Report on the 1984 LBL workshop on detectors for relativistic nuclear collisions

International Nuclear Information System (INIS)

Schroeder, L.S.

1984-11-01

Highlights of the Workshop on Detectors for Relativistic Nuclear Collisions, held March 26-30, 1984, at the Lawrence Berkeley Laboratory are reviewed. (Complete proceedings are available as report LBL-18225.)

Resource Room Model for Inclusive Education in China: Practitioners' Conceptualisation and Contextualisation

Science.gov (United States)

Poon-McBrayer, Kim Fong

2016-01-01

China launched the "learning in a regular classroom" (LRC) model for inclusive education in the 1980s. In late 1990s, a few major cities of China began to adopt the resource room model as a key feature of the LRC to improve instructional qualities. This exploratory study examined resource teachers' (RTs) attitude towards inclusive…

Graphene-based LbL deposited films: further study of electrical and gas sensing properties

Directory of Open Access Journals (Sweden)

Nabok A.

2017-01-01

Full Text Available Graphene-surfactant composite materials obtained by the ultrasonic exfoliation of graphite powder in the presence of ionic surfactants (either CTAB or SDS were utilised to construct thin films using layer-by-layer (LbL electrostatic deposition technique. A series of graphene-based thin films were made by alternating layers of either graphene-SDS with polycations (PEI or PAH or graphene-CTAB with polyanions (PSS. Also, graphene-phthalocyanine composite films were produced by alternating layers of graphene-CTAB with tetrasulfonated nickel phthalocyanine. Graphene-surfactant LbL films exhibited good electric conductivity (about 0.1 S/cm of semiconductor type with a band gap of about 20 meV. Judging from UV-vis spectra measurements, graphene-phthalocyanine LbL films appeared to form joint π-electron system. Gas sensing testing of such composite films combining high conductivity of graphene with the gas sensing abilities of phthalocyanines showed substantial changes (up to 10% in electrical conductivity upon exposure to electro-active gases such as HCl and NH3.

16 CFR Appendix E to Part 305 - Room Air Conditioners

Science.gov (United States)

2010-01-01

... 16 Commercial Practices 1 2010-01-01 2010-01-01 false Room Air Conditioners E Appendix E to Part 305 Commercial Practices FEDERAL TRADE COMMISSION REGULATIONS UNDER SPECIFIC ACTS OF CONGRESS RULE... Appendix E to Part 305—Room Air Conditioners Range Information Manufacturer's rated cooling capacity in Btu...

Vacuum ARC ion sources - activities ampersand developments at LBL

International Nuclear Information System (INIS)

Brown, I.

1996-01-01

The author describes work at LBL on the development and application of vacuum arc ion sources. Work has been done on vacuum spark sources - to produce very high charge states, studies of high charge states in magnetic field, hybrid ion source operation on metal/gas plasma, multipole operation, work on MEVVA V for implantation applications, development of broad beam sources, and removal of particles from the output of the source

Immobilization of cholesterol oxidase in LbL films and detection of cholesterol using ac measurements

International Nuclear Information System (INIS)

Moraes, Marli L.; Souza, Nara C. de; Hayasaka, Caio O.; Ferreira, Marystela; Rodrigues Filho, Ubirajara P.; Riul, Antonio; Zucolotto, Valtencir; Oliveira, Osvaldo N.

2009-01-01

The preserved activity of immobilized biomolecules in layer-by-layer (LbL) films can be exploited in various applications, including biosensing. In this study, cholesterol oxidase (COX) layers were alternated with layers of poly(allylamine hydrochloride) (PAH) in LbL films whose morphology was investigated with atomic force microscopy (AFM). The adsorption kinetics of COX layers comprised two regimes, a fast, first-order kinetics process followed by a slow process fitted with a Johnson-Mehl-Avrami (JMA) function, with exponent ∼ 2 characteristic of aggregates growing as disks. The concept based on the use of sensor arrays to increase sensitivity, widely employed in electronic tongues, was extended to biosensing with impedance spectroscopy measurements. Using three sensing units, made of LbL films of PAH/COX and PAH/PVS (polyvinyl sulfonic acid) and a bare gold interdigitated electrode, we were able to detect cholesterol in aqueous solutions down to the 10 -6 M level. This high sensitivity is attributed to the molecular-recognition interaction between COX and cholesterol, and opens the way for clinical tests to be made with low cost, fast experimental procedures

Debittering of Protein Hydrolysates by Lactobacillus LBL-4 Aminopeptidase

Directory of Open Access Journals (Sweden)

Bozhidar Tchorbanov

2011-01-01

Full Text Available Yoghurt strain Lactobacillus LBL-4 cultivated for 8–10 h at pH ~6.0 was investigated as a considerable food-grade source of intracellular aminopeptidase. Cell-free extract manifesting >200 AP U/l was obtained from cells harvested from 1 L culture media. Subtilisin-induced hydrolysates of casein, soybean isolate, and Scenedesmus cell protein with degree of hydrolysis 20–22% incubated at 45∘C for 10 h by 10 AP U/g peptides caused an enlarging of DH up to 40–42%, 46–48%, and 38–40% respectively. The DH increased rapidly during the first 4 h, but gel chromatography studies on BioGel P-2 showed significant changes occurred during 4–10 h of enzyme action when the DH increased gradually. After the digestion, the remained AP activity can be recovered by ultrafiltration (yield 40–50%. Scenedesmus protein hydrolysate with DH 20% was inoculated by Lactobacillus LBL-4 cells, and after 72 h cultivation the DH reached 32%. The protein hydrolysates (DH above 40% obtained from casein and soybean isolate (high Q value demonstrated a negligible bitterness while Scenedesmus protein hydrolysates (low Q value after both treatments were free of bitterness.

Beam-beam studies for the proposed SLAC/LBL/LLNL B Factory

International Nuclear Information System (INIS)

Furman, M.A.

1991-05-01

We present a summary of beam-beam dynamics studies that have been carried out to date for the proposed SLAC/LBL/LLNL B Factory. Most of the material presented here is contained in the proposal's Conceptual Design Report, although post-CDR studies are also presented. 15 refs., 6 figs., 2 tabs

Status of the LBL/LLL development program

International Nuclear Information System (INIS)

Berkner, K.H.; Cooper, W.S.; Ehlers, K.W.; Pyle, R.V.; Hooper, E.B. Jr.

1977-11-01

The status and near-term goals of the LBL/LLL neutral-beam-development program are described. The emphasis is on the technology of systems based on the acceleration and neutralization of positive ions; this approach will be used in the near term, probably through 1985 at least. For more efficient injection, part of the plan is to develop a negative-ion approach suitable for 200- to 400-kV injectors on confinement experiments in the 1985 to 1990 period. However, the negative-ion based program is still very much in the research phase, and it is difficult to project how it will phase into fusion reactor fueling experiments

Status of the LBL/LLL development program

International Nuclear Information System (INIS)

Berkner, K.H.; Cooper, W.S.; Ehlers, K.W.; Pyle, R.V.; Hooper, E.B. Jr.

1978-01-01

The status and near-term goals of the LBL/LLL neutral-beam-development program are described. The emphasis in this paper is on the technology of systems based on the acceleration and neutralization of positive ions; this approach will be used in the near term, probably through 1985 at least. For more efficient injection, part of our plan is to develop a negative-ion approach suitable for 200- to 400-kV injectors on confinement experiments in the 1985 to 1990 period. However, the negative-ion based program is still very much in the research phase, and it is difficult to project how it will phase into fusion reactor fueling experiments

Positive ion portion of the LBL/LLL Neutral Beam Program

International Nuclear Information System (INIS)

Pyle, R.V.; Baker, W.R.; Anderson, O.A.

1978-06-01

The positive ion portion of the Neutral Beam Development Program at the Lawrence Berkeley (LBL) and Livermore (LLL) Laboratories has two purposes: (a) to carry out general research and development in a timely way to assure that users' needs can be met in principle, and (b) to carry out specific development for users. To meet the first requirement, we have programs to develop sources capable of producing beams with high (85%) atomic fractions, long pulse lengths (10 sec to DC), and at beam energies up to 150 keV. We are also pursuing the development of on-line computer diagnostics and controls, the sophisticated high-power electronics required by neutral beam systems, and energy recovery. To meet the second requirement, we are developing prototype source modules to meet the requirements of the TMX and MFTF experiments at Lawrence Livermore Laboratory, the TFTR experiment at the Princeton Plasma Physics Laboratory, and the Doublet III experiment at General Atomic Co. The Lawrence Laboratories are also constructing and will demonstrate at LBL a complete prototype neutral injection system for TFTR, and are designing a similar system for Doublet III

Metal ion reactive thin films using spray electrostatic LbL assembly.

Science.gov (United States)

Krogman, Kevin C; Lyon, Katharine F; Hammond, Paula T

2008-11-20

By using the spray-layer-by-layer (Spray-LbL) technique, the number of metal counterions trapped within LbL coatings is significantly increased by kinetically freezing the film short of equilibrium, potentially limiting interchain penetration and forcing chains to remain extrinsically compensated to a much greater degree than observed in the traditional dipped LbL technique. The basis for the enhanced entrapment of metal ions such as Cu2+, Fe2+, and Ag+ is addressed, including the equilibrium driving force for extrinsic compensation by soft versus hard metal ions and the impact of Spray-LbL on the kinetics of polymer-ion complexation. These polymer-bound metal-ion coatings are also demonstrated to be effective treatments for air filtration, functionalizing existing filters with the ability to strongly bind toxic industrial compounds such as ammonia or cyanide gases, as well as chemical warfare agent simulants such as chloroethyl ethyl sulfide. On the basis of results reported here, future work could extend this method to include other toxic soft-base ligands such as carbon monoxide, benzene, or organophosphate nerve agents.

LBL/UCSB 76Ge double beta decay experiment: first results

International Nuclear Information System (INIS)

Goulding, F.S.; Cork, C.P.; Landis, D.A.

1984-10-01

A paper given at the IEEE Nuclear Science Symposium last year presented the scientific justification for this experiment and discussed the design of the detector system. At the present time two of the dual detector systems (i.e., four out of a final total of eight detectors) are operating in the complete active/passive shield in the low background laboratory at LBL. Early results (1620 h) of an experiment using two detectors yield a limit of 4 x 10 22 years (68% confidence) for the half life of the neutrinoless double beta decay (ββ/sub o nu/) of 76 Ge. Although this experiment was carried out above ground, the result approaches those achieved by other groups in deep underground laboratories. Based on studies of the origins of background in our system, we hope to reach a limit of 3 x 10 23 years (or more) in a two month/four detector experiment to be carried out soon in an underground facility

LBL/JSU/AGMUS science consortium annual report, FY 1991--1992

Energy Technology Data Exchange (ETDEWEB)

1992-12-31

In 1983, a formal Memorandum of Understanding joined the Ana G. Mendez University System (AGMUS), Jackson State University (JSU), and the Lawrence Berkeley Laboratory (LBL) in a consortium designed to advance the science and technology programs of JSU and AGMUS. This is the first such collaboration between a Hispanic university system, a historically Black university, and a national laboratory. The goals of this alliance are basic and direct: to develop and effect a long-term, comprehensive program that will enable the campuses of AGMUS and JSU to provide a broad, high-quality offering in the natural and computer sciences, to increase the number of minority students entering these fields, and to contribute to scientific knowledge and the federal government`s science mission through research. This report documents the progress toward these goals and includes individual success stories. The LBL/JSU/AGMUS Science Consortium has developed plans for utilizing its program successes to help other institutions to adopt or adapt those elements of the model that have produced the greatest results. Within the five-year plan formulated in 1990 are eight major components, each with defining elements and goals. These elements have become the components of the Science Consortium`s current plan for expansion and propagation.

Linear collider research and development at SLAC, LBL and LLNL

International Nuclear Information System (INIS)

Mattison, T.S.

1988-10-01

The study of electron-positron (e + e/sup /minus//) annihilation in storage ring colliders has been very fruitful. It is by now well understood that the optimized cost and size of e + e/sup /minus// storage rings scales as E(sub cm//sup 2/ due to the need to replace energy lost to synchrotron radiation in the ring bending magnets. Linear colliders, using the beams from linear accelerators, evade this scaling law. The study of e/sup +/e/sup /minus// collisions at TeV energy will require linear colliders. The luminosity requirements for a TeV linear collider are set by the physics. Advanced accelerator research and development at SLAC is focused toward a TeV Linear Collider (TLC) of 0.5--1 TeV in the center of mass, with a luminosity of 10/sup 33/--10/sup 34/. The goal is a design for two linacs of less than 3 km each, and requiring less than 100 MW of power each. With a 1 km final focus, the TLC could be fit on Stanford University land (although not entirely within the present SLAC site). The emphasis is on technologies feasible for a proposal to be framed in 1992. Linear collider development work is progressing on three fronts: delivering electrical energy to a beam, delivering a focused high quality beam, and system optimization. Sources of high peak microwave radio frequency (RF) power to drive the high gradient linacs are being developed in collaboration with Lawrence Berkeley Laboratory (LBL) and Lawrence Livermore National Laboratory (LLNL). Beam generation, beam dynamics and final focus work has been done at SLAC and in collaboration with KEK. Both the accelerator physics and the utilization of TeV linear colliders were topics at the 1988 Snowmass Summer Study. 14 refs., 4 figs., 1 tab

Improving 900 MW(e) PWR control rooms

International Nuclear Information System (INIS)

Bouat, M.; Marcille, R.

1983-01-01

Analyses of the behaviour of operators during operating tests on PWR units and the lessons learned from the TMI-2 accident have demonstrated the need to improve the interface between operators and the facilities they control. To that end, and to complement its establishment of safety panels, Electricite de France (EDF) embarked upon a study on the ''Modification of Control Desks and Boards'' in control rooms. This study, involving twenty-eight 900 MW(e) units, almost all of which are currently in service, began with an ergonomic analysis of control rooms by an external consultant, the ADERSA GERBIOS Association. This analysis was based on interviews with simulator instructors and operators, a study of the operation of the unit, and a general review of previous studies. The analysis began in October 1980 and resulted, in April 1981, in a critical report and a proposal to create a full-scale mock-up of a 900 MW(e) control room. Improvements to this were subsequently proposed, enabling options to be made between, among other things, active overall control panels and function-by-function control panels. Finally, a number of general principles, which largely encompass the operators' suggestions, were defined. The alterations to be made will make it necessary to revamp the control panels completely. The work and tests involved should match the duration of refuelling shut-downs. Audio-visual training programmes are planned (portable model). (author)

Status of the SLAC/LBL/LLNL B-factory and the BABAR detector

International Nuclear Information System (INIS)

Oddone, P.

1994-10-01

After a brief introduction on the physics reach of the SLAC/LBL/LLNL Asymmetric B-Factory, the author describes the status of the accelerator and the detector as of the end of 1994. At this time, essentially all major decisions have been made, including the choice of particle identification for the detector. The author concludes this report with the description of the schedule for the construction of both accelerator and detector

Multi-beam injector development at LBL

International Nuclear Information System (INIS)

Rutkowski, H.L.; Faltens, A.; Brodzik, D.A.; Johnson, R.M.; Pike, C.D.; Vanecek, D.L.; Humphries, S. Jr.; Meyer, E.A.; Hewett, D.W.

1990-06-01

LBL is developing a multi-beam injector that will be used for scaled accelerator experiments related to Heavy Ion Fusion. The device will produce sixteen 0.5 Amp beams of C+ at 2 MeV energy. The carbon arc source has been developed to the point where the emittance is within a factor of four of the design target. Modelling of the source behavior to find ways to reduce the emittance is discussed. Source lifetime and reliability is also of paramount importance to us and data regarding the lifetime and failure modes of different source configurations is discussed. One half of the accelerating column has been constructed and tested at high voltage. One beam experiments in this half column are underway. The second half of the column is being built and the transition 2 MV experiments should begin soon. In addition to beam and source performance we also discuss the controls for the injector and the electronics associated with the source and current injection. 3 refs., 2 figs

Long-pulse neutral beam power supply system for LBL 20 kV, 10 A sources

International Nuclear Information System (INIS)

Honey, V.J.; Baker, W.R.; Fitzgerald, M.L.

1976-05-01

A description is given of the power supplies and control system for the LBL 20 kV, 10 A, 10 sec long-pulse neutral beam source test facility, now in operation. Such sources are used in a number of existing and planned fusion power experiments

A fragment separator at LBL for beta-NMR experiment

International Nuclear Information System (INIS)

Matsuta, K.; Ozawa, A.; Nojiri, Y.; Minamisono, T.; Fukuda, M.; Kitagawa, A.; Ohtsubo, T.; Momota, S.; Fukuda, S.; Matsuo, Y.; Takechi, H.; Minami, I.; Sugimoto, K.; Tanihata, I.; Omata, K.; Alonso, J.R.; Krebs, G.F.; Symons, T.J.M.

1992-03-01

The Beam 44 fragment separator was built at the Bevalac of LBL for NMR studies of beta emitting nuclei. 37 K, 39 Ca, and 43 Ti fragments originating from 40 Ca and 46 Ti primary beams were separated by the separator for NMR studies on these nuclei. Nuclear spin polarization was created in 39 Ca and 43 Ti using the tilted foil technique (TFT), and the magnetic moment of 43 Ti was deduced. Fragment polarization was measured for 37 K and 39 Ca emitted to finite deflection angles. The Beam 44 fragment separator in combination with a proper polarization technique, such as TFT or fragment polarization, has been very effective for such NMR studies

First experimental results from IBM/TENN/TULANE/LLNL/LBL undulator beamline at the advanced light source

International Nuclear Information System (INIS)

Jia, J.J.; Callcott, T.A.; Yurkas, J.; Ellis, A.W.; Himpsel, F.J.; Samant, M.G.; Stoehr, J.; Ederer, D.L.; Carlisle, J.A.; Hudson, E.A.; Terminello, L.J.; Shuh, D.K.; Perera, R.C.C.

1995-01-01

The IBM/TENN/TULANE/LLNL/LBL Beamline 8.0 at the advanced light source combining a 5.0 cm, 89 period undulator with a high-throughput, high-resolution spherical grating monochromator, provides a powerful excitation source over a spectral range of 70--1200 eV for surface physics and material science research. The beamline progress and the first experimental results obtained with a fluorescence end station on graphite and titanium oxides are presented here. The dispersive features in K emission spectra of graphite excited near threshold, and found a clear relationship between them and graphite band structure are observed. The monochromator is operated at a resolving power of roughly 2000, while the spectrometer has a resolving power of 400 for these fluorescence experiments

Fast track-finding trigger processor for the SLAC/LBL Mark II Detector

International Nuclear Information System (INIS)

Brafman, H.; Breidenbach, M.; Hettel, R.; Himel, T.; Horelick, D.

1977-10-01

The SLAC/LBL Mark II Magnetic Detector consists of various particle detectors arranged in cylindrical symmetry located in and around an axial magnetic field. A versatile, programmable secondary trigger processor was designed and built to find curved tracks in the detector. The system operates at a 10 MHz clock rate with a total processing time of 34 μsec and is used to ''trigger'' the data processing computer, thereby rejecting background and greatly improving the data acquisition aspects of the detector-computer combination

LBL coating of type I collagen and hyaluronic acid on aminolyzed PLLA to enhance the cell-material interaction

Directory of Open Access Journals (Sweden)

M. Y. Zhao

2014-05-01

Full Text Available The aim of the present work is to assemble extracellular matrix components onto poly (L-lactic acid (PLLA films using layer-by-layer (LBL depositing method to enhance the cell-material interaction. To introduce charges onto the hydrophobic and neutral PLLA surface so that the electronic assembly can be processed, poly (ethylene imine (PEI was covalently bonded to modify the PLLA films. Positively charged collagen I (Col I was then deposited onto the aminolyzed PLLA film surface in a LBL assembly manner using hyaluronic acid (HA as a negatively charged polyelectrolyte. The PEI modification efficiency was monitored via X-ray photoelectron spectroscopy (XPS measurements. The results of Surface Plasmon Resonance (SPR and Water contact angle (WCA monitoring the LBL assemble process presented that the HA/Col I deposited alternately onto the PLLA surface. The surface topography of the films was observed by Atomic force microscope (AFM. In vitro osteoblast culture found that the presence of Col I layer greatly improved the cytocompatibility of the PLLA films in terms of cell viability, cell proliferation and Alkaline Phosphatase (ALP expression. Furthermore, osteoblast extensions were found to be directed by contact guidance of the aligned Col I fibrils. Thus, these very flexible systems may allow broad applications for improve the bioactivity of polymeric materials, which might be a potential application for bone tissue engineering.

Data acquisition using PDP-11 and MBD branch driver at L.B.L

International Nuclear Information System (INIS)

Harvey, E.H. Jr.

1979-05-01

A data acquisition system was designed and preliminary versions implemented for physics experiments at LBL. It utilizes an MBD microprogramed branch driver and a PDP-11 operating under RSM-11M. An MBD executive is used to implement software breakpoints within the MBD. The PDP-11 data acquisition buffer management scheme allows for multiple tasks dynamically accessing the data stream. Emphasis is directed towards future expansions. High data rates are also emphasized. 2 tables

Electrostatic probe diagnostics on the LBL 10 ampere neutral beam ion source

International Nuclear Information System (INIS)

Schoenberg, K.F.

1978-08-01

The experimental results of electrostatic probe measurements on the LBL 10 ampere ion source are presented. Data is obtained via a pulsed acquisition system which digitally records a probe characteristic and its first and second derivatives. The latter are shown to be proportional to the projected electron energy distribution function, and the isotropic electron energy distribution function, respectively. System performance for distribution function measurement is compared to the established technique of harmonic analysis. A complete analysis of the data acquisition system and its experimental accuracy is presented

Guidelines for Waste Accumulation Areas (WAAs) at LBL. Revision 1

International Nuclear Information System (INIS)

1994-01-01

The purpose of this document is to set conditions for establishing and containing areas for the accumulation of hazardous waste at LBL. Areas designed for accumulation of these wastes for up to 90 days in quantities greater than 55 gallons (208 liters) of hazardous waste, one quart (0.946 liter) of extremely hazardous waste, or one quart (0.946 liter) of acutely hazardous waste are called Waste Accumulation Areas (WAAs). Areas designed for accumulation of wastes in smaller amounts are called Satellite Accumulation Areas (SAAs). This document provides guidelines for employee and organizational responsibilities for WAAs, constructing a WAA, storing waste in a WAA, operating and maintaining a WAA, and responding to spills in a WAA

Effect of manufacturing errors on field quality of the LBL SSC dipoles

International Nuclear Information System (INIS)

Meuser, R.B.

1984-01-01

A method is developed for determining the field aberrations resulting from specific kinds of manufacturing errors. This method is applied to the 40-mm i.d. dipoles under consideration at LBL, and also to similar ones with 30 and 50 mm i.d. The method is also applied to the CBA and Doubler/Saver magnets and the results compared with the measurements. The results obtained by this method are also compared with those obtained by assigning identical errors to the positions of the edges of all the coil sectors

Crew resource management: using aviation techniques to improve operating room safety.

Science.gov (United States)

Ricci, Michael A; Brumsted, John R

2012-04-01

Since the publication of the Institute of Medicine report estimating nearly 100,000 deaths per year from medical errors, hospitals and physicians have a renewed focus upon error reduction. We implemented a surgical crew resource management (CRM) program for all operating room (OR) personnel. In our academic medical center, 19,000 procedures per year are performed in 27 operating rooms. Mandatory CRM training was implemented for all peri-operative personnel. Aviation techniques introduced included a pre-operative checklist and brief, post-operative debrief, read and initial files, and various other aviation-based techniques. Compliance with conduct of the brief/debrief was monitored as well as wrong-site surgeries and retained foreign body events. The malpractice insurance database for claims was also queried for the period prior to and after training. Initial training was accomplished for 517 people, including all anesthesiologists, surgeons, nurses, technicians, and OR assistants. Pre-operative briefing increased from 6.7 to 99% within 4 mo. Wrong site surgeries and retained foreign bodies decreased from a high of seven in 2007 to none in 2008, but, after 14 mo without additional training, these rose to five in 2009. Malpractice expenses (payouts and legal fees) totaled $793,000 (2003-2007), but have been zero since 2008. CRM training and implementation had an impact on reducing the incidence of wrong site surgery and retained foreign bodies in our operating rooms. However, constant reinforcement and refresher training is necessary for sustained results. Though no one technique can prevent all errors, CRM can effect culture change, producing a safer environment.

e-Learning Resource Brokers

NARCIS (Netherlands)

Retalis, Symeon; Papasalouros, Andreas; Avgeriou, Paris; Siassiakos, Kostas

2004-01-01

There is an exponentially increasing demand for provisioning of high-quality learning resources, which is not satisfied by current web technologies and systems. E-Learning Resource Brokers are a potential solution to this problem, as they represent the state-of-the-art in facilitating the exchange

Studies at LBL's Bevalac will help resolve uncertainties about radiation risks to astronauts

International Nuclear Information System (INIS)

Kahn, J.

1991-01-01

Plans to operate the LBL's Bevalac facility for space research are discussed. The proposed program includes the use of cell cultures and animal models to assess the biological consequences of exposures to different particles that are components of the space radiation environment. Research will also be conducted on measures to counter radiation. Experiments will be carried out to examine how various materials that could be used in a spacecraft wall would alter the cascade of particles that would ultimately reach an astronaut

Overview of the LBL/LLNL negative-ion-based neutral beam program

International Nuclear Information System (INIS)

Pyle, R.V.

1980-01-01

The LBL/LLNL negative-ion-based neutral beam development program and status are described. The emphasis has shifted in some details since the first symposium in 1977, but our overall objectives remain the same, namely, the development of megawatt d.c. injection systems. Previous emphasis was on a system in which the negative ions were produced by double charge exchange in sodium vapor. At present, the emphasis is on a self-extraction source in which the negative ions are produced on a biased surface imbedded in a plasma. A one-ampere beam will be accelerated to at least 40 keV next year. Studies of negative-ion formation and interactions help provide a data base for the technology program

Effects of undulators on the ALS: The early work on the LBL [Lawrence Berkeley Laboratory

International Nuclear Information System (INIS)

Jackson, A.

1988-05-01

In this paper we describe the early work carried out at LBL on the consequences of installing insertion devices (wigglers and undulators) on the beam dynamics of the ALS. This included analytical and tracking studies, and led to an insight to the reasons behind the predicted reduction in dynamic aperture. For completeness, a description of the unperturbed storage ring characteristics are also given. 3 refs., 16 figs., 2 tabs

Ground motion measurements at the LBL Light Source site, the Bevatron and at SLAC

International Nuclear Information System (INIS)

Green, M.A.; Majer, E.I.; More, V.D.; O'Connell, D.R.; Shilling, R.C.

1986-12-01

This report describes the technique for measuring ground motion at the site of the 1.0 to 2.0 GeV Synchrotron Radiation Facility which was known as the Advanced Light Source (in 1983 when the measurements were taken). The results of ground motion measurements at the Light Source site at Building 6 at LBL are presented. As comparison, ground motion measurements were made at the Byerly Tunnel, the Bevatron, Blackberry Canyon, and SLAC at the Spear Ring. Ground Motion at the Light Source site was measured in a band from 4 to 100 Hz. The measured noise is primarily local in origin and is not easily transported through LBL soils. The background ground motion is for the most part less than 0.1 microns. Localized truck traffic near Building 6 and the operation of the cranes in the building can result in local ground motions of a micron or more for short periods of time. The background motion at Building 6 is between 1 and 2 orders of magnitude higher than ground motion in a quiet seismic tunnel, which is representative of quiet sites worldwide. The magnitude of the ground motions at SLAC and the Bevatron are comparable to ground motions measured at the Building 6 Light Source site. However, the frequency signature of each site is very different

Vacuum system for the LBL Advanced Light Source (ALS)

International Nuclear Information System (INIS)

Kennedy, K.; Henderson, T.; Meneghetti, J.

1989-03-01

A 1.5 to 1.9 GeV synchrotron light source is being built at LBL. The vacuum system is designed to permit most synchrotron photons to escape the electron channel and be absorbed in an antechamber. The gas generated by the photons hitting the absorbers in the antechambers will be pumped by titanium sublimation pumps located directly under the absorbers. The electron channel and the antechamber are connected by a 10-mm-high slot that offers good electrodynamic isolation of the two chambers of frequencies affecting the store electron orbit. Twelve 10-meter-long vessels constitute the vacuum chambers for all the lattice magnets. Each chamber will be machined from two thick plates of 5083-H321 aluminum and welded at the perimeter. Machining both the inside and outside of the vacuum chamber permits the use of complex and accurate surfaces. The use of thick plates allows flanges to be machined directly into the wall of each chamber, thus avoiding much welding. 1 ref., 3 figs

The 50 MeV Beam Test Facility at LBL

International Nuclear Information System (INIS)

Leemans, W.; Behrsing, G.; Kim, K.J.; Krupnick, J.; Matuk, C.; Selph, F.; Chattopadhyay, S.

1993-05-01

A new beam line, expected to be built by September 1993, will transport the 50 MeV electron beam from the ALS LINAC into an experimental area to support various R ampersand D activities in the Center for Beam Physics at LBL. A variety of experiments are planned involving the interaction of such a relativistic electron beam with plasmas (plasma focusing), laser beams (generation of femtosecond X-ray pulses) and electromagnetic cavities (Crab cavities etc....). The beam line is designed using the measured emittance and Twiss parameters of the ALS linac. It accommodates the different requirements of the various experiments on the electron beam properties (charge, energy, pulse length) and on the handling of the beam before and after the interaction point. Special attention has also been given to incorporate diagnostics for measuring the beam properties (such as the electron energy, bunch length and charge) needed in the interpretation of the experiments

Ionization, charge exchange, and secondary electron emission in the extractor of an LBL/LLL neutral beam source

International Nuclear Information System (INIS)

Fink, J.H.; McDowell, C.E.

1975-01-01

Using a computer code, bombardment of the electrodes resulting from ionization, charge-exchange, and back-ion emission from the neutralizer cell is studied in the positive-ion extractor region of a Lawrence Berkeley Laboratory/Lawrence Livermore Laboratory (LBL/LLL) neutral beam source. Ion and electron trajectories are presented, grid dissipations estimated, and proposals made for future designs

Ação pedagógica e educação especial: a sala de recursos como prioridade na oferta de serviços especializados Pedagogical action and special education: special education resource room as priority in offering specialized services

Directory of Open Access Journals (Sweden)

Claudio Roberto Baptista

2011-08-01

Full Text Available o objetivo do presente texto é apresentar reflexões acerca da ação pedagógica e dos serviços especializados em Educação Especial, no contexto brasileiro. Busca-se dar destaque a um debate sobre as tendências, as características e os desafios que marcam a oferta de serviços educacionais, assim como a ação dos educadores especializados. A presente análise pretende contribuir para a compreensão sobre como ocorreram alterações políticas que resultam no avanço da sala de recursos como serviço prioritário para a política educacional brasileira no que se refere à garantia de Atendimento Educacional Especializado aos alunos com deficiência, transtornos globais do desenvolvimento e altas habilidades/superdotação. Quais são os desafios associados à sala de recursos como espaço escolar e como dispositivo pedagógico? Como os estudos contemporâneos têm se ocupado de analisar as recentes experiências no contexto nacional? Nestas reflexões são considerados: o fortalecimento da inclusão escolar como diretriz política para a educação brasileira; as indicações, em termos de documentos legais e orientadores, para a constituição dos serviços; o debate acadêmico quanto à necessidade de avanços na qualificação das salas de recursos, indicando a necessária difusão do conhecimento produzido e a intensificação de sua deriva pedagógica nas relações com o currículo e com a ação docente em geral.The aim of this paper is to present reflections on the pedagogical action and specialized services in Special Education in Brazil. The aim is to discuss trends, characteristics and challenges that feature Brazilian educational services supply as well as the action of specialist teachers. This analysis aims to contribute to the understanding of how educational policies have changed and how these changes took the Special Education Resource Room to a priority service level in the Brazilian educational policy, regarding

Inverse modeling as a step in the calibration of the LBL-USGS site-scale model of Yucca Mountain

International Nuclear Information System (INIS)

Finsterle, S.; Bodvarsson, G.S.; Chen, G.

1995-05-01

Calibration of the LBL-USGS site-scale model of Yucca Mountain is initiated. Inverse modeling techniques are used to match the results of simplified submodels to the observed pressure, saturation, and temperature data. Hydrologic and thermal parameters are determined and compared to the values obtained from laboratory measurements and conventional field test analysis

Crisis Resource Management in the Delivery Room: Development of Behavioral Markers for Team Performance in Emergency Simulation.

Science.gov (United States)

Bracco, Fabrizio; de Tonetti, Gabriele; Masini, Michele; Passarelli, Marcello; Geretto, Francesca; Celleno, Danilo

2018-03-03

Human factors are the most relevant issues contributing to adverse events in obstetrics. Specific training of Crisis Resource Management (CRM) skills (i.e., problem solving and team management, resource allocation, awareness of environment, and dynamic decision-making) is now widespread and is often based on High Fidelity Simulation. In order to be used as a guideline in simulated scenarios, CRM skills need to be mapped to specific and observable behavioral markers. For this purpose, we developed a set of observable behaviors related to the main elements of CRM in the delivery room. The observational tool was then adopted in a two-days seminar on obstetric hemorrhage where teams working in obstetric wards of six Italian hospitals took part in simulations. The tool was used as a guide for the debriefing and as a peer-to-peer feedback. It was then rated for its usefulness in facilitating the reflection upon one's own behavior, its ease of use, and its usefulness for the peer-to-peer feedback. The ratings were positive, with a median of 4 on a 5-point scale. The CRM observational tool has therefore been well-received and presents a promising level of inter-rater agreement. We believe the tool could have value in facilitating debriefing and in the peer-to-peer feedback.

Automatic tuning of the LBL SuperHILAC third-injector transport line

Energy Technology Data Exchange (ETDEWEB)

Pines, H.

1983-03-01

Testing of a new automatic tuning procedure in an LBL SuperHILAC beam transport line has been conducted with the third injector microcomputer control system. This technique is an advance over the sequential station-by-station automatic tuning method developed for the Bevalac transfer line. The computer now performs steering/focusing adjustments simultaneously on a number of quadrupole and dipole magnets comprising multiple-station sections of the injection line. New magnet currents are computed from equations governing beam optics in a real-time simulation of the beam line. The key to this emittance utilizing the same control magnets and beam profile monitors used for manual tuning of the line. This emittance calculation requires high resolution beam profile measurements using multi-wire profile monitors recently installed in the third injector line.

Production of exotic beams at the LBL 88-Inch Cyclotron by the ISOL method

International Nuclear Information System (INIS)

1990-04-01

The Users of the LBL 88-Inch Cyclotron are preparing a proposal to produce exotic, i.e., radioactive beams. The facility will consist of a high-current 30 MeV cyclotron to generate the radioactive nuclei, an ECR source that can be coupled to different production targets, and the 88-Inch Cyclotron to accelerate the radioactive ions. Thus, the basic concept is that of the double cyclotron system pioneered at Louvain-la-Neuve, although the initial emphasis will be on producing a variety of light proton-rich beams at energies up to 10 MeV/A. At this workshop we wish to outline what is being planned, to invite comments and suggestions, and, especially, to encourage participation. We believe that this facility will be an important step toward establishing the scientific and technical basis for a National High Intensity Facility. This can be achieved through active participation by members of the radioactive beam (RB) community in (1) experiments with high quality radioactive beams of moderate intensity and, (2) R ampersand D on high beam-power targets and highly efficient ion sources. 5 refs., 4 figs

Status of the SLAC/LBL/LLNL B-Factory and the BaBar detector

International Nuclear Information System (INIS)

Oddone, P.

1994-08-01

The primary motivation of the Asymmetric B-Factory is the study of CP violation. The decay of B mesons and, in particular, the decay of neutral B mesons, offers the possibility of determining conclusively whether CP violation is part and parcel of the Standard Model with three generations of quarks and leptons. Alternatively, the authors may discover that CP violation lies outside the present framework. In this paper the authors briefly describe the physics reach of the SLAC/LBL/LLNL Asymmetric B-Factory, the progress on the machine design and construction, the progress on the detector design, and the schedule to complete both projects

Crisis Resource Management in the Delivery Room: Development of Behavioral Markers for Team Performance in Emergency Simulation

Directory of Open Access Journals (Sweden)

Fabrizio Bracco

2018-03-01

Full Text Available Human factors are the most relevant issues contributing to adverse events in obstetrics. Specific training of Crisis Resource Management (CRM skills (i.e., problem solving and team management, resource allocation, awareness of environment, and dynamic decision-making is now widespread and is often based on High Fidelity Simulation. In order to be used as a guideline in simulated scenarios, CRM skills need to be mapped to specific and observable behavioral markers. For this purpose, we developed a set of observable behaviors related to the main elements of CRM in the delivery room. The observational tool was then adopted in a two-days seminar on obstetric hemorrhage where teams working in obstetric wards of six Italian hospitals took part in simulations. The tool was used as a guide for the debriefing and as a peer-to-peer feedback. It was then rated for its usefulness in facilitating the reflection upon one’s own behavior, its ease of use, and its usefulness for the peer-to-peer feedback. The ratings were positive, with a median of 4 on a 5-point scale. The CRM observational tool has therefore been well-received and presents a promising level of inter-rater agreement. We believe the tool could have value in facilitating debriefing and in the peer-to-peer feedback.

eLearning resources to supplement postgraduate neurosurgery training.

Science.gov (United States)

Stienen, Martin N; Schaller, Karl; Cock, Hannah; Lisnic, Vitalie; Regli, Luca; Thomson, Simon

2017-02-01

In an increasingly complex and competitive professional environment, improving methods to educate neurosurgical residents is key to ensure high-quality patient care. Electronic (e)Learning resources promise interactive knowledge acquisition. We set out to give a comprehensive overview on available eLearning resources that aim to improve postgraduate neurosurgical training and review the available literature. A MEDLINE query was performed, using the search term "electronic AND learning AND neurosurgery". Only peer-reviewed English-language articles on the use of any means of eLearning to improve theoretical knowledge in postgraduate neurosurgical training were included. Reference lists were crosschecked for further relevant articles. Captured parameters were the year, country of origin, method of eLearning reported, and type of article, as well as its conclusion. eLearning resources were additionally searched for using Google. Of n = 301 identified articles by the MEDLINE search, n = 43 articles were analysed in detail. Applying defined criteria, n = 28 articles were excluded and n = 15 included. Most articles were generated within this decade, with groups from the USA, the UK and India having a leadership role. The majority of articles reviewed existing eLearning resources, others reported on the concept, development and use of generated eLearning resources. There was no article that scientifically assessed the effectiveness of eLearning resources (against traditional learning methods) in terms of efficacy or costs. Only one article reported on satisfaction rates with an eLearning tool. All authors of articles dealing with eLearning and the use of new media in neurosurgery uniformly agreed on its great potential and increasing future use, but most also highlighted some weaknesses and possible dangers. This review found only a few articles dealing with the modern aspects of eLearning as an adjunct to postgraduate neurosurgery training. Comprehensive

Implementating Information Technology in E-Human Resource Management

Directory of Open Access Journals (Sweden)

Cristina-Dana Popescu (Mitu

2016-01-01

More and more organizations have been replacing face-to-face human resource managementactivities with electronic human resource management, which is considered as one of the keyfactors that every organization needs to focus. Considering that human resource management isone of the necessary needs of today’s business, the goal of this article is to establish the importanceof human resource management (HRM, to examine recent research in e-HRM in order to evaluatethe cumulated evidence on the relationship between HRM and e-HRM and to outline the impact ofe-HRM on human resource. Many specialists underlined the fact that human resource requiresmore attention and careful management than any other resource of an organization. This paperalso deals with the influence of Internet and information technology on work and human resourcemanagement.

Emissions & Generation Resource Integrated Database (eGRID), eGRID2012

Data.gov (United States)

U.S. Environmental Protection Agency — The Emissions emissions rates; net generation; resource mix; and many other attributes. eGRID2012 Version 1.0 is the eighth edition of eGRID, which contains the...

Plasma production for the 50 MeV plasma lens experiment at LBL

International Nuclear Information System (INIS)

Leemans, W.; van der Geer, B.; de Loos, M.; Conde, M.; Govil, R.; Chattopadhyay, S.

1994-06-01

The Center for Beam Physics at LBL has constructed a Beam Test Facility (BTF) housing a 50 MeV electron beam transport line, which uses the linac injector from the Advanced Light Source, and a terawatt Ti:Al 2 O 3 laser system. The linac operates at 50 MeV and generates 15 ps long electron bunches containing a charge of up to 2 nC. The measured unnormalized beam emittance is 0.33 mm-mrad. These parameters allow for a comprehensive study of focusing of relativistic electron beams with plasma columns, in both the overdense and underdense regime (adiabatic and tapered lenses). A study of adiabatic and/or tapered lenses requires careful control of plasma density and scale lengths of the plasma. We present experimental results on the production of plasmas through resonant two-photon ionization, with parameters relevant to an upcoming plasma lens experiment

Achilles’ heel: from greek mythology to challenges in the routines of school avaliation in the resources rooms

Directory of Open Access Journals (Sweden)

Denise Meyrelles de Jesus

2012-11-01

Full Text Available Based on the study entitled “National Observatory for Special Education: Network Studies on Multifunctional Resource Rooms" (Mendes, 2010, this article aims at discussing the assessment processes that took place in these rooms for multifunctional resources. The Greek mythology metaphor “Achilles’ Heel” in the title above is justified by the vulnerability of assessment in the process of inclusion. The main strategy for gathering data in this study was the adoption of focus groups led by the researchers. We sought to understand the meaning of initial assessment in the routines of the teachers involved in this study. Based on data analysis, we verified that the initial assessment procedures strongly resemble medical records issued by clinical professionals. The specialist teacher, together with the regular teacher, is in charge of identifying only students’ initial “learning inability”. Specialist teachers are not aware of the fact that they are responsible for this assessment, including for school census purposes. The data point to an unclear view of assessment, with poor interaction between these identification processes and the intervention procedures. The data also show the poor interaction between the relevant public services, which makes the family responsible for obtaining the student’s report. The results point to the need of more significant investments to restructure schools, providing them with collective spaces for discussing such serious issues and allowing us to develop more inclusive pedagogical practices regarding students' assessment.

eLearning resources to supplement postgraduate neurosurgery training.

OpenAIRE

Stienen, MN; Schaller, K; Cock, H; Lisnic, V; Regli, L; Thomson, S

2017-01-01

BACKGROUND: In an increasingly complex and competitive professional environment, improving methods to educate neurosurgical residents is key to ensure high-quality patient care. Electronic (e)Learning resources promise interactive knowledge acquisition. We set out to give a comprehensive overview on available eLearning resources that aim to improve postgraduate neurosurgical training and review the available literature. MATERIAL AND METHODS: A MEDLINE query was performed, using the search ter...

An infrared free electron laser system for the proposed Chemical Dynamics Research Laboratory at LBL based on a 500 MHz superconducting linac

International Nuclear Information System (INIS)

Kim, K.J.; Byrns, R.; Chattopadhyay, S.; Donahue, R.; Edighoffer, J.; Gough, R.; Hoyer, E.; Leemans, W.; Staples, J.; Taylor, B.; Xie, M.

1992-09-01

We describe a new design of the Infrared Free Electron Laser (IRFEL) for the proposed Chemical Dynamics Research Laboratory (CDRL) at LBL. The design and choice of parameters are dictated by the unique requirements of the CDRL scientific program. The accelerator system is based on the 500 MHz superconducting cavity technology to achieve a wavelength stability of 10 -4

eHealth literacy and preferences for eHealth resources in parents of children with complex CHD.

Science.gov (United States)

Kasparian, Nadine A; Lieu, Nathan; Winlaw, David S; Cole, Andrew; Kirk, Edwin; Sholler, Gary F

2017-05-01

Introduction This study aimed to (a) examine eHealth literacy, beliefs, and behaviours in parents of children with complex CHD, and (b) identify parents' preferences for the content, format, features, and functions of eHealth resources for CHD. Materials and methods Families (n=198) of children born between 2008 and 2011 and diagnosed with CHD requiring surgery were mailed a survey assessing a range of variables including eHealth literacy, beliefs, and behaviours as well as preferences for the format, functions, features, and content of eHealth resources for CHD. A total of 132 parents (83 mothers, 49 fathers) completed the survey (response rate: 50%). Mothers (96%) were more likely to access eHealth resources than fathers (83%, χ2=6.74, p=0.009). Despite high eHealth resource use, eHealth literacy was relatively low, with results demonstrating considerable and widespread gaps in awareness of, access to, and communication about eHealth resources. Over 50% of parents reported that decisions regarding their child's healthcare were influenced, to some extent, by web-based resources. Barriers to doctor-patient communication about eHealth included limited consultation time and concern about doctors' disapproval. Participants demonstrated a strong desire for "eHealth prescriptions" from their child's healthcare team, and perceived a wide range of eHealth topics as highly important, including treatment-related complications as well as physical, cognitive, and emotional development in children with CHD. Discussion Results suggest a need for stronger, more proactive partnerships between clinicians, researchers, educators, technologists, and patients and families to bring about meaningful innovations in the development and implementation of eHealth interventions in paediatric cardiology.

The gap between medical faculty's perceptions and use of e-learning resources.

Science.gov (United States)

Kim, Kyong-Jee; Kang, Youngjoon; Kim, Giwoon

2017-01-01

e-Learning resources have become increasingly popular in medical education; however, there has been scant research on faculty perceptions and use of these resources. To investigate medical faculty's use of e-learning resources and to draw on practical implications for fostering their use of such resources. Approximately 500 full-time faculty members in 35 medical schools across the nation in South Korea were invited to participate in a 30-item questionnaire on their perceptions and use of e-learning resources in medical education. The questionnaires were distributed in both online and paper formats. Descriptive analysis and reliability analysis were conducted of the data. Eighty faculty members from 28 medical schools returned the questionnaires. Twenty-two percent of respondents were female and 78% were male, and their rank, disciplines, and years of teaching experience all varied. Participants had positive perceptions of e-learning resources in terms of usefulness for student learning and usability; still, only 39% of them incorporated those resources in their teaching. The most frequently selected reasons for not using e-learning resources in their teaching were 'lack of resources relevant to my lectures,' 'lack of time to use them during lectures,' and 'was not aware of their availability.' Our study indicates a gap between medical faculty's positive perceptions of e-learning resources and their low use of such resources. Our findings highlight the needs for further study of individual and institutional barriers to faculty adoption of e-learning resources to bridge this gap.

Emissions & Generation Resource Integrated Database (eGRID), eGRID2010

Data.gov (United States)

U.S. Environmental Protection Agency — The Emissions emissions rates; net generation; resource mix; and many other attributes. eGRID2010 contains the complete release of year 2007 data, as well as years...

The use of information technologies and communication assistive technology as applied in the construction of knowledge of students with visual disabilities who attend rooms multifunction resources

Directory of Open Access Journals (Sweden)

Raquel Rosan Christino Gitahy

2016-04-01

Full Text Available This research aimed to investigate the contribution brought by the use of information and communication technologies applied to assistive technology in the construction of knowledge of students with visual impairment who attended the multifunction capabilities room. Research subjects were two students with visual impairment in different school years attending the multifunctional room features two educational institutions. In addition to students, the research subjects were also the teachers of the respective multi-functional resources they attend and the teachers who attended the in mainstream education. To achieve the goal, initially, the theoretical framework and was later carried out the field study procedure through the interview collection was consulted. The results found that two educational institutions surveyed are still building their pedagogical regarding the use and appropriation of ICT when used in multifunctional resource room as assistive technology. It is of fundamental importance to teacher training for the appropriation of ICT especially in relation to work with assistive technology in educational environments. Therefore, that it develops skills and abilities that allow building pedagogical practices in congruence with these technologies.

18 CFR 1301.2 - Public reading rooms.

Science.gov (United States)

2010-04-01

... 18 Conservation of Power and Water Resources 2 2010-04-01 2010-04-01 false Public reading rooms. 1301.2 Section 1301.2 Conservation of Power and Water Resources TENNESSEE VALLEY AUTHORITY PROCEDURES... 400 W. Summit Hill Drive, Knoxville, Tennessee 37902-1499, and 1101 Market Street, Chattanooga...

Recent developments in high charge state heavy ion beams at the LBL 88-inch Cyclotron

International Nuclear Information System (INIS)

Gough, R.A.; Clark, D.J.; Glasgow, L.R.

1978-01-01

Recent advances in design and operation of the internal PIG sources at the LBL 88-Inch Cyclotron have led to the development of high charge state (0.4 16 O 8+ . Total external intensities of these beams range from 10 12 particles/s for 6 Li 3+ to 0.1 particles/s for 16 O 8+ . Techniques have been developed for routine tune-out of the low intensity beams. These include use of model beams and reliance on the large systematic data base of cyclotron parameters which has been developed over many years of operation. Techniques for delivery of these weak beams to the experimental target areas are presented. Source design and operation, including special problems associated with Li, Be, and B beams are discussed

Emission & Generation Resource Integrated Database (eGRID)

Data.gov (United States)

U.S. Environmental Protection Agency — The Emissions & Generation Resource Integrated Database (eGRID) is an integrated source of data on environmental characteristics of electric power generation....

Impact of e-resources on learning in biochemistry: first-year medical students' perceptions.

Science.gov (United States)

Varghese, Joe; Faith, Minnie; Jacob, Molly

2012-05-16

E-learning resources (e-resources) have been widely used to facilitate self-directed learning among medical students. The Department of Biochemistry at Christian Medical College (CMC), Vellore, India, has made available e-resources to first-year medical students to supplement conventional lecture-based teaching in the subject. This study was designed to assess students' perceptions of the impact of these e-resources on various aspects of their learning in biochemistry. Sixty first-year medical students were the subjects of this study. At the end of the one-year course in biochemistry, the students were administered a questionnaire that asked them to assess the impact of the e-resources on various aspects of their learning in biochemistry. Ninety-eight percent of students had used the e-resources provided to varying extents. Most of them found the e-resources provided useful and of a high quality. The majority of them used these resources to prepare for periodic formative and final summative assessments in the course. The use of these resources increased steadily as the academic year progressed. Students said that the extent to which they understood the subject (83%) and their ability to answer questions in assessments (86%) had improved as a result of using these resources. They also said that they found biochemistry interesting (73%) and felt motivated to study the subject (59%). We found that first-year medical students extensively used the e-resources in biochemistry that were provided. They perceived that these resources had made a positive impact on various aspects of their learning in biochemistry. We conclude that e-resources are a useful supplement to conventional lecture-based teaching in the medical curriculum.

The production of new particles and muon-electron events in e+-e- annihilation at SPEAR

International Nuclear Information System (INIS)

Richter, B.

1977-01-01

Work carried out by the SLAC/LBL magnetic detector group at the SPEAR e + e - storage ring of the Stanford Linear Accelerator Center is reviewed. After describing the apparatus used, work which has been carried out on the decay modes of the psi and psi particles, searches for other narrow resonances over the mass region accessible to SPEAR, investigations of the total hadronic cross sections, the wide 1 -- states and other new states, and the discovery of anomalous μ-e events in the SPEAR data, are discussed. (U.K.)

Impact of e-resources on learning in biochemistry: first-year medical students’ perceptions

Science.gov (United States)

2012-01-01

Background E-learning resources (e-resources) have been widely used to facilitate self-directed learning among medical students. The Department of Biochemistry at Christian Medical College (CMC), Vellore, India, has made available e-resources to first-year medical students to supplement conventional lecture-based teaching in the subject. This study was designed to assess students’ perceptions of the impact of these e-resources on various aspects of their learning in biochemistry. Methods Sixty first-year medical students were the subjects of this study. At the end of the one-year course in biochemistry, the students were administered a questionnaire that asked them to assess the impact of the e-resources on various aspects of their learning in biochemistry. Results Ninety-eight percent of students had used the e-resources provided to varying extents. Most of them found the e-resources provided useful and of a high quality. The majority of them used these resources to prepare for periodic formative and final summative assessments in the course. The use of these resources increased steadily as the academic year progressed. Students said that the extent to which they understood the subject (83%) and their ability to answer questions in assessments (86%) had improved as a result of using these resources. They also said that they found biochemistry interesting (73%) and felt motivated to study the subject (59%). Conclusions We found that first-year medical students extensively used the e-resources in biochemistry that were provided. They perceived that these resources had made a positive impact on various aspects of their learning in biochemistry. We conclude that e-resources are a useful supplement to conventional lecture-based teaching in the medical curriculum. PMID:22510159

PACS war room for global teleradiology

Science.gov (United States)

Chen, Doris T.; Ho, Bruce K. T.; Chao, Woodrew; Taira, Ricky K.; Kangarloo, Hooshang

1995-05-01

UCLA is beginning teleradiology projects in Latin America, Asian Pacific, and the U.S. The UCLA teleradiology system communicates with remote imaging centers through a T1 based WAN and satellite technology. A network management center, i.e., PACS war room, with graphical user interface allows the system manager to monitor and control different elements of the system through various levels of abstraction from one location. The network manager software can monitor the activities of both hardware and software devices in the remote imaging centers, LAN and WAN performance, telearchiving and teleaccess pattern. Telearchiving can be monitored by graphically indicating large image movements between jukeboxes and over LAN or WAN. Once the teleradiology system is configured, the image flow pattern in a teleradiology center is predictable. Manual intervention of these teleradiology system functions is easily done through menu control in the war room display. A centralized network management with the global view of a teleradiology system has been developed. It can give commands to the elements of the system to tune the system for efficient utilization of the system resources. These managerial functions scale with the teleradiology system which is expandable to include many more potential remote imaging centers.

eHCM: Resources Reduction & Demand Increase, cover the gap by a managerial approach powered by an IT solutions.

Science.gov (United States)

Buccioli, Matteo; Agnoletti, Vanni; Padovani, Emanuele; Perger, Peter

2014-01-01

The economic and financial crisis has also had an important impact on the healthcare sector. Available resources have decreased, while at the same time costs as well as demand for healthcare services are on the rise. This coalescing negative impact on availability of healthcare resources is exacerbated even further by a widespread ignorance of management accounting matters. Little knowledge about costs is a strong source of costs augmentation. Although it is broadly recognized that cost accounting has a positive impact on healthcare organizations, it is not widespread adopted. Hospitals are essential components in providing overall healthcare. Operating rooms are critical hospital units not only in patient safety terms but also in expenditure terms. Understanding OR procedures in the hospital provides important information about how health care resources are used. There have been several scientific studies on management accounting in healthcare environments and more than ever there is a need for innovation, particularly by connecting business administration research findings to modern IT tools. IT adoption constitutes one of the most important innovation fields within the healthcare sector, with beneficial effects on the decision making processes. The e-HCM (e-Healthcare Cost Management) project consists of a cost calculation model which is applicable to Business Intelligence. The cost calculation approach comprises elements from both traditional cost accounting and activity-based costing. Direct costs for all surgical procedures can be calculated through a seven step implementation process.

Requirements and design of a high stable infrared free electron laser at LBL

International Nuclear Information System (INIS)

Kim, K.J.; Berz, M.; Chattopadhyay, S.; Gough, R.; Kim, C.; Kung, A.H.; Xie, M.; Edighoffer, J.; Stein, W.

1990-06-01

An infrared free electron laser (IRFEL) is being designed for the Chemical Dynamics Research Laboratory (CDRL) at LBL. The FEL is based on a 50 MeV RF linac operating in synchronization to the Advanced Light Source (ALS), and will produce intense (100 μJ per micropulse), narrow bandwidth (narrower than 0.1%) radiation between 3 μ and 50 μ. In the design, we pay particular attention to the FEL stability issues and require that the fluctuations in electron beam energy and in timing be less than 0.05% and 0.1 ps, respectively. The FEL spectrum can then be stabilized to about 10 -3 , or if grating is used, to 10 -4 . We discuss various sources of fluctuations in the gun, the bunchers and the accelerator sections, as well as the feedback and feedforward schemes to reduce these fluctuations. The accelerator structure is chosen to be of the side coupled, standing wave type for easier control. The beam transport is made isochronous to avoid the coupling between the energy and the timing fluctuations. 9 refs., 2 figs

Dynamic response analysis of the LBL Advanced Light Source synchrotron radiation storage ring

International Nuclear Information System (INIS)

Leung, K.

1993-05-01

This paper presents the dynamic response analysis of the photon source synchrotron radiation storage ring excited by ground motion measured at the Lawrence Berkeley Laboratory advanced light source building site. The high spectral brilliance requirement the photon beams of the advanced light source storage ring specified displacement of the quadrupole focusing magnets in the order of 1 micron in vertical motion.There are 19 magnets supported by a 430-inch steel box beam girder. The girder and all magnets are supported by the kinematic mount system normally used in optical equipment. The kinematic mount called a six-strut magnet support system is now considered as an alternative system for supporting SSC magnets in the Super Collider. The effectively designed and effectively operated six-strut support system is now successfully operated for the Advanced Light Source (ALS) accelerator at the Lawrence Berkeley Laboratory. This paper will present the method of analysis and results of the dynamic motion study at the center of the magnets under the most critical excitation source as recorded at the LBL site

Transient Beam Dynamics in the LBL 2 MV Injector

International Nuclear Information System (INIS)

Henestroza, E; Grote, D

1999-01-01

A driver-scale injector for the Heavy Ion Fusion Accelerator project has been built at LBL. This machine has exceeded the design goals of high voltage (> 2 MV), high current (> 0.8 A of K + ) and low normalized emittance (< 1 π mm-mr). The injector consists of a 750 keV gun pre-injector followed by an electrostatic quadrupole accelerator (ESQ) which provides strong (alternating gradient) focusing for the space-charge dominated beam, and simultaneously accelerates the ions to 2 MeV. A matching section is being built to match the beam to the electrostatic accelerator ELISE. The gun preinjector, designed to hold up to 1 MV with minimal breakdown risks, consists of a hot aluminosilicate source with a large curved emitting surface surrounded by a thick ''extraction electrode''. During beam turn-on the voltage at the source is biased from a negative potential, enough to reverse the electric field on the emitting surface and avoid emission, to a positive potential to start extracting the beam; it stays constant for about 1 (micro)s, and is reversed to turn-off the emission. Since the Marx voltage applied on the accelerating quadrupoles and the main pre-injector gap is a long, constant pulse (several (micro)s), the transient behavior is dominated by the extraction pulser voltage time profile. The transient longitudinal dynamics of the beam in the injector was simulated by running the Particle in Cell codes GYMNOS and WARP3d in a time dependent mode. The generalization and its implementation in WAIW3d of a method proposed by Lampel and Tiefenback to eliminate transient oscillations in a one-dimensional planar diode will be presented

Low emittance 0.8A K+ ion source for the LBL Induction Linac System Experiment (ILSE)

International Nuclear Information System (INIS)

Eylon, S.; Henestroza, E.; Chupp, W.W.; Yu, S.

1993-05-01

A high current injector for heavy ion fusion presently under construction at Lawrence Berkeley Laboratory requires large sources of up to 17 an in diameter and total potassium ion current of 790 mA with a low normalized transverse emittance of less than 0.5 mm-mr. A 1 in. diameter hot alumina silicate (zeolite) source was fabricated and tested in the injector setup of SBTE, an existing facility at LBL. Initial measurements showed a maximum space charge limited ion current of 95 mA. The corresponding density of 19 mA/cm 2 was limited by the source diode optics and not be the source emission. The density required for the high current injector is 4 mA/cm 2 . The normalized emittance was measured to be 0.06 mm-mrad, corresponding to a transverse temperature of 0.2 eV. Non-destructive life tests showed that the source can be operated under continuous operating conditions of the high current injector for more than a month (twenty eight-hour days, with 1 μs long pulses at 1 Hz). D.C. destructive life tests showed that ∼30% of the total stored K can be ionized and extracted, allowing, in principle, for years of operation for the high current injector. Furthermore, we shall describe the extension of the fabricating technique to large diameter sources (up to 17 cm) and report on measured ion emission performance, measured surface temperature uniformity and heating power considerations

The use of TOUGH2 for the LBL/USGS 3-dimensional site-scale model of Yucca Mountain, Nevada

International Nuclear Information System (INIS)

Bodvarsson, G.; Chen, G.; Haukwa, C.; Kwicklis, E.

1995-01-01

The three-dimensional site-scale numerical model o the unsaturated zone at Yucca Mountain is under continuous development and calibration through a collaborative effort between Lawrence Berkeley Laboratory (LBL) and the United States Geological Survey (USGS). The site-scale model covers an area of about 30 km 2 and is bounded by major fault zones to the west (Solitario Canyon Fault), east (Bow Ridge Fault) and perhaps to the north by an unconfirmed fault (Yucca Wash Fault). The model consists of about 5,000 grid blocks (elements) with nearly 20,000 connections between them; the grid was designed to represent the most prevalent geological and hydro-geological features of the site including major faults, and layering and bedding of the hydro-geological units. Submodels are used to investigate specific hypotheses and their importance before incorporation into the three-dimensional site-scale model. The primary objectives of the three-dimensional site-scale model are to: (1) quantify moisture, gas and heat flows in the ambient conditions at Yucca Mountain, (2) help in guiding the site-characterization effort (primarily by USGS) in terms of additional data needs and to identify regions of the mountain where sufficient data have been collected, and (3) provide a reliable model of Yucca Mountain that is validated by repeated predictions of conditions in new boreboles and the ESF and has therefore the confidence of the public and scientific community. The computer code TOUGH2 developed by K. Pruess at LBL was used along with the three-dimensional site-scale model to generate these results. In this paper, we also describe the three-dimensional site-scale model emphasizing the numerical grid development, and then show some results in terms of moisture, gas and heat flow

Synergistic interaction between gold nanoparticles and nickel phthalocyanine in layer-by-layer (LbL) films: evidence of constitutional dynamic chemistry (CDC).

Science.gov (United States)

Alencar, Wagner S; Crespilho, Frank N; Martins, Marccus V A; Zucolotto, Valtencir; Oliveira, Osvaldo N; Silva, Welter C

2009-07-07

The concept of constitutional dynamic chemistry (CDC) based on the control of non-covalent interactions in supramolecular structures is promising for having a large impact on nanoscience and nanotechnology if adequate nanoscale manipulation methods are used. In this study, we demonstrate that the layer-by-layer (LbL) technique may be used to produce electroactive electrodes with ITO coated by tetrasulfonated nickel phthalocyanine (NiTsPc) alternated with poly(allylamine hydrochloride) (PAH) incorporating gold nanoparticles (AuNP), in which synergy has been achieved in the interaction between the nanoparticles and NiTsPc. The catalytic activity toward hydrogen peroxide (H(2)O(2)) in multilayer films was investigated using cyclic voltammetry, where oxidation of H(2)O(2) led to increased currents in the PAH-AuNP/NiTsPc films for the electrochemical processes associated with the phthalocyanine ring and nickel at 0.52 and 0.81 V vs. SCE, respectively, while for PAH/NiTsPc films (without AuNP) only the first redox process was affected. In control experiments we found out that the catalytic activity was not solely due to the presence of AuNP, but rather to the nanoparticles inducing NiTsPc supramolecular structures that favored access to their redox sites, thus yielding strong charge transfer. The combined effects of NiTsPc and AuNP, which could only be observed in nanostructured LbL films, point to another avenue to pursue within the CDC paradigm.

Mathematical models for indoor radon prediction

International Nuclear Information System (INIS)

Malanca, A.; Pessina, V.; Dallara, G.

1995-01-01

It is known that the indoor radon (Rn) concentration can be predicted by means of mathematical models. The simplest model relies on two variables only: the Rn source strength and the air exchange rate. In the Lawrence Berkeley Laboratory (LBL) model several environmental parameters are combined into a complex equation; besides, a correlation between the ventilation rate and the Rn entry rate from the soil is admitted. The measurements were carried out using activated carbon canisters. Seventy-five measurements of Rn concentrations were made inside two rooms placed on the second floor of a building block. One of the rooms had a single-glazed window whereas the other room had a double pane window. During three different experimental protocols, the mean Rn concentration was always higher into the room with a double-glazed window. That behavior can be accounted for by the simplest model. A further set of 450 Rn measurements was collected inside a ground-floor room with a grounding well in it. This trend maybe accounted for by the LBL model

A Well-Mixed Computational Model for Estimating Room Air Levels of Selected Constituents from E-Vapor Product Use

Directory of Open Access Journals (Sweden)

Ali A. Rostami

2016-08-01

Full Text Available Concerns have been raised in the literature for the potential of secondhand exposure from e-vapor product (EVP use. It would be difficult to experimentally determine the impact of various factors on secondhand exposure including, but not limited to, room characteristics (indoor space size, ventilation rate, device specifications (aerosol mass delivery, e-liquid composition, and use behavior (number of users and usage frequency. Therefore, a well-mixed computational model was developed to estimate the indoor levels of constituents from EVPs under a variety of conditions. The model is based on physical and thermodynamic interactions between aerosol, vapor, and air, similar to indoor air models referred to by the Environmental Protection Agency. The model results agree well with measured indoor air levels of nicotine from two sources: smoking machine-generated aerosol and aerosol exhaled from EVP use. Sensitivity analysis indicated that increasing air exchange rate reduces room air level of constituents, as more material is carried away. The effect of the amount of aerosol released into the space due to variability in exhalation was also evaluated. The model can estimate the room air level of constituents as a function of time, which may be used to assess the level of non-user exposure over time.

Catalog of Research Abstracts, 1993: Partnership opportunities at Lawrence Berkeley Laboratory

Energy Technology Data Exchange (ETDEWEB)

1993-09-01

The 1993 edition of Lawrence Berkeley Laboratory`s Catalog of Research Abstracts is a comprehensive listing of ongoing research projects in LBL`s ten research divisions. Lawrence Berkeley Laboratory (LBL) is a major multi-program national laboratory managed by the University of California for the US Department of Energy (DOE). LBL has more than 3000 employees, including over 1000 scientists and engineers. With an annual budget of approximately $250 million, LBL conducts a wide range of research activities, many that address the long-term needs of American industry and have the potential for a positive impact on US competitiveness. LBL actively seeks to share its expertise with the private sector to increase US competitiveness in world markets. LBL has transferable expertise in conservation and renewable energy, environmental remediation, materials sciences, computing sciences, and biotechnology, which includes fundamental genetic research and nuclear medicine. This catalog gives an excellent overview of LBL`s expertise, and is a good resource for those seeking partnerships with national laboratories. Such partnerships allow private enterprise access to the exceptional scientific and engineering capabilities of the federal laboratory systems. Such arrangements also leverage the research and development resources of the private partner. Most importantly, they are a means of accessing the cutting-edge technologies and innovations being discovered every day in our federal laboratories.

Some novel design features of the LBL metal vapor vacuum arc ion sources

International Nuclear Information System (INIS)

MacGill, R.A.; Brown, I.G.; Galvin, J.E.

1990-01-01

The family of MEVVA (metal vapor vacuum arc) high current metal ion sources developed at LBL over the past several years has grown to include a number of different source versions with a wide range of some of the design and operational parameters. The MicroMEVVA source is a particularly compact version, about 2 cm diam and 10 cm long, while the MEVVA IV weighs some 30 kG. MEVVAs IV and V incorporate multiple cathode assemblies (16 and 18 separate cathodes, respectively), and the operating cathode can be switched rapidly and without downtime. The new MEVVA V embodiment is quite compact considering its broad beam (10 cm), high voltage (100 kV), and multiple cathode features. The large-area extractor grids used in MEVVA V were fabricated using a particularly simple technique, and they are clamped into position and can thus be changed simply and quickly. The electrical system used to drive the arc is particularly simple and incorporates several attractive features. In this article we review and describe a number of the mechanical and electrical design features that have been developed for these sources

Fast rendering of scanned room geometries

DEFF Research Database (Denmark)

Olesen, Søren Krarup; Markovic, Milos; Hammershøi, Dorte

2014-01-01

Room acoustics are rendered in Virtual Realities based on models of the real world. These are typically rather coarse representations of the true geometry resulting in room impulse responses with a lack of natural detail. This problem can be overcome by using data scanned by sensors, such as e...

The Role of E-Vocabularies in the Description and Retrieval of Digital Educational Resources

Directory of Open Access Journals (Sweden)

Ana M. Fernández-Pampillón

2017-03-01

Full Text Available Vocabularies are linguistic resources that make it possible to access knowledge through words. They can constitute a mechanism to identify, describe, explore, and access all the digital resources with informational content pertaining to a specific knowledge domain. In this regard, they play a key role as systems for the representation and organization of knowledge in environments in which content is created and used in a collaborative and free manner, as is the case of social wikis and blogs on the Internet or educational content in e-learning environments. In e-learning environments, electronic vocabularies (e-vocabularies constitute a mechanism for conceptual representation of digital educational resources. They enable human and software agents either to locate and interpret resource content in large digital repositories, including the web, or to use them (vocabularies as an educational resource by itself to learn a discipline terminology. This review article describes what e-vocabularies are, what they are like, how they are used, how they work, and what they contribute to the retrieval of digital educational resources. The goal is to contribute to a clearer view of the concepts which we regard as crucial to understand e-vocabularies and their use in the field of e-learning to describe and retrieve digital educational resources.

Automation of information decision support to improve e-learning resources quality

Directory of Open Access Journals (Sweden)

A.L. Danchenko

2013-06-01

Full Text Available Purpose. In conditions of active development of e-learning the high quality of e-learning resources is very important. Providing the high quality of e-learning resources in situation with mass higher education and rapid obsolescence of information requires the automation of information decision support for improving the quality of e-learning resources by development of decision support system. Methodology. The problem is solved by methods of artificial intelligence. The knowledge base of information structure of decision support system that is based on frame model of knowledge representation and inference production rules are developed. Findings. According to the results of the analysis of life cycle processes and requirements to the e-learning resources quality the information model of the structure of the knowledge base of the decision support system, the inference rules for the automatically generating of recommendations and the software implementation are developed. Practical value. It is established that the basic requirements for quality are performance, validity, reliability and manufacturability. It is shown that the using of a software implementation of decision support system for researched courses gives a growth of the quality according to the complex quality criteria. The information structure of a knowledge base system to support decision-making and rules of inference can be used by methodologists and content developers of learning systems.

Adaptation of mathematical educational content in e-learning resources

Directory of Open Access Journals (Sweden)

Yuliya V. Vainshtein

2017-01-01

Full Text Available Modern trends in the world electronic educational system development determine the necessity of adaptive learning intellectual environments and resources’ development and implementation. An upcoming trend in improvement the quality of studying mathematical disciplines is the development and application of adaptive electronic educational resources. However, the development and application experience of adaptive technologies in higher education is currently extremely limited and does not imply the usage flexibility. Adaptive educational resources in the electronic environment are electronic educational resources that provide the student with a personal educational space, filled with educational content that “adapts” to the individual characteristics of the students and provides them with the necessary information.This article focuses on the mathematical educational content adaptation algorithms development and their implementation in the e-learning system. The peculiarity of the proposed algorithms is the possibility of their application and distribution for adaptive e-learning resources construction. The novelty of the proposed approach is the three-step content organization of the adaptive algorithms for the educational content: “introductory adaptation of content”, “the current adaptation of content”, “estimative and a corrective adaptation”. For each stage of the proposed system, mathematical algorithms for educational content adaptation in adaptive e-learning resources are presented.Due to the high level of abstraction and complexity perception of mathematical disciplines, educational content is represented in the various editions of presentation that correspond to the levels of assimilation of the course material. Adaptation consists in the selection of the optimal edition of the material that best matches the individual characteristics of the student. The introduction of a three-step content organization of the adaptive

Pupil Science Learning in Resource-Based e-Learning Environments

Science.gov (United States)

So, Wing-mui Winnie; Ching, Ngai-ying Fiona

2011-01-01

With the rapid expansion of broadband Internet connection and availability of high performance yet low priced computers, many countries around the world are advocating the adoption of e-learning, the use of computer technology to improve learning and teaching. The trend of e-learning has urged many teachers to incorporate online resources in their…

Requirements for Control Room Computer-Based Procedures for use in Hybrid Control Rooms

Energy Technology Data Exchange (ETDEWEB)

Le Blanc, Katya Lee [Idaho National Lab. (INL), Idaho Falls, ID (United States); Oxstrand, Johanna Helene [Idaho National Lab. (INL), Idaho Falls, ID (United States); Joe, Jeffrey Clark [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2015-05-01

Many plants in the U.S. are currently undergoing control room modernization. The main drivers for modernization are the aging and obsolescence of existing equipment, which typically results in a like-for-like replacement of analogue equipment with digital systems. However, the modernization efforts present an opportunity to employ advanced technology that would not only extend the life, but enhance the efficiency and cost competitiveness of nuclear power. Computer-based procedures (CBPs) are one example of near-term advanced technology that may provide enhanced efficiencies above and beyond like for like replacements of analog systems. Researchers in the LWRS program are investigating the benefits of advanced technologies such as CBPs, with the goal of assisting utilities in decision making during modernization projects. This report will describe the existing research on CBPs, discuss the unique issues related to using CBPs in hybrid control rooms (i.e., partially modernized analog control rooms), and define the requirements of CBPs for hybrid control rooms.

Room Airflows with Low Reynolds Number Effects

DEFF Research Database (Denmark)

Topp, Claus; Nielsen, Peter V.; Davidson, Lars

The behaviour of room airflows under fully turbulent conditions is well known both in terms of experiments and, numerical calculations by computational fluid dynamics (CFD). For room airflows where turbulence is not fully developed though, i.e. flows at low Reynolds numbers, the existing knowledge...... is limited. It has been the objective to investigate the behaviour of a plane isothermal wall jet in a full-scale ventilated room at low Reynolds numbers, i.e. when the flow is not fully turbulent. The results are significantly different from known theory for fully turbulent flows. It was found that the jet...... constants are a strong function of the Reynolds number up to a level of Reh≈500....

National conference on integrated resource planning: Proceedings

Energy Technology Data Exchange (ETDEWEB)

1991-12-31

Until recently, state regulators have focused most of their attention on the development of least-cost or integrated resource planning (IRP) processes for electric utilities. A number of commissions are beginning to scrutinize the planning processes of local gas distribution companies (LDCs) because of the increased control that LDCs have over their purchased gas costs (as well as the associated risks) and because of questions surrounding the role and potential of gas end-use efficiency options. Traditionally, resource planning (LDCs) has concentrated on options for purchasing and storing gas. Integrated resource planning involves the creation of a process in which supply-side and demand-side options are integrated to create a resource mix that reliably satisfies customers` short-term and long-term energy service needs at the lowest cost. As applied to gas utilities, an integrated resource plan seeks to balance cost and reliability, and should not be interpreted simply as the search for lowest commodity costs. The National Association of Regulatory Utility Commissioners` (NARUC) Energy Conservation committee asked Lawrence Berkeley Laboratory (LBL) to survey state PUCs to determine the extent to which they have undertaken least cost planning for gas utilities. The survey included the following topics: status of state PUC least-cost planning regulations and practices for gas utilities; type and scope of natural gas DSM programs in effect, including fuel substitution; economic tests and analysis methods used to evaluate DSM programs; relationship between prudency reviews of gas utility purchasing practices and integrated resource planning; key regulatory issued facing gas utilities during the next five years.

National conference on integrated resource planning: Proceedings

Energy Technology Data Exchange (ETDEWEB)

1991-01-01

Until recently, state regulators have focused most of their attention on the development of least-cost or integrated resource planning (IRP) processes for electric utilities. A number of commissions are beginning to scrutinize the planning processes of local gas distribution companies (LDCs) because of the increased control that LDCs have over their purchased gas costs (as well as the associated risks) and because of questions surrounding the role and potential of gas end-use efficiency options. Traditionally, resource planning (LDCs) has concentrated on options for purchasing and storing gas. Integrated resource planning involves the creation of a process in which supply-side and demand-side options are integrated to create a resource mix that reliably satisfies customers' short-term and long-term energy service needs at the lowest cost. As applied to gas utilities, an integrated resource plan seeks to balance cost and reliability, and should not be interpreted simply as the search for lowest commodity costs. The National Association of Regulatory Utility Commissioners' (NARUC) Energy Conservation committee asked Lawrence Berkeley Laboratory (LBL) to survey state PUCs to determine the extent to which they have undertaken least cost planning for gas utilities. The survey included the following topics: status of state PUC least-cost planning regulations and practices for gas utilities; type and scope of natural gas DSM programs in effect, including fuel substitution; economic tests and analysis methods used to evaluate DSM programs; relationship between prudency reviews of gas utility purchasing practices and integrated resource planning; key regulatory issued facing gas utilities during the next five years.

The use of public health e-learning resources by pharmacists in Wales: a quantitative evaluation.

Science.gov (United States)

Evans, Andrew; Evans, Sian; Roberts, Debra

2016-08-01

The aim of this study was to examine how communicable disease e-learning resources were utilised by pharmacy professionals and to identify whether uptake of the resources was influenced by disease outbreaks. Retrospective analysis of routine data regarding the number of individuals completing e-learning resources and statutory notifications of communicable disease. A high proportion of pharmacy professionals in Wales (38.8%, n = 915/2357) accessed the resources; around one in six completed multiple resources (n = 156). The most commonly accessed were those where there had been a disease outbreak during the study period. There was a strong positive correlation between e-learning uptake and number of disease cases; this was observed both for measles and scarlet fever. Communicable disease e-learning appears to be an acceptable method for providing communicable disease information to pharmacy professionals. Study findings suggest that e-learning uptake is positively influenced by disease outbreaks this reflects well both on pharmacy professionals and on the e-learning resources themselves. © 2016 Royal Pharmaceutical Society.

How do strategic decisions and operative practices affect operating room productivity?

Science.gov (United States)

Peltokorpi, Antti

2011-12-01

Surgical operating rooms are cost-intensive parts of health service production. Managing operating units efficiently is essential when hospitals and healthcare systems aim to maximize health outcomes with limited resources. Previous research about operating room management has focused on studying the effect of management practices and decisions on efficiency by utilizing mainly modeling approach or before-after analysis in single hospital case. The purpose of this research is to analyze the synergic effect of strategic decisions and operative management practices on operating room productivity and to use a multiple case study method enabling statistical hypothesis testing with empirical data. 11 hypotheses that propose connections between the use of strategic and operative practices and productivity were tested in a multi-hospital study that included 26 units. The results indicate that operative practices, such as personnel management, case scheduling and performance measurement, affect productivity more remarkably than do strategic decisions that relate to, e.g., units' size, scope or academic status. Units with different strategic positions should apply different operative practices: Focused hospital units benefit most from sophisticated case scheduling and parallel processing whereas central and ambulatory units should apply flexible working hours, incentives and multi-skilled personnel. Operating units should be more active in applying management practices which are adequate for their strategic orientation.

Global application of disorders of sex development-related electronic resources: e-learning, e-consultation and e-information sharing.

Science.gov (United States)

Muscarella, Miriam; Kranenburg-van Koppen, Laura; Grijpink-van den Biggelaar, Kalinka; Drop, Stenvert L S

2014-01-01

The past 20 years have seen proliferation of electronic (e) resources that promote improved understanding of disorders of sex development (DSD): e-learning for physicians and trainees, e-consultation between clinicians, and e-information for families and affected individuals. Recent e-learning advances have emerged from the European Society for Pediatric Endocrinology's online learning portal for current physicians and trainees. Developed with attention to developing clinical competencies incorporating learning theory, and presenting material that represents international best practice, this e-learning portal offers advances in training, making information more accessible for clinicians and trainees. Multiple levels of instruction, authentic case examples, collaborative forums for physicians and trainees, individualized feedback and user-friendly tools represent advances in trainee and physician learning that can take place in any location. e-consultation is an emerging tool that aims to connect physicians with specialists experienced in DSD care. Although it faces logistical challenges, e-consultation carries the potential to improve DSD care, especially in remote areas with limited access to DSD specialists. e-information for families and patients of all ages is widely accessible online, often with focus on DSD biology, medical care, and psychological and social support. e-information tools aid self-management and support of those affected by DSD. Efforts to improve these resources should aim to map information to individual users, incorporate optimally clear nomenclature, and continue as a 'shared enterprise' of clinicians, affected individuals, families and researchers. Improving the quality of DSD-related e-learning and e-information and developing e-consultation carries the potential to transform DSD care and support for patients, families and physicians worldwide. © 2014 S. Karger AG, Basel.

Evaluation of team skills for control room crews

International Nuclear Information System (INIS)

Gaddy, C.D.; Koontz, J.L.

1987-01-01

Although team training has received considerable attention throughout industry, a systematic approach to team skills training has only recently been proposed for control room crews. One important step of the approach to team skills training is evaluation of team skills. This paper describes methods and resources, and program considerations in team skills evaluation. The three areas pertaining to methods and resources are: development of evaluation criteria, preparation of event scenarios, and instructor training and additional resources. The program considerations include sequencing and coordination of team skills evaluation in the context of an overall operator training program

Can e-learning help you to connect compassionately? Commentary on a palliative care e-learning resource for India.

Science.gov (United States)

Datta, Soumitra Shankar; Agrawal, Sanjit

2017-01-01

e-learning resources need to be customised to the audience and learners to make them culturally relevant. The ' Palliative care e-learning resource for health care professionals in India' has been developed by the Karunashraya Hospice, Bengaluru in collaboration with the Cardiff Palliative Care Education Team, Wales to address the training needs of professionals in India. The resource, comprising over 20 modules, integrates psychological, social and medical care for patients requiring palliative care for cancer and other diseases. With increased internet usage, it would help in training a large number of professionals and volunteers in India who want to work in the field of palliative care.

Patient safety in the operating room: an intervention study on latent risk factors

Directory of Open Access Journals (Sweden)

van Beuzekom Martie

2012-06-01

Full Text Available Abstract Background Patient safety is one of the greatest challenges in healthcare. In the operating room errors are frequent and often consequential. This article describes an approach to a successful implementation of a patient safety program in the operating room, focussing on latent risk factors that influence patient safety. We performed an intervention to improve these latent risk factors (LRFs and increase awareness of patient safety issues amongst OR staff. Methods Latent risk factors were studied using a validated questionnaire applied to the OR staff before and after an intervention. A pre-test/post-test control group design with repeated measures was used to evaluate the effects of the interventions. The staff from one operating room of an university hospital acted as the intervention group. Controls consisted of the staff of the operating room in another university hospital. The outcomes were the changes in LRF scores, perceived incident rate, and changes in incident reports between pre- and post-intervention. Results Based on pre-test scores and participants’ key concerns about organizational factors affecting patient safety in their department the intervention focused on the following LRFs: Material Resources, Training and Staffing Recourses. After the intervention, the intervention operating room - compared to the control operating room - reported significantly fewer problems on Material Resources and Staffing Resources and a significantly lower score on perceived incident rate. The contribution of technical factors to incident causation decreased significantly in the intervention group after the intervention. Conclusion The change of state of latent risk factors can be measured using a patient safety questionnaire aimed at these factors. The change of the relevant risk factors (Material and Staffing resources concurred with a decrease in perceived and reported incident rates in the relevant categories. We conclude that

Layer-by-layer assembled biopolymer microcapsule with separate layer cavities generated by gas-liquid microfluidic approach.

Science.gov (United States)

Wang, Yifeng; Zhou, Jing; Guo, Xuecheng; Hu, Qian; Qin, Chaoran; Liu, Hui; Dong, Meng; Chen, Yanjun

2017-12-01

In this work, a layer-by-layer (LbL) assembled biopolymer microcapsule with separate layer cavities is generated by a novel and convenient gas-liquid microfluidic approach. This approach exhibits combined advantages of microfluidic approach and LbL assembly method, and it can straightforwardly build LbL-assembled capsules in mild aqueous environments at room temperature. In particular, using this approach we can build the polyelectrolyte multilayer capsule with favorable cavities in each layer, and without the need for organic solvent, emulsifying agent, or sacrificial template. Various components (e.g., drugs, proteins, fluorescent dyes, and nanoparticles) can be respectively encapsulated in the separate layer cavities of the LbL-assembled capsules. Moreover, the encapsulated capsules present the ability as colorimetric sensors, and they also exhibit the interesting release behavior. Therefore, the LbL-assembled biopolymer capsule is a promising candidate for biomedical applications in targeted delivery, controlled release, and bio-detection. Copyright © 2017 Elsevier B.V. All rights reserved.

The use of TOUGH2 for the LBL/USGS 3-dimensional site-scale model of Yucca Mountain, Nevada

Energy Technology Data Exchange (ETDEWEB)

Bodvarsson, G.; Chen, G.; Haukwa, C. [Lawrence Berkeley Laboratory, CA (United States)] [and others

1995-03-01

The three-dimensional site-scale numerical model of the unsaturated zone at Yucca Mountain is under continuous development and calibration through a collaborative effort between Lawrence Berkeley Laboratory (LBL) and the United States Geological Survey (USGS). The site-scale model covers an area of about 30 km{sup 2} and is bounded by major fault zones to the west (Solitario Canyon Fault), east (Bow Ridge Fault) and perhaps to the north by an unconfirmed fault (Yucca Wash Fault). The model consists of about 5,000 grid blocks (elements) with nearly 20,000 connections between them the grid was designed to represent the most prevalent geological and hydro-geological features of the site including major faults, and layering and bedding of the hydro-geological units. Further information about the three-dimensional site-scale model is given by Wittwer et al. and Bodvarsson et al.

Emissions & Generation Resource Integrated Database (eGRID), eGRID2002 (with years 1996 - 2000 data)

Data.gov (United States)

U.S. Environmental Protection Agency — The Emissions emissions rates; net generation; resource mix; and many other attributes. eGRID2002 (years 1996 through 2000 data) contains 16 Excel spreadsheets and...

Control room systems design for nuclear power plants

International Nuclear Information System (INIS)

1995-07-01

This publication provides a resource for those who are involved in researching, managing, conceptualizing, designing, manufacturing or backfitting power plant control room systems. It will also be useful to those responsible for performing reviews or evaluations of the design and facilities associated with existing power plant control room systems. The ultimate worth of the publication, however, will depend upon how well it can support its users. Readers are invited to provide comments and observations to the IAEA, Division of Nuclear Power. If appropriate, the report will subsequently be re-issued, taking such feedback into account. Refs, figs and tabs

Control room systems design for nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-07-01

This publication provides a resource for those who are involved in researching, managing, conceptualizing, designing, manufacturing or backfitting power plant control room systems. It will also be useful to those responsible for performing reviews or evaluations of the design and facilities associated with existing power plant control room systems. The ultimate worth of the publication, however, will depend upon how well it can support its users. Readers are invited to provide comments and observations to the IAEA, Division of Nuclear Power. If appropriate, the report will subsequently be re-issued, taking such feedback into account. Refs, figs and tabs.

"Boarding" Psychiatric Patients in Emergency Rooms: One Court Says "No More".

Science.gov (United States)

Appelbaum, Paul S

2015-07-01

"Boarding" involuntary psychiatric patients in medical emergency rooms is common in many parts of the United States. The practice, driven by a shortage of alternative resources, including limited inpatient capacity, can result in patients' being held for days without treatment or a hospital room, often in busy corridors or treatment rooms. A recent challenge to this practice led the Washington Supreme Court to declare it illegal and resulted in the appropriation of substantial funding to create new psychiatric beds. Centralized psychiatric crisis services, with appropriate payment models, may offer another approach to reducing the need for holding patients awaiting inpatient admission.

Tools for Scientist Engagement in E/PO: NASA SMD Community Workspace and Online Resources

Science.gov (United States)

Dalton, H.; Shipp, S. S.; Grier, J.; Gross, N. A.; Buxner, S.; Bartolone, L.; Peticolas, L. M.; Woroner, M.; Schwerin, T. G.

2014-12-01

The Science Mission Directorate (SMD) Science Education and Public Outreach (E/PO) Forums are here to help you get involved in E/PO! The Forums have been developing several online resources to support scientists who are - or who are interested in becoming - involved in E/PO. These include NASA Wavelength, EarthSpace, and the SMD E/PO online community workspace. NASA Wavelength is the one-stop shop of all peer-reviewed NASA education resources to find materials you - or your audiences - can use. Browse by audience (pre-K through 12, higher education, and informal education) or topic, or choose to search for something specific by keyword and audience. http://nasawavelength.org. EarthSpace, an online clearinghouse of Earth and space materials for use in the higher education classroom, is driven by a powerful search engine that allows you to browse the collection of resources by science topic, audience, type of material or key terms. All materials are peer-reviewed before posting, and because all submissions receive a digital object identifier (doi), submitted materials can be listed as publications. http://www.lpi.usra.edu/earthspace. The SMD E/PO online community workspace contains many resources for scientists. These include one-page guides on how to get involved, tips on how to make the most of your time spent on E/PO, and sample activities, as well as news on funding, policy, and what's happening in the E/PO community. The workspace also provides scientists and the public pathways to find opportunities for participation in E/PO, to learn about SMD E/PO projects and their impacts, to connect with SMD E/PO practitioners, and to explore resources to improve professional E/PO practice, including literature reviews, information about the Next Generation Science Standards, and best practices in evaluation and engaging diverse audiences. http://smdepo.org.

PAs and NPs in an emergency room-linked acute care clinic.

Science.gov (United States)

Currey, C J

1984-12-01

The use of hospital emergency rooms for nonurgent care during evenings hours often strains medical resources and may affect the quality of emergency care. One facility's effective use of an after-hours acute care clinic staffed by PAs and NPs to divert nonurgent problems away from its emergency room is outlined. PAs and NPs work during peak demand hours (evenings and weekends) under the supervision of an emergency room physician, and receive supplementary support from other emergency room personnel. Incoming patients are referred to the emergency room or acute care clinic, depending on the nature of their problems. Acute care clinic patients are then treated by the PA or NP and either released or referred to an emergency room physician, if their conditions warrant additional treatment. As a result, use of the acute care clinic has greatly reduced the amount of non-urgent medical treatment in the emergency room and has provided other advantages to both patients and staff as well. These advantages and the encouraging statistics following six months of the clinic's operation are discussed.

Antimutagenic and radioprotective properties of products from Lactobacterium Bulgaricum strains

International Nuclear Information System (INIS)

Rupova, I.; Benova, D.; Yagova, A.; Topalova, S.

1993-01-01

The antimutagenic properties of the strains LBL-4 and LBL-144 have been studied by the incidence of micronuclei in polychromatic erythrocytes (PE) and endogenous spleen colony forming units (E-CFU) in C57BL mice. The lyophilized lactic acid products have been administered orally in the course of 3 weeks on 5 consecutive days. After the last treatment the mice have been gamma irradiated with 0.5, 3.0, 7.0 and 8.0 Gy. The prophylactic pretreatment of mice with LBL-4 in the schedule 3 x 5 days has shown a reduction of the induced micronuclei in PE after gamma irradiation with 3.0 Gy (37% compared to 50.5%; p < 0.001). The radiation effects caused by a lower dose of 0.5 Gy has not been modified by LBL-4 (36.7% compared to 33.8%). The application of LBL-144 does not reduce the mutagenic activity of both 0.5 and 3.0 Gy gamma rays. Applied independently, both LBL-4 and LBL-144 have shown the same frequency of micro-nucleated PE as the male and female mice controls. The radioprotective properties of LBL-4 have been assessed according to E-CFU and the changes in spleen weights after irradiation with 7.0 and 8.0 Gy gamma rays. The amount of E-CFU have been counted on day 9 after irradiation. A significant increase of spleen colony formation units has been established in mice pretreated with LBL-4. The spleen weights of the protected mice have been increased compared to unprotected animals. The results obtained show a good protection of haemopoietic stem cells by the product LBL-4. (author)

Getting educated: e-learning resources in the design and execution of surgical trials.

Science.gov (United States)

Bains, Simrit

2009-01-01

An evidence-based approach to research, which includes important aspects such as critical appraisal, is essential for the effective conduct of clinical trials. Researchers who are interested in educating themselves about its principles in order to incorporate them into their trials face challenges when attempting to acquire this information from traditional learning sources. E-learning resources offer an intriguing possibility of overcoming the challenges posed by traditional learning, and show promise as a way to expand accessibility to quality education about evidence-based principles. An assessment of existing e-learning resources reveals positive educational avenues for researchers, although significant flaws exist. The Global EducatorTM by Global Research Solutions addresses many of these flaws and is an e-learning resource that combines convenience with comprehensiveness.

Environmental Health and Safety Hazards Experienced by Home Health Care Providers: A Room-by-Room Analysis.

Science.gov (United States)

Polivka, Barbara J; Wills, Celia E; Darragh, Amy; Lavender, Steven; Sommerich, Carolyn; Stredney, Donald

2015-11-01

The number of personnel providing in-home health care services is increasing substantially. The unique configuration of environmental hazards in individual client homes has a significant impact on the safety and health of home health care providers (HHPs). This mixed-methods study used data from a standardized questionnaire, focus groups, and individual interviews to explore environmental health and safety hazards encountered by HHPs in client homes. The participant sample (N = 68) included nurses, aides, therapists, and owners/managers from a variety of geographic locations. The most often-reported hazards were trip/slip/lift hazards, biohazards, and hazards from poor air quality, allergens, pests and rodents, and fire and burns. Frequency of identified key hazards varied by room, that is, kitchen (e.g., throw rugs, water on floor), bathroom (e.g., tight spaces for client handling), bedroom (e.g., bed too low), living room (e.g., animal waste), and hallway (e.g., clutter). Findings indicate the need for broader training to enable HHPs to identify and address hazards they encounter in client homes. © 2015 The Author(s).

Guidelines for control room design reviews

International Nuclear Information System (INIS)

1981-09-01

The control room design review is part of a broad program being undertaken by the nuclear industry and the government to ensure consideration of human factors in nuclear power plant design and operation. The purpose of the control room design review described by these guidelines is to (1) review and evaluate the control room workspace, instrumentation, controls, and other equipment from a human factors engineering point of view that takes into account both system demands and operator capabilities; and (2) to identify, assess, and implement control room design modifications that correct inadequate or unsuitable items. The scope of the control room design review described by these guidelines covers the human engineering review of completed control rooms; i.e., operational control rooms or those at that stage of the licensing process where control room design and equipment selection are committed. These guidelines should also be of use during the design process for new control rooms. However, additional analyses to optimize the allocation of functions to man and machine, and further examination of advanced control system technology, are recommended for new control rooms. Guidelines and references for comprehensive system analyses designed to incorporate human factors considerations into the design and development of new control rooms are presented in Appendix B. Where possible, a generic approach to the control room design review process is encouraged; for example, when control room designs are replicated wholly or in part in two or more units. Even when designs are not replicated exactly, generic reviews which can be modified to account for specific differences in particular control rooms should be considered. Industry organizations and owners groups are encouraged to coordinate joint efforts and share data to develop generic approaches to the design review process. The control room design review should accomplish the following specific objectives. To determine

Access and Use of E-Resources by the Lecturers and Students of ...

African Journals Online (AJOL)

This study examines the use and access of various e-resource databases in Modibbo Adama University of Technology, Yola. The study specifically highlights the preferences and importance of online resources among the lecturers and students of the School of Management and Information Technology of the university.

77 FR 62243 - Health Resources and Services Administration

Science.gov (United States)

2012-10-12

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Health Resources and Services Administration National... Services Administration (HRSA), Parklawn Building (and via audio conference call), 5600 Fishers Lane, Room... and Services Administration, Parklawn Building, Room 13-64, 5600 Fishers Lane, Rockville, Maryland...

Emergency control room design of a nuclear reactor used to produce radioisotope

Energy Technology Data Exchange (ETDEWEB)

Santos, Isaac J.A.L. dos; Farias, Larissa P. de; Ponte, Luana T.L.; Goncalves, Gabriel L.; Castro, Heraclito M.; Farias, Marcos S.; Carvalho, Paulo V.R. de; Vianna Filho, Alfredo M.V., E-mail: luquetti@ien.gov.br [Instituto Engenharia Nuclear (IEN/CNEN-RJ), Rio de Janeiro, RJ (Brazil). Departamento Engenharia Nuclear

2015-07-01

A control room is defined as a functional entity with an associated physical structure, where the operators carry out the centralized control, monitoring and administrative responsibilities. Emergency control room acts as an alternative control room for the purpose of shutting down or maintaining the facility in a safe shutdown state when the main control room is uninhabitable. The mission of emergency control room is to provide the resources to bring the plant to a safe shutdown condition after an evacuation of the main control room. An evacuation of the main control room is assumed when there is no possibility to accomplish tasks involved in the shutdown except reactor trip. The purpose of this paper is to present a specific approach for the design of the emergency control room of a nuclear reactor used to produce radioisotope. The approach is based on human factors standards and the participation of a multidisciplinary team in the development phase of the design. Using the information gathered from standards and from the multidisciplinary team a 3D Sketch and a 3D printing of the emergency control room were created. (author)

Emergency control room design of a nuclear reactor used to produce radioisotope

International Nuclear Information System (INIS)

Santos, Isaac J.A.L. dos; Farias, Larissa P. de; Ponte, Luana T.L.; Goncalves, Gabriel L.; Castro, Heraclito M.; Farias, Marcos S.; Carvalho, Paulo V.R. de; Vianna Filho, Alfredo M.V.

2015-01-01

A control room is defined as a functional entity with an associated physical structure, where the operators carry out the centralized control, monitoring and administrative responsibilities. Emergency control room acts as an alternative control room for the purpose of shutting down or maintaining the facility in a safe shutdown state when the main control room is uninhabitable. The mission of emergency control room is to provide the resources to bring the plant to a safe shutdown condition after an evacuation of the main control room. An evacuation of the main control room is assumed when there is no possibility to accomplish tasks involved in the shutdown except reactor trip. The purpose of this paper is to present a specific approach for the design of the emergency control room of a nuclear reactor used to produce radioisotope. The approach is based on human factors standards and the participation of a multidisciplinary team in the development phase of the design. Using the information gathered from standards and from the multidisciplinary team a 3D Sketch and a 3D printing of the emergency control room were created. (author)

A successive ionic layer adsorption and reaction (SILAR) method to fabricate a layer-by-layer (LbL) MnO2-reduced graphene oxide assembly for supercapacitor application

Science.gov (United States)

Jana, Milan; Saha, Sanjit; Samanta, Pranab; Murmu, Naresh Chandra; Kim, Nam Hoon; Kuila, Tapas; Lee, Joong Hee

2017-02-01

A facile, cost effective and additive-free successive ionic layer adsorption and reaction (SILAR) technique is demonstrated to develop layer-by-layer (LbL) assembly of reduced graphene oxide (RGO) and MnO2 (MnO2-RGOSILAR) on a stainless steel current collector, for designing light-weight and small size supercapacitor electrode. The transmission electron microscopy and field emission scanning electron microscopy images shows uniform distribution of RGO and MnO2 in the MnO2-RGOSILAR. The LbL (MnO2-RGOSILAR) demonstrates improved physical and electrochemical properties over the hydrothermally prepared MnO2-RGO (MnO2-RGOHydro). The electrochemical environment of MnO2-RGOSILAR is explained by constant phase element in the high frequency region, and a Warburg element in the low frequency region in the Z-View fitted Nyquist plot. The equivalent circuit of the MnO2-RGOHydro, displays the co-existence of EDL and constant phase element, indicating inhomogeneous distribution of MnO2 and RGO by the hydrothermal technique. An asymmetric supercapacitor device is designed with MnO2-RGOSILAR as positive electrode, and thermally reduced GO (TRGO) as negative electrode. The designed cell exhibits high energy density of ∼88 Wh kg-1, elevated power density of ∼23,200 W kg-1, and ∼79% retention in capacitance after 10,000 charge-discharge cycles.

Game theory: applications for surgeons and the operating room environment.

Science.gov (United States)

McFadden, David W; Tsai, Mitchell; Kadry, Bassam; Souba, Wiley W

2012-11-01

Game theory is an economic system of strategic behavior, often referred to as the "theory of social situations." Very little has been written in the medical literature about game theory or its applications, yet the practice of surgery and the operating room environment clearly involves multiple social situations with both cooperative and non-cooperative behaviors. A comprehensive review was performed of the medical literature on game theory and its medical applications. Definitive resources on the subject were also examined and applied to surgery and the operating room whenever possible. Applications of game theory and its proposed dilemmas abound in the practicing surgeon's world, especially in the operating room environment. The surgeon with a basic understanding of game theory principles is better prepared for understanding and navigating the complex Operating Room system and optimizing cooperative behaviors for the benefit all stakeholders. Copyright © 2012 Mosby, Inc. All rights reserved.

Impact of Operating Room Environment on Postoperative Central Nervous System Infection in a Resource-Limited Neurosurgical Center in South Asia.

Science.gov (United States)

Chidambaram, Swathi; Vasudevan, Madabushi Chakravarthy; Nair, Mani Nathan; Joyce, Cara; Germanwala, Anand V

2018-02-01

Postoperative central nervous system infections (PCNSIs) are serious complications following neurosurgical intervention. We previously investigated the incidence and causative pathogens of PCNSIs at a resource-limited, neurosurgical center in south Asia. This follow-up study was conducted to analyze differences in PCNSIs at the same institution following only one apparent change: the operating room air filtration system. This was a retrospective study of all neurosurgical cases performed between December 1, 2013, and March 31, 2016 at our center. Providers, patient demographic data, case types, perioperative care, rate of PCNSI, and rates of other complications were reviewed. These results were then compared with the findings of our previous study of neurosurgical cases between June 1, 2012, and June 30, 2013. All 623 neurosurgical operative cases over the study period were reviewed. Four patients (0.6%) had a PCNSI, and no patients had a positive cerebrospinal fluid (CSF) culture. In the previous study, among 363 cases, 71 patients (19.6%) had a PCNSI and 7 (1.9%) had a positive CSF culture (all Gram-negative organisms). The differences in both parameters are statistically significant (P system inside the neurosurgical operating rooms; this environmental change occurred during the 5 months between the 2 studies. This study demonstrates the impact of environmental factors in reducing infections. Copyright © 2017 Elsevier Inc. All rights reserved.

Control room philosophy: Principles of control room design and control room work

International Nuclear Information System (INIS)

Skriver, Jan; Ramberg, Jasmine; Allwin, Pernilla

2006-01-01

In order to provide insights for improvement of work in control rooms several factors have to be considered. Knowledge of principles including control room philosophies will guide the recommended improvements. In addition to knowledge about specific principles an advantage for an organization can be an understanding of similarities and policies used in other high risk industry. The report has been developed on the basis of a document analysis of international standards and other guiding documents. (NUREG 0711, ISO 11064, ISO 6385, IEC 60964). In addition to the document analysis which has strived to compare the documents to see similarities in important principals, experience from working with control room design, modifications and evaluations in other high risk industries has pervaded the report. Important principles have been identified which are recommended to be included in a control room philosophy. Many of these are similar to the principles identified in the international standards. An additional principal which is regarded as important is the utilization of Key Performance Indicators (KPI) which can be used as a measure to target preventative means. Further more it is critical that the control room philosophy is easy to access and comprehend for all users. One of the challenges that remain after having developed a control room philosophy is how to utilize it in the daily work situation. It is vital that the document remains as a living document, guiding the continual improvement of the control room in the various life cycle stages

Conhecimento sobre anticoagulantes orais e seu manejo por médicos de pronto atendimento Emergency-room doctors' knowledge about oral anticoagulants and its management

Directory of Open Access Journals (Sweden)

Larissa Periotto Borlina

2010-06-01

Full Text Available Contexto: Desde sua descoberta, os anticoagulantes orais (AO têm sido cada vez mais estudados e aplicados em diferentes doenças. No entanto, eles apresentam reações medicamentosas com fármacos que trazem riscos ao paciente. Objetivo: Identificar o nível de conhecimento dos médicos plantonistas de pronto atendimento sobre os AO e suas interações, medicamentosas ou não, e verificar se o médico frentista está preparado para integrar o conteúdo teórico com a rotina de urgências. Método: Aplicou-se um questionário a 100 médicos atuantes em pronto atendimentos de dois hospitais públicos e três privados em Curitiba. Visou-se saber se o médico frentista questiona ao paciente sobre o uso de AO. Também, avaliou-se o conhecimento do profissional e seu interesse em saber mais sobre: AO (quais deles conhecia; exames para controle; sinergismo com AO; e manejo das complicações. Resultados: Dos 100 entrevistados, 60% declararam perguntar ao paciente sobre o uso de AO, 81% tinham conhecimento insuficiente a respeito do sinergismo de algumas substâncias apresentadas e os AO, 15% desconheciam qual exame é utilizado para acompanhamento dos pacientes anticoagulados, 50,7% não sabiam os nomes comercias dos AO, 4% desconheciam seu antídoto, e 92% manifestaram interesse em melhorar seus conhecimentos sobre os AO. Conclusão: É BAIXo o número de médicos que atende em pronto atendimentos que conhece sobre os AO e que sabe manejar pacientes anticoagulados. É alta a porcentagem de médicos que não perguntam aos pacientes sobre o uso de AO e que desconhecem princípios do sinergismo medicamentoso, sendo que a maioria se interessou em melhorar seus conhecimentos sobre os anticoagulantes.Background: Since its discovery, oral anticoagulants (OA have been increasingly studied and used to treat different diseases. However, OA may cause adverse drug interactions that bring risks for patients. Objective: To identify the emergency room doctors

E-Library and Traditonal Library Resources Usage: A Comparative ...

African Journals Online (AJOL)

A comparative usage of e-library and traditional resources in Nigerian libraries was examined in this study. A descriptive survey method was adopted and a purposive sampling technique was used to select the sample and the process produced 125 academic, research, and public libraries in Nigeria. A total of 116 cases ...

Model of e-learning with electronic educational resources of new generation

Directory of Open Access Journals (Sweden)

A. V. Loban

2017-01-01

Full Text Available Purpose of the article: improving of scientific and methodical base of the theory of the е-learning of variability. Methods used: conceptual and logical modeling of the е-learning of variability process with electronic educational resource of new generation and system analysis of the interconnection of the studied subject area, methods, didactics approaches and information and communication technologies means. Results: the formalization complex model of the е-learning of variability with electronic educational resource of new generation is developed, conditionally decomposed into three basic components: the formalization model of the course in the form of the thesaurusclassifier (“Author of e-resource”, the model of learning as management (“Coordination. Consultation. Control”, the learning model with the thesaurus-classifier (“Student”. Model “Author of e-resource” allows the student to achieve completeness, high degree of didactic elaboration and structuring of the studied material in triples of variants: modules of education information, practical task and control tasks; the result of the student’s (author’s of e-resource activity is the thesaurus-classifier. Model of learning as management is based on the principle of personal orientation of learning in computer environment and determines the logic of interaction between the lecturer and the student when determining the triple of variants individually for each student; organization of a dialogue between the lecturer and the student for consulting purposes; personal control of the student’s success (report generation and iterative search for the concept of the class assignment in the thesaurus-classifier before acquiring the required level of training. Model “Student” makes it possible to concretize the learning tasks in relation to the personality of the student and to the training level achieved; the assumption of the lecturer about the level of training of a

Test Room Stability Plan

International Nuclear Information System (INIS)

1993-01-01

This plan documents the combination of designs, installations, programs, and activities that ensures that the underground excavations at the Waste Isolation Pilot Plant (WIPP), in which transuranic (TRU) waste may be emplaced during the Test Phase, will remain sufficiently stable and safe during that time. The current ground support systems installed at the WIPP are the result of over ten years of data collection from hundreds of geomechanical instruments and thousands of hours of direct observation of the changing conditions of the openings. In addition, some of the world's most respected experts on salt rock mechanics have provided input in the design process and concurrence on the suitability of the final design. The general mine rockbolt pattern and the ground support system for the test rooms are designed to specifically address the fracture and deformation geometries observed today at the WIPP. After an introductory chapter, this plan describes the general underground design, then proceeds to an account of general ground support performance, and finally focuses on the details of the special test room ground support systems. One such system already installed in Room 1, Panel 1, is described in comprehensive detail. Other test rooms in Panel 1, whether full-size or smaller, will be equipped with systems that ensure stability to the same or equivalent extent. They will benefit from the experience gained in the first test room, which in turn benefitted from the data and knowledge accumulated during previous stages (e.g., the Site and Preliminary Design Validation program) of the project

Planets in a Room

Science.gov (United States)

Giacomini, l.; Aloisi, F.; De Angelis, I.

2017-09-01

Teaching planetary science using a spherical projector to show the planets' surfaces is a very effective but usually very expensive idea. Whatsmore, it usually assumes the availability of a dedicated space and a trained user. "Planets in a room" is a prototypal low cost version of a small, spherical projector that teachers, museum, planetary scientists and other individuals can easily build and use on their own, to show and teach the planets The project of "Planets in a Room" was made by the italian non-profit association Speak Science with the collaboration of INAF-IAPS of Rome and the Roma Tre University (Dipartimento di Matematica e Fisica). This proposal was funded by the Europlanet Outreach Funding Scheme in 2016. "Planets in a room" will be presented during EPSC 2017 to give birth to the second phase of the project, when the outreach and research community will be involved and schools from all over Europe will be invited to participate with the aim of bringing planetary science to a larger audience.

Displacement Ventilation in a Room with Low-Level Diffusers

DEFF Research Database (Denmark)

Nielsen, Peter V.

Ventilation systems with vertical displacement flow have been used in industrial areas with high thermal loads for many years. Quite resently the vertical displacement flow systems have grown popular as comfort ventilation in rooms with thermal loads e.g. offices.......Ventilation systems with vertical displacement flow have been used in industrial areas with high thermal loads for many years. Quite resently the vertical displacement flow systems have grown popular as comfort ventilation in rooms with thermal loads e.g. offices....

Ambient Layer-by-Layer ZnO Assembly for Highly Efficient Polymer Bulk Heterojunction Solar Cells

KAUST Repository

Eita, Mohamed Samir; El Labban, Abdulrahman; Cruciani, Federico; Usman, Anwar; Beaujuge, Pierre; Mohammed, Omar F.

2015-01-01

The use of metal oxide interlayers in polymer solar cells has great potential because metal oxides are abundant, thermally stable, and can be used in fl exible devices. Here, a layer-by-layer (LbL) protocol is reported as a facile, room

Interfacial characterization and supercapacitive properties of polyaniline-Gum arabic nanocomposite/graphene oxide LbL modified electrodes

Science.gov (United States)

Oliveira, Rafaela D.; Santos, Cleverson S.; Ferreira, Rodolfo T.; Marciniuk, Gustavo; Marchesi, Luís F.; Garcia, Jarem R.; Vidotti, Marcio; Pessoa, Christiana A.

2017-12-01

In this manuscript, we describe the synthesis and electrochemical characterization of polyaniline-gum arabic nanocomposites and graphene oxide (PANI-GA/GO) modified electrodes with a detailed study concerning their supercapacitive properties. The electrode modification was carried out by using the Layer-by-Layer technique (LbL), where the PANI-GA nanocomposite dispersion was used as polycation and the GO colloidal dispersion as polyanion. The bilayer growth was followed by both UV-vis spectroscopy and cyclic voltammetry, and an increase in the characteristic PANI absorption and in the electrochemical signal was verified, confirming the electrode build up. Galvanostatic charge-discharge curves (GCDC) were performed to evaluate the supercapacitive properties of the modified electrodes, these results showed the dependence of the specific capacitance with the number of bilayers, where values of CS around 15 mF cm-2 (i = 0.1 mA cm-2) were found. Electrochemical impedance spectroscopy confirmed the pseudocapacitive properties of the modified electrodes, showing an increase in the low-frequency capacitance with the number of bilayers. Hereby the (PANI-GA/GO)-LbL electrodes were shown to be good candidates for active materials in supercapacitors.

Enterprise Resource Planning and E-Business

Directory of Open Access Journals (Sweden)

Doina FOTACHE

2006-01-01

Full Text Available It is inevitable that as enterprises grow or change to meet market demands and competitiv situations, new business requirements drive the expansion of IT resources in the computing environment. Successful business growth depends heavily on the ability to update, integrate, customize and deploy applications rapidly and provide fast, reliable, interactive data access to end users, from employees to suppliers, customers and partners. In the Internet age, businesses in all industries need to move from intra-company integration to inter-company integration in order to increase competitiveness. New enterprise applications rely on Internet infrastructure for e-business solutions and Web-based collaboration, so customers, employees, suppliers and business partners work together as if they were all one company.

Room for a rethink?

Energy Technology Data Exchange (ETDEWEB)

Walker, S. [Independent Editorial and Technical Services, Oxford (United Kingdom)

2000-05-01

Room-and-pillar has traditionally satisfied the need for a low-cost, flexible coal mining system. Its downside can be low resource recovery. With accessible reserves falling steadily, can mining companies afford to accept this? Simon Walker looks into this problem using evidence presented recently on the US experience by Richard Bonskorski of the US Energy Information Administration, Dr Michael Karmis of Virgina Tech, Roger O'Quinn from Eimco, an equipment manufacturer, and Larry Howe from J H Fletcher. An urgent need is identified to develop new systems to allow significant gains in extraction, using novel concepts such as remote mining. 2 refs., 1 fig., 4 photos.

An assessment of student experiences and learning based on a novel undergraduate e-learning resource.

Science.gov (United States)

Mehta, S; Clarke, F; Fleming, P S

2016-08-12

Purpose/objectives The aims of this study were to describe the development of a novel e-learning resource and to assess its impact on student learning experiences and orthodontic knowledge.Methods Thirty-two 4th year dental undergraduate students at Queen Mary University of London were randomly allocated to receive electronic access to e-learning material covering various undergraduate orthodontic topics over a 6-week period. Thirty-one control students were not given access during the study period. All students were asked to complete electronic quizzes both before (T0) and after (T1) the study period and a general questionnaire concerning familiarity with e-learning. The test group also completed a user satisfaction questionnaire at T1. Two focus groups were also undertaken to explore learners' experiences and suggestions in relation to the resource.Results The mean quiz result improved by 3.9% and 4.5% in the control and test groups, respectively. An independent t-test, however, demonstrated a lack of statistical significance in knowledge gain between control and test groups (P = 0.941). The qualitative feedback indicated that students believed that use of the resource enhanced knowledge and basic understanding with students expressing a wish to ingrain similar resources in other areas of undergraduate teaching.Conclusions Use of the novel orthodontic e-resource by 4th year undergraduate students over a 6-week period did not result in a significant improvement in subject knowledge. However, the e-learning has proven popular among undergraduates and the resources will continue to be refined.

30 CFR 71.402 - Minimum requirements for bathing facilities, change rooms, and sanitary flush toilet facilities.

Science.gov (United States)

2010-07-01

... nonirritating cleansing agent shall be provided for use at each shower. (2) Sanitary flush toilet facilities. (i..., change rooms, and sanitary flush toilet facilities. 71.402 Section 71.402 Mineral Resources MINE SAFETY... Rooms, and Sanitary Flush Toilet Facilities at Surface Coal Mines § 71.402 Minimum requirements for...

Room Acoustics

Science.gov (United States)

Kuttruff, Heinrich; Mommertz, Eckard

The traditional task of room acoustics is to create or formulate conditions which ensure the best possible propagation of sound in a room from a sound source to a listener. Thus, objects of room acoustics are in particular assembly halls of all kinds, such as auditoria and lecture halls, conference rooms, theaters, concert halls or churches. Already at this point, it has to be pointed out that these conditions essentially depend on the question if speech or music should be transmitted; in the first case, the criterion for transmission quality is good speech intelligibility, in the other case, however, the success of room-acoustical efforts depends on other factors that cannot be quantified that easily, not least it also depends on the hearing habits of the listeners. In any case, absolutely "good acoustics" of a room do not exist.

Community Relations Plan for Lawrence Berkeley Laboratory. Environmental Restoration Program

Energy Technology Data Exchange (ETDEWEB)

1993-07-01

The Lawrence Berkeley Laboratory (LBL) has applied to the California Environmental Protection Agency, Department of Toxic Substances Control (DTSC), for renewal of its Hazardous Waste Handling Facility Permit. A permit is required under Resource Conservation and Recovery Act (RCRA) regulations. The permit will allow LBL to continue using its current hazardous waste handling facility, upgrade the existing facility, and construct a replacement facility. The new facility is scheduled for completion in 1995. The existing facility will be closed under RCRA guidelines by 1996. As part of the permitting process, LBL is required to investigate areas of soil and groundwater contamination at its main site in the Berkeley Hills. The investigations are being conducted by LBL`s Environmental Restoration Program and are overseen by a number of regulatory agencies. The regulatory agencies working with LBL include the California Environmental Protection Agency`s Department of Toxic Substances Control, the California Regional Water Quality Control Board, the Bay Area Air Quality Management District, the East Bay Municipal Utilities District, and the Berkeley Department of Environmental Health. RCRA requires that the public be informed of LBL`s investigations and site cleanup, and that opportunities be available for the public to participate in making decisions about how LBL will address contamination issues. LBL has prepared this Community Relations Plan (CRP) to describe activities that LBL will use to keep the community informed of environmental restoration progress and to provide for an open dialogue with the public on issues of importance. The CRP documents the community`s current concerns about LBL`s Environmental Restoration Program. Interviews conducted between February and April 1993 with elected officials, agency staff, environmental organizations, businesses, site neighbors, and LBL employees form the basis for the information contained in this document.

e-MIR2: a public online inventory of medical informatics resources.

Science.gov (United States)

de la Calle, Guillermo; García-Remesal, Miguel; Nkumu-Mbomio, Nelida; Kulikowski, Casimir; Maojo, Victor

2012-08-02

Over the past years, the number of available informatics resources in medicine has grown exponentially. While specific inventories of such resources have already begun to be developed for Bioinformatics (BI), comparable inventories are as yet not available for the Medical Informatics (MI) field, so that locating and accessing them currently remains a difficult and time-consuming task. We have created a repository of MI resources from the scientific literature, providing free access to its contents through a web-based service. We define informatics resources as all those elements that constitute, serve to define or are used by informatics systems, ranging from architectures or development methodologies to terminologies, vocabularies, databases or tools. Relevant information describing the resources is automatically extracted from manuscripts published in top-ranked MI journals. We used a pattern matching approach to detect the resources' names and their main features. Detected resources are classified according to three different criteria: functionality, resource type and domain. To facilitate these tasks, we have built three different classification schemas by following a novel approach based on folksonomies and social tagging. We adopted the terminology most frequently used by MI researchers in their publications to create the concepts and hierarchical relationships belonging to the classification schemas. The classification algorithm identifies the categories associated with resources and annotates them accordingly. The database is then populated with this data after manual curation and validation. We have created an online repository of MI resources to assist researchers in locating and accessing the most suitable resources to perform specific tasks. The database contains 609 resources at the time of writing and is available at http://www.gib.fi.upm.es/eMIR2. We are continuing to expand the number of available resources by taking into account further

Awareness, Access and Usage of E-Journal Resources of the ...

African Journals Online (AJOL)

... information retrieval skills training to be embedded in the curriculum, undertaken at an appropriate time and supported by academic staff. Lecturers are to emphasize and popularize information technology and its usage by talking about it and giving assignment that will motivate students to use the E – journal resources.

Students' perception of E-Resources in an Academic Library: The ...

African Journals Online (AJOL)

This paper examines students' perception of e-resources in academic libraries: case study of the serial's section of 'Nimbe Adedipe Library, Federal University of Agriculture, Abeokuta, Ogun State, Nigeria. The survey research method was adopted for this study. A structured questionnaire was designed and used to collect ...

e-MIR2: a public online inventory of medical informatics resources

Directory of Open Access Journals (Sweden)

de la Calle Guillermo

2012-08-01

Full Text Available Abstract Background Over the past years, the number of available informatics resources in medicine has grown exponentially. While specific inventories of such resources have already begun to be developed for Bioinformatics (BI, comparable inventories are as yet not available for the Medical Informatics (MI field, so that locating and accessing them currently remains a difficult and time-consuming task. Description We have created a repository of MI resources from the scientific literature, providing free access to its contents through a web-based service. We define informatics resources as all those elements that constitute, serve to define or are used by informatics systems, ranging from architectures or development methodologies to terminologies, vocabularies, databases or tools. Relevant information describing the resources is automatically extracted from manuscripts published in top-ranked MI journals. We used a pattern matching approach to detect the resources’ names and their main features. Detected resources are classified according to three different criteria: functionality, resource type and domain. To facilitate these tasks, we have built three different classification schemas by following a novel approach based on folksonomies and social tagging. We adopted the terminology most frequently used by MI researchers in their publications to create the concepts and hierarchical relationships belonging to the classification schemas. The classification algorithm identifies the categories associated with resources and annotates them accordingly. The database is then populated with this data after manual curation and validation. Conclusions We have created an online repository of MI resources to assist researchers in locating and accessing the most suitable resources to perform specific tasks. The database contains 609 resources at the time of writing and is available at http://www.gib.fi.upm.es/eMIR2. We are continuing to expand the number

Occurrences in control room equipment, procedures and personnel performances: IRS control room events

International Nuclear Information System (INIS)

Tolstykh, V.

1994-01-01

The IAEA/NEA Incident Reporting System (IRS) was established in the early 1980, its objective being to gain from operating experience achieved in countries with nuclear power programmes by means of exchanging information on events relevant to safety. Among the 2171 events in the database, 175 events (i.e. 8%) were identified as ''control room events''. It was decided to group these into three sets for further study: 65 events with common mode/cause failures (CCFs), 22 events with cognitive errors and 30 events with unforeseen interaction between NPP systems. It is expected that the pitfalls experienced in the IRS and the questions derived from this study will help to gain a better understanding of the needs and interests of specialists in advanced information methods and artificial intelligence in NPP control rooms. (author)

Layer-by-Layer Enabled Nanomaterials for Chemical Sensing and Energy Conversion

Science.gov (United States)

Paterno, Leonardo G.; Soler, Maria A. G.

2013-06-01

The layer-by-layer (LbL) technique is a wet chemical method for the assembly of ultrathin films, with thicknesses up to 100 nm. This method is based on the successive transfer of molecular layers to a solid substrate that is dipped into cationic and anionic solutions in an alternating fashion. The adsorption is mainly driven by electrostatic interactions so that many molecular and nanomaterial systems can be engineered under this method. Moreover, it is inexpensive, can be easily performed, and does not demand sophisticated equipment or clean rooms. The most explored use of the LbL technique is to build up molecular devices for chemical sensing and energy conversion. Both applications require ultrathin films where specific elements must be organized with high control of thickness and spatial distribution, preferably in the nanolength and mesolength scales. In chemical sensors, the LbL technique is employed to assemble specific sensoactive materials such as conjugated polymers, enzymes, and immunological elements onto appropriated electrodes. Molecular recognition events are thus transduced by the assembled sensoactive layer. In energy-conversion devices, the LbL technique can be employed to fabricate different device's parts including electrodes, active layers, and auxiliary layers. In both applications, the devices' performance can be fully modulated and improved by simply varying film thickness and molecular architecture. The present review article highlights the main features of the LbL technique and provides a brief description of different (bio)chemical sensors, solar cells, and organic light-emitting diodes enabled by the LbL approach.

Preliminary performance of the LBL AECR

International Nuclear Information System (INIS)

Lyneis, C.M.; Xie, Zuqi; Clark, D.J.; Lam, R.S.; Lundgren, S.A.

1990-11-01

The AECR source, which operates at 14 GHz, is being developed for the 88-Inch Cyclotron at Lawrence Berkeley Laboratory. The AECR has been under source development since December 1989, when the mechanical construction was completed. The first AECR beams were injected into the cyclotron in June of 1990 and since then a variety of ion species from the AECR have been accelerated. The cyclotron recently accelerated 209 Bi 38+ to 954 MeV. An electron gun, which injects 10 to 150 eV electrons into the plasma chamber of the AECR, has been developed to increase the production of high charge state ions. With the electron gun the AECR has produced at 10 kV extraction voltage 131 eμA of O 7+ , 13 eμA of O 8+ , 17 eμA of Ar 14+ , 2.2 eμA of Kr 25+ , 1 eμA of Xe 31+ , and 0.2 eμA of Bi 38+ . The AECR was also tested as a single stage source with a coating of SiO 2 on the plasma chamber walls. This significantly improved its performance compared to no coating, but direct injection of electrons with the electron gun produced the best results. 5 refs., 6 figs., 4 tabs

Getting What We Paid for: a Script to Verify Full Access to E-Resources

Directory of Open Access Journals (Sweden)

Kristina M. Spurgin

2014-07-01

Full Text Available Libraries regularly pay for packages of e-resources containing hundreds to thousands of individual titles. Ideally, library patrons could access the full content of all titles in such packages. In reality, library staff and patrons inevitably stumble across inaccessible titles, but no library has the resources to manually verify full access to all titles, and basic URL checkers cannot check for access. This article describes the E-Resource Access Checker—a script that automates the verification of full access. With the Access Checker, library staff can identify all inaccessible titles in a package and bring these problems to content providers’ attention to ensure we get what we pay for.

Daylighting simulation: methods, algorithms, and resources

Energy Technology Data Exchange (ETDEWEB)

Carroll, William L.

1999-12-01

This document presents work conducted as part of Subtask C, ''Daylighting Design Tools'', Subgroup C2, ''New Daylight Algorithms'', of the IEA SHC Task 21 and the ECBCS Program Annex 29 ''Daylight in Buildings''. The search for and collection of daylighting analysis methods and algorithms led to two important observations. First, there is a wide range of needs for different types of methods to produce a complete analysis tool. These include: Geometry; Light modeling; Characterization of the natural illumination resource; Materials and components properties, representations; and Usability issues (interfaces, interoperability, representation of analysis results, etc). Second, very advantageously, there have been rapid advances in many basic methods in these areas, due to other forces. They are in part driven by: The commercial computer graphics community (commerce, entertainment); The lighting industry; Architectural rendering and visualization for projects; and Academia: Course materials, research. This has led to a very rich set of information resources that have direct applicability to the small daylighting analysis community. Furthermore, much of this information is in fact available online. Because much of the information about methods and algorithms is now online, an innovative reporting strategy was used: the core formats are electronic, and used to produce a printed form only secondarily. The electronic forms include both online WWW pages and a downloadable .PDF file with the same appearance and content. Both electronic forms include live primary and indirect links to actual information sources on the WWW. In most cases, little additional commentary is provided regarding the information links or citations that are provided. This in turn allows the report to be very concise. The links are expected speak for themselves. The report consists of only about 10+ pages, with about 100+ primary links, but

Analysis of room transfer function and reverberant signal statistics

DEFF Research Database (Denmark)

Georganti, Eleftheria; Mourjopoulos, John; Jacobsen, Finn

2008-01-01

For some time now, statistical analysis has been a valuable tool in analyzing room transfer functions (RTFs). This work examines existing statistical time-frequency models and techniques for RTF analysis (e.g., Schroeder's stochastic model and the standard deviation over frequency bands for the RTF...... magnitude and phase). RTF fractional octave smoothing, as with 1-slash 3 octave analysis, may lead to RTF simplifications that can be useful for several audio applications, like room compensation, room modeling, auralisation purposes. The aim of this work is to identify the relationship of optimal response...... and the corresponding ratio of the direct and reverberant signal. In addition, this work examines the statistical quantities for speech and audio signals prior to their reproduction within rooms and when recorded in rooms. Histograms and other statistical distributions are used to compare RTF minima of typical...

Three-dimensional point-cloud room model in room acoustics simulations

DEFF Research Database (Denmark)

Markovic, Milos; Olesen, Søren Krarup; Hammershøi, Dorte

2013-01-01

acquisition and its representation with a 3D point-cloud model, as well as utilization of such a model for the room acoustics simulations. A room is scanned with a commercially available input device (Kinect for Xbox360) in two different ways; the first one involves the device placed in the middle of the room...... and rotated around the vertical axis while for the second one the device is moved within the room. Benefits of both approaches were analyzed. The device's depth sensor provides a set of points in a three-dimensional coordinate system which represents scanned surfaces of the room interior. These data are used...... to build a 3D point-cloud model of the room. Several models are created to meet requirements of different room acoustics simulation algorithms: plane fitting and uniform voxel grid for geometric methods and triangulation mesh for the numerical methods. Advantages of the proposed method over the traditional...

Three-dimensional point-cloud room model for room acoustics simulations

DEFF Research Database (Denmark)

Markovic, Milos; Olesen, Søren Krarup; Hammershøi, Dorte

2013-01-01

acquisition and its representation with a 3D point-cloud model, as well as utilization of such a model for the room acoustics simulations. A room is scanned with a commercially available input device (Kinect for Xbox360) in two different ways; the first one involves the device placed in the middle of the room...... and rotated around the vertical axis while for the second one the device is moved within the room. Benefits of both approaches were analyzed. The device's depth sensor provides a set of points in a three-dimensional coordinate system which represents scanned surfaces of the room interior. These data are used...... to build a 3D point-cloud model of the room. Several models are created to meet requirements of different room acoustics simulation algorithms: plane fitting and uniform voxel grid for geometric methods and triangulation mesh for the numerical methods. Advantages of the proposed method over the traditional...

E-learning in medical education in resource constrained low- and middle-income countries.

Science.gov (United States)

Frehywot, Seble; Vovides, Yianna; Talib, Zohray; Mikhail, Nadia; Ross, Heather; Wohltjen, Hannah; Bedada, Selam; Korhumel, Kristine; Koumare, Abdel Karim; Scott, James

2013-02-04

In the face of severe faculty shortages in resource-constrained countries, medical schools look to e-learning for improved access to medical education. This paper summarizes the literature on e-learning in low- and middle-income countries (LMIC), and presents the spectrum of tools and strategies used. Researchers reviewed literature using terms related to e-learning and pre-service education of health professionals in LMIC. Search terms were connected using the Boolean Operators "AND" and "OR" to capture all relevant article suggestions. Using standard decision criteria, reviewers narrowed the article suggestions to a final 124 relevant articles. Of the relevant articles found, most referred to e-learning in Brazil (14 articles), India (14), Egypt (10) and South Africa (10). While e-learning has been used by a variety of health workers in LMICs, the majority (58%) reported on physician training, while 24% focused on nursing, pharmacy and dentistry training. Although reasons for investing in e-learning varied, expanded access to education was at the core of e-learning implementation which included providing supplementary tools to support faculty in their teaching, expanding the pool of faculty by connecting to partner and/or community teaching sites, and sharing of digital resources for use by students. E-learning in medical education takes many forms. Blended learning approaches were the most common methodology presented (49 articles) of which computer-assisted learning (CAL) comprised the majority (45 articles). Other approaches included simulations and the use of multimedia software (20 articles), web-based learning (14 articles), and eTutor/eMentor programs (3 articles). Of the 69 articles that evaluated the effectiveness of e-learning tools, 35 studies compared outcomes between e-learning and other approaches, while 34 studies qualitatively analyzed student and faculty attitudes toward e-learning modalities. E-learning in medical education is a means to an end

The keys to CERN conference rooms - Managing local collaboration facilities in large organisations

CERN Multimedia

Baron, T; Duran, G; Correia Fernandes, J; Ferreira, P; Gonzalez Lopez, J B; Jouberjean, F; Lavrut, L; Tarocco, N

2013-01-01

For a long time HEP has been ahead of the curve in its usage of remote collaboration tools, like videoconference and webcast, while the local CERN collaboration facilities were somewhat behind the expected quality standards for various reasons. This time is now over with the creation by the CERN IT department in 2012 of an integrated conference room service which provides guidance and installation services for new rooms (either equipped for video-conference or not), as well as maintenance and local support. Managing now nearly half of the 250 meeting rooms available on the CERN sites, this service has been built to cope with the management of all CERN rooms with limited human resources. This has been made possible by the intensive use of professional software to manage and monitor all the room equipment, maintenance and activity. This paper will focus on presenting these packages, either off-the-shelf commercial products (asset and maintenance management tool, remote audiovisual equipment monitoring systems, ...

Encapsulation of Multiple Microalgal Cells via a Combination of Biomimetic Mineralization and LbL Coating.

Science.gov (United States)

Kim, Minjeong; Choi, Myoung Gil; Ra, Ho Won; Park, Seung Bin; Kim, Yong-Joo; Lee, Kyubock

2018-02-13

The encapsulation of living cells is appealing for its various applications to cell-based sensors, bioreactors, biocatalysts, and bioenergy. In this work, we introduce the encapsulation of multiple microalgal cells in hollow polymer shells of rhombohedral shape by the following sequential processes: embedding of microalgae in CaCO₃ crystals; layer-by-layer (LbL) coating of polyelectrolytes; and removal of sacrificial crystals. The microcapsule size was controlled by the alteration of CaCO₃ crystal size, which is dependent on CaCl₂/Na₂CO₃ concentration. The microalgal cells could be embedded in CaCO₃ crystals by a two-step process: heterogeneous nucleation of crystal on the cell surface followed by cell embedment by the subsequent growth of crystal. The surfaces of the microalgal cells were highly favorable for the crystal growth of calcite; thus, micrometer-sized microalgae could be perfectly occluded in the calcite crystal without changing its rhombohedral shape. The surfaces of the microcapsules, moreover, could be decorated with gold nanoparticles, Fe₃O₄ magnetic nanoparticles, and carbon nanotubes (CNTs), by which we would expect the functionalities of a light-triggered release, magnetic separation, and enhanced mechanical and electrical strength, respectively. This approach, entailing the encapsulation of microalgae in semi-permeable and hollow polymer microcapsules, has the potential for application to microbial-cell immobilization for high-biomass-concentration cultivation as well as various other bioapplications.

Improving the safety of room air pneumoperitoneum for diagnostic laparoscopy.

Science.gov (United States)

Ikechebelu, J I; Okeke, C A F

2008-06-01

Laparoscopic examination is a useful investigation in the evaluation of infertile women. To perform this test, pneumoperitoneum is required to distend the abdomen, improve visibility and displace the intestines out of the pelvis. Several gases have been used to achieve this purpose including Nitrous Oxide (N2O), Carbondioxide (CO2), Helium, Xenon andAir. This was a prospective study in a private fertility centre in Nnewi, Nigeria aimed at reducing the morbidities inherent in the use Room Air pneumoperitoneum for diagnostic laparoscopy. This was sequel to an earlier study, which revealed that women who had Room Air pneumoperitoneum had a higher port wound infection rate, abdominal discomfort (feeling of retained gas in the abdomen) and shoulder pain with resultant delayed return to normal activity than women who had Co2 pneumoperitoneum. This study demonstrated that the use of soda lime to purify the Room Air and a low pressure suction pump to evacuate the air after the procedure significantly reduced the wound infection rate and virtually eliminated the abdominal discomfort and shoulder pain associated with Room Air pneumoperitoneum. This was followed by early return to normal activity. Therefore, use of Room Air for pneumoperitoneum is safe and affordable. It is recommended for low resource settings.

Intensity of delivery room resuscitation and neonatal outcomes in infants born at 33 to 36 weeks' gestation.

Science.gov (United States)

Jiang, S; Lyu, Y; Ye, X Y; Monterrosa, L; Shah, P S; Lee, S K

2016-02-01

Examine the relationship between delivery room resuscitation intensity and mortality, morbidities and resource use in late preterm infants. Retrospective cohort study of inborn infants born at 33 to 36 weeks' gestation and admitted to Canadian neonatal intensive care units during 2010 to 2013. The 13 619 infants were grouped according to delivery room resuscitation intensity: no or minimal resuscitation (64.5%); continuous positive airway pressure (10.2%); bag-mask ventilation (21.7%); endotracheal intubation (3.1%); and cardiopulmonary resuscitation (CPR) (0.6%). Overall mortality, early mortality, respiratory distress, pneumothorax, late-onset sepsis and resource use increased with higher intensity resuscitation. Compared with no or minimal resuscitation, intubation and CPR were associated with increased odds of mortality (adjusted odds ratio (95% confidence interval): 50 (20 to 125) and 180 (63 to 518), respectively). Intubation or higher intensity delivery room resuscitation is associated with increased mortality, morbidities and resource use in late preterm infants. Extra intensive care is required for such infants, especially during the first week of life.

Public census data on CD-ROM at Lawrence Berkeley Laboratory. Revision 1

Energy Technology Data Exchange (ETDEWEB)

Merrill, D.W.

1992-07-02

In connection with the Comprehensive Epidemiologic Data Resource (CEDR) and Populations at Risk to Environmental Pollution (PAREP) projects, of the Information and Computing Sciences Division (ICSD) at Lawrence Berkeley Laboratory (LBL), are using public socioeconomic and geographic data files which are available to CEDR and PAREP collaborators via LBL`s computing network. At this time 67 CD-ROM diskettes (approximately 35 gigabytes) are on line via the Unix file server cedrcd.lbl.gov. Most of the files are from the US Bureau of the Census, and most pertain to the 1990 Census of Population and Housing. This paper contains a list of the CD-ROMs available.

Public census data on CD-ROM at Lawrence Berkeley Laboratory

Energy Technology Data Exchange (ETDEWEB)

Merrill, D.W.

1992-07-02

In connection with the Comprehensive Epidemiologic Data Resource (CEDR) and Populations at Risk to Environmental Pollution (PAREP) projects, of the Information and Computing Sciences Division (ICSD) at Lawrence Berkeley Laboratory (LBL), are using public socioeconomic and geographic data files which are available to CEDR and PAREP collaborators via LBL's computing network. At this time 67 CD-ROM diskettes (approximately 35 gigabytes) are on line via the Unix file server cedrcd.lbl.gov. Most of the files are from the US Bureau of the Census, and most pertain to the 1990 Census of Population and Housing. This paper contains a list of the CD-ROMs available.

Wind pressure testing of tornado safe room components made from wood

Science.gov (United States)

Robert Falk; Deepak Shrestha

2016-01-01

To evaluate the ability of a wood tornado safe room to resist wind pressures produced by a tornado, two safe room com-ponents were tested for wind pressure strength. A tornado safe room ceiling panel and door were static-pressure-tested according to ASTM E 330 using a vacuum test system. Re-sults indicate that the panels had load capacities from 2.4 to 3.5 times that...

Permanent education in the vaccination room: what is the reality?

Science.gov (United States)

Martins, Jéssica Rauane Teixeira; Alexandre, Bruna Gabrielly Pereira; Oliveira, Valéria Conceição de; Viegas, Selma Maria da Fonseca

2018-01-01

To understand, from the perspective of the professional, the Permanent Education (PE) in the vaccination room in its real context. Multiple holistic-qualitative case studies, based on Maffesoli's Interpretive Sociology with 56 participants from four microregions of the Western Extended Region of Minas Gerais State. They present PE as infrequent and insufficient. They denote that the practical-theoretical experience with vaccine contributes to the work; the search for knowledge, starting from the professional itself; and the professional training fails to perform in the vaccination room. The notions of PE are linked to the daily needs of individuals and services, with indication of being interactive, periodic, in specific and non-global issues for better assimilation. Obstacles to the non-implementation of PEH are realized by the workload associated with insufficient human resources, the distance of the nurses from the vaccination room and the lack of support from the higher levels.

Energy Efficiency in Small Server Rooms: Field Surveys and Findings

Energy Technology Data Exchange (ETDEWEB)

Cheung, Iris [Hoi; Greenberg, Steve; Mahdavi, Roozbeh; Brown, Richard; Tschudi, William

2014-08-11

Fifty-seven percent of US servers are housed in server closets, server rooms, and localized data centers, in what are commonly referred to as small server rooms, which comprise 99percent of all server spaces in the US. While many mid-tier and enterprise-class data centers are owned by large corporations that consider energy efficiency a goal to minimize business operating costs, small server rooms typically are not similarly motivated. They are characterized by decentralized ownership and management and come in many configurations, which creates a unique set of efficiency challenges. To develop energy efficiency strategies for these spaces, we surveyed 30 small server rooms across eight institutions, and selected four of them for detailed assessments. The four rooms had Power Usage Effectiveness (PUE) values ranging from 1.5 to 2.1. Energy saving opportunities ranged from no- to low-cost measures such as raising cooling set points and better airflow management, to more involved but cost-effective measures including server consolidation and virtualization, and dedicated cooling with economizers. We found that inefficiencies mainly resulted from organizational rather than technical issues. Because of the inherent space and resource limitations, the most effective measure is to operate servers through energy-efficient cloud-based services or well-managed larger data centers, rather than server rooms. Backup power requirement, and IT and cooling efficiency should be evaluated to minimize energy waste in the server space. Utility programs are instrumental in raising awareness and spreading technical knowledge on server operation, and the implementation of energy efficiency measures in small server rooms.

Room with a View: Ethical Encounters in Room 13

Science.gov (United States)

Grube, Vicky

2012-01-01

In this article, the author describes ethical encounters in Room 13, a schoolroom where children made what they wanted, posed their own questions, and ran an art room like a small business. In Room 13 children had the responsibility to maintain all aspects of the art studio. Specific decisions fell to an annually elected management team, a small…

Reference framework for integrating web resources as e-learning services in .LRN

Directory of Open Access Journals (Sweden)

Fabinton Sotelo Gómez

2015-11-01

Full Text Available The learning management platforms (LMS as Dot LRN (.LRN have been widely disseminated and used as a teaching tool. However, despite its great potential, most of these platforms do not allow easy integration of common services on the Web. Integration of external resources in LMS is critical to extend the quantity and quality of educational services LMS. This article presents a set of criteria and architectural guidelines for the integration of Web resources for e-learning in the LRN platform. To this end, three steps are performed: first; the possible integration technologies to be used are described, second; the Web resources that provide educational services and can be integrated into LMS platforms are analyzed, finally; some architectural aspects of the relevant platform are identified for integration. The main contributions of this paper are: a characterization of Web resources and educational services available today on the Web; and the definition of criteria and guidelines for the integration of Web resources to .LRN.

Operating room management and operating room productivity: the case of Germany.

Science.gov (United States)

Berry, Maresi; Berry-Stölzle, Thomas; Schleppers, Alexander

2008-09-01

We examine operating room productivity on the example of hospitals in Germany with independent anesthesiology departments. Linked to anesthesiology group literature, we use the ln(Total Surgical Time/Total Anesthesiologists Salary) as a proxy for operating room productivity. We test the association between operating room productivity and different structural, organizational and management characteristics based on survey data from 87 hospitals. Our empirical analysis links improved operating room productivity to greater operating room capacity, appropriate scheduling behavior and management methods to realign interests. From this analysis, the enforcing jurisdiction and avoiding advance over-scheduling appear to be the implementable tools for improving operating room productivity.

Handbook of Research on E-Transformation and Human Resources Management Technologies: Organizational Outcomes and Challenges

NARCIS (Netherlands)

Bondarouk, Tatiana; Ruel, Hubertus Johannes Maria; Guiderdoni-Jourdain, Karine; Oiry, Ewan

2009-01-01

Digital advancements and discoveries are now challenging traditional human resource management services within businesses. The Handbook of Research on E-Transformation and Human Resources Management Technologies: Organizational Outcomes and Challenges provides practical, situated, and unique

Students' "Uses and Gratification Expectancy" Conceptual Framework in Relation to E-Learning Resources

Science.gov (United States)

Mondi, Makingu; Woods, Peter; Rafi, Ahmad

2007-01-01

This paper presents the systematic development of a "Uses and Gratification Expectancy" (UGE) conceptual framework which is able to predict students' "Perceived e-Learning Experience." It is argued that students' UGE as regards e-learning resources cannot be implicitly or explicitly explored without first examining underlying communication…

Usability Testing of a Multimedia e-Learning Resource for Electrolyte and Acid-Base Disorders

Science.gov (United States)

Davids, Mogamat Razeen; Chikte, Usuf; Grimmer-Somers, Karen; Halperin, Mitchell L.

2014-01-01

The usability of computer interfaces may have a major influence on learning. Design approaches that optimize usability are commonplace in the software development industry but are seldom used in the development of e-learning resources, especially in medical education. We conducted a usability evaluation of a multimedia resource for teaching…

E-learning in medical education in resource constrained low- and middle-income countries

Science.gov (United States)

2013-01-01

Background In the face of severe faculty shortages in resource-constrained countries, medical schools look to e-learning for improved access to medical education. This paper summarizes the literature on e-learning in low- and middle-income countries (LMIC), and presents the spectrum of tools and strategies used. Methods Researchers reviewed literature using terms related to e-learning and pre-service education of health professionals in LMIC. Search terms were connected using the Boolean Operators “AND” and “OR” to capture all relevant article suggestions. Using standard decision criteria, reviewers narrowed the article suggestions to a final 124 relevant articles. Results Of the relevant articles found, most referred to e-learning in Brazil (14 articles), India (14), Egypt (10) and South Africa (10). While e-learning has been used by a variety of health workers in LMICs, the majority (58%) reported on physician training, while 24% focused on nursing, pharmacy and dentistry training. Although reasons for investing in e-learning varied, expanded access to education was at the core of e-learning implementation which included providing supplementary tools to support faculty in their teaching, expanding the pool of faculty by connecting to partner and/or community teaching sites, and sharing of digital resources for use by students. E-learning in medical education takes many forms. Blended learning approaches were the most common methodology presented (49 articles) of which computer-assisted learning (CAL) comprised the majority (45 articles). Other approaches included simulations and the use of multimedia software (20 articles), web-based learning (14 articles), and eTutor/eMentor programs (3 articles). Of the 69 articles that evaluated the effectiveness of e-learning tools, 35 studies compared outcomes between e-learning and other approaches, while 34 studies qualitatively analyzed student and faculty attitudes toward e-learning modalities. Conclusions E

E-learning in medical education in resource constrained low- and middle-income countries

Directory of Open Access Journals (Sweden)

Frehywot Seble

2013-02-01

Full Text Available Abstract Background In the face of severe faculty shortages in resource-constrained countries, medical schools look to e-learning for improved access to medical education. This paper summarizes the literature on e-learning in low- and middle-income countries (LMIC, and presents the spectrum of tools and strategies used. Methods Researchers reviewed literature using terms related to e-learning and pre-service education of health professionals in LMIC. Search terms were connected using the Boolean Operators “AND” and “OR” to capture all relevant article suggestions. Using standard decision criteria, reviewers narrowed the article suggestions to a final 124 relevant articles. Results Of the relevant articles found, most referred to e-learning in Brazil (14 articles, India (14, Egypt (10 and South Africa (10. While e-learning has been used by a variety of health workers in LMICs, the majority (58% reported on physician training, while 24% focused on nursing, pharmacy and dentistry training. Although reasons for investing in e-learning varied, expanded access to education was at the core of e-learning implementation which included providing supplementary tools to support faculty in their teaching, expanding the pool of faculty by connecting to partner and/or community teaching sites, and sharing of digital resources for use by students. E-learning in medical education takes many forms. Blended learning approaches were the most common methodology presented (49 articles of which computer-assisted learning (CAL comprised the majority (45 articles. Other approaches included simulations and the use of multimedia software (20 articles, web-based learning (14 articles, and eTutor/eMentor programs (3 articles. Of the 69 articles that evaluated the effectiveness of e-learning tools, 35 studies compared outcomes between e-learning and other approaches, while 34 studies qualitatively analyzed student and faculty attitudes toward e-learning modalities

Delays in the operating room: signs of an imperfect system.

Science.gov (United States)

Wong, Janice; Khu, Kathleen Joy; Kaderali, Zul; Bernstein, Mark

2010-06-01

Delays in the operating room have a negative effect on its efficiency and the working environment. In this prospective study, we analyzed data on perioperative system delays. One neurosurgeon prospectively recorded all errors, including perioperative delays, for consecutive patients undergoing elective procedures from May 2000 to February 2009. We analyzed the prevalence, causes and impact of perioperative system delays that occurred in one neurosurgeon's practice. A total of 1531 elective surgical cases were performed during the study period. Delays were the most common type of error (33.6%), and more than half (51.4%) of all cases had at least 1 delay. The most common cause of delay was equipment failure. The first cases of the day and cranial cases had more delays than subsequent cases and spinal cases, respectively. A delay in starting the first case was associated with subsequent delays. Delays frequently occur in the operating room and have a major effect on patient flow and resource utilization. Thorough documentation of perioperative delays provides a basis for the development of solutions for improving operating room efficiency and illustrates the principles underlying the causes of operating room delays across surgical disciplines.

Permanent education in the vaccination room: what is the reality?

Directory of Open Access Journals (Sweden)

Jéssica Rauane Teixeira Martins

Full Text Available ABSTRACT Objective: To understand, from the perspective of the professional, the Permanent Education (PE in the vaccination room in its real context. Method: Multiple holistic-qualitative case studies, based on Maffesoli’s Interpretive Sociology with 56 participants from four microregions of the Western Extended Region of Minas Gerais State. Results: They present PE as infrequent and insufficient. They denote that the practical-theoretical experience with vaccine contributes to the work; the search for knowledge, starting from the professional itself; and the professional training fails to perform in the vaccination room. Final considerations: The notions of PE are linked to the daily needs of individuals and services, with indication of being interactive, periodic, in specific and non-global issues for better assimilation. Obstacles to the non-implementation of PEH are realized by the workload associated with insufficient human resources, the distance of the nurses from the vaccination room and the lack of support from the higher levels.

Control rooms and man-machine interface in nuclear power plants

International Nuclear Information System (INIS)

1990-08-01

The importance of man-machine interface for ensuring safe and reliable operation of nuclear power plants has always been recognized. Since the early 1970's, the concepts of operator support and human factors have been increasingly used to better define the role of control rooms. In the late 1970's, the lessons learned from experience considerably accelerated the development of recommendations and regulatory requirements governing the resources and data available to operators in nuclear power plant control rooms, and specified the expertise required to assist them in case of need. This document summarizes the steps which have been taken and are being planned around the world to improve the man-machine interface for safe and economic power generation. It intends to present to the reader useful examples on some selected control room design and man-machine interface practices for operation and surveillance of nuclear power plants. 53 refs, 94 figs, 27 tabs

Effect of improving the usability of an e-learning resource: a randomized trial.

Science.gov (United States)

Davids, Mogamat Razeen; Chikte, Usuf M E; Halperin, Mitchell L

2014-06-01

Optimizing the usability of e-learning materials is necessary to reduce extraneous cognitive load and maximize their potential educational impact. However, this is often neglected, especially when time and other resources are limited. We conducted a randomized trial to investigate whether a usability evaluation of our multimedia e-learning resource, followed by fixing of all problems identified, would translate into improvements in usability parameters and learning by medical residents. Two iterations of our e-learning resource [version 1 (V1) and version 2 (V2)] were compared. V1 was the first fully functional version and V2 was the revised version after all identified usability problems were addressed. Residents in internal medicine and anesthesiology were randomly assigned to one of the versions. Usability was evaluated by having participants complete a user satisfaction questionnaire and by recording and analyzing their interactions with the application. The effect on learning was assessed by questions designed to test the retention and transfer of knowledge. Participants reported high levels of satisfaction with both versions, with good ratings on the System Usability Scale and adjective rating scale. In contrast, analysis of video recordings revealed significant differences in the occurrence of serious usability problems between the two versions, in particular in the interactive HandsOn case with its treatment simulation, where there was a median of five serious problem instances (range: 0-50) recorded per participant for V1 and zero instances (range: 0-1) for V2 (P e-learning resource resulted in significant improvements in usability. This is likely to translate into improved motivation and willingness to engage with the learning material. In this population of relatively high-knowledge participants, learning scores were similar across the two versions. Copyright © 2014 The American Physiological Society.

Concentration Distribution in a Mixing Ventilated Room

DEFF Research Database (Denmark)

Jensen, Rasmus Lund; Pedersen, D.N.; Nielsen, Peter V.

2001-01-01

Today there is an increasing focus on the importance of a proper ventilation system to obtain good working conditions in the term of air and thermal quality to ensure high productivity. Different ventilation principles are used, e.g., mixing ventilation and displacement ventilation. In order...... that the air is fully mixed. The objective of this work is to determine the influence of the location of a pollutant, temperature differences and whether the room is furnished or not. It is also investigated if it is sufficient to determine the mean concentration in the room to determine the personal exposure....... Full scale experiments along with a breathing thermal manikin (BTM) have been used. The results show that the location of the sources is of great importance, just as well as temperature differences. Furthermore, the concentration in the breathing zone showed large differences throughout the room....

Synthesis of cadmium chalcogenide nanotubes at room temperature

KAUST Repository

Pan, Jun; Qian, Yitai

2012-01-01

Cadmium chalcogenide (CdE, E=S, Se, Te) polycrystalline nanotubes have been synthesized from precursor of CdS/cadmium thiolate complex at room temperature. The precursor was hydrothermally synthesized at 180 °C using thioglycolic acid (TGA) and cadmium acetate as starting materials. The transformation from the rod-like precursor of CdS/cadmium thiolate complex to CdS, CdSe and CdTe nanotubes were performed under constant stirring at room temperature in aqueous solution containing S 2-, Se 2- and Te 2-, respectively. The nanotube diameter can be controlled from 150 to 400 nm related to the dimension of templates. The XRD patterns show the cadmium chalcogenide nanotubes all corresponding to face-centered cubic structure. © 2012 Elsevier B.V. All rights reserved.

Synthesis of cadmium chalcogenide nanotubes at room temperature

KAUST Repository

Pan, Jun

2012-10-01

Cadmium chalcogenide (CdE, E=S, Se, Te) polycrystalline nanotubes have been synthesized from precursor of CdS/cadmium thiolate complex at room temperature. The precursor was hydrothermally synthesized at 180 °C using thioglycolic acid (TGA) and cadmium acetate as starting materials. The transformation from the rod-like precursor of CdS/cadmium thiolate complex to CdS, CdSe and CdTe nanotubes were performed under constant stirring at room temperature in aqueous solution containing S 2-, Se 2- and Te 2-, respectively. The nanotube diameter can be controlled from 150 to 400 nm related to the dimension of templates. The XRD patterns show the cadmium chalcogenide nanotubes all corresponding to face-centered cubic structure. © 2012 Elsevier B.V. All rights reserved.

Tritium Room Air Monitor Operating Experience Review

Energy Technology Data Exchange (ETDEWEB)

L. C. Cadwallader; B. J. Denny

2008-09-01

Monitoring the breathing air in tritium facility rooms for airborne tritium is a radiological safety requirement and a best practice for personnel safety. Besides audible alarms for room evacuation, these monitors often send signals for process shutdown, ventilation isolation, and cleanup system actuation to mitigate releases and prevent tritium spread to the environment. Therefore, these monitors are important not only to personnel safety but also to public safety and environmental protection. This paper presents an operating experience review of tritium monitor performance on demand during small (1 mCi to 1 Ci) operational releases, and intentional airborne inroom tritium release tests. The tritium tests provide monitor operation data to allow calculation of a statistical estimate for the reliability of monitors annunciating in actual tritium gas airborne release situations. The data show a failure to operate rate of 3.5E-06/monitor-hr with an upper bound of 4.7E-06, a failure to alarm on demand rate of 1.4E-02/demand with an upper bound of 4.4E-02, and a spurious alarm rate of 0.1 to 0.2/monitor-yr.

O muco traqueobrônquico humano mantido em temperatura ambiente e suas propriedades físico-químicas Physicochemical properties of human tracheobronchial sputum maintained at room temperature

Directory of Open Access Journals (Sweden)

Renata Claudia Zanchet

2007-02-01

Full Text Available OBJETIVO: Verificar a influência da permanência em temperatura ambiente na análise da transportabilidade por ação ciliar e por tosse e do ângulo de contato do muco traqueobrônquico. MÉTODOS: Foi coletado muco hialino de 30 indivíduos sem doença pulmonar, e purulento de vinte pacientes com bronquiectasia. As amostras foram analisadas logo após a coleta e novamente após 24 h. RESULTADOS: Para o muco purulento, após 24 h em temperatura ambiente, houve aumento no deslocamento por tosse (96 ± 50 vs. 118 ± 61 mm e diminuição do ângulo de contato (32 ± 6 vs. 27 ± 6 graus (p OBJECTIVE: To evaluate the effect that maintaining tracheobronchial sputum at room temperature has on the analysis of ciliary transport and cough, as well as on the contact angle. METHODS: Hyaline sputum was collected from 30 individuals without pulmonary diseases, and purulent sputum was collected from patients with bronchiectasis. The samples were analyzed immediately after collection and again after 24 h. RESULTS: After 24 h at room temperature, the purulent sputum presented an increase in cough-induced dislodgment (96 ± 50 vs. 118 ± 61 mm and a decrease in the contact angle (32 ± 6 vs. 27 ± 6 degrees (p < 0.05. For the hyaline sputum, there were no alterations in the parameters analyzed. CONCLUSION: Hyaline tracheobronchial sputum can be stored in room temperature for 24 h without presenting alterations in ciliary transport or contact angle. However, purulent sputum should not be stored at room temperature for many hours, since ciliary transport and contact angle might be altered as a result.

Hypoxia Room

Data.gov (United States)

Federal Laboratory Consortium — The Hypoxia Room is a 8x8x8 ft. clear vinyl plastic and aluminum frame construction enclosure located within USAREIM laboratory 028. The Hypoxia Room (manufactured...

Encapsulation of Multiple Microalgal Cells via a Combination of Biomimetic Mineralization and LbL Coating

Directory of Open Access Journals (Sweden)

Minjeong Kim

2018-02-01

Full Text Available The encapsulation of living cells is appealing for its various applications to cell-based sensors, bioreactors, biocatalysts, and bioenergy. In this work, we introduce the encapsulation of multiple microalgal cells in hollow polymer shells of rhombohedral shape by the following sequential processes: embedding of microalgae in CaCO3 crystals; layer-by-layer (LbL coating of polyelectrolytes; and removal of sacrificial crystals. The microcapsule size was controlled by the alteration of CaCO3 crystal size, which is dependent on CaCl2/Na2CO3 concentration. The microalgal cells could be embedded in CaCO3 crystals by a two-step process: heterogeneous nucleation of crystal on the cell surface followed by cell embedment by the subsequent growth of crystal. The surfaces of the microalgal cells were highly favorable for the crystal growth of calcite; thus, micrometer-sized microalgae could be perfectly occluded in the calcite crystal without changing its rhombohedral shape. The surfaces of the microcapsules, moreover, could be decorated with gold nanoparticles, Fe3O4 magnetic nanoparticles, and carbon nanotubes (CNTs, by which we would expect the functionalities of a light-triggered release, magnetic separation, and enhanced mechanical and electrical strength, respectively. This approach, entailing the encapsulation of microalgae in semi-permeable and hollow polymer microcapsules, has the potential for application to microbial-cell immobilization for high-biomass-concentration cultivation as well as various other bioapplications.

Physics, Computer Science and Mathematics Division. Annual report, 1 January--31 December 1977. [LBL, 1977

Energy Technology Data Exchange (ETDEWEB)

Lepore, J.V. (ed.)

1977-01-01

This annual report of the Physics, Computer Science and Mathematics Division describes the scientific research and other work carried out within the Division during 1977. The Division is concerned with work in experimental and theoretical physics, with computer science and applied mathematics, and with the operation of a computer center. The major physics research activity is in high-energy physics, although there is a relatively small program of medium-energy research. The High Energy Physics research program in the Physics Division is concerned with fundamental research which will enable man to comprehend the nature of the physical world. The major effort is now directed toward experiments with positron-electron colliding beam at PEP. The Medium Energy Physics program is concerned with research using mesons and nucleons to probe the properties of matter. This research is concerned with the study of nuclear structure, nuclear reactions, and the interactions between nuclei and electromagnetic radiation and mesons. The Computer Science and Applied Mathematics Department engages in research in a variety of computer science and mathematics disciplines. Work in computer science and applied mathematics includes construction of data bases, computer graphics, computational physics and data analysis, mathematical modeling, and mathematical analysis of differential and integral equations resulting from physical problems. The Computer Center provides large-scale computational support to LBL's scientific programs. Descriptions of the various activities are quite short; references to published results are given. 24 figures. (RWR)

Effect of Room Ventilation Rates in Rodent Rooms with Direct-Exhaust IVC Systems.

Science.gov (United States)

Geertsema, Roger S; Lindsell, Claire E

2015-09-01

When IVC are directly exhausted from a rodent housing room, the air quality of the room can become independent of the intracage air quality and may reduce the need for high room ventilation rates. This study assessed the effect of decreasing the ventilation rate in rodent rooms using direct-exhaust IVC systems. The study was conducted over 16 wk and compared conditions in 8 rodent rooms that had ventilation rates of 5 to 6 air changes per hour (ACH) with those in rooms at 10 to 12 ACH. At the low ventilation rate, rooms had higher CO₂ concentrations, higher dew point temperature, and lower particulate levels and spent a greater percentage of time above the temperature set point than did rooms at the high rate. The levels of allergens and endotoxins in room air were the same regardless of the ventilation rate. Differences seen in parameters within cages at the 2 ventilation rates were operationally irrelevant. We detected no total volatile organic compounds in the room that were attributable to ammonia, regardless of the ventilation rate. Clearing the air of ethanol after a spill took longer at the low compared with high rate. However, ethanol clearance was faster at the low rate when the demand-control system was activated than at the high ventilation rate alone. Air quality in the room and in the cages were acceptable with room ventilation rates of 5 to 6 ACH in rodent rooms that use direct-exhaust IVC systems.

Use of internet and E-Resources by Agricultural students in a ...

African Journals Online (AJOL)

The study examined the use of internet and e- resources by Agricultural students in a Nigerian university. The total population of students was 1, 200. The population sample for this study was 200 sets of questionnaire were administered to students between 200 and 500 leves in the departments of Agricultural Economics ...

A Personalised Information Support System for Searching Portals and E-Resources

Science.gov (United States)

Sirisha, B. S.; Jeevan, V. K. J.; Raja Kumar, R. V.; Goswami, A.

2009-01-01

Purpose: The purpose of this paper is to describe the development of a personalised information support system to help faculty members to search various portals and e-resources without typing the search terms in different interfaces and to obtain results re-ordered without human intervention. Design/methodology/approach: After a careful survey of…

Room temperature superconductors

International Nuclear Information System (INIS)

Sleight, A.W.

1995-01-01

If the Holy Grail of room temperature superconductivity could be achieved, the impact on could be enormous. However, a useful room temperature superconductor for most applications must possess a T c somewhat above room temperature and must be capable of sustaining superconductivity in the presence of magnetic fields while carrying a significant current load. The authors will return to the subject of just what characteristics one might seek for a compound to be a room temperature superconductor. 30 refs., 3 figs., 1 tab

Using PHP to Parse eBook Resources from Drupal 6 to Populate a Mobile Web Page

Directory of Open Access Journals (Sweden)

Junior Tidal

2012-10-01

Full Text Available The Ursula C. Schwerin library needed to create a page for its mobile website devoted to subscribed eBooks. These resources, however, were only available through the main desktop website. These resources were organized using the Drupal 6 content management system with contributed and core modules. It was necessary to create a solution to retrieve the eBook databases from the Drupal installation to a separate mobile site.

Room acoustics modeling using a point-cloud representation of the room geometry

DEFF Research Database (Denmark)

Markovic, Milos; Olesen, Søren Krarup; Hammershøi, Dorte

2013-01-01

Room acoustics modeling is usually based on the room geometry that is parametrically described prior to a sound transmission calculation. This is a highly room-specific task and rather time consuming if a complex geometry is to be described. Here, a run time generic method for an arbitrary room...... geometry acquisition is presented. The method exploits a depth sensor of the Kinect device that provides a point based information of a scanned room interior. After post-processing of the Kinect output data, a 3D point-cloud model of the room is obtained. Sound transmission between two selected points...... level of user immersion by a real time acoustical simulation of a dynamic scenes....

An Investigation into Saudi Students' Knowledge of and Attitudes towards E-Resources on BBC Learning English

Science.gov (United States)

Alzahrani, Khalid Saleh

2017-01-01

The BBC Learning English website has become an important method of learning and studying English as a second language, a resource that enhances the importance of e-learning. The aim of the current research is to find Saudi students' knowledge of and attitude towards e-resources on BBC Learning English. The sample size was 28 participants (17 male…

TUGAS ROOM ATTENDANT DALAM MENANGANI COMPLAINT TAMU DELUXE ROOM HOTEL HYAAT REGENCY BANDUNG

Directory of Open Access Journals (Sweden)

Reza Gustia Purnama

2016-05-01

Full Text Available Abstract - The problem is how meticulous the duties and responsibilities of the room attendant in the deluxe room Hotel Hyatt Regency Bandung, standard operational procedures in the deluxe room Hotel Hyatt Regency Bandung, and handling guest complaint in deluxe room Hotel Hyatt Regency Bandung. Author uses descriptive analysis, which is a form of writing in the actual situation describes strive about the object of research, then the data obtained in the form of a report compiled in. Based on the results of observation it can be concluded that the task and responsibility of the room attendant in the deluxe room Hyatt Regency Bandung already carry it out in accordance with standard operational procedures (SOP which is divided into two shifts, morning and evening shift which has a slightly different task, standard operational procedures in the deluxe room Hyatt Regency Bandung has been standard operating procedure in applying it at the hotel Hyatt Regency Bandung, and Guest complaint handling in deluxe room Hyatt Regency Bandung Hotel how to deal with and resolve the complaint vary slightly in view of the type of complaint. Based on the results of observation and discussion, the authors conclude that the Duty room attendant in handling customers compaint deluxe room in the Hyatt Regency Bandung Hotel when his handlers was conducted appropriately and propesional effects will be good for the image of the hyatt regency hotel bandung.   Keywords: Room Attendant, Complaint, Deluxe room   Abstraksi - Masalah yang di teliti adalah tugas dan tanggung jawab room attendant di deluxe room Hotel Hyatt Regency Bandung, standar operasional prosedur di deluxe room Hotel Hyatt Regency Bandung, dan penanganan complaint tamu di deluxe room Hotel Hyatt Regency Bandung.  Metode yang di gunakan menggunakan analisis deskriptif, yaitu bentuk penulisan yang di upayakan menggambarkan keadaan yang sebenarnya tetang objek penelitian,kemudian data yang di peroleh disusun

Electronic Human Resources Management (e-HRM Adoption Studies: Past and Future Research

Directory of Open Access Journals (Sweden)

Winarto Winarto

2018-05-01

Full Text Available Electronic human resource management (e-HRM systems become more widely used by profit and non-profit organization. However, the field currently lacks sound theoretical frameworks that can be useful in addressing a key issue concerning the implementation of e-HRM systems, in particular to obtain a better understanding of the factors influencing the adoption of e-HRM systems. The objective of this paper is to provide a foundation towards the development of a theoretical framework for the implementation of e-HRM systems and develop a conceptual model that would reflect the nature of e-HRM systems’ adoption through systematic literature review. Adopting Crossan and Apaydin’s procedure of systematic review, this paper investigated 21 empirical papers of electronics human resources management, then categorized them into 4 characteristics which influence the adoption; System and technology characteristics; Organizational characteristics; User/individual characteristics, and Environmental and contextual characteristics. Finally, the e-HRM adoption research framework is drawn and based on the framework; avenues for future research are discussed.   Bahasa Indonesia Abstrak: Manajemen sumber daya manusia elektronik (selanjutnya disebut dengan e-HRM semakin banyak digunakan oleh organisasi profit dan nonprofit. Namun, bidang dan topik ini belum memiliki kerangka teori yang mapan, yang dapat digunakan untuk menganalisis isu-isu terkait penerapan e-HRM, terutama mengenai faktor-faktor yang mempengaruhi adopsi sistem e-HRM. Tujuan penelitian ini adalah untuk memberikan landasan bagi pengembangan kerangka teoritis untuk implementasi sistem e-HRM dan mengembangkan model konseptual yang akan menggambarkan adopsi sistem e-HRM melalui tinjauan literatur sistematis. Mengadopsi prosedur dan metode Crossan dan Apaydin untuk melakukan telaah literatur secara sistematis, paper ini menyelidiki 21 publikasi empiris manajemen sumber daya manusia elektronik dari 2

E-evolution : e-commerce spread, bu e-dustrial revolution is on hold

International Nuclear Information System (INIS)

Lunan, D.

2001-01-01

Approximately two years ago, e-commerce seemed ready to revolutionize the way the oil and gas industry conducted business. After the dot-com demise, Statistics Canada reported that less than one per cent of resource sector companies were selling goods on the Internet. According to financial industry experts, the energy industry should implement an e-business strategy based on four major concepts. They recommended using the Internet as a procurement source, the idea easiest to implement and with the potential to positively improve the bottom line. The second area recommended was assets acquisition and disposition. Some portals have already targeted this market niche, such as IndigoPool.com, operated by Schlumberger. In addition to assets, the portal offers millions of kilometres of two-dimensional seismic data, as well as three-dimensional and gravity or magnetic surveys. Portals like IndigoPool also feature electronic data rooms, similar to physical data rooms where registered customers can view and analyze all relevant information. A key partner in IndigoPool is Waterhouse and Co., whose responsibility is the handling of bids for various properties in Western Canada. The third aspect recommended by Goldman Sachs in a report, is trading in a number of commodities like natural gas, crude oil and liquids, electricity, etc. The fourth aspect favored by Goldman Sachs is reporting and regulatory filings. The National Energy Board established a phased-in electronic regulatory filing environment in the spring of 2001. The standardization of industry and government information systems is continuing on an international scale. 5 figs

E-evolution : e-commerce spread, bu e-dustrial revolution is on hold

Energy Technology Data Exchange (ETDEWEB)

Lunan, D.

2001-09-03

Approximately two years ago, e-commerce seemed ready to revolutionize the way the oil and gas industry conducted business. After the dot-com demise, Statistics Canada reported that less than one per cent of resource sector companies were selling goods on the Internet. According to financial industry experts, the energy industry should implement an e-business strategy based on four major concepts. They recommended using the Internet as a procurement source, the idea easiest to implement and with the potential to positively improve the bottom line. The second area recommended was assets acquisition and disposition. Some portals have already targeted this market niche, such as IndigoPool.com, operated by Schlumberger. In addition to assets, the portal offers millions of kilometres of two-dimensional seismic data, as well as three-dimensional and gravity or magnetic surveys. Portals like IndigoPool also feature electronic data rooms, similar to physical data rooms where registered customers can view and analyze all relevant information. A key partner in IndigoPool is Waterhouse and Co., whose responsibility is the handling of bids for various properties in Western Canada. The third aspect recommended by Goldman Sachs in a report, is trading in a number of commodities like natural gas, crude oil and liquids, electricity, etc. The fourth aspect favored by Goldman Sachs is reporting and regulatory filings. The National Energy Board established a phased-in electronic regulatory filing environment in the spring of 2001. The standardization of industry and government information systems is continuing on an international scale. 5 figs.

28 CFR 16.2 - Public reading rooms.

Science.gov (United States)

2010-07-01

... 28 Judicial Administration 1 2010-07-01 2010-07-01 false Public reading rooms. 16.2 Section 16.2 Judicial Administration DEPARTMENT OF JUSTICE PRODUCTION OR DISCLOSURE OF MATERIAL OR INFORMATION... Relations Service—in Suite 2000, 600 E Street, NW., Washington, DC; (4) Drug Enforcement Administration—in...

ENERGY RESOURCES CENTER

Energy Technology Data Exchange (ETDEWEB)

Sternberg, Virginia

1979-11-01

First I will give a short history of this Center which has had three names and three moves (and one more in the offing) in three years. Then I will tell you about the accomplishments made in the past year. And last, I will discuss what has been learned and what is planned for the future. The Energy and Environment Information Center (EEIC), as it was first known, was organized in August 1975 in San Francisco as a cooperative venture by the Federal Energy Administration (FEA), Energy Research and Development Administration (ERDA) and the Environmental Protection Agency (EPA). These three agencies planned this effort to assist the public in obtaining information about energy and the environmental aspects of energy. The Public Affairs Offices of FEA, ERDA and EPA initiated the idea of the Center. One member from each agency worked at the Center, with assistance from the Lawrence Berkeley Laboratory Information Research Group (LBL IRG) and with on-site help from the EPA Library. The Center was set up in a corner of the EPA Library. FEA and ERDA each contributed one staff member on a rotating basis to cover the daily operation of the Center and money for books and periodicals. EPA contributed space, staff time for ordering, processing and indexing publications, and additional money for acquisitions. The LBL Information Research Group received funds from ERDA on a 189 FY 1976 research project to assist in the development of the Center as a model for future energy centers.

Use and Cost of Electronic Resources in Central Library of Ferdowsi University Based on E-metrics

Directory of Open Access Journals (Sweden)

Mohammad Reza Davarpanah

2012-07-01

Full Text Available The purpose of this study was to investigate the usage of electronic journals in Ferdowsi University, Iran based on e-metrics. The paper also aimed to emphasize the analysis of cost-benefit and the correlation between the journal impact factors and the usage data. In this study experiences of Ferdowsi University library on licensing and usage of electronic resources was evaluated by providing a cost-benefit analysis based on the cost and usage statistics of electronic resources. Vendor-provided data were also compared with local usage data. The usage data were collected by tracking web-based access locally, and by collecting vender-provided usage data. The data sources were one-year of vendor-supplied e-resource usage data such as Ebsco, Elsevier, Proquest, Emerald, Oxford and Springer and local usage data collected from the Ferdowsi university web server. The study found that actual usage values differ for vendor-provided data and local usage data. Elsevier has got the highest usage degree in searches, sessions and downloads. Statistics also showed that a small number of journals satisfy significant amount of use while the majority of journals were used less frequent and some were never used at all. The users preferred the PDF rather than HTML format. The data in subject profile suggested that the provided e-resources were best suited to certain subjects. There was no correlation between IF and electronic journal use. Monitoring the usage of e-resources gained increasing importance for acquisition policy and budget decisions. The article provided information about local metrics for the six surveyed vendors/publishers, e.g. usage trends, requests per package, cost per use as related to the scientific specialty of the university.

Improving operating room safety

Directory of Open Access Journals (Sweden)

Garrett Jill

2009-11-01

Full Text Available Abstract Despite the introduction of the Universal Protocol, patient safety in surgery remains a daily challenge in the operating room. This present study describes one community health system's efforts to improve operating room safety through human factors training and ultimately the development of a surgical checklist. Using a combination of formal training, local studies documenting operating room safety issues and peer to peer mentoring we were able to substantially change the culture of our operating room. Our efforts have prepared us for successfully implementing a standardized checklist to improve operating room safety throughout our entire system. Based on these findings we recommend a multimodal approach to improving operating room safety.

Control room philosophy: Principles of control room design and control room work; Kontrollrumsfilosofi: Principer foer kontrollrumsutformning och kontrollrumsarbete

Energy Technology Data Exchange (ETDEWEB)

Skriver, Jan; Ramberg, Jasmine; Allwin, Pernilla [Scandpower Risk Management AB, Uppsala (Sweden)

2006-01-15

In order to provide insights for improvement of work in control rooms several factors have to be considered. Knowledge of principles including control room philosophies will guide the recommended improvements. In addition to knowledge about specific principles an advantage for an organization can be an understanding of similarities and policies used in other high risk industry. The report has been developed on the basis of a document analysis of international standards and other guiding documents. (NUREG 0711, ISO 11064, ISO 6385, IEC 60964). In addition to the document analysis which has strived to compare the documents to see similarities in important principals, experience from working with control room design, modifications and evaluations in other high risk industries has pervaded the report. Important principles have been identified which are recommended to be included in a control room philosophy. Many of these are similar to the principles identified in the international standards. An additional principal which is regarded as important is the utilization of Key Performance Indicators (KPI) which can be used as a measure to target preventative means. Further more it is critical that the control room philosophy is easy to access and comprehend for all users. One of the challenges that remain after having developed a control room philosophy is how to utilize it in the daily work situation. It is vital that the document remains as a living document, guiding the continual improvement of the control room in the various life cycle stages.

Reliability of estimating the room volume from a single room impulse response

OpenAIRE

Kuster, M.

2008-01-01

The methods investigated for the room volume estimation are based on geometrical acoustics, eigenmode, and diffuse field models and no data other than the room impulse response are available. The measurements include several receiver positions in a total of 12 rooms of vastly different sizes and acoustic characteristics. The limitations in identifying the pivotal specular reflections of the geometrical acoustics model in measured room impulse responses are examined both theoretically and expe...

A leadership framework to support the use of e-learning resources.

Science.gov (United States)

McCutcheon, Karen

2014-06-01

Recognition needs to be given to emerging postgraduate nursing students' status of 'consumer', and the challenge for nurse education is to remain relevant and competitive in a consumer-led market. An e-learning model has been suggested as a competitive and contemporary way forward for student consumers, but successful introduction of this requires leadership and strong organisational management systems. This article applies the NHS leadership framework to nurse education in relation to implementation of e-learning and describes and interprets each element for application in higher education settings. By applying a leadership framework that acknowledges the skills and abilities of staff and encourages the formation of collaborative partnerships in the wider university community, educators can begin to develop skills and confidence in teaching using e-learning resources.

Large-scale resource sharing at public funded organizations. e-Human "Grid" Ecology.

NARCIS (Netherlands)

T.A. Knoch (Tobias); V. Baumgärtner (Volkmar); K.E. Egger (Kurt)

2008-01-01

textabstractWith ever-new technologies emerging also the amount of information to be stored and processed is growing exponentially and is believed to be always at the limit. In contrast, however, huge resources are available in the IT sector alike e.g. the renewable energy sector, which are often

Large-scale resource sharing at public funded organizations. e-Human "Grid" Ecology.

NARCIS (Netherlands)

T.A. Knoch (Tobias); V. Baumgärtner (Volkmar); L.V. de Zeeuw (Luc); F.G. Grosveld (Frank); K.E. Egger (Kurt)

2009-01-01

textabstractWith ever-new technologies emerging also the amount of information to be stored and processed is growing exponentially and is believed to be always at the limit. In contrast, however, huge resources are available in the IT sector alike e.g. the renewable energy sector, which are often

76 FR 60934 - Proposal Review Panel for Human Resource Development; Notice of Meeting

Science.gov (United States)

2011-09-30

... NATIONAL SCIENCE FOUNDATION Proposal Review Panel for Human Resource Development; Notice of...; Proposal Review Panel Human Resource Development ( 1199). Date/Time: November 1, 2011; 5 p.m. to 10 p.m...: Part-Open. Contact Person: Kelly Mack, Division of Human Resource Development, Room 815, National...

A Study of Assessment of Library E-resource Metasearch System

Directory of Open Access Journals (Sweden)

Fan-Chuan Tseng

2008-12-01

Full Text Available As the emergent development of computer and network technology, digital library and information service has become an important approach for users to increase their academic as well as job performance due to the authorized, accurate, and reliable information. In the realm of information management, the exploration of factors influencing information system utilization and the evaluation of benefits are two critical issues. However, related studies focus more on the system functions and usually ignore the effects of individual cognition and social influence. In this study, we extend the IS success model with two additional factors－self-efficacy and subjective norm, trying to explore the potential influences on digital library usage, user satisfaction and performance.This research takes the Chang Jung Christian University library E-resources Metasearch system as the case study. A questionnaire was developed and finally got 160 useful student samples to test and verify the hypotheses. The research results confirmed that self-efficacy and subjective norm can significantly affect the usage of E-resource Metasearch System. Subsequently, the users feel satisfied with the system, and increase their academic performance. Finally, we provide discussion, implications and suggestions in two aspects – cooperating more with educational programs to increase users’ information literacy, and improving the customer-oriented system interface, functions, and services to enhance its quality. [Article content in Chinese

E-HRM: innovation or irritation? An exploration of web-based human resource management in large companies

NARCIS (Netherlands)

Ruel, Hubertus Johannes Maria; Bondarouk, Tatiana; Looise, Jan C.

2004-01-01

Human Resource Management (HRM of HR) executives are feeling pressured by the threat of a new development in recent years: Electronic Human Resource Management systems, also known as E-HRM. Consultants and other experts purport that this phenomenon will decrease the number of HRM employees, reduce

76 FR 60933 - Proposal Review Panel for Human Resource Development; Notice of Meeting

Science.gov (United States)

2011-09-30

... NATIONAL SCIENCE FOUNDATION Proposal Review Panel for Human Resource Development; Notice of..., Proposal Review Panel Human Resource Development ( 1199). Date/Time: October 17, 2011; 5 p.m. to 10 p.m... Meeting: Part-Open. Contact Person: Kelly Mack, Division of Human Resource Development, Room 815, National...

Simulation analysis of resource flexibility on healthcare processes.

Science.gov (United States)

Simwita, Yusta W; Helgheim, Berit I

2016-01-01

This paper uses discrete event simulation to explore the best resource flexibility scenario and examine the effect of implementing resource flexibility on different stages of patient treatment process. Specifically we investigate the effect of resource flexibility on patient waiting time and throughput in an orthopedic care process. We further seek to explore on how implementation of resource flexibility on patient treatment processes affects patient access to healthcare services. We focus on two resources, namely, orthopedic surgeon and operating room. The observational approach was used to collect process data. The developed model was validated by comparing the simulation output with actual patient data collected from the studied orthopedic care process. We developed different scenarios to identify the best resource flexibility scenario and explore the effect of resource flexibility on patient waiting time, throughput, and future changes in demand. The developed scenarios focused on creating flexibility on service capacity of this care process by altering the amount of additional human resource capacity at different stages of patient care process and extending the use of operating room capacity. The study found that resource flexibility can improve responsiveness to patient demand in the treatment process. Testing different scenarios showed that the introduction of resource flexibility reduces patient waiting time and improves throughput. The simulation results show that patient access to health services can be improved by implementing resource flexibility at different stages of the patient treatment process. This study contributes to the current health care literature by explaining how implementing resource flexibility at different stages of patient care processes can improve ability to respond to increasing patients demands. This study was limited to a single patient process; studies focusing on additional processes are recommended.

The keys to CERN conference rooms - Managing local collaboration facilities in large organisations

International Nuclear Information System (INIS)

Baron, T; Domaracky, M; Duran, G; Fernandes, J; Ferreira, P; Lopez, J B Gonzalez; Jouberjean, F; Lavrut, L; Tarocco, N

2014-01-01

For a long time HEP has been ahead of the curve in its usage of remote collaboration tools, like videoconference and webcast, while the local CERN collaboration facilities were somewhat behind the expected quality standards for various reasons. This time is now over with the creation by the CERN IT department in 2012 of an integrated conference room service which provides guidance and installation services for new rooms (either equipped for videoconference or not), as well as maintenance and local support. Managing now nearly half of the 246 meeting rooms available on the CERN sites, this service has been built to cope with the management of all CERN rooms with limited human resources. This has been made possible by the intensive use of professional software to manage and monitor all the room equipment, maintenance and activity. This paper focuses on presenting these packages, either off-the-shelf commercial products (asset and maintenance management tool, remote audio-visual equipment monitoring systems, local automation devices, new generation touch screen interfaces for interacting with the room) when available or locally developed integration and operational layers (generic audio-visual control and monitoring framework) and how they help overcoming the challenges presented by such a service. The aim is to minimise local human interventions while preserving the highest service quality and placing the end user back in the centre of this collaboration platform.

Towards a QoE-Driven Resource Control in LTE and LTE-A Networks

Directory of Open Access Journals (Sweden)

Gerardo Gómez

2013-01-01

Full Text Available We propose a novel architecture for providing quality of experience (QoE awareness to mobile operator networks. In particular, we describe a possible architecture for QoE-driven resource control for long-term evolution (LTE and LTE-advanced networks, including a selection of KPIs to be monitored in different network elements. We also provide a description and numerical results of the QoE evaluation process for different data services as well as potential use cases that would benefit from the rollout of the proposed framework.

Have it your way. A modular approach to custom compact control rooms

International Nuclear Information System (INIS)

Harmon, Daryl; Scarola, Ken

2003-01-01

) to integrate fully qualified HMI devices directly into individual normal operational consoles. This paper describes a modular approach to designing custom compact control rooms. In particular, it (1) describes the Westinghouse HMI building blocks for a compact control room, (2) describes the integration of standard, software-based HMI resources using the building block approach, (3) provides examples of compact control room configurations based on this approach that support new plant construction and existing plant modernizations and (4) discusses the advantages of this compact control room design approach. (author)

A work process and information flow description of control room operations

International Nuclear Information System (INIS)

Davey, E.; Matthews, G.

2007-01-01

The control room workplace is the location from which all plant operations are supervised and controlled on a shift-to-shift basis. The activities comprising plant operations are structured into a number of work processes, and information is the common currency that is used to convey work requirements, communicate business and operating decisions, specify work practice, and describe the ongoing plant and work status. This paper describes the motivation for and early experience with developing a work process and information flow model of CANDU control room operations, and discusses some of the insights developed from model examination that suggest ways in which changes in control centre work specification, organization of resources, or asset layout could be undertaken to achieve operational improvements. (author)

Thermalization of monoenergetic neutrons in a concrete room

Energy Technology Data Exchange (ETDEWEB)

Vega C, H.R.; Manzanares A, E.; Hernandez D, V.M.; Mercado, G.A. [UAZ, A.P. 336, 98000 Zacatecas (Mexico); Iniguez, M.P.; Martin M, A. [Universidad de Valladolid, (Spain)

2006-07-01

The thermalization of neutrons from monoenergetic neutron sources in a concrete room has been studied. During calibration of neutron detectors it is mandatory to make corrections due to neutron scattering produced by the room walls, therefore this factor must be known in advance. The scattered neutrons are thermalized and produce a neutron field that is directly proportional to source strength and inversely proportional to room total wall-surfaces, the proportional coefficient has been calculated for neutrons whose energy goes from 1 eV to 20 MeV. This coefficient was calculated using Monte Carlo methods for 150, 200 and 300 cm-radius spherical cavity, where monoenergetic neutrons were located at the center, along the spherical cavity radius neutron spectra were calculated at several source-to-detector distances inside the cavity. The obtained coefficient is almost three times larger than the factor normally utilized. (Author)

Information Foraging in Nuclear Power Plant Control Rooms

International Nuclear Information System (INIS)

Boring, R.L.

2011-01-01

nformation foraging theory articulates the role of the human as an 'informavore' that seeks information and follows optimal foraging strategies (i.e., the 'information scent') to find meaningful information. This paper briefly reviews the findings from information foraging theory outside the nuclear domain and then discusses the types of information foraging strategies operators employ for normal and off-normal operations in the control room. For example, operators may employ a predatory 'wolf' strategy of hunting for information in the face of a plant upset. However, during routine operations, the operators may employ a trapping 'spider' strategy of waiting for relevant indicators to appear. This delineation corresponds to information pull and push strategies, respectively. No studies have been conducted to determine explicitly the characteristics of a control room interface that is optimized for both push and pull information foraging strategies, nor has there been empirical work to validate operator performance when transitioning between push and pull strategies. This paper explores examples of control room operators as wolves vs. spiders and con- cludes by proposing a set of research questions to investigate information foraging in control room settings.

Information Foraging in Nuclear Power Plant Control Rooms

Energy Technology Data Exchange (ETDEWEB)

R.L. Boring

2011-09-01

nformation foraging theory articulates the role of the human as an 'informavore' that seeks information and follows optimal foraging strategies (i.e., the 'information scent') to find meaningful information. This paper briefly reviews the findings from information foraging theory outside the nuclear domain and then discusses the types of information foraging strategies operators employ for normal and off-normal operations in the control room. For example, operators may employ a predatory 'wolf' strategy of hunting for information in the face of a plant upset. However, during routine operations, the operators may employ a trapping 'spider' strategy of waiting for relevant indicators to appear. This delineation corresponds to information pull and push strategies, respectively. No studies have been conducted to determine explicitly the characteristics of a control room interface that is optimized for both push and pull information foraging strategies, nor has there been empirical work to validate operator performance when transitioning between push and pull strategies. This paper explores examples of control room operators as wolves vs. spiders and con- cludes by proposing a set of research questions to investigate information foraging in control room settings.

The e-book as a pedagogical resource

Directory of Open Access Journals (Sweden)

Åsa Forsberg

2013-12-01

Full Text Available This roundtable proposes to present and discuss a project about the e-book as a pedagogical resource. The project will run from Spring 2013 until December 2013 and is a collaboration project between Center for Educational Development (CED, Lund University, and Lund University Libraries (LUB. It will be part of a larger collaboration project involving the universities in Southern Sweden. New possibilities in the digital learning environments The importance of digital texts is growing. A rapidly increasing number of e-books are made available by publishers and the large majority of scientific journals are published in fulltext. There are many advantages with digital texts: • They are immediately available independently of time and space, in computers and mobile devices • They are searchable • Created in a correct format they are available also for people with reading difficulties • An e-book can be integrated with othjer meda, such as sound clips, video clips etc • They are relatively easy to revise and update Many teachers at Lund University produce study material for their courses, such as course packs, tutorials, instructions and other types of texts. This material is distributed to the students in either print or digital format. The digital formats are mainly pdf-files and word-files. It is important to give the teachers access also to more advanced tools for producing course literature in digital form. Most interesting are tools making it possible to integrate other media (i.e. video and sound clips with text. A toolbox for production of course material in digital form The project will explore the possibilities to facilitate the production of e-books at Lund University. It will consist of an inventory of the teachers' requirements and expectations, an inventory of the production process including pilot studies of e-book production and an inventory of the need for support and training for teachers producing e-books. It will result in

Future control room design (modernization of control room systems)

International Nuclear Information System (INIS)

Reischl, Ludwig; Freitag, Timo; Dergel, Rene

2009-01-01

In the frame of lifetime extension for nuclear power plants the modernization of the complete safety and operational control technology will be digitalized. It is also recommended to modernize the operator facilities, monitoring systems in the control room, the back-up shut-down center and the local control stations. The authors summarize the reasons for the modernization recommendations and discuss possible solutions for display-oriented control rooms. A concept for control room backfitting includes generic requirements, requirements of the local authorities, ergonomic principles information content and information density, and the design process. The backfitting strategy should include a cooperation with the operational personnel, The quality assurance and training via simulator needs sufficient timing during the implementation of the backfitting.

E-MSD: an integrated data resource for bioinformatics.

Science.gov (United States)

Velankar, S; McNeil, P; Mittard-Runte, V; Suarez, A; Barrell, D; Apweiler, R; Henrick, K

2005-01-01

The Macromolecular Structure Database (MSD) group (http://www.ebi.ac.uk/msd/) continues to enhance the quality and consistency of macromolecular structure data in the worldwide Protein Data Bank (wwPDB) and to work towards the integration of various bioinformatics data resources. One of the major obstacles to the improved integration of structural databases such as MSD and sequence databases like UniProt is the absence of up to date and well-maintained mapping between corresponding entries. We have worked closely with the UniProt group at the EBI to clean up the taxonomy and sequence cross-reference information in the MSD and UniProt databases. This information is vital for the reliable integration of the sequence family databases such as Pfam and Interpro with the structure-oriented databases of SCOP and CATH. This information has been made available to the eFamily group (http://www.efamily.org.uk/) and now forms the basis of the regular interchange of information between the member databases (MSD, UniProt, Pfam, Interpro, SCOP and CATH). This exchange of annotation information has enriched the structural information in the MSD database with annotation from wider sequence-oriented resources. This work was carried out under the 'Structure Integration with Function, Taxonomy and Sequences (SIFTS)' initiative (http://www.ebi.ac.uk/msd-srv/docs/sifts) in the MSD group.

Usability testing of two e-learning resources: methods to maximize potential for clinician use.

Science.gov (United States)

Menon, Anita; Korner-Bitensky, Nicol; Chignell, Mark; Straus, Sharon

2012-04-01

Rigorous usability testing of e-learn-ing resources is an important prerequisite to their wide-spread use among clinicians. This study demonstrates the application of an evidence-based approach to usability testing of two stroke-related e-learning resources (StrokEngine). 14 stroke rehabilitation clinicians (occupational therapists and physiotherapists) from Ontario, Canada participated in a 1.5 h in-person testing session. Clinicians navigated StrokEngine in search of information to answer questions on stroke assessment/intervention. Their search patterns were observed and clinicians provided verbal/written feedback about StrokEngine. Content analysis was used to generate themes and categorize them under two broad categories: facilitators and barriers to use. Five key facilitators and three key barriers to Strok-Engine use were identified and related to screen format, layout/organization, ease of navigation, quality of content, likelihood of using StrokEngine in the future, and system dysfunctions. All 14 clinicians were very or extremely satisfied with the layout/organization, quality and clinical relevance of the content, stating that they were likely to use StrokEngine in the future. All identified barriers from this study were addressed with website modifications in order to maximize the usability and navigability of StrokEngine. This rigorous methodology for usability testing can be applied during the design process of any e-learning resource.

Verification and Validation of Digitally Upgraded Control Rooms

International Nuclear Information System (INIS)

Boring, Ronald; Lau, Nathan

2015-01-01

As nuclear power plants undertake main control room modernization, a challenge is the lack of a clearly defined human factors process to follow. Verification and validation (V&V) as applied in the nuclear power community has tended to involve efforts such as integrated system validation, which comes at the tail end of the design stage. To fill in guidance gaps and create a step-by-step process for control room modernization, we have developed the Guideline for Operational Nuclear Usability and Knowledge Elicitation (GONUKE). This approach builds on best practices in the software industry, which prescribe an iterative user-centered approach featuring multiple cycles of design and evaluation. Nuclear regulatory guidance for control room design emphasizes summative evaluation - which occurs after the design is complete. In the GONUKE approach, evaluation is also performed at the formative stage of design - early in the design cycle using mockups and prototypes for evaluation. The evaluation may involve expert review (e.g., software heuristic evaluation at the formative stage and design verification against human factors standards like NUREG-0700 at the summative stage). The evaluation may also involve user testing (e.g., usability testing at the formative stage and integrated system validation at the summative stage). An additional, often overlooked component of evaluation is knowledge elicitation, which captures operator insights into the system. In this report we outline these evaluation types across design phases that support the overall modernization process. The objective is to provide industry-suitable guidance for steps to be taken in support of the design and evaluation of a new human-machine interface (HMI) in the control room. We suggest the value of early-stage V&V and highlight how this early-stage V&V can help improve the design process for control room modernization. We argue that there is a need to overcome two shortcomings of V&V in current practice

Verification and Validation of Digitally Upgraded Control Rooms

Energy Technology Data Exchange (ETDEWEB)

Boring, Ronald [Idaho National Lab. (INL), Idaho Falls, ID (United States); Lau, Nathan [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2015-09-01

As nuclear power plants undertake main control room modernization, a challenge is the lack of a clearly defined human factors process to follow. Verification and validation (V&V) as applied in the nuclear power community has tended to involve efforts such as integrated system validation, which comes at the tail end of the design stage. To fill in guidance gaps and create a step-by-step process for control room modernization, we have developed the Guideline for Operational Nuclear Usability and Knowledge Elicitation (GONUKE). This approach builds on best practices in the software industry, which prescribe an iterative user-centered approach featuring multiple cycles of design and evaluation. Nuclear regulatory guidance for control room design emphasizes summative evaluation—which occurs after the design is complete. In the GONUKE approach, evaluation is also performed at the formative stage of design—early in the design cycle using mockups and prototypes for evaluation. The evaluation may involve expert review (e.g., software heuristic evaluation at the formative stage and design verification against human factors standards like NUREG-0700 at the summative stage). The evaluation may also involve user testing (e.g., usability testing at the formative stage and integrated system validation at the summative stage). An additional, often overlooked component of evaluation is knowledge elicitation, which captures operator insights into the system. In this report we outline these evaluation types across design phases that support the overall modernization process. The objective is to provide industry-suitable guidance for steps to be taken in support of the design and evaluation of a new human-machine interface (HMI) in the control room. We suggest the value of early-stage V&V and highlight how this early-stage V&V can help improve the design process for control room modernization. We argue that there is a need to overcome two shortcomings of V&V in current practice�

Controlling the clean room atmosphere

International Nuclear Information System (INIS)

Meeks, R.F.

1979-01-01

Several types of clean rooms are commonly in use. They include the conventional clean room, the horizontal laminar flow clean room, the vertical laminar flow clean room and a fourth type that incorporates ideas from the previous types and is known as a clean air bench or hood. These clean rooms are briefly described. The origin of contamination and methods for controlling the contamination are discussed

Investigating Student Use and Value of E-Learning Resources to Develop Academic Writing within the Discipline of Environmental Science

Science.gov (United States)

Taffs, Kathryn H.; Holt, Julienne I.

2013-01-01

The use of information and communication technologies (ICTs) in higher education to support student learning is expanding. However, student usage has been low and the value of e-learning resources has been under investigation. We reflect on best practices for pedagogical design of e-learning resources to support academic writing in environmental…

An Assessment of Indoor Air Quality before, during and after Unrestricted Use of E-Cigarettes in a Small Room

Directory of Open Access Journals (Sweden)

Grant O'Connell

2015-05-01

Full Text Available Airborne chemicals in the indoor environment arise from a wide variety of sources such as burning fuels and cooking, construction materials and furniture, environmental tobacco smoke as well as outdoor sources. To understand the contribution of exhaled e-cigarette aerosol to the pre-existing chemicals in the ambient air, an indoor air quality study was conducted to measure volatile organic compounds (including nicotine and low molecular weight carbonyls, polycyclic aromatic hydrocarbons, tobacco-specific nitrosamines and trace metal levels in the air before, during and after e-cigarette use in a typical small office meeting room. Measurements were compared with human Health Criteria Values, such as indoor air quality guidelines or workplace exposure limits where established, to provide a context for potential bystander exposures. In this study, the data suggest that any additional chemicals present in indoor air from the exhaled e-cigarette aerosol, are unlikely to present an air quality issue to bystanders at the levels measured when compared to the regulatory standards that are used for workplaces or general indoor air quality.

An Assessment of Indoor Air Quality before, during and after Unrestricted Use of E-Cigarettes in a Small Room.

Science.gov (United States)

O'Connell, Grant; Colard, Stéphane; Cahours, Xavier; Pritchard, John D

2015-05-06

Airborne chemicals in the indoor environment arise from a wide variety of sources such as burning fuels and cooking, construction materials and furniture, environmental tobacco smoke as well as outdoor sources. To understand the contribution of exhaled e-cigarette aerosol to the pre-existing chemicals in the ambient air, an indoor air quality study was conducted to measure volatile organic compounds (including nicotine and low molecular weight carbonyls), polycyclic aromatic hydrocarbons, tobacco-specific nitrosamines and trace metal levels in the air before, during and after e-cigarette use in a typical small office meeting room. Measurements were compared with human Health Criteria Values, such as indoor air quality guidelines or workplace exposure limits where established, to provide a context for potential bystander exposures. In this study, the data suggest that any additional chemicals present in indoor air from the exhaled e-cigarette aerosol, are unlikely to present an air quality issue to bystanders at the levels measured when compared to the regulatory standards that are used for workplaces or general indoor air quality.

Mathematical modelling of a steam boiler room to research thermal efficiency

International Nuclear Information System (INIS)

Bujak, J.

2008-01-01

This paper introduces a mathematical model of a boiler room to research its thermal efficiency. The model is regarded as an open thermodynamic system exchanging mass, energy, and heat with the atmosphere. On those grounds, the energy and energy balance were calculated. Here I show several possibilities concerning how this model may be applied. Test results of the coefficient of thermal efficiency were compared to a real object, i.e. a steam boiler room of the Provincial Hospital in Wloclawek (Poland). The tests were carried out for 18 months. The results obtained in the boiler room were used for verification of the mathematical model

Control room lay-out

International Nuclear Information System (INIS)

Toma, Violeta

2004-01-01

TRIUMF (Tri-University Meson Facility) is Canada's national laboratory for particle and nuclear physics. There are 6 accelerators and 3 Control Rooms at TRIUMF. The main control room serves the big cyclotron, the 500 MeV, and the adjacent experiment. The 42 MeV and two 32 MeV ones are production dedicated. These cyclotrons belong to a private company but are operated by TRIUMF staff from ATG (Applied Technology Group) Control Room. The last is ISAC (Isotope Acceleration and Separation) Control Room, from which the LINAC is controlled. Research areas cover theoretical (2 subjects), pure (5 subjects) and applied (8 subjects) physics. In the early '70s, as the 500 MeV was being completed, the first Control Room was built in the main accelerator building. The recent topics covered by this paper are proton and pion therapy, what are the operator's duties?, the CP42, TR30 and TR13 cyclotron control rooms, the ISAC control systems including control room modification. Due to the nature of an operator's job, the Control Room layout is pretty important. This is true for any work environment, but when working shifts it becomes essential. Lots of time and effort, not to mention money, were spent to figure out the optimum configuration. It seems to me that the key factor in the control room layout is versatility, and this is because it has to keep happy a group of people with different inclinations, which have a tendency to become quite moody after the second night shift. No matter what, there will still be unhappy people, but we are trying our best. (Y. Tanaka)

Selective electrochemical extraction of REEs from NdFeB magnet waste at room temperature

NARCIS (Netherlands)

Venkatesan, P.; Vander Hoogerstraete, Tom; Hennebel, Tom; Binnemans, Koen; Sietsma, J.; Yang, Y.

2018-01-01

NdFeB magnet waste is one of the important secondary resources from which rare-earth elements (REEs) can be recovered. Herein we present an electrochemical route to selectively extract REEs from the magnet waste at room temperature. First, the magnet waste was partially leached with HCl. The

Y.E.S. International Entomology Resource Guide. Second Edition. Special Publication No. 2.

Science.gov (United States)

Dunn, Gary A., Comp.

This resource guide is designed to provide Young Entomologists' Society (Y.E.S.) members and other interested entomologists with information on people and companies that sell entomological equipment, supplies, services, preserved and dried specimens, livestock, books, publications, slides and other visuals, gift or novelty items, and…

Scheduling elective surgeries: the tradeoff among bed capacity, waiting patients and operating room utilization using goal programming.

Science.gov (United States)

Li, Xiangyong; Rafaliya, N; Baki, M Fazle; Chaouch, Ben A

2017-03-01

Scheduling of surgeries in the operating rooms under limited competing resources such as surgical and nursing staff, anesthesiologist, medical equipment, and recovery beds in surgical wards is a complicated process. A well-designed schedule should be concerned with the welfare of the entire system by allocating the available resources in an efficient and effective manner. In this paper, we develop an integer linear programming model in a manner useful for multiple goals for optimally scheduling elective surgeries based on the availability of surgeons and operating rooms over a time horizon. In particular, the model is concerned with the minimization of the following important goals: (1) the anticipated number of patients waiting for service; (2) the underutilization of operating room time; (3) the maximum expected number of patients in the recovery unit; and (4) the expected range (the difference between maximum and minimum expected number) of patients in the recovery unit. We develop two goal programming (GP) models: lexicographic GP model and weighted GP model. The lexicographic GP model schedules operating rooms when various preemptive priority levels are given to these four goals. A numerical study is conducted to illustrate the optimal master-surgery schedule obtained from the models. The numerical results demonstrate that when the available number of surgeons and operating rooms is known without error over the planning horizon, the proposed models can produce good schedules and priority levels and preference weights of four goals affect the resulting schedules. The results quantify the tradeoffs that must take place as the preemptive-weights of the four goals are changed.

Protocols for dry DNA storage and shipment at room temperature.

Science.gov (United States)

Ivanova, Natalia V; Kuzmina, Masha L

2013-09-01

The globalization of DNA barcoding will require core analytical facilities to develop cost-effective, efficient protocols for the shipment and archival storage of DNA extracts and PCR products. We evaluated three dry-state DNA stabilization systems: commercial Biomatrica(®) DNAstable(®) plates, home-made trehalose and polyvinyl alcohol (PVA) plates on 96-well panels of insect DNA stored at 56 °C and at room temperature. Controls included unprotected samples that were stored dry at room temperature and at 56 °C, and diluted samples held at 4 °C and at -20 °C. PCR and selective sequencing were performed over a 4-year interval to test the condition of DNA extracts. Biomatrica(®) provided better protection of DNA at 56 °C and at room temperature than trehalose and PVA, especially for diluted samples. PVA was the second best protectant after Biomatrica(®) at room temperature, whereas trehalose was the second best protectant at 56 °C. In spite of lower PCR success, the DNA stored at -20 °C yielded longer sequence reads and stronger signal, indicating that temperature is a crucial factor for DNA quality which has to be considered especially for long-term storage. Although it is premature to advocate a transition to DNA storage at room temperature, dry storage provides an additional layer of security for frozen samples, protecting them from degradation in the event of freezer failure. All three forms of DNA preservation enable shipment of dry DNA and PCR products between barcoding facilities. © 2013 The Authors. Molecular Ecology Resources published by John Wiley & Sons Ltd.

Measuring quality indicators in the operating room: cleaning and turnover time.

Science.gov (United States)

Jericó, Marli de Carvalho; Perroca, Márcia Galan; da Penha, Vivian Colombo

2011-01-01

This exploratory-descriptive study was carried out in the Surgical Center Unit of a university hospital aiming to measure time spent with concurrent cleaning performed by the cleaning service and turnover time and also investigated potential associations between cleaning time and the surgery's magnitude and specialty, period of the day and the room's size. The sample consisted of 101 surgeries, computing cleaning time and 60 surgeries, computing turnover time. The Kaplan-Meier method was used to analyze time and Pearson's correlation to study potential correlations. The time spent in concurrent cleaning was 7.1 minutes and turnover time was 35.6 minutes. No association between cleaning time and the other variables was found. These findings can support nurses in the efficient use of resources thereby speeding up the work process in the operating room.

Key facilitators and best practices of hotel-style room service in hospitals.

Science.gov (United States)

Sheehan-Smith, Lisa

2006-04-01

This qualitative study sought to identify the features, advantages, and disadvantages of hotel-style room service; the barriers to, and facilitators for, implementing the process; and "best practices." The study took place in four heterogeneous hospitals. Participants included hospital administrators, managers, and room-service employees. Data-collection methods included semi-structured interviews, observations, and document analysis. Common features of hotel-style room service were meal delivery within 30 to 45 minutes, a restaurant-style menu, procedures to feed ineligible patients, tray assembly on demand, scripting, and waitstaff uniforms for room-service employees. The major barrier to implementing room service was obtaining nursing support. The key facilitators were the hospital's service-oriented culture, using a multidisciplinary planning team, engaging nursing departments early in the planning stages, and intense customer-service training of room-service employees. The overwhelming advantage was patients' control over their food choices. The main disadvantage was cost. Initial best practices in hotel-style room service include: (a) taking a multidisciplinary team approach for developing and implementing the process, (b) customer-service training, (c) using a customer-driven menu, (d) wearing waitstaff uniforms, and (e) using carts with airpots for dispensing hot beverages.

Room Acoustical Fields

CERN Document Server

Mechel, Fridolin

2013-01-01

This book presents the theory of room acoustical fields and revises the Mirror Source Methods for practical computational use, emphasizing the wave character of acoustical fields.  The presented higher methods include the concepts of “Mirror Point Sources” and “Corner sources which allow for an excellent approximation of complex room geometries and even equipped rooms. In contrast to classical description, this book extends the theory of sound fields describing them by their complex sound pressure and the particle velocity. This approach enables accurate descriptions of interference and absorption phenomena.

CSIR eNews: Natural resources & the environment

CSIR Research Space (South Africa)

CSIR

2008-12-01

Full Text Available The CSIR conducts core research and develops competencies in various strategically critical areas of the natural resources and the environment (NRE) fields of study. Through relevant and focused research, CSIR Natural Resources and the Environment...

CSIR eNews: Natural resources and environment

CSIR Research Space (South Africa)

CSIR

2009-09-01

Full Text Available The CSIR conducts core research and develops competencies in various strategically critical areas of the natural resources and the environment (NRE) fields of study. Through relevant and focused research, CSIR Natural Resources and the Environment...

Virtual Seminar Room

DEFF Research Database (Denmark)

Forchhammer, Søren Otto; Fosgerau, Anders; Hansen, Peter Søren Kirk

1999-01-01

The initial design considerations and research goals for an ATM network based virtual seminar room with 5 sites are presented.......The initial design considerations and research goals for an ATM network based virtual seminar room with 5 sites are presented....

e-Assessment in a Limited-Resources Dental School Using an Open-Source Learning Management System.

Science.gov (United States)

El Tantawi, Maha M A; Abdelsalam, Maha M; Mourady, Ahmed M; Elrifae, Ismail M B

2015-05-01

e-Assessment provides solutions to some problems encountered in dental students' evaluation. The aim of this study was to evaluate the experience of a limited-resources dental school with e-assessment provided through an open-source learning management system (LMS). Data about users' access and types of e-assessment activities at the Faculty of Dentistry, Alexandria University, Egypt, were obtained from the web-based LMS Moodle. A questionnaire developed to assess students' perceptions of the e-assessment was also sent to students registered in two courses (undergraduate and postgraduate) with the same instructor. The results showed that most e-courses at the school had one form of e-assessment (82%) and, of these, 16.7% had summative assessment activities. There were significant differences among departments in the number of e-courses with e-assessment. One-quarter of e-courses with e-assessment used Moodle quizzes. Of 285 students registered in the two courses that included the questionnaire, 170 responded (response rate=59.6%). The responding students positively perceived the impact of e-assessment on learning and its reliability and security, whereas technical issues and related stresses were negatively perceived. This study suggests that e-assessment can be used at minimal cost in dental schools with limited resources and large class sizes with the least demands on faculty members and teaching staff time. For these schools, an open-source LMS such as Moodle provides formative e-assessment not available otherwise and accommodates various question formats and varying levels of instructors' technical skills. These students seemed to have a positive impression of the e-assessment although technical problems and related stresses are issues that need to be addressed.

Long-Term Stability Evaluation and Pillar Design Criterion for Room-and-Pillar Mines

Directory of Open Access Journals (Sweden)

Yang Yu

2017-10-01

Full Text Available The collapse of abandoned room-and-pillar mines is often violent and unpredictable. Safety concerns often resulted in mine closures with no post-mining stability evaluations. As a result, large amounts of land resources over room-and-pillar mines are wasted. This paper attempts to establish an understanding of the long-term stability issues of goafs (abandoned mines. Considering progressive pillar failures and the effect of single pillar failure on surrounding pillars, this paper proposes a pillar peeling model to evaluate the long-term stability of coal mines and the associated criteria for evaluating the long-term stability of room-and-pillar mines. The validity of the peeling model was verified by numerical simulation, and field data from 500 pillar cases from China, South Africa, and India. It is found that the damage level of pillar peeling is affected by the peel angle and pillar height and is controlled by the pillar width–height ratio.

Ventilation efficiency in a low-energy dwelling setting – a parameter study for larger rooms

NARCIS (Netherlands)

Dijkstra, D.; Loomans, M.G.L.C.; Hensen, J.L.M.; Cremers, B.E. (Bart)

2016-01-01

Mechanical balanced ventilation systems typically is applied in new and renovated dwellings in The Netherlands. The application assumes an adequate ventilation efficiency but this has not been confirmed for larger rooms (e.g. living rooms with kitchen attached). This study investigates ventilation

Some folded issues related to over-shielded and unplanned rooms for medical linear accelerators - A case study

Science.gov (United States)

Muhammad, Wazir; Ullah, Asad; Hussain, Amjad; Ali, Nawab; Alam, Khan; Khan, Gulzar; Matiullah; Maeng, Seongjin; Lee, Sang Hoon

2015-08-01

A medical linear accelerator (LINAC) room must be properly shielded to limit the outside radiation exposure to an acceptable safe level defined by individual state and international regulations. However, along with this prime objective, some additional issues are also important. The current case-study was designed to unfold the issues related to over-shielded and unplanned treatment rooms for LINACs. In this connection, an apparently unplanned and over-shielded treatment room of 610 × 610 cm2 in size was compared with a properly designed treatment room of 762 × 762 cm2 in size ( i.e., by following the procedures and recommendations of the IAEA Safety Reports Series No. 47 and NCRP 151). Evaluation of the unplanned room indicated that it was over-shielded and that its size was not suitable for total body irradiation (TBI), although the license for such a treatment facility had been acquired for the installed machine. An overall 14.96% reduction in the total shielding volume ( i.e., concrete) for an optimally planned room as compared to a non-planned room was estimated. Furthermore, the inner room's dimensions were increased by 25%, in order to accommodate TBI patients. These results show that planning and design of the treatment rooms are imperative to avoid extra financial burden to the hospitals and to provide enough space for easy and safe handling of the patients. A spacious room is ideal for storing treatment accessories and facilitates TBI treatment.

Experimental evaluation of air distribution in mechanically ventilated residential rooms

DEFF Research Database (Denmark)

Tomasi, R.; Krajčík, M.; Simone, A.

2013-01-01

The effect of low ventilation rates (1 or 0.5 air change per hour) on thermal comfort and ventilation effectiveness was experimentally studied in a simulated residential room equipped with radiant floor heating/cooling and mixing ventilation systems. The tests were performed for various positions...... of supply and extract air terminals and different winter and summer boundary conditions. Vertical air temperature, operative temperature and air velocity profiles were measured in different positions in the room, and equivalent temperatures were derived, in order to characterize thermal comfort. Contaminant...... with unconditioned outdoor air supply, i.e. at the supply air temperatures higher than the room air temperature. Moreover, low floor temperatures were needed to maintain the desired reference temperature in the stratified thermal environment. Mainly in cooling conditions the ventilation effectiveness depended...

Lessons from Evidence-Based Operating Room Management in Balancing the Needs for Efficient, Effective and Ethical Healthcare

OpenAIRE

Rosen, A.C.; Dexter, F.

2009-01-01

Foglia et al. (in press) describe tension in two veteran's hospitals among managers, clinicians, and patients over allocating appropriate resources to support care and inefficiencies in care delivery. Ultimately ethical healthcare in a system which is committed to caring for an entire population of patients must use its limited resources effectively while not compromising patient safety. This discussion gives examples from operating room management in which systematic analyses of existing dat...

Room-temperature synthesis of ultraviolet-emitting nanocrystalline GaN films using photochemical vapor deposition

International Nuclear Information System (INIS)

Yamazaki, Shunsuke; Yatsui, Takashi; Ohtsu, Motoichi; Kim, Taw-Won; Fujioka, Hiroshi

2004-01-01

We fabricated UV-emitting nanocrystalline gallium nitride (GaN) films at room temperature using photochemical vapor deposition (PCVD). For the samples synthesized at room temperature with V/III ratios exceeding 5.0x10 4 , strong photoluminescence peaks at 3.365 and 3.310 eV, which can be ascribed to transitions in a mixed phase of cubic and hexagonal GaN, were observed at 5 K. A UV emission spectrum with a full width at half-maximum of 100 meV was observed, even at room temperature. In addition, x-ray photoelectron spectroscopy measurement revealed that the film deposited by PCVD at room temperature was well nitridized

Heparin-mimicking multilayer coating on polymeric membrane via LbL assembly of cyclodextrin-based supramolecules.

Science.gov (United States)

Deng, Jie; Liu, Xinyue; Ma, Lang; Cheng, Chong; Shi, Wenbin; Nie, Chuanxiong; Zhao, Changsheng

2014-12-10

In this study, multifunctional and heparin-mimicking star-shaped supramolecules-deposited 3D porous multilayer films with improved biocompatibility were fabricated via a layer-by-layer (LbL) self-assembly method on polymeric membrane substrates. Star-shaped heparin-mimicking polyanions (including poly(styrenesulfonate-co-sodium acrylate; Star-PSS-AANa) and poly(styrenesulfonate-co-poly(ethylene glycol)methyl ether methacrylate; Star-PSS-EGMA)) and polycations (poly(methyl chloride-quaternized 2-(dimethylamino)ethyl methacrylate; Star-PMeDMA) were first synthesized by atom transfer radical polymerization (ATRP) from β-cyclodextrin (β-CD) based cores. Then assembly of 3D porous multilayers onto polymeric membrane surfaces was carried out by alternating deposition of the polyanions and polycations via electrostatic interaction. The surface morphology and composition, water contact angle, blood activation, and thrombotic potential as well as cell viability for the coated heparin-mimicking films were systematically investigated. The results of surface ATR-FTIR spectra and XPS spectra verified successful deposition of the star-shaped supramolecules onto the biomedical membrane surfaces; scanning electron microscopy (SEM) and atomic force microscopy (AFM) observations revealed that the modified substrate had 3D porous surface morphology, which might have a great biological influence on the biointerface. Furthermore, systematic in vitro investigation of protein adsorption, platelet adhesion, human platelet factor 4 (PF4, indicates platelet activation), activate partial thromboplastin time (APTT), thrombin time (TT), coagulation activation (thrombin-antithrombin III complex (TAT, indicates blood coagulant)), and blood-related complement activation (C3a and C5a, indicates inflammation potential) confirmed that the heparin-mimicking multilayer coated membranes exhibited ultralow blood component activations and excellent hemocompatibility. Meanwhile, after surface coating

Layer-by-layer assembly of nanostructured composites: Mechanics and applications

Science.gov (United States)

Podsiadlo, Paul

final part, we show preparation of high toughness and hierarchically organized NCs using two concepts: "exponential" LBL (e-LBL) assembly and charged polyurethanes. We show preparation of novel e-LBL structures and highly flexible LBL multilayers. We also demonstrate preparation of macro-scale composites from hierarchical, post-assembly consolidation of LBL sheets. This last result represents a potential paradigm change in the practice of LBL assembly by enabling transformation of the thin-films into macro-scale structures.

Exploring the Usefulness of e-Resources for Engineering College Teachers and Scholars for their Academic and Research Activities - A Study

Directory of Open Access Journals (Sweden)

Puttaswamy, R.M.

2014-03-01

Full Text Available The All India Council for Technical Education (AICTE, an apex body of controlling technical education in India, has made mandatory subscription of e-Resources to all its Engineering College Libraries. This policy has directly helped the teaching community, research scholars, and student's paternity, which has benefits for their teaching, research activities, and curriculum, respectively. This study emphasizes the usefulness of e-Resources among the teachers and scholars of engineering colleges in the Bangalore region under Visvesvaraya Technological University (VTU, Belgaum, Karnataka. Survey methodology has been used as the basic research tool for data collection with the help of questionnaires. 866 teaching faculties in VTU were selected randomly on the basis of willingness of users who access the e-Resources for their academic and research activities in the survey. The survey results were tabulated and analyzed with descriptive statistics methods using the SPSS 20 software package. The findings reveal that e-resources are useful for engineering college teachers and scholars for their academic and research activities.

19 September 2012 - Indonesian Members of Parliament visiting the CMS control room and experimental cavern at Point 5 with Former Deputy Spokesperson A. De Roeck and International Relations Adviser E. Tsesmelis.

CERN Multimedia

Jean-Claude Gadmer

2012-01-01

19 September 2012 - Indonesian Members of Parliament visiting the CMS control room and experimental cavern at Point 5 with Former Deputy Spokesperson A. De Roeck and International Relations Adviser E. Tsesmelis.

A Digital Library Example in the Digital Age: İstanbul Bilgi University Library and e-Resources

Directory of Open Access Journals (Sweden)

Banu Elçi

2015-06-01

Full Text Available This article describes the ongoing of the traditional library and service concept alteration to the library and service concept of the digital age and refers to an instance as İstanbul Bilgi University Library and e-Resources that pioneers technological advances and digital applications to be integrated into the library field. In this sense it involves services, developments, applications and projects provided by Bilgi Libraries.This article also accounts for a number of works which integrated digital resources and applications and social network interactions of the internet and the web of the digital age and how they are adjusted to the library area.In this context, it refers to an evolvement of a different approach of libraries and enhacements diverged from customary and adopted library service concepts and reveals through the medium of samples from İstanbul Bilgi University Library and e-Resources.

Public census data on CD-ROM at Lawrence Berkeley Laboratory. Revision 3

Energy Technology Data Exchange (ETDEWEB)

Merrill, D.W.

1993-01-16

The Comprehensive Epidemiologic Data Resource (CEDR) and Populations at Risk to Environmental Pollution (PAREP) projects, of the Information and Computing Sciences Division (ICSD) at Lawrence Berkeley Laboratory (LBL), are using public socioeconomic and geographic data files which are available to CEDR and PAREP collaborators via LBL`s computing network. At this time 72 CD-ROM diskettes (approximately 37 gigabytes) are on line via the Unix file server ``cedrcd.lbl.gov``. Most of the files are from the US Bureau of the Census, and many of these pertain to the 1990 Census of Population and Housing. All the CD-ROM diskettes contain documentation in the form of ASCII text files. In addition, printed documentation for most files is available for inspection at University of California Data and Technical Assistance (UC DATA), tel. (510) 642-6571, or the UC Documents Library, tel. (510) 642-2569, both located on the UC Berkeley Campus. Many of the CD-ROM diskettes distributed by the Census Bureau contain software for PC compatible computers, for easily accessing the data. Shared access to the data is maintained through a collaboration among the CEDR and PAREP projects at LBL, and UC DATA, and the UC Documents Library. LBL is grateful to UC DATA and the UC Documents Library for the use of their CD-ROM diskettes. Shared access to LBL facilities may be restricted in the future if costs become prohibitive. Via the Sun Network File System (NFS), these data can be exported to Internet computers for direct access by the user`s application program(s). Due to the size of the files, this access method is preferred over File Transfer Protocol (FTP) access. Please contact Deane Merrill (dwmerrill@lbl.gov) if you wish to make use of the data.

Public census data on CD-ROM at Lawrence Berkeley Laboratory

Energy Technology Data Exchange (ETDEWEB)

Merrill, D.W.

1993-01-16

The Comprehensive Epidemiologic Data Resource (CEDR) and Populations at Risk to Environmental Pollution (PAREP) projects, of the Information and Computing Sciences Division (ICSD) at Lawrence Berkeley Laboratory (LBL), are using public socioeconomic and geographic data files which are available to CEDR and PAREP collaborators via LBL's computing network. At this time 72 CD-ROM diskettes (approximately 37 gigabytes) are on line via the Unix file server cedrcd.lbl.gov''. Most of the files are from the US Bureau of the Census, and many of these pertain to the 1990 Census of Population and Housing. All the CD-ROM diskettes contain documentation in the form of ASCII text files. In addition, printed documentation for most files is available for inspection at University of California Data and Technical Assistance (UC DATA), tel. (510) 642-6571, or the UC Documents Library, tel. (510) 642-2569, both located on the UC Berkeley Campus. Many of the CD-ROM diskettes distributed by the Census Bureau contain software for PC compatible computers, for easily accessing the data. Shared access to the data is maintained through a collaboration among the CEDR and PAREP projects at LBL, and UC DATA, and the UC Documents Library. LBL is grateful to UC DATA and the UC Documents Library for the use of their CD-ROM diskettes. Shared access to LBL facilities may be restricted in the future if costs become prohibitive. Via the Sun Network File System (NFS), these data can be exported to Internet computers for direct access by the user's application program(s). Due to the size of the files, this access method is preferred over File Transfer Protocol (FTP) access. Please contact Deane Merrill (dwmerrill lbl.gov) if you wish to make use of the data.

CSN's New Emergency Room

International Nuclear Information System (INIS)

Sendin, P.

2005-01-01

During the month of July 2005 the physical renovation works and technological updating of the basic infrastructures of the CSN Emergency Room (SALEM) were finished, allowing the Room to now have greater functionality and a broader technical capacity. Nevertheless, the technological improvement process of SALEM will reach its full potential within the next few years, once the installation currently underway of the new information integration and monitoring systems and the decision making support systems have been completed. This article describes the improvements introduced to the Room and the objectives pursued in this renovation project to convert the SALEM into a new generation room in accordance with its current technological context. (Author) 4 refs

Our Urban Living Room

DEFF Research Database (Denmark)

Hjortshøj, Rasmus

2016-01-01

Our Urban Living Room is an exhibition and a book, created by Cobe. The theme is based on Cobe’s ten years of practice, grounded in social livability and urban democracy, and our aim to create buildings and spaces that invite Copenhageners to use and define them; as an extended living room, where...... the boundaries between private and public space become fluid. Based on specific Cobe projects, Our Urban Living Room tells stories about the architectural development of Copenhagen, while exploring the progression of the Danish Capital - from an industrial city into an urban living room, known as one...... of the world’s most livable places. Photography by Rasmus Hjortshøj....

Environmental Survey preliminary report, Lawrence Berkeley Laboratory, Berkeley, California

International Nuclear Information System (INIS)

1988-07-01

The purpose of this report is to present the preliminary findings made during the Environmental Survey, February 22--29, 1988, at the US Department of Energy (DOE) Lawrence Berkeley Laboratory (LBL) in Berkeley, California. The University of California operates the LBL facility for DOE. The LBL Survey is part of the larger DOE-wide Environmental Survey announced by Secretary John S. Herrington on September 18, 1985. The purpose of this effort is to identify, via ''no fault'' baseline Surveys, existing environmental problems and areas of environmental risk at DOE facilities, and to rank them on a DOE wide basis. This ranking will enable DOE to more effectively establish priorities for addressing environmental problems and allocate the resources necessary to correct them. Because the Survey is ''no fault'' and is not an ''audit,'' it is not designed to identify specific isolated incidents of noncompliance or to analyze environmental management practices. Such incidents and/or management practices will, however, be used in the Survey as a means of identifying existing and potential environmental problems. The LBL Survey was conducted by a multidisciplinary team of technical specialists headed and managed by a Team Leader and Assistant Team Leader from DOE's Office of Environmental Audit. A complete list of the LBL Survey participants and their affiliations is provided in Appendix A. 80 refs., 27 figs., 37 tabs

Environmental Survey preliminary report, Lawrence Berkeley Laboratory, Berkeley, California

Energy Technology Data Exchange (ETDEWEB)

1988-07-01

The purpose of this report is to present the preliminary findings made during the Environmental Survey, February 22--29, 1988, at the US Department of Energy (DOE) Lawrence Berkeley Laboratory (LBL) in Berkeley, California. The University of California operates the LBL facility for DOE. The LBL Survey is part of the larger DOE-wide Environmental Survey announced by Secretary John S. Herrington on September 18, 1985. The purpose of this effort is to identify, via no fault'' baseline Surveys, existing environmental problems and areas of environmental risk at DOE facilities, and to rank them on a DOE wide basis. This ranking will enable DOE to more effectively establish priorities for addressing environmental problems and allocate the resources necessary to correct them. Because the Survey is no fault'' and is not an audit,'' it is not designed to identify specific isolated incidents of noncompliance or to analyze environmental management practices. Such incidents and/or management practices will, however, be used in the Survey as a means of identifying existing and potential environmental problems. The LBL Survey was conducted by a multidisciplinary team of technical specialists headed and managed by a Team Leader and Assistant Team Leader from DOE's Office of Environmental Audit. A complete list of the LBL Survey participants and their affiliations is provided in Appendix A. 80 refs., 27 figs., 37 tabs.

Gas explosion in a room with a window and passage to an adjacent room

Directory of Open Access Journals (Sweden)

Polandov Yuri

2016-01-01

Full Text Available Some publications describe an effect, produced during a physical model experiment, when an adjacent gas-free room influences the gas explosion pressure in a room with a window. The explosion pressure in this case significantly exceeds (2.5 times the explosion pressure in a room without an adjacent room. This result has been confirmed by our studies. Based on other available information about the influence of the ignition point location on the explosion pressure in one room, it was suggested that this could be true for an explosion in two rooms. In our studies we used a test unit with two connected chambers, each having a volume of 1.125 m3. It turned out that this influence of the adjacent volume was not so unambiguous as it was described in those publications. It was found out that the maximum effect of explosion pressure amplification by the adjacent room is achieved, when the igniter is located in the chamber filled with a gas-air mixture in the area between the center of the chamber and the window (maximum amplification by more than 3 times. This effect is lower directly by the window (1.8 times and is practically absent in case of ignition within the area near the passage connecting the chamber with the adjacent room. This suggests that the effect discovered earlier is a special case of the general dependence of the gas explosion pressure in two chambers on the igniter location.

Surgical team turnover and operative time: An evaluation of operating room efficiency during pulmonary resection.

Science.gov (United States)

Azzi, Alain Joe; Shah, Karan; Seely, Andrew; Villeneuve, James Patrick; Sundaresan, Sudhir R; Shamji, Farid M; Maziak, Donna E; Gilbert, Sebastien

2016-05-01

Health care resources are costly and should be used judiciously and efficiently. Predicting the duration of surgical procedures is key to optimizing operating room resources. Our objective was to identify factors influencing operative time, particularly surgical team turnover. We performed a single-institution, retrospective review of lobectomy operations. Univariate and multivariate analyses were performed to evaluate the impact of different factors on surgical time (skin-to-skin) and total procedure time. Staff turnover within the nursing component of the surgical team was defined as the number of instances any nurse had to leave the operating room over the total number of nurses involved in the operation. A total of 235 lobectomies were performed by 5 surgeons, most commonly for lung cancer (95%). On multivariate analysis, percent forced expiratory volume in 1 second, surgical approach, and lesion size had a significant effect on surgical time. Nursing turnover was associated with a significant increase in surgical time (53.7 minutes; 95% confidence interval, 6.4-101; P = .026) and total procedure time (83.2 minutes; 95% confidence interval, 30.1-136.2; P = .002). Active management of surgical team turnover may be an opportunity to improve operating room efficiency when the surgical team is engaged in a major pulmonary resection. Copyright © 2016 The American Association for Thoracic Surgery. Published by Elsevier Inc. All rights reserved.

Human Factors Engineering Aspects of Modifications in Control Room Modernization

Energy Technology Data Exchange (ETDEWEB)

Hugo, Jacques [Idaho National Lab. (INL), Idaho Falls, ID (United States); Clefton, Gordon [Idaho National Lab. (INL), Idaho Falls, ID (United States); Joe, Jeffrey [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2017-06-01

This report describes the basic aspects of control room modernization projects in the U.S. nuclear industry and the need for supplementary guidance on the integration of human factors considerations into the licensing and regulatory aspects of digital upgrades. The report pays specific attention to the integration of principles described in NUREG-0711 (Human Factors Engineering Program Review Model) and how supplementary guidance can help to raise general awareness in the industry regarding the complexities of control room modernization projects created by many interdependent regulations, standards and guidelines. The report also describes how human factors engineering principles and methods provided by various resources and international standards can help in navigating through the process of licensing digital upgrades. In particular, the integration of human factors engineering guidance and requirements into the process of licensing digital upgrades can help reduce uncertainty related to development of technical bases for digital upgrades that will avoid the introduction of new failure modes.

Medical and biohazardous waste generator`s guide: Revision 1

Energy Technology Data Exchange (ETDEWEB)

1994-09-01

This Guide describes the procedures required to comply with all federal and state laws and regulations and Lawrence Berkeley Laboratory (LBL) policy applicable to medical and biohazardous waste. The members of the LBL Biological Safety Subcommittee participated in writing these policies and procedures. The procedures and policies in this Guide apply to LBL personnel who work with infectious agents or potentially infectious agents, publicly perceived infectious items or materials (e.g., medical gloves, culture dishes), and sharps (e.g., needles, syringes, razor blades). If medical or biohazardous waste is contaminated or mixed with a hazardous chemical or material, with a radioactive material, or with both, the waste will be handled in accordance with the applicable federal and State of California laws and regulations for hazardous, radioactive, or mixed waste.

Medical and biohazardous waste generator's guide: Revision 1

International Nuclear Information System (INIS)

1994-09-01

This Guide describes the procedures required to comply with all federal and state laws and regulations and Lawrence Berkeley Laboratory (LBL) policy applicable to medical and biohazardous waste. The members of the LBL Biological Safety Subcommittee participated in writing these policies and procedures. The procedures and policies in this Guide apply to LBL personnel who work with infectious agents or potentially infectious agents, publicly perceived infectious items or materials (e.g., medical gloves, culture dishes), and sharps (e.g., needles, syringes, razor blades). If medical or biohazardous waste is contaminated or mixed with a hazardous chemical or material, with a radioactive material, or with both, the waste will be handled in accordance with the applicable federal and State of California laws and regulations for hazardous, radioactive, or mixed waste

Evaluating the auralization of a small room in a virtual sound environment using objective room acoustic measures

DEFF Research Database (Denmark)

Ahrens, Axel; Marschall, Marton; Dau, Torsten

2016-01-01

To study human auditory perception in realistic environments, loudspeaker-based reproduction techniques have recently become state-of-the-art. To evaluate the accuracy of a simulation-based room auralization of a small room, objective measures, such as early-decay-time (EDT), reverberation time...... of the room. The auralizations were generated using the loudspeaker-based room auralization toolbox (LoRA; Favrot and Buchholz, 2010) and reproduced in a 64-channel loudspeaker array, set up in an anechoic chamber. Differences between the objective measures evaluated in the real and the virtual room were......, clarity, interaural cross-correlation (IACC), and the speech transmission index were measured in an IEC listening room for 28 source-receiver combinations. The room was then modeled in the room acoustics software ODEON, and the same objective measures were also evaluated for the auralized version...

Radiation Protection Elephants in the Room

International Nuclear Information System (INIS)

Vetter, R. J.

2004-01-01

As our system of radiological protection evolves, several significant issues loom within radiation protection discussions and publications. These issues influence the nature of epidemiological and radiobiological research and the establishment of radiation protection recommendations, standards, and regulations. These issues are like the proverbial e lephants in the room . They are large, and it is unwise to ignore them. This paper discusses the impact of three young elephants as they make their presence increasingly obvious: increased cancer susceptibility from early-life exposure to radiation, terrorism and fear of radiation, and patient safety. Increased cancer susceptibility from early-life exposure to radiation is emerging as a discussion topic related to the safety of computed tomography (CT) and other medical modalities. Shortly after publication of CT dose data, manufacturers were helping to reduce doses to children by increasing flexibility for adjustment of technique factors. Also, radiation epidemiological data are being used in the development of guidance on exposure to chemical carcinogens during early life. Re-emergence of public fear of radiation has been fueled by threats of radiological dispersion devises and confusing messages about personal decontamination, emergency room acceptance or rejection of contaminated victims, and environmental clean-up. Finally, several professional publications have characterized risk of medical radiation exposure in terms of patient deaths even though epidemiological data do not support such conclusions. All three of these elephants require excellent science and sophisticated data analysis to coax them from the room. Anecdotal communications that confuse the public should be avoided. These are not the only elephants in the room, but these three are making their presence increasingly obvious. This paper discusses the need for radiation protection professionals to rely on good science in the evolution of the system of

Reflections of health care professionals on e-learning resources for patient safety.

Science.gov (United States)

Walsh, Kieran

2018-01-01

There is a paucity of evidence on how health care professionals view e-learning as a means of education to achieve safer health care. To address this gap, the reflections of health care professionals who used the resources on BMJ Learning were captured and analyzed. Key themes emerged from the analysis. Health care professionals are keen to put their e-learning into action to achieve safer health care and to learn how to follow guidelines that will help them achieve safer health care. Learners wanted their learning to remain grounded in reality. Finally, many commented that it was difficult for their individual learning to have a real impact when the culture of the organization did not change.

An investigation on e-resource utilisation among university students in a developing country: A case of Great Zimbabwe University

Directory of Open Access Journals (Sweden)

Talent Mawere

2018-06-01

Full Text Available Background: Electronic libraries are the recent development in the ever-changing technological world today. Students nowadays have the ability to carry the library wherever they are, their Internet-enabled devices being the only requirement. Most universities worldwide have subscribed to various online databases and other e-resources as a way of availing resources to their students. To their credit, most institutions of higher learning in developing countries have not been left out in this stampede.   Objectives: The study aimed at investigating the adoption and utilisation of e-resources by students at a university in a developing country.   Method: The Technology Acceptance Model (TAM model was used to conceptualise the study. A survey questionnaire was designed and distributed through social media platforms such as Facebook and WhatsApp. Quantitative data were analysed using the Statistical Package for the Social Sciences (SPSS. The Chi-squared test was used to test for casual relationships within the developed model. A thematic approach was used to analyse qualitative data. Results: Despite the fact that many Zimbabwean academic institutions have made the facility of e-libraries top agenda in their strategic plans, the adoption rate among students is still very limited. This can be attributed to a myriad of facts, inter alia, poor marketing strategies, lack of resources among the students and exorbitant data charges by Internet Service Providers (ISPs.   Conclusion: This study has provided some basic insights in utilisation of e-resources in universities of developing countries. Despite the younger generation being described as digital natives, it is, quite evident that their uptake of technological innovations especially in education is quite poor. This research will assist both researchers and management of institutions of higher learning to provide and design amicable solutions to the problem of poor utilisation of e-resources as

Safety measures in exposure room

International Nuclear Information System (INIS)

Muhammad Jamal Md Isa

2004-01-01

The contents of this chapter are follows - The exposure room: location and dimension, material and thickness, windows, doors and other openings; Position of the Irradiating Apparatus, Use of Space Adjoining the Room, Warning Signs/Light, Dark Room. Materials and Apparatus: Classification of Areas, Local Rules, Other General Safety Requirements

Macromolecular shape and interactions in layer-by-layer assemblies within cylindrical nanopores.

Science.gov (United States)

Lazzara, Thomas D; Lau, K H Aaron; Knoll, Wolfgang; Janshoff, Andreas; Steinem, Claudia

2012-01-01

Layer-by-layer (LbL) deposition of polyelectrolytes and proteins within the cylindrical nanopores of anodic aluminum oxide (AAO) membranes was studied by optical waveguide spectroscopy (OWS). AAO has aligned cylindrical, nonintersecting pores with a defined pore diameter d(0) and functions as a planar optical waveguide so as to monitor, in situ, the LbL process by OWS. The LbL deposition of globular proteins, i.e., avidin and biotinylated bovine serum albumin was compared with that of linear polyelectrolytes (linear-PEs), both species being of similar molecular weight. LbL deposition within the cylindrical AAO geometry for different pore diameters (d(0) = 25-80 nm) for the various macromolecular species, showed that the multilayer film growth was inhibited at different maximum numbers of LbL steps (n(max)). The value of n(max) was greatest for linear-PEs, while proteins had a lower value. The cylindrical pore geometry imposes a physical limit to LbL growth such that n(max) is strongly dependent on the overall internal structure of the LbL film. For all macromolecular species, deposition was inhibited in native AAO, having pores of d(0) = 25-30 nm. Both, OWS and scanning electron microscopy showed that LbL growth in larger AAO pores (d(0) > 25-30 nm) became inhibited when approaching a pore diameter of d(eff,n_max) = 25-35 nm, a similar size to that of native AAO pores, with d(0) = 25-30 nm. For a reasonable estimation of d(eff,n_max), the actual volume occupied by a macromolecular assembly must be taken into consideration. The results clearly show that electrostatic LbL allowed for compact macromolecular layers, whereas proteins formed loosely packed multilayers.

Fire protection for clean rooms

International Nuclear Information System (INIS)

Kirson, D.

1990-01-01

The fire protection engineer often must decide what size fire can be tolerated before automatic fire suppression systems actuate. Is it a wastepaper basket fire, a bushel basket fire...? In the case of state-of-the-art clean rooms, the answer clearly is not even an incipient fire. Minor fires in clean rooms can cause major losses. This paper discusses what a clean room is and gives a brief overview of the unique fire protection challenges encountered. The two major causes of fire related to clean rooms in the semiconductor industry are flammable/pyrophoric gas fires in plastic ducts and polypropylene wet bench fires. This paper concentrates on plastic ductwork in clean rooms, sprinkler protection in ductwork, and protection for wet benches

e73.pdf.pdf | 92 | OnlineResources | jgenet | www.ias.ac.in | http ...

Indian Academy of Sciences (India)

Home; public; Volumes; jgen; 092; online; http; www.ias.ac.in; jgenet; OnlineResources; 92; e73.pdf.pdf. 404! error. The page your are looking for can not be found! Please check the link or use the navigation bar at the top. YouTube; Twitter; Facebook; Blog. Academy News. IAS Logo. 29th Mid-year meeting. Posted on 19 ...

Room for caring

DEFF Research Database (Denmark)

Timmermann, Connie; Uhrenfeldt, Lisbeth; Birkelund, Regner

2015-01-01

Aim This study explores how seriously ill hospitalized patients' experience and assign meaning to their patient room. Background Modern hospitals and the rational underlying care and treatment of today have their emphasis on diagnosis, cure and treatment. Consequently, aesthetics in the patient...... rooms such as a view of nature or natural light entering the room are often neglected in caring for these patients. Method A phenomenological-hermeneutic study design was applied and data was collected through multiple qualitative interviews combined with observations at a teaching hospital in Denmark......-being, relief and hope for the patients during serious illness. Therefore, these sensory impressions should be thought of as holding palliative potential and should be included as a part of caring for the seriously ill patients....

Control room design

International Nuclear Information System (INIS)

Zinke, H.

1980-01-01

To control a 1300 megawatt nuclear power plant, about 15000 plant parameters must be collected together to control and operate the plant. The control room design therefore is of particular importance. The main design criteria are: Required functions of the power plant process - Level of Automation - Ergonomics - Available Technology. Extensive analysis has resulted in a control room design method. This ensures that an objective solution will be reached. Resulting from this methodical approach are: 1. Scope, position and appearance of the instrumentation. 2. Scope, position and appearance of the operator controls. Process analysis dictates what instrumentation and operator controls are needed. The priority and importance of the control and instrumentation (this we define as the utilisation areas), dictates the rough layout of the control room. (orig./RW)

Patient mix optimisation for inpatient planning with multiple resources

NARCIS (Netherlands)

Vissers, J.M.H.; Adan, I.J.B.F.; Dellaert, N.P.; Jeunet, J.; Bekkers, J.A.; Tanfani, E.; Testi, A.

2012-01-01

This contribution addresses the planning of admissions of surgical patients, requiring different resources such as beds and nursing capacity at wards, operating rooms and operating theatre personnel at an operating theatre, intensive care beds and intensive care nursing capacity at an intensive care

First installation of a dual-room IVR-CT system in the emergency room.

Science.gov (United States)

Wada, Daiki; Nakamori, Yasushi; Kanayama, Shuji; Maruyama, Shuhei; Kawada, Masahiro; Iwamura, Hiromu; Hayakawa, Koichi; Saito, Fukuki; Kuwagata, Yasuyuki

2018-03-05

Computed tomography (CT) embedded in the emergency room has gained importance in the early diagnostic phase of trauma care. In 2011, we implemented a new trauma workflow concept with a sliding CT scanner system with interventional radiology features (IVR-CT) that allows CT examination and emergency therapeutic intervention without relocating the patient, which we call the Hybrid emergency room (Hybrid ER). In the Hybrid ER, all life-saving procedures, CT examination, damage control surgery, and transcatheter arterial embolisation can be performed on the same table. Although the trauma workflow realized in the Hybrid ER may improve mortality in severe trauma, the Hybrid ER can potentially affect the efficacy of other in/outpatient diagnostic workflow because one room is occupied by one severely injured patient undergoing both emergency trauma care and CT scanning for long periods. In July 2017, we implemented a new trauma workflow concept with a dual-room sliding CT scanner system with interventional radiology features (dual-room IVR-CT) to increase patient throughput. When we perform emergency surgery or interventional radiology for a severely injured or ill patient in the Hybrid ER, the sliding CT scanner moves to the adjacent CT suite, and we can perform CT scanning of another in/outpatient. We believe that dual-room IVR-CT can contribute to the improvement of both the survival of severely injured or ill patients and patient throughput.

Learners' Perceptions on the Structure and Usefulness of E-Resources for the Thesis Courses

Science.gov (United States)

Aghaee, Naghmeh; Hansson, Henrik; Tedre, Matti; Drougge, Ulrika

2014-01-01

The use of information and communication technology (ICT) in education is a way to facilitate interaction and accessing information for learning in higher education. However, finding a set of structured e-resources to facilitate learning within specific courses is still a big challenge in most higher education institutions. This includes the…

Investigating Predictors of Pre-Service Science Teachers' Behavioral Intention toward e-Resources for Teaching

Science.gov (United States)

Shittu, Ahmed Tajudeen; Kareem, Bamidele Wahab; Obielodan, Omotayo Olabo; Fakomogbon, Michael Ayodele

2017-01-01

This study examined predictors of pre-service science teachers' behavioral intention toward e-resources use for teaching in Nigeria. The study used cross-sectional survey research method and a questionnaire with a set of items that measure technology preparedness, perceived usefulness, perceived ease of use and behavioral intention to gather the…

The Virtual Dressing Room

DEFF Research Database (Denmark)

Holte, Michael Boelstoft; Gao, Yi; Petersson, Eva

2015-01-01

This paper presents the design and evaluation of a usability and user experience test of a virtual dressing room. First, we motivate and introduce our recent developed prototype of a virtual dressing room. Next, we present the research and test design grounded in related usability and user...... experience studies. We give a description of the experimental setup and the execution of the designed usability and user experience test. To this end, we report interesting results and discuss the results with respect to user-centered design and development of a virtual dressing room....

Building a Smooth Medical Service for Operating Room Using RFID Technologies

Directory of Open Access Journals (Sweden)

Lun-Ping Hung

2014-01-01

Full Text Available Due to the information technology advancement, the feasibility for the establishment of mobile medical environments has been strengthened. Using RFID to facilitate the tracing of patients’ mobile position in hospital has attracted more attentions from researchers due to the demand on advanced features. Traditionally, the management of surgical treatment is generally manually operated and there is no consistent operating procedure for patients transferring among wards, surgery waiting rooms, operating rooms, and recovery rooms, resulting in panicky and urgent transferring work among departments and, thus, leading to delays and errors. In this paper, we propose a new framework using radio frequency identification (RFID technology for a mobilized surgical process monitoring system. Through the active tag, an application management system used before, during, and after the surgical processes has been proposed. The concept of signal level matrix, SLM, was proposed to accurately identify patients and dynamically track patients’ location. By updating patient’s information real-time, the preprocessing time needed for various tasks and incomplete transfers among departments can be reduced, the medical resources can be effectively used, unnecessary medical disputes can be reduced, and more comprehensive health care environment can be provided. The feasibility and effectiveness of our proposed system are demonstrated with a number of experimental results.

Public census data on CD-ROM at Lawrence Berkeley Laboratory. Revision 4

Energy Technology Data Exchange (ETDEWEB)

Merrill, D.W.

1993-03-12

The Comprehensive Epidemiologic Data Resource (CEDR) and Populations at Risk to Environmental Pollution (PAREP) projects, of the Information and Computing sciences Division (ICSD) at Lawrence Berkeley Laboratory (LBL), are using public socioeconomic and geographic data files which are available to CEDR and PAREP collaborators via LBL`s computing network. At this time 89 CD-ROM diskettes (approximately 45 gigabytes) are on line via the Unix file server cedrcd.lbl.gov. Most of the files are from the US Bureau of the Census, and many of these pertain to the 1990 Census of Population and Housing. All the CD-ROM diskettes contain documentation in the form of ASCII text files. In addition, printed documentation for most files is available for inspection at University of California Data and Technical Assistance (UC DATA), tel. (510) 642-6571, or the UC Documents Library, tel. (510) 642-2569, both located on the UC Berkeley Campus. Many of the CD-ROM diskettes distributed by the Census Bureau contain software for PC compatible computers, for easily accessing the data. Shared access to the data is maintained through a collaboration among the CEDR and PAREP projects at LBL, and UC DATA, and the UC Documents Library. LBL is grateful to UC DATA and the UC Documents Library for the use of their CD-ROM diskettes. Shared access to LBL facilities may be restricted in the future if costs become prohibitive. Via the Sun Network File System (NFS), these data can be exported to Internet computers for direct access by the user`s application program(s). Due to the size of the files, this access method is preferred over File Transfer Protocol (FTP) access.

Deutsch, Doyc or Doitsch? Chatters as Languagers--The Case of a German-Turkish Chat Room

Science.gov (United States)

Hinnenkamp, Volker

2008-01-01

The paper looks at the process of online-languaging of adolescents with a migratory and ethnic Turkish background in a diasporic chat room. The multiple resources and voices used are analysed. One particular example is looked at more thoroughly to illustrate the process of languaging and how it is legitimised by the chatters themselves. Finally,…

Marcoule pilot work-room: process automatic operation

International Nuclear Information System (INIS)

Mus, G.; Linger, C.

1987-01-01

Commissioned in the early 1960s, the Marcoule Pilot Plant has undergone a series of sweeping transformations. The Research and Development resources concerning irradiated fuel processing have been expanded and modified. Its reprocessing capacity has also been raised from 2 to 5 t/year. Simultaneously, the installation control system was completely remodelled. The control consoles, which were previously positioned locally near the different units, have been grouped together in a centralized control room. To do this, the measurement and operating circuits were replaced by new data acquisition and processing systems requiring the use of numerical algorithms. The management and control of certain units, including mechanical fuel preparation, sampling, and sample transport to the laboratories, have been entrusted to programmable automata. Certain unit operations, such as concentration by evaporation, are set up with complete automation. These new arrangements will expand the resources for analysing the operation of the Pilot Plant, while offering a more overall view of the operations. They have been made possible by a major effort in the development of sensors, and represent the indispensable prerequisite for the installation of expert systems [fr

Control room habitability assessment and in-leakage test for Korean NPP - 15510

International Nuclear Information System (INIS)

Song, D.S.; Lee, J.B.; Ha, S.J.; Seong, J.J.

2015-01-01

The assessment of control room habitability for Wolsung unit 1 was performed based on GL 2003-01 and Reg. Guide 1.197. The control room habitability program including Control Room Envelope (CRE) in-leakage test procedures, self assessment guidance, CRE boundary control program, CRE maintenance/sealing program was developed for Wolsung unit 1. The integrated CRE test was performed utilizing ASTM E741. There are two operating modes of pressurization and isolation for CRE ventilation test, and four tests were performed using each of the control room HVAC sub-trains. The control room HVAC system lineup of pressurization mode test was based upon a lineup that encompassed the design basis radiological analyses. The other control room HVAC system lineup of isolation mode test was based on an operation mode that considers toxic gas. The in-leakage testing was performed in accordance with CRE in-leakage test procedures. In the pressurization mode, measured unfiltered in-leakage rates for train A and train B were 0 CFM and 405 CFM respectively. In the isolation mode, measured unfiltered in-leakage rates for train A and train B were 1,739 CFM and 1,502 CFM, respectively. Maximum concentration of ammonia at the control room HVAC intake is calculated to be 0.027 g/m 3 (39 ppm), and satisfied the toxicity limit of 300 ppm. The test result shows that the measured unfiltered in-leakage is bounded by the regulatory criteria assumed in the design basis radiological analyses. (authors)

Control room habitability during severe accidents

International Nuclear Information System (INIS)

Siu, R.P.

1989-01-01

The requirements for protection of control room personnel against radiation hazards are specified in 10CFR50, Appendix A, GDC 19. The conventional approach involves a mechanistic evaluation of the radiation doses to control room personnel during design-basis accidents. In this study, an assessment of control room habitability during severe accidents is conducted. The potential levels of radiation hazards to control room personnel are evaluated in terms of both magnitude and probability of occurrence. The expected values for the probabilities of exceeding GDC-19 limits and the cumulative probability distributions of control room doses are determined. In this study, a pressurized water reactor with a large dry containment has been selected for analysis. The types of control rooms evaluated in this study include designs with: (a) filtered local intakes only, (b) filtered recirculation only, (c) filtered local intakes and recirculation, and (d) filtered dual remote intakes and recirculation. From the observations, it is concluded that, except for control room D, all other control room designs may require improvements in order to provide adequate radiation protection during severe accidents, particularly in terms of reducing whole-body gamma doses and skin doses. Potential design improvements include reduction of intake flows for concepts relying on pressurization, reduction in overall leakages, and control room pressurization through the use of bottled air supply

Using Ontologies for the E-learning System in Healthcare Human Resources Management

Directory of Open Access Journals (Sweden)

Lidia BAJENARU

2015-01-01

Full Text Available This paper provides a model for the use of ontology in e-learning systems for structuring educational content in the domain of healthcare human resources management (HHRM in Romania. In this respect we propose an effective method to improve the learning system by providing personalized learning paths created using ontology and advanced educational strategies to provide a personalized learning content for the medical staff. Personalization of e-learning process for the chosen target group will be achieved by setting up learning path for each user according to his profile. This will become possible using: domain ontology, learning objects, modeling student knowledge. Developing an ontology-based system for competence management allows complex interactions, providing intelligent interfacing. This is a new approach for the healthcare system managers in permanent training based on e-learning technologies and specific ontologies in a complex area that needs urgent modernization and efficiency to meet the public health economic, social and political context of Romania.

Impact of turbulence anisotropy near walls in room airflow

DEFF Research Database (Denmark)

Schälin, A.; Nielsen, Peter Vilhelm

2004-01-01

The influence of different turbulence models used in computational fluid dynamics predictions is studied in connection with room air movement. The turbulence models used are the high Re-number k–e model and the high Re- number Reynolds stress model (RSM). The three-dimensional wall jet is selected...... in a three- dimensional wall jet by the k–e turbulence model. Furthermore, it is shown that the growth rate can be predicted to a certain extent by the RSM with wall reflection terms. The flow in a deep room can be strongly influenced by details as the growth rate of a three-dimensional wall jet. Predictions...... for the work. The growth rate parallel to the wall in a three-dimensional wall jet is large compared with the growth rate perpendicular to the wall, and it is large compared with the growth rate in a free circular jet. It is shown that it is not possible to predict the high growth rate parallel with a surface...

Films and dark room

International Nuclear Information System (INIS)

Abdul Nassir Ibrahim; Azali Muhammad; Ab. Razak Hamzah; Abd. Aziz Mohamed; Mohamad Pauzi Ismail

2008-01-01

After we know where the radiographic come from, then we must know about the film and also dark room. So, this chapter 5 discusses the two main components for radiography work that is film and dark room, places to process the film. Film are structured with three structured that are basic structured, emulsion and protection structured. So, this film can be classified either with their speed, screen and standard that used. The process to wash the film must be done in dark room otherwise the radiographer cannot get what are they inspected. The processing of film will be discussed briefly in next chapter.

The conference hybrid control room

International Nuclear Information System (INIS)

Gieci, A.; Caucik, J.; Macko, J.

2008-01-01

An original concept of a hybrid control room was developed for the Mochovce-3 and Mochovce-4 reactor units which are under construction. The basic idea underlying the concept is that the control room should be a main working place for the operators (reactor operator and turbine operator) and for the shift supervisor, designed as a comprehensive unit desk shaped so that all members of the control room crew are in a face-to-face contact constantly. The main desk consists of three clearly identified areas serving the operators and the unit supervisor as their main working places. A soft control system is installed at the main working places. A separate safety-related working place, designed as a panel with classical instrumentations at the conference hybrid control room, is provided in case of abnormal conditions or emergency situation. Principles of ergonomics and cognitive engineering were taken into account when designing the new conference hybrid control room for the Mochovce-3 and -4 reactor units. The sizes, propositions, shapes and disposition of the equipment at the control room have been created and verified by using virtual reality tools. (orig.)

A short-term operating room surgery scheduling problem integrating multiple nurses roster constraints.

Science.gov (United States)

Xiang, Wei; Yin, Jiao; Lim, Gino

2015-02-01

Operating room (OR) surgery scheduling determines the individual surgery's operation start time and assigns the required resources to each surgery over a schedule period, considering several constraints related to a complete surgery flow and the multiple resources involved. This task plays a decisive role in providing timely treatments for the patients while balancing hospital resource utilization. The originality of the present study is to integrate the surgery scheduling problem with real-life nurse roster constraints such as their role, specialty, qualification and availability. This article proposes a mathematical model and an ant colony optimization (ACO) approach to efficiently solve such surgery scheduling problems. A modified ACO algorithm with a two-level ant graph model is developed to solve such combinatorial optimization problems because of its computational complexity. The outer ant graph represents surgeries, while the inner graph is a dynamic resource graph. Three types of pheromones, i.e. sequence-related, surgery-related, and resource-related pheromone, fitting for a two-level model are defined. The iteration-best and feasible update strategy and local pheromone update rules are adopted to emphasize the information related to the good solution in makespan, and the balanced utilization of resources as well. The performance of the proposed ACO algorithm is then evaluated using the test cases from (1) the published literature data with complete nurse roster constraints, and 2) the real data collected from a hospital in China. The scheduling results using the proposed ACO approach are compared with the test case from both the literature and the real life hospital scheduling. Comparison results with the literature shows that the proposed ACO approach has (1) an 1.5-h reduction in end time; (2) a reduction in variation of resources' working time, i.e. 25% for ORs, 50% for nurses in shift 1 and 86% for nurses in shift 2; (3) an 0.25h reduction in

Shared-resource computing for small research labs.

Science.gov (United States)

Ackerman, M J

1982-04-01

A real time laboratory computer network is described. This network is composed of four real-time laboratory minicomputers located in each of four division laboratories and a larger minicomputer in a centrally located computer room. Off the shelf hardware and software were used with no customization. The network is configured for resource sharing using DECnet communications software and the RSX-11-M multi-user real-time operating system. The cost effectiveness of the shared resource network and multiple real-time processing using priority scheduling is discussed. Examples of utilization within a medical research department are given.

Modern control room for AHWR

International Nuclear Information System (INIS)

Verghese, Clement C.; Joseph, Jose; Biswas, B.B.; Patil, R.K.

2005-01-01

Advanced Heavy Water Reactor (AHWR) is a next generation nuclear power plant being developed by Bhabha Atomic Research Centre. A modern control room has been conceived for operation and monitoring of the plant in tune with the advanced features of the reactor. A state of the art C and I architecture based on extensive use of computers and networking has been conceived for this plant. This architecture enables the implementation of a fully computerised operator friendly control room with soft HMIs. Features of the modern control room and control room and concept of soft HMI based operator interfaces have been described in the paper. (author)

Room-temperature near-infrared electroluminescence from boron-diffused silicon pn junction diodes

Directory of Open Access Journals (Sweden)

Si eLi

2015-02-01

Full Text Available Silicon pn junction diodes with different doping concentrations were prepared by boron diffusion into Czochralski (CZ n-type silicon substrate. Their room-temperature near-infrared electroluminescence (EL was measured. In the EL spectra of the heavily boron doped diode, a luminescence peak at ~1.6 m (0.78 eV was observed besides the band-to-band line (~1.1eV under the condition of high current injection, while in that of the lightly boron doped diode only the band-to-band line was observed. The intensity of peak at 0.78 eV increases exponentially with current injection with no observable saturation at room temperature. Furthermore, no dislocations were found in the cross-sectional transmission electron microscopy image, and no dislocation-related luminescence was observed in the low-temperature photoluminescence spectra. We deduce the 0.78 eV emission originates from the irradiative recombination in the strain region of diodes caused by the diffusion of large number of boron atoms into silicon crystal lattice.

Leadership in the control room

International Nuclear Information System (INIS)

McDougall, S.J.

2006-01-01

This paper discusses the importance of leadership within the control rooms at nuclear power facilities. the leadership capability of control room staff has a significant influence over the improvement of human performance and the development of an 'event free' culture within the business. The development of leadership competency in the control room must be an important part of any nuclear power utility business improvement plan. (author)

209-E Building -- Response to ventilation failure evaluation

International Nuclear Information System (INIS)

Foust, D.J.

1998-01-01

This document provides an evaluation and recommendations for radiological workplace air monitoring and response to ventilation failure for the Critical Mass Laboratory, 209-E Building. The Critical Mass Laboratory, part of the 209-E Building, was designed to provide a heavily shielded room where plutonium and uranium liquid solutions could be brought into various critical configurations under readily controlled and monitored conditions. The facility is contained within a one-story L-shaped concrete block and reinforced concrete building. One wing houses offices, a control room, shops, and a common area while the other wing includes an equipment room, the change room, work areas, and the two-story Critical Assembly Room (CAR). Three of the rooms contain radiologically contaminated equipment and materials

Designing EvoRoom: An Immersive Simulation Environment for Collective Inquiry in Secondary Science

Science.gov (United States)

Lui, Michelle Mei Yee

This dissertation investigates the design of complex inquiry for co-located students to work as a knowledge community within a mixed-reality learning environment. It presents the design of an immersive simulation called EvoRoom and corresponding collective inquiry activities that allow students to explore concepts around topics of evolution and biodiversity in a Grade 11 Biology course. EvoRoom is a room-sized simulation of a rainforest, modeled after Borneo in Southeast Asia, where several projected displays are stitched together to form a large, animated simulation on each opposing wall of the room. This serves to create an immersive environment in which students work collaboratively as individuals, in small groups and a collective community to investigate science topics using the simulations as an evidentiary base. Researchers and a secondary science teacher co-designed a multi-week curriculum that prepared students with preliminary ideas and expertise, then provided them with guided activities within EvoRoom, supported by tablet-based software as well as larger visualizations of their collective progress. Designs encompassed the broader curriculum, as well as all EvoRoom materials (e.g., projected displays, student tablet interfaces, collective visualizations) and activity sequences. This thesis describes a series of three designs that were developed and enacted iteratively over two and a half years, presenting key features that enhanced students' experiences within the immersive environment, their interactions with peers, and their inquiry outcomes. Primary research questions are concerned with the nature of effective design for such activities and environments, and the kinds of interactions that are seen at the individual, collaborative and whole-class levels. The findings fall under one of three themes: 1) the physicality of the room, 2) the pedagogical script for student observation and reflection and collaboration, and 3) ways of including collective

Advantages and Disadvantages of Physiological Assessment For Next Generation Control Room Design

Energy Technology Data Exchange (ETDEWEB)

Tuan Q. Tran; Ronald L. Boring; Donald D. Dudenhoeffer; Bruce P Hallbert; M. David Keller; Tessa M. Anderson

2007-08-01

Abstract - We propose using non-obtrusive physiological assessment (e.g., eye tracking,) to assess human information processing errors (e.g., loss of vigilance) and limitations (e.g., workload) for advanced energy systems early in the design process. This physiological approach for assessing risk will circumvent many limitations of current risk methodologies such as subjective rating (e.g., rater’s biases) and performance modeling (e.g., risk assessment is scripted and is based upon the individual modeler’s judgment). Key uses will be to evaluate (early in the design process) novel control room equipment and configurations as well as newly developed automated systems that will inevitably place a high information load on operators. The physiological risk assessment tool will allow better precision in pinpointing problematic design issues and will provide a “real-time” assessment of risk. Furthermore, this physiological approach would extend the state-of-the-art of human reliability methods from a “static” measure to more “dynamic.” This paper will discuss a broad range of the current popular online performance gauges as well as its advantages and disadvantages for use in next generation control room.

Operating room manager game

NARCIS (Netherlands)

Hans, Elias W.; Nieberg, T.

2007-01-01

The operating room (OR) department of a hospital forms the heart of the organization, where the single largest cost is incurred. This document presents and reports on the “Operating Room Manager Game,” developed to give insight into managing a large hospital's OR department at various levels of

Overutilization and underutilization of operating rooms - insights from behavioral health care operations management.

Science.gov (United States)

Fügener, Andreas; Schiffels, Sebastian; Kolisch, Rainer

2017-03-01

The planning of surgery durations is crucial for efficient usage of operating theaters. Both planning too long and too short durations for surgeries lead to undesirable consequences, e.g. idle time, overtime, or rescheduling of surgeries. We define these consequences as operating room inefficiency. The overall objective of planning surgery durations is to minimize expected operating room inefficiency, since surgery durations are stochastic. While most health care studies assume economically rational behavior of decision makers, experimental studies have shown that decision makers often do not act according to economic incentives. Based on insights from health care operations management, medical decision making, behavioral operations management, as well as empirical observations, we derive hypotheses that surgeons' behavior deviates from economically rational behavior. To investigate this, we undertake an experimental study where experienced surgeons are asked to plan surgeries with uncertain durations. We discover systematic deviations from optimal decision making and offer behavioral explanations for the observed biases. Our research provides new insights to tackle a major problem in hospitals, i.e. low operating room utilization going along with staff overtime.

Implementation of the Resource Disincentive in 40 CFR part 191.14 (e) at the Waste Isolation Pilot Plant

International Nuclear Information System (INIS)

1993-06-01

In 1986, the US Department of Energy (DOE) Waste Isolation Pilot Plant (WIPP) Project Office (WPO) (DOE-WPO) prepared a strategy for complying with the Environmental Protection Agency's (EPA's) Standards for the management of transuranic (TRU) waste. Section 3.2.2.2 of the DOE's report addressed compliance with the Assurance Requirements found in 40 CFR section 191.14. One of the Assurance Requirements addresses the selection of repository sites that contain recoverable natural resources. This report documents that the site selection process for the WIPP facility did indeed comply with the natural resource disincentive requirement in 40 CFR section 191,14(e) at the time selected and therefore complies with the standard at this time. Thus, it shall be shown that it is reasonably certain that the WIPP site provides better overall protection than practical alternatives that were available when the site was selected. It is important to point out here, and it will be discussed later in the report, that the resource disincentive requirement is a preliminary siting criterion that requires further evaluation of sites that have resources (i.e, hydrocarbons, minerals and groundwater) in the vicinity or on the site. This further evaluation requires that for sites that do have resources, a qualitative determination must be made that the site will provide better overall protection than practical alternatives. The purpose of this report is not to provide a quantitative evaluation for selection of the WIPP site. A further discussion on the difference between the qualitative analysis required under 40 CFR section 191.14(e) and the quantitative analysis under other sections of 40 CFR 191 is provided in section 2.1 of this report

Leadership in the control room

Energy Technology Data Exchange (ETDEWEB)

McDougall, S.J. [Bruce Power, Bruce B Operations Div., Tiverton, Ontario (Canada)

2006-07-01

This paper discusses the importance of leadership within the control rooms at nuclear power facilities. the leadership capability of control room staff has a significant influence over the improvement of human performance and the development of an 'event free' culture within the business. The development of leadership competency in the control room must be an important part of any nuclear power utility business improvement plan. (author)

Recursos no ambiente familiar e dificuldades de aprendizagem na escola Home resources and school learning difficulties

Directory of Open Access Journals (Sweden)

Edna Maria Marturano

1999-08-01

Full Text Available Recursos do ambiente familiar, que favorecem o desempenho escolar, incluem materiais educacionais e envolvimento parental. Realizou-se um estudo com o objetivo de investigar esses recursos em uma amostra clínica de 100 crianças, encaminhadas por dificuldades na aprendizagem escolar. Os dados foram coletados durante entrevista com a mãe, por meio de um roteiro para sondagem de recursos e circunstâncias adversas. À criança era solicitado um texto a partir de um desenho. A análise estatística incluiu análise de regressão, correlação e comparação entre médias de subgrupos constituídos segundo idade, atraso escolar e desempenho na escrita. Os resultados indicaram que o nível de elaboração da escrita está positivamente associado à disponibilidade de livros e brinquedos, enquanto o atraso escolar está negativamente associado à organização das rotinas e à diversidade de atividades compartilhadas com os pais. Circunstâncias adversas têm associação positiva com atraso. Os resultados são discutidos quanto à sua aplicabilidade em programas de orientação psicopedagógica às famílias.Home resources which promote school achievement include educational materials and parent involvement with children's schooling. A study was performed with the aim of investigating these resources in a clinical sample of 100 children, who were referred for school learning problems. The data were collected with the mother, by means of a interview designed for the assessment of home resources and adversities. The child was asked to write a text from a drawing. Statistical analysis included regression analysis, correlation and comparisons between groups formed by age, school backwardness, and writing performance. Results indicated that writing level is positively related with the provision of books and toys, while school backwardness is negatively related with regularity in the use of time and with diversity of activities shared with parents

Families of children with special educational needs resources and needs support

Directory of Open Access Journals (Sweden)

Danielli Silva Gualda

2013-06-01

Full Text Available The goal of this research was to investigate what are the resources and needs of parents of preschool children with special educational needs. The participants were eleven parents of children with special educational needs included in pre-elementary school. Most parents had purchasing power medium to medium low. To meet the objectives, parents filled in the “Inventory of Home Environment Resources - RAF” and “Questionnaire on the needs of families - QNF. The results enabled the RAF to note that this study the majority of children with special educational needs and has a stimulating home environment, whereas the mothers accompanied their children in school affairs and the maintenance of a routine to perform activities, and receive care through resource rooms (41.6% and in the care of APAE (25.0%. the data obtained by QNF parents need help to: (a to obtain more information about services and supports that your child may benefit in the future, (b meet regularly with appropriate persons, as professionals, to talk on the child’s disability, (c explain the child’s other children, friends and neighbors, (d find social support services and educational for the child, (e pay expenses and (f to discuss problems and find solutions.

Operating room fires in periocular surgery.

Science.gov (United States)

Connor, Michael A; Menke, Anne M; Vrcek, Ivan; Shore, John W

2018-06-01

A survey of ophthalmic plastic and reconstructive surgeons as well as seven-year data regarding claims made to the Ophthalmic Mutual Insurance Company (OMIC) is used to discuss operating room fires in periocular surgery. A retrospective review of all closed claim operating room fires submitted to OMIC was performed. A survey soliciting personal experiences with operating room fires was distributed to all American Society of Oculoplastic and Reconstructive Surgeons. Over the last 2 decades, OMIC managed 7 lawsuits resulting from an operating room fire during periocular surgery. The mean settlement per lawsuit was $145,285 (range $10,000-474,994). All six patients suffered burns to the face, and three required admission to a burn unit. One hundred and sixty-eight surgeons participated in the online survey. Approximately 44% of survey respondents have experienced at least one operating room fire. Supplemental oxygen was administered in 88% of these cases. Most surgical fires reported occurred in a hospital-based operating room (59%) under monitored anesthesia care (79%). Monopolar cautery (41%) and thermal, high-temperature cautery (41%) were most commonly reported as the inciting agents. Almost half of the patients involved in a surgical fire experienced a complication from the fire (48%). Sixty-nine percent of hospital operating rooms and 66% of ambulatory surgery centers maintain an operating room fire prevention policy. An intraoperative fire can be costly for both the patient and the surgeon. Ophthalmic surgeons operate in an oxygen rich and therefore flammable environment. Proactive measures can be undertaken to reduce the incidence of surgical fires periocular surgery; however, a fire can occur at any time and the entire operating room team must be constantly vigilant to prevent and manage operating room fires.

[The hybrid operating room. Home of high-end intraoperative imaging].

Science.gov (United States)

Gebhard, F; Riepl, C; Richter, P; Liebold, A; Gorki, H; Wirtz, R; König, R; Wilde, F; Schramm, A; Kraus, M

2012-02-01

A hybrid operating room must serve the medical needs of different highly specialized disciplines. It integrates interventional techniques for cardiovascular procedures and allows operations in the field of orthopaedic surgery, neurosurgery and maxillofacial surgery. The integration of all steps such as planning, documentation and the procedure itself saves time and precious resources. The best available imaging devices and user interfaces reduce the need for extensive personnel in the OR and facilitate new minimally invasive procedures. The immediate possibility of postoperative control images in CT-like quality enables the surgeon to react to problems during the same procedure without the need for later revision.

32 CFR 518.9 - Reading room.

Science.gov (United States)

2010-07-01

... RELATIONS THE FREEDOM OF INFORMATION ACT PROGRAM FOIA Reading Rooms § 518.9 Reading room. (a) Reading room... clearly unwarranted invasions of privacy, or competitive harm to business submitters. In appropriate cases... information concerning munitions, equipment, systems, and intelligence activities. (4) (a)(2)(D) records...

7 CFR 58.312 - Churn rooms.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Churn rooms. 58.312 Section 58.312 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards....312 Churn rooms. Churn rooms in addition to proper construction and sanitation shall be so equipped...

Control room habitability Analysis and Testing for Wolsong Unit 1

Energy Technology Data Exchange (ETDEWEB)

Lee, J. B. [KHNP Central Research Institute, Daejeon (Korea, Republic of)

2013-05-15

In response to this recommendation, KHNP has established CRH program and performed tracer gas in leakage tests. These activities are described herein including the emergency ventilation system analysis, acceptance criteria calculation for the test and Control Room Envelope (CRE) discrimination, and the results of the tracer gas tests are presented. CRH analysis including unfiltered in leakage tests according to the methodology in ASTM E741 was performed for Wolsong Unit 1. The results show that the integrity of the control room of Wolsong Unit 1 is in good condition to maintain the reactor in a safe condition under accident conditions, which complies with the US NRC regulatory guides 1.78, 1.196 and 1.197.

Manufacturing of NAA laboratory clean room

International Nuclear Information System (INIS)

Suwoto; Hasibuan, Djaruddin

2001-01-01

The ''NAA laboratory clean room'' has been built in the Reactor Serba Guna G.A. Siwabessy building. The erection of ''AAN laboratory clean room'' doing by started of preparation of the ''manufacturing procedure'' refer to ''Design and manufacturing neutron activation analysis clean room laboratory''. Manufacturing process and erection doing refer to procedures makes. By providing of the ''AAN laboratory clean room'' can be cocluded that the research activity and the user sevises in P2TRR well meet to be done

Students' Perspectives on YouTube Video Usage as an E-Resource in the University Classroom

Science.gov (United States)

Jackman, W. Marc; Roberts, Patricia

2014-01-01

This study examined the perspectives of 70 prospective teachers about the use of YouTube videos as e-resources to supplement psychology lectures at a university in Trinidad & Tobago. A questionnaire designed for the study was used to collect both quantitative and qualitative data. The quantitative analysis included frequency distribution,…

Auditory modelling for assessing room acoustics

NARCIS (Netherlands)

Van Dorp Schuitman, J.

2011-01-01

The acoustics of a concert hall, or any other room, are generally assessed by measuring room impulse responses for one or multiple source and receiver location(s). From these responses, objective parameters can be determined that should be related to various perceptual attributes of room acoustics.

Towards an Einstein–Podolsky–Rosen paradox between two macroscopic atomic ensembles at room temperature

International Nuclear Information System (INIS)

He, Q Y; Reid, M D

2013-01-01

Experiments have reported the entanglement of two spatially separated macroscopic atomic ensembles at room temperature (Krauter et al 2011 Phys. Rev. Lett. 107 080503; Julsgaard et al 2001 Nature 413 400). We show how an Einstein–Podolsky–Rosen (EPR) paradox is realizable with this experiment. Our proposed test involves violation of an inferred Heisenberg uncertainty principle, which is a sufficient condition for an EPR paradox. This is a stronger test of nonlocality than entanglement. Our proposal would enable the first definitive confirmation of quantum EPR paradox correlations between two macroscopic objects at room temperature. This is a necessary intermediate step towards a nonlocal experiment with causal measurement separations. As well as having fundamental significance, the realization of an atomic EPR paradox could provide a resource for novel applications in quantum technology. (paper)

Towards an Einstein-Podolsky-Rosen paradox between two macroscopic atomic ensembles at room temperature

Science.gov (United States)

He, Q. Y.; Reid, M. D.

2013-06-01

Experiments have reported the entanglement of two spatially separated macroscopic atomic ensembles at room temperature (Krauter et al 2011 Phys. Rev. Lett. 107 080503; Julsgaard et al 2001 Nature 413 400). We show how an Einstein-Podolsky-Rosen (EPR) paradox is realizable with this experiment. Our proposed test involves violation of an inferred Heisenberg uncertainty principle, which is a sufficient condition for an EPR paradox. This is a stronger test of nonlocality than entanglement. Our proposal would enable the first definitive confirmation of quantum EPR paradox correlations between two macroscopic objects at room temperature. This is a necessary intermediate step towards a nonlocal experiment with causal measurement separations. As well as having fundamental significance, the realization of an atomic EPR paradox could provide a resource for novel applications in quantum technology.

Cultural differences in room size perception.

Science.gov (United States)

Saulton, Aurelie; Bülthoff, Heinrich H; de la Rosa, Stephan; Dodds, Trevor J

2017-01-01

Cultural differences in spatial perception have been little investigated, which gives rise to the impression that spatial cognitive processes might be universal. Contrary to this idea, we demonstrate cultural differences in spatial volume perception of computer generated rooms between Germans and South Koreans. We used a psychophysical task in which participants had to judge whether a rectangular room was larger or smaller than a square room of reference. We systematically varied the room rectangularity (depth to width aspect ratio) and the viewpoint (middle of the short wall vs. long wall) from which the room was viewed. South Koreans were significantly less biased by room rectangularity and viewpoint than their German counterparts. These results are in line with previous notions of general cognitive processing strategies being more context dependent in East Asian societies than Western ones. We point to the necessity of considering culturally-specific cognitive processing strategies in visual spatial cognition research.

Cultural differences in room size perception.

Directory of Open Access Journals (Sweden)

Aurelie Saulton

Full Text Available Cultural differences in spatial perception have been little investigated, which gives rise to the impression that spatial cognitive processes might be universal. Contrary to this idea, we demonstrate cultural differences in spatial volume perception of computer generated rooms between Germans and South Koreans. We used a psychophysical task in which participants had to judge whether a rectangular room was larger or smaller than a square room of reference. We systematically varied the room rectangularity (depth to width aspect ratio and the viewpoint (middle of the short wall vs. long wall from which the room was viewed. South Koreans were significantly less biased by room rectangularity and viewpoint than their German counterparts. These results are in line with previous notions of general cognitive processing strategies being more context dependent in East Asian societies than Western ones. We point to the necessity of considering culturally-specific cognitive processing strategies in visual spatial cognition research.

Public census data on CD-ROM at Lawrence Berkeley Laboratory

Energy Technology Data Exchange (ETDEWEB)

Merrill, D.W.

1992-10-01

The Comprehensive Epidemiologic Data Resource (CEDR) and Populations at Risk to Environmental Pollution (PAREP) projects, of the Information and Computing Sciences Division (ICSD) at Lawrence Berkeley Laboratory (LBL), are using public socio-economic and geographic data files which are available to CEDR and PAREP collaborators via LBL's computing network. At this time 70 CD-ROM diskettes (approximately 36 gigabytes) are on line via the Unix file server cedrcd. lbl. gov. Most of the files are from the US Bureau of the Census, and most pertain to the 1990 Census of Population and Housing. All the CD-ROM diskettes contain documentation in the form of ASCII text files. Printed documentation for most files is available for inspection at University of California Data and Technical Assistance (UC DATA), or the UC Documents Library. Many of the CD-ROM diskettes distributed by the Census Bureau contain software for PC compatible computers, for easily accessing the data. Shared access to the data is maintained through a collaboration among the CEDR and PAREP projects at LBL, and UC DATA, and the UC Documents Library. Via the Sun Network File System (NFS), these data can be exported to Internet computers for direct access by the user's application program(s).

Public census data on CD-ROM at Lawrence Berkeley Laboratory

Energy Technology Data Exchange (ETDEWEB)

Merrill, D.W.

1992-10-01

The Comprehensive Epidemiologic Data Resource (CEDR) and Populations at Risk to Environmental Pollution (PAREP) projects, of the Information and Computing Sciences Division (ICSD) at Lawrence Berkeley Laboratory (LBL), are using public socio-economic and geographic data files which are available to CEDR and PAREP collaborators via LBL`s computing network. At this time 70 CD-ROM diskettes (approximately 36 gigabytes) are on line via the Unix file server cedrcd. lbl. gov. Most of the files are from the US Bureau of the Census, and most pertain to the 1990 Census of Population and Housing. All the CD-ROM diskettes contain documentation in the form of ASCII text files. Printed documentation for most files is available for inspection at University of California Data and Technical Assistance (UC DATA), or the UC Documents Library. Many of the CD-ROM diskettes distributed by the Census Bureau contain software for PC compatible computers, for easily accessing the data. Shared access to the data is maintained through a collaboration among the CEDR and PAREP projects at LBL, and UC DATA, and the UC Documents Library. Via the Sun Network File System (NFS), these data can be exported to Internet computers for direct access by the user`s application program(s).

A room of one's own--Being cared for in a hospital with a single-bed room design.

Science.gov (United States)

Persson, Eva; Anderberg, Patrice; Ekwall, Anna Kristensson

2015-06-01

To illuminate patients' experiences of being hospitalised in a hospital with a single-bed room design. Many patients seem to prefer single-bed hospital rooms. However, studies have also shown that patients do see the advantages of multiple-bed rooms. Interviews were conducted with 16 inpatients from a surgical ward in a hospital building with a single-bed room design. A hermeneutical-phenomenological approach guided by van Manen's four life-world existentials was used to analyse the interviews. The essential meaning was that patients felt secure because they could create a personal environment without disruptive elements. The room was private, and this implied feelings of homeliness, which allowed patients to focus on themselves and was thought to facilitate the recovery process. The patients preferred staying in their room, and the relationship with the personnel was central. Feelings of loneliness and isolation could occur and could be frightening. Being hospitalised in a single-bed room meant balancing between feeling secure and feeling insecure. The following four themes emerged: A homely environment, The need for company and security, Time as unpredictable and involving waiting and Focus on healing the body. Patients experienced that a single-bed room allowed them to focus on their recovery, have visitors without disturbing others and create a feeling of homeliness. However, mobilisation is not a natural part of the recovery process when patients have all they need in their rooms. The patients' need for social interaction and confirmation was not satisfied without effort and planning on the part of staff. © 2014 Nordic College of Caring Science.

Experience in development and implementation of Control Room continuing training programme at Ignalina NPP

International Nuclear Information System (INIS)

Peradze, K.

2002-01-01

Based on the same SAT principles each NPP (or operating organisation) goes by its own way, which is defined by available resources, assistance, NPP operational conditions, including policy, economics and public opinion. There were several groups of factors, which are very important to provide quality of training- Time, Human Resources and material resources. We pay especial attention to simulator training. In different conditions personnel behaviour is defined by knowledge, rule or skills. It is very difficult to develop unknown to personnel scenarios. But sometimes- real events not described in plant procedures take place at Nuclear Power Plants. Therefore during NPP events analysis we pay a especial attention searching for situation when knowledge or rule defines personnel behaviour. To provide analysis and statistics of Control Room Personnel training at INPP simulator we developed 'INPP events computer data base'. (author)

Software quality assurance and software safety in the Biomed Control System

International Nuclear Information System (INIS)

Singh, R.P.; Chu, W.T.; Ludewigt, B.A.; Marks, K.M.; Nyman, M.A.; Renner, T.R.; Stradtner, R.

1989-01-01

The Biomed Control System is a hardware/software system used for the delivery, measurement and monitoring of heavy-ion beams in the patient treatment and biology experiment rooms in the Bevalac at the Lawrence Berkeley Laboratory (LBL). This paper describes some aspects of this system including historical background philosophy, configuration management, hardware features that facilitate software testing, software testing procedures, the release of new software quality assurance, safety and operator monitoring. 3 refs

ALICE’s new meeting room

CERN Multimedia

2009-01-01

There’s no reason to be late for a meeting in Wonderland (Point 2) anymore as ALICE gets a brand new conference room and a ‘clean up’. The new ALICE conference room.You won’t find Building 3294 on the CERN map yet, but it is already being used. If you follow the white rabbit just inside the entrance at point 2, you will find a new conference room and office space for 12 people. "Previously at Point 2 we’ve had very little office space at all. Our old conference room was inside the main building, SX2, but it was cramped and extremely noisy," explained Frank Cliff from ALICE. "As soon as they turned on the overhead cranes you could barely hear yourself think!" The plans for the new building were drawn up by the Civil Engineering Group, and construction started in August last year. The building was completed and already in use before Christmas. The 109 square metre conference room can fit up to 60 people and is fully equipped...

Expert System and Heuristics Algorithm for Cloud Resource Scheduling

Directory of Open Access Journals (Sweden)

Mamatha E

2017-03-01

Full Text Available Rule-based scheduling algorithms have been widely used on cloud computing systems and there is still plenty of room to improve their performance. This paper proposes to develop an expert system to allocate resources in cloud by using Rule based Algorithm, thereby measuring the performance of the system by letting the system adapt new rules based on the feedback. Here performance of the action helps to make better allocation of the resources to improve quality of services, scalability and flexibility. The performance measure is based on how the allocation of the resources is dynamically optimized and how the resources are utilized properly. It aims to maximize the utilization of the resources. The data and resource are given to the algorithm which allocates the data to resources and an output is obtained based on the action occurred. Once the action is completed, the performance of every action is measured that contains how the resources are allocated and how efficiently it worked. In addition to performance, resource allocation in cloud environment is also considered.

Detection of Ebola Virus RNA through Aerosol Sampling of Animal Biosafety Level 4 Rooms Housing Challenged Nonhuman Primates

Science.gov (United States)

2016-08-02

Rooms Housing Challenged Nonhuman Primates 10 11 12 13 14 15 David E. Harbourt1*, Sara C. Johnston1, James Pettitt2, Travis K. Warren1 and...Sampling of ABSL-4 Rooms Housing Challenged Nonhuman 10 Primates for publication in an edition of The Journal of Infectious Disease. This 11 manuscript...embedded in the texts. This is the first report demonstrating detection of Ebola virus 17 RNA from animal rooms housing infected nonhuman primates and

Resource Structuring and Ambidexterity

DEFF Research Database (Denmark)

Ma, Yucheng; Li, Peter Ping

-shaped effect on organizational ambidexterity in new ventures. Further, because of the traditional culture and economic transition characteristics, new ventures actively leverage managerial ties as key social relations to obtain special resources or nurture business transactions. We propose that ties with other......Focusing on how resource structuring mechanisms and managerial ties influence organizational ambidexterity of new ventures in emerging economy, this study explores the effects of resource structuring mechanisms (i.e., resource acquiring and resource accumulating) on organizational ambidexterity....... It further examines the moderating effects of managerial ties, (i.e., ties with other firms and ties with the government) on the above relationships. Survey data from China¡¯s 202 new ventures demonstrates that the resource acquiring has an inverted U-shaped effect whereas the resource accumulating has a U...

An Optimisation Approach for Room Acoustics Design

DEFF Research Database (Denmark)

Holm-Jørgensen, Kristian; Kirkegaard, Poul Henning; Andersen, Lars

2005-01-01

This paper discuss on a conceptual level the value of optimisation techniques in architectural acoustics room design from a practical point of view. It is chosen to optimise one objective room acoustics design criterium estimated from the sound field inside the room. The sound field is modeled...... using the boundary element method where absorption is incorporated. An example is given where the geometry of a room is defined by four design modes. The room geometry is optimised to get a uniform sound pressure....

Hybrid control rooms: the effects of introducing new technology into existing control rooms

International Nuclear Information System (INIS)

Morisseau, Dolores S.

2001-02-01

The goal of this part of the Hybrid Control Room Project is to gain a perspective on the issues and problems that are an integral part of introducing new technology, automated systems, or support systems into nuclear power plant (NPP) control rooms, particularly when they are introduced on a system-by-system basis. For purposes of this project, hybrid control rooms are defined as those into which new technology, such as digital and computer-based controls are gradually incorporated as opposed to those that are completely, or nearly completely, refitted with new technology. Although the focus of this project is the introduction of computer based, digital systems into NPP control rooms, it is not possible to exclude the effects throughout the process that are inevitable when new technology is introduced anywhere in complex process control systems. Thus, this document examines the effects of such changes within the context of the organisation in which they occur, including the management of change, work procedures and work methods, communications and crew interaction, training, and the interdependent functions in the operational context. (Author)

Comparisons of Mathematics Intervention Effects in Resource and Inclusive Classrooms

Science.gov (United States)

Bottge, Brian A.; Cohen, Allan S.; Choi, Hye-Jeong

2018-01-01

In this article, we describe results of a reanalysis of two randomized studies that tested the effects of enhanced anchored instruction (EAI) on the fractions computation performance of students in special education resource rooms and inclusive mathematics classrooms. Latent class analysis and latent transition analysis classified students…

Shielded room measurements, Final report

Energy Technology Data Exchange (ETDEWEB)

Stanton, J.S.

1949-02-22

The attenuation of electro-statically and electro-magnetically shielded rooms in the ``E,`` ``R,`` ``I,`` and ``T`` Buildings was measured so that corrective measure could be taken if the attenuation was found to be low. If remedial measures could not be taken, the shortcomings of the rooms would be known. Also, the men making the measurements should oversee construction and correct errors at the time. The work was performed by measuring the attenuation at spot frequencies over the range of from 150 kilocycles to 1280 megacycles with suitable equipment mounted in small rubber-tried trucks. The attenuation was determined by ``before and after`` shielding and/or ``door open and door closed`` measurements after installation of copper shielding. In general, attenuation in the frequency range of approximately 10 to 150 mc. was good and was of the order expected. At frequencies in the range of 150 mc. to 1280 mc., the attenuation curve was more erratic; that is, at certain frequencies a severe loss of attenuation was noted, while at others, the attenuation was very good. This was mainly due to poor or faulty seals around doors and pass windows. These poor seals existed in the ``T,`` ``E,`` and ``I`` Buildings because the doors were fitted improperly and somewhat inferior material was used. By experience from these difficulties, both causes were corrected in the ``R`` Building, which resulted in the improvement of the very high frequency (v.h.f.) range in this building. In some specific cases, however, the results were about the same. For the range of frequencies below approximately 10 mc., the attenuation, in almost all cases, gradually decreased as the frequency decreased and reached a minimum at .3 to 1.0 mc. This loss of attenuation was attributed to multiple grounding caused by moisture in the insulating timbers and will gradually decrease as the wood dries out.

Start time delays in operating room: Different perspectives

Directory of Open Access Journals (Sweden)

Babita Gupta

2011-01-01

Full Text Available Background: Healthcare expenditure is a serious concern, with escalating costs failing to meet the expectations of quality care. The treatment capacities are limited in a hospital setting and the operating rooms (ORs. Their optimal utilization is vital in efficient hospital management. Starting late means considerable wait time for staff, patients and waste of resources. We planned an audit to assess different perspectives of the residents in surgical specialities and anesthesia and OR staff nurses so as to know the causative factors of operative delay. This can help develop a practical model to decrease start time delays in operating room (ORs. Aims: An audit to assess different perspectives of the Operating room (OR staff with respect to the varied causative factors of operative delay in the OR. To aid in the development of a practical model to decrease start time delays in ORs and facilitate on-time starts at Jai Prakash Narayan Apex Trauma centre (JPNATC, All India Institute of Medical Sciences (AIIMS, New Delhi. Methods: We prepared a questionnaire seeking the five main reasons of delay as per their perspective. Results: The available data was analysed. Analysis of the data demonstrated the common causative factors in start time operative delays as: a lack of proper planning, deficiencies in team work, communication gap and limited availability of trained supporting staff. Conclusions: The preparation of the equipment and required material for the OR cases must be done well in advance. Utilization of newer technology enables timely booking and scheduling of cases. Improved inter-departmental coordination and compliance with preanesthetic instructions needs to be ensured. It is essential that the anesthesiologists perform their work promptly, well in time . and supervise the proceedings as the OR manager. This audit is a step forward in defining the need of effective OR planning for continuous quality improvement.

The interaction between room and musical instruments studied by multi-channel auralization

DEFF Research Database (Denmark)

Rindel, Jens Holger; Otondo, Felipe

2005-01-01

in the anechoic recording. With this technique the variations in sound radiation from the musical instrument during the performance e.g. due to changes in level or movements can be reproduced with the influence of the surrounding room surfaces. Examples include a grand piano and a clarinet.......The directivity of musical instruments is very complicated and typically changes from one tone to the next. So, instead of measuring the average directivity, a multi-channel auralization method has been developed, which allows a highly accurate and realistic sounding auralization of musical...... instruments in rooms. Anechoic recordings have been made with 5 and 13 evenly distributed microphones around the musical instrument. The reproduction is made with a room acoustics simulation software using a compound source, which is in fact a number of highly directive sources, one for each of the channels...

The ePortfolio as an educational resource and its impact on job search

Directory of Open Access Journals (Sweden)

Monika Ciesielkiewicz

2015-09-01

Full Text Available This paper intends to make evident that the ePortfolio is an effective and cuttingedge learning and evaluation tool, as well as a multimedia curriculum vitae that can be sent out to future employers. It can be used to present, document, reflect on, and promote students’ skills, credentials, certificates and diverse formal and informal experiences in a structured, wellorganized and marketable way. Different types and parts of ePortfolio will be explained in this paper and it will be demonstrated that ePortfolio teaches a ranges of strategies that facilitates learning, as well as the acquisition of skills needed in a workplace. Besides, real examples of ePortfolio, both american and spanish version, developed by students in both countries will be presented. Finally, the results of a survey carried out among fifty two human resources directors will be analyzed. This paper will demonstrate that the electronic portfolio can be considered a very useful and effective job search tool that can count with a significant approval in the business world.

Birth room images

DEFF Research Database (Denmark)

Bowden, Calida; Sheehan, Athena; Foureur, Maralyn Jean

2016-01-01

Objective: this study examined images of birth rooms in developed countries to analyse the messages and visual discourse being communicated through images. Design: a small qualitative study using Kress and van Leeuwen's (2006) social semiotic theoretical framework for image analysis, a form...... and implications for practice: as images on the Internet inform and persuade society about stereotypical behaviours, the trends of our time and sociocultural norms, it is important to recognise images of the technological birth room on the Internet may be influential in dictating women's attitudes, choices...

Creating Engaging Escape Rooms for the Classroom

Science.gov (United States)

Nicholson, Scott

2018-01-01

Escape rooms are "live-action team-based games where players discover clues, solve puzzles, and accomplish tasks in one or more rooms in order to accomplish a specific goal (usually escaping from the room) in a limited amount of time." Escape Rooms are one type of Escape Game, which are narrative-based challenges that use puzzles, tasks,…

Hospital Patient Room Design: The Issues Facing 23 Occupational Groups Who Work in Medical/Surgical Patient Rooms.

Science.gov (United States)

Lavender, Steven A; Sommerich, Carolyn M; Patterson, Emily S; Sanders, Elizabeth B-N; Evans, Kevin D; Park, Sanghyun; Umar, Radin Zaid Radin; Li, Jing

2015-01-01

The aim of this study was to learn from a wide range of hospital staff members about how the design of the patient room in which they work adversely affects their ergonomics or hinders their job performance. In addition to providing a healing space for patients, hospital patient rooms need to serve as functional workplaces for the people who provide clinical care, to clean, or to maintain room functions. Therefore, from a design perspective, it is important to understand the needs of all the users of hospital patient rooms with regard to room design. One hundred forty-seven people, representing 23 different occupational stakeholder groups, participated in either focus groups or interviews in which they were asked to identify room design issues that affect the performance of their work tasks. Key issues shared across multiple stakeholder groups included an inability to have eye contact with the patient when entering the room, inadequate space around the bed for the equipment used by stakeholders, the physical demands experienced as stakeholders move furnishings to accomplish their activities or access equipment, and a lack of available horizontal surfaces. Unique issues were also identified for a number of stakeholder groups. There are a number of issues that should be addressed in the next generation of hospital patient rooms, or when refurbishing existing facilities, so that all occupational stakeholder groups can work effectively, efficiently, and without undue physical stress. © The Author(s) 2015.

E-serials cataloging access to continuing and integrating resources via the catalog and the web

CERN Document Server

Cole, Jim

2014-01-01

This comprehensive guide examines the state of electronic serials cataloging with special attention paid to online capacities. E-Serials Cataloging: Access to Continuing and Integrating Resources via the Catalog and the Web presents a review of the e-serials cataloging methods of the 1990s and discusses the international standards (ISSN, ISBD[ER], AACR2) that are applicable. It puts the concept of online accessibility into historical perspective and offers a look at current applications to consider. Practicing librarians, catalogers and administrators of technical services, cataloging and serv

In the LEAR control room

CERN Multimedia

CERN PhotoLab

1983-01-01

View into the control room of the Low Energy Antiproton Ring (LEAR). Edgar Asseo (sitting) and Dieter Möhl and Georges Carron reflecting upon some beam dynamics (or hardware?) problem. Vassilis Agoritsas, in the background, leaning over a plan or a keyboard. LEAR in its early years (1982 to about 1990) was run from this local control room in building 363 close to the end of the PS South Hall, where the ring was installed. Later-on the operation was surveyed from the PS main control room.

Room temperature ammonia and VOC sensing properties of CuO nanorods

International Nuclear Information System (INIS)

Bhuvaneshwari, S.; Gopalakrishnan, N.

2016-01-01

Here, we report a NH 3 and Volatile Organic Compounds (VOCs) sensing prototype of CuO nanorods with peculiar sensing characteristics at room temperature. High quality polycrystalline nanorods were synthesized by a low temperature hydrothermal method. The rods are well oriented with an aspect ratio of 5.71. Luminescence spectrum of CuO nanorods exhibited a strong UV-emission around 415 nm (2.98 eV) which arises from the electron-hole recombination phenomenon. The absence of further deep level emissions establishes the lack of defects such as oxygen vacancies and Cu interstitials. At room temperature, the sensor response was recorded over a range of gas concentrations from 100-600 ppm of ammonia, ethanol and methanol. The sensor response showed power law dependence with the gas concentration. This low temperature sensing can be validated by the lower value of calculated activation energy of 1.65 eV observed from the temperature dependent conductivity measurement.

Room temperature ammonia and VOC sensing properties of CuO nanorods

Science.gov (United States)

Bhuvaneshwari, S.; Gopalakrishnan, N.

2016-05-01

Here, we report a NH3 and Volatile Organic Compounds (VOCs) sensing prototype of CuO nanorods with peculiar sensing characteristics at room temperature. High quality polycrystalline nanorods were synthesized by a low temperature hydrothermal method. The rods are well oriented with an aspect ratio of 5.71. Luminescence spectrum of CuO nanorods exhibited a strong UV-emission around 415 nm (2.98 eV) which arises from the electron-hole recombination phenomenon. The absence of further deep level emissions establishes the lack of defects such as oxygen vacancies and Cu interstitials. At room temperature, the sensor response was recorded over a range of gas concentrations from 100-600 ppm of ammonia, ethanol and methanol. The sensor response showed power law dependence with the gas concentration. This low temperature sensing can be validated by the lower value of calculated activation energy of 1.65 eV observed from the temperature dependent conductivity measurement.

Room temperature ammonia and VOC sensing properties of CuO nanorods

Energy Technology Data Exchange (ETDEWEB)

Bhuvaneshwari, S.; Gopalakrishnan, N., E-mail: ngk@nitt.edu [Thin film laboratory, National Institute of Technology, Tiruchirappalli-620015 (India)

2016-05-23

Here, we report a NH{sub 3} and Volatile Organic Compounds (VOCs) sensing prototype of CuO nanorods with peculiar sensing characteristics at room temperature. High quality polycrystalline nanorods were synthesized by a low temperature hydrothermal method. The rods are well oriented with an aspect ratio of 5.71. Luminescence spectrum of CuO nanorods exhibited a strong UV-emission around 415 nm (2.98 eV) which arises from the electron-hole recombination phenomenon. The absence of further deep level emissions establishes the lack of defects such as oxygen vacancies and Cu interstitials. At room temperature, the sensor response was recorded over a range of gas concentrations from 100-600 ppm of ammonia, ethanol and methanol. The sensor response showed power law dependence with the gas concentration. This low temperature sensing can be validated by the lower value of calculated activation energy of 1.65 eV observed from the temperature dependent conductivity measurement.

Room-Temperature Synthesis of Transition Metal Clusters and Main Group Polycations from Ionic Liquids

OpenAIRE

Ahmed, Ejaz

2011-01-01

Main group polycations and transition metal clusters had traditionally been synthesized via high-temperature routes by performing reactions in melts or by CTR, at room-temperature or lower temperature by using so-called superacid solvents, and at room-temperature in benzene–GaX3 media. Considering the major problems associated with higher temperature routes (e.g. long annealing time, risk of product decomposition, and low yield) and taking into account the toxicity of benzene and liquid SO2 i...

[Management for the operating room].

Science.gov (United States)

Tschudi, O; Schüpfer, G

2015-03-01

Business companies, which in the current times also includes hospitals, must create customer benefits and as a prerequisite for this must sustainably generate profits. Management in the world of business means the formation and directing of a company or parts of a company on a permanent basis, whereby management in this context is not exercising power but function. This concept of management is exemplary developed in this article for the important services sector of the operating room (OR) and individual functions, such as resource control, capacity planning and materials administration are presented in detail. Some OR-specific management challenges are worked out. From this it becomes clear that the economic logic of the most efficient implementation possible is not a contradiction of medical ethics, enabling the most effective treatment possible for patients while safeguarding the highest possible levels of safety and quality. The article aims to build a bridge for medical specialists to the language and world of commerce, emphasizing the profession-based competence and hopefully to arouse interest to go into more detail.

The Potential of eLearning in the Spatial Information Sciences: a resource for Continuing Professional Development.

OpenAIRE

Mooney, Kevin; Martin, Audrey

2004-01-01

National mapping agencies have at their disposal a number of resources for the continuing professional development of their staff. These range from attendance at full-time University programmes to short in-house tutorials and workshops. The Dublin Institute of Technology has recently developed an eLearning course in ‘Co-ordinate reference systems for spatial information’ and piloted it with staff of Ordnance Survey Ireland and the Department of Lands and Surveys, Nicosia, Cyprus. This paper e...

Assessment of control room habitability and unfiltered air inleakage test of the OPR 1000 NPP

International Nuclear Information System (INIS)

Song, Dong Soo; Lee, Jong Beom; Ha, Sang Jun; Huh, Seong Cheol

2015-01-01

The assessment of control room habitability for Hanbit unit 5 was performed based on GL 2003-01 and Regulatory Guide 1.197. The integrated control room envelope (CRE) test was performed utilizing ASTM E741. Four tests were performed using each of the control room HVAC subtrains. The control room heating, ventilating, and air conditioning (HVAC) system lineup of pressurization mode test was based upon a lineup that encompassed the design basis radiological analyses. The other control room HVAC system lineup of isolation mode test was based on an operation mode that considers toxic gas. The measured inleakage for the isolation test mode remains within the toxicity limit. Radiation effect analysis showed that the measured inleakage satisfied the regulatory criteria, and the inleakage would not result in control room operator dose exceeding 50 mSv whole body and 500 mSv thyroid except train A pressurization test mode. The thyroid dose due to maximum measured unfiltered inleakage of 8976 lpm for train A is corresponding to 700 mSv. Modifications to the CRE boundary and control room HVAC system should be done to demonstrate that the measured unfiltered inleakage for train A pressurization test mode is bounded by the regulatory criteria assumed in the design basis radiological analyses. (author)

Heavy metal ternary halides for room-temperature x-ray and gamma-ray detection

Science.gov (United States)

Liu, Zhifu; Peters, John A.; Stoumpos, Constantinos C.; Sebastian, Maria; Wessels, Bruce W.; Im, Jino; Freeman, Arthur J.; Kanatzidis, Mercouri G.

2013-09-01

We report our recent progress on wide bandgap ternary halide compounds CsPbBr3 and CsPbCl3 for room temperature x-ray and gamma-ray detectors. Their bandgaps are measured to be 2.24 eV and 2.86 eV, respectively. The measured mobility-lifetime products of CsPbBr3 are 1.7×10-3, 1.3×10-3 cm2/V, for electron and hole carriers, respectively, comparable to those of CdTe. We measured the room temperature spectral response of CsPbBr3 sample to Ag x-ray radiation. It has a well-resolved spectral response to the 22.4 keV Kα radiation peak and detector efficiency comparable to that of CdZnTe detector at 295 K.

Developing an e-learning resource for nurse airway assistants in the emergency department.

Science.gov (United States)

Hersey, Peter; McAleer, Sean

2017-02-23

The aims of this project were to determine the required competencies for a nurse in the emergency department assisting with a rapid sequence induction of anaesthesia (RSI), and to produce a relevant e-learning resource. A three-round multidisciplinary Delphi process produced the following competencies: ability to describe the steps and sequence of events of an RSI, familiarity with the equipment used during an RSI, ability to recognise and help manage problems occurring during an RSI, ability to prepare for an RSI, ability to apply cricoid pressure, and understanding the modification of an RSI in special circumstances. An interactive e-learning package was produced and made available online. Twelve emergency department nurses took part in an evaluation of the e-learning package. All either agreed or strongly agreed that they had increased their knowledge and found the learning useful, and 11 out of 12 nurses reported being somewhat or very confident in the role of airway assistant following completion of the learning.

Comparison of waste anesthetic gases in operating rooms with or without an scavenging system in a Brazilian University Hospital

Directory of Open Access Journals (Sweden)

Leandro Gobbo Braz

2017-09-01

Full Text Available Background and objectives: Occupational exposure to waste anesthetic gases in operating room without active scavenging system has been associated with adverse health effects. Thus, this study aimed to compare the trace concentrations of the inhalational anesthetics isoflurane and sevoflurane in operating room with and without central scavenging system. Method: Waste concentrations of isoflurane and sevoflurane were measured by infrared analyzer at different locations (near the respiratory area of the assistant nurse and anesthesiologist and near the anesthesia station and at two times (30 and 120 min after the start of surgery in both operating room types. Results: All isoflurane and sevoflurane concentrations in unscavenged operating room were higher than the US recommended limit (2 parts per million, regardless of the location and time evaluated. In scavenged operating room, the average concentrations of isoflurane were within the limit of exposure, except for the measurements near the anesthesia station, regardless of the measurement times. For sevoflurane, concentrations exceeded the limit value at all measurement locations and at both times. Conclusions: The exposure to both anesthetics exceeded the international limit in unscavenged operating room. In scavenged operating room, the concentrations of sevoflurane, and to a lesser extent those of isoflurane, exceeded the recommended limit value. Thus, the operating room scavenging system analyzed in the present study decreased the anesthetic concentrations, although not to the internationally recommended values. Resumo: Justificativa e objetivos: A exposição ocupacional aos resíduos de gases anestésicos em salas de operação (SO sem sistema ativo de exaustão tem sido associada a efeitos adversos à saúde. Assim, o objetivo do estudo foi comparar os resíduos dos anestésicos inalatórios isoflurano e sevoflurano em SO com e sem sistema de exaustão. Método: Concentrações residuais

A multipurpose computing center with distributed resources

Science.gov (United States)

Chudoba, J.; Adam, M.; Adamová, D.; Kouba, T.; Mikula, A.; Říkal, V.; Švec, J.; Uhlířová, J.; Vokáč, P.; Svatoš, M.

2017-10-01

The Computing Center of the Institute of Physics (CC IoP) of the Czech Academy of Sciences serves a broad spectrum of users with various computing needs. It runs WLCG Tier-2 center for the ALICE and the ATLAS experiments; the same group of services is used by astroparticle physics projects the Pierre Auger Observatory (PAO) and the Cherenkov Telescope Array (CTA). OSG stack is installed for the NOvA experiment. Other groups of users use directly local batch system. Storage capacity is distributed to several locations. DPM servers used by the ATLAS and the PAO are all in the same server room, but several xrootd servers for the ALICE experiment are operated in the Nuclear Physics Institute in Řež, about 10 km away. The storage capacity for the ATLAS and the PAO is extended by resources of the CESNET - the Czech National Grid Initiative representative. Those resources are in Plzen and Jihlava, more than 100 km away from the CC IoP. Both distant sites use a hierarchical storage solution based on disks and tapes. They installed one common dCache instance, which is published in the CC IoP BDII. ATLAS users can use these resources using the standard ATLAS tools in the same way as the local storage without noticing this geographical distribution. Computing clusters LUNA and EXMAG dedicated to users mostly from the Solid State Physics departments offer resources for parallel computing. They are part of the Czech NGI infrastructure MetaCentrum with distributed batch system based on torque with a custom scheduler. Clusters are installed remotely by the MetaCentrum team and a local contact helps only when needed. Users from IoP have exclusive access only to a part of these two clusters and take advantage of higher priorities on the rest (1500 cores in total), which can also be used by any user of the MetaCentrum. IoP researchers can also use distant resources located in several towns of the Czech Republic with a capacity of more than 12000 cores in total.

Room temperature luminescence and ferromagnetism of AlN:Fe

Energy Technology Data Exchange (ETDEWEB)

Li, H., E-mail: lihui@mail.iee.ac.cn, E-mail: wjwang@aphy.iphy.ac.cn [The Key Laboratory of Solar Thermal Energy and Photovoltaic System, Institute of Electrical engineering, Chinese Academy of Sciences, Beijing 100190 (China); Cai, G. M. [School of Materials Science and Engineering, Central South University, Changsha, Hunan 410083 (China); Wang, W. J., E-mail: lihui@mail.iee.ac.cn, E-mail: wjwang@aphy.iphy.ac.cn [Research and Development Center for Functional Crystals, Beijing National Laboratory for Condensed Matter Physics, Institute of Physics, Chinese Academy of Sciences, Beijing 100190 (China)

2016-06-15

AlN:Fe polycrystalline powders were synthesized by a modified solid state reaction (MSSR) method. Powder X-ray diffraction and transmission electron microscopy results reveal the single phase nature of the doped samples. In the doped AlN samples, Fe is in Fe{sup 2+} state. Room temperature ferromagnetic behavior is observed in AlN:Fe samples. Two photoluminescence peaks located at about 592 nm (2.09 eV) and 598 nm (2.07 eV) are observed in AlN:Fe samples. Our results suggest that AlN:Fe is a potential material for applications in spintronics and high power laser devices.

Cognitive requirements in the redesign of a TRIGA RC-1 control room: The role of the operators' evaluations

International Nuclear Information System (INIS)

Visciola, M.; Bagnara, S.; Ruggeri, R.

1986-01-01

When a control room undergoes to a redesign process it is of crucial importance to analyze how operators critically review it and which improvements they suggest. This is even more critical when presumably the same people will operate in the new 'redesigned' control room: Consistency in the mental models possessed by the operators of the plant functions and of their control should be emphasized. Consistency in the mental models can be assumed when redesign follows well-established guidelines drawn from experiences and studies carried out in very similar situations. However, this condition is not fulfilled when a nuclear research control room has to be redesigned, since available guidelines (e.g.; NUREG-0700) are based on studies conducted on nuclear power plant control rooms. These two types of facilities are of much difference as for activities performed in the control room, goals to be aimed at, costs and risks. As a consequence, the available guidelines cannot be safely applied to such a situation as the redesign of a TRIGA RC-1 control room. So, data have to be collected in order to allow the operators to efficiently and easily adapt to the new control room by consistently 'updating' their mental models. In the present study, these data have been collected through structured interviews, which consisted of a modified version of EPRI. The results can be summarized as follows: 1) The operators critically reviewed the present control room and underlined the lack of 'transparency' of the control system as for the plant's conditions and for the feedbacks about their own activities. 2) The operators' work analysis showed that they spend much of their time out of the control room. This means that, if the operators have to stay in the control room, they should be allowed to perform more and higher-level activities than those presently required, to prevent understimulation. So, the redesign should or allow and support the central control and maintenance, and other

Implementation of the resource disincentive in 40 CFR Part 191.14(e) at the Waste Isolation Pilot Plant

International Nuclear Information System (INIS)

1991-08-01

In 1986, the US Department of Energy (DOE) Waste Isolation Pilot Plant (WIPP) Project Office (WPO) (DOE-WPO) prepared a strategy for complying with the Environmental Protection Agency's (EPA's) Standards for the management of transuranic (TRU) waste. Section 3.2.2.2 of the DOE's report addressed compliance with the Assurance Requirements found in 40 CFR Part 191.14. One of the Assurance Requirements addresses the selection of repository sites that contain recoverable natural resources and is referred to as the Resource Disincentive Requirement: This document addresses 40 CFR 191, Subpart B, Section 14 (e). The approach is to first summarize the development of the resource requirement to provide a proper perspective for evaluation of WIPP compliance. In addition, a summary of the discussions regarding resources at the WIPP is provided to demonstrate the extent to which the topic has been discussed between the DOE and various oversight groups. Finally, the information on resources at the WIPP site is presented, along with a summary of activities to mitigate negative impacts associated with the denial of resources. 77 refs., 3 figs., 3 tabs

Screening Criteria for a Room Cooling Failure of the AFW MDP Room

International Nuclear Information System (INIS)

Hwang, Mee Jeong; Yoon, Churl; Yang, Joon Eon; Park, Joo Hwan

2006-01-01

In this paper, we performed a heat up calculation for the Auxiliary Feedwater Motor Operated Pump (AFW MDP) room, PAB-077-11A with CFX-10 and RATT when the HVAC (Heating, Ventilation, and Air Condition) system is failed. We also reviewed the operability of the components under a loss of the HVAC. Room cooling failure does not need to be modeled if the components maintain their operability after a loss of a room cooling function during the mission time. ASME Standard describes that a recovery action can be credited if the related recovery action is included in the procedure or there are similar recovery experiences in the plant. However, there is no description about the recovery action of the HVAC in the EOP (Emergency Operation Procedure) of the UCN3, 4 under the situation of a loss of the HVAC. However, if we consider the HVAC failure in the PSA FT model, the problem is that the unavailability induced from a loss of the HVAC is unrealistically high. From a viewpoint of the PSA, it is not true that the related system always fails even if the HVAC system fails. Therefore, we reviewed the necessity of the HVAC model through two cases of a room heat up calculation under the situation of a loss of the HVAC system with conservative and realistic input data respectively

The development of a mobile CT-scanner gantry for use in the operating room

International Nuclear Information System (INIS)

Okudera, Hiroshi; Kobayashi, Shigeaki; Koike, Jouji; Harada, Takanobu; Kanemaru, Kei

1989-01-01

We report the development of a mobile CT-scanner gantry which uses a gantry platter. This system has been developed for use in the operating room. We designed a small lift to move the gantry unit of the scanner: the gantry carrier. The scanner gantry is fixed to the gantry carrier. A phantom test with a digitalized operating table worked well in the laboratory, and operating-room use showed that there was no deterioration in image quality. The mobile gantry system has been developed to increase the efficiency of the operating CT-scanner system. This system enables us to obtain CT images during surgery of immediately after surgery in the operating room, i.e., in cases that are not transferable to the radiological department. The operability is basically the same as that of a conventional mobile X-ray unit. Theoretically, this unit could be used with any CT scanner and in any operating room. (author)

Usability Testing for e-Resource Discovery: How Students Find and Choose e-Resources Using Library Web Sites

Science.gov (United States)

Fry, Amy; Rich, Linda

2011-01-01

In early 2010, library staff at Bowling Green State University (BGSU) in Ohio designed and conducted a usability study of key parts of the library web site, focusing on the web pages generated by the library's electronic resources management system (ERM) that list and describe the library's databases. The goal was to discover how users find and…

Non-local electrical spin injection and detection in germanium at room temperature

Science.gov (United States)

Rortais, F.; Vergnaud, C.; Marty, A.; Vila, L.; Attané, J.-P.; Widiez, J.; Zucchetti, C.; Bottegoni, F.; Jaffrès, H.; George, J.-M.; Jamet, M.

2017-10-01

Non-local carrier injection/detection schemes lie at the very foundation of information manipulation in integrated systems. This paradigm consists in controlling with an external signal the channel where charge carriers flow between a "source" and a well separated "drain." The next generation electronics may operate on the spin of carriers in addition to their charge and germanium appears as the best hosting material to develop such a platform for its compatibility with mainstream silicon technology and the predicted long electron spin lifetime at room temperature. In this letter, we demonstrate injection of pure spin currents (i.e., with no associated transport of electric charges) in germanium, combined with non-local spin detection at 10 K and room temperature. For this purpose, we used a lateral spin valve with epitaxially grown magnetic tunnel junctions as spin injector and spin detector. The non-local magnetoresistance signal is clearly visible and reaches ≈15 mΩ at room temperature. The electron spin lifetime and diffusion length are 500 ps and 1 μm, respectively, the spin injection efficiency being as high as 27%. This result paves the way for the realization of full germanium spintronic devices at room temperature.

Evaluation of a dark-room

International Nuclear Information System (INIS)

Passos, J.C.

1987-01-01

The adequate operation conditions of a dark-room are essential to guarantee the image quality, the least exposure of the patient and the staff, contributing also to reduce the expenses with specific equipments and processing solutions. Therefore, to install a dark-room, it is necessary a previous study about its physical dimensions, the location of equipments, accessories, light safeguards and visual warning, besides adequate darkening and correct filme processing. We propose three basic tests to check the adequacy and the integrity of a dark-room: light safeguards test, hygiene test, developing time and temperature test. (Author) [pt

Recovery Room

African Journals Online (AJOL)

defined postoperative unit or on the hospital ward. Patients were frequently transferred from the operating room directly to the ward where they were placed close to the nursing station. In 1947 the. Anesthesia Study Commission of the Philadelphia.

Hepatitis E

Science.gov (United States)

... room/fact-sheets/detail/hepatitis-e","@context":"http://schema.org","@type":"Article"}; العربية 中文 français русский español ... E: recognition, investigation and control”. The manual gives information about the epidemiology, clinical manifestations of the disease, ...

CSIR eNews: Natural resources and environment

CSIR Research Space (South Africa)

CSIR

2007-12-01

Full Text Available seeks to address the significant challenges regarding sustainable development in South Africa, with a focus on the optimal utilisation of natural resources in support of economic growth and human wellbeing....

Experimental and numerical study of the thermal performance of a new type of phase change material room

International Nuclear Information System (INIS)

Meng, Erlin; Yu, Hang; Zhan, Guangyi; He, Yang

2013-01-01

Highlights: • A new type of PCM room is proposed, two kinds of PCM were used in the room. • The new room can decrease the indoor air temperature fluctuation by 4.3 °C in summer. • Indoor air temperature fluctuation was decreased by 14.2 °C in winter for the new room. • Important factors that affect the thermal performance of the new room were studied. - Abstract: A new type of phase change material (PCM) room was proposed in this paper to control the indoor air temperature for a better thermal comfort for human beings. That is to place two different kinds of PCM into room envelopes of different orientations. Both experimental and numerical studies were carried out for rooms with/without PCM. Indoor air temperature and interior surface heat flux of the two rooms were studied in typical summer and winter climate of Shanghai (31.2N, 121.5E). Important factors that affect the thermal performance of the PCM were studied, such as phase change temperature, thickness of the PCM and the arrangement of the two kinds of PCM in the room. Results showed that this new type of PCM room can decrease the indoor air temperature fluctuation by 4.3 °C in summer and 14.2 °C in winter. Different arrangements of the two kinds of PCM in the room can cause an indoor air temperature difference to be 6.9 °C in summer and 2.7 °C in winter

Future control room design (modernization of control room systems); Zukuenftiges Wartendesign (Modernisierung von Warteneinrichtungen)

Energy Technology Data Exchange (ETDEWEB)

Reischl, Ludwig; Freitag, Timo; Dergel, Rene [AREVA NP (Germany). NLLR-G ' ' Reactor I and C' '

2009-07-01

In the frame of lifetime extension for nuclear power plants the modernization of the complete safety and operational control technology will be digitalized. It is also recommended to modernize the operator facilities, monitoring systems in the control room, the back-up shut-down center and the local control stations. The authors summarize the reasons for the modernization recommendations and discuss possible solutions for display-oriented control rooms. A concept for control room backfitting includes generic requirements, requirements of the local authorities, ergonomic principles information content and information density, and the design process. The backfitting strategy should include a cooperation with the operational personnel, The quality assurance and training via simulator needs sufficient timing during the implementation of the backfitting.

Ergonomics in the licensing and evaluation of nuclear reactors control room; A ergonomia no licenciamento e na avaliacao de salas de controle de reatores nucleares

Energy Technology Data Exchange (ETDEWEB)

Santos, Isaac Jose Antonio Luquetti dos [Instituto de Engenharia Nuclear (IEN), Rio de Janeiro, RJ (Brazil); Vidal, Mario Cesar Rodriguez [Universidade Federal, Rio de Janeiro, RJ (Brazil). Coordenacao dos Programas de Pos-graduacao de Engenharia. Programa de Engenharia de Producao

2002-07-01

A nuclear control room is a complex system that controls a thermodynamic process used to produce electrical energy. The operators interact with the control room through interfaces that have significant implications to nuclear plant safety and influence the operator activity. The TMI (Three Mile Island) accident demonstrated that only the anthropometric aspects were not enough for an adequate nuclear control room design. The studies showed that the accident was aggravated because the designers had not considered adequately human factor aspects. After TMI accident, the designers introduce in the nuclear control room development only human factors standards and human factors guidelines. The ergonomics approaches was not considered. Our objective is introduce in nuclear control room design and nuclear control room evaluation, a methodology that. includes human factors standards, human factors guidelines and ergonomic approaches, the operator activity analysis. (author)

Ergonomics influence on control room layout

International Nuclear Information System (INIS)

Hartfiel, H.D.

1984-01-01

Nowadays, human factors has become an important aspect of the design of work places. Since the control room in a nuclear power plant is a work place, too, its layout is also influenced by ergonomics. With the KWU control room concept for the 1300 MW PWR as an example, we show how assured and applicable ergonomic findings enter into the control room design. On the basis of general design principles for work places, specific methods for control room planning have been developed. By working with these methods a concept that makes it possible to build a man-machine interface able to fulfill the process control tasks with all their underlying conditions has been derived. (author)

Nuclear power station main control room habitability

International Nuclear Information System (INIS)

Paschal, W.B.; Knous, W.S.

1989-01-01

The main control room at a nuclear power station must remain habitable during a variety of plant conditions and postulated events. The control room habitability requirement and the function of the heating, ventilating, air-conditioning, and air treatment system are to control environmental factors, such as temperature, pressure, humidity, radiation, and toxic gas. Habitability requirements provide for the safety of personnel and enable operation of equipment required to function in the main control room. Habitability as an issue has been gaining prominence with the Advisor Committee of Reactor Safeguards and the Nuclear Regulatory Commission since the incident at Three Mile Island. Their concern is the ability of the presently installed habitability systems to control the main control room environment after an accident. This paper discusses main control room HVAC systems; the concern, requirements, and results of NRC surveys and notices; and an approach to control room habitability reviews

Tactical decision making for selective expansion of operating room resources incorporating financial criteria and uncertainty in subspecialties' future workloads.

Science.gov (United States)

Dexter, Franklin; Ledolter, Johannes; Wachtel, Ruth E

2005-05-01

We considered the allocation of operating room (OR) time at facilities where the strategic decision had been made to increase the number of ORs. Allocation occurs in two stages: a long-term tactical stage followed by short-term operational stage. Tactical decisions, approximately 1 yr in advance, determine what specialized equipment and expertise will be needed. Tactical decisions are based on estimates of future OR workload for each subspecialty or surgeon. We show that groups of surgeons can be excluded from consideration at this tactical stage (e.g., surgeons who need intensive care beds or those with below average contribution margins per OR hour). Lower and upper limits are estimated for the future demand of OR time by the remaining surgeons. Thus, initial OR allocations can be accomplished with only partial information on future OR workload. Once the new ORs open, operational decision-making based on OR efficiency is used to fill the OR time and adjust staffing. Surgeons who were not allocated additional time at the tactical stage are provided increased OR time through operational adjustments based on their actual workload. In a case study from a tertiary hospital, future demand estimates were needed for only 15% of surgeons, illustrating the practicality of these methods for use in tactical OR allocation decisions.

A remote control room at DIII-D

International Nuclear Information System (INIS)

Abla, G.; Schissel, D.P.; Penaflor, B.G.; Wallace, G.

2008-01-01

This paper describes a remote control room built at DIII-D to support remote participation activities of DIII-D research staff. In order to create a persistent, efficient, and reliable remote participation environment for DIII-D scientists, a remote control room has been built in a 640-ft 2 dedicated area. The purpose of this room is to experiment and define a remote control room framework that can facilitate the remote participation needs of current and future fusion experiments such as ITER. A variety of hardware equipment has been installed and several remote participation and collaboration technologies have been deployed. Objectivity and practical consideration has been the key while designing the room and deploying the technologies. Although, the DIII-D remote control room is still a work in progress and new software tools are being implemented, it has been already useful for a number of international remote participation activities. For example, it has been used for remote support of the EAST Tokamak in China during the start up operation and proven effective for other collaborative experiment activities. The description of the remote control room design is given along with technologies deployed for remote collaboration needs. We will also discuss our recent experiences involving the DIII-D remote control room as well as future plans for improvements

Synthesis of Room Impulse Responses for Variable Source Characteristics

Directory of Open Access Journals (Sweden)

M. Kunkemoeller

2011-01-01

Full Text Available Every acoustic source, e.g. a speaker, a musical instrument or a loudspeaker, generally has a frequency dependent characteristic radiation pattern, which is preeminent at higher frequencies. Room acoustic measurements nowadays only account for omnidirectional source characteristics. This motivates a measurement method that is capable of obtaining room impulse responses for these specific radiation patterns by using a superposition approach of several measurements with technically well-defined sound sources. We propose a method based on measurements with a 12-channel independentlydriven dodecahedron loudspeaker array rotated by an automatically controlled turntable.Radiation patterns can be efficiently described with the use of spherical harmonics representation. We propose a method that uses this representation for the spherical loudspeaker array used for the measurements and the target radiation pattern to be used for the synthesis.We show validating results for a deterministic test sound source inside in a small lecture hall.

Stability of disposal rooms during waste retrieval

International Nuclear Information System (INIS)

Brandshaug, T.

1989-03-01

This report presents the results of a numerical analysis to determine the stability of waste disposal rooms for vertical and horizontal emplacement during the period of waste retrieval. It is assumed that waste retrieval starts 50 years after the initial emplacement of the waste, and that access to and retrieval of the waste containers take place through the disposal rooms. It is further assumed that the disposal rooms are not back-filled. Convective cooling of the disposal rooms in preparation for waste retrieval is included in the analysis. Conditions and parameters used were taken from the Nevada Nuclear Waste Storage Investigation (NNWSI) Project Site Characterization Plan Conceptual Design Report (MacDougall et al., 1987). Thermal results are presented which illustrate the heat transfer response of the rock adjacent to the disposal rooms. Mechanical results are presented which illustrate the predicted distribution of stress, joint slip, and room deformations for the period of time investigated. Under the assumption that the host rock can be classified as ''fair to good'' using the Geomechanics Classification System (Bieniawski, 1974), only light ground support would appear to be necessary for the disposal rooms to remain stable. 23 refs., 28 figs., 2 tabs

Consumer opinions of emergency room medical care.

Science.gov (United States)

McMillan, J R; Younger, M S; DeWine, L C

1984-12-01

If hospital management is to adapt successfully to an increasingly competitive environment, and to retain a viable emergency department, it well be necessary to objectively and accurately assess the hospital's image in the community served. Knowledge of the consumers' views is an essential input into the formulation of strategic plans. This article reports on a study in which consumer opinions on 15 dimensions of emergency room health care were obtained from 723 respondents using a mail questionnaire. Findings reveal that consumers view the emergency room as being more expensive than other health care providers. Except for being available or convenient, little or no advantage is perceived for the emergency room over the personal physician. Even though the emergency room has specialized staff and equipment, consumers do not believe patients receive better or faster treatment in an emergency room than would be obtained in a physician's office. Unless changed, these perceptions will diminish the role of the emergency room in the delivery of health care services.

How has problem based learning fared in Pakistan?

Science.gov (United States)

Mahmud, Waqas; Hyder, Omar

2012-10-01

To conduct a systematic review of primary research in undergraduate medical education in Pakistan in order to evaluate PBL programs, examine outcomes and competencies influenced by PBL, and compare them with conventional learning (lecture based learning, LBL). Qualitative content analysis. Rawalpindi Medical College, Rawalpindi, from June 2010 - February 2011. Literature was searched using online resources. Studies evaluating outcomes influenced by PBL, or comparing PBL with lecture based learning (LBL) were selected. Due to heterogeneity, a qualitative content analysis was performed in which studies were classified according to the methods of assessment; results were then summarized by outcome and frequencies were calculated. Eleven studies were included. Apart from knowledge acquisition, students gave high ratings to PBL in selected outcomes, alone, and in comparison with LBL. There was a disagreement among results of studies that evaluated knowledge acquisition alone. Based on student perceptions, PBL has many advantages. However, the results of this review are limited due to heterogeneity and methodological weakness of studies, specially the studies that compared exam scores to assess knowledge acquisition.

46 CFR 111.105-41 - Battery rooms.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Battery rooms. 111.105-41 Section 111.105-41 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING ELECTRIC SYSTEMS-GENERAL REQUIREMENTS Hazardous Locations § 111.105-41 Battery rooms. Each electrical installation in a battery room...

Madness in Sartre's "The Room"

NARCIS (Netherlands)

Jongeneel, E.C.S.

2009-01-01

In "The Room," part of his short story collection, The Wall (1938), Jean-Paul Sartre investigates madness as an alternative way of bourgeois life and thus takes a stand in the contemporary debate on the existential status of mental illness. "The Room" is a case-study of a "limit situation," as well

Room temperature luminescence and ferromagnetism of AlN:Fe

Directory of Open Access Journals (Sweden)

H. Li

2016-06-01

Full Text Available AlN:Fe polycrystalline powders were synthesized by a modified solid state reaction (MSSR method. Powder X-ray diffraction and transmission electron microscopy results reveal the single phase nature of the doped samples. In the doped AlN samples, Fe is in Fe2+ state. Room temperature ferromagnetic behavior is observed in AlN:Fe samples. Two photoluminescence peaks located at about 592 nm (2.09 eV and 598 nm (2.07 eV are observed in AlN:Fe samples. Our results suggest that AlN:Fe is a potential material for applications in spintronics and high power laser devices.

27 CFR 24.166 - Buildings or rooms.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Buildings or rooms. 24.166... OF THE TREASURY LIQUORS WINE Construction and Equipment § 24.166 Buildings or rooms. All buildings or... afford adequate protection to the revenue. Each building or room will be constructed of substantial...

New Radiation Protection training room

CERN Multimedia

HSE Unit

2013-01-01

From now on, the theory and practical components of the Radiation Protection training, developed by the RP Group and offered by the HSE Unit’s Safety Training team to people working in a Controlled Radiation Area, will take place in a dedicated teaching room, designed specifically for this kind of training.   The new room is in the Safety Training Centre on the Prévessin site and has been open since 16 October. It has an adjoining workshop that, like the room itself, can accommodate up to 12 people. It is also equipped with an interactive board as well as instruments and detectors to test for ionising radiation. This room is located near the recently inaugurated LHC tunnel mock-up where practical training exercises can be carried out in conditions almost identical to those in the real tunnel. To consult the safety training catalogue and/or sign up for Radiation Protection training, please go to: https://cta.cern.ch For further information, please contact the Safety Trainin...

Measurement of low-frequency noise in rooms

DEFF Research Database (Denmark)

Pedersen, Steffen; Møller, Henrik; Persson-Waye, Kerstin

2006-01-01

Measurement of low-frequency noise in rooms is problematic due to standing wave patterns. The spatial variation in the sound pressure level can typically be as much as 20-30 dB. For assessment of annoyance from low-frequency noise in dwellings, it is important to measure a level close...... rooms. The sound pressure level was measured 1) in three-dimensional corners and 2) according to current Swedish and Danish measurement methods. Furthermore, the entire sound pressure distributions were measured by scanning. The Swedish and Danish measurement methods include a corner measurement...... to the highest level present in a room, rather than a room average level. In order to ensure representative noise measurements, different positions were investigated based on theoretical considerations and observations from numerical room simulations. In addition measurements were performed in three different...

Perceptual effects in auralization of virtual rooms

Science.gov (United States)

Kleiner, Mendel; Larsson, Pontus; Vastfjall, Daniel; Torres, Rendell R.

2002-05-01

By using various types of binaural simulation (or ``auralization'') of physical environments, it is now possible to study basic perceptual issues relevant to room acoustics, as well to simulate the acoustic conditions found in concert halls and other auditoria. Binaural simulation of physical spaces in general is also important to virtual reality systems. This presentation will begin with an overview of the issues encountered in the auralization of room and other environments. We will then discuss the influence of various approximations in room modeling, in particular, edge- and surface scattering, on the perceived room response. Finally, we will discuss cross-modal effects, such as the influence of visual cues on the perception of auditory cues, and the influence of cross-modal effects on the judgement of ``perceived presence'' and the rating of room acoustic quality.

Mathematical Models for Room Air Distribution

DEFF Research Database (Denmark)

Nielsen, Peter V.

1982-01-01

A number of different models on the air distribution in rooms are introduced. This includes the throw model, a model on penetration length of a cold wall jet and a model for maximum velocity in the dimensioning of an air distribution system in highly loaded rooms and shows that the amount of heat...... removed from the room at constant penetration length is proportional to the cube of the velocities in the occupied zone. It is also shown that a large number of diffusers increases the amount of heat which may be removed without affecting the thermal conditions. Control strategies for dual duct and single...... duct systems are given and the paper is concluded by mentioning a computer-based prediction method which gives the velocity and temperature distribution in the whole room....

7 CFR 58.211 - Packaging room for bulk products.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Packaging room for bulk products. 58.211 Section 58... Service 1 Rooms and Compartments § 58.211 Packaging room for bulk products. A separate room or area shall... dust within the packaging room and where needed, a dust collector shall be provided and properly...

Room acoustic transition time based on reflection overlap

DEFF Research Database (Denmark)

Jeong, Cheol-Ho; Brunskog, Jonas; Jacobsen, Finn

2010-01-01

A transition time is defined based on the temporal overlap of reflected pulses in room impulse responses. Assuming specular reflections only, the temporal distance between adjacent reflections, which is proportional to the volume of a room, is compared with the characteristic width of a pulse at ...... in a room with nonuniform absorption and furniture than in a room that satisfies the underlying assumptions....

Room acoustic transition time based on reflection overlap

DEFF Research Database (Denmark)

Jeong, Cheol-Ho; Brunskog, Jonas; Jacobsen, Finn

2013-01-01

A transition time is defined based on the temporal overlap of reflected pulses in room impulse responses. Assuming specular reflections only, the temporal distance between adjacent reflections, which is proportional to the volume of a room, is compared with the characteristic width of a pulse at ...... in a room with nonuniform absorption and furniture than in a room that satisfies the underlying assumptions....

Physics escape room as an educational tool

Science.gov (United States)

Vörös, Alpár István Vita; Sárközi, Zsuzsa

2017-12-01

Escape rooms have flourished in the last decade. These are adventure games in which players work together to solve puzzles using hints, clues and a strategy to escape from a locked room. In many cases they use different phenomena related to physics. Hence the idea of using escape rooms in science centers or even in classroom activities. Escape rooms are designed for one single team of players, the method is more suitable for activities in a science centre. In our paper, we show that escape rooms' puzzle solving methods could be used in physics classroom activities as well, taking into account that several teams have to work together in the same room/place. We have developed an educational escape game for physics of fluids, as this topic is left out from the Romanian high-school curriculum. We have tried out our game during the project week called "Şcoala altfel" ("school in a different way") and in a physics camp for gifted students. We present the designed physics escape game and the results.

Waste Management Quality Assurance Plan

International Nuclear Information System (INIS)

1993-01-01

Lawrence Berkeley Laboratory's Environment Department addresses its responsibilities through activities in a variety of areas. The need for a comprehensive management control system for these activities has been identified by the Department of Energy (DOE). The WM QA (Waste Management Quality Assurance) Plan is an integral part of a management system that provides controls necessary to ensure that the department's activities are planned, performed, documented, and verified. This WM QA Plan defines the requirements of the WM QA program. These requirements are derived from DOE Order 5700.6C, Quality Assurance, the LBL Operating and Assurance Program Plan (OAP, LBL PUB-3111), and other environmental compliance documents applicable to WM activities. The requirements presented herein, as well as the procedures and methodologies that direct the implementation of these requirements, will undergo review and revisions as necessary. The provisions of this QA Plan and its implementing documents apply to quality-affecting activities performed by and for WM. It is also applicable to WM contractors, vendors, and other LBL organizations associated with WM activities, except where such contractors, vendors, or organizations are governed by their own WM-approved QA programs. References used in the preparation of this document are (1) ASME NQA-1-1989, (2) ANSI/ASQC E4 (Draft), (3) Waste Management Quality Assurance Implementing Management Plan (LBL PUB-5352, Rev. 1), (4) LBL Operating and Assurance Program Plan (OAP), LBL PUB-3111, 2/3/93. A list of terms and definitions used throughout this document is included as Appendix A

Study of low noise preamplifier systems for use with room temperature mercuric iodide (HgI2) x-ray detectors

International Nuclear Information System (INIS)

Iwanczyk, J.S.; Dabrowski, A.J.; Huth, G.C.; Del Duca, A.; Schenpple, W.

1980-01-01

An analysis of different preamplification systems for use with room temperature mercuric iodide x-ray detectors has been performed. Resistor-, drain-, and light-feedback preamplifiers have been studied. Energy resolution of 295 eV (FWHM) for Fe-55 source (5.9 keV) and 225 eV (FWHM) for the pulser have been obtained with both the detector and the input FET at room temperature using the pulsed-light feedback preamplifier. It has been shown that cooling the input FET using a small Peltier element allows the energy resolution to be improved up to 25%

Complete rooming-in care of newborn infants

Directory of Open Access Journals (Sweden)

Yoo Min Lee

2010-05-01

Full Text Available Purpose : In Kyung Hee East-West Neo Medical Center, Seoul,Korea, efforts to raise rooming-in care success rate have been undertaken since when the hospital was established in 2006. We intended to analyze our experience over the past 3 years of period and to discuss the advantages of rooming-in. Methods : We analyzed the rooming-in practice rate, failure rate, and the breast feeding rate. Subjects were 860 normal healthy neonates from June 2006 to June 2009. Results: Among these 860 cases, 83 babies were required separation out of rooming-in in the middle of the course. Among these 83 cases, 70 cases had to stop the course due to poor condition of babies and 13 cases due to maternal condition. 70 cases of infant’s causes consist of 68 cases of NICU admission and 2 cases of poor feeding support. The other 13 cases of separation include refusal by maternal condition. Therefore the success rate of rooming-in for the last 3 years was 90.3%, that is 777 cases among the total 860 cases. The percentage of exclusive breast feeding was 64%, that of mixed feeding with breast and formula feeding was 25%, and formula feeding only was 11%. Conclusion : We experienced successful rooming-in care for the last 3 years. Nursery facilities should educate and encourage the advantages of rooming-in, including the good formation of attachment between mother and infant, emotional stability, protection from infection, and increased breast feeding rate so that rooming-in care can be fully established.

Foucault could have been an operating room nurse.

Science.gov (United States)

Riley, Robin; Manias, Elizabeth

2002-08-01

Operating room nursing is an under-researched area of nursing practice. The stereotypical image of operating room nursing is one of task- and technically-orientated aspects of practice, where nurses work in a medical model and are dominated by constraints from outside their sphere of influence. This paper explores the possibility of understanding operating room nursing in a different way. Using the work of Michel Foucault to analyse the work of operating room nursing, this paper argues the relevance of the framework for a more in-depth analysis of this specialty area of practice. The concepts of power, discipline and subjectivity are used to demonstrate how operating room nursing is constructed as a discipline and how operating room nurses act to govern and construct the specialty. Exemplars are drawn from extensive professional experience, from guidelines of professional operating room nursing associations, as well as published texts. The focus is predominantly on the regulation of space and time to maintain the integrity of the sterile surgical field and issues of management, as well as the use of the ethical concept of the 'surgical conscience'. This form of analysis provides a level and depth of inquiry that has rarely been undertaken in operating room nursing. As such, it has the potential to provide a much needed, different view of operation room nursing that can only help to strengthen its professional foundations and development.

Integrated Resource Management and Recovery

DEFF Research Database (Denmark)

Astrup, Thomas Fruergaard

2014-01-01

, depends on the quality of these resources and technological abilities to extract resources from mixed materials, e.g. mobile phones, solar cells, or mixed domestic waste. The "effort" invested in recovery of secondary resources should not be more than the "benefit" associated with the secondary resources...

Case review analysis of operating room decisions to cancel surgery.

Science.gov (United States)

Chang, Ju-Hsin; Chen, Ke-Wei; Chen, Kuen-Bao; Poon, Kin-Shing; Liu, Shih-Kai

2014-07-23

Cancellation of surgery close to scheduled time causes a waste of healthcare resources. The current study analyzes surgery cancellations occurring after the patient has been prepared for the operating room, in order to see whether improvements in the surgery planning process may reduce the number of cancellations. In a retrospective chart review of operating room surgery cancellations during the period from 2006 to 2011, cancellations were divided into the following categories: inadequate NPO; medical; surgical; system; airway; incomplete evaluation. The relative use of these reasons in relation to patient age and surgical department was then evaluated. Forty-one percent of cancellations were for other than medical reasons. Among these, 17.7% were due to incomplete evaluation, and 8.2% were due to family issues. Sixty seven percent of cancelled cases eventually received surgery. The relative use of individual reasons for cancellation varied with patient age and surgical department. The difference between cancellations before and after anesthesia was dependent on the causes of cancellation, but not age, sex, ASA status, or follow-up procedures required. Almost half of the cancellations were not due to medical reasons, and these cancellations could be reduced by better administrative and surgical planning and better communication with the patient and/or his family.

Quantum Correlations of Light from a Room-Temperature Mechanical Oscillator

Science.gov (United States)

Sudhir, V.; Schilling, R.; Fedorov, S. A.; Schütz, H.; Wilson, D. J.; Kippenberg, T. J.

2017-07-01

When an optical field is reflected from a compliant mirror, its intensity and phase become quantum-correlated due to radiation pressure. These correlations form a valuable resource: the mirror may be viewed as an effective Kerr medium generating squeezed states of light, or the correlations may be used to erase backaction from an interferometric measurement of the mirror's position. To date, optomechanical quantum correlations have been observed in only a handful of cryogenic experiments, owing to the challenge of distilling them from thermomechanical noise. Accessing them at room temperature, however, would significantly extend their practical impact, with applications ranging from gravitational wave detection to chip-scale accelerometry. Here, we observe broadband quantum correlations developed in an optical field due to its interaction with a room-temperature nanomechanical oscillator, taking advantage of its high-cooperativity near-field coupling to an optical microcavity. The correlations manifest as a reduction in the fluctuations of a rotated quadrature of the field, in a frequency window spanning more than an octave below mechanical resonance. This is due to coherent cancellation of the two sources of quantum noise contaminating the measured quadrature—backaction and imprecision. Supplanting the backaction force with an off-resonant test force, we demonstrate the working principle behind a quantum-enhanced "variational" force measurement.

Implementation of the Resource Disincentive in 40 CFR part 191.14 (e) at the Waste Isolation Pilot Plant. Revision 1

Energy Technology Data Exchange (ETDEWEB)

1993-06-01

In 1986, the US Department of Energy (DOE) Waste Isolation Pilot Plant (WIPP) Project Office (WPO) (DOE-WPO) prepared a strategy for complying with the Environmental Protection Agency`s (EPA`s) Standards for the management of transuranic (TRU) waste. Section 3.2.2.2 of the DOE`s report addressed compliance with the Assurance Requirements found in 40 CFR {section} 191.14. One of the Assurance Requirements addresses the selection of repository sites that contain recoverable natural resources. This report documents that the site selection process for the WIPP facility did indeed comply with the natural resource disincentive requirement in 40 CFR {section} 191,14(e) at the time selected and therefore complies with the standard at this time. Thus, it shall be shown that it is reasonably certain that the WIPP site provides better overall protection than practical alternatives that were available when the site was selected. It is important to point out here, and it will be discussed later in the report, that the resource disincentive requirement is a preliminary siting criterion that requires further evaluation of sites that have resources (i.e, hydrocarbons, minerals and groundwater) in the vicinity or on the site. This further evaluation requires that for sites that do have resources, a qualitative determination must be made that the site will provide better overall protection than practical alternatives. The purpose of this report is not to provide a quantitative evaluation for selection of the WIPP site. A further discussion on the difference between the qualitative analysis required under 40 CFR {section} 191.14(e) and the quantitative analysis under other sections of 40 CFR 191 is provided in {section}2.1 of this report.

Rethinking theatre in modern operating rooms.

Science.gov (United States)

Riley, Robin; Manias, Elizabeth

2005-03-01

Metaphor is a means through which a widely accepted meaning of a word is used in a different context to add understanding that would otherwise be difficult to conceive. Through etymological and metaphorical associations, we contend that aspects of "theatre" are still relevant in the modern operating rooms and that the use of dramaturgical metaphors can add another layer of understanding about the social reality in this setting. We begin by exploring the historical roots and derivation of the word theatre as it applied to anatomical dissection and surgery. Briefly, we touch on the work of Erving Goffman and examine how his work has been used by others to explore aspects of operating room nursing. Then, drawing on data from a postmodern ethnographic study that has been used to examine communication in operating room nursing, four dramaturgical metaphors are used to illustrate the argument. They are drama, the script and learning the lines, the show must go on, and changing between back stage and front stage. To conclude, the small amount of previously published literature on this topic is compared and contrasted, and the relevance of using dramaturgical metaphors to understand modern operating rooms is discussed. Being able to distinguish between the inherent drama in operating room work and the dramatic realisation of individuals who work within, can help operating room nurses to think differently about, and perhaps re-evaluate their social situation and how they function within it.

Assessment of abuse-related injuries: a comparative study of forensic physicians, emergency room physicians, emergency room nurses and medical students.

Science.gov (United States)

Reijnders, Udo J L; Giannakopoulos, Georgios F; de Bruin, Kim H

2008-01-01

A comparative study was made investigating whether emergency room physicians, emergency room nurses, forensic physicians, and interns are competent in describing, recognising and determining the possible cause of injuries. The injury assessment scores varied from good--adequate--fail and remained blank in various participant groups. Forensic physicians scored significantly better than emergency room staff and interns in the assessment of abuse-related injuries. There were almost no differences noted between emergency room physicians and emergency room nurses. For the functional group with more or less than 4 to 6 years of experience, no significant differences were noted for scoring good in all 5 cases. The fact that forensic physicians scored better than the emergency room staff is probably explained by the fact that almost all practicing forensic physicians have been officially qualified. Training in this field for all professionals involved in such assessment should be mandatory.

A control room lighting study

International Nuclear Information System (INIS)

Vaidya, V.V.; Iwasa-Madge, K.M.; Howard, B.; Willson, R.B.

1984-01-01

Operators at a Heavy Water Plant in Ontario, Canada complained about lighting-related difficulties in the control room. The Human Factors Engineering Unit was requested to perform a lighting survey and make recommendations to improve the control centre lighting conditions. This paper describes the control room, the operator tasks, the procedures used for the lighting survey, the findings, and the changes recommended

New thinking for the boiler room.

Science.gov (United States)

Rose, Wayne

2008-09-01

Wayne Rose, marketing manager at integrated plant room manufacturer Armstrong Integrated Systems, explains how increasing use of off-site manufacture, the latest 3D modelling technology, and advances in control technology, are revolutionising boiler room design and construction.

[Advanced Trauma Life Support (ATLS) in the emergency room. Is it suitable as an SOP?].

Science.gov (United States)

Shafizadeh, S; Tjardes, T; Steinhausen, E; Balke, M; Paffrath, T; Bouillon, B; Bäthis, H

2010-08-01

There is clinical evidence that a standardized management of trauma patients in the emergency room improves outcome. ATLS is a training course that teaches a systematic approach to the trauma patient in the emergency room. The aims are a rapid and accurate assessment of the patient's physiologic status, treatment according to priorities, and making decisions on whether the local resources are sufficient for adequate definitive treatment of the patient or if transfer to a trauma center is necessary. Above all it is important to prevent secondary injury, to realize timing as a relevant factor in the initial treatment, and to assure a high standard of care. A standard operating procedure (SOP) exactly regulates the approach to trauma patients and determines the responsibilities of the involved faculties. An SOP moreover incorporates the organizational structure in the treatment of trauma patients as well as the necessary technical equipment and staff requirements. To optimize process and result quality, priorities are in the fields of medical fundamentals of trauma care, education, and fault management. SOPs and training courses increase the process and result quality in the treatment of the trauma patient in the emergency room. These programs should be based on the special demands of the physiology of the trauma as well as the structural specifics of the hospital. ATLS does not equal an SOP but it qualifies as a standardized concept for management of trauma patients in the emergency room.

Role of Magnetocardiography in Emergency Room

International Nuclear Information System (INIS)

Kwon, H.; Kim, K.; Kim, J. M.; Lee, Y. H.; Kim, T. E.; Lim, H. K.; Park, Y. K.; Ko, Y. G.; Chung, N.

2006-01-01

In emergency rooms, patients with acute chest pain should be diagnosed as quickly as possible with higher diagnostic accuracy for an appropriate therapy to the patients with acute coronary syndrome or for avoiding unnecessary hospital admissions. At present, electrocardiography(ECG) and biochemical markers are generally used to detect myocardial infarction and coronary angiography is used as a gold standard to reveal the degree of narrowing of coronary artery. Magnetocardiography(MCG) has been proposed as a novel and non-invasive diagnostic tool fur the detection of cardiac electrical abnormality associated with myocardial ischemia. In this study, we examined whether the MCG can be used fur the detection of coronary artery disease(CAD) in patients, who were admitted to the emergency room with acute chest pain. MCG was recorded from 36 patients admitted to the emergency room with suspected acute coronary syndrome. The MCG recordings were obtained using a 64-channel SQUID MCG system in a magnetically shielded room. In result, presence of CAD could be found with a sensitivity of 88.2 % in patients with acute chest pain without 57 elevation in ECG, demonstrating a possible use in the emergency room to screen CAD patients.

Revisiting the Operating Room Basics

Directory of Open Access Journals (Sweden)

Tushar Chakravorty

2015-12-01

Full Text Available Young doctors walking into the operating room are eager to develop their skills to become efficient and knowledgeable professionals in future. But precious little is done to actively develop the basic practical skills of the budding doctors. They remain unaware about the layout of the operating room, the OR etiquette and often do not have sound scientific understanding and importance of meticulous execution of the basic operating room protocols. This article stresses the need to develop the basics of OR protocol and to improve the confidence of the young doctor by strengthening his foundation by showing him that attention to the basics of medical care and empathy for the patient can really make a difference to the outcome of a treatment.

Beam-beam issues in asymmetric colliders

International Nuclear Information System (INIS)

Furman, M.A.

1992-07-01

We discuss generic beam-beam issues for proposed asymmetric e + - e - colliders. We illustrate the issues by choosing, as examples, the proposals by Cornell University (CESR-B), KEK, and SLAC/LBL/LLNL (PEP-II)

Measuring quality indicators in the operating room: cleaning and turnover time Mensuración de indicadores de calidad en un centro quirúrgico: tiempo de limpieza e intervalo entre cirugías Mensuração de indicadores de qualidade em centro cirúrgico: tempo de limpeza e intervalo entre cirurgias

Directory of Open Access Journals (Sweden)

Marli de Carvalho Jericó

2011-10-01

Full Text Available This exploratory-descriptive study was carried out in the Surgical Center Unit of a university hospital aiming to measure time spent with concurrent cleaning performed by the cleaning service and turnover time and also investigated potential associations between cleaning time and the surgery's magnitude and specialty, period of the day and the room's size. The sample consisted of 101 surgeries, computing cleaning time and 60 surgeries, computing turnover time. The Kaplan-Meier method was used to analyze time and Pearson's correlation to study potential correlations. The time spent in concurrent cleaning was 7.1 minutes and turnover time was 35.6 minutes. No association between cleaning time and the other variables was found. These findings can support nurses in the efficient use of resources thereby speeding up the work process in the operating room.Este estudio exploratorio y descriptivo fue conducido en la Unidad de Centro Quirúrgico de un hospital de enseñanza teniendo por objetivos mensurar el tiempo utilizado para limpieza concurrente en sala de operación (por el Servicio de Higiene y Limpieza y el intervalo entre las cirugías; e, investigar las asociaciones entre: tiempo de limpieza, porte de la cirugía, especialidad de la cirugía, período de ocurrencia y tamaño de la sala. El estudio fue constituido de 101 casos de limpieza (estudio de tiempo de limpieza y 60 cirugías (estudio de intervalo entre cirugías. El método de Kaplan-Meier fue utilizado para el análisis del tiempo y la correlación de Pearson para el estudio de las asociaciones. El tiempo promedio de limpieza concurrente de la sala fue de 7,1 minutos y el del intervalo entre cirugías de 35,6 minutos. No fue encontrada correlación entre el tiempo de limpieza y las demás variables. Estos hallazgos instrumentalizan a los enfermeros en el uso eficiente de recursos, agilizando el proceso de trabajo en el Centro Quirúrgico.Este estudo exploratório-descritivo foi

The changing sensory room

DEFF Research Database (Denmark)

2018-01-01

In 2017 the kindergarten The Milky Way in the city Vejle in Denmark made a sensory room that has the special ability change whenever wanted by the children and social educators. Kjetil Sandvik (to the right) from Copenhagen University and Klaus Thestrup from Aarhus University reflects upon what...... they saw, took part in and talked with the social educators about. Jacob Knudsen from VIFIN filmed the two gentlemen and organised the project. it is a room composed around common experiments, many self-made objects, open narrative structures. and a combination of digital and analogue elements....

76 FR 18578 - Notice of Public Meeting: Northwest California Resource Advisory Council

Science.gov (United States)

2011-04-04

... transportation, beverages and food. On April 29, the council convenes at 8 a.m. in the conference room of the BLM... DEPARTMENT OF THE INTERIOR Bureau of Land Management [LLCAN01000.L10200000.XZ0000] Notice of Public Meeting: Northwest California Resource Advisory Council AGENCY: Bureau of Land Management...

Clean industrial room for drift tube assembling

International Nuclear Information System (INIS)

Glonti, G.L.; Gongadze, A.L.; Evtukhovich, P.G.

2001-01-01

Description of a clean industrial room for assembly of drift tubes for the muon spectrometer of the ATLAS experiment is presented. High quality specifications on the detectors to be produced demanded creation of a workplace with stable temperature and humidity, as well as minimum quantity of dust in the room. Checking of parameters of intra-room air during long period of continuous work has confirmed correctness of the designed characteristics of the climatic system installed in the clean room. The room large volume (∼ 190 m 3 ), the powerful and flexible climatic system, and simplicity of service allow assembling of detectors with length up to 5 m. Subsequent checking of functionality of the assembled detectors has shown high quality of assembling (the amount of rejected tubes does not exceed 2%). It demonstrates conformity to the assembling quality requirements for mass production of drift chambers for the muon spectrometer. (author)

Clean Industrial Room for Drift Tube Assembling

CERN Document Server

Glonti, GL; Evtoukhovitch, P G; Kroa, G; Manz, A; Potrap, I N; Rihter, P; Stoletov, G D; Tskhadadze, E G; Chepurnov, V F; Chirkov, A V; Shelkov, G A

2001-01-01

Description of a clean industrial room for assembly of drift tubes for the muon spectrometer of the ATLAS experiment is presented. High quality specifications on the detectors to be produced demanded creation of a workplace with stable temperature and humidity, as well as minimum quantity of dust in the room. Checking of parameters of intra-room air during long period of continuous work has been confirmed correctness of the designed characteristics of the climatic system installed in the clean room. The room large volum (\\sim 190 m^3), the powerful and flexible climatic system, and simplicity of service allow assembling of detectors with length up to 5 m. Subsequent checking of functionality of the assembled detectors has shown high quality of assembling (the amount of rejected tubes does not exceed 2 %). It demonstrates conformity to the assembling quality requirements for mass production of drift chambers for the muon spectrometer.

Control room habitability in Spanish Nuclear Power Plants

International Nuclear Information System (INIS)

Mediavilla, F.; Sierra, J. J.

2007-01-01

Since the NRC published in 2003 the Generic Letter 2003-01 Control room Habitability and the Regulatory guide 1.197 Demonstrating Control Room Envelope Integrity at Nuclear Power Reactors, where it is emphasized the importance of verifying the control room habitability by means of alternative methods, Spanish Nuclear Power Plants are undertaking the different necessary activities to fulfill the requirements of the regulatory commission. This paper describes the main mechanisms included in NEI 99-03 Nuclear Energy Institute publication Control room Habitability Assessment guidance, to demonstrate and maintain Control room Habitability. In addition, in this article it Ds shown the theoretical principle of the test used to quantify air in-leakage in a control room envelope by using tracer gas techniques. The necessary activities to perform the initial in leakage testing are also put forward. Since 2006 Tecnatom, S. A. has performed the baseline testing in four Spanish Units, all of them with successful results. The rest of the Plants are scheduled to perform the tests during the second half of this year. Finally, this document summarises the more important aspects to be taken into account in the development of control room Habitability Programs, which are expected to ensure the integral maintenance of the Control room Envelope during the life a plant. (Author)

Deposition of silicon oxynitride films by low energy ion beam assisted nitridation at room temperature

Science.gov (United States)

Youroukov, S.; Kitova, S.; Danev, G.

2008-05-01

The possibility is studied of growing thin silicon oxynitride films by e-gun evaporation of SiO and SiO2 together with concurrent bombardment with low energy N2+ ions from a cyclotron resonance (ECR) source at room temperature of substrates. The degree of nitridation and oxidation of the films is investigated by means of X-ray spectroscopy. The optical characteristics of the films, their environmental stability and adhesion to different substrates are examined. The results obtained show than the films deposited are transparent. It is found that in the case of SiO evaporation with concurrent N2+ ion bombardment, reactive implantation of nitrogen within the films takes place at room temperature of the substrate with the formation of a new silicon oxynitride compound even at low ion energy (150-200 eV).

Construindo a interação entre o gerenciamento de projetos e a resource-based view-rbv

Directory of Open Access Journals (Sweden)

Francisco Carlos Cobaito

2014-08-01

Full Text Available Pode-se considerar que a abordagem da teoria do RBV (Resource-based View, e o ponto de vista da teoria de Gerenciamento de projetos apresentam pressupostos distintos. Enquanto a primeira se volta para o modo como os recursos se comportam para a criação e sustentação de vantagem competitiva, a segunda se dirige aos recursos e competências necessários para maximizar a probabilidade de sucesso de um empreendimento. Ambas, contudo, apoiam-se em pressupostos teóricos que identificam capacidades distintivas e competências essenciais nas organizações. Como objetivo exploram-se os elos entre estas duas teorias. Baseado em um estudo de caso foi possível identificar quais são e como os recursos de valor, sob a ótica da RBV, atuam simultânea e sinergicamente no Gerenciamento de projetos.

Room temperature Cu-Cu direct bonding using surface activated bonding method

International Nuclear Information System (INIS)

Kim, T.H.; Howlader, M.M.R.; Itoh, T.; Suga, T.

2003-01-01

Thin copper (Cu) films of 80 nm thickness deposited on a diffusion barrier layered 8 in. silicon wafers were directly bonded at room temperature using the surface activated bonding method. A low energy Ar ion beam of 40-100 eV was used to activate the Cu surface prior to bonding. Contacting two surface-activated wafers enables successful Cu-Cu direct bonding. The bonding process was carried out under an ultrahigh vacuum condition. No thermal annealing was required to increase the bonding strength since the bonded interface was strong enough at room temperature. The chemical constitution of the Cu surface was examined by Auger electron spectroscope. It was observed that carbon-based contaminations and native oxides on copper surface were effectively removed by Ar ion beam irradiation for 60 s without any wet cleaning processes. An atomic force microscope study shows that the Ar ion beam process causes no surface roughness degradation. Tensile test results show that high bonding strength equivalent to bulk material is achieved at room temperature. The cross-sectional transmission electron microscope observations reveal the presence of void-free bonding interface without intermediate layer at the bonded Cu surfaces

Control room and ergonomic design

International Nuclear Information System (INIS)

Hinz, W.

1984-01-01

The important basis for the configuration of the control room of a nuclear power station is the concept for controlling a fault and that for controlling normal operation. The tasks resulting from this for the control room personnel are decided by the control room concept. In this configuration process (from the division of process control tasks between the system components operators and control technology to the configuration of individual means of operation) the characteristics and capabilities of the personnel, which are subject to special requirements as regards their qualifications, are observed. New concepts which are only now technically feasible are therefore being developed for information processing and display, in order to give the personnel a better oversight of the state and trends of the plant. (orig./DG) [de

Competitive Advantage in Intercollegiate Athletics: Role of Intangible Resources.

Science.gov (United States)

Won, Doyeon; Chelladurai, Packianathan

2016-01-01

The present research explored the dynamics of competitive advantages in intercollegiate athletics by investigating the contribution of intangible resources (i.e., athletic and academic reputations) on the generation of more tangible resources (i.e., human and financial resources), which in turn influence the athletic performance (i.e., winning record) and academic performance (i.e., graduation rates), and gender equity. The research was based entirely on archival data of 324 NCAA Division I member institutions. The results of the SEM supported the study's basic arguments that tangible resources are the sources of competitive advantages in Division I intercollegiate athletics, and that intangible resources contribute to the generation of tangible resources.

A Resource Perspective on the Work-Home Interface: The Work-Home Resources Model

Science.gov (United States)

ten Brummelhuis, Lieke L.; Bakker, Arnold B.

2012-01-01

The objective of this article is to provide a theoretical framework explaining positive and negative work-home processes integrally. Using insights from conservation of resources theory, we explain how personal resources (e.g., time, energy, and mood) link demanding and resourceful aspects of one domain to outcomes in the other domain. The…

The geothermal resource in Dominica : from the class room to the fieldwork

Science.gov (United States)

Olivia, Urity

2014-05-01

In Martinique and more generally in the Caribbean area, the Global warming is not only a topic you can read about in a scientific article but a true issue in the everyday life of the inhabitants. Many effects of the increase of the sea level or the erosion can be observed in the environment. For example, beaches are being destroyed, frightening buildings built on the seafront. This is not only an environmental issue but a touristic and economical one. By the way it is a problem to give a new home to these inhabitants who are now losing their houses. So, with their limited territory and their economy depending on tourism, the islands of the Lesser Antilles have a big challenge which is to find some solutions to minimize the effects of the Global warming on their populations. Anyway, anthropic activities and particularly the using of fossil fuels are named to be responsible for a big part of the climate changes. Knowing this allows us to understand that the Caribbean countries have to develop renewable energies. Guadeloupe and Dominica are two good examples of these islands, where the politicians have already decided to use sustainable energies. They use geothermal energy and hydroelectricity to provide to the families' needs. In this way, the Dominican government, with finances from The European Union, Guadeloupe and Martinique decided to explore the geothermal resource in the island and to build a plant in the area of Roseau Valley. Therefore the students and I, we have decided to study the geology of Dominica in order to find the origin of the geothermal resource and to get more information about the geothermal power plant project. Furthermore, we wanted to understand how this resource is used by the locals and to determine the impact of the presence of the future plant in the chosen sites. In the poster to come, I have chosen to introduce the "journey in Dominica" and the fieldwork that I have realized with my students of upper sixth form. The poster will focus

Economic Observation in 3Q E-business Fight - According to Analysis of Resource Allocation and Contract

Science.gov (United States)

Kuang, Ruihu; Chen, Zeming; Kuang, Juchi

Based on relation of resource allocation and marginal benefit of e-commence provider, both of origin and essence of the 3Q e-business fight were analyzed; and then contents of the contract between e-business company and users were elaborated. Moreover, liability for Qihoo's breach of the contract in 3Q e-business fight was discussed. Analysis of the contract indicated that blame of infringing on privacy of users from public, media or even a law professor for Tengxun Company is not exactly justicial. Some controversial rules which are not fit for usual practices in the QQ contract such as narrow definition of privacy were found out, whose reason lies in no relevant e-business standards or rules in our country. In the end, this passage points out that actions of government who intervened in market operations of Tengxun Company and QQ Company are inappropriate and unnecessary. Thus, responsibility for facing up to incomplete market rules of e-commence lies with government and government should strengthen market supervision by legislation so as to guide healthy development of e-business market, which is a key lesson we learn from the 3Q e-business fight.

New technologies for control room habitability assessment

International Nuclear Information System (INIS)

Lahti, G.P.; Muraida, J.E.; Perchiazzi, W.T.; Harden, P.A.

1994-01-01

Older nuclear power plants typically considered only a nominal amount of unfiltered inleakage (typically 10 cfm) impacting their postaccident control room habitability. However, recent measurements of unfiltered inleakage show values in excess of the nominal 10 cfm. A reassessment for two of these ''older'' stations has been completed recently to show that the measured inleakage did not jeopardize the safety of the control room occupants. Recent concerns at the Zion Station and the Palisades Station about control room habitability in the event of a loss-of-coolant accident have led to an extensive effort to increase control room habitability margin. The heating, ventilating and air-conditioning (HVAC) system servicing each of the control rooms has the potential for unfiltered in-leakage through many locations. For example, at the Palisades Station, the current limiting control room habitability analysis allows for 25 cfm unfiltered in-leakage through its normal outside air intake louvered isolation dampers during emergency mode into the control room envelope. This leakage value was not thought to be achievable with the existing as-built configuration. Repairing the system was considered a potential solution; however, this would be costly and could negatively affect plant operation. In addition, the system would still be required to meet the low specified unfiltered in-leakage. An alternate approach was to review the analysis and reassess the most important parameters. The key effort was to determine the atmospheric dispersion factors (χ/Qs) through wind tunnel tests using scale models of the stations. The results of the wind tunnel testing could yield more realistic χ/Qs for control room habitability than previously employed methods. The wind tunnel study options were selected based on their ease of implementation, realistic results, and low cost. More importantly, the results of the studies would allow more realistic values of unfiltered inleakage

Room Temperature Stable PspA-Based Nanovaccine Induces Protective Immunity

Directory of Open Access Journals (Sweden)

Danielle A. Wagner-Muñiz

2018-03-01

Full Text Available Streptococcus pneumoniae is a major causative agent of pneumonia, a debilitating disease particularly in young and elderly populations, and is the leading worldwide cause of death in children under the age of five. While there are existing vaccines against S. pneumoniae, none are protective across all serotypes. Pneumococcal surface protein A (PspA, a key virulence factor of S. pneumoniae, is an antigen that may be incorporated into future vaccines to address the immunological challenges presented by the diversity of capsular antigens. PspA has been shown to be immunogenic and capable of initiating a humoral immune response that is reactive across approximately 94% of pneumococcal strains. Biodegradable polyanhydrides have been studied as a nanoparticle-based vaccine (i.e., nanovaccine platform to stabilize labile proteins, to provide adjuvanticity, and enhance patient compliance by providing protective immunity in a single dose. In this study, we designed a room temperature stable PspA-based polyanhydride nanovaccine that eliminated the need for a free protein component (i.e., 100% encapsulated within the nanoparticles. Mice were immunized once with the lead nanovaccine and upon challenge, presented significantly higher survival rates than animals immunized with soluble protein alone, even with a 25-fold reduction in protein dose. This lead nanovaccine formulation performed similarly to protein adjuvanted with Alum, however, with much less tissue reactogenicity at the site of immunization. By eliminating the free PspA from the nanovaccine formulation, the lead nanovaccine was efficacious after being stored dry for 60 days at room temperature, breaking the need for maintaining the cold chain. Altogether, this study demonstrated that a single dose PspA-based nanovaccine against S. pneumoniae induced protective immunity and provided thermal stability when stored at room temperature for at least 60 days.

The radiation dose dilemma in the hybrid operating room

NARCIS (Netherlands)

de Ruiter, QMB

2016-01-01

The of the hybrid Operation room (an operation room combined with advanced radiological X-ray equipment) is gaining popularity, as it is now the preferred room to perform (complex) endovascular aortic procedures. The fixed C-arms equipped in these rooms make it possible to gain very high image

Nuclear reactor control room construction

International Nuclear Information System (INIS)

Lamuro, R.C.; Orr, R.

1993-01-01

A control room for a nuclear plant is disclosed. In the control room, objects labelled 12, 20, 22, 26, 30 in the drawing are no less than four inches from walls labelled 10.2. A ceiling contains cooling fins that extend downwards toward the floor from metal plates. A concrete slab is poured over the plates. Studs are welded to the plates and are encased in the concrete. 6 figures

Human-Like Room Segmentation for Domestic Cleaning Robots

Directory of Open Access Journals (Sweden)

David Fleer

2017-11-01

Full Text Available Autonomous mobile robots have recently become a popular solution for automating cleaning tasks. In one application, the robot cleans a floor space by traversing and covering it completely. While fulfilling its task, such a robot may create a map of its surroundings. For domestic indoor environments, these maps often consist of rooms connected by passageways. Segmenting the map into these rooms has several uses, such as hierarchical planning of cleaning runs by the robot, or the definition of cleaning plans by the user. Especially in the latter application, the robot-generated room segmentation should match the human understanding of rooms. Here, we present a novel method that solves this problem for the graph of a topo-metric map: first, a classifier identifies those graph edges that cross a border between rooms. This classifier utilizes data from multiple robot sensors, such as obstacle measurements and camera images. Next, we attempt to segment the map at these room–border edges using graph clustering. By training the classifier on user-annotated data, this produces a human-like room segmentation. We optimize and test our method on numerous realistic maps generated by our cleaning-robot prototype and its simulated version. Overall, we find that our method produces more human-like room segmentations compared to mere graph clustering. However, unusual room borders that differ from the training data remain a challenge.

Room temperature creep in metals and alloys

Energy Technology Data Exchange (ETDEWEB)

Deibler, Lisa Anne [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Materials Characterization and Performance

2014-09-01

Time dependent deformation in the form of creep and stress relaxation is not often considered a factor when designing structural alloy parts for use at room temperature. However, creep and stress relaxation do occur at room temperature (0.09-0.21 T_m for alloys in this report) in structural alloys. This report will summarize the available literature on room temperature creep, present creep data collected on various structural alloys, and finally compare the acquired data to equations used in the literature to model creep behavior. Based on evidence from the literature and fitting of various equations, the mechanism which causes room temperature creep is found to include dislocation generation as well as exhaustion.

The Virtual Dressing Room

DEFF Research Database (Denmark)

Holte, Michael Boelstoft

2013-01-01

This paper presents a review of recent developments and future perspectives, addressing the problem of creating a virtual dressing room. First, we review the current state-of-the-art of exiting solutions and discuss their applicability and limitations. We categorize the exiting solutions into three...... kinds: (1) virtual real-time 2D image/video techniques, where the consumer gets to superimpose the clothes on their real-time video to visualize themselves wearing the clothes. (2) 2D and 3D mannequins, where a web-application uses the body measurements provided by the customer, to superimpose...... and their demands to a virtual dressing room....

Control room design and human factors using a virtual reality based tool for design, test and training

International Nuclear Information System (INIS)

Lirvall, Peter

1998-02-01

This report describes a user-centred approach to control room design adopted by IFE for the nuclear industry. The novelty of this approach is the development of a Control Room Philosophy, and the use of Virtual Reality (VR) technology as a tool in the design process, integrated with a specially developed Design Documentation System (DDS) and a process display prototyping tool PICASSO-3. The control room philosophy identifies all functional aspects of a control centre, to define the baseline principles and guidelines for the design. The use of VR technology enables end-users of the control room design (e.g. control room operators) to specify their preferred design of the new control room, and to replace the need for a physical mock-up to test and evaluate the proposed design. The DDS, integrated with the VR design tool, guides the control room operators, through a structured approach, to document the proposed design in a complete design specification. The VR tool, specially developed by IFE, is called the VR based Design, Test and Training tool (VR DTandT). It is not only intended to visualise the design, but also to test and evaluate the design. When the design is implemented, the same model is re-used as a VR based training simulator for operators. A special feature in the VR DTandT tool is that the verification and validation (VandV) tests, concerning human factors, are according to the regulative standards for nuclear control rooms

Low frequency sound field control in rectangular listening rooms using CABS (Controlled Acoustic Bass System) will also reduce sound transmission to neighbor rooms

DEFF Research Database (Denmark)

Nielsen, Sofus Birkedal; Celestinos, Adrian

2011-01-01

Sound reproduction is often taking place in small and medium sized rectangular rooms. As rectangular rooms have 3 pairs of parallel walls the reflections at especially low frequencies will cause up to 30 dB spatial variations of the sound pressure level in the room. This will take place not only...... at resonance frequencies, but more or less at all frequencies. A time based room correction system named CABS (Controlled Acoustic Bass System) has been developed and is able to create a homogeneous sound field in the whole room at low frequencies by proper placement of multiple loudspeakers. A normal setup...... from the rear wall, and thereby leaving only the plane wave in the room. With a room size of (7.8 x 4.1 x 2.8) m. it is possible to prevent modal frequencies up to 100 Hz. An investigation has shown that the sound transmitted to a neighbour room also will be reduced if CABS is used. The principle...

7 CFR 58.620 - Freezing and packaging rooms.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Freezing and packaging rooms. 58.620 Section 58.620 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards....620 Freezing and packaging rooms. The rooms used for freezing and packaging frozen desserts shall be...

HAMMLAB 1999 experimental control room: design - design rationale - experiences

International Nuclear Information System (INIS)

Foerdestroemmen, N. T.; Meyer, B. D.; Saarni, R.

1999-01-01

A presentation of HAMMLAB 1999 experimental control room, and the accumulated experiences gathered in the areas of design and design rationale as well as user experiences. It is concluded that HAMMLAB 1999 experimental control room is a realistic, compact and efficient control room well suited as an Advanced NPP Control Room (ml)

[Neonatological emergencies in delivery room] [Article in Italian] • Il neonatologo ed alcune emergenze in sala parto

Directory of Open Access Journals (Sweden)

Antonio Boldrini

2014-01-01

Full Text Available Introduction: In the delivery room the neonatologist may deal with emergencies, not always predictable by pre-natal diagnosis. Among these dangerous situations, we include: i extremely preterm birth of a newborn very/extremely low birth weight and ii shoulder dystocia in term newborns. We will discuss in details these two clinical scenarios. Methods: We reviewed the main recent papers about resuscitation of very/extremely low birth weight preterm newborns and about dystocia of shoulder reported in PubMed database. After that, we compared reported results with practice in our Unit and discussed the topics considering strategies to optimize the results and minimizing possible errors. Discussion and conclusions: In our opinion the optimization of clinical practice in Neonatology should be based on: i national or international recommendations drawn up by commissions or study groups of experts, on the basis of scientific evidence, ii local department protocols, in order to standardize staff interventions within the same unit; iii ongoing training of doctors, nurses and midwives, through simulation sessions and CRM (Crisis Resources Management. As regards shoulder dystocia, The Tuscan Group for Clinical Risk Management drawn a poster to be showed in every delivery room, in order to allow the staff to rapidly remember the correct clinical interventions. On the other hand, as regards ventilatory preterm newborns strategies, the Centro di Formazione e Simulazione NINA is working on a project of a mechatronich simulator for staff training (MERESSINA. Articoli Selezionati del “3° Convegno Pediatrico del Medio Campidano” · Guspini · 25 Maggio 2013 Guest Editor: Roberto Antonucci

Room climate in large historical rooms. Raumklima in grossen historischen Raeumen; Heizungsart, Heizungsweise, Schadensentwicklung, Schadensverhinderung

Energy Technology Data Exchange (ETDEWEB)

Arendt, C

1993-01-01

The effects of different types of heating systems in large historical rooms on the room climate, the building and (to some extent) on humans are investigated. Starting from a theoretical analysis and available experimental reports, suitable objects (churches, theatres, festival and assembly halls) were selected in which a number of parameters were measured. From the results criteria were established for judging the different types of heating systems. (BWI). 181 figs.

SU-E-T-270: Optimized Shielding Calculations for Medical Linear Accelerators (LINACs).

Science.gov (United States)

Muhammad, W; Lee, S; Hussain, A

2012-06-01

The purpose of radiation shielding is to reduce the effective equivalent dose from a medical linear accelerator (LINAC) to a point outside the room to a level determined by individual state/international regulations. The study was performed to design LINAC's room for newly planned radiotherapy centers. Optimized shielding calculations were performed for LINACs having maximum photon energy of 20 MV based on NCRP 151. The maximum permissible dose limits were kept 0.04 mSv/week and 0.002 mSv/week for controlled and uncontrolled areas respectively by following ALARA principle. The planned LINAC's room was compared to the already constructed (non-optimized) LINAC's room to evaluate the shielding costs and the other facilities those are directly related to the room design. In the evaluation process it was noted that the non-optimized room size (i.e., 610 × 610 cm 2 or 20 feet × 20 feet) is not suitable for total body irradiation (TBI) although the machine installed inside was having not only the facility of TBI but the license was acquired. By keeping this point in view, the optimized INAC's room size was kept 762 × 762 cm 2. Although, the area of the optimized rooms was greater than the non-planned room (i.e., 762 × 762 cm 2 instead of 610 × 610 cm 2), the shielding cost for the optimized LINAC's rooms was reduced by 15%. When optimized shielding calculations were re-performed for non-optimized shielding room (i.e., keeping room size, occupancy factors, workload etc. same), it was found that the shielding cost may be lower to 41 %. In conclusion, non- optimized LINAC's room can not only put extra financial burden on the hospital but also can cause of some serious issues related to providing health care facilities for patients. © 2012 American Association of Physicists in Medicine.

Identifying state resources and support programs on e-government websites for persons with intellectual and developmental disabilities.

Science.gov (United States)

Fisher, Kathleen M; Peterson, Justin D; Albert, Jon D

2015-01-01

This descriptive cross-sectional study identified resources and programs that are available nationwide on the Internet to support individuals and families with intellectual and developmental disabilities (I/DD), with a focus on intellectual disability. This evaluation included easily identifiable information on specific resources and highlighted unique programs found in individual states that were linked from e-government websites. Researchers documented the ease of access and available information for all 50 states and the District of Columbia. A number of disparities and areas for improvement were recorded for states and I/DD websites. The researchers conclude that a number of additional health and support services will be needed to address the growing needs of this vulnerable population.

Determination of radon in housing rooms

International Nuclear Information System (INIS)

Steger, F.; Sorantin, H.; Kozuh-Schneeberger, J.; Lovranich, E.; Khademi, B.

1988-03-01

Radon concentration in 171 apartments with 503 rooms in and around Vienna was measured by a passive measuring system. Polycarbonate foils were exposed during 3 months; the nuclear tracks were visualized by electro-chemical method and evaluated. In housing- and sleeping rooms the mean concentration was 1,03 pCi/l, in cellars 2,15 pCi/l. The equivalent dosis, with 1,03 pCi/l was estimated to 90 mrem/a. At the same time the external radiation dose in the same rooms was measured by TL dosimeters and the dose estimated is again 90 mrem/a. 34 refs., 16 figs., 4 tabs. (qui)

Guidelines for control room systems design. Working material. Report

International Nuclear Information System (INIS)

1993-01-01

This report contains comprehensive technical and methodological information and recommendations for the benefit of Member States for advice and assistance in ''NPP control room systems'' design backfitting existing nuclear power plants and design for future stations. The term ''Control Room Systems'' refers to the entire human/machine interface for the nuclear stations - including the main control room, back-ups control room and the emergency control rooms, local panels, technical support centres, operating staff, operating procedures, operating training programs, communications, etc. Refs, figs and tabs

Externality costs by resource. E. Renewable generation resources

International Nuclear Information System (INIS)

Anon.

1991-01-01

This chapter describes the environmental impacts associated with operation of renewable energy technologies. Renewable energy technologies currently supply 8% of US total energy usage and that figure is certain to grow. The rate of growth will depend heavily on the availability of research and development funds, and could reach 28% of US energy demands by 2030. Renewable generation resources include hydroelectric development, solar energy technologies, wind conversion facilities, and biomass fueled generation. A task force of personnel from five national laboratories recently concluded that renewable energy technologies generally have lower environmental impacts than do fossil fuel energy systems. The task force also stated that a comprehensive and comparative analysis of environmental impacts is needed and would strengthen the National Energy Strategy. This chapter summarizes some of the available literature on costing the environmental externalities associated with hydro, solar, wind, and biomass facilities. The less prevalent renewable energy technologies, including geothermal and ocean energy technologies, were not researched. The cost ranges identified are summarized in Table 1. The Table does not include a value for hydroelectric energy. The one study which attempted to value hydroelectric externalities was highly site-specific and has been criticized for having vastly overstated the value of the externalities

Translating research into practice: evaluation of an e-learning resource for health care professionals to provide nutrition advice and support for cancer survivors.

Science.gov (United States)

Murphy, Jane; Worswick, Louise; Pulman, Andy; Ford, Grainne; Jeffery, Jaana

2015-01-01

Nurses and other allied health professionals are in a key position to provide appropriate and consistent advice on nutritional issues to support cancer survivors. However gaps in their nutrition knowledge and education warrant the need for enhanced learning as part of their Continued Professional Development (CPD). In the UK there are currently no formally recognised nutrition education programmes. Therefore e-learning offers a solution to provide flexible learning to target this need. This study aimed to develop and evaluate the efficacy of a freely available, internet-based learning resource, for nurses and allied health professionals who provide nutrition, diet and lifestyle advice for cancer survivors. It sought to explore the attitudes and conceptions of the resource and current knowledge base of those involved in the care pathway for cancer survivors. The design and development of the e-learning resource were informed by the best available research and policy evidence and in a format to facilitate on-line learning. A robust evaluation strategy incorporated focus groups and telephone interviews to gain in depth insights into the experiences of using the resource. Themes included 'Plugging a Gap' which shows an improved knowledge base for nutrition. Information was 'All in One Place' showing that the resource was valued as being within a 'trusted' organisation. 'Everyone Benefits' illustrates how learners felt that the resource provided them with an evidence base, whilst the 'Current and Live' theme captured how professionals felt about the information being up-to-date. The project has shown the benefits of interprofessional working to develop an e-learning resource for Health Care Professionals to support cancer survivors in following healthier lifestyles. Positive attitudes and potential improvements in the knowledge base and changes for professional practice were demonstrated. Further research is required to gauge sustained impact in the work environment by

eMental health experiences and expectations: a survey of youths' Web-based resource preferences in Canada.

Science.gov (United States)

Wetterlin, Felicia M; Mar, Marissa Y; Neilson, Erika K; Werker, Gregory R; Krausz, Michael

2014-12-17

Due to the high prevalence of psychological disorders and the lack of access to care among Canadian youth, the development of accessible services is increasingly important. eMental Health is an expanding field that may help to meet this need through the provision of mental health care using technology. The primary goals of the study are to explore youth experiences with traditional and online mental health resources, and to investigate youth expectations for mental health websites. A Web-based survey containing quantitative and qualitative questions was delivered to youth aged 17-24 years. Participants were surveyed to evaluate their use of mental health resources as well as their preferences for various components of a potential mental health website. A total of 521 surveys were completed. Most participants (61.6%, 321/521) indicated that they had used the Internet to seek information or help for feelings they were experiencing. If they were going through a difficult time, 82.9% (432/521) of participants were either "somewhat likely" or "very likely" to use an information-based website and 76.8% (400/521) reported that they were either "somewhat unlikely" or "very unlikely" to visit social media websites for information or help-seeking purposes during this time. Most (87.7%, 458/521) participants rated their online privacy as very important. Descriptions of interventions and treatments was the most highly rated feature to have in a mental health-related website, with 91.9% (479/521) of participants regarding it as "important" or "very important". When presented a select list of existing Canadian mental health-related websites, most participants had not accessed any of the sites. Of the few who had, the Canadian Mental Health Association website was the most accessed website (5.8%, 30/521). Other mental health-related websites were accessed by only 10.9% of the participants (57/521). The findings suggest that despite interest in these tools, current eMental Health

New heuristics for planning operating rooms.

NARCIS (Netherlands)

Molina-Pariente, J.M.; Hans, Elias W.; Framinan, J.M.; Gomez-Cia, T.

2015-01-01

We tackle the operating room planning problem of the Plastic Surgery and Major Burns Specialty of the University Hospital “Virgen del Rocio” in Seville (Spain). The decision problem is to assign an intervention date and an operating room to a set of surgeries on the waiting list, minimizing access

Deposition of silicon oxynitride films by low energy ion beam assisted nitridation at room temperature

Energy Technology Data Exchange (ETDEWEB)

Youroukov, S; Kitova, S; Danev, G [Central Laboratory of Photoprocesses, Bulgarian Academy of Sciences, Acad. G. Bonchev Str., Bl. 109, 113 Sofia (Bulgaria)], E-mail: skitova@clf.bas.bg

2008-05-01

The possibility is studied of growing thin silicon oxynitride films by e-gun evaporation of SiO and SiO{sub 2} together with concurrent bombardment with low energy N{sub 2}{sup +} ions from a cyclotron resonance (ECR) source at room temperature of substrates. The degree of nitridation and oxidation of the films is investigated by means of X-ray spectroscopy. The optical characteristics of the films, their environmental stability and adhesion to different substrates are examined. The results obtained show than the films deposited are transparent. It is found that in the case of SiO evaporation with concurrent N{sub 2}{sup +} ion bombardment, reactive implantation of nitrogen within the films takes place at room temperature of the substrate with the formation of a new silicon oxynitride compound even at low ion energy (150-200 eV)

e-Cluster Building and Using for Nuclear Industry Human Resources

International Nuclear Information System (INIS)

Hur, Jung Hoon; Suh, Jang Soo

2009-01-01

In line with its industry support policy, KHNP provides training courses for small and medium sized companies within the nuclear sector. The courses cover three main areas; technical development, market expansion and human resource and finance. They are provided in traditional classroom settings and on-line. Employees from small and medium sized companies can take any of the available courses according to company and individual training and development requirements. While the training and development opportunities serve a role in the growth and development of skills and capabilities industry-wide, KHNP also sees the involvement of a wide range of nuclear industry participants in the program as a means of developing a safety consensus that addresses both operational and social safety concerns. The purpose of this paper is to outline the successes of the KHNP industry training support program to date and to propose the development of an e-Cluster model. This model envisages the development of a nuclear industry. It will provide a means for sharing information and developing and maintaining industry-wide technical, management and safety standards

Clean room actuators

Energy Technology Data Exchange (ETDEWEB)

Higuchi, Toshiro

1987-06-01

This report explains on the present status of the clean room actuators including the author's research results. In a clean room, there exists a possibility of dust generation, even when a direct human work is eliminated by the use of robots or automatic machines, from the machines themselves. For this, it is important to develop such clean robots and transfer/positioning mechanism that do not generate dusts, and to develop an actuator and its control technique. Topics described in the report are as follows: 1. Prevention of dust diffusion by means of sealing. 2. Elimination of mechanical contact (Linear induction motor and pneumatic float, linear motor and magnetic attraction float, linear motor and air bearing, and magnetic bearing). 3. Contactless actuator having a positioning mechanism (Use of linear step motor and rotary contactless actuator). (15 figs, 11 refs)

Control room habitability study - findings and recommendations

International Nuclear Information System (INIS)

Driscoll, J.W.

1987-01-01

The Advisory Committee on Reactor Safeguards (ACRS) has raised a number of concerns related to control room habitability and has recommended actions which they believe could alleviate these concerns. As a result of the ACRS's concerns, the US Nuclear Regulatory Commission's (NRC) Office of Nuclear Reactor Regulation (NRR) in conjunction with the Offices of Research and Inspection and Enforcement, and the NRC regional offices, embarked upon a program to reevaluate Control Room Habitability. Argonne National Laboratory was contracted by the NRC to perform a Control Room Habitability Study on twelve licensed power reactors. The plants selected for the study were chosen based upon architect engineer, nuclear steam system supplier, utility, and plant location. The major findings of this study are included in this report along with generic recommendations of the review team that apply to control room HVAC systems. Although the study is not complete, at the time of publication of this report, the results obtained to date should be useful to persons responsible for Control Room Habitability in evaluating their own systems

Antitumor effect of triptolide in T-cell lymphoblastic lymphoma by inhibiting cell viability, invasion, and epithelial–mesenchymal transition via regulating the PI3K/AKT/mTOR pathway

Directory of Open Access Journals (Sweden)

Huang Y

2018-02-01

Full Text Available Yan Huang, Sun Wu, Yuan Zhang, Lihua Wang, Yan Guo Department of Hematology, The First Affiliated Hospital of Xinxiang Medical University, Xinxiang, People’s Republic of China Introduction: T-cell lymphoblastic lymphoma (T-LBL is a widely disseminated disease worldwide. Triptolide (TPL is purified from Chinese herb and displays anti-inflammatory, anti-fertility, anti-tumor and immunosuppressive effects. Materials and methods: Here, in vitro and in vivo experiments were conducted to investigate the anti-tumor effect of TPL treatment in T-LBL and the potential mechanism in T-LBL progression. Results: TPL inhibited cell proliferation of T-LBL cells (Jurkat cells and Molt-3 cells in a dose-dependent manner. Flow cytometry analysis showed that cell apoptosis rate was increased by TPL treatment. TPL also up-regulated the expression of Caspase-3, Bax and down-regulated the expression of Bcl-2, indicating that TPL promoted apoptosis in Jurkat cells. Moreover, TPL inhibited invasion ability of Jurkat cells and down-regulated the expression of MMP-3 and MMP-9 in a dose-dependent manner. The expression of Snail, Slug, Twist and Integrin αVβ6 was decreased and the expression of E-cadherin was increased by TPL treatment, indicating that TPL inhibited EMT of Jurkat cells. Apart from that, TPL treatment attenuated the phoslevels of PI3K, Akt and mTOR and suppressed AKT activation compared with control group, suggesting that TPL inhibited PI3K/Akt/mTOR signal pathway in T-LBL. In vivo experiments showed that TPL inhibited tumor growth of T-LBL and promoted apoptosis of tumor cells. The expression of PCNA, Bcl-2, Snail, p-PI3K, p-Akt and mTOR was suppressed by TPL in a dose-dependent manner, suggesting that TPL suppressed tumor growth and promoted apoptosis of tumor cells by inhibiting PI3K/Akt/mTOR signal pathway in T-LBL. Conclusion: In conclusion, TPL exerted anti-tumor effect in T-LBL by inhibiting cell viability, invasion and EMT via regulating the PI3K

Control room human engineering influences on operator performance

International Nuclear Information System (INIS)

Finlayson, F.C.

1977-01-01

Three general groups of factors influence operator performance in fulfilling their responsibilities in the control room: (1) control room and control system design, informational data displays (operator inputs) as well as control board design (for operator output); (2) operator characteristics, including those skills, mental, physical, and emotional qualities which are functions of operator selection, training, and motivation; (3) job performance guides, the prescribed operating procedures for normal and emergency operations. This paper presents some of the major results of an evaluation of the effect of human engineering on operator performance in the control room. Primary attention is given to discussion of control room and control system design influence on the operator. Brief observations on the influences of operator characteristics and job performance guides (operating procedures) on performance in the control room are also given. Under the objectives of the study, special emphasis was placed on the evaluation of the control room-operator relationships for severe emergency conditions in the power plant. Consequently, this presentation is restricted largely to material related to emergency conditions in the control room, though it is recognized that human engineering of control systems is of equal (or greater) importance for many other aspects of plant operation

7 CFR 58.212 - Hopper or dump room.

Science.gov (United States)

2010-01-01

....212 Hopper or dump room. A separate room shall be provided for the transfer of bulk dry dairy products to the hoppers and conveyors which lead to the fillers. This room shall meet the same requirements... transfer of dry dairy products from portable bulk bins will be accepted if gasketed surfaces or direct...

7 CFR 58.413 - Cutting and packaging rooms.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Cutting and packaging rooms. 58.413 Section 58.413....413 Cutting and packaging rooms. When small packages of cheese are cut and wrapped, separate rooms shall be provided for the cleaning and preparation of the bulk cheese and for the cutting and wrapping...

Calculation of Appropriate Minimum Size of Isolation Rooms based on Questionnaire Survey of Experts and Analysis on Conditions of Isolation Room Use

Science.gov (United States)

Won, An-Na; Song, Hae-Eun; Yang, Young-Kwon; Park, Jin-Chul; Hwang, Jung-Ha

2017-07-01

After the outbreak of the MERS (Middle East Respiratory Syndrome) epidemic, issues were raised regarding response capabilities of medical institutions, including the lack of isolation rooms at hospitals. Since then, the government of Korea has been revising regulations to enforce medical laws in order to expand the operation of isolation rooms and to strengthen standards regarding their mandatory installation at hospitals. Among general and tertiary hospitals in Korea, a total of 159 are estimated to be required to install isolation rooms to meet minimum standards. For the purpose of contributing to hospital construction plans in the future, this study conducted a questionnaire survey of experts and analysed the environment and devices necessary in isolation rooms, to determine their appropriate minimum size to treat patients. The result of the analysis is as follows: First, isolation rooms at hospitals are required to have a minimum 3,300mm minor axis and a minimum 5,000mm major axis for the isolation room itself, and a minimum 1,800mm minor axis for the antechamber where personal protective equipment is donned and removed. Second, the 15 ㎡-or-larger standard for the floor area of isolation rooms will have to be reviewed and standards for the minimum width of isolation rooms will have to be established.

Clinic exam room design: present and future.

Science.gov (United States)

Freihoefer, Kara; Nyberg, Gary; Vickery, Christine

2013-01-01

This article aims to deconstruct various design qualities and strategies of clinic exam rooms, and discuss how they influence users' interaction and behavior in the space. Relevant literature supports the advantages and disadvantages of different design strategies. Annotated exam room prototypes illustrate the design qualities and strategies discussed. Advancements in technology and medicine, along with new legislative policies, are influencing the way care providers deliver care and ultimately clinic exam room designs. The patient-centered medical home model has encouraged primary care providers to make patients more active leaders of their health plan which will influence the overall functionality and configuration of clinic exam rooms. Specific design qualities discussed include overall size, location of doors and privacy curtains, positioning of exam tables, influence of technology in the consultation area, types of seating, and placement of sink and hand sanitizing dispensers. In addition, future trends of exam room prototypes are presented. There is a general lack of published evidence to support design professionals' design solutions for outpatient exam rooms. Future research should investigate such topics as the location of exam tables and privacy curtains as they relate to patient privacy; typical size and location of consultation table as it relates to patient connection and communication; and placement of sinks and sanitization dispensers as they relate to frequency and patterns of usage. Literature review, outpatient, technology, visual privacy.

Room-temperature annealing of Si implantation damage in InP

International Nuclear Information System (INIS)

Akano, U.G.; Mitchell, I.V.

1991-01-01

Spontaneous recovery at 295 K of Si implant damage in InP is reported. InP(Zn) and InP(S) wafers of (100) orientation have been implanted at room temperature with 600 keV Si + ions to doses ranging from 3.6x10 11 to 2x10 14 cm -2 . Room-temperature annealing of the resultant damage has been monitored by the Rutherford backscattering/channeling technique. For Si doses ≤4x10 13 cm -2 , up to 70% of the initial damage (displaced atoms) annealed out over a period of ∼85 days. The degree of recovery was found to depend on the initial level of damage. Recovery is characterized by at least two time constants t 1 2 ∼100 days. Anneal rates observed between 295 and 375 K are consistent with an activation energy of 1.2 eV, suggesting that the migration of implant-induced vacancies is associated with the reordering of the InP lattice

Operating Room Utilization at Frederick Memorial Hospital

National Research Council Canada - National Science Library

Edwards, Jonathan A

2007-01-01

.... A logistical regression analysis was used to identify the impact of variables on operating room utilization rates and therefore help explain how or why some operating rooms incurred higher utilization rates than others...

Assessment of vocal intensity in lecturers depending on acoustic properties of lecture rooms

Directory of Open Access Journals (Sweden)

Witold Mikulski

2015-08-01

Full Text Available Background: Lombard’s effect increases the level of vocal intensity in the environment, in which noise occurs. This article presents the results of the author’s own study of vocal intensity level and A-weighted sound pressure level of background noise during normal lectures. The aim of the study was to define whether above-mentioned parameters depend on acoustic properties of rooms (classrooms or lecture rooms and to define how many lectors speak with raised voice. Material and Methods: The study was performed in a group of 50 teachers and lecturers in 10 classrooms with cubature of 160–430 m3 and reverberation time of 0.37–1.3 s (group A consisted of 3 rooms which fulfilled, group B consisted of 3 rooms which almost fulfilled and group C consisted of 4 rooms which did not fulfill criteria based on reverberation time (maximum permissible value is 0.6–0.8 s according to PN-B-02151-4:2015. Criteria of raising voice were based on vocal intensity level (maximum value: 65 dB according to EN ISO 9921:2003. The values of above-mentioned parameters were determined from modes of A-weighted sound pressure level distributions during lectures. Results: Great differentiation of vocal intensity level between lectors was found. In classrooms of group A lectors were not using raised voice, in group B – 21%, and in group C – 60% of lectors were using raised voice. Conclusions: It was observed that acoustic properties of classrooms (defined by reverberation time exert their effect on lecturer’s vocal intensity level (i.e., raising voice, which may contribute to the increased risk of vocal tract illnesses. The occurrence of Lombard’s effect in groups of teachers and lecturers, conducting lectures in rooms, was evidenced. Med Pr 2015;66(4:487–496

Control room habitability study: findings and recommendations

International Nuclear Information System (INIS)

Driscoll, J.W.

1986-01-01

The Advisory Committee on Reactor Safeguards (ACRS) has raised a number of concerns related to control room habitability and has recommended actions which they believe could alleviate these concerns. As a result of the ACRS's concerns, the US Nuclear Regulatory Commission's (NRC) Office of Nuclear Reactor Regulation (NRR) in conjunction with the Offices of Research and Inspection and Enforcement, and the NRC regional offices, embarked upon a program to reevaluate Control Room Habitability. Argonne National Laboratory was contracted by the NRC to perform a Control Room Habitability Study on twelve licensed power reactors. The plants selected for the study were chosen based upon architect engineer, nuclear steam system supplier, utility, and plant location. Participants in the study review the plant design as contained in the Updated Safety Analysis Report, Technical Specifications, Three Mile Island action item III.D.3.4 submittal on Control Room Habitability, NRC staff evaluation of the III.D.3.4 submittal, appropriate plant operating procedures, system drawings, and significant Licensee Event Reports on Loss of Cooling to the Control Room Envelope. A two-day visit is then made to the plant to determine if the as-built systems are built, operated, and surveillance performed as described in the documentation reviewed prior to the visit. The major findings of this study are included in this report along with generic recommendations of the review team that apply to control room HVAC systems. Although the study is not complete, at the time of publication of this report, the results obtained to date should be useful to persons responsible for Control Room Habitability in evaluating their own systems

Multi-bed patient room architectural evaluation

Directory of Open Access Journals (Sweden)

Evangelia Sklavou

2016-12-01

Full Text Available Introduction: Leveraging the physical environment’s merits is crucial in healthcare settings towards fostering sustainable healing conditions. In the future, the need to retrofit hospitals already appears more probable than to build new facilities. In Greece, holistic healthcare architecture has significant potential and room to develop. Aim: The architectural research of multi-bed patient room environment. Method: A sample of multi-bed patient rooms of a Greek hospital was studied per architectural documentation and user evaluation survey. Beyond recording the existing situation and user experience, user group differences and the influence of window proximity were studied. The survey sample was based on convenience and comprised 160 patients and 136 visitors. Statistical analysis was performed in SPSS 20, using chi-square exact tests of independence. The chosen level of significance was p < 0.05. Results: Architectural documentation showed that the building morphology had a positive impact in patient rooms, with regard to sunlight penetration and view. Further solar daylight control was deemed necessary, to facilitate overall environmental comfort conditions. High spatial density and considerable disadvantages of the middle patient bed, compared to the one bedside the window and the one further in the back of the room, were also ascertained. User groups did not evaluate their surroundings significantly different, with the exception of ease of access to the view. Window proximity influenced both patients and visitors in evaluating ease of access to the view and visual discomfort. Patients were further affected on window size evaluation and visitors on view related aspects. Conclusions: Synergy between building form and function contributes in creating holistic sustainable healing environments. User evaluation can deviate from objective documentation. Patients and visitors experienced the patient room in a similar manner. The middle bed was

VRML Programs for Room Ventilation Applications

DEFF Research Database (Denmark)

Nielsen, Anker

Cheap 3D models for visualization of room ventilation applications are now available. VRML (Virtu~l Reality Modelling Language) is found to be a good format to describe buildings, rooms and furniture. A 3D model in VRML can be placed on a World Wide Web (www) page and others can see the model...

Room temperature nanoindentation creep of hot-pressed B6O

CSIR Research Space (South Africa)

Machaka, R

2014-06-01

Full Text Available of the nanoindentation creep behavior in B6O ceramics. 1 Room temperature nanoindentation creep of hot-pressed B6O Ronald Machakaa,b,* , Trevor E. Derryb,d, Iakovos Sigalasb,c aLight Metals, Materials Science and Manufacturing, Council for Scientific..., University of the Witwatersrand, Private Bag 3, Wits, Johannesburg 2050, South Africa dSchool of Physics, University of the Witwatersrand, Private Bag 3, Wits, Johannesburg 2050, 2050 South Africa Abstract: Nanoindentation has become a widely...

Determining the Number of Participants Needed for the Usability Evaluation of E-Learning Resources: A Monte Carlo Simulation

Science.gov (United States)

Davids, Mogamat Razeen; Harvey, Justin; Halperin, Mitchell L.; Chikte, Usuf M. E.

2015-01-01

The usability of computer interfaces has a major influence on learning. Optimising the usability of e-learning resources is therefore essential. However, this may be neglected because of time and monetary constraints. User testing is a common approach to usability evaluation and involves studying typical end-users interacting with the application…

Mathematical Models for Room Air Distribution - Addendum

DEFF Research Database (Denmark)

Nielsen, Peter V.

1982-01-01

A number of different models on the air distribution in rooms are introduced. This includes the throw model, a model on penetration length of a cold wall jet and a model for maximum velocity in the dimensioning of an air distribution system in highly loaded rooms and shows that the amount of heat...... removed from the room at constant penetration length is proportional to the cube of the velocities in the occupied zone. It is also shown that a large number of diffusers increases the amount of heat which may be removed without affecting the thermal conditions. Control strategies for dual duct and single...... duct systems are given and the paper is concluded by mentioning a computer-based prediction method which gives the velocity and temperature distribution in the whole room....

Single room control for user-optimised room air conditions; Einzelraumregelung fuer nutzungsoptimiertes Raumklima

Energy Technology Data Exchange (ETDEWEB)

Lezius, A. [Staefa Control System GmbH, Leinfelden-Echterdingen (Germany)

1995-12-31

In chapter 14 of the anthology about building control the single room control for achieving user-optimised room air conditions is described. The following aspects are discussed: What is comfort? What is economic efficiency? Systems for secondary air treatment, adapted functions of the measurement and control technique, management functions, orientation of the demand at the use, investment and amortisation. (BWI) [Deutsch] Kapitel 14 des Sammelbandes ueber Building control ist dem Thema der Einzelraumregelung zur Erzielung eines nutzungsoptimierten Raumklimas gewidmet. In diesem Zusammenhang werden folgende Themenbereiche angesprochen: Was ist Komfort? Was ist Wirtschaftlichkeit? Systeme fuer sekundaere Luftbehandlung; Angepasste Funktionen der MSR-Technik; Managementfunktionen; Bedarfsorientierung an der Nutzung; Investition und Amortisation. (BWI)

Etnografia e manejo de recursos naturais pelos índios Deni, Amazonas, Brasil Ethnography and natural resources management by the Deni Indians, Amazonas, Brazil

Directory of Open Access Journals (Sweden)

Juarez Pezzuti

2009-03-01

Full Text Available São raros os estudos envolvendo o uso múltiplo de recursos naturais por populações amazônicas. Este trabalho apresenta um panorama de como os índios Deni, habitantes da região de interflúvio entre dois dos maiores afluentes de água branca da bacia amazônica, os rios Juruá e Purus, utilizam dos recursos disponíveis em seu território. Os Deni são, atualmente, índios que vivem da exploração de recursos da terra firme e de regiões alagadas. São um misto de horticultores e caçadores/coletores, que utilizam toda a sua área para a obtenção de recursos para subsistência. Como regra, deslocam periodicamente seus assentamentos, evitando o esgotamento local de recursos, e provocando a modificação local do ambiente. Esta alteração aumenta temporariamente a disponibilidade de alimento. Áreas com aldeias, pomares e roçados abandonados, por sua vez, tornam-se locais onde se concentram inúmeros recursos da flora e da fauna, posteriormente explorados. O impacto provocado por este sistema é aparentemente mínimo. Os Deni estão contextualizados na periferia de um sistema capitalista, onde a única fonte de renda para adquirir bens que são hoje considerados pelos índios como indispensáveis para sua sobrevivência são os recursos naturais. Estes são e continuarão sendo explorados de maneira a produzir um excedente a ser comercializado para a obtenção de uma série de produtos industrializados, independentemente das opiniões externas. É sobre este patamar que devemos avaliar a sustentabilidade do atual manejo da área.Studies concerning the use of multiple natural resources by Amazonian indians are scarce. This work presents a portrait of how the Deni Indians, inhabitants of an area between two of the most important white-water rivers of the Amazon basin (Juruá and Purus Rivers, exploit natural resources in their territory. The Deni exploit both the upland and floodplain forests. They are a mix of horticulturalists and

Recovery room nurses' knowledge regarding postoperative airway ...

African Journals Online (AJOL)

Adele

room nurses in private hospitals in Northern Gauteng, South Af- rica, regarding ... room nurse' is used. The same principle applies when reference is made to the terms ... Ethical considerations. Written consent ..... Principles of CPR in theatre.

DSS / Press Room

Science.gov (United States)

Defense Security Service, U.S. Department of Defense Site Map | A-Z Index | Facebook | Twitter Locations Press Room Organizational Structure Careers at DSS Doing Business with DSS Frequently Asked Classification System (NCCS) National Industrial Security System (NISS) ODAA Business Management System (OBMS

Analysis of room acoustics in Danish Hospitals

DEFF Research Database (Denmark)

Hoffmann, Ida Ørduk; Zapata Rodriguez, Valentina; Jeong, Cheol-Ho

2018-01-01

time (EDT) and T20, and the sound pressure level metrics, namely the equivalent level and peak level. In addition, the staff at the hospitals is asked about their personal perception of the acoustic and noise conditions and the correlation between their subjective disturbances......This project aims to compare room acoustic parameters and noise levels in various Danish hospitals: Odense, Gentofte, Bispebjerg, Hillerød and Aarhus Hospitals. Room acoustic conditions are measured in audiometric rooms at Odense, Gentofte, Bispebjerg and Aarhus hospitals. The noise levels...

Curriculum/Resource Development: The "C.A.R.E for St. Lucia" Resource Pack.

Science.gov (United States)

Strong, Michelle

1993-01-01

Describes a resource packet that utilizes a four-point approach to make environmental action concerning land use more accessible to teachers. The points are construct a map of the area under consideration; assess the impact of historical development, natural cycles, mining, and eco-tourism on the problem; research land use options; and encourage…

Room temperature chemical synthesis of Cu(OH)2 thin films for supercapacitor application

International Nuclear Information System (INIS)

Gurav, K.V.; Patil, U.M.; Shin, S.W.; Agawane, G.L.; Suryawanshi, M.P.; Pawar, S.M.; Patil, P.S.; Lokhande, C.D.; Kim, J.H.

2013-01-01

Highlights: •Cu(OH) 2 is presented as the new supercapacitive material. •The novel room temperature method used for the synthesis of Cu(OH) 2 . •The hydrous, nanograined Cu(OH) 2 shows higher specific capacitance of 120 F/g. -- Abstract: Room temperature soft chemical synthesis route is used to grow nanograined copper hydroxide [Cu(OH) 2 ] thin films on glass and stainless steel substrates. The structural, morphological, optical and wettability properties of Cu(OH) 2 thin films are studied by means of X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), field emission scanning electron microscopy (FESEM), UV–vis spectrophotometer and water contact angle measurement techniques. The results showed that, room temperature chemical synthesis route allows to form the nanograined and hydrophilic Cu(OH) 2 thin films with optical band gap energy of 3.0 eV. The electrochemical properties of Cu(OH) 2 thin films are studied in an aqueous 1 M NaOH electrolyte using cyclic voltammetry. The sample exhibited supercapacitive behavior with 120 F/g specific capacitance

Creators Room

DEFF Research Database (Denmark)

Iversholt, Lene; Iversholt Toft, Karina

2012-01-01

Creators Room er et koncept til daginsitutioner, der indrammer og giver bud på en forståelse mellem inkluderende pædagogik og fysiske rammer. Konceptet er udviklet i et tværfagligt procesforløb, hvor formålet har været at skabe stadig bedre indendørsmiljøer for børn ved at forene pædagogiske...

Human factors methods for nuclear control room design. Volume 2. Human factors survey of control room design practices

International Nuclear Information System (INIS)

Seminara, J.L.; Parsons, S.O.

1979-11-01

An earlier review of the control rooms of operating nuclear power plants identified many design problems having potential for degrading operator performance. As a result, the formal application of human factors principles was found to be needed. This report demonstrates the use of human factors in the design of power plant control rooms. The approaches shown in the report can be applied to operating power plants, as well as to those in the design stage. This study documents human factors techniques required to provide a sustained concern for the man-machine interface from control room concept definition to system implementation

Screening Criteria for Loss of Room Cooling Failure

Energy Technology Data Exchange (ETDEWEB)

Hwang, Mee Jeong; Yang, Joon Eon; Yoon, Churl

2007-01-15

In this report, we estimated the temperature of the pump rooms and reviewed the operability of the components under the loss of the HVAC (Heating, Ventilation, and Air Condition) system. The issues relevant to the HVAC system in the PSA (Probabilistic Safety Assessment) FT (Fault Tree) model are as follows: (1) Does the loss of the HVAC system bring about a function failure of other components? (2) Can the operator take action to reduce the temperature of the room in case of a HVAC function failure? At present, we do not know whether a component will lose its function or not under the loss of the HVAC. ASME Standard describes that a recovery action can be credited if the related recovery action is included in the procedure or there are similar recovery experiences in the plant. However, there is no description about the recovery action of the HVAC in the EOP (Emergency Operation Procedure) of the UCN3, 4 under the situation of a loss of the HVAC. Even though we consider this assumption positively, it would be limited to the rooms such as the Switchgear Room, Inverter Room, and Main Control Room etc. where a real recovery action can be performed easily. However, if we consider the HVAC failure in the PSA FT model according to the above background, the problem is that the unavailability induced from the loss of a HVAC is highly unrealistically. From a viewpoint of the PSA, it is not true that the related system always fails even though the HVAC system fails. Therefore, we reviewed the necessity of the HVAC model through the identification of the operable temperature of the components' within the pump room and the change of the temperature of the pump room under the situation of a loss of the HVAC system. In this paper, we performed a heat up calculation for the Auxiliary Feedwater Motor Operated Pump (AFW MDP) room, PAB-077-11A with CFX 10 and RATT when the HVAC system is failed. We also reviewed the operability of the components under a loss of the HVAC. Room

Screening Criteria for Loss of Room Cooling Failure

International Nuclear Information System (INIS)

Hwang, Mee Jeong; Yang, Joon Eon; Yoon, Churl

2007-01-01

In this report, we estimated the temperature of the pump rooms and reviewed the operability of the components under the loss of the HVAC (Heating, Ventilation, and Air Condition) system. The issues relevant to the HVAC system in the PSA (Probabilistic Safety Assessment) FT (Fault Tree) model are as follows: (1) Does the loss of the HVAC system bring about a function failure of other components? (2) Can the operator take action to reduce the temperature of the room in case of a HVAC function failure? At present, we do not know whether a component will lose its function or not under the loss of the HVAC. ASME Standard describes that a recovery action can be credited if the related recovery action is included in the procedure or there are similar recovery experiences in the plant. However, there is no description about the recovery action of the HVAC in the EOP (Emergency Operation Procedure) of the UCN3, 4 under the situation of a loss of the HVAC. Even though we consider this assumption positively, it would be limited to the rooms such as the Switchgear Room, Inverter Room, and Main Control Room etc. where a real recovery action can be performed easily. However, if we consider the HVAC failure in the PSA FT model according to the above background, the problem is that the unavailability induced from the loss of a HVAC is highly unrealistically. From a viewpoint of the PSA, it is not true that the related system always fails even though the HVAC system fails. Therefore, we reviewed the necessity of the HVAC model through the identification of the operable temperature of the components' within the pump room and the change of the temperature of the pump room under the situation of a loss of the HVAC system. In this paper, we performed a heat up calculation for the Auxiliary Feedwater Motor Operated Pump (AFW MDP) room, PAB-077-11A with CFX 10 and RATT when the HVAC system is failed. We also reviewed the operability of the components under a loss of the HVAC. Room

"Amor e sexo: mitos, verdades e fantasias": jovens avaliam potencial de material multimídia educativo em saúde "Love and sex: myths, truths and fantasies": youth evaluation of the multimedia resource as educational health material

Directory of Open Access Journals (Sweden)

Sonia Maria Figueira Mano

2009-01-01

Full Text Available A educação sexual na escola é prática defendida e prescrita pelo Ministério da Educação nos Parâmetros Curriculares Nacionais como eixo transversal ao currículo. O tema é complexo e a proposta expressa demandas específicas, como a formação dos professores e materiais educativos adequados. O Museu da Vida, COC/Fiocruz, desenvolveu o multimídia «Amor e sexo: mitos, verdades e fantasias» e, neste artigo, apresenta a avaliação efetuada por 36 alunos do Ensino Médio de escolas públicas do Rio de Janeiro sobre o produto. A avaliação permitiu identificar o multimídia como recurso educativo capaz de promover o tema sexualidade em situações de aprendizagem. Um recurso do multimídia, denominado Caderno de Perguntas, mostrou-se como espaço de interlocução entre os jovens, permitindo troca anônima de dúvidas e ideias, e alimentando um banco de dados que permite aos professores e pesquisadores conhecerem melhor o pensamento dos adolescentes.Sex education in schools is advised and agreed as a universal theme in the National Curriculum of the Brazilian Education Ministry. This subject is complex and the proposal expresses specific needs, such as teacher training and the support of educational materials. The Museum of Life, COC/Fiocruz, developed the multimedia resource, "Love and Sex: myths, truths and fantasies" and this study presents the results of the evaluation made by 36 high school students from public schools, in Rio de Janeiro about the multimedia resource. The evaluation identified it as an educational resource, able to promote dialogue and support the the theme sexuality in teaching situations. A multimedia resource, called Answers Notebook, gives a dialogue space between adolescents, allowing anonymity in the exchange of doubts and ideas, and feeding into a database that allow teachers and professionals to know better how adolescents think.

Learning Resources Centers and Their Effectiveness on Students’ Learning Outcomes: A Case-Study of an Omani Higher Education Institute

Directory of Open Access Journals (Sweden)

Peyman Nouraey

2017-06-01

Full Text Available The study aimed at investigating the use and effectiveness of a learning resources center, which is generally known as a library. In doing so, eight elements were investigated through an author-designed questionnaire. Each of these elements tended to delve into certain aspects of the afore-mentioned center. These elements included a students’ visits frequency, b availability of books related to modules, c center facilities, d use of discussion rooms, e use of online resources, f staff cooperation, g impact on knowledge enhancement, and, h recommendation to peers. Eighty undergraduate students participated in the study. Participants were then asked to read the statements carefully and choose one of the five responses provided, ranging from strongly agree to strongly disagree. Data were analyzed based on 5-point Likert Scale. Findings of the study revealed that participants were mostly in agreement with all eight statements provided in the questionnaire, which were interpreted as positive feedbacks from the students. Then, the frequencies of responses by the participants were reported. Finally, the results were compared and contrasted and related discussions on the effectiveness of libraries and learning resources centers on students’ learning performances and outcomes were made.

Photographic art in exam rooms may reduce white coat hypertension.

Science.gov (United States)

Harper, Michael B; Kanayama-Trivedi, Stacy; Caldito, Gloria; Montgomery, David; Mayeaux, E J; DelRosso, Lourdes M

2015-12-01

Blood pressure (BP) elevation in medical office settings in patients who are normotensive in nonmedical settings is an effect known as 'white coat hypertension'. This phenomenon is thought to be due to situational anxiety caused by the experience of visiting a doctor and the anxiety-inducing nature of the medical office. Our study was designed to determine if carefully selected photographic art could counter the anxiety that causes white coat hypertension and lead to lower BP recordings in some patients. 117 adults, non-pregnant patients from the Louisiana State University Health Sciences Center Family Medicine Resident Clinic participated in this study. After the triage nurse measured the BP, the patients were randomly placed in either an exam room with standard medical posters (control room) or in an exam room with photographic art (photo room). The BP was measured in the exam room. After the medical visit, the patients switched rooms and the BP was measured a third time. The patients were asked to fill out a questionnaire to identify room preference. On average, the BP obtained in the control rooms was higher than that obtained in the photo rooms. There was a statistically significant difference between the mean arterial pressure, systolic BP and diastolic BP between the control room and the photo room. Landscape photographic art may have the beneficial effect of reducing BP in medical office examination rooms. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

Prepare to protect: Operating and maintaining a tornado safe room.

Science.gov (United States)

Herseth, Andrew; Goldsmith-Grinspoon, Jennifer; Scott, Pataya

2017-06-01

Operating and maintaining a tornado safe room can be critical to the effective continuity of business operations because a firm's most valuable asset is its people. This paper describes aspects of operations and maintenance (O&M) for existing tornado safe rooms as well as a few planning and design aspects that affect the ultimate operation of a safe room for situations where a safe room is planned, but not yet constructed. The information is based on several Federal Emergency Management Agency safe room publications that provide guidance on emergency management and operations, as well as the design and construction of tornado safe rooms.

Resource Utilisation and Curriculum Implementation in Community Colleges in Kenya

Directory of Open Access Journals (Sweden)

Peter Changilwa Kigwilu

2017-12-01

Full Text Available The study investigated how Catholic-sponsored community colleges in Nairobi utilise the existing physical facilities and teaching and learning resources for effective implementation of Artisan and Craft curricula. The study adopted a mixed methods research design. Proportional stratified random sampling was used to sample 172 students and 18 teachers while four directors of community colleges were purposively selected. Questionnaires were administered to students and teachers, while directors were interviewed. Teaching and learning resources, such as workshops, equipment, lecture rooms, laboratories, raw materials for practical training and reference books, were found to be adequate, although underutilised. However, sports grounds, libraries and course texts were inadequate. Resource inadequacies were often mitigated by signing equipment co-sharing agreements with peer institutions and local firms. Teachers rated highly the influence of physical facilities on curriculum implementation. Both students and teachers rated highly the influence of teaching and learning resources on curriculum implementation. The study concludes that, while some physical facilities and teaching and learning resources are adequate, their underutilisation and the inadequacy of other core facilities and resources, such as libraries and course textbooks, hinder effective teaching and learning in these community colleges.

RLA room 20 cleanout and stabilization

International Nuclear Information System (INIS)

Ham, J.E.

1997-01-01

This engineering report documents the decontamination and stabilization of the Rupture Loop Annex located in room 20 of the 309 building's Plutonium Recycle Test Reactor. Low level, mixed, and recyclable waste was removed from the room. Smearable contamination was removed and/or fixed in place with paint. The RLA was cleaned out and stabilized to meet the Environmental Restoration Contractor's turnover criteria

Measles transmission in health care waiting rooms: implications for public health response

Directory of Open Access Journals (Sweden)

Stephen Conaty

2012-12-01

Full Text Available Background: Seventeen cases of locally acquired measles occurred in South Western Sydney and Sydney local health districts between July and October 2011. Three of the cases were known to have at least one dose of measles-mumps-rubella (MMR vaccine. Seven cases were infected within a health care setting waiting room by five index cases. Current national protocols require follow-up of all susceptible contacts in the same waiting room for any length of time for up to two hours after the index case has left.Methods: Cases were interviewed using a standardized questionnaire. Information included: demographics, illness and activities during the exposure and infectious periods. Health care settings provided arrival and discharge times, maps of floor layouts and location of patients during stay.Results: All health care setting transmission occurred in cases who were present at the same time as their index cases, with cross-over time ranging from 20 to 254 minutes. No index case was isolated. Index cases were between day four and six of illness when transmission occurred. None of the five index cases and one of seven secondary cases had received at least one dose of MMR vaccine. Of the seven secondary cases, two were one year of age, one was 17 years old and four were between 30 and 39 years old.Conclusion: As Australia moves towards measles elimination, follow-up of cases is important; however, with limited public health resources a targeted response is vital. In this small but well-documented series of secondary cases acquired in a health care setting, all were infected following direct, proximate contact of at least 20 minutes. Changes to the national guidelines may be warranted, ensuring that limited resources are focused on following up contacts at greatest risk of disease.

Perception of tomorrow's nuclear power plant control rooms

International Nuclear Information System (INIS)

Meyer, O.R.

1986-01-01

Major development programs are upgrading today's light water reactor nuclear power plant (NPP) control rooms. These programs involve displays, control panel architecture, procedures, staffing, and training, and are supported by analytical efforts to refine the definitions of the dynamics and the functional requirements of NPP operation. These programs demonstrate that the NPP control room is the visible command/control/communications center of the complex man/machine system that operates the plant. These development programs are primarily plant specific, although the owners' groups and the Institute of Nuclear Power Operations (INPO) do provide some standardization. The Idaho National Engineering Laboratory recently completed a project to categorize control room changes and estimate the degree of change. That project, plus related studies, provides the basis for this image of the next generation of NPP control rooms. The next generation of NPP control rooms is envisioned as being dominated by three current trends: (1) application of state-of-the-art computer hardware and software; (2) use of NPP dynamic analyses to provide the basis for the control room man/machine system design; and (3) application of empirical principles of human performance

Active low frequency sound field control in a listening room using CABS (Controlled Acoustic Bass System) will also reduce the sound transmitted to neighbour rooms

DEFF Research Database (Denmark)

Nielsen, Sofus Birkedal; Celestinos, Adrian

2012-01-01

Sound in rooms and transmission of sound between rooms gives the biggest problems at low frequencies. Rooms with rectangular boundaries have strong resonance frequencies and will give big spatial variations in sound pressure level (SPL) in the source room, and an increase in SPL of 20 dB at a wall...... Bass System) is a time based room correction system for reproduced sound using loudspeakers. The system can remove room modes at low frequencies, by active cancelling the reflection from at the rear wall to a normal stereo setup. Measurements in a source room using CABS and in two neighbour rooms have...... shown a reduction in sound transmission of up to 10 dB at resonance frequencies and a reduction at broadband noise of 3 – 5 dB at frequencies up to 100 Hz. The ideas and understanding of the CABS system will also be given....

Competição por recursos do solo entre ervas daninhas e culturas Competition between weeds and crops by soil resources

Directory of Open Access Journals (Sweden)

Mauro Antônio Rizzardi

2001-08-01

Full Text Available A competição entre plantas é um processo importante tanto em comunidades naturais quanto em ambientes agrícolas. O impacto vegetativo das ervas daninhas em agroecossistemas é considerado competição se houver redução no montante de recursos disponíveis para a cultura e, neste contexto, o desenvolvimento das raízes influencia na competitividade e na sobrevivência das plantas. Uma planta que apresenta sistema radical bem desenvolvido em extensão e em comprimento tem sido associada com aumento na habilidade competitiva devido ao maior potencial de absorção de água e nutrientes. A competição entre os sistemas radicais das ervas daninhas e das culturas interfere tanto na disponibilidade de água e nutrientes quanto nas interações por luz, na parte aérea. Entretanto, somente ocorrerá competição quando a zona de depleção das raízes da cultura e das ervas daninhas se sobreporem. A intensidade de competição entre raízes das ervas e da cultura pelos recursos abaixo da superfície do solo dependerá do tipo e da disponibilidade dos recursos e da espécie vegetal e de sua capacidade em desenvolver sistema radical extenso, com diâmetro reduzido e com ampla área superficial.Competition between plants is an important process as much in natural communities as in agricultural environments. The impact of weeds in agroecossystems is refered as competition if there is a reduction in the amount of resources available for the crop and, in this context, root development influences plant competitivity and survival. A plant which presents a well developed root system in extension and in length has been associated with increased competition hability due to a greater absorption capacity of water and nutrients. Competition between root systems of weeds and crops interferes in water and nutrients availability, as well as in interactions for light in the aerial system. However, competition will only occur when depletion zone of crop and weed

Room-temperature antiferromagnetic memory resistor.

Science.gov (United States)

Marti, X; Fina, I; Frontera, C; Liu, Jian; Wadley, P; He, Q; Paull, R J; Clarkson, J D; Kudrnovský, J; Turek, I; Kuneš, J; Yi, D; Chu, J-H; Nelson, C T; You, L; Arenholz, E; Salahuddin, S; Fontcuberta, J; Jungwirth, T; Ramesh, R

2014-04-01

The bistability of ordered spin states in ferromagnets provides the basis for magnetic memory functionality. The latest generation of magnetic random access memories rely on an efficient approach in which magnetic fields are replaced by electrical means for writing and reading the information in ferromagnets. This concept may eventually reduce the sensitivity of ferromagnets to magnetic field perturbations to being a weakness for data retention and the ferromagnetic stray fields to an obstacle for high-density memory integration. Here we report a room-temperature bistable antiferromagnetic (AFM) memory that produces negligible stray fields and is insensitive to strong magnetic fields. We use a resistor made of a FeRh AFM, which orders ferromagnetically roughly 100 K above room temperature, and therefore allows us to set different collective directions for the Fe moments by applied magnetic field. On cooling to room temperature, AFM order sets in with the direction of the AFM moments predetermined by the field and moment direction in the high-temperature ferromagnetic state. For electrical reading, we use an AFM analogue of the anisotropic magnetoresistance. Our microscopic theory modelling confirms that this archetypical spintronic effect, discovered more than 150 years ago in ferromagnets, is also present in AFMs. Our work demonstrates the feasibility of fabricating room-temperature spintronic memories with AFMs, which in turn expands the base of available magnetic materials for devices with properties that cannot be achieved with ferromagnets.

The Operating Room of the Future Versus the Future of the Operating Room.

Science.gov (United States)