A study of radiation therapy for the cervical stump cancer

International Nuclear Information System (INIS)

Ohkawa, Reiko; Arai, Tatsuo; Morita, Shinroku; Takamizawa, Hirokichi.

1979-01-01

During a period of 17 years, between 1961 and 1977, 59 cases of the cervical stump cancer were treated at NIRS Hospital. We could not epidemically find the difference between the cervical stump cancer and the cervical cancer. 5-year survival rate of cervical stump cancer was 90% in stage I, 86% in stage II, and 63% in stage III, respectively. These results show higher 5-year survival rates, compared with those of cervical cancer. The frequencies of radiation complication in rectum and bladder were lower in the case of cervical stump cancer than in cervical cancer. It was suggested that the optimal radiation dose for cervical stump cancer was 80 - 90 TDF at point A. (author)

Thirteen Year Loblolly Pine Growth Following Machine Application of Cut-Stump Treament Herbicides For Hardwood Stump-Sprout Control

Science.gov (United States)

Clyde G. Vidrine; John C. Adams

2002-01-01

Thirteen year growth results of 1-0 out-planted loblolly pine seedlings on nonintensively prepared up-land mixed pine-hardwood sites receiving machine applied cut-stump treatment (CST) herbicides onto hardwood stumps at the time of harvesting is presented. Plantation pine growth shows significantly higher growth for pine in the CST treated plots compared to non-CST...

Relation of Stump Length with Various Gait Parameters in Trans-tibial Amputee

Directory of Open Access Journals (Sweden)

Koyel Majumdar

2008-07-01

Full Text Available The purpose of this paper is evaluating the impact of stump length of unilateral below knee amputees (BKA on different gait parameters. Nine unilateral BKA were chosen and divided into three groups comprising patients with short, medium, and long stump length. Each of them underwent gait analysis test by Computer Dynography (CDG system to measure the gait parameters. It was found that the ground reaction force is higher in the patients with medium stump length whereas the velocity, step length both for the prosthetic and sound limb and cadence were high in longer stump length. Statistical analysis shows a significant difference (p<0.05 between the gait parameters of BKA with medium and longer stump length. The patients with longer stump length were more efficient than medium and short stump patients as they consumed comparatively lesser energy while walking with self-selected velocity and conventional (Solid ankle cushioned heel SACH foot.

Occurrence patterns of lichens on stumps in young managed forests.

Science.gov (United States)

Svensson, Måns; Dahlberg, Anders; Ranius, Thomas; Thor, Göran

2013-01-01

The increasing demand for forest-derived bio-fuel may decrease the amount of dead wood and hence also the amount of available substrate for saproxylic ( = dead-wood dependent) organisms. Cut stumps constitute a large portion of dead wood in managed boreal forests. The lichen flora of such stumps has received little interest. Therefore, we investigated which lichens that occur on stumps in young (4-19 years), managed forests and analyzed how species richness and occurrence of individual species were related to stump and stand characteristics. We performed lichen inventories of 576 Norway spruce stumps in 48 forest stands in two study areas in Central Sweden, recording in total 77 lichen species. Of these, 14 were obligately lignicolous, while the remaining were generalists that also grow on bark, soil or rocks. We tested the effect of characteristics reflecting successional stage, microclimate, substrate patch size, and the species pool in the surrounding area on (1) total lichen species richness, (2) species richness of obligately lignicolous lichens and (3) the occurrence of four obligately lignicolous lichen species. The most important variables were stump age, with more species on old stumps, and study area, with similar total species richness but differences in occupancy for individual species. Responses for total lichen species richness and species richness of obligately lignicolous lichens were overall similar, indicating similar ecological requirements of these two groups. Our results indicate that species richness measurements serve as poor proxies for the responses of individual, obligately lignicolous lichen species.

Occurrence patterns of lichens on stumps in young managed forests.

Directory of Open Access Journals (Sweden)

Måns Svensson

Full Text Available The increasing demand for forest-derived bio-fuel may decrease the amount of dead wood and hence also the amount of available substrate for saproxylic ( = dead-wood dependent organisms. Cut stumps constitute a large portion of dead wood in managed boreal forests. The lichen flora of such stumps has received little interest. Therefore, we investigated which lichens that occur on stumps in young (4-19 years, managed forests and analyzed how species richness and occurrence of individual species were related to stump and stand characteristics. We performed lichen inventories of 576 Norway spruce stumps in 48 forest stands in two study areas in Central Sweden, recording in total 77 lichen species. Of these, 14 were obligately lignicolous, while the remaining were generalists that also grow on bark, soil or rocks. We tested the effect of characteristics reflecting successional stage, microclimate, substrate patch size, and the species pool in the surrounding area on (1 total lichen species richness, (2 species richness of obligately lignicolous lichens and (3 the occurrence of four obligately lignicolous lichen species. The most important variables were stump age, with more species on old stumps, and study area, with similar total species richness but differences in occupancy for individual species. Responses for total lichen species richness and species richness of obligately lignicolous lichens were overall similar, indicating similar ecological requirements of these two groups. Our results indicate that species richness measurements serve as poor proxies for the responses of individual, obligately lignicolous lichen species.

Stump treatment against Heterobasidion annosum - Techniques and biological effect in practical forestry

Energy Technology Data Exchange (ETDEWEB)

Thor, M. [SkogForsk, Uppsala (Sweden)

1997-12-31

This thesis summarises and discusses results from two studies on mechanized stump treatment to control the root rot fungus Heterobasidion annosum (Fr.) Bref. In Sweden, stump treatment is at present carried out with two chemical compounds, urea and disodium octaborate tetrahydrate (DOT), and a biological control agent, Phlebiopsis gigantea (Fr.) Juel. The first study investigated the H. annosum colonization of Norway spruce (Picea abies (L.) Karst) stumps following mechanized thinning and stump treatment with the three control agents mentioned. The stumps were treated in the summer and were compared with untreated stumps, cut in the summer and winter, respectively. Experimental plots were established in 12 first thinning stands of Norway spruce. Six to seven weeks after thinning and treatment, sample discs were collected (N=1246) and examined for presence of H. annosum. Stump treatment with any of the control agents reduced the colonized stump area 6-7 weeks after thinning by 88-98% as compared with untreated stumps cut in the summer. The effects of the different treatments differed neither from each other nor from the effect of winter thinning. The variation between the stands was considerable, but mechanized stump treatment provided as good protection as manual treatment against H. annosum infections. Study II examined the survival of P. gigantea oidiospores in aqueous suspension when exposed to high temperature or pressure, which are potential problems in mechanized application. In the laboratory, temperatures of 20, 30 or 35 deg C did not affect the survival. The spores could withstand 40 deg C for a short period, but died at 60 deg C. Pressure of up to 2 200 kPa for 24 h did not affect P. gigantea spore germination. In the field, temperatures of the working suspension (10{sup 7} spores I{sup -1}) was assessed during practical operations. Spore viability was maintained through the applicator system. As long as the prescriptions are followed up to the time of

Tinea corporis on the stump leg with Trichophyton rubrum infection

Directory of Open Access Journals (Sweden)

Xin Ran

2015-09-01

Full Text Available We report a case of tinea corporis on amputated leg stump caused by Trichophyton rubrum. The patient, a 54-year-old male, experienced a serious traffic accident, resulted his right leg amputated 3 years ago. Since then prosthesis was fitted and protective equipment of silicone stocking was worn for the stump. He consulted with circular, patchy and scaly erythemas with itching on his right below knee amputation stump for 2 months. The diagnoses of tinea corporis on the stump was made based on a positive KOH direct microscopic examination, morphologic characteristics and sequencing of the internal transcribed spacers (ITS 1 and 4, confirmed that the isolate from the scales was T. rubrum. The patient was cured with oral terbinafine and topical naftifine-ketaconazole cream following 2% ketaconazole shampoo wash for 3 weeks. Long times using prosthesis together with protective equipment of silicone stocking, leading to the local environment of airtight and humid within the prosthesis favors T. rubrum infection of the stump could be considered as the precipitating factors.

Testing Open-Air Storage of Stumps to Provide Clean Biomass for Energy Production

Directory of Open Access Journals (Sweden)

Luigi Pari

2017-10-01

Full Text Available When orchards reach the end of the productive cycle, the stumps removal becomes a mandatory operation to allow new soil preparation and to establish new cultivations. The exploitation of the removed stump biomass seems a valuable option, especially in the growing energy market of the biofuels; however, the scarce quality of the material obtained after the extraction compromises its marketability, making this product a costly waste to be disposed. In this regard, the identification of affordable strategies for the extraction and the cleaning of the material will be crucial in order to provide to plantation owners the chance to sell the biomass and offset the extraction costs. Mechanical extraction and cleaning technologies have been already tested on forest stumps, but these systems work on the singular piece and would be inefficient in the conditions of an intensive orchard, where stumps are small and numerous. The objective of this study was to test the possibility to exploit a natural stumps cleaning system through open-air storage. The tested stumps were obtained from two different vineyards, extracted with an innovative stump puller specifically designed for continuous stump removal in intensively-planted orchards. The effects of weathering were evaluated to determine the fuel quality immediately after the extraction and after a storage period of six months with respect to moisture content, ash content, and heating value. Results indicated interesting storage performance, showing also different dynamics depending on the stumps utilized.

A Rare Case: Appendectomy After Connected Stump Appendicitis Perforation of the Cecum

Directory of Open Access Journals (Sweden)

Berke Manoglu

2016-01-01

Full Text Available Stump appendicitis is a rare complication after appendectomy . Stump appendicitis made of incomplete appendectomy after a rest appendix tissue develops as a result of the inflammation. Admitted to the emergency department with acute abdomen and a history of appendectomy in patients with a history of current pain in the right lower quadrant , especially that of the patient must be evaluated in terms of stump appendicitis. The fact that the earlier story appendectomy patients , causing a delay in diagnosis and increasing the morbidity Cecal perforation was offered an advanced case of delayed depending on the stump appendicitis in this article.

Tree diameter at breast height in relation to stump diameter by species group

Science.gov (United States)

Arthur G. Horn; Richard C. Keller

1957-01-01

A stump tally is one method of determining the volume of timber previously removed from an area in a logging operation. To estimate volume of standing timber from stumps, foresters must first know the relationship between stump diameters and tree diameters at breast height (d.b.h.).

Stereotactic body radiation therapy for patients with recurrent pancreatic adenocarcinoma at the abdominal lymph nodes or postoperative stump including pancreatic stump and other stump

Directory of Open Access Journals (Sweden)

Zeng XL

2016-06-01

Full Text Available Xian-Liang Zeng,* Huan-Huan Wang,* Mao-Bin Meng, Zhi-Qiang Wu, Yong-Chun Song, Hong-Qing Zhuang, Dong Qian, Feng-Tong Li, Lu-Jun Zhao, Zhi-Yong Yuan, Ping Wang Department of Radiation Oncology, Tianjin’s Clinical Research Center for Cancer and Key Laboratory of Cancer Prevention and Therapy, Tianjin Medical University Cancer Institute and Hospital, National Clinical Research Center for Cancer, Tianjin, People’s Republic of China *These authors contributed equally to this work Background and aim: The aim of this study is to evaluate the efficacy and safety of stereotactic body radiation therapy (SBRT using CyberKnife in the treatment of patients with recurrent pancreatic adenocarcinoma at the abdominal lymph node or stump after surgery. Patients and methods: Between October 1, 2006 and May 1, 2015, patients with recurrent pancreatic adenocarcinoma at the abdominal lymph node or stump after surgery were enrolled and treated with SBRT at our hospital. The primary end point was local control rate after SBRT. Secondary end points were overall survival, time to symptom alleviation, and toxicity, assessed using the Common Terminology Criteria for Adverse Events version 4.0. Results: Twenty-four patients with 24 lesions (17 abdominal lymph nodes and seven stumps were treated with SBRT, of which five patients presented with abdominal lymph nodes and synchronous metastases in the liver and lung. The 6-, 12-, and 24-month actuarial local control rates were 95.2%, 83.8%, and 62.1%, respectively. For the entire cohort, the median overall survival from diagnosis and SBRT was 28.9 and 12.2 months, respectively. Symptom alleviation was observed in eleven of 14 patients (78.6% within a median of 8 days (range, 1–14 days after SBRT. Nine patients (37.5% experienced Common Terminology Criteria for Adverse Events version 4.0 grade 1–2 acute toxicities; one patient experienced grade 3 acute toxicity due to thrombocytopenia. Conclusion: SBRT is a safe and

7 CFR 160.85 - Sale of mixed turpentine not lawful.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Sale of mixed turpentine not lawful. 160.85 Section 160.85 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE (CONTINUED) NAVAL STORES...

First rotation Eucalyptus macarthurii cut stump control in KwaZulu ...

African Journals Online (AJOL)

Many cold tolerant eucalypts, E. macarthurii in particular, coppice vigorously following harvesting, and in contrast to E. grandis are proving difficult to kill by existing cut stump control methods. Based on past research, selected cut stump treatments were tested on single stem E. macarthurii trees, that had not been coppiced, ...

[Cancer of the gastric stump].

Science.gov (United States)

Rojas Bravo, F; Montero, L

1992-01-01

627 cases of gastric cancer treated surgically during the last 5 years, at the Hospital Nacional "Edgardo Rebagliati Martins" from Instituto Peruano de Seguridad Social (Lima-Perú) were revised. 4 of the patients had been operated before of hemigastrectomy or antrectomy with pyloroplasty for peptic ulcer. The time between the first operation and diagnosis of cancer of the gastric stump was more than 20 years. 3 of these cases were able to be resected. The international incidence of cancer in the gastric stump is 1.1% to 9.2% according to different authors. The risk is higher after 15 years. In the pathogenesis are advocated the lower gastric acidity, biliary reflux, the presence of bacteria, the formation of nitrosamines, intestinal metaplasia, etc. Is necessary to perform periodic endoscopic survey in patients who were treated surgically of peptic ulcer with antrectomy or hemigastrectomy with more than 15 years of evolution.

A novel rat model of brachial plexus injury with nerve root stumps.

Science.gov (United States)

Fang, Jintao; Yang, Jiantao; Yang, Yi; Li, Liang; Qin, Bengang; He, Wenting; Yan, Liwei; Chen, Gang; Tu, Zhehui; Liu, Xiaolin; Gu, Liqiang

2018-02-01

The C5-C6 nerve roots are usually spared from avulsion after brachial plexus injury (BPI) and thus can be used as donors for nerve grafting. To date, there are no appropriate animal models to evaluate spared nerve root stumps. Hence, the aim of this study was to establish and evaluate a rat model with spared nerve root stumps in BPI. In rupture group, the proximal parts of C5-T1 nerve roots were held with the surrounding muscles and the distal parts were pulled by a sudden force after the brachial plexus was fully exposed, and the results were compared with those of sham group. To validate the model, the lengths of C5-T1 spared nerve root stumps were measured and the histologies of the shortest one and the corresponding spinal cord were evaluated. C5 nerve root stump was found to be the shortest. Histology findings demonstrated that the nerve fibers became more irregular and the continuity decreased; numbers and diameters of myelinated axons and thickness of myelin sheaths significantly decreased over time. The survival of motoneurons was reduced, and the death of motoneurons may be related to the apoptotic process. Our model could successfully create BPI model with nerve root stumps by traction, which could simulate injury mechanisms. While other models involve root avulsion or rupturing by distal nerve transection. This model would be suitable for evaluating nerve root stumps and testing new therapeutic strategies for neuroprotection through nerve root stumps in the future. Copyright © 2017. Published by Elsevier B.V.

Des Ogle's old stump

International Nuclear Information System (INIS)

Jones, M.; Sutton, D.; Wallace, R.

1998-01-01

On 17 October 1997 Sylvia Bryan of RD4 Kaitaia wrote to 'Dear Somebody-Everybody' at the Anthropology Department, University of Auckland, urging further examination of an adzed stump found by Des Ogle during planting out of the Te Aupouri forest. The authors have since sought out relevant information and present it here for the interests of our readers. (author). 7 refs., 1 fig

Treatment of Picea abies and Pinus sylvestris Stumps with Urea and Phlebiopsis gigantea for Control of Heterobasidion

Directory of Open Access Journals (Sweden)

Kalle Kärhä

2018-03-01

Full Text Available Heterobasidion spp. root rot causes severe damage to forests throughout the northern temperate zone. In order to prevent Heterobasidion infection in summertime cuttings, stumps can be treated with urea or Phlebiopsis gigantea. In this study, the consumption of stump treatment materials and the quality of stump treatment work were investigated. A total of 46 harvesters were examined in May–November 2016 in Finland. The average stem size of softwood removal and softwood removal per hectare explained the consumption of stump treatment material. The quality of stump treatment work was good in the study. The best coverage was achieved with the stumps of 20–39 cm diameter at stump height (d0. It can be recommended that the harvester operator self-monitors and actively controls his/her treatment result in cutting work and sets the stump treatment equipment in a harvester if needed. The results also suggested that when cutting mostly small- and medium-diameter (d0 ≤ 39 cm conifers, the stump treatment guide bars with relatively few (<18 open holes are used, and at the harvesting sites of large-diameter trees, the guide bars with a relatively great (>27 number of open holes are applied.

Biofuels from stumps and small roundwood - Costs and CO{sub 2} benefits

Energy Technology Data Exchange (ETDEWEB)

Eriksson, Lisa Naeslund; Gustavsson, Leif [Ecotechnology, Department of Engineering, Physics and Mathematics, Mid Sweden University, SE-831 25 Oestersund (Sweden)

2008-10-15

In this study, we analysed and compared costs, primary energy use and CO{sub 2} benefits of recovering stumps and small roundwood from thinnings, together with logging residues. Small roundwood, chipped at a terminal or end-user, has a cost comparable to the chip system and a primary energy use comparable to the bundle system used for recovery of logging residues. The small roundwood system with roadside chipping is more expensive. As productivity in the cutting process improves, the small roundwood alternatives become more cost-effective. The stump system has costs in the same range as or lower than the chip and bundle systems. Forestry operations for stump and small roundwood recovery require considerable primary energy, but net recovery per hectare is much greater than for the chip and bundle systems, which means that more fossil fuel can be displaced per hectare of clearcut than with a chip or a bundle system. Stumps and small roundwood from thinnings can become as cost-effective as logging residues in the near future. Furthermore, when stumps and small roundwood from thinnings are also used to replace fossil fuels, the potential CO{sub 2} reduction will be about four times as great as when only logging residues are used with a traditional chip system. (author)

Morphohistological features of pancreatic stump are the main determinant of pancreatic fistula after pancreatoduodenectomy.

Science.gov (United States)

Ridolfi, Cristina; Angiolini, Maria Rachele; Gavazzi, Francesca; Spaggiari, Paola; Tinti, Maria Carla; Uccelli, Fara; Madonini, Marco; Montorsi, Marco; Zerbi, Alessandro

2014-01-01

Pancreatic surgery is challenging and associated with high morbidity, mainly represented by postoperative pancreatic fistula (POPF) and its further consequences. Identification of risk factors for POPF is essential for proper postoperative management. Evaluation of the role of morphological and histological features of pancreatic stump, other than main pancreatic duct diameter and glandular texture, in POPF occurrence after pancreaticoduodenectomy. Between March 2011 and April 2013, we performed 145 consecutive pancreaticoduodenectomies. We intraoperatively recorded morphological features of pancreatic stump and collected data about postoperative morbidity. Our dedicated pathologist designed a score to quantify fibrosis and inflammation of pancreatic tissue. Overall morbidity was 59,3%. Mortality was 4,1%. POPF rate was 28,3%, while clinically significant POPF were 15,8%. Male sex (P = 0.009), BMI ≥ 25 (P = 0.002), prolonged surgery (P = 0.001), soft pancreatic texture (P < 0.001), small pancreatic duct (P < 0.001), pancreatic duct decentralization on stump anteroposterior axis, especially if close to the posterior margin (P = 0.031), large stump area (P = 0.001), and extended stump mobilization (P = 0.001) were related to higher POPF rate. Our fibrosis-and-inflammation score is strongly associated with POPF (P = 0.001). Pancreatic stump features evaluation, including histology, can help the surgeon in fitting postoperative management to patient individual risk after pancreaticoduodenectomy.

Crown-Stump Diameter Model for Parkia biglobosa Benth. Species in Makurdi, Benue State, Nigeria

Directory of Open Access Journals (Sweden)

O. Chukwu

2017-07-01

Full Text Available The crown of tree is the centre of physiological activity which gives an indication of the potential photosynthetic capacity on a tree. Though, its measurement remains a challenge in forest inventory task. The ability to predict crown diameter from stump diameter provides an effective technique of obtaining its estimate. This helps in detecting the excessive tree felling than actual requirements and wildlife suitability.The main objective of this study was to develop and test crown diameter prediction models for silvicultural management of naturally grown Parkia biglobosa within the University of Agriculture, Makurdi. Nine 100 m x 100 m temporary sample plots were established using simple random sampling method. Crown diameter and stump diameter were measured in all living P. biglobosa trees with stump diameter ≥10.0 cm. Least square method was used to convert the counted stumps into harvested crown dimension. Three linear and three non-linear models using stump diameter as the exploratory variable were developed and evaluated using the adjusted coefficient of determination (Adj.R2, standard error of estimate (SEE, prediction error sum of squares (PRESS and Akaike information criterion (AIC. The crown-stump diameter relationship was best described by the double logarithmic function with .The result showed that Crown diameter estimation was feasible even when the only information available is stump diameter.The resulting equation was tested for validation with independent data obtained from additional plots and was found to be desirable for estimating the crown diameter for Parkia biglobosa in Makurdi, Benue State, Nigeria.

Percutaneous Management of Postoperative Duodenal Stump Leakage with Foley Catheter

International Nuclear Information System (INIS)

Oh, Jung Suk; Lee, Hae Giu; Chun, Ho Jong; Choi, Byung Gil; Lee, Sang Hoon; Hahn, Seong Tai; Ohm, Joon Young

2013-01-01

Purpose: This study was designed to evaluate retrospectively the safety and efficacy of the percutaneous management of duodenal stump leakage with a Foley catheter after subtotal gastrectomy. Methods: Ten consecutive patients (M:F = 9:1, median age: 64 years) were included in this retrospective study. The duodenal stump leakages were diagnosed in all the patients within a median of 10 days (range, 6–20). At first, the patients underwent percutaneous drainage on the day of or the day after confirmation of the presence of duodenal stump leakage, and then the Foley catheters were replaced at a median of 9 days (range, 6–38) after the percutaneous drainage. Results: Foley catheters were placed successfully in the duodenal lumen of all the patients under a fluoroscopic guide. No complication was observed during and after the procedures in all the patients. All of the patients started a regular diet 1 day after the Foley catheter placement. The patients were discharged at a median of 7 days (range, 5–14) after the Foley catheter placement. The catheters were removed in an outpatient clinic 10–58 days (median, 28) after the Foley catheter placement. Conclusions: Fluoroscopy-guided percutaneous Foley catheter placement may be a safe and effective treatment option for postoperative duodenal stump leakage and may allow for shorter hospital stays, earlier oral intake, and more effective control of leakage sites

Pulsed radiofrequency of brachial plexus under ultrasound guidance for refractory stump pain: a case report

Directory of Open Access Journals (Sweden)

Zheng B

2017-11-01

Full Text Available Bixin Zheng, Li Song, Hui Liu Department of Pain Management, West China Hospital of Sichuan University, Chengdu, China Abstract: The post-amputation (pain syndrome, including stump pain, phantom limb sensation, and phantom limb pain is common but difficult to treat. Refractory stump pain in the syndrome is an extremely challenging and troublesome clinical condition. Patients respond poorly to drugs, nerve blocks, and other effective treatments like spinal cord stimulation and surgery. Pulsed radiofrequency (PRF technique has been shown to be effective in reducing neuropathic pain. This report describes a patient with persistent and refractory upper limb stump pain being successfully relieved with PRF of brachial plexus under ultrasound guidance after a 6-month follow-up period, suggesting that PRF may be considered as an alternative treatment for refractory stump-neuroma pain. Keywords: ultrasound guidance, pulsed radiofrequency, brachial plexus, refractory stump pain 

Morphohistological Features of Pancreatic Stump Are the Main Determinant of Pancreatic Fistula after Pancreatoduodenectomy

Directory of Open Access Journals (Sweden)

Cristina Ridolfi

2014-01-01

Full Text Available Introduction. Pancreatic surgery is challenging and associated with high morbidity, mainly represented by postoperative pancreatic fistula (POPF and its further consequences. Identification of risk factors for POPF is essential for proper postoperative management. Aim of the Study. Evaluation of the role of morphological and histological features of pancreatic stump, other than main pancreatic duct diameter and glandular texture, in POPF occurrence after pancreaticoduodenectomy. Patients and Methods. Between March 2011 and April 2013, we performed 145 consecutive pancreaticoduodenectomies. We intraoperatively recorded morphological features of pancreatic stump and collected data about postoperative morbidity. Our dedicated pathologist designed a score to quantify fibrosis and inflammation of pancreatic tissue. Results. Overall morbidity was 59,3%. Mortality was 4,1%. POPF rate was 28,3%, while clinically significant POPF were 15,8%. Male sex (P=0.009, BMI≥25 (P=0.002, prolonged surgery (P=0.001, soft pancreatic texture (P<0.001, small pancreatic duct (P<0.001, pancreatic duct decentralization on stump anteroposterior axis, especially if close to the posterior margin (P=0.031, large stump area (P=0.001, and extended stump mobilization (P=0.001 were related to higher POPF rate. Our fibrosis-and-inflammation score is strongly associated with POPF (P=0.001. Discussion and Conclusions. Pancreatic stump features evaluation, including histology, can help the surgeon in fitting postoperative management to patient individual risk after pancreaticoduodenectomy.

A Comparative Study on Turpentine Oils of Oleoresins of Pinus sylvestris L. from Three Districts of Denizli

Directory of Open Access Journals (Sweden)

İbrahim Tümen

2010-10-01

Full Text Available Oleoresin samples collected from Pinus sylvestris L. trees from Acıpayam, Çal and Çamlıbel, three different locations in Denizli-Turkey. The constituents of the turpentine oil, obtained by hydrodistillation of oleoresin of Pinus sylvestris L., were identified by GC-MS. Fifty four constituents were detected from the turpentine oil, which constituted about between 96.2% and 98.2% of the total amount. Major constituents of the oil were a-pinene, b-pinene, camphene, longifolene, D3-carene, limonene and b-caryophyllene

Performance and emission characteristics of turpentine-diesel dual fuel engine and knock suppression using water diluents

Energy Technology Data Exchange (ETDEWEB)

Karthikeyan, R. [Adhiparasakthi Engineering College, Tamil Nadu (India); Mahalakshmi, N.V. [College of Engineering Guindy, Tamil Nadu (India). Dept. of Mechanical Engineering

2007-08-15

In the present work, a normal diesel engine was modified to work in a dual fuel (DF) mode with turpentine and diesel as primary and pilot fuels, respectively. The resulting homogeneous mixture was compressed to a temperature below the self-ignition point. The pilot fuel was injected through the standard injection system and initiated the combustion in the primary-fuel air mixture. The primary fuel (turpentine) has supplied most of the heat energy. Usually, in all DF engines, low-cetane fuels are preferred as a primary fuel. Therefore, at higher loads these fuels start knocking and deteriorating in performances. Usually, DF operators suppress the knock by adding more pilot-fuel quantity. But in the present work, a minimum pilot-fuel quantity was maintained constant throughout the test and a required quantity of diluent (water) was added into the combustion at the time of knocking. The advantages of this method of knock suppression are restoration of performance at full load, maintenance of the same pilot quantity through the load range and reduction in the fuel consumption at full load. From the results, it was found that all performance and emission parameters of turpentine, except volumetric efficiency, are better than those of diesel fuel. The emissions like CO, UBHC are higher than those of the diesel baseline (DBL) and around 40-45% reduction of smoke was observed at 100% of full load. The major pollutant of diesel engine, NO{sub x}, was found to be equal to that of DBL. From the above experiment, it was proved that approximately 80% replacement of diesel with turpentine is quite possible. (author)

Variation in Measurements of Transtibial Stump Model Volume A Comparison of Five Methods

NARCIS (Netherlands)

Bolt, A.; de Boer-Wilzing, V. G.; Geertzen, J. H. B.; Emmelot, C. H.; Baars, E. C. T.; Dijkstra, P. U.

Objective: To determine the right moment for fitting the first prosthesis, it is necessary to know when the volume of the stump has stabilized. The aim of this study is to analyze variation in measurements of transtibial stump model volumes using the water immersion method, the Design TT system, the

Involvement of the cervical sympathetic nervous system in the changes of calcium homeostasis during turpentine oil-induced stress in rats.

Science.gov (United States)

Stern, J E; Ladizesky, M G; Keller Sarmiento, M I; Cardinali, D P

1993-03-01

Hypocalcemia is a common finding during stress. The objective of this study was to examine: (a) the changes in circulating calcium, parathyroid hormone (PTH) and calcitonin (CT) concentration in rats stressed by being given a subcutaneous injection of turpentine oil, and (b) the involvement of the sympathetic cervical pathway in stress-induced changes of calcium homeostasis. Four hours after receiving turpentine oil or vehicle, rats were subjected either to hypocalcemia, by being given EDTA intraperitoneally, or to hypercalcemia, by being injected CaCl2 intraperitoneally. Significant changes in serum calcium (10% decrease), serum PTH (28% increase) and CT levels (40% decrease) were observed in stressed rats. EDTA administration brought about a significantly greater hypocalcemia, and a higher PTH secretory response in turpentine oil-stressed rats. During stress, the increase of serum calcium after CaCl2 was significantly smaller, and the rise of CT was greater than in controls. In the case of CT the changes were still observed in rats subjected to superior cervical ganglionectomy (SCGx) 14 days earlier. In the case of PTH, the increase found in stressed rats, but not the augmented response after EDTA, was blunted by SCGx. The potentiation of hypocalcemia brought about by turpentine oil was no longer observed in SCGx rats. In vehicle-treated controls, SCGx delayed PTH response to hypocalcemia, but did not affect the increased response of CT to CaCl2 challenge. The results indicate that a number of changes in calcium homeostasis arise during turpentine oil stress in rats. SCGx was effective to modify the set point for PTH release, but played a minor role in affecting the augmentation of CT release during stress.

Transcutaneous electrical nerve stimulation (TENS) for phantom pain and stump pain following amputation in adults.

Science.gov (United States)

Johnson, Mark I; Mulvey, Matthew R; Bagnall, Anne-Marie

2015-08-18

This is the first update of a Cochrane review published in Issue 5, 2010 on transcutaneous electrical nerve stimulation (TENS) for phantom pain and stump pain following amputation in adults. Pain may present in a body part that has been amputated (phantom pain) or at the site of amputation (stump pain), or both. Phantom pain and stump pain are complex and multidimensional and the underlying pathophysiology remains unclear. The condition remains a severe burden for those who are affected by it. The mainstay treatments are predominately pharmacological, with increasing acknowledgement of the need for non-drug interventions. TENS has been recommended as a treatment option but there has been no systematic review of available evidence. Hence, the effectiveness of TENS for phantom pain and stump pain is currently unknown. To assess the analgesic effectiveness of TENS for the treatment of phantom pain and stump pain following amputation in adults. For the original version of the review we searched the Cochrane Central Register of Controlled Trials (CENTRAL), MEDLINE, EMBASE, PsycINFO, AMED, CINAHL, PEDRO and SPORTDiscus (February 2010). For this update, we searched the same databases for relevant randomised controlled trials (RCTs) from 2010 to 25 March 2015. We only included RCTs investigating the use of TENS for the management of phantom pain and stump pain following an amputation in adults. Two review authors independently assessed trial quality and extracted data. We planned that where available and appropriate, data from outcome measures were to be pooled and presented as an overall estimate of the effectiveness of TENS. In the original review there were no RCTs that examined the effectiveness of TENS for the treatment of phantom pain and stump pain in adults. For this update, we did not identify any additional RCTs for inclusion. There were no RCTs to judge the effectiveness of TENS for the management of phantom pain and stump pain. The published literature on TENS

Histological Changes in the Proximal and Distal Tendon Stumps Following Transection of Achilles Tendon in the Rabbits.

Science.gov (United States)

Al-Qattan, Mohammad M; Mawlana, Ola Helmi; Mohammed Ahmed, Raeesa Abdel-Twab; Hawary, Khalid

2016-05-01

To determine tendon stump changes following unrepaired Achilles tendon lacerations in an animal model. An experimental study. King Saud University, Riyadh, Saudi Arabia, from October 2013 to January 2014. Arabbit model was developed and studied tendon retraction and histological changes in the proximal and distal stumps following transection of the Achilles tendon. Over a period of 12 weeks, retraction of the distal tendon stump was minimal (2 - 3 mm). In contrast, retraction of the proximal tendon stump peaked to reach 6 mm at 4 weeks post-injury and plateaued to reach 7 - 8 mm at the 12-week interval. Following complete transection of the Achilles tendon, tendon retraction correlated with the density of myofibroblast expression within the tendon stump. Further research is needed to investigate the pathophysiology of these findings.

Appalachian hardwood stump sprouts are potential sawlog crop trees. Research note NE-299. [Oak, maple, linden, cherry trees

Energy Technology Data Exchange (ETDEWEB)

Lanson, N.I.

1976-01-01

Dbh and height of 8- and 12-year-old coppice shoots and the number of live shoots were recorded for 736 stumps at least 12 inches in diameter of Liriodendron tulipifera, Prunus serotina, Quercus rubra, Acer rubrum, and Tilia americana in north-central West Virgina. Of the 8-year-old shoots, T. americana had the greatest number of live stems/stump (16.8) and the greatest number of potential crop trees (dominant or co-dominant shoots attached to the stump not more than 6 inches above the ground), averaging 2.5 stems/stump. The average numbers of potential crop trees/stump were similar at 8 and 12 year. At 12 years, at least 88% of stumps of each species had at least one stem of groundline origin with no forks below 25 feet were 84% for L. tulipifera, 59% for Q rubra, 73% for A. rubrum, and 65% for P. Serotina.

Stabilization of the ulnar stump using modified Breen method after the Sauve-Kapandji procedure in rheumatoid wrist

International Nuclear Information System (INIS)

Tanino, Yoshihiko; Yabe, Yutaka; Yamauchi, Kenji; Ikegami, Hiroyasu; Ichikawa, Tooru

2006-01-01

We report on the utility of the modified Breen method in addition to the Sauve-Kapandji operation for the treatment of instability and pain in the proximal ulnar stump in rheumatoid arthrities (RA) wrist. We treated a total of 15 hands in 12 patients with disturbances due to instability and pain at the proximal ulnar stump. The average follow-up period was 47 months. We evaluated the range of motion, grip strength, radioulnar distance, and the radioulnar distance at the stump using CT during pronation, supination, and neutral positions of the forearm in 11 of the 15 operated hands. We observed that none of the patients showed any signs of pain at the proximal ulnar stump and no scallop sign was observed. In all the cases, the line connecting the center of the radial head to the proximal ulnar stump served as the axis of rotation for the forearm; this was confirmed by the CT images. We concluded that our operative method resulted in stabilization of the proximal ulnar stump and recovery of powerful grip without pain during forearm rotation. (author)

Histological Changes in the Proximal and Distal Tendon Stumps Following Transection of Achilles Tendon in the Rabbits

International Nuclear Information System (INIS)

Al-Qattan, M. M.; Hawary, K.; Mawlana, O. H.; Ahmed, R. A. M.

2016-01-01

Objective: To determine tendon stump changes following unrepaired Achilles tendon lacerations in an animal model. Study Design: An experimental study. Place and Duration of Study: King Saud University, Riyadh, Saudi Arabia, from October 2013 to January 2014. Methodology: Arabbit model was developed and studied tendon retraction and histological changes in the proximal and distal stumps following transection of the Achilles tendon. Result: Over a period of 12 weeks, retraction of the distal tendon stump was minimal (2 - 3 mm). In contrast, retraction of the proximal tendon stump peaked to reach 6 mm at 4 weeks post-injury and plateaued to reach 7 - 8 mm at the 12-week interval. Conclusion: Following complete transection of the Achilles tendon, tendon retraction correlated with the density of myofibroblast expression within the tendon stump. Further research is needed to investigate the pathophysiology of these findings. (author)

Growth of teak regenerated by coppice and stump planting in Mae Moh Plantation, Lampang province, Thailand

Directory of Open Access Journals (Sweden)

Anatta Auykim

2017-08-01

Full Text Available The current annual increment (CAIdbh and the mean annual increment (MAIdbh both for the diameter at breast height (1.3 m were investigated to compare the differences between coppice and stump-planted teak in Mae Moh Plantation. Forty-eight sample cores were collected from a 9 yr-old teak plantation using an increment borer; annual increments were analyzed using dendrochronological techniques. The results indicated that there was no significant (p > 0.05 difference in the average diameter at breast height (DBH between the coppice and stump-planted teak, whereas the total height of stump planting was significantly greater than that of coppice teak. The CAIdbh of coppice teak was in the range 0.316–2.371 cm and continuously decreased throughout the 9 yr period. The CAIdbh of stump planting was in the range 0.162–1.982 cm and continuously increased from the beginning of growth for 5 yr followed by a decline thereafter for 4 yr. The CAIdbh of coppice showed rapid growth in the years 1–4 and was greater than for the stump-planted teak even in years 5–8 after planting; however, the growth of the stump-planted teak in the ninth year was higher than for the coppice. The MAIdbh values of coppice and stump-planted teak were not significantly (p > 0.05 different. The results showed that CAIdbh at age 5 yr can be used as a silvicultural guide to increase the yield of teak coppice.

The effects of adrenal hormones, endotoxin and turpentine on serum components of the plaice (Pleuronectes platessa L.).

Science.gov (United States)

White, A; Fletcher, T C

1982-01-01

1. Within 24 hr of injection into plaice, cortisol, deoxycorticosterone, adrenalin or endotoxin cause an increase (P less than 0.001) in circulating C-reactive protein (CRP). Turpentine and soluble dexamethasone have no effect. 2. The increase in CRP with endotoxin is not enhanced with adrenalin or deoxycorticosterone, and in conjunction with cortisol the increase is additive. 3. Changes in CRP are independent of the amounts of serum amyloid P-component or total protein. 4. Turpentine, cortisol and adrenalin cause a rapid increase in circulating glucose. 5. It is concluded that some adrenal hormones stimulate the CRP acute phase response in plaice, without an apparent provoking agent.

Geographical variance in the risk of gastric stump cancer: no increased risk in Japan?

NARCIS (Netherlands)

Tersmette, A. C.; Giardiello, F. M.; Offerhaus, G. J.; Tersmette, K. W.; Ohara, K.; Vandenbroucke, J. P.; Tytgat, G. N.

1991-01-01

Geographical differences may exist in the risk of gastric stump cancer. Therefore, we performed meta-analysis of literature reports in Japan (n = 3), the USA (n = 4), and Europe (n = 20) on the risk of postgastrectomy cancer. The weighted mean relative risk of stump cancer in Japan was 0.28, 95%

Stump entrapment of the anterior cruciate ligament in late childhood and adolescence

Energy Technology Data Exchange (ETDEWEB)

Meyers, Arthur B.; Laor, Tal; Zbojniewicz, Andrew M. [Cincinnati Children' s Hospital Medical Center, Department of Radiology, Cincinnati, OH (United States)

2011-08-15

Displacement of a portion of the torn anterior cruciate ligament (ACL) into the intercondylar notch can cause a focal fibrotic reaction similar to that seen following ACL reconstruction. This displacement, which can result in locking or limitation of knee extension, is termed stump entrapment and is described in adult MR imaging literature. We present a pictorial essay of the etiology and appearance of stump entrapment on MR imaging of the knee in an older child and adolescents and review the significance of this finding. (orig.)

Glenohumeral interposition of rotator cuff stumps: a rare complication of traumatic rotator cuff tear

Directory of Open Access Journals (Sweden)

Paulo Moraes Agnollitto

2016-02-01

Full Text Available Abstract The present report describes a case where typical findings of traumatic glenohumeral interposition of rotator cuff stumps were surgically confirmed. This condition is a rare complication of shoulder trauma. Generally, it occurs in high-energy trauma, frequently in association with glenohumeral joint dislocation. Radiography demonstrated increased joint space, internal rotation of the humerus and coracoid process fracture. In addition to the mentioned findings, magnetic resonance imaging showed massive rotator cuff tear with interposition of the supraspinatus, infraspinatus and subscapularis stumps within the glenohumeral joint. Surgical treatment was performed confirming the injury and the rotator cuff stumps interposition. It is important that radiologists and orthopedic surgeons become familiar with this entity which, because of its rarity, might be neglected in cases of shoulder trauma.

Rooting stem cuttings of northern red oak (Quercus rubra L.) utilizing hedged stump sprouts formed on recently felled trees

Science.gov (United States)

Matthew H. Gocke; Daniel J. Robinson

2010-01-01

The ability to root stem cuttings collected from hedged stump sprouts formed on recently felled trees was evaluated for 26 codominant northern red oak (Quercus rubra L.) trees growing in Durham County, NC. Sprouting occurred, the same year as felling, on 23 of the 26 tree stumps and sprout number was significantly and positively correlated with stump diameter. The...

Profitability of Precommericially Thinning Oak Stump Sprouts

Science.gov (United States)

John P. Dwyer; Daniel C. Dey; William B. Kurtz

1993-01-01

Thinning oak stump sprouts to a single stem at an early age will increase diameter growth of the released stem. However, percommercial thinning represents a substantial investment which must be carried for many years before any returns are realized. We estimated the incremental gains in yield and the present net worth for five crop-tree release treatments of 5-yr-old...

Profitability of precommercially thinning oak stump sprouts

Science.gov (United States)

John P. Dwyer; Daniel C. Dey; William B. Kurtz

1993-01-01

Thinning oak stump sprouts to a single stem at an early age will increase diameter growth of the released stem. However, precommercial thinning represents a substantial investment which must be carried for many years before any returns are realized. We estimated the incremental gains in yield and the present net worth for five crop-tree release treatments of 5-year-old...

Relationship of stump diameter to d.b.h. for white pine in the northeast

Science.gov (United States)

Jesse D. Diller

1954-01-01

A need to estimate the volume cut from a timber tract when only the stumps are left is often felt by foresters, timber operators, and landowners. This need arises in areas where timber sales are based on stump diameters, in timber trespass cases, in check cruises on marked timber sales (to determine volume cut from unmarked trees), and as an aid in piecing together the...

Effects of season and urea treatment on infection of stumps of Picea abies by Heterobasidion annosum in stands on former arable land

Energy Technology Data Exchange (ETDEWEB)

Brandtberg, P.O. [Swedish Univ. of Agricultural Sciences, Uppsala (Sweden). Dept. of Ecology and Environmental Research; Johansson, Martin [Swedish Univ. of Agricultural Sciences, Uppsala (Sweden). Dept. of Forest Mycology and Pathology; Seeger, P. [Swedish Univ. of Agricultural Sciences, Uppsala (Sweden). Dept. of Statistics

1996-09-01

Between 1986 and 1990, a series of thinnings were made in previously unthinned first rotation stands on former arable land located in the southern half of Sweden. The aim was to evaluate the effects of season and urea treatment on the frequency of infection of stumps of Norway spruce (Picea abies (L.) Karst.) by the root-rot fungus Heterobasidion annosum (Fr.) Bref. Untreated stumps, resulting from 60 thinnings (22-100 stumps each, altogether ca 3000 stumps) made at different times of year, were investigated 3-24 months after cutting to determine whether they were infected with H. annosum. On average only 2% of the stumps from thinnings made in November-February were infected, whereas the incidence of infection among stumps thinned in June-July was 34%. Two methods of treating stumps with urea to prevent stump infection by H. annosum after thinning were evaluated in terms of effectiveness. The freshly cut stumps were treated with a 20% urea solution, transformed to a gel by adding 0.2% carboxymethyl cellulose, or with a 30% urea solution. On average, the reduction in infection rate obtained was 62% with the first method and 85% with the latter. In a separate study involving a concentration series of urea, there was a considerable drop in protection efficiency, from 89% to 58%, when the concentration was decreased from 30% to 15%. 38 refs, 3 figs, 1 tab

Rectosigmoid stump washout as an alternative to permanent mucous fistula in patients undergoing subtotal colectomy for ulcerative colitis in emergency settings.

Science.gov (United States)

Pellino, Gianluca; Sciaudone, Guido; Candilio, Giuseppe; Canonico, Silvestro; Selvaggi, Francesco

2012-01-01

Restorative proctocolectomy with ileopouch-anal anastomosis (IPAA) is the treatment of choice for intractable or complicated ulcerative colitis(UC). Elderly patients often present with acute colitis requiring emergent subtotal colectomy(SC). Frail patients are at risk of developing septic complications related to the closed rectosigmoidal stump, often requiring formation of a second stoma to be reversed at the time of completion proctectomy. This carries nuisance to such exhausted patients. We propose a simple and inexpensive trick to avoid the need for creating a mucous fistula. IPAA was performed as a 3-stage procedure in emergency settings. The rectosigmoidal stump was closed and placed subcutaneously; skin was closed over it. After SC, if patients showed signs of stump-related pelvic sepsis, a lavage of the rectal stump with povidone iodine solution and with saline was carried out as a rescue treatment aiming to avoid the need of opening the rectal stump to drain sepsis. Thirty-five patients underwent SC for UC between 1987 and 2012. The skin was closed over the closed stump in the 20. Seven patients out of these 20 experienced early stump-related septic complication. In five cases, we were able to avoid opening of the rectal stump, and a second stoma was unnecessary. After opening the closed stump in the remaining ones, a prompt improving of symptoms was observed. Rectal washout was well tolerated and avoided a second stoma in five out of seven patients, with better quality of life and body perception after IPAA surgery. This is relevant when dealing with geriatric patients, needing to completely recover before undergoing completion proctectomy.

Comparison of topical capsaicin and topical turpentine oil for treatment of painful diabetic neuropathy

International Nuclear Information System (INIS)

Musharraf, M.U.; Ahmed, Z.

2017-01-01

Background: Diabetes Mellitus is a pandemic of the modern era owing to our rapidly deteriorating lifestyle. Painful diabetic neuropathy is one of the costliest and disabling complications of diabetes mellitus. No single treatment exists to prevent or reverse neuropathic changes or to provide total pain relief. Topical Capsaicin and Turpentine Oil are found to be effective in treatment of painful diabetic neuropathy. Methods: Patients of either gender with ages between 18 and 70 years having painful diabetic neuropathy already taking one oral drug for painful neuropathy and treatment for diabetes mellitus and an HbA1C less than 8.5% were included while Pregnant or lactating mothers, patients with chronic liver disease and patients with renal insufficiency (creatinine >3.0 mg/dl) and peripheral arterial disease were excluded from study. Patients were randomly divided into two groups (A and B) using computer generated random number table. Group A was given topical application of capsaicin while Group B was given topical application of commercially available turpentine oil over painful site on feet. Results: 300 patients were equally divided in two groups. The patients in group A had a Visual Analog Pain Score of 7.91±5.10 at baseline and 5.10±1.343 after 3 months of treatment (p-value 0.0001). The patients in group B had a Visual Analog Pain Score of 7.83±1.012 at baseline and 5.20±1.187 after 3 months of treatment (p-value 0.0001). Chi Square test was applied to compare efficacy of both groups. It was noted that 71 (53%) had efficacy in group A and 63 (47%) had efficacy in the group B but the difference was not statistically significant. (p-value=0.399). Conclusion: It has been concluded that turpentine oil is effective in managing diabetic neuropathic pain similar to capsaicin cream.

Stump appendicitis 10 years after appendectomy, a rare, but serious complication of appendectomy, a case report.

Science.gov (United States)

Van Paesschen, Carl; Haenen, Filip; Bestman, Raymond; Van Cleemput, Marc

2017-02-01

We describe a case of stump appendicitis with the formation of abdominal abscesses in a 41-year-old patient 10 years prior appendectomy. The patient consulted with fever (38.1 °C) and abdominal pain, located at the right iliac fossa. Imaging studies showed signs of abscesses, located at the right iliac fossa, without clear origin of these abscesses. The abscesses were drained through diagnostic laparoscopy, no bowel perforation or clear origin of the abscedation was found during laparoscopy. During postoperative stay, the inflammatory parameters rose and the abscesses reoccurred. Re-laparoscopy was performed, the abscesses were drained and on careful inspection and adhesiolysis, a perforated stump appendicitis was revealed, covered underneath layers of fibrous tissue. Stump appendicitis is a rare complication seen after appendectomy and is generally not considered a possible etiology in patients presenting with fever and right iliac fossa abdominal pain with a history of appendectomy. This often delays the correct diagnosis and results in an associated increased incidence of complications. We describe a case of stump appendicitis occurring 10 years after initial appendectomy.

How to Distinguish Attacks by the Black Turpentine Beetle and Dioryctria Amatella on Southern Pines

Science.gov (United States)

Carl W. Fatzinger; Gary L. DeBarr

1969-01-01

Trunk attacks by the black turpentine beetle, Dendroctonus terebrans (Oh.), and the larvae of Dioryctria amatella (Hulst) on the southern pines results in a copious flow of pitch. This external pitch mass or pitch tube exhibits characteristics that can be used as symptoms to distinguish between attacks by these two insects.

Red Turpentine Beetle, Dendroctonus valens LeConte (Coleoptera: Scolytidae), Response to Host Semiochemicals in China

Science.gov (United States)

Jianghua Sun; Zhengwan Miao; Zhen Zhang; Zhongning Zhan; Nancy Gillette

2004-01-01

The response of the introduced red turpentine beetle, Dendroctonus valens LeConte, to host semiochemicals in Shanxi Province, China, was distinctly different from that reported in previous studies conducted in the western part of the native range of D. valens in the central Sierra Nevada, CA. This Þnding suggests either that...

Susceptibility of three clinical isolates of Actinomodura madurae to α-pinene, the bioactive agent of Pinus pinaster turpentine oil

Directory of Open Access Journals (Sweden)

Stojković D.

2008-01-01

Full Text Available In vitro susceptibility of the turpentine oil obtained from Pinus pinaster oleoresin was evaluated against three Sudanese clinical isolates of Actinomadura madurae, which is the main causative agent of actinomycetoma. The minimum inhibitory concentrations (MICs of the oil ranged from 100.3 to 124.8 μL/mL, and the minimum microbicidal concentrations (MMCs were between 100.3 and 150.0 μL/mL. α-Pinene exhibited prominent bioactivity with MICs ranging between 3.3 and 5.0 μL/mL, while its MMC was 10.0 μL/mL against the same clinical isolates. Pinus pinaster turpentine oil and α-pinene might be useful agents in the treatment of mycetoma caused by A. madurae.

Management of the difficult duodenal stump in penetrating duodenal ulcer disease: a comparative analysis of duodenojejunostomy with "classical" stump closure (Nissen-Bsteh).

Science.gov (United States)

Vashist, Yogesh K; Yekebas, Emre F; Gebauer, Florian; Tachezy, Michael; Bachmann, Kai; König, Alexandra; Kutup, Asad; Izbicki, Jakob R

2012-12-01

Duodenal stump insufficiency after surgery for penetrating gastroduodenal ulcer is associated with substantial mortality. "Classical" technique of closing a difficult duodenal stump (Nissen-Bsteh) has, up to now, not been compared with duodenojejunostomy (DJ) in larger patient sets. This also refers to the potential benefit of a gastric and biliary diversion under such conditions. The aim of the present study was to compare classical duodenal closure (CC) with DJ and to evaluate the impact of gastric and biliary diversion on postoperative outcome after surgery for penetrating, high-risk duodenal ulcer in a matched control study. Out of 321 patients, treated for penetrating duodenal ulcer disease, the perioperative outcome of 62 DJ patients was compared with 62 patients undergoing CC matched for age, gender, biliary diversion, and the operating surgeon collective. A total of 70 patients, equally distributed between DJ and CC subsets, received temporary biliary diversion. Overall perioperative mortality was 10.5%. However, DJ significantly reduced the mortality rate (4.8%) associated with penetrating duodenal ulcer compared to CC (16.1%, P management of penetrating duodenal ulcer.

Synthesis of Biokerosene through Electrochemical Hydrogenation of Terpene Hydrocarbons from Turpentine Oil

Directory of Open Access Journals (Sweden)

Tedi Hudaya

2016-12-01

Full Text Available Indonesia possesses great potential for developing renewable resources as alternative fuels. For example, turpentine oil obtained from Pinus merkusii, which contains mostly monoterpene hydrocarbons (C10H16. The oil is highly suitable to be processed for biokerosene or even jet biofuel. It consists of hydrocarbons within the range of C10 to C15. However, it contains insufficient H and thus needs to be upgraded. In the present work, electrochemical hydrogenation was used for upgrading. In the electrochemical cell, stainless steel, silver, and carbon were used alternately for the anode, while copper and silver Raschig rings were used for the cathode. An electrolyte solution of cuprous ammonium formate was utilized not only as a source of H but also to draw the unsaturated hydrocarbons into the aqueous phase. The electrolyte : oil ratio (up to 2:1, electrolyte concentration (between 0.4 and 2 M and reaction time were varied throughout the experiments. The bromine number (unsaturation level of the turpentine oil, which was initially 1,86 (mole Br2/mole, was lowered significantly to 0.69-0.90. Promising increase of smoke point values were observed from 11 mm to 16-24 mm, indicating a higher H content of the processed oil, thus making it suitable as a substitute for petroleum kerosene.

Preliminary test of two stump surface protectants against Fomes annosus.

Science.gov (United States)

E.E. Nelson; C.Y. Li

1980-01-01

Two materials, monolaurin (at two concentrations) and an unidentified species of the genus Streptomyces, were tested along with borax for ability to protect freshly cut stump surfaces of western hemlock (Tsuga heterophylla (Raf.) Sarg.) from colonization by Fomes annosus. Protectants were significantly (P...

Risk Factors for Rectal Stump Cancer in Inflammatory Bowel Disease

NARCIS (Netherlands)

Lutgens, M.W.M.D.; van Oijen, M.G.H.; Vleggaar, F.P.; Siersema, P.D.; Broekman, M.M.T.J.; Oldenburg, B.; van Bodegraven, A.A.; Dijkstra, G.; Hommes, D.; de Jong, D.J.; Stokkers, P.C.F.; van der Woude, C.J.

2012-01-01

BACKGROUND: Patients with long-standing colitis carry an increased risk of colorectal cancer and are therefore enrolled in colonoscopic surveillance programs. It is presently not known if endoscopic surveillance of patients with colitis with a closed rectal stump after a subtotal colectomy is

Risk factors for rectal stump cancer in inflammatory bowel disease.

NARCIS (Netherlands)

Lutgens, M.W.; Oijen, M.G.H. van; Vleggaar, F.P.; Siersema, P.D.; Broekman, M.M.T.J.; Oldenburg, B.

2012-01-01

BACKGROUND: Patients with long-standing colitis carry an increased risk of colorectal cancer and are therefore enrolled in colonoscopic surveillance programs. It is presently not known if endoscopic surveillance of patients with colitis with a closed rectal stump after a subtotal colectomy is

Carcinoma of the cervical stump: comparison of radiation therapy factors, survival and patterns of failure with carcinoma of the intact uterus

International Nuclear Information System (INIS)

Igboeli, P.; Kapp, D.S.; Lawrence, R.; Schwartz, P.E.

1983-01-01

Eighty-nine patients with previously untreated invasive carcinoma of the cervical stump were seen at Yale-New Haven Hospital from 1953 through 1977. This represented 9.4% of the carcinomas of the cervix seen during this time period. Eighty-five of the 89 patients (95.5%) had ''true'' cancers of the cervical stump diagnosed 2 years or more after subtotal hysterectomy, while 4 of the 89 patients (4.5%) had ''coincident'' cancers diagnosed within 2 years of the subtotal hysterectomy. All cervical cancers were staged by the F.I.G.O. classification. Patient characteristics, methods of management, failure sites and survival of patients with carcinoma of the cervical stump were compared to those patients with carcinoma in the intact uterus. Patients with cervical stump cancers were treated in a similar manner to those with carcinomas of the intact uterus, using a combination of external beam irradiation and intracavitary radium. The stump cancer patients had a similar stage distribution to the patients with cancers of the intact uterus but, on the average, they were older and received less irradiation. The patterns of failure were similar on a stage for stage basis, but the survival and disease-free survival for stump cancer patients were superior to those of the patients with carcinoma of the intact uterus

Surface-based GPR underestimates below-stump root biomass

Science.gov (United States)

John R. Butnor; Lisa J. Samuelson; Thomas A. Stokes; Kurt H. Johnsen; Peter H. Anderson; Carlos A. Gonzalez-Benecke

2016-01-01

Aims While lateral root mass is readily detectable with ground penetrating radar (GPR), the roots beneath a tree (below-stump) and overlapping lateral roots near large trees are problematic for surface-based antennas operated in reflection mode. We sought to determine if tree size (DBH) effects GPR root detection proximal to longleaf pine (Pinus palustris Mill) and if...

Evaluation of home care management of umbilical cord stumps by ...

African Journals Online (AJOL)

Background: Umbilical cord care is an integral part of neonatal care in all communities and cultures and appropriate cord care reduces the risk of infection in the newborn infant. Objective: The present study assessed the home care management of the umbilical stump by the mothers at Ilesa, Southwestern Nigeria. Subjects ...

Concentrations of base cations, phosphorous and nitrogen in tree stumps in Sweden, Finland and Denmark; Halter av baskatjoner, fosfor och kvaeve i stubbar i Sverige, Finland och Danmark

Energy Technology Data Exchange (ETDEWEB)

Hellsten, Sofie; Waengberg, Ingvar (The Swedish Environmental Research Institute Ltd., Stockholm (Sweden)); Helmisaari, Heljae-Sisko; Kaakinen, Seija; Kukkola, Mikko; Saarsalmi, Anna (Metla, Vantaa (Finland)); Melin, Ylva; Petersson, Hans (Swedish Univ. of Agriculture, Umeaa (Sweden)); Skovsgaard, Jens Peter (Forest and Landscape Denmark, Univ. of Copenhagen, Hoersholm (Denmark)); Akselsson, Cecilia (Lunds Univ., Lund (Sweden))

2009-05-15

Stump removal is becoming increasingly important in as demand for renewable energy is increasing. Nutrient concentrations in stumps are applied when evaluating the environmental effect of stump removal on acidification and nutrient balances in forest soil. The objectives of this study was to evaluate concentrations of nutrients in stumps in Sweden, Finland and Denmark, and to evaluate how nutrient concentrations vary with site characteristics, stand age and deposition level. Concentrations of N, P, Ca, K, Mg and Na in spruce, pine and birch stumps were assessed in eight sites across Scandinavia. The results of this study indicate that the concentration of nutrients are higher in birch stumps compared with spruce and pine. In Sweden and Finland, the nutrient concentrations were generally higher in the southern sites compared with northern sites in the country, except for P. Nutrient concentrations were significantly higher in the bark of the stump and the roots compared to the wood for all nutrients. Furthermore nutrients concentration increased significantly with decreasing root diameter. In Jaedraaas, Sweden, nutrient concentration of N, K, Mg and P in pine decreased with age of the stump harvested tree, for stumps < 65 years. This relation was not evident for other age spans or sites. Further studies are needed to provide a broader picture of how the nutrient concentrations vary with site characteristics, stand age and forestry management to get a better foundation when setting up recommendations for stump removal

Prediction and error of baldcypress stem volume from stump diameter

Science.gov (United States)

Bernard R. Parresol

1998-01-01

The need to estimate the volume of removals occurs for many reasons, such as in trespass cases, severance tax reports, and post-harvest assessments. A logarithmic model is presented for prediction of baldcypress total stem cubic foot volume using stump diameter as the independent variable. Because the error of prediction is as important as the volume estimate, the...

Occupational Exposure to Mineral Turpentine and Heavy Fuels: A Possible Risk Factor for Alzheimer's Disease

Directory of Open Access Journals (Sweden)

Rafik Helou

2014-06-01

Full Text Available Background: The association between solvents and Alzheimer's disease (AD has been the subject of several studies. Yet, only few studies have examined the various solvents separately, and the controls have rarely been monitored long enough. For these reasons and others, we believe that further studies are required. Objectives: The objective of this study was to identify solvents associated with the clinicoradiological diagnostic of AD or mixed-type dementia (MD. Methods: A retrospective case-control study was performed in 156 patients followed up at the Memory Diagnostic Center of Bertinot Juel Hospital (France. The inclusion criteria were known occupation(s, a Mini-Mental State Examination (MMSE score ≥10 at the first visit, a neuropsychological evaluation performed and a diagnosis established in our Memory Diagnostic Center. The diagnostics were crossed with 9 solvents belonging to two classes of solvents. Exposure was evaluated using French national job-exposure matrices. Results: Certain petroleum-based solvents and fuels (i.e. mineral turpentine, diesel fuel, fuel oil and kerosene were associated with a diagnosis of AD or MD. This association was still significant after adjustment for age, sex and education (adjusted OR: 6.5; 95% CI: 2-20. Conclusion: Occupational exposure to mineral turpentine and heavy fuels may be a risk factor for AD and MD.

Digital artery perforator (DAP) flaps: modifications for fingertip and finger stump reconstruction.

Science.gov (United States)

Mitsunaga, Narushima; Mihara, Makoto; Koshima, Isao; Gonda, Koichi; Takuya, Iida; Kato, Harunosuke; Araki, Jun; Yamamoto, Yushuke; Yuhei, Otaki; Todokoro, Takeshi; Ishikawa, Shoichi; Eri, Uehara; Mundinger, Gerhard S

2010-08-01

Various fingertip reconstructions have been reported for situations where microsurgical finger replantation is impossible. One method is the digital artery perforator (DAP) flap. Herein we report 13 DAP flaps for fingertip and finger stump reconstruction following traumatic finger amputations, highlighting modifications to the originally described DAP flap. From October 1998 to December 2007, a total of 13 fingers (11 patients) underwent fingertip and finger stump reconstruction with modified DAP flaps following traumatic finger amputations. We performed six adipocutaneous flaps, three adipose-only flaps, two supercharged flaps and two extended flaps. Flap size ranged from 1.44 to 8 cm(2) (average 3.25 cm(2)). All flaps survived completely with the exception of partial skin necrosis in two cases. One of these cases required debridement and skin grafting. Our initial three cases used donor-site skin grafting. The donor site was closed primarily in the 10 subsequent cases. No patients showed postoperative hypersensitivity of repaired fingertips. Semmes-Weinstein (SW) test result for flaps including a digital nerve branch did not differ from those without (average 4.07 vs. 3.92). Modified DAP flaps allow for preservation of digital length, volume and finger function. They can be raised as adiposal-only flaps or extended flaps and supercharged through perforator-to-perforator anastomoses. The donor defect on the lateral pulp can be closed primarily or by skin grafting. For traumatic fingertip and finger stump reconstructions, DAP flaps deliver consistent aesthetic and functional results. Copyright 2009 British Association of Plastic, Reconstructive and Aesthetic Surgeons. Published by Elsevier Ltd. All rights reserved.

SOUND VELOCITY and Other Data from USS STUMP DD-978) (NCEI Accession 9400069)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The sound velocity data in this accession were collected from USS STUMP DD-978 by US Navy. The sound velocity in water is analog profiles data that was recorded in...

New Models for Predicting Diameter at Breast Height from Stump Dimensions

Science.gov (United States)

James A. Westfall

2010-01-01

Models to predict dbh from stump dimensions are presented for 18 species groups. Data used to fit the models were collected across thirteen states in the northeastern United States. Primarily because of the presence of multiple measurements from each tree, a mixed-effects modeling approach was used to account for the lack of independence among observations. The...

Self-Expandable Stenting over a Stent Graft for the Exclusion of a Carotid Stump: Troubleshooting for Device Incompatibility

International Nuclear Information System (INIS)

Youn, Sung Won; Kim, Ho Kyun; Do, Jin Kook; Kim, Young Whan

2011-01-01

Carotid stump, the blind remnant of an occluded internal carotid artery, can be a potential source of microemboli, and warrants its exclusion from the vascular lumen to prevent the recurrence of a microembolism. In a 69-year-old male with a symptomatic carotid stump and acute angle between left common carotid artery and aortic arch, a 7-Fr. shuttle sheath was scarcely placed into the left carotid artery but the 7-mm-diameter stent-graft-loading balloon could not be inserted into the 7-Fr. shuttle sheath. With the mounting a stent graft over a 5-mm balloon, the balloon-expandable stent graft was unfolded. The self-expandable stent was placed over the stent graft, and an 8-mm balloon was subsequently expanded. Self-expanding stenting can be useful for troubleshooting in a case of device incompatibility coming from the different calibers of the external and common carotid arteries for the successful exclusion of a symptomatic carotid stump.

Self-Expandable Stenting over a Stent Graft for the Exclusion of a Carotid Stump: Troubleshooting for Device Incompatibility

Energy Technology Data Exchange (ETDEWEB)

Youn, Sung Won; Kim, Ho Kyun [Dept. of Radiology, Catholic University of Daegu School of Medicine, Daegu (Korea, Republic of); Do, Jin Kook [Dept. of Neurology, Catholic University of Daegu School of Medicine, Daegu (Korea, Republic of); Kim, Young Whan [Dept. of Radiology, University College of Medicine, Daegu (Korea, Republic of)

2011-12-15

Carotid stump, the blind remnant of an occluded internal carotid artery, can be a potential source of microemboli, and warrants its exclusion from the vascular lumen to prevent the recurrence of a microembolism. In a 69-year-old male with a symptomatic carotid stump and acute angle between left common carotid artery and aortic arch, a 7-Fr. shuttle sheath was scarcely placed into the left carotid artery but the 7-mm-diameter stent-graft-loading balloon could not be inserted into the 7-Fr. shuttle sheath. With the mounting a stent graft over a 5-mm balloon, the balloon-expandable stent graft was unfolded. The self-expandable stent was placed over the stent graft, and an 8-mm balloon was subsequently expanded. Self-expanding stenting can be useful for troubleshooting in a case of device incompatibility coming from the different calibers of the external and common carotid arteries for the successful exclusion of a symptomatic carotid stump.

The capability of fiber Bragg grating sensors to measure amputees' trans-tibial stump/socket interface pressures.

Science.gov (United States)

Al-Fakih, Ebrahim A; Osman, Noor Azuan Abu; Eshraghi, Arezoo; Adikan, Faisal Rafiq Mahamd

2013-08-12

This study presents the first investigation into the capability of fiber Bragg grating (FBG) sensors to measure interface pressure between the stump and the prosthetic sockets of a trans-tibial amputee. FBG element(s) were recoated with and embedded in a thin layer of epoxy material to form a sensing pad, which was in turn embedded in a silicone polymer material to form a pressure sensor. The sensor was tested in real time by inserting a heavy-duty balloon into the socket and inflating it by using an air compressor. This test was conducted to examine the sensitivity and repeatability of the sensor when subjected to pressure from the stump of the trans-tibial amputee and to mimic the actual environment of the amputee's Patellar Tendon (PT) bar. The sensor exhibited a sensitivity of 127 pm/N and a maximum FSO hysteresis of around ~0.09 in real-time operation. Very good reliability was achieved when the sensor was utilized for in situ measurements. This study may lead to smart FBG-based amputee stump/socket structures for pressure monitoring in amputee socket systems, which will result in better-designed prosthetic sockets that ensure improved patient satisfaction.

The Capability of Fiber Bragg Grating Sensors to Measure Amputees’ Trans-Tibial Stump/Socket Interface Pressures

Directory of Open Access Journals (Sweden)

Faisal Rafiq Mahamd Adikan

2013-08-01

Full Text Available This study presents the first investigation into the capability of fiber Bragg grating (FBG sensors to measure interface pressure between the stump and the prosthetic sockets of a trans-tibial amputee. FBG element(s were recoated with and embedded in a thin layer of epoxy material to form a sensing pad, which was in turn embedded in a silicone polymer material to form a pressure sensor. The sensor was tested in real time by inserting a heavy-duty balloon into the socket and inflating it by using an air compressor. This test was conducted to examine the sensitivity and repeatability of the sensor when subjected to pressure from the stump of the trans-tibial amputee and to mimic the actual environment of the amputee’s Patellar Tendon (PT bar. The sensor exhibited a sensitivity of 127 pm/N and a maximum FSO hysteresis of around ~0.09 in real-time operation. Very good reliability was achieved when the sensor was utilized for in situ measurements. This study may lead to smart FBG-based amputee stump/socket structures for pressure monitoring in amputee socket systems, which will result in better-designed prosthetic sockets that ensure improved patient satisfaction.

Immobilization of spent resin with epoxy resin

International Nuclear Information System (INIS)

Gultom, O.; Suryanto; Sayogo; Ramdan

1997-01-01

immobilization of spent resin using epoxy resin has been conducted. The spent resin was mixtured with epoxy resin in variation of concentration, i.e., 30, 40, 50, 60, 70 weight percent of spent resin. The mixture were pour into the plastic tube, with a diameter of 40 mm and height of 40 mm. The density, compressive strength and leaching rate were respectively measured by quanta chrome, paul weber apparatus and gamma spectrometer. The results showed that the increasing of waste concentration would be decreased the compressive strength, and increased density by immobilized waste. The leaching rate of 137 Cs from waste product was not detected in experiment (author)

Stump-to-mill timber production cost equations for cable logging eastern hardwoods

Science.gov (United States)

Chris B. LeDoux; Chris B. LeDoux

1985-01-01

Logging cost simulators and data from logging cost studies have been assembled and converted into a series of equations that can be used to estimate the stump-to-mill cost of cable logging in mountainous terrain in the Eastern United States. These equations include the use of two small and four mediumsize cable yarders and are appropriate for harvested trees ranging in...

Combined analysis of cortical (EEG) and nerve stump signals improves robotic hand control.

Science.gov (United States)

Tombini, Mario; Rigosa, Jacopo; Zappasodi, Filippo; Porcaro, Camillo; Citi, Luca; Carpaneto, Jacopo; Rossini, Paolo Maria; Micera, Silvestro

2012-01-01

Interfacing an amputee's upper-extremity stump nerves to control a robotic hand requires training of the individual and algorithms to process interactions between cortical and peripheral signals. To evaluate for the first time whether EEG-driven analysis of peripheral neural signals as an amputee practices could improve the classification of motor commands. Four thin-film longitudinal intrafascicular electrodes (tf-LIFEs-4) were implanted in the median and ulnar nerves of the stump in the distal upper arm for 4 weeks. Artificial intelligence classifiers were implemented to analyze LIFE signals recorded while the participant tried to perform 3 different hand and finger movements as pictures representing these tasks were randomly presented on a screen. In the final week, the participant was trained to perform the same movements with a robotic hand prosthesis through modulation of tf-LIFE-4 signals. To improve the classification performance, an event-related desynchronization/synchronization (ERD/ERS) procedure was applied to EEG data to identify the exact timing of each motor command. Real-time control of neural (motor) output was achieved by the participant. By focusing electroneurographic (ENG) signal analysis in an EEG-driven time window, movement classification performance improved. After training, the participant regained normal modulation of background rhythms for movement preparation (α/β band desynchronization) in the sensorimotor area contralateral to the missing limb. Moreover, coherence analysis found a restored α band synchronization of Rolandic area with frontal and parietal ipsilateral regions, similar to that observed in the opposite hemisphere for movement of the intact hand. Of note, phantom limb pain (PLP) resolved for several months. Combining information from both cortical (EEG) and stump nerve (ENG) signals improved the classification performance compared with tf-LIFE signals processing alone; training led to cortical reorganization and

Intercostal muscle flap to protect the bronchial stump in pediatric lobectomy for lung abscess.

Science.gov (United States)

Lisi, Gabriele; Lauriti, Giuseppe; Cascini, Valentina; Lococo, Achille; Chiesa, Pierluigi Lelli

2013-01-01

Lung suppurative diseases in children are usually responsive to medical treatment or percutaneous drainage. Rarely, pulmonary resection is required for lung abscess in childhood, particularly in presence of co-morbidities. In these cases, a lobectomy is usually performed through an open thoracotomy, with a reported incidence of bronco-pleural fistula up to 9.1% of pediatric series. This consequence is mainly due to the inflammatory condition; however the lack of knowledge of pediatric and thoracic surgeons with this rare condition in childhood can also play a role. In adults with lung cancer, the buttressing of bronchial stump with the additional support of an intercostal muscle (ICM) flap has proved to prevent this complication, as well as to reduce post-operative pain. We report the first pediatric experience of ICM flap used in 2 immunocompetent children requiring lobectomy for suppurative lung conditions. Our preliminary experience confirms the feasibility of protecting the bronchial stump after lobectomy in children, especially in conditions at risk for bronco-pleural fistula development.

Resin impregnation process for producing a resin-fiber composite

Science.gov (United States)

Palmer, Raymond J. (Inventor); Moore, William E. (Inventor)

1994-01-01

Process for vacuum impregnation of a dry fiber reinforcement with a curable resin to produce a resin-fiber composite, by drawing a vacuum to permit flow of curable liquid resin into and through a fiber reinforcement to impregnate same and curing the resin-impregnated fiber reinforcement at a sufficient temperature and pressure to effect final curing. Both vacuum and positive pressure, e.g. autoclave pressure, are applied to the dry fiber reinforcement prior to application of heat and prior to any resin flow to compact the dry fiber reinforcement, and produce a resin-fiber composite of reduced weight, thickness and resin content, and improved mechanical properties. Preferably both a vacuum and positive pressure, e.g. autoclave pressure, are also applied during final curing.

[Lower limb stump reconstruction with a functional calcaneo-plantar unit free flap. A series of 16 cases].

Science.gov (United States)

Malikov, S; Dubert, T; Koupatadze, D; Nabokov, V; Polosov, R

1999-04-01

The main objective of surgery, once amputation is inevitable, is to preserve a functional stump. This report describes the immediate reconstruction of 16 leg stumps in children by transfer of a functional calcaneo-plantar unit. Of these, 3 were thigh and 13 were lower leg reconstructions. Amputation was performed for tumor in 4 cases, and was due to accidents in the remaining twelve. The main technical features of flap preparation are preservation of the calcaneum branch and attachment of the heel skin to the greater tuberosity of the calcaneum. One case resulted in failure due to vascular thrombosis. The other 15 cases resulted in bone consolidation after an average of 45 days, sensitive protection by 70 days, and very good trophic and protective results. The provision of good distal pressure area encourages overall development of the child. There was no morbidity at the donor site, and because there is no major muscle mass in the distal fragment, the overall risk is very low compared to that of total proximal leg replantation. The transfer of functional calcaneo-plantar tissue as a single unit is the best strategy for one-step restoration of good distal support area for the stump. All surgeons liable to perform leg amputations should be aware of this technical approach.

Eradicative brachytherapy with hyaluronate gel injection into pararectal space in treatment of bulky vaginal stump recurrence of uterine cancer

International Nuclear Information System (INIS)

Kishi, Kazushi; Mabuchi, Yasushi; Sonomura, Tetsuo; Shirai, Shintaro; Noda, Yasutaka; Sato, Morio; Ino, Kazuhiko

2012-01-01

The purpose of this study is to develop a procedure for eradicative brachytherapy that can deliver a curative boost dose to bulky (>4 cm) vaginal stump recurrence of uterine cancer without risk of damaging surrounding organs. We separated risk organs (the rectum and sigmoid) from the target during brachytherapy, with a hyaluronate gel injection into the pararectal space via the percutaneous paraperineal approach under local anesthesia. The rectum anchored to the sacrum by native ligament was expected to shift posteriorly. We encountered a patient with bulky stump recurrence of uterine cancer, approximately 8 cm in maximum diameter. She was complaining of abdominal pain and constipation due to bowel encasement. Following 50 Gy of external beam radiotherapy, we applied a single fraction of brachytherapy under gel separation and delivered 14.5 Gy (50.8 GyE: equivalent dose in 2-Gy fraction calculated with linear quadratic model at α/β=3) to the target. The gel injection procedure was completed in 30 min without complications. A total irradiation dose of 100.8 GyE was delivered to the target and the cumulative minimum dose to the most irradiated rectosigmoidal volume of 2 cc (cumulative D 2cc ) was calculated as 58.5 GyE with gel injection, and was estimated to be 96 GyE without. Over three years, the local stump tumor has completely disappeared, with no complications. Brachytherapy with a pararectal gel injection can be a safe and effective eradicative option for bulky vaginal stump recurrence. (author)

Predicting stump sprouting and competitive success of five oak species in southern Indiana

Science.gov (United States)

Dale R. Weigel; Chao-Ying Joanne Peng

2002-01-01

We measured 2188 oak trees (Quercus spp.) on the Hoosier National Forest in southern Indiana before and 1, 5, and 10 years after clear-cutting to determine the influence of parent tree age, diameter breast height, and site index on the probability that there was one or more living sprouts per stump: (i) 1 year after clear-cutting (sprouting...

Reverse Anterolateral Thigh Flap to Revise a Below-knee Amputation Stump at the Mid-tibial Level

Directory of Open Access Journals (Sweden)

Parviz Lionel Sadigh, MB ChB

2013-12-01

Full Text Available Summary: The reconstruction of defects around the knee often poses a challenge due to the limited availability of local soft tissues. Indeed, this same problem is encountered when attempting to revise a below-knee amputation stump. Moreover, due to a paucity of recipient vessels in those who have undergone previous amputation secondary to trauma, free-flap reconstruction is often challenging and not always successful. We report a case of a reverse anterolateral thigh (ALT flap used to revise a long below-knee amputation stump. Previous reports in the literature attest to the versatility of the reverse ALT to cover defects around the knee and proximal tibia, but to our knowledge, this is the first report of a reverse ALT reaching to the mid-tibial level.

Some regularities in invertebrate succession in different microhabitats on pine stumps

OpenAIRE

Franch, Joan

1989-01-01

Sixty eight pine stumps felled on known dates from one to sixteen years before the moment of sampling have been studied in the San Juan de la Peña woodland (province of Huesca). Four microhabitats were distinguished: bark, subcortical space, sapwood and heartwood. The object of the study is to compare the invertebrate macrofauna succession of the different microhabitats in order to find regularities among them. The biocenosis has not been completely studied: ipidae, diptera and annelidae are ...

49 CFR 372.115 - Commodities that are not exempt under 49 U.S.C. 13506(a)(6).

Science.gov (United States)

2010-10-01

..., slaughtered Charcoal Cheese Coal Cocoa beans Coffee, beans, roasted, or instant Copra meal Cotton yarn... Flaxseed meal Flour Forest products: Resin products, such as turpentine Fruits and Berries: Bananas, fresh... extracted from grain Popcorn, popped Rice, precooked Wheat germ Gravel Hair, hog or other animal, product of...

Condensate-polisher resin-leakage quantification and resin-transport studies

International Nuclear Information System (INIS)

Stauffer, C.C.; Doss, P.L.

1983-04-01

The objectives of this program were to: (1) determine the extent of resin leakage from current generation condensate polisher systems, both deep bed and powdered resin design, during cut-in, steady-state and flow transient operation, (2) analyze moisture separator drains and other secondary system samples for resin fragments and (3) document the level of organics in the secondary system. Resin leakage samples were obtained from nine-power stations that have either recirculating steam generators or once through steam generators. Secondary system samples were obtained from steam generator feedwater, recirculating steam generator blowdown and moisture separator drains. Analysis included ultraviolet light examination, SEM/EDX, resin quantification and infrared analysis. Data obtained from the various plants were compared and factors affecting resin leakage were summarized

A Comparative Uptake Study of Multiplexed PET Tracers in Mice with Turpentine-Induced Inflammation

Directory of Open Access Journals (Sweden)

Tingting Huang

2012-11-01

Full Text Available The potential value of multiplexed positron emission tomography (PET tracers in mice with turpentine-induced inflammation was evaluated and compared with 2-[18F]fluoro-2-deoxy-D-glucose ([18F]FDG for glucose metabolism imaging. These PET tracers included [18F]fluoromethylcholine ([18F]FCH for choline metabolism imaging, (S-[11C]methyl-D-cysteine ([11C]DMCYS for amino acid metabolism imaging, [11C]bis(zinc(II-dipicolylamine ([11C]DPA-Zn2+ for apoptosis imaging, 2-(4-N-[11C]-methylaminophenyl-6-hydroxybenzothiazole ([11C]PIB for β amyloid binding imaging, and [18F]fluoride (18F− for bone metabolism imaging. In mice with turpentine-induced inflammation mice, the biodistribution of all the tracers mentioned above at 5, 15, 30, 45, and 60 min postinjection was determined. Also, the time-course curves of the tracer uptake ratios for inflammatory thigh muscle (IM to normal uninflammatory thigh muscle (NM, IM to blood (BL, IM to brain (BR, and IM to liver (LI were acquired, respectively. Moreover, PET imaging with the tracers within 60 min postinjection on a clinical PET/CT scanner was also conducted. [18F]FDG and 18F− showed relatively higher uptake ratios for IM to NM, IM to BL, IM to BR, and IM to LI than [18F]FCH, [11C]DPA-Zn2+, [11C]DMCYS and [11C]PIB, which were highly consistent with the results delineated in PET images. The results demonstrate that 18F− seems to be a potential PET tracer for inflammation imaging. [18F]FCH and [11C]DMCYS, with lower accumulation in inflammatory tissue than [18F]FDG, are not good PET tracers for inflammation imaging. As a promising inflammatory tracer, the chemical structure of [11C]DPA-Zn2+ needs to be further optimized.

Comparison and Efficacy of LigaSure and Rubber Band Ligature in Closing the Inflamed Cecal Stump in a Rat Model of Acute Appendicitis

Directory of Open Access Journals (Sweden)

Chun-Chieh Yeh

2015-01-01

Full Text Available Safety of either LigaSure or rubber band in closing inflamed appendiceal stump in acute appendicitis has been less investigated. In this study, cecal ligation followed by resecting inflamed cecum was performed to mimic appendectomy in a rat model of acute appendicitis. Rats were sacrificed immediately (Group A and 7 days (Group B after cecal resection, respectively. The cecal stumps were closed by silk ligature (S, 5 mm LigaSure (L, or rubber band (R. Seven days after cecal resection, the LigaSure (BL and silk subgroups (BS had significantly less intra-abdominal adhesion and better laparotomy wound healing than rubber band subgroup (BR. The initial bursting pressure at cecal stump was comparable among the three methods; along with tissue healing process, both BL and BS provided a higher bursting pressure than BR 7 days after appendectomy. BL subgroup had more abundant hydroxyproline deposition than BS and BR subgroup. Furthermore, serum TNF-α in BR group kept persistently increasing along with time after cecal resection. Thus, the finding that LigaSure but not rubber band is safe in sealing off the inflamed cecal stump in rat model of acute appendicitis suggests the possibility of applying LigaSure for appendectomy via single port procedure or natural orifice transluminal endoscopic surgery (NOTES.

Characterization of sulfur deposition over the period of industrialization in Japan using sulfur isotope ratio in Japanese cedar tree rings taken from stumps.

Science.gov (United States)

Ishida, Takuya; Tayasu, Ichiro; Takenaka, Chisato

2015-07-01

We characterized the sulfur deposition history over the period of industrialization in Japan based on the sulfur isotope ratio (δ(34)S) in tree rings of Japanese cedar (Cryptomeria japonica D. Don) stumps. We analyzed and compared δ(34)S values in the rings from two types of disk samples from 170-year-old stumps that had been cut 5 years earlier (older forest stand) and from 40-year-old living trees (younger forest stand) in order to confirm the validity of using stump disks for δ(34)S analysis. No differences in δ(34)S values by age were found between the sample types, indicating that stump disks can be used for δ(34)S analysis. The δ(34)S profile in tree rings was significantly correlated with anthropogenic SO2 emissions in Japan (r = -0.76, p tree rings serve as a record of anthropogenic sulfur emissions. In addition, the values did not change largely from pre-industrialization to the 1940s (+4.2 to +6.1‰). The values before the 1940s are expected to reflect the background sulfur conditions in Japan and, thus, disks containing rings formed before the 1940s contain information about the natural environmental sulfur, which is useful for biogeochemical studies.

Effects of covering highland banana stumps with soil on banana weevil Cosmopolites sordidus (Coleoptera: Curculionidae) oviposition

NARCIS (Netherlands)

Masanza, M.; Gold, C.S.; Huis, van A.; Ragama, P.E.

2005-01-01

The effect of covering post-harvest banana stumps with soil on banana weevil Cosmopolites sordidus (Germar) oviposition levels was investigated at three locations, Sendusu, Kawanda Agricultural Research Institute (KARI) and Ntungamo district of southwestern Uganda. In the first experiment

K-ras mutations in gastric stump carcinomas and in carcinomas from the non-operated stomach

NARCIS (Netherlands)

van Rees, B. P.; Musler, A.; Caspers, E.; Drillenburg, P.; Craanen, M. E.; Polkowski, W.; Chibowski, D.; Offerhaus, G. J.

1999-01-01

Partial gastrectomy is a well-established pre-malignant condition. It is postulated that in the gastric stump an accelerated neoplastic process takes place, similar to that of (intestinal type) adenocarcinoma from the non-operated stomach. K-ras codon 12 mutation is one of the most frequent

Early Rupture of an Ultralow Duodenal Stump after Extended Surgery for Gastric Cancer with Duodenal Invasion Managed by Tube Duodenostomy and Cholangiostomy

Directory of Open Access Journals (Sweden)

Konstantinos Blouhos

2013-01-01

Full Text Available When dealing with gastric cancer with duodenal invasion, gastrectomy with distal resection of the duodenum is necessary to achieve negative distal margin. However, rupture of an ultralow duodenal stump necessitates advanced surgical skills and close postoperative observation. The present study reports a case of an early duodenal stump rupture after subtotal gastrectomy with resection of the whole first part of the duodenum, complete omentectomy, bursectomy, and D2+ lymphadenectomy performed for a pT3pN2pM1 (+ number 13 lymph nodes adenocarcinoma of the antrum. Duodenal stump rupture was managed successfully by end tube duodenostomy, without omental patching, and tube cholangiostomy. Close assessment of clinical, physical, and radiological signs, output volume, and enzyme concentration of the tube duodenostomy, T-tube, and closed suction drain, which was placed near the tube duodenostomy site to drain the leak around the catheter, dictated postoperative management of the external duodenal fistula.

Bronchial stump closure with amniotic membrane in animal model

Directory of Open Access Journals (Sweden)

Gholamreza Mohajeri

2014-01-01

Full Text Available Background: Coverage of the bronchial stumps (BSs with adjacent tissues can improve healing and reduce bronchial complications in complex thoracic surgery. There is no evidence for the application of human amnion allograft for prevention of air leak from the BS. The comparison of the amniotic membrane (AM and pleural patch for BS healing after lobectomy in dogs was our aim in this study. Materials and Methods: A total of eight males and females 12-24-month-old dogs between 17 and 22 kg body-weight were used in this study in 2010, Isfahan University of Medical Sciences. Animals were separated into two groups: group A (n = 4; amniotic membrane and group P (n = 4; pleural patch according to the BS closure technique performed. After lobectomy of the right middle lobe, the BS was closed, while a small bronchopleural fistula (BPF was created by inserting a catheter via edges of closed stump. Then, it was covered with a piece of AM3 × 3 cm in group A and with a pedicle graft of pleura in group P. Rethoracotomy was performed after 15 days of observation, and the BS was removed for histological examination. Histological healing was classified as complete or incomplete healing. Neoangiogenesis was measured by Von Willebrand expression using immunohistochemistry (IHC. Data were analyzed by SPSS version 15 using Fisher′s exact test, Mann-Whitney test, and T tests. Results: BPF complications were not seen during observation period. There was no significant difference in histological healing between two groups. Similarly, no significant difference was observed between the groups in terms of neoangiogenesis based on IHC examination (P value = 0.69. Conclusion: Human amnion allograft could be as effective as pleural patch for BS wrapping following pulmonary resections.

A stump-to-mill timber production cost-estimating program for cable logging eastern hardwoods

Science.gov (United States)

Chris B. LeDoux

1987-01-01

ECOST utilizes data from stand inventory, cruise data, and the logging plan for the tract in question. The program produces detailed stump-to-mill cost estimates for specific proposed timber sales. These estimates are then utilized, in combination with specific landowner objectives, to assess the economic feasibility of cable logging a given area. The program output is...

Characteristics of resin floc dispersion of anion and cation exchange resin in precoat filter using powdered ion exchange resin

Energy Technology Data Exchange (ETDEWEB)

Adachi, Tetsurou (Nitto Denko Corp., Ibaraki, Osaka (Japan)); Sawa, Toshio; Shindoh, Toshikazu

1989-09-01

The filtration performance of mixed filter aid consisting of powdered anion and cation exchange resins used in the precoat filter is closely related to the characteristics of resin floc dispersion. The factors related to resin floc dispersion of anion and cation exchange resin were investigated by measuring the specific settle volume of resin floc as an evaluating index in addition to the measurement of physical, chemical and electrochemical properties of powdered ion exchange resin. The effect of adsorption of iron oxide and polymer electrolyte and of ion exchange were determined. In addition, considered floc dispersion with adsorbing iron oxide, it was assumed that the amount and filling ratio of resin floc were related to summation and multiplication of surface electric charge respectively. An experimental expression was obtained for simulation of the change of specific settle volume of resin floc by particle size, surface area, ion exchange capacity and degree of ionization of the powdered ion exchange resin. (author).

Characteristics of resin floc dispersion of anion and cation exchange resin in precoat filter using powdered ion exchange resin

International Nuclear Information System (INIS)

Adachi, Tetsurou; Sawa, Toshio; Shindoh, Toshikazu.

1989-01-01

The filtration performance of mixed filter aid consisting of powdered anion and cation exchange resins used in the precoat filter is closely related to the characteristics of resin floc dispersion. The factors related to resin floc dispersion of anion and cation exchange resin were investigated by measuring the specific settle volume of resin floc as an evaluating index in addition to the measurement of physical, chemical and electrochemical properties of powdered ion exchange resin. The effect of adsorption of iron oxide and polymer electrolyte and of ion exchange were determined. In addition, considered floc dispersion with adsorbing iron oxide, it was assumed that the amount and filling ratio of resin floc were related to summation and multiplication of surface electric charge respectively. An experimental expression was obtained for simulation of the change of specific settle volume of resin floc by particle size, surface area, ion exchange capacity and degree of ionization of the powdered ion exchange resin. (author)

Morphology of resin-dentin interfaces after Er,Cr:YSGG laser and acid etching preparation and application of different bonding systems.

Science.gov (United States)

Beer, Franziska; Buchmair, Alfred; Körpert, Wolfram; Marvastian, Leila; Wernisch, Johann; Moritz, Andreas

2012-07-01

The goal of this study was to show the modifications in the ultrastructure of the dentin surface morphology following different surface treatments. The stability of the adhesive compound with dentin after laser preparation compared with conventional preparation using different bonding agents was evaluated. An Er,Cr:YSGG laser and 36% phosphoric acid in combination with various bonding systems were used. A total of 100 caries-free human third molars were used in this study. Immediately after surgical removal teeth were cut using a band saw and 1-mm thick dentin slices were created starting at a distance of 4 mm from the cusp plane to ensure complete removal of the enamel. The discs were polished with silicon carbide paper into rectangular shapes to a size of 6 × 4 mm (±0,2 mm).The discs as well as the remaining teeth stumps were stored in 0.9% NaCl at room temperature. The specimens were divided into three main groups (group I laser group, group II etch group, group III laser and etch group) and each group was subdivided into three subgroups which were allocated to the different bonding systems (subgroup A Excite, subgroup B Scotchbond, subgroup C Syntac). Each disc and the corresponding tooth stump were treated in the same way. After preparation the bonding composite material was applied according to the manufacturers' guidelines in a hollow tube of 2 mm diameter to the disc as well as to the corresponding tooth stump. Shear bond strength testing and environmental scanning electron microscopy were used to assess the morphology and stability of the resin-dentin interface. The self-etching bonding system showed the highest and the most constant shear values in all three main groups, thus enabling etching with phosphoric acid after laser preparation to be avoided. Thus we conclude that laser preparation creates a surface texture that allows prediction of the quality of the restoration without the risk of negative influences during the following treatment steps. This

Resin Viscosity Influence on Fiber Compaction in Tapered Resin Injection Pultrusion Manufacturing

Science.gov (United States)

Masuram, N. B.; Roux, J. A.; Jeswani, A. L.

2018-06-01

Viscosity of the liquid resin effects the chemical and mechanical properties of the pultruded composite. In resin injection pultrusion manufacturing the liquid resin is injected into a specially designed tapered injection chamber through the injection slots present on top and bottom of the chamber. The resin is injected at a pressure so as to completely wetout the fiber reinforcements inside the tapered injection chamber. As the resin penetrates through the fibers, the resin also pushes the fibers away from the wall towards the center of chamber causing compaction of the fiber reinforcements. The fibers are squeezed together due to compaction, making resin penetration more difficult; thus higher resin injection pressures are required to efficaciously penetrate through the compacted fibers and achieve complete wetout. The impact of resin viscosity on resin flow, fiber compaction, wetout and on the final product is further discussed. Injection chamber design predominantly effects the resin flow inside the chamber and the minimum injection pressure required to completely wet the fibers. Therefore, a desirable injection chamber design is such that wetout occurs at lower injection pressures and at low internal pressures inside the injection chamber.

Effects of blood contamination on resin-resin bond strength.

Science.gov (United States)

Eiriksson, Sigurdur O; Pereira, Patricia N R; Swift, Edward J; Heymann, Harald O; Sigurdsson, Asgeir

2004-02-01

Incremental placement and curing of resin composites has been recommended. However, this requires longer operating time, and therefore, increased risk of contamination. The purpose of this study was to evaluate the effects of blood contamination on microtensile bond strengths (microTBS) between resin interfaces and to determine the best decontamination method to re-establish the original resin-resin bond strength. The top surfaces of 64, 4-mm composite blocks (Z-250, Renew, APX, Pertac II) were untreated as the control, or were treated as follows: blood applied and dried on the surface (Treatment 1), blood applied, rinsed, dried (Treatment 2), blood applied, rinsed, and an adhesive applied (Single Bond, One-Step, Clearfil SE, Prompt L-Pop) (Treatment 3). Fresh composite was applied and light-cured in 2-mm increments. After 24 h storage in water, the specimens were sectioned into 0.7-mm thick slabs, trimmed to a cross-sectional area of 1 mm(2), and loaded to failure at a crosshead speed of 1 mm/min using an Instron universal testing machine. Data were analyzed using two-way ANOVA and Fisher's PLSD test (pcontamination resulted in resin-resin bond strengths of only 1.0-13.1 MPa. Rinsing raised bond strengths to over 40 MPa for each material. Use of an adhesive further increased bond strengths except for Pertac II. Rinsing blood from contaminated surfaces increases the resin-resin bond strength significantly and the application of an appropriate adhesive increases the bond strength to control levels.

Foam, Foam-resin composite and method of making a foam-resin composite

Science.gov (United States)

Cranston, John A. (Inventor); MacArthur, Doug E. (Inventor)

1995-01-01

This invention relates to a foam, a foam-resin composite and a method of making foam-resin composites. The foam set forth in this invention comprises a urethane modified polyisocyanurate derived from an aromatic amino polyol and a polyether polyol. In addition to the polyisocyanurate foam, the composite of this invention further contains a resin layer, wherein the resin may be epoxy, bismaleimide, or phenolic resin. Such resins generally require cure or post-cure temperatures of at least 350.degree. F.

Single-tree harvesting reduces survival and growth of oak stump sprouts in the Missouri Ozark Highlands

Science.gov (United States)

Daniel C. Dey; Randy G. Jensen; Michael J. Wallendorf

2008-01-01

Regeneration and recruitment into the overstory is critical to the success of using uneven-aged systems to sustain oak forests. We evaluated survival and growth of white oak (Quercus alba L.), black oak (Q. velutina Lam.), and scarlet oak (Q. coccinea Muenchh.) stump sprouts 10 years after harvesting Ozark...

[Vacuum sealing drainage combined with free skin graft in repairing cutaneous deficiency of traumatic shank amputation stump].

Science.gov (United States)

Zhao, Xiao-fei; Li, Chun-you; Jin, Guo-qiang; Ming, Xiao-feng; Wang, Guo-jie

2014-12-01

To observe clinical efficacy in treating cutaneous deficiency of traumatic shank amputation stump with full-thickness skin graft combined with vacuum sealing drainage. From September 2009 to December 2012, 15 patients with cutaneous deficiency of traumatic shank amputation stump were treated with full-thickness skin graft combined with vacuum sealing drainage. Among patients, there were 11 males and 4 females with an average age of 41.5 (ranged from 25 to 62) years old. Ten cases were caused by traffic accident and 5 cases were caused by heavy object, 9 cases on left and 6 cases on right. Six patients with smashed wound were treated with debridement and amputation, combined with vacuum aspiration in-emergency; 9 patients caused by infection and necrosis were treated with debridement and amputation, combined with vacuum aspiration, and full-thickness skin graft were performed at stage II. The skin defect area of residual limbs ranged from 40 cm x 20 cm to 25 cm x 15 cm. All patients were followed up from 3 months to 1 year. Full-thickness skin graft of residual limbs were survived,and obtained satisfactory walking function with prosthetic. Residual skin increased thicken, wearproof without rupture and pain. Full-thickness skin graft combined with vacuum sealing drainage in treating cutaneous deficiency of traumatic shank amputation stump could reserve the length of residual limbs, increase survival rate of skin graft with less scar of survival skin, get good wearability and it is conducive to prosthetic wear. It is a simple and easy treatment method.

Pancreatic stump closure using only stapler is associated with high postoperative fistula rate after minimal invasive surgery.

Science.gov (United States)

Yüksel, Adem; Bostancı, Erdal Birol; Çolakoğlu, Muhammet Kadri; Ulaş, Murat; Özer, İlter; Karaman, Kerem; Akoğlu, Musa

2018-03-01

Postoperative pancreatic fistula (POPF) is the most common cause of morbidity and mortality after distal pancreatectomy (DP). The aim of the present study is to determine the risk factors that can lead to POPF. The study was conducted between January 2008 and December 2012. A total of 96 patients who underwent DP were retrospectively analyzed. Overall, 24 patients (25%) underwent laparoscopic distal pancreatectomy (LDP) and 72 patients (75%) open surgery. The overall morbidity rate was 51% (49/96). POPF (32/96, 33.3%) was the most common postoperative complication. Grade B fistula (18/32, 56.2%) was the most common fistula type according to the International Study Group on Pancreatic Fistula definition. POPF rate was significantly higher in the minimally invasive surgery group (50%, p=0.046). POPF rate was 58.6% (17/29) in patients whose pancreatic stump closure was performed with only stapler, whereas POPF rate was 3.6% (1/28) in the group where the stump was closed with stapler plus oversewing sutures. Both minimally invasive surgery (OR: 0.286, 95% CI: 0.106-0.776, p=0.014) and intraoperative blood transfusion (OR: 4.210, 95% CI: 1.155-15.354, p=0.029) were detected as independent risk factors for POPF in multi-variety analysis. LDP is associated with a higher risk of POPF when stump closure is performed with only staplers. Intraoperative blood transfusion is another risk factor for POPF. On the other hand, oversewing sutures to the stapler line reduces the risk of POPF.

Variation in Results of Volume Measurements of Stumps of Lower-Limb Amputees : A Comparison of 4 Methods

NARCIS (Netherlands)

de Boer-Wilzing, Vera G.; Bolt, Arjen; Geertzen, Jan H.; Emmelot, Cornelis H.; Baars, Erwin C.; Dijkstra, Pieter U.

de Boer-Wilzing VG, Bolt A, Geertzen JH, Emmelot CH, Baars EC, Dijkstra PU. Variation in results of volume measurements of stumps of lower-limb amputees: a comparison of 4 methods. Arch Phys Med Rehabil 2011;92:941-6. Objective: To analyze the reliability of 4 methods (water immersion,

[Stump forming after traumatic foot amputation of a child--description of a new surgical procedure and literature review of lawnmower accidents].

Science.gov (United States)

Bayer, J; Zajonc, H; Strohm, P C; Vohrer, M; Maier-Lenz, D; Südkamp, N P; Schwering, L

2009-01-01

Amputation injuries in children occur in motor vehicle, farming and, importantly, lawn mower accidents. Treatment of lawn mower related injuries is complicated by gross wound contamination, avascular tissue, soft tissue defects and exposed bone. Many treatment options exist and often an adequate prosthetic supply is needed for rehabilitation. We report on an 8-year old boy who got under a ride-on lawn mower and sustained a subtotal amputation of his right foot. After initial surgery an amputation was subsequently necessary. For this, it had to be taken into account that the traumatic loss of the talus, calcaneus and parts of the cuboid bone would result in a length shortening of the right leg and so far not injured metatarsal and tarsal bones had to be sacrificed. Thus, we aimed to develop a new operation technique to optimize stump length as well as preserve tarsal bones and the possibility of limb growth. In order to achieve this, we performed a new stump forming operation in which we integrated uninjured tarsal and metatarsal bones. First a Lisfranc's amputation was performed and a metatarsal bone was kept aside. The talus, calcaneus as well as the cuboid bone were either completely or almost completely destroyed and were removed. The remaining cuneiform bones were transfixed by a notched metatarsal bone, thus achieving a tarsal arthrodesis, and the cartilages of the proximal joint surfaces were removed. The cartilage of the cranial and caudal navicular as well as the distal tibial joint surface was also removed and an arthrodesis between the distal tibia and the navicular bone was achieved by crossed Kirschner wires. Finally the cuneiform bones were placed inferior to the navicular bone. Further stump coverage was managed by skin and muscle flaps as well as split skin graft. Our patient was discharged on day 34. A fluent gait without crutches as well as sports activities were possible again as early as 6 1/2 months after the injury. Using our stump forming

Chapter 6: Prehydrolysis Pulping with Fermentation Coproducts

Science.gov (United States)

T.H. Wegner; C.J. Houtman; A.W. Rudie; B.L. Illman; P.J. Ince; E.M. Bilek; T.W. Jeffries

2013-01-01

Although the term “integrateed biorefinery” is new, the concept has long been familiar to the pulp and paper industry, where processes include biomass boilers providing combined heat and power, and byproducts of pulping include turpentine, fatty acids and resin acids. In the dominant kraft (or sulfate) pulping process, dissolved lignin and chemicals from the pulp...

Fungal Transformation of Tree Stumps into a Suitable Resource for Xylophagous Beetles via Changes in Elemental Ratios

Directory of Open Access Journals (Sweden)

Michał Filipiak

2016-04-01

Full Text Available The elements present in dead pine stumps inhabited by larvae of wood-boring beetles (Stictoleptura rubra, Arhopalus rusticus and Chalcophora mariana were analyzed over the initial (first 5 years; a chronosequence stages of wood decay. The quantities of N, P, K, Ca, Mg, Fe, Zn, Mn, Cu and Na (but not S increased with increases in the content of ergosterol (used as a proxy for the amount of fungal tissue. In fact, the amounts of P, N, K, Fe and Cu presented marked increases. These findings show that fungi stoichiometrically rearrange dead wood by importing externally occurring nutrients to decaying stumps. During the first years of wood decay, the ratios of C to other elements decrease substantially, but differently, for various elements, whereas the N:Fe, N:Cu, N:P and N:K ratios remain relatively stable. Therefore, the stoichiometric mismatch between xylophages and their food is greatly reduced. By changing the nutritional stoichiometry of dead wood, fungi create a nutritional niche for wood-eaters, and these changes enable the development of xylophages.

Fungal Transformation of Tree Stumps into a Suitable Resource for Xylophagous Beetles via Changes in Elemental Ratios

Science.gov (United States)

Filipiak, Michał; Sobczyk, Łukasz; Weiner, January

2016-01-01

The elements present in dead pine stumps inhabited by larvae of wood-boring beetles (Stictoleptura rubra, Arhopalus rusticus and Chalcophora mariana) were analyzed over the initial (first 5 years; a chronosequence) stages of wood decay. The quantities of N, P, K, Ca, Mg, Fe, Zn, Mn, Cu and Na (but not S) increased with increases in the content of ergosterol (used as a proxy for the amount of fungal tissue). In fact, the amounts of P, N, K, Fe and Cu presented marked increases. These findings show that fungi stoichiometrically rearrange dead wood by importing externally occurring nutrients to decaying stumps. During the first years of wood decay, the ratios of C to other elements decrease substantially, but differently, for various elements, whereas the N:Fe, N:Cu, N:P and N:K ratios remain relatively stable. Therefore, the stoichiometric mismatch between xylophages and their food is greatly reduced. By changing the nutritional stoichiometry of dead wood, fungi create a nutritional niche for wood-eaters, and these changes enable the development of xylophages.

Comparison of extra-corporeal knot-tying suture and metallic endo-clips in laparoscopic appendiceal stump closure in uncomplicated acute appendicitis

Directory of Open Access Journals (Sweden)

M. Nadeem

2016-01-01

Conclusion: The use of metallic endoclip for appendix stump closure is safe and less time consuming but costs higher. Because of the simplicity of the technique it's a useful alternative to the extracorporeal knotting especially for learners.

Investigating the mechanism underlying urinary continence recovery after radical prostatectomy: effectiveness of a longer urethral stump to prevent urinary incontinence.

Science.gov (United States)

Kadono, Yoshifumi; Nohara, Takahiro; Kawaguchi, Shohei; Naito, Renato; Urata, Satoko; Nakashima, Kazufumi; Iijima, Masashi; Shigehara, Kazuyoshi; Izumi, Kouji; Gabata, Toshifumi; Mizokami, Atsushi

2018-02-28

To assess the chronological changes in urinary incontinence and urethral function before and after radical prostatectomy (RP), and to compare the findings of pelvic magnetic resonance imaging (MRI) before and after RP to evaluate the anatomical changes. In total, 185 patients were evaluated with regard to the position of the distal end of the membranous urethra (DMU) on a mid-sagittal MRI slice and urethral sphincter function using the urethral pressure profilometry. The patients also underwent an abdominal leak point pressure test before RP and at 10 days and 12 months after RP. The results were then compared with the chronological changes in urinary incontinence. The MRI results showed that the DMU shifted proximally to an average distance of 4 mm at 10 days after RP and returned to the preoperative position at 12 months after RP. Urethral sphincter function also worsened 10 days after RP, with recovery after 12 months. The residual length of the urethral stump and urinary incontinence were significantly associated with the migration length of the DMU at 10 days after RP. The residual length of the urethral stump was a significant predictor of urinary incontinence after RP. This is the first study to elucidate that the slight vertical repositioning of the membranous urethra after RP causes chronological changes in urinary incontinence. A long urethral residual stump reduces urinary incontinence after RP. © 2018 The Authors BJU International © 2018 BJU International Published by John Wiley & Sons Ltd.

Modern principles of prevention of anophthalmic syndrome: formation of the locomotor stump, the types of orbital implants

Directory of Open Access Journals (Sweden)

I. V. Zapuskalov

2017-01-01

Full Text Available This article analyzes the current state of the problem of the correction of anophthalmic syndrome. Evaluated various methods of formation of the locomotor stump after removal of the eyeball, gave a detailed description of different types of materials for the fabrication of orbital implant, as well as reflect the basic principles of prevention of complications.

Correlations of norbornenyl crosslinked polyimide resin structures with resin thermo-oxidative stability, resin glass transition temperature and composite initial mechanical properties

Science.gov (United States)

Alston, William B.

1988-01-01

PMR (polymerization of monomeric reactants) methodology was used to prepare 70 different polyimide oligomeric resins and 30 different unidirectional graphite fiber/polyimide composites. Monomeric composition as well as chain length between sites of crosslinks were varied to examine their effects on resin thermo-oxidative stability and glass transition temperature (Tg) of the cured/postcured resins. A linear correlation of decreasing 316 C resin weight loss/surface area versus (1) decreasing aliphatic content, or (2) increasing benzylic/aliphatic content stoichiometry ratio over a wide range of resin compositions was observed. An almost linear correlation of Tg versus molecular distance between the crosslinks was also observed. An attempt was made to correlate Tg with initial composite mechanical properties (flexural strength and interlaminar shear strength). However, the scatter in mechanical strength data prevented obtaining a clear correlation. Instead, only a range of composite mechanical properties was obtained at 25, 288, and 316 C. Perhaps more importantly, what did become apparent during the correlation study was (1) the PMR methodology could be used to prepare composites from resins containing a wide variety of monomer modifications, (2) that these composites almost invariably provided satisfactory initial mechanical properties as long as the resins formulated exhibited satisfactory processing flow, and (3) that PMR resins exhibited predictable rates of 316 C weight loss/surface area based on their benzylic/aliphatic stoichiometery ratio.

Polyvinyl chloride resin

International Nuclear Information System (INIS)

Kim, Hong Jae

1976-06-01

This book contains polyvinyl chloride resin industry with present condition such as plastic industry and polyvinyl chloride in the world and Japan, manufacture of polyvinyl chloride resin ; suspension polymerization and solution polymerization, extruding, injection process, hollow molding vinyl record, vacuum forming, polymer powders process, vinyl chloride varnish, vinyl chloride latex, safety and construction on vinyl chloride. Each chapter has descriptions on of process and kinds of polyvinyl chloride resin.

Borax Stump Treatment for Control of Annosus Root Disease in the Eastside Pine Type Forests of Northeastern California

Science.gov (United States)

John T. Kliejunas

1989-01-01

A historical perspective and description of recent studies on the use of borax to treat pine stumps against infection by Heterobasidion annosum in eastside pine stands of northeastern California are presented. The studies indicate that boraxing of pines in eastside pine stands is an effective means of preventing annosus infection. Data and...

EPICOR-II resin degradation results from first resin samples of PF-8 and PF-20

International Nuclear Information System (INIS)

McConnell, J.W. Jr.; Sanders, R.D. Sr.

1985-12-01

The 28 March 1979 accident at Three Mile Island Unit 2 released approximately 560,000 gallons of contaminated water to the Auxiliary and Fuel Handling Buildings. The water was decontaminated using a demineralization system called EPICOR-II developed by Epicor, Inc. The Low-Level Waste Data Base Development - EPICOR-II Resin/Liner Investigation Project is studying the chemical and physical conditions of the synthetic ion exchange resins found in several EPICOR-II prefilters. This report summarizes results and analyses of the first sampling of ion exchange resins from EPICOR-II prefilters PE-8 and -20. Results are compared with baseline data from tests performed on unirradiated Epicor, Inc. resins to determine if degradation has occurred due to the high internal radiation dose received by the EPICOR-II resins. Results also are compared with recent findings on resin degradation by Battelle Columbus Laboratories and Brookhaven National Laboratory. Analyses comparing test results of resins from EPICOR-II prefilters PF-8 and -20 with unirradiated resins obtained from Epicor, Inc. show resin degradation has occurred in some of the EPICOR-II resins examined. The mechanism of degradation is compared with work of other researchers and is consistent with their findings. The strong acid cation resins (divinylbenzene, styrene base structure) are losing effective cross-linking along with scission of functional groups and are experiencing first an increase and eventually a decrease in total exchange capacity as the absorbed radiation dose increases. The phenolic cation resins (phenol-formaldehyde base structure) show a loss of effective cross-linking and oxidation of the polymer chain. Analyses of resins removed from EPICOR-II prefilters PF-8 and -20 over the next several years should show a further increase in degradation

Post-irradiation hardness of resin-modified glass ionomer cements and a polyacid-modified composite resin

International Nuclear Information System (INIS)

Yap, A.U.J.

1997-01-01

This study examined the post-irradiation hardness of resin-modified glass ionomer cements and a polyacid-modified composite resin using a digital microhardness tester. Change in hardness of these materials over a period of 6 months was compared to that of conventional glass ionomer cements and a composite resin. With the exception of the composite resin, all materials showed a significant increase in hardness over 24 h after their initial set. Dual-cure resin-modified glass ionomer cements showed decreased hardness with increased storage time in saline at 37 o C. Results suggest that the addition of resins to glass ionomer cements does not improve initial hardness and does not negate the acid-base reaction of conventional cements. Resin addition may, however, lead to increased water sorption and decreased hardness. (author)

Thermal cycling effects on adhesion of resin-bovine enamel junction among different composite resins.

Science.gov (United States)

Chen, Wen-Cheng; Ko, Chia-Ling; Wu, Hui-Yu; Lai, Pei-Ling; Shih, Chi-Jen

2014-10-01

Thermal cycling is used to mimic the changes in oral cavity temperature experienced by composite resins when used clinically. The purpose of this study is to assess the thermal cycling effects of in-house produced composite resin on bonding strength. The dicalcium phosphate anhydrous filler surfaces are modified using nanocrystals and silanization (w/NP/Si). The resin is compared with commercially available composite resins Filtek Z250, Z350, and glass ionomer restorative material GIC Fuji-II LC (control). Different composite resins were filled into the dental enamel of bovine teeth. The bond force and resin-enamel junction graphical structures of the samples were determined after thermal cycling between 5 and 55°C in deionized water for 600 cycles. After thermal cycling, the w/NP/Si 30wt%, 50wt% and Filtek Z250, Z350 groups showed higher shear forces than glass ionomer GIC, and w/NP/Si 50wt% had the highest shear force. Through SEM observations, more of the fillings with w/NP/Si 30wt% and w/NP/Si 50wt% groups flowed into the enamel tubule, forming closed tubules with the composite resins. The push-out force is proportional to the resin flow depth and uniformity. The push-out tubule pore and resin shear pattern is the most uniform and consistent in the w/NP/Si 50wt% group. Accordingly, this developed composite resin maintains great mechanical properties after thermal cycling. Thus, it has the potential to be used in a clinical setting when restoring non-carious cervical lesions. Copyright © 2014 Elsevier Ltd. All rights reserved.

Resin composites

DEFF Research Database (Denmark)

Benetti, Ana Raquel; Peutzfeldt, Anne; Lussi, Adrian

2014-01-01

OBJECTIVE: To investigate how the modulus of elasticity of resin composites influences marginal quality in restorations submitted to thermocyclic and mechanical loading. METHODS: Charisma, Filtek Supreme XTE and Grandio were selected as they were found to possess different moduli of elasticity...... of resin composite (p=0.81) on the quality of dentine margins was observed, before or after loading. Deterioration of all margins was evident after loading (p....008). CONCLUSIONS: The resin composite with the highest modulus of elasticity resulted in the highest number of gap-free enamel margins but with an increased incidence of paramarginal enamel fractures. CLINICAL SIGNIFICANCE: The results from this study suggest that the marginal quality of restorations can...

Comparison of Mechanical Properties of Resin Composites with Resin Modified Glass Ionomers

Directory of Open Access Journals (Sweden)

Taha NA

2015-06-01

Full Text Available Statement of Problem: There are controversial reports regarding physical and mechanical properties of resin composites and glass ionomer cements. Some revealed higher strength and hardness for resin composites while others showed a comparable value for glass ionomer cements. Evaluation of mechanical properties of different types of resin composites in comparison with resin modified glass ionomers is not widely studied. Objectives: To measure and compare the flexural strength and Vickers hardness of three resin composites and two resins modified glass ionomer cements before and after ageing. Materials and Methods: Three resin composites, i.e. Filtek Supreme XTE (3M ESPE, Ice (SDI, Gradia (GC, and two resins modified glass ionomers, i.e. Fuji II LC (GC and Riva Light Cure (SDI, were selected. Ten barshaped specimens were prepared for each material and cured using LED curing light. After 24 hours storage in distilled water at 37oC, the specimens were randomly divided into two equal groups (n=5. The first group was tested as a baseline and the second group was restored at 37oC for another 29 days. Flexural strength was performed by four-point bending test using universal testing machine at crosshead speed of 0.5mm/min, and the maximum load at failure was recorded. The specimen’s halves were used for evaluating Vickers hardness, using a Digital Hardness Tester (300 g/15 sec and the Vickers hardness number (VHN was recorded. Data were analyzed using one-way analysis of variance (ANOVA, Tukey’s and student’s t-test. Results: After 24 hours of immersion, the highest hardness number was found for Filtek Supreme and Ice and the highest flexural strength was obtained for Gradia. After 30 days of storage, hardness of Fuji II LC and Gradia showed a significant decrease; flexural strength of Ice and Fuji II LC revealed a significant increase while Gradia and Filtek Supreme showed a significant decrease. Conclusions: Resin modified glass ionomers showed

On the appearance of acetylcholine receptors in denervated rat diaphragm, and its dependence on nerve stump length

International Nuclear Information System (INIS)

Uchitel, O.; Robbins, N.

1978-01-01

Acetylcholine (ACh) sensitivity and extrajunctional receptor distribution of the rat diaphragm were closely monitored during the early period following denervation. Both contracture in response to 10 μg/ml of ACh and extrajunctional binding of [ 125 I]alpha-bungarotoxin ([ 125 I]α-BTX) were first detectable 30 h after cutting the phrenic nerve in the thorax. If the nerve were cut more proximally, leaving a 3.5 cm distal nerve stump, the same level of ACh contracture and [ 125 I]α-BTX binding did not appear until 40 h after operation. This 10-h delay was far longer than the 3-h delay in transmission failure reportedly dependent on stump length. The earliest detectable extrajunctional [ 125 I]α-BTX binding appeared throughout the entire muscle fiber, and was not localized to the endplate region as would be expected if degeneration in the nerve terminal induced new receptors. However, later significant increases in [ 125 I]α-BTX binding at the endplate region could have resulted from such degeneration. All these results are consistent with neurotrophic regulation of muscle ACh receptors, working via a mechanism involving axonal transport. (Auth.)

The mechanism of uranium adsorption on Resin 508 and isoelectric point of the resin

International Nuclear Information System (INIS)

Han Qingping; Lu Weichang; Su Huijuan; Hu Jinbo; Zhang Liqin; Chen Banglin

1990-01-01

The adsorption process of uranium by Resin 508 at the solid-liquid interface was investigated and the mechanism of uranium adsorption including adsorption dynamics, adsorption thermodynamics and isoelectric point of resin was studied. The results are as follows: The maximum of uranium adsorption is attained at pH5-7; Uranium adsorption isotherm by Resin 508 in experimental conditions agrees with Langmuir's adsorption isotherm, the maximum of uranium adsorbed (Vm) is 716 mg U/g-dried resin; The adsorption of uranium by Resin 508 is an endothermic reaction and ΔH = 16.87 kJ/mol; The exchange-adsorption rate is mainly controlled by liquid film diffusion; The isoelectric points of Resin 508 before and after uranium adsorption are found to be pH7.5 and pH5.7 respectively. It is a specific adsorption for uranium

Resin regenerating device in condensate desalting system

International Nuclear Information System (INIS)

Sato, Yoshiaki; Igarashi, Hiroo; Oosumi, Katsumi; Nishimura, Yusaku; Ebara, Katsuya; Shindo, Norikazu.

1984-01-01

Purpose: To improve the accuracy in the separation of anionic and cationic exchange resins. Constitution: Resins transferred from a condensate desalting column are charged in a cationic exchange resin column. The temperature of water for separating and transferring the resins is measured by a temperature detector disposed in a purified water injection line, and water is adjusted to a suitable flow rate for the separation and transfer of the resins by an automatic flow rate control valve, and then is injected. The resins are separated into cationic exchange resins and anionic exchange resins, in which only the anionic exchange resins are transferred, through an anionic exchange transfer line, into an anionic exchange resin column. By controlling the flow rate depending on the temperature of the injected water, the developing rate of the resin layer is made constant to enable separation and transfer of the resins at high accuracy. (Seki, T.)

Characteristics of floc formation of anion and cation exchange resin in precoat filter using powdered ion exchange resin

International Nuclear Information System (INIS)

Adachi, Tetsurou; Sawa, Toshio; Shindoh, Toshikazu.

1989-01-01

The filtration performance of mixed filter aid consisting of powdered anion and cation exchange resins used in the precoat filter is closely related to the characteristics of floc formation. The physical, chemical and electrochemical properties of powdered ion exchange resin were measured and the factors related to floc formation of anion and cation exchange resin were investigated by measuring the specific settle volume of resin floc as an evaluating index. It was found that these factors were mixing ratio, nature of resins and particle size of resins. In addition, it was assumed on the bases of these results that the amount of resin floc was related to sum of the surface electric charges of both resins. The filling ratio of resin floc was related to their product by multiplication and an experimental expression was obtained. The specific settle volume of resin floc could then be simulated by particle size, surface area, ion exchange capacity and degree of ionization of the powdered ion exchange resin. (author)

Characteristics of floc formation of anion and cation exchange resin in precoat filter using powdered ion exchange resin

Energy Technology Data Exchange (ETDEWEB)

Adachi, Tetsurou (Nitto Denko Corp., Ibaraki, Osaka (Japan)); Sawa, Toshio; Shindoh, Toshikazu

1989-09-01

The filtration performance of mixed filter aid consisting of powdered anion and cation exchange resins used in the precoat filter is closely related to the characteristics of floc formation. The physical, chemical and electrochemical properties of powdered ion exchange resin were measured and the factors related to floc formation of anion and cation exchange resin were investigated by measuring the specific settle volume of resin floc as an evaluating index. It was found that these factors were mixing ratio, nature of resins and particle size of resins. In addition, it was assumed on the bases of these results that the amount of resin floc was related to sum of the surface electric charges of both resins. The filling ratio of resin floc was related to their product by multiplication and an experimental expression was obtained. The specific settle volume of resin floc could then be simulated by particle size, surface area, ion exchange capacity and degree of ionization of the powdered ion exchange resin. (author).

Herbicidas e danos físicos em tocos de teca para controle de brotos após o desbaste Herbicides and physical damages in teak stumps to control of sprouts after thinning

Directory of Open Access Journals (Sweden)

Sidney Fernando Caldeira

2012-10-01

Full Text Available Tocos de árvores desbastadas de Tectona grandis apresentam rebrota intensa que compete com as árvores remanescentes. O objetivo deste trabalho foi avaliar a eficácia da aplicação isolada ou combinada de diferentes concentrações dos herbicidas picloram e triclopyr, associados ou não à aplicação de danos físicos, no controle dessas brotações. Em um povoamento com quatro anos de idade, os tocos foram tratados imediatamente após o desbaste. Em outro povoamento com seis anos, foram tratadas as brotações presentes nos tocos desbastados no ano anterior. Foi registrada a porcentagem de tocos mortos, o número de brotações por toco e as respectivas alturas. No primeiro ensaio, a aplicação combinada de picloram a 0,48% com triclopyr a 0,96%, associada a 20 rachas com machado matou todos os tocos. No segundo ensaio, a maior eficácia, 21,7%, foi registrada com roçada prévia das brotações e a aplicação de picloram a 0,96%. Após o desbaste, a aplicação isolada de picloram ou combinada com triclopyr associada ou não aos danos físicos é eficiente para controlar os brotos de teca. A aplicação nas rebrotas de tocos desbastados no ano anterior apresenta alguma eficiência, mas com menor percentual de tocos mortos em relação à aplicação após o desbaste.The stumps of thinning trees of Tectona grandis L.f. present intense sprouts that compete with the remaining trees. The efficacy of the control of sprouts with the herbicides picloram and triclopyr, associated or no it applications of physical damages, were evaluated. Immediately after thinning, in plantation with four years old, the stumps were treated, and in other plantation, with age of six, the sprouts of stumps thinned in the previous year, were treated. The percentage of died stumps, the number of sprouts by stump and the respective heights were registered. In the first trial, the combined application of picloram at 0.48% with triclopyr at 0.96%, associated a 20 cracks

EDF specifications on nuclear grade resins

International Nuclear Information System (INIS)

Mascarenhas, Darren; Gressier, Frederic; Taunier, Stephane; Le-Calvar, Marc; Ranchoux, Gilles; Marteau, Herve; Labed, Veronique

2012-09-01

Ion exchange resins are widely used across EDF, especially within the nuclear division for the purification of water. Important applications include primary circuit, secondary circuit and effluent treatment, which require high quality nuclear grade resins to retain the dissolved species, some of which may be radioactive. There is a need for more and more efficient purification in order to decrease worker dose during maintenance but also to decrease volumes of radioactive resin waste. Resin performance is subject to several forms of degradation, including physical, chemical, thermal and radioactive, therefore appropriate resin properties have to be selected to reduce such effects. Work has been done with research institutes, manufacturers and on EDF sites to select these properties, create specifications and to continuously improve on these specifications. An interesting example of research regarding resin performance is the resin degradation under irradiation. Resins used in the CVCS circuit of EDF nuclear power plants are subject to irradiation over their lifetime. A study was carried out on the effects of total integrated doses of 0.1, 1 and 10 MGy on typically used EDF mixed bed resins in a 'mini-CVCS' apparatus to simultaneously test actual primary circuit fluid. The tests confirmed that the resins still perform efficiently after a typical CVCS radiation dose. Certain resins also need additional specifications in order to maintain the integrity of the particular circuits they are used in. Recently, EDF has updated its requirements on these high purity nuclear grade resins, produced generic doctrines for all products and materials used on site which include resins of all grades, and as a result have also updated a guide on recommended resin usage for the French fleet of reactors. An overview of the evolutions will be presented. (authors)

System for removing contaminants from plastic resin

Science.gov (United States)

Bohnert, George W.; Hand, Thomas E.; DeLaurentiis, Gary M.

2010-11-23

A resin recycling system that produces essentially contaminant-free synthetic resin material in an environmentally safe and economical manner. The system includes receiving the resin in container form. A grinder grinds the containers into resin particles. The particles are exposed to a solvent in one or more solvent wash vessels, the solvent contacting the resin particles and substantially removing contaminants on the resin particles. A separator is used to separate the resin particles and the solvent. The resin particles are then placed in solvent removing element where they are exposed to a solvent removing agent which removes any residual solvent remaining on the resin particles after separation.

[Acrylic resin removable partial dentures].

Science.gov (United States)

de Baat, C; Witter, D J; Creugers, N H J

2011-01-01

An acrylic resin removable partial denture is distinguished from other types of removable partial dentures by an all-acrylic resin base which is, in principle, solely supported by the edentulous regions of the tooth arch and in the maxilla also by the hard palate. When compared to the other types of removable partial dentures, the acrylic resin removable partial denture has 3 favourable aspects: the economic aspect, its aesthetic quality and the ease with which it can be extended and adjusted. Disadvantages are an increased risk of caries developing, gingivitis, periodontal disease, denture stomatitis, alveolar bone reduction, tooth migration, triggering of the gag reflex and damage to the acrylic resin base. Present-day indications are ofa temporary or palliative nature or are motivated by economic factors. Special varieties of the acrylic resin removable partial denture are the spoon denture, the flexible denture fabricated of non-rigid acrylic resin, and the two-piece sectional denture. Furthermore, acrylic resin removable partial dentures can be supplied with clasps or reinforced by fibers or metal wires.

Properties of the Carboxylate ion exchange resins

International Nuclear Information System (INIS)

Allard, Bert; Dario, Maarten; Boren, Hans; Torstenfelt, Boerje; Puigdomenech, Ignasi; Johansson, Claes

2002-09-01

Weakly acidic, carboxylic resin has been selected, together with strong base anion resins, for water purification at the Forsmark 1 and 2 reactors. For the strong (but not the weak) ion exchange resin the Nuclear Power Inspectorate has given permission to dispose the spent resins in the SFR 1 (the Final Repository for Radioactive Operational Waste). This report gives a review of the carboxylic resins and comes to the conclusion that the resins are very stable and that there should not exist any risks for increased leaching of radionuclides from SFR 1 if these resins are disposed (compared to the strong resins)

Bond strength of resin-resin interfaces contaminated with saliva and submitted to different surface treatments

Directory of Open Access Journals (Sweden)

Adilson Yoshio Furuse

2007-12-01

Full Text Available The purpose of this study was to investigate the effect of different surface treatments on shear bond strength of saliva-contaminated resin-resin interfaces. Flat resin surfaces were fabricated. In the control group, no contamination or surface treatment was performed. The resin surfaces of the experimental groups were contaminated with saliva and air-dried, and then submitted to: (G1 rinsing with water and drying; (G2 application of an adhesive system; (G3 rinsing and drying, abrasion with finishing disks, etching and application of adhesive system; (G4 rinsing and drying, etching, application of silane and adhesive system. Resin cylinders were placed over the treated surfaces. The specimens were stored in water or ethanol. Shear bond strength tests were performed and the mode of failure was evaluated. Data were submitted to two-way ANOVA and Dunnett T3 test. Contamination of resin-resin interfaces with saliva significantly reduced shear strength, especially after prolonged storage (p<0.05. Similar values to the original bond strength were obtained after abrasion and application of adhesive (G3 or etching and application of silane and adhesive (G4. If contamination occurs, a surface treatment is required to guarantee an adequate interaction between the resin increments.

Comparative study of resin sealant and resin modified glass ionomer as pit and fissure sealant

Directory of Open Access Journals (Sweden)

Shirin Malek

2017-02-01

Full Text Available The purpose of the present study was to compare the marginal integrity of resin modified glass ionomer cement with that of resin sealant, in vitro. Forty artificial pit and fissure cavities were prepared in occlusal surface of extracted premolar teeth by using ¼ round carbide bur. Cavities were condensed with artificial organic debris followed by cleaning with prophylaxis pumice brush and paste and then separated into two treatment groups. In Group A, 15 fissure cavities were sealed by resin sealant and in Group B, 15 fissure cavities were sealed by resin modified glass ionomer sealant. These specimens were subjected to thermo-cycling followed by dye penetration test. The remaining 5 cavities from each group were analyzed for debris score by the SEM. The results of the microleakage test showed that the efficacy of preventing microleakage of samples sealed by resin modified glass ionomer sealant was higher than the samples sealed by resin sealant. However, no significant differences were found. It can be concluded that use of resin modified glass ionomer sealant is a good alternative for sealing pits and fissures.

4-META opaque resin--a new resin strongly adhesive to nickel-chromium alloy.

Science.gov (United States)

Tanaka, T; Nagata, K; Takeyama, M; Atsuta, M; Nakabayashi, N; Masuhara, E

1981-09-01

1) A new adhesive opaque resin containing a reactive monomer, 4-methacryloxy-ethyl trimellitate anhydride (4-META), was prepared, and its application to thermosetting acrylic resin veneer crowns was studied. 2) The 4-META opaque resin was applied to a variety of nickel-chromium dental alloy specimens which had undergone different treatment, and endurance tests were conducted to evaluate the durability of adhesion. 3) Stable adhesion against water penetration was achieved with metal surfaces first etched with HCl and then oxidized with HNO3. A bond strength of 250 kg/cm2 was maintained even after immersion in water at 37 degrees C for 30 wk or at 80 degrees C for ten wk. Furthermore, this value did not decrease even after the specimens were subjected to 500 thermal cycles. 4) The 4-META opaque resin studied can eliminate the necessity for retention devices on metal castings. 5) The smooth 4-META opaque resin should have no adverse effects on gingivae.

Method of solidifying radioactive ion exchange resin

International Nuclear Information System (INIS)

Minami, Yuji; Tomita, Toshihide

1989-01-01

Spent anion exchange resin formed in nuclear power plants, etc. generally catch only a portion of anions in view of the ion exchange resins capacity and most of the anions are sent while possessing activities to radioactive waste processing systems. Then, the anion exchange resins increase the specific gravity by the capture of the anions. Accordingly, anions are caused to be captured on the anion exchange resin wastes such that the specific gravity of the anion exchange resin wastes is greater than that of the thermosetting resins to be mixed. This enables satisfactory mixing with the thermosetting resins and, in addition, enables to form integral solidification products in which anion exchange resins and cation exchange resins are not locallized separately and which are homogenous and free from cracks. (T.M.)

Umbilical Cord Management and Stump Care in Normal Childbirth in Slovenian and Croatian Maternity Hospitals.

Science.gov (United States)

Mivšek, Ana Polona; Petročnik, Petra; Skubic, Metka; Škodič Zakšek, Teja; Jug Došler, Anita

2017-12-01

The aim was to investigate first-care procedures for the newborn's umbilical cord at maternity hospitals in Slovenia and Croatia. The study was based on an empirical survey research approach and quantitative research paradigms and included all Slovenian (n=14) and all Croatian (n=35) maternity hospitals. Leaders of midwifery team of 14 Slovenian and 35 Croatian labor wards were invited to participate. The study was conducted in 2013, with 67% of Slovenian and 66% of Croatian maternity hospitals having responded. A causal and non-experimental method of empirical research was used. The research instrument was a questionnaire. Descriptive statistics was used on data analysis. The independence hypothesis was tested with the χ2-test or Kullback 2Î-test. A vast ma-jority of study wards employed delayed umbilical cord clamping, i.e. clamping the cord after pulsa-tion had ceased. Only 10% of Slovenian in comparison with 36.4% of Croatian maternity hospitals practiced dry cord care. Others applied disinfectant on the cord, in Slovenia most frequently 6% po-tassium permanganate, and in Croatia a combination of octenidine and phenoxyethanol. Most Croa-tian -maternity wards (95.7%) still covered the stump, while it was not regular practice in Slovenia. The authors estimate that the prevailing Slovenian and Croatian practices in regard to cord clamping are in accordance with the evidence, while improvements could be made regarding stump care, since dry cord care is the recommended method.

Action of ionizing radiation on epoxy resins

Energy Technology Data Exchange (ETDEWEB)

Van de Voorde, M. E.

1970-12-01

The resistance of classical and experimental epoxy resins to irradiation was studied. The resistance to irradiation of epoxy resins of diverse compositions as well as the development of resins having a radioresistance that approaches that of certain ceramics are discussed. Sources of irradiation and the techniques of dosimetry used are described. The structures of certain epoxy resins and of hardeners are given. The preparation of these resins and their physical properties is described. The effects of radiation on epoxy resins, as well as conditions of irradiation, and suggested mechanisms for degradation of the irradiated resins are discussed. The relationship between chemical structure of the resins and their physical properties is evaluated. (115 references) (JCB)

Epoxidation of linseed oil-Alkyd resins

International Nuclear Information System (INIS)

Motawie, A.M.; Ismail, E.A.; Mazroua, A.M.; Abd EI Aziem, M.S.; Ramadan, A.M.

2004-01-01

Three types of different linseed oil-alkyd resin ( Alk (I), Alk (II), and Alk (III) ) were prepared with the calculated amounts of mono glycerides and adipic acid (1:1, 1:2, and 2:1 Eq.Wt) respectively via monoglyceride method. The obtained alkyd resins were epoxidized via reaction with the calculated quantities of peracetic acid, which was prepared by the reaction of acetic anhydride with H 2 O 2 . Epoxidation occurred with the ratio (1: 1, 1 :3, and 1:6 Eq. Wt) of alkyd to peracetic acid. The effect of reaction time on the epoxy group content was measured during the epoxidation process. The prepared alkyd resins were analyzed by IR and H 1 NMR. The metal coated film properties of epoxidized alkyd resins were compared with those of unmodified alkyd resins. It was observed that the coating films of epoxidized alkyd resins have better in drying properties, hardness, adhesion, impact and flexibility than those of un epoxidized alkyd resins. The flammability properties of the paper coated films for the prepared brominated epoxidized alkyd resins were found to be fire retardant

Oxygen index tests of thermosetting resins

Science.gov (United States)

Gilwee, W. J., Jr.; Parker, J. A.; Kourtides, D. A.

1980-01-01

The flammability characteristics of nine thermosetting resins under evaluation for use in aircraft interiors are described. These resins were evaluated using the Oxygen Index (ASTM 2863) testing procedure. The test specimens consisted of both neat resin and glass reinforced resin. When testing glass-reinforced samples it was observed that Oxygen Index values varied inversely with resin content. Oxygen values were also obtained on specimens exposed to temperatures up to 300 C. All specimens experienced a decline in Oxygen Index when tested at an elevated temperature.

Study on the pyrolysis of phenol-formaldehyde (PF) resin and modified PF resin

Energy Technology Data Exchange (ETDEWEB)

Wang, Jigang, E-mail: wangjigang@seu.edu.cn [Jiangsu Key Laboratory of Advanced Metallic Materials, School of Materials Science and Engineering, Southeast University, Nanjing 211189 (China); Jiang, Haiyun [Jiangsu Key Laboratory of Advanced Metallic Materials, School of Materials Science and Engineering, Southeast University, Nanjing 211189 (China); School of Materials Science and Engineering, Southeast University, Nanjing Institute of Technology, Nanjing 210013 (China); Jiang, Nan [Institute of Theoretical and Computational Chemistry, Nanjing University, Nanjing 210093 (China)

2009-12-10

The pyrolysis of pure phenol-formaldehyde (PF) resin and boron carbide (B{sub 4}C) modified PF resin was investigated by using thermogravimetry (TG) and pyrolysis gas-chromatography-mass-spectrometry (PY-GC/MS). Scanning electron microscope (SEM) and Fourier transform infrared (FT-IR) spectroscopy were also employed to investigate the micro-structural evolution. It was shown from the TG analysis that the char residues of pure PF resin were 62.9 and 60.5% after being pyrolyzed at 700 and 1000 {sup o}C, respectively. The degradation and failure of the resin matrix were mainly resulted from the release of volatiles. The phenol and its methyl derivates took a large proportion in the amount of volatiles. In comparison with the pure PF resin, the char residues of B{sub 4}C modified PF resin were obviously higher, with the values of 71.9 and 68.4% at 700 and 1000 {sup o}C, respectively. Due to the oxidation-reduction reactions between B{sub 4}C additive and oxygen-containing volatiles including CO and H{sub 2}O, partial carbon and oxygen elements in the volatiles remained in the resin matrix in the forms of amorphous carbon and B{sub 2}O{sub 3}, respectively. The results of SEM and FT-IR characterization demonstrated the occurrence of the modification, and the amorphous carbon existed in the form of reticular substance. In addition, the amount of the released phenol and its methyl derivates was also decreased drastically due to the formation of borate.

Contact allergy to epoxy resin

DEFF Research Database (Denmark)

Bangsgaard, Nannie; Thyssen, Jacob Pontoppidan; Menné, Torkil

2012-01-01

Background. Epoxy resin monomers are strong skin sensitizers that are widely used in industrial sectors. In Denmark, the law stipulates that workers must undergo a course on safe handling of epoxy resins prior to occupational exposure, but the effectiveness of this initiative is largely unknown...... in an educational programme. Conclusion. The 1% prevalence of epoxy resin contact allergy is equivalent to reports from other countries. The high occurrence of epoxy resin exposure at work, and the limited use of protective measures, indicate that reinforcement of the law is required....

Input to Resin Column Structural Analysis if Autocatalytic Resin Reaction Occurs in HB-Line Phase II

Energy Technology Data Exchange (ETDEWEB)

Hallman, D.F.

2001-07-10

Solutions of plutonium in nitric acid are purified and concentrated using anion resin prior to precipitation. There have been instances of resin column explosions caused by autocatalytic reactions of anion resins in nitric acid within the DOE complex

Thermosetting behavior of pitch-resin from heavy residue

Energy Technology Data Exchange (ETDEWEB)

Qingfang, Z.; Yansheng, G.; Baohua, H.; Yuzhen, Z. [China Univ. of Petroleum, Dongying, Shandong (China). State Key LAboratory of Heavy Oil Processing, Heavy Oil Research Inst.

2006-07-01

Thermosetting resins are widely employed as a basic matrix for c/c composites in carbon materials production. A new type of synthesized thermosetting resin is called pitch resin. Pitch resin is a cheaper resin and possesses a potential opportunity for future use. However, the thermosetting behavior of pitch resin is not very clear. The hardening process and conditions for thermosetting are very important for future use of pitch resin. B-stage pitch resin is a soluble and meltable inter-media condensed polymer, which is not fully reacted and is of a low molecular weight. The insoluble and unmelted pitch resin can only be obtained from synthesized B-stage resin after a hardening stage. This paper presented an experiment that synthesized B-stage pitch resin with a link agent (PXG) under catalyst action from fluid catalytic cracking (FCC) of the slurry's aromatic enriched component (FCCDF). The paper discussed the experiment, including the synthesis of pitch resin and thermosetting of pitch resin. Two kinds of thermosetting procedures were used in the study called one-step thermosetting and two-step thermosetting. It was concluded that the B-stage pitch resin could be hardened after a thermosetting procedure by heat treatment. The thermosetting pitch resin from 2-step thermosetting possesses was found to have better thermal resistant properties than that of the 1-step thermosetting pitch resin. 13 refs., 2 tabs., 6 figs.

Ponderosa pine resin defenses and growth: metrics matter.

Science.gov (United States)

Hood, Sharon; Sala, Anna

2015-11-01

Bark beetles (Coleoptera: Curculionidae, Scolytinae) cause widespread tree mortality in coniferous forests worldwide. Constitutive and induced host defenses are important factors in an individual tree's ability to survive an attack and in bottom-up regulation of bark beetle population dynamics, yet quantifying defense levels is often difficult. For example, in Pinus spp., resin flow is important for resistance to bark beetles but is extremely variable among individuals and within a season. While resin is produced and stored in resin ducts, the specific resin duct metrics that best correlate with resin flow remain unclear. The ability and timing of some pine species to produce induced resin is also not well understood. We investigated (i) the relationships between ponderosa pine (Pinus ponderosa Lawson & C. Lawson) resin flow and axial resin duct characteristics, tree growth and physiological variables, and (ii) if mechanical wounding induces ponderosa pine resin flow and resin ducts in the absence of bark beetles. Resin flow increased later in the growing season under moderate water stress and was highest in faster growing trees. The best predictors of resin flow were nonstandardized measures of resin ducts, resin duct size and total resin duct area, both of which increased with tree growth. However, while faster growing trees tended to produce more resin, models of resin flow using only tree growth were not statistically significant. Further, the standardized measures of resin ducts, density and duct area relative to xylem area, decreased with tree growth rate, indicating that slower growing trees invested more in resin duct defenses per unit area of radial growth, despite a tendency to produce less resin overall. We also found that mechanical wounding induced ponderosa pine defenses, but this response was slow. Resin flow increased after 28 days, and resin duct production did not increase until the following year. These slow induced responses may allow

Ion chromatography for the analysis of salt splitting capacities of cation and anion resin in premixed resin sample

International Nuclear Information System (INIS)

Ghosh, Satinath; Kumar, Rakesh; Tripathy, M.K.; Dhole, K.; Sharma, R.S.; Varde, P.V.

2017-01-01

Mixed bed ion exchange resin is commonly used in various plants including nuclear reactors for the purpose of fine polishing. The analysis of ion exchange capacities of cation and anion resin in resin mixture is therefore an agenda in the context of purchasing of premixed resin from the manufacturer. An ion chromatographic method for assaying ion exchange capacities of pure as well as mixed resin has been optimized. The proposed method in contrast to the conventional ASTM method has been found to be quite encouraging to consider it as an alternate method for the analysis of premixed resin. (author)

Biphenyl liquid crystalline epoxy resin as a low-shrinkage resin-based dental restorative nanocomposite.

Science.gov (United States)

Hsu, Sheng-Hao; Chen, Rung-Shu; Chang, Yuan-Ling; Chen, Min-Huey; Cheng, Kuo-Chung; Su, Wei-Fang

2012-11-01

Low-shrinkage resin-based photocurable liquid crystalline epoxy nanocomposite has been investigated with regard to its application as a dental restoration material. The nanocomposite consists of an organic matrix and an inorganic reinforcing filler. The organic matrix is made of liquid crystalline biphenyl epoxy resin (BP), an epoxy resin consisting of cyclohexylmethyl-3,4-epoxycyclohexanecarboxylate (ECH), the photoinitiator 4-octylphenyl phenyliodonium hexafluoroantimonate and the photosensitizer champhorquinone. The inorganic filler is silica nanoparticles (∼70-100 nm). The nanoparticles were modified by an epoxy silane of γ-glycidoxypropyltrimethoxysilane to be compatible with the organic matrix and to chemically bond with the organic matrix after photo curing. By incorporating the BP liquid crystalline (LC) epoxy resin into conventional ECH epoxy resin, the nanocomposite has improved hardness, flexural modulus, water absorption and coefficient of thermal expansion. Although the incorporation of silica filler may dilute the reinforcing effect of crystalline BP, a high silica filler content (∼42 vol.%) was found to increase the physical and chemical properties of the nanocomposite due to the formation of unique microstructures. The microstructure of nanoparticle embedded layers was observed in the nanocomposite using scanning and transmission electron microscopy. This unique microstructure indicates that the crystalline BP and nanoparticles support each other and result in outstanding mechanical properties. The crystalline BP in the LC epoxy resin-based nanocomposite was partially melted during exothermic photopolymerization, and the resin expanded via an order-to-disorder transition. Thus, the post-gelation shrinkage of the LC epoxy resin-based nanocomposite is greatly reduced, ∼50.6% less than in commercialized methacrylate resin-based composites. This LC epoxy nanocomposite demonstrates good physical and chemical properties and good biocompatibility

Overview on resins available in microlithography

International Nuclear Information System (INIS)

Serre, B.; Schue, F.; Montginoul, C.; Giral, L.

1985-01-01

Lithographic equipments using electrons and X radiation are developed. Velocity and resolution requirements fix the nature of the material to irradiate. Circuit making principles are recalled here; resists (organic polymers) are employed for it. The different types of resins and then needed characteristics are reviewed here. In the scope of electron sensitive resins methyl polymethacrylate and derivative and its copolymers (and copolymers of methacrylonitrile) and reticulated copolymers are studied. Polysulfones are also presented (poly(buten-1 sulfone), poly(styrene sulfone), poly(methyl-1 cyclopentene-1 sulfone). The interest in photosensitive resins (such as AZ) as electron sensitive resins is recalled. In the field of negative resins, the polyepoxyds, polystyrene and halogenated derivates from polystyrene (CMS and PCMS), the poly(vinyl-2 naphtalene) and its derivatives (PSTTF) are presented. The X radiation sensitive resins are also reviewed: the methyl polymethacrylate and its halogenated derivates, the acrylic homopolymers and copolymers (example of poly(acrylate of chlorinated alcoyls). The resins developable by plasma are mentioned. At last, for photosensitive resins, the diazide polydiene systems are presented together with systems diazo-2 2H-naphtalenone-1. The systems with salt photolysis are just recalled [fr

Effects of layering technique on the shade of resin overlays and the microhardness of dual cure resin cement

Directory of Open Access Journals (Sweden)

Hoon-Sang Chang

2014-06-01

Full Text Available The purpose of this study was to assess the color of layered resin overlays and to test the early microhardness of dual cure resin cement (DCRC light cured through the layered resin overlays. Resin overlays of 1.5 mm thickness were fabricated with the A3 shade of Z350 (Group 1L, the A3B and A3E shades of Supreme XT (Group 2L, and the A3, E3, and T1 shades of Sinfony (Group 3L using one, two, and three layers, respectively (n = 7. Each layer of the resin overlays was set in equal thickness. The color of the resin overlays was measured with a colorimeter and compared with an A3 shade resin denture tooth. DCRC was light cured through the resin overlays, and the early microhardness of the DCRC was measured. The ΔE value between the denture tooth and the resin overlays and the Vickers hardness number (VHN of the DCRC were analyzed with one-way ANOVA and Tukey’s HSD test. The color differences were 8.9 ± 0.5, 5.3 ± 1.0, and 7.3 ± 0.5 and the VHNs were 19.4 ± 1.1, 21.1 ± 0.9, and 29.3 ± 0.6 for Groups 1L, 2L, and 3L, respectively. Therefore, to match the designated tooth color of resin inlays and to increase the early microhardness of DCRC, layered resin inlays are more appropriate than single-dentin-layer resin inlays. However, the translucent layer should be used cautiously because the color difference of resin inlays with a translucent layer was affected more than those without a translucent layer.

Resin for processing radioactive waste water

International Nuclear Information System (INIS)

Onozuka, Teruo; Shindo, Manabu; Kiba, Hideaki; Kubota, Hirohisa; Sawada, Shintaro.

1995-01-01

The present invention concerns an anionic exchange resin having a long service life with less radiation degradation. The resin is an anionic exchange resin in which a trimethyl ammonium group is introduced to a copolymer of 4-bromo-butoxymethyl styrene and divinyl benzene. The resin is excellent in economic performance, and can reduce the frequency for the exchange of cross-linked anionic exchangers. (T.M.)

Resin for processing radioactive waste water

Energy Technology Data Exchange (ETDEWEB)

Onozuka, Teruo; Shindo, Manabu [Tohoku Electric Power Co., Inc., Sendai (Japan); Kiba, Hideaki; Kubota, Hirohisa; Sawada, Shintaro

1995-11-07

The present invention concerns an anionic exchange resin having a long service life with less radiation degradation. The resin is an anionic exchange resin in which a trimethyl ammonium group is introduced to a copolymer of 4-bromo-butoxymethyl styrene and divinyl benzene. The resin is excellent in economic performance, and can reduce the frequency for the exchange of cross-linked anionic exchangers. (T.M.).

Bulk-Fill Resin Composites

DEFF Research Database (Denmark)

Benetti, Ana Raquel; Havndrup-Pedersen, Cæcilie; Honoré, Daniel

2015-01-01

the restorative procedure. The aim of this study, therefore, was to compare the depth of cure, polymerization contraction, and gap formation in bulk-fill resin composites with those of a conventional resin composite. To achieve this, the depth of cure was assessed in accordance with the International Organization...... for Standardization 4049 standard, and the polymerization contraction was determined using the bonded-disc method. The gap formation was measured at the dentin margin of Class II cavities. Five bulk-fill resin composites were investigated: two high-viscosity (Tetric EvoCeram Bulk Fill, SonicFill) and three low......-viscosity (x-tra base, Venus Bulk Fill, SDR) materials. Compared with the conventional resin composite, the high-viscosity bulk-fill materials exhibited only a small increase (but significant for Tetric EvoCeram Bulk Fill) in depth of cure and polymerization contraction, whereas the low-viscosity bulk...

[Physical properties of resins for veneer crown. (Part 1) Bending strength of thermosetting methacrylic resins (author's transl)].

Science.gov (United States)

Kashiwada, T

1979-01-01

The physical properties of thermosetting methacrylic resins contain a kind or more than two kinds of cross linking agents were investigated. Knoop hardness and bending strength after drying, water sorption and thermal cycling were listed in table 4 and 5. Hydrophilic resins absorbed water about 3 times as much as hydrophobic resins. The materials contain a small amount of hydrophobic cross linking agents in MMA indicate comparatively excellent properties after drying, water sorption and thermal cycling. Knoop hardness of resins generally reduced by water sorption, especially in the case of the resin contains a large amount of triethylene glycol dimethacrylate.

Curing reaction of bisphenol-A based benzoxazine with cyanate ester resin and the properties of the cured thermosetting resin

Directory of Open Access Journals (Sweden)

H. Kimura

2011-12-01

Full Text Available Curing reaction of bisphenol-A based benzoxazine with cyanate ester resin and the properties of the cured thermosetting resin were investigated. The cure behavior of benzoxazine with cyanate ester resin was monitored by model reaction using nuclear magnetic resonance (NMR. As a result of the model reaction, the ring opening reaction of benzoxazine ring and thermal self-cyclotrimerization of cyanate ester group occurred, and then the phenolic hydoroxyl group generated by the ring opening reaction of benzoxazine ring co-reacted with cyanate ester group. The properties of the cured thermosetting resin were estimated by mechanical properties, electrical resistivity, water resistance and heat resistance. The cured thermosetting resin from benzoxazine and cyanate ester resin showed good heat resistance, high electrical resistivity and high water resistance, compared with the cured thermosetting resin from benzoxazine and epoxy resin.

Removal of radiocesium using cation exchange resin

International Nuclear Information System (INIS)

Morita-Murase, Yuko; Mizumura, Ryosuke; Tachibana, Yoshitaka; Kanazawa, Hideko

2013-01-01

Cation exchange resins (calcium polystyrene sulfonate, Ca-resin and sodium polystyrene sulfonate, Na-resin) have been used as agents to improve hyperkerlemia. For removing 137 Cs from the human body, the adsorption ability of the resin for 137 Cs was examined and evaluated. Resin (0.03 g) and 137 Cs (ca.1 kBq) were introduced into 3 mL of water, the Japanese Pharmacopoeia 1st fluid for a dissolution test (pH 1.2) and 2nd fluid (pH 6.8), respectively, and shaken. After 1-3 hours, the 137 Cs adsorption (%) of Na-resin was 99% in water, 60% in a pH 1.2 fluid and, 66% in a pH 6.8 fluid. By adding potassium, the 137 Cs adsorption (%) of Ca-resin was reduced. However, the 137 Cs adsorption (%) of Na-resin was almost unchanged. These results show that both resins have adsorption ability for 137 Cs in the stomach and the intestines. Therefore, the proposed method will be an effective means in the case of a radiological emergency due to 137 Cs. (author)

Novel silica-based ion exchange resin

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-11-01

Eichrom`s highly successful Diphonixo resin resembles a conventional ion exchange resin in its use of sulfonic acid ligands on a styrene- divinylbenzene matrix. Diphonix resin exhibits rapid exchange kinetics that allow economical operation of ion exchange systems. Unlike conventional resins, Diphonix resin contains chelating ligands that are diphosphonic acid groups that recognize and remove the targeted metals and reject the more common elements such as sodium, calcium and magnesium. This latter property makes Diphonix ideal for many industrial scale applications, including those involving waste treatment. For treatment of low-level, transuranic (TRU) and high- level radioactive wastes, Diphonix`s polystyrene backbone hinders its application due to radiolytic stability of the carbon-hydrogen bonds and lack of compatibility with expected vitrification schemes. Polystyrene-based Diphonix is approximately 60% carbon- hydrogen. In response to an identified need within the Department of Energy for a resin with the positive attributes of Diphonix that also exhibits greater radiolytic stability and final waste form compatibility, Eichrom has successfully developed a new, silica-based resin version of Diphonix. Target application for this new resin is for use in environmental restoration and waste management situations involving the processing of low-level, transuranic and high-level radioactive wastes. The resin can also be used for processing liquid mixed waste (waste that contains low level radioactivity and hazardous constituents) including mixed wastes contaminated with organic compounds. Silica-based Diphonix is only 10% carbon-hydrogen, with the bulk of the matrix silica.

Measurement of opalescence of resin composites.

Science.gov (United States)

Lee, Yong-Keun; Lu, Huan; Powers, John M

2005-11-01

Opalescence is an optical property, where there is light scattering of the shorter wavelengths of the visible spectrum, giving the material a bluish appearance under reflected light and an orange/brown appearance under transmitted light. The objective of this study was to determine the opalescence of resin composites with a color measuring spectrophotometer. Colors of A2 and enamel or translucent shades of four resin composites and of an unfilled resin measured in the reflectance and transmittance modes were compared, and the opalescence parameter (OP) was calculated as the difference in blue-yellow coordinate (Deltab*) and red-green parameter (Deltaa*) between the reflected and transmitted colors of 1-mm thick specimens. The masking effect was calculated as the color difference between the color of a black background and the color of specimen over the black background. The range of OP in resin composites was 5.7-23.7, which was higher than that of the unfilled resin. However, there were significant differences among the brands and shades of the resin composites. Opalescence varied by brand and shade of the resin composites, and contributed to the masking of background color along with translucency parameter. Some of the resin composites actually displayed opalescence.

Disposal of bead ion exchange resin wastes

International Nuclear Information System (INIS)

Gay, R.L.; Granthan, L.F.

1985-01-01

Bead ion exchange resin wastes are disposed of by a process which involves spray-drying a bead ion exchange resin waste in order to remove substantially all of the water present in such waste, including the water on the surface of the ion exchange resin beads and the water inside the ion exchange resin beads. The resulting dried ion exchange resin beads can then be solidified in a suitable solid matrix-forming material, such as a polymer, which solidifies to contain the dried ion exchange resin beads in a solid monolith suitable for disposal by burial or other conventional means

Curing kinetics of alkyd/melamine resin mixtures

Directory of Open Access Journals (Sweden)

Jovičić Mirjana C.

2009-01-01

Full Text Available Alkyd resins are the most popular and useful synthetic resins applied as the binder in protective coatings. Frequently they are not used alone but are modified with other synthetic resins in the manufacture of the coatings. An alkyd/melamine resin mixture is the usual composition for the preparation of coating called 'baking enamel' and it is cured through functional groups of resins at high temperatures. In this paper, curing kinetics of alkyd resins based on castor oil and dehydrated castor oil with melamine resin, has been studied by DSC method with programmed heating and in isothermal mode. The results determined from dynamic DSC curves were mathematically transformed using the Ozawa isoconversional method for obtaining the isothermal data. These results, degree of curing versus time, are in good agreement with those determined by the isothermal DSC experiments. By applying the Ozawa method it is possible to calculate the isothermal kinetic parameters for the alkyd/melamine resin mixtures curing using only calorimetric data obtained by dynamic DSC runs. Depending on the alkyd resin type and ratio in mixtures the values of activation energies of curing process of resin mixtures are from 51.3 to 114 kJ mol-1. The rate constant of curing increases with increasing the content of melamine resin in the mixture and with curing temperature. The reaction order varies from 1.12 to 1.37 for alkyd based on dehydrated castor oil/melamine resin mixtures and from 1.74 to 2.03 for mixtures with alkyd based on castor oil. Based on the results obtained, we propose that dehydrated castor oil alkyd/melamine resin mixtures can be used in practice (curing temperatures from 120 to 160°C.

Spray drying of bead resins: feasibility tests

International Nuclear Information System (INIS)

Gay, R.L.; Grantham, L.F.; Jones, L.J.

1984-01-01

Rockwell International has developed a volume reduction system for low-level reactor wastes based on drying the wastes in a heated-air spray dryer. The drying of slurries of sodium sulfate, boric acid, and powdered ion exchange resins was demonstrated in previous tests. The drying of bead ion exchange resins can be especially difficult due to the relatively large size of bead resins (about 500 to 800 microns) and their natural affinity for water. This water becomes part of the pore structure of the resins and normally comprises 50 t 60 wt % of the resin weight. A 76-cm-diameter spray dryer was used for feasibility tests of spray drying of cation and anion bead resins. These resins were fed to the dryer in the as-received form (similar to dewatered resins) and as slurries. A dry, free-flowing product was produced in all the tests. The volume of the spray-dried product was one-half to one-third the volume of the as-received material. An economic analysis was made of the potential cost savings that can be achieved using the Rockwel spray dryer system. In-plant costs, transportation costs, and burial costs of spray-dried resins were compared to similar costs for disposal of dewatered resins. A typical utility producing 170 m 3 (6,000 ft 3 ) per year of dewatered resins can save $600,000 to $700,000 per year using this volume reduction system

Effect of repair resin type and surface treatment on the repair strength of polyamide denture base resin.

Science.gov (United States)

Gundogdu, Mustafa; Yanikoglu, Nuran; Bayindir, Funda; Ciftci, Hilal

2015-01-01

The purpose of the present study was to evaluate the effects of different repair resins and surface treatments on the repair strength of a polyamide denture base material. Polyamide resin specimens were prepared and divided into nine groups according to the surface treatments and repair materials. The flexural strengths were measured with a 3-point bending test. Data were analyzed with a 2-way analysis of variance, and the post-hoc Tukey test (α=0.05). The effects of the surface treatments on the surface of the polyamide resin were examined using scanning electron microscopy. The repair resins and surface treatments significantly affected the repair strength of the polyamide denture base material (p0.05). The flexural strength of the specimens repaired with the polyamide resin was significantly higher than that of those repaired with the heat-polymerized and autopolymerizing acrylic resins.

Solidification of ion exchange resin wastes

International Nuclear Information System (INIS)

1982-08-01

Solidification media investigated included portland type I, portland type III and high alumina cements, a proprietary gypsum-based polymer modified cement, and a vinyl ester-styrene thermosetting plastic. Samples formulated with hydraulic cement were analyzed to investigate the effects of resin type, resin loading, waste-to-cement ratio, and water-to-cement ratio. The solidification of cation resin wastes with portland cement was characterized by excessive swelling and cracking of waste forms, both after curing and during immersion testing. Mixed bed resin waste formulations were limited by their cation component. Additives to improve the mechanical properties of portland cement-ion exchange resin waste forms were evaluated. High alumina cement formulations dislayed a resistance to deterioration of mechanical integrity during immersion testing, thus providing a significant advantage over portland cements for the solidification of resin wastes. Properties of cement-ion exchange resin waste forms were examined. An experiment was conducted to study the leachability of 137 Cs, 85 Sr, and 60 Co from resins modified in portland type III and high alumina cements. The cumulative 137 Cs fraction release was at least an order of magnitude greater than that of either 85 Sr or 60 Co. Release rates of 137 Cs in high alumina cement were greater than those in portland III cement by a factor of two.Compressive strength and leach testing were conducted for resin wastes solidified with polymer-modified gypsum based cement. 137 Cs, 85 Sr, and 60 Co fraction releases were about one, two and three orders of magnitude higher, respectively, than in equivalent portland type III cement formulations. As much as 28.6 wt % dry ion exchange resin was successfully solidified using vinyl ester-styrene compared with a maximum of 25 wt % in both portland and gypsum-based cement

Method for regenerating magnetic polyamine-epichlorohydrin resin

Science.gov (United States)

Kochen, Robert L.; Navratil, James D.

1997-07-29

Magnetic polymer resins capable of efficient removal of actinides and heavy metals from contaminated water are disclosed together with methods for making, using, and regenerating them. The resins comprise polyamine-epichlorohydrin resin beads with ferrites attached to the surfaces of the beads. Markedly improved water decontamination is demonstrated using these magnetic polymer resins of the invention in the presence of a magnetic field, as compared with water decontamination methods employing ordinary ion exchange resins or ferrites taken separately.

Handling sticky resin by stingless bees (Hymenoptera, Apidae

Directory of Open Access Journals (Sweden)

Markus Gastauer

2011-06-01

Full Text Available For their nest defense, stingless bees (Meliponini collect plant resins which they stick on intruders like ants or cleptobiotic robber bees causing their immobilization. The aim of this article is to identify all parts of stingless bee workers contacting these sticky resins. Of special interest are those body parts with anti-adhesive properties to resin, where it can be removed without residues. For that, extensive behavioral observations during foraging flight, handling and application of the resin have been carried out. When handling the resin, all tarsi touch the resin while walking above it. For transportation from plants to the nest during foraging flight, the resin is packed to the corbicula via tarsi and basitarsi of front and middle legs. Once stuck to the resin or after the corbicula had been unloaded, the bee's legs have to be cleaned thoroughly. Only the tips of the mandibles, that form, cut and apply the sticky resin, seem to have at least temporarily resin-rejecting properties.

Microshear bond strength of composite resins to enamel and porcelain substrates utilizing unfilled versus filled resins.

Science.gov (United States)

Najafi-Abrandabadi, Ahmad; Najafi-Abrandabadi, Siamak; Ghasemi, Amir; Kotick, Philip G

2014-11-01

Failures such as marginal discoloration and composite chipping are still the problems of tooth-colored restorations on the substrate of enamel and porcelain, which some of these problems are consequently as a result of failures in the bonding layer. Using filled resin has been recently introduced to increase the bond strength of this layer. The aim of this study was to compare the microshear bond strength (μ-SBS) of composite resins to enamel incubated in periods of 24 h and 9 months and porcelain with unfilled resin and flowable composites (filled resin). In this in vitro study, two groups of 75 enamel samples with different storage times (24 h and 9 months) and a group of 75 porcelain samples were used. They were divided into 5 experimental groups of 15 samples in each. Composite cylinders in tygon tubes were bonded on the surface of acid-etched enamel and pretreated porcelain. Wave, Wave MV, Wave HV, Grandioflow and Margin Bond were used as bonding agents. The μ-SBS was measured at the speed of 1.0 mm/min. The bond strengths were analyzed with one-way analysis of variance (ANOVA) test followed by Tukey test. P composites (filled resins) can be used instead of unfilled resins in bonding composite resins to enamel and porcelain substrates.

Commercial Ion Exchange Resin Vitrification Studies

International Nuclear Information System (INIS)

Cicero-Herman, C.A

2002-01-01

In the nuclear industry, ion exchange resins are used for purification of aqueous streams. The major contaminants of the resins are usually the radioactive materials that are removed from the aqueous streams. The use of the ion exchange resins creates a waste stream that can be very high in both organic and radioactive constituents. Therefore, disposal of the spent resin often becomes an economic problem because of the large volumes of resin produced and the relatively few technologies that are capable of economically stabilizing this waste. Vitrification of this waste stream presents a reasonable disposal alternative because of its inherent destruction capabilities, the volume reductions obtainable, and the durable product that it produces

Decomposing method for ion exchange resin

International Nuclear Information System (INIS)

Sako, Takeshi; Sato, Shinshi; Akai, Yoshie; Moniwa, Shinobu; Yamada, Kazuo

1998-01-01

The present invention concerns a method of decomposing ion exchange resins generated in a nuclear power plant to carbon dioxide reliably in a short period of time. (1) The ion exchange resins are mixed with water, and then they are kept for a predetermined period of time in the presence of an inert gas at high temperature and high pressure exceeding the critical point of water to decompose the ion exchange resins. (2) The ion exchange resins is mixed with water, an oxidant is added and they are kept for a predetermined time in the presence of an inert gas at a high temperature and a high pressure exceeding a critical point of water of an inert gas at a high temperature to decompose the ion exchange resins. (3) An alkali or acid is added to ion exchange resins and water to control the hydrogen ion concentration in the solution and the ion exchange resins are decomposed in above-mentioned (1) or (2). Sodium hydroxide is used as the alkali and hydrochloric acid is used as the acid. In addition, oxygen, hydrogen peroxide or ozone is used as an oxidant. (I.S.)

Bending characteristics of resin concretes

Directory of Open Access Journals (Sweden)

Ribeiro Maria Cristina Santos

2003-01-01

Full Text Available In this research work the influence of composition and curing conditions in bending strength of polyester and epoxy concrete is analyzed. Various mixtures of resin and aggregates were considered in view of an optimal combination. The Taguchi methodology was applied in order to reduce the number of tests, and in order to evaluate the influence of various parameters in concrete properties. This methodology is very useful for the planning of experiments. Test results, analyzed by this methodology, shown that the most significant factors affecting bending strength properties of resin concretes are the type of resin, resin content and charge content. An optimal formulation leading to a maximum bending strength was achieved in terms of material parameters.

Resin Flow in Fiber Preformed by Vacuum Assisted Resin Transfer Molding with Flexible Tools

Directory of Open Access Journals (Sweden)

M.M. Shokrieh

2008-12-01

Full Text Available Vacuum assisted resin transfer molding, as a sub-branch of RTM is a method of manufacturing composite specimens. Considering the industrial development of this method, different modified techniques are designed to improve its performance. Among these techniques, using a half flexible mold is regarded as an important method. In this work, dominant equations of resin flow through the mold in polar coordinates are solved analytically. Based on this approach, closed-form solutions have been presented for different parameters such as thickness variation of preformed fiber, resin pressure, resin velocity and fiber volume fraction as functions of two variables, namely, time and the distance from injection port. After verification of the approach employed in this work, the results are presented. Important parameters influencing the quality and the rate production are studied in detail.

Microhardness of dual-polymerizing resin cements and foundation composite resins for luting fiber-reinforced posts.

Science.gov (United States)

Yoshida, Keiichi; Meng, Xiangfeng

2014-06-01

The optimal luting material for fiber-reinforced posts to ensure the longevity of foundation restorations remains undetermined. The purpose of this study was to evaluate the suitability of 3 dual-polymerizing resin cements and 2 dual-polymerizing foundation composite resins for luting fiber-reinforced posts by assessing their Knoop hardness number. Five specimens of dual-polymerizing resin cements (SA Cement Automix, G-Cem LincAce, and Panavia F2.0) and 5 specimens of dual-polymerizing foundation composite resins (Clearfil DC Core Plus and Unifil Core EM) were polymerized from the top by irradiation for 40 seconds. Knoop hardness numbers were measured at depths of 0.5, 2.0, 4.0, 6.0, 8.0, and 10.0 mm at 0.5 hours and 7 days after irradiation. Data were statistically analyzed by repeated measures ANOVA, 1-way ANOVA, and the Tukey compromise post hoc test (α=.05). At both times after irradiation, the 5 resins materials showed the highest Knoop hardness numbers at the 0.5-mm depth. At 7 days after irradiation, the Knoop hardness numbers of the resin materials did not differ significantly between the 8.0-mm and 10.0-mm depths (P>.05). For all materials, the Knoop hardness numbers at 7 days after irradiation were significantly higher than those at 0.5 hours after irradiation at all depths (Presin materials were found to decrease in the following order: DC Core Plus, Unifil Core EM, Panavia F2.0, SA Cement Automix, and G-Cem LincAce (Pcomposite resins were higher than those of the 3 dual-polymerizing resin cements, notable differences were seen among the 5 materials at all depths and at both times after irradiation. Copyright © 2014 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Organic geochemistry of resins from modern Agathis australis and Eocene resins from New Zealand: Diagenetic and taxonomic implications

Science.gov (United States)

Lyons, P.C.; Mastalerz, Maria; Orem, W.H.

2009-01-01

A maturation series of resins and fossil resins from New Zealand, ranging in age from Modern to Eocene and ranging from uncoalified to high volatile C bituminous coal, were analyzed by elemental, pyrolysis-gas chromatography (Py-GC), Fourier Transform infrared (FTir), and solid-state 13C nuclear magnetic resonance (13C NMR) techniques. For comparison, four resin samples from the Latrobe Valley, Australia, were analyzed. All of the resins and fossil resins of this study show very high H/C atomic ratios, and are characterized by dominant peaks in the 10-60??ppm range of solid-state 13C NMR spectra and prominent bands in the aliphatic stretching region (2800-3000??cm- 1) of FTir spectra, all indicating a highly aliphatic molecular structure. The 13C NMR and FTir data indicate a diterpenoid structure for these resins. There is an abrupt loss of oxygen that occurs at the Lignite A/Subbituminous C stage, which is attributed to a dramatic loss of carboxyl (COOH) from the diterpenoid molecule. This is a new finding in the diagenesis of resins. This important loss in oxygenated functional groups is attributed to a maturation change. Also, there is a progressive loss of exomethylene (CH2) groups with increasing degree of maturation, as shown by both 13C NMR and FTir data. This change has been noted by previous investigators. Exomethylene is absent in the fossil resins from the Eocene high volatile C bituminous coals. This progressive loss is characteristic of Class I resinites. FTir data indicate that the oxygenated functional groups are strong in all the resin samples except the fossil resin from high volatile C bituminous coal. This important change in oxygenated functional groups is attributed to maturation changes. The 13C NMR and FTir data indicate there are minor changes in the Agathis australis resin from the living tree and soil, which suggests that alteration of A. australis resins begins shortly after deposition in the soil for as little as 1000??years. The Morwell

Organic geochemistry of resins from modern Agathis australis and Eocene resins from New Zealand: Diagenetic and taxonomic implications

Energy Technology Data Exchange (ETDEWEB)

Lyons, Paul C. [Lyons and Associates Consultants, 206 Amber Road, Middleboro, MA 02346 (United States); Mastalerz, Maria [Indiana Geological Survey, Indiana University, 611 North Walnut Grove, Bloomington, IN 47405 (United States); Orem, William H. [U.S. Geological Survey, MS 956 National Center, Reston, VA 20192 (United States)

2009-10-01

A maturation series of resins and fossil resins from New Zealand, ranging in age from Modern to Eocene and ranging from uncoalified to high volatile C bituminous coal, were analyzed by elemental, pyrolysis-gas chromatography (Py-GC), Fourier Transform infrared (FTir), and solid-state {sup 13}C nuclear magnetic resonance ({sup 13}C NMR) techniques. For comparison, four resin samples from the Latrobe Valley, Australia, were analyzed. All of the resins and fossil resins of this study show very high H/C atomic ratios, and are characterized by dominant peaks in the 10-60 ppm range of solid-state {sup 13}C NMR spectra and prominent bands in the aliphatic stretching region (2800-3000 cm{sup -} {sup 1}) of FTir spectra, all indicating a highly aliphatic molecular structure. The {sup 13}C NMR and FTir data indicate a diterpenoid structure for these resins. There is an abrupt loss of oxygen that occurs at the Lignite A/Subbituminous C stage, which is attributed to a dramatic loss of carboxyl (COOH) from the diterpenoid molecule. This is a new finding in the diagenesis of resins. This important loss in oxygenated functional groups is attributed to a maturation change. Also, there is a progressive loss of exomethylene (CH{sub 2}) groups with increasing degree of maturation, as shown by both {sup 13}C NMR and FTir data. This change has been noted by previous investigators. Exomethylene is absent in the fossil resins from the Eocene high volatile C bituminous coals. This progressive loss is characteristic of Class I resinites. FTir data indicate that the oxygenated functional groups are strong in all the resin samples except the fossil resin from high volatile C bituminous coal. This important change in oxygenated functional groups is attributed to maturation changes. The {sup 13}C NMR and FTir data indicate there are minor changes in the Agathis australis resin from the living tree and soil, which suggests that alteration of A. australis resins begins shortly after deposition

SHALLOW SHELL RESIN VERSUS TRADITIONAL RESIN: A CASE STUDY FOR Cu(II REMOVAL

Directory of Open Access Journals (Sweden)

Özgür Arar

2016-10-01

Full Text Available A comparative study on Cu2+ removal by shallow shell resin (Purolite SST 60 and traditional strongly acidic cation exchange resin (Purolite PFC 100 was performed. Batch experiments were carried out as a function of  resin  dosage and  solution pH and contact time. Ion exchange reaction showed a pH depended feature.  Maximum removal of Cu2+ achieved  pH  from 2 to 5. Sorption isothermal data is well interpreted by the Langmuir equation. Additionally, kinetic experiments showed that the pseudo first-order model was suitable for such resins. The regeneration performance of shallow shell technology (SST resin is better than PFC 100.  A solution of 2M H2SO4 performed well in regenerationof SST 60 resin. On the other han maximum regeneration reached 80% for PFC 100 resin.Özet: Bu çalışmada, klasik iyon değiştirici reçine (Purolite PFC 100 ve  sığ kabuk  reçine (Purolite SST 60  ile Cu2+ giderilmesi incelenmiştir. Yapılan kesikli çalışmalarla Cu2+ giderilmesine, reçine miktarı, çözelti pH`ı ve temas süresinin etkisi incelenmiştir. Çözelti pH`ının 2 ile 5 arasında olduğu durumda Cu2+ iyonları tamamen giderilmiştir. Denge çalışmalarında elde edilen sonuçlar Langmuir izoterm modeline daha uygun olmuştur. Kinetik çalışmalarda elde edilen sonuçlar yalancı birinci mertebe kinetik modeline uygunluk göstermişir. SST 60 reçinesinin rejenerasyon verimi PFC 100 reçinesinden daha yüksektir. 2M H2SO4 ile SST 60 reçinesi tamamen rejenere edilmiştir.

5-year clinical performance of resin composite versus resin modified glass ionomer restorative system in non-carious cervical lesions

DEFF Research Database (Denmark)

Franco, Eduardo Batista; Benetti, Ana Raquel; Ishikiriama, Sérgio Kiyoshi

2006-01-01

To comparatively assess the 5-year clinical performance of a 1-bottle adhesive and resin composite system with a resin-modified glass ionomer restorative in non-carious cervical lesions.......To comparatively assess the 5-year clinical performance of a 1-bottle adhesive and resin composite system with a resin-modified glass ionomer restorative in non-carious cervical lesions....

Test Production of Anti-Corrosive Paint in Laboratory Scale

International Nuclear Information System (INIS)

Thein Thein Win, Daw; Khin Aye Tint, Daw; Wai Min Than, Daw

2003-02-01

The main purpose of this project is to produce the anti-corrosive paint in laboratory scale. In these experiments, local raw materials, natural resin (shellac), pine oil, turpentine and ethyl alcohol wer applied basically. Laboratory trials were undrtaken to determine the suitablity of raw materials ane their composition for anti-corrosive paint manufacture.The results obtained show that the anti-corrosive paint from experiment No.(30) is suitable for steel plate and this is also considered commercially economics

Effect of Resin Coating and Chlorhexidine on Microleakage of Two Resin Cements after Storage

Directory of Open Access Journals (Sweden)

F. Shafie

2010-03-01

Full Text Available Objective: Evaluating the effect of resin coating and chlorhexidine on microleakage of two resin cements after water storage.Materials and Methods: Standardized class V cavities were prepared on facial and lingual surfaces of one hundred twenty intact human molars with gingival margins placed 1mm below the cemento-enamel junction. Indirect composite inlays were fabricated and thespecimens were randomly assigned into 6 groups. In Groups 1 to 4, inlays were cemented with Panavia F2.0 cement. G1: according to the manufacturer’s instruction. G2: with light cured resin on the ED primer. G3: chlorhexidine application before priming. G4: withchlorhexidine application before priming and light cured resin on primer. G5: inlays were cemented with Nexus 2 resin cement. G6: chlorhexidine application after etching. Each group was divided into two subgroups based on the 24-hour and 6-month water storagetime. After preparation for microleakage test, the teeth were sectioned and evaluated at both margins under a 20×stereomicroscope. Dye penetration was scored using 0-3 criteria.The data was analyzed using Kruskal-Wallis and complementary Dunn tests.Results: There was significantly less leakage in G2 and G4 than the Panavia F2.0 control group at gingival margins after 6 months (P<0.05. There was no significant differences in leakage between G1 and G3 at both margins after 24 hours and 6 months storage. After 6months, G6 revealed significantly less leakage than G5 at gingival margins (P=0.033. In general, gingival margins showed more leakage than occlusal margins.Conclusion: Additionally, resin coating in self-etch (Panavia F2.0 and chlorhexidine application in etch-rinse (Nexus resin cement reduced microleakage at gingival margins after storage.

21 CFR 177.1680 - Polyurethane resins.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Polyurethane resins. 177.1680 Section 177.1680 Food... of Single and Repeated Use Food Contact Surfaces § 177.1680 Polyurethane resins. The polyurethane...) For the purpose of this section, polyurethane resins are those produced when one or more of the...

Safety evaluation of cation-exchange resins

International Nuclear Information System (INIS)

Kalkwarf, D.R.

1977-08-01

Results are presented of a study to evaluate whether sufficient information is available to establish conservative limits for the safe use of cation-exchange resins in separating radionuclides and, if not, to recommend what new data should be acquired. The study was also an attempt to identify in-line analytical techniques for the evaluation of resin degradation during radionuclide processing. The report is based upon a review of the published literature and upon discussions with many people engaged in the use of these resins. It was concluded that the chief hazard in the use of cation-exchange resins for separating radionuclides is a thermal explosion if nitric acid or other strong oxidants are present in the process solution. Thermal explosions can be avoided by limiting process parameters so that the rates of heat and gas generation in the system do not exceed the rates for their transfer to the surroundings. Such parameters include temperature, oxidant concentration, the amounts of possible catalysts, the radiation dose absorbed by the resin and the diameter of the resin column. Current information is not sufficient to define safe upper limits for these parameters. They can be evaluated, however, from equations derived from the Frank-Kamenetskii theory of thermal explosions provided the heat capacities, thermal conductivities and rates of heat evolution in the relevant resin-oxidant mixtures are known. It is recommended that such measurements be made and the appropriate limits be evaluated. A list of additional safety precautions are also presented to aid in the application of these limits and to provide additional margins of safety. In-line evaluation of resin degradation to assess its safety hazard is considered impractical. Rather, it is recommended that the resin be removed from use before it has received the limiting radiation dose, evaluated as described above

Development, design, and preliminary operation of a resin-feed processing facility for resin-based HTGR fuels

International Nuclear Information System (INIS)

Haas, P.A.; Drago, J.P.; Million, D.L.; Spence, R.D.

1978-01-01

Fuel kernels for recycle of 233 U to High-Temperature Gas-Cooled Reactors are prepared by loading carboxylic acid cation exchange resins with uranium and carbonizing at controlled conditions. Resin-feed processing was developed and a facility was designed, installed, and operated to control the kernel size, shape, and composition by processing the resin before adding uranium. The starting materials are commercial cation exchange resins in the sodium form. The size separations are made by vibratory screening of resin slurries in water. After drying in a fluidized bed, the nonspherical particles are separated from spherical particles on vibratory plates of special design. The sized, shape-separated spheres are then rewetted and converted to the hydrogen form. The processing capacity of the equipment tested is equivalent to about 1 kg of uranium per hour and could meet commercial recycle plant requirements without scale-up of the principal process components

Ion Exchange Temperature Testing with SRF Resin - 12088

Energy Technology Data Exchange (ETDEWEB)

Russell, R.L.; Rinehart, D.E.; Brown, G.N.; Peterson, R.A. [Pacific Northwest National Laboratory, Richland, WA 99352 (United States)

2012-07-01

Ion exchange using the Spherical Resorcinol-Formaldehyde (SRF) resin has been selected by the U.S. Department of Energy's Office of River Protection for use in the Pretreatment Facility of the Hanford Tank Waste Treatment and Immobilization Plant (WTP) and for potential application in an at-tank deployment for removing Cs-137. Recent proposed changes to the WTP ion exchange process baseline indicate that higher temperatures (50 deg. C) to alleviate post-filtration precipitation issues prior to reaching the ion exchange columns may be required. Therefore, it is important to understand the behavior of SRF resin performance under the conditions expected with the new equipment and process changes. This research examined the impact of elevated temperature on resin loading and resin degradation during extended solution flow at elevated temperature (45 deg., 50 deg., 55 deg., 60 deg., 65 deg., 75 deg. C). Testing for extended times at elevated temperatures showed that the resin does degrade and loading capacity is reduced at and above 45 deg. C. Above 60 deg. C the resin appears to not load at all. It was observed that the resin disintegrated at 75 deg. C until not much was left and partially disintegrated at 65 deg. C, which caused the column to plug in both tests after ∼336 hours. The results indicate that WTP will lose resin loading capacity if the ion exchange process is performed above 25 deg. C, and the resin will disintegrate above 65 deg. C. Therefore, WTP will have a restricted operating range of temperatures to perform the ion exchange process with this resin. PNNL and WTP are currently evaluating the operating limits of the resin in further detail. Aging in 0.5 M HNO{sub 3} also caused the resin to lose capacity above 25 deg. C and to completely dissolve at 55 deg. C. Again, WTP will have a restricted operating range of temperatures when eluting the resin with nitric acid in order to maintain resin loading capacity and avoid disintegration of the resin

Properties of the Carboxylate ion exchange resins; Karboxylatjonbytarmassans egenskaper

Energy Technology Data Exchange (ETDEWEB)

Allard, Bert; Dario, Maarten [Oerebro Univ. (Sweden); Boren, Hans [Linkoepings Univ. (Sweden); Torstenfelt, Boerje [Swedpower, Stockholm (Sweden); Puigdomenech, Ignasi; Johansson, Claes [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden)

2002-09-01

Weakly acidic, carboxylic resin has been selected, together with strong base anion resins, for water purification at the Forsmark 1 and 2 reactors. For the strong (but not the weak) ion exchange resin the Nuclear Power Inspectorate has given permission to dispose the spent resins in the SFR 1 (the Final Repository for Radioactive Operational Waste). This report gives a review of the carboxylic resins and comes to the conclusion that the resins are very stable and that there should not exist any risks for increased leaching of radionuclides from SFR 1 if these resins are disposed (compared to the strong resins)

Fracture frequency and longevity of fractured resin composite, polyacid-modified resin composite, and resin-modified glass ionomer cement class IV restorations: an up to 14 years of follow-up

DEFF Research Database (Denmark)

van Dijken, Jan W V; Pallesen, Ulla

2010-01-01

The aim of this study was to evaluate the fracture frequency and longevity of fractured class IV resin composite (RC), polyacid-modified resin composite (compomer; PMRC), and resin-modified glass ionomer cement (RMGIC) restorations in a longitudinal long-term follow-up. Eighty-five class IV RC (43...

Commercial Ion Exchange Resin Vitrification in Borosilicate Glass

International Nuclear Information System (INIS)

Cicero-Herman, C.A.; Workman, P.; Poole, K.; Erich, D.; Harden, J.

1998-05-01

Bench-scale studies were performed to determine the feasibility of vitrification treatment of six resins representative of those used in the commercial nuclear industry. Each resin was successfully immobilized using the same proprietary borosilicate glass formulation. Waste loadings varied from 38 to 70 g of resin/100 g of glass produced depending on the particular resin, with volume reductions of 28 percent to 68 percent. The bench-scale results were used to perform a melter demonstration with one of the resins at the Clemson Environmental Technologies Laboratory (CETL). The resin used was a weakly acidic meth acrylic cation exchange resin. The vitrification process utilized represented a approximately 64 percent volume reduction. Glass characterization, radionuclide retention, offgas analyses, and system compatibility results will be discussed in this paper

Anion-exchange resin-based desulfurization process. Final report

Energy Technology Data Exchange (ETDEWEB)

Sheth, A C; Dharmapurikar, R; Strevel, S D

1994-01-01

The following investigations were performed: (1) batch mode screening of eleven(11) commercially available resins and selection of three candidate resins for further evaluation in a fixed-bed setup. (2) Process variables study using three candidate resins in the fixed-bed setup and selection of the ``best`` resin for process economics development. (3) Exhaustion efficiency and solution concentration were found to be inversely related necessitating a trade-off between the resin cost versus the cost of evaporation/concentration of ensuing effluents. (4) Higher concentration of the HCO{sub 3}{sup {minus}} form of active sites over less active CO{sub 3}{sup 2{minus}} form of sites in the resin was believed to be the main reason for the observed increase in the equilibrium capacity of the resin at an elevated static CO{sub 2}-pressure. This Increase in capacity was found to level off around 80--120 psig range. The increase in CO{sub 2}-pressure, however, did not appear to affect the overall ion-exchange kinetics. (5) In the fixed-bed mode, the solution concentration was found to affect the equilibrium capacity of candidate resins. Their relationship was well satisfied by the Langmuir type non-linear equilibrium isotherm. Alternatively, the effect of solution concentration on overall ion-exchange kinetics varied from resin to resin. (6) Product inhibition effect on the resin was observed as an initial increase followed by a significant decrease in the resin`s equilibrium capacity for SO{sub 4}{sup 2{minus}} as the HCO{sub 3}{sup {minus}}/SO{sub 4}{sup 2{minus}} molar ratio in the solution was increased from 0 to 1.0. This ratio, however, did not affect the overall ion-exchange kinetics.

Sequestration Resins for Accelerating Removal of Radioactive Contaminants

International Nuclear Information System (INIS)

Frattini, Paul-L.; Wells, Daniel-M.; Garcia, Susan-E.; Richard, Kohlmann; Asay, Roger; Yengoyan, Leon

2012-09-01

The Electric Power Research Institute (EPRI) is developing sequestration resins that can be used in the treatment of nuclear plant water streams for the enhanced removal of ionic cobalt. EPRI is focusing on three key areas of success: 1. Plant safety. The resins that are synthesized must be fully tested to determine that no leachable species or decomposition products (in the event of a resin bed failure) would be introduced to the plant. 2. Acceptable system performance. The resins are currently being synthesized in a powdered form for use in the reactor water clean-up and fuel pool clean-up systems that utilize pre-coatable filter elements. The resins must have effective flocking behavior; uniform application over the underlay resin and efficient removal from the septa elements after use. Bead type resins are also under development. 3. Enhanced cobalt removal. The resins are expected to out-perform the currently used ion exchange resins in the removal of ionic cobalt. During nuclear plant maintenance or refueling outages, current ion exchange resins may require several days to reduce concentrations of cobalt (for example, radio-cobalt 60 Co and 58 Co) and other activated corrosion products to safe levels in reactor coolant streams. This performance limitation often delays key maintenance activities. EPRI's resins are expected to provide at least a three-fold increase in removal capacity in light water reactor coolants. These resins also offer the potential for higher overall removal efficiencies reducing occupational exposures and waste management costs. This paper addresses issues from the range of novel resin development for radio-cobalt removal from synthesis at the bench-top level through scale-up to demonstration of use in an actual operating nuclear power plant. (authors)

Mechanism for transporting used resin

International Nuclear Information System (INIS)

Sugimoto, Yoshikazu; Yusa, Hideo; Kamiya, Kunio.

1975-01-01

Object: In the operation of a light water reactor type atomic power plant, to permit transport and reuse of used ion exchange resin used for the filtering or cleaning of cooling water or the desalting of radioactive exhaust liquid through an ejector. Structure: Used ion exchange resin within a desalter having high radioactivity is withdrawn through the action of an ejector and led to a solid-liquid separator for separation into used resin and water. The separated resin is directly collected in a storage tank while the separated water is forced through a circulating pump to a gas-liquid separator for separation into gas having radioactivity and water. The separated gas is led to a radioactive gas treatment station while the water deprived of the gas is recirculated by a drive water pump for repeated use. (Kamimura, M.)

Mechanism for transporting used resin

Energy Technology Data Exchange (ETDEWEB)

Sugimoto, Y; Yusa, H; Kamiya, K

1975-01-16

In the operation of a light water reactor type atomic power plant the objectives is to permit transport and reuse of used ion exchange resin used for the filtering or cleaning of cooling water or the desalting of radioactive exhaust liquid through an ejector. Used ion exchange resin within a desalter having high radioactivity is withdrawn through the action of an ejector and led to a solid-liquid separator for separation into used resin and water. The separated resin is directly collected in a storage tank while the separated water is forced through a circulating pump to a gas-liquid separator for separation into gas having radioactivity and water. The separated gas is led to a radioactive gas treatment station while the water deprived of the gas is recirculated by a drive water pump for repeated use.

Dendrochronologically dated pine stumps document phase-wise bog expansion at a northwest German site between ca. 6700 and ca. 3400 BC

Science.gov (United States)

Maike Achterberg, Inke Elisabeth; Eckstein, Jan; Birkholz, Bernhard; Bauerochse, Andreas; Leuschner, Hanns Hubert

2018-01-01

The investigated northwest German mire site at Totes Moor is densely covered with subfossil pine stumps (Pinus sylvestris L.) from the fen-bog transition. This facilitates the spatio-temporal reconstruction of mire development, which is based on 212 in situ tree stumps in the case study presented here. Six dendrochronologically dated site chronologies together cover 2345 years between 6703 and 3403 BC. The gaps in between are 6 to 550 years long. Additionally, a floating chronology of 309 years, containing 30 trees, was radiocarbon-dated to the beginning of the 7th millennium cal BC. Peat-stratigraphical survey was carried out additionally, and elevations a.s.l. were determined at several locations. Tree dying-off phases, which indicate water level rise at the site, mostly in context of the local fen-bog transition, are evident for ca. 6600-6450, ca. 6350-5750, ca. 5300-4900, ca. 4700-4550, ca. 3900-3850, ca. 3700-3600, ca. 3500-3450 and ca. 3400 BC. The spatial distribution of the dated in situ trees illustrates the phase-wise expansion of raised bog over fen peat at the site. The documented bog expansion pulses likely correspond to climatic wet sifts.

Urea-formaldehyde resins: production, application, and testing

Science.gov (United States)

Nuryawan, A.; Risnasari, I.; Sucipto, T.; Heri Iswanto, A.; Rosmala Dewi, R.

2017-07-01

Urea-formaldehyde (UF) resin, one of the most important formaldehyde resin adhesives, is a polymeric condensation product of formaldehyde with urea, and being widely used for the manufacture of wood-based composite panels, such as plywood, particleboard, and fiberboard. In spite of its benefits such as fast curing, good performance in the panels (colorless), and lower cost; formaldehyde emission (FE) originated from either UF resin itself or composite products bonded by UF resins is considered a critical drawback as it affects human health particularly in indoor environment. In order to reduce the FE, lowering formaldehyde/urea (F/U) mole ratio in the synthesis of the UF resin was done. In this study, synthesis of UF resins was carried out following the conventional alkaline-acid two-step reaction with a second addition of urea, resulting in F/U mole ratio around 1.0, namely 0.95; 1.05, and 1.15. The UF resins produced were used as binder for particleboard making. The board was manufactured in the laboratory using shaving type particle of Gmelina wood, 8% UF resin based on oven dry particle, and 1% NH4Cl (20%wt) as hardener for the resin. The target of the thickness was 10 mm and the dimension was 25 cm x 25 cm. The resulted particleboard then was evaluated the physical and the mechanical properties by Japanese Industrial Standard (JIS) A 5908 (2003). Further, the resulted particleboard also was used for the mice cage’s wall in order to mimic the real living environment. After four weeks exposure in the cages, the mice then were evaluated their mucous organs as well as their blood. The experiment results were as follows: 1) It was possible to synthesis UF resins with low F/U mole ratio; 2) However, the particleboard bonded UF resins with low F/U mole ratio showed poor properties, particularly on the thickness swelling and modulus of elasticity; 3) There was no significant differences among the mucous organs of the mice after a month exposure FE originated from

Alumbrado público en Puebla y Tlaxcala y deterioro ambiental en los bosques de La Malintzi, 1820-1870.

Directory of Open Access Journals (Sweden)

José Juan Juárez Flores.

2005-07-01

Full Text Available Tis article analyzes the environmental deterioration of forest resources resulting from the introduction of technical innovations in street lighting in the mid-19th century. It shows how, in the 1850s, the growing use of turpentine, obtained by distilling the natural resin secreted by some tree species, replaced the burning of animal fats and oils in street lamps. Tis change had a damaging impact on the forests of the volcano La Malintzi, which towers above the two cities.

Chemoviscosity modeling for thermosetting resins, 2

Science.gov (United States)

Hou, T. H.

1985-01-01

A new analytical model for simulating chemoviscosity of thermosetting resin was formulated. The model is developed by modifying the Williams-Landel-Ferry (WLF) theory in polymer rheology for thermoplastic materials. By assuming a linear relationship between the glass transition temperature and the degree of cure of the resin system under cure, the WLF theory can be modified to account for the factor of reaction time. Temperature dependent functions of the modified WLF theory constants were determined from the isothermal cure data of Lee, Loos, and Springer for the Hercules 3501-6 resin system. Theoretical predictions of the model for the resin under dynamic heating cure cycles were shown to compare favorably with the experimental data reported by Carpenter. A chemoviscosity model which is capable of not only describing viscosity profiles accurately under various cure cycles, but also correlating viscosity data to the changes of physical properties associated with the structural transformations of the thermosetting resin systems during cure was established.

Mercuric iodide semiconductor detectors encapsulated in polymeric resin

Energy Technology Data Exchange (ETDEWEB)

Martins, Joao F. Trencher; Santos, Robinson A. dos; Ferraz, Caue de M.; Oliveira, Adriano S.; Velo, Alexandre F.; Mesquita, Carlos H. de; Hamada, Margarida M., E-mail: mmhamada@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil); Disch, Christian; Fiederle, Michael [Albert-Ludwigs Universität Freiburg - UniFreibrug, Freiburg Materials Research Center - FMF, Freiburg (Germany)

2015-07-01

The development of new semiconductor radiation detectors always finds many setback factors, such as: high concentration of impurities in the start materials, poor long term stability, the surface oxidation and other difficulties discussed extensively in the literature, that limit their use. In this work was studied, the application of a coating resin on HgI2 detectors, in order to protect the semiconductor crystal reactions from atmospheric gases and to isolate electrically the surface of the crystals. Four polymeric resins were analyzed: Resin 1: 50% - 100%Heptane, 10% - 25% methylcyclohexane, <1% cyclohexane; Resin 2: 25% - 50% ethanol, 25% - 50% acetone, <2,5% ethylacetate; Resin 3: 50% - 100% methylacetate, 5% - 10% n-butylacetate; Resin 4: 50% - 100% ethyl-2-cyanacrylat. The influence of the polymeric resin type used on the spectroscopic performance of the HgI{sub 2} semiconductor detector is, clearly, demonstrated. The better result was found for the detector encapsulated with Resin 3. An increase of up to 26 times at the stability time was observed for the detectors encapsulated compared to that non-encapsulated detector. (author)

Fiber reinforced silicon-containing arylacetylene resin composites

Directory of Open Access Journals (Sweden)

2007-12-01

Full Text Available A silicon-containing arylacetylene resin (SAR, a poly(dimethylsilyleneethynylene phenyleneethynylene (PMSEPE, was synthesized. The PMSEPE is a solid resin at ambient temperature with a softening temperature about 60°C and soluble in some solvents like tetrahydrofuran. The melt viscosity of the PMSEPE resin is less than 1 Pa•s. The resin could cure at the temperature of lower than 200°C. Fiber reinforced PMSEPE composites were prepared from prepregs which were made by the impregnation of fibers in PMSEPE resin solution. The composites exhibit good mechanical properties at room temperature and 250°C. The observation on fracture surfaces of the composites reinforced by glass fibers and carbon fibers demonstrates that the adhesion between the fibers and resin is good. The results from an oxyacetylene flame test show that the composites have good ablation performance and XRD analyses indicate that SiC forms in the residues during the ablation of the composites.

Cleanup of TMI-2 demineralizer resins

International Nuclear Information System (INIS)

Bond, W.D.; King, L.J.; Knauer, J.B.; Hofstetter, K.J.; Thompson, J.D.

1985-01-01

Radiocesium is being removed from Demineralizers A and B (DA and DB by a process that was developed from laboratory tests on small samples of resin from the demineralizers. The process was designed to elute the radiocesium from the demineralizer resins and then to resorb it onto the zeolite ion exchangers contained in the Submerged Demineralizer System (SDS). The process was also required to limit the maximum cesium activities in the resin eluates (SDS feeds) so that the radiation field surrounding the pipelines would not be excessive. The process consists of 17 stages of batch elution. In the initial stage, the resin is contacted with 0.18 M boric acid. Subsequent stages subject the resin to increasing concentrations of sodium in NaH 2 BO 3 -H 3 BO 3 solution (total B = 0.35 M) and then 1 M sodium hydroxide in the final stages. Results on the performance of the process in the cleanup of the demineralizers at TMI-2 are compared to those obtained from laboratory tests with small samples of the DA and DB resins. To date, 15 stages of batch elution have been completed on the demineralizers at TMI-2 which resulted in the removal of about 750 Ci of radiocesium from DA and about 3300 Ci from DB

Embedding of reactor wastes in plastic resins

International Nuclear Information System (INIS)

1979-01-01

STEAG Kernenergie GmbH is so far the only firm commercially to condition radioactive bead ion exchange resins by embedding in polystyrene resins. The objective of the work reported here was to study and develop methods for immobilization of other reactor wastes in plastic resins. Comparison studies on high quality cement however showed favourable results for cement with respect to process safety and economy. For this reason STEAG interrupted its work in the field of resin embedding after about one year. The work carried out during this period is surveyed in this report, which includes a comprehensive literature study on reactor wastes and their solidification in plastic resins as well as on regulations with regard to radioactive waste disposal in the member states of the European Communities

Method for detecting resin leakage in LWR coolant

International Nuclear Information System (INIS)

Girard, J.E.

1988-05-01

Resin leakage from condensate polishing units can result in steam generator corrosion. This report describes the development of a resin leakage detection method based in analyzing the organic breakdown products released from resin on heating. The breakdown products are analyzed using high performance liquid chromatography (HPLC) with fluorescence detection. Some of the organic products formed have been identified. A design for a resin monitoring unit, suitable for incorporation into the IONTRAC system, is presented. Theoretically, detection of ppB levels of resin by processing about one liter of water, is possible

Effect of repair resin type and surface treatment on the repair strength of heat-polymerized denture base resin.

Science.gov (United States)

Alkurt, Murat; Yeşil Duymuş, Zeynep; Gundogdu, Mustafa

2014-01-01

Acrylic resin denture fracture is common in prosthodontic practice. When fractured denture bases are repaired, recurrent fractures frequently occur at the repair surface interface or adjacent areas. The purpose of this study was to evaluate the effect of different surface treatments on the flexural strength of the acrylic resin denture base repaired with heat-polymerized acrylic resin, autopolymerizing resin, and light-polymerized acrylic resin. Ninety-six specimens of heat-polymerized acrylic resin were prepared according to the American Dental Association Specification No. 12 (65.0 × 10.0 × 2.5 mm) and sectioned into halves to create a repair gap (3.0 × 10 × 2.5 mm). The sectioned specimens were divided into 3 groups according to their repair materials. The specimens from each group were divided into 4 subgroups according to their surface treatments: a control group without any surface treatment; an experimental group treated with methyl methacrylate monomer (MMA group); an experimental group treated with airborne-particle abrasion with aluminum oxide particles of 250-μm particle size (abrasion group); and an experimental group treated with erbium:yttrium-aluminum-garnet laser (laser group). After the surface treatments, the 3 materials were placed into the repair gaps and then polymerized. After all of the specimens had been ground and polished, they were stored in distilled water at 37°C for 1 week and subjected to a 3-point bend test. Data were analyzed with a 2-way analysis of variance, and the Tukey honestly significant difference test was performed to identify significant differences (α=.05). The effects of the surface treatments and repair resins on the surface of the denture base resin were examined with scanning electron microscopy. Significant differences were found among the groups in terms of repair resin type (P<.001). All surface-treated specimens had higher flexural strength than controls, except the surface treated with the methyl

21 CFR 177.2430 - Polyether resins, chlorinated.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Polyether resins, chlorinated. 177.2430 Section 177... Components of Articles Intended for Repeated Use § 177.2430 Polyether resins, chlorinated. Chlorinated polyether resins may be safely used as articles or components of articles intended for repeated use in...

Volumetric polymerization shrinkage of contemporary composite resins

Directory of Open Access Journals (Sweden)

Halim Nagem Filho

2007-10-01

Full Text Available The polymerization shrinkage of composite resins may affect negatively the clinical outcome of the restoration. Extensive research has been carried out to develop new formulations of composite resins in order to provide good handling characteristics and some dimensional stability during polymerization. The purpose of this study was to analyze, in vitro, the magnitude of the volumetric polymerization shrinkage of 7 contemporary composite resins (Definite, Suprafill, SureFil, Filtek Z250, Fill Magic, Alert, and Solitaire to determine whether there are differences among these materials. The tests were conducted with precision of 0.1 mg. The volumetric shrinkage was measured by hydrostatic weighing before and after polymerization and calculated by known mathematical equations. One-way ANOVA (a or = 0.05 was used to determine statistically significant differences in volumetric shrinkage among the tested composite resins. Suprafill (1.87±0.01 and Definite (1.89±0.01 shrank significantly less than the other composite resins. SureFil (2.01±0.06, Filtek Z250 (1.99±0.03, and Fill Magic (2.02±0.02 presented intermediate levels of polymerization shrinkage. Alert and Solitaire presented the highest degree of polymerization shrinkage. Knowing the polymerization shrinkage rates of the commercially available composite resins, the dentist would be able to choose between using composite resins with lower polymerization shrinkage rates or adopting technical or operational procedures to minimize the adverse effects deriving from resin contraction during light-activation.

Chemoviscosity modeling for thermosetting resins

Science.gov (United States)

Tiwari, S. N.; Hou, T. H.; Bai, J. M.

1985-01-01

A chemoviscosity model, which describes viscosity rise profiles accurately under various cure cycles, and correlates viscosity data to the changes of physical properties associated with structural transformations of the thermosetting resin system during cure, was established. Work completed on chemoviscosity modeling for thermosetting resins is reported.

Shear bond strength evaluation of resin composite to resin-modified glass-ionomer cement using three different resin adhesives vs. glass-ionomer based adhesive

Directory of Open Access Journals (Sweden)

Mostafa Sadeghi

2015-12-01

Full Text Available Background: The clinical success of sandwich technique depends on the strength of resin-modified glass ionomer cement (RMGIC bonding to both dentin and resin composite. Therefore, the shear bond strength (SBS of resin composite bonded to RMGIC utilizing different resin adhesives versus a GIC-based adhesive was compared. Materials and methods: In this in vitro study, 84 holes (5×2 mm were prepared in acrylic blocks, randomly divided into seven groups (n=12 and filled with RMGIC (Light-Cured Universal Restorative, GC. In the Group I; no adhesive was applied on the RMGIC. In the Group II, non-etched and Group III was etched with phosphoric acid. In groups II and III, after rinsing, etch-and-rinse adhesive (OptiBond Solo Plus; in the Group IV; a two-step self-etch adhesive (OptiBond XTR and in Group V; a one-step self-etch (OptiBond All-in-One were applied on the cement surfaces. Group VI; a GIC-based adhesive (Fuji Bond LC was painted over the cement surface and cured. Group VII; the GIC-based adhesive was brushed over RMGIC followed by the placement of resin composite and co-cured. Afterward; resin composite (Point 4 cylinders were placed on the treated cement surfaces. The specimens were placed in 100% humidity at 37 ± 1°C and thermo cycled. The shear bond test was performed at a cross-head speed of 1 mm/min and calculated in MPa; the specimens were examined to determine mode of failure. The results were analyzed using one-way ANOVA and Tukey test. Results: The maximum (24.62±3.70 MPa and minimum (18.15±3.38 MPa SBS mean values were recorded for OptiBond XTR adhesive and the control group, respectively. The pairwise comparisons showed no significant differences between the groups that bonded with different adhesives. The adhesive failure was the most common failure mode observed. Conclusion: This study suggests that GIC-based adhesive could be applied over RMGIC as co-cure technique for sandwich restorations in lieu of employing the resin

Characterization of monolith block of spent resin cementation

International Nuclear Information System (INIS)

Prayitno; Endro-Kismolo; Isman MT

1996-01-01

Spent resin immobilization process with cement was done to prevent release of radionuclide in the ultimate storage or disposal. The varied Composition of water/cement ratio in the cementation process were 0.3; 0.4; 0.5 and the various weight of resin waste are 25 g, 37.5 g and 50 gram. The compressive strength of the various water/cement ratio without spent resin was bigger than 0.3. This investigation proved that the compressive strength of Tiga Roda cement was bigger than those of Gresik cement or Nusantara cement. The compressive of the cement block of were the spent resin cementation was influenced by the water/cement ratio and the total spent resin addition. The best condition reached at the water/cement ratio of 0.3 and 25 gram spent resin, was compressive strength of 17.86 N/mm 2 . Leaching rate of the various weight composition of spent resin cementation for 91 days were between 10 -2 - 10 -4 gram.cm -2 .day -1

Phosphorus-containing imide resins - Modification by elastomers

Science.gov (United States)

Varma, I. K.; Fohlen, G. M.; Parker, J. A.; Varma, D. S.

1984-01-01

The syntheses and general features of addition-type maleimide resins based on bis(m-aminophenyl)phosphine oxide and tris(m-aminophenyl)phosphine oxide have been reported previously. These resins have been used to fabricate graphite cloth laminates having excellent flame resistance. These composites did not burn even in pure oxygen. However, these resins were somewhat brittle. This paper reports the modification of these phosphorus-containing resins by an amine-terminated butadiene-acrylonitrile copolymer (ATBN) and a perfluoroalkylene diaromatic amine elastomer (3F). An approximately two-fold increase in short beam shear strength and flexural strength was observed at 7 percent ATBN concentration. The tensile, flexural, and shear strengths were reduced when 18 percent ATBN was used. Anaerobic char yields of the resins at 800 C and the limiting oxygen indexes of the laminates decreased with increasing ATBN concentration. The perfluorodiamine (3F) was used with both imide resins at 6.4 percent concentration. The shear strength was doubled in the case of the bisimide with no loss of flammability characteristics. The modified trisimide laminate also had improved properties over the unmodified one. The dynamic mechanical analysis of a four-ply laminate indicated a glass transition temperature above 300 C. Scanning electron micrographs of the ATBN modified imide resins were also recorded.

Method of removing contaminants from plastic resins

Science.gov (United States)

Bohnert, George W.; Hand, Thomas E.; DeLaurentiis, Gary M.

2008-11-18

A method for removing contaminants from synthetic resin material containers using a first organic solvent system and a second carbon dioxide system. The organic solvent is utilized for removing the contaminants from the synthetic resin material and the carbon dioxide is used to separate any residual organic solvent from the synthetic resin material.

Method for removing contaminants from plastic resin

Science.gov (United States)

Bohnert, George W.; Hand, Thomas E.; DeLaurentiis, Gary M.

2008-12-30

A method for removing contaminants from synthetic resin material containers using a first organic solvent system and a second carbon dioxide system. The organic solvent is utilized for removing the contaminants from the synthetic resin material and the carbon dioxide is used to separate any residual organic solvent from the synthetic resin material.

Transformasi α-Pinena dengan Bakteri Pseudomonas aeruginosa ATCC 25923

Directory of Open Access Journals (Sweden)

Nanik Wijayati

2014-03-01

Full Text Available Indonesia adalah Negara utama yang memproduksi minyak atsiri di dunia. Minyak terpentin adalah minyak atsiri yang dihasilkan dari destilasi getah pinus Pinus merkusi J ungh. Et. De. Vr. Tujuan penelitian ini adalah untuk meningkatkan nilai minyak terpentin dengan mengubah kandungan utamanya, α-pinena menjadi senyawa baru menggunakan P. Aeruginosa dalam metode mikrobiologi. Minyak terpentin diambil dari Perhutani Laboratorium Jawa Tengah, dibuat dengan seri konsentrasi 0,5%, 1%, 2%, dan 4%. Minyak terpentin diinokulasi dalam suspensi P. areuginosa selama 48 jam pada suhu kamar (25-28oC. Hasilnya diekstraksi menggunakan dietil eter. Filtrat Terpentin dianalisis menggunakan GCdan IR. Hasil analisis GC menunjukkan puncak baru di konsentrasi 0,5%, 1%, dan 2%, tetapi dalam konsentrasi 4% tidak menunjukkan puncak baru. Hasil IR menunjukkan hidroksil (OH- dan C-O alkohol. Berdasarkan penelitian ini, dapat disimpulkan bahwa minyak terpentin dapat ditransformasi untuk menjadi senyawa yang mengandung gugus-OH melalui metode mikrobiologi dengan menggunakan bakteri P. aeruginosa. Indonesia is the main producer of essential oil in the world. Turpentine oil is an essential oil which is obtained from pine resin distillation of Pinus merkusi Jungh. et. De.Vr. The aim of this experiment was to increase the value of turpentine oil by changing its main content, i.e. α-pinene, into a new compound using P. aeruginosa in microbiological method. Turpentine oil was collected from Perhutani Central Java Laboratory, and was made into 0.5%; 1%; 2%; and 4% concentrations and it was inoculated in P. areuginosa suspension for 48 hours in room temperature (25°C-280C. The result was extracted using diethylether. The filtrate of turpentine was analyzed using GC and IR. The GC analysis result showed a new peak in 0.5%; 1%; and 2% concentrations, but in the 4% concentration didn’t show a new peak. The IR result showed alcohol with hydroxyl (-OH and –C–O groups. This

Cure shrinkage in casting resins

Energy Technology Data Exchange (ETDEWEB)

Spencer, J. Brock [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2015-02-01

A method is described whereby the shrinkage of a casting resin can be determined. Values for the shrinkage of several resin systems in frequent use by Sandia have been measured. A discussion of possible methods for determining the stresses generated by cure shrinkage and thermal contraction is also included.

Resin Poliester Tak Jenuh Untuk Imobilisasi Resin Bekas Pengolahan Simulasi Limbah Radioaktif Cair

Directory of Open Access Journals (Sweden)

Herlan Martono

2017-03-01

Full Text Available Telah dilakukan penelitian tentang imobilisasi resin bekas pengolah limbah trans-uranium denganresin poliester tak jenuh untuk mengetahui kualitas blok polimer-limbah sebagai fungsi kandunganlimbah. Polimerisasi dilakukan dengan mencampurkan resin poliester tak jenuh dengan katalisdengan perbandingan katalis 1% dari jumlah resin poliester tak jenuh yang digunakan, kemudianditambahkan limbah cair transuranium simulasi. blok polimer-limbah yang terjadi diukur densitas,kuat tekan dengan alat Paul Weber, dan laju pelindihan dengan alat soxhlet pada 100 0C dan 1 atmselama 6 jam. Blok polimer dibuat dengan kandungan limbah 10, 20, 30, 40, dan 50 % berat. Hasilpenelitian menunjukkan bahwa semakin besar kandungan limbah maka kuat tekan blok polimerlimbahsemakin kecil, sedangkan laju pelindihannya semakin besar. Berdasarkan kuat tekan dan lajupelindihan, maka hasil terbaik diperoleh untuk blok-polimer dengan kandungan limbah 20 % dan 30%.

Modification of Aliphatic Petroleum Resin by Peracetic Acid

OpenAIRE

Bondaletov, Vladimir Grigoryevich; Bondaletova, Lyudmila Ivanovna; Hamlenko, A.; Bondaletov, Oleg Vladimirovich; Starovoit, M.

2014-01-01

This work demonstrates the possibility of obtaining modified aliphatic resin (PRC5) by means of petroleum resin oxidation by peracetic acid. We have experimentally determined oxidation conditions that lead to producing resin with maximum epoxy and acid numbers. Ratio of "oxidative system: PRC5" is 0.5:1, process duration is 2 hours. The modified resin structure is determined by IR and NMR spectroscopy.

Solidifying power station resins and sludges

International Nuclear Information System (INIS)

Willis, A.S.D.; Haigh, C.P.

1984-01-01

Radioactive ion exchange resins and sludges arise at nuclear power stations from various operations associated with effluent treatment and liquid waste management. As the result of an intensive development programme, the Central Electricity Generating Board (CEGB) has designed a process to convert power station resins and sludges into a shielded, packaged solid monolithic form suitable for final disposal. Research and development, the generic CEGB sludge/resin conditioning plant and the CEGB Active Waste Project are described. (U.K.)

Monoterpene composition of pine species and hybrids...some preliminary findings

Science.gov (United States)

Richard H. Smith

1967-01-01

Xylem resin samples, obtained from 72 freshly cut pine stumps at the Institute of Forest Genetics, Placerville, Calif., were analyzed for monoterpenes by gasliquid chromatography. Very little or no qualitative or quantitative variation could be attributed to annual ring, time of securing sample, and period of storage of sample up to 1 year. The 34 hybrids sampled...

Incineration of ion exchange resins using concentric burners

International Nuclear Information System (INIS)

Fukasawa, T.; Chino, K.; Kawamura, F.; Kuriyama, O.; Yusa, H.

1985-01-01

A new incineration method, using concentric burners, is studied to reduce the volume of spent ion exchange resins generated from nuclear power plants. Resins are ejected into the center of a propane-oxygen flame and burned within it. The flame length is theoretically evaluated by the diffusion-dominant model. By reforming the burner shape, flame length can be reduced by one-half. The decomposition ratio decreases with larger resin diameters due to the loss of unburned resin from the flame. A flame guide tube is adapted to increase resin holding time in the flame, which improves the decomposition ratio to over 98 wt%

Incineration of ion-exchange resins

International Nuclear Information System (INIS)

Valkiainen, M.; Nykyri, M.

1985-01-01

Incineration of ion-exchange resins in a fluidized bed was studied on a pilot plant scale at the Technical Research Centre of Finland. Both granular and powdered resins were incinerated in dry and slurry form. Different bed materials were used in order to trap as much cesium and cobalt (inactive tracers) as possible in the bed. Also the sintering of the bed materials was studied in the presence of sodium. When immobilized with cement the volume of ash-concrete is 4 to 22% of the concrete of equal compressive strength acquired by direct solidification. Two examples of multi-purpose equipment capable of incinerating ion-exchange resins are presented. (orig.)

[Acrylic resin removable partial dentures

NARCIS (Netherlands)

Baat, C. de; Witter, D.J.; Creugers, N.H.J.

2011-01-01

An acrylic resin removable partial denture is distinguished from other types of removable partial dentures by an all-acrylic resin base which is, in principle, solely supported by the edentulous regions of the tooth arch and in the maxilla also by the hard palate. When compared to the other types of

Bond strength of resin-resin interfaces contaminated with saliva and submitted to different surface treatments

DEFF Research Database (Denmark)

Furuse, Adilson Yoshio; da Cunha, Leonardo Fernandes; Benetti, Ana Raquel

2007-01-01

of silane and adhesive system. Resin cylinders were placed over the treated surfaces. The specimens were stored in water or ethanol. Shear bond strength tests were performed and the mode of failure was evaluated. Data were submitted to two-way ANOVA and Dunnett T3 test. Contamination of resin...

PILOT-SCALE HYDRAULIC TESTING OF RESORCINOL FORMALDEHYDE ION EXCHANGE RESIN

International Nuclear Information System (INIS)

Adamson, D

2007-01-01

Savannah River National Laboratory (SRNL) performed pilot-scale hydraulic/chemical testing of spherical resorcinol formaldehyde (RF) ion exchange (IX) resin for the River Protection Project Hanford Tank Waste Treatment and Immobilization Plant (WTP) Project. The RF resin cycle testing was conducted in two pilot-scale IX columns, 1/4 and 1/2 scale. A total of twenty-three hydraulic/chemical cycles were successfully completed on the spherical RF resin. Seven of the cycles were completed in the 12-inch IX Column and sixteen cycles were completed in the 24-inch IX Column. Hydraulic testing showed that the permeability of the RF resin remained essentially constant, with no observed trend in the reduction of the permeability as the number of cycles increased. The permeability during the pilot-scale testing was 2 1/2 times better than the design requirements of the WTP full-scale system. The permeability of the resin bed was uniform with respect to changes in bed depth. Upflow Regeneration and Simulant Introduction in the IX columns revealed another RF resin benefit; negligible radial pressures to the column walls from the swelling of resin beads. In downflow of the Regeneration and Simulant Introduction steps, the resin bed particles pack tightly together and produce higher hydraulic pressures than that found in upflow. Also, upflow Simulant Introduction produced an ideal level bed for the twenty cycles completed using upflow Simulant Introduction. Conversely, the three cycles conducted using downflow Simulant Introduction produced an uneven bed surface with erosion around the thermowells. The RF resin bed in both columns showed no tendency to form fissures or pack more densely as the number of cycles increased. Particle size measurements of the RF resin showed no indication of particle size change (for a given chemical) with cycles and essentially no fines formation. Micrographs comparing representative bead samples before and after testing indicated no change in bead

PILOT-SCALE HYDRAULIC TESTING OF RESORCINOL FORMALDEHYDE ION EXCHANGE RESIN

Energy Technology Data Exchange (ETDEWEB)

Adamson, D

2007-01-09

Savannah River National Laboratory (SRNL) performed pilot-scale hydraulic/chemical testing of spherical resorcinol formaldehyde (RF) ion exchange (IX) resin for the River Protection Project Hanford Tank Waste Treatment & Immobilization Plant (WTP) Project. The RF resin cycle testing was conducted in two pilot-scale IX columns, 1/4 and 1/2 scale. A total of twenty-three hydraulic/chemical cycles were successfully completed on the spherical RF resin. Seven of the cycles were completed in the 12-inch IX Column and sixteen cycles were completed in the 24-inch IX Column. Hydraulic testing showed that the permeability of the RF resin remained essentially constant, with no observed trend in the reduction of the permeability as the number of cycles increased. The permeability during the pilot-scale testing was 2 1/2 times better than the design requirements of the WTP full-scale system. The permeability of the resin bed was uniform with respect to changes in bed depth. Upflow Regeneration and Simulant Introduction in the IX columns revealed another RF resin benefit; negligible radial pressures to the column walls from the swelling of resin beads. In downflow of the Regeneration and Simulant Introduction steps, the resin bed particles pack tightly together and produce higher hydraulic pressures than that found in upflow. Also, upflow Simulant Introduction produced an ideal level bed for the twenty cycles completed using upflow Simulant Introduction. Conversely, the three cycles conducted using downflow Simulant Introduction produced an uneven bed surface with erosion around the thermowells. The RF resin bed in both columns showed no tendency to form fissures or pack more densely as the number of cycles increased. Particle size measurements of the RF resin showed no indication of particle size change (for a given chemical) with cycles and essentially no fines formation. Micrographs comparing representative bead samples before and after testing indicated no change in bead

PILOT-SCALE HYDRAULIC TESTING OF RESORCINOL FORMALDEHYDE ION EXCHANGE RESIN

Energy Technology Data Exchange (ETDEWEB)

Adamson, D

2006-11-08

Savannah River National Laboratory (SRNL) performed pilot-scale hydraulic/chemical testing of spherical resorcinol formaldehyde (RF) ion exchange (IX) resin for the River Protection Project-Hanford Tank Waste Treatment & Immobilization Plant (WTP) Project. The RF resin cycle testing was conducted in two pilot-scale IX columns, 1/4 and 1/2 scale. A total of twenty-three hydraulic/chemical cycles were successfully completed on the spherical RF resin. Seven of the cycles were completed in the 12 inch IX Column and sixteen cycles were completed in the 24 inch IX Column. Hydraulic testing showed that the permeability of the RF resin remained essentially constant, with no observed trend in the reduction of the permeability as the number of cycles increased. The permeability during the pilot-scale testing was 2 1/2 times better than the design requirements of the WTP full-scale system. The permeability of the resin bed was uniform with respect to changes in bed depth. Upflow Regeneration and Simulant Introduction in the IX columns revealed another RF resin benefit; negligible radial pressures to the column walls from the swelling of resin beads. In downflow of the Regeneration and Simulant Introduction steps, the resin bed particles pack tightly together and produce higher hydraulic pressures than that found in upflow. Also, upflow Simulant Introduction produced an ideal level bed for the twenty cycles completed using upflow Simulant Introduction. Conversely, the three cycles conducted using downflow Simulant Introduction produced an uneven bed surface with erosion around the thermowells. The RF resin bed in both columns showed no tendency to form fissures or pack more densely as the number of cycles increased. Particle size measurements of the RF resin showed no indication of particle size change (for a given chemical) with cycles and essentially no fines formation. Micrographs comparing representative bead samples before and after testing indicated no change in bead

Pyovagina and stump pyometra in a neutered XX sex-reversed Beagle: a case report

International Nuclear Information System (INIS)

Williams, J.; Partington, B.P.; Smith, B.; Hedlund, C.S.; Law, J.M.

1997-01-01

An 18-month-old, neutered male beagle presented with acute abdominal signs and a suppurative infection of the urogenital tract. Chromosomal sex was female (78, XX), gonadal sex was male (testicles), and phenotypic sex was ambiguous, with evidence of both male and female duct systems. The internal and external genitalia consisted of epididymides, an underdeveloped uterus with an immature spermatic cord, communication between the uterus or cranial vagina and the membranous urethra, a urethrographically male urethra, a hypoplastic os penis, and a hypoplastic penis with hypospadia. Based on these findings and the familial history of a similarly affected litter mate, the dog was diagnosed as having the XX male syndrome with pyovagina and uterine stump pyometra. Radiographic and ultrasonographic investigations are described, and abnormalities of chromosomal sex, gonadal sex, and phenotypic sex are discussed

The absorption of plutonium by anion resins

Energy Technology Data Exchange (ETDEWEB)

Durham, R. W.; Mills, R.

1961-10-15

Equilibrium experiments have shown Pu{sup +4} to be absorbed from nitric acid onto an anion resin as a complex anion Pu(NO{sub 3}){sub 6}{sup -2}. The amount of absorption is dependent on the plutonium and nitric acid concentrations in the equilibrium solution with a maximum at 7N to 8N HNO{sub 3}. A low cross-linked resin has a higher capacity and reaches equilibrium more rapidly than the normally supplied resin. Saturation capacity of one per cent cross-linked Nalcite SBR (Dowex 1), 50 -- 100 mesh, is 385 mg Pu/gram dry resin. (author)

PEG-related polymer resins as synthetic supports

Institute of Scientific and Technical Information of China (English)

无

2010-01-01

Combinatorial chemistry has become a significant part of the discovery and optimization process for novel drugs,affinity ligands,and catalysts.The polymeric supports play a key role in combinatory chemistry.Therefore,various kinds of functional polymer resins have been exploited as supports,reagents,and catalysts in organic synthesis.In comparison to the conventional Merrifield resins,the poly(ethylene glycol)(PEG)-related polymer resins have advantages including good compatibilities with polar solvents,good solvent absorbency and swelling properties.This review focuses primarily on the more recent work in the field of developing PEG-related polymer resins as supports for organic synthesis.

Color of bulk-fill composite resin restorative materials.

Science.gov (United States)

Barutcigil, Çağatay; Barutcigil, Kubilay; Özarslan, Mehmet Mustafa; Dündar, Ayşe; Yilmaz, Burak

2018-03-01

To evaluate the color stability of novel bulk-fill composite resins. Color measurements of a nanohybrid composite resin (Z550) and 3 bulk-fill composite resins (BLK, AFX, XTF; n = 45) were performed before polymerization. After polymerization, color measurements were repeated and specimens were immersed in distilled water or red wine, or coffee. Color change [CIEDE2000 (ΔE 00 )] was calculated after 24 h, 1 and 3 weeks. Data were analyzed with Kruskal-Wallis, Mann-Whitney U and Wilcoxon tests (α = 0.05). Color changes observed after polymerization were significant for all groups. Color changes observed in distilled water for Z550 and AFX were significant. Color changes after stored in red wine and coffee were significant for all groups. Bulk-fill composite resin color change increased over time for all groups in red wine and coffee (P composite resin and bulk-fill composite resins. AFX had the highest color change in distilled water. The color of tested bulk-fill composite resins significantly changed after immersion in beverages and over time. Color change observed with the nanohybrid composite resin after 1 week was stable. Clinicians should keep in mind that tested composite resins may change color when exposed to water and significantly change color immediately after they are polymerized. In addition, the color change continues over time should the patient is a coffee and/or red wine consumer. © 2017 Wiley Periodicals, Inc.

Application conditions for ester cured alkaline phenolic resin sand

Directory of Open Access Journals (Sweden)

Ren-he Huang

2016-07-01

Full Text Available Five organic esters with different curing speeds: propylene carbonate (i.e. high-speed ester A; 1, 4-butyrolactone; glycerol triacetate (i.e. medium-speed ester B; glycerol diacetate; dibasic ester (DBE (i.e. low-speed ester C, were chosen to react with alkaline phenolic resin to analyze the application conditions of ester cured alkaline phenolic resin. The relationships between the curing performances of the resin (including pH value, gel pH value, gel time of resin solution, heat release rate of the curing reaction and tensile strength of the resin sand and the amount of added organic ester and curing temperature were investigated. The results indicated the following: (1 The optimal added amount of organic ester should be 25wt.%-30wt.% of alkaline phenolic resin and it must be above 20wt.%-50 wt.% of the organic ester hydrolysis amount. (2 High-speed ester A (propylene carbonate has a higher curing speed than 1, 4-butyrolactone, and they were both used as high-speed esters. Glycerol diacetate is not a high-speed ester in alkaline phenolic resin although it was used as a high-speed ester in ester cured sodium silicate sand; glycerol diacetate and glycerol triacetate can be used as medium-speed esters in alkaline phenolic resin. (3 High-speed ester A, medium-speed ester B (glycerol triacetate and low-speed ester C (dibasic ester, i.e., DBE should be used below 15 ìC, 35 ìC and 50 ìC, respectively. High-speed ester A or low-speed ester C should not be used alone but mixed with medium-speed ester B to improve the strength of the resin sand. (4 There should be a suitable solid content (generally 45wt.%-65wt.% of resin, alkali content (generally 10wt.%-15wt.% of resin and viscosity of alkaline phenolic resin (generally 50-300 mPa≤s in the preparation of alkaline phenolic resin. Finally, the technique conditions of alkaline phenolic resin preparation and the application principles of organic ester were discussed.

40 CFR 414.50 - Applicability; description of the thermosetting resins subcategory.

Science.gov (United States)

2010-07-01

... thermosetting resins subcategory. 414.50 Section 414.50 Protection of Environment ENVIRONMENTAL PROTECTION... Thermosetting Resins § 414.50 Applicability; description of the thermosetting resins subcategory. The provisions... the products classified under SIC 28214 thermosetting resins including those resins and resin groups...

Thermosetting resins for nuclear track detection

International Nuclear Information System (INIS)

Fujii, M.

1985-01-01

Several new thermosetting resins with a three dimensional network structure like CR-39 were polymerized to study their characteristics for use as nuclear track detectors. During the course of this study, thermosetting resins with good etching properties and various sensitivities have been obtained. The comparison of the molecular structures of these resins gives up an important clue for the development of highly sensitive polymeric track detectors. They will also be useful for observations of ultra-heavy cosmic rays and heavily ionizing particles at low energies. (orig.)

Thermosetting resins for nuclear track detection

International Nuclear Information System (INIS)

Fujii, Masami; Yokota, Rikio

1985-01-01

Several new thermosetting resins with a three dimensional network structure like CR-39 were polymerized to study their characteristics for use as nuclear track detectors. During the course of this study, thermosetting resins with good etching properties and various sensitivities have been obtained. The comparison of the molecular structures of these resins gives us an important clue for the development of highly sensitive polymeric track detectors. They will also be useful for observations of ultra-heavy cosmic rays and heavily ionizing particles at low energies. (author)

Method of burning ion-exchange resin contaminated with radioactivity

International Nuclear Information System (INIS)

Suzuki, Shigenori.

1986-01-01

Purpose: To process spent ion exchange resins to reduce their volume, without increasing the load on a off-gas system and in a stable state and at the same time not leaving any uncombusted portions. Method: The water slurries of the ion exchange resins contaminated with radioactive materials is dehydrated or dry combusted to reduce the water content. A binder is then added to solidify the ion exchange resin. The solidified ion exchange resins are then combusted in a furnace. This prevents the ion exchange resin from being dispersed by air and combustion gases. Furthermore, the solidified ion exchange resins in the form of small pellets burn from the surface inwards. Moreover the binder is carbonized by the combustion heat and promotes combustion to convert the ion exchange resins into a solid mass, making sure that no uncombusted portion is left. (Takahashi, M.)

Integrating Porous Resins In Enzymatic Processes

DEFF Research Database (Denmark)

Al-Haque, Naweed

. Screening resins for moderately hydrophobic multi-component systems is challenging. Often it is found that the capacity of the resin is inversely related with product selectivity. Therefore a tradeoff has to be made between these parameters which can be crucial from an economic point of view. A low resin...... procedure. The screening therefore becomes a multi-objective task that has to be solved simultaneously. Such an approach has been applied in the method formulated in this framework. To overcome these challenges, different process strategies are required to obtain high yields. A number of different...... inhibition, has gained considerable recognition. The resins act as a reservoir for the inhibitory substrate and a sink for the inhibitory product and simultaneously attain the required high substrate loading to make the process economically feasible. In this way the potential benefit of the enzyme can...

Paramagnetic epoxy resin

Directory of Open Access Journals (Sweden)

E. C. Vazquez Barreiro

2017-01-01

Full Text Available This work illustrates that macrocycles can be used as crosslinking agents for curing epoxy resins, provided that they have appropriate organic functionalities. As macrocycles can complex metal ions in their structure, this curing reaction allows for the introduction of that metal ion into the resin network. As a result, some characteristic physical properties of the metallomacrocycle could be transferred to the new material. The bisphenol A diglycidyl ether (BADGE, n = 0 and hemin (a protoporphyrin IX containing the Fe(III ion, and an additional chloride ligand have been chosen. The new material has been characterized by differential scanning calorimetry (DSC, thermogravimetric analysis (TGA, Fourier Transform Infrared (FT-IR, Nuclear Magnetic Resonance (NMR, Transmission Electron Microscopy (TEM, and magnetic susceptibility measurements. Fe(III remains in the high-spin state during the curing process and, consequently, the final material exhibits the magnetic characteristics of hemin. The loss of the chlorine atom ligand during the cure of the resin allows that Fe(III can act as Lewis acid, catalyzing the crosslinking reactions. At high BADGE n = 0/hemin ratios, the formation of ether and ester bonds occurs simultaneously during the process.

Polymerization shrinkage stress of composite resins and resin cements - What do we need to know?

Science.gov (United States)

Soares, Carlos José; Faria-E-Silva, André Luis; Rodrigues, Monise de Paula; Vilela, Andomar Bruno Fernandes; Pfeifer, Carmem Silvia; Tantbirojn, Daranee; Versluis, Antheunis

2017-08-28

Polymerization shrinkage stress of resin-based materials have been related to several unwanted clinical consequences, such as enamel crack propagation, cusp deflection, marginal and internal gaps, and decreased bond strength. Despite the absence of strong evidence relating polymerization shrinkage to secondary caries or fracture of posterior teeth, shrinkage stress has been associated with post-operative sensitivity and marginal stain. The latter is often erroneously used as a criterion for replacement of composite restorations. Therefore, an indirect correlation can emerge between shrinkage stress and the longevity of composite restorations or resin-bonded ceramic restorations. The relationship between shrinkage and stress can be best studied in laboratory experiments and a combination of various methodologies. The objective of this review article is to discuss the concept and consequences of polymerization shrinkage and shrinkage stress of composite resins and resin cements. Literature relating to polymerization shrinkage and shrinkage stress generation, research methodologies, and contributing factors are selected and reviewed. Clinical techniques that could reduce shrinkage stress and new developments on low-shrink dental materials are also discussed.

Method of heat decomposition for chemical decontaminating resin waste

International Nuclear Information System (INIS)

Kikuchi, Akira.

1988-01-01

Purpose: To make resin wastes into non-deleterious state, discharge them into a resin waste storage tank of existent radioactive waste processing facility and store and dispose them. Constitution: In the processing of chemical decontaminating resin wastes, iron exchange resins adsorbing chemical decontaminating agents comprising a solution of citric acid, oxalic acid, formic acid and EDTA alone or as a mixture of them are heated to dry, thermally decomposed and then separated from the ion exchange resins. That is, the main ingredients of the chemical decontaminating agents are heat-decomposed when heated and dried at about 250 deg C in air and converted into non-toxic gases such as CO, CO 2 , NO, NO 2 or H 2 O. Further, since combustion or carbonization of the basic materials for the resin is not caused at such a level of temperature, the resin wastes removed with organic acid and chelating agents are transferred to an existent resin waste storage tank and stored therein. In this way, facility cost and radiation exposure can remarkably be decreased. (Kamimura, M.)

Retrofitting Trojan Nuclear Plant's spent resin transfer system

International Nuclear Information System (INIS)

Pierce, R.E.

1979-01-01

The spent resin slurry transport system at the Trojan Nuclear Plant operated by Portland General Electric Company is one of the most advanced systems of its type in the nuclear industry today. The new system affords the plant's operators safe remote sonic indication for spent resin and cover water levels, manual remote dewatering and watering capability to establish desirable resin-to-water volumetric ratios, reliable non-mechanical resin agitation utilizing fixed spargers, and controllable process flow utilizing a variable speed recessed impeller pump

Evaluation of the resin oxidation process using Fenton's reagent

International Nuclear Information System (INIS)

Araujo, Leandro G.; Goes, Marcos M.; Marumo, Julio T.

2013-01-01

The ion exchange resin is considered radioactive waste after its final useful life in nuclear reactors. Usually, this type of waste is treated with the immobilization in cement Portland, in order to form a solid monolithic matrix, reducing the possibility of radionuclides release in to environment. Because of the characteristic of expansion and contraction of the resins in presence of water, its incorporation in the common Portland cement is limited in 10% in direct immobilization, causing high costs in the final product. A pre-treatment would be able to reduce the volume, degrading the resins and increasing the load capacity of this material. This paper is about a method of degradation of ion spent resins from the nuclear research reactor of Nuclear and Energy Research Institute (IPEN/CNEN-SP), Brazil, using the Fenton's reagent. The resin evaluated was a mixture of cationic and anionic resins. The reactions were conducted by varying the concentration of the catalyst (25 to 80 mM), with and without external heat. The time of reaction was two hours. The concentration of 50 mM of catalyst was the most effective in degrading approximately 99%. The resin degradation was confirmed by the presence of CaCO 3 as a white precipitate resulting from the reaction between the Ca(OH) 2 and the CO 2 from the resin degradation. It was possible to degrade the resins without external heating. The calcium carbonates showed no correlation with the residual resin mass. (author)

Electrodialytic decontamination of spent ion exchange resins

International Nuclear Information System (INIS)

Nott, B.R.

1982-01-01

Development of a novel electrodialytic decontamination process for the selective removal of radioactive Cs from spent ion exchange resins containing large amounts of Li is described. The process involves passage of a dc electric current through a bed of the spent ion exchange resin in a specially designed electrodialytic cell. The radiocesium so removed from a volume of the spent resin is concentrated onto a much smaller volume of a Cs selective sorbent to achieve a significant radioactive waste volume reduction. Technical feasibility of the electrodialytic resin decontamination process has been demonstrated on a bench scale with a batch of simulated spent ion exchange resin and using potassium cobalt ferrocyanide as the Cs selective sorbent. A volume reduction factor between 10 and 17 has been estimated. The process appears to be economically attractive. Improvements in process economics can be expected from optimization of the process. Other possible applications of the EDRD process have been identified

Volumetric polymerization shrinkage of contemporary composite resins

OpenAIRE

Nagem Filho, Halim; Nagem, Haline Drumond; Francisconi, Paulo Afonso Silveira; Franco, Eduardo Batista; Mondelli, Rafael Francisco Lia; Coutinho, Kennedy Queiroz

2007-01-01

The polymerization shrinkage of composite resins may affect negatively the clinical outcome of the restoration. Extensive research has been carried out to develop new formulations of composite resins in order to provide good handling characteristics and some dimensional stability during polymerization. The purpose of this study was to analyze, in vitro, the magnitude of the volumetric polymerization shrinkage of 7 contemporary composite resins (Definite, Suprafill, SureFil, Filtek Z250, Fill ...

Petroleum Resins: Separation, Character, and Role in Petroleum

DEFF Research Database (Denmark)

Andersen, Simon Ivar; Speight, James

2001-01-01

are precipitated, adsorbents are added to the n-pentane solutions of the resins and oils, by which process the resins are adsorbed and subsequently recovered by the use of a more polar solvent, and the oils remain in solution. The resin fraction plays an important role in the stability of petroleum and prevents...... separation of the asphaltene constituents as a separate phase. Indeed, the absence of the resin fraction (produced by a variety of methods) from the maltenes influences the ability of the de-resined maltenes to accommodate the asphaltenes either in solution or as a stable part of a colloidal system. In spite....... Suggestions are also made regarding current thoughts of the role of these constituents on the structure and stability of petroleum....

Heat-cured acrylic resin versus light-activated resin: a patient, professional and technician-based evaluation of mandibular implant-supported overdentures.

Science.gov (United States)

Asal, S A; Al-AlShiekh, H M

2017-12-01

Although light-activated resins (Eclipse) have been reported to possess superior physical and mechanical properties compared with the heat-cured acrylic resins (Lucitone-199), a few studies have compared overdentures with a locator attachment constructed from heat-cured acrylic resins with those constructed from light-activated resins. This clinical study was designed to compare the performance of a mandibular implant-supported overdenture constructed from a heat-cured acrylic resin (Lucitone-199) with that of an overdenture constructed from a light-activated resin (Eclipse). Ten participants received two identical mandibular implant-retained overdentures (Lucitone-199 and Eclipse) opposing one maxillary denture in a random order. Each mandibular overdenture was delivered and worn for 6 months, and two weeks of rest was advised between wears to minimize any carryover effects. Three questionnaires were devised. The first questionnaire (patient evaluation) focused on evaluating different aspects of the denture and overall satisfaction. The second questionnaire (professional dentist evaluation) was based on a clinical evaluation of soft tissues, complications, and the applied technique. The third questionnaire (technician evaluation) involved ranking the different manufacturing steps of the denture and overall preferences. The obtained data was statistically analyzed using an independent sample t-test and the Wilcoxon rank-sum test. The clinician and technician preferred the Eclipse dentures because of their technical aspects, whereas the patients preferred the Lucitone-199 dentures for their aesthetic properties. Implant-supported overdentures constructed from a heat-cured acrylic resin showed superior aesthetics and had a better odor compared with those constructed from a light-cured resin.

Comparison of the Amount of Fluoride Release from Nanofilled Resin Modified Glass Ionomer Conventional and Resin Modified Glass Ionomer Cements

Directory of Open Access Journals (Sweden)

Sumitha Upadhyay

2013-01-01

Full Text Available Objective: To investigate and compare the amount of fluoride release of conventional, resin modified and nanofilled resin modified glass ionomer cements.Materials and Methods: Tablets of glass-ionomer cements were immersed in deionized water and incubated at 37◦C. After 1, 2, 7, 15 and 30 days, fluoride ion was measured under normal atmospheric conditions by fluoride ion selective electrode. Buffer (TISAB II was used to decomplex the fluoride ion and to provide a constant background ionic strength and to maintain the pH of water between 5.0 and 5.5 as the fluoride electrode is sensitive to changes in pH. Statistical evaluation was carried out by one way ANOVA (Analysis of Variance using SPSS 11.0. The significance level was set at p< 0.05.Results: The release of fluoride was highest on day 1 and there was a sudden fall on day 2 in all three groups. Initially fluoride release from conven-tional glass-ionomer cement was highest compared to the other two glass-ionomer cements, but the amount drastically reduced over the period. Although the amount of fluoride release was less than both the resin modified and nanofilled resin modified glass-ionomer cement, the release was sustained consistently for 30 daysConclusion: The cumulative fluoride release of nanofilled resin modified glass ionomer cement was very less compared to the conventional and resin modified glass ionomer cements and Nanofilled resin modified glass ionomer cement released less but steady fluoride as compared to other resin modified glass ionomer cements.

A comparative study to determine strength of autopolymerizing acrylic resin and autopolymerizing composite resin influenced by temperature during polymerization: An In Vitro study

Directory of Open Access Journals (Sweden)

Anuj Chhabra

2017-01-01

Full Text Available Aim: Temporary coverage of a prepared tooth is an important step during various stages of the fixed dental prosthesis. Provisional restorations should satisfy proper mechanical requirements to resist functional and nonfunctional loads. A few studies are carried out regarding the comparison of the effect of curing environment, air and water, on mechanical properties of autopolymerizing acrylic and composite resin. Hence, the aim of this study was to compare the transverse strength of autopolymerizing acrylic resin and autopolymerizing composite resin as influenced by the temperature of air and water during polymerization. Materials and Methods: Samples of autopolymerizing acrylic resin and composite resin were prepared by mixing as per manufacturer's instructions and were placed in a preformed stainless steel mold. The mold containing the material was placed under different controlled conditions of water temperature and air at room temperature. Polymerized samples were then tested for transverse strength using an Instron universal testing machine. Results: Alteration of curing condition during polymerization revealed a significant effect on the transverse strength. The transverse strength of acrylic resin specimens cured at 60°C and composite resin specimens cured at 80°C was highest. Polymerizing the resin in cold water at 10°C reduced the mechanical strength. Conclusions: Polymerization of the resin in hot water greatly increased its mechanical properties. The method of placing resin restoration in hot water during polymerization may be useful for improving the mechanical requirements and obtaining long-lasting performance.

Solidification of ion exchange resin wastes in hydraulic cement

International Nuclear Information System (INIS)

Neilson, R.M. Jr.; Kalb, P.; Fuhrmann, M.; Colombo, P.

1982-01-01

Work has been conducted to investigate the solidification of ion exchange resin wastes with portland cements. These efforts have been directed toward the development of acceptable formulations for the solidification of ion exchange resin wastes and the characterization of the resultant waste forms. This paper describes formulation development work and defines acceptable formulations in terms of ternary phase compositional diagrams. The effects of cement type, resin type, resin loading, waste/cement ratio and water/cement ratio are described. The leachability of unsolidified and solidified resin waste forms and its relationship to full-scale waste form behavior is discussed. Gamma irradiation was found to improve waste form integrity, apparently as a result of increased resin crosslinking. Modifications to improve waste form integrity are described. 3 tables

Ballistic properties of bidirectional fiber/resin composites

International Nuclear Information System (INIS)

Dimeski, Dimko; Spaseska, Dijana

2004-01-01

The aim of the research was to make evaluation of the ballistic strength of four different fiber/resin composites intended to be used in manufacturing of ballistic items for personal protection. Research has been performed on glass, ballistic nylon, aramid and HPPE (High Performance Polyethylene) plainly woven fabric based composites. As a matrix system, in all cases, polyvinylbutyral modified phenolic resin was used. For the investigation, areal weight range 2 - 9 kg/m 2 chosen was, which is applicable for personal ballistic protection and the ultimate resin content range 20 - 50 vol.%. Ballistic test of the composites has shown that the best results exhibit HPPE based composites; aramid based composites have been the second best followed by the polyamide based composites. The worst results have been shown by the glass based composites. All composites with lower resin content (20%) have performed much better than their counterparts with higher resin content (50 %).The plot of the ballistic strength (V 50 ) versus areal weight has shown a linear increase of V 50 with the increase of areal weight. The ballistic strength of the composites is highly dependant on the fiber/resin ratio and increases with the increase of the fiber content. (Author)

21 CFR 872.3820 - Root canal filling resin.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Root canal filling resin. 872.3820 Section 872...) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3820 Root canal filling resin. (a) Identification. A root canal filling resin is a device composed of material, such as methylmethacrylate, intended...

Determination of degradation conditions of exchange resins containing technetium

International Nuclear Information System (INIS)

Rivera S, A.; Monroy G, F.; Quintero P, E.

2014-10-01

The quantification of Tc-99 in spent exchange resins, coming from nuclear power plants, is indispensable to define their administration. The Tc-99 is a pure beta emitter of 210000 years of half-life, volatile and of a high mobility in water and soil. For this reason, the objective of this work is to establish a digestion method of ionic exchange resins containing technetium that retains more than 95% of this radioisotope. Mineralization tests were carried out of a resin Amberlite IRN-150 by means of an oxidation heat, in acid medium, varying the resin mass, the medium volume, the media type, the temperature and the digestion time. The digested samples were analyzed by gas chromatography to estimate the grade of their degradation. The 99m Tc was used as tracer to determine the technetium percentage recovered after mineralizing the resin. The digestion process depends on the temperature and the resin mass. At higher temperature better mineralization of samples and to greater resin mass to a constant temperature, less degradation of the resin. The spectra beta of the 99m Tc and 99 Tc are presented. (Author)

Low activity resin processing and disposal options review

International Nuclear Information System (INIS)

Gardner, F.

1996-01-01

New processing options for low activity resin processing and disposal are available. This presentation reviews the economics and technical requirements associated with the following low activity resin processing options. (1) Bulk release resin. (2) Direct disposal. (3) Decontamination and bulk release of cleaned resin. New processing and disposal options have been developed during 1995. Commercial experience with each of these options will be reviewed and the economics associated with the processing method described in detail. Technical requirements for each option will be identified specifying the activity limits and operational requirements for implementation

[Mechanical and dimensional properties of thermosetting resins for crown (author's transl)].

Science.gov (United States)

Hirasawa, T; Hirano, S; Harashima, I; Hirabayashi, S; Mori, R

1979-10-01

The various mechanical and dimensional properties of seven thermosetting methacrylic resins for crown and one heat-curing methacrylic resin as the control were investigated. The obtained results were as follows. 1. The water sorption, namely amount of sorption water and linear expansion by water sorption of hydrophobic poly-bis-MEPP resins were 50 to 70% of that of the control. But hydrophilic poly-EDMA resins indicated the water sorption about 1 to 1.5 times as much as the control. And a poly-UDMA resin was also hydrophilic as poly-EDMA resins, indicated about 1.3 times as much as the control. 2. The properties of poly-bis-MEPP resins were more excellent than that of poly-EDMA resins especially in the wet condition, at least were equal. 3. A poly-UDMA resin contained so-called organic composite fillers, indicated more excellent properties than other resins on hardness, abrasion resistance, linear coefficient of thermal expansion, compressive strength and bending strength in the dry condition. But, in the wet condition, some of these properties of a poly-UDMA resin were approximately equal to those of other resins.

Performances and improvement of copper-hydrazine complexation deoxidising resin

International Nuclear Information System (INIS)

Liu Fenfen; Zhang Hao; Sun Haijun; Liu Xiaojie

2012-01-01

Copper-hydrazine complexation deoxidising resin is tested to examine its performances including effluent water quality and capacity of deoxidisation. By the means of changing the resin type and regeneration, the deoxidising capacity of the resin can be improved to 13 times more than before. At the same time, physical performances of the resin are also greatly improved while maintaining its velocity of deoxidisation and effluent quality. (authors)

21 CFR 872.3670 - Resin impression tray material.

Science.gov (United States)

2010-04-01

... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3670 Resin impression tray material. (a) Identification. Resin impression tray material is a device intended for use in a two-step dental mold fabricating... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Resin impression tray material. 872.3670 Section...

Bituminous solidification, disposal, transport and burial of spent ion-exchange resins. Part of a coordinated programme on treatment of spent ion exchange resins

International Nuclear Information System (INIS)

Mozes, G.; Kristof, M.

1983-07-01

The project dealing with the incorporation of spent ion-exchange resins into bitumen was performed within the Agency coordinated research programme on treatment of spent ion-exchange resins. Physical and chemical properties of commercial ion-exchange resins, bitumens and bituminized resins were studied. It was shown that bitumen with low oil content and with a softening point of 60-70 deg. C are applicable for the incorporation of resins. The final waste form is allowed to contain maximum 50% resin. The comprehensive study of the biological resistance of B-30 bitumen was performed. That showed that any bacteriological attack can be regarded as generally insignificant. A continuously operating technology was realized on a semi-plant scale. The best operating conditions of this technology were determined. On the basis of the experience gained from the experiments a design of the bituminization plant of 50m 3 dry resin/year treatment capacity was proposed

Modified resins for solid-phase extraction

Science.gov (United States)

Fritz, James S.; Sun, Jeffrey J.

1991-12-10

A process of treating aqueous solutions to remove organic solute contaminants by contacting an aqueous solution containing polar organic solute contaminants with a functionalized polystyrene-divinyl benzene adsorbent resin, with the functionalization of said resin being accomplished by organic hydrophilic groups such as hydroxymethyl, acetyl and cyanomethyl.

Microbial treatment of ion exchange resins

International Nuclear Information System (INIS)

Kouznetsov, A.; Kniazev, O.

2001-01-01

A bioavailability of ion exchange resins to a microbial destruction as one of the alternative methods of compacting used ionites from the nuclear fuel manufacturing cycle enterprises has been investigated. The bio-destruction was studied after a preliminary chemical treatment or without it. A sensitivity of the ion exchange resins (including highly acidic cationite KU-2-8) to the microbial destruction by heterotrophic and chemo-litho-trophic microorganisms under aerobic conditions was shown in principle. The biodegradation of the original polymer is possible in the presence of the water soluble fraction of the resin obtained after its treatment by Fenton reagent and accelerated in the presence of Mn-ions in optimal concentration 1-2 g of Mn per liter of medium. Thus, the process of bio-destruction of ionite polymer by heterotrophic microorganisms can be compared with the bio-destruction of lignin or humic substances. The optimum parameters of bio-destruction and microorganisms used must be different for resins with different functional groups. (authors)

Preparation of extractive resins for producing terbium-161

International Nuclear Information System (INIS)

De la Cruz B, C. C.; Monroy G, F.

2009-10-01

This paper presents the development of a methodology for extractive resins preparation to base of HDEHP, which allows to separation of Tb from Gd generating an own technology of preparation of these resins. The study included the extractive resins preparation from 6 different supports: kieselguhr Dg, alumina, red volcanic rock, chiluca, quarry and fluorite; two treatment types of of supports and varied concentrations of HDEHP extractant (di(2-etil hexyl) orthophosphoric acid), in order to determine which resin has improved efficiency of Gd and Tb separation, and radionuclide purity of 161 Tb. Resins were prepared to base of kieselguhr to determine the most appropriate silicon deposition process. Two silicon deposition treatments were realized: treatment I , by contact with silicon deposition solution (dimethyldichlorosilane / heptane 1:30) and treatment II by contact with vapors of dimethyldichlorosilane in vacuum. The extractant retention was carried out to different concentrations of HDEHP / acetone: 1:4, 1:8, 1:15, 1:20, 1:30 and 1:40. According to the results, there is not direct relation of HDEHP concentration used in extractive resins preparation to base of kieselguhr over the efficiency of Gd and Tb separation and of radionuclide purity of 161 Tb. The effect of support in the efficiency of Gd and Tb separation was studied to prepare resins with the supports kieselguhr, alumina, quarry, chiluca, volcanic rock and fluorite, using the silicon deposition treatment II for the supports and a concentration of HDEHP / acetone 1:20, for extractant retention. Only resins based on kieselguhr could separate to Gd from Tb quantitatively, the resin at a concentration of HDEHP / Acetone 1:20 was the best results obtained in Gd and Tb separation, achieving a separation efficiency greater than 90% and a radionuclide purity higher than 99%. (Author)

A method for producing a hydrocarbon resin

Energy Technology Data Exchange (ETDEWEB)

Tsachev, A B; Andonov, K S; Igliyev, S P

1980-11-25

Rock coal resin (KS), for instance, with a relative density of 1,150 to 1,190 kilograms per cubic meter, which contains 8 to 10 percent naphthaline, 1.5 to 2.8 percent phenol and 6 to 15 percent substances insoluble in toluene, or its mixture with rock coal or oil fractions of resin are subjected to distillation (Ds) in a pipe furnace with two evaporators (Is) and a distillation tower with a temperature mode in the second stage of 320 to 360 degrees and 290 to 340 degrees in the pitch compartment. A hydrocarbon resin is produced with a high carbon content, especially for the production of resin and dolomite refractory materials, as well as fuel mixtures for blast furnace and open hearth industry.

Amine chemistry. Update on impact on resin

International Nuclear Information System (INIS)

Bachman, Gregory; Kellogg, Douglas; Wilkes, Marty

2012-01-01

Impurity removal in the steam cycle and the associated prevention of corrosion and/or fouling of system components are the goals of ion exchange resins. However, in many instances (such as a switch to amine chemistry or a change in product specifications), resins do not remove, and, in fact, contribute impurities to the steam cycle. This paper reviews recent data compiled to determine the direct and indirect effects of amines on ion exchange resins used in the power industry. Water chemistries have improved in recent years, in large part due to changes in chemistry and resins, but it is necessary to continue to develop products, processes and techniques to reduce impurities and improve overall water chemistry in power plant systems. (orig.)

Amine chemistry. Update on impact on resin

Energy Technology Data Exchange (ETDEWEB)

Bachman, Gregory; Kellogg, Douglas [Siemens Industry, Inc., Rockford, IL (United States). Technology and Lab Services; Wilkes, Marty [Siemens Industry, Inc., Rockford, IL (United States). Water Technologies Div.

2012-03-15

Impurity removal in the steam cycle and the associated prevention of corrosion and/or fouling of system components are the goals of ion exchange resins. However, in many instances (such as a switch to amine chemistry or a change in product specifications), resins do not remove, and, in fact, contribute impurities to the steam cycle. This paper reviews recent data compiled to determine the direct and indirect effects of amines on ion exchange resins used in the power industry. Water chemistries have improved in recent years, in large part due to changes in chemistry and resins, but it is necessary to continue to develop products, processes and techniques to reduce impurities and improve overall water chemistry in power plant systems. (orig.)

Potential contribution of exposed resin to ecosystem emissions of monoterpenes

Science.gov (United States)

Eller, Allyson S. D.; Harley, Peter; Monson, Russell K.

2013-10-01

Conifers, especially pines, produce and store under pressure monoterpene-laden resin in canals located throughout the plant. When the plants are damaged and resin canals punctured, the resin is exuded and the monoterpenes are released into the atmosphere, a process that has been shown to influence ecosystem-level monoterpene emissions. Less attention has been paid to the small amounts of resin that are exuded from branches, expanding needles, developing pollen cones, and terminal buds in the absence of any damage. The goal of this study was to provide the first estimate of the potential of this naturally-exposed resin to influence emissions of monoterpenes from ponderosa pine (Pinus ponderosa) ecosystems. When resin is first exuded as small spherical beads from undamaged tissues it emits monoterpenes to the atmosphere at a rate that is four orders of magnitude greater than needle tissue with an equivalent exposed surface area and the emissions from exuded beads decline exponentially as the resin dries. We made measurements of resin beads on the branches of ponderosa pine trees in the middle of the growing season and found, on average, 0.15 cm2 of exposed resin bead surface area and 1250 cm2 of total needle surface area per branch tip. If the resin emerged over the course of 10 days, resin emissions would make up 10% of the ecosystem emissions each day. Since we only accounted for exposed resin at a single point in time, this is probably an underestimate of how much total resin is exuded from undamaged pine tissues over the course of a growing season. Our observations, however, reveal the importance of this previously unrecognized source of monoterpenes emitted from pine forests and its potential to influence regional atmospheric chemistry dynamics.

Polymerization shrinkage stress of composite resins and resin cements – What do we need to know?

Directory of Open Access Journals (Sweden)

Carlos José SOARES

2017-08-01

Full Text Available Abstract Polymerization shrinkage stress of resin-based materials have been related to several unwanted clinical consequences, such as enamel crack propagation, cusp deflection, marginal and internal gaps, and decreased bond strength. Despite the absence of strong evidence relating polymerization shrinkage to secondary caries or fracture of posterior teeth, shrinkage stress has been associated with post-operative sensitivity and marginal stain. The latter is often erroneously used as a criterion for replacement of composite restorations. Therefore, an indirect correlation can emerge between shrinkage stress and the longevity of composite restorations or resin-bonded ceramic restorations. The relationship between shrinkage and stress can be best studied in laboratory experiments and a combination of various methodologies. The objective of this review article is to discuss the concept and consequences of polymerization shrinkage and shrinkage stress of composite resins and resin cements. Literature relating to polymerization shrinkage and shrinkage stress generation, research methodologies, and contributing factors are selected and reviewed. Clinical techniques that could reduce shrinkage stress and new developments on low-shrink dental materials are also discussed.

Development of a High-Throughput Ion-Exchange Resin Characterization Workflow.

Science.gov (United States)

Liu, Chun; Dermody, Daniel; Harris, Keith; Boomgaard, Thomas; Sweeney, Jeff; Gisch, Daryl; Goltz, Bob

2017-06-12

A novel high-throughout (HTR) ion-exchange (IEX) resin workflow has been developed for characterizing ion exchange equilibrium of commercial and experimental IEX resins against a range of different applications where water environment differs from site to site. Because of its much higher throughput, design of experiment (DOE) methodology can be easily applied for studying the effects of multiple factors on resin performance. Two case studies will be presented to illustrate the efficacy of the combined HTR workflow and DOE method. In case study one, a series of anion exchange resins have been screened for selective removal of NO 3 - and NO 2 - in water environments consisting of multiple other anions, varied pH, and ionic strength. The response surface model (RSM) is developed to statistically correlate the resin performance with the water composition and predict the best resin candidate. In case study two, the same HTR workflow and DOE method have been applied for screening different cation exchange resins in terms of the selective removal of Mg 2+ , Ca 2+ , and Ba 2+ from high total dissolved salt (TDS) water. A master DOE model including all of the cation exchange resins is created to predict divalent cation removal by different IEX resins under specific conditions, from which the best resin candidates can be identified. The successful adoption of HTR workflow and DOE method for studying the ion exchange of IEX resins can significantly reduce the resources and time to address industry and application needs.

Development and application of high performance resins for crud removal

International Nuclear Information System (INIS)

Deguchi, Tatsuya; Izumi, Takeshi; Hagiwara, Masahiro

1998-01-01

The development of crud removal technology has started with the finding of the resin aging effect that an old ion exchange resin, aged by long year of use in the condensate demineralizer, had an enhanced crud removal capability. It was confirmed that some physical properties such as specific surface area and water retention capacity were increased due to degradation caused by long year of contact with active oxygens in the condensate water. So, it was speculated that those degradation in the resin matrix enhanced the adsorption of crud particulate onto the resin surface, hence the crud removal capability. Based on this, crud removal resin with greater surface area was first developed. This resin has shown an excellent crud removal efficiency in an actual power plant, and the crud iron concentration in the condensate effluent was drastically reduced by this application. However, the cross-linkage of the cation resin had to be lowered in a delicate manner for that specific purpose, and this has caused higher organic leachables from the resin, and the sulfate level in the reactor was raised accordingly. Our major goals, therefore, has been to develop a crud resin of as little organic leachables as possible with keeping the original crud removal efficiency. It was revealed through the evaluation of the first generation crud resin and its improved version installed in the actual condensate demineralizers that there was a good correlation between crud removal efficiency and organic leaching rate. The bast one among a number of developmental resins has shown the organic leaching rate of 1/10 of that of the original crud resin (ETR-C), and the crud removal efficiency of 90%. So far as we understand, the resin was considered to have the best overall balance between crud removal and leaching characteristics. The result of six month evaluation of this developmental resin, ETR-C3, in one vessel of condensate demineralizer of a power plant will be presented. (J.P.N.)

21 CFR 177.1595 - Polyetherimide resin.

Science.gov (United States)

2010-04-01

... polyetherimide resin identified in this section may be safely used as an article or component of an article... substances required in the production of basic resins or finished food-contact articles. The optional... and Applied Nutrition (HFS-200), Food and Drug Administration, 5100 Paint Branch Pkwy., College Park...

21 CFR 177.2440 - Polyethersulfone resins.

Science.gov (United States)

2010-04-01

... Components of Articles Intended for Repeated Use § 177.2440 Polyethersulfone resins. Polyethersulfone resins identified in paragraph (a) of this section may be safely used as articles or components of articles intended... Petition Control (HFS-215), Center for Food Safety and Applied Nutrition, 1110 Vermont Ave. NW., suite 1200...

K Basin sludge/resin bead separation test report

International Nuclear Information System (INIS)

Squier, D.M.

1998-01-01

The K Basin sludge is an accumulation of fuel element corrosion products, organic and inorganic ion exchange materials, canister gasket materials, iron and aluminum corrosion products, sand, dirt and minor amounts of other organic material. The sludge will be collected and treated for storage and eventual disposal. This process will remove the large solid materials by a 1/4 inch screen. The screened material will be subjected to nitric acid in a chemical treatment process. The organic ion exchange resin beads produce undesirable chemical reactions with the nitric acid. The resin beads must be removed from the bulk material and treated by another process. An effective bead separation method must extract 95% of the resin bead mass without entraining more than 5% of the other sludge component mass. The test plan I-INF-2729, ''Organic Ion Exchange Resin Separation Methods Evaluation,'' proposed the evaluation of air lift, hydro cyclone, agitated slurry and elutriation resin bead separation methods. This follows the testing strategy outlined in section 4.1 of BNF-2574, ''Testing Strategy to Support the Development of K Basins Sludge Treatment Process''. Engineering study BNF-3128, ''Separation of Organic Ion Exchange Resins from Sludge,'' Rev. 0, focused the evaluation tests on a method that removed the fine sludge particles by a sieve and then extracted the beads by means of a elutriation column. Ninety-nine percent of the resin beads are larger than 125 microns and 98.5 percent are 300 microns and larger. Particles smaller than 125 microns make up the largest portion of sludge in the K Basins. Eliminating a large part of the sludge's non-bead component will reduce the quantity that is lifted with the resin beads in the elutriation column. Resin bead particle size distribution measurements are given in Appendix A The Engineering Testing Laboratory conducted measurements of a elutriation column's ability to extract resin beads from a sieved, non-radioactive sludge

Development of heat resistant ion exchange resin. First Report

International Nuclear Information System (INIS)

Onozuka, Teruo; Shindo, Manabu

1995-01-01

In nuclear power stations, as a means of maintaining the soundness of nuclear reactors, the cleaning of reactor cooling water has been carried out. But as for the ion exchange resin which is used as the cleaning agent in the filtrating and desalting facility in reactor water cleaning system, since the heat resistance is low, high temperature reactor water is cooled once and cleaned, therefore large heat loss occurs. If the cleaning can be done at higher temperature, the reduction of heat loss and compact cleaning facilities become possible. In this study, a new ion exchange resin having superior heat resistance has been developed, and the results of the test of evaluating the performance of the developed ion exchange resin are reported. The heat loss in reactor water cleaning system, the heat deterioration of conventional ion exchange resin, and the development of the anion exchange resin of alkyl spacer type are described. The outline of the performance evaluation test, the experimental method, and the results of the heat resistance, ion exchange characteristics and so on of C4 resin are reported. The with standable temperature of the developed anion exchange resin was estimated as 80 - 90degC. The ion exchange performance at 95degC of this resin did not change from that at low temperature in chloride ions and silica, and was equivalent to that of existing anion exchange resin. (K.I.)

Development of heat resistant ion exchange resin. First Report

Energy Technology Data Exchange (ETDEWEB)

Onozuka, Teruo; Shindo, Manabu [Tohoku Electric Power Co., Inc., Sendai (Japan)

1995-01-01

In nuclear power stations, as a means of maintaining the soundness of nuclear reactors, the cleaning of reactor cooling water has been carried out. But as for the ion exchange resin which is used as the cleaning agent in the filtrating and desalting facility in reactor water cleaning system, since the heat resistance is low, high temperature reactor water is cooled once and cleaned, therefore large heat loss occurs. If the cleaning can be done at higher temperature, the reduction of heat loss and compact cleaning facilities become possible. In this study, a new ion exchange resin having superior heat resistance has been developed, and the results of the test of evaluating the performance of the developed ion exchange resin are reported. The heat loss in reactor water cleaning system, the heat deterioration of conventional ion exchange resin, and the development of the anion exchange resin of alkyl spacer type are described. The outline of the performance evaluation test, the experimental method, and the results of the heat resistance, ion exchange characteristics and so on of C4 resin are reported. The with standable temperature of the developed anion exchange resin was estimated as 80 - 90degC. The ion exchange performance at 95degC of this resin did not change from that at low temperature in chloride ions and silica, and was equivalent to that of existing anion exchange resin. (K.I.).

HIGH ASPECT RATIO ION EXCHANGE RESIN BED - HYDRAULIC RESULTS FOR SPERICAL RESIN BEADS

International Nuclear Information System (INIS)

Duignan, M; Charles Nash, C; Timothy Punch, T

2007-01-01

A principal role of the DOE Savannah River Site is to safely dispose of a large volume of liquid nuclear waste held in many storage tanks. An in-tank ion exchange unit is being considered for cesium removal to accelerate waste processing. This unit is planned to have a relatively high bed height to diameter ratio (10:1). Complicating the design is the need to cool the ion exchange media; therefore, the ion exchange column will have a central cooling core making the flow path annular. To separate cesium from waste the media being considered is made of resorcinol formaldehyde resin deposited on spherical plastic beads and is a substitute for a previously tested resin made of crystalline silicotitanate. This spherical media not only has an advantage of being mechanically robust, but, unlike its predecessor, it is also reusable, that is, loaded cesium can be removed through elution and regeneration. Resin regeneration leads to more efficient operation and less spent resin waste, but its hydraulic performance in the planned ion exchange column was unknown. Moreover, the recycling process of this spherical resorcinol formaldehyde causes its volume to significantly shrink and swell. To determine the spherical media's hydraulic demand a linearly scaled column was designed and tested. The waste simulant used was prototypic of the wastes' viscosity and density. This paper discusses the hydraulic performance of the media that will be used to assist in the design of a full-scale unit

Oligosilylarylnitrile: The Thermoresistant Thermosetting Resin with High Comprehensive Properties.

Science.gov (United States)

Wang, Mingcun; Ning, Yi

2018-04-11

One of the highest thermoresistant thermosetting resins ever studied so far, oligosilylarylnitrile resin, was investigated first in this study. Oligosilylarylnitrile was synthesized by lithium-reduced Wurtz-Fittig condensation reaction, and the prepared viscous resin exhibited moderate rheological behaviors while heated purely or together with 20% polysilazane as a cross-linking agent. The thermal curing temperatures were found by differential scanning calorimetry at 268 °C (pure) and 158 °C (with the polysilazane cross-linking agent), which is comparably close to that of polysilylarylacetylene resin (normally at 220-250 °C) but much lower than those of polyimide and phthalonitrile resins (normally >300 °C), indicating the admirable material processability of oligosilylnitrile. The cured oligosilylarylnitrile resins have extremely high thermal resistance, indicated by the results of thermogravimetric analysis (the mass residue at 800 °C is >90% under N 2 ) and dynamic mechanical analysis (the glass-transition temperature is >420 °C). The mechanical property of the oligosilylarylnitrile-matrixed silica-cloth reinforced laminate is comparably close to those of polyimide and phthalonitrile but much higher than that of polysilylarylacetylene, indicating the enviable thermal and mechanical properties of oligosilylnitrile. Thus, among the high-temperature resins ever studied so far, the oligosilylarylnitrile resin was found to have the almost best comprehensive characteristics of processability and properties.

Resins characterization strategy at Kozloduy Nuclear Power Plant

International Nuclear Information System (INIS)

Fenoy, A.; González, R.; Molleda, P.; Sánchez, L.; Herrera, J.

2013-01-01

The Consortium ENSA- Gas Natural Fenosa Engineering has a contract with Kozloduy Nuclear Power Plant (KNPP) for the retrieval and conditioning of the resins. Before that, the project deals with resins characterization to verify the fulfillment the Bulgarian authorities’ requirements. The project includes all the resins generated during the operation of the BACKGROUND Resins characterization strategy at Kozloduy Nuclear Power Plant units 1, 2, 3 and 4, which were stored into six big dimensions tanks: four low tanks and two intermediate tanks. They only have a manhole above for tanks access. The methodology and the progress of the work are presented

Zinc and resin bonded NdFeB magnets

International Nuclear Information System (INIS)

Leonowicz, M.; Kaszuwara, W.

2002-01-01

Zinc and resin bonded NdFeB magnets were processed. Basic magnetic parameters as well as compressive strength were evaluated versus annealing temperature and volume fraction of the bonding agent. For the zinc bonded magnets phase composition was investigated. The additional NdZn 5 phase was found in the Zn bonded magnets after annealing. Comparison of the Zn and resin bonded magnets reveals higher remanence for the former and higher coercivity for the latter. For the Zn and resin bonded magnets, 15 wt.% Zn / 370 o C and 7-10 wt.% resin were chosen as the optimal processing parameters. (author)

Posterior bulk-filled resin composite restorations.

DEFF Research Database (Denmark)

van Dijken, Jan WV; Pallesen, Ulla

2016-01-01

up to 4mm as needed to fill the cavity 2mm short of the occlusal cavosurface. The occlusal part was completed with the nano-hybrid resin composite (Ceram X mono+). In the other cavity, the resin composite-only (Ceram X mono+) was placed in 2mm increments. The restorations were evaluated using...... Class II, 4 SDR-CeramX mono+ and 6 CeramXmono+-only restorations. The main reasons for failurewere tooth fracture (6) and secondary caries (4). The annual failure rate (AFR) for all restorations (Class I and II) was for the bulk-filled-1.1% and for the resin composite-only restorations 1...

Management of white spots: resin infiltration technique and microabrasion

Directory of Open Access Journals (Sweden)

Jeong-Hye Son

2011-01-01

Full Text Available This case report compared the effectiveness of resin infiltration technique (Icon, DMG with microabrasion (Opalustre, Ultradent Products, Inc. in management of white spot lesions. It demonstrates that although neither microabrasion nor resin infiltration technique can remove white spot lesions completely, resin infiltration technique seems to be more effective than microabrasion. Therefore resin infiltration technique can be chosen preferentially for management of white spot lesions and caution should be taken for case selection.

21 CFR 177.1580 - Polycarbonate resins.

Science.gov (United States)

2010-04-01

...′-iso-propylidenediphenol with molten diphenyl carbonate in the presence of the disodium salt of 4,4... chloride Monochlorobenzene Not to exceed 500 p.p.m. as residual solvent in finished resin. Pentaerythritol...-88-3) Not to exceed 800 parts per million as residual solvent in finished resin. Triethylamine (c...

Synthesis of improved phenolic and polyester resins

Science.gov (United States)

Delano, C. B.

1980-01-01

Thirty-seven cured phenolic resin compositions were prepared and tested for their ability to provide improved char residues and moisture resistance over state of the art epoxy resin composite matrices. Cyanate, epoxy novolac and vinyl ester resins were investigated. Char promoter additives were found to increase the anaerobic char yield at 800 C of epoxy novolacs and vinyl esters. Moisture resistant cyanate and vinyl ester compositions were investigated as composite matrices with Thornel 300 graphite fiber. A cyanate composite matrix provided state of the art composite mechanical properties before and after humidity exposure and an anaerobic char yield of 46 percent at 800 C. The outstanding moisture resistance of the matrix was not completely realized in the composite. Vinyl ester resins showed promise as candidates for improved composite matrix systems.

Radiation-induced decomposition of anion exchange resins

International Nuclear Information System (INIS)

Baidak, Aliaksandr; LaVerne, Jay A.

2010-01-01

Radiation-induced degradation of the strongly basic anion exchange resin Amberlite TM IRA400 in NO 3 - , Cl - and OH - forms has been studied. The research focused on the formation of molecular hydrogen in the gamma-radiolysis of water slurries of these quaternary ammonium resins with varying water content. Extended studies with various electron scavengers (NO 3 - , N 2 O and O 2 ) prove an important role of e solv - in the formation of H 2 from these resins. An excess production of H 2 in these systems at about 85% water weight fraction was found to be due to trimethylamine, dimethylamine and other compounds that leach from the resin to the aqueous phase. Irradiations with 5 MeV 4 He ions were performed to simulate the effects of α-particles.

Chemical derivatization to enhance chemical/oxidative stability of resorcinol-formaldehyde resin

Energy Technology Data Exchange (ETDEWEB)

Hubler, T.L. [Pacific Northwest National Lab., Richland, WA (United States)

1997-10-01

The goal of this task is to develop modified resorcinol-formaldehyde (R-F) resin to improve the chemical/oxidative stability of the resin. R-F resin is a regenerable organic ion-exchange resin that is selective for cesium ion in highly alkaline, high ionic-strength solutions. R-F resin tends to undergo chemical degradation, reducing its ability to remove cesium ion from waste solutions; the mechanistic details of these decomposition reactions are currently unknown. The approach used for this task is chemical modification of the resin structure, particularly the resorcinol ring unit of the polymer resin. This approach is based on prior characterization studies conducted at Pacific Northwest National Laboratory (PNNL) that indicated the facile chemical degradation of the resin is oxidation of the resorcinol ring to the para-quinone structure, with subsequent loss of ion-exchange sites for cesium ion. R-F resin represents an important alternative to current radiocesium remediation technology for tank wastes at both the Hanford and Savannah River sites, particularly if regenerable resins are needed.

Uptake of actinides by sulphonated phosphinic acid resin from acid medium

International Nuclear Information System (INIS)

Jaya Mohandas; Srinivasa Rao, V.; Vijayakumar, N.; Kumar, T.; Velmurugan, S.; Narasimhan, S.V.

2014-01-01

The removal of uranium and americium from nitric acid solutions by sulphonated phosphinic acid resin has been investigated. The capacity of the sulphonated resin exceeds the capacities of phosphinic acid resin and commercial cation exchange resin. Other advantages of the sulphonated resin for uranium and americium removal include reduced sensitivity to acidity and inert salt concentration. (author)

Evaluation of an Experimental Adhesive Resin for Orthodontic Bonding

Science.gov (United States)

Durgesh, B. H.; Alkheraif, A. A.; Pavithra, D.; Hashem, M. I.; Alkhudhairy, F.; Elsharawy, M.; Divakar, D. D.; Vallittu, P. K.; Matinlinna, J. P.

2017-07-01

The aim of this study was to evaluate in vitro the effect of an experimental adhesive resin for orthodontic bonding by measuring some the chemical and mechanical properties. The resin demonstrated increased values of nanohardness and elastic modulus, but the differences were not significant compared with those for the Transbond XT adhesives. The experimental adhesive resin could be a feasible choice or a substitute for the traditional bis-GMA-based resins used in bonding orthodontic attachments.

Analytical applications of resins containing amide and polyamine functional groups

International Nuclear Information System (INIS)

Orf, G.M.

1977-01-01

Resins are prepared by chemically bonding N,N-dialkylamides and polyamine functional groups to Amberlite XAD-4. These resins are applied to the concentration of metal ions from dilute aqueous solution and the rapid separation of metal ions by high-speed liquid chromatography with continuous on-line detection of the eluent stream. A dibutyl amide resin is used for the separation of uranium(VI), thorium(IV), and zirconium(IV) from each other and several other metal ions. Uranium(VI) and thorium(IV) are determined in the presence of large excesses of foreign metal ions and anions. A practical application of the amide resin is studied by determining uranium in low grade uranium ores. The amide resin is also used for the selective concentration of gold(III) from seawater. A triethylenetetramine resin is used for the separation of copper(II) from equal molar amounts and large excesses of nickel(II), cobalt(II), zinc(II), cadmium(II), iron(III) and aluminum(III). Copper(II), nickel(II), zinc(II), cobalt(II) and cadmium(II) are determined in the presence of large excesses of calcium(II) and magnesium(II). The resin was found to be selective for silver(I) and mercury(II) at low pH values and a rapid separation of equal molar amounts of copper(II) and silver(I) was performed. The resin was also found to have an affinity for anionic metal complexes such as iron(III)-tartrate when the resin is in the hydrogen form. A study of the retention of the anions chromium(III)-tartrate and dichromate at various pH values was performed to better understand the anion exchange properties of the resin. Triethylenetetramine resins were also prepared from polystyrene gel to make a resin with higher capacities for copper

Chelating ion exchange with macroreticular hydroxamic acid resins

International Nuclear Information System (INIS)

Phillips, R.J.

1980-01-01

The synthesis, reactions, and analytical applications of hydroxamic acids, including chelating resins with this functional group, are reviewed. A procedure for attaching N-phenyl hydroxamic acid groups to Amberlite XAD-4 is described. The extraction of 20 metal ions from 2 M hydrochloric acid by this resin is discussed. Conditions for the quantitative extraction and back-extraction of 9 ions are reported. Results are compared with work on solvent extraction with N-phenylbenzohydroxamic acid. Procedures for attaching N-methyl and N-unsubstituted hydroxamic acid groups to Amberlite XAD-4 are described. The N-phenyl, N-methyl, and N-unsubstituted hydroxamic acid resins are compared with respect to metal-ion complexation. The scope of applications for hydroxamic acid resins is investigated by studying the extraction of 19 metal ions as a function of pH. The resins are especially suitable for the extraction of zirconium(IV), titanium(IV), and uranium(IV) from strongly acidic solution. Aluminum(III) is separated from calcium and phosphate by extraction at pH 4. The use of the resins for the purification of reagents, concentration of trace constituents, and chromatographic separation is demonstrated

Ion exchange resins as high-dose radiation dosimeters

International Nuclear Information System (INIS)

Alian, A.; Dessouki, A.; El-Assay, N.B.

1984-01-01

This paper reports on the possibility of using various types of ion exchange resins as high-dose radiation dosimeters, by analysis of the decrease in exchange capacity with absorbed dose. The resins studied are Sojuzchim-export-Moscow Cation Exchanger KU-2 and Anion Exchanger AV-17 and Merck Cation Exchanger I, and Merck Anion Exchangers II and III. Over the dose range 1 to 100 kGy, the systems show linearity between log absorbed dose and decrease in resin ion exchange capacity. The slope of this response function differs for the different resins, depending on their ionic form and degree of cross-linking. The radiation sensitivity increases in the order KU-2; Exchanger I; AV-17; Exchanger II; Exchanger III. Merck resins with moisture content of 21% showed considerably higher radiation sensitivity than those with 2 to 3% moisture content. The mechanism of radiation-induced denaturing of the ion exchanger resins involves cleavage and decomposition of functional substituents, with crosslinking playing a stabilizing role, with water and its radiolytic products serving to inhibit radical recombination and interfering with the protection cage effect of crosslinking. (author)

Hot dewatering and resin encapsulation of intermediate level radioactive waste

International Nuclear Information System (INIS)

Rickman, J.; Birch, D.

1985-01-01

The chemistry of the processes involved in the hot dewatering and encapsulation of alumino-ferric hydroxide floc in epoxide resin have been studied. Pretreatment of the floc to reduce resin attack and hydrolysis and to increase the dimensional stability of the solidified wasteform has been evaluated. It has been demonstrated that removal of ammonium nitrate from the floc and control of the residual water in the resin are important factors in ensuring dimensional stability of the solidified resin. Resin systems have been identified which, together with the appropriate waste pretreatment have successfully encapsulated a simulated magnox sludge producing a stable wasteform having mechanical and physical properties comparable with the basic resin. (author)

Kinetic study of ion exchange in phosphoric acid chelating resin

International Nuclear Information System (INIS)

Brikci-Nigassa, Mounir; Hamouche, Hafida

1995-11-01

Uranium may be recovered as a by product of wet phosphoric acid using a method based on specific ion exchange resins. These resins called chelates contain amino-phosphonic functional groups. The resin studied in this work is a purolite S-940; uranium may be loaded on this resin from 30% P2O5 phosphoric acid in its reduced state. The influence of different parameters on the successive steps of the process have been studied in batch experiments: uranium reduction, loading and oxydation. Uranium may be eluted with ammonium carbonate and the resin regeneration may be done with hydrochloric acid.Ferric ions reduce the effective resin capacity considerably and inert fixation conditions are proposed to enhance uranium loading

A summary of methods for conditioning and immobilizing ion-exchange resins

International Nuclear Information System (INIS)

Speranzini, R.A.; Buckley, L.P.

1983-02-01

Ion-exchange resins are used in CANDU-PHW nuclear power stations to purify heavy water in the primary heat transport (PHT) and moderator systems. Two promising techniques for conditioning spent ion-exchange resins for disposal have been evaluated: direct immobilization and incineration combined with immobilization of the ash and scrubbed off-gases. When ion-exchange resins were immobilized directly, volumes of bitumen products were about 0.75 times the volumes of untreated resin, while the volumes of cement and polyester products were 2 to 3 times larger. While incinerating the resin is an extra processing step, much smaller volumes result from the latter option. Bitumen and glass product volumes were six and ten times smaller, respectively, than the volumes of untreated resin, while cement and polyester product volumes were about one-half the volume of untreated resin. Since the releases of Cs-136 by leaching were lowest for products made by immobilization in glass, PHT resins which have high concentrations of Cs-137 should be vitrified. Moderator resins which have high concentrations of C-14 should be incinerated and the ash and C-14-contaminated scrubbing solutions should be immobilized. By pretreating such resins with calcium chloride or carbon dioxide, the C-14 present on resin could be released at temperatures below the ignition temperature of the resin. The pretreatment technique reduces the amount of inactive carbon dioxide that must be scrubbed to trap the C-14. The releases of C-14 from immobilized barium hydroxide scrubbing solution were the same as releases from immobilized resin

Spherical powder for retaining thermosetting acrylic resin veneers.

Science.gov (United States)

Tanaka, T; Atsuta, M; Uchiyama, Y; Nakabayashi, N; Masuhara, E

1978-03-01

1. Nine different sizes of spherical powder were prepared, and their effectiveness as retentive devices was evaluated against those available commercially. 2. Smaller-diameter spherical powder (No. 5) gave the best results of all retaining devices tested. 3. The physical properties of the resins play an important role in the retentive strength with No. 5 retention beads. The retentive strength was reduced when brittle resin was used. 4. The retentive strength of the resin veneer was greatly affected by the angle of stress at the incisal resin. The retentive strength increased as the angle between the longitudinal axis of the specimen and the direction of stress decreased.

The influence of resin flexural modulus on the magnitude of ceramic strengthening.

LENUS (Irish Health Repository)

Fleming, Garry J P

2012-07-01

The aim was to determine the magnitude of ceramic resin-strengthening with resin-based materials with varying flexural moduli using a regression technique to assess the theoretical strengthening at a \\'zero\\' resin-coating thickness. The hypothesis tested was that experimentally, increasing resin flexural modulus results in increased resin-strengthening observed at a theoretical \\'zero\\' resin-coating thickness.

Characterization of Polyimide Matrix Resins and Prepregs

Science.gov (United States)

Maximovich, M. G.; Galeos, R. M.

1985-01-01

Graphite/polyimide composite materials are attractive candidates for a wide range of aerospace applications. They have many of the virtues of graphite/epoxies, i.e., high specific strengths and stiffness, and also outstanding thermal/oxidative stability. Yet they are not widely used in the aerospace industry due to problems of procesability. By their nature, modern addition polyimide (PI) resins and prepregs are more complex than epoxies; the key to processing lies in characterizing and understanding the materials. Chemical and rheological characterizations are carried out on several addition polyimide resins and graphite reinforced prepregs, including those based on PMR-15, LARC 160 (AP 22), LARC 160 (Curithane 103) and V378A. The use of a high range torque transducer with a Rheometrics mechanical spectrometer allows rheological data to be generated on prepreg materials as well as neat resins. The use of prepreg samples instead of neat resins eliminates the need for preimidization of the samples and the data correlates well with processing behavior found in the shop. Rheological characterization of the resins and prepregs finds significant differences not readily detected by conventional chemical characterization techniques.

40 CFR 721.5762 - Aromatic aldehyde phenolic resin (generic).

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Aromatic aldehyde phenolic resin... Specific Chemical Substances § 721.5762 Aromatic aldehyde phenolic resin (generic). (a) Chemical substance... aromatic aldehyde phenolic resin (PMN P-01-573) is subject to reporting under this section for the...

Effect of various teas on color stability of resin composites.

Science.gov (United States)

Dinç Ata, Gül; Gokay, Osman; Müjdeci, Arzu; Kivrak, Tugba Congara; Mokhtari Tavana, Armin

2017-12-01

To investigate the effect of various teas on color stability of resin composites. Two methacrylate-based (Arabesk Top, Grandio) and a silorane-based (Filtek Silorane) resin composites were used. 110 cylindrical samples of each resin composite were prepared (2 mm thickness and 8 mm diameter), polished and stored in distilled water (37°C for 24 hours). They were randomly divided into 11 groups (n= 10) and color measurements were taken. Then the samples were immersed in tap water (control), a black tea, a green tea or one of the eight herbal-fruit teas (37°C for 1 week) and subsequently subjected to the final color measurements. The color change of samples (ΔE*) was calculated, data were subjected to two-way ANOVA and Tukey's HSD tests. Teas, resin composites and their interactions were significant (P= 0.000). All the teas and control caused color changes in all three resin composites. Rosehip tea caused the most color changes, while tap water showed the least in all resin composites. Arabesk Top had the most staining potential in all the teas and control, whereas Filtek Silorane was the most stain resistant except Grandio immersed in sage tea. Color stability of all resin composites used were affected from both structure of resin materials and constituents of teas used. All resin composites were susceptible to staining by all teas especially rosehip tea. Arabesk Top composite showed the greatest color susceptibility in all teas and Filtek Silorane the least with one exception. Color of resin composites can be negatively affected from teas consumed. Clinicians should advise patients that drinking different kind of teas could intensify surface staining of resin based restorations.

Feasibility of vitrifying EPICOR II organic resins

International Nuclear Information System (INIS)

Buelt, J.L.

1981-11-01

Two laboratory-scale runs have recently been completed to test the feasibility of a single-step incineration/vitrification process for Three Mile Island EPICOR II resins. The process utilizes vitrification equipment, specifically a 15-cm-dia in-can melter, and a specially designed feed technique. Two process tests, each conducted with 1.2 kg of EPICOR II resins loaded with nonradioactive cesium and strontium, showed excellent operational characteristics. Less than 0.8 wt% of the resins were entrained with the gaseous effluents in the second test. Cesium and strontium losses were controlled to 0.71 wt% and less. In addition, all the carbonaceous resins were converted completely to CO 2 with no detectable CO. Future activities are being directed to longer-term tests in laboratory-scale equipment to determine attainable volume reduction, process rates, and material conformance to processing conditions

Method for curing alkyd resin compositions by applying ionizing radiation

International Nuclear Information System (INIS)

Watanabe, T.; Murata, K.; Maruyama, T.

1975-01-01

An alkyd resin composition is prepared by dissolving a polymerizable alkyd resin having from 10 to 50 percent of oil length into a vinyl monomer. The polymerizable alkyd resin is obtained by a half-esterification reaction of an acid anhydride having a polymerizable unsaturated group and an alkyd resin modified with conjugated unsaturated oil having at least one reactive hydroxyl group per one molecule. The alkyd resin composition thus obtained is coated on an article, and ionizing radiation is applied on the article to cure the coated film thereon. (U.S.)

Pengaruh Minuman Kopi terhadap Perubahan Warna pada Resin Komposit

Directory of Open Access Journals (Sweden)

Aprilia Aprilia

2015-10-01

Full Text Available Objective: The aim of this research was to investigate the influence of coffee beverage on hybrid composite resin discoloration. Material and method: This study used hybrid composite resin with A3 color, and was done by soaking composite resin plates in coffee solution for 1, 3, 5, and 7 days, corresponding to equivalent coffee usage for 6 months, 1, 1.5, and 2 years. The same measurements of reflectance were done before and after soaking into coffee solution. In the measurement, a beam from He-Ne laser is reflected by the sample to a photovoltaic cell type BOY-47, which provides a voltage signal accordig to the intensity of reflected light. Results: There was a significant difference between composite resin plates before and after soaking into coffee dilution for 1, 3, 5, and 7 days. Conclusion: Composite resin is discolored after soaking into a coffee solution, suggesting that coffee usage will have a discoloring effect on dental composite resin.

Ontario Hydro Research Division's program for treatment of spent ion-exchange resins

International Nuclear Information System (INIS)

Nott, B.R.; Dodd, D.J.R.

1981-09-01

A brief review of the evolution of work programmes for chemical treatment of spent ion-exchange resins in Ontario Hydro's Research Division is presented. Attention has been focussed on pre-treatment processes for the treatment of the spent resins prior to encapsulation of the products in solid matrices. Spent Resin Regeneration and Acid Stripping processes were considered in some detail. Particular attention was paid to carbon-14 on spent resins, its determination in and removal from the spent resins (with the acid stripping technique). The use of separate cation and anion resin beds instead of mixed bed resins was examined with a view to reducing the volume of resin usage and consequently the volume of waste radioactive ion-exchange resin generated. (author)

SEM and elemental analysis of composite resins

International Nuclear Information System (INIS)

Hosoda, H.; Yamada, T.; Inokoshi, S.

1990-01-01

Twenty-four chemically cured, 21 light-cured anterior, three light-cured anterior/posterior, and 18 light-cured posterior composite resins were examined using scanning electron microscopy, and the elemental composition of their filler particles was analyzed with an energy dispersive electron probe microanalyzer. According to the results obtained, the composite resins were divided into five groups (traditional, microfilled type, submicrofilled type, hybrid type, and semihybrid), with two additional hypothetical categories (microfilled and hybrid). Characteristics of each type were described with clinical indications for selective guidance of respective composite resins for clinical use

21 CFR 177.1655 - Polysulfone resins.

Science.gov (United States)

2010-04-01

... disodium salt of 4,4′-isopropylidenediphenol is made to react with 4,4′-dichlorodiphenyl sulfone in such a... Limitations Dimethyl sulfoxide Not to exceed 50 parts per million as residual solvent in finished basic resin... residual solvent in finished basic resin in paragraph (a)(1) of this section. N-methyl-2-pyrrolidone Not to...

Resin bleed improvement on surface mount semiconductor device

Science.gov (United States)

Rajoo, Indra Kumar; Tahir, Suraya Mohd; Aziz, Faieza Abdul; Shamsul Anuar, Mohd

2018-04-01

Resin bleed is a transparent layer of epoxy compound which occurs during molding process but is difficult to be detected after the molding process. Resin bleed on the lead on the unit from the focused package, SOD123, can cause solderability failure at end customer. This failed unit from the customer will be considered as a customer complaint. Generally, the semiconductor company has to perform visual inspection after the plating process to detect resin bleed. Mold chase with excess hole, split cavity & stepped design ejector pin hole have been found to be the major root cause of resin bleed in this company. The modifications of the mold chase, changing of split cavity to solid cavity and re-design of the ejector pin proposed were derived after a detailed study & analysis conducted to arrive at these solutions. The solutions proposed have yield good results during the pilot run with zero (0) occurrence of resin bleed for 3 consecutive months.

Bio-phenolic resin from oil palm empty fruit bunches

Science.gov (United States)

Zakaria, Zuhaili; Zakaria, Sarani; Roslan, Rasidi; Chia, Chin Hua; Jaafar, Sharifah Nabihah Syed; Amran, Umar Adli

2018-04-01

Utilization of oil palm empty fruit bunches (EFB) in the production of bio-phenolic resin is an alternative way to reduce the dependency of petroleum-based phenol. In this study, resol type bio-phenolic resin (BPR) was synthesized from EFB fibers using sulfuric acid as the catalyst to produce liquefied empty fruit bunches (LEFB) followed by resinification reaction with formaldehyde in alkaline condition. The SEM image of LEFB residue showed separation of fiber bundles into individual fibers. This indicate that lignin was destroyed during the liquefaction process. The increased of formaldehyde/LEFB molar ratio has resulted an increase of viscosity, solid content and pH of the resin. The obtained FTIR spectra confirmed that functional groups of BPR resins was almost similar with commercial resin.

Treatment method for stabilization of radioactive exchange resin

International Nuclear Information System (INIS)

Hideo, Oni; Takashi, Miyake; Hitoshi, Miyamoto; Toshio, Funakoshi; Yuzo, Inagaki.

1988-01-01

This is a method for eluting radioactive nuclides from a radioactive ion exchange resin in which it has been absorbed. First, the Cs in this resin is extracted using a neutral salt solution which contains Na + . The Cs that has been transferred to the neutral salt solution is absorbed and expelled by inorganic ion exchangers. Then the Co, Fe, Mn and Sr in said resin are eluted using an acidic solution; the Co, Fe, Mn and Sr that have been transferred to the acidic solution are separated from that solution by means of a diffusion dialysis vat. This process is a unique characteristic of this ion exchange resin treatment method. 1 fig

Effect of organoclay incorporation on dental resin morphology

International Nuclear Information System (INIS)

Oliveira, Nadja M.S.; Reis, Romulo P.B.; Leite, Itamara F.; Morais, Crislene R.S.; Silva, Suedina M.L.

2009-01-01

The objective of the present work was to incorporate nanosilicates in commercial dental resins in order to prepare dental nanocomposites competitive as commercial nanoparticulates dental resins. Thus, a silicate, Cloisite 20A (C20A), was incorporated in a microhybrid dental resin (Z100) and morphological properties of the nanocomposites evaluated as a function of the incorporation method and the amount of filler employed. The samples were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The XRD results evidence that nanocomposites have been obtained and according to SEM results, the morphology of microhybrid resin was modified when C20A nanoparticulate was incorporated improve the size distribution and reduce the agglomeration of the particles. (author)

Evaluation of some anionic exchange resins as potential tablet ...

African Journals Online (AJOL)

The effect of resin concentration and compression force on the properties of tablets using the selected resin was investigated. In addition, the disintegrant efficacy of the selected resin in the tablet formulations containing either a basic drug, e.g., dextromethorphan hydrobromide (DMP), or an acidic drug, e.g., diclofenac ...

21 CFR 177.1340 - Ethylene-methyl acrylate copolymer resins.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Ethylene-methyl acrylate copolymer resins. 177.1340... Basic Components of Single and Repeated Use Food Contact Surfaces § 177.1340 Ethylene-methyl acrylate copolymer resins. Ethylene-methyl acrylate copolymer resins may be safely used as articles or components of...

21 CFR 872.3300 - Hydrophilic resin coating for dentures.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Hydrophilic resin coating for dentures. 872.3300... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3300 Hydrophilic resin coating for dentures. (a) Identification. A hydrophilic resin coating for dentures is a device that consists of a water...

21 CFR 872.3310 - Coating material for resin fillings.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Coating material for resin fillings. 872.3310... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3310 Coating material for resin fillings. (a) Identification. A coating material for resin fillings is a device intended to be applied to the...

Branched polymeric media: Perchlorate-selective resins from hyperbranched polyethyleneimine

KAUST Repository

Chen, Dennis P.

2012-10-02

Perchlorate (ClO4 -) is a persistent contaminant found in drinking groundwater sources in the United States. Ion exchange (IX) with selective and disposable resins based on cross-linked styrene divinylbenzene (STY-DVB) beads is currently the most commonly utilized process for removing low concentrations of ClO4 - (10-100 ppb) from contaminated drinking water sources. However, due to the low exchange capacity of perchlorate-selective STY-DVB resins (∼0.5-0.8 eq/L), the overall cost becomes prohibitive when treating groundwater with higher concentration of ClO4 - (e.g., 100-1000 ppb). In this article, we describe a new perchlorate-selective resin with high exchange capacity. This new resin was prepared by alkylation of branched polyethyleneimine (PEI) beads obtained from an inverse suspension polymerization process. Batch and column studies show that our new PEI resin with mixed hexyl/ethyl quaternary ammonium chloride exchange sites can selectively extract trace amounts of ClO4 - from a makeup groundwater (to below detection limit) in the presence of competing ions. In addition, this resin has a strong-base exchange capacity of 1.4 eq/L, which is 1.75-2.33 times larger than those of commercial perchlorate-selective STY-DVB resins. The overall results of our studies suggest that branched PEI beads provide versatile and promising building blocks for the preparation of perchlorate-selective resins with high exchange capacity. © 2012 American Chemical Society.

A randomized controlled three year evaluation of "bulk-filled" posterior resin restorations based on stress decreasing resin technology

DEFF Research Database (Denmark)

van Dijken, Jan W V; Pallesen, Ulla

2014-01-01

-hybrid resin composite (Ceram X mono) layer. In the second cavity, the hybrid resin composite was placed in 2mm increments. The restorations were evaluated using slightly modified USPHS criteria at baseline and then yearly during 3 years. Caries risk and parafunctional habits of the participants were estimated...

Primary study on synthesis and characterization of the new type EB curable resins. Pt.1: Acrylic resins modified by light-oil

International Nuclear Information System (INIS)

Wei Jinshan; Yi Min; Wang Ruiyu; Li Jun; Ha Hongfei

1995-01-01

An acrylic resin modified by vegetable oil with high degree of unsaturation level has been synthesized. The characterization of coating film EB cured by the modified acrylic resin was studied primarily. The new type of EB curable acrylic resin is possessed of many merits such as cheap raw materials, simple synthesis technique and pretty characteristics of coating film. It is especially fit for timber surface coatings cured by EB radiation

21 CFR 872.3770 - Temporary crown and bridge resin.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Temporary crown and bridge resin. 872.3770 Section... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3770 Temporary crown and bridge resin. (a) Identification. A temporary crown and bridge resin is a device composed of a material, such as...

21 CFR 177.2410 - Phenolic resins in molded articles.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Phenolic resins in molded articles. 177.2410... as Components of Articles Intended for Repeated Use § 177.2410 Phenolic resins in molded articles. Phenolic resins identified in this section may be safely used as the food-contact surface of molded...

Incineration of spent ion exchange resin

International Nuclear Information System (INIS)

Hasegawa, Chiaki

1990-01-01

It is a pressing need to reduce radioactive waste which is generated from the maintenance and operation of a nuclear power plant. Incineration of low level combustible solid waste such as polyethylene seats, paper and others have been successfully performed since 1984 at the Shimane Nuclear Power Station. Furthermore, for extending incineration treatment to spent ion exchange resin, the incineration test was carried out in 1989. However, as the cation exchange resin contains sulfur and then incineration generates SOx gases, so the components of this facility will be in a corrosive environment. We surveyed incineration conditions to improve the corrosive environment at the exhaust gas treatment system. This paper includes these test results and improved method to incinerate spent ion exchange resin. (author)

21 CFR 177.2415 - Poly(aryletherketone) resins.

Science.gov (United States)

2010-04-01

... 12,000, as determined by gel permeation chromatography in comparison with polystyrene standards, and... calorimetry. (b) Optional adjuvant substances. The basic resins identified in paragraph (a) may contain... percent by weight as a residual solvent in the finished basic resin. (c) Extractive limitations. The...

Study on the Novel Dicyanate Ester Resin Containing Naphthalene Unit

Institute of Scientific and Technical Information of China (English)

Hong Qiang YAN; Hong Yun PENG; Li JI; Guo Rong QI

2004-01-01

The novel dicyanate ester resin containing naphthalene unit (DNCY) was synthesized, and characterized by FT-IR, 1H-NMR, 13C-NMR and elemental analysis (EA).The thermal properties of DNCY resin was studied by thermal degradation analysis at a heating rate of 10 (C /min-1 in N2 and air. The DNCY resin exhibited better thermal and thermal-oxidative stability than bisphenol A dicyanate (BACY) resin.

Evaluating resin-enamel bonds by microshear and microtensile bond strength tests: effects of composite resin

Directory of Open Access Journals (Sweden)

Andrea Mello de Andrade

2010-12-01

Full Text Available OBJECTIVES: The aims of this study were to evaluate the effect of resin composite (Filtek Z250 and Filtek Flow Z350 and adhesive system [(Solobond Plus, Futurabond NR (VOCO and Adper Single Bond (3M ESPE] on the microtensile (μTBS and microshear bond strength (μSBS tests on enamel, and to correlate the bond strength means between them. MATERIAL AND METHODS: Thirty-six extracted human molars were sectioned to obtain two tooth halves: one for μTBS and the other one for μSBS. Adhesive systems and resin composites were applied to the enamel ground surfaces and light-cured. After storage (37(0C/24 h specimens were stressed (0.5 mm/min. Fracture modes were analyzed under scanning electron microscopy. The data were analyzed using two-way ANOVA and Tukey's test (α=0.05. RESULTS: The correlation between tests was estimated with Pearson's product-moment correlation statistics (α =0.05. For both tests only the main factor resin composite was statistically significant (p<0.05. The correlation test detected a positive (r=0.91 and significant (p=0.01 correlation between the tests. CONCLUSIONS: The results were more influenced by the resin type than by the adhesives. Both microbond tests seem to be positive and linearly correlated and can therefore lead to similar conclusions.

Feature Selection with Conjunctions of Decision Stumps and Learning from Microarray Data.

Science.gov (United States)

Shah, M; Marchand, M; Corbeil, J

2012-01-01

One of the objectives of designing feature selection learning algorithms is to obtain classifiers that depend on a small number of attributes and have verifiable future performance guarantees. There are few, if any, approaches that successfully address the two goals simultaneously. To the best of our knowledge, such algorithms that give theoretical bounds on the future performance have not been proposed so far in the context of the classification of gene expression data. In this work, we investigate the premise of learning a conjunction (or disjunction) of decision stumps in Occam's Razor, Sample Compression, and PAC-Bayes learning settings for identifying a small subset of attributes that can be used to perform reliable classification tasks. We apply the proposed approaches for gene identification from DNA microarray data and compare our results to those of the well-known successful approaches proposed for the task. We show that our algorithm not only finds hypotheses with a much smaller number of genes while giving competitive classification accuracy but also having tight risk guarantees on future performance, unlike other approaches. The proposed approaches are general and extensible in terms of both designing novel algorithms and application to other domains.

Immobilisation of ion exchange resins in cement

International Nuclear Information System (INIS)

Howard, C.G.; Jolliffe, C.B.; Lee, D.J.

1990-09-01

The removal of activity from spent decontaminating solutions eg LOMI can be achieved using organic ion exchange resins. These resins can be successfully immobilised in cement based matrices. The optimum cement system contained 10% ordinary Portland cement 84% gg blast furnace slag, 6% microsilica with a water cement ratio of 0.5 and a dry resin loading of 36% with respect to total weight. This formulation was successfully scaled up to 200 litres giving a product with acceptable compressive strength, dimensional stability and elastic modulus. Storage of samples under water appears to have no detrimental effects on the product's properties. (author)

Immobilisation of ion exchange resins in cement

International Nuclear Information System (INIS)

Howard, C.G.; Jolliffe, C.B.; Lee, D.J.

1990-09-01

The removal of activity from spent decontaminating solutions eg LOMI can be achieved using organic ion exchange resins. These resins can be successfully immobilised in cement based matrices. The optimum cement system contained 10% ordinary Portland cement, 84% gg blast furnace slag, 6% microsilica with a water cement ratio of 0.5 and a dry resin loading of 36% with respect to total weight. This formulation was successfully scaled up to 200 litres giving a product with acceptable compressive strength, dimensional stability and elastic modulus. Storage of samples under water appears to have no detrimental effects on the products' properties. (author)

Modeling and mechanical performance of carbon nanotube/epoxy resin composites

International Nuclear Information System (INIS)

Srivastava, Vijay Kumar

2012-01-01

Highlights: ► The MWCNT fillers are uniformly dispersed in the epoxy resin, which improved the mechanical properties of epoxy resin. ► Modified Halpin–Tsai model is useful to calculate the Young’s modulus of MWCNT/epoxy resin composite. ► The experimental moduli are within the variation of 27% with the theoretical values. -- Abstract: The effect of multi-walled carbon nanotube (MWCNT) addition on mechanical properties of epoxy resin was investigated to obtain the tensile strength, compressive strength and Young’s modulus from load versus displacement graphs. The result shows that the tensile strength, compressive strength and Young’s modulus of epoxy resin were increased with the addition of MWCNT fillers. The significant improvements in tensile strength, compressive strength and Young’s modulus were obtained due to the excellent dispersion of MWCNT fillers in the epoxy resin. The dispersion of MWCNT fillers in epoxy resin was observed by scanning electron microscopy (SEM) and transmission electron microscopy (TEM) analysis. Also, Halpin–Tsai model was modified by considering the average diameter of internal/external of multi-walled nanotube and orientation factor (α) to calculate the Young’s modulus of multi-walled carbon nanotubes (MWCNTs)/epoxy resin composite. There was a good correlation between the experimentally obtained Young’s modulus and modified Halpin–Tsai model.

Development of radiation-curable resin based on natural rubber

Energy Technology Data Exchange (ETDEWEB)

Mohd, Dahlan; Harun, Abdul Ghani [Nuclear Energy Unit, Bangi, Selangor (Malaysia)

1994-12-31

A new radiation curable resin based on natural rubber has been developed. The resin was based on the reaction between low molecular weight epoxidised natural rubber and acrylic acid. When formulated with reactive monomers and photoinitiator, it solidified upon irradiation with UV light. The resin may find applications in coating for cellulosic-based substrates and pressure-sensitive adhesive.

Development of radiation-curable resin based on natural rubber

International Nuclear Information System (INIS)

Dahlan Mohd; Abdul Ghani Harun

1993-01-01

A new radiation curable resin based on natural rubber has been developed. The resin was based on the reaction between low molecular weight epoxidised natural rubber and acrylic acid. When formulated with reactive monomers and photoinitiator, it solidified upon irradiation with UV light. The resin may find applications in coating for cellulosic-based substrates and pressure-sensitive adhesive

Dsc cure kinetics of an unsaturated polyester resin using empirical kinetic model

International Nuclear Information System (INIS)

Abdullah, I.

2015-01-01

In this paper, the kinetics of curing of unsaturated polyester resin initiated with benzoyl peroxide was studied. In case of unsaturated polyester (UP) resin, isothermal test alone could not predict correctly the curing time of UP resin. Therefore, isothermal kinetic analysis through isoconventional adjustment was used to correctly predict the curing time and temperature of UP resin. Isothermal kinetic analysis through isoconversional adjustment indicated that 97% of UP resin cures in 33 min at 120 degree C. Curing of UP resin through microwaves was also studied and found that 67% of UP resin cures in 1 min at 120 degree C. The crosslinking reaction of UP resin is so fast at 120 degree C that it becomes impossible to predict correctly the curing time of UP resin using isothermal test and the burial of C=C bonds in microgels makes it impossible to be fully cured by microwaves at 120 degree C. The rheological behaviour of unsaturated polyester resin was also studied to observe the change in viscosity with respect to time and temperature. (author)

Measurements of volatile compound contents in resins using a moisture analyzer.

Science.gov (United States)

Hashimoto, Masanori; Nagano, Futami; Endo, Kazuhiko; Ohno, Hiroki

2010-02-01

The contents of volatile adhesive compounds, such as water, solvents, and residual unpolymerized monomers, affect the integrity and durability of adhesive bonding. However, there is no method available that can be used to rapidly assess the residual solvent or water contents of adhesive resins. This study examined the effectiveness of a digital moisture analyzer to measure the volatile compound contents of resins. Five self-etching adhesives and seven experimental light-cured resins prepared with different contents (0, 10, and 20% by weight) of water or solvents (acetone and ethanol) were examined in this study. The resins were prepared using different methods (with and without air blast or light-curing) to simulate the clinical conditions of adhesive application. Resin weight changes (% of weight loss) were determined as the residual volatile compound contents, using the moisture analyzer. After the measurements, the resin films were examined using a scanning electron microscope. The weight changes of the resins were found to depend on the amount of water or solvents evaporating from the resin. Water and solvents were evaporated by air blast or light-curing, but some of the water and solvents remained in the cured resin. The moisture analyzer is easy to operate and is a useful instrument for using to measure the residual volatile compound contents of adhesive resin.

Studies on chemoviscosity modeling for thermosetting resins

Science.gov (United States)

Bai, J. M.; Hou, T. H.; Tiwari, S. N.

1987-01-01

A new analytical model for simulating chemoviscosity of thermosetting resins has been formulated. The model is developed by modifying the well-established Williams-Landel-Ferry (WLF) theory in polymer rheology for thermoplastic materials. By introducing a relationship between the glass transition temperature Tg(t) and the degree of cure alpha(t) of the resin system under cure, the WLF theory can be modified to account for the factor of reaction time. Temperature dependent functions of the modified WLF theory constants C sub 1 (t) and C sub 2 (t) were determined from the isothermal cure data. Theoretical predictions of the model for the resin under dynamic heating cure cycles were shown to compare favorably with the experimental data. This work represents progress toward establishing a chemoviscosity model which is capable of not only describing viscosity profiles accurately under various cure cycles, but also correlating viscosity data to the changes of physical properties associated with the structural transformation of the thermosetting resin systems during cure.

Effects of resin content and preparing conditions on the properties of polyphenylene sulfide resin/graphite composite for bipolar plate

Energy Technology Data Exchange (ETDEWEB)

Xia, Li-gang; Li, Ai-ju; Yin, Qiang [Key Laboratory for Liquid Structure and Heredity of Materials, Ministry of Education, Shandong University, Shandong Key Laboratory of Engineering Ceramics, Shandong University, Jinan 250061 (China); Wang, Wei-qiang [School of Mechanical Engineering, Shandong University, Jinan 250061 (China); Lin, Heng; Zhao, Yi-bo [School of Material Science and Engineering, Shandong University, Jinan 250061 (China)

2008-03-15

In the paper, a kind of polyphenylene sulfide (PPS) resin/graphite (G) composite for bipolar plate was prepared by using the PPS resin as adhesive and simple hot pressing. The influences of the resin content, the molding temperature and holding time on the conductivity and the bending strength of the PPS/G composite bipolar plate were investigated firstly and then the optimum content and the preparing conditions of the composite were obtained. The experimental results show that the electrical conductivity decreases and the bending strength reveals a serrated variation with increase in PPS resin content; when the holding time is certain, the conductivity decreases and the bending strength increases with the molding temperature increasing. The experimental results further show that the effect of the holding time on the properties of the composite is different at different molding temperatures. The PPS/G composite with 20% PPS resin content has electrical conductivity of 118.9 S cm{sup -1} and bending strength of 52.4 MPa when it molded at 380 C for 30 min, and has electrical conductivity of 105 S cm{sup -1}, bending strength of 55.7 MPa when it molded at 390 C for 30 min. The properties of the composites can meet the requirements of United States Department of Energy (DOE). (author)

Dissolution of ion exchange resin by hydrogen peroxide

International Nuclear Information System (INIS)

Lee, S.C.

1981-08-01

The resin dissolution process was conducted successfully in full-scale equipment at the SRL Semiworks. A solution containing 0.001M Fe 2+ , or Fe 3+ , and 3 vol % H 2 O 2 in 0.1M HNO 3 is sufficient to dissolve up to 40 vol % resin slurry (Dowex 50W-X8). Foaming and pressurization can be eliminated by maintaining the dissolution temperature below 99 0 C. The recommended dissolution temperature range is 85 to 90 0 C. Premixing hydrogen peroxide with all reactants will not create a safety hazard, but operating with a continual feed of hydrogen peroxide is recommended to control the dissolution rate. An air sparging rate of 1.0 to 1.5 scfm will provide sufficient mixing. Spent resin from chemical separation contains DTPA (diethylenetriaminepentaacetic acid) residue, and the resin must be washed with 0.1M NH 4 OH to remove excess DTPA before dissolution. Gamma irradiation of resin up to 4 kW-hr/L did not change the dissolution rate significantly

Development of new and improved polymer matrix resin systems, phase 1

Science.gov (United States)

Hsu, M. S.

1983-01-01

Vinystilbazole (vinylstryrylpyridine) and vinylpolystyrulpyridine were prepared for the purpose of modifying bismaleimide composite resins. Cure studies of resins systems were investigated by differential scanning calorimetry. The vinylstyrylpyridine-modified bismaleimide composite resins were found to have lower cure and gel temperatures, and shorter cure times than the corresponding unmodified composite resins. The resin systems were reinforced with commercially avialable satin-weave carbon cloth. Prepregs were fabricated by solvent or hot melt techniques. Thermal stability, flammability, moisture absorption, and mechanical properties of the composites (such as flexural strength, modulus, tensile and short beam shear strength) were determined. Composite laminates showed substantial improvements in both processability and mechanical properties compared to he bismaleimide control systems. The vinylstyrylpyridine modified bismaleimide resins can be used as advanced matrix resins for graphite secondary structures where ease of processing, fireworthiness, and high temperature stability are required for aerospace applications.

PASTAS ESTIMULANTES EM SISTEMAS DE RESINAGEM DE Pinus elliottii var. elliottii

Directory of Open Access Journals (Sweden)

André Luiz Marretto Fusatto

2013-01-01

Full Text Available The use of stimulating pastes aims to increase the rate of resin flow and its time of duration. In the Forest Experiment Station of Itatinga, São Paulo state, 159 trees of Pinus elliottii var. elliottii were were submitted to the treatments with 5 stimulant pastes, (Red Alchem, Paste with Ethephon Planebrás, Black Resin Brazil, Red Eldorado and Test Paste (Paraquat + Ethephon that was compared to the Control (Black Planebrás. Biweekly chipping and collects every three months were accomplished (from the result of 5 grooves, being determined the resin weight during 2.5 years. The application of stimulating pastes with ethephon did not show significant advantage about application of pastes without ethephon. The stimulant pastes applied were different in the weightings performed. In the treatments applied, the percentage of pitch ranged from 71.33% to 76.56% and the turpentine ranged from 10.37% to 13.78%. The yield of alpha-pinene ranged from 37.70% to 53.31%, and of beta-pinene from 34.34% to 50.41%.

Chromatographic separation process with pellicular ion exchange resins that can be used for ion or isotope separation and resins used in this process

International Nuclear Information System (INIS)

Carles, M.; Neige, R.; Niemann, C.; Michel, A.; Bert, M.; Bodrero, S.; Guyot, A.

1989-01-01

For separation of uranium, boron or nitrogen isotopes, an isotopic exchange is carried out betwen an isotope fixed on an ion exchange resin and another isotope of the same element in the liquid phase contacting the resin. Pellicular resins are used comprising composite particulates with an inert polymeric core and a surface layer with ion exchange groups [fr

Incineration of ion-exchange resins in fluidized bed. Part of a coordinated programme on treatment of spent ion exchange resins

International Nuclear Information System (INIS)

Valkianinen, M.

1980-10-01

Incineration of ion-exchange resins in a fluidized bed was studied on the pilot plant scale. The test programme performed consisted of the testing of various bed materials and finding the optimal conditions of incineration of spent resins. Granular resins were incinerated in an ethanol-water mixture. Incinernation converts the organic resin into inert oxide material, which can be solidified for instance with cement. The weight of the ash was 1...20% and the volume 2...30% of the original resins, which contained 15...25% moisture. When solidified with cement the volume of the ash-concrete is 4...22% of the concrete of equal compressive strength acquired by direct solidification. Water immersion and heat tests of solidified ash showed satisfactory results. The absorption of Cs and Co in various bed materials was studied by means of inactive tracer materials. Biotite and chamotte absorbed significantly, but this absorption does not drastically help on the off gas side. The sintering of the bed materials in the presence of sodium was studied. Corundum, chamotte and biotite have a safety limit of 5% sodium of the bed's weight at 850 0 C

21 CFR 177.2450 - Polyamide-imide resins.

Science.gov (United States)

2010-04-01

... Components of Articles Intended for Repeated Use § 177.2450 Polyamide-imide resins. Polyamide-imide resins identified in paragraph (a) of this section may be safely used as components of articles intended for... Safety and Applied Nutrition (HFS-200), Food and Drug Administration, 5100 Paint Branch Pkwy., College...

Thermosetting resins for nuclear track detection

International Nuclear Information System (INIS)

Fujii, M.; Yokota, R.

1986-01-01

Several new thermosetting resins with a three dimensional network structure similar to that of CR-39 were polymerized to study their characteristics as nuclear track detectors. The comparison of the molecular structures of these resins gives us an important clue to develop highly sensitive polymeric track detectors. For example, butanediol bis allylcarbonate (BuAC) shows the sensitivity about ten times higher than diallyl and adipate (DAA). This suggests the carbonate groups in the BuAC molecule provide a much higher sensitivity than the ester groups in the DAA. During the course of this study, thermosetting resins with good etching properties and various sensitivities have been developed. Though the sensitivity of DAA is low, it will be useful for observations of ultra heavy cosmic rays and heavily ionizing particles at low energies. (author)

75 FR 67105 - Granular Polytetrafluoroethylene Resin From Italy and Japan

Science.gov (United States)

2010-11-01

... Polytetrafluoroethylene Resin From Italy and Japan AGENCY: United States International Trade Commission. ACTION... resin from Italy and Japan. SUMMARY: The Commission hereby gives notice that it has instituted reviews... revocation of the antidumping duty orders on granular polytetrafluoroethylene resin from Italy and Japan...

Structure-to-property relationships in addition cured polymers. II - Resin Tg and composite initial mechanical properties of norbornenyl cured polyimide resins

Science.gov (United States)

Alston, William B.

1986-01-01

PRM (polymerization of monomeric reactants) methodology was used to prepare thirty different polyimide oligomeric resins. Monomeric composition as well as chain length between sites of crosslinks were varied to examine their effects on glass transition temperature (Tg) of the cured/postcured resins. An almost linear correlation of Tg versus molecular distance between the crosslinks was observed. An attempt was made to correlate Tg with initial mechanical properties (flexural strength and interlaminar shear strength) of unidirectional graphite fiber composites prepared with these resins. However, the scatter in mechanical strength data prevented obtaining as clear a correlation as was observed for the structural modification/crosslink distance versus Tg. Instead, only a range of composite mechanical properties was obtained at the test temperatures studied (room temperature, 288 and 316 C). Perhaps more importantly, what did become apparent during the attempted correlation study was: (1) that PMR methodology could be used to prepare composites from resins that contain a wide variety of monomer modifications, and (2) that these composites almost invariably provided satisfactory initial mechanical properties as long as the resins selected were melt processable.

Diclofenac removal in urine using strong-base anion exchange polymer resins.

Science.gov (United States)

Landry, Kelly A; Boyer, Treavor H

2013-11-01

One of the major sources of pharmaceuticals in the environment is wastewater effluent of which human urine contributes the majority of pharmaceuticals. Urine source separation has the potential to isolate pharmaceuticals at a higher concentration for efficient removal as well as produce a nutrient byproduct. This research investigated the efficacy of using strong-base anion exchange polymer resins to remove the widely detected and abundant pharmaceutical, diclofenac, from synthetic human urine under fresh and ureolyzed conditions. The majority of experiments were conducted using a strong-base, macroporous, polystyrene resin (Purolite A520E). Ion-exchange followed a two-step removal rate with rapid removal in 1 h and equilibrium removal in 24 h. Diclofenac removal was >90% at a resin dose of 8 mL/L in both fresh and ureolyzed urine. Sorption of diclofenac onto A520E resin was concurrent with desorption of an equivalent amount of chloride, which indicates the ion-exchange mechanism is occurring. The presence of competing ions such as phosphate and citrate did not significantly impact diclofenac removal. Comparisons of three polystyrene resins (A520E, Dowex 22, Dowex Marathon 11) as well as one polyacrylic resin (IRA958) were conducted to determine the major interactions between anion exchange resin and diclofenac. The results showed that polystyrene resins provide the highest level of diclofenac removal due to electrostatic interactions between quaternary ammonium functional groups of resin and carboxylic acid of diclofenac and non-electrostatic interactions between resin matrix and benzene rings of diclofenac. Diclofenac was effectively desorbed from A520E resin using a regeneration solution that contained 4.5% (m/m) NaCl in an equal-volume mixture of methanol and water. The greater regeneration efficiency of the NaCl/methanol-water mixture over the aqueous NaCl solution supports the importance of non-electrostatic interactions between resin matrix and benzene rings

Design of systems for handling radioactive ion exchange resin beads

International Nuclear Information System (INIS)

Shapiro, S.A.; Story, G.L.

1979-01-01

The flow of slurries in pipes is a complex phenomenon. There are little slurry data available on which to base the design of systems for radioactive ion exchange resin beads and, as a result, the designs vary markedly in operating plants. With several plants on-line, the opportunity now exists to evaluate the designs of systems handling high activity spent resin beads. Results of testing at Robbins and Meyers Pump Division to quantify the behavior of resin bead slurries are presented. These tests evaluated the following slurry parameters; resin slurry velocity, pressure drop, bead degradation, and slurry concentration effects. A discussion of the general characteristics of resin bead slurries is presented along with a correlation to enable the designer to establish the proper flowrate for a given slurry composition and flow regime as a function of line size. Guidelines to follow in designing a resin handling system are presented

Perlekatan koloni Streptococcus mutans pada permukaan resin komposit sinar tampak (The adherence of Streptococcus mutans colony to surface visible light composite resins

Directory of Open Access Journals (Sweden)

Ajeng Anggraeni

2005-03-01

Full Text Available Visible light composite resins was used to restore anterior and posterior teeth, and it is always covered by saliva pellicle. S. mutans can adhere to all of the surface of oral cavity and visible light composite resins. The aim of this study was to know the amount of S. mutans colony adherence to visible light composite resins surface. The sample of 5 mm diameter and 3 mm in thickness was immersed in saliva for one hour, than the samples were put into bacteria suspension, incubated for 24 hours at 37° C. The amount of S. mutans was determined by direct count using microscope. The data were statistically analyzed by using t test. The result showed a significance difference of S. mutans colony between hybrid and micro fill visible light composite resins. The conclusion was that the amount of S. mutans adherence on the surface of hybrid was higher than the micro fill visible light composite resins.

Development of amino resin for paint formulation: Copolymerization ...

African Journals Online (AJOL)

SERVER

2007-06-18

Jun 18, 2007 ... IR spectroscopy and macro phase separation techniques. At a given TEA ... form aldehyde emission from urea formaldehyde resin through one step ..... of resin molecules (Barminas and Osemeahon, 2007;. Sekaran et al.

Immobilization of ion-exchange resins in cement

International Nuclear Information System (INIS)

Howard, C.G.; Jolliffe, C.B.; Lee, D.J.

1991-01-01

The removal of activity from spent decontaminating solutions, can be achieved using organic ion-exchange resins. These resins can be successfully immobilized in cement-based matrices. The optimum cement system contained 10% ordinary Portland cement, 84% gg blast furnace slag, 6% microsilica with a water/cement ratio of 0.5 and a dry resin loading of 36% with respect to total weight. This formulation was successfully scaled up to 200 litres, giving a product with acceptable compressive strength, dimensional stability and elastic modulus. Storage of samples under water appears to have no detrimental effects on the product's properties. 26 tabs., 22 figs., 29 refs

Color change of composite resins subjected to accelerated artificial aging.

Science.gov (United States)

Tornavoi, Denise Cremonezzi; Agnelli, José Augusto Marcondes; Panzeri, Heitor; Dos Reis, Andréa Cândido

2013-01-01

The aim of this study was to evaluate the influence of accelerated artificial aging (AAA) on the color change of composite resins used in dentistry. Three composite resins were evaluated: Two microhybrids and one hybrid of higher viscosity, with different amounts and sizes of filler particles, shades C2 and B2. A total of 54 specimens were obtained (18 for each composite resin), made of a Teflon matrix (15 mm in diameter and 2 mm in height). The color measurements were obtained with a Spectrophotometer, (PCB 6807 BYK Gardner) before and after AAA. Data were submitted to the Kolmogorov-Smirnov test (α >0.05), ANOVA and Tukey test (α 3). Considering the variable ∆E, it was observed that the color tone C2 was already statistically different for the microhybrid composite resin prior to AAA (P aging the composite resin hybrid of higher viscosity B2 showed the highest color variation rate and microhybrid with zirconium/silica C2 showed the lowest. All composite resins presented unacceptable color changes after 382 h of aging and different composite resins with same hue, presented different colors before being subjected to the aging process (B2 and C2) and after (B2). It was also observed color difference within a group of the same composite resin and same hue.

Effect of photoactivation on the reduction of composite resin contamination.

Science.gov (United States)

Pauletti, Natalia A; Girotto, Luiza P S; Leite, Françoise H S; Mario, Débora N

2017-06-01

Composite resins are predominantly marketed in developing countries in tube form, and the contents of the tube may be used in numerous procedures for different patients. This represents a problem because of the risk of cross-contamination. This study aimed to evaluate contamination in vitro of the internal contents of composite resin tubes in the dental clinics of a higher-education institution, as well as the effect of photoactivation on the level of contamination. Twenty-five tubes containing composite resin were randomly chosen (by lottery). From each tube, two samples of approximately 2 mm of composite resin were removed, and then one sample, but not the other, was photoactivated. These samples were plated on Brain-Heart Infusion (BHI), Sabouraud and MacConkey agars, and the plates were incubated at 37°C for 24-48 h. Colony counting and Gram staining were performed for subsequent microscopic identification of fungi and bacteria. The non-photoactivated composite resin group presented significantly higher microbial contamination in relation to the photoactivated composite resin group. The photoactivation of camphorquinone present in composite resin produces reactive oxygen species, which might promote cell death of contaminant microorganisms. Thus, although the same tube of composite resin may be used for a number of different patients in the dental clinics of developing countries, the photoactivation process potentially reduces the risk of cross-contamination. © 2017 Eur J Oral Sci.

Future perspectives of resin-based dental materials.

Science.gov (United States)

Jandt, Klaus D; Sigusch, Bernd W

2009-08-01

This concise review and outlook paper gives a view of selected potential future developments in the area of resin-based biomaterials with an emphasis on dental composites. A selection of key publications (1 book, 35 scientific original publications and 1 website source) covering the areas nanotechnology, antimicrobial materials, stimuli responsive materials, self-repairing materials and materials for tissue engineering with direct or indirect relations and/or implications to resin-based dental materials is critically reviewed and discussed. Connections between these fields and their potential for resin-based dental materials are highlighted and put in perspective. The need to improve shrinkage properties and wear resistance is obvious for dental composites, and a vast number of attempts have been made to accomplish these aims. Future resin-based materials may be further improved in this respect if, for example nanotechnology is applied. Dental composites may, however, reach a completely new quality by utilizing new trends from materials science, such as introducing nanostructures, antimicrobial properties, stimuli responsive capabilities, the ability to promote tissue regeneration or repair of dental tissues if the composites were able to repair themselves. This paper shows selected potential future developments in the area of resin-based dental materials, gives basic and industrial researchers in dental materials science, and dental practitioners a glance into the potential future of these materials, and should stimulate discussion about needs and future developments in the area.

Change of color in resins by adding layers of color 'enamel'

International Nuclear Information System (INIS)

Lafuente Marin, David; Arce Navarro, Hilda

2007-01-01

The quantification of the color change is proposed at the time of employing enamel resin over dentine resin. Six resins color dentin and two color enamel were used. Five discs of resin were built of each resin, with a deameter of 10 mm and a thicjness of 2 mm. The reflectance spectrophotometer Color-Eye ® 7000-A were used, to obtain the values L*, a*, b* of the dentin resin disks and transposition of these with enamel. The conclusion has been that in the color have produced changes clinically detectable when put layers of enamel. The Resin Helio Fill Transparent has been which has produced major changes. Given the two enamel resins, dentin resin Helio Molar 310/B3 has been which has suffered major changes and Helio Fill A2 which has introduced fewer changes. Most resins have decreased the chroma, less the value. (author) [es

Synthesis and Thermal Properties of a Novel Nitrogen-containing Epoxy Resin

Institute of Scientific and Technical Information of China (English)

Xing Hong ZHANG; Hong Mei WAN; Yu Qin MIN; Zuo FANG; Guo Rong QI

2005-01-01

A new nitrogen-containing epoxy resin (XT resin) was synthesized from chain extension of xylenephenolformaldehyde resin (XPF) and triglycidyl isocyanurate (TGIC) in the presence of base catalyst. FT-IR and 1H-NMR analysis confirmed the chemical structure of XT resin. It was cured with dicyandiamide (DICY) and diaminodiphenyl sulfone (DDS). Dynamic mechanical analysis (DMA) results showed that the introduction of triazine ring provides epoxy polymer with good thermal stability. Furthermore, high char yields at 800℃ in thermogravimetric (TGA)analysis indicated that XT resin had potential flame retardance.

Maleimido substituted cyclotriphosphazene resins for fire and heat resistant composites

Science.gov (United States)

Kumar, D.; Fohlen, G. M.; Parker, J. A.

1983-01-01

A new class of fire- and heat-resistant matrix resins have been synthesized by the thermal polymerization of maleimido substituted phenoxycyclotriphosphazenes. The resins have exhibited a char yield of 82 percent at 800 C in nitrogen and 81 percent at 700 C in air. Graphite-fabric laminates based on a resin of this class have shown a limiting oxygen index of 100 percent even at 300 C. Details of the fabrication of the resins and the composites and testing procedures are discussed.

Recovery of tretrachloroaurate through ion exchange with Dowex 11 resin

International Nuclear Information System (INIS)

Alguacil, F.J.

1998-01-01

The recovery of the tretrachloroaurate complex by the anionic ion exchange resin Dowex 11 has been studied. The kinetics of gold adsorption were dependent of both gold and resin concentrations and temperature. The adsorption isotherm can be described by the expression Q=kC''n. The loaded resin could be eluted by an acidic thiourea solution at 20 degree centigree. After several adsorption-elution cycles there is not any apparent loss in the adsorption properties of the resin. (Author) 6 refs

Clinical performance of a hybrid resin composite with and without an intermediate layer of flowable resin composite: a 7-year evaluation

DEFF Research Database (Denmark)

van Dijken, Jan W V; Pallesen, Ulla

2011-01-01

The objective of this prospective clinical follow up was to evaluate the long term clinical performance of a hybrid resin composite in Class II restorations with and without intermediate layer of flowable resin composite....

Modified ion exchange resins - synthesis and properties. Pt. 1

Energy Technology Data Exchange (ETDEWEB)

Doescher, F.; Klein, J.; Pohl, F.; Widdecke, H.

1982-01-22

Sulfomethylated resins are prepared by polymer analogous reactions, starting from macroporous poly(styrene-co-divinylbenzene) matrices. Different reaction paths are discussed and used in the synthesis. Sulfomethylation can be achieved by reaction of a chloromethylated resin with dimethyl sulfide and sodium sulfonate or alternatively by oxidation of polymer-bound thiol groups. Both methods give high conversions as shown by IR spectra and titration of the sulfonic acid groups. Poly(1-(4-hydroxysulfomethylphenyl)ethylene) (3) is obtained by reaction of poly(1-(4-hydroxyphenyl)ethylene) (2) resin with formaldehyde/sodium sulfonate. The thermal stability, catalytic activity, and ion exchange equilibria of the sulfomethylated resin are investigated.

In vitro enamel remineralization capacity of composite resins containing sodium trimetaphosphate and fluoride.

Science.gov (United States)

Tiveron, Adelisa Rodolfo Ferreira; Delbem, Alberto Carlos Botazzo; Gaban, Gabriel; Sassaki, Kikue Takebayashi; Pedrini, Denise

2015-11-01

This study evaluated the in vitro enamel remineralization capacity of experimental composite resins containing sodium trimetaphosphate (TMP) combined or not with fluoride (F). Bovine enamel slabs were selected upon analysis of initial surface hardness (SH1) and after induction of artificial carious lesions (SH2). Experimental resins were as follows: resin C (control—no sodium fluoride (NaF) or TMP), resin F (with 1.6% NaF), resin TMP (with 14.1% TMP), and resin TMP/F (with NaF and TMP). Resin samples were made and attached to enamel slabs (n = 12 slabs per material). Those specimens (resin/enamel slab) were subjected to pH cycling to promote remineralization, and then final surface hardness (SH3) was measured to calculate the percentage of surface hardness recovery (%SH). The integrated recovery of subsurface hardness (ΔKHN) and F concentration in enamel were also determined. Data was analyzed by ANOVA and Student-Newman-Keuls test (p Resins F and TMP/F showed similar SH3 values (p = 0.478) and %SH (p = 0.336) and differed significantly from the other resins (p resin TMP/F presented the lowest area of lesion (p resins (p = 0.042), but higher than in the other resins (p composite resin enhanced its capacity for remineralization of enamel in vitro. The combination of two agents with action on enamel favored remineralization, suggesting that composite resins containing sodium trimetaphosphate and fluoride could be indicated for clinical procedures in situations with higher cariogenic challenges.

Assessment of surface hardness of acrylic resins submitted to accelerated artificial aging.

Science.gov (United States)

Tornavoi, D C; Agnelli, J A M; Lepri, C P; Mazzetto, M O; Botelho, A L; Soares, R G; Dos Reis, A C

2012-06-01

The aim of this study was to assess the influence of accelerated artificial aging (AAA) on the surface hardness of acrylic resins. The following three commercial brands of acrylic resins were tested: Vipi Flash (autopolymerized resin), Vipi Wave (microwave heat-polymerized resin) and Vipi Cril (conventional heat-polymerized resin). To perform the tests, 21 test specimens (65x10x3 mm) were made, 7 for each resin. Three surface hardness readings were performed for each test specimen, before and after AAA, and the means were submitted to the following tests: Kolmogorov-Smirnov (P>0.05), Levene Statistic, Two-way ANOVA, Tukey Post Hoc (Paging, the autopolymerized acrylic resin Vipi Flash showed lower hardness values when compared with the heat-polymerized resin Vipi Cril (P=0.001). After aging, the 3 materials showed similar performance when compared among them. The Vipi Cril was the only one affected by AAA and showed lower hardness values after this procedure (Pp=0.003). It may be concluded that accelerated artificial aging influenced surface hardness of heat-polymerized acrylic resin Vipi Cril.

A comparison of the accuracy of patterns processed from an inlay casting wax, an auto-polymerized resin and a light-cured resin pattern material.

Science.gov (United States)

Rajagopal, Praveen; Chitre, Vidya; Aras, Meena A

2012-01-01

Traditionally, inlay casting waxes have been used to fabricate patterns for castings. Newer resin pattern materials offer greater rigidity and strength, allowing easier laboratory and intraoral adjustment without the fear of pattern damage. They also claim to possess a greater dimensional stability when compared to inlay wax. This study attempted to determine and compare the marginal accuracy of patterns fabricated from an inlay casting wax, an autopolymerized pattern resin and a light polymerized pattern resin on storage off the die for varying time intervals. Ten patterns each were fabricated from an inlay casting wax (GC Corp., Tokyo, Japan), an autopolymerized resin pattern material (Pattern resin, GC Corp, Tokyo, Japan) and a light-cured resin pattern material (Palavit GLC, Hereaus Kulzer GmbH, Germany). The completed patterns were stored off the die at room temperature. Marginal gaps were evaluated by reseating the patterns on their respective dies and observing it under a stereomicroscope at 1, 12, and 24 h intervals after pattern fabrication. The results revealed that the inlay wax showed a significantly greater marginal discrepancy at the 12 and 24 h intervals. The autopolymerized resin showed an initial (at 1 h) marginal discrepancy slightly greater than inlay wax, but showed a significantly less marginal gap (as compared to inlay wax) at the other two time intervals. The light-cured resin proved to be significantly more dimensionally stable, and showed minimal change during the storage period. The resin pattern materials studied, undergo a significantly less dimensional change than the inlay waxes on prolonged storage. They would possibly be a better alternative to inlay wax in situations requiring high precision or when delayed investment (more than 1 h) of patterns can be expected.

21 CFR 872.3750 - Bracket adhesive resin and tooth conditioner.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Bracket adhesive resin and tooth conditioner. 872... SERVICES (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3750 Bracket adhesive resin and tooth conditioner. (a) Identification. A bracket adhesive resin and tooth conditioner is a device...

Synthesis and characterization of an N-(2-hydroxyethyl)-ethylenediaminetriacetic acid resin

International Nuclear Information System (INIS)

Lai, Y.F.

1977-10-01

A chelating ion-exchange resin with N-(2-hydroxyethyl)ethylene-diaminetriacetic acid (HEDTA) used as the ligand chemically bonded to XAD-4 by an ester linkage, HEDTA-4, was synthesized. It is stable under normal experimental conditions with the liquid chromatograph. The structure of the resin was confirmed by an infrared spectrum, and by potentiometric titrations. The capacity of the resin was also obtained by potentiometric titration and by a nitrogen analysis. The resin was used to pack a column of 5 mm internal diameter and 5 cm long. The effect of pH on the retention of different metal ions on the resin was studied. It was found that the resin was most selective for chromium(III), copper(II), lead(II), mercury(II), uranium(VI), zirconium(IV) and zinc(II) at a pH of less than 3. Furthermore, the resin proves to be functioning with a chelating mechanism rather than ion-exchange, and it can concentrate trace metal ions in the presence of a large excess of calcium and magnesium. This makes the resin potentially useful for purifying and analyzing drinking water

Zinc incorporation improves biological activity of beta-tricalcium silicate resin-based cement.

Science.gov (United States)

Osorio, Raquel; Yamauti, Monica; Sauro, Salvatore; Watson, Tim F; Toledano, Manuel

2014-11-01

Matrix metalloproteinase (MMP) inhibition may improve endodontic treatment prognosis. The purpose of this study was to determine if zinc incorporation into experimental resin cements containing bioactive fillers may modulate MMP-mediated collagen degradation of dentin. Human dentin samples untreated and demineralized using 10% phosphoric acid or 0.5 mol/L EDTA were infiltrated with the following experimental resins: (1) unfilled resin, (2) resin with Bioglass 45S5 particles (OSspray, London, UK), (3) resin with beta-tricalcium silicate particles (βTCS), (4) resin with zinc-doped Bioglass 45S5, and (5) resin with zinc-doped βTCS particles. The specimens were stored in artificial saliva (for 24 hours, 1 week, and 4 weeks) and submitted to radioimmunoassay to quantify C-terminal telopeptide. Scanning electron microscopy analysis was also undertaken on dentin samples after 4 weeks of storage. Collagen degradation was prominent both in phosphoric acid and EDTA-treated dentin. Resin infiltration strongly reduced MMP activity in demineralized dentin. Resin containing Bioglass 45S5 particles exerted higher and stable protection of collagen. The presence of zinc in βTCS particles increases MMP inhibition. Different mineral precipitation was attained in dentin infiltrated with the resin cements containing bioactive fillers. MMP degradation of dentin collagen is strongly reduced after resin infiltration of dentin. Zinc incorporation in βTCS particles exerted an additional protection against MMP-mediated collagen degradation. However, it did not occur in resin containing Bioglass 45S5 particles, probably because of the formation of phosphate-zinc compounds. Copyright © 2014 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

New acrylic resin composite with improved thermal diffusivity.

Science.gov (United States)

Messersmith, P B; Obrez, A; Lindberg, S

1998-03-01

Studies have shown that physical characteristics of denture base materials may affect patient acceptance of denture prostheses by altering sensory experience of food during mastication. Thermal diffusivity is one material property that has been cited as being important in determining gustatory response, with denture base acrylic resins having low thermal diffusivity compared with denture base metal alloys. This study prepared and characterized experimental acrylic resin composite material with increased thermal diffusivity. Sapphire (Al2O3) whiskers were added to conventional denture base acrylic resin during processing to achieve loadings of 9.35% and 15% by volume. Cylindrical test specimens containing an embedded thermocouple were used to determine thermal diffusivity over a physiologic temperature range (0 degree to 70 degrees C). Thermal diffusivities of the sapphire containing composites were found to be significantly higher than the unmodified acrylic resin. Thermal diffusivity was found to increase in proportion to the volume percentage of sapphire filler, which suggested that the high aspect ratio ceramic particles formed a pathway for heat conduction through the insulating polymer matrix. The thermal diffusivity of denture base acrylic resin was increased by the addition of thermally conducting sapphire whiskers.

Computerized mathematical model for prediction of resin/fiber composite properties

International Nuclear Information System (INIS)

Lowe, K.A.

1985-01-01

A mathematical model has been developed for the design and optimization of resin formulations. The behavior of a fiber-reinforced cured resin matrix can be predicted from constituent properties of the formulation and fiber when component interaction is taken into account. A computer implementation of the mathematical model has been coded to simulate resin/fiber response and generate expected values for any definable properties of the composite. The algorithm is based on multistage regression techniques and the manipulation of n-order matrices. Excellent correlation between actual test values and predicted values has been observed for physical, mechanical, and qualitative properties of resin/fiber composites. Both experimental and commercial resin systems with various fiber reinforcements have been successfully characterized by the model. 6 references, 3 figures, 2 tables

Evaluation of resins for use in brachytherapy

Energy Technology Data Exchange (ETDEWEB)

Carvalho, Luiz Claudio F.M. Garcia; Ferraz, Wilmar Barbosa; Chrcanovic, Bruno Ramos; Santos, Ana Maria M., E-mail: ferrazw@cdtn.b, E-mail: amms@cdtn.b [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

2011-07-01

Brachytherapy is an advanced cancer treatment where radioactive seeds or sources are placed near or directly into the tumor thus reducing the radiation exposure in the surrounding healthy tissues. Prostate cancer can be treated with interstitial brachytherapy in initial stage of the disease in which tiny radioactive seeds with cylindrical geometry are used. Several kinds of seeds have been developed in order to obtain a better dose distribution around them and with a lower cost manufacturing. These seeds consist of an encapsulation, a radionuclide carrier, and X-ray marker. Among the materials that have potential for innovation in the construction of seeds, biocompatible resins appear as an important option. In this paper, we present some characterization results with Fourier transform infrared spectroscopic (FTIR) and ultraviolet-visible spectroscopy (UV-vis) performed on two types of resins in which curing temperatures for each one were varied as also the results of coatings with these resins under titanium substrates. Interactions of these resins in contact with the simulated body fluid were evaluated by atomic force microscopy, scanning electron microscopy, and energy dispersive X-ray spectroscopy. (author)

EB curable wetting resins for magnetic media coatings

International Nuclear Information System (INIS)

Laskin, L.; Ansel, R.E.; Murray, K.P.; Schmid, S.R.

1984-01-01

The magnetic media industry is studying means to improve the recording density, durability, product uniformity and production efficiency and to reduce wetting agent migration in the magnetic film. The use of electron beam curable resin binders for magnetic coatings is one of the approaches being studied for this. This paper compares the wetting efficiencies of several electron beam curable systems with a conventional resin and a conventional wetting agent. In this study it has been demonstrated that EB resins can be designed to effect proper magnetic pigment dispersion

Adsorption behaviour of uranium on immobilized tannin resin

International Nuclear Information System (INIS)

Olivares, Susana; Preval, Ivon; Santana, Jorge L.; Martinez, Francisco; Vargas, Luis M.

1995-01-01

The sorption of uranium by Eucalyptus Saligna Sm. tannin resin was investigated. This resin resulted a suitable adsorbent for the concentration of uranium from aqueous systems. The sorption of uranium is pH dependent. The presence of appreciable quantities of sodium chloride does not have any effect on uranium removal. Carbonate and calcium ions in concentrations similar to these found in seawater and other natural water do not decrease the uranium uptake. TANNsorb resin can be used several times without an appreciable decay of their sorption capacity. (author). 8 refs., 4 figs., 1 tab

Advanced ion exchange resins for PWR condensate polishing

International Nuclear Information System (INIS)

Hoffman, B.; Tsuzuki, S.

2002-01-01

The severe chemical and mechanical requirements of a pressurized water reactor (PWR) condensate polishing plant (CPP) present a major challenge to the design of ion exchange resins. This paper describes the development and initial operating experience of improved cation and anion exchange resins that were specifically designed to meet PWR CPP needs. Although this paper focuses specifically on the ion exchange resins and their role in plant performance, it is also recognized and acknowledged that excellent mechanical design and operation of the CPP system are equally essential to obtaining good results. (authors)

Effect of photocuring lamp type in the polymerization of various resins

International Nuclear Information System (INIS)

Lafuente, David; Blanco, Rosa; Brenes, Andrea

2005-01-01

Four different curing lamps were evaluated, a halogen and three LED technology with that are photocured five different resins. These four lamps have evaluated the surface hardness of the resin samples as a way of measuring the degree of polymerization. Comparing the Knoop surface hardness of the resin samples was found that the halogen light produced a greater surface hardness in all evaluated resins. (author) [es

Compatibility between dental adhesive systems and dual-polymerizing composite resins.

Science.gov (United States)

Michaud, Pierre-Luc; MacKenzie, Alexandra

2016-10-01

Information is lacking about incompatibilities between certain types of adhesive systems and dual-polymerizing composite resins, and universal adhesives have yet to be tested with these resins. The purpose of this in vitro study was to investigate the bonding outcome of dual-polymerizing foundation composite resins by using different categories of adhesive solutions and to determine whether incompatibilities were present. One hundred and eighty caries-free, extracted third molar teeth were allocated to 9 groups (n=20), in which 3 different bonding agents (Single Bond Plus [SB]), Scotchbond Multi-purpose [MP], and Scotchbond Universal [SU]) were used to bond 3 different composite resins (CompCore AF [CC], Core Paste XP [CP], and Filtek Supreme Ultra [FS]). After restorations had been fabricated using an Ultradent device, the specimens were stored in water at 37°C for 24 hours. The specimens were tested under shear force at a rate of 0.5 mm/min. The data were analyzed with Kruskal-Wallis tests and post hoc pairwise comparisons (α=.05). All 3 composite resins produced comparable shear bond strengths when used with MP (P=.076). However, when either SB or SU was used, the light-polymerized composite resin (FS) and 1 dual-polymerized foundation composite resin (CC) bonded significantly better than the other dual-polymerized foundation composite resin (CP) (Pincompatibilities exist between different products. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Study of mechanical and physicochemical properties of cementated spent ion-exchange-resins

International Nuclear Information System (INIS)

Patek, P.

1981-09-01

As first part of a study on the possibilities, to immobilize spent ion exchange resins, for final disposal, the dependence of compressive strength from the composition of cement - resin mixtures was detected. Powdered resins, bead resins and ashes from the incinerator plant and several cement brands were examinated. As result an area was defined in the three-phase diagram of cement, resins and water, in which the following leach tests will be performed. (author)

Composite resin fillings and inlays: An 11-year evaluation

DEFF Research Database (Denmark)

Pallesen, U.; Qvist, V.

2003-01-01

Clinical trial, composite resin, direct restorations, indirect restorations, long-term behaviour, posterior teeth......Clinical trial, composite resin, direct restorations, indirect restorations, long-term behaviour, posterior teeth...

76 FR 8774 - Granular Polytetrafluoroethylene Resin From Japan

Science.gov (United States)

2011-02-15

... INTERNATIONAL TRADE COMMISSION [Investigation No. 731-TA-386 (Third Review)] Granular Polytetrafluoroethylene Resin From Japan AGENCY: United States International Trade Commission. ACTION: Termination of five... revocation of the antidumping duty order on granular polytetrafluoroethylene resin from Japan would be likely...

21 CFR 173.25 - Ion-exchange resins.

Science.gov (United States)

2010-04-01

..., distilled water and 10 percent ethanol, when, following washing and pretreatment of the resin in accordance... paragraph (a)(18) of this section is used to treat aqueous sugar solutions subject to the condition that the temperature of the sugar solution passing through the resin bed is maintained at 82 °C (179.6 °F) or less and...

21 CFR 177.1900 - Urea-formaldehyde resins in molded articles.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Urea-formaldehyde resins in molded articles. 177... for Use as Basic Components of Single and Repeated Use Food Contact Surfaces § 177.1900 Urea-formaldehyde resins in molded articles. Urea-formaldehyde resins may be safely used as the food-contact surface...

Preoperative DTI and probabilistic tractography in an amputee with deep brain stimulation for lower limb stump pain.

Science.gov (United States)

Owen, S L F; Heath, J; Kringelbach, M L; Stein, J F; Aziz, T Z

2007-10-01

This study aimed to find out whether preoperative diffusion tensor imaging (DTI) and probabilistic tractography could help with surgical planning for deep brain stimulation in the periaqueductal/periventricular grey area (PAG/PVG) in a patient with lower leg stump pain. A preoperative DTI was obtained from the patient, who then received DBS surgery in the PAG/PVG area with good pain relief. The postoperative MRI scan showing electrode placement was used to calculate four seed areas to represent the contacts on the Medtronic 3387 electrode. Probabilistic tractography was then performed from the pre-operative DTI image. Tracts were seen to connect to many areas within the pain network from the four different contacts. These initial findings suggest that preoperative DTI scanning and probabilistic tractography may be able to assist surgical planning in the future.

Embedding in thermosetting resins

International Nuclear Information System (INIS)

Buzonniere, A. de

1985-01-01

Medium activity waste coming either from nuclear power plants in operation such as evaporator concentrates, spent resins, filter cartridges or the dismantling of installations are embedded in order to obtain a product suitable for long term disposal. Embedding in thermosetting resins (polyester or epoxy) is one among currently used techniques; it is being developed by the CEA (Commissariat a l'Energie Atomique) and Technicatome (subsidiary of CEA and EDF). The process is easy to operate and yields excellent results particularly as far as volume reduction and radioelement containment (cesium particularly) are concerned. The process has already been in operation in four stationary plants for several years. Extension of the process to mobile units has been completed by Technicatome in collaboration with the CEA [fr

Fracture Resistance of Endodontically Treated Teeth Restored with Biodentine, Resin Modified GIC and Hybrid Composite Resin as a Core Material.

Science.gov (United States)

Subash, Dayalan; Shoba, Krishnamma; Aman, Shibu; Bharkavi, Srinivasan Kumar Indu; Nimmi, Vijayan; Abhilash, Radhakrishnan

2017-09-01

The restoration of a severely damaged tooth usually needs a post and core as a part of treatment procedure to provide a corono - radicular stabilization. Biodentine is a class of dental material which possess high mechanical properties with excellent biocompatibility and bioactive behaviour. The sealing ability coupled with optimum physical properties could make Biodentine an excellent option as a core material. The aim of the study was to determine the fracture resistance of Biodentine as a core material in comparison with resin modified glass ionomer and composite resin. Freshly extracted 30 human permanent maxillary central incisors were selected. After endodontic treatment followed by post space preparation and luting of Glass fibre post (Reforpost, Angelus), the samples were divided in to three groups based on the type of core material. The core build-up used in Group I was Biodentine (Septodont, France), Group II was Resin-Modified Glass Ionomer Cement (GC, Japan) and Group III was Hybrid Composite Resin (TeEconom plus, Ivoclar vivadent). The specimens were subjected to fracture toughness using Universal testing machine (1474, Zwick/Roell, Germany) and results were compared using One-way analysis of variance with Tukey's Post hoc test. The results showed that there was significant difference between groups in terms of fracture load. Also, composite resin exhibited highest mean fracture load (1039.9 N), whereas teeth restored with Biodentine demonstrated the lowest mean fracture load (176.66 N). Resin modified glass ionomer exhibited intermediate fracture load (612.07 N). The primary mode of failure in Group I and Group II was favourable (100%) while unfavourable fracture was seen in Group III (30%). Biodentine, does not satisfy the requirements to be used as an ideal core material. The uses of RMGIC's as a core build-up material should be limited to non-stress bearing areas. Composite resin is still the best core build-up material owing to its high fracture

Method for loading resin beds

International Nuclear Information System (INIS)

Notz, K.J.; Rainey, R.H.; Greene, C.W.; Shockley, W.E.

1978-01-01

An improved method of preparing nuclear reactor fuel by carbonizing a uranium loaded cation exchange resin provided by contacting a H+ loaded resin with a uranyl nitrate solution deficient in nitrate, comprises providing the nitrate deficient solution by a method comprising the steps of reacting in a reaction zone maintained between about 145 to 200 0 C, a first aqueous component comprising a uranyl nitrate solution having a boiling point of at least 145 0 C with a second aqueous component to provide a gaseous phase containing HNO 3 and a reaction product comprising an aqueous uranyl nitrate solution deficient in nitrate

Nanomechanical properties of dental resin-composites.

Science.gov (United States)

El-Safty, S; Akhtar, R; Silikas, N; Watts, D C

2012-12-01

To determine by nanoindentation the hardness and elastic modulus of resin-composites, including a series with systematically varied filler loading, plus other representative materials that fall into the categories of flowable, bulk-fill and conventional nano-hybrid types. Ten dental resin-composites: three flowable, three bulk-fill and four conventional were investigated using nanoindentation. Disc specimens (15mm×2mm) were prepared from each material using a metallic mold. Specimens were irradiated in the mold at top and bottom surfaces in multiple overlapping points (40s each) with light curing unit at 650mW/cm(2). Specimens were then mounted in 3cm diameter phenolic ring forms and embedded in a self-curing polystyrene resin. After grinding and polishing, specimens were stored in distilled water at 37°C for 7 days. Specimens were investigated using an Agilent Technologies XP nanoindenter equipped with a Berkovich diamond tip (100nm radius). Each specimen was loaded at one loading rate and three different unloading rates (at room temperature) with thirty indentations, per unloading rate. The maximum load applied by the nanoindenter to examine the specimens was 10mN. Dependent on the type of the resin-composite material, the mean values ranged from 0.73GPa to 1.60GPa for nanohardness and from 14.44GPa to 24.07GPa for elastic modulus. There was a significant positive non-linear correlation between elastic modulus and nanohardness (r(2)=0.88). Nonlinear regression revealed a significant positive correlation (r(2)=0.62) between elastic moduli and filler loading and a non-significant correlation (r(2)=0.50) between nanohardness and filler loading of the studied materials. Varying the unloading rates showed no consistent effect on the elastic modulus and nanohardness of the studied materials. For a specific resin matrix, both elastic moduli and nanohardness correlated positively with filler loading. For the resin-composites investigated, the group-average elastic

Behavior study of spend ion exchange resins immobilized in pyrolyzed polymer matrix

International Nuclear Information System (INIS)

Ramos, P.B; Fuentes, N.O; Luca, V.

2012-01-01

The pyrolysis of spent ion exchange resins contained in epoxy resins represents an attractive alternative to cementation as a confining method. In this sense, a significant reduction of volume can be achieved, as well as avoiding the dispersion of the exhausted ion exchange resin by the means of an epoxy resin used as a matrix, while potentially limiting the release of highly radioactive long life isotopes such us Cs-137, Sr-90 and Co-60 among others. Three types of monoliths were made: (i) epoxy resin, (ii) epoxy resin with carbon and (iii) a binder of epoxy resin and clay. In every case, the monolith contained the ion exchange resin. They were prepared by the mixing of resin pearl loaded with epoxy cations and a subsequent pyrolysis process with a temperature increase ratio of 2 o C /min reaching maximum values in the range between 200 o C - 800 o C, remaining in it for 1 hour. Monoliths obtained for each final temperature had been characterized to obtain data corresponding to the mass loss, volume reduction and lixiviation, as well as mechanical and microstructural properties (author)

Removal of Uranium by Exchanger Resins from Soil Washing Solution

Energy Technology Data Exchange (ETDEWEB)

Kim, Seung Soo; Han, G. S.; Kim, G. N.; Koo, D. S.; Jeong, J. W.; Moon, J. K. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2015-05-15

Uranyl ions in the acidic waste solution were sorbed on AM-resin resin with a high sorption efficiency, and desorbed from the resin by a batch-type washing with a 60 .deg. C heated 0.5 M Na{sub 2}CO{sub 3} solution. However, the uranium dissolved in the sulfuric acid solution was not sorbed onto the strong anion exchanger resins. Our group has developed a decontamination process with washing and electrokinetic methods for uranium-contaminated (U-contaminated) soil. However, this process generates a large amount of waste solution containing various metal ions. If the uranium selectively removed from the waste solution, a very small amount of the 2nd waste would be generated. Thus, selective sorption of uranium by ion exchange resins was examined in this study.

Attribute based selection of thermoplastic resin for vacuum infusion process

DEFF Research Database (Denmark)

Prabhakaran, R.T. Durai; Lystrup, Aage; Løgstrup Andersen, Tom

2011-01-01

The composite industry looks toward a new material system (resins) based on thermoplastic polymers for the vacuum infusion process, similar to the infusion process using thermosetting polymers. A large number of thermoplastics are available in the market with a variety of properties suitable...... for different engineering applications, and few of those are available in a not yet polymerised form suitable for resin infusion. The proper selection of a new resin system among these thermoplastic polymers is a concern for manufactures in the current scenario and a special mathematical tool would...... be beneficial. In this paper, the authors introduce a new decision making tool for resin selection based on significant attributes. This article provides a broad overview of suitable thermoplastic material systems for vacuum infusion process available in today’s market. An illustrative example—resin selection...

Microwave Assisted Regioselective Bromomethoxylation of Alkenes Using Polymer Supported Bromine Resins

OpenAIRE

Gopalakrishnan, Geetha; Kasinath, Viswanathan; Singh, N. D. Pradeep; Krishnan, V. P. Santhana; Solomon, K. Anand; Rajan, S. S.

2002-01-01

A facile regio- and chemoselective bromomethoxylation of alkenes under microwave irradiation conditions employing a new polymer supported brominechloride resin is reported. The resin is prepared from the commercially available chloride resin by a simple one step procedure.

In situ ∼2.0 Ma trees discovered as fossil rooted stumps, lowermost Bed I, Olduvai Gorge, Tanzania.

Science.gov (United States)

Habermann, Jörg M; Stanistreet, Ian G; Stollhofen, Harald; Albert, Rosa M; Bamford, Marion K; Pante, Michael C; Njau, Jackson K; Masao, Fidelis T

2016-01-01

The discovery of fossil rooted tree stumps in lowermost Lower Bed I from the western Olduvai Basin, Tanzania, age-bracketed by the Naabi Ignimbrite (2.038 ± 0.005 Ma) and Tuff IA (1.88 ± 0.05 Ma), provides the first direct, in situ, and to date oldest evidence of living trees at Olduvai Gorge. The tree relicts occur in an interval dominated by low-viscosity mass flow and braided fluvial sediments, deposited at the toe of a largely Ngorongoro Volcano-sourced volcaniclastic fan apron that comprised a widely spaced network of ephemeral braided streams draining northward into the Olduvai Basin. Preservation of the trees occurred through their engulfment by mass flows, post-mortem mold formation resulting from differential decay of woody tissues, and subsequent fluvially-related sediment infill, calcite precipitation, and cast formation. Rhizolith preservation was triggered by the interaction of root-induced organic and inorganic processes to form rhizocretionary calcareous root casts. Phytolith analyses were carried out to complete the paleoenvironmental reconstruction. They imply a pronounced seasonality and indicate a wooded landscape with grasses, shrubs, and sedges growing nearby, comparable to the low, open riverine woodland (unit 4c) along the Garusi River and tributaries in the Laetoli area. Among the tree stump cluster were found outsized lithic clasts and those consisting of quartzite were identified as Oldowan stone tool artifacts. In the context of hominin activity, the identification of wooded grassland in association with nearby freshwater drainages and Oldowan artifacts significantly extends our paleoenvironmental purview on the basal parts of Lower Bed I, and highlights the hitherto underrated role of the yet poorly explored western Olduvai Gorge area as a potential ecologically attractive setting and habitat for early hominins. Copyright © 2015 Elsevier Ltd. All rights reserved.

Biocompatibility of acrylic resin after being soaked in sodium hypochlorite

Directory of Open Access Journals (Sweden)

Nike Hendrijatini

2009-06-01

Full Text Available Background: Acrylic resin as basic material for denture will stay on oral mucosa for a very long time. The polymerization of acrylic resin can be performed by conventional method and microwave, both produce different residual monomer at different toxicity. Acrylic resin can absorb solution, porous and possibly absorb disinfectantt as well, that may have toxic reaction with the tissue. Sodium Hypochlorite as removable denture disinfectant can be expected to be biocompatible to human body. The problem is how biocompatible acrylic resin which has been processed by conventional method and microwave method after being soaked in sodium hypochlorite solution. Purpose: The aim of this study was to understand in vitro biocompatibility of acrylic resin which has polimerated by conventional method and microwave after being soaked in sodium hypochlorite using tissue culture. Methods: Four groups of acrylic resin plate were produced, the first group was acrylic resin plate with microwave polymeration and soaked in sodium hypochlorite, the second group was acrylic resin plate with microwave polymeration but not soaked, the thirdwas one with conventional method and soaked and the last group was one with conventional method but not soaked, and in 1 control group. Each group consists of 7 plates. Biocompatibility test was performed in-vitro on each material using fibroblast tissue culture (BHK-21 cell-line. Result: The percentage between living cells and dead cells from materials which was given acrylic plate was wounted. The data was analyzed statistically with T test. Conclusion: The average value of living cells is higher in acrylic resin poimerization using microwave method compared to conventional method, in both soaked and non soaked (by sodium hypochlorite group. This means that sodium hypochlorite 0.5% was biocompatible to the mouth mucosa as removable denture disinfectant for 10 minutes soaking and washing afterwards.

Synthesis and Mechanism of Metal-Mediated Polymerization of Phenolic Resins

Directory of Open Access Journals (Sweden)

Zhao Yi

2016-04-01

Full Text Available Phenol-formaldehyde (PF resin is a high performance adhesive, but has not been widely developed due to its slow curing rate and high curing temperature. To accelerate the curing rate and to lower the curing temperature of PF resin, four types of metal-mediated catalysts were employed in the synthesis of PF resin; namely, barium hydroxide (Ba(OH2, sodium carbonate (Na2CO3, lithium hydroxide (LiOH, and zinc acetate ((CH3COO2Zn. The cure-acceleration effects of these catalysts on the properties of PF resins were measured, and the chemical structures of the PF resins accelerated with the catalysts were investigated by using Fourier transform infrared (FT-IR spectroscopy and quantitative liquid carbon-13 nuclear magnetic resonance (13C NMR. The results showed that the accelerated efficiency of these catalysts to PF resin could be ordered in the following sequence: Na2CO3 > (CH3COO2Zn > Ba(OH2 > LiOH. The catalysts (CH3COO2Zn and Na2CO3 increased the reaction activity of the phenol ortho position and the condensation reaction of ortho methylol. The accelerating mechanism of (CH3COO2Zn on PF resin is probably different from that of Na2CO3, which can be confirmed by the differences in the differential thermogravimetric (DTG curve and thermogravimetric (TG data. Compared to the Na2CO3-accelerated PF resin, the (CH3COO2Zn-accelerated PF resin showed different peaks in the DTG curve and higher weight residues. In the synthesis process, the catalyst (CH3COO2Zn may form chelating compounds (containing a metal-ligand bond, which can promote the linkage of formaldehyde to the phenolic hydroxyl ortho position.

Method of pyrolysis for spent ion-exchange resins

International Nuclear Information System (INIS)

Aoyama, Yoshiyuki; Matsuda, Masami; Kawamura, Fumio; Yusa, Hideo.

1985-01-01

Purpose: To prevent the generation of noxious sulfur oxide and ammonia on the pyrolysis for spent ion-exchange resins discharged from nuclear power plants. Method: In the case where the pyrolysis is made for the cationic exchange resins having sulfonic acids as the ion-exchange group, alkali metals or alkaline earth metals capable of reacting with sulfonic acid groups to form solid sulfates are previously deposited by way of ion-exchange reactions prior to the pyrolysis. In another case of the anionic exchange resins having quarternary ammonium groups as the ion-exchange groups, halogenic elements capable of reacting with the ammonium groups to form solid ammonium salts are deposited to the ion-exchange resins through ion-exchange reactions prior to the pyrolysis. As a result, the amount of the binders used can be reduced, and this method can be used in a relatively simple processing facility. (Horiuchi, T.)

ON THE DURABILITY OF RESIN-DENTIN BONDS: IDENTIFYING THE WEAKEST LINKS

Science.gov (United States)

Zhang, Zihou; Beitzel, Dylan; Mutluay, Mustafa; Tay, Franklin R.; Pashley, David H.; Arola, Dwayne

2015-01-01

Fatigue of resin-dentin adhesive bonds is critical to the longevity of resin composite restorations. Objectives The objectives were to characterize the fatigue and fatigue crack growth resistance of resin-dentin bonds achieved using two different commercial adhesives and to identify apparent “weak-links”. Methods Bonded interface specimens were prepared using Adper Single Bond Plus (SB) or Adper Scotchbond Multi-Purpose (SBMP) adhesives and 3M Z100 resin composite according to the manufacturers instructions. The stress-life fatigue behavior was evaluated using the twin bonded interface approach and the fatigue crack growth resistance was examined using bonded interface Compact Tension (CT) specimens. Fatigue properties of the interfaces were compared to those of the resin-adhesive, resin composite and coronal dentin. Results The fatigue strength of the SBMP interface was significantly greater than that achieved by SB (p≤0.01). Both bonded interfaces exhibited significantly lower fatigue strength than that of the Z100 and dentin. Regarding the fatigue crack growth resistance, the stress intensity threshold (ΔKth) of the SB interface was significantly greater (p≤0.01) than that of the SBMP, whereas the ΔKth of the interfaces was more than twice that of the parent adhesives. Significance Collagen fibril reinforcement of the resin adhesive is essential to the fatigue crack growth resistance of resin-dentin bonds. Resin tags that are not well hybridized into the surrounding intertubular dentin and/or poor collagen integrity are detrimental to the bonded interface durability. PMID:26169318

Ion exchange resin fouling of molybdenum in recovery uranium processess

International Nuclear Information System (INIS)

Zhang Guowei; Zhao Guirong

1990-09-01

The relationship between anion exchange resin fouling and molybdic acid polymerization was studied. By using potentiometer titration and laser-Raman spectroscopy the relationship of molybdic acid polymerization and the pH value of solution or the molybdenum concentration was determined. It was shown that as the concentration of initial molybdenum in solution decreases from 0.2 mol/L to 0.5 mmol/L, the pH value of starting polymerization decreased from 6.5 to 4.5. The experimental results show that the fouling of 201 x 7 resin in the acidic solution is mainly caused by the adsorbing of Mo 3 O 26 4- ion and occupying the exchange radical site of the resin. Under the leaching conditions the molybdenum and phosphate existing in the leaching liquor can form 12-molybdo-phosphate ion. It also leads to resin fouling. The molybdenum on the fouled resin can synergically be desorbed by mixed desorbents containing ammonium hydroxide and ammonium sulfate. The desorbed resin can be used for uranium adsorption and the desorbed molybdenum can be recovered by ion exchange method

Handling sticky Resin by Stingless Bees: Adhesive Properties of Surface Structures

Directory of Open Access Journals (Sweden)

MARKUS GASTAUER

2013-09-01

Full Text Available Many Stingless Bees (Hymenoptera: Meliponini like Tetragonisca angustula collect resin to defend their nests against intruders like ants or Robber Bees. Small portions of resin are attached to intruders bodies and extremities causing their immobilization. It has been observed that resin is removed easily from the bee's mandible but adheres strongly to the intruder's cuticle. We tested the hypothesis that resin sticks lesser to the mandibles of Stingless Bees than to the surface of intruders due to special surface structures or adhesive properties of these structures. The surface structures of the mandible of T. angustula and the trochanter of Camponotus sericeiventris were studied by scanning electron microscopy. To measure adhesion properties, selected surfaces were fixed on a fine glass pin and withdrawn from a glass tip covered with resin. The deformation of the glass pin indicates adhesion forces operating between the resin and the selective surface. The absolute value of the forces is computed from the glass pin's stiffness. It has been shown that resin sticks more to the smooth mandible of the bee than to the structured trochanter of the ant. A new hypothesis to be tested says that the bees might lubricate their mandibles with nectar or honey to reduce the resin's adhesion temporarily.

Wet oxidative destruction of spent ion-exchange resins using hydrogen peroxide

International Nuclear Information System (INIS)

Srinivas, C.; Ramaswamy, M.; Theyyunni, T.K.

1994-01-01

Spent organic ion exchange resins are generated in large quantities during the operation of nuclear facilities. Wet oxidation as a mode of treatment of these gel-type ion exchange resins was investigated using H 2 O 2 as oxidant in the presence of CuSO 4 as catalyst. Experiments using commercial samples were conducted at 95-100 deg C under reflux conditions at atmospheric pressure. It was found that the reaction of cation resin with H 2 O 2 was instantaneous whereas with anion resin, there was a lag time. For efficient utilization of the oxidant, low rate of addition of H 2 O 2 , 0.01M concentration of CuSO 4 and neutral pH in mixed resin reactions, were found to be useful. Foaming was noted during reactions involving anion resins. This could be controlled by silicone-based agents. The residual solution left after resin oxidation is aqueous in nature and is expected to contain all the radioactivity originally present in the resin. Preliminary experiments showed that it could be efficiently trapped using available inorganic sorbents. Wet oxidation system offers a simple method of converting organic waste into environmentally acceptable inorganic products. (author). 8 refs., 6 figs., 2 tabs

Immobilization in cement of ion exchange resins from Spanish nuclear reactors

International Nuclear Information System (INIS)

Huebra, A.G. de la; Murillo, R.; Ortiz, S.J.

1990-01-01

Ion exchange materials used at nuclear power plants can be immobilized in cements less expensive than polymer matrices. Cement solidification of spent ion exchange resins shows swelling and cracking troubles (during setting time, or of storage). The objective of this study was to select the types of cement that produce the best quality on immobilization of three kinds of resins and to set up cement formulations containing the maximum possible loading of resin. Four cements were selected to carried out the study. After a study of hydration-dehydration phenomena of ion exchange resins, a systematic work has been carried out on immobilization. Tests were performed to study compressive strength and underwater stability by changing water/cement ratio and resin/cement ratio. Mixtures made with water, cement and resin only were loaded with 10% by weight dry resin. Mixtures with higher loadings show poor workability. Tests were carried out by adding organic plasticizers and silica products to improve waste loading. Plasticizers reduced water demand and silica products permit the use of more water. Leaching tests have been performed at 40 O C. In conclusion Blast Furnace Slag is the best cement for immobilization of ion exchange resin both bead and powdered form for mechanical strength, stability and leaching

Perchlorate adsorption and desorption on activated carbon and anion exchange resin.

Science.gov (United States)

Yoon, In-Ho; Meng, Xiaoguang; Wang, Chao; Kim, Kyoung-Woong; Bang, Sunbaek; Choe, Eunyoung; Lippincott, Lee

2009-05-15

The mechanisms of perchlorate adsorption on activated carbon (AC) and anion exchange resin (SR-7 resin) were investigated using Raman, FTIR, and zeta potential analyses. Batch adsorption and desorption results demonstrated that the adsorption of perchlorate by AC and SR-7 resin was reversible. The reversibility of perchlorate adsorption by the resin was also proved by column regeneration test. Solution pH significantly affected perchlorate adsorption and the zeta potential of AC, while it did not influence perchlorate adsorption and the zeta potential of resin. Zeta potential measurements showed that perchlorate was adsorbed on the negatively charged AC surface. Raman spectra indicated the adsorption resulted in an obvious position shift of the perchlorate peak, suggesting that perchlorate was associated with functional groups on AC at neutral pH through interactions stronger than electrostatic interaction. The adsorbed perchlorate on the resin exhibited a Raman peak at similar position as the aqueous perchlorate, indicating that perchlorate was adsorbed on the resin through electrostatic attraction between the anion and positively charged surface sites.

Campuran kitosan dengan resin akrilik sebagai bahan gigi tiruan penghambat Candida albicans

Directory of Open Access Journals (Sweden)

Titik Ismiyati

2018-04-01

Full Text Available The mixture of acrylic resin and chitosan as denture material to inhibit Candida albicans. The inhibition of Candida albicans in denture resin has an important role to prevent the development of denture stomatitis. Chitosan is a natural polymer compound derived from shrimp waste which can function as an antifungal Acrylik resin cannot be mixed with chitosan. To obtain a homogeneous mixture, the mixture was added a coupling agen acrylic acid and acetone. The research objective was to study the mixture of acrylic resin and chitosan with solvent acrylic acid and acetone as a denture that can inhibit the growth of Candida albicans. Methods: The samples used discs in 10 mm diameter and 2 mm thickness, made from heat cured acrylic resin mixed with chitosan dissolved in acrylat acid and acetone. They were divided into 4 groups. Group 1 was acrylic resin without chitosan as a control, group 2, 3 and 4 were the mixture of acrylic resin and 5 ml chitosan in 0.5%, 1%, and 2% concentration respectively. The fourier transform irfrared spectroscopy (FTIR and the digital optical microscope were used to synthesize and analyze. The Kruskal Wallis was used to analyze the data. The results showed that the mixture of acrylic resin with chitosan significantly inhibited the growth of Candida albicans. Conclusion: a mixture of acrylic resins and chitosan can be fungistatic, so it can be developed as an antifungal denture material.   ABSTRAK Penghambatan Candida albicans pada gigi tiruan resin akrilik dapat memainkan peran penting dalam mencegah perkembangan denture stomatitis. Kitosan adalah senyawa polimer alam yang berasal dari limbah udang yang dapat berfungsi sebagai antijamur. Resin akrilik tidak dapat bercampur dengan kitosan. Untuk mendapatkan campuran yang homogen, campuran tersebut ditambah coupling agent asam akrilat dan aseton. Penelitian ini bertujuan untuk mengkaji campuran resin akrilik dan kitosan dan asam akrilat pelarut aseton sebagai bahan gigi

Treatment of Simulated Soil Decontamination Waste Solution by Ferrocyanide-Anion Exchange Resin Beads

Energy Technology Data Exchange (ETDEWEB)

Won, Hui Jun; Kim, Min Gil; Kim, Gye Nam; Jung, Chung Hun; Park, Jin Ho; Oh, Won Zin [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2005-03-15

Preparation of ferrocyanide-anion exchange resin and adsorption test of the prepared resin on the Cs{sup -} ion were performed. Adsorption capability of the prepared resin on the Cs{sup -} ion in the simulated citric acid based soil decontamination waste solution was 4 times greater than that of the commercial cation exchange resin. Adsorption equilibrium of the prepared resin on the Cs{sup -} ion reached within 360 minutes. Adsorption capability on the Cs{sup -} ion became to decrease above the necessary Co{sup 2-} ion concentration in the experimental range. Recycling test of the spent ion exchange resin by the successive application of hydrogen peroxide and hydrazine was also performed. It was found that desorption of Cs{sup -} ion from the resin occurred to satisfy the electroneutrality condition without any degradation of the resin.

A review of the development of resins for use in hydrometallurgy

International Nuclear Information System (INIS)

Green, B.R.

1985-01-01

Commercial resins, including cation exchangers, anion exchangers, and complexing resins, that may be suitable for use in the extraction of metals are reviewed. Areas where further research is required are considered, and potential applications that are of particular interest to the Council for Mineral Technology (Mintek), involving the recovery of uranium, gold, and the base metals, are described. Commercial resins and experimental resins developed at Mintek are evaluated, and the results are reviewed

EPICOR-II resin characterization and proposed methods for degradation analysis. Rev. 1

International Nuclear Information System (INIS)

Doyle, J.D.; McConnell, J.W. Jr.; Sanders, R.D. Sr.

1984-06-01

One goal of the EPICOR-II Research and Disposition Program is the examination of the EPICOR-II organic ion-exchange resins for physical and chemical degradation. This report summarizes preliminary information necessary for the evaluation of the resins for degradation. Degradation of the synthetic organic ion-exchange resins should be efficiently and accurately measurable by using the baseline data provided by the nonirradiated resin characterization. The degradation threshold is about 10 8 rads, approximately the same dose rate the resins will have received by the examination date. If degradation has not occurred at the first examination point, later examinations will detect resin degradation using the same analytical methods. The results from the characterization tests will yield practical and useful data on the actual effects of radiation on commercial synthetic organic ion-exchange resins. 10 references, 12 figures

Apparatus and method for removing solvent from carbon dioxide in resin recycling system

Science.gov (United States)

Bohnert, George W [Harrisonville, MO; Hand, Thomas E [Lee's Summit, MO; DeLaurentiis, Gary M [Jamestown, CA

2009-01-06

A two-step resin recycling system and method solvent that produces essentially contaminant-free synthetic resin material. The system and method includes one or more solvent wash vessels to expose resin particles to a solvent, the solvent contacting the resin particles in the one or more solvent wash vessels to substantially remove contaminants on the resin particles. A separator is provided to separate the solvent from the resin particles after removal from the one or more solvent wash vessels. The resin particles are next exposed to carbon dioxide in a closed loop carbon dioxide system. The closed loop system includes a carbon dioxide vessel where the carbon dioxide is exposed to the resin, substantially removing any residual solvent remaining on the resin particles after separation. A separation vessel is also provided to separate the solvent from the solvent laden carbon dioxide. Both the carbon dioxide and the solvent are reused after separation in the separation vessel.

Color change of composite resins subjected to accelerated artificial aging

Directory of Open Access Journals (Sweden)

Denise Cremonezzi Tornavoi

2013-01-01

Conclusions: All composite resins presented unacceptable color changes after 382 h of aging and different composite resins with same hue, presented different colors before being subjected to the aging process (B2 and C2 and after (B2. It was also observed color difference within a group of the same composite resin and same hue.

Surface discoloration of composite resins: Effects of staining and bleaching.

Science.gov (United States)

Poggio, Claudio; Beltrami, Riccardo; Scribante, Andrea; Colombo, Marco; Chiesa, Marco

2012-09-01

The purpose of this in vitro study was to evaluate surface discoloration of three microhybrid composite resins (Esthet•X HD, Clearfil AP-X, Gradia Direct) and five nanohybrid composite resins (Ceram•X, GC Kalore, G-aenial, Grandio, GrandioSO), after staining and bleaching procedures. The composite resins were polymerized with a curing light (Celalux II, Voco, Cuxhaven, Germany) into 160 silicon molds (6,4 mm in diameter and 2 mm in thickness) to obtain identical specimens. Twenty samples for each composite resin were prepared. The specimens were polished using an automated polishing machine with the sequence of 600-, 800-, 1000-grit abrasive paper under water irrigation. The specimens were immersed in tea and distilled water: the specimens were dipped for 20 min, once a day (every 24 h), for 14 days into the drinks. The specimens were then bleached with carbamide peroxide at 17% (Perfect Bleach-Voco). The color of specimens was measured with a spectrophotometer according to the CIE L(*)a(*)b(*) system after light-polymerization of composite resin specimens, after 7 days, after 14 days, and after bleaching. The color difference h index (DEab(*)) between each measurement was calculated. Statistical analysis was made using analysis of variance (ANOVA). All specimens showed a significant increase in staining with a similar trend and no significant differences between microhybrid and nanohybrid composite resins. After whitening procedures, materials tested showed both significant and unsignificant differences of the h index. Microhybrid and nanohybrid composite resins had similar in vitro surface discoloration in tea. After bleaching, discoloration was removed from some composite resins tested.

Kekerasan mikro resin komposit packable dan bulkfill dengan kedalaman kavitas berbeda

Directory of Open Access Journals (Sweden)

Diatri Nari Ratih

2017-12-01

Full Text Available Microhardness of packable and bulkfill composite resin with different cavity depths. Bulkfill composite resin restorations are increasingly popular because the material can be irradiated with a thickness reaching 4 mm, making it easier to apply. The objective of this study was to determine the differences in the microhardness between packable and bulkfill composite resin restorations with a cavity depth of 2 mm and 4 mm. This study was done using 32 Teon molds (5 mm diameter, and grouped randomly into 4 groups in which each consisted of 8 samples. Group 1A, packable composite resin was applied to the mold with a cavity depth of 2 mm. Group 1B, bulkfill composite resin was applied to the mold with a cavity depth of 2 mm. Group 2A, packable composite resin was applied with a depth of 4 mm. Group 2B, bulkfill composite resin was applied with a depth of 4 mm. Each sample was immersed in articial saliva with a pH of 6.8 and stored in an incubator at a temperature of 37°C for 24 hours. The hardness of each sample was tested using Vickers indenter microhardness tester. The data obtained were then analyzed by using two-way ANOVA, followed by Tukey’s test. The results showed that bulkfill composite resin with a cavity depth of 2 mm has the highest average of microhardness (31.09 ± 2.02 VHN, followed by packable composite resin with a depth of 2 mm (17.52 ± 1.25 VHN, bulkfill with a depth of 4 mm (11.97 ± 1.23 VHN and packable with a depth of 4 mm (3.18 ± 0.85 VHN. The two-way ANOVA analysis showed that there are significant differences between the types of composite resin and cavity depths (p < 0.05, and there is interaction between the types of composite resin and cavity depth (p<0.05. In conclusion, the microhardness of packable composite resin is lower than that of bulkfill at a cavity depth of 2 and 4 mm.   ABSTRAK Restorasi resin komposit dengan bulkfill semakin populer karena material tersebut dapat disinar dengan ketebalan sampai 4

Westinghouse Modular Grinding Process - Enhancement of Volume Reduction for Hot Resin Supercompaction - 13491

Energy Technology Data Exchange (ETDEWEB)

Fehrmann, Henning [Westinghouse Electric Germany GmbH, Dudenstr. 44, D-68167 Mannheim (Germany); Aign, Joerg [Westinghouse Electric Germany GmbH, Global D and D and Waste Management, Tarpenring 6, D-22419 Hamburg (Germany)

2013-07-01

In nuclear power plants (NPP) ion exchange (IX) resins are used in several systems for water treatment. Spent resins can contain a significant amount of contaminates which makes treatment for disposal of spent resins mandatory. Several treatment processes are available such as direct immobilization with technologies like cementation, bitumisation, polymer solidification or usage of a high integrity container (HIC). These technologies usually come with a significant increase in final waste volume. The Hot Resin Supercompaction (HRSC) is a thermal treatment process which reduces the resin waste volume significantly. For a mixture of powdered and bead resins the HRSC process has demonstrated a volume reduction of up to 75 % [1]. For bead resins only the HRSC process is challenging because the bead resins compaction properties are unfavorable. The bead resin material does not form a solid block after compaction and shows a high spring back effect. The volume reduction of bead resins is not as good as for the mixture described in [1]. The compaction properties of bead resin waste can be significantly improved by grinding the beads to powder. The grinding also eliminates the need for a powder additive.Westinghouse has developed a modular grinding process to grind the bead resin to powder. The developed process requires no circulation of resins and enables a selective adjustment of particle size and distribution to achieve optimal results in the HRSC or in any other following process. A special grinding tool setup is use to minimize maintenance and radiation exposure to personnel. (authors)

Microhardness of resin composite materials light-cured through fiber reinforced composite.

NARCIS (Netherlands)

Fennis, W.M.M.; Ray, N.J.; Creugers, N.H.J.; Kreulen, C.M.

2009-01-01

OBJECTIVES: To compare polymerization efficiency of resin composite basing materials when light-cured through resin composite and fiber reinforced composite (FRC) by testing microhardness. METHODS: Simulated indirect restorations were prepared by application of resin composite (Clearfil AP-X) or FRC

Microwave Assisted Regioselective Bromomethoxylation of Alkenes Using Polymer Supported Bromine Resins

Directory of Open Access Journals (Sweden)

S. S. Rajan

2002-05-01

Full Text Available A facile regio- and chemoselective bromomethoxylation of alkenes under microwave irradiation conditions employing a new polymer supported brominechloride resin is reported. The resin is prepared from the commercially available chloride resin by a simple one step procedure.

Development of new addition-type composite resins

Science.gov (United States)

Kray, R. J.

1981-01-01

The most promising of a number of new addition type polyimides and polyaromatic melamine (NCNS) resins for use in high performance composite materials. Three different cure temperature ranges were of interest: 530-560 K (500-550 F), 475-530 K (400-500 F), and 450 K (350 F). Examined were a wide variety of polyimide precursors terminated with 5 norbornene groups and addition polymerized at 560 K similar to PMR-15 and LARC-160 polyimides. In addition, a number of lower curing cinnamal end capped polyimides and a bismaleimide were investigated but were not found promising. A group of NCNS resins were investigated and some were found to be superior to current epoxy resins in moisture resistance, oxidative aging and flame and smoke properties.

Pilot Plant for treating of spent exchange resins

International Nuclear Information System (INIS)

Iglesias, Alberto M.; Raffo Calderon, Maria del C.; Varani, Jose L.

2004-01-01

Spent exchange resins that have been accumulating during the last operational 30 years in Atucha I nuclear power plant (NPP) are a 'problematic' waste. These spent resins conform an intermediate level waste due to the total content of alpha, beta and gamma emitters (some samples of spent resins were analyzed in 2003). For this reason its treatment is more expensive since it is necessary to add more safety barriers for its final disposition and also for the radioprotection actions that are involved. Using sulfuric acid solutions it is possible to elute from the spent resins the ions that are retained. In the same operation are eluted Cobalt, Cesium and alpha emitters since that all these elements react as cations in aqueous solution. Decontamination by electrochemical methods was analyzed as an interesting method to apply after elution operation to these spent resins since that with the decontamination process it is possible to obtain a solid without activity and concentrate the activity in cells that are small in volume and its manipulation doesn't present any extra complication. Experiments made with active samples taken from the deposit were successful. Because of these results it was built a small plant to treat a batch of 100 dm 3 of wet spent exchange resins. Some problems with the material that was in the deposit together with spent resins caused that we had to plan a more complex strategy to obtain a complete decontamination of the spent resins (in this stage we used the cobalt retention cell that was described in other paper to retain Cobalt and alpha emitters and a sample of zeolites from Argentina ores to retain Cesium). Due to alpha emitters act electrochemically like cations it was possible to retain altogether with ionic Cobalt on the copper amalgam electrode. Working in the non-active lab with alcoholic solutions it was possible to retain ionic Cesium on a copper electrode (copper is covered by mercury fine film which forms a solid amalgam) with a

The selection of adhesive systems for resin-based luting agents.

Science.gov (United States)

Carville, Rebecca; Quinn, Frank

2008-01-01

The use of resin-based luting agents is ever expanding with the development of adhesive dentistry. A multitude of different adhesive systems are used with resin-based luting agents, and new products are introduced to the market frequently. Traditional adhesives generally required a multiple step bonding procedure prior to cementing with active resin-based luting materials; however, combined agents offer a simple application procedure. Self-etching 'all-in-one' systems claim that there is no need for the use of a separate adhesive process. The following review addresses the advantages and disadvantages of the available adhesive systems used with resin-based luting agents.

The characteristics of epoxy resin cured by {gamma}-ray and E-beam

Energy Technology Data Exchange (ETDEWEB)

Nho, Y.C. E-mail: ycnho@kaeri.re.kr; Kang, Phil Hyun; Park, Jong Seok

2004-10-01

Epoxy resins are widely used as high-performance thermosetting resins for many industrial applications. In this study, the effect of an electron beam (E-beam) and {gamma}-ray irradiation on the curing of epoxy resins was investigated. Diglycidyl ether of bisphenol-A(DGEBA), diglycidyl ether of bisphenol-F(DGEBF) as epoxy resins, triarylsulfonium hexafluoroantimonate(TASHFA), and triarylsulfonium hexafluorophosphate(TASHFP) as initiators were used in this study. The chemical and mechanical characteristics of irradiated epoxy resins were compared after curing of E-beam and {gamma}-ray irradiation up to 50 kGy in N{sub 2} and air atmosphere. We ascertained the effect of oxygen on the radiation curing of epoxy resin. The thermal properties of cured epoxy were investigated using DMA and TGA. Mechanical properties such as flexural strength were measured. The chemical structures of cured epoxy were characterized by FT-NIR. The gel fraction and the stress at yield of epoxy resins irradiated by E-beam and {gamma}-ray in N{sub 2} atmosphere were also compared with those of epoxy resins irradiated by E-beam and {gamma}-ray in air.

Versatile composite resins simplifying the practice of restorative dentistry.

Science.gov (United States)

Margeas, Robert

2014-01-01

After decades of technical development and refinement, composite resins continue to simplify the practice of restorative dentistry, offering clinicians versatility, predictability, and enhanced physical properties. With a wide range of products available today, composite resins are a reliable, conservative, multi-functional restorative material option. As manufacturers strive to improve such properties as compression strength, flexural strength, elastic modulus, coefficient of thermal expansion, water sorption, and wear resistance, several classification systems of composite resins have been developed.

The effect of soda immersion on nano hybrid composite resin discoloration

Directory of Open Access Journals (Sweden)

M. Chair Effendi

2014-03-01

Full Text Available Background: Composite resin is the tooth-colored restorative material which most of the people are fond of due to their aesthetic value. The composite resin discoloration may happen because of the intrinsic and extrinsic factors. Soda water is one of the beverages which can cause the composite resin discoloration. Purpose: The study was aimed to determine the effect of soda immersion on nano hybrid composite resin discoloration. Methods: The study was an experimental laboratory study using 100 shade A3 nano hybrid composite resin specimens with the diameter of 5 mm and density of 2mm. The samples were divided into 5 groups, each group was immersed in different beverages. The beverages were mineral water; lemon-flavored soda; strawberry-flavored soda; fruit punch-flavored soda; and orange-flavored soda for 3, 7, 14 and 21 days respectively, in the temperature of 37o C. The discoloration measurement utilizes Spectrophotometer, Vita Easy Shade, and uses CIEL*a*b* method. Results: The result showed that the duration of immersion in soda had an effect on the Nano hybrid composite resin discoloration. Strawberry and fruit punch- flavored soda were the most influential components toward the discoloration. Nevertheless, the generally-occurred discoloration was clinically acceptable (∆E ≤ 3,3. Conclusion: The study suggested that the soda immersion duration has effect on Nano hybrid composite resin discoloration.Latar belakang: Resin komposit adalah material sewarna gigi yang diminati masyarakat karena memiliki nilai estetik yang baik. Perubahan warna resin komposit dapat terjadi karena faktor intrinsik dan ekstrinsik. Minuman soda merupakan salah satu minuman yang dapat menyebabkan perubahan warna pada resin komposit. Tujuan: Tujuan dari penelitian ini untuk meneliti perubahan warna resin komposit nanohibrida akibat perendaman dalam minuman soda. Metode: Metode yang digunakan pada penelitian ini adalah eksperimental laboratorik dengan menggunakan

Synthesis of adhesive radiohardenable resins of the modified polyepoxide type

International Nuclear Information System (INIS)

Acquacalda, J.-M.

1972-01-01

Eight adhesive radiohardenable resins of the modified epoxide type have been synthesized. Four were obtained from commercial resins: EPON 812, 827, 871 and ARALDITE 106. The synthesis of the four others required the development of analytical techniques to characterize of the reagents beforehand and then to identify the resins themselves. From a study of behavior under irradiation it seems that all the compounds obey a law of acrylic double bond disappearance with the logarithm of irradiation dose for which it is hard to find a detailed theoretical interpretation. The fracture of irradiated adhesive assemblies and their comparison has shown that for acceptable irradiation doses the synthesized resins, especially the product of Bisphenol A condensation on glycidyl acrylate, behave quite as well as polyepoxide resins without possessing the disadvantages inherent to the incorporation of standard chemical hardeners [fr

Recovery of value-added fossil resin from El-Maghara coal

Energy Technology Data Exchange (ETDEWEB)

Ibrahim, S.S.; Mostafa, S.I. [Central Metallurgical R and D Inst., Cairo (Egypt)

2003-06-01

El-Maghara coal was confirmed to contain a substantial amount of fossil resin intimately associated with its macerals. Macroscopic identification as well as physical diagnosis of solvent refined resinite material proved its particular significance and sufficient value to justify a fossil resin industry in Egypt. This resin has thermosetting properties superior to most synthetics resins available from petrochemicals. It could compete in the market as a chemical commodity in high-speed printing and high-performance adhesive applications. It could have also special values as a feedstock for high-density jet fuel after proper hydrogenation. The froth flotation technique was applied to recover this valuable material from El-Maghara ground coal. The solvent extraction method using commercial solvents was used to refine the resinite fraction collected as flotation concentrate. The variables affecting the flotation technique were studied. Characterization of refined resin was applied. (orig.)

Impregnation of soft biological specimens with thermosetting resins and elastomers.

Science.gov (United States)

von Hagens, G

1979-06-01

A new method for impregnation of biological specimens with thermosetting resins and elastomers is described. The method has the advantage that the original relief of the surface is retained. The impregnation is carried out by utilizing the difference between the high vapor tension of the intermedium (e.g., methylene chloride) and the low vapor tension of the solution to be polymerized. After impregnation, the specimen is subject to polymerization conditions without surrounding embedding material. The optical and mechanical properties can be selected by proper choice from various kinds of resins and different procedures, for example, by complete or incomplete impregnation. Acrylic resins, polyester resins, epoxy resins, polyurethanes and silicone rubber have been found suitable for the method. Excellent results have been obtained using transparent silicone rubber since after treatment the specimens are still flexible and resilient, and have retained their natural appearance.

Stress and flow analyses of ultraviolet-curable resin during curing

Science.gov (United States)

Umezaki, Eisaku; Okano, Akira; Koyama, Hiroto

2014-06-01

The stress and flow generated in ultraviolet (UV)-curable resin during curing in molds were measured to investigate their relationship. The specimens were molds consisting of glass plates and acrylic bars, and UV-curable liquid resin. The specimens were illuminated from above with UV rays. Photoelastic and visual images were separately obtained at a constant time interval using cameras during curing. To help obtain the visual images, acrylic powder was mixed with the liquid resin. The stress was obtained from the photoelastic images by a digital photoelastic technique with phase stepping, and the flow was obtained from the visual images by a particle-tracking velocimetry technique. Results indicate that the stress generated in the UV-curable resin during curing depends on the degree of contact between the mold and the cured area of the resin, and is hardly related to the flow.

The purification by ion exchange resins of the heavy water la the reactors EL1 and EL2. B - study of the general properties of the resins used; Purification par resines echangeuses d'ions de l'eau lourde de reacteurs EL1 et EL2. B - etude des proprietes generales des resines utilisees

Energy Technology Data Exchange (ETDEWEB)

Fourre,; Platzer, [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1957-07-01

Within the programme of the pile heavy water purification project, organized by the stable Isotopes Section, we have carried out a certain number of tests on ion exchange resins. The problem posed by the stable Isotopes Section was to determine the conditions of utilisation of ion exchange resins, knowing that they would be employed in a system branching off the heavy water circuit in the piles. These investigations were carried out in close collaboration with the stable Isotopes Section, and were guided chiefly by the extremely short delay permitted between the laboratory study and its application to the piles. The tests are divided into two groups: 1- General properties of the resins. 2- Utilisation of the resins, particularly in an apparatus similar to those mounted on the piles but of smaller dimensions. (author) [French] Dans le cadre du projet d'epuration de l'eau lourde des piles, traite par la Section des Isotopes stables, nous avons fait un certain nombre d'essais sur les resines echangeuses d'ions. Le probleme pose par la Section des Isotopes stables etait de determiner les conditions d'utilisation des resines echangeuses d'ions sachant qu'elles devraient etre employees dans un appareil place en derivation sur le circuit d'eau lourde des piles. L'ensemble de l'etude a ete mene en collaboration etroite avec la Section des Isotopes stables et a ete guide principalement par le delai extremement court dans lequel l'etude de laboratoire devait etre appliquee aux piles. Les essais se divisent en deux groupes: 1- Proprietes generales des resines. 2- Utilisation des resines, en particulier dans un appareil analogue a ceux montes sur les piles, mais de dimensions reduites. (auteur)

Photopolymerizable silicone monomers, oligomers, and resins

International Nuclear Information System (INIS)

Jacobine, A.F.; Nakos, S.T.

1992-01-01

The purpose of this chapter is to acquaint the general photopolymer researcher with the historical development of the chemistry and technology of photopolymerizable silicone monomers, fluids, and resins. The current status of research in these areas is assessed. The focus of this chapter is not only on the polymer chemistry and application of this technology, but also on important aspects of the synthetic chemistry involved in the preparation of UV-curable silicone monomers, oligomers, and resins. 236 refs., 6 tabs

Device for processing regenerative wastes of ion exchange resin

International Nuclear Information System (INIS)

Kuroda, Osamu; Ebara, Katsuya; Shindo, Toshikazu; Takahashi, Sankichi

1986-01-01

Purpose: To facilitate the operation and maintenance of a processing device by dividing radioactive wastes produced in the regenerative process of ion exchange resin into a regenerated usable recovery liquid and wastes. Constitution: Sulfuric acid is recovered by a diffusion dialysis method from wastes containing sulfuric acid that are generated in the regenerative process of cation-exchange resin and also caustic soda is recovered by the diffusion dialysis method from wastes containing caustic soda that are generated in the regenerative process of anion-exchange resin. The sulfuric acid and caustic soda thus recovered are used for the regeneration of ion-exchange resin. A concentrator is provided for concentrating the sulfuric acid and caustic soda water solution to concentration suitable for the regeneration of these ion-exchange resins. Also provided is a recovery device for recovering water generated from the concentrator. This device is of so simple a constitution that its operation and maintenance can be performed very easily, thereby greatly reducing the quantity of waste liquid required to be stored in drums. (Takahashi, M.)

Electrodeposition properties of modified cational epoxy resin-type photoresist

International Nuclear Information System (INIS)

Yong He; Yunlong Zhang; Feipeng Wu; Miaozhen Li; Erjian Wang

1999-01-01

Multi-component cationic epoxy and acrylic resin system for ED photoresist was used in this work, since they can provide better storage stability for ED emulsion and better physical and chemical properties of deposited film than one-component system. The cationic main resin (AE) was prepared from amine modified epoxy resins and then treated with acetic acid. The amination degree was controlled as required. The synthetic procedure of cationic main resins is described in scheme I. The ED photoresist (AME) is composed of cationic main resin (AE) and nonionic multifunctional acrylic crosslinkers (PETA), in combination with suitable photo-initiator. They can easily be dispersed in deionized water to form a stable ED emulsion. The exposed part of deposited film upon UV irradiation occurs crosslinking to produce an insoluble semi-penetrating network and the unexposed part remains good solubility in the acidic water solution. It is readily utilized for fabrication of fine micropattern. The electrodeposition are carried out on Cu plate at room temperature. To evaluate the electrodeposition properties of ED photoresist (AME), the different influences are examined

Selective separation of indium by iminodiacetic acid chelating resin

International Nuclear Information System (INIS)

Fortes, M.C.B.; Benedetto, J.S.; Martins, A.H.

2007-01-01

- Indium can be recovered by treating residues, flue dusts, slags, and metallic intermediates in zinc smelting. This paper investigates the adsorption characteristics of indium and iron on an iminodiacetic acid chelating resin, Amberlite R IRC748 (Rohm and Haas Co.-USA). High concentrations of iron are always present in the aqueous feed solution of indium recovery. In addition, the chemical behaviour of iron in adsorptive systems is similar to that of indium. The metal concentrations in the aqueous solution were based on typical indium sulfate leach liquor obtained from zinc hydrometallurgical processing in a Brazilian plant. The ionic adsorption experiments were carried out by the continuous column method. Amberlite R IRC748 resin had a high affinity for indium under acidic conditions. Indium ions adsorbed onto the polymeric resin were eluted with a 0.5 mol/dm 3 sulphuric acid solution passed through the resin bed in the column. 99.5% pure indium sulfate aqueous solution was obtained using the iminodiacetic acid chelating resin Amberlite R IRC748. (author)

Terpenoid composition and class of Tertiary resins from India

Energy Technology Data Exchange (ETDEWEB)

Dutta, Suryendu; Mallick, Monalisa; Mathews, Runcie Paul [Department of Earth Sciences, Indian Institute of Technology Bombay, Powai, Mumbai-400076 (India); Bertram, Norbert [LTA-Labor fuer Toxikologie und Analytik, Friedrichshoeher Str. 28, D-53639 Koenigswinter (Germany); Greenwood, Paul F. [John De Laeter Mass Spectrometry and WA Biogeochemitry Centres (M090), The University of Western Australia, 35 Stirling Hwy, Crawley, WA, 6009 (Australia); WA - Organic and Isotope Geochemistry Centre, Curtin University of Technology, Kent St., Bentley 6102 (Australia)

2009-10-01

The terpenoid composition and class of Tertiary resins preserved within lignites of Cambay, Kutch and Cauvery Basins of India have been characterized using Pyrolysis-Gas Chromatography-Mass Spectrometry (Py-GC-MS) and Fourier Transform Infrared (FTIR) Spectroscopy. Major pyrolysis products include cadalene-based C{sub 15}-bicyclic sesquiterpenoids with some C{sub 30} and C{sub 31} bicadinanes and bicadinenes typical of Class II or dammar resin. The occurrence of these terpenoids in Early Eocene sediments may extend the first appearance of Dipterocarpaceae angiosperms, the predominant source of this resin class, back to the Early Eocene epoch in India. The same terpenoid biomarkers have been detected in many SE Asian oils reflecting a close source relationship with these resins. Strong CH{sub 3} (1377 cm{sup -} {sup 1}) and other CH{sub x} (3000-2800 and 1460-1450 cm{sup -} {sup 1}) aliphatic absorptions of much larger intensity than the aromatic C = C (1560-1650 cm{sup -} {sup 1}) absorption were detected in the Indian resins by FTIR Spectroscopy, confirming the quantitative significance of the terpenoid pyrolysates. (author)

Wear Resistance of 3D Printing Resin Material Opposing Zirconia and Metal Antagonists.

Science.gov (United States)

Park, Ji-Man; Ahn, Jin-Soo; Cha, Hyun-Suk; Lee, Joo-Hee

2018-06-20

3D printing offers many advantages in dental prosthesis manufacturing. This study evaluated the wear resistance of 3D printing resin material compared with milling and conventional resin materials. Sixty substrate specimens were prepared with three types of resin materials: 3D printed resin, milled resin, and self-cured resin. The 3D printed specimens were printed at a build angle of 0° and 100 μm layer thickness by digital light processing 3D printing. Two kinds of abraders were made of zirconia and CoCr alloy. The specimens were loaded at 5 kg for 30,000 chewing cycles with vertical and horizontal movements under thermocycling condition. The 3D printed resin did not show significant difference in the maximal depth loss or the volume loss of wear compared to the milled and the self-cured resins. No significant difference was revealed depending on the abraders in the maximal depth loss or the volume loss of wear. In SEM views, the 3D printed resin showed cracks and separation of inter-layer bonds when opposing the metal abrader. The results suggest that the 3D printing using resin materials provides adequate wear resistance for dental use.

Purification of degraded TBP solvent using macroreticular anion exchange resin

International Nuclear Information System (INIS)

Kartha, P.K.S.; Kutty, P.V.E.; Janaradanan, C.; Ramanujam, A.; Dhumwad, R.K.

1989-01-01

Tri-n-butyl phosphate (TBP) diluted with a suitable diluent is commonly used for solvent extraction in Purex process for the recovery of uranium and plutonium from irradiated nuclear fuels. This solvent gets degraded due to various factors, the main degradation product being dibutyl phosphoric acid (HDBP). A solvent cleanup step is generally incorporated in the process for removing the degradation products from the used solvent. A liquid-liquid cleanup system using sodium carbonate or sodium hydroxide solution is routinely used. Considering certain advantages, like the possibility of loading the resin almost to saturation capacity and the subsequent disposal of the spent resin by incineration and the feasibility of adopting it to the process, a liquid-solid system has been tried as an alternate method, employing various available macroreticular anion exchange resins in OH - form for the sorption of HDBP from TBP. After standardizing the various conditions for the satisfactory removal of HDBP from TBP using synthetic mixtures, resins were tested with process solvent in batch contacts. The parameters studied were (1) capacity of different resins for HDBP sorption (2) influence of acidity, uranium and HDBP on the sorption behaviour of the latter (3) removal of fission products from the solvent by the resin and (4) regeneration and recycling of the resin. (author). 2 figs., 13 tabs., 17 refs

Antimicrobial activity of Dracaena cinnabari resin from Soqotra ...

African Journals Online (AJOL)

Background: Few studies showed that Dracaena cinnabari resin, collected from Soqotra Island, Yemen, has antimicrobial activity. This study is the first to investigate antimicrobial activity of the resin on both antibiotic multi-resistant human pathogens and on poly-microbial culture. Material and Methods: Antimicrobial activity ...

Polyphenolic resin synthesis: optimizing plantain peel biomass as heavy metal adsorbent

Directory of Open Access Journals (Sweden)

Andrés Felipe Cordero

2015-08-01

Full Text Available AbstractPolyphenolic resol resins were obtained from an ethanolic extraction of green plantain peels (Musa paradisiaca grown in Colombia. A synthesis was then performed by polycondensation in an alkaline pH solution in order to perform research on phenolic resin production with high mechanical performance. The polymers were characterized by DSC and TGA analyses and the resins showed a melting point of 94 °C and the typical properties of resol resins. Moreover, the synthesis was controlled using the infrared technique (FTIR where different organic functional groups present in the polymers obtained are observed. The obtained resins were used as heavy metal adsorbents in which the content of those toxic agents is measured by Atomic Absorption Analysis (AA indicating that these resins have a high retention affinity to Pb+2, Ni+2 and Cr+3 (79.01%, 98.48%, 94.14%, respectively as determined by Freundlich isotherms.

Chemoviscosity modeling for thermosetting resin systems, part 3

Science.gov (United States)

Hou, T. H.; Bai, J. M.

1988-01-01

A new analytical model for simulating chemoviscosity resin has been formulated. The model is developed by modifying the well established Williams-Landel-Ferry (WLF) theory in polymer rheology for thermoplastic materials. By introducing a relationship between the glass transition temperature (T sub g (t)) and the degree of cure alpha(t) of the resin system under cure, the WLF theory can be modified to account for the factor of reaction time. Temperature-dependent functions of the modified WLF theory parameters C sub 1 (T) and C sub 2 (T) were determined from the isothermal cure data. Theoretical predictions of the model for the resin under dynamic heating cure cycles were shown to compare favorably with the experimental data. This work represents a progress toward establishing a chemoviscosity model which is capable of not only describing viscosity profiles accurately under various cure cycles, but also correlating viscosity data to the changes of physical properties associated with the structural transformations of the thermosetting resin systems during cure.

Thermal behaviour of used resin during conditioning process

International Nuclear Information System (INIS)

Arsene, C.

2016-01-01

In the nuclear power plants using light water and heavy water as coolant, as well as in most waste treatment installations, the ion-exchange resins are used to purify water circuits. Since the resins retain both radionuclide and chemical impurities, it represents a low- and intermediate- radioactive waste that requires special management for storage and disposal. From experimental studies it was found that the conditioning of the used resin in bitumen has several advantages. But there are some disadvantages, too, one being the significant amount of gas produced during the bituminization process because of the high temperature (1200C). Besides water vapours, the condensable gas mixture (formed by a liquid fraction and an oil fraction) contains products generated from the partial decomposition of the resin and release of degradation products of bitumen: dimethyl and trimethylamine, methanol - compounds resulting from the destruction of functional groups and hydrocarbon fraction formed by n-paraffins (C6-C32), iso-paraffins and aromatics. (authors)

A qualitative chemometric study of resin composite polymerization

Directory of Open Access Journals (Sweden)

Regina Ferraz Mendes

2008-01-01

Full Text Available Objective: An experiment was carried out to assess the effect produced by different polymerization techniques on resin composite color after it has been immersed in coffee. Methods: Samples were manufactured using TPH Spectrum composite. It was polymerized for 10 or 40 seconds, with the light tip at one or zero millimeters from the resin surface, and afterwards the samples were immersed in coffee for 24 hours or 7 days. Ten different evaluators classified the samples according to their degree of staining. Results: The samples that were polymerized for 10 seconds were more susceptible to staining than the ones polymerized by 40 seconds. Samples immersed in coffee for 7 days were more susceptible to staining than the ones immersed for 24 hours. Conclusion: The variables polymerization time and immersion time were determinant in the staining susceptibility of the studied composite by coffee. However, there was no significant difference, irrespective of whether the resin was polymerized 10 or zero millimeters away from the resin surface.

Optical emission behavior and radiation resistance of epoxy resins

International Nuclear Information System (INIS)

Kawanishi, Shunichi; Udagawa, Akira; Hagiwara, Miyuki

1987-11-01

To make clear a mechanism of radiation resistance of epoxy resin systems, a role of energy trapping site induced in bisphenol A type epoxy resins cured with 4 kinds of aromatic amines (Φ N ) was studied in comparison with the case of aliphatic amine curing system through a measurement of optical emission. In the system of the epoxy resin cured with DETA, the optical emission from an excited state of bisphenol A unit of epoxy resin and a charge transfer complex was observed. On the other hand, the optical emission from Φ N was observed in the aromatic amine curing system. Their excitation spectrum consists of peaks of absorption spectrum of BA and those of Φ N , showing that the excited state of Φ N is formed through the excitation of both BA and Φ N . Therefore, the excited energy of BA transfers to the excited state of Φ N . Emission intensity of Φ N band was 20 ∼ 100 times as large as that of BA. These results indicate that the radiation energy is effectively released as an optical emission from excited state of Φ N in the epoxy resin when cured with aromatic amine. It can be concluded from the above results that aromatic amine hardeners contribute to enhancement of the radiation resistance of epoxy resin by acting as an energy transfer agent. (author)

Analysis of surface hardness of artificially aged resin composites

Directory of Open Access Journals (Sweden)

Denise Cremonezzi Tornavoi

2012-02-01

Full Text Available This study evaluated the effect of artificially accelerated aging (AAA on the surface hardness of eight composite resins: Filtek Z250, Filtek Supreme, 4 Seasons, Herculite, P60, Tetric Ceram, Charisma, and Filtek Z100. Sixteen specimens were made from the test piece of each material, using an 8.0 × 2.0 mm teflon matrix. After 24 hours, eight specimens from each material were submitted to three surface hardness readings using a Shimadzu Microhardness Tester for 5 seconds at a load of 50 gf. The other eight specimens remained in the artificially accelerated aging machine for 382 hours and were submitted to the same surface hardness analysis. The means of each test specimen were submitted to the Kolmogorov-Smirnov test (p > 0.05, ANOVA and Tukey test (p < 0.05. With regard to hardness (F = 86.74, p < 0.0001 the analysis showed significant differences among the resin composite brands. But aging did not influence the hardness of any of the resin composites (F = 0.39, p = 0.53. In this study, there was interaction between the resin composite brand and the aging factors (F = 4.51, p < 0.0002. It was concluded that notwithstanding the type of resin, AAA did not influence surface hardness. However, with regard to hardness there was a significant difference among the resin brands.

Temperature-dependence of creep behaviour of dental resin-composites.

Science.gov (United States)

El-Safty, S; Silikas, N; Watts, D C

2013-04-01

To determine the effect of temperature, over a clinically relevant range, on the creep behaviour of a set of conventional and flowable resin-composites including two subgroups having the same resin matrix and varied filler loading. Eight dental resin-composites: four flowable and four conventional were investigated. Stainless steel split moulds (4 mm × 6 mm) were used to prepare cylindrical specimens for creep examination. Specimens were irradiated in the moulds in layers of 2mm thickness (40s each), as well as from the radial direction after removal from the moulds, using a light-curing unit with irradiance of 650 mW/cm(2). A total of 15 specimens from each material were prepared and divided into three groups (n=5) according to the temperature; Group I: (23°C), Group II: (37°C) and Group III: (45°C). Each specimen was loaded (20 MPa) for 2h and unloaded for 2h. Creep was measured continuously over the loading and unloading periods. At higher temperatures greater creep and permanent set were recorded. The lowest mean creep occurred with GS and GH resin-composites. Percentage of creep recovery decreased at higher temperatures. At 23°C, the materials exhibited comparable creep. At 37°C and 45°C, however, there was a greater variation between materials. For all resin-composites, there was a strong linear correlation with temperature for both creep and permanent set. Creep parameters of resin-composites are sensitive to temperature increase from 23 to 45°C, as can occur intra-orally. For a given resin matrix, creep decreased with higher filler loading. Copyright © 2012 Elsevier Ltd. All rights reserved.

Elaboration of extracting, incinerable and/or conducting resins, for the grouped conversion of actinides; Conception de resines extractantes, incinerables et/ou conductrices, pour la conversion groupee d'actinides

Energy Technology Data Exchange (ETDEWEB)

Mokhtari, H. [Paris-11 Univ., 91 - Orsay (France)]|[CEA Valrho, Lab. de Chimie des Actinides (LCA), 30 - Marcoule (France)

2006-07-01

The first results obtained in the framework of the study called PEACE (Process for the Elaboration of Actinide Carbide from ion Exchange resin) concern the fixation of neodymium(III) (simulating trivalent actinides) on two carboxylic resins: the first one is of gel type and the second one of macroporous type. A kinetic study of the exchange NH{sub 4}{sup +}/Nd{sup 3+} has shown that: 1)neodymium is fixed under the form of a complexed or hydrolyzed specie of neodymium of charge 2+ 2)a high charge rate is reached (40% in mass for the dried resin which corresponds to an exchange capacity of 11 meq/g dry of introduced resin) 3)the exchange kinetics is better for the macroporous resin than for the gel resin. A heat treatment of the macroporous resin charged in neodymium has been carried out until the carbonization by the mean of thermal gravimetric analyses carried out under air and argon. A carbon/neodymium ratio of about 5 is obtained after carbonization under argon. Scanning electron microscopy analyses carried out on the macroporous resin charged in neodymium have revealed a conservation of the sphericity and a consequent reduction of the resin balls diameter after heat treatment and an homogeneous distribution of neodymium inside the sphere. (O.M.)

Competitive light absorbers in photoactive dental resin-based materials.

Science.gov (United States)

Hadis, Mohammed A; Shortall, Adrian C; Palin, William M

2012-08-01

The absorbance profile of photoinitiators prior to, during and following polymerization of light curable resin-based materials will have a significant effect on the cure and color properties of the final material. So-called "colorless" photoinitiators are used in some light-activated resin-based composite restorative materials to lessen the yellowing effect of camphoroquinone (CQ) in order to improve the esthetic quality of dental restorations. This work characterizes absorption properties of commonly used photoinitiators, an acylphosphine oxide (TPO) and CQ, and assesses their influence on material discoloration. Dimethacrylate resin formulations contained low (0.0134 mol/dm(3)), intermediate (0.0405 mol/dm(3)) or high (0.0678 mol/dm(3)) concentrations of the photoinitiators and the inhibitor, butylated hydroxytoluene (BHT) at 0, 0.1 or 0.2% by mass. Disc shaped specimens (n = 3) of each resin were polymerized for 60s using a halogen light curing unit. Dynamic measurements of photoinitiator absorption, polymer conversion and reaction temperature were performed. A spectrophotometer was used to measure the color change before and after cure. GLM three-way analysis of variance revealed significant differences (pphotoinitiator type (df = 1; F = 176.12)>% BHT (df = 2, F = 13.17). BHT concentration affected the rate of polymerization and produced lower conversion in some of the CQ-based resins. Significant differences between photoinitiator type and concentrations were seen in color (where TPO resins became yellower and camphoroquinone resins became less yellow upon irradiation). Reaction temperature, kinetics and conversion also differed significantly for both initiators (presins producing a visually perceptible color change upon polymerization, the color change was significantly less than that produced with CQ-based resins. Although some photoinitiators such as TPO may be a more esthetic alternative to CQ, they may actually cause significant color contamination when

Nanosilica Modification of Elastomer-Modified VARTM Epoxy Resins for Improved Resin and Composite Toughness

National Research Council Canada - National Science Library

Robinette, Jason; Bujanda, Andres; DeSchepper, Daniel; Dibelka, Jessica; Costanzo, Philip; Jensen, Robert; McKnight, Steven

2007-01-01

Recent publications have reported a synergy between rubber and silica in modified epoxy resins that results in significantly improved fracture toughness without reductions in other material properties...

Monitoring cure of composite resins using frequency dependent electromagnetic sensing techniques

Science.gov (United States)

Kranbuehl, D. E.; Hoff, M. S.; Loos, A. C.; Freeman, W. T., Jr.; Eichinger, D. A.

1988-01-01

A nondestructive in situ measurement technique has been developed for monitoring and measuring the cure processing properties of composite resins. Frequency dependent electromagnetic sensors (FDEMS) were used to directly measure resin viscosity during cure. The effects of the cure cycle and resin aging on the viscosity during cure were investigated using the sensor. Viscosity measurements obtained using the sensor are compared with the viscosities calculated by the Loos-Springer cure process model. Good overall agreement was obtained except for the aged resin samples.

Thermoset Blends of an Epoxy Resin and Polydicyclopentadiene

Energy Technology Data Exchange (ETDEWEB)

Rohde, Brian J.; Le, Kim Mai; Krishnamoorti, Ramanan; Robertson, Megan L.

2016-12-13

The mechanical properties of two chemically distinct and complementary thermoset polymers were manipulated through development of thermoset blends. The thermoset blend system was composed of an anhydride-cured diglycidyl ether of bisphenol A (DGEBA)-based epoxy resin, contributing high tensile strength and modulus, and polydicyclopentadiene (PDCPD), which has a higher toughness and impact strength as compared to other thermoset polymers. Ultra-small-angle and small-angle X-ray scattering analysis explored the morphology of concurrently cured thermoset blends, revealing a macroscopically phase separated system with a surface fractal structure across blended systems of varying composition. The epoxy resin rich and PDCPD rich phases exhibited distinct glass transitions (Tg’s): the Tg observed at higher temperature was associated with the epoxy resin rich phase and was largely unaffected by the presence of PDCPD, whereas the PDCPD rich phase Tg systematically decreased with increasing epoxy resin content due to inhibition of dicyclopentadiene ring-opening metathesis polymerization. The mechanical properties of these phase-separated blends were in reasonable agreement with predictions by the rule of mixtures for the blend tensile strength, modulus, and fracture toughness. Scanning electron microscopy analysis of the tensile and fracture specimen fracture surfaces showed an increase in energy dissipation mechanisms, such as crazing, shear banding, and surface roughness, as the fraction of the more ductile component, PDPCD, increased. These results present a facile method to tune the mechanical properties of a toughened thermoset network, in which the high modulus and tensile strength of the epoxy resin can be largely retained at high epoxy resin content in the blend, while increasing the fracture toughness.

Quantification and Purification of Mulberry Anthocyanins with Macroporous Resins

Directory of Open Access Journals (Sweden)

Xueming Liu

2004-01-01

Full Text Available Total anthocyanins in different cultivars of mulberry were measured and a process for the industrial preparation of mulberry anthocyanins as a natural food colorant was studied. In 31 cultivars of mulberry, the total anthocyanins, calculated as cyanidin 3-glucoside, ranged from 147.68 to 2725.46 mg/L juice. Extracting and purifying with macroporous resins was found to be an efficient potential method for the industrial production of mulberry anthocyanins as a food colorant. Of six resins tested, X-5 demonstrated the best adsorbent capability for mulberry anthocyanins (91 mg/mL resin. The adsorption capacity of resins increased with the surface area and the pore radius. Residual mulberry fruit juice after extraction of pigment retained most of its nutrients, except for anthocyanins, and may provide a substrate for further processing.

Preparation and characterization of antibacterial orthodontic resin containing silver nanoparticles

Science.gov (United States)

Lee, Sang Jin; Heo, Min; Lee, Donghyun; Han, Seungheui; Moon, Ji-Hoi; Lim, Ho-Nam; Kwon, Il Keun

2018-02-01

In this study, we developed a hybrid dental resin containing silver nanoparticle (AgNPs) to eliminate periodontal disease causing bacteria such as streptococcus mutans (S. mutans) and streptococcus sobrinus (S. sobrinus). The silver nanoparticles enables the resin to prevent oral pathogen growth during orthodontic therapy. First, AgNPs were directly synthesized in dimethylformamide (DMF) solvent with a capping agent. Second, pure orthodontic primer was mixed with the synthesized AgNPs solvent-slurry followed by photocuring. The resultant material was characterized by physicochemical characterization. Finally, an in vitro antimicrobial test was carried out. The results showed that the AgNPs were fully synthesized and clearly embedded in dental resin. In the bacterial test, the dental resin containing AgNPs showed potent antimicrobial activity against two kinds of bacteria. In conclusion, our methodology may allow for the generation of a wide range of dental resin and composite products which inhibit periodontitis causing bacteria.

Electro regeneration of iodide loaded resin. Contributed Paper RD-18

International Nuclear Information System (INIS)

Kumar, Ratnesh; Kumar, T.; Sree Kumar, B.; Seshadri, K.S.; Paul, Biplob

2014-01-01

Spent resins generated in the nuclear reactor contain essentially cationic activities due to Cesium, Strontium, Cobalt, and anionic activities due to Iodide, Iodate etc with activity loading to the extent of 0.1 Cim -3 and a surface dose of the order of 5 R. It is necessary to convert the spent resin into innocuous, reusable forms. An attempt has been made to regenerate Iodide containing spent resin into OH - electrolytically by using the OH - produced at the cathode compartment of an electrolytic cell. Results show that the regeneration of the spent resin containing Iodide could be completely accomplished electrolytically more efficiently than by addition of alkali. (author)

Comparison of stabilities in translucency, fluorescence and opalescence of direct and indirect composite resins.

Science.gov (United States)

Yu, Bin; Lee, Young-Keun

2013-01-01

To evaluate translucency, fluorescence and opalescence stabilities of direct and indirect composite resins after aging. One direct (16 shades) and two indirect composite resins (16 and 26 shades) were investigated. Resins were filled in a mold (1 mm thick) and light cured; post-curings were performed for indirect resins. Color was measured before and after 5,000 cycles of thermocycling on a reflection spectrophotometer in reflectance and transmittance modes to calculate parameters for translucency (TP), fluorescence (FL) and opalescence (OP). Differences in the changes of TP, FL and OP after aging by the type of resin were determined by t test, and those were also determined by one-way ANOVA with the factor of the brand or the shade group (P resins; and were -2.0 to 1.8, -0.9 to 0.4 and -2.9 to 3.7, respectively, for indirect resins. Changes in TP were not significantly different by the type of resin, but those in FL and OP were different (P = 0.05). Changes in optical parameters were influenced by the brand or the shade group of the resins (P resins varied depending on type, brand or shade group. Aging significantly affected fluorescence and opalescence, but not translucency, of indirect resins compared to those of direct resins.

Evaluating resin-enamel bonds by microshear and microtensile bond strength tests: effects of composite resin

Science.gov (United States)

de ANDRADE, Andrea Mello; MOURA, Sandra Kiss; REIS, Alessandra; LOGUERCIO, Alessandro Dourado; GARCIA, Eugenio Jose; GRANDE, Rosa Helena Miranda

2010-01-01

Objectives The aims of this study were to evaluate the effect of resin composite (Filtek Z250 and Filtek Flow Z350) and adhesive system [(Solobond Plus, Futurabond NR (VOCO) and Adper Single Bond (3M ESPE)] on the microtensile (µTBS) and microshear bond strength (µSBS) tests on enamel, and to correlate the bond strength means between them. Material and methods Thirty-six extracted human molars were sectioned to obtain two tooth halves: one for µTBS and the other one for µSBS. Adhesive systems and resin composites were applied to the enamel ground surfaces and light-cured. After storage (37ºC/24 h) specimens were stressed (0.5 mm/ min). Fracture modes were analyzed under scanning electron microscopy. The data were analyzed using two-way ANOVA and Tukey's test (α=0.05). Results The correlation between tests was estimated with Pearson's product-moment correlation statistics (α =0.05). For both tests only the main factor resin composite was statistically significant (padhesives. Both microbond tests seem to be positive and linearly correlated and can therefore lead to similar conclusions. PMID:21308290

A theoretical study of resin flows for thermosetting materials during prepreg processing

Science.gov (United States)

Hou, T. H.

1984-01-01

A flow model which describes the process of resin consolidation during prepreg lamination was developed. The salient features of model predictions were explored. It is assumed that resin flows in all directions originate from squeezing action between two approaching adjacent fiber/fabric layers. In the horizontal direction, a squeezing flow between two nonporous parallel plates is analyzed, while in the vertical direction a poiseuille type pressure flow through porous media is assumed. Proper force and mass balance was established for the whole system which is composed of these two types of flow. A flow parameter, CF, shows to be a measure of processibility for the curing resin. For a given external load-F the responses of resin flow during prepreg lamination, as measured by CF, are categorized into three regions: (1) the low CF region where resin flows are inhibited by the high chemoviscosity during initial curing stages; (2) the median CF region where resin flows are properly controllable; and (3) the high CF region where resin flows are ceased due to fiber/fabric compression effects. Resin losses in both directions are calculated. Potential uses of this model and quality control of incoming prepreg material are discussed.

Fatigue of the Resin-Enamel Bonded Interface and the Mechanisms of Failure

Science.gov (United States)

Yahyazadehfar, Mobin; Mutluay, Mustafa Murat; Majd, Hessam; Ryou, Heonjune; Arola, Dwayne

2013-01-01

The durability of adhesive bonds to enamel and dentin and the mechanisms of degradation caused by cyclic loading are important to the survival of composite restorations. In this study a novel method of evaluation was used to determine the strength of resin-enamel bonded interfaces under both static and cyclic loading, and to identify the mechanisms of failure. Specimens with twin interfaces of enamel bonded to commercial resin composite were loaded in monotonic and cyclic 4-point flexure to failure within a hydrated environment. Results for the resin-enamel interface were compared with those for the resin composite (control) and values reported for resin-dentin adhesive bonds. Under both modes of loading the strength of the resin-enamel interface was significantly (p≤0.0001) lower than that of the resin composite and the resin-dentin bonded interface. Fatigue failure of the interface occurred predominately by fracture of enamel, adjacent to the interface, and not due to adhesive failures. In the absence of water aging or acid production of biofilms, the durability of adhesive bonds to enamel is lower than that achieved in dentin bonding. PMID:23571321

Wear Resistance of 3D Printing Resin Material Opposing Zirconia and Metal Antagonists

Directory of Open Access Journals (Sweden)

Ji-Man Park

2018-06-01

Full Text Available 3D printing offers many advantages in dental prosthesis manufacturing. This study evaluated the wear resistance of 3D printing resin material compared with milling and conventional resin materials. Sixty substrate specimens were prepared with three types of resin materials: 3D printed resin, milled resin, and self-cured resin. The 3D printed specimens were printed at a build angle of 0° and 100 μm layer thickness by digital light processing 3D printing. Two kinds of abraders were made of zirconia and CoCr alloy. The specimens were loaded at 5 kg for 30,000 chewing cycles with vertical and horizontal movements under thermocycling condition. The 3D printed resin did not show significant difference in the maximal depth loss or the volume loss of wear compared to the milled and the self-cured resins. No significant difference was revealed depending on the abraders in the maximal depth loss or the volume loss of wear. In SEM views, the 3D printed resin showed cracks and separation of inter-layer bonds when opposing the metal abrader. The results suggest that the 3D printing using resin materials provides adequate wear resistance for dental use.

Catalytic oxidative pyrolysis of spent organic ion exchange resins from nuclear power plants

International Nuclear Information System (INIS)

Sathi Sasidharan, N.; Deshingkar, D.S.; Wattal, P.K.; Shirsat, A.N.; Bharadwaj, S.R.

2005-08-01

The spent IX resins from nuclear power reactors are highly active solid wastes generated during operations of nuclear reactors. Catalytic oxidative pyrolysis of these resins can lead to high volume reduction of these wastes. Low temperature pyrolysis of transition metal ion loaded IX resins in presence of nitrogen was carried out in order to optimize catalyst composition to achieve maximum weight reduction. Thermo gravimetric analysis of the pyrolysis residues was carried out in presence of air in order to compare the oxidative characteristics of transition metal oxide catalysts. Copper along with iron, chromium and nickel present in the spent IX resins gave the most efficient catalyst combination for catalytic and oxidative pyrolysis of the residues. During low temperature catalytic pyrolysis, 137 Cesium volatility was estimated to be around 0.01% from cationic resins and around 0.1% from anionic resins. During oxidative pyrolysis at 700 degC, nearly 10 to 40% of 137 Cesium was found to be released to off gases depending upon type of resin and catalyst loaded on to it. The oxidation of pyrolytic residues at 700 degC gave weight reduction of 15% for cationic resins and 93% for anionic resins. Catalytic oxidative pyrolysis is attractive for reducing weight and volume of spent cationic resins from PHWRs and VVERs. (author)

Resin-Bonded Bridges in vitro and in vivo

NARCIS (Netherlands)

Veen, Johannes Hilbrandt van der

1988-01-01

In this thesis in vitro and in vivo studies on the clinical application of resin-bonded bridges are described and discussed. The development of different types of resin-bonded bridges is described in chapter 1. The bridges are often made by boding a cast metal retainer fitted with and artificial

Fiber-reinforced Composite Resin Prosthesis to Restore Missing ...

African Journals Online (AJOL)

A fiber-reinforced composite inlay-onlay FPD was used for a single posterior tooth replacement in a patient refusing implant for psychological reasons. The FRC-FPD was made of pre-impregnated E-glass fibers (everStick, StickTeck, Turku, Finland) embedded in a resin matrix (Stick Resin, StickTeck, Turku, Finland).

Arthropods in modern resins reveal if amber accurately recorded forest arthropod communities.

Science.gov (United States)

Solórzano Kraemer, Mónica M; Delclòs, Xavier; Clapham, Matthew E; Arillo, Antonio; Peris, David; Jäger, Peter; Stebner, Frauke; Peñalver, Enrique

2018-05-07

Amber is an organic multicompound derivative from the polymerization of resin of diverse higher plants. Compared with other modes of fossil preservation, amber records the anatomy of and ecological interactions between ancient soft-bodied organisms with exceptional fidelity. However, it is currently suggested that ambers do not accurately record the composition of arthropod forest paleocommunities, due to crucial taphonomic biases. We evaluated the effects of taphonomic processes on arthropod entrapment by resin from the plant Hymenaea , one of the most important resin-producing trees and a producer of tropical Cenozoic ambers and Anthropocene (or subfossil) resins. We statistically compared natural entrapment by Hymenaea verrucosa tree resin with the ensemble of arthropods trapped by standardized entomological traps around the same tree species. Our results demonstrate that assemblages in resin are more similar to those from sticky traps than from malaise traps, providing an accurate representation of the arthropod fauna living in or near the resiniferous tree, but not of entire arthropod forest communities. Particularly, arthropod groups such as Lepidoptera, Collembola, and some Diptera are underrepresented in resins. However, resin assemblages differed slightly from sticky traps, perhaps because chemical compounds in the resins attract or repel specific insect groups. Ground-dwelling or flying arthropods that use the tree-trunk habitat for feeding or reproduction are also well represented in the resin assemblages, implying that fossil inclusions in amber can reveal fundamental information about biology of the past. These biases have implications for the paleoecological interpretation of the fossil record, principally of Cenozoic amber with angiosperm origin.

Pengaruh Minuman Kopi terhadap Perubahan Warna pada Resin Komposit

OpenAIRE

Aprilia Aprilia; Linda Rochyani; Erry Rahardianto

2015-01-01

Objective: The aim of this research was to investigate the influence of coffee beverage on hybrid composite resin discoloration. Material and method: This study used hybrid composite resin with A3 color, and was done by soaking composite resin plates in coffee solution for 1, 3, 5, and 7 days, corresponding to equivalent coffee usage for 6 months, 1, 1.5, and 2 years. The same measurements of reflectance were done before and after soaking into coffee solution. In the measurement, a beam from ...

Phenolic cation exchange resin material for recovery of cesium and strontium

Science.gov (United States)

Ebra, Martha A.; Wallace, Richard M.

1983-01-01

A phenolic cation exchange resin with a chelating group has been prepared by reacting resorcinol with iminodiacetic acid in the presence of formaldehyde at a molar ratio of about 1:1:6. The material is highly selective for the simultaneous recovery of both cesium and strontium from aqueous alkaline solutions, such as, aqueous alkaline nuclear waste solutions. The organic resins are condensation polymers of resorcinol and formaldehyde with attached chelating groups. The column performance of the resins compares favorably with that of commercially available resins for either cesium or strontium removal. By combining Cs.sup.+ and Sr.sup.2+ removal in the same bed, the resins allow significant reduction of the size and complexity of facilities for processing nuclear waste.

Cost effectiveness of detritiating water with resin columns

International Nuclear Information System (INIS)

Drake, R.H.; Williams, D.S.

1997-10-01

There are technologies in use for cleaning up concentrated tritiated process water. These are not cost effective for tritiated water with low concentrations of tritium. There are currently no cost-effective technologies for cleaning up low-tritium-concentration tritiated water, such as most tritiated groundwater, spent fuel storage basin water, or underground storage tank water. Resin removal of tritium from tritiated water at low concentrations (near the order of magnitude of drinking water standard maximums) is being tested on TA-SO (Los Alamos National Laboratory's Liquid Radioactive Waste Treatment Facility) waste streams. There are good theoretical and test indications that this may be a technologically effective means of removing tritium from tritiated water. Because of likely engineering design similarity, it is reasonable to anticipate that a resin column system's costs will be similar to some common commercial water treatment systems. Thus, the potential cost effectiveness of a resin treatment system offers hope for treating tritiated water at affordable costs. The TA-50 resin treatment cost projection of $18 per 1,000 gallons is within the same order of magnitude as cost data for typical commercial groundwater cleanup projects. The prospective Los Alamos National Laboratory (LANL) resin treatment system at $18 per 1,000 gallons appears to have a likely cost advantage of at least an order of magnitude over the competing, developmental, water detritiation technologies

Salivary bisphenol A levels and their association with composite resin restoration.

Science.gov (United States)

Lee, Jung-Ha; Yi, Seung-Kyoo; Kim, Se-Yeon; Kim, Ji-Soo; Son, Sung-Ae; Jeong, Seung-Hwa; Kim, Jin-Bom

2017-04-01

Composite resin has been increasingly used in an effort to remove minimal amount of tooth structure and are used for restoring not just carious cavities but also cervical abrasion. To synthesize composite resin, bisphenol A (BPA) is used. The aim of the study was to measure the changes in salivary BPA level related with composite resin restoration. ELISA was used to examine the BPA levels in the saliva collected from 30 volunteers whose teeth were filled with composite resin. Salivary samples were collected immediately before filling and 5 min and 7 d after filling. Wilcoxon signed-ranks test and linear regression were performed to test the significant differences of the changes in BPA levels in saliva. Before a new composite resin filling, there was no significant difference between with and without existing filling of composite resin and BPA level in the saliva was not correlated to the number of filled surfaces with composite resin. However, BPA level in the saliva increased to average 3.64 μg/L from average 0.15 μg/L after filling 5 min. BPA level increased in proportion with the number of filled surfaces. BPA level decreased to average 0.59 after filling 7 d. However it was higher than the BPA level before a new composite resin filling. Considering 50 μg/kg/day as the Tolerable Daily Intake of BPA suggested by European Food Safety Authority, the amount of BPA eluted in saliva after the composite resin filling is considered a safe level that is not a hazard to health at all. Copyright © 2016 Elsevier Ltd. All rights reserved.

Resin infusion of large composite structures modeling and manufacturing process

Energy Technology Data Exchange (ETDEWEB)

Loos, A.C. [Michigan State Univ., Dept. of Mechanical Engineering, East Lansing, MI (United States)

2006-07-01

The resin infusion processes resin transfer molding (RTM), resin film infusion (RFI) and vacuum assisted resin transfer molding (VARTM) are cost effective techniques for the fabrication of complex shaped composite structures. The dry fibrous preform is placed in the mold, consolidated, resin impregnated and cured in a single step process. The fibrous performs are often constructed near net shape using highly automated textile processes such as knitting, weaving and braiding. In this paper, the infusion processes RTM, RFI and VARTM are discussed along with the advantages of each technique compared with traditional composite fabrication methods such as prepreg tape lay up and autoclave cure. The large number of processing variables and the complex material behavior during infiltration and cure make experimental optimization of the infusion processes costly and inefficient. Numerical models have been developed which can be used to simulate the resin infusion processes. The model formulation and solution procedures for the VARTM process are presented. A VARTM process simulation of a carbon fiber preform was presented to demonstrate the type of information that can be generated by the model and to compare the model predictions with experimental measurements. Overall, the predicted flow front positions, resin pressures and preform thicknesses agree well with the measured values. The results of the simulation show the potential cost and performance benefits that can be realized by using a simulation model as part of the development process. (au)

Evaluation of ferrocyanide anion exchange resins regarding the uptake of Cs+ ions and their regeneration

International Nuclear Information System (INIS)

Won, Hui Jun; Mooon, Jei Kwon; Jung, Chong Hun; Chung, Won Yang

2008-01-01

Ferrocyanide-anion exchange resin was prepared and the prepared ion exchange resins were tested on the ability to uptake Cs + ion. The prepared ion exchange resins were resin-KCoFC, resin-KNiFC, and resin-KCuFC. The three tested ion exchange resins showed ion exchange selectivity on the Cs + ion of the surrogate soil decontamination solution, and resin- KCoFC showed the best Cs + ion uptake capability among the tested ion exchange resins. The ion exchange behaviors were explained well by the modified Dubinin-Polanyi equation. A regeneration feasibility study of the spent ion exchange resins was also performed by the successive application of hydrogen peroxide and hydrazine. The desorption of the Cs + ion from the ion exchange resin satisfied the electroneutrality condition in the oxidation step; the desorption of the Fe 2+ ion in the reduction step could also be reduced by adding the K + ion

[The endo-exo prosthesis for patients with a problematic amputation stump].

Science.gov (United States)

Frölke, Jan Paul M; van de Meent, Henk

2010-01-01

Following lower limb amputation, quality of life is highly related to the ability to use a prosthetic limb. The conventional way to attach a prosthetic limb to the body is with a socket. Many patients experience serious discomfort wearing a conventional prosthesis because of pain, instability during walking, pressure sores, bad smell or skin irritation. In addition, sitting is uncomfortable and pelvic and lower back pain due to unstable gait is often seen in these patients. The main disadvantage of the current prosthesis is the attachment of a rigid prosthesis socket to a soft and variable body. The socket must fit tightly for stability during walking but should also be comfortable for sitting. The implantation of an osseointegrated, intramedullary, transcutaneously conducted prosthesis is a new procedure for attaching a limb prosthesis to the human body without the disadvantages of the conventional prosthesis. The intramedullary prosthesis is designed with a rough surface resembling cancellous bone to enable a secure solid integration with the long bone. We treated two patients with this new prosthesis, a 44-year-old man after a transfemoral amputation, and a 32-year-old woman after a lower leg amputation; both amputations were necessary because of trauma. Those two patients are now, more than one year after the operation, showing excellent functional results without infectious complications. We assume that endo-exo prosthesis may be a promising option for selected patients unable to use a conventional prosthesis because of a problematic amputation stump.

21 CFR 181.26 - Drying oils as components of finished resins.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Drying oils as components of finished resins. 181... Prior-Sanctioned Food Ingredients § 181.26 Drying oils as components of finished resins. Substances classified as drying oils, when migrating from food-packaging material (as components of finished resins...

Pyrolysis and oxidative pyrolysis experiments with organization exchange resin

International Nuclear Information System (INIS)

Chun, Ung Kyung

1997-01-01

Pyrolysis may be an important pretreatment step before vitrification in a cold crucible melter (CCM). During vitrification of organic resin the carbon or other remaining residues may harm the performance of the cold crucible melter of the eventual stability of the final glass product. Hence, it is important to reduce or prevent such harmful waste from entry into the cold crucible melter. Pretreatment with pyrolysis will generally provide volume reduction resulting in less amount of solid waste that needs to be handled by the CCM; in addition, the pyrolytic processes may breakdown much of the complex organics causing release through volatilization resulting in less carbon and other harmful substances. Hence, KEPRI has undertaken studies on the pyrolysis and oxidative pyrolysis of organic ion exchange resin. Pyrolysis and oxidative pyrolysis were examined with TGA and a tube furnace. TGA results for pyrolysis with the flow of nitrogen indicate that even after pyrolyzing from room temperature to about 900 deg C, a significant mass fraction of the original cationic resin remains, approximately 46 %. The anionic resin when pyrolytically heated in a flow of nitrogen only, from room temperature to about 900 deg C, produced a final residue mass fraction of about 8 percent. Oxidation at a ratio of air to nitrogen, 1:2, reduced the cationic resin to 5.3% when heated at 5 C/min. Oxidation of anionic resin at the same ratio and same heating rate left almost no solid residue. Pyrolysis (e.g. nitrogen-only environment) in the tube furnace of larger samples relative to the TGA produced very similar results to the TGA. The differences may be attributed to the scale effects such as surface area exposure to the gas stream, temperature distributions throughout the resin, etc. (author) 7 refs., 7 figs

Pyrolysis and oxidative pyrolysis experiments with organization exchange resin

Energy Technology Data Exchange (ETDEWEB)

Chun, Ung Kyung [Korea Electric Power Research Insititute, Taejon (Korea, Republic of)

1997-12-31

Pyrolysis may be an important pretreatment step before vitrification in a cold crucible melter (CCM). During vitrification of organic resin the carbon or other remaining residues may harm the performance of the cold crucible melter of the eventual stability of the final glass product. Hence, it is important to reduce or prevent such harmful waste from entry into the cold crucible melter. Pretreatment with pyrolysis will generally provide volume reduction resulting in less amount of solid waste that needs to be handled by the CCM; in addition, the pyrolytic processes may breakdown much of the complex organics causing release through volatilization resulting in less carbon and other harmful substances. Hence, KEPRI has undertaken studies on the pyrolysis and oxidative pyrolysis of organic ion exchange resin. Pyrolysis and oxidative pyrolysis were examined with TGA and a tube furnace. TGA results for pyrolysis with the flow of nitrogen indicate that even after pyrolyzing from room temperature to about 900 deg C, a significant mass fraction of the original cationic resin remains, approximately 46 %. The anionic resin when pyrolytically heated in a flow of nitrogen only, from room temperature to about 900 deg C, produced a final residue mass fraction of about 8 percent. Oxidation at a ratio of air to nitrogen, 1:2, reduced the cationic resin to 5.3% when heated at 5 C/min. Oxidation of anionic resin at the same ratio and same heating rate left almost no solid residue. Pyrolysis (e.g. nitrogen-only environment) in the tube furnace of larger samples relative to the TGA produced very similar results to the TGA. The differences may be attributed to the scale effects such as surface area exposure to the gas stream, temperature distributions throughout the resin, etc. (author) 7 refs., 7 figs.

Marginal adaptation of composite resins under two adhesive techniques.

Science.gov (United States)

Dačić, Stefan; Veselinović, Aleksandar M; Mitić, Aleksandar; Nikolić, Marija; Cenić, Milica; Dačić-Simonović, Dragica

2016-11-01

In the present research, different adhesive techniques were used to set up fillings with composite resins. After the application of etch and rinse or self etch adhesive technique, marginal adaptation of composite fillings was estimated by the length of margins without gaps, and by the microretention of resin in enamel and dentin. The study material consisted of 40 extracted teeth. Twenty Class V cavities were treated with 35% phosphorous acid and restored after rinsing by Adper Single Bond 2 and Filtek Ultimate-ASB/FU 3M ESPE composite system. The remaining 20 cavities were restored by Adper Easy One-AEO/FU 3M ESPE composite system. Marginal adaptation of composite fillings was examined using a scanning electron microscope (SEM). The etch and rinse adhesive technique showed a significantly higher percentage of margin length without gaps (in enamel: 92.5%, in dentin: 57.3%), compared with the self-etch technique with lower percentage of margin length without gaps, in enamel 70.4% (p resin tugs in interprismatic spaces of enamel, while the dentin microretention was composed of adhesive and hybrid layers with resin tugs in dentin canals. In the second technique, resin tugs were rarely seen and a microgap was dominant along the border of restoration margins. The SEM analysis showed a better marginal adaptation of composite resin to enamel and dentin with better microretention when the etch and rinse adhesive procedure was applied. © 2016 Wiley Periodicals, Inc.

Photo-polymerization of photocurable resins containing polyhedral oligomeric silsesquioxane methacrylate

International Nuclear Information System (INIS)

Lin, Ho-May; Wu, Shi-Yin; Chang, Feng-Chih; Yen, Ying-Chieh

2011-01-01

Photocurable resins, bisphenol A propoxylate glycerolate diacrylate (BPA-PGDA, containing two hydroxyl) and bisphenol A propoxylate diacrylate (BPA-PDA), with fixed photoinitiator (Irgacure 907) concentration and various contents of methacrylisobutyl polyhedral oligomeric silsesquioxane (MI-POSS) were prepared and characterized by FTIR spectroscopy, scanning electron microscope and differential photocalorimetry. The MI-POSS molecules form crystals or aggregated particles in the cured resin matrix. The BPA-PGDA series photocurable resins show higher viscosity and lower photo-polymerization reactivity than the BPA-PDA series resins. The photo-polymerization rate and conversion of BPA-PGDA series are improved with increasing MI-POSS content. On the contrary, the photo-polymerization behavior of BPA-PDA series photocurable resins remains nearly unchanged by the addition of MI-POSS. Hydrogen-bonding interaction between the hydroxyl of BPA-PGDA and the siloxane of MI-POSS tends to attract and concentrate these acrylate double bonds around MI-POSS particles and thus enhances the photo-polymerization rate and conversion.

Manufacturing of a REBCO racetrack coil using thermoplastic resin aiming at Maglev application

International Nuclear Information System (INIS)

Mizuno, Katsutoshi; Ogata, Masafumi; Hasegawa, Hitoshi

2015-01-01

Highlights: • We propose a novel REBCO coil structure which applies thermoplastic resin. • The thermoplastic resin bonds the coil winding and cooling plates. • The adhesiveness of the resin is strong enough to withstand the thermal stress. • The thermoplastic resin does not cause the degradation because of its high viscosity. • We successfully made a full-scale racetrack REBCO coil with the thermoplastic resin. - Abstract: The REBCO coated conductor is a promising technology for the Maglev application in terms of its high critical temperature. The operating temperature of the on-board magnets can be around 40–50 K with the coated conductor. The REBCO coils are cooled by cryocoolers directly, and hence the thermal design of the REBCO coils significantly changes from that of LTS coils. We have developed a novel REBCO coil structure using thermoplastic resin. The coil is not impregnated and the thermoplastic resin is used to bond the coil winding and the heat transfer members, e.g. copper and aluminum plates. The viscosity of the thermoplastic resin is high enough for the thermoplastic resin not to permeate between the turns in the coil. Therefore, the thermal stress does not occur and the risk of degradation is removed. This paper contains the following three topics. First, the thermal resistance of the thermoplastic resin was measured at cryogenic temperature. Then, a small round REBCO coil was experimentally produced. It has been confirmed that the thermoplastic resin does not cause the degradation and, the adhesion between the coil winding and copper plates withstands the thermal stress. Finally, we successfully produced a full-scale racetrack REBCO coil applying the coil structure with the thermoplastic resin.