Renewable energy from agro-residues in China. Solid biofuels and biomass briquetting technology

Energy Technology Data Exchange (ETDEWEB)

Chen, Longjian; Han, Lujia [Center for Biomass Resource Utilization, College of Engineering, China Agricultural University (East Campus), 17 Qing-Hua-Dong-Lu, Hai-Dian District, Beijing 100083 (China); Xing, Li [Service Center for Trading Technology Service, Chinese Academy of Agricultural Mechanization Sciences, Beijing 100083 (China)

2009-12-15

China has the abundant agro-residue resources, producing more than 630 million tons of agro-residues in 2006, and amounting to about 20% of total energy consumption in rural areas. Efficient utilization of enormous agro-residues resource is crucial for providing bioenergy, releasing risk of environmental pollution, and increasing farmers' income. The paper presented the feasibility of densified solid biofuels technology for utilizing agro-residues in China. The output and distribution of agro-residues in recent 10 years, the R and D of briquetting technology, and the market of densified solid biofuels from agro-residues in China have been analyzed. The result indicated that the abundant agro-residue resources can provide the economical and sustainable raw material for densified solid biofuels development in China. The R and D of briquetting technology at present can strongly support the large scale production of densified solid biofuels. With continued improvement and cost reduction of briquetting technology, along with the support of nation energy policy on biomass energy, the market of densified solid biofuels from agro-residues in China will be more fully deployed. Based on the above mentioned key factors, development of densified solid biofuels from agro-residues in China will be promising and feasible. (author)

Renewable energy from agro-residues in China. Solid biofuels and biomass briquetting technology

International Nuclear Information System (INIS)

Chen, Longjian; Han, Lujia; Xing, Li

2009-01-01

China has the abundant agro-residue resources, producing more than 630 million tons of agro-residues in 2006, and amounting to about 20% of total energy consumption in rural areas. Efficient utilization of enormous agro-residues resource is crucial for providing bioenergy, releasing risk of environmental pollution, and increasing farmers' income. The paper presented the feasibility of densified solid biofuels technology for utilizing agro-residues in China. The output and distribution of agro-residues in recent 10 years, the R and D of briquetting technology, and the market of densified solid biofuels from agro-residues in China have been analyzed. The result indicated that the abundant agro-residue resources can provide the economical and sustainable raw material for densified solid biofuels development in China. The R and D of briquetting technology at present can strongly support the large scale production of densified solid biofuels. With continued improvement and cost reduction of briquetting technology, along with the support of nation energy policy on biomass energy, the market of densified solid biofuels from agro-residues in China will be more fully deployed. Based on the above mentioned key factors, development of densified solid biofuels from agro-residues in China will be promising and feasible. (author)

Influence of treatment by vibration in residual stress generated in the laser welding of HSLA and IF steels

International Nuclear Information System (INIS)

Chuvas, T.C.; Fonseca, M.P. Cindra; Castello, D.A.

2010-01-01

The stress relieving treatment by vibration is a new technology under development, which has many advantages over thermal methods. In this work was analyzed the surface residual stress generated in the laser welding of biphasic HSLA and IF steels, both used in the automotive industry. Residual stresses were measured by X-ray diffraction, by the sen 2 Ψ method. Residual stresses generated in the welding of the samples were tensile at all points measured. After welding, the samples were submitted to the mechanical vibration treatment. Some samples presented a significant reduction in the stress values. The welded joints were also characterized by optical microscopy. (author)

Performance of mechanical biological treatment of residual municipal waste in Poland

Science.gov (United States)

den Boer, Emilia; Jędrczak, Andrzej

2017-11-01

The number and capacity of mechanical-biological treatment (MBT) plants in Europe increased significantly in the past two decades as a response to the legal obligation to limit the landfilling of biodegradable waste in landfills and to increase recycling and energy recovery from waste. The aim of these plants is to prepare residual municipal waste for recovery and disposal operations, including especially separation and stabilization of the easily biodegradable fraction (the biofraction). The final products of MBP technology are recyclables, stabilate, high calorific fraction which is used for the production of refuse derived fuel (RDF) and the remaining residual fraction. The shares of the output fractions, especially of the recyclables and RDF determine the overall efficiency of MBT technology in diverting waste from landfills. In this paper results of an assessment of one exemplary MBT plant are provided. The analysis was performed within a comparative study in which 20 selected MBT plants in Poland were subject to a detailed analysis, focusing, both at the design parameters as well as operational ones. The selected plant showed relatively higher overall materials recovery efficiency. With the view to circular economy targets, increased automation of the mechanical waste treatment will be required to support achieving high level diversion from landfills. The study reviled that stabilisation of biofraction should be improved by a better control of process conditions, especially moisture content.

Determination of properties of clean coal technology post-process residue

Directory of Open Access Journals (Sweden)

Agnieszka Klupa

2016-01-01

Full Text Available This article presents the possibilities of using modern measuring devices to determine the properties of process residues (Polish acronym: UPP. UPP was taken from the combustion process from a power plant in Silesia. Determining the properties of UPP is the basis for making decisions about its practical application, for example, as a raw material to obtain useful products such as: pozzolan, cenosphere or zeolite, for which there is demand. The development of advanced technology and science has given rise to modern and precise research tools that contribute to the development of appropriate methods to assess the properties of post-process residue. For this study the following were used: scanning electron microscope with EDS microanalysis and an analyzer for particle size-, shape- and number- analysis. The study conducted confirms the effectiveness of SEM analysis to determine the properties of post-process residue from Clean Coal Technologies (CCT. The results obtained are an introduction to further research on the determination of properties of CCT post-process residue. Research to determine the properties of CCT post-process residue only began relatively recently.

Surgical treatment for residual or recurrent strabismus

Directory of Open Access Journals (Sweden)

Tao Wang

2014-12-01

Full Text Available Although the surgical treatment is a relatively effective and predictable method for correcting residual or recurrent strabismus, such as posterior fixation sutures, medial rectus marginal myotomy, unilateral or bilateral rectus re-recession and resection, unilateral lateral rectus recession and adjustable suture, no standard protocol is established for the surgical style. Different surgical approaches have been recommended for correcting residual or recurrent strabismus. The choice of the surgical procedure depends on the former operation pattern and the surgical dosages applied on the patients, residual or recurrent angle of deviation and the operator''s preference and experience. This review attempts to outline recent publications and current opinion in the management of residual or recurrent esotropia and exotropia.

Technology for NPP decantate treatment realized at Kola NPP

International Nuclear Information System (INIS)

Stakhiv, Michael; Avezniyazov, Slava; Savkin, Alexander; Fedorov, Denis; Dmitriev, Sergei; Kornev, Vladimir

2007-01-01

At Moscow SIA 'Radon' jointly with JSC 'Alliance Gamma', the technology for NPP Decantate Treatment was developed, tested and realized at Kola NPP. This technology consists of dissolving the salt residue and subsequent treatment by ozonization, separation of the deposits formed from ozonization and selective cleaning by ferro-cyanide sorbents. The nonactive salt solution goes to an industrial waste disposal site or a repository specially developed at NPP sites for 'exempt waste' products by IAEA classification. This technology was realized at Kola NPP in December 2006 year. At this time more than 1000 m 3 of decantates log time stored are treated. It allows solving very old problem to empty decantates' tanks at NPPs in environmentally safe manner and with high volume reduction factor. (authors)

Residual learning rates in lead-acid batteries: Effects on emerging technologies

International Nuclear Information System (INIS)

Matteson, Schuyler; Williams, Eric

2015-01-01

The low price of lead-acid, the most popular battery, is often used in setting cost targets for emerging energy storage technologies. Future cost reductions in lead acid batteries could increase investment and time scales needed for emerging storage technologies to reach cost-parity. In this paper the first documented model of cost reductions for lead-acid batteries is developed. Regression to a standard experience curve using 1989–2012 data yield a poor fit, with R 2 values of 0.17 for small batteries and 0.05 for larger systems. To address this problem, battery costs are separated into material and residual costs, and experience curves developed for residual costs. Depending on the year, residual costs account for 41–86% of total battery cost. Using running-time averages to address volatility in material costs, a 4-year time average experience curve for residual costs yield much higher R 2 , 0.78 for small and 0.74 for large lead-acid batteries. The learning rate for residual costs in lead-acid batteries is 20%, a discovery with policy implications. Neglecting to consider cost reductions in lead-acid batteries could result in failure of energy storage start-ups and public policy programs. Generalizing this result, learning in incumbent technologies must be understood to assess the potential of emerging ones. -- Highlights: •We analyze potential cost reductions in lead-acid batteries. •Modified experience curve for non-material costs gives good empirical fit. •Historical learning rate for non-material costs from 1985–2012 is 19–24%. •Progress in incumbent technology raises barrier to new entrants

Thermal treatment of solid residues from WtE units: A review

International Nuclear Information System (INIS)

Lindberg, Daniel; Molin, Camilla; Hupa, Mikko

2015-01-01

Highlights: • We review the thermal treatment methods for ashes and residues from WtE plants. • We review the results from extensive laboratory work on vitrification, melting and vaporization of ash. • We analyze the results from the extensive patent literature on thermal treatment. • We review industrial concepts for thermal treatment of ash. - Abstract: Thermal treatment methods of bottom ash, fly ash and various types of APC (air pollution control) residues from waste-to-energy plants can be used to obtain environmentally stable material. The thermal treatment processes are meant to reduce the leachability of harmful residue constituents, destroy toxic organic compounds, reduce residue volume, and produce material suitable for utilization. Fly ash and APC residues often have high levels of soluble salts, particularly chlorides, metals such as cadmium, lead, copper and zinc, and trace levels of organic pollutants such as dioxins and furans. Different thermal treatment methods can be used to either decompose or stabilize harmful elements and compounds in the ash, or separate them from the ash to get a material that can be safely stored or used as products or raw materials. In the present paper, thermal treatment methods, such as sintering, vitrification, and melting have been reviewed. In addition to a review of the scientific literature, a survey has been made of the extensive patent literature in the field

Thermal treatment of solid residues from WtE units: A review

Energy Technology Data Exchange (ETDEWEB)

Lindberg, Daniel, E-mail: daniel.lindberg@abo.fi; Molin, Camilla, E-mail: camilla.molin@abo.fi; Hupa, Mikko, E-mail: mikko.hupa@abo.fi

2015-03-15

Highlights: • We review the thermal treatment methods for ashes and residues from WtE plants. • We review the results from extensive laboratory work on vitrification, melting and vaporization of ash. • We analyze the results from the extensive patent literature on thermal treatment. • We review industrial concepts for thermal treatment of ash. - Abstract: Thermal treatment methods of bottom ash, fly ash and various types of APC (air pollution control) residues from waste-to-energy plants can be used to obtain environmentally stable material. The thermal treatment processes are meant to reduce the leachability of harmful residue constituents, destroy toxic organic compounds, reduce residue volume, and produce material suitable for utilization. Fly ash and APC residues often have high levels of soluble salts, particularly chlorides, metals such as cadmium, lead, copper and zinc, and trace levels of organic pollutants such as dioxins and furans. Different thermal treatment methods can be used to either decompose or stabilize harmful elements and compounds in the ash, or separate them from the ash to get a material that can be safely stored or used as products or raw materials. In the present paper, thermal treatment methods, such as sintering, vitrification, and melting have been reviewed. In addition to a review of the scientific literature, a survey has been made of the extensive patent literature in the field.

Combining physico-chemical analysis with a Daphnia magna bioassay to evaluate a recycling technology for drinking water treatment plant waste residuals.

Science.gov (United States)

Chen, Ting; Xu, Yongpeng; Zhu, Shijun; Cui, Fuyi

2015-12-01

Recycling water treatment plant (WTP) waste residuals is considered to be a feasible method to enhance the efficiency of pollutant removal. This study also evaluated the safety and water quality of a pilot-DWTP waste residuals recycling technology by combining physical-chemistry analysis with a Daphnia magna assay. The water samples taken from each treatment step were extracted and concentrated by XAD-2 resin and were then analyzed for immobilization and enzyme activity with D. magna. The measured parameters, such as the dissolve organic carbon (DOC), UV254 and THM formation potential (THMFPs) of the recycling process, did not obviously increase over 15 days of continuous operation and were even lower than typical values from a conventional process. The extract concentration ranged from 0 to 2 Leq/ml as measured on the 7th and 15th days and the immobilization of D. magna exposed to water treated by the recycling process was nearly equivalent to that of the conventional process. Both the superoxide dismutase (SOD) and the catalase (CAT) activity assay indicated that a lower dose of water extract (0.5, 1, 1.5 Leq/ml) could stimulate the enzyme activity of D. magna, whereas a higher dose (2 Leq/ml at the sampling point C3, R3, R4 ) inhibits the activity. Moreover, the SOD and CAT activity of D. magna with DOC and UV254 showed a strong concentration-effect relationship, where the concentration range of DOC and UV254 were 4.1-16.2 mg/L and 0.071-4.382 cm(-1), respectively. The results showed that there was no statistically significant difference (p>0.05) between the conventional and recycling treatment processes and the toxicity of water samples in the recycling process did not increase during the 15-day continuous recycling trial. Copyright © 2015 Elsevier Inc. All rights reserved.

Electrochemical treatment of evaporated residue of soak liquor generated from leather industry

International Nuclear Information System (INIS)

Boopathy, R.; Sekaran, G.

2013-01-01

Highlights: • Electrochemical treatment of evaporated residue of soak liquor (ERSL) generated in Tannery. • Copper coating on electrode surface and horizontal mounting of electrodes for ERSL treatment. • Electrochemical oxidation of organic pollutants under high saline condition. • The treated solution may be evaporated to dryness to get NaCl salt for hide/skin preservation. -- Abstract: The organic and suspended solids present in soak liquor, generated from leather industry, demands treatment. The soak liquor is being segregated and evaporated in solar evaporation pans/multiple effect evaporator due to non availability of viable technology for its treatment. The residue left behind in the pans/evaporator does not carry any reuse value and also faces disposal threat due to the presence of high concentration of sodium chloride, organic and bacterial impurities. In the present investigation, the aqueous evaporated residue of soak liquor (ERSL) was treated by electrochemical oxidation. Graphite/graphite and SS304/graphite systems were used in electrochemical oxidation of organics in ERSL. Among these, graphite/graphite system was found to be effective over SS304/graphite system. Hence, the optimised conditions for the electrochemical oxidation of organics in ERSL using graphite/graphite system was evaluated by response surface methodology (RSM). The mass transport coefficient (k m ) was calculated based on pseudo-first order rate kinetics for both the electrode systems (graphite/graphite and SS304/graphite). The thermodynamic properties illustrated the electrochemical oxidation was exothermic and non-spontaneous in nature. The calculated specific energy consumption at the optimum current density of 50 mA cm −2 was 0.41 kWh m −3 for the removal of COD and 2.57 kWh m −3 for the removal of TKN

Eviromental Economic and Technological Residues Management Demands: An Optimization Tool.

Directory of Open Access Journals (Sweden)

Marisa Soares Borges

2012-12-01

Full Text Available Industrial residues management is a very demanding task since many different goals must be achieved. The combination of different approaches used by people from different stuff is very challenging activity that can misuse the residues potential value and applicability. An interactive WEB base tool, to integrate different sectors and overcome residues management difficulties will be presented. The system must be loaded with all data concerning the residue life cycle, and through data integration and modeling routine will give the best alternative as output. As wider and complete the system data becomes, by information loading from differen t segment, more efficient the residues management becomes. The user friendly tool will encourage the participation of industries, labs and research institutions to obtain qualified information about industrial residues inventory, raw materials recovery, characteristics, treatment and alternative uses, to achieve residues management sustainability.

Distillery spent wash: Treatment technologies and potential applications

International Nuclear Information System (INIS)

Mohana, Sarayu; Acharya, Bhavik K.; Madamwar, Datta

2009-01-01

Distillery spent wash is the unwanted residual liquid waste generated during alcohol production and pollution caused by it is one of the most critical environmental issue. Despite standards imposed on effluent quality, untreated or partially treated effluent very often finds access to watercourses. The distillery wastewater with its characteristic unpleasant odor poses a serious threat to the water quality in several regions around the globe. The ever-increasing generation of distillery spent wash on the one hand and stringent legislative regulations of its disposal on the other has stimulated the need for developing new technologies to process this effluent efficiently and economically. A number of clean up technologies have been put into practice and novel bioremediation approaches for treatment of distillery spent wash are being worked out. Potential microbial (anaerobic and aerobic) as well as physicochemical processes as feasible remediation technologies to combat environmental pollution are being explored. An emerging field in distillery waste management is exploiting its nutritive potential for production of various high value compounds. This review presents an overview of the pollution problems caused by distillery spent wash, the technologies employed globally for its treatment and its alternative use in various biotechnological sectors

Thermal treatment of solid residues from WtE units: a review.

Science.gov (United States)

Lindberg, Daniel; Molin, Camilla; Hupa, Mikko

2015-03-01

Thermal treatment methods of bottom ash, fly ash and various types of APC (air pollution control) residues from waste-to-energy plants can be used to obtain environmentally stable material. The thermal treatment processes are meant to reduce the leachability of harmful residue constituents, destroy toxic organic compounds, reduce residue volume, and produce material suitable for utilization. Fly ash and APC residues often have high levels of soluble salts, particularly chlorides, metals such as cadmium, lead, copper and zinc, and trace levels of organic pollutants such as dioxins and furans. Different thermal treatment methods can be used to either decompose or stabilize harmful elements and compounds in the ash, or separate them from the ash to get a material that can be safely stored or used as products or raw materials. In the present paper, thermal treatment methods, such as sintering, vitrification, and melting have been reviewed. In addition to a review of the scientific literature, a survey has been made of the extensive patent literature in the field. Copyright © 2015 Elsevier Ltd. All rights reserved.

Build Rocky Flats Environmental Technology site production prototype modular treatment system for stand alone core capability for residue unpack, sort, assay, repack

International Nuclear Information System (INIS)

Hildner, R.A.; Zygmunt, S.J.

1997-01-01

This document describes a portable and modular suit of equipment that upfront and near-term accomplishes a sorting process that documents and removes Rocky Flats Environmental Technology Site (RFETS) residue and waste from site inventory

Selenium-Water Treatment Residual Adsorption And Characterization

Science.gov (United States)

Aluminum-based water treatment residuals (WTR) have the ability to adsorb tremendous quantities of soil-borne P, and have been shown to adsorb other anions, such as As (V), As (III), and ClO4-. Environmental issues associated with Se in the Western US led us to study W...

Plant residues--a low cost, effective bioremediation treatment for petrogenic hydrocarbon-contaminated soil.

Science.gov (United States)

Shahsavari, Esmaeil; Adetutu, Eric M; Anderson, Peter A; Ball, Andrew S

2013-01-15

Petrogenic hydrocarbons represent the most commonly reported environmental contaminant in industrialised countries. In terms of remediating petrogenic contaminated hydrocarbons, finding sustainable non-invasive technologies represents an important goal. In this study, the effect of 4 types of plant residues on the bioremediation of aliphatic hydrocarbons was investigated in a 90 day greenhouse experiment. The results showed that contaminated soil amended with different plant residues led to statistically significant increases in the utilisation rate of Total Petroleum Hydrocarbon (TPH) relative to control values. The maximum TPH reduction (up to 83% or 6800 mg kg(-1)) occurred in soil mixed with pea straw, compared to a TPH reduction of 57% (4633 mg kg(-1)) in control soil. A positive correlation (0.75) between TPH reduction rate and the population of hydrocarbon-utilising microorganisms was observed; a weaker correlation (0.68) was seen between TPH degradation and bacterial population, confirming that adding plant materials significantly enhanced both hydrocarbonoclastic and general microbial soil activities. Microbial community analysis using Denaturing Gradient Gel Electrophoresis (DGGE) showed that amending the contaminated soil with plant residues (e.g., pea straw) caused changes in the soil microbial structure, as observed using the Shannon diversity index; the diversity index increased in amended treatments, suggesting that microorganisms present on the dead biomass may become important members of the microbial community. In terms of specific hydrocarbonoclastic activity, the number of alkB gene copies in the soil microbial community increased about 300-fold when plant residues were added to contaminated soil. This study has shown that plant residues stimulate TPH degradation in contaminated soil through stimulation and perhaps addition to the pool of hydrocarbon-utilising microorganisms, resulting in a changed microbial structure and increased alkB gene

Simulation of Distortion and Residual Stress Development During Heat Treatment of Steel Castings

Energy Technology Data Exchange (ETDEWEB)

Beckermann, Christoph; Carlson, Kent

2011-07-22

of the Navy-C ring (a classical test shape for heat treatment experiments) for several carbon and low alloy steels in order to generate data necessary to validate the code. The predicted distortions were in reasonable agreement with the experimentally measured values. However, the final distortions in the castings were small, making it difficult to determine how accurate the predictions truly are. It is recommended that further validation of the software be performed with the aid of additional experiments with large production steel castings that experience significant heat treatment distortions. It is apparent from this research that the mechanical properties of the bonded sand used for cores and sand molds are key in producing accurate stress simulation results. Because of this, experiments were performed to determine the temperature-dependent elastic modulus of a resin-bonded sand commonly utilized in the steel casting industry. The elastic modulus was seen to vary significantly with heating and cooling rates. Also, the retained room temperature elastic modulus after heating was seen to degrade significantly when the sand was heated above 125°C. The elastic modulus curves developed in this work can readily be utilized in casting simulation software. Additional experiments with higher heating rates are recommended to determine the behavior of the elastic modulus in the sand close to the mold-metal interface. The commercial heat treatment residual stress and distortion code, once fully validated, is expected to result in an estimated energy savings of 2.15 trillion BTU's/year. Along with these energy savings, reduction of scrap and improvement in casting yield will result in a reduction of the environmental emissions associated with the melting and pouring of the metal which will be saved as a result of this technology.

Advances in surface treatments: Technology, applications, effects

International Nuclear Information System (INIS)

Niku-Lari, A.

1987-01-01

An international handbook has been produced to include all aspects of residual stresses, including the theoretical background, effects of residual stresses, measurement and calculation and quantitative assessment of residual stress effects. Techniques for altering residual stresses, particularly surface treatments, are discussed. Up to date information on the state of the art is presented. (UK)

Drawing a Transductive Ecosophy in Process: Technological Arts, Residual Matter, Associated Milieus

Directory of Open Access Journals (Sweden)

Gisèle Trudel

2015-06-01

Full Text Available Drawing a Transductive Ecosophy in Process: Technological Arts, Residual Matter, Associated Milieus by Gisèle Trudel. NANO: New American Notes Online, Issue 7: The Aesthetics of Trash - nanocrit.com. This text examines the tetralogy of media artworks about residual matter produced by Ælab between 2008 and 2014. Taking its own title as a diagram (Deleuze and Guattari Mille Plateaux, it charts and builds on the processes of these artworks, elucidating their relations to materiality, philosophy and technicity. Technological research-creation becomes in these instances a transdisciplinary aesthetic act, emerging from an ecology of practices that combine humans, non-humans and waste matter in an effort to increase attentiveness in actions.

Anaerobic treatment of solid and liquid residues. Papers

International Nuclear Information System (INIS)

Maerkl, H.; Stegmann, R.

1994-01-01

Anaerobic processes are getting increasing attention in the disposal of liquid waste of the food industry and chemical industry and solid organic residues of the municipal sector. The main advantages of anaerobic processes are the favourable energy balance and the comparatively small volume of new biomass produced. There are new satisfactory technical solutions for nearly all problems encountered in practice. A conference on ''Anaerobic treatment of solid and liquid residues'' was held on 2-4 November 1994. The state of the art and new developments were presented in lectures by experts from research and practice. (orig.) [de

Fact Sheet for Friction Materials Manufacturing Facilities Residual Risk and Technology Review

Science.gov (United States)

proposed amendments to the National Emission Standards for Hazardous Air Pollutants (NESHAP) for Friction Materials Manufacturing Facilities to address the results of the residual risk and technology review

Effects of processing treatment on pesticide residues in fruits and their products

International Nuclear Information System (INIS)

Mao Xuefei; Jiao Bining; Fu Chenmei; Qian Yongzhong; Wang Jing

2008-01-01

The influence of processing treatments on pesticide residues in fruits and their products was reviewed. The effects on pesticide residues and relative control treatments for each processing step, including peeling, washing, sterilization, juicing, clarification, filtration, drying and fermentation, were discussed, respectively. Meanwhile we analyzed the future development prospectin of this field, in order to provide some suggestions for commercial fruit industry and consumers' health. (authors)

Selenium Adsorption To Aluminum-Based Water Treatment Residuals

Science.gov (United States)

Aluminum-based water treatment residuals (WTR) can adsorb water-and soil-borne P, As(V), As(III), and perchlorate, and may be able to adsorb excess environmental selenium. WTR, clay minerals, and amorphous aluminum hydroxide were shaken for 24 hours in selenate or selenite solut...

Characterisation of some South African water treatment residues ...

African Journals Online (AJOL)

2005-07-03

Jul 3, 2005 ... Land application of water treatment residue (WTR) the by-product from the production of potable water, is becoming the preferred ... were analysed for some physical (particle size distribution, particle density and plant available water) and chemical attributes ...... for Industrial Wastes – Theory and Practice.

Treatment of the acid mine drainage residue for uranium recovery

International Nuclear Information System (INIS)

Dias, M.M.; Horta, D.G.; Fukuma, H.T.; Villegas, R.A.S.; Carvalho, C.H.T. de; Silva, A.C. da

2017-01-01

Acid mine drainage (AMD) is a process that occurs in many mining that have sulfide ores. With water and oxygen, several metals are oxidized, one example being uranium. At the mine pit of the Osamu Utsumi Mine located at INB - Caldas and in two other boot-wastes (mining waste pile), AMD is present and currently, without a technological solution. The acidic water present in the pit is treated with hydrated lime, generating water for disposal and an alkaline residue called calcium diuranate - DUCA. The DUCA has a concentration of approximately 0.32% U 3 O 8 , which makes interesting the development of a process for extracting that metal. One of the processes that can be used is leaching. For this study, it was decided to evaluate the alkaline leaching to extract the uranium present in the residue. It is necessary to optimize operational parameters for the process: percentage of solids, concentration of leaching agent in solution, temperature and reaction time. With these parameters, it is possible to improve the leaching so that the largest amount of uranium is extracted from the sample, to help solve the environmental impact caused by the wastewater from the treatment of acid waters and, in addition, to give an economical destination for this metal that is contained in the deposited DUCA

The effect of sludge water treatment plant residuals on the properties of compressed brick

Science.gov (United States)

Shamsudin, Shamrul-Mar; Shahidan, S.; Azmi, M. A. M.; Ghaffar, S. A.; Ghani, M. B. Abdul; Saiful Bahari, N. A. A.; Zuki, S. S. M.

2017-11-01

The focus of this study is on the production of compressed bricks which contains sludge water treatment plant (SWTP) residuals obtained from SAJ. The main objective of this study is to utilise and incorporate discarded material (SWTP) in the form of residual solution to produce compressed bricks. This serves as one of the recycling efforts to conserve the environment. This study determined the optimum mix based on a mix ratio of 1:2:4 (cement: sand: soil) in the production of compressed bricks where 5 different mixes were investigated i. e. 0%, 5%, 10%, 20%, and 30% of water treatment plant residue solution. The production of the compressed bricks is in accordance with the Malaysian Standard MS 7.6: 1972 and British Standard BS 3921: 1985 - Compressive Strength & Water Absorption. After being moulded and air dried, the cured bricks were subjected to compression tests and water absorption tests. Based on the tests conducted, it was found that 20% of water treatment plant residue solution which is equivalent to 50% of soil content replacement with a mix composition of [10: cement] [20: sand] [20: soil] [20: water treatment plant residue solution] is the optimum mix. It was also observed that the bricks containing SWTP residuals were lighter in weight compared to the control specimens

Relaxation of residual stress in MMC after combined plastic deformation and heat treatment

International Nuclear Information System (INIS)

Bruno, G.; Ceretti, M.; Girardin, E.; Giuliani, A.; Manescu, A.

2004-01-01

Neutron Diffraction shows that plastic pre-deformation and heat treatments have opposite effects on the residual stress in Al-SiC p composites. The thermal micro residual stress is relaxed or even reversed by pre-strains above 0.2%, but restored by heat treatments. The sense of relaxation changes above 400 deg. C (the mixing temperature)

INFLUENCE OF MACHINING TECHNOLOGIES ON VALUES OF RESIDUAL STRESSES OF OXIDE CUTTING CERAMICS

Directory of Open Access Journals (Sweden)

Jakub Němeček

2017-07-01

Full Text Available Currently, the intensive development of engineering ceramic and effort to replace sintered carbides as cutting materials are in progress. With the development of the sintering technology it is now possible to produce compact ceramic cutting samples with very good mechanical properties. The advantage of these materials is their easy accessibility and low purchase price. In this work, the influence of the finishing machine technology on the values of surface residual stresses of cutting ceramic samples Al2O3+TiC were studying. The samples were supplied by Moscow State University of Technology STANKIN. Measurements made in the X-ray diffraction laboratory at the Department of solid state engineering were performed for both the phases. The influence of the parameters of machining to residual stresses was studied and the resulting values were compared with each other.

Electrochemical treatment of evaporated residue of soak liquor generated from leather industry.

Science.gov (United States)

Boopathy, R; Sekaran, G

2013-09-15

The organic and suspended solids present in soak liquor, generated from leather industry, demands treatment. The soak liquor is being segregated and evaporated in solar evaporation pans/multiple effect evaporator due to non availability of viable technology for its treatment. The residue left behind in the pans/evaporator does not carry any reuse value and also faces disposal threat due to the presence of high concentration of sodium chloride, organic and bacterial impurities. In the present investigation, the aqueous evaporated residue of soak liquor (ERSL) was treated by electrochemical oxidation. Graphite/graphite and SS304/graphite systems were used in electrochemical oxidation of organics in ERSL. Among these, graphite/graphite system was found to be effective over SS304/graphite system. Hence, the optimised conditions for the electrochemical oxidation of organics in ERSL using graphite/graphite system was evaluated by response surface methodology (RSM). The mass transport coefficient (km) was calculated based on pseudo-first order rate kinetics for both the electrode systems (graphite/graphite and SS304/graphite). The thermodynamic properties illustrated the electrochemical oxidation was exothermic and non-spontaneous in nature. The calculated specific energy consumption at the optimum current density of 50 mA cm(-2) was 0.41 kWh m(-3) for the removal of COD and 2.57 kWh m(-3) for the removal of TKN. Copyright © 2013 Elsevier B.V. All rights reserved.

Remediation of water pollution caused by pharmaceutical residues based on electrochemical separation and degradation technologies: a review.

Science.gov (United States)

Sirés, Ignasi; Brillas, Enric

2012-04-01

In the last years, the decontamination and disinfection of waters by means of direct or integrated electrochemical processes are being considered as a very appealing alternative due to the significant improvement of the electrode materials and the coupling with low-cost renewable energy sources. Many electrochemical technologies are currently available for the remediation of waters contaminated by refractory organic pollutants such as pharmaceutical micropollutants, whose presence in the environment has become a matter of major concern. Recent reviews have focused on the removal of pharmaceutical residues upon the application of other important methods like ozonation and advanced oxidation processes. Here, we present an overview on the electrochemical methods devised for the treatment of pharmaceutical residues from both, synthetic solutions and real pharmaceutical wastewaters. Electrochemical separation technologies such as membrane technologies, electrocoagulation and internal micro-electrolysis, which only isolate the pollutants from water, are firstly introduced. The fundamentals and experimental set-ups involved in technologies that allow the degradation of pharmaceuticals, like anodic oxidation, electro-oxidation with active chlorine, electro-Fenton, photoelectro-Fenton and photoelectrocatalysis among others, are further discussed. Progress on the promising solar photoelectro-Fenton process devised and further developed in our laboratory is especially highlighted and documented. The abatement of total organic carbon or reduction of chemical oxygen demand from contaminated waters allows the comparison between the different methods and materials. The routes for the degradation of the some pharmaceuticals are also presented. Copyright © 2011 Elsevier Ltd. All rights reserved.

Fiscal 2000 achievement report. Development of technologies for waste treatment and recycling (Development of technologies for appropriate treatment of air bags); 2000 nendo haikibutsu recycle kanren gijutsu kaihatsu seika hokokusho. Air bag tekisei shori gijutsu no kaihatsu nado

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

A centralized treatment process respecting environmental protection and safety for unused air bags aboard disused automobiles is developed. In concrete terms, a heating facility owned by Daicel Chemical Industries, Ltd., is used, which includes an apparatus for examining exhaust gas dioxins and an exhaust gas treatment apparatus and, with this facility, studies are made for appropriately treating waste gas and waste water to be generated when air bag modules undergo centralized heating. Endeavors in fiscal 2000 center about (1) the development of waste gas treatment technologies, (2) development of waste water treatment technologies, (3) chemical analysis of waste water sludge, dusts and air bag residues, and (4) the study of appropriate treatment of non-azide air bag modules. As to the development of exhaust gas treatment technology, it was proved that the exhaust gas treatment system consisting of secondary incineration furnace, exhaust gas cooling tower and bag filter worked effectively. (NEDO)

Effect of cryogenic treatment on distribution of residual stress in case carburized En 353 steel

International Nuclear Information System (INIS)

Bensely, A.; Venkatesh, S.; Mohan Lal, D.; Nagarajan, G.; Rajadurai, A.; Junik, Krzysztof

2008-01-01

The effect of cryogenic treatment on the distribution of residual stress in the case carburized steel (En 353) was studied using X-ray diffraction technique. Two types of cryogenic treatment: shallow cryogenic treatment (193 K) and deep cryogenic treatment (77 K) were adopted, as a supplement to conventional heat treatment. The amount of retained austenite in conventionally heat-treated, shallow cryogenically treated and deep cryogenically treated samples was found to be 28%, 22% and 14%, respectively. The conventionally heat-treated, shallow cryogenically treated and deep cryogenically treated samples in untempered condition had a surface residual stress of -125 MPa, -115 MPa and -235 MPa, respectively. After tempering the conventionally heat-treated, shallow cryogenically treated and deep cryogenically treated samples had a surface residual stress of -150 MPa, -80 MPa and -80 MPa, respectively. A comparative study of the three treatments revealed that there was an increase in the compressive residual stress in steel that was subjected to cryogenic treatment prior to tempering. The experimental investigation revealed that deep cryogenically treated steel when subjected to tempering has undergone a reduction in compressive residual stress. Such stress relieving behaviour was mainly due to the increased precipitation of fine carbides in specimens subjected to DCT with tempering

Prediction of residual metabolic activity after treatment in NSCLC patients

International Nuclear Information System (INIS)

Rios Velazquez, Emmanuel; Aerts, Hugo J.W.L.; Oberije, Cary; Ruysscher, Dirk De; Lambin, Philippe

2010-01-01

Purpose. Metabolic response assessment is often used as a surrogate of local failure and survival. Early identification of patients with residual metabolic activity is essential as this enables selection of patients who could potentially benefit from additional therapy. We report on the development of a pre-treatment prediction model for metabolic response using patient, tumor and treatment factors. Methods. One hundred and one patients with inoperable NSCLC (stage I-IV), treated with 3D conformal radical (chemo)-radiotherapy were retrospectively included in this study. All patients received a pre and post-radiotherapy fluorodeoxyglucose positron emission tomography-computed tomography FDG-PET-CT scan. The electronic medical record system and the medical patient charts were reviewed to obtain demographic, clinical, tumor and treatment data. Primary outcome measure was examined using a metabolic response assessment on a post-radiotherapy FDG-PET-CT scan. Radiotherapy was delivered in fractions of 1.8 Gy, twice a day, with a median prescribed dose of 60 Gy. Results. Overall survival was worse in patients with residual metabolic active areas compared with the patients with a complete metabolic response (p=0.0001). In univariate analysis, three variables were significantly associated with residual disease: larger primary gross tumor volume (GTVprimary, p=0.002), higher pre-treatment maximum standardized uptake value (SUV max , p=0.0005) in the primary tumor and shorter overall treatment time (OTT, p=0.046). A multivariate model including GTVprimary, SUV max , equivalent radiation dose at 2 Gy corrected for time (EQD2, T) and OTT yielded an area under the curve assessed by the leave-one-out cross validation of 0.71 (95% CI, 0.65-0.76). Conclusion. Our results confirmed the validity of metabolic response assessment as a surrogate of survival. We developed a multivariate model that is able to identify patients at risk of residual disease. These patients may benefit from

Demonstration of New Technologies Required for the Treatment of Mixed Waste Contaminated with {ge}260 ppm Mercury

Energy Technology Data Exchange (ETDEWEB)

Morris, M.I.

2002-02-06

The Resource Conservation and Recovery Act (RCRA) defines several categories of mercury wastes, each of which has a defined technology or concentration-based treatment standard, or universal treatment standard (UTS). RCRA defines mercury hazardous wastes as any waste that has a TCLP value for mercury of 0.2 mg/L or greater. Three of these categories, all nonwastewaters, fall within the scope of this report on new technologies to treat mercury-contaminated wastes: wastes as elemental mercury; hazardous wastes with less than 260 mg/kg [parts per million (ppm)] mercury; and hazardous wastes with 260 ppm or more of mercury. While this report deals specifically with the last category--hazardous wastes with 260 ppm or more of mercury--the other two categories will be discussed briefly so that the full range of mercury treatment challenges can be understood. The treatment methods for these three categories are as follows: Waste as elemental mercury--RCRA identifies amalgamation (AMLGM) as the treatment standard for radioactive elemental mercury. However, radioactive mercury condensates from retorting (RMERC) processes also require amalgamation. In addition, incineration (IMERC) and RMERC processes that produce residues with >260 ppm of radioactive mercury contamination and that fail the RCRA toxicity characteristic leaching procedure (TCLP) limit for mercury (0.20 mg/L) require RMERC, followed by AMLGM of the condensate. Waste with <260 ppm mercury--No specific treatment method is specified for hazardous wastes containing <260 ppm. However, RCRA regulations require that such wastes (other than RMERC residues) that exceed a TCLP mercury concentration of 0.20 mg/L be treated by a suitable method to meet the TCLP limit for mercury of 0.025 mg/L. RMERC residues must meet the TCLP value of {ge}0.20 mg/L, or be stabilized and meet the {ge}0.025 mg/L limit. Waste with {ge}260 ppm mercury--For hazardous wastes with mercury contaminant concentrations {ge}260 ppm and RCRA

Alternatives of Treatment and Final Disposition of the Solid Hospital residuals

International Nuclear Information System (INIS)

Meza Monge, K.

1998-01-01

The current handling, treatment and final disposition of the hospital solid waste in Costa Rica are considered inadequate or at least insufficient. This situation represents a serious danger for the population's health and the environment, because they are exposed to infectious agents, toxic substances and even radioactive products that are generated among the residuals of the centers of health. This work, alternatives propose for the treatment and adequate final disposition of the solid waste produced in the hospitals of the country. They take into consideration the characteristics that present these residuals, the advantages and disadvantages of each one of the existent techniques and the technical and economic possibilities of the country. For this purpose, in first instance, a revision about the properties, the quality and the quantity of the solid waste produced by the national hospital centers was carried out. Also, a diagnostic of the current situation of the treatment and final disposition of these residuals in some of the most important hospitals of the country, as well as of the possibilities of physical space with that they count on was carried out. Then, the existent different treatment techniques and final disposition for the solid waste that comes from the centers of health are described, as well as their advantages and disadvantages and a comparative analysis of the same ones is carried out. The objective is completed, since alternatives of treatment and final disposition that are considered appropriate for this type of residuals are planned. Nevertheless, in the future, more detailed investigations and studies of feasibility, with the purpose of developing handling programs and elimination of the solid waste for each one of the hospital centers in Costa Rica should be carried out. (Author) [es

Treatment of Residual Sodium and Sodium Potassium from Fast Reactors. Review of Recent Accomplishments, Challenges and Technologies

International Nuclear Information System (INIS)

2015-08-01

In addition to the usual radiation and conventional hazards present during the decommissioning of disused nuclear installations, the presence of residual sodium or the alloy sodium potassium — used in primary, secondary and support systems in reactors using liquid metal as a coolant — presents additional technical, safety and cost challenges for decommissioning. This results from the propensity of these materials to react exothermically with water and moisture in the air potentially resulting in toxic and explosive reactionsThis publication discusses a variety of treatment methods to be considered when dismantling components that still contain residual quantities of sodium or sodium potassium, several of which were presented as contributed papers to the IAEA session during the 5. International Conference and Exhibition on Decommissioning Challenges, in Avignon, France, 7–11 April 2013. The publication provides a synthesis of information presented during the session, which was developed further at a consultants meeting held in Vienna, 2–6 December 2013. Decommissioning challenges faced at eight different facilities in five different countries are discussed, as well as the achievements and lessons learned that are of value to the worldwide decommissioning community

Dynamic integrated assessment of bioenergy technologies for energy production utilizing agricultural residues: An input–output approach

International Nuclear Information System (INIS)

Song, Junnian; Yang, Wei; Higano, Yoshiro; Wang, Xian’en

2015-01-01

Highlights: • A dynamic input–output model is developed with bioenergy technologies complemented. • Availability of agricultural residues for bioenergy technologies is evaluated. • Trends in electricity and biofuel production are simulated dynamically. • Net profit and GHG mitigation contribution of bioenergy technologies are assessed. • Combustion power generation and briquette fuel are more advantageous. - Abstract: In order to facilitate regional agricultural residue utilization for energy production through bioenergy technologies, a dynamic input–output model is developed to estimate and assess the energy, economic and environmental performances of industrialization of five bioenergy technologies within a 15-year time horizon. Electricity and solid, gaseous and liquid biofuels are energy products of bioenergy technologies. Bioenergy technologies are complemented into regional input–output framework and combined with socioeconomic activities aided by their bottom-up economic and energy parameters. The simulation results for the target area indicate that the agricultural residues available for bioenergy technologies could amount to 55.16 million t, facilitating to 8.38 million t coal-equivalent bioenergy production by 2025. A 3.1% net reduction in accumulative greenhouse gas emission compared with the “business as usual” case could be achieved owing to substitution of fossil energy with electricity and biofuels produced by bioenergy technologies. From energy production, economic benefits and greenhouse gas mitigation three aspects integratedly, direct-combustion power generation and briquette fuel are more advantageous in the target area. The quantified energy, economic and environmental performances of bioenergy technologies are expected to give recommendations for their industrial development.

Gas composition of sludge residue profiles in a sludge treatment reed bed between loadings

DEFF Research Database (Denmark)

Larsen, Julie Dam; Nielsen, Steen M; Scheutz, Charlotte

2017-01-01

Treatment of sludge in sludge treatment reed bed systems includes dewatering and mineralization. The mineralization process, which is driven by microorganisms, produces different gas species as by-products. The pore space composition of the gas species provides useful information on the biological...... processes occurring in the sludge residue. In this study, we measured the change in composition of gas species in the pore space at different depth levels in vertical sludge residue profiles during a resting period of 32 days. The gas composition of the pore space in the sludge residue changed during...

An assessment of off-gas treatment technologies for application to thermal treatment of Department of Energy wastes

International Nuclear Information System (INIS)

Dalton, J.D.; Gillins, R.L.; Harris, T.L.; Wollerman, A.L.

1992-09-01

The purpose of this report is to describe available air pollution control technologies for pollutants generated by thermal treatment of DOE wastes. A basic process for selecting air pollution control devices is summarized. Types of air pollutants generated by thermal treatment units are described, as well as the factors that influence the types and quantities of pollutants generated. This report also reviews applicable regulatory emission requirements. A listing of available and emerging air pollution control technologies and a brief introduction to the basic engineering principles involved in collecting each of the pollutants are presented. Section 7 of this report contains two types of evaluations for air pollution control devices. First, comparative evaluations of individual technologies are presented, based upon criteria generally relevant to DOE facilities. Using this evaluation system, the spray dryer absorber received the highest rating for acid-gas removal; high-efficiency particulate air (HEPA) filters received the highest rating for particulate removal; activated carbon adsorption received the highest rating for the removal of both toxic metals and residual hydrocarbons; and selective catalytic reduction received the highest rating for nitrogen oxide abatement. Also evaluated in Sect. 7 is the expected performance of different types of pollution control systems on two hypothetical waste streams. The waste streams were defined based upon typical DOE wastes and thermal treatment technologies. Section 8 presents conclusions for this report. Two appendixes are included with this report. The first appendix contains a brief description of all the technologies evaluated and the second lists of some of the vendors for each of the technologies that was evaluated

Proceedings of the 3. Canadian organic residuals and biosolids management conference[Manure, biosolids, and organic industrial/commercial residuals in land applications programs : improving beneficial reuse and protection of water quality

Energy Technology Data Exchange (ETDEWEB)

NONE

2007-07-01

The management of organic residuals in Canada is becoming more challenging and complex, both socially and politically. This conference provided a forum to exchange the latest information on technical legislative and public awareness issues associated with organic residuals and biosolids management in Canada. It was attended by producers, managers, practitioners and regulators from across Canada who discussed various initiatives regarding the production, management use and disposal of organic residuals including municipal wastewater treatment biosolids, animal manures and pulp and paper sludges. The sessions of the conference were entitled: biosolids management; quality issues; public perception and health issues; composting; treatment technologies; waste to energy; technology; and, land application. The conference featured 50 presentations, of which 5 have been catalogued separately for inclusion in this database. refs., tabs., figs.

A novel cryogenic treatment for reduction of residual stresses in 2024 aluminum alloy

Energy Technology Data Exchange (ETDEWEB)

Araghchi, M., E-mail: M.Araghchi@ma.iut.ac.ir [Department of Materials Engineering, Malek Ashtar University of Technology, Isfahan (Iran, Islamic Republic of); Mansouri, H.; Vafaei, R. [Department of Materials Engineering, Malek Ashtar University of Technology, Isfahan (Iran, Islamic Republic of); Guo, Yina [Bernal Institute, University of Limerick, Limerick (Ireland)

2017-03-24

Residual stresses induced during quenching of aluminum alloys cause distortion and have a negative effect on their properties. The purpose of this study is to reduce the residual stresses and improve mechanical properties by using a novel cryogenic treatment. Water quenched samples were cooled down by immersion in liquid nitrogen at −196 °C, following by rapid heating in hot oil at 180 °C and finally they were artificially aged. Residual stresses was measured by the hole drilling strain gauge method. The mechanical properties and microstructure of a heat treated samples were investigated by means of hardness measurements, tensile tests and transmission electron microscopy. The results showed that this treatment can relieve up to 71% of the residual stresses compared to 29% related to the traditional cryogenic treatment that used boiling water as the reheating medium. In addition, there is a considerable increase of about 75 MPa in the ultimate tensile strength in comparison to the T6 heat-treated alloy. TEM observations revealed that the S′ precipitates were fine and uniformly distributed in the microstructure due to deformation during reheating in hot oil.

The newest achievements of studies on the reutilization, treatment, and disposal technology of hazardous wastes

Energy Technology Data Exchange (ETDEWEB)

Liu Peizhe [Chinese Research Academy of Environmental Sciences, Beijing (China)

1996-12-31

From 1991 to 1996, key studies on the reutilization, treatment, and disposal technology of hazardous wastes have been incorporated into the national plan for environmental protection science and technology. At present, the research achievements have been accomplished, have passed national approval, and have been accepted. The author of this paper, as leader of the national group for this research work, expounds the newest achievements of the studies involving four parts: (1) the reutilization technology of electroplating sludge, including the ion-exchange process for recovering the sludge and waste liquor for producing chromium tanning agent and extracting chromium and colloidal protein from tanning waste residue; on the recovery of heavy metals from the electroplating waste liquor with microbic purification; on the demonstration project of producing modified plastics from the sludge and the waste plastics; and on the demonstration of the recovery of heavy metals from waste electroplating sludge by using the ammonia-leaching process; (2) the demonstrative research of reutilization technology of chromium waste residues, including production of self-melting ore and smelting of chromium-containing pig iron, and of pyrolytic detoxification of the residue with cyclone furnace; (3) the incineration technology of hazardous wastes with successful results of the industrial incinerator system for polychlorinated biphenyls; and (4) the safety landfill technology for disposal of hazardous wastes, with a complete set of technology for pretreatment, selection of the site, development of the antipercolating materials, and design and construction of the landfill. Only a part of the achievements is introduced in this paper, most of which has been built and is being operated for demonstration to further spreading application and accumulate experience. 6 refs., 7 figs., 6 tabs.

Prevalence and spectrum of residual symptoms in Lyme neuroborreliosis after pharmacological treatment: a systematic review.

Science.gov (United States)

Dersch, R; Sommer, H; Rauer, S; Meerpohl, J J

2016-01-01

Controversy exists about residual symptoms after pharmacological treatment of Lyme neuroborreliosis. Reports of disabling long-term sequels lead to concerns in patients and health care providers. We systematically reviewed the available evidence from studies reporting treatment of Lyme neuroborreliosis to assess the prevalence and spectrum of residual symptoms after treatment. A literature search was performed in three databases and three clinical trial registers to find eligible studies reporting on residual symptoms in patients after pharmacological treatment of LNB. Diagnosis must have been performed according to consensus-derived case definitions. No restrictions regarding study design or language were set. Symptom prevalence was pooled using a random-effects model. Forty-four eligible clinical trials and studies were found: 8 RCTs, 17 cohort studies, 2 case-control studies, and 17 case series. The follow-up period in the eligible studies ranged from 7 days to 20 years. The weighted mean proportion of residual symptoms was 28 % (95 % CI 23-34 %, n = 34 studies) for the latest reported time point. Prevalence of residual symptoms was statistically significantly higher in studies using the "possible" case definition (p = 0.0048). Cranial neuropathy, pain, paresis, cognitive disturbances, headache, and fatigue were statistically significantly lower in studies using the "probable/definite" case definition. LNB patients may experience residual symptoms after treatment with a prevalence of approximately 28 %. The prevalence and spectrum of residual symptoms differ according to the applied case definition. Symptoms like fatigue are not reported in studies using the "probable/definite" case definition. As the "possible" case definition is more unspecific, patients with other conditions may be included. Reports of debilitating fatigue and cognitive impairment after LNB, a "post-Lyme syndrome", could therefore be an artifact of unspecific case definitions in single

Stabilization of arsenic and chromium polluted soils using water treatment residues

DEFF Research Database (Denmark)

Nielsen, Sanne Skov

water and can be used as a soil amendment to decrease the mobility of CCA in contaminated soil. Stabilization with Fe-WTR was tested at the Collstrop site in Hillerød, Denmark. The site has been polluted with a wide range of wood impregnation agents including CCA during 40 years of wood impregnating...... of contaminants. Arsenic, chromium and copper cannot be degraded and existing methods for cleaning the soil are rarely used as they are expensive and technically demanding. Chemical stabilization of polluted soil is an alternative method for soil remediation, especially metal contamination, and consists in adding...... or other sorbents. Iron water treatment residues mainly consist of ferrihydrite, an oxidized iron oxy-hydroxide with a high reactivity and a large specific surface area with a high capacity for adsorption. Iron water treatment residues (Fe-WTR) are a by-product from treatment of groundwater to drinking...

Integrated nonthermal treatment system study

International Nuclear Information System (INIS)

Biagi, C.; Bahar, D.; Teheranian, B.; Vetromile, J.; Quapp, W.J.; Bechtold, T.; Brown, B.; Schwinkendorf, W.; Swartz, G.

1997-01-01

This report presents the results of a study of nonthermal treatment technologies. The study consisted of a systematic assessment of five nonthermal treatment alternatives. The treatment alternatives consist of widely varying technologies for safely destroying the hazardous organic components, reducing the volume, and preparing for final disposal of the contact-handled mixed low-level waste (MLLW) currently stored in the US Department of Energy complex. The alternatives considered were innovative nonthermal treatments for organic liquids and sludges, process residue, soil and debris. Vacuum desorption or various washing approaches are considered for treatment of soil, residue and debris. Organic destruction methods include mediated electrochemical oxidation, catalytic wet oxidation, and acid digestion. Other methods studied included stabilization technologies and mercury separation of treatment residues. This study is a companion to the integrated thermal treatment study which examined 19 alternatives for thermal treatment of MLLW waste. The quantities and physical and chemical compositions of the input waste are based on the inventory database developed by the US Department of Energy. The Integrated Nonthermal Treatment Systems (INTS) systems were evaluated using the same waste input (2,927 pounds per hour) as the Integrated Thermal Treatment Systems (ITTS). 48 refs., 68 figs., 37 tabs

Integrated nonthermal treatment system study

Energy Technology Data Exchange (ETDEWEB)

Biagi, C.; Bahar, D.; Teheranian, B.; Vetromile, J. [Morrison Knudsen Corp. (United States); Quapp, W.J. [Nuclear Metals (United States); Bechtold, T.; Brown, B.; Schwinkendorf, W. [Lockheed Martin Idaho Technologies Co., Idaho Falls, ID (United States); Swartz, G. [Swartz and Associates (United States)

1997-01-01

This report presents the results of a study of nonthermal treatment technologies. The study consisted of a systematic assessment of five nonthermal treatment alternatives. The treatment alternatives consist of widely varying technologies for safely destroying the hazardous organic components, reducing the volume, and preparing for final disposal of the contact-handled mixed low-level waste (MLLW) currently stored in the US Department of Energy complex. The alternatives considered were innovative nonthermal treatments for organic liquids and sludges, process residue, soil and debris. Vacuum desorption or various washing approaches are considered for treatment of soil, residue and debris. Organic destruction methods include mediated electrochemical oxidation, catalytic wet oxidation, and acid digestion. Other methods studied included stabilization technologies and mercury separation of treatment residues. This study is a companion to the integrated thermal treatment study which examined 19 alternatives for thermal treatment of MLLW waste. The quantities and physical and chemical compositions of the input waste are based on the inventory database developed by the US Department of Energy. The Integrated Nonthermal Treatment Systems (INTS) systems were evaluated using the same waste input (2,927 pounds per hour) as the Integrated Thermal Treatment Systems (ITTS). 48 refs., 68 figs., 37 tabs.

Bioenergy from sisal residues

Energy Technology Data Exchange (ETDEWEB)

Jungersen, G. [Dansk Teknologisk Inst. (Denmark); Kivaisi, A.; Rubindamayugi, M. [Univ. of Dar es Salaam (Tanzania, United Republic of)

1998-05-01

The main objectives of this report are: To analyse the bioenergy potential of the Tanzanian agro-industries, with special emphasis on the Sisal industry, the largest producer of agro-industrial residues in Tanzania; and to upgrade the human capacity and research potential of the Applied Microbiology Unit at the University of Dar es Salaam, in order to ensure a scientific and technological support for future operation and implementation of biogas facilities and anaerobic water treatment systems. The experimental work on sisal residues contains the following issues: Optimal reactor set-up and performance; Pre-treatment methods for treatment of fibre fraction in order to increase the methane yield; Evaluation of the requirement for nutrient addition; Evaluation of the potential for bioethanol production from sisal bulbs. The processing of sisal leaves into dry fibres (decortication) has traditionally been done by the wet processing method, which consumes considerable quantities of water and produces large quantities of waste water. The Tanzania Sisal Authority (TSA) is now developing a dry decortication method, which consumes less water and produces a waste product with 12-15% TS, which is feasible for treatment in CSTR systems (Continously Stirred Tank Reactors). (EG)

Residual water treatment for gamma radiation. Tratamiento de aguas residuales por radiacion gamma

Energy Technology Data Exchange (ETDEWEB)

Mendez, L [Universidad Nacional Mayor de San Marcos. Facultad de Quimica (Peru)

1990-07-01

The treatment of residual water by means of gamma radiation for its use in agricultural irrigation is evaluated. Measurements of physical, chemical, biological and microbiological contamination indicators were performed. For that, samples from the treatment center of residual water of San Juan de Miraflores were irradiated up to a 52.5 kGy dose. The study concludes that gamma radiation is effective to remove parasites and bacteria, but not for removal of the organic and inorganic matter. (author). 15 refs., 3 tabs., 4 figs.

Viimsi water treatment plant for Ra removal: NORM residue/waste generation, radiation safety issues, and regulatory response

Energy Technology Data Exchange (ETDEWEB)

Kiisk, M.; Suursoo, S.; Realo, E.; Jantsikene, A.; Lumiste, L.; Vaeaer, K.; Isakar, K.; Koch, R. [University of Tartu (Estonia)

2014-07-01

In early 2012, the first large-scale water treatment plant, specifically designed to remove Ra-isotopes from groundwater, was commissioned in Viimsi parish, North-Estonia. The plant serves approximately 15 000 consumers with maximum production capacity of 6000 m{sup 3}/d. The chosen water treatment technology is chemical free and is based on co-precipitation and adsorption with Fe(OH){sub 3} and MnO{sub 2} flocks, and adsorption of residual Ra onto zeolite sand. The chosen technology is a complex approach and is designed to reduce high Fe and Mn concentrations as well as dissolved gases along with Ra isotopes. It is proved to be well adapted with hydro-chemical conditions of the groundwater feeding the plant. As the novel technology has been applied for the first time on a large scale, the plant was taken under long-term investigation when commissioned. The latter focuses on three areas: Ra removal efficiency and its dynamics, build-up of radioactive waste, and radiation safety. The average Ra-226 and Ra-228 activity concentrations in raw water feeding the plant are approximately 0.5 Bq/L and 0.6 Bq/L, respectively, resulting in total indicative dose of 0.4 mSv/y. Operating conditions of the plant are restricted by the established indicative value of 0.1 mSv/y for drinking water, i.e. a minimum 75% removal efficiency for Ra is required. Results of the studies show that the plant operates at Ra-removal efficiency of 98% or higher without the need of regeneration or replacement of filtering materials within the first two years. Measurements confirm that ∼90% of Ra accumulates in the solid filter media, 8-9% is washed out by backwash system as liquid effluent and 1-2% is fed on to the consumer distribution network. It has been calculated that at the level of current production capacity (below 3000 m{sup 3}/d) the yearly accumulation rate in the plant is approximately 300 and 400 MBq/y for Ra-226 and Ra-228, respectively. These values strongly exceed the exemption

Efficiency of Livestock Residue Treatment in Geomembrane Digesters

Directory of Open Access Journals (Sweden)

Yanet Pérez González

2017-09-01

Full Text Available The efficiency of twelve 10 m3 geomembrane biodigesters to treat swine and cattle residuals was assessed. The study took place at the Cooperative of Credits and Services (CCS of the municipality of Cumanayagua, Cienfuegos, Cuba. Its goal was to evaluate feasibility of technology implementation in Cuba. The effluent physical and chemical indicators were determined at entry and exit from biodigesters. The biodigesters charged with pig manure were able to remove 75.88% COD, and up to 66-44% SS. Besides, 64.79% of the contaminating organic load was converted into volatile products during biofermentation. Meanwhile, the biodigesters charged with cattle manure removed 60.42% of COD, and up to 67.67% of SS; 61.51% of the organic contaminating load was converted in volatile products. It was concluded that the biodigesters had acceptable efficiency values, and that the technology can be applied in Cuba.

The importance of antibiotic residues presence detection in milk

Directory of Open Access Journals (Sweden)

Dubravka Samaržija

2002-01-01

Full Text Available Antibiotic residues are the most present inhibitory substances in milkhaving undesirable effect on human health, technological characteristics and the quality of milk and dairy products. In order to protect consumer's health and to ensure high quality milk production, European Union (EU regulation 2377/90 sets a maximum permitted levels for antibiotic residues in milk. Although the presence of antibiotic residues in milk can be due to animal diseases treatment, and in the case of milking animals, they are mostly present after mastitis treatment. The aim of this work is to stress the importance of the continuous control on antibiotic residues presence in milk, due to the role that milk and dairy products have in human nutrition. In this paper, different groups of antibiotics, mechanisms of theirs action, mistakes occurring in dairy products manufacture as well as the methods for theirs detection are described.

Evaluation of Membrane Ultrafiltration and Residual Chlorination as a Decentralized Water Treatment Strategy for Ten Rural Healthcare Facilities in Rwanda

Directory of Open Access Journals (Sweden)

Alexandra Huttinger

2015-10-01

Full Text Available There is a critical need for safe water in healthcare facilities (HCF in low-income countries. HCF rely on water supplies that may require additional on-site treatment, and need sustainable technologies that can deliver sufficient quantities of water. Water treatment systems (WTS that utilize ultrafiltration membranes for water treatment can be a useful technology in low-income countries, but studies have not systematically examined the feasibility of this technology in low-income settings. We monitored 22 months of operation of 10 WTS, including pre-filtration, membrane ultrafiltration, and chlorine residual disinfection that were donated to and operated by rural HCF in Rwanda. The systems were fully operational for 74% of the observation period. The most frequent reasons for interruption were water shortage (8% and failure of the chlorination mechanism (7%. When systems were operational, 98% of water samples collected from the HCF taps met World Health Organization (WHO guidelines for microbiological water quality. Water quality deteriorated during treatment interruptions and when water was stored in containers. Sustained performance of the systems depended primarily on organizational factors: the ability of the HCF technician to perform routine servicing and repairs, and environmental factors: water and power availability and procurement of materials, including chlorine and replacement parts in Rwanda.

Treatment of waste incinerator air-pollution-control residues with FeSO4: Concept and product characterization

DEFF Research Database (Denmark)

Lundtorp, Kasper; Jensen, Dorthe Lærke; Sørensen, Mette Abildgaard

2002-01-01

This paper describes a new concept for treatment of air- pollution-control (APC) residues from waste incineration and characterises the wastewater and stabilised residues generated by the process. The process involves mixing of APC-residues with a ferrous sulphate solution and subsequent oxidation...

Gas composition of sludge residue profiles in a sludge treatment reed bed between loadings.

Science.gov (United States)

Larsen, Julie D; Nielsen, Steen M; Scheutz, Charlotte

2017-11-01

Treatment of sludge in sludge treatment reed bed systems includes dewatering and mineralization. The mineralization process, which is driven by microorganisms, produces different gas species as by-products. The pore space composition of the gas species provides useful information on the biological processes occurring in the sludge residue. In this study, we measured the change in composition of gas species in the pore space at different depth levels in vertical sludge residue profiles during a resting period of 32 days. The gas composition of the pore space in the sludge residue changed during the resting period. As the resting period proceeded, atmospheric air re-entered the pore space at all depth levels. The methane (CH 4 ) concentration was at its highest during the first part of the resting period, and then declined as the sludge residue became more dewatered and thereby aerated. In the pore space, the concentration of CH 4 often exceeded the concentration of carbon dioxide (CO 2 ). However, the total emission of CO 2 from the surface of the sludge residue exceeded the total emission of CH 4 , suggesting that CO 2 was mainly produced in the layer of newly applied sludge and/or that CO 2 was emitted from the sludge residue more readily compared to CH 4 .

Valorisation of food residues: waste to wealth using green chemical technologies

OpenAIRE

Clark, James H.; Luque, Rafael

2013-01-01

Waste valorisation practises have attracted a significant amount of attention in recent years with the aim of managing waste in the most sustainable way. Food waste constitutes a largely under-exploited residue from which a variety of valuable chemicals can be derived. This contribution is aimed to set the scene for a further development and promotion of sustainable food waste valorisation practises to different end products using green chemical technologies

Power generation with technology innovation of residual biomass utilization; Geracao de energia com inovacao tecnologica de aproveitamento de biomassa residual

Energy Technology Data Exchange (ETDEWEB)

Moura, Johnson Pontes de; Selvam, P.V. Pannir [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil)

2006-07-01

In the present work, the introduction of alternative energy of biogas in agricultural communities for the sustainable development was studied through exploitation of residual biomass and also getting as by-product the biological fertilizer. A fast composting of the domestic residue with the organic was made possible where part of this residue after processing was taken together with effluent to the biodigester. The bibliographical research on the processes of generation of biogas, about composting and the equipment for processing had been carried through. The projects engineering with the use of computational tools had been developed with the software Super Pro 4,9 Design and ORC GPEC 2004 by our research group. Five case studies had been elaborated, where different scenes related with our innovation, that uses of the residue for the composting together with domestic effluent for digestion. Several economic parameters were obtained and our work proved the viability about the use of biogas for drying of the fruits banana. A economic feasibility study was carried where it was proven that the project with the innovation of the use of residues from the fruits possess more advantages than the conventional system of drying using electric energy. Considering the viability of this process and the use solar energy, it is intended to apply this technology in rural agricultural communities providing them an energy source of low cost in substitution of the conventional energy. (author)

Techniques of material-flow-specific residual waste treatment; Techniken der stoffstromspezifischen Restabfallbehandlung

Energy Technology Data Exchange (ETDEWEB)

Maak, D.; Collins, H.J. [Technische Univ. Braunschweig, Leichtweiss - Inst. fuer Wasserbau (Germany)

1998-09-01

The success achieved with large-scale plants for mechanical-biological residual waste treatment has led to a change of course in waste pretreatment. In view of the low emissions via the water and gas routes from landfilled wastes and the low costs of waste treatment some authorising authorities have meanwhile issued special licences pursuant to clause no. 2.4 of the Technical Code on Household Waste, thus enabling mechanical-biological residual waste treatment plants to continue operations beyond the year 2005. Beside offering a means of treatment and disposal, cost-effective mechanical-biological pretreatment also provides an opportunity for going over to material-flow-specific residual waste treatment. These process stages permit recirculating valuable materials and using other materials for energy production. They can be retrofitted on a modular basis in existing plants. If these advantages of the present innovative pretreatment methods are not used, then mechanical-biological pretreatment can still serve as a preparatory stage for thermal treatment. To date there has been no practical experience with this innovative method of residual waste treatment. However, industrial-scale trials have shown that each individual treatment stage is capable of being carried out successfully. [Deutsch] Die guten Erfolge im grosstechnischen Betrieb von Anlagen zur mechanisch-biologischen Restabfallbehandlung haben zu einer Kursaenderung bei der Vorbehandlung von Abfaellen gefuehrt. Geringe Emissionen der deponierten Abfaelle auf dem Gas- und Wasserpfad sowie geringe Kosten fuer die Behandlung der Abfaelle haben dazu gefuehrt, dass inzwischen bereits einige Genehmigungsbehoerden eine Ausnahmegenehmigung nach Nr. 2.4 der TA Siedlungsabfall erteilt haben und damit der Betrieb von mechanisch-biologischen Restabfallbehandlungsanlagen auch nach 2005 ermoeglicht wird. Neben der alleinigen Behandlung und Deponierung bietet die kostenguenstige Vorbehandlung mit mechanisch

Residual bovine serum albumin (BSA) quantitation in vaccines using automated Capillary Western technology.

Science.gov (United States)

Loughney, John W; Lancaster, Catherine; Ha, Sha; Rustandi, Richard R

2014-09-15

Bovine serum albumin (BSA) is a major component of fetal bovine serum (FBS), which is commonly used as a culture medium during vaccine production. Because BSA can cause allergic reactions in humans the World Health Organization (WHO) has set a guidance of 50 ng or less residual BSA per vaccine dose. Vaccine manufacturers are expected to develop sensitive assays to detect residual BSA. Generally, sandwich enzyme-linked immunosorbent assays (ELISA) are used in the industry to detect these low levels of BSA. We report the development of a new improved method for residual BSA detection using the SimpleWestern technology to analyze residual BSA in an attenuated virus vaccine. The method is based on automated Capillary Western and has linearity of two logs, >80% spike recovery (accuracy), intermediate precision of CV <15%, and LOQ of 5.2 ng/ml. The final method was applied to analyze BSA in four lots of bulk vaccine products and was used to monitor BSA clearance during vaccine process purification. Copyright © 2014 Elsevier Inc. All rights reserved.

Fuel gas production from animal and agricultural residues and biomass

Energy Technology Data Exchange (ETDEWEB)

Wise, D. L; Wentworth, R. L

1978-05-30

Progress was reported by all contractors. Topics presented include: solid waste to methane gas; pipeline fuel gas from an environmental cattle feed lot; heat treatment of organics for increasing anaerobic biodegradability; promoting faster anaerobic digestion; permselective membrane control of algae and wood digesters for increased production and chemicals recovery; anaerobic fermentation of agricultural residues; pilot plant demonstration of an anaerobic, fixed-film bioreactor for wastewater treatment; enhancement of methane production in the anaerobic diegestion of sewage; evaluation of agitation concepts for biogasification of sewage sludge; operation of a 50,000 gallon anaerobic digester; biological conversion of biomass to methane; dirt feedlot residue experiments; anaerobic fermentation of livestock and crop residues; current research on methanogenesis in Europe; and summary of EPA programs in digestion technology. (DC)

Waste Treatment of Chrome Residue of Chromium Recovery Process Using Calcium Carbonate

International Nuclear Information System (INIS)

Endro Kismolo; Prayitno; Nurimaniwathy

2002-01-01

The aim of the research was to apply the precipitation technology for the treatment of aqueous wastes of leather tanning industries. The chrome liquid wastes taken was the effluent from the residue of the chromium recovery process using magnesium oxide. The precipitant used was calcium carbonate. The experiments was performed by adjusting the concentration of calcium carbonate from 50 ppm, 100 ppm, 150 ppm, 200 ppm, 250 ppm, 300 ppm, 350 ppm to 400 ppm. The stirring speed was varied from 50 rpm, 75 rpm, 100 rpm, 125 rpm, 150 rpm, 175 rpm to 200 rpm. The time of mixing was varied from 30 minutes, 60 minutes, 90 minutes, 120 minutes, 150 minutes, 175 minutes and 200 minutes. The result from the experiments lead to the best condition obtained were the concentration of precipitant was 300 ppm, flow rates of mixing was 125 rpm and time of mixing was 60 minutes. At this condition the separations efficiency of chrome obtained was 99.985%. (author)

Investigation of patient, tumour and treatment variables affecting residual motion for respiratory-gated radiotherapy

International Nuclear Information System (INIS)

George, R; Ramakrishnan, V; Siebers, J V; Chung, T D; Keall, P J

2006-01-01

Respiratory gating can reduce the apparent respiratory motion during imaging and treatment; however, residual motion within the gating window remains. Respiratory training can improve respiratory reproducibility and, therefore, the efficacy of respiratory-gated radiotherapy. This study was conducted to determine whether residual motion during respiratory gating is affected by patient, tumour or treatment characteristics. The specific aims of this study were to: (1) identify significant characteristics affecting residual motion, (2) investigate time trends of residual motion over a period of days (inter-session) and (3) investigate time trends of residual motion within the same day (intra-session). Twenty-four lung cancer patients were enrolled in an Institutional Review Board (IRB)-approved protocol. For approximately five sessions, 331 four-minute, respiratory motion traces were acquired with free breathing, audio instructions and audio-visual biofeedback for each patient. The residual motion was quantified by the standard deviation of the displacement within the gating window. The generalized linear model was used to obtain coefficients for each variable within the model and to evaluate the clinical and statistical significance. The statistical significance was determined by a p-value <0.05, while effect sizes of ≥0.1 cm (one standard deviation) were considered clinically significant. This data analysis was applied to patient, tumour and treatment variables. Inter- and intra-session variations were also investigated. The only variable that was significant for both inhale- and exhale-based gating was disease type. In addition, visual-training displacement, breathing type and Karnofsky performance status (KPS) values were significant for inhale-based gating, and dose-per-fraction was significant for exhale-based gating. Temporal respiratory variations within and between sessions were observed for individual patients. However inter- and intra-session analyses did

Investigation of patient, tumour and treatment variables affecting residual motion for respiratory-gated radiotherapy

Energy Technology Data Exchange (ETDEWEB)

George, R [Department of Radiation Oncology, Virginia Commonwealth University, Richmond, VA (United States); Ramakrishnan, V [Department of Biostatistics, Virginia Commonwealth University, Richmond, VA (United States); Siebers, J V [Department of Radiation Oncology, Virginia Commonwealth University, Richmond, VA (United States); Chung, T D [Department of Radiation Oncology, Virginia Commonwealth University, Richmond, VA (United States); Keall, P J [Department of Radiation Oncology, Virginia Commonwealth University, Richmond, VA (United States)

2006-10-21

Respiratory gating can reduce the apparent respiratory motion during imaging and treatment; however, residual motion within the gating window remains. Respiratory training can improve respiratory reproducibility and, therefore, the efficacy of respiratory-gated radiotherapy. This study was conducted to determine whether residual motion during respiratory gating is affected by patient, tumour or treatment characteristics. The specific aims of this study were to: (1) identify significant characteristics affecting residual motion, (2) investigate time trends of residual motion over a period of days (inter-session) and (3) investigate time trends of residual motion within the same day (intra-session). Twenty-four lung cancer patients were enrolled in an Institutional Review Board (IRB)-approved protocol. For approximately five sessions, 331 four-minute, respiratory motion traces were acquired with free breathing, audio instructions and audio-visual biofeedback for each patient. The residual motion was quantified by the standard deviation of the displacement within the gating window. The generalized linear model was used to obtain coefficients for each variable within the model and to evaluate the clinical and statistical significance. The statistical significance was determined by a p-value <0.05, while effect sizes of {>=}0.1 cm (one standard deviation) were considered clinically significant. This data analysis was applied to patient, tumour and treatment variables. Inter- and intra-session variations were also investigated. The only variable that was significant for both inhale- and exhale-based gating was disease type. In addition, visual-training displacement, breathing type and Karnofsky performance status (KPS) values were significant for inhale-based gating, and dose-per-fraction was significant for exhale-based gating. Temporal respiratory variations within and between sessions were observed for individual patients. However inter- and intra-session analyses did

Some techniques used in the treatment of phenolic waters residual

International Nuclear Information System (INIS)

Alzate S, Rafael A.; Botero, Carlos Andre

2000-01-01

The current state of the diverse processes of treatment of phenolic waters residual is presented, beginning with the methods traditionally employees, until finishing with those but recent innovations, which have been derived of the necessity of increasing the removal of these pollutants without increasing the costs of such processes in excessive form

The characterization of insoluble dissolver residues and the development of treatment methods

International Nuclear Information System (INIS)

Baker, H.T.; Brown, P.E.; Pateman, R.J.; Wilkinson, K.L.

1986-01-01

Characterization studies have been carried out on the insoluble residue arising from laboratory scale dissolution of single pins of mixed oxide fuel irradiated in the Dounreay Fast Reactor (DFR). Similar characterization work has also been completed on six samples of insoluble residue recovered from the reprocessing of complete sub-assemblies of mixed oxide fuel irradiated in PFR. Treatment methods for the dissolver insolubles have consisted of preparing immobilized samples in sand/ordinary portland cement (OPC), sand/pulverized fly ash (PFA)/OPC, and blast furnace slag (BFS)/OPC. A programme of leach testing has been carried out according to the conditions laid down in the international Standard Organization Test. Four samples of DFR originated insoluble residues and six samples of PFR originated insoluble residues have been immobilized and leach tested. Variations have included experiments to evaluate the leach rate under temperature influence and to acid wash prior to immobilization

Use of Interface Treatment to Reduce Emissions from Residuals in Lower Permeability Zones to Groundwater flowing Through More Permeable Zones (Invited)

Science.gov (United States)

Johnson, P.; Cavanagh, B.; Clifton, L.; Daniels, E.; Dahlen, P.

2013-12-01

Many soil and groundwater remediation technologies rely on fluid flow for contaminant extraction or reactant delivery (e.g., soil vapor extraction, pump and treat, in situ chemical oxidation, air sparging, enhanced bioremediation). Given that most unconsolidated and consolidated settings have permeability contrasts, the outcome is often preferential treatment of more permeable zones and ineffective treatment of the lower permeability zones. When this happens, post-treatment contaminant emissions from low permeability zone residuals can cause unacceptable long-term impacts to groundwater in the transmissive zones. As complete remediation of the impacted lower permeability zones may not be practicable with conventional technologies, one might explore options that lead to reduction of the contaminant emissions to acceptable levels, rather than full remediation of the lower permeability layers. This could be accomplished either by creating a sustained emission reaction/attenuation zone at the high-low permeability interface, or by creating a clean soil zone extending sufficiently far into the lower permeability layer to cause the necessary reduction in contaminant concentration gradient and diffusive emission. These options are explored in proof-of-concept laboratory-scale physical model experiments. The physical models are prepared with two layers of contrasting permeability and either dissolved matrix storage or nonaqueous phase liquid (NAPL) in the lower permeability layer. A dissolved oxidant is then delivered to the interface via flow across the higher permeability layer and changes in contaminant emissions from the low permeability zone are monitored before, during, and after oxidant delivery. The use of three oxidants (dissolved oxygen, hydrogen peroxide and sodium persulfate) for treatment of emissions from petroleum hydrocarbon residuals is examined.

Treatment methods and comparative risks of thorium removal from waste residues

International Nuclear Information System (INIS)

Porter, R.D.; Hamby, D.M.; Martin, J.E.

1997-07-01

This study was done to examine the risks of remediation and the effectiveness of removal methods for thorium and its associated radioactive decay products from various soils and wastes associated with DOE's Formerly Utilized Sites Remedial Action Program (FUSRAP). Removal of 230 Th from uranium process residues would significantly reduce the buildup of 226 Ra (half-life of 1600 years), and since 230 Th concentrations at most of the important sites greatly exceed the 226 Ra concentrations, such removal would reduce the accumulation of additional radiation risks associated with 226 Ra and its products; and, if treatment also removed 226 Ra, these risks could be mitigated even further. Removal of 232 Th from thorium process residues would remove the source material for 228 Ra, and since 228 Ra has a half-life of 5.76 years, its control at FUSRAP sites could be done with land use controls for the 30--50 years required for 228 Ra and the risks associated with its decay products to decay away. It must be recognized, however, that treatment methods invariably require workers to process residues and waste materials usually with bulk handling techniques. These processes expose workers to the radioactivity in the materials, therefore, workers would incur radiological risks in addition to industrial accident risks. An important question is whether the potential reduction of future radiological risks to members of the public justifies the risks that are incurred by remediation workers due to handling materials. This study examines, first, the effectiveness of treatment and then the risks that would be associated with remediation

Proceedings of the 7. biennial residue-to-revenue residual wood conference 2007

International Nuclear Information System (INIS)

Raulin, J.

2007-01-01

This conference provided information on the highest and best use of residual wood, which is quickly becoming a valuable commodity. Issues concerning forest residues, sawmill wastes, agricultural residues and urban organic materials were discussed along with trends in Canadian surplus mill waste production. The evolving nature and technologies of the biomass business were highlighted with particular focus on how to generate energy and save money through the use of residual wood. Residual wood energy projects and developments in Canada, North America and Europe were outlined along with biomass development in relation to forest fires and insect disturbances. Cogeneration technologies using wood wastes for thermal heat, steam and electricity were also presented, along with transportation fuel technologies for the production of ethanol. It was noted that with the rising cost of energy, the forest industry is seeking energy solutions based on the use of residual wood. The range of economically practical residual wood solutions continues to grow as energy prices increase. The conference was attended by more than 200 delegates from the forest industry, suppliers and government representatives, to discuss policies and procedures currently in place. Industry investment is being stimulated by the potential for biofuels and biochemicals, as well as the co-operation between the forest and energy sectors. The conference featured 23 presentations, of which 12 have been catalogued separately for inclusion in this database. refs., tabs., figs

Analysis of residual stress relief mechanisms in post-weld heat treatment

International Nuclear Information System (INIS)

Dong, Pingsha; Song, Shaopin; Zhang, Jinmiao

2014-01-01

This paper presents a recent study on weld residual stress relief mechanisms associated with furnace-based uniform post-weld heat treatment (PWHT). Both finite element and analytical methods are used to quantitatively examine how plastic deformation and creep relaxation contribute to residual stress relief process at different stages of PWHT process. The key contribution of this work to an improved understanding of furnace based uniform PWHT can be summarized as follows: (1)Plastic deformation induced stress relief during PWHT can be analytically expressed by the change in material elastic deformation capacity (or elastic deformation limit) measured in terms of material yield strength to Young's modulus ratio, which has a rather limited role in overall residual stress relief during furnace based uniform PWHT. (2)The most dominant stress relief mechanism is creep strain induced stress relaxation, as expected. However, a rapid creep strain development accompanied by a rapid residual stress reduction during heating stage before reaching PWHT temperature is shown to contribute to most of the stress relief seen in overall PWHT process, suggesting PWHT hold time can be significantly reduced as far as residual stress relief is concerned. (3)A simple engineering scheme for estimating residual stress reduction is proposed based on this study by relating material type, PWHT temperature, and component wall thickness. - Highlights: • The paper clarified effects of plastic deformation and creep relaxation on weld residual stress relief during uniform PWHT. • Creep strain development is far more important than plastic strain, mostly completed even before hold time starts. • Plastic strain development is insignificant and be analytically described by a material elastic deformation capacity parameter. • An engineering estimation scheme is proposed for determining residual stress reduction resulted from furnace based PWHT

DOE's Innovative Treatment Remediation Demonstration Program accelerating the implementation of innovative technologies

International Nuclear Information System (INIS)

Hightower, M.

1995-01-01

A program to help accelerate the adoption and implementation of new and innovative remediation technologies has been initiated by the Department of Energy's (DOE) Environmental Restoration Program Office (EM40). Developed as a Public-Private Partnership program in cooperation with the US Environmental Protection Agency's (EPA) Technology Innovation Office (TIO) and coordinated by Sandia National Laboratories, the Innovative Treatment Remediation Demonstration (ITRD) Program attempts to reduce many of the classic barriers to the use of new technologies by involving government, industry, and regulatory agencies in the assessment, implementation, and validation of innovative technologies. In this program, DOE facilities work cooperatively with EPA, industry, national laboratories, and state and federal regulatory agencies to establish remediation demonstrations using applicable innovative technologies at their sites. Selected innovative technologies are used to remediate small, one to two acre, sites to generate the full-scale and real-world operating, treatment performance, and cost data needed to validate these technologies and gain acceptance by industry and regulatory agencies, thus accelerating their use nationwide. Each ITRD project developed at a DOE site is designed to address a typical soil or groundwater contamination issue facing both DOE and industry. This includes sites with volatile organic compound (VOC), semi-VOC, heavy metal, explosive residue, and complex or multiple constituent contamination. Projects are presently underway at three DOE facilities, while additional projects are under consideration for initiation in FY96 at several additional DOE sites. A brief overview of the ITRD Program, program plans, and the status and progress of existing ITRD projects are reviewed in this paper

Controlling Bacterial Pathogens in Water for Reuse: Treatment Technologies for Water Recirculation in the Blue Diversion Autarky Toilet

Directory of Open Access Journals (Sweden)

Mi T. Nguyen

2017-12-01

Full Text Available HighlightBacterial growth in fecally-contaminated water is highly variable and dependent on several factors.Regrowth occurs after chlorination (low doses, no residual.Indigenous microbial communities variably impact bacterial growth.A combination of treatments can both inactivate and inhibit growth.The Blue Diversion AUTARKY Toilet is a urine-diverting toilet with on-site treatment. The toilet is being developed to provide a safe and affordable sanitation technology for people who lack access to sewer-based sanitation. Water used for personal hygiene, hand washing, and flushing to rinse urine- and feces-collection bowls is treated, stored, and recycled for reuse to reduce reliance on external water supplies. The system provides an opportunity to investigate hygiene of water for reuse following treatment. Treatment in the toilet includes a Biologically Activated Membrane Bioreactor (BAMBi followed by a secondary treatment technology. To identify effective secondary treatment, three options, including granular activated carbon (GAC only, GAC+chlorine (sodium hypochlorite, and GAC+electrolysis are considered based on the bacterial inactivation and growth inhibition efficiency. Four different hygiene-relevant bacteria are tested: Escherichia coli, Enterococcus faecalis, Pseudomonas aeruginosa, and Salmonella typhimurium. Our evaluation demonstrates that—despite treatment of water with the BAMBi—E. coli, P. aeruginosa, and S. typhimurium have the potential to grow during storage in the absence of microbial competition. Including the indigenous microbial community influences bacterial growth in different ways: E. coli growth decreases but P. aeruginosa growth increases relative to no competition. The addition of the secondary treatment options considerably improves water quality. A column of GAC after the BAMBi reduces E. coli growth potential by 2 log10, likely due to the reduction of carbon sources. Additional treatments including chlorination

A process for treatment of residues from dry/semidry APC systems at municipal solid waste incinerators. Final report

Energy Technology Data Exchange (ETDEWEB)

Hjelmar, O. [VKI, Hoersholm (Denmark)] Holland, D. [FLS miljoe a/s, Valby (Denmark)] Poulsen, B. [KARA, Roskilde (Denmark)

1997-08-01

The main objective of the project has been to establish and test a process for treatment of residues from the semidry (and dry) lime injection based APC processes at MSWIs, which will ensure that the residues can be managed in an environmentally safe manner. In pursuit of this goal, the following activities have been carried out: Performance of pilot scale extractions (approximately 50 kg of residue per batch) at the KARA MSWI in Roskilde of semidry APC system residues in order to establish and optimize process conditions. The optimization includes consideration of the possibilities for subsequent treatment/stabilization of the extracted solid phase as well as the possibility of treatment and safe discharge/utilization of the extract; Performance of chemical characterization, hydrogeochemical model calculations and experimental work in order to improve the understanding of the mechanisms and factors which for several contaminants control the equilibrium between the solid and liquid phases, both in the short and the long germ, and to use this information to obtain an environmentally acceptable method for stabilization/treatment of the extracted residues while at the same time minimizing the necessary amount of additives; production of treated residues and performance of leaching tests on these to assess and demonstrate the effectiveness of the entire process (extraction + stabilization/treatment); Evaluation of the technical, economical and environmental consequences of full scale implementation of the process. (EG) EFP-94. 19 refs.

Recycling of air pollution control residues from municipal solid waste incineration into lightweight aggregates.

Science.gov (United States)

Quina, Margarida J; Bordado, João M; Quinta-Ferreira, Rosa M

2014-02-01

This work focuses on the assessment of technological properties and on the leaching behavior of lightweight aggregates (LWA) produced by incorporating different quantities of air pollution control (APC) residues from municipal solid waste (MSW) incineration. Currently this hazardous waste has been mostly landfilled after stabilization/solidification. The LWA were produced by pelletizing natural clay, APC residues as-received from incineration plant, or after a washing treatment, a small amount of oil and water. The pellets were fired in a laboratory chamber furnace over calcium carbonate. The main technological properties of the LWA were evaluated, mainly concerning morphology, bulk and particle densities, compressive strength, bloating index, water adsorption and porosity. Given that APC residues do not own expansive (bloating) properties, the incorporation into LWA is only possible in moderate quantities, such as 3% as received or 5% after pre-washing treatment. The leaching behavior of heavy metals from sintered LWA using water or acid solutions was investigated, and despite the low acid neutralization capacity of the synthetic aggregates, the released quantities were low over a wide pH range. In conclusion, after a washing pre-treatment and if the percentage of incorporation is low, these residues may be incorporated into LWA. However, the recycling of APC residues from MSW incineration into LWA does not revealed any technical advantage. Copyright © 2013 Elsevier Ltd. All rights reserved.

Effects of Adopting Different Kinds of Collecting Method for Years on Film Residual Coefficient and Maize Yields

Directory of Open Access Journals (Sweden)

TANG Wen-xue

2017-03-01

Full Text Available Wide usage of mulching technology has increased crop yields, but the large amounts of mulching film residue resulting from widespread use of plastic film in China has brought about a series of pollution hazards. Based on a 4-year (2011-2014 long-term experiment, the effects of different kinds of collecting mothod (zero plastic film residues, conventional plastic film residues, whole plastic film residues remainded on plastic film residues, residual coefficient and maize yield were explored. Plastic film residues mainly remained in 0~10 cm, 10~20 cm soil layers. In 0~30 cm soil layers, the two types of mulch residues (>25 cm2, 4~25 cm2 under zero plastic film residues treatment were much less than conventional plastic film residues and whole plastic film residues remainded treatments, no significant differences were observed in the mulch residues (2 among 3 treatments. After maize harvest, the amount of plastic film residues under zero plastic film residues, conventional plastic film residues and whole plastic film residues remainded treatments were 52.71, 80.85 kg·hm-2 and 152.65 kg·hm-2, respectively, the residual coefficient for zero plastic film residues, conventional plastic film residues and whole plastic film residues remainded treatments were -9.45%, 8.53% and 54.42%, respectively. The stem diameter, ear length, ear width, ear row number, grain number per row and 100-grain weight of maize decreased with the increase of residual film amount. Compared with the conventional plastic film residues, the mean grain yield of whole plastic film residues remainded treatment decreased by 15.08%, whereas the zero plastic film residues treatment increased by 4.70%. The plastic film residues, residual coefficient and maize yield were comprehensively analyzed, the conventional plastic film residues practice should be adopted currently without appropriate plastic film residues collector. But from the long-term development, we should speed up the

Guide to treatment technology for contaminated soils

International Nuclear Information System (INIS)

Tran, H.; Aylward, R.

1992-01-01

This document is a guide for the screening of alternative treatment technologies for contaminated soils. The contents of this guide are organized into: 1. Introduction, II. Utilizing the table, III. Tables: Contamination Versus Technology, TV. Contaminant Waste Groups, and V. References. The four Contaminations Versus Technology tables are designed to identify the effectiveness and/or potential applicability of technologies to some or all compounds within specific waste groups. The tables also present limitations and special use considerations for the particular treatment technology. The phase of development of the technology is also included in the table. The phases are: Available, Innovative, and Emerging technologies. The technologies presented in this guide are organized according to the method of treatment. The four (4) treatment methods are Biological, Solidification/Stabilization, Thermal, and Chemical/Physical Treatment. There are several processing methods; some are well developed and proven, and others are in the development stage

Treatment methods and comparative risks of thorium removal from waste residues

Energy Technology Data Exchange (ETDEWEB)

Porter, R.D.; Hamby, D.M.; Martin, J.E.

1997-07-01

This study was done to examine the risks of remediation and the effectiveness of removal methods for thorium and its associated radioactive decay products from various soils and wastes associated with DOE`s Formerly Utilized Sites Remedial Action Program (FUSRAP). Removal of {sup 230}Th from uranium process residues would significantly reduce the buildup of {sup 226}Ra (half-life of 1600 years), and since {sup 230}Th concentrations at most of the important sites greatly exceed the {sup 226}Ra concentrations, such removal would reduce the accumulation of additional radiation risks associated with {sup 226}Ra and its products; and, if treatment also removed {sup 226}Ra, these risks could be mitigated even further. Removal of {sup 232}Th from thorium process residues would remove the source material for {sup 228}Ra, and since {sup 228}Ra has a half-life of 5.76 years, its control at FUSRAP sites could be done with land use controls for the 30--50 years required for {sup 228}Ra and the risks associated with its decay products to decay away. It must be recognized, however, that treatment methods invariably require workers to process residues and waste materials usually with bulk handling techniques. These processes expose workers to the radioactivity in the materials, therefore, workers would incur radiological risks in addition to industrial accident risks. An important question is whether the potential reduction of future radiological risks to members of the public justifies the risks that are incurred by remediation workers due to handling materials. This study examines, first, the effectiveness of treatment and then the risks that would be associated with remediation.

Treatment of Lignin and Waste residues by Flash Pyrolysis

DEFF Research Database (Denmark)

Jensen, Peter Arendt; Trinh, Ngoc Trung; Dam-Johansen, Kim

pyrolysis properties were compared with the pyrolysis properti es of wood and straw. The PCR treatment of sewage sludge provides an oil that can be used for energy pur poses and a solid residue rich in in organic nutrients that may be used as fertilizer product. By fast pyroly sis of lignin from the IBUS...... be operated at low rotational speed was constructed. The new rotor systems should make it easier to make an up-scaling of the process....

Residual stress and mechanical properties of SiC ceramic by heat treatment

International Nuclear Information System (INIS)

Yoon, H.K.; Kim, D.H.; Shin, B.C.

2007-01-01

Full text of publication follows: Silicon carbide is a compound of relatively low density, high hardness, elevated thermal stability and good thermal conductivity, resulting in good thermal shock resistance. Because of these properties, SiC materials are widely used as abrasives and refractories. In this study, SiC single and poly crystals was grown by the sublimation method using the SiC seed crystal and SiC powder as the source material. Mechanical properties of SiC single and poly crystals are carried out by using the nano-indentation method and small punch test after the heat treatment. As a result, mechanical properties of SiC poly crystal had over double than single. And SiC single and poly crystals were occurred residual stress, but residual stress was shown relaxant properties by the effect of heat treatment. (authors)

X-ray absorption spectroscopy as a tool investigating arsenic(III) and arsenic(V) sorption by an aluminum-based drinking-water treatment residual.

Science.gov (United States)

Makris, Konstantinos C; Sarkar, Dibyendu; Parsons, Jason G; Datta, Rupali; Gardea-Torresdey, Jorge L

2009-11-15

Historic applications of arsenical pesticides to agricultural land have resulted in accumulation of residual arsenic (As) in such soils. In situ immobilization represents a cost-effective and least ecological disrupting treatment technology for soil As. Earlier work in our laboratory showed that drinking-water treatment residuals (WTRs), a low-cost, waste by-product of the drinking-water treatment process exhibit a high affinity for As. Wet chemical experiments (sorption kinetics and desorption) were coupled with X-ray absorption spectroscopy measurements to elucidate the bonding strength and type of As(V) and As(III) sorption by an aluminum-based WTR. A fast (1h), followed by a slower sorption stage resulted in As(V) and As(III) sorption capacities of 96% and 77%, respectively. Arsenic desorption with a 5mM oxalate from the WTR was minimal, being always absorption spectroscopy data showed inner-sphere complexation between As and surface hydroxyls. Reaction time (up to 48h) had no effect on the initial As oxidation state for sorbed As(V) and As(III). A combination of inner-sphere bonding types occurred between As and Al on the WTR surface because mixed surface geometries and interatomic distances were observed.

Technological change in Swiss thermal waste treatment: An expert-based socio-technical analysis

International Nuclear Information System (INIS)

Spoerri, Andy; Lang, Daniel J.; Staeubli, Beat; Scholz, Roland W.

2010-01-01

Understanding technological change provides a crucial basis for governing sustainability transitions. In this paper we present an analysis of technological change using the example of Swiss thermal waste processing. In recent years, increased concerns about the low quality of residues from grate-firing systems led to the examination of alternative technologies. Yet despite clear indications of a potential better performance with respect to residue quality, none of these alternatives has been adopted. Based on a two-stage knowledge integration among 15 leading experts, in a retrospective analysis we identified factors that have significantly affected technological change in Swiss thermal waste processing. These factors were then related to three technological options representing different types of technological change, i.e., from incremental improvements of the existing to the implementation of a new technology. The results indicate that technological change is currently in a technological lock-in and provide detailed insights on the causes. The lock-in results in the step-wise further development of the status quo grate-firing system despite its limitations for improving the residue qualities. Almost all factors (legal, economic, societal, technological) of the existing 'thermal waste management' system have been well adapted to the cost- and energy-efficient grate-firing technology, blocking innovative technologies from entering the Swiss market. In addition, pressures from the context, e.g., societal pressure related to landfill risks, have not been strong enough to promote non-incremental change.

Conceptual Thermal Treatment Technologies Feasibility Study

International Nuclear Information System (INIS)

Suer, A.

1996-01-01

This report presents a conceptual Thermal Treatment Technologies Feasibility Study (FS) for the Savannah River Site (SRS) focusing exclusively on thermal treatment technologies for contaminated soil, sediment, or sludge remediation projects

Modeling of Residual Stress and Machining Distortion in Aerospace Components (PREPRINT)

Science.gov (United States)

2010-03-01

John Gayda, “The Effect of Heat Treatment on Residual Stress and Machining Distortions in Advanced Nickel Base Disk Alloys,” NASA/TM-2001-210717. 2...Wei-Tsu Wu, Guoji Li, Juipeng Tang, Shesh Srivatsa, Ravi Shankar, Ron Wallis, Padu Ramasundaram and John Gayda, “A process modeling system for heat...Materials Processing Technology 98 (2000) 189-195. 6. M.A. Rist, S. Tin, B.A. Roder, J.A. James, and M.R. Daymond , “Residual Stresses in a

Microwave calcination for plutonium immobilization and residue stabilization

Energy Technology Data Exchange (ETDEWEB)

Harris, M.J.; Rising, T.L.; Roushey, W.J.; Sprenger, G.S. [Kaiser-Hill Co., Golden, CO (United States)

1995-12-01

In the late 1980`s development was begun on a process using microwave energy to vitrify low level mixed waste sludge and transuranic mixed waste sludge generated in Building 374 at Rocky Flats. This process was shown to produce a dense, highly durable waste form. With the cessation of weapons production at Rocky Flats, the emphasis has changed from treatment of low level and TRU wastes to stabilizaiton of plutonium oxide and residues. This equipment is versatile and can be used as a heat source to calcine, react or vitrify many types of residues and oxides. It has natural economies in that it heats only the material to be treated, significantly reducing cycle times over conventional furnaces. It is inexpensive to operate in that most of the working components remain outside of any necessary contamination enclosure and therefore can easily be maintained. Limited testing has been successfully performed on cerium oxide (as a surrogate for plutonium oxide), surrogate electrorefining salts, surrogate residue sludge and residue ash. Future plans also include tests on ion exchange resins. In an attempt to further the usefullness of this technology, a mobile, self-contained microwave melting system is currently under development and expected to be operational at Rocky Flats Enviromental Technology Site by the 4th quarter of FY96.

Microwave calcination for plutonium immobilization and residue stabilization

International Nuclear Information System (INIS)

Harris, M.J.; Rising, T.L.; Roushey, W.J.; Sprenger, G.S.

1995-01-01

In the late 1980's development was begun on a process using microwave energy to vitrify low level mixed waste sludge and transuranic mixed waste sludge generated in Building 374 at Rocky Flats. This process was shown to produce a dense, highly durable waste form. With the cessation of weapons production at Rocky Flats, the emphasis has changed from treatment of low level and TRU wastes to stabilizaiton of plutonium oxide and residues. This equipment is versatile and can be used as a heat source to calcine, react or vitrify many types of residues and oxides. It has natural economies in that it heats only the material to be treated, significantly reducing cycle times over conventional furnaces. It is inexpensive to operate in that most of the working components remain outside of any necessary contamination enclosure and therefore can easily be maintained. Limited testing has been successfully performed on cerium oxide (as a surrogate for plutonium oxide), surrogate electrorefining salts, surrogate residue sludge and residue ash. Future plans also include tests on ion exchange resins. In an attempt to further the usefullness of this technology, a mobile, self-contained microwave melting system is currently under development and expected to be operational at Rocky Flats Enviromental Technology Site by the 4th quarter of FY96

New technology of In-Situ-Alcohol-Flushing (ISAF) for mobilizing residual LNAPL in the subsurface by using swelling alcohol

International Nuclear Information System (INIS)

Uhlig, U.; Tranckner, S.; Luckner, L.; Zschiedrich, K.

2005-01-01

The Infiltration of liquid hydrocarbons, the so-called non aqueous phase liquids (NAPL), into the subsurface is a common problem. Our research is focused on light NAPL (LNAPL), which are often trapped as a residual immobile phase (residuals) on the soil matrix. Due to the low solubility of NAPL components in water these residuals form long-term sources of pollution in groundwater. During the last years surfactants (surface active agents) were usually used to increase the efficiency of pump-and-treat aquifer remediation of those contaminated sites. Surfactants increase the solubility of NAPL- components in the aqueous phase, so that the these NAPL-components and surfactants highly contaminate the groundwater. Therefore their application leads to significant costs for treatment of the extracts. Above the critical concentration (critical micelle concentration) surfactants assemble into dynamic clusters called micelles, which are described as droplets of oil with an ionic or polar coating. At concentrations below the CMC surfactants form ad-micelles or hemi-micelles, which are adsorbed on the solid soil matrix. In this way also surfactant-NAPL compounds can be re-adsorbed on the soil matrix. Based on these disadvantages a new technology was developed with the research project 'Investigation for LNAPL - mobilization / solubilization in the subsurface'. This technology for mobilizing residual LNAPL in the subsurface by using swelling alcohol avoids the solution of LNAPL components in the groundwater. Using this new technology the problems arising with the CMC are not relevant. As part of this project, this paper reports results of a field test in Schwarze Pumpe, a former centre of carbo-chemical industry, located in Germany on the border between Saxony and Brandenburg and which covers an area of about 4.5 km 2 . There are three primary contaminated locations and some hot spots, causing considerable groundwater contamination with large plumes. In the centre of pollution

New technology of In-Situ-Alcohol-Flushing (ISAF) for mobilizing residual LNAPL in the subsurface by using swelling alcohol

Energy Technology Data Exchange (ETDEWEB)

Uhlig, U.; Tranckner, S.; Luckner, L. [GFI Groundwater research centre, Dresden (Germany); Zschiedrich, K. [LMBV Lausitz and Central-German Mining Administration Company, Berlin (Germany)

2005-07-01

The Infiltration of liquid hydrocarbons, the so-called non aqueous phase liquids (NAPL), into the subsurface is a common problem. Our research is focused on light NAPL (LNAPL), which are often trapped as a residual immobile phase (residuals) on the soil matrix. Due to the low solubility of NAPL components in water these residuals form long-term sources of pollution in groundwater. During the last years surfactants (surface active agents) were usually used to increase the efficiency of pump-and-treat aquifer remediation of those contaminated sites. Surfactants increase the solubility of NAPL- components in the aqueous phase, so that the these NAPL-components and surfactants highly contaminate the groundwater. Therefore their application leads to significant costs for treatment of the extracts. Above the critical concentration (critical micelle concentration) surfactants assemble into dynamic clusters called micelles, which are described as droplets of oil with an ionic or polar coating. At concentrations below the CMC surfactants form ad-micelles or hemi-micelles, which are adsorbed on the solid soil matrix. In this way also surfactant-NAPL compounds can be re-adsorbed on the soil matrix. Based on these disadvantages a new technology was developed with the research project 'Investigation for LNAPL - mobilization / solubilization in the subsurface'. This technology for mobilizing residual LNAPL in the subsurface by using swelling alcohol avoids the solution of LNAPL components in the groundwater. Using this new technology the problems arising with the CMC are not relevant. As part of this project, this paper reports results of a field test in Schwarze Pumpe, a former centre of carbo-chemical industry, located in Germany on the border between Saxony and Brandenburg and which covers an area of about 4.5 km{sup 2}. There are three primary contaminated locations and some hot spots, causing considerable groundwater contamination with large plumes. In the centre

Residual stress development and relief in high strength aluminium alloys using standard and retrogression thermal treatments

OpenAIRE

Robinson, J.S; Tanner, D.A

2003-01-01

peer-reviewed Residual stresses develop in the aluminium alloy 7010 when the material is quenched from the solution heat treatment temperature. Residual stress measurements have been made using the X-ray diffraction technique and a longitudinal split sawcut method to determine the magnitude of residual stress that develops in specimens sectioned from large open die forgings as a result of (a) quenching these specimens into water at different temperatures, and (b) cold water quenching from ...

Characterization Report on Sand, Slag, and Crucible Residues and on Fluoride Residues

International Nuclear Information System (INIS)

Murray, A.M.

1999-01-01

This paper reports on the chemical characterization of the sand, slag, and crucible (SS and C) residues and the fluoride residues that may be shipped from the Rocky Flats Environmental Technology Site (RFETS) to Savannah River Site (SRS)

Safe apples for baby-food production: survey of pesticide treatment regimes leaving minimum residues.

Science.gov (United States)

Ticha, Jana; Hajslova, Jana; Kovalczuk, Tomas; Jech, Martin; Honzicek, Jiri; Kocourek, Vladimir; Lansky, Miroslav; Kloutvorova, Jana; Falta, Vladan

2007-06-01

A total of 19 pesticide preparations were used according to agricultural practice in six trials in apple orchards. Using gas chromatography-mass spectrometry (GC-MS) and liquid chromatography-tandem mass spectrometry (LC-MS/MS), premature Golden Delicious apples collected 64, 50, 36 days before harvest and mature fruit were examined for residues of active ingredients. No residues of triflumuron, triazamate, chlorpyrifos, etofenprox, fenoxycarb, kresoxim-methyl, cyprodinyl, difenoconazole or thiram were detected in the first sampling. Also, the levels of chlorpyrifos-methyl, penconazole, tebuconazole and tolylfluanid dropped during the pre-harvest interval. Detectable residues of pyridaben, thiacloprid, trifloxystrobin and tetraconazole in harvested fruits were below 0.01 mg kg(-1), which is the maximum concentration of residues acceptable by baby-food producers in any raw material. The only residues exceeding this concentration were captan and teflubenzuron. Based on the data, farmers can choose pesticides for optimal treatment of plants, while enabling growth of a safe crop suitable for baby-food production.

A previously undescribed organic residue sheds light on heat treatment in the Middle Stone Age.

Science.gov (United States)

Schmidt, Patrick; Porraz, Guillaume; Bellot-Gurlet, Ludovic; February, Edmund; Ligouis, Bertrand; Paris, Céline; Texier, Pierre-Jean; Parkington, John E; Miller, Christopher E; Nickel, Klaus G; Conard, Nicholas J

2015-08-01

South Africa has in recent years gained increasing importance for our understanding of the evolution of 'modern human behaviour' during the Middle Stone Age (MSA). A key element in the suite of behaviours linked with modern humans is heat treatment of materials such as ochre for ritual purposes and stone prior to tool production. Until now, there has been no direct archaeological evidence for the exact procedure used in the heat treatment of silcrete. Through the analysis of heat-treated artefacts from the Howiesons Poort of Diepkloof Rock Shelter, we identified a hitherto unknown type of organic residue - a tempering-residue - that sheds light on the processes used for heat treatment in the MSA. This black film on the silcrete surface is an organic tar that contains microscopic fragments of charcoal and formed as a residue during the direct contact of the artefacts with hot embers of green wood. Our results suggest that heat treatment of silcrete was conducted directly using an open fire, similar to those likely used for cooking. These findings add to the discussion about the complexity of MSA behaviour and appear to contradict previous studies that had suggested that heat treatment of silcrete was a complex (i.e., requiring a large number of steps for its realization) and resource-consuming procedure. Copyright © 2015 Elsevier Ltd. All rights reserved.

Sources of manganese in the residue from a water treatment plant ...

African Journals Online (AJOL)

Disposal of water treatment residue (WTR), the by-product from the production of potable water, has traditionally been to landfill. The shortage of suitable landfill sites has led to the proposal that WTR be applied to land. Such disposal is only possible if the WTR contains no toxic elements that may contaminate soil, water or ...

Development of high-level radioactive waste treatment and conversion technologies 'Dry decontamination technology development for highly radioactive contaminants'

International Nuclear Information System (INIS)

Oh, Won Zin; Lee, K. W.; Won, H. J.; Jung, C. J.; Choi, W. K.; Kim, G. N.; Moon, J. K.

2001-04-01

The followings were studied through the project entitled 'Dry Decontamination Technology Development for Highly Radioactive Contaminants'. 1.Contaminant Characteristics Analysis of Domestic Nuclear Fuel Cycle Projects(NFCP) and Applicability Study of the Unit Dry-Decontamination Techniques A. Classification of contaminated equipments and characteristics analysis of contaminants B. Applicability study of the unit dry-decontamination techniques 2.Performance Evaluation of Unit Dry Decontamination Technique A. PFC decontamination technique B. CO2 decontamination technique C. Plasma decontamination technique 3.Development of Residual Radiation Assessment Methodology for High Radioactive Facility Decontamination A. Development of radioactive nuclide diffusion model on highly radioactive facility structure B. Obtainment of the procedure for assessment of residual radiation dose 4.Establishment of the Design Concept of Dry Decontamination Process Equipment Applicable to Highly Radioactive Contaminants 5.TRIGA soil unit decontamination technology development A. Development of soil washing and flushing technologies B. Development of electrokinetic soil decontamination technology

Residual gas analysis

International Nuclear Information System (INIS)

Berecz, I.

1982-01-01

Determination of the residual gas composition in vacuum systems by a special mass spectrometric method was presented. The quadrupole mass spectrometer (QMS) and its application in thin film technology was discussed. Results, partial pressure versus time curves as well as the line spectra of the residual gases in case of the vaporization of a Ti-Pd-Au alloy were demonstrated together with the possible construction schemes of QMS residual gas analysers. (Sz.J.)

Technologies 1995: environment and wastes treatment

International Nuclear Information System (INIS)

Anon.

1995-03-01

From new technical or scientific developments, new products launching, and markets evolutions, this catalog gives informations selection on research and development projects, new fabrication processes, activities and plants strategies, licences or technology transfers opportunities. The covered fields are: atmospheric pollution controls, water and liquid wastes treatment, polluted soils treatments, noise and odors treatments, municipal and industrial wastes treatments (metal, plastic, paper, glass), clean materials and technologies, radioactive wastes, and european cooperation programs. (A.B.)

Metal-containing residues from industry and in the environment: geobiotechnological urban mining.

Science.gov (United States)

Glombitza, Franz; Reichel, Susan

2014-01-01

This chapter explains the manifold geobiotechnological possibilities to separate industrial valuable metals from various industrial residues and stored waste products of the past. In addition to an overview of the different microbially catalyzed chemical reactions applicable for a separation of metals and details of published studies, results of many individual investigations from various research projects are described. These concern the separation of rare earth elements from phosphorous production slags, the attempts of tin leaching from mining flotation residues, the separation of metals from spent catalysts, or the treatment of ashes as valuable metal-containing material. The residues of environmental technologies are integrated into this overview as well. The description of the different known microbial processes offers starting points for suitable and new technologies. In addition to the application of chemolithoautotrophic microorganisms the use of heterotrophic microorganisms is explained.

Research on Toxicity Evaluation of Waste Incineration Residues of Printed Circuit Boards

Directory of Open Access Journals (Sweden)

Rasa Volungevičienė

2014-10-01

Full Text Available Recycling waste printed circuit boards (PCB is an extremely complicated process, because PCBs consist of a number of complex components – hazardous and non-hazardous materials sets. Pyrolysis and combustion are currently the most effective treatment technologies for waste printed circuit boards. Pyrolysis can be used for thermally decomposing PCBs allowing for the simultaneous recovery of valuable materials. Following the extraction of valuable materials, the problem of residual ash utilization is encountered. Determining the qualitative and quantitative characteristics of incineration residue helps with choosing effective ash management technologies. This paper analyzes PCB ash generated at three different temperatures of 400 °C, 500 °C and 600 °C. Ash residues have been analysed to determine the quantity and type of metals present. Furthermore, the experiment of leaching heavy metals from ash has been described.

An overview of in situ waste treatment technologies

International Nuclear Information System (INIS)

Walker, S.; Hyde, R.A.; Piper, R.B.; Roy, M.W.

1992-01-01

In situ technologies are becoming an attractive remedial alternative for eliminating environmental problems. In situ treatments typically reduce risks and costs associated with retrieving, packaging, and storing or disposing-waste and are generally preferred over ex situ treatments. Each in situ technology has specific applications, and, in order to provide the most economical and practical solution to a waste problem, these applications must be understood. This paper presents an overview of thirty different in situ remedial technologies for buried wastes or contaminated soil areas. The objective of this paper is to familiarize those involved in waste remediation activities with available and emerging in situ technologies so that they may consider these options in the remediation of hazardous and/or radioactive waste sites. Several types of in situ technologies are discussed, including biological treatments, containment technologies, physical/chemical treatments, solidification/stabilization technologies, and thermal treatments. Each category of in situ technology is briefly examined in this paper. Specific treatments belonging to these categories are also reviewed. Much of the information on in situ treatment technologies in this paper was obtained directly from vendors and universities and this information has not been verified

Technology assessment of thermal treatment technologies using ORWARE

International Nuclear Information System (INIS)

Assefa, G.; Eriksson, O.; Frostell, B.

2005-01-01

A technology assessment of thermal treatment technologies for wastes was performed in the form of scenarios of chains of technologies. The Swedish assessment tool, ORWARE, was used for the assessment. The scenarios of chains of thermal technologies assessed were gasification with catalytic combustion, gasification with flame combustion, incineration and landfilling. The landfilling scenario was used as a reference for comparison. The technologies were assessed from ecological and economic points of view. The results are presented in terms of global warming potential, acidification potential, eutrophication potential, consumption of primary energy carriers and welfare costs. From the simulations, gasification followed by catalytic combustion with energy recovery in a combined cycle appeared to be the most competitive technology from an ecological point of view. On the other hand, this alternative was more expensive than incineration. A sensitivity analysis was done regarding electricity prices to show which technology wins at what value of the unit price of electricity (SEK/kW h). Within this study, it was possible to make a comparison both between a combined cycle and a Rankine cycle (a system pair) and at the same time between flame combustion and catalytic combustion (a technology pair). To use gasification just as a treatment technology is not more appealing than incineration, but the possibility of combining gasification with a combined cycle is attractive in terms of electricity production. This research was done in connection with an empirical R and D work on both gasification of waste and catalytic combustion of the gasified waste at the Division of Chemical Technology, Royal Institute of Technology (KTH), Sweden

Resource and energy recovery options for fermentation industry residuals

Energy Technology Data Exchange (ETDEWEB)

Chiesa, S C [Santa Clara Univ., CA (USA); Manning, Jr, J F [Alabama Univ., Birmingham, AL (USA)

1989-01-01

Over the last 40 years, the fermentation industry has provided facility planners, plant operators and environmental engineers with a wide range of residuals management challenges and resource/energy recovery opportunities. In response, the industry has helped pioneer the use of a number of innovative resource and energy recovery technologies. Production of animal feed supplements, composts, fertilizers, soil amendments, commercial baking additives and microbial protein materials have all been detailed in the literature. In many such cases, recovery of by-products significantly reduces the need for treatment and disposal facilities. Stable, reliable anaerobic biological treatment processes have also been developed to recover significant amounts of energy in the form of methane gas. Alternatively, dewatered or condensed organic fermentation industry residuals have been used as fuels for incineration-based energy recovery systems. The sale or use of recovered by-products and/or energy can be used to offset required processing costs and provide a technically and environmentally viable alternative to traditional treatment and disposal strategies. This review examines resource recovery options currently used or proposed for fermentation industry residuals and the conditions necessary for their successful application. (author).

Minimization of Residual Stress in an Al-Cu Alloy Forged Plate by Different Heat Treatments

Science.gov (United States)

Dong, Ya-Bo; Shao, Wen-Zhu; Jiang, Jian-Tang; Zhang, Bao-You; Zhen, Liang

2015-06-01

In order to improve the balance of mechanical properties and residual stress, various quenching and aging treatments were applied to Al-Cu alloy forged plate. Residual stresses determined by the x-ray diffraction method and slitting method were compared. The surface residual stress measured by x-ray diffraction method was consistent with that measured by slitting method. The residual stress distribution of samples quenched in water with different temperatures (20, 60, 80, and 100 °C) was measured, and the results showed that the boiling water quenching results in a 91.4% reduction in residual stress magnitudes compared with cold water quenching (20 °C), but the tensile properties of samples quenched in boiling water were unacceptably low. Quenching in 80 °C water results in 75% reduction of residual stress, and the reduction of yield strength is 12.7%. The residual stress and yield strength level are considerable for the dimensional stability of aluminum alloy. Quenching samples into 30% polyalkylene glycol quenchants produced 52.2% reduction in the maximum compressive residual stress, and the reduction in yield strength is 19.7%. Moreover, the effects of uphill quenching and thermal-cold cycling on the residual stress were also investigated. Uphill quenching and thermal-cold cycling produced approximately 25-40% reduction in residual stress, while the effect on tensile properties is quite slight.

TREATMENT OF METAL-LADEN HAZARDOUS WASTES WITH ADVANCED CLEAN COAL TECHNOLOGY BY-PRODUCTS

Energy Technology Data Exchange (ETDEWEB)

James T. Cobb, Jr.

2003-09-12

Metal-laden wastes can be stabilized and solidified using advanced clean coal technology by-products (CCTBs)--fluid bed combustor ash and spray drier solids. These utility-generated treatment chemicals are available for purchase through brokers, and commercial applications of this process are being practiced by treaters of metal-laden hazardous waste. A complex of regulations governs this industry, and sensitivities to this complex has discouraged public documentation of treatment of metal-laden hazardous wastes with CCTBs. This report provides a comprehensive public documentation of laboratory studies that show the efficacy of the stabilization and solidification of metal-laden hazardous wastes--such as lead-contaminated soils and sandblast residues--through treatment with CCTBs. It then describes the extensive efforts that were made to obtain the permits allowing a commercial hazardous waste treater to utilize CCTBs as treatment chemicals and to install the equipment required to do so. It concludes with the effect of this lengthy process on the ability of the treatment company to realize the practical, physical outcome of this effort, leading to premature termination of the project.

Sodium-Bearing Waste Treatment, Applied Technology Plan

International Nuclear Information System (INIS)

Lance Lauerhass; Vince C. Maio; S. Kenneth Merrill; Arlin L. Olson; Keith J. Perry

2003-01-01

Settlement Agreement between the Department of Energy and the State of Idaho mandates treatment of sodium-bearing waste at the Idaho Nuclear Technology and Engineering Center within the Idaho National Engineering and Environmental Laboratory. One of the requirements of the Settlement Agreement is to complete treatment of sodium-bearing waste by December 31, 2012. Applied technology activities are required to provide the data necessary to complete conceptual design of four identified alternative processes and to select the preferred alternative. To provide a technically defensible path forward for the selection of a treatment process and for the collection of needed data, an applied technology plan is required. This document presents that plan, identifying key elements of the decision process and the steps necessary to obtain the required data in support of both the decision and the conceptual design. The Sodium-Bearing Waste Treatment Applied Technology Plan has been prepared to provide a description/roadmap of the treatment alternative selection process. The plan details the results of risk analyzes and the resulting prioritized uncertainties. It presents a high-level flow diagram governing the technology decision process, as well as detailed roadmaps for each technology. The roadmaps describe the technical steps necessary in obtaining data to quantify and reduce the technical uncertainties associated with each alternative treatment process. This plan also describes the final products that will be delivered to the Department of Energy Idaho Operations Office in support of the office's selection of the final treatment technology

Sodium-Bearing Waste Treatment, Applied Technology Plan

Energy Technology Data Exchange (ETDEWEB)

Lance Lauerhass; Vince C. Maio; S. Kenneth Merrill; Arlin L. Olson; Keith J. Perry

2003-06-01

Settlement Agreement between the Department of Energy and the State of Idaho mandates treatment of sodium-bearing waste at the Idaho Nuclear Technology and Engineering Center within the Idaho National Engineering and Environmental Laboratory. One of the requirements of the Settlement Agreement is to complete treatment of sodium-bearing waste by December 31, 2012. Applied technology activities are required to provide the data necessary to complete conceptual design of four identified alternative processes and to select the preferred alternative. To provide a technically defensible path forward for the selection of a treatment process and for the collection of needed data, an applied technology plan is required. This document presents that plan, identifying key elements of the decision process and the steps necessary to obtain the required data in support of both the decision and the conceptual design. The Sodium-Bearing Waste Treatment Applied Technology Plan has been prepared to provide a description/roadmap of the treatment alternative selection process. The plan details the results of risk analyzes and the resulting prioritized uncertainties. It presents a high-level flow diagram governing the technology decision process, as well as detailed roadmaps for each technology. The roadmaps describe the technical steps necessary in obtaining data to quantify and reduce the technical uncertainties associated with each alternative treatment process. This plan also describes the final products that will be delivered to the Department of Energy Idaho Operations Office in support of the office's selection of the final treatment technology.

Life-cycle assessment of selected management options for air pollution control residues from waste incineration.

Science.gov (United States)

Fruergaard, Thilde; Hyks, Jiri; Astrup, Thomas

2010-09-15

Based on available technology and emission data seven selected management options for air-pollution-control (APC) residues from waste incineration were evaluated by life-cycle assessment (LCA) using the EASEWASTE model. Scenarios were evaluated with respect to both non-toxicity impact categories (e.g. global warming) and toxicity related impact categories (e.g. ecotoxicity and human toxicity). The assessment addressed treatment and final placement of 1 tonne of APC residue in seven scenarios: 1) direct landfilling without treatment (baseline), 2) backfilling in salt mines, 3) neutralization of waste acid, 4) filler material in asphalt, 5) Ferrox stabilization, 6) vitrification, and 7) melting with automobile shredder residues (ASR). The management scenarios were selected as examples of the wide range of different technologies available worldwide while at the same time using realistic technology data. Results from the LCA were discussed with respect to importance of: energy consumption/substitution, material substitution, leaching, air emissions, time horizon aspects for the assessment, and transportation distances. The LCA modeling showed that thermal processes were associated with the highest loads in the non-toxicity categories (energy consumption), while differences between the remaining alternatives were small and generally considered insignificant. In the toxicity categories, all treatment/utilization options were significantly better than direct landfilling without treatment (lower leaching), although the thermal processes had somewhat higher impacts than the others options (air emissions). Transportation distances did not affect the overall ranking of the management alternatives. Copyright 2010 Elsevier B.V. All rights reserved.

Effect of water treatment residuals on soil phosphorus, copper and aluminium availability and toxicity

Energy Technology Data Exchange (ETDEWEB)

Lombi, E., E-mail: enzo.lombi@unisa.edu.a [CSIRO Land and Water, Centre for Environmental Contaminant Research, PMB 2, Glen Osmond, SA 5064 (Australia); Centre for Environmental Risk Assessment and Remediation, University of South Australia, Building X, Mawson Lakes Campus, Mawson Lakes, SA 5095 (Australia); CRC CARE, PO Box 486, Salisbury, SA 5106 (Australia); Stevens, D.P. [CSIRO Land and Water, Centre for Environmental Contaminant Research, PMB 2, Glen Osmond, SA 5064 (Australia); Arris Pty Ltd, PO Box 5143, Burnley, Victoria 3121 (Australia); McLaughlin, M.J. [CSIRO Land and Water, Centre for Environmental Contaminant Research, PMB 2, Glen Osmond, SA 5064 (Australia); Soil and Land Systems, University of Adelaide, PMB 1, Glen Osmond, SA 5064 (Australia)

2010-06-15

Water treatment residuals (WTRs) are produced by the treatment of potable water with coagulating agents. Beneficial recycling in agriculture is hampered by the fact that WTRs contain potentially toxic contaminants (e.g. copper and aluminium) and they bind phosphorus strongly. These issues were investigated using a plant bioassay (Lactuca sativa), chemical extractions and an isotopic dilution technique. Two WTRs were applied to an acidic and a neutral pH soil at six rates. Reductions in plant growth in amended soils were due to WTR-induced P deficiency, rather than Al or Cu toxicity. The release of potentially toxic Al from WTRs was found to be mitigated by their alkaline nature and pH buffering capacity. However, acidification of WTRs was shown to release more soluble Al than soil naturally high in Al. Copper availability was relatively low in all treatments. However, the lability of WTR-Cu increased when the WTR was applied to the soil. - The effect of water treatment residue application to soil was investigated in relation to phosphorus availability, and copper and aluminium phytotoxicity.

Effect of water treatment residuals on soil phosphorus, copper and aluminium availability and toxicity

International Nuclear Information System (INIS)

Lombi, E.; Stevens, D.P.; McLaughlin, M.J.

2010-01-01

Water treatment residuals (WTRs) are produced by the treatment of potable water with coagulating agents. Beneficial recycling in agriculture is hampered by the fact that WTRs contain potentially toxic contaminants (e.g. copper and aluminium) and they bind phosphorus strongly. These issues were investigated using a plant bioassay (Lactuca sativa), chemical extractions and an isotopic dilution technique. Two WTRs were applied to an acidic and a neutral pH soil at six rates. Reductions in plant growth in amended soils were due to WTR-induced P deficiency, rather than Al or Cu toxicity. The release of potentially toxic Al from WTRs was found to be mitigated by their alkaline nature and pH buffering capacity. However, acidification of WTRs was shown to release more soluble Al than soil naturally high in Al. Copper availability was relatively low in all treatments. However, the lability of WTR-Cu increased when the WTR was applied to the soil. - The effect of water treatment residue application to soil was investigated in relation to phosphorus availability, and copper and aluminium phytotoxicity.

Indigenous microbial capability in solid manure residues to start-up solid-phase anaerobic digesters.

Science.gov (United States)

Yap, S D; Astals, S; Jensen, P D; Batstone, D J; Tait, S

2017-06-01

Batch solid-phase anaerobic digestion is a technology for sustainable on-farm treatment of solid residues, but is an emerging technology that is yet to be optimised with respect to start-up and inoculation. In the present study, spent bedding from two piggeries (site A and B) were batch digested at total solids (TS) concentration of 5, 10 and 20% at mesophilic (37°C) and thermophilic (55°C) temperatures, without adding an external inoculum. The results showed that the indigenous microbial community present in spent bedding was able to recover the full methane potential of the bedding (140±5 and 227±6L CH 4 kgVS fed -1 for site A and B, respectively), but longer treatment times were required than for digestion with an added external inoculum. Nonetheless, at high solid loadings (i.e. TS level>10%), the digestion performance was affected by chemical inhibition due to ammonia and/or humic acid. Thermophilic temperatures did not influence digestion performance but did increase start-up failure risk. Further, inoculation of residues from the batch digestion to subsequent batch enhanced start-up and achieved full methane potential recovery of the bedding. Inoculation with liquid residue (leachate) was preferred over a solid residue, to preserve treatment capacity for fresh substrate. Overall, the study highlighted that indigenous microbial community in the solid manure residue was capable of recovering full methane potential and that solid-phase digestion was ultimately limited by chemical inhibition rather than lack of suitable microbial community. Copyright © 2017 Elsevier Ltd. All rights reserved.

Forest treatment residues for thermal energy compared with disposal by onsite burning: Emissions and energy return

Science.gov (United States)

Greg Jones; Dan Loeffler; David Calkin; Woodam Chung

2010-01-01

Mill residues from forest industries are the source for most of the current wood-based energy in the US, approximately 2.1% of the nation's energy use in 2007. Forest residues from silvicultural treatments, which include limbs, tops, and small non-commercial trees removed for various forest management objectives, represent an additional source of woody biomass for...

Development of ecologically safety technology for steam-thermal treatment of organic wastes

International Nuclear Information System (INIS)

Juravskij, J.

1997-01-01

The experience on mitigation of the consequences of the Chernobyl's nuclear power station accident proves that the treatment of large amounts of organic and mixed wastes containing radionuclides is a very urgent scientific and technical problem. In this connection a search for new ideas and development of highly efficient and ecologically safety technologies for treatment of organic radioactive wastes has been undertaken. This study is based on use of physico-mechanical properties of various organic materials (wood, rubber-containing composites, plastics, biomass) subjected to thermal decomposition in the overheated water steam medium. Under such conditions, there is a possibility, under relatively low temperatures (400 - 500 deg. C), to realize thermal decomposition and considerably (in 8 - 50 times) to reduce the amount of wastes, to obtain the main concentration of radionuclides in the solid residue and to prevent releases of gaseous products containing radionuclides to the environment. (author). 5 figs, 1 tab

Radioactive Dry Process Material Treatment Technology Development

Energy Technology Data Exchange (ETDEWEB)

Park, J. J.; Hung, I. H.; Kim, K. K. (and others)

2007-06-15

The project 'Radioactive Dry Process Material Treatment Technology Development' aims to be normal operation for the experiments at DUPIC fuel development facility (DFDF) and safe operation of the facility through the technology developments such as remote operation, maintenance and pair of the facility, treatment of various high level process wastes and trapping of volatile process gases. DUPIC Fuel Development Facility (DFDF) can accommodate highly active nuclear materials, and now it is for fabrication of the oxide fuel by dry process characterizing the proliferation resistance. During the second stage from march 2005 to February 2007, we carried out technology development of the remote maintenance and the DFDF's safe operation, development of treatment technology for process off-gas, and development of treatment technology for PWR cladding hull and the results was described in this report.

Tracking the conversion of nitrogen during pyrolysis of antibiotic mycelial fermentation residues using XPS and TG-FTIR-MS technology

International Nuclear Information System (INIS)

Zhu, Xiangdong; Yang, Shijun; Wang, Liang; Liu, Yuchen; Qian, Feng; Yao, Wenqing; Zhang, Shicheng; Chen, Jianmin

2016-01-01

Antibiotic mycelial fermentation residues (AMFRs), which are emerging solid pollutants, have been recognized as hazardous waste in China since 2008. Nitrogen (N), which is an environmental sensitivity element, is largely retained in AMFR samples derived from fermentation substrates. Pyrolysis is a promising technology for the treatment of solid waste. However, the outcomes of N element during the pyrolysis of AMFRs are still unknown. In this study, the conversion of N element during the pyrolysis of AMFRs was tracked using XPS (X-ray photoelectron spectroscopy) and online TG-FTIR-MS (Thermogravimetry-Fourier transform infrared-Mass spectrometry) technology. In the AMFR sample, organic amine-N, pyrrolic-N, protein-N, pyridinic-N, was the main N-containing species. XPS results indicated that pyrrolic-N and pyridinic-N were retained in the AMFR-derived pyrolysis char. More stable species, such as N-oxide and quaternary-N, were also produced in the char. TG-FTIR-MS results indicated that NH_3 and HCN were the main gaseous species, and their contents were closely related to the contents of amine-N and protein-N, and pyrrolic-N and pyridinic-N of AMFRs, respectively. Increases in heating rate enhanced the amounts of NH_3 and HCN, but had less of an effect on the degradation degree of AMFRs. N-containing organic compounds, including amine-N, nitrile-N and heterocyclic-N, were discerned from the AMFR pyrolysis process. Their release range was extended with increasing of heating rate and carbon content of AMFR sample. This work will help to take appropriate measure to reduce secondary pollution from the treatment of AMFRs. - Highlights: • Hazardous AMFR material was treated by slow pyrolysis reaction. • TG-FTIR-MS were used to study the N conversion for pyrolysis gas and bio-oil. • NH_3 and HCN were observed as the main N-containing gas species. • XPS were used to study the N conversion for pyrolysis char. • Stable species, such as N-oxide and quaternary-N, were

Effect of shot peening treatment in the behavior of residual stress in duplex stainless steel during medium cycle fatigue

International Nuclear Information System (INIS)

Pedrosa, Peter D.S.; Rebello, Joao Marcos A.; Fonseca, Maria P. Cindra

2010-01-01

The lifetime of duplex stainless steel parts experiencing cyclic fatigue is directly influenced by the residual stresses present in the ferrite and austenite phases. The motivation for this work was to analyze the behaviour of the residual stresses fields introduced by shot peening treatment in both phases, in the sample surface as in the subsurface layers, in low fatigue cycles, using the X-rays diffraction technique. The results shows that the compressive residual stresses introduced by the shot peening treatment in both phases improved fatigue life of the material. However, the cyclical loads produce partial or total relief in these residual stresses fields. It was verified that the shot peening process induced the formation of microcracks only in the ferrite phase. The largest variations in the total compressive residual stresses fields also occurred in this phase. The samples surfaces were analyzed by scanning electron microscopy. (author)

Measurement of heat treatment induced residual stresses by using ESPI combined with hole-drilling method

Directory of Open Access Journals (Sweden)

Jie Cheng

2010-08-01

Full Text Available In this study, residual stresses in heat treated specimen were measured by using ESPI (Electronic Speckle-Pattern Interferometry combined with the hole-drilling method. The specimen, made of SUS 304 austenitic stainless steel, was quenched and water cooled to room temperature. Numerical simulation using a hybrid FDM/FEM package was also carried out to simulate the heat treatment process. As a result, the thermal stress fields were obtained from both the experiment and the numerical simulation. By comparision of stress fields, results from the experimental method and numerical simulation well agreed to each other, therefore, it is proved that the presented experimental method is applicable and reliable for heat treatment induced residual stress measurement.

Life cycle assessment of innovative technology for energy production from automotive shredder residue.

Science.gov (United States)

Rinaldi, Caterina; Masoni, Paolo; Salvati, Fabio; Tolve, Pietro

2015-07-01

Automotive Shredder Residue (ASR) is a problematic waste material remaining after shredding and recovery processes of end-of-life vehicles (ELVs). Its heterogeneous grain size and composition make difficult its recovery or disposal. Although ASR accounts for approximately 20% to 25% of the weight of an ELV, the European Union (EU)'s ELV Directive (2000/53/EC) requires that by 2015 a minimum 95% of the weight of an ELV must be reused or recovered, including a 10% weight energy recovery. The quantity of ASR is relevant: Approximately 2.4 million tons are generated in the EU each year and most of it is sent to landfills. This article describes a life cycle model of the "TEKNE-Fluff" process designed to make beneficial use of ASR that is based on the results of an experimental pilot plant for pyro-gasification, combustion, cogeneration, and emissions treatment of ASR. The goal of the research was the application of life cycle assessment (LCA) methodology to identify the environmental hot spots of the "TEKNE system" and use scenario analysis to check solutions to improve its environmental profile, supporting the design and industrialization process. The LCA was conducted based on data modeled from the experimental campaign. Moreover, different scenarios on shares of electricity and thermal energy produced by the cogeneration system and alternative treatment processes for the waste produced by the technology were compared. Despite the limitation of the research (results based on scaling up experimental data by modeling), impact assessment results are promising and sufficiently robust, as shown by Monte Carlo analysis. The TEKNE technology may become an interesting solution for the problem of ASR management: Besides representing an alternative to landfill disposal, the energy produced could avoid significant impacts on fossil resources depletion (a plant of 40,000 tons/y capacity could produce ∼ 147,000 GJ/yr, covering the annual need of ∼ 13,500 households). © 2015

Nuclear fuel cycle waste recycling technology deverlopment - Radioactive metal waste recycling technology development

International Nuclear Information System (INIS)

Oh, Won Zin; Moon, Jei Kwon; Jung, Chong Hun; Park, Sang Yoon

1998-08-01

With relation to recycling of the radioactive metal wastes which are generated during operation and decommissioning of nuclear facilities, the following were described in this report. 1. Analysis of the state of the art on the radioactive metal waste recycling technologies. 2. Economical assessment on the radioactive metal waste recycling. 3. Process development for radioactive metal waste recycling, A. Decontamination technologies for radioactive metal waste recycling. B. Decontamination waste treatment technologies, C. Residual radioactivity evaluation technologies. (author). 238 refs., 60 tabs., 79 figs

Life cycle assessment of integrated solid state anaerobic digestion and composting for on-farm organic residues treatment.

Science.gov (United States)

Li, Yangyang; Manandhar, Ashish; Li, Guoxue; Shah, Ajay

2018-03-20

Driven by the gradual changes in the structure of energy consumption and improvements of living standards in China, the volume of on-farm organic solid waste is increasing. If untreated, these unutilized on-farm organic solid wastes can cause environmental problems. This paper presents the results of a life cycle assessment to compare the environmental impacts of different on-farm organic waste (which includes dairy manure, corn stover and tomato residue) treatment strategies, including anaerobic digestion (AD), composting, and AD followed by composting. The input life cycle inventory data are specific to China. The potential environmental impacts of different waste management strategies were assessed based on their acidification potential (AP), eutrophication potential (EP), global warming potential (GWP), ecotoxicity potential (ETP), and resource depletion (RD). The results show that the preferred treatment strategy for dairy manure is the one that integrated corn stover and tomato residue utilization and solid state AD technologies into the system. The GWP of integrated solid state AD and composting was the least, which is -2900 kg CO 2 eq/ t of dairy manure and approximately 14.8 times less than that of current status (i.e., liquid AD of dairy manure). Solid state AD of dairy manure, corn stover and tomato residues is the most favorable option in terms of AP, EP and ETP, which are more than 40% lower than that of the current status (i.e., AP: 3.11 kg SO 2 , EP: -0.94 kg N, and ETP: -881 CTUe (Comparative Toxic Units ecotoxicity)). The results also show that there is a significant potential for AP, EP, ETP, and GWP reduction, if AD is used prior to composting. The scenario analysis for transportation distance showed that locating the AD plant and composting facility on the farm was advantageous in terms of all the life cycle impact categories. Copyright © 2018 Elsevier Ltd. All rights reserved.

RESIDUAL RISK ASSESSMENT: ETHYLENE OXIDE ...

Science.gov (United States)

This document describes the residual risk assessment for the Ethylene Oxide Commercial Sterilization source category. For stationary sources, section 112 (f) of the Clean Air Act requires EPA to assess risks to human health and the environment following implementation of technology-based control standards. If these technology-based control standards do not provide an ample margin of safety, then EPA is required to promulgate addtional standards. This document describes the methodology and results of the residual risk assessment performed for the Ethylene Oxide Commercial Sterilization source category. The results of this analyiss will assist EPA in determining whether a residual risk rule for this source category is appropriate.

Effects of post weld heat treatment and weld overlay on the residual stress and mechanical properties in dissimilar metal weld

International Nuclear Information System (INIS)

Campos, Wagner R.C.; Ribeiro, Vladimir S.; Vilela, Alisson H.F.; Almeida, Camila R.O.; Rabello, Emerson G.

2017-01-01

The object of this work is a dissimilar metal weld (DMW) pipe joint between carbon steel (A-106 Gr B) and stainless steel (A-312 TP316L) pipes and filler metals of Nickel alloy (82/182), which find wide application in the field of chemical, oil, petroleum industries, fossil fuel and nuclear power plant. A lot of the failures that have occurred in dissimilar metal welded are affected greatly by residual stresses. Residual stress is often a cause of premature failure of critical components under normal operation of welded components. Several methods have been tested and developed for removing the tensile residual stresses. The aim of the methods is to reduce the tensile stress state or to create compressive stresses at a predefined area, such as the inner surface of a welded pipe joint. Post weld heat treatment (PWHT) and weld overlay (WOL) are two of the residual stress mitigation methods which reduce the tensile residual stress, create compressive stresses and arrest crack initiation and crack growth. The technique used to substantially minimized or eliminated this failure development in the root weld is the post weld heat treatments (stress relief heat treatment) or the weld overlay. In this work was studied the effectiveness in reducing internal residual stress in dissimilar metal welded pipe joints subjected to post weld heat treatment and weld overlay, measurement by hole-drilling strain-gage method of stress relaxation. Also held was mechanical characterization of the welded pipe joint itself. (author)

Effects of post weld heat treatment and weld overlay on the residual stress and mechanical properties in dissimilar metal weld

Energy Technology Data Exchange (ETDEWEB)

Campos, Wagner R.C.; Ribeiro, Vladimir S.; Vilela, Alisson H.F.; Almeida, Camila R.O.; Rabello, Emerson G., E-mail: wrcc@cdtn.br, E-mail: camilarezende.cr@gmail.com, E-mail: egr@cdtn.br, E-mail: vladimirsoler@hotmail.com, E-mail: ahfv02@outlook.com [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

2017-07-01

The object of this work is a dissimilar metal weld (DMW) pipe joint between carbon steel (A-106 Gr B) and stainless steel (A-312 TP316L) pipes and filler metals of Nickel alloy (82/182), which find wide application in the field of chemical, oil, petroleum industries, fossil fuel and nuclear power plant. A lot of the failures that have occurred in dissimilar metal welded are affected greatly by residual stresses. Residual stress is often a cause of premature failure of critical components under normal operation of welded components. Several methods have been tested and developed for removing the tensile residual stresses. The aim of the methods is to reduce the tensile stress state or to create compressive stresses at a predefined area, such as the inner surface of a welded pipe joint. Post weld heat treatment (PWHT) and weld overlay (WOL) are two of the residual stress mitigation methods which reduce the tensile residual stress, create compressive stresses and arrest crack initiation and crack growth. The technique used to substantially minimized or eliminated this failure development in the root weld is the post weld heat treatments (stress relief heat treatment) or the weld overlay. In this work was studied the effectiveness in reducing internal residual stress in dissimilar metal welded pipe joints subjected to post weld heat treatment and weld overlay, measurement by hole-drilling strain-gage method of stress relaxation. Also held was mechanical characterization of the welded pipe joint itself. (author)

On the ASR and ASR thermal residues characterization of full scale treatment plant.

Science.gov (United States)

Mancini, G; Viotti, P; Luciano, A; Fino, D

2014-02-01

In order to obtain 85% recycling, several procedures on Automotive Shredder Residue (ASR) could be implemented, such as advanced metal and polymer recovery, mechanical recycling, pyrolysis, the direct use of ASR in the cement industry, and/or the direct use of ASR as a secondary raw material. However, many of these recovery options appear to be limited, due to the possible low acceptability of ASR based products on the market. The recovery of bottom ash and slag after an ASR thermal treatment is an option that is not usually considered in most countries (e.g. Italy) due to the excessive amount of contaminants, especially metals. The purpose of this paper is to provide information on the characteristics of ASR and its full-scale incineration residues. Experiments have been carried out, in two different experimental campaigns, in a full-scale tyre incineration plant specifically modified to treat ASR waste. Detailed analysis of ASR samples and combustion residues were carried out and compared with literature data. On the basis of the analytical results, the slag and bottom ash from the combustion process have been classified as non-hazardous wastes, according to the EU waste acceptance criteria (WAC), and therefore after further tests could be used in future in the construction industry. It has also been concluded that ASR bottom ash (EWC - European Waste Catalogue - code 19 01 12) could be landfilled in SNRHW (stabilized non-reactive hazardous waste) cells or used as raw material for road construction, with or without further treatment for the removal of heavy metals. In the case of fly ash from boiler or Air Pollution Control (APC) residues, it has been found that the Cd, Pb and Zn concentrations exceeded regulatory leaching test limits therefore their removal, or a stabilization process, would be essential prior to landfilling the use of these residues as construction material. Copyright © 2013 Elsevier Ltd. All rights reserved.

Development of high-level radioactive waste treatment and conversion technologies 'Dry decontamination technology development for highly radioactive contaminants'

Energy Technology Data Exchange (ETDEWEB)

Oh, Won Zin; Lee, K. W.; Won, H. J.; Jung, C. J.; Choi, W. K.; Kim, G. N.; Moon, J. K

2001-04-01

The followings were studied through the project entitled 'Dry Decontamination Technology Development for Highly Radioactive Contaminants'. 1.Contaminant Characteristics Analysis of Domestic Nuclear Fuel Cycle Projects(NFCP) and Applicability Study of the Unit Dry-Decontamination Techniques A. Classification of contaminated equipments and characteristics analysis of contaminants B. Applicability study of the unit dry-decontamination techniques 2.Performance Evaluation of Unit Dry Decontamination Technique A. PFC decontamination technique B. CO2 decontamination technique C. Plasma decontamination technique 3.Development of Residual Radiation Assessment Methodology for High Radioactive Facility Decontamination A. Development of radioactive nuclide diffusion model on highly radioactive facility structure B. Obtainment of the procedure for assessment of residual radiation dose 4.Establishment of the Design Concept of Dry Decontamination Process Equipment Applicable to Highly Radioactive Contaminants 5.TRIGA soil unit decontamination technology development A. Development of soil washing and flushing technologies B. Development of electrokinetic soil decontamination technology.

Effect of technological procedures on the crack resistance of nickel alloy welded joints under heat treatment

International Nuclear Information System (INIS)

Bagdasarov, Yu.S.; Sorokin, L.I.; Yakushin, B.F.; Moryashchev, S.F.

1983-01-01

Comparison of the efficiency of some technological procedures directed to the increase of crack resistance of KhN50MBKTYUR (EhP99) alloy welded joints under heat treatment was conducted. Welded joints were manufactured by the methods of electron beam welding, laser welding, automatic argon-arc welding. The latter was conducted by conventional technology as well as with electromagnetic mixing of liquid metal of welding bath, with compulsory cooling of weld matal, with pulse arc. It is shown that the high fracture resistance of welded joints, manufactured by electron beam and laser welding is achieved by combination of high mechanical properties of heat affected zone metal and reduced elastic potential energy margin of residual welding stresses (as compared to argon-arc welding)

Development of ecologically safety technology for steam-thermal treatment of organic wastes

Energy Technology Data Exchange (ETDEWEB)

Juravskij, J [Centre for Science, Technology and Industrial Applications, ` ` Tokema` ` , Minsk (Belarus)

1997-02-01

The experience on mitigation of the consequences of the Chernobyl`s nuclear power station accident proves that the treatment of large amounts of organic and mixed wastes containing radionuclides is a very urgent scientific and technical problem. In this connection a search for new ideas and development of highly efficient and ecologically safety technologies for treatment of organic radioactive wastes has been undertaken. This study is based on use of physico-mechanical properties of various organic materials (wood, rubber-containing composites, plastics, biomass) subjected to thermal decomposition in the overheated water steam medium. Under such conditions, there is a possibility, under relatively low temperatures (400 - 500 deg. C), to realize thermal decomposition and considerably (in 8 - 50 times) to reduce the amount of wastes, to obtain the main concentration of radionuclides in the solid residue and to prevent releases of gaseous products containing radionuclides to the environment. (author). 5 figs, 1 tab.

Soil treatment technologies combined

International Nuclear Information System (INIS)

Davis, K.J.; Russell, D.J.

1993-01-01

The Superfund Amendments and Reauthorization Act (SARA) presents a legislative mandate to select effective and long-term remediation options. SARA has spurred the development of innovative technologies and other remedial alternatives that can be applied to the diverse contaminated media at hazardous waste sites. Even though many treatment technologies have been investigated for use at hazardous waste sites, only a few have been used successfully. Soil vapor extraction and soil composting have achieved cleanup goals at sites with soils contaminated with solvents, aromatic hydrocarbons and petroleum derivatives. With the increased use of innovative on-site technologies, the integration of multiple technologies to remediate sites with complex contaminants becomes a viable and cost-effective remedial alternative. Soil vapor extraction and composting have been applied successfully as individual technologies at hazardous waste sites. An integration of these two technologies also has been used to remediate a complex contaminated site

The irradiation as alternative treatment for laboratory wastes

International Nuclear Information System (INIS)

Borrely, Sueli Ivone; Romanelli, Maria Fernanda; Silva, Giovana Pasqualini da; Castro, Daniela Marques

2005-01-01

The irradiation of effluents may be done by electron accelerator or gamma radiation source (cobalt-60). This technology has been developed as an alternative for several contaminants from different processes and sources. This paper shows the results of electron beam applied to liquid laboratories residues (effluents and standard solutions). Radiation doses were determined for the improvement of laboratories residues measured by detoxification of them. New technologies for residues treatment as well as decreasing contaminants generation is essential part of laboratories activities for environmental management for industry, universities and research institutions. (author)

Effect of Solution Properties on Arsenic Adsorption by Drinking Water Treatment Residuals

Science.gov (United States)

Nagar, R.; Sarkar, D.; Datta, R.; Sharma, S.

2005-05-01

Arsenic (As) is a ubiquitous element in the environment. Higher levels of As in soils may result from various anthropogenic sources such as use of arsenical pesticides, fertilizers, wood preservatives, smelter wastes, and coal combustion. This is of great environmental and human health concern due to the high toxicity and proven carcinogenicity of several arsenical species. Thus there is a need for developing cost effective technologies capable of lowering bioavailable As concentrations in soils to environmentally acceptable levels. In-situ immobilization of metals using inexpensive amendments such as minerals (apatite, zeolite, or clay minerals) or waste by-products (steel shot, beringite, and iron-rich biosolids) to reduce bioavailability is an inexpensive alternative to the more expensive ex-situ remediation methods. One such emerging in-situ technique is the application of drinking water treatment residuals (WTRs). WTRs can be classified as a byproduct of drinking water treatment plants and are generally composed of amorphous Fe/Al oxides, activated C and cationic polymers. WTRs possess amorphous structure and generally have high positive charge. Because As is chemically similar to phosphorus, the oxyanions As (V) and As (III) may have the potential of being retained by the WTRs. Thus, it is hypothesized that WTRs retain As irreversibly, thereby reducing As biavailability. As mobility of arsenic is controlled by adsorption reactions, knowledge of adsorption of As by WTRs is of primary relevance. Although the overall rate of adsorption is dependent on numerous factors, review of the literature indicates that competing ions in solution play an important role in the overall retention of As; however, little work has been conducted to identify which ions provide the most competition. As arsenic adsorption appears to be influenced by the variable pH-dependent charges developed on the soil particle surfaces, the effect of pH is also of critical importance. Hence, the

Advanced pyrochemical technologies for minimizing nuclear waste

International Nuclear Information System (INIS)

Bronson, M.C.; Dodson, K.E.; Riley, D.C.

1994-01-01

The Department of Energy (DOE) is seeking to reduce the size of the current nuclear weapons complex and consequently minimize operating costs. To meet this DOE objective, the national laboratories have been asked to develop advanced technologies that take uranium and plutonium, from retired weapons and prepare it for new weapons, long-term storage, and/or final disposition. Current pyrochemical processes generate residue salts and ceramic wastes that require aqueous processing to remove and recover the actinides. However, the aqueous treatment of these residues generates an estimated 100 liters of acidic transuranic (TRU) waste per kilogram of plutonium in the residue. Lawrence Livermore National Laboratory (LLNL) is developing pyrochemical techniques to eliminate, minimize, or more efficiently treat these residue streams. This paper will present technologies being developed at LLNL on advanced materials for actinide containment, reactors that minimize residues, and pyrochemical processes that remove actinides from waste salts

78 FR 66107 - National Emissions Standards for Hazardous Air Pollutants Residual Risk and Technology Review for...

Science.gov (United States)

2013-11-04

... estimate VCS voluntary consensus standards WWW world wide web Organization of this Document. The... oxidizer RTR residual risk and technology review SAB Science Advisory Board SBA Small Business... acceptable in the world in which we live'' (Risk Report at 178, quoting NRDC v. EPA, 824 F.2d 1146, 1165 (D.C...

Rebaselining of the plutonium residue elimination project at Rocky Flats Environmental Technology Site

International Nuclear Information System (INIS)

Sailor, W.C.; Catlett, D.S.; Burns, T.P.

1997-01-01

Systems Engineering and Value Engineering principles were put into practice in rebaselining the Pu Residue Stabilization and Elimination Project at the Rocky Flats Environmental Technology Site. Tradeoff studies were conducted as to how to best rebaseline the system under the new Safeguards Termination Limits (STSs) issued by the Department of Energy. Through the use of a computerized database, the means by which Stakeholder values and other high-level requirements have been included in the tradeoff studies were documented. 13 refs., 2 figs., 1 tab

Rebaselining of the plutonium residue elimination project at Rocky Flats Environmental Technology Site

Energy Technology Data Exchange (ETDEWEB)

Sailor, W.C.; Catlett, D.S.; Burns, T.P. [and others

1997-03-01

Systems Engineering and Value Engineering principles were put into practice in rebaselining the Pu Residue Stabilization and Elimination Project at the Rocky Flats Environmental Technology Site. Tradeoff studies were conducted as to how to best rebaseline the system under the new Safeguards Termination Limits (STSs) issued by the Department of Energy. Through the use of a computerized database, the means by which Stakeholder values and other high-level requirements have been included in the tradeoff studies were documented. 13 refs., 2 figs., 1 tab.

Overview of non-thermal mixed waste treatment technologies: Treatment of mixed waste (ex situ); Technologies and short descriptions

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-07-01

This compendium contains brief summaries of new and developing non- thermal treatment technologies that are candidates for treating hazardous or mixed (hazardous plus low-level radioactive) wastes. It is written to be all-encompassing, sometimes including concepts that presently constitute little more than informed ``ideas``. It bounds the universe of existing technologies being thought about or considered for application on the treatment of such wastes. This compendium is intended to be the very first step in a winnowing process to identify non-thermal treatment systems that can be fashioned into complete ``cradle-to-grave`` systems for study. The purpose of the subsequent systems paper studies is to investigate the cost and likely performance of such systems treating a representative sample of U.S. Department of Energy (DOE) mixed low level wastes (MLLW). The studies are called Integrated Non-thermal Treatment Systems (INTS) Studies and are being conducted by the Office of Science and Technology (OST) of the Environmental Management (EM) of the US Department of Energy. Similar studies on Integrated Thermal Treatment Systems have recently been published. These are not designed nor intended to be a ``downselection`` of such technologies; rather, they are simply a systems evaluation of the likely costs and performance of various non- thermal technologies that have been arranged into systems to treat sludges, organics, metals, soils, and debris prevalent in MLLW.

Overview of non-thermal mixed waste treatment technologies: Treatment of mixed waste (ex situ); Technologies and short descriptions

International Nuclear Information System (INIS)

1995-07-01

This compendium contains brief summaries of new and developing non- thermal treatment technologies that are candidates for treating hazardous or mixed (hazardous plus low-level radioactive) wastes. It is written to be all-encompassing, sometimes including concepts that presently constitute little more than informed ''ideas''. It bounds the universe of existing technologies being thought about or considered for application on the treatment of such wastes. This compendium is intended to be the very first step in a winnowing process to identify non-thermal treatment systems that can be fashioned into complete ''cradle-to-grave'' systems for study. The purpose of the subsequent systems paper studies is to investigate the cost and likely performance of such systems treating a representative sample of U.S. Department of Energy (DOE) mixed low level wastes (MLLW). The studies are called Integrated Non-thermal Treatment Systems (INTS) Studies and are being conducted by the Office of Science and Technology (OST) of the Environmental Management (EM) of the US Department of Energy. Similar studies on Integrated Thermal Treatment Systems have recently been published. These are not designed nor intended to be a ''downselection'' of such technologies; rather, they are simply a systems evaluation of the likely costs and performance of various non- thermal technologies that have been arranged into systems to treat sludges, organics, metals, soils, and debris prevalent in MLLW

Optimization of Residual Stress of High Temperature Treatment Using Genetic Algorithm and Neural Network

Directory of Open Access Journals (Sweden)

M. Susmikanti

2015-12-01

Full Text Available In a nuclear industry area, high temperature treatment of materials is a factor which requires special attention. Assessment needs to be conducted on the properties of the materials used, including the strength of the materials. The measurement of material properties under thermal processes may reflect residual stresses. The use of Genetic Algorithm (GA to determine the optimal residual stress is one way to determine the strength of a material. In residual stress modeling with several parameters, it is sometimes difficult to solve for the optimal value through analytical or numerical calculations. Here, GA is an efficient algorithm which can generate the optimal values, both minima and maxima. The purposes of this research are to obtain the optimization of variable in residual stress models using GA and to predict the center of residual stress distribution, using fuzzy neural network (FNN while the artificial neural network (ANN used for modeling. In this work a single-material 316/316L stainless steel bar is modeled. The minimal residual stresses of the material at high temperatures were obtained with GA and analytical calculations. At a temperature of 6500C, the GA optimal residual stress estimation converged at –711.3689 MPa at adistance of 0.002934 mm from center point, whereas the analytical calculation result at that temperature and position is -975.556 MPa . At a temperature of 8500C, the GA result was -969.868 MPa at 0.002757 mm from the center point, while with analytical result was -1061.13 MPa. The difference in residual stress between GA and analytical results at a temperatureof6500C is about 27 %, while at 8500C it is 8.67 %. The distribution of residual stress showed a grouping concentrated around a coordinate of (-76; 76 MPa. The residuals stress model is a degree-two polynomial with coefficients of 50.33, -76.54, and -55.2, respectively, with a standard deviation of 7.874.

Mechanical Biological Treatment

DEFF Research Database (Denmark)

Bilitewski, B-; Oros, Christiane; Christensen, Thomas Højlund

2011-01-01

The basic processes and technologies of composting and anaerobic digestion, as described in the previous chapters, are usually used for specific or source-separated organic waste flows. However, in the 1990s mechanical biological waste treatment technologies (MBT) were developed for unsorted...... or residual waste (after some recyclables removed at the source). The concept was originally to reduce the amount of waste going to landfill, but MBT technologies are today also seen as plants recovering fuel as well as material fractions. As the name suggests the technology combines mechanical treatment...... technologies (screens, sieves, magnets, etc.) with biological technologies (composting, anaerobic digestion). Two main technologies are available: Mechanical biological pretreatment (MBP), which first removes an RDF fraction and then biologically treats the remaining waste before most of it is landfilled...

Effects of thermal treatment on mineralogy and heavy metal behavior in iron oxide stabilized air pollution control residues

DEFF Research Database (Denmark)

Sørensen, Mette Abildgaard; Bender-Koch, C.; Starckpoole, M. M.

2000-01-01

Stabilization of air pollution control residues by coprecipitation with ferrous iron and subsequent thermal treatment (at 600 and 900 °C) has been examined as a means to reduce heavy metal leaching and to improve product stability. Changes in mineralogy and metal binding were analyzed using various...... analytical and environmental techniques. Ferrihydrite was formed initially but transformed upon thermal treatment to more stable and crystalline iron oxides (maghemite and hematite). For some metals leaching studies showed more substantial binding after thermal treatment, while other metals either....... Thermal treatment of the stabilized residues produced structures with an inherently better iron oxide stability. However, the concentration of metals in the leachate generally increased as a consequence of the decreased solubility of metals in the more stable iron oxide structure....

Wetland-based passive treatment systems for gold ore processing effluents containing residual cyanide, metals and nitrogen species.

Science.gov (United States)

Alvarez, R; Ordóñez, A; Loredo, J; Younger, P L

2013-10-01

Gold extraction operations generate a variety of wastes requiring responsible disposal in compliance with current environmental regulations. During recent decades, increased emphasis has been placed on effluent control and treatment, in order to avoid the threat to the environment posed by toxic constituents. In many modern gold mining and ore processing operations, cyanide species are of most immediate concern. Given that natural degradation processes are known to reduce the toxicity of cyanide over time, trials have been made at laboratory and field scales into the feasibility of using wetland-based passive systems as low-cost and environmentally friendly methods for long-term treatment of leachates from closed gold mine tailing disposal facilities. Laboratory experiments on discrete aerobic and anaerobic treatment units supported the development of design parameters for the construction of a field-scale passive system at a gold mine site in northern Spain. An in situ pilot-scale wetland treatment system was designed, constructed and monitored over a nine-month period. Overall, the results suggest that compost-based constructed wetlands are capable of detoxifying cyanidation effluents, removing about 21.6% of dissolved cyanide and 98% of Cu, as well as nitrite and nitrate. Wetland-based passive systems can therefore be considered as a viable technology for removal of residual concentrations of cyanide from leachates emanating from closed gold mine tailing disposal facilities.

Incineration and flue gas treatment technologies

International Nuclear Information System (INIS)

1997-01-01

The proceedings are presented of an international symposium on Incineration and Flue Gas Treatment Technologies, held at Sheffield University in July 1997. Papers from each of the six sessions cover the behaviour of particles in incinerator clean-up systems, pollution control technologies, the environmental performance of furnaces and incinerators, controlling nitrogen oxide emissions, separation processes during flue gas treatment and regulatory issues relating to these industrial processes. (UK)

Minimization of zirconium chlorinator residues

International Nuclear Information System (INIS)

Green, G.K.; Harbuck, D.D.

1995-01-01

Zirconium chlorinator residues contain an array of rare earths, scandium, unreacted coke, and radioactive thorium and radium. Because of the radioactivity, the residues must be disposed in special waste containment facilities. As these sites become more congested, and with stricter environmental regulations, disposal of large volumes of wastes may become more difficult. To reduce the mass of disposed material, the US Bureau of Mines (USBM) developed technology to recover rare earths, thorium and radium, and unreacted coke from these residues. This technology employs an HCl leach to solubilize over 99% of the scandium and thorium, and over 90% of the rare earths. The leach liquor is processed through several solvent extraction stages to selectively recover scandium, thorium, and rare earths. The leach residue is further leached with an organic acid to solubilize radium, thus allowing unreacted coke to be recycled to the chlorinator. The thorium and radium waste products, which comprise only 2.1% of the original residue mass, can then be sent to the radioactive waste facility

Effect of Applied Stress and Temperature on Residual Stresses Induced by Peening Surface Treatments in Alloy 600

Science.gov (United States)

Telang, A.; Gnäupel-Herold, T.; Gill, A.; Vasudevan, V. K.

2018-04-01

In this study, the effects of applied tensile stress and temperature on laser shock peening (LSP) and cavitation shotless peening (CSP)-induced compressive residual stresses were investigated using neutron and x-ray diffraction. Residual stresses on the surface, measured in situ, were lower than the applied stress in LSP- and CSP-treated Alloy 600 samples (2 mm thick). The residual stress averaged over the volume was similar to the applied stress. Compressive residual stresses on the surface and balancing tensile stresses in the interior relax differently due to hardening induced by LSP. Ex situ residual stress measurements, using XRD, show that residual stresses relaxed as the applied stress exceeded the yield strength of the LSP- and CSP-treated Alloy 600. Compressive residual stresses induced by CSP and LSP decreased by 15-25% in magnitude, respectively, on exposure to 250-450 °C for more than 500 h with 10-11% of relaxation occurring in the first few hours. Further, 80% of the compressive residual stresses induced by LSP and CSP treatments in Alloy 600 were retained even after long-term aging at 350 °C for 2400 h.

Extra heavy oil and refinery residues upgrading through Eni Slurry Technology : first EST commercial unit

Energy Technology Data Exchange (ETDEWEB)

Rispoli, G.; Sanfilippo, D.; Amoroso, A [Eni S.p.A., Rome (Italy)

2009-07-01

The production of heavy crude oils is projected to continue to grow in the upstream oil industry given that large reserves of unconventional extra heavy crude and bitumen exist in several geographic areas including Canada and Venezuela. As reserves of conventional crude oil continue to decline, these unconventional feedstocks are becoming an opportunity to pursue, but they require effective technologies for upgrading and meeting the growing demand for light and middle distillate fuels. This paper described the proprietary technology that offers a solution to upstream and downstream oil producers for bottom-of-the-barrel upgrading. En i Slurry Technology (EST) is constructing an industrial plant in its Sannazzaro refinery in Italy. The plant is designed to convert 23,000 BPSD of vacuum residue into high quality diesel and other valuable refinery streams such as liquefied petroleum gas, naphtha and jet fuel. EST is an H-addition process characterized by the use of a special homogeneous isothermal intrinsically safe reactor, and of a nano-dispersed non-ageing catalyst. EST converts more than 98 per cent of any type of residues to about 110 per cent volume of light products and distillates or extra heavy oils to high quality bottomless SCO. In typical performance, HDS is greater than 85 per cent, HDM greater than 99 per cent and HDCCR greater than 97 per cent. EST also achieves the target of zero fuel oil - zero coke. 12 refs., 4 tabs., 5 figs.

Case studies in residual use and energy conservation at wastewater treatment plants

Energy Technology Data Exchange (ETDEWEB)

Stewart, D. [Science Applications International Corp., Los Altos, CA (United States)

1995-06-01

The US Environmental Protection Agency (EPA) and the National Renewable Energy Laboratory (NREL) for the US Department of Energy (DOE) funded a study to document energy conservation activities and their effects on operation costs, regulatory compliance, and process optimization at several wastewater treatment plants (WWTPS). The purpose of this report is to review the efforts of wastewater treatment Facilities that use residuals as fuels. Case histories are presented for facilities that have taken measures to reduce energy consumption during wastewater treatment. Most of the WWTPs discussed in this report have retrofitted existing facilities to achieve energy conservation. The case studies of energy conservation measures found no effects on the facilities` ability to comply with NPDES permits. Indeed, energy conservation activities enhance environmental compliance in several ways.

Environmental Consequences of Pig Slurry Treatment Technologies

DEFF Research Database (Denmark)

ten Hoeve, Marieke

occur during manure storage and after field application. The main emissions are ammonia, nitrous oxide, methane, carbon dioxide, nitrate, phosphorus and odour. Slurry treatment technologies have been and are being developed in order to reduce the environmental impacts of manure. However, it is important...... and excluding biogenic carbon, marine and freshwater eutrophication potential, terrestrial acidification and eutrophication potential, and fossil resource depletion potential. The different types of treatment technologies showed varying environmental profiles, meaning that one type of technology was beneficial...... technology, or co-substrate for anaerobic digestion). With respect to odorous emissions, an LCIA method was developed, but due to a lack of data it proved difficult to include odour in LCA. Regulations appear to have an influence on the environmental impacts of slurry treatment. A decrease in N application...

Decision support for redesigning wastewater treatment technologies.

Science.gov (United States)

McConville, Jennifer R; Künzle, Rahel; Messmer, Ulrike; Udert, Kai M; Larsen, Tove A

2014-10-21

This paper offers a methodology for structuring the design space for innovative process engineering technology development. The methodology is exemplified in the evaluation of a wide variety of treatment technologies for source-separated domestic wastewater within the scope of the Reinvent the Toilet Challenge. It offers a methodology for narrowing down the decision-making field based on a strict interpretation of treatment objectives for undiluted urine and dry feces and macroenvironmental factors (STEEPLED analysis) which influence decision criteria. Such an evaluation identifies promising paths for technology development such as focusing on space-saving processes or the need for more innovation in low-cost, energy-efficient urine treatment methods. Critical macroenvironmental factors, such as housing density, transportation infrastructure, and climate conditions were found to affect technology decisions regarding reactor volume, weight of outputs, energy consumption, atmospheric emissions, investment cost, and net revenue. The analysis also identified a number of qualitative factors that should be carefully weighed when pursuing technology development; such as availability of O&M resources, health and safety goals, and other ethical issues. Use of this methodology allows for coevolution of innovative technology within context constraints; however, for full-scale technology choices in the field, only very mature technologies can be evaluated.

Study of treatment of a thorium and rare earths residue by extraction chromatography

International Nuclear Information System (INIS)

Zini, Josiane; Abrao, Alcidio; Carvalho, Fatima Maria Sequeira de; Freitas, Antonio Alves de; Scapin, Marcos Antonio

2005-01-01

In the 70's was established at IPEN the project of a thorium compounds purification pilot plant that had the goal of fulfilling the nuclear technology purity standards. The used method was the purification by extraction with solvents in pulsed columns. The thorium remaining in the organic phase was back extracted as thorium nitrate with a high degree of purity. Impurities, thorium non-extracted and practically all rare earths in aqueous phase of this chemical process were precipitated as hydroxide, generating a product containing thorium and rare earths, that was denominated RETOTER (residue of thorium and rare earths). This residue was accumulated and today there are 25 (twenty-five) metric tons of this by product stored in the safeguard storage shed at IPEN that must to be treated due to the radiation of the thorium and mainly his daughters. The average composition of this residue is, 68% in thorium oxide (ThO 2 ), 5% in rare earths oxides (R 2 O 3 ), 0,3% in uranium oxide (U 3 O 8 ) and common impurities such as phosphorus, iron, titanium, lead and sodium. In this work a new method is presented for separation and purification of thorium from this residue, obtaining a concentrate with high degree of purity for nuclear and non-nuclear use. This process will contribute to establish a decreasing of residue volumes, to have a mind to the minimization of environmental impacts, the reduction of worker's exposition and reduction of the storage costs. In this process the separation and purification of uranium and thorium is done by chromatography extraction, being used polymeric resins, that are previously functionalized with organic solvent (extractor agent). The effluent of this process is a concentrate of rare earths that can be reprocessed in a subsequent fractionating for to obtaining the individual fractions. (author)

Complete Treatment Versus Residual Lesion - Long-Term Evolution After Acute Coronary Syndrome

Directory of Open Access Journals (Sweden)

Alexandre de Matos Soeiro

Full Text Available Abstract Introduction: A recently published study raised doubts about the need for percutaneous treatment of nonculprit lesions in patients with acute coronary syndromes (ACS. Methods: Retrospective, unicentric, observational study. Objective: To analyze the long-term outcomes in patients undergoing treatment of the culprit artery, comparing those who remained with significant residual lesions in nonculprit arteries (group I versus those without residual lesions in other coronary artery beds (group II. The study included 580 patients (284 in group I and 296 in group II between May 2010 and May 2013. We obtained demographic and clinical data, as well as information regarding the coronary treatment administered to the patients. In the statistical analysis, the primary outcome included combined events (reinfarction/angina, death, heart failure, and need for reintervention. The comparison between groups was performed using the chi-square test and ANOVA. The long-term analysis was conducted with the Kaplan-Meier method, with a mean follow-up of 9.86 months. Results: The mean ages were 63 years in group I and 62 years in group II. On long-term follow-up, there was no significant difference in combined events in groups I and II (31.9% versus 35.6%, respectively, p = 0.76. Conclusion: The strategy of treating the culprit artery alone seems safe. In this study, no long-term differences in combined endpoints were observed between patients who remained with significant lesions compared with those without other obstructions.

The effect of heat treatment on the magnitude and composition of residual gas in sealed silica glass ampoules

Science.gov (United States)

Palosz, W.; Szofran, F. R.; Lehoczky, S. L.

1994-01-01

The residual gas pressure and composition in sealed silica glass ampoules as a function of different treatment procedures has been investigated. The dependence of the residual gas on the outgassing and annealing parameters has been determined. The effects of the fused silica brand, of the ampoule fabrication, and of post-outgassing procedures have been evaluated.

Risks of antibiotic residues in milk following intramammary and intramuscular treatments in dairy sheep.

Science.gov (United States)

Pengov, A; Kirbis, A

2009-04-01

Very few drugs on the market are approved for use in lactating ewes. Veterinarians in the European Union are allowed to prescribe drugs in an off-label manner but are then obligated to assure that residues do not enter the food chain. In case of mastitis treatment in dairy ewes antibiotic preparations designed and authorized for the bovine mammary gland are usually used. Due to inter-species differences, available bovine data cannot be accurately extrapolated for use in the dairy ewe. The objective of the study was therefore to determine appropriate withdrawal periods for ewe's milk following mastitis treatment with two commercial lactating cow products. For the detection of all components standard agar plate diffusion techniques were used. Regardless of the therapy regime and the product used, residues of antibiotics in milk were detected up to 192h after the last infusion. These results indicate that the required withholding periods for ewe's milk are considerably longer than recommended on the label for bovine milk.

Minimal Residual Disease in Acute Myeloid Leukemia

Science.gov (United States)

Hourigan, Christopher S.; Karp, Judith E.

2014-01-01

Technological advances in the laboratory have lead to substantial improvements in clinical decision-making by the use of pre-treatment prognostic risk stratification factors in acute myeloid leukemia (AML). Unfortunately similar progress has not been made in treatment response criteria, with the definition of “complete remission” in AML largely unchanged for over half a century. Several recent clinical trials have demonstrated that higher sensitivity measurements of residual disease burden during or after treatment can be performed, that results are predictive for clinical outcome and can be used to improve outcomes by guiding additional therapeutic intervention to patients in clinical complete remission but at increased relapse risk. We review here these recent trials, the characteristics and challenges of the modalities currently used to detect minimal residual disease (MRD), and outline opportunities to both refine detection and better clinically utilize MRD measurements. MRD measurement is already the standard of care in other myeloid malignancies such as chronic myelogenous leukemia (CML) and acute promyelocytic leukemia (APL). It is our belief that response criteria for non-APL AML should be updated to include assessment for molecular complete remission (mCR) and that recommendations for post-consolidation surveillance should include regular monitoring for molecular relapse as a standard of care. PMID:23799371

Incorporating regulatory considerations into waste treatment technology development

International Nuclear Information System (INIS)

Siegel, M.R.; Powell, J.A.; Williams, T.A.; Kuusinen, T.L.; Lesperance, A.M.

1991-02-01

It is generally recognized that the development of new and innovative waste treatment technologies can significantly benefit the US Department of Energy's (DOE) environmental restoration and waste management program. DOE has established a research, development, demonstration, testing, and evaluation (RDDT ampersand E) program, managed by its Office of Technology Development, to encourage and direct the development of new waste treatment and management technologies. The treatment, storage, and disposal of hazardous and radioactive waste is heavily regulated both at the federal and state levels. In order to achieve the goals of applying the best new technologies in the fastest and most cost-effective manner possible, it is essential that regulatory factors be considered early and often during the development process. This paper presents a number of regulatory issues that are relevant to any program intended to encourage the development of new waste treatment and management technologies. It will also address how the use of these basic regulatory considerations can help ensure that technologies that are developed are acceptable to regulators and can therefore be deployed in the field. 2 refs

Treatment and immobilization of intermediate level radioactive wastes

International Nuclear Information System (INIS)

Lerch, R.E.; Greenhalgh, W.O.; Partridge, J.A.; Richardson, G.L.

1977-01-01

This paper discusses a new program underway to develop and demonstrate treatment and immobilization technologies for intermediate level wastes (ILW) generated in the nuclear fuel cycle. Initial work has defined the sources, quantities and types of wastes which comprise ILW. Laboratory studies are underway to define treatment technologies for liquid ILW which contains volatile contaminants and to define immobilization parameters for the residues resulting from treatment of ILW. Immobilization agents initially being evaluated for the various residues include cement, urea-formaldehyde, and bitumen although other immobilization agents will be studied. The program also includes development of acceptable test procedures for the final immobilized products as well as development of proposed criteria for storage, transportation, and disposal of the immobilized ILW. 20 figures, 10 tables

Proceedings of emerging technologies for hazardous waste management

International Nuclear Information System (INIS)

Tedder, D.W.

1992-01-01

This book contains proceedings of emerging technologies for hazardous waste management. Topics covered include: Low-temperature oxidation of organic chemical wastes; Advanced waste minimization strategies; Treatment of manufactured gas plant (MGP) and similar wastes; Bioremediation of soils and sediments; Advances in radioactive waste treatment; Computer aides approaches to hazardous waste management; Advances in soil remediation; Low-temperature oxidation of organic chemical waste; Boremediation: Micro, meso, and macro-scale processes; In situ remediation techniques; Treatment of hazardous organics with radiation or solar energy; Technologies for management of municipal waste combustion residues; Environmental restoration and waste management; and Advanced separation and stabilization technologies

Development of the enviromental protection, development of the waste water treatment technology

Energy Technology Data Exchange (ETDEWEB)

1986-08-01

In order to establish the stable wastewater treatment technology for the coal liquefaction plant, the basic study was carried out in the fisical year 1981, 1982 and the laboratory equipment was made for the purpose of the development of the unit operation, which plays an important part of the plant and then, in the fiscal year 1983, on the basis of the results, operation studies were carried out to estimate the general quality of wastewater and the conventional treatment system in coal liquefaction plant was examined thoroughly in 1984. For purpose of the investigation on the total treatment system of coal liquefaction plant, in the current year, was carried out the analysis of water which is produced by the liquefaction reaction in It/d PDU and comparison of the values obtained from the liquefaction water samples from different coals. Moreover, to develop unit operations of effective wastewater treatment system, the following examinations were carried out; (1) phenol removal by solid-supported liquid membrance method. (2) decomposition of BOD by anaerobic fluidized bed. (3) decomposition of phenol by anaerobic bacteria. (4) removal of residual organic matters and S.S. by biofilter. (5) the total treatment system by non-biological method. Consequently many informations were obtained regarding the optimum total system. The studies finished at the fiscal year 1985. (6 tabs)

Electrodialytic upgrading of MSWI APC residue from hazardous waste to secondary resource

DEFF Research Database (Denmark)

Jensen, Pernille Erland; Kirkelund, Gunvor Marie; Parés Viader, Raimon

.g. for substitution of cement or fillers in concrete. In general leaching could not be reduced by optimizing current density and treatment time in the pilot scale stack treatment unit, as hypothesized, even though there was evidence of dependency on current density for e.g. zinc, this was not true for most elements......The aim of this project was to contribute to the development of electrodialytic treatment technology of air pollution control residues (APC) from municipal solid waste incineration (MSWI) to obtain maximal leaching reduction by optimization of treatment time and current density for different types...

A randomised controlled trial on the effect of mask choice on residual respiratory events with continuous positive airway pressure treatment.

Science.gov (United States)

Ebben, Matthew R; Narizhnaya, Mariya; Segal, Alan Z; Barone, Daniel; Krieger, Ana C

2014-06-01

It has been found that mask style can affect the amount of continuous positive airway pressure (CPAP) required to reduce an apnoea/hyponoea index (AHI) to mask style to another post titration could affect the residual AHI with CPAP. The purpose of this study was to investigate the differences in residual AHI with CPAP treatment between oronasal and nasal masks. Twenty-one subjects (age mean (M)=62.9, body mass index (BMI) M=29.6 kg/m2) were randomised (14 subjects completed the protocol) to undergo an in-laboratory CPAP titration with either a nasal mask or an oronasal mask. Subjects were then assigned this mask for 3weeks of at-home CPAP use with the optimal treatment pressure determined on the laboratory study (CPAP M=8.4 cm of H2O). At the end of this 3-week period, data were collected from the CPAP machine and the subject was given the other mask to use with the same CPAP settings for the next 3weeks at home (if the nasal mask was given initially, the oronasal one was given later and vice versa). On completion of the second 3-week period, data on residual AHI were again collected and compared with the first 3-week period on CPAP. A Wilcoxon Signed-Rank Test (two-tailed) revealed that residual AHI with CPAP treatment was significantly higher with the oronasal compared with the nasal mask (z = -3.296, pmask, and 50% of the subjects had a residual AHI >10/h in the oronasal mask condition, even though all of these subjects were titrated to an AHI of mask compared with a nasal mask. Switching to an oronasal mask post titration results in an increase in residual AHI with CPAP treatment, and pressure adjustment may be warranted. Copyright © 2014 Elsevier B.V. All rights reserved.

Investigation of effect of post weld heat treatment conditions on residual stress for ITER blanket shield blocks

Energy Technology Data Exchange (ETDEWEB)

Jung, Hun-Chea, E-mail: hcjung@nfri.re.kr [ITER Korea, National Fusion Research Institute, Daejeon (Korea, Republic of); Kim, Sa-Woong [ITER Korea, National Fusion Research Institute, Daejeon (Korea, Republic of); Lee, Yun-Hee [Division of Convergence Technology, Korea Research Institute of Standard and Science (KRISS), Daejeon (Korea, Republic of); Baek, Seung-Wook [Division of Industrial Metrology, Korea Research Institute of Standard and Science (KRISS), Daejeon (Korea, Republic of); Ha, Min-Su; Shim, Hee-Jin [ITER Korea, National Fusion Research Institute, Daejeon (Korea, Republic of)

2016-11-01

Highlights: • PWHT for ITER blanket shield block should be performed for dimensional stability. • Investigation of the effect of PWHT conditions on properties was performed. • Instrumented indentation method for evaluation of properties was used. • Residual stress and hardness decreased with increasing PWHT temperature. • Optimization of PWHT conditions would be needed for satisfaction of requirement. - Abstract: The blanket shield block (SB) shall be required the tight tolerance because SB interfaces with many components, such as flexible support keypads, First Wall (FW) support contact surfaces, FW central bolt, electrical strap contact surfaces and attachment inserts for both FW and Vacuum Vessel (VV). In order to fulfil the tight tolerance requirement, stress relieving shall be performed for dimensional stability after cover welding operation. In this paper, effect of Post Weld Heat Treatment (PWHT) conditions, temperature and holding time, was investigated on the residual stress and hardness. The 316L Stainless Steel (SS) was prepared and welded by manual TIG welding by using filler material with 2.4 mm of diameter. Welded 316L SS plate was machined to prepare the specimen for PWHT. PWHT was implemented at 250, 300, 400 °C for 2 and 3 h (400 °C only) and residual stress after relaxation were determined. The evaluation of residual stress and hardness for each specimen was carried out by instrumented indentation technique. The residual stress and hardness were decreased with increasing the heat treatment temperature and holding time.

Conceptual model and procedures to assimilate production technologies of bioenergetics of residual biomass

International Nuclear Information System (INIS)

Muto Lubota, David; González Suárez, Erenio; Hernández Pérez, Gilberto; Miño Valdés, Juan Esteban

2016-01-01

The present work expose the conceptual pattern for a process of assimilation of technologies with the purpose of creating obtaining capacities of bio energy with the objective of achieving an energy insurance of the recycle of Urban Solid Residuals (RSU) in the municipality of Cabinda, Angola. The conceptual pattern is novel because it considers the south-south collaboration, and it is supported by a general procedure of assimilation of the technologies that includes in one of its steps a specify procedure for the step concerning the insurance of the chain supply that contains as additional aspect, in a novel way, the determination of the initial’s investors capacities assisting to the demand of final products as well as to the readiness of the raw materials, based in the problems of uncertainty to the future changes. Finally conclusions are elaborated with projections for the future work. (author)

Modification of bauxite residue generated in the Bayer process by thermal treatment

International Nuclear Information System (INIS)

Garcia, M.C.S.; Pileggi, R.G.; John, V.M.; Gouvea, D.

2011-01-01

Red mud is the waste generated by the aluminum industry, and as other industrial waste presents complex characteristics with numerous difficulties in handling, as well as being a hazardous material due to its low granulometry, alkalinity and high amount generated. It is a waste with potential high polluter, aggravated by the generally adopted vulnerable disposal form, being this, the disposition of the residue in ponds designed for this purpose. The study and development of sustainable alternatives for the use of sludge, treated as raw materials from other processes, are important tendency and necessary trends in the global context of environmental preservation. This work deals with the thermal treatment as a method of modification of the characteristics of the residue, suggesting the reduction of alkalinity together with the lower leaching of alkaline ions. This approach can be a more reliable and environmentally safe disposal alternatives

Analysis of the technical capabilities of DOE sites for disposal of residuals from the treatment of mixed low-level waste

International Nuclear Information System (INIS)

Waters, R.D.; Gruebel, M.M.; Langkopf, B.S.; Kuehne, P.B.

1997-04-01

The US Department of Energy (DOE) has stored or expects to generate over the next five years more than 130,000 m 3 of mixed low-level waste (MLLW). Before disposal, MLLW is usually treated to comply with the land disposal restrictions of the Resource Conservation and Recovery Act. Depending on the type of treatment, the original volume of MLLW and the radionuclide concentrations in the waste streams may change. These changes must be taken into account in determining the necessary disposal capacity at a site. Treatment may remove the characteristic in some waste that caused it to be classified as mixed. Treatment of some waste may, by reduction of the mass, increase the concentrations of some transuranic radionuclides sufficiently so that it becomes transuranic waste. In this report, the DOE MLLW streams were analyzed to determine after-treatment volumes and radionuclide concentrations. The waste streams were reclassified as residual MLLW or low-level or transuranic waste resulting from treatment. The volume analysis indicated that about 89,000 m 3 of waste will require disposal as residual MLLW. Fifteen DOE sites were then evaluated to determine their capabilities for hosting disposal facilities for some or all of the residual MLLW. Waste streams associated with about 90% of the total residual MLLW volume are likely to present no significant issues for disposal and require little additional analysis. Future studies should focus on the remaining waste streams that are potentially problematic by examining site-specific waste acceptance criteria, alternative treatment processes, alternative waste forms for disposal, and pending changes in regulatory requirements

Residue age and tree attractiveness influence efficacy of insecticide treatments against ambrosia beetles (Coleoptera: Curculionidae)

Science.gov (United States)

Management of ambrosia beetles in ornamental nurseries relies, in part, on treatments of insecticides to prevent beetles from boring into trees emitting stress-induced ethanol. However, data on residual efficacy of commonly used pyrethroid insecticides is warranted to gauge the duration that trees ...

Soil treatment technologies: Comparison of field experiences

International Nuclear Information System (INIS)

Hodges, H.I.; Jackson, D.W.; Kline, K.

1992-01-01

A number of on-site soil treatment technologies are available for closure of oil-field waste pits, leaking underground storage tank (LUST) sites, and general hydrocarbon contamination. This paper will contrast Separation Systems Consultants, Inc.'s (SSCI's) field experiences with the following soil restoration techniques: (1) Land Treatment using indigenous microbes; (2) Land Farming using commercial microbes; (3) Low Temperature Thermal Treatment; (4) Solidification. The technologies will be contrasted in terms of regulatory constraints and requirements, key set-up and maintenance consideration, selection factors. Included in the regulatory contrast is the authors' perception of regulatory attitudes toward the techniques. Because this paper is based on actual field experience and projects, the practical aspects of making the technologies work is emphasized

Removal of copper in leachate from mining residues using electrochemical technology.

Science.gov (United States)

Lambert, Andréa; Drogui, Patrick; Daghrir, Rimeh; Zaviska, François; Benzaazoua, Mostafa

2014-01-15

This research is related to a laboratory study on the performance of a successive mining residues leaching and electrochemical copper recovery process. To clearly define the experimental region for response surface methodology (RSM), a preliminary study was performed by applying a current intensity varying from 0.5 A to 4.0 A for 60 min. By decreasing the current intensity from 4.0 A to 0.5 A, a good adhesion and a very smooth and continuous interface of copper was formed and deposited on the cathode electrode. However, the removal rate of Cu decreased from 83.7% to 37.9% when the current intensity passed from 4.0 A to 0.5 A, respectively. Subsequently, the factorial design and central composite design methodologies were successively employed to define the optimal operating conditions for copper removal in the mining residues leachate. Using a 2(3) factorial matrix, the best performance for copper removal (97.7%) was obtained at a current intensity of 2.0 A during 100 min. The current intensity and electrolysis time were found to be the most influent parameters. The contribution of current intensity and electrolysis time was around 65.8% and 33.9%, respectively. The treatment using copper electrode and current intensity of 1.3 A during 80 min was found to be the optimal conditions in terms of cost/effectiveness. Under these conditions, 86% of copper can be recovered for a total cost of 0.56 $ per cubic meter of treated mining residues leachate. Copyright © 2013 Elsevier Ltd. All rights reserved.

Quantification of heavy metals from residual waste and ashes from the treatment plant of residual water Reciclagua and,effects for the health of those workers which manipulate those residuals

International Nuclear Information System (INIS)

Guerrero D, J.J.

2004-01-01

In this work, the technique of leaching using thermostatted column in series is applied, the X-ray diffraction for the identification of the atomic and molecular structure of the toxic metals that are present in the residual muds of the water treatment plant located in the municipality of Lerma Estado de Mexico, named RECICLAGUA, likewise the technique is used of emission spectrometry for plasma and X-ray fluorescence for the qualitative analysis. Its were take samples of residual mud and of incinerated mud of the treatment plant of residual waters of the industrial corridor Toluca -Lerma RECICLAGUA, located in Lerma Estado de Mexico. For this study there were mixed 100 g of residual mud with a solution to 10% of mineral acid or sodium hydroxide according to the case, to adjust the one pH at 2, 5, 7 and 10, it was added bisulfite, of 0.3-1.5 g of dodecyl sulfate sodium and 3.939 of DTPA (triple V) (Diethylene triamine pentaacetate). To this mud and ashes were extracted the toxic and valuable metals by means of the leaching technique using thermostatted columns placed in series that were designed by the Dr. Jaime Vite Torres; it is necessary to make mention that so much the process as the equipment with those that work it was patented by the same one. With the extraction of these metals benefits are obtained, mainly of economic type, achieving the decrease of the volume of those wastes that have been generated; as well as the so much the use of those residuals, once the metals have been eliminated, as of those liquors where the metals were extracted. It was carried out a quantitative analysis using emission spectrometry by plasma in solids by this way to be able to know the content of the present metals in the sample before and later of leaching them, these results reported a great quantity of elements. Another of the techniques employees was the X-ray diffraction analysis that provides an elementary content of the samples, identifying elements that are present in

CSF inflammatory biomarkers responsive to treatment in progressive multiple sclerosis capture residual inflammation associated with axonal damage.

Science.gov (United States)

Romme Christensen, Jeppe; Komori, Mika; von Essen, Marina Rode; Ratzer, Rikke; Börnsen, Lars; Bielekova, Bibi; Sellebjerg, Finn

2018-05-01

Development of treatments for progressive multiple sclerosis (MS) is challenged by the lack of sensitive and treatment-responsive biomarkers of intrathecal inflammation. To validate the responsiveness of cerebrospinal fluid (CSF) inflammatory biomarkers to treatment with natalizumab and methylprednisolone in progressive MS and to examine the relationship between CSF inflammatory and tissue damage biomarkers. CSF samples from two open-label phase II trials of natalizumab and methylprednisolone in primary and secondary progressive MS. CSF concentrations of 20 inflammatory biomarkers and CSF biomarkers of axonal damage (neurofilament light chain (NFL)) and demyelination were analysed using electrochemiluminescent assay and enzyme-linked immunosorbent assay (ELISA). In all, 17 natalizumab- and 23 methylprednisolone-treated patients had paired CSF samples. CSF sCD27 displayed superior standardised response means and highly significant decreases during both natalizumab and methylprednisolone treatment; however, post-treatment levels remained above healthy donor reference levels. Correlation analyses of CSF inflammatory biomarkers and NFL before, during and after treatment demonstrated that CSF sCD27 consistently correlates with NFL. These findings validate CSF sCD27 as a responsive and sensitive biomarker of intrathecal inflammation in progressive MS, capturing residual inflammation after treatment. Importantly, CSF sCD27 correlates with NFL, consistent with residual inflammation after anti-inflammatory treatment being associated with axonal damage.

Plasma technology for waste treatment

International Nuclear Information System (INIS)

Cohn, D.R.

1995-01-01

Improved environmental cleanup technology is needed to meet demanding goals for remediation and treatment of future waste streams. Plasma technology has unique features which could provide advantages of reduced secondary waste, lower cost, and onsite treatment for a wide variety of applications. Plasma technology can provide highly controllable processing without the need for combustion heating. It can be used to provide high temperature processing (∼10,000 degrees C). Plasma technology can also be employed for low temperature processing (down to room temperature range) through selective plasma chemistry. A graphite electrode arc plasma furnace at MIT has been used to investigate high temperature processing of simulated solid waste for Department of Energy environmental cleanup applications. Stable, non-leachable glass has been produced. To ensure reliable operation and to meet environmental objectives, new process diagnostics have been developed to measure furnace temperature and to determine metals emissions in the gaseous effluent. Selective plasma destruction of dilute concentrations of hazardous compounds in gaseous waste streams has been investigated using electron beam generated plasmas. Selective destruction makes it possible to treat the gas steam at relatively low temperatures in the 30-300 degrees C range. On-line infrared measurements have been used in feedback operation to maximize efficiency and ensure desired performance. Plasma technology and associated process diagnostics will be used in future studies of a wide range of waste streams

Water Treatment Technology - Filtration.

Science.gov (United States)

Ross-Harrington, Melinda; Kincaid, G. David

One of twelve water treatment technology units, this student manual on filtration provides instructional materials for six competencies. (The twelve units are designed for a continuing education training course for public water supply operators.) The competencies focus on the following areas: purposes of sedimentation basins and flocculation…

The state of the art on the radioactive metal waste recycling technologies

International Nuclear Information System (INIS)

Oh, Won Jin; Moon, Jei Kwon; Jung, Chong Hun; Park, Sang Yoon

1997-09-01

As the best strategy to manage the radioactive metal wastes which are generated during operation and decommissioning of nuclear facilities, the following recycling technologies are investigated. 1. decontamination technologies for radioactive metal waste recycling 2. decontamination waste treatment technologies. 3. residual radioactivity evaluation technologies. (author). 260 refs., 26 tabs., 31 figs

Influence of post-harvest treatments with fludioxonil and soy lecithin co-application in controlling blue and grey mould and fludioxonil residues in Coscia pears.

Science.gov (United States)

Schirra, M; D'Aquino, S; Migheli, Q; Pirisi, F M; Angioni, A

2009-01-01

The residue levels of fludioxonil (FLU) were determined in Coscia pear following a 1-, 2- or 4-min dip in an aqueous mixture of FLU containing 300 or 100 mg l(-1) (active ingredient, a.i.) at 20 and 50 degrees C, respectively, with or without 2% soy lecithin. The efficacy of heat treatment with water and FLU mixtures was investigated on artificially inoculated pears for the control of post-harvest decay caused by blue (Penicillium expansum Link) and grey (Botrytis cinerea Pers. ex Fr.) mould. Treatment with 300 mg l(-1) FLU at 20 degrees C increased residues significantly when treatment time rose from 1 to 2 min; no further increase was recorded when dip time raised from 2 to 4 min. FLU residue rates were unaffected by treatment time when 300 mg l(-1) a.i. was applied in combination with lecithin at 20 degrees C. While treatment with 100 mg l(-1) a.i. at 50 degrees C for 1 and 2 min resulted in similar residue levels, significantly higher residues were detected when dip time increased from 1 to 4 min. Co-application of lecithin significantly decreased FLU residues with respect to fruit treated with FLU alone. Treatments with FLU at 20 or 50 degrees C effectively controlled decay over 10 days of incubation. While co-application of lecithin did not affect the efficacy of FLU at 300 mg l(-1)and 20 degrees C, treatment efficacy decreased when lecithin was applied in combination with 100 mg l(-1) FLU and 50 degrees C for 4 min and to a greater extent when dip time was 1-2 min.

Treatment technology for organic radioactive waste

Energy Technology Data Exchange (ETDEWEB)

Ahn, S. J.; Lee, Y. H.; Shon, J. S. [Korea Atomic Energy Research Institute, Taejon (Korea)

1999-12-01

In this report, various alternative technologies to the incineration for the treatment of radioactive organic wastes were described and reviewed, fallen into two groups of low temperature technologies and high temperature technologies. These technologies have the advantages of low volume gaseous emission, few or no dioxin generation, and operation at low enough temperature that radionuclides are not volatilized. Delphi chemical oxidation, mediated electrochemical oxidation, and photolytic ultraviolet oxidation appear to be the most promising low temperature oxidation process and steam reforming and supercritical water oxidation in the high temperature technologies. 52 refs., 39 figs., 2 tabs. (Author)

Combining mechanical-biological residual waste treatment plants with grate firing; Kombination MBA mit Rostfeuerung

Energy Technology Data Exchange (ETDEWEB)

Fleck, E. [ABB Umwelttechnik GmbH, Butzbach (Germany)

1998-09-01

The promulgation of the Technical Code on Household Waste obliges the local authorities responsible for waste disposal to review existing and prepare new waste management plans. Given the present state of the art the Code`s limit value for loss due to burning of 5% makes thermal treatment of the residual waste practically compulsory. In preparation of these developments and in order to lower costs in general and be able respond flexibly to customer demands ABB is currently undertaking great efforts to provide thermal residual waste treatment plants with a modular design. [Deutsch] Mit Veroeffentlichung der TASi wurden die entsorgungspflichtigen Gebietskoerperschaften gezwungen, bereits vorhandene Abfall-Wirtschaftsplaene zu ueberarbeiten bzw. neue zu erstellen. Technisch laeuft nach derzeitigem Wissensstand der in der TASi vorgegebene maximale Gluehverlust von 5% darauf hinaus, dass eine thermische Behandlung des Restabfalls zwingend vorgegeben ist. Um hierfuer geruestet zu sein, aber auch um generell Kosten zu senken unf flexibel auf Kundenwuensche eingehen zu koennen, unternimmt ABB grosse Abstrengungen, den Aufbau von Anlagen zur thermischen Restabfallbehandlung modular zu gestalten. (orig./SR)

Aluminum-Based Water Treatment Residue Reuse for Phosphorus Removal

Directory of Open Access Journals (Sweden)

Lai Yoke Lee

2015-04-01

Full Text Available Aluminum-based water treatment residue (Al-WTR generated during the drinking water treatment process is a readily available recycled material with high phosphorus (P adsorption capacity. The P adsorption capacity of Al-WTR generated from Singapore’s water treatment plant was evaluated with reference to particle size range, adsorption pH and temperature. Column tests, with WTR amendments in sand with and without compost, were used to simulate the bioretention systems. The adsorption rate decreased with increasing WTR sizes. Highest P adsorption capacity, 15.57 mg PO43−-P/g WTR, was achieved using fine WTR particles (>50% particles at less than 0.30 mm. At pH 4, the contact time required to reduce effluent P concentration to below the detectable range was half compared with pH 7 and 9. The adsorption rate observed at 40 ± 2 °C was 21% higher compared with that at 30 ± 2 °C. Soil mixes amended with 10% WTR and compost were able to maintain consistently high (90% total phosphorus (TP removal efficiency at a TP load up to 6.45 g/m3. In contrast, TP removal efficiencies associated with columns without WTR amendment decreased to less than 45% as the TP load increased beyond 4.5 g/m3. The results showed that WTR application is beneficial for enhanced TP removal in bioretention systems.

Expanded heat treatment to form residual compressive hoop stress on inner surface of zirconium alloy tubing

International Nuclear Information System (INIS)

Megata, Masao

1997-01-01

A specific heat treatment process that introduces hoop stress has been developed. This technique can produce zirconium alloy tubing with a residual compressive hoop stress near the inner surface by taking advantage of the mechanical anisotropy in hexagonal close-packed zirconium crystal. Since a crystal having its basal pole parallel to the tangential direction of the tubing is easier to exhibit plastic elongation under the hoop stress than that having its basal pole parallel to the radial direction, the plastic and elastic elongation can coexist under a certain set of temperature and hoop stress conditions. The mechanical anisotropy plays a role to extend the coexistent stress range. Thus, residual compressive hoop stress is formed at the inner surface where more plastic elongation occurs during the heat treatment. This process is referred to as expanded heat treatment. Since this is a fundamental crystallographic principle, it has various applications. The application to improve PCI/SCC (pellet cladding interaction/stress corrosion cracking) properties of water reactor fuel cladding is promising. Excellent results were obtained with laboratory-scale heat treatment and an out-reactor iodine SCC test. These results included an extension of the time to SCC failure. (author)

Water Treatment Technology - Wells.

Science.gov (United States)

Ross-Harrington, Melinda; Kincaid, G. David

One of twelve water treatment technology units, this student manual on wells provides instructional materials for five competencies. (The twelve units are designed for a continuing education training course for public water supply operators.) The competencies focus on the following areas: dug, driven, and chilled wells, aquifer types, deep well…

Water Treatment Technology - Hydraulics.

Science.gov (United States)

Ross-Harrington, Melinda; Kincaid, G. David

One of twelve water treatment technology units, this student manual on hydraulics provides instructional materials for three competencies. (The twelve units are designed for a continuing education training course for public water supply operators.) The competencies focus on the following areas: head loss in pipes in series, function loss in…

Drying of residue and separation of nitrate salts in the sludge waste for the lagoon sludge treatment

International Nuclear Information System (INIS)

Hwang, D. S.; Lee, K. I.; Choi, Y. D.; Hwang, S. T.; Park, J. H.

2003-01-01

This study investigated the dissolution property of nitrate salts in the dissolution process by water and the drying property of residue after separating nitrates in a series of the processes for the sludge treatment. Desalination was carried out with the adding ratio of water and drying property was analyzed by TG/DTA, FTIR, and XRD. Nitrate salts involved in the sludge were separated over 97% at the water adding ratio of 2.5. But a small quantity of calcium and sodium nitrate remained in the residue These were decomposed over 600 .deg. C and calcium carbonate, which was consisted mainly of residue, was decomposed into calcium oxide over 750 .deg. C. The residue have to be decomposed over 800 .deg. C to converse uranyl nitrate of six value into the stable U 3 O 8 of four value. As a result of removing the nitrates at the water adding ratio of 2.5 and drying the residue over 900 .deg. C, volume of the sludge waste decreased over 80%

Novel treatment technologies for PFAS compounds: A critical review.

Science.gov (United States)

Kucharzyk, Katarzyna H; Darlington, Ramona; Benotti, Mark; Deeb, Rula; Hawley, Elisabeth

2017-12-15

Perfluorinated compounds such as perfluorooctane sulfonate (PFOS) and perfluorooctanoic acid (PFOA) have recently drawn great attention due to their wide distribution in aquatic environments. The understanding of the physicochemical properties and fate and transport of PFAs in groundwater is still limited. Preliminary studies indicate that these compounds can readily bioaccumulate and pose human and animal health concerns. Due to their physicochemical properties, PFOS and PFOA are water soluble, nonvolatile and persistent in the environment, which is a cause of concern related to their treatment with conventional remediation technologies. Extraction with inefficient carbon adsorption is one of the most common treatment technologies for remediation of PFOS- or PFOA-impacted groundwater. Several other innovative and promising technologies, including sonochemistry, bioremediation and photolysis, have been tested for their effectiveness in removal of perfluorinated compounds. This paper provides a baseline for understanding research needs to better develop treatment technologies for PFOA and PFOS in groundwater. Frontiers for improving the state of practice for PFOA and PFOS treatment include the development of more cost-effective ex situ treatment methods and the development and demonstration of promising in situ treatment technologies at the pilot and full scale. Copyright © 2017 Elsevier Ltd. All rights reserved.

The treatment of residual stress in fracture assessment of pressure vessels

International Nuclear Information System (INIS)

Green, D.; Knowles, J.

1992-01-01

The treatment of weld residual stress in the fracture assessment of cylindrical pressure vessels is considered through partitioning the stress into membrane, bending and self-balancing through wall components. The influence of each on fracture behavior is discussed. Stress intensity factor solutions appropriate to each type of stress are presented. Short range, medium range and long range stress categories are identified according to simple rules relating the effect of increasing crack length to stress intensity factor and ligament net stress. Proposals are made on how the stress intensity factor from these stress types may be incorporated into a Kr, Lr based fracture assessment

Leveraging technology to enhance addiction treatment and recovery.

Science.gov (United States)

Marsch, Lisa A

2012-01-01

Technology such as the Internet and mobile phones offers considerable promise for affecting the assessment, prevention, and treatment of and recovery from substance use disorders. Technology may enable entirely new models of behavioral health care within and outside of formal systems of care. This article reviews the promise of technology-based therapeutic tools for affecting the quality and reach of addiction treatment and recovery support systems, as well as the empirical support to date for this approach. Potential models for implementing technology-based interventions targeting substance use disorders are described. Opportunities to optimize the effectiveness and impact of technology-based interventions targeting addiction and recovery, along with outstanding research needs, are discussed.

Thermal Treatment of Iron Oxide Stabilized APC Residues from Waste Incineration and the Effect on Heavy Metal Binding

DEFF Research Database (Denmark)

Sørensen, Mette Abildgaard; Stackpoole, M.; Bender-Koch, C.

2000-01-01

Iron oxide stabilized APC residues from MSWI were heat treated at 600°C and 900°C. The thermal treatments resulted in a change in product stability by forcing a transformation in the mineralogical structures of the products. The treatments, moreover, simulated somewhat the natural aging processes...

Incineration technologies

CERN Document Server

Buekens, Alfons

2013-01-01

Waste incineration is the art of completely combusting waste, while maintaining or reducing emission levels below current emission standards. Where possible, objectives include the recovering of energy as well as the  combustion residues.  Successful waste incineration makes it possible to achieve a deep reduction in waste volume, obtain a compact and sterile residue, and eliminate a wide array of pollutants. This book places waste incineration within the wider context of waste management, and demonstrates that, in contrast to landfills and composting, waste incineration can eliminate objectionable and hazardous properties such as flammability and toxicity, result in a significant reduction in volume, and destroy gaseous and liquid waste streams leaving little or no residues beyond those linked to flue gas neutralization and treatment. Moreover, waste incineration sterilizes and destroys putrescible matter, and produces usable heat.  Incineration Technologies first appeared as a peer-reviewed contribution ...

The LOMOsup(R) process: a solution for residual monomers

International Nuclear Information System (INIS)

Derbyshire, R.L.

1979-01-01

Regulatory activity over the last several years has addressed the potential problems associated with the migration of residual monomers from a number of commodity food packages. Regardless of the outcome of current debates, it will always be desirable to reduce monomer levels to as low a level as economically practicable so that they do not become indirect additives. The LOMO process is a body of technology inclusive of an ionizing radiation treatment which can result in sharp reduction of residual monomer levels in commodity plastic resins. The process may be applicable to factory intermediates, raw resins, or finished articles. Depending upon the individual system and its monomers, LOMO treatment can result in reductions to levels which press today's analytical test capability. Industrial radiation processing is normally accomplished with electron beam accelerators. Electron beam processing continues to gain in understanding and acceptance as one of the very few basic methods by which energy can be imparted to an industrial process system. Typically, whole factories are constructed around one accelerator. (author)

Sustainability assessment of advanced wastewater treatment technologies

DEFF Research Database (Denmark)

Høibye, Linda; Clauson-Kaas, Jes; Wenzel, Henrik

2007-01-01

, which includes technical, economic and environmental aspects. The technical and economic assessment is performed on 5 advanced treatment technologies: sand filtration, ozone treatment, UV exclusively for disinfection of pathogenic microorganisms, Membrane Bioreactor (MBR), and UV in combination......As a consequence of the EU Water Framwork Directive, more focus is now on discharges of hazardous substances from wastewater treatment plants and sewers. Thus, many municipalities in Denmark may have to adopt to future advenced treatment technologies. This paper describes a holistic assessment...... with advanced oxidation. The technical assessment is based on 12 hazardous substances comprising heavy metals, organic pollutants, endocrine disruptors as well as pathogenic microorganisms. The environmental assessment is performed by life cycle assessment (LCA) comprising 9 of the specific hazardous substances...

Sustainability assessment of advanced wastewater treatment technologies

DEFF Research Database (Denmark)

Høibye, Linda; Clauson-Kaas, Jes; Wenzel, Henrik

2008-01-01

, which includes technical, economical and environmental aspects. The technical and economical assessment is performed on 5 advanced treatment technologies: sand filtration, ozone treatment, UV exclusively for disinfection of pathogenic microorganisms, membrane bioreactor (MBR) and UV in combination......As a consequence of the EU Water Framework Directive more focus is now on discharges of hazardous substances from wastewater treatment plants and sewers. Thus, many municipalities in Denmark may have to adopt to future advanced treatment technologies. This paper describes a holistic assessment...... with advanced oxidation. The technical assessment is based on 12 hazardous substances comprising heavy metals, organic pollutants, endocrine disruptors as well as pathogenic microorganisms. The environmental assessment is performed by life cycle assessment (LCA) comprising 9 of the specific hazardous substances...

Investigation on reusing water treatment residuals to remedy soil contaminated with multiple metals in Baiyin, China

International Nuclear Information System (INIS)

Wang, Changhui; Zhao, Yuanyuan; Pei, Yuansheng

2012-01-01

Highlights: ► Fe/Al water treatment residuals (FARs) can stabilize As, Pb, Ni, Zn, Cr and Cu. ► FARs cannot stabilize Ba and Cd. ► The properties of FARs and soil affect the FARs’ ability of stabilizing metals. - Abstract: In this work, the remediation of soils contaminated with multiple metals using ferric and alum water treatment residuals (FARs) in Baiyin, China, was investigated. The results of metals fractionation indicated that after the soil was treated with FARs, arsenic (As), lead (Pb), nickel (Ni), zinc (Zn) and copper (Cu) could be transformed into more stable forms, i.e., As bound in crystalline Fe/Al oxides and other metals in the oxidable and residual forms. However, the forms of chromium (Cr) and cadmium (Cd) were unaffected. Interestingly, due to the effect of FARs, barium (Ba) was predominantly transformed into more mobile forms. The bioaccessibility extraction test demonstrated that the FARs reduced the bioaccessibility of As by 25%, followed by Cu, Cr, Zn, Ni and Pb. The bioaccessibility of Cd and Ba were increased; in particular, there was an increase of 41% for Ba at the end of the test. In conclusion, the FARs can be used to remedy soil contaminated with multiple metals, but comprehensive studies are needed before practical applications of this work.

High-yield pulping effluent treatment technologies

International Nuclear Information System (INIS)

Su, W.X.; Hsieh, J.S.

1993-03-01

The objective of this report is to examine the high-yield (mechanical) pulp processes with respect to environmental issues affected by the discharge of their waste streams. Various statistics are given that support the view that high-yield pulping processes will have major growth in the US regions where pulp mills are located, and sites for projects in the development phase are indicated. Conventional and innovative effluent-treatment technologies applicable to these processes are reviewed. The different types of mechanical pulping or high-yield processes are explained, and the chemical additives are discussed. The important relationship between pulp yield and measure of BOD in the effluent is graphically presented. Effluent contaminants are identified, along with other important characteristics of the streams. Current and proposed environmental limitations specifically related to mechanical pulp production are reviewed. Conventional and innovative effluent-treatment technologies are discussed, along with their principle applications, uses, advantages, and disadvantages. Sludge management and disposal techniques become an intimate part of the treatment of waste streams. The conclusion is made that conventional technologies can successfully treat effluent streams under current waste-water discharge limitations, but these systems may not be adequate when stricter standards are imposed. At present, the most important issue in the treatment of pulp-mill waste is the management and disposal of the resultant sludge

Assessment of residual error for online cone-beam CT-guided treatment of prostate cancer patients

International Nuclear Information System (INIS)

Letourneau, Daniel; Martinez, Alvaro A.; Lockman, David; Yan Di; Vargas, Carlos; Ivaldi, Giovanni; Wong, John

2005-01-01

Purpose: Kilovoltage cone-beam CT (CBCT) implemented on board a medical accelerator is available for image-guidance applications in our clinic. The objective of this work was to assess the magnitude and stability of the residual setup error associated with CBCT online-guided prostate cancer patient setup. Residual error pertains to the uncertainty in image registration, the limited mechanical accuracy, and the intrafraction motion during imaging and treatment. Methods and Materials: The residual error for CBCT online-guided correction was first determined in a phantom study. After online correction, the phantom residual error was determined by comparing megavoltage portal images acquired every 90 deg. to the corresponding digitally reconstructed radiographs. In the clinical study, 8 prostate cancer patients were implanted with three radiopaque markers made of high-winding coils. After positioning the patient using the skin marks, a CBCT scan was acquired and the setup error determined by fusing the coils on the CBCT and planning CT scans. The patient setup was then corrected by moving the couch accordingly. A second CBCT scan was acquired immediately after the correction to evaluate the residual target setup error. Intrafraction motion was evaluated by tracking the coils and the bony landmarks on kilovoltage radiographs acquired every 30 s between the two CBCT scans. Corrections based on soft-tissue registration were evaluated offline by aligning the prostate contours defined on both planning CT and CBCT images. Results: For ideal rigid phantoms, CBCT image-guided treatment can usually achieve setup accuracy of 1 mm or better. For the patients, after CBCT correction, the target setup error was reduced in almost all cases and was generally within ±1.5 mm. The image guidance process took 23-35 min, dictated by the computer speed and network configuration. The contribution of the intrafraction motion to the residual setup error was small, with a standard deviation of

High level compressive residual stresses produced in aluminum alloys by laser shock processing

International Nuclear Information System (INIS)

Gomez-Rosas, G.; Rubio-Gonzalez, C.; Ocana, J.L; Molpeceres, C.; Porro, J.A.; Chi-Moreno, W.; Morales, M.

2005-01-01

Laser shock processing (LSP) has been proposed as a competitive alternative technology to classical treatments for improving fatigue and wear resistance of metals. We present a configuration and results for metal surface treatments in underwater laser irradiation at 1064 nm. A convergent lens is used to deliver 1.2 J/cm 2 in a 8 ns laser FWHM pulse produced by 10 Hz Q-switched Nd:YAG, two laser spot diameters were used: 0.8 and 1.5 mm. Results using pulse densities of 2500 pulses/cm 2 in 6061-T6 aluminum samples and 5000 pulses/cm 2 in 2024 aluminum samples are presented. High level of compressive residual stresses are produced -1600 MPa for 6061-T6 Al alloy, and -1400 MPa for 2024 Al alloy. It has been shown that surface residual stress level is higher than that achieved by conventional shot peening and with greater depths. This method can be applied to surface treatment of final metal products

Technology and the Future of Mental Health Treatment

Science.gov (United States)

... Health Intervention Technology? Join a Study Learn More Technology and the Future of Mental Health Treatment Introduction ... What is NIMH’s Role in Mental Health Intervention Technology? Between FY2009 and FY2015, NIMH awarded 404 grants ...

Energy generation for sustainable development with innovation technology and utilization of biomass residue; Geracao de energia para o desenvolvimento rural sustentavel com inovacao tecnologica de aproveitamento de biomassa residual

Energy Technology Data Exchange (ETDEWEB)

Fernandes, Maria Roseane de Pontes; Lopes, Carlos Eduardo Bezerra; Costa Neto, Manoel Bezerra da; Selvam, P.V. Pannir [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil)

2004-07-01

In the present work, the introduction of alternative energy of biogas in agricultural communities for the sustainable development was studied through exploitation of residual biomass and also getting as by-product the biological fertilizer. A fast composting of the domestic residue with the organic was made possible where part of this residue after processing was taken together with effluent to the biodigestor. The bibliographical research on the processes of generation of biogas, about composting and the equipment for processing had been carried through. The projects Engineering with the use of computational tools had been developed with the Software Super Pro 4,9 Design and ORC GPEC 2004 by our research group. Five case studies had been elaborated, where different scenes related with our innovation, that uses of the residue for the composting together with domestic effluent for digestion. Several economic parameters were obtained and our work proved the viability about the use of biogas for drying of the fruits banana. A economic feasibility study was carried where it was proven that the project with the innovation of the use of residues from the fruits possesses more advantages than the conventional system of drying using electric energy. Considering the viability of this process and the use solar energy, it is intended to apply this technology in rural agricultural communities providing them an energy source of low cost in substitution of the conventional energy. (author)

Characterization and analyses on micro-hardness, residual stress and microstructure in laser cladding coating of 316L stainless steel subjected to massive LSP treatment

Energy Technology Data Exchange (ETDEWEB)

Luo, K.Y.; Jing, X.; Sheng, J. [School of Mechanical Engineering, Jiangsu University, Zhenjiang, 212013 (China); Sun, G.F. [School of Mechanical Engineering, Southeast University, Nanjing, 211189 (China); Yan, Z. [School of Mechanical Engineering, Jiangsu University, Zhenjiang, 212013 (China); Lu, J.Z., E-mail: jzlu@ujs.edu.cn [School of Mechanical Engineering, Jiangsu University, Zhenjiang, 212013 (China)

2016-07-15

The effects of massive laser shock peening (LSP) treatment on micro-hardness, residual stress and microstructure in four different zones of laser cladding coating was investigated. Furthermore, micro-hardness curves and residual stress distributions with and without massive LSP treatment were presented and compared, and typical microstructure in different zones of both coatings were characterized by transmission electron microscope (TEM) and cross-sectional optical microscope (OM) observations. Results and analyses showed that massive LSP treatment had an important influence on micro-hardness and residual stress of the cladding coating. Special attempt was made to the effects of massive LSP treatment on microstructure in three zones of the cladding coating. In addition, the underlying mechanism of massive LSP treatment on microstructure and mechanical properties of the cladding coating was revealed clearly. - Highlights: • Micro-hardness and residual stress curves of both coatings were presented and compared. • Typical microstructure in different zones of both coatings were characterized and analyzed. • LSP causes increased micro-activities, and induces plastic deformation layer in three zones. • Underlying mechanism of LSP on mechanical properties of cladding coating was revealed.

Comprehensive reuse of drinking water treatment residuals in coagulation and adsorption processes.

Science.gov (United States)

Jung, Kyung-Won; Hwang, Min-Jin; Park, Dae-Seon; Ahn, Kyu-Hong

2016-10-01

While drinking water treatment residuals (DWTRs) inevitably lead to serious problems due to their huge amount of generation and limitation of landfill sites, their unique properties of containing Al or Fe contents make it possible to reuse them as a beneficial material for coagulant recovery and adsorbent. Hence, in the present study, to comprehensively handle and recycle DWTRs, coagulant recovery from DWTRs and reuse of coagulant recovered residuals (CRs) were investigated. In the first step, coagulant recovery from DWTRs was conducted using response surface methodology (RSM) for statistical optimization of independent variables (pH, solid content, and reaction time) on response variable (Al recovery). As a result, a highly acceptable Al recovery of 97.5 ± 0.4% was recorded, which corresponds to 99.5% of the predicted Al recovery. Comparison study of recovered and commercial coagulant from textile wastewater treatment indicated that recovered coagulant has reasonable potential for use in wastewater treatment, in which the performance efficiencies were 68.5 ± 2.1% COD, 97.2 ± 1.9% turbidity, and 64.3 ± 1.0% color removals at 50 mg Al/L. Subsequently, in a similar manner, RSM was also applied to optimize coagulation conditions (Al dosage, initial pH, and reaction time) for the maximization of real cotton textile wastewater treatment in terms of COD, turbidity, and color removal. Overall performance revealed that the initial pH had a remarkable effect on the removal performance compared to the effects of other independent variables. This is mainly due to the transformation of metal species form with increasing or decreasing pH conditions. Finally, a feasibility test of CRs as adsorbent for phosphate adsorption from aqueous solution was conducted. Adsorption equilibrium of phosphate at different temperatures (10-30 °C) and initial levels of pH (3-11) indicated that the main mechanisms of phosphate adsorption onto CRs are endothermic and chemical

Treatment of mine water and solid residues (RS) in San Rafael mining and milling complex

International Nuclear Information System (INIS)

Asenjo, Armando R.; Perrino, Juan F.

2006-01-01

San Rafael Mining and Milling Complex is located in Mendoza Province, in San Rafael Department, 38 km West from San Rafael city and 240 km south from Mendoza city, capital of the province. Activities related with yellow cake production were performed from 1979 to 1999. Nowadays the mine and the plant are in stand by. At the moment technical, economic and environmental studies are being done in order to restart the activities. Different kind of residues are accumulated in the site: a) Tailing; b) Sludges; c) Low grade ores; e) Waste rock; f) Mine water; g) Solid residues (RS). In this paper methodology to treat mine water and solid residues (RS) will be informed. a) Mine water: 800.000 m 3 of mine water are accumulated in different open pit. Uranium, radium and arsenic are the main ions to take into account to treat the water. Several laboratory and pilot test have been performed in order to define the treatment of the water, according with the regulatory requirement. A methodology using anion exchange resin to fix uranium and precipitation using barium chloride and iron sulfate to separate radium and arsenic has been developed. b) Solid residues (RS): these residues (precipitates) have been produced by neutralization of effluents in a nuclear purification process (TBP process). They are accumulated in drums. These residues come from Cordoba plant, a factory which produces UO 2 powder. The total content of uranium in the precipitate is 14.249 kg with an average uranium concentration of 1,33%. A methodology using sulfuric acid dissolution of the precipitates and anion exchange resin to recovery the uranium has been developed. (author) [es

Plasma technology for treatment of waste

Energy Technology Data Exchange (ETDEWEB)

Cohn, D [Massachusetts Inst. of Technology, Cambridge, MA (United States). Plasma Fusion Center

1997-12-31

Meeting goals for waste cleanup will require new technology with improved environmental attractiveness and reduced cost. Plasma technology appears promising because of the high degree of controllability; capability to process waste without the adverse effects of combustion; and a very wide temperature range of operation. At the Plasma Fusion Center at the Massachusetts Institute of Technology, a range of plasma technologies are being investigated. `Hot` thermal plasmas produced by DC arc technology are being examined for treatment of solid waste. In conjunction with this activity, new diagnostics are being developed for monitoring arc furnace operating parameters and gaseous emissions. Electron-beam generated plasma technology is being investigated as a means of producing non-thermal `cold` plasmas for selective processing of dilute concentrations of gaseous waste. (author). 4 figs., 5 refs.

Greenhouse gas reductions through enhanced use of residues in the life cycle of Malaysian palm oil derived biodiesel

DEFF Research Database (Denmark)

Hansen, Sune Balle; Olsen, Stig Irving; Ujang, Zaini

2012-01-01

This study identifies the potential greenhouse gas (GHG) reductions, which can be achieved by optimizing the use of residues in the life cycle of palm oil derived biodiesel. This is done through compilation of data on existing and prospective treatment technologies as well as practical experiments...... extraction from empty fruit bunches was found to be the most significant in the biodiesel production life cycle. All the studied waste treatment technologies performed significantly better than the conventional practices and with dedicated efforts of optimized use in the palm oil industry, the production...

Control of postharvest diseases of fruit by heat and fungicides: efficacy, residue levels, and residue persistence. A review.

Science.gov (United States)

Schirra, Mario; D'Aquino, Salvatore; Cabras, Paolo; Angioni, Alberto

2011-08-24

Extensive research has been done in recent years to reduce the heavy dependence on chemical fungicides to control postharvest diseases and disorders of horticultural crops. Alternative strategies were based on improved cultural practices, biological control, plant-defense promoters, and physical treatments such as UV illumination, radiofrequency treatment, heat therapy, and storage technologies. Among these, postharvest heat treatments such as hot water dips, short hot water rinsing and brushing, and hot air conditioning have reduced rot development and enhanced fruit resistance to chilling injury in sensitive cultivars while retaining fruit quality during cold storage and shelf life. Additive or synergistic increases in effectiveness were observed by integrating heat therapy with various chemical compounds, thus leading to significant reductions in the application of active ingredients to protect produce from decay. This paper highlights the knowledge on this topic with emphasis on heat therapy effects and factors affecting the uptake, persistence, and performance of fungicide residues when they are applied in combination with hot water.

The Impact of Advanced Technologies on Treatment Deviations in Radiation Treatment Delivery

International Nuclear Information System (INIS)

Marks, Lawrence B.; Light, Kim L.; Hubbs, Jessica L.; Georgas, Debra L.; Jones, Ellen L.; Wright, Melanie C.; Willett, Christopher G.; Yin Fangfang

2007-01-01

Purpose: To assess the impact of new technologies on deviation rates in radiation therapy (RT). Methods and Materials: Treatment delivery deviations in RT were prospectively monitored during a time of technology upgrade. In January 2003, our department had three accelerators, none with 'modern' technologies (e.g., without multileaf collimators [MLC]). In 2003 to 2004, we upgraded to five new accelerators, four with MLC, and associated advanced capabilities. The deviation rates among patients treated on 'high-technology' versus 'low-technology' machines (defined as those with vs. without MLC) were compared over time using the two-tailed Fisher's exact test. Results: In 2003, there was no significant difference between the deviation rate in the 'high-technology' versus 'low-technology' groups (0.16% vs. 0.11%, p = 0.45). In 2005 to 2006, the deviation rate for the 'high-technology' groups was lower than the 'low-technology' (0.083% vs. 0.21%, p = 0.009). This difference was caused by a decline in deviations on the 'high-technology' machines over time (p = 0.053), as well as an unexpected trend toward an increase in deviations over time on the 'low-technology' machines (p = 0.15). Conclusions: Advances in RT delivery systems appear to reduce the rate of treatment deviations. Deviation rates on 'high-technology' machines with MLC decline over time, suggesting a learning curve after the introduction of new technologies. Associated with the adoption of 'high-technology' was an unexpected increase in the deviation rate with 'low-technology' approaches, which may reflect an over-reliance on tools inherent to 'high-technology' machines. With the introduction of new technologies, continued diligence is needed to ensure that staff remain proficient with 'low-technology' approaches

Residual symptoms and functioning in depression, does the type of residual symptom matter? A post-hoc analysis

Directory of Open Access Journals (Sweden)

Romera Irene

2013-02-01

Full Text Available Abstract Background The degrees to which residual symptoms in major depressive disorder (MDD adversely affect patient functioning is not known. This post-hoc analysis explored the association between different residual symptoms and patient functioning. Methods Patients with MDD who responded (≥50% on the 17-item Hamilton Rating Scale for Depression; HAMD-17 after 3 months of treatment (624/930 were included. Residual core mood-symptoms (HAMD-17 core symptom subscale ≥1, residual insomnia-symptoms (HAMD-17 sleep subscale ≥1, residual anxiety-symptoms (HAMD-17-anxiety subscale ≥1, residual somatic-symptoms (HAMD-17 Item 13 ≥1, pain (Visual Analogue Scale ≥30, and functioning were assessed after 3 months treatment. A stepwise logistic regression model with normal functioning (Social and Occupational Functioning Assessment Scale ≥80 as the dependent variable was used. Results After 3 months, 59.5% of patients (371/624 achieved normal functioning and 66.0% (412/624 were in remission. Residual symptom prevalence was: core mood symptoms 72%; insomnia 63%; anxiety 78%; and somatic symptoms 41%. Pain reported in 18%. Factors associated with normal functioning were absence of core mood symptoms (odds ratio [OR] 8.7; 95% confidence interval [CI], 4.6–16.7, absence of insomnia symptoms (OR 1.8; 95% CI, 1.2–2.7, episode length (4–24 weeks vs. ≥24 weeks [OR 2.0; 95% CI, 1.1–3.6] and better baseline functioning (OR 1.0; 95% CI, 1.0–1.1. A significant interaction between residual anxiety symptoms and pain was found (p = 0.0080. Conclusions Different residual symptoms are associated to different degrees with patient functioning. To achieve normal functioning, specific residual symptoms domains might be targeted for treatment.

TECHNOLOGICAL TESTS USING QUARTZITE RESIDUES AS COMPONENT OF CERAMIC MASS AT THE PORCELAIN STONEWARE PRODUCTION

Directory of Open Access Journals (Sweden)

Marcondes Mendes Souza

2015-03-01

Full Text Available This work aims to evaluate through technological tests the use of quartzite residues as component at the the production of porcelain stoneware. Were collected five samples of quartzites called of green quartzite, black quartzite, pink quartzite, goldy quartzite, white quartzite. After, the raw materials were milled, passed by a sieve with a Mesh of 200# (Mesh and characterized by chemical analysis in fluorescence of x-rays and also analysis of the crystalline phases by diffraction of x-rays. The porcelain tiles mass is composed of five formulations containing 57% of feldspar, 37% of clay and 6% of residues of quartzite with different coloration. For the preparation of the specimens, it was used uniaxial pressing, which afterwards were synthesized at 1150°C, 1200°C and 1250°C. After the sintering, the specimens were submit for tests of technological characterization like: water absorption, linear shrinkage, apparently porosity, density and flexural strain at three points. The results presented in the fluorescence of x-rays showed a high-content of iron oxide on black quartzite that is why it was discarded the utilization of it in porcelain stoneware. All quartzite formulations had low water absorption achieved when synthesized at 1200°C, getting 0.1 to 0.36% without having gone through the atomization process. At the tests of flexural strain, all the quartzite had in acceptance limits, according to the European norm EN 100, overcoming 27 MPA at 1200°C

Assays of residual antibiotics after treatment of γ-ray and UV irradiation

International Nuclear Information System (INIS)

Shin, Ji Hye; Nam, Ji Hyun; Lee, Dong Hun; Yu, Seung Ho; Lee, Myun Joo

2010-01-01

The pollution of antibiotics is a major cause of spreading antibiotics resistant bacteria in the environment. Applications of ozonation, UV, and γ-ray irradiations have been introduced to remove antibiotics in the effluents from wastewater treatment system. In this study, we compared the chemical (HPLC) and biological (antimicrobial susceptibility test, AMS) assays in measuring of the concentrations of residual antibiotics after γ-ray and UV irradiation. Most samples were degraded by γ-ray irradiation (1 ∼ 2 kGy). However, lincomycin and tetracycline were not degraded by UV irradiation. The concentration of residual antibiotics, that was treated with γ-ray and UV irradiation, measuring by bioassay was similar to HPLC. The concentrations of γ-ray irradiated cephradine measured by AMS test were 2 times higher than of HPLC assay, indicating AMS test is more sensitive than HPLC assay. These results indicate that γ-ray irradiation technique is more useful than UV irradiation, and biological assay is more useful to detect the antibiotics and toxic intermediates in antibiotics degradation

Socioeconomic constraints on the technological choices in rural sewage treatment.

Science.gov (United States)

Gu, Baojing; Fan, Liangcong; Ying, Zechun; Xu, Qingshan; Luo, Weidong; Ge, Ying; Scott, Steffanie; Chang, Jie

2016-10-01

Technological innovation is one of the potential engines to mitigate environmental pollution. However, the implementation of new technologies sometimes fails owing to socioeconomic constraints from different stakeholders. Thus, it is essential to analyze constraints of environmental technologies in order to build a pathway for their implementation. In this study, taking three technologies on rural sewage treatment in Hangzhou, China as a case study, i.e., wastewater treatment plant (WTP), constructed wetland (CW), and biogas system, we analyzed how socioeconomic constraints affect the technological choices. Results showed that socioeconomic constraints play a key role through changing the relative opportunity cost of inputs from government as compared to that of residents to deliver the public good-sewage treatment-under different economic levels. Economic level determines the technological choice, and the preferred sewage treatment technologies change from biogas system to CW and further to WTP along with the increase of economic level. Mismatch of technological choice and economic level results in failures of rural sewage treatment, e.g., the CW only work well in moderately developed regions in Hangzhou. This finding expands the environmental Kuznets law by introducing the coproduction theory into analysis (i.e., inputs from both government and residents are essential for the delivery of public goods and services such as good environmental quality). A match between technology and socioeconomic conditions is essential to the environmental governance.

Disruptive technology in the treatment of thoracic trauma.

Science.gov (United States)

Smith, R Stephen

2013-12-01

The care of patients with thoracic injuries has undergone monumental change over the past 25 years. Advances in technology have driven improvements in care, with obvious benefits to patients. In many instances, new or "disruptive" technologies have unexpectedly displaced previously established standards for the diagnosis and treatment of these potentially devastating injuries. Examples of disruptive technology include the use of ultrasound technology for the diagnosis of cardiac tamponade and pneumothorax; thoracoscopic techniques instead of thoracotomy, pulmonary tractotomy, and stapled lung resection; endovascular repair of thoracic aortic injury; operative fixation of flail chest; and the enhanced availability of extracorporeal lung support for severe respiratory failure. Surgeons must be prepared to recognize the benefits, and limits, of novel technologies and incorporate these methods into day-to-day treatment protocols. Copyright © 2013 Elsevier Inc. All rights reserved.

Mixed Waste Integrated Program interim evaluation report on thermal treatment technologies

International Nuclear Information System (INIS)

Gillins, R.L.; DeWitt, L.M.; Wollerman, A.L.

1993-02-01

The Mixed Waste Integrated Program (MWIP) is one of several US Department of Energy (DOE) integrated programs established to organize and coordinate throughout the DOE complex the development of technologies for treatment of specific waste categories. The goal of the MWIP is to develop and deploy appropriate technologies for -the treatment of DOE mixed low-level and alpha-contaminated wastes in order to bring all affected DOE installations and projects into compliance with environmental laws. Evaluation of treatment technologies by the MWIP will focus on meeting waste form performance requirements for disposal. Thermal treatment technologies were an early emphasis for the MWIP because thermal treatment is indicated (or mandated) for many of the hazardous constituents in DOE mixed waste and because these technologies have been widely investigated for these applications. An advisory group, the Thermal Treatment Working Group (TTWG), was formed during the program's infancy to assist the MWIP in evaluating and prioritizing thermal treatment technologies suitable for development. The results of the overall evaluation scoring indicate that the four highest-rated technologies were rotary kilns, slagging kilns, electric-arc furnaces, and plasma-arc furnaces. The four highest-rated technologies were all judged to be applicable on five of the six waste streams and are the only technologies in the evaluation with this distinction. Conclusions as to the superiority of one technology over others are not valid based on this preliminary study, although some general conclusions can be drawn

The PERC trademark process: Existing and potential applications for induction coupled plasma technology in hazardous and radioactive waste treatment

International Nuclear Information System (INIS)

Blutke, A.S.; Vavruska, J.S.; Serino, J.F.

1996-01-01

Plasma Technology, Inc. (PTI), a Santa Fe, New Mexico corporation has developed the Plasma Energy Recycle and Conversion (PERC)trademark treatment process as a safe and environmentally clean alternative to conventional thermal destruction technologies. The PERC trademark treatment process uses as its heat source an advanced Induction Coupled Plasma (ICP) torch connected to a reaction chamber system with an additional emission control system. For example, organic-based gas, liquid, slurry, and/or solid waste streams can be converted into usable or even salable products while residual emissions are reduced to an absolute minimum. In applications for treatment of hazardous and radioactive waste streams, the PERC system could be used for destruction of the hazardous organic constituents and/or significant waste volume reduction while capturing the radioactive fraction in a non-leachable form. Like Direct Current (DC) and Alternating Current (AC) arc plasma systems, ICP torches offer sufficient energy to decompose, melt and/or vitrify any waste stream. The decision for an arc plasma or an IC plasma system has to be made on a case by case evaluation and is highly dependent on the specific waste stream's form and composition. Induction coupled plasma technology offers one simple, but significant difference compared to DC or AC arc plasma systems: the ICP torch is electrodeless. To date, enormous research effort has been spent to improve the lifetime of electrodes and the effectiveness of related cooling systems. Arc plasma systems are established in research laboratories worldwide and are approaching a broad use in commercial applications. ICP technology has been improved relatively recently, but nowadays offers complete new and beneficial approaches in the field of waste conversion and treatment

Insights into the mechanisms of mercury sorption onto aluminum based drinking water treatment residuals

Energy Technology Data Exchange (ETDEWEB)

Deliz Quiñones, Katherine, E-mail: Katherine.Deliz@amecfw.com; Hovsepyan, Anna, E-mail: anna_Hovsepyan@urscorp.com; Oppong-Anane, Akua; Bonzongo, Jean-Claude J., E-mail: bonzongo@ufl.edu

2016-04-15

Highlights: • Mercury sorption by Al-WTRs involves electrostatic forces and chemisorption. • Hg forms bonds with oxygen and sulfur atoms of Al-WTR’s organic ligands. • Mercury is incorporated into the residual fraction to form stable complexes. • Mercury binds mainly to SiO{sub x} species in the residual fraction. - Abstract: Several studies have demonstrated the ability of drinking water treatment residuals (WTRs) to efficiently sorb metal cations from aqueous solutions. Reported results have stimulated interest on the potential use of WTRs as sorbent for metal removal from contaminated aqueous effluents as well as in metal immobilization in contaminated soils. However, knowledge on mechanisms of metal sorption by WTRs remains very limited and data on the long-term stability of formed metal–WTR complexes as a function of changing key environmental parameters are lacking. In this study, chemical selective sequential extraction (SSE), scanning electron microscopy combined with X-ray energy dispersive spectrometer (SEM-EDS), and X-ray photoelectron spectroscopy (XPS) were used to gain insight into the different mechanisms of mercury (Hg) binding to aluminum based WTR (Al-WTRs). Results from sorption studies show that a significant portion of Hg becomes incorporated in the operationally defined residual fraction of Al-WTRs, and therefore, not prone to dissolution and mobility. The results of solid phase analyses suggested that Hg immobilization by Al-WTR occurs largely through its binding to oxygen donor atoms of mineral ligands driven by a combination of electrostatic forces and covalent bonding.

Insights into the mechanisms of mercury sorption onto aluminum based drinking water treatment residuals

International Nuclear Information System (INIS)

Deliz Quiñones, Katherine; Hovsepyan, Anna; Oppong-Anane, Akua; Bonzongo, Jean-Claude J.

2016-01-01

Highlights: • Mercury sorption by Al-WTRs involves electrostatic forces and chemisorption. • Hg forms bonds with oxygen and sulfur atoms of Al-WTR’s organic ligands. • Mercury is incorporated into the residual fraction to form stable complexes. • Mercury binds mainly to SiO x species in the residual fraction. - Abstract: Several studies have demonstrated the ability of drinking water treatment residuals (WTRs) to efficiently sorb metal cations from aqueous solutions. Reported results have stimulated interest on the potential use of WTRs as sorbent for metal removal from contaminated aqueous effluents as well as in metal immobilization in contaminated soils. However, knowledge on mechanisms of metal sorption by WTRs remains very limited and data on the long-term stability of formed metal–WTR complexes as a function of changing key environmental parameters are lacking. In this study, chemical selective sequential extraction (SSE), scanning electron microscopy combined with X-ray energy dispersive spectrometer (SEM-EDS), and X-ray photoelectron spectroscopy (XPS) were used to gain insight into the different mechanisms of mercury (Hg) binding to aluminum based WTR (Al-WTRs). Results from sorption studies show that a significant portion of Hg becomes incorporated in the operationally defined residual fraction of Al-WTRs, and therefore, not prone to dissolution and mobility. The results of solid phase analyses suggested that Hg immobilization by Al-WTR occurs largely through its binding to oxygen donor atoms of mineral ligands driven by a combination of electrostatic forces and covalent bonding.

Investigation on reusing water treatment residuals to remedy soil contaminated with multiple metals in Baiyin, China

Energy Technology Data Exchange (ETDEWEB)

Wang, Changhui; Zhao, Yuanyuan [The Key Laboratory of Water and Sediment Sciences, Ministry of Education, School of Environment, Beijing Normal University, Beijing 100875 (China); Pei, Yuansheng, E-mail: yspei@bnu.edu.cn [The Key Laboratory of Water and Sediment Sciences, Ministry of Education, School of Environment, Beijing Normal University, Beijing 100875 (China)

2012-10-30

Highlights: Black-Right-Pointing-Pointer Fe/Al water treatment residuals (FARs) can stabilize As, Pb, Ni, Zn, Cr and Cu. Black-Right-Pointing-Pointer FARs cannot stabilize Ba and Cd. Black-Right-Pointing-Pointer The properties of FARs and soil affect the FARs' ability of stabilizing metals. - Abstract: In this work, the remediation of soils contaminated with multiple metals using ferric and alum water treatment residuals (FARs) in Baiyin, China, was investigated. The results of metals fractionation indicated that after the soil was treated with FARs, arsenic (As), lead (Pb), nickel (Ni), zinc (Zn) and copper (Cu) could be transformed into more stable forms, i.e., As bound in crystalline Fe/Al oxides and other metals in the oxidable and residual forms. However, the forms of chromium (Cr) and cadmium (Cd) were unaffected. Interestingly, due to the effect of FARs, barium (Ba) was predominantly transformed into more mobile forms. The bioaccessibility extraction test demonstrated that the FARs reduced the bioaccessibility of As by 25%, followed by Cu, Cr, Zn, Ni and Pb. The bioaccessibility of Cd and Ba were increased; in particular, there was an increase of 41% for Ba at the end of the test. In conclusion, the FARs can be used to remedy soil contaminated with multiple metals, but comprehensive studies are needed before practical applications of this work.

Selection of technologies for municipal wastewater treatment

Directory of Open Access Journals (Sweden)

Juan Pablo Rodríguez Miranda

2015-11-01

Full Text Available In water environmental planning in watersheds should contain aspects for the decontamination of receiving water body, therefore the selection of the treatment plants municipal wastewater in developing countries, you should consider aspects of the typical composition raw wastewater pollutant removal efficiency by technology, performance indicators for technology, environmental aspects of localization and spatial localization strategy. This methodology is built on the basis of technical, economic and environmental attributes, such as a tool for decision making future investments in treatment plants municipal wastewater with multidisciplinary elements.

Tracking the conversion of nitrogen during pyrolysis of antibiotic mycelial fermentation residues using XPS and TG-FTIR-MS technology.

Science.gov (United States)

Zhu, Xiangdong; Yang, Shijun; Wang, Liang; Liu, Yuchen; Qian, Feng; Yao, Wenqing; Zhang, Shicheng; Chen, Jianmin

2016-04-01

Antibiotic mycelial fermentation residues (AMFRs), which are emerging solid pollutants, have been recognized as hazardous waste in China since 2008. Nitrogen (N), which is an environmental sensitivity element, is largely retained in AMFR samples derived from fermentation substrates. Pyrolysis is a promising technology for the treatment of solid waste. However, the outcomes of N element during the pyrolysis of AMFRs are still unknown. In this study, the conversion of N element during the pyrolysis of AMFRs was tracked using XPS (X-ray photoelectron spectroscopy) and online TG-FTIR-MS (Thermogravimetry-Fourier transform infrared-Mass spectrometry) technology. In the AMFR sample, organic amine-N, pyrrolic-N, protein-N, pyridinic-N, was the main N-containing species. XPS results indicated that pyrrolic-N and pyridinic-N were retained in the AMFR-derived pyrolysis char. More stable species, such as N-oxide and quaternary-N, were also produced in the char. TG-FTIR-MS results indicated that NH3 and HCN were the main gaseous species, and their contents were closely related to the contents of amine-N and protein-N, and pyrrolic-N and pyridinic-N of AMFRs, respectively. Increases in heating rate enhanced the amounts of NH3 and HCN, but had less of an effect on the degradation degree of AMFRs. N-containing organic compounds, including amine-N, nitrile-N and heterocyclic-N, were discerned from the AMFR pyrolysis process. Their release range was extended with increasing of heating rate and carbon content of AMFR sample. This work will help to take appropriate measure to reduce secondary pollution from the treatment of AMFRs. Copyright © 2015 Elsevier Ltd. All rights reserved.

Integrating biological treatment of crop residue into a hydroponic sweetpotato culture

Science.gov (United States)

Trotman, A. A.; David, P. P.; Bonsi, C. K.; Hill, W. A.; Mortley, D. G.; Loretan, P. A.

1997-01-01

Residual biomass from hydroponic culture of sweetpotato [Ipomoea batatas (L.) Lam.] was degraded using natural bacterial soil isolates. Sweetpotato was grown for 120 days in hydroponic culture with a nutrient solution comprised of a ratio of 80% modified half Hoagland solution to 20% filtered effluent from an aerobic starch hydrolysis bioreactor. The phytotoxicity of the effluent was assayed with `Waldmann's Green' lettuce (Lactuca sativa L.) and the ratio selected after a 60-day bioassay using sweetpotato plants propagated vegetatively from cuttings. Controlled environment chamber experiments were conducted to investigate the impact of filtrate from biological treatment of crop residue on growth and storage root production with plants grown in a modified half Hoagland solution. Incorporation of bioreactor effluent, reduced storage root yield of `Georgia Jet' sweetpotato but the decrease was not statistically significant when compared with yield for plants cultured in a modified half Hoagland solution without filtrate. However, yield of `TU-82-155' sweetpotato was significantly reduced when grown in a modified half Hoagland solution into which filtered effluent had been incorporated. Total biomass was significantly reduced for both sweetpotato cultivars when grown in bioreactor effluent. The leaf area and dry matter accumulation were significantly (P < 0.05) reduced for both cultivars when grown in solution culture containing 20% filtered effluent.

Mixed and low-level waste treatment facility project. Volume 3, Waste treatment technologies (Draft)

Energy Technology Data Exchange (ETDEWEB)

1992-04-01

The technology information provided in this report is only the first step toward the identification and selection of process systems that may be recommended for a proposed mixed and low-level waste treatment facility. More specific information on each technology will be required to conduct the system and equipment tradeoff studies that will follow these preengineering studies. For example, capacity, maintainability, reliability, cost, applicability to specific waste streams, and technology availability must be further defined. This report does not currently contain all needed information; however, all major technologies considered to be potentially applicable to the treatment of mixed and low-level waste are identified and described herein. Future reports will seek to improve the depth of information on technologies.

Thermal treatment system of hazardous residuals in three heating zones based on a microprocessor

International Nuclear Information System (INIS)

Luna H, C.L.

1997-01-01

Thermal treatment system consists of a high power electric oven of three heating zones where each zone works up to 1200 Centigrades; it has the capacity of rising the central zone temperature up to 1000 Centigrades in 58 minutes approximately. This configuration of three zones could be programmed to different temperatures and they will be digitally controlled by a control microprocessor, which has been controlled by its own assembler language, in function of the PID control. There are also other important controls based on this microprocessor, as a signal amplification, starting and shutdown of high power step relays, activation and deactivation of both analogic/digital and digital/analogic convertors, port activation and basic data storage of the system. Two main characteristics were looked for this oven design; the first was the possibility of controlling the three zone temperature and the second was to reduce the rising and stabilization operation time and its digitized control. The principal function of the three zone oven is to accelerate the degradation of hazardous residuals by an oxidation instead combustion, through relatively high temperatures (minimum 800 Centigrades and maximum 1200 Centigrades); this process reduces the ash and volatile particulate production. The hazardous residuals will be pumped into the degradation system and after atomized through a packaged column; this step will avoid the direct contact of the residuals with the oven cores. These features make this system as closed process, which means that the residuals can not leak to the working area, reducing the exposure risk to the personnel. This three step oven system is the first stage of the complete hazardous residuals degradation system; after this, the flow will go into a cold plasma region where the process is completed, making a closed system. (Author)

Enhancing Intervention for Residual Rhotic Errors Via App-Delivered Biofeedback: A Case Study.

Science.gov (United States)

Byun, Tara McAllister; Campbell, Heather; Carey, Helen; Liang, Wendy; Park, Tae Hong; Svirsky, Mario

2017-06-22

Recent research suggests that visual-acoustic biofeedback can be an effective treatment for residual speech errors, but adoption remains limited due to barriers including high cost and lack of familiarity with the technology. This case study reports results from the first participant to complete a course of visual-acoustic biofeedback using a not-for-profit iOS app, Speech Therapist's App for /r/ Treatment. App-based biofeedback treatment for rhotic misarticulation was provided in weekly 30-min sessions for 20 weeks. Within-treatment progress was documented using clinician perceptual ratings and acoustic measures. Generalization gains were assessed using acoustic measures of word probes elicited during baseline, treatment, and maintenance sessions. Both clinician ratings and acoustic measures indicated that the participant significantly improved her rhotic production accuracy in trials elicited during treatment sessions. However, these gains did not transfer to generalization probes. This study provides a proof-of-concept demonstration that app-based biofeedback is a viable alternative to costlier dedicated systems. Generalization of gains to contexts without biofeedback remains a challenge that requires further study. App-delivered biofeedback could enable clinician-research partnerships that would strengthen the evidence base while providing enhanced treatment for children with residual rhotic errors. https://doi.org/10.23641/asha.5116318.

TREATMENT TECHNOLOGIES FOR ARSENIC REMOVAL

Science.gov (United States)

The United States Environmental Protection Agency (US EPA) recently reduced the arsenic maximum contaminant level (MCL) from 0.050 mg/L to 0.010 mg/L. In order to increase arsenic outreach efforts, a summary of the new rule, related health risks, treatment technologies, and desig...

Technology for recycling of manure and organic residues in a whole-farm perspective. Vol. 2

Energy Technology Data Exchange (ETDEWEB)

Petersen, Soeren O. (ed.)

2006-08-15

Efficient use of agricultural residues and imported waste materials within agriculture is increasingly viewed from a whole-farm perspective. A wide range of management decisions - including feeding, manure collection systems, and treatment for hygienization or energy production - influence the nutrient value and environmental impact of agricultural residues. Field application of manure and urban wastes are affected by societal constraints, such as legislation, tradition, consumer attitudes towards waste recycling, and pollution risks. Hence, the optimal use of manure and organic wastes as a nutrient source and soil conditioner interacts strongly with many other aspects of farming. The objective behind this 12th International Conference of the Ramiran network is to present and discuss on-farm interactions between manure and waste management practices, and to consider methods to describe and quantify the overall effects of a given strategy or treatment practice. Accordingly, the research presented at the conference and in the proceedings cover a wide range of topics, from feed impact on manure composition to environmental losses in the field, from energy production to odour control, from biochemistry to modelling. We hope that everyone involved in the conference will see this as an opportunity to discover interfaces with other research areas that can strengthen the whole-farm perspective of future research. (au)

Technology for recycling of manure and organic residues in a whole-farm perspective. Vol. 1

Energy Technology Data Exchange (ETDEWEB)

Petersen, Soeren O. (ed.)

2006-08-15

Efficient use of agricultural residues and imported waste materials within agriculture is increasingly viewed from a whole-farm perspective. A wide range of management decisions - including feeding, manure collection systems, and treatment for hygienization or energy production - influence the nutrient value and environmental impact of agricultural residues. Field application of manure and urban wastes are affected by societal constraints, such as legislation, tradition, consumer attitudes towards waste recycling, and pollution risks. Hence, the optimal use of manure and organic wastes as a nutrient source and soil conditioner interacts strongly with many other aspects of farming. The objective behind this 12th International Conference of the Ramiran network is to present and discuss on-farm interactions between manure and waste management practices, and to consider methods to describe and quantify the overall effects of a given strategy or treatment practice. Accordingly, the research presented at the conference and in the proceedings cover a wide range of topics, from feed impact on manure composition to environmental losses in the field, from energy production to odour control, from biochemistry to modelling. We hope that everyone involved in the conference will see this as an opportunity to discover interfaces with other research areas that can strengthen the whole-farm perspective of future research. (au)

Noninvasive treatment choice for an aged down syndrome patient presenting a residual periapical cyst.

Science.gov (United States)

Sperandio, Felipe Fornias; Carli, Marina Lara de; Guimaräes, Eduardo Pereira; Pereira, Alessandro Antônio Costa; Hanemann, Joäo Adolfo Costa

2014-03-01

This is the first report to illustrate the marsupialization as an effective treatment for a Down Syndrome (DS) patient presenting a residual periapical cyst. These cysts occur within the alveolar ridge, usually at the local site of a previously extracted tooth that did not received proper curettage; usually the surgical excision of a cyst and also the vigorous curettage of a socket is very simple, if not for the fact that mentally disabled patients require rapid and non-stressful procedures. The 54-year-old DS patient represented herein received a minimally invasive marsupialization under local anesthesia. Due to the large extent of the lesion, the acrylic resin drain was maintained for 30 days. Through the following period, a daily irrigation of the cystic cavity with saline solution was carried out to prevent a secondary infection within the cystic cavity. A follow-up of 16 months showed no signs of recurrence. Marsupialization of residual periapical cyst is completely effective and safe, even for a DS patient that is considered to be at an advanced age. Marsupialization poses as a minimally invasive choice for mentally disabled patients, even when presenting advanced ages; treatment success was stated by the easy clinical conduct, uneventful postoperative situation and the lack of recurrence along 16 months of follow-up.

Water Treatment Technology - Distribution Systems.

Science.gov (United States)

Ross-Harrington, Melinda; Kincaid, G. David

One of twelve water treatment technology units, this student manual on distribution systems provides instructional materials for six competencies. (The twelve units are designed for a continuing education training course for public water supply operators.) The competencies focus on the following areas: types of pipe for distribution systems, types…

A review of treatment technologies for MTBE

International Nuclear Information System (INIS)

Bass, D.

1995-01-01

Available treatment technologies for methyl tertiary butyl ether (MTBE) contamination in soil, groundwater, and recovered groundwater are reviewed and assessed. MTBE contamination is becoming an important issue due to the increasing prevalence and regulation of this gasoline additive. In addition, MTBE is more soluble and more mobile in groundwater than most hydrocarbons, so it is usually the first gasoline constituent to reach sensitive receptors. Treatment of MTBE is complicated by its Henry's constant, which is lower than most other gasoline constituents. Furthermore, evidence of biodegradability of MTBE is mixed, and MTBE does not degrade rapidly abiotically. Groundwater pumping is usually employed to contain and collect MTBE-contaminated groundwater, often successfully because of its high aqueous solubility. Air sparging/soil vapor extraction is also successfully employed to treat MTBE, but its effectiveness is reduced by the low Henry's constant of MTBE. Sparging and other aerobic bioremediation approaches are hampered by the poor biodegradability of MTBE. Oxidation technologies, such as ozone injection, hold promise for rapid in situ remediation of MTBE. Treatment of recovered groundwater contaminated with MTBE is also problematic. MTBE adsorbs poorly to granular activated carbon; advanced oxidation processes are effective on MTBE, but entail high capital and operating costs; bioreactors are of questionable effectiveness on MTBE. Air stripping is usually the most cost-effective treatment technology for MTBE so long as the off gas from the air stripper can be discharged without treatment. However, off gas treatment is expensive, so groundwater is sometimes heated to reduce the requirement for stripping air

Neutron diffraction measurements for the determination of heat treatment effectiveness in generating compressive residual stress in an automotive crown gear

International Nuclear Information System (INIS)

Albertini, G.; Fiori, F.; Girardin, E.; Giuliani, A.; Pyzalla, A.; Quadrini, E.

1999-01-01

Complete text of publication follows. Thermal austenitizing and tempering treatments are being developed in automotive industry to prevent crack initiation and avoid crack propagation, especially in components where stress intensity factors influence the stress field and then the fatigue life of the component itself. This is the case of crown gears, where the teeth root undergoes frequently to cracking when tensile residual stresses are present at the surface, as typical loads are impulsive and very high. The sign reversal of these stresses is the aim of austenitizing and tempering treatments. In this work residual stress measurements carried out at HMI-BENSC are presented, in a UNI55Cr3 steel crown gear submitted to such kind of treatments, performed with a new multi-frequency induction technique whose effectiveness is checked. (author)

Management of industrial solid residues; Gerenciamento de residuos solidos industriais

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-07-01

This chapter gives an overview on the management of industrial solid wastes, approaching the following subjects: classification of industrial solid residues; directives and methodologies for the management of industrial solid residues; instruments for the management of industrial solid residues; handling, packing, storage and transportation; treatment of industrial solid residues; final disposal - landfill for industrial residues; the problem of treatment and final disposer of domestic garbage in Brazil; recycling of the lubricant oils used in brazil; legislation.

Differential Effects of Visual-Acoustic Biofeedback Intervention for Residual Speech Errors

Science.gov (United States)

McAllister Byun, Tara; Campbell, Heather

2016-01-01

Recent evidence suggests that the incorporation of visual biofeedback technologies may enhance response to treatment in individuals with residual speech errors. However, there is a need for controlled research systematically comparing biofeedback versus non-biofeedback intervention approaches. This study implemented a single-subject experimental design with a crossover component to investigate the relative efficacy of visual-acoustic biofeedback and traditional articulatory treatment for residual rhotic errors. Eleven child/adolescent participants received ten sessions of visual-acoustic biofeedback and 10 sessions of traditional treatment, with the order of biofeedback and traditional phases counterbalanced across participants. Probe measures eliciting untreated rhotic words were administered in at least three sessions prior to the start of treatment (baseline), between the two treatment phases (midpoint), and after treatment ended (maintenance), as well as before and after each treatment session. Perceptual accuracy of rhotic production was assessed by outside listeners in a blinded, randomized fashion. Results were analyzed using a combination of visual inspection of treatment trajectories, individual effect sizes, and logistic mixed-effects regression. Effect sizes and visual inspection revealed that participants could be divided into categories of strong responders (n = 4), mixed/moderate responders (n = 3), and non-responders (n = 4). Individual results did not reveal a reliable pattern of stronger performance in biofeedback versus traditional blocks, or vice versa. Moreover, biofeedback versus traditional treatment was not a significant predictor of accuracy in the logistic mixed-effects model examining all within-treatment word probes. However, the interaction between treatment condition and treatment order was significant: biofeedback was more effective than traditional treatment in the first phase of treatment, and traditional treatment was more effective

Applications of artificial intelligence technology to wastewater treatment fields in China

Institute of Scientific and Technical Information of China (English)

QING Xiao-xia; WANG Bo; MENG De-tao

2005-01-01

Current applications of artificial intelligence technology to wastewater treatment in China are summarized. Wastewater treatment plants use expert system mainly in the operation decision-making and fault diagnosis of system operation, use artificial neuron network for system modeling, water quality forecast and soft measure, and use fuzzy control technology for the intelligence control of wastewater treatment process. Finally, the main problems in applying artificial intelligence technology to wastewater treatment in China are analyzed.

Use of residual hydrocarbons treated by Thermal Plasma (recovery of energy by-products)

International Nuclear Information System (INIS)

Carreno B, J.A.; Pacheco S, J.O.; Ramos F, F.; Cruz A, A.; Duran G, M.

2001-01-01

The emergence of new technologies is getting greater importance for the control of pollution. One of them is the destruction of hazardous wastes treated by thermal plasma, which is of special interest for the efficient treatment of the hazardous wastes since the heat generated by thermal plasma is able to destroy the molecular bonds generating solids and gaseous products which do not represent danger for the human being and the environment. The thermal plasma is the suitable technology for treating a wide range of hazardous wastes, including the residual hydrocarbons from the refinement process of petroleum, plasma exceeds the barrier of 3000 Centigrade. The efficiency of the degradation of residues is greater than 99.99%. Toxic emissions are not generated to environment as SO 2 , NO x and CO 2 neither dioxins and furans by being a pyrolysis process. The use of hydrogen as fuel does not generate pollution to environment. (Author)

Effect of pre-treatments on methane production potential of energy crops and crop residues

Energy Technology Data Exchange (ETDEWEB)

Lehtomaki, A.; Ronkainen; Rintala, J.A. [Jyvaskla Univ. (Finland). Dept. of Biological and Environmental Sciences; Viinikainen, T.A. [Jyvaskla Univ. (Finland). Dept. of Chemistry

2004-07-01

Energy crops, that is, crops grown specifically for energy purposes are an alternative to food production in areas with sufficient agricultural land. Crop residues are also a potential source of energy. The anaerobic digestion of solid materials is limited by hydrolysis of complex polymeric substances such as lignocellulose. The methane producing potential of ligno cellulosic material is to pretreat the substrate in order to break up the polymer chains to more easily accessible soluble compounds. In this study, three different substrates were used: sugar beet tops, grass hay, and straw of oats. Biological pretreatments were the following: enzyme treatment, composting, white-rot fungi treatment. Also, pretreatment in water was tried. Chemical pretreatments included peracetic acid treatment, and treatment with two different alkalis. Alkaline pretreatments of hay and sugar beet tops have the potential to improve the methane yield. For instance, the yield of grass hay was increased 15 per cent by one particular alkaline treatment. Straw did not respond to any of the treatments tried. 18 refs., 1 tab., 2 figs.

Water treatment for fossil fuel power generation - technology status report

International Nuclear Information System (INIS)

2006-01-01

This technology status report focuses on the use of water treatment technology in fossil fuel power plants. The use of polymeric ion exchange resins for deionization of water, the currently preferred use of ion exchange for economically treating water containing low dissolved salts, the use of low pressure high-flux membranes, membrane microfiltration, and reverse osmosis are discussed. Details are given of the benefits of the technologies, water use at power plants, the current status of water treatment technologies, and the potential for future developments, along with power plant market trends and potentials, worldwide developments, and UK capabilities in water treatment plant design and manufacturing

Residual stress evaluation by neutron diffraction. Some industrial applications and perspectives

International Nuclear Information System (INIS)

Rogante, M.

2001-01-01

Materials and components of technological and industrial interest can present Residual Stresses (RS), that can be generated during the manufacturing process - e. g. extruding, welding, and forging -, or as a consequence of plastic deformations or thermal treatments. When RS add to external loads, they can enhance fatigue processes, earlier inducing failure of the component. Examples of RS determination in industrial applications are reported: the one focuses on AA 6082 alloy extruded samples, the other on a 2,25Cr1Mo ferritic steel welded pipe after thermal treatment. Other examples are shown, successively, concerning particular industrial problems which need to be studied also by adopting the same technique. (R.P.)

Development of the destruction technology for radioactive organic solid wastes

Energy Technology Data Exchange (ETDEWEB)

Oh, Won Zin; Park, H.S.; Lee, K.W. [and others

1999-04-01

The followings were studied through the project entitled 'Technology development for nuclear fuel cycle waste treatment'. 1. Organic waste decomposition technology development A. Destruction technology for organic wastes using Ag(2)-mediated electrochemical oxidation B. Recovery and regeneration technology for the spent chemicals used in the MEO process 2. Radioactive metal waste recycling technology A. Surface decontamination processes B. Decontamination waste treatment technology 3. Volume reduction technology nuclear fuel cycle (NFC) technology A. Estimation of the amount of radwastes and the optimum volume reduction methodology of domestic NFC B. Pretreatment of spent fuel cladding by electrochemical decontamination C. Hot cell process technology for the treatment of NFC wastes 4. Design and fabrication of the test equipment of volume reduction and reuse of alpha contaminated wastes 5. Evaluation on environmental compatibility of NFC A. Development of evaluation methodology on environmental friendliness of NFC B. Residual activity assessment of recycling wastes. (author). 321 refs., 54 tabs., 183 figs.

Development of the destruction technology for radioactive organic solid wastes

International Nuclear Information System (INIS)

Oh, Won Zin; Park, H.S.; Lee, K.W.

1999-04-01

The followings were studied through the project entitled 'Technology development for nuclear fuel cycle waste treatment'. 1. Organic waste decomposition technology development A. Destruction technology for organic wastes using Ag(2)-mediated electrochemical oxidation B. Recovery and regeneration technology for the spent chemicals used in the MEO process 2. Radioactive metal waste recycling technology A. Surface decontamination processes B. Decontamination waste treatment technology 3. Volume reduction technology nuclear fuel cycle (NFC) technology A. Estimation of the amount of radwastes and the optimum volume reduction methodology of domestic NFC B. Pretreatment of spent fuel cladding by electrochemical decontamination C. Hot cell process technology for the treatment of NFC wastes 4. Design and fabrication of the test equipment of volume reduction and reuse of alpha contaminated wastes 5. Evaluation on environmental compatibility of NFC A. Development of evaluation methodology on environmental friendliness of NFC B. Residual activity assessment of recycling wastes. (author). 321 refs., 54 tabs., 183 figs

The potential use of ionising energy treatment in Queensland's horticultural industries

International Nuclear Information System (INIS)

Heather, N.W.; Sheehy, P.T.; Muirhead, I.F.; Brown, B.I.; Hassall, R.N.

1985-01-01

The potential application of ionising energy treatment technology in Queensland falls into three categories: insect disinfestation, disease control and quality improvement. The technology fulfils the requirements of a disinfestation treatment against Queensland fruit fly and other pests of quarantine importance in respect to efficacy, absence of phytotoxicity, absence of residues and, on technical considerations would be an ideal replacement for the fumigant EDB. The report examines the purposes of ionising energy treatment, economic and marketing aspects and research needs

Quality of diets with fluidized bed combustion residue treatment: I. Rat trials

Energy Technology Data Exchange (ETDEWEB)

Cahill, N.J.; Reid, R.L.; Head, M.K.; Hern, J.L.; Bennett, O.L.

Feeding trials were conducted with rats (Rattus rattus) to examine effects of soil application, or dietary inclusion, of fluidized bed combustion residue (FBCR) on the composition and quality of foods. Four diets (vegetable protein, egg protein, chicken, chicken + dietary FBCR) prepared with either FBCR or lime (control) treatments, were fed to weanling, female rats in three growth and reproduction trials. Intake, growth rate, and composition of body and organs of rats were measured. Rats in one trial were bred, their litters maintained on dietary treatments, and the offspring rebred. Treatment (FBCR vs. lime) x diet interactions on food composition and animal responses generally were not significant. Treatment had little effect on element composition of diets; mineral concentrations were in normal ranges. Diet treatment with FBCR depressed (P<0.01) food intake and growth of rats in one trial, but not in others, and had no effect (P<0.05) on body water, protein, ether extract, or gross energy composition. Some differences in element concentrations in the carcass and organs of rats and pups resulted from FBCR treatment, but effects were small and inconsistent. Litters from the first reproductive cycle appeared normal, except for animals fed the chicken + dietary FBCR treatment, on which pups showed poor growth and anemia. Offspring from certain diets were rebred and litters showed a high mortality, although this was not associated specifically with FBCR treatment. Results indicated no major detrimental effects on food composition, or growth, tissue element accumulation, and reproduction in the rat relating to use of FBCR as a soil amendment. 20 refs., 9 tabs.

Treatment of residual waters of slaughterhouses with filters

International Nuclear Information System (INIS)

Ortiz A, Jesus Mario

1995-01-01

For studying the anaerobic treatment of the residual waters coming from a slaughterhouse of bovine livestock, they were used a system of two filters in series and a third unique filter as witness. With values average of load organic volumetric and time of retention of 1.6 kg/(m 3 d) and 26 hours respectively, the efficiencies of removal of total DQO were similar in the unique filter and in the system in series, of the order of 64% on the average. Likewise, the retention and accumulation of biological solids in the channel were shown as the main road of removal of the DQO. The differentiation of the process achieved with the two filters in series allowed establishing that most of the accumulation happened in the primary filter, as long as the fundamental of the bioconversion in methane took place in the secondary filter of the system in series. The first relative level of methanegenization obtained could be explained by the limitations to the activity of the methanogenic biomass imposed by the low temperatures, although it could not discard a probable inhibition for the hydrolysis products of the accumulated fats

Residual sleep disturbance and risk of relapse during the continuation/maintenance phase treatment of major depressive disorder with the selective serotonin reuptake inhibitor fluoxetine

Directory of Open Access Journals (Sweden)

McGrath Patrick J

2010-02-01

Full Text Available Abstract Background Relapse of major depressive disorder (MDD is a common clinical problem. This study was designed to determine whether residual sleep disturbance (insomnia and hypersomnia predict risk of relapse during the continuation and maintenance treatment of MDD. Methods A total of 570 patients with MDD were treated with open-label, flexible dose fluoxetine (range 20 to 60 mg; mean dose = 45.8 mg/day; SD = 15.1 for 12 weeks. Under double blind conditions, 262 patients who achieved clinical response were randomly assigned to continue fluoxetine or to switch to placebo for 52 weeks or until relapse. Residual sleep disturbance during the baseline visit of the double-blind phase was assessed using items 4, 5, 6 (insomnia and 22, 23, 24 (hypersomnia of the Hamilton Depression Rating Scale (HDRS. Survival analysis was utilized to determine the effect of residual sleep disturbance on risk of relapse. Results The severities of early (P > 0.05, middle (P > 0.05, late (P > 0.05, or total (P > 0.05 residual insomnia were not found to significantly predict risk of relapse during continuation and maintenance-phase treatment. Similarly, the severities of early bedtime (P > 0.05, oversleeping (P > 0.05, napping (P > 0.05, or total (P > 0.05 residual hypersomnia were not found to significantly predict risk of relapse during continuation and maintenance-phase treatment. Conclusion The present study did not identify the severity of residual sleep disturbance among fluoxetine responders to predict risk of MDD relapse. The size of our sample may have precluded us from identifying more modest effects of residual sleep disturbance on the risk of relapse in MDD patients. Future studies are needed to further explore the relationship between residual sleep disturbance and relapse in MDD. Trial Registration ClinicalTrials.gov Identifier: NCT00427128

Sludge pumping in water treatment

International Nuclear Information System (INIS)

Solar Manuel, M. A.

2010-01-01

In water treatment processes is frequent to separate residual solids, with sludge shape, and minimize its volume in a later management. the technologies to applicate include pumping across pipelines, even to long distance. In wastewater treatment plants (WWTP), the management of these sludges is very important because their characteristics affect load losses calculation. Pumping sludge can modify its behavior and pumping frequency can concern treatment process. This paper explains advantages and disadvantages of different pumps to realize transportation sludge operations. (Author) 11 refs.

Proceedings of the 8. biennial residual wood conference

Energy Technology Data Exchange (ETDEWEB)

NONE

2009-07-01

This conference highlighted practical strategies for managing and utilizing residual wood as a true industry resource. Examples of successful wood energy projects were presented along with the technology and products of more than 30 companies involved in the residual wood business. The topics of discussion ranged from biomass supplies, quality issues, and harvesting guidelines to emerging biomass technologies, project overviews, and financing. The presentations outlined the many opportunities that exist for the forest industry to produce energy from biostock, such as healthy and diseased trees, underbrush, sawdust, wood chips, wood pulp and black liquor. Increasing fuel and energy costs along with advances in technology are improving the economy of forest-based biorefineries. The presentations showed how the industry can gain revenue from residual wood, which is steadily becoming a more valuable resource for pellet production and energy generation The conference featured 20 presentations, of which 3 have been catalogued separately for inclusion in this database. refs., tabs., figs.

Evaluation of innovative arsenic treatment technologies :the arsenic water technology partnership vendors forums summary report.

Energy Technology Data Exchange (ETDEWEB)

Everett, Randy L.; Siegel, Malcolm Dean; McConnell, Paul E.; Kirby, Carolyn (Comforce Technical Services, Inc.)

2006-09-01

The lowering of the drinking water standard (MCL) for arsenic from 50 {micro}g/L to 10 {micro}g/L in January 2006 could lead to significant increases in the cost of water for many rural systems throughout the United States. The Arsenic Water Technology Partnership (AWTP), a collaborative effort of Sandia National Laboratories, the Awwa Research Foundation (AwwaRF) and WERC: A Consortium for Environmental Education and Technology Development, was formed to address this problem by developing and testing novel treatment technologies that could potentially reduce the costs of arsenic treatment. As a member of the AWTP, Sandia National Laboratories evaluated cutting-edge commercial products in three annual Arsenic Treatment Technology Vendors Forums held during the annual New Mexico Environmental Health Conferences (NMEHC) in 2003, 2004 and 2005. The Forums were comprised of two parts. At the first session, open to all conference attendees, commercial developers of innovative treatment technologies gave 15-minute talks that described project histories demonstrating the effectiveness of their products. During the second part, these same technologies were evaluated and ranked in closed sessions by independent technical experts for possible use in pilot-scale field demonstrations being conducted by Sandia National Laboratories. The results of the evaluations including numerical rankings of the products, links to company websites and copies of presentations made by the representatives of the companies are posted on the project website at http://www.sandia.gov/water/arsenic.htm. This report summarizes the contents of the website by providing brief descriptions of the technologies represented at the Forums and the results of the evaluations.

Immobilization of acid digestion residue

International Nuclear Information System (INIS)

Greenhalgh, W.O.; Allen, C.R.

1983-01-01

Acid digestion treatment of nuclear waste is similar to incineration processes and results in the bulk of the waste being reduced in volume and weight to some residual solids termed residue. The residue is composed of various dispersible solid materials and typically contains the resultant radioactivity from the waste. This report describes the immobilization of the residue in portland cement, borosilicate glass, and some other waste forms. Diagrams showing the cement and glass virtification parameters are included in the report as well as process steps and candidate waste product forms. Cement immobilization is simplest and probably least expensive; glass vitrification exhibits the best overall volume reduction ratio

Reuse of drinking water treatment residuals in a continuous stirred tank reactor for phosphate removal from urban wastewater.

Science.gov (United States)

Bai, Leilei; Wang, Changhui; Pei, Yuansheng; Zhao, Jinbo

2014-01-01

This work proposed a new approach of reusing drinking water treatment residuals (WTR) in a continuous stirred tank reactor (CSTR) to remove phosphate (P) from urban wastewater. The results revealed that the P removal efficiency of the WTR was more than 94% for urban wastewater, in the condition of initial P concentration (P0) of 10 mg L⁻¹, hydraulic retention time (HRT) of 2 h and WTR dosage (M0) of 10 g L⁻¹. The P mass transfer from the bulk to the solid-liquid interface in the CSTR system increased at lower P0, higher M0 and longer HRT. The P adsorption capacity of WTR from urban wastewater was comparable to that of the 201 × 4 resin and unaffected by ions competition. Moreover, WTR had a limited effect on the metals' (Fe, Al, Zn, Cu, Mn and Ni) concentrations of the urban wastewater. Based on the principle of waste recycling, the reuse of WTR in CSTR is a promising alternative technology for P removal from urban wastewater.

Emission of gaseous organic pollutants and flue gas treatment technology

International Nuclear Information System (INIS)

Chmielewski, A.G.; Sun, Y.

2007-01-01

Gaseous organic pollutants are emitted into atmosphere from various sources, creating a threat to the environment and man. New, economical technologies are needed for flue gas treatment. Emission sources of pollutants are reviewed and different treatment technologies are discussed in this report. (authors)

Sodium-bearing Waste Treatment Technology Evaluation Report

Energy Technology Data Exchange (ETDEWEB)

Charles M. Barnes; Arlin L. Olson; Dean D. Taylor

2004-05-01

Sodium-bearing waste (SBW) disposition is one of the U.S. Department of Energy (DOE) Idaho Operation Office’s (NE-ID) and State of Idaho’s top priorities at the Idaho National Engineering and Environmental Laboratory (INEEL). The INEEL has been working over the past several years to identify a treatment technology that meets NE-ID and regulatory treatment requirements, including consideration of stakeholder input. Many studies, including the High-Level Waste and Facilities Disposition Environmental Impact Statement (EIS), have resulted in the identification of five treatment alternatives that form a short list of perhaps the most appropriate technologies for the DOE to select from. The alternatives are (a) calcination with maximum achievable control technology (MACT) upgrade, (b) steam reforming, (c) cesium ion exchange (CsIX) with immobilization, (d) direct evaporation, and (e) vitrification. Each alternative has undergone some degree of applied technical development and preliminary process design over the past four years. This report presents a summary of the applied technology and process design activities performed through February 2004. The SBW issue and the five alternatives are described in Sections 2 and 3, respectively. Details of preliminary process design activities for three of the alternatives (steam reforming, CsIX, and direct evaporation) are presented in three appendices. A recent feasibility study provides the details for calcination. There have been no recent activities performed with regard to vitrification; that section summarizes and references previous work.

Investigation study for technological application of alternative methods for the energy exploitation of biomass/agricultural residues in Northern Greece

Directory of Open Access Journals (Sweden)

Zabaniotou Anastasia A.

2007-01-01

Full Text Available Biomass energy potential is addressed to be the most promising among the renewable energy sources, due to its spread and availability worldwide. Apart form that, biomass has the unique advantage among the rest of renewable energy sources, to be able to provide solid, liquid, and gaseous fuels that can be stored, transported, and utilized, far away from the point of origin. For the northern region of Macedonia in Greece, biomass utilization is considered to be a major issue, due to the considerably intensive regional agricultural activities. Wood by-products, fruit cores, rice husk and cotton gin waste provide a promising energy source for the region. The energy potential of the available agricultural biomass produced in the region is much enough to cover the 10% of the annual oil consumption utilized for thermal applications. However, the cost of energy utilization of biomass is considerably high due to the high cost of the logistics concerning the collection, transport, and storage of biomass. The available utilization technologies developed, to handle efficiently all different species of biomass, cover a wide technological range. One of the most promising technologies involving thermal treatment of biomass and the production of a gaseous fuel (biogas for industrial heat applications and electricity production, is the thermo chemical conversion. In the present work, an investigation concerning biomass potential for energy production in the region of central Macedonia in Greece, utilizing several locally produced biomass species, is conducted. Emphasis is put on the energy utilization of agricultural by-products and residues. Agricultural sector is of great importance due to the considerably intensive agricultural activities in the region of Central Macedonia. .

Modification of Wastewater Treatment Technology at Cottonseed Oil Plant

Directory of Open Access Journals (Sweden)

Alshabab Mary Shick

2016-01-01

Full Text Available Wastewaters from cottonseed oil producing plant in Syria were studied in laboratory experiments. Aim of the study was to suggest modification of wastewater treatment technology in order to increase its efficiency. Concentration of pollutants in wastewaters was controlled by measurement of COD. According to the results of experiments it was suggested to decrease significantly (8-20 times dosages of reagents (acidifier, coagulant, flocculant in several actual stages of treatment (acidification, separation, coagulation and sedimentation and add stage of dispersed air flotation before coagulation treatment. The modified wastewater treatment technology would reduce COD to the values allowed for irrigation waters by Syrian National Standard.

Cover crop residue management for optimizing weed control

NARCIS (Netherlands)

Kruidhof, H.M.; Bastiaans, L.; Kropff, M.J.

2009-01-01

Although residue management seems a key factor in residue-mediated weed suppression, very few studies have systematically compared the influence of different residue management strategies on the establishment of crop and weed species. We evaluated the effect of several methods of pre-treatment and

Identification and assessment of site treatment plan implementation opportunities for emerging technologies

International Nuclear Information System (INIS)

Bernard, E.A.

1995-01-01

The Department of Energy (DOE), in response to the 1992 Federal Facility Compliance Act, has prepared Site Treatment Plans (STP) for the approximately 2,000 waste streams identified within its mixed waste inventory Concurrently, emerging mixed waste treatment technologies are in final development. This paper defines a three-phase process to identify and assess implementation opportunities for these emerging technologies within the STP. It highlights the first phase, functional matching of expected treatment capabilities with proposed treatment requirements. Matches are based on treatment type, regulated contaminant and waste matrix type, for both capabilities and requirements. Results identify specific waste streams and volumes that could be treated by each emerging technology. A study for Plasma Hearth Process, Delphi DETOX sm , Supercritical Water Oxidation and Vitrification shows that about 200,000 ml of DOE's mixed waste inventory can potentially be treated by one or more of these emerging technologies. Actual implementations are small fractions of the treatable inventory. Differences between potential and actual implementations must be minimized to accrue optimum benefit from implementation of emerging or alternative treatment technologies. Functional matching is the first phase in identifying and quantifying benefits, addressing technology system and treatment issues, and providing, in part, the basis for STP implementation decisions. DOE, through EM's Office of Technology Development, has funded this work

Investigation of an innovative technology for oil-field brine treatment

Energy Technology Data Exchange (ETDEWEB)

Miskovic, D; Dalmacija, B; Hain, Z; Karlovic, E; Maric, S; Uzelac, N [Inst. of Chemistry, Faculty of Sciences, V. Vlahovica 2 (YU)

1989-01-01

Various aspects of an innovative technology for oil field brine treatment were investigated on a laboratory scale. The both free and dispersed oily matter were separated by gravitation and sedimentation. Apart from the physico-chemical oil removal process, special attention was paid to different variants of improved microbiological treatment: dilution with fresh water and application of powdered activated carbon (PAC). Advanced treatment was carried out on granular biological activated carbon (GBAC). A technological scheme for complete treatment was proposed. (author).

SOLUTIONS TO OVERCOME BARRIERS TO IMPLEMENTATION OF TREATMENT TECHNOLOGIES

Science.gov (United States)

To make treatment a viable option for remediation you must first identify the barriers to implementing treatment. The primary barrier is economics. Treatment options are relatively expensive and there is a lack of funds for treatment. The cost of technologies can be lowered by 1)...

On-treatment non-high-density lipoprotein cholesterol, apolipoprotein B, triglycerides, and lipid ratios in relation to residual vascular risk after treatment with potent statin therapy

DEFF Research Database (Denmark)

Mora, Samia; Glynn, Robert J; Boekholdt, S Matthijs

2012-01-01

The goal of this study was to determine whether residual risk after high-dose statin therapy for primary prevention individuals with reduced levels of low-density lipoprotein cholesterol (LDL-C) is related to on-treatment apolipoprotein B, non-high-density lipoprotein cholesterol (non-HDL-C), tri...

A comparison of corn (Zea mays L.) residue and its biochar on soil C and plant growth.

Science.gov (United States)

Calderón, Francisco J; Benjamin, Joseph; Vigil, Merle F

2015-01-01

In order to properly determine the value of charring crop residues, the C use efficiency and effects on crop performance of biochar needs to be compared to the un-charred crop residues. In this study we compared the addition of corn stalks to soil, with equivalent additions of charred (300 °C and 500 °C) corn residues. Two experiments were conducted: a long term laboratory mineralization, and a growth chamber trial with proso millet plants. In the laboratory, we measured soil mineral N dynamics, C use efficiency, and soil organic matter (SOM) chemical changes via infrared spectroscopy. The 300 °C biochar decreased plant biomass relative to a nothing added control. The 500°C biochar had little to no effect on plant biomass. With incubation we measured lower soil NO3 content in the corn stalk treatment than in the biochar-amended soils, suggesting that the millet growth reduction in the stalk treatment was mainly driven by N limitation, whereas other factors contributed to the biomass yield reductions in the biochar treatments. Corn stalks had a C sequestration use efficiency of up to 0.26, but charring enhanced C sequestration to values that ranged from 0.64 to 1.0. Infrared spectroscopy of the soils as they mineralized showed that absorbance at 3400, 2925-2850, 1737 cm-1, and 1656 cm-1 decreased during the incubation and can be regarded as labile SOM, corn residue, or biochar bands. Absorbances near 1600, 1500-1420, and 1345 cm-1 represented the more refractory SOM moieties. Our results show that adding crop residue biochar to soil is a sound C sequestration technology compared to letting the crop residues decompose in the field. This is because the resistance to decomposition of the chars after soil amendment offsets any C losses during charring of the crop residues.

Cellulose Nanomaterials in Water Treatment Technologies

Science.gov (United States)

Carpenter, Alexis Wells; de Lannoy, Charles François; Wiesner, Mark R.

2015-01-01

Cellulose nanomaterials are naturally occurring with unique structural, mechanical and optical properties. While the paper and packaging, automotive, personal care, construction, and textiles industries have recognized cellulose nanomaterials’ potential, we suggest cellulose nanomaterials have great untapped potential in water treatment technologies. In this review, we gather evidence of cellulose nanomaterials’ beneficial role in environmental remediation and membranes for water filtration, including their high surface area-to-volume ratio, low environmental impact, high strength, functionalizability, and sustainability. We make direct comparison between cellulose nanomaterials and carbon nanotubes (CNTs) in terms of physical and chemical properties, production costs, use and disposal in order to show the potential of cellulose nanomaterials as a sustainable replacement for CNTs in water treatment technologies. Finally, we comment on the need for improved communication and collaboration across the myriad industries invested in cellulose nanomaterials production and development to achieve an efficient means to commercialization. PMID:25837659

Cellulose nanomaterials in water treatment technologies.

Science.gov (United States)

Carpenter, Alexis Wells; de Lannoy, Charles-François; Wiesner, Mark R

2015-05-05

Cellulose nanomaterials are naturally occurring with unique structural, mechanical and optical properties. While the paper and packaging, automotive, personal care, construction, and textiles industries have recognized cellulose nanomaterials' potential, we suggest cellulose nanomaterials have great untapped potential in water treatment technologies. In this review, we gather evidence of cellulose nanomaterials' beneficial role in environmental remediation and membranes for water filtration, including their high surface area-to-volume ratio, low environmental impact, high strength, functionalizability, and sustainability. We make direct comparison between cellulose nanomaterials and carbon nanotubes (CNTs) in terms of physical and chemical properties, production costs, use and disposal in order to show the potential of cellulose nanomaterials as a sustainable replacement for CNTs in water treatment technologies. Finally, we comment on the need for improved communication and collaboration across the myriad industries invested in cellulose nanomaterials production and development to achieve an efficient means to commercialization.

Improving yield and composition of protein concentrates from green tea residue in an agri-food supply chain: Effect of pre-treatment

NARCIS (Netherlands)

Zhang, Chen; Krimpen, Van Marinus M.; Sanders, Johan P.M.; Bruins, Marieke E.

2016-01-01

Rather than improving crop-production yield, developing biorefinery technology for unused biomass from the agri-food supply chain may be the crucial factor to reach sustainable global food security. A successful example of food-driven biorefinery is the extraction of protein from green tea residues,

Radioactive material in residues of health services residues

International Nuclear Information System (INIS)

Costa R, A. Jr.; Recio, J.C.

2006-01-01

The work presents the operational actions developed by the one organ responsible regulator for the control of the material use radioactive in Brazil. Starting from the appearance of coming radioactive material of hospitals and clinical with services of nuclear medicine, material that that is picked up and transported in specific trucks for the gathering of residuals of hospital origin, and guided one it manufactures of treatment of residuals of services of health, where they suffer radiological monitoring before to guide them for final deposition in sanitary embankment, in the city of Sao Paulo, Brazil. The appearance of this radioactive material exposes a possible one violation of the norms that govern the procedures and practices in that sector in the country. (Author)

Radiation processing technology for industrial waste water treatment

International Nuclear Information System (INIS)

2011-01-01

Radiation sterilization technology, cross-linked polymers and curing, food and environmental applications of the radiation is widely used for many years. At the same time, drinking water and wastewater treatment are the part of the radiation technology applications. For this purpose, drinking water and wastewater treatment plants in various countries has been established. In this project, gamma / electron beam radiation treatment is intended to be used for the treatment of alkaloid, textiles and polychlorinated biphenyls (PCBs) wastewater. In this regard, the chemical characterization of wastewater, the interaction with radiation, biological treatment and determination of toxicological properties are the laboratory studies milestones. After laboratory studies, the establishment of a pilot scale treatment plant has been planned. Within the framework of the project a series of dye used in textile industry were examined. Besides the irradiation, the changes in treatment efficiency were investigated by using of oxygen and hydrogen peroxide in conjunction with the irradiation. Same working methods were implemented in the wastewater treatment of Bolvadin Opium Alkaloid Factory as well. In addition to chemical analysis in this study, aerobic and anaerobic biological treatment process also have been applied. Standard reference materials has been used for the marine sediment study contaminated with polychlorinated biphenyls.

An overview of the main foodstuff sample preparation technologies for tetracycline residue determination.

Science.gov (United States)

Pérez-Rodríguez, Michael; Pellerano, Roberto Gerardo; Pezza, Leonardo; Pezza, Helena Redigolo

2018-05-15

Tetracyclines are widely used for both the treatment and prevention of diseases in animals as well as for the promotion of rapid animal growth and weight gain. This practice may result in trace amounts of these drugs in products of animal origin, such as milk and eggs, posing serious risks to human health. The presence of tetracycline residues in foods can lead to the transmission of antibiotic-resistant pathogenic bacteria through the food chain. In order to ensure food safety and avoid exposure to these substances, national and international regulatory agencies have established tolerance levels for authorized veterinary drugs, including tetracycline antimicrobials. In view of that, numerous sensitive and specific methods have been developed for the quantification of these compounds in different food matrices. One will note, however, that the determination of trace residues in foods such as milk and eggs often requires extensive sample extraction and preparation prior to conducting instrumental analysis. Sample pretreatment is usually the most complicated step in the analytical process and covers both cleaning and pre-concentration. Optimal sample preparation can reduce analysis time and sources of error, enhance sensitivity, apart from enabling unequivocal identification, confirmation and quantification of target analytes. The development and implementation of more environmentally friendly analytical procedures, which involve the use of less hazardous solvents and smaller sample sizes compared to traditional methods, is a rapidly increasing trend in analytical chemistry. This review seeks to provide an updated overview of the main trends in sample preparation for the determination of tetracycline residues in foodstuffs. The applicability of several extraction and clean-up techniques employed in the analysis of foodstuffs, especially milk and egg samples, is also thoroughly discussed. Copyright © 2018 Elsevier B.V. All rights reserved.

Microbial Community Profiles in Wastewaters from Onsite Wastewater Treatment Systems Technology.

Directory of Open Access Journals (Sweden)

Łukasz Jałowiecki

Full Text Available The aim of the study was to determine the potential of community-level physiological profiles (CLPPs methodology as an assay for characterization of the metabolic diversity of wastewater samples and to link the metabolic diversity patterns to efficiency of select onsite biological wastewater facilities. Metabolic fingerprints obtained from the selected samples were used to understand functional diversity implied by the carbon substrate shifts. Three different biological facilities of onsite wastewater treatment were evaluated: fixed bed reactor (technology A, trickling filter/biofilter system (technology B, and aerated filter system (the fluidized bed reactor, technology C. High similarities of the microbial community functional structures were found among the samples from the three onsite wastewater treatment plants (WWTPs, as shown by the diversity indices. Principal components analysis (PCA showed that the diversity and CLPPs of microbial communities depended on the working efficiency of the wastewater treatment technologies. This study provided an overall picture of microbial community functional structures of investigated samples in WWTPs and discerned the linkages between microbial communities and technologies of onsite WWTPs used. The results obtained confirmed that metabolic profiles could be used to monitor treatment processes as valuable biological indicators of onsite wastewater treatment technologies efficiency. This is the first step toward understanding relations of technology types with microbial community patterns in raw and treated wastewaters.

Management of NORM Residues

International Nuclear Information System (INIS)

2013-06-01

The IAEA attaches great importance to the dissemination of information that can assist Member States in the development, implementation, maintenance and continuous improvement of systems, programmes and activities that support the nuclear fuel cycle and nuclear applications, and that address the legacy of past practices and accidents. However, radioactive residues are found not only in nuclear fuel cycle activities, but also in a range of other industrial activities, including: - Mining and milling of metalliferous and non-metallic ores; - Production of non-nuclear fuels, including coal, oil and gas; - Extraction and purification of water (e.g. in the generation of geothermal energy, as drinking and industrial process water; in paper and pulp manufacturing processes); - Production of industrial minerals, including phosphate, clay and building materials; - Use of radionuclides, such as thorium, for properties other than their radioactivity. Naturally occurring radioactive material (NORM) may lead to exposures at some stage of these processes and in the use or reuse of products, residues or wastes. Several IAEA publications address NORM issues with a special focus on some of the more relevant industrial operations. This publication attempts to provide guidance on managing residues arising from different NORM type industries, and on pertinent residue management strategies and technologies, to help Member States gain perspectives on the management of NORM residues

Identification and assessment of site treatment plan implementation opportunities for emerging technologies

Energy Technology Data Exchange (ETDEWEB)

Bernard, E.A. [Sandia National Labs., Germantown, MD (United States)

1995-12-31

The Department of Energy (DOE), in response to the 1992 Federal Facility Compliance Act, has prepared Site Treatment Plans (STP) for the approximately 2,000 waste streams identified within its mixed waste inventory Concurrently, emerging mixed waste treatment technologies are in final development. This paper defines a three-phase process to identify and assess implementation opportunities for these emerging technologies within the STP. It highlights the first phase, functional matching of expected treatment capabilities with proposed treatment requirements. Matches are based on treatment type, regulated contaminant and waste matrix type, for both capabilities and requirements. Results identify specific waste streams and volumes that could be treated by each emerging technology. A study for Plasma Hearth Process, Delphi DETOX{sup sm}, Supercritical Water Oxidation and Vitrification shows that about 200,000 ml of DOE`s mixed waste inventory can potentially be treated by one or more of these emerging technologies. Actual implementations are small fractions of the treatable inventory. Differences between potential and actual implementations must be minimized to accrue optimum benefit from implementation of emerging or alternative treatment technologies. Functional matching is the first phase in identifying and quantifying benefits, addressing technology system and treatment issues, and providing, in part, the basis for STP implementation decisions. DOE, through EM`s Office of Technology Development, has funded this work.

Isolation of a bacteria of the Bacillus genus as indicator in the disinfection of residual waters by means of the ionizing radiation (e- , γ)

International Nuclear Information System (INIS)

Mata J, M.

2003-01-01

The pollutants of the water can be chemical, physical and biological. Among those biological we find to the microorganisms: bacterias, virus and protozoa. These cause important infections in many countries, mainly of Latin America. With the advance of the technology and the quick demographic growth, the biological pollution of the water has already become an important topic since it would damage the public health and it causes that their disinfection has greater attention. In the treatment of residual waters three basic treatments exist the one primary, secondary and tertiary; in this last we find the disinfection, which can be taken to end by chemical and physical methods. For this work of investigation it was used the ionizing radiation, because it is an innovative technology that it eliminates microorganisms in residual waters. The investigation consisted on treating, samples of residual water after the biological treatment of the plant RECICLAGUA with ionizing radiation (electrons and gammas), for the case of electrons it was used the dose of 0.5 kGy and for gamma the dose, of 5 kGy, later the survivor bacteria was isolated to these doses in both cases and they were carried out the tests of identification. In accordance with the obtained results can say that it is about a B. subtilis. The isolated B.subtilis was presented as a pollutant of the flora of the residual water, having a greater survival to the dose of 0.5 and 5 kGy with electrons and gammas, respectively that other present polluting microorganisms in the samples of residual water. For it fits signalize that this microorganism shows characteristics as it easy isolation and identification, the presence with pathogen microorganisms and a greater survival when being irradiated, therefore it can use as indicator in the disinfection of residual waters through ionizing radiation (electrons and gammas). (Author)

Mixed waste characterization, treatment, and disposal focus area. Technology summary

International Nuclear Information System (INIS)

1995-06-01

This paper presents details about the technology development programs of the Department of Energy. In this document, waste characterization, thermal treatment processes, non-thermal treatment processes, effluent monitors and controls, development of on-site innovative technologies, and DOE business opportunities are applied to environmental restoration. The focus areas for research are: contaminant plume containment and remediation; mixed waste characterization, treatment, and disposal; high-level waste tank remediation; landfill stabilization; and decontamination and decommissioning

Mixed waste characterization, treatment, and disposal focus area. Technology summary

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-06-01

This paper presents details about the technology development programs of the Department of Energy. In this document, waste characterization, thermal treatment processes, non-thermal treatment processes, effluent monitors and controls, development of on-site innovative technologies, and DOE business opportunities are applied to environmental restoration. The focus areas for research are: contaminant plume containment and remediation; mixed waste characterization, treatment, and disposal; high-level waste tank remediation; landfill stabilization; and decontamination and decommissioning.

Application of spent fuel treatment technology to plutonium immobilization

International Nuclear Information System (INIS)

McPheeters, C.C.; Ackerman, J.P.; Gay, E.C., Johnson, G.K.

1996-01-01

The purpose of the electrometallurgical treatment technology being developed at Argonne National Laboratory (ANL) is to convert certain spent nuclear fuels into waste forms that are suitable for disposal in a geological repository for nuclear waste. The spent fuels of interest are those that cannot be safely stored for a long time in their current condition, and those that cannot be qualified for repository disposal. This paper explores the possibility of applying this electrometallurgical treatment technology to immobilization of surplus fissile materials, primarily plutonium. Immobilization of surplus fissile materials by electrometallurgical treatment could be done in the same facilities, at the same time. and in the same equipment as the proposed treatment of the present inventory of spent nuclear fuel. The cost and schedule savings of this simultaneous treatment scheme would be significant

The irradiation as alternative treatment for laboratory wastes; A irradiacao como alternativa de tratamento para residuos de laboratorio

Energy Technology Data Exchange (ETDEWEB)

Borrely, Sueli Ivone; Romanelli, Maria Fernanda; Silva, Giovana Pasqualini da; Castro, Daniela Marques [Instituto de Pesquisas Energeticas e Nucleares (IPEN), Sao Paulo, SP (Brazil)]. E-mail: sborrely@ipen.br

2005-07-01

The irradiation of effluents may be done by electron accelerator or gamma radiation source (cobalt-60). This technology has been developed as an alternative for several contaminants from different processes and sources. This paper shows the results of electron beam applied to liquid laboratories residues (effluents and standard solutions). Radiation doses were determined for the improvement of laboratories residues measured by detoxification of them. New technologies for residues treatment as well as decreasing contaminants generation is essential part of laboratories activities for environmental management for industry, universities and research institutions. (author)

Interaction of acid mine drainage with Ordinary Portland Cement blended solid residues generated from active treatment of acid mine drainage with coal fly ash.

Science.gov (United States)

Gitari, Wilson M; Petrik, Leslie F; Key, David L; Okujeni, Charles

2011-01-01

Fly ash (FA) has been investigated as a possible treatment agent for Acid mine drainage (AMD) and established to be an alternative, cheap and economically viable agent compared to the conventional alkaline agents. However, this treatment option also leads to generation of solid residues (SR) that require disposal and one of the proposed disposal method is a backfill in coal mine voids. In this study, the interaction of the SR with AMD that is likely to be present in such backfill scenario was simulated by draining columns packed with SR and SR + 6% Ordinary Portland Cement (OPC) unsaturated with simulated AMD over a 6 month period. The evolving geochemistry of the liquid/solid (L/S) system was evaluated in-terms of the mineral phases likely or controlling contaminants attenuation at the different pH regimes generated. Stepwise acidification of the percolates was observed as the drainage progressed. Two pH buffer zones were observed (7.5-9 and 3-4) for SR and (11.2-11.3 and 3.5-4) for SR + 6% OPC. The solid residue cores (SR) appeared to have a significant buffering capacity, maintaining a neutral to slightly alkaline pH in the leachates for an extended period of time (97 days: L/S 4.3) while SR + 6% OPC reduced this neutralization capacity to 22 days (L/S 1.9). Interaction of AMD with SR or SR + 6% OPC generated alkaline conditions that favored precipitation of Fe, Al, Mn-(oxy) hydroxides, Fe and Ca-Al hydroxysulphates that greatly contributed to the contaminants removal. However, precipitation of these phases was restricted to the pH of the leachates remaining at neutral to circum-neutral levels. Backfill of mine voids with SR promises to be a feasible technology for the disposal of the SR but its success will greatly depend on the disposal scenario, AMD generated and the alkalinity generating potential of the SR. A disadvantage would be the possible re-dissolution of the precipitated phases at pH water column. However extrapolation of this concept to a field

Technology for commercial radioactive waste management

International Nuclear Information System (INIS)

1979-05-01

Conceptual processes and facilities for treating gaseous and various transuranium (TRU) wastes produced during the past fission portion of the light water reactor fuel cycle are described in volume 2. The goal of the treatment process for TRU wastes and for long-lived radionuclides removed from the gaseous waste streams is to convert these wastes to stable products suitable for placement in geologic isolation repositories. The treatment concepts are based on available technology. They do not necessarily represent an optimum design but are representative of what could be achieved with current technology. In actual applications it is reasonable to expect that there could be some improvement over these concepts that might be reflected in either lower costs or lower environmental impacts or both. These conceptual descriptions do provide a reasonable basis for cost analysis and for development of estimates of environmental impacts. The waste treatment technologies considered here include: high-level waste solidification, packaging of fuel residue, failed equipment and noncombustible waste treatment, general trash and combustible waste treatment, degraded solvent treatment, dilute aqueous waste pretreatment, immobilization of wet and solid wastes, off-gas particle removal systems, fuel reprocessing plant dissolver off-gas treatment, process off-gas treatment, and fuel reprocessing plant atmospheric protection system

Intermittent hormonal therapy in the treatment of post-irradiation residual/recurrent prostate cancer

International Nuclear Information System (INIS)

Williams, Aaron O; Kocherill, Paul G; Wallace, Michelle; Forman, Jeffrey D

1996-01-01

Purpose: To evaluate the efficacy and toxicity of intermittent hormonal therapy in the treatment of residual/recurrent prostate cancer. Materials and Methods: Seventeen patients with biochemical evidence of residual/recurrent prostate cancer were initially treated with radiation therapy (RT)(13), neo-adjuvant hormonal therapy and RT (3), or RT following prostatectomy (1). The mean follow-up time was 19.4 months from the initiation of hormonal therapy. Hormonal therapy consisted of an LH-RH agonist alone (7), an anti-androgen alone (1) or a combination of both (9). Hormonal therapy was continued until the prostatic specific antigen (PSA) level became undetectable. IHT was reinstituted when the PSA reached a pre-determined level, usually greater than or equal to 10ng/ml. Results: The mean time from completion of primary treatment to the initiation of hormonal therapy was 32.5 months. The mean PSA at the start of the first cycle of hormonal therapy was 43.9ng/ml, the second cycle, 11.9ng/ml and the third cycle, 24ng/ml. The mean PSA levels at the end of the first and second cycle of hormonal therapy were .48 and .42ng/ml, respectively. No patient has yet completed the third cycle of hormonal therapy. The average duration of hormonal therapy was 10 months for the first cycle and 4 months for the second cycle. The mean intermittent time off hormones were 9.3 months between cycles 1 and 2, and 10 months between cycles 2 and 3. No patient has yet become refractory to hormonal therapy. Currently all patients are alive. All patients experienced hot flashes and decreased libido at varying degrees during treatment. Thirty-five percent experienced gynecomastia. During the intervals between hormonal therapy, most patients reported a decrease in hot flashes. Conclusion: This analysis supplies preliminary evidence that intermittent hormonal therapy is a viable option in patients with biochemical evidence of disease following initial therapy. It is associated with less treatment

Radioactive waste treatment technology at Czech nuclear power plants

International Nuclear Information System (INIS)

Kulovany, J.

2001-01-01

This presentation describes the main technologies for the treatment and conditioning of radioactive wastes at Czech nuclear power plants. The main technologies are bituminisation for liquid radioactive wastes and supercompaction for solid radioactive wastes. (author)

Carbamazepine as a Possible Anthropogenic Marker in Water: Occurrences, Toxicological Effects, Regulations and Removal by Wastewater Treatment Technologies

Directory of Open Access Journals (Sweden)

Faisal I. Hai

2018-01-01

Full Text Available Carbamazepine (CBZ, a pharmaceutical compound, has been proposed as an anthropogenic marker to assess water quality due to its persistence in conventional treatment plants and widespread presence in water bodies. This paper presents a comprehensive literature review on sources and occurrences of CBZ in water bodies, as well as toxicological effects and regulations of the drug. Given the documented side effects of CBZ on the human body when taken medicinally, its careful monitoring in water is recommended. CBZ residues in drinking water may provide a pathway to embryos and infants via intrauterine exposure or breast-feeding, which may cause congenital malformations and/or neurodevelopmental problems over long term exposure. An in-depth technical assessment of the conventional and advanced treatment technologies revealed the inadequacy of the standalone technologies. Compared to conventional activated sludge and membrane bioreactor processes, effective removal of CBZ can be achieved by nanofiltration and reverse osmosis membranes. However, recent studies have revealed that harsh chemical cleaning, as required to mitigate membrane fouling, can often reduce the long-term removal efficiency. Furthermore, despite the efficient performance of activated carbon adsorption and advanced oxidation processes, a few challenges such as cost of chemicals and regeneration of activated carbon need to be carefully considered. The limitations of the individual technologies point to the advantages of combined and hybrid systems, namely, membrane bioreactor coupled with nanofiltration, adsorption or advanced oxidation process.

Biogas systems for sisal and other agro-industrial residues

Energy Technology Data Exchange (ETDEWEB)

Jungersen, G [Danish Technological Inst., Section for Biotechnology, Taastrup (Denmark)

1998-12-31

Most of the East-African agro-industries are generating very large quantities of organic residues from production and processing of different crops. In the East-African Region the most important of these crops are: Sisal, Sugar, Coffee, Cashew nuts and Pineapple. In other 3. world countries, Palm oil and Cassava (Tapioca starch) processing are main producers of organic waste products. Moreover, large quantities of organic residues are generated from other food processing activities like breweries, consumption of bananas etc. The following pages give examples of setups and system designs of anaerobic treatment systems for some of the residues mentioned above. When considering anaerobic treatment of sisal residues, which constitutes the main agro-industrial biomass resource in Tanzania, two major issues should be considered: Optimal reactor set-up and performance; And optionally, potential methods for pre-treatment of fibre fraction in order to increase the methane yield. The sisal liquid residues are degraded very fast and efficiently in UASB systems. At COD loading rates less than 11 kg COD/m{sup 3} x day, the reduction in organic matter is more than 90% and methane yields obtained are between 373 and 377 ml CH{sub 4}/g COD reduced. The treatment of sisal solid residues in CSTR systems has been examined both at mesophilic (37 deg. C) and thermophilic temperatures (55 deg. C.). (EG)

Biogas systems for sisal and other agro-industrial residues

Energy Technology Data Exchange (ETDEWEB)

Jungersen, G. [Danish Technological Inst., Section for Biotechnology, Taastrup (Denmark)

1997-12-31

Most of the East-African agro-industries are generating very large quantities of organic residues from production and processing of different crops. In the East-African Region the most important of these crops are: Sisal, Sugar, Coffee, Cashew nuts and Pineapple. In other 3. world countries, Palm oil and Cassava (Tapioca starch) processing are main producers of organic waste products. Moreover, large quantities of organic residues are generated from other food processing activities like breweries, consumption of bananas etc. The following pages give examples of setups and system designs of anaerobic treatment systems for some of the residues mentioned above. When considering anaerobic treatment of sisal residues, which constitutes the main agro-industrial biomass resource in Tanzania, two major issues should be considered: Optimal reactor set-up and performance; And optionally, potential methods for pre-treatment of fibre fraction in order to increase the methane yield. The sisal liquid residues are degraded very fast and efficiently in UASB systems. At COD loading rates less than 11 kg COD/m{sup 3} x day, the reduction in organic matter is more than 90% and methane yields obtained are between 373 and 377 ml CH{sub 4}/g COD reduced. The treatment of sisal solid residues in CSTR systems has been examined both at mesophilic (37 deg. C) and thermophilic temperatures (55 deg. C.). (EG)

Use of life cycle assessment as decision-support tool for water reuse and handling of residues at a Danish industrial laundry

DEFF Research Database (Denmark)

Jørgensen, Kim; Villanueva, Alejandro; Wenzel, Henrik

2004-01-01

. Heavy metals originate from the dirt in the workwear that is washed in the laundry. It is further concluded that the studied water treatment technologies satisfy both the need of clean water for recycling and simultaneously help controlling a safe disposal of pollutants by concentration of the residues...

Relatively rapid loss of lampricide residues from fillet tissue of fish after routine treatment

Science.gov (United States)

Vue, C.; Bernardy, J.A.; Hubert, T.D.; Gingerich, W.H.; Stehly, G.R.

2002-01-01

The selective sea lamprey (Petromyzon marinus) larvicide 3-trifluoromethyl-4-nitrophenol (TFM) is currently used to control parasitic sea lampreys in tributaries to the Great Lakes basin. The concentration and persistence of TFM and its major metabolite, TFM glucuronide (TFM-glu), was determined in fillet tissue of fish after a typical stream application. Rainbow trout (Oncorhynchus mykiss) and channel catfish (Ictalurus punctatus) were exposed to a nominal concentration of 12.6 nmol/mL TFM for about 12 h during a sea lamprey control treatment of the Ford River in Michigan. Concentrations of TFM and TFM-glu were greatest in the fillet tissues during the exposure period, with greater residues in channel catfish (wet wt; mean, 6.95 nmol/g TFM; mean, 2.40 nmol/g TFM-glu) than in rainbow trout (wet wt; mean, 1.45 nmol/g TFM; mean, 0.93 nmol/g TFM-glu). After the exposure period, residues in both species decreased by 90-99% within 6-12 h and were less than the quantitation limit (<0.03 nmol/g) within 36 h.

Handling of Solid Residues

International Nuclear Information System (INIS)

Medina Bermudez, Clara Ines

1999-01-01

The topic of solid residues is specifically of great interest and concern for the authorities, institutions and community that identify in them a true threat against the human health and the atmosphere in the related with the aesthetic deterioration of the urban centers and of the natural landscape; in the proliferation of vectorial transmitters of illnesses and the effect on the biodiversity. Inside the wide spectrum of topics that they keep relationship with the environmental protection, the inadequate handling of solid residues and residues dangerous squatter an important line in the definition of political and practical environmentally sustainable. The industrial development and the population's growth have originated a continuous increase in the production of solid residues; of equal it forms, their composition day after day is more heterogeneous. The base for the good handling includes the appropriate intervention of the different stages of an integral administration of residues, which include the separation in the source, the gathering, the handling, the use, treatment, final disposition and the institutional organization of the administration. The topic of the dangerous residues generates more expectation. These residues understand from those of pathogen type that are generated in the establishments of health that of hospital attention, until those of combustible, inflammable type, explosive, radio-active, volatile, corrosive, reagent or toxic, associated to numerous industrial processes, common in our countries in development

Management of municipal solid waste incineration residues

International Nuclear Information System (INIS)

Sabbas, T.; Polettini, A.; Pomi, R.; Astrup, T.; Hjelmar, O.; Mostbauer, P.; Cappai, G.; Magel, G.; Salhofer, S.; Speiser, C.; Heuss-Assbichler, S.; Klein, R.; Lechner, P.

2003-01-01

The management of residues from thermal waste treatment is an integral part of waste management systems. The primary goal of managing incineration residues is to prevent any impact on our health or environment caused by unacceptable particulate, gaseous and/or solute emissions. This paper provides insight into the most important measures for putting this requirement into practice. It also offers an overview of the factors and processes affecting these mitigating measures as well as the short- and long-term behavior of residues from thermal waste treatment under different scenarios. General conditions affecting the emission rate of salts and metals are shown as well as factors relevant to mitigating measures or sources of gaseous emissions

Use of Computer and Mobile Technologies in the Treatment of Depression.

Science.gov (United States)

Callan, Judith A; Wright, Jesse; Siegle, Greg J; Howland, Robert H; Kepler, Britney B

2017-06-01

Major depression (MDD) is a common and disabling disorder. Research has shown that most people with MDD receive either no treatment or inadequate treatment. Computer and mobile technologies may offer solutions for the delivery of therapies to untreated or inadequately treated individuals with MDD. The authors review currently available technologies and research aimed at relieving symptoms of MDD. These technologies include computer-assisted cognitive-behavior therapy (CCBT), web-based self-help, Internet self-help support groups, mobile psychotherapeutic interventions (i.e., mobile applications or apps), technology enhanced exercise, and biosensing technology. Copyright © 2017 Elsevier Inc. All rights reserved.

Residual stress by repair welds

International Nuclear Information System (INIS)

Mochizuki, Masahito; Toyoda, Masao

2003-01-01

Residual stress by repair welds is computed using the thermal elastic-plastic analysis with phase-transformation effect. Coupling phenomena of temperature, microstructure, and stress-strain fields are simulated in the finite-element analysis. Weld bond of a plate butt-welded joint is gouged and then deposited by weld metal in repair process. Heat source is synchronously moved with the deposition of the finite-element as the weld deposition. Microstructure is considered by using CCT diagram and the transformation behavior in the repair weld is also simulated. The effects of initial stress, heat input, and weld length on residual stress distribution are studied from the organic results of numerical analysis. Initial residual stress before repair weld has no influence on the residual stress after repair treatment near weld metal, because the initial stress near weld metal releases due to high temperature of repair weld and then stress by repair weld regenerates. Heat input has an effect for residual stress distribution, for not its magnitude but distribution zone. Weld length should be considered reducing the magnitude of residual stress in the edge of weld bead; short bead induces high tensile residual stress. (author)

Legal aspects of auxillary reproductive technologies in infertility treatment

OpenAIRE

V.Yu. Albitskiy; N.D. Odinayeva; V.O. Mansimova

2011-01-01

The article presents several aspects of legal regulation of auxillary reproductive technologies in treatment of infertility in Russia and other countries.Key words: auxillary reproductive technologies, method of extracorporeal fertilization, newborn, premature newborn, multiple pregnancy, embryo, infertility, law.

Biofuel technologies. Recent developments

Energy Technology Data Exchange (ETDEWEB)

Gupta, Vijai Kumar [National Univ. of Ireland Galway (Ireland). Dept. of Biochemistry; MITS Univ., Rajasthan (India). Dept. of Science; Tuohy, Maria G. (eds.) [National Univ. of Ireland Galway (Ireland). Dept. of Biochemistry

2013-02-01

Written by experts. Richly illustrated. Of interest to both experienced researchers and beginners in the field. Biofuels are considered to be the main potential replacement for fossil fuels in the near future. In this book international experts present recent advances in biofuel research and related technologies. Topics include biomethane and biobutanol production, microbial fuel cells, feedstock production, biomass pre-treatment, enzyme hydrolysis, genetic manipulation of microbial cells and their application in the biofuels industry, bioreactor systems, and economical processing technologies for biofuel residues. The chapters provide concise information to help understand the technology-related implications of biofuels development. Moreover, recent updates on biofuel feedstocks, biofuel types, associated co- and byproducts and their applications are highlighted. The book addresses the needs of postgraduate researchers and scientists across diverse disciplines and industrial sectors in which biofuel technologies and related research and experimentation are pursued.

Carbaryl residues in maize and processed products

International Nuclear Information System (INIS)

Qureshi, M.J.; Sattar, A. Jr.; Naqvi, M.H.

1981-01-01

Carbaryl residues in two local maize varieties were determined using a colorimetric method. No significant differences were observed for residues of the two varieties which ranged between 12.0 to 13.75 mg/kg in the crude oil, and averaged 1.04 and 0.67 mg/kg in the flour and cake respectively. In whole maize plants, carbaryl residues declined to approximately 2 mg/kg 35 days after treatment. Cooking in aqueous, oil or aqueous-oil media led to 63-83% loss of carbaryl residues, after 30 minutes. (author)

The Conversion and Sustainable Use of Alumina Refinery Residues: Global Solution Examples

Science.gov (United States)

Fergusson, Lee

This paper introduces current industry best practice for the conversion of alumina refinery residues (or "red mud") from hazardous waste to benign, inert material. The paper will examine four neutralization methods and Basecon Technology, a sustainable conversion process. The paper will consider ways through which this converted material can be combined and processed for sustainable applications in the treatment of hazardous waste streams (such as industrial wastewater and sludges, biosolids, and CCA wastes), contaminated brownfield sites, and mine site wastes. Recent discoveries and applications, such as the successful treatment of high levels of radium in drinking water in the USA, will also be discussed. Examples of global solutions and their technical merits will be assessed.

Bacillus cereus as indicator in the sterilization of residual water with high energy electrons

International Nuclear Information System (INIS)

Mejia Z, E.

2000-01-01

One of the main causes of water pollution is the presence of microorganisms that provoke infections, moreover of chemical substances. The processes of residual water treatment finally require of the disinfection for its use or final disposition. The radiation technology for the residual water treatment by mean of electron beams is an innovator process because as well as decomposing the chemical substance or to degrade them, also it provokes a disinfection by which this is proposed as alternative for disinfection of residual water, with the purpose in reusing the water treated in the agriculture, recreation and industry among others secondary activities, solving environmental or health problems. The objective of this work is to evaluate the use of Bacillus cereus as biological indicator in the disinfection by radiation, using High Energy Electrons. To fulfil with this objective, the work was developed in three stages, the first one consisted in the acquisition, propagation and conservation of the Bacillus cereus stumps, considering Escherichia coli and Salmonella typhimurium as pathogenic germs present in residual water. Moreover, the inocule standardization and the conditions of the Electron accelerator Type Pelletron. In the second stage it was performed the irradiation of aqueous samples of the microorganisms simulating biological pollution and the application to problem samples of a treatment plant sited in the Lerma River zone of mixed residual water. And in the third stage was performed a regression analysis to the reported survival for each kind of microorganisms. The results obtained show that with the use of Electron beams was reduced 6 logarithmic units de E. coli at 129 Gy, for S. typhimurium it was reduced 8 logarithmic units at 383 Gy and the B. cereus at 511 Gy was reduced 6.8 logarithmic units. Of the problem samples irradiated at 500 Gy, the concentration of the total account diminished from 8.70 x 10 7 UFC/ml to 550 UFC/ml, the presence of B. Cereus

Multi-Criteria Sustainability Assessment of Urban Sludge Treatment Technologies

DEFF Research Database (Denmark)

An, Da; Xi, Beidou; Ren, Jingzheng

2017-01-01

to determine the weights of the criteria for sustainability assessment, and extension theory was used to prioritize the alternative technologies for the treatment of urban sewage sludge and grade their sustainability performances. An illustrative case including three technologies (compositing, incineration...

Legal aspects of auxillary reproductive technologies in infertility treatment

Directory of Open Access Journals (Sweden)

V.Yu. Albitskiy

2011-01-01

Full Text Available The article presents several aspects of legal regulation of auxillary reproductive technologies in treatment of infertility in Russia and other countries.Key words: auxillary reproductive technologies, method of extracorporeal fertilization, newborn, premature newborn, multiple pregnancy, embryo, infertility, law.

Aluminum-based water treatment residual use in a constructed wetland for capturing urban runoff phosphorus: Column study

Science.gov (United States)

Aluminum-based water treatment residuals (Al-WTR) have a strong affinity to sorb phosphorus. In a proof-of-concept greenhouse column study, Al-WTR was surface-applied at 0, 62, 124, and 248 Mg/ha to 15 cm of soil on top of 46 cm of sand; Al-WTR rates were estimated to capture 0, 10, 20, and 40 year...

Electrodialytic remediation of municipal solid waste incineration residues using different membranes

DEFF Research Database (Denmark)

Parés Viader, Raimon; Jensen, Pernille Erland; Ottosen, Lisbeth M.

2017-01-01

In the present work, three different commercial membrane brands were used in an identical electrodialytic cell setup and operating conditions, in order to reduce the leaching of metals and salt anions of two types of municipal solid waste incineration residues: air pollution control residues...... as a technology to upgrade municipal solid waste incineration residues....

Replacement of 5% of OPC by fly ash and APC residues from MSWI with electrodialytic pre-treatment

DEFF Research Database (Denmark)

Magro, Cátia; Kirkelund, Gunvor Marie; Guedes, Paula

2016-01-01

as pre-treatment prior to incorporation in mortar, aiming to stabilize and remove HM and chlorides. Eight ED experiments were performed for 7 days with a L/S ratio of 3.5. The number of compartments (2 or 3) and current density (0.1 or 1.0 mA cm-2) varied. After ED treatment the heavy metals left...... in the ash were not leached to the same extent as in the original ash. In mortar 5% of Ordinary Portland Cement was replaced by FA and APC residues (raw and ED upgraded). The studied parameters: compressive strength, HM leachability, and Cl content. The ED pre-treatment resulted in a decrease in both...

Evaluation of mechanical vibration effect on the residual stresses levels in steel welded joints using an Interface Matlab based on Norm API 579

Directory of Open Access Journals (Sweden)

R Rodrigues

2016-10-01

Full Text Available Nowadays with the high growth of petrochemical welding technology a great development due to high manufacturing offshore structures, storage tanks of petroleum, boilers and pressure vessels for refining plants have been done. Due to various metallurgical changes and restrictions to contraction and expansion undergone by materials when subjected to welding thermal cycle, internal stresses are generated in welded joint which are nominated residual stresses. It is generally undesirable because it can lead to several problems, such as cracks, cold stress fracture, stress corrosion, among others. Although several studies involving residual stresses have been developed in recent years, few information about the variation of the residual stresses level in welded joints when subjected to stress relief treatment by mechanical vibration have been done. Likewise, there are few information related to the comparison between the degree of efficiency by using the post-weld heat treatment and those treatment. Therefore, the goal of this work was to apply the relieve residual stresses treatment by mechanical vibration in steel welded joints used in oil industry, and compare the results with those obtained by post heat treatment and evaluate the efficiency level of this technique In addition, this works also hope to contribute for a better understanding of this technique and to find which parameters have a greater influence on the results.

Nanofiltration technology in water treatment and reuse: applications and costs.

Science.gov (United States)

Shahmansouri, Arash; Bellona, Christopher

2015-01-01

Nanofiltration (NF) is a relatively recent development in membrane technology with characteristics that fall between ultrafiltration and reverse osmosis (RO). While RO membranes dominate the seawater desalination industry, NF is employed in a variety of water and wastewater treatment and industrial applications for the selective removal of ions and organic substances, as well as certain niche seawater desalination applications. The purpose of this study was to review the application of NF membranes in the water and wastewater industry including water softening and color removal, industrial wastewater treatment, water reuse, and desalination. Basic economic analyses were also performed to compare the profitability of using NF membranes over alternative processes. Although any detailed cost estimation is hampered by some uncertainty (e.g. applicability of estimation methods to large-scale systems, labor costs in different areas of the world), NF was found to be a cost-effective technology for certain investigated applications. The selection of NF over other treatment technologies, however, is dependent on several factors including pretreatment requirements, influent water quality, treatment facility capacity, and treatment goals.

Methods of measuring residual stresses in components

International Nuclear Information System (INIS)

Rossini, N.S.; Dassisti, M.; Benyounis, K.Y.; Olabi, A.G.

2012-01-01

Highlights: ► Defining the different methods of measuring residual stresses in manufactured components. ► Comprehensive study on the hole drilling, neutron diffraction and other techniques. ► Evaluating advantage and disadvantage of each method. ► Advising the reader with the appropriate method to use. -- Abstract: Residual stresses occur in many manufactured structures and components. Large number of investigations have been carried out to study this phenomenon and its effect on the mechanical characteristics of these components. Over the years, different methods have been developed to measure residual stress for different types of components in order to obtain reliable assessment. The various specific methods have evolved over several decades and their practical applications have greatly benefited from the development of complementary technologies, notably in material cutting, full-field deformation measurement techniques, numerical methods and computing power. These complementary technologies have stimulated advances not only in measurement accuracy and reliability, but also in range of application; much greater detail in residual stresses measurement is now available. This paper aims to classify the different residual stresses measurement methods and to provide an overview of some of the recent advances in this area to help researchers on selecting their techniques among destructive, semi destructive and non-destructive techniques depends on their application and the availabilities of those techniques. For each method scope, physical limitation, advantages and disadvantages are summarized. In the end this paper indicates some promising directions for future developments.

DOE evaluates nine alternative thermal technologies for treatment of mixed waste

International Nuclear Information System (INIS)

Anon.

1995-01-01

In June 1993, the U.S. Department of Energy's (DOE's) Office of Technology Development commissioned a study to evaluate 19 thermal technologies for treating DOE's mixed waste. The study was divided into two phases: Phase I evaluated ten conventional incineration techniques (primarily rotary kiln), and Phase II looked at nine innovative, alternative thermal treatment technologies. The treatment processes were evaluated as part of an integrated waste treatment system, which would include all of the facilities, equipment, and methods required to treat and dispose DOE mixed waste. The relative merits and life-cycle costs were then developed for each of the 19 waste treatment systems evaluated. The study also identified the additional research and development, demonstration, and testing/evaluation steps that would be necessary for the waste treatment systems to successfully treat DOE mixed waste. 3 tabs., 2 refs

Treatment of hazardous and toxic liquids using Rochem Disc Tube technology

International Nuclear Information System (INIS)

LaMonica, D.

1992-01-01

Rochem Separation Systems, established in 1990 as a subsidiary of the international Rochem Group, has advanced the treatment of hazardous and toxic liquids with its unique, patented Disc Tube technology. Developed in 1987 at Rochem's design and production facilities in Hamburg, Germany, the Disc Tube technology is a series of membrane modules that greatly reduce the problems that hamper the effectiveness of other treatment technologies (i.e. fouling, scaling, cost, etc.). Applications of the Disc Tube technology include reverse osmosis and ultrafiltration. Rochem was recently accepted into the EPA Superfund Site program as a result of its Disc Tube technology. 1 fig., 1 tab

Temperature Field Prediction for Determining the Residual Stresses Under Heat Treatment of Aluminum Alloys

Directory of Open Access Journals (Sweden)

A. V. Livshits

2014-01-01

Full Text Available The article is devoted to non-stationary temperature field blanks from aluminum alloys during heat treatment. It consists of the introduction and two smaller paragraphs. In the introduction the author concerns the influence of residual stresses arising in the manufacturing process of details, on the strength of the whole aircraft construction and, consequently, on their technical and economic parameters, such as weight, reliability, efficiency, and cost. He also notes that the residual stresses appeared during the production of parts change their location, size and direction under the influence of the elastic deformations that occur during the exploitation of aircraft. Redistributed residual stresses may have a chaotic distribution that may cause overlap of these stresses on the stresses caused by the impact of workload of constructions and destruction or damage of aircraft components.The first paragraph is devoted to the existing methods and techniques for determining the residual stresses. The presented methods and techniques are analyzed to show the advantages and disadvantages of each of them. The conclusion is drawn that the method to determine the residual stresses is necessary, its cost is less than those of existing ones, and an error does not exceed 10%.In the second section, the author divides the problem of determining the residual stresses into two parts, and describes the solution methods of the first one. The first problem is to define the temperature field of the work piece. The author uses a Fourier equation with the definition of initial and boundary conditions to describe a mathematical model of the heat cycle of work piece cooling. He draws special attention here to the fact that it is complicated to determine the heat transfer coefficient, which characterizes the process of cooling the work piece during hardening because of its dependence on a number of factors, such as changing temperature-dependent material properties of

Cervical Precancer Treatment in Low- and Middle-Income Countries: A Technology Overview

Directory of Open Access Journals (Sweden)

Mauricio Maza

2017-08-01

Full Text Available Cervical cancer is the fourth leading cause of cancer-related death in women worldwide, with 90% of cases occurring in low- and middle-income countries (LMICs. There has been a global effort to increase access to affordable screening in these settings; however, a corresponding increase in availability of effective and inexpensive treatment modalities for ablating or excising precancerous lesions is also needed to decrease mortality. This article reviews the current landscape of available and developing technologies for treatment of cervical precancer in LMICs. At present, the standard treatment of most precancerous lesions in LMICs is gas-based cryotherapy. This low-cost, effective technology is an expedient treatment in many areas; however, obtaining and transporting gas is often difficult, and unwieldy gas tanks are not conducive to mobile health campaigns. There are several promising ablative technologies in development that are gasless or require less gas than conventional cryotherapy. Although further evaluation of the efficacy and cost-effectiveness is needed, several of these technologies are safe and can now be implemented in LMICs. Nonsurgical therapies, such as therapeutic vaccines, antivirals, and topical applications, are also promising, but most remain in early-stage trials. The establishment of evidence-based standardized protocols for available treatments and the development and introduction of novel technologies are necessary steps in overcoming barriers to treatment in LMICs and decreasing the global burden of cervical cancer. Guidance from WHO on emerging treatment technologies is also needed.

Predicting the residual life of plant equipment - Why worry

International Nuclear Information System (INIS)

Jaske, C.E.

1985-01-01

Predicting the residual life of plant equipment that has been in service for 20 to 30 years or more is a major concern of many industries. This paper reviews the reasons for increased concern for residual-life assessment and the general procedures used in performing such assessments. Some examples and case histories illustrating procedures for assessing remaining service life are discussed. Areas where developments are needed to improve the technology for remaining-life estimation are pointed out. Then, some of the critical issues involved in residual-life assessment are identified. Finally, the future role of residual-life prediction is addressed

Risk assessments of innovative technologies for treatment of mixed waste

International Nuclear Information System (INIS)

Ragaini, R.C.; Aycock, M.T.; Russell, J.E.

1993-01-01

The mission of the US Department of Energy's (DOE'S) Mixed Waste Integrated Program (MWIP) is to develop complete and appropriate technologies for the treatment of DOE mixed low-level waste and transuranic wastes in order to ensure that all affected DOE installations and projects can come into compliance with environmental law and meet DOE's 30-yr cleanup and operational goals. The MWIP will achieve its goal by developing technologies that are in compliance with regulatory requirements, are socially and politically viable, and are cost beneficial and effective in disposed waste source term and volume reduction. The project management plan for MWIP requires that technologies be evaluated in accordance with criteria that rank technologies with regard to performance, risk, and cost-effectiveness. This paper addresses the methodology used to rank alternative mixed-water treatment technologies with regard to relative risk

Characterization of residues from thermal treatment of treated wood and extraction of Cu, Cr, As and Zn

DEFF Research Database (Denmark)

Ottosen, Lisbeth M.; Pedersen, Anne Juul; Christensen, Iben Vernegren

2005-01-01

, that the charcoal contained a high concentration of Zn, probably from paint. Chemical extraction experiments in HNO were conducted with the charcoal and it was found that the order of extraction (in percentage) was Zn > Cu > As > Cr. A SEM/EDX investigation of the mixed ash from combustion showed the presence...... a matter to cope with when methods to avoid As emission are implemented: the residues with increased concentrations of Cu, Cr and As. In the present paper two different residues after thermal treatment are characterized: a mixed bottom and fly ash from combustion of CCA impregnated wood, and a charcoal...... form in a small layer on the surface of some matrix particles indicating condensation of volatile Cu species. Chemical extraction with inorganic acids showed the order of percentages mobilized as: As > Cu > Cr....

Reactive barrier technologies for treatment of contaminated groundwater at Rocky Flats

International Nuclear Information System (INIS)

Marozas, D.C.; Bujewski, G.E.; Castaneda, N.

1997-01-01

The U.S. Department of Energy (DOE) Office of Science and Technology Subsurface Contaminants Focus Area is supporting the investigation of reactive barrier technologies to mitigate the risks associated with mixed organic/radioactive waste at several DOE sites. Groundwater from a small contaminated plume at the Rocky Flats Environmental Technology Site (RFETS) is being used to evaluate passive reactive material treatment. Permeable reactive barriers which intercept contaminants and destroy the VOC component while containing radionuclides are attractive for a number of reasons relating to public and regulatory acceptance. In situ treatment keeps contaminants away from the earth's surface, there is no above-ground treatment equipment that could expose workers and the public and operational costs are expected to be lower than currently used technologies. This paper will present results from preliminary site characterization and in-field small-scale column testing of reactive materials at RFETS. Successful demonstration is expected to lead to full-scale implementation of the technology at several DOE sites, including Rocky Flats

Treatment technology of low concentration uranium-bearing wastewater and its research progress

International Nuclear Information System (INIS)

Wei Guangzhi; Xu Lechang

2007-01-01

With growth of the discharged uranium-bearing wastewater capacity, a low cost and effective treatment technology is required to avoid transferring and diffusion of the radioactive nuclides. On the basis of analyses of the source and characteristics of the low-concentration uranium-bearing wastewater, the conventional treatment technologies, such as, flocculating settling, ion exchange, concentration, adsorption, and some innovatory technologies, such as, membrane, microorganism, phytoremediation and zero-valent iron technology are introduced. (authors)

Efficacy of residual bifenthrin applied to landscape vegetation against Aedes albopictus.

Science.gov (United States)

Doyle, Melissa A; Kline, Daniel L; Allan, Sandra A; Kaufman, Phillip E

2009-06-01

The daytime biting mosquito Aedes albopictus is a nuisance pest commonly found in suburban yards. The recommended course of treatment for Ae. albopictus is to keep yards free of water-holding containers; however, infestations may require additional control methods such as residual pesticide applications to vegetation. Five plants commonly found in yards or in uncultivated areas in Gainesville, FL were chosen as substrates for evaluation of the effectiveness of residual bifenthrin against 5-7-day-old female Ae. albopictus. Knockdown of mosquitoes after 1 h of exposure was highest the day of and 7 days after treatment. Plant species clearly impacted the effectiveness of residual bifenthrin. One-hour knockdown 7 days after treatment remained high (>62%) only on azalea and holly bush vegetation. Knockdown counts 24 h after exposure demonstrated that residual efficacy of bifenthrin was highest on azalea, with >77% mortality for up to 35 days. Additional bioassays revealed significant differences in the knockdown rates of male, female, gravid, and blood-fed Ae. albopictus exposed to residual bifenthrin treatments, with the highest knockdown observed on the day of and 7 days after treatment.

New aspects of sewerage and water technology

International Nuclear Information System (INIS)

Niemczynowics, J.

1993-01-01

Highly developed countries with expensive water-related infrastructure, sophisticated waterworks and treatment plants, still contribute to local and global pollution. Many developing countries still lack water-treatment facilities and environmentally-sound water management. These problems are especially accentuated in some of the large and fast growing cities of the world. Means of solving the problems involve a new holistic approach to resource management. The goal of such an approach is to close the cycles of residuals that damage the environment, and to recover resources lost in residuals emitted from human activities. The most important step is to apply pollution prevention, i.e. pollution control at the source. Present knowledge suggests technologies that can solve the problem of pollution from human settlements on a single-house level. Alternatively, wastewater may be treated locally and reused. Ecologically-sound technologies that already exist should be used whenever possible. Water management can be integrated with management of other human activities, such as waste handling, industrial production, transportation, etc. Tools for implementation of such solutions are: legislation coupled with education programs; changing competition rules of the market economy; i.e. developing a sustainable society through resource recovery and reuse. Demonstration projects, in which the rules of preventive approach and novel technology are applied, may constitute a practical means of implementing such an approach. 34 refs, 3 figs

Incorporation of feasibility study of residue thin kaolin in of porcelain formulations production

International Nuclear Information System (INIS)

Almeida, V.S. de; Ferreira, E.C.; Oliveira, T.M. de; Freitas, K.D. de Araujo; Soares Filho, J.E.; Sousa, F.J.P. de

2016-01-01

The porcelain is the more advanced product among traditional ceramics due to the high technology used in its manufacture and its excellent technological and aesthetic properties. Due to the continuing worldwide development, kaolin processing industries have increased their productivity and consequently generating large amounts of waste, contributing to environmental degradation. Studies are being conducted to analyze the incorporation of such wastes in the ceramic mass compositions. The objective of this study was to evaluate 4 formulations of porcelain as the possibility of using waste coming from the last stage of kaolin processing. Processing occurred by wet grinding process, with uniaxial compacting pressure of 45 MPa after heat treatment at 1250 ° C. Technological tests were carried out physical and mechanical product. The results showed that the addition of fine kaolin residue was presented as an efficient alternative for the porcelain industry. (author)

Utilization of communication technology by patients enrolled in substance abuse treatment.

Science.gov (United States)

McClure, Erin A; Acquavita, Shauna P; Harding, Emily; Stitzer, Maxine L

2013-04-01

Technology-based applications represent a promising method for providing efficacious, widely available interventions to substance abuse treatment patients. However, limited access to communication technology (i.e., mobile phones, computers, internet, and e-mail) could significantly impact the feasibility of these efforts, and little is known regarding technology utilization in substance abusing populations. A survey was conducted to characterize utilization of communication technology in 266 urban, substance abuse treatment patients enrolled at eight drug-free, psychosocial or opioid-replacement therapy clinics. Survey participants averaged 41 years of age and 57% had a yearly household income of less than $15,000. The vast majority reported access to a mobile phone (91%), and to SMS text messaging (79%). Keeping a consistent mobile phone number and yearly mobile contract was higher for White participants, and also for those with higher education, and enrolled in drug-free, psychosocial treatment. Internet, e-mail, and computer use was much lower (39-45%), with younger age, higher education and income predicting greater use. No such differences existed for the use of mobile phones however. Concern regarding the digital divide for marginalized populations appears to be disappearing with respect to mobile phones, but still exists for computer, internet, and e-mail access and use. Results suggest that mobile phone and texting applications may be feasibly applied for use in program-client interactions in substance abuse treatment. Careful consideration should be given to frequent phone number changes, access to technology, and motivation to engage with communication technology for treatment purposes. Copyright © 2012 Elsevier Ireland Ltd. All rights reserved.

Persistence of pirimiphos methyl residues in stored wheat

International Nuclear Information System (INIS)

Zennouche, B.; Bennaceur, M.

1991-03-01

The persistence of 14C pirimiphos methyl in stored wheat was investigated under local conditions during a storage period of 6 months. Surface, methanol extractable and bound residues were quantified. There was a gradual increase in the surface residues over the storage period. 27,97% of the applied amount was found in the surface residues and 54,16% in the extractable and bound residues one month after treatment. After 6 months storage, about 17,8% of the total quantity of the applied pirimiphos methyl remained on the surface and about 58,6% was present in the grains (extractable and bound residues). During cooking 10,91% of the extractable and bound residues were lost

Selection criteria for wastewater treatment technologies to protect drinking water.

Science.gov (United States)

von Sperling, M

2000-01-01

The protection of water bodies used as sources for drinking water is intimately linked to the adoption of adequate technologies for the treatment of the wastewater generated in the catchment area. The paper presents a general overview of the main technologies used for the treatment of domestic sewage, with a special emphasis on developing countries, and focussing on the main parameters of interest, such as BOD, coliforms and nutrients. A series of tables, figures and charts that can be used for the preliminary selection of treatment technologies is presented. The systems analysed are: stabilisation ponds, activated sludge, trickling filters, anaerobic systems and land disposal. Within each system, the main process variants are covered. Two summary tables are presented, one for quantitative analysis, including easily usable information based on per capita values (US$/cap, Watts/cap, m2 area/cap, m3 sludge/cap), and another for a qualitative comparison among the technologies, based on a one-to-five-star scoring system. The recent trend in tropical countries in the use of UASB (Upflow Anaerobic Sludge Blanket) reactors is also discussed.

Process water treatment in Canada's oil sands industry : 2 : a review of emerging technologies

International Nuclear Information System (INIS)

Allen, E.W.

2008-01-01

This review was conducted to identify candidate treatment technologies for treating oil sands process water. The oil sands industry in Canada uses large volumes of fresh water in order to extract bitumen deposits. The development of process water treatment technologies has become a critical issue for the industry, particularly as oil sand production is expected to triple in the next decade. However, treatment technologies must be adapted to consider the fouling potential of bitumens and fine clays as well as the effect of alkaline process water on treatment performance. The review included developments in chemical modifications to membranes and adsorbents designed to improve pollutant removal and reduce fouling; hybridization technologies designed to enhance the biological treatment of toxic feedwaters; recent advances in photocatalytic oxidation technologies for organic compounds; and new designs for large-scale treatment wetlands for polluted waste waters. It was concluded that major knowledge gaps must be optimized and preliminary studies must be conducted in order to understand how the treatment technologies will be affected by the chemical and physical characteristics of oil sands process water. 188 refs., 8 tabs

Determination of residual 4'-aminomethyl-4,5',8-trimethylpsoralen and mutagenicity testing following psoralen plus UVA treatment of platelet suspensions

International Nuclear Information System (INIS)

Wagner, S.J.; Robinette, D.; Dodd, R.Y.; White, R.; Wolf, L.; Chapman, J.; Lawlor, T.E.

1993-01-01

Psoralens and UVa light have been used in the laboratory to study the inactivation of viruses that may be infrequently present in platelet concentrates prepared for transfusion. In order to evaluate safety aspects of the treatment of platelet suspensions with 4'-aminomethyl-4,5'8-trimethylpsoralen (AMT), the authors have investigated the residual levels and mutagenic potential of AMT after UVA phototreatment. The results suggest that residual available AMT is mutagenic in the AMES test and that the observed frameshift mutations may be caused by binding of AMt or its metabolites to nucleic acids in the absence of UVA light. (Author)

[Evaluation of treatment technology of odor pollution source in petrochemical industry].

Science.gov (United States)

Mu, Gui-Qin; Sui, Li-Hua; Guo, Ya-Feng; Ma, Chuan-Jun; Yang, Wen-Yu; Gao, Yang

2013-12-01

Using an environmental technology assessment system, we put forward the evaluation index system for treatment technology of the typical odor pollution sources in the petroleum refining process, which has been applied in the assessment of the industrial technology. And then the best available techniques are selected for emissions of gas refinery sewage treatment plant, headspace gas of acidic water jars, headspace gas of cold coke jugs/intermediate oil tank/dirty oil tank, exhaust of oxidative sweetening, and vapors of loading and unloading oil.

Thermal treatment of stabilized air pollution control residues in a waste incinerator pilot plant. Part 2: Leaching characteristics of bottom ashes.

Science.gov (United States)

Baun, Dorthe L; Christensen, Thomas H; Bergfeldt, Brita; Vehlow, Jürgen; Mogensen, Erhardt P B

2004-02-01

With the perspective of generating only one solid residue from waste incineration, co-feeding of municipal solid waste and air pollution control residues stabilized by the Ferrox process was investigated in the TAMARA pilot plant incinerator as described in Bergfeldt et al. (Waste Management Research, 22, 49-57, 2004). This paper reports on leaching from the combined bottom ashes. Batch leaching test, pH-static leaching tests, availability tests and column leaching tests were used to characterize the leaching properties. The leaching properties are key information in the context of reuse in construction or in landfilling of the combined residue. In general, the combined bottom ashes had leaching characteristics similar to the reference bottom ash, which contained no APC residue. However, As and Pb showed slightly elevated leaching from the combined bottom ashes, while Cr showed less leaching. The investigated combined bottom ashes had contents of metals comparable to what is expected at steady state after continuous co-feeding of APC residues. Only Cd and Pb were partly volatilized (30-40%) during the incineration process and thus the combined bottom ashes had lower contents of Cd and Pb than expected at steady state. Furthermore, a major loss of Hg was, not surprisingly, seen and co-feeding of Ferrox-products together with municipal solid waste will require dedicated removal of Hg in the flue gas to prevent a build up of Hg in the system. In spite of this, a combined single solid residue from waste incineration seems to be a significant environmental improvement to current technology.

Dry storage technologies: Optimized solutions for spent fuels and vitrified residues

International Nuclear Information System (INIS)

Roland, Vincent; Verdier, Antoine; Sicard, Damien; Neider, Tara

2006-01-01

ancillary equipment, Ready to move to final or centralized repository or reprocessing facility or other ISFSI, Compact systems, Easy rearrangement, Easy handling; - In favor of concrete shielded canisters based systems: Economics when initial quantity is sufficient to spread out up front equipment investment significant cost - Shielding advantage, Easy local production of the relatively light canisters. Both approaches of dry storage technologies can have a positive impact on their public acceptance because of their non-permanent characteristics and because their transport license refers to internationally recognized rules, standards and methods. Currently, more than 1,000 COGEMA Logistics/Transnuclear Inc. dry storage systems have been ordered in Belgium, Germany, Japan, Switzerland, Armenia and the US. Because of the evolution of burnup of spent fuel to be reprocessed, the high activity vitrified residues cannot be transported in the existing cask designs presently used. Therefore, COGEMA LOGISTICS has decided in the late nineties to develop a brand new design of casks with optimized capacity able to store and transport the most active and hottest canisters: the TN TM 81 casks currently in use in Switzerland and the TN TM 85 cask which shall permit in the near future in Germany the storage and the transport of the most active vitrified residues. The TN TM 81 and the TN TM 85 casks have been designed to fully anticipate shipment constraints of the present vitrified residue production in existing reprocessing facilities. They also used the feedback of current shipments and the operational constraints and experience of receiving and shipping facilities. The casks had to fit as much as possible in the existing procedures for the already existing casks such as the TN TM 28 cask and TS 28 V cask, all along the logistics chain of loading, unloading, transport and maintenance. In addition, years of feedback and experience in design and operations - together with ever improved

Decision making tools for selecting sustainable wastewater treatment technologies in Thailand

Science.gov (United States)

Wongburi, Praewa; Park, Jae K.

2018-05-01

Wastewater consists of valuable resources that could be recovered or reused. Still it is under threat because of ineffective wastewater management and systems. In Thailand, less than 25% of wastewater generated may be treated while then rest is inadequately treated and sent back directly into waterbodies or the environment. Furthermore, the technologies that have been applied may be inefficient and unsustainable. Efficiency, sustainability, and simplicity are important concepts when designing an appropriate wastewater treatment system in developing countries. The objectives of this study were to review and evaluate wastewater treatment technologies and propose a method to improve or select an appropriate technology. An expert system in Excel® program was developed to determine the best solution. Sensitivity analysis was applied to compare and assess uncertainty factors. Due to the different conditions of each area, the key factor of interest was varied. Furthermore, Robust Decision Making tool was applied to determine the best way to improve existing wastewater treatment facility and to choose the most appropriate wastewater treatment technology.

Influence of technological treatments on bacterial communities in ...

African Journals Online (AJOL)

Influence of technological treatments on bacterial communities in tilapia ( Oreochromis niloticus ) as determined by 16S rDNA fingerprinting using polymerase chain reaction-denaturing gradient gel electrophoresis (PCR-DGGE)

Development of irradiation technique on degradation residue of pesticide veterinary drugs and mycotoxins in food

International Nuclear Information System (INIS)

He Jiang; Huang Min; Chen Hao; Wu Ling; Gao Peng; Wang Yan; Lei Qing

2011-01-01

Irradiation technology is a new processing technology, It was widely used in food, medicines and medical supplies, chemical and other industries. In this paper, illustrated their applications in the degradation of pesticides, veterinary drugs and mycotoxins aspects residual pollution in food. Analysis of residual contaminants in food irradiation control study limitations and look forward to the prospect of food irradiation technology. (authors)

Advances in HTGR spent fuel treatment technology

International Nuclear Information System (INIS)

Holder, N.D.; Lessig, W.S.

1984-08-01

GA Technologies, Inc. has been investigating the burning of spent reactor graphite under Department of Energy sponsorship since 1969. Several deep fluidized bed burners have been used at the GA pilot plant to develop graphite burning techniques for both spent fuel recovery and volume reduction for waste disposal. Since 1982 this technology has been extended to include more efficient circulating bed burners. This paper includes updates on high-temperature gas-cooled reactor fuel cycle options and current results of spent fuel treatment testing for fluidized and advanced circulating bed burners

Residual stresses around Vickers indents

International Nuclear Information System (INIS)

Pajares, A.; Guiberteau, F.; Steinbrech, R.W.

1995-01-01

The residual stresses generated by Vickers indentation in brittle materials and their changes due to annealing and surface removal were studied in 4 mol% yttria partially stabilized zirconia (4Y-PSZ). Three experimental methods to gain information about the residual stress field were applied: (i) crack profile measurements based on serial sectioning, (ii) controlled crack propagation in post indentation bending tests and (iii) double indentation tests with smaller secondary indents located around a larger primary impression. Three zones of different residual stress behavior are deduced from the experiments. Beneath the impression a crack free spherical zone of high hydrostatic stresses exists. This core zone is followed by a transition regime where indentation cracks develop but still experience hydrostatic stresses. Finally, in an outward third zone, the crack contour is entirely governed by the tensile residual stress intensity (elastically deformed region). Annealing and surface removal reduce this crack driving stress intensity. The specific changes of the residual stresses due to the post indentation treatments are described and discussed in detail for the three zones

Treatment of waste incinerator air-pollution-control residues with FeSO4: Laboratory investigation of design parameters

DEFF Research Database (Denmark)

Jensen, Dorthe Lærke; Christensen, Thomas Højlund; Lundtorp, Kasper

2002-01-01

supplied, the liquid-to-solid ratio of the process, the separation of solids and wastewater, the sequence of material mixing, the possibilities of reuse of water, the feasibility of using secondary (brackish) water, and simple means to improve the wastewater quality. The investigation showed...... that an optimum process configuration could be obtained yielding a stabilised solid product with low leaching of heavy metals and a dischargable wastewater with high contents of salts (in order to remove salts from the solid product) and low concentrations of heavy metals. The amount of iron added to the APC......The key design parameters of a new process for treatment of air-pollution-control (APC) residues (the Ferroxprocess) were investigated in the laboratory. The optimisation involved two different APC-residues from actual incinerator plants. The design parameters considered were: amount of iron oxide...

Development of treatment technologies of the processing of U.S. Department of Energy mixed waste

International Nuclear Information System (INIS)

Backus, P.M.; Berry, J.B.; Coyle, G.J. Jr.; Lurk, P.; Wolf, S.M.

1994-01-01

Waste contaminated with chemically hazardous and radioactive species is defined as mixed waste. Significant technology development has been conducted for separate treatment of hazardous and radioactive waste, but technology development addressing mixed-waste treatment has been limited. In response to the need for a comprehensive and consistent approach to mixed-waste technology development, the Office of Technology Development of the US Department of Energy (DOE) has established the Mixed Waste Integrated Program. The program is identifying and evaluating treatment technologies to treat present and estimated future mixed wastes at DOE sites. The status of the technical initiatives in chemical/physical treatment, waste destruction/stabilization technology, off-gas treatment, and final waste form production/assessment is described in this paper

Evaluation of metals and radionuclides in water treatment system for drinking in Pernambuco state, Brazil

International Nuclear Information System (INIS)

Albuquerque, Adriana Muniz de Almeida

2017-01-01

The metals and radionuclides are naturally incorporated into natural waters, and may be present at levels that condition the health of the population. In view of this, health agencies regulate standards which determine maximum concentration values for these elements in water intended for human consumption. However, the water sources do not have the required quality and the application of treatment technologies is necessary. These technologies remove the impurities initially incorporated into the waters of the fountains from the application of physical and chemical processes. The impurities are retained and concentrated in the treatment systems giving rise to a residue which may contain appreciable concentrations of metals and radionuclides, and this residue is included among the United States Environmental Protection Agency (USEPA). In the present study, the investigation of raw, treated and wastewater samples from 19 Water Treatment Stations located in the state of Pernambuco, in relation to the behavior of Al, Cd, Cu, Cr, Fe, Mn, Ni, Pb and Zn and radionuclides 226 Ra and 228 Ra, alpha and beta total and gamma emitters in the treatment systems, from the analysis of the concentrations of these in the waters and residues, evaluating the suitability of the waters in accordance with established in the norms in force, as well as the associated with the disposal of wastes that are commonly released into the environment. The results obtained for the metals indicated that the treatment systems must have their processes optimized to ensure the adequacy of the water supplied to the population to the potability parameters and for the residues levels that could generate environmental risk were observed. For the radionuclides the levels found in the waters were low, indicating a low contribution of these to the sources undergoing treatment, and in the residues the levels were low, but within the range described in the literature, corroborating its classification as a TENORM

Adherence to Technology-Mediated Insomnia Treatment: A Meta-Analysis, Interviews, and Focus Groups

OpenAIRE

Horsch, Corine; Lancee, Jaap; Beun, Robbert Jan; Neerincx, Mark A; Brinkman, Willem-Paul

2015-01-01

Background: Several technologies have been proposed to support the reduction of insomnia complaints. A user-centered assessment of these technologies could provide insight into underlying factors related to treatment adherence. Objective: Gaining insight into adherence to technology-mediated insomnia treatment as a solid base for improving those adherence rates by applying adherence-enhancing strategies. Methods: Adherence to technology-mediated sleep products was studied in three ways. First...

Environmental assessment of digestate treatment technologies using LCA methodology.

Science.gov (United States)

Vázquez-Rowe, Ian; Golkowska, Katarzyna; Lebuf, Viooltje; Vaneeckhaute, Céline; Michels, Evi; Meers, Erik; Benetto, Enrico; Koster, Daniel

2015-09-01

The production of biogas from energy crops, organic waste and manure has augmented considerably the amounts of digestate available in Flanders. This has pushed authorities to steadily introduce legislative changes to promote its use as a fertilising agent. There is limited arable land in Flanders, which entails that digestate has to compete with animal manure to be spread. This forces many anaerobic digestion plants to further treat digestate in such a way that it can either be exported or the nitrogen be removed. Nevertheless, the environmental impact of these treatment options is still widely unknown, as well as the influence of these impacts on the sustainability of Flemish anaerobic digestion plants in comparison to other regions where spreading of raw digestate is allowed. Despite important economic aspects that must be considered, the use of Life Cycle Assessment (LCA) is suggested in this study to identify the environmental impacts of spreading digestate directly as compared to four different treatment technologies. Results suggest relevant environmental gains when the digestate mix is treated using the examined conversion technologies prior to spreading, although important trade-offs between impact categories were observed and discussed. The promising results of digestate conversion technologies suggest that further LCA analyses should be performed to delve into, for instance, the appropriateness to shift to nutrient recovery technologies rather than digestate conversion treatments. Copyright © 2015 Elsevier Ltd. All rights reserved.

Bundling of harvesting residues and whole-trees and the treatment of bundles; Hakkuutaehteiden ja kokopuiden niputus ja nippujen kaesittely

Energy Technology Data Exchange (ETDEWEB)

Kaipainen, H; Seppaenen, V; Rinne, S

1997-12-31

The conditions on which the bundling of the harvesting residues from spruce regeneration fellings would become profitable were studied. The calculations showed that one of the most important features was sufficient compaction of the bundle, so that the portion of the wood in the unit volume of the bundle has to be more than 40 %. The tests showed that the timber grab loader of farm tractor was insufficient for production of dense bundles. The feeding and compression device of the prototype bundler was constructed in the research and with this device the required density was obtained.The rate of compaction of the dry spruce felling residues was about 40 % and that of the fresh residues was more than 50 %. The comparison between the bundles showed that the calorific value of the fresh bundle per unit volume was nearly 30 % higher than that of the dry bundle. This means that the treatment of the bundles should be done of fresh felling residues. Drying of the bundles succeeded well, and the crushing and chipping tests showed that the processing of the bundles at the plant is possible. The treatability of the bundles was also excellent. By using the prototype, developed in the research, it was possible to produce a bundle of the fresh spruce harvesting residues, the diameter of which was about 50 cm and the length about 3 m, and the rate of compaction over 50 %. By these values the reduction target of the costs is obtainable

Bundling of harvesting residues and whole-trees and the treatment of bundles; Hakkuutaehteiden ja kokopuiden niputus ja nippujen kaesittely

Energy Technology Data Exchange (ETDEWEB)

Kaipainen, H.; Seppaenen, V.; Rinne, S.

1996-12-31

The conditions on which the bundling of the harvesting residues from spruce regeneration fellings would become profitable were studied. The calculations showed that one of the most important features was sufficient compaction of the bundle, so that the portion of the wood in the unit volume of the bundle has to be more than 40 %. The tests showed that the timber grab loader of farm tractor was insufficient for production of dense bundles. The feeding and compression device of the prototype bundler was constructed in the research and with this device the required density was obtained.The rate of compaction of the dry spruce felling residues was about 40 % and that of the fresh residues was more than 50 %. The comparison between the bundles showed that the calorific value of the fresh bundle per unit volume was nearly 30 % higher than that of the dry bundle. This means that the treatment of the bundles should be done of fresh felling residues. Drying of the bundles succeeded well, and the crushing and chipping tests showed that the processing of the bundles at the plant is possible. The treatability of the bundles was also excellent. By using the prototype, developed in the research, it was possible to produce a bundle of the fresh spruce harvesting residues, the diameter of which was about 50 cm and the length about 3 m, and the rate of compaction over 50 %. By these values the reduction target of the costs is obtainable

Reactivity of Athabasca residue and of its SARA fractions during residue hydroconversion

Energy Technology Data Exchange (ETDEWEB)

Verstraete, J.; Danial-Fortain, P.; Gauthier, T.; Merdrignac, I. [IFP-Lyon, Vermaison (France); Budzinski, H. [Bordeaux Univ. (France). ISM-LPTC, UMR CNRS

2009-07-01

Residue conversion processes are becoming increasingly important because of the declining market for residual fuel oil and a greater demand for middle distillates. Ebullated-bed hydroconversion is a commercially proven technology for converting heavy feedstocks with high amounts of impurities. The process enables the conversion of atmospheric or vacuum residues at temperatures up to 440 degrees C, and at liquid hourly space velocity (LHSV) conditions in the range of 0.15 to 0.5 per hour. A 540 degrees C conversion of up to 80 weight per cent can be achieved under these conditions. This paper reported on a research study conducted at IFP Lyon in which the residue hydroconversion in a large-scale ebullated bed bench unit was investigated to determine the impact of operating conditions and feed properties on yield and product qualities. Hydrogen was added to the feed in the bench units to keep a high hydrogen partial pressure and favour the catalytic hydroconversion reactions. In a typical test, the reactor was fed with 50 g of feedstock and 0.45 g of crushed equilibrium industrial NiMo catalyst, pressurized hydrogen and quickly heated at the reaction temperature. This paper also discussed the conversion of Athabasca bitumen residue in the large-scale pilot plant and also in the small scale batch reactor. The effect of operating temperature and space velocity was examined. The reactivity of the saturates, aromatics, resins and asphaltenes (SARA) fractions of the bitumen was studied separately in order to better understand the conversion mechanisms and reactivities. The Athabasca bitumen feed and SARA fractions were also analyzed in terms of standard petroleum analysis, SARA fractionation, elemental analysis, size exclusion chromatography (SEC) and 13C NMR. Hydroconversion experiments were conducted in the batch unit at different reaction temperatures and reaction times. A comparison of small-scale batch results with those obtained with the continuous large-scale bench

Development of treatment technologies for the processing of US Department of Energy mixed waste

International Nuclear Information System (INIS)

Backus, P.M.; Berry, J.B.; Coyle, G.J.; Lurk, P.W.; Wolf, S.M.

1993-01-01

Waste contaminated with chemically hazardous and radioactive species is defined as mixed waste. Significant technology development has been conducted for separate treatment of hazardous and radioactive waste, but technology development addressing mixed-waste treatment has been limited. Management of mixed waste requires treatment which must meet the standards established by the US Environmental Protection Agency for the specific hazardous constituents while also providing adequate control of the radionuclides. Technology has not been developed, demonstrated, or tested to produce a low-risk final waste form specifically for mixed waste. Throughout the US Department of Energy (DOE) complex, mixed waste is a problem because definitive treatment standards have not been established and few disposal facilities are available. Treatment capability and capacity are also limited. Site-specific solutions to the management of mixed waste have been initiated; however, site-specific programs result in duplication of technology development between various sites. Significant progress is being made in developing technology for mixed waste under the Mixed Waste Integrated Program. The status of the technical initiatives in chemical/physical treatment, destruction/stabilization technology, off-gas treatment, and final waste form production/assessment is described in this paper

[Biooxidation of gold-bearing sulfide ore and subsequent biological treatment of cyanidation residues].

Science.gov (United States)

Kanaev, A T; Bulaev, A G; Semenchenko, G V; Kanaeva, Z K; Shilmanova, A A

2016-01-01

The percolation biooxidation parameters of ore from the Bakyrchik deposit were studied. An investigation of the technological parameters (such as the concentration of leaching agents, irrigation intensity, and pauses at various stages of the leaching) revealed the optimal mode for precious metal extraction. The stages of the ore processing were biooxidation, gold extraction by cyanidation or thiosulfate leaching, and biological destruction of cyanide. The gold and silver recovery rates by cyanidation were 64.0 and 57.3%, respectively. The gold and silver recovery rates by thiosulfate leaching were 64.0 and 57.3%, respectively. Gold and silver recovery rates from unoxidized ore (control experiment) by cyanidation were 20.9 and 26.8%, respectively. Thiosulfate leaching of unoxidized ore allowed the extraction of 38.8 and 24.2% of the gold and silver, respectively. Cyanidation residues were treated with bacteria of the genus Alcaligenes in order to destruct cyanide.

Residues and duality for projective algebraic varieties

CERN Document Server

Kunz, Ernst; Dickenstein, Alicia

2008-01-01

This book, which grew out of lectures by E. Kunz for students with a background in algebra and algebraic geometry, develops local and global duality theory in the special case of (possibly singular) algebraic varieties over algebraically closed base fields. It describes duality and residue theorems in terms of K�hler differential forms and their residues. The properties of residues are introduced via local cohomology. Special emphasis is given to the relation between residues to classical results of algebraic geometry and their generalizations. The contribution by A. Dickenstein gives applications of residues and duality to polynomial solutions of constant coefficient partial differential equations and to problems in interpolation and ideal membership. D. A. Cox explains toric residues and relates them to the earlier text. The book is intended as an introduction to more advanced treatments and further applications of the subject, to which numerous bibliographical hints are given.

Corrective Techniques and Future Directions for Treatment of Residual Refractive Error Following Cataract Surgery

Science.gov (United States)

Moshirfar, Majid; McCaughey, Michael V; Santiago-Caban, Luis

2015-01-01

Postoperative residual refractive error following cataract surgery is not an uncommon occurrence for a large proportion of modern-day patients. Residual refractive errors can be broadly classified into 3 main categories: myopic, hyperopic, and astigmatic. The degree to which a residual refractive error adversely affects a patient is dependent on the magnitude of the error, as well as the specific type of intraocular lens the patient possesses. There are a variety of strategies for resolving residual refractive errors that must be individualized for each specific patient scenario. In this review, the authors discuss contemporary methods for rectification of residual refractive error, along with their respective indications/contraindications, and efficacies. PMID:25663845

Endoscopic Endonasal Versus Microscopic Transsphenoidal Surgery for Recurrent and/or Residual Pituitary Adenomas.

Science.gov (United States)

Esquenazi, Yoshua; Essayed, Walid I; Singh, Harminder; Mauer, Elizabeth; Ahmed, Mudassir; Christos, Paul J; Schwartz, Theodore H

2017-05-01

Surgery for recurrent/residual pituitary adenomas is increasingly being performed through endoscopic surgery. Whether this new technology has altered the indications and outcomes of surgery is unknown. We conducted a systematic review and meta-analysis of published studies to compare the indications and outcomes between microscopic and endoscopic approaches. A PubMed search was conducted (1985-2015) to identify surgical series of endoscopic endonasal and microscopic transsphenoidal resection of residual or recurrent pituitary adenomas. Data were extracted regarding tumor characteristics, surgical treatment, extent of resection, endocrine remission, visual outcome, and complications. Twenty-one studies met inclusion criteria. A total of 292 patients were in the endoscopic group, and 648 patients were in the microscopic group. Endoscopic cases were more likely nonfunctional (P < 0.001) macroadenomas (P < 0.001) with higher rates of cavernous sinus invasion (P = 0.012). The pooled rate of gross total tumor resection was 53.5% for the endoscopic group and 46.6% for the microscopic group. Endocrine remission was achieved in 53.0% and 46.7% of patients, and visual improvement occurred in 73.2% and 49.6% for the endoscopic and microscopic groups. Cerebrospinal fluid leak and pituitary insufficiency were higher in the endoscopic group. This meta-analysis indicates that the use of the endoscope to reoperate on residual or recurrent adenomas has only led to modest increases in resection rates. However, larger more complex cases are being tackled, so direct comparisons are misleading. The most dramatic change has been in visual improvement along with modest increases in risk. Reoperation for recurrent or residual adenomas is a safe and effective treatment option. Copyright © 2017 Elsevier Inc. All rights reserved.

X-ray measurement of residual stress on bolt threads

International Nuclear Information System (INIS)

Hagiwara, Masaya; Nakahara, Kanefumi; Yoshimoto, Isamu.

1989-01-01

This study deals with X-ray measurement of residual stress at the local area around the thread root of a bolt. Residual stress in the 0.5 mm x 5 mm area was measured using a method of stepped scanning and parabolic approximation. The conditions of measurement had been determined and evaluated through the preliminary measurement of compressive stress acting on the cylindrical surface. Furthermore, the fatigue strength estimated by applying the residual stress data to the previously presented hypothesis was compared with the experimental results. The main conclusions obtained were as follows: (1) The residual stress in a relatively small area on the cylindrical surface with large curvature can be measured by X-ray using a method of stepped scanning and parabolic approximation; (2) The compressive residual stress measured at the thread root was larger for the bolt manufactured by thread rolling after heat treatment than for one manufactured by thread rolling before heat treatment; (3) The distribution of residual stress along the axial direction from the thread root to the portion under crest did not represent remarkable change in its value; (4) The residual stress of a bolt was somewhat decreased by fatigue loading on the condition of low mean stress; (5) The fatigue strength estimated using residual stress data showed the tendency of experimental results well. (author)

Effect of torrefaction pre-treatment on physical and combustion characteristics of biomass composite briquette from rice husk and banana residue

Directory of Open Access Journals (Sweden)

Amira Atan Nor

2018-01-01

Full Text Available Biomass is an alternative renewable energy sources that can generates energy almost same as fossil fuel. The depletion sources of fossil fuel had increase the potential use of biomass energy. In Malaysia, rice husk and banana residues are abundantly left and not treated with proper disposal method which later may contribute to environment and health problems. Thus the development of biomass composite briquette made from rice husk and banana residue is one of the potential ways to reduce the problems and hence may contribute the better way to treat the waste by recycling the waste into a form of biomass product. The biomass briquettes are used for thermal applications because it can produce a complete combustion as it has a consistent quality and high burning efficiency. However, the quality of the biomass briquette can be added by application of torrefaction pre-treatment method. Torrefaction is a thermal method that can produce more high quality of the briquette with high calorific value, high fixed carbon content, low volatile matter, and low ash content. This study was conducted to assess the physical and combustion characteristic of the biomass briquette from rice husk and banana residue which was produced through torrefaction process. The biomass briquette, were densified by using hot press machine with temperature of 180°C for about 30 minutes. The briquette produce are 150 μm in particle size with varies in mixing ratio of rice husk to banana residue which are 100:0, 80:20 and 60:40. After the briquetting process, the biomass fuel briquettes have been undergoes parameter testing and the data have been analysed. Result showed the best biomass briquette is developed from torrefied rice husk and banana residue mixed at ratio of 60:40. Moreover, SEM image reveal that torrefaction pre-treatment has shrinkage the fibres size which confirming the thermal stability of the briquette.

Energy positive domestic wastewater treatment: the roles of anaerobic and phototrophic technologies.

Science.gov (United States)

Shoener, B D; Bradley, I M; Cusick, R D; Guest, J S

2014-05-01

The negative energy balance of wastewater treatment could be reversed if anaerobic technologies were implemented for organic carbon oxidation and phototrophic technologies were utilized for nutrient recovery. To characterize the potential for energy positive wastewater treatment by anaerobic and phototrophic biotechnologies we performed a comprehensive literature review and analysis, focusing on energy production (as kJ per capita per day and as kJ m(-3) of wastewater treated), energy consumption, and treatment efficacy. Anaerobic technologies included in this review were the anaerobic baffled reactor (ABR), anaerobic membrane bioreactor (AnMBR), anaerobic fluidized bed reactor (AFB), upflow anaerobic sludge blanket (UASB), anaerobic sequencing batch reactor (ASBR), microbial electrolysis cell (MEC), and microbial fuel cell (MFC). Phototrophic technologies included were the high rate algal pond (HRAP), photobioreactor (PBR), stirred tank reactor, waste stabilization pond (WSP), and algal turf scrubber (ATS). Average energy recovery efficiencies for anaerobic technologies ranged from 1.6% (MFC) to 47.5% (ABR). When including typical percent chemical oxygen demand (COD) removals by each technology, this range would equate to roughly 40-1200 kJ per capita per day or 110-3300 kJ m(-3) of treated wastewater. The average bioenergy feedstock production by phototrophic technologies ranged from 1200-4700 kJ per capita per day or 3400-13 000 kJ m(-3) (exceeding anaerobic technologies and, at times, the energetic content of the influent organic carbon), with usable energy production dependent upon downstream conversion to fuels. Energy consumption analysis showed that energy positive anaerobic wastewater treatment by emerging technologies would require significant reductions of parasitic losses from mechanical mixing and gas sparging. Technology targets and critical barriers for energy-producing technologies are identified, and the role of integrated anaerobic and

Energy positive domestic wastewater treatment: the roles of anaerobic and phototrophic technologies

KAUST Repository

Shoener, B. D.

2014-01-01

The negative energy balance of wastewater treatment could be reversed if anaerobic technologies were implemented for organic carbon oxidation and phototrophic technologies were utilized for nutrient recovery. To characterize the potential for energy positive wastewater treatment by anaerobic and phototrophic biotechnologies we performed a comprehensive literature review and analysis, focusing on energy production (as kJ per capita per day and as kJ m-3 of wastewater treated), energy consumption, and treatment efficacy. Anaerobic technologies included in this review were the anaerobic baffled reactor (ABR), anaerobic membrane bioreactor (AnMBR), anaerobic fluidized bed reactor (AFB), upflow anaerobic sludge blanket (UASB), anaerobic sequencing batch reactor (ASBR), microbial electrolysis cell (MEC), and microbial fuel cell (MFC). Phototrophic technologies included were the high rate algal pond (HRAP), photobioreactor (PBR), stirred tank reactor, waste stabilization pond (WSP), and algal turf scrubber (ATS). Average energy recovery efficiencies for anaerobic technologies ranged from 1.6% (MFC) to 47.5% (ABR). When including typical percent chemical oxygen demand (COD) removals by each technology, this range would equate to roughly 40-1200 kJ per capita per day or 110-3300 kJ m-3 of treated wastewater. The average bioenergy feedstock production by phototrophic technologies ranged from 1200-4700 kJ per capita per day or 3400-13000 kJ m-3 (exceeding anaerobic technologies and, at times, the energetic content of the influent organic carbon), with usable energy production dependent upon downstream conversion to fuels. Energy consumption analysis showed that energy positive anaerobic wastewater treatment by emerging technologies would require significant reductions of parasitic losses from mechanical mixing and gas sparging. Technology targets and critical barriers for energy-producing technologies are identified, and the role of integrated anaerobic and phototrophic

Treatment technology analysis for mixed waste containers and debris

International Nuclear Information System (INIS)

Gehrke, R.J.; Brown, C.H.; Langton, C.A.; Askew, N.M.; Kan, T.; Schwinkendorf, W.E.

1994-03-01

A team was assembled to develop technology needs and strategies for treatment of mixed waste debris and empty containers in the Department of Energy (DOE) complex, and to determine the advantages and disadvantages of applying the Debris and Empty Container Rules to these wastes. These rules issued by the Environmental Protection Agency (EPA) apply only to the hazardous component of mixed debris. Hazardous debris that is subjected to regulations under the Atomic Energy Act because of its radioactivity (i.e., mixed debris) is also subject to the debris treatment standards. The issue of treating debris per the Resource Conservation and Recovery Act (RCRA) at the same time or in conjunction with decontamination of the radioactive contamination was also addressed. Resolution of this issue requires policy development by DOE Headquarters of de minimis concentrations for radioactivity and release of material to Subtitle D landfills or into the commercial sector. The task team recommends that, since alternate treatment technologies (for the hazardous component) are Best Demonstrated Available Technology (BDAT): (1) funding should focus on demonstration, testing, and evaluation of BDAT on mixed debris, (2) funding should also consider verification of alternative treatments for the decontamination of radioactive debris, and (3) DOE should establish criteria for the recycle/reuse or disposal of treated and decontaminated mixed debris as municipal waste

Application of radiation technology to sewage sludge processing: A review

International Nuclear Information System (INIS)

Wang Jianlong; Wang Jiazhuo

2007-01-01

Sewage sludge is unwanted residual solid wastes generated in wastewater treatment and its management is one of the most critical environmental issues of today. The treatment and disposal of sludge contribute a considerable proportion of the cost for running a wastewater treatment plant. The increasing amount of swage sludge and more and more legislative regulation of its disposal have stimulated the need for developing new technologies to process sewage sludge efficiently and economically. One ideal consideration is to recycle it after proper treatment. Radiation technology is regarded to be a promising alternative for its high efficiency in pathogen inactivation, organic pollutants oxidation, odor nuisance elimination and some other characteristics enhancement, which will facilitate the down-stream process of sludge treatment and disposal. Here we present a brief review of application of radiation technology on sewage sludge processing. Some basic information of two currently available irradiation systems and fundamental radiation chemistry are introduced firstly; then the world-wide application of this promising technology is reviewed; various effects of radiation on sludge is discussed in detail; and some concluding remarks are given and some future directions are also proposed

Innovative technologies for the treatment of hazardous and mixed wastes

International Nuclear Information System (INIS)

Eyman, L.D.; Anderson, T.D.

1988-01-01

The treatment, storage, and disposal of hazardous and mixed wastes incur significant costs for Department of Energy (DOE) installations. These wastes must be managed under strict environmental controls and regulations to prevent the possibility of migration of hazardous materials to the biosphere. Through the Hazardous Waste Remedial Actions Program, the DOE is seeking to develop innovative ways of improving current treatment technologies to eliminate the hazardous components of wastes, reduce waste management costs, and minimize the volume requiring disposal as hazardous or mixed waste. Sponsored projects progress from research and development to field demonstration. Among the innovative technologies under development are supercritical water oxidation of hazardous chemicals, microwave-assisted destruction of chlorinated hydrocarbons, paramagnetic separation of metals from waste, detoxification and reclamation of waste acid, nitrate destruction through calcination, treatment/disposal of reactive metals, and methodologies for encapsulation. Technologies at a demonstration phase include detoxification of mixed waste sludge, microbial degradation of polychlorinated biphenyls in soil, and the remediation process for a hydrocarbon spill. 14 refs

Sclerosis and the Nd:YAG, Q-switched laser with multiple frequency for treatment of telangiectases, reticular veins, and residual pigmentation.

Science.gov (United States)

Cisneros, J L; Del Rio, R; Palou, J

1998-10-01

The combination of low concentrations of sclerosing solution and the Nd:YAG, Q-switched laser with multiple (quadruple) frequency provides good results in the treatment of telangiectases and reticular varicose veins of the lower extremities, as well as pigmentation that may appear during sclerotherapy. This paper is based on a series of patients with telangiectases and reticular veins who were treated with sclerotherapy and the Nd:YAG, Q-switched laser with quadruple frequency. Patients with telangiectases and reticular veins received two or three treatment sessions with polydocanol and the Nd:YAG, Q-switched laser with quadruple frequency. Then, they were assessed a clinical score corresponding to the level of improvement achieved. Residual hematic pigmentation lesions were also eliminated with the laser. Excellent improvement was evident in 90% of the patients with minimal residual lesions. The combined technique of sclerosing solution and the Nd:YAG laser with multiple frequency is a valid alternative for the elimination of telangiectases and reticular veins of the lower limbs. This technique has several advantages, such as the use of low concentrations of sclerosing solution, high patient acceptance levels due to minimal disturbances, and the fact that local anesthesia is unnecessary. Good results are obtained without complications and minimal residual pigmentation. These mild pigmentation can be treated with the Nd:YAG laser.

Evaluation of heavy metals in hazardous automobile shredder residue thermal residue and immobilization with novel nano-size calcium dispersed reagent

International Nuclear Information System (INIS)

Lee, Chi-Hyeon; Truc, Nguyen Thi Thanh; Lee, Byeong-Kyu; Mitoma, Yoshiharu; Mallampati, Srinivasa Reddy

2015-01-01

Graphical abstract: Schematic representation of possible mechanisms determining the heavy metals immobilization efficiencyof ASR dust/thermal residues after treatment with nanometallic Ca/CaO/PO 4 . - Highlights: • Nanometallic Ca/CaO/PO 4 for heavy metals immobilization in ASR residue. • Heavy metals immobilization in dry condition attained about 95–100%. • Remaining heavy metals were lower than the Korean standard regulatory limit. • The amounts of heavy metals detectable on the ASR dust surface decreased. • Nanometallic Ca/CaO/PO 4 has a promising potential for heavy metal remediation. - Abstract: This study was conducted to synthesize and apply a nano-size calcium dispersed reagent as an immobilization material for heavy metal-contaminated automobile shredder residues (ASR) dust/thermal residues in dry condition. Simple mixing with a nanometallic Ca/CaO/PO 4 dispersion mixture immobilized 95–100% of heavy metals in ASR dust/thermal residues (including bottom ash, cavity ash, boiler and bag filter ash). The quantity of heavy metals leached from thermal residues after treatment by nanometallic Ca/CaO/PO 4 was lower than the Korean standard regulatory limit for hazardous waste landfills. The morphology and elemental composition of the nanometallic Ca/CaO-treated ASR residue were characterized by field emission scanning election microscopy combined with electron dispersive spectroscopy (FE-SEM/EDS). The results indicated that the amounts of heavy metals detectable on the ASR thermal residue surface decreased and the Ca/PO 4 mass percent increased. X-ray diffraction (XRD) pattern analysis indicated that the main fraction of enclosed/bound materials on ASR residue included Ca/PO 4 − associated crystalline complexes, and that immobile Ca/PO 4 salts remarkably inhibited the desorption of heavy metals from ASR residues. These results support the potential use of nanometallic Ca/CaO/PO 4 as a simple, suitable and highly efficient material for the gentle

Evaluation of heavy metals in hazardous automobile shredder residue thermal residue and immobilization with novel nano-size calcium dispersed reagent

Energy Technology Data Exchange (ETDEWEB)

Lee, Chi-Hyeon; Truc, Nguyen Thi Thanh [Department of Civil and Environmental Engineering, University of Ulsan, Daehak-ro 93, Nam-gu, Ulsan 680-749 (Korea, Republic of); Lee, Byeong-Kyu, E-mail: bklee@ulsan.ac.kr [Department of Civil and Environmental Engineering, University of Ulsan, Daehak-ro 93, Nam-gu, Ulsan 680-749 (Korea, Republic of); Mitoma, Yoshiharu [Department of Environmental Sciences, Prefectural University of Hiroshima, 562 Nanatsuka-Cho Shobara City, Hiroshima 727-0023 (Japan); Mallampati, Srinivasa Reddy, E-mail: srireddys@ulsan.ac.kr [Department of Civil and Environmental Engineering, University of Ulsan, Daehak-ro 93, Nam-gu, Ulsan 680-749 (Korea, Republic of)

2015-10-15

Graphical abstract: Schematic representation of possible mechanisms determining the heavy metals immobilization efficiencyof ASR dust/thermal residues after treatment with nanometallic Ca/CaO/PO{sub 4}. - Highlights: • Nanometallic Ca/CaO/PO{sub 4} for heavy metals immobilization in ASR residue. • Heavy metals immobilization in dry condition attained about 95–100%. • Remaining heavy metals were lower than the Korean standard regulatory limit. • The amounts of heavy metals detectable on the ASR dust surface decreased. • Nanometallic Ca/CaO/PO{sub 4} has a promising potential for heavy metal remediation. - Abstract: This study was conducted to synthesize and apply a nano-size calcium dispersed reagent as an immobilization material for heavy metal-contaminated automobile shredder residues (ASR) dust/thermal residues in dry condition. Simple mixing with a nanometallic Ca/CaO/PO{sub 4} dispersion mixture immobilized 95–100% of heavy metals in ASR dust/thermal residues (including bottom ash, cavity ash, boiler and bag filter ash). The quantity of heavy metals leached from thermal residues after treatment by nanometallic Ca/CaO/PO{sub 4} was lower than the Korean standard regulatory limit for hazardous waste landfills. The morphology and elemental composition of the nanometallic Ca/CaO-treated ASR residue were characterized by field emission scanning election microscopy combined with electron dispersive spectroscopy (FE-SEM/EDS). The results indicated that the amounts of heavy metals detectable on the ASR thermal residue surface decreased and the Ca/PO{sub 4} mass percent increased. X-ray diffraction (XRD) pattern analysis indicated that the main fraction of enclosed/bound materials on ASR residue included Ca/PO{sub 4}− associated crystalline complexes, and that immobile Ca/PO{sub 4} salts remarkably inhibited the desorption of heavy metals from ASR residues. These results support the potential use of nanometallic Ca/CaO/PO{sub 4} as a simple, suitable and

Validation of an UHPLC-MS/MS Method for Screening of Antimicrobial Residues in Eggs and Their Application to Analyses of Eggs from Laying Hens Subjected to Pharmacological Treatment

Directory of Open Access Journals (Sweden)

Letícia Gomes Magnago Caldeira

2017-01-01

Full Text Available A multiresidue method by UHPLC/MS-MS was optimized and validated for the screening and semiquantitative detection of antimicrobials residues from tetracyclines, aminoglycosides, quinolones, lincosamides, β-lactams, sulfonamides, and macrolides families in eggs. A qualitative approach was used to ensure adequate sensitivity to detect residues at the level of interest, defined as maximum residue limit (MRL, or less. The applicability of the methods was assessed by analyzing egg samples from hens that had been subjected to pharmacological treatment with neomycin, enrofloxacin, lincomycin, oxytetracycline, and doxycycline during five days and after discontinuation of medication (10 days. The method was adequate for screening all studied analytes in eggs, since the performance parameters ensured a false-compliant rate below or equal to 5%, except for flumequine. In the analyses of eggs from laying hens subjected to pharmacological treatment, all antimicrobial residues were detected throughout the experimental period, even after discontinuation of medication, except for neomycin, demonstrating the applicability of the method for analyses of antimicrobial residues in eggs.

Novel Technology for Phenol Wastewater Treatment Using Electrochemical Reactor

Directory of Open Access Journals (Sweden)

Yuncheng Xie

2015-01-01

Full Text Available There are various electrochemical approaches to save energy, mostly by means of equipment improvement coupled with other water treatment technologies. Replacement of DC power with pulse power, modified reactor coupled with photocatalysis can decrease cost. But more or less additional input is developed, or infrastructure has to be replaced. In this paper, an N-Step electrochemical reactor, based on stage reaction modeling, is put forward. On the basis of not changing equipment investment and by adjustment of the operating current density at different levels, power consumption decreases. This model develops a foundation of electrochemical water treatment technology for the engineering application.

[Application of three-dimensional digital technology in the diagnosis and treatment planning in orthodontics].

Science.gov (United States)

Bai, Y X

2016-06-01

Three-dimensional(3D)digital technology has been widely used in the field of orthodontics in clinical examination, diagnosis, treatment and curative effect evaluation. 3D digital technology greatly improves the accuracy of diagnosis and treatment, and provides effective means for personalized orthodontic treatment. This review focuses on the application of 3D digital technology in the field of orthodontics.

ENDOSCOPIC TECHNOLOGIES IN EARLY RECTAL CANCER TREATMENT

Directory of Open Access Journals (Sweden)

D. V. Samsonov

2015-01-01

Full Text Available Total mesorectal excision is the “golden standard” of surgical treatment for rectal cancer. Development of endoscopic technologies allowed to implement the benefits of minimally invasive surgery in early rectal cancer treatment, decrease morbidity and mortality, improve functional outcome and quality of life. Oncological safety of this method is still a subject for discussion due to lack of lymph node harvest. Endoscopic operations for early rectal cancer are being actively implemented in daily practice, but lack of experience does not allow to include this method in national clinical prac-tice guidelines.

Demonstration of the SOLTECR technology for the in situ physico-chemical treatment of a site contaminated by diesel oil

International Nuclear Information System (INIS)

Dufresne, P.; Tellier, J.G.; Michaud, J.R.

1997-01-01

The remediation of a diesel oil spill at one of the Alcan plants was discussed. The hydrocarbon spill affected the groundwater in an area of more than 6,000 m 2 . Only an in-situ treatment for remediation was practical because the residual contaminated soil was located mainly under buildings and represented a volume of 3,000 m 3 . Alcan proposed the development and demonstration of the SOLTEC R in-situ physico-chemical treatment technology which consists of injecting chemicals into the soil. The chemicals are a mixture of calcium based solids with liquid and gaseous oxidizing agents. The degradation of the hydrocarbons is by oxidation and is completed in the soil in less than 24 hours after injection. Monitoring of the groundwater was conducted for one year after the completion of the soil treatment. It was concluded that the SOLTEC R process decreased and even eliminated the toxicity and geotoxicity of the diesel-contaminated soils. A volume of 3,000 m 3 of contaminated soil was treated within three months. The efficiency of hydrocarbon destruction was more than 95 per cent. 3 refs., 1 tab

The development of radioactive waste treatment technology(IV)

International Nuclear Information System (INIS)

Kim, Joon Hyung; Yim, Sung Paal; Lee, Kune Woo; Yoo, Jeong Woo; Kim, Young Min; Park, Seong Chul

1992-03-01

Following studies were performed in the project of development of radioactive waste treatment technology. 1) Treatment of radioactive borated liquid wastes by reverse osmosis : Separation characteristics of boric acid were estimated using cellulose acetate membrane and aromatic polyamide membrane. The performance of reverse osmosis process was evaluated in terms of boric acid recovery, radiochemical rejection, and membrane flux by operating variables such as applied pressure and feed concentration. 2) Oily waste treatment : The mathematical model to estimate oil removal efficiency is to be proposed at coalescence column. 3) Treatment of radioactive laundry waste 4) Comparison of evaporation and ion-exchange 5) State of the art of high integrity container. (Author)

Residual nilpotence and residual solubility of groups

International Nuclear Information System (INIS)

Mikhailov, R V

2005-01-01

The properties of the residual nilpotence and the residual solubility of groups are studied. The main objects under investigation are the class of residually nilpotent groups such that each central extension of these groups is also residually nilpotent and the class of residually soluble groups such that each Abelian extension of these groups is residually soluble. Various examples of groups not belonging to these classes are constructed by homological methods and methods of the theory of modules over group rings. Several applications of the theory under consideration are presented and problems concerning the residual nilpotence of one-relator groups are considered.

Insights into the mechanisms of mercury sorption onto aluminum based drinking water treatment residuals.

Science.gov (United States)

Deliz Quiñones, Katherine; Hovsepyan, Anna; Oppong-Anane, Akua; Bonzongo, Jean-Claude J

2016-04-15

Several studies have demonstrated the ability of drinking water treatment residuals (WTRs) to efficiently sorb metal cations from aqueous solutions. Reported results have stimulated interest on the potential use of WTRs as sorbent for metal removal from contaminated aqueous effluents as well as in metal immobilization in contaminated soils. However, knowledge on mechanisms of metal sorption by WTRs remains very limited and data on the long-term stability of formed metal-WTR complexes as a function of changing key environmental parameters are lacking. In this study, chemical selective sequential extraction (SSE), scanning electron microscopy combined with X-ray energy dispersive spectrometer (SEM-EDS), and X-ray photoelectron spectroscopy (XPS) were used to gain insight into the different mechanisms of mercury (Hg) binding to aluminum based WTR (Al-WTRs). Results from sorption studies show that a significant portion of Hg becomes incorporated in the operationally defined residual fraction of Al-WTRs, and therefore, not prone to dissolution and mobility. The results of solid phase analyses suggested that Hg immobilization by Al-WTR occurs largely through its binding to oxygen donor atoms of mineral ligands driven by a combination of electrostatic forces and covalent bonding. Copyright © 2016 Elsevier B.V. All rights reserved.

Thermal inertializing of solid incinerator residues

International Nuclear Information System (INIS)

Proelss, J.

2003-01-01

Inertialization of residues is a key task of incinerators. Residues of conventional incineration processes may contain high levels of inorganic or organic pollutants and must be treated prior to recycling. the most effective process is thermal treatment above the melting point. This will destroy organic pollutants like dioxins/furans and pathogenic compounds, while the heavy metals will be partly volatilized. The glassy slag obtained as end product is low in heavy metals and more or less resistant to leaching. The The author describes a method for calculating activity coefficients of volatile components of diluted, liquid multicomponent systems. With these data, the data base for thermodynamic description of fluid mixtures was updated, and a set of characteristic data was established for describing transport in an inflatable module. Once the activity coefficients of interesting constituents of the slag are known along with the transport conditions in the volatilization process, it is possible to optimize the thermal treatment of critical ashes and dusts with a view to energy consumption and process control. In two different exemplary process concepts, the energy consumption for residue treatment is estimated. The processes proposed are compared with published process proposals, and their energy consumption is assessed in a comoparative study [de

Residual coal exploitation and its impact on sustainable development of the coal industry in China

International Nuclear Information System (INIS)

Zhang, Yujiang; Feng, Guorui; Zhang, Min; Ren, Hongrui; Bai, Jinwen; Guo, Yuxia; Jiang, Haina; Kang, Lixun

2016-01-01

Although China owns large coal reserves, it now faces the problem of depletion of its coal resources in advance. The coal-based energy mix in China will not change in the short term, and a means of delaying the coal resources depletion is therefore urgently required. The residual coal was exploited first with a lower recovery percentage and was evaluated as commercially valuable damaged coal. This approach is in comparison to past evaluations when the residual coal was allocated as exploitation losses. Coal recovery rates, the calculation method of residual coal reserves and statistics of its mines in China were given. On this basis, a discussion concerning the impacts on the delay of China's coal depletion, development of coal exploitation and sustainable developments, as well as technologies and relevant policies, were presented. It is considered that the exploitation of residual coal can effectively delay China's coal depletion, inhibit the construction of new mines, redress the imbalance between supply and demand of coal in eastern China, improve the mining area environment and guarantee social stability. The Chinese government supports the exploitation technologies of residual coal. Hence, exploiting residual coal is of considerable importance in sustainable development of the coal industry in China. - Highlights: •Pay attention to residual coal under changing energy-mix environment in China. •Estimate residual coal reserves and investigate its exploitation mines. •Discuss impacts of residual coal exploitation on delay of coal depletion in China. •Discuss impacts on coal mining industry and residual coal exploitation technology. •Give corresponding policy prescriptions.

CyberKnife SRS: new technologies that enhance the treatment of cancer

International Nuclear Information System (INIS)

Cohen, A.

2008-01-01

The CyberKnife Robotic Radiosurgery System (Accuracy Incorporated, Sunnyvale, CA, USA) is used worldwide to treat tumors and neurological disorders anywhere in the body with sub-millimetre beam delivery accuracy. Accuracy has developed a number of new technologies in recent years to enhance the treatment of cancer patients. Such new technologies include a fast Monte Carlo Dose Calculation algorithm, Sequential Optimization dose planning, the Iris TM Variable Aperture Collimator, an 800 MU/min Linear Accelerator, and Optimized Path Traversal. These technologies enable physicists and physicians to plan treatments quickly and easily and deliver them with unrivalled accuracy and precision

Boron and Coumaphos Residues in Hive Materials Following Treatments for the Control of Aethina tumida Murray.

Directory of Open Access Journals (Sweden)

Cesar Valdovinos-Flores

Full Text Available In the search of alternatives for controlling Aethina tumida Murray, we recently proposed the BAA trap which uses boric acid and an attractant which mimics the process of fermentation caused by Kodamaea ohmeri in the hive. This yeast is excreted in the feces of A. tumida causing the fermentation of pollen and honey of infested hives and releasing compounds that function as aggregation pheromones to A. tumida. Since the boron is the toxic element in boric acid, the aim of this article is to assess the amount of boron residues in honey and beeswax from hives treated with the BAA trap. For this aim, the amount of bioaccumulated boron in products of untreated hives was first determined and then compared with the amount of boron of products from hives treated with the BAA trap in two distinct climatic and soil conditions. The study was conducted in the cities of Padilla, Tamaulipas, and Valladolid, Yucatan (Mexico from August 2014 to March 2015. The quantity of boron in honey was significantly less in Yucatan than in Tamaulipas; this agrees with the boron deficiency among Luvisol and Leptosol soils found in Yucatan compared to the Vertisol soil found in Tamaulipas. In fact, the honey from Yucatan has lower boron levels than those reported in the literature. The BAA treatment was applied for four months, results show that the BAA trap does not have any residual effect in either honey or wax; i.e., there is no significant difference in boron content before and after treatment. On the other hand, the organophosphate pesticide coumaphos was found in 100% of wax samples and in 64% of honey samples collected from Yucatan. The concentration of coumaphos in honey ranges from 0.005 to 0.040 mg/kg, which are below Maximum Residue Limit (MRL allowed in the European Union (0.1 mg/kg but 7.14% of samples exceeded the MRL allowed in Canada (0.02 mg/kg.

Boron and Coumaphos Residues in Hive Materials Following Treatments for the Control of Aethina tumida Murray

Science.gov (United States)

Valdovinos-Flores, Cesar; Gaspar-Ramírez, Octavio; Heras–Ramírez, María Elena; Dorantes-Ugalde, José Antonio; Saldaña-Loza, Luz María

2016-01-01

In the search of alternatives for controlling Aethina tumida Murray, we recently proposed the BAA trap which uses boric acid and an attractant which mimics the process of fermentation caused by Kodamaea ohmeri in the hive. This yeast is excreted in the feces of A. tumida causing the fermentation of pollen and honey of infested hives and releasing compounds that function as aggregation pheromones to A. tumida. Since the boron is the toxic element in boric acid, the aim of this article is to assess the amount of boron residues in honey and beeswax from hives treated with the BAA trap. For this aim, the amount of bioaccumulated boron in products of untreated hives was first determined and then compared with the amount of boron of products from hives treated with the BAA trap in two distinct climatic and soil conditions. The study was conducted in the cities of Padilla, Tamaulipas, and Valladolid, Yucatan (Mexico) from August 2014 to March 2015. The quantity of boron in honey was significantly less in Yucatan than in Tamaulipas; this agrees with the boron deficiency among Luvisol and Leptosol soils found in Yucatan compared to the Vertisol soil found in Tamaulipas. In fact, the honey from Yucatan has lower boron levels than those reported in the literature. The BAA treatment was applied for four months, results show that the BAA trap does not have any residual effect in either honey or wax; i.e., there is no significant difference in boron content before and after treatment. On the other hand, the organophosphate pesticide coumaphos was found in 100% of wax samples and in 64% of honey samples collected from Yucatan. The concentration of coumaphos in honey ranges from 0.005 to 0.040 mg/kg, which are below Maximum Residue Limit (MRL) allowed in the European Union (0.1 mg/kg) but 7.14% of samples exceeded the MRL allowed in Canada (0.02 mg/kg). PMID:27092938

Decentralized peri-urban wastewater treatment technologies assessment integrating sustainability indicators.

Science.gov (United States)

Mena-Ulecia, Karel; Hernández, Heykel Hernández

2015-01-01

Selection of treatment technologies without considering the environmental, economic and social factors associated with each geographical context risks the occurrence of negative impacts that were not properly foreseen, working against the sustainable performance of the technology. The principal aim of this study was to evaluate 12 technologies for decentralized treatment of domestic wastewater applicable to peri-urban communities using sustainability approaches and, at the same time, continuing a discussion about how to address a more integrated assessment of overall sustainability. For this, a set of 13 indicators that embody the environmental, economic and social approach for the overall sustainability assessment were used by means of a target plot diagram as a tool for integrating indicators that represent a holistic analysis of the technologies. The obtained results put forward different degrees of sustainability, which led to the selection of: septic tank+land infiltration; up-flow anaerobic reactor+high rate trickling filter and septic tank+anaerobic filter as the most sustainable and attractive technologies to be applied in peri-urban communities, according to the employed indicators.

MBR technology: a promising approach for the (pre-)treatment of hospital wastewater.

Science.gov (United States)

Beier, S; Cramer, C; Mauer, C; Köster, S; Schröder, H Fr; Pinnekamp, J

2012-01-01

Membrane bioreactor (MBR) technology is a very reliable and extensively tested solution for biological wastewater treatment. Nowadays, separate treatment of highly polluted wastewater streams especially from hospitals and other health care facilities is currently under investigation worldwide. In this context, the MBR technology will play a decisive role because an effluent widely cleaned up from solids and nutrients is absolutely mandatory for a subsequent further elimination of organic trace pollutants. Taking hospital wastewater as an example, the aim of this study was to investigate to what extent MBR technology is an adequate 'pre-treatment' solution for further elimination of trace pollutants. Therefore, we investigated - within a 2-year period - the performance of a full-scale hospital wastewater treatment plant (WWTP) equipped with a MBR by referring to conventional chemical and microbiological standard parameters. Furthermore, we measured the energy consumption and tested different operating conditions. According to our findings the MBR treatment of the hospital wastewater was highly efficient in terms of the removal of solids and nutrients. Finally, we did not observe any major adverse effects on the operation and performance of the MBR system which potentially could derive from the composition of the hospital wastewater. In total, the present study proved that MBR technology is a very efficient and reliable treatment approach for the treatment of highly polluted wastewater from hospitals and can be recommended as a suitable pre-treatment solution for further trace pollutant removal.

Forest residues management guidelines for the Pacific Northwest.

Science.gov (United States)

John M. Pierovich; Edward H. Clarke; Stewart G. Pickford; Franklin R. Ward

1975-01-01

Forest residues often require treatment to meet land management objectives. Guideline statements for managing forest residues are presented to provide direction for achieving these objectives. The latest research information and the best knowledge of experts in various land management disciplines were used to formulate these statements. A unique keying system is...

Study on Integration Treatment Technology of Waste Emulsion from Machining Processing

OpenAIRE

Xin-dong Li; Wan-fu Huang

2013-01-01

The study studied the treatment technology of high concentration emulsion wastewater in metal machining plant. By analyzing the properties of emulsion wastewater, the author used the combination process of membrane technology + Fe-C micro-electrolysis + membrane bioreactor to treat the wastewater. Through the ceramic membrane, the removal rate of CODCr can reach 95%. Fe-C micro-electrolysis treatment can improve the biodegradability of wastewater, lastly through the membrane bioreactor treatm...

Future-proof radioactive waste treatment technologies for nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

Buettner, Klaus; Braehler, Georg [NUKEM Technologies Engineering Services GmbH, Alzenau (Germany)

2014-08-15

In order to select the optimal treatment method for radioactive waste three options can be considered. First, to treat the radioactive waste only to allow long term interim storage until the waste acceptance criteria are defined and the disposal sites are operable. Second, to select treatment methods just in compliance with the current state of discussion with the regard to the above. Third, taking also the future development in the field of waste acceptance criteria and disposal into account. When developing waste treatment systems for Nuclear Power Plants NUKEM Technologies follows the following targets, minimisation of the amount of radioactive waste, maximisation of free release material, volume reduction, avoidance of unwanted materials in the waste package, as well as efficient waste treatment solutions (low investment, high volume reduction). With its technologies produced waste packages fulfil the most stringent waste acceptance criteria.

Treatment of air pollution control residues with iron rich waste sulfuric acid: does it work for antimony (Sb)?

Science.gov (United States)

Okkenhaug, Gudny; Breedveld, Gijs D; Kirkeng, Terje; Lægreid, Marit; Mæhlum, Trond; Mulder, Jan

2013-03-15

Antimony (Sb) in air pollution control (APC) residues from municipal solid waste incineration has gained increased focus due to strict Sb leaching limits set by the EU landfill directive. Here we study the chemical speciation and solubility of Sb at the APC treatment facility NOAH Langøya (Norway), where iron (Fe)-rich sulfuric acid (∼3.6M, 2.3% Fe(II)), a waste product from the industrial extraction of ilmenite, is used for neutralization. Antimony in water extracts of untreated APC residues occurred exclusively as pentavalent antimonate, even at low pH and Eh values. The Sb solubility increased substantially at pH<10, possibly due to the dissolution of ettringite (at alkaline pH) or calcium (Ca)-antimonate. Treated APC residues, stored anoxically in the laboratory, simulating the conditions at the NOAH Langøya landfill, gave rise to decreasing concentrations of Sb in porewater, occurring exclusively as Sb(V). Concentrations of Sb decreased from 87-918μgL(-1) (day 3) to 18-69μgL(-1) (day 600). We hypothesize that an initial sorption of Sb to Fe(II)-Fe(III) hydroxides (green rust) and eventually precipitation of Ca- and Fe-antimonates (tripuhyite; FeSbO4) occurred. We conclude that Fe-rich, sulfuric acid waste is efficient to immobilize Sb in APC residues from waste incineration. Copyright © 2013 Elsevier B.V. All rights reserved.

Research on Treatment Technology and Device of Oily Sludge

Science.gov (United States)

Wang, J. Q.; Shui, F. S.; Li, Q. F.

2017-12-01

Oily sludge is a solid oily waste, which is produced during the process of oil exploitation, transportation, refining and treatment of oily sewage. It contains a great number of hazardous substance, and is difficult to handle with. To solve the problem of waste resources of oil sludge with high oil content and usually not easy to aggregate during the preparation of profile control agent, a new oily sludge treatment device was developed. This device consists of heat supply unit, flush and filter unit, oil removal unit and dehydration unit. It can effectively clean and filter out the waste from oily sludge, recycle the oil resources and reduce the water content of the residue. In the process of operation, the water and chemical agent are recycled in the device, eventually producing little sewage. The device is small, easy to move and has high degree of automation control. The experimental application shows that the oil removal rate of the oily sludge is up to 70%, and the higher the oil content rate the better the treatment.

Properties of sintered glass-ceramics prepared from plasma vitrified air pollution control residues

International Nuclear Information System (INIS)

Roether, J.A.; Daniel, D.J.; Amutha Rani, D.; Deegan, D.E.; Cheeseman, C.R.; Boccaccini, A.R.

2010-01-01

Air pollution control (APC) residues, obtained from a major UK energy from waste (EfW) plant, processing municipal solid waste, have been blended with silica and alumina and melted using DC plasma arc technology. The glass produced was crushed, milled, uni-axially pressed and sintered at temperatures between 750 and 1150 deg. C, and the glass-ceramics formed were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Mechanical properties assessed included Vickers's hardness, flexural strength, Young's modulus and thermal shock resistance. The optimum sintering temperature was found to be 950 deg. C. This produced a glass-ceramic with high density (∼2.58 g/cm 3 ), minimum water absorption (∼2%) and relatively high mechanical strength (∼81 ± 4 MPa). Thermal shock testing showed that 950 deg. C sintered samples could withstand a 700 deg. C quench in water without micro-cracking. The research demonstrates that glass-ceramics can be readily formed from DC plasma treated APC residues and that these have comparable properties to marble and porcelain. This novel approach represents a technically and commercially viable treatment option for APC residues that allow the beneficial reuse of this problematic waste.

Assisted reproductive technology treatment in women with severe eating disorders

DEFF Research Database (Denmark)

Assens, Maria; Ebdrup, Ninna H; Pinborg, Anja

2015-01-01

INTRODUCTION: This national retrospective cohort study investigates the prevalence of women with severe eating disorders in assisted reproductive technology (ART) treatment compared with an age-matched background population without ART treatment. It assesses the frequency distribution of the firs...

Highly Polluted Wastewaters Treatment by Improved Dissolved Air Flotation Technology

Science.gov (United States)

Moga, I. C.; Covaliu, C. I.; Matache, M. G.; Doroftei, B. I.

2017-06-01

Numerous investigations are oriented towards the development of new wastewater treatment technologies, having high efficiencies for removing even low concentrations of pollutants found in water. These efforts were determined by the destroyer impact of the pollutants to the environment and human’s health. For this reason this paper presents our study concerning an improved dissolved air flotation technology for wastewater treatment. There is described a dissolved air flotation (DAF) installation composed by two equipments: pressurized capsule and lamellar settling. Also, there are presented some advantages of using nanoparticles as flotation collectors.

Effect of heteroscedasticity treatment in residual error models on model calibration and prediction uncertainty estimation

Science.gov (United States)

Sun, Ruochen; Yuan, Huiling; Liu, Xiaoli

2017-11-01

The heteroscedasticity treatment in residual error models directly impacts the model calibration and prediction uncertainty estimation. This study compares three methods to deal with the heteroscedasticity, including the explicit linear modeling (LM) method and nonlinear modeling (NL) method using hyperbolic tangent function, as well as the implicit Box-Cox transformation (BC). Then a combined approach (CA) combining the advantages of both LM and BC methods has been proposed. In conjunction with the first order autoregressive model and the skew exponential power (SEP) distribution, four residual error models are generated, namely LM-SEP, NL-SEP, BC-SEP and CA-SEP, and their corresponding likelihood functions are applied to the Variable Infiltration Capacity (VIC) hydrologic model over the Huaihe River basin, China. Results show that the LM-SEP yields the poorest streamflow predictions with the widest uncertainty band and unrealistic negative flows. The NL and BC methods can better deal with the heteroscedasticity and hence their corresponding predictive performances are improved, yet the negative flows cannot be avoided. The CA-SEP produces the most accurate predictions with the highest reliability and effectively avoids the negative flows, because the CA approach is capable of addressing the complicated heteroscedasticity over the study basin.

Identification of diacetonamine from soybean curd residue as a sporulation-inducing factor toward Bacillus spp.

Science.gov (United States)

Ikeda, Aki; Kim, Dongyeop; Hashidoko, Yasuyuki

2017-12-01

Under bioassay-guided investigation, a sporulation-inducing factor (SIF) toward Bacillus spp. was searched for in methanol (MeOH) extracts of soybean curd residues, and diacetonamine (1) was identified as the active compound. SIF was first isolated as a monoacetylated derivative (2, 4.1 mg from 655 g soybean curd residues), and its chemical structure was elucidated by field desorption mass spectrometry, electron ionization mass spectrometry, and nuclear magnetic resonance (NMR) analyses. After 48-h incubation, 40 µM diacetonamine hydrochloride (1b) exhibited sporulation-inducing activity with 35% sporulation frequency toward a Bacillus amyloliquefaciens wild-type strain (AHU 2170), whereas 40 µM diacetone acrylamide (3) showed 99% sporulation induction, which was much higher than that of 1b. Although Bacillus megaterium NBRC 15308 was sporulated by the treatment with 400 µM 1b with 36 and 70% sporulation frequency after 72- and 96-h incubation respectively, 3 at the same concentration showed only 2% sporulation after 72-h incubation. Hence, diacetonamine (1) was characterized as a genuine SIF from soybean curd residues, but it was uncertain whether 1 is a natural product or an artifact. Spores of B. amyloliquefaciens induced by 1b survived after treatment with heating at 95 °C for 10 min, also suggesting that 1 is genuine SIF in soybean curd residue. As sporulation induction is likely linked to activation of antibiotic production in some spore-forming Firmicutes bacteria, compound 1 would be a possible chemical tool to develop an effective fermentation technology in Bacillus species.

Technological advances in the treatment of trauma: a review of promising practices.

Science.gov (United States)

Paul, Lisa A; Hassija, Christina M; Clapp, Joshua D

2012-11-01

Given the availability of empirically supported practices for addressing posttraumatic stress disorder and other forms of trauma-related distress, the development and implementation of new technology to deliver these treatments is exciting. Technological innovations in this literature aim to expand availability of empirically based intervention, increase treatment adherence and acceptability, and overcome barriers commonly encountered with conventional trauma-focused treatment. Much of the current research on these technological developments consists of brief reviews and case studies of the separate therapy modalities. Although this work serves to document the appeal and utility of these innovations, it does not provide comprehensive information about the host of options available. To that end, the three general categories of technological advances in trauma therapy (i.e., videoconferencing, e-Health, virtual reality) are reviewed here, including information regarding their empirical support and suggestions for future research and clinical practice.

Residual stresses in weld-clad reactor pressure vessel steel

International Nuclear Information System (INIS)

Bertram, W.

1975-01-01

Cladding of low alloy nuclear reactor pressure vessel steel with austenitic stainless steel introduces in heavy section components high residual stresses which may cause microcrack formation in stress relief heat treatment. In this investigation an attempt is made to contribute to the solution of the stress relief cracking problem by determining quantitatively the magnitude and distribution of the residual stresses after cladding and after subsequent stress relief heat treatment. The distribution of residual stresses was determined on the basis of a combined experimental-mathematical procedure. Heavy section plate specimens of low alloy steel as base material were given an austenitic monolayer-cladding using the techniques of strip electrode and plasma hot wire cladding, respectively. A number of plates was stress relief heat treated. Starting from the cladded surface the thickness of the plates was reduced by subsequent removal of layers of material. The elastic strain reaction to the removal of each layer was measured by strain gauges. From the data obtained the biaxial residual stress distribution was computed as a function of thickness using relations which are derived for this particular case. In summary, lower residual stresses are caused by reduced thickness of the components. As the heat input, is decreased at identical base material thickness, the residual stresses are lowered also. The height of the tensile residual stress peak, however, remains approximataly constant. In stress relief annealed condition the residual stresses in the cladding are in tension; in the base material the residual stresses are negligibly small

Detailed monitoring of two biogas plants and mechanical solid-liquid separation of fermentation residues.

Science.gov (United States)

Bauer, Alexander; Mayr, Herwig; Hopfner-Sixt, Katharina; Amon, Thomas

2009-06-01

The Austrian "green electricity act" (Okostromgesetz) has led to an increase in biogas power plant size and consequently to an increased use of biomass. A biogas power plant with a generating capacity of 500 kW(el) consumes up to 38,000 kg of biomass per day. 260 ha of cropland is required to produce this mass. The high water content of biomass necessitates a high transport volume for energy crops and fermentation residues. The transport and application of fermentation residues to farmland is the last step in this logistic chain. The use of fermentation residues as fertilizer closes the nutrient cycle and is a central element in the efficient use of biomass for power production. Treatment of fermentation residues by separation into liquid and solid phases may be a solution to the transport problem. This paper presents detailed results from the monitoring of two biogas plants and from the analysis of the separation of fermentation residues. Furthermore, two different separator technologies for the separation of fermentation residues of biogas plants were analyzed. The examined biogas plants correspond to the current technological state of the art and have designs developed specifically for the utilization of energy crops. The hydraulic retention time ranged between 45.0 and 83.7 days. The specific methane yields were 0.40-0.43 m(3)N CH(4) per kg VS. The volume loads ranged between 3.69 and 4.00 kg VS/m(3). The degree of degradation was between 77.3% and 82.14%. The screw extractor separator was better suited for biogas slurry separation than the rotary screen separator. The screw extractor separator exhibited a high throughput and good separation efficiency. The efficiency of slurry separation depended on the dry matter content of the fermentation residue. The higher the dry matter content, the higher the proportion of solid phase after separation. In this project, we found that the fermentation residues could be divided into 79.2% fluid phase with a dry matter

26 CFR 1.860E-1 - Treatment of taxable income of a residual interest holder in excess of daily accruals.

Science.gov (United States)

2010-04-01

... 26 Internal Revenue 9 2010-04-01 2010-04-01 false Treatment of taxable income of a residual interest holder in excess of daily accruals. 1.860E-1 Section 1.860E-1 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES Real Estate Investment...

Advances in the psychosocial treatment of addiction: the role of technology in the delivery of evidence-based psychosocial treatment.

Science.gov (United States)

Marsch, Lisa A; Dallery, Jesse

2012-06-01

The clinical community has a growing array of psychosocial interventions with a strong evidence base available for the treatment of SUDs. Considerable opportunity exists for leveraging technology in the delivery of evidence-based interventions to promote widespread reach and impact of evidence-based care. Data from this line of research to date are promising, and underscore the potential public health impact of technology-based therapeutic tools. To fully realize the potential of technology-delivered interventions, several areas of inquiry remain important. First, scientifically sound strategies should be explored to ensure technology-based interventions are optimally designed to produce maximal behavior change. Second, efficient and effective methods should be identified to integrate technology-based interventions into systems of care in a manner that is most responsive to the needs of individual users. Third, payment, privacy, and regulatory systems should be refined and extended to go beyond electronic medical records and telehealth/distance care models, and support the deployment of technology-based systems to enhance the quality, efficiency and cost-effectiveness of care. Fourth, the mechanisms underlying behavior change derived from technology-based treatments should be explicated, including new mechanisms that may be tapped via novel, technology-based tools. Such work will be critical in isolating mechanisms that are useful in predicting treatment response, and in ensuring that key ingredients are present in technology-based interventions as they are made widely available.

Evaluation of Crops Sensitivity to Atrazine Soil Residual

Directory of Open Access Journals (Sweden)

E Izadi

2012-02-01

Full Text Available Abstract In order to study the sensitivity of 9 crops to atrazine soil residual, two separate experiments were conducted in field and greenhouse conditions. First experiment was conducted in a field with treated soil by atrazine based on split plot and the results evaluated in greenhouse conditions. Treatments in the field experiment included two organic manure application rates (0 and 50 t/ha as main plots and 2 atrazine application rates (2 and 4 kg/ha atrazine a.i. as sob plots. After corn harvesting soil was sampled at 0-15 cm surface layer in each plots in 15 points, after mixing the samples. Wheat, barley, sugar beet, pea, lens and colza planted in pots at greenhouse. Second experiment conducted in greenhouse conditions for evaluation of atrazine soil residual in completely randomized design. Treatments included atrazine soil residual concentrations (0, 0.2, 0.5, 1, 5, 10 and 15 mg/kg soil and crops included wheat, barley, sugar beet, pea, lens, rape, bean and tomato. Results showed that atrazine residue had no effect on crops growth in field experiment treated with atrazine. It seems that atrazine residue in filed soil is lower that its damage threshold for crops or maybe for its fast removal in field than in control conditions. But in bioassay experiment (greenhouse experiment crops response to atrazine residues were different. Results showed that onion and pea were most susceptible ant tolerant crops between studied species and based of ED50 parameter the other crops tolerance to total residue ranked as: pea< bean< lentil< sugar beet< tomato< barley< wheat< rape< onion. Keywords: Atrazine residue, Pea, Bean, Lentil, Sugar beet, Barley, Wheat, Rape, Tomato

WATER MICROPOLLUTANTS: CLASSIFICATION AND TREATMENT TECHNOLOGIES

Directory of Open Access Journals (Sweden)

Yolanda Patiño

2014-06-01

Full Text Available This article reviews the different kinds of emerging contaminants, their origin and use, and their presence in the Spanish waters, both in surface and groundwater. Micropollutants are compounds of different origin and chemical nature which had been unnoticed (due to their low concentration and don’t have specific regulation. They are divided into six major groups, and many of them behave as endocrine disruptors causing large negative effects on human health and environment. They are in waters because the waste water treatment plants are not designed for their removal, so they are being discharged. Different alternatives for their removal are discussed - physico- chemical, biological and hybrid treatment technologies -. Among the physicochemical process, the advance oxidation processes (AOPs are very promising.

Four weeks of treatment with liraglutide reduces insulin dose without loss of glycemic control in type 1 diabetic patients with and without residual beta-cell function

DEFF Research Database (Denmark)

Kielgast, Urd; Krarup, Thure; Holst, Jens Juul

2011-01-01

OBJECTIVE To investigate the effect of 4 weeks of treatment with liraglutide on insulin dose and glycemic control in type 1 diabetic patients with and without residual ß-cell function. RESEARCH DESIGN AND METHODS Ten type 1 diabetic patients with residual ß-cell function (C-peptide positive) and 19.......1]; P Treatment with liraglutide in type 1 diabetic patients reduces insulin dose with improved or unaltered glycemic control....... activity was performed before (week 0) and during (week 4) treatment. Differences in insulin dose; HbA(1c); time spent with blood glucose 10, and 3.9-9.9 mmol/L; and body weight were evaluated. RESULTS Insulin dose decreased from 0.50 ± 0.06 to 0.31 ± 0.08 units/kg per day (P

Preferency of soil macrofauna to crops residue at different light intensity

Directory of Open Access Journals (Sweden)

SUGIYARTO

2007-10-01

Full Text Available Every species of soil macrofauna prefer specific food and environment to be establish in it's habitat. Their diversity depend on variation of food and environmental condition. The aim of this research was to study the effect of different crop residue and light intensity on population of several soil macrofauna specieses. Mycrocosmos experiment was arranged in split-plot design with two treatments factor, i.e.: (1 crop residue (albizia, papaya, elephant grass, maize, sweet potato and without crop residue input, and (2 light intensities (0, 5, 15 and 25 Watt/day. The soil macrofauna were earthworms, millipedes, scarabids larvae and cocroachs. Results of the study showed that: (1 crop residues apllication increased soil macrofauna population, especially maize residue ( by 113%, respectively, compare to control tretment, (2 on higher light intensity, population of earthworms, scarabids larvae and cocroach decreased, but population of millipedes increased, (3 the highest macrofauna population was on maize residue and 5 Watt/day light intensity treatment.

Rapid Detection Technology for Pesticides Residues Based on Microelectrodes Impedance Immunosensor

Directory of Open Access Journals (Sweden)

Wen Ping Zhao

2014-09-01

Full Text Available Compared with conventional methods, electrochemical immunosensors have many advantages, such as low cost, high sensitivity, and rapid detection, and has certain prospects for realizing real-time-monitoring. In this paper, a design of portable pesticide residues detection instrument was presented based on an electrochemical impedance immunosensor. Firstly, we studied on an impedance immunosensor based on interdigitated array microelectrode (IDAM coupled with magnetic nanobeads-antibody conjugates (MNAC for the pesticide detection. Magnetic nanobeads (diameter 150 nm coated with anti-carbofuran antibodies were used for further amplification of the binding reaction between antibody and hapten (carbofuran. Secondly, in order to develop a portable pesticide residue apparatus, we designed the impedance detection electric circuit. Main work included designing and constructing of the system circuit, designing and debugging of the system software and so on. Thirdly, the apparatus was used for the standard pesticides solutions testing combined with immunosensor to test the reliability and stability. The pesticide added standard recovery was more than 70 % and the impedance test error was less than 5 %. The results showed that the proposed instrument had a good consistence compared with the traditional analytical methods. Thus, it would be a promising rapid detection instrument for pesticide residues in agricultural products.

FE-simulation of hot forging with an integrated heat treatment with the objective of residual stress prediction

Science.gov (United States)

Behrens, Bernd-Arno; Chugreeva, Anna; Chugreev, Alexander

2018-05-01

Hot forming as a coupled thermo-mechanical process comprises numerous material phenomena with a corresponding impact on the material behavior during and after the forming process as well as on the final component performance. In this context, a realistic FE-simulation requires reliable mathematical models as well as detailed thermo-mechanical material data. This paper presents experimental and numerical results focused on the FE-based simulation of a hot forging process with a subsequent heat treatment step aiming at the prediction of the final mechanical properties and residual stress state in the forged component made of low alloy CrMo-steel DIN 42CrMo4. For this purpose, hot forging experiments of connecting rod geometry with a corresponding metallographic analysis and x-ray residual stress measurements have been carried out. For the coupled thermo-mechanical-metallurgical FE-simulations, a special user-defined material model based on the additive strain decomposition method and implemented in Simufact Forming via MSC.Marc solver features has been used.

Hydrothermal treatment followed by enzymatic hydrolysis and hydrothermal carbonization as means to valorise agro- and forest-based biomass residues.

Science.gov (United States)

Wikberg, Hanne; Grönqvist, Stina; Niemi, Piritta; Mikkelson, Atte; Siika-Aho, Matti; Kanerva, Heimo; Käsper, Andres; Tamminen, Tarja

2017-07-01

The suitability of several abundant but underutilized agro and forest based biomass residues for hydrothermal treatment followed by enzymatic hydrolysis as well as for hydrothermal carbonization was studied. The selected approaches represent simple biotechnical and thermochemical treatment routes suitable for wet biomass. Based on the results, the hydrothermal pre-treatment followed by enzymatic hydrolysis seemed to be most suitable for processing of carbohydrate rich corn leaves, corn stover, wheat straw and willow. High content of thermally stable components (i.e. lignin) and low content of ash in the biomass were advantageous for hydrothermal carbonization of grape pomace, coffee cake, Scots pine bark and willow. Copyright © 2017 Elsevier Ltd. All rights reserved.

Wastes to Resources: Appropriate Technologies for Sewage Treatment and Conversion.

Science.gov (United States)

Anderson, Stephen P.

Appropriate technology options for sewage management systems are explained in this four-chapter report. The use of appropriate technologies is advocated for its health, environmental, and economic benefits. Chapter 1 presents background information on sewage treatment in the United States and the key issues facing municipal sewage managers.…

Efficiency in the reduction of chromium by a wild bacterium in a Batch treatment type using residual water substrate from the municipality of Pasto, Colombia

Directory of Open Access Journals (Sweden)

Deisy Lorena Guerrero Ceballos

2017-05-01

Full Text Available Objective: To evaluate the efficiency in the reduction of chromium in a Batch treatment type, using municipal residual water substrate inoculated with a wild bacterium. Materials and methods: The reduction percentage of hexavalent chromium of three wild bacteria previously isolated from residual water from the Pasto River was verified at laboratory scale (Bacillus thuringiensis, Bacillus amyloliquefaciens and Paenibacillus sp.; the isolated that showed the highest percentage of reduction of Cr was selected and was subjected to different treatments. The analysis of results was done using descriptive statistics. Results: B. thuringiensis, B. amyloliquefaciens, and Paenibacillus sp., presented percentages of reduction of Cr (VI of 82,01%; 80,85% and 79,27%, respectively. It was determined that the third treatment (nonsterile water from the Pasto River with B. thuringiensis presented significant differences with regard to the other (p = 0.0001 α = 0.05, concluding that B. thuringiensis reduces in greater proportion the Cr (VI. The results found in this research are promising in the field of bioremediation of contaminated effluents with Chrome since they may be taken as the basis for implementing strategies of bioremediation on a large scale. Conclusion: The bacteria B. thuringiensis presented high efficiency in the reduction of hexavalent chromium (99.42% when implemented in a treatment at laboratory scale of residual nonsterile water.

EFFECT OF POST-LOGGING SILVICULTURAL TREATMENT ON GROWTH RATES OF RESIDUAL STAND IN A TROPICAL FOREST

Directory of Open Access Journals (Sweden)

Haruni Krisnawati

2010-12-01

Full Text Available Post-logging silvicultural treatments are generally performed to improve yields of the remaining tree species by increasing their growth rate. In this study the effects of silvicultural treatment on the growth rates of commercial (dipterocarps and non-dipterocarps as well as non- commercial tree species in a tropical forest in West Kalimantan were examined and were compared to a control treatment. Silvicultural treatment applied was liberation of future crop trees from lianas and neighbouring competing trees. Treatments were applied to six plots of 80 m x 80 m each. The plots comprised 64 quadrats of 10 m x 10 m to allow better control of measurements. The treatment and control plots were established 6 years after logging. Effects were measured 2,4 and 7 years after treatment application. In all obser vation periods, the growth rates increased with silvicultural treatment. Overall, commercial dipterocarps, commercial non-dipterocarps and non-commercial tree species groups differed in response to silvicultural treatment. The growth rates of commercial tree species in plots that received silvicultural treatment were 62–97% higher than in the control plots. For non-commercial tree species, the increase of growth rates was 20–58%, compared to the control plots. These results indicate that the application of silvicultural treatments after logging could help improve the growth of the residual stands. These provide quantitative information that silvicultural treatments in logged-over forest should be considered as a viable management option and may guide the choice of cutting cycle.

Quality of diets with fludized bed combustion residue treatment: II. Swine trials

Energy Technology Data Exchange (ETDEWEB)

Whitsel, T.J.; Reid, R.L.; Stout, W.L.; Hern, J.L.; Bennett, O.L.

Growing pigs (Sus scrofa domesticus) were fed for an 8-wk period in two trials on diets produced on soils treated with fluidized bed combustion residue (FBCR) or limestone. Diets contained corn (Zea mays L.) and wheat (Triticum aestivum L.) mixtures with soybean (Glycine max (L.) Merr.) meal, supplemented with vegetables, fruits, and meat. Pigs were fed ad libitum and effects of diet treatment on rate of gain, N balance, blood composition, and element composition of the carcass and organs were determined. The FBCR diet caused a decrease (P<0.05 in Trial 1, P <0.07 in Trial 2) in body weight gains of pigs, but increased (P<0.05) N retention in one trial. Blood composition was not influenced markedly by diet treatment, with small but significant differences in serum Ca, triglycerides, certain amino acids, and whole blood Pb concentrations; effects were not consistent between trials. Urinary As concentration was slightly higher for pigs on FBCR diets. Analysis of the carcass and organs of pigs slaughtered posttrial showed significant differences in element levels from those of pretrial animals, but differences in tissue mineral concentrations related to diet treatment were few and inconsistent. Element concentrations in the organs of pigs were within normal ranges. No explanation for the depression in weight gain of pigs fed FBCR-treated diets was found. Except for the weight response, results support data from other trials with laboratory animals showing no apparent adverse effects of FBCR application to soils on nutritive quality of foods. 24 refs., 1 fig., 10 tabs.

Plasmarc technology for the treatment of metallic radwaste

International Nuclear Information System (INIS)

Hoffelner, W.; Weigel, H.

1999-01-01

The Plasmarc incineration and melting technology is suitable for processing radioactive wastes arising from the fields of medicine, industry and research, and from the operation and maintenance of nuclear power plants. Combustible wastes can be thermally decomposed and metals melted in the same facility together, and the incineration products and metals are thus turned into a form suitable for disposal in one step. In secondary metallurgy the Plasmarc technology can be used for melting scrap metal and recovering usable metals from metalliferous wastes, particularly composites of different metals and ceramics and metals and plastics. In the case of special wastes, it is possible to thermally decompose otherwise problematic residues in an oxygen free atmosphere at high temperatures. Material construction in the incineration mode could be in 200-litre standard drums with a total weight up to 300 kilograms if an average processing efficiency of 200 kilograms of mixed waste per hours is assumed. Melting: In the melting mode for metals, the drums coming from the storage rack are placed in the slowly rotating furnace using a grabbing device. Because of the low speed of rotation, the central outlet is initially blocked with a stopper. The drums, with contents, are then molten in the plasma arc. As soon as there is a melted mass, the speed of rotation of the furnace is increased until there is no material outflow when the stopper is removed. The stopped is then removed and the speed of rotation is reduced once again to allow the melt to flow out, exactly as in the incineration mode. Mixing: In the mixing mode, metallic/nonmetallic mixtures (e.g. reinforced concrete) can be processed. The meltable components are melted and the organic components are thermally decomposed. Because of differences in density, the inorganic residues float on the surface of the molten metal and can be vitrified using additives. These different operating modes of the Plasmarc furnace allow various

Assisted reproductive technology (ART) treatment in women with schizophrenia or related psychotic disorder

DEFF Research Database (Denmark)

Ebdrup, Ninna H; Assens, Maria; Hougaard, Charlotte O

2014-01-01

To determine the prevalence rate of women with a diagnosis of schizophrenia or related psychotic disorder in assisted reproductive technology (ART) treatment and to study these women's fertility treatment outcome in comparison to women with no psychotic disorders.......To determine the prevalence rate of women with a diagnosis of schizophrenia or related psychotic disorder in assisted reproductive technology (ART) treatment and to study these women's fertility treatment outcome in comparison to women with no psychotic disorders....

Treatment and immobilization of intermediate-level radioactive wastes

International Nuclear Information System (INIS)

Lerch, R.E.; Greenhalgh, W.O.; Partridge, J.A.; Richardson, G.L.

1979-01-01

A new program underway at the Hanford Engineering Development Laboratory (HEDL) to develop and demonstrate treatment and immobilization technologies for intermediate-level wastes (ILW) generated in the nuclear fuel cycle is discussed. ILW are defined as those liquid and solid radioactive wastes, other than high-level wastes and fuel cladding hulls, that in packaged form have radiation dose readings greater than 200 millirem/hr at the packaged surface and 10 millirem/hr at three feet from the surface. The IAEA value of 10 4 Ci/m 3 for ILW defines the upper limit. For comparative purposes, reference is also made to certain aspects of low-level radioactive wastes (LLW). Initial work has defined the sources, quantities and types of wastes which comprise ILW. Because of the wide differences in composition (e.g., acids, salt solutions, resins and zeolites, HEPA filters, etc.) the wastes may require different treatments, particularly those wastes containing volatile contaminants. The various types of ILW have been grouped into categories amenable to similar treatment. Laboratory studies are underway to define treatment technologies for liquid ILW which contain volatile contaminants and to define immobilization parameters for the residues resulting from treatment of ILW. Immobilization agents initially being evaluated for the various residues include cement, urea-formaldehyde, and bitumen although other immobilization agents will be studied. The program also includes development of acceptable test procedures for the final immobilized products as well as development of proposed criteria for storage, transportation, and disposal of the immobilized ILW

Responses of Pea (Pisum sativum Growth and Yield to Residual Effects of Organic and Urea Fertilizers from Previous Crop

Directory of Open Access Journals (Sweden)

S. Fallah

2016-07-01

Full Text Available Application of organic manure in organic farming and long-term mineralization may lead to residual effects on the succeeding crop. So, residual effects of combined cattle manure and urea fertilizer of previous crop (black cumin on growth and yield of pea were examined in a randomized complete block design. Treatments included of  cattle manure (CM, urea (U, three ratios of CM+U full dose application (2:1; 1:1; 1:2 and three ratios of CM+U split application (2:1; 1:1; 1:2, and unfertilized control to previous crop (black cumin in 2012. Pea planted without any fertilizer in 2013. There was no significant difference between control and residual of urea treatment for some parameters including dry matter in flowering stage, plant nitrogen and phosphorus concentration, plant height, yield components, grain yield and biological yield of pea. Biological and grain yields were greater under both residual of cattle manure treatment and integrated treatments compared to residual of urea treatment. The highest grain yield (4000 kg ha-1 was observed in residual of CM:U full dosed application treatment, to the extent that grain yield in this treatment indicated a 1.5-fold increase in comparison with residual of urea treatment. The highest biological yield (8325 kg ha-1 was obtained in residual of CM treatment, though it was not significant different from that of residual of CM:U (1:2 treatments. In general, although residual of urea fertilizer did not leave a notable effect on pea production, but production of this crop relying on residual of cattle manure deems effective to lowering of fertilization cost and ameliorating environmental contaminations.

Evaluating the technical aspects of mixed waste treatment technologies

International Nuclear Information System (INIS)

Bagaasen, L.M.; Scott, P.A.

1992-10-01

This report discusses treatment of mixed wastes which is thought to be more complicated than treatment of either hazardous or radioactive wastes. In fact, the treatment itself is no more complicated: however, the regulations that define acceptability of the final waste disposal system are significantly more entangled, and sometimes in apparent conflict. This session explores the factors that influence the choice of waste treatment technologies, and expands on some of the limitations to their application. The objective of the presentation is to describe the technical factors that influence potential treatment processes and the ramifications associated with particular selections (for example, the generation of secondary waste streams). These collectively provide a framework for making informed treatment process selections

Logging residues under different stand and harvesting conditions, Rocky Mountains

Science.gov (United States)

Robert E. Benson; Cameron M. Johnston

1976-01-01

Volume and characteristics of logging residues from 34 harvest areas are presented. Clearcuts and partial cuts logged to conventional utilization levels and to close utilization levels are included. Residue volumes ranged from almost 3, 600 ft3 /acre of wood 3-inches-plus down to about 550 ft3 /acre, depending on treatment. More than 60 percent of the residues were...

Washing effects of limonene on pesticide residues in green peppers.

Science.gov (United States)

Lu, Hai-Yan; Shen, Yan; Sun, Xing; Zhu, Hong; Liu, Xian-Jin

2013-09-01

The presence of pesticide residues in food has caused much concern. The low health risks and environmental impacts of limonene make it a very interesting solvent for use in green chemistry. Washing effects of limonene on pesticide residues of methyl chlorpyrifos, chlorothalonil, chlorpyrifos, fenpropathrin and deltamethrin were investigated in green pepper. Results showed that washing with a low concentration of limonene for 5 min (where LOQ is limit of quantitation) caused 53.67%, limonene for 10 min produced 55.90%, limonene for 5 min was the optimal treatment for elimination of pesticide residues in green pepper, considering effect and treatment time as well as cost. © 2013 Society of Chemical Industry.

The Effect of Processing on 14C- Chlofenvinphos Residues in Maize Oil and Bioavailability of its Cake Residues on Rats

International Nuclear Information System (INIS)

Mahdy, F.; El-Maghraby, S.

2008-01-01

Maize seed obtained from 14 C-chlofenvinphos treated plants contained 0.12 % of the applied dose. The insecticide residues in crude oil, methanol and coke amounted to 10 %, 6 % and 69 %, respectively of original residues inside the seeds.The 14 C activity in the crude oil could be a gradual reduced by the refining processes. The alkali treatment and bleaching steps are more effective steps in the refining processes remove about (63 %). The refined oil contained only about 17 % of the 14 C-residues originally present. The major residues in processed oil contain parent compound, in addition to five metabolites of the insecticide. When rats fed the extracted seeds (cake), the bound residues were found to be considerably bioavailable. After feeding rats for 5 days with the cake, a substantial amount of 14 C-residues was eliminated in the urine (59.5 %), while about 20 % was excreted in the feces. About 15 % of the radioactivity was distribution among various organs