A Data-Driven Response Virtual Sensor Technique with Partial Vibration Measurements Using Convolutional Neural Network

Science.gov (United States)

Sun, Shan-Bin; He, Yuan-Yuan; Zhou, Si-Da; Yue, Zhen-Jiang

2017-01-01

Measurement of dynamic responses plays an important role in structural health monitoring, damage detection and other fields of research. However, in aerospace engineering, the physical sensors are limited in the operational conditions of spacecraft, due to the severe environment in outer space. This paper proposes a virtual sensor model with partial vibration measurements using a convolutional neural network. The transmissibility function is employed as prior knowledge. A four-layer neural network with two convolutional layers, one fully connected layer, and an output layer is proposed as the predicting model. Numerical examples of two different structural dynamic systems demonstrate the performance of the proposed approach. The excellence of the novel technique is further indicated using a simply supported beam experiment comparing to a modal-model-based virtual sensor, which uses modal parameters, such as mode shapes, for estimating the responses of the faulty sensors. The results show that the presented data-driven response virtual sensor technique can predict structural response with high accuracy. PMID:29231868

A Data-Driven Response Virtual Sensor Technique with Partial Vibration Measurements Using Convolutional Neural Network.

Science.gov (United States)

Sun, Shan-Bin; He, Yuan-Yuan; Zhou, Si-Da; Yue, Zhen-Jiang

2017-12-12

Measurement of dynamic responses plays an important role in structural health monitoring, damage detection and other fields of research. However, in aerospace engineering, the physical sensors are limited in the operational conditions of spacecraft, due to the severe environment in outer space. This paper proposes a virtual sensor model with partial vibration measurements using a convolutional neural network. The transmissibility function is employed as prior knowledge. A four-layer neural network with two convolutional layers, one fully connected layer, and an output layer is proposed as the predicting model. Numerical examples of two different structural dynamic systems demonstrate the performance of the proposed approach. The excellence of the novel technique is further indicated using a simply supported beam experiment comparing to a modal-model-based virtual sensor, which uses modal parameters, such as mode shapes, for estimating the responses of the faulty sensors. The results show that the presented data-driven response virtual sensor technique can predict structural response with high accuracy.

Use of structured personality survey techniques to indicate operator response to stressful situations

International Nuclear Information System (INIS)

Waller, M.A.

1990-01-01

Under given circumstances, a person will tend to operate in one of four dominant orientations: (1) to perform tasks; (2) to achieve consensus; (3) to achieve understanding, or (4) to maintain structure. Historically, personality survey techniques, such as the Myers-Briggs type indicator, have been used to determine these tendencies. While these techniques can accurately reflect a person's orientation under normal social situations, under different sets of conditions, the same person may exhibit other tendencies, displaying a similar or entirely different orientation. While most do not exhibit extreme tendencies or changes of orientation, the shift in personality from normal to stressful conditions can be rather dramatic, depending on the individual. Structured personality survey techniques have been used to indicate operator response to stressful situations. These techniques have been extended to indicate the balance between orientations that the control room team has through the various levels of cognizance

A new technique of characterization of intrapixel response dedicated to astronomical detectors

International Nuclear Information System (INIS)

Ketchazo, C.; Viale, T.; Boulade, O.; Druart, G.; Moreau, V.; Mugnier, L.; Dubrueil, D.; Derelle, S.; Ronayette, S.; Guérineau, N.; Berthé, M.

2015-01-01

This paper is devoted to the presentation of a new technique of characterization of the intra-pixel sensitivity variations (IPSVs) of astronomical detectors. The IPSV is the spatial variation of the pixel response function (PRF). In the case of under-sampled instruments for high quality imaging and accurate photometry, IPSV can contribute to the instrument global error and it should be considered carefully. Our measurement technique is based in the Fourier transform (FT) approach. It consists into the sampling of the pixel transfer function (PTF) by projecting high-resolution periodic patterns onto the whole sensor without classic optics but using the self-imaging property (the Talbot effect) of a continuously self imaging grating (CSIG) illuminated by a plane wave. The PRF is determined by computing the inverse FT. Our measurement technique permits to determine the PRF with a resolution of pixel/10 (10 times Nyquist frequency)

Conventional and conformal technique of external beam radiotherapy in locally advanced cervical cancer: Dose distribution, tumor response, and side effects

Science.gov (United States)

Mutrikah, N.; Winarno, H.; Amalia, T.; Djakaria, M.

2017-08-01

The objective of this study was to compare conventional and conformal techniques of external beam radiotherapy (EBRT) in terms of the dose distribution, tumor response, and side effects in the treatment of locally advanced cervical cancer patients. A retrospective cohort study was conducted on cervical cancer patients who underwent EBRT before brachytherapy in the Radiotherapy Department of Cipto Mangunkusumo Hospital. The prescribed dose distribution, tumor response, and acute side effects of EBRT using conventional and conformal techniques were investigated. In total, 51 patients who underwent EBRT using conventional techniques (25 cases using Cobalt-60 and 26 cases using a linear accelerator (LINAC)) and 29 patients who underwent EBRT using conformal techniques were included in the study. The distribution of the prescribed dose in the target had an impact on the patient’s final response to EBRT. The complete response rate of patients to conformal techniques was significantly greater (58%) than that of patients to conventional techniques (42%). No severe acute local side effects were seen in any of the patients (Radiation Therapy Oncology Group (RTOG) grades 3-4). The distribution of the dose and volume to the gastrointestinal tract affected the proportion of mild acute side effects (RTOG grades 1-2). The urinary bladder was significantly greater using conventional techniques (Cobalt-60/LINAC) than using conformal techniques at 72% and 78% compared to 28% and 22%, respectively. The use of conformal techniques in pelvic radiation therapy is suggested in radiotherapy centers with CT simulators and 3D Radiotherapy Treatment Planning Systems (RTPSs) to decrease some uncertainties in radiotherapy planning. The use of AP/PA pelvic radiation techniques with Cobalt-60 should be limited in body thicknesses equal to or less than 18 cm. When using conformal techniques, delineation should be applied in the small bowel, as it is considered a critical organ according to RTOG

Pressure integration technique for predicting wind-induced response in high-rise buildings

Directory of Open Access Journals (Sweden)

Aly Mousaad Aly

2013-12-01

Full Text Available This paper presents a procedure for response prediction in high-rise buildings under wind loads. The procedure is illustrated in an application example of a tall building exposed to both cross-wind and along-wind loads. The responses of the building in the lateral directions combined with torsion are estimated simultaneously. Results show good agreement with recent design standards; however, the proposed procedure has the advantages of accounting for complex mode shapes, non-uniform mass distribution, and interference effects from the surrounding. In addition, the technique allows for the contribution of higher modes. For accurate estimation of the acceleration response, it is important to consider not only the first two lateral vibrational modes, but also higher modes. Ignoring the contribution of higher modes may lead to underestimation of the acceleration response; on the other hand, it could result in overestimation of the displacement response. Furthermore, the procedure presented in this study can help decision makers, involved in a tall building design/retrofit to choose among innovative solutions like aerodynamic mitigation, structural member size adjustment, damping enhancement, and/or materials change, with an objective to improve the resiliency and the serviceability under extreme wind actions.

Water spray cooling technique applied on a photovoltaic panel: The performance response

International Nuclear Information System (INIS)

Nižetić, S.; Čoko, D.; Yadav, A.; Grubišić-Čabo, F.

2016-01-01

Highlights: • An experimental study was conducted on a monocrystalline photovoltaic panel (PV). • A water spray cooling technique was implemented to determine PV panel response. • The experimental results showed favorable cooling effect on the panel performance. • A feasibility aspect of the water spray cooling technique was also proven. - Abstract: This paper presents an alternative cooling technique for photovoltaic (PV) panels that includes a water spray application over panel surfaces. An alternative cooling technique in the sense that both sides of the PV panel were cooled simultaneously, to investigate the total water spray cooling effect on the PV panel performance in circumstances of peak solar irradiation levels. A specific experimental setup was elaborated in detail and the developed cooling system for the PV panel was tested in a geographical location with a typical Mediterranean climate. The experimental result shows that it is possible to achieve a maximal total increase of 16.3% (effective 7.7%) in electric power output and a total increase of 14.1% (effective 5.9%) in PV panel electrical efficiency by using the proposed cooling technique in circumstances of peak solar irradiation. Furthermore, it was also possible to decrease panel temperature from an average 54 °C (non-cooled PV panel) to 24 °C in the case of simultaneous front and backside PV panel cooling. Economic feasibility was also determined for of the proposed water spray cooling technique, where the main advantage of the analyzed cooling technique is regarding the PV panel’s surface and its self-cleaning effect, which additionally acts as a booster to the average delivered electricity.

Characterization of Deficiencies in the Frequency Domain Forced Response Analysis Technique for Turbine Bladed Disks

Science.gov (United States)

Brown, Andrew M.; Schmauch, Preston

2012-01-01

Turbine blades in rocket and jet engine turbomachinery experience enormous harmonic loading conditions. These loads result from the integer number of upstream and downstream stator vanes as well as the other turbine stages. The standard technique for forced response analysis to assess structural integrity is to decompose a CFD generated flow field into its harmonic components, and to then perform a frequency response analysis at the problematic natural frequencies. Recent CFD analysis and water-flow testing at NASA/MSFC, though, indicates that this technique may miss substantial harmonic and non-harmonic excitation sources that become present in complex flows. These complications suggest the question of whether frequency domain analysis is capable of capturing the excitation content sufficiently. Two studies comparing frequency response analysis with transient response analysis, therefore, have been performed. The first is of a bladed disk with each blade modeled by simple beam elements. It was hypothesized that the randomness and other variation from the standard harmonic excitation would reduce the blade structural response, but the results showed little reduction. The second study was of a realistic model of a bladed-disk excited by the same CFD used in the J2X engine program. The results showed that the transient analysis results were up to 10% higher for "clean" nodal diameter excitations and six times larger for "messy" excitations, where substantial Fourier content around the main harmonic exists.

A Framework for Prediction of Response to HCV Therapy Using Different Data Mining Techniques

Directory of Open Access Journals (Sweden)

Enas M. F. El Houby

2014-01-01

Full Text Available Hepatitis C which is a widely spread disease all over the world is a fatal liver disease caused by Hepatitis C Virus (HCV. The only approved therapy is interferon plus ribavirin. The number of responders to this treatment is low, while its cost is high and side effects are undesirable. Treatment response prediction will help in reducing the patients who suffer from the side effects and high costs without achieving recovery. The aim of this research is to develop a framework which can select the best model to predict HCV patients’ response to the treatment of HCV from clinical information. The framework contains three phases which are preprocessing phase to prepare the data for applying Data Mining (DM techniques, DM phase to apply different DM techniques, and evaluation phase to evaluate and compare the performance of the built models and select the best model as the recommended one. Different DM techniques had been applied which are associative classification, artificial neural network, and decision tree to evaluate the framework. The experimental results showed the effectiveness of the framework in selecting the best model which is the model built by associative classification using histology activity index, fibrosis stage, and alanine amino transferase.

A filter technique for optimising the photon energy response of a silicon pin diode dosemeter

International Nuclear Information System (INIS)

Olsher, R.H.; Eisen, Y.

1996-01-01

Unless they are energy compensated, silicon PIN diodes used in electronic pocket dosemeters, have significant over-response below 200 keV. Siemens is using three diodes in parallel with individual filters to produce excellent energy and angular response. An algorithm based on the photon spectrum of a single diode could be used to flatten the energy response. The commercial practice is to use a single diode with a simple filter to flatten the energy response, despite the mediocre low energy photon. The filter technique with an opening has been used for energy compensating GM detectors and proportional counters and a new variation of it has been investigated which compensates the energy response of a silicon PIN diode and maintains an extended low energy response. It uses a composite filter of two or more materials with several openings whose individual area is in the range of 15% to 25% of the diode's active area. One opening is centred over the diode's active area and others are located at the periphery of the active area to preserve a good polar response to ±45 o . Monte Carlo radiation transport methods were used to simulate the coupled electron-photon transport through a Hamamatsu S2506-01 diode and to determine the energy response of the diode for a variety of filters. In current mode, the resultant dosemeter energy response relative to air dose was within -15% and +30% for 0 o incidence over the energy range from 15 keV to 1 MeV. In pulse mode, the resultant dosemeter energy response was within -25% and +50% for 0 o incidence over the energy range from 30 keV to 10 MeV. For ±45 o incidence, the energy response was within -25% and +40% from 40 keV to 10 MeV. Theoretical viability of the filter technique has been shown in this work (Author)

Enhancing spill prevention and response preparedness through quality control techniques

International Nuclear Information System (INIS)

Jones, M.A.; Butts, R.L.; Pickering, T.H.; Lindsay, J.R.; McCully, B.S.

1993-01-01

The year 1990 saw passage of federal and state oil spill legislation directing the US Environmental Protection Agency and the Florida Department of Environmental Regulation to require on shore bulk petroleum storage facilities to improve their oil spill response and prevention capabilities. The Florida Power ampersand Light Company (FPL), to address concerns arising out of several recent significant spills which had occurred worldwide, and to examine its current situation with regard compliance with the new laws, formed a quality improvement interdepartmental task team in July 1989. Its mission was to reduce the potential for oil spills during waterborne transportation between FPL's fuel oil terminals and its power plants and during transfer and storage of oil at these facilities. Another objective of the team was to enhance the company's spill response preparedness. Using quality control tools and reliability techniques, the team conducted a detailed analysis of seven coastal power plants and five fuel oil terminal facilities. This analysis began with the development of cause-and-effect diagrams designed to identify the root causes of spills so that corrective and preventive actions could be taken. These diagram are constructed by listing possible causes of oil spills under various major categories of possible system breakdown, such as man, method, equipment, and materials. Next, potential root causes are identified and then verified. The team identified the occurrence of surface water oil spill and reduced spill response capability as primary concerns and accordingly constructed cause-and-effect diagrams for both components. Lack of proper procedures, failure of control equipment, and inadequate facility design were identified as potential root causes leading to surface water oil spills. Lack of proper procedures, an inconsistent training program, and response equipment limitations were identified as potential root causes affecting oil spill response capabilities

Characterization of Deficiencies in the Frequency Domain Forced Response Analysis Technique for Supersonic Turbine Bladed Disks

Science.gov (United States)

Brown, Andrew M.; Schmauch, Preston

2011-01-01

Turbine blades in rocket and jet engine turbomachinery experience enormous harmonic loading conditions. These loads result from the integer number of upstream and downstream stator vanes as well as the other turbine stages. Assessing the blade structural integrity is a complex task requiring an initial characterization of whether resonance is possible and then performing a forced response analysis if that condition is met. The standard technique for forced response analysis in rocket engines is to decompose a CFD-generated flow field into its harmonic components, and to then perform a frequency response analysis at the problematic natural frequencies. Recent CFD analysis and water-flow testing at NASA/MSFC, though, indicates that this technique may miss substantial harmonic and non-harmonic excitation sources that become present in complex flows. A substantial effort has been made to account for this denser spatial Fourier content in frequency response analysis (described in another paper by the author), but the question still remains whether the frequency response analysis itself is capable of capturing the excitation content sufficiently. Two studies comparing frequency response analysis with transient response analysis, therefore, of bladed-disks undergoing this complex flow environment have been performed. The first is of a bladed disk with each blade modeled by simple beam elements. Six loading cases were generated by varying a baseline harmonic excitation in different ways based upon cold-flow testing from Heritage Fuel Air Turbine Test. It was hypothesized that the randomness and other variation from the standard harmonic excitation would reduce the blade structural response, but the results showed little reduction. The second study was of a realistic model of a bladed-disk excited by the same CFD used in the J2X engine program. It was hypothesized that enforcing periodicity in the CFD (inherent in the frequency response technique) would overestimate the

Controlled trial of the effect of length, incentives, and follow-up techniques on response to a mailed questionnaire.

Science.gov (United States)

Hoffman, S C; Burke, A E; Helzlsouer, K J; Comstock, G W

1998-11-15

Mailed questionnaires are an economical method of data collection for epidemiologic studies, but response tends to be lower than for telephone or personal interviews. As part of a follow-up study of volunteers who provided a brief health history and blood sample for a blood specimen bank in 1989, the authors conducted a controlled trial of the effect of length, incentives, and follow-up techniques on response to a mailed questionnaire. Interventions tested included variations on length of the questionnaire, effect of a monetary incentive, and effect of a postcard reminder versus a letter accompanied by a second questionnaire. Response was similar for the short (16-item, 4-page) and long (76-item, 16-page) questionnaire groups. The non-monetary [corrected] incentive did not improve the frequency of response. The second mailing of a questionnaire was significantly better than a postcard reminder in improving responses (23% vs. 10%). It is important to systematically test marketing principles to determine which techniques are effective in increasing response to mailed questionnaires for epidemiologic studies.

The modifying effect of anesthetic technique on the metabolic and endocrine responses to anesthesia and surgery

DEFF Research Database (Denmark)

Kehlet, H

1988-01-01

and the widespread use of the term "stress free anesthesia" in surgery is therefore not valid. However, continuous administration of local anesthetic agents in the epidural space is the most effective technique in so far as reduction of the stress response is concerned. The clinical implication of a variable...... reduction in the stress response to surgery by different anesthetic techniques remains largely unsettled, since only few controlled studies have been published on the clinical effects of pain relief and general anesthesia. However, a vast amount of data exist from controlled studies comparing regional...... anesthesia with local anesthetics and general anesthesia. The cumulative experience from these studies have demonstrated an advantageous effect on postoperative morbidity parameters such as blood loss, postoperative thromboembolic complications, pulmonary infective complications, gastrointestinal motility...

Alzheimer's Disease Assessment: A Review and Illustrations Focusing on Item Response Theory Techniques.

Science.gov (United States)

Balsis, Steve; Choudhury, Tabina K; Geraci, Lisa; Benge, Jared F; Patrick, Christopher J

2018-04-01

Alzheimer's disease (AD) affects neurological, cognitive, and behavioral processes. Thus, to accurately assess this disease, researchers and clinicians need to combine and incorporate data across these domains. This presents not only distinct methodological and statistical challenges but also unique opportunities for the development and advancement of psychometric techniques. In this article, we describe relatively recent research using item response theory (IRT) that has been used to make progress in assessing the disease across its various symptomatic and pathological manifestations. We focus on applications of IRT to improve scoring, test development (including cross-validation and adaptation), and linking and calibration. We conclude by describing potential future multidimensional applications of IRT techniques that may improve the precision with which AD is measured.

Characterization of the host response to the myxosporean parasite, Ceratomyxa shasta (Noble), by histology, scanning electron microscopy, and immunological techniques

Science.gov (United States)

Bartholomew, J.L.; Smith, C.E.; Rohovec, J.S.; Fryer, J.L.

1989-01-01

The tissue response of Salmo gairdneri Richardson, against the myxosporean parasite. Ceratomyxa shasta (Noble), was investigated using histological techniques, scanning electron microscopy and immunological methods. The progress of infection in C. shasta-susceptible and resistant steelhead and rainbow trout was examined by standard histological techniques and by indirect fluorescent antibody methods using monoclonal antibodies directed against C. shasta antigens. Trophozoite stages were first observed in the posterior intestine and there was indication that resistance was due to the inability of the parasite to penetrate this tissue rather than to an inflammatory response. Examination of a severely infected intestine by scanning electron microscopy showed extensive destruction of the mucosal folds of the posterior intestine. Western blotting and indirect fluorescent antibody techniques were used to investigate the immunological component of the host response. No antibodies specific for C. shasta were detected by either method.

Experimental and mathematical simulation techniques for determining an in-situ response testing method for neutron sensors used in reactor power plant protection systems

International Nuclear Information System (INIS)

Behbahani, A.

1983-01-01

An analytical neutron sensor response model and methods for transient response measurements of neutron sensors (compensated ionization chamber), including possible in-situ techniques have been developed and evaluated to meet the provisions of Draft Standard ISA Sd67.06, IEEE 338-1977, and NRC Guide 1.118. One in-situ method requires the perturbation of the high voltage detector (sensor) power supply and measurement of the sensor response. The response to a perturbation of the power supply is related to the response of the sensor to a transient change in neutron flux. Random signal analysis is another in-situ technique to monitor the neutron sensor response. In this method the power spectrum of the inherent fluctuations from the neutron sensor output (current in CIC) are measured and evaluated. Transient response techniques (including in-situ methods) are experimentally and analytically evaluated to identify the mechanisms which may cause degradation in the response of the neutron sensors. The objective of the experimental evaluation was to correlate the measured response time using transient radiation flux changes and power supply perturbation. The objective of the analytical model of the different sensor response was to predict response time and degradation mechanisms

Isotope-based immunological techniques. Their use in assessment of immune competence and the study of immune responses to pathogens

International Nuclear Information System (INIS)

Duffus, W.P.H.

1984-01-01

The influence of isotope-based techniques on both assessment of immune competence and immune response to pathogens is discussed. Immunodeficiencies acquired as a result of factors like malnutrition and concomitant disease can severely affect not only attempts to intensify and improve production but also successful immune response against important vaccines such as rinderpest and foot-and-mouth disease. Isotope-based techniques, with their accuracy, speed and small sample volume, are ideally suited for assessing immunocompetence. One of the main drawbacks remains antigen purity, an area where research should now be concentrated. Lymphocyte transformation is widely used to assess cell-mediated immuno-competence but techniques to assess biological functions such as phagocytosis and cell-mediated cytotoxicity could more usefully reflect immune status. These latter techniques utilize isotopes such as 3 H, 14 C, 32 P and 125 I. Investigation of specific cell-mediated immune response often requires a labelled target. Suitable isotopes such as 51 Cr, 99 Tcsup(m), 75 Se and 3 H are compared for their capacity to label both mammalian and parasite targets. Suggestions are made on a number of areas of research that might usefully be encouraged and supported in order to improve applied veterinary immunology in tropical countries. (author)

Temporal impulse and step responses of the human eye obtained psychophysically by means of a drift-correcting perturbation technique

NARCIS (Netherlands)

Roufs, J.A.J.; Blommaert, F.J.J.

1981-01-01

Internal impulse and step responses are derived from the thresholds of short probe flashes by means of a drift-correcting perturbation technique. The approach is based on only two postulated systems properties: quasi-linearity and peak detection. A special feature of the technique is its strong

System Response Analysis and Model Order Reduction, Using Conventional Method, Bond Graph Technique and Genetic Programming

Directory of Open Access Journals (Sweden)

Lubna Moin

2009-04-01

Full Text Available This research paper basically explores and compares the different modeling and analysis techniques and than it also explores the model order reduction approach and significance. The traditional modeling and simulation techniques for dynamic systems are generally adequate for single-domain systems only, but the Bond Graph technique provides new strategies for reliable solutions of multi-domain system. They are also used for analyzing linear and non linear dynamic production system, artificial intelligence, image processing, robotics and industrial automation. This paper describes a unique technique of generating the Genetic design from the tree structured transfer function obtained from Bond Graph. This research work combines bond graphs for model representation with Genetic programming for exploring different ideas on design space tree structured transfer function result from replacing typical bond graph element with their impedance equivalent specifying impedance lows for Bond Graph multiport. This tree structured form thus obtained from Bond Graph is applied for generating the Genetic Tree. Application studies will identify key issues and importance for advancing this approach towards becoming on effective and efficient design tool for synthesizing design for Electrical system. In the first phase, the system is modeled using Bond Graph technique. Its system response and transfer function with conventional and Bond Graph method is analyzed and then a approach towards model order reduction is observed. The suggested algorithm and other known modern model order reduction techniques are applied to a 11th order high pass filter [1], with different approach. The model order reduction technique developed in this paper has least reduction errors and secondly the final model retains structural information. The system response and the stability analysis of the system transfer function taken by conventional and by Bond Graph method is compared and

Dosimetric evaluation of the response of the TLD-100 dosemeters in the IMRT technique by 'Step and Shoot'

International Nuclear Information System (INIS)

Vasquez, J.; Benavides, S.O.

2005-01-01

We show the results of the dosimetry response of LiF thermoluminescent crystals: TLD-100, where they were radiated in a linear accelerator Siemens Primus Hl using the Intensity Modulated Radiation Therapy (IMRT) by step and shoot technique. Previous to the crystals calibration and response evaluation, the acceptation procedures recommended by the TG-53 protocol for validation of the technique were carried out. The planning system utilized was the Theraplan Plus 3.8, using the algorithm of Pencil Kernel. The register and verification system was Lantis 5.2. The response curve of dose versus charge was obtained from the readings of the TLD in a Harshaw 3500. The crystals were radiated in a Bench- Marck phantom with doses previously determined by using ionization chambers for square radiation fields, in a beam with a 0.68 TPR20,10 corresponding to 6 MV of energy. We compare the response of these through of radiation of segmented fields in a Anthropomorphic phantom and the calculated doses by the planning system. The results obtained in the crystals response show deviations less than 5 % between the measured dose and the calculated dose in the zones of low gradient. It allows its implementation like routine control of quality by IMRT. (Author)

The effects of soil-structure interaction modeling techniques on in-structure response spectra

International Nuclear Information System (INIS)

Johnson, J.J.; Wesley, D.A.; Almajan, I.T.

1977-01-01

The structure considered for this investigation consisted of the reactor containment building (RCB) and prestressed concrete reactor vessel (PCRV) for a HTGR plant. A conventional lumped-mass dynamic model in three dimensions was used in the study. The horizontal and vertical response, which are uncoupled due to the symmetry of the structure, were determined for horizontal and vertical excitation. Five different site conditions ranging from competent rock to a soft soil site were considered. The simplified approach to the overall plant analysis utilized stiffness proportional composite damping with a limited amount of soil damping consistent with US NRC regulatory guidelines. Selected cases were also analyzed assuming a soil damping value approximating the theoretical value. The results from the simplified approach were compared to those determined by rigorously coupling the structure to a frequency independent half-space representation of the soil. Finally, equivalent modal damping ratios were found by matching the frequency response at a point within the coupled soil-structure system determined by solution of the coupled and uncoupled equations of motion. The basis for comparison of the aforementioned techniques was the response spectra at selected locations within the soil-structure system. Each of the five site conditions was analyzed and in-structure response spectra were generated. The response spectra were combined to form a design envelope which encompasses the entire range of site parameters. Both the design envelopes and the site-by-site results were compared

Generation of response functions of a NaI detector by using an interpolation technique

International Nuclear Information System (INIS)

Tominaga, Shoji

1983-01-01

A computer method is developed for generating response functions of a NaI detector to monoenergetic γ-rays. The method is based on an interpolation between measured response curves by a detector. The computer programs are constructed for Heath's response spectral library. The principle of the basic mathematics used for interpolation, which was reported previously by the author, et al., is that response curves can be decomposed into a linear combination of intrinsic-component patterns, and thereby the interpolation of curves is reduced to a simple interpolation of weighting coefficients needed to combine the component patterns. This technique has some advantages of data compression, reduction in computation time, and stability of the solution, in comparison with the usual functional fitting method. The processing method of segmentation of a spectrum is devised to generate useful and precise response curves. A spectral curve, obtained for each γ-ray source, is divided into some regions defined by the physical processes, such as the photopeak area, the Compton continuum area, the backscatter peak area, and so on. Each segment curve then is processed separately for interpolation. Lastly the estimated curves to the respective areas are connected on one channel scale. The generation programs are explained briefly. It is shown that the generated curve represents the overall shape of a response spectrum including not only its photopeak but also the corresponding Compton area, with a sufficient accuracy. (author)

The application of remote sensing techniques to create a Black Sea coastal response strategy for oil spill response

International Nuclear Information System (INIS)

Urban, R.; Hanlon, W.

1998-01-01

The application of remote satellite imaging, coupled with Geographic Information System (GIS) technology has been used to create coastal maps enhanced with environmental information. The use of such techniques for oil spill response requires the development of practical applications to assist responders with real-time decision making. In a joint effort with regional navies for Black Sea spill contingency planning, the US Navy has developed methods by which a quick, accurate, and economical application of existing technology can be used to produce data rich maps for a large area of interest. This combines various existing techniques to create practical applications and usable documents for oil spill planners and responders. Existing environmental data on a selected area of the Black Sea coastal zone was collected and this information was sorted, harmonized and transposed onto a rectified multispectral satellite image of the area in a GIS format. Multispectral analysis was performed on the image to locate environmentally distinct zones. The resulting multi-layered GIS map provides a useful representation of coastal environmental sensitivities, and in many ways surpasses conventional GIS systems. The satellite image provides an accurate and realtime map of the area while the multispectral data precisely locates common ecosystems, such as wetlands and forests. This allows for the rapid prioritization of coastal areas and the ability to pinpoint specific areas for protection. The resulting process provides emergency responders the ability to quickly and economically create a data rich GIS. This system will provide reliable, timely information for protection strategies, identifying environmental and public risks, and offer a basis by which to measure spill impacts and recovery techniques, especially in areas where environmental reference data is limited. (author)

The cardiovascular responses of male subjects to kung fu techniques. Expert/novice paradigm.

Science.gov (United States)

Jones, M A; Unnithan, V B

1998-12-01

The primary aim was to assess cardiovascular responses of expert and novice subjects to kung fu techniques. It was hypothesised that experienced subjects would demonstrate improved economy of movement during the techniques, evidenced by reduced exercise intensity. a comparative design was established utilising two groups; experienced (group E), and novice (group N). the experimentation took place under laboratory conditions, but was designed to maximise external validity. the only preselection variables were regular attendance at training and experience. Nine experienced males (group E, exp 9.5 +/- 5.2 yrs) and nine novice males (group N, exp 1.2 +/- 0.1 yrs) participated. The only exclusion guidelines were contraindications to participate within a maximal test, no subjects were excluded upon this basis. N/A. each subject participated in three kung fu protocols (forms, kicking and punching). Each protocol, randomly allocated, consisted of ten work (30 sec) and ten rest periods (30 sec). MEASURES taken during the protocols were heart rate (HR) and oxygen consumption (VO2). These were expressed as a percentage of maximal values to reflect exercise intensity. During both the form protocol and punching protocol group E were found to be working at a significantly (p kung fu techniques differ depending upon experience level. It is difficult to directly relate this to improved economy since work output could not be accurately quantified. It was also found that kung fu protocols elicited exercise intensity into the cardiovascular training zone.

Temporal impulse and step responses of the human eye obtained psychophysically by means of a drift-correcting perturbation technique

OpenAIRE

Roufs, J.A.J.; Blommaert, F.J.J.

1981-01-01

Internal impulse and step responses are derived from the thresholds of short probe flashes by means of a drift-correcting perturbation technique. The approach is based on only two postulated systems properties: quasi-linearity and peak detection. A special feature of the technique is its strong reduction of the concealing effect of sensitivity drift within and between sessions. Results were found to be repeatable, even after about one year. For a 1° foveal disk at 1200 td stationary level, im...

Lysis solution composition and non-linear dose-response to ionizing radiation in the non-denaturing DNA filter elution technique

International Nuclear Information System (INIS)

Radford, I.R.

1990-01-01

The suggestion by Okayasu and Iliakis (1989) that the non-linear dose-response curve, obtained with the non-denaturing filter elution technique for mammalian cells exposed to low-LET radiation, is the result of a technical artefact, was not confirmed. (author)

Applying modern psychometric techniques to melodic discrimination testing: Item response theory, computerised adaptive testing, and automatic item generation.

Science.gov (United States)

Harrison, Peter M C; Collins, Tom; Müllensiefen, Daniel

2017-06-15

Modern psychometric theory provides many useful tools for ability testing, such as item response theory, computerised adaptive testing, and automatic item generation. However, these techniques have yet to be integrated into mainstream psychological practice. This is unfortunate, because modern psychometric techniques can bring many benefits, including sophisticated reliability measures, improved construct validity, avoidance of exposure effects, and improved efficiency. In the present research we therefore use these techniques to develop a new test of a well-studied psychological capacity: melodic discrimination, the ability to detect differences between melodies. We calibrate and validate this test in a series of studies. Studies 1 and 2 respectively calibrate and validate an initial test version, while Studies 3 and 4 calibrate and validate an updated test version incorporating additional easy items. The results support the new test's viability, with evidence for strong reliability and construct validity. We discuss how these modern psychometric techniques may also be profitably applied to other areas of music psychology and psychological science in general.

Development of criteria for evaluating clinical response in thyroid eye disease using a modified Delphi technique

DEFF Research Database (Denmark)

Douglas, Raymond S; Tsirbas, Angelo; Gordon, Mark

2009-01-01

OBJECTIVE: To identify components of a provisional clinical response index for thyroid eye disease using a modified Delphi technique. METHODS: The International Thyroid Eye Disease Society conducted a structured, 3-round Delphi exercise establishing consensus for a core set of measures for clinical...... parsed into 11 domains for the Delphi surveys. Eighty-four respondents participated in the Delphi 1 survey, providing 220 unique items. Ninety-two members (100% of the respondents from Delphi 1 plus 8 new participants) responded in Delphi 2 and rated the same 220 items. Sixty-four members (76......% of participants) rated 153 criteria in Delphi 3 (67 criteria were excluded because of redundancy). Criteria with a mean greater than 6 (1 = least appropriate to 9 = most appropriate) were further evaluated by the nominal group technique and provisional core measures were chosen. CONCLUSIONS: Using a Delphi...

Comparison of Residence Time Distributions of Liquid for Different Types of Input Signal Using a Stimulus-Response Technique

Czech Academy of Sciences Publication Activity Database

Čermáková, Jiřina; Siyakatshana, N.; Šilar, F.; Kudrna, V.; Jahoda, M.; Machoň, V.

2003-01-01

Roč. 57, č. 6 (2003), s. 427-431 ISSN 0366-6352. [International Conference of Slovak Society of Chemical Engineering /30./. Tatranské Matliare, 26.05.2003-30.05.2003] Institutional research plan: CEZ:AV0Z4072921 Keywords : stirred tank * stimulus-response technique * residence time distribution Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 0.226, year: 2003

RESPONSE OF SELECTED LOCAL PLANTAIN CULTIVARS TO PIBS (PLANTS ISSUS DE BOURGEONS SECONDAIRES TECHNIQUE

Directory of Open Access Journals (Sweden)

Beloved Mensah DZOMEKU

2014-12-01

Full Text Available One major constraint to plantain production has been inadequate healthy planting materials at the time of planting. Several technologies for multiplying healthy planting materials exist but could not meet farmers’ demand. A study was conducted to assess the performance of various landraces plantain to plants issus de bourgeons secondaires (PIBS technique. Five cultivars of Musa sapientum (Apantu (False Horn, Asamienu (True Horn, Oniaba (intermediate French plantain and FHIA-21 (tetraploid hybrid plantain were tested to determine their response to the PIBS technique. Sword suckers of each cultivar with weight of between 0.2-0.5 kg were prepared and buried in fine sawdust in a humidity chamber built using transparent polyethylene sheets. Results at harvest showed that removal of rooted sprouts started three weeks after planting and every week thereafter for eight weeks. The intermediate French plantain cultivar (Oniaba produced the least average number (about 20 of healthy planting. Apantu (False Horn produced an average of about 75 healthy planting materials. The hybrid FHIA-21 on the other hand generated an average of about 85 healthy planting materials. Asamienu (True Horn produced the highest healthy seedlings of about 90 healthy planting materials. The results revealed that the leaf scar carries a primary bud at the intersection of each leaf sheath and several eyes along the entire length of the leaf sheath which could not have developed into suckers. However, with this technique the eyes could be activated to sprout as healthy planting materials. The technique proved as an efficient method of multiplying healthy planting materials for plantain and could thus be recommended for adoption not only by peasant farmers but also to others who could become commercial seed producers. But there will be a need for certification guidelines for seed growing systems.

Solving eigenvalue response matrix equations with nonlinear techniques

International Nuclear Information System (INIS)

Roberts, Jeremy A.; Forget, Benoit

2014-01-01

Highlights: • High performance solvers were applied within ERMM for the first time. • Accelerated fixed-point methods were developed that reduce computational times by 2–3. • A nonlinear, Newton-based ERMM led to similar improvement and more robustness. • A 3-D, SN-based ERMM shows how ERMM can apply fine-mesh methods to full-core analysis. - Abstract: This paper presents new algorithms for use in the eigenvalue response matrix method (ERMM) for reactor eigenvalue problems. ERMM spatially decomposes a domain into independent nodes linked via boundary conditions approximated as truncated orthogonal expansions, the coefficients of which are response functions. In its simplest form, ERMM consists of a two-level eigenproblem: an outer Picard iteration updates the k-eigenvalue via balance, while the inner λ-eigenproblem imposes neutron balance between nodes. Efficient methods are developed for solving the inner λ-eigenvalue problem within the outer Picard iteration. Based on results from several diffusion and transport benchmark models, it was found that the Krylov–Schur method applied to the λ-eigenvalue problem reduces Picard solver times (excluding response generation) by a factor of 2–5. Furthermore, alternative methods, including Picard acceleration schemes, Steffensen’s method, and Newton’s method, are developed in this paper. These approaches often yield faster k-convergence and a need for fewer k-dependent response function evaluations, which is important because response generation is often the primary cost for problems using responses computed online (i.e., not from a precomputed database). Accelerated Picard iteration was found to reduce total computational times by 2–3 compared to the unaccelerated case for problems dominated by response generation. In addition, Newton’s method was found to provide nearly the same performance with improved robustness

A Technique: Exposure Therapy

Directory of Open Access Journals (Sweden)

Serkan AKKOYUNLU

2013-08-01

Conclusion: Exposure with response prevention is a basic and effective technique. Every cognitive behavior therapist must be able to implement this technique and be cognizant of pearls of this procedure. (Journal of Cognitive Behavioral Psychotherapy and Research 2013, 2: 121-128 [JCBPR 2013; 2(2.000: 121-128

MCNP perturbation technique for criticality analysis

International Nuclear Information System (INIS)

McKinney, G.W.; Iverson, J.L.

1995-01-01

The differential operator perturbation technique has been incorporated into the Monte Carlo N-Particle transport code MCNP and will become a standard feature of future releases. This feature includes first and/or second order terms of the Taylor Series expansion for response perturbations related to cross-section data (i.e., density, composition, etc.). Criticality analyses can benefit from this technique in that predicted changes in the track-length tally estimator of K eff may be obtained for multiple perturbations in a single run. A key advantage of this method is that a precise estimate of a small change in response (i.e., < 1%) is easily obtained. This technique can also offer acceptable accuracy, to within a few percent, for up to 20-30% changes in a response

Relaxation techniques for stress

Science.gov (United States)

... raise your heart rate. This is called the stress response. Relaxation techniques can help your body relax and lower your blood pressure ... also many other types of breathing techniques you can learn. In many cases, you do not need much ... including those that cause stress. Meditation has been practiced for thousands of years, ...

Controlling for Response Bias in Self-Ratings of Personality: A Comparison of Impression Management Scales and the Overclaiming Technique.

Science.gov (United States)

Müller, Sascha; Moshagen, Morten

2018-04-12

Self-serving response distortions pose a threat to the validity of personality scales. A common approach to deal with this issue is to rely on impression management (IM) scales. More recently, the overclaiming technique (OCT) has been proposed as an alternative and arguably superior measure of such biases. In this study (N = 162), we tested these approaches in the context of self- and other-ratings using the HEXACO personality inventory. To the extent that the OCT and IM scales can be considered valid measures of response distortions, they are expected to account for inflated self-ratings in particular for those personality dimensions that are prone to socially desirable responding. However, the results show that neither the OCT nor IM account for overly favorable self-ratings. The validity of IM as a measure of response biases was further scrutinized by a substantial correlation with other-rated honesty-humility. As such, this study questions the use of both the OCT and IM to assess self-serving response distortions.

A review on creatinine measurement techniques.

Science.gov (United States)

Mohabbati-Kalejahi, Elham; Azimirad, Vahid; Bahrami, Manouchehr; Ganbari, Ahmad

2012-08-15

This paper reviews the entire recent global tendency for creatinine measurement. Creatinine biosensors involve complex relationships between biology and micro-mechatronics to which the blood is subjected. Comparison between new and old methods shows that new techniques (e.g. Molecular Imprinted Polymers based algorithms) are better than old methods (e.g. Elisa) in terms of stability and linear range. All methods and their details for serum, plasma, urine and blood samples are surveyed. They are categorized into five main algorithms: optical, electrochemical, impedometrical, Ion Selective Field-Effect Transistor (ISFET) based technique and chromatography. Response time, detection limit, linear range and selectivity of reported sensors are discussed. Potentiometric measurement technique has the lowest response time of 4-10 s and the lowest detection limit of 0.28 nmol L(-1) belongs to chromatographic technique. Comparison between various techniques of measurements indicates that the best selectivity belongs to MIP based and chromatographic techniques. Copyright © 2012 Elsevier B.V. All rights reserved.

Adaptive Response Surface Techniques in Reliability Estimation

DEFF Research Database (Denmark)

Enevoldsen, I.; Faber, M. H.; Sørensen, John Dalsgaard

1993-01-01

Problems in connection with estimation of the reliability of a component modelled by a limit state function including noise or first order discontinuitics are considered. A gradient free adaptive response surface algorithm is developed. The algorithm applies second order polynomial surfaces...

Compensation of spatial system response in SPECT with conjugate gradient reconstruction technique

International Nuclear Information System (INIS)

Formiconi, A.R.; Pupi, A.; Passeri, A.

1989-01-01

A procedure for determination of the system matrix in single photon emission tomography (SPECT) is described which use a conjugate gradient reconstruction technique to take into account the variable system resolution of a camera equipped with parallel-hole collimators. The procedure involves acquisition of system line spread functions (LSF) in the region occupied by the object studied. Those data are used to generate a set of weighting factors based on the assumption that the LSFs of the collimated camera are of Gaussian shape with full width at half maximum (FWHM) linearly dependent on source depth in the span of image space. Factors are stored on a disc file for subsequent use in reconstruction. Afterwards reconstruction is performed using the conjugate gradient method with the system matrix modified by incorporation of these precalculated factors to take into account variable geometrical system response. The set of weighting factors is regenerated whenever acquisition conditions are changed (collimator, radius of rotation) with an ultra high resolution (UHR) collimator 2000 weighting factors need to be calculated. (author)

Manual of program operation for data analysis from radiometer system

International Nuclear Information System (INIS)

Silva Mello, L.A.R. da; Migliora, C.G.S.

1987-12-01

This manual describes how to use the software to retrieve and analyse data from radiometer systems and raingauges used in the 12 GHz PROPAGATION MEASUREMENTS/CANADA - TELEBRAS COOPERATION PROGRAM. The data retrieval and analisys is being carried out by CETUC, as part of the activities of the project Simulacao de Enlaces Satelite (SES). The software for these tasks has been supplied by the Canadian Research Centre (CRC), together with the measurement equipment. The two following sections describe the use of the data retrieval routines and the data analysis routines of program ATTEN. Also, a quick reference guide for commands that can be used when a microcomputer is local or remotely connected to a radiometer indoor unit is included as a last section. A more detailed description of these commands, their objectives and cautions that should de taken when using them can be found in the manual ''12 GHz Propagation Measurements System - Volume 1 - Dual Slope Radiometer and Data Aquisition System'', supplied by Diversitel Communications Inc. (author) [pt

SIMODIS - a software package for simulating nuclear reactor components

International Nuclear Information System (INIS)

Guimaraes, Lamartine; Borges, Eduardo M.

2000-01-01

In this paper it is presented the initial development effort in building a nuclear reactor component simulation package. This package was developed to be used in the MATLAB simulation environment. It uses the graphical capabilities from MATLAB and the advantages of compiled languages, as for instance FORTRAN and C ++ . From the MATLAB it takes the facilities for better displaying the calculated results. From the compiled languages it takes processing speed. So far models from reactor core, UTSG and OTSG have been developed. Also, a series a user-friendly graphical interfaces have been developed for the above models. As a by product a set of water and sodium thermal and physical properties have been developed and may be used directly as a function from MATLAB, or by being called from a model, as part of its calculation process. The whole set was named SIMODIS, which stands for SIstema MODular Integrado de Simulacao. (author)

Shallow Depth Geophysical Investigation Through the Application of Magnetic and Electric Resistance Techniques: AN Evaluation Study of the Responses of Magnetic and Electric Resistance Techniques to Archaeogeophysical Prospection Surveys in Greece and Cyprus

Science.gov (United States)

Sarris, Apostolos

The response characteristics of total intensity and vertical gradient magnetic techniques have been investigated in detail and compared with electric resistivity and other geophysical techniques. Four case studies from archaeological sites of Greece and Cyprus have been used as the experimental basis of this research project. Data from shallow depth geophysical investigations in these sites were collected over a period of four years. Interpretation of the geophysical results was based on the integration of the various prospecting methods. The results of the comparative study between the different techniques showed a strong correlation among all methods allowing the detection of certain features and the determination of their dimensions. The application of a large range of geophysical prospecting techniques in the surveyed archaeological sites has been able to detect the approximate position of the subsurface remains and to compare the different techniques in terms of the information that they reveal. Each one of these techniques has been used to examine the characteristic response of each method to the geophysical anomalies associated with the surveyed sites. Magnetic susceptibility measurements at two frequencies have identified areas and levels of intense human activity. A number of processing techniques such as low, high and band pass filtering in the spatial and frequency domain, computation of the residuals and fast Fourier transformation (FFT) of the magnetic potential data have been applied to the geophysical measurements. The subsequent convolution with filters representing apparent susceptibility, reduction to pole and equator, Gaussian and Butterworth regional and residual distributions, and inverse filtering in terms of spiking deconvolution have revealed a wealth of information necessary to obtain a more accurate picture of the concealed features. Inverse modelling of isolated magnetic anomalies has further enriched the information database of the

Randomized Item Response Theory Models

NARCIS (Netherlands)

Fox, Gerardus J.A.

2005-01-01

The randomized response (RR) technique is often used to obtain answers on sensitive questions. A new method is developed to measure latent variables using the RR technique because direct questioning leads to biased results. Within the RR technique is the probability of the true response modeled by

Semi-empirical simulation of thermoluminescent response under different filter geometries; Simulacao semi-empirica da resposta termoluminescente sob diferentes geometrias de filtro

Energy Technology Data Exchange (ETDEWEB)

Shammas, Gabriel Issa Jabra

2006-07-01

Many thermoluminescent materials has been developed and used for photon personal dosimetry but no one has all desired characteristics alone. These characteristics include robustness, high sensitivity, energy photon independence, large range of photon energy detection, good reproducibility, small fading and simple glow curve with peaks above 150 deg C. Calcium Sulfate Dysprosium doped (CaSO{sub 4}:Dy) phosphor Thermoluminescent Dosimeter (TLD) has been used by many laboratories, mainly in Brazil and India. Another interesting phosphor is Calcium Fluoride (CaF{sub 2}). These phosphor advantages begin to be more required and its disadvantages have became more apparent, in a global market more and more competitive. These phosphors are used in environmental and area monitoring, once they present more sensibility than other phosphors, like LiF:Mg. Theirs mainly disadvantage is a strong energetic dependence response, which must be corrected for theirs application in the field, where photon radiation is unknown a priori. An interesting way do make this correction in orthogonal incidence of the radiation on the phosphor is to interject a plane leaked filter between the beam and the phosphor. In order to reduce the energetic dependence on any incidence angle, reducing the field dose measurement uncertainty too, this work presents a simulation study on spherical filter geometries. It was simulated photon irradiations with Gamma rays of {sup 60}Co and x-rays of 33; 48 and 118 keV, on many incidence angles from zero to ninety degrees. These semi-empirical computational simulations using finite differences in three dimensions were done in spherical coordinates. The results pointed out the best filter thicknesses and widths, in order to optimize the correction on energetic dependence. (author)

A True Open-Loop Synchronization Technique

DEFF Research Database (Denmark)

Golestan, Saeed; Vidal, Ana; Yepes, Alejandro G.

2016-01-01

Synchronization techniques can be broadly classified into two major categories: Closed-loop and open-loop methods. The open-loop synchronization (OLS) techniques, contrary to the closed-loop ones, are unconditionally stable and benefit from a fast dynamic response. Their performance, however, tends...... is to develop a true OLS (and therefore, unconditionally stable) technique without any need for the calculation of sine and cosine functions. The effectiveness of the proposed synchronization technique is confirmed through the simulation and experimental results....

A novel field transplantation technique reveals intra-specific metal-induced oxidative responses in strains of Ectocarpus siliculosus with different pollution histories

International Nuclear Information System (INIS)

Sáez, Claudio A.; González, Alberto; Contreras, Rodrigo A.; Moody, A. John; Moenne, Alejandra; Brown, Murray T.

2015-01-01

A novel field transplantation technique, in which seaweed material is incorporated into dialysis tubing, was used to investigate intra-specific responses to metals in the model brown alga Ectocarpus siliculosus. Metal accumulation in the two strains was similar, with higher concentrations in material deployed to the metal-contaminated site (Ventanas, Chile) than the pristine site (Quintay, Chile). However, the oxidative responses differed. At Ventanas, strain Es147 (from low-polluted site) underwent oxidative damage whereas Es524 (from highly polluted site) was not affected. Concentrations of reduced ascorbate (ASC) and reduced glutathione (GSH) were significantly higher in Es524. Activities of the antioxidant enzymes superoxide dismutase (SOD), ascorbate peroxidase (APX), catalase (CAT), and glutathione reductase (GR) all increased in Es524, whereas only SOD increased in Es147. For the first time, employing a field transplantation technique, we provide unambiguous evidence of inter-population variation of metal-tolerance in brown algae and establish that antioxidant defences are, in part, responsible. - Highlights: • Metal tolerance in Ectocarpus siliculosus populations was studied through in situ experiments. • Metal tolerance in E. siliculosus populations is partly based in antioxidant defences. • In situ experiments using a dialysis tubing device was successful for metal diagnosis. - Field transplantation experimentation provides evidence that differential antioxidant defences, in part, mediate inter-population tolerance to metal pollution in the model brown alga Ectocarpus siliculosus

Republic of Georgia estimates for prevalence of drug use: Randomized response techniques suggest under-estimation.

Science.gov (United States)

Kirtadze, Irma; Otiashvili, David; Tabatadze, Mzia; Vardanashvili, Irina; Sturua, Lela; Zabransky, Tomas; Anthony, James C

2018-06-01

Validity of responses in surveys is an important research concern, especially in emerging market economies where surveys in the general population are a novelty, and the level of social control is traditionally higher. The Randomized Response Technique (RRT) can be used as a check on response validity when the study aim is to estimate population prevalence of drug experiences and other socially sensitive and/or illegal behaviors. To apply RRT and to study potential under-reporting of drug use in a nation-scale, population-based general population survey of alcohol and other drug use. For this first-ever household survey on addictive substances for the Country of Georgia, we used the multi-stage probability sampling of 18-to-64-year-old household residents of 111 urban and 49 rural areas. During the interviewer-administered assessments, RRT involved pairing of sensitive and non-sensitive questions about drug experiences. Based upon the standard household self-report survey estimate, an estimated 17.3% [95% confidence interval, CI: 15.5%, 19.1%] of Georgian household residents have tried cannabis. The corresponding RRT estimate was 29.9% [95% CI: 24.9%, 34.9%]. The RRT estimates for other drugs such as heroin also were larger than the standard self-report estimates. We remain unsure about what is the "true" value for prevalence of using illegal psychotropic drugs in the Republic of Georgia study population. Our RRT results suggest that standard non-RRT approaches might produce 'under-estimates' or at best, highly conservative, lower-end estimates. Copyright © 2018 Elsevier B.V. All rights reserved.

Neutron flux measurement utilizing Campbell technique

International Nuclear Information System (INIS)

Kropik, M.

2000-01-01

Application of the Campbell technique for the neutron flux measurement is described in the contribution. This technique utilizes the AC component (noise) of a neutron chamber signal rather than a usually used DC component. The Campbell theorem, originally discovered to describe noise behaviour of valves, explains that the root mean square of the AC component of the chamber signal is proportional to the neutron flux (reactor power). The quadratic dependence of the reactor power on the root mean square value usually permits to accomplish the whole current power range of the neutron flux measurement by only one channel. Further advantage of the Campbell technique is that large pulses of the response to neutrons are favoured over small pulses of the response to gamma rays in the ratio of their mean square charge transfer and thus, the Campbell technique provides an excellent gamma rays discrimination in the current operational range of a neutron chamber. The neutron flux measurement channel using state of the art components was designed and put into operation. Its linearity, accuracy, dynamic range, time response and gamma discrimination were tested on the VR-1 nuclear reactor in Prague, and behaviour under high neutron flux (accident conditions) was tested on the TRIGA nuclear reactor in Vienna. (author)

Analysing data from observer studies in medical imaging research: An introductory guide to free-response techniques

International Nuclear Information System (INIS)

Thompson, J.D.; Manning, D.J.; Hogg, P.

2014-01-01

Observer performance methods maintain their place in radiology research, particularly in the assessment of the diagnostic accuracy of new and existing techniques, despite not being fully embraced by the wider audience in medical imaging. The receiver operating characteristic (ROC) paradigm has been widely used in research and the latest location sensitive methods allow an analysis that is closer to the clinical scenario. This paper discusses the underpinning theories behind observer performance assessment, exploring the potential sources of error and the development of the ROC method. The paper progresses by explaining the clinical relevance and statistical suitability of the free-response ROC (FROC) paradigm, and the methodological considerations for those wishing to perform an observer performance study

Modeling and optimization of effective parameters on the size of synthesized Fe{sub 3}O{sub 4} superparamagnetic nanoparticles by coprecipitation technique using response surface methodology

Energy Technology Data Exchange (ETDEWEB)

Ghazanfari, Mohammad Reza, E-mail: Ghazanfari.mr@gmail.com [Department of Materials Science and Engineering, Ferdowsi University of Mashhad, 9177948974 Mashhad (Iran, Islamic Republic of); Kashefi, Mehrdad, E-mail: m-kashefi@um.ac.ir [Department of Materials Science and Engineering, Ferdowsi University of Mashhad, 9177948974 Mashhad (Iran, Islamic Republic of); Jaafari, Mahmoud Reza [Biotechnology Research Center, Nanotechnology Research Center, School of Pharmacy, Mashhad University of Medical Sciences, Mashhad (Iran, Islamic Republic of)

2016-05-01

Generally, the statistical methods are defined as appropriate techniques to study the processes trends. In current research, the Fe{sub 3}O{sub 4} superparamagnetic nanoparticles were synthesized by coprecipitation method. In order to investigate the size properties of synthesized particles, the experimental design was done using central composite method (CCD) of response surface methodology (RSM) while the temperature, pH, and cation ratio of reaction were selected as influential factors. After particles synthesis based on designed runs, the different responses such as hydrodynamic size of particles (both freeze dried and air dried), size distribution, crystallite size, magnetic size, and zeta potential were evaluated by different techniques i.e. dynamic light scattering (DLS), X-ray diffraction (XRD), and vibrating sample magnetometer (VSM). Based on these results, the quadratic polynomial model was fitted for each response that could predict the response amounts. In following, the study of factors effects was carried out that showed the temperature, pH, and their interactions had higher effectiveness. Finally, by optimizing, it was clear that the minimum amounts of particle size (10.15 nm) and size distribution (13.01 nm) were reached in the minimum temperature (70 °C) and cation ratio (0.5) amounts and maximum pH amount (10.5). Moreover, the characterizations showed the particles size was about 10 nm while the amounts of M{sub s}, H{sub c}, and M{sub r} were equal to 60 (emu/g), 0.2 (Oe) and 0.22 (emu/g), respectively. - Highlights: • The Fe{sub 3}O{sub 4} nanoparticles were successfully synthesized by coprecipitation method. • By RSM technique, some predicted models were presented for particles size. • Temperature, pH and their interactions had most effectiveness on the particles size. • The drying techniques can effect on the size properties.

Techniques for Maximizing the Performance of Molecular Pathology Testing: Responsibilities of All Pathologists

Directory of Open Access Journals (Sweden)

Evren UZUN

2018-05-01

Full Text Available Molecular pathological analysis has an expanding role in patient diagnosis and management. The performance of these techniques relies on excellent laboratory procedures. However, the crucial step is obtaining the best samples for molecular analysis. Archiving and selection of these are the responsibilities of all pathologists even if they are not working at a center with molecular pathological facilities. This review focuses on the features of different types of materials for molecular pathological analysis. Many steps that might affect the results, including communication between the pathologist and the oncology team, features of different types of materials (cytological, tissue blocks, biopsy, circulating tumor cells (CTCs and cell-free circulating nucleic acids, effects of tissue processing, methods for selecting the best material, and tissue saving and tumor enrichment methods are discussed. The procedures for referral to a center for molecular pathological analysis are also mentioned. Awareness of the importance of the cytopathological and histopathological material of the patients for future molecular pathological analysis by pathologists is of the utmost importance.

Development of criteria for evaluating clinical response in thyroid eye disease (CRI-TED) using a modified Delphi technique

Science.gov (United States)

Douglas, Raymond S.; Tsirbas, Angelo; Gordon, Mark; Lee, Diana; Khadavi, Nicole; Garneau, Helene Chokron; Goldberg, Robert A.; Cahill, Kenneth; Dolman, Peter J.; Elner, Victor; Feldon, Steve; Lucarelli, Mark; Uddin, Jimmy; Kazim, Michael; Smith, Terry J.; Khanna, Dinesh

2014-01-01

To identify components of a provisional clinical response index for thyroid eye disease (CRI-TED) using a modified Delphi technique. The International Thyroid Eye Disease Society (ITEDS) conducted a structured, 3-round Delphi exercise establishing consensus for a core set of measures for clinical trials in TED. The steering committee discussed the results in a face-to-face meeting (nominal group technique) and evaluated each criterion with respect to its feasibility, reliability, redundancy, and validity. Redundant measures were consolidated or excluded. Criteria were parsed into 11 domains for the Delphi surveys. Eighty four respondents participated in the Delphi-1 survey, providing 220 unique items. Ninety- two members (100% of the respondents from Delphi 1 plus eight new participants) responded in Delphi-2 and rated the same 220 items. Sixty-four members (76% of participants) rated 153 criteria in Delphi-3 (67 criteria were excluded due to redundancy). Criteria with a mean greater than 6 (1 least appropriate to 9 most appropriate) were further evaluated by the nominal group technique and provisional core measures were chosen. Using a Delphi exercise, we developed provisional core measures for assessing disease activity and severity in clinical trials of therapies for TED. These measures will be iteratively refined for use in multicenter clinical trials. PMID:19752424

Sharing a Reading Technique with Families

Science.gov (United States)

Irish, Christy K.; Parsons, Seth A.

2016-01-01

Sharing reading techniques with families is an important responsibility of teachers. Dialogic reading is one way to improve young students' expressive vocabulary skills, which are important for later reading success. Dialogic reading also supports students' understanding of story structure and content. This well researched technique has not been…

Mean-Variance-Validation Technique for Sequential Kriging Metamodels

International Nuclear Information System (INIS)

Lee, Tae Hee; Kim, Ho Sung

2010-01-01

The rigorous validation of the accuracy of metamodels is an important topic in research on metamodel techniques. Although a leave-k-out cross-validation technique involves a considerably high computational cost, it cannot be used to measure the fidelity of metamodels. Recently, the mean 0 validation technique has been proposed to quantitatively determine the accuracy of metamodels. However, the use of mean 0 validation criterion may lead to premature termination of a sampling process even if the kriging model is inaccurate. In this study, we propose a new validation technique based on the mean and variance of the response evaluated when sequential sampling method, such as maximum entropy sampling, is used. The proposed validation technique is more efficient and accurate than the leave-k-out cross-validation technique, because instead of performing numerical integration, the kriging model is explicitly integrated to accurately evaluate the mean and variance of the response evaluated. The error in the proposed validation technique resembles a root mean squared error, thus it can be used to determine a stop criterion for sequential sampling of metamodels

Diagnostic accuracy of magnetic resonance imaging techniques for treatment response evaluation in patients with high-grade glioma, a systematic review and meta-analysis

Energy Technology Data Exchange (ETDEWEB)

Dijken, Bart R.J. van [University of Groningen, University Medical Center Groningen Department of Radiology, Groningen (Netherlands); Laar, Peter Jan van; Hoorn, Anouk van der [University of Groningen, University Medical Center Groningen Department of Radiology, Groningen (Netherlands); University of Groningen, University Medical Center Groningen, Center for Medical Imaging-North East Netherlands, Groningen (Netherlands); Holtman, Gea A. [University of Groningen, University Medical Center Groningen, Department of General Practice, Groningen (Netherlands)

2017-10-15

Treatment response assessment in high-grade gliomas uses contrast enhanced T1-weighted MRI, but is unreliable. Novel advanced MRI techniques have been studied, but the accuracy is not well known. Therefore, we performed a systematic meta-analysis to assess the diagnostic accuracy of anatomical and advanced MRI for treatment response in high-grade gliomas. Databases were searched systematically. Study selection and data extraction were done by two authors independently. Meta-analysis was performed using a bivariate random effects model when ≥5 studies were included. Anatomical MRI (five studies, 166 patients) showed a pooled sensitivity and specificity of 68% (95%CI 51-81) and 77% (45-93), respectively. Pooled apparent diffusion coefficients (seven studies, 204 patients) demonstrated a sensitivity of 71% (60-80) and specificity of 87% (77-93). DSC-perfusion (18 studies, 708 patients) sensitivity was 87% (82-91) with a specificity of 86% (77-91). DCE-perfusion (five studies, 207 patients) sensitivity was 92% (73-98) and specificity was 85% (76-92). The sensitivity of spectroscopy (nine studies, 203 patients) was 91% (79-97) and specificity was 95% (65-99). Advanced techniques showed higher diagnostic accuracy than anatomical MRI, the highest for spectroscopy, supporting the use in treatment response assessment in high-grade gliomas. (orig.)

Optimization of Coolant Technique Conditions for Machining A319 Aluminium Alloy Using Response Surface Method (RSM)

Science.gov (United States)

Zainal Ariffin, S.; Razlan, A.; Ali, M. Mohd; Efendee, A. M.; Rahman, M. M.

2018-03-01

Background/Objectives: The paper discusses about the optimum cutting parameters with coolant techniques condition (1.0 mm nozzle orifice, wet and dry) to optimize surface roughness, temperature and tool wear in the machining process based on the selected setting parameters. The selected cutting parameters for this study were the cutting speed, feed rate, depth of cut and coolant techniques condition. Methods/Statistical Analysis Experiments were conducted and investigated based on Design of Experiment (DOE) with Response Surface Method. The research of the aggressive machining process on aluminum alloy (A319) for automotive applications is an effort to understand the machining concept, which widely used in a variety of manufacturing industries especially in the automotive industry. Findings: The results show that the dominant failure mode is the surface roughness, temperature and tool wear when using 1.0 mm nozzle orifice, increases during machining and also can be alternative minimize built up edge of the A319. The exploration for surface roughness, productivity and the optimization of cutting speed in the technical and commercial aspects of the manufacturing processes of A319 are discussed in automotive components industries for further work Applications/Improvements: The research result also beneficial in minimizing the costs incurred and improving productivity of manufacturing firms. According to the mathematical model and equations, generated by CCD based RSM, experiments were performed and cutting coolant condition technique using size nozzle can reduces tool wear, surface roughness and temperature was obtained. Results have been analyzed and optimization has been carried out for selecting cutting parameters, shows that the effectiveness and efficiency of the system can be identified and helps to solve potential problems.

The Delphi Technique in Educational Research

Directory of Open Access Journals (Sweden)

Ravonne A. Green

2014-04-01

Full Text Available The Delphi Technique has been useful in educational settings in forming guidelines, standards, and in predicting trends. Judd lists these major uses of the Delphi Technique in higher education: (a cost-effectiveness, (b cost–benefit analysis, (c curriculum and campus planning, and (d university-wide educational goals and objectives. The thorough Delphi researcher seeks to reconcile the Delphi consensus with current literature, institutional research, and the campus environment. This triangle forms a sound base for responsible research practice. This book gives an overview of the Delphi Technique and the primary uses of this technique in research. This article on the Delphi Technique will give the researcher an invaluable resource for learning about the Delphi Technique and for applying this method in educational research projects.

Invasive and noninvasive dental analgesia techniques.

Science.gov (United States)

Estafan, D J

1998-01-01

Although needle-administered local anesthesia has been an essential tool of modern dentistry, it has also been responsible for many patients' fears of dental visits. Several new techniques have recently evolved that may offer viable alternatives. Two of these operate via electronic mechanisms that interfere with pain signals, two others involve transmucosal modes of administration, and a fifth technique involves an intraosseous pathway for anesthesia administration. Each of these techniques has different indications for dental procedures, but none is intended to replace needle administration in dentistry. This overview highlights the salient features of these alternative dental anesthesia techniques.

Physical simulations using centrifuge techniques

International Nuclear Information System (INIS)

Sutherland, H.J.

1981-01-01

Centrifuge techniques offer a technique for doing physical simulations of the long-term mechanical response of deep ocean sediment to the emplacement of waste canisters and to the temperature gradients generated by them. Preliminary investigations of the scaling laws for pertinent phenomena indicate that the time scaling will be consistent among them and equal to the scaling factor squared. This result implies that this technique will permit accelerated-life-testing of proposed configurations; i.e, long-term studies may be done in relatively short times. Presently, existing centrifuges are being modified to permit scale model testing. This testing will start next year

Accuracy of different temperature reading techniques and associated stress response in hospitalized dogs.

Science.gov (United States)

Gomart, Samantha B; Allerton, Fergus J W; Gommeren, Kris

2014-01-01

To evaluate the accuracy and associated induced stress response of axillary, auricular, and rectal thermometry in hospitalized dogs. Prospective observational study from October 2011 to February 2012. University veterinary teaching hospital. Two hundred fifty hospitalized dogs. All hospitalized dogs were considered eligible unless their condition precluded measurement at one of the designated sites. A veterinary auricular infrared device for auricular temperature (OT) and an electronic predictive thermometer for rectal temperature (RT) and axillary temperature (AT) were used for temperature measurements. All recordings were obtained by the same investigator in a randomized fashion. Heart rate was noted before and immediately after each measurement. Stress behaviors (eg, vocalization, lip licking, shaking, panting, defensive behavior) were also recorded and graded from 0 (lowest) to 4 (highest). Signalment, analgesic therapy, and length of hospitalization were recorded. RT measurements were associated with greatest increase in heart rate (P 0.05). AT and to a lesser extent OT are reliable, less stressful alternatives to estimate RT in dogs. Further studies are needed to evaluate these techniques in hyperthermic dogs, and to evaluate the use of AT and OT as monitoring tools in intensive care patients. © Veterinary Emergency and Critical Care Society 2014.

Emerging Techniques in Brain Tumor Imaging: What Radiologists Need to Know

Energy Technology Data Exchange (ETDEWEB)

Kim, Minjae; Kim, Ho Sung [Department of Radiology and Research Institute of Radiology, University of Ulsan College of Medicine, Asan Medical Center, Seoul 05505 (Korea, Republic of)

2016-11-01

Among the currently available brain tumor imaging, advanced MR imaging techniques, such as diffusion-weighted MR imaging and perfusion MR imaging, have been used for solving diagnostic challenges associated with conventional imaging and for monitoring the brain tumor treatment response. Further development of advanced MR imaging techniques and postprocessing methods may contribute to predicting the treatment response to a specific therapeutic regimen, particularly using multi-modality and multiparametric imaging. Over the next few years, new imaging techniques, such as amide proton transfer imaging, will be studied regarding their potential use in quantitative brain tumor imaging. In this review, the pathophysiologic considerations and clinical validations of these promising techniques are discussed in the context of brain tumor characterization and treatment response.

Spectral Estimation by the Random Dec Technique

DEFF Research Database (Denmark)

Brincker, Rune; Jensen, Jacob L.; Krenk, Steen

1990-01-01

This paper contains an empirical study of the accuracy of the Random Dec (RDD) technique. Realizations of the response from a single-degree-of-freedom system loaded by white noise are simulated using an ARMA model. The Autocorrelation function is estimated using the RDD technique and the estimated...

Spectral Estimation by the Random DEC Technique

DEFF Research Database (Denmark)

Brincker, Rune; Jensen, J. Laigaard; Krenk, S.

This paper contains an empirical study of the accuracy of the Random Dec (RDD) technique. Realizations of the response from a single-degree-of-freedom system loaded by white noise are simulated using an ARMA model. The Autocorrelation function is estimated using the RDD technique and the estimated...

Plasticity models of material variability based on uncertainty quantification techniques

Energy Technology Data Exchange (ETDEWEB)

Jones, Reese E. [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Rizzi, Francesco [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Boyce, Brad [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Templeton, Jeremy Alan [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Ostien, Jakob [Sandia National Lab. (SNL-CA), Livermore, CA (United States)

2017-11-01

The advent of fabrication techniques like additive manufacturing has focused attention on the considerable variability of material response due to defects and other micro-structural aspects. This variability motivates the development of an enhanced design methodology that incorporates inherent material variability to provide robust predictions of performance. In this work, we develop plasticity models capable of representing the distribution of mechanical responses observed in experiments using traditional plasticity models of the mean response and recently developed uncertainty quantification (UQ) techniques. Lastly, we demonstrate that the new method provides predictive realizations that are superior to more traditional ones, and how these UQ techniques can be used in model selection and assessing the quality of calibrated physical parameters.

A simple white noise analysis of neuronal light responses.

Science.gov (United States)

Chichilnisky, E J

2001-05-01

A white noise technique is presented for estimating the response properties of spiking visual system neurons. The technique is simple, robust, efficient and well suited to simultaneous recordings from multiple neurons. It provides a complete and easily interpretable model of light responses even for neurons that display a common form of response nonlinearity that precludes classical linear systems analysis. A theoretical justification of the technique is presented that relies only on elementary linear algebra and statistics. Implementation is described with examples. The technique and the underlying model of neural responses are validated using recordings from retinal ganglion cells, and in principle are applicable to other neurons. Advantages and disadvantages of the technique relative to classical approaches are discussed.

Estimation of Correlation Functions by the Random Decrement Technique

DEFF Research Database (Denmark)

Brincker, Rune; Krenk, Steen; Jensen, Jakob Laigaard

responses simulated by two SDOF ARMA models loaded by the same bandlimited white noise. The speed and the accuracy of the RDD technique is compared to the Fast Fourier Transform (FFT) technique. The RDD technique does not involve multiplications, but only additions. Therefore, the technique is very fast......The Random Decrement (RDD) Technique is a versatile technique for characterization of random signals in the time domain. In this paper a short review of the theoretical basis is given, and the technique is illustrated by estimating auto-correlation functions and cross-correlation functions on modal...

Estimation of Correlation Functions by the Random Decrement Technique

DEFF Research Database (Denmark)

Brincker, Rune; Krenk, Steen; Jensen, Jacob Laigaard

1991-01-01

responses simulated by two SDOF ARMA models loaded by the same band-limited white noise. The speed and the accuracy of the RDD technique is compared to the Fast Fourier Transform (FFT) technique. The RDD technique does not involve multiplications, but only additions. Therefore, the technique is very fast......The Random Decrement (RDD) Technique is a versatile technique for characterization of random signals in the time domain. In this paper a short review of the theoretical basis is given, and the technique is illustrated by estimating auto-correlation functions and cross-correlation functions on modal...

Estimation of Correlation Functions by the Random Decrement Technique

DEFF Research Database (Denmark)

Brincker, Rune; Krenk, Steen; Jensen, Jakob Laigaard

1992-01-01

responses simulated by two SDOF ARMA models loaded by the same bandlimited white noise. The speed and the accuracy of the RDD technique is compared to the Fast Fourier Transform (FFT) technique. The RDD technique does not involve multiplications, but only additions. Therefore, the technique is very fast......The Random Decrement (RDD) Technique is a versatile technique for characterization of random signals in the time domain. In this paper a short review of the theoretical basis is given, and the technique is illustrated by estimating auto-correlation functions and cross-correlation functions on modal...

Use of sting-response techniques for simulate diagnostics in human esophagus

International Nuclear Information System (INIS)

Rodriguez, I.; Gonzalez, Y.; Valdes, L.; Alfonso, J.A.; Estevez, E.

2003-01-01

In this work a study of simulation of the gamma graphic studies that are carried out in human esophagus in the Dept. of Nuclear Medicine of the 'Celestino Hernandez Robau Hospital of Santa Clara is presented. For the investigation tubular reactors were used and sting-response techniques with radioactive tracer of Technetium 99 metastable to a concentration of 1 mCi and several flows were applied. The distribution curves of residences times were obtained, those that respond to an equation of the type: Y = A + B exp (- exp((x-C)/D)) - ((x-C/D)+1). They were also carried out, optimizations studies of the doses of the radioactive to give to the patients from 1 mCi (that is the one used in studies) up to 0,5 mCi, and the influences on the obtained distributions of residence time were analyzed. It was confirmed the possibility to lower the doses with clear information of the signal. It was also carried out a simulation of the attenuation of the radiations that takes place in the patients by the interposition of tissues among the analyzed organ, and the detection equipment. It was used paraffin for tissue simulation. It was found the almost independence of the intensity of the radiations with the thickness, for the assayed doses. Lastly it was found a complex mathematical model that responds to the diagnostic curves obtained in these studies, being correlated the coefficients of the pattern with the most important physical parameters of the system, giving it a practical and useful value, all time that the error among the values that this it predicts and the experimental ones do not surpass of 5%. (Author)

Response spectrum analysis of coupled structural response to a three component seismic disturbance

International Nuclear Information System (INIS)

Boulet, J.A.M.; Carley, T.G.

1977-01-01

The work discussed herein is a comparison and evaluation of several response spectrum analysis (RSA) techniques as applied to the same structural model with seismic excitation having three spatial components. Lagrange's equations of motion for the system were written in matrix form and uncoupled with the modal matrix. Numerical integration (fourth order Runge-Kutta) of the resulting model equations produced time histories of system displacements in response to simultaneous application of three orthogonal components of ground motion, and displacement response spectra for each modal coordinate in response to each of the three ground motion components. Five different RSA techniques were used to combine the spectral displacements and the modal matrix to give approximations of maximum system displacements. These approximations were then compared with the maximum system displacements taken from the time histories. The RSA techniques used are the method of absolute sums, the square root of the sum of the squares, the double sum approach, the method of closely spaced modes, and Lin's method. The vectors of maximum system displacements as computed by the time history analysis and the five response spectrum analysis methods are presented. (Auth.)

The optimization of essential oils supercritical CO2 extraction from Lavandula hybrida through static-dynamic steps procedure and semi-continuous technique using response surface method

Science.gov (United States)

Kamali, Hossein; Aminimoghadamfarouj, Noushin; Golmakani, Ebrahim; Nematollahi, Alireza

2015-01-01

Aim: The aim of this study was to examine and evaluate crucial variables in essential oils extraction process from Lavandula hybrida through static-dynamic and semi-continuous techniques using response surface method. Materials and Methods: Essential oil components were extracted from Lavandula hybrida (Lavandin) flowers using supercritical carbon dioxide via static-dynamic steps (SDS) procedure, and semi-continuous (SC) technique. Results: Using response surface method the optimum extraction yield (4.768%) was obtained via SDS at 108.7 bar, 48.5°C, 120 min (static: 8×15), 24 min (dynamic: 8×3 min) in contrast to the 4.620% extraction yield for the SC at 111.6 bar, 49.2°C, 14 min (static), 121.1 min (dynamic). Conclusion: The results indicated that a substantial reduction (81.56%) solvent usage (kg CO2/g oil) is observed in the SDS method versus the conventional SC method. PMID:25598636

Evaluation of Damping Using Time Domain OMA Techniques

DEFF Research Database (Denmark)

Bajric, Anela; Brincker, Rune; Georgakis, Christos T.

2014-01-01

. In this paper a comparison is made of the effectiveness of three existing OMA techniques in providing accurate damping estimates for varying loadings, levels of noise, number of added measurement channels and structural damping. The evaluated techniques are derived in the time domain and are namely the Ibrahim...... Time Domain (ITD), Eigenvalue Realization Algorithm (ERA) and the Polyreference Time Domain (PTD). The response of a two degree-of-freedom (2DOF) system is numerically established from specified modal parameters with well separated and closely spaced modes. Two types of response are considered, free...

Survey on Chatbot Design Techniques in Speech Conversation Systems

OpenAIRE

Sameera A. Abdul-Kader; Dr. John Woods

2015-01-01

Human-Computer Speech is gaining momentum as a technique of computer interaction. There has been a recent upsurge in speech based search engines and assistants such as Siri, Google Chrome and Cortana. Natural Language Processing (NLP) techniques such as NLTK for Python can be applied to analyse speech, and intelligent responses can be found by designing an engine to provide appropriate human like responses. This type of programme is called a Chatbot, which is the focus of this study. This pap...

5 Things To Know About Relaxation Techniques for Stress

Science.gov (United States)

... Techniques for Stress Share: When you’re under stress, your body reacts by releasing hormones that produce the “fight- ... relaxation techniques could counteract the negative effects of stress. ... the body's natural relaxation response, characterized by slower breathing, lower ...

Projection operator techniques in nonequilibrium statistical mechanics

International Nuclear Information System (INIS)

Grabert, H.

1982-01-01

This book is an introduction to the application of the projection operator technique to the statistical mechanics of irreversible processes. After a general introduction to the projection operator technique and statistical thermodynamics the Fokker-Planck and the master equation approach are described together with the response theory. Then, as applications the damped harmonic oscillator, simple fluids, and the spin relaxation are considered. (HSI)

The finite element response matrix method

International Nuclear Information System (INIS)

Nakata, H.; Martin, W.R.

1983-02-01

A new technique is developed with an alternative formulation of the response matrix method implemented with the finite element scheme. Two types of response matrices are generated from the Galerkin solution to the weak form of the diffusion equation subject to an arbitrary current and source. The piecewise polynomials are defined in two levels, the first for the local (assembly) calculations and the second for the global (core) response matrix calculations. This finite element response matrix technique was tested in two 2-dimensional test problems, 2D-IAEA benchmark problem and Biblis benchmark problem, with satisfatory results. The computational time, whereas the current code is not extensively optimized, is of the same order of the well estabilished coarse mesh codes. Furthermore, the application of the finite element technique in an alternative formulation of response matrix method permits the method to easily incorporate additional capabilities such as treatment of spatially dependent cross-sections, arbitrary geometrical configurations, and high heterogeneous assemblies. (Author) [pt

The biological response of plucked human hair to low-dose radiation: a measure of individual radiosensitivity and a technique for biological dosimetry

International Nuclear Information System (INIS)

Swain, D.

1997-01-01

It is often assumed that the effects of radiation are linear with dose and that high dose effects can be extrapolated to low dose levels. However, there are a variety of mechanisms which can alter the response at low doses. The most important of these relate to induced sensitivity or induced repair mechanisms. It is therefore important that this area is studied in more depth by looking at the molecular effects and damage to cells at low doses. It is well known that there are certain rare genetic syndromes which predispose individuals to cancer, e.g. ataxia telangiectasia. It is also probable that there is a large range of sensitivity in the natural variation of individuals to the risk of radiation-induced cancer. It is proposed that radiosensitivity is studied using stimulated lymphocytes from whole blood and the technique extended to look at the effects in cell cultures established from human hair. Radiation treatment of cell cultures established from plucked human hair has been previously advocated as a non-invasive technique for non-uniform biological dosimetry and it is proposed that these techniques are adapted to the use of hair to estimate individual radiosensitivity. The aim is to establish and optimize these techniques for culturing keratinocytes from plucked human hair follicles with a view to study biological markers for the subsequent assessment of radiosensitivity. Preliminary results are promising and suggest that the technique for culturing keratinocytes from hair presents a feasible approach. Results from this primary cell culture technique and results from the comparison of the micronuclei data obtained from the cell cultures and stimulated lymphocytes will be presented. (author)

Passive Super-Low Frequency electromagnetic prospecting technique

Science.gov (United States)

Wang, Nan; Zhao, Shanshan; Hui, Jian; Qin, Qiming

2017-03-01

The Super-Low Frequency (SLF) electromagnetic prospecting technique, adopted as a non-imaging remote sensing tool for depth sounding, is systematically proposed for subsurface geological survey. In this paper, we propose and theoretically illustrate natural source magnetic amplitudes as SLF responses for the first step. In order to directly calculate multi-dimensional theoretical SLF responses, modeling algorithms were developed and evaluated using the finite difference method. The theoretical results of three-dimensional (3-D) models show that the average normalized SLF magnetic amplitude responses were numerically stable and appropriate for practical interpretation. To explore the depth resolution, three-layer models were configured. The modeling results prove that the SLF technique is more sensitive to conductive objective layers than high resistive ones, with the SLF responses of conductive objective layers obviously showing uprising amplitudes in the low frequency range. Afterwards, we proposed an improved Frequency-Depth transformation based on Bostick inversion to realize the depth sounding by empirically adjusting two parameters. The SLF technique has already been successfully applied in geothermal exploration and coalbed methane (CBM) reservoir interpretation, which demonstrates that the proposed methodology is effective in revealing low resistive distributions. Furthermore, it siginificantly contributes to reservoir identification with electromagnetic radiation anomaly extraction. Meanwhile, the SLF interpretation results are in accordance with dynamic production status of CBM reservoirs, which means it could provide an economical, convenient and promising method for exploring and monitoring subsurface geo-objects.

COGNITIVE RESTRUCTURING: ALTERNATIVE COUNSELING TECHNIQUES TO REDUCTION ACADEMIC PROCRASTINATION

Directory of Open Access Journals (Sweden)

Annisa Sofiana

2016-12-01

Full Text Available Procrastination is often experienced by almost everyone, including students who often delay to resolve any responsibility in the academic process that would decrease the individual academic achievement. cognitive restructuring is one of the cognitive techniques used in counseling in addition to cognitive behavioral techniques (behavioral and didaktif techniques. This technique has several procedures by focusing on identifying an effort and changing dysfunctional thoughts or negative self-statements into a new belief that is more rational and adaptive, which will affect more rational behavior anyway. Cognitive restructuring techniques assessed to be an alternative counseling techniques in reducing academic procrastination.

A Quantitative Technique for Beginning Microscopists.

Science.gov (United States)

Sundberg, Marshall D.

1984-01-01

Stereology is the study of three-dimensional objects through the interpretation of two-dimensional images. Stereological techniques used in introductory botany to quantitatively examine changes in leaf anatomy in response to different environments are discussed. (JN)

BREATHING EXERCISE RELAXATION INCREASE PHSYCOLOGICAL RESPONSE PRESCHOOL CHILDREN

Directory of Open Access Journals (Sweden)

Yuni Sufyanti Arief

2017-07-01

Full Text Available Introduction: Being hospitalize will be made the children become stress. Hospitalization response of the child particularly is afraid sense regard to painfull procedure and increase to attack the invasive procedure. The aimed of this study was to describe the influence of breathing exercise relaxation technique regarded to phsycological receiving responses in the preeliminary school chidren while they were receiving invasive procedure. Method: A quasy experimental purposive sampling design was used in this study. There were 20 respondents who met to the inclusion criteria. The independent variable was the breathing exercise relaxation technique and the dependent variable was phsycological receiving responses. Data for phsylogical response were collected by using observation form then analyzed by using Wilcoxon Signed Rank Test and Mann Whitney U Test with significance level α≤0.05. Result :  The result showed that breathing exercise relaxation technique had significance influence to phsycological response (p=0.000. Discussion: It,s can be concluded that breathing exercise relaxation technique has an effect to increase pshycological response in preeliminary school children who received invasive procedure.

Authentication techniques for smart cards

International Nuclear Information System (INIS)

Nelson, R.A.

1994-02-01

Smart card systems are most cost efficient when implemented as a distributed system, which is a system without central host interaction or a local database of card numbers for verifying transaction approval. A distributed system, as such, presents special card and user authentication problems. Fortunately, smart cards offer processing capabilities that provide solutions to authentication problems, provided the system is designed with proper data integrity measures. Smart card systems maintain data integrity through a security design that controls data sources and limits data changes. A good security design is usually a result of a system analysis that provides a thorough understanding of the application needs. Once designers understand the application, they may specify authentication techniques that mitigate the risk of system compromise or failure. Current authentication techniques include cryptography, passwords, challenge/response protocols, and biometrics. The security design includes these techniques to help prevent counterfeit cards, unauthorized use, or information compromise. This paper discusses card authentication and user identity techniques that enhance security for microprocessor card systems. It also describes the analysis process used for determining proper authentication techniques for a system

Appropriate electromagnetic techniques for imaging geothermal fracture zones

Energy Technology Data Exchange (ETDEWEB)

Groom, R; Walker, P [PetRos EiKon Incorporated, Ontario (Canada)

1996-05-01

Electromagnetic surface detection of fracture zones has often been approached by using the magnetotelluric method. This technique suffers greatly from the quantity and scale of the conductive inhomogeneities lying above the fracture zones. Additionally, it suffers from the inherent inability to focus the source on the target. There are no such source focusing capabilities in magnetotellurics. Accordingly, the quantity of magnetotelluric data required to resolve targets in such complex conditions can make the technique inefficient and insufficient from a cost perspective. When attempting to reveal a subsurface structure and image it, the basic physical responses at hand must be kept in mind, and the appropriate source must be utilized, which most effectively illuminates the target. A further advantage to controlled sources is that imaging techniques may be used to accentuate the response due to knowledge and control of the source.

Application of the PRBS/FFT technique to digital simulations

International Nuclear Information System (INIS)

Hinds, H.W.

1977-01-01

This paper describes a method for obtaining a small-signal frequency response from a digital dynamic simulation. It employs a modified form of the PRBS/FFT technique, whereby a system is perturbed by a pseudo-random binary sequence and its response is analyzed using a fast Fourier transform-based program. Two applications of the technique are described; one involves a set of two coupled, second-order, ordinary differential equations; the other is a set of non-linear partial differential equations describing the thermohydraulic behaviour of water boiling in a fuel channel. (author)

Verification of the Monte Carlo differential operator technique for MCNP trademark

International Nuclear Information System (INIS)

McKinney, G.W.; Iverson, J.L.

1996-02-01

The differential operator perturbation technique has been incorporated into the Monte Carlo N-Particle transport code MCNP and will become a standard feature of future releases. This feature includes first and second order terms of the Taylor series expansion for response perturbations related to cross-section data (i.e., density, composition, etc.). Perturbation and sensitivity analyses can benefit from this technique in that predicted changes in one or more tally responses may be obtained for multiple perturbations in a single run. The user interface is intuitive, yet flexible enough to allow for changes in a specific microscopic cross section over a specified energy range. With this technique, a precise estimate of a small change in response is easily obtained, even when the standard deviation of the unperturbed tally is greater than the change. Furthermore, results presented in this report demonstrate that first and second order terms can offer acceptable accuracy, to within a few percent, for up to 20-30% changes in a response

The determination of acoustic reflection coefficients by using cepstral techniques, II: Extensions of the technique and considerations of accuracy

Science.gov (United States)

Bolton, J. S.; Gold, E.

1986-10-01

In a companion paper the cepstral technique for the measurement of reflection coefficients was described. In particular the concepts of extraction noise and extraction delay were introduced. They are considered further here, and, in addition, a means of extending the cepstral technique to accommodate surfaces having lengthy impulse responses is described. The character of extraction noise, a cepstral component which interferes with reflection measurements, is largely determined by the spectrum of the signal radiated from the source loudspeaker. Here the origin and effects of extraction noise are discussed and it is shown that inverse filtering techniques may be used to reduce extraction noise without making impractical demands of the electrical test signal or the source loudspeaker. The extraction delay, a factor which is introduced when removing the reflector impulse response from the power cepstrum, has previously been estimated by a cross-correlation technique. Here the importance of estimating the extraction delay accurately is emphasized by showing the effect of small spurious delays on the calculation of the normal impedance of a reflecting surface. The effects are shown to accord with theory, and it was found that the real part of the estimated surface normal impedance is very nearly maximized when the spurious delay is eliminated; this has suggested a new way of determining the extraction delay itself. Finally, the basic cepstral technique is suited only to the measurement of surfaces whose impulse responses are shorter than τ, the delay between the arrival of the direct and specularly reflected components at the measurement position. Here it is shown that this restriction can be eliminated, by using a process known as cepstral inversion, when the direct cepstrum has a duration less than τ and cepstral aliasing is insignificant. It is also possible to use this technique to deconvolve a signal from an echo sequence in the time domain, an operation

Response spectrum analysis of coupled structural response to a three component seismic disturbance

International Nuclear Information System (INIS)

Boulet, J.A.M.; Carley, T.G.

1977-01-01

The work discussed herein is a comparison and evaluation of several response spectrum analysis (RSA) techniques as applied to the same structural model with seismic excitation having three spatial components. The structural model includes five lumped masses (floors) connected by four elastic members. The base is supported by three translational springs and two horizontal torsional springs. In general, the mass center and shear center of a building floor are distinct locations. Hence, inertia forces, which act at the mass center, induce twisting in the structure. Through this induced torsion, the lateral (x and y) displacements of the mass elements are coupled. The ground motion components used for this study are artificial earthquake records generated from recorded accelerograms by a spectrum modification technique. The accelerograms have response spectra which are compatible with U.S. NRC Regulatory Guide 1.60. Lagrange's equations of motion for the system were written in matrix form and uncoupled with the modal matrix. Numerical integration (fourth order Runge-Kutta) of the resulting modal equations produced time histories of system displacements in response to simultaneous application of three orthogonal components of ground motion, and displacement response spectra for each modal coordinate in response to each of the three ground motion components. Five different RSA techniques were used to combine the spectral displacements and the modal matrix to give approximations of maximum system displacements. These approximations were then compared with the maximum system displacements taken from the time histories. The RSA techniques used are the method of absolute sums, the square root of the sum of the sum of the squares, the double sum approach, the method of closely spaced modes, and Lin's method

A Technique: Exposure Therapy

Directory of Open Access Journals (Sweden)

Serkan AKKOYUNLU

2013-07-01

Full Text Available Introduction: Exposure with response prevention is an effective treatment for all anxiety disorders. According to the behavioral learning theories, fears which are conditioned via classical conditioning are reinforced by respondent conditioning. Avoidance and safety seeking behaviors prevent disconfirmation of anxious beliefs. In exposure client faces stimulates or cues that elicit fear or distress, by this avoidance is inhibited. Clients are also encouraged to resists performing safety seeking behaviors or rituals that they utilize to reduce fear or distress. Accomplishing these habituation or extinction is achieved. In addition to this clients learn that feared consequences does not realize or not harmful as they believed by experiencing. Emotional processing is believed to be the mechanism of change in exposure.Objective: The aim of this review is to provide a definition of exposure and its effectiveness briefly, and describe how to implement exposure, its steps and remarkable aspects using. Exposure therapies and treatments that involve exposure are proved to be effective in all anxiety disorders. Exposure therapy can be divided in three parts: Assessment and providing a treatment rationale, creating an exposure hierarchy and response prevention plan, implementing exposure sessions. Clients must also continue to perform exposure between sessions. Therapy transcripts are also provided to exemplify these parts. Conclusion: Exposure with response prevention is a basic and effective technique. Every cognitive behavior therapist must be able to implement this technique and be cognizant of pearls of this procedure.

Seismic site-response characterization of high-velocity sites using advanced geophysical techniques: application to the NAGRA-Net

Science.gov (United States)

Poggi, V.; Burjanek, J.; Michel, C.; Fäh, D.

2017-08-01

The Swiss Seismological Service (SED) has recently finalised the installation of ten new seismological broadband stations in northern Switzerland. The project was led in cooperation with the National Cooperative for the Disposal of Radioactive Waste (Nagra) and Swissnuclear to monitor micro seismicity at potential locations of nuclear-waste repositories. To further improve the quality and usability of the seismic recordings, an extensive characterization of the sites surrounding the installation area was performed following a standardised investigation protocol. State-of-the-art geophysical techniques have been used, including advanced active and passive seismic methods. The results of all analyses converged to the definition of a set of best-representative 1-D velocity profiles for each site, which are the input for the computation of engineering soil proxies (traveltime averaged velocity and quarter-wavelength parameters) and numerical amplification models. Computed site response is then validated through comparison with empirical site amplification, which is currently available for any station connected to the Swiss seismic networks. With the goal of a high-sensitivity network, most of the NAGRA stations have been installed on stiff-soil sites of rather high seismic velocity. Seismic characterization of such sites has always been considered challenging, due to lack of relevant velocity contrast and the large wavelengths required to investigate the frequency range of engineering interest. We describe how ambient vibration techniques can successfully be applied in these particular conditions, providing practical recommendations for best practice in seismic site characterization of high-velocity sites.

Transsphenoidal hypophysectomy in beagle dogs: evaluation of a microsurgical technique

Energy Technology Data Exchange (ETDEWEB)

Meij, B. P. [Utrecht University, Utrecht (Netherlands); Voorhout, G.; Ingh, T.S.G.A.M. van den; Hazewinkel, H. A.W.; Verlaat, J.W. van ' t

1997-07-15

Objective-Assessment of a microsurgical technique for transsphenoidalhypophysectomy in dogs. Study Design-Prospective study using physicalexamination, pituitary function testing, computed tomography (CT), and histological examination at autopsy. Animals or Sample Population-Eight laboratory beagle dogs. Methods-Pituitary function was assessed before and at 10 weeks after hypophysectomy by combined administration of four releasing hormones (anterior pituitary), administration of haloperidol (pars intermedia), and infusion of hypertonic saline (posterior pituitary). Results-CT imaging enabled accurate preoperative localization of the pituitary. Appropriate positioning and surgical technique facilitated exposure of the pituitary and its extraction without hemorrhage. Postoperative recovery was generally uncomplicated. None of the eight dogs had somatotropic. gonadotropic, lactotropic, melanotropic, or posterior pituitary responses to stimulation at 10 weeks after hypophysectomy. Four dogs (ACTH nonresponders) also had no corticotropicresponse and four (ACTH responders) bad small but significant responses in the combined anterior pituitary function test. Adrenocortical atrophy was more pronounced in the ACTH nonresponders than in the responders. No residual pituitary tissue was found along the ventral hypothalamic diencephalon but nests of pituitary cells were found embedded infibrous tissue in the sella turcica. Conclusions-The surgical technique proved to be safe and effective. Microscopic nests of pituitary cells in the sella turcica may be responsible for residual corticotropic response to hypophysiotropic stimulation after hypophysectomy. Clinical Relevance-The surgical technique may be used in the treatment of dogs with pituitary-dependent hyperadrenocorticism. The corticotropic response is the most sensitive criterion in assessing completeness of hypophysectomy in dogs. (C) Copyright 1997 by The American College of Veterinary Surgeons.

Transsphenoidal hypophysectomy in beagle dogs: evaluation of a microsurgical technique

International Nuclear Information System (INIS)

Meij, B.P.; Voorhout, G.; Ingh, T.S.G.A.M. van den; Hazewinkel, H.A.W.; Verlaat, J.W. van 't

1997-01-01

Objective-Assessment of a microsurgical technique for transsphenoidalhypophysectomy in dogs. Study Design-Prospective study using physicalexamination, pituitary function testing, computed tomography (CT), and histological examination at autopsy. Animals or Sample Population-Eight laboratory beagle dogs. Methods-Pituitary function was assessed before and at 10 weeks after hypophysectomy by combined administration of four releasing hormones (anterior pituitary), administration of haloperidol (pars intermedia), and infusion of hypertonic saline (posterior pituitary). Results-CT imaging enabled accurate preoperative localization of the pituitary. Appropriate positioning and surgical technique facilitated exposure of the pituitary and its extraction without hemorrhage. Postoperative recovery was generally uncomplicated. None of the eight dogs had somatotropic. gonadotropic, lactotropic, melanotropic, or posterior pituitary responses to stimulation at 10 weeks after hypophysectomy. Four dogs (ACTH nonresponders) also had no corticotropicresponse and four (ACTH responders) bad small but significant responses in the combined anterior pituitary function test. Adrenocortical atrophy was more pronounced in the ACTH nonresponders than in the responders. No residual pituitary tissue was found along the ventral hypothalamic diencephalon but nests of pituitary cells were found embedded infibrous tissue in the sella turcica. Conclusions-The surgical technique proved to be safe and effective. Microscopic nests of pituitary cells in the sella turcica may be responsible for residual corticotropic response to hypophysiotropic stimulation after hypophysectomy. Clinical Relevance-The surgical technique may be used in the treatment of dogs with pituitary-dependent hyperadrenocorticism. The corticotropic response is the most sensitive criterion in assessing completeness of hypophysectomy in dogs. (C) Copyright 1997 by The American College of Veterinary Surgeons

Three decision-making aids: brainstorming, nominal group, and Delphi technique.

Science.gov (United States)

McMurray, A R

1994-01-01

The methods of brainstorming, Nominal Group Technique, and the Delphi technique can be important resources for nursing staff development educators who wish to expand their decision-making skills. Staff development educators may find opportunities to use these methods for such tasks as developing courses, setting departmental goals, and forecasting trends for planning purposes. Brainstorming, Nominal Group Technique, and the Delphi technique provide a structured format that helps increase the quantity and quality of participant responses.

Discriminative capacity of bronchodilator response measured with three different lung function techniques in asthmatic and healthy children aged 2 to 5 years

DEFF Research Database (Denmark)

Nielsen, K G; Bisgaard, H

2001-01-01

as compared with placebo in healthy control subjects. Lung function improved to a significantly greater extent in asthmatic children than in control subjects as reflected by all methods. sRaw provided the best discriminative power of such a bronchodilator response, with a sensitivity of 66% and specificity......The primary aim of this study was to quantify and compare bronchodilator responsiveness in healthy and asthmatic children aged 2 to 5 yr. The secondary aim of the study was to compare discriminative capacity (i.e., sensitivity, specificity, and predictive values of the reversibility test......) as measured with the impulse oscillation technique were assessed before and 20 min after inhalation of terbutaline from a pressurized metered-dose inhaler via a metal spacer by 92 children (37 healthy controls and 55 asthmatic subjects). The study of healthy children followed a randomized, double...

ProteinAC: a frequency domain technique for analyzing protein dynamics

Science.gov (United States)

Bozkurt Varolgunes, Yasemin; Demir, Alper

2018-03-01

It is widely believed that the interactions of proteins with ligands and other proteins are determined by their dynamic characteristics as opposed to only static, time-invariant processes. We propose a novel computational technique, called ProteinAC (PAC), that can be used to analyze small scale functional protein motions as well as interactions with ligands directly in the frequency domain. PAC was inspired by a frequency domain analysis technique that is widely used in electronic circuit design, and can be applied to both coarse-grained and all-atom models. It can be considered as a generalization of previously proposed static perturbation-response methods, where the frequency of the perturbation becomes the key. We discuss the precise relationship of PAC to static perturbation-response schemes. We show that the frequency of the perturbation may be an important factor in protein dynamics. Perturbations at different frequencies may result in completely different response behavior while magnitude and direction are kept constant. Furthermore, we introduce several novel frequency dependent metrics that can be computed via PAC in order to characterize response behavior. We present results for the ferric binding protein that demonstrate the potential utility of the proposed techniques.

Damage identification in beams by a response surface based technique

Directory of Open Access Journals (Sweden)

Teidj S.

2014-01-01

Full Text Available In this work, identification of damage in uniform homogeneous metallic beams was considered through the propagation of non dispersive elastic torsional waves. The proposed damage detection procedure consisted of the following sequence. Giving a localized torque excitation, having the form of a short half-sine pulse, the first step was calculating the transient solution of the resulting torsional wave. This torque could be generated in practice by means of asymmetric laser irradiation of the beam surface. Then, a localized defect assumed to be characterized by an abrupt reduction of beam section area with a given height and extent was placed at a known location of the beam. Next, the response in terms of transverse section rotation rate was obtained for a point situated afterwards the defect, where the sensor was positioned. This last could utilize in practice the concept of laser vibrometry. A parametric study has been conducted after that by using a full factorial design of experiments table and numerical simulations based on a finite difference characteristic scheme. This has enabled the derivation of a response surface model that was shown to represent adequately the response of the system in terms of the following factors: defect extent and severity. The final step was performing the inverse problem solution in order to identify the defect characteristics by using measurement.

Nuclear techniques in industry

International Nuclear Information System (INIS)

Barnette, P.

The long term development and successful utilization of the Tongonan geothermal field for electric power generation is ultimately a function of the response of the reservoir to extensive exploitation. A field drawdown test of several years duration has been planned to test this response. A number of nuclear chemical techniques have been incorporated into this to assist in quantitatively tracing the subsurface movements of both reservoir and reinjected fluids; and to provide an early warning of changes in the physical and chemical properties of the reservoir fluids with respect to natural recharge. The programme will be implemented by Philippine Atomic Energy Commission (PAEC) under contract to Philippine National Oil Company - Energy Development Corporation (PNOC-EDC). (author)

Spectrometry techniques for radioactivity measurements

International Nuclear Information System (INIS)

Anilkumar, S.

2016-01-01

The energy of the radiation emission following the nuclear decay is unique and the characteristic of the radio nuclide which undergoes decay. Thus measurement of the energy of the radiation offers a method of identifying the radio nuclides. The prime requirement of the energy measurement is a suitable detector which shows response proportional to the energy of the radiation rather than the presence of the radiation. The response from such detectors are suitably processed and distributed with respect to the signal strength which is proportional to incident energy. This distribution is normally referred as energy spectrum and is recorded in the multichannel analyser. The measurement of energy and intensity of radiation from the spectrum is called radiation spectrometry. Thus the radiation spectrometry allows the identification and quantification of radioactive isotopes in variety of matrices. The radiation spectrometry has now become a popular radioanalytical technique in wide area of nuclear fuel cycle programs. The popular spectrometry techniques commonly used for the radioactivity measurement and analysis are Alpha spectrometry, Gamma ray spectrometry and Beta spectrometry

Manipulation of the metabolic response in clinical practice

DEFF Research Database (Denmark)

Kehlet, H

2000-01-01

morbidity. Effective afferent neural blockade with continuous epidural local anesthetic techniques inhibits a major part of the endocrine metabolic response, leading to improved protein economy but without important effects on inflammatory or immunologic responses. In contrast, pain treatment with other...... modalities such as nonsteroidal antiinflammatory drugs (NSAIDs) and opioids has only a small inhibitory effect on endocrine metabolic responses. Preoperative high-dose glucocorticoid therapy provides additional pain relief and improves pulmonary function, but it reduces the inflammatory response (acute......-phase proteins, cytokines, hyperthermia) and immune function. Minimally invasive surgery leaves the endocrine metabolic responses largely unaltered but reduces the inflammatory response and immune suppression. Thus several techniques are available to modify the stress responses in elective surgery patients...

FIR Filter Sharpening by Frequency Masking and Pipelining-Interleaving Technique

Directory of Open Access Journals (Sweden)

CIRIC, M. P.

2014-11-01

Full Text Available This paper focuses on the improvements of digital filters with a highly sharp transition zone on the Xilinx FPGA chips by combining a sharpening method based on the amplitude change function and frequency masking and PI (Pipelining-Interleaving techniques. A linear phase requires digital filter realizations with Finite Impulse Response (FIR filters. On the other hand, a drawback of FIR filters applications is a low computational efficiency, especially in applications such as filter sharpening techniques, because this technique uses processing the data by repeated passes through the same filter. Computational efficiency of FIR filters can be significantly improved by using some of the multirate techniques, and such a degree of computation savings cannot be achieved in multirate implementations of IIR (Infinite Impulse Response filters. This paper shows the realization of a filter sharpening method with FIR filters combined with frequency masking and PI (Pipelining-Interleaving technique in order to effectively realize the filter with improved characteristic. This realization at the same time keeps the good features of FIR filters such as the linear phase characteristic.

Use of the modal superposition technique for piping system blowdown analyses

International Nuclear Information System (INIS)

Ware, A.G.; Macek, R.W.

1983-01-01

A standard method of solving for the seismic response of piping systems is the modal superposition technique. Only a limited number of structural modes are considered (typically those up to 33 Hz in the U.S.), since the effect on the calculated response due to higher modes is generally small, and the method can result in considerable computer cost savings over the direct integration method. The modal superposition technique has also been applied to piping response problems in which the forcing functions are due to fluid excitation. Application of the technique to this case is somewhat more difficult, because a well defined cutoff frequency for determining structural modes to be included has not been established. This paper outlines a method for higher mode corrections, and suggests methods to determine suitable cutoff frequencies for piping system blowdown analyses. A numerical example illustrates how uncorrected modal superposition results can produce erroneous stress results

Thermoluminescent response of LaAlO3:Pr

International Nuclear Information System (INIS)

Morales H, A.; Zarate M, J.; Azorin N, J.; Rivera M, T.

2015-10-01

In this study, the thermoluminescence response of doped lanthanum aluminate (LaAlO 3 ) with praseodymium ion (Pr) obtained by the Pechini method and drying by the spraying technique Spry Dryer was studied. The obtained powders were analyzed structurally by the X-ray diffraction technique; the morphological characterization was by the scanning electron microscopy technique. The obtained powders at 800 degrees C presented crystallinity and showed a Rhombohedral crystal structure, this phase was observed by X-ray diffraction patterns. Thermoluminescence response of LaAlO 3 :Pr showed a brightness curve with a peak centered at 157 degrees C. The sensitivity of the doped samples was improved about 90 times in comparison with the undoped sample. Thermoluminescence response in function of the wavelength showed a maximum at 230 nm, reproducibility of thermoluminescence response was ±50%. Also the fading in thermoluminescence response was studied. (Author)

Water Soluble Responsive Polymer Brushes

Directory of Open Access Journals (Sweden)

Andrew J. Parnell

2011-12-01

Full Text Available Responsive polymer brushes possess many interesting properties that enable them to control a range of important interfacial behaviours, including adhesion, wettability, surface adsorption, friction, flow and motility. The ability to design a macromolecular response to a wide variety of external stimuli makes polymer brushes an exciting class of functional materials, and has been made possible by advances in modern controlled polymerization techniques. In this review we discuss the physics of polymer brush response along with a summary of the techniques used in their synthesis. We then review the various stimuli that can be used to switch brush conformation; temperature, solvent quality, pH and ionic strength as well as the relatively new area of electric field actuation We discuss examples of devices that utilise brush conformational change, before highlighting other potential applications of responsive brushes in real world devices.

A new technique of characterization of the intra-pixel response of astronomical detectors

International Nuclear Information System (INIS)

Ketchazo, C.; Boulade, O.; Moreau, V.; Dubreuil, D.; Ronayette, S.; Berthe, M.

2014-01-01

This paper is devoted to the presentation of a new technique of characterization of the Intra-Pixel Sensitivity Variations (IPSVs) of astronomical detectors. The IPSV is the spatial variation of the sensitivity within a pixel and it was demonstrated that this variation can contribute to the instrument global error. Then IPSV has not to be neglected especially in the case of under-sampled instruments for high quality imaging and accurate photometry. The common approaches to measure the IPSV consist in determining the pixel response function (PRF) by scanning an optical probe through the detector. These approaches require high-aperture optics, high precision mechanical devices and are time consuming. The original approach we will present in this paper consists in projecting high-resolution periodic patterns onto the whole sensor without classic optics but using the self-imaging property (the Talbot effect) of a Continuously Self Imaging Grating (CSIG) illuminated by a plane wave. This paper describes the test bench and its design rules. The methodology of the measurement is also presented. Two measurement procedures are available: global and local. In the global procedure, the mean PRF corresponding to the whole Focal Plane Array (FPA) or a sub-area of the FPA is evaluated. The results obtained applying this procedure on e2v CCD 204 are presented and discussed in detail. In the local procedure, a CSIG is moved in front of each pixel and a pixel PRF is reconstructed by resolving the inverse problem. The local procedure is presented and validated by simulations. (authors)

The technique of obtaining single-energy γ-rays in calibrating energy response of detector

International Nuclear Information System (INIS)

Li Rurong; Peng Taiping; Hu Mengchun; Li Zhongbao

2004-01-01

This paper introduces the principle of transforming γ-rays from 60 Co into a series of single-energy γ-rays and stresses the technique of shielding radiation-interfere and reducing energy-dispersion. The Single-energy γ-rays of any energy in the range of 0.36-1.02 MeV may be obtained by means of this technique. (authors)

Multi-scale approach in numerical reservoir simulation; Uma abordagem multiescala na simulacao numerica de reservatorios

Energy Technology Data Exchange (ETDEWEB)

Guedes, Solange da Silva

1998-07-01

Advances in petroleum reservoir descriptions have provided an amount of data that can not be handled directly during numerical simulations. This detailed geological information must be incorporated into a coarser model during multiphase fluid flow simulations by means of some upscaling technique. the most used approach is the pseudo relative permeabilities and the more widely used is the Kyte and Berry method (1975). In this work, it is proposed a multi-scale computational model for multiphase flow that implicitly treats the upscaling without using pseudo functions. By solving a sequence of local problems on subdomains of the refined scale it is possible to achieve results with a coarser grid without expensive computations of a fine grid model. The main advantage of this new procedure is to treat the upscaling step implicitly in the solution process, overcoming some practical difficulties related the use of traditional pseudo functions. results of bidimensional two phase flow simulations considering homogeneous porous media are presented. Some examples compare the results of this approach and the commercial upscaling program PSEUDO, a module of the reservoir simulation software ECLIPSE. (author)

Treatment of anxiety: a comparison of the usefulness of self-hypnosis and a meditational relaxation technique. An overview.

Science.gov (United States)

Benson, H; Frankel, F H; Apfel, R; Daniels, M D; Schniewind, H E; Nemiah, J C; Sifneos, P E; Crassweller, K D; Greenwood, M M; Kotch, J B; Arns, P A; Rosner, B

1978-01-01

We have investigated prospectively the efficacy of two nonpharmacologic relaxation techniques in the therapy of anxiety. A simple, meditational relaxation technique (MT) that elicits the changes of decreased sympathetic nervous system activity was compared to a self-hypnosis technique (HT) in which relaxation, with or without altered perceptions, was suggested. 32 patients with anxiety neurosis were divided into 2 groups on the basis of their responsivity to hypnosis: moderate-high and low responsivity. The MT or HT was then randomly assigned separately to each member of the two responsivity groups. Thus, 4 treatment groups were studied: moderate-high responsivity MT; low responsivity MT; moderate-high responsivity HT; and low responsivity HT. The low responsivity HT group, by definition largely incapable of achieving the altered perceptions essential to hypnosis, was designed as the control group. Patients were instructed to practice the assigned technique daily for 8 weeks. Change in anxiety was determined by three types of evaluation: psychiatric assessment; physiologic testing; and self-assessment. There was essentially no difference between the two techniques in therapeutic efficacy according to these evaluations. Psychiatric assessment revealed overall improvement in 34% of the patients and the self-rating assessment indicated improvement in 63% of the population. Patients who had moderate-high hypnotic responsivity, independent of the technique used, significantly improved on psychiatric assessment (p = 0.05) and decreased average systolic blood pressure from 126.1 to 122.5 mm Hg over the 8-week period (p = 0.048). The responsivity scores at the higher end of the hypnotic responsivity spectrum were proportionately correlated to greater decreases in systolic blood pressure (p = 0.075) and to improvement by psychiatric assessment (p = 0.003). There was, however, no consistent relation between hypnotic responsivity and the other assessments made, such as

Structural response synthesis

Energy Technology Data Exchange (ETDEWEB)

Ozisik, H.; Keltie, R.F.

1988-12-01

The open loop control technique of predicting a conditioned input signal based on a specified output response for a second order system has been analyzed both analytically and numerically to gain a firm understanding of the method. Differences between this method of control and digital closed loop control using pole cancellation were investigated as a follow up to previous experimental work. Application of the technique to diamond turning using a fast tool is also discussed.

Voltage Controlled Dynamic Demand Response

DEFF Research Database (Denmark)

Bhattarai, Bishnu Prasad; Bak-Jensen, Birgitte; Mahat, Pukar

2013-01-01

Future power system is expected to be characterized by increased penetration of intermittent sources. Random and rapid fluctuations in demands together with intermittency in generation impose new challenges for power balancing in the existing system. Conventional techniques of balancing by large...... central or dispersed generations might not be sufficient for future scenario. One of the effective methods to cope with this scenario is to enable demand response. This paper proposes a dynamic voltage regulation based demand response technique to be applied in low voltage (LV) distribution feeders....... An adaptive dynamic model has been developed to determine composite voltage dependency of an aggregated load on feeder level. Following the demand dispatch or control signal, optimum voltage setting at the LV substation is determined based on the voltage dependency of the load. Furthermore, a new technique...

Techniques for data compression in experimental nuclear physics problems

International Nuclear Information System (INIS)

Byalko, A.A.; Volkov, N.G.; Tsupko-Sitnikov, V.M.

1984-01-01

Techniques and ways for data compression during physical experiments are estimated. Data compression algorithms are divided into three groups: the first one includes the algorithms based on coding and which posses only average indexes by data files, the second group includes algorithms with data processing elements, the third one - algorithms for converted data storage. The greatest promise for the techniques connected with data conversion is concluded. The techniques possess high indexes for compression efficiency and for fast response, permit to store information close to the source one

Propagation of nuclear data uncertainties in fuel cycle calculations using Monte-Carlo technique

International Nuclear Information System (INIS)

Diez, C.J.; Cabellos, O.; Martinez, J.S.

2011-01-01

Nowadays, the knowledge of uncertainty propagation in depletion calculations is a critical issue because of the safety and economical performance of fuel cycles. Response magnitudes such as decay heat, radiotoxicity and isotopic inventory and their uncertainties should be known to handle spent fuel in present fuel cycles (e.g. high burnup fuel programme) and furthermore in new fuel cycles designs (e.g. fast breeder reactors and ADS). To deal with this task, there are different error propagation techniques, deterministic (adjoint/forward sensitivity analysis) and stochastic (Monte-Carlo technique) to evaluate the error in response magnitudes due to nuclear data uncertainties. In our previous works, cross-section uncertainties were propagated using a Monte-Carlo technique to calculate the uncertainty of response magnitudes such as decay heat and neutron emission. Also, the propagation of decay data, fission yield and cross-section uncertainties was performed, but only isotopic composition was the response magnitude calculated. Following the previous technique, the nuclear data uncertainties are taken into account and propagated to response magnitudes, decay heat and radiotoxicity. These uncertainties are assessed during cooling time. To evaluate this Monte-Carlo technique, two different applications are performed. First, a fission pulse decay heat calculation is carried out to check the Monte-Carlo technique, using decay data and fission yields uncertainties. Then, the results, experimental data and reference calculation (JEFF Report20), are compared. Second, we assess the impact of basic nuclear data (activation cross-section, decay data and fission yields) uncertainties on relevant fuel cycle parameters (decay heat and radiotoxicity) for a conceptual design of a modular European Facility for Industrial Transmutation (EFIT) fuel cycle. After identifying which time steps have higher uncertainties, an assessment of which uncertainties have more relevance is performed

Empowerment methods and techniques for sport managers

Directory of Open Access Journals (Sweden)

THANOS KRIEMADIS

2006-01-01

Full Text Available We live in a globalize economic, social and technological environment where organizations can be successful only if they have required resources (material resources, facilities and equipment, and human resources. The managers and the organizations should empower and enable employees to accomplish their work in meaningful ways. Empowerment has been described as a means to enable employees to make decisions and as a personal phenomenon where individuals take responsibility for their own actions. The aim of the present study was to present effective methods and techniques of employee empowerment which constitute for the organization a source of competitive advantage. The paper will present and explain empowerment methods and techniques such as: (a organizational culture, (b vision statements, (c organizational values, (d teamwork, (e the role of manager - leadership, (f devolving responsibility accountability, (g information sharing, (h continuous training, (i appraisal rewards, (j goal setting, and (k performance appraisal process.

The Dirichet-Multinomial model for multivariate randomized response data and small samples

NARCIS (Netherlands)

Avetisyan, Marianna; Fox, Gerardus J.A.

2012-01-01

In survey sampling the randomized response (RR) technique can be used to obtain truthful answers to sensitive questions. Although the individual answers are masked due to the RR technique, individual (sensitive) response rates can be estimated when observing multivariate response data. The

Contrast-enhanced Spectral Mammography: Technique, Indications, and Clinical Applications.

Science.gov (United States)

Bhimani, Chandni; Matta, Danielle; Roth, Robyn G; Liao, Lydia; Tinney, Elizabeth; Brill, Kristin; Germaine, Pauline

2017-01-01

Contrast-enhanced spectral mammography (CESM) combines the benefits of full field digital mammography with the concept of tumor angiogenesis. Technique and practical applications of CESM are discussed. An overview of the technique is followed by a demonstration of practical applications of CESM in our practice. We have successfully implemented CESM into our practice as a screening, diagnostic, staging, and treatment response tool. It is important to understand the technique of CESM and how to incorporate it into practice. Copyright © 2017 The Association of University Radiologists. Published by Elsevier Inc. All rights reserved.

Postoperative ileus - an update on preventive techniques

DEFF Research Database (Denmark)

Kehlet, H.

2008-01-01

This article reviews techniques currently used to prevent or reduce the duration of postoperative ileus (POI), which is considered an undesirable stress response to major abdominal surgery that leads to discomfort, morbidity and prolonged hospital stay. In several randomized studies, a number...... institution of oral feeding and laparoscopic surgery might also be effective, but there is less clear evidence available to support their use. When some of these techniques are combined as part of the concept of multimodal postoperative rehabilitation (fast-track surgery), the duration of POI after open...

Waveforms and Sonic Boom Perception and Response (WSPR): Low-Boom Community Response Program Pilot Test Design, Execution, and Analysis

Science.gov (United States)

Page, Juliet A.; Hodgdon, Kathleen K.; Krecker, Peg; Cowart, Robbie; Hobbs, Chris; Wilmer, Clif; Koening, Carrie; Holmes, Theresa; Gaugler, Trent; Shumway, Durland L.;

Modelling the optical response of human retinal photoreceptors to plane wave illumination with the finite integration technique

Science.gov (United States)

Akhlagh Moayed, Alireza; Dang, Shannon; Ramahi, Omar M.; Bizheva, Kostadinka K.

2009-02-01

The early stages of ocular diseases such as Diabetic Retinopathy are manifested by morphological changes in retinal tissue occurring on cellular level. Therefore, a number of ophthalmic diseases can be diagnosed at an early stage by detecting spatial and temporal variations in the scattering profile of retinal tissue. It was recently demonstrated that, OCT can be used to probe the functional response of retinal photoreceptors to external light stimulation [1]-[3]. fUHROCT measures localized differential changes in the retina reflectivity over time resulting from external light stimulation of the retina. Currently the origins of the observed reflectivity changes are not well understood. However, due to the complex nature of retinal physiology using purely experimental approaches in this case is problematic. For example fUHROCT is sensitive to small changes in the refractive index of biological tissue which as demonstrated previously, can result from a number of processes such as membrane hyperpolarization, osmotic swelling, metabolic changes, etc. In this paper, we present a computational model of interaction between photoreceptor cells and optical plane wave based on the Finite Integration Technique (FIT).

Use of 222Rn-resistant techniques in new home construction

International Nuclear Information System (INIS)

Watson, J.E. Jr.; Cote, R.A.

1999-01-01

The objective of this project was to assess the status of the use of 222 Rn-resistant construction techniques in new home construction in the eight Zone 1 counties of North Carolina. Zone 1 counties have an average predicted indoor 222 Rn screening potential greater than 148 Bq m -3 (4 pCi L -1 ). To facilitate a response from builders, a brief survey form was designed and printed on the back of a self-addressed, postage-paid postcard. This survey form was mailed to 460 home builders in the Zone 1 counties. The response rate was 17%, which can be compared to the 4.9% response rate obtained in a national survey conducted by the National Association of Home Builders Research Center. In their survey, 62% of the responding builders reported that they had built some or many homes in 1996 using construction techniques to reduce the entry of radon into homes, but only 10% of the builders reported using these techniques for many homes. The National Association of Home Builders survey determined that, nationally, 30% of homes built in Zone 1 counties had 222 Rn venting features. There is the potential for bias in the results of their survey (as well as in the results of the National Association of Home Builders survey) since the response rates were low

Use of communication techniques by Maryland dentists.

Science.gov (United States)

Maybury, Catherine; Horowitz, Alice M; Wang, Min Qi; Kleinman, Dushanka V

2013-12-01

Health care providers' use of recommended communication techniques can increase patients' adherence to prevention and treatment regimens and improve patient health outcomes. The authors conducted a survey of Maryland dentists to determine the number and type of communication techniques they use on a routine basis. The authors mailed a 30-item questionnaire to a random sample of 1,393 general practice dentists and all 169 members of the Maryland chapter of the American Academy of Pediatric Dentistry. The overall response rate was 38.4 percent. Analysis included descriptive statistics, analysis of variance and ordinary least squares regression analysis to examine the association of dentists' characteristics with the number of communication techniques used. They set the significance level at P communication techniques and 3.6 of the seven basic techniques, whereas pediatric dentists reported using a mean of 8.4 and 3.8 of those techniques, respectively. General dentists who had taken a communication course outside of dental school were more likely than those who had not to use the 18 techniques (P communication course outside of dental school were more likely than those who had not to use the 18 techniques (P communication techniques that dentists used routinely varied across the 18 techniques and was low for most techniques. Practical Implications. Professional education is needed both in dental school curricula and continuing education courses to increase use of recommended communication techniques. Specifically, dentists and their team members should consider taking communication skills courses and conducting an overall evaluation of their practices for user friendliness.

Numerical Computational Technique for Scattering from Underwater Objects

OpenAIRE

T. Ratna Mani; Raj Kumar; Odamapally Vijay Kumar

2013-01-01

This paper presents a computational technique for mono-static and bi-static scattering from underwater objects of different shape such as submarines. The scatter has been computed using finite element time domain (FETD) method, based on the superposition of reflections, from the different elements reaching the receiver at a particular instant in time. The results calculated by this method has been verified with the published results based on ramp response technique. An in-depth parametric s...

Response of sunflower to various pre-germination techniques for breaking seed dormancy

International Nuclear Information System (INIS)

Nasreen, S.; Khan, M.A.; Uddin, S.

2015-01-01

Seed dormancy is considered to be a serious constraint in sunflower seed production. Viable seeds sometimes do not germinate even in the presence of favorable environmental conditions. Such seeds are suspected to be dormant. The study was conducted under controlled/laboratory conditions during spring 2010 at National Agricultural Research Centre, Islamabad. The objective of the study was to evaluate some techniques to convert a seed from dormant to non-dormant germinable state. Dormant seeds of 21 sunflower hybrids were treated with three hot water treatments (100/80 degree C) and four chemicals potassium nitrate, 0.2%, thiourea, 0.5%, ethanol, 25%, acetone, 25% for breaking seed dormancy .The untreated seed was taken as control. Soaking seeds in hot water (80 degree C) for 15 minutes followed by one day dry and seed treatment with acetone were found to be the most effective and successful techniques in converting the seed from dormant to non-dormant state. (author)

Self-Guided Collaboration: A Technique to Coordinate Crisis Management Response for Homeland Defense

National Research Council Canada - National Science Library

Leary, Alison E; Shaker, Steven M

2004-01-01

.... One basic step is to enable organizations to determine the strengths, capabilities, techniques and equipment, personnel skills, talent, and other offerings, which various organizations can contribute...

Selected techniques in water resources investigations, 1965

Science.gov (United States)

Mesnier, Glennon N.; Chase, Edith B.

1966-01-01

Increasing world activity in water-resources development has created an interest in techniques for conducting investigations in the field. In the United States, the Geological Survey has the responsibility for extensive and intensive hydrologic studies, and the Survey places considerable emphasis on discovering better ways to carry out its responsibility. For many years, the dominant interest in field techniques has been "in house," but the emerging world interest has led to a need for published accounts of this progress. In 1963 the Geological Survey published "Selected Techniques in Water Resources Investigations" (Water-Supply Paper 1669-Z) as part of the series "Contributions to the Hydrology of the United States."The report was so favorably received that successive volumes are planned, of which this is the first. The present report contains 25 papers that represent new ideas being tested or applied in the hydrologic field program of the Geological Survey. These ideas range from a proposed system for monitoring fluvial sediment to how to construct stream-gaging wells from steel oil drums. The original papers have been revised and edited by the compilers, but the ideas presented are those of the authors. The general description of the bubble gage on page 2 has been given by the compilers as supplementary information.

Health risk characterization of chlorpyrifos using epidemiological dose-response data and probabilistic techniques: a case study with rice farmers in Vietnam.

Science.gov (United States)

Phung, Dung Tri; Connell, Des; Yu, Qiming; Chu, Cordia

2013-09-01

Various methods for risk characterization have been developed using probabilistic approaches. Data on Vietnamese farmers are available for the comparison of outcomes for risk characterization using different probabilistic methods. This article addresses the health risk characterization of chlorpyrifos using epidemiological dose-response data and probabilistic techniques obtained from a case study with rice farmers in Vietnam. Urine samples were collected from farmers and analyzed for trichloropyridinol (TCP), which was converted into absorbed daily dose of chlorpyrifos. Adverse health response doses due to chlorpyrifos exposure were collected from epidemiological studies to develop dose-adverse health response relationships. The health risk of chlorpyrifos was quantified using hazard quotient (HQ), Monte Carlo simulation (MCS), and overall risk probability (ORP) methods. With baseline (prior to pesticide spraying) and lifetime exposure levels (over a lifetime of pesticide spraying events), the HQ ranged from 0.06 to 7.1. The MCS method indicated less than 0.05% of the population would be affected while the ORP method indicated that less than 1.5% of the population would be adversely affected. With postapplication exposure levels, the HQ ranged from 1 to 32.5. The risk calculated by the MCS method was that 29% of the population would be affected, and the risk calculated by ORP method was 33%. The MCS and ORP methods have advantages in risk characterization due to use of the full distribution of data exposure as well as dose response, whereas HQ methods only used the exposure data distribution. These evaluations indicated that single-event spraying is likely to have adverse effects on Vietnamese rice farmers. © 2013 Society for Risk Analysis.

Lymphocyte labelling technique for the exploration of kidney transplants

International Nuclear Information System (INIS)

Guey, A.; Touraine, J.L.; Collard, M.; Claveyrolas, P.; Bouteiller, O. de; Traeger, J.

The labelling technique is developed with a precise clinical exploration in view and has to take into account the following rules or conditions: - the blood sample must be smaller than 20 ml; - the manipulation must not last more than 3 hours; - the immunological properties of the labelled lymphocytes must be kept intact; - the solution reinjected into the patient must contain no aggregates, be absolutely sterile and possess a radioactivity above 1mCi. The technique of extraction and labelling from a sample of about 15ml is described. The main factors responsible for the quality of the labelling are analysed, together with the labelling and irradiation dose effects on certain properties of the lymphocytes (viability, rosette E formation, proliferative response to mitogens) [fr

Analytical Techniques and the Air Force Logistics Readiness Officer

National Research Council Canada - National Science Library

Main, Bryan D

2008-01-01

.... Over 500 LROs and supervisors provided inputs. Analysis of survey responses found that Forecasting, Graphical Statistics, and Descriptive Statistics are the analytical techniques valued most by both LROs and their supervisors...

Evaluation of patient response and recurrence of pigmentation following gingival depigmentation using laser and scalpel technique: A clinical study

Directory of Open Access Journals (Sweden)

Harpreet Singh Grover

2014-01-01

Full Text Available Aim: The present study was undertaken to evaluate patient response and recurrence of pigmentation following gingival depigmentation carried out with a surgical blade and diode laser. Materials and Methods: Twenty patients who were esthetically conscious of their dark gums and requested treatment for the same were selected for this study. Complete phase I therapy was performed for all the patients before performing the gingival depigmentation procedures with laser and scalpel on a split-mouth basis. Patients were evaluated for pain (1 day, 1 week, wound healing and melanin repigmentation (Melanin Pigmentation Index immediately and at 1 week, 1 month and 3 months, respectively. Results: The final results were statistically analyzed and significance was evaluated. The results of this study indicated that both scalpel and laser were efficient for gingival depigmentation. Comparative pain assessment (P = 0.148 and repigmentation scores (P = 0.288 at various time intervals between the two groups did not show any statistical significance. Conclusion: Both the procedures did not result in any post-operative complications and the gingiva healed uneventfully. When compared, both the techniques were found to be equally efficacious. Care must be taken to assess the gingival biotype and the degree of pigmentation in deciding which technique is to be used. Clinical Significance: Various methods of depigmentation are available with comparable efficacies. Depigmentation is not a clinical indication but a treatment of choice where esthetics is a concern and is desired by the patient.

A concise account of techniques available for shipboard sea state estimation

DEFF Research Database (Denmark)

Nielsen, Ulrik Dam

2017-01-01

This article gives a review of techniques applied to make sea state estimation on the basis of measured responses on a ship. The general concept of the procedures is similar to that of a classical wave buoy, which exploits a linear assumption between waves and the associated motions. In the frequ......This article gives a review of techniques applied to make sea state estimation on the basis of measured responses on a ship. The general concept of the procedures is similar to that of a classical wave buoy, which exploits a linear assumption between waves and the associated motions...

Promoting Response Variability and Stimulus Generalization in Martial Arts Training

Science.gov (United States)

Harding, Jay W.; Wacker, David P.; Berg, Wendy K.; Rick, Gary; Lee, John F.

2004-01-01

The effects of reinforcement and extinction on response variability and stimulus generalization in the punching and kicking techniques of 2 martial arts students were evaluated across drill and sparring conditions. During both conditions, the students were asked to demonstrate different techniques in response to an instructor's punching attack.…

Linux Incident Response Volatile Data Analysis Framework

Science.gov (United States)

McFadden, Matthew

2013-01-01

Cyber incident response is an emphasized subject area in cybersecurity in information technology with increased need for the protection of data. Due to ongoing threats, cybersecurity imposes many challenges and requires new investigative response techniques. In this study a Linux Incident Response Framework is designed for collecting volatile data…

Location Privacy Techniques in Client-Server Architectures

DEFF Research Database (Denmark)

Jensen, Christian Søndergaard; Lu, Hua; Yiu, Man Lung

2009-01-01

A typical location-based service returns nearby points of interest in response to a user location. As such services are becoming increasingly available and popular, location privacy emerges as an important issue. In a system that does not offer location privacy, users must disclose their exact...... locations in order to receive the desired services. We view location privacy as an enabling technology that may lead to increased use of location-based services. In this chapter, we consider location privacy techniques that work in traditional client-server architectures without any trusted components other....... Third, their effectiveness is independent of the distribution of other users, unlike the k-anonymity approach. The chapter characterizes the privacy models assumed by existing techniques and categorizes these according to their approach. The techniques are then covered in turn according...

Response matrix method for large LMFBR analysis

International Nuclear Information System (INIS)

King, M.J.

1977-06-01

The feasibility of using response matrix techniques for computational models of large LMFBRs is examined. Since finite-difference methods based on diffusion theory have generally found a place in fast-reactor codes, a brief review of their general matrix foundation is given first in order to contrast it to the general strategy of response matrix methods. Then, in order to present the general method of response matrix technique, two illustrative examples are given. Matrix algorithms arising in the application to large LMFBRs are discussed, and the potential of the response matrix method is explored for a variety of computational problems. Principal properties of the matrices involved are derived with a view to application of numerical methods of solution. The Jacobi iterative method as applied to the current-balance eigenvalue problem is discussed

The Dirichlet-Multinomial Model for Multivariate Randomized Response Data and Small Samples

Science.gov (United States)

Avetisyan, Marianna; Fox, Jean-Paul

2012-01-01

In survey sampling the randomized response (RR) technique can be used to obtain truthful answers to sensitive questions. Although the individual answers are masked due to the RR technique, individual (sensitive) response rates can be estimated when observing multivariate response data. The beta-binomial model for binary RR data will be generalized…

Cuprous oxide thin films grown by hydrothermal electrochemical deposition technique

International Nuclear Information System (INIS)

Majumder, M.; Biswas, I.; Pujaru, S.; Chakraborty, A.K.

2015-01-01

Semiconducting cuprous oxide films were grown by a hydrothermal electro-deposition technique on metal (Cu) and glass (ITO) substrates between 60 °C and 100 °C. X-ray diffraction studies reveal the formation of cubic cuprous oxide films in different preferred orientations depending upon the deposition technique used. Film growth, uniformity, grain size, optical band gap and photoelectrochemical response were found to improve in the hydrothermal electrochemical deposition technique. - Highlights: • Cu 2 O thin films were grown on Cu and glass substrates. • Conventional and hydrothermal electrochemical deposition techniques were used. • Hydrothermal electrochemical growth showed improved morphology, thickness and optical band gap

Techniques for the design of highly damped structures

International Nuclear Information System (INIS)

Nelson, F.C.

1975-01-01

This paper discusses several techniques for the design of highly damped structures, techniques which have proven successful for large scale, low frequency steel and concrete structures which are typical of nuclear power reactors and their components. The ability to augment structural damping can be useful in increasing the seismic withstandability of structures. Seismic excitation is broadband in its frequency content and will excite many strutural resonances. Broadband damping will limit these resonant responses and thereby reduce the seismic load on structures and their components. This paper discusses three techniques: the design of structural joints and interfaces to promote damping; the use of layers of viscoelastic material; and the employment of damping links. The emphasis is on explaining the ways in which these techniques work and in describing the ways in which they have been used. (Auth.)

Detecting Careless Responses to Self-Reported Questionnaires

Science.gov (United States)

Kountur, Ronny

2016-01-01

Problem Statement: The use of self-report questionnaires may lead to biases such as careless responses that distort the research outcomes. Early detection of careless responses in self-report questionnaires may reduce error, but little guidance exists in the literature regarding techniques for detecting such careless or random responses in…

Frequency response of electrochemical cells

Science.gov (United States)

Thomas, Daniel L.

1990-01-01

The main objective was to examine the feasibility of using frequency response techniques (1) as a tool in destructive physical analysis of batteries, particularly for estimating electrode structural parameters such as specific area, porosity, and tortuosity and (2) as a non-destructive testing technique for obtaining information such as state of charge and acceptability for space flight. The phenomena that contribute to the frequency response of an electrode include: (1) double layer capacitance; (2) Faradaic reaction resistance; (3) mass transfer of Warburg impedance; and (4) ohmic solution resistance. Nickel cadmium cells were investigated in solutions of KOH. A significant amount of data was acquired. Quantitative data analysis, using the developed software, is planned for the future.

Turning negative memories around: Contingency versus devaluation techniques.

Science.gov (United States)

Dibbets, Pauline; Lemmens, Anke; Voncken, Marisol

2018-09-01

It is assumed that fear responses can be altered by changing the contingency between a conditioned stimulus (CS) and an unconditioned stimulus (US), or by devaluing the present mental representation of the US. The aim of the present study was to compare the efficacy of contingency- and devaluation-based intervention techniques on the diminishment in - and return of fear. We hypothesized that extinction (EXT, contingency-based) would outperform devaluation-based techniques regarding contingency measures, but that devaluation-based techniques would be most effective in reducing the mental representation of the US. Additionally, we expected that incorporations of the US during devaluation would result in less reinstatement of the US averseness. Healthy participants received a fear conditioning paradigm followed by one of three interventions: extinction (EXT, contingency-based), imagery rescripting (ImRs, devaluation-based) or eye movement desensitization and reprocessing (EMDR, devaluation-based). A reinstatement procedure and test followed the next day. EXT was indeed most successful in diminishing contingency-based US expectancies and skin conductance responses (SCRs), but all interventions were equally successful in reducing the averseness of the mental US representation. After reinstatement EXT showed lowest expectancies and SCRs; no differences were observed between the conditions concerning the mental US representation. A partial reinforcement schedule was used, resulting in a vast amount of contingency unaware participants. Additionally, a non-clinical sample was used, which may limit the generalizability to clinical populations. EXT is most effective in reducing conditioned fear responses. Copyright © 2018 Elsevier Ltd. All rights reserved.

Growth, morphological properties and pulsed photo response of MoTe2 single crystal synthesized by DVT technique

Science.gov (United States)

Dixit, Vijay; Vyas, Chirag; Patel, Abhishek; Pathak, V. M.; Solanki, G. K.; Patel, K. D.

2018-05-01

Molybednum Di Telluride of group VI belongs to the family of layered transition metal di-chalcogenides (TMDCs). These TMDCs show good potential for applications in the field of optoelectronic devices as they are chemically inert trilayered structure of MX2 type. In the present investigation crystals of MoTe2 are grown by direct vapor transport technique in a dual zone horizontal furnace. The grown crystals were characterized by Energy Dispersive Analysis of X-rays (EDAX) to study its elemental and stoichiometric composition, Selected Area Electron Diffraction (SAED) confirms the hexagonal structure. Spot pattern of electron diffraction shows formation of single phase. Scanning Electron Microscope (SEM) shows the layer by layer growth of the crystals, Thermo Electric Power (TEP) reflects the p-type semiconducting nature of the grown crystals. As this material is photosensitive material having band gap of approximately 1.0 eV, a transient photo response against polychromatic radiation (40 mW/cm2) of photodetector is also measured which showed slow decay in generated photocurrent due to low trapping density within the active area of the prepared device. Thus, it shows that this material can be a good photovoltaic material for constructing a solar cell also.

Comparison of MOS capacitor and transistor postirradiation response

International Nuclear Information System (INIS)

McWhorter, P.J.; Fleetwood, D.M.; Pastorek, R.A.; Zimmerman, G.T.

1989-01-01

The postirradiation response of MOS capacitors and transistors fabricated on the same chip has been examined as a function of dose and anneal bias. A variety of analysis techniques are used to evaluate the postirradiation response of these structures, including low and high frequency capacitance-voltage techniques, subthreshold current-voltage techniques, and charge pumping. Though there are changes in the postirradiation energy spectrum of ΔD it , no clear evidence of defect transformation is observed on transistors or capacitors under any conditions examined. Postirradiation response at 80 degrees C is found to be similar in the two structures for low levels of damage (100 krad). For both structures, interface-trap densities continue to grow following irradiation under these conditions. In contrast, the postirradiation response of capacitors and transistors can differ qualitatively at higher levels of damage (1 Mrad), with interface-traps increasing postirradiation at 80 degrees C for transistors and annealing for capacitors. These results indicate that capacitor structures may not be suitable for hardness assurance studies that involve elevated temperature irradiations or postirradiation anneals

Plasmapheresis and other extracorporeal filtration techniques in critical patients.

Science.gov (United States)

Daga Ruiz, D; Fonseca San Miguel, F; González de Molina, F J; Úbeda-Iglesias, A; Navas Pérez, A; Jannone Forés, R

2017-04-01

Plasmapheresis is an extracorporeal technique that eliminates macromolecules involved in pathological processes from plasma. A review is made of the technical aspects, main indications in critical care and potential complications of plasmapheresis, as well as of other extracorporeal filtration techniques such as endotoxin-removal columns and other devices designed to eliminate cytokines or modulate the inflammatory immune response in critical patients. Copyright © 2016 Elsevier España, S.L.U. y SEMICYUC. All rights reserved.

Mastering data warehouse design relational and dimensional techniques

CERN Document Server

Imhoff, Claudia; Geiger, Jonathan G

2003-01-01

A cutting-edge response to Ralph Kimball''s challenge to the data warehouse community that answers some tough questions about the effectiveness of the relational approach to data warehousingWritten by one of the best-known exponents of the Bill Inmon approach to data warehousingAddresses head-on the tough issues raised by Kimball and explains how to choose the best modeling technique for solving common data warehouse design problemsWeighs the pros and cons of relational vs. dimensional modeling techniquesFocuses on tough modeling problems, including creating and maintaining keys and modeling c

Critical Response Protocol

Science.gov (United States)

Ellingson, Charlene; Roehrig, Gillian; Bakkum, Kris; Dubinsky, Janet M.

2016-01-01

This article introduces the Critical Response Protocol (CRP), an arts-based technique that engages students in equitable critical discourse and aligns with the "Next Generation Science Standards" vision for providing students opportunities for language learning while advancing science learning (NGSS Lead States 2013). CRP helps teachers…

Optimizing and modeling of effective parameters on the structural and magnetic properties of Fe{sub 3}O{sub 4} nanoparticles synthesized by coprecipitation technique using response surface methodology

Energy Technology Data Exchange (ETDEWEB)

Ghazanfari, Mohammad Reza [Department of Materials Science and Engineering, Ferdowsi University of Mashhad, 9177948974 Mashhad (Iran, Islamic Republic of); Kashefi, Mehrdad, E-mail: m-kashefi@um.ac.ir [Department of Materials Science and Engineering, Ferdowsi University of Mashhad, 9177948974 Mashhad (Iran, Islamic Republic of); Jaafari, Mahmoud Reza [Biotechnology Research Center, Nanotechnology Research Center, School of Pharmacy, Mashhad University of Medical Sciences, Mashhad (Iran, Islamic Republic of)

2016-07-01

In present work, the Fe{sub 3}O{sub 4} magnetic nanoparticles were successfully synthesized by coprecipitation method. In order to study the effects of influential factors on the structural and magnetic properties of particles, the experimental runs were designed using response surface methodology (RSM) based on central composite design (CCD), while the reaction temperature, Fe{sup 2+}/Fe{sup 3+} cation ratio, and pH of reaction were defined as effective factors on the two responses include the amounts of crystallinity degree and saturation magnetization (M{sub s}). The investigation of structural, magnetic, and microstructural properties of particles were carried out by X-ray diffraction (XRD), vibrating sample magnetometer (VSM), and dynamic light scattering (DLS) and transmission electron microscopy (TEM) analyses. As a result, the predictive quadratic models were fitted on the both responses while the R{sup 2} values were more than 0.97 for both models. The highest amounts of both responses (crystallinity degree: 88.07% and M{sub s}: 65.801 emu/g) are presented when the reaction temperature, cation ratio, and pH amounts are equal to 90 °C, 0.60, and 10.5, respectively. Finally, the TEM results show the particles with size of about 10 nm and narrow size distribution. - Highlights: • The Fe{sub 3}O{sub 4} nanoparticles were successfully synthesized by coprecipitation method. • By RSM technique, the predictive models were presented for crystallinity degree. • By RSM technique, the predictive models were presented for amounts of M{sub s}. • Temperature, pH and their interactions had most effectiveness on the amounts of M{sub s}. • Temperature, cation ratio and their interactions had most effectiveness on the crystallinity degree.

Assessing a new gene expression analysis technique for radiation biodosimetry applications

Energy Technology Data Exchange (ETDEWEB)

Manning, Grainne; Kabacik, Sylwia; Finnon, Paul; Paillier, Francois; Bouffler, Simon [Cancer Genetics and Cytogenetics, Biological Effects Department, Centre for Radiation, Chemical and Environmental Hazards, Health Protection Agency, Chilton, Didcot, Oxfordshire OX11 ORQ (United Kingdom); Badie, Christophe, E-mail: christophe.badie@hpa.org.uk [Cancer Genetics and Cytogenetics, Biological Effects Department, Centre for Radiation, Chemical and Environmental Hazards, Health Protection Agency, Chilton, Didcot, Oxfordshire OX11 ORQ (United Kingdom)

2011-09-15

The response to any radiation accident or incident involving actual or potential ionising radiation exposure requires accurate and rapid assessment of the doses received by individuals. The techniques available today for biodosimetry purposes are not fully adapted to rapid high-throughput measurements of exposures in large numbers of individuals. A recently emerging technique is based on gene expression analysis, as there are a number of genes which are radiation responsive in a dose-dependent manner. The present work aimed to assess a new technique which allows the detection of the level of expression of up to 800 genes without need of enzymatic reactions. In order to do so, human peripheral blood was exposed ex vivo to a range of x-ray doses from 5 mGy to 4 Gy of x-rays and the transcriptional expression of five radiation-responsive genes PHPT1, PUMA, CCNG1, DDB2 and MDM2 was studied by both the nCounter Digital Analyzer and Multiplex Quantitative Real-Time Polymerase Chain Reaction (MQRT-PCR) as the benchmark technology. Results from both techniques showed good correlation for all genes with R{sup 2} values ranging between 0.8160 and 0.9754. The reproducibility of the nCounter Digital Analyzer was also assessed in independent biological replicates and proved to be good. Although the slopes of the correlation of results obtained by the techniques suggest that MQRT-PCR is more sensitive than the nCounter Digital Analyzer, the nCounter Digital Analyzer provides sensitive and reliable data on modifications in gene expression in human blood exposed to radiation without enzymatic amplification of RNA prior to analysis.

Diagnostic techniques in deflagration and detonation studies.

Science.gov (United States)

Proud, William G; Williamson, David M; Field, John E; Walley, Stephen M

2015-12-01

Advances in experimental, high-speed techniques can be used to explore the processes occurring within energetic materials. This review describes techniques used to study a wide range of processes: hot-spot formation, ignition thresholds, deflagration, sensitivity and finally the detonation process. As this is a wide field the focus will be on small-scale experiments and quantitative studies. It is important that such studies are linked to predictive models, which inform the experimental design process. The stimuli range includes, thermal ignition, drop-weight, Hopkinson Bar and Plate Impact studies. Studies made with inert simulants are also included as these are important in differentiating between reactive response and purely mechanical behaviour.

Nonlinear dynamic macromodeling techniques for audio systems

Science.gov (United States)

Ogrodzki, Jan; Bieńkowski, Piotr

2015-09-01

This paper develops a modelling method and a models identification technique for the nonlinear dynamic audio systems. Identification is performed by means of a behavioral approach based on a polynomial approximation. This approach makes use of Discrete Fourier Transform and Harmonic Balance Method. A model of an audio system is first created and identified and then it is simulated in real time using an algorithm of low computational complexity. The algorithm consists in real time emulation of the system response rather than in simulation of the system itself. The proposed software is written in Python language using object oriented programming techniques. The code is optimized for a multithreads environment.

Progress in diagnostic techniques for sc cavities

International Nuclear Information System (INIS)

Reece, C.E.

1988-01-01

While routinely achieved performance characteristics of superconducting cavities have now reached a level which makes them useful in large scale applications, achieving this level has come only through the knowledge gained by systematic studies of performance limiting phenomena. Despite the very real progress that has been made, the routine performance of superconducting cavities still falls far short of both the theoretical expectations and the performance of a few exception examples. It is the task of systematically applied diagnostic techniques to reveal additional information concerning the response of superconducting surfaces to applied RF fields. Here recent developments in diagnostic techniques are discussed. 18 references, 12 figures

Calibration technique for the neutron surface moisture measurement system

International Nuclear Information System (INIS)

Watson, W.T.; Shreve, D.C.

1996-01-01

A technique for calibrating the response of a surface neutron moisture measurement probe to material moisture concentration has been devised. Tests to ensure that the probe will function in the expected in-tank operating environment are also outlined

MRI dosimetry using an echo-quotient technique for high dose rate brachytherapy

International Nuclear Information System (INIS)

Ansbacher, W.

1996-01-01

MRI gel dosimetry is a relatively new technique that has many advantages over conventional methods, and is particularly suited to High Dose Rate (HDR) Brachytherapy. The dosimeter has high spatial resolution and a water-equivalent response over a wide range of photon energies. Because it is an integrating dosimeter, it allows for efficient mapping of the dynamically-produced distributions from an HDR source. As an example of this technique, the dose response, which is calibrated in terms of the change in spin-spin relaxation time, has been used to investigate the anisotropy of an HDR source. (author). 1 fig

A microculture technique for rat lymphocyte transformation.

Science.gov (United States)

Lindsay, V J; Allardyce, R A

1979-01-01

We report the development of an economical microculture technique suitable for measuring rat lymphocyte response to mitogens and in mixed lymphocyte reactions. The effects of varying culture conditions, i.e. source of serum, addition and concentration of 2-mercaptoethanol, mitogen concentrations, culture incubation times, absorption of serum, lymphocyte numbers and microtitre plate well shape are described.

Mahalanobis distance and variable selection to optimize dose response

International Nuclear Information System (INIS)

Moore, D.H. II; Bennett, D.E.; Wyrobek, A.J.; Kranzler, D.

1979-01-01

A battery of statistical techniques are combined to improve detection of low-level dose response. First, Mahalanobis distances are used to classify objects as normal or abnormal. Then the proportion classified abnormal is regressed on dose. Finally, a subset of regressor variables is selected which maximizes the slope of the dose response line. Use of the techniques is illustrated by application to mouse sperm damaged by low doses of x-rays

Modern Methodology and Techniques Aimed at Developing the Environmentally Responsible Personality

Science.gov (United States)

Ponomarenko, Yelena V.; Zholdasbekova, Bibisara A.; Balabekov, Aidarhan T.; Kenzhebekova, Rabiga I.; Yessaliyev, Aidarbek A.; Larchenkova, Liudmila A.

2016-01-01

The article discusses the positive impact of an environmentally responsible individual as the social unit able to live in harmony with the natural world, himself/herself and other people. The purpose of the article is to provide theoretical substantiation of modern teaching methods. The authors considered the experience of philosophy, psychology,…

Uncertainty analysis technique of dynamic response and cumulative damage properties of piping system

International Nuclear Information System (INIS)

Suzuki, Kohei; Aoki, Shigeru; Hara, Fumio; Hanaoka, Masaaki; Yamashita, Tadashi.

1982-01-01

It is a technologically important subject to establish the method of uncertainty analysis statistically examining the variation of the earthquake response and damage properties of equipment and piping system due to the change of input load and the parameters of structural system, for evaluating the aseismatic capability and dynamic structural reliability of these systems. The uncertainty in the response and damage properties when equipment and piping system are subjected to excessive vibration load is mainly dependent on the irregularity of acting input load such as the unsteady vibration of earthquakes, and structural uncertainty in forms and dimensions. This study is the basic one to establish the method for evaluating the uncertainty in the cumulative damage property at the time of resonant vibration of piping system due to the disperse of structural parameters with a simple model. First, the piping models with simple form were broken by resonant vibration, and the uncertainty in the cumulative damage property was evaluated. Next, the response analysis using an elasto-plastic mechanics model was performed by numerical simulation. Finally, the method of uncertainty analysis for response and damage properties by the perturbation method utilizing equivalent linearization was proposed, and its propriety was proved. (Kako, I.)

Numerical model updating technique for structures using firefly algorithm

Science.gov (United States)

Sai Kubair, K.; Mohan, S. C.

2018-03-01

Numerical model updating is a technique used for updating the existing experimental models for any structures related to civil, mechanical, automobiles, marine, aerospace engineering, etc. The basic concept behind this technique is updating the numerical models to closely match with experimental data obtained from real or prototype test structures. The present work involves the development of numerical model using MATLAB as a computational tool and with mathematical equations that define the experimental model. Firefly algorithm is used as an optimization tool in this study. In this updating process a response parameter of the structure has to be chosen, which helps to correlate the numerical model developed with the experimental results obtained. The variables for the updating can be either material or geometrical properties of the model or both. In this study, to verify the proposed technique, a cantilever beam is analyzed for its tip deflection and a space frame has been analyzed for its natural frequencies. Both the models are updated with their respective response values obtained from experimental results. The numerical results after updating show that there is a close relationship that can be brought between the experimental and the numerical models.

Humanitarian response: improving logistics to save lives.

Science.gov (United States)

McCoy, Jessica

2008-01-01

Each year, millions of people worldwide are affected by disasters, underscoring the importance of effective relief efforts. Many highly visible disaster responses have been inefficient and ineffective. Humanitarian agencies typically play a key role in disaster response (eg, procuring and distributing relief items to an affected population, assisting with evacuation, providing healthcare, assisting in the development of long-term shelter), and thus their efficiency is critical for a successful disaster response. The field of disaster and emergency response modeling is well established, but the application of such techniques to humanitarian logistics is relatively recent. This article surveys models of humanitarian response logistics and identifies promising opportunities for future work. Existing models analyze a variety of preparation and response decisions (eg, warehouse location and the distribution of relief supplies), consider both natural and manmade disasters, and typically seek to minimize cost or unmet demand. Opportunities to enhance the logistics of humanitarian response include the adaptation of models developed for general disaster response; the use of existing models, techniques, and insights from the literature on commercial supply chain management; the development of working partnerships between humanitarian aid organizations and private companies with expertise in logistics; and the consideration of behavioral factors relevant to a response. Implementable, realistic models that support the logistics of humanitarian relief can improve the preparation for and the response to disasters, which in turn can save lives.

Modeling ionospheric foF 2 response during geomagnetic storms using neural network and linear regression techniques

Science.gov (United States)

Tshisaphungo, Mpho; Habarulema, John Bosco; McKinnell, Lee-Anne

2018-06-01

In this paper, the modeling of the ionospheric foF 2 changes during geomagnetic storms by means of neural network (NN) and linear regression (LR) techniques is presented. The results will lead to a valuable tool to model the complex ionospheric changes during disturbed days in an operational space weather monitoring and forecasting environment. The storm-time foF 2 data during 1996-2014 from Grahamstown (33.3°S, 26.5°E), South Africa ionosonde station was used in modeling. In this paper, six storms were reserved to validate the models and hence not used in the modeling process. We found that the performance of both NN and LR models is comparable during selected storms which fell within the data period (1996-2014) used in modeling. However, when validated on storm periods beyond 1996-2014, the NN model gives a better performance (R = 0.62) compared to LR model (R = 0.56) for a storm that reached a minimum Dst index of -155 nT during 19-23 December 2015. We also found that both NN and LR models are capable of capturing the ionospheric foF 2 responses during two great geomagnetic storms (28 October-1 November 2003 and 6-12 November 2004) which have been demonstrated to be difficult storms to model in previous studies.

The effectiveness of two novel techniques in establishing the mechanical and contractile responses of biceps femoris

International Nuclear Information System (INIS)

Ditroilo, Massimiliano; De Vito, Giuseppe; Hunter, Angus M; Haslam, Samuel

2011-01-01

Portable tensiomyography (TMG) and myotonometry (MMT) devices have been developed to measure mechanical and contractile properties of skeletal muscle. The aim of this study was to explore the sensitivity of the aforementioned techniques in detecting a change in passive mechanical properties of the biceps femoris (BF) muscle as a result of change in knee joint angle (i.e. muscle length). BF responses were assessed in 16 young participants (23.4 ± 4.9 years), at three knee joint angles (0°, 45° and 90°), for maximal isometric torque (MIT) along with myo-electrical activity. Contractile and mechanical properties were measured in a relaxed state. Inter-day reliability of the TMG and MMT was also assessed. MIT changed significantly (p < 0.01) across the three angles, so did stiffness and other parameters measured with MMT (p < 0.01). Conversely, TMG could detect changes only at two knee angles (0° and 45°, p < 0.01), when there is enough tension in the muscle. Reliability was overall insufficient for TMG whilst absolute reliability was excellent (coefficient of variation < 5%) for MMT. The ability of MMT more than TMG to detect an inherent change in stiffness can be conceivably exploited in a number of clinical/therapeutic applications that have to do with unnatural changes in passive muscle stiffness

Dynamic Tensile Experimental Techniques for Geomaterials: A Comprehensive Review

Science.gov (United States)

Heard, W.; Song, B.; Williams, B.; Martin, B.; Sparks, P.; Nie, X.

2018-01-01

This review article is dedicated to the Dynamic Behavior of Materials Technical Division for celebrating the 75th anniversary of the Society for Experimental Mechanics (SEM). Understanding dynamic behavior of geomaterials is critical for analyzing and solving engineering problems of various applications related to underground explosions, seismic, airblast, and penetration events. Determining the dynamic tensile response of geomaterials has been a great challenge in experiments due to the nature of relatively low tensile strength and high brittleness. Various experimental approaches have been made in the past century, especially in the most recent half century, to understand the dynamic behavior of geomaterials in tension. In this review paper, we summarized the dynamic tensile experimental techniques for geomaterials that have been developed. The major dynamic tensile experimental techniques include dynamic direct tension, dynamic split tension, and spall tension. All three of the experimental techniques are based on Hopkinson or split Hopkinson (also known as Kolsky) bar techniques and principles. Uniqueness and limitations for each experimental technique are also discussed.

The three-portal technique in arthroscopic lateral epicondylitis release

Directory of Open Access Journals (Sweden)

Ashok Gowda

2017-01-01

Full Text Available Lateral epicondylitis, commonly referred to as tennis elbow, is a syndrome characterized by pain over the origin of the common extensor muscles of the fingers, hand and wrist at the lateral epicondyle. Reports of 70-90% response to conservative treatment at one year have been documented in the literature though refractory cases often require surgical management. Arthroscopic treatment of lateral epicondylitis allows for intra-articular visualization for concomitant pathology and localization of the Extensor Carpi Radialis Brevis tendon. Additionally, compared to the open technique, the arthroscopic technique has a lower morbidity and an earlier return to work and activity. Here we describe a three portal technique for improved visualization in arthroscopic lateral epicondylitis release.

The Three-Portal Technique in Arthroscopic Lateral Epicondylitis Release.

Science.gov (United States)

Gowda, Ashok; Kennedy, Gannon; Gallacher, Stacey; Garver, Jennie; Blaine, Theodore

2016-11-17

Lateral epicondylitis, commonly referred to as tennis elbow, is a syndrome characterized by pain over the origin of the common extensor muscles of the fingers, hand and wrist at the lateral epicondyle. Reports of 70-90% response to conservative treatment at one year have been documented in the literature though refractory cases often require surgical management. Arthroscopic treatment of lateral epicondylitis allows for intra-articular visualization for concomitant pathology and localization of the Extensor Carpi Radialis Brevis tendon. Additionally, compared to the open technique, the arthroscopic technique has a lower morbidity and an earlier return to work and activity. Here we describe a three portal technique for improved visualization in arthroscopic lateral epicondylitis release.

Advances in Proteomic Techniques for Cytokine Analysis: Focus on Melanoma Research

Directory of Open Access Journals (Sweden)

Helena Kupcova Skalnikova

2017-12-01

Full Text Available Melanoma is a skin cancer with permanently increasing incidence and resistance to therapies in advanced stages. Reports of spontaneous regression and tumour infiltration with T-lymphocytes makes melanoma candidate for immunotherapies. Cytokines are key factors regulating immune response and intercellular communication in tumour microenvironment. Cytokines may be used in therapy of melanoma to modulate immune response. Cytokines also possess diagnostic and prognostic potential and cytokine production may reflect effects of immunotherapies. The purpose of this review is to give an overview of recent advances in proteomic techniques for the detection and quantification of cytokines in melanoma research. Approaches covered span from mass spectrometry to immunoassays for single molecule detection (ELISA, western blot, multiplex assays (chemiluminescent, bead-based (Luminex and planar antibody arrays, ultrasensitive techniques (Singulex, Simoa, immuno-PCR, proximity ligation/extension assay, immunomagnetic reduction assay, to analyses of single cells producing cytokines (ELISpot, flow cytometry, mass cytometry and emerging techniques for single cell secretomics. Although this review is focused mainly on cancer and particularly melanoma, the discussed techniques are in general applicable to broad research field of biology and medicine, including stem cells, development, aging, immunology and intercellular communication.

Comparative evaluation of differential laser-induced perturbation spectroscopy as a technique to discriminate emerging skin pathology

Science.gov (United States)

Kozikowski, Raymond T.; Smith, Sarah E.; Lee, Jennifer A.; Castleman, William L.; Sorg, Brian S.; Hahn, David W.

2012-06-01

Fluorescence spectroscopy has been widely investigated as a technique for identifying pathological tissue; however, unrelated subject-to-subject variations in spectra complicate data analysis and interpretation. We describe and evaluate a new biosensing technique, differential laser-induced perturbation spectroscopy (DLIPS), based on deep ultraviolet (UV) photochemical perturbation in combination with difference spectroscopy. This technique combines sequential fluorescence probing (pre- and post-perturbation) with sub-ablative UV perturbation and difference spectroscopy to provide a new spectral dimension, facilitating two improvements over fluorescence spectroscopy. First, the differential technique eliminates significant variations in absolute fluorescence response within subject populations. Second, UV perturbations alter the extracellular matrix (ECM), directly coupling the DLIPS response to the biological structure. Improved biosensing with DLIPS is demonstrated in vivo in a murine model of chemically induced skin lesion development. Component loading analysis of the data indicates that the DLIPS technique couples to structural proteins in the ECM. Analysis of variance shows that DLIPS has a significant response to emerging pathology as opposed to other population differences. An optimal likelihood ratio classifier for the DLIPS dataset shows that this technique holds promise for improved diagnosis of epithelial pathology. Results further indicate that DLIPS may improve diagnosis of tissue by augmenting fluorescence spectra (i.e. orthogonal sensing).

An improved technique for quasi-static C-V measurements

International Nuclear Information System (INIS)

Turan, R.; Finstad, T.G.

1990-10-01

A new automated quasi-static C-V measurement technique for MOS capacitors has been developed. This techniques uses an integrating electrometer to measure the charge accumulated on a MOS capacitor in response of a small voltage step. Making use of the internal data storage system of a commercial electrometer and a personal computer, the charge Q on the MOS capacitor is measured as a function of time t and stored. The capacitance is then obtained by analyzing this Q-t data set. A Si MOS sample is measured and analyzed in terms of interface charges as an example. Advantages over a commercial quasi-static meter which uses similar measurement technique are presented. It is also shown that this technique is potentially capable of measuring both high and low frequency C-V curves simultaneously. 9 refs. 5 figs

Natural semantic networks in the Social Representations of Responsibility

Directory of Open Access Journals (Sweden)

Humberto Emilio Aguilera Arévalo

2010-07-01

Full Text Available The study of social representations of responsibility is a fundamental construct of the present democratic societies. Different empirical techniques such as natural semantic networks can significantly improve the approach to the object of study than the traditional associationist techniques. The present study examines natural semantic networks of six stimulus words with respect to responsibility and irresponsibility at the individual, in group and out group level in a sample of Guatemalan students.

Ethical considerations regarding the implementation of new technologies and techniques in surgery.

Science.gov (United States)

Strong, Vivian E; Forde, Kenneth A; MacFadyen, Bruce V; Mellinger, John D; Crookes, Peter F; Sillin, Lelan F; Shadduck, Phillip P

2014-08-01

Ethical considerations relevant to the implementation of new surgical technologies and techniques are explored and discussed in practical terms in this statement, including (1) How is the safety of a new technology or technique ensured?; (2) What are the timing and process by which a new technology or technique is implemented at a hospital?; (3) How are patients informed before undergoing a new technology or technique?; (4) How are surgeons trained and credentialed in a new technology or technique?; (5) How are the outcomes of a new technology or technique tracked and evaluated?; and (6) How are the responsibilities to individual patients and society at large balanced? The following discussion is presented with the intent to encourage thought and dialogue about ethical considerations relevant to the implementation of new technologies and new techniques in surgery.

Understanding Pupil Behaviour: Classroom Management Techniques for Teachers

Science.gov (United States)

Lewis, Ramon

2009-01-01

This book describes a system of successful classroom behaviour management techniques developed by the author over more than twenty-five years. It outlines the difficulties confronting teachers trying to manage pupils' misbehaviour in schools and describes four types of pupil who can be helped to behave responsibly. In "Understanding Pupil…

EVALUATION OF THE METERED-DOSE INHALER TECHNIQUE AMONG HEALTHCARE PROVIDERS

Directory of Open Access Journals (Sweden)

E. Nadi F. Zeraati

2005-07-01

Full Text Available Poor inhaler technique is a common problem both in asthmatic patients and healthcare providers, which contributes to poor asthma control. This study was performed to evaluate the adequacy of metered-dose inhaler (MDI technique in a sample of physicians and nurses practicing in hospitals of Hamadan University of Medical Sciences. A total of 173 healthcare providers voluntary participated in this study. After the participants answered a questionnaire aimed at identifying their involvement in MDI prescribing and counseling, a trained observer assessed their MDI technique using a checklist of nine steps. Of the 173 participants, 35 (20.2% were physicians and 138 (79.8% were nurses. Only 12 participants (6.93% performed all steps correctly. Physicians performed essential steps significantly better than nurses (85.7% vs. 63.8%, P < 0.05. The majority of healthcare providers responsible for instructing patients on the correct MDI technique were unable to perform this technique correctly, indicating the need for regular formal training programs on inhaler techniques.

Cogeneration techniques; Les techniques de cogeneration

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-10-01

This dossier about cogeneration techniques comprises 12 parts dealing successively with: the advantages of cogeneration (examples of installations, electrical and thermal efficiency); the combustion turbine (principle, performances, types); the alternative internal combustion engines (principle, types, rotation speed, comparative performances); the different configurations of cogeneration installations based on alternative engines and based on steam turbines (coal, heavy fuel and natural gas-fueled turbines); the environmental constraints of combustion turbines (pollutants, techniques of reduction of pollutant emissions); the environmental constraints of alternative internal combustion engines (gas and diesel engines); cogeneration and energy saving; the techniques of reduction of pollutant emissions (pollutants, unburnt hydrocarbons, primary and secondary (catalytic) techniques, post-combustion); the most-advanced configurations of cogeneration installations for enhanced performances (counter-pressure turbines, massive steam injection cycles, turbo-chargers); comparison between the performances of the different cogeneration techniques; the tri-generation technique (compression and absorption cycles). (J.S.)

Patch Clamp: A Powerful Technique for Studying the Mechanism of Acupuncture

Directory of Open Access Journals (Sweden)

D. Zhang

2012-01-01

Full Text Available Cellular and molecular events can be investigated using electrophysiological techniques. In particular, the patch-clamp method provides detailed information. In addition, the patch-clamp technique has become a powerful method for investigating the mechanisms underlying the effects of acupuncture. In this paper, recent researches on how acupuncture might modulate electrophysiological responses in the central nervous system (CNS and affect peripheral structures are reviewed.

The Limits of Corporate Social Responsibility: Techniques of Neutralization, Stakeholder Management and Political CSR.

Science.gov (United States)

Fooks, Gary; Gilmore, Anna; Collin, Jeff; Holden, Chris; Lee, Kelley

2013-01-01

Since scholarly interest in corporate social responsibility (CSR) has primarily focused on the synergies between social and economic performance, our understanding of how (and the conditions under which) companies use CSR to produce policy outcomes that work against public welfare has remained comparatively under-developed. In particular, little is known about how corporate decision-makers privately reconcile the conflicts between public and private interests, even though this is likely to be relevant to understanding the limitations of CSR as a means of aligning business activity with the broader public interest. This study addresses this issue using internal tobacco industry documents to explore British-American Tobacco's (BAT) thinking on CSR and its effects on the company's CSR Programme. The article presents a three-stage model of CSR development, based on Sykes and Matza's theory of techniques of neutralization, which links together: how BAT managers made sense of the company's declining political authority in the mid-1990s; how they subsequently justified the use of CSR as a tool of stakeholder management aimed at diffusing the political impact of public health advocates by breaking up political constituencies working towards evidence-based tobacco regulation; and how CSR works ideologically to shape stakeholders' perceptions of the relative merits of competing approaches to tobacco control. Our analysis has three implications for research and practice. First, it underlines the importance of approaching corporate managers' public comments on CSR critically and situating them in their economic, political and historical contexts. Second, it illustrates the importance of focusing on the political aims and effects of CSR. Third, by showing how CSR practices are used to stymie evidence-based government regulation, the article underlines the importance of highlighting and developing matrices to assess the negative social impacts of CSR.

Preconditioned conjugate gradient technique for the analysis of symmetric anisotropic structures

Science.gov (United States)

Noor, Ahmed K.; Peters, Jeanne M.

1987-01-01

An efficient preconditioned conjugate gradient (PCG) technique and a computational procedure are presented for the analysis of symmetric anisotropic structures. The technique is based on selecting the preconditioning matrix as the orthotropic part of the global stiffness matrix of the structure, with all the nonorthotropic terms set equal to zero. This particular choice of the preconditioning matrix results in reducing the size of the analysis model of the anisotropic structure to that of the corresponding orthotropic structure. The similarities between the proposed PCG technique and a reduction technique previously presented by the authors are identified and exploited to generate from the PCG technique direct measures for the sensitivity of the different response quantities to the nonorthotropic (anisotropic) material coefficients of the structure. The effectiveness of the PCG technique is demonstrated by means of a numerical example of an anisotropic cylindrical panel.

Communication methods and production techniques in fixed prosthesis fabrication: a UK based survey. Part 2: Production techniques

Science.gov (United States)

Berry, J.; Nesbit, M.; Saberi, S.; Petridis, H.

2014-01-01

Aim The aim of this study was to identify the communication methods and production techniques used by dentists and dental technicians for the fabrication of fixed prostheses within the UK from the dental technicians' perspective. This second paper reports on the production techniques utilised. Materials and methods Seven hundred and eighty-two online questionnaires were distributed to the Dental Laboratories Association membership and included a broad range of topics, such as demographics, impression disinfection and suitability, and various production techniques. Settings were managed in order to ensure anonymity of respondents. Statistical analysis was undertaken to test the influence of various demographic variables such as the source of information, the location, and the size of the dental laboratory. Results The number of completed responses totalled 248 (32% response rate). Ninety percent of the respondents were based in England and the majority of dental laboratories were categorised as small sized (working with up to 25 dentists). Concerns were raised regarding inadequate disinfection protocols between dentists and dental laboratories and the poor quality of master impressions. Full arch plastic trays were the most popular impression tray used by dentists in the fabrication of crowns (61%) and bridgework (68%). The majority (89%) of jaw registration records were considered inaccurate. Forty-four percent of dental laboratories preferred using semi-adjustable articulators. Axial and occlusal under-preparation of abutment teeth was reported as an issue in about 25% of cases. Base metal alloy was the most (52%) commonly used alloy material. Metal-ceramic crowns were the most popular choice for anterior (69%) and posterior (70%) cases. The various factors considered did not have any statistically significant effect on the answers provided. The only notable exception was the fact that more methods of communicating the size and shape of crowns were utilised for

A general technique for characterizing x-ray position sensitive arrays

International Nuclear Information System (INIS)

Dufresne, E.; Bruning, R.; Sutton, M.; Stephenson, G.B.

1994-03-01

We present a general statistical technique for characterizing x-ray sensitive linear diode arrays and CCD arrays. We apply this technique to characterize the response of a linear diode array, Princeton Instrument model X-PDA, and a virtual phase CCD array, TI 4849, to direct illumination by x-rays. We find that the response of the linear array is linearly proportional to the incident intensity and uniform over its length to within 2 %. Its quantum efficiency is 38 % for Cu K α x-rays. The resolution function is evaluated from the spatial autocorrelation function and falls to 10 % of its peak value after one pixel. On the other hand, the response of the CCD detecting system to direct x-ray exposure is non-linear. To properly quantify the scattered x-rays, one must correct for the non- linearity. The resolution is two pixels along the serial transfer direction. We characterize the noise of the CCD and propose a model that takes into account the non-linearity and the resolution function to estimate the quantum efficiency of the detector. The quantum efficiency is 20 %

Conditional truncated plurigaussian simulation; Simulacao plurigaussiana truncada com condicionamento

Energy Technology Data Exchange (ETDEWEB)

Simon, Vitor Hugo

1997-12-01

The goal of this work was a development of an algorithm for the Truncated Plurigaussian Stochastic Simulation and its validation in a complex geologic model. The reservoir data comes from Aux Vases Zone at Rural Hill Field in Illinois, USA, and from the 2D geological interpretation, described by WEIMER et al. (1982), three sets of samples, with different grid densities ware taken. These sets were used to condition the simulation and to refine the estimates of the non-stationary matrix of facies proportions, used to truncate the gaussian random functions (RF). The Truncated Plurigaussian Model is an extension of the Truncated Gaussian Model (TG). In this new model its possible to use several facies with different spatial structures, associated with the simplicity of TG. The geological interpretation, used as a validation model, was chosen because it shows a set of NW/SE elongated tidal channels cutting the NE/SW shoreline deposits interleaved by impermeable facies. These characteristics of spatial structures of sedimentary facies served to evaluate the simulation model. Two independent gaussian RF were used, as well as an 'erosive model' as the truncation strategy. Also, non-conditional simulations were proceeded, using linearly combined gaussian RF with varying correlation coefficients. It was analyzed the influence of some parameters like: number of gaussian RF,correlation coefficient, truncations strategy, in the outcome of simulation, and also the physical meaning of these parameters under a geological point of view. It was showed, step by step, using an example, the theoretical model, and how to construct an algorithm to simulate with the Truncated Plurigaussian Model. The conclusion of this work was that even with a plain algorithm of the Conditional Truncated Plurigaussian and a complex geological model it's possible to obtain a usefulness product. (author)

Early response of local steroid injection versus mini incision technique in treatment of carpal tunnel syndrome

International Nuclear Information System (INIS)

Awan, A.S.; Khan, A.; Afridi, S.A.; Khan, R.S.

2015-01-01

Carpal tunnel syndrome Carpal tunnel syndrome (CTS) is one of the commonest peripheral neuropathies which effects mainly middle aged women. Different techniques are being tried to decrease the post-operative pain in patients operated for CTS. The objective of this study was to compare effectiveness of local injection of steroid and mini incision technique in the treatment of carpal tunnel syndrome. Methods: This randomized control trial was conducted at department of Orthopedics and department of Neurosurgery, Ayub Teaching Hospital, Abbottabad from Aug 2011 to Feb 2013. A total of 116 patients of CTS were randomly allocated to either of the two groups. Fifty-eight Patient in Group A were subjected to local steroid injection and the same number of patient in Group B underwent mini incision technique. All patients of were advised to report to the OPD after one month to determine intervention effectiveness in terms of improvement in at least one grade of pain. Results: In this study mean age of the patients was 32.8 ± 5.1 years. Female gender was in dominance with 99 (86.3%) cases. In this study we compared the effectiveness of local steroid injection and mini incision technique in the treatment of carpel tunnel syndrome. We found out that the steroid injection was effective in 69.0% cases while mini incision technique was effective in 56.9% cases. The difference being statistically insignificant with a p-value of 0.17. Conclusion: The difference in pain after 1 month of the intervention was not statistically significant. (author)

The Delphi Technique: Making Sense of Consensus

Directory of Open Access Journals (Sweden)

Chia-Chien Hsu

2007-08-01

Full Text Available The Delphi technique is a widely used and accepted method for gathering data from respondents within their domain of expertise. The technique is designed as a group communication process which aims to achieve a convergence of opinion on a specific real-world issue. The Delphi process has been used in various fields of study such as program planning, needs assessment, policy determination, and resource utilization to develop a full range of alternatives, explore or expose underlying assumptions, as well as correlate judgments on a topic spanning a wide range of disciplines. The Delphi technique is well suited as a method for consensus-building by using a series of questionnaires delivered using multiple iterations to collect data from a panel of selected subjects. Subject selection, time frames for conducting and completing a study, the possibility of low response rates, and unintentionally guiding feedback from the respondent group are areas which should be considered when designing and implementing a Delphi study.

Structural Dynamic Response Compressing Technique in Bridges using a Cochlea-inspired Artificial Filter Bank (CAFB)

International Nuclear Information System (INIS)

Heo, G; Jeon, J; Son, B; Kim, C; Jeon, S; Lee, C

2016-01-01

In this study, a cochlea-inspired artificial filter bank (CAFB) was developed to efficiently obtain dynamic response of a structure, and a dynamic response measurement of a cable-stayed bridge model was also carried out to evaluate the performance of the developed CAFB. The developed CAFB used a band-pass filter optimizing algorithm (BOA) and peakpicking algorithm (PPA) to select and compress dynamic response signal containing the modal information which was significant enough. The CAFB was then optimized about the El-Centro earthquake wave which was often used in the construction research, and the software implementation of CAFB was finally embedded in the unified structural management system (USMS). For the evaluation of the developed CAFB, a real time dynamic response experiment was performed on a cable-stayed bridge model, and the response of the cable-stayed bridge model was measured using both the traditional wired system and the developed CAFB-based USMS. The experiment results showed that the compressed dynamic response acquired by the CAFB-based USMS matched significantly with that of the traditional wired system while still carrying sufficient modal information of the cable-stayed bridge. (paper)

Limitations caused by distortion in room impulse response measurements by swept sine technique

DEFF Research Database (Denmark)

Stojic, Branko; Ciric, Dejan; Markovic, Milos

2011-01-01

The significance of a room impulse response implies the requirement that its measurement should have a high level of accuracy in certain applications. One of the common problems in a measurement process is nonlinearity leading to the distortion of a room impulse response. Limitations caused...... domain with or without memory. On the other hand, the distortion in measurements is achieved either by applying the nonlinearity model or by using higher excitation level and a loudspeaker with a highly nonlinear characteristic. The results show that the most of distortion energy is located in the non...

Improvement of the detection response time of gas sensors using the association of artificial neural networks with pattern recognition technique; Amelioration de la reponse temporelle de capteurs de gaz par reconnaissance de forme a l'aide de reseaux de neurones

Energy Technology Data Exchange (ETDEWEB)

Bordieu, Ch.; Rebiere, D. [Bordeaux-1 Univ., Lab. IXL, UMR CNRS 5818, 33 (France); Pistre, J.; Planata, R. [Centre d' Etudes du Bouchet, 91 - Vert-le-Petit (France)

1999-07-01

The association of artificial neural networks (multilayer perceptrons) with a real time pattern recognition technique (shifting windows) allowed the development of systems for the detection and the quantification of gases. Shifting window technique is presented and offers an interesting way to improve the detection response time. The partial detector characterization with regard to its parameters was realized. Applications dealing with the detection of gas compounds using surface acoustic sensors permit to show the shifting window technique feasibility. (author)

A survey on OFDM channel estimation techniques based on denoising strategies

Directory of Open Access Journals (Sweden)

Pallaviram Sure

2017-04-01

Full Text Available Channel estimation forms the heart of any orthogonal frequency division multiplexing (OFDM based wireless communication receiver. Frequency domain pilot aided channel estimation techniques are either least squares (LS based or minimum mean square error (MMSE based. LS based techniques are computationally less complex. Unlike MMSE ones, they do not require a priori knowledge of channel statistics (KCS. However, the mean square error (MSE performance of the channel estimator incorporating MMSE based techniques is better compared to that obtained with the incorporation of LS based techniques. To enhance the MSE performance using LS based techniques, a variety of denoising strategies have been developed in the literature, which are applied on the LS estimated channel impulse response (CIR. The advantage of denoising threshold based LS techniques is that, they do not require KCS but still render near optimal MMSE performance similar to MMSE based techniques. In this paper, a detailed survey on various existing denoising strategies, with a comparative discussion of these strategies is presented.

Alcoholism and Self-Responsibility: The Gestalt Approach.

Science.gov (United States)

Graceffo, Samuel A.

1979-01-01

The Gestalt concept of self-responsibility is the acknowledgement by the individual that he/she is the author of all behavior. The behavior of the alcoholic is contrasted with the self-responsible individual. Clinical application of Gestalt therapy techniques to alcoholism is demonstrated and discussed with case illustrations. (Author)

Effectiveness of relaxation techniques before diagnostic screening of cancer patients

Directory of Open Access Journals (Sweden)

Montserrat Aiger

2016-07-01

Full Text Available Psychophysiological arousal was observed in cancer patients during the application of relaxation techniques prior to a diagnostic scan (PET-CT. The aim of the study is twofold: firstly, it is sought to establish whether such techniques can minimize patient arousal before diagnostic screening begins, and secondly to measure which of them are most effective. The dependent variable is electrodermal activity, recording the attentional level and emotional response, and the independent variable comprises the relaxation techniques used, namely Jacobson, breathing and visualization. The 39 patients were split into experimental groups to whom the relaxation techniques (Jacobson, breathing exercises, and visualization were applied before they went for the PET-CT. An activity-module procedure was applied to track electrodermal activity during the relaxation sessions, consisting of instructions, timeout; wait, task; relaxation and end of the recording session. The control group received no relaxation techniques before the PET-CT. Session-end results show that patients who perform relaxation techniques achieve greater attentional focus using Jacobson's technique (M = .212 and enhanced emotional containment using visualization (M = .206. It is concluded that relaxation techniques minimize the state of activation during the waiting period before a diagnostic scan.

Defect sizing using automated ultrasonic inspection techniques at RNL

International Nuclear Information System (INIS)

Rogerson, A.; Highmore, P.J.; Poulter, L.N.J.

1983-10-01

RNL has developed and applied automated wide-beam pulse-echo and time-of-flight techniques with synthetic aperture processing for sizing defects in clad thick-section weldments and nozzle corner regions. These techniques were amongst those used in the four test plate inspections making up the UKAEA Defect Detection Trials. In this report a critical appraisal is given of the sizing procedures adopted by RNL in these inspections. Several factors influencing sizing accuracy are discussed and results from particular defects highlighted. The time-of-flight technique with colour graphics data display is shown to be highly effective in imaging near-vertical buried defects and underclad defects of height greater than 5 mm. Early characterisation of any identified defect from its ultrasonic response under pulse-echo inspection is seen as a desirable aid to the selection of an appropriate advanced sizing technique for buried defects. (author)

Application of the Lorentz-transform technique to meson photoproduction

International Nuclear Information System (INIS)

Reiss, C.; Leidemann, W.; Orlandini, G.; Tomusiak, E.L.

2003-01-01

We show that the Lorentz integral transform (LIT) technique which has been successfully applied to photoreactions in light nuclei can also be applied to photoreactions involving particle production. A simple model where results are easily calculable in the traditional fashion is used to test the technique. Specifically, we compute inclusive π + photoproduction from deuterium for photon energies less than 200 MeV using a Yamaguchi model for the NN interaction. It is demonstrated that, although the response functions for inclusive meson production do not have favourable asymptotic behavior, one can nonetheless extract them by inversion of the transform. The implication is that one can treat realistic problems of photo-meson production, including all final-state interactions, by means of the LIT technique. (orig.)

Vessel size measurements in angiograms: A comparison of techniques

International Nuclear Information System (INIS)

Hoffmann, Kenneth R.; Nazareth, Daryl P.; Miskolczi, Laszlo; Gopal, Anant; Wang Zhou; Rudin, Stephen; Bednarek, Daniel R.

2002-01-01

As interventional procedures become more complicated, the need for accurate quantitative vascular information increases. In response to this need, many commercial vendors provide techniques for measurement of vessel sizes, usually based on derivative techniques. In this study, we investigate the accuracy of several techniques used in the measurement of vessel size. Simulated images of vessels having circular cross sections were generated and convolved with various focal spot distributions taking into account the magnification. These vessel images were then convolved with Gaussian image detector line spread functions (LSFs). Additionally, images of a phantom containing vessels with a range of diameters were acquired for the 4.5'', 6'', 9'', and 12'' modes of an image intensifier-TV (II-TV) system. Vessel sizes in the images were determined using a first-derivative technique, a second-derivative technique, a linear combination of these two measured sizes, a thresholding technique, a densitometric technique, and a model-based technique. For the same focal spot size, the shape of the focal spot distribution does not affect measured vessel sizes except at large magnifications. For vessels with diameters larger than the full-width-at-half-maximum (FWHM) of the LSF, accurate vessel sizes (errors ∼0.1 mm) could be obtained by using an average of sizes determined by the first and second derivatives. For vessels with diameters smaller than the FWHM of the LSF, the densitometric and model-based techniques can provide accurate vessel sizes when these techniques are properly calibrated

A new technique for generating spectrum compatible accelerogram

International Nuclear Information System (INIS)

Gosh, A.K.; Muralidharan, N.

1985-01-01

A new technique for generating spectrum compatible earthquake accelerogram is presented. Simplified linearised schemes are used to determine the weights of the modulated sinewaves used to represent the ground acceleration in conformity with the instants of time of attaining the maximum responses of the SDOFs. Some typical numerical results are presented in the paper. (orig.)

Time-lapse analysis of potential cellular responsiveness to Johrei, a Japanese healing technique

Directory of Open Access Journals (Sweden)

Moore Dan

2005-01-01

Full Text Available Abstract Background Johrei is an alternative healing practice which involves the channeling of a purported universal healing energy to influence the health of another person. Despite little evidence to support the efficacy of such practices the use of such treatments is on the rise. Methods We assessed cultured human cancer cells for potential responsiveness to Johrei treatment from a short distance. Johrei treatment was delivered by practitioners who participated in teams of two, alternating every half hour for a total of four hours of treatment. The practitioners followed a defined set of mental procedures to minimize variability in mental states between experiments. An environmental chamber maintained optimal growth conditions for cells throughout the experiments. Computerized time-lapse microscopy allowed documentation of cancer cell proliferation and cell death before, during and after Johrei treatments. Results Comparing eight control experiments with eight Johrei intervention experiments, we found no evidence of a reproducible cellular response to Johrei treatment. Conclusion Cell death and proliferation rates of cultured human cancer cells do not appear responsive to Johrei treatment from a short distance.

An application of the baseline correction technique for correcting distorted seismic acceleration time histories

International Nuclear Information System (INIS)

Lee, Gyu Mahn; Kim, Jong Wook; Jeoung, Kyeong Hoon; Kim, Tae Wan; Park, Keun Bae; Kim, Keung Koo

2008-03-01

Three kinds of baseline correction techniques named as 'Newmark', 'Zero-VD' and 'Newmark and Zero-VD' were introduced to correct the distorted physical characteristics of a seismic time history accelogram. The corrected seismic accelerations and distorted raw acceleration showed an identical response spectra in frequency domains, but showed various time history profiles in velocity and displacement domains. The referred correction techniques were programmed with UNIX-HP Fortran. The verification of the baseline corrected seismic data in terms of frequency response spectrum were performed by ANSYS of a commerical FEM software

On-line measurements of response time of temperature and pressure sensors in PWRs

International Nuclear Information System (INIS)

Hashemian, H.M.

2004-01-01

A review of modern techniques for in-situ response time testing of resistance temperature detectors (RTDs), and pressure, level and flow transmitters is presented. These techniques have been developed and validated for use in pressurized and boiling water reactors. The significance of the modern techniques is that they permit testing of installed sensors at process operating conditions and thereby provide the actual in-service response times of the sensors. (author)

Variable reflectivity signal mirrors and signal response measurements

International Nuclear Information System (INIS)

Vine, Glenn de; Shaddock, Daniel A; McClelland, David E

2002-01-01

Future gravitational wave detectors will include some form of signal mirror in order to alter the signal response of the device. We introduce interferometer configurations which utilize a variable reflectivity signal mirror allowing a tunable peak frequency and variable signal bandwidth. A detector configured with a Fabry-Perot cavity as the signal mirror is compared theoretically with one using a Michelson interferometer for a signal mirror. A system for the measurement of the interferometer signal responses is introduced. This technique is applied to a power-recycled Michelson interferometer with resonant sideband extraction. We present broadband measurements of the benchtop prototype's signal response for a range of signal cavity detunings. This technique is also applicable to most other gravitational wave detector configurations

Variable reflectivity signal mirrors and signal response measurements

CERN Document Server

Vine, G D; McClelland, D E

2002-01-01

Future gravitational wave detectors will include some form of signal mirror in order to alter the signal response of the device. We introduce interferometer configurations which utilize a variable reflectivity signal mirror allowing a tunable peak frequency and variable signal bandwidth. A detector configured with a Fabry-Perot cavity as the signal mirror is compared theoretically with one using a Michelson interferometer for a signal mirror. A system for the measurement of the interferometer signal responses is introduced. This technique is applied to a power-recycled Michelson interferometer with resonant sideband extraction. We present broadband measurements of the benchtop prototype's signal response for a range of signal cavity detunings. This technique is also applicable to most other gravitational wave detector configurations.

An improved autoradiographic technique for the detection of antibody-forming cells

International Nuclear Information System (INIS)

Mason, D.W.

1976-01-01

An autoradiographic technique for the detection of antibody-forming cells has been developed for the assay of anti-DNP responses. The lymphoid cell suspension to be assayed was allowed to sediment on to a glass slide coated with DNP-conjugated gelatin to which the secreted antibody bound during subsequent incubation. The bound antibody and its Ig class was revealed by a second incubation using 125 I-anti-immunoglobulin reagents followed by autoradiography. Studies on the sensitivity and specificity of the method are presented and its advantages over other techniques described. The technique should be readily applicable to other haptens

An on-road shock and vibration response test series utilizing worst case and statistical analysis techniques

International Nuclear Information System (INIS)

Cap, J.S.

1997-01-01

Defining the maximum expected shock and vibration responses for an on-road truck transportation environment is strongly dependent on the amount of response data that can be obtained. One common test scheme consists of measuring response data over a relatively short prescribed road course and then reviewing that data to obtain the maximum response levels. The more mathematically rigorous alternative is to collect an unbiased ensemble of response data during a long road trip. This paper compares data gathered both ways during a recent on-road certification test for a tractor trailer van being designed by Sandia

Endoluminal brachytherapy in the treatment of oesophageal cancer: technique description, case report and review of the literature

Directory of Open Access Journals (Sweden)

Luisa Castilla

2015-07-01

Full Text Available Endoesophageal brachytherapy is a useful technique for the palliative treatment of dysphagia in advanced oesophageal cancer. This technique offers good results on dysphagia control and quality of life. We report the case of a patient treated with this technique presenting complete response to the dysphagia. We describe endoesophageal brachyterapy technique and we comment on the literature.

Multi-modality imaging of tumor phenotype and response to therapy

Science.gov (United States)

Nyflot, Matthew J.

2011-12-01

Imaging and radiation oncology have historically been closely linked. However, the vast majority of techniques used in the clinic involve anatomical imaging. Biological imaging offers the potential for innovation in the areas of cancer diagnosis and staging, radiotherapy target definition, and treatment response assessment. Some relevant imaging techniques are FDG PET (for imaging cellular metabolism), FLT PET (proliferation), CuATSM PET (hypoxia), and contrast-enhanced CT (vasculature and perfusion). Here, a technique for quantitative spatial correlation of tumor phenotype is presented for FDG PET, FLT PET, and CuATSM PET images. Additionally, multimodality imaging of treatment response with FLT PET, CuATSM, and dynamic contrast-enhanced CT is presented, in a trial of patients receiving an antiangiogenic agent (Avastin) combined with cisplatin and radiotherapy. Results are also presented for translational applications in animal models, including quantitative assessment of proliferative response to cetuximab with FLT PET and quantification of vascular volume with a blood-pool contrast agent (Fenestra). These techniques have clear applications to radiobiological research and optimized treatment strategies, and may eventually be used for personalized therapy for patients.

Immunological consequences of using three different clinical/laboratory techniques of emulsifying peptide-based vaccines in incomplete Freund's adjuvant

Directory of Open Access Journals (Sweden)

Kast W Martin

2006-10-01

Full Text Available Abstract Incomplete Freund's adjuvant (IFA serves as a carrier for water-in-oil emulsion (W/O vaccines. The stability of such emulsions greatly affects vaccine safety and efficacy since continued presence of antigen depots at lymphoid organs releasing low-level antigens is known to stimulate a potent immune response and high-level systemic release of antigens can lead to tolerance. W/O emulsions for the purpose of clinical and laboratory peptide-based vaccinations have been prepared using the techniques of syringe extrusion, vortex or high-speed homogenization. There is no consensus in the field over which technique would be best to use and no immunological data are available that compare the three techniques. In this study, we compared the immune responses induced by a peptide-based vaccine prepared using vortex, syringe-extrusion and homogenization. The vaccination led to tumor rejection by mice vaccinated with the peptide-based vaccine prepared using all three techniques. The immunological data from the in vivo cytotoxicity assay showed a trend for lower responses and a higher variability and greater range in the immune responses induced by a vaccine that was emulsified by the vortex or homogenizer techniques as compared to the syringe-extrusion technique. There were statistically significant lower numbers of IFNγ-secreting cells induced when the mice were vaccinated with a peptide-based vaccine emulsion prepared using the vortex compared to the syringe-extrusion technique. At a suboptimal vaccine dose, the mice vaccinated with a peptide-based vaccine emulsion prepared using the vortex technique had the largest tumors compared to the syringe-extrusion or the homogenizer technique. In the setting of a busy pharmacy that prepares peptide-based vaccine emulsions for clinical studies, the vortex technique can still be used but we urge investigators to take special care in their choice of mixing vessels for the vortex technique as that can

Maximizing Reading Narrative Text Ability by Probing Prompting Learning Technique

Directory of Open Access Journals (Sweden)

Wiwied Pratiwi

2017-12-01

Full Text Available The objective of this research was to know whether Probing Prompting Learning Technique can be used to get the maximum effect of students’ reading narrative ability in teaching and learning process. This research was applied collaborative action reEsearch, this research was done in two cycle. The subject of this research was 23 students at tenth grade of SMA Kartikatama Metro. The result of the research showed that the Probing Prompting Learning Technique is useful and effective to help students get maximum effect of their reading. Based on the results of the questionnaire obtained an average percentage of 95%, it indicated that application of Probing Prompting Learning Technique in teaching l reading was appropriately applied. In short that students’ responses toward Probing Prompting Learning Technique in teaching reading was positive. In conclusion, Probing Prompting Learning Technique can get maximum effect of students’ reading ability. In relation to the result of the reserach, some suggestion are offered to english teacher, that  the use of Probing Prompting learning Technique in teaching reading will get the maximum effect of students’ reading abilty.

Lyoluminescence technique as an identification method for irradiated food stuffs

International Nuclear Information System (INIS)

Chazhoor, J.S.

1988-01-01

The paper presents the studies made on the suitability of lyoluminescence technique as an analytical method for the identification of irradiated food stuffs. Powder milk, cinnamon, cardamom, clove, red chilly, cocoa, pepper, tea, coffee, turmeric and coriander showed lyoluminescence response when irradiated by a 10 kGy 60 Co and dissolved in luminol solution. Various dosimetric parameters such as effect of storage time, proportionality of the lyoluminescence response to dose etc were studied. (author). 1 tab., 3 figs

A deconvolution technique for processing small intestinal transit data

Energy Technology Data Exchange (ETDEWEB)

Brinch, K. [Department of Clinical Physiology and Nuclear Medicine, Glostrup Hospital, University Hospital of Copenhagen (Denmark); Larsson, H.B.W. [Danish Research Center of Magnetic Resonance, Hvidovre Hospital, University Hospital of Copenhagen (Denmark); Madsen, J.L. [Department of Clinical Physiology and Nuclear Medicine, Hvidovre Hospital, University Hospital of Copenhagen (Denmark)

1999-03-01

The deconvolution technique can be used to compute small intestinal impulse response curves from scintigraphic data. Previously suggested approaches, however, are sensitive to noise from the data. We investigated whether deconvolution based on a new simple iterative convolving technique can be recommended. Eight healthy volunteers ingested a meal that contained indium-111 diethylene triamine penta-acetic acid labelled water and technetium-99m stannous colloid labelled omelette. Imaging was performed at 30-min intervals until all radioactivity was located in the colon. A Fermi function=(1+e{sup -{alpha}{beta}})/(1+e{sup (t-{alpha}){beta}}) was chosen to characterize the small intestinal impulse response function. By changing only two parameters, {alpha} and {beta}, it is possible to obtain configurations from nearly a square function to nearly a monoexponential function. Small intestinal input function was obtained from the gastric emptying curve and convolved with the Fermi function. The sum of least squares was used to find {alpha} and {beta} yielding the best fit of the convolved curve to the oberved small intestinal time-activity curve. Finally, a small intestinal mean transit time was calculated from the Fermi function referred to. In all cases, we found an excellent fit of the convolved curve to the observed small intestinal time-activity curve, that is the Fermi function reflected the small intestinal impulse response curve. Small intestinal mean transit time of liquid marker (median 2.02 h) was significantly shorter than that of solid marker (median 2.99 h; P<0.02). The iterative convolving technique seems to be an attractive alternative to ordinary approaches for the processing of small intestinal transit data. (orig.) With 2 figs., 13 refs.

Study on radiation-responsive epigenomes

International Nuclear Information System (INIS)

Kim, Jin Hong; Chung, Byung Yeop; Lee, Seung Sik; Moon, Yu Ran; Lee, Min Hee; Kim, Ji Hong

2011-01-01

The purpose of this project is development of world-class headspring techniques of biological science for application of plant genomes/epigenomes through study on radiation- responsive epigenomes and improvement of the national competitiveness in the field of fundamental technology for biological science and industry. Research scope includes 1) Investigation of radiation-responsive epigenomes and elucidation of their relation with phenotypes, 2) Elucidation of interaction and transcription control of epigenomes and epigenetic regulators using ionizing radiation (IR), 3) Investigation of epigenome-mediated traits in plant development, differentiation and antioxidant defense using IR, and 4) Development of application techniques of radiation-responsive epigenomes for eco-monitoring and molecular breeding. Main results are as follow: Setup of conditions for chromatin immunoprecipitation in irradiated plants: investigation of aberrations in DNA methylation after treatment with different IR: elucidation of responses of epigenetic regulators to gamma rays (GR): investigation of aberrations in GR-responsive epigenetic regulators at different developmental stages: elucidation of interactive aberrations of epigenomes and epigenetic regulators after treatment of GR: comparison of functional genomes after treatment of GR or H 2 O 2 : elucidation of relation of epigenomes with GR-induced delay in senescence: elucidation of relation of epigenomes with GR-induced aberrations in pigment metabolism: comparison of antioxidant defense in epigenetic mutants: investigation of senescence-associated changes in epigenomes: investigation of senescence-associated changes in epigenetic regulators: comparison of aberrations in epigenomes at different dose of GR for mutation

Study on radiation-responsive epigenomes

Energy Technology Data Exchange (ETDEWEB)

Kim, Jin Hong; Chung, Byung Yeop; Lee, Seung Sik; Moon, Yu Ran; Lee, Min Hee; Kim, Ji Hong [KAERI, Daejeon (Korea, Republic of)

2011-01-15

The purpose of this project is development of world-class headspring techniques of biological science for application of plant genomes/epigenomes through study on radiation- responsive epigenomes and improvement of the national competitiveness in the field of fundamental technology for biological science and industry. Research scope includes 1) Investigation of radiation-responsive epigenomes and elucidation of their relation with phenotypes, 2) Elucidation of interaction and transcription control of epigenomes and epigenetic regulators using ionizing radiation (IR), 3) Investigation of epigenome-mediated traits in plant development, differentiation and antioxidant defense using IR, and 4) Development of application techniques of radiation-responsive epigenomes for eco-monitoring and molecular breeding. Main results are as follow: Setup of conditions for chromatin immunoprecipitation in irradiated plants: investigation of aberrations in DNA methylation after treatment with different IR: elucidation of responses of epigenetic regulators to gamma rays (GR): investigation of aberrations in GR-responsive epigenetic regulators at different developmental stages: elucidation of interactive aberrations of epigenomes and epigenetic regulators after treatment of GR: comparison of functional genomes after treatment of GR or H{sub 2}O{sub 2}: elucidation of relation of epigenomes with GR-induced delay in senescence: elucidation of relation of epigenomes with GR-induced aberrations in pigment metabolism: comparison of antioxidant defense in epigenetic mutants: investigation of senescence-associated changes in epigenomes: investigation of senescence-associated changes in epigenetic regulators: comparison of aberrations in epigenomes at different dose of GR for mutation.

Com-scan techniques for material evaluation

International Nuclear Information System (INIS)

Jayakumar, T.K.; Naik, A.D.

1996-01-01

Presently a variety of products at various stages of production are being tested using NDT methods for ensuring their quality. The conventional NDT methods such as RT, UT, PT, MPT along with acoustic emission techniques are often employed for the purpose. However, the ever increasing demands for a comprehensive quality assurance of products necessitates newer avenues in testing methods to overcome certain inadequacies of conventional testing. This paper proposes Compton back-scatter technique as an additional alternative NDT tool for various measurements. When the radiation strikes material a small percentage of incident radiation scatters back with reduced energy. The back-scattered radiation is picked up by a digital backscatter gauge and analysed. The paper discusses experimental work carried out at the laboratory consisting of parameter evaluation, source detector geometry, back-scatter response for material, area effects, thickness and blockage measurements. The paper briefly discusses on-stream measurements carried out with the above experimental gauge. The paper deals with selection and comparison of measurements with those of ultrasonics. It also discusses the advantages of the radiation back-scatter testing. The paper recommends Com-scan back-scatter technique as a supplementary tool along with conventional testing. (author)

Application of the Sampling Selection Technique in Approaching Financial Audit

Directory of Open Access Journals (Sweden)

Victor Munteanu

2018-03-01

Full Text Available In his professional approach, the financial auditor has a wide range of working techniques, including selection techniques. They are applied depending on the nature of the information available to the financial auditor, the manner in which they are presented - paper or electronic format, and, last but not least, the time available. Several techniques are applied, successively or in parallel, to increase the safety of the expressed opinion and to provide the audit report with a solid basis of information. Sampling is used in the phase of control or clarification of the identified error. The main purpose is to corroborate or measure the degree of risk detected following a pertinent analysis. Since the auditor does not have time or means to thoroughly rebuild the information, the sampling technique can provide an effective response to the need for valorization.

Expressed satisfaction with the nominal group technique among change agents

NARCIS (Netherlands)

Gresham, J.N.

1986-01-01

Expressed Satisfaction with the Nominal Group Technique Among Change Agents. Jon Neal Gresham The purpose of this study was to determine whether or not policymakers and change agents with differing professional backgrounds and responsibilities, who participated in the structured process of a

Adaptive technique for matching the spectral response in skin lesions' images

International Nuclear Information System (INIS)

Pavlova, P; Borisova, E; Avramov, L; Pavlova, E

2015-01-01

The suggested technique is a subsequent stage for data obtaining from diffuse reflectance spectra and images of diseased tissue with a final aim of skin cancer diagnostics. Our previous work allows us to extract patterns for some types of skin cancer, as a ratio between spectra, obtained from healthy and diseased tissue in the range of 380 – 780 nm region. The authenticity of the patterns depends on the tested point into the area of lesion, and the resulting diagnose could also be fixed with some probability. In this work, two adaptations are implemented to localize pixels of the image lesion, where the reflectance spectrum corresponds to pattern. First adapts the standard to the personal patient and second – translates the spectrum white point basis to the relative white point of the image. Since the reflectance spectra and the image pixels are regarding to different white points, a correction of the compared colours is needed. The latest is done using a standard method for chromatic adaptation. The technique follows the steps below: –Calculation the colorimetric XYZ parameters for the initial white point, fixed by reflectance spectrum from healthy tissue; –Calculation the XYZ parameters for the distant white point on the base of image of nondiseased tissue; –Transformation the XYZ parameters for the test-spectrum by obtained matrix; –Finding the RGB values of the XYZ parameters for the test-spectrum according sRGB; Finally, the pixels of the lesion's image, corresponding to colour from the test-spectrum and particular diagnostic pattern are marked with a specific colour

Source-jerk analysis using a semi-explicit inverse kinetic technique

International Nuclear Information System (INIS)

Spriggs, G.D.; Pederson, R.A.

1985-01-01

A method is proposed for measuring the effective reproduction factor, k, in subcritical systems. The method uses the transient response of a subcritical system to the sudden removal of an extraneous neutron source (i.e., a source jerk). The response is analyzed using an inverse kinetic technique that least-squares fits the exact analytical solution corresponding to a source-jerk transient as derived from the point-reactor model. It has been found that the technique can provide an accurate means of measuring k in systems that are close to critical (i.e., 0.95 < k < 1.0). As a system becomes more subcritical (i.e., k << 1.0) spatial effects can introduce significant biases depending on the source and detector positions. However, methods are available that can correct for these biases and, hence, can allow measuring subcriticality in systems with k as low as 0.5. 12 refs., 3 figs

Source-jerk analysis using a semi-explicit inverse kinetic technique

International Nuclear Information System (INIS)

Spriggs, G.D.; Pederson, R.A.

1985-01-01

A method is proposed for measuring the effective reproduction factor, k, in subcritical systems. The method uses the transient responses of a subcritical system to the sudden removal of an extraneous neutron source (i.e., a source jerk). The response is analyzed using an inverse kinetic technique that least-squares fits the exact analytical solution corresponding to a source-jerk transient as derived from the point-reactor model. It has been found that the technique can provide an accurate means of measuring k in systems that are close to critical (i.e., 0.95 < k < 1.0). As a system becomes more subcritical (i.e., k << 1.0) spatial effects can introduce significant biases depending on the source and detector positions. However, methods are available that can correct for these biases and, hence, can allow measuring subcriticality in systems with k as low as 0.5

Ambient Response Analysis of the Heritage Court Tower Building Structure

DEFF Research Database (Denmark)

Brincker, Rune; Andersen, Palle

2000-01-01

In this paper an ambient response analysis of the Heritage Court Building structure is presented. The work is a part of a blind test organized by Professor Carlos Ventura, University of British Columbia. The response data were analyses using two different techniques: a non-parametric based on Fre...... modes, natural frequencies identified by the two techniques shoved good agreement, mode shape estimates were nearly identical, and damping ratios reasonably close and around 1-2% in the most cases....

Ambient Response Analysis of the Heritage Court Tower Building Structure

DEFF Research Database (Denmark)

Brincker, Rune; Andersen, Palle

2000-01-01

In this paper an ambient response analysis of the Heritage Court Building structure is presented. The work is a part of a blind test organized by Professor Carlos Ventura, University of British Columbia. The response data were analyses using two different techniques: a non-parametric based...... modes, natural frequencies identified by the two techniques shoved good agreement, mode shape estimates were nearly identical, and damping ratios reasonably close and around 1-2% in the most cases....

Exact solution of the optical response of thick slabs in the discrete dipole approach".

NARCIS (Netherlands)

Poppe, G.P.M.; Poppe, G.P.M.; Wijers, Christianus M.J.

1990-01-01

The recently developed double cell technique, which describes the optical response of an arbitrary semi-infinite dielectric crystal taking into account internal field effects, is extended to include the response of thick slabs. The surface sensitivity of the first technique is fully retained. The

Measurements techniques for transportation noise

International Nuclear Information System (INIS)

Brambilla, G.

2001-01-01

The noise from transport systems (roads, railways and aircraft) are increasing more and more both in space and in time and, therefore, they are still the major factor responsible for environmental noise pollution. The population exposed to transport noise is also increasing, and the corresponding health effects on people (i.e. annoyance and sleep disturbance) become more severe. Due to this current situation international and national legislation has been issued and implemented to reduce the harmful effects of such noise. This paper describes the techniques prescribed by recent Italian legislation to measure road, railway and aircraft noise. (author)

Applying of Reliability Techniques and Expert Systems in Management of Radioactive Accidents

International Nuclear Information System (INIS)

Aldaihan, S.; Alhbaib, A.; Alrushudi, S.; Karazaitri, C.

1998-01-01

Accidents including radioactive exposure have variety of nature and size. This makes such accidents complex situations to be handled by radiation protection agencies or any responsible authority. The situations becomes worse with introducing advanced technology with high complexity that provide operator huge information about system working on. This paper discusses the application of reliability techniques in radioactive risk management. Event tree technique from nuclear field is described as well as two other techniques from nonnuclear fields, Hazard and Operability and Quality Function Deployment. The objective is to show the importance and the applicability of these techniques in radiation risk management. Finally, Expert Systems in the field of accidents management are explored and classified upon their applications

Study on radiation-responsive epigenomes

Energy Technology Data Exchange (ETDEWEB)

Lee, Seung Sik; Lee, Seung Sik; Chung, Byung Yeoup; and others

2013-01-15

The purpose of this project is development of world-class head spring techniques of biological science for application of plant genomes/epigenomes through study on radiation-responsive epigenomes and improvement of the national competitiveness in the field of fundamental technology for biological science and industry. Research scope includes 1) Investigation of radiation-responsive epigenomes and elucidation of their relation with phenotypes, 2) Elucidation of interaction and transcription control of epigenomes and epigenetic regulators using IR, 3) Investigation of epigenome-mediated traits in plant development, differentiation and antioxidant defense using IR, and 4) Development of application techniques of radiation-responsive epigenomes for eco-monitoring and molecular breeding. Main results are as follow: investigation of the expression level of histone-modifying enzymes by IR; elucidation of the structural and functional changes of chaperone protein by IR; development of transgenic plant (DRD1-6); investigation of transcription control of epigenetic regulators by IR; investigation of relevance between DNA methylation and miRNA; comparison of gene expression in wild type and cmt mutant from Arabidopsis using gene chip; investigation control of epigenetic regulators in drd1-6 mutant by drought stress; development of transgenic plant using epigenetic regulators.

Study on radiation-responsive epigenomes

Energy Technology Data Exchange (ETDEWEB)

Kim, Jin Hong; Lee, Seung Sik; Bae, Hyung Woo; Kim, Ji Hong; Kim, Ji Eun; Cho, Eun Ju; Lee, Min Hee; Moon, Yu Ran [KAERI, Daejeon (Korea, Republic of)

2012-01-15

The purpose of this project is development of world-class headspring techniques of biological science for application of plant genomes/epigenomes through study on radiation- responsive epigenomes and improvement of the national competitiveness in the field of fundamental technology for biological science and industry. Research scope includes 1) Investigation of radiation-responsive epigenomes and elucidation of their relation with phenotypes, 2) Elucidation of interaction and transcription control of epigenomes and epigenetic regulators using IR, 3) Investigation of epigenome-mediated traits in plant development, differentiation and antioxidant defense using IR, and 4) Development of application techniques of radiation-responsive epigenomes for eco-monitoring and molecular breeding. Main results are as follow: practical application of ChIP in GR-treated Arabidopsis using anti-histone antibodies: mapping of DNA methylomes associated with GR-responsive transcriptomes: setup of methylated DNA quantification using HPLC: elucidation of aberrations in epigenetic regulation induced by low-dose GR using gamma phytotron: comparison of gene expression of histone-modifying enzymes after treatment of GR: elucidation of transcriptomes and physiological alterations associated with delayed senescence of drd1-6 mutant: comparison of gene expression of DNA methylation-related enzymes in GR-treated rice callus and Arabidopsis: investigation of germination capacity, low-temperature, salinity and drought stress-resistance in drd1-6 epigenetic mutant: investigation of aberrations in DNA methylation depending on dose rates of gamma radiation

Study on radiation-responsive epigenomes

International Nuclear Information System (INIS)

Kim, Jin Hong; Lee, Seung Sik; Bae, Hyung Woo; Kim, Ji Hong; Kim, Ji Eun; Cho, Eun Ju; Lee, Min Hee; Moon, Yu Ran

2012-01-01

The purpose of this project is development of world-class headspring techniques of biological science for application of plant genomes/epigenomes through study on radiation- responsive epigenomes and improvement of the national competitiveness in the field of fundamental technology for biological science and industry. Research scope includes 1) Investigation of radiation-responsive epigenomes and elucidation of their relation with phenotypes, 2) Elucidation of interaction and transcription control of epigenomes and epigenetic regulators using IR, 3) Investigation of epigenome-mediated traits in plant development, differentiation and antioxidant defense using IR, and 4) Development of application techniques of radiation-responsive epigenomes for eco-monitoring and molecular breeding. Main results are as follow: practical application of ChIP in GR-treated Arabidopsis using anti-histone antibodies: mapping of DNA methylomes associated with GR-responsive transcriptomes: setup of methylated DNA quantification using HPLC: elucidation of aberrations in epigenetic regulation induced by low-dose GR using gamma phytotron: comparison of gene expression of histone-modifying enzymes after treatment of GR: elucidation of transcriptomes and physiological alterations associated with delayed senescence of drd1-6 mutant: comparison of gene expression of DNA methylation-related enzymes in GR-treated rice callus and Arabidopsis: investigation of germination capacity, low-temperature, salinity and drought stress-resistance in drd1-6 epigenetic mutant: investigation of aberrations in DNA methylation depending on dose rates of gamma radiation

Study of a new glass matrix by the thermoluminescence technique

International Nuclear Information System (INIS)

Ferreira, Pamela Z.; Vedovato, Uly P.; Cunha, Diego M. da; Dantas, Noelio O.; Silva, Anielle C.A.; Neves, Lucio P.; Perini, Ana P.; Carrera, Betzabel N.S.; Watanabe, Shigueo

2015-01-01

The thermoluminescence technique is widely used for both personal and for high-dose dosimetry. In this work, the thermoluminescence technique was utilized to study a new glass matrix, with nominal composition of 20Li 2 CO 3 .10Al 2 O 3 .20BaO.50B 2 O 3 (mol%), irradiated with different doses in a 60 Co source. The glow curves and the dose-response curve were obtained for radiation doses between 50 Gy and 900 Gy. The results showed that this new glass matrix presents potential use in high-dose dosimetry. (author)

Impulse-response analysis of the market share attraction model

NARCIS (Netherlands)

D. Fok (Dennis); Ph.H.B.F. Franses (Philip Hans)

1999-01-01

textabstractWe propose a simulation-based technique to calculate impulse-response functions and their confidence intervals in a market share attraction model [MCI]. As an MCI model implies a reduced form model for the logs of relative market shares, simulation techniques have to be used to obtain

Modal Identification from Ambient Responses using Frequency Domain Decomposition

DEFF Research Database (Denmark)

Brincker, Rune; Zhang, L.; Andersen, P.

2000-01-01

In this paper a new frequency domain technique is introduced for the modal identification from ambient responses, ie. in the case where the modal parameters must be estimated without knowing the input exciting the system. By its user friendliness the technique is closely related to the classical ...

Study on production of useful metabolites by development of advanced cell culture techniques using radiation

Energy Technology Data Exchange (ETDEWEB)

Chung, Byung Yeoup; Kim, Jin Hong; Lee, Seung Sik; Kim, Jae Sung; An, Byung Chull; Moon, Yu Ran; Lee, Eun Mi; Lee, Min Hee; Lee, Jae Tack [KAERI, Daejeon (Korea, Republic of)

2010-02-15

The purpose of this project is improvement of investigation, materialization and evaluation techniques on effectiveness for functional natural compounds throughout development of tissue/cell culture techniques for mass production of useful metabolites using radiation. Research scope includes 1) Development of a technique for radiation tissue and cell culture, 2) Database construction for radiation response in plants and radiation effects, 3) Construction of general-purpose national based techniques of cell culture technique using radiation. Main results are as follow: mass culture of the adventitious roots of mountain ginseng (Panax ginseng C. A. Meyer) roots using rare earth elements in bioreactor: characterization of a transcription factor EoP gene from centipedegrass and the transcription regulation of LexA from Synechocystis sp PCC6803 and E. coli: identification of gamma-ray induced hydrogenase synthesis in hox gene transformed E. coli: transformation and the selection of the EoP transgene from Arabidopsis, rice and lettuce: Identification of the maysin and maysin derivatives in centipedegrass: characterization of gamma-ray induced color change in Taxus cuspidata: verification of the expression of antioxidant proteins (POD, APX and CAT) to gamma-ray in Arabidopsis: comparison of the response of the expression level to gamma-ray or H{sub 2}O{sub 2} in Arabidopsis; verification of the responses and effects to gamma-ray from plants (analysis of NPQ and ROS levels): the development method for rapidly enhancing maysin content of centipede grass; establishment of mass culture system for red beet

Study on production of useful metabolites by development of advanced cell culture techniques using radiation

International Nuclear Information System (INIS)

Chung, Byung Yeoup; Kim, Jin Hong; Lee, Seung Sik; Kim, Jae Sung; An, Byung Chull; Moon, Yu Ran; Lee, Eun Mi; Lee, Min Hee; Lee, Jae Tack

2010-02-01

The purpose of this project is improvement of investigation, materialization and evaluation techniques on effectiveness for functional natural compounds throughout development of tissue/cell culture techniques for mass production of useful metabolites using radiation. Research scope includes 1) Development of a technique for radiation tissue and cell culture, 2) Database construction for radiation response in plants and radiation effects, 3) Construction of general-purpose national based techniques of cell culture technique using radiation. Main results are as follow: mass culture of the adventitious roots of mountain ginseng (Panax ginseng C. A. Meyer) roots using rare earth elements in bioreactor: characterization of a transcription factor EoP gene from centipedegrass and the transcription regulation of LexA from Synechocystis sp PCC6803 and E. coli: identification of gamma-ray induced hydrogenase synthesis in hox gene transformed E. coli: transformation and the selection of the EoP transgene from Arabidopsis, rice and lettuce: Identification of the maysin and maysin derivatives in centipedegrass: characterization of gamma-ray induced color change in Taxus cuspidata: verification of the expression of antioxidant proteins (POD, APX and CAT) to gamma-ray in Arabidopsis: comparison of the response of the expression level to gamma-ray or H 2 O 2 in Arabidopsis; verification of the responses and effects to gamma-ray from plants (analysis of NPQ and ROS levels): the development method for rapidly enhancing maysin content of centipede grass; establishment of mass culture system for red beet

The use of indigenous techniques of communication for language learning: The case of Cameroon

OpenAIRE

Ebong, Balbina

2004-01-01

This study aimed at determining whether the use of indigenous techniques of communication can have a positive impact on the motivation of the learner of English as a foreign language in Cameroon. By indigenous techniques of communication we mean techniques like role-play, songs, the telling of folktales, riddles and proverbs. This work is intended as a contribution to the search for improvement of student motivation and enthusiasm, whereby they can be more responsive as they participate spont...

Development of techniques for monitoring corrosion in Magnox plant

International Nuclear Information System (INIS)

Haines, N.F.; Whittle, I.; Wilson, R.

1974-01-01

Steel oxidation in Magnox reactors has led to the development of techniques for measuring oxide thicknesses. An account is given of the methods used by the CEGB for making non-destructive measurements of oxide coatings both in the laboratory and remotely in the core regions of reactors. Specific techniques include β back-scattering which is compared with conventional microscope or weight gain methods for particular applications. The laser corrosion monitor and an ultrasonic method are described and compared as in-reactor techniques. An eddy current method is being developed for reactor regions where access is extremely restricted. A discussion considers the effect of oxide form upon the response of the instruments. The necessary further work is described which establishes the usefulness of each instrument over a range of oxide thicknesses and steels of different physical properties. (author)

Time series analysis of wind speed using VAR and the generalized impulse response technique

Energy Technology Data Exchange (ETDEWEB)

Ewing, Bradley T. [Area of Information Systems and Quantitative Sciences, Rawls College of Business and Wind Science and Engineering Research Center, Texas Tech University, Lubbock, TX 79409-2101 (United States); Kruse, Jamie Brown [Center for Natural Hazard Research, East Carolina University, Greenville, NC (United States); Schroeder, John L. [Department of Geosciences and Wind Science and Engineering Research Center, Texas Tech University, Lubbock, TX (United States); Smith, Douglas A. [Department of Civil Engineering and Wind Science and Engineering Research Center, Texas Tech University, Lubbock, TX (United States)

2007-03-15

This research examines the interdependence in time series wind speed data measured in the same location at four different heights. A multiple-equation system known as a vector autoregression is proposed for characterizing the time series dynamics of wind. Additionally, the recently developed method of generalized impulse response analysis provides insight into the cross-effects of the wind series and their responses to shocks. Findings are based on analysis of contemporaneous wind speed time histories taken at 13, 33, 70 and 160 ft above ground level with a sampling rate of 10 Hz. The results indicate that wind speeds measured at 70 ft was the most variable. Further, the turbulence persisted longer at the 70-ft measurement than at the other heights. The greatest interdependence is observed at 13 ft. Gusts at 160 ft led to the greatest persistence to an 'own' shock and led to greatest persistence in the responses of the other wind series. (author)

Dosimetric evaluation of the response of the TLD-100 dosemeters in the IMRT technique by 'Step and Shoot'; Evaluacion dosimetrica de la respuesta de los dosimetros TLD-100 en la tecnica de IMRT por 'Step and Shoot'

Energy Technology Data Exchange (ETDEWEB)

Vasquez, J. [Fundacion Clinica Valle del Lili, A.A. 020338, Cali (Colombia); Benavides, S.O. [Depto. de Fisica, Universidad del Valle, A.A. 25360, Cali (Colombia)

2005-07-01

We show the results of the dosimetry response of LiF thermoluminescent crystals: TLD-100, where they were radiated in a linear accelerator Siemens Primus Hl using the Intensity Modulated Radiation Therapy (IMRT) by step and shoot technique. Previous to the crystals calibration and response evaluation, the acceptation procedures recommended by the TG-53 protocol for validation of the technique were carried out. The planning system utilized was the Theraplan Plus 3.8, using the algorithm of Pencil Kernel. The register and verification system was Lantis 5.2. The response curve of dose versus charge was obtained from the readings of the TLD in a Harshaw 3500. The crystals were radiated in a Bench- Marck phantom with doses previously determined by using ionization chambers for square radiation fields, in a beam with a 0.68 TPR20,10 corresponding to 6 MV of energy. We compare the response of these through of radiation of segmented fields in a Anthropomorphic phantom and the calculated doses by the planning system. The results obtained in the crystals response show deviations less than 5 % between the measured dose and the calculated dose in the zones of low gradient. It allows its implementation like routine control of quality by IMRT. (Author)

Estimation of the Coefficient of Restitution of Rocking Systems by the Random Decrement Technique

DEFF Research Database (Denmark)

Brincker, Rune; Demosthenous, Milton; Manos, George C.

1994-01-01

The aim of this paper is to investigate the possibility of estimating an average damping parameter for a rocking system due to impact, the so-called coefficient of restitution, from the random response, i.e. when the loads are random and unknown, and the response is measured. The objective...... is to obtain an estimate of the free rocking response from the measured random response using the Random Decrement (RDD) Technique, and then estimate the coefficient of restitution from this free response estimate. In the paper this approach is investigated by simulating the response of a single degree...

Percutaneous aspiration biopsy in cervical spine lytic lesions. Indications and technique

Energy Technology Data Exchange (ETDEWEB)

Tampieri, D; Weill, A; Melanson, D; Ethier, R [Montreal Neurological Inst. and Hospital, PQ (Canada). Dept. of Neuroradiology

1991-02-01

We describe the technique and the results of the percutaneous aspiration biopsy (PAB) in a series of 9 patients presenting with neck pain and different degrees of myelopathy, in whom the cervical spine X-ray demonstrated lytic lesions of unknown origin. PAB is a useful, relatively safe technique, and leads to histological diagnosis between metastatic and inflammatory processes. Furthermore, in inflammatory lesions with negative hemoculture, PAB may help in detecting the micro-organism responsible and therefore allow a better antibiotic treatment. (orig.).

Embedded generation for industrial demand response in renewable energy markets

International Nuclear Information System (INIS)

Leanez, Frank J.; Drayton, Glenn

2010-01-01

Uncertainty in the electrical energy market is expected to increase with growth in the percentage of generation using renewable resources. Demand response can play a key role in giving stability to system operation. This paper discusses the embedded generation for industrial demand response in renewable energy markets. The methodology of the demand response is explained. It consists of long-term optimization and stochastic optimization. Wind energy, among all the renewable resources, is becoming increasingly popular. Volatility in the wind energy sector is high and this is explained using examples. Uncertainty in the wind market is shown using stochastic optimization. Alternative techniques for generation of wind energy were seen to be needed. Embedded generation techniques include co-generation (CHP) and pump storage among others. These techniques are analyzed and the results are presented. From these results, it is seen that investment in renewables is immediately required and that innovative generation technologies are also required over the long-term.

Generation of Quasi-Gaussian Pulses Based on Correlation Techniques

Directory of Open Access Journals (Sweden)

POHOATA, S.

2012-02-01

Full Text Available The Gaussian pulses have been mostly used within communications, where some applications can be emphasized: mobile telephony (GSM, where GMSK signals are used, as well as the UWB communications, where short-period pulses based on Gaussian waveform are generated. Since the Gaussian function signifies a theoretical concept, which cannot be accomplished from the physical point of view, this should be expressed by using various functions, able to determine physical implementations. New techniques of generating the Gaussian pulse responses of good precision are approached, proposed and researched in this paper. The second and third order derivatives with regard to the Gaussian pulse response are accurately generated. The third order derivates is composed of four individual rectangular pulses of fixed amplitudes, being easily to be generated by standard techniques. In order to generate pulses able to satisfy the spectral mask requirements, an adequate filter is necessary to be applied. This paper emphasizes a comparative analysis based on the relative error and the energy spectra of the proposed pulses.

Simulation error propagation for a dynamic rod worth measurement technique

International Nuclear Information System (INIS)

Kastanya, D.F.; Turinsky, P.J.

1996-01-01

KRSKO nuclear station, subsequently adapted by Westinghouse, introduced the dynamic rod worth measurement (DRWM) technique for measuring pressurized water reactor rod worths. This technique has the potential for reduced test time and primary loop waste water versus alternatives. The measurement is performed starting from a slightly supercritical state with all rods out (ARO), driving a bank in at the maximum stepping rate, and recording the ex-core detectors responses and bank position as a function of time. The static bank worth is obtained by (1) using the ex-core detectors' responses to obtain the core average flux (2) using the core average flux in the inverse point-kinetics equations to obtain the dynamic bank worth (3) converting the dynamic bank worth to the static bank worth. In this data interpretation process, various calculated quantities obtained from a core simulator are utilized. This paper presents an analysis of the sensitivity to the impact of core simulator errors on the deduced static bank worth

Agricultural Soil Spectral Response and Properties Assessment: Effects of Measurement Protocol and Data Mining Technique

Directory of Open Access Journals (Sweden)

Asa Gholizadeh

2017-10-01

Full Text Available Soil spectroscopy has shown to be a fast, cost-effective, environmentally friendly, non-destructive, reproducible and repeatable analytical technique. Soil components, as well as types of instruments, protocols, sampling methods, sample preparation, spectral acquisition techniques and analytical algorithms have a combined influence on the final performance. Therefore, it is important to characterize these differences and to introduce an effective approach in order to minimize the technical factors that alter reflectance spectra and consequent prediction. To quantify this alteration, a joint project between Czech University of Life Sciences Prague (CULS and Tel-Aviv University (TAU was conducted to estimate Cox, pH-H2O, pH-KCl and selected forms of Fe and Mn. Two different soil spectral measurement protocols and two data mining techniques were used to examine seventy-eight soil samples from five agricultural areas in different parts of the Czech Republic. Spectral measurements at both laboratories were made using different ASD spectroradiometers. The CULS protocol was based on employing a contact probe (CP spectral measurement scheme, while the TAU protocol was carried out using a CP measurement method, accompanied with the internal soil standard (ISS procedure. Two spectral datasets, acquired from different protocols, were both analyzed using partial least square regression (PLSR technique as well as the PARACUDA II®, a new data mining engine for optimizing PLSR models. The results showed that spectra based on the CULS setup (non-ISS demonstrated significantly higher albedo intensity and reflectance values relative to the TAU setup with ISS. However, the majority of statistics using the TAU protocol was not noticeably better than the CULS spectra. The paper also highlighted that under both measurement protocols, the PARACUDA II® engine proved to be a powerful tool for providing better results than PLSR. Such initiative is not only a way to

Modal Identification from Ambient Responses Using Frequency Domain Decomposition

DEFF Research Database (Denmark)

Brincker, Rune; Zhang, Lingmi; Andersen, Palle

2000-01-01

In this paper a new frequency domain technique is introduced for the modal identification from ambient responses, i.e. in the case where the modal parameters must be estimated without knowing the input exciting the system. By its user friendliness the technique is closely related to the classical...

Lectin typing of Campylobacter jejuni using a novel quartz crystal microbalance technique

Energy Technology Data Exchange (ETDEWEB)

Yakovleva, Maria E., E-mail: maria.yakovleva@gmail.com [Department of Infectious Diseases and Medical Microbiology, Lund University, 223 62 Lund (Sweden); Moran, Anthony P. [Department of Microbiology, School of Natural Sciences, National University of Ireland, Galway (Ireland); Safina, Gulnara R. [Department of Analytical and Marine Chemistry, University of Gothenburg, 412 96 Gothenburg (Sweden); Wadstroem, Torkel [Department of Infectious Diseases and Medical Microbiology, Lund University, 223 62 Lund (Sweden); Danielsson, Bengt [Acromed Invest AB, Magistratsvaegen 10, 226 43 Lund (Sweden)

2011-05-23

Seven Campylobacter jejuni strains were characterised by a lectin typing assay. The typing system was based on a quartz crystal microbalance technique (QCM) with four commercially available lectins (wheat germ agglutinin, Maackia amurensis lectin, Lens culinaris agglutinin, and Concanavalin A), which were chosen for their differing carbohydrate specificities. Initially, the gold surfaces of the quartz crystals were modified with 11-mercaptoundecanoic acid followed by lectin immobilisation using a conventional amine-coupling technique. Bacterial cells were applied for lectin typing without preliminary treatment, and resonant frequency and dissipation responses were recorded. The adhesion of microorganisms on lectin surfaces was confirmed by atomic force microscopy. Scanning was performed in the tapping mode and the presence of bacteria on lectin-coated surfaces was successfully demonstrated. A significant difference in the dissipation response was observed for different C. jejuni strains which made it possible to use this parameter for discriminating between bacterial strains. In summary, the QCM technique proved a powerful tool for the recognition and discrimination of C. jejuni strains. The approach may also prove applicable to strain discrimination of other bacterial species, particularly pathogens.

Lectin typing of Campylobacter jejuni using a novel quartz crystal microbalance technique

International Nuclear Information System (INIS)

Yakovleva, Maria E.; Moran, Anthony P.; Safina, Gulnara R.; Wadstroem, Torkel; Danielsson, Bengt

2011-01-01

Seven Campylobacter jejuni strains were characterised by a lectin typing assay. The typing system was based on a quartz crystal microbalance technique (QCM) with four commercially available lectins (wheat germ agglutinin, Maackia amurensis lectin, Lens culinaris agglutinin, and Concanavalin A), which were chosen for their differing carbohydrate specificities. Initially, the gold surfaces of the quartz crystals were modified with 11-mercaptoundecanoic acid followed by lectin immobilisation using a conventional amine-coupling technique. Bacterial cells were applied for lectin typing without preliminary treatment, and resonant frequency and dissipation responses were recorded. The adhesion of microorganisms on lectin surfaces was confirmed by atomic force microscopy. Scanning was performed in the tapping mode and the presence of bacteria on lectin-coated surfaces was successfully demonstrated. A significant difference in the dissipation response was observed for different C. jejuni strains which made it possible to use this parameter for discriminating between bacterial strains. In summary, the QCM technique proved a powerful tool for the recognition and discrimination of C. jejuni strains. The approach may also prove applicable to strain discrimination of other bacterial species, particularly pathogens.

Satellite SAR interferometric techniques applied to emergency mapping

Science.gov (United States)

Stefanova Vassileva, Magdalena; Riccardi, Paolo; Lecci, Daniele; Giulio Tonolo, Fabio; Boccardo Boccardo, Piero; Chiesa, Giuliana; Angeluccetti, Irene

2017-04-01

This paper aim to investigate the capabilities of the currently available SAR interferometric algorithms in the field of emergency mapping. Several tests have been performed exploiting the Copernicus Sentinel-1 data using the COTS software ENVI/SARscape 5.3. Emergency Mapping can be defined as "creation of maps, geo-information products and spatial analyses dedicated to providing situational awareness emergency management and immediate crisis information for response by means of extraction of reference (pre-event) and crisis (post-event) geographic information/data from satellite or aerial imagery". The conventional differential SAR interferometric technique (DInSAR) and the two currently available multi-temporal SAR interferometric approaches, i.e. Permanent Scatterer Interferometry (PSI) and Small BAseline Subset (SBAS), have been applied to provide crisis information useful for the emergency management activities. Depending on the considered Emergency Management phase, it may be distinguished between rapid mapping, i.e. fast provision of geospatial data regarding the area affected for the immediate emergency response, and monitoring mapping, i.e. detection of phenomena for risk prevention and mitigation activities. In order to evaluate the potential and limitations of the aforementioned SAR interferometric approaches for the specific rapid and monitoring mapping application, five main factors have been taken into account: crisis information extracted, input data required, processing time and expected accuracy. The results highlight that DInSAR has the capacity to delineate areas affected by large and sudden deformations and fulfills most of the immediate response requirements. The main limiting factor of interferometry is the availability of suitable SAR acquisition immediately after the event (e.g. Sentinel-1 mission characterized by 6-day revisiting time may not always satisfy the immediate emergency request). PSI and SBAS techniques are suitable to produce

A note on determination of the diffuse-field sensitivity of microphones using the reciprocity technique

DEFF Research Database (Denmark)

Barrera Figueroa, Salvador; Jacobsen, Finn

2008-01-01

angles of incidence but also on the accuracy of the frequency response at normal incidence. By contrast, this paper is concerned with determining the absolute diffuse-field response of a microphone using the reciprocity technique. To examine this possibility, a reciprocity calibration setup is used...

Standardization of the Fricke gel dosimetry method and tridimensional dose evaluation using the magnetic resonance imaging technique

International Nuclear Information System (INIS)

Cavinato, Christianne Cobello

2009-01-01

This study standardized the method for obtaining the Fricke gel solution developed at IPEN. The results for different gel qualities used in the preparation of solutions and the influence of the gelatin concentration in the response of dosimetric solutions were compared. Type tests such as: dose response dependence, minimum and maximum detection limits, response reproducibility, among others, were carried out using different radiation types and the Optical Absorption (OA) spectrophotometry and Magnetic Resonance (MR) techniques. The useful dose ranges for Co 60 gamma radiation and 6 MeV photons are 0,4 to 30,0 Gy and 0,5 to 100,0 Gy , using OA and MR techniques, respectively. A study of ferric ions diffusion in solution was performed to determine the optimum time interval between irradiation and samples evaluation; until 2,5 hours after irradiation to obtain sharp MR images. A spherical simulator consisting of Fricke gel solution prepared with 5% by weight 270 Bloom gelatine (national quality) was developed to be used to three-dimensional dose assessment using the Magnetic Resonance Imaging (MRI) technique. The Fricke gel solution prepared with 270 Bloom gelatine, that, in addition to low cost, can be easily acquired on the national market, presents satisfactory results on the ease of handling, sensitivity, response reproducibility and consistency. The results confirm their applicability in the three-dimensional dosimetry using MRI technique. (author)

Estimation of single plane unbalance parameters of a rotor-bearing system using Kalman filtering based force estimation technique

Science.gov (United States)

Shrivastava, Akash; Mohanty, A. R.

2018-03-01

This paper proposes a model-based method to estimate single plane unbalance parameters (amplitude and phase angle) in a rotor using Kalman filter and recursive least square based input force estimation technique. Kalman filter based input force estimation technique requires state-space model and response measurements. A modified system equivalent reduction expansion process (SEREP) technique is employed to obtain a reduced-order model of the rotor system so that limited response measurements can be used. The method is demonstrated using numerical simulations on a rotor-disk-bearing system. Results are presented for different measurement sets including displacement, velocity, and rotational response. Effects of measurement noise level, filter parameters (process noise covariance and forgetting factor), and modeling error are also presented and it is observed that the unbalance parameter estimation is robust with respect to measurement noise.

Studies on humoral and cellular immune responses in filariasis: Use of nuclear techniques

International Nuclear Information System (INIS)

Subrahmanyam, D.; Chaudhuri, S.

1975-01-01

Immunologic studies in filariasis have been concentrated on areas such as (a) isolation of a specific antigen(s) for early diagnosis of the disease, (b) host-parasite relation in the infection and (c) factors involved in inducing resistance to the infection. The paper discusses information obtained on these aspects with experimental filariasis and its possible implications for the human disease. Areas of research where nuclear techniques could contribute further to a greater understanding of the immunology of filariasis are also indicated. (author)

Comparison of first dimension IPG and NEPHGE techniques in two-dimensional gel electrophoresis experiment with cytosolic unfolded protein response in Saccharomyces cerevisiae

Science.gov (United States)

2013-01-01

Background Two-dimensional gel electrophoresis (2DE) is one of the most popular methods in proteomics. Currently, most 2DE experiments are performed using immobilized pH gradient (IPG) in the first dimension; however, some laboratories still use carrier ampholytes-based isoelectric focusing technique. The aim of this study was to directly compare IPG-based and non-equilibrium pH gradient electrophoresis (NEPHGE)-based 2DE techniques by using the same samples and identical second dimension procedures. We have used commercially available Invitrogen ZOOM IPGRunner and WITAvision systems for IPG and NEPHGE, respectively. The effectiveness of IPG-based and NEPHGE-based 2DE methods was compared by analysing differential protein expression during cytosolic unfolded protein response (UPR-Cyto) in Saccharomyces cerevisiae. Results Protein loss during 2DE procedure was higher in IPG-based method, especially for basic (pI > 7) proteins. Overall reproducibility of spots was slightly better in NEPHGE-based method; however, there was a marked difference when evaluating basic and acidic protein spots. Using Coomassie staining, about half of detected basic protein spots were not reproducible by IPG-based 2DE, whereas NEPHGE-based method showed excellent reproducibility in the basic gel zone. The reproducibility of acidic proteins was similar in both methods. Absolute and relative volume variability of separate protein spots was comparable in both 2DE techniques. Regarding proteomic analysis of UPR-Cyto, the results exemplified parameters of general comparison of the methods. New highly basic protein Sis1p, overexpressed during UPR-Cyto stress, was identified by NEPHGE-based 2DE method, whereas IPG-based method showed unreliable results in the basic pI range and did not provide any new information on basic UPR-Cyto proteins. In the acidic range, the main UPR-Cyto proteins were detected and quantified by both methods. The drawback of NEPHGE-based 2DE method is its failure to

Detection of cavitation vortex in hydraulic turbines using acoustic techniques

International Nuclear Information System (INIS)

Candel, I; Ioana, C; Bunea, F; Politehnica University of Bucharest (Romania))" data-affiliation=" (Power Engineering Faculty, Politehnica University of Bucharest (Romania))" >Dunca, G; Politehnica University of Bucharest (Romania))" data-affiliation=" (Power Engineering Faculty, Politehnica University of Bucharest (Romania))" >Bucur, D M; Division Technique Générale, Grenoble (France))" data-affiliation=" (Electricité de France, Division Technique Générale, Grenoble (France))" >Reeb, B; Ciocan, G D

2014-01-01

Cavitation phenomena are known for their destructive capacity in hydraulic machineries and are caused by the pressure decrease followed by an implosion when the cavitation bubbles find an adverse pressure gradient. A helical vortex appears in the turbine diffuser cone at partial flow rate operation and can be cavitating in its core. Cavity volumes and vortex frequencies vary with the under-pressure level. If the vortex frequency comes close to one of the eigen frequencies of the turbine, a resonance phenomenon may occur, the unsteady fluctuations can be amplified and lead to important turbine and hydraulic circuit damage. Conventional cavitation vortex detection techniques are based on passive devices (pressure sensors or accelerometers). Limited sensor bandwidths and low frequency response limit the vortex detection and characterization information provided by the passive techniques. In order to go beyond these techniques and develop a new active one that will remove these drawbacks, previous work in the field has shown that techniques based on acoustic signals using adapted signal content to a particular hydraulic situation, can be more robust and accurate. The cavitation vortex effects in the water flow profile downstream hydraulic turbines runner are responsible for signal content modifications. Basic signal techniques use narrow band signals traveling inside the flow from an emitting transducer to a receiving one (active sensors). Emissions of wide band signals in the flow during the apparition and development of the vortex embeds changes in the received signals. Signal processing methods are used to estimate the cavitation apparition and evolution. Tests done in a reduced scale facility showed that due to the increasing flow rate, the signal -- vortex interaction is seen as modifications on the received signal's high order statistics and bandwidth. Wide band acoustic transducers have a higher dynamic range over mechanical elements; the system

Study on Production of Useful Metabolites by Development of Advanced Cell Culture Techniques Using Radiation

Energy Technology Data Exchange (ETDEWEB)

Chung, Byung Yeoup; Kim, J. H.; Lee, S. S.; Shyamkumar, B.; An, B. C.; Moon, Y. R.; Lee, E. M.; Lee, M. H.

2009-02-15

The purpose of this project is improvement of investigation, materialization and evaluation techniques on effectiveness for functional natural compounds throughout development of tissue/cell culture techniques for mass production of useful metabolites using radiation. Research scope includes 1) Development of a technique for radiation tissue and cell culture, 2) Database construction for radiation response in plants and radiation effects, 3) Construction of general-purpose national based techniques of cell culture technique using radiation. Main results are as follow: Establishment of a tissue culture system (Rubus sp., Lithospermum erythrorhizon, and Rhodiola rosea); characterization of radiation activated gene expression from cultivated bokbunja (Rubus sp.) and Synechocystis sp., identification of gamma-ray induced color change in plants; identification of sensitivity to gamma-ray from Omija (Schisandra chinensis) extract; identification of the response of thylakoid proteins to gamma-ray in spinach and Arabidopsis; identification of gamma-ray induced gene relating to pigment metabolism; characterization of different NPQ changes to gamma-irradiated plants; verification of the effects of rare earth element including anti-bacterial and anti-fungal properties and as a growth enhancer; identification of changes in the growth of gamma-irradiated Synechocystis; and investigation of liquid cell culture conditions from Rhodiola rosea

Study on Production of Useful Metabolites by Development of Advanced Cell Culture Techniques Using Radiation

International Nuclear Information System (INIS)

Chung, Byung Yeoup; Kim, J. H.; Lee, S. S.; Shyamkumar, B.; An, B. C.; Moon, Y. R.; Lee, E. M.; Lee, M. H.

2009-02-01

The purpose of this project is improvement of investigation, materialization and evaluation techniques on effectiveness for functional natural compounds throughout development of tissue/cell culture techniques for mass production of useful metabolites using radiation. Research scope includes 1) Development of a technique for radiation tissue and cell culture, 2) Database construction for radiation response in plants and radiation effects, 3) Construction of general-purpose national based techniques of cell culture technique using radiation. Main results are as follow: Establishment of a tissue culture system (Rubus sp., Lithospermum erythrorhizon, and Rhodiola rosea); characterization of radiation activated gene expression from cultivated bokbunja (Rubus sp.) and Synechocystis sp., identification of gamma-ray induced color change in plants; identification of sensitivity to gamma-ray from Omija (Schisandra chinensis) extract; identification of the response of thylakoid proteins to gamma-ray in spinach and Arabidopsis; identification of gamma-ray induced gene relating to pigment metabolism; characterization of different NPQ changes to gamma-irradiated plants; verification of the effects of rare earth element including anti-bacterial and anti-fungal properties and as a growth enhancer; identification of changes in the growth of gamma-irradiated Synechocystis; and investigation of liquid cell culture conditions from Rhodiola rosea

Techniques to assess acoustic-structure interaction in liquid rocket engines

Science.gov (United States)

Davis, R. Benjamin

Acoustoelasticity is the study of the dynamic interaction between elastic structures and acoustic enclosures. In this dissertation, acoustoelasticity is considered in the context of liquid rocket engine design. The techniques presented here can be used to determine which forcing frequencies are important in acoustoelastic systems. With a knowledge of these frequencies, an analyst can either find ways to attenuate the excitation at these frequencies or alter the system in such a way that the prescribed excitations do result in a resonant condition. The end result is a structural component that is less susceptible to failure. The research scope is divided into three parts. In the first part, the dynamics of cylindrical shells submerged in liquid hydrogen (LH2) and liquid oxygen (LOX) are considered. The shells are bounded by rigid outer cylinders. This configuration gives rise to two fluid-filled cavities---an inner cylindrical cavity and an outer annular cavity. Such geometries are common in rocket engine design. The natural frequencies and modes of the fluid-structure system are computed by combining the rigid wall acoustic cavity modes and the in vacuo structural modes into a system of coupled ordinary differential equations. Eigenvalue veering is observed near the intersections of the curves representing natural frequencies of the rigid wall acoustic and the in vacuo structural modes. In the case of a shell submerged in LH2, system frequencies near these intersections are as much as 30% lower than the corresponding in vacuo structural frequencies. Due to its high density, the frequency reductions in the presence of LOX are even more dramatic. The forced responses of a shell submerged in LH2 and LOX while subject to a harmonic point excitation are also presented. The responses in the presence of fluid are found to be quite distinct from those of the structure in vacuo. In the second part, coupled mode theory is used to explore the fundamental features of

Optimum cycle frequencies in hand-rim wheelchair propulsion. Wheelchair propulsion technique

NARCIS (Netherlands)

van der Woude, L H; Veeger, DirkJan (H. E. J.); Rozendal, R H; Sargeant, A J

1989-01-01

To study the effect of different cycle frequencies on cardio-respiratory responses and propulsion technique in hand-rim wheelchair propulsion, experienced wheelchair sportsmen (WS group; n = 6) and non-wheelchair users (NW group; n = 6) performed wheelchair exercise tests on a motor-driven

Comparison of Calibration Techniques for Low-Cost Air Quality Monitoring

Science.gov (United States)

Malings, C.; Ramachandran, S.; Tanzer, R.; Kumar, S. P. N.; Hauryliuk, A.; Zimmerman, N.; Presto, A. A.

2017-12-01

Assessing the intra-city spatial distribution and temporal variability of air quality can be facilitated by a dense network of monitoring stations. However, the cost of implementing such a network can be prohibitive if high-quality but high-cost monitoring systems are used. To this end, the Real-time Affordable Multi-Pollutant (RAMP) sensor package has been developed at the Center for Atmospheric Particle Studies of Carnegie Mellon University, in collaboration with SenSevere LLC. This self-contained unit can measure up to five gases out of CO, SO2, NO, NO2, O3, VOCs, and CO2, along with temperature and relative humidity. Responses of individual gas sensors can vary greatly even when exposed to the same ambient conditions. Those of VOC sensors in particular were observed to vary by a factor-of-8, which suggests that each sensor requires its own calibration model. To this end, we apply and compare two different calibration methods to data collected by RAMP sensors collocated with a reference monitor station. The first method, random forest (RF) modeling, is a rule-based method which maps sensor responses to pollutant concentrations by implementing a trained sequence of decision rules. RF modeling has previously been used for other RAMP gas sensors by the group, and has produced precise calibrated measurements. However, RF models can only predict pollutant concentrations within the range observed in the training data collected during the collocation period. The second method, Gaussian process (GP) modeling, is a probabilistic Bayesian technique whereby broad prior estimates of pollutant concentrations are updated using sensor responses to generate more refined posterior predictions, as well as allowing predictions beyond the range of the training data. The accuracy and precision of these techniques are assessed and compared on VOC data collected during the summer of 2017 in Pittsburgh, PA. By combining pollutant data gathered by each RAMP sensor and applying

Electromagnetically induced acoustic emission—novel NDT technique for damage evaluation

Science.gov (United States)

Finkel, P.; Godinez, V.; Miller, R.; Finlayson, R.

2001-04-01

A recently developed electromagnetically induced acoustic emission technique (EM AE) which can be used for damage assessment of thin walled conducting structures is described. This technique allows a structure to be loaded locally by applying an electromagnetic field in order to produce an AE response, which may be captured by conventional or fiber optic (FO) AE sensors. The advantage of this technique is that the localized dynamic stresses induced by a short current pulse in the presence of an external magnetic field aid in the detection of cracks. Also, it is shown that electromagnetic stimulation can be applied to enhance conventional ultrasonics by modulation of the scattered signal from the defect (EM UT). Experimental data is presented for the case of a fatigue crack near rivet holes in thin walled aluminum structures.

Executive-Attentional Uncertainty Responses by Rhesus Macaques ("Macaca mulatta")

Science.gov (United States)

Smith, J. David; Coutinho, Mariana V. C.; Church, Barbara A.; Beran, Michael J.

2013-01-01

The uncertainty response has been influential in studies of human perception, and it is crucial in the growing research literature that explores animal metacognition. However, the uncertainty response's interpretation is still sharply debated. The authors sought to clarify this interpretation using the dissociative technique of cognitive loads…

A comparative study of CdS thin films deposited by different techniques

Energy Technology Data Exchange (ETDEWEB)

Pérez-Hernández, G., E-mail: german.perez@ujat.mx [Universidad Juárez Autónoma de Tabasco, Avenida Universidad s/n, Col. Magisterial, Villahermosa, Tabasco 86040 (Mexico); Pantoja-Enríquez, J. [Centro de Investigación y Desarrollo Tecnológico en Energías Renovables, UNICACH, Libramiento Norte No 1150, Tuxtla Gutiérrez, Chiapas 29039 (Mexico); Escobar-Morales, B. [Instituto Tecnológico de Cancún, Avenida Kábah Km 3, Cancún, Quintana Roo 77500 (Mexico); Martinez-Hernández, D.; Díaz-Flores, L.L.; Ricardez-Jiménez, C. [Universidad Juárez Autónoma de Tabasco, Avenida Universidad s/n, Col. Magisterial, Villahermosa, Tabasco 86040 (Mexico); Mathews, N.R.; Mathew, X. [Centro de Investigación en Energía, Universidad Nacional Autónoma de México, Temixco, Morelos 62580 (Mexico)

2013-05-01

Cadmium sulfide thin-films were deposited on glass slides and SnO{sub 2}:F coated glass substrates by chemical bath deposition, sputtering and close-spaced sublimation techniques. The films were studied for the structural and opto-electronic properties after annealing in an ambient identical to that employed in the fabrication of CdTe/CdS devices. Quantum efficiency of the CdTe/CdS solar cells fabricated with CdS buffer films prepared by the three methods were investigated to understand the role of CdS film preparation method on the blue response of the devices. The higher blue response observed for the devices fabricated with chemical bath deposited CdS film is discussed. - Highlights: ► CdS films were prepared by different techniques. ► Role of CdS on the blue response of device was studied. ► Structural and optical properties of CdS were analyzed. ► Chemically deposited CdS has high blue transmittance. ► CdS deposition method influences diffusion of S and Te.

A neutron calibration technique for detectors with low neutron/high photon sensitivity

International Nuclear Information System (INIS)

Jahr, R.; Guldbakke, S.; Cosack, M.; Dietze, G.; Klein, H.

1978-03-01

The neutron response of a detector with low neutron-/high photon sensitivity is given by the difference of two terms: the response to the mixed neutron-photon field, measured directly, and the response to the photons, deduced from additional measurements with a photon spectrometer. The technique is particularly suited for use in connection with targets which consist of a thick backing and thin layer of neutron producing material such as T, D, Li nuclei. Then the photon component of the mixed field is very nearly the same as the pure photon field from a 'phantom target', being identical with the neutron producing target except for the missing neutron producing material. Using this technique in connection with a T target (Ti-T-layer on silver backing) and the corresponding phantom target (Ti-layer on silver backing), a GM counter was calibrated at a neutron energy of 2.5 MeV. Possibilities are discussed to subsequently calibrate the GM counter at other neutron energies without the use of the photon spectrometer. (orig./HP) [de

What do potential jurors know about police interrogation techniques and false confessions?

Science.gov (United States)

Leo, Richard A; Liu, Brittany

2009-01-01

Psychological police interrogation methods in America inevitably involve some level of pressure and persuasion to achieve their goal of eliciting confessions of guilt from custodial suspects. In this article, we surveyed potential jurors about their perceptions of a range of psychological interrogation techniques, the likelihood that such techniques would elicit a true confession from guilty suspects, and the likelihood that such techniques could elicit a false confession from innocent suspects. Participants recognized that these interrogation techniques may be psychologically coercive and may elicit true confessions, but believed that psychologically coercive interrogation techniques are not likely to elicit false confessions. The findings from this survey study indicate that potential jurors believe that false confessions are both counter- intuitive and unlikely, even in response to psychologically coercive interrogation techniques that have been shown to lead to false confessions from the innocent. This study provides empirical support for the idea that expert witnesses may helpfully inform jurors about the social science research on psychologically coercive interrogation methods and how and why such interrogation techniques can lead to false confessions. (c) 2009 John Wiley & Sons, Ltd.

Determination of Flaw Size and Depth From Temporal Evolution of Thermal Response

Science.gov (United States)

Winfree, William P.; Zalameda, Joseph N.; Cramer, Elliott; Howell, Patricia A.

2015-01-01

Simple methods for reducing the pulsed thermographic responses of flaws have tended to be based on either the spatial or temporal response. This independent assessment limits the accuracy of characterization. A variational approach is presented for reducing the thermographic data to produce an estimated size for a flaw that incorporates both the temporal and spatial response to improve the characterization. The size and depth are determined from both the temporal and spatial thermal response of the exterior surface above a flaw and constraints on the length of the contour surrounding the delamination. Examples of the application of the technique to simulation and experimental data acquired are presented to investigate the limitations of the technique.

Cerebral blood flow measurement techniques in infants and children

International Nuclear Information System (INIS)

Kirsch, J.R.; Traystman, R.J.; Rogers, M.C.

1985-01-01

The tremendous growth of interest in neurologic intensive care and in the pathophysiology of the cerebral circulation in the past few years has resulted in increasing numbers of studies that document alterations in cerebral flow during the course of various diseases or as a response to treatment of them. Before pediatricians come to conclusions based on these studies, it is important to have an understanding of the techniques involved. The techniques are complex and difficult but are based on understandable principles. They also have limitations and are subject to misinterpretations. Pediatricians should become knowledgeable about some of these techniques and their limitations because it is likely that they will be applied with increasing frequency in the next several years. We are on the threshold of exciting discoveries in abnormalities of cerebral blood flow and cerebral metabolism not only in critically ill children but also in children with congenital and learning disorders

Fault Management Techniques in Human Spaceflight Operations

Science.gov (United States)

O'Hagan, Brian; Crocker, Alan

2006-01-01

This paper discusses human spaceflight fault management operations. Fault detection and response capabilities available in current US human spaceflight programs Space Shuttle and International Space Station are described while emphasizing system design impacts on operational techniques and constraints. Preflight and inflight processes along with products used to anticipate, mitigate and respond to failures are introduced. Examples of operational products used to support failure responses are presented. Possible improvements in the state of the art, as well as prioritization and success criteria for their implementation are proposed. This paper describes how the architecture of a command and control system impacts operations in areas such as the required fault response times, automated vs. manual fault responses, use of workarounds, etc. The architecture includes the use of redundancy at the system and software function level, software capabilities, use of intelligent or autonomous systems, number and severity of software defects, etc. This in turn drives which Caution and Warning (C&W) events should be annunciated, C&W event classification, operator display designs, crew training, flight control team training, and procedure development. Other factors impacting operations are the complexity of a system, skills needed to understand and operate a system, and the use of commonality vs. optimized solutions for software and responses. Fault detection, annunciation, safing responses, and recovery capabilities are explored using real examples to uncover underlying philosophies and constraints. These factors directly impact operations in that the crew and flight control team need to understand what happened, why it happened, what the system is doing, and what, if any, corrective actions they need to perform. If a fault results in multiple C&W events, or if several faults occur simultaneously, the root cause(s) of the fault(s), as well as their vehicle-wide impacts, must be

The design of a turboshaft speed governor using modern control techniques

Science.gov (United States)

Delosreyes, G.; Gouchoe, D. R.

1986-01-01

The objectives of this program were: to verify the model of off schedule compressor variable geometry in the T700 turboshaft engine nonlinear model; to evaluate the use of the pseudo-random binary noise (PRBN) technique for obtaining engine frequency response data; and to design a high performance power turbine speed governor using modern control methods. Reduction of T700 engine test data generated at NASA-Lewis indicated that the off schedule variable geometry effects were accurate as modeled. Analysis also showed that the PRBN technique combined with the maximum likelihood model identification method produced a Bode frequency response that was as accurate as the response obtained from standard sinewave testing methods. The frequency response verified the accuracy of linear models consisting of engine partial derivatives and used for design. A power turbine governor was designed using the Linear Quadratic Regulator (LQR) method of full state feedback control. A Kalman filter observer was used to estimate helicopter main rotor blade velocity. Compared to the baseline T700 power turbine speed governor, the LQR governor reduced droop up to 25 percent for a 490 shaft horsepower transient in 0.1 sec simulating a wind gust, and up to 85 percent for a 700 shaft horsepower transient in 0.5 sec simulating a large collective pitch angle transient.

Third molar development: evaluation of nine tooth development registration techniques for age estimations.

Science.gov (United States)

Thevissen, Patrick W; Fieuws, Steffen; Willems, Guy

2013-03-01

Multiple third molar development registration techniques exist. Therefore the aim of this study was to detect which third molar development registration technique was most promising to use as a tool for subadult age estimation. On a collection of 1199 panoramic radiographs the development of all present third molars was registered following nine different registration techniques [Gleiser, Hunt (GH); Haavikko (HV); Demirjian (DM); Raungpaka (RA); Gustafson, Koch (GK); Harris, Nortje (HN); Kullman (KU); Moorrees (MO); Cameriere (CA)]. Regression models with age as response and the third molar registration as predictor were developed for each registration technique separately. The MO technique disclosed highest R(2) (F 51%, M 45%) and lowest root mean squared error (F 3.42 years; M 3.67 years) values, but differences with other techniques were small in magnitude. The amount of stages utilized in the explored staging techniques slightly influenced the age predictions. © 2013 American Academy of Forensic Sciences.

Reconstruction of the residual stresses in a hyperelastic body using ultrasound techniques

KAUST Repository

Joshi, Sunnie; Walton, Jay R.

2013-01-01

This paper focuses on a novel approach for characterizing the residual stress field in soft tissue using ultrasound interrogation. A nonlinear inverse spectral technique is developed that makes fundamental use of the finite strain nonlinear response

Plant Responses to Nanoparticle Stress

Directory of Open Access Journals (Sweden)

Zahed Hossain

2015-11-01

Full Text Available With the rapid advancement in nanotechnology, release of nanoscale materials into the environment is inevitable. Such contamination may negatively influence the functioning of the ecosystems. Many manufactured nanoparticles (NPs contain heavy metals, which can cause soil and water contamination. Proteomic techniques have contributed substantially in understanding the molecular mechanisms of plant responses against various stresses by providing a link between gene expression and cell metabolism. As the coding regions of genome are responsible for plant adaptation to adverse conditions, protein signatures provide insights into the phytotoxicity of NPs at proteome level. This review summarizes the recent contributions of plant proteomic research to elaborate the complex molecular pathways of plant response to NPs stress.

The twitch interpolation technique for study of fatigue of human quadriceps muscle

DEFF Research Database (Denmark)

Bülow, P M; Nørregaard, J; Mehlsen, J

1995-01-01

The aim of the study was to examine if the twitch interpolation technique could be used to objectively measure fatigue in the quadriceps muscle in subjects performing submaximally. The 'true' maximum isometric quadriceps torque was determined in 21 healthy subject using the twitch interpolation...... technique. Then an endurance test was performed in which the subjects made repeated isometric contractions at 50% of the 'true' maximum torque for 4 s, separated by 6 s rest periods. During the test, the force response to single electrical stimulation (twitch amplitude) was measured at 50% and 25......). In conclusion, the twitch technique can be used for objectively measuring fatigue of the quadriceps muscle....

Seismic Response Analysis of Continuous Multispan Bridges with Partial Isolation

Directory of Open Access Journals (Sweden)

E. Tubaldi

2015-01-01

Full Text Available Partially isolated bridges are a particular class of bridges in which isolation bearings are placed only between the piers top and the deck whereas seismic stoppers restrain the transverse motion of the deck at the abutments. This paper proposes an analytical formulation for the seismic analysis of these bridges, modelled as beams with intermediate viscoelastic restraints whose properties describe the pier-isolator behaviour. Different techniques are developed for solving the seismic problem. The first technique employs the complex mode superposition method and provides an exact benchmark solution to the problem at hand. The two other simplified techniques are based on an approximation of the displacement field and are useful for preliminary assessment and design purposes. A realistic bridge is considered as case study and its seismic response under a set of ground motion records is analyzed. First, the complex mode superposition method is applied to study the characteristic features of the dynamic and seismic response of the system. A parametric analysis is carried out to evaluate the influence of support stiffness and damping on the seismic performance. Then, a comparison is made between the exact solution and the approximate solutions in order to evaluate the accuracy and suitability of the simplified analysis techniques for evaluating the seismic response of partially isolated bridges.

A simple technique can reduce cardiopulmonary bypass use during lung transplantation

Directory of Open Access Journals (Sweden)

Marcos N. Samano

2016-04-01

Full Text Available Cardiopulmonary bypass causes an inflammatory response and consumption of coagulation factors, increasing the risk of bleeding and neurological and renal complications. Its use during lung transplantation may be due to pulmonary hypertension or associated cardiac defects or just for better exposure of the pulmonary hilum. We describe a simple technique, or open pericardium retraction, to improve hilar exposure by lifting the heart by upward retraction of the pericardial sac. This technique permits lung transplantation without cardiopulmonary bypass when bypass use is recommended only for better exposure.

Using risk based tools in emergency response

International Nuclear Information System (INIS)

Dixon, B.W.; Ferns, K.G.

1987-01-01

Probabilistic Risk Assessment (PRA) techniques are used by the nuclear industry to model the potential response of a reactor subjected to unusual conditions. The knowledge contained in these models can aid in emergency response decision making. This paper presents requirements for a PRA based emergency response support system to date. A brief discussion of published work provides background for a detailed description of recent developments. A rapid deep assessment capability for specific portions of full plant models is presented. The program uses a screening rule base to control search space expansion in a combinational algorithm

Characterization techniques for graphene-based materials in catalysis

Directory of Open Access Journals (Sweden)

Maocong Hu

2017-06-01

Full Text Available Graphene-based materials have been studied in a wide range of applications including catalysis due to the outstanding electronic, thermal, and mechanical properties. The unprecedented features of graphene-based catalysts, which are believed to be responsible for their superior performance, have been characterized by many techniques. In this article, we comprehensively summarized the characterization methods covering bulk and surface structure analysis, chemisorption ability determination, and reaction mechanism investigation. We reviewed the advantages/disadvantages of different techniques including Raman spectroscopy, X-ray photoelectron spectroscopy (XPS, Fourier transform infrared spectroscopy (FTIR and Diffuse Reflectance Fourier Transform Infrared Spectroscopy (DRIFTS, X-Ray diffraction (XRD, X-ray absorption near edge structure (XANES and X-ray absorption fine structure (XAFS, atomic force microscopy (AFM, scanning electron microscopy (SEM, transmission electron microscopy (TEM, high-resolution transmission electron microscopy (HRTEM, ultraviolet-visible spectroscopy (UV-vis, X-ray fluorescence (XRF, inductively coupled plasma mass spectrometry (ICP, thermogravimetric analysis (TGA, Brunauer–Emmett–Teller (BET, and scanning tunneling microscopy (STM. The application of temperature-programmed reduction (TPR, CO chemisorption, and NH3/CO2-temperature-programmed desorption (TPD was also briefly introduced. Finally, we discussed the challenges and provided possible suggestions on choosing characterization techniques. This review provides key information to catalysis community to adopt suitable characterization techniques for their research.

Ambient Response Analysis Modal Analysis for Large Structures

DEFF Research Database (Denmark)

Brincker, Rune; Andersen, Palle

1999-01-01

In this paper an outline is given of the basic ideas in ambient respons analysis, i.e. when modal analyses is performed on systems based on output only. Some of the most known techniques are briefly introduced, and the basic problems discussed. The introduced techniques are the frequency domain...... based peak-picking methods, the polyreference LSCE method, the stochastic subspace method for estimation of state space systems and the prediction error method for estimation of Auto-Regressive Moving Average Vector models. The techniques are illustrated on an example of ambient response measurments...

Responsiveness of the rehabilitation activities profile and the Barthel index

NARCIS (Netherlands)

van Bennekom, C. A.; Jelles, F.; Lankhorst, G. J.; Bouter, L. M.

1996-01-01

The goal of this study was to compare the responsiveness for clinically meaningful change over time of a newly designed functional status scale, the Rehabilitation Activities Profile (RAP), with more frequently used Barthel Index (BI). Four techniques for the quantification of responsiveness were

Measuring gas-residence times in large municipal incinerators, by means of a pseudo-random binary signal tracer technique

International Nuclear Information System (INIS)

Nasserzadeh, V.; Swithenbank, J.; Jones, B.

1995-01-01

The problem of measuring gas-residence time in large incinerators was studied by the pseudo-random binary sequence (PRBS) stimulus tracer response technique at the Sheffield municipal solid-waste incinerator (35 MW plant). The steady-state system was disturbed by the superimposition of small fluctuations in the form of a pseudo-random binary sequence of methane pulses, and the response of the incinerator was determined from the CO 2 concentration in flue gases at the boiler exit, measured with a specially developed optical gas analyser with a high-frequency response. For data acquisition, an on-line PC computer was used together with the LAB Windows software system; the output response was then cross-correlated with the perturbation signal to give the impulse response of the incinerator. There was very good agreement between the gas-residence time for the Sheffield MSW incinerator as calculated by computational fluid dynamics (FLUENT Model) and gas-residence time at the plant as measured by the PRBS tracer technique. The results obtained from this research programme clearly demonstrate that the PRBS stimulus tracer response technique can be successfully and economically used to measure gas-residence times in large incinerator plants. It also suggests that the common commercial practice of characterising the incinerator operation by a single-residence-time parameter may lead to a misrepresentation of the complexities involved in describing the operation of the incineration system. (author)

Improved Nanomechanical Test Techniques for Surface Engineered Materials

Directory of Open Access Journals (Sweden)

Stephen R. Goodes

2010-06-01

Full Text Available The development and implementation of a wide range of innovative nanomechanical test techniques to solve tribological problems in applications as diverse as biomedical and automotive are described in this review. For improved wear resistance and durability, the importance of understanding the system response rather than the coating-only properties is emphasized. There are many applications involving mechanical contact where the key to understanding the problem is to test at higher load and to combine reliable measurements taken across different length scales using both nano- and micro-indentation and related wear measurement techniques which more closely simulate contact conditions to fully understand the mechanical behaviour and hence deliver improved application performance. Results are presented with the NanoTest platform for applications for biomedical devices and surface engineering of lightweight alloys for the automotive industry. By combining results with different techniques it is possible to postulate predictive design rules – based on the elastic and plastic deformation energies involved in contact - to aid the reliable optimisation of mechanical properties in the various contact situations in the different applications.

Cisatracurium dose–response relationship in patients with chronic liver disease

Directory of Open Access Journals (Sweden)

Mohamed Z. Ali

2014-04-01

Results: The preoperative laboratory parameters showed statistically significant differences between the two groups regarding serum albumin, total bilirubin, ALT, AST, PT, PC and INR. The operative data showed statistically insignificant difference between the two groups regarding the 1st dose response (p = 0.152, the estimated ED80 (p = 0.886 and the calculated 2nd dose (p = 0.886 and statistically significant differences between the two groups regarding the 2nd dose response (p = 0.006, the measured ED50 (p = 0.010 and the measured ED95 (p = 0.001. In conclusion, the measured ED50 and ED95 through two-dose dose–response curve technique were clinically insignificant from using the single-dose technique. The dose–response curve of cisatracurium in patients with chronic liver disease was clinically insignificant in comparison with healthy subjects.

Dismantling techniques

Energy Technology Data Exchange (ETDEWEB)

Wiese, E.

1998-03-13

Most of the dismantling techniques used in a Decontamination and Dismantlement (D and D) project are taken from conventional demolition practices. Some modifications to the techniques are made to limit exposure to the workers or to lessen the spread of contamination to the work area. When working on a D and D project, it is best to keep the dismantling techniques and tools as simple as possible. The workers will be more efficient and safer using techniques that are familiar to them. Prior experience with the technique or use of mock-ups is the best way to keep workers safe and to keep the project on schedule.

Dismantling techniques

International Nuclear Information System (INIS)

Wiese, E.

1998-01-01

Most of the dismantling techniques used in a Decontamination and Dismantlement (D and D) project are taken from conventional demolition practices. Some modifications to the techniques are made to limit exposure to the workers or to lessen the spread of contamination to the work area. When working on a D and D project, it is best to keep the dismantling techniques and tools as simple as possible. The workers will be more efficient and safer using techniques that are familiar to them. Prior experience with the technique or use of mock-ups is the best way to keep workers safe and to keep the project on schedule

Meta-Analysis of Free-Response Studies, 1992-2008: Assessing the Noise Reduction Model in Parapsychology

Science.gov (United States)

Storm, Lance; Tressoldi, Patrizio E.; Di Risio, Lorenzo

2010-01-01

We report the results of meta-analyses on 3 types of free-response study: (a) ganzfeld (a technique that enhances a communication anomaly referred to as "psi"); (b) nonganzfeld noise reduction using alleged psi-enhancing techniques such as dream psi, meditation, relaxation, or hypnosis; and (c) standard free response (nonganzfeld, no noise…

Performance optimization in electro- discharge machining using a suitable multiresponse optimization technique

Directory of Open Access Journals (Sweden)

I. Nayak

2017-06-01

Full Text Available In the present research work, four different multi response optimization techniques, viz. multiple response signal-to-noise (MRSN ratio, weighted signal-to-noise (WSN ratio, Grey relational analysis (GRA and VIKOR (VlseKriterijumska Optimizacija I Kompromisno Resenje in Serbian methods have been used to optimize the electro-discharge machining (EDM performance characteristics such as material removal rate (MRR, tool wear rate (TWR and surface roughness (SR simultaneously. Experiments have been planned on a D2 steel specimen based on L9 orthogonal array. Experimental results are analyzed using the standard procedure. The optimum level combinations of input process parameters such as voltage, current, pulse-on-time and pulse-off-time, and percentage contributions of each process parameter using ANOVA technique have been determined. Different correlations have been developed between the various input process parameters and output performance characteristics. Finally, the optimum performances of these four methods are compared and the results show that WSN ratio method is the best multiresponse optimization technique for this process. From the analysis, it is also found that the current has the maximum effect on the overall performance of EDM operation as compared to other process parameters.

Neuron responses to substance P and enkephalin in rat dorso-lateral septum in vitro.

Science.gov (United States)

Nayar, R; Sirett, N E; Hubbard, J I

1987-10-01

Using an in vitro brain slice technique the responses of spontaneously active neurons in the rat dorso-lateral septum to 10 nM substance P (SP) and enkephalin were determined. Fewer neurons responded to SP (41%) than to enkephalin (55%). The SP responses were 13 excitations, 14 inhibitions, the enkephalin responses were 13 excitations, 14 inhibitions and 11 responded to both, 6 of these were inhibited by both. Immunocytochemical techniques have shown there is a discrete localisation of SP and enkephalin axons and terminals in the rat septum. SP responsive neurons were associated with the SP terminal-rich region (p = 0.01) but no association was found for enkephalin responses in the enkephalin terminal-rich region (p = 0.7).

The Shock and Vibration Bulletin. Part 4. Prediction and Experimental Techniques, Isolation and Damping

Science.gov (United States)

1973-06-01

D. 0. Smallwood , Sandia Laboratories, Albuquerque, New Mexico and A. F. Witte, Kaman Sciences, Colorado Springs, Colorado fi TRANSIENT VIBRATION...TEST TECHNIQUE USING LEAST FAVORABLE RESPONSES D. O. Smallwood , Sandia Laboratories, Albuquerque, New Mexico PAPERS APPEARING IN PART 2 Structural...Dynamic Systems, Measure- ments and Control, March 1971. 12. Favour, John D., Maclom C. Mitchell, and Norman L. Olson, "Transient Test Techniques for

Considering Mindfulness Techniques in School-based Anti-bullying Programmes

Directory of Open Access Journals (Sweden)

Mairead Foody

2018-01-01

Full Text Available Schools have a duty of care to all students and to directly prevent and intervene with bullying amongst children and adolescents. The emergence of cyberbullying escalates this responsibility as the strategies that have become appropriate at national levels for bullying do not always parallel over to online environments. The impact on mental health is the most obvious concern for those responsible for reducing bullying, however, input from psychologists and mental health professionals is scant and often limited on this topic. This paper outlines what bullying is and the devastating impact it can have on the mental health of those involved. It will outline the most common anti-bullying initiatives as well as the current psychological and educational techniques, which could also be used to alleviate distress associated with bullying involvement. We will focus specifically on the role of mindfulness techniques and argue for more of such exercises to be included in whole-school bullying programmes. We conclude by arguing the need to investigate components relevant to both mindfulness and anti-bullying programmes (e.g., empathy, perspective-taking as active ingredients for reducing the impact of bullying on mental health.

Subliminal Cues While Teaching: HCI Technique for Enhanced Learning

Directory of Open Access Journals (Sweden)

Pierre Chalfoun

2011-01-01

Full Text Available This paper presents results from an empirical study conducted with a subliminal teaching technique aimed at enhancing learner's performance in Intelligent Systems through the use of physiological sensors. This technique uses carefully designed subliminal cues (positive and miscues (negative and projects them under the learner's perceptual visual threshold. A positive cue, called answer cue, is a hint aiming to enhance the learner's inductive reasoning abilities and projected in a way to help them figure out the solution faster but more importantly better. A negative cue, called miscue, is also used and aims at obviously at the opposite (distract the learner or lead them to the wrong conclusion. The latest obtained results showed that only subliminal cues, not miscues, could significantly increase learner performance and intuition in a logic-based problem-solving task. Nonintrusive physiological sensors (EEG for recording brainwaves, blood volume pressure to compute heart rate and skin response to record skin conductivity were used to record affective and cerebral responses throughout the experiment. The descriptive analysis, combined with the physiological data, provides compelling evidence for the positive impact of answer cues on reasoning and intuitive decision making in a logic-based problem-solving paradigm.

The effect of numerical techniques on differential equation based chaotic generators

KAUST Repository

Zidan, Mohammed A.

2012-07-29

In this paper, we study the effect of the numerical solution accuracy on the digital implementation of differential chaos generators. Four systems are built on a Xilinx Virtex 4 FPGA using Euler, mid-point, and Runge-Kutta fourth order techniques. The twelve implementations are compared based on the FPGA used area, maximum throughput, maximum Lyapunov exponent, and autocorrelation confidence region. Based on circuit performance and the chaotic response of the different implementations, it was found that less complicated numerical solution has better chaotic response and higher throughput.

Admission Control Techniques for UMTS System

Directory of Open Access Journals (Sweden)

P. Kejik

2010-09-01

Full Text Available Universal mobile telecommunications system (UMTS is one of the 3rd generation (3G cell phone technologies. The capacity of UMTS is interference limited. Radio resources management (RRM functions are therefore used. They are responsible for supplying optimum coverage, ensuring efficient use of physical resources, and providing the maximum planned capacity. This paper deals with admission control techniques for UMTS. An own UMTS simulation program and several versions of proposed admission control algorithms are presented in this paper. These algorithms are based on fuzzy logic and genetic algorithms. The performance of algorithms is verified via simulations.

Fabrications and Applications of Stimulus-Responsive Polymer Films and Patterns on Surfaces: A Review

Directory of Open Access Journals (Sweden)

Jem-Kun Chen

2014-01-01

Full Text Available In the past two decades, we have witnessed significant progress in developing high performance stimuli-responsive polymeric materials. This review focuses on recent developments in the preparation and application of patterned stimuli-responsive polymers, including thermoresponsive layers, pH/ionic-responsive hydrogels, photo-responsive film, magnetically-responsive composites, electroactive composites, and solvent-responsive composites. Many important new applications for stimuli-responsive polymers lie in the field of nano- and micro-fabrication, where stimuli-responsive polymers are being established as important manipulation tools. Some techniques have been developed to selectively position organic molecules and then to obtain well-defined patterned substrates at the micrometer or submicrometer scale. Methods for patterning of stimuli-responsive hydrogels, including photolithography, electron beam lithography, scanning probe writing, and printing techniques (microcontact printing, ink-jet printing were surveyed. We also surveyed the applications of nanostructured stimuli-responsive hydrogels, such as biotechnology (biological interfaces and purification of biomacromoles, switchable wettability, sensors (optical sensors, biosensors, chemical sensors, and actuators.

CRDM motion analysis using machine learning technique

International Nuclear Information System (INIS)

Nishimura, Takuya; Nakayama, Hiroyuki; Saitoh, Mayumi; Yaguchi, Seiji

2017-01-01

Magnetic jack type Control Rod Drive Mechanism (CRDM) for pressurized water reactor (PWR) plant operates control rods in response to electrical signals from a reactor control system. CRDM operability is evaluated by quantifying armature's response of closed/opened time which means interval time between coil energizing/de-energizing points and armature closed/opened points. MHI has already developed an automatic CRDM motion analysis and applied it to actual plants so far. However, CRDM operational data has wide variation depending on their characteristics such as plant condition, plant, etc. In the existing motion analysis, there is an issue of analysis accuracy for applying a single analysis technique to all plant conditions, plants, etc. In this study, MHI investigated motion analysis using machine learning (Random Forests) which is flexibly accommodated to CRDM operational data with wide variation, and is improved analysis accuracy. (author)

Identifying Careless Responses in Survey Data

Science.gov (United States)

Meade, Adam W.; Craig, S. Bartholomew

2012-01-01

When data are collected via anonymous Internet surveys, particularly under conditions of obligatory participation (such as with student samples), data quality can be a concern. However, little guidance exists in the published literature regarding techniques for detecting careless responses. Previously several potential approaches have been…

Static contribution of the higher modes in the dynamic response of structures

International Nuclear Information System (INIS)

Barbosa, H.J.C.

1982-03-01

In the dynamic response of structures by the modal superposition method usually only the lower modes are taken into account and a procedure that could estimate the contribution due to the higher modes without calculating them would be useful. The technique which consists of assuming that the higher modes respond statically is discussed here. Structures subjected to support motion which are analysed by response spectra techniques are considered and some numerical results are presented. (Author) [pt

Corporate Social Responsibility in Aviation

Science.gov (United States)

Phillips, Edwin D.

2006-01-01

The dialog within aviation management education regarding ethics is incomplete without a discussion of corporate social responsibility (CSR). CSR research requires discussion involving: (a) the current emphasis on CSR in business in general and aviation specifically; (b) business and educational theory that provide a basis for aviation companies to engage in socially responsible actions; (c) techniques used by aviation and aerospace companies to fulfill this responsibility; and (d) a glimpse of teaching approaches used in university aviation management classes. The summary of this research suggests educators explain CSR theory and practice to students in industry and collegiate aviation management programs. Doing so extends the discussion of ethical behavior and matches the current high level of interest and activity within the aviation industry toward CSR.

Storytelling: a teaching-learning technique.

Science.gov (United States)

Geanellos, R

1996-03-01

Nurses' stories, arising from the practice world, reconstruct the essence of experience as lived and provide vehicles for learning about nursing. The learning process is forwarded by combining storytelling and reflection. Reflection represents an active, purposive, contemplative and deliberative approach to learning through which learners create meaning from the learning experience. The combination of storytelling and reflection allows the creation of links between the materials at hand and prior and future learning. As a teaching-learning technique storytelling engages learners; organizes information; allows exploration of shared lived experiences without the demands, responsibilities and consequences of practice; facilitates remembering; enhances discussion, problem posing and problem solving; and aids understanding of what it is to nurse and to be a nurse.

Arbitrary magnetic field gradient waveform correction using an impulse response based pre-equalization technique.

Science.gov (United States)

Goora, Frédéric G; Colpitts, Bruce G; Balcom, Bruce J

2014-01-01

The time-varying magnetic fields used in magnetic resonance applications result in the induction of eddy currents on conductive structures in the vicinity of both the sample under investigation and the gradient coils. These eddy currents typically result in undesired degradations of image quality for MRI applications. Their ubiquitous nature has resulted in the development of various approaches to characterize and minimize their impact on image quality. This paper outlines a method that utilizes the magnetic field gradient waveform monitor method to directly measure the temporal evolution of the magnetic field gradient from a step-like input function and extracts the system impulse response. With the basic assumption that the gradient system is sufficiently linear and time invariant to permit system theory analysis, the impulse response is used to determine a pre-equalized (optimized) input waveform that provides a desired gradient response at the output of the system. An algorithm has been developed that calculates a pre-equalized waveform that may be accurately reproduced by the amplifier (is physically realizable) and accounts for system limitations including system bandwidth, amplifier slew rate capabilities, and noise inherent in the initial measurement. Significant improvements in magnetic field gradient waveform fidelity after pre-equalization have been realized and are summarized. Copyright © 2013 Elsevier Inc. All rights reserved.

Techniques for site investigations for underground disposal of radioactive wastes

International Nuclear Information System (INIS)

1985-01-01

The report provides a more detailed description of the capabilities and applications of the various earth science investigation techniques outlined in the IAEA Technical Reports Series Nos. 177, 215 and 216. These methods are generally appropriate during at least one of the stages of the assessment or selection of a site for any type of waste disposal facility, in shallow ground or in deep geological formations. This report is addressed to technical authorities responsible for or involved in planning, approving, executing and reviewing national waste disposal programmes. It may also help administrative authorities in this field to select appropriate techniques for obtaining the majority of the required information at minimum cost

A Technique for Developing Probabilistic Properties of Earth Materials

Science.gov (United States)

1988-04-01

with those obtained from probabilistic predic- tion calculations was developed by Baladi and Barnes (Reference 11). By caloulating the magnitude and...Therefore, a technique to smooth the measured ddta without changing the intrinsic response is needed. Such a procedure was developed by Baladi and...2.2.2 Covariance Analysis of Smoothed Data A generic procedure for statistically analyzing nonlinear data was developed by Baladi and Rohani

Filtered backprojection for modifying the impulse response of circular tomosynthesis

International Nuclear Information System (INIS)

Stevens, Grant M.; Fahrig, Rebecca; Pelc, Norbert J.

2001-01-01

A filtering technique has been developed to modify the three-dimensional impulse response of circular motion tomosynthesis to allow the generation of images whose appearance is like those of some other imaging geometries. In particular, this technique can reconstruct images with a blurring function which is more homogeneous for off-focal plane objects than that from circular tomosynthesis. In this paper, we describe the filtering process, and demonstrate the ability to alter the impulse response in circular motion tomosynthesis from a ring to a disk. This filtering may be desirable because the blurred out-of-plane objects appear less structured

Impulse response identification with deterministic inputs using non-parametric methods

International Nuclear Information System (INIS)

Bhargava, U.K.; Kashyap, R.L.; Goodman, D.M.

1985-01-01

This paper addresses the problem of impulse response identification using non-parametric methods. Although the techniques developed herein apply to the truncated, untruncated, and the circulant models, we focus on the truncated model which is useful in certain applications. Two methods of impulse response identification will be presented. The first is based on the minimization of the C/sub L/ Statistic, which is an estimate of the mean-square prediction error; the second is a Bayesian approach. For both of these methods, we consider the effects of using both the identity matrix and the Laplacian matrix as weights on the energy in the impulse response. In addition, we present a method for estimating the effective length of the impulse response. Estimating the length is particularly important in the truncated case. Finally, we develop a method for estimating the noise variance at the output. Often, prior information on the noise variance is not available, and a good estimate is crucial to the success of estimating the impulse response with a nonparametric technique

Biological limits of the undersized surgical technique: a study in goats

NARCIS (Netherlands)

Tabassum, A.; Meijer, G.J.; Walboomers, X.F.; Jansen, J.A.

2011-01-01

OBJECTIVE: The purpose of the present study was to investigate the influence of different implant placement techniques on the early bone healing response in an animal model. MATERIAL AND METHODS: In the present study, 24 cylindrical-screw-type implants with a diameter of 4.2 mm (Dyna(R)) were

Verification Techniques for Parameter Selection and Bayesian Model Calibration Presented for an HIV Model

Science.gov (United States)

Wentworth, Mami Tonoe

Uncertainty quantification plays an important role when making predictive estimates of model responses. In this context, uncertainty quantification is defined as quantifying and reducing uncertainties, and the objective is to quantify uncertainties in parameter, model and measurements, and propagate the uncertainties through the model, so that one can make a predictive estimate with quantified uncertainties. Two of the aspects of uncertainty quantification that must be performed prior to propagating uncertainties are model calibration and parameter selection. There are several efficient techniques for these processes; however, the accuracy of these methods are often not verified. This is the motivation for our work, and in this dissertation, we present and illustrate verification frameworks for model calibration and parameter selection in the context of biological and physical models. First, HIV models, developed and improved by [2, 3, 8], describe the viral infection dynamics of an HIV disease. These are also used to make predictive estimates of viral loads and T-cell counts and to construct an optimal control for drug therapy. Estimating input parameters is an essential step prior to uncertainty quantification. However, not all the parameters are identifiable, implying that they cannot be uniquely determined by the observations. These unidentifiable parameters can be partially removed by performing parameter selection, a process in which parameters that have minimal impacts on the model response are determined. We provide verification techniques for Bayesian model calibration and parameter selection for an HIV model. As an example of a physical model, we employ a heat model with experimental measurements presented in [10]. A steady-state heat model represents a prototypical behavior for heat conduction and diffusion process involved in a thermal-hydraulic model, which is a part of nuclear reactor models. We employ this simple heat model to illustrate verification

The Silence of Corruption : Identifying Underreporting of Business Corruption through Randomized Response Techniques

OpenAIRE

Jensen, Nathan M.; Rahman, Aminur

2011-01-01

Research on the economic consequences of corruption has been hampered by the inability to directly measure corruption. Using an innovative methodology that allows respondents to report individual experiences with corruption while minimizing self-incrimination and an objective diagnostic to evaluate lying (false responses), this paper explores the extent of business corruption in Bangladesh...

A 200 mA CMOS low-dropout regulator with double frequency compensation techniques for SoC applications

International Nuclear Information System (INIS)

Lei Qianqian; Chen Zhiming; Gong Zheng; Shi Yin

2011-01-01

This paper presents a 200 mA low-dropout (LDO) linear regulator using two modified techniques for frequency compensation. One technique is that the error amplifier uses a common source stage with variable load, which is controlled by the output current, is served as the second stage for a stable frequency response. The other technique is that the LDO uses a pole-zero tracking compensation technique at the error amplifier to achieve a good frequency response. The proposed circuit was fabricated and tested in HJTC 0.18 μm CMOS technology. The designed LDO linear regulator works under the input voltage of 2.8–5 V and provides up to 200 mA load current for an output voltage of 1.8 V. The total error of the output voltage due to line and load variation is less than 0.015%. The LDO die area is 630 × 550 μm 2 and the quiescent current is 130 μA. (semiconductor integrated circuits)

Optimization technique applied to interpretation of experimental data and research of constitutive laws

International Nuclear Information System (INIS)

Grossette, J.C.

1982-01-01

The feasibility of identification technique applied to one dimensional numerical analysis of the split-Hopkinson pressure bar experiment is proven. A general 1-D elastic-plastic-viscoplastic computer program was written down so as to give an adequate solution for elastic-plastic-viscoplastic response of a pressure bar subjected to a general Heaviside step loading function in time which is applied over one end of the bar. Special emphasis is placed on the response of the specimen during the first microseconds where no equilibrium conditions can be stated. During this transient phase discontinuity conditions related to wave propagation are encountered and must be carefully taken into account. Having derived an adequate numerical model, then Pontryagin identification technique has been applied in such a way that the unknowns are physical parameters. The solutions depend mainly on the selection of a class of proper eigen objective functionals (cost functions) which may be combined so as to obtain a convenient numerical objective function. A number of significant questions arising in the choice of parameter adjustment algorithms are discussed. In particular, this technique leads to a two point boundary value problem which has been solved using an iterative gradient like technique usually referred to as a double operator gradient method. This method combines the classical Fletcher-Powell technique and a partial quadratic technique with an automatic parameter step size selection. This method is much more efficient than usual ones. Numerical experimentation with simulated data was performed to test the accuracy and stability of the identification algorithm and to determine the most adequate type and quantity of data for estimation purposes

Piloted Simulator Investigation of Techniques to Achieve Attitude Command Response with Limited Authority Servos

National Research Council Canada - National Science Library

Key, David

2002-01-01

The purpose of the study was to develop generic design principles for obtaining attitude command response in moderate to aggressive maneuvers without increasing SCAS series servo authority from the existing +/- 10...

Smart techniques in the dynamic spectrum alocation for cognitive wireless networks

Directory of Open Access Journals (Sweden)

Camila Salgado

2016-09-01

Full Text Available Objective: The objective of this work is to study the applications of different techniques of artificial intelligence and autonomous learning in the dynamic allocation of spectrum for cognitive wireless networks, especially the distributed ones. Method: The development of this work was done through the study and analysis of some of the most relevant publications in current literature through the search in indexed international journals in ISI and Scopus. Results: the most relevant techniques of artificial intelligence and autonomous learning were determined. Also, the ones with more applicability in the allocation of spectrum for cognitive wireless networks were determined, too. . Conclusions: The implementation of a technique, or set of them, depends on the needs in signal processing, compensation in response times, sample availability, storage capacity, learning ability and robustness, among others.

Comparison between correlated sampling and the perturbation technique of MCNP5 for fixed-source problems

International Nuclear Information System (INIS)

He Tao; Su Bingjing

2011-01-01

Highlights: → The performance of the MCNP differential operator perturbation technique is compared with that of the MCNP correlated sampling method for three types of fixed-source problems. → In terms of precision, the MCNP perturbation technique outperforms correlated sampling for one type of problem but performs comparably with or even under-performs correlated sampling for the other two types of problems. → In terms of accuracy, the MCNP perturbation calculations may predict inaccurate results for some of the test problems. However, the accuracy can be improved if the midpoint correction technique is used. - Abstract: Correlated sampling and the differential operator perturbation technique are two methods that enable MCNP (Monte Carlo N-Particle) to simulate small response change between an original system and a perturbed system. In this work the performance of the MCNP differential operator perturbation technique is compared with that of the MCNP correlated sampling method for three types of fixed-source problems. In terms of precision of predicted response changes, the MCNP perturbation technique outperforms correlated sampling for the problem involving variation of nuclide concentrations in the same direction but performs comparably with or even underperforms correlated sampling for the other two types of problems that involve void or variation of nuclide concentrations in opposite directions. In terms of accuracy, the MCNP differential operator perturbation calculations may predict inaccurate results that deviate from the benchmarks well beyond their uncertainty ranges for some of the test problems. However, the accuracy of the MCNP differential operator perturbation can be improved if the midpoint correction technique is used.

Estimation of fracture parameters in foam core materials using thermal techniques

DEFF Research Database (Denmark)

Dulieu-Barton, J. M.; Berggreen, Christian; Boyenval Langlois, C.

2010-01-01

is described. A mode I simulated crack in the form of a machined notch is used to establish the feasibility of the TSA approach to derive stress intensity factors for the foam material. The overall goal is to demonstrate that thermal techniques have the ability to provide deeper insight into the behaviour......The paper presents some initial work on establishing the stress state at a crack tip in PVC foam material using a non-contact infra-red technique known as thermoelastic stress analysis (TSA). A parametric study of the factors that may affect the thermoelastic response of the foam material...

Seismic qualification of nuclear control board by using base isolation technique

International Nuclear Information System (INIS)

Koizumi, T.; Tsujiuchi, N.; Fujita, T.

1987-01-01

The purpose is to adopt base isolation technique as a new approach for seismic qualification of nuclear control board. Basic concept of base isolation technique is expressed. Two dimensional linear motion mechanism with pre-tensioned coil springs and some dampers are included in the isolation device. Control board is regarded as a lamped mass system with inertia moment. Fundamental movement of this device and control board is calculated as a non-linear response problems. Fundamental analysis and numerical estimation, experimental investigation has been undertaken using an actual size control board. Sufficient agreement was recognized between experimental results and numerical estimation. (orig./HP)

Assessment of ground-based monitoring techniques applied to landslide investigations

Science.gov (United States)

Uhlemann, S.; Smith, A.; Chambers, J.; Dixon, N.; Dijkstra, T.; Haslam, E.; Meldrum, P.; Merritt, A.; Gunn, D.; Mackay, J.

2016-01-01

A landslide complex in the Whitby Mudstone Formation at Hollin Hill, North Yorkshire, UK is periodically re-activated in response to rainfall-induced pore-water pressure fluctuations. This paper compares long-term measurements (i.e., 2009-2014) obtained from a combination of monitoring techniques that have been employed together for the first time on an active landslide. The results highlight the relative performance of the different techniques, and can provide guidance for researchers and practitioners for selecting and installing appropriate monitoring techniques to assess unstable slopes. Particular attention is given to the spatial and temporal resolutions offered by the different approaches that include: Real Time Kinematic-GPS (RTK-GPS) monitoring of a ground surface marker array, conventional inclinometers, Shape Acceleration Arrays (SAA), tilt meters, active waveguides with Acoustic Emission (AE) monitoring, and piezometers. High spatial resolution information has allowed locating areas of stability and instability across a large slope. This has enabled identification of areas where further monitoring efforts should be focused. High temporal resolution information allowed the capture of 'S'-shaped slope displacement-time behaviour (i.e. phases of slope acceleration, deceleration and stability) in response to elevations in pore-water pressures. This study shows that a well-balanced suite of monitoring techniques that provides high temporal and spatial resolutions on both measurement and slope scale is necessary to fully understand failure and movement mechanisms of slopes. In the case of the Hollin Hill landslide it enabled detailed interpretation of the geomorphological processes governing landslide activity. It highlights the benefit of regularly surveying a network of GPS markers to determine areas for installation of movement monitoring techniques that offer higher resolution both temporally and spatially. The small sensitivity of tilt meter measurements

Impact of Damping Uncertainty on SEA Model Response Variance

Science.gov (United States)

Schiller, Noah; Cabell, Randolph; Grosveld, Ferdinand

2010-01-01

Statistical Energy Analysis (SEA) is commonly used to predict high-frequency vibroacoustic levels. This statistical approach provides the mean response over an ensemble of random subsystems that share the same gross system properties such as density, size, and damping. Recently, techniques have been developed to predict the ensemble variance as well as the mean response. However these techniques do not account for uncertainties in the system properties. In the present paper uncertainty in the damping loss factor is propagated through SEA to obtain more realistic prediction bounds that account for both ensemble and damping variance. The analysis is performed on a floor-equipped cylindrical test article that resembles an aircraft fuselage. Realistic bounds on the damping loss factor are determined from measurements acquired on the sidewall of the test article. The analysis demonstrates that uncertainties in damping have the potential to significantly impact the mean and variance of the predicted response.

Analysis and Implementation of Nonlinear Transducer Response over a Wider Response Range

Directory of Open Access Journals (Sweden)

Sheroz Khan

2008-03-01

Full Text Available In today’s automation systems transducers are making core elements in the instruments and the circuits used for measurement, control and industrial applications. The task of a transducer is to reproduce a physical quantity as an electrical signal which with the help of conditioning circuits, is transformed into a form that suits a corresponding ADC requirement before a digital equivalent output of the required physical quantity is produced. In the most ideal cases a digital quantity is a true replica of the physical quantity when the transducer has got a linear response. However, in most of the cases the transducers characteristics are nonlinear, and hence at very points along the whole range of the transducer characteristics, the corresponding digital output is an exact replica of the concerned physical parameter. This work is about how a physical read more accurately in the case of nonlinear sensor characteristics, and then a microcontroller is programmed with the same technique while reading from an input over the entire range. The data of the microcontroller reading shows very closely matched with the actual sensors response. Further, the reading error is considerably reduced to within 10 % of the actual physical which shows the utility of the technique in very sensitive applications.

A flight investigation of oscillating air forces: Equipment and technique

Science.gov (United States)

Reed, W. H., III

1975-01-01

The equipment and techniques are described which are to be used in a project aimed at measuring oscillating air forces and dynamic aeroelastic response of a swept wing airplane at high subsonic speeds. Electro-hydraulic inertia type shakers installed in the wing tips will excite various elastic airplane modes while the related oscillating chordwise pressures at two spanwise wing stations and the wing mode shapes are recorded on magnetic tape. The data reduction technique, following the principle of a wattmeter harmonic analyzer employed by Bratt, Wight, and Tilly, utilizes magnetic tape and high speed electronic multipliers to record directly the real and imaginary components of oscillatory data signals relative to a simple harmonic reference signal. Through an extension of this technique an automatic flight-flutter-test data analyzer is suggested in which vector plots of mechanical admittance or impedance would be plotted during the flight test.

The mathematical structure of the approximate linear response relation

International Nuclear Information System (INIS)

Yasuda, Muneki; Tanaka, Kazuyuki

2007-01-01

In this paper, we study the mathematical structures of the linear response relation based on Plefka's expansion and the cluster variation method in terms of the perturbation expansion, and we show how this linear response relation approximates the correlation functions of the specified system. Moreover, by comparing the perturbation expansions of the correlation functions estimated by the linear response relation based on these approximation methods with exact perturbative forms of the correlation functions, we are able to explain why the approximate techniques using the linear response relation work well

Comparison of bougie-guided insertion of Proseal tm laryngeal mask airway with digital technique in adults

Directory of Open Access Journals (Sweden)

Anand Kuppusamy

2010-01-01

Full Text Available The Proseal TM laryngeal mask airway (PLMA TM , Laryngeal Mask Company, UK was designed to improve ventilatory characteristics and offer protection against regurgitation and gastric insufflation. The PLMA is a modified laryngeal mask airway with large ventral cuff, dorsal cuff and a drain tube. These modifications improve seal around glottis and enable better ventilatory characteristics. The drain tube prevents gastric distension and offers protection against aspiration. There were occasional problems, like failed insertion and inadequate ventilation, in placing PLMA TM using the classical digital technique. To overcome these problems, newer placement techniques like thumb insertion technique, introducer tool placement and gum elastic bougie (GEB-aided placement were devised. We compared classical digital placement of PLMA TM with gum elastic bougie-aided technique in 60 anaesthetised adult patients (with 30 patients in each group with respect to number of attempts to successful placement, effective airway time, airway trauma during insertion, postoperative airway morbidity and haemodynamic response to insertion. The number of attempts to successful placement, airway trauma during insertion and haemodynamic response to insertion were comparable among the two groups, while effective airway time and oropharyngeal leak pressure were significantly higher in bougie- guided insertion of PLMA. Postoperatively, sore throat was more frequent with digital technique while dysphagia was more frequent with bougie-guided technique. Hence gum elastic bougie guided, laryngoscope aided insertion of PLMA is an excellent alternate to classical digital technique.

The Hydrogen Detection Technique for SG Protection System

International Nuclear Information System (INIS)

Lv Mingyu; Pei Zhiyong; Yu Huajin

2015-01-01

SG that is pressure boundary between secondary loop and triple loop is the key equipment of fast reactor, in which heat in secondary loop is transferred to water or steam in triple loop. According to data from IAEA, SG is the highest failure rate equipment in fast reactor, especially because of failure of heat transfer tube. In order to monitor failure of heat transfer tube, Fast Reactor Engineering Department develops diffusion type hydrogen detection system, which is used to detect sodium-water reaction in time. This paper firstly introduces experimental research scheme and results of this hydrogen detection technique; Subsequently, it is described that how this technique can be engineering realized in CEFR; Moreover, through developing a series of calibration tests and hydrogen injection tests, it is obtained that sensitivity, response time and calibration curse for hydrogen detection system of CEFR. (author)

The Recommendations for Linear Measurement Techniques on the Measurements of Nonlinear System Parameters of a Joint.

Energy Technology Data Exchange (ETDEWEB)

Smith, Scott A [Univ. of Maryland Baltimore County (UMBC), Baltimore, MD (United States); Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Catalfamo, Simone [Univ. of Stuttgart (Germany); Brake, Matthew R. W. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Rice Univ., Houston, TX (United States); Schwingshackl, Christoph W. [Imperial College, London (United Kingdom); Reusb, Pascal [Daimler AG, Stuttgart (Germany)

2017-01-01

In the study of the dynamics of nonlinear systems, experimental measurements often convolute the response of the nonlinearity of interest and the effects of the experimental setup. To reduce the influence of the experimental setup on the deduction of the parameters of the nonlinearity, the response of a mechanical joint is investigated under various experimental setups. These experiments first focus on quantifying how support structures and measurement techniques affect the natural frequency and damping of a linear system. The results indicate that support structures created from bungees have negligible influence on the system in terms of frequency and damping ratio variations. The study then focuses on the effects of the excitation technique on the response for a linear system. The findings suggest that thinner stingers should not be used, because under the high force requirements the stinger bending modes are excited adding unwanted torsional coupling. The optimal configuration for testing the linear system is then applied to a nonlinear system in order to assess the robustness of the test configuration. Finally, recommendations are made for conducting experiments on nonlinear systems using conventional/linear testing techniques.

Evaluation of an advanced physical diagnosis course using consumer preferences methods: the nominal group technique.

Science.gov (United States)

Coker, Joshua; Castiglioni, Analia; Kraemer, Ryan R; Massie, F Stanford; Morris, Jason L; Rodriguez, Martin; Russell, Stephen W; Shaneyfelt, Terrance; Willett, Lisa L; Estrada, Carlos A

2014-03-01

Current evaluation tools of medical school courses are limited by the scope of questions asked and may not fully engage the student to think on areas to improve. The authors sought to explore whether a technique to study consumer preferences would elicit specific and prioritized information for course evaluation from medical students. Using the nominal group technique (4 sessions), 12 senior medical students prioritized and weighed expectations and topics learned in a 100-hour advanced physical diagnosis course (4-week course; February 2012). Students weighted their top 3 responses (top = 3, middle = 2 and bottom = 1). Before the course, 12 students identified 23 topics they expected to learn; the top 3 were review sensitivity/specificity and high-yield techniques (percentage of total weight, 18.5%), improving diagnosis (13.8%) and reinforce usual and less well-known techniques (13.8%). After the course, students generated 22 topics learned; the top 3 were practice and reinforce advanced maneuvers (25.4%), gaining confidence (22.5%) and learn the evidence (16.9%). The authors observed no differences in the priority of responses before and after the course (P = 0.07). In a physical diagnosis course, medical students elicited specific and prioritized information using the nominal group technique. The course met student expectations regarding education of the evidence-based physical examination, building skills and confidence on the proper techniques and maneuvers and experiential learning. The novel use for curriculum evaluation may be used to evaluate other courses-especially comprehensive and multicomponent courses.

New model reduction technique for a class of parabolic partial differential equations

NARCIS (Netherlands)

Vajta, Miklos

1991-01-01

A model reduction (or lumping) technique for a class of parabolic-type partial differential equations is given, and its application is discussed. The frequency response of the temperature distribution in any multilayer solid is developed and given by a matrix expression. The distributed transfer

Seismic qualification using digital signal processing/modal testing and finite element techniques

International Nuclear Information System (INIS)

Steedman, J.B.; Edelstein, A.

1983-01-01

A systematic procedure in which digital signal processing, modal testing and finite element techniques can be used to seismically qualify Class IE equipment for use in nuclear generating stations is presented. A new method was also developed in which measured transmissibility functions and Fourier transformation techniques were combined to compute instrument response spectra. As an illustrative example of the qualification method, the paper follows the qualification of a safety related Class IE Heating, Ventilating, and Air Conditioning (HVAC) Control Panel subjected to both seismic and hydrodynamic loading conditions

Response Time Analysis and Test of Protection System Instrument Channels for APR1400 and OPR1000

Energy Technology Data Exchange (ETDEWEB)

Lee, Chang Jae; Han, Seung; Yun, Jae Hee; Baek, Seung Min [Department of Instrumentation and Control System Engineering, KEPCO Engineering and Construction, Daejeon (Korea, Republic of); Lee, Sang Jeong [Department of Electronics Engineering, Chungnam National University, Daejeon (Korea, Republic of)

2015-07-01

Safety limits are required to maintain the integrity of physical barriers designed to prevent the uncontrolled release of radioactive materials in nuclear power plants. The safety analysis establishes two critical constraints that include an analytical limit in terms of a measured or calculated variable, and a specific time after the analytical limit is reached to begin protective action. Keeping with the nuclear regulations and industry standards, satisfying these two requirements will ensure that the safety limit will not be exceeded during the design basis event, either an anticipated operational occurrence or a postulated accident. Various studies on the setpoint determination methodology for the safety-related instrumentation have been actively performed to ensure that the requirement of the analytical limit is satisfied. In particular, the protection setpoint methodology for the advanced power reactor 1400 (APP1400) and the optimized power reactor 1000 (OPR1000) has been recently developed to cover both the design basis event and the beyond design basis event. The developed setpoint methodology has also been quantitatively validated using specific computer programs and setpoint calculations. However, the safety of nuclear power plants cannot be fully guaranteed by satisfying the requirement of the analytical limit. In spite of the response time verification requirements of nuclear regulations and industry standards, it is hard to find the studies on the systematically integrated methodology regarding the response time evaluation. In cases of APR1400 and OPR1000, the response time analysis for the plant protection system is partially included in the setpoint calculation and the response time test is separately performed via the specific plant procedure. The test technique has a drawback which is the difficulty to demonstrate completeness of timing test. The analysis technique has also a demerit of resulting in extreme times that not actually possible. Thus

Response Time Analysis and Test of Protection System Instrument Channels for APR1400 and OPR1000

International Nuclear Information System (INIS)

Lee, Chang Jae; Han, Seung; Yun, Jae Hee; Baek, Seung Min; Lee, Sang Jeong

2015-01-01

Safety limits are required to maintain the integrity of physical barriers designed to prevent the uncontrolled release of radioactive materials in nuclear power plants. The safety analysis establishes two critical constraints that include an analytical limit in terms of a measured or calculated variable, and a specific time after the analytical limit is reached to begin protective action. Keeping with the nuclear regulations and industry standards, satisfying these two requirements will ensure that the safety limit will not be exceeded during the design basis event, either an anticipated operational occurrence or a postulated accident. Various studies on the setpoint determination methodology for the safety-related instrumentation have been actively performed to ensure that the requirement of the analytical limit is satisfied. In particular, the protection setpoint methodology for the advanced power reactor 1400 (APP1400) and the optimized power reactor 1000 (OPR1000) has been recently developed to cover both the design basis event and the beyond design basis event. The developed setpoint methodology has also been quantitatively validated using specific computer programs and setpoint calculations. However, the safety of nuclear power plants cannot be fully guaranteed by satisfying the requirement of the analytical limit. In spite of the response time verification requirements of nuclear regulations and industry standards, it is hard to find the studies on the systematically integrated methodology regarding the response time evaluation. In cases of APR1400 and OPR1000, the response time analysis for the plant protection system is partially included in the setpoint calculation and the response time test is separately performed via the specific plant procedure. The test technique has a drawback which is the difficulty to demonstrate completeness of timing test. The analysis technique has also a demerit of resulting in extreme times that not actually possible. Thus

Switchable and responsive surfaces and materials for biomedical applications

CERN Document Server

Zhang, Johnathan

2015-01-01

Surface modification of biomaterials can ultimately determine whether a material is accepted or rejected from the human body, and a responsive surface can further make the material ""smart"" and ""intelligent"". Switchable and Responsive Surfaces and Materials for Biomedical Applications outlines synthetic and biological materials that are responsive under different stimuli, their surface design and modification techniques, and applicability in regenerative medicine/tissue engineering,  drug delivery, medical devices, and biomedical diagnostics. Part one provides a detailed overview of swit

Improving skill development: an exploratory study comparing a philosophical and an applied ethical analysis technique

Science.gov (United States)

Al-Saggaf, Yeslam; Burmeister, Oliver K.

2012-09-01

This exploratory study compares and contrasts two types of critical thinking techniques; one is a philosophical and the other an applied ethical analysis technique. The two techniques analyse an ethically challenging situation involving ICT that a recent media article raised to demonstrate their ability to develop the ethical analysis skills of ICT students and professionals. In particular the skill development focused on includes: being able to recognise ethical challenges and formulate coherent responses; distancing oneself from subjective judgements; developing ethical literacy; identifying stakeholders; and communicating ethical decisions made, to name a few.

Application of fisheries management techniques to assessing impacts: task I report

International Nuclear Information System (INIS)

McKenzie, D.H.; Baker, K.S.; Fickeisen, D.H.; Metzger, R.M.; Skalski, J.R.

1979-03-01

Task I efforts examined the available fisheries management techniques and assessed their potential application in a confirmatory monitoring program. The objective of such monitoring programs is to confirm that the prediction of an insignificant impact (usually made in the FES) was correct. Fisheries resource managers have developed several tools for assessing the fish population response to stress (exploitation) and they were thought potentially useful for detecting nuclear power plant impacts. Techniques in three categories were examined; catch removal, population dynamics, and nondestructive censuses, and the report contains their description, examples of application, advantages, and disadvantages. The techniques applied at nuclear power plant sites were examined in detail to provide information on implementation and variability of specific approaches. The most suitable techniques to incorporate into a monitoring program confirming no impact appear to be those based on Catch Per Unity Effort (CPUE) and hydroacoustic data. In some specific cases, age and growth studies and indirect census techniques may be beneficial. Recommendations for task II efforts to incorporate these techniques into monitoring program designs are presented. These include development of guidelines for; (1) designing and implementing a data collection program; (2) interpreting these data and assessing the occurrence of impact, and (3) establishment of the monitoring program's ability to detect changes in the affected populations

Collimator performance evaluation by Monte-Carlo techniques

International Nuclear Information System (INIS)

Milanesi, L.; Bettinardi, V.; Bellotti, E.; Gilardi, M.C.; Todd-Pokropek, A.; Fazio, F.

1985-01-01

A computer program using Monte-Carlo techniques has been developed to simulate gamma camera collimator performance. Input data include hole length, septum thickness, hole size and shape, collimator material, source characteristics, source to collimator distance and medium, radiation energy, total events number. Agreement between Monte-Carlo simulations and experimental measurements was found for commercial hexagonal parallel hole collimators in terms of septal penetration, transfer function and sensitivity. The method was then used to rationalize collimator design for tomographic brain studies. A radius of ration of 15 cm was assumed. By keeping constant resolution at 15 cm (FWHM = 1.3.cm), SPECT response to a point source was obtained in scattering medium for three theoretical collimators. Sensitivity was maximized in the first collimator, uniformity of resolution response in the third, while the second represented a trade-off between the two. The high sensitivity design may be superior in the hot spot and/or low activity situation, while for distributed sources of high activity an uniform resolution response should be preferred. The method can be used to personalize collimator design to different clinical needs in SPECT

Can cognitive processes help explain the success of instructional techniques recommended by behavior analysts?

Science.gov (United States)

Markovits, Rebecca A.; Weinstein, Yana

2018-01-01

The fields of cognitive psychology and behavior analysis have undertaken separate investigations into effective learning strategies. These studies have led to several recommendations from both fields regarding teaching techniques that have been shown to enhance student performance. While cognitive psychology and behavior analysis have studied student performance independently from their different perspectives, the recommendations they make are remarkably similar. The lack of discussion between the two fields, despite these similarities, is surprising. The current paper seeks to remedy this oversight in two ways: first, by reviewing two techniques recommended by behavior analysts—guided notes and response cards—and comparing them to their counterparts in cognitive psychology that are potentially responsible for their effectiveness; and second, by outlining some other areas of overlap that could benefit from collaboration. By starting the discussion with the comparison of two specific recommendations for teaching techniques, we hope to galvanize a more extensive collaboration that will not only further the progression of both fields, but also extend the practical applications of the ensuing research.

Dynamic Deformation Behavior of Soft Material Using Shpb Technique and Pulse Shaper

Science.gov (United States)

Lee, Ouk Sub; Cho, Kyu Sang; Kim, Sung Hyun; Han, Yong Hwan

This paper presents a modified Split Hopkinson Pressure Bar (SHPB) technique to obtain compressive stress strain data for NBR rubber materials. An experimental technique with a modified the conventional SHPB has been developed for measuring the compressive stress strain responses of materials with low mechanical impedance and low compressive strengths, such as the rubber and the polymeric material. This paper uses an aluminum pressure bar to achieve a closer impedance match between the pressure bar and the specimen materials. In addition, a pulse shaper is utilized to lengthen the rising time of the incident pulse to ensure dynamic stress equilibrium and homogeneous deformation of NBR rubber materials. It is found that the modified technique can determine the dynamic deformation behavior of rubbers more accurately.

Metabolic mapping of functional activity in human subjects with the [18F]fluorodeoxyglucose technique

International Nuclear Information System (INIS)

Greenberg, J.H.; Reivich, M.; Alavi, A.

1981-01-01

The 2-[ 18 F]fluoro-2-deoxy-D-glucose technique was used to measure regional cerebral glucose utilization by human subjects during functional activation. Normal male volunteers subjected to one or more sensory stimuli exhibited focal increases in glucose metabolism in response to the stimulus. These results demonstrate that the technique is capable of providing functional maps in vivo related to both body region and submodality of sensory information in the human brain

Dynamic characterization of satellite assembly for responsive space applications

International Nuclear Information System (INIS)

Mascarenas, David; Macknelly, David; Mullins, Josh; Wiest, Heather; Park, Gyuhae

2013-01-01

The rapid deployment of satellites for responsive space surveillance applications is hindered by the need to flight-qualify their components and the resulting mechanical assembly. Conventional methods for qualification testing of satellite components are costly and time consuming. Furthermore, full-scale vehicles must be subjected to simulated launch loads during testing, and this harsh testing environment increases the risk of damage to satellite components during qualification. This work focuses on replacing this potentially destructive testing procedure with a non-destructive structural health monitoring (SHM)-based technique while maintaining the same level of confidence in the testing procedure's ability to qualify the satellite for flight. We focus on assessing the performance of SHM techniques to replace the high-cost qualification procedure and to localize faults introduced by improper assembly. The goal of this work is to create a dual-use system that can both assist in the process of qualifying the satellite for launch, as well as provide continuous structural integrity monitoring during manufacture, transport, launch and deployment. SHM techniques were applied on a small-scale structure representative of a responsive satellite. The test structure consisted of an extruded aluminum space-frame covered with aluminum shear plates assembled using bolted joints. Multiple piezoelectric transducers were bonded to the test structure and acted as combined actuators and sensors. Piezoelectric active-sensing based techniques, including measurements of low-frequency global frequency response functions and high-frequency wave propagation techniques, were employed. Using these methods in conjunction with finite element modeling, the dynamic properties of the test structure were established and areas of potential damage could be identified and localized. A procedure for guiding the effective placement of the sensors and actuators is also outlined. (paper)

Surface science techniques

CERN Document Server

Bracco, Gianangelo

2013-01-01

The book describes the experimental techniques employed to study surfaces and interfaces. The emphasis is on the experimental method. Therefore all chapters start with an introduction of the scientific problem, the theory necessary to understand how the technique works and how to understand the results. Descriptions of real experimental setups, experimental results at different systems are given to show both the strength and the limits of the technique. In a final part the new developments and possible extensions of the techniques are presented. The included techniques provide microscopic as well as macroscopic information. They cover most of the techniques used in surface science.

Dosimetric characterization of BeO samples in alpha, beta and X radiation beams using luminescent techniques

International Nuclear Information System (INIS)

Groppo, Daniela Piai

2013-01-01

In the medical field, the ionizing radiation is used both for therapeutic and diagnostic purposes, in a wide range of radiation doses. In order to ensure that the objective is achieved in practice, detailed studies of detectors and devices in different types of radiations beams are necessary. In this work a dosimetric characterization of BeO samples was performed using the techniques of thermoluminescence (TL) and optically stimulated luminescence (OSL) by a comparison of their response for alpha, beta and X radiations and the establishment of an appropriated system for use in monitoring of these radiations beams. The main results are: the high sensitivity to beta radiation for both techniques, good reproducibility of TL and OSL response (coefficients of variation lower than 5%), maximum energy dependence of the X radiation of 28% for the TL technique, and only 7% for the OSL technique, within the studied energy range. The dosimetric characteristics obtained in this work show the possibility of applying BeO samples to dosimetry of alpha, beta and X radiations, considering the studied dose ranges, using the TL and OSL techniques. From the results obtained, the samples of BeO showed their potential use for beam dosimetry in diagnostic radiology and radiotherapy. (author)

Fundamentals of functional imaging I: current clinical techniques.

Science.gov (United States)

Luna, A; Martín Noguerol, T; Mata, L Alcalá

2018-05-01

Imaging techniques can establish a structural, physiological, and molecular phenotype for cancer, which helps enable accurate diagnosis and personalized treatment. In recent years, various imaging techniques that make it possible to study the functional characteristics of tumors quantitatively and reproducibly have been introduced and have become established in routine clinical practice. Perfusion studies enable us to estimate the microcirculation as well as tumor angiogenesis and permeability using ultrafast dynamic acquisitions with ultrasound, computed tomography, or magnetic resonance (MR) imaging. Diffusion-weighted sequences now form part of state-of-the-art MR imaging protocols to evaluate oncologic lesions in any anatomic location. Diffusion-weighted imaging provides information about the occupation of the extracellular and extravascular space and indirectly estimates the cellularity and apoptosis of tumors, having demonstrated its relation with biologic aggressiveness in various tumor lines and its usefulness in the evaluation of the early response to systemic and local targeted therapies. Another tool is hydrogen proton MR spectroscopy, which is used mainly in the study of the metabolic characteristics of brain tumors. However, the complexity of the technique and its lack of reproducibility have limited its clinical use in other anatomic areas, although much experience with the use of this technique in the assessment of prostate and breast cancers as well as liver lesions has also accumulated. This review analyzes the imaging techniques that make it possible to evaluate the physiological and molecular characteristics of cancer that have already been introduced into clinical practice, such as techniques that evaluate angiogenesis through dynamic acquisitions after the administration of contrast material, diffusion-weighted imaging, or hydrogen proton MR spectroscopy, as well as their principal applications in oncology. Copyright © 2018 SERAM. Publicado

Onsite nondestructive examination techniques for irradiated water-cooled power reactor fuel

International Nuclear Information System (INIS)

1981-03-01

The International Atomic Energy Agency, in response to the recommendations from several Member States, has prepared this Guidebook on Onsite Non-Destructive Techniques for Irradiated Water-Cooled Power Reactor Fuel with the assistance of a number of experts and organizations in this field. During the preparation of this report it became evident that a comparison between different techniques is a most difficult task and depends on a number of factors related to fuel design, plant characteristics and operating conditions. Consequently the emphasis of the report is on the survey of different techniques presently available. It is also to be noted that because the degree of development for any given technique varies significantly among organizations, it is understood that the report should not be used as consensus standard of the minimum capabilities for each class of techniques, nor does it give recommendations in the regulatory sense. Furthermore, the inclusion of some commercial pieces of equipment, services and other products are for illustrative purposes only and neither implies any preference by the Agency nor can the Agency be liable for any material presented in the report

Space-mapping techniques applied to the optimization of a safety isolating transformer

NARCIS (Netherlands)

T.V. Tran; S. Brisset; D. Echeverria (David); D.J.P. Lahaye (Domenico); P. Brochet

2007-01-01

textabstractSpace-mapping optimization techniques allow to allign low-fidelity and high-fidelity models in order to reduce the computational time and increase the accuracy of the solution. The main idea is to build an approximate model from the difference of response between both models. Therefore

Direct analysis of quantal radiation response data

International Nuclear Information System (INIS)

Thames, H.D. Jr.; Rozell, M.E.; Tucker, S.L.; Ang, K.K.; Travis, E.L.; Fisher, D.R.

1986-01-01

A direct analysis is proposed for quantal (all-or-nothing) responses to fractionated radiation and endpoint-dilution assays of cell survival. As opposed to two-step methods such as the reciprocal-dose technique, in which ED 50 values are first estimated for different fractionation schemes and then fit (as reciprocals) against dose per fraction, all raw data are included in a single maximum-likelihood treatment. The method accommodates variations such as short-interval fractionation regimens designed to determine tissue repair kinetics, tissue response to continuous exposures, and data obtained using endpoint-dilution assays of cell survival after fractionated doses. Monte-Carlo techniques were used to compare the direct and reciprocal-dose methods for analysis of small-scale and large-scale studies of response to fractionated doses. Both methods tended toward biased estimates in the analysis of small-scale (3 fraction numbers) studies. The α/β ratios showed less scatter when estimated by the direct method. The 95% confidence intervals determined by the direct method were more appropriate than those determined by reciprocal-dose analysis, for which 18% (small-scale study) or 8% (large-scale study) of the confidence intervals did not include the 'true' value of α/β. (author)

Application of laser tweezers Raman spectroscopy techniques to the monitoring of single cell response to stimuli

Science.gov (United States)

Chan, James W.; Liu, Rui; Matthews, Dennis L.

2012-06-01

Laser tweezers Raman spectroscopy (LTRS) combines optical trapping with micro-Raman spectroscopy to enable label-free biochemical analysis of individual cells and small biological particles in suspension. The integration of the two technologies greatly simplifies the sample preparation and handling of suspension cells for spectroscopic analysis in physiologically meaningful conditions. In our group, LTRS has been used to study the effects of external perturbations, both chemical and mechanical, on the biochemistry of the cell. Single cell dynamics can be studied by performing longitudinal studies to continuously monitor the response of the cell as it interacts with its environment. The ability to carry out these measurements in-vitro makes LTRS an attractive tool for many biomedical applications. Here, we discuss the use of LTRS to study the response of cancer cells to chemotherapeutics and bacteria cells to antibiotics and show that the life cycle and apoptosis of the cells can be detected. These results show the promise of LTRS for drug discovery/screening, antibiotic susceptibility testing, and chemotherapy response monitoring applications. In separate experiments, we study the response of red blood cells to the mechanical forces imposed on the cell by the optical tweezers. A laser power dependent deoxygenation of the red blood cell in the single beam trap is reported. Normal, sickle cell, and fetal red blood cells have a different behavior that enables the discrimination of the cell types based on this mechanochemical response. These results show the potential utility of LTRS for diagnosing and studying red blood cell diseases.

The transcriptional regulatory network in the drought response and its crosstalk in abiotic stress responses including drought, cold, and heat

OpenAIRE

Nakashima, Kazuo; Yamaguchi-Shinozaki, Kazuko; Shinozaki, Kazuo

2014-01-01

Drought negatively impacts plant growth and the productivity of crops around the world. Understanding the molecular mechanisms in the drought response is important for improvement of drought tolerance using molecular techniques. In plants, abscisic acid (ABA) is accumulated under osmotic stress conditions caused by drought, and has a key role in stress responses and tolerance. Comprehensive molecular analyses have shown that ABA regulates the expression of many genes under osmotic stress cond...

A minimax technique for time-domain design of preset digital equalizers using linear programming

Science.gov (United States)

Vaughn, G. L.; Houts, R. C.

1975-01-01

A linear programming technique is presented for the design of a preset finite-impulse response (FIR) digital filter to equalize the intersymbol interference (ISI) present in a baseband channel with known impulse response. A minimax technique is used which minimizes the maximum absolute error between the actual received waveform and a specified raised-cosine waveform. Transversal and frequency-sampling FIR digital filters are compared as to the accuracy of the approximation, the resultant ISI and the transmitted energy required. The transversal designs typically have slightly better waveform accuracy for a given distortion; however, the frequency-sampling equalizer uses fewer multipliers and requires less transmitted energy. A restricted transversal design is shown to use the least number of multipliers at the cost of a significant increase in energy and loss of waveform accuracy at the receiver.

Process sensors characterization based on noise analysis technique and artificial intelligence

International Nuclear Information System (INIS)

Mesquita, Roberto N. de; Perillo, Sergio R.P.; Santos, Roberto C. dos

2005-01-01

The time response of pressure and temperature sensors from the Reactor Protection System (RPS) is a requirement that must be satisfied in nuclear power plants, furthermore is an indicative of its degradation and its remaining life. The nuclear power industry and others have been eager to implement smart sensor technologies and digital instrumentation concepts to reduce manpower and effort currently spent on testing and calibration. Process parameters fluctuations during normal operation of a reactor are caused by random variations in neutron flux, heat transfer and other sources. The output sensor noise can be considered as the response of the system to an input representing the statistical nature of the underlying process which can be modeled using a time series model. Since the noise signal measurements are influenced by many factors, such as location of sensors, extraneous noise interference, and randomness in temperature and pressure fluctuation - the quantitative estimate of the time response using autoregressive noise modeling is subject to error. This technique has been used as means of sensor monitoring. In this work a set of pressure sensors installed in one experimental loop adapted from a flow calibration setup is used to test and analyze signals in a new approach using artificial intelligence techniques. A set of measurements of dynamic signals in different experimental conditions is used to distinguish and identify underlying process sources. A methodology that uses Blind Separation of Sources with a neural networks scheme is being developed to improve time response estimate reliability in noise analysis. (author)

Process sensors characterization based on noise analysis technique and artificial intelligence

Energy Technology Data Exchange (ETDEWEB)

Mesquita, Roberto N. de; Perillo, Sergio R.P.; Santos, Roberto C. dos [Instituto de Pesquisas Energeticas e Nucleares (IPEN), Sao Paulo, SP (Brazil)]. E-mail: rnavarro@ipen.br; sperillo@ipen.br; rcsantos@ipen.br

2005-07-01

The time response of pressure and temperature sensors from the Reactor Protection System (RPS) is a requirement that must be satisfied in nuclear power plants, furthermore is an indicative of its degradation and its remaining life. The nuclear power industry and others have been eager to implement smart sensor technologies and digital instrumentation concepts to reduce manpower and effort currently spent on testing and calibration. Process parameters fluctuations during normal operation of a reactor are caused by random variations in neutron flux, heat transfer and other sources. The output sensor noise can be considered as the response of the system to an input representing the statistical nature of the underlying process which can be modeled using a time series model. Since the noise signal measurements are influenced by many factors, such as location of sensors, extraneous noise interference, and randomness in temperature and pressure fluctuation - the quantitative estimate of the time response using autoregressive noise modeling is subject to error. This technique has been used as means of sensor monitoring. In this work a set of pressure sensors installed in one experimental loop adapted from a flow calibration setup is used to test and analyze signals in a new approach using artificial intelligence techniques. A set of measurements of dynamic signals in different experimental conditions is used to distinguish and identify underlying process sources. A methodology that uses Blind Separation of Sources with a neural networks scheme is being developed to improve time response estimate reliability in noise analysis. (author)

Inverse Optimization and Forecasting Techniques Applied to Decision-making in Electricity Markets

DEFF Research Database (Denmark)

Saez Gallego, Javier

patterns that the load traditionally exhibited. On the other hand, this thesis is motivated by the decision-making processes of market players. In response to these challenges, this thesis provides mathematical models for decision-making under uncertainty in electricity markets. Demand-side bidding refers......This thesis deals with the development of new mathematical models that support the decision-making processes of market players. It addresses the problems of demand-side bidding, price-responsive load forecasting and reserve determination. From a methodological point of view, we investigate a novel...... approach to model the response of aggregate price-responsive load as a constrained optimization model, whose parameters are estimated from data by using inverse optimization techniques. The problems tackled in this dissertation are motivated, on one hand, by the increasing penetration of renewable energy...

Peritoneal dialysis technique success during the initial 90 days of therapy.

Science.gov (United States)

Guest, Steven; Hayes, Andrew C; Story, Kenneth; Davis, Ira D

2012-01-01

Comparisons of technique success by peritoneal dialysis (PD) modality have typically excluded the initial 90 days of therapy. We analyzed a database of 51,469 new PD starts from 2004 to 2008 in the United States. The analysis concentrated on the initial 90 days of therapy to determine technique success and the impact of the continuous ambulatory PD (CAPD) and automated PD (APD) modalities. Overall, 13.3% of patients stopped PD within 90 days. Of patients starting directly on APD, 14.3% stopped PD within 90 days. Of patients starting on CAPD, 12.6% stopped PD within 90 days, and 63.4% changed to APD within 90 days. Only 3.3% of the latter patients failed to reach 90 days of therapy. By comparison, technique failure occurred in 28.8% of those initiating with and remaining on CAPD. We conclude that initial training to perform CAPD, with timely transfer to APD within the first 3 months, was associated with the greatest technique success at 90 days. The reasons for that success are unclear, and further research should be directed to determining factors responsible. It is possible that patients trained initially to CAPD but converted to APD have a greater understanding of the total therapy, which improves confidence. Those converted to APD may be more appreciative of the lifestyle benefits of APD, which translates into improved compliance; alternatively, technical factors associated with APD may be responsible. Those technical factors may include improved catheter function in the recumbent position during APD or the reduced infection risk associated with just 2 connect/disconnect procedures in APD compared with 8 in CAPD.

CRYOTHERAPY: A NEW TECHNIQUE TO OBTAIN GRAPEVINE PLANTS FREE OF VIRUSES

Directory of Open Access Journals (Sweden)

JEAN CARLOS BETTONI

2016-01-01

Full Text Available ABSTRACT Through in vitro tissue culture techniques it is possible to propagate high quality nursery plants faster. Cryotherapy is a promising tool, based on in vitro culture techniques, for achieving in a short time, high frequency of regenerating plants free of viruses. The objective of this review is to present and analyze the results of research conducted in cryotherapy methods based on cryopreservation protocols for recovery of cultivars free of micro-organisms with potential agronomic interest. The main methods employed in cryotherapy are encapsulation-dehydration, vitrification, encapsulation-vitrification and droplet vitrification, which are based on the immersion of preconditioned shoot tips in liquid nitrogen, followed by their recovery in vitro on to culture media for regeneration of healthy plantlets. Improvements to cryotherapy protocols used for grapevine are still needed, since there are variations in response according to the genotype. The published research mostly relates to Vitis vinifera and the few studies applied to other species show that the protocols need to be improved. This specificity goes beyond species, with different responses among cultivars, limiting the broader application of the technology. On the other hand, traditional methods used for virus removal from infected plant materials also have limitations and therefore investment in research for the development and application of cryopreservation techniques is highly justified, considering its efficiency and low-cost, once the protocols are developed. High frequency of virus-free plants among regenerants within a short time frame is the most desirable aspect of cryotherapy. Therefore, these advantages make the technique a promising tool for institutions mandated to the development of high-health planting materials with high genetic and agronomic potential for viticulture.

Spike latency and response properties of an excitable micropillar laser

Science.gov (United States)

Selmi, F.; Braive, R.; Beaudoin, G.; Sagnes, I.; Kuszelewicz, R.; Erneux, T.; Barbay, S.

2016-10-01

We present experimental measurements concerning the response of an excitable micropillar laser with saturable absorber to incoherent as well as coherent perturbations. The excitable response is similar to the behavior of spiking neurons but with much faster time scales. It is accompanied by a subnanosecond nonlinear delay that is measured for different bias pump values. This mechanism provides a natural scheme for encoding the strength of an ultrafast stimulus in the response delay of excitable spikes (temporal coding). Moreover, we demonstrate coherent and incoherent perturbations techniques applied to the micropillar with perturbation thresholds in the range of a few femtojoules. Responses to coherent perturbations assess the cascadability of the system. We discuss the physical origin of the responses to single and double perturbations with the help of numerical simulations of the Yamada model and, in particular, unveil possibilities to control the relative refractory period that we recently evidenced in this system. Experimental measurements are compared to both numerical simulations of the Yamada model and analytic expressions obtained in the framework of singular perturbation techniques. This system is thus a good candidate to perform photonic spike processing tasks in the framework of novel neuroinspired computing systems.

Modeling of an Aged Porous Silicon Humidity Sensor Using ANN Technique

Directory of Open Access Journals (Sweden)

Tarikul ISLAM

2006-10-01

Full Text Available Porous silicon (PS sensor based on capacitive technique used for measuring relative humidity has the advantages of low cost, ease of fabrication with controlled structure and CMOS compatibility. But the response of the sensor is nonlinear function of humidity and suffers from errors due to aging and stability. One adaptive linear (ADALINE ANN model has been developed to model the behavior of the sensor with a view to estimate these errors and compensate them. The response of the sensor is represented by third order polynomial basis function whose coefficients are determined by the ANN technique. The drift in sensor output due to aging of PS layer is also modeled by adapting the weights of the polynomial function. ANN based modeling is found to be more suitable than conventional physical modeling of PS humidity sensor in changing environment and drift due to aging. It helps online estimation of nonlinearity as well as monitoring of the fault of the PS humidity sensor using the coefficients of the model.

Innovative Concepts and Operational Techniques for the Strategic National Stockpile

International Nuclear Information System (INIS)

Adams, S. A.

2007-01-01

This presentation is to discuss the innovative concepts and operational techniques developed by the Center for Disease Control and Prevention's Division of Strategic National Stockpile (DSNS). The primary response model for the SNS is to move from secure strategic storage locations to an area of need within 12 hours to augment local resources. While this 12 hour response is appropriate for most threat scenarios, it clearly cannot meet the needs of first line responders who need to rapidly administer initial dosing of nerve agent antidote. To address the threat of nerve agent poisoning the DSNS developed the CHEMPACK Project which allows centralized SNS management forward placement within hundreds of local jurisdictions. Another variation from the primary mission of the DSNS is addressing the nation's potential shortfall in non-acute care bed capacity. To address this mission, the Federal Medical Station (FMS) program was created to build surge capability to meet a range of non-acute medical needs following a disaster. The FMS model is a pre-configured 250 bed unit that is deployable throughout the Nation and configured to respond rapidly. Operational techniques used to maximize product lifespan and efficacy will also be discussed.(author)

Constructed-Response Matching to Sample and Spelling Instruction.

Science.gov (United States)

Dube, William V.; And Others

1991-01-01

This paper describes a computer-based spelling program grounded in programed instructional techniques and using constructed-response matching-to-sample procedures. Following use of the program, two mentally retarded men successfully spelled previously misspelled words. (JDD)

The application of radiobiological study by gene chip technique

International Nuclear Information System (INIS)

Li Yu; Li Yao

2002-01-01

The responses to ionizing radiation are complex and are regulated by a number of overlapping molecular pathways. One such stress-signaling pathway involves p53, which regulates the expression of over 100 genes already identified. It is also becoming increasingly apparent that the pattern of stress gene expression has some cell type specificity. It may be possible to exploit these differences in stress gene responsiveness as molecular markers through the use of a combined informatics and functional genomic approach. The techniques of micro-array analysis potentially offer the opportunity to monitor changes in gene expression across the entire set of expressed genes in a cell or organism. It again highlights the importance of a cellular context to genotoxic stress responses; it also raises the prospect of expression profiling of cell lines, tissues, and tumors. Such profiles may have a predictive value in cancer therapy regimens, or identification of exposures to environmental toxins

The analysis of public relations role in improving corporate social responsibility

Directory of Open Access Journals (Sweden)

Đervida-Lekanić Ružica

2016-01-01

Full Text Available The main objective of modern business is achievement of business excellence and world-class of products and services. Companies which actively and continuously apply modern management methods and techniques, especially in marketing, have significantly better chance to strengthen their competitive capability on global market and to assume stable market position with perspective for further market development. Modern business philosophy implies that organization has to be responsible for its actions and steps towards all stakeholders in the environment. Attaining of business excellence goals of an organization presupposes built corporate social responsibility. The research results presented in this paper were used to analyze the possibilities of using modern methods and techniques of public relations in business organizations and improve corporate social responsibility on the market of Bosnia and Herzegovina.

Flowing dusty plasma experiments: generation of flow and measurement techniques

Science.gov (United States)

Jaiswal, S.; Bandyopadhyay, P.; Sen, A.

2016-12-01

A variety of experimental techniques for the generation of subsonic/supersonic dust fluid flows and means of measuring such flow velocities are presented. The experiments have been carried out in a \\Pi -shaped dusty plasma experimental device with micron size kaolin/melamine formaldehyde particles embedded in a background of argon plasma created by a direct current glow discharge. A stationary dust cloud is formed over the cathode region by precisely balancing the pumping speed and gas flow rate. A flow of dust particles/fluid is generated by additional gas injection from a single or dual locations or by altering the dust confining potential. The flow velocity is then estimated by three different techniques, namely, by super particle identification code, particle image velocimetry analysis and the excitation of dust acoustic waves. The results obtained from these three different techniques along with their merits and demerits are discussed. An estimation of the neutral drag force responsible for the generation as well as the attenuation of the dust fluid flow is made. These techniques can be usefully employed in laboratory devices to investigate linear and non-linear collective excitations in a flowing dusty plasma.

Detection of drugs and explosives using neutron computerized tomography and artificial intelligence techniques

Energy Technology Data Exchange (ETDEWEB)

Ferreira, F.J.O. [Instituto de Engenharia Nuclear, Cidade Universitaria, Rio de Janeiro, CEP 21945-970, Caixa Postal 68550 (Brazil)], E-mail: fferreira@ien.gov.br; Crispim, V.R.; Silva, A.X. [DNC/Poli, PEN COPPE CT, UFRJ Universidade Federal do Rio de Janeiro, CEP 21941-972, Caixa Postal 68509, Rio de Janeiro (Brazil)

2010-06-15

In this study the development of a methodology to detect illicit drugs and plastic explosives is described with the objective of being applied in the realm of public security. For this end, non-destructive assay with neutrons was used and the technique applied was the real time neutron radiography together with computerized tomography. The system is endowed with automatic responses based upon the application of an artificial intelligence technique. In previous tests using real samples, the system proved capable of identifying 97% of the inspected materials.

Detection of drugs and explosives using neutron computerized tomography and artificial intelligence techniques

International Nuclear Information System (INIS)

Ferreira, F.J.O.; Crispim, V.R.; Silva, A.X.

2010-01-01

In this study the development of a methodology to detect illicit drugs and plastic explosives is described with the objective of being applied in the realm of public security. For this end, non-destructive assay with neutrons was used and the technique applied was the real time neutron radiography together with computerized tomography. The system is endowed with automatic responses based upon the application of an artificial intelligence technique. In previous tests using real samples, the system proved capable of identifying 97% of the inspected materials.

Modeling the Structural Response of Reinforced Glass Beams using an SLA Scheme

NARCIS (Netherlands)

Louter, P.C.; Graaf, van de Anne; Rots, J.G.; Bos, Freek; Louter, Pieter Christiaan; Veer, Fred

2010-01-01

This paper investigates whether a novel computational sequentially linear analysis (SLA) technique, which is especially developed for modeling brittle material response, is applicable for modeling the structural response of metal reinforced glass beams. To do so, computational SLA results are

Data-Driven Optimization of Incentive-based Demand Response System with Uncertain Responses of Customers

Directory of Open Access Journals (Sweden)

Jimyung Kang

2017-10-01

Full Text Available Demand response is nowadays considered as another type of generator, beyond just a simple peak reduction mechanism. A demand response service provider (DRSP can, through its subcontracts with many energy customers, virtually generate electricity with actual load reduction. However, in this type of virtual generator, the amount of load reduction includes inevitable uncertainty, because it consists of a very large number of independent energy customers. While they may reduce energy today, they might not tomorrow. In this circumstance, a DSRP must choose a proper set of these uncertain customers to achieve the exact preferred amount of load curtailment. In this paper, the customer selection problem for a service provider that consists of uncertain responses of customers is defined and solved. The uncertainty of energy reduction is fully considered in the formulation with data-driven probability distribution modeling and stochastic programming technique. The proposed optimization method that utilizes only the observed load data provides a realistic and applicable solution to a demand response system. The performance of the proposed optimization is verified with real demand response event data in Korea, and the results show increased and stabilized performance from the service provider’s perspective.

Assessing the response to targeted therapies in renal cell carcinoma: technical insights and practical considerations.

Science.gov (United States)

Bex, Axel; Fournier, Laure; Lassau, Nathalie; Mulders, Peter; Nathan, Paul; Oyen, Wim J G; Powles, Thomas

2014-04-01

The introduction of targeted agents for the treatment of renal cell carcinoma (RCC) has resulted in new challenges for assessing response to therapy, and conventional response criteria using computed tomography (CT) are limited. It is widely recognised that targeted therapies may lead to significant necrosis without significant reduction in tumour size. In addition, the vascular effects of antiangiogenic therapy may occur long before there is any reduction in tumour size. To perform a systematic review of conventional and novel imaging methods for the assessment of response to targeted agents in RCC and to discuss their use from a clinical perspective. Relevant databases covering the period January 2006 to April 2013 were searched for studies reporting on the use of anatomic and functional imaging techniques to predict response to targeted therapy in RCC. Inclusion criteria were randomised trials, nonrandomised controlled studies, retrospective case series, and cohort studies. Reviews, animal and preclinical studies, case reports, and commentaries were excluded. A narrative synthesis of the evidence is presented. A total of 331 abstracts and 76 full-text articles were assessed; 34 studies met the inclusion criteria. Current methods of response assessment in RCC include anatomic methods--based on various criteria including Choi, size and attenuation CT, and morphology, attenuation, size, and structure--and functional techniques including dynamic contrast-enhanced (DCE) CT, DCE-magnetic resonance imaging, DCE-ultrasonography, positron emission tomography, and approaches utilising radiolabelled monoclonal antibodies. Functional imaging techniques are promising surrogate biomarkers of response in RCC and may be more appropriate than anatomic CT-based methods. By enabling quantification of tumour vascularisation, functional techniques can directly and rapidly detect the biologic effects of antiangiogenic therapies compared with the indirect detection of belated effects

Decomposition techniques

Science.gov (United States)

Chao, T.T.; Sanzolone, R.F.

1992-01-01

Sample decomposition is a fundamental and integral step in the procedure of geochemical analysis. It is often the limiting factor to sample throughput, especially with the recent application of the fast and modern multi-element measurement instrumentation. The complexity of geological materials makes it necessary to choose the sample decomposition technique that is compatible with the specific objective of the analysis. When selecting a decomposition technique, consideration should be given to the chemical and mineralogical characteristics of the sample, elements to be determined, precision and accuracy requirements, sample throughput, technical capability of personnel, and time constraints. This paper addresses these concerns and discusses the attributes and limitations of many techniques of sample decomposition along with examples of their application to geochemical analysis. The chemical properties of reagents as to their function as decomposition agents are also reviewed. The section on acid dissolution techniques addresses the various inorganic acids that are used individually or in combination in both open and closed systems. Fluxes used in sample fusion are discussed. The promising microwave-oven technology and the emerging field of automation are also examined. A section on applications highlights the use of decomposition techniques for the determination of Au, platinum group elements (PGEs), Hg, U, hydride-forming elements, rare earth elements (REEs), and multi-elements in geological materials. Partial dissolution techniques used for geochemical exploration which have been treated in detail elsewhere are not discussed here; nor are fire-assaying for noble metals and decomposition techniques for X-ray fluorescence or nuclear methods be discussed. ?? 1992.

Recovery of material parameters of soft hyperelastic tissue by an inverse spectral technique

KAUST Repository

Gou, Kun

2012-07-01

An inverse spectral method is developed for recovering a spatially inhomogeneous shear modulus for soft tissue. The study is motivated by a novel use of the intravascular ultrasound technique to image arteries. The arterial wall is idealized as a nonlinear isotropic cylindrical hyperelastic body. A boundary value problem is formulated for the response of the arterial wall within a specific class of quasistatic deformations reflective of the response due to imposed blood pressure. Subsequently, a boundary value problem is developed via an asymptotic construction modeling intravascular ultrasound interrogation which generates small amplitude, high frequency time harmonic vibrations superimposed on the static finite deformation. This leads to a system of second order ordinary Sturm-Liouville boundary value problems that are then employed to reconstruct the shear modulus through a nonlinear inverse spectral technique. Numerical examples are demonstrated to show the viability of the method. © 2012 Elsevier Ltd. All rights reserved.

Using random response input in Ibrahim Time Domain

DEFF Research Database (Denmark)

Olsen, Peter; Brincker, R.

2013-01-01

In this paper the time domain technique Ibrahim Time Domain (ITD) is used to analyze random time data. ITD is known to be a technique for identification of output only systems. The traditional formulation of ITD is claimed to be limited, when identifying closely spaced modes, because....... In this article it is showed that when using the modified ITD random time data can be analyzed. The application of the technique is displayed by a case study, with simulations and experimental data....... of the technique being Single Input Multiple Output (SIMO). It has earlier been showed that when modifying ITD with Toeplitz matrix averaging. Identification of time data with closely spaced modes is improved. In the traditional formulation of ITD the time data has to be free decays or impulse response functions...

Terahertz-frequency dielectric response of liquids

DEFF Research Database (Denmark)

Jepsen, Peter Uhd; Møller, Uffe; Cooke, David

The dielectric response of liquids spans many decades in frequency. The dielectric response of a polar liquid is typically determined by relaxational dynamics of the dipolar moments of the liquid. In contrast, the dielectric response of a nonpolar liquid is determined by much weaker collision......-induced dipole moments. In the polar liquid water the fastest relaxational dynamics is found at terahertz frequencies, just below the first intermolecular vibrational and librational modes. In this presentation we will discuss optical terahertz spectroscopic techniques for measurement of the full dielectric...... function of liquids at terahertz frequencies. We will review the current understanding of the high-frequency dielectric spectrum of water, and discuss the relation between the dielectric spectrum and the thermodynamic properties of certain aqueous solutions....

A Hilbert transform method for parameter identification of time-varying structures with observer techniques

International Nuclear Information System (INIS)

Wang, Zuo-Cai; Ren, Wei-Xin; Chen, Gen-Da

2012-01-01

This paper presents a recursive Hilbert transform method for the time-varying property identification of large-scale shear-type buildings with limited sensor deployments. An observer technique is introduced to estimate the building responses from limited available measurements. For an n-story shear-type building with l measurements (l ≤ n), the responses of other stories without measurements can be estimated based on the first r mode shapes (r ≤ l) as-built conditions and l measurements. Both the measured responses and evaluated responses and their Hilbert transforms are then used to track any variation of structural parameters of a multi-story building over time. Given floor masses, both the stiffness and damping coefficients of the building are identified one-by-one from the top to the bottom story. When variations of parameters are detected, a new developed branch-and-bound technique can be used to update the first r mode shapes with the identified parameters. A 60-story shear building with abruptly varying stiffness at different floors is simulated as an example. The numerical results indicate that the proposed method can detect variations of the parameters of large-scale shear-type buildings with limited sensor deployments at appropriate locations. (paper)

Progress in diagnostic techniques for SC [superconducting] cavities

International Nuclear Information System (INIS)

Reece, C.E.

1988-01-01

Despite the very real progress that has been made, the routine performance of superconducting cavities still falls far short of both the theoretical expectations and the performance of afew exceptional examples. It is the task of systematically applied diagnostic techniques to reveal additional information concerning the response of superconducting surfaces to applied RF fields. In this paper we will direct our attention to discussions of recent developments in diagnostic techniqeus, such as thermometry in superfluid helium, and scanning laser acoustic microscopy. 18 refs., 12 figs

Fuzzy Controller Design Using Evolutionary Techniques for Twin Rotor MIMO System: A Comparative Study

Directory of Open Access Journals (Sweden)

H. A. Hashim

2015-01-01

Full Text Available This paper presents a comparative study of fuzzy controller design for the twin rotor multi-input multioutput (MIMO system (TRMS considering most promising evolutionary techniques. These are gravitational search algorithm (GSA, particle swarm optimization (PSO, artificial bee colony (ABC, and differential evolution (DE. In this study, the gains of four fuzzy proportional derivative (PD controllers for TRMS have been optimized using the considered techniques. The optimization techniques are developed to identify the optimal control parameters for system stability enhancement, to cancel high nonlinearities in the model, to reduce the coupling effect, and to drive TRMS pitch and yaw angles into the desired tracking trajectory efficiently and accurately. The most effective technique in terms of system response due to different disturbances has been investigated. In this work, it is observed that GSA is the most effective technique in terms of solution quality and convergence speed.

Characterizing root response phenotypes by neural network analysis

OpenAIRE

Hatzig, Sarah V.; Schiessl, Sarah; Stahl, Andreas; Snowdon, Rod J.

2015-01-01

Roots play an immediate role as the interface for water acquisition. To improve sustainability in low-water environments, breeders of major crops must therefore pay closer attention to advantageous root phenotypes; however, the complexity of root architecture in response to stress can be difficult to quantify. Here, the Sholl method, an established technique from neurobiology used for the characterization of neural network anatomy, was adapted to more adequately describe root responses to osm...

TEACHING SPEAKING THROUGH THE IMPLEMENTATION OF STORY TELLING TECHNIQUE BY USING STORY-TELLING

Directory of Open Access Journals (Sweden)

Purwatiningsih Purwatiningsih

2015-12-01

Full Text Available Learning a language especially English is expected to help students to be able to use it as a means of communication. Communicating is understanding and expressing information, thought and feeling, and expanding science, technology and culture. Communicating ability means being able to understand a discourse, namely being able to understand and produce spoken and written texts through the four language skills: listening, speaking, reading and writing this classroom action research was conducted to solve the students’ problems in speaking. It is to improve the students’ ability in speaking through story-telling technique using picture series in terms of content and delivery of the story. The design of this study is classroom action research which was conducted in two cycles consisting of six meetings. The subjects of this study were students of grade x-9 of MAN 2 Madiun in 2012/2013 academic year. The instruments to collect the data were observation checklists, field notes, speaking task measured using scoring rubrics, and questionnaire. The criteria of success were determined on the basis of the students’ participation in the teaching-learning process, the students’ speaking achievement in terms of score (telling a story individually, and the students’ responses to the implementation of story-telling technique using picture series. The finding of the study indicated that the implementation of the technique was successful in improving the students’ speaking ability, since the criteria of success were achieved. The first criterion was if 70% of the students participate or are actively involved in the teaching and learning process, and the data analysis confirmed that 84% of students were actively involved. Concerning the second criterion was if 70% of the students achieve the score greater than or equal to 75, the finding showed that 81% of the students already achieved scores greater than 75. The last criterion, if 70% of students

Técnica de oscilações forçadas na análise da resposta broncodilatadora em voluntários sadios e indivíduos portadores de asma brônquica com resposta positiva Using the forced oscillation technique to evaluate bronchodilator response in healthy volunteers and in asthma patients presenting a verified positive response

Directory of Open Access Journals (Sweden)

Juliana Veiga Cavalcanti

2006-04-01

Full Text Available OBJETIVO: Analisar, através da técnica de oscilações forçadas, pacientes asmáticos com resposta broncodilatadora positiva pelo laudo espirométrico e comparar esses resultados com os obtidos em indivíduos sadios. MÉTODOS: Foram analisados 53 indivíduos não tabagistas, sendo 24 sadios sem história de doença pulmonar e 29 asmáticos com resposta broncodilatadora positiva segundo o laudo espirométrico. Todos foram submetidos à técnica de oscilações forçadas e a espirometria antes e após vinte minutos da administração de salbutamol spray (300 g. Os parâmetros derivados da técnica de oscilações forçadas foram: resistência total, reatância total, resistência extrapolada para o eixo y, coeficiente angular da reta de resistência e complacência dinâmica. Na espirometria, os parâmetros utilizados foram o volume expiratório forçado no primeiro segundo e a capacidade vital forçada. RESULTADOS: No grupo controle, a utilização do broncodilatador produziu alteração significativa na resistência extrapolada para o eixo y (p OBJECTIVE: To use the forced oscillation technique to evaluate asthma patients presenting positive bronchodilator responses (confirmed through spirometry and compare the results with those obtained in healthy individuals. METHODS: The study sample consisted of 53 non-smoking volunteers: 24 healthy subjects with no history of pulmonary disease and 29 asthmatics presenting positive bronchodilator response, as determined through analysis of spirometry findings. All of the subjects were submitted to forced oscillation technique and spirometry immediately before and 20 minutes after the administration of salbutamol spray (300 g. The parameters derived from the forced oscillation technique were total respiratory resistance, total respiratory reactance, resistance extrapolated to the y axis, the slope of resistance, and dynamic compliance. The parameters measured in the spirometry evaluation tests were forced

Translation Techniques

OpenAIRE

Marcia Pinheiro

2015-01-01

In this paper, we discuss three translation techniques: literal, cultural, and artistic. Literal translation is a well-known technique, which means that it is quite easy to find sources on the topic. Cultural and artistic translation may be new terms. Whilst cultural translation focuses on matching contexts, artistic translation focuses on matching reactions. Because literal translation matches only words, it is not hard to find situations in which we should not use this technique.  Because a...

Thermoluminescent response of LaAlO{sub 3}:Pr; Respuesta termoluminiscente de LaAlO{sub 3}:Pr

Energy Technology Data Exchange (ETDEWEB)

Morales H, A.; Zarate M, J. [Universidad Michoacana de San Nicolas de Hidalgo, Instituto de Investigacion en Metalurgia y Materiales, Ciudad Universitaria, Edif. U, 58060 Morelia, Michoacan (Mexico); Azorin N, J. [Universidad Autonoma Metropolitana, Unidad Iztapalapa, Av. San Rafael Atlixco 186, Col. Vicentina, 09340 Mexico D. F. (Mexico); Rivera M, T., E-mail: feyo_yo@hotmail.com [IPN, Centro de Investigacion en Ciencia Aplicada y Tecnologia Avanzada, Av. Legaria 694, 11500 Mexico D. F. (Mexico)

2015-10-15

In this study, the thermoluminescence response of doped lanthanum aluminate (LaAlO{sub 3}) with praseodymium ion (Pr) obtained by the Pechini method and drying by the spraying technique Spry Dryer was studied. The obtained powders were analyzed structurally by the X-ray diffraction technique; the morphological characterization was by the scanning electron microscopy technique. The obtained powders at 800 degrees C presented crystallinity and showed a Rhombohedral crystal structure, this phase was observed by X-ray diffraction patterns. Thermoluminescence response of LaAlO{sub 3}:Pr showed a brightness curve with a peak centered at 157 degrees C. The sensitivity of the doped samples was improved about 90 times in comparison with the undoped sample. Thermoluminescence response in function of the wavelength showed a maximum at 230 nm, reproducibility of thermoluminescence response was ±50%. Also the fading in thermoluminescence response was studied. (Author)

LFC based adaptive PID controller using ANN and ANFIS techniques

Directory of Open Access Journals (Sweden)

Mohamed I. Mosaad

2014-12-01

Full Text Available This paper presents an adaptive PID Load Frequency Control (LFC for power systems using Neuro-Fuzzy Inference Systems (ANFIS and Artificial Neural Networks (ANN oriented by Genetic Algorithm (GA. PID controller parameters are tuned off-line by using GA to minimize integral error square over a wide-range of load variations. The values of PID controller parameters obtained from GA are used to train both ANFIS and ANN. Therefore, the two proposed techniques could, online, tune the PID controller parameters for optimal response at any other load point within the operating range. Testing of the developed techniques shows that the adaptive PID-LFC could preserve optimal performance over the whole loading range. Results signify superiority of ANFIS over ANN in terms of performance measures.

Fluid typing and tortuosity analysis with NMR-DE techniques in volcaniclastic reservoirs, Patagonia/Argentina

Energy Technology Data Exchange (ETDEWEB)

Bustos, Ulises Daniel [Schlumberger Argentina S.A., Buenos Aires (Argentina); Breda, Eduardo Walter [Repsol YPF Comodoro Rivadavia, Chubut (Argentina)

2004-07-01

Alternative hydrocarbon-detection techniques are used to differentiate water from hydrocarbon where resistivity-based methods are difficult to apply, such as freshwater reservoirs and complex lithologies. One of these areas is represented by the complex volcaniclastic freshwater reservoirs in the Golfo San Jorge basin, Patagonia Argentina, where water and oil have often identical response on conventional logs. Some advances in hydrocarbon identification based on nuclear magnetic resonance (NMR) techniques were achieved in long T1 environments (very light oils, gas) in the Golfo San Jorge basin by previous NMR fluid typing methods. However, since medium to heavy oils are commonly present in these intervals, hydrocarbon detection by such techniques cannot be properly achieved. In addition, restricted diffusion phenomena recognized in these intervals, constitute further complications in fluid typing since its presence have similar response than native oil. To address this problem, a fluid characterization method using NMR Diffusion-Editing techniques and processing/interpretation with D-T2 maps in a suite of NMR measurements was applied. The technique allowed the detection and evaluation of restricted diffusion in these reservoirs, enabling better hydrocarbon characterization in a broad viscosity range (from light to heavy). The method also improved the petrophysical evaluation because restricted diffusion is related to tortuosity in the reservoir. Since the application of this innovative reservoir evaluation method, fluid prognosis vs well completion results was increased from around 68% to around 88% in Golfo San Jorge basin. Moreover, in some of these areas rates above 95% were recently achieved in 2004. (author)

A review of the methods for neuronal response latency estimation

DEFF Research Database (Denmark)

Levakovaa, Marie; Tamborrino, Massimiliano; Ditlevsen, Susanne

2015-01-01

Neuronal response latency is usually vaguely defined as the delay between the stimulus onset and the beginning of the response. It contains important information for the understanding of the temporal code. For this reason, the detection of the response latency has been extensively studied in the ...... by the stimulation using interspike intervals and spike times. The aim of this paper is to present a review of the main techniques proposed in both classes, highlighting their advantages and shortcomings....

Selected physiotherapeutic techniques and immune response in low back pain

Directory of Open Access Journals (Sweden)

Piotr Gawda

2017-04-01

Full Text Available Physiotherapy, as an element of medical rehabilitation, comprises such methods of function improvement as: massage, kinesiotherapy, physical therapy or manual therapy. In this area, medicine offers a wide range of treatment methods, practically at every stage of a patient’s recovery. Physiotherapy is used to enhance quality of life of people with disabilities, chronic diseases or after injuries, but also as a form of prevention of dysfunctions. The aim of the study  is to present the influence of physiotherapy of low back pain on factors of immune response based on literature review. Effectiveness of a given treatment is most easily noticeable in clinical practice. It is usually the patient who evaluates the efficiency of treatment, through experiencing less pain, easier performance of certain actions or overall better functioning in everyday life. Apart from registering the subjective experience of patients, the focus is on finding objective methods of evaluating effectiveness of physiotherapy and on attempts at scientific explanation of noticeable and perceptible influence of rehabilitation treatment. This also applies to the treatment of lumbar-sacral pain. The involvement of many inflammatory mediators such as nitric oxide, interleukins, matrix metalloproteinases, prostaglandin , tumor necrosis factor alpha and a group of cytokines. and a variety of cytokines have already been  identified in the dysfunction of this region.

Identification of shareholder ethics and responsibilities in online reverse auctions for construction projects.

Science.gov (United States)

Hatipkarasulu, Yilmaz; Gill, James H

2004-04-01

The increasing number of companies providing internet services and auction tools helped popularize the online reverse auction trend for purchasing commodities and services in the last decade. As a result, a number of owners, both public and private, accepted the online reverse auctions as the bidding technique for their construction projects. Owners, while trying to minimize their costs for construction projects, are also required to address their ethical responsibilities to the shareholders. In the case of online reverse auctions for construction projects, the ethical issues involved in the bidding technique directly reflects on the owner's ethical and social responsibilities to their shareholders. The goal of this paper is to identify the shareholder ethics and responsibilities in online reverse auctions for construction projects by analyzing the ethical issues for the parties involved in the process. The identification of the ethical issues and responsibilities requires clear definition and understanding of professional ethics and the roles of the involved parties. In this paper, first, the concept of professional ethics and social responsibility is described in a general form. To illustrate the ethical issues and responsibilities, a sample case of bidding for a construction project using online reverse auction techniques is presented in which the shareholders were actively involved in questioning the ethical issues. The issues involved in the bidding process and their reflection on the shareholder responsibilities are described and analyzed for each stage of the process. A brief discussion of the overall process is also included to address the general ethical issues involved in online reverse auctions.

Space Mapping With Adaptive Response Correction for Microwave Design Optimization

DEFF Research Database (Denmark)

Koziel, S.; Bandler, J.W.; Madsen, Kaj

2009-01-01

at which the term was calculated, as in the surrogate model optimization process. In this paper, an adaptive response correction scheme is presented to work in conjunction with space-mapping optimization algorithms. This technique is designed to alleviate the difficulties of the standard output space......Output space mapping is a technique introduced to enhance the robustness of the space-mapping optimization process in case the space-mapped coarse model cannot provide sufficient matching with the fine model. The technique often works very well; however, in some cases it fails. Especially...

Prediction of thresholds and latency on the basis of experimentally determined impulse responses

NARCIS (Netherlands)

Blommaert, F.J.J.; Roufs, J.A.J.

As was shown before (Roufs and Blommaert 1981), temporal impluse responsses and step responses can be obtained psychophysically using a driftcorrecting perturbation technique. In this paper, experimentally determined impulse responses are given for eight subjects using different experimental

Building a new predictor for multiple linear regression technique-based corrective maintenance turnaround time.

Science.gov (United States)

Cruz, Antonio M; Barr, Cameron; Puñales-Pozo, Elsa

2008-01-01

This research's main goals were to build a predictor for a turnaround time (TAT) indicator for estimating its values and use a numerical clustering technique for finding possible causes of undesirable TAT values. The following stages were used: domain understanding, data characterisation and sample reduction and insight characterisation. Building the TAT indicator multiple linear regression predictor and clustering techniques were used for improving corrective maintenance task efficiency in a clinical engineering department (CED). The indicator being studied was turnaround time (TAT). Multiple linear regression was used for building a predictive TAT value model. The variables contributing to such model were clinical engineering department response time (CE(rt), 0.415 positive coefficient), stock service response time (Stock(rt), 0.734 positive coefficient), priority level (0.21 positive coefficient) and service time (0.06 positive coefficient). The regression process showed heavy reliance on Stock(rt), CE(rt) and priority, in that order. Clustering techniques revealed the main causes of high TAT values. This examination has provided a means for analysing current technical service quality and effectiveness. In doing so, it has demonstrated a process for identifying areas and methods of improvement and a model against which to analyse these methods' effectiveness.

Using typing techniques in a specific outbreak: the ethical reflection of public health professionals.

Science.gov (United States)

Rump, B; Cornelis, C; Woonink, F; VAN Steenbergen, J; Verweij, M; Hulscher, M

2017-05-01

Typing techniques are laboratory methods used in outbreak management to investigate the degree to which microbes found within an outbreak are related. Knowledge about relational patterns between microbes benefits outbreak management, but inevitably also tells us something about the relational patterns of the people hosting them. Since the technique is often used without explicit consent of all individuals involved, this may raise ethical questions. The aim of this study was to unravel the complex ethical deliberation of professionals over the use of such techniques. We organised group discussions (n = 3) with Dutch outbreak managers (n = 23). The topic list was based on previously identified ethical issues and discussions were analysed for recurrent themes. We found that outbreak managers first and foremost reflect on the balance of individual harm with public health benefit. This key question was approached by way of discussing four more specific ethical themes: (1) justification of governmental intervention, (2) responsibility to prevent infections, (3) scientific uncertainty and (4) legal consequences. The themes found in this study, rephrased into accessible questions, represent the shared ethical understanding of professionals and can help to articulate the ethical dimensions of using molecular science in response to infectious disease outbreaks.

Sensitivity analysis technique for application to deterministic models

International Nuclear Information System (INIS)

Ishigami, T.; Cazzoli, E.; Khatib-Rahbar, M.; Unwin, S.D.

1987-01-01

The characterization of sever accident source terms for light water reactors should include consideration of uncertainties. An important element of any uncertainty analysis is an evaluation of the sensitivity of the output probability distributions reflecting source term uncertainties to assumptions regarding the input probability distributions. Historically, response surface methods (RSMs) were developed to replace physical models using, for example, regression techniques, with simplified models for example, regression techniques, with simplified models for extensive calculations. The purpose of this paper is to present a new method for sensitivity analysis that does not utilize RSM, but instead relies directly on the results obtained from the original computer code calculations. The merits of this approach are demonstrated by application of the proposed method to the suppression pool aerosol removal code (SPARC), and the results are compared with those obtained by sensitivity analysis with (a) the code itself, (b) a regression model, and (c) Iman's method

Analysis Test of Understanding of Vectors with the Three-Parameter Logistic Model of Item Response Theory and Item Response Curves Technique

Science.gov (United States)

Rakkapao, Suttida; Prasitpong, Singha; Arayathanitkul, Kwan

2016-01-01

This study investigated the multiple-choice test of understanding of vectors (TUV), by applying item response theory (IRT). The difficulty, discriminatory, and guessing parameters of the TUV items were fit with the three-parameter logistic model of IRT, using the parscale program. The TUV ability is an ability parameter, here estimated assuming…

Specific radiography technique

International Nuclear Information System (INIS)

Abdul Nassir Ibrahim; Azali Muhammad; Ab. Razak Hamzah; Abd. Aziz Mohamed; Mohamad Pauzi Ismail

2008-01-01

Beside radiography testing using x-ray machine and gamma source, there are several technique that developed specifically to complete the testing that cannot be done with the two earlier. This technique was specific based on several factor, for the example, the advantages of neutron and electron using to show the image was unique compare to x-ray and gamma. Besides that, these special radiography techniques maybe differ in how to detect the radiation get through the object. These technique can used to inspect thin or specimen that contained radioactive material. There are several technique will discussed in this chapter such as neutron radiography, electron radiography, fluoroscopy and also autoradiography.

Improved data visualization techniques for analyzing macromolecule structural changes.

Science.gov (United States)

Kim, Jae Hyun; Iyer, Vidyashankara; Joshi, Sangeeta B; Volkin, David B; Middaugh, C Russell

2012-10-01

The empirical phase diagram (EPD) is a colored representation of overall structural integrity and conformational stability of macromolecules in response to various environmental perturbations. Numerous proteins and macromolecular complexes have been analyzed by EPDs to summarize results from large data sets from multiple biophysical techniques. The current EPD method suffers from a number of deficiencies including lack of a meaningful relationship between color and actual molecular features, difficulties in identifying contributions from individual techniques, and a limited ability to be interpreted by color-blind individuals. In this work, three improved data visualization approaches are proposed as techniques complementary to the EPD. The secondary, tertiary, and quaternary structural changes of multiple proteins as a function of environmental stress were first measured using circular dichroism, intrinsic fluorescence spectroscopy, and static light scattering, respectively. Data sets were then visualized as (1) RGB colors using three-index EPDs, (2) equiangular polygons using radar charts, and (3) human facial features using Chernoff face diagrams. Data as a function of temperature and pH for bovine serum albumin, aldolase, and chymotrypsin as well as candidate protein vaccine antigens including a serine threonine kinase protein (SP1732) and surface antigen A (SP1650) from S. pneumoniae and hemagglutinin from an H1N1 influenza virus are used to illustrate the advantages and disadvantages of each type of data visualization technique. Copyright © 2012 The Protein Society.

The effects of climate downscaling technique and observational data set on modeled ecological responses

Science.gov (United States)

Afshin Pourmokhtarian; Charles T. Driscoll; John L. Campbell; Katharine Hayhoe; Anne M. K. Stoner

2016-01-01

Assessments of future climate change impacts on ecosystems typically rely on multiple climate model projections, but often utilize only one downscaling approach trained on one set of observations. Here, we explore the extent to which modeled biogeochemical responses to changing climate are affected by the selection of the climate downscaling method and training...

Using a Collaborative Critiquing Technique to Develop Chemistry Students' Technical Writing Skills

Science.gov (United States)

Carr, Jeremy M.

2013-01-01

The technique, termed "collaborative critiquing", was developed to teach fundamental technical writing skills to analytical chemistry students for the preparation of laboratory reports. This exercise, which can be completed prior to peer-review activities, is novel, highly interactive, and allows students to take responsibility for their…

Two-dimensional in situ metrology of X-ray mirrors using the speckle scanning technique

Energy Technology Data Exchange (ETDEWEB)

Wang, Hongchang, E-mail: hongchang.wang@diamond.ac.uk; Kashyap, Yogesh; Laundy, David; Sawhney, Kawal [Diamond Light Source Ltd, Harwell Science and Innovation Campus, Didcot OX11 0DE (United Kingdom)

2015-06-06

The two-dimensional slope error of an X-ray mirror has been retrieved by employing the speckle scanning technique, which will be valuable at synchrotron radiation facilities and in astronomical telescopes. In situ metrology overcomes many of the limitations of existing metrology techniques and is capable of exceeding the performance of present-day optics. A novel technique for precisely characterizing an X-ray bimorph mirror and deducing its two-dimensional (2D) slope error map is presented. This technique has also been used to perform fast optimization of a bimorph mirror using the derived 2D piezo response functions. The measured focused beam size was significantly reduced after the optimization, and the slope error map was then verified by using geometrical optics to simulate the focused beam profile. This proposed technique is expected to be valuable for in situ metrology of X-ray mirrors at synchrotron radiation facilities and in astronomical telescopes.

Spatial Angular Compounding Technique for H-Scan Ultrasound Imaging.

Science.gov (United States)

Khairalseed, Mawia; Xiong, Fangyuan; Kim, Jung-Whan; Mattrey, Robert F; Parker, Kevin J; Hoyt, Kenneth

2018-01-01

H-Scan is a new ultrasound imaging technique that relies on matching a model of pulse-echo formation to the mathematics of a class of Gaussian-weighted Hermite polynomials. This technique may be beneficial in the measurement of relative scatterer sizes and in cancer therapy, particularly for early response to drug treatment. Because current H-scan techniques use focused ultrasound data acquisitions, spatial resolution degrades away from the focal region and inherently affects relative scatterer size estimation. Although the resolution of ultrasound plane wave imaging can be inferior to that of traditional focused ultrasound approaches, the former exhibits a homogeneous spatial resolution throughout the image plane. The purpose of this study was to implement H-scan using plane wave imaging and investigate the impact of spatial angular compounding on H-scan image quality. Parallel convolution filters using two different Gaussian-weighted Hermite polynomials that describe ultrasound scattering events are applied to the radiofrequency data. The H-scan processing is done on each radiofrequency image plane before averaging to get the angular compounded image. The relative strength from each convolution is color-coded to represent relative scatterer size. Given results from a series of phantom materials, H-scan imaging with spatial angular compounding more accurately reflects the true scatterer size caused by reductions in the system point spread function and improved signal-to-noise ratio. Preliminary in vivo H-scan imaging of tumor-bearing animals suggests this modality may be useful for monitoring early response to chemotherapeutic treatment. Overall, H-scan imaging using ultrasound plane waves and spatial angular compounding is a promising approach for visualizing the relative size and distribution of acoustic scattering sources. Copyright © 2018 World Federation for Ultrasound in Medicine and Biology. Published by Elsevier Inc. All rights reserved.

Analysis test of understanding of vectors with the three-parameter logistic model of item response theory and item response curves technique

Directory of Open Access Journals (Sweden)

Suttida Rakkapao

2016-10-01

Full Text Available This study investigated the multiple-choice test of understanding of vectors (TUV, by applying item response theory (IRT. The difficulty, discriminatory, and guessing parameters of the TUV items were fit with the three-parameter logistic model of IRT, using the parscale program. The TUV ability is an ability parameter, here estimated assuming unidimensionality and local independence. Moreover, all distractors of the TUV were analyzed from item response curves (IRC that represent simplified IRT. Data were gathered on 2392 science and engineering freshmen, from three universities in Thailand. The results revealed IRT analysis to be useful in assessing the test since its item parameters are independent of the ability parameters. The IRT framework reveals item-level information, and indicates appropriate ability ranges for the test. Moreover, the IRC analysis can be used to assess the effectiveness of the test’s distractors. Both IRT and IRC approaches reveal test characteristics beyond those revealed by the classical analysis methods of tests. Test developers can apply these methods to diagnose and evaluate the features of items at various ability levels of test takers.

Analysis test of understanding of vectors with the three-parameter logistic model of item response theory and item response curves technique

Science.gov (United States)

Rakkapao, Suttida; Prasitpong, Singha; Arayathanitkul, Kwan

2016-12-01

This study investigated the multiple-choice test of understanding of vectors (TUV), by applying item response theory (IRT). The difficulty, discriminatory, and guessing parameters of the TUV items were fit with the three-parameter logistic model of IRT, using the parscale program. The TUV ability is an ability parameter, here estimated assuming unidimensionality and local independence. Moreover, all distractors of the TUV were analyzed from item response curves (IRC) that represent simplified IRT. Data were gathered on 2392 science and engineering freshmen, from three universities in Thailand. The results revealed IRT analysis to be useful in assessing the test since its item parameters are independent of the ability parameters. The IRT framework reveals item-level information, and indicates appropriate ability ranges for the test. Moreover, the IRC analysis can be used to assess the effectiveness of the test's distractors. Both IRT and IRC approaches reveal test characteristics beyond those revealed by the classical analysis methods of tests. Test developers can apply these methods to diagnose and evaluate the features of items at various ability levels of test takers.

Evaluation of flow-induced vibration prediction techniques for in-reactor components

International Nuclear Information System (INIS)

Mulcahy, T.M.; Turula, P.

1975-05-01

Selected in-reactor components of a hydraulic and structural dynamic scale model of the U. S. Energy Research and Development Administration experimental Fast Test Reactor have been studied in an effort to develop and evaluate techniques for predicting vibration behavior of elastic structures exposed to a moving fluid. Existing analysis methods are used to compute the natural frequencies and modal shapes of submerged beam and shell type components. Component response is calculated, assuming as fluid forcing mechanisms both vortex shedding and random excitations characterized by the available hydraulic data. The free and force vibration response predictions are compared with extensive model flow and shaker test data. (U.S.)

Logging technique for assaying for uranium in rocks

International Nuclear Information System (INIS)

Givens, W.W.

1973-01-01

A uranium exploration technique is described for determining the uranium content of a formation traversed by borehole. A delayed fission neutron assay log is obtained by irradiating the formation with repetitive bursts of fast neutrons and detecting delayed neutrons resulting from neutron fission of uranium at time intervals between the fast neutron bursts and after dissipation of the neutrons originating in the bursts. In addition, a response log is obtained by irradiating the formation with a source of fast neutrons whereby the neutrons from this source are moderated in the formation to lower energy levels and are subject to absorption. Secondary radiation attendant to these lower energy neutrons is recorded in order to obtain a log representative of the response of the formation to moderation and absorption of the neutrons. The two logs thus obtained are correlated in order to determine a corrected value of uranium content of the formation. (author)

Structural optimization for nonlinear dynamic response

DEFF Research Database (Denmark)

Dou, Suguang; Strachan, B. Scott; Shaw, Steven W.

2015-01-01

by a single vibrating mode, or by a pair of internally resonant modes. The approach combines techniques from nonlinear dynamics, computational mechanics and optimization, and it allows one to relate the geometric and material properties of structural elements to terms in the normal form for a given resonance......Much is known about the nonlinear resonant response of mechanical systems, but methods for the systematic design of structures that optimize aspects of these responses have received little attention. Progress in this area is particularly important in the area of micro-systems, where nonlinear...... resonant behaviour is being used for a variety of applications in sensing and signal conditioning. In this work, we describe a computational method that provides a systematic means for manipulating and optimizing features of nonlinear resonant responses of mechanical structures that are described...

Moving Is Like Making Out: Developing Female University Dancers' Ballet Technique and Expression through the Use of Metaphor

Science.gov (United States)

Spohn, Cydney; Prettyman, Sandra Spickard

2012-01-01

This qualitative study explored the use of metaphor within a somatic context as a means to bridge the divide between technique and expression in two undergraduate advanced intermediate ballet classes. Data included surveys, classroom observations, student journal responses and student work, as well as surveys and journal responses, one year after…

Assessing the Utility of the Nominal Group Technique as a Consensus-Building Tool in Extension-Led Avian Influenza Response Planning

Science.gov (United States)

Kline, Terence R.

2013-01-01

The intent of the project described was to apply the Nominal Group Technique (NGT) to achieve a consensus on Avian Influenza (AI) planning in Northeastern Ohio. Nominal Group Technique is a process first developed by Delbecq, Vande Ven, and Gustafsen (1975) to allow all participants to have an equal say in an open forum setting. A very diverse…

The use of linear programming techniques to design optimal digital filters for pulse shaping and channel equalization

Science.gov (United States)

Houts, R. C.; Burlage, D. W.

1972-01-01

A time domain technique is developed to design finite-duration impulse response digital filters using linear programming. Two related applications of this technique in data transmission systems are considered. The first is the design of pulse shaping digital filters to generate or detect signaling waveforms transmitted over bandlimited channels that are assumed to have ideal low pass or bandpass characteristics. The second is the design of digital filters to be used as preset equalizers in cascade with channels that have known impulse response characteristics. Example designs are presented which illustrate that excellent waveforms can be generated with frequency-sampling filters and the ease with which digital transversal filters can be designed for preset equalization.

Simulation tools for industrial applications of phased array inspection techniques

International Nuclear Information System (INIS)

Mahaut, St.; Roy, O.; Chatillon, S.; Calmon, P.

2001-01-01

Ultrasonic phased arrays techniques have been developed at the French Atomic Energy Commission in order to improve defects characterization and adaptability to various inspection configuration (complex geometry specimen). Such transducers allow 'standard' techniques - adjustable beam-steering and focusing -, or more 'advanced' techniques - self-focusing on defects for instance -. To estimate the performances of those techniques, models have been developed, which allows to compute the ultrasonic field radiated by an arbitrary phased array transducer through any complex specimen, and to predict the ultrasonic response of various defects inspected with a known beam. Both modeling applications are gathered in the Civa software, dedicated to NDT expertise. The use of those complementary models allows to evaluate the ability of a phased array to steer and focus the ultrasonic beam, and therefore its relevancy to detect and characterize defects. These models are specifically developed to give accurate solutions to realistic inspection applications. This paper briefly describes the CIVA models, and presents some applications dedicated to the inspection of complex specimen containing various defects with a phased array used to steer and focus the beam. Defect detection and characterization performances are discussed for the various configurations. Some experimental validation of both models are also presented. (authors)

Use of nuclear techniques in studies of soil-plant relationships

International Nuclear Information System (INIS)

Hardarson, G.

1990-01-01

The major limitation facing researchers in the developing countries when trying to benefit from the use of isotope and radiation methods for solving problems in their countries is the lack of technical information. Training courses are very efficient for transferring technology to the developing countries. The Soil Fertility, Irrigation and Crop Production Section of the Joint FAO/IAEA Division of Nuclear Techniques in Food and Agriculture and the Soil Science Unit of the IAEA Seibersdorf Laboratory have technical responsibility for organizing training courses on the use of isotopes in soil fertility and plant nutrition research. These courses have been held annually since 1978 until the present with two additional specialized courses conducted in the years 1985 and 1986 on biological nitrogen fixation. This manual was compiled from some of the lectures and practical exercises presented at these courses. Contents: Stable and radioactive isotopes. Field experimentation in isotope-aided studies. Sample preparation techniques of biological material for isotope analysis. Methods for 15 N determination. Isotope techniques in soil fertility and plant nutrition studies. Use of 15 N methodology to assess biological nitrogen fixation. Techniques in studies of photosynthesis. Use of neutron water and gamma density gauges in soil water studies. Refs, figs and tabs

Comparison of the compressive yield response of aggregated suspensions: Pressure filtration, centrifugation, and osmotic consolidation

International Nuclear Information System (INIS)

Miller, K.T.; Melant, R.M.; Zukoski, C.F.

1996-01-01

The compressive rheological responses of suspensions containing flocculated kaolin, alumina (average particle sizes of 0.2 and 0.5 microm), and hydrous zirconia (average particle sizes of 8, 57, and 139 nm) particles have been measured using three different techniques: pressure filtration, volume fraction profile during centrifugation, and sediment height during centrifugation at multiple spinning speeds. While the volume fraction profile technique appears to be experimentally most robust, equivalent responses are found using the different techniques, indicating that the compressive yield stress is a material property of a given suspension. The compressive yield stress of each suspension increases rapidly with volume fraction but cannot be generally described using simple power-law or exponential fits. The compressive yield stress also increases with the inverse square of particle size. The packing behavior of the suspensions undergoing osmotic consolidation is compared with the mechanical compressive yield response. Some suspensions exhibited the same packing behavior as in the mechanical techniques, while others consistently packed to higher densities during osmotic consolidation. Although equivalent osmotic and mechanical loads do not always result in the same volume fractions, the similar increases in volume fraction with applied driving force suggest that both the osmotic and mechanical techniques are controlled by the force needed to rearrange the particle network

The differential dieaway technique applied to the measurement of the fissile content of drums of cement encapsulated waste

International Nuclear Information System (INIS)

Swinhoe, M.T.

1986-01-01

This report describes calculations of the differential dieaway technique as applied to cement encapsulated waste. The main difference from previous applications of the technique are that only one detector position is used (diametrically opposite the neutron source) and the chamber walls are made of concrete. The results show that by rotating the drum the response to fissile material across the central plane of the drum can be made relatively uniform. The absolute size of the response is about 0.4. counts per minute per gram fissile for a neutron source of 10 8 neutrons per second. Problems of neutron and gamma background and water content are considered. (author)

Point of Technique

African Journals Online (AJOL)

.

Minimally invasive techniques are becoming popular choice for the recent times. These techniques are lowering the cost and giving the best cosmetic results. For cardiovascular surgery these techniques are much more newer and much more unknown. Open lumbar sympathectomy for certain indications is a very well ...

Responsibility structure in medical radiation applications

International Nuclear Information System (INIS)

Beekman, Z.M.

1989-01-01

The author discusses the various aspects of the responsibilities of physicians and clinical physicists with regard to radiation protection in medical applications of ionizing radiation. It becomes still clearer that the physician, who carries out the examination or the treatment, also has to bear the responsibility. this holds for the indication assessment as well as for optimization of the quality of the examination or treatment versus radiation burden of the patient, radiologic worker and thirds. Further it is clear that the physician in these will have to delegate specific tasks and responsibilities, whether or not in the elongated-arm construction. The clinical physicist is responsible in particular for the applications of the physical methods and watches the quality of the apparatus and methods used. As such he also is responsible for the technical workers, who take care of the preventive and corrective maintenance. The principal responsibility of the clinical physicist however lies in the field of standardization and calibration of medical-physical instruments. Besides this investigation into and development of new techniques, methods and apparatus come up, while also education and training of various profession groups involved need attention. (author). 6 refs.; 1 tab

Assessing Essential Qualities of Urban Space with Emotional and Visual Data Based on GIS Technique

Directory of Open Access Journals (Sweden)

Xin Li

2016-11-01

Full Text Available Finding a method to evaluate people’s emotional responses to urban spaces in a valid and objective way is fundamentally important for urban design practices and related policy making. Analysis of the essential qualities of urban space could be made both more effective and more accurate using innovative information techniques that have become available in the era of big data. This study introduces an integrated method based on geographical information systems (GIS and an emotion-tracking technique to quantify the relationship between people’s emotional responses and urban space. This method can evaluate the degree to which people’s emotional responses are influenced by multiple urban characteristics such as building shapes and textures, isovist parameters, visual entropy, and visual fractals. The results indicate that urban spaces may influence people’s emotional responses through both spatial sequence arrangements and shifting scenario sequences. Emotional data were collected with body sensors and GPS devices. Spatial clustering was detected to target effective sampling locations; then, isovists were generated to extract building textures. Logistic regression and a receiver operating characteristic analysis were used to determine the key isovist parameters and the probabilities that they influenced people’s emotion. Finally, based on the results, we make some suggestions for design professionals in the field of urban space optimization.

System Identification of Mistuned Bladed Disks from Traveling Wave Response Measurements

Science.gov (United States)

Feiner, D. M.; Griffin, J. H.; Jones, K. W.; Kenyon, J. A.; Mehmed, O.; Kurkov, A. P.

2003-01-01

A new approach to modal analysis is presented. By applying this technique to bladed disk system identification methods, one can determine the mistuning in a rotor based on its response to a traveling wave excitation. This allows system identification to be performed under rotating conditions, and thus expands the applicability of existing mistuning identification techniques from integrally bladed rotors to conventional bladed disks.

Errors in the calculation of sub-soil moisture probe by equivalent moisture content technique

International Nuclear Information System (INIS)

Lakshmipathy, A.V.; Gangadharan, P.

1982-01-01

The size of the soil sample required to obtain the saturation response, with a neutron moisture probe is quite large and this poses practical problems of handling and mixing large amounts of samples for absolute laboratory calibration. Hydrogenous materials are used as a substitute for water in the equivalent moisture content technique, for calibration of soil moisture probes. In this it is assumed that only hydrogen of the bulk sample is responsible for the slowing down of fast neutrons and the slow neutron countrate is correlated to equivalent water content by considering the hydrogen density of sample. It is observed that the higher atomic number elements present in water equivalent media also affect the response of the soil moisture probe. Hence calculations, as well as experiments, were undertaken to know the order of error introduced by this technique. The thermal and slow neutron flux distribution around the BF 3 counter of a sub-soil moisture probe is calculated using three group diffusion theory. The response of the probe corresponding to different equivalent moisture content of hydrogenous media, is calculated taking into consideration the effective length of BF 3 counter. Soil with hydrogenous media such as polyethylene, sugar and water are considered for calculation, to verify the suitability of these materials as substitute for water during calibration of soil moisture probe. Experiments were conducted, to verify the theoretically calculated values. (author)

Uranium exploration techniques

International Nuclear Information System (INIS)

Nichols, C.E.

1984-01-01

The subject is discussed under the headings: introduction (genetic description of some uranium deposits; typical concentrations of uranium in the natural environment); sedimentary host rocks (sandstones; tabular deposits; roll-front deposits; black shales); metamorphic host rocks (exploration techniques); geologic techniques (alteration features in sandstones; favourable features in metamorphic rocks); geophysical techniques (radiometric surveys; surface vehicle methods; airborne methods; input surveys); geochemical techniques (hydrogeochemistry; petrogeochemistry; stream sediment geochemistry; pedogeochemistry; emanometry; biogeochemistry); geochemical model for roll-front deposits; geologic model for vein-like deposits. (U.K.)

Wildlife response on the Alaska North Slope

International Nuclear Information System (INIS)

Costanzo, D.; McKenzie, B.

1992-01-01

Recognizing the need for a comprehensive plan to deal with potentially oiled wildlife on the Alaskan North Slope, a multifaceted wildlife protection strategy was developed and implemented during 1991. The strategy incorporated all aspects of wildlife response including protection of critical habitat, hazing, capture and stabilization, long term rehabilitation, and release. The primary wildlife response strategy emphasizes controlling of the release and spreading of spilled oil at the source to prevent or reduce contamination of potentially affected species and/or their habitat. A secondary response strategy concentrates on keeping potentially affected wildlife away from an oiled area through the use of deterrent techniques. Tertiary response involves the capture and treatment of oiled wildlife. Implementation of the strategy included the development of specialized training, the procurement of equipment, and the construction of a bird stabilization center. The result of this initiative is a comprehensive wildlife response capability on the Alaskan North Slope. 1 ref., 5 figs., 3 tabs

Application condition of optical communication technique in the nuclear power plants

International Nuclear Information System (INIS)

Sakurai, Jun

1999-01-01

As the optical communication technique can process rapidly a lot of information and exclude perfectly error action due to noise, it is adopted gradually to commercial and company communications (containing operational managements in large scale facilities) in worldwide scale in stead of conventional communication technique (containing operational controls and measurements). In application to the nuclear power plants, as forming not only change in properties but also deterioration due to radiation damage in many cases of exposure to various types of radiations such as neutron, gamma-ray, and so forth in difference with conventional using environment, its using range is limited at present. In future, development of optical fibers or elements with excellent high temperature and radiation resistances usable stably at reactor core for a long time is essential. The regular application of the optical communication technique at the nuclear power plants begins just now, which is an expected field for future large development. And, for the old nuclear power plant in present operation, substitution to the optical communication technique in accompany with replace of appliances at periodical inspections will also be conducted. Its response is already required rapidly in the Tokyo Electric Power Co., Ltd.. (G.K.)

The management of acute risks. Oil spill contingency planning and response

International Nuclear Information System (INIS)

Monk, D.C.; Cormack, D.

1992-01-01

It is clear that the risks of environmental damage can be best minimized by preventing oil spills from occurring at all. Since absolute prevention is unrealistic, however, early detection is essential and aerial surveillance techniques are of great value in this connection. If spills do occur, proper contingency planning and clean-up techniques can minimize impacts, but will rarely avoid them completely if the spilled oil reaches the coastline. It is evident that a main priority should be to prevent spilled oil reaching the coastline. The way in which oil spill response strategy is implemented is discussed in detail. It is based on four key elements: the allocation of responsibilities; contingency planning; training and exercises; regular audit of plans and response mechanisms. A case study of the oil spill strategy employed at the Sullom Voe oil terminal in Shetland is used as an illustration. (UK)

Specificity and sensitivity assessment of selected nasal provocation testing techniques

Directory of Open Access Journals (Sweden)

Edyta Krzych-Fałta

2016-12-01

Full Text Available Introduction: Nasal provocation testing involves an allergen-specific local reaction of the nasal mucosa to the administered allergen. Aim: To determine the most objective nasal occlusion assessment technique that could be used in nasal provocation testing. Material and methods : A total of 60 subjects, including 30 patients diagnosed with allergy to common environmental allergens and 30 healthy subjects were enrolled into the study. The method used in the study was a nasal provocation test with an allergen, with a standard dose of a control solution and an allergen (5,000 SBU/ml administered using a calibrated atomizer into both nostrils at room temperature. Early-phase nasal mucosa response in the early phase of the allergic reaction was assessed via acoustic rhinometry, optical rhinometry, nitric oxide in nasal air, and tryptase levels in the nasal lavage fluid. Results : In estimating the homogeneity of the average values, the Levene’s test was used and receiver operating characteristic curves were plotted for all the methods used for assessing the nasal provocation test with an allergen. Statistically significant results were defined for p < 0.05. Of all the objective assessment techniques, the most sensitive and characteristic ones were the optical rhinometry techniques (specificity = 1, sensitivity = 1, AUC = 1, PPV = 1, NPV = 1. Conclusions : The techniques used showed significant differences between the group of patients with allergic rhinitis and the control group. Of all the objective assessment techniques, those most sensitive and characteristic were the optical rhinometry.

Investigating deformation processes in AM60 magnesium alloy using the acoustic emission technique

International Nuclear Information System (INIS)

Mathis, K.; Chmelik, F.; Janecek, M.; Hadzima, B.; Trojanova, Z.; Lukac, P.

2006-01-01

Microstructure changes in an AM60 magnesium alloy were monitored using the acoustic emission (AE) technique during tensile tests in the temperature range from 20 to 300 deg. C. The correlation of the AE signal and the deformation processes is discussed. It is shown, using transmission electron and light microscopy, that the character of the AE response is associated with various modes of mechanical twinning at lower temperatures, whereas at higher temperatures also the influence of non-basal dislocations on the AE response must be taken into account

Persian fencing techniques

Directory of Open Access Journals (Sweden)

Manouchehr Moshtagh Khorasani

2012-07-01

Full Text Available There are numerous manuscripts, poems and stories that describe, specifically and in detail, the different techniques used in Persian swordsmanship. The present article explains the origins and the techniques of Persian swordsmanship. The article also describes the traditional code of conduct for Persian warriors. Additionally, it describes an array of techniques that were deployed in actual combat in Iran’s history. Some of these techniques are represented via the miniatures that are reproduced herein. This is the first article on Persian swordsmanship published in any periodical.

Radiation scattering techniques

International Nuclear Information System (INIS)

Edmonds, E.A.

1986-01-01

Radiation backscattering techniques are useful when access to an item to be inspected is restricted to one side. These techniques are very sensitive to geometrical effects. Scattering processes and their application to the determination of voids, thickness measuring, well-logging and the use of x-ray fluorescence techniques are discussed. (U.K.)

A clinicopathological study of various oral cancer diagnostic techniques

Directory of Open Access Journals (Sweden)

G Ulaganathan

2017-01-01

Full Text Available Oral cancer is one of the most commonly occurring malignant tumors in the head and neck regions with high incident rate and mortality rate in the developed countries than in the developing countries. Generally, the survival rate of cancer patients may increase when diagnosed at early stage, followed by prompt treatment and therapy. Recently, cancer diagnosis and therapy design for a specific cancer patient have been performed with the advanced computer-aided techniques. The responses of the cancer therapy could be continuously monitored to ensure the effectiveness of the treatment process that hardly requires diagnostic result as quick as possible to improve the quality and patient care. This paper gives an overview of oral cancer occurrence, different types, and various diagnostic techniques. In addition, a brief introduction is given to various stages of immunoanalysis including tissue image preparation, whole slide imaging, and microscopic image analysis.

Dynamic solution of vessel depressuring; Simulacao dinamica de despressurizacao em vasos

Energy Technology Data Exchange (ETDEWEB)

Rodriguez, Marco Tulio; Silva Netto, Rafael [Chemtech Servicos de Engenharia e Software Ltda., Rio de Janeiro, RJ (Brazil); Aires, Joyce Stone S. [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil). Centro de Pesquisas (CENPES)

2004-07-01

Vessel depressuring is an important phenomenon on chemical and petrochemical processes, specially those related to oil and gas exploration, production and processing. The correct modeling of this phenomenon and prediction of the temperatures, mass and thermal rates involved is essential to the adequate design of the equipment, materials specification and safety standards assurance. To fulfill these requirements, we developed a method to simulate the phenomenon of depressuring. In this approach, the dynamic process is discretized along time, being calculated at each interval the conditions inside the vessel, material flow and heat exchanges with the environment, through mass and energy balances and thermodynamic equilibrium calculation. The method can include different models to calculate heat exchanges and flow through the relief valve, and new methods can be incorporated if necessary. The efficiency of the method was verified by comparing its results with the ones obtained by market-leaders process simulators, when it was proved the robustness of the method and precision of the results. To increase its flexibility of use, the method was incorporated to the PETROBRAS Process Simulator - PETROX (PETROBRAS, 2004), in a development made by Chemtech under a contract with PETROBRAS and already used in large scale by PETROBRAS to simulate its process units. (author)

Preference for different relaxation techniques by COPD patients: comparison between six techniques

Directory of Open Access Journals (Sweden)

Hyl

2016-09-01

Full Text Available Michael E Hyland,1 David MG Halpin,2 Sue Blake,3 Clare Seamark,3 Margaret Pinnuck,3 David Ward,3 Ben Whalley,1 Colin J Greaves,4 Adam L Hawkins,5 Dave Seamark3 1School of Psychology, University of Plymouth, Plymouth, 2Department of Respiratory Medicine, Royal Devon and Exeter Hospital, Exeter, 3Honiton Group Practice, Honiton, 4University of Exeter Medical School, Exeter, 5GSK House, Brentford, UK Background: A review of the effectiveness of relaxation techniques for chronic obstructive pulmonary disease patients has shown inconsistent results, but studies have varied in terms of technique and outcome measures. Aim: To determine patient preference for different relaxation techniques. Methods: Chronic obstructive pulmonary disease patients were presented with six techniques via a DVD and asked to rate the techniques in terms of effectiveness, rank in order of likely use, and comment. Results: Patients differed in the technique preferred and reason for that preference, but the most commonly preferred technique both for effectiveness and ease of use was “thinking of a nice place” followed by progressive relaxation and counting. Familiarity and ease of activity were commonly given reasons for preference. Conclusion: Rather than providing patients with a single technique that they might find difficult to implement, these results suggest that it would be better to give a choice. “Thinking of a nice place” is a popular but under-investigated technique. Keywords: COPD exacerbation, anxiety, relaxation techniques

COMPARISON OF THE MECHANICAL RESPONSE OF POROUS TI-6AL-4V ALLOYS PRODUCED BY DIFFERENT COMPACTION TECHNIQUES

Directory of Open Access Journals (Sweden)

G.İpek Selimoğlu

2017-03-01

Full Text Available Porous Ti-6Al-4V alloys are attractive candidates as implant materials due to their good biocompatibility combined with the porous structure leading to increased osseointegration and decreased stiffness. Accordingly, different processing techniques were employed for the production of Ti-6Al-4V foams in the literature. Among these techniques, sintering with space holder is used to produce porous Ti-6Al-4V alloys in this study. Magnesium was employed as the space holder material because of its relatively low boiling point as well as high oxygen affinity. Two different compaction techniques, die compaction with hydraulic pressing and cold isostatic pressing (CIP, were employed for obtaining green compacts. Both spherical and nonspherical Ti-6Al-4V powders were used to investigate the effect of powder shape on compaction. Processed foams were characterized in terms of both microstructural and mechanical aspects in order to investigate the effect of pressing conditions in combination with powder characteristics. It was observed that NS-CIP foam, which was produced by compacting nonspherical powders by cold isostatic press, has the highest strength. However, the S-DP foam, which was produced by die-pressing of spherical powders, has the highest toughness.

Structural health monitoring in composite materials using frequency response methods

Science.gov (United States)

Kessler, Seth S.; Spearing, S. Mark; Atalla, Mauro J.; Cesnik, Carlos E. S.; Soutis, Constantinos

2001-08-01

Cost effective and reliable damage detection is critical for the utilization of composite materials in structural applications. Non-destructive evaluation techniques (e.g. ultrasound, radiography, infra-red imaging) are available for use during standard repair and maintenance cycles, however by comparison to the techniques used for metals these are relatively expensive and time consuming. This paper presents part of an experimental and analytical survey of candidate methods for the detection of damage in composite materials. The experimental results are presented for the application of modal analysis techniques applied to rectangular laminated graphite/epoxy specimens containing representative damage modes, including delamination, transverse ply cracks and through-holes. Changes in natural frequencies and modes were then found using a scanning laser vibrometer, and 2-D finite element models were created for comparison with the experimental results. The models accurately predicted the response of the specimems at low frequencies, but the local excitation and coalescence of higher frequency modes make mode-dependent damage detection difficult and most likely impractical for structural applications. The frequency response method was found to be reliable for detecting even small amounts of damage in a simple composite structure, however the potentially important information about damage type, size, location and orientation were lost using this method since several combinations of these variables can yield identical response signatures.

Polymer composites for optical imaging and X-rays in hydraulic simulation tanks; Compositos polimericos para imageamento optico e por raios-x em tanques de simulacao hidraulica

Energy Technology Data Exchange (ETDEWEB)

Reis, Maria H.S.; Goncalves, Raiane V.; Basso, Nara R.S.; Moura, Cassio S., E-mail: maria.helena@acad.pucrs.br, E-mail: raiane.goncalves@acad.pucrs.br, E-mail: nrbass@pucrs.br, E-mail: cassio.moura@pucrs.br [Pontificia Universidade Catolica do Rio Grande do Sul (PUC-RS), Porto Alegre, RS (Brazil)

2015-07-01

This research is related to new approaches for non-invasive imaging techniques that allows registering the internal architecture of sedimentary deposits generated in hydraulic simulation tanks to better understand the behavior of density currents. Polymeric composite with properties and characteristics similar to coal 205 was prepared with inorganic filler for non-destructive tests. It was used an orthophthalic polyester resin with different dye loads and barium sulfate as inorganic filler. Tests on x-ray Microtomography showed that the barium sulphate provides the necessary opacity for detection with such technique. Scanning electron microscopy allowed evaluating and classifying the shape of the matrix and measuring the nanometric dimensions of the filler. Specific mass and drop rate were also evaluated and it was found that the incorporation of dye and filler did not affected significantly the desired characteristics. For this reasons, the composite prepared show potential use in simulations and non-invasive imaging. (author)

Technique charts for EC film: direct optical measurements to account for the effects of X-ray scatter

International Nuclear Information System (INIS)

Munro, Peter; Jordan, Kevin; Lewis, Craig; Heerema, Tim

2001-01-01

Purpose: To develop a method of measuring technique charts for enhanced contrast (EC) film, to demonstrate how X-ray scatter changes the response of EC film, and to generate technique charts for general use. Methods and Materials: We have developed a 'digital cassette' - consisting of a metal plate/phosphor screen, a light guide, a photodiode sensor, and an electrometer - that can be used to measure the light generated in the phosphor screen of the film cassette. In turn, these measurements can be used to generate technique charts for EC film. The digital cassette has been used to measure technique charts for 4-MV and 6-MV X-ray beams for a variety of different phantom thicknesses, field sizes, and phantom-to-cassette air gaps. Results and Discussion: We have observed that the signals generated in an ionization chamber located 9.4 cm behind a 30-cm-thick water-equivalent phantom increase by a factor of 1.9 when the field size is increased from 4x4 cm 2 to 40x40 cm 2 when irradiated by a 6-MV X-ray beam. However, the change in EC film response is a factor of 3.5 under the same conditions. Irradiations to optimally expose the EC film predicted by the digital cassette differ by up to 82% compared to those predicted by ion chamber measurements. Nevertheless, the technique charts measured using the digital cassette predict the response of the EC film to ±0.2 optical density. The overresponse of the EC film is most likely due to low-energy scattered photons, which interact with the high atomic number (Z=64) phosphor screen of the enhanced contrast localization cassette. Therefore, simple solutions, such as placing a high atomic number material above the enhanced contrast localization cassette, can reduce this contribution by scattered photons to the signal generated in the cassettes. Conclusions: We have developed a digital cassette that can make more accurate measurements of the technique charts for EC films. Our measurements show that under some conditions, X

Uncertainty in soil-structure interaction analysis arising from differences in analytical techniques

International Nuclear Information System (INIS)

Maslenikov, O.R.; Chen, J.C.; Johnson, J.J.

1982-07-01

This study addresses uncertainties arising from variations in different modeling approaches to soil-structure interaction of massive structures at a nuclear power plant. To perform a comprehensive systems analysis, it is necessary to quantify, for each phase of the traditional analysis procedure, both the realistic seismic response and the uncertainties associated with them. In this study two linear soil-structure interaction techniques were used to analyze the Zion, Illinois nuclear power plant: a direct method using the FLUSH computer program and a substructure approach using the CLASSI family of computer programs. In-structure response from two earthquakes, one real and one synthetic, was compared. Structure configurations from relatively simple to complicated multi-structure cases were analyzed. The resulting variations help quantify uncertainty in structure response due to analysis procedures

Aesthetic responses to music

DEFF Research Database (Denmark)

Istok, Eva; Brattico, Elvira; Jacobsen, Thomas

2009-01-01

We explored the content and structure of the cognitive, knowledge-based concept underlying aesthetic responses to music. To this aim, we asked 290 Finnish students to verbally associate the aesthetic value of music and to write down a list of appropriate adjectives within a given time limit....... No music was presented during the task. In addition, information about participants' musical background was collected. A variety of analysis techniques was used to determine the key results of our study. The adjective "beautiful" proved to be the core item of the concept under question. Interestingly......, the adjective "touching" was often listed together with "beautiful". In addition, we found music-specific vocabulary as well as adjectives related to emotions and mood states indicating that affective processes are an essential part of aesthetic responses to music. Differences between music experts and laymen...

Radiogenomics and radiotherapy response modeling

Science.gov (United States)

El Naqa, Issam; Kerns, Sarah L.; Coates, James; Luo, Yi; Speers, Corey; West, Catharine M. L.; Rosenstein, Barry S.; Ten Haken, Randall K.

2017-08-01

Advances in patient-specific information and biotechnology have contributed to a new era of computational medicine. Radiogenomics has emerged as a new field that investigates the role of genetics in treatment response to radiation therapy. Radiation oncology is currently attempting to embrace these recent advances and add to its rich history by maintaining its prominent role as a quantitative leader in oncologic response modeling. Here, we provide an overview of radiogenomics starting with genotyping, data aggregation, and application of different modeling approaches based on modifying traditional radiobiological methods or application of advanced machine learning techniques. We highlight the current status and potential for this new field to reshape the landscape of outcome modeling in radiotherapy and drive future advances in computational oncology.

New technique for tissue-equivalent gamma ray dosimetry

International Nuclear Information System (INIS)

Squillante, M.R.; Stern, I.; Nagarkar, V.; Entine, G.

1992-01-01

The use of semiconductor sensors in dosimeters is attractive for a variety of reasons including potential low cost and high sensitivity. However, the accurate measurement of the radiation dose to tissue using solid state detectors is made difficult by the relatively high atomic number of semiconductor materials. This leads to an over response to gamma ray energies below 100 keV and an under response above that. If the energy spectrum is known, corrections can be applied to yield accurate dose. In real life situations, however, the energy spectrum is not always known and may be difficult to determine at high flux rates. Also, in some cases, the energy spectrum may change with time. This paper reports that, by operating a custom-designed CdTe sensor in the pulse mode and measuring the average energy deposited, a nearly-linear relationship between the tissue dose rate and the sensor signal was obtained. Based on this technique, a prototype detector and dosimeter system were developed

Heart and Lungs Protection Technique for Cardiac Surgery with Cardiopulmonary Bypass

Directory of Open Access Journals (Sweden)

Vladimir Pichugin

2014-12-01

Full Text Available Introduction: Cardioplegic cardiac arrest with subsequent ischemic-reperfusion injuries can lead to the development of inflammation of the myocardium, leucocyte activation, and release of cardiac enzymes. Flow reduction to the bronchial arteries, causing low-flow lung ischemia, leads to the development of a pulmonary regional inflammatory response. Hypoventilation during cardiopulmonary bypass (CPB is responsible for development of microatelectasis, hydrostatic pulmonary edema, poor compliance, and a higher incidence of infection. Based on these facts, prevention methods of these complications were developed. The aim of this study was to evaluate constant coronary perfusion (CCP and the “beating heart” in combination with pulmonary artery perfusion (PAP and “ventilated lungs” technique for heart and lung protection in cardiac surgery with CPB.Methods. After ethical approval and written informed consent, 80 patients undergoing cardiac surgery with normothermic CPB were randomized in three groups. In the first group (22 patients, the crystalloid cardioplegia without lung ventilation/perfusion techniques were used. In the second group (30 patients, the CCP and “beating heart” without lung ventilation/perfusion techniques were used. In the third group (28 patients, the CCP with PAP and lung ventilation techniques were used. Clinical, functional parameters, myocardial damage markers (CK MB level, oxygenation index, and lung compliance were investigated.Results. There were higher rates of spontaneous cardiac recovery and lower doses of inotrops in the second and third groups. Myocardial contractility function was better preserved in the second and third groups. The post-operative levels of CK-MB were lower than in control group.  Three hours after surgery CK-MB levels in the second and third  groups were lower by 38.1% and 33.3%, respectively. Eight hours after surgery, CK-MB levels were lower in the second and third groups by 45.9% and

Ways to improve of corporate social responsibility in Ukrainian forestry

Directory of Open Access Journals (Sweden)

Martyinenko Irina

2016-02-01

Full Text Available The article analyzes the marketing techniques of corporate social responsibility in the current conditions of the Ukrainian wood industry with an emphasis on the need to conduct non-financial reporting

Nonlinear analysis techniques for use in the assessment of high-level waste tank structures

International Nuclear Information System (INIS)

Moore, C.J.; Julyk, L.J.; Fox, G.L.; Dyrness, A.D.

1991-01-01

Reinforced concrete in combination with a steel liner has had a wide application to structures containing hazardous material. The buried double-shell waste storage tanks at the US Department of Energy's Hanford Site use this construction method. The generation and potential ignition of combustible gases within the primary tank is postulated to develop beyond-design-basis internal pressure and possible impact loading. The scope of this paper includes the illustration of analysis techniques for the assessment of these beyond-design-basis loadings. The analysis techniques include the coupling of the gas dynamics with the structural response, the treatment of reinforced concrete in regimes of inelastic behavior, and the treatment of geometric nonlinearities. The techniques and software tools presented provide a powerful nonlinear analysis capability for storage tanks

Electrical-Based Diagnostic Techniques for Assessing Insulation Condition in Aged Transformers

Directory of Open Access Journals (Sweden)

Issouf Fofana

2016-08-01

Full Text Available The condition of the internal cellulosic paper and oil insulation are of concern for the performance of power transformers. Over the years, a number of methods have been developed to diagnose and monitor the degradation/aging of the transformer internal insulation system. Some of this degradation/aging can be assessed from electrical responses. Currently there are a variety of electrical-based diagnostic techniques available for insulation condition monitoring of power transformers. In most cases, the electrical signals being monitored are due to mechanical or electric changes caused by physical changes in resistivity, inductance or capacitance, moisture, contamination or aging by-products in the insulation. This paper presents a description of commonly used and modern electrical-based diagnostic techniques along with their interpretation schemes.

The History of Electromagnetic Induction Techniques in Soil Survey

Science.gov (United States)

Brevik, Eric C.; Doolittle, Jim

2014-05-01

Electromagnetic induction (EMI) has been used to characterize the spatial variability of soil properties since the late 1970s. Initially used to assess soil salinity, the use of EMI in soil studies has expanded to include: mapping soil types; characterizing soil water content and flow patterns; assessing variations in soil texture, compaction, organic matter content, and pH; and determining the depth to subsurface horizons, stratigraphic layers or bedrock, among other uses. In all cases the soil property being investigated must influence soil apparent electrical conductivity (ECa) either directly or indirectly for EMI techniques to be effective. An increasing number and diversity of EMI sensors have been developed in response to users' needs and the availability of allied technologies, which have greatly improved the functionality of these tools. EMI investigations provide several benefits for soil studies. The large amount of georeferenced data that can be rapidly and inexpensively collected with EMI provides more complete characterization of the spatial variations in soil properties than traditional sampling techniques. In addition, compared to traditional soil survey methods, EMI can more effectively characterize diffuse soil boundaries and identify included areas of dissimilar soils within mapped soil units, giving soil scientists greater confidence when collecting spatial soil information. EMI techniques do have limitations; results are site-specific and can vary depending on the complex interactions among multiple and variable soil properties. Despite this, EMI techniques are increasingly being used to investigate the spatial variability of soil properties at field and landscape scales.

Comprehensive evaluation of the acoustic impulse-response of apples as a measure of fruit quality

OpenAIRE

Landahl, Sandra

2007-01-01

The acoustic impulse-response technique is a means to evaluate apple quality. In this work the effect of physiological changes in the fruit on the physical measurements of fruit quality are examined. In the acoustic impulse-response technique the fruit is mechanically excited by an impact force and starts to vibrate at its own natural frequency. The resulting sound waves are then recorded and analysed. It is a fast method and yields a produce-averaged value: the stiffness factor. Experimen...

Training techniques for industry

International Nuclear Information System (INIS)

Jones, D.W.

1978-01-01

The advantages and disadvantages of commonly used training techniques in relation to cost-effective, prevention-oriented Quality Assurance are examined. Important questions are whether training techniques teach cost effectiveness and whether the techniques are, themselves, cost effective. To answer these questions, criteria for evaluating teaching techniques for cost effectiveness were developd, and then commonly used techniques are evaluated in terms of specific training program objectives. Motivation of personnel is also considered important to the success of a training program, and methods are outlined by which recognition of the academic quality of industrial training can be used as a motivational technique

Movements Indicate Threat Response Phases in Children at Risk for Anxiety.

Science.gov (United States)

McGinnis, Ellen W; McGinnis, Ryan S; Muzik, Maria; Hruschak, Jessica; Lopez-Duran, Nestor L; Perkins, Noel C; Fitzgerald, Kate; Rosenblum, Katherine L

2017-09-01

Temporal phases of threat response, including potential threat (anxiety), acute threat (startle, fear), and post-threat response modulation, have been identified as the underlying markers of anxiety disorders. Objective measures of response during these phases may help identify children at risk for anxiety; however, the complexity of current assessment techniques prevent their adoption in many research and clinical contexts. We propose an alternative technology, an inertial measurement unit (IMU), that enables noninvasive measurement of the movements associated with threat response, and test its ability to detect threat response phases in young children at a heightened risk for developing anxiety. We quantified the motion of 18 children (3-7 years old) during an anxiety-/fear-provoking behavioral task using an IMU. Specifically, measurements from a single IMU secured to the child's waist were used to extract root-mean-square acceleration and angular velocity in the horizontal and vertical directions, and tilt and yaw range of motion during each threat response phase. IMU measurements detected expected differences in child motion by threat phase. Additionally, potential threat motion was positively correlated to familial anxiety risk, startle range of motion was positively correlated with child internalizing symptoms, and response modulation motion was negatively correlated to familial anxiety risk. Results suggest differential theory-driven threat response phases and support previous literature connecting maternal child risk to anxiety with behavioral measures using more feasible objective methods. This is the first study demonstrating the utility of an IMU for characterizing the motion of young children to mark the phases of threat response modulation. The technique provides a novel and objective measure of threat response for mental health researchers.

Seismic response of free standing fuel rack construction to 3-D floor motion

International Nuclear Information System (INIS)

Soler, A.I.; Singh, K.

1983-01-01

Seismic analysis of free standing submerged racks is complicated by the presence of water and structural non-linearities such as fuel assembly cell impact and floor interface friction. A direct time integration technique has been proposed to analyze this class of structures. Application of the time integration technique on a fourteen degree of freedom lumped mass model of the rack reveals some heretofore unpublished quirks in the structure's behavior. The method of analysis is utilized to compare the seismic response of some representative rack designs. Results show wide differences in the structural response, depending on the fabrication details of racks

Improved X-ray diagnosis of stomach by progress in the development of contrast media and examination techniques

International Nuclear Information System (INIS)

Lotz, W.

1982-01-01

Three factors have been responsible for the advances during the past few years in X-ray examination of the stomach: Improvement of the contrast media used; introduction of the rare-earth foils; and examination techniques imaging all sections of the stomach and of the duodenal bulb under hypotension in double-contrast technique, in complete filling, and imaging the accessible sections by means of proper compression. An interesting technique employs a combination of two different barium sulphate suspension used at the same time, e.g. Bubbly Barium or some other barium sulphate preparation with a small amount of High-Density Barium yielding excellent image of the gastric mucosa (technique with two contrast media). (orig.) [de

Important hydrodynamic and spectroscopic techniques in the field of chromatin structure

Energy Technology Data Exchange (ETDEWEB)

Olins, D. E.

1978-01-01

Combining hydrodynamic and spectroscopic techniques in the study of conformational states of ..nu../sub 1/ induced by a variety of perturbants has led us to a general coneption: the two structural domains of ..nu../sub 1/ (i.e., the DNA-rich outer shell and the ..cap alpha..-helix-rich apolar histone core) exhibit differential responsiveness. In general, the ..cap alpha..-helical regions are more resistant, than DNA conformation or ..nu../sub 1/ size and shape, to the perturbing effects of urea, decreased ionic strength and pH, trypsin treatment, or a variety of water-miscible organic solvents. There are a number of reasonable conceptual models to explain this differential responsiveness of the structural domains of ..nu../sub 1/.

Dynamic tensile response of alumina-Al composites

International Nuclear Information System (INIS)

Atisivan, R.; Bandyopadhyay, A.; Gupta, Y. M.

2002-01-01

Plate impact experiments were carried out to examine the high strain-rate tensile response of alumina-aluminum (Al) composites with tailored microstructures. A novel processing technique was used to fabricate interpenetrating phase alumina-aluminum composites with controlled microstructures. Fused deposition modeling (FDM), a commercially available rapid prototyping technique, was used to produce the controlled porosity mullite ceramic preforms. Alumina-Al composites were then processed via reactive metal infiltration of porous mullite ceramics. With this approach, both the micro as well as the macro structures can be designed via computer aided design (CAD) to tailor the properties of the composites. Two sets of dynamic tensile experiments were performed. In the first, the metal content was varied between 23 and 39 wt. percent. In the second, the microstructure was varied while holding the metal content nearly constant. Samples with higher metal content, as expected, displayed better spall resistance. For a given metal content, samples with finer metal diameter showed better spall resistance. Relationship of the microstructural parameters on the dynamic tensile response of the structured composites is discussed here

Keyboarding Instruction at NABTE Institutions: Are We Teaching Techniques to Reduce CTD Incidence?

Science.gov (United States)

Blaszczynski, Carol; Joyce, Marguerite Shane

1996-01-01

Responses from 157 of 193 business teachers who teach keyboarding indicated that 78.7% were aware of cumulative trauma disorder and 22% had experienced it. Only 13% of classrooms were equipped with wrist rests. About 53% teach techniques to reduce incidence, but 20% did not know whether they taught preventive measures. (SK)

Investigating the probability of detection of typical cavity shapes through modelling and comparison of geophysical techniques

Science.gov (United States)

James, P.

2011-12-01

With a growing need for housing in the U.K., the government has proposed increased development of brownfield sites. However, old mine workings and natural cavities represent a potential hazard before, during and after construction on such sites, and add further complication to subsurface parameters. Cavities are hence a limitation to certain redevelopment and their detection is an ever important consideration. The current standard technique for cavity detection is a borehole grid, which is intrusive, non-continuous, slow and expensive. A new robust investigation standard in the detection of cavities is sought and geophysical techniques offer an attractive alternative. Geophysical techniques have previously been utilised successfully in the detection of cavities in various geologies, but still has an uncertain reputation in the engineering industry. Engineers are unsure of the techniques and are inclined to rely on well known techniques than utilise new technologies. Bad experiences with geophysics are commonly due to the indiscriminate choice of particular techniques. It is imperative that a geophysical survey is designed with the specific site and target in mind at all times, and the ability and judgement to rule out some, or all, techniques. To this author's knowledge no comparative software exists to aid technique choice. Also, previous modelling software limit the shapes of bodies and hence typical cavity shapes are not represented. Here, we introduce 3D modelling software (Matlab) which computes and compares the response to various cavity targets from a range of techniques (gravity, gravity gradient, magnetic, magnetic gradient and GPR). Typical near surface cavity shapes are modelled including shafts, bellpits, various lining and capping materials, and migrating voids. The probability of cavity detection is assessed in typical subsurface and noise conditions across a range of survey parameters. Techniques can be compared and the limits of detection distance

A Roadmap of Risk Diagnostic Methods: Developing an Integrated View of Risk Identification and Analysis Techniques

National Research Council Canada - National Science Library

Williams, Ray; Ambrose, Kate; Bentrem, Laura

2004-01-01

...), which is envisioned to be a comprehensive reference tool for risk identification and analysis (RI AND A) techniques. Program Managers (PMs) responsible for developing or acquiring software-intensive systems typically identify risks in different ways...

Local field enhanced second-harmonic response of organic nanofibers

DEFF Research Database (Denmark)

Leißner, Till; Kostiučenko, Oksana; Fiutowski, Jacek

Organic CNHP4 nanofibers showing a strong second-harmonic (SH) response have been successfully implemented as active components in a metal-organic hybrid system. Using nondestructive roll-on transfer technique nanofibers were transferred from the growing mica substrates onto electron...

Consulting the oracle: ten lessons from using the Delphi technique in nursing research.

Science.gov (United States)

Keeney, Sinead; Hasson, Felicity; McKenna, Hugh

2006-01-01

The aim of this paper was to provide insight into the Delphi technique by outlining our personal experiences during its use over a 10-year period in a variety of applications. As a means of achieving consensus on an issue, the Delphi research method has become widely used in healthcare research generally and nursing research in particular. The literature on this technique is expanding, mainly addressing what it is and how it should be used. However, there is still much confusion and uncertainty surrounding it, particularly about issues such as modifications, consensus, anonymity, definition of experts, how 'experts' are selected and how non-respondents are pursued. This issues that arise when planning and carrying out a Delphi study include the definition of consensus; the issue of anonymity vs. quasi-anonymity for participants; how to estimate the time needed to collect the data, analyse each 'round', feed back results to participants, and gain their responses to this feedback; how to define and select the 'experts' who will be asked to participate; how to enhance response rates; and how many 'rounds' to conduct. Many challenges and questions are raised when using the Delphi technique, but there is no doubt that it is an important method for achieving consensus on issues where none previously existed. Researchers need to adapt the method to suit their particular study.

Nonlinear response matrix methods for radiative transfer

International Nuclear Information System (INIS)

Miller, W.F. Jr.; Lewis, E.E.

1987-01-01

A nonlinear response matrix formalism is presented for the solution of time-dependent radiative transfer problems. The essential feature of the method is that within each computational cell the temperature is calculated in response to the incoming photons from all frequency groups. Thus the updating of the temperature distribution is placed within the iterative solution of the spaceangle transport problem, instead of being placed outside of it. The method is formulated for both grey and multifrequency problems and applied in slab geometry. The method is compared to the more conventional source iteration technique. 7 refs., 1 fig., 4 tabs

Calculations of transient fields in the Felix experiments at Argonne using null field integrated techniques

International Nuclear Information System (INIS)

Han, H.C.; Davey, K.R.; Turner, L.

1985-08-01

The transient eddy current problem is characteristically computationally intensive. The motivation for this research was to realize an efficient, accurate, solution technique involving small matrices via an eigenvalue approach. Such a technique is indeed realized and tested using the null field integral technique. Using smart (i.e., efficient, global) basis functions to represent unknowns in terms of a minimum number of unknowns, homogeneous eigenvectors and eigenvalues are first determined. The general excitatory response is then represented in terms of these eigenvalues/eigenvectors. Excellent results are obtained for the Argonne Felix cylinder experiments using a 4 x 4 matrix. Extension to the 3-D problem (short cylinder) is set up in terms of an 8 x 8 matrix

Detection, diagnosis, and treatment of accident conditions using response trees

International Nuclear Information System (INIS)

Nelson, W.R.

1980-01-01

Response Trees were developed at the LOFT facility in 1978 and included in the Plant Operating Manual (POM) to assist reactor operators in selecting emergency procedures. In an emergency situation the operator would manually gather data and evaluate the trees to select the appropriate procedures. As a portion of the LOFT Augmented Operator Capability (AOC) Program, the response tree methodology has been extended so that a computer can be used to evaluate the trees and recommend an appropriate response for an accident. Techniques for diagnosing failures within a cooling mode have also been investigated. This paper summarizes these additions to the response tree methodology

The Limits of Corporate Social Responsibility: Techniques of Neutralization, Stakeholder Management and Political CSR

OpenAIRE

Lee, Kelley; Fooks, Gary; Gilmore, Anna; Collin, Jeff; Holden, Chris

2012-01-01

: Since scholarly interest in corporate social responsibility (CSR) has primarily focused on the synergies between social and economic performance, our understanding of how (and the conditions under which) companies use CSR to produce policy outcomes that work against public welfare has remained comparatively under-developed. In particular, little is known about how corporate decision-makers privately reconcile the conflicts between public and private interests, even though this is likely to ...

The relationship between virtuous CEOs and corporate social responsibility

OpenAIRE

Frende Vega, María de los Ángeles; Carmelo Ordaz, Carmen; Ruiz Navarro, José

2014-01-01

This study tests the effects of virtuous CEOs on corporate social responsibility views (narrow vs broad). Using the data envelopment analysis (DEA) technique, we find that virtuous CEOs correlated positively with a broad view of corporate social responsibility (CSR). We also examine the moderating role the board of directors plays in the relationship between virtuous CEOs and CSR but finds no positive association. Our results indicate that CEOs matter and that their virtuous values may be a m...

Requirements for critical thinking support in crisis response

NARCIS (Netherlands)

Ven, J.G.M. van de; Schraagen, J.M.C.

2004-01-01

The main purpose of this paper is to describe the research done during the past four years in the Combined Systems Project. The aim of this project was to use innovative techniques to improve the decision-making process in crisis response organizations. The focus was on building situation awareness

Quantitative radiation dose-response relationships for normal tissues in man. II. Response of the salivary glands during radiotherapy

International Nuclear Information System (INIS)

Mossman, K.L.

1983-01-01

A quantitative dose-response curve for salivary gland function in patients during radiotherapy is presented. Salivary-function data used in this study were obtained from four previously published reports. All patients were treated with 60 Co teletherapy to the head and neck using conventional treatment techniques. Salivary dysfunction was determined at specific dose levels by comparing salivary flow rates before therapy with flow rates at specific dose intervals during radiotherapy up to a total dose of 6000 cGy. Fifty percent salivary dysfunction occurred after 1000 cGy and eighty percent dysfunction was observed by the end of the therapy course (6000 cGy). The salivary-function curve was also compared to the previously published dose-response curve for taste function. Comparisons of the two curves indicate that salivary dysfunction precedes taste loss and that the shapes of the dose-response curves are different. A new term, tissue tolerance ratio, defined as the ratio of responses of two tissues given the same radiation dose, was used to make the comparisons between gustatory and salivary gland tissue effects. Measurements of salivary gland function and analysis of dose-response curves may be useful in evaluating chemical modifiers of radiation response

Detection of irradiated spices using photo-stimulated luminescence technique (PSL)

Energy Technology Data Exchange (ETDEWEB)

Ramli, Ros Anita Ahmad; Yasir, Muhamad Samudi [Faculty of Science and Technology, National University of Malaysia, Bangi, 43000 Kajang, Selangor (Malaysia); Othman, Zainon; Abdullah, Wan Saffiey Wan [Malaysian Nuclear Agency, Bangi 43000 Kajang, Selangor (Malaysia)

2014-09-03

Photo-stimulated luminescence (PSL) technique was applied to detect irradiated black pepper (Piper nigrum), cinnamon (Cinnamomum verum) and turmeric (Curcuma longa) after dark storage for 1 day, 3 and 6 months. Using screening and calibrated PSL, all samples were correctly discriminated between non-irradiated and spices irradiated with doses 1, 5 and 10 kGy. The PSL photon counts (PCs) of irradiated spices increased with increasing dose, with turmeric showing highest sensitivity index to irradiation compared to black pepper and cinnamon. The differences in response are possibly attributed to the varying quantity and quality of silicate minerals present in each spice sample. PSL signals of all irradiated samples reduced after 3 and 6 months storage. The results of this study provide a useful database on the applicability of PSL technique for the detection of Malaysian irradiated spices.

Detection of irradiated spices using photo-stimulated luminescence technique (PSL)

International Nuclear Information System (INIS)

Ramli, Ros Anita Ahmad; Yasir, Muhamad Samudi; Othman, Zainon; Abdullah, Wan Saffiey Wan

2014-01-01

Photo-stimulated luminescence (PSL) technique was applied to detect irradiated black pepper (Piper nigrum), cinnamon (Cinnamomum verum) and turmeric (Curcuma longa) after dark storage for 1 day, 3 and 6 months. Using screening and calibrated PSL, all samples were correctly discriminated between non-irradiated and spices irradiated with doses 1, 5 and 10 kGy. The PSL photon counts (PCs) of irradiated spices increased with increasing dose, with turmeric showing highest sensitivity index to irradiation compared to black pepper and cinnamon. The differences in response are possibly attributed to the varying quantity and quality of silicate minerals present in each spice sample. PSL signals of all irradiated samples reduced after 3 and 6 months storage. The results of this study provide a useful database on the applicability of PSL technique for the detection of Malaysian irradiated spices

Detection of irradiated spices using photo-stimulated luminescence technique (PSL)

Science.gov (United States)

Ramli, Ros Anita Ahmad; Yasir, Muhamad Samudi; Othman, Zainon; Abdullah, Wan Saffiey Wan

2014-09-01

Photo-stimulated luminescence (PSL) technique was applied to detect irradiated black pepper (Piper nigrum), cinnamon (Cinnamomum verum) and turmeric (Curcuma longa) after dark storage for 1 day, 3 and 6 months. Using screening and calibrated PSL, all samples were correctly discriminated between non-irradiated and spices irradiated with doses 1, 5 and 10 kGy. The PSL photon counts (PCs) of irradiated spices increased with increasing dose, with turmeric showing highest sensitivity index to irradiation compared to black pepper and cinnamon. The differences in response are possibly attributed to the varying quantity and quality of silicate minerals present in each spice sample. PSL signals of all irradiated samples reduced after 3 and 6 months storage. The results of this study provide a useful database on the applicability of PSL technique for the detection of Malaysian irradiated spices.

A simple nondestructive technique for monitoring the bond gas in sealed fast reactor nuclear fuel pins

Energy Technology Data Exchange (ETDEWEB)

Shriwastwa, B B; Mehrotra, R S; Ghosh, J K [Bhabha Atomic Research Centre, Bombay (India). Radiometallurgy Div.

1994-12-31

A simple nondestructive testing technique has been developed to identify bond gas inside a welded fuel pin. The technique is based on the accurate surface temperature measurement of fuel pins heated in a constant temperature water bath. This technique can be applied in Fast Breeder Test Reactor (FBTR) fuel pin production line due to simplicity of the set up, simple operation and quick response time. An attempt was made to develop a non destructive test method for monitoring the bond gas composition. Preliminary development work carried out in this connection, the test method adopted and the test results are presented. 1 ref., 5 figs., 1 tab.

Human mixed lymphocyte cultures. Evaluation of microculture technique utilizing the multiple automated sample harvester (MASH)

Science.gov (United States)

Thurman, G. B.; Strong, D. M.; Ahmed, A.; Green, S. S.; Sell, K. W.; Hartzman, R. J.; Bach, F. H.

1973-01-01

Use of lymphocyte cultures for in vitro studies such as pretransplant histocompatibility testing has established the need for standardization of this technique. A microculture technique has been developed that has facilitated the culturing of lymphocytes and increased the quantity of cultures feasible, while lowering the variation between replicate samples. Cultures were prepared for determination of tritiated thymidine incorporation using a Multiple Automated Sample Harvester (MASH). Using this system, the parameters that influence the in vitro responsiveness of human lymphocytes to allogeneic lymphocytes have been investigated. PMID:4271568

Surveying and analyzing injection responses for patterns with horizontal wells

Energy Technology Data Exchange (ETDEWEB)

Fedenczuk, L.; Hoffman, K.

1998-12-31

A novel method for visualizing injection responses in patterns that include horizontal and/or vertical wells is described. Understanding fluid communication between the horizontal well and the surrounding injectors is essential to estimating the effectiveness of the waterflood. Armed with the understanding of responses, injection patterns can be optimized, production rates can be increased and more efficient oil recovery can be achieved. In this study the time lags of correlations and a new parameter, the waterflood response type is introduced. The response type is based on the oil and total fluid responses. In addition spider diagrams are introduced to help visualizing the correlations, time lags and response types. Integration of the results with geology, petrophysics and completion techniques can help to find the cause and effect rules in waterflood fields. 6 refs., 10 figs.

Laboratory techniques for human embryos.

Science.gov (United States)

Geber, Selmo; Sales, Liana; Sampaio, Marcos A C

2002-01-01

This review is concerned with laboratory techniques needed for assisted conception, particularly the handling of gametes and embryos. Such methods are being increasingly refined. Successive stages of fertilization and embryogenesis require especial care, and often involve the use of micromanipulative methods for intracytoplasmic sperm injection (ICSI) or preimplantation genetic diagnosis. Embryologists must take responsibility for gamete collection and preparation, and for deciding on the means of insemination or ICSI. Embryos must be assessed in culture, during the 1-cell, cleaving and morula/blastocyst stages, and classified according to quality. Co-culture methods may be necessary. The best embryos for transfer must be selected and loaded into the transfer catheter. Embryos not transferred must be cryopreserved, which demands the correct application of current methods of media preparation, seeding and the correct speed for cooling and warming. Before too long, methods of detecting abnormal embryos and avoiding their transfer may become widespread.

Optimization of MR fluid Yield stress using Taguchi Method and Response Surface Methodology Techniques

Science.gov (United States)

Mangal, S. K.; Sharma, Vivek

2018-02-01

Magneto rheological fluids belong to a class of smart materials whose rheological characteristics such as yield stress, viscosity etc. changes in the presence of applied magnetic field. In this paper, optimization of MR fluid constituents is obtained with on-state yield stress as response parameter. For this, 18 samples of MR fluids are prepared using L-18 Orthogonal Array. These samples are experimentally tested on a developed & fabricated electromagnet setup. It has been found that the yield stress of MR fluid mainly depends on the volume fraction of the iron particles and type of carrier fluid used in it. The optimal combination of the input parameters for the fluid are found to be as Mineral oil with a volume percentage of 67%, iron powder of 300 mesh size with a volume percentage of 32%, oleic acid with a volume percentage of 0.5% and tetra-methyl-ammonium-hydroxide with a volume percentage of 0.7%. This optimal combination of input parameters has given the on-state yield stress as 48.197 kPa numerically. An experimental confirmation test on the optimized MR fluid sample has been then carried out and the response parameter thus obtained has found matching quite well (less than 1% error) with the numerically obtained values.

Microrheometric upconversion-based techniques for intracellular viscosity measurements

Science.gov (United States)

Rodríguez-Sevilla, Paloma; Zhang, Yuhai; de Sousa, Nuno; Marqués, Manuel I.; Sanz-Rodríguez, Francisco; Jaque, Daniel; Liu, Xiaogang; Haro-González, Patricia

2017-08-01

Rheological parameters (viscosity, creep compliance and elasticity) play an important role in cell function and viability. For this reason different strategies have been developed for their study. In this work, two new microrheometric techniques are presented. Both methods take advantage of the analysis of the polarized emission of an upconverting particle to determine its orientation inside the optical trap. Upconverting particles are optical materials that are able to convert infrared radiation into visible light. Their usefulness has been further boosted by the recent demonstration of their three-dimensional control and tracking by single beam infrared optical traps. In this work it is demonstrated that optical torques are responsible of the stable orientation of the upconverting particle inside the trap. Moreover, numerical calculations and experimental data allowed to use the rotation dynamics of the optically trapped upconverting particle for environmental sensing. In particular, the cytoplasm viscosity could be measured by using the rotation time and thermal fluctuations of an intracellular optically trapped upconverting particle, by means of the two previously mentioned microrheometric techniques.

Simulation of limiting dilution technique in determination of immunocompetent cells frequency in irradiated cell cultures

International Nuclear Information System (INIS)

Martini Filho, R.J.; Barlette, V.E.; Goes, E.G.; Covas, D.T.; Orellana, M.

2001-01-01

Limiting dilution techniques (LDA) dose-response data have been used to detect immunocompetent T-Cells in microcultures. In this work, LDA frequencies estimates was obtained using χ2 minimization for irradiated cells in a range of 500 to 1,500 cGy. (author)

Radiofrequency ablation for hepatocellular carcinoma: assistant techniques for difficult cases.

Science.gov (United States)

Inoue, Tatsuo; Minami, Yasunori; Chung, Hobyung; Hayaishi, Sousuke; Ueda, Taisuke; Tatsumi, Chie; Takita, Masahiro; Kitai, Satoshi; Hatanaka, Kinuyo; Ishikawa, Emi; Yada, Norihisa; Hagiwara, Satoru; Ueshima, Kazuomi; Kudo, Masatoshi

2010-07-01

To confirm the safety and effectiveness of techniques to assist radiofrequency ablation (RFA) for difficult cases, we retrospectively evaluated successful treatment rates, early complications and local tumor progressions. Between June 1999 and April 2009, a total of 341 patients with 535 nodules were treated as difficult cases. Artificial pleural effusion assisted ablation was performed on 64 patients with 82 nodules. Artificial ascites-assisted ablation was performed on 11 patients with 13 nodules. Cooling by endoscopic nasobiliary drainage (ENBD) tube-assisted ablation was performed on 6 patients with 8 nodules. When the tumors were not well visualized with conventional B-mode ultrasonography (US), contrast-enhanced US-assisted ablation with Levovist or Sonazoid or virtual CT sonography-assisted ablation was performed. Contrast-enhanced US-assisted ablation was performed on 139 patients with 224 nodules and virtual CT sonography-assisted ablation was performed on 121 patients with 209 nodules. In total, complete ablation was achieved in 514 of 535 (96%) nodules in difficult cases. For RFA with artificial pleural effusion, artificial ascites and ENBD, complete response was confirmed in all cases. For contrast-enhanced US- and CT sonography-assisted ablation, complete response was 95%. Early complications were recognized in 24 cases (4.5%). All cases recovered with no invasive treatment. Local tumor recurrence was investigated in 377 nodules of 245 patients, and 69 (18%) nodules were positive. Tumor recurrences in each assisted technique were 14.7% in artificial pleural effusion cases, 7% in artificial ascites, 12.5% in ENBD tube cases, 31% in virtual CT sonography, and 8.5% in contrast-enhanced US. Although local tumor progression needs to be carefully monitored, assisted techniques of RFA for difficult cases are well tolerated and expand the indications of RFA. Copyright (c) 2010 S. Karger AG, Basel.

Application of magnetic resonance techniques for imaging tumour physiology

International Nuclear Information System (INIS)

Stubbs, M.

1999-01-01

Magnetic resonance (MR) techniques have the unique ability to measure in vivo the biochemical content of living tissue in the body in a dynamic, non-invasive and non-destructive manner. MR also permits serial investigations of steady-state tumour physiology and biochemistry, as well as the response of a tumour to treatment. Magnetic resonance imaging (MRI), Magnetic resonance spectroscopy (MRS) and a mixture of the two techniques (spectroscopic imaging) allow some physiological parameters, for example pH, to be 'imaged'. Using these methods, information on tissue bioenergetics and phospolipid membrane turnover, pH, hypoxia, oxygenation, and various aspects of vascularity including blood flow, angiogenesis, permeability and vascular volume can be obtained. In addition, MRS methods can be used for monitoring anticancer drugs (e.g. 5FU, ifosfamide) and their metabolites at their sites of action. The role of these state-of-the-art MR methods in imaging tumour physiology and their potential role in the clinic are discussed. (orig.)

Advanced experimental and numerical techniques for cavitation erosion prediction

CERN Document Server

Chahine, Georges; Franc, Jean-Pierre; Karimi, Ayat

2014-01-01

This book provides a comprehensive treatment of the cavitation erosion phenomenon and state-of-the-art research in the field. It is divided into two parts. Part 1 consists of seven chapters, offering a wide range of computational and experimental approaches to cavitation erosion. It includes a general introduction to cavitation and cavitation erosion, a detailed description of facilities and measurement techniques commonly used in cavitation erosion studies, an extensive presentation of various stages of cavitation damage (including incubation and mass loss), and insights into the contribution of computational methods to the analysis of both fluid and material behavior. The proposed approach is based on a detailed description of impact loads generated by collapsing cavitation bubbles and a physical analysis of the material response to these loads. Part 2 is devoted to a selection of nine papers presented at the International Workshop on Advanced Experimental and Numerical Techniques for Cavitation Erosion (Gr...

Multispectral fluorescence imaging techniques for nondestructive food safety inspection

Science.gov (United States)

Kim, Moon S.; Lefcourt, Alan M.; Chen, Yud-Ren

2004-03-01

The use of spectral sensing has gained acceptance as a rapid means for nondestructive inspection of postharvest food produce. Current technologies generally use color or a single wavelength camera technology. The applicability and sensitivity of these techniques can be expanded through the use of multiple wavelengths. Reflectance in the Vis/NIR is the prevalent spectral technique. Fluorescence, compared to reflectance, is regarded as a more sensitive technique due to its dynamic responses to subtle changes in biological entities. Our laboratory has been exploring fluorescence as a potential means for detection of quality and wholesomeness of food products. Applications of fluorescence sensing require an understanding of the spectral characteristics emanating from constituents and potential contaminants. A number of factors affecting fluorescence emission characteristics are discussed. Because of relatively low fluorescence quantum yield from biological samples, a system with a powerful pulse light source such as a laser coupled with a gated detection device is used to harvest fluorescence, in the presence of ambient light. Several fluorescence sensor platforms developed in our laboratory, including hyperspectral imaging, and laser-induced fluorescence (LIF) and steady-state fluorescence imaging systems with multispectral capabilities are presented. We demonstrate the potential uses of recently developed fluorescence imaging platforms in food safety inspection of apples contaminated with animal feces.

Effect of Ceramic Scaffold Architectural Parameters on Biological Response