the validity domain of previous models to a range lower than the boundary frequency, offering, at the same time, the possibility of obtaining thermal memory properties using PA effects at frequencies above it.

Combined effects of alcohol and caffeine on the late components of the event-related potential and on reaction time.

Science.gov (United States)

Martin, Frances Heritage; Garfield, Joshua

2006-01-01

The effects of .7 ml/kg alcohol and 200 mg caffeine on the P200, N200, P300 and N500 difference wave components of the event-related potential and on reaction time (RT) were examined in 16 females who performed both simple and choice RT tasks. Alcohol slowed the decision time (DT) component of reaction time, lengthened the latency of the P200 and P300 components, reduced N200 amplitude, increased P300 amplitude at parietal sites, and modified the effect of sagittal site on N500 difference wave peak amplitude. Caffeine shortened DT in the choice RT task, shortened N200 latency at right hemisphere sites, and shortened N200 latency in the choice RT task in combination with alcohol compared to when alcohol was administered alone. Caffeine also increased P300 amplitude in the choice RT task and reduced the integral of the N500 difference wave at most sites when combined with alcohol. It was concluded that whereas alcohol slows attention allocation and impairs working memory, caffeine accelerated response-related decisions and enhanced cortical arousal.

Responses of physiological and biochemical components in Gossypium hirsutum L. to mutagens

International Nuclear Information System (INIS)

Muthusamy, A.; Vasanth, K.; Jayabalan, N.

2003-01-01

The two tetraploid varieties of cotton were exposed to gamma rays, EMS and SA. Chlorophyll, carotenoids, sugar, starch, free amino acids, protein, lipids, DNA and RNA were estimated quantitatively. All the physiological and biochemical components were increased in lower dose/concentration of the mutagenic treatments and they were decreased in higher dose/concentrations. The stimulation of the biochemical contents was a dose/concentration dependent response. Among the two varieties, MCU 11 was found to be responsive to mutagens than MCU 5. Based on the study the lower dose/concentration of the mutagenic treatments could enhance the biochemical components which is used for improved economic characters of cotton. (author)

Variance components and selection response for feather-pecking behavior in laying hens.

Science.gov (United States)

Su, G; Kjaer, J B; Sørensen, P

2005-01-01

Variance components and selection response for feather pecking behavior were studied by analyzing the data from a divergent selection experiment. An investigation indicated that a Box-Cox transformation with power lambda = -0.2 made the data approximately normally distributed and gave the best fit for the model. Variance components and selection response were estimated using Bayesian analysis with Gibbs sampling technique. The total variation was rather large for the investigated traits in both the low feather-pecking line (LP) and the high feather-pecking line (HP). Based on the mean of marginal posterior distribution, in the Box-Cox transformed scale, heritability for number of feather pecking bouts (FP bouts) was 0.174 in line LP and 0.139 in line HP. For number of feather-pecking pecks (FP pecks), heritability was 0.139 in line LP and 0.105 in line HP. No full-sib group effect and observation pen effect were found in the 2 traits. After 4 generations of selection, the total response for number of FP bouts in the transformed scale was 58 and 74% of the mean of the first generation in line LP and line HP, respectively. The total response for number of FP pecks was 47 and 46% of the mean of the first generation in line LP and line HP, respectively. The variance components and the realized selection response together suggest that genetic selection can be effective in minimizing FP behavior. This would be expected to reduce one of the major welfare problems in laying hens.

Equivalence between short-time biphasic and incompressible elastic material responses.

Science.gov (United States)

Ateshian, Gerard A; Ellis, Benjamin J; Weiss, Jeffrey A

2007-06-01

Porous-permeable tissues have often been modeled using porous media theories such as the biphasic theory. This study examines the equivalence of the short-time biphasic and incompressible elastic responses for arbitrary deformations and constitutive relations from first principles. This equivalence is illustrated in problems of unconfined compression of a disk, and of articular contact under finite deformation, using two different constitutive relations for the solid matrix of cartilage, one of which accounts for the large disparity observed between the tensile and compressive moduli in this tissue. Demonstrating this equivalence under general conditions provides a rationale for using available finite element codes for incompressible elastic materials as a practical substitute for biphasic analyses, so long as only the short-time biphasic response is sought. In practice, an incompressible elastic analysis is representative of a biphasic analysis over the short-term response deltatelasticity tensor, and K is the hydraulic permeability tensor of the solid matrix. Certain notes of caution are provided with regard to implementation issues, particularly when finite element formulations of incompressible elasticity employ an uncoupled strain energy function consisting of additive deviatoric and volumetric components.

Time-correlated single-photon counting study of multiple photoluminescence lifetime components of silicon nanoclusters

Energy Technology Data Exchange (ETDEWEB)

Diamare, D., E-mail: d.diamare@ee.ucl.ac.uk [Department of Electronic and Electrical Engineering, University College London, Torrington Place, London, WC1E 7JE (United Kingdom); Wojdak, M. [Department of Electronic and Electrical Engineering, University College London, Torrington Place, London, WC1E 7JE (United Kingdom); Lettieri, S. [Institute for Superconductors and Innovative Materials, National Council of Research (CNR-SPIN), Via Cintia 80126, Naples (Italy); Department of Physical Sciences, University of Naples “Federico II”, Via Cintia 80126, Naples (Italy); Kenyon, A.J. [Department of Electronic and Electrical Engineering, University College London, Torrington Place, London, WC1E 7JE (United Kingdom)

2013-04-15

We report time-resolved photoluminescence measurements of thin films of silica containing silicon nanoclusters (Si NCs), produced by PECVD and annealed at temperatures between 700 °C and 1150 °C. While the near infrared emission of Si NCs has long been studied, visible light emission has only recently attracted interest due to its very short decay times and its recently-reported redshift with decreasing NCs size. We analyse the PL decay dynamics in the range 450–700 nm with picosecond time resolution using Time Correlated Single Photon Counting. In the resultant multi-exponential decays two dominant components can clearly be distinguished: a very short component, in the range of hundreds of picoseconds, and a nanosecond component. In this wavelength range we do not detect the microsecond component generally associated with excitonic recombination. We associate the nanosecond component to defect relaxation: it decreases in intensity in the sample annealed at higher temperature, suggesting that the contribution from defects decreases with increasing temperature. The origin of the very fast PL component (ps time region) is also discussed. We show that it is consistent with the Auger recombination times of multiple excitons. Further work needs to be done in order to assess the contribution of the Auger-controlled recombinations to the defect-assisted mechanism of photoluminescence. -- Highlights: ► We report time-resolved PL measurements of Si-Ncs embedded in SiO{sub 2} matrix. ► Net decrease of PL with increasing the annealing temperature has been observed. ► Lifetime distribution analysis revealed a multiexponential decay with ns and ps components. ► Ps components are consistent with the lifetime range of the Auger recombination times. ► No evidence for a fast direct transition at the Brillouin zone centre.

Analysis of Femtosecond Timing Noise and Stability in Microwave Components

International Nuclear Information System (INIS)

2011-01-01

To probe chemical dynamics, X-ray pump-probe experiments trigger a change in a sample with an optical laser pulse, followed by an X-ray probe. At the Linac Coherent Light Source, LCLS, timing differences between the optical pulse and x-ray probe have been observed with an accuracy as low as 50 femtoseconds. This sets a lower bound on the number of frames one can arrange over a time scale to recreate a 'movie' of the chemical reaction. The timing system is based on phase measurements from signals corresponding to the two laser pulses; these measurements are done by using a double-balanced mixer for detection. To increase the accuracy of the system, this paper studies parameters affecting phase detection systems based on mixers, such as signal input power, noise levels, temperature drift, and the effect these parameters have on components such as the mixers, splitters, amplifiers, and phase shifters. Noise data taken with a spectrum analyzer show that splitters based on ferrite cores perform with less noise than strip-line splitters. The data also shows that noise in specific mixers does not correspond with the changes in sensitivity per input power level. Temperature drift is seen to exist on a scale between 1 and 27 fs/ o C for all of the components tested. Results show that any components using more metallic conductor tend to exhibit more noise as well as more temperature drift. The scale of these effects is large enough that specific care should be given when choosing components and designing the housing of high precision microwave mixing systems for use in detection systems such as the LCLS. With these improvements, the timing accuracy can be improved to lower than currently possible.

Interactions between photodegradation components

Directory of Open Access Journals (Sweden)

Abdollahi Yadollah

2012-09-01

Full Text Available Abstract Background The interactions of p-cresol photocatalytic degradation components were studied by response surface methodology. The study was designed by central composite design using the irradiation time, pH, the amount of photocatalyst and the p-cresol concentration as variables. The design was performed to obtain photodegradation % as actual responses. The actual responses were fitted with linear, two factor interactions, cubic and quadratic model to select an appropriate model. The selected model was validated by analysis of variance which provided evidences such as high F-value (845.09, very low P-value (2 = 0.999, adjusted R-squared (Radj2 = 0.998, predicted R-squared (Rpred2 = 0.994 and the adequate precision (95.94. Results From the validated model demonstrated that the component had interaction with irradiation time under 180 min of the time while the interaction with pH was above pH 9. Moreover, photocatalyst and p-cresol had interaction at minimal amount of photocatalyst (p-cresol. Conclusion These variables are interdependent and should be simultaneously considered during the photodegradation process, which is one of the advantages of the response surface methodology over the traditional laboratory method.

Regulatory Guide 1.122: Development of floor design response spectra for seismic design of floor-supported equipment or components

International Nuclear Information System (INIS)

Anon.

1993-01-01

''Reactor Site Criteria,'' requires, in part, that safety-related structures, systems, and components remain functional in the event of a Safe Shutdown Earthquake (SSE). It specifies the use of a suitable dynamic analysis as one method of ensuring that the structures, systems, and components can withstand the seismic loads. Similarly, paragraph (a)(2) of Section VI of the same appendix requires, in part, that the structures, systems, and components necessary for continued operation without undue risk to the health and safety of the public remain functional in the event of an Operating Basis Earthquake (OBE). Again, the use of suitable dynamic analysis is specified as one method of ensuring that the structures, systems, and components can withstand the seismic loads. This guide describes methods acceptable to the NRC staff for developing two horizontal and one vertical floor design response spectra at various floors or other equipment-support locations of interest from the time-history motions resulting from the dynamic analysis of the supporting structure. These floor design response spectra are needed for the dynamic analysis of the systems or equipment supported at various locations of the supporting structure

Response Mixture Modeling: Accounting for Heterogeneity in Item Characteristics across Response Times.

Science.gov (United States)

Molenaar, Dylan; de Boeck, Paul

2018-06-01

In item response theory modeling of responses and response times, it is commonly assumed that the item responses have the same characteristics across the response times. However, heterogeneity might arise in the data if subjects resort to different response processes when solving the test items. These differences may be within-subject effects, that is, a subject might use a certain process on some of the items and a different process with different item characteristics on the other items. If the probability of using one process over the other process depends on the subject's response time, within-subject heterogeneity of the item characteristics across the response times arises. In this paper, the method of response mixture modeling is presented to account for such heterogeneity. Contrary to traditional mixture modeling where the full response vectors are classified, response mixture modeling involves classification of the individual elements in the response vector. In a simulation study, the response mixture model is shown to be viable in terms of parameter recovery. In addition, the response mixture model is applied to a real dataset to illustrate its use in investigating within-subject heterogeneity in the item characteristics across response times.

Effect of hip braces on brake response time: Repeated measures designed study.

Science.gov (United States)

Dammerer, Dietmar; Waidmann, Cornelia; Huber, Dennis G; Krismer, Martin; Haid, Christian; Liebensteiner, Michael C

2017-08-01

The question whether or not a patient with a hip brace should drive a car is of obvious importance because the advice given to patients to resume driving is often anecdotal as few scientific data are available on this specific subject. To assess driving ability (brake response time) with commonly used hip braces. Repeated measures design. Brake response time was assessed under six conditions: (1) without a brace (control), (2) with a typical postoperative hip brace with adjustable range of motion and the settings: unrestricted, (3) flexion limited to 70°, (4) extension blocked at 20° hip flexion, (5) both flexion and extension limited (20°/70°) and (6) an elastic hip bandage. Brake response time was assessed using a custom-made driving simulator as used in previous studies. The participants were a convenience sample of able-bodied participants. A total of 70 participants (35 women and 35 men) participated in our study. Mean age was 31.1 (standard deviation: 10.6; range: 21.7-66.4) years. A significant within-subject effect for brake response time was found ( p = 0.009), but subsequent post hoc analyses revealed no significant differences between control and the other settings. Based on our findings, it does not seem mandatory to recommend driving abstinence for patients wearing a hip orthosis. We suggest that our results be interpreted with caution, because (1) an underlying pathological hip condition needs to be considered, (2) the ability to drive a car safely is multifactorial and brake response time is only one component thereof and (3) brake response time measurements were performed only with healthy participants. Clinical relevance Hip braces are used in the context of joint-preserving and prosthetic surgery of the hip. Therefore, clinicians are confronted with the question whether to allow driving a car with the respective hip brace or not. Our data suggest that hip braces do not impair brake response time.

The effect of loading time on flexible pavement dynamic response: a finite element analysis

Science.gov (United States)

Yin, Hao; Solaimanian, Mansour; Kumar, Tanmay; Stoffels, Shelley

2007-12-01

Dynamic response of asphalt concrete (AC) pavements under moving load is a key component for accurate prediction of flexible pavement performance. The time and temperature dependency of AC materials calls for utilizing advanced material characterization and mechanistic theories, such as viscoelasticity and stress/strain analysis. In layered elastic analysis, as implemented in the new Mechanistic-Empirical Pavement Design Guide (MEPDG), the time dependency is accounted for by calculating the loading times at different AC layer depths. In this study, the time effect on pavement response was evaluated by means of the concept of “pseudo temperature.” With the pavement temperature measured from instrumented thermocouples, the time and temperature dependency of AC materials was integrated into one single factor, termed “effective temperature.” Via this effective temperature, pavement responses under a transient load were predicted through finite element analysis. In the finite element model, viscoelastic behavior of AC materials was characterized through relaxation moduli, while the layers with unbound granular material were assumed to be in an elastic mode. The analysis was conducted for two different AC mixtures in a simplified flexible pavement structure at two different seasons. Finite element analysis results reveal that the loading time has a more pronounced impact on pavement response in the summer for both asphalt types. The results indicate that for reasonable prediction of dynamic response in flexible pavements, the effect of the depth-dependent loading time on pavement temperature should be considered.

Insights from random vibration analyses using multiple earthquake components

International Nuclear Information System (INIS)

DebChaudhury, A.; Gasparini, D.A.

1981-01-01

The behavior of multi-degree-of-freedom systems subjected to multiple earthquake components is studied by the use of random vibration dynamic analyses. A linear system which has been decoupled into modes and has both translational and rotational degrees of freedom is analyzed. The seismic excitation is modelled as a correlated or uncorrelated, vector-valued, non-stationary random process having a Kanai-Tajimi type of frequency content. Non-stationarity is achieved by using a piece wise linear strength function. Therefore, almost any type of evolution and decay of an earthquake may be modelled. Also, in general, the components of the excitation have different frequency contents and strength functions; i.e. intensities and durations and the correlations between components can vary with time. A state-space, modal, random vibration approach is used. Exact analytical expressions for both the state transition matrix and the evolutionary modal covariance matrix are utilized to compute time histories of modal RMS responses. Desired responses are then computed by modal superposition. Specifically, relative displacement, relative velocity and absolute acceleration responses are studied. An important advantage of such analyses is that RMS responses vary smoothly in time therefore large time intervals may be used to generate response time histories. The modal superposition is exact; that is, all cross correlation terms between modal responses are included. (orig./RW)

Understanding recovery: changes in the relationships of the International Classification of Functioning (ICF) components over time.

Science.gov (United States)

Davis, A M; Perruccio, A V; Ibrahim, S; Hogg-Johnson, S; Wong, R; Badley, E M

2012-12-01

The International Classification of Functioning, Disability and Health framework describes human functioning through body structure and function, activity and participation in the context of a person's social and physical environment. This work tested the temporal relationships of these components. Our hypotheses were: 1) there would be associations among physical impairment, activity limitations and participation restrictions within time; 2) prior status of a component would be associated with future status; 3) prior status of one component would influence status of a second component (e.g. prior activity limitations would be associated with current participation restrictions); and, 4) the magnitude of the within time relationships of the components would vary over time. Participants from Canada with primary hip or knee joint replacement (n = 931), an intervention with predictable improvement in pain and disability, completed standardized outcome measures pre-surgery and five times in the first year post-surgery. These included physical impairment (pain), activity limitations and participation restrictions. ICF component relationships were evaluated cross-sectionally and longitudinally using path analysis adjusting for age, sex, BMI, hip vs. knee, low back pain and mood. All component scores improved significantly over time. The path coefficients supported the hypotheses in that both within and across time, physical impairment was associated with activity limitation and activity limitation was associated with participation restriction; prior status and change in a component were associated with current status in another component; and, the magnitude of the path coefficients varied over time with stronger associations among components to three months post surgery than later in recovery with the exception of the association between impairment and participation restrictions which was of similar magnitude at all times. This work enhances understanding of the

Control of selected VVER components life time SKODA JS a.s. experience

International Nuclear Information System (INIS)

Zdebor, J.; Pribulla, E.

2005-01-01

Experience from the operation of nuclear power plants with type VVER reactors has shown that the life time management of a number of nuclear reactor components is technically as well as with respect to safety substantiated even at the time which exceeds their originally designed life time. To accept such solution it was necessary to develop and implement a number of programs based on which it was possible to evaluate the actual condition of monitored equipment. It is a condition allowing to adopt solution concerning the possibility of their further operation. Experience from the manufacture of 21 sets of reactor equipment for VVER 440 and 3 sets VVER 1000 has been gathered in SKODA JS a.s. which have been completed by experience from service activities performed at operated nuclear power plants. Analyses of manufacturing data and in-service inspection results completed by a lot of laboratory tests have become the basis for the development of selected VVER components life time management programs. The paper focuses on the life time management of those VVER components which SKODA JS a.s. has most experience with. (authors)

Fast-Response-Time Shape-Memory-Effect Foam Actuators

Science.gov (United States)

Jardine, Peter

2010-01-01

the need for welding, adhesives, or mechanical crimping. Inexpensive net-shape processing was used, which reduces the cost of the actuator by over a factor of 10 over nonporous TiNi made by hot drawing of tube or electrical discharge machining. By forming the alloy as an open-celled foam, the surface area for heat transfer is dramatically increased, allowing for much faster response times. The technology also allows for netshape fabrication of the actuator, which allows for structural connections to be integrated into the actuator material, making these actuators significantly less expensive. Commercial applications include actuators for concepts such as the variable area chevron and nozzle in jet aircraft. Lightweight tube or rod components can be supplied to interested parties.

Immediate and heterogeneous response of the LiaFSR two-component system of Bacillus subtilis to the peptide antibiotic bacitracin.

Science.gov (United States)

Kesel, Sara; Mader, Andreas; Höfler, Carolin; Mascher, Thorsten; Leisner, Madeleine

2013-01-01

Two-component signal transduction systems are one means of bacteria to respond to external stimuli. The LiaFSR two-component system of Bacillus subtilis consists of a regular two-component system LiaRS comprising the core Histidine Kinase (HK) LiaS and the Response Regulator (RR) LiaR and additionally the accessory protein LiaF, which acts as a negative regulator of LiaRS-dependent signal transduction. The complete LiaFSR system was shown to respond to various peptide antibiotics interfering with cell wall biosynthesis, including bacitracin. Here we study the response of the LiaFSR system to various concentrations of the peptide antibiotic bacitracin. Using quantitative fluorescence microscopy, we performed a whole population study analyzed on the single cell level. We investigated switching from the non-induced 'OFF' state into the bacitracin-induced 'ON' state by monitoring gene expression of a fluorescent reporter from the RR-regulated liaI promoter. We found that switching into the 'ON' state occurred within less than 20 min in a well-defined switching window, independent of the bacitracin concentration. The switching rate and the basal expression rate decreased at low bacitracin concentrations, establishing clear heterogeneity 60 min after bacitracin induction. Finally, we performed time-lapse microscopy of single cells confirming the quantitative response as obtained in the whole population analysis for high bacitracin concentrations. The LiaFSR system exhibits an immediate, heterogeneous and graded response to the inducer bacitracin in the exponential growth phase.

Differential Contribution of RNA Interference Components in Response to Distinct Fusarium graminearum Virus Infections.

Science.gov (United States)

Yu, Jisuk; Lee, Kyung-Mi; Cho, Won Kyong; Park, Ju Yeon; Kim, Kook-Hyung

2018-05-01

The mechanisms of RNA interference (RNAi) as a defense response against viruses remain unclear in many plant-pathogenic fungi. In this study, we used reverse genetics and virus-derived small RNA profiling to investigate the contributions of RNAi components to the antiviral response against Fusarium graminearum viruses 1 to 3 (FgV1, -2, and -3). Real-time reverse transcription-quantitative PCR (qRT-PCR) indicated that infection of Fusarium graminearum by FgV1, -2, or -3 differentially induces the gene expression of RNAi components in F. graminearum Transcripts of the DICER-2 and AGO-1 genes of F. graminearum ( FgDICER-2 and FgAGO-1 ) accumulated at lower levels following FgV1 infection than following FgV2 or FgV3 infection. We constructed gene disruption and overexpression mutants for each of the Argonaute and dicer genes and for two RNA-dependent RNA polymerase (RdRP) genes and generated virus-infected strains of each mutant. Interestingly, mycelial growth was significantly faster for the FgV1-infected FgAGO-1 overexpression mutant than for the FgV1-infected wild type, while neither FgV2 nor FgV3 infection altered the colony morphology of the gene deletion and overexpression mutants. FgV1 RNA accumulation was significantly decreased in the FgAGO-1 overexpression mutant. Furthermore, the levels of induction of FgAGO-1 , FgDICER-2 , and some of the FgRdRP genes caused by FgV2 and FgV3 infection were similar to those caused by hairpin RNA-induced gene silencing. Using small RNA sequencing analysis, we documented different patterns of virus-derived small interfering RNA (vsiRNA) production in strains infected with FgV1, -2, and -3. Our results suggest that the Argonaute protein encoded by FgAGO-1 is required for RNAi in F. graminearum , that FgAGO-1 induction differs in response to FgV1, -2, and -3, and that FgAGO-1 might contribute to the accumulation of vsiRNAs in FgV1-infected F. graminearum IMPORTANCE To increase our understanding of how RNAi components in Fusarium

A Filtering of Incomplete GNSS Position Time Series with Probabilistic Principal Component Analysis

Science.gov (United States)

Gruszczynski, Maciej; Klos, Anna; Bogusz, Janusz

2018-04-01

For the first time, we introduced the probabilistic principal component analysis (pPCA) regarding the spatio-temporal filtering of Global Navigation Satellite System (GNSS) position time series to estimate and remove Common Mode Error (CME) without the interpolation of missing values. We used data from the International GNSS Service (IGS) stations which contributed to the latest International Terrestrial Reference Frame (ITRF2014). The efficiency of the proposed algorithm was tested on the simulated incomplete time series, then CME was estimated for a set of 25 stations located in Central Europe. The newly applied pPCA was compared with previously used algorithms, which showed that this method is capable of resolving the problem of proper spatio-temporal filtering of GNSS time series characterized by different observation time span. We showed, that filtering can be carried out with pPCA method when there exist two time series in the dataset having less than 100 common epoch of observations. The 1st Principal Component (PC) explained more than 36% of the total variance represented by time series residuals' (series with deterministic model removed), what compared to the other PCs variances (less than 8%) means that common signals are significant in GNSS residuals. A clear improvement in the spectral indices of the power-law noise was noticed for the Up component, which is reflected by an average shift towards white noise from - 0.98 to - 0.67 (30%). We observed a significant average reduction in the accuracy of stations' velocity estimated for filtered residuals by 35, 28 and 69% for the North, East, and Up components, respectively. CME series were also subjected to analysis in the context of environmental mass loading influences of the filtering results. Subtraction of the environmental loading models from GNSS residuals provides to reduction of the estimated CME variance by 20 and 65% for horizontal and vertical components, respectively.

Multi-Response Optimization of Wire Electrical Discharge Machining for Titanium Grade-5 by Weighted Principal Component Analysis

Directory of Open Access Journals (Sweden)

Sachin Ashok Sonawane

2018-04-01

Full Text Available This paper reports the results of research to examine the effects of cutting parameters such as pulse-on time, pulse-off time, servo voltage, peak current, wire feed rate and cable tension on surface finish, overcut and metal removal rate (MRR during Wire Electrical Discharge Machining (WEDM of grade-5 titanium (Ti-6Al-4V. Taguchi’s L27 orthogonal design method is used for experimentation. Multi-response optimization is performed by applying weighted principal component analysis (WPCA. The optimum values of cutting variables are found as a pulse on time 118 μs, pulse off time 45 μs, servo voltage 40 volts, peak current 190 Amp. , wire feed rate 5 m/min and cable tension 5 gram. On the other hand, Analysis of Variance (ANOVA, simulation results indicate that pulse-on time is the primary influencing variable which affects the response characteristics contributing 76.00%. The results of verification experiments show improvement in the value of output characteristics at the optimal cutting variables settings. Scanning electron microscopic (SEM analysis of the surface after machining indicates the formation of craters, resolidified material, tool material transfer and increase in the thickness of recast layer at higher values of the pulse on time.

Correlation of horizontal and vertical components of strong ground motion for response-history analysis of safety-related nuclear facilities

Energy Technology Data Exchange (ETDEWEB)

Huang, Yin-Nan, E-mail: ynhuang@ntu.edu.tw [Dept. of Civil Engineering, National Taiwan University, No. 1, Sec. 4, Roosevelt Rd., Taipei 10617, Taiwan (China); Yen, Wen-Yi, E-mail: b01501059@ntu.edu.tw [Dept. of Civil Engineering, National Taiwan University, No. 1, Sec. 4, Roosevelt Rd., Taipei 10617, Taiwan (China); Whittaker, Andrew S., E-mail: awhittak@buffalo.edu [Dept. of Civil, Structural and Environmental Engineering, MCEER, State University of New York at Buffalo, Buffalo, NY 14260 (United States)

2016-12-15

Highlights: • The correlation of components of ground motion is studied using 1689 sets of records. • The data support an upper bound of 0.3 on the correlation coefficient. • The data support the related requirement in the upcoming edition of ASCE Standard 4. - Abstract: Design standards for safety-related nuclear facilities such as ASCE Standard 4-98 and ASCE Standard 43-05 require the correlation coefficient for two orthogonal components of ground motions for response-history analysis to be less than 0.3. The technical basis of this requirement was developed by Hadjian three decades ago using 50 pairs of recorded ground motions that were available at that time. In this study, correlation coefficients for (1) two horizontal components, and (2) the vertical component and one horizontal component, of a set of ground motions are computed using records from a ground-motion database compiled recently for large-magnitude shallow crustal earthquakes. The impact of the orientation of the orthogonal horizontal components on the correlation coefficient of ground motions is discussed. The rules in the forthcoming edition of ASCE Standard 4 for the correlation of components in a set of ground motions are shown to be reasonable.

Temperature dependence of relaxation times in proton components of fatty acids

International Nuclear Information System (INIS)

Kuroda, Kagayaki; Iwabuchi, Taku; Saito, Kensuke; Obara, Makoto; Honda, Masatoshi; Imai, Yutaka

2011-01-01

We examined the temperature dependence of relaxation times in proton components of fatty acids in various samples in vitro at 11 tesla as a standard calibration data for quantitative temperature imaging of fat. The spin-lattice relaxation time, T 1 , of both the methylene (CH 2 ) chain and terminal methyl (CH 3 ) was linearly related to temperature (r>0.98, P 2 signal for calibration and observed the signal with 18% of CH 3 to estimate temperature. These findings suggested that separating the fatty acid components would significantly improve accuracy in quantitative thermometry for fat. Use of the T 1 of CH 2 seems promising in terms of reliability and reproducibility in measuring temperature of fat. (author)

Use of a Principal Components Analysis for the Generation of Daily Time Series.

Science.gov (United States)

Dreveton, Christine; Guillou, Yann

2004-07-01

A new approach for generating daily time series is considered in response to the weather-derivatives market. This approach consists of performing a principal components analysis to create independent variables, the values of which are then generated separately with a random process. Weather derivatives are financial or insurance products that give companies the opportunity to cover themselves against adverse climate conditions. The aim of a generator is to provide a wider range of feasible situations to be used in an assessment of risk. Generation of a temperature time series is required by insurers or bankers for pricing weather options. The provision of conditional probabilities and a good representation of the interannual variance are the main challenges of a generator when used for weather derivatives. The generator was developed according to this new approach using a principal components analysis and was applied to the daily average temperature time series of the Paris-Montsouris station in France. The observed dataset was homogenized and the trend was removed to represent correctly the present climate. The results obtained with the generator show that it represents correctly the interannual variance of the observed climate; this is the main result of the work, because one of the main discrepancies of other generators is their inability to represent accurately the observed interannual climate variance—this discrepancy is not acceptable for an application to weather derivatives. The generator was also tested to calculate conditional probabilities: for example, the knowledge of the aggregated value of heating degree-days in the middle of the heating season allows one to estimate the probability if reaching a threshold at the end of the heating season. This represents the main application of a climate generator for use with weather derivatives.

Sensor response time calculation with no stationary signals from a Nuclear Power Plant

International Nuclear Information System (INIS)

Vela, O.; Vallejo, I.

1998-01-01

Protection systems in a Nuclear Power Plant have to response in a specific time fixed by design requirements. This time includes the event detection (sensor delay) and the actuation time system. This time is obtained in refuel simulating the physics event, which trigger the protection system, with an electric signal and measuring the protection system actuation time. Nowadays sensor delay is calculated with noise analysis techniques. The signals are measured in Control Room during the normal operation of the Plant, decreasing both the cost in time and personal radioactive exposure. The noise analysis techniques require stationary signals but normally the data collected are mixed with process signals that are no stationary. This work shows the signals processing to avoid no-stationary components using conventional filters and new wavelets analysis. (Author) 2 refs

Generalization of risk concept in case risk components depend on time

International Nuclear Information System (INIS)

Volkov, Yu.V.

2006-01-01

Ratios of risk assessments vs. nuclear technologies objects have been obtained for cases when that kind of risk components as accident probability and the consequent damage depend on time. Such generalization of risk concept ensures new possibilities for performing the probabilistic safety analysis which have been demonstrated with simple models in the present paper. As an example safety of radioactive storage with one-component activity has been analyzed with a very simple model [ru

Response time patterns in a stated choice experiment

DEFF Research Database (Denmark)

Börjesson, Maria; Fosgerau, Mogens

2015-01-01

This paper studies how response times vary between unlabelled binary choice occasions in a stated choice (SC) experiment, with alternatives differing with respect to in-vehicle travel time and travel cost. The pattern of response times is interpreted as an indicator of the cognitive processes...... employed by the respondents when making their choices. We find clear signs of reference-dependence in response times in the form of a strong gain–loss asymmetry. Moreover, different patterns of response times for travel time and travel cost indicate that these attributes are processed in different ways...

Potential Response to Selection of HSP70 as a Component of Innate Immunity in the Abalone Haliotis rufescens

Science.gov (United States)

Brokordt, Katherina B.; González, Roxana C.; Farías, William J.; Winkler, Federico M.

2015-01-01

Assessing components of the immune system may reflect disease resistance. In some invertebrates, heat shock proteins (HSPs) are immune effectors and have been described as potent activators of the innate immune response. Several diseases have become a threat to abalone farming worldwide; therefore, increasing disease resistance is considered to be a long-term goal for breeding programs. A trait will respond to selection only if it is determined partially by additive genetic variation. The aim of this study was to estimate the heritability (h 2) and the additive genetic coefficient of variation (CV A) of HSP70 as a component of innate immunity of the abalone Haliotis rufescens, in order to assess its potential response to selection. These genetic components were estimated for the variations in the intracellular (in haemocytes) and extracellular (serum) protein levels of HSP70 in response to an immunostimulant agent in 60 full-sib families of H. rufescens. Levels of HSP70 were measured twice in the same individuals, first when they were young and again when they were pre-harvest adults, to estimate the repeatability (R), the h 2 and the potential response to selection of these traits at these life stages. High HSP70 levels were observed in abalones subjected to immunostimulation in both the intracellular and extracellular haemolymph fractions. This is the first time that changes in serum levels of HSP70 have been reported in response to an immune challenge in molluscs. HSP70 levels in both fractions and at both ages showed low h 2 and R, with values that were not significantly different from zero. However, HSP70 induced levels had a CV A of 13.3–16.2% in young adults and of 2.7–8.1% in pre-harvest adults. Thus, despite its low h 2, HSP70 synthesis in response to an immune challenge in red abalone has the potential to evolve through selection because of its large phenotypic variation and the presence of additive genetic variance, especially in young animals. PMID

Potential Response to Selection of HSP70 as a Component of Innate Immunity in the Abalone Haliotis rufescens.

Directory of Open Access Journals (Sweden)

Katherina B Brokordt

Full Text Available Assessing components of the immune system may reflect disease resistance. In some invertebrates, heat shock proteins (HSPs are immune effectors and have been described as potent activators of the innate immune response. Several diseases have become a threat to abalone farming worldwide; therefore, increasing disease resistance is considered to be a long-term goal for breeding programs. A trait will respond to selection only if it is determined partially by additive genetic variation. The aim of this study was to estimate the heritability (h2 and the additive genetic coefficient of variation (CVA of HSP70 as a component of innate immunity of the abalone Haliotis rufescens, in order to assess its potential response to selection. These genetic components were estimated for the variations in the intracellular (in haemocytes and extracellular (serum protein levels of HSP70 in response to an immunostimulant agent in 60 full-sib families of H. rufescens. Levels of HSP70 were measured twice in the same individuals, first when they were young and again when they were pre-harvest adults, to estimate the repeatability (R, the h2 and the potential response to selection of these traits at these life stages. High HSP70 levels were observed in abalones subjected to immunostimulation in both the intracellular and extracellular haemolymph fractions. This is the first time that changes in serum levels of HSP70 have been reported in response to an immune challenge in molluscs. HSP70 levels in both fractions and at both ages showed low h2 and R, with values that were not significantly different from zero. However, HSP70 induced levels had a CVA of 13.3-16.2% in young adults and of 2.7-8.1% in pre-harvest adults. Thus, despite its low h2, HSP70 synthesis in response to an immune challenge in red abalone has the potential to evolve through selection because of its large phenotypic variation and the presence of additive genetic variance, especially in young animals.

The inspection of components by X ray in real time in automobile industry

International Nuclear Information System (INIS)

Demandt, K.

1987-01-01

Besides a brief introduction to the state of the art of automobile components inspection by radiography in real time, some examples are discussed. New developments and a possible application for automobile components inspection by x-radiation are discussed. (E.G.) [pt

Precise response function for the magnetic component of gravitational waves in scalar-tensor gravity

International Nuclear Information System (INIS)

Corda, Christian

2011-01-01

The important issue of the magnetic component of gravitational waves (GWs) has been considered in various papers in the literature. From such analyses, it has been found that such a magnetic component becomes particularly important in the high-frequency portion of the frequency range of ground based interferometers for GWs which arises from standard general theory of relativity (GTR). Recently, such a magnetic component has been extended to GWs arising from scalar-tensor gravity (STG) too. After a review of some important issues on GWs in STG, in this paper we reanalyze the magnetic component in the framework of STG from a different point of view, by correcting an error in a previous paper and by releasing a more precise response function. In this way, we also show that if one neglects the magnetic contribution considering only the low-frequency approximation of the electric contribution, an important part of the signal could be, in principle, lost. The determination of a more precise response function for the magnetic contribution is important also in the framework of the possibility of distinguishing other gravitational theories from GTR. At the conclusion of this paper, an expansion of the main results is also shown in order to recall the presence of the magnetic component in GTR too.

Space-time latent component Modeling of Geo-referenced health data

OpenAIRE

Lawson, Andrew B.; Song, Hae-Ryoung; Cai, Bo; Hossain, Md Monir; Huang, Kun

2010-01-01

Latent structure models have been proposed in many applications. For space time health data it is often important to be able to find underlying trends in time which are supported by subsets of small areas. Latent structure modeling is one approach to this analysis. This paper presents a mixture-based approach that can be appied to component selction. The analysis of a Georgia ambulatory asthma county level data set is presented and a simulation-based evaluation is made.

Cognitive Reflection, Decision Biases, and Response Times.

Science.gov (United States)

Alós-Ferrer, Carlos; Garagnani, Michele; Hügelschäfer, Sabine

2016-01-01

We present novel evidence on response times and personality traits in standard questions from the decision-making literature where responses are relatively slow (medians around half a minute or above). To this end, we measured response times in a number of incentivized, framed items (decisions from description) including the Cognitive Reflection Test, two additional questions following the same logic, and a number of classic questions used to study decision biases in probability judgments (base-rate neglect, the conjunction fallacy, and the ratio bias). All questions create a conflict between an intuitive process and more deliberative thinking. For each item, we then created a non-conflict version by either making the intuitive impulse correct (resulting in an alignment question), shutting it down (creating a neutral question), or making it dominant (creating a heuristic question). For CRT questions, the differences in response times are as predicted by dual-process theories, with alignment and heuristic variants leading to faster responses and neutral questions to slower responses than the original, conflict questions. For decision biases (where responses are slower), evidence is mixed. To explore the possible influence of personality factors on both choices and response times, we used standard personality scales including the Rational-Experiential Inventory and the Big Five, and used them as controls in regression analysis.

Individual differences in anxiety responses to stressful situations : A three-mode component analysis model

NARCIS (Netherlands)

Van Mechelen, Iven; Kiers, Henk A.L.

1999-01-01

The three-mode component analysis model is discussed as a tool for a contextualized study of personality. When applied to person x situation x response data, the model includes sets of latent dimensions for persons, situations, and responses as well as a so-called core array, which may be considered

The Effect of Sports and Physical Activity on Elderly Reaction Time and Response Time

Directory of Open Access Journals (Sweden)

Abdolrahman Khezri

2014-07-01

Full Text Available Objectives: Physical activities ameliorate elderly motor and cognitive performance. The aim of this research is to study the effect of sport and physical activity on elderly reaction time and response time. Methods & Materials: The research method is causal-comparative and its statistical population consists of 60 active and non-active old males over 60 years residing at Mahabad city. Reaction time was measured by reaction timer apparatus, made in Takei Company (YB1000 model. Response time was measured via Nelson’s Choice- Response Movement Test. At first, reaction time and then response time was measured. For data analysis, descriptive statistic, K-S Test and One Sample T Test were used Results K-S Test show that research data was parametric. According to the results of this research, physical activity affected reaction time and response time. Results: of T test show that reaction time (P=0.000 and response time (P=0.000 of active group was statistically shorter than non- active group. Conclusion: The result of current study demonstrate that sport and physical activity, decrease reaction and response time via psychomotor and physiological positive changes.

A Box-Cox normal model for response times.

Science.gov (United States)

Klein Entink, R H; van der Linden, W J; Fox, J-P

2009-11-01

The log-transform has been a convenient choice in response time modelling on test items. However, motivated by a dataset of the Medical College Admission Test where the lognormal model violated the normality assumption, the possibilities of the broader class of Box-Cox transformations for response time modelling are investigated. After an introduction and an outline of a broader framework for analysing responses and response times simultaneously, the performance of a Box-Cox normal model for describing response times is investigated using simulation studies and a real data example. A transformation-invariant implementation of the deviance information criterium (DIC) is developed that allows for comparing model fit between models with different transformation parameters. Showing an enhanced description of the shape of the response time distributions, its application in an educational measurement context is discussed at length.

Time response for sensor sensed to actuator response for mobile robotic system

Science.gov (United States)

Amir, N. S.; Shafie, A. A.

2017-11-01

Time and performance of a mobile robot are very important in completing the tasks given to achieve its ultimate goal. Tasks may need to be done within a time constraint to ensure smooth operation of a mobile robot and can result in better performance. The main purpose of this research was to improve the performance of a mobile robot so that it can complete the tasks given within time constraint. The problem that is needed to be solved is to minimize the time interval between sensor detection and actuator response. The research objective is to analyse the real time operating system performance of sensors and actuators on one microcontroller and on two microcontroller for a mobile robot. The task for a mobile robot for this research is line following with an obstacle avoidance. Three runs will be carried out for the task and the time between the sensors senses to the actuator responses were recorded. Overall, the results show that two microcontroller system have better response time compared to the one microcontroller system. For this research, the average difference of response time is very important to improve the internal performance between the occurrence of a task, sensors detection, decision making and actuator response of a mobile robot. This research helped to develop a mobile robot with a better performance and can complete task within the time constraint.

The main component of an alarm pheromone of kissing bugs plays multiple roles in the cognitive modulation of the escape response

Directory of Open Access Journals (Sweden)

Sebastián eMinoli

2013-07-01

Full Text Available Innate responses in animals can be modulated by experience. Disturbed adults of the triatomine bug Triatoma infestans release an alarm pheromone (AP that elicits an escape response in conspecific larvae. The main component of this AP, the isobutyric acid (IsoAc, alone has already shown to generate an escape response in this species. However, not much is known about the modulation of this behavior by non-associative and associative cognitive processes. We present here evidences of the cognitive capacities of T. infestans larvae in an escape context under different conditioning paradigms, including IsoAc in different roles. We show that: 1 the duration of a pre-exposure to IsoAc plays a main role in determining the type of non-associative learning expressed: short time pre-exposures elicit a sensitization while a longer pre-exposure time triggers a switch from repellence to attractiveness; 2 a simple pre-exposure event is enough to modulate the escape response of larvae to the AP and to its main component: IsoAc; 3 IsoAc and the AP are perceived as different chemical entities; 4 an association between IsoAc and an aversive stimulus can be created under a classical conditioning paradigm; 5 an association between IsoAc and a self-action can be generated under an operant conditioning. These results evince that IsoAc can attain multiple and different cognitive roles in the modulation of the escape response of triatomines and show how cognitive processes can modulate a key behavior for surviving, as it is the escaping response in presence of a potential danger in insects.

COMDES-II: A Component-Based Framework for Generative Development of Distributed Real-Time Control Systems

DEFF Research Database (Denmark)

Ke, Xu; Sierszecki, Krzysztof; Angelov, Christo K.

2007-01-01

The paper presents a generative development methodology and component models of COMDES-II, a component-based software framework for distributed embedded control systems with real-time constraints. The adopted methodology allows for rapid modeling and validation of control software at a higher lev...... methodology for COMDES-II from a general perspective, describes the component models in details and demonstrates their application through a DC-Motor control system case study.......The paper presents a generative development methodology and component models of COMDES-II, a component-based software framework for distributed embedded control systems with real-time constraints. The adopted methodology allows for rapid modeling and validation of control software at a higher level...

Questionnaire: involved actors in large disused components management - Summary Of Responses To The Questionnaire

International Nuclear Information System (INIS)

2012-01-01

The aim of the Questionnaire is to establish an overview of the various bodies [Actors] that have responsibilities or input to the issue of large component decommissioning. In answering the intent is to cover the overall organisation and those bits that have most relevance to large components. The answers should reflect the areas from site operations to decommissioning as well as the wider issue of disposal at another location. The Questionnaire covers the following points: 1 - What is the country (institutional) structure for decommissioning? 2 - who does what and where lie the responsibilities? 3 - Which bodies have responsibility for onsite safety regulation, discharges and disposal? 4 - Which body(s) owns the facilities? 5 - Describe the responsibilities for funding of the decommissioning plan and disposal plan. Are they one and the same body? Whilst there are differences between countries there are some common threads. Regulation is through the state though the number of regulators involved may vary. In summary, the IAEA principles concerning independence of the regulatory body are followed. Funding arrangements vary but there are plans. Similarly, ownership of facilities is a mix of state and private. Some systems require a separate decommissioning license with Spain having the clearest demarcation of responsibilities for the decommissioning phase and waste management responsibilities

Efficient block preconditioned eigensolvers for linear response time-dependent density functional theory

Energy Technology Data Exchange (ETDEWEB)

Vecharynski, Eugene [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Computational Research Division; Brabec, Jiri [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Computational Research Division; Shao, Meiyue [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Computational Research Division; Govind, Niranjan [Pacific Northwest National Lab. (PNNL), Richland, WA (United States). Environmental Molecular Sciences Lab.; Yang, Chao [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Computational Research Division

2017-12-01

We present two efficient iterative algorithms for solving the linear response eigen- value problem arising from the time dependent density functional theory. Although the matrix to be diagonalized is nonsymmetric, it has a special structure that can be exploited to save both memory and floating point operations. In particular, the nonsymmetric eigenvalue problem can be transformed into a product eigenvalue problem that is self-adjoint with respect to a K-inner product. This product eigenvalue problem can be solved efficiently by a modified Davidson algorithm and a modified locally optimal block preconditioned conjugate gradient (LOBPCG) algorithm that make use of the K-inner product. The solution of the product eigenvalue problem yields one component of the eigenvector associated with the original eigenvalue problem. However, the other component of the eigenvector can be easily recovered in a postprocessing procedure. Therefore, the algorithms we present here are more efficient than existing algorithms that try to approximate both components of the eigenvectors simultaneously. The efficiency of the new algorithms is demonstrated by numerical examples.

The Value of Response Times in Item Response Modeling

Science.gov (United States)

Molenaar, Dylan

2015-01-01

A new and very interesting approach to the analysis of responses and response times is proposed by Goldhammer (this issue). In his approach, differences in the speed-ability compromise within respondents are considered to confound the differences in ability between respondents. These confounding effects of speed on the inferences about ability can…

Equilibrium and response properties of the integrate-and-fire neuron in discrete time

Directory of Open Access Journals (Sweden)

Moritz Helias

2010-01-01

Full Text Available The integrate-and-fire neuron with exponential postsynaptic potentials is a frequently employed model to study neural networks. Simulations in discrete time still have highest performance at moderate numerical errors, which makes them first choice for long-term simulations of plastic networks. Here we extend the population density approach to investigate how the equilibrium and response properties of the leaky integrate-and-fire neuron are affected by time discretization. We present a novel analytical treatment of the boundary condition at threshold, taking both discretization of time and finite synaptic weights into account. We uncover an increased membrane potential density just below threshold as the decisive property that explains the deviations found between simulations and the classical diffusion approximation. Temporal discretization and finite synaptic weights both contribute to this effect. Our treatment improves the standard formula to calculate the neuron’s equilibrium firing rate. Direct solution of the Markov process describing the evolution of the membrane potential density confirms our analysis and yields a method to calculate the firing rate exactly. Knowing the shape of the membrane potential distribution near threshold enables us to devise the transient response properties of the neuron model to synaptic input. We find a pronounced non-linear fast response component that has not been described by the prevailing continuous time theory for Gaussian white noise input.

Sensor response time monitoring using noise analysis

International Nuclear Information System (INIS)

Hashemian, H.M.; Thie, J.A.; Upadhyaya, B.R.; Holbert, K.E.

1988-01-01

Random noise techniques in nuclear power plants have been developed for system surveillance and for analysis of reactor core dynamics. The noise signals also contain information about sensor dynamics, and this can be extracted using frequency, amplitude and time domain analyses. Even though noise analysis has been used for sensor response time testing in some nuclear power plants, an adequate validation of this method has never been carried out. This paper presents the results of limited work recently performed to examine the validity of the noise analysis for sensor response time testing in nuclear power plants. The conclusion is that noise analysis has the potential for detecting gross changes in sensor response but it cannot be used for reliable measurement of response time until more laboratory and field experience is accumulated. The method is more advantageous for testing pressure sensors than it is for temperature sensors. This is because: 1) for temperature sensors, a method called Loop Current Step Response test is available which is quantitatively more exact than noise analysis, 2) no method currently exists for on-line testing of pressure transmitters other than the Power-Interrupt test which is applicable only to force balance pressure transmitters, and 3) pressure sensor response time is affected by sensing line degradation which is inherently taken into account by testing with noise analysis. (author)

Space-time latent component modeling of geo-referenced health data.

Science.gov (United States)

Lawson, Andrew B; Song, Hae-Ryoung; Cai, Bo; Hossain, Md Monir; Huang, Kun

2010-08-30

Latent structure models have been proposed in many applications. For space-time health data it is often important to be able to find the underlying trends in time, which are supported by subsets of small areas. Latent structure modeling is one such approach to this analysis. This paper presents a mixture-based approach that can be applied to component selection. The analysis of a Georgia ambulatory asthma county-level data set is presented and a simulation-based evaluation is made. Copyright (c) 2010 John Wiley & Sons, Ltd.

Response and recovery of water yield and timing, stream sediment, abiotic parameters, and stream chemistry following logging

Science.gov (United States)

Wayne Swank; Jennifer Knoepp; James Vose; Stephanie Laseter; Jackson Webster

2014-01-01

Watershed ecosystem analysis provides a scientific approach to quantify and integrate resource responses to management (Hornbeck and Swank 1992) and also to address issues of resource sustainability (Christensen et. al. 1996). Philosophical components of the research approach at Coweeta are 1) the quantity, timing, and quality of streamflow provides an integrated...

Incorporating Response Times in Item Response Theory Models of Reading Comprehension Fluency

Science.gov (United States)

Su, Shiyang

2017-01-01

With the online assessment becoming mainstream and the recording of response times becoming straightforward, the importance of response times as a measure of psychological constructs has been recognized and the literature of modeling times has been growing during the last few decades. Previous studies have tried to formulate models and theories to…

QUANTITATION OF MOLECULAR ENDPOINTS FOR THE DOSE-RESPONSE COMPONENT OF CANCER RISK ASSESSMENT

Science.gov (United States)

Cancer risk assessment involves the steps of hazard identification, dose-response assessment, exposure assessment and risk characterization. The rapid advances in the use of molecular biology approaches has had an impact on all four components, but the greatest overall current...

Capturing Real-Time Data in Disaster Response Logistics

Directory of Open Access Journals (Sweden)

Kezban Yagci Sokat

2016-06-01

Full Text Available The volume, accuracy, accessibility and level of detail of near real-time data emerging from disaster-affected regions continue to significantly improve. Integration of dynamically evolving in-field data is an important, yet often overlooked, component of the humanitarian logistics models. In this paper, we present a framework for real-time humanitarian logistics data focused on use in mathematical modeling along with modeling implications of this framework. We also discuss how one might measure the attributes of the framework and describe the application of the presented framework to a case study of near real-time data collection in the days following the landfall of Typhoon Haiyan. We detail our first-hand experience of capturing data as the post-disaster response unfolds starting on November 10, 2013 until March 31, 2014 and assess the characteristics and evolution of data pertaining to humanitarian logistics modeling using the proposed framework. The presented logistical content analysis examines the availability of data and informs modelers about the current state of near real-time data. This analysis illustrates what data is available, how early it is available, and how data changes after the disaster. The study describes how our humanitarian logistics team approached the emergence of dynamic online data after the disaster and the challenges faced during the collection process, as well as recommendations to address these challenges in the future (when possible from an academic humanitarian logistics perspective.

Verification of the local structural response of building structures in the anchorage areas of heavy components

International Nuclear Information System (INIS)

Krutzik, N.J.; Tropp, R.

1989-01-01

In conventional dynamic structural analyses for determining dynamic system response for various locations at which components are installed inside the structures it is common practice (in order to simplify analytical effort) to assume that the anchorage (anchor plate, anchor bolts or throughbolts, concrete and reinforcement in the area of bound) has rigid body characteristics and that the building structure itself does not display any local response of its own. The influence of the stiffness of the anchor plate as well anchor bolts and its stress level on the dynamic response is also neglected. For a large number of anchoring systems, especially for all those components and systems having only a small mass, this assumption is certainly appropriate. At some locations, particularly at points where heavy components are anchored or when loading input has been increased, this can lead to local loading of the anchor system as well as of the building structure well into the nonlinear range. Often, verification of capability to accommodate these loads is not possible without changing the wall thicknesses or increasing the percentage of reinforcement. Since the presence of linear or nonlinear effects can be expected to result in energy dissipation (increase in damping capacity and also a change in the stiffness of the coupled system) it must be assumed that the dynamic response between the theoretical coupling point A and the real connection point B of the component on the anchor plate can be considerably altered. Some changes of the dynamic response in the connection point B have to be expected generally even in cases of linear-elastic loading of the anchorage. Using typical anchoring systems as an example, the influence of consideration of nonlinear effects in the anchorage area of a typical anchor plate on the dynamic response as well as the conservatism of conventional analytical approaches are investigated

Sensory-specific clock components and memory mechanisms: investigation with parallel timing.

Science.gov (United States)

Gamache, Pierre-Luc; Grondin, Simon

2010-05-01

A challenge for researchers in the time-perception field is to determine whether temporal processing is governed by a central mechanism or by multiple mechanisms working in concert. Behavioral studies of parallel timing offer interesting insights into the question, although the conclusions fail to converge. Most of these studies focus on the number-of-clocks issue, but the commonality of memory mechanisms involved in time processing is often neglected. The present experiment aims to address a straightforward question: do signals from different modalities marking time intervals share the same clock and/or the same memory resources? To this end, an interval reproduction task involving the parallel timing of two sensory signals presented either in the same modality or in different modalities was conducted. The memory component was tested by manipulating the delay separating the presentation of the target intervals and the moment when the reproduction of one of these began. Results show that there is more variance when only visually marked intervals are presented, and this effect is exacerbated with longer retention delays. Finally, when there is only one interval to process, encoding the interval with signals delivered from two modalities helps to reduce variance. Taken together, these results suggest that the hypothesis stating that there are sensory-specific clock components and memory mechanisms is viable.

Response times of operators in a control room

International Nuclear Information System (INIS)

Platz, O.; Rasmussen, J.; Skanborg, P.Z.

1982-12-01

A statistical analysis was made of operator response times recorded in the control room of a research reactor during the years 1972-1974. A homogeneity test revealed that the data consist of a mixture of populations. A small but statistically significant difference is found between day and night response times. Lognormal distributions are found to provide the best fit of the day and the night response times. (author)

Distributed BOLD-response in association cortex vector state space predicts reaction time during selective attention.

Science.gov (United States)

Musso, Francesco; Konrad, Andreas; Vucurevic, Goran; Schäffner, Cornelius; Friedrich, Britta; Frech, Peter; Stoeter, Peter; Winterer, Georg

2006-02-15

Human cortical information processing is thought to be dominated by distributed activity in vector state space (Churchland, P.S., Sejnowski, T.J., 1992. The Computational Brain. MIT Press, Cambridge.). In principle, it should be possible to quantify distributed brain activation with independent component analysis (ICA) through vector-based decomposition, i.e., through a separation of a mixture of sources. Using event-related functional magnetic resonance imaging (fMRI) during a selective attention-requiring task (visual oddball), we explored how the number of independent components within activated cortical areas is related to reaction time. Prior to ICA, the activated cortical areas were determined on the basis of a General linear model (GLM) voxel-by-voxel analysis of the target stimuli (checkerboard reversal). Two activated cortical areas (temporoparietal cortex, medial prefrontal cortex) were further investigated as these cortical regions are known to be the sites of simultaneously active electromagnetic generators which give rise to the compound event-related potential P300 during oddball task conditions. We found that the number of independent components more strongly predicted reaction time than the overall level of "activation" (GLM BOLD-response) in the left temporoparietal area whereas in the medial prefrontal cortex both ICA and GLM predicted reaction time equally well. Comparable correlations were not seen when principle components were used instead of independent components. These results indicate that the number of independently activated components, i.e., a high level of cortical activation complexity in cortical vector state space, may index particularly efficient information processing during selective attention-requiring tasks. To our best knowledge, this is the first report describing a potential relationship between neuronal generators of cognitive processes, the associated electrophysiological evidence for the existence of distributed networks

Review of Maintenance and Repair Times for Components in Technological Facilities

Energy Technology Data Exchange (ETDEWEB)

L. C. Cadwallader

2012-11-01

This report is a compilation of some unique component repair time data and it also presents citations of more extensive reports where lists of repair times can be found. This collection of information should support analysts who seek to quantify maintainability and availability of high technology and nuclear energy production systems. While there are newer sources of repair time information, most, if not all, of the newer sources are proprietary and cannot be shared. This report offers data that, while older, is openly accessible and can serve as reasonable estimates of repair times, at least for initial studies. Some times were found for maintenance times in radiation environments, and some guidance for multiplicative factors to use to account for work in contamination areas.

Joint Testlet Cognitive Diagnosis Modeling for Paired Local Item Dependence in Response Times and Response Accuracy

Directory of Open Access Journals (Sweden)

Peida Zhan

2018-04-01

Full Text Available In joint models for item response times (RTs and response accuracy (RA, local item dependence is composed of local RA dependence and local RT dependence. The two components are usually caused by the same common stimulus and emerge as pairs. Thus, the violation of local item independence in the joint models is called paired local item dependence. To address the issue of paired local item dependence while applying the joint cognitive diagnosis models (CDMs, this study proposed a joint testlet cognitive diagnosis modeling approach. The proposed approach is an extension of Zhan et al. (2017 and it incorporates two types of random testlet effect parameters (one for RA and the other for RTs to account for paired local item dependence. The model parameters were estimated using the full Bayesian Markov chain Monte Carlo (MCMC method. The 2015 PISA computer-based mathematics data were analyzed to demonstrate the application of the proposed model. Further, a brief simulation study was conducted to demonstrate the acceptable parameter recovery and the consequence of ignoring paired local item dependence.

Derivation of design response spectra for analysis and testing of components and systems

International Nuclear Information System (INIS)

Krutzik, N.

1996-01-01

Some institutions participating in the Benchmark Project performed parallel calculations for the WWER-1000 Kozloduy NPP. The investigations were based on various mathematical models and procedures for consideration of soil-structure interaction effects, simultaneously applying uniform soil dynamic and seismological input data. The methods, mathematical models and dynamic response results were evaluated and discussed in detail and finally compared by means of different structural models and soil representations with the aim of deriving final enveloped and smoothed dynamic response data (benchmark response spectra). This should be used for requalification by analysis testing of the mechanical and electrical components and systems located in this type of reactor building

Response time scores on a reflexive attention task predict a child's inattention score from a parent report.

Science.gov (United States)

Lundwall, Rebecca A; Sgro, Jordan F; Fanger, Julia

2018-01-01

Compared to sustained attention, only a small proportion of studies examine reflexive attention as a component of everyday attention. Understanding the significance of reflexive attention to everyday attention may inform better treatments for attentional disorders. Children from a general population (recruited when they were from 9-16 years old) completed an exogenously-cued task measuring the extent to which attention is captured by peripheral cue-target conditions. Parents completed a questionnaire reporting their child's day-to-day attention. A general linear model indicated that parent-rated inattention predicted the increase in response time over baseline when a bright cue preceded the target (whether it was valid or invalid) but not when a dim cue preceded the target. More attentive children had more pronounced response time increases from baseline. Our findings suggest a link between a basic measure of cognition (response time difference scores) and parent observations. The findings have implications for increased understanding of the role of reflexive attention in the everyday attention of children.

A Comparison of Response Rate, Response Time, and Costs of Mail and Electronic Surveys.

Science.gov (United States)

Shannon, David M.; Bradshaw, Carol C.

2002-01-01

Compared response rates, response time, and costs of mail and electronic surveys using a sample of 377 college faculty members. Mail surveys yielded a higher response rate and a lower rate of undeliverable surveys, but response time was longer and costs were higher than for electronic surveys. (SLD)

A multi-component and multi-failure mode inspection model based on the delay time concept

International Nuclear Information System (INIS)

Wang Wenbin; Banjevic, Dragan; Pecht, Michael

2010-01-01

The delay time concept and the techniques developed for modelling and optimising plant inspection practices have been reported in many papers and case studies. For a system comprised of many components and subject to many different failure modes, one of the most convenient ways to model the inspection and failure processes is to use a stochastic point process for defect arrivals and a common delay time distribution for the duration between defect the arrival and failure of all defects. This is an approximation, but has been proven to be valid when the number of components is large. However, for a system with just a few key components and subject to few major failure modes, the approximation may be poor. In this paper, a model is developed to address this situation, where each component and failure mode is modelled individually and then pooled together to form the system inspection model. Since inspections are usually scheduled for the whole system rather than individual components, we then formulate the inspection model when the time to the next inspection from the point of a component failure renewal is random. This imposes some complication to the model, and an asymptotic solution was found. Simulation algorithms have also been proposed as a comparison to the analytical results. A numerical example is presented to demonstrate the model.

Optimization of microwave-assisted extraction (MAP) for ginseng components by response surface methodology.

Science.gov (United States)

Kwon, Joong-Ho; Bélanger, Jacqueline M R; Paré, J R Jocelyn

2003-03-26

Response surface methodology (RSM) was applied to predict optimum conditions for microwave-assisted extraction-a MAP technology-of saponin components from ginseng roots. A central composite design was used to monitor the effect of ethanol concentration (30-90%, X(1)) and extraction time (30-270 s, X(2)) on dependent variables, such as total extract yield (Y(1)), crude saponin content (Y(2)), and saponin ratio (Y(3)), under atmospheric pressure conditions when focused microwaves were applied at an emission frequency of 2450 MHz. In MAP under pre-established conditions, correlation coefficients (R (2)) of the models for total extract yield and crude saponin were 0.9841 (p extraction conditions were predicted for each variable as 52.6% ethanol and 224.7 s in extract yield and as 77.3% ethanol and 295.1 s in crude saponins, respectively. Estimated maximum values at predicted optimum conditions were in good agreement with experimental values.

Two component systems: physiological effect of a third component.

Directory of Open Access Journals (Sweden)

Baldiri Salvado

Full Text Available Signal transduction systems mediate the response and adaptation of organisms to environmental changes. In prokaryotes, this signal transduction is often done through Two Component Systems (TCS. These TCS are phosphotransfer protein cascades, and in their prototypical form they are composed by a kinase that senses the environmental signals (SK and by a response regulator (RR that regulates the cellular response. This basic motif can be modified by the addition of a third protein that interacts either with the SK or the RR in a way that could change the dynamic response of the TCS module. In this work we aim at understanding the effect of such an additional protein (which we call "third component" on the functional properties of a prototypical TCS. To do so we build mathematical models of TCS with alternative designs for their interaction with that third component. These mathematical models are analyzed in order to identify the differences in dynamic behavior inherent to each design, with respect to functionally relevant properties such as sensitivity to changes in either the parameter values or the molecular concentrations, temporal responsiveness, possibility of multiple steady states, or stochastic fluctuations in the system. The differences are then correlated to the physiological requirements that impinge on the functioning of the TCS. This analysis sheds light on both, the dynamic behavior of synthetically designed TCS, and the conditions under which natural selection might favor each of the designs. We find that a third component that modulates SK activity increases the parameter space where a bistable response of the TCS module to signals is possible, if SK is monofunctional, but decreases it when the SK is bifunctional. The presence of a third component that modulates RR activity decreases the parameter space where a bistable response of the TCS module to signals is possible.

A semi-parametric within-subject mixture approach to the analyses of responses and response times.

Science.gov (United States)

Molenaar, Dylan; Bolsinova, Maria; Vermunt, Jeroen K

2018-05-01

In item response theory, modelling the item response times in addition to the item responses may improve the detection of possible between- and within-subject differences in the process that resulted in the responses. For instance, if respondents rely on rapid guessing on some items but not on all, the joint distribution of the responses and response times will be a multivariate within-subject mixture distribution. Suitable parametric methods to detect these within-subject differences have been proposed. In these approaches, a distribution needs to be assumed for the within-class response times. In this paper, it is demonstrated that these parametric within-subject approaches may produce false positives and biased parameter estimates if the assumption concerning the response time distribution is violated. A semi-parametric approach is proposed which resorts to categorized response times. This approach is shown to hardly produce false positives and parameter bias. In addition, the semi-parametric approach results in approximately the same power as the parametric approach. © 2017 The British Psychological Society.

Distinguishing deterministic and noise components in ELM time series

International Nuclear Information System (INIS)

Zvejnieks, G.; Kuzovkov, V.N

2004-01-01

Full text: One of the main problems in the preliminary data analysis is distinguishing the deterministic and noise components in the experimental signals. For example, in plasma physics the question arises analyzing edge localized modes (ELMs): is observed ELM behavior governed by a complicate deterministic chaos or just by random processes. We have developed methodology based on financial engineering principles, which allows us to distinguish deterministic and noise components. We extended the linear auto regression method (AR) by including the non-linearity (NAR method). As a starting point we have chosen the nonlinearity in the polynomial form, however, the NAR method can be extended to any other type of non-linear functions. The best polynomial model describing the experimental ELM time series was selected using Bayesian Information Criterion (BIC). With this method we have analyzed type I ELM behavior in a subset of ASDEX Upgrade shots. Obtained results indicate that a linear AR model can describe the ELM behavior. In turn, it means that type I ELM behavior is of a relaxation or random type

The Importance of Responsibility in Times of Crisis

Directory of Open Access Journals (Sweden)

Jacob Dahl Rendtorff

2014-06-01

Full Text Available In this paper I would like to show the importance of the concept of responsibility as the foundation of ethics in times of crisis in particular in the fields of politics and economics in the modern civilisation marked by globalization and technological progres. I consider the concept of responsibility as the key notion in order to understand the ethical duty in a modern technological civilisation. We can indeed observe a moralization of the concept of responsibility going beyond a strict legal definition in terms of imputability. The paper begins by discussing the humanistic foundations of such a concept of responsibility. It treats the historical origins of responsibility and it relates this concept to the concept of accountability. On the basis of this historical determination of the concept I would like to present the definition of the concept of responsibility as fundamental ethical principle that has increasing importance as the foundation of the principles of governance in modern welfare states. In this context the paper discusses the extension of the concept of responsibility towards institutional or corporate responsibility where responsibility does not only concerns the responsibility of individuals but also deals with the responsibility of institutional collectivities. In this way the paper is based on the following structure : 1 The ethical foundation of the concept of responsibility 2 Responsibility in technological civilisation 3 Political responsibility for good governance in the welfare state 4 Social responsibility of business corporations in times of globalization 5 Conclusion and discussion : changed conditions of responsibility in modern times.

Pressure/cross-sectional area relations in the proximal urethra of healthy males. Part III: the time dependent pressure response following forced dilation: standardization of a technique

DEFF Research Database (Denmark)

Bagi, Per

2002-01-01

(beta) are time constants. The size and velocity of dilation, as well as the degree of distension before dilation, proved of significance for the magnitude of the pressure response. The characteristics of the pressure response are given by the properties of the periluminal structures strained during dilation......, and are thus predominantly determined of elastic, collagen, muscular, and glandular components. However, a high degree of relaxation after straining, and a modest stiffness, indicates that the muscular component dominates the response. The significance of the prostatic tissues remains unclear....

Study on time characteristics of fast time response inorganic scintillator CeF3

International Nuclear Information System (INIS)

Hu Mengchun; Zhou Dianzhong; Guo Cun; Ye Wenying

2003-01-01

The cerium fluoride (CeF 3 ) is a kind of new fast time response inorganic scintillator. The physical characteristics of CeF 3 are well suitable for detection of domestic pulse γ-rays. The time response of detector composed by phototube with CeF 3 are measured by use of the pulse radiation source with rise time about 0.8 ns, and FWHM time 1.5-2.2 ns. Experiment results show that the rise time is less than 2 ns, FWHM time is about 10 ns, fall time is about 60 ns, average decay time constant is 20-30 ns, respectively for CeF 3

Conceptual question response times in Peer Instruction classrooms

Directory of Open Access Journals (Sweden)

Kelly Miller

2014-08-01

Full Text Available Classroom response systems are widely used in interactive teaching environments as a way to engage students by asking them questions. Previous research on the time taken by students to respond to conceptual questions has yielded insights on how students think and change conceptions. We measure the amount of time students take to respond to in-class, conceptual questions [ConcepTests (CTs] in two introductory physics courses taught using Peer Instruction and use item response theory to determine the difficulty of the CTs. We examine response time differences between correct and incorrect answers both before and after the peer discussion for CTs of varying difficulty. We also determine the relationship between response time and student performance on a standardized test of incoming physics knowledge, precourse self-efficacy, and gender. Our data reveal three results of interest. First, response time for correct answers is significantly faster than for incorrect answers, both before and after peer discussion, especially for easy CTs. Second, students with greater incoming physics knowledge and higher self-efficacy respond faster in both rounds. Third, there is no gender difference in response rate after controlling for incoming physics knowledge scores, although males register significantly more attempts before committing to a final answer than do female students. These results provide insight into effective CT pacing during Peer Instruction. In particular, in order to maintain a pace that keeps everyone engaged, students should not be given too much time to respond. When around 80% of the answers are in, the ratio of correct to incorrect responses rapidly approaches levels indicating random guessing and instructors should close the poll.

Time-Course Analysis of Gene Expression During the Saccharomyces cerevisiae Hypoxic Response

Directory of Open Access Journals (Sweden)

Nasrine Bendjilali

2017-01-01

Full Text Available Many cells experience hypoxia, or low oxygen, and respond by dramatically altering gene expression. In the yeast Saccharomyces cerevisiae, genes that respond are required for many oxygen-dependent cellular processes, such as respiration, biosynthesis, and redox regulation. To more fully characterize the global response to hypoxia, we exposed yeast to hypoxic conditions, extracted RNA at different times, and performed RNA sequencing (RNA-seq analysis. Time-course statistical analysis revealed hundreds of genes that changed expression by up to 550-fold. The genes responded with varying kinetics suggesting that multiple regulatory pathways are involved. We identified most known oxygen-regulated genes and also uncovered new regulated genes. Reverse transcription-quantitative PCR (RT-qPCR analysis confirmed that the lysine methyltransferase EFM6 and the recombinase DMC1, both conserved in humans, are indeed oxygen-responsive. Looking more broadly, oxygen-regulated genes participate in expected processes like respiration and lipid metabolism, but also in unexpected processes like amino acid and vitamin metabolism. Using principle component analysis, we discovered that the hypoxic response largely occurs during the first 2 hr and then a new steady-state expression state is achieved. Moreover, we show that the oxygen-dependent genes are not part of the previously described environmental stress response (ESR consisting of genes that respond to diverse types of stress. While hypoxia appears to cause a transient stress, the hypoxic response is mostly characterized by a transition to a new state of gene expression. In summary, our results reveal that hypoxia causes widespread and complex changes in gene expression to prepare the cell to function with little or no oxygen.

Time-Course Analysis of Gene Expression During the Saccharomyces cerevisiae Hypoxic Response.

Science.gov (United States)

Bendjilali, Nasrine; MacLeon, Samuel; Kalra, Gurmannat; Willis, Stephen D; Hossian, A K M Nawshad; Avery, Erica; Wojtowicz, Olivia; Hickman, Mark J

2017-01-05

Many cells experience hypoxia, or low oxygen, and respond by dramatically altering gene expression. In the yeast Saccharomyces cerevisiae, genes that respond are required for many oxygen-dependent cellular processes, such as respiration, biosynthesis, and redox regulation. To more fully characterize the global response to hypoxia, we exposed yeast to hypoxic conditions, extracted RNA at different times, and performed RNA sequencing (RNA-seq) analysis. Time-course statistical analysis revealed hundreds of genes that changed expression by up to 550-fold. The genes responded with varying kinetics suggesting that multiple regulatory pathways are involved. We identified most known oxygen-regulated genes and also uncovered new regulated genes. Reverse transcription-quantitative PCR (RT-qPCR) analysis confirmed that the lysine methyltransferase EFM6 and the recombinase DMC1, both conserved in humans, are indeed oxygen-responsive. Looking more broadly, oxygen-regulated genes participate in expected processes like respiration and lipid metabolism, but also in unexpected processes like amino acid and vitamin metabolism. Using principle component analysis, we discovered that the hypoxic response largely occurs during the first 2 hr and then a new steady-state expression state is achieved. Moreover, we show that the oxygen-dependent genes are not part of the previously described environmental stress response (ESR) consisting of genes that respond to diverse types of stress. While hypoxia appears to cause a transient stress, the hypoxic response is mostly characterized by a transition to a new state of gene expression. In summary, our results reveal that hypoxia causes widespread and complex changes in gene expression to prepare the cell to function with little or no oxygen. Copyright © 2017 Bendjilali et al.

A time-domain method to generate artificial time history from a given reference response spectrum

Energy Technology Data Exchange (ETDEWEB)

Shin, Gang Sik [Korea Institute of Nuclear Safety, Daejeon (Korea, Republic of); Song, Oh Seop [Dept. of Mechanical Engineering, Chungnam National University, Daejeon (Korea, Republic of)

2016-06-15

Seismic qualification by test is widely used as a way to show the integrity and functionality of equipment that is related to the overall safety of nuclear power plants. Another means of seismic qualification is by direct integration analysis. Both approaches require a series of time histories as an input. However, in most cases, the possibility of using real earthquake data is limited. Thus, artificial time histories are widely used instead. In many cases, however, response spectra are given. Thus, most of the artificial time histories are generated from the given response spectra. Obtaining the response spectrum from a given time history is straightforward. However, the procedure for generating artificial time histories from a given response spectrum is difficult and complex to understand. Thus, this paper presents a simple time-domain method for generating a time history from a given response spectrum; the method was shown to satisfy conditions derived from nuclear regulatory guidance.

A time-domain method to generate artificial time history from a given reference response spectrum

International Nuclear Information System (INIS)

Shin, Gang Sik; Song, Oh Seop

2016-01-01

Seismic qualification by test is widely used as a way to show the integrity and functionality of equipment that is related to the overall safety of nuclear power plants. Another means of seismic qualification is by direct integration analysis. Both approaches require a series of time histories as an input. However, in most cases, the possibility of using real earthquake data is limited. Thus, artificial time histories are widely used instead. In many cases, however, response spectra are given. Thus, most of the artificial time histories are generated from the given response spectra. Obtaining the response spectrum from a given time history is straightforward. However, the procedure for generating artificial time histories from a given response spectrum is difficult and complex to understand. Thus, this paper presents a simple time-domain method for generating a time history from a given response spectrum; the method was shown to satisfy conditions derived from nuclear regulatory guidance

A new time-space accounting scheme to predict stream water residence time and hydrograph source components at the watershed scale

Science.gov (United States)

Takahiro Sayama; Jeffrey J. McDonnell

2009-01-01

Hydrograph source components and stream water residence time are fundamental behavioral descriptors of watersheds but, as yet, are poorly represented in most rainfall-runoff models. We present a new time-space accounting scheme (T-SAS) to simulate the pre-event and event water fractions, mean residence time, and spatial source of streamflow at the watershed scale. We...

Use of Response Time for Measuring Cognitive Ability

Directory of Open Access Journals (Sweden)

Patrick C. Kyllonen

2016-11-01

Full Text Available The purpose of this paper is to review some of the key literature on response time as it has played a role in cognitive ability measurement, providing a historical perspective as well as covering current research. We discuss the speed-level distinction, dimensions of speed and level in cognitive abilities frameworks, speed–accuracy tradeoff, approaches to addressing speed–accuracy tradeoff, analysis methods, particularly item response theory-based, response time models from cognitive psychology (ex-Gaussian function, and the diffusion model, and other uses of response time in testing besides ability measurement. We discuss several new methods that can be used to provide greater insight into the speed and level aspects of cognitive ability and speed–accuracy tradeoff decisions. These include item-level time limits, the use of feedback (e.g., CUSUMs, explicit scoring rules that combine speed and accuracy information (e.g., count down timing, and cognitive psychology models. We also review some of the key psychometric advances in modeling speed and level, which combine speed and ability measurement, address speed–accuracy tradeoff, allow for distinctions between response times on items responded to correctly and incorrectly, and integrate psychometrics with information-processing modeling. We suggest that the application of these models and tools is likely to advance both the science and measurement of human abilities for theory and applications.

A heteroscedastic generalized linear model with a non-normal speed factor for responses and response times.

Science.gov (United States)

Molenaar, Dylan; Bolsinova, Maria

2017-05-01

In generalized linear modelling of responses and response times, the observed response time variables are commonly transformed to make their distribution approximately normal. A normal distribution for the transformed response times is desirable as it justifies the linearity and homoscedasticity assumptions in the underlying linear model. Past research has, however, shown that the transformed response times are not always normal. Models have been developed to accommodate this violation. In the present study, we propose a modelling approach for responses and response times to test and model non-normality in the transformed response times. Most importantly, we distinguish between non-normality due to heteroscedastic residual variances, and non-normality due to a skewed speed factor. In a simulation study, we establish parameter recovery and the power to separate both effects. In addition, we apply the model to a real data set. © 2017 The Authors. British Journal of Mathematical and Statistical Psychology published by John Wiley & Sons Ltd on behalf of British Psychological Society.

Time response of temperature sensors using neural networks

International Nuclear Information System (INIS)

Santos, Roberto Carlos dos

2010-01-01

In a PWR nuclear power plant, the primary coolant temperature and feedwater temperature are measured using RTDs (Resistance Temperature Detectors). These RTDs typically feed the plant's control and safety systems and must, therefore, be very accurate and have good dynamic performance. The response time of RTDs is characterized by a single parameter called the Plunge Time Constant defined as the time it takes the sensor output to achieve 63.2 percent of its final value after a step change in temperature. Nuclear reactor service conditions are difficult to reproduce in the laboratory, and an in-situ test method called LCSR (Loop Current Step Response) test was developed to measure remotely the response time of RTDs. >From this test, the time constant of the sensor is identified by means of the LCSR transformation that involves the dynamic response modal time constants determination using a nodal heat-transfer model. This calculation is not simple and requires specialized personnel. For this reason an Artificial Neural Network has been developed to predict the time constant of RTD from LCSR test transient. It eliminates the transformations involved in the LCSR application. A series of LCSR tests on RTDs generates the response transients of the sensors, the input data of the networks. Plunge tests are used to determine the time constants of the RTDs, the desired output of the ANN, trained using these sets of input/output data. This methodology was firstly applied to theoretical data simulating 10 RTDs with different time constant values, resulting in an average error of about 0.74 %. Experimental data from three different RTDs was used to predict time constant resulting in a maximum error of 3,34 %. The time constants values predicted from ANN were compared with those obtained from traditional way resulting in an average error of about 18 % and that shows the network is able to predict accurately the sensor time constant. (author)

Latent semantics as cognitive components

DEFF Research Database (Denmark)

Petersen, Michael Kai; Mørup, Morten; Hansen, Lars Kai

2010-01-01

Cognitive component analysis, defined as an unsupervised learning of features resembling human comprehension, suggests that the sensory structures we perceive might often be modeled by reducing dimensionality and treating objects in space and time as linear mixtures incorporating sparsity...... emotional responses can be encoded in words, we propose a simplified cognitive approach to model how we perceive media. Representing song lyrics in a vector space of reduced dimensionality using LSA, we combine bottom-up defined term distances with affective adjectives, that top-down constrain the latent......, which we suggest might function as cognitive components for perceiving the underlying structure in lyrics....

Investigations on response time of magnetorheological elastomer under compression mode

Science.gov (United States)

Zhu, Mi; Yu, Miao; Qi, Song; Fu, Jie

2018-05-01

For efficient fast control of vibration system with magnetorheological elastomer (MRE)-based smart device, the response time of MRE material is the key parameter which directly affects the control performance of the vibration system. For a step coil current excitation, this paper proposed a Maxwell behavior model with time constant λ to describe the normal force response of MRE, and the response time of MRE was extracted through the separation of coil response time. Besides, the transient responses of MRE under compression mode were experimentally investigated, and the effects of (i) applied current, (ii) particle distribution and (iii) compressive strain on the response time of MRE were addressed. The results revealed that the three factors can affect the response characteristic of MRE quite significantly. Besides the intrinsic importance for contributing to the response evaluation and effective design of MRE device, this study may conduce to the optimal design of controller for MRE control system.

Cognitive Reflection, Decision Biases, and Response Times

Directory of Open Access Journals (Sweden)

Carlos Alos-Ferrer

2016-09-01

Full Text Available We present novel evidence on decision times and personality traits in standard questions from the decision-making literature where responses are relatively slow (medians around half a minute or above. To this end, we measured decision times in a number of incentivized, framed items (decisions from description including the Cognitive Reflection Test, two additional questions following the same logic, and a number of classic questions used to study decision biases in probability judgments (base-rate neglect, the conjunction fallacy, and the ratio bias. All questions create a conflict between an intuitive process and more deliberative thinking. For each item, we then created a non-conflict version by either making the intuitive impulse correct (resulting in an alignment question, shutting it down (creating a neutral question, or making it dominant (creating a heuristic question. For CRT questions, the differences in decision times are as predicted by dual-process theories, with alignment and heuristic variants leading to faster responses and neutral questions to slower responses than the original, conflict questions. For decision biases (where responses are slower, evidence is mixed. To explore the possible influence of personality factors on both choices and decision times, we used standard personality scales including the Rational-Experiential Inventory and the Big Five, and used the mas controls in regression analysis.

Timing criteria for supplemental BWR emergency response equipment

International Nuclear Information System (INIS)

Bickel, John H.

2015-01-01

The Great Tohuku Earthquake and subsequent Tsunami represented a double failure event which destroyed offsite power connections to Fukushima-Daiichi site and then destroyed on-site electrical systems needed to run decay heat removal systems. The accident could have been mitigated had there been supplemental portable battery chargers, supplemental pumps, and in-place piping connections to provide alternate decay heat removal. In response to this event in the USA, two national response centers, one in Memphis, Tennessee, and another in Phoenix, Arizona, will begin operation. They will be able to dispatch supplemental emergency response equipment to any nuclear plant in the U.S. within 24 hours. In order to define requirements for supplemental nuclear power plant emergency response equipment maintained onsite vs. in a regional support center it is necessary to confirm: (a) the earliest time such equipment might be needed depending on the specific scenario, (b) the nominal time to move the equipment from a storage location either on-site or within the region of a nuclear power plant, and (c) the time required to connect in the supplemental equipment to use it. This paper describes an evaluation process for a BWR-4 with a Mark I Containment starting with: (a) severe accident simulation to define best estimate times available for recovery based on the specific scenario, (b) identify the key supplemental response equipment needed at specific times to accomplish recovery of key safety functions, and (c) evaluate what types of equipment should be warehoused on-site vs. in regional response centers. (authors)

Heat flux estimation for neutral beam line components using inverse heat conduction procedures

International Nuclear Information System (INIS)

Bharathi, P.; Prahlad, V.; Quereshi, K.; Bansal, L.K.; Rambabu, S.; Sharma, S.K.; Parmar, S.; Patel, P.J.; Baruah, U.K.; Patel, Ravi

2015-01-01

In this work, we describe and compare the analytical IHCP methods such-as semi-infinite method, finite slab method and a numerical method called Stolz method for estimating the incident heat flux from the experimentally measured temperature data. In case of analytical methods, the finite time response of the sensor is needed to be accounted for an accurate power density estimations. The modified models corrected for the response time of the sensors are also discussed in this paper. Application of these methods using example temperature waveforms obtained on the SST1-NBI test stand is presented and discussed. For choosing the suitable method for the calorimetry on beam line components, the estimated results are also validated using the ANSYS analysis done on these beam Iine components. As a conclusion, the finite slab method corrected for the influence of the sensor response time found out to be the most suitable method for the inversion of temperature data in case of neutral beam line components

FREQUENCY COMPONENT EXTRACTION OF HEARTBEAT CUES WITH SHORT TIME FOURIER TRANSFORM (STFT

Directory of Open Access Journals (Sweden)

Sumarna Sumarna

2017-01-01

  Electro-acoustic human heartbeat detector have been made with the main parts : (a stetoscope (piece chest, (b mic condenser, (c transistor amplifier, and (d cues analysis program with MATLAB. The frequency components that contained in heartbeat. cues have also been extracted with Short Time Fourier Transform (STFT from 9 volunteers. The results of the analysis showed that heart rate appeared in every cue frequency spectrum with their harmony. The steps of the research were including detector instrument design, test and instrument repair, cues heartbeat recording with Sound Forge 10 program and stored in wav file ; cues breaking at the start and the end, and extraction/cues analysis using MATLAB. The MATLAB program included filter (bandpass filter with bandwidth between 0.01 – 110 Hz, cues breaking with hamming window and every part was calculated using Fourier Transform (STFT mechanism and the result were shown in frequency spectrum graph.   Keywords: frequency components extraction, heartbeat cues, Short Time Fourier Transform

Other components

International Nuclear Information System (INIS)

Anon.

1993-01-01

This chapter includes descriptions of electronic and mechanical components which do not merit a chapter to themselves. Other hardware requires mention because of particularly high tolerance or intolerance of exposure to radiation. A more systematic analysis of radiation responses of structures which are definable by material was given in section 3.8. The components discussed here are field effect transistors, transducers, temperature sensors, magnetic components, superconductors, mechanical sensors, and miscellaneous electronic components

Specific IgE response to different grass pollen allergen components in children undergoing sublingual immunotherapy

Directory of Open Access Journals (Sweden)

Marcucci Francesco

2012-06-01

Full Text Available Abstract Background Grass pollen is a major cause of respiratory allergy worldwide and contain a number of allergens, some of theme (Phl p 1, Phl p 2, Phl p 5, and Phl 6 from Phleum pratense, and their homologous in other grasses are known as major allergens. The administration of grass pollen extracts by immunotherapy generally induces an initial rise in specific immunoglobulin E (sIgE production followed by a progressive decline during the treatment. Some studies reported that immunotherapy is able to induce a de novo sensitisation to allergen component previously unrecognized. Methods We investigated in 30 children (19 males and 11 females, mean age 11.3 years, 19 treated with sublingual immunotherapy (SLIT by a 5-grass extract and 11 untreated, the sIgE and sIgG4 response to the different allergen components. Results Significant increases (p  Conclusions These findings confirm that the initial phase of SLIT with a grass pollen extract enhances the sIgE synthesis and show that the sIgE response concerns the same allergen components which induce IgE reactivity during natural exposure.

Validation of a simple response-time measure of listening effort

NARCIS (Netherlands)

Pals, Carina; Sarampalis, Anastasios; van Rijn, Hedderik; Başkent, Deniz

This study compares two response-time measures of listening effort that can be combined with a clinical speech test for a more comprehensive evaluation of total listening experience; verbal response times to auditory stimuli (RTaud) and response times to a visual task (RTsvis) in a dual- task

Verification of the local structural response of building structures in the anchorage areas of heavy components

International Nuclear Information System (INIS)

Krutzik, N.J.; Tropp, R.

1993-01-01

In both nuclear and non-nuclear areas of power plants, sections of structures, parts of systems and components are attached to walls and floors by means of anchor plates with bolts, anchor sleeves and bolts and through bolts arranged either in groups or individually. In order to simplify the determination of the transfered vibrations induced by external events (e.g. earthquake, aircraft crash), it is normally assumed that the nodal point between component and concrete possesses rigid body characteristics and the building structure (walls, floors) is also inflexible in the anchorage area. In the course of the parametric studies performed, the nonlinear effects on the anchorage area of a component (in this case an anchor plate and concrete slab) were calculated and the effect of these on the actual vibration behavior and the local structural responses of the building structure at the place of installation of heavy components were investigated. The investigations performed reveal that by taking into account the local behaviour in the anchoring point, it is possible to reduce the dynamic response considerably. More detailed examination of the influence of additional parameters (especially of the geometry of the anchor plates and anchor bolts and their material characteristics) will require further investigations aimed at establishing the characteristics of typical anchor plates. (orig.)

Response-related potentials during semantic priming: the effect of a speeded button response task on ERPs.

Directory of Open Access Journals (Sweden)

Marijn van Vliet

Full Text Available This study examines the influence of a button response task on the event-related potential (ERP in a semantic priming experiment. Of particular interest is the N400 component. In many semantic priming studies, subjects are asked to respond to a stimulus as fast and accurately as possible by pressing a button. Response time (RT is recorded in parallel with an electroencephalogram (EEG for ERP analysis. In this case, the response occurs in the time window used for ERP analysis and response-related components may overlap with stimulus-locked ones such as the N400. This has led to a recommendation against such a design, although the issue has not been explored in depth. Since studies keep being published that disregard this issue, a more detailed examination of influence of response-related potentials on the ERP is needed. Two experiments were performed in which subjects pressed one of two buttons with their dominant hand in response to word-pairs with varying association strength (AS, indicating a personal judgement of association between the two words. In the first experiment, subjects were instructed to respond as fast and accurately as possible. In the second experiment, subjects delayed their button response to enforce a one second interval between the onset of the target word and the button response. Results show that in the first experiment a P3 component and motor-related potentials (MRPs overlap with the N400 component, which can cause a misinterpretation of the latter. In order to study the N400 component, the button response should be delayed to avoid contamination of the ERP with response-related components.

Prefrontal cortex activity is associated with biobehavioral components of the stress response

Directory of Open Access Journals (Sweden)

Muriah D Wheelock

2016-11-01

Full Text Available Contemporary theory suggests that prefrontal cortex (PFC function is associated with individual variability in the psychobiology of the stress response. Advancing our understanding of this complex biobehavioral pathway has potential to provide insight into processes that determine individual differences in stress susceptibility. The present study used functional magnetic resonance imaging (fMRI to examine brain activity during a variation of the Montreal Imaging Stress Task (MIST in fifty-three young adults. Salivary cortisol was assessed as an index of the stress response, trait anxiety was assessed as an index of an individual’s disposition towards negative affectivity, and self-reported stress was assessed as an index of an individual’s subjective psychological experience. Heart rate and skin conductance responses were also assessed as additional measures of physiological reactivity. Dorsomedial PFC, dorsolateral PFC, and inferior parietal lobule demonstrated differential activity during the MIST. Further, differences in salivary cortisol reactivity to the MIST were associated with ventromedial PFC and posterior cingulate activity, while trait anxiety and self-reported stress were associated with dorsomedial and ventromedial PFC activity respectively. These findings underscore that PFC activity regulates behavioral and psychobiological components of the stress response.

Time dependent unavailability analysis of nuclear safety systems considering periodically tested components

International Nuclear Information System (INIS)

Goes, Alexandre Gromann de Araujo

1988-01-01

It is of utmost importance to have a computer code in order to analyze how different parameters (like test duration time) affect the unavailability of safety systems of nuclear. In this context, a study was performed in order to evaluate the model employed by the FRANTIC computer code, which performs detailed calculations on the contribution to the system unavailability originated by hardware failures, component tests and repairs, aiming at considering the influence of different test schemes on the system unavailability. It was shown, by means of the results attained that the numerical model used by the FRANTIC code and the analytical model proposed by APOSTOLAKIS and CHU (4) give unavailability values much similar when the component tests are supposed to be perfect. When a test is supposed to be imperfect (that is, when it may induce a test is supposed to be imperfect (that is, when it may induce a failure on the component being tested), the analytical model presents more conservative results. (author)

A Study of Improving Response Time Verification Method for Pressure Transmitters

International Nuclear Information System (INIS)

Lee, Jungyang; Ha, Jaehong; Jung, Insoo; Jo, Junghee; Kim, Hangbae

2007-01-01

Technical Specifications (TS) of OPR1000 type nuclear power plants in Korea require pressure sensor response time testing (RTT) to ensure sensor performance per assumption in plant safety analyses. However, the need for pressure sensor response time testing is not clear because the nominal sensor response times are in the order of milliseconds while overall loop response time limits being from several seconds to tens of seconds. Additionally, response time testing does not appear to identify response time degradation or failures. Consequently, the need for this testing has been questioned, and a study to determine if response time testing is necessary to justify the assumptions in plant safety analyses in the United States has been conducted and NRC has approved to remove the test requirements for them. A similar study was conducted for OPR1000 type nuclear power plants and the results are presented here

Real-Time Decision Making and Aggressive Behavior in Youth: A Heuristic Model of Response Evaluation and Decision (RED).

Science.gov (United States)

Fontaine, Reid Griffith; Dodge, Kenneth A

2006-11-01

Considerable scientific and intervention attention has been paid to judgment and decision-making systems associated with aggressive behavior in youth. However, most empirical studies have investigated social-cognitive correlates of stable child and adolescent aggressiveness, and less is known about real-time decision making to engage in aggressive behavior. A model of real-time decision making must incorporate both impulsive actions and rational thought. The present paper advances a process model (response evaluation and decision; RED) of real-time behavioral judgments and decision making in aggressive youths with mathematic representations that may be used to quantify response strength. These components are a heuristic to describe decision making, though it is doubtful that individuals always mentally complete these steps. RED represents an organization of social-cognitive operations believed to be active during the response decision step of social information processing. The model posits that RED processes can be circumvented through impulsive responding. This article provides a description and integration of thoughtful, rational decision making and nonrational impulsivity in aggressive behavioral interactions.

Decreasing Transition Times in Elementary School Classrooms: Using Computer-Assisted Instruction to Automate Intervention Components

Science.gov (United States)

Hine, Jeffrey F.; Ardoin, Scott P.; Foster, Tori E.

2015-01-01

Research suggests that students spend a substantial amount of time transitioning between classroom activities, which may reduce time spent academically engaged. This study used an ABAB design to evaluate the effects of a computer-assisted intervention that automated intervention components previously shown to decrease transition times. We examined…

A Recurrent Probabilistic Neural Network with Dimensionality Reduction Based on Time-series Discriminant Component Analysis.

Science.gov (United States)

Hayashi, Hideaki; Shibanoki, Taro; Shima, Keisuke; Kurita, Yuichi; Tsuji, Toshio

2015-12-01

This paper proposes a probabilistic neural network (NN) developed on the basis of time-series discriminant component analysis (TSDCA) that can be used to classify high-dimensional time-series patterns. TSDCA involves the compression of high-dimensional time series into a lower dimensional space using a set of orthogonal transformations and the calculation of posterior probabilities based on a continuous-density hidden Markov model with a Gaussian mixture model expressed in the reduced-dimensional space. The analysis can be incorporated into an NN, which is named a time-series discriminant component network (TSDCN), so that parameters of dimensionality reduction and classification can be obtained simultaneously as network coefficients according to a backpropagation through time-based learning algorithm with the Lagrange multiplier method. The TSDCN is considered to enable high-accuracy classification of high-dimensional time-series patterns and to reduce the computation time taken for network training. The validity of the TSDCN is demonstrated for high-dimensional artificial data and electroencephalogram signals in the experiments conducted during the study.

Developing a complex independent component analysis technique to extract non-stationary patterns from geophysical time-series

Science.gov (United States)

Forootan, Ehsan; Kusche, Jürgen

2016-04-01

Geodetic/geophysical observations, such as the time series of global terrestrial water storage change or sea level and temperature change, represent samples of physical processes and therefore contain information about complex physical interactionswith many inherent time scales. Extracting relevant information from these samples, for example quantifying the seasonality of a physical process or its variability due to large-scale ocean-atmosphere interactions, is not possible by rendering simple time series approaches. In the last decades, decomposition techniques have found increasing interest for extracting patterns from geophysical observations. Traditionally, principal component analysis (PCA) and more recently independent component analysis (ICA) are common techniques to extract statistical orthogonal (uncorrelated) and independent modes that represent the maximum variance of observations, respectively. PCA and ICA can be classified as stationary signal decomposition techniques since they are based on decomposing the auto-covariance matrix or diagonalizing higher (than two)-order statistical tensors from centered time series. However, the stationary assumption is obviously not justifiable for many geophysical and climate variables even after removing cyclic components e.g., the seasonal cycles. In this paper, we present a new decomposition method, the complex independent component analysis (CICA, Forootan, PhD-2014), which can be applied to extract to non-stationary (changing in space and time) patterns from geophysical time series. Here, CICA is derived as an extension of real-valued ICA (Forootan and Kusche, JoG-2012), where we (i) define a new complex data set using a Hilbert transformation. The complex time series contain the observed values in their real part, and the temporal rate of variability in their imaginary part. (ii) An ICA algorithm based on diagonalization of fourth-order cumulants is then applied to decompose the new complex data set in (i

IAEA consultants' meeting on thermal response of plasma facing materials and components

International Nuclear Information System (INIS)

Janev, R.K.

1990-07-01

The present Summary Report contains brief proceedings and the main conclusions and recommendations of the IAEA Consultants' Meeting on ''Thermal Response of Plasma Facing Materials and Components'', which was organized by the IAEA Atomic and Molecular Data Unit and held on June 11-13, 1990, in Vienna, Austria. The Report also includes a categorization and assessment of currently studied plasma facing materials, a classification scheme of material properties data, required in fusion reactor design, and a survey of the urgently needed material properties data. (author)

Peripheral visual response time and visual display layout

Science.gov (United States)

Haines, R. F.

1974-01-01

Experiments were performed on a group of 42 subjects in a study of their peripheral visual response time to visual signals under positive acceleration, during prolonged bedrest, at passive 70 deg headup body lift, under exposures to high air temperatures and high luminance levels, and under normal stress-free laboratory conditions. Diagrams are plotted for mean response times to white, red, yellow, green, and blue stimuli under different conditions.

What Time Is Sunrise? Revisiting the Refraction Component of Sunrise/set Prediction Models

Science.gov (United States)

Wilson, Teresa; Bartlett, Jennifer L.; Hilton, James Lindsay

2017-01-01

Algorithms that predict sunrise and sunset times currently have an error of one to four minutes at mid-latitudes (0° - 55° N/S) due to limitations in the atmospheric models they incorporate. At higher latitudes, slight changes in refraction can cause significant discrepancies, even including difficulties determining when the Sun appears to rise or set. While different components of refraction are known, how they affect predictions of sunrise/set has not yet been quantified. A better understanding of the contributions from temperature profile, pressure, humidity, and aerosols could significantly improve the standard prediction. We present a sunrise/set calculator that interchanges the refraction component by varying the refraction model. We then compare these predictions with data sets of observed rise/set times to create a better model. Sunrise/set times and meteorological data from multiple locations will be necessary for a thorough investigation of the problem. While there are a few data sets available, we will also begin collecting this data using smartphones as part of a citizen science project. The mobile application for this project will be available in the Google Play store. Data analysis will lead to more complete models that will provide more accurate rise/set times for the benefit of astronomers, navigators, and outdoorsmen everywhere.

Single- versus dual-process models of lexical decision performance: insights from response time distributional analysis.

Science.gov (United States)

Yap, Melvin J; Balota, David A; Cortese, Michael J; Watson, Jason M

2006-12-01

This article evaluates 2 competing models that address the decision-making processes mediating word recognition and lexical decision performance: a hybrid 2-stage model of lexical decision performance and a random-walk model. In 2 experiments, nonword type and word frequency were manipulated across 2 contrasts (pseudohomophone-legal nonword and legal-illegal nonword). When nonwords became more wordlike (i.e., BRNTA vs. BRANT vs. BRANE), response latencies to nonwords were slowed and the word frequency effect increased. More important, distributional analyses revealed that the Nonword Type = Word Frequency interaction was modulated by different components of the response time distribution, depending on the specific nonword contrast. A single-process random-walk model was able to account for this particular set of findings more successfully than the hybrid 2-stage model. (c) 2006 APA, all rights reserved.

Genetic Components of Root Architecture Remodeling in Response to Salt Stress

KAUST Repository

Julkowska, Magdalena; Koevoets, Iko Tamar; Mol, Selena; Hoefsloot, Huub CJ; Feron, Richard; Tester, Mark A.; Keurentjes, Joost J.B.; Korte, Arthur; Haring, Michel A; de Boer, Gert-Jan; Testerink, Christa

2017-01-01

Salinity of the soil is highly detrimental to plant growth. Plants respond by a redistribution of root mass between main and lateral roots, yet the genetic machinery underlying this process is still largely unknown. Here, we describe the natural variation among 347 Arabidopsis thaliana accessions in root system architecture (RSA) and identify the traits with highest natural variation in their response to salt. Salt-induced changes in RSA were associated with 100 genetic loci using genome-wide association studies (GWAS). Two candidate loci associated with lateral root development were validated and further investigated. Changes in CYP79B2 expression in salt stress positively correlated with lateral root development in accessions, and cyp79b2 cyp79b3 double mutants developed fewer and shorter lateral roots under salt stress, but not in control conditions. By contrast, high HKT1 expression in the root repressed lateral root development, which could be partially rescued by addition of potassium. The collected data and Multi-Variate analysis of multiple RSA traits, available through the Salt_NV_Root App, capture root responses to salinity. Together, our results provide a better understanding of effective RSA remodeling responses, and the genetic components involved, for plant performance in stress conditions.

Genetic Components of Root Architecture Remodeling in Response to Salt Stress

KAUST Repository

Julkowska, Magdalena

2017-11-07

Salinity of the soil is highly detrimental to plant growth. Plants respond by a redistribution of root mass between main and lateral roots, yet the genetic machinery underlying this process is still largely unknown. Here, we describe the natural variation among 347 Arabidopsis thaliana accessions in root system architecture (RSA) and identify the traits with highest natural variation in their response to salt. Salt-induced changes in RSA were associated with 100 genetic loci using genome-wide association studies (GWAS). Two candidate loci associated with lateral root development were validated and further investigated. Changes in CYP79B2 expression in salt stress positively correlated with lateral root development in accessions, and cyp79b2 cyp79b3 double mutants developed fewer and shorter lateral roots under salt stress, but not in control conditions. By contrast, high HKT1 expression in the root repressed lateral root development, which could be partially rescued by addition of potassium. The collected data and Multi-Variate analysis of multiple RSA traits, available through the Salt_NV_Root App, capture root responses to salinity. Together, our results provide a better understanding of effective RSA remodeling responses, and the genetic components involved, for plant performance in stress conditions.

Identification by irradiation, in vitro, of two components of erythroprotein action

International Nuclear Information System (INIS)

Barcos, M.

1978-01-01

The effect of ionizing radiation on the response of normal cultured rat marrow cells to erythropoietin yielded two-component inactivation curves for induced iron uptake and hemoglobin synthesis. The radioresistant component of the induced hemoglobin response (1) was detected earlier, at 6 to 20 hr after irradiation, (2) had a DO 0 > or = to 900 R, (3) gave a nonlinear erythropoietin dose--response plot at 600 R, (4) disappeared when marrow from erythremic rats was used, and (5) showed maximal inactivation by 500 R when irradiation preceded hormone addition by 1.5 to 2.5 hr. The radiosensitive component (1) was observed without any contribution from the radioresistant component when the time of assay of normal marrow was postponed from 6 to 20 hr to 20 to 44 hr of culture, (2) had a D 0 = 63 R, (3) gave linear erythropoietin dose--response curves at 15 to 60 R, and (4) showed enhanced inhibition by 60 R if irradiation either preceded or followed hormone addition by 3 hr or more

Time-Frequency Data Reduction for Event Related Potentials: Combining Principal Component Analysis and Matching Pursuit

Directory of Open Access Journals (Sweden)

Selin Aviyente

2010-01-01

Full Text Available Joint time-frequency representations offer a rich representation of event related potentials (ERPs that cannot be obtained through individual time or frequency domain analysis. This representation, however, comes at the expense of increased data volume and the difficulty of interpreting the resulting representations. Therefore, methods that can reduce the large amount of time-frequency data to experimentally relevant components are essential. In this paper, we present a method that reduces the large volume of ERP time-frequency data into a few significant time-frequency parameters. The proposed method is based on applying the widely used matching pursuit (MP approach, with a Gabor dictionary, to principal components extracted from the time-frequency domain. The proposed PCA-Gabor decomposition is compared with other time-frequency data reduction methods such as the time-frequency PCA approach alone and standard matching pursuit methods using a Gabor dictionary for both simulated and biological data. The results show that the proposed PCA-Gabor approach performs better than either the PCA alone or the standard MP data reduction methods, by using the smallest amount of ERP data variance to produce the strongest statistical separation between experimental conditions.

The auditory-evoked N2 and P3 components in the stop-signal task: indices of inhibition, response-conflict or error-detection?

Science.gov (United States)

Dimoska, Aneta; Johnstone, Stuart J; Barry, Robert J

2006-11-01

The N2 and P3 components have been separately associated with response inhibition in the stop-signal task, and more recently, the N2 has been implicated in the detection of response-conflict. To isolate response inhibition activity from early sensory processing, the present study compared processing of the stop-signal with that of a task-irrelevant tone, which subjects were instructed to ignore. Stop-signals elicited a larger N2 on failed-stop trials and a larger P3 on successful-stop trials, relative to ignore-signal trials, likely reflecting activity related to failed and successful stopping, respectively. ERPs between fast and slow reaction-time (RT) groups were also examined as it was hypothesised that greater inhibitory activation to stop faster responses would manifest in the component reflecting this process. Successful-stop P3 showed the anticipated effect (globally larger amplitude in the fast than slow RT group), supporting its association with the stopping of an ongoing response. In contrast, N2 was larger in the slow than fast RT group, and in contrast to the predictions of the response-conflict hypothesis, successful-stop N2 and the response-locked error-negativity (Ne) differed in scalp distribution. These findings indicate that the successful-stop N2 may be better explained as a deliberate form of response control or selection, which the slow RT group employed as a means of increasing the likelihood of a successful-stop. Finally, a comparison of stimulus and response-locked ERPs revealed that the failed-stop N2 and P3 appeared to reflect error-related activity, best observed in the response-locked Ne and error-positivity (Pe). Together these findings indicate that the successful-stop N2 and P3 reflect functionally distinct aspects of response control that are dependent upon performance strategies, while failed-stop N2 and P3 reflect error-related activity.

Calibration of the time response functions of a quenched plastic scintillator for neutron time of flight

CERN Document Server

Chen, J B; Peng, H S; Tang, C H; Zhang, B H; Ding, Y K; Chen, M; Chen, H S; Li, C G; Wen, T S; Yu, R Z

2002-01-01

The time response functions of an ultrafast quenched plastic scintillation detector used to measure neutron time of flight spectra were calibrated by utilizing cosmic rays and implosion neutrons from DT-filled capsules at the Shenguang II laser facility. These sources could be regarded as delta function pulses due to their much narrower time widths than those of the time response functions of the detection system. The results showed that the detector responses to DT neutrons and to cosmic rays were 1.18 and 0.96 ns FWHM, respectively.

A Bivariate Generalized Linear Item Response Theory Modeling Framework to the Analysis of Responses and Response Times.

Science.gov (United States)

Molenaar, Dylan; Tuerlinckx, Francis; van der Maas, Han L J

2015-01-01

A generalized linear modeling framework to the analysis of responses and response times is outlined. In this framework, referred to as bivariate generalized linear item response theory (B-GLIRT), separate generalized linear measurement models are specified for the responses and the response times that are subsequently linked by cross-relations. The cross-relations can take various forms. Here, we focus on cross-relations with a linear or interaction term for ability tests, and cross-relations with a curvilinear term for personality tests. In addition, we discuss how popular existing models from the psychometric literature are special cases in the B-GLIRT framework depending on restrictions in the cross-relation. This allows us to compare existing models conceptually and empirically. We discuss various extensions of the traditional models motivated by practical problems. We also illustrate the applicability of our approach using various real data examples, including data on personality and cognitive ability.

Risk-based assessment of the allowable outage times for the unit 1 leningrad nuclear power plant ECCS components

International Nuclear Information System (INIS)

Koukhar, Sergey; Vinnikov, Bronislav

2009-01-01

Present paper describes a method for risk - informed assessment of the Allowable Outage Times (AOTs). The AOT is the time, when components of a safety system allowed to be out of service during power operation or during shutdown operation off a plant. If the components are not restored during the time, the plant in operation must be shut down or the plant in a given shutdown mode has to go to safer shutdown mode. Application of the method is also provided for the equipment of the Unit 1 Leningrad NPP ECCS components. For solution of the problem it is necessary to carry out two series of computations using a Living PSA model, level 1. In the first series of the computations the core damage frequency (CDFb) for the base configuration of the plant is determined (there is no equipment out of service). Here the symbol 'b' means the base configuration of a plant. In the second series of the computations the core damage frequency (CDFi) for the configuration of the plant with the component (which is out of service) is calculated. That is here CDFi is determined for the failure probability of the component equal to 1.0 (component 'i' is unavailable). Then it is necessary to determine so called Risk Increase Factor (RIF) using the following ratio: RIFi = CDFi / CDFb. At last the AOT is calculated with the help of the ratio: AOTi = Tppr / RIFi, where Tppr is a period of time between two Planned Preventive Repairs (PPRs). 1. Using the risk based approach the AOTs were calculated for a set of the components of the Unit 1 Leningrad NPP ECCS components. 2. The main conclusion from the analysis is that the current deterministic AOTs for the ECCS components are conservative and should be extended. 3. The risk based extension of the AOTs for the ECCS components can prevent the Unit 1 Leningrad NPP to enter into the operating modes with increased risk. (author)

On the Relationship Between Transfer Function-derived Response Times and Hydrograph Analysis Timing Parameters: Are there Similarities?

Science.gov (United States)

Bansah, S.; Ali, G.; Haque, M. A.; Tang, V.

2017-12-01

The proportion of precipitation that becomes streamflow is a function of internal catchment characteristics - which include geology, landscape characteristics and vegetation - and influence overall storage dynamics. The timing and quantity of water discharged by a catchment are indeed embedded in event hydrographs. Event hydrograph timing parameters, such as the response lag and time of concentration, are important descriptors of how long it takes the catchment to respond to input precipitation and how long it takes the latter to filter through the catchment. However, the extent to which hydrograph timing parameters relate to average response times derived from fitting transfer functions to annual hydrographs is unknown. In this study, we used a gamma transfer function to determine catchment average response times as well as event-specific hydrograph parameters across a network of eight nested watersheds ranging from 0.19 km2 to 74.6 km2 prairie catchments located in south central Manitoba (Canada). Various statistical analyses were then performed to correlate average response times - estimated using the parameters of the fitted gamma transfer function - to event-specific hydrograph parameters. Preliminary results show significant interannual variations in response times and hydrograph timing parameters: the former were in the order of a few hours to days, while the latter ranged from a few days to weeks. Some statistically significant relationships were detected between response times and event-specific hydrograph parameters. Future analyses will involve the comparison of statistical distributions of event-specific hydrograph parameters with that of runoff response times and baseflow transit times in order to quantity catchment storage dynamics across a range of temporal scales.

Planck 2013 results. VII. HFI time response and beams

CERN Document Server

Ade, P A R; Armitage-Caplan, C; Arnaud, M; Ashdown, M; Atrio-Barandela, F; Aumont, J; Baccigalupi, C; Banday, A J; Barreiro, R B; Battaner, E; Benabed, K; Benoît, A; Benoit-Lévy, A; Bernard, J -P; Bersanelli, M; Bielewicz, P; Bobin, J; Bock, J J; Bond, J R; Borrill, J; Bouchet, F R; Bowyer, J W; Bridges, M; Bucher, M; Burigana, C; Cardoso, J -F; Catalano, A; Challinor, A; Chamballu, A; Chary, R -R; Chiang, L -Y; Chiang, H C; Christensen, P R; Church, S; Clements, D L; Colombi, S; Colombo, L P L; Couchot, F; Coulais, A; Crill, B P; Curto, A; Cuttaia, F; Danese, L; Davies, R D; de Bernardis, P; de Rosa, A; de Zotti, G; Delabrouille, J; Delouis, J -M; Désert, F -X; Diego, J M; Dole, H; Donzelli, S; Doré, O; Douspis, M; Dunkley, J; Dupac, X; Efstathiou, G; Enßlin, T A; Eriksen, H K; Finelli, F; Forni, O; Frailis, M; Fraisse, A A; Franceschi, E; Galeotta, S; Ganga, K; Giard, M; Giraud-Héraud, Y; González-Nuevo, J; Górski, K M; Gratton, S; Gregorio, A; Gruppuso, A; Gudmundsson, J E; Haissinski, J; Hansen, F K; Hanson, D; Harrison, D; Henrot-Versillé, S; Hernández-Monteagudo, C; Herranz, D; Hildebrandt, S R; Hivon, E; Hobson, M; Holmes, W A; Hornstrup, A; Hou, Z; Hovest, W; Huffenberger, K M; Jaffe, T R; Jaffe, A H; Jones, W C; Juvela, M; Keihänen, E; Keskitalo, R; Kisner, T S; Kneissl, R; Knoche, J; Knox, L; Kunz, M; Kurki-Suonio, H; Lagache, G; Lamarre, J -M; Lasenby, A; Laureijs, R J; Lawrence, C R; Leonardi, R; Leroy, C; Lesgourgues, J; Liguori, M; Lilje, P B; Linden-Vørnle, M; López-Caniego, M; Lubin, P M; Macías-Pérez, J F; MacTavish, C J; Maffei, B; Mandolesi, N; Maris, M; Marshall, D J; Martin, P G; Martínez-González, E; Masi, S; Matarrese, S; Matsumura, T; Matthai, F; Mazzotta, P; McGehee, P; Melchiorri, A; Mendes, L; Mennella, A; Migliaccio, M; Mitra, S; Miville-Deschênes, M -A; Moneti, A; Montier, L; Morgante, G; Mortlock, D; Munshi, D; Murphy, J A; Naselsky, P; Nati, F; Natoli, P; Netterfield, C B; Nørgaard-Nielsen, H U; Noviello, F; Novikov, D; Novikov, I; Osborne, S; Oxborrow, C A; Paci, F; Pagano, L; Pajot, F; Paoletti, D; Pasian, F; Patanchon, G; Perdereau, O; Perotto, L; Perrotta, F; Piacentini, F; Piat, M; Pierpaoli, E; Pietrobon, D; Plaszczynski, S; Pointecouteau, E; Polegre, A M; Polenta, G; Ponthieu, N; Popa, L; Poutanen, T; Pratt, G W; Prézeau, G; Prunet, S; Puget, J -L; Rachen, J P; Reinecke, M; Remazeilles, M; Renault, C; Ricciardi, S; Riller, T; Ristorcelli, I; Rocha, G; Rosset, C; Roudier, G; Rowan-Robinson, M; Rusholme, B; Sandri, M; Santos, D; Sauvé, A; Savini, G; Shellard, E P S; Spencer, L D; Starck, J -L; Stolyarov, V; Stompor, R; Sudiwala, R; Sureau, F; Sutton, D; Suur-Uski, A -S; Sygnet, J -F; Tauber, J A; Tavagnacco, D; Terenzi, L; Tomasi, M; Tristram, M; Tucci, M; Umana, G; Valenziano, L; Valiviita, J; Van Tent, B; Vielva, P; Villa, F; Vittorio, N; Wade, L A; Wandelt, B D; Yvon, D; Zacchei, A; Zonca, A

2014-01-01

This paper characterizes the effective beams,the effective beam window functions and the associated errors for the Planck HFI detectors. The effective beam is the angular response including the effect of the optics,detectors,data processing and the scan strategy. The window function is the representation of this beam in the harmonic domain which is required to recover an unbiased measurement of the CMB angular power spectrum. The HFI is a scanning instrument and its effective beams are the convolution of: (a) the optical response of the telescope and feeds;(b)the processing of the time-ordered data and deconvolution of the bolometric and electronic time response; and (c) the merging of several surveys to produce maps. The time response functions are measured using observations of Jupiter and Saturn and by minimizing survey difference residuals. The scanning beam is the post-deconvolution angular response of the instrument, and is characterized with observations of Mars. The main beam solid angles are determin...

A Conserved Two-Component Signal Transduction System Controls the Response to Phosphate Starvation in Bifidobacterium breve UCC2003.

NARCIS (Netherlands)

Alvarez-Martin, P.; Fernandez, M.; O'Connell-Motherway, M.; O'Connell, K.J.; Sauvageot, N.; Fitzgerald, G.F.; Macsharry, J.; Zomer, A.L.; Sinderen, D. van

2012-01-01

This work reports on the identification and molecular characterization of the two-component regulatory system (2CRS) PhoRP, which controls the response to inorganic phosphate (P(i)) starvation in Bifidobacterium breve UCC2003. The response regulator PhoP was shown to bind to the promoter region of

Modeling operators' emergency response time for chemical processing operations.

Science.gov (United States)

Murray, Susan L; Harputlu, Emrah; Mentzer, Ray A; Mannan, M Sam

2014-01-01

Operators have a crucial role during emergencies at a variety of facilities such as chemical processing plants. When an abnormality occurs in the production process, the operator often has limited time to either take corrective actions or evacuate before the situation becomes deadly. It is crucial that system designers and safety professionals can estimate the time required for a response before procedures and facilities are designed and operations are initiated. There are existing industrial engineering techniques to establish time standards for tasks performed at a normal working pace. However, it is reasonable to expect the time required to take action in emergency situations will be different than working at a normal production pace. It is possible that in an emergency, operators will act faster compared to a normal pace. It would be useful for system designers to be able to establish a time range for operators' response times for emergency situations. This article develops a modeling approach to estimate the time standard range for operators taking corrective actions or following evacuation procedures in emergency situations. This will aid engineers and managers in establishing time requirements for operators in emergency situations. The methodology used for this study combines a well-established industrial engineering technique for determining time requirements (predetermined time standard system) and adjustment coefficients for emergency situations developed by the authors. Numerous videos of workers performing well-established tasks at a maximum pace were studied. As an example, one of the tasks analyzed was pit crew workers changing tires as quickly as they could during a race. The operations in these videos were decomposed into basic, fundamental motions (such as walking, reaching for a tool, and bending over) by studying the videos frame by frame. A comparison analysis was then performed between the emergency pace and the normal working pace operations

Real-time protection of in-vessel components in ASDEX Upgrade

International Nuclear Information System (INIS)

Herrmann, A.; Drube, R.; Lunt, T.; Marne, P. de

2011-01-01

A video real time safety system (VRT) for protection of in-vessel components was fully implemented in the machine control system (CODAC) from the 2007 experimental campaign on. The VRT is based on video cameras in contrast to infrared systems. The visible wavelength range has a smaller measurement range but is a factor 5-10 less sensitive against changes of the transmission of the optical system and the target emissivity compared to infrared systems. Up to 12 analog video channels with multiple regions of interest (ROI) are processed and monitored on each video stream. At present two safety algorithms, to detect the fraction of overheating in a ROI and hot spot detection, respectively, are implemented. The integral algorithm is preferentially used for probe or limiter protection, the hot spot algorithm for divertor protection. The VRT system is realized with ReadHawk real time operating system on a multi core Linux computer.

Real-time protection of in-vessel components in ASDEX Upgrade

Energy Technology Data Exchange (ETDEWEB)

Herrmann, A., E-mail: albrecht.herrmann@ipp.mpg.de [Max-Planck-Institut fuer Plasmaphysik, EURATOM Association, D-85748 Garching (Germany); Drube, R.; Lunt, T.; Marne, P. de [Max-Planck-Institut fuer Plasmaphysik, EURATOM Association, D-85748 Garching (Germany)

2011-10-15

A video real time safety system (VRT) for protection of in-vessel components was fully implemented in the machine control system (CODAC) from the 2007 experimental campaign on. The VRT is based on video cameras in contrast to infrared systems. The visible wavelength range has a smaller measurement range but is a factor 5-10 less sensitive against changes of the transmission of the optical system and the target emissivity compared to infrared systems. Up to 12 analog video channels with multiple regions of interest (ROI) are processed and monitored on each video stream. At present two safety algorithms, to detect the fraction of overheating in a ROI and hot spot detection, respectively, are implemented. The integral algorithm is preferentially used for probe or limiter protection, the hot spot algorithm for divertor protection. The VRT system is realized with ReadHawk real time operating system on a multi core Linux computer.

OSCAR2000 : a multi-component 3-dimensional oil spill contingency and response model

International Nuclear Information System (INIS)

Reed, M.; Daling, P.S.; Brakstad, O.G.; Singsaas, I.; Faksness, L.-G.; Hetland, B.; Ekrol, N.

2000-01-01

Researchers at SINTEF in Norway have studied the weathering of surface oil. They developed a realistic model to analyze alternative spill response strategies. The model represented the formation and composition of the water-accommodated fraction (WAF) of oil for both treated and untreated oil spills. As many as 25 components, pseudo-components, or metabolites were allowed for the specification of oil. Calculations effected using OSCAR were verified in great detail on numerous occasions. The model made it possible to determine rather realistically the dissolution, transformation, and toxicology of dispersed oil clouds, as well as evaporation, emulsification, and natural dispersion. OSCAR comprised a data-based oil weathering model, a three-dimensional oil trajectory and chemical fates model, an oil spill combat model, exposure models for birds, marine mammals, fish and ichthyoplankton. 17 refs., 1 tab., 11 figs

Reliability models for a nonrepairable system with heterogeneous components having a phase-type time-to-failure distribution

International Nuclear Information System (INIS)

Kim, Heungseob; Kim, Pansoo

2017-01-01

This research paper presents practical stochastic models for designing and analyzing the time-dependent reliability of nonrepairable systems. The models are formulated for nonrepairable systems with heterogeneous components having phase-type time-to-failure distributions by a structured continuous time Markov chain (CTMC). The versatility of the phase-type distributions enhances the flexibility and practicality of the systems. By virtue of these benefits, studies in reliability engineering can be more advanced than the previous studies. This study attempts to solve a redundancy allocation problem (RAP) by using these new models. The implications of mixing components, redundancy levels, and redundancy strategies are simultaneously considered to maximize the reliability of a system. An imperfect switching case in a standby redundant system is also considered. Furthermore, the experimental results for a well-known RAP benchmark problem are presented to demonstrate the approximating error of the previous reliability function for a standby redundant system and the usefulness of the current research. - Highlights: • Phase-type time-to-failure distribution is used for components. • Reliability model for nonrepairable system is developed using Markov chain. • System is composed of heterogeneous components. • Model provides the real value of standby system reliability not an approximation. • Redundancy allocation problem is used to show usefulness of this model.

The Effect of Police Response Time on Crime Detection

DEFF Research Database (Denmark)

Blanes i Vidal, Jordi; Kirchmaier, Tom

preferred estimate, a 10% increase in response time leads to a 4.6 percentage points decrease in the likelihood of detection. A faster response time also decreases the number of days that it takes for the police to detect a crime, conditional on eventual detection. We find stronger effects for thefts than...

Response times in a two-node queueing network with feedback

NARCIS (Netherlands)

van der Mei, R.D.; Gijsen, B.M.M.; in 't Veld, N.; van den Berg, J.L.

2002-01-01

The study presented in this paper is motivated by the performance analysis of response times in distributed information systems, where transactions are handled by iterative server and database actions. We model system response times as sojourn times in a two-node open queueing network with a

Response times in a two-node queueing network with feedback

NARCIS (Netherlands)

van der Mei, R.D.; Gijsen, B.M.M.; Gijsen, B.M.M.; in 't Veld, N.; van den Berg, Hans Leo

The study presented in this paper is motivated by the performance analysis of response times in distributed information systems, where transactions are handled by iterative server and database actions. We model system response times as sojourn times in a two-node open queueing network with a

Improvement in MFTF data base system response times

International Nuclear Information System (INIS)

Lang, N.C.; Nelson, B.C.

1983-01-01

The Supervisory Control and Diagnostic System for the Mirror Fusion Test Facility (MFTF) has been designed as an event driven system. To this end we have designed a data base notification facility in which a task can request that it be loaded and started whenever an element in the data base is changed beyond some user defined range. Our initial implementation of the notify facility exhibited marginal response times whenever a data base table with a large number of outstanding notifies was written into. In this paper we discuss the sources of the slow response and describe in detail a new structure for the list of notifies which minimizes search time resulting in significantly faster response

Uncertainty analysis of accident notification time and emergency medical service response time in work zone traffic accidents.

Science.gov (United States)

Meng, Qiang; Weng, Jinxian

2013-01-01

Taking into account the uncertainty caused by exogenous factors, the accident notification time (ANT) and emergency medical service (EMS) response time were modeled as 2 random variables following the lognormal distribution. Their mean values and standard deviations were respectively formulated as the functions of environmental variables including crash time, road type, weekend, holiday, light condition, weather, and work zone type. Work zone traffic accident data from the Fatality Analysis Report System between 2002 and 2009 were utilized to determine the distributions of the ANT and the EMS arrival time in the United States. A mixed logistic regression model, taking into account the uncertainty associated with the ANT and the EMS response time, was developed to estimate the risk of death. The results showed that the uncertainty of the ANT was primarily influenced by crash time and road type, whereas the uncertainty of EMS response time is greatly affected by road type, weather, and light conditions. In addition, work zone accidents occurring during a holiday and in poor light conditions were found to be statistically associated with a longer mean ANT and longer EMS response time. The results also show that shortening the ANT was a more effective approach in reducing the risk of death than the EMS response time in work zones. To shorten the ANT and the EMS response time, work zone activities are suggested to be undertaken during non-holidays, during the daytime, and in good weather and light conditions.

GCS component development cycle

Science.gov (United States)

Rodríguez, Jose A.; Macias, Rosa; Molgo, Jordi; Guerra, Dailos; Pi, Marti

2012-09-01

The GTC1 is an optical-infrared 10-meter segmented mirror telescope at the ORM observatory in Canary Islands (Spain). First light was at 13/07/2007 and since them it is in the operation phase. The GTC control system (GCS) is a distributed object & component oriented system based on RT-CORBA8 and it is responsible for the management and operation of the telescope, including its instrumentation. GCS has used the Rational Unified process (RUP9) in its development. RUP is an iterative software development process framework. After analysing (use cases) and designing (UML10) any of GCS subsystems, an initial component description of its interface is obtained and from that information a component specification is written. In order to improve the code productivity, GCS has adopted the code generation to transform this component specification into the skeleton of component classes based on a software framework, called Device Component Framework. Using the GCS development tools, based on javadoc and gcc, in only one step, the component is generated, compiled and deployed to be tested for the first time through our GUI inspector. The main advantages of this approach are the following: It reduces the learning curve of new developers and the development error rate, allows a systematic use of design patterns in the development and software reuse, speeds up the deliverables of the software product and massively increase the timescale, design consistency and design quality, and eliminates the future refactoring process required for the code.

Linear response at the 4-component relativistic density-functional level: application to the frequency-dependent dipole polarizability of Hg, AuH and PtH2

International Nuclear Information System (INIS)

Salek, Pawel; Helgaker, Trygve; Saue, Trond

2005-01-01

We report the implementation and application of linear response density-functional theory (DFT) based on the 4-component relativistic Dirac-Coulomb Hamiltonian. The theory is cast in the language of second quantization and is based on the quasienergy formalism (Floquet theory), replacing the initial state dependence of the Runge-Gross theorem by periodic boundary conditions. Contradictions in causality and symmetry of the time arguments are thereby avoided and the exchange-correlation potential and kernel can be expressed as functional derivatives of the quasienergy. We critically review the derivation of the quasienergy analogues of the Hohenberg-Kohn theorem and the Kohn-Sham formalism and discuss the nature of the quasienergy exchange-correlation functional. Structure is imposed on the response equations in terms of Hermiticity and time-reversal symmetry. It is observed that functionals of spin and current densities, corresponding to time-antisymmetric operators, contribute to frequency-dependent and not static electric properties. Physically, this follows from the fact that only a time-dependent electric field creates a magnetic field. It is furthermore observed that hybrid functionals enhance spin polarization since only exact exchange contributes to anti-Hermitian trial vectors. We apply 4-component relativistic linear response DFT to the calculation of the frequency-dependent polarizability of the isoelectronic series Hg, AuH and PtH 2 . Unlike for the molecules, the effect of electron correlation on the polarizability of the mercury atom is very large, about 25%. We observe a remarkable performance of the local-density approximation (LDA) functional in reproducing the experimental frequency-dependent polarizability of this atom, clearly superior to that of the BLYP and B3LYP functionals. This allows us to extract Cauchy moments (S(-4) = 382.82 and S(-6) = 6090.89 a.u.) that we believe are superior to experiment since we go to higher order in the Cauchy

Distinguishing Fast and Slow Processes in Accuracy - Response Time Data.

Directory of Open Access Journals (Sweden)

Frederik Coomans

Full Text Available We investigate the relation between speed and accuracy within problem solving in its simplest non-trivial form. We consider tests with only two items and code the item responses in two binary variables: one indicating the response accuracy, and one indicating the response speed. Despite being a very basic setup, it enables us to study item pairs stemming from a broad range of domains such as basic arithmetic, first language learning, intelligence-related problems, and chess, with large numbers of observations for every pair of problems under consideration. We carry out a survey over a large number of such item pairs and compare three types of psychometric accuracy-response time models present in the literature: two 'one-process' models, the first of which models accuracy and response time as conditionally independent and the second of which models accuracy and response time as conditionally dependent, and a 'two-process' model which models accuracy contingent on response time. We find that the data clearly violates the restrictions imposed by both one-process models and requires additional complexity which is parsimoniously provided by the two-process model. We supplement our survey with an analysis of the erroneous responses for an example item pair and demonstrate that there are very significant differences between the types of errors in fast and slow responses.

Measuring older adults' sedentary time: reliability, validity, and responsiveness.

Science.gov (United States)

Gardiner, Paul A; Clark, Bronwyn K; Healy, Genevieve N; Eakin, Elizabeth G; Winkler, Elisabeth A H; Owen, Neville

2011-11-01

With evidence that prolonged sitting has deleterious health consequences, decreasing sedentary time is a potentially important preventive health target. High-quality measures, particularly for use with older adults, who are the most sedentary population group, are needed to evaluate the effect of sedentary behavior interventions. We examined the reliability, validity, and responsiveness to change of a self-report sedentary behavior questionnaire that assessed time spent in behaviors common among older adults: watching television, computer use, reading, socializing, transport and hobbies, and a summary measure (total sedentary time). In the context of a sedentary behavior intervention, nonworking older adults (n = 48, age = 73 ± 8 yr (mean ± SD)) completed the questionnaire on three occasions during a 2-wk period (7 d between administrations) and wore an accelerometer (ActiGraph model GT1M) for two periods of 6 d. Test-retest reliability (for the individual items and the summary measure) and validity (self-reported total sedentary time compared with accelerometer-derived sedentary time) were assessed during the 1-wk preintervention period, using Spearman (ρ) correlations and 95% confidence intervals (CI). Responsiveness to change after the intervention was assessed using the responsiveness statistic (RS). Test-retest reliability was excellent for television viewing time (ρ (95% CI) = 0.78 (0.63-0.89)), computer use (ρ (95% CI) = 0.90 (0.83-0.94)), and reading (ρ (95% CI) = 0.77 (0.62-0.86)); acceptable for hobbies (ρ (95% CI) = 0.61 (0.39-0.76)); and poor for socializing and transport (ρ < 0.45). Total sedentary time had acceptable test-retest reliability (ρ (95% CI) = 0.52 (0.27-0.70)) and validity (ρ (95% CI) = 0.30 (0.02-0.54)). Self-report total sedentary time was similarly responsive to change (RS = 0.47) as accelerometer-derived sedentary time (RS = 0.39). The summary measure of total sedentary time has good repeatability and modest validity and is

Hierarchical Bayes Models for Response Time Data

Science.gov (United States)

Craigmile, Peter F.; Peruggia, Mario; Van Zandt, Trisha

2010-01-01

Human response time (RT) data are widely used in experimental psychology to evaluate theories of mental processing. Typically, the data constitute the times taken by a subject to react to a succession of stimuli under varying experimental conditions. Because of the sequential nature of the experiments there are trends (due to learning, fatigue,…

Analysis and Modeling of the Galvanic Skin Response Spontaneous Component in the context of Intelligent Biofeedback Systems Development

Science.gov (United States)

Unakafov, A.

2009-01-01

The paper presents an approach to galvanic skin response (GSR) spontaneous component analysis and modeling. In the study a classification of biofeedback training methods is given, importance of intelligent methods development is shown. The INTENS method, which is perspective for intellectualization, is presented. An important problem of biofeedback training method intellectualization - estimation of the GSR spontaneous component - is solved in the main part of the work. Its main characteristics are described; results of GSR spontaneous component modeling are shown. Results of small research of an optimum material for GSR probes are presented.

[Construction of the Time Management Scale and examination of the influence of time management on psychological stress response].

Science.gov (United States)

Imura, Tomoya; Takamura, Masahiro; Okazaki, Yoshihiro; Tokunaga, Satoko

2016-10-01

We developed a scale to measure time management and assessed its reliability and validity. We then used this scale to examine the impact of time management on psychological stress response. In Study 1-1, we developed the scale and assessed its internal consistency and criterion-related validity. Findings from a factor analysis revealed three elements of time management, “time estimation,” “time utilization,” and “taking each moment as it comes.” In Study 1-2, we assessed the scale’s test-retest reliability. In Study 1-3, we assessed the validity of the constructed scale. The results indicate that the time management scale has good reliability and validity. In Study 2, we performed a covariance structural analysis to verify our model that hypothesized that time management influences perceived control of time and psychological stress response, and perceived control of time influences psychological stress response. The results showed that time estimation increases the perceived control of time, which in turn decreases stress response. However, we also found that taking each moment as it comes reduces perceived control of time, which in turn increases stress response.

Guarantee of remaining life time. Integrity of mechanical components and control of ageing phenomena

International Nuclear Information System (INIS)

Schuler, X.; Herter, K.H.; Koenig, G.

2012-01-01

The life time of safety relevant systems, structures and components (SSC) of Nuclear Power Plants (NPP) is determined by two main principles. First of all the required quality has to be produced during the design and fabrication process. This means that quality has to be produced and can't be improved by excessive inspections (Basis Safety - quality through production principle). The second one is assigned to the initial quality which has to be maintained during operation. This concerns safe operation during the total life time (life time management), safety against ageing phenomena (AM - ageing management) as well as proof of integrity (e.g. break preclusion or avoidance of fracture for SSC with high safety relevance). Initiated by the Fukushima Dai-ichi event in Japan in spring 2011 for German NPP's Long Term Operation (LTO) is out of question. In June 2011 legislation took decision to phase-out from nuclear by 2022. As a fact safe operation shall be guaranteed for the remaining life time. Within this technical framework the ageing management is a key element. Depending on the safety-relevance of the SSC under observation including preventive maintenance various tasks are required in particular to clarify the mechanisms which contribute systemspecifically to the damage of the components and systems and to define their controlling parameters which have to be monitored and checked. Appropriate continuous or discontinuous measures are to be considered in this connection. The approach to ensure a high standard of quality in operation for the remaining life time and the management of the technical and organizational aspects are demonstrated and explained. The basis for ageing management to be applied to NNPs is included in Nuclear Safety Standard 1403 which describes the ageing management procedures. For SSC with high safety relevance a verification analysis for rupture preclusion (proof of integrity, integrity concept) shall be performed (Nuclear Safety Standard 3206

Real-time multi-target ranging based on chaotic polarization laser radars in the drive-response VCSELs.

Science.gov (United States)

Zhong, Dongzhou; Xu, Geliang; Luo, Wei; Xiao, Zhenzhen

2017-09-04

According to the principle of complete chaos synchronization and the theory of Hilbert phase transformation, we propose a novel real-time multi-target ranging scheme by using chaotic polarization laser radar in the drive-response vertical-cavity surface-emitting lasers (VCSELs). In the scheme, to ensure each polarization component (PC) of the master VCSEL (MVCSEL) to be synchronized steadily with that of the slave VCSEL, the output x-PC and y-PC from the MVCSEL in the drive system and those in the response system are modulated by the linear electro-optic effect simultaneously. Under this condition, by simulating the influences of some key parameters of the system on the synchronization quality and the relative errors of the two-target ranging, related operating parameters can be optimized. The x-PC and the y-PC, as two chaotic radar sources, are used to implement the real-time ranging for two targets. It is found that the measured distances of the two targets at arbitrary position exhibit strong real-time stability and only slight jitter. Their resolutions are up to millimeters, and their relative errors are very small and less than 2.7%.

SU-E-T-751: Three-Component Kinetic Model of Tumor Growth and Radiation Response for Stereotactic Radiosurgery

Energy Technology Data Exchange (ETDEWEB)

Watanabe, Y; Dahlman, E; Leder, K; Hui, S [University of Minnesota, Minneapolis, MN (United States)

2015-06-15

Purpose: To develop and study a kinetic model of tumor growth and its response to stereotactic radiosurgery (SRS) by assuming that the cells in irradiated tumor volume were made of three types. Methods: A set of ordinary differential equations (ODEs) were derived for three types of cells and a tumor growth rate. It is assumed that the cells were composed of actively proliferating cells, lethally damaged-dividing cells, and non-dividing cells. We modeled the tumor volume growth with a time-dependent growth rate to simulate the saturation of growth. After SRS, the proliferating cells were permanently damaged and converted to the lethally damaged cells. The amount of damaged cells were estimated by the LQ-model. The damaged cells gradually stopped dividing/proliferating and died with a constant rate. The dead cells were cleared from their original location with a constant rate. The total tumor volume was the sum of the three components. The ODEs were numerically solved with appropriate initial conditions for a given dosage. The proposed model was used to model an animal experiment, for which the temporal change of a rhabdomyosarcoma tumor volume grown in a rat was measured with time resolution sufficient to test the model. Results: To fit the model to the experimental data, the following characteristics were needed with the model parameters. The α-value in the LQ-model was smaller than the commonly used value; furthermore, it decreased with increasing dose. At the same time, the tumor growth rate after SRS had to increase. Conclusions: The new 3-component model of tumor could simulate the experimental data very well. The current study suggested that the radiation sensitivity and the growth rate of the proliferating tumor cells may change after irradiation and it depended on the dosage used for SRS. These preliminary observations must be confirmed by future animal experiments.

Comparison of LMFBR piping response obtained using response spectrum and time history methods

International Nuclear Information System (INIS)

Hulbert, G.M.

1981-04-01

The dynamic response to a seismic event is calculated for a piping system using a response spectrum analysis method and two time history analysis methods. The results from the analytical methods are compared to identify causes for the differences between the sets of analytical results. Comparative methods are also presented which help to gain confidence in the accuracy of the analytical methods in predicting piping system structure response during seismic events

Modeling an Application's Theoretical Minimum and Average Transactional Response Times

Energy Technology Data Exchange (ETDEWEB)

Paiz, Mary Rose [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2015-04-01

The theoretical minimum transactional response time of an application serves as a ba- sis for the expected response time. The lower threshold for the minimum response time represents the minimum amount of time that the application should take to complete a transaction. Knowing the lower threshold is beneficial in detecting anomalies that are re- sults of unsuccessful transactions. On the converse, when an application's response time falls above an upper threshold, there is likely an anomaly in the application that is causing unusual performance issues in the transaction. This report explains how the non-stationary Generalized Extreme Value distribution is used to estimate the lower threshold of an ap- plication's daily minimum transactional response time. It also explains how the seasonal Autoregressive Integrated Moving Average time series model is used to estimate the upper threshold for an application's average transactional response time.

Time-based MRPC detector response simulations for the CBM time-of-flight system

Energy Technology Data Exchange (ETDEWEB)

Simon, Christian; Herrmann, Norbert [Physikalisches Institut und Fakultaet fuer Physik und Astronomie, Ruprecht-Karls-Universitaet Heidelberg (Germany); Collaboration: CBM-Collaboration

2016-07-01

The design goal of the future Compressed Baryonic Matter (CBM) experiment is to measure rare probes of dense strongly interacting matter with an unprecedented accuracy. Target interaction rates of up to 10 MHz need to be processed by the detector. The time-of-flight (TOF) wall of CBM which should provide hadron identification at particle fluxes of up to a few tens of kHz/cm{sup 2} is composed of high-resolution timing multi-gap resistive plate chambers (MRPCs). Due to the self-triggered digitization and readout scheme of CBM comprising online event reconstruction preparatory Monte Carlo (MC) transport and response simulations including the MRPC array need to be carried out in a time-based fashion. While in an event-based simulation mode interference between MC tracks in a detector volume owing to rate effects or electronics dead time is confined to a single event, time-based response simulations need to take into account track pile-up and interference across events. A proposed time-based digitizer class for CBM-TOF within the CbmRoot software framework is presented.

A Box-Cox normal model for response times

NARCIS (Netherlands)

Klein Entink, R.H.; Fox, J.P.; Linden, W.J. van der

2009-01-01

The log-transform has been a convenient choice in response time modelling on test items. However, motivated by a dataset of the Medical College Admission Test where the lognormal model violated the normality assumption, the possibilities of the broader class of Box–Cox transformations for response

Next-Generation Library Catalogs and the Problem of Slow Response Time

Directory of Open Access Journals (Sweden)

Margaret Brown-Sica

2010-12-01

Full Text Available Response time as defined for this study is the time that it takes for all files that constitute a single webpage to travel across the Internet from a Web server to the end user’s browser. In this study, the authors tested response times on queries for identical items in five different library catalogs, one of them a next-generation (NextGen catalog. The authors also discuss acceptable response time and how it may affect the discovery process. They suggest that librarians and vendors should develop standards for acceptable response time and use it in the product selection and development processes.

Experience with RTD response time testing in nuclear power plants

International Nuclear Information System (INIS)

Hashemian, H.M.; Kerlin, T.W.

1985-01-01

The reactor coolant temperatures in pressurized water reactors are measured with platinum resistance temperature detectors (RTDs). The information furnished by these RTDs is used for plant protection as well as control. As a part of the plant protection system, the RTDs must respond to temperature changes in a timely fashion. The RTD response time requirements are different for the various plant types. These requirements are specified in the plant technical specifications in terms of an RTd time constant. The current time constant requirements for nuclear plant RTDs varies from 0.5 seconds to 13.0 seconds depending on the type of the plant. Therefore, different types of RTDs are used in different plants to achieve the required time constants. In addition, in-situ response time tests are periodically performed on protective system RTDs to ensure that the in-service time constants are within acceptable limits as the plant is operating. The periodic testing is important because response time degradation may occur while the RTD ages in the process. Recent response time tests in operating plants revealed unacceptable time constants for several protection system RTDs. As a result, these plants had to be shut down to resolve the problem which in one case was due to improper installation and in another case was because of degradation of a thermal compound used in the thermowell

Overeating at dinner time among Japanese workers: Is overeating related to stress response and late dinner times?

Science.gov (United States)

Suzuki, Akiko; Sakurazawa, Hirofumi; Fujita, Takanori; Akamatsu, Rie

2016-06-01

There are several known risk factors for overeating, including negative feelings and hunger. It was hypothesized that overtime work is associated with stress responses and later dinner times, leading to longer periods of time without eating, and that this, in turn, leads to a strong experience of hunger and consequent overeating at dinner. The aim of this study was to examine relationships among overeating at dinner, stress responses (e.g., fatigue, anxiety, and depression), and dinner times in Japanese male workers. In December 2012, 255 Japanese male workers at a leasing company completed a self-report questionnaire about overeating at dinner, psychological stress responses, physical stress responses, and dinner times. Each worker was sent an email with a link to the questionnaire website, where his answers were collected. Relationships between overeating at dinner and lifestyle issues were investigated using multiple linear regression analysis treating overeating as a dependent variable. Factors related to overeating at dinner included psychological stress response (β = 0.251 p overeating at dinner is related to dinner time in men and to stress responses. Copyright © 2016 Elsevier Ltd. All rights reserved.

The response time distribution in a real-time database with optimistic concurrency control

NARCIS (Netherlands)

Sassen, S.A.E.; Wal, van der J.

1996-01-01

For a real-time shared-memory database with optimistic concurrency control, an approximation for the transaction response time distribution is obtained. The model assumes that transactions arrive at the database according to a Poisson process, that every transaction uses an equal number of

Quantum characteristics of occurrence scattering time in two-component non-ideal plasmas

Energy Technology Data Exchange (ETDEWEB)

Hong, Woo-Pyo [Department of Electronics Engineering, Catholic University of Daegu, Hayang, 712-702 (Korea, Republic of); Jung, Young-Dae, E-mail: ydjung@hanyang.ac.kr [Department of Applied Physics and Department of Bionanotechnology, Hanyang University, Ansan, Kyunggi-Do 15588 (Korea, Republic of); Department of Physics, Applied Physics, and Astronomy, Rensselaer Polytechnic Institute, 110 8th Street, Troy, NY 12180-3590 (United States)

2015-10-30

The quantum diffraction and plasma screening effects on the occurrence time for the collision process are investigated in two-component non-ideal plasmas. The micropotential model taking into account the quantum diffraction and screening with the eikonal analysis is employed to derive the occurrence time as functions of the collision energy, density parameter, Debye length, de Broglie wavelength, and scattering angle. It is shown that the occurrence time for forward scattering directions decreases the tendency of time-advance with increasing scattering angle and de Broglie wavelength. However, it is found that the occurrence time shows the oscillatory time-advance and time-retarded behaviors with increasing scattering angle. It is found that the plasma screening effect enhances the tendency of time-advance on the occurrence time for forward scattering regions. It is also shown the quantum diffraction effect suppresses the occurrence time advance for forward scattering angles. In addition, it is shown that the occurrence time advance decreases with an increase of the collision energy. - Highlights: • The quantum diffraction and screening effects on the occurrence scattering time are investigated in non-ideal plasmas. • It is shown the quantum diffraction effect suppresses the occurrence time advance for forward scattering angles. • It is found that the plasma screening effect enhances the tendency of time-advance on the occurrence time.

Integrated response and transit time distributions of watersheds by combining hydrograph separation and long-term transit time modeling

Directory of Open Access Journals (Sweden)

M. C. Roa-García

2010-08-01

Full Text Available We present a new modeling approach analyzing and predicting the Transit Time Distribution (TTD and the Response Time Distribution (RTD from hourly to annual time scales as two distinct hydrological processes. The model integrates Isotope Hydrograph Separation (IHS and the Instantaneous Unit Hydrograph (IUH approach as a tool to provide a more realistic description of transit and response time of water in catchments. Individual event simulations and parameterizations were combined with long-term baseflow simulation and parameterizations; this provides a comprehensive picture of the catchment response for a long time span for the hydraulic and isotopic processes. The proposed method was tested in three Andean headwater catchments to compare the effects of land use on hydrological response and solute transport. Results show that the characteristics of events and antecedent conditions have a significant influence on TTD and RTD, but in general the RTD of the grassland dominated catchment is concentrated in the shorter time spans and has a higher cumulative TTD, while the forest dominated catchment has a relatively higher response distribution and lower cumulative TTD. The catchment where wetlands concentrate shows a flashier response, but wetlands also appear to prolong transit time.

Effect of bacterial components of mixed culture supernatants of planktonic and biofilm Pseudomonas aeruginosa with commensal Escherichia coli on the neutrophil response in vitro.

Science.gov (United States)

Maslennikova, Irina L; Kuznetsova, Marina V; Nekrasova, Irina V; Shirshev, Sergei V

2017-11-30

Pseudomonas aeruginosa (PA) responsible for acute and chronic infections often forms a well-organized bacterial population with different microbial species including commensal strains of Escherichia coli. Bacterial extracellular components of mixed culture can modulate the influence of bacteria on the neutrophil functions. The objective of this study was to compare the effect of pyocyanin, pyoverdine, LPS, exopolysaccharide of single species and mixed culture supernatants of PA strains and E. coli K12 on microbicidal, secretory activity of human neutrophils in vitro. Bacterial components of E. coli K12 in mixed supernatants with 'biofilm' PA strains (PA ATCC, PA BALG) enhanced short-term microbicidal mechanisms and inhibited neutrophil secretion delayed in time. The influence of 'planktonic' PA (PA 9-3) exometabolites in mixed culture is almost mimicked by E. coli K12 effect on functional neutrophil changes. This investigation may help to understand some of the mechanisms of neutrophil response to mixed infections of different PA with other bacteria species. © FEMS 2017. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Dissecting Low Atmospheric Pressure Stress: Transcriptome Responses to the Components of Hypobaria in Arabidopsis.

Science.gov (United States)

Zhou, Mingqi; Callaham, Jordan B; Reyes, Matthew; Stasiak, Michael; Riva, Alberto; Zupanska, Agata K; Dixon, Mike A; Paul, Anna-Lisa; Ferl, Robert J

2017-01-01

Controlled hypobaria presents biology with an environment that is never encountered in terrestrial ecology, yet the apparent components of hypobaria are stresses typical of terrestrial ecosystems. High altitude, for example, presents terrestrial hypobaria always with hypoxia as a component stress, since the relative partial pressure of O 2 is constant in the atmosphere. Laboratory-controlled hypobaria, however, allows the dissection of pressure effects away from the effects typically associated with altitude, in particular hypoxia, as the partial pressure of O 2 can be varied. In this study, whole transcriptomes of plants grown in ambient (97 kPa/pO 2 = 21 kPa) atmospheric conditions were compared to those of plants transferred to five different atmospheres of varying pressure and oxygen composition for 24 h: 50 kPa/pO 2 = 10 kPa, 25 kPa/pO 2 = 5 kPa, 50 kPa/pO 2 = 21 kPa, 25 kPa/pO 2 = 21 kPa, or 97 kPa/pO 2 = 5 kPa. The plants exposed to these environments were 10 day old Arabidopsis seedlings grown vertically on hydrated nutrient plates. In addition, 5 day old plants were also exposed for 24 h to the 50 kPa and ambient environments to evaluate age-dependent responses. The gene expression profiles from roots and shoots showed that the hypobaric response contained more complex gene regulation than simple hypoxia, and that adding back oxygen to normoxic conditions did not completely alleviate gene expression changes in hypobaric responses.

Aircraft Fault Detection Using Real-Time Frequency Response Estimation

Science.gov (United States)

Grauer, Jared A.

2016-01-01

A real-time method for estimating time-varying aircraft frequency responses from input and output measurements was demonstrated. The Bat-4 subscale airplane was used with NASA Langley Research Center's AirSTAR unmanned aerial flight test facility to conduct flight tests and collect data for dynamic modeling. Orthogonal phase-optimized multisine inputs, summed with pilot stick and pedal inputs, were used to excite the responses. The aircraft was tested in its normal configuration and with emulated failures, which included a stuck left ruddervator and an increased command path latency. No prior knowledge of a dynamic model was used or available for the estimation. The longitudinal short period dynamics were investigated in this work. Time-varying frequency responses and stability margins were tracked well using a 20 second sliding window of data, as compared to a post-flight analysis using output error parameter estimation and a low-order equivalent system model. This method could be used in a real-time fault detection system, or for other applications of dynamic modeling such as real-time verification of stability margins during envelope expansion tests.

The response-time distribution in a real-time database with optimistic concurrency control and constant execution times

NARCIS (Netherlands)

Sassen, S.A.E.; Wal, van der J.

1997-01-01

For a real-time shared-memory database with optimistic concurrency control, an approximation for the transaction response-time distribution is obtained. The model assumes that transactions arrive at the database according to a Poisson process, that every transaction uses an equal number of

The response-time distribution in a real-time database with optimistic concurrency control and exponential execution times

NARCIS (Netherlands)

Sassen, S.A.E.; Wal, van der J.

1997-01-01

For a real-time shared-memory database with optimistic concurrency control, an approximation for the transaction response-time distribution is obtained. The model assumes that transactions arrive at the database according to a Poisson process, that every transaction takes an exponential execution

Search for an optimum time response of spark counters

International Nuclear Information System (INIS)

Devismes, A.; Finck, Ch.; Kress, T.; Gobbi, A.; Eschke, J.; Herrmann, N.; Hildenbrand, K.D.; Koczon, P.; Petrovici, M.

2002-01-01

A spark counter of the type developed by Pestov has been tested with the aim of searching for an optimum time response function, changing voltage, content of noble and quencher gases, pressure and energy-loss. Replacing the usual argon by neon has brought an improvement of the resolution and a significant reduction of tails in the time response function. It has been proven that a counter as long as 90 cm can deliver, using neon gas mixture, a time resolution σ<60 ps with about 1% absolute tail and an efficiency of about 90%

Accurate and efficient calculation of response times for groundwater flow

Science.gov (United States)

Carr, Elliot J.; Simpson, Matthew J.

2018-03-01

We study measures of the amount of time required for transient flow in heterogeneous porous media to effectively reach steady state, also known as the response time. Here, we develop a new approach that extends the concept of mean action time. Previous applications of the theory of mean action time to estimate the response time use the first two central moments of the probability density function associated with the transition from the initial condition, at t = 0, to the steady state condition that arises in the long time limit, as t → ∞ . This previous approach leads to a computationally convenient estimation of the response time, but the accuracy can be poor. Here, we outline a powerful extension using the first k raw moments, showing how to produce an extremely accurate estimate by making use of asymptotic properties of the cumulative distribution function. Results are validated using an existing laboratory-scale data set describing flow in a homogeneous porous medium. In addition, we demonstrate how the results also apply to flow in heterogeneous porous media. Overall, the new method is: (i) extremely accurate; and (ii) computationally inexpensive. In fact, the computational cost of the new method is orders of magnitude less than the computational effort required to study the response time by solving the transient flow equation. Furthermore, the approach provides a rigorous mathematical connection with the heuristic argument that the response time for flow in a homogeneous porous medium is proportional to L2 / D , where L is a relevant length scale, and D is the aquifer diffusivity. Here, we extend such heuristic arguments by providing a clear mathematical definition of the proportionality constant.

A Unique Fungal Two-Component System Regulates Stress Responses, Drug Sensitivity, Sexual Development, and Virulence of Cryptococcus neoformans

Science.gov (United States)

Bahn, Yong-Sun; Kojima, Kaihei; Cox, Gary M.

2006-01-01

The stress-activated mitogen-activated protein kinase (MAPK) pathway is widely used by eukaryotic organisms as a central conduit via which cellular responses to the environment effect growth and differentiation. The basidiomycetous human fungal pathogen Cryptococcus neoformans uniquely uses the stress-activated Pbs2-Hog1 MAPK system to govern a plethora of cellular events, including stress responses, drug sensitivity, sexual reproduction, and virulence. Here, we characterized a fungal “two-component” system that controls these fundamental cellular functions via the Pbs2-Hog1 MAPK cascade. A typical response regulator, Ssk1, modulated all Hog1-dependent phenotypes by controlling Hog1 phosphorylation, indicating that Ssk1 is the major upstream signaling component of the Pbs2-Hog1 pathway. A second response regulator, Skn7, governs sensitivity to Na+ ions and the antifungal agent fludioxonil, negatively controls melanin production, and functions independently of Hog1 regulation. To control these response regulators, C. neoformans uses multiple sensor kinases, including two-component–like (Tco) 1 and Tco2. Tco1 and Tco2 play shared and distinct roles in stress responses and drug sensitivity through the Hog1 MAPK system. Furthermore, each sensor kinase mediates unique cellular functions for virulence and morphological differentiation. Our findings highlight unique adaptations of this global two-component MAPK signaling cascade in a ubiquitous human fungal pathogen. PMID:16672377

Kiwifruit Non-Sugar Components Reduce Glycaemic Response to Co-Ingested Cereal in Humans

Directory of Open Access Journals (Sweden)

Suman Mishra

2017-10-01

Full Text Available Kiwifruit (KF effects on the human glycaemic response to co-ingested wheat cereal were determined. Participants (n = 20 consumed four meals in random order, all being made to 40 g of the same available carbohydrate, by adding kiwifruit sugars (KF sug; glucose, fructose, sucrose 2:2:1 to meals not containing KF. The meals were flaked wheat biscuit (WB+KFsug, WB+KF, WB+guar gum+KFsug, WB+guar gum+KF, that was ingested after fasting overnight. Blood glucose was monitored 3 h and hunger measured at 180 min post-meal using a visual analogue scale. KF and guar reduced postprandial blood glucose response amplitude, and prevented subsequent hypoglycaemia that occurred with WB+KFsug. The area between the blood glucose response curve and baseline from 0 to 180 min was not significantly different between meals, 0–120 min areas were significantly reduced by KF and/or guar. Area from 120 to 180 min was positive for KF, guar, and KF+guar, while the area for the WB meal was negative. Hunger at 180 min was significantly reduced by KF and/or guar when compared with WB. We conclude that KF components other than available carbohydrate may improve the glycaemic response profile to co-ingested cereal food.

Congestion Service Facilities Location Problem with Promise of Response Time

Directory of Open Access Journals (Sweden)

Dandan Hu

2013-01-01

Full Text Available In many services, promise of specific response time is advertised as a commitment by the service providers for the customer satisfaction. Congestion on service facilities could delay the delivery of the services and hurts the overall satisfaction. In this paper, congestion service facilities location problem with promise of response time is studied, and a mixed integer nonlinear programming model is presented with budget constrained. The facilities are modeled as M/M/c queues. The decision variables of the model are the locations of the service facilities and the number of servers at each facility. The objective function is to maximize the demands served within specific response time promised by the service provider. To solve this problem, we propose an algorithm that combines greedy and genetic algorithms. In order to verify the proposed algorithm, a lot of computational experiments are tested. And the results demonstrate that response time has a significant impact on location decision.

Elucidation of time-dependent systems biology cell response patterns with time course network enrichment

DEFF Research Database (Denmark)

Wiwie, Christian; Rauch, Alexander; Haakonsson, Anders

2018-01-01

, no methods exist to integrate time series data with networks, thus preventing the identification of time-dependent systems biology responses. We close this gap with Time Course Network Enrichment (TiCoNE). It combines a new kind of human-augmented clustering with a novel approach to network enrichment...

Decreased reaction time variability is associated with greater cardiovascular responses to acute stress.

Science.gov (United States)

Wawrzyniak, Andrew J; Hamer, Mark; Steptoe, Andrew; Endrighi, Romano

2016-05-01

Cardiovascular (CV) responses to mental stress are prospectively associated with poor CV outcomes. The association between CV responses to mental stress and reaction times (RTs) in aging individuals may be important but warrants further investigation. The present study assessed RTs to examine associations with CV responses to mental stress in healthy, older individuals using robust regression techniques. Participants were 262 men and women (mean age = 63.3 ± 5.5 years) from the Whitehall II cohort who completed a RT task (Stroop) and underwent acute mental stress (mirror tracing) to elicit CV responses. Blood pressure, heart rate, and heart rate variability were measured at baseline, during acute stress, and through a 75-min recovery. RT measures were generated from an ex-Gaussian distribution that yielded three predictors: mu-RT, sigma-RT, and tau-RT, the mean, standard deviation, and mean of the exponential component of the normal distribution, respectively. Decreased intraindividual RT variability was marginally associated with greater systolic (B = -.009, SE = .005, p = .09) and diastolic (B = -.004, SE = .002, p = .08) blood pressure reactivity. Decreased intraindividual RT variability was associated with impaired systolic blood pressure recovery (B = -.007, SE = .003, p = .03) and impaired vagal tone (B = -.0047, SE = .0024, p = .045). Study findings offer tentative support for an association between RTs and CV responses. Despite small effect sizes and associations not consistent across predictors, these data may point to a link between intrinsic neuronal plasticity and CV responses. © 2016 The Authors. Psychophysiology published by Wiley Periodicals, Inc. on behalf of Society for Psychophysiological Research.

Study on the time-domain electromagnetic responses; TDEM ho ni okeru denji oto ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Noguchi, K; Endo, M [Waseda University, Tokyo (Japan). School of Science and Engineering

1997-05-27

With an objective to perform three-dimensional analysis with high accuracy in using the electromagnetic exploration method, characteristics in electromagnetic response were analyzed, and conditions for acquiring necessary data were discussed. The discussion defined a parameter called `response anomaly` which uses response from media to standardize response only from substances with abnormal resistivity. The receivers were located uniformly on the same plane, and the response anomaly was derived from electromagnetic response from each of the three horizontal and vertical components at each receiving point, which was expressed as a contour map. The parameter for the abnormal body was consisted of location and resistivity contrast with media. Discussions using the contour map were given on the response when these factors for the parameter were varied. As a result, it was found that the response anomaly appears in the form that reflects the abnormal body, and the response anomaly of the horizontal component is superior in terms of being large. It was also referred that, as a requirement for the abnormal body which gives larger impact from the electromagnetic response, the abnormal body should have lower resistivity than that in the media, and resistivity contrast with the media should be greater. 2 refs., 7 figs., 1 tab.

The Importance of Responsibility in Times of Crisis

OpenAIRE

Jacob Dahl Rendtorff

2014-01-01

In this paper I would like to show the importance of the concept of responsibility as the foundation of ethics in times of crisis in particular in the fields of politics and economics in the modern civilisation marked by globalization and technological progres. I consider the concept of responsibility as the key notion in order to understand the ethical duty in a modern technological civilisation. We can indeed observe a moralization of the concept of responsibility going beyond a strict lega...

Temporal evolution of photon energy emitted from two-component advective flows: origin of time lag

Science.gov (United States)

Chatterjee, Arka; Chakrabarti, Sandip K.; Ghosh, Himadri

2017-12-01

X-ray time lag of black hole candidates contains important information regarding the emission geometry. Recently, study of time lags from observational data revealed very intriguing properties. To investigate the real cause of this lag behavior with energy and spectral states, we study photon paths inside a two-component advective flow (TCAF) which appears to be a satisfactory model to explain the spectral and timing properties. We employ the Monte Carlo simulation technique to carry out the Comptonization process. We use a relativistic thick disk in Schwarzschild geometry as the CENtrifugal pressure supported BOundary Layer (CENBOL) which is the Compton cloud. In TCAF, this is the post-shock region of the advective component. Keplerian disk on the equatorial plane which is truncated at the inner edge i.e. at the outer boundary of the CENBOL, acts as the soft photon source. Ray-tracing code is employed to track the photons to a distantly located observer. We compute the cumulative time taken by a photon during Comptonization, reflection and following the curved geometry on the way to the observer. Time lags between various hard and soft bands have been calculated. We study the variation of time lags with accretion rates, CENBOL size and inclination angle. Time lags for different energy channels are plotted for different inclination angles. The general trend of variation of time lag with QPO frequency and energy as observed in satellite data is reproduced.

Time course based artifact identification for independent components of resting state fMRI

Directory of Open Access Journals (Sweden)

Christian eRummel

2013-05-01

Full Text Available In functional magnetic resonance imaging (fMRI coherent oscillations of the blood oxygen level dependent (BOLD signal can be detected. These arise when brain regions respond to external stimuli or are activated by tasks. The same networks have been characterized during wakeful rest when functional connectivity of the human brain is organized in generic resting state networks (RSN. Alterations of RSN emerge as neurobiological markers of pathological conditions such as altered mental state. In single-subject fMRI data the coherent components can be identified by blind source separation of the pre-processed BOLD data using spatial independent component analysis (ICA and related approaches. The resulting maps may represent physiological RSNs or may be due to various artifacts. In this methodological study, we propose a conceptually simple and fully automatic time course based filtering procedure to detect obvious artifacts in the ICA output for resting state fMRI. The filter is trained on six and tested on 29 healthy subjects, yielding mean filter accuracy, sensitivity and specificity of 0.80, 0.82 and 0.75 in out-of-sample tests. To estimate the impact of clearly artifactual single-subject components on group resting state studies we analyze unfiltered and filtered output with a second level ICA procedure. Although the automated filter does not reach performance values of visual analysis by human raters, we propose that resting state compatible analysis of ICA time courses could be very useful to complement the existing map or task/event oriented artifact classification algorithms.

Transformation Algorithm of Dielectric Response in Time-Frequency Domain

Directory of Open Access Journals (Sweden)

Ji Liu

2014-01-01

Full Text Available A transformation algorithm of dielectric response from time domain to frequency domain is presented. In order to shorten measuring time of low or ultralow frequency dielectric response characteristics, the transformation algorithm is used in this paper to transform the time domain relaxation current to frequency domain current for calculating the low frequency dielectric dissipation factor. In addition, it is shown from comparing the calculation results with actual test data that there is a coincidence for both results over a wide range of low frequencies. Meanwhile, the time domain test data of depolarization currents in dry and moist pressboards are converted into frequency domain results on the basis of the transformation. The frequency domain curves of complex capacitance and dielectric dissipation factor at the low frequency range are obtained. Test results of polarization and depolarization current (PDC in pressboards are also given at the different voltage and polarization time. It is demonstrated from the experimental results that polarization and depolarization current are affected significantly by moisture contents of the test pressboards, and the transformation algorithm is effective in ultralow frequency of 10−3 Hz. Data analysis and interpretation of the test results conclude that analysis of time-frequency domain dielectric response can be used for assessing insulation system in power transformer.

Modeling Mental Speed: Decomposing Response Time Distributions in Elementary Cognitive Tasks and Correlations with Working Memory Capacity and Fluid Intelligence

Directory of Open Access Journals (Sweden)

Florian Schmitz

2016-10-01

Full Text Available Previous research has shown an inverse relation between response times in elementary cognitive tasks and intelligence, but findings are inconsistent as to which is the most informative score. We conducted a study (N = 200 using a battery of elementary cognitive tasks, working memory capacity (WMC paradigms, and a test of fluid intelligence (gf. Frequently used candidate scores and model parameters derived from the response time (RT distribution were tested. Results confirmed a clear correlation of mean RT with WMC and to a lesser degree with gf. Highly comparable correlations were obtained for alternative location measures with or without extreme value treatment. Moderate correlations were found as well for scores of RT variability, but they were not as strong as for mean RT. Additionally, there was a trend towards higher correlations for slow RT bands, as compared to faster RT bands. Clearer evidence was obtained in an ex-Gaussian decomposition of the response times: the exponential component was selectively related to WMC and gf in easy tasks, while mean response time was additionally predictive in the most complex tasks. The diffusion model parsimoniously accounted for these effects in terms of individual differences in drift rate. Finally, correlations of model parameters as trait-like dispositions were investigated across different tasks, by correlating parameters of the diffusion and the ex-Gaussian model with conventional RT and accuracy scores.

Application of Real-Time Automated Traffic Incident Response Plan Management System: A Web Structure for the Regional Highway Network in China

Directory of Open Access Journals (Sweden)

Yongfeng Ma

2014-01-01

Full Text Available Traffic incidents, caused by various factors, may lead to heavy traffic delay and be harmful to traffic capacity of downstream sections. Traffic incident management (TIM systems have been developed widely to respond to traffic incidents intelligently and reduce the losses. Traffic incident response plans, as an important component of TIM, can effectively guide responders as to what and how to do in traffic incidents. In the paper, a real-time automated traffic incident response plan management system was developed, which could generate and manage traffic incident response plans timely and automatically. A web application structure and a physical structure were designed to implement and show these functions. A standard framework of data storage was also developed to save information about traffic incidents and generated response plans. Furthermore, a conformation survey and case-based reasoning (CBR were introduced to identify traffic incident and generate traffic incident response plans automatically, respectively. Twenty-three traffic crash-related incidents were selected and three indicators were used to measure the system performance. Results showed that 20 of 23 cases could be retrieved effectively and accurately. The system is practicable to generate traffic incident response plans and has been implemented in China.

Auditory evoked responses to binaural beat illusion: stimulus generation and the derivation of the Binaural Interaction Component (BIC).

Science.gov (United States)

Ozdamar, Ozcan; Bohorquez, Jorge; Mihajloski, Todor; Yavuz, Erdem; Lachowska, Magdalena

2011-01-01

Electrophysiological indices of auditory binaural beats illusions are studied using late latency evoked responses. Binaural beats are generated by continuous monaural FM tones with slightly different ascending and descending frequencies lasting about 25 ms presented at 1 sec intervals. Frequency changes are carefully adjusted to avoid any creation of abrupt waveform changes. Binaural Interaction Component (BIC) analysis is used to separate the neural responses due to binaural involvement. The results show that the transient auditory evoked responses can be obtained from the auditory illusion of binaural beats.

Detection of advance item knowledge using response times in computer adaptive testing

NARCIS (Netherlands)

Meijer, R.R.; Sotaridona, Leonardo

2006-01-01

We propose a new method for detecting item preknowledge in a CAT based on an estimate of “effective response time” for each item. Effective response time is defined as the time required for an individual examinee to answer an item correctly. An unusually short response time relative to the expected

Control of ultrafast pulse propagation in semiconductor components

DEFF Research Database (Denmark)

Poel, Mike van der; Hansen, Per Lunnemann; Mørk, Jesper

2009-01-01

Time shifting of optical pulses with duration in the range from 100 fs to a few ps represents one extreme of slow light, where THz bandwidth for the slow down or speed up is necessary. The physics of the time shifting of such very short pulses involves the gain saturation of the optical medium...... and is different from the slow-light mechanisms responsible for time shifting of pulses of narrower bandwidth. Experimental and theoretical results with semiconductor components are presented, emphasizing the physics as well as the limitations imposed by the dynamical processes....

Response probability and response time: a straight line, the Tagging/Retagging interpretation of short term memory, an operational definition of meaningfulness and short term memory time decay and search time.

Science.gov (United States)

Tarnow, Eugen

2008-12-01

The functional relationship between correct response probability and response time is investigated in data sets from Rubin, Hinton and Wenzel, J Exp Psychol Learn Mem Cogn 25:1161-1176, 1999 and Anderson, J Exp Psychol [Hum Learn] 7:326-343, 1981. The two measures are linearly related through stimulus presentation lags from 0 to 594 s in the former experiment and for repeated learning of words in the latter. The Tagging/Retagging interpretation of short term memory is introduced to explain this linear relationship. At stimulus presentation the words are tagged. This tagging level drops slowly with time. When a probe word is reintroduced the tagging level has to increase for the word to be properly identified leading to a delay in response time. The tagging time is related to the meaningfulness of the words used-the more meaningful the word the longer the tagging time. After stimulus presentation the tagging level drops in a logarithmic fashion to 50% after 10 s and to 20% after 240 s. The incorrect recall and recognition times saturate in the Rubin et al. data set (they are not linear for large time lags), suggesting a limited time to search the short term memory structure: the search time for recall of unusual words is 1.7 s. For recognition of nonsense words the corresponding time is about 0.4 s, similar to the 0.243 s found in Cavanagh (1972).

Effectiveness Analysis of a Part-Time Rapid Response System During Operation Versus Nonoperation.

Science.gov (United States)

Kim, Youlim; Lee, Dong Seon; Min, Hyunju; Choi, Yun Young; Lee, Eun Young; Song, Inae; Park, Jong Sun; Cho, Young-Jae; Jo, You Hwan; Yoon, Ho Il; Lee, Jae Ho; Lee, Choon-Taek; Do, Sang Hwan; Lee, Yeon Joo

2017-06-01

To evaluate the effect of a part-time rapid response system on the occurrence rate of cardiopulmonary arrest by comparing the times of rapid response system operation versus nonoperation. Retrospective cohort study. A 1,360-bed tertiary care hospital. Adult patients admitted to the general ward were screened. Data were collected over 36 months from rapid response system implementation (October 2012 to September 2015) and more than 45 months before rapid response system implementation (January 2009 to September 2012). None. The rapid response system operates from 7 AM to 10 PM on weekdays and from 7 AM to 12 PM on Saturdays. Primary outcomes were the difference of cardiopulmonary arrest incidence between pre-rapid response system and post-rapid response system periods and whether the rapid response system operating time affects the cardiopulmonary arrest incidence. The overall cardiopulmonary arrest incidence (per 1,000 admissions) was 1.43. Although the number of admissions per month and case-mix index were increased (3,555.18 vs 4,564.72, p times (0.82 vs 0.49/1,000 admissions; p = 0.001) but remained similar during rapid response system nonoperating times (0.77 vs 0.73/1,000 admissions; p = 0.729). The implementation of a part-time rapid response system reduced the cardiopulmonary arrest incidence based on the reduction of cardiopulmonary arrest during rapid response system operating times. Further analysis of the cost effectiveness of part-time rapid response system is needed.

'Faceness' and affectivity: evidence for genetic contributions to distinct components of electrocortical response to human faces.

Science.gov (United States)

Shannon, Robert W; Patrick, Christopher J; Venables, Noah C; He, Sheng

2013-12-01

The ability to recognize a variety of different human faces is undoubtedly one of the most important and impressive functions of the human perceptual system. Neuroimaging studies have revealed multiple brain regions (including the FFA, STS, OFA) and electrophysiological studies have identified differing brain event-related potential (ERP) components (e.g., N170, P200) possibly related to distinct types of face information processing. To evaluate the heritability of ERP components associated with face processing, including N170, P200, and LPP, we examined ERP responses to fearful and neutral face stimuli in monozygotic (MZ) and dizygotic (DZ) twins. Concordance levels for early brain response indices of face processing (N170, P200) were found to be stronger for MZ than DZ twins, providing evidence of a heritable basis to each. These findings support the idea that certain key neural mechanisms for face processing are genetically coded. Implications for understanding individual differences in recognition of facial identity and the emotional content of faces are discussed. Copyright © 2013 Elsevier Inc. All rights reserved.

Frequency-dependent effects of background noise on subcortical response timing.

Science.gov (United States)

Tierney, A; Parbery-Clark, A; Skoe, E; Kraus, N

2011-12-01

The addition of background noise to an auditory signal delays brainstem response timing. This effect has been extensively documented using manual peak selection. Peak picking, however, is impractical for large-scale studies of spectrotemporally complex stimuli, and leaves open the question of whether noise-induced delays are frequency-dependent or occur across the frequency spectrum. Here we use an automated, objective method to examine phase shifts between auditory brainstem responses to a speech sound (/da/) presented with and without background noise. We predicted that shifts in neural response timing would also be reflected in frequency-specific phase shifts. Our results indicate that the addition of background noise causes phase shifts across the subcortical response spectrum (70-1000 Hz). However, this noise-induced delay is not uniform such that some frequency bands show greater shifts than others: low-frequency phase shifts (300-500 Hz) are largest during the response to the consonant-vowel formant transition (/d/), while high-frequency shifts (720-1000 Hz) predominate during the response to the steady-state vowel (/a/). Most importantly, phase shifts occurring in specific frequency bands correlate strongly with shifts in the latencies of the predominant peaks in the auditory brainstem response, while phase shifts in other frequency bands do not. This finding confirms the validity of phase shift detection as an objective measure of timing differences and reveals that this method detects noise-induced shifts in timing that may not be captured by traditional peak latency measurements. Copyright © 2011 Elsevier B.V. All rights reserved.

Pengenalan Wajah Pada Sistem Presensi Menggunakan Metode Dynamic Times Wrapping, Principal Component Analysis dan Gabor Wavelet

Directory of Open Access Journals (Sweden)

Romi Wiryadinata

2016-03-01

Full Text Available Presensi is a logging attendance, part of activity reporting an institution, or a component institution itself which contains the presence data compiled and arranged so that it is easy to search for and used when required at any time by the parties concerned. Computer application developed in the presensi system is a computer application that can recognize a person's face using only a webcam. Face recognition in this study using a webcam to capture an image of the room at any given time who later identified the existing faces. Some of the methods used in the research here is a method of the Dynamic Times Wrapping (DTW, Principal Component Analysis (PCA and Gabor Wavelet. This system, used in testing with normal facial image expression. The success rate of the introduction with the normal expression of face image using DTW amounting to 80%, 100% and PCA Gabor wavelet 97%

Can Previewing Sport-Specific Video Influence Reactive-Agility Response Time?

Science.gov (United States)

Holding, Ryan; Meir, Rudi; Zhou, Shi

2017-02-01

The purpose of this study was to examine whether a video-based warm-up could provide an acute performance benefit to response time for athletes in a sport-specific agility task. In addition, 2 learning strategies, explicit and implicit, were compared for their effectiveness in facilitating an improvement in sport-specific agility. Thirty representative male junior rugby union players (age 14-16 y, mean age 14.6 ± 1.09 y) were placed in 3 experimental groups (explicit, implicit, and control) and completed 2 intervention sessions. Testing sessions included preintervention testing, completion of the video-based warm-up intervention, and postintervention testing. A 3D motion-analysis system was used to assess response time in the testing battery. The athletes' response times on the pre- to postintervention tests were compared to determine the effectiveness of the video-based warm-up. A 2-way general linear model with repeated-measures analysis indicated that both the explicit (P = .030, d = 0.28) and implicit (P = .049, d = 0.33) groups significantly improved their response time by the intervention compared with the control group (P = .367, d = 0.08). The mean postintervention response time for the explicit group improved by 19.1% (from 0.246 s pre to 0.199 s post), and the implicit group improved by 15.7% (from 0.268 s to 0.226 s). Findings suggest that a video-based warm-up may provide an acute benefit to sport-specific agility performance for junior athletes.

Excited-state absorption in tetrapyridyl porphyrins: comparing real-time and quadratic-response time-dependent density functional theory

Energy Technology Data Exchange (ETDEWEB)

Bowman, David N. [Department of Chemistry; Supercomputing Institute and Chemical Theory Center; University of Minnesota; Minneapolis; USA; Asher, Jason C. [Department of Chemistry; Supercomputing Institute and Chemical Theory Center; University of Minnesota; Minneapolis; USA; Fischer, Sean A. [William R. Wiley Environmental Molecular Sciences Laboratory; Pacific Northwest National Laboratory; P.O. Box 999; Richland; USA; Cramer, Christopher J. [Department of Chemistry; Supercomputing Institute and Chemical Theory Center; University of Minnesota; Minneapolis; USA; Govind, Niranjan [William R. Wiley Environmental Molecular Sciences Laboratory; Pacific Northwest National Laboratory; P.O. Box 999; Richland; USA

2017-01-01

Threemeso-substituted tetrapyridyl porphyrins (free base, Ni(ii), and Cu(ii)) were investigated for their optical limiting (OL) capabilities using real-time (RT-), linear-response (LR-), and quadratic-response (QR-) time-dependent density functional theory (TDDFT) methods.

A comparison of two procedures for verbal response time fractionation

Directory of Open Access Journals (Sweden)

Lotje evan der Linden

2014-10-01

Full Text Available To describe the mental architecture between stimulus and response, cognitive models often divide the stimulus-response (SR interval into stages or modules. Predictions derived from such models are typically tested by focusing on the moment of response emission, through the analysis of response time (RT distributions. To go beyond the single response event, we recently proposed a method to fractionate verbal RTs into two physiologically defined intervals that are assumed to reflect different processing stages. The analysis of the durations of these intervals can be used to study the interaction between cognitive and motor processing during speech production. Our method is inspired by studies on decision making that used manual responses, in which RTs were fractionated into a premotor time (PMT, assumed to reflect cognitive processing, and a motor time (MT, assumed to reflect motor processing. In these studies, surface EMG activity was recorded from participants' response fingers. EMG onsets, reflecting the initiation of a motor response, were used as the point of fractionation. We adapted this method to speech-production research by measuring verbal responses in combination with EMG activity from facial muscles involved in articulation. However, in contrast to button-press tasks, the complex task of producing speech often resulted in multiple EMG bursts within the SR interval. This observation forced us to decide how to operationalize the point of fractionation: as the first EMG burst after stimulus onset (the stimulus-locked approach, or as the EMG burst that is coupled to the vocal response (the response-locked approach. The point of fractionation has direct consequences on how much of the overall task effect is captured by either interval. Therefore, the purpose of the current paper was to compare both onset-detection procedures in order to make an informed decision about which of the two is preferable. We concluded in favour or the response

The absence of later wave components in auditory brainstem responses as an initial manifestation of type 2 Gaucher disease.

Science.gov (United States)

Okubo, Yusuke; Goto, Masahiro; Sakakibara, Hiroshi; Terakawa, Toshiro; Kaneko, Takashi; Miyama, Sahoko

2014-12-01

Type 2 Gaucher disease is the most severe neuronopathic form of Gaucher disease and is characterized by severe neurodegeneration with brainstem involvement and organ failure. Prediction or diagnosis of type 2 Gaucher disease before the development of neurological complications is difficult. A 5-month-old female infant presented with deafness without other neurological abnormalities. Auditory brainstem response analysis revealed the absence of later wave components. Two months later, muscular rigidity became evident, followed by the development of opisthotonus and strabismus. Rapid progression of splenomegaly led to the diagnosis of type 2 Gaucher disease. Abnormal auditory brainstem response findings may already exist before the development of severe brainstem abnormalities such as muscular rigidity and opisthotonus in type 2 Gaucher disease. When patients present with deafness and absent later wave components on auditory brainstem response, type 2 Gaucher disease should be included in the differential diagnosis even in the absence of other neurological abnormalities. Copyright © 2014 Elsevier Inc. All rights reserved.

Particle Markov Chain Monte Carlo Techniques of Unobserved Component Time Series Models Using Ox

DEFF Research Database (Denmark)

Nonejad, Nima

This paper details Particle Markov chain Monte Carlo techniques for analysis of unobserved component time series models using several economic data sets. PMCMC combines the particle filter with the Metropolis-Hastings algorithm. Overall PMCMC provides a very compelling, computationally fast...... and efficient framework for estimation. These advantages are used to for instance estimate stochastic volatility models with leverage effect or with Student-t distributed errors. We also model changing time series characteristics of the US inflation rate by considering a heteroskedastic ARFIMA model where...

Prediction of the time-dependent failure rate for normally operating components taking into account the operational history

International Nuclear Information System (INIS)

Vrbanic, I.; Simic, Z.; Sljivac, D.

2008-01-01

The prediction of the time-dependent failure rate has been studied, taking into account the operational history of a component used in applications such as system modeling in a probabilistic safety analysis in order to evaluate the impact of equipment aging and maintenance strategies on the risk measures considered. We have selected a time-dependent model for the failure rate which is based on the Weibull distribution and the principles of proportional age reduction by equipment overhauls. Estimation of the parameters that determine the failure rate is considered, including the definition of the operational history model and likelihood function for the Bayesian analysis of parameters for normally operating repairable components. The operational history is provided as a time axis with defined times of overhauls and failures. An example for demonstration is described with prediction of the future behavior for seven different operational histories. (orig.)

Real-time and on-site γ-ray radiation response testing system for semiconductor devices and its applications

Energy Technology Data Exchange (ETDEWEB)

Mu, Yifei, E-mail: Y.Mu@student.liverpool.ac.uk [Department of Electrical Engineering and Electronics, University of Liverpool, Liverpool L69 3GJ (United Kingdom); Zhao, Ce Zhou, E-mail: cezhou.zhao@xjtlu.edu.cn [Department of Electrical and Electronic Engineering, Xi’an Jiaotong-Liverpool University, Suzhou 215123 (China); Qi, Yanfei, E-mail: yanfei.qi01@xjtlu.edu.cn [Department of Electrical and Electronic Engineering, Xi’an Jiaotong-Liverpool University, Suzhou 215123 (China); Lam, Sang, E-mail: s.lam@xjtlu.edu.cn [Department of Electrical and Electronic Engineering, Xi’an Jiaotong-Liverpool University, Suzhou 215123 (China); Zhao, Chun, E-mail: garyzhao@ust.hk [Nano and Advanced Materials Institute, Hong Kong University of Science and Technology, Kowloon (Hong Kong); Lu, Qifeng, E-mail: qifeng@liverpool.ac.uk [Department of Electrical Engineering and Electronics, University of Liverpool, Liverpool L69 3GJ (United Kingdom); Cai, Yutao, E-mail: yutao.cai@xjtlu.edu.cn [Department of Electrical and Electronic Engineering, Xi’an Jiaotong-Liverpool University, Suzhou 215123 (China); Mitrovic, Ivona Z., E-mail: ivona@liverpool.ac.uk [Department of Electrical Engineering and Electronics, University of Liverpool, Liverpool L69 3GJ (United Kingdom); Taylor, Stephen, E-mail: s.taylor@liverpool.ac.uk [Department of Electrical Engineering and Electronics, University of Liverpool, Liverpool L69 3GJ (United Kingdom); Chalker, Paul R., E-mail: pchalker@liverpool.ac.uk [Center for Materials and Structures, School of Engineering, University of Liverpool, Liverpool L69 3GH (United Kingdom)

2016-04-01

The construction of a turnkey real-time and on-site radiation response testing system for semiconductor devices is reported. Components of an on-site radiation response probe station, which contains a 1.11 GBq Cs{sup 137} gamma (γ)-ray source, and equipment of a real-time measurement system are described in detail for the construction of the whole system. The real-time measurement system includes a conventional capacitance–voltage (C–V) and stress module, a pulse C–V and stress module, a conventional current–voltage (I–V) and stress module, a pulse I–V and stress module, a DC on-the-fly (OTF) module and a pulse OTF module. Electrical characteristics of MOS capacitors or MOSFET devices are measured by each module integrated in the probe station under continuous γ-ray exposure and the measurement results are presented. The dose rates of different gate dielectrics are calculated by a novel calculation model based on the Cs{sup 137} γ-ray source placed in the probe station. For the sake of operators’ safety, an equivalent dose rate of 70 nSv/h at a given operation distance is indicated by a dose attenuation model in the experimental environment. HfO{sub 2} thin films formed by atomic layer deposition are employed to investigate the radiation response of the high-κ material by using the conventional C–V and pulse C–V modules. The irradiation exposure of the sample is carried out with a dose rate of 0.175 rad/s and ±1 V bias in the radiation response testing system. Analysis of flat-band voltage shifts (ΔV{sub FB}) of the MOS capacitors suggests that the on-site and real-time/pulse measurements detect more serious degradation of the HfO{sub 2} thin films compared with the off-site irradiation and conventional measurement techniques.

Equal-Time and Equal-Space Poisson Brackets of the N -Component Coupled NLS Equation

International Nuclear Information System (INIS)

Zhou Ru-Guang; Li Pei-Yao; Gao Yuan

2017-01-01

Two Poisson brackets for the N-component coupled nonlinear Schrödinger (NLS) equation are derived by using the variantional principle. The first one is called the equal-time Poisson bracket which does not depend on time but only on the space variable. Actually it is just the usual one describing the time evolution of system in the traditional theory of integrable Hamiltonian systems. The second one is equal-space and new. It is shown that the spatial part of Lax pair with respect to the equal-time Poisson bracket and temporal part of Lax pair with respect to the equal-space Poisson bracket share the same r-matrix formulation. These properties are similar to that of the NLS equation. (paper)

Reclaiming Spare Capacity and Improving Aperiodic Response Times in Real-Time Environments

Directory of Open Access Journals (Sweden)

Liu Xue

2011-01-01

Full Text Available Abstract Scheduling recurring task sets that allow some instances of the tasks to be skipped produces holes in the schedule which are nonuniformly distributed. Similarly, when the recurring tasks are not strictly periodic but are sporadic, there is extra processor bandwidth arising because of irregular job arrivals. The additional computation capacity that results from skips or sporadic tasks can be reclaimed to service aperiodic task requests efficiently and quickly. We present techniques for improving the response times of aperiodic tasks by identifying nonuniformly distributed spare capacity—because of skips or sporadic tasks—in the schedule and adding such extra capacity to the capacity queue of a BASH server. These gaps can account for a significant portion of aperiodic capacity, and their reclamation results in considerable improvement to aperiodic response times. We present two schemes: NCLB-CBS, which performs well in periodic real-time environments with firm tasks, and NCLB-CUS, which can be deployed when the basic task set to schedule is sporadic. Evaluation via simulations and implementation suggests that performance improvements for aperiodic tasks can be obtained with limited additional overhead.

Time response measurements of LASL diagnostic detectors

International Nuclear Information System (INIS)

Hocker, L.P.

1970-07-01

The measurement and data analysis techniques developed under the Los Alamos Scientific Laboratory's detector improvement program were used to characterize the time and frequency response of selected LASL Compton, fluor-photodiode (NPD), and fluor-photomultiplier (NPM) diagnostic detectors. Data acquisition procedures and analysis methods presently in use are summarized, and detector time and frequency data obtained using the EG and G/AEC electron linear accelerator fast pulse (approximately 50 psec FWHM) as the incident radiation driving function are presented. (U.S.)

A Novel Choice Procedure of Magnetic Component Values for Phase Shifted Full Bridge Converters with a Variable Dead-Time Control Method

Directory of Open Access Journals (Sweden)

Lei Zhao

2015-09-01

Full Text Available Magnetic components are important parts of the phase shifted full bridge (PSFB converter. During the dead-time of switches located in the same leg, the converter can achieve zero-voltage-switching (ZVS by using the energies stored in magnetic components to discharge or charge the output capacitances of switches. Dead-time is usually calculated under a given set of pre-defined load condition which results in that the available energies are insufficient and ZVS capability is lost at light loads. In this paper, the PSFB converter is controlled by variable dead-time method and thus full advantage can be taken of the energies stored in magnetic components. Considering that dead-time has a great effect on ZVS, the relationship between available energies and magnetic component values is formulated by analyzing the equivalent circuits during dead-time intervals. Magnetic component values are chosen based on such relationship. The proposed choice procedure can make the available energies greater than the required energies for ZVS operation over a wide range of load conditions. Moreover, the burst mode control is adopted in order to reduce the standby power loss. Experimental results coincide with the theoretical analysis. The proposed method is a simple and practical solution to extend the ZVS range.

Nonlinear Stochastic Analysis of Subharmonic Response of a Shallow Cable

DEFF Research Database (Denmark)

Zhou, Q.; Stærdahl, Jesper Winther; Nielsen, Søren R.K.

2007-01-01

and stochastic subharmonic response is demonstrated upon comparison with a more involved model based on a spatial finite difference discretization of the full nonlinear partial differential equations of the cable. Since the stochastic response quantities are obtained by Monte Carlo simulation, which is extremely...... time-consuming for the finite difference model, most of the results are next based on the reduced model. Under harmonical varying support point motions the stable subharmonic motion consists of a harmonically varying component in the equilibrium plane and a large subharmonic out-of-plane component...... subharmonic response component is also present in the static equilibrium plane. Further, the time variation of the envelope process of the narrow-banded chordwise elongation process tends to enhance chaotic behaviour of the subharmonic response, which is detectable via extreme sensitivity on the initial...

Identification and characterization of sigma, a novel component of the Staphylococcus aureus stress and virulence responses.

Directory of Open Access Journals (Sweden)

Lindsey N Shaw

Full Text Available S. aureus is a highly successful pathogen that is speculated to be the most common cause of human disease. The progression of disease in S. aureus is subject to multi-factorial regulation, in response to the environments encountered during growth. This adaptive nature is thought to be central to pathogenesis, and is the result of multiple regulatory mechanisms employed in gene regulation. In this work we describe the existence of a novel S. aureus regulator, an as yet uncharacterized ECF-sigma factor (sigma(S, that appears to be an important component of the stress and pathogenic responses of this organism. Using biochemical approaches we have shown that sigma(S is able to associates with core-RNAP, and initiate transcription from its own coding region. Using a mutant strain we determined that sigma(S is important for S. aureus survival during starvation, extended exposure to elevated growth temperatures, and Triton X-100 induced lysis. Coculture studies reveal that a sigma(S mutant is significantly outcompeted by its parental strain, which is only exacerbated during prolonged growth (7 days, or in the presence of stressor compounds. Interestingly, transcriptional analysis determined that under standard conditions, S. aureus SH1000 does not initiate expression of sigS. Assays performed hourly for 72 h revealed expression in typically background ranges. Analysis of a potential anti-sigma factor, encoded downstream of sigS, revealed it to have no obvious role in the upregulation of sigS expression. Using a murine model of septic arthritis, sigS-mutant infected animals lost significantly less weight, developed septic arthritis at significantly lower levels, and had increased survival rates. Studies of mounted immune responses reveal that sigS-mutant infected animals had significantly lower levels of IL-6, indicating only a weak immunological response. Finally, strains of S. aureus lacking sigS were far less able to undergo systemic dissemination

How does a collision warning system shape driver's brake response time? The influence of expectancy and automation complacency on real-life emergency braking.

Science.gov (United States)

Ruscio, Daniele; Ciceri, Maria Rita; Biassoni, Federica

2015-04-01

Brake Reaction Time (BRT) is an important parameter for road safety. Previous research has shown that drivers' expectations can impact RT when facing hazardous situations, but driving with advanced driver assistance systems, can change the way BRT are considered. The interaction with a collision warning system can help faster more efficient responses, but at the same time can require a monitoring task and evaluation process that may lead to automation complacency. The aims of the present study are to test in a real-life setting whether automation compliancy can be generated by a collision warning system and what component of expectancy can impact the different tasks involved in an assisted BRT process. More specifically four component of expectancy were investigated: presence/absence of anticipatory information, previous direct experience, reliability of the device, and predictability of the hazard determined by repeated use of the warning system. Results supply indication on perception time and mental elaboration of the collision warning system alerts. In particular reliable warning quickened the decision making process, misleading warnings generated automation complacency slowing visual search for hazard detection, lack of directed experienced slowed the overall response while unexpected failure of the device lead to inattentional blindness and potential pseudo-accidents with surprise obstacle intrusion. Copyright © 2015 Elsevier Ltd. All rights reserved.

Correlated components of ongoing EEG point to emotionally laden attention - a possible marker of engagement?

Science.gov (United States)

Dmochowski, Jacek P; Sajda, Paul; Dias, Joao; Parra, Lucas C

2012-01-01

Recent evidence from functional magnetic resonance imaging suggests that cortical hemodynamic responses coincide in different subjects experiencing a common naturalistic stimulus. Here we utilize neural responses in the electroencephalogram (EEG) evoked by multiple presentations of short film clips to index brain states marked by high levels of correlation within and across subjects. We formulate a novel signal decomposition method which extracts maximally correlated signal components from multiple EEG records. The resulting components capture correlations down to a one-second time resolution, thus revealing that peak correlations of neural activity across viewings can occur in remarkable correspondence with arousing moments of the film. Moreover, a significant reduction in neural correlation occurs upon a second viewing of the film or when the narrative is disrupted by presenting its scenes scrambled in time. We also probe oscillatory brain activity during periods of heightened correlation, and observe during such times a significant increase in the theta band for a frontal component and reductions in the alpha and beta frequency bands for parietal and occipital components. Low-resolution EEG tomography of these components suggests that the correlated neural activity is consistent with sources in the cingulate and orbitofrontal cortices. Put together, these results suggest that the observed synchrony reflects attention- and emotion-modulated cortical processing which may be decoded with high temporal resolution by extracting maximally correlated components of neural activity.

Human vertical eye movement responses to earth horizontal pitch

Science.gov (United States)

Wall, C. 3rd; Petropoulos, A. E.

1993-01-01

The vertical eye movements in humans produced in response to head-over-heels constant velocity pitch rotation about a horizontal axis resemble those from other species. At 60 degrees/s these are persistent and tend to have non-reversing slow components that are compensatory to the direction of rotation. In most, but not all subjects, the slow component velocity was well characterized by a rapid build-up followed by an exponential decay to a non-zero baseline. Super-imposed was a cyclic or modulation component whose frequency corresponded to the time for one revolution and whose maximum amplitude occurred during a specific head orientation. All response components (exponential decay, baseline and modulation) were larger during pitch backward compared to pitch forward runs. Decay time constants were shorter during the backward runs, thus, unlike left to right yaw axis rotation, pitch responses display significant asymmetries between paired forward and backward runs.

Comparison study of time history and response spectrum responses for multiply supported piping systems

International Nuclear Information System (INIS)

Wang, Y.K.; Subudhi, M.; Bezler, P.

1983-01-01

In the past decade, several investigators have studied the problem of independent support excitation of a multiply supported piping system to identify the real need for such an analysis. This approach offers an increase in accuracy at a small increase in computational costs. To assess the method, studies based on the response spectrum approach using independent support motions for each group of commonly connected supports were performed. The results obtained from this approach were compared with the conventional envelope spectrum and time history solutions. The present study includes a mathematical formulation of the independent support motion analysis method suitable for implementation into an existing all purpose piping code PSAFE2 and a comparison of the solutions for some typical piping system using both Time History and Response Spectrum Methods. The results obtained from the Response Spectrum Methods represent the upper bound solution at most points in the piping system. Similarly, the Seismic Anchor Movement analysis based on the SRP method over predicts the responses near the support points and under predicts at points away from the supports

Response-reinforcer dependency and resistance to change.

Science.gov (United States)

Cançado, Carlos R X; Abreu-Rodrigues, Josele; Aló, Raquel Moreira; Hauck, Flávia; Doughty, Adam H

2018-01-01

The effects of the response-reinforcer dependency on resistance to change were studied in three experiments with rats. In Experiment 1, lever pressing produced reinforcers at similar rates after variable interreinforcer intervals in each component of a two-component multiple schedule. Across conditions, in the fixed component, all reinforcers were response-dependent; in the alternative component, the percentage of response-dependent reinforcers was 100, 50 (i.e., 50% response-dependent and 50% response-independent) or 10% (i.e., 10% response-dependent and 90% response-independent). Resistance to extinction was greater in the alternative than in the fixed component when the dependency in the former was 10%, but was similar between components when this dependency was 100 or 50%. In Experiment 2, a three-component multiple schedule was used. The dependency was 100% in one component and 10% in the other two. The 10% components differed on how reinforcers were programmed. In one component, as in Experiment 1, a reinforcer had to be collected before the scheduling of other response-dependent or independent reinforcers. In the other component, response-dependent and -independent reinforcers were programmed by superimposing a variable-time schedule on an independent variable-interval schedule. Regardless of the procedure used to program the dependency, resistance to extinction was greater in the 10% components than in the 100% component. These results were replicated in Experiment 3 in which, instead of extinction, VT schedules replaced the baseline schedules in each multiple-schedule component during the test. We argue that the relative change in dependency from Baseline to Test, which is greater when baseline dependencies are high rather than low, could account for the differential resistance to change in the present experiments. The inconsistencies in results across the present and previous experiments suggest that the effects of dependency on resistance to change are

The Physiological Basis and Clinical Use of the Binaural Interaction Component of the Auditory Brainstem Response

Science.gov (United States)

Klump, Georg M.; Tollin, Daniel J.

2016-01-01

The auditory brainstem response (ABR) is a sound-evoked non-invasively measured electrical potential representing the sum of neuronal activity in the auditory brainstem and midbrain. ABR peak amplitudes and latencies are widely used in human and animal auditory research and for clinical screening. The binaural interaction component (BIC) of the ABR stands for the difference between the sum of the monaural ABRs and the ABR obtained with binaural stimulation. The BIC comprises a series of distinct waves, the largest of which (DN1) has been used for evaluating binaural hearing in both normal hearing and hearing-impaired listeners. Based on data from animal and human studies, we discuss the possible anatomical and physiological bases of the BIC (DN1 in particular). The effects of electrode placement and stimulus characteristics on the binaurally evoked ABR are evaluated. We review how inter-aural time and intensity differences affect the BIC and, analyzing these dependencies, draw conclusion about the mechanism underlying the generation of the BIC. Finally, the utility of the BIC for clinical diagnoses are summarized. PMID:27232077

10 CFR 603.1000 - Contracting officer's responsibilities at time of award.

Science.gov (United States)

2010-01-01

... 10 Energy 4 2010-01-01 2010-01-01 false Contracting officer's responsibilities at time of award. 603.1000 Section 603.1000 Energy DEPARTMENT OF ENERGY (CONTINUED) ASSISTANCE REGULATIONS TECHNOLOGY INVESTMENT AGREEMENTS Executing the Award § 603.1000 Contracting officer's responsibilities at time of award...

Two discrete components of the 20 Hz steady-state response are distinguished through the modulation of activation level

DEFF Research Database (Denmark)

Griskova, Inga; Mørup, Morten; Parnas, Josef

2009-01-01

Objective: To investigate the modulation of amplitude and phase precision of the auditory steady-state response (SSR) to 20 Hz stimulation in two conditions varying in the level of activation. Methods: Click stimuli (20 Hz) were applied while subjects were sitting upright silently reading a book......-negative multi-way factorization (NMWF). Results: The NMWF decomposition of amplitude and phase precision measures resulted in the observation of two distinct components: a component at the frequency of stimulation – 20 Hz SSR and a component emerging at 40 Hz – 20 Hz SSR-related 40 Hz activity. Modulation...... by the activation level was observed only for 20 Hz SSR-related 40 Hz activity as increased amplitude and phase precision during low activation level. No such effects were observed for 20 Hz SSR. Conclusion: The discrete components of the 20 Hz SSR are distinguished through modulation of activation level, 20 Hz SSR...

Evaluating perceptual integration: uniting response-time- and accuracy-based methodologies.

Science.gov (United States)

Eidels, Ami; Townsend, James T; Hughes, Howard C; Perry, Lacey A

2015-02-01

This investigation brings together a response-time system identification methodology (e.g., Townsend & Wenger Psychonomic Bulletin & Review 11, 391-418, 2004a) and an accuracy methodology, intended to assess models of integration across stimulus dimensions (features, modalities, etc.) that were proposed by Shaw and colleagues (e.g., Mulligan & Shaw Perception & Psychophysics 28, 471-478, 1980). The goal was to theoretically examine these separate strategies and to apply them conjointly to the same set of participants. The empirical phases were carried out within an extension of an established experimental design called the double factorial paradigm (e.g., Townsend & Nozawa Journal of Mathematical Psychology 39, 321-359, 1995). That paradigm, based on response times, permits assessments of architecture (parallel vs. serial processing), stopping rule (exhaustive vs. minimum time), and workload capacity, all within the same blocks of trials. The paradigm introduced by Shaw and colleagues uses a statistic formally analogous to that of the double factorial paradigm, but based on accuracy rather than response times. We demonstrate that the accuracy measure cannot discriminate between parallel and serial processing. Nonetheless, the class of models supported by the accuracy data possesses a suitable interpretation within the same set of models supported by the response-time data. The supported model, consistent across individuals, is parallel and has limited capacity, with the participants employing the appropriate stopping rule for the experimental setting.

Enhancement of concentration range of chromatographically detectable components with array detector mass spectrometry

Science.gov (United States)

Enke, Christie

2013-02-19

Methods and instruments for high dynamic range analysis of sample components are described. A sample is subjected to time-dependent separation, ionized, and the ions dispersed with a constant integration time across an array of detectors according to the ions m/z values. Each of the detectors in the array has a dynamically adjustable gain or a logarithmic response function, producing an instrument capable of detecting a ratio of responses or 4 or more orders of magnitude.

Time-Motion and Biological Responses in Simulated Mixed Martial Arts Sparring Matches.

Science.gov (United States)

Coswig, Victor S; Ramos, Solange de P; Del Vecchio, Fabrício B

2016-08-01

Coswig, VS, Ramos, SdP, and Del Vecchio, FB. Time-motion and biological responses in simulated mixed martial arts sparring matches. J Strength Cond Res 30(8): 2156-2163, 2016-Simulated matches are a relevant component of training for mixed martial arts (MMA) athletes. This study aimed to characterize time-motion responses and investigate physiological stress and neuromuscular changes related to MMA sparring matches. Thirteen athletes with an average age of 25 ± 5 years, body mass of 81.3 ± 9.5 kg, height of 176.2 ± 5.5 cm, and time of practice in MMA of 39 ± 25 months participated in the study. The fighters executed three 5-minute rounds with 1-minute intervals. Blood and salivary samples were collected and physical tests and psychometric questionnaires administered at 3 time points: before (PRE), immediately after (POST), and 48 hours after the combat (48 h). Statistical analysis applied analysis of variance for repeated measurements. In biochemical analysis, significant changes (p ≤ 0.05) were identified between PRE and POST (glucose: 80.3 ± 12.7 to 156.5 ± 19.1 mg·ml; lactate: 4 ± 1.7 to 15.6 ± 4.8 mmol·dl), POST and 48 hours (glucose: 156.5 ± 19.1 to 87.6 ± 15.5 mg·ml; lactate: 15.6 ± 4.8 to 2.9 ± 3.5 mmol·dl; urea: 44.1 ± 8.9 to 36.3 ± 7.8 mg·ml), and PRE and 48 hours (creatine kinase [CK]: 255.8 ± 137.4 to 395.9 ± 188.7 U/L). In addition, time-motion analyses showed a total high:low intensity of 1:2 and an effort:pause ratio of 1:3. In conclusion, simulated MMA sparring matches feature moderate to high intensity and a low degree of musculoskeletal damage, which can be seen by absence of physical performance and decrease in CK. Results of the study indicate that sparring training could be introduced into competitive microcycles to improve technical and tactical aspects of MMA matches, due to the high motor specificity and low muscle damage.

Component-Based Modelling for Scalable Smart City Systems Interoperability: A Case Study on Integrating Energy Demand Response Systems.

Science.gov (United States)

Palomar, Esther; Chen, Xiaohong; Liu, Zhiming; Maharjan, Sabita; Bowen, Jonathan

2016-10-28

Smart city systems embrace major challenges associated with climate change, energy efficiency, mobility and future services by embedding the virtual space into a complex cyber-physical system. Those systems are constantly evolving and scaling up, involving a wide range of integration among users, devices, utilities, public services and also policies. Modelling such complex dynamic systems' architectures has always been essential for the development and application of techniques/tools to support design and deployment of integration of new components, as well as for the analysis, verification, simulation and testing to ensure trustworthiness. This article reports on the definition and implementation of a scalable component-based architecture that supports a cooperative energy demand response (DR) system coordinating energy usage between neighbouring households. The proposed architecture, called refinement of Cyber-Physical Component Systems (rCPCS), which extends the refinement calculus for component and object system (rCOS) modelling method, is implemented using Eclipse Extensible Coordination Tools (ECT), i.e., Reo coordination language. With rCPCS implementation in Reo, we specify the communication, synchronisation and co-operation amongst the heterogeneous components of the system assuring, by design scalability and the interoperability, correctness of component cooperation.

Ultimate response time of high electron mobility transistors

International Nuclear Information System (INIS)

Rudin, Sergey; Rupper, Greg; Shur, Michael

2015-01-01

We present theoretical studies of the response time of the two-dimensional gated electron gas to femtosecond pulses. Our hydrodynamic simulations show that the device response to a short pulse or a step-function signal is either smooth or oscillating time-decay at low and high mobility, μ, values, respectively. At small gate voltage swings, U 0  = U g  − U th , where U g is the gate voltage and U th is the threshold voltage, such that μU 0 /L < v s , where L is the channel length and v s is the effective electron saturation velocity, the decay time in the low mobility samples is on the order of L 2 /(μU 0 ), in agreement with the analytical drift model. However, the decay is preceded by a delay time on the order of L/s, where s is the plasma wave velocity. This delay is the ballistic transport signature in collision-dominated devices, which becomes important during very short time periods. In the high mobility devices, the period of the decaying oscillations is on the order of the plasma wave velocity transit time. Our analysis shows that short channel field effect transistors operating in the plasmonic regime can meet the requirements for applications as terahertz detectors, mixers, delay lines, and phase shifters in ultra high-speed wireless communication circuits

More is not Always Better: The Relation between Item Response and Item Response Time in Raven’s Matrices

Directory of Open Access Journals (Sweden)

Frank Goldhammer

2015-03-01

Full Text Available The role of response time in completing an item can have very different interpretations. Responding more slowly could be positively related to success as the item is answered more carefully. However, the association may be negative if working faster indicates higher ability. The objective of this study was to clarify the validity of each assumption for reasoning items considering the mode of processing. A total of 230 persons completed a computerized version of Raven’s Advanced Progressive Matrices test. Results revealed that response time overall had a negative effect. However, this effect was moderated by items and persons. For easy items and able persons the effect was strongly negative, for difficult items and less able persons it was less negative or even positive. The number of rules involved in a matrix problem proved to explain item difficulty significantly. Most importantly, a positive interaction effect between the number of rules and item response time indicated that the response time effect became less negative with an increasing number of rules. Moreover, exploratory analyses suggested that the error type influenced the response time effect.

Time-Lapse and Slow-Motion Tracking of Temperature Changes: Response Time of a Thermometer

Science.gov (United States)

Moggio, L.; Onorato, P.; Gratton, L. M.; Oss, S.

2017-01-01

We propose the use of a smartphone based time-lapse and slow-motion video techniques together with tracking analysis as valuable tools for investigating thermal processes such as the response time of a thermometer. The two simple experimental activities presented here, suitable also for high school and undergraduate students, allow one to measure…

Shaking table test and dynamic response analysis of 3-D component base isolation system using multi-layer rubber bearings and coil springs

Energy Technology Data Exchange (ETDEWEB)

Tsutsumi, Hideaki; Yamada, Hiroyuki; Ebisawa, Katsumi; Shibata, Katsuyuki [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Fujimoto, Shigeru [Toshiba Corp., Tokyo (Japan)

2001-06-01

Introduction of the base isolation technique into the seismic design of nuclear power plant components as well as buildings has been expected as one of the effective countermeasure to reduce the seismic force applied to components. A research program on the base isolation of nuclear components has been carried out at the Japan Atomic Energy Research Institute (JAERI) since 1991. A methodology and a computer code (EBISA: Equipment Base Isolation System Analysis) for evaluating the failure frequency of the nuclear component with the base isolation were developed. In addition, a test program, which is concerned with the above development, aiming at improvement of failure frequency analysis models in the code has been conducted since 1996 to investigate the dynamic behavior and to verify the effectiveness of component base isolation systems. Two base isolation test systems with different characteristics were fabricated and static and dynamic characteristics were measured by static loading and free vibration tests. One which consists of ball bearings and air springs was installed on the test bed to observe the dynamic response under natural earthquake motion. The effect of base isolation system has been observed under several earthquakes. Three-dimensional response and effect of base isolation of another system using multi-layer-rubber-bearings and coil springs has been investigated under various large earthquake motions by shaking table test. This report describes the results of the shaking table tests and dynamic response analysis. (author)

Responses to interracial interactions over time.

Science.gov (United States)

Plant, E Ashby

2004-11-01

The current work tested and expanded on Plant and Devine's (2003) model of the antecedents and implications of interracial anxiety by examining people's experiences with interracial interactions at two time points. Study 1 explored non-Black people's responses to interactions with Black people and Study 2 explored Black people's responses to interactions with White people. Non-Black participants' expectancies about coming across as biased in interracial interactions and Black participants' expectancies about White people's bias predicted their interracial anxiety and whether they had positive interactions with outgroup members during the 2 weeks between assessments. Across both studies, interracial anxiety predicted the desire to avoid interactions with outgroup members. In addition, participants who were personally motivated to respond without prejudice reported more positive expectancies. The findings are discussed in terms of the implications for understanding the course and quality of interracial interactions.

Development of a Real-Time GPS/Seismic Displacement Meter: Seismic Component and Communications

Science.gov (United States)

Vernon, F.; Bock, Y.

2002-12-01

, hydrological, ecological, and physical data to a variety of end users in real-time. In this abstract we report on the seismic component, as well as the communications infrastructure. In the second abstract, we we describe the first implementation of the GPS component in Orange County.

Time-dependent extraction kinetics of infused components of different Indian black tea types using UV spectroscopy

Directory of Open Access Journals (Sweden)

Asir Gani

2016-12-01

Full Text Available Time-dependent aqueous extraction of six tea types was carried out with leaf–water–ratio of 0.5 g/100 ml, temperature of extraction 90°C and time of extraction ranging from 1 to 10 min. UV–vis spectroscopic analysis in the range varying from 220 to 900 nm of the aqueous tea extracts showed a prominent peak at 273 nm in the ultraviolet region which can be associated with n → π* electronic transition of caffeine molecules. Parabolic diffusion, Power law, hyperbolic, Weibull’s and Elovich’s models were fitted to represent the aqueous soluble component extraction behaviour for time-dependent extraction of aqueous extractables. Parabolic diffusion model, Power law and Elovich’s model were a close fit to the experimental data for all the selected tea types with correlation coefficients (R2 ranging 0.8029–0.9953, whereas hyperbolic and Weibull’s models showed poor fitness to represent the extraction behaviour of fanning and AO leaf, LD, fanning and dust, respectively, with R2 < 0.8, for time-dependent aqueous soluble component extraction.

Simulations of hybrid system varying solar radiation and microturbine response time

Directory of Open Access Journals (Sweden)

Yolanda Fernández Ribaya

2015-07-01

Full Text Available Hybrid power systems, such as combinations of renewable power sources with intermittent power production and non-renewable power sources, theoretically increase the reliability and thus integration of renewable sources in the electrical system. However, a recent increase in the number of hybrid installations has sparked interest in the effects of their connection to the grid, especially in remote areas. This paper analyses a photovoltaic-gas microturbine hybrid system dimensioned to be installed in La Paz (Mexico.The research presented in this paper studies and quantifies the effects on the total electric power produced, varying both the solar radiation and the gas microturbine response time. The gas microturbine and the photovoltaic panels are modelled using Matlab/Simulink software, obtaining a platform where different tests to simulate real conditions have been executed. They consist of diverse ramps of irradiance that replicate solar radiation variations, and different microturbine response times reproduced by the time constants of a first order transfer function that models the microturbine dynamic response. The results obtained show that when radiation varies quickly it does not produce significant differences in the power guarantee or the microturbine gas consumption, to any microturbine response time. However, these two parameters are highly variable with smooth radiance variations. The maximum total power variation decreases greatly as the radiation variation gets lower. In addition, by decreasing the microturbine response time, it is possible to appreciably increase the power guarantee although the maximum power variation and gas consumption increase. Only in cases of low radiation variation is there no appreciable difference in the maximum power variation obtained by the different turbine response times.

Simulations of hybrid system varying solar radiation and microturbine response time

Energy Technology Data Exchange (ETDEWEB)

Fernández Ribaya, Yolanda, E-mail: fernandezryolanda@uniovi.es; Álvarez, Eduardo; Paredes Sánchez, José Pablo; Xiberta Bernat, Jorge [Department of Energy E.I.M.E.M., University of Oviedo. 13 Independencia Street 2" n" d floor, 36004, Oviedo (Spain)

2015-07-15

Hybrid power systems, such as combinations of renewable power sources with intermittent power production and non-renewable power sources, theoretically increase the reliability and thus integration of renewable sources in the electrical system. However, a recent increase in the number of hybrid installations has sparked interest in the effects of their connection to the grid, especially in remote areas. This paper analyses a photovoltaic-gas microturbine hybrid system dimensioned to be installed in La Paz (Mexico).The research presented in this paper studies and quantifies the effects on the total electric power produced, varying both the solar radiation and the gas microturbine response time. The gas microturbine and the photovoltaic panels are modelled using Matlab/Simulink software, obtaining a platform where different tests to simulate real conditions have been executed. They consist of diverse ramps of irradiance that replicate solar radiation variations, and different microturbine response times reproduced by the time constants of a first order transfer function that models the microturbine dynamic response. The results obtained show that when radiation varies quickly it does not produce significant differences in the power guarantee or the microturbine gas consumption, to any microturbine response time. However, these two parameters are highly variable with smooth radiance variations. The maximum total power variation decreases greatly as the radiation variation gets lower. In addition, by decreasing the microturbine response time, it is possible to appreciably increase the power guarantee although the maximum power variation and gas consumption increase. Only in cases of low radiation variation is there no appreciable difference in the maximum power variation obtained by the different turbine response times.

Identification of chemical components of combustion emissions that affect pro-atherosclerotic vascular responses in mice

OpenAIRE

Seilkop, Steven K.; Campen, Matthew J.; Lund, Amie K.; McDonald, Jacob D.; Mauderly, Joe L.

2012-01-01

Combustion emissions cause pro-atherosclerotic responses in apolipoprotein E-deficient (ApoE/−) mice, but the causal components of these complex mixtures are unresolved. In studies previously reported, ApoE−/− mice were exposed by inhalation 6 h/day for 50 consecutive days to multiple dilutions of diesel or gasoline exhaust, wood smoke, or simulated “downwind” coal emissions. In this study, the analysis of the combined four-study database using the Multiple Additive Regression Trees (MART) da...

Criteria for the generation of spectra consistent time histories

International Nuclear Information System (INIS)

Lin, C.-W.

1977-01-01

Several methods are available to conduct seismic analysis for nuclear power plant systems and components. Among them, the response spectrum technique has been most widely adopted for linear type of modal analysis. However, for designs which consist of structural or material nonlinearites such as frequency dependent soil properties, the existance of gaps, single tie rods, and friction between supports where the response has to be computed as a function of time, time history approach is the only viable method of analysis. Two examples of time history analysis are: 1) soil-structure interaction study and, 2) a coupled reactor coolant system and building analysis to either generate the floor response specra or compute nonlinear system time history response. The generation of a suitable time history input for the analysis has been discussed in the literature. Some general guidelines are available to insure that the time history imput will be as conservative as the design response spectra. Very little has been reported as to the effect of the dyanmic characteristics of the time history input upon the system response. In fact, the only available discussion in this respect concerns only with the statitical independent nature of the time history components. In this paper, numerical results for cases using the time history approach are presented. Criteria are also established which may be advantageously used to arrive at spectra consistent time histories which are conservative and more importantly, realistic. (Auth.)

In situ response time measurements of RTD temperature sensors

International Nuclear Information System (INIS)

Goncalves, I.M.P.

1985-01-01

The loop-current-step-response test provides a mean for determining the time constant of resistence thermometers. The test consist in heating the sensor a few degrees above ambient temperature by causing a step pertubation in the electric current that flows through the sensor leads. The developed mathematical transformation permits to use data collected during the internal heating transient to predict the sensor response to perturbations in fluid temperature. Experimental data obtained show that the time constant determined by method is within 15 percent of true value. The loop-current-step-response test is a remote in situ test, which can be performed with the sensor installed in the process. Consequently it takes account the local heat transfer conditions, and appropriated for nuclear power plants, where sensors are installed in points of difficult access. (author) [pt

Lactoferricin B Inhibits the Phosphorylation of the Two-Component System Response Regulators BasR and CreB*

Science.gov (United States)

Ho, Yu-Hsuan; Sung, Tzu-Cheng; Chen, Chien-Sheng

2012-01-01

Natural antimicrobial peptides provide fundamental protection for multicellular organisms from microbes, such as Lactoferricin B (Lfcin B). Many studies have shown that Lfcin B penetrates the cell membrane and has intracellular activities. To elucidate the intracellular behavior of Lfcin B, we first used Escherichia coli K12 proteome chips to identify the intracellular targets of Lfcin B. The results showed that Lfcin B binds to two response regulators, BasR and CreB, of the two-component system. For further analysis, we conducted several in vitro and in vivo experiments and utilized bioinformatics methods. The electrophoretic mobility shift assays and kinase assays indicate that Lfcin B inhibits the phosphorylation of the response regulators (BasR and CreB) and their cognate sensor kinases (BasS and CreC). Antibacterial assays showed that Lfcin B reduced E. coli's tolerance to environmental stimuli, such as excessive ferric ions and minimal medium conditions. This is the first study to show that an antimicrobial peptide inhibits the growth of bacteria by influencing the phosphorylation of a two-component system directly. PMID:22138548

Lactoferricin B inhibits the phosphorylation of the two-component system response regulators BasR and CreB.

Science.gov (United States)

Ho, Yu-Hsuan; Sung, Tzu-Cheng; Chen, Chien-Sheng

2012-04-01

Natural antimicrobial peptides provide fundamental protection for multicellular organisms from microbes, such as Lactoferricin B (Lfcin B). Many studies have shown that Lfcin B penetrates the cell membrane and has intracellular activities. To elucidate the intracellular behavior of Lfcin B, we first used Escherichia coli K12 proteome chips to identify the intracellular targets of Lfcin B. The results showed that Lfcin B binds to two response regulators, BasR and CreB, of the two-component system. For further analysis, we conducted several in vitro and in vivo experiments and utilized bioinformatics methods. The electrophoretic mobility shift assays and kinase assays indicate that Lfcin B inhibits the phosphorylation of the response regulators (BasR and CreB) and their cognate sensor kinases (BasS and CreC). Antibacterial assays showed that Lfcin B reduced E. coli's tolerance to environmental stimuli, such as excessive ferric ions and minimal medium conditions. This is the first study to show that an antimicrobial peptide inhibits the growth of bacteria by influencing the phosphorylation of a two-component system directly.

Corrective response times in a coordinated eye-head-arm countermanding task.

Science.gov (United States)

Tao, Gordon; Khan, Aarlenne Z; Blohm, Gunnar

2018-06-01

Inhibition of motor responses has been described as a race between two competing decision processes of motor initiation and inhibition, which manifest as the reaction time (RT) and the stop signal reaction time (SSRT); in the case where motor initiation wins out over inhibition, an erroneous movement occurs that usually needs to be corrected, leading to corrective response times (CRTs). Here we used a combined eye-head-arm movement countermanding task to investigate the mechanisms governing multiple effector coordination and the timing of corrective responses. We found a high degree of correlation between effector response times for RT, SSRT, and CRT, suggesting that decision processes are strongly dependent across effectors. To gain further insight into the mechanisms underlying CRTs, we tested multiple models to describe the distribution of RTs, SSRTs, and CRTs. The best-ranked model (according to 3 information criteria) extends the LATER race model governing RTs and SSRTs, whereby a second motor initiation process triggers the corrective response (CRT) only after the inhibition process completes in an expedited fashion. Our model suggests that the neural processing underpinning a failed decision has a residual effect on subsequent actions. NEW & NOTEWORTHY Failure to inhibit erroneous movements typically results in corrective movements. For coordinated eye-head-hand movements we show that corrective movements are only initiated after the erroneous movement cancellation signal has reached a decision threshold in an accelerated fashion.

Correlated Components of Ongoing EEG Point to Emotionally Laden Attention – A Possible Marker of Engagement?

Science.gov (United States)

Dmochowski, Jacek P.; Sajda, Paul; Dias, Joao; Parra, Lucas C.

2012-01-01

Recent evidence from functional magnetic resonance imaging suggests that cortical hemodynamic responses coincide in different subjects experiencing a common naturalistic stimulus. Here we utilize neural responses in the electroencephalogram (EEG) evoked by multiple presentations of short film clips to index brain states marked by high levels of correlation within and across subjects. We formulate a novel signal decomposition method which extracts maximally correlated signal components from multiple EEG records. The resulting components capture correlations down to a one-second time resolution, thus revealing that peak correlations of neural activity across viewings can occur in remarkable correspondence with arousing moments of the film. Moreover, a significant reduction in neural correlation occurs upon a second viewing of the film or when the narrative is disrupted by presenting its scenes scrambled in time. We also probe oscillatory brain activity during periods of heightened correlation, and observe during such times a significant increase in the theta band for a frontal component and reductions in the alpha and beta frequency bands for parietal and occipital components. Low-resolution EEG tomography of these components suggests that the correlated neural activity is consistent with sources in the cingulate and orbitofrontal cortices. Put together, these results suggest that the observed synchrony reflects attention- and emotion-modulated cortical processing which may be decoded with high temporal resolution by extracting maximally correlated components of neural activity. PMID:22623915

Habituation of the cold shock response may include a significant perceptual component.

Science.gov (United States)

Barwood, Martin J; Corbett, Jo; Wagstaff, Christopher R D

2014-02-01

Accidental immersion in cold water is a risk factor for many occupations. Habituation to cold-water immersion (CWI) is one practical means of reducing the cold shock response (CSR) on immersion. We investigated whether repeated thermoneutral water immersion (TWI) induced a perceptual habituation (i.e., could lessen perceived threat and anxiety) and consequently reduce the CSR on subsequent CWI. There were 12 subjects who completed seven 7-min head-out immersions. Immersions one and seven were CWls [15.0 (0.1) degrees C], and immersions two to six were TWI [34.9 (0.10) degrees C]. Anxiety 120-cm visual analogue scale) and the cardiorespiratory responses [heart rate (f(C)), respiratory frequency (f(R)), tidal volume (V(T)), and minute ventilation (V(E))] to immersion were measured throughout. Data were compared within subject between conditions using ANOVA to an alpha level of 0.05. Acute anxiety was significantly reduced after repeated exposure to the immersion scenario (i.e., TWI): CWI-1: 6.3 (4.4) cm; and CWI-2: 4.5 (4.0) cm [condition mean (SD)]. These differences did not influence the peak in the CSR. The f(C), f(R), and V(E) responses were similar between CWI-1 and CWI-2. V(T) response was significantly lower in CWI-2; mean (SD) across the immersion: CWI-1 1.27 (0.17) vs. CWI-2 1.11 0.21 L. Repeated TWI lessened the anxiety associated with CWI (perceptual habituation). This had a negligible effect on the primary components of the CSR, but did lower VT, which may reduce the volume of any aspirated water in an emergency situation. Reducing the threat appraisal of an environmental stressor may be a useful biproduct of survival training, thereby minimizing psychophysiological strain.

Multi-level Simulation of a Real Time Vibration Monitoring System Component

Science.gov (United States)

Robertson, Bryan A.; Wilkerson, Delisa

2005-01-01

This paper describes the development of a custom built Digital Signal Processing (DSP) printed circuit board designed to implement the Advanced Real Time Vibration Monitoring Subsystem proposed by Marshall Space Flight Center (MSFC) Transportation Directorate in 2000 for the Space Shuttle Main Engine Advanced Health Management System (AHMS). This Real Time Vibration Monitoring System (RTVMS) is being developed for ground use as part of the AHMS Health Management Computer-Integrated Rack Assembly (HMC-IRA). The HMC-IRA RTVMS design contains five DSPs which are highly interconnected through individual communication ports, shared memory, and a unique communication router that allows all the DSPs to receive digitized data fiom two multi-channel analog boards simultaneously. This paper will briefly cover the overall board design but will focus primarily on the state-of-the-art simulation environment within which this board was developed. This 16-layer board with over 1800 components and an additional mezzanine card has been an extremely challenging design. Utilization of a Mentor Graphics simulation environment provided the unique board and system level simulation capability to ascertain any timing or functional concerns before production. By combining VHDL, Synopsys Software and Hardware Models, and the Mentor Design Capture Environment, multiple simulations were developed to verify the RTVMS design. This multi-level simulation allowed the designers to achieve complete operability without error the first time the RTVMS printed circuit board was powered. The HMC-IRA design has completed all engineering and deliverable unit testing. P

Multidisciplinary Difficult Airway Course: An Essential Educational Component of a Hospital-Wide Difficult Airway Response Program.

Science.gov (United States)

Leeper, W Robert; Haut, Elliott R; Pandian, Vinciya; Nakka, Sajan; Dodd-O, Jeffrey; Bhatti, Nasir; Hunt, Elizabeth A; Saheed, Mustapha; Dalesio, Nicholas; Schiavi, Adam; Miller, Christina; Kirsch, Thomas D; Berkow, Lauren

2018-04-05

A hospital-wide difficult airway response team was developed in 2008 at The Johns Hopkins Hospital with three central pillars: operations, safety monitoring, and education. The objective of this study was to assess the outcomes of the educational pillar of the difficult airway response team program, known as the multidisciplinary difficult airway course (MDAC). The comprehensive, full-day MDAC involves trainees and staff from all provider groups who participate in airway management. The MDAC occurs within the Johns Hopkins Medicine Simulation Center approximately four times per year and uses a combination of didactic lectures, hands-on sessions, and high-fidelity simulation training. Participation in MDAC is the main intervention being investigated in this study. Data were collected prospectively using course evaluation survey with quantitative and qualitative components, and prepost course knowledge assessment multiple choice questions (MCQ). Outcomes include course evaluation scores and themes derived from qualitative assessments, and prepost course knowledge assessment MCQ scores. Tertiary care academic hospital center PARTICIPANTS: Students, residents, fellows, and practicing physicians from the departments of Surgery, Otolaryngology Head and Neck Surgery, Anesthesiology/Critical Care Medicine, and Emergency Medicine; advanced practice providers (nurse practitioners and physician assistants), nurse anesthetists, nurses, and respiratory therapists. Totally, 23 MDACs have been conducted, including 499 participants. Course evaluations were uniformly positive with mean score of 86.9 of 95 points. Qualitative responses suggest major value from high-fidelity simulation, the hands-on skill stations, and teamwork practice. MCQ scores demonstrated significant improvement: median (interquartile range) pre: 69% (60%-81%) vs post: 81% (72%-89%), p < 0.001. Implementation of a MDAC successfully disseminated principles and protocols to all airway providers. Demonstrable

A Comparison of Two Objective Measures of Binaural Processing: The Interaural Phase Modulation Following Response and the Binaural Interaction Component.

Science.gov (United States)

Haywood, Nicholas R; Undurraga, Jaime A; Marquardt, Torsten; McAlpine, David

2015-12-30

There has been continued interest in clinical objective measures of binaural processing. One commonly proposed measure is the binaural interaction component (BIC), which is obtained typically by recording auditory brainstem responses (ABRs)-the BIC reflects the difference between the binaural ABR and the sum of the monaural ABRs (i.e., binaural - (left + right)). We have recently developed an alternative, direct measure of sensitivity to interaural time differences, namely, a following response to modulations in interaural phase difference (the interaural phase modulation following response; IPM-FR). To obtain this measure, an ongoing diotically amplitude-modulated signal is presented, and the interaural phase difference of the carrier is switched periodically at minima in the modulation cycle. Such periodic modulations to interaural phase difference can evoke a steady state following response. BIC and IPM-FR measurements were compared from 10 normal-hearing subjects using a 16-channel electroencephalographic system. Both ABRs and IPM-FRs were observed most clearly from similar electrode locations-differential recordings taken from electrodes near the ear (e.g., mastoid) in reference to a vertex electrode (Cz). Although all subjects displayed clear ABRs, the BIC was not reliably observed. In contrast, the IPM-FR typically elicited a robust and significant response. In addition, the IPM-FR measure required a considerably shorter recording session. As the IPM-FR magnitude varied with interaural phase difference modulation depth, it could potentially serve as a correlate of perceptual salience. Overall, the IPM-FR appears a more suitable clinical measure than the BIC. © The Author(s) 2015.

Independent Component Analysis and Time-Frequency Masking for Speech Recognition in Multitalker Conditions

Directory of Open Access Journals (Sweden)

Reinhold Orglmeister

2010-01-01

Full Text Available When a number of speakers are simultaneously active, for example in meetings or noisy public places, the sources of interest need to be separated from interfering speakers and from each other in order to be robustly recognized. Independent component analysis (ICA has proven a valuable tool for this purpose. However, ICA outputs can still contain strong residual components of the interfering speakers whenever noise or reverberation is high. In such cases, nonlinear postprocessing can be applied to the ICA outputs, for the purpose of reducing remaining interferences. In order to improve robustness to the artefacts and loss of information caused by this process, recognition can be greatly enhanced by considering the processed speech feature vector as a random variable with time-varying uncertainty, rather than as deterministic. The aim of this paper is to show the potential to improve recognition of multiple overlapping speech signals through nonlinear postprocessing together with uncertainty-based decoding techniques.

Age-related differences in working memory updating components.

Science.gov (United States)

Linares, Rocío; Bajo, M Teresa; Pelegrina, Santiago

2016-07-01

The aim of this study was to investigate possible age-related changes throughout childhood and adolescence in different component processes of working memory updating (WMU): retrieval, transformation, and substitution. A set of numerical WMU tasks was administered to four age groups (8-, 11-, 14-, and 21-year-olds). To isolate the effect of each of the WMU components, participants performed different versions of a task that included different combinations of the WMU components. The results showed an expected overall decrease in response times and an increase in accuracy performance with age. Most important, specific age-related changes in the retrieval component were found, demonstrating that the effect of retrieval on accuracy was larger in children than in adolescents or young adults. These findings indicate that the availability of representations from outside the focus of attention may change with age. Thus, the retrieval component of updating could contribute to the age-related changes observed in the performance of many updating tasks. Copyright © 2016 Elsevier Inc. All rights reserved.

Thermal-structural response of EBR-II major components under reactor operational transients

International Nuclear Information System (INIS)

Chang, L.K.; Lee, M.J.

1983-01-01

Until recently, the LMFBR safety research has been focused primarily on severe but highly unlikely accident, such as hypothetical-core-disruptive accidents (HCDA's), and not enough attention has been given to accident prevention, which is less severe but more likely sequence. The objective of the EBR-II operational reliability testing (ORT) is to demonstrate that the reactor can be designed and operated to prevent accident. A series of mild duty cycles and overpower transients were designed for accident prevention tests. An assessment of the EBR-II major plant components has been performed to assure structural integrity of the reactor plant for the ORT program. In this paper, the thermal-structural response and structural evaluation of the reactor vessel, the reactor-vessel cover, the intermediate heat exchanger (IHX) and the superheater are presented

Ionospheric convection response to changes of interplanetary magnetic field B-z component during strong B-y component

DEFF Research Database (Denmark)

Huang, C.S.; Murr, D.; Sofko, G.J.

2000-01-01

response to IMF Bz changes during strong IMF BZ. On March 23, 1995, B-x was small, B-y was strongly positive (7-11 nT), and the B-z polarity changed several times after 1300 UT. The dayside ionospheric convection is dominated by a large clockwise convection cell. The cell focus (the "eye" of the convection...... cell, or the largest change in the convection pattern, is limited roughly to the region between the previous cell focus and the new cell focus. Outside this region, the ionospheric flows could be greatly enhanced or weakened, while the convection pattern shape changes very little. When B-y is strong...... the dawn-dusk meridian plane, which is interpreted as propagation or expansion of newly generated convection cells in the cusp region. Other studies showed that the change in convection pattern in response to IMF reorientations is spatially fixed. In this paper, we investigate the ionospheric convection...

Functional Dissociation of Latency-Variable, Stimulus- and Response-Locked Target P3 Sub-components in Task-Switching.

Science.gov (United States)

Brydges, Christopher R; Barceló, Francisco

2018-01-01

Cognitive control warrants efficient task performance in dynamic and changing environments through adjustments in executive attention, stimulus and response selection. The well-known P300 component of the human event-related potential (ERP) has long been proposed to index "context-updating"-critical for cognitive control-in simple target detection tasks. However, task switching ERP studies have revealed both target P3 (300-350 ms) and later sustained P3-like potentials (400-1,200 ms) to first targets ensuing transition cues, although it remains unclear whether these target P3-like potentials also reflect context updating operations. To address this question, we applied novel single-trial EEG analyses-residue iteration decomposition (RIDE)-in order to disentangle target P3 sub-components in a sample of 22 young adults while they either repeated or switched (updated) task rules. The rationale was to revise the context updating hypothesis of P300 elicitation in the light of new evidence suggesting that "the context" consists of not only the sensory units of stimulation, but also associated motor units, and intermediate low- and high-order sensorimotor units, all of which may need to be dynamically updated on a trial by trial basis. The results showed functionally distinct target P3-like potentials in stimulus-locked, response-locked, and intermediate RIDE component clusters overlying parietal and frontal regions, implying multiple functionally distinct, though temporarily overlapping context updating operations. These findings support a reformulated version of the context updating hypothesis, and reveal a rich family of distinct target P3-like sub-components during the reactive control of target detection in task-switching, plausibly indexing the complex and dynamic workings of frontoparietal cortical networks subserving cognitive control.

Progressive recruitment of muscle fibers is not necessary for the slow component of VO2 kinetics.

Science.gov (United States)

Zoladz, Jerzy A; Gladden, L Bruce; Hogan, Michael C; Nieckarz, Zenon; Grassi, Bruno

2008-08-01

The "slow component" of O2 uptake (VO2) kinetics during constant-load heavy-intensity exercise is traditionally thought to derive from a progressive recruitment of muscle fibers. In this study, which represents a reanalysis of data taken from a previous study by our group (Grassi B, Hogan MC, Greenhaff PL, Hamann JJ, Kelley KM, Aschenbach WG, Constantin-Teodosiu D, Gladden LB. J Physiol 538: 195-207, 2002) we evaluated the presence of a slow component-like response in the isolated dog gastrocnemius in situ (n=6) during 4 min of contractions at approximately 60-70% of peak VO2. In this preparation all muscle fibers are maximally activated by electrical stimulation from the beginning of the contraction period, and no progressive recruitment of fibers is possible. Muscle VO2 was calculated as blood flow multiplied by arteriovenous O2 content difference. The muscle fatigued (force decreased by approximately 20-25%) during contractions. Kinetics of adjustment were evaluated for 1) VO2, uncorrected for force development; 2) VO2 normalized for peak force; 3) VO2 normalized for force-time integral. A slow component-like response, described in only one muscle out of six when uncorrected VO2 was considered, was observed in all muscles when VO2/peak force and VO2/force-time were considered. The amplitude of the slow component-like response, expressed as a fraction of the total response, was higher for VO2/peak force (0.18+/-0.06, means+/-SE) and for VO2/force-time (0.22+/-0.05) compared with uncorrected VO2 (0.04+/-0.04). A progressive recruitment of muscle fibers may not be necessary for the development of the slow component of VO2 kinetics, which may be caused by the metabolic factors that induce muscle fatigue and, as a consequence, reduce the efficiency of muscle contractions.

Reduced computational cost in the calculation of worst case response time for real time systems

OpenAIRE

Urriza, José M.; Schorb, Lucas; Orozco, Javier D.; Cayssials, Ricardo

2009-01-01

Modern Real Time Operating Systems require reducing computational costs even though the microprocessors become more powerful each day. It is usual that Real Time Operating Systems for embedded systems have advance features to administrate the resources of the applications that they support. In order to guarantee either the schedulability of the system or the schedulability of a new task in a dynamic Real Time System, it is necessary to know the Worst Case Response Time of the Real Time tasks ...

Optimization of Extraction Process for Antidiabetic and Antioxidant Activities of Kursi Wufarikun Ziyabit Using Response Surface Methodology and Quantitative Analysis of Main Components.

Science.gov (United States)

Edirs, Salamet; Turak, Ablajan; Numonov, Sodik; Xin, Xuelei; Aisa, Haji Akber

2017-01-01

By using extraction yield, total polyphenolic content, antidiabetic activities (PTP-1B and α -glycosidase), and antioxidant activity (ABTS and DPPH) as indicated markers, the extraction conditions of the prescription Kursi Wufarikun Ziyabit (KWZ) were optimized by response surface methodology (RSM). Independent variables were ethanol concentration, extraction temperature, solid-to-solvent ratio, and extraction time. The result of RSM analysis showed that the four variables investigated have a significant effect ( p analysis of effective part of KWZ was characterized via UPLC method, 12 main components were identified by standard compounds, and all of them have shown good regression within the test ranges and the total content of them was 11.18%.

Time for a revolution: smart energy and microgrid use in disaster response.

Science.gov (United States)

Callaway, David Wayne; Noste, Erin; McCahill, Peter Woods; Rossman, A J; Lempereur, Dominique; Kaney, Kathleen; Swanson, Doug

2014-06-01

Modern health care and disaster response are inextricably linked to high volume, reliable, quality power. Disasters place major strain on energy infrastructure in affected communities. Advances in renewable energy and microgrid technology offer the potential to improve mobile disaster medical response capabilities. However, very little is known about the energy requirements of and alternative power sources in disaster response. A gap analysis of the energy components of modern disaster response reveals multiple deficiencies. The MED-1 Green Project has been executed as a multiphase project designed to identify energy utilization inefficiencies, decrease demands on diesel generators, and employ modern energy management strategies to expand operational independence. This approach, in turn, allows for longer deployments in potentially more austere environments and minimizes the unit's environmental footprint. The ultimate goal is to serve as a proof of concept for other mobile medical units to create strategies for energy independence.

A new creep-strain-replica method for evaluating the remaining life time of components

International Nuclear Information System (INIS)

Joas, H.D.

2001-01-01

To realise a safe and economic operation of older power- or chemical plants a strategy for maintenance is necessary, which makes it possible to operate a component or the plant longer than 300,000 operating hours, this also for the situation that the mode of operation has changed meanwhile. In Germany a realistic evaluation of the remaining life-time is done by comparing the actual calculated test data of a component with the code TRD 301 and TRD 508 and additional non-destructive tests or other codes like ASME, Sec. II, BS 5500, AFCEN (1985). According to many boundary conditions, the calculated data are inaccurate and the measuring of creep-strain at temperatures of about 600 o C with capacitive strain-gauges very expensive. Description of the approach of the problems: spotwelding of two gauges to the surface of a component (in a defined distance), forming a gap, producing of replica of the gap after certain operating hours at shut-down conditions by trained personal, evaluation of the replica to gain the amount of creep-strain using a scanning electron microscope, assessment of the creep-strain data. (Author)

Impact of insufficient energy content in the design time history on the structure response

International Nuclear Information System (INIS)

Ma, D.C.; Gvildys, J.; Chang, Y.W.; Seidensticker, R.W.

1989-01-01

In the design of nuclear power plants, it is often desirable to use the time history method in the soil-structure interaction analysis to determine the plant floor response to seismic loads. Because many design criteria are specified in terms of design response spectra, the artificial time history needs to be generated under the requirement that the response spectra of the artificial history should envelop the given design response spectra. However, recent studies indicate that the artificial time history used in the plant design may have insufficient energy in the frequency range of interest, even though the response spectra of the design time history closely envelop the design response spectra. This paper presents an investigation of the effects of the insufficient energy content in the design time history on the response of the soil-structure system. Numerical studies were carried out. Both the real earthquake records and the artificial time histories were used as the input motions in a simple lumped-mass soil-structure interaction model. The results obtained from this study provide a better understanding of the effects of the insufficient energy content in the design time history on the structural response

Relationship Between Time Consumption and Quality of Responses to Drug-related Queries

DEFF Research Database (Denmark)

Amundstuen Reppe, Linda; Lydersen, Stian; Schjøtt, Jan

2016-01-01

in score, –0.05 per hour of work; 95% CI, –0.08 to –0.01; P = 0.005). No such associations were found for the internal experts’ assessment. Implications To our knowledge, this is the first study of the association between time consumption and quality of responses to drug-related queries in DICs......Purpose The aims of this study were to assess the quality of responses produced by drug information centers (DICs) in Scandinavia, and to study the association between time consumption processing queries and the quality of the responses. Methods We posed six identical drug-related queries to seven...... DICs in Scandinavia, and the time consumption required for processing them was estimated. Clinical pharmacologists (internal experts) and general practitioners (external experts) reviewed responses individually. We used mixed model linear regression analyses to study the associations between time...

Generation of artificial time-histories, rich in all frequencies, from given response spectra

International Nuclear Information System (INIS)

Levy, S.; Wilkinson, J.P.D.

1976-01-01

In the design of nuclear power plants, it has been found desirable in certain instances to use the time-history method of dynamic analysis to determine the plant response to seismic input. In the implementation of this method, it is necessary to determine an adequate representation of the excitation as a function of time. Because many design criteria are specified in terms of design response spectra one is faced with the problem of generating a time-history whose own response spectrum approximates as far as possible to the originally specified design response spectrum. One objective of this paper is to present a method of synthesizing such time-histories from a given design response spectrum. The design response spectra may be descriptive of floor responses at a particular location in a plant, or they may be descriptive of seismic ground motions at a plant site. The method described in this paper allows the generation of time histories that are rich in all frequencies in the spectrum. This richness is achieved by choosing a large number of closely-spaced frequency points such that the half-power points of adjacent frequencies overlap. Examples are given concerning seismic design response spectra, and a number of points are discussed concerning the effect of frequency spacing on convergence. (Auth.)

Using random response input in Ibrahim Time Domain

DEFF Research Database (Denmark)

Olsen, Peter; Brincker, R.

2013-01-01

In this paper the time domain technique Ibrahim Time Domain (ITD) is used to analyze random time data. ITD is known to be a technique for identification of output only systems. The traditional formulation of ITD is claimed to be limited, when identifying closely spaced modes, because....... In this article it is showed that when using the modified ITD random time data can be analyzed. The application of the technique is displayed by a case study, with simulations and experimental data....... of the technique being Single Input Multiple Output (SIMO). It has earlier been showed that when modifying ITD with Toeplitz matrix averaging. Identification of time data with closely spaced modes is improved. In the traditional formulation of ITD the time data has to be free decays or impulse response functions...

High-time resolution conjugate SuperDARN radar observations of the dayside convection response to changes in IMF By

Directory of Open Access Journals (Sweden)

G. Chisham

2000-02-01

Full Text Available We present data from conjugate SuperDARN radars describing the high-latitude ionosphere's response to changes in the direction of IMF By during a period of steady IMF Bz southward and Bx positive. During this interval, the radars were operating in a special mode which gave high-time resolution data (30 s sampling period on three adjacent beams with a full scan every 3 min. The location of the radars around magnetic local noon at the time of the event allowed detailed observations of the variations in the ionospheric convection patterns close to the cusp region as IMF By varied. A significant time delay was observed in the ionospheric response to the IMF By changes between the two hemispheres. This is explained as being partially a consequence of the location of the dominant merging region on the magnetopause, which is ~8-12RE closer to the northern ionosphere than to the southern ionosphere (along the magnetic field line due to the dipole tilt of the magnetosphere and the orientation of the IMF. This interpretation supports the anti-parallel merging hypothesis and highlights the importance of the IMF Bx component in solar wind-magnetosphere coupling.Key words: Ionosphere (plasma convection - Magnetospheric physics (magnetopause, cusp, and boundary layers; solar wind - magnetosphere interactions

Universal and local time components in Schumann resonance intensity

Directory of Open Access Journals (Sweden)

A. P. Nickolaenko

2008-05-01

Full Text Available We extend the technique suggested by Sentman and Fraser (1991 and discussed by Pechony and Price (2006, the technique for separating the local and universal time variations in the Schumann resonance intensity. Initially, we simulate the resonance oscillations in a uniform Earth-ionosphere cavity with the distribution of lightning strokes based on the OTD satellite data. Different field components were used in the Dayside source model for the Moshiri (Japan, geographic coordinates: 44.365° N, 142.24° E and Lehta (Karelia, Russia, 64.427° N, 33.974° E observatories. We use the extended Fourier series for obtaining the modulating functions. Simulations show that the algorithm evaluates the impact of the source proximity in the resonance intensity. Our major goal was in estimating the universal alteration factors, which reflect changes in the global thunderstorm activity. It was achieved by compensating the local factors present in the initial data. The technique is introduced with the model Schumann resonance data and afterwards we use the long-term experimental records at the above sites for obtaining the diurnal/monthly variations of the global thunderstorms.

Middle components of the auditory evoked response in bilateral temporal lobe lesions. Report on a patient with auditory agnosia

DEFF Research Database (Denmark)

Parving, A; Salomon, G; Elberling, Claus

1980-01-01

An investigation of the middle components of the auditory evoked response (10--50 msec post-stimulus) in a patient with auditory agnosia is reported. Bilateral temporal lobe infarctions were proved by means of brain scintigraphy, CAT scanning, and regional cerebral blood flow measurements...

RACLETTE: a model for evaluating the thermal response of plasma facing components to slow high power plasma transients. Part I: Theory and description of model capabilities

Science.gov (United States)

Raffray, A. René; Federici, Gianfranco

1997-04-01

RACLETTE (Rate Analysis Code for pLasma Energy Transfer Transient Evaluation), a comprehensive but relatively simple and versatile model, was developed to help in the design analysis of plasma facing components (PFCs) under 'slow' high power transients, such as those associated with plasma vertical displacement events. The model includes all the key surface heat transfer processes such as evaporation, melting, and radiation, and their interaction with the PFC block thermal response and the coolant behaviour. This paper represents part I of two sister and complementary papers. It covers the model description, calibration and validation, and presents a number of parametric analyses shedding light on and identifying trends in the PFC armour block response to high plasma energy deposition transients. Parameters investigated include the plasma energy density and deposition time, the armour thickness and the presence of vapour shielding effects. Part II of the paper focuses on specific design analyses of ITER plasma facing components (divertor, limiter, primary first wall and baffle), including improvements in the thermal-hydraulic modeling required for better understanding the consequences of high energy deposition transients in particular for the ITER limiter case.

RACLETTE: a model for evaluating the thermal response of plasma facing components to slow high power plasma transients. Pt. I. Theory and description of model capabilities

International Nuclear Information System (INIS)

Raffray, A.R.; Federici, G.

1997-01-01

For pt.II see ibid., p.101-30, 1997. RACLETTE (Rate Analysis Code for pLasma Energy Transfer Transient Evaluation), a comprehensive but relatively simple and versatile model, was developed to help in the design analysis of plasma facing components (PFCs) under 'slow' high power transients, such as those associated with plasma vertical displacement events. The model includes all the key surface heat transfer processes such as evaporation, melting, and radiation, and their interaction with the PFC block thermal response and the coolant behaviour. This paper represents part I of two sister and complementary papers. It covers the model description, calibration and validation, and presents a number of parametric analyses shedding light on and identifying trends in the PFC armour block response to high plasma energy deposition transients. Parameters investigated include the plasma energy density and deposition time, the armour thickness and the presence of vapour shielding effects. Part II of the paper focuses on specific design analyses of ITER plasma facing components (divertor, limiter, primary first wall and baffle), including improvements in the thermal-hydraulic modeling required for better understanding the consequences of high energy deposition transients in particular for the ITER limiter case. (orig.)

Brain response during the M170 time interval is sensitive to socially relevant information.

Science.gov (United States)

Arviv, Oshrit; Goldstein, Abraham; Weeting, Janine C; Becker, Eni S; Lange, Wolf-Gero; Gilboa-Schechtman, Eva

2015-11-01

Deciphering the social meaning of facial displays is a highly complex neurological process. The M170, an event related field component of MEG recording, like its EEG counterpart N170, was repeatedly shown to be associated with structural encoding of faces. However, the scope of information encoded during the M170 time window is still being debated. We investigated the neuronal origin of facial processing of integrated social rank cues (SRCs) and emotional facial expressions (EFEs) during the M170 time interval. Participants viewed integrated facial displays of emotion (happy, angry, neutral) and SRCs (indicated by upward, downward, or straight head tilts). We found that the activity during the M170 time window is sensitive to both EFEs and SRCs. Specifically, highly prominent activation was observed in response to SRC connoting dominance as compared to submissive or egalitarian head cues. Interestingly, the processing of EFEs and SRCs appeared to rely on different circuitry. Our findings suggest that vertical head tilts are processed not only for their sheer structural variance, but as social information. Exploring the temporal unfolding and brain localization of non-verbal cues processing may assist in understanding the functioning of the social rank biobehavioral system. Copyright © 2015 Elsevier Ltd. All rights reserved.

Reliability for systems of degrading components with distinct component shock sets

International Nuclear Information System (INIS)

Song, Sanling; Coit, David W.; Feng, Qianmei

2014-01-01

This paper studies reliability for multi-component systems subject to dependent competing risks of degradation wear and random shocks, with distinct shock sets. In practice, many systems are exposed to distinct and different types of shocks that can be categorized according to their sizes, function, affected components, etc. Previous research primarily focuses on simple systems with independent failure processes, systems with independent component time-to-failure, or components that share the same shock set or type of shocks. In our new model, we classify random shocks into different sets based on their sizes or function. Shocks with specific sizes or function can selectively affect one or more components in the system but not necessarily all components. Additionally the shocks from the different shock sets can arrive at different rates and have different relative magnitudes. Preventive maintenance (PM) optimization is conducted for the system with different component shock sets. Decision variables for two different maintenance scheduling problems, the PM replacement time interval, and the PM inspection time interval, are determined by minimizing a defined system cost rate. Sensitivity analysis is performed to provide insight into the behavior of the proposed maintenance policies. These models can be applied directly or customized for many complex systems that experience dependent competing failure processes with different component shock sets. A MEMS (Micro-electro mechanical systems) oscillator is a typical system subject to dependent and competing failure processes, and it is used as a numerical example to illustrate our new reliability and maintenance models

A discrimination-association model for decomposing component processes of the implicit association test.

Science.gov (United States)

Stefanutti, Luca; Robusto, Egidio; Vianello, Michelangelo; Anselmi, Pasquale

2013-06-01

A formal model is proposed that decomposes the implicit association test (IAT) effect into three process components: stimuli discrimination, automatic association, and termination criterion. Both response accuracy and reaction time are considered. Four independent and parallel Poisson processes, one for each of the four label categories of the IAT, are assumed. The model parameters are the rate at which information accrues on the counter of each process and the amount of information that is needed before a response is given. The aim of this study is to present the model and an illustrative application in which the process components of a Coca-Pepsi IAT are decomposed.

Impact of insufficient energy content in the design time history on the structure response

International Nuclear Information System (INIS)

Ma, D.C.; Gvildys, J.; Chang, Y.W.; Seidensticker, R.W.

1989-01-01

In the design of nuclear power plants, it is often desirable to use the time history method in the soil-structure interaction analysis to determine the plant floor response to seismic loads. Because many design criteria are specified in terms of design response spectra, the artificial time history needs to be generated under the requirement that the response spectra of the artificial history should envelop the given design response spectra. However, recent studies indicate that the artificial time history used in the plant design may have insufficient energy in the frequency range of interest, even though the response spectra of the design time history closely envelop the design response spectra. Therefore, the proposed changes in the NRC Standard Review Plan requires that when a single time history is used in the seismic design, it must satisfy requirements for both response spectra enveloping and matching a power spectra density (PSD) function in the frequency range of interest. The use of multiple artificial time histories (at least five time histories) in the plant design is also suggested in the new Standard Review Plan. This paper presents an investigation of the effects of the insufficient energy content in the design time history on the response of the soil-structure system. Numerical studies were carried out. Both the real earthquake records and the artificial time histories were used as the input motions in a simple lumped-mass soil-structure interaction model. The results obtained from this study provide a better understanding of the effects of the insufficient energy content in the design time history on the structural response. 5 refs., 10 figs., 1 tab

Knowing where is different from knowing what: Distinct response time profiles and accuracy effects for target location, orientation, and color probability.

Science.gov (United States)

Jabar, Syaheed B; Filipowicz, Alex; Anderson, Britt

2017-11-01

When a location is cued, targets appearing at that location are detected more quickly. When a target feature is cued, targets bearing that feature are detected more quickly. These attentional cueing effects are only superficially similar. More detailed analyses find distinct temporal and accuracy profiles for the two different types of cues. This pattern parallels work with probability manipulations, where both feature and spatial probability are known to affect detection accuracy and reaction times. However, little has been done by way of comparing these effects. Are probability manipulations on space and features distinct? In a series of five experiments, we systematically varied spatial probability and feature probability along two dimensions (orientation or color). In addition, we decomposed response times into initiation and movement components. Targets appearing at the probable location were reported more quickly and more accurately regardless of whether the report was based on orientation or color. On the other hand, when either color probability or orientation probability was manipulated, response time and accuracy improvements were specific for that probable feature dimension. Decomposition of the response time benefits demonstrated that spatial probability only affected initiation times, whereas manipulations of feature probability affected both initiation and movement times. As detection was made more difficult, the two effects further diverged, with spatial probability disproportionally affecting initiation times and feature probability disproportionately affecting accuracy. In conclusion, all manipulations of probability, whether spatial or featural, affect detection. However, only feature probability affects perceptual precision, and precision effects are specific to the probable attribute.

Beta-lipotropin is the major component of the plasma opioid response to surgical stress in humans

Energy Technology Data Exchange (ETDEWEB)

Porro, C.A.; Facchinetti, F.; Bertellini, E.; Petraglia, F.; Stacca, R.; Barbieri, G.C.; Genazzani, A.R.

1987-12-07

There is growing experimental evidence that beta-endorphin immunoreactivity is raised by surgical stress in patients undergoing general anesthesia. As the assay methods employed to date did not allow to fully discriminate between beta-endorphin and its immediate precursor, beta-lipotropin, the authors have investigated in the present study plasma levels of these two peptides by separating them by chromatography on plasma extracts prior to radioimmunoassay. Beta-lipotropin, but not beta-endorphin, plasma levels were found to be significantly elevated during surgery in the general anesthesia group, while no change was found in either peptide concentration in the spinal one. Cortisol plasma levels also increased significantly 90 minutes after the beginning of surgery. Although the sampling time they adopted may have prevented them from detecting an early peak of beta-endorphin during the first 30 minutes of surgery, the major component of the pituitary opioid response to surgical stress appears to be related to beta-lipotropin. This is in agreement with results of experimental work on various kinds of stress in animals and humans and seems to rule out a role for plasma beta-endorphin in post-operative analgesia. 38 references, 1 figure, 1 table.

Psychophysical and physiological responses to gratings with luminance and chromatic components of different spatial frequencies.

Science.gov (United States)

Cooper, Bonnie; Sun, Hao; Lee, Barry B

2012-02-01

Gratings that contain luminance and chromatic components of different spatial frequencies were used to study the segregation of signals in luminance and chromatic pathways. Psychophysical detection and discrimination thresholds to these compound gratings, with luminance and chromatic components of the one either half or double the spatial frequency of the other, were measured in human observers. Spatial frequency tuning curves for detection of compound gratings followed the envelope of those for luminance and chromatic gratings. Different grating types were discriminable at detection threshold. Fourier analysis of physiological responses of macaque retinal ganglion cells to compound waveforms showed chromatic information to be restricted to the parvocellular pathway and luminance information to the magnocellular pathway. Taken together, the human psychophysical and macaque physiological data support the strict segregation of luminance and chromatic information in independent channels, with the magnocellular and parvocellular pathways, respectively, serving as likely the physiological substrates. © 2012 Optical Society of America

A study on HCI design strategy using emergent features and response time

International Nuclear Information System (INIS)

Lee, Sung Jin; Chang, Soon Heung; Park, Jin Gyun

2001-01-01

Existing design process of user interface has some weak point that there is no feedback information and no quantitative information between each sub process. If they're such information in design process, the design time cycle will be decreased and the contentment of HCI in the aspect of user will be more easily archived. In this study, new design process with feedback information and quantitative information was proposed using emergent features and user response time. The proposed methodology was put together with three main parts. First part is to calculate distinctiveness of a user interface or expanded user interface with consideration of emergent features. Second part is to expand a prototype user interface with design option for purpose of design requirement using directed structure graph (or nodal graph) theory. Last part is to convert non-realized value, distinctiveness, into realized value, response time, by response time database or response time correlation in the form of Hick-Hyman law equation. From the present validations, the usefulness of the proposed methodology was obtained by simple validation testing. It was found that emergent features should be improved for high reflection of real user interface. For the reliability of response time database, lots of end-user experiment is necessary. Expansion algorithm and representation technique of qualitative information should be somewhat improved for more efficient design process

Radiation dose response correlation between thermoluminescence and optically stimulated luminescence in quartz

International Nuclear Information System (INIS)

Oniya, E.O.; Polymeris, G.S.; Tsirliganis, N.C.; Kitis, G.

2012-01-01

The fast, linearly modulated optically stimulated luminescence (LM-OSL) component in quartz is the main dosimetric signal used for the dating applications of this material. Since the blue light stimulation (470 nm, 40 mW cm −2 ) time needed to obtain the fast LM-OSL component is less than 50 s the electron trapping levels responsible for it are still highly populated. In this way an active radiation history is created which could play an important role in the dosimetric characteristics of the fast OSL signal. In the present work the dose response behavior of the fast OSL signal is investigated in quartz samples with an annealed radiation history and quartz samples possessing an artificial radiation history. A computerized curve de-convolution analysis of the LM-OSL curves for 50 s stimulation time showed that it consists of three individual OSL components. The faster component C 1 with peak maximum time around 5 s has a linear dose response in virgin samples, which turns to a slight superlinearity as a function of the artificial radiation history. On the other hand the component C 2 with peak maximum time at 12 s is slightly superlinear which turns into strong superlinearity as a function of artificial radiation history. Finally, component C 3 with peak maximum time at about 45 s is strongly superlinear for both virgin samples and as a function of artificial radiation history. The implications to practical application are discussed. - Highlights: ► The fast OSL component consists of three components. ► The linearity of first fast component does not depend on radiation history. ► The linearity of second and third components depend on radiation history. ► The TL between 180 and 300 °C is the major source of OSL.

Bioelectric signal classification using a recurrent probabilistic neural network with time-series discriminant component analysis.

Science.gov (United States)

Hayashi, Hideaki; Shima, Keisuke; Shibanoki, Taro; Kurita, Yuichi; Tsuji, Toshio

2013-01-01

This paper outlines a probabilistic neural network developed on the basis of time-series discriminant component analysis (TSDCA) that can be used to classify high-dimensional time-series patterns. TSDCA involves the compression of high-dimensional time series into a lower-dimensional space using a set of orthogonal transformations and the calculation of posterior probabilities based on a continuous-density hidden Markov model that incorporates a Gaussian mixture model expressed in the reduced-dimensional space. The analysis can be incorporated into a neural network so that parameters can be obtained appropriately as network coefficients according to backpropagation-through-time-based training algorithm. The network is considered to enable high-accuracy classification of high-dimensional time-series patterns and to reduce the computation time taken for network training. In the experiments conducted during the study, the validity of the proposed network was demonstrated for EEG signals.

Photoconductivity response time in amorphous semiconductors

Science.gov (United States)

Adriaenssens, G. J.; Baranovskii, S. D.; Fuhs, W.; Jansen, J.; Öktü, Ö.

1995-04-01

The photoconductivity response time of amorphous semiconductors is examined theoretically on the basis of standard definitions for free- and trapped-carrier lifetimes, and experimentally for a series of a-Si1-xCx:H alloys with xgeneration rate and temperature. As no satisfactory agreement between models and experiments emerges, a simple theory is developed that can account for the experimental observations on the basis of the usual multiple-trappping ideas, provided a small probability of direct free-carrier recombination is included. The theory leads to a stretched-exponential photocurrent decay.

Time response analysis in suspension system design of a high-speed car

Science.gov (United States)

Pagwiwoko, Cosmas Pandit

2010-03-01

A land speed record vehicle is designed to run on a flat surface like salt lake where the wheels are normally made from solid metal with a special suspension system. The suspension is designed to provide a stable platform to keep the wheel treads on tract, to insulate the car and the driver from the surface irregularities and to take part of good handling properties. The surface condition of the lake beds is basically flat without undulations but with inconsistent surface textures and ridges. Spring with nonlinear rate is used with the reason that the resistance builds up roughly proportional to the aerodynamic download for keeping the height more nearly constant. The objective of the work is to produce an efficient method for assisting the design of suspension system. At the initial step, the stiffness and the damping constants are determined based on RMS optimization by following the optimization strategy i.e. to minimize the absolute acceleration respect to the relative displacement of the suspension. Power bond graph technique is then used to model the nonlinearity of the components i.e. spring and dashpot of the suspension system. This technique also enables to incorporate the interactions of dynamic response of the vehicle's body with aerodynamic flow as a result of the base excitation of the ground to the wheels. The simulation is conducted on the platform of Simulink-MATLAB and the interactions amongst the components within the system are observed in time domain to evaluate the effectiveness of the suspension.

Study on time response properties of ionization chamber in profile gauge

International Nuclear Information System (INIS)

Wang Zhentao; Shen Yixiong; Wang Liqiang; Hao Pengfei

2011-01-01

The drift time of ions in the ionization chamber was measured by means of using a shortly pulsed X-ray device and through analyzing the voltage signals on the load resistor of the chamber recorded by a digital oscilloscope. By using this method, the time response properties of the ionization chamber in the profile gauge were studied, results of ion drift time for ionization chambers with different internal structures, different voltages and different gas pressures were introduced and the sources of error were discussed. The experiment results show that the time response of ionization chamber in profile gauge meets the requirement of on-line hot strip measuring. (authors)

Review of resistance temperature detector time response characteristics. Safety evaluation report

International Nuclear Information System (INIS)

1981-08-01

A Resistance Temperature Detector (RTD) is used extensively for monitoring water temperatures in nuclear reactor plants. The RTD element does not respond instantaneously to changes in water temperature, but rather there is a time delay before the element senses the temperature change, and in nuclear reactors this delay must be factored into the computation of safety setpoints. For this reason it is necessary to have an accurate description of the RTD time response. This report is a review of the current state of the art of describing and measuring this time response

Performing dynamic time history analyses by extension of the response spectrum method

International Nuclear Information System (INIS)

Hulbert, G.M.

1983-01-01

A method is presented to calculate the dynamic time history response of finite-element models using results from response spectrum analyses. The proposed modified time history method does not represent a new mathamatical approach to dynamic analysis but suggests a more efficient ordering of the analytical equations and procedures. The modified time history method is considerably faster and less expensive to use than normal time hisory methods. This paper presents the theory and implementation of the modified time history approach along with comparisons of the modified and normal time history methods for a prototypic seismic piping design problem

48 CFR 5.203 - Publicizing and response time.

Science.gov (United States)

2010-10-01

... development if the proposed contract action is expected to exceed the simplified acquisition threshold. (f) Nothing in this subpart prohibits officers or employees of agencies from responding to requests for... response times specified in paragraphs (a) through (d) of this section. Upon learning that a particular...

A new method for measuring the response time of the high pressure ionization chamber

International Nuclear Information System (INIS)

Wang, Zhentao; Shen, Yixiong; An, Jigang

2012-01-01

Time response is an important performance characteristic for gas-pressurized ionization chambers. To study the time response, it is especially crucial to measure the ion drift time in high pressure ionization chambers. In this paper, a new approach is proposed to study the ion drift time in high pressure ionization chambers. It is carried out with a short-pulsed X-ray source and a high-speed digitizer. The ion drift time in the chamber is then determined from the digitized data. By measuring the ion drift time of a 15 atm xenon testing chamber, the method has been proven to be effective in the time response studies of ionization chambers. - Highlights: ► A method for measuring response time of high pressure ionization chamber is proposed. ► A pulsed X-ray producer and a digital oscilloscope are used in the method. ► The response time of a 15 atm Xenon testing ionization chamber has been measured. ► The method has been proved to be simple, feasible and effective.

On response time and cycle time distributions in a two-stage cyclic queue

NARCIS (Netherlands)

Boxma, O.J.; Donk, P.

1982-01-01

We consider a two-stage closed cyclic queueing model. For the case of an exponential server at each queue we derive the joint distribution of the successive response times of a custumer at both queues, using a reversibility argument. This joint distribution turns out to have a product form. The

Searching for serial refreshing in working memory: Using response times to track the content of the focus of attention over time.

Science.gov (United States)

Vergauwe, Evie; Hardman, Kyle O; Rouder, Jeffrey N; Roemer, Emily; McAllaster, Sara; Cowan, Nelson

2016-12-01

One popular idea is that, to support the maintenance of a set of elements over brief periods of time, the focus of attention rotates among the different elements, thereby serially refreshing the content of working memory (WM). In the research reported here, probe letters were presented between to-be-remembered letters, and response times to these probes were used to infer the status of the different items in WM. If the focus of attention cycles from one item to the next, its content should be different at different points in time, and this should be reflected in a change in the response time patterns over time. Across a set of four experiments, we demonstrated a striking pattern of invariance in the response time patterns over time, suggesting either that the content of the focus of attention did not change over time or that response times cannot be used to infer the content of the focus of attention. We discuss how this pattern constrains models of WM, attention, and human information processing.

Changes in the Social Responsibility Attitudes of Engineering Students Over Time.

Science.gov (United States)

Bielefeldt, Angela R; Canney, Nathan E

2016-10-01

This research explored how engineering student views of their responsibility toward helping individuals and society through their profession, so-called social responsibility, change over time. A survey instrument was administered to students initially primarily in their first year, senior year, or graduate studies majoring in mechanical, civil, or environmental engineering at five institutions in September 2012, April 2013, and March 2014. The majority of the students (57 %) did not change significantly in their social responsibility attitudes, but 23 % decreased and 20 % increased. The students who increased, decreased, or remained the same in their social responsibility attitudes over time did not differ significantly in terms of gender, academic rank, or major. Some differences were found between institutions. Students who decreased in social responsibility initially possessed more positive social responsibility attitudes, were less likely to indicate that college courses impacted their views of social responsibility, and were more likely to have decreased in the frequency that they participated in volunteer activities, compared to students who did not change or increased their social responsibility. Although the large percentage of engineering students who decreased their social responsibility during college was disappointing, it is encouraging that courses and participation in volunteer activities may combat this trend.

Optimal time interval for induction of immunologic adaptive response

International Nuclear Information System (INIS)

Ju Guizhi; Song Chunhua; Liu Shuzheng

1994-01-01

The optimal time interval between prior dose (D1) and challenge dose (D2) for the induction of immunologic adaptive response was investigated. Kunming mice were exposed to 75 mGy X-rays at a dose rate of 12.5 mGy/min. 3, 6, 12, 24 or 60 h after the prior irradiation the mice were challenged with a dose of 1.5 Gy at a dose rate of 0.33 Gy/min. 18h after D2, the mice were sacrificed for examination of immunological parameters. The results showed that with an interval of 6 h between D1 and D2, the adaptive response of the reaction of splenocytes to LPS was induced, and with an interval of 12 h the adaptive responses of spontaneous incorporation of 3 H-TdR into thymocytes and the reaction of splenocytes to Con A and LPS were induced with 75 mGy prior irradiation. The data suggested that the optimal time intervals between D1 and D2 for the induction of immunologic adaptive response were 6 h and 12 h with a D1 of 75 mGy and a D2 of 1.5 Gy. The mechanism of immunologic adaptation following low dose radiation is discussed

A first application of independent component analysis to extracting structure from stock returns.

Science.gov (United States)

Back, A D; Weigend, A S

1997-08-01

This paper explores the application of a signal processing technique known as independent component analysis (ICA) or blind source separation to multivariate financial time series such as a portfolio of stocks. The key idea of ICA is to linearly map the observed multivariate time series into a new space of statistically independent components (ICs). We apply ICA to three years of daily returns of the 28 largest Japanese stocks and compare the results with those obtained using principal component analysis. The results indicate that the estimated ICs fall into two categories, (i) infrequent large shocks (responsible for the major changes in the stock prices), and (ii) frequent smaller fluctuations (contributing little to the overall level of the stocks). We show that the overall stock price can be reconstructed surprisingly well by using a small number of thresholded weighted ICs. In contrast, when using shocks derived from principal components instead of independent components, the reconstructed price is less similar to the original one. ICA is shown to be a potentially powerful method of analyzing and understanding driving mechanisms in financial time series. The application to portfolio optimization is described in Chin and Weigend (1998).

A Fault Prognosis Strategy Based on Time-Delayed Digraph Model and Principal Component Analysis

Directory of Open Access Journals (Sweden)

Ningyun Lu

2012-01-01

Full Text Available Because of the interlinking of process equipments in process industry, event information may propagate through the plant and affect a lot of downstream process variables. Specifying the causality and estimating the time delays among process variables are critically important for data-driven fault prognosis. They are not only helpful to find the root cause when a plant-wide disturbance occurs, but to reveal the evolution of an abnormal event propagating through the plant. This paper concerns with the information flow directionality and time-delay estimation problems in process industry and presents an information synchronization technique to assist fault prognosis. Time-delayed mutual information (TDMI is used for both causality analysis and time-delay estimation. To represent causality structure of high-dimensional process variables, a time-delayed signed digraph (TD-SDG model is developed. Then, a general fault prognosis strategy is developed based on the TD-SDG model and principle component analysis (PCA. The proposed method is applied to an air separation unit and has achieved satisfying results in predicting the frequently occurred “nitrogen-block” fault.

Locating AED Enabled Medical Drones to Enhance Cardiac Arrest Response Times.

Science.gov (United States)

Pulver, Aaron; Wei, Ran; Mann, Clay

2016-01-01

Out-of-hospital cardiac arrest (OOHCA) is prevalent in the United States. Each year between 180,000 and 400,000 people die due to cardiac arrest. The automated external defibrillator (AED) has greatly enhanced survival rates for OOHCA. However, one of the important components of successful cardiac arrest treatment is emergency medical services (EMS) response time (i.e., the time from EMS "wheels rolling" until arrival at the OOHCA scene). Unmanned Aerial Vehicles (UAV) have regularly been used for remote sensing and aerial imagery collection, but there are new opportunities to use drones for medical emergencies. The purpose of this study is to develop a geographic approach to the placement of a network of medical drones, equipped with an automated external defibrillator, designed to minimize travel time to victims of out-of-hospital cardiac arrest. Our goal was to have one drone on scene within one minute for at least 90% of demand for AED shock therapy, while minimizing implementation costs. In our study, the current estimated travel times were evaluated in Salt Lake County using geographical information systems (GIS) and compared to the estimated travel times of a network of AED enabled medical drones. We employed a location model, the Maximum Coverage Location Problem (MCLP), to determine the best configuration of drones to increase service coverage within one minute. We found that, using traditional vehicles, only 4.3% of the demand can be reached (travel time) within one minute utilizing current EMS agency locations, while 96.4% of demand can be reached within five minutes using current EMS vehicles and facility locations. Analyses show that using existing EMS stations to launch drones resulted in 80.1% of cardiac arrest demand being reached within one minute Allowing new sites to launch drones resulted in 90.3% of demand being reached within one minute. Finally, using existing EMS and new sites resulted in 90.3% of demand being reached while greatly reducing

Acute Anxiety Predicts Components of the Cold Shock Response on Cold Water Immersion: Toward an Integrated Psychophysiological Model of Acute Cold Water Survival

Science.gov (United States)

Barwood, Martin J.; Corbett, Jo; Massey, Heather; McMorris, Terry; Tipton, Mike; Wagstaff, Christopher R. D.

2018-01-01

Introduction: Drowning is a leading cause of accidental death. In cold-water, sudden skin cooling triggers the life-threatening cold shock response (CSR). The CSR comprises tachycardia, peripheral vasoconstriction, hypertension, inspiratory gasp, and hyperventilation with the hyperventilatory component inducing hypocapnia and increasing risk of aspirating water to the lungs. Some CSR components can be reduced by habituation (i.e., reduced response to stimulus of same magnitude) induced by 3–5 short cold-water immersions (CWI). However, high levels of acute anxiety, a plausible emotion on CWI: magnifies the CSR in unhabituated participants, reverses habituated components of the CSR and prevents/delays habituation when high levels of anxiety are experienced concurrent to immersions suggesting anxiety is integral to the CSR. Purpose: To examine the predictive relationship that prior ratings of acute anxiety have with the CSR. Secondly, to examine whether anxiety ratings correlated with components of the CSR during immersion before and after induction of habituation. Methods: Forty-eight unhabituated participants completed one (CON1) 7-min immersion in to cold water (15°C). Of that cohort, twenty-five completed four further CWIs that would ordinarily induce CSR habituation. They then completed two counter-balanced immersions where anxiety levels were increased (CWI-ANX) or were not manipulated (CON2). Acute anxiety and the cardiorespiratory responses (cardiac frequency [fc], respiratory frequency [fR], tidal volume [VT], minute ventilation [E]) were measured. Multiple regression was used to identify components of the CSR from the most life-threatening period of immersion (1st minute) predicted by the anxiety rating prior to immersion. Relationships between anxiety rating and CSR components during immersion were assessed by correlation. Results: Anxiety rating predicted the fc component of the CSR in unhabituated participants (CON1; p anxiety rating predicted the f

Saproxylic community, guild and species responses to varying pheromone components of a pine bark beetle.

Science.gov (United States)

Etxebeste, Iñaki; Lencina, José L; Pajares, Juan

2013-10-01

Some bark beetle species (Coleoptera: Scolytinae) produce aggregation pheromones that allow coordinated attack on their conifer hosts. As a new saproxylic habitat is founded, an assemblage of associated beetles kairomonally respond to bark beetle infochemicals. Ips sexdentatus is one of the major damaging insects of Pinus spp. in Southern Europe. Its response to varying ipsenol (Ie) percentages in relation to ipsdienol (Id) was studied in northwestern Spain, along with the entire saproxylic beetle assemblage captured at multiple-funnel traps. Response profile modeling was undertaken for I. sexdentatus sexes and sex-ratios, associated species and for selected trophic groups using a reference Gaussian model. In addition, the effects on the saproxylic assemblages were analyzed. I. sexdentatus response curve peaked at 22.7% Ie content, while remaining taxa that could be modeled, peaked above ca. 40% Ie. Predator guilds showed a linear relationship with Ie proportion, while competitors showed a delayed response peak. Consequently, species assemblages differed markedly between varying pheromone component mixtures. Given that the evaluated pheromonal proportions mimicked that of logs being colonized by I. sexdentatus, results suggested that the registered differential responses at different levels might provide I. sexdentatus with a temporal window that maximizes conspecific attraction while reducing interference with competitor and predatory guilds. Described responses might help improve the monitoring of the population status of target bark beetles and their associates, but also point toward the by-catch of many natural enemies, as well as rare saproxylic beetle species, interfering with the aims of sustainable forest management.

Effects of aging on calibration and response time of nuclear plant pressure transmitters

International Nuclear Information System (INIS)

Hashemian, H.M.

1991-01-01

This paper presents the key results of an experimental research project conducted for the Nuclear Regulatory Commission to quantify the effects of normal aging on static and dynamic performance of nuclear grade pressure, level, and flow transmitters (hereafter referred to as pressure transmitters). The project involved laboratory testing of representative pressure transmitters manufactured by Barton, Foxboro, Rosemount, and Tobar (or Veritrak) companies. These manufacturers provide the four most commonly used pressure transmitters in the safety systems of US nuclear power plants. The transmitters were tested under normal aging conditions as opposed to accelerated aging, even though accelerated aging will be used in the last few months of the project to determine the weak links and failure modes of the transmitters. The project has been performed in two phases. The Phase 1 project which was a six month feasibility study has been completed and the results published in NUREG/CR-5383. The Phase 2 project is still underway with the final report due in the fall of 1991. The project has focused on the following areas: (1) effects of aging on calibration stability; (2) effects of aging on response time; (3) study of individual components of pressure transmitters that are sensitive to aging degradation; (4) sensing line blockages due to solidification of boron, formation of sludge, freezing, and other effects; (5) search of licensee event reports and component reliability databases for failures of safety-related pressure transmitters; and (6) oil loss syndrome in Rosemount pressure transmitters

Application of Response Surface Methodology in Extraction of Bioactive Component from Palm Leaves (Elaeis guineensis

Directory of Open Access Journals (Sweden)

Nur Afiqah Arham

2013-10-01

Full Text Available Normal 0 false false false IN X-NONE X-NONE MicrosoftInternetExplorer4 The hydroxyl groups of the polyphenols are capable to act as reducing agent for reduction reaction. The effect of drying temperature, extraction temperature and extraction duration were evaluated using central composite design which consists of 20 experimental runs. Response surface methodology (RSM was used to estimate the optimum parameters in extracting polyphenols from the palm leaves. The correspondence analysis of the results yielded a quadratic model which can be used to find optimum conditions of extraction process. The optimum extraction condition of drying temperature, extraction temperature and extraction duration are 70°C, at 70°C of 10 minutes, respectively. Total polyphenols were determined by application of the Folin-Ciocalteu micro method and the extract was found contain of 8 mg GAE/g dry palm leaves at optimum conditions. Normal 0 false false false IN X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} Doi: 10.12777/ijse.5.2.95-100 [How to cite this article: Arham, N.A., Mohamad, N.A.N., Jai, J., Krishnan, J., Noorsuhana Mohd Yusof, N.M. (2013. Application of Response Surface Methodology in Extraction of Bioactive Component from Palm Leaves (Elaeis guineensis. International Journal of Science and

Response Times of Operators in a Control Room

DEFF Research Database (Denmark)

Platz, O.; Rasmussen, Jens; Skanborg, Preben Zacho

A statistical analysis was made of operator response times recorded in the control room of a research reactor during the years 1972-1974. A homogeneity test revealed that the data consist of a mixture of populations. A small but statistically significant difference is found between day and night...

A data analysis method for identifying deterministic components of stable and unstable time-delayed systems with colored noise

Energy Technology Data Exchange (ETDEWEB)

Patanarapeelert, K. [Faculty of Science, Department of Mathematics, Mahidol University, Rama VI Road, Bangkok 10400 (Thailand); Frank, T.D. [Institute for Theoretical Physics, University of Muenster, Wilhelm-Klemm-Str. 9, 48149 Muenster (Germany)]. E-mail: tdfrank@uni-muenster.de; Friedrich, R. [Institute for Theoretical Physics, University of Muenster, Wilhelm-Klemm-Str. 9, 48149 Muenster (Germany); Beek, P.J. [Faculty of Human Movement Sciences and Institute for Fundamental and Clinical Human Movement Sciences, Vrije Universiteit, Van der Boechorststraat 9, 1081 BT Amsterdam (Netherlands); Tang, I.M. [Faculty of Science, Department of Physics, Mahidol University, Rama VI Road, Bangkok 10400 (Thailand)

2006-12-18

A method is proposed to identify deterministic components of stable and unstable time-delayed systems subjected to noise sources with finite correlation times (colored noise). Both neutral and retarded delay systems are considered. For vanishing correlation times it is shown how to determine their noise amplitudes by minimizing appropriately defined Kullback measures. The method is illustrated by applying it to simulated data from stochastic time-delayed systems representing delay-induced bifurcations, postural sway and ship rolling.

Development of a geometry-compensated neutron time-of-flight detector for ICF applications with approximately 200 ps time response

International Nuclear Information System (INIS)

Murphy, T.J.; Lerche, R.A.

1992-01-01

Current-mode neutron time-of-flight detectors are used on Nova for neutron yield, ion temperature, and neutron emission time measurements. Currently used detectors are limited by the time response of the microchannel plate photomultiplier tubes used with the scintillators, scintillator decay time, scintillator thickness, and oscilloscope response time. A change in the geometry of the scintillator allows one to take advantage of the increased time resolution made possible by more advanced transient recorders and microchannel plate photomultiplier tubes. A prototype detector has been designed to incorporate these changes, and could potentially yield time resolution of less than 150 ps. Experimental results are presented demonstrating an ion temperature measurement of a direct-drive DT implosion on Nova

Electromagnet Response Time Tests on Primary CRDM of a Prototype Gen-IV SFR

International Nuclear Information System (INIS)

Lee, Jae-Han; Koo, Gyeong-Hoi

2015-01-01

This paper identifies the electromagnetic response characteristics of the electromagnet of a primary control rod drive mechanism (CRDM) used for the reactor scram function. The test measures the electromagnet response time required to release an armature from a stator controlled by a loss of an electromagnetic force on an armature after shorting a power supply to an electromagnet coil. These tests are carried out while changing the electromagnet core material, an assist spring, and an armature holding current. The main factors influencing the test parameters on the response are found to be the armature holding current for holding the armature loads, and the material type of the electromagnet cores. The minimum response time is 0.13 seconds in the case of using SS410 material as an armature, while the S10C material as an armature has a response time of 0.21 seconds. Electromagnet response time characteristics from the test results will be evaluated by comparing the precise moving data of an electromagnet armature through the use of a high-speed camera and a potentiometer in the future

Time history nonlinear earthquake response analysis considering materials and geometrical nonlinearity

International Nuclear Information System (INIS)

Kobayashi, T.; Yoshikawa, K.; Takaoka, E.; Nakazawa, M.; Shikama, Y.

2002-01-01

A time history nonlinear earthquake response analysis method was proposed and applied to earthquake response prediction analysis for a Large Scale Seismic Test (LSST) Program in Hualien, Taiwan, in which a 1/4 scale model of a nuclear reactor containment structure was constructed on sandy gravel layer. In the analysis both of strain-dependent material nonlinearity, and geometrical nonlinearity by base mat uplift, were considered. The 'Lattice Model' for the soil-structure interaction model was employed. An earthquake record on soil surface at the site was used as control motion, and deconvoluted to the input motion of the analysis model at GL-52 m with 300 Gal of maximum acceleration. The following two analyses were considered: (A) time history nonlinear, (B) equivalent linear, and the advantage of time history nonlinear earthquake response analysis method is discussed

Perceived Synchrony of Frog Multimodal Signal Components Is Influenced by Content and Order.

Science.gov (United States)

Taylor, Ryan C; Page, Rachel A; Klein, Barrett A; Ryan, Michael J; Hunter, Kimberly L

2017-10-01

Multimodal signaling is common in communication systems. Depending on the species, individual signal components may be produced synchronously as a result of physiological constraint (fixed) or each component may be produced independently (fluid) in time. For animals that rely on fixed signals, a basic prediction is that asynchrony between the components should degrade the perception of signal salience, reducing receiver response. Male túngara frogs, Physalaemus pustulosus, produce a fixed multisensory courtship signal by vocalizing with two call components (whines and chucks) and inflating a vocal sac (visual component). Using a robotic frog, we tested female responses to variation in the temporal arrangement between acoustic and visual components. When the visual component lagged a complex call (whine + chuck), females largely rejected this asynchronous multisensory signal in favor of the complex call absent the visual cue. When the chuck component was removed from one call, but the robofrog inflation lagged the complex call, females responded strongly to the asynchronous multimodal signal. When the chuck component was removed from both calls, females reversed preference and responded positively to the asynchronous multisensory signal. When the visual component preceded the call, females responded as often to the multimodal signal as to the call alone. These data show that asynchrony of a normally fixed signal does reduce receiver responsiveness. The magnitude and overall response, however, depend on specific temporal interactions between the acoustic and visual components. The sensitivity of túngara frogs to lagging visual cues, but not leading ones, and the influence of acoustic signal content on the perception of visual asynchrony is similar to those reported in human psychophysics literature. Virtually all acoustically communicating animals must conduct auditory scene analyses and identify the source of signals. Our data suggest that some basic

Consumer responses to time varying prices for electricity

International Nuclear Information System (INIS)

Thorsnes, Paul; Williams, John; Lawson, Rob

2012-01-01

We report new experimental evidence of the household response to weekday differentials in peak and off-peak electricity prices. The data come from Auckland, New Zealand, where peak residential electricity consumption occurs in winter for heating. Peak/off-peak price differentials ranged over four randomly selected groups from 1.0 to 3.5. On average, there was no response except in winter. In winter, participant households reduced electricity consumption by at least 10%, took advantage of lower off-peak prices but did not respond to the peak price differentials. Response varied with house and household size, time spent away from home, and whether water was heated with electricity. - Highlights: ► Seasonal effects in winter. ► High conservation effect from information. ► Higher peak prices no effect on peak use. ► Low off-peak prices encourage less conservation off-peak.

Analytical Call Center Model with Voice Response Unit and Wrap-Up Time

Directory of Open Access Journals (Sweden)

Petr Hampl

2015-01-01

Full Text Available The last twenty years of computer integration significantly changed the process of service in a call center service systems. Basic building modules of classical call centers – a switching system and a group of humans agents – was extended with other special modules such as skills-based routing module, automatic call distribution module, interactive voice response module and others to minimize the customer waiting time and wage costs. A calling customer of a modern call center is served in the first stage by the interactive voice response module without any human interaction. If the customer requirements are not satisfied in the first stage, the service continues to the second stage realized by the group of human agents. The service time of second stage – the average handle time – is divided into a conversation time and wrap-up time. During the conversation time, the agent answers customer questions and collects its requirements and during the wrap-up time (administrative time the agent completes the task without any customer interaction. The analytical model presented in this contribution is solved under the condition of statistical equilibrium and takes into account the interactive voice response module service time, the conversation time and the wrap-up time.

Comparative study of on-line response time measurement methods for platinum resistance thermometer

International Nuclear Information System (INIS)

Zwingelstein, G.; Gopal, R.

1979-01-01

This study deals with the in site determination of the response time of platinum resistance sensor. In the first part of this work, two methods furnishing the reference response time of the sensors are studied. In the second part of the work, two methods obtaining the response time without dismounting of the sensor, are studied. A comparative study of the performances of these methods is included for fluid velocities varying from 0 to 10 m/sec, in both laboratory and plant conditions

Differential gene expression profiling of mouse skin after sulfur mustard exposure: Extended time response and inhibitor effect

International Nuclear Information System (INIS)

Gerecke, Donald R.; Chen Minjun; Isukapalli, Sastry S.; Gordon, Marion K.; Chang, Y.-C.; Tong Weida; Androulakis, Ioannis P.; Georgopoulos, Panos G.

2009-01-01

Sulfur mustard (HD, SM), is a chemical warfare agent that within hours causes extensive blistering at the dermal-epidermal junction of skin. To better understand the progression of SM-induced blistering, gene expression profiling for mouse skin was performed after a single high dose of SM exposure. Punch biopsies of mouse ears were collected at both early and late time periods following SM exposure (previous studies only considered early time periods). The biopsies were examined for pathological disturbances and the samples further assayed for gene expression profiling using the Affymetrix microarray analysis system. Principal component analysis and hierarchical cluster analysis of the differently expressed genes, performed with ArrayTrack showed clear separation of the various groups. Pathway analysis employing the KEGG library and Ingenuity Pathway Analysis (IPA) indicated that cytokine-cytokine receptor interaction, cell adhesion molecules (CAMs), and hematopoietic cell lineage are common pathways affected at different time points. Gene ontology analysis identified the most significantly altered biological processes as the immune response, inflammatory response, and chemotaxis; these findings are consistent with other reported results for shorter time periods. Selected genes were chosen for RT-PCR verification and showed correlations in the general trends for the microarrays. Interleukin 1 beta was checked for biological analysis to confirm the presence of protein correlated to the corresponding microarray data. The impact of a matrix metalloproteinase inhibitor, MMP-2/MMP-9 inhibitor I, against SM exposure was assessed. These results can help in understanding the molecular mechanism of SM-induced blistering, as well as to test the efficacy of different inhibitors

Practical aspects of estimating energy components in rodents

Directory of Open Access Journals (Sweden)

Jan Bert evan Klinken

2013-05-01

Full Text Available Recently there has been an increasing interest in exploiting computational and statistical techniques for the purpose of component analysis of indirect calorimetry data. Using these methods it becomes possible to dissect daily energy expenditure into its components and to assess the dynamic response of the resting metabolic rate to nutritional and pharmacological manipulations. To perform robust component analysis, however, is not straightforward and typically requires the tuning of parameters and the preprocessing of data. Moreover the degree of accuracy that can be attained by these methods depends on the configuration of the system, which must be properly taken into account when setting up experimental studies. Here, we review the methods of Kalman filtering, linear and penalised spline regression, and minimal energy expenditure estimation in the context of component analysis and discuss their results on high resolution datasets from mice and rats. In addition, we investigate the effect of the sample time, the accuracy of the activity sensor, and the washout time of the chamber on the estimation accuracy. We found that on the high resolution data there was a strong correlation between the results of Kalman filtering and P-spline regression, except for the activity respiratory quotient. For low resolution data the basal metabolic rate and resting respiratory quotient could still be estimated accurately with P-spline regression, having a strong correlation with the high resolution estimate (R2 > 0.997; sample time of 9 min. In contrast, the thermic effect of food and activity related energy expenditure were more sensitive to a reduction in the sample rate (R2 > 0.97.In conclusion, for component analysis on data generated by single channel systems with continuous data acquisition both Kalman filtering and P-spline regression can be used, while for low resolution data from multichannel systems P-spline regression gives more robust results.

Response of orthotropic micropolar elastic medium due to time ...

Indian Academy of Sciences (India)

R. Narasimhan (Krishtel eMaging) 1461 1996 Oct 15 13:05:22

namic response of anisotropic continuum has received the attention of ... linear theory of micropolar elasticity and bending of orthotropic micropolar ... medium due to time harmonic concentrated load, the continuum is divided into two half-.

Towards best-case response times of real-time tasks under fixed-priority scheduling with deferred preemption

NARCIS (Netherlands)

Bril, R.J.; Verhaegh, W.F.J.; Puaut, I.

2005-01-01

In this paper, we present lower bounds for best-case response times of periodic tasks under fixed-priority scheduling with deferred preemption (FPDS) and arbitrary phasing. Our analysis is based on a dedicated conjecture for a ¿-optimal instant, and uses the notion of best-case occupied time. We

Components of ongoing EEG with high correlation point to emotionally-laden attention -- a possible marker of engagement?

Directory of Open Access Journals (Sweden)

Jacek P Dmochowski

2012-05-01

Full Text Available Recent evidence from functional magnetic resonance imaging suggests that cortical hemodynamic responses coincide in different subjects experiencing a common naturalistic stimulus. Here we utilize neural responses in the electroencephalogram (EEG evoked by multiple presentations of short film clips to index brain states marked by high levels of correlation within and across subjects. We formulate a novel signal decomposition method which extracts maximally correlated signal components from multiple EEG records. The resulting components capture correlations down to a one-second time resolution, thus revealing that peak correlations of neural activity across viewings can occur in remarkable correspondence with arousing moments of the film. Moreover, a significant reduction in neural correlation occurs upon a second viewing of the film or when the narrative is disrupted by presenting its scenes scrambled in time. We also probe oscillatory brain activity during periods of heightened correlation, and observe during such times a significant increase in the theta-band for a frontal component and reductions in the alpha and beta frequency bands for parietal and occipital components. Low-resolution EEG tomography of these components suggests that the correlated neural activity is consistent with sources in the cingulate and orbitofrontal cortices. Put together, these results suggest that the observed synchrony reflects attention- and emotion-modulated cortical processing, and that naturalistic brain states such as engagement may be decoded with high temporal resolution by extracting maximally correlated components of neural activity.

Smart time-pulse coding photoconverters as basic components 2D-array logic devices for advanced neural networks and optical computers

Science.gov (United States)

Krasilenko, Vladimir G.; Nikolsky, Alexander I.; Lazarev, Alexander A.; Michalnichenko, Nikolay N.

2004-04-01

The article deals with a conception of building arithmetic-logic devices (ALD) with a 2D-structure and optical 2D-array inputs-outputs as advanced high-productivity parallel basic operational training modules for realization of basic operation of continuous, neuro-fuzzy, multilevel, threshold and others logics and vector-matrix, vector-tensor procedures in neural networks, that consists in use of time-pulse coding (TPC) architecture and 2D-array smart optoelectronic pulse-width (or pulse-phase) modulators (PWM or PPM) for transformation of input pictures. The input grayscale image is transformed into a group of corresponding short optical pulses or time positions of optical two-level signal swing. We consider optoelectronic implementations of universal (quasi-universal) picture element of two-valued ALD, multi-valued ALD, analog-to-digital converters, multilevel threshold discriminators and we show that 2D-array time-pulse photoconverters are the base elements for these devices. We show simulation results of the time-pulse photoconverters as base components. Considered devices have technical parameters: input optical signals power is 200nW_200μW (if photodiode responsivity is 0.5A/W), conversion time is from tens of microseconds to a millisecond, supply voltage is 1.5_15V, consumption power is from tens of microwatts to a milliwatt, conversion nonlinearity is less than 1%. One cell consists of 2-3 photodiodes and about ten CMOS transistors. This simplicity of the cells allows to carry out their integration in arrays of 32x32, 64x64 elements and more.

The link between response time and preference, variance and processing heterogeneity in stated choice experiments

DEFF Research Database (Denmark)

Campbell, Danny; Mørkbak, Morten Raun; Olsen, Søren Bøye

2018-01-01

In this article we utilize the time respondents require to answer a self-administered online stated preference survey. While the effects of response time have been previously explored, this article proposes a different approach that explicitly recognizes the highly equivocal relationship between ...... between response time and utility coefficients, error variance and processing strategies. Our results thus emphasize the importance of considering response time when modeling stated choice data....... response time and respondents' choices. In particular, we attempt to disentangle preference, variance and processing heterogeneity and explore whether response time helps to explain these three types of heterogeneity. For this, we divide the data (ordered by response time) into approximately equal......-sized subsets, and then derive different class membership probabilities for each subset. We estimate a large number of candidate models and subsequently conduct a frequentist-based model averaging approach using information criteria to derive weights of evidence for each model. Our findings show a clear link...

Time-dependent tritium inventories and flow rates in fuel cycle components of a tokamak fusion reactor

International Nuclear Information System (INIS)

Kuan, W.

1995-01-01

Time-dependent inventories and flow rates for several components of the fuel cycle are modeled and studied through the use of a new modular-type model for the dynamic simulation of the fuel cycle in a fusion reactor. The complex dynamic behavior in the modeled subsystems is analyzed using this new model. Preliminary results using fuel cycle design configurations similar to ITER are presented and analyzed. The inventories and flow rates inside the primary vacuum pumping, fuel cleanup unit and isotope separation system are studied. Ways to minimize the tritium inventory are also assessed. This was performed by looking at various design options that could be used to minimize tritium inventory for specific components. (orig.)

Acute Anxiety Predicts Components of the Cold Shock Response on Cold Water Immersion: Toward an Integrated Psychophysiological Model of Acute Cold Water Survival.

Science.gov (United States)

Barwood, Martin J; Corbett, Jo; Massey, Heather; McMorris, Terry; Tipton, Mike; Wagstaff, Christopher R D

2018-01-01

Introduction: Drowning is a leading cause of accidental death. In cold-water, sudden skin cooling triggers the life-threatening cold shock response (CSR). The CSR comprises tachycardia, peripheral vasoconstriction, hypertension, inspiratory gasp, and hyperventilation with the hyperventilatory component inducing hypocapnia and increasing risk of aspirating water to the lungs. Some CSR components can be reduced by habituation (i.e., reduced response to stimulus of same magnitude) induced by 3-5 short cold-water immersions (CWI). However, high levels of acute anxiety, a plausible emotion on CWI: magnifies the CSR in unhabituated participants, reverses habituated components of the CSR and prevents/delays habituation when high levels of anxiety are experienced concurrent to immersions suggesting anxiety is integral to the CSR. Purpose: To examine the predictive relationship that prior ratings of acute anxiety have with the CSR. Secondly, to examine whether anxiety ratings correlated with components of the CSR during immersion before and after induction of habituation. Methods: Forty-eight unhabituated participants completed one (CON1) 7-min immersion in to cold water (15°C). Of that cohort, twenty-five completed four further CWIs that would ordinarily induce CSR habituation. They then completed two counter-balanced immersions where anxiety levels were increased (CWI-ANX) or were not manipulated (CON2). Acute anxiety and the cardiorespiratory responses (cardiac frequency [ f c ], respiratory frequency [ f R ], tidal volume [ V T ], minute ventilation [ E ]) were measured. Multiple regression was used to identify components of the CSR from the most life-threatening period of immersion (1 st minute) predicted by the anxiety rating prior to immersion. Relationships between anxiety rating and CSR components during immersion were assessed by correlation. Results: Anxiety rating predicted the f c component of the CSR in unhabituated participants (CON1; p CSR when anxiety

Postural threat differentially affects the feedforward and feedback components of the vestibular-evoked balance response.

Science.gov (United States)

Osler, Callum J; Tersteeg, M C A; Reynolds, Raymond F; Loram, Ian D

2013-10-01

Circumstances may render the consequence of falling quite severe, thus maximising the motivation to control postural sway. This commonly occurs when exposed to height and may result from the interaction of many factors, including fear, arousal, sensory information and perception. Here, we examined human vestibular-evoked balance responses during exposure to a highly threatening postural context. Nine subjects stood with eyes closed on a narrow walkway elevated 3.85 m above ground level. This evoked an altered psycho-physiological state, demonstrated by a twofold increase in skin conductance. Balance responses were then evoked by galvanic vestibular stimulation. The sway response, which comprised a whole-body lean in the direction of the edge of the walkway, was significantly and substantially attenuated after ~800 ms. This demonstrates that a strong reason to modify the balance control strategy was created and subjects were highly motivated to minimise sway. Despite this, the initial response remained unchanged. This suggests little effect on the feedforward settings of the nervous system responsible for coupling pure vestibular input to functional motor output. The much stronger, later effect can be attributed to an integration of balance-relevant sensory feedback once the body was in motion. These results demonstrate that the feedforward and feedback components of a vestibular-evoked balance response are differently affected by postural threat. Although a fear of falling has previously been linked with instability and even falling itself, our findings suggest that this relationship is not attributable to changes in the feedforward vestibular control of balance. © 2013 Federation of European Neuroscience Societies and John Wiley & Sons Ltd.

Independent component analysis for cochlear implant artifacts attenuation from electrically evoked auditory steady-state response measurements

Science.gov (United States)

Deprez, Hanne; Gransier, Robin; Hofmann, Michael; van Wieringen, Astrid; Wouters, Jan; Moonen, Marc

2018-02-01

Objective. Electrically evoked auditory steady-state responses (EASSRs) are potentially useful for objective cochlear implant (CI) fitting and follow-up of the auditory maturation in infants and children with a CI. EASSRs are recorded in the electro-encephalogram (EEG) in response to electrical stimulation with continuous pulse trains, and are distorted by significant CI artifacts related to this electrical stimulation. The aim of this study is to evaluate a CI artifacts attenuation method based on independent component analysis (ICA) for three EASSR datasets. Approach. ICA has often been used to remove CI artifacts from the EEG to record transient auditory responses, such as cortical evoked auditory potentials. Independent components (ICs) corresponding to CI artifacts are then often manually identified. In this study, an ICA based CI artifacts attenuation method was developed and evaluated for EASSR measurements with varying CI artifacts and EASSR characteristics. Artifactual ICs were automatically identified based on their spectrum. Main results. For 40 Hz amplitude modulation (AM) stimulation at comfort level, in high SNR recordings, ICA succeeded in removing CI artifacts from all recording channels, without distorting the EASSR. For lower SNR recordings, with 40 Hz AM stimulation at lower levels, or 90 Hz AM stimulation, ICA either distorted the EASSR or could not remove all CI artifacts in most subjects, except for two of the seven subjects tested with low level 40 Hz AM stimulation. Noise levels were reduced after ICA was applied, and up to 29 ICs were rejected, suggesting poor ICA separation quality. Significance. We hypothesize that ICA is capable of separating CI artifacts and EASSR in case the contralateral hemisphere is EASSR dominated. For small EASSRs or large CI artifact amplitudes, ICA separation quality is insufficient to ensure complete CI artifacts attenuation without EASSR distortion.

Sensor response monitoring in pressurized water reactors using time series modeling

International Nuclear Information System (INIS)

Upadhyaya, B.R.; Kerlin, T.W.

1978-01-01

Random data analysis in nuclear power reactors for purposes of process surveillance, pattern recognition and monitoring of temperature, pressure, flow and neutron sensors has gained increasing attention in view of their potential for helping to ensure safe plant operation. In this study, application of autoregressive moving-average (ARMA) time series modeling for monitoring temperature sensor response characteristrics is presented. The ARMA model is used to estimate the step and ramp response of the sensors and the related time constant and ramp delay time. The ARMA parameters are estimated by a two-stage algorithm in the spectral domain. Results of sensor testing for an operating pressurized water reactor are presented. 16 refs

Differentiating emotional responses to images and words

DEFF Research Database (Denmark)

Jensen, Camilla Birgitte Falk; Petersen, Michael Kai; Larsen, Jakob Eg

responses are characterized by only small voltage changes that have typically been found in group studies involving multiple trials and large numbers of participants. Hypothesizing that spatial filtering might enhance retrieval, we apply independent component analysis (ICA) to cluster scalp maps and time...... series responses in a single subject based on only a few trials. Comparing our results against previous findings we identify multiple early and late ICA components that are similarly modulated by neutral, pleasant and unpleasant content in both images and words. Suggesting that we might be able to model...

The Component Timed-Up-and-Go test: the utility and psychometric properties of using a mobile application to determine prosthetic mobility in people with lower limb amputations.

Science.gov (United States)

Clemens, Sheila M; Gailey, Robert S; Bennett, Christopher L; Pasquina, Paul F; Kirk-Sanchez, Neva J; Gaunaurd, Ignacio A

2018-03-01

Using a custom mobile application to evaluate the reliability and validity of the Component Timed-Up-and-Go test to assess prosthetic mobility in people with lower limb amputation. Cross-sectional design. National conference for people with limb loss. A total of 118 people with non-vascular cause of lower limb amputation participated. Subjects had a mean age of 48 (±13.7) years and were an average of 10 years post amputation. Of them, 54% ( n = 64) of subjects were male. None. The Component Timed-Up-and-Go was administered using a mobile iPad application, generating a total time to complete the test and five component times capturing each subtask (sit to stand transitions, linear gait, turning) of the standard timed-up-and-go test. The outcome underwent test-retest reliability using intraclass correlation coefficients (ICCs) and convergent validity analyses through correlation with self-report measures of balance and mobility. The Component Timed-Up-and-Go exhibited excellent test-retest reliability with ICCs ranging from .98 to .86 for total and component times. Evidence of discriminative validity resulted from significant differences in mean total times between people with transtibial (10.1 (SD: ±2.3)) and transfemoral (12.76 (SD: ±5.1) amputation, as well as significant differences in all five component times ( P < .05). Convergent validity of the Component Timed-Up-and-Go was demonstrated through moderate correlations with the PLUS-M ( r s  = -.56). The Component Timed-Up-and-Go is a reliable and valid clinical tool for detailed assessment of prosthetic mobility in people with non-vascular lower limb amputation. The iPad application provided a means to easily record data, contributing to clinical utility.

Principal response curves: analysis of time-dependent multivariate responses of biological community to stress

NARCIS (Netherlands)

Brink, van den P.J.; Braak, ter C.J.F.

1999-01-01

In this paper a novel multivariate method is proposed for the analysis of community response data from designed experiments repeatedly sampled in time. The long-term effects of the insecticide chlorpyrifos on the invertebrate community and the dissolved oxygen (DO)–pH–alkalinity–conductivity

Time response characteristics of X-ray detector system on Silex-Ⅰ laser facility

International Nuclear Information System (INIS)

Yi Rongqing; He Xiao'an; Li Hang; Du Huabing; Zhang Haiying; Cao Zhurong

2013-01-01

On the Silex-Ⅰ laser facility, the time response characteristics of XRD detector were studied. A laser with a pulse of 32 fs and a wavelength of 800 nm was used to irradiate a plane Au target. X-ray calibrated method of time of exposure X-ray framing camera and time resolution of X-ray streak camera was explored. The time response characteristics of XRD detector and time process of X-ray emission were obtained from experiment. We obtained X-ray calibration method of time of exposure X-ray framing camera and time resolution of X-ray streak camera. (authors)

Investigation of relative arrival time distributions of EAS electron and muon component with the KASCADE central detector

International Nuclear Information System (INIS)

Hafemann, W.; Haeusler, R.; Rebel, H.; Mathes, H.J.

2000-01-01

The central detector of the KASCADE experiment is equipped with two layers of scintillation detectors with different area coverage. The scintillators of both detector systems have a good timing resolution of about 1.6 ns. With these two arrangements we performed extensive measurements of the arrival time differences at different energy thresholds of the electron and the muon component of EAS. The observed time structure of the shower profile is classified according to different EAS parameters. We furthermore present an analysis and comparism based on detailed MC simulations of the shower development. This comparism shows good agreement between experimental data and the expected behaviour of the different time distributions. (orig.)

Motor preparation is modulated by the resolution of the response timing information.

Science.gov (United States)

Carlsen, Anthony N; Mackinnon, Colum D

2010-03-31

In the present experiment, the temporal predictability of response time was systematically manipulated to examine its effect on the time course of motor pre-programming and release of the intended movement by an acoustic startle stimulus. Participants performed a ballistic right wrist extension task in four different temporal conditions: 1) a variable foreperiod simple RT task, 2) a fixed foreperiod simple RT task, 3) a low resolution countdown anticipation-timing task, and 4) a high resolution anticipation-timing task. For each task, a startling acoustic stimulus (124dB) was presented at several intervals prior to the "go" signal ("go" -150ms, -500ms, and -1500ms). Results from the startle trials showed that the time course of movement pre-programming was affected by the temporal uncertainty of the imperative "go" cue. These findings demonstrate that the resolution of the timing information regarding the response cue has a marked effect on the timing of movement preparation such that under conditions of low temporal resolution, participants plan the movement well in advance in accordance with the anticipated probability of onset of the cue, whereas movement preparation is delayed until less than 500ms prior to response time when continuous temporal information is provided. Copyright 2010 Elsevier B.V. All rights reserved.

Component effects in mixture experiments

International Nuclear Information System (INIS)

Piepel, G.F.

1980-01-01

In a mixture experiment, the response to a mixture of q components is a function of the proportions x 1 , x 2 , ..., x/sub q/ of components in the mixture. Experimental regions for mixture experiments are often defined by constraints on the proportions of the components forming the mixture. The usual (orthogonal direction) definition of a factor effect does not apply because of the dependence imposed by the mixture restriction, /sup q/Σ/sub i=1/ x/sub i/ = 1. A direction within the experimental region in which to compute a mixture component effect is presented and compared to previously suggested directions. This new direction has none of the inadequacies or errors of previous suggestions while having a more meaningful interpretation. The distinction between partial and total effects is made. The uses of partial and total effects (computed using the new direction) in modification and interpretation of mixture response prediction equations are considered. The suggestions of the paper are illustrated in an example from a glass development study in a waste vitrification program. 5 figures, 3 tables

Relative planting times on the production components in sesame/cowpea bean intercropping in organic system

Directory of Open Access Journals (Sweden)

Afrânio César de Araújo

2013-12-01

Full Text Available Aiming at better land use, small farmers usually plant sesame and cowpea bean intercropped with other crops. The aim of this work was to analyze and quantify the influence of four relative planting times of the cowpea bean in intercropping with sesame from the standpoint of their production components, plant productivity and the index of land equivalent ratio (LER. The field experiment was conducted in a randomized blocks with four treatments and four replicates. The treatments were the sesame and the cowpea bean in intercropping with the cowpea bean planted at the same time, 7, 14 and 21days after than the sesame. A greater part of the production components of both the sesame as well the cowpea bean was affected by the intercropping and significant differences were noted among the treatments in a larger part of the parameters. As the planting of the cowpea bean became more distant from that of the sesame, the yield of the Pedaliaceae increased and the yield of the Fabaceae decreased. The results for LER findings on the other hand suggest that in the sesame/cowpea bean intercropping, when the Fabaceae is planted seven days after the sesame, there is better use of the land and a largest possibility to the producer earning a profit.

Time response prediction of Brazilian Nuclear Power Plant temperature sensors using neural networks

Energy Technology Data Exchange (ETDEWEB)

Santos, Roberto Carlos dos; Pereira, Iraci Martinez, E-mail: rcsantos@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2011-07-01

This work presents the results of the time constants values predicted from ANN using Angra I Brazilian nuclear power plant data. The signals obtained from LCSR loop current step response test sensors installed in the process presents noise end fluctuations that are inherent of operational conditions. Angra I nuclear power plant has 20 RTDs as part of the protection reactor system. The results were compared with those obtained from traditional way. Primary coolant RTDs (Resistance Temperature Detector) typically feed the plant's control and safety systems and must, therefore, be very accurate and have good dynamic performance. An in-situ test method called LCSR - loop current step response test was developed to measure remotely the response time of RTDs. In the LCSR method, the response time of the sensor is identified by means of the LCSR transformation that involves the dynamic response modal time constants determination using a nodal heat transfer model. For this reason, this calculation is not simple and requires specialized personnel. This work combines the two methodologies, Plunge test and LCSR test, using neural networks. With the use of neural networks it will not be necessary to use the LCSR transformation to determine sensor's time constant and this leads to more robust results. (author)

Time response prediction of Brazilian Nuclear Power Plant temperature sensors using neural networks

International Nuclear Information System (INIS)

Santos, Roberto Carlos dos; Pereira, Iraci Martinez

2011-01-01

This work presents the results of the time constants values predicted from ANN using Angra I Brazilian nuclear power plant data. The signals obtained from LCSR loop current step response test sensors installed in the process presents noise end fluctuations that are inherent of operational conditions. Angra I nuclear power plant has 20 RTDs as part of the protection reactor system. The results were compared with those obtained from traditional way. Primary coolant RTDs (Resistance Temperature Detector) typically feed the plant's control and safety systems and must, therefore, be very accurate and have good dynamic performance. An in-situ test method called LCSR - loop current step response test was developed to measure remotely the response time of RTDs. In the LCSR method, the response time of the sensor is identified by means of the LCSR transformation that involves the dynamic response modal time constants determination using a nodal heat transfer model. For this reason, this calculation is not simple and requires specialized personnel. This work combines the two methodologies, Plunge test and LCSR test, using neural networks. With the use of neural networks it will not be necessary to use the LCSR transformation to determine sensor's time constant and this leads to more robust results. (author)

Time domain simulation of the response of geometrically nonlinear panels subjected to random loading

Science.gov (United States)

Moyer, E. Thomas, Jr.

1988-01-01

The response of composite panels subjected to random pressure loads large enough to cause geometrically nonlinear responses is studied. A time domain simulation is employed to solve the equations of motion. An adaptive time stepping algorithm is employed to minimize intermittent transients. A modified algorithm for the prediction of response spectral density is presented which predicts smooth spectral peaks for discrete time histories. Results are presented for a number of input pressure levels and damping coefficients. Response distributions are calculated and compared with the analytical solution of the Fokker-Planck equations. RMS response is reported as a function of input pressure level and damping coefficient. Spectral densities are calculated for a number of examples.

Response-only modal identification using random decrement algorithm with time-varying threshold level

International Nuclear Information System (INIS)

Lin, Chang Sheng; Tseng, Tse Chuan

2014-01-01

Modal Identification from response data only is studied for structural systems under nonstationary ambient vibration. The topic of this paper is the estimation of modal parameters from nonstationary ambient vibration data by applying the random decrement algorithm with time-varying threshold level. In the conventional random decrement algorithm, the threshold level for evaluating random dec signatures is defined as the standard deviation value of response data of the reference channel. The distortion of random dec signatures may be, however, induced by the error involved in noise from the original response data in practice. To improve the accuracy of identification, a modification of the sampling procedure in random decrement algorithm is proposed for modal-parameter identification from the nonstationary ambient response data. The time-varying threshold level is presented for the acquisition of available sample time history to perform averaging analysis, and defined as the temporal root-mean-square function of structural response, which can appropriately describe a wide variety of nonstationary behaviors in reality, such as the time-varying amplitude (variance) of a nonstationary process in a seismic record. Numerical simulations confirm the validity and robustness of the proposed modal-identification method from nonstationary ambient response data under noisy conditions.

Time-variable gravity potential components for optical clock comparisons and the definition of international time scales

International Nuclear Information System (INIS)

Voigt, C.; Denker, H.; Timmen, L.

2016-01-01

The latest generation of optical atomic clocks is approaching the level of one part in 10 18 in terms of frequency stability and uncertainty. For clock comparisons and the definition of international time scales, a relativistic redshift effect of the clock frequencies has to be taken into account at a corresponding uncertainty level of about 0.1 m 2 s -2 and 0.01 m in terms of gravity potential and height, respectively. Besides the predominant static part of the gravity potential, temporal variations must be considered in order to avoid systematic frequency shifts. Time-variable gravity potential components induced by tides and non-tidal mass redistributions are investigated with regard to the level of one part in 10 18 . The magnitudes and dominant time periods of the individual gravity potential contributions are investigated globally and for specific laboratory sites together with the related uncertainty estimates. The basics of the computation methods are presented along with the applied models, data sets and software. Solid Earth tides contribute by far the most dominant signal with a global maximum amplitude of 4.2 m 2 s -2 for the potential and a range (maximum-to-minimum) of up to 1.3 and 10.0 m 2 s -2 in terms of potential differences between specific laboratories over continental and intercontinental scales, respectively. Amplitudes of the ocean tidal loading potential can amount up to 1.25 m 2 s -2 , while the range of the potential between specific laboratories is 0.3 and 1.1 m 2 s -2 over continental and intercontinental scales, respectively. These are the only two contributors being relevant at a 10 -17 level. However, several other time-variable potential effects can particularly affect clock comparisons at the 10 -18 level. Besides solid Earth pole tides, these are non-tidal mass redistributions in the atmosphere, the oceans and the continental water storage. (authors)

Interactions among spectral components of radiation in the growth responses of rice, tomato and strawberry

International Nuclear Information System (INIS)

Inada, K.; Matsuno, A.

1985-01-01

Effects of spectral components and their ratios of radiation on simultaneous growth responses were investigated with rice, tomato and strawberry plants exposed to lights with a high fluence rate (350 or 408 μmol m -2 s -1 , 400-700 nm) during every daytime. Both elongation growth and Ieaf area development in rice and strawberry were promoted by red (R) but inhibited by blue (B) component depending on the each fluence rate. However, leaf area in tomato responded in opposite direction to these. The elongation growth was remarkably increased with the fluence rate of far-red (FR) in tomato and strawberry, but not in rice. These responses were lineary increased, except FR and UV effects, with logarithmic R/B ratio in rice and strawberry but not in tomato. A very low R/FR ratio caused a strong promotion of both elongation and leaf area in tomato, while it promoted petiole elengation but inhibited leaf area development in strawberry. The elongation and leaf area development responded to R/FR in reverse way between rice and strawberry. Chlorophyll content of leaves was generally decreased with the increase of logarithmic R/B ratio in all the species. Areal weight of leaf and dry weight increment/leaf area were more or less increased with R/B and R/ FR ratios, Dry weight increment varied with the spectral ratios in almost the same way as leaf area, suggesting that spectral dependence of photosynthetic production was not much different between the species. Some discussions were made on the photoreceptor pigments involved in the elongation growth and leaf area development, and on the selection of light quantity to ensure a normal growth of each plant species

Transducer frequency response variations investigated by time reversal calibration

Czech Academy of Sciences Publication Activity Database

Kober, Jan; Převorovský, Zdeněk

2016-01-01

Roč. 26, č. 2 (2016), A16-A16 ISSN 1213-3825. [Europen Conference on Acoustic Emission Testing /32./. 07.09.2016-09.09.2016, Praha] Institutional support: RVO:61388998 Keywords : calibration * time reversal * transducer * frequency response Subject RIV: BI - Acoustics

Modeling L2,3-Edge X-ray Absorption Spectroscopy with Real-Time Exact Two-Component Relativistic Time-Dependent Density Functional Theory.

Science.gov (United States)

Kasper, Joseph M; Lestrange, Patrick J; Stetina, Torin F; Li, Xiaosong

2018-04-10

X-ray absorption spectroscopy is a powerful technique to probe local electronic and nuclear structure. There has been extensive theoretical work modeling K-edge spectra from first principles. However, modeling L-edge spectra directly with density functional theory poses a unique challenge requiring further study. Spin-orbit coupling must be included in the model, and a noncollinear density functional theory is required. Using the real-time exact two-component method, we are able to variationally include one-electron spin-orbit coupling terms when calculating the absorption spectrum. The abilities of different basis sets and density functionals to model spectra for both closed- and open-shell systems are investigated using SiCl 4 and three transition metal complexes, TiCl 4 , CrO 2 Cl 2 , and [FeCl 6 ] 3- . Although we are working in the real-time framework, individual molecular orbital transitions can still be recovered by projecting the density onto the ground state molecular orbital space and separating contributions to the time evolving dipole moment.

Modeling Climate Responses to Spectral Solar Forcing on Centennial and Decadal Time Scales

Science.gov (United States)

Wen, G.; Cahalan, R.; Rind, D.; Jonas, J.; Pilewskie, P.; Harder, J.

2012-01-01

We report a series of experiments to explore clima responses to two types of solar spectral forcing on decadal and centennial time scales - one based on prior reconstructions, and another implied by recent observations from the SORCE (Solar Radiation and Climate Experiment) SIM (Spectral 1rradiance Monitor). We apply these forcings to the Goddard Institute for Space Studies (GISS) Global/Middle Atmosphere Model (GCMAM). that couples atmosphere with ocean, and has a model top near the mesopause, allowing us to examine the full response to the two solar forcing scenarios. We show different climate responses to the two solar forCing scenarios on decadal time scales and also trends on centennial time scales. Differences between solar maximum and solar minimum conditions are highlighted, including impacts of the time lagged reSponse of the lower atmosphere and ocean. This contrasts with studies that assume separate equilibrium conditions at solar maximum and minimum. We discuss model feedback mechanisms involved in the solar forced climate variations.

The correlation of fast OSL component with the TL peak at 3250C in quartz of various origins

International Nuclear Information System (INIS)

Kitis, G.; Kiyak, N.; Polymeris, G.S.; Tsirliganis, N.C.

2010-01-01

The fast component of the optically stimulated luminescence (OSL) signal in quartz is the basic tool for the optical dating. Its relation with the thermoluminescence (TL) glow-peak at about 325 deg. C is well established for naturally irradiated quartz. This relationship is also an important part of a general model for quartz on which many theoretical simulations of various OSL experimental results have been based. In the present work this relationship is systematically investigated in nine quartz samples of different origin. The linearly modulated OSL (LM-OSL) curves of all quartz samples for stimulation time less than 50 s consists of two components discriminated easily by a computerized curve deconvolution (CCD) analysis. By comparing the un-bleached to the respective bleached TL glow-curve, it is found that the system of these two fast OSL components is directly related with only a small portion of the electron traps responsible for the TL glow-peaks in the temperature region 200-400 0 C. By increasing the stimulation times, besides the two fast components, the medium and the slow components are also obtained. The medium and slow components are clearly related with the main body of the electron traps responsible for TL glow-peaks in the same temperature region 200-400 0 C. Despite their different origin all quartz samples show an appreciable homogeneity concerning the number and time position of the individual components, whereas, the relative TL/OSL intensities vary strongly from sample to sample with the integrated TL intensity being generally much less than the integrated OSL intensity.

Detecting geothermal anomalies and evaluating LST geothermal component by combining thermal remote sensing time series and land surface model data

NARCIS (Netherlands)

Romaguera, M.; Vaughan, R. G.; Ettema, J.; Izquierdo-Verdiguier, E.; Hecker, C. A.; van der Meer, F. D.

This paper explores for the first time the possibilities to use two land surface temperature (LST) time series of different origins (geostationary Meteosat Second Generation satellite data and Noah land surface modelling, LSM), to detect geothermal anomalies and extract the geothermal component of

Detecting geothermal anomalies and evaluating LST geothermal component by combining thermal remote sensing time series and land surface model data

NARCIS (Netherlands)

Romaguera, M.; Vaughan, R. G.; Ettema, J.; Izquierdo-Verdiguier, E.; Hecker, C. A.; van der Meer, F. D.

2017-01-01

This paper explores for the first time the possibilities to use two land surface temperature (LST) time series of different origins (geostationary Meteosat Second Generation satellite data and Noah land surface modelling, LSM), to detect geothermal anomalies and extract the geothermal component of

Time delays between core power production and external detector response from Monte Carlo calculations

International Nuclear Information System (INIS)

Valentine, T.E.; Mihalczo, J.T.

1996-01-01

One primary concern for design of safety systems for reactors is the time response of external detectors to changes in the core. This paper describes a way to estimate the time delay between the core power production and the external detector response using Monte Carlo calculations and suggests a technique to measure the time delay. The Monte Carlo code KENO-NR was used to determine the time delay between the core power production and the external detector response for a conceptual design of the Advanced Neutron Source (ANS) reactor. The Monte Carlo estimated time delay was determined to be about 10 ms for this conceptual design of the ANS reactor

Femtosecond response time measurements of a Cs2Te photocathode

Science.gov (United States)

Aryshev, A.; Shevelev, M.; Honda, Y.; Terunuma, N.; Urakawa, J.

2017-07-01

Success in design and construction of a compact, high-brightness accelerator system is strongly related to the production of ultra-short electron beams. Recently, the approach to generate short electron bunches or pre-bunched beams in RF guns directly illuminating a high quantum efficiency semiconductor photocathode with femtosecond laser pulses has become attractive. The measurements of the photocathode response time in this case are essential. With an approach of the interferometer-type pulse splitter deep integration into a commercial Ti:Sa laser system used for RF guns, it has become possible to generate pre-bunched electron beams and obtain continuously variable electron bunch separation. In combination with a well-known zero-phasing technique, it allows us to estimate the response time of the most commonly used Cs2Te photocathode. It was demonstrated that the peak-to-peak rms time response of Cs2Te is of the order of 370 fs, and thereby, it is possible to generate and control a THz sequence of relativistic electron bunches by a conventional S-band RF gun. This result can also be applied for investigation of other cathode materials and electron beam temporal shaping and further opens a possibility to construct wide-range tunable, table-top THz free electron laser.

Determination of response time of resistance thermometers by in situ measurements

International Nuclear Information System (INIS)

Goncalves, I.M.P.; Soares, A.J.

1986-01-01

The loop-current-step-response test provides a mean for determining the time constant of resistance thermometers. The test consists in heating the sensor a few degrees above ambient temperature by causing a step perurbation in the electric current that flows through the sensor leads. The developed mathematical transformation permits to use data collected during the internal heating transient to predict the sensor response to perturbations in fluid temperature. Experimental data obtained show that time constant determined by this method is within 15 percent of the true value. (Author) [pt

Design and Manufacturing of Young 3 and 4 NSSS Components

International Nuclear Information System (INIS)

Chung, Chungwoon

1989-01-01

Korea nuclear unit 11 and 12 (Young 3 and 4) project, which is the 6th nuclear construction project in Korea, has been implemented since 1987. The project is scheduled to commence commercial operation by March 1995 and March 1996, respectively. The project is executed in such a manner that local firms play the leading role. In parallel with the project, nationwide technical self-reliance program for nuclear power plant construction is activated. Accordingly, the clear-cut division and achievement of responsibilities assigned to local firms will determine the success of this project and future nuclear projects. The local manufacturer takes responsibility for on-time delivery of safety-assured and reliable equipment and also for achieving technical self-reliance in component design and manufacturing. This paper describes the objectives to be achieved by the local manufacturer in the execution of design and manufacturing of NSSS components for the project and action plans taken and/or to be taken to achieve those objectives

Improved response time of flexible microelectromechanical sensors employing eco-friendly nanomaterials.

Science.gov (United States)

Fan, Shicheng; Dan, Li; Meng, Lingju; Zheng, Wei; Elias, Anastasia; Wang, Xihua

2017-11-09

Flexible force/pressure sensors are of interest for academia and industry and have applications in wearable technologies. Most of such sensors on the market or reported in journal publications are based on the operation mechanism of probing capacitance or resistance changes of the materials under pressure. Recently, we reported the microelectromechanical (MEM) sensors based on a different mechanism: mechanical switches. Multiples of such MEM sensors can be integrated to achieve the same function of regular force/pressure sensors while having the advantages of ease of fabrication and long-term stability in operation. Herein, we report the dramatically improved response time (more than one order of magnitude) of these MEM sensors by employing eco-friendly nanomaterials-cellulose nanocrystals. For instance, the incorporation of polydimethysiloxane filled with cellulose nanocrystals shortened the response time of MEM sensors from sub-seconds to several milliseconds, leading to the detection of both diastolic and systolic pressures in the radial arterial blood pressure measurement. Comprehensive mechanical and electrical characterization of the materials and the devices reveal that greatly enhanced storage modulus and loss modulus play key roles in this improved response time. The demonstrated fast-response flexible sensors enabled continuous monitoring of heart rate and complex cardiovascular signals using pressure sensors for future wearable sensing platforms.

Performance on a simple response time task: Is sleep or work more important for miners?

Science.gov (United States)

Ferguson, Sally A; Paech, Gemma M; Dorrian, Jillian; Roach, Gregory D; Jay, Sarah M

2011-01-01

The purpose of the current study was to investigate the impact of work- and sleep-related factors on an objective measure of response time in a field setting. Thirty-five mining operators working 12-h shift patterns completed daily sleep and work diaries, wore activity monitors continuously and completed palm-based psychomotor vigilance tests (palmPVT) at the start and end of each shift. Linear mixed models were used to test the main effects on response time of roster, timing of test, sleep history and prior wake. The time at which the test occurred was a significant predictor of response time (F₃(,)₄₀₃(.)₄ = 6.72, p times than the start of night shifts, and the start or end of day shifts. Further, the amount of sleep obtained in the 24h prior to the test was also a significant predictor of response time (F₃(,)₄₀₇(.)₀ = 3.05, p time indicative of performance impairments. Of more interest however is that immediate sleep history was also predictive of changes in response time with lower amounts of prior sleep related to slower response times. The current data provides further evidence that sleep is a primary mediator of performance, independent of roster pattern. Copyright © 2010 Elsevier Ltd and The Ergonomics Society. All rights reserved.

Larger Neural Responses Produce BOLD Signals That Begin Earlier in Time

Directory of Open Access Journals (Sweden)

Serena eThompson

2014-06-01

Full Text Available Functional MRI analyses commonly rely on the assumption that the temporal dynamics of hemodynamic response functions (HRFs are independent of the amplitude of the neural signals that give rise to them. The validity of this assumption is particularly important for techniques that use fMRI to resolve sub-second timing distinctions between responses, in order to make inferences about the ordering of neural processes. Whether or not the detailed shape of the HRF is independent of neural response amplitude remains an open question, however. We performed experiments in which we measured responses in primary visual cortex (V1 to large, contrast-reversing checkerboards at a range of contrast levels, which should produce varying amounts of neural activity. Ten subjects (ages 22-52 were studied in each of two experiments using 3 Tesla scanners. We used rapid, 250 msec, temporal sampling (repetition time, or TR and both short and long inter-stimulus interval (ISI stimulus presentations. We tested for a systematic relationship between the onset of the HRF and its amplitude across conditions, and found a strong negative correlation between the two measures when stimuli were separated in time (long- and medium-ISI experiments, but not the short-ISI experiment. Thus, stimuli that produce larger neural responses, as indexed by HRF amplitude, also produced HRFs with shorter onsets. The relationship between amplitude and latency was strongest in voxels with lowest mean-normalized variance (i.e., parenchymal voxels. The onset differences observed in the longer-ISI experiments are likely attributable to mechanisms of neurovascular coupling, since they are substantially larger than reported differences in the onset of action potentials in V1 as a function of response amplitude.

Predicting response times for the Spotify backend

OpenAIRE

Yanggratoke, Rerngvit; Kreitz, Gunnar; Goldmann, Mikael; Stadler, Rolf

2012-01-01

We model and evaluate the performance of a distributed key-value storage system that is part of the Spotify backend. Spotify is an on-demand music streaming service, offering low-latency access to a library of over 16 million tracks and serving over 10 million users currently. We first present a simplified model of the Spotify storage architecture, in order to make its analysis feasible. We then introduce an analytical model for the distribution of the response time, a key metric in the Spoti...

Sustained visual-spatial attention produces costs and benefits in response time and evoked neural activity.

Science.gov (United States)

Mangun, G R; Buck, L A

1998-03-01

This study investigated the simple reaction time (RT) and event-related potential (ERP) correlates of biasing attention towards a location in the visual field. RTs and ERPs were recorded to stimuli flashed randomly and with equal probability to the left and right visual hemifields in the three blocked, covert attention conditions: (i) attention divided equally to left and right hemifield locations; (ii) attention biased towards the left location; or (iii) attention biased towards the right location. Attention was biased towards left or right by instructions to the subjects, and responses were required to all stimuli. Relative to the divided attention condition, RTs were significantly faster for targets occurring where more attention was allocated (benefits), and slower to targets where less attention was allocated (costs). The early P1 (100-140 msec) component over the lateral occipital scalp regions showed attentional benefits. There were no amplitude modulations of the occipital N1 (125-180 msec) component with attention. Between 200 and 500 msec latency, a late positive deflection (LPD) showed both attentional costs and benefits. The behavioral findings show that when sufficiently induced to bias attention, human observers demonstrate RT benefits as well as costs. The corresponding P1 benefits suggest that the RT benefits of spatial attention may arise as the result of modulations of visual information processing in the extrastriate visual cortex.

Stroop interference and the timing of selective response activation.

NARCIS (Netherlands)

Lansbergen, M.M.; Kenemans, J.L.

2008-01-01

OBJECTIVE: To examine the exact timing of selective response activation in a manual color-word Stroop task. METHODS: Healthy individuals performed two versions of a manual color-word Stroop task, varying in the probability of incongruent color-words, while EEG was recorded. RESULTS: Stroop

Time to Response to Citalopram Treatment for Agitation in Alzheimer Disease.

Science.gov (United States)

Weintraub, Daniel; Drye, Lea T; Porsteinsson, Anton P; Rosenberg, Paul B; Pollock, Bruce G; Devanand, Devangere P; Frangakis, Constantine; Ismail, Zahinoor; Marano, Christopher; Meinert, Curtis L; Mintzer, Jacobo E; Munro, Cynthia A; Pelton, Gregory; Rabins, Peter V; Schneider, Lon S; Shade, David M; Yesavage, Jerome; Lyketsos, Constantine G

2015-11-01

Agitation is a common and significant problem in Alzheimer disease (AD). In the recent Citalopram for Agitation in Alzheimer's Disease (CitAD) study, citalopram was efficacious for the treatment of AD agitation. Here we examined the time course and predictors of response to treatment. Response in CitAD was defined as a modified Alzheimer Disease Cooperative Study Clinical Global Impression of Change (CGIC) score of 1 or 2 or a Neurobehavioral Rating Scale agitation subscale (NBRS-A) score reduction ≥ 50% from baseline. "Stable early response" was defined as meeting the aforementioned criteria at both weeks 3 and 9, "late response" was response at week 9 but not at week 3, and "unstable response" was response at week 3 but not at week 9. In the primary analyses, citalopram was superior to placebo on both the CGIC and the NBRS-A response measures. Little between-group differences were found in response rates in the first 3 weeks of the study (21% versus 19% on the CGIC). Citalopram patients were more likely than placebo patients to be a late responder (18% versus 8% on CGIC, Fisher's exact p = 0.09; 31% versus 15% on NBRS-A, Fisher's exact p = 0.02). Approximately half of citalopram responders (45%-56%) at end of study achieved response later in the study compared with 30%-44% of placebo responders. Treatment with citalopram for agitation in AD needs to be at least 9 weeks in duration to allow sufficient time for full response. Study duration is an important factor to consider in the design of clinical trials for agitation in AD. Copyright © 2015 American Association for Geriatric Psychiatry. Published by Elsevier Inc. All rights reserved.

Increased reaction time variability in attention-deficit hyperactivity disorder as a response-related phenomenon: evidence from single-trial event-related potentials.

Science.gov (United States)

Saville, Christopher W N; Feige, Bernd; Kluckert, Christian; Bender, Stephan; Biscaldi, Monica; Berger, Andrea; Fleischhaker, Christian; Henighausen, Klaus; Klein, Christoph

2015-07-01

Increased intra-subject variability (ISV) in reaction times (RTs) is a promising endophenotype for attention-deficit hyperactivity disorder (ADHD) and among the most robust hallmarks of the disorder. ISV has been assumed to represent an attentional deficit, either reflecting lapses in attention or increased neural noise. Here, we use an innovative single-trial event-related potential approach to assess whether the increased ISV associated with ADHD is indeed attributable to attention, or whether it is related to response-related processing. We measured electroencephalographic responses to working memory oddball tasks in patients with ADHD (N = 20, aged 11.3 ± 1.1) and healthy controls (N = 25, aged 11.7 ± 1.1), and analysed these data with a recently developed method of single-trial event-related potential analysis. Estimates of component latency variability were computed for the stimulus-locked and response-locked forms of the P3b and the lateralised readiness potential (LRP). ADHD patients showed significantly increased ISV in behavioural ISV. This increased ISV was paralleled by an increase in variability in response-locked event-related potential latencies, while variability in stimulus-locked latencies was equivalent between groups. This result held across the P3b and LRP. Latency of all components predicted RTs on a single-trial basis, confirming that all were relevant for speed of processing. These data suggest that the increased ISV found in ADHD could be associated with response-end, rather than stimulus-end processes, in contrast to prevailing conceptions about the endophenotype. This mental chronometric approach may also be useful for exploring whether the existing lack of specificity of ISV to particular psychiatric conditions can be improved upon. © 2014 Association for Child and Adolescent Mental Health.

Oscillatory frontal theta responses are increased upon bisensory stimulation.

Science.gov (United States)

Sakowitz, O W; Schürmann, M; Başar, E

2000-05-01

To investigate the functional correlation of oscillatory EEG components with the interaction of sensory modalities following simultaneous audio-visual stimulation. In an experimental study (15 subjects) we compared auditory evoked potentials (AEPs) and visual evoked potentials (VEPs) to bimodal evoked potentials (BEPs; simultaneous auditory and visual stimulation). BEPs were assumed to be brain responses to complex stimuli as a marker for intermodal associative functioning. Frequency domain analysis of these EPs showed marked theta-range components in response to bimodal stimulation. These theta components could not be explained by linear addition of the unimodal responses in the time domain. Considering topography the increased theta-response showed a remarkable frontality in proximity to multimodal association cortices. Referring to methodology we try to demonstrate that, even if various behavioral correlates of brain oscillations exist, common patterns can be extracted by means of a systems-theoretical approach. Serving as an example of functionally relevant brain oscillations, theta responses could be interpreted as an indicator of associative information processing.

Replaceable LMFBR core components

International Nuclear Information System (INIS)

Evans, E.A.; Cunningham, G.W.

1976-01-01

Much progress has been made in understanding material and component performance in the high temperature, fast neutron environment of the LMFBR. Current data have provided strong assurance that the initial core component lifetime objectives of FFTF and CRBR can be met. At the same time, this knowledge translates directly into the need for improved core designs that utilize improved materials and advanced fuels required to meet objectives of low doubling times and extended core component lifetimes. An industrial base for the manufacture of quality core components has been developed in the US, and all procurements for the first two core equivalents for FFTF will be completed this year. However, the problem of fabricating recycled plutonium while dramatically reducing fabrication costs, minimizing personnel exposure, and protecting public health and safety must be addressed

Dynamics stresses in pipelines and components

International Nuclear Information System (INIS)

Prates, C.L.M.; Stukart, R.N.L.; Halbritter, A.L.

1982-01-01

The procedure to generate the dynamic stresses caused by external events, necessary for the structural calculation of pipelines and components in nuclear power plants is presented. A special attention is given to the stress caused by the action of earthquakes and exterior explosions. In the dynamic analysis of pipeline and components is usually to show the stresses procedured by these events under the response spectra form. The methodology to obtain these response spectra is shown and discussed. Some pratical examples of spectra from nuclear power plant building are still shown. (E.G.) [pt

Dose-response association between leisure time physical activity and work ability

DEFF Research Database (Denmark)

Calatayud, Joaquin; Jakobsen, Markus D.; Sundstrup, Emil

2015-01-01

INTRODUCTION: Regular physical activity is important for longevity and health, but knowledge about the optimal dose of physical activity for maintaining good work ability is unknown. This study investigates the association between intensity and duration of physical activity during leisure time......, lifestyle and chronic disease showed that the duration of high-intensity physical activity during leisure was positively associated with work ability, in a dose-response fashion (p physical activity per week had on average 8 points higher work ability...... than those not performing such activities. The duration of low-intensity leisure-time physical activity was not associated with work ability (p = 0.5668). CONCLUSIONS: The duration of high-intensity physical activity during leisure time is associated in a dose-response fashion with work ability...

A plan for safety and integrity of research reactor components

International Nuclear Information System (INIS)

Moatty, Mona S. Abdel; Khattab, M.S.

2013-01-01

Highlights: ► A plan for in-service inspection of research reactor components is put. ► Section XI of the ASME Code requirements is applied. ► Components subjected to inspection and their classes are defined. ► Flaw evaluation and its acceptance–rejection criteria are reviewed. ► A plan of repair or replacement is prepared. -- Abstract: Safety and integrity of a research reactor that has been operated over 40 years requires frequent and thorough inspection of all the safety-related components of the facility. The need of increasing the safety is the need of improving the reliability of its systems. Diligent and extensive planning of in-service inspection (ISI) of all reactor components has been imposed for satisfying the most stringent safety requirements. The Safeguards Officer's responsibilities of Section XI of the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code ASME Code have been applied. These represent the most extensive and time-consuming part of ISI program, and identify the components subjected to inspection and testing, methods of component classification, inspection and testing techniques, acceptance/rejection criteria, and the responsibilities. The paper focuses on ISI planning requirements for welded systems such as vessels, piping, valve bodies, pump casings, and control rod-housing parts. The weld in integral attachments for piping, pumps, and valves are considered too. These are taken in consideration of safety class (1, 2, 3, etc.), reactor age, and weld type. The parts involve in the frequency of inspection, the examination requirements for each inspection, the examination method are included. Moreover the flaw evaluation, the plan of repair or replacement, and the qualification of nondestructive examination personnel are considered

Workload Capacity: A Response Time-Based Measure of Automation Dependence.

Science.gov (United States)

Yamani, Yusuke; McCarley, Jason S

2016-05-01

An experiment used the workload capacity measure C(t) to quantify the processing efficiency of human-automation teams and identify operators' automation usage strategies in a speeded decision task. Although response accuracy rates and related measures are often used to measure the influence of an automated decision aid on human performance, aids can also influence response speed. Mean response times (RTs), however, conflate the influence of the human operator and the automated aid on team performance and may mask changes in the operator's performance strategy under aided conditions. The present study used a measure of parallel processing efficiency, or workload capacity, derived from empirical RT distributions as a novel gauge of human-automation performance and automation dependence in a speeded task. Participants performed a speeded probabilistic decision task with and without the assistance of an automated aid. RT distributions were used to calculate two variants of a workload capacity measure, COR(t) and CAND(t). Capacity measures gave evidence that a diagnosis from the automated aid speeded human participants' responses, and that participants did not moderate their own decision times in anticipation of diagnoses from the aid. Workload capacity provides a sensitive and informative measure of human-automation performance and operators' automation dependence in speeded tasks. © 2016, Human Factors and Ergonomics Society.

Principal component analysis of MSBAS DInSAR time series from Campi Flegrei, Italy

Science.gov (United States)

Tiampo, Kristy F.; González, Pablo J.; Samsonov, Sergey; Fernández, Jose; Camacho, Antonio

2017-09-01

Because of its proximity to the city of Naples and with a population of nearly 1 million people within its caldera, Campi Flegrei is one of the highest risk volcanic areas in the world. Since the last major eruption in 1538, the caldera has undergone frequent episodes of ground subsidence and uplift accompanied by seismic activity that has been interpreted as the result of a stationary, deeper source below the caldera that feeds shallower eruptions. However, the location and depth of the deeper source is not well-characterized and its relationship to current activity is poorly understood. Recently, a significant increase in the uplift rate has occurred, resulting in almost 13 cm of uplift by 2013 (De Martino et al., 2014; Samsonov et al., 2014b; Di Vito et al., 2016). Here we apply a principal component decomposition to high resolution time series from the region produced by the advanced Multidimensional SBAS DInSAR technique in order to better delineate both the deeper source and the recent shallow activity. We analyzed both a period of substantial subsidence (1993-1999) and a second of significant uplift (2007-2013) and inverted the associated vertical surface displacement for the most likely source models. Results suggest that the underlying dynamics of the caldera changed in the late 1990s, from one in which the primary signal arises from a shallow deflating source above a deeper, expanding source to one dominated by a shallow inflating source. In general, the shallow source lies between 2700 and 3400 m below the caldera while the deeper source lies at 7600 m or more in depth. The combination of principal component analysis with high resolution MSBAS time series data allows for these new insights and confirms the applicability of both to areas at risk from dynamic natural hazards.

Structural Basis for DNA Recognition by the Two-Component Response Regulator RcsB.

Science.gov (United States)

Filippova, Ekaterina V; Zemaitaitis, Bozena; Aung, Theint; Wolfe, Alan J; Anderson, Wayne F

2018-02-27

RcsB is a highly conserved transcription regulator of the Rcs phosphorelay system, a complex two-component signal transduction system (N. Majdalani and S. Gottesman, Annu Rev Microbiol 59:379-405, 2005; A. J. Wolfe, Curr Opin Microbiol 13:204-209, 2010, https://doi.org/10.1016/j.mib.2010.01.002; D. J. Clarke, Future Microbiol 5:1173-1184, 2010, https://doi.org/10.2217/fmb.10.83). RcsB plays an important role in virulence and pathogenicity in human hosts by regulating biofilm formation. RcsB can regulate transcription alone or together with its auxiliary transcription regulators by forming heterodimers. This complexity allows RcsB to regulate transcription of more than 600 bacterial genes in response to different stresses (D. Wang et al., Mol Plant Microbe Interact 25:6-17, 2012, https://doi.org/10.1094/MPMI-08-11-0207). Despite increasing knowledge of RcsB importance, molecular mechanisms that drive the ability of RcsB to control transcription of a large number of genes remain unclear. Here, we present crystal structures of unphosphorylated RcsB in complex with the consensus DNA-binding sequence of 22-mer (DNA22) and 18-mer (DNA18) of the flhDC operon from Escherichia coli determined at 3.15- and 3.37-Å resolution, respectively. The results of our structural analysis combined with the results of in vitro binding assays provide valuable insights to the protein regulatory mechanism, demonstrate how RcsB recognizes target DNA sequences, and reveal a unique oligomeric state that allows RcsB to form homo- and heterodimers. This information will help us understand the complex mechanisms of transcriptional regulation by RcsB in bacteria. IMPORTANCE RcsB is a well-studied two-component response regulator of the Rcs phosphorelay system, conserved within the family Enterobacteriaceae , which includes many pathogens. It is a global regulator, controlling more than 5% of bacterial genes associated with capsule biosynthesis, flagellar biogenesis, cell wall biosynthesis

Optimism and pessimism are related to different components of the stress response in healthy older people.

Science.gov (United States)

Puig-Perez, Sara; Villada, Carolina; Pulopulos, Matias M; Almela, Mercedes; Hidalgo, Vanesa; Salvador, Alicia

2015-11-01

Some personality traits have key importance for health because they can affect the maintenance and evolution of different disorders with a high prevalence in older people, including stress pathologies and diseases. In this study we investigated how two relevant personality traits, optimism and pessimism, affect the psychophysiological response of 72 healthy participants (55 to 76 years old) exposed to either a psychosocial stress task (Trier Social Stress Test, TSST) or a control task; salivary cortisol, heart rate (HR) and situational appraisal were measured. Our results showed that optimism was related to faster cortisol recovery after exposure to stress. Pessimism was not related to the physiological stress response, but it was associated with the perception of the stress task as more difficult. Thus, higher optimism was associated with better physiological adjustment to a stressful situation, while higher pessimism was associated with worse psychological adjustment to stress. These results highlight different patterns of relationships, with optimism playing a more important role in the physiological component of the stress response, and pessimism having a greater effect on situational appraisal. Copyright © 2015 Elsevier B.V. All rights reserved.

Alternate modal combination methods in response spectrum analysis

International Nuclear Information System (INIS)

Bezler, P.; Curreri, J.R.; Wang, Y.K.; Gupta, A.K.

1990-10-01

In piping analyses using the response spectrum method Square Root of the Sum of the Squares (SRSS) with clustering between closely spaced modes is the combination procedure most commonly used to combine between the modal response components. This procedure is simple to apply and normally yields conservative estimates of the time history results. The purpose of this study is to investigate alternate methods to combine between the modal response components. These methods are mathematically based to properly account for the combination between rigid and flexible modal responses as well as closely spaced modes. The methods are those advanced by Gupta, Hadjian and Lindely-Yow to address rigid response modes and the Double Sum Combination (DSC) method and the Complete Quadratic Combination (CQC) method to account for closely spaced modes. A direct comparison between these methods as well as the SRSS procedure is made by using them to predict the response of six piping systems. The results provided by each method are compared to the corresponding time history estimates of results as well as to each other. The degree of conservatism associated with each method is characterized. 19 refs., 16 figs., 10 tabs

The loss of essential oil components induced by the Purge Time in the Pressurized Liquid Extraction (PLE) procedure of Cupressus sempervirens.

Science.gov (United States)

Dawidowicz, Andrzej L; Czapczyńska, Natalia B; Wianowska, Dorota

2012-05-30

The influence of different Purge Times on the effectiveness of Pressurized Liquid Extraction (PLE) of volatile oil components from cypress plant matrix (Cupressus sempervirens) was investigated, applying solvents of diverse extraction efficiencies. The obtained results show the decrease of the mass yields of essential oil components as a result of increased Purge Time. The loss of extracted components depends on the extrahent type - the greatest mass yield loss occurred in the case of non-polar solvents, whereas the smallest was found in polar extracts. Comparisons of the PLE method with Sea Sand Disruption Method (SSDM), Matrix Solid-Phase Dispersion Method (MSPD) and Steam Distillation (SD) were performed to assess the method's accuracy. Independent of the solvent and Purge Time applied in the PLE process, the total mass yield was lower than the one obtained for simple, short and relatively cheap low-temperature matrix disruption procedures - MSPD and SSDM. Thus, in the case of volatile oils analysis, the application of these methods is advisable. Copyright © 2012 Elsevier B.V. All rights reserved.

Effect of time of day on performance, hormonal and metabolic response during a 1000-M cycling time trial.

Directory of Open Access Journals (Sweden)

Alan Lins Fernandes

Full Text Available The aim of this study was to determine the effect of time of day on performance, pacing, and hormonal and metabolic responses during a 1000-m cycling time-trial. Nine male, recreational cyclists visited the laboratory four times. During the 1st visit the participants performed an incremental test and during the 2nd visit they performed a 1000-m cycling familiarization trial. On the 3rd and 4th visits, the participants performed a 1000-m TT at either 8 am or 6 pm, in randomized, repeated-measures, crossover design. The time to complete the time trial was lower in the evening than in the morning (88.2±8.7 versus 94.7±10.9 s, respectively, p0.05, but the norepinephrine response to the exercise was increased in the morning (+46%, p0.05. Our findings suggest that performance was improved in the evening, and it was accompanied by an improved hormonal and metabolic milieu.

Residential response to voluntary time-of-use electricity rates

Energy Technology Data Exchange (ETDEWEB)

Mostafa Baladi, S. [Laurits R. Christensen Associates, Inc. Ames, IA 50011-1070 (United States); Herriges, Joseph A. [Iowa State University, 280D Heady Hall, Department of Economics, Iowa State University, Ames, IA 50011-1070 (United States); Sweeney, Thomas J. [MidAmerican Energy, Des Moines, Iowa (United States)

1998-09-01

The response of residential households to voluntary Time-of-Use (TOU) electricity rates is estimated using data from a recent experiment at Midwest Power Systems of Iowa. The study`s design allows us to examine both the participation decision and the customer`s load pattern changes once the TOU rate structure was in effect. Substitution elasticities between on-peak and off-peak electricity usage are estimated and compared to those obtained in earlier mandatory programs, indicating whether program volunteers are more responsive to TOU pricing than the typical household. Attitudinal questionnaires allow us to examine the role of usage perceptions in program participation

Limited information estimation of the diffusion-based item response theory model for responses and response times.

Science.gov (United States)

Ranger, Jochen; Kuhn, Jörg-Tobias; Szardenings, Carsten

2016-05-01

Psychological tests are usually analysed with item response models. Recently, some alternative measurement models have been proposed that were derived from cognitive process models developed in experimental psychology. These models consider the responses but also the response times of the test takers. Two such models are the Q-diffusion model and the D-diffusion model. Both models can be calibrated with the diffIRT package of the R statistical environment via marginal maximum likelihood (MML) estimation. In this manuscript, an alternative approach to model calibration is proposed. The approach is based on weighted least squares estimation and parallels the standard estimation approach in structural equation modelling. Estimates are determined by minimizing the discrepancy between the observed and the implied covariance matrix. The estimator is simple to implement, consistent, and asymptotically normally distributed. Least squares estimation also provides a test of model fit by comparing the observed and implied covariance matrix. The estimator and the test of model fit are evaluated in a simulation study. Although parameter recovery is good, the estimator is less efficient than the MML estimator. © 2016 The British Psychological Society.

Statistical uncertainty of response characteristic of building-appendage system for spectrum-compatible artificial earthquake motion

International Nuclear Information System (INIS)

Kurosaki, A.; Kozeki, M.

1981-01-01

Spectrum-compatible artificial time histories of ground motions are frequently used for the seismic design of nuclear power plant structures and components. However, statistical uncertainty of the responses of building structures and mechanical components mounted on the building (building-appendage systems) are anticipated, since an artificial time history is no more than one sample from a population of such time histories that match a specified design response spectrum. This uncertainty may spoil the reliability of the seismic design and therefore the extent of the uncertainty of the response characteristic is a matter of great concern. In this paper, above-mentioned uncertainty of the dynamic response characteristics of the building-appendage system to the spectrum-compatible artificial earthquake is investigated. (orig./RW)

Adaptation of Black-Box Software Components

Directory of Open Access Journals (Sweden)

Rolf Andreas Rasenack

2008-01-01

Full Text Available The globalization of the software market leads to crucial problems for software companies. More competition between software companies arises and leads to the force on companies to develop ever newer software products in ever shortened time interval. Therefore the time to market for software systems is shortened and obviously the product life cycle is shortened too. Thus software companies shortened the time interval for research and development. Due to the fact of competition between software companies software products have to develop low-priced and this leads to a smaller return on investment. A big challenge for software companies is the use of an effective research and development process to have these problems under control. A way to control these problems can be the reuse of existing software components and adapt those software components to new functionality or accommodate mismatched interfaces. Complete redevelopment of software products is more expensive and time consuming than to develop software components. The approach introduced here presents novel technique together with a supportive environment that enables developers to cope with the adaptability of black-box software components. A supportive environment will be designed that checks the compatibility of black-box software components with the assistance of their specifications. Generated adapter software components can take over the part of adaptation and advance the functionality. Besides, a pool of software components can be used to compose an application to satisfy customer needs. Certainly this pool of software components consists of black-box software components and adapter software components which can be connected on demand.

A Two Time-scale response of the Southern Ocean to the Ozone Hole: Regional Responses and Mechanisms

Science.gov (United States)

Gnanadesikan, A.; Seviour, W.; Waugh, D.; Pradal, M. A. S.

2016-12-01

The impact of changing ozone on the climate of the Southern Ocean is evaluated using an ensemble of coupled climate models. By imposing a step change from 1860 to 2000 conditions we are able to estimate response functions associated with this change. Two time scales are found, an initial cooling centered in the Southwest Pacific followed by cooling in the Pacific sector and then warming in both sectors. The physical processes that drive this response are different across time periods and locations, as is the sign of the response itself. Initial cooling in the Pacific sector is not just driven by the increased winds pushing cold water northward, but also by a decrease in surface salinity reducing wintertime mixing and increased ice and clouds reflecting more shortwave radiation back to space. The decrease in salinity is primarily driven by a southward shift of precipitation associated with a shifting storm track, coupled with decreased evaporation associated with colder surface temperatures. A subsurface increase in heat associated with this reduction in mixing then upwells along the Antarctic coast, producing a subsequent warming. Similar changes in convective activity occur in the Weddell Sea but are offset in time.

Commercial Building Motor Protection Response Report

Energy Technology Data Exchange (ETDEWEB)

James, Daniel P. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Kueck, John [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2015-06-17

When voltages recover, motors may immediately reenergize and reaccelerate, or delay for a few minutes, or stay stalled. The estimated motor response is given for both the voltage sag magnitude and voltage sag duration. These response estimates are based on experience and available test data. Good data is available for voltage sag response for many components such as relays and contactors, but little data is available for both voltage sag and recovery response. The tables in Appendix A include data from recent voltage sag and recovery tests performed by SCE and BPA on air conditioners and energy management systems. The response of the motor can vary greatly depending on the type of protection and control. The time duration for the voltage sag consists of those times that are of interest for bulk power system modelers.

Phosphorescence lifetimes of organic light-emitting diodes from two-component time-dependent density functional theory

Energy Technology Data Exchange (ETDEWEB)

Kühn, Michael [Institut für Physikalische Chemie, Karlsruher Institut für Technologie, Kaiserstraße 12, 76131 Karlsruhe (Germany); Weigend, Florian, E-mail: florian.weigend@kit.edu [Institut für Physikalische Chemie, Karlsruher Institut für Technologie, Kaiserstraße 12, 76131 Karlsruhe (Germany); Institut für Nanotechnologie, Karlsruher Institut für Technologie, Postfach 3640, 76021 Karlsruhe (Germany)

2014-12-14

“Spin-forbidden” transitions are calculated for an eight-membered set of iridium-containing candidate molecules for organic light-emitting diodes (OLEDs) using two-component time-dependent density functional theory. Phosphorescence lifetimes (obtained from averaging over relevant excitations) are compared to experimental data. Assessment of parameters like non-distorted and distorted geometric structures, density functionals, relativistic Hamiltonians, and basis sets was done by a thorough study for Ir(ppy){sub 3} focussing not only on averaged phosphorescence lifetimes, but also on the agreement of the triplet substate structure with experimental data. The most favorable methods were applied to an eight-membered test set of OLED candidate molecules; Boltzmann-averaged phosphorescence lifetimes were investigated concerning the convergence with the number of excited states and the changes when including solvent effects. Finally, a simple model for sorting out molecules with long averaged phosphorescence lifetimes is developed by visual inspection of computationally easily achievable one-component frontier orbitals.

Fast response time alcohol gas sensor using nanocrystalline F