Effect of pore structure on the removal of clofibric acid by magnetic anion exchange resin.

Science.gov (United States)

Tan, Liang; Shuang, Chendong; Wang, Yunshu; Wang, Jun; Su, Yihong; Li, Aimin

2018-01-01

The effect of pore structure of resin on clofibric acid (CA) adsorption behavior was investigated by using magnetic anion exchange resins (ND-1, ND-2, ND-3) with increasing pore diameter by 11.68, 15.37, 24.94 nm. Resin with larger pores showed faster adsorption rates and a higher adsorption capacity because the more opened tunnels provided by larger pores benefit the CA diffusion into the resin matrix. The ion exchange by the electrostatic interactions between Cl-type resin and CA resulted in chloride releasing to the solution, and the ratio of released chloride to CA adsorption amount decreased from 0.90 to 0.65 for ND-1, ND-2 and ND-3, indicating that non-electrostatic interactions obtain a larger proportional part of the adsorption into the pores. Co-existing inorganic anions and organic acids reduced the CA adsorption amounts by the competition effect of electrostatic interaction, whereas resins with more opened pore structures weakened the negative influence on CA adsorption because of the existence of non-electrostatic interactions. 85.2% and 65.1% adsorption amounts decrease are calculated for resin ND-1 and ND-3 by the negative influence of 1 mmol L -1 NaCl. This weaken effect of organic acid is generally depends on its hydrophobicity (Log Kow) for carboxylic acid and its ionization degree (pKb) for sulfonic acid. The resins could be reused with the slightly decreases by 1.9%, 3.2% and 5.4% after 7 cycles of regeneration, respectively for ND-1, ND-2 and ND-3, suggesting the ion exchange resin with larger pores are against its reuse by the brine solution regeneration. Copyright © 2017 Elsevier Ltd. All rights reserved.

HTGR fuel development: loading of uranium on carboxylic acid cation-exchange resins using solvent extraction of nitrate

International Nuclear Information System (INIS)

Haas, P.A.

1975-09-01

The reference fuel kernel for recycle of 233 U to HTGR's (High-Temperature Gas-Cooled Reactors) is prepared by loading carboxylic acid cation-exchange resins with uranium and carbonizing at controlled conditions. The purified 233 UO 2 (NO 3 ) 2 solution from a fuel reprocessing plant contains excess HNO 3 (NO 3 - /U ratio of approximately 2.2). The reference flowsheet for a 233 U recycle fuel facility at Oak Ridge uses solvent extraction of nitrate by a 0.3 M secondary amine in a hydrocarbon diluent to prepare acid-deficient uranyl nitrate. This nitrate extraction, along with resin loading and amine regeneration steps, was demonstrated in 14 runs. No significant operating difficulties were encountered. The process is controlled via in-line pH measurements for the acid-deficient uranyl nitrate solutions. Information was developed on pH values for uranyl nitrate solution vs NO 3 - /U mole ratios, resin loading kinetics, resin drying requirements, and other resin loading process parameters. Calculations made to estimate the capacities of equipment that is geometrically safe with respect to control of nuclear criticality indicate 100 kg/day or more of uranium for single nitrate extraction lines with one continuous resin loading contactor or four batch loading contactors. (auth)

Processing of indium (III solutions via ion exchange with Lewatit K-2621 resin

Directory of Open Access Journals (Sweden)

López Díaz-Pavón, Adrián

2014-06-01

Full Text Available The processing of indium(III-hydrochloric acid solutions by the cationic ion exchange Lewatit K-2621 resin has been investigated. The influence of several variables such as the hydrochloric acid and metal concentrations in the aqueous solution and the variation of the amount of resin added has been studied. Moreover, a kinetic study performed in the uptake of indium(III by Lewatit K-2621, shows that either the film-diffusion and the particle-diffusion models fit the ion exchange process onto the resin, depending upon the initial metal concentration in the aqueous solution. The loaded resin could be eluted by HCl solutions at 20 °C.Se ha investigado el tratamiento de disoluciones de ácido clorhídrico conteniendo indio(III mediante la resina de cambio catiónico Lewatit K-2621. Las variables ensayadas han sido las concentraciones de ácido y de metal en la disolución acuosa y la cantidad de resina empleada en el tratamiento de dichas disoluciones. Asimismo, se ha llevado a cabo un estudio cinético del proceso de intercambio catiónico entre el indio(III y la resina Lewatit K-2621. Este estudio muestra que el proceso de intercambio responde a un mecanismo de difusión en la disolución o en la partícula de resina dependiendo de la concentración inicial del metal en el medio acuoso. El metal cargado en la resina puede ser eluido con disoluciones de ácido clorhídrico a 20 °C.

Ion-exclusion chromatography with conductimetric detection of aliphatic carboxylic acids on a weakly acidic cation-exchange resin by elution with benzoic acid-beta-cyclodextrin.

Science.gov (United States)

Tanaka, Kazuhiko; Mori, Masanobu; Xu, Qun; Helaleh, Murad I H; Ikedo, Mikaru; Taoda, Hiroshi; Hu, Wenzhi; Hasebe, Kiyoshi; Fritz, James S; Haddad, Paul R

2003-05-16

In this study, an aqueous solution consisting of benzoic acid with low background conductivity and beta-cyclodextrin (beta-CD) of hydrophilic nature and the inclusion effect to benzoic acid were used as eluent for the ion-exclusion chromatographic separation of aliphatic carboxylic acids with different pKa values and hydrophobicity on a polymethacrylate-based weakly acidic cation-exchange resin in the H+ form. With increasing concentration of beta-cyclodextrin in the eluent, the retention times of the carboxylic acids decreased due to the increased hydrophilicity of the polymethacrylate-based cation-exchange resin surface from the adsorption of OH groups of beta-cyclodextrin. Moreover, the eluent background conductivity decreased with increasing concentration of beta-cyclodextrin in 1 mM benzoic acid, which could result in higher sensitivity for conductimetric detection. The ion-exclusion chromatographic separation of carboxylic acids with high resolution and sensitivity was accomplished successfully by elution with a 1 mM benzoic acid-10 mM cyclodextrin solution without chemical suppression.

Study of plutonium IV elution from macromolecular anion exchange resin by 0.5 M nitric acid

International Nuclear Information System (INIS)

Nadkarni, M.N.; Mayankutty, P.C.; Pillai, N.S.; Shinde, S.S.

1976-01-01

Preliminary studies indicated that macroreticular resins possess more or less the same capacities and absorption characteristics for thorium, uranium and plutonium from nitric acid solutions as the conventional resins. Detailed studies were, then, conducted. It was found that Pu(IV) can be loaded on the macroreticular anion exchange resin, Amberlyst A-26 from 7.2 M nitric acid in much the same way as Dowex 1x4. It was also observed that the elution of Pu(IV) from Amberlyst A-26 by 0.5 M nitric acid is much more rapid and quantitative than from Dowex 1x4. (author)

Input to Resin Column Structural Analysis if Autocatalytic Resin Reaction Occurs in HB-Line Phase II

Energy Technology Data Exchange (ETDEWEB)

Hallman, D.F.

2001-07-10

Solutions of plutonium in nitric acid are purified and concentrated using anion resin prior to precipitation. There have been instances of resin column explosions caused by autocatalytic reactions of anion resins in nitric acid within the DOE complex

Modification of Aliphatic Petroleum Resin by Peracetic Acid

OpenAIRE

Bondaletov, Vladimir Grigoryevich; Bondaletova, Lyudmila Ivanovna; Hamlenko, A.; Bondaletov, Oleg Vladimirovich; Starovoit, M.

2014-01-01

This work demonstrates the possibility of obtaining modified aliphatic resin (PRC5) by means of petroleum resin oxidation by peracetic acid. We have experimentally determined oxidation conditions that lead to producing resin with maximum epoxy and acid numbers. Ratio of "oxidative system: PRC5" is 0.5:1, process duration is 2 hours. The modified resin structure is determined by IR and NMR spectroscopy.

Adsorption behaviors of trivalent actinides and lanthanides on pyridine resin in lithium chloride aqueous solution

International Nuclear Information System (INIS)

Tatsuya Suzuki

2013-01-01

The adsorption behaviors of trivalent actinides and lanthanides on pyridine resin in lithium chloride aqueous solution were investigated. The adsorbed amounts of lanthanides and the degree of mutual separation of lanthanides increased with an increase in the concentration of lithium chloride in aqueous solution. The group separation of the trivalent actinides and lanthanides was observed. This separation phenomenon is similar in a hydrochloric acid solution. However, the adsorption behavior of lanthanides in lithium chloride is different from their behavior in a hydrochloric acid solution. This fact shows that the adsorption mechanisms of lanthanides in a lithium chloride aqueous solution and in a hydrochloric acid solution are different; the adsorption mechanisms are attributed to the ion exchange in a hydrochloric acid solution, and to the complex formation with pyridine group in a lithium chloride solution. (author)

Extraction behaviour of Am(III) and Eu(III) from nitric acid medium in TEHDGA-HDEHP impregnated resins

Energy Technology Data Exchange (ETDEWEB)

Saipriya, G.; Kumar, T. [Bhabha Atomic Research Centre Facilities, Kalpakkam (India). Kalpakkam Reprocessing Plant; Kumaresan, R.; Nayak, P.K.; Venkatesan, K.A.; Antony, M.P. [Indira Gandhi Center for Atomic Research, Kalpakkam (India). Fuel Chemistry Div.

2016-07-01

The extraction behaviour of Am(III) and Eu(III) from nitric acid medium was studied in the solvent impregnated resins containing extractants such as tetra-bis(2-ethylhexyl)diglycolamide (TEHDGA) or bis-(2-ethylhexyl)phosphoric acid (HDEHP) or mixture of TEHDGA+HDEHP. The rate of extraction of Am(III) and Eu(III) from 1 M nitric acid and the effect of various parameters, such as the concentration of nitric acid in aqueous phase and concentration of TEHDGA and HDEHP in resin phase, on the distribution coefficient of Am(III) and Eu(III) was studied. The distribution coefficient of Am(III) and Eu(III) in HDEHP-impregnated resin decreased and that in TEHDGA-impregnated resin increased, with increase in the concentration of nitric acid. However, in (TEHDGA+HDEHP) - impregnated resin, synergic extraction was observed at lower nitric acid concentration and antagonism at higher nitric acid concentration. The mechanism of Am(III) and Eu(III) extraction in the combined resin was investigated by slope analysis method. The extraction of various metal ions present in the fast reactor simulated high-level liquid waste was studied. The separation factor of Am(III) over Eu(III) was studied using citrate-buffered diethylenetriaminepentaacetic acid (DTPA) solution.

Synthesis of a chelate resin with amido and phosphoric acid and its character in uranium extraction

International Nuclear Information System (INIS)

Qiu Yueshuang; Zhang Jianguo; Feng Yu; Zhao Chaoya

2013-01-01

A chelate resin (D814) with amido and phosphoric acid functional group was synthetized by means of the reactions of stytene-divinyl benzene chloromethylated sphere with ethylenedianmine and orth-phosphorous acid and formaldehyde. This resin can be used to adsorb uranium from leaching solution with high chloride ion in the rang of pH l.33-9.05, and the adsorption rate of uranium was above 95%. D814 resin had a good ability resistant to high chloride ion. The loading capacity for uranium was not apparently effected when chlorid ion concentration in solution was 60 g/L. The results of the adsorption experiment show that when the ratio of saturation volume to breakthrough volume was l.82, the uranium saturation capacity of D814 was 40.5 mg/g dry resin. NaCl + NaHCO 3 was used for eluting agent, and the eluting rate of uranium was 96.7%. Adsorption uranium mechanism by D814 was also discussed. (authors)

Correlation and prediction of ion exchange equilibria on weak-acid resins by means of the surface complex formation model

International Nuclear Information System (INIS)

Horst, J.

1988-11-01

The present work summarizes investigations of the equilibrium of the exchange of protons, copper, zinc, calcium, magnesium and sodium ions on two weak-acid exchange resins in hydrochloric and carbonic acid bearing solutions at 25 0 C. The description of the state of equilibrium between resin and solution is based on the individual chemical equilibria which have to be adjusted simultaneously. The equilibrium in the liquid phase is described by the mass action law and the condition of electroneutrality using activity coefficients calculated according to the theory of Debye and Hueckel. The exchange equilibria are described by means of a surface complex formation model, which was developed by Davis, James and Leckie for activated aluminia and which has been applied to weak-acid resins. The model concept assumes the resin as a plane surface in which the functional groups are distributed uniformly. (orig./RB) [de

The effect of loading solution and dissolution media on release of Diclofenac from ion exchange resins

Directory of Open Access Journals (Sweden)

"Atyabi F

2002-07-01

Full Text Available Drugs can be loaded on ion exchange resins in order to control their release. Loading of diclofenac sodium on the resin beads not only sustain its release but also reduce its gastrointestinal mucosal injury. In this study the effect of loading solution and concentration of diclofenac in loading solution on total amount of drug loaded on the resin beads (Amberlite IRA-900 and the release characteristic of drug in different media were examined. Results showed that diclofenac resin complex did not release their drug content in simulated gastric fluid but released it in simulated intestinal fluid independent of exposure time in acidic conditions. The effect of a number of parameters such as ionic strength and pH on the release characteristic of drug - resin complexes were also examined. Results showed that although ionic strength is an important factor, drug release is more affected by the pH of the media. NO ABSTRACT

Affinity resins as new tools for identifying target proteins of ascorbic acid.

Science.gov (United States)

Iwaoka, Yuji; Nishino, Kohei; Ishikawa, Takahiro; Ito, Hideyuki; Sawa, Yoshihiro; Tai, Akihiro

2018-02-12

l-Ascorbic acid (AA) has diverse physiological functions, but little is known about the functional mechanisms of AA. In this study, we synthesized two types of affinity resin on which AA is immobilized in a stable form to identify new AA-targeted proteins, which can provide important clues for elucidating unknown functional mechanisms of AA. To our knowledge, an affinity resin on which AA as a ligand is immobilized has not been prepared, because AA is very unstable and rapidly degraded in an aqueous solution. By using the affinity resins, cytochrome c (cyt c) was identified as an AA-targeted protein, and we showed that oxidized cyt c exhibits specific affinity for AA. These results suggest that two kinds of AA-affinity resin can be powerful tools to identify new target proteins of AA.

Treatment method for stabilization of radioactive exchange resin

International Nuclear Information System (INIS)

Hideo, Oni; Takashi, Miyake; Hitoshi, Miyamoto; Toshio, Funakoshi; Yuzo, Inagaki.

1988-01-01

This is a method for eluting radioactive nuclides from a radioactive ion exchange resin in which it has been absorbed. First, the Cs in this resin is extracted using a neutral salt solution which contains Na + . The Cs that has been transferred to the neutral salt solution is absorbed and expelled by inorganic ion exchangers. Then the Co, Fe, Mn and Sr in said resin are eluted using an acidic solution; the Co, Fe, Mn and Sr that have been transferred to the acidic solution are separated from that solution by means of a diffusion dialysis vat. This process is a unique characteristic of this ion exchange resin treatment method. 1 fig

The combined effect of food-simulating solutions, brushing and staining on color stability of composite resins

Science.gov (United States)

Silva, Tânia Mara Da; Sales, Ana Luísa Leme Simões; Pucci, Cesar Rogerio; Borges, Alessandra Bühler; Torres, Carlos Rocha Gomes

2017-01-01

Abstract Objective: This study evaluated the effect of food-simulating media associated with brushing and coffee staining on color stability of different composite resins. Materials and methods: Eighty specimens were prepared for each composite: Grandio SO (Voco), Amaris (Voco), Filtek Z350XT (3M/ESPE), Filtek P90 (3M/ESPE). They were divided into four groups according to food-simulating media for 7 days: artificial saliva (control), heptane, citric acid and ethanol. The composite surface was submitted to 10,950 brushing cycles (200 g load) in an automatic toothbrushing machine. The specimens were darkened with coffee solution at 37 °C for 24 h. After each treatment, color measurements were assessed by spectrophotometry, using CIE L*a*b* system. The overall color change (ΔE) was determined for each specimen at baseline (C1) and after the treatments (food-simulating media immersion/C2, brushing/C3 and dye solution/C4). Data were analyzed by two-way repeated measures ANOVA and Tukey’s tests (p composites (p = .001), time (p = .001) and chemical degradation (p = .002). The mean of ΔE for composites were: Z350XT (5.39)a, Amaris (3.89)b, Grandio (3.75)bc, P90 (3.36)c. According to food-simulating media: heptane (4.41)a, citric acid (4.24)a, ethanol (4.02)ab, artificial saliva (3.76)b. For the treatments: dye solution (4.53)a, brushing (4.26)a, after food-simulating media (3.52)b. Conclusions: The composite resin Filtek Z350XT showed significantly higher staining than all other composite resin tested. The immersion in heptane and citric acid produced the highest color alteration than other food-simulating media. The exposure of samples to brushing protocols and darkening in coffee solution resulted in significant color alteration of the composite resins. PMID:28642926

Kinetic study of ion exchange in phosphoric acid chelating resin

International Nuclear Information System (INIS)

Brikci-Nigassa, Mounir; Hamouche, Hafida

1995-11-01

Uranium may be recovered as a by product of wet phosphoric acid using a method based on specific ion exchange resins. These resins called chelates contain amino-phosphonic functional groups. The resin studied in this work is a purolite S-940; uranium may be loaded on this resin from 30% P2O5 phosphoric acid in its reduced state. The influence of different parameters on the successive steps of the process have been studied in batch experiments: uranium reduction, loading and oxydation. Uranium may be eluted with ammonium carbonate and the resin regeneration may be done with hydrochloric acid.Ferric ions reduce the effective resin capacity considerably and inert fixation conditions are proposed to enhance uranium loading

Synthesis, characterization and applications of a new cation exchanger tamarind sulphonic acid (TSA) resin.

Science.gov (United States)

Singh, A V; Sharma, Naresh Kumar; Rathore, Abhay S

2012-01-01

A new composite cation exchanger, tamarind sulphonic acid (TSA) resin has been synthesized. The chemically modified TSA ion exchange resin has been used for the removal and preconcentration of Zn2+, Cd2+, Fe2+, Co2+ and Cu2+ ions in aqueous solution and effluent from the Laxmi steel plant in Jodhpur, India. This type of composite represents a new class of hybrid ion exchangers with good ion exchange capacity, stability, reproducibility and selectivity for toxic metal ions found in effluent from the steel industry. The characterization of the resin was carried out by determining the ion-exchange capacity, elemental analysis, pH titration, Fourier transform infrared spectra and thermal analysis. The distribution coefficients (K(d)) of toxic metal ions were determined in a reference aqueous solution and the steel plant effluent at different pH values; the absorbency of different metal ions on the TSA resin was studied for up to 10 cycles. The adsorption of different metal ions on TSA resin follows the order: Co2+ > Cu2+ > Zn2+ > Fe2+ > Cd2+. The ion exchange capacity of TSA resin is 2.87%.

Behaviour of Pu-IV with various ion exchangers in solutions containing nitric acid and oxalates

International Nuclear Information System (INIS)

Walter, E.; Ali, S.A.

1982-02-01

The distribution of Pu-IV on the ion exchangers Dowex 50W-X8, Dowex 1-X8 und Dowex Chelating Resin Al-X8 in the presence of various concentrations of nitric acid and oxalate were investigated. The results indicate that nitric acid and oxalic acid influence each other during complexation of Pu-IV with oxalate ions solutions containing nitric acid it is not possible to neglect the formation of Pu-IV nitrate complexes. The complex Pu(IV) (C 2 O 4 ) 3 2 - only is formed in solutions containing low nitric acid and high oxalic acid concentrations. The separation of Pu-IV in Dowex Chelating Resin from nitric acid solution in the presence of higher oxalate concentrations is possible, provided that the nitric acid concentration is lower than 0.25 molar [fr

Development of production methods of volume source by the resinous solution which has hardening

CERN Document Server

Motoki, R

2002-01-01

Volume sources is used for standard sources by radioactive measurement using Ge semiconductor detector of environmental sample, e.g. water, soil and etc. that require large volume. The commercial volume source used in measurement of the water sample is made of agar-agar, and that used in measurement of the soil sample is made of alumina powder. When the plastic receptacles of this two kinds of volume sources were damaged, the leakage contents cause contamination. Moreover, if hermetically sealing performance of volume source made of agar-agar fell, volume decrease due to an evaporation off moisture gives an error to radioactive measurement. Therefore, we developed the two type methods using unsaturated polyester resin, vinilester resin, their hardening agent and acrylicresin. The first type is due to dispersing the hydrochloric acid solution included the radioisotopes uniformly in each resin and hardening the resin. The second is due to dispersing the alumina powder absorbed the radioisotopes in each resin an...

Study of free acidity determinations in aqueous solution

International Nuclear Information System (INIS)

Kergreis, A.

1966-04-01

The object of this work is the study of the principal methods which can be applied to the measurement of 'free' acidity. In the first part, we define the various types of acidity which can exist in aqueous solution; then, after having studied some hydrolysis reactions, we compare the value of the neutralisation pH of the hydrated cation and that of the precipitation of the hydroxide. In the second part we have started to study the determination of the acidity of an aqueous solution. After having rapidly considered the 'total' acidity determination, we deal with the problem of the 'free' acidity titration. We have considered in particular certain methods: extrapolation of the equivalent point, colorimetric titrations with or without a complexing agent, and finally the use of ion-exchange resins with mixed aqueous and solvent solutions. (author) [fr

Enhanced vanillin production from ferulic acid using adsorbent resin.

Science.gov (United States)

Hua, Dongliang; Ma, Cuiqing; Song, Lifu; Lin, Shan; Zhang, Zhaobin; Deng, Zixin; Xu, Ping

2007-03-01

High vanillin productivity was achieved in the batch biotransformation of ferulic acid by Streptomyces sp. strain V-1. Due to the toxicity of vanillin and the product inhibition, fed-batch biotransformation with high concentration of ferulic acid was unsuccessful. To solve this problem and improve the vanillin yield, a biotransformation strategy using adsorbent resin was investigated. Several macroporous adsorbent resins were chosen to adsorb vanillin in situ during the bioconversion. Resin DM11 was found to be the best, which adsorbed the most vanillin and the least ferulic acid. When 8% resin DM11 (wet w/v) was added to the biotransformation system, 45 g l(-1) ferulic acid could be added continually and 19.2 g l(-1) vanillin was obtained within 55 h, which was the highest vanillin yield by bioconversion until now. This yield was remarkable for exceeding the crystallization concentration of vanillin and therefore had far-reaching consequence in its downstream processing.

Removing and recovering of uranium from the acid mine waters by using ion exchange resin

International Nuclear Information System (INIS)

Nascimento, Marcos Roberto Lopes do

1998-01-01

Ion exchange using resins is one of the few processes capable of reducing ionic contaminants in effluents to very low levels. In this study the process was used to remove and recovery uranium from acid mine waters at Pocos de Caldas-MG Uranium Mining and Milling Plant. The local mineralogical features, allied to the biogeochemical phenomena, owing to presence of pyrite in the rock piles, moreover another factors, resulting acid drainage with several pollutants, including uranium ranging from 6 to 14 mg/l, as sulfate complex, that can be removed by anionic exchanger. The iron interference is eliminated by lime pretreatment of water, increasing pH from 2.6 to 3.3-3.8 to precipitate this cation, without changing the uranium amount. Eight anionic resins were tested, based on the uranium loading, in sorption studies. Retention time, and pH influence was verified for the exchanger chose. With breakthrough of 1 mg U/L and 10 mg U/l in the feed solution, the uranium decontamination level was 94%. Typical values of loading resin were 20-30 g U/l and 70-90 g SO 4 /l. Uranium elution was done with Na Cl solution. Retention time, saline, and acid concentration were the parameters studied. The concentrate, obtained from the eluate by ammonia precipitation, presented uranium (86,8% as U 3 O 8 ) and impurities within commercial specifications. (author)

Process for removing a mixture containing iodine and alkyl iodine compounds from a gas phase or aqueous solution with ion-exchange resins

Energy Technology Data Exchange (ETDEWEB)

Shimizu, H; Mizuuchi, A; Yokoyama, F

1968-10-04

Iodine and alkyl iodine compounds are removed from a gas phase or aqueous solution containing salts, iodine and iodine compounds, such as the ambient gas in a reactor, if an accident should occur. The process comprises contacting the phase or solution: (a) with a hydrogen type strongly acidic cationic exchange resin, (b) with an anionic exchange resin containing quarternary ammonium and (c) with an anionic exchange resin containing free basic type tertiary amine, in this order or by reversing the order of the two anionic exchange resins. Although no problems arise in the liquid phase reaction, the ion-exchange resins in the gas phase reaction are desired in the moist state in order to stable maintain the migration speed of the materials to be removed regardless of the relative humidity of the amibent gas. In example I, Amberlite IRA-900 of 200 mm thickness as the lowermost bed, Amberlite IRA93 of 200 mm thickness as the middle bed and Amberlite 200 of 200 mm thickness as the uppermost bed were filled respectively, in a methacrylate resin cylinder with an inner diameter of 25 mm. A solution containing 15.9 mg/1 of iodine, 41.2 mg/1 of methyl iodide and 550 mg/1 of sodium carbonate flows at a rate of 15 liter/hr downward through the beds. As a result of testing, no iodine, iodine ions, iodic acid ions and methyl iodine were detected. The amount of water the beds could treat was 60 times the total quantity of the filled resins.

Microbial activity in an acid resin deposit: Biodegradation potential and ecotoxicology in an extremely acidic hydrocarbon contamination

International Nuclear Information System (INIS)

Kloos, Karin; Schloter, Michael; Meyer, Ortwin

2006-01-01

Acid resins are residues produced in a recycling process for used oils that was in use in the forties and fifties of the last century. The resin-like material is highly contaminated with mineral oil hydrocarbons, extremely acidic and co-contaminated with substituted and aromatic hydrocarbons, and heavy metals. To determine the potential for microbial biodegradation the acid resin deposit and its surroundings were screened for microbial activity by soil respiration measurements. No microbial activity was found in the core deposit. However, biodegradation of hydrocarbons was possible in zones with a lower degree of contamination surrounding the deposit. An extreme acidophilic microbial community was detected close to the core deposit. With a simple ecotoxicological approach it could be shown that the pure acid resin that formed the major part of the core deposit, was toxic to the indigenous microflora due to its extremely low pH of 0-1. - Acidity is the major toxic factor of the extremely hydrophobic and acidic mixed contamination found in an acid resin deposit

Ion exchange resin fouling of molybdenum in recovery uranium processess

International Nuclear Information System (INIS)

Zhang Guowei; Zhao Guirong

1990-09-01

The relationship between anion exchange resin fouling and molybdic acid polymerization was studied. By using potentiometer titration and laser-Raman spectroscopy the relationship of molybdic acid polymerization and the pH value of solution or the molybdenum concentration was determined. It was shown that as the concentration of initial molybdenum in solution decreases from 0.2 mol/L to 0.5 mmol/L, the pH value of starting polymerization decreased from 6.5 to 4.5. The experimental results show that the fouling of 201 x 7 resin in the acidic solution is mainly caused by the adsorbing of Mo 3 O 26 4- ion and occupying the exchange radical site of the resin. Under the leaching conditions the molybdenum and phosphate existing in the leaching liquor can form 12-molybdo-phosphate ion. It also leads to resin fouling. The molybdenum on the fouled resin can synergically be desorbed by mixed desorbents containing ammonium hydroxide and ammonium sulfate. The desorbed resin can be used for uranium adsorption and the desorbed molybdenum can be recovered by ion exchange method

Reactivity of Resorcinol Formaldehyde Resin with Nitric Acid

International Nuclear Information System (INIS)

King, William D.; Fondeur, Fernando F.; Wilmarth, William R.; Pettis, Myra E.

2005-01-01

Solid-state infrared spectroscopy, differential scanning calorimetry, and elemental analysis have been used to evaluate the reactivity of resorcinol formaldehyde resin with nitric acid and characterize the solid product. Two distinct reactions were identified within the temperature range 25-55 C. The first reaction is primarily associated with resin nitration, while the second involves bulk oxidation and degradation of the polymer network leading to dissolution and off-gassing. The threshold conditions promoting reaction have been identified. Reaction was confirmed with nitric acid concentrations as low as 3 M at 25 C applied temperature and 0.625 M at 66 C. Although a nitrated resin product can be isolated under appropriate experimental conditions, calorimetry testing indicates no significant hazard associated with handling the dry material

Anion-exchange Studies of Radioactive Trace Elements in Sulphuric Acid Solutions

Energy Technology Data Exchange (ETDEWEB)

Samsahl, K

1963-01-15

As part of a chemical group separation procedure used as a pretreatment in gamma spectrometric analysis, a study has been made of the adsorption from sulphuric acid solutions on strongly basic anion exchange resins, prepared in the hydroxide and the sulphate forms, of trace activities of Na, P, K, Ca, Sc, Cr, Mn, Fe, Co, Ni, Cu, Zn, Ga, Rb, Sr, Zr, Nb, Mo, Tc, Ag, Cd, In, Cs, Ba, La, Ce, Hf, Ta, W, Ir, Pa and Np. Besides adsorbing some of the trace elements in the solution, the anion exchange resin in the hydroxide form will neutralize the bulk of the sulphuric acid. This makes possible the subsequent sequential separation of chloride complexes on short anion-exchange columns by a stepwise increasing of the HCl concentration of the solution. On the basis of the results obtained in the present and earlier experiments, a new improved chemical group-separation procedure for mixtures of radioactive trace elements is outlined.

The transverse strength of acrylic resin after Coleus amboinicus, Lour extract solution immersion

OpenAIRE

Rianti, Devi

2006-01-01

A laboratoric experimental study was conducted on the transverse strength of acrylic resin after Coleus amboinicus, Lour extract solution immersion. The aim of this study is to know the difference of acrylic resin transverse strengths caused by immersion time variations in a concentrate solution. The study was carried out on unpolished acrylic resin plates with 65 × 10 × 2,5 mm dimension; solution with 15% Coleus amboinicus, Lour extract, and 30, 60, 90 days immersion times to measure the tra...

Recovery of lactic acid from the pretreated fermentation broth based on a novel hyper-cross-linked meso-micropore resin: Modeling.

Science.gov (United States)

Song, Mingkai; Jiao, Pengfei; Qin, Taotao; Jiang, Kangkang; Zhou, Jingwei; Zhuang, Wei; Chen, Yong; Liu, Dong; Zhu, Chenjie; Chen, Xiaochun; Ying, Hanjie; Wu, Jinglan

2017-10-01

An innovative benign process for recovery lactic acid from its fermentation broth is proposed using a novel hyper-cross-linked meso-micropore resin and water as eluent. This work focuses on modeling the competitive adsorption behaviors of glucose, lactic acid and acetic acid ternary mixture and explosion of the adsorption mechanism. The characterization results showed the resin had a large BET surface area and specific pore structure with hydrophobic properties. By analysis of the physicochemical properties of the solutes and the resin, the mechanism of the separation is proposed as hydrophobic effect and size-exclusion. Subsequently three chromatographic models were applied to predict the competitive breakthrough curves of the ternary mixture under different operating conditions. The pore diffusion was the major limiting factor for the adsorption process, which was consistent with the BET results. The novel HD-06 resin can be a good potential adsorbent for the future SMB continuous separation process. Copyright © 2017 Elsevier Ltd. All rights reserved.

Screening Analyses of Pinosylvin Stilbenes, Resin Acids and Lignans in Norwegian Conifers

OpenAIRE

Anne Fiksdahl; Karin Oyaas; Ingebjorg Leirset; Hanne Hovelstad

2006-01-01

The content and distribution of stilbenes and resin acids in Scots pine (Pinus sylvestris) and spruce (Picea abies), sampled in central Norway, have been examined. The contents of pinosylvin stilbenes in pine heartwood/living knots were 0.2-2/2-8 % (w/w). No stilbenes could be detected in spruce (Picea abies). The resin acid contents of pine sapwood/heartwood and knots were 1-4 and 5-10 % (w/w), respectively. Minor amounts of resin acids (

Fabrication of micro-dot arrays and micro-walls of acrylic acid/melamine resin on aluminum by AFM probe processing and electrophoretic coating

International Nuclear Information System (INIS)

Kurokawa, S.; Kikuchi, T.; Sakairi, M.; Takahashi, H.

2008-01-01

Micro-dot arrays and micro-walls of acrylic acid/melamine resin were fabricated on aluminum by anodizing, atomic force microscope (AFM) probe processing, and electrophoretic deposition. Barrier type anodic oxide films of 15 nm thickness were formed on aluminum and then the specimen was scratched with an AFM probe in a solution containing acrylic acid/melamine resin nano-particles to remove the anodic oxide film locally. After scratching, the specimen was anodically polarized to deposit acrylic acid/melamine resin electrophoretically at the film-removed area. The resin deposited on the specimen was finally cured by heating. It was found that scratching with the AFM probe on open circuit leads to the contamination of the probe with resin, due to positive shifts in the potential during scratching. Scratching of the specimen under potentiostatic conditions at -1.0 V, however, resulted in successful resin deposition at the film-removed area without probe contamination. The rate of resin deposition increased as the specimen potential becomes more positive during electrophoretic deposition. Arrays of resin dots with a few to several tens μm diameter and 100-1000 nm height, and resin walls with 100-1000 nm height and 1 μm width were obtained on specimens by successive anodizing, probe processing, and electrophoretic deposition

Fabrication of micro-dot arrays and micro-walls of acrylic acid/melamine resin on aluminum by AFM probe processing and electrophoretic coating

Energy Technology Data Exchange (ETDEWEB)

Kurokawa, S.; Kikuchi, T.; Sakairi, M. [Graduate School of Engineering, Hokkaido University, N-13, W-8, Kita-Ku, Sapporo 060-8628 (Japan); Takahashi, H. [Graduate School of Engineering, Hokkaido University, N-13, W-8, Kita-Ku, Sapporo 060-8628 (Japan)], E-mail: takahasi@elechem1-mc.eng.hokudai.ac.jp

2008-11-30

Micro-dot arrays and micro-walls of acrylic acid/melamine resin were fabricated on aluminum by anodizing, atomic force microscope (AFM) probe processing, and electrophoretic deposition. Barrier type anodic oxide films of 15 nm thickness were formed on aluminum and then the specimen was scratched with an AFM probe in a solution containing acrylic acid/melamine resin nano-particles to remove the anodic oxide film locally. After scratching, the specimen was anodically polarized to deposit acrylic acid/melamine resin electrophoretically at the film-removed area. The resin deposited on the specimen was finally cured by heating. It was found that scratching with the AFM probe on open circuit leads to the contamination of the probe with resin, due to positive shifts in the potential during scratching. Scratching of the specimen under potentiostatic conditions at -1.0 V, however, resulted in successful resin deposition at the film-removed area without probe contamination. The rate of resin deposition increased as the specimen potential becomes more positive during electrophoretic deposition. Arrays of resin dots with a few to several tens {mu}m diameter and 100-1000 nm height, and resin walls with 100-1000 nm height and 1 {mu}m width were obtained on specimens by successive anodizing, probe processing, and electrophoretic deposition.

Study of free acidity determinations in aqueous solution; Etude des dosages d'acidite libre en solution aqueuse

Energy Technology Data Exchange (ETDEWEB)

Kergreis, A [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

1966-04-01

The object of this work is the study of the principal methods which can be applied to the measurement of 'free' acidity. In the first part, we define the various types of acidity which can exist in aqueous solution; then, after having studied some hydrolysis reactions, we compare the value of the neutralisation pH of the hydrated cation and that of the precipitation of the hydroxide. In the second part we have started to study the determination of the acidity of an aqueous solution. After having rapidly considered the 'total' acidity determination, we deal with the problem of the 'free' acidity titration. We have considered in particular certain methods: extrapolation of the equivalent point, colorimetric titrations with or without a complexing agent, and finally the use of ion-exchange resins with mixed aqueous and solvent solutions. (author) [French] Le but de ce travail est l'etude des principales methodes de determination de l'acidite 'libre'. Dans une premiere partie nous avons defini les differentes sortes d'acidites pouvant exister en solution aqueuse, puis apres avoir etudie quelques reactions d'hydrolyse, nous avons compare la valeur de pH de neutralisation du cation hydrate et celle de precipitation de l'hydroxyde. Dans la seconde partie nous avons aborde l'etuce des dosages de l'acidite d'une solution aqueuse. Apres avoir envisage assez rapidement la determination de l'acidite 'totale', nous traitons du probleme du titrage de l'acidite 'libre'. Nous avons porte notre attention sur certaines methodes: extrapolation du point equivalent, titrimetrie colorimetrique avec ou sans complexant, et enfin utilisation des resines echangeuses d'ions en milieu aqueux et solvant mixte.

The absorption of plutonium by anion resins

Energy Technology Data Exchange (ETDEWEB)

Durham, R. W.; Mills, R.

1961-10-15

Equilibrium experiments have shown Pu{sup +4} to be absorbed from nitric acid onto an anion resin as a complex anion Pu(NO{sub 3}){sub 6}{sup -2}. The amount of absorption is dependent on the plutonium and nitric acid concentrations in the equilibrium solution with a maximum at 7N to 8N HNO{sub 3}. A low cross-linked resin has a higher capacity and reaches equilibrium more rapidly than the normally supplied resin. Saturation capacity of one per cent cross-linked Nalcite SBR (Dowex 1), 50 -- 100 mesh, is 385 mg Pu/gram dry resin. (author)

Quantitative analysis of PMR-15 polyimide resin by HPLC

Science.gov (United States)

Roberts, Gary D.; Lauver, Richard W.

1987-01-01

The concentration of individual components and of total solids of 50 wt pct PMR-15 resin solutions was determined using reverse-phase HPLC to within + or - 8 percent accuracy. Acid impurities, the major source of impurities in 3,3', 4,4'-benzophenonetetracarboxylic acid (BTDE), were eliminated by recrystallizing the BTDE prior to esterification. Triester formation was not a problem because of the high rate of esterification of the anhydride relative to that of the carboxylic acid. Aging of PMR-15 resin solutions resulted in gradual formation of the mononadimide and bisnadimide of 4,4'-methylenedianiline, with the BTDE concentration remaining constant. Similar chemical reactions occurred at a reduced rate in dried films of PMR-15 resin.

The transverse strength of acrylic resin after Coleus amboinicus, Lour extract solution immersion

Directory of Open Access Journals (Sweden)

Devi Rianti

2006-12-01

Full Text Available A laboratoric experimental study was conducted on the transverse strength of acrylic resin after Coleus amboinicus, Lour extract solution immersion. The aim of this study is to know the difference of acrylic resin transverse strengths caused by immersion time variations in a concentrate solution. The study was carried out on unpolished acrylic resin plates with 65 × 10 × 2,5 mm dimension; solution with 15% Coleus amboinicus, Lour extract, and 30, 60, 90 days immersion times to measure the transverse strength and sterilized aquadest was used as control. Acrylic resin plates transverse strength was measured using Autograph AG-10 TE. The data was analyzed using One-Way Anova and LSD with 5% degree of significance. The result showed that longer immersion time will decrease the transverse strength of the acrylic resin plates. After 90 days immersion time, the transverse strength decrease is still above the recommended standard transverse strength.

An investigation of the applicability of the new ion exchange resin, Reillex{trademark}-HPQ, in ATW separations. Milestone 4, Final report

Energy Technology Data Exchange (ETDEWEB)

Ashley, K.R.; Ball, J.; Grissom, M.; Williamson, M.; Cobb, S.; Young, D.; Wu, Yen-Yuan J.

1993-09-07

The investigations with the anion exchange resin Reillex{trademark}-HPQ is continuing along several different paths. The topics of current investigations that are reported here are: The sorption behavior of chromium(VI) on Reillex{trademark}-HPQ from nitric acid solutions and from sodium hydroxide/sodium nitrate solutions; sorption behavior of F{sup {minus}} on Reillex{trademark}-HPQ resin in acidic sodium nitrate solution; sorption behavior of Cl{sup {minus}} on Reillex{trademark}-HPQ resin in acidic sodium nitrate solution; sorption behavior of Br{sup {minus}} on Reillex{trademark}-HPQ resin in acidic sodium nitrate solution; and the Honors thesis by one of the students is attached as Appendix II (on ion exchange properties of a new macroperous resin using bromide as the model ion in aqueous nitrate solutions).

A study of adsorption equilibrium on quaternary ammonium resin in uranyl sulphate solution

International Nuclear Information System (INIS)

Xu Genfu; Xu Jiazhong; Zhu Jinghua

1986-01-01

Adsorption equilibrium on quaternary ammonium resin in uranyl sulphate solution, which is similar to composition used in uranium hydrometallurgy, was studied by chemical equivalent method. In the given range, the ratio of HSO 4 - to SO 4 2- on the resin is dependent on concentration of H + and ionic strength (μ) of solution, but it is independent of other anions sorbed on the resin. When the solution has μ of 0.1 to 0.5, pH of 1.5 to 1.9 and 0.5 x 10 -3 to 2.0 x 10 -3 M of uranium, the value of n in complex UO 2 (SO 4 ) n 2-2n is 2.5 to 2.7. The uranium occupies about 30% to 50% of total resin capacity

Sorption Efficiency of a New Sorbent towards Cadmium(II: Methylphosphonic Acid Grafted Polystyrene Resin

Directory of Open Access Journals (Sweden)

Nacer Ferrah

2013-01-01

Full Text Available A new chelating polymeric sorbent has been developed using polystyrene resin grafted with phosphonic acid. After characterization by FTIR and elementary analysis, the new resin has been investigated in liquid-solid extraction of cadmium(II. The results indicated that phosphonic resin could adsorb Cd(II ion effectively from aqueous solution. The adsorption was strongly dependent on the pH of the medium and the optimum pH value level for better sorption was between 3.2 and 5.2. The influence of other analytical parameters including contact time, amount of resin, metal ion concentration, and the presence of some electrolytes was investigated. The maximum uptake capacity of Cd(II ions was 37,9 mg·g−1 grafted resin at ambient temperature, at an initial pH value of 5.0. The overall adsorption process was best described by pseudo second-order kinetic. When Freundlich and Langmuir isotherms were tested, the latter had a better fit with the experimental data. Furthermore, more than 92% of Cd(II could be eluted by using 1.0 mol·L−1 HCl in one cycle.

Decomposing method for ion exchange resin

International Nuclear Information System (INIS)

Sako, Takeshi; Sato, Shinshi; Akai, Yoshie; Moniwa, Shinobu; Yamada, Kazuo

1998-01-01

The present invention concerns a method of decomposing ion exchange resins generated in a nuclear power plant to carbon dioxide reliably in a short period of time. (1) The ion exchange resins are mixed with water, and then they are kept for a predetermined period of time in the presence of an inert gas at high temperature and high pressure exceeding the critical point of water to decompose the ion exchange resins. (2) The ion exchange resins is mixed with water, an oxidant is added and they are kept for a predetermined time in the presence of an inert gas at a high temperature and a high pressure exceeding a critical point of water of an inert gas at a high temperature to decompose the ion exchange resins. (3) An alkali or acid is added to ion exchange resins and water to control the hydrogen ion concentration in the solution and the ion exchange resins are decomposed in above-mentioned (1) or (2). Sodium hydroxide is used as the alkali and hydrochloric acid is used as the acid. In addition, oxygen, hydrogen peroxide or ozone is used as an oxidant. (I.S.)

Method of heat decomposition for chemical decontaminating resin waste

International Nuclear Information System (INIS)

Kikuchi, Akira.

1988-01-01

Purpose: To make resin wastes into non-deleterious state, discharge them into a resin waste storage tank of existent radioactive waste processing facility and store and dispose them. Constitution: In the processing of chemical decontaminating resin wastes, iron exchange resins adsorbing chemical decontaminating agents comprising a solution of citric acid, oxalic acid, formic acid and EDTA alone or as a mixture of them are heated to dry, thermally decomposed and then separated from the ion exchange resins. That is, the main ingredients of the chemical decontaminating agents are heat-decomposed when heated and dried at about 250 deg C in air and converted into non-toxic gases such as CO, CO 2 , NO, NO 2 or H 2 O. Further, since combustion or carbonization of the basic materials for the resin is not caused at such a level of temperature, the resin wastes removed with organic acid and chelating agents are transferred to an existent resin waste storage tank and stored therein. In this way, facility cost and radiation exposure can remarkably be decreased. (Kamimura, M.)

Resin acids as the potential growth-affecting component of pine oleoresin

Directory of Open Access Journals (Sweden)

T. J. Wodzicki

2015-01-01

Full Text Available The nonvolatile fraction of the oleoresin of Pinus sihestris L. was found to contain substances which inhibit growth of wheat ceoleoptile and oat mesocotyl sections in standard bioassays. The inhibition is mainly confined to the fraction of resin acids. Among the seven authentic resin acids tested, the effects of dehydroabietic and abietic acids were most sifgnificant. Palustric, pimaric and isopimaric acids were not effective in the wheat coleoptile section straight growth test. None of the substances, in the amounts tested, except for extremely high concentration, exerted an inhibitory effect on natural or IAA-induced elongation of pine hypocotyl sections. Neither was an inhibitory effect discovered in the microbiological test with the Aspergillus niger van Tiegh. The results obtained with pine hypocotyl sections, allow the conclusion that resin acids interfering with the results of standard bioassays are probably not effective as inhibitory factors in the regulation of pine tissue growth.

Synthesis of iminodi(methylphosphonic acid)-type chitosan resin and its adsorption behavior for trace metals

International Nuclear Information System (INIS)

Yamakawa, Satoko; Oshita, Koji; Sabarudin, Akhmad; Oshima, Mitsuko; Motomizu, Shoji

2004-01-01

A chitosan-based resin possessing the iminodi(methyphosphonic acid) moiety (IDP-type chitrosan resin) was synthesized by using cross-linked chitosan as a base material. The adsorption behavior of trace metal ions on the IDP-type chitosan resin was systematically investigated using a mini-column (1 ml of the resin) packed with the resin. The concentrations of metal ions in the effluents were measured by ICP-MS and ICP-AES. The resin could adsorb four metals, such as In(III), Sn(II), Th(IV), and U(VI), by almost 100% over a wide pH range (1-7). Uranium(VI) and thorium could not be eluted with nitric acid and hydrochloric acid (1-6 M); other metal ions were easily and readily eluted with 1 M nitric acid. The IDP-type chitosan resin synthesized in this work can be applied to the separation of U(VI) and Th(IV) from other metal ions. (author)

Effect of different solutions on color stability of acrylic resin-based dentures

Directory of Open Access Journals (Sweden)

Marcelo Coelho Goiato

2014-01-01

Full Text Available The aim of this study was to evaluate the effect of thermocycling and immersion in mouthwash or beverage solutions on the color stability of four different acrylic resin-based dentures (Onda Cryl, OC; QC20, QC; Classico, CL; and Lucitone, LU. The factors evaluated were type of acrylic resin, immersion time, and solution (mouthwash or beverage. A total of 224 denture samples were fabricated. For each type of resin, eight samples were immersed in mouthwashes (Plax-Colgate, PC; Listerine, LI; and Oral-B, OB, beverages (coffee, CP; cola, C; and wine, W, and artificial saliva (AS; control. The color change (DE was evaluated before (baseline and after thermocycling (T1, and after immersion in solution for 1 h (T2, 3 h (T3, 24 h (T4, 48 h (T5, and 96 h (T6. The CIE Lab system was used to determine the color changes. The thermocycling test was performed for 5000 cycles. Data were submitted to three-way repeated-measures analysis of variance and Tukey's test (p < 0.05. When the samples were immersed in each mouthwash, all assessed factors, associated or not, significantly influenced the color change values, except there was no association between the mouthwash and acrylic resin. Similarly, when the samples were immersed in each beverage, all studied factors influenced the color change values. In general, regardless of the solution, LU exhibited the greatest DE values in the period from T1 to T5; and QC presented the greatest DE values at T6. Thus, thermocycling and immersion in the various solutions influenced the color stability of acrylic resins and QC showed the greatest color alteration.

Effect of different solutions on color stability of acrylic resin-based dentures.

Science.gov (United States)

Goiato, Marcelo Coelho; Nóbrega, Adhara Smith; dos Santos, Daniela Micheline; Andreotti, Agda Marobo; Moreno, Amália

2014-01-01

The aim of this study was to evaluate the effect of thermocycling and immersion in mouthwash or beverage solutions on the color stability of four different acrylic resin-based dentures (Onda Cryl, OC; QC20, QC; Classico, CL; and Lucitone, LU). The factors evaluated were type of acrylic resin, immersion time, and solution (mouthwash or beverage). A total of 224 denture samples were fabricated. For each type of resin, eight samples were immersed in mouthwashes (Plax-Colgate, PC; Listerine, LI; and Oral-B, OB), beverages (coffee, CP; cola, C; and wine, W), and artificial saliva (AS; control). The color change (DE) was evaluated before (baseline) and after thermocycling (T1), and after immersion in solution for 1 h (T2), 3 h (T3), 24 h (T4), 48 h (T5), and 96 h (T6). The CIE Lab system was used to determine the color changes. The thermocycling test was performed for 5000 cycles. Data were submitted to three-way repeated-measures analysis of variance and Tukey's test (p<0.05). When the samples were immersed in each mouthwash, all assessed factors, associated or not, significantly influenced the color change values, except there was no association between the mouthwash and acrylic resin. Similarly, when the samples were immersed in each beverage, all studied factors influenced the color change values. In general, regardless of the solution, LU exhibited the greatest DE values in the period from T1 to T5; and QC presented the greatest DE values at T6. Thus, thermocycling and immersion in the various solutions influenced the color stability of acrylic resins and QC showed the greatest color alteration.

Adsorption characteristics of 14C-labeled alanine, aspartic acid and adenosine triphosphate by metal-chelating resins

International Nuclear Information System (INIS)

Ishiyama, Toshio; Matsunami, Tadao; Shibata, Setsuko; Honda, Yoshihide.

1987-01-01

(1) Adsorption properties of 14 C-alanine, 14 C-ATP (adenosine triphosphate) and 14 C-aspartic acid on the metal-chelating resins were determined and found that the Cu(II)-Chelex 100 and Fe(III)-Unicellex UR10, Fe(III)-Chelex 100 chelating resins were highly effective for the adsorption of 14 C-alanine and 14 C-ATP, respectively. (2) Desorption rate of 14 C-ATP from the Fe(III)-Unicellex UR10 and Fe(III)-Chelex 100 resins was somewhat higher than the case of 14 C-alanine, probably because the coordination bonds of Cu-alanine might be stronger than those of Fe-ATP. Thus, 14 C-labeled organic compounds such as 14 C-alanine and 14 C-ATP of a low activity concentration (3.7 mBq/ml) (1 x 10 -7 μCi/ml) in aqueous solution may be measured with liquid scintillation counter after pre-concentration by use of the Fe(III)- and Cu(II)-chelating resin columns. (author)

Separation of aliphatic carboxylic acids and benzenecarboxylic acids by ion-exclusion chromatography with various cation-exchange resin columns and sulfuric acid as eluent.

Science.gov (United States)

Ohta, Kazutoku; Ohashi, Masayoshi; Jin, Ji-Ye; Takeuchi, Toyohide; Fujimoto, Chuzo; Choi, Seong-Ho; Ryoo, Jae-Jeong; Lee, Kwang-Pill

2003-05-16

The application of various hydrophilic cation-exchange resins for high-performance liquid chromatography (sulfonated silica gel: TSKgel SP-2SW, carboxylated silica gel: TSKgel CM-2SW, sulfonated polymethacrylate resin: TSKgel SP-5PW, carboxylated polymethacrylate resins: TSKgel CM-5PW and TSKgel OA-Pak A) as stationary phases in ion-exclusion chromatography for C1-C7 aliphatic carboxylic acids (formic, acetic, propionic, butyric, isovaleric, valeric, isocaproic, caproic, 2-methylhexanoic and heptanoic acids) and benzenecarboxylic acids (pyromellitic, trimellitic, hemimellitic, o-phthalic, m-phthalic, p-phthalic, benzoic, salicylic acids and phenol) was carried out using diluted sulfuric acid as the eluent. Silica-based cation-exchange resins (TSKgel SP-2SW and TSKgel CM-2SW) were very suitable for the ion-exclusion chromatographic separation of these benzenecarboxylic acids. Excellent simultaneous separation of these benzenecarboxylic acids was achieved on a TSKgel SP-2SW column (150 x 6 mm I.D.) in 17 min using a 2.5 mM sulfuric acid at pH 2.4 as the eluent. Polymethacrylate-based cation-exchange resins (TSKgel SP-5PW, TSKgel CM-5PW and TSKgel OA-Pak A) acted as advanced stationary phases for the ion-exclusion chromatographic separation of these C1-C7 aliphatic carboxylic acids. Excellent simultaneous separation of these C1-C7 acids was achieved on a TSKgel CM-5PW column (150 x 6 mm I.D.) in 32 min using a 0.05 mM sulfuric acid at pH 4.0 as the eluent.

Boron removal from aqueous solutions by ion-exchange resin: Column sorption-elution studies

International Nuclear Information System (INIS)

Koese, T. Ennil; Oztuerk, Nese

2008-01-01

A column sorption-elution study was carried out by using a strong base anion-exchange resin (Dowex 2 x 8) for the removal of boron from aqueous solutions. The breakthrough curve was obtained as a function of feed flow rate and the total and breakthrough capacity values of the resin were calculated. The boron on the resin was quantitatively eluted with 0.5 M HCl solution at different flow rates. Three consecutive sorption-elution-washing-regeneration-washing cycles were applied to the resin in order to investigate the reusability of the ion-exchange resin. Total capacity values remained almost the same after three sorption-elution-regeneration cycles. The Thomas and the Yoon-Nelson models were applied to experimental data to predict the breakthrough curves and to determine the characteristic column parameters required for process design. The results proved that the models would describe the breakthrough curves well

Study on removing chlorin by conversion-aborption of chlorin resin

International Nuclear Information System (INIS)

Huang Yunbai; Zhao Jinfang; Tang Zhijuan; Huang Qijin; Deng Jianguo

2012-01-01

Theon version of chlorin resin and the reclamation of acid and uranium in converting solution were investigated. The results indicated the residual chlorin can meet the requirement after converting, acid and uranium in converting solution can be reclaimed. (authors)

Surface roughness of composite resins subjected to hydrochloric acid.

Science.gov (United States)

Roque, Ana Carolina Cabral; Bohner, Lauren Oliveira Lima; de Godoi, Ana Paula Terossi; Colucci, Vivian; Corona, Silmara Aparecida Milori; Catirse, Alma Blásida Concepción Elizaur Benitez

2015-01-01

The purpose of this study was to determine the influence of hydrochloric acid on surface roughness of composite resins subjected to brushing. Sixty samples measuring 2 mm thick x 6 mm diameter were prepared and used as experimental units. The study presented a 3x2 factorial design, in which the factors were composite resin (n=20), at 3 levels: microhybrid composite (Z100), nanofilled composite (FiltekTM Supreme), nanohybrid composite (Ice), and acid challenge (n=10) at 2 levels: absence and presence. Acid challenge was performed by immersion of specimens in hydrochloric acid (pH 1.2) for 1 min, 4 times per day for 7 days. The specimens not subjected to acid challenge were stored in 15 mL of artificial saliva at 37 oC. Afterwards, all specimens were submitted to abrasive challenge by a brushing cycle performed with a 200 g weight at a speed of 356 rpm, totaling 17.8 cycles. Surface roughness measurements (Ra) were performed and analyzed by ANOVA and Tukey test (p≤0.05). Surface roughness values were higher in the presence (1.07±0.24) as compared with the absence of hydrochloric acid (0.72±0.04). Surface roughness values were higher for microhybrid (1.01±0.27) compared with nanofilled (0.68 ±0.09) and nanohybrid (0.48±0.15) composites when the specimens were not subjects to acid challenge. In the presence of hydrochloric acid, microhybrid (1.26±0.28) and nanofilled (1.18±0,30) composites presents higher surface roughness values compared with nanohybrid (0.77±0.15). The hydrochloric acid affected the surface roughness of composite resin subjected to brushing.

Effect of the chemical structure of anion exchange resin on the adsorption of humic acid: behavior and mechanism.

Science.gov (United States)

Shuang, Chendong; Wang, Jun; Li, Haibo; Li, Aimin; Zhou, Qing

2015-01-01

Polystyrenic (PS) anion-exchange resin and polyacrylic (PA) anion-exchange resin were used to investigate the effect of resin chemical structure on the adsorption of humic acid (HA). Due to the rearrangement of HA to form layers that function as barricades to further HA diffusion, PS resin exhibited 12.4 times slower kinetics for the initial adsorption rate and 8.4 times for the diffusion constant in comparison to that of the PA resin. An HA layer and a spherical cluster of HA can be observed on the surface of the PS and PA resins after adsorption, respectively. The considerable difference in HA adsorption between the PS and PA resins was due to the difference in molecule shape for interaction with different resin structures, which can essentially be explained by the hydrophobicity and various interactions of the PS resin. A given amount of HA occupies more positively charged sites and hydrophobic sites on the PS resin than were occupied by the same amount of HA on the PA resin. Increased pH resulted in an increase of HA adsorption onto the PA resin but a decrease in adsorption onto PS resin, as the non-electrostatic adsorption led to electrostatic repulsion between the HA attached to the resin and the HA dissolved in solution. These results suggest higher rates of adsorption and higher regeneration efficiency for interaction of HA with more hydrophilic anion exchange materials. Copyright © 2014 Elsevier Inc. All rights reserved.

SEPARATION OF BARIUM VALUES FROM URANYL NITRATE SOLUTIONS

Science.gov (United States)

Tompkins, E.R.

1959-02-24

The separation of radioactive barium values from a uranyl nitrate solution of neutron-irradiated uranium is described. The 10 to 20% uranyl nitrate solution is passed through a flrst column of a cation exchange resin under conditions favoring the adsorption of barium and certain other cations. The loaded resin is first washed with dilute sulfuric acid to remove a portion of the other cations, and then wash with a citric acid solution at pH of 5 to 7 to recover the barium along with a lesser amount of the other cations. The PH of the resulting eluate is adjusted to about 2.3 to 3.5 and diluted prior to passing through a smaller second column of exchange resin. The loaded resin is first washed with a citric acid solution at a pH of 3 to elute undesired cations and then with citric acid solution at a pH of 6 to eluts the barium, which is substantially free of undesired cations.

Extraction behaviour of Am(III) and Eu(III) from nitric acid medium in CMPO-HDEHP impregnated resins

Energy Technology Data Exchange (ETDEWEB)

Saipriya, K.; Kumar, T. [Bhabha Atomic Research Centre Facilities (India). Kalpakkam Reproscessing Plants; Kumaresan, R.; Nayak, P.K.; Venkatesan, K.A.; Antony, M.P. [Indira Gandhi Center for Atomic Research, Kalpakkam (India). Fuel Chemistry Div.

2016-05-01

Chromatographic resin containing extractants such as octyl(phenyl)-N,N-diisobutylcarbamoylmethylphosphine oxide (CMPO) or bis-(2-ethylhexyl)phosphoric acid (HDEHP) or mixture of extractants (CMPO + HDEHP) in an acrylic polymer matrix was prepared and studied for the extraction of Am(III) and Eu(III) over a range of nitric acid concentration. The effect of various parameters such as concentration of nitric acid in aqueous phase and the concentration of CMPO and HDEHP in the resin phase was studied. The distribution coefficient of Am(III) and Eu(III) in the impregnated resin increased with increased in the concentration of nitric acid for CMPO-impregnated resin, whereas a reverse trend was observed in HDEHP impregnated resin. In case of resin containing both the extractants, synergism was observed at low nitric acid concentration and antagonism at high nitric acid concentration. The mechanism of extraction was probed by slope analysis method at 0.01 and 2 M nitric acid concentrations. Citrate-buffered DTPA was used for the selective separation of Am(III), and a separation factor of 3-4 was obtained at pH 3.

Releasing Pattern of Applied Phosphorus and Distribution Change of Phosphorus Fractions in the Acid Upland Soils with Successive Resin Extraction

Directory of Open Access Journals (Sweden)

Arief Hartono

2008-05-01

Full Text Available The releasing pattern of applied P in the acid upland soils and the soil properties influencing the pattern were studied. Surface horizons of six acid upland soils from Sumatra, Java and Kalimantan were used in this study. The releasing pattern of applied P (300 mg P kg-1 of these soils were studied by successive resin extraction. P fractionation was conducted to evaluate which fractions released P to the soil solution after successive resin extraction. The cumulative of resin-Pinorganic (Pi release of soils was fitted to the first order kinetic. Regression analyses using factor scores obtained from the previous principal components analyses was applied to determine soil properties influencing P releasing pattern. The results suggested that the maximum P release was significantly (P < 0.05 increased by acidity plus 1.4 nm mineral-related factor (PC2 i.e. exchangeable Al and 1.4 nm minerals (smectite and vermiculite and decreased by oxide related factor (PC1 i.e. aluminum (Al plus 1/2 iron (Fe (by ammonium oxalate, crystalline Al and Fe oxides, cation exchange capacity, and clay content. P fractionation analysis after successive resin extraction showed that both labile and less labile in the form of NaHCO3-Pi and NaOH-Pi fractions, respectively, can be transformed into resin-Pi when in the most labile resin-Pi is depleted. Most of P released in high oxides soils were from NaOH-Pi fraction while in low oxides soils were from NaHCO3-Pi. P release from the former fraction resulted in the maximum P release lower than that of the latter one. When NaHCO3-Pi was high, NaOH-Pi was relatively more stable than NaHCO3-Pi despite resin-Pi removal. NaHCO3-Pi and NaOH-Pi are very important P fractions in replenishing resin-Pi in these acid upland soils.

Fatty Acid-Based Monomers as Styrene Replacements for Liquid Molding Resins

Science.gov (United States)

2005-05-01

fatty acid length and unsaturation level on resin and polymer properties. Fig. 2. The addition of fatty acids ( oleic acid ) to glycidyl methacylate to...the synthetic route used to form the methacrylated fatty acids (MFA). The carboxylic acid of fatty acids undergoes a simple addition reaction with... form methacrylated fatty acid monomer

CHEMICAL COMPOSITIONS OF PINE RESIN, ROSIN AND TURPENTINE OIL FROM WEST JAVA

Directory of Open Access Journals (Sweden)

Bambang Wiyono

2006-03-01

Full Text Available This study was conducted to identify chemical composition of merkus pine resin, rosin and turpentine oil. Initially, pine resin was separated into neutral and acidic fractions with an aqueous 4% sodium hydroxide solution. After methylation, the fraction containing turpentine oil and rosin were analyzed by gas chromatography (GC, and gas chromatograph mass spectrometry (GC-MS, respectively. The neutral fraction of pine resin and turpentine oil mainly consisted of a-pinene, D-3-carene and b-pinene. Based on mass spectral comparison, the major constituents of the acidic fraction and rosin were identified as sandaracopimaric acid, isopimaric acid, palustric acid, dehydroabietic acid, abietic acid, neoabietic acid, and merkusic acid. The major component of the acidic fractions was palustric acid, while that of rosin was abietic acid. Using TC (tough column 1 and TC 5 columns, levopimaric acid could not be separated from rosin or acidic fraction of pine resin of Indonesian Pinus merkusii.

Biogenic glutamic acid-based resin: Its synthesis and application in the removal of cobalt(II)

International Nuclear Information System (INIS)

Jamiu, Zakariyah A.; Saleh, Tawfik A.; Ali, Shaikh A.

2017-01-01

Highlights: • A novel resin embedded with metal chelating glutamic acid was synthesized. • The biogenic amino acid residues imparted remarkable efficacy to remove Co(II). • The resin showed excellent ability to remove various metals from wastewater. - Abstract: Inexpensive biogenic glutamic acid has been utilized to synthesize a cross-linked dianionic polyelectrolyte (CDAP) containing metal chelating ligands. Cycloterpolymerization, using azoisobutyronitrile as an initiator, of N,N-diallylglutamic acid hydrochloride, sulfur dioxide and a cross-linker afforded a pH-responsive cross-linked polyzwitterionic acid (CPZA) which upon basification with NaOH was converted into CDAP. The new resin, characterized by a multitude of spectroscopic techniques as well as Scanning Electron Microscopy (SEM) and Brunauer–Emmett–Teller (BET) analyses, was evaluated for the removal of Co(II) as a model case under different conditions. The adsorption capacity of 137 mg g"−"1 does indeed make the resin as one of the most effective sorbents in recent times. The resin leverages its cheap natural source and ease of regeneration in combination with its high and fast uptake capacities to offer a great promise for wastewater treatment. The resin has demonstrated remarkable efficiency in removing toxic metal ions including arsenic from a wastewater sample.

Biogenic glutamic acid-based resin: Its synthesis and application in the removal of cobalt(II)

Energy Technology Data Exchange (ETDEWEB)

Jamiu, Zakariyah A.; Saleh, Tawfik A.; Ali, Shaikh A., E-mail: shaikh@kfupm.edu.sa

2017-04-05

Highlights: • A novel resin embedded with metal chelating glutamic acid was synthesized. • The biogenic amino acid residues imparted remarkable efficacy to remove Co(II). • The resin showed excellent ability to remove various metals from wastewater. - Abstract: Inexpensive biogenic glutamic acid has been utilized to synthesize a cross-linked dianionic polyelectrolyte (CDAP) containing metal chelating ligands. Cycloterpolymerization, using azoisobutyronitrile as an initiator, of N,N-diallylglutamic acid hydrochloride, sulfur dioxide and a cross-linker afforded a pH-responsive cross-linked polyzwitterionic acid (CPZA) which upon basification with NaOH was converted into CDAP. The new resin, characterized by a multitude of spectroscopic techniques as well as Scanning Electron Microscopy (SEM) and Brunauer–Emmett–Teller (BET) analyses, was evaluated for the removal of Co(II) as a model case under different conditions. The adsorption capacity of 137 mg g{sup −1} does indeed make the resin as one of the most effective sorbents in recent times. The resin leverages its cheap natural source and ease of regeneration in combination with its high and fast uptake capacities to offer a great promise for wastewater treatment. The resin has demonstrated remarkable efficiency in removing toxic metal ions including arsenic from a wastewater sample.

Characterization of the sorption of uranium(VI) on different complexing resins

Energy Technology Data Exchange (ETDEWEB)

Pesavento, Maria; Biesuz, Raffaela; Alberti, Giancarla; Sturini, Michela [Dipartimento di Chimica Generale dell' Universita degli Studi di Pavia, Via Taramelli 12, 27100, Pavia (Italy)

2003-08-01

The sorption of uranium(VI) on two cationic resins containing different complexing groups, the iminodiacetic resin Chelex 100 and the weak carboxylic resin Amberlite CG-50, was investigated. The Gibbs-Donnan model was used to describe and to predict the sorption through the determination of the intrinsic complexation constants. These quantities, even though non-thermodynamic, characterize the sorption as being independent of experimental conditions. The sorption mechanism of the metal on the complexing resins was also studied by adding a competitive soluble ligand that shifts the sorption curves to higher pH values. The ligand competes with the resin for the complexation with the metal ion. Uranium is also strongly sorbed on Chelex 100 at very acid pH, through formation of two complexes in the resin phase: ML with log{beta}{sub 110i}=-1.16, in more acidic solution, and ML{sub 2}with log {beta}{sub 120i}=-5.72. Only the presence of the competitive ligand in solution makes the determination of the second complex possible. Also on Amberlite CG-50 the sorption is strong and involves the formation of the complex ML {sub 2}, in more acidic solution, with log {beta}{sub 120i}=-3.16. In the presence of the ligand EDTA, the complex ML {sub 2}(OH) {sub 2}was characterized with log {beta}{sub 12-2i}=-5.15. In all the experiments the hydrolysis reaction in the aqueous phase was quantitatively considered. (orig.)

Characterization of the sorption of uranium(VI) on different complexing resins

International Nuclear Information System (INIS)

Pesavento, Maria; Biesuz, Raffaela; Alberti, Giancarla; Sturini, Michela

2003-01-01

The sorption of uranium(VI) on two cationic resins containing different complexing groups, the iminodiacetic resin Chelex 100 and the weak carboxylic resin Amberlite CG-50, was investigated. The Gibbs-Donnan model was used to describe and to predict the sorption through the determination of the intrinsic complexation constants. These quantities, even though non-thermodynamic, characterize the sorption as being independent of experimental conditions. The sorption mechanism of the metal on the complexing resins was also studied by adding a competitive soluble ligand that shifts the sorption curves to higher pH values. The ligand competes with the resin for the complexation with the metal ion. Uranium is also strongly sorbed on Chelex 100 at very acid pH, through formation of two complexes in the resin phase: ML with logβ 110i =-1.16, in more acidic solution, and ML 2 with log β 120i =-5.72. Only the presence of the competitive ligand in solution makes the determination of the second complex possible. Also on Amberlite CG-50 the sorption is strong and involves the formation of the complex ML 2 , in more acidic solution, with log β 120i =-3.16. In the presence of the ligand EDTA, the complex ML 2 (OH) 2 was characterized with log β 12-2i =-5.15. In all the experiments the hydrolysis reaction in the aqueous phase was quantitatively considered. (orig.)

Device for processing regenerative wastes of ion exchange resin

International Nuclear Information System (INIS)

Kuroda, Osamu; Ebara, Katsuya; Shindo, Toshikazu; Takahashi, Sankichi

1986-01-01

Purpose: To facilitate the operation and maintenance of a processing device by dividing radioactive wastes produced in the regenerative process of ion exchange resin into a regenerated usable recovery liquid and wastes. Constitution: Sulfuric acid is recovered by a diffusion dialysis method from wastes containing sulfuric acid that are generated in the regenerative process of cation-exchange resin and also caustic soda is recovered by the diffusion dialysis method from wastes containing caustic soda that are generated in the regenerative process of anion-exchange resin. The sulfuric acid and caustic soda thus recovered are used for the regeneration of ion-exchange resin. A concentrator is provided for concentrating the sulfuric acid and caustic soda water solution to concentration suitable for the regeneration of these ion-exchange resins. Also provided is a recovery device for recovering water generated from the concentrator. This device is of so simple a constitution that its operation and maintenance can be performed very easily, thereby greatly reducing the quantity of waste liquid required to be stored in drums. (Takahashi, M.)

Synthesis of a magnetic composite resin and its cobalt removal characteristics in aqueous solution

International Nuclear Information System (INIS)

Kim, Young Kyun; Lee, Kun Jai

2001-01-01

A series of stepwise procedures to prepare a new organic-inorganic composite magnetic resin with phenolsulphonic-formaldehyde and freshly formed iron ferrite was established, based upon wet-and-neutralization method for synthesizing iron ferrite and pearl-polymerization method for synthesizing rigid bead-type composite resin. The ion exchange and sorption characteristics of the composite resin prepared by the above method at various conditions were experimentally disclosed. The composite resin prepared shows stably high removal efficiency to Co(II) species in aqueous solution in a wide range of solution pH. The overall isotherm is qualitatively explained by the generalized adsorption isotherm concept proposed by McKinley. The standard enthalpy change derived from van't Hoff equation conforms to the typical range for chemisorption or ion exchange. The selectivity of the PSF-F (phenolsulphonic formaldehyde-iron ferrite) composite resin to Co(II) species and other competing chemicals (i.e. Na 2 EDTA, Ca(II) and Na) was compared. It is anticipated that the composite resin can also be used for column-operation with process-control by applying external magnetic field, since the rigid bead-type composite resin shows magnetic-susceptibility due to its paramagnetic inorganic constituent (i.e. iron ferrite). (author)

Oxidative degradation of ion-exchange resins in acid medium. Vol. 3

International Nuclear Information System (INIS)

Eskander, S.B.; Ghattas, N.K.

1996-01-01

Volume reduction of spent ion-exchange resins used in nuclear facilities receive increasing importance due to the increase in storage cost, unstable physical and chemical properties and their relatively high specific activity (in some cases up to 1 Ci per liter). The present study is part of research program on the treatment and immobilization of radioactive spent ion-exchange resins simulate; hydrogen peroxide was used for the oxidative degradation of spent ion-exchange resins simulate in sulphuric acid medium. Five liters ring digester developed in Karlsruhe nuclear research center-(KFK)- in germany was the chosen option to perform the oxidation process. The work reported focused on the kinetics and mechanism of the oxidation process. Heating the organic resins in sulphuric acid results in its carbonization and partial oxidation of only 1.7% of the carbon added. Results show that the oxidation reaction is a relatively slow process of first order with K value in the order of 10 -4 min -1 , and the main oxidation product was carbon dioxide. The production of carbon oxide in the off gas stream increased sharply by the addition of hydrogen peroxide to the hot sulphuric acid-resin mixture. The results obtained show that more than 97% of the carbon added was oxidized to carbon dioxide and carbon monoxide. The rate constant value (K) of this reaction was calculated to be (1.69±0.13) x 10 -2 min -1 . The results of gas chromatographic analysis indicate that no significant amounts of hazardous organic materials were detected in the off-gas streams. 6 figs., 4 tabs

Determination of humic acid in alkali leaching solution of uranium by spectophotrometry-COD method

International Nuclear Information System (INIS)

Feng Yu; An Wei; Chen Shusen

2014-01-01

It is one of the main causes of extraction emulsification or resin toxicosis during alkali leaching process in uranium metallurgy which organic matters including humic acid exist in lixiviums. In order to study the effect of humic acid in uranium metallurgy, a method for determination of content of humic acid in aqueous solution need to be established. Spectrophotometry is a simple and convenient method in humic acid analysis. However, accuracy of spectrophotometry can be reduced greatly because of interference of uranium and other elements in the humic acid solutions. Although chemical oxygen demand (COD) method is a common analysis way of organic matters in aqueous solutions, the concentration of humic acid cannot be directly measured. In this paper, COD method is related with spectrophotometry to avoid the interference of uranium and ensure the accurate analysis of humic acid. The results showed that the detection limit of the method was 1.78 mg/L and the recovery rate was 101.2%. (authors)

Speciation and surface interactions of actinides on aged ion-exchange resins

International Nuclear Information System (INIS)

Morris, D.E.; Buscher, C.T.; Donohoe, R.J.

1997-01-01

The United States Department of Energy is presently faced with the stabilization and safe disposition of hundreds of metric tons of residue materials resulting from 50+ years of nuclear weapons production activities. These residues encompass a broad range of substrates and radionuclides and include both solid and liquid materials. Combustible residues constitute a significant fraction of the total residue inventory, and an important constituent within the combustible category is spent anion ion-exchange resins. These resins are typically utilized for the separation of plutonium from other radionuclides under strongly acidic nitric or hydrochloric acid solution conditions which favor the formation and partitioning of anionic Pu(IV) nitrato or chloride species. The spent resins are usually rinsed prior to storage as residues to reduce both acid and radionuclide concentrations, but significant radionuclide concentrations remain in these resins, and the long-term effects of concentrated acid and radiolysis on the resin integrity are relatively unexplored. Thus, new research is needed to assess the stability of these resin residues and address the need for further treatment to ensure stability prior to long-term disposal

[Effect of hydrofluoric acid concentration on the surface morphology and bonding effectiveness of lithium disilicate glass ceramics to resin composites].

Science.gov (United States)

Hailan, Qian; Lingyan, Ren; Rongrong, Nie; Xiangfeng, Meng

2017-12-01

This study aimed at determining the influence of hydrofluoric acid (HF) in varied concentrations on the surface morphology of lithium disilicate glass ceramics and bond durability between resin composites and post-treated lithium disilicate glass ceramics. After being sintered, ground, and washed, 72 as-prepared specimens of lithium disilicate glass ceramics with dimensions of 11 mm×13 mm×2 mm were randomly divided into three groups. Each group was treated with acid solution [32% phosphoric acid (PA) or 4% or 9.5% HF] for 20 s. Then, four acidified specimens from each group were randomly selected. One of the specimens was used to observe the surface morphology using scanning electron microscopy, and the others were used to observe the surface roughness using a surface roughness meter (including Ra, Rz, and Rmax). After treatment with different acid solutions in each group, 20 samples were further treated with silane coupling agent/resin adhesive/resin cement (Monobond S/Multilink Primer A&B/Multilink N), followed by bonding to a composite resin column (Filtek™ Z350) with a diameter of 3 mm. A total of 20 specimens in each group were randomly divided into two subgroups, which were used for measuring the microshear bond strength, with one of them subjected to cool-thermal cycle for 20 000 times. The surface roughness (Ra, Rz, and Rmax) of lithium disilicate glass ceramics treated with 4% or 9.5% HF was significantly higher than that of the ceramic treated with PA (Pglass ceramics treated with 9.5% HF also demonstrated better surface roughness (Rz and Rmax) than that of the ceramics treated with 4% HF. Cool-thermal cycle treatment reduced the bond strength of lithium disilicate glass ceramics in all groups (Pglass ceramics treated with HF had higher bond strength than that of the ceramics treated with PA. The lithium disilicate glass ceramics treated with 4% HF had higher bond strength than that of the ceramics treated with 9.5% HF (Pglass ceramics treated with 4

On-line gross alpha radiation monitoring of natural waters with extractive scintillating resins

International Nuclear Information System (INIS)

Hughes, Lara; De Vol, T.A.

2003-01-01

Extractive scintillating resins, which are used to simultaneously separate and quantify radioactivity in aqueous solutions, were developed for low-level alpha radiation monitoring of natural waters. Resins were investigated with bis(2-ethylhexyl)methane-diphosphonic acid (H 2 DEH[MDP], Dipex[reg]) extractant, which has a strong affinity for tri-, tetra- and hexavalent actinides in dilute acids. Extractive scintillating resins were manifested (1) as a mixed bed of scintillating resin and extraction chromatographic resin and (2) by diffusing the organic fluor 2-(1-naphtyl)-5-phenyloxazole into macroporous polystyrene chromatographic resin, then coating with H 2 DEH[MDP], or by coating H 2 DEH[MDP] on scintillating polyvinyltoluene beads. The scintillation light was detected with a modified Hidex Triathler to allow for continuous flow measurements. The average detection efficiencies were 51.7±2.6% and 65.8±10.1% for natural uranium and 241 Am, respectively, for the extractant coated scintillator. The resin was stable for solution flow of up to 1000 ml resulting in rapid real-time quantification of natural uranium in groundwater down to 30 μg/ml

Recovery of tretrachloroaurate through ion exchange with Dowex 11 resin

International Nuclear Information System (INIS)

Alguacil, F.J.

1998-01-01

The recovery of the tretrachloroaurate complex by the anionic ion exchange resin Dowex 11 has been studied. The kinetics of gold adsorption were dependent of both gold and resin concentrations and temperature. The adsorption isotherm can be described by the expression Q=kC''n. The loaded resin could be eluted by an acidic thiourea solution at 20 degree centigree. After several adsorption-elution cycles there is not any apparent loss in the adsorption properties of the resin. (Author) 6 refs

Synthesis and characterization of an N-(2-hydroxyethyl)-ethylenediaminetriacetic acid resin

International Nuclear Information System (INIS)

Lai, Y.F.

1977-10-01

A chelating ion-exchange resin with N-(2-hydroxyethyl)ethylene-diaminetriacetic acid (HEDTA) used as the ligand chemically bonded to XAD-4 by an ester linkage, HEDTA-4, was synthesized. It is stable under normal experimental conditions with the liquid chromatograph. The structure of the resin was confirmed by an infrared spectrum, and by potentiometric titrations. The capacity of the resin was also obtained by potentiometric titration and by a nitrogen analysis. The resin was used to pack a column of 5 mm internal diameter and 5 cm long. The effect of pH on the retention of different metal ions on the resin was studied. It was found that the resin was most selective for chromium(III), copper(II), lead(II), mercury(II), uranium(VI), zirconium(IV) and zinc(II) at a pH of less than 3. Furthermore, the resin proves to be functioning with a chelating mechanism rather than ion-exchange, and it can concentrate trace metal ions in the presence of a large excess of calcium and magnesium. This makes the resin potentially useful for purifying and analyzing drinking water

Phenolic cation exchange resin material for recovery of cesium and strontium

Science.gov (United States)

Ebra, Martha A.; Wallace, Richard M.

1983-01-01

A phenolic cation exchange resin with a chelating group has been prepared by reacting resorcinol with iminodiacetic acid in the presence of formaldehyde at a molar ratio of about 1:1:6. The material is highly selective for the simultaneous recovery of both cesium and strontium from aqueous alkaline solutions, such as, aqueous alkaline nuclear waste solutions. The organic resins are condensation polymers of resorcinol and formaldehyde with attached chelating groups. The column performance of the resins compares favorably with that of commercially available resins for either cesium or strontium removal. By combining Cs.sup.+ and Sr.sup.2+ removal in the same bed, the resins allow significant reduction of the size and complexity of facilities for processing nuclear waste.

Flowsheet Validation For The Permanganate Digestion Of REILLEX(trademark) HPQ Anion Resin

International Nuclear Information System (INIS)

Kyser, E.

2009-01-01

The flowsheet for the digestion of Reillex(trademark) HPQ was validated both under the traditional alkaline conditions and under strongly acidic conditions. Due to difficulty in performing a pH adjustment in the large tank where this flowsheet must be performed, the recommended digestion conditions were changed from pH 8-10 to 8 M HNO 3 . Thus, no pH adjustment of the solution is required prior to performing the permanganate addition and digestion and the need to sample the digestion tank to confirm appropriate pH range for digestion may be avoided. Neutralization of the acidic digestion solution will be performed after completion of the resin digestion cycle. The amount of permanganate required for this type of resin (Reillex(trademark) HPQ) was increased from 1 kg/L resin to 4 kg/L resin to reduce the amount of residual resin solids to a minimal amount ( 2 ) solids (1.71 kg/L resin) and involves the generation of a significant liquid volume due to the low solubility of permanganate. However, since only two batches of resin (40 L each) are expected to be digested, the total waste generated is limited.

Possible mechanisms for the interaction of polymeric composite resins with Cu(II) ions in aqueous solution

International Nuclear Information System (INIS)

El-Zahhhar, A.A.; Abdel-Aziz, H.M.; Siyam, T.

2005-01-01

The interaction between the active groups of polymeric composite resins such as Poly(acrylamide-acrylic acid)-ethylenediaminetetra acetic acid disodium salt P(AM-AA)EDTANa 2 , Poly(acrylamide-acrylic acid)- montmorillonite P(AM-AA)-montmorillonite, and Poly(acrylamide-acrylic acid)-potassium nickel hexacyanoferrate P(AM-AA)-KNiHCF, with copper sulfate as a test ion has been studied. The spectroscopic studies show that the mechanism of interaction between polymeric composite resins and copper sulfate is a bond formation between the active groups of polymeric chains and copper ion. The bond formation depends on nature of polymeric chains. It was also found that the amide groups form complexes with hydrated cations, while carboxylate group interact by ion exchange mechanism through complex formation. Montmorillonite and hexacyanoferrate of the resins interact with metal ions by ion exchange mechanism

Diphonix trademark Resin: A review of its properties and applications

International Nuclear Information System (INIS)

Chiarizia, R.; Horwitz, E.P.; Alexandratos, S.D.

1995-01-01

The recently developed Diphonix trademark resin is a new multifunctional chelating ion exchange resin containing seminally substituted diphosphonic acid ligands chemically bonded to a styrene-based polymeric matrix. Diphonix can be regarded as a dual mechanism polymer, with a sulfonic acid cation exchange group allowing for rapid access, mostly non-specific, of ions into the polymeric network, and the diphosphonic acid group responsible for specificity (recognition) for a number of metal cations. The Diphonix resin exhibits an extraordinarily strong affinity for actinides, especially in the tetra- and hexavalent oxidation states. It has potential applications in TRU and mixed waste treatment and characterization, and in the development of new procedures for rapid actinide preconcentration and separation from environmental samples. Metal uptake studies have been extended to alkaline earth cations, to transition and post transition metal species, and to metal sorption from neutral or near neutral solutions. Also the kinetic behavior of the resin has been investigated in detail. Influence of the most commonly occurring matrix constituents (Na, Ca, Al, Fe, hydrofluoric, sulfuric, oxalic and phosphoric acids) on the uptake of actinide ions has been measured. This review paper summarizes the most important results studies on the Diphonix resin and gives an overview of the applications already in existence or under development in the fields of mixed waste treatment, actinide separation procedures, treatment of radwaste from nuclear power plants, and removal of iron from copper electrowinning solutions

Uranium(VI) adsorption properties of a chelating resin containing polyamine-substituted methylphosphonic acid moiety

International Nuclear Information System (INIS)

Matsuda, Masaaki; Akiyoshi, Yoshirou

1991-01-01

Uranium(VI) adsorption and desorption properties of a chelating resin containing polyamine-substituted methylphosphonic acid moiety of 2.29 mmol/g-resin (APA) were examined. Uranium(VI) adsorption properties of several ion exchange resins and extractant agents which were known as excellent adsorbents for uranium(VI), were examined together for a comparison with those of APA. Uranium(VI) adsorption capacity of APA at the concentration of 100 mg·dm -3 -uranium(VI) in 100 g·dm -3 -H 2 SO 4 aq. soln., 190 g·dm -3 -H 3 PO 4 aq. soln. and uranium enriched sea water, was 0.2, 0.05 and 0.05 mmol·g -1 respectively. The adsorption capacity of APA for uranium(VI) in these solutions was larger than that of another adsorbents, except the adsorption of uranium(VI) in enriched sea water on ion exchange resin containing phosphoric acid moiety (adsorption capacity ; 0.2 mmol·g -1 ). Uranium(VI) adsorption rate on APA was high and the relation between treatment time (t : min) and uranium(VI) concentration (y : mg·dm -3 ) in 100 g·dm -3 H 2 SO 4 aq. soln. after treatment, was shown as following equation, y=20 0.048t+1.90 (0≤t≤30). The adsorbed uranium(VI) on APA was able to be eluted with a mixed aq. soln. of hydrogen peroxide and sodium hydroxide and also was able to be eluted with an aq. alkaline soln. dissolved reduction agents such as sodium sulfite and hydrazine. From these results, it was thought that uranium(VI) adsorbed on APA was eluted due to the reduction to uranium(VI) by these eluents. (author)

Development of melamine modified urea formaldehyde resins based o nstrong acidic pH catalyzed urea formaldehyde polymer

Science.gov (United States)

Chung-Yun Hse

2009-01-01

To upgrade the performance of urea-formaldehyde (UF) resin bonded particleboards, melamine modified urea-formaldehyde (MUF) resins based on strong acidic pH catalyzed UF polymers were investigated. The study was conducted in a series of two experiments: 1) formulation of MUF resins based on a UF polymer catalyzed with strong acidic pH and 2) determination of the...

Adsorption Equilibrium Equation of Carboxylic Acids on Anion-Exchange Resins in Water.

Science.gov (United States)

Kanazawa, Nobuhiro; Urano, Kohei; Kokado, Naohiro; Urushigawa, Yoshikuni

2001-06-01

The adsorption of propionic acid and benzoic acid on anion-exchange resins was analyzed, and an adsorption equilibrium equation of carboxylic acids was proposed. The adsorption of carboxylic acids on the anion-exchange resins was considered to be the sum of the physical adsorption of the molecule and the ion-exchange adsorption of the ion, which were independent of each other. For the physical adsorption of carboxylic acids, it was conformed to the Freundlich equation. For the ion-exchange adsorption of carboxylate ions, the equilibrium equation corresponded well with the experimental results for wide ranges of concentration and pH. The equation contains a selectivity coefficient S(A)(Cl) for the chloride ion versus the carboxylate ion, which was considered essentially a constant. The influent of the bicarbonate ion from carbon dioxide in air could also be expressed by the additional equilibrium equation with the selectivity coefficient S(HCO(3))(Cl) for the chloride ion versus the bicarbonate ion. Consequently, an adsorption equilibrium equation can estimate the equilibrium adsorption amounts. Even the effect of a coexisting bicarbonate ion is inconsequential when the parameters of the Freundlich isotherm equation and the selectivity coefficients of the carboxylate ion and the bicarbonate ion in each resin are determined in advance. Copyright 2001 Academic Press.

A maturation method of uranium content in resins with acid dissolution

International Nuclear Information System (INIS)

Liu Yang

2010-01-01

Acid dissolution method is that with intensively oxidation acid to decompose ion exchanging resins and dissolving U and Fe ion in water, then menstruate the U content by titration. Comparing with our current method of filtering wash, acid dissolution menstruation U can get more accurate result and take less time, use more simple device. (authors)

Adsorption of copper from the sulphate solution of low copper contents using the cationic resin Amberlite IR 120

International Nuclear Information System (INIS)

Jha, Manis Kumar; Nghiem Van Nguyen; Lee, Jae-chun; Jeong, Jinki; Yoo, Jae-Min

2009-01-01

In view of the increasing importance of the waste processing and recycling to meet the strict environmental regulations, the present investigation reports an adsorption process using the cationic exchanger Amberlite IR 120 for the recovery/removal of copper from the synthetic sulphate solution containing copper ≤0.7 mg/mL similar to the CMP waste effluent of electronic industry. Various process parameters, viz. contact time, solution pH, resin dose, and acid concentration of eluant were investigated for the adsorption of copper from the effluents. The 99.99% copper was found to be adsorbed from the sulphate solution containing copper 0.3-0.7 mg/mL of solution (feed pH 5) at A/R ratio 100 and eq. pH 2.5 in contact time 14 min. The mechanism for the adsorption of copper was found to follow Langmuir isotherm and second order rate. From the loaded organic, copper was eluted effectively by 1.8 M sulphuric acid at A/R ratio 25. The raffinate obtained after the recovery copper could be disposed safely without affecting the environment.

Studies on the sorption behaviours of Th(IV) and U(VI) from aqueous sulphate solutions using impregnated resin

International Nuclear Information System (INIS)

Khatab, A.F.; Sheta, M.E.; Mahfouz, M.G.; Tolba, A.A.

2007-01-01

The sorption behaviours of thorium (IV) and uranium (VI) from aqueous sulphate solutions have been studied using n-dodecylamine and tri-n-octylamine (TOA) dissolved in benzene and impregnated onto amberlite XAD-4 (styrene-divinyl benzene copolymer). The sorption behaviours were evaluated as a function of free acidity, salting out effect, ph value, equilibrium time, V/m ratio, initial metal ion concentration, loaded amine concentration and sorption temperature. The equilibrium time for Th(IV) and U(VI) sorption from aqueous sulphate solution was found to be 90 and 60 minutes, respectively. The sorption of Th(IV) was quantitatively at ph range 3.7-4.3 and at 4.3-5.2 for U(VI). The sorption capacity of the impregnated resin was determined by batch method and it was found to be 0.031 and 0.033 mmol/g for Th(IV) and U(VI), respectively. Elution of Th(IV) from thorium-loaded impregnated resin was quantitatively achieved by using 2 mol/l HNO 3 and by using 0.1 mol/l HCl for U(VI)

Synthesis and Characterization of Modified Epoxy Resins by Silicic Acid Tetraethyl Ester and Nano-SiO2

Institute of Scientific and Technical Information of China (English)

李海燕; 张之圣

2004-01-01

A kind of modified epoxy resins was obtained by condensation of epoxy resin with silicic acid tetraethyl ester(TEOS) and nano-SiO2. The reactions were performed with hydrochloric acid as a catalyst at 63 °C.The structure, thermal stability and morphological characteristics of the modified epoxy resins were studied through infrared spectra(FT-IR) analysis, thermogravimetric (TG) analysis and scanning electron microscopy respectively. It has been found from the IR and TG study that modified epoxy resins have greater thermal stability than epoxy resins, and its thermal stability has been improved by the formation of inter-crosslinked network structure. The modified epoxy resins exhibit heterogeneous morphology and heterogeneity increases with more TEOS feeding, which in turn confirms the formation of inter-crosslinked network structure in modified epoxy resins.

Test plan for demonstrating plutonium extraction from 10-L solutions using EIChrom extraction chromatographic resins

International Nuclear Information System (INIS)

Barney, G.S.

1994-01-01

Corrosive plutonium solutions stored in 10-L containers at the Plutonium Finishing Plant must be treated to convert the plutonium to a safe, solid form for storage and to remove the americium so that radiation exposure can be reduced. Extraction chromatographic resins will be tested for separating plutonium from these solutions in the laboratory. Separation parameters will be developed during the testing for large scale processing of the 10-L solutions and solutions of similar composition. Use of chromatographic resins will allow plutonium separation with minimum of chemical addition to the feed and without the need for plutonium valence adjustment. The separated plutonium will be calcined to plutonium oxide by direct solution calcination

Concentrating cesium-137 from seawater using resorcinol-formaldehyde resin for radioecological monitoring

Energy Technology Data Exchange (ETDEWEB)

Egorin, Andrei; Tokar, Eduard; Tutov, Mikhail; Avramenko, Valentin [Institute of Chemistry FEBRAS, Vladivostok (Russian Federation); Far Eastern Federal Univ., Vladivostok (Russian Federation); Palamarchuk, Marina; Marinin, Dmitry [Institute of Chemistry FEBRAS, Vladivostok (Russian Federation)

2017-04-01

A method of preconcentrating cesium-137 from seawater using a resorcinol-formaldehyde resin, which enables one to optimize the ecological monitoring procedure, has been suggested. Studies of sorption of cesium-137 from seawater by resorcinol-formaldehyde resin have been performed, and it has been demonstrated that the cation exchanger is characterized by high selectivity with respect to cesium-137. It was found that the selectivity depended on the temperature of resin solidification and the seawater pH value. The maximal value of the cesium-137 distribution coefficient is equal to 4.1-4.5 x 10{sup 3} cm{sup 3} g{sup -1}. Under dynamic conditions, the ion-exchange resin capacity is 310-910 bed volumes depending on the seawater pH, whereas the efficiency of cesium removal exceeds 95%. The removal of more than 95% of cesium-137 has been attained using 1-3 M solutions of nitric acid: here, the eluate volume was 8-8.4 bed volumes. Application of 3 M solution of nitric acid results in resin degradation with the release of gaseous products.

Raman spectroscopic study of the aging and nitration of actinide processing anion-exchange resins in concentrated nitric acid

International Nuclear Information System (INIS)

Buscher, C. T.; Donohoe, R. J.; Mecklenburg, S. L.; Berg, J. M.; Tait, C. D.; Huchton, K. M.; Morris, D. E.

1999-01-01

Degradation of two types of anion exchange resins, Dowex 11 and Reillex HPQ, from the action of concentrated nitric acid (4 to 12 M) and radiolysis [from depleted uranium as UO 2 2+ nitrate species and 239 Pu as Pu(IV) nitrate species] was followed as a function of time with Raman vibrational spectroscopy. Elevated temperatures (∼50 degree sign C) were used in the absence of actinide metal loading to simulate longer exposures of the resin to a HNO 3 process stream and waste storage conditions. In the absence of actinide loading, only minor changes in the Dowex resin at acid concentrations ≤10 M were observed, while at 12 M acid concentration, the emergence of a Raman peak at 1345 cm-1 indicates the addition of nitro functional groups to the resin. Similar studies with the Reillex resin show it to be more resistant to nitric acid attack at all acid concentrations. Incorporation of weakly radioactive depleted uranium as the UO 2 2+ nitrate species to the ion-exchange sites of Dowex 11 under differing nitric acid concentrations (6 to 12 M) at room temperature showed no Raman evidence of resin degradation or nitration, even after several hundred days of contact. In contrast, Raman spectra for Dowex 11 in the presence of 239 Pu as Pu(IV) nitrate species reveal numerous changes indicating resin alterations, including a new mode at 1345 cm-1 consistent with a Pu(IV)-nitrate catalyzed addition of nitro groups to the resin backbone. (c) 2000 Society for Applied Spectroscopy

Kinetic, equilibrium and thermodynamic studies on sorption of uranium and thorium from aqueous solutions by a selective impregnated resin containing carminic acid

International Nuclear Information System (INIS)

Rahmani-Sani, Abolfazl; Hosseini-Bandegharaei, Ahmad; Hosseini, Seyyed-Hossein; Kharghani, Keivan; Zarei, Hossein; Rastegar, Ayoob

2015-01-01

Highlights: • The objective of the study is to investigate the potential application of a selective EIR for sorption of U(VI) and Th(IV) ions. • The effects of several physiochemical parameters were investigated. • The sorption kinetics and sorption isotherms were used to explain the sorption mechanism. • The thermodynamic studies showed the feasibility of sorption process. • The EIR beads showed a great potential for effective removal of U(VI) and Th(IV) ions. - Abstract: In this work, the removal of uranium and thorium ions from aqueous solutions was studied by solid–liquid extraction using an advantageous extractant-impregnated resin (EIR) prepared by loading carminic acid (CA) onto Amberlite XAD-16 resin beads. Batch sorption experiments using CA/XAD-16 beads for the removal of U(VI) and Th(IV) ions were carried out as a function of several parameters, like equilibration time, metal ion concentration, etc. The equilibrium data obtained from the sorption experiments were adjusted to the Langmuir isotherm model and the calculated maximum sorption capacities in terms of monolayer sorption were in agreement with those obtained from the experiments. The experimental data on the sorption behavior of both metal ions onto the EIR beads fitted well in both Bangham and intra-particle diffusion kinetic models, indicating that the intra-particle diffusion is the rate-controlling step. The thermodynamic studies at different temperatures revealed the feasibility and the spontaneous nature of the sorption process for both uranium and thorium ions

Sorption of Pu(IV) from nitric acid by bifunctional anion-exchange resins

International Nuclear Information System (INIS)

Bartsch, R.A.; Zhang, Z.Y.; Elshani, S.; Zhao, W.; Jarvinen, G.D.; Barr, M.E.; Marsh, S.F.; Chamberlin, R.M.

1999-01-01

Anion exchange is attractive for separating plutonium because the Pu(IV) nitrate complex is very strongly sorbed and few other metal ions form competing anionic nitrate complexes. The major disadvantage of this process has been the unusually slow rate at which the Pu(IV) nitrate complex is sorbed by the resin. The paper summarizes the concept of bifunctional anion-exchange resins, proposed mechanism for Pu(IV) sorption, synthesis of the alkylating agent, calculation of K d values from Pu(IV) sorption results, and conclusions from the study of Pu(IV) sorption from 7M nitric acid by macroporous anion-exchange resins including level of crosslinking, level of alkylation, length of spacer, and bifunctional vs. monofunctional anion-exchange resins

Ion exchange removal of technetium from salt solutions

International Nuclear Information System (INIS)

Walker, D.D.

1983-01-01

Ion exchange methods for removing technetium from waste salt solutions have been investigated by the Savannah River Laboratory (SRL). These experiments have shown: Commercially available anion exchange resins show high selectivity and capacity for technetium. In column runs, 150 column volumes of salt solution were passed through an ion exchange column before 50% 99 Tc breakthrough was reached. The technetium can be eluted from the resin with nitric acid. Reducing resins (containing borohydride) work well in simple hydroxide solutions, but not in simulated salt solutions. A mercarbide resin showed a very high selectivity for Tc, but did not work well in column operation

Removal of Pb2+ from aqueous solutions by a high-efficiency resin

International Nuclear Information System (INIS)

Guo, Hao; Ren, Yongzheng; Sun, Xueliang; Xu, Yadi; Li, Xuemei; Zhang, Tiancheng; Kang, Jianxiong; Liu, Dongqi

2013-01-01

The removal of Pb 2+ from aqueous solution by 732 cation-exchange resin in sodium type (732-CR) has been studied in batch experiments at varying pH (2.0–8.0), Pb 2+ concentration (50–200 mg/L), contact time (5–300 min), temperature (288–308 K) and resin dose (0.125–0.75 g/L). The experimental data show that the ion-exchange process was dependent on pH and temperature, the optimal exchange capacity was found at pH 4.0, and higher temperature was beneficial to lead sorption. Kinetic data indicate that the ion-exchange process followed a pseudo-first order model. The equilibrium exchange capacity could be reached at approximately 4 h, and the maximum sorption capacity of Pb 2+ at pH 4.0 was 396.8 mg/g resin. The equilibrium data were evaluated with Langmuir and Freundlich model, and were best fitted with Langmuir model. The thermodynamic parameters for removal of Pb 2+ indicate that the reaction was spontaneous and endothermic. Additionally, column tests were conducted by using both synthetic solution and effluents from lead battery industry. The regeneration of resin was performed for two sorption-regeneration cycles by 1 M NaOH, and the results show that effective regeneration was achieved by this method.

Usage of methyl ester of tall oil fatty acids and resinic acids as alternative diesel fuel

International Nuclear Information System (INIS)

Keskin, Ali; Yasar, Abdulkadir; Guerue, Metin; Altiparmak, Duran

2010-01-01

In the experimental study, tall oil fatty and resinic acids were investigated as alternative diesel fuels. The fatty acids, obtained by distilling the crude tall oil, were esterified with methanol in order to obtain tall oil methyl ester (biodiesel). Blends of the methyl ester, resinic acids and diesel fuel were prepared for test fuels. Performance and emission tests of the test fuels were carried out in an unmodified direct injection diesel engine on full load conditions. The results showed that the specific fuel consumption (SFC) with the blend fuels did not show a significant change. CO emission and smoke level decreased up to 23.91% and 19.40%, respectively. In general, NO x emissions showed on trend of increasing with the blend fuels (up to 25.42%). CO 2 emissions did not vary with the blend fuels significantly.

Usage of methyl ester of tall oil fatty acids and resinic acids as alternative diesel fuel

Energy Technology Data Exchange (ETDEWEB)

Keskin, Ali; Yasar, Abdulkadir [Tarsus Technical Education Faculty, Mersin University, 33500 Mersin (Turkey); Guerue, Metin [Engineering and Architectural Faculty, Gazi University, 06570 Maltepe, Ankara (Turkey); Altiparmak, Duran [Technical Education Faculty, Gazi University, 06500 Ankara (Turkey)

2010-12-15

In the experimental study, tall oil fatty and resinic acids were investigated as alternative diesel fuels. The fatty acids, obtained by distilling the crude tall oil, were esterified with methanol in order to obtain tall oil methyl ester (biodiesel). Blends of the methyl ester, resinic acids and diesel fuel were prepared for test fuels. Performance and emission tests of the test fuels were carried out in an unmodified direct injection diesel engine on full load conditions. The results showed that the specific fuel consumption (SFC) with the blend fuels did not show a significant change. CO emission and smoke level decreased up to 23.91% and 19.40%, respectively. In general, NO{sub x} emissions showed on trend of increasing with the blend fuels (up to 25.42%). CO{sub 2} emissions did not vary with the blend fuels significantly. (author)

Efficient in situ separation and production of L-lactic acid by Bacillus coagulans using weak basic anion-exchange resin.

Science.gov (United States)

Zhang, Yitong; Qian, Zijun; Liu, Peng; Liu, Lei; Zheng, Zhaojuan; Ouyang, Jia

2018-02-01

To get rid of the dependence on lactic acid neutralizer, a simple and economical approach for efficient in situ separation and production of L-lactic acid was established by Bacillus coagulans using weak basic anion-exchange resin. During ten tested resins, the 335 weak basic anion-exchange resins demonstrated the highest adsorption capacity and selectivity for lactic acid recovery. The adsorption study of the 335 resins for lactic acid confirmed that it is an efficient adsorbent under fermentation condition. Langmuir models gave a good fit to the equilibrium data at 50 °C and the maximum adsorption capacity for lactic acid by 335 resins was about 402 mg/g. Adsorption kinetic experiments showed that pseudo-second-order kinetics model gave a good fit to the adsorption rate. When it was used for in situ fermentation, the yield of L-lactic acid by B. coagulans CC17 was close to traditional fermentation and still maintained at about 82% even after reuse by ten times. These results indicated that in situ separation and production of L-lactic acid using the 335 resins were efficient and feasible. This process could greatly reduce the dosage of neutralizing agent and potentially be used in industry.

Determination of free nitric acid in uranyl nitrate solution

International Nuclear Information System (INIS)

Mayankutty, P.C.; Ravi, S.; Nadkarni, M.N.

1981-01-01

Potentiometric titration of uranyl nitrate solution with sodium hydroxide exhibits two peaks. The first peak characterises the following reaction, UO 2 (C 2 O 4 )+NaOH Na[UO 2 (C 2 O 4 )(OH)]. This reaction, indicating the partial hydrolysis of uranyl oxalate complex, appears to be complete at pH9. If the titration is carried out to this end-point pH, the total alkali consumed can be equated to the sum of uranium content and the free acidity present in the sample volume. Based on this, a method was standardised to determine the free acidity in uranyl nitrate solution. The sample, taken in a solution of potassium oxalate previously adjusted to pH9, is titrated to this pH with standard sodium hydroxide. The free acidity in the sample can be computed by subtracting the alkali reacted with uranium from the total alkali consumed. Analyses of several synthetic samples containing uranium and nitric acid in a wide range of combinations indicate that the free acidity can be accurately determined by this method, if uranium concentration in the sample is known. The results are compared to those obtained by two other widely used methods, viz., (i) titration of pH7 in the presence of neutral potassium oxalate to suppress hydrolysis and (ii) separation of hydrolyzable ions on a cationic resin and alkali titration of the free acid released. The advantages of and the precision obtained with the present method over the above two methods are discussed. (author)

Phenolic cation-exchange resin material for recovery of cesium and strontium. [Patent application

Science.gov (United States)

Ebra, M.A.; Wallace, R.M.

1982-05-05

A phenolic cation exchange resin with a chelating group has been prepared by reacting resorcinol with iminodiacetic acid in the presence of formaldehyde at a molar ratio of about 1:1:6. The material is highly selective for the simultaneous recovery of both cesium and strontium from aqueous alkaline solutions, such as, aqueous alkaline nuclear wate solutions. The organic resins are condensation polymers of resorcinol and formaldehyde with attached chelating groups. The column performance of the resins compares favorably with that of commercially available resins for either cesium or strontium removal. By combining Cs/sup +/ and Sr/sup 2 +/ removal in the same bed, the resins allow significant reduction of the size and complexity of facilities for processing nuclear waste.

In vitro adsorption of oxalic acid and glyoxylic acid onto activated charcoal, resins and hydrous zirconium oxide

NARCIS (Netherlands)

Scholtens, R.; Scholten, J.; de Koning, H. W.; Tijssen, J.; ten Hoopen, H. W.; Olthuis, F. M.; Feijen, J.

1982-01-01

Patients suffering from primary hyperoxaluria show elevated plasma concentrations of oxalic acid and glyoxylic acid. The in vitro adsorption of these compounds into activated charcoal, a series of neutral and ion exchange resins and onto hydrous zirconium oxide has been investigated. Hydrous

Process for the preparation of lactic acid and glyceric acid

Science.gov (United States)

Jackson, James E [Haslett, MI; Miller, Dennis J [Okemos, MI; Marincean, Simona [Dewitt, MI

2008-12-02

Hexose and pentose monosaccharides are degraded to lactic acid and glyceric acid in an aqueous solution in the presence of an excess of a strongly anionic exchange resin, such as AMBERLITE IRN78 and AMBERLITE IRA400. The glyceric acid and lactic acid can be separated from the aqueous solution. Lactic acid and glyceric acid are staple articles of commerce.

Selective Removal of Uranium from the Washing Solution of Uranium-Contaminated Soil

Energy Technology Data Exchange (ETDEWEB)

Kim, Seung Soo; Han, G. S.; Kim, G. N.; Koo, D. S.; Jeong, J. W.; Choi, J. W. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2015-10-15

This study examined selective removal methods of uranium from the waste solution by ion exchange resins or solvent extraction methods to reduce amount of the 2{sup nd} waste. Alamine-336, known as an excellent extraction reagent of uranium from the leaching solution of uranium ore, did not remove uranium from the acidic washing solution of soil. Uranyl ions in the acidic waste solution were sorbed on ampholyte resin with a high sorption efficiency, and desorbed from the resin by a washing with 0.5 M Na{sub 2}CO{sub 3} solution at 60 .deg. C. However, the uranium dissolved in the sulfuric acid solution was not sorbed onto the strong anion exchanger resins. A great amount of uranium-contaminated (U-contaminated) soil had been generated from the decommissioning of a uranium conversion plant. Our group has developed a decontamination process with washing and electrokinetic methods to decrease the amount of waste to be disposed of. However, this process generates a large amount of waste solution containing various metal ions.

Resin-based preparation of HTGR fuels: operation of an engineering-scale uranium loading system

International Nuclear Information System (INIS)

Haas, P.A.

1977-10-01

The fuel particles for recycle of 233 U to High-Temperature Gas-Cooled Reactors are prepared from uranium-loaded carboxylic acid ion exchange resins which are subsequently carbonized, converted, and refabricated. The development and operation of individual items of equipment and of an integrated system are described for the resin-loading part of the process. This engineering-scale system was full scale with respect to a hot demonstration facility, but was operated with natural uranium. The feed uranium, which consisted of uranyl nitrate solution containing excess nitric acid, was loaded by exchange with resin in the hydrogen form. In order to obtain high loadings, the uranyl nitrate must be acid deficient; therefore, nitric acid was extracted by a liquid organic amine which was regenerated to discharge a NaNO 3 or NH 4 NO 3 solution waste. Water was removed from the uranyl nitrate solution by an evaporator that yielded condensate containing less than 0.5 ppM of uranium. The uranium-loaded resin was washed with condensate and dried to a controlled water content via microwave heating. The loading process was controlled via in-line measurements of the pH and density of the uranyl nitrate. The demonstrated capacity was 1 kg of uranium per hour for either batch loading contractors or a continuous column as the resin loading contractor. Fifty-four batch loading runs were made without a single failure of the process outlined in the chemical flowsheet or any evidence of inability to control the conditions dictated by the flowsheet

Investigation of the oxidation states of Pu isotopes in a hydrochloric acid solution

Energy Technology Data Exchange (ETDEWEB)

Lee, M.H. [Nuclear Chemistry Research Division, Korea Atomic Energy Research Institute, P. O. Box 105, Yuseong, Daejeon 305-353 (Korea, Republic of)], E-mail: mhlee@kaeri.re.kr; Kim, J.Y.; Kim, W.H.; Jung, E.C.; Jee, K.Y. [Nuclear Chemistry Research Division, Korea Atomic Energy Research Institute, P. O. Box 105, Yuseong, Daejeon 305-353 (Korea, Republic of)

2008-12-15

The characteristics of the oxidation states of Pu in a hydrochloric acid solution were investigated and the results were applied to a separating of Pu isotopes from IAEA reference soils. The oxidation states of Pu(III) and Pu(IV) were prepared by adding hydroxylamine hydrochloride and sodium nitrite to a Pu stock solution, respectively. Also, the oxidation state of Pu(VI) was adjusted with concentrated HNO{sub 3} and HClO{sub 4}. The stability of the various oxidation states of plutonium in a HCl solution with elapsed time after preparation were found to be in the following order: Pu(III){approx}Pu(VI)>Pu(IV)>Pu(V). The chemical recoveries of Pu(IV) in a 9 M HCl solution with an anion exchange resin were similar to those of Pu(VI). This method for the determination of Pu isotopes with an anion exchange resin in a 9 M HCl medium was applied to IAEA reference soils where the activity concentrations of {sup 239,240}Pu and {sup 238}Pu in IAEA-375 and IAEA-326 were consistent with the reference values reported by the IAEA.

The effect of disinfectant solutions on the hardness of acrylic resin denture teeth.

Science.gov (United States)

Pavarina, A C; Vergani, C E; Machado, A L; Giampaolo, E T; Teraoka, M T

2003-07-01

This investigation studied the effects of disinfectant solutions on the hardness of acrylic resin denture teeth. The occlusal surfaces of 64 resin denture teeth were ground flat with abrasives up to 400-grit silicon carbide paper. Measurements were made after polishing and after the specimens were stored in water at 37 degrees C for 48 h. The specimens were then divided into four groups and immersed in chemical disinfectants (4% chlorhexidine; 1% sodium hypochlorite and sodium perborate) for 10 min. The disinfection methods were performed twice to simulate clinical conditions and hardness measurements were made. Specimens tested as controls were immersed in water during the same disinfection time. Eight specimens were produced for each group. After desinfection procedures, testing of hardness was also performed after the samples were stored at 37 degrees C for 7, 30, 60, 90 and 120 days. Data were analysed using two-way analysis of variance (anova) and Tukey's test at 95% confidence level. According to the results, no significant differences were found between materials and immersion solutions (P > 0.05). However, a continuous decrease in hardness was noticed after ageing (P surfaces of both acrylic resin denture teeth softened upon immersion in water regardless the disinfecting solution.

Electrodeposition properties of modified cational epoxy resin-type photoresist

International Nuclear Information System (INIS)

Yong He; Yunlong Zhang; Feipeng Wu; Miaozhen Li; Erjian Wang

1999-01-01

Multi-component cationic epoxy and acrylic resin system for ED photoresist was used in this work, since they can provide better storage stability for ED emulsion and better physical and chemical properties of deposited film than one-component system. The cationic main resin (AE) was prepared from amine modified epoxy resins and then treated with acetic acid. The amination degree was controlled as required. The synthetic procedure of cationic main resins is described in scheme I. The ED photoresist (AME) is composed of cationic main resin (AE) and nonionic multifunctional acrylic crosslinkers (PETA), in combination with suitable photo-initiator. They can easily be dispersed in deionized water to form a stable ED emulsion. The exposed part of deposited film upon UV irradiation occurs crosslinking to produce an insoluble semi-penetrating network and the unexposed part remains good solubility in the acidic water solution. It is readily utilized for fabrication of fine micropattern. The electrodeposition are carried out on Cu plate at room temperature. To evaluate the electrodeposition properties of ED photoresist (AME), the different influences are examined

Influence of the vacuum resin process, on the ballistic behaviour of lightweight armouring solutions

Science.gov (United States)

Lefebvre, M.; Boussu, F.; Coutellier, D.; Vallee, D.

2012-08-01

The armour of vehicles against conventional threats is mainly composed with steel or aluminium panels. Efficient heavy solutions exist, but the involved industries require new lightweight structures. Moreover, unconventional threats as IEDs (Improvised Explosive Devices) may cause severe damages on these structural and protective panel solutions. Thus, combination of aluminium or steel plates with textile composite structures used as a backing, leads to the mass reduction and better performance under delamination behaviour against these new threats. This paper is a part of a study dealing with the impact behaviour of three warp interlocks weaving structures under Fragment Simulating Projectile (FSP) impact. During this research, several parameters has being studied as the influence of the yarns insertions [1-4], the degradation of the yarns during the weaving process [5-7], and the influence of the resin rate on the ballistic behaviour. The resin rate inside composite materials is dependant on the final application. In ballistic protection, we need to control the resin rate in order to have a deformable structure in order to absorb the maximum of energy. However, with the warp interlocks weaving structure, the yarns insertions induce empty spaces between the yarns where the resin takes place without being evacuated. The resin rate inside the warp interlocks structures is in the most of cases less than 50%, which lead to have brittle and hard material during the impact. Contrary to interlocks structures, the existing protection based on prepreg structure have a high fibres ratio around 88% of weight. That leads to have the best ballistic properties during the impact and good deformability of the structure. The aim of this paper is to evaluate the influence of the resin rate on the ballistic results of the composites materials. For that, we have chosen two kinds of warp interlocks fabrics which were infused with epoxy resin following two processes. The first is a

Resin catalysts and method of preparation

Science.gov (United States)

Smith, L.A. Jr.

1986-12-16

Heat stabilized catalyst compositions are prepared from nuclear sulfonic acid, for example, macroporous crosslinked polyvinyl aromatic compounds containing sulfonic acid groups are neutralized with a metal of Al, Fe, Zn, Cu, Ni, ions or mixtures and alkali, alkaline earth metals or ammonium ions by contacting the resin containing the sulfonic acid with aqueous solutions of the metals salts and alkali, alkaline earth metal or ammonium salts. The catalysts have at least 50% of the sulfonic acid groups neutralized with metal ions and the balance of the sulfonic acid groups neutralized with alkali, alkaline earth ions or ammonium ions.

Fixation of metallic sulfosalicylate complexes on an anionic exchange resin

International Nuclear Information System (INIS)

Cahuzac, S.

1969-06-01

Since sulfosalicylate ions have acid-base properties, sulfosalicylate complexes have an apparent stability which varies with the ph. As a result, the fixation of sulfo-salicylates on an anionic exchange resin depends on the ph of the solution in equilibrium with the resin. This research has been aimed at studying the influence of the ph on the fixation on an anionic exchange resin (Dowex 1 x 4) of sulfosalicylate anions on the one hand, and of metallic sulfosalicylate complexes on the other hand. In the first part of this work, a determination has been made, by frontal analysis of the distribution of sulfosalicylate ions in the resin according to the total sulfosalicylate I concentration in the aqueous solution in equilibrium with the resin. The exchange constants of these ions between the resin and the solution have been calculated. In the second part, a study has been made of the fixation of anionic sulfosalicylate complexes of Fe(III), Al(III), Cr(III), Cu(II), Ni(II), Co(II), Zn(II), Mn(II), Cd(II), Fe(II) and UO 2 2+ . By measuring the partition coefficients of these different elements between the resin and the solution it has been possible to give interpretation for the modes of fixation of the metallic ions, and to calculate their exchange constant between the resin and the solution. The relationship has been established for each metallic element studied, between its partition coefficient, the ph and the total concentration of the complexing agent in solution. Such a relationship makes it possible to predict, for given conditions, the nature of the species in solution and in the resin, as well as the partition coefficient of a metallic, element. Finally, in the third part of the work, use has been made of results obtained previously, to carry out some separations (Ni 2+ - Co 2+ ; Ni 2+ - Co 2+ - Cu 2+ ; UO 2 2+ - Fe 3+ ; UO 2 2+ - Cr 3+ ; UO 2 2+ - Cu 2+ ; UO 2 2+ - Ni 2+ ; UO 2 2+ - Co 2+ ; UO 2 2+ - Mn 2+ and UO 2 2+ - Cd 2+ ), as well as the purification

Inverse-Frontal Chromatography studies on enrichment of Boron-10 using quaternery 4-vinylpyridine-divinylbenzene resin

International Nuclear Information System (INIS)

Bejawada, Venki; Mohapatra, C.; Rao, A.S.; Prasad, K.L.; Murthy, P.K.; Rao, A.K.; Singh, H.P.; Vithal, G.K.; Kumar, Sangita D.

2014-01-01

In order to enrich 10 B, band migration of boric acid-mannitol with hydrochloric acid solution was performed by inverse frontal chromatography on a porous, 25% crosslinked, 38% quaternized 4-vinylpyridine-divinylbenzene resin (py-resin). The work was initiated to replace the existing strong base anion exchange resin type-II (SBA-II) which is used in Boron Enrichment Plant (BEP) of heavy water plant Manuguru. Before its application in BEP, it is mandatory to evaluate py-resin for its performance. The studies showed that maximum of 40% 10 B enrichment observed after 13 m band movement and there was no further improvement, hence profile sampling carried out after 28 m. (author)

Immobilisation of ion exchange resins in cement

International Nuclear Information System (INIS)

Howard, C.G.; Jolliffe, C.B.; Lee, D.J.

1990-02-01

Over the last seven years, Low Oxidation State Metal Ion reagents (LOMI) have been used to decontaminate the 100 MW(e) Steam Generating Heavy Water Ractor (SGHWR) at Winfrith. The use of these reagents has resulted in a dilute ionic solution containing activation products which are produced by corrosion of metallic components in the reactor. It has been demonstrated that the amount of activity in the solution can be reduced using organic ion exchanger resins. These resins consist of a cross linked polystyrene with sulphonic acid or quaternary ammonium function groups and can be successfully immobilised in blended cement systems. The formulation which has been developed is produced from a 9 to 1 blend of ground granulated blast furnace slag (BFS) and ordinary Portland cement (OPC) containing 28% ion exchange resin in the water saturated form. If 6% Microsilica is added to the blended cement the waste loading can be increased to 36 w/o. (author)

Novel bioactive polyester scaffolds prepared from unsaturated resins based on isosorbide and succinic acid

Energy Technology Data Exchange (ETDEWEB)

Śmiga-Matuszowicz, Monika, E-mail: monika.smiga-matuszowicz@polsl.pl [Silesian University of Technology, Department of Physical Chemistry and Technology of Polymers, M. Strzody Street 9, 44-100 Gliwice (Poland); Janicki, Bartosz; Jaszcz, Katarzyna; Łukaszczyk, Jan [Silesian University of Technology, Department of Physical Chemistry and Technology of Polymers, M. Strzody Street 9, 44-100 Gliwice (Poland); Kaczmarek, Marcin [Silesian University of Technology, Department of Biomaterials and Medical Devices Engineering, de Gaulle' a Street 66, 41-800 Zabrze (Poland); Lesiak, Marta; Sieroń, Aleksander L. [Medical University of Silesia, Department of General and Molecular Biology and Genetics, Medyków Street 18, 40-752 Katowice (Poland); Simka, Wojciech [Silesian University of Technology, Department of Chemistry, Inorganic Technology and Fuels, B. Krzywoustego Street 6, 44-100 Gliwice (Poland); Mierzwiński, Maciej; Kusz, Damian [Medical University of Silesia, Department of Orthopedics and Traumatology, Ziołowa Street 45, 40-635 Katowice (Poland)

2014-12-01

In this study new biodegradable materials obtained by crosslinking poly(3-allyloxy-1,2-propylene succinate) (PSAGE) with oligo(isosorbide maleate) (OMIS) and small amount of methyl methacrylate were investigated. The porous scaffolds were obtained in the presence of a foaming system consisted of calcium carbonate/carboxylic acid mixture, creating in situ porous structure during crosslinking of liquid formulations. The maximum crosslinking temperature and setting time, the cured porous materials morphology as well as the effect of their porosity on mechanical properties and hydrolytic degradation process were evaluated. It was found that the kind of carboxylic acid used in the foaming system influenced compressive strength and compressive modulus of porous scaffolds. The MTS cytotoxicity assay was carried out for OMIS using hFOB1.19 cell line. OMIS resin was found to be non-toxic in wide range of concentrations. On the ground of scanning electron microscopy (SEM) observations and energy X-ray dispersive analysis (EDX) it was found that hydroxyapatite (HA) formation at the scaffolds surfaces within short period of soaking in phosphate buffer solution occurs. After 3 h immersion a compact layer of HA was observed at the surface of the samples. The obtained results suggest potential applicability of resulted new porous crosslinked polymeric materials as temporary bone void fillers. - Highlights: • Isosorbide-based resin was used as a component of biodegradable scaffolds. • CAC/carboxylic acid system was proven as facile method to obtain porous scaffolds. • Porous scaffolds displayed the formation of hydroxyapatite at their surfaces.

CHEMICAL COMPOSITIONS OF PINE RESIN, ROSIN AND TURPENTINE OIL FROM WEST JAVA

OpenAIRE

Wiyono Bambang; Tachibana Sanro; Djaban Tinambunan

2006-01-01

This study was conducted to identify chemical composition of merkus pine resin, rosin and turpentine oil. Initially, pine resin was separated into neutral and acidic fractions with an aqueous 4% sodium hydroxide solution. After methylation, the fraction containing turpentine oil and rosin were analyzed by gas chromatography (GC), and gas chromatograph mass spectrometry (GC-MS), respectively. The neutral fraction of pine resin and turpentine oil mainly consisted of a-pinene, D-3-carene and b-p...

Loading ion exchange resins with uranium for HTGR fuel kernels

International Nuclear Information System (INIS)

Notz, K.J.; Greene, C.W.

1976-12-01

Uranium-loaded ion exchange beads provide an excellent starting material in the production of uranium carbide microspheres for nuclear fuel applications. Both strong-acid (sulfonate) and weak-acid (carboxylate) resins can be fully loaded with uranium from a uranyl nitrate solution utilizing either a batch method or a continuous column technique

The resin-in-pulp process and its application to ores from Brosses ''BRS 10''; Le procede resin in pulp et son application aux minerais des Brosses ''BRS 10''

Energy Technology Data Exchange (ETDEWEB)

Kremer, M

1959-03-01

The resin-in-pulp process is a technical variant of the recovery process of uranium in dilute solution by means of ion exchanger resins. An anion resin, XE 123, of a well-defined grain size is placed in direct contact with the pulp produced by sulfuric acid attack on ore with a low uranium content. This process is of particular value in the treatment of pulps that cannot be filtered or decanted, such as those obtained with ore from Brosses. The preparation of the pulp, the elution of the uranium, and its fixation, as well as the various factors encountered in these operations, are discussed. (author) [French] Le procede ''resin in pulp'' est une variante technique du procede de recuperation de l'uranium en solution diluee par les resines echangeuses d'ions. Une resine anionique, la 'XE 123' a granulometrie bien determinee, est mise en contact direct avec la pulpe provenant de l'attaque a l'acide sulfurique d'un minerai d'uranium a faible teneur. Ce procede est particulierement interessant dans le cas de pulpes infiltrables ou indecantables, telles que celles obtenues dans l'attaque du minerai des Brosses. La preparation de la pulpe, la fixation et l'elution de l'uranium, ainsi que les facteurs intervenant dans ces diverses operations sont etudies dans le present rapport. (auteur)

Studies concerning the anion ex-change resins catalyzed esterification of epichlorohydrin with organic acids

Directory of Open Access Journals (Sweden)

E.I. Muresan

2009-09-01

Full Text Available The paper studies the esterification of carboxylic acids with epichlorohydrin over two macroporous strong base anion exchange resins with different polymer matrix. For both resins, the influence of reaction parameters (temperature, catalyst loading, molar ratio on the reaction rate and the yields of the two isomeric esters were investigated.

Impact of pH and application time of meta-phosphoric acid on resin-enamel and resin-dentin bonding.

Science.gov (United States)

Cardenas, A F M; Siqueira, F S F; Bandeca, M C; Costa, S O; Lemos, M V S; Feitora, V P; Reis, A; Loguercio, A D; Gomes, J C

2018-02-01

To evaluate the immediate microshear resin-enamel bond strength (μSBS) and the immediate and 6-month microtensile bond strength (μTBS) and nanoleakage (NL) of the adhesive interface performed by different pHs of 40% meta-phosphoric acid (MPA) were compared with conventional 37% ortho-phosphoric acid (OPA) under different application times. Additionally, the enamel etching patterns were evaluated and the chemical/morphological changes induced by these differents groups were evaluated. One hundred and ninety-eight extracted human molars were randomly assigned into experimental groups according to the combination of independent variables: Acid [37% ortho-phosphoric acid (OPA), 40% meta-phosphoric acid (MPA) at pHs of: 0.5, 1 and 2] and Application Time [7, 15 and 30s]. Enamel-bond specimens were prepared and tested under μSBS. Resin-dentin beams were tested under μTBS tested immediately or after 6-months of water storage. Nanoleakage was evaluated using bonded-beams of each tooth/time-period. Enamel etching pattern and chemical and ultra-morphology analyses were also performed. The μSBS (MPa) data were subjected to a two-way repeated measures ANOVA (Acid vs. Application time). For μTBS, Acid vs application time vs storage time data were subjected to three-way ANOVA and Tukey's test (α = 0.05). MPA pH 0.5 showed μTBS similar to OPA, independently of the application time on enamel (p>0.05) or dentin (p>0.05). OPA provided higher nanoleakage values than MPA (p = 0.003). Significant decreases in TBS and increases in NL were only observed for OPA after 6 months (p = 0.001). An increase in the application time resulted in a more pronounced etching pattern for MPA. Chemical analysis showed that dentin demineralized by MPA depicted peaks of brushite and octacalcium phosphate. MPA exposed less collagen than OPA. However, optimal results for MPA were dependent on pH/application time. The use of 40% meta-phosphoric acid with a pH of 0.5 is an alternative acid

Evaluation and improvement of gamma-ray stability of chelating resins containing oxy-acid groups of phosphorus

International Nuclear Information System (INIS)

Jyo, Akinori; Yamabe, Kazunori; Shuto, Taketomi

1998-01-01

Chelating resins containing oxy-acid groups of phosphorus, such as phosphonic and phosphoric acid groups have been studied from the point of view of solvent extraction processes for the separation of nuclear fuel elements as well as of fission product ones. The present work was planned to evaluate the effect of gamma-ray on properties of the resins and to obtain directional information for design of the resins having high stability to gamma-ray. It was clarified that gamma-ray stability of the resins is not high; tolerance limit is ca. 2.3x10 3 C/kg. The present work also clarified that polymers crosslinked with divinylbenzene have much higher gamma-ray stability than ones crosslinked with dimetacrylate esters of oligo (ethylene glycol)s. (J.P.N.)

Diclofenac removal in urine using strong-base anion exchange polymer resins.

Science.gov (United States)

Landry, Kelly A; Boyer, Treavor H

2013-11-01

One of the major sources of pharmaceuticals in the environment is wastewater effluent of which human urine contributes the majority of pharmaceuticals. Urine source separation has the potential to isolate pharmaceuticals at a higher concentration for efficient removal as well as produce a nutrient byproduct. This research investigated the efficacy of using strong-base anion exchange polymer resins to remove the widely detected and abundant pharmaceutical, diclofenac, from synthetic human urine under fresh and ureolyzed conditions. The majority of experiments were conducted using a strong-base, macroporous, polystyrene resin (Purolite A520E). Ion-exchange followed a two-step removal rate with rapid removal in 1 h and equilibrium removal in 24 h. Diclofenac removal was >90% at a resin dose of 8 mL/L in both fresh and ureolyzed urine. Sorption of diclofenac onto A520E resin was concurrent with desorption of an equivalent amount of chloride, which indicates the ion-exchange mechanism is occurring. The presence of competing ions such as phosphate and citrate did not significantly impact diclofenac removal. Comparisons of three polystyrene resins (A520E, Dowex 22, Dowex Marathon 11) as well as one polyacrylic resin (IRA958) were conducted to determine the major interactions between anion exchange resin and diclofenac. The results showed that polystyrene resins provide the highest level of diclofenac removal due to electrostatic interactions between quaternary ammonium functional groups of resin and carboxylic acid of diclofenac and non-electrostatic interactions between resin matrix and benzene rings of diclofenac. Diclofenac was effectively desorbed from A520E resin using a regeneration solution that contained 4.5% (m/m) NaCl in an equal-volume mixture of methanol and water. The greater regeneration efficiency of the NaCl/methanol-water mixture over the aqueous NaCl solution supports the importance of non-electrostatic interactions between resin matrix and benzene rings

Recovery of gold with ion exchange resin from leaching solution by acidothioureation. Ion kokan jushiho ni yoru ryusan sansei chio nyoso kinshinshutsueki kara no kin no kaishu ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Nakahiro, Y.; Ninae, M.; Kusaka, E.; Wakamatsu, T. (Kyoto University, Kyoto (Japan). Faculty of Engineering); Horio, Y. (Yamaha Co. Ltd., Tokyo (Japan))

1991-12-25

Recovery of gold with ion exchange resin from leaching solution by acidothioureation, and elution of gold from ion exchange resin with gold were studied experimentally. As the result of batch adsorption experiments of Au(TU){sub 2}{sup +} into various kinds of ion exchange resins, strong acidic cation exchange resin was most suitable, and gold was fully adsorbed into such resin in the pH range from 1.2 to 2.0 without any effects of thiourea in the leaching solution on adsorption of gold. As the result of batch elution experiments in various kinds of eluates, copper was eluted in HNO{sub 3}(1 N) + H{sub 2}O{sub 2}(1wt%) elute, both iron and zinc in NH{sub 4}NO{sub 3}(0.5 M) elute, and gold in Na{sub 2}S{sub 2} O{sub 3}(0.05 M) elute resulting in the recovery of gold. As the result of column elution experiments, Amberlite 200C was most effective among some ion exchangers used for recovery of Au(CS(NH{sub 2}){sub 2}){sub 2}{sup +}. 16 refs., 15 figs.

Influence of the vacuum resin process, on the ballistic behaviour of lightweight armouring solutions

Directory of Open Access Journals (Sweden)

Coutellier D.

2012-08-01

Full Text Available The armour of vehicles against conventional threats is mainly composed with steel or aluminium panels. Efficient heavy solutions exist, but the involved industries require new lightweight structures. Moreover, unconventional threats as IEDs (Improvised Explosive Devices may cause severe damages on these structural and protective panel solutions. Thus, combination of aluminium or steel plates with textile composite structures used as a backing, leads to the mass reduction and better performance under delamination behaviour against these new threats. This paper is a part of a study dealing with the impact behaviour of three warp interlocks weaving structures under Fragment Simulating Projectile (FSP impact. During this research, several parameters has being studied as the influence of the yarns insertions [1–4], the degradation of the yarns during the weaving process [5–7], and the influence of the resin rate on the ballistic behaviour. The resin rate inside composite materials is dependant on the final application. In ballistic protection, we need to control the resin rate in order to have a deformable structure in order to absorb the maximum of energy. However, with the warp interlocks weaving structure, the yarns insertions induce empty spaces between the yarns where the resin takes place without being evacuated. The resin rate inside the warp interlocks structures is in the most of cases less than 50%, which lead to have brittle and hard material during the impact. Contrary to interlocks structures, the existing protection based on prepreg structure have a high fibres ratio around 88% of weight. That leads to have the best ballistic properties during the impact and good deformability of the structure. The aim of this paper is to evaluate the influence of the resin rate on the ballistic results of the composites materials. For that, we have chosen two kinds of warp interlocks fabrics which were infused with epoxy resin following two

Separation and recovery of uranium ore by chlorinating, chelate resin and molten salt treatment

International Nuclear Information System (INIS)

Taki, Tomohiro

2000-12-01

Three fundamental researches of separation and recovery of uranium from uranium ore are reported in this paper. Three methods used the chloride pyrometallurgy, sodium containing molten salts and chelate resin. When uranium ore is mixed with activated carbon and reacted for one hour under the mixed gas of chlorine and oxygen at 950 C, more than 90% uranium volatilized and vaporization of aluminum, silicone and phosphorus were controlled. The best activated carbon was brown coal because it was able to control the large range of oxygen concentration. By blowing oxygen into the molten sodium hydroxide, the elution rate of uranium attained to about 95% and a few percent of uranium was remained in the residue. On the uranium ore of unconformity-related uranium deposits, a separation method of uranium, molybdenum, nickel and phosphorus from the sulfuric acid elusion solution with U, Ni, As, Mo, Fe and Al was developed. Methylene phosphonic acid type chelate resin (RCSP) adsorbed Mo and U, and then 100 % Mo was eluted by sodium acetate solution and about 100% U by sodium carbonate solution. Ni and As in the passing solution were recovered by imino-diacetic acid type chelate resin and iron hydroxide, respectively. (S.Y.)

SHALLOW SHELL RESIN VERSUS TRADITIONAL RESIN: A CASE STUDY FOR Cu(II REMOVAL

Directory of Open Access Journals (Sweden)

Özgür Arar

2016-10-01

Full Text Available A comparative study on Cu2+ removal by shallow shell resin (Purolite SST 60 and traditional strongly acidic cation exchange resin (Purolite PFC 100 was performed. Batch experiments were carried out as a function of  resin  dosage and  solution pH and contact time. Ion exchange reaction showed a pH depended feature.  Maximum removal of Cu2+ achieved  pH  from 2 to 5. Sorption isothermal data is well interpreted by the Langmuir equation. Additionally, kinetic experiments showed that the pseudo first-order model was suitable for such resins. The regeneration performance of shallow shell technology (SST resin is better than PFC 100.  A solution of 2M H2SO4 performed well in regenerationof SST 60 resin. On the other han maximum regeneration reached 80% for PFC 100 resin.Özet: Bu çalışmada, klasik iyon değiştirici reçine (Purolite PFC 100 ve  sığ kabuk  reçine (Purolite SST 60  ile Cu2+ giderilmesi incelenmiştir. Yapılan kesikli çalışmalarla Cu2+ giderilmesine, reçine miktarı, çözelti pH`ı ve temas süresinin etkisi incelenmiştir. Çözelti pH`ının 2 ile 5 arasında olduğu durumda Cu2+ iyonları tamamen giderilmiştir. Denge çalışmalarında elde edilen sonuçlar Langmuir izoterm modeline daha uygun olmuştur. Kinetik çalışmalarda elde edilen sonuçlar yalancı birinci mertebe kinetik modeline uygunluk göstermişir. SST 60 reçinesinin rejenerasyon verimi PFC 100 reçinesinden daha yüksektir. 2M H2SO4 ile SST 60 reçinesi tamamen rejenere edilmiştir.

Separation of hafnium from zirconium in sulfuric acid solutions using pressurized ion exchange

International Nuclear Information System (INIS)

Hurst, F.J.

1981-01-01

High-resolution pressurized ion exchange has been used successfully to study and separate hafnium and zirconium sulfate complexes by chromatographic elution from Dowex 50W-X8 (15 to 25 μm) resin with sulfuric acid solutions. Techniques were developed to continuously monitor the column effluents for zirconium and hafnium by reaction with fluorometric and colorimetric reagents. Since neither reagent was specific for either metal ion, peak patterns were initially identified by using the stable isotopes 90 Zr and 180 Hf as fingerprints of their elution position. Distribution ratios for both zirconium and hafnium decrease as the inverse fourth power of the sulfuric acid concentration below 2N and as the inverse second power at higher acid concentration. The hafnium-to-zirconium separation factor is approximately constant (approx. 8) over the 0.5 to 3N range. Under certain conditions, an unseparated fraction was observed that was not retained by the resin. The amount of this fraction which is thought to be a polymeric hydrolysis product appears to be a function of metal and sulfuric acid concentrations. Conditions are being sought to give the highest zirconium concentration and the lowest acid concentration that can be used as a feed material for commercial scale-up in the continuous annular chromatographic (CAC) unit without formation of the polymer

Preparation of minor actinides targets or blankets by the means of Ionic Exchange Resin

Energy Technology Data Exchange (ETDEWEB)

Picart, S.; Mokhtari, H.; Ramiere, I.; Jobelin, I. [CEA, Nuclear Energy Division, RadioChemistry and Process Department, Actinides Chemistry Laboratory, BP17171, Bagnols-sur-Ceze, 30207 (France)

2009-06-15

The objective of our R and D work is the elaboration by the use of ionic exchange resin of minor actinide precursors for target or blanket dedicated to their transmutation in sodium fast reactor. From the beginning, the resin process called WAR (acronym of Weak Acid Resin) was developed in the 70's at the ORNL for the making of uranium carbide kernels for the high temperature gas reactor [1] [2]. By now, our aim is to extend this concept to the manufacturing of minor actinides oxide mixed with uranium oxides [3]. More precisely, this process can be divided in two major steps: the loading of the resin and the thermal treatment of the fully loaded resin driving either to oxide or carbide phases depending on the gas atmosphere. The difficulty stems from the preparation of the loading solutions which must fulfill precise conditions of pH in presence of actinides cations prone to hydrolysis. Furthermore, the proportions of uranium and minor actinides in solutions must be adjusted to fit the right ratio in the solid. The study presented here will then focus on the experiments and tests which enable us to optimize the fixing of minor actinides on ionic exchange resin and their carbonization in oxide. [1] G. W. Weber, R. L. Beatty et V. J. Tennery, Nuclear Technology, 35, 217-226, (1977), 'Processing and composition control of weak-acid-resin derived fuel microspheres'. [2] K. J. Notz, P. A. Haas, J. H. Shaffer, Radiochimica Acta, 25, 153-160, (1978). 'The preparation of HTGR Fissile Fuel Kernels by Uranium Loading of Ion Exchange Resin'. [3] S. Picart, H. Mokhtari, I. Ramiere, 'Plutonium Futures, The Science 2008', 7-11 july 2008, Dijon, France. 'Modelling of the ionic Exchange between a weak acid resin in its ammonium form and a minor actinide'. (authors)

Separation of rare earths from solutions of phosphoric acid

International Nuclear Information System (INIS)

Jones, E.A.

1977-01-01

Rare earths are separated from 6M phosphoric acid by adsorption onto cation resin BIORAD AG50W-X8. The phosphoric acid is then washed from the column, and the rare earths are eluted with 4M hydrochloric acid

Treatment of Soil Decontamination Solution by the Cs{sup +} Ion Selective Ion Exchange Resin

Energy Technology Data Exchange (ETDEWEB)

Won, Hui Jun; Kim, Gye Nam; Jung, Chung Hun; Oh, Won Zin [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

2005-07-01

Occasionally, radioactively contaminated soils have been excavated and stored at the temporary storage facility. Cesium as a radionuclide is one of the most toxic elements and it has a long half decay life. During the operation of nuclear facility, soils near the facility would be contaminated with radioactive cesium and it will cause the deleterious effect to human body and environment. In this study, Cs{sup +} ion selective ion exchange resin was prepared by changing the functional group of commercial anion exchange resin for a ferrocyanide ion. Ion exchange capability of using the soil decontamination solution was investigated. We also performed the feasibility test of recycling the spent Cs ion selective ion exchange resin.

Distribution of iron during full loading of amberlite IRC-72 resin with uranium from nitrate solutions at 300C

International Nuclear Information System (INIS)

Shaffer, J.H.; Greene, C.W.

1979-01-01

The integrity of resin-based fuel kernels used in the fabrication of fuel elements for a high-temperature gas-cooled reactor will depend, in part, on the concentration of iron incorporated in the resin particles during their loading with uranium. Consequently, assessment of chemical specifications for iron as an impurity in uranyl nitrate solution should be based on its distribution during the resin loading operation. For this purpose, the behavior of iron, as an impurity in uranyl nitrate solutions, was investigated under equilibrium conditions at 30 0 C during full loading of Amberlite IRC-72 cation exchange reaction were derived from calculations based on complex coordination of ferric ion with the resin over the nitrate ion concentration range of approx. 0.5 to 2 N

Photobleachable Diazonium Salt-Phenolic Resin Two-Layer Resist System

Science.gov (United States)

Uchino, Shou-ichi; Iwayanagi, Takao; Hashimoto, Michiaki

1988-01-01

This article describes a new negative two-layer photoresist system formed by a simple, successive spin-coating method. An aqueous acetic acid solution of diazonium salt and poly(N-vinylpyrrolidone) is deposited so as to contact a phenolic resin film spin-coated on a silicon wafer. The diazonium salt diffuses into the phenolic resin layer after standing for several minutes. The residual solution on the phenolic resin film doped with diazonium salt is spun to form the diazonium salt-poly(N-vinylpyrrolidone) top layer. This forms a uniform two-layer resist without phase separation or striation. Upon UV exposure, the diazonium salt in the top layer bleaches to act as a CEL dye, while the diazonium salt in the bottom layer decomposes to cause insolubilization. Half μm line-and-space patterns are obtained with an i-line stepper using 4-diazo-N,N-dimethylaniline chloride zinc chloride double salt as the diazonium salt and a cresol novolac resin for the bottom polymer layer. The resist formation processes, insolubilization mechanism, and the resolution capability of the new two-layer resist are discussed.

Studies on indigenous ion exchange resins: alkali metal ions-hydrogen ion exchange equilibria

International Nuclear Information System (INIS)

Shankar, S.; Kumar, Surender; Venkataramani, B.

2001-01-01

With a view to select a suitable ion exchange resin for the removal of radionuclides (such as cesium, strontium etc.) from low level radioactive effluents, alkali metal ion -H' exchanges on nine indigenous gel- and macroporous-type and nuclear grade resins have been studied at a total ionic strength of 0.1 mol dm .3 (in the case ofCs' -H' exchange it was 0.05 mol dm .3 ). The expected theoretical capacities were not attained by all the resins for the alkali metal ions. The water content (moles/equiv.) of the fully swollen resins for different alkali metal ionic forms do not follow the usual sequence of greater the tendency of the cation to hydrate the higher the water uptake, but a reverse trend. The ion exchange isotherms (plots of equivalent fractions of the ion in resin phase, N M1 to that in solution, N M ) were not satisfactory and sorption of cations, for most of the resins, was possible only when the acidity of the solution was lowered. The variations of the selectivity coefficient, K, with N M show that the resins are highly cross linked and the selectivity sequence: Cs + >K + >Na + >Li + , obtained for all the resins indicate that hydrated ions were involved in the exchange process. However, the increase in the selectivity was not accompanied by the release of water, but unusual uptake of water, during the exchange process. The characteristics of macroporous resins were not significantly different from those of the gel-type resins. The results are discussed in terms of heterogeneity in the polymer net work, improper sulphonation process resulting in the formation of functional groups at inaccessible sites with weak acidic character and the overall lack of control in the preparation of different resins. (author)

Solvent Extraction of Tungsten(VI) from Moderate Hydrochloric Acid Solutions with LIX 63

Energy Technology Data Exchange (ETDEWEB)

Truong, Hoai Thanh; Lee, Man Seung [Mokpo National University, Jeollanamdo (Korea, Republic of); Kim, Yong Hwan [Incheon Technology Service Centre, Incheon (Korea, Republic of)

2017-06-15

The solvent extraction of tungsten(VI) from hydrochloric acid solutions using 5,8-diethyl-7-hydroxydodecan-6-one oxime (LIX 63) was analyzed in solutions having an initial pH range from 2 to 5, by varying the concentration of metal and extractant. In our experimental range, the cationic exchange reaction as well as the solvation reaction occurred simultaneously. The cation exchange reaction was identified by applying a slope analysis method to the extraction data. The existence of cationic tungsten(VI) species was confirmed by ion exchange experiments with Diphonix resin at pH 3. Further study is needed to identify the nature of this tungsten cationic species.

The removal of toxic metals from liquid effluents by ion exchange resins. Part V: Nickel(II/H+/Dowex C400

Directory of Open Access Journals (Sweden)

Francisco José Alguacil

2017-11-01

Full Text Available The cationic exchange resin Dowex C400 was used to remove nickel(II from aqueous solutions of different pH values and under various experimental conditions: stirring speed of the aqueous solution/resin system, temperature, resin dosage and aqueous ionic strength. The selectivity of the resin was investigated against the presence of various metals in the aqueous solution, and the removal of nickel(II from aqueous solutions was also compared with results obtained using multiwalled carbon nanotubes or functionalized (carboxylic groups multiwalled carbon nanotubes as adsorbents. According to batch experimental data, best fit of the results is obtained with the Freundlich model, whereas the ion exchange process is best explained by the pseudo-first order model. Experimental data fit well to the moving boundary controlled model. Elution of the nickel(II loaded onto Dowex C400 resin is fully possible using acidic solutions.

Extraction and Separation of Uranium (VI) and Thorium (IV) Using Tri-n-dodecylamine Impregnated Resins

International Nuclear Information System (INIS)

Metwally, E.; Saleh, A.Sh.; El-Naggar, H.A.

2005-01-01

Extraction of U(VI) and Th(IV) from chloride and nitrate solutions with tri-n- dodecylamine impregnated on Amberlite XAD4, was investigated. The distribution of U(VI) and Th(IV) was studied at different concentrations of acid, salting-out agent, extractant, aqueous metal ion and other parameters. Absorption spectral studies have been investigated for uranium species in both aqueous HCl solution and the resin phase. From these studies, it is suggested that the tetrachloro complex of U(VI) is formed in the extraction of uranium (VI) from hydrochloric acid solutions by TDA impregnated resin. Stripping of the extracted U(VI) and Th(IV) was assayed with HCl and HNO 3 . Finally, the separation of uranium from thorium and fission products in HCl media was achieved

Cleanup of TMI-2 demineralizer resins

International Nuclear Information System (INIS)

Bond, W.D.; King, L.J.; Knauer, J.B.; Hofstetter, K.J.; Thompson, J.D.

1985-01-01

Radiocesium is being removed from Demineralizers A and B (DA and DB by a process that was developed from laboratory tests on small samples of resin from the demineralizers. The process was designed to elute the radiocesium from the demineralizer resins and then to resorb it onto the zeolite ion exchangers contained in the Submerged Demineralizer System (SDS). The process was also required to limit the maximum cesium activities in the resin eluates (SDS feeds) so that the radiation field surrounding the pipelines would not be excessive. The process consists of 17 stages of batch elution. In the initial stage, the resin is contacted with 0.18 M boric acid. Subsequent stages subject the resin to increasing concentrations of sodium in NaH 2 BO 3 -H 3 BO 3 solution (total B = 0.35 M) and then 1 M sodium hydroxide in the final stages. Results on the performance of the process in the cleanup of the demineralizers at TMI-2 are compared to those obtained from laboratory tests with small samples of the DA and DB resins. To date, 15 stages of batch elution have been completed on the demineralizers at TMI-2 which resulted in the removal of about 750 Ci of radiocesium from DA and about 3300 Ci from DB

Aminolysis of resin-bound N-nosylaziridine-2-carboxylic acids

DEFF Research Database (Denmark)

Olsen, Christian A; Christensen, Caspar; Nielsen, Birgitte

2006-01-01

[Structure: see text] Solid-phase synthesis is a rapidly developing area of organic chemistry, of particular importance for medicinal chemistry and chemical biology. Aziridines have previously only rarely been applied in solid-phase synthesis. In the present work, aminolysis of resin-bound, sprin......-loaded N-nitrobenzenesulfonyl-activated aziridine-2-carboxylic acids has been optimized and employed in the synthesis of a number of open-chain and heterocyclic scaffolds, including enantiopure products....

Behaviour of Type 316 steel in acidic sulphate solutions at 300-3500C

International Nuclear Information System (INIS)

Newman, J.F.

1987-11-01

Most cation resin beds in service in CEGB power stations, and particularly those in AGR stations, are regenerated with sulphuric acid. Slippage results in trace levels of sulphate passing into the boilers. Previous work has shown that in once-through boilers, feedwater containing 2 μg kg -1 of sulphate could concentrate at localized dry-out sites to form solutions having from 0.1 to 7 wt% of solute. It has been shown also that if the sulphate was present in an acidic solution and it were to be in contact with Type 316 austentitic superheater steel, then intergranular corrosion and intergranular cracking could occur. Previous data, including some unreported results, are tabulated and discussed. The current work had two main objectives. The first was to extend the previous investigations to examine a wider range of acidic sulphate concentrations (as indicated by calculations on the concentration of solute in feedwater), the influence of environment pH, and the effect of sensitization of specimens. The second objective was primarily concerned with elucidating the causes of scatter in the results. This involved examining the influence of electrode potential, the ageing characteristics of the environment, and the method of applying stress to the specimens. (author)

Purification of degraded TBP solvent using macroreticular anion exchange resin

International Nuclear Information System (INIS)

Kartha, P.K.S.; Kutty, P.V.E.; Janaradanan, C.; Ramanujam, A.; Dhumwad, R.K.

1989-01-01

Tri-n-butyl phosphate (TBP) diluted with a suitable diluent is commonly used for solvent extraction in Purex process for the recovery of uranium and plutonium from irradiated nuclear fuels. This solvent gets degraded due to various factors, the main degradation product being dibutyl phosphoric acid (HDBP). A solvent cleanup step is generally incorporated in the process for removing the degradation products from the used solvent. A liquid-liquid cleanup system using sodium carbonate or sodium hydroxide solution is routinely used. Considering certain advantages, like the possibility of loading the resin almost to saturation capacity and the subsequent disposal of the spent resin by incineration and the feasibility of adopting it to the process, a liquid-solid system has been tried as an alternate method, employing various available macroreticular anion exchange resins in OH - form for the sorption of HDBP from TBP. After standardizing the various conditions for the satisfactory removal of HDBP from TBP using synthetic mixtures, resins were tested with process solvent in batch contacts. The parameters studied were (1) capacity of different resins for HDBP sorption (2) influence of acidity, uranium and HDBP on the sorption behaviour of the latter (3) removal of fission products from the solvent by the resin and (4) regeneration and recycling of the resin. (author). 2 figs., 13 tabs., 17 refs

Oxidative degradation of low and intermediate level Radioactive organic wastes 2. Acid decomposition on spent Ion-Exchange resins

Energy Technology Data Exchange (ETDEWEB)

Ghattas, N K; Eskander, S B [Radioisotope dept., atomic energy authority, (Egypt)

1995-10-01

The present work provides a simplified, effective and economic method for the chemical decomposition of radioactively contaminated solid organic waste, especially spent ion - exchange resins. The goal is to achieve volume reduction and to avoid technical problems encountered in processes used for similar purposes (incineration, pyrolysis). Factors efficiency and kinetics of the oxidation of the ion exchange resins in acid medium using hydrogen peroxide as oxidant, namely, duration of treatment and the acid to resin ratio were studied systematically on a laboratory scale. Moreover the percent composition of the off-gas evolved during the decomposition process was analysed. 3 figs., 5 tabs.

Oxidative degradation of low and intermediate level Radioactive organic wastes 2. Acid decomposition on spent Ion-Exchange resins

International Nuclear Information System (INIS)

Ghattas, N.K.; Eskander, S.B.

1995-01-01

The present work provides a simplified, effective and economic method for the chemical decomposition of radioactively contaminated solid organic waste, especially spent ion - exchange resins. The goal is to achieve volume reduction and to avoid technical problems encountered in processes used for similar purposes (incineration, pyrolysis). Factors efficiency and kinetics of the oxidation of the ion exchange resins in acid medium using hydrogen peroxide as oxidant, namely, duration of treatment and the acid to resin ratio were studied systematically on a laboratory scale. Moreover the percent composition of the off-gas evolved during the decomposition process was analysed. 3 figs., 5 tabs

Affinity purification of the voltage-sensitive sodium channel from electroplax with resins selective for sialic acid

Energy Technology Data Exchange (ETDEWEB)

James, W.M.; Emerick, M.C.; Agnew, W.S. (Yale Univ. School of medicine, New Haven, CT (USA))

1989-07-11

The voltage-sensitive sodium channel present in the eel (Electrophorus electricus) has an unusually high content of sialic acid, including {alpha}-(2{yields}8)-linked polysialic acid, not found in other electroplax membrane glycopeptides. Lectins from Limax flavus (LFA) and wheat germ (WGA) proved the most effective of 11 lectin resins tried. The most selective resin was prepared from IgM antibodies against Neisseria meningitidis {alpha}-(2{yields}8)-polysialic acid which were affinity purified and coupled to Sepharose 4B. The sodium channel was found to bind to WGA, LFA, and IgM resins and was readily eluted with the appropriate soluble carbohydrates. Experiments with LFA and IgM resins demonstrated binding and unbinding rates and displacement kinetics, which suggest highly specific binding at multiple sites on the sodium channel protein. In preparative-scale purification of protein previously fractionated by anion-exchange chromatography, without stabilizing TTX, high yields were reproducibly obtained. Further, when detergent extracts were prepared from electroplax membranes fractionated by low-speed sedimentation, a single step over the IgM resin provided a 70-fold purification, yielding specific activities of 3,200 pmol of ({sup 3}H)TTX-binding sites/mg of protein and a single polypeptide of {approximately}285,000 Da on SDS-acrylamide gels. No small peptides were observed after this 5-h isolation. The authors describe a cation-dependent stabilization with millimolar levels of monovalent and micromolar levels of divalent species.

Inverse break-through investigation on uranium isotope separation in the system Fe(III) water-glycerine solution-U(IV) cathionic resin

International Nuclear Information System (INIS)

Murgulescu, Sanda; Calusaru, A.

1977-01-01

When a solution containing ferric ions passes on cationic resin in U(IV) form, the substitution of uranium by iron is preceded by oxydation of U(IV) to U(VI). During the contact of U(VI) in solution with U(IV) in resin, an exchange reaction occurs, in which 235 U is slightly concentrated in solution and 238 U in resin phase. Since increase of temperature accelerates the exchange reaction, the apparent thermodynamic values of the exchange reaction were calculated, by taking into account the variation of the apparent equilibrium constant as a function of the reciprocal value of the temperature. The corresponding thermodynamic values in both pure aqueous and water-glycerine solution are: ΔH 0 =6.45 cal.mol -1 and ΔS 0 =21.6x10 -3 cal. 0 K -1 . The use of glycerine containing solutions offers the important advantage to increase the stability versus hydrolysis of the ferric ions even at higher temperature

Studies on the Use of Gamma Radiation-Induced for Preparation of Some Modified Resins for the Separation of Some Metal Ions

International Nuclear Information System (INIS)

Abo-Zahra, S.F.

2012-01-01

The work carried out in the present thesis is based on preparation, characterization and applications of some modified resins such as: poly(acrylamide)/poly(maleic acid) P(AAm)/P(MA) interpolymer complex (resin), poly(acrylamide-acrylic acid-amidoxime) P(AAm-AA-AO) resin and poly(hydroxamic acid) P(HA) resin. Poly(acrylamide)/poly(maleic acid) P(AAm)/P(MA) interpolymer complex (resin) was prepared by template polymerization of maleic acid (MA) monomer on poly(acrylamide) P(AAm) hydrogel as a template polymer in the presence of N,N'-methylenebisacrylamide (NMBA) as a crosslinker using gamma radiation-induced technique. Poly(acrylamide-acrylic acid-amidoxime) P(AAm-AA-AO) resin was prepared by template polymerization of acrylic acid (AA) and acrylonitrile (AN) monomers on P(AAm) hydrogel as a template polymer in the presence of NMBA as a crosslinker using gamma radiation-induced technique. The conversion of nitrile group to amidoxime one was carried out by the treatment of the prepared resin with an alkaline solution of hydroxylamine. Poly(hydroxamic acid) P(HA) resin was prepared from the reaction of the corresponding water-soluble P(AAm) previously prepared by gamma radiation-induced with hydroxylamine hydrochloride in an alkaline medium. The functional groups on the prepared polymeric resins were confirmed by using Fourier transform infrared (FTIR) spectra. Thermogravimetric analysis (TGA), differential scanning calorimetry (DSC) measurements, scanning electron microscopy (SEM) and electron spin resonance (ESR) measurements were performed to evaluate the properties of the prepared polymeric resins, free or complexed with metal ions such as Cu 2+ metal ions.

Thermoanalytical Study and Kinetics of New 8-Hydroxyquinoline 5-sulphonic Acid-Oxamide-Formaldehyde Terpolymer Resins

Directory of Open Access Journals (Sweden)

Rajesh N. Singru

2009-01-01

Full Text Available The terpolymer resins (8-HQ5-SAOF have been synthesized by the condensation of 8-hydroxyquinoline 5-sulphonic acid (8-HQ5-SA and oxamide (O with formaldehyde (F in the presence of acid catalyst and using varied molar proportion of the reacting monomers. The synthesized terpolymer resins have been characterized by different physico-chemical techniques. Thermogravimetric analysis of all terpolymer resins in present study have been carried out by non-isothermal thermogravimetric analysis technique in which sample is subjected to condition of continuous increase in temperature at linear rate. Thermal study of the resins was carried out to determine their mode of decomposition and relative thermal stabilities. Thermal decomposition curves were studied carefully with minute details. The Freeman-Carroll and Sharp-Wentworth methods have been used in the present investigation to calculate thermal activation energy and different kinetic parameter of the terpolymer resins. Thermal activation energy (Ea calculated with above two mentioned methods are in close agreement. The advantage of Freeman-Carroll method is to calculate both the order of reaction (n and energy of activation in one single stage by keeping heating rate constant. By using data of thermogravimetric analysis, various thermodynamic parameters like frequency factor (Z, entropy change (Δ S, free energy change (Δ F and apparent entropy (S* have been determined using Freeman-Carroll method.

Low pressure process for continuous fiber reinforced polyamic acid resin matrix composite laminates

Science.gov (United States)

Druyun, Darleen A. (Inventor); Hou, Tan-Hung (Inventor); Kidder, Paul W. (Inventor); Reddy, Rakasi M. (Inventor); Baucom, Robert M. (Inventor)

1994-01-01

A low pressure processor was developed for preparing a well-consolidated polyimide composite laminate. Prepreg plies were formed from unidirectional fibers and a polyamic acid resin solution. Molding stops were placed at the sides of a matched metal die mold. The prepreg plies were cut shorter than the length of the mold in the in-plane lateral direction and were stacked between the molding stops to a height which was higher than the molding stops. The plies were then compressed to the height of the stops and heated to allow the volatiles to escape and to start the imidization reaction. After removing the stops from the mold, the heat was increased and 0 - 500 psi was applied to complete the imidization reaction. The heat and pressure were further increased to form a consolidated polyimide composite laminate.

The determination of phosphorus in uranium minerals and resulting solutions

International Nuclear Information System (INIS)

Petrement Eguiluz, J. C.; Parellada Bellod, R.; Fernandez Cellini, R.

1964-01-01

Interferences of several elements present in Spanish uranium minerals in the phosphorus determination by the spectrophotometrical method of the molibdovanada te phosphoric acid are studied. A method is described with a previous separation of these element by a cationic resin. This method is successfully applied to the phosphorus determination in acid or alkaline lixiviation solutions of uranium minerals, as well as in the evaluates of ion exchange resins used used technically for the concentration of solutions with a low uranium content. (Author) 11 refs

Epoxidation of linseed oil-Alkyd resins

International Nuclear Information System (INIS)

Motawie, A.M.; Ismail, E.A.; Mazroua, A.M.; Abd EI Aziem, M.S.; Ramadan, A.M.

2004-01-01

Three types of different linseed oil-alkyd resin ( Alk (I), Alk (II), and Alk (III) ) were prepared with the calculated amounts of mono glycerides and adipic acid (1:1, 1:2, and 2:1 Eq.Wt) respectively via monoglyceride method. The obtained alkyd resins were epoxidized via reaction with the calculated quantities of peracetic acid, which was prepared by the reaction of acetic anhydride with H 2 O 2 . Epoxidation occurred with the ratio (1: 1, 1 :3, and 1:6 Eq. Wt) of alkyd to peracetic acid. The effect of reaction time on the epoxy group content was measured during the epoxidation process. The prepared alkyd resins were analyzed by IR and H 1 NMR. The metal coated film properties of epoxidized alkyd resins were compared with those of unmodified alkyd resins. It was observed that the coating films of epoxidized alkyd resins have better in drying properties, hardness, adhesion, impact and flexibility than those of un epoxidized alkyd resins. The flammability properties of the paper coated films for the prepared brominated epoxidized alkyd resins were found to be fire retardant

Lysine purification with cation exchange resin

International Nuclear Information System (INIS)

Khayati, GH.; Mottaghi Talab, M.; Hamooni Hagheeghat, M.; Fatemi, M.

2003-01-01

L-lysine is an essential amino acid for the growth most of animal species and the number one limiting amino acid for poultry. After production and biomass removal by filtration and centrifugation, the essential next step is the lysine purification and recovery. There are different methods for lysine purification. The ion exchange process is one of the most commonly used purification methods. Lysine recovery was done from broth by ion exchange resin in three different ways: repeated passing, resin soaking and the usual method. Impurities were isolated from the column by repeated wash with distilled water. Recovery and purification was done with NH 4 OH and different alcohol volumes respectively. The results showed that repeated passing is the best method for lysine absorption (maximum range 86.21 %). Washing with alkali solution revealed that most of lysine is obtained in the first step of washing. The highest degree of lysine purification was achieved with the use of 4 volumes of alcohol

Dissolution of ion exchange resin by hydrogen peroxide

International Nuclear Information System (INIS)

Lee, S.C.

1981-08-01

The resin dissolution process was conducted successfully in full-scale equipment at the SRL Semiworks. A solution containing 0.001M Fe 2+ , or Fe 3+ , and 3 vol % H 2 O 2 in 0.1M HNO 3 is sufficient to dissolve up to 40 vol % resin slurry (Dowex 50W-X8). Foaming and pressurization can be eliminated by maintaining the dissolution temperature below 99 0 C. The recommended dissolution temperature range is 85 to 90 0 C. Premixing hydrogen peroxide with all reactants will not create a safety hazard, but operating with a continual feed of hydrogen peroxide is recommended to control the dissolution rate. An air sparging rate of 1.0 to 1.5 scfm will provide sufficient mixing. Spent resin from chemical separation contains DTPA (diethylenetriaminepentaacetic acid) residue, and the resin must be washed with 0.1M NH 4 OH to remove excess DTPA before dissolution. Gamma irradiation of resin up to 4 kW-hr/L did not change the dissolution rate significantly

Phosphorus recovery as struvite from eutropic waters by XDA-7 resin.

Science.gov (United States)

Li, Huanwen; Ye, Zhiping; Lin, Ying; Wang, Fengying

2012-01-01

Phosphorus releases into aquatic environment and its subsequent contribution to eutrophication have resulted in a widespread global pollution issue. However, phosphorus is a non-renewable source. The potential supplies of phosphorus are decreasing worldwide. Therefore, removal and recovery of phosphorus from the eutropic waters is important, emergent and necessary. In this research, experiments for recovering phosphate from eutropic waters by anion exchange combined with struvite precipitation were conducted. The results indicated that the prepared XDA-7 resin was an effective adsorbent for phosphate. The adsorption isotherm of XDA-7 resin was found to be a modified Freundlich type. The maximum phosphate adsorption (20.9 mg/g) occurred in the pH range of 6.0-8.0. Phosphate adsorbed on the XDA-7 resin was effectively desorbed with 8% NaCl solution, and the resin was able to be regenerated with 3% NaClO and 4% NaOH solutions. Phosphate desorbed from the resin was recovered as magnesium ammonium phosphate (struvite). The obtained struvite was analyzed by acid dissolution method, scanning electron microscope (SEM) and Fourier transform infrared spectroscopy (FTIR). The struvite precipitate was found to be 75.8% in purity, a high-value fertilizer.

Modified resins for solid-phase extraction

Science.gov (United States)

Fritz, James S.; Sun, Jeffrey J.

1991-12-10

A process of treating aqueous solutions to remove organic solute contaminants by contacting an aqueous solution containing polar organic solute contaminants with a functionalized polystyrene-divinyl benzene adsorbent resin, with the functionalization of said resin being accomplished by organic hydrophilic groups such as hydroxymethyl, acetyl and cyanomethyl.

A Cocatalytic Effect between Meldrum's Acid and Benzoxazine Compounds in Preparation of High Performance Thermosetting Resins.

Science.gov (United States)

Chen, Yi; Lin, Liang-Kai; Chiang, Shu-Jen; Liu, Ying-Ling

2017-02-01

In this work, a cocatalytic effect between Meldrum's acid (MA) and benzoxazine (Bz) compounds has been explored to build up a self-promoting curing system. Consequently, the MA/Bz reactive blend exhibits a relatively low reaction temperature compared to the required temperatures for the cross-linking reactions of the pure MA and Bz components. This feature is attractive for energy-saving processing issues. Moreover, the thermosetting resins based on the MA/Bz reactive blends have been prepared. The MA component can generate additional free volume in the resulting resins, so as to trap air in the resin matrix and consequently to bring low dielectric constants to the resins. The MA-containing agent is an effective modifier for benzoxazine resins to reduce their dielectric constants. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Synthesis of hemicellulose-acrylic acid graft copolymer super water absorbent resin by ultrasonic irradiation technology

Directory of Open Access Journals (Sweden)

Fangfang LIU

2015-12-01

Full Text Available The hemicellulose super water absorbent resin is prepared by using ultrasonic irradiation technology, with the waste liquid produced during the preparation of viscose fiber which contains a large amount of hemicellulose as raw material, acrylic acid as graft monomer, N,N’-methylene bis acrylamide (NMBA as cross linking agent, and (NH42S2O8-NaHSO3 as the redox initiation system. The synthesis conditions, structure and water absorption ability of resin are discussed. The results indicate that water absorbency of the resin is 311 g/g, the tap water absorbency is 102 g/g, the normal saline absorbency is 55 g/g, and the artificial urine absorbency is 31 g/g under the optimal synthesis conditions, so the resin has great water absorption rate and water retaining capacity. The FT-IR and SEM analysis shows that the resin with honeycomb network structure is prepared. The successfully synthesized of the resin means that the hemicellulose waste liquid can be highly effectively recycled, and it provides a kind of new raw material for the synthesis of super water absorbent resin.

Improvement of epoxy resin properties by incorporation of TiO2 nanoparticles surface modified with gallic acid esters

International Nuclear Information System (INIS)

Radoman, Tijana S.; Džunuzović, Jasna V.; Jeremić, Katarina B.; Grgur, Branimir N.; Miličević, Dejan S.; Popović, Ivanka G.; Džunuzović, Enis S.

2014-01-01

Highlights: • Nanocomposites of epoxy resin and TiO 2 nanoparticles surface modified with gallates. • The T g of epoxy resin was increased by incorporation of surface modified TiO 2 . • WVTR of epoxy resin decreased in the presence of surface modified TiO 2 nanoparticles. • WVTR of nanocomposites was reduced with increasing gallates hydrophobic chain length. • Modified TiO 2 nanoparticles react as oxygen scavengers, inhibiting steel corrosion. - Abstract: Epoxy resin/titanium dioxide (epoxy/TiO 2 ) nanocomposites were obtained by incorporation of TiO 2 nanoparticles surface modified with gallic acid esters in epoxy resin. TiO 2 nanoparticles were obtained by acid catalyzed hydrolysis of titanium isopropoxide and their structural characterization was performed by X-ray diffraction and transmission electron microscopy. Three gallic acid esters, having different hydrophobic part, were used for surface modification of the synthesized TiO 2 nanoparticles: propyl, hexyl and lauryl gallate. The gallate chemisorption onto surface of TiO 2 nanoparticles was confirmed by Fourier transform infrared and ultraviolet–visible spectroscopy, while the amount of surface-bonded gallates was determined using thermogravimetric analysis. The influence of the surface modified TiO 2 nanoparticles, as well as the length of hydrophobic part of the gallate used for surface modification of TiO 2 nanoparticles, on glass transition temperature, barrier, dielectric and anticorrosive properties of epoxy resin was investigated by differential scanning calorimetry, water vapor transmission test, dielectric spectroscopy, electrochemical impedance spectroscopy and polarization measurements. Incorporation of surface modified TiO 2 nanoparticles in epoxy resin caused increase of glass transition temperature and decrease of the water vapor permeability of epoxy resin. The water vapor transmission rate of epoxy/TiO 2 nanocomposites was reduced with increasing hydrophobic part chain length of

Removal of CdTe in acidic media by magnetic ion-exchange resin: A potential recycling methodology for cadmium telluride photovoltaic waste

Energy Technology Data Exchange (ETDEWEB)

Zhang, Teng, E-mail: zhangteng@mail.iee.ac.cn; Dong, Zebin; Qu, Fei; Ding, Fazhu; Peng, Xingyu; Wang, Hongyan; Gu, Hongwei

2014-08-30

Highlights: • Sulfonated magnetic microsphere was prepared as one strong acid cation-exchange resin. • Cd and Te can be removed directly from the highly acidic leaching solution of CdTe. • Good chemical stability, fast adsorbing rate and quick magnetic separation in strong acidic media. • A potential path for recycling CdTe photovoltaic waste. - Abstract: Sulfonated magnetic microspheres (PSt-DVB-SNa MPs) have been successfully prepared as adsorbents via an aqueous suspension polymerization of styrene-divinylbenzene and a sulfonation reaction successively. The resulting adsorbents were confirmed by means of Fourier transform infrared spectra (FT-IR), X-ray diffraction (XRD), transmission electron microscope (TEM), scanning electron microscope equipped with an energy dispersive spectrometer (SEM-EDS) and vibrating sample magnetometer (VSM). The leaching process of CdTe was optimized, and the removal efficiency of Cd and Te from the leaching solution was investigated. The adsorbents could directly remove all cations of Cd and Te from a highly acidic leaching solution of CdTe. The adsorption process for Cd and Te reached equilibrium in a few minutes and this process highly depended on the dosage of adsorbents and the affinity of sulfonate groups with cations. Because of its good adsorption capacity in strong acidic media, high adsorbing rate, and efficient magnetic separation from the solution, PSt-DVB-SNa MPs is expected to be an ideal material for the recycling of CdTe photovoltaic waste.

Technical Task and Quality Assurance Plan in Support of BNFL Part B: Studies of Ion Exchange Resin Integrity under Flowsheet Extremes: Part II

International Nuclear Information System (INIS)

Nash, C.A.

2000-01-01

This task will address four items related to ion exchange stability: (1) process upset evaluation of resin in contact with 1 molar sodium permanganate at 25 and 40 degrees C, (2) accelerated aging with nitric acid solution used during normal regeneration operations, (3) prolonged contacting of SuperLig 644 resin with 5 molar nitric acid at room temperature, and (4) prolonged contacting of SuperLig 644 resin with deionized water at 60 plus/minus 5 degrees C

Glucose-lowering effects and mechanisms of the bile acid-sequestering resin sevelamer

DEFF Research Database (Denmark)

Brønden, Andreas; Mikkelsen, Kristian; Sonne, David P

2018-01-01

AIMS: Sevelamer, a non-absorbable amine-based resin used for treatment of hyperphosphatemia, has been demonstrated to hold a marked bile acid-binding potential alongside beneficial effects on lipid and glucose metabolism. The aim of this study was to investigate the glucose-lowering effect and me...

Biophysical study of resin acid effects on phospholipid membrane structure and properties

DEFF Research Database (Denmark)

Jagalski, Vivien; Barker, Robert; Topgaard, Daniel

2016-01-01

Hydrophobic resin acids (RAs) are synthesized by conifer trees as part of their defense mechanisms. One of the functions of RAs in plant defense is suggested to be the perturbation of the cellular membrane. However, there is a vast diversity of chemical structures within this class of molecules, ...

Removing and recovering of uranium from the acid mine waters by using ion exchange resin; Remocao e recuperacao de uranio de aguas acidas de mina por resina de troca ionica

Energy Technology Data Exchange (ETDEWEB)

Nascimento, Marcos Roberto Lopes do

1998-07-01

Ion exchange using resins is one of the few processes capable of reducing ionic contaminants in effluents to very low levels. In this study the process was used to remove and recovery uranium from acid mine waters at Pocos de Caldas-MG Uranium Mining and Milling Plant. The local mineralogical features, allied to the biogeochemical phenomena, owing to presence of pyrite in the rock piles, moreover another factors, resulting acid drainage with several pollutants, including uranium ranging from 6 to 14 mg/l, as sulfate complex, that can be removed by anionic exchanger. The iron interference is eliminated by lime pretreatment of water, increasing pH from 2.6 to 3.3-3.8 to precipitate this cation, without changing the uranium amount. Eight anionic resins were tested, based on the uranium loading, in sorption studies. Retention time, and pH influence was verified for the exchanger chose. With breakthrough of 1 mg U/L and 10 mg U/l in the feed solution, the uranium decontamination level was 94%. Typical values of loading resin were 20-30 g U/l and 70-90 g SO{sub 4}/l. Uranium elution was done with Na Cl solution. Retention time, saline, and acid concentration were the parameters studied. The concentrate, obtained from the eluate by ammonia precipitation, presented uranium (86,8% as U{sub 3} O{sub 8}) and impurities within commercial specifications. (author)

Application of 10% Ascorbic Acid Improves Resin Shear Bond Stregth in Bleached Dentin

Directory of Open Access Journals (Sweden)

Kamizar Kamizar

2014-10-01

Full Text Available Normal 0 false false false IN X-NONE X-NONE MicrosoftInternetExplorer4 Restoration of the teeth immediately after bleaching with H2O2 35% is contraindicated due to the remnants of free radical that will stay inside dentin for 2-3 weeks which will compromise the adhesiveness of composite resin. Objective: The aim of this study was to evaluate the influence of 10% ascorbic acid on shear bond strength of composite placed on bleached dentin. Methods:Twenty seven samples were divided equally into three groups. Group 1: dentin was etched with 35% phosphoric acid; Group 2: dentin was bleached with 35% H2O2 followed by etching with 35% phosphoric acid; Group 3: dentin was bleached with 35% H2O2, followed by application of 10% ascorbic acid and etched with 35% phosphoric acid. All samples were then stored at 370C for 24 hours. The Universal Testing Machine was used to measure shear bond strength and the results were analyzed with Kruskal Wallis and Mann Whitney test. Results: After nine independent experiments, 10% ascorbic acid application on bleached dentin resulted in highest increased in bond stregth (56.04±11.06MPa compared to Group 2 (29.09±7.63MPa and Group 1 (25.55±2.22MPa and the difference was statistically significant (p<0.05. Conclusion: Application of 10% ascorbic acid to the bleached dentin improved the shear bond strength of resin composite.

[Mechanism of gold solid extraction from aurocyanide solution using D3520 resin impregnated with TRPO].

Science.gov (United States)

Yang, Xiang-Jun; Wang, Shi-Xiong; Zou, An-Qin; Chen, Jing; Guo, Hong

2014-02-01

Trialkyphosphine oxides (TRPO) was successfully used for the impregnation of D3520 resin to prepare an extractant-impregnated resin (EIR). Solid extraction of Au(I) from alkaline cyanide solution was studied using this extractant-impregnated resin (EIR), with addition of cetyltrimethylammonium bromide (CTMAB), directly into the aurous aqueous phase in advance. The mechanism of solid extraction was further investigated by means of FTIR, XPS and SEM. The column separation studies have shown that cationic surfactant CTMAB played a key role in the solid phase extraction, and the resin containing TRPO were effective for the extraction of gold when the molar ratio of CTMAB: Au( I ) reached 1:1. FTIR spectroscopy of gold loaded EIR showed that the frequency of C[triple bond]N stretching vibration was at 2144 cm(-1), and the frequency of P=O stretching vibration shifted to lower frequency from 1153 to 1150 cm(-1). The XPS spectrum of N(1s), Au(4f7/2) and Au(4f5/2) sugges- ted that the coordination environment of gold did not change before and after extraction, and gold was still as the form of Au (CN)2(-) anion exiting in the loaded resin; O(1s) spectrum showed that the chemically combined water significantly increased after solid extraction from 30.74% to 42.34%; Comparing to the P(2p) spectrum before and after extraction, the binding energy increased from 132. 15 to 132. 45 eV, indicating there maybe existing hydrogen-bond interaction between P=O and water molecule, such as P=O...H-O-H. The above results obtained established that in the solid extraction process, the hydrophobic ion association [CTMA+ x Au(CN)] diffused from the bulk solution into the pores of the EIR, and then be solvated by TRPO adsorbed in the pores through hydrogen bonding bridged by the water molecules.

A thermodynamic and kinetic study of trace iron removal from aqueous cobalt sulfate solutions using Monophos resin.

Science.gov (United States)

Wang, Guangxin; Zhao, Yunchao; Yang, Bin; Song, Yongfa

2018-01-01

High purity cobalt has many important applications, such as magnetic recording media, magnetic recording heads, optoelectronic devices, magnetic sensors, and integrated circuits, etc. To produce 5N or higher purity cobalt in an electro-refining process, one of the challenges is to effectively reduce the Fe content of aqueous cobalt salt solution before electrolysis. This paper describes thermodynamic and kinetic investigations of the Fe adsorption process of a new sulfonated monophosphonic resin with the trade mark Monophos. Five cobalt sulfate solutions of different Co concentrations were prepared. Fe ions were removed from the solutions by ion exchange method using Monophos resin. Chemical analysis was carried out using a Perkin Elmer ICP-OES. The initial Fe concentrations of about 0.9-2.0 mg/L can be reduced to about 0.3-0.8 mg/L, which is equivalent to an Fe removal rate of 60-67%. The Langmuir isothermal adsorption model applies well to the Fe removal process. A second-order type based on McKay equation fits better with experimental data than other kinetic models. The kinetic curve can be divided into two sections. For t 30 min. Monophos resin is effective for the removal of trace Fe from cobalt sulfate solution. This ion exchange process obeys the Langmuir isothermal adsorption model and the McKay equation of second-order kinetics.

Development of Highly Nano-Dispersed NiO/GDC Catalysts from Ion Exchange Resin Templates

Directory of Open Access Journals (Sweden)

Angel Caravaca

2017-11-01

Full Text Available Novel NiO/GDC (Gadolinium-doped Ceria cermet catalysts were developed by the Weak Acid Resin (WAR method using an ion exchange resin template. In addition, the specific surface area of these tunable materials was enhanced by NiO partial dissolution in aqueous acid solution. The whole procedure highly improved the micro-structural properties of these materials compared to previous studies. Catalysts with high metal loadings (≥10%, small Ni nanoparticles (<10 nm, and high specific surface areas (>70 m2/g were achieved. These properties are promising for catalytic applications such as methane steam reforming for H2 production.

Study and application of new chelating resin to recovery uranium from in-situ leach solution with high content saline chloride ion

International Nuclear Information System (INIS)

Zhang Jianguo; Qiu Yueshuang; Feng Yu; Deng Huidong; Zhao Chaoya

2014-01-01

Research on the adsorption and elution property of D814 chelating resin was carried out aiming at the difficult separation of uranium from high content saline chloride ion in situ leach liquor and the adsorption mechanism is also discussed. Influence factors such as contact time, pH value, Ca"2"+, Mg"2"+ and Cl"- concentration etc. to the resin adsorption were studied. Experimental results show that adsorption rate is lowly which need 6h to arrive at the adsorption equilibrium. The resin adsorption uranium pH in the solution is from l.33 to 9. When total salinity is over 20 g/L, calcium ion, and magnesium ion is about 3 g/L, there are no big influence on resin adsorption capacity. The resin has good chloride ion resistance. When chloride ion is over 60 g/L, it is no influence on resin adsorption uranium. Column experiment results indicate that ratio of saturation volume to break-through point volume is l.82, resin saturation uranium capacity is 40.5 mg. U/_g_(_∓_)_R. When elution volume bed number is 23, the eluted solution uranium concentration is below 80 mg/L. The elution rate of the uranium is 96.2%. (authors)

Behavior of cationic, anionic and colloidal species of titanium, zirconium and thorium in presence of ion exchange resins

International Nuclear Information System (INIS)

Souza Filho, G. de; Abrao, A.

1976-01-01

The distribution of titanium, zirconium and thorium is aqueous and resin phases has been studied using strong cationic resin in the R-NH 4 form. Solutions of the above elements in perchloric, nitric, hydrochloric and suphuric media were used. Each set of experiments was made by separately varying one of the five parameters - type of anion present, acidity of solution, temperature of percolation, age of solution and concentration of the element. It was found that, depending on the particular balance of these parameters, the elements investigated may be found in acidic solutions either as cationic, anionic or colloidal species. It is emphasized that the colloidal species of titanium, zirconium or thorium are not retained by the ion exchangers, and from this property a method for the separation and purification of the above elements has been outlined [pt

Polyvinyl chloride resin

International Nuclear Information System (INIS)

Kim, Hong Jae

1976-06-01

This book contains polyvinyl chloride resin industry with present condition such as plastic industry and polyvinyl chloride in the world and Japan, manufacture of polyvinyl chloride resin ; suspension polymerization and solution polymerization, extruding, injection process, hollow molding vinyl record, vacuum forming, polymer powders process, vinyl chloride varnish, vinyl chloride latex, safety and construction on vinyl chloride. Each chapter has descriptions on of process and kinds of polyvinyl chloride resin.

An Efficient Protocol for Preparation of Gallic Acid from Terminalia bellirica (Gaertn.) Roxb by Combination of Macroporous Resin and Preparative High-Performance Liquid Chromatography.

Science.gov (United States)

Zou, Denglang; Chen, Tao; Chen, Chen; Li, Hongmei; Liu, Yongling; Li, Yulin

2016-08-01

In this article, macroporous resin column chromatography and preparative high-performance liquid chromatography were applied for preparation of gallic acid from Terminalia bellirica (Gaertn.) Roxb. In the first step, six kinds of resins were investigated by adsorption and desorption tests and AB-8 macroporous resin was selected for the enrichment of gallic acid. As a result, 20 g of gallic acid at a purity of 71% could be separated from 100 g of crude extract in which the content of gallic acid was 16.7% and the recovery of gallic acid reached 85.0%. In the second step, preparative high-performance liquid chromatography was selected to purify gallic acid. As a result, 640 mg of gallic acid at a purity of 99.1% was obtained from 1 g of sample in 35 min. The results demonstrated that macroporous resin coupled with preparative high-performance liquid chromatography was suitable for preparation of gallic acid from T. bellirica (Gaertn.) Roxb. © The Author 2016. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Safety evaluation of cation-exchange resins

International Nuclear Information System (INIS)

Kalkwarf, D.R.

1977-08-01

Results are presented of a study to evaluate whether sufficient information is available to establish conservative limits for the safe use of cation-exchange resins in separating radionuclides and, if not, to recommend what new data should be acquired. The study was also an attempt to identify in-line analytical techniques for the evaluation of resin degradation during radionuclide processing. The report is based upon a review of the published literature and upon discussions with many people engaged in the use of these resins. It was concluded that the chief hazard in the use of cation-exchange resins for separating radionuclides is a thermal explosion if nitric acid or other strong oxidants are present in the process solution. Thermal explosions can be avoided by limiting process parameters so that the rates of heat and gas generation in the system do not exceed the rates for their transfer to the surroundings. Such parameters include temperature, oxidant concentration, the amounts of possible catalysts, the radiation dose absorbed by the resin and the diameter of the resin column. Current information is not sufficient to define safe upper limits for these parameters. They can be evaluated, however, from equations derived from the Frank-Kamenetskii theory of thermal explosions provided the heat capacities, thermal conductivities and rates of heat evolution in the relevant resin-oxidant mixtures are known. It is recommended that such measurements be made and the appropriate limits be evaluated. A list of additional safety precautions are also presented to aid in the application of these limits and to provide additional margins of safety. In-line evaluation of resin degradation to assess its safety hazard is considered impractical. Rather, it is recommended that the resin be removed from use before it has received the limiting radiation dose, evaluated as described above

Esterification of free fatty acids in waste cooking oils (WCO): Role of ion-exchange resins

Energy Technology Data Exchange (ETDEWEB)

Nalan Ozbay; Nuray Oktar; N. Alper Tapan [Gazi University, Ankara (Turkey). Faculty of Engineering and Architecture, Department of Chemical Engineering

2008-08-15

Although WCO plays a crucial role for the economical production of biodiesel, free fatty acid (FFA) level in the nature of WCO cause saponification problems during transesterification. Acidic ion-exchange resins can be used to decrease WCO free fatty acid level. In this study, activities of resins (Amberlyst-15 (A-15), Amberlyst-35 (A-35), Amberlyst-16 (A-16) and Dowex HCR-W2) in direct FFA esterification were examined in the temperature range of 50-60{sup o}C and the effect of catalyst amount (1-2 wt%) on FFA conversion was also analyzed. FFA conversion increased with increasing reaction temperature and catalyst amount. Order of catalytic activities was found as A-15 > A-35 > A-16 > Dowex HCR-W2. This was related to the size of average pore diameters and magnitude of BET surface area. 44 refs., 11 figs., 2 tabs.

Use of a polystyrene-divinylbenzene-based weakly acidic cation-exchange resin column and propionic acid as an eluent in ion-exclusion/adsorption chromatography of aliphatic carboxylic acids and ethanol in food samples.

Science.gov (United States)

Mori, Masanobu; Hironaga, Takahiro; Kajiwara, Hiroe; Nakatani, Nobutake; Kozaki, Daisuke; Itabashi, Hideyuki; Tanaka, Kazuhiko

2011-01-01

We developed an ion-exclusion/adsorption chromatography (IEAC) method employing a polystyrene-divinylbenzene-based weakly acidic cation-exchange resin (PS-WCX) column with propionic acid as the eluent for the simultaneous determination of multivalent aliphatic carboxylic acids and ethanol in food samples. The PS-WCX column well resolved mono-, di-, and trivalent carboxylic acids in the acidic eluent. Propionic acid as the eluent gave a higher signal-to-noise ratio, and enabled sensitive conductimetric detection of analyte acids. We found the optimal separation condition to be the combination of a PS-WCX column and 20-mM propionic acid. Practical applicability of the developed method was confirmed by using a short precolumn with a strongly acidic cation-exchange resin in the H(+)-form connected before the separation column; this was to remove cations from food samples by converting them to hydrogen ions. Consequently, common carboxylic acids and ethanol in beer, wine, and soy sauce were successfully separated by the developed method.

Separation of Mn(II) in presence of Al(III) in acid drainage from an Uranium mine with the use of chelating resins

International Nuclear Information System (INIS)

Soares, Eliane Pavesi B.; Gomes, Viviane T.; Vaitsman, Delmo S.

2011-01-01

The acid drainage of Osamu Utsumi mine is the main environmental impact from mining activities in Pocos de Caldas - MG - Brazil. The water produced in this process is characterized by high acidity and heavy metal concentration. To minimize this environmental impact, new technologies directed towards treatment of acid drainage of mine (ADM) have been studied. However, due to the presence of Al 3+ (which has a high charge) in the ADM, these resins get quickly saturated, preventing stripping of divalent cations like Mn 2+ . This study proposes the synthesis of chelating resins that provide preferential retention of Mn 2+ instead of Al 3+ . It was synthesized resins functionalized with amidoxime and dithiocarbamate. The capacity of retention of Mn 2+ e Al 3+ ions at different pH values was assessed for each resin. The stripping of Mn 2+ at 2, 3 and 4 (pH ADM range) by studied resins was not preferential for Mn 2+ in relation to Al 3+ , probably due to the strong electrostatic interaction between this last type of high charge density and the active sites from extractor agents and resins. However at pH 6 (stated by environmental norms for liquid effluents discharge) the synthesized resins had a good retention capacity for Mn 2+ . So it is proposed that the extraction technique using chelating resins could be employed to strip Mn 2+ from ADM at pH 6,0, since at this condition , Al 3+ is precipitated as Al(OH) 3 . (author)

Separation and concentration of lead, uranium and copper using polystyrene resins functionalised with azobenzylphosphonic acid ligands

International Nuclear Information System (INIS)

Ueda, Kazumasa; Sato, Yuko; Yoshimura, Osamu; Yamamoto, Yoshikazu

1988-01-01

Two polystyrene resins functionalised with azobenzylphosphonic acid ligands were synthesised and applications for the concentration, separation and determination of micro- or milligram concentrations of metal ions were studied. Physical and chemical properties such as specific mass, water content and ion-exchange capacity were measured and the characteristics of the resins were examined. The resins were especially useful for the concentration of Pbsup(II), Usup(VI) and Cusup(II) by batch and column operations, and effective separations of Pbsup(II) from Group VIII and IIB ions could be achieved by selecting the eluents. Trace amounts of Pbsup(II), Usup(VI), Cusup(II), Mnsup(II), Znsup(II) and Fesup(III) were quantitatively retained on the resin columns at neutral pH and easily recovered by elution with 2M HCl and 2M HNO 3 . The resins were successfully applied to the concentration of trace amounts of metals in river and sea waters prior to spectroscopic determinations. (author)

Factorial experimental design for recovering heavy metals from sludge with ion-exchange resin

International Nuclear Information System (INIS)

Lee, I.H.; Kuan, Y.-C.; Chern, J.-M.

2006-01-01

Wastewaters containing heavy metals are usually treated by chemical precipitation method in Taiwan. This method can remove heavy metals form wastewaters efficiently, but the resultant heavy metal sludge is classified as hazardous solid waste and becomes another environmental problem. If we can remove heavy metals from sludge, it becomes non-hazardous waste and the treatment cost can be greatly reduced. This study aims at using ion-exchange resin to remove heavy metals such as copper, zinc, cadmium, and chromium from sludge generated by a PCB manufacturing plant. Factorial experimental design methodology was used to study the heavy metal removal efficiency. The total metal concentrations in the sludge, resin, and solution phases were measured respectively after 30 min reaction with varying leaching agents (citric acid and nitric acid); ion-exchange resins (Amberlite IRC-718 and IR-120), and temperatures (50 and 70 deg. C). The experimental results and statistical analysis show that a stronger leaching acid and a higher temperature both favor lower heavy metal residues in the sludge. Two-factors and even three-factor interaction effects on the heavy metal sorption in the resin phase are not negligible. The ion-exchange resin plays an important role in the sludge extraction or metal recovery. Empirical regression models were also obtained and used to predict the heavy metal profiles with satisfactory results

Surface Engineering of PAMAM-SDB Chelating Resin with Diglycolamic Acid (DGA) Functional Group for Efficient Sorption of U(VI) and Th(IV) from Aqueous Medium

Energy Technology Data Exchange (ETDEWEB)

Ilaiyaraja, P.; Venkatraman, B., E-mail: chemila07@gmail.com [Radiological Safety Division, Indira Gandhi Centre for Atomic Research, Kalpakkam (India); Deb, A.K. Singha [Chemical Engineering Division, Bhabha Atomic Research Centre, Mumbai (India); Ponraju, D. [Safety Engineering Division, Indira Gandhi Centre for Atomic Research, Kalpakkam (India); Ali, Sk. Musharaf [Chemical Engineering Division, Bhabha Atomic Research Centre, Mumbai (India)

2017-04-15

Highlights: • A new DGA-PAMAM-SDB chelating resin has been synthesized for actinide sorption. • Maximum sorption capacities of resin are 682 and 544.2 mg g{sup −1}for U(VI) and Th(IV). • DGA-PAMAM-SDB chelating resin could be regenerated and reused. • DFT calculation of actinides interaction with resin corroborates the experimental. • Resin is effective for sorption of actinides from both aqueous and HNO{sub 3} medium. - Abstract: A novel chelating resin obtained via growth of PAMAM dendron on surface of styrene divinyl benzene resin beads, followed by diglycolamic acid functionalization of the dendrimer terminal. Batch experiments were conducted to study the effects of pH, nitric acid concentration, amount of adsorbent, shaking time, initial metal ion concentration and temperature on U(VI) and Th(IV) adsorption efficiency. Diglycolamic acid terminated PAMAM dendrimer functionalized styrene divinylbenzene chelating resin (DGA-PAMAM-SDB) is found to be an efficient candidate for the removal of U(VI) and Th(IV) ions from aqueous (pH > 4) and nitric acid media (> 3 M). The sorption equilibrium could be reached within 60 min, and the experimental data fits with pseudo-second-order model. Langmuir sorption isotherm model correlates well with sorption equilibrium data. The maximum U(VI) and Th(IV) sorption capacity onto DGA-PAMAMG{sub 5}-SDB was estimated to be about 682 and 544.2 mg g{sup −1} respectively at 25 °C. The interaction of actinides and chelating resin is reversible and hence, the resin can be regenerated and reused. DFT calculation on the interaction of U(VI) and Th(IV) ions with chelating resin validates the experimental findings.

Esterification of Palmitic Acid with Methanol in the Presence of Macroporous Ion Exchange Resin as Catalyst

Directory of Open Access Journals (Sweden)

Amelia Qarina Yaakob and Subhash Bhatia

2012-10-01

Full Text Available The esterification of palmitic acid with methanol was studied in a batch reactor using macro porous ion exchange resin Amberlyst 15 as a catalyst. Methyl palmitate was produced from the reaction between palmitic acid and methanol in the presence of catalyst. The effects of processing parameters, molar ratio of alcohol to acid M, (4-10, catalyst loading (0-10 g cat/liter, water inhibition (0-2 mol/liter, agitator speed (200-800 rpm and reaction temperature (343-373K were studied. The experimental kinetic data were correlated using homogenous as well as heterogeneous models (based on single as well as dual site mechanisms. The activation energy of the reaction was 11.552 kJ/mol for forward reaction whilst 5.464 kJ/mol for backward reaction. The experimental data fitted well with the simulated data obtained from the kinetic models. Keywords: Palmitic Acid, Methanol, Esterification, Ion Exchange Resin, Kinetics.

Adsorption of uranium(VI) from sulphate solutions using Amberlite IRA-402 resin: Equilibrium, kinetics and thermodynamics study

International Nuclear Information System (INIS)

Solgy, Mostafa; Taghizadeh, Majid; Ghoddocynejad, Davood

2015-01-01

Highlights: • Adsorption of uranium from sulphate solutions by an anion exchange resin. • The effects of pH, contact time and adsorbent dosage were investigated. • The adsorption equilibrium is well described by the Freundlich isotherm model. • The adsorption kinetics can be predicted by the pseudo second-order model. • The adsorption is a physical, spontaneous and endothermic process. - Abstract: In the present study, adsorption of uranium from sulphate solutions was evaluated using Amberlite IRA-402 resin. The variation of adsorption process was investigated in batch sorption mode. The parameters studied were pH, contact time and adsorbent dosage. Langmuir and Freundlich isotherm models were used in order to present a mathematical description of the equilibrium data at three different temperatures (25 °C, 35 °C and 45 °C). The final results confirmed that the equilibrium data tend to follow Freundlich isotherm model. The maximum adsorption capacity of Amberlite IRA-402 for uranium(VI) was evaluated to be 213 mg/g for the Langmuir model at 25 °C. The adsorption of uranium on the mentioned anion exchange resin was found to follow the pseudo-second order kinetic model, indicating that chemical adsorption was the rate limiting-step. The values of thermodynamic parameters proved that adsorption process of uranium onto Amberlite IRA-402 resin could be considered endothermic (ΔH > 0) and spontaneous (ΔG < 0)

Calcium isotope fractionation in liquid chromatography with benzo-18-crown-6 resin in aqueous hydrobromic acid medium

International Nuclear Information System (INIS)

Sato, Takuya; Oi, Takao

2015-01-01

Liquid chromatography operated in a breakthrough mode was employed to study calcium isotope fractionation in the aqueous hydrobromic acid medium. Highly porous silica beads, the inner pores of which were embedded with a benzo-18-crown-6 ether resin, were used as column packing material. Enrichment of heavier isotopes of calcium was observed in the frontal part of respective calcium chromatograms. The values of the isotope fractionation coefficient were on the order of 10 -3 . The observed isotope fractionation coefficient was dependent on the concentration of hydrobromic acid in the calcium feed solution; a higher HBr concentration resulted in a smaller fractionation coefficient value. The present calcium isotope effects were most probably mass-dependent, indicating that they mostly came from isotope effects based on molecular vibration. Molecular orbital calculations supported the present experimental results in a qualitative fashion. Chromatography operated in aqueous HBr media is a better system of Ca isotope separation than that operated in aqueous HCl media. (author)

The removal of toxic metals from liquid effluents by ion exchange resins. Part VI: Manganese(II/H+/Lewatit K2621

Directory of Open Access Journals (Sweden)

Francisco J. Alguacil

2018-05-01

Full Text Available In this sixth part of the series, Manganese(II was removed from aqueous solutions by the cationic exchange resin Lewatit K2621. The investigation was performed under various experimental conditions such as the stirring speed associated with the system, aqueous pH, temperature, resin dosage and the ionic strength of the solution. The performance of the resin against the loading of metals from metal-binary solutions as well as the removal of Manganese(II from the solutions using multiwalled carbon nanotubes and functionalized (carboxylic groups multiwalled carbon nanotubes, were also investigated. Experimental results fit well with the pseudo-first kinetic order model, whereas fit of the data show that at 20 °C the process responded well to the diffusion controlled model, and that at 60 °C, the system is controlled by the moving boundary model. Adsorption data is better related to the Freundlich isotherm. Elution of the Manganese(II loaded onto the resin was investigated using acidic (H2SO4 or HCl solutions.

Acidic resin-catalysed conversion of fructose into furan derivatives in low boiling point solvents.

Science.gov (United States)

Zhu, Hong; Cao, Quan; Li, Chunhu; Mu, Xindong

2011-09-27

Conversion of fructose into furan derivatives 5-hydroxymethylfurfural (HMF) and 5-methoxymethylfurfural (MMF) is performed in tetrahydrofuran (THF) and methanol-organic solvent systems, catalysed by an acidic resin Amberlyst-15. The melted fructose can be converted into HMF on the surface of the solid resin catalyst in the presence of THF as an extracting phase, which is a good solvent for HMF and other by-products. The solid resin catalyst can be reused eleven times without losing its catalytic ability, with an average HMF yield of approximately 50%. Upon the addition of methanol, the generated HMF can further react with methanol to form MMF, and the total yield of HMF and MMF could be promoted to 65%. GC-MS analysis confirms the formation of a small amount of methyl levulinate in methanolorganic solvent system. Copyright © 2011 Elsevier Ltd. All rights reserved.

Uranium adsorption from the sulphuric acid leach liquor containing more chlorides with cation-exchange resin SL-406

International Nuclear Information System (INIS)

Hu Jun; Wang Zhaoguo; Chi Renqing; Niu Xuejun

1994-01-01

The feasibility of uranium adsorption was studied from the sulphuric acid leach liquor of a uranium ore containing more chlorides with cation-exchange resin SL-406. The influence of some factors on uranium adsorption was investigated. It was shown that the resin possesses better selectivity, stability and higher capacity. It can be effectively used to recovery uranium from leach liquors of uranium ores containing more chlorides

Resin bead-thermal ionization mass spectrometry for determination of plutonium concentration in irradiated fuel dissolver solution

International Nuclear Information System (INIS)

Paul, Sumana; Shah, R.V.; Aggarwal, S.K.; Pandey, A.K.

2015-01-01

Determination of isotopic composition (IC) and concentration of plutonium (Pu) is necessary at various stages of nuclear fuel cycle which involves analysis of complex matrices like dissolver solution of irradiated fuel, nuclear waste stream etc. Mass spectrometry, e.g. thermal ionization mass spectrometry (TIMS) and inductively coupled plasma mass spectrometry (ICP-MS) are commonly used for determination of IC and concentration of plutonium. However, to circumvent matrix interferences, efficient separation as well as preconcentration of Pu is required prior to mass spectrometric analysis. Purification steps employing ion-exchange resins are widely used for the separation of Pu from dissolver solution or from mixture of other actinides e.g. U, Am. However, an alternative way is to selectively preconcentrate Pu on a resin bead, followed by direct loading of the bead on the filament of thermal ionization mass spectrometer

Recovery of boric acid from ion exchangers

International Nuclear Information System (INIS)

Pollock, C.W.

1976-01-01

The recovery of boric acid from an anion exchange resin is improved by eluting the boric acid with an aqueous solution of ammonium bicarbonate. The boric acid can be readily purified and concentrated by distilling off the water and ammonium bicarbonate. This process is especially useful for the recovery of boric acid containing a high percentage of 10 B which may be found in some nuclear reactor coolant solutions. 10 claims

Study on Selective Removal of Impurity Iron from Leached Copper-Bearing Solution Using a Chelating Resin

Directory of Open Access Journals (Sweden)

Yubiao Li

2016-10-01

Full Text Available In order to selectively remove iron from copper laden solution after leaching but prior to electrowinning, equilibrium, kinetic, and thermodynamic studies have been conducted on an a chelating resin of Rexp-501 at pH 1.0 and at various temperatures. Both Langmuir and Freundlich models were investigated, with the Langmuir model proving to be more suitable for fitting iron removal performance, with little influence from copper concentration. Compared with the pseudo first order kinetic model, the pseudo second order kinetic model fitted the dynamic adsorption process better, indicating a chemisorption mechanism. Fourier transform infrared spectroscopy (FT-IR results indicated that C=O from carbonyl group played a key role in combining with iron and can be regenerated and reused. However, the C=O of the acylamino group combining with iron was not able to be released after oxalic acid was applied.

A convenient procedure for the solid-phase synthesis of hydroxamic acids on PEGA resins

DEFF Research Database (Denmark)

Nandurkar, Nitin Subhash; Petersen, Rico; Qvortrup, Katrine

2011-01-01

An efficient method for the solid-phase synthesis of hydroxamic acids is described. The method comprises the nucleophilic displacement of esters immobilized on PEGA resins with hydroxylamine/sodium hydroxide in isopropanol. The hydroxyaminolysis protocol is compatible with a broad range of PEGA...

Ion Exchange Temperature Testing with SRF Resin - 12088

Energy Technology Data Exchange (ETDEWEB)

Russell, R.L.; Rinehart, D.E.; Brown, G.N.; Peterson, R.A. [Pacific Northwest National Laboratory, Richland, WA 99352 (United States)

2012-07-01

Ion exchange using the Spherical Resorcinol-Formaldehyde (SRF) resin has been selected by the U.S. Department of Energy's Office of River Protection for use in the Pretreatment Facility of the Hanford Tank Waste Treatment and Immobilization Plant (WTP) and for potential application in an at-tank deployment for removing Cs-137. Recent proposed changes to the WTP ion exchange process baseline indicate that higher temperatures (50 deg. C) to alleviate post-filtration precipitation issues prior to reaching the ion exchange columns may be required. Therefore, it is important to understand the behavior of SRF resin performance under the conditions expected with the new equipment and process changes. This research examined the impact of elevated temperature on resin loading and resin degradation during extended solution flow at elevated temperature (45 deg., 50 deg., 55 deg., 60 deg., 65 deg., 75 deg. C). Testing for extended times at elevated temperatures showed that the resin does degrade and loading capacity is reduced at and above 45 deg. C. Above 60 deg. C the resin appears to not load at all. It was observed that the resin disintegrated at 75 deg. C until not much was left and partially disintegrated at 65 deg. C, which caused the column to plug in both tests after ∼336 hours. The results indicate that WTP will lose resin loading capacity if the ion exchange process is performed above 25 deg. C, and the resin will disintegrate above 65 deg. C. Therefore, WTP will have a restricted operating range of temperatures to perform the ion exchange process with this resin. PNNL and WTP are currently evaluating the operating limits of the resin in further detail. Aging in 0.5 M HNO{sub 3} also caused the resin to lose capacity above 25 deg. C and to completely dissolve at 55 deg. C. Again, WTP will have a restricted operating range of temperatures when eluting the resin with nitric acid in order to maintain resin loading capacity and avoid disintegration of the resin

Metal binding characterization and conformational studies using Raman microscopy of resin-bound poly(aspartic acid).

Science.gov (United States)

Stair, Jacqueline L; Holcombe, James A

2007-03-01

The metal binding capacities, conditional stability constants, and secondary structure of immobilized polyaspartic acid (PLAsp) (n = 6, 20, and 30) on TentaGel resin were determined when binding Mg2+, Co2+, Cd2+, and Ni2+. Metal binding to the synthesized peptides was evaluated using breakthrough curves from a packed microcolumn and flame atomic absorption spectrophotometry (FAAS) detection. The metal capacities reached values of 590, 2160, and 3710 mumol of metal/g of resin for the 6-mer, 20-mer, and 30-mer, respectively, and this resulted in 2-3 residues per metal for all peptides and metals tested. Surprisingly, the concentrated environment of the resin along with the spatial distribution of attachment groups allowed for most residues to participate in metal binding regardless of the peptide length. Conditional stability constants calculated using single metal binding isotherms indicated that binding strength decreased as the chain length increased on the resin. Raman microscopy on single beads was used to determine PLAsp secondary structure, and all peptides were of a mixed conformation (i.e., beta-sheets, alpha-helices, random chain, etc.) during neutral conditioning and metal binding. Uniquely, the longer 20-mer and 30-mer peptides showed a distinct change from a mixed conformation to beta-sheets and alpha-helices during metal release with acid. This study confirms that metal release by longer immobilized peptides is often assisted by a conformational change, which easily spoils the binding cavity, while shorter peptides may release metal primarily by H+ displacement.

Inhibition of enamel demineralization and bond-strength properties of bioactive glass containing 4-META/MMA-TBB-based resin adhesive.

Science.gov (United States)

Kohda, Naohisa; Iijima, Masahiro; Kawaguchi, Kyotaro; Toshima, Hirokazu; Muguruma, Takeshi; Endo, Kazuhiko; Mizoguchi, Itaru

2015-06-01

We investigated the enamel demineralization-prevention ability and shear bond strength (SBS) properties of 4-methacryloxyethyl trimellitic anhydride/methyl methacrylate-tri-n-butyl borane (4-META/MMA-TBB)-based resin containing various amounts (0-50%) of bioactive glass (BG). Disk-shaped specimens were immersed in distilled water and ions released were analysed by inductively coupled plasma atomic-emission spectroscopy. Samples were also immersed in lactic acid solution (pH 4.6) to estimate acid-neutralizing ability. Brackets were bonded to human premolars with BG-containing resins and the bonded teeth were alternately immersed in demineralizing (pH 4.55) and remineralizing (pH 6.8) solutions for 14 d. The enamel hardness was determined by nanoindentation testing at twenty equidistant distances from the external surface. The SBS for each sample was examined. The amounts of ions released [calcium (Ca), sodium (Na), silicon (Si), and boron (B)] and the acid-neutralizing ability increased with increasing BG content. After alternating immersion, the specimens bonded with the BG-containing resin with high BG content were harder than those in the other groups in some locations 1-18.5 μm from the enamel surface. Bioactive glass-containing (10-40%) resin had bond strength equivalent to the control specimen. Thus, the SBS obtained for BG-containing resin (6.5-9.2 MPa) was clinically acceptable, suggesting that this material has the ability to prevent enamel demineralization. © 2015 Eur J Oral Sci.

Petroleum Resins: Separation, Character, and Role in Petroleum

DEFF Research Database (Denmark)

Andersen, Simon Ivar; Speight, James

2001-01-01

are precipitated, adsorbents are added to the n-pentane solutions of the resins and oils, by which process the resins are adsorbed and subsequently recovered by the use of a more polar solvent, and the oils remain in solution. The resin fraction plays an important role in the stability of petroleum and prevents...... separation of the asphaltene constituents as a separate phase. Indeed, the absence of the resin fraction (produced by a variety of methods) from the maltenes influences the ability of the de-resined maltenes to accommodate the asphaltenes either in solution or as a stable part of a colloidal system. In spite....... Suggestions are also made regarding current thoughts of the role of these constituents on the structure and stability of petroleum....

Anion-exchange resin-based desulfurization process. Final report

Energy Technology Data Exchange (ETDEWEB)

Sheth, A C; Dharmapurikar, R; Strevel, S D

1994-01-01

The following investigations were performed: (1) batch mode screening of eleven(11) commercially available resins and selection of three candidate resins for further evaluation in a fixed-bed setup. (2) Process variables study using three candidate resins in the fixed-bed setup and selection of the ``best`` resin for process economics development. (3) Exhaustion efficiency and solution concentration were found to be inversely related necessitating a trade-off between the resin cost versus the cost of evaporation/concentration of ensuing effluents. (4) Higher concentration of the HCO{sub 3}{sup {minus}} form of active sites over less active CO{sub 3}{sup 2{minus}} form of sites in the resin was believed to be the main reason for the observed increase in the equilibrium capacity of the resin at an elevated static CO{sub 2}-pressure. This Increase in capacity was found to level off around 80--120 psig range. The increase in CO{sub 2}-pressure, however, did not appear to affect the overall ion-exchange kinetics. (5) In the fixed-bed mode, the solution concentration was found to affect the equilibrium capacity of candidate resins. Their relationship was well satisfied by the Langmuir type non-linear equilibrium isotherm. Alternatively, the effect of solution concentration on overall ion-exchange kinetics varied from resin to resin. (6) Product inhibition effect on the resin was observed as an initial increase followed by a significant decrease in the resin`s equilibrium capacity for SO{sub 4}{sup 2{minus}} as the HCO{sub 3}{sup {minus}}/SO{sub 4}{sup 2{minus}} molar ratio in the solution was increased from 0 to 1.0. This ratio, however, did not affect the overall ion-exchange kinetics.

Adsorption of Monobutyl Phthalate from Aqueous Phase onto Two Macroporous Anion-Exchange Resins

Directory of Open Access Journals (Sweden)

Zhengwen Xu

2014-01-01

Full Text Available As new emerging pollutants, phthalic acid monoesters (PAMs pose potential ecological and human health risks. In the present study, adsorption performance of monobutyl phthalate (MBP onto two macroporous base anion-exchange resins (D-201 and D-301 was discussed. It was found that the adsorption isotherms were best fitted by the Langmuir equation while the adsorption kinetics were well described by pseudo-first-order model. Analyses of sorption isotherms and thermodynamics proved that the adsorption mechanisms for DBP onto D-201 were ion exchange. However, the obtained enthalpy values indicate that the sorption process of MBP onto D-301 is physical adsorption. The equilibrium adsorption capacities and adsorption rates of DBP on two different resins increased with the increasing temperature of the solution. D-301 exhibited a higher adsorption capacity of MBP than D-201. These results proved that D-301, as an effective sorbent, can be used to remove phthalic acid monoesters from aqueous solution.

Pilot Plant for treating of spent exchange resins

International Nuclear Information System (INIS)

Iglesias, Alberto M.; Raffo Calderon, Maria del C.; Varani, Jose L.

2004-01-01

Spent exchange resins that have been accumulating during the last operational 30 years in Atucha I nuclear power plant (NPP) are a 'problematic' waste. These spent resins conform an intermediate level waste due to the total content of alpha, beta and gamma emitters (some samples of spent resins were analyzed in 2003). For this reason its treatment is more expensive since it is necessary to add more safety barriers for its final disposition and also for the radioprotection actions that are involved. Using sulfuric acid solutions it is possible to elute from the spent resins the ions that are retained. In the same operation are eluted Cobalt, Cesium and alpha emitters since that all these elements react as cations in aqueous solution. Decontamination by electrochemical methods was analyzed as an interesting method to apply after elution operation to these spent resins since that with the decontamination process it is possible to obtain a solid without activity and concentrate the activity in cells that are small in volume and its manipulation doesn't present any extra complication. Experiments made with active samples taken from the deposit were successful. Because of these results it was built a small plant to treat a batch of 100 dm 3 of wet spent exchange resins. Some problems with the material that was in the deposit together with spent resins caused that we had to plan a more complex strategy to obtain a complete decontamination of the spent resins (in this stage we used the cobalt retention cell that was described in other paper to retain Cobalt and alpha emitters and a sample of zeolites from Argentina ores to retain Cesium). Due to alpha emitters act electrochemically like cations it was possible to retain altogether with ionic Cobalt on the copper amalgam electrode. Working in the non-active lab with alcoholic solutions it was possible to retain ionic Cesium on a copper electrode (copper is covered by mercury fine film which forms a solid amalgam) with a

Determination of 99Tc in fresh water using TRU resin by ICP-MS.

Science.gov (United States)

Guérin, Nicolas; Riopel, Remi; Kramer-Tremblay, Sheila; de Silva, Nimal; Cornett, Jack; Dai, Xiongxin

2017-10-02

Technetium-99 ( 99 Tc) determination at trace level by inductively coupled plasma mass spectrometry (ICP-MS) is challenging because there is no readily available appropriate Tc isotopic tracer. A new method using Re as a recovery tracer to determine 99 Tc in fresh water samples, which does not require any evaporation step, was developed. Tc(VII) and Re(VII) were pre-concentrated on a small anion exchange resin (AER) cartridge from one litre of water sample. They were then efficiently eluted from the AER using a potassium permanganate (KMnO 4 ) solution. After the reduction of KMnO 4 in 2 M sulfuric acid solution, the sample was passed through a small TRU resin cartridge. Tc(VII) and Re(VII) retained on the TRU resin were eluted using near boiling water, which can be directly used for the ICP-MS measurement. The results for method optimisation, validation and application were reported. Crown Copyright © 2017. Published by Elsevier B.V. All rights reserved.

Development of an extractive-scintillating chromatographic resin for the detection of radioactive isotopes

International Nuclear Information System (INIS)

Vincze, A.; Halasz, L.; Solymosi, J.; Molnar, A.; Safrany, A.

2007-01-01

In this paper, the development of a new-type of resin is presented, which contains selective complexing and scintillating molecules in a chemically bonded form. The resin material is produced via radiation polymerization of a solution of 2-(4-allyloxy-phenyl)-5-phenyl oxazole, 5-(allyloxyphenyl)- 2-[4-(5-phenyl-oxazole-2-il)-phenyl] oxazole, diethylene glycol dimethacrylate (DEGMA), styrene and the allyl derivative of a 18C6 crown ether-dicarbolic acid complexing agent. The product is a macroporous polymer matrix that shows fluorescent properties and ion binding capacity excellent for radioanalytical purposes. (author)

Method for loading resin beds

International Nuclear Information System (INIS)

Notz, K.J.; Rainey, R.H.; Greene, C.W.; Shockley, W.E.

1978-01-01

An improved method of preparing nuclear reactor fuel by carbonizing a uranium loaded cation exchange resin provided by contacting a H+ loaded resin with a uranyl nitrate solution deficient in nitrate, comprises providing the nitrate deficient solution by a method comprising the steps of reacting in a reaction zone maintained between about 145 to 200 0 C, a first aqueous component comprising a uranyl nitrate solution having a boiling point of at least 145 0 C with a second aqueous component to provide a gaseous phase containing HNO 3 and a reaction product comprising an aqueous uranyl nitrate solution deficient in nitrate

Removal of sulfamic acid from plutonium sulfamate--sulfamic acid solution

International Nuclear Information System (INIS)

Gray, L.W.

1978-10-01

Plutonium metal can be readily dissolved in aqueous solutions of sulfamic acid. When the plutonium sulfamate--sulfamic acid solutions are added to normal purex process streams, the sulfamate ion is oxidized by addition of sodium nitrite. This generates sodium sulfate which must be stored as radioactive waste. When recovery of ingrown 241 Am or storage of the dissolved plutonium must be considered, the sulfamate ion poses major and undesirable precipitation problems in the process streams. The present studies show that 40 to 80% of the sulfamate present in the dissolver solutions can be removed by precipitation as sulfamic acid by the addition of concentrated nitric acid. Addition of 64% nitric acid allows precipitation of 40 to 50% of the sulfamate; addition of 72% nitric acid allows precipitation of 50 to 60% of the sulfamate. If the solutions are chilled, additional sulfamic acid will precipitate. If the solutions are chilled to -10 0 C, about 70 to 80% of the orginal sulfamic acid in the dissolver will precipitate. A single, low-volume wash of the sulfamic acid crystals with concentrated nitric acid will decontaminate the crystals to a plutonium content of 5 dis/(min-gram)

Influence of the Functionalization Degree of Acidic Ion-Exchange Resins on Ethyl Octyl Ether Formation

Czech Academy of Sciences Publication Activity Database

Guilera, J.; Hanková, Libuše; Jeřábek, Karel; Ramírez, E.; Tejero, J.

2014-01-01

Roč. 78, MAY (2014), s. 14-22 ISSN 1381-5148 Grant - others:SEURDO(ES) CTQ2010-16047 Institutional support: RVO:67985858 Keywords : acidic ion - exchange resin * sulfonation degree * ISEC Subject RIV: CC - Organic Chemistry Impact factor: 2.515, year: 2014

Synthesis of Novel Polymeric Resins by Gamma Irradiation for Separation of In(III) ions from Cd(II) in Aqueous Media

International Nuclear Information System (INIS)

Massoud, A.; Abou El-Nour, F.; Killa, H.

2012-01-01

In this work, Zn(II)polymethacrylates and poly(acrylamide-acrylic acid) were prepared by gamma irradiation polymerization technique of the corresponding monomer at 30 kGy. The polymeric resins were mixed with Indium ions to determine its capacity in aqueous solutions using batch experiment. The adsorption efficiency of obtained polymeric resins toward In(III) and Cd(II) in different experimental conditions was established. Batch and column methods were applied for separation of indium and cadmium. The effects of various eluants such as H 2 SO 4 , NH 4 NO 3 , HNO 3 and HCl on the recovery of both metal ions were studied. The polymeric resins may be regenerated using 3M HCl solutions.

The effect of the conditions of amidoximation on the adsorptive characteristics of amide oxime resin for uranium recovery from seawater

International Nuclear Information System (INIS)

Hori, Takahiro; Furusaki, Shintaro; Sugo, Takanobu; Okamoto, Jiro.

1987-01-01

A hollow-fiber type chelating resin containing the amide oxime group for the recovery of uranium from seawater was synthesized by radiation-induced graft polymerization. The effect of the conditions of amidoximation on the amount and/or distribution of the functional groups and on the durability to the recycle adsorption was investigated. The amount of adsorbed copper on the resin increased with the reaction time of the amidoximation, but that of adsorbed hydrochloric acid gradually decreased after reaching the maximum. From the results of elemental analysis, infrared adsorption spectra, visible light and ultraviolet adsorption spectra and the observation of coloration of the resin by alkaline treatment, the amidoximation was found to be a consecutive reaction. The results also suggested that, after the introduction of the amide oxime group, the acidic amide, hydroxamic acid and/or cyclic functional groups were formed. From the measurement of the distribution of adsorbed copper by X-ray microanalyzer, it was confirmed that the amidoximation occured uniformly across the resin. An experiment was carried out on the recycle adsorption of the amide oxime resin using natural seawater, and the sufficient durability was recognized for the case that the resin was taken out from the hydroxylamine solution at the time when the amount of adsorbed hydrochloric acid reached the maximum. In this case the resin contained the largest amount of the amide oxime group and least amount of the by-products formed from the secondary reactions. (author)

Acetic acid extraction from aqueous solutions using fatty acids

NARCIS (Netherlands)

IJmker, H.M.; Gramblicka, M.; Kersten, Sascha R.A.; van der Ham, Aloysius G.J.; Schuur, Boelo

2014-01-01

A major challenge for production of acetic acid via bio-based routes is cost-effective concentration and purification of the acetic acid from the aqueous solutions, for which liquid–liquid extraction is a possible method. A main challenge in extraction of acetic acid from dilute aqueous solutions is

Biodiesel production from acid oils and ethanol using a solid basic resin as catalyst

International Nuclear Information System (INIS)

Marchetti, J.M.; Errazu, A.F.

2010-01-01

In the search of an alternative fuel to substitute diesel fuel, biodiesel appears as one of the most promising sources of energy for diesel engines because of its environmental advantages and also due to the evolution of the petroleum market. Refined oil is the conventional raw material for the production of this biofuel; however, its major disadvantage is the high cost of its production. Therefore, frying oils, waste oils, crude oils and/or acid oils are being tested as alternative raw materials; nevertheless, there will be some problems if a homogeneous basic catalyst (NaOH) is employed due to the high amount of free fatty acid present in the raw oil. In this work, the transesterification reaction of acid oil using solid resin, Dowex monosphere 550 A, was studied as an alternative process. Ethanol was employed to have a natural and sustainable final product. The reaction temperature's effects, the initial amount of free fatty acid, the molar ratio of alcohol/oil and the type of catalyst (homogeneous or heterogeneous) over the main reaction are analyzed and their effects compared. The results obtained show that the solid resin is an alternative catalyst to be used to produce fatty acid ethyl esters (FAEEs) by a transesterification reaction with a final conversion over 90%. On the other hand, the time required to achieve this conversion is bigger than the one required using conventional technology which employs a homogeneous basic catalyst. This reaction time needs to be optimized. (author)

Properties of the Carboxylate ion exchange resins

International Nuclear Information System (INIS)

Allard, Bert; Dario, Maarten; Boren, Hans; Torstenfelt, Boerje; Puigdomenech, Ignasi; Johansson, Claes

2002-09-01

Weakly acidic, carboxylic resin has been selected, together with strong base anion resins, for water purification at the Forsmark 1 and 2 reactors. For the strong (but not the weak) ion exchange resin the Nuclear Power Inspectorate has given permission to dispose the spent resins in the SFR 1 (the Final Repository for Radioactive Operational Waste). This report gives a review of the carboxylic resins and comes to the conclusion that the resins are very stable and that there should not exist any risks for increased leaching of radionuclides from SFR 1 if these resins are disposed (compared to the strong resins)

Process for hardening an alkyd resin composition using ionizing radiation. [electron beams, gamma radiation

Energy Technology Data Exchange (ETDEWEB)

Watanabe, T; Murata, K; Maruyama, T

1969-11-27

In an alkyd resin composition having free hydroxide radicals and containing a conjugated unsaturated fatty acid and/or oil as a component thereof, a process for hardening an alkyd resin composition comprises the steps of dissolving into a vinyl monomer, the product obtained by the semi-esterification reaction of said hydroxide radicals with acid anhydrides having polymerizable radicals and hardening by ionizing radiation to provide a coating with a high degree of cross-linking, with favorable properties such as toughness, hardness, chemical resistance and resistance to weather and with the feasibility of being applied as the ground and finish coat on metals, wood, paper, outdoor construction or the like. Any kind of ionization radiation, particularly accelerated electron beams, ..gamma.. radiation can be used at 50/sup 0/C to -5/sup 0/C for a few seconds or minutes, permitting continuous operation. In one example, 384 parts of phthalic anhydride, 115 parts of pentaerythritol, 233 parts of trimethylol ethane, 288 parts of tung fatty acid and 49 parts of para-tertiary-butyl benzoic acid are mixed and heated with 60 parts of xylene to an acid value of 12. In addition, 271 parts of maleic anhydride and 0.6 parts of hydroquinone are admixed with the content and heated to terminate the reaction. 100 parts of a 50% stylene solution of this alkyd resin are mixed with 1 part of a 60% toluene solution of cobalt naphthenate, and then coated on a glass plate and irradiated with high energy electron beams of 300 kV with a dose of 5 Mrad for 1 sec.

Preparation of extractive resins for producing terbium-161

International Nuclear Information System (INIS)

De la Cruz B, C. C.; Monroy G, F.

2009-10-01

This paper presents the development of a methodology for extractive resins preparation to base of HDEHP, which allows to separation of Tb from Gd generating an own technology of preparation of these resins. The study included the extractive resins preparation from 6 different supports: kieselguhr Dg, alumina, red volcanic rock, chiluca, quarry and fluorite; two treatment types of of supports and varied concentrations of HDEHP extractant (di(2-etil hexyl) orthophosphoric acid), in order to determine which resin has improved efficiency of Gd and Tb separation, and radionuclide purity of 161 Tb. Resins were prepared to base of kieselguhr to determine the most appropriate silicon deposition process. Two silicon deposition treatments were realized: treatment I , by contact with silicon deposition solution (dimethyldichlorosilane / heptane 1:30) and treatment II by contact with vapors of dimethyldichlorosilane in vacuum. The extractant retention was carried out to different concentrations of HDEHP / acetone: 1:4, 1:8, 1:15, 1:20, 1:30 and 1:40. According to the results, there is not direct relation of HDEHP concentration used in extractive resins preparation to base of kieselguhr over the efficiency of Gd and Tb separation and of radionuclide purity of 161 Tb. The effect of support in the efficiency of Gd and Tb separation was studied to prepare resins with the supports kieselguhr, alumina, quarry, chiluca, volcanic rock and fluorite, using the silicon deposition treatment II for the supports and a concentration of HDEHP / acetone 1:20, for extractant retention. Only resins based on kieselguhr could separate to Gd from Tb quantitatively, the resin at a concentration of HDEHP / Acetone 1:20 was the best results obtained in Gd and Tb separation, achieving a separation efficiency greater than 90% and a radionuclide purity higher than 99%. (Author)

Post-irradiation hardness of resin-modified glass ionomer cements and a polyacid-modified composite resin

International Nuclear Information System (INIS)

Yap, A.U.J.

1997-01-01

This study examined the post-irradiation hardness of resin-modified glass ionomer cements and a polyacid-modified composite resin using a digital microhardness tester. Change in hardness of these materials over a period of 6 months was compared to that of conventional glass ionomer cements and a composite resin. With the exception of the composite resin, all materials showed a significant increase in hardness over 24 h after their initial set. Dual-cure resin-modified glass ionomer cements showed decreased hardness with increased storage time in saline at 37 o C. Results suggest that the addition of resins to glass ionomer cements does not improve initial hardness and does not negate the acid-base reaction of conventional cements. Resin addition may, however, lead to increased water sorption and decreased hardness. (author)

Removal of nitrate from ammonium hydroxide solution containing organics by ion exchange method

International Nuclear Information System (INIS)

Venugopal Chetty, K.; Gamare, Jayashree S.; Vaidya, V.N.

2004-01-01

Removal of nitrate from ammonium hydroxide solution containing HMTA (hexamethyltetramine) and Urea was studied using indigenously available anion exchange resins. This type of waste is produced during nuclear fuel preparation by internal gelation process. The resins used are Tulsion A-27(MP) and Duolite A. 102D. The time of equilibration and capacity of the resins were determined from distribution ratios obtained by equilibrating resin with nitrate solution. The loading, washing and elution behavior of nitrate on these resins were studied using synthetic mixture having similar composition of the waste produced. Elution studies were carried out using sodium hydroxide, hydrochloric acid and ammonium chloride. The studies were also carried out at higher temperature of around 60 degC. The data was compared with that obtained using Dowex 1x4 for the same purpose. (author)

Multi-podant diglycolamides and room temperature ionic liquid impregnated resins: An excellent combination for extraction chromatography of actinides.

Science.gov (United States)

Gujar, R B; Ansari, S A; Verboom, W; Mohapatra, P K

2016-05-27

Extraction chromatography resins, prepared by impregnating two multi-podant diglycolamide ligands, viz. diglycolamide-functionalized calix[4]arene (C4DGA) and tripodal diglycolamide (T-DGA) dissolved in the room temperature ionic liquid 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)amide (RTIL: C4mimTf2N) on Chromosorb-W (an inert solid support), gave excellent results for the removal of trivalent actinides from acidic waste solutions. Distribution coefficient measurements on several metal ions showed selective sorption of Am(III) over hexavalent uranyl ions and other fission product elements such as strontium and cesium. The sorbed metal ions could be efficiently desorbed with a complexing solution containing guanidine carbonate and EDTA buffer. The sorption of Am(III) on both resins followed pseudo-second order rate kinetics with rate constants of 1.37×10(-6) and 6.88×10(-7)g/cpmmin for T-DGA and C4DGA resins, respectively. The metal sorption on both resins indicated the Langmuir monolayer chemisorption phenomenon with Eu(III) sorption capacities of 4.83±0.21 and 0.52±0.05mg per g of T-DGA and C4DGA resins, respectively. The results of column studies show that these resins are of interest for a possible application for the recovery of hazardous trivalent actinides from dilute aqueous solutions. Copyright © 2016 Elsevier B.V. All rights reserved.

Concentration and purification of plutonium solutions by means of ion-exchange columns

Energy Technology Data Exchange (ETDEWEB)

Durham, R W; Aikin, A M

1953-02-15

Equilibrium experiments using Dowex 50 ion-exchange resin and nitric acid solutions of Pu{sup 3+}, UO{sub 2}{sup 2+}, Fe{sup 2+} cations have yielded values for the absorption affinities for these ions. Trivalent plutonium was found to be far more strongly absorbed than UO{sub 2}{sup 2+} and Fe{sup 2+}. Column studies have shown that uranium can be completely separated from plutonium even when the initial concentration of uranium is very much greater than that of the plutonium. A plutonium concentration increase of about fifty-fold can be obtained from solutions about 10{sup -3} M in plutonium and 1.0M in nitric acid. The equation K{sub Pu}{sup 3+} = X{sub R} (1-X{sub S}){sup 3} C{sub S}{sup 2}/X{sub S} (1-X{sub R}){sup 3} C{sub R}{sup 2} for estimating the maximum amount of plutonium taken up by a column of resin of unit volume from a solution of total equivalent concentration, C{sub S} , has been shown to hold for values of C{sub S} up to 3 equivalents per litre. X{sub R}, the equivalent fraction of plutonium on the resin, is the number of equivalents of plutonium absorbed by the resin divided by the total capacity of the column. X{sub S}, the equivalent fraction of plutonium in solution, is the equivalent concentration of plutonium divided by the total equivalent concentration of cations in solution. C{sub R} is the total capacity of the resin in milli-equivalents per gram of dry resin. Recommendations have been made for the application and operation of ion-exchange columns in the Plutonium-Extraction Plant. (author)

Improved production and processing of 89Zr using a solution target

International Nuclear Information System (INIS)

Pandey, Mukesh K.; Bansal, Aditya; Engelbrecht, Hendrik P.; Byrne, John F.; Packard, Alan B.; DeGrado, Timothy R.

2016-01-01

Objective: The objectives of the present work were to improve the cyclotron production yield of 89 Zr using a solution target, develop a practical synthesis of the hydroxamate resin used to process the target, and develop a biocompatible medium for 89 Zr elution from the hydroxamate resin. Methods: A new solution target (BMLT-2) with enhanced heat dissipation capabilities was designed by using helium-cooled dual foils (0.2 mm Al and 25 μ Havar) and an enhanced water-cooled, elongated solution cavity in the target insert. Irradiations were performed with 14 MeV protons on a 2 M solution of yttrium nitrate in 1.25 M nitric acid at 40-μA beam current for 2 h in a closed system. Zirconium-89 was separated from Y by use of a hydroxamate resin. A one-pot synthesis of hydroxamate resin was accomplished by activating the carboxylate groups on a carboxymethyl cation exchange resin using methyl chloroformate followed by reaction with hydroxylamine hydrochloride. After trapping of 89 Zr on hydroxamate resin and rinsing the resin with HCl and water to release Y, 89 Zr was eluted with 1.2 M K 2 HPO 4 /KH 2 PO 4 buffer (pH 3.5). ICP-MS was used to measure metal contaminants in the final 89 Zr solution. Results: The BMLT-2 target produced 349 ± 49 MBq (9.4 ± 1.2 mCi) of 89 Zr at the end of irradiation with a specific activity of 1.18 ± 0.79 GBq/μg. The hydroxamate resin prepared using the new synthesis method showed a trapping efficiency of 93% with a 75 mg resin bed and 96–97% with a 100–120 mg resin bed. The elution efficiency of 89 Zr with 1.2 M K 2 HPO 4 /KH 2 PO 4 solution was found to be 91.7 ± 3.7%, compared to > 95% for 1 M oxalic acid. Elution with phosphate buffer gave very small levels of metal contaminants: Al = 0.40–0.86 μg (n = 2), Fe = 1.22 ± 0.71 μg (n = 3), Y = 0.29 μg (n = 1). Conclusions: The BMLT-2 target allowed doubling of the beam current for production of 89 Zr, resulting in a greater than 2-fold increase in production yield in comparison

Eichrom's ABEC trademark resins: Alkaline radioactive waste treatment, radiopharmaceutical, and potential hydrometallurgical applications

International Nuclear Information System (INIS)

Bond, A.H.; Gula, M.J.; Chang, F.; Rogers, R.D.

1997-01-01

Eichrom's ABEC trademark resins selectivity extract certain anions from high ionic strength acidic, neutral, or strongly alkaline media, and solute stripping can be accomplished by eluting with water. ABEC resins are stable to pH extreme and radiolysis and operate in high ionic strength and/or alkaline solutions where anion-exchange is often ineffective. Potential applications of the ABEC materials include heavy metal and ReO 4 - separations in hydrometallurgy and purification of perrhenate iodide, and iodate in radiopharmaceutical production. Separation of 99m TcO 4 - from its 99 MoO 4 2- parent and stripping with water or physiological saline solution have been demonstrated for radiopharmaceutical applications. Removal of 99 TcO 4 - and 129 I - from alkaline tank wastes has also been successfully demonstrated. The authors will discuss the scale-up studies, process-scale testing, and market development of this new extraction material

Labile synthetic cadmium complexes are not bioavailable to Pseudokirchneriella subcapitata in resin buffered solutions

Energy Technology Data Exchange (ETDEWEB)

Verheyen, L., E-mail: Liesbeth.Verheyen@ees.kuleuven.be [Division of Soil and Water Management, K.U. Leuven, Kasteelpark Arenberg 20, Box 2459, 3001 Heverlee (Belgium); Merckx, R. [Division of Soil and Water Management, K.U.Leuven, Kasteelpark Arenberg 20, Box 2459, 3001 Heverlee (Belgium); Smolders, E., E-mail: Erik.Smolders@ees.kuleuven.be [Division of Soil and Water Management, K.U. Leuven, Kasteelpark Arenberg 20, Box 2459, 3001 Heverlee (Belgium)

2012-11-15

The Free Ion Activity Model (FIAM) predicts that cadmium (Cd) uptake by organisms is identical for solutions with the same free Cd{sup 2+} concentration and inorganic composition. Clear exceptions to the FIAM have been shown for Cd uptake by plant roots, periphyton and human cells where labile Cd complexes increase bioavailability and which has been attributed to their role in enhancing Cd diffusion towards the uptake cells. Here, we assessed the role of labile Cd complexes on Cd uptake by algae, for which diffusion limitations should be less pronounced due to their smaller size. Long-term (3 days) Cd uptake by the green algae Pseudokirchneriella subcapitata was measured in resin buffered solutions with or without synthetic ligands and at three Cd{sup 2+} ion activities (pCd 8.2-5.7). The free Cd{sup 2+} activity was maintained during the test using a metal-selective resin located in the algal bottles. Total dissolved Cd increased up to 35-fold by adding the synthetic ligands at constant Cd{sup 2+} activity. In contrast, Cd uptake by algae increased maximally 2.8 fold with increasing concentration of the synthetic ligands and the availability of the complexes were maximally 5.2% relative to Cd{sup 2+} for NTA and CDTA complexes. It is concluded that labile Cd complexes do not greatly enhance Cd bioavailability to the unicellular algae and calculations suggest that Cd transport from solution to these small cells is not rate limiting.

Labile synthetic cadmium complexes are not bioavailable to Pseudokirchneriella subcapitata in resin buffered solutions

International Nuclear Information System (INIS)

Verheyen, L.; Merckx, R.; Smolders, E.

2012-01-01

The Free Ion Activity Model (FIAM) predicts that cadmium (Cd) uptake by organisms is identical for solutions with the same free Cd 2+ concentration and inorganic composition. Clear exceptions to the FIAM have been shown for Cd uptake by plant roots, periphyton and human cells where labile Cd complexes increase bioavailability and which has been attributed to their role in enhancing Cd diffusion towards the uptake cells. Here, we assessed the role of labile Cd complexes on Cd uptake by algae, for which diffusion limitations should be less pronounced due to their smaller size. Long-term (3 days) Cd uptake by the green algae Pseudokirchneriella subcapitata was measured in resin buffered solutions with or without synthetic ligands and at three Cd 2+ ion activities (pCd 8.2–5.7). The free Cd 2+ activity was maintained during the test using a metal-selective resin located in the algal bottles. Total dissolved Cd increased up to 35-fold by adding the synthetic ligands at constant Cd 2+ activity. In contrast, Cd uptake by algae increased maximally 2.8 fold with increasing concentration of the synthetic ligands and the availability of the complexes were maximally 5.2% relative to Cd 2+ for NTA and CDTA complexes. It is concluded that labile Cd complexes do not greatly enhance Cd bioavailability to the unicellular algae and calculations suggest that Cd transport from solution to these small cells is not rate limiting.

Selective extraction of U(VI), Th(IV), and La(III) from acidic matrix solutions and environmental samples using chemically modified Amberlite XAD-16 resin

Energy Technology Data Exchange (ETDEWEB)

Prabhakaran, D.; Subramanian, M.S. [Department of Chemistry, Indian Institute of Technology, 600 036, Chennai (India)

2004-06-01

A new grafted polymer has been developed by the chemical modification of Amberlite XAD-16 (AXAD-16) polymeric matrix with [(2-dihydroxyarsinoylphenylamino)methyl]phosphonic acid (AXAD-16-AsP). The modified polymer was characterized by a combination of {sup 13}C CPMAS and {sup 31}P solid-state NMR, Fourier transform-NIR-FIR-Raman spectroscopy, CHNPS elemental analysis, and thermogravimetric analysis (TGA). The distribution studies for the extraction of U(VI), Th(IV), and La(III) from acidic solutions were performed using an AXAD-16-AsP-packed chromatographic column. The influences of various physiochemical parameters on analyte recovery were optimized by both static and dynamic methods. Accordingly, even under high acidities (>4 M), good distribution ratio (D) values (10{sup 2}-10{sup 4}) were achieved for all the analytes. Metal ion desorption was effective using 1 mol L{sup -1} (NH{sub 4}){sub 2}CO{sub 3}. From kinetic studies, a time duration of <15 min was sufficient for complete metal ion saturation of the resin phase. The maximum metal sorption capacities were found to be 0.25, 0.13, and 1.49 mmol g{sup -1} for U(VI); 0.47, 0.39, and 1.40 mmol g{sup -1} for Th(IV); and 1.44, 1.48, and 1.12 mmol g{sup -1} for La(III), in the presence of 2 mol L{sup -1} HNO{sub 3}, 2 mol L{sup -1} HCl, and under pH conditions, respectively. The analyte selectivity of the grafted polymer was tested in terms of interfering species tolerance studies. The system showed an enrichment factor of 365, 300, and 270 for U(VI), Th(IV), and La(III), and the limit of analyte detection was in the range of 18-23 ng mL{sup -1}. The practical applicability of the polymer was tested with synthetic nuclear spent fuel and seawater mixtures, natural water, and geological samples. The RSD of the total analytical procedure was within 4.9%, thus confirming the reliability of the developed method. (orig.)

Novel silica-based ion exchange resin

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-11-01

Eichrom`s highly successful Diphonixo resin resembles a conventional ion exchange resin in its use of sulfonic acid ligands on a styrene- divinylbenzene matrix. Diphonix resin exhibits rapid exchange kinetics that allow economical operation of ion exchange systems. Unlike conventional resins, Diphonix resin contains chelating ligands that are diphosphonic acid groups that recognize and remove the targeted metals and reject the more common elements such as sodium, calcium and magnesium. This latter property makes Diphonix ideal for many industrial scale applications, including those involving waste treatment. For treatment of low-level, transuranic (TRU) and high- level radioactive wastes, Diphonix`s polystyrene backbone hinders its application due to radiolytic stability of the carbon-hydrogen bonds and lack of compatibility with expected vitrification schemes. Polystyrene-based Diphonix is approximately 60% carbon- hydrogen. In response to an identified need within the Department of Energy for a resin with the positive attributes of Diphonix that also exhibits greater radiolytic stability and final waste form compatibility, Eichrom has successfully developed a new, silica-based resin version of Diphonix. Target application for this new resin is for use in environmental restoration and waste management situations involving the processing of low-level, transuranic and high-level radioactive wastes. The resin can also be used for processing liquid mixed waste (waste that contains low level radioactivity and hazardous constituents) including mixed wastes contaminated with organic compounds. Silica-based Diphonix is only 10% carbon-hydrogen, with the bulk of the matrix silica.

Pengaruh Minuman Kopi terhadap Perubahan Warna pada Resin Komposit

Directory of Open Access Journals (Sweden)

Aprilia Aprilia

2015-10-01

Full Text Available Objective: The aim of this research was to investigate the influence of coffee beverage on hybrid composite resin discoloration. Material and method: This study used hybrid composite resin with A3 color, and was done by soaking composite resin plates in coffee solution for 1, 3, 5, and 7 days, corresponding to equivalent coffee usage for 6 months, 1, 1.5, and 2 years. The same measurements of reflectance were done before and after soaking into coffee solution. In the measurement, a beam from He-Ne laser is reflected by the sample to a photovoltaic cell type BOY-47, which provides a voltage signal accordig to the intensity of reflected light. Results: There was a significant difference between composite resin plates before and after soaking into coffee dilution for 1, 3, 5, and 7 days. Conclusion: Composite resin is discolored after soaking into a coffee solution, suggesting that coffee usage will have a discoloring effect on dental composite resin.

Improved production and processing of ⁸⁹Zr using a solution target.

Science.gov (United States)

Pandey, Mukesh K; Bansal, Aditya; Engelbrecht, Hendrik P; Byrne, John F; Packard, Alan B; DeGrado, Timothy R

2016-01-01

The objectives of the present work were to improve the cyclotron production yield of (89)Zr using a solution target, develop a practical synthesis of the hydroxamate resin used to process the target, and develop a biocompatible medium for (89)Zr elution from the hydroxamate resin. A new solution target (BMLT-2) with enhanced heat dissipation capabilities was designed by using helium-cooled dual foils (0.2 mm Al and 25 μ Havar) and an enhanced water-cooled, elongated solution cavity in the target insert. Irradiations were performed with 14 MeV protons on a 2M solution of yttrium nitrate in 1.25 M nitric acid at 40-μA beam current for 2 h in a closed system. Zirconium-89 was separated from Y by use of a hydroxamate resin. A one-pot synthesis of hydroxamate resin was accomplished by activating the carboxylate groups on a carboxymethyl cation exchange resin using methyl chloroformate followed by reaction with hydroxylamine hydrochloride. After trapping of (89)Zr on hydroxamate resin and rinsing the resin with HCl and water to release Y, (89)Zr was eluted with 1.2 M K2HPO4/KH2PO4 buffer (pH3.5). ICP-MS was used to measure metal contaminants in the final (89)Zr solution. The BMLT-2 target produced 349±49 MBq (9.4±1.2 mCi) of (89)Zr at the end of irradiation with a specific activity of 1.18±0.79 GBq/μg. The hydroxamate resin prepared using the new synthesis method showed a trapping efficiency of 93% with a 75 mg resin bed and 96-97% with a 100-120 mg resin bed. The elution efficiency of (89)Zr with 1.2M K2HPO4/KH2PO4 solution was found to be 91.7±3.7%, compared to >95% for 1 M oxalic acid. Elution with phosphate buffer gave very small levels of metal contaminants: Al=0.40-0.86 μg (n=2), Fe=1.22±0.71 μg (n=3), Y=0.29 μg (n=1). The BMLT-2 target allowed doubling of the beam current for production of (89)Zr, resulting in a greater than 2-fold increase in production yield in comparison with a conventional liquid target. The new one-pot synthesis of hydroxamate

Tests of a Higgins contactor for the engineering-scale resin loading of uranium

International Nuclear Information System (INIS)

Spence, R.D.; Haas, P.A.

1978-01-01

The loading of uranium on weak-acid ion exchange resin is a basic step in the production of fuel particles for high-temperature gas-cooled reactors (HTGRs). In the work reported here, an engineering-scale continuous resin loader (2-in.-ID Higgins contactor) was tested with existing engineering-scale process equipment. The Higgins contactor was first successfully used to convert Na + -form resin to the H + -form; then it was evaluated as a uranium loader. Results show that the 2-in.-ID Higgins contactor can easily load 25 kg of uranium per day, indicating that a 4-in.-ID contactor could load 100 kg/day. Process control was achieved by monitoring and controlling the density, pH, and inventory volume of the uranium feed solution. This control scheme is amenable to remote operation

JASPAS programme task JC-4: Isotopic and isotope dilution analysis of spent fuel solutions by resin bead mass spectrometry

International Nuclear Information System (INIS)

Hayashi, N.; Terakado, S.; Kuno, Y.

1988-05-01

The use of resin beads for mass spectrometry of U and Pu has been extensively developed at Oak Ridge National Laboratory in the USA and tested in a number of intercomparison experiments between the Safeguards Analytical Laboratory (SAL) of the IAEA and the Power Reactor and Fuel Development Corporation (PNC) - Tokai Reprocessing Plant (TRP) in Japan. Resin beads represent a convenient way to concentrate the U and Pu in spent fuel dissolver solution samples from reprocessing facilities, with the added advantage that fission product elements and other actinides such as Am are removed. Measurements on the resin bead samples at SAL were performed on the ORNL-designed 2-Stage Mass Spectrometer. For the dried tracer samples, the U measurements were obtained on the VG54E instrument and the Pu results were obtained with the Finnigan MAT 261 of SAL. PNC/TRP used a VG54 mass spectrometer and obtained their mass fractionation correction factor for the resin bead measurements from the mixed tracer plus chemical standard resin bead samples. The Safeguards Laboratory (NMCC) used their MAT 260 instrument and obtained the fractionation correction factor from resin bead standards provided with the TIGR-82 programme. Both PNC/TRP and NMCC reported problems with obtaining a sufficient ion beam intensity with the resin bead samples. This problem was overcome by both labs and further improvements in the loading and measurement techniques can be expected to yield even better results. It has been demonstrated that the resin bed sampling method can provide results of sufficient quality for safeguards purposes. 2 refs, 3 figs, 16 tabs

21 CFR 173.25 - Ion-exchange resins.

Science.gov (United States)

2010-04-01

..., distilled water and 10 percent ethanol, when, following washing and pretreatment of the resin in accordance... paragraph (a)(18) of this section is used to treat aqueous sugar solutions subject to the condition that the temperature of the sugar solution passing through the resin bed is maintained at 82 °C (179.6 °F) or less and...

Determination of airborne, volatile amines from polyurethane foams by sorption onto a high-capacity cation-exchange resin based on poly(succinic acid).

Science.gov (United States)

Seeber, G; Buchmeiser, M R; Bonn, G K; Bertsch, T

1998-06-05

A high-capacity carboxylic acid-functionalized resin prepared by ring-opening metathesis polymerization based on cross-linked endo,endo-poly(norborn-2-ene-5,6-dicarboxylic acid) was used for the sampling of volatile, airborne amines from polyurethane (PU) foams. Six tertiary amines which represent commonly used promotors for the formation of PUs from diisocyanates and polyols, namely pentamethyldiethylenetriamine, diazabicyclooctane, N-methylmorpholine, N-ethylmorphine, 1,4-dimethylpiperazine and N,N-dimethylethanolamine, were sorbed onto the new resin. The sorption behavior of the new material was investigated in terms of loading capacities, the influence of concentration, flow-rate as well as of the amount of resin. Breakthrough curves were recorded from each single component as well as of mixtures thereof. Finally, the resin was used for the sampling of amines evaporating from PU foams applied in buildings. Further information about time dependent concentration profiles were obtained using a combination of GC-MS and Fourier transform IR spectroscopy.

Fixation and separation of the elements thorium and uranium using anion exchange resins in nitrate solution

International Nuclear Information System (INIS)

Korgaonkar, V.

1967-10-01

The exchange of thorium and uranium between a strong base anion resin and a mixed water + ethanol solvent containing nitrate ions is studied. It is assumed that in the resin the thorium and uranium are fixed in the form of the complexes Th(NO 3 ) 6 2- and UO 2 (NO 3 ) 4 2- in solution these elements are present in the form of complexes having the general formula: Th(NO 3 ) 6-n n-2 and UO 2 (NO 3 ) 4-n n-2 It has been possible to deduce a law for the changes in the partition functions of thorium and uranium as a function of the concentrations of the various species in solution and of the complexing ion NO 3 . From this has been deduced the optimum operational conditions for separating a mixture of these two elements. Finally, in these conditions, the influence of a few interfering ions has been studied: Ba, Bi, Ce, La, Mo, Pb, Zr. The method proposed can be used either as a preparation, or for the dosage of thorium by a quantitative separation. (author) [fr

Gas chromatographic determination of organic acids from fruit juices by combined resin mediated methylation and extraction in supercritical carbon dioxide.

Science.gov (United States)

Barden, T J; Croft, M Y; Murby, E J; Wells, R J

1997-10-17

A procedure in which anionic analytes, trapped on ion exchange resin, are simultaneously methylated and released using methyl iodide in either supercritical carbon dioxide or acetonitrile has been extended to polyfunctional organic acids. The combined SFE methylation of fruit juice acids trapped onto ion exchange resin proceeds in good yield producing the methyl esters of fumaric, succinic, malic, tartaric, isocitric and citric acids which are readily separated by GC. Using this procedure low concentrations of one acid can be detected and quantitated in the presence of very high concentrations of another. This new method detects tartaric acid at levels of 10 ppm in juices containing 10,000 ppm citric acid. Quantitation was performed either by using GC-FID with triethyl citrate or diethyl tartrate as internal standards or with the element specific calibration capability of the GC-AED. A simple new technique for the determination of citric/isocitric acid ratio is now available. Also, in contrast to HPLC methods, the identity of an analyte is readily confirmed by GC-MS.

Corrosion Performance of Nano-ZrO₂ Modified Coatings in Hot Mixed Acid Solutions.

Science.gov (United States)

Xu, Wenhua; Wang, Zhenyu; Han, En-Hou; Wang, Shuai; Liu, Qian

2018-06-01

A nano-ZrO₂ modified coating system was prepared by incorporation of nano-ZrO₂ concentrates into phenolic-epoxy resin. The corrosion performance of the coatings was evaluated in hot mixed acid solution, using electrochemical methods combined with surface characterization, and the effects of nano-ZrO₂ content were specially focused on. The results showed that 1% and 3% nano-ZrO₂ addition enhanced the corrosion resistance of the coatings, while 5% nano-ZrO₂ addition declined it. The coating with 3% nano-ZrO₂ presented the minimum amount of species diffusion, the lowest average roughness (5.94 nm), and the highest C/O ratio (4.55) and coating resistance, and it demonstrated the best corrosion performance among the coating specimens.

Determination of 3-chloro-1,2-propanediol in polyamideamine epichlorohydrin resin solution by reaction-based headspace gas chromatography.

Science.gov (United States)

Yan, Ning; Wan, Xiao-Fang; Chai, Xin-Sheng; Chen, Run-Quan

2018-04-01

We report on a headspace gas chromatographic method for determining the content of 3-chloro-1,2-propanediol in polyamideamine epichlorohydrin resin solution. It was based on quantitatively converting 3-chloro-1,2-propanediol to formaldehyde by periodate oxidation in a closed headspace sample vial at a room temperature for 10 min, and then to methanol by borohydride reduction at 90°C for 40 min followed by the headspace gas chromatographic measurement. The results showed that the present method has an excellent measurement precision (relative standard deviation < 2.60%) and accuracy (recoveries from 96.4-102%) in 3-chloro-1,2-propanediol analysis. The limit of quantitation was 0.031 mg/mL. It is simple and suitable for determining the 3-chloro-1,2-propanediol content in polyamideamine epichlorohydrin resin solution. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

COMPARATIVE STUDY OF THE SHEAR BOND STRENGTH OF COMPOSITE RESIN TO DENTAL ENAMEL CONDITIONED WITH PHOSPHORIC ACID OR Nd: YAG LASER

Directory of Open Access Journals (Sweden)

EDUARDO Carlos de Paula

1997-01-01

Full Text Available This study has been focused on a comparison between the shear bond strength of a composite resin attached to dental enamel surface, after a 35% phosphoric acid etching and after a Nd:YAG laser irradiation with 165.8 J/cm2 of energy density per pulse. After etching and attaching resin to these surfaces, the specimens were thermocycled and then underwent the shearing bond strength tests at a speed of 5 mm/min. The results achieved, after statistical analysis with Student's t-test, showed that the adhesion was significantly greater in the 35% phosphoric acid treated group than in the group treated with the Nd:YAG laser, thus demonstrating the need for developing new studies to reach the ideal parameters for an effective enamel surface conditioning as well as specific adhesives and composite resins when Nd:YAG laser is used

T/sub 4/ radioimmunoassay with ion-exchange resin separation

Energy Technology Data Exchange (ETDEWEB)

Michael, J D; Modha, K [Hoechst Pharmaceuticals Research Ltd., Milton Keynes (UK)

1977-05-28

An explanation is provided for the reports of falsely low values of serum-thyroxine (T/sub 4/) measured by radioimmunoassay (RIA), particularly in sera containing raised concentrations of thyroxine-binding globulin (TBG) (Burr, W.A., Evans, S.E., Hogan, T.C., 1977, Lancet, April 2, 757). A re-examination of the assay technique used in commercial RIA kits ('RIA-gnost T/sub 3/' and 'RIA-gnost T/sub 4/', Behring Diagnostics) showed that blocking of binding proteins by 8-anilino-1-naphthalene sulphonic acid (ANS) was incomplete in sera with raised TBG levels. Spectroscopic determination of the blocker concentration during the time the solution was in contact with the ion exchange resin showed that 98% of the ANS was removed from solution by 10 min contact with the resin, yet 60 min was required to absorb the free T/sub 4/. There was therefore ample time for unblocked TBG to recombine with free T/sub 4/ which was then misclassified as antibody-bound T/sub 4/. The assay technique used in the kits was therefore modified. The less polar TBG blocking agent, ethylmercurithiosalicylate (merthiolate), replaced ANS and it was demonstrated that accurate T/sub 3/ and T/sub 4/ measurements in high TBG sera could be made by resin-separation RIA without resorting to prior denaturation or alcohol extraction.

Transformation of thorium sulfate in thorium nitrate by ion exchange resin

International Nuclear Information System (INIS)

Pereira, W.

1991-01-01

A procedure for transforming thorium sulfate into thorium nitrate by means of a strong cationic ion exchanger is presented. The thorium sulfate solution (approximately 15 g/L Th (SO 4 ) 2 ) is percolate through the resin and the column is washed first with water, with a 0,2 M N H 4 OH solution and then with a 0.2 M N H 4 NO 3 solution in order to eliminate sulfate ion. Thorium is eluted with a 2 M solution of (N H 4 ) 2 CO 3 . This eluate is treated with a solution of nitric acid in order to obtain the complete transformation into Th (NO 3 ) 4 . The proposed procedure leads to good quality thorium nitrate with high uranium decontamination. (author)

Ontario Hydro Research Division's program for treatment of spent ion-exchange resins

International Nuclear Information System (INIS)

Nott, B.R.; Dodd, D.J.R.

1981-09-01

A brief review of the evolution of work programmes for chemical treatment of spent ion-exchange resins in Ontario Hydro's Research Division is presented. Attention has been focussed on pre-treatment processes for the treatment of the spent resins prior to encapsulation of the products in solid matrices. Spent Resin Regeneration and Acid Stripping processes were considered in some detail. Particular attention was paid to carbon-14 on spent resins, its determination in and removal from the spent resins (with the acid stripping technique). The use of separate cation and anion resin beds instead of mixed bed resins was examined with a view to reducing the volume of resin usage and consequently the volume of waste radioactive ion-exchange resin generated. (author)

Irradiation effects in the storage and disposal of radioactive ion-exchange resins

International Nuclear Information System (INIS)

Swyler, K.J.; Dodge, C.E.; Dayal, R.; Weiss, A.J.

1982-01-01

Research is under way to characterize the effects of self-irradiation on radwastes which may be generated when organic ion-exchange media are used in water demineralization or decontamination operations at nuclear facilities. External factors affecting the relation between laboratory evaluations and field performance are emphasized. Initial experiments do not yet indicate substantial radiation dose-rate effects on radiolytic gas yields or acid product formation, when (fully swollen) sulfonic acid resins are irradiated in a sealed air environment. At the same time, oxygen gas is removed from the environment of irradiated resins. Interaction between mild steel coupons and acidic species produced in the irradiation induced decomposition of sulfonic acid resin results in irradiation enhanced corrosion. Corrosion rates depend on radiation dose rate, moisture content and resin chemical loading. In some cases, corrosion rates decrease with time, suggesting depletion of acidic species within the resin bed, or a synergistic interaction between resin and corrosion coupon. Implications of these and other results on evaluating field behavior of radwaste containing ion-exchange media are discussed. 4 figures, 2 tables

Radioluminescence of polyester resin modified with acrylic acid and its salts

Science.gov (United States)

Szalińska, H.; Wypych, M.; Pietrzak, M.; Szadkowska-Nicze, M.

Polimal-109 polyester resin and its compounds containing acrylic acid and its salts such as: sodium, potassium, magnesium, calcium, barium, iron, cobalt, copper and manganese acrylates were studied by the radioluminescence method, including isothermal luminescence (ITL) at a radiation temperature of 77 K, thermoluminescence (RTL) and spectral distributions of isothermal luminescence. Measurements of optical absorption at 77 K before and after irradiation of the investigated samples were also carried out. The results obtained have shown that metal ions play a significant part in the processes taking place in the polyester matrix under the influence of γ 60Co radiation.

Radioluminescence of polyester resin modified with acrylic acid and its salts

International Nuclear Information System (INIS)

Szalinska, H.; Wypych, M.; Pietrzak, M.; Szadkowska-Nicze, M.

1987-01-01

Polimal-109 polyester resin and its compounds containing acrylic acid and its salts such as: sodium, potassium, magnesium, calcium, barium, iron, cobalt, copper and manganese acrylates were studied by the radioluminescence method, including isothermal luminescence (ITL) at a radiation temperature of 77 K, thermoluminescence (RTL) and spectral distributions of isothermal luminescence. Measurements of optical absorption at 77K before and after irradiation of the investigated samples were also carried out. The results obtained have shown that metal ions play a significant part in the processes taking place in the polyester matrix under the influence of γ 60 Co radiation. (author)

Characterization of hydroxybenzoic acid chelating resins: equilibrium, kinetics, and isotherm profiles for Cd(II and Pb(II uptake

Directory of Open Access Journals (Sweden)

BHAVNA A. SHAH

2011-06-01

Full Text Available Chelating ion-exchange resins were synthesized by polycondensation of ortho/para hydroxybenzoic acid with resorcinol/catechol employing formaldehyde as cross-linking agent at 80±5 °C in DMF. The resins were characterized by FTIR and XRD. The uptake behaviour of synthesized resins for Cd(II and Pb(II ions have been studied depending on contact time, pH, metal ion concentration and temperature. The sorption data obtained at optimized conditions were analyzed by the Langmuir and Freundlich isotherms. Experimental data of all metal–resin system were best represented by the Freundlich isotherm. The maximum obtained sorption capacity for cadmium was 69.53 mg g-1 and 169.32 mg g-1 for Lead. The adsorption process follows first order kinetics and the specific rate constant Kr was obtained by the application of the Lagergan equation. Thermodynamic parameters ∆Gads, ∆Sads and ∆Hads were calculated for the metal–resin systems. The external diffusion rate constant (KS and the intra-particle diffusion rate constant (Kid were calculated by the Spahn–Schlunder and Weber–Morris models, respectively. The sorption process was found to follow an intra-particle diffusion phenomenon.

Radiocesium Removal From Synthetic Steam-Generator Cleaning Solutions. Vol. 1

Energy Technology Data Exchange (ETDEWEB)

Narbutt, H; Bartos, B [Department of Radiochemistry, Institute of Nuclear Chemistry and Technology, PL-03185 Warsaw (Poland); Taleb, H [On leave from Tajoura Nuclear Research Center, Tripoli (Libyan Arab Jamahiriya)

1996-03-01

Adjustment of {sup 137} Cs{sup +} on ion exchangers from aqueous solutions containing ammonia and various chelating agents was studied. The solutions simulated radioactive waste obtained after chemical cleaning of steam generators (SG) in nuclear power plants according to the technology developed by Siemens KWU and contained ammonia and one of the following chelating agents; nitrilotriacetic acid (NTA), ethylenediamine tetraacetic acid (EDTA), and ethylenediamine(EDA), to dissolve iron and/or copper corrosion deposits. The ion exchangers used were of the composite type, and consisted of powdered cobalt(II) hexacyanoferrate incorporated into beads of a phenolsulphonic resin. Another composite adsorbent with titanium hexacyanoferrate has proved to adsorb {sup 137} Cs{sup +} from the NTA and EDA solutions more effectively than commercial caesium- selective resin Lewatit DN-KR. However, because of high concentration of competitive ammonium ions at PH 7.2(at higher PH the sorbent decomposed), the removal of radiocaesium was still insufficient. 3 figs.

Ion-exchange Resin Catalyzed Esterification of Lactic Acid with Isopropanol: a Kinetic Study

Directory of Open Access Journals (Sweden)

Amrit P. Toor

2011-05-01

Full Text Available The kinetic behavior of esterification of lactic acid with isopropanol over an acidic cation exchange resin, Amberlyst 15, was studied under isothermal condition. Isopropyl lactate synthesized in this reaction is an important pharmaceutical intermediate. The experiments were carried out in a stirred batch reactor in the temperature range of 323.15 to 353.15 K. The effect of various parameters such as temperature, molar ratio and catalyst loading was studied. Variation in parameters on rate of reaction demonstrated that the reaction was intrinsically controlled. Kinetic modeling was performed using Eley-Rideal model which acceptably fits the experimental data. The activation energy was found to be 22.007 kJ/mol and frequency factor was 0.036809 l2 g-1 mol-1 min-1 for forward reaction. The value of entropy for the forward reaction was found to be 182.317 J K-1 mol-1 . © 2011 BCREC UNDIP. All rights reserved(Received: 19th January 2011, Revised: 16th March 2011; Accepted: 16th March 2011[How to Cite: A.P. Toor, M. Sharma, S. Thakur, and R. K. Wanchoo. (2011. Ion-exchange Resin Catalyzed Esterification of Lactic Acid with Isopropanol: a Kinetic Study. Bulletin of Chemical Reaction Engineering and Catalysis, 6(1: 39-45. doi:10.9767/bcrec.6.1.791.39-45][How to Link / DOI: http://dx.doi.org/10.9767/bcrec.6.1.791.39-45 || or local:  http://ejournal.undip.ac.id/index.php/bcrec/article/view/791 ] | View in  

Properties of the Carboxylate ion exchange resins; Karboxylatjonbytarmassans egenskaper

Energy Technology Data Exchange (ETDEWEB)

Allard, Bert; Dario, Maarten [Oerebro Univ. (Sweden); Boren, Hans [Linkoepings Univ. (Sweden); Torstenfelt, Boerje [Swedpower, Stockholm (Sweden); Puigdomenech, Ignasi; Johansson, Claes [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden)

2002-09-01

Weakly acidic, carboxylic resin has been selected, together with strong base anion resins, for water purification at the Forsmark 1 and 2 reactors. For the strong (but not the weak) ion exchange resin the Nuclear Power Inspectorate has given permission to dispose the spent resins in the SFR 1 (the Final Repository for Radioactive Operational Waste). This report gives a review of the carboxylic resins and comes to the conclusion that the resins are very stable and that there should not exist any risks for increased leaching of radionuclides from SFR 1 if these resins are disposed (compared to the strong resins)

Miscibility and specific interactions in blends of poly(n-vinyl-2-pyrrolidone) and acid functional polyester resins.

NARCIS (Netherlands)

Senatore, D.; Berix, M.J.A.; Laven, J.; Benthem, van R.A.T.M.; With, de G.; Mezari, B.; Magusin, P.C.M.M.

2008-01-01

Miscibility and intermol. interactions of novel blends of poly(N-vinyl-2-pyrrolidone) (PVP) and acid functional polyester resins (APE) were studied by use of Differential Scanning Calorimetry (DSC), Attenuated Total Reflectance Fourier Transform IR (ATR-FTIR), Cross-Polarization Magic Angle Spinning

Efficient transformation of corn stover to furfural using p-hydroxybenzenesulfonic acid-formaldehyde resin solid acid.

Science.gov (United States)

Zhang, Tingwei; Li, Wenzhi; An, Shengxin; Huang, Feng; Li, Xinzhe; Liu, Jingrong; Pei, Gang; Liu, Qiying

2018-05-24

In this work, p-hydroxybenzenesulfonic acid-formaldehyde resin acid catalyst (MSPFR), was synthesized by a hydrothermal method, and employed for the furfural production from raw corn stover. Scanning electron microscopy (SEM), transmission electron microscopy (TEM), N 2 adsorption-desorption, elemental analysis (EA), thermogravimetric analysis (TGA), and Fourier transform infrared spectroscopy (FT-IR) were used to characterize the MSPFR. The effects of reaction time, temperature, solvents and corn stover loading were investigated. The MSPFR presented high catalytic activity for the formation of furfural from corn stover. When the MSPFR/corn stover mass loading ratio was 0.5, a higher furfural yield of 43.4% could be achieved at 190 °C in 100 min with 30.7% 5-hydroxymethylfurfural (HMF) yield. Additionally, quite importantly, the recyclability of the MSPFR for xylose dehydration is good, and for the conversion of corn stover was reasonable. Copyright © 2018 Elsevier Ltd. All rights reserved.

Separation of boron isotopes by ion exchange chromatography: studies on regeneration of strong base anion exchange resins

International Nuclear Information System (INIS)

Sharma, B.K.; Subramanian, R.; Mathur, P.K.

1994-01-01

The optimum conditions for the regeneration of strong base anion exchange resins of type-I and type-II were determined for cost-effective separation of isotopes of boron by ion exchange chromatography where the hydroxyl form of an anion exchange resin is equilibrated with boric acid solution containing mannitol as a complexing reagent. The possibility of using unspent alkali content of the effluent was also exploited. Removal of carbonate impurity from Rayon grade caustic lye (used as regenerant after dilution) and recycling of Ba(OH) 2 was studied to avoid waste disposal problems. (author)

New resin gel for uranium determination by diffusive gradient in thin films technique

International Nuclear Information System (INIS)

Gregusova, Michaela; Docekal, Bohumil

2011-01-01

A new resin gel based on Spheron-Oxin chelating ion-exchanger with anchored 8-hydroxyquinoline functional groups was tested for application in diffusive gradient in thin film technique (DGT) for determination of uranium. Selectivity of uranium uptake from model carbonate loaded solutions of natural water was studied under laboratory conditions and compared with selectivity of the conventional Chelex 100 based resin gel. The affinity of Spheron-Oxin functional groups enables determination of the overall uranium concentration in water containing carbonates up to the concentration level of 10 2 mg L -1 . The effect of uranium binding to the polyacrylamide (APA) and agarose diffusive gels (AGE) was also studied. Uranium is probably bound in both gels by a weak interaction with traces of acrylic acid groups in the structure of APA gel and with pyruvic and sulfonic acid groups in the AGE gel. These sorption effects can be eliminated to the negligible level by prolonged deployment of DGT probes or by disassembling probes after the 1-2 days post-sampling period that is sufficient for release of uranium from diffusive gel and its sorption in resin gel.

New resin gel for uranium determination by diffusive gradient in thin films technique

Energy Technology Data Exchange (ETDEWEB)

Gregusova, Michaela, E-mail: gregusova@iach.cz [Institute of Analytical Chemistry, Academy of Sciences of the Czech Republic v.v.i., Veveri 97, 602 00 Brno (Czech Republic); Docekal, Bohumil [Institute of Analytical Chemistry, Academy of Sciences of the Czech Republic v.v.i., Veveri 97, 602 00 Brno (Czech Republic)

2011-01-17

A new resin gel based on Spheron-Oxin chelating ion-exchanger with anchored 8-hydroxyquinoline functional groups was tested for application in diffusive gradient in thin film technique (DGT) for determination of uranium. Selectivity of uranium uptake from model carbonate loaded solutions of natural water was studied under laboratory conditions and compared with selectivity of the conventional Chelex 100 based resin gel. The affinity of Spheron-Oxin functional groups enables determination of the overall uranium concentration in water containing carbonates up to the concentration level of 10{sup 2} mg L{sup -1}. The effect of uranium binding to the polyacrylamide (APA) and agarose diffusive gels (AGE) was also studied. Uranium is probably bound in both gels by a weak interaction with traces of acrylic acid groups in the structure of APA gel and with pyruvic and sulfonic acid groups in the AGE gel. These sorption effects can be eliminated to the negligible level by prolonged deployment of DGT probes or by disassembling probes after the 1-2 days post-sampling period that is sufficient for release of uranium from diffusive gel and its sorption in resin gel.

Radiation curable epoxy resin

International Nuclear Information System (INIS)

Najvar, D.J.

1978-01-01

A carboxyl containing polymer is either prepared in the presence of a polyepoxide or reacted with a polyepoxide. The polymer has sufficient acid groups to react with only about 1 to 10 percent of the epoxide (oxirane) groups. The remaining epoxide groups are reacted with an unsaturated monocarboxylic acid such as acrylic or methacrylic acid to form a radiation curable resin

Method of removing alkyl iodides or mixtures of iodine and alkyl iodides from a gas phase and an aqueous solution phase by utilizing ion exchange resins

International Nuclear Information System (INIS)

Shimizu, Hiroshi; Mizuuchi, Noboru; Yokoyama, Fumio.

1967-01-01

Alkyl iodides and mixtures of iodine and alkyl iodides are removed from a gas phase and an aquous solution phase by using solely an anion exchange resin containing a tertiary amine or together with an anion exchange resin containing quarternary ammonium compound. The resin containing the quarternary ammonium compound is employed mainly to remove iodine, and the resin containing the tertiary amine serves mainly to remove alkyl iodides. The method can be applied to collecting a majority of the methyl iodide as well as the radioactive iodine produced in the atmosphere of a reactor in case of a fuel accident. In embodiments, it is desirable to maintain the sufficient moisture content of the anion exchange resins at a sufficient moisture level so as not to reduce the migration speed of the iodine and alkyl iodides. The iodine and alkyl iodide can be produced with high efficiency and stability independently of the relative humidity of the gas phase. In examples, a solution which consists of 20.5 mg/l of iodine and 42.2mg/l of methyl iodide flew through a column of Amberite IRA-93 alone or blended with IRA-900 at a speed of 15 /hr. respectively. The resins were able to treat 400 times their equivalent in water. (Iwakiri, K.)

Thermal behavior of halogenated imidebismaleimide resins

International Nuclear Information System (INIS)

Mohammad, A.; Al-Halim, N.Z.

1995-01-01

Several new poly-halogenated malecimides, bismaleimides and therir copoly resins were synthessised thermally from their corresponding amic acids. The synthesis was accomplished by two way method (amic acid-polimide) instead of the well-known three way method (amic acid-imide-polyimide). Thermal characterization of monomers and their cured resins was achieved using differential thermal analysis (DTA), dynamic thermogravimetric analysis (TGA) and isothermal gravimetric analysis (IGA). The effect of halogen substituent, especially in the ortho postion, is clear in the imidization proces, while polymerization proceeds almost equally in all systems. Thermal properties of homo and copolymers were correlated with their chemical structures. (author). 15 refs., 4

Studies Regarding As(V Adsorption from Underground Water by Fe-XAD8-DEHPA Impregnated Resin. Equilibrium Sorption and Fixed-Bed Column Tests

Directory of Open Access Journals (Sweden)

Mihaela Ciopec

2014-10-01

Full Text Available The characteristics of arsenic adsorption onto Fe-XAD8-DEHPA resin were studied on the laboratory scale using aqueous solutions and natural underground waters. Amberlite XAD8 resin was impregnated with di(2-ethylhexyl phosphoric acid (DEHPA via the dry method of impregnation. Fe(III ions were loaded onto the impregnated resin by exploiting the high affinity of arsenic towards iron. The studies were conducted by both in contact and continuous modes. Kinetics data revealed that the removal of arsenic by Fe-XAD8-DEHPA resin is a pseudo-second-order reaction. The equilibrium data were modelled with Freundlich Langmuir and Dubinin Radushkevich (D-R isotherms and it was found that the Freundlich model give the poorest correlation coefficient. The maximum adsorption capacity obtained from the Langmuir isotherm is 22.6 µg As(V/g of Fe-XAD8-DEHPA resin. The mean free energy of adsorption was found in this study to be 7.2 kJ/mol and the ΔG° value negative (−9.2 kJ/mol. This indicates that the sorption process is exothermal, spontaneous and physical in nature. The studied Fe-XAD8-DEHPA resin showed excellent arsenic removal performance by sorption, both from synthetic solution and the natural water sample, and could be regenerated simply by using aqueous NaOH or HCl solutions.

The determination of phosphorus in uranium minerals and resulting solutions; Determinacion de fosforo en minerales de uranio y soluciones procedentes de su beneficio

Energy Technology Data Exchange (ETDEWEB)

Petrement Eguiluz, J C; Rarellada Bellod, R; Fernandez Cellini, R

1964-07-01

Interferences of several elements present in Spanish uranium minerals in the phosphorus determination by the spectrophotometrical method of the molibdovanada te phosphoric acid are studied. A method is described with a previous separation of these element by a cationic resin. This method is successfully applied to the phosphorus determination in acid or alkaline lixiviation solutions of uranium minerals, as well as in the evaluates of ion exchange resins used used technically for the concentration of solutions with a low uranium content. (Author) 11 refs.

A basic study for the boron thermal regeneration system using anion exchange resins

International Nuclear Information System (INIS)

Frantiesek, P.; Kotaka, Masahiro; Okamoto, Makoto; Kakihana, Hidetake.

1979-01-01

For the boron thermal regeneration system (BTRS), the basic characteristics of commercial anion exchange resin have been investigated on the swelling characteristics, absorption, desorption and temperature coefficient of exchange capacity for boric acid. The equilibrium capacity increases as decrease of temperature and depends strongly on the degrees of cross linking having a maximum point at about 7% of DVB. The temperature coefficient of equilibrium capacity of boric acid is also a function of the concentration of external solution and of the cross linking having a maximum point around 7% of DVB. (author)

Effects of the peracetic acid and sodium hypochlorite on the colour stability and surface roughness of the denture base acrylic resins polymerised by microwave and water bath methods.

Science.gov (United States)

Fernandes, Flavio H C N; Orsi, Iara A; Villabona, Camilo A

2013-03-01

This study evaluated the surface roughness (Ra) and color stability of acrylic resin colors (Lucitone 550, QC-20 and Vipi-Wave) used for fabricating bases for complete, removable dentures, overdentures and prosthetic protocol after immersion in chemical disinfectants (1% sodium hypochlorite and 2% peracetic acid) for 30 and 60 minutes. Sixty specimens were made of each commercial brand of resin composite, and divided into 2 groups according to the chemical disinfectants. Specimens had undergone the finishing and polishing procedures, the initial color and roughness measurements were taken (t=0), and after this, ten test specimens of each commercial brand of resin composite were immersed in sodium hypochlorite and ten in peracetic acid, for 30 and 60 minutes, with measurements being taken after each immersion period. These data were submitted to statistical analysis. There was evidence of an increase in Ra after 30 minutes immersion in the disinfectants in all the resins, with QC-20 presenting the highest Ra values, and Vipi-Wave the lowest. After 60 minutes immersion in the disinfectants all the resins presented statistically significant color alteration. Disinfection with 1% sodium hypochlorite and peracetic acid altered the properties of roughness and color of the resins. © 2012 The Gerodontology Society and John Wiley & Sons A/S.

Chromatography of metal ions with a triazine chelating resin

International Nuclear Information System (INIS)

Wang, W.N.

1979-05-01

The synthesis, characterization, and some analytical applications of a new triazine resin are described. Separation of group IB, IIB, VIB, and VIIB metal ions from group VIII metal ions is achieved by this PDT-4 resin. Calcium(II) and magnesium(II) are taken up at pH = 6, 0.1 M acetate and are eluted at pH = 6, 0.1 M sodium nitrate. Copper(II) is retained at pH = 6, 0.1 M acetate and pH = 1 hydrochloric acid and is eluted subsequently by 5 M perchloric acid. Molybdenum(VI) is sorbed selectively from 0.1 N sulfuric acid or hydrochloric acid and is eluted in a tight band by 0.1 N sodium hydroxide. Numerous rapid column chromatographic separations are reported using this new resin, including analysis of NBS standard samples

Pengaruh Minuman Kopi terhadap Perubahan Warna pada Resin Komposit

OpenAIRE

Aprilia Aprilia; Linda Rochyani; Erry Rahardianto

2015-01-01

Objective: The aim of this research was to investigate the influence of coffee beverage on hybrid composite resin discoloration. Material and method: This study used hybrid composite resin with A3 color, and was done by soaking composite resin plates in coffee solution for 1, 3, 5, and 7 days, corresponding to equivalent coffee usage for 6 months, 1, 1.5, and 2 years. The same measurements of reflectance were done before and after soaking into coffee solution. In the measurement, a beam from ...

HTGR fuel development: investigations of breakages of uranium-loaded weak acid resin microspheres

International Nuclear Information System (INIS)

Carpenter, J.A. Jr.

1977-11-01

During the HTGR fuel development program, a high percentage of uranium-loaded weak acid resin microspheres broke during pneumatic transfer, carbonization, and conversion. One batch had been loaded by the UO 3 method; the other by the ammonia neutralization method. To determine the causes of failure, samples of the two failed batches were investigated by optical microscopy, scanning electron microscopy, electron beam microprobe, and other techniques. Causes of failure are postulated and methods are suggested to prevent recurrence of this kind of failure

One pot synthesis of chitosan grafted quaternized resin for the removal of nitrate and phosphate from aqueous solution.

Science.gov (United States)

Banu, H Thagira; Meenakshi, Sankaran

2017-11-01

The present study deals with the synthesis of chitosan quaternized resin for efficient removal of nitrate and phosphate from aqueous solution. The resin was characterized with FTIR, SEM with EDX and XRD. Batch method was carried out to optimize various parameters such as contact time, initial concentration of nitrate and phosphate, dosage, pH, co-anions and temperature on the adsorption capacity of the adsorbent. The adsorption process illustrated that the Freundlich isotherm and the pseudo-second order are the best fitted models for the sorption of both anions. The respective negative values of ΔH° and ΔG° revealed that the adsorption of both the anions were exothermic and spontaneous. The removal efficiency of nitrate and phosphate on chitosan quaternized resin were 78% and 90% respectively with 0.1g of adsorbent and the initial concentration as 100mg/L. Nitrate and phosphate anions adsorbed effectively on chitosan quaternized resin by replacing Cl - ions from quaternary site through electrostatic attraction as well as ion-exchange mechanism. Hydrogen bonding also played important role in adsorption process. Even after 7th regeneration cycle the adsorbent retained its adsorption capacity as 23.7mg/g and 30.4mg/g for both nitrate and phosphate respectively. Copyright © 2017 Elsevier B.V. All rights reserved.

Sulfur geochemistry of hydrothermal waters in Yellowstone National Park, Wyoming, USA. III. An anion-exchange resin technique for sampling and preservation of sulfoxyanions in natural waters

Directory of Open Access Journals (Sweden)

Ball James W

2003-06-01

Full Text Available A sampling protocol for the retention, extraction, and analysis of sulfoxyanions in hydrothermal waters has been developed in the laboratory and tested at Yellowstone National Park and Green Lake, NY. Initial laboratory testing of the anion-exchange resin Bio-Rad™ AG1-X8 indicated that the resin was well suited for the sampling, preservation, and extraction of sulfate and thiosulfate. Synthetic solutions containing sulfate and thiosulfate were passed through AG1-X8 resin columns and eluted with 1 and 3 M KCl, respectively. Recovery ranged from 89 to 100%. Comparison of results for water samples collected from five pools in Yellowstone National Park between on-site IC analysis (U.S. Geological Survey mobile lab and IC analysis of resin-stored sample at SUNY-Stony Brook indicates 96 to 100% agreement for three pools (Cinder, Cistern, and an unnamed pool near Cistern and 76 and 63% agreement for two pools (Sulfur Dust and Frying Pan. Attempts to extract polythionates from the AG1-X8 resin were made using HCl solutions, but were unsuccessful. Bio-Rad™ AG2-X8, an anion-exchange resin with weaker binding sites than the AG1-X8 resin, is better suited for polythionate extraction. Sulfate and thiosulfate extraction with this resin has been accomplished with KCl solutions of 0.1 and 0.5 M, respectively. Trithionate and tetrathionate can be extracted with 4 M KCl. Higher polythionates can be extracted with 9 M hydrochloric acid. Polythionate concentrations can then be determined directly using ion chromatographic methods, and laboratory results indicate recovery of up to 90% for synthetic polythionate solutions using AG2-X8 resin columns.

Resin Flow in Fiber Preformed by Vacuum Assisted Resin Transfer Molding with Flexible Tools

Directory of Open Access Journals (Sweden)

M.M. Shokrieh

2008-12-01

Full Text Available Vacuum assisted resin transfer molding, as a sub-branch of RTM is a method of manufacturing composite specimens. Considering the industrial development of this method, different modified techniques are designed to improve its performance. Among these techniques, using a half flexible mold is regarded as an important method. In this work, dominant equations of resin flow through the mold in polar coordinates are solved analytically. Based on this approach, closed-form solutions have been presented for different parameters such as thickness variation of preformed fiber, resin pressure, resin velocity and fiber volume fraction as functions of two variables, namely, time and the distance from injection port. After verification of the approach employed in this work, the results are presented. Important parameters influencing the quality and the rate production are studied in detail.

Resin bleed improvement on surface mount semiconductor device

Science.gov (United States)

Rajoo, Indra Kumar; Tahir, Suraya Mohd; Aziz, Faieza Abdul; Shamsul Anuar, Mohd

2018-04-01

Resin bleed is a transparent layer of epoxy compound which occurs during molding process but is difficult to be detected after the molding process. Resin bleed on the lead on the unit from the focused package, SOD123, can cause solderability failure at end customer. This failed unit from the customer will be considered as a customer complaint. Generally, the semiconductor company has to perform visual inspection after the plating process to detect resin bleed. Mold chase with excess hole, split cavity & stepped design ejector pin hole have been found to be the major root cause of resin bleed in this company. The modifications of the mold chase, changing of split cavity to solid cavity and re-design of the ejector pin proposed were derived after a detailed study & analysis conducted to arrive at these solutions. The solutions proposed have yield good results during the pilot run with zero (0) occurrence of resin bleed for 3 consecutive months.

Chemical derivatization to enhance chemical/oxidative stability of resorcinol-formaldehyde resin

Energy Technology Data Exchange (ETDEWEB)

Hubler, T.L. [Pacific Northwest National Lab., Richland, WA (United States)

1997-10-01

The goal of this task is to develop modified resorcinol-formaldehyde (R-F) resin to improve the chemical/oxidative stability of the resin. R-F resin is a regenerable organic ion-exchange resin that is selective for cesium ion in highly alkaline, high ionic-strength solutions. R-F resin tends to undergo chemical degradation, reducing its ability to remove cesium ion from waste solutions; the mechanistic details of these decomposition reactions are currently unknown. The approach used for this task is chemical modification of the resin structure, particularly the resorcinol ring unit of the polymer resin. This approach is based on prior characterization studies conducted at Pacific Northwest National Laboratory (PNNL) that indicated the facile chemical degradation of the resin is oxidation of the resorcinol ring to the para-quinone structure, with subsequent loss of ion-exchange sites for cesium ion. R-F resin represents an important alternative to current radiocesium remediation technology for tank wastes at both the Hanford and Savannah River sites, particularly if regenerable resins are needed.

Uranium loss from BISO-coated weak-acid-resin HTGR fuel

International Nuclear Information System (INIS)

Pearson, R.L.; Lindemer, T.B.

1977-02-01

Recycle fuel for the High-Temperature Gas-Cooled Reactor (HTGR) contains a weak-acid-resin (WAR) kernel, which consists of a mixture of UC 2 , UO 2 , and free carbon. At 1900 0 C, BISO-coated WAR UC 2 or UC 2 -UO 2 kernels lose a significant portion of their uranium in several hundred hours. The UC 2 decomposes and uranium diffuses through the pyrolytic coating. The rate of escape of the uranium is dependent on the temperature and the surface area of the UC 2 , but not on a temperature gradient. The apparent activation energy for uranium loss, ΔH, is approximately 90 kcal/mole. Calculations indicate that uranium loss from the kernel would be insignificant under conditions to be expected in an HTGR

Evaluation of some anionic exchange resins as potential tablet ...

African Journals Online (AJOL)

The effect of resin concentration and compression force on the properties of tablets using the selected resin was investigated. In addition, the disintegrant efficacy of the selected resin in the tablet formulations containing either a basic drug, e.g., dextromethorphan hydrobromide (DMP), or an acidic drug, e.g., diclofenac ...

SYNTHESIS OF METHYL TERT-BUTYL ETHER CATALYZED BY ACIDIC ION-EXCHANGE RESINS - INFLUENCE OF THE PROTON ACTIVITY

NARCIS (Netherlands)

PANNEMAN, HJ; BEENACKERS, AACM

1995-01-01

The catalytic activity of various strong acid ion-exchange resins on the synthesis of methyl tert-butyl ether (MtBE) from methanol and isobutene has been investigated. Relative to Amberlyst 15, Kastel CS 381 and Amberlyst CSP have similar rate constants, whereas Duolite ES 276 and Amberlyst XE 307

Two solid-phase recycling method for basic ionic liquid [C4mim]Ac by macroporous resin and ion exchange resin from Schisandra chinensis fruits extract.

Science.gov (United States)

Ma, Chun-hui; Zu, Yuan-gang; Yang, Lei; Li, Jian

2015-01-22

In this study, two solid-phase recycling method for basic ionic liquid (IL) 1-butyl-3-methylimidazolium acetate ([C4mim]Ac) were studied through a digestion extraction system of extracting biphenyl cyclooctene lignans from Schisandra chinensis. The RP-HPLC detection method for [C4mim]Ac was established in order to investigate the recovery efficiency of IL. The recycling method of [C4mim]Ac is divided into two steps, the first step was the separation of lignans from the IL solution containing HPD 5000 macroporous resin, the recovery efficiency and purity of [C4mim]Ac achieved were 97.8% and 67.7%, respectively. This method cannot only separate the lignans from [C4mim]Ac solution, also improve the purity of lignans, the absorption rate of lignans in [C4mim]Ac solution was found to be higher (69.2%) than that in ethanol solution (57.7%). The second step was the purification of [C4mim]Ac by the SK1B strong acid ion exchange resin, an [C4mim]Ac recovery efficiency of 55.9% and the purity higher than 90% were achieved. Additionally, [C4mim]Ac as solvent extraction of lignans from S. chinensis was optimized, the hydrolysis temperature was 90°C and the hydrolysis time was 2h. Copyright © 2014 Elsevier B.V. All rights reserved.

Commercial Ion Exchange Resin Vitrification in Borosilicate Glass

International Nuclear Information System (INIS)

Cicero-Herman, C.A.; Workman, P.; Poole, K.; Erich, D.; Harden, J.

1998-05-01

Bench-scale studies were performed to determine the feasibility of vitrification treatment of six resins representative of those used in the commercial nuclear industry. Each resin was successfully immobilized using the same proprietary borosilicate glass formulation. Waste loadings varied from 38 to 70 g of resin/100 g of glass produced depending on the particular resin, with volume reductions of 28 percent to 68 percent. The bench-scale results were used to perform a melter demonstration with one of the resins at the Clemson Environmental Technologies Laboratory (CETL). The resin used was a weakly acidic meth acrylic cation exchange resin. The vitrification process utilized represented a approximately 64 percent volume reduction. Glass characterization, radionuclide retention, offgas analyses, and system compatibility results will be discussed in this paper

The effect of submersion denture base acrylic resin in a betel leaf ekstract solution against growth Candida albicans

Directory of Open Access Journals (Sweden)

Andi Izham

2016-06-01

Full Text Available Denture base is a protesa which replace some or all of the lost original teeth and surrounding tissues. The Pupose of making protesa is for restore the function, appearance, comfort and impaired health result lost teeth. One part of the denture base is base plate. Microorganisms are often found in the oral cavity is Candida albicans (C.albicans approximately 40% in the oral cavity.C.albicans can penetrate the acrylic resin that can infect the soft tissue and is the cause of denture stomatitis therefore the disinfection of denture base is a important factor that must be done. In general betel leaves contant up to 4.2% essential oil compounds and phenyl propanoid and tannin. These compounds is a antimicroba and antifungal which can inhibit the growth of several type of bacteria among others Escherichia coli, Salmonella sp, Staphylococcus aurens, Klebstella, Pasteurella and can turn off the C.albicans. The purpose of the research is to determine how the effect of submersion denture base acrylic resin in a betel leaf ekstract solution against growth C.albicans.Type of research is an experimental laboratory with a longitudinal design (follow-up study. The sampling method used is total sampling. The results showed that the number of C.albicans colonies n denture base acrylic resin which soaked betel leaf extract solution that the dilution 10-1  with consentration 2.5% total colony count is 2 and the results 2.0 x 101 CFU/ml, on a control solution that the dilution 10-2 total colony 355 and the result 3.55 x 104 CFU/ml, that the dilution  10-3 total colony 62 and the result 6.2 x 104 CFU/ml.

Direct injection analysis of fatty and resin acids in papermaking process waters by HPLC/MS.

Science.gov (United States)

Valto, Piia; Knuutinen, Juha; Alén, Raimo

2011-04-01

A novel HPLC-atmospheric pressure chemical ionization/MS (HPLC-APCI/MS) method was developed for the rapid analysis of selected fatty and resin acids typically present in papermaking process waters. A mixture of palmitic, stearic, oleic, linolenic, and dehydroabietic acids was separated by a commercial HPLC column (a modified stationary C(18) phase) using gradient elution with methanol/0.15% formic acid (pH 2.5) as a mobile phase. The internal standard (myristic acid) method was used to calculate the correlation coefficients and in the quantitation of the results. In the thorough quality parameters measurement, a mixture of these model acids in aqueous media as well as in six different paper machine process waters was quantitatively determined. The measured quality parameters, such as selectivity, linearity, precision, and accuracy, clearly indicated that, compared with traditional gas chromatographic techniques, the simple method developed provided a faster chromatographic analysis with almost real-time monitoring of these acids. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Corrosion of alloy C-22 in organic acid solutions

International Nuclear Information System (INIS)

Carranza, Ricardo M.; Rodriguez, Martin A.; Giordano, Celia M.

2007-01-01

Electrochemical studies such as cyclic potentiodynamic polarization (CPP) and electrochemical impedance spectroscopy (EIS) were performed to determine the corrosion behavior of Alloy 22 (N06022) in 1M NaCl solutions at various pH values from acidic to neutral at 90 C degrees. All the tested material was wrought Mill Annealed (MA). Tests were also performed in NaCl solutions containing weak organic acids such as oxalic, acetic, citric and picric acids. Results show that the corrosion rate of Alloy 22 was significantly higher in solutions containing oxalic acid than in solutions of pure NaCl at the same pH. Citric and Picric acids showed a slightly higher corrosion rate, and Acetic acid maintained the corrosion rate of pure chloride solutions at the same pH. Organic acids revealed to be weak inhibitors for crevice corrosion. Higher concentration ratios, compared to nitrate ions, were needed to completely inhibit crevice corrosion in chloride solutions. Results are discussed considering acid dissociation constants, buffer capacity and complex formation constants of the different weak acids. (author) [es

Color stability of sealed composite resin restorative materials after ultraviolet artificial aging and immersion in staining solutions.

Science.gov (United States)

Catelan, Anderson; Briso, André Luiz Fraga; Sundfeld, Renato Hermann; Goiato, Marcelo Coelho; dos Santos, Paulo Henrique

2011-04-01

The color alteration of resin-based materials is one of the most common reasons to replace esthetic dental restorations. This study assessed the influence of surface sealant (Biscover) on the color stability of nanofilled (Supreme XT) and microhybrid (Vit-l-escence and Opallis) composite resins after artificial aging. One hundred disc-shaped (6 × 1.5 mm) specimens were made for each composite resin. After 24 hours, all specimens were polished and sealant was applied to 50 specimens of each material. Baseline color was measured according to the CIE L*a*b* system using a reflection spectrophotometer. Ten specimens of each group were aged for 252 h in an ultraviolet (UV)-accelerated aging chamber or immersed for 4 weeks in cola soft drink, orange juice, red wine staining solutions or distilled water as control. Color difference (ΔE) after aging was calculated based on the color coordinates before (baseline) and after aging/staining treatment. Data were analyzed with 2-way ANOVA and Fisher's test (α=.05). The results showed significant changes in color after artificial aging in all the groups (Paging, and the cola soft drink. The lowest values of ΔE were found for specimens stored in distilled water. All composite resins showed some color alteration after the aging methods. The surface sealant did not alter the color stability of the tested materials. Copyright © 2011 The Editorial Council of the Journal of Prosthetic Dentistry. Published by Mosby, Inc. All rights reserved.

Kinetic investigation of the immobilization of chromotropic acid derivatives onto anion exchange resin

Directory of Open Access Journals (Sweden)

Savić Jasmina

2007-01-01

Full Text Available The adsorption kinetics of pyrazol- (РАСА and imidazol-azo-chromo-tropic acid (IACA onto Dowex 1-X8 resin, as a function of the dye concentration and temperature were investigated at pH 4.5. The pseudo-first- and second-order kinetic models and intraparticle diffusion model were used to describe the obtained kinetic data. The adsorption rate constants were found to be in the order of magnitude 10-2 min-1 for all of the used kinetics models. The adsorption capacity increases with increasing initial dye concentration. The study of adsorption kinetics at different temperatures (in the range from 5 to 25 °C reveals an increase in the rate of adsorption and adsorption capacity with increasing temperature. The activation energy (in the case of РАСА 16.6 kJ/mol, and for IACA 11.3 kJ/mol was determined using the Arrhenius dependence. Electrostatic interactions between the dye and resin beads were shown to be the adsorption mechanism.

Development of radiation-curable resin based on natural rubber

Energy Technology Data Exchange (ETDEWEB)

Mohd, Dahlan; Harun, Abdul Ghani [Nuclear Energy Unit, Bangi, Selangor (Malaysia)

1994-12-31

A new radiation curable resin based on natural rubber has been developed. The resin was based on the reaction between low molecular weight epoxidised natural rubber and acrylic acid. When formulated with reactive monomers and photoinitiator, it solidified upon irradiation with UV light. The resin may find applications in coating for cellulosic-based substrates and pressure-sensitive adhesive.

Development of radiation-curable resin based on natural rubber

International Nuclear Information System (INIS)

Dahlan Mohd; Abdul Ghani Harun

1993-01-01

A new radiation curable resin based on natural rubber has been developed. The resin was based on the reaction between low molecular weight epoxidised natural rubber and acrylic acid. When formulated with reactive monomers and photoinitiator, it solidified upon irradiation with UV light. The resin may find applications in coating for cellulosic-based substrates and pressure-sensitive adhesive

Development, design, and preliminary operation of a resin-feed processing facility for resin-based HTGR fuels

International Nuclear Information System (INIS)

Haas, P.A.; Drago, J.P.; Million, D.L.; Spence, R.D.

1978-01-01

Fuel kernels for recycle of 233 U to High-Temperature Gas-Cooled Reactors are prepared by loading carboxylic acid cation exchange resins with uranium and carbonizing at controlled conditions. Resin-feed processing was developed and a facility was designed, installed, and operated to control the kernel size, shape, and composition by processing the resin before adding uranium. The starting materials are commercial cation exchange resins in the sodium form. The size separations are made by vibratory screening of resin slurries in water. After drying in a fluidized bed, the nonspherical particles are separated from spherical particles on vibratory plates of special design. The sized, shape-separated spheres are then rewetted and converted to the hydrogen form. The processing capacity of the equipment tested is equivalent to about 1 kg of uranium per hour and could meet commercial recycle plant requirements without scale-up of the principal process components

EPICOR-II resin degradation results from first resin samples of PF-8 and PF-20

International Nuclear Information System (INIS)

McConnell, J.W. Jr.; Sanders, R.D. Sr.

1985-12-01

The 28 March 1979 accident at Three Mile Island Unit 2 released approximately 560,000 gallons of contaminated water to the Auxiliary and Fuel Handling Buildings. The water was decontaminated using a demineralization system called EPICOR-II developed by Epicor, Inc. The Low-Level Waste Data Base Development - EPICOR-II Resin/Liner Investigation Project is studying the chemical and physical conditions of the synthetic ion exchange resins found in several EPICOR-II prefilters. This report summarizes results and analyses of the first sampling of ion exchange resins from EPICOR-II prefilters PE-8 and -20. Results are compared with baseline data from tests performed on unirradiated Epicor, Inc. resins to determine if degradation has occurred due to the high internal radiation dose received by the EPICOR-II resins. Results also are compared with recent findings on resin degradation by Battelle Columbus Laboratories and Brookhaven National Laboratory. Analyses comparing test results of resins from EPICOR-II prefilters PF-8 and -20 with unirradiated resins obtained from Epicor, Inc. show resin degradation has occurred in some of the EPICOR-II resins examined. The mechanism of degradation is compared with work of other researchers and is consistent with their findings. The strong acid cation resins (divinylbenzene, styrene base structure) are losing effective cross-linking along with scission of functional groups and are experiencing first an increase and eventually a decrease in total exchange capacity as the absorbed radiation dose increases. The phenolic cation resins (phenol-formaldehyde base structure) show a loss of effective cross-linking and oxidation of the polymer chain. Analyses of resins removed from EPICOR-II prefilters PF-8 and -20 over the next several years should show a further increase in degradation

Adsorptive removal of Cu(II) from aqueous solutions using collagen-tannin resin

Energy Technology Data Exchange (ETDEWEB)

Sun Xia; Huang Xin [Department of Biomass Chemistry and Engineering, Sichuan University, Chengdu 610065 (China); Liao Xuepin, E-mail: xpliao@scu.edu.cn [Department of Biomass Chemistry and Engineering, Sichuan University, Chengdu 610065 (China); National Engineering Laboratory for Clean Technology of Leather Manufacture, Sichuan University, Chengdu 610065 (China); Shi Bi, E-mail: shibi@scu.edu.cn [National Engineering Laboratory for Clean Technology of Leather Manufacture, Sichuan University, Chengdu 610065 (China)

2011-02-28

The collagen-tannin resin (CTR), as a novel adsorbent, was prepared via a reaction of collagen with black wattle tannin and aldehyde, and its adsorption properties to Cu(II) were systematically investigated, including pH effect, adsorption equilibrium, adsorption kinetics, and column adsorption. The adsorption capacity of Cu(II) on CTR was pH-dependent, and it increased with the increase of solution pH. The adsorption isotherms were well described by Langmuir isotherm model with correlating constant (R{sup 2}) higher than 0.99. The adsorption capacity determined at 303 K was high up to 0.26 mmol/g, which was close to the value (0.266 mmol/g) estimated from Langmuir equation. The adsorption capacity was increased with the increase of temperature, and thermodynamic calculations suggested that the adsorption of Cu(II) on CTR is an endothermic process. The adsorption kinetics were well fitted by the pseudo-second-order rate model. Further column studies suggested that CTR was effective for the removal of Cu(II) from solutions, and more than 99% of Cu(II) was desorbed from column using 0.1 mol/L HNO{sub 3} solution. The CTR column can be reused to adsorb Cu(II) without any loss of adsorption capacity.

Sulfur geochemistry of hydrothermal waters in Yellowstone National Park, Wyoming, USA. III. An anion-exchange resin technique for sampling and preservation of sulfoxyanions in natural waters

Science.gov (United States)

Druschel, G.K.; Schoonen, M.A.A.; Nordstorm, D.K.; Ball, J.W.; Xu, Y.; Cohn, C.A.

2003-01-01

A sampling protocol for the retention, extraction, and analysis of sulfoxyanions in hydrothermal waters has been developed in the laboratory and tested at Yellowstone National Park and Green Lake, NY. Initial laboratory testing of the anion-exchange resin Bio-Rad??? AG1-X8 indicated that the resin was well suited for the sampling, preservation, and extraction of sulfate and thiosulfate. Synthetic solutions containing sulfate and thiosulfate were passed through AG1-X8 resin columns and eluted with 1 and 3 M KCl, respectively. Recovery ranged from 89 to 100%. Comparison of results for water samples collected from five pools in Yellowstone National Park between on-site IC analysis (U.S. Geological Survey mobile lab) and IC analysis of resin-stored sample at SUNY-Stony Brook indicates 96 to 100% agreement for three pools (Cinder, Cistern, and an unnamed pool near Cistern) and 76 and 63% agreement for two pools (Sulfur Dust and Frying Pan). Attempts to extract polythionates from the AG1-X8 resin were made using HCl solutions, but were unsuccessful. Bio-Rad??? AG2-X8, an anion-exchange resin with weaker binding sites than the AG1-X8 resin, is better suited for polythionate extraction. Sulfate and thiosulfate extraction with this resin has been accomplished with KCl solutions of 0.1 and 0.5 M, respectively. Trithionate and tetrathionate can be extracted with 4 M KCl. Higher polythionates can be extracted with 9 M hydrochloric acid. Polythionate concentrations can then be determined directly using ion chromatographic methods, and laboratory results indicate recovery of up to 90% for synthetic polythionate solutions using AG2-X8 resin columns. ?? The Royal Society of Chemistry and the Division of Geochemistry of the American Chemical Society 2003.

Extraction of high quality DNA from seized Moroccan cannabis resin (Hashish.

Directory of Open Access Journals (Sweden)

Moulay Abdelaziz El Alaoui

Full Text Available The extraction and purification of nucleic acids is the first step in most molecular biology analysis techniques. The objective of this work is to obtain highly purified nucleic acids derived from Cannabis sativa resin seizure in order to conduct a DNA typing method for the individualization of cannabis resin samples. To obtain highly purified nucleic acids from cannabis resin (Hashish free from contaminants that cause inhibition of PCR reaction, we have tested two protocols: the CTAB protocol of Wagner and a CTAB protocol described by Somma (2004 adapted for difficult matrix. We obtained high quality genomic DNA from 8 cannabis resin seizures using the adapted protocol. DNA extracted by the Wagner CTAB protocol failed to give polymerase chain reaction (PCR amplification of tetrahydrocannabinolic acid (THCA synthase coding gene. However, the extracted DNA by the second protocol permits amplification of THCA synthase coding gene using different sets of primers as assessed by PCR. We describe here for the first time the possibility of DNA extraction from (Hashish resin derived from Cannabis sativa. This allows the use of DNA molecular tests under special forensic circumstances.

Method of pyrolysis for spent ion-exchange resins

International Nuclear Information System (INIS)

Aoyama, Yoshiyuki; Matsuda, Masami; Kawamura, Fumio; Yusa, Hideo.

1985-01-01

Purpose: To prevent the generation of noxious sulfur oxide and ammonia on the pyrolysis for spent ion-exchange resins discharged from nuclear power plants. Method: In the case where the pyrolysis is made for the cationic exchange resins having sulfonic acids as the ion-exchange group, alkali metals or alkaline earth metals capable of reacting with sulfonic acid groups to form solid sulfates are previously deposited by way of ion-exchange reactions prior to the pyrolysis. In another case of the anionic exchange resins having quarternary ammonium groups as the ion-exchange groups, halogenic elements capable of reacting with the ammonium groups to form solid ammonium salts are deposited to the ion-exchange resins through ion-exchange reactions prior to the pyrolysis. As a result, the amount of the binders used can be reduced, and this method can be used in a relatively simple processing facility. (Horiuchi, T.)

NIR spectroscopic properties of aqueous acids solutions.

Science.gov (United States)

Omar, Ahmad Fairuz; Atan, Hanafi; Matjafri, Mohd Zubir

2012-06-15

Acid content is one of the important quality attributes in determining the maturity index of agricultural product, particularly fruits. Despite the fact that much research on the measurement of acidity in fruits through non-destructive spectroscopy analysis at NIR wavelengths between 700 to 1,000 nm has been conducted, the same response towards individual acids is not well known. This paper presents NIR spectroscopy analysis on aqueous citric, tartaric, malic and oxalic solutions through quantitative analysis by selecting a set of wavelengths that can best be used to measure the pH of the solutions. The aquaphotomics study of the acid solutions has generated R² above 0.9 for the measurement of all acids. The most important wavelengths for pH are located at 918-925 nm and 990-996 nm, while at 975 nm for water.

Safeguards Analytical Laboratory evaluation program. Part 1. Resin bead mass spectrometry. Part 2. Results of a resin bead field experiment-Tastex-J

International Nuclear Information System (INIS)

Walker, R.L.; Smith, D.H.; Carter, J.A.; Musick, W.R.; Donohue, D.L.; Deron, S.; Asakura, Y.; Kagami, K.; Irinouchi, S.; Masui, J.

1981-01-01

The first part of this report covers background of resin bead spectrometry and the new batch resin bead method. In the original technique, about ten anion resin beads in the nitrate form were exposed to the diluted sample solution. The solution was adjusted to be a 8 M HNO 3 and to have about 1 μg U per bead. Up to 48 hours of static contact between beads and solution was required for adsorption of 1 to 3 ng Pu and U per bead to be achieved. Under these conditions, contamination was a problem at reprocessing facilities. The new batch techniques reduces the risk of contamination by handling one hundred times more U in the final diluted sample which is exposed to a proportionately larger number of beads. Moreover, it only requires ten minutes adsorption time to provide about 1000 purified samples for mass spectrometry. The amounts of Pu and U adsorbed versus time were determined and results are tabulated. The second part of this report briefly summarizes results of resin bead field tests completed at the Power Reactor and Nuclear Fuel Development Corporation (PNC) reprocessing plant in Tokai-mura, Japan. Both methods, the original small-sample resin bead and the batch technique, were investigated on spent fuel solutions. Beads were prepared at PNC and distributed to IAEA and ORNL along with dried residues for conventional mass spectrometric analysis at IAEA. Parallel measurements were made at PNC using their normal measuring routines. The U and Pu measurements of all resin and those of PNC are in excellent agreement for the batch method. Discrepancies were noted in the U measurements by the original method

Americium Separations from High-Salt Solutions Using Anion Exchange

International Nuclear Information System (INIS)

Barr, Mary E.; Jarvinen, Gordon D.; Stark, Peter C.; Chamberlin, Rebecca M.; Bartsch, Richard A.; Zhang, Z.Y.; Zhao, W.

2001-01-01

The aging of the US nuclear stockpile presents a number of challenges, including the increasing radioactivity of plutonium residues due to the ingrowth of 241 Am from the β-decay of 241 Pu. We investigated parameters that affect the sorption of Am onto anion-exchange resins from concentrated effluents derived from nitric acid processing of plutonium residues. These postevaporator wastes are nearly saturated solutions of acidic nitrate salts, and americium removal is complicated by physical factors, such as solution viscosity and particulates, as well as by the presence of large quantities of competing metals and acid. Single- and double-contact batch distribution coefficients for americium and neodymium from simple and complex surrogate solutions are presented. Varied parameters include the nitrate salt concentration and composition and the nitric acid concentration. We find that under these extremely concentrated conditions, Am(III) removal efficiencies can surpass 50% per contact. Distribution coefficients for both neodymium and americium are insensitive to solution acidity and appear to be driven primarily by low water activities of the solutions

Syringaresinol: A Renewable and Safer Alternative to Bisphenol A for Epoxy-Amine Resins.

Science.gov (United States)

Janvier, Marine; Hollande, Louis; Jaufurally, Abdus Samad; Pernes, Miguel; Ménard, Raphaël; Grimaldi, Marina; Beaugrand, Johnny; Balaguer, Patrick; Ducrot, Paul-Henri; Allais, Florent

2017-02-22

A renewable bisepoxide, SYR-EPO, was prepared from syringaresinol, a naturally occurring bisphenol deriving from sinapic acid, by using a chemo-enzymatic synthetic pathway. Estrogenic activity tests revealed no endocrine disruption for syringaresinol. Its glycidylation afforded SYR-EPO with excellent yield and purity. This biobased, safe epoxy precursor was then cured with conventional and renewable diamines for the preparation of epoxy-amine resins. The resulting thermosets were thermally and mechanically characterized. Thermal analyses of these new resins showed excellent thermal stabilities (T d5 % =279-309 °C) and T g ranging from 73 to 126 °C, almost reaching the properties of those obtained with the diglycidylether of bisphenol A (DGEBA), extensively used in the polymer industry (T d5 % =319 °C and T g =150 °C for DGEBA/isophorone diamine resins). Degradation studies in NaOH and HCl aqueous solutions also highlighted the robustness of the syringaresinol-based resins, similar to bisphenol A (BPA). All these results undoubtedly confirmed the potential of syringaresinol as a greener and safer substitute for BPA. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

SOLVENT EFFECTS IN THE LIQUID-PHASE HYDRATION OF CYCLOHEXENE CATALYZED BY A MACROPOROUS STRONG ACID ION-EXCHANGE RESIN

NARCIS (Netherlands)

PANNEMAN, HJ; BEENACKERS, AACM

1992-01-01

The liquid-phase hydration of cyclohexene, a pseudo first order reversible reaction catalyzed by a strong acid ion exchange resin, macroporous Amberlite XE 307, was investigated in solvent mixtures of water and sulfolane. A decrease by a factor of 3 and 6 is observed in the experimentally measured

Containment of Nitric Acid Solutions of Plutonium-238

International Nuclear Information System (INIS)

Reimus, M.A.H.; Silver, G.L.; Pansoy-Hjelvik, L.; Ramsey, K.

1999-01-01

The corrosion of various metals that could be used to contain nitric acid solutions of Pu-238 has been studied. Tantalum and tantalum/2.5% tungsten resisted the test solvent better than 304L stainless steel and several INCONEL alloys. The solvent used to imitate nitric acid solutions of Pu-238 contained 70% nitric acid, hydrofluoric acid, and ammonium hexanitratocerate

Mechanical properties of dental resin composites by co-filling diatomite and nanosized silica particles

International Nuclear Information System (INIS)

Wang Hua; Zhu Meifang; Li Yaogang; Zhang Qinghong; Wang Hongzhi

2011-01-01

The aim of this study was to investigate the mechanical property effects of co-filling dental resin composites with porous diatomite and nanosized silica particles (OX-50). The purification of raw diatomite by acid-leaching was conducted in a hot 5 M HCl solution at 80 deg. C for 12 h. Both diatomite and nanosized SiO 2 were silanized with 3-methacryloxypropyltrimethoxysilane. The silanized inorganic particles were mixed into a dimethacrylate resin. Purified diatomite was characterized by X-ray diffraction, UV-vis diffuse reflectance spectroscopy and an N 2 adsorption-desorption isotherm. Silanized inorganic particles were characterized using Fourier transform infrared spectroscopy and a thermogravimetric analysis. The mechanical properties of the composites were tested by three-point bending, compression and Vicker's microhardness. Scanning electron microscopy was used to show the cross-section morphologies of the composites. Silanization of diatomite and nanosized silica positively reinforced interactions between the resin matrix and the inorganic particles. The mechanical properties of the resin composites gradually increased with the addition of modified diatomite (m-diatomite). The fracture surfaces of the composites exhibited large fracture steps with the addition of m-diatomite. However, when the mass fraction of m-diatomite was greater than 21 wt.% with respect to modified nanosized silica (mOX-50) and constituted 70% of the resin composite by weight, the mechanical properties of the resin composites started to decline. Thus, the porous structure of diatomite appears to be a crucial factor to improve mechanical properties of resin composites.

Fission product behavior in HTGR fuel particles made from weak-acid resins

International Nuclear Information System (INIS)

Tiegs, T.N.; Henson, T.J.

1979-04-01

Fission product retention and behavior are of utmost importance in HTGR fuel particles. The present study concentrates on particles made from weak-acid resins, which can vary in composition from 100% UO 2 plus excess carbon to 100% UC 2 plus excess carbon. Five compositions were tested: UC 4 58 O 2 04 , UC 3 68 O 0 01 , UC 4 39 O 1 72 , UC 4 63 O 0 97 , and UC 4 14 O 1 53 . Metallographically sectioned particles were examined with a shielded electron microprobe. The distributions of the fission products were determined by monitoring characteristic x-ray lines while scanning the electron beam over the particle surface

Uranium recovery and uranium remove from acid mine waters by ion exchange resin; Remocao e recuperacao de uranio de aguas acidas de mina com resina de troca ionica

Energy Technology Data Exchange (ETDEWEB)

Nascimento, Marcos R.L. [Comissao Nacional de Energia Nuclear (CNEN), Pocos de Caldas, MG (Brazil). Coordenacao do Laborarorio; Fatibello Filho, Orlando [Sao Carlos Univ., SP (Brazil). Dept. de Quimica

1999-11-01

Ion exchange using resins is one of few processes capable of reducing contaminants in effluents to very low levels according to environmental legislation. In this study the process was used to remove and recovery uranium from acid mine waters at Pocos de Caldas-MG Uranium Mining and Milling Plant. The presence of pyrite in the waste rock piles, resulting acid drainage with several pollutants. Including uranium ranging from 6 to 14 mg/l, as sulfate complex, that can be removed by an anionic exchanger. Studies of uranium sorption without treatment, and with lime pretreatment of water to precipitate the iron and recovery uranium as commercial product, are presented. Uranium elution was done with NaCl solutions. Saline concentration and retention time were the parameters studied. the uranium decontaminations level in the effluents from acid mine water was 94%. (author) 10 refs., 6 tabs., 3 figs.

System for processing ion exchange resin regeneration waste liquid in atomic power plant

International Nuclear Information System (INIS)

Onaka, Noriyuki; Tanno, Kazuo; Shoji, Saburo.

1976-01-01

Object: To reduce the quantity of radioactive waste to be solidified by recovering and repeatedly using sulfuric acid and sodium hydroxide which constitute the ion exchange resin regeneration waste liquid. Structure: Cation exchange resin regeneration waste liquid is supplied to an anion exchange film electrolytic dialyzer for recovering sulfuric acid through separation from impurity cations, while at the same time anion exchange resin regeneration waste liquid is supplied to a cation exchange film electrolytic dialyzer for recovering sodium hydroxide through separation from impurity anions. The sulfuric acid and sodium hydroxide thus recovered are condensed by a thermal condenser and then, after density adjustment, repeatedly used for the regeneration of the ion exchange resin. (Aizawa, K.)

Kinetic Study of Esterification of Acetic Acid with n-butanol and isobutanol Catalyzed by Ion Exchange Resin

Directory of Open Access Journals (Sweden)

Amrit Pal Toor

2011-05-01

Full Text Available Esters are an important pharmaceutical intermediates and very useful perfumery agents. In this study the esterification of acetic acid with n-butanol and iso-butanol over an acidic cation exchange resin, Amberlyst 15 were carried out. The effects of certain parameters such as temperature, catalyst loading, initial molar ratio between reactants on the rate of reaction were studied. The experiments were conducted in a stirred batch reactor in the temperature range of 351.15 K to 366.15K.Variation of parameters on rate of reaction demonstrated that the reaction was intrinsically controlled.The activation energy for the esterification of acetic acid with n-butanol and iso butanol is found to be 28.45 k J/mol and 23.29 kJ/mol respectively. ©2011 BCREC UNDIP. All rights reserved.(Received: 16th December 2010, Revised: 19th March 2011; Accepted: 7th April 2011[How to Cite: A.P. Toor, M. Sharma, G. Kumar, and R. K. Wanchoo. (2011. Kinetic Study of Esterification of Acetic Acid with n-butanol and isobutanol Catalyzed by Ion Exchange Resin. Bulletin of Chemical Reaction Engineering and Catalysis, 6(1: 23-30. doi:10.9767/bcrec.6.1.665.23-30][How to Link / DOI: http://dx.doi.org/10.9767/bcrec.6.1.665.23-30 || or local: http://ejournal.undip.ac.id/index.php/bcrec/article/view/665 ] | View in 

Separation of actinium-227 from its daughter products by cationic resins technique

International Nuclear Information System (INIS)

Nastasi, M.J.C.

1976-01-01

A method for separating actinium-227 from its daughter products based on ion exchange principle is shown. Radionuclides mixture in perchloric acid 8,5 N and chloridric acid 0,5 N medium pass by a cationic resin column. Thorium-227 and actinium-227, which are retained by the resin, are eluted with nitric acid 6 N which releases actinium-227 while oxalic acid 7% is used for thorium-227 elution [pt

Accurate determination of 41Ca concentrations in spent resins from the nuclear industry by Accelerator Mass Spectrometry

International Nuclear Information System (INIS)

Nottoli, Emmanuelle; Bourlès, Didier; Bienvenu, Philippe; Labet, Alexandre; Arnold, Maurice; Bertaux, Maité

2013-01-01

The radiological characterisation of nuclear waste is essential for managing storage sites. Determining the concentration of Long‐Lived RadioNuclides (LLRN) is fundamental for their long-term management. This paper focuses on the measurement of low 41 Ca concentrations in ions exchange resins used for primary fluid purification in Pressurised Water Reactors (PWR). 41 Ca concentrations were successfully measured by Accelerator Mass Spectrometry (AMS) after the acid digestion of resin samples, followed by radioactive decontamination and isobaric suppression through successive hydroxide, carbonate, nitrate and final CaF 2 precipitations. Measured 41 Ca concentrations ranged from 0.02 to 0.03 ng/g, i.e. from 0.06 to 0.09 Bq/g. The 41 Ca/ 60 Co activity ratios obtained were remarkably reproducible and in good agreement with the current ratio used for resins management. - Highlights: • In the context of radioactive waste management, this study aimed at measuring 41 Ca in spent resins using Accelerator Mass Spectrometry. • A chemical treatment procedure was developed to quantitatively recover calcium in solution and selectively extract it. • Developed firstly on synthetic matrices, the chemical treatment procedure was then successfully applied to real resin samples. • Accelerator mass spectrometry allowed measuring concentrations of 41 Ca in spent resins as low as 0.02 ng/g of dry resin. • Final results are in agreement with current data used for spent resins management

Potentiometric titration of free acid in uranium solutions

International Nuclear Information System (INIS)

Suh, M. Y.; Kim, W. H.; Kim, J. S.; Sohn, S. C.; Eom, T. Y.; Lee, C. H.; Jeon, Y. S.; Han, S. H.

1998-02-01

Hydrolysis properties of metal cations and fundamental principles of the potentiometric titration of free acid in aqueous solutions containing metal cations were described. The published papers and reports for the alkalimetric and acidimetric titration of free acid were surveyed, and the applicability of these titration methods to the uranium and/or plutonium solutions were discussed. This technical report also includes the various results obtained from the authors' researches to establish the alkalimetric and acidimetric titration methods for the determination of free acid in nitric acid solutions containing uranium and/or oxalic acid, and aluminum. The procedure manuals used in chemical processes and the newly prepared manuals based on the authors' researches are appended. (author). 26 refs., 54 figs

Potentiometric titration of free acid in uranium solutions

Energy Technology Data Exchange (ETDEWEB)

Suh, M. Y.; Kim, W. H.; Kim, J. S.; Sohn, S. C.; Eom, T. Y.; Lee, C. H.; Jeon, Y. S.; Han, S. H.

1998-02-01

Hydrolysis properties of metal cations and fundamental principles of the potentiometric titration of free acid in aqueous solutions containing metal cations were described. The published papers and reports for the alkalimetric and acidimetric titration of free acid were surveyed, and the applicability of these titration methods to the uranium and/or plutonium solutions were discussed. This technical report also includes the various results obtained from the authors` researches to establish the alkalimetric and acidimetric titration methods for the determination of free acid in nitric acid solutions containing uranium and/or oxalic acid, and aluminum. The procedure manuals used in chemical processes and the newly prepared manuals based on the authors` researches are appended. (author). 26 refs., 54 figs.

Radiation protection by ascorbic acid in sodium alginate solutions

Energy Technology Data Exchange (ETDEWEB)

Aliste, A.J.; Mastro, N.L. Del [Center of Radiation Technology, IPEN/CNEN/SP, University City, 05508-000 Sao Paulo (Brazil)]. E-mail: ajaliste@ipen.br

2004-07-01

Alginates are gelling hydrocolloids extracted from brown seaweed used widely in the nourishing and pharmaceutical industries. As alginic acid gellification retard food entrance in the stomach alginate is an additive used in diets. The objective of this work was to study the protective action of the ascorbic acid in alginate solutions against the action of {sup 60} Co gamma radiation. One % (w/v) solutions of alginate had been used and concentrations of ascorbic acid varied from 0 to 2.5% (w/v). The solutions were irradiated with doses up to 10 kGy. Viscosity/dose relationship and the p H of the solutions at 25 Centigrade were determined. Ascorbic acid behaved as an antioxidant against radiation oxidative shock in this model system of an irradiated viscous solution. Besides its radiation protective role on alginate solutions ascorbic acid promoted a viscosity increase in the range of concentrations employed. (Author)

Radiation protection by ascorbic acid in sodium alginate solutions

International Nuclear Information System (INIS)

Aliste, A.J.; Mastro, N.L. Del

2004-01-01

Alginates are gelling hydrocolloids extracted from brown seaweed used widely in the nourishing and pharmaceutical industries. As alginic acid gellification retard food entrance in the stomach alginate is an additive used in diets. The objective of this work was to study the protective action of the ascorbic acid in alginate solutions against the action of 60 Co gamma radiation. One % (w/v) solutions of alginate had been used and concentrations of ascorbic acid varied from 0 to 2.5% (w/v). The solutions were irradiated with doses up to 10 kGy. Viscosity/dose relationship and the p H of the solutions at 25 Centigrade were determined. Ascorbic acid behaved as an antioxidant against radiation oxidative shock in this model system of an irradiated viscous solution. Besides its radiation protective role on alginate solutions ascorbic acid promoted a viscosity increase in the range of concentrations employed. (Author)

An Analytical Vacuum-Assisted Resin Transfer Molding (VARTM) Flow Model

National Research Council Canada - National Science Library

Fink, Bruce

2000-01-01

.... The analytical solution presented here provides insight into the scaling laws governing fill times and resin inlet placement as a function of the properties of the preform, distribution media, and resin...

Studies on removal of plutonium from oxalic acid containing hydrochloric acid solutions

Energy Technology Data Exchange (ETDEWEB)

Ghadse, D R; Noronha, D M; Joshi, A R [Fuel Chemistry Division, Bhabha Atomic Research Centre, Mumbai (India)

1994-06-01

Solution containing hydrochloric acid, oxalic acid and considerable quantities of plutonium may be generated while recycling of scrap produced during the metallic fuel fabrication. Plutonium from such waste is normally recovered by anion exchange method after the destruction of oxalic acid using suitable oxidising agent. Solvent extraction and ion exchange methods are being explored in this laboratory for recovery of Pu from oxalic acid containing HCl solutions without prior destruction of oxalic acid. This paper describes the results on the determination of distribution ratios for extraction of Pu(IV) from hydrochloric acid using Aliquot-336 or HDEHP under varying experimental conditions. (author). 5 refs., 5 tabs.

Method for curing alkyd resin compositions by applying ionizing radiation

International Nuclear Information System (INIS)

Watanabe, T.; Murata, K.; Maruyama, T.

1975-01-01

An alkyd resin composition is prepared by dissolving a polymerizable alkyd resin having from 10 to 50 percent of oil length into a vinyl monomer. The polymerizable alkyd resin is obtained by a half-esterification reaction of an acid anhydride having a polymerizable unsaturated group and an alkyd resin modified with conjugated unsaturated oil having at least one reactive hydroxyl group per one molecule. The alkyd resin composition thus obtained is coated on an article, and ionizing radiation is applied on the article to cure the coated film thereon. (U.S.)

Microshear bond strength of composite resins to enamel and porcelain substrates utilizing unfilled versus filled resins.

Science.gov (United States)

Najafi-Abrandabadi, Ahmad; Najafi-Abrandabadi, Siamak; Ghasemi, Amir; Kotick, Philip G

2014-11-01

Failures such as marginal discoloration and composite chipping are still the problems of tooth-colored restorations on the substrate of enamel and porcelain, which some of these problems are consequently as a result of failures in the bonding layer. Using filled resin has been recently introduced to increase the bond strength of this layer. The aim of this study was to compare the microshear bond strength (μ-SBS) of composite resins to enamel incubated in periods of 24 h and 9 months and porcelain with unfilled resin and flowable composites (filled resin). In this in vitro study, two groups of 75 enamel samples with different storage times (24 h and 9 months) and a group of 75 porcelain samples were used. They were divided into 5 experimental groups of 15 samples in each. Composite cylinders in tygon tubes were bonded on the surface of acid-etched enamel and pretreated porcelain. Wave, Wave MV, Wave HV, Grandioflow and Margin Bond were used as bonding agents. The μ-SBS was measured at the speed of 1.0 mm/min. The bond strengths were analyzed with one-way analysis of variance (ANOVA) test followed by Tukey test. P composites (filled resins) can be used instead of unfilled resins in bonding composite resins to enamel and porcelain substrates.

The reduction of sulfate ions in Musashino woody lignite and in acetone-furfural resin

Energy Technology Data Exchange (ETDEWEB)

Kimura, T.

1986-01-01

By adding a barium chloride solution to sulfur-containing woody lignite kept in water for two years, it has been confirmed that large quantities of sulfate ions are adsorbed by the lignite. Furthermore, spectroscopic measurements have confirmed the reduction of sulfate ions in an acetone-furfural resin prepared with residual sulfuric acid. These experimental results suggest the possibility of reducing sulfate ions in coal in the absence of sulfate bacteria. 2 refs.

Stability of the neurotensin receptor NTS1 free in detergent solution and immobilized to affinity resin.

Directory of Open Access Journals (Sweden)

Jim F White

2010-09-01

Full Text Available Purification of recombinant membrane receptors is commonly achieved by use of an affinity tag followed by an additional chromatography step if required. This second step may exploit specific receptor properties such as ligand binding. However, the effects of multiple purification steps on protein yield and integrity are often poorly documented. We have previously reported a robust two-step purification procedure for the recombinant rat neurotensin receptor NTS1 to give milligram quantities of functional receptor protein. First, histidine-tagged receptors are enriched by immobilized metal affinity chromatography using Ni-NTA resin. Second, remaining contaminants in the Ni-NTA column eluate are removed by use of a subsequent neurotensin column yielding pure NTS1. Whilst the neurotensin column eluate contained functional receptor protein, we observed in the neurotensin column flow-through misfolded NTS1.To investigate the origin of the misfolded receptors, we estimated the amount of functional and misfolded NTS1 at each purification step by radio-ligand binding, densitometry of Coomassie stained SDS-gels, and protein content determination. First, we observed that correctly folded NTS1 suffers damage by exposure to detergent and various buffer compositions as seen by the loss of [(3H]neurotensin binding over time. Second, exposure to the neurotensin affinity resin generated additional misfolded receptor protein.Our data point towards two ways by which misfolded NTS1 may be generated: Damage by exposure to buffer components and by close contact of the receptor to the neurotensin affinity resin. Because NTS1 in detergent solution is stabilized by neurotensin, we speculate that the occurrence of aggregated receptor after contact with the neurotensin resin is the consequence of perturbations in the detergent belt surrounding the NTS1 transmembrane core. Both effects reduce the yield of functional receptor protein.

Properties of cyclodextrins. V. Inclusion isotherm and kinetics of inclusion of benzoic acid and m-chlorobenzoic acid on b-E 25 cyclodextrin-epichlorohydrin resin

NARCIS (Netherlands)

Wiedenhof, N.; Trieling, R.G.

1971-01-01

The previous paper showed that b-E 25 resins have an affinity for aromatic compds., e.g. BZOH and m-ClC6H4CO2H; mainly the undissocd. acids are involved. The isothermal inclusion of undissocd. BZOH is described by a Langmuir isotherm, but that of m-ClC6H4CO2H follows a Freundlich isotherm. The

Inversion of the calcium isotope separation at an ion exchanger resin by variation of the LiCl electrolyte concentration

International Nuclear Information System (INIS)

Heumann, K.G.; Kloeppel, H.; Sigl, G.

1982-01-01

The calcium isotope separation at a strongly acidic exchanger resin as a function of the concentration of a LiCl solution is investigated in column experiments. Whereas an enrichment of the heavier calcium isotopes in the solution phase is found with a 3 M LiCl solution, an inverse effect is obtained with 8 M and 12 M LiCl solutions. The separation effect epsilon for the 12 M solution is found to be the highest calcium enrichment in a system without a complexing agent. The results are compared with those for other electrolyte solutions and can be explained by the anion/cation interactions. (orig.)

Extraction of cesium from acid solutions

International Nuclear Information System (INIS)

Katykhin, G.S.; Simonov, A.S.

1983-01-01

The extraction of cesium from acidic solutions is studied. Halogen-substituted carboxylic acids were chosen for the aqueous phase and nitrobenzene the diluent. The distribution coefficients are determined by the use of radioactive tracers 134 Cs and 137 Cs. It is believed that large singly charged anions of strong acids are necessary for the extraction of cesium. Metal halide acids are selected for supplying the anions

Sorption of Uranium Ions from Their Aqueous Solution by Resins Containing Nanomagnetite Particles

Directory of Open Access Journals (Sweden)

Mahmoud O. Abd El-Magied

2016-01-01

Full Text Available Magnetic amine resins composed of nanomagnetite (Fe3O4 core and glycidyl methacrylate (GMA/N,N′-methylenebisacrylamide (MBA shell were prepared by suspension polymerization of glycidyl methacrylate with N,N′-methylenebisacrylamide in the presence of nanomagnetite particles and immobilized with different amine ligands. These resins showed good magnetic properties and could be easily retrieved from their suspensions using an external magnetic field. Adsorption behaviors of uranium ions on the prepared resins were studied. Maximum sorption capacities of uranium ions on R-1 and R-2 were found to be 92 and 158 mg/g. Uranium was extracted successfully from three granite samples collected from Gabal Gattar pluton, North Eastern Desert, Egypt. The studied resins showed good durability and regeneration using HNO3.

Fiber reinforced silicon-containing arylacetylene resin composites

Directory of Open Access Journals (Sweden)

2007-12-01

Full Text Available A silicon-containing arylacetylene resin (SAR, a poly(dimethylsilyleneethynylene phenyleneethynylene (PMSEPE, was synthesized. The PMSEPE is a solid resin at ambient temperature with a softening temperature about 60°C and soluble in some solvents like tetrahydrofuran. The melt viscosity of the PMSEPE resin is less than 1 Pa•s. The resin could cure at the temperature of lower than 200°C. Fiber reinforced PMSEPE composites were prepared from prepregs which were made by the impregnation of fibers in PMSEPE resin solution. The composites exhibit good mechanical properties at room temperature and 250°C. The observation on fracture surfaces of the composites reinforced by glass fibers and carbon fibers demonstrates that the adhesion between the fibers and resin is good. The results from an oxyacetylene flame test show that the composites have good ablation performance and XRD analyses indicate that SiC forms in the residues during the ablation of the composites.

Evaluation of extractants and chelating resins in polishing actinide-contaminated waste streams

International Nuclear Information System (INIS)

Schreiber, S.B.; Dunn, S.L.; Yarbro, S.L.

1991-06-01

At the Los Alamos National Laboratory Plutonium Facility, anion exchange is used for recovering plutonium from nitric acid solutions. Although this approach recovers >99%, the trace amounts of plutonium and other actinides remaining in the effluent require additional processing. We are doing research to develop a secondary unit operation that can directly polish the effluent so that actinide levels are reduced to below the maximum allowed for facility discharge. We selected solvent extraction, the only unit operation that can meet the stringent process requirements imposed; several carbonyl and phosphoryl extractants were evaluated and their performance characterized. We also investigated various engineering approaches for solvent extraction; the most promising was a chelating resin loaded with extractant. Our research now focuses on the synthesis of malonamides, and our goal is to bond these extractants to a resin matrix. 7 refs., 12 figs., 1 tab

Carbon dioxide capture using resin-wafer electrodeionization

Science.gov (United States)

Lin, YuPo J.; Snyder, Seth W.; Trachtenberg, Michael S.; Cowan, Robert M.; Datta, Saurav

2015-09-08

The present invention provides a resin-wafer electrodeionization (RW-EDI) apparatus including cathode and anode electrodes separated by a plurality of porous solid ion exchange resin wafers, which when in use are filled with an aqueous fluid. The apparatus includes one or more wafers comprising a basic ion exchange medium, and preferably includes one or more wafers comprising an acidic ion exchange medium. The wafers are separated from one another by ion exchange membranes. The fluid within the acidic and/or basic ion exchange wafers preferably includes, or is in contact with, a carbonic anhydrase (CA) enzyme to facilitate conversion of bicarbonate ion to carbon dioxide within the acidic medium. A pH suitable for exchange of CO.sub.2 is electrochemically maintained within the basic and acidic ion exchange wafers by applying an electric potential across the cathode and anode.

A summary of methods for conditioning and immobilizing ion-exchange resins

International Nuclear Information System (INIS)

Speranzini, R.A.; Buckley, L.P.

1983-02-01

Ion-exchange resins are used in CANDU-PHW nuclear power stations to purify heavy water in the primary heat transport (PHT) and moderator systems. Two promising techniques for conditioning spent ion-exchange resins for disposal have been evaluated: direct immobilization and incineration combined with immobilization of the ash and scrubbed off-gases. When ion-exchange resins were immobilized directly, volumes of bitumen products were about 0.75 times the volumes of untreated resin, while the volumes of cement and polyester products were 2 to 3 times larger. While incinerating the resin is an extra processing step, much smaller volumes result from the latter option. Bitumen and glass product volumes were six and ten times smaller, respectively, than the volumes of untreated resin, while cement and polyester product volumes were about one-half the volume of untreated resin. Since the releases of Cs-136 by leaching were lowest for products made by immobilization in glass, PHT resins which have high concentrations of Cs-137 should be vitrified. Moderator resins which have high concentrations of C-14 should be incinerated and the ash and C-14-contaminated scrubbing solutions should be immobilized. By pretreating such resins with calcium chloride or carbon dioxide, the C-14 present on resin could be released at temperatures below the ignition temperature of the resin. The pretreatment technique reduces the amount of inactive carbon dioxide that must be scrubbed to trap the C-14. The releases of C-14 from immobilized barium hydroxide scrubbing solution were the same as releases from immobilized resin

Studies on the absorption of uranium and plutonium on macroporous anion-exchange resins from mixed solvent media

International Nuclear Information System (INIS)

Chetty, K.V.; Mapara, P.M.; Godbole, A.G.; Swarup, Rajendra

1995-01-01

The ion-exchange studies on uranium and plutonium using macroporous anion-exchange resins from an aqueous-organic solvent mixed media were carried out to develop a method for their separation. Out of the several water miscible organic solvents tried, methanol and acetone were found to be best suited. Distribution data for U(VI) and Pu(IV) for three macroporous resins Tulsion A-27(MP) (strong base), Amberlyst A-26(MP) (strong base) and Amberlite XE-270(MP) (weak base) as a function of (i) nitric acid concentration (ii) organic solvent concentration were obtained. Based on the data separation factors for Pu/U were calculated. Column experiments using Tulsion A-27(MP) from a synthetic feed (HNO 3 - methanol and HNO 3 - acetone) containing Pu and U in different ratios were carried out. Plutonium was recovered from the bulk of the actual solution generated during the dissolution of plutonium bearing fuels. The method has the advantage of loading plutonium from as low as 1M nitric acid in presence of methanol or acetone and could be used satisfactorily for its recovery from solutions containing plutonium and uranium. (author). 11 refs., 4 figs., 16 tabs

Synthesis of some Ferromagnetic Composite Resins and their Metal Removal Characteristics in Aqueous Solutions

International Nuclear Information System (INIS)

Sheha, R.R.; EI-Zahhar, A.A.

2008-01-01

In this study, a procedure for synthesis of new organic-inorganic magnetic composite resins was established. The procedure was based upon immobilization of magnetite as a ferromagnetic material within the polymeric (poly(acrylic acid acrylonitrile) and IRC-120) ion exchange resins. The produced magnetic resins were evaluated as sorbents for CI(VI). The factors influencing the sorption of Cr(Vl), e.g., ph, equilibrium time, initial concentration and temperature were studied. The sorption process was very fast initially and maximum sorption was achieved within 3 h at ph 5.1. Thc kinetics of the system have been evaluated with pseudo first order model, second order model, Elovich equation, intra-particle diffusion model and liquid film diffusion model. Chromium interaction with composite particles followed second-order kinetics with a correlation coefficient extremely high and closer to unity and rate constant (k s ) has the values 1.68 x 10 -4 and 1.9 x 10 -4 g/mg min for IRC-120-P AN-magnetite and P(AA-AN)-magnetite composites, respectively. The values of equilibrium sorption capacity (q e ) are consistent with the modeled data and attain the range 893 - 951 mg/g. Kinetically, both pore diffusion and film diffusion are participating in ruling the diffusion of CI(VI) ions. The sorption data gave good fits with Temkin and Flory-Huggins isotherm models. The isotherm parameters related to the heat of sorption are in the range 8-16 kJ mol -1 which is the range of bonding energy for ion exchange interactions and so suggest an ion exchange mechanism for removal of CI(VI) by the composite sorbents. The adsorption process was exothermic with δH in the range of -73 to -97 kJ/mol. The negative values of Gibbs free energy confirm the feasibility and the spontaneous nature of removal of CI(VI) with these novel composites

In hydrofluoric acid corrosion-resistant materials

International Nuclear Information System (INIS)

Hauffe, K.

1985-01-01

Copper, red brass (Cu-15 Zn), special treated carbon steel and chromium-nickel-molybdenum steel represent materials of high resistivity against concentrated hydrofluoric acid ( 2 O 3 ) are employed for windows in the presence of hydrogen fluoride and/or hydrofluoric acid because of their superior optical properties and their excellent corrosion resistance. Polyethylen, polypropylene and polyvinyl chloride (PVC) belong to the cheapest corrosion resistant material for container and for coatings in the presence of hydrofluoric acid. Special polyester resins reinforced by glass or graphite fibers have been successfully employed as material for production units with hydrofluoric acid containing liquids up to 330 K. By carbon reinforced epoxy resin represents a corrosion resistant coating. Because of their excellent friction and corrosion resistance against concentrated hot hydrofluoric acid and HNO 3 -HF-solutions, PTFE and polyvinylidene fluoride are used as material for valves and axles in such environment. The expensive alloys, as for instance hastelloy and monel, are substituted more and more by fiber-reinfored polyolefins, PVC and fluorine containing polymers. (orig.) [de

Spray drying of bead resins: feasibility tests

International Nuclear Information System (INIS)

Gay, R.L.; Grantham, L.F.; Jones, L.J.

1984-01-01

Rockwell International has developed a volume reduction system for low-level reactor wastes based on drying the wastes in a heated-air spray dryer. The drying of slurries of sodium sulfate, boric acid, and powdered ion exchange resins was demonstrated in previous tests. The drying of bead ion exchange resins can be especially difficult due to the relatively large size of bead resins (about 500 to 800 microns) and their natural affinity for water. This water becomes part of the pore structure of the resins and normally comprises 50 t 60 wt % of the resin weight. A 76-cm-diameter spray dryer was used for feasibility tests of spray drying of cation and anion bead resins. These resins were fed to the dryer in the as-received form (similar to dewatered resins) and as slurries. A dry, free-flowing product was produced in all the tests. The volume of the spray-dried product was one-half to one-third the volume of the as-received material. An economic analysis was made of the potential cost savings that can be achieved using the Rockwel spray dryer system. In-plant costs, transportation costs, and burial costs of spray-dried resins were compared to similar costs for disposal of dewatered resins. A typical utility producing 170 m 3 (6,000 ft 3 ) per year of dewatered resins can save $600,000 to $700,000 per year using this volume reduction system

Adsorption of 4-chlorophenol from aqueous solutions by xad-4 resin: Isotherm, kinetic, and thermodynamic analysis

International Nuclear Information System (INIS)

Bilgili, M. Sinan

2006-01-01

Removal of 4-chlorophenol (4-CP) from synthetic aqueous solutions through adsorption on Amberlite XAD-4 resin, a non-ionic macroreticular resins, under batch equilibrium experimental conditions at 298, 308 and 318 K was investigated. It is necessary to propose a suitable model to a better understanding on the mechanism of 4-CP adsorption. For this purpose, Langmiur, Freundlich, Toth, and Redlich-Peterson (RP) isotherm models were compared. The two and three parameters in the adopted adsorption isotherm models were determined by the help of MATLAB package program. It was determined that best fitted adsorption isotherm models were obtained to be in the order: Redlich-Peterson > Langmuir > Toth > Freundlich isotherms. The pseudo-second-order kinetic model provided the best correlation to the experimental results. Results of the intra-particle diffusion model show that the pore diffusion is not the only rate limiting step. The lower correlation of the data to the Bangham's equation also represents that the diffusion of the adsorbate into pores of the sorbent is not the only rate-controlling step. The thermodynamic constants of adsorption phenomena; ΔG o , ΔH o , and ΔS o were found as -4.17 (at 298 K) kJ/mol, -42.01 kJ/mol, and -0.127 kJ/(mol K), respectively. The results showed that adsorption of 4-CP on Amberlite XAD-4, a nonionic polymeric resin was exothermic and spontaneous

Mechanical properties of dental resin composites by co-filling diatomite and nanosized silica particles

Energy Technology Data Exchange (ETDEWEB)

Wang Hua; Zhu Meifang [State Key Laboratory for Modification of Chemical Fibers and Polymer Materials, Donghua University, Shanghai 201620 (China); Li Yaogang [Engineering Research Center of Advanced Glasses Manufacturing Technology, MOE, Donghua University, Shanghai 201620 (China); Zhang Qinghong, E-mail: zhangqh@dhu.edu.cn [Engineering Research Center of Advanced Glasses Manufacturing Technology, MOE, Donghua University, Shanghai 201620 (China); Wang Hongzhi, E-mail: wanghz@dhu.edu.cn [State Key Laboratory for Modification of Chemical Fibers and Polymer Materials, Donghua University, Shanghai 201620 (China)

2011-04-08

The aim of this study was to investigate the mechanical property effects of co-filling dental resin composites with porous diatomite and nanosized silica particles (OX-50). The purification of raw diatomite by acid-leaching was conducted in a hot 5 M HCl solution at 80 deg. C for 12 h. Both diatomite and nanosized SiO{sub 2} were silanized with 3-methacryloxypropyltrimethoxysilane. The silanized inorganic particles were mixed into a dimethacrylate resin. Purified diatomite was characterized by X-ray diffraction, UV-vis diffuse reflectance spectroscopy and an N{sub 2} adsorption-desorption isotherm. Silanized inorganic particles were characterized using Fourier transform infrared spectroscopy and a thermogravimetric analysis. The mechanical properties of the composites were tested by three-point bending, compression and Vicker's microhardness. Scanning electron microscopy was used to show the cross-section morphologies of the composites. Silanization of diatomite and nanosized silica positively reinforced interactions between the resin matrix and the inorganic particles. The mechanical properties of the resin composites gradually increased with the addition of modified diatomite (m-diatomite). The fracture surfaces of the composites exhibited large fracture steps with the addition of m-diatomite. However, when the mass fraction of m-diatomite was greater than 21 wt.% with respect to modified nanosized silica (mOX-50) and constituted 70% of the resin composite by weight, the mechanical properties of the resin composites started to decline. Thus, the porous structure of diatomite appears to be a crucial factor to improve mechanical properties of resin composites.

Separation of organic ion exchange resins from sludge - engineering study

International Nuclear Information System (INIS)

Duncan, J.B.

1998-01-01

This engineering study evaluates the use of physical separation technologies to separate organic ion exchange resin from KE Basin sludge prior to nitric acid dissolution. This separation is necessitate to prevent nitration of the organics in the acid dissolver. The technologies under consideration are: screening, sedimentation, elutriation. The recommended approach is to first screen the Sludge and resin 300 microns then subject the 300 microns plus material to elutriation

Study and application on lean resin converting in uranium mill

International Nuclear Information System (INIS)

Zhao Shaoxi; Huang Qijin; Zhu Shuguang; Yi Faqing; Du Wenjie

2012-01-01

The field test about sulphuric acid used to convert lean resin was finished. The results indicated sulphuric acid could replace chlorin in lean resin and could be reclaimed to desorption procedure. The consumption of NaCl decreased, the chlorin concentration of tailing decreased too. Both of uranium loss and waste water volume were reduced. The uranium concentration of tailing decreased and energy saving and emission reduction can be achieved. (authors)

Separation of organic ion exchange resins from sludge -- engineering study

Energy Technology Data Exchange (ETDEWEB)

Duncan, J.B.

1998-08-25

This engineering study evaluates the use of physical separation technologies to separate organic ion exchange resin from KE Basin sludge prior to nitric acid dissolution. This separation is necessitate to prevent nitration of the organics in the acid dissolver. The technologies under consideration are: screening, sedimentation, elutriation. The recommended approach is to first screen the Sludge and resin 300 microns then subject the 300 microns plus material to elutriation.

Density of nitric acid solutions of plutonium; Densite des solutions nitriques de plutonium

Energy Technology Data Exchange (ETDEWEB)

Guibergia, J P [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

1960-07-01

The report is intended to furnish an expression making it possible to determine the density of a nitric acid solution of plutonium. Under certain defined experimental conditions, the equation found makes it possible to deduce, for a solution whose concentration, free acidity and temperature are known, the corresponding value of the density of that solution. (author) [French] L'expose a pour but de donner une formule permettant la determination de la densite d'une solution nitrique de plutonium. Suivant certaines conditions experimentales precisees, l'equation trouvee permet, pour une solution dont la concentration, l'acidite libre nitrique et la temperature sont donnees, de deduire la valeur correspondant de la densite de cette solution. (auteur)

Fixation and separation of the elements thorium and uranium using anion exchange resins in nitrate solution; Fixation et separation des elements thorium et uranium par les resines echangeuses d'anions en milieu nitrate

Energy Technology Data Exchange (ETDEWEB)

Korgaonkar, V. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1967-10-01

The exchange of thorium and uranium between a strong base anion resin and a mixed water + ethanol solvent containing nitrate ions is studied. It is assumed that in the resin the thorium and uranium are fixed in the form of the complexes Th(NO{sub 3}){sub 6}{sup 2-} and UO{sub 2}(NO{sub 3}){sub 4}{sup 2-} in solution these elements are present in the form of complexes having the general formula: Th(NO{sub 3}){sub 6-n}{sup n-2} and UO{sub 2}(NO{sub 3}){sub 4-n}{sup n-2} It has been possible to deduce a law for the changes in the partition functions of thorium and uranium as a function of the concentrations of the various species in solution and of the complexing ion NO{sub 3}. From this has been deduced the optimum operational conditions for separating a mixture of these two elements. Finally, in these conditions, the influence of a few interfering ions has been studied: Ba, Bi, Ce, La, Mo, Pb, Zr. The method proposed can be used either as a preparation, or for the dosage of thorium by a quantitative separation. (author) [French] On etudie l'echange du thorium et de l'uranium entre une resine anion base forte et un solvant mixte eau + ethanol charge en ions nitrates. On a suppose que, dans la resine, le thorium et l'uranium sont fixes sous forme de complexes Th(NO{sub 3}){sub 6}{sup 2-} et UO{sub 2}(NO{sub 3}){sub 4}{sup 2-} en solution, ces elements sont engages dans des complexes de formule generale: Th(NO{sub 3}){sub 6-n}{sup n-2} and UO{sub 2}(NO{sub 3}){sub 4-n}{sup n-2} On a pu degager une loi de variation des coefficients de partage du thorium et de l'uranium en fonction des concentrations des diverses especes en solution et de l'anion complexant NO{sub 3}{sup -}. On en a deduit les conditions operatoires optimales necessaires pour separer les deux elements a partir de leurs melanges. Enfin, dans ces conditions, on a etudie l'influence de quelques elements genants: Ba, Bi, Ce, La, Mo, Pb, Zr. La methode preconisee peut etre

Selective recovery of a pyridine derivative from an aqueous waste stream containing acetic acid and succinonitrile with solvent impregnated resins

NARCIS (Netherlands)

Bokhove, J.; Visser, T.J.; Schuur, Boelo; de Haan, A.B.

2015-01-01

Solvent impregnated resins (SIRs) were evaluated for the recovery of pyridine derivatives from an aqueous waste-stream containing also acetic acid and succinonitrile. For this purpose, a new solvent was developed, synthesized and impregnated in Amberlite XAD4. Sorption studies were used to determine

Effect of Enamel and Dentin Surface Treatment on the Self-Adhesive Resin Cement Bond Strength.

Science.gov (United States)

Mushashe, Amanda Mahmmad; Gonzaga, Carla Castiglia; Cunha, Leonardo Fernandes da; Furuse, Adilson Yoshio; Moro, Alexandre; Correr, Gisele Maria

2016-01-01

The aim of this study was to evaluate the effect of enamel and dentin surface treatment on the micro-shear bond strength of self-adhesive cement. Seventy-two extracted third molars had their crowns embedded in acrylic resin and worn to obtain a flat enamel or dentin surface. The enamel and dentin specimens were randomly assigned to 8 groups (n=12) that were based on surface treatment (11.5% polyacrylic acid solution or no treatment), substrate condition (wet or dry) and storage period (1 day or 90 days), and treated accordingly. Cylinders (1 × 1 mm) were fabricated using self-adhesive resin cement (RelyX U200) following the manufacturer's instructions. The specimens were stored in distilled water at 37 °C for either 1 day or 90 days and subjected to micro-shear bond strength test (EMIC DL 2000 at 0.5 mm/min). After this, the failure type of the specimens was determined. Data were subjected to statistical analysis (a=0.05). According to the results, the 11.5% polyacrylic acid application decreased the bond strength in both enamel and dentin samples. The moist groups showed higher bond strength than the dry ones, regardless of the substrate and surface treatment. Storage period did not influence bond strength. In conclusion, surface treatment with 11.5% polyacrylic acid and absence of moisture decreased the bond strength of the resin-cement (RelyU200), regardless of the storage period.

Supercritical water oxidation of ion exchange resins: Degradation mechanisms

Energy Technology Data Exchange (ETDEWEB)

Leybros, A.; Roubaud, A. [CEA Marcoule, DEN DTCD SPDE LFSM, F-30207 Bagnols Sur Ceze (France); Guichardon, P. [Ecole Cent Marseille, F-13451 Marseille 20 (France); Boutin, O. [Aix Marseille Univ, UMR CNRS 6181, F-13545 Aix En Provence 4 (France)

2010-07-01

Spent ion exchange resins are radioactive process wastes for which there is no satisfactory industrial treatment. Supercritical water oxidation could offer a viable treatment alternative to destroy the organic structure of resins and contain radioactivity. IER degradation experiments were carried out in a continuous supercritical water reactor. Total organic carbon degradation rates in the range of 95-98% were obtained depending on operating conditions. GC-MS chromatography analyses were carried out to determine intermediate products formed during the reaction. Around 50 species were identified for cationic and anionic resins. Degradation of poly-styrenic structure leads to the formation of low molecular weight compounds. Benzoic acid, phenol and acetic acid are the main compounds. However, other products are detected in appreciable yields such as phenolic species or heterocycles, for anionic IERs degradation. Intermediates produced by intramolecular rearrangements are also obtained. A radical degradation mechanism is proposed for each resin. In this overall mechanism, several hypotheses are foreseen, according to HOO center dot radical attack sites. (authors)

The coacervation of aqueous solutions of tetraalkylammonium halides

International Nuclear Information System (INIS)

Mugnier de Trobriand, Anne.

1979-09-01

The coacervation of aqueous solutions of tatraalkylammonium halides in the presence of not of inorganic halides and acids has been studied, considering thermodynamic and spectroscopic aspects. The importance of dispersion forces as well as forces resulting from hydrophobic hydration has been assessed. The analogy between these systems and anionic ion exchange resins has been shown especially for Uranium VI extraction [fr

A STUDY ON ADSORPTION AND DESORPTION BEHAVIORS OF 14C FROM A MIXED BED RESIN

Directory of Open Access Journals (Sweden)

SEUNG-CHUL PARK

2014-12-01

Full Text Available Spent resin waste containing a high concentration of 14C radionuclide cannot be disposed of directly. A fundamental study on selective 14C stripping, especially from the IRN-150 mixed bed resin, was carried out. In single ion-exchange equilibrium isotherm experiments, the ion adsorption capacity of the fresh resin for non-radioactive HCO3− ion, as the chemical form of 14C, was evaluated as 11mg-C/g-resin. Adsorption affinity of anions to the resin was derived in order of NO3− > HCO3− ≥ H2PO4−. Thus the competitive adsorption affinity of NO3− ion in binary systems appeared far higher than that of HCO3− or H2PO4−, and the selective desorption of HCO3− from the resin was very effective. On one hand, the affinity of Co2+ and Cs+ for the resin remained relatively higher than that of other cations in the same stripping solution. Desorption of Cs+ was minimized when the summation of the metal ions in the spent resin and the other cations in solution was near saturation and the pH value was maintained above 4.5. Among the various solutions tested, from the view-point of the simple second waste process, NH4H2PO4 solution was preferable for the stripping of 14C from the spent resin.

Mechanical Properties of Surface-Charged Poly(Methyl Methacrylate as Denture Resins

Directory of Open Access Journals (Sweden)

Sang E. Park

2009-01-01

Full Text Available The aim of this study was to examine the mechanical properties of a new surface-modified denture resin for its suitability as denture base material. This experimental resin is made by copolymerization of methacrylic acid (MA to poly(methyl methacrylate (PMMA to produce a negative charge. Four experimental groups consisted of Orthodontic Dental Resin (DENTSPLY Caulk as a control and three groups of modified PMMA (mPMMA produced at differing ratios of methacrylic acid (5 : 95, 10 : 90, and 20 : 80 MA : MMA. A 3-point flexural test using the Instron Universal Testing Machine (Instron Corp. measured force-deflection curves and a complete stress versus strain history to calculate the transverse strength, transverse deflection, flexural strength, and modulus of elasticity. Analysis of Variance and Scheffe Post-test were performed on the data. Resins with increased methacrylic acid content exhibited lower strength values for the measured physical properties. The most significant decrease occurred as the methacrylic acid content was increased to 20% mPMMA. No significant differences at P<.05 were found in all parameters tested between the Control and 5% mPMMA.

Immobilisation of ion exchange resins in cement

International Nuclear Information System (INIS)

Howard, C.G.; Jolliffe, C.B.; Lee, D.J.

1990-09-01

The removal of activity from spent decontaminating solutions eg LOMI can be achieved using organic ion exchange resins. These resins can be successfully immobilised in cement based matrices. The optimum cement system contained 10% ordinary Portland cement 84% gg blast furnace slag, 6% microsilica with a water cement ratio of 0.5 and a dry resin loading of 36% with respect to total weight. This formulation was successfully scaled up to 200 litres giving a product with acceptable compressive strength, dimensional stability and elastic modulus. Storage of samples under water appears to have no detrimental effects on the product's properties. (author)

Immobilisation of ion exchange resins in cement

International Nuclear Information System (INIS)

Howard, C.G.; Jolliffe, C.B.; Lee, D.J.

1990-09-01

The removal of activity from spent decontaminating solutions eg LOMI can be achieved using organic ion exchange resins. These resins can be successfully immobilised in cement based matrices. The optimum cement system contained 10% ordinary Portland cement, 84% gg blast furnace slag, 6% microsilica with a water cement ratio of 0.5 and a dry resin loading of 36% with respect to total weight. This formulation was successfully scaled up to 200 litres giving a product with acceptable compressive strength, dimensional stability and elastic modulus. Storage of samples under water appears to have no detrimental effects on the products' properties. (author)

A novel application of resin in pulp in the metallurgical industry

International Nuclear Information System (INIS)

Fleming, C.A.; Cromberge, G.

1985-01-01

The results are presented of several small-scale pilot-plant investigations that demonstrate the feasibility of a resin-in-pulp process for the combined extraction of gold and uranium. Both metals are leached into an aqueous solution as anionic complexes, and, under appropriate conditions, both metal anions can be stabilized in the same solution and extracted from that solution by anion-exchange resins. Three different lead materials containing gold and uranium were tested, and several configurations for leaching and the resin-in-pulp process were examined so that the efficiency of extraction of the process could be demonsrated. The results of the various pilot-plant investigations are discussed with particular emphasis on the deportment of gold and uranium during the leaching extraction, and elution steps

Recovery of fission products from acidic waste solutions thereof

International Nuclear Information System (INIS)

Carlin, W.W.; Darlington, W.B.; Dubois, D.W.

1975-01-01

Fission products, e.g., palladium, ruthenium and technetium, are removed from aqueous, acidic waste solutions thereof. The acidic waste solution is electrolyzed in an electrolytic cell under controlled cathodic potential conditions and technetium, ruthenium, palladium and rhodium are deposited on the cathode. Metal deposit is removed from the cathode and dissolved in acid. Acid insoluble rhodium metal is recovered, dissolved by alkali metal bisulfate fusion and purified by electrolysis. In one embodiment, the solution formed by acid dissolution of the cathode metal deposit is treated with a strong oxidizing agent and distilled to separate technetium and ruthenium (as a distillate) from palladium. Technetium is separated from ruthenium by organic solvent extraction and then recovered, e.g., as an ammonium salt. Ruthenium is disposed of as waste by-product. Palladium is recovered by electrolysis of an acid solution thereof under controlled cathodic potential conditions. Further embodiments wherein alternate metal recovery sequences are used are described. (U.S.)

Viscoelastic behavior of multiwalled carbon nanotubes into phenolic resin

Energy Technology Data Exchange (ETDEWEB)

Botelho, Edson Cocchieri; Costa, Michelle Leali; Braga, Carlos Isidoro, E-mail: ebotelho@feg.unesp.br [Universidade Estadual Paulista Julio de Mesquita Filho (UNESP), Guaratingueta, SP (Brazil). Dept. de Materiais e Tecnologia; Burkhart, Thomas [Institut fuer Verbundwerkstoffe GmbH, Kaiserslautern, (Germany); Lauke, Bernd [Leibniz-Institut fuer Polymerforschung, Dresden (Germany)

2013-11-01

Nanostructured polymer composites have opened up new perspectives for multi-functional materials. In particular, carbon nanotubes (CNTs) have the potential applications in order to improve mechanical and electrical performance in composites with aerospace application. This study focuses on the viscoelastic evaluation of phenolic resin reinforced carbon nanotubes, processed by using two techniques: aqueous-surfactant solution and three roll calender (TRC) process. According to our results a relative small amount of CNTs in a phenolic resin matrix is capable of enhancing the viscoelastic properties significantly and to modify the thermal stability. Also has been observed that when is used TRC process, the incorporation and distribution of CNT into phenolic resin is more effective when compared with aqueous solution dispersion process. (author)

Synthesis of novel chitosan resin derivatized with serine moiety for the column collection/concentration of uranium and the determination of uranium by ICP-MS

International Nuclear Information System (INIS)

Oshita, Koji; Oshima, Mitsuko; Gao Yunhua; Lee, Kyue-Hyung; Motomizu, Shoji

2003-01-01

A chitosan resin derivatized with serine moiety (serine-type chitosan) was newly developed by using the cross-linked chitosan as a base material. The adsorption behavior of trace amounts of metal ions on the serine-type chitosan resin was systematically examined by packing it in a mini-column, passing a metal solution through it and measuring metal ions in the effluent by ICP-MS. The resin could adsorb a number of metal cations at pH from neutral to alkaline region, and several oxoanionic metals at acidic pH region by an anion exchange mechanism. Uranium and Cu could be adsorbed selectively at pH from acidic to alkaline region by a chelating mechanism; U could be adsorbed quantitatively even at pH 3-4. Uranium adsorbed on the resin was easily eluted with 1 M nitric acid: the preconcentration (5-, 10-, 50- and 100-fold) of U was possible. The column treatment method was used prior to the ICP-MS measurement of U in natural river, sea and tap waters; R.S.D. were 2.63, 1.13 and 1.37%, respectively. Uranium in tap water could be determined by 10-fold preconcentration: analytical result was 1.46±0.02 ppt. The resin also was applied to the recovery of U in sea water: the recovery tests for artificial and natural sea water were 97.1 and 93.0%, respectively

Application of resin in pulp technique for ion exchange separation of uranium from alkaline leachate

International Nuclear Information System (INIS)

Sreenivas, T.; Rajan, K.; Chakravorty, J.

2014-01-01

The hydrometallurgical process for the recovery of uranium from different ores uses ion exchange (IX) technique for the separation of dissolved uranium values. Conventionally, the IX process is carried out on leach solution obtained after the filtration or counter-current decantation of the leach slurries. Amongst the two types of leach pulps generated in uranium ore processing, viz acidic and alkaline, the latter one consists of predominantly fine-size pulps of higher viscosity, thus making the solid-liquid separation an arduous task. Sustained research for improvising the efficiency of various unit operations in the uranium process flowsheet have resulted in advent of new generation resins which are mechanically re-silent, posses higher exchange capacity thereby enabling separation of dissolved uranium ions from the leach pulps directly. Some of the prominent low-grade uranium ore deposits in India are hosted in acid consuming gangue matrix. These ore deposits necessitate fine grinding as well as application of alkaline leaching for the dissolution of uranium values. The leach pulps analyse 500 – 600 mg/l of U3O8 and contain total dissolved solutes (TDS) to the extent of about 50 g/l. Analysis of the characteristics of the leach pulp indicated suitability of resin-in-pulp technique for the separation of uranyl carbonate anions from the leachate. This paper describes the results of the RIP test work on alkaline leach slurry using various commercially available strong base anionic exchange resins. Parametric variation studies were conducted to establish the adsorption isotherm and sorption kinetics followed by elution of loaded uranium. Based on these results semi-continuous experiments on “carousel” mode were carried out. The results indicate superiority of gel type polystyrene based resins grafted with quaternary ammonium ion in comparison to the macro-porous resins. Semi-continuous counter-current extraction and elution tests indicated that about 98% of

Synthesis and properties of hydroxy acrylic resin with high solid content

Science.gov (United States)

Yu, Zhen; Hu, Mingguang; Cui, Han; Xiao, Jijun

2017-10-01

Manufacturers of automotive repair finishes are tending to reduce more and more the level of volatile organic compounds in their paints in order to comply with increasingly strict environmental legislation. A high solid hydroxy acrylic resin was synthesised using CARDURA E10 and a type of hydroxyacrylic acid resin, its' acid value, hydroxylvalue, viscosity, structure, morphology was measured and film-forming properties after curing were characterised. The results show that the addition of CARDURA E10 in the copolymer composition significantly reduced the viscosity of the polymer system, improved the solid content of the resin and the physical properties of the coating. The hydroxyl acrylate resin with solid content of 90% and excellent comprehensive performance were successfully prepared by controlling the initiator dosage, polymerization temperature and monomer ratio.

Solvent impregnated resin for isolation of U(VI) from industrial wastes

International Nuclear Information System (INIS)

Karve, M.; Rajgor, R.V.

2008-01-01

A solid-phase extraction method based upon impregnation of Cyanex 302 (bis(2,4,4- trimethylpentyl)mono-thio-phosphinic acid) on Amberlite XAD-2 resin is proposed for isolation of U(VI) from uranmicrolite ore tailing samples and industrial effluent samples. U(VI) was sorbed from nitric acid media on the solvent-impregnated resin (SIR) and was recovered completely with 1.0 M HCl. Based upon sorption behavior of U(VI) with Cyanex 302, it was quantitatively sorbed on the SIR in a dynamic method, while the other metal ions were not sorbed by the modified resin. The preparation of impregnated resin is simple, based upon physical interaction of the extractant and solid support, has good sorption capacity for U(VI), and is also reliable for detection of traces of U(VI). (authors)

Adsorption and removal of clofibric acid and diclofenac from water with MIEX resin.

Science.gov (United States)

Lu, Xian; Shao, Yisheng; Gao, Naiyun; Chen, Juxiang; Zhang, Yansen; Wang, Qiongfang; Lu, Yuqi

2016-10-01

This study demonstrates the use of MIEX resin as an efficient adsorbent for the removal of clofibric acid (CA) and diclofenac (DCF). The adsorption performance of CA and DCF are investigated by a batch mode in single-component or bi-component adsorption system. Various factors influencing the adsorption of CA and DCF, including initial concentration, contact time, adsorbent dosage, initial solution pH, agitation speed, natural organic matter and coexistent anions are studied. The Langmuir model can well describe CA adsorption in single-component system, while the Freundlich model gives better fitting in bi-component system. The DCF adsorption can be well fitted by the Freundlich model in both systems. Thermodynamic analyses show that the adsorption of CA and DCF is an endothermic (ΔH(o) > 0), entropy driven (ΔS(o) > 0) process and more randomness exists in the DCF adsorption process. The values of Gibbs free energy (ΔG(o)  0) for CA adsorption. The kinetic data suggest the adsorption of CA and DCF follow the pseudo-first-order model in both systems and the intra-particle is not the unique rate-limiting step. The adsorption process is controlled simultaneously by external mass transfer and surface diffusion according to the surface diffusion modified Biot number (Bis) ranging from 1.06 to 26.15. Moreover, the possible removal mechanism for CA and DCF is respectively proposed based on the ion exchange stoichiometry. Copyright © 2016 Elsevier Ltd. All rights reserved.

Effect of sodium hypochlorite and peracetic acid on the surface roughness of acrylic resin polymerized by heated water for short and long cycles.

Science.gov (United States)

Sczepanski, Felipe; Sczepanski, Claudia Roberta Brunnquell; Berger, Sandrine Bittencourt; Consani, Rafael Leonardo Xediek; Gonini-Júnior, Alcides; Guiraldo, Ricardo Danil

2014-10-01

To evaluate the surface roughness of acrylic resin submitted to chemical disinfection via 1% sodium hypochlorite (NaClO) or 1% peracetic acid (C2H4O3). The disc-shaped resin specimens (30 mm diameter ×4 mm height) were polymerized by heated water using two cycles (short cycle: 1 h at 74°C and 30 min at 100°C; conventional long cycle: 9 h at 74°C). The release of substances by these specimens in water solution was also quantified. Specimens were fabricated, divided into four groups (n = 10) depending on the polymerization time and disinfectant. After polishing, the specimens were stored in distilled deionized water. Specimens were immersed in 1% NaClO or 1% C2H4O3 for 30 min, and then were immersed in distilled deionized water for 20 min. The release of C2H4O3 and NaClO was measured via visual colorimetric analysis. Roughness was measured before and after disinfection. Roughness data were subjected to two-way ANOVA and Tukey's test. There was no interaction between polymerization time and disinfectant in influencing the average surface roughness (Ra, P = 0.957). Considering these factors independently, there were significant differences between short and conventional long cycles (P = 0.012), but no significant difference between the disinfectants hypochlorite and C2H4O3 (P = 0.366). Visual colorimetric analysis did not detect release of substances. It was concluded that there was the difference in surface roughness between short and conventional long cycles, and disinfection at acrylic resins polymerized by heated water using a short cycle modified the properties of roughness.

[Effect of resin infiltration treatment on the colour of white spot lesions].

Science.gov (United States)

Zhao, Xiaoyi; Gao, Xuejun

2014-06-01

This study aimed to evaluate the effect of resin infiltration and fluoride solution on masking different demineralized white spot lesions by assessing color change. Artificial white spot lesions were produced on 60 human molars. Each sample had at least two enamel surfaces opened (named A and B). The samples were randomly divided into groups 1, 2, and 3 according to their time of demineralization (24, 48, and 72 h). After demineralization, the A spot of each sample was treated by resin infiltration. The B spot was treated with 0.1% fluoride solution daily for 30 days. After the remineralization of the B spot, resin infiltration was used again on the B spot of each sample. Color assessment was performed by a spectrophotometer in five distinct stages: baseline, after the production of artificial caries, after resin infiltration of A spots, after 30 days of fluoride solution treatment of B spots, and after resin infiltration of remineralized B spots. Before demineralization, the L* values of spots A and B in all groups were not significantly different (P > 0.05), whereas the L* values of spots A and B were significantly increased after demineralization. The L* values of A spots recovered significantly after treatment by resin infiltration (P 0.05) after fluoride treatment compared with that after demineralization. After resin infiltration on B spots, the L* values recovered but could not reach the baseline nor the level of A spots treated by resin infiltration only. Resin infiltration is a more effective treatment for masking white spot lesions than traditional fluoride treatment. The effect of masking white spot lesions has certain relationships with the degree of demineralization and activity of the lesion.

In vivo effects of two acidic soft drinks on shear bond strength of metal orthodontic brackets with and without resin infiltration treatment.

Science.gov (United States)

Hammad, Shaza M; Enan, Enas T

2013-07-01

To evaluate the in vivo effects of two acidic soft drinks (Coca-Cola and Sprite) on the shear bond strength of metal orthodontic brackets with and without resin infiltration treatment. In addition, the enamel surface was evaluated, after debonding, using a scanning electron microscope. Sixty noncarious maxillary premolars, scheduled for extraction in 30 orthodontic patients, were used. Patients were randomly divided into two groups according to the soft drink tested (Coca-Cola or Sprite). In each group, application of resin infiltration (Icon. DMG, Hamburg, Germany) was done on one side only before bonding of brackets. Patients were told to rinse their mouth with their respective soft drink at room temperature for 5 minutes, three times a day for 3 months. Shear bond strength was tested with a universal testing machine. After shearing test, a scanning electron microscope was used to evaluate enamel erosion. Statistical analysis was performed by twoway analysis of variance followed by the least significant difference test. The Coca-Cola group without resin infiltration showed the lowest resistance to shearing forces. Scanning electron micrographs of both groups after resin application showed a significant improvement compared with results without resin use, as the enamel appeared smoother and less erosive. Pretreatment with the infiltrating resin has proved to result in a significant improvement in shear bond strength, regardless of the type of soft drink consumed.

Photochemical reactions of neptunium in nitric acid solution containing photocatalyst

International Nuclear Information System (INIS)

Fukasawa, Tetsuo; Kawamura, Fumio

1991-01-01

Photochemical oxidation and reduction behaviors of neptunium were preliminarily investigated in 3 mol/l nitric acid solution. Nitric acid of 3 mol/l simulated the high level waste solution from a spent fuel reprocessing process. Concentrations of Np(V), Np(VI) and nitrous acid were determined with a photospectrometer, and solution potential with an electrode. Without additives, Np(VI) was reduced to Np(V) by nitrous acid which was photolytically generated from nitric acid. With a scavenger for nitrous acid, Np(V) was oxidized to extractable Np(VI) by a photolytically generated oxidizing reagent which were predicted by the solution potential measurement. The reduction rate was higher than the oxidation rate because of the larger quantity and higher reactivity of nitrous acid than an oxidizing reagent. Photocatalyst was proved to be effective for the oxidation of Np(V) to Np(VI). (author)

Bio-phenolic resin from oil palm empty fruit bunches

Science.gov (United States)

Zakaria, Zuhaili; Zakaria, Sarani; Roslan, Rasidi; Chia, Chin Hua; Jaafar, Sharifah Nabihah Syed; Amran, Umar Adli

2018-04-01

Utilization of oil palm empty fruit bunches (EFB) in the production of bio-phenolic resin is an alternative way to reduce the dependency of petroleum-based phenol. In this study, resol type bio-phenolic resin (BPR) was synthesized from EFB fibers using sulfuric acid as the catalyst to produce liquefied empty fruit bunches (LEFB) followed by resinification reaction with formaldehyde in alkaline condition. The SEM image of LEFB residue showed separation of fiber bundles into individual fibers. This indicate that lignin was destroyed during the liquefaction process. The increased of formaldehyde/LEFB molar ratio has resulted an increase of viscosity, solid content and pH of the resin. The obtained FTIR spectra confirmed that functional groups of BPR resins was almost similar with commercial resin.

Zinc incorporation improves biological activity of beta-tricalcium silicate resin-based cement.

Science.gov (United States)

Osorio, Raquel; Yamauti, Monica; Sauro, Salvatore; Watson, Tim F; Toledano, Manuel

2014-11-01

Matrix metalloproteinase (MMP) inhibition may improve endodontic treatment prognosis. The purpose of this study was to determine if zinc incorporation into experimental resin cements containing bioactive fillers may modulate MMP-mediated collagen degradation of dentin. Human dentin samples untreated and demineralized using 10% phosphoric acid or 0.5 mol/L EDTA were infiltrated with the following experimental resins: (1) unfilled resin, (2) resin with Bioglass 45S5 particles (OSspray, London, UK), (3) resin with beta-tricalcium silicate particles (βTCS), (4) resin with zinc-doped Bioglass 45S5, and (5) resin with zinc-doped βTCS particles. The specimens were stored in artificial saliva (for 24 hours, 1 week, and 4 weeks) and submitted to radioimmunoassay to quantify C-terminal telopeptide. Scanning electron microscopy analysis was also undertaken on dentin samples after 4 weeks of storage. Collagen degradation was prominent both in phosphoric acid and EDTA-treated dentin. Resin infiltration strongly reduced MMP activity in demineralized dentin. Resin containing Bioglass 45S5 particles exerted higher and stable protection of collagen. The presence of zinc in βTCS particles increases MMP inhibition. Different mineral precipitation was attained in dentin infiltrated with the resin cements containing bioactive fillers. MMP degradation of dentin collagen is strongly reduced after resin infiltration of dentin. Zinc incorporation in βTCS particles exerted an additional protection against MMP-mediated collagen degradation. However, it did not occur in resin containing Bioglass 45S5 particles, probably because of the formation of phosphate-zinc compounds. Copyright © 2014 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Study on the removal of iron impurities in methanesulfonic acid tin plating bath

Science.gov (United States)

Hou-li, LIU; Jian-Jun, CHEN; Hong-Liang, PAN

2018-03-01

This thesis investigated the the influence of sodium sulfite as reducing agent on the recovery rate of tin ion. The approach is that HZ016 type cation exchange resin was used to adsorb Sn2+ and Fe2+ in electroplated tin solution first. After adsorption, the resin was removed by sulfuric acid, which was added with NaOH to adjust pH value to form precipitation and separate tin. X-ray diffraction (XRD) and energy spectrum (EDS) method were used to analyze the composition of the precipitates adjusted by pH. The results show that when the mass ratio of resin to bath is 1:2, the adsorption efficiency of resin reaches 98.3% and 97.1% respectively, and the elution efficiency of tin and iron reaches 95.1% and 94% respectively when the mass ratio of resin to eluent sulfuric acid is 1:4. Sodium sulfite was added to increase the efficiency of tin recovery by 8.1%. EDS and XRD atlas showed that after pH regulation, the main composition of the filtration precipitation was the hydroxides of tin.

Use of the 2-chlorotrityl chloride resin for microwave-assisted solid phase peptide synthesis.

Science.gov (United States)

Ieronymaki, Matthaia; Androutsou, Maria Eleni; Pantelia, Anna; Friligou, Irene; Crisp, Molly; High, Kirsty; Penkman, Kirsty; Gatos, Dimitrios; Tselios, Theodore

2015-09-01

A fast and efficient microwave (MW)-assisted solid-phase peptide synthesis protocol using the 2-chlorotrityl chloride resin and the Fmoc/tBu methodology, has been developed. The established protocol combines the advantages of MW irradiation and the acid labile 2-chlorotrityl chloride resin. The effect of temperature during the MW irradiation, the degree of resin substitution during the coupling of the first amino acids and the rate of racemization for each amino acid were evaluated. The suggested solid phase methodology is applicable for orthogonal peptide synthesis and for the synthesis of cyclic peptides. © 2015 Wiley Periodicals, Inc.

A medicated polycarboxylate cement to prevent complications in composite resin therapy

International Nuclear Information System (INIS)

Okamoto, Y.; Shintani, H.; Yamaki, M.

1990-01-01

Preparative treatment is the preferred method to protect the dentin and pulp from complications in composite resin therapy. This study investigated the in vivo effects of the polycarboxylate cement containing zinc fluoride and tannic acid in composite resin restorations. Scanning electron micrographs established that the composite resin failed to contact the axial wall. The gaps varied from 10 to 60 microns. However, this polycarboxylate cement was shown to provide excellent adaptation to dentin when used as a base and its chemical adhesion allowed it to make close contact with the unetched dentin. The newly developed electron probe x-ray microanalyzer revealed that the in vivo penetration of fluoride and zinc occurred through the dentinal tubules. When this polycarboxylate cement was used, the orifices of dentinal tubules were partially occluded, possibly with the smear layer fixed by tannic acid. In addition, by releasing the components, this polycarboxylate cement adds acid resistance to dentin and increases the resistance of dentin collagen to proteolytic enzymes. As such this polycarboxylate cement offers advantages as a base to composite resin therapy

Utilization of m-Phenylenediamine-Furfural Resin for Removal of Cu(II) from Aqueous Solution-A Thermodynamic Study

OpenAIRE

Najim, Tariq S.; Zainal, Israa G.; Ali, Dina A.

2010-01-01

m-Phenylenediamine was condensed with furfural in absence of catalyst at room temperature. The produced m-phenylenediamine-furfural resin was used for the removal of Cu(II) from aqueous solution. The pH for the optimum removal of Cu(II) was 6. The negative values of Gibbs free energy at low concentration of Cu(II) (20, 30 ppm) indicative of the spontaneous adsorption process, while, at higher Cu(II) concentration (40,50 ppm) the positive and weak values of ∆G° indicate that the process is fea...

Chemical derivation to enhance the chemical/oxidative stability of resorcinol-formaldehyde (R-F) resin

International Nuclear Information System (INIS)

Hubler, T.L.; Shaw, W.J.; Brown, G.N.; Linehan, J.C.; Franz, J.A.; Hart, T.R.; Hogan, M.O.

1996-09-01

Tank wastes at Hanford and SRS contain highly alkaline supernate solutions of conc. Na, K nitrates with large amounts of 137 Cs. It is desirable to remove and concentrate the highly radioactive fraction for vitrification. One candidate ion exchange material for removing the radiocesium is R-F resin. This report summarizes studies into synthesis and characterization of 4-derivatized R-F resins prepared in pursuit of more chemically/oxidatively robust resin. 85% 4-fluororesorcinol/15% phenol formaldehyde resin appears to have good stability in alkaline solution, although there may be some nucleophilic displacement reaction during synthesis; further studies are needed

Bond Strength of Resin Cements to Dentin Using New Universal Bonding Agents

Science.gov (United States)

2015-06-30

and acidic simplified adhesives is a well-studied phenomenon (Kanehira et al., 2006). A chemical incompatibility may occur in the oxygen-inhibited...not completely eliminate this incompatibility (Tay et al., 2003). Recently, new “universal adhesives ” have been introduced. These universal...potential incompatibilities with self-curing resin materials. Low bond strength between self-curing resin materials and acidic simplified adhesives is

Conifer Diterpene Resin Acids Disrupt Juvenile Hormone-Mediated Endocrine Regulation in the Indian Meal Moth Plodia interpunctella.

Science.gov (United States)

Oh, Hyun-Woo; Yun, Chan-Seok; Jeon, Jun Hyoung; Kim, Ji-Ae; Park, Doo-Sang; Ryu, Hyung Won; Oh, Sei-Ryang; Song, Hyuk-Hwan; Shin, Yunhee; Jung, Chan Sik; Shin, Sang Woon

2017-07-01

Diterpene resin acids (DRAs) are important components of oleoresin and greatly contribute to the defense strategies of conifers against herbivorous insects. In the present study, we determined that DRAs function as insect juvenile hormone (JH) antagonists that interfere with the juvenile hormone-mediated binding of the JH receptor Methoprene-tolerant (Met) and steroid receptor coactivator (SRC). Using a yeast two-hybrid system transformed with Met and SRC from the Indian meal moth Plodia interpunctella, we tested the interfering activity of 3704 plant extracts against JH III-mediated Met-SRC binding. Plant extracts from conifers, especially members of the Pinaceae, exhibited strong interfering activity, and four active interfering DRAs (7α-dehydroabietic acid, 7-oxodehydroabietic acid, dehydroabietic acid, and sandaracopimaric acid) were isolated from roots of the Japanese pine Pinus densiflora. The four isolated DRAs, along with abietic acid, disrupted the juvenile hormone-mediated binding of P. interpunctella Met and SRC, although only 7-oxodehydroabietic acid disrupted larval development. These results demonstrate that DRAs may play a defensive role against herbivorous insects via insect endocrine-disrupting activity.

Modified ion exchange resins - synthesis and properties. Pt. 1

Energy Technology Data Exchange (ETDEWEB)

Doescher, F.; Klein, J.; Pohl, F.; Widdecke, H.

1982-01-22

Sulfomethylated resins are prepared by polymer analogous reactions, starting from macroporous poly(styrene-co-divinylbenzene) matrices. Different reaction paths are discussed and used in the synthesis. Sulfomethylation can be achieved by reaction of a chloromethylated resin with dimethyl sulfide and sodium sulfonate or alternatively by oxidation of polymer-bound thiol groups. Both methods give high conversions as shown by IR spectra and titration of the sulfonic acid groups. Poly(1-(4-hydroxysulfomethylphenyl)ethylene) (3) is obtained by reaction of poly(1-(4-hydroxyphenyl)ethylene) (2) resin with formaldehyde/sodium sulfonate. The thermal stability, catalytic activity, and ion exchange equilibria of the sulfomethylated resin are investigated.

Roughness comparison of heat cured type of acrylic resin in disinfectant solution immersion (Immersion in a solution of alkaline peroxide and 75% Celery extract (Apium graveolens L

Directory of Open Access Journals (Sweden)

Dewi Puspitasari

2016-08-01

Full Text Available Acrylic resin denture base has the properties absorbing that affecting physical and mechanical properties. One of the physical properties of acrylic resin is surface roughness. The aim of the study was to find out the roughness effect on heat cured acrylic that was immersed in alkaline peroxide and 75% celery (Apium graveoens L extract as a disinfectant solution. The study was a true experimental and posttest with control group designed with a rectangular shape size 65 x 10 x 3.3 mm based on the ISO standard 1567, six samples were used for alkaline peroxide, celery extract 75% and aquadest group for 5 and 15 days. A Surface Roughness Tester was used for the surface roughness changes observation. The statistical test used One-way ANOVA and post hoc Bonferroni. The results of this study showed the value of roughness on 5 days for alkaline peroxide (1.51 µm is greater than celery extract (0.36µm and aquadest (0.30 µm. The soaking for 15 days in alkaline peroxide (1.52 µm is greater than 75% celery extracts (0.38 µm and aquadest (0.34 µm. Alkaline peroxide caused higher roughness value of heat cured acrylic resin than 75% celery extract.

Thermodynamic properties of aqueous solutions with citrate ions. Compressibility studies in aqueous solutions of citric acid

International Nuclear Information System (INIS)

Apelblat, Alexander; Korin, Eli; Manzurola, Emanuel

2013-01-01

Highlights: • Over a wide range of concentrations and temperatures sound velocities were measured in aqueous solutions of citric acid. • Compressibility properties of citric acid solutions are thermodynamically characterized. • Changes in the structure of water when citric acid is dissolved are discussed. -- Abstract: Sound velocities in aqueous solutions of citric acid were measured from 15 °C to 50 °C in 5 °C intervals, within the 0.1 mol · kg −1 to 5.0 mol · kg −1 concentration range. These sound velocities served to evaluate the isentropic and isothermal compressibilities, the apparent molar compressibilities, the isochoric thermal pressure coefficients, changes of the cubic expansion coefficients with pressure at constant temperature, the changes of heat capacities with volume and hydration numbers of citric acid in aqueous solutions

Long term stability of cannabis resin and cannabis extracts

DEFF Research Database (Denmark)

Lindholst, Christian

2010-01-01

  The aim of the present study was to investigate the stability of cannabinoids in cannabis resin slabs and cannabis extracts upon long-term storage. The levels of tetrahydrocannabinol (THC), cannabinol (CBN), cannabidiol (CBD) and cannabigerol (CBG) on both neutral and acidic form were measured...... stored in extracted form at room temperature the degradation rate of acidic THC increased significantly relative to resin material with concentration halve-lives of 35 and 91 days in daylight and darkness, respectively. Once cannabis material is extracted into organic solvents, care should be taken...

Microbial treatment of ion exchange resins

International Nuclear Information System (INIS)

Kouznetsov, A.; Kniazev, O.

2001-01-01

A bioavailability of ion exchange resins to a microbial destruction as one of the alternative methods of compacting used ionites from the nuclear fuel manufacturing cycle enterprises has been investigated. The bio-destruction was studied after a preliminary chemical treatment or without it. A sensitivity of the ion exchange resins (including highly acidic cationite KU-2-8) to the microbial destruction by heterotrophic and chemo-litho-trophic microorganisms under aerobic conditions was shown in principle. The biodegradation of the original polymer is possible in the presence of the water soluble fraction of the resin obtained after its treatment by Fenton reagent and accelerated in the presence of Mn-ions in optimal concentration 1-2 g of Mn per liter of medium. Thus, the process of bio-destruction of ionite polymer by heterotrophic microorganisms can be compared with the bio-destruction of lignin or humic substances. The optimum parameters of bio-destruction and microorganisms used must be different for resins with different functional groups. (authors)

Immobilization of ion-exchange resins in cement

International Nuclear Information System (INIS)

Howard, C.G.; Jolliffe, C.B.; Lee, D.J.

1991-01-01

The removal of activity from spent decontaminating solutions, can be achieved using organic ion-exchange resins. These resins can be successfully immobilized in cement-based matrices. The optimum cement system contained 10% ordinary Portland cement, 84% gg blast furnace slag, 6% microsilica with a water/cement ratio of 0.5 and a dry resin loading of 36% with respect to total weight. This formulation was successfully scaled up to 200 litres, giving a product with acceptable compressive strength, dimensional stability and elastic modulus. Storage of samples under water appears to have no detrimental effects on the product's properties. 26 tabs., 22 figs., 29 refs

Highly hydrated poly(allylamine)/silica magnetic resin

International Nuclear Information System (INIS)

Johnson, Andrew K.; Kaczor, Jozef; Han, Hongmei; Kaur, Maninder; Tian, Guoxin; Rao, Linfeng; Qiang, You; Paszczynski, Andrzej J.

2011-01-01

The creation of multifunctional nanomaterials by combining organic and inorganic components is a growing trend in nanoscience. The unique size-dependent properties of magnetic nanoparticles (MNPs) make them amenable to numerous applications such as carriers of expensive biological catalysts, in magnetically assisted chemical separation of heavy metals and radionuclides from contaminated water sources. The separation of minor actinides from high-level radionuclide waste requires a sorbent stable in acidic pH, with ease of surface functionalization, and a high capacity for binding the molecules of interest. For the described experiments, the MNPs with 50 nm average size were used (size distribution from 20 to 100 nm and an iron content of 80–90 w/w%). The MNPs that have been double coated with an initial silica coating for protection against iron solubilization and oxidation in nitric acid solution (pH 1) and a second silica/polymer composite coating incorporating partially imbedded poly(allylamine) (PA). The final product is magnetic, highly swelling, containing >95% water, with >0.5 mmol amines g −1 available for functionalization. The amine groups of the magnetic resin were functionalized with the chelating molecules diethylenetriaminepentaacetic acid (DTPA) and N,N-dimethyl-3-oxa-glutaramic acid (DMOGA) for separation of minor actinides from used nuclear fuel.

[Analysis of anatomical pieces preservation with polyester resin for human anatomy study].

Science.gov (United States)

de Oliveira, Ítalo Martins; Mindêllo, Marcela Maria Aguiar; Martins, Yasmin de Oliveira; da Silva Filho, Antônio Ribeiro

2013-01-01

To evaluate the use of polyester resin in preserving anatomical specimens for the study of human anatomy. We used 150 anatomical specimens, comprised of unfixed (fresh), fixed in 10% formalin and vascular casts of organs injected with vinyl acetate and polyester resin. The solution used consisted of polyester resin with the diluent styrene monomer and catalyst (peroxol). After embedding in this solution, models in transparent resin were obtained, allowing full observation of structures and conservation of the specimens used. upon evaluation of the specimens, we observed a high degree of transparency, which promoted a complete visualization of structures with perfect preservation of the anatomy. The average time for the completion of the embedding was 48 hours. Only 14 specimens (9.3%) were lost during the preparation. Polyester resin can be used for preserving anatomical specimens for teaching human anatomy in a practical, aesthetic and durable way.

Volumetric properties of itaconic acid aqueous solutions

International Nuclear Information System (INIS)

Nisenbaum, Alexander; Apelblat, Alexander; Manzurola, Emanuel

2012-01-01

Highlights: ► Densities of itaconic acid aqueous solutions in a wide range of concentrations and temperatures. ► The apparent molar volumes and the cubic expansion coefficients. ► The derivatives of isobaric heat capacities with respect to pressure. ► Changes in the structure of water when itaconic acid is dissolved. - Abstract: Densities of itaconic acid aqueous solutions were measured at 5 K intervals from T = (278.15 to 343.15) K. From the determined densities, the apparent molar volumes, the cubic expansion coefficients and the second derivatives of volume with respect to temperature which are interrelated with the derivatives of isobaric heat capacities with respect to pressure were evaluated. These derivatives were qualitatively correlated with the changes in the structure of water when itaconic acid is dissolved in it.

Acidities of Water and Methanol in Aqueous Solution and DMSO

Science.gov (United States)

Gao, Daqing

2009-01-01

The relative acidities of water and methanol have been a nagging issue. In gas phase, methanol is more acidic than water by 36.0 kJ/mol; however, in aqueous solution, the acidities of methanol and water are almost identical. The acidity of an acid in solution is determined by both the intrinsic gas-phase ionization Gibbs energy and the solvent…

Process for extracting uranium from phosphoric acid solutions

International Nuclear Information System (INIS)

1977-01-01

The description is given of a method for extracting uranium from phosphoric acid solutions whereby the previously oxided acid is treated with an organic solvent constituted by a mixture of dialkylphosphoric acid and trialkylphosphine oxide in solution in a non-reactive inert solvent so as to obtain de-uraniated phosphoric acid and an organic extract constituted by the solvent containing most of the uranium. The uranium is then separated from the extract as uranyl ammonium tricarbonate by reaction with ammonia and ammonium carbonate and the extract de-uraniated at the extraction stage is recycled. The extract is treated in a re-extraction apparatus comprising not less than two stages. The extract to be treated is injected at the top of the first stage. At the bottom of the first stage, ammonia is introduced counter current as gas or as an aqueous solution whilst controlling the pH of the first stage so as to keep it to 8.0 or 8.5 and at the bottom of the last stage an ammonium carbonate aqueous solution is injected in a quantity representing 50 to 80% of the stoichiometric quantity required to neutralize the dialkylphosphoric acid contained in the solvent and transform the uranium into uranyl ammonium tricarbonate [fr

Effect of Ingested Liquids on Color Change of Composite Resins.

Science.gov (United States)

Malek Afzali, Beheshteh; Ghasemi, Amir; Mirani, Asrin; Abdolazimi, Zahra; Akbarzade Baghban, Alireza; Kharazifard, Mohammad Javad

2015-08-01

Color change of composite restorations is well known to dentists. However, the effect of commonly consumed drinks on discoloration of composite resins has yet to be determined. This study sought to assess the color change of a nanofilled (Premise) and a flowable composite resin (Premise flowable) following simulated consumption of tea, cola, iron drops and multivitamin syrup. Forty disk-shaped specimens (7 mm in diameter and 2 mm thick) were fabricated from each composite resin. The baseline color values were measured according to the CIE L*a*b* system using digital imaging. The specimens of each restorative material were randomly divided into five groups (eight each) according to the storage media namely tea, cola, iron drops, multivitamin syrup or distilled water (control). The specimens were immersed in staining solutions for three hours daily over a 40-day test period. Following this, the color change values (ΔE*) were calculated. For statistical analyses, the color differences were analyzed using two-way ANOVA and Tukey's test (Pcomposite resins (P>0.05). In both composite materials, the difference among the solutions was not significant (P>0.05). Under the tested experimental conditions, both restorative materials were susceptible to discoloration by all four staining solutions. The color change values were not related to the solution or the type of material used.

Paramagnetic epoxy resin

Directory of Open Access Journals (Sweden)

E. C. Vazquez Barreiro

2017-01-01

Full Text Available This work illustrates that macrocycles can be used as crosslinking agents for curing epoxy resins, provided that they have appropriate organic functionalities. As macrocycles can complex metal ions in their structure, this curing reaction allows for the introduction of that metal ion into the resin network. As a result, some characteristic physical properties of the metallomacrocycle could be transferred to the new material. The bisphenol A diglycidyl ether (BADGE, n = 0 and hemin (a protoporphyrin IX containing the Fe(III ion, and an additional chloride ligand have been chosen. The new material has been characterized by differential scanning calorimetry (DSC, thermogravimetric analysis (TGA, Fourier Transform Infrared (FT-IR, Nuclear Magnetic Resonance (NMR, Transmission Electron Microscopy (TEM, and magnetic susceptibility measurements. Fe(III remains in the high-spin state during the curing process and, consequently, the final material exhibits the magnetic characteristics of hemin. The loss of the chlorine atom ligand during the cure of the resin allows that Fe(III can act as Lewis acid, catalyzing the crosslinking reactions. At high BADGE n = 0/hemin ratios, the formation of ether and ester bonds occurs simultaneously during the process.

Ion exchange in HCl, NH2OH x HCl and N2H4 x 2HCl solutions

International Nuclear Information System (INIS)

Tohyama, Itiro; Otozai, Kiyoteru

1977-01-01

Distribution coefficients for 73 elements have been determined by the batch method in HCl, hydroxylamine and hydrazine solutions using strongly acidic and strongly basic exchanger resins. In general, a similar behaviour was observed. In some cases, however, the kind of onium ion was of considerable influence. Hydroxylamine and hydrazine solutions are useful as a substitute for HCl in many separations, as they are easily handled and can rapidly be decomposed by nitric acid. (orig./RB) [de

Strengthening carbonate roof rock of workings by the use of resins in Karst disturbance zones

Energy Technology Data Exchange (ETDEWEB)

Timofeev, O.V.; Gerovich, E.G.

1977-12-01

Test results are given for a proposed method of injection strengthening of rock in sinkhole areas in order to stabilize the rock of mining areas. Tests were made of appropriately selected NaOH solutions to act as catalysts in the injection of resins. Relationships are given between the hardening time of the aqueous resin solutions and the concentration of the NaOH catalyst, the relationship between the viscosity of the resin solutions and the temperature at specific ratios, between the hardness of the polymer materials and age, and between the resinous mixture compression strength and its age at specific temperatures. A diagram is presented of the injection equipment, and data are presented on the number of boreholes receiving the injected resin in relation to physical measurements. The tests of the resinated areas indicate that the rock hardness of the treated zones approaches that of the fissured zones so that props with less supporting power can be used, and work safety is increased. 3 references, 6 figures, 1 table.

Behavior of copper in acidic sulfate solution: Comparison with acidic chloride

Energy Technology Data Exchange (ETDEWEB)

Tromans, D.; Silva, J.C. [Univ. of British Columbia, Vancouver, British Columbia (Canada). Dept. of Metals and Materials Engineering

1997-03-01

The anodic polarization behavior of copper in a 0.1 M sulfuric acid (H{sub 2}SO{sub 4}) + 1 M sodium sulfate (Na{sub 2}SO{sub 4}) solution (pH = 2.0) was studied at room temperature under quiescent and stirred conditions. The behavior was compared with aqueous equilibria via construction of a potential-vs-pH (E-pH) diagram for the copper-sulfate-water (Cu-SO{sub 4}{sup 2}-H{sub 2}O) system. Interpretation of the behavior was aided by comparison with aqueous equilibria and polarization studies of copper in a 0.2 M hydrochloric acid (HCl) + 1 M sodium chloride (NaCl) solution(pH = 0.8). The initial anodic dissolution region in the acidic sulfate solution exhibited Tafel behavior with a slope consistent with formation of cupric ions (Cu{sup 2+}) whose rate of formation was charge-transfer controlled. At higher potentials, limiting current density (i{sub L}) behavior was observed under E-pH conditions that were consistent with formation of a film of copper sulfate pentahydrate (CuSO{sub 4} {degree} 5H{sub 2}O). Comparison of experimental i{sub L} values with those predicted by mass transport-controlled processes, using estimates of the diffusion layer thickness obtained from the mass transfer-influenced region of apparent Tafel behavior in the acidic chloride solution, were in sufficient agreement to indicate i{sub L} was controlled by the rate of dissolution of the CuSO{sub 4} {degree} 5H{sub 2}O film via transport of Cu{sup 2+} from the film-electrolyte interface into the bulk solution.

Degradation of ion spent resin using the Fenton's reagent

International Nuclear Information System (INIS)

Araujo, Leandro Goulart de

2013-01-01

The most common method for spent radioactive ion exchange resin treatment is its immobilization in cement, which reduces the radionuclides release into the environment. Although this method is efficient, it increases considerably the final volume of the waste due to the low incorporation capacity. The objective of this work was to develop a degradation method of spent resins arising from the nuclear research reactor located at the Nuclear and Energy Research Institute (IPEN-CNEN/SP), using an Advanced Oxidation Process (AOP) with Fenton's reagents. This method would allow a higher incorporation in cement. Three different resins were evaluated: cationic, anionic and a mixture of both resins. The reactions were conducted varying the catalyst concentration (25, 50, 100 and 150 mM), the volume of hydrogen peroxide (320 to 460 mL), and three different temperatures, 50, 60 and 70 deg C. Degradation of about 98% was achieved using a 50 mM catalyst solution and 330 mL of hydrogen peroxide solution. The most efficient temperature was 60 deg C. (author)

The study of 2-acetylaminotoluene ozonolysis in acetic ACID

OpenAIRE

Галстян, Андрій Генрійович

2014-01-01

The kinetics and mechanism of ozone reaction with 2-aminotoluene and its acylated derivative in acetic acid were studied in order to determine the possibility of obtaining 2-aminobenzoic acid.It is shown that the 2-aminotoluene ozonolysis reaction in acetic acid solution runs at high speed, and preferably on the free electron pair of the amino group to form mainly resinous compounds; oxidation products by the methyl group of the substrate are not formed under these conditions. The ozone attac...

Effect of preheat repetition on color stability of methacrylate- and silorane-based composite resins.

Science.gov (United States)

Abed Kahnamouei, Mehdi; Gholizadeh, Sarah; Rikhtegaran, Sahand; Daneshpooy, Mehdi; Kimyai, Soodabeh; Alizadeh Oskoee, Parnian; Rezaei, Yashar

2017-01-01

Background. The aim of this study was to investigate the effect of preheating methacrylate- and silorane-based composite resins on their color stability up to 40 times at 55‒60°C. Methods. Seventy-six methacrylate and silorane-based composite resin samples, with a diameter of 10 mm and a height of 2 mm, were divided into 4 groups (n=19). After the samples were prepared, their color parameters were determined using a reflective spectrophotometer. The composite resin samples were separately stored in a solution of tea for 40 consecutive days. Then the samples underwent a color determination procedure again using a spectrophotometer and color changes were recorded. Finally two-way ANOVA was used to study the effect of composite temperature on its staining (Pcomposite resin samples compared to non-heated samples at P=0.005 and P=0.029 for silorane-based and Z250 composite resin samples, respectively. Results. Both composite resin type (P=0.014) and preheating (Pcomposite resin samples, up to 55‒60°C for 40 rounds, resulted in more color changes compared with unheated composite resin samples. After storage in a solution of tea the color change rate in the composite resin samples of silorane-based was higher than the Z250 composite resin samples.

[Bonding strength of resin and tooth enamel after teeth bleaching with cold plasma].

Science.gov (United States)

Zhu, Meng-meng; Wang, Guo-min; Sun, Ke; Li, Ying-long; Pan, Jie

2016-02-18

To investigate the immediate bond strength and surface structure of resin and the tooth enamel which treated by cold plasma. In the study, 40 bovine incisors were divided into two equal parts. In this sense, all enamel adhesive samples were prepared and then randomly divided into 4 groups (n =20). group 1: acid + single bond 2+resin composite (control group); group 2:beyond bleaching+ acid+single bond 2+resin composite; group 3: treated by cold plasma for 5 minutes+ acid+single bond 2+resin composite; group 4: treated by cold plasma for 5 minutes+single bond 2+resin composite. Single bond 2 bonding system and Filtek Z250 resin were used in this experiment. The shear bond strength was tested by universal testing machine. The surface of the enamel in different processes was observed by scanning electron microscope (SEM). Statistical analyses by the single factor analysis of variance and multiple pairwise comparisons were performed with SPSS 17.0 . The shear bond strength of group 4 (8.60 MPa) was significantly lower than that of the other three groups (Penamel treated by cold plasma had slight molten form, which was different from etched enamel surface.The fractured surface of group 3 was mix fracture, which was similar to the control group (group 1). Compared with the conventional clinic bleaching, immediate bond strength of resin-enamel that treated by cold plasma has not been affected.

Biodiesel purification methodology produced in the RECOPE experimental plant, using ion exchange resins

International Nuclear Information System (INIS)

Calderon Hernandez, Teresita

2016-01-01

A methodology was proposed for the biodisel purification of crude palm oil produced in a plant located on the Refinadora Costarricense de Petroleo (RECOPE) campus in Alto de Ochomogo, using ion exchange resins. A comparison between two resins was carried out: the USF C-211H, which had been acquired together with the RECOPE experimental plant and the PD206 resin, which was in the process of being acquired at the time of starting the project. The biodisel was eluted by glass columns packed with each resin, to determine the saturation of the same. The percentage of free and bound glycerin and the presence of soaps were analyzed as response variables. With the results obtained, it was determined that the PD206 resin is more efficient in the removal of glycerin, soaps and methanol than the resin USF C-211H. However, neither of the two resins diminishes the acidity of the biodisel. A biodisel sample was eluted by the PD206 resin and the quality of the obtained product was analyzed. A flash point of 145 degrees was obtained. A total acid number of 0.82 mg KOH / G was shown, no presence of water or sediment was observed. The percentage value of carbon residue was 0.01% m / m, the cloud point was 12 degrees, the density at 15 degrees was 0.8713 g / cm 3 , the viscosity at 40 degrees was 2.75 mm 2 /s; the stability to oxidation was 14.5 h, the percentage of free glycerin was 0.01% m / m and the percentage of total glycerin was 0.06% m / m, finally a percentage of Fatty Acids Methyl Esters (FAME) of 98,6%. Of the analyzed parameters, all are within the limits established in the Reglamento Tecnico Centroamericano except the acidity value, which exceeds the maximum value of 0.05 mg KOH / g sample. An economic analysis was carried out to evaluate which resin provides the best option to complete the purification process of the biodisel produced. The PD206, despite being more expensive, purifies a larger volume of biodiesel, so for a better negotiation in the purchase price, this

Saturated Resin Ectopic Regeneration by Non-Thermal Dielectric Barrier Discharge Plasma

Directory of Open Access Journals (Sweden)

Chunjing Hao

2017-11-01

Full Text Available Textile dyes are some of the most refractory organic compounds in the environment due to their complex and various structure. An integrated resin adsorption/Dielectric Barrier Discharge (DBD plasma regeneration was proposed to treat the indigo carmine solution. It is the first time to report ectopic regeneration of the saturated resins by non-thermal Dielectric Barrier Discharge. The adsorption/desorption efficiency, surface functional groups, structural properties, regeneration efficiency, and the intermediate products between gas and liquid phase before and after treatment were investigated. The results showed that DBD plasma could maintain the efficient adsorption performance of resins while degrading the indigo carmine adsorbed by resins. The degradation rate of indigo carmine reached 88% and the regeneration efficiency (RE can be maintained above 85% after multi-successive regeneration cycles. The indigo carmine contaminants were decomposed by a variety of reactive radicals leading to fracture of exocyclic C=C bond, which could cause decoloration of dye solution. Based on above results, a possible degradation pathway for the indigo carmine by resin adsorption/DBD plasma treatment was proposed.

Development of solvent-free offset ink using vegetable oil esters and high molecular-weight resin.

Science.gov (United States)

Park, Jung Min; Kim, Young Han; Kim, Sung Bin

2013-01-01

In the development of solvent-free offset ink, the roles of resin molecular weight and used solvent on the ink performance were evaluated by examining the relationship between the various properties of resin and solvent and print quality. To find the best performing resin, the soy-oil fatty acid methyl ester (FAME) was applied to the five modified-phenolic resins having different molecular weights. It is found from the experimental results that the ink made of higher molecular weight and better solubility resin gives better printability and print quality. It is because larger molecular weight resin with better solubility gives higher rate of ink transfer. From the ink application of different esters to high molecular weight resin, the best printing performance was yielded from the soy-oil fatty acid butyl ester (FABE). It is due to its high kinematic viscosity resulting in the smallest change of ink transfer weight upon multiple number of printing, which improves the stability of ink quality.

Zirconium for nitric acid solutions

International Nuclear Information System (INIS)

Yau, T.L.

1984-01-01

The excellent corrosion resistance of zirconium in nitric acid has been known for over 30 years. Recently, there is an increasing interest in using zirconium for nitric acid services. Therefore, an extensive research effort has been carried out to achieve a better understanding of the corrosion properties of zirconium in nitric acid. Particular attention is paid to the effect of concentration, temperature, structure, solution impurities, and stress. Immersion, autoclave, U-bend, and constant strain-rate tests were used in this study. Results of this study indicate that the corrosion resistance of zirconium in nitric acid is little affected by changes in temperature and concentration, and the presence of common impurities such as seawater, sodium chloride, ferric chloride, iron, and stainless steel. Moreover, the presence of seawater, sodium chloride, ferric chloride, and stainless steel has little effect on the stress corrosion craking (SCC) susceptibility of zirconium in 70% nitric acid at room temperatures. However, zirconium could be attacked by fluoride-containing nitric acid and the vapors of chloride-containing nitric acid. Also, high sustained tensile stresses should be avoided when zirconium is used to handle 70% nitric acid at elevated temperatures or > 70% nitric acid

Campuran kitosan dengan resin akrilik sebagai bahan gigi tiruan penghambat Candida albicans

Directory of Open Access Journals (Sweden)

Titik Ismiyati

2018-04-01

Full Text Available The mixture of acrylic resin and chitosan as denture material to inhibit Candida albicans. The inhibition of Candida albicans in denture resin has an important role to prevent the development of denture stomatitis. Chitosan is a natural polymer compound derived from shrimp waste which can function as an antifungal Acrylik resin cannot be mixed with chitosan. To obtain a homogeneous mixture, the mixture was added a coupling agen acrylic acid and acetone. The research objective was to study the mixture of acrylic resin and chitosan with solvent acrylic acid and acetone as a denture that can inhibit the growth of Candida albicans. Methods: The samples used discs in 10 mm diameter and 2 mm thickness, made from heat cured acrylic resin mixed with chitosan dissolved in acrylat acid and acetone. They were divided into 4 groups. Group 1 was acrylic resin without chitosan as a control, group 2, 3 and 4 were the mixture of acrylic resin and 5 ml chitosan in 0.5%, 1%, and 2% concentration respectively. The fourier transform irfrared spectroscopy (FTIR and the digital optical microscope were used to synthesize and analyze. The Kruskal Wallis was used to analyze the data. The results showed that the mixture of acrylic resin with chitosan significantly inhibited the growth of Candida albicans. Conclusion: a mixture of acrylic resins and chitosan can be fungistatic, so it can be developed as an antifungal denture material.   ABSTRAK Penghambatan Candida albicans pada gigi tiruan resin akrilik dapat memainkan peran penting dalam mencegah perkembangan denture stomatitis. Kitosan adalah senyawa polimer alam yang berasal dari limbah udang yang dapat berfungsi sebagai antijamur. Resin akrilik tidak dapat bercampur dengan kitosan. Untuk mendapatkan campuran yang homogen, campuran tersebut ditambah coupling agent asam akrilat dan aseton. Penelitian ini bertujuan untuk mengkaji campuran resin akrilik dan kitosan dan asam akrilat pelarut aseton sebagai bahan gigi

Influence of ozone and paracetic acid disinfection on adhesion of resilient liners to acrylic resin.

Science.gov (United States)

Ekren, Orhun; Ozkomur, Ahmet

2016-08-01

The aim of this study was to evaluate the effect of paracetic acid (PAA) and ozone disinfection on the tensile bond strength (TBS) of silicone-based resilient liners to acrylic resins. One hundred and twenty dumbbell shaped heat-polymerized acrylic resins were prepared. From the mid segment of the specimens, 3 mm of acrylic were grinded off and separated parts were reattached by resilient liners. The specimens were divided into 2 control (control1, control7) and 4 test groups of PAA and ozone disinfection (PAA1, PAA7, ozone1 and ozone7; n=10). While control groups were immersed in distilled water for 10 min (control1) and 7 days (control7), test groups were subjected to PAA (16 g/L) or ozone rich water (4 mg/L) for 1 cycle (10 min for PAA and 60 min for ozone) per day for 7 days prior to tensile tests. Measurements of the TBS were analyzed using 3-way ANOVA and Tukey's HSD test. Adhesive strength of Mollosil decreased significantly by application of ozone disinfection. PAA disinfection had no negative effect on the TBS values of Mollosil and Molloplast B to acrylic resin. Single application of ozone disinfection did not have any negative effect on TBS values of Molloplast B, but prolonged exposure to ozone decreased its adhesive strength. The adhesion of resilient liners to acrylic was not adversely affected by PAA disinfection. Immersion in ozonated water significantly decreased TBS of Mollosil. Prolonged exposure to ozone negatively affects adhesion of Molloplast B to denture base materials.

Effect of sodium hypochlorite and peracetic acid on the surface roughness of acrylic resin polymerized by heated water for short and long cycles

Science.gov (United States)

Sczepanski, Felipe; Sczepanski, Claudia Roberta Brunnquell; Berger, Sandrine Bittencourt; Consani, Rafael Leonardo Xediek; Gonini-Júnior, Alcides; Guiraldo, Ricardo Danil

2014-01-01

Objective: To evaluate the surface roughness of acrylic resin submitted to chemical disinfection via 1% sodium hypochlorite (NaClO) or 1% peracetic acid (C2H4O3). Materials and Methods: The disc-shaped resin specimens (30 mm diameter ×4 mm height) were polymerized by heated water using two cycles (short cycle: 1 h at 74°C and 30 min at 100°C; conventional long cycle: 9 h at 74°C). The release of substances by these specimens in water solution was also quantified. Specimens were fabricated, divided into four groups (n = 10) depending on the polymerization time and disinfectant. After polishing, the specimens were stored in distilled deionized water. Specimens were immersed in 1% NaClO or 1% C2H4O3 for 30 min, and then were immersed in distilled deionized water for 20 min. The release of C2H4O3 and NaClO was measured via visual colorimetric analysis. Roughness was measured before and after disinfection. Roughness data were subjected to two-way ANOVA and Tukey's test. Results: There was no interaction between polymerization time and disinfectant in influencing the average surface roughness (Ra, P = 0.957). Considering these factors independently, there were significant differences between short and conventional long cycles (P = 0.012), but no significant difference between the disinfectants hypochlorite and C2H4O3 (P = 0.366). Visual colorimetric analysis did not detect release of substances. Conclusion: It was concluded that there was the difference in surface roughness between short and conventional long cycles, and disinfection at acrylic resins polymerized by heated water using a short cycle modified the properties of roughness. PMID:25512737

A Novel Method for Fabricating Double Layers Porous Anodic Alumina in Phosphoric/Oxalic Acid Solution and Oxalic Acid Solution

Directory of Open Access Journals (Sweden)

Yanfang Xu

2016-01-01

Full Text Available A novel method for fabricating ordered double layers porous anodic alumina (DL-PAA with controllable nanopore size was presented. Highly ordered large pore layer with interpore distance of 480 nm was fabricated in phosphoric acid solution with oxalic acid addition at the potential of 195 V and the small pore layer was fabricated in oxalic acid solution at the potential from 60 to 100 V. Experimental results show that the thickness of large pore layer is linearly correlative with anodizing time, and pore diameter is linearly correlative with pore widening time. When the anodizing potential in oxalic acid solution was adjusted from 60 to 100 V, the small pore layers with continuously tunable interpore distance from 142 to 241 nm and pore density from 1.94×109 to 4.89×109 cm−2 were obtained. And the interpore distance and the pore density of small pore layers are closely correlative with the anodizing potential. The fabricated DL-PAA templates can be widely utilized for fabrication of ordered nanomaterials, such as superhydrophobic or gecko-inspired adhesive materials and metal or semiconductor nanowires.

Determination of degradation conditions of exchange resins containing technetium

International Nuclear Information System (INIS)

Rivera S, A.; Monroy G, F.; Quintero P, E.

2014-10-01

The quantification of Tc-99 in spent exchange resins, coming from nuclear power plants, is indispensable to define their administration. The Tc-99 is a pure beta emitter of 210000 years of half-life, volatile and of a high mobility in water and soil. For this reason, the objective of this work is to establish a digestion method of ionic exchange resins containing technetium that retains more than 95% of this radioisotope. Mineralization tests were carried out of a resin Amberlite IRN-150 by means of an oxidation heat, in acid medium, varying the resin mass, the medium volume, the media type, the temperature and the digestion time. The digested samples were analyzed by gas chromatography to estimate the grade of their degradation. The 99m Tc was used as tracer to determine the technetium percentage recovered after mineralizing the resin. The digestion process depends on the temperature and the resin mass. At higher temperature better mineralization of samples and to greater resin mass to a constant temperature, less degradation of the resin. The spectra beta of the 99m Tc and 99 Tc are presented. (Author)

Application of radioactive tracers in upgradation of industrial grade ion exchange resin (Amberlite IRA-400)

International Nuclear Information System (INIS)

Lokhande, R.S.; Singare, P.U.

1998-01-01

The exchange rates of ion exchange are determined by application of 131 I as a tracer isotope. The exchange study carried out in this investigation deals with understanding the effectiveness of ion exchange resin (in iodide form) Amberlite IRA-400 at different concentrations of potassium iodide solution (electrolyte) with temperature of solution varying from 27-48 degC by keeping amount of ion exchange resin constant (1.0 g). The exchange study is also carried out by varying amount of ion exchange resins, for fixed temperature (27.0 degC) and for fixed concentration of potassium iodide solution (0.005 M). (author)

Biocompatibility of acrylic resin after being soaked in sodium hypochlorite

Directory of Open Access Journals (Sweden)

Nike Hendrijatini

2009-06-01

Full Text Available Background: Acrylic resin as basic material for denture will stay on oral mucosa for a very long time. The polymerization of acrylic resin can be performed by conventional method and microwave, both produce different residual monomer at different toxicity. Acrylic resin can absorb solution, porous and possibly absorb disinfectantt as well, that may have toxic reaction with the tissue. Sodium Hypochlorite as removable denture disinfectant can be expected to be biocompatible to human body. The problem is how biocompatible acrylic resin which has been processed by conventional method and microwave method after being soaked in sodium hypochlorite solution. Purpose: The aim of this study was to understand in vitro biocompatibility of acrylic resin which has polimerated by conventional method and microwave after being soaked in sodium hypochlorite using tissue culture. Methods: Four groups of acrylic resin plate were produced, the first group was acrylic resin plate with microwave polymeration and soaked in sodium hypochlorite, the second group was acrylic resin plate with microwave polymeration but not soaked, the thirdwas one with conventional method and soaked and the last group was one with conventional method but not soaked, and in 1 control group. Each group consists of 7 plates. Biocompatibility test was performed in-vitro on each material using fibroblast tissue culture (BHK-21 cell-line. Result: The percentage between living cells and dead cells from materials which was given acrylic plate was wounted. The data was analyzed statistically with T test. Conclusion: The average value of living cells is higher in acrylic resin poimerization using microwave method compared to conventional method, in both soaked and non soaked (by sodium hypochlorite group. This means that sodium hypochlorite 0.5% was biocompatible to the mouth mucosa as removable denture disinfectant for 10 minutes soaking and washing afterwards.

Potential agents for removal of actinides from waste solutions

International Nuclear Information System (INIS)

Romanovski, V.V.; Whisenhunt, D.W.; Veeck, A.C.; Andersen, W.A.; Hoffman, D.C.; Jide, X.; White, D.; Raymond, K.N.

1996-01-01

The uptake of Th(IV) from nitric acid and hydrochloric acid solutions by chelating ion exchange resins containing catechol, 1,2- hydroxypyridinone (1,2-HOPO) and 3,4-hydroxypyridinone (3,4-HOPO) functional groups, has been investigated. These polystyrene based materials show excellent kinetics for uptake of Th(IV) and have a high loading capacity. Liquid/liquid extractants have also been synthesized by addition of lipophilic side chains to the chelating groups (1,2-HOPO; 3,4-HOPO; 3,2-HOPO; catecholamide; terephthalamide). The initial evaluation of the extraction properties has been carried out

Investigations on the oxidation of nitric acid plutonium solutions with ozone

International Nuclear Information System (INIS)

Boehm, M.

1983-01-01

The reaction of ozone with nitric acid Pu solutions was studied as a function of reaction time, acid concentration and Pu concentration. Strong nitric acid Pu solutions are important in nuclear fuel element production and reprocessing. The Pu must be converted into hexavalent Pu before precipitation from the homogeneous solution together with uranium-IV, ammonia and CO 2 in the form of ammonium uranyl/plutonyl carbonate (AUPuC). Formation of a solid phase during ozonation was observed for the first time. The proneness to solidification increases with incrasing plutonium concentrations and with decreasing acid concentrations. If the formation of a solid phase during ozonation of nitric acid Pu solutions cannot be prevented, the PU-IV oxidation process described is unsuitable for industrial purposes as Pu solutions in industrial processes have much higher concentrations than the solutions used in the present investigation. (orig./EF) [de

Waste acid/metal solution reduction and recovery by vacuum distillation

International Nuclear Information System (INIS)

Jones, E.O.; Wilcox, W.A.; Johnson, N.T.; Bowdish, F.W.

1995-01-01

Processes involving distillation under reduced pressure were developed at the Pacific Northwest Laboratory several years ago to recover spent acid solutions generated during the manufacture of nuclear fuel for the N-Reactor at the Hanford site. Following construction and testing of a pilot-plant, the technology was licensed to Viatec Recovery Systems, Inc. for commercialization. The technology developed included specialized distillation and rectification of volatile acids, removal of water and/or volatile acid from sulfuric acid, and precipitation of salts. A key feature of the Waste Acid Detoxification and Reclamation (WADR) technology is the development and use of advanced thermoplastic and fluoropolymer materials of construction in all critical process equipment. The technology was then expanded to include crystallization to recover metal salts for possible reuse. Economic and environmental advantages of the procedures include recovery of acids for reuse, simplification or elimination of the disposal of waste solutions, and possible recovery of metals. Industries expected to benefit from such applications include galvanizing, electroplating, sand leaching and any where metals are cleaned in acid solutions. Currently a modular system has been assembled for recovery of several different spent acid solutions

Corrosion control of vanadium in aqueous solutions by amino acids

International Nuclear Information System (INIS)

El-Rabiee, M.M.; Helal, N.H.; El-Hafez, Gh.M. Abd; Badawy, W.A.

2008-01-01

The electrochemical behavior of vanadium in amino acid free and amino acid containing aqueous solutions of different pH was studied using open-circuit potential measurements, polarization techniques and electrochemical impedance spectroscopy (EIS). The corrosion current density, i corr , the corrosion potential, E corr and the corrosion resistance, R corr , were calculated. A group of amino acids, namely, glycine, alanine, valine, histidine, glutamic and cysteine has been investigated as environmentally safe inhibitors. The effect of Cl - on the corrosion inhibition efficiency especially in acid solutions was investigated. In neutral and basic solutions, the presence of amino acids increases the corrosion resistance of the metal. The electrochemical behavior of V before and after the corrosion inhibition process has shown that some amino acids like glutamic acid and histidine have promising corrosion inhibition efficiency at low concentration (≅25 mM). The inhibition efficiency (η) was found to depend on the structure of the amino acid and the constituents of the corrosive medium. The corrosion inhibition process is based on the adsorption of the amino acid molecules on the metal surface and the adsorption process follows the Freundlich isotherm. The adsorption free energy for valine on V in acidic solutions was found to be -9.4 kJ/mol which reveals strong physical adsorption of the amino acid molecules on the vanadium surface