Residual stresses due to weld repairs, cladding and electron beam welds and effect of residual stresses on fracture behavior. Annual report, September 1, 1977--November 30, 1978

International Nuclear Information System (INIS)

Rybicki, E.F.

1978-11-01

The study is divided into three tasks. Task I is concerned with predicting and understanding the effects of residual stresses due to weld repairs of pressure vessels. Task II examines residual stresses due to an electron beam weld. Task III addresses the problem of residual stresses produced by weld cladding at a nozzle vessel intersection. The objective of Task I is to develop a computational model for predicting residual stress states due to a weld repair of pressure vessel and thereby gain an understanding of the mechanisms involved in the creation of the residual stresses. Experimental data from the Heavy Section Steel Technology (HSST) program at Oak Ridge National Laboratories (ORNL) is used to validate the computational model. In Task II, the residual stress model is applied to the case of an electron beam weld of a compact tension freacture specimen. The results in the form of residual stresses near the weld are then used to explain unexpected fracture behavior which is observed in the testing of the specimen. For Task III, the residual stress model is applied to the cladding process used in nozzle regions of nuclear pressure vessels. The residual stresses obtained from this analysis are evaluated to determine their effect on the phenomena of under-clad cracking

Effect of soil-bound residues of malathion on microbial activities

International Nuclear Information System (INIS)

Hussain, A.; Iqbal, Z.; Asi, M.R.; Tahira, R.; Chudhary, J.A.

2001-01-01

The effect of soil-bound residues of malathion on CO/sub 2/ evolution, dehydrogenase activity and some nitrogen transformations in a loam soil was investigated under laboratory conditions. The soil samples containing bound residues arising from 10 mg g-1 of the applied malathion were mixed in equal quantity with fresh soil and compared with solvent extracted control soil without bound residues (extracted in the same way as soil containing bound residues). Another control comprising un extracted fresh soil without bound residues was also kept to study the effect of solvent extraction on the biological activity. Rate of Carbon mineralization (CO/sub 2/ evolution) was decreased in the presence of soil-bound residues of malathion. Bound residues also affected dehydrogenase activity of soil. Over 40% inhibition of dehydrogenase activity was observed after 4 days and the inhibition persisted at least for 12 days. Nitrogen mineralization was stimulated in soil containing bound residues of malathion and this stimulatory effect increased with time of incubation. Nitrification was partially inhibited in the presence of soil-bound residues of malathion. The inhibitory effect of the soil-bound residues on nitrification did not show much variation with time. The soil-bound residues did not affect denitrification rate (N/sub 2/O evolution). Nitrogen fixation (acetylene reduction) was partially inhibited in soil amended with bound residues of malathion and the inhibitory effect persisted for at least one week. In general, soil bound residues of malathion inhibited CO/sub 2/ evolution, dehydrogenase activity, nitrification and nitrogen fixation while mineralization of nitrogen was stimulated. Denitrification was not affected by the applied insecticide. (author)

Spin distribution of evaporation residues formed in complete and incomplete fusion in 16O+154Sm system

Science.gov (United States)

Singh, D.; Linda, Sneha B.; Giri, Pankaj K.; Mahato, Amritraj; Tripathi, R.; Kumar, Harish; Afzal Ansari, M.; Sathik, N. P. M.; Ali, Rahbar; Kumar, Rakesh; Muralithar, S.; Singh, R. P.

2017-11-01

Spin distributions for several evaporation residues populated in the 16O+154Sm system have been measured at projectile energy ≈ 6.2 MeV/A by using the charged particle-γ-coincidence technique. The measured spin distributions of the evaporation residues populated through incomplete fusion associated with 'fast' α and 2α-emission channels are found to be entirely different from fusion-evaporation channels. It is observed that the mean input angular momentum for the evaporation residues formed in incomplete fusion channel is relatively higher than that observed for evaporation residues in complete fusion channels. The feeding intensity profile of evaporation residues populated through complete fusion and incomplete fusion have also been studied. The incomplete fusion channels are found to have narrow range feeding only for high spin states, while complete fusion channels are strongly fed over a broad spin range and widely populated. Comparison of present results with earlier data suggests that the mean input angular momentum values are relatively smaller for spherical target than that of deformed target using the same projectile and incident energy highlighting the role of target deformation in incomplete fusion dynamics.

Spin distribution of evaporation residues formed in complete and incomplete fusion in 16O+154Sm system

Directory of Open Access Journals (Sweden)

D. Singh

2017-11-01

Full Text Available Spin distributions for several evaporation residues populated in the 16O+154Sm system have been measured at projectile energy ≈ 6.2 MeV/A by using the charged particle–γ-coincidence technique. The measured spin distributions of the evaporation residues populated through incomplete fusion associated with ‘fast’ α and 2α-emission channels are found to be entirely different from fusion–evaporation channels. It is observed that the mean input angular momentum for the evaporation residues formed in incomplete fusion channel is relatively higher than that observed for evaporation residues in complete fusion channels. The feeding intensity profile of evaporation residues populated through complete fusion and incomplete fusion have also been studied. The incomplete fusion channels are found to have narrow range feeding only for high spin states, while complete fusion channels are strongly fed over a broad spin range and widely populated. Comparison of present results with earlier data suggests that the mean input angular momentum values are relatively smaller for spherical target than that of deformed target using the same projectile and incident energy highlighting the role of target deformation in incomplete fusion dynamics.

Characterization of Residual Stress Effects on Fatigue Crack Growth of a Friction Stir Welded Aluminum Alloy

Science.gov (United States)

Newman, John A.; Smith, Stephen W.; Seshadri, Banavara R.; James, Mark A.; Brazill, Richard L.; Schultz, Robert W.; Donald, J. Keith; Blair, Amy

2015-01-01

An on-line compliance-based method to account for residual stress effects in stress-intensity factor and fatigue crack growth property determinations has been evaluated. Residual stress intensity factor results determined from specimens containing friction stir weld induced residual stresses are presented, and the on-line method results were found to be in excellent agreement with residual stress-intensity factor data obtained using the cut compliance method. Variable stress-intensity factor tests were designed to demonstrate that a simple superposition model, summing the applied stress-intensity factor with the residual stress-intensity factor, can be used to determine the total crack-tip stress-intensity factor. Finite element, VCCT (virtual crack closure technique), and J-integral analysis methods have been used to characterize weld-induced residual stress using thermal expansion/contraction in the form of an equivalent delta T (change in local temperature during welding) to simulate the welding process. This equivalent delta T was established and applied to analyze different specimen configurations to predict residual stress distributions and associated residual stress-intensity factor values. The predictions were found to agree well with experimental results obtained using the crack- and cut-compliance methods.

Determination of Pesticides Residues in Cucumbers Grown in Greenhouse and the Effect of Some Procedures on Their Residues.

Science.gov (United States)

Leili, Mostafa; Pirmoghani, Amin; Samadi, Mohammad Taghi; Shokoohi, Reza; Roshanaei, Ghodratollah; Poormohammadi, Ali

2016-11-01

The objective of this study was to determine the residual concentrations of ethion and imidacloprid in cucumbers grown in greenhouse. The effect of some simple processing procedures on both ethion and imidacloprid residues were also studied. Ten active greenhouses that produce cucumber were randomly selected. Ethion and imidacloprid as the most widely used pesticides were measured in cucumber samples of studied greenhouses. Moreover, the effect of storing, washing, and peeling as simple processing procedures on both ethion and imidacloprid residues were investigated. One hour after pesticide application; the maximum residue levels (MRLs) of ethion and imidacloprid were higher than that of Codex standard level. One day after pesticide application, the levels of pesticides were decreased about 35 and 31% for ethion and imidacloprid, respectively, which still were higher than the MRL. Washing procedure led to about 51 and 42.5% loss in ethion and imidacloprid residues, respectively. Peeling procedure also led to highest loss of 93.4 and 63.7% in ethion and imidacloprid residues, respectively. The recovery for both target analytes was in the range between 88 and 102%. The residue values in collected samples one hour after pesticides application were higher than standard value. The storing, washing, and peeling procedures lead to the decrease of pesticide residues in greenhouse cucumbers. Among them, the peeling procedure has the greatest impact on residual reduction. Therefore, these procedures can be used as simple and effective processing techniques for reducing and removing pesticides from greenhouse products before their consumption.

comparative assessment residual soils in residual soils in parts of e

African Journals Online (AJOL)

eobe

residual soil formed from Zuma rock. The Zuma r is an igneous .... The liquid limit (LL) is the lowest water content above which soil .... where this effect begins to be counteracted by the saturation of the ... retaining walls, tunnel linings and timbering of excavation. .... event of pore pressure build up due to excessive moisture.

Effect of laser energy on the deformation behavior in microscale laser bulge forming

International Nuclear Information System (INIS)

Zheng Chao; Sun Sheng; Ji Zhong; Wang Wei

2010-01-01

Microscale laser bulge forming is a high strain rate microforming method using high-amplitude shock wave pressure induced by pulsed laser irradiation. The process can serve as a rapidly established and high precision technique to impress microfeatures on thin sheet metals and holds promise of manufacturing complex miniaturized devices. The present paper investigated the forming process using both numerical and experimental methods. The effect of laser energy on microformability of pure copper was discussed in detail. A 3D measuring laser microscope was adopted to measure deformed regions under different laser energy levels. The deformation measurements showed that the experimental and numerical results were in good agreement. With the verified simulation model, the residual stress distribution at different laser energy was predicted and analyzed. The springback was found as a key factor to determine the distribution and magnitude of the compressive residual stress. In addition, the absorbent coating and the surface morphology of the formed samples were observed through the scanning electron microscope. The observation confirmed that the shock forming process was non-thermal attributed to the protection of the absorbent coating.

Relocation of radioactive residuals store: environment effects statement

International Nuclear Information System (INIS)

1984-11-01

This Environment Effects Statement describes and assesses the likely environmental effects of the proposal to relocate the Health Commission's existing radioactive residuals store to a site within the established Dutson Downs waste disposal area, located 20 km south-east of Sale and 225 km east of Melbourne. The information presented demonstrates that the siting and construction of the proposed radioactive residuals store and the procedures to be adopted for the handling and storage of materials will not present an unacceptable risk to public health and safety, nor will it involve any significant adverse environmental effects

Residual effects of hypnotics: an update.

Science.gov (United States)

Hindmarch, I

1991-07-01

The sedative/hypnotic benzodiazepines introduced worldwide in the early 1960s were acclaimed for their low chemical toxicity and safety in clinical use. A decade later, some researchers and clinicians found that while all the drugs had undoubted potency and efficacy as sleep inducers and maintainers, the trade-off in residual effects (e.g., excessive daytime tiredness, poor concentration, impaired psychomotor performance, lowered mental abilities) was cause for concern. These sequelae not only affected patients' safety and ability to perform daytime tasks, but were also counter-therapeutic; the daytime sleep that was produced interfered with the natural nocturnal sleep. In a recent study, the degree to which patient abilities were impaired was measured by a number of psychomotor tests. Benzodiazepines with a duration of clinical effect of less than 8 to 10 hours produced fewer, less frequent residual effects than those with a measurable activity in excess of the normal nocturnal sleep period.

Evidence for a Proton Transfer Network and a Required Persulfide-Bond-Forming Cysteine Residue in Ni-Containing Carbon Monoxide Dehydrogenases

International Nuclear Information System (INIS)

Eun Jin Kim; Jian Feng; Bramlett, Matthew R.; Lindahl, Paul A.

2004-01-01

OAK-B135 Carbon monoxide dehydrogenase from Moorella thermoacetica catalyzes the reversible oxidation of CO to CO2 at a nickel-iron-sulfur active-site called the C-cluster. Mutants of a proposed proton transfer pathway and of a cysteine residue recently found to form a persulfide bond with the C-cluster were characterized. Four semi-conserved histidine residues were individually mutated to alanine. His116 and His122 were essential to catalysis, while His113 and His119 attenuated catalysis but were not essential. Significant activity was ''rescued'' by a double mutant where His116 was replaced by Ala and His was also introduced at position 115. Activity was also rescued in double mutants where His122 was replaced by Ala and His was simultaneously introduced at either position 121 or 123. Activity was also ''rescued'' by replacing His with Cys at position 116. Mutation of conserved Lys587 near the C-cluster attenuated activity but did not eliminate it. Activity was virtually abolished in a double mutant where Lys587 and His113 were both changed to Ala. Mutations of conserved Asn284 also attenuated activity. These effects suggest the presence of a network of amino acid residues responsible for proton transfer rather than a single linear pathway. The Ser mutant of the persulfide-forming Cys316 was essentially inactive and displayed no EPR signals originating from the C-cluster. Electronic absorption and metal analysis suggests that the C-cluster is absent in this mutant. The persulfide bond appears to be essential for either the assembly or stability of the C-cluster, and/or for eliciting the redox chemistry of the C-cluster required for catalytic activity

Effects of Bio-char on Soil Microbes in Herbicide Residual Soils

Directory of Open Access Journals (Sweden)

WANG Gen-lin

2015-10-01

Full Text Available Effects of biological carbon (bio-char on soil microbial community were studied by pot experiments simulating long residual herbicide residues in soil environment, which clarifed the improvement of biochar and its structural properties on soil microenvironment. The results showed that fungi and actinomycetes had the same effect tendency within 0~0.72 mg·kg-1 in clomazone residue which increased the role of stimulation with crop growth process prolonged, especially in high residue treatment, but strong inhibitory effect on bacteria community was occured early which returned to normal until sugar beet growth to fiftieth day. Soil fungi community decreased with bio-char adding, but had no significant difference with the control. When clomazone residue in soil was below 0.24 mg·kg-1, soil actinomycetes community was higher than control without bio-char, bacteria increased first and then reduced after adding carbon as below 0.12 mg·kg-1. Biochar was ‘deep hole’ structure containing C, O, S and other elements. The results showed that a certain concentration clomazone residue in soil would stimulate soil fungi and actinomycetes to grow. After adding the biochar, the inhibition effect of high herbicides residual on bacterial would be alleviated.

Technical note: Equivalent genomic models with a residual polygenic effect.

Science.gov (United States)

Liu, Z; Goddard, M E; Hayes, B J; Reinhardt, F; Reents, R

2016-03-01

Routine genomic evaluations in animal breeding are usually based on either a BLUP with genomic relationship matrix (GBLUP) or single nucleotide polymorphism (SNP) BLUP model. For a multi-step genomic evaluation, these 2 alternative genomic models were proven to give equivalent predictions for genomic reference animals. The model equivalence was verified also for young genotyped animals without phenotypes. Due to incomplete linkage disequilibrium of SNP markers to genes or causal mutations responsible for genetic inheritance of quantitative traits, SNP markers cannot explain all the genetic variance. A residual polygenic effect is normally fitted in the genomic model to account for the incomplete linkage disequilibrium. In this study, we start by showing the proof that the multi-step GBLUP and SNP BLUP models are equivalent for the reference animals, when they have a residual polygenic effect included. Second, the equivalence of both multi-step genomic models with a residual polygenic effect was also verified for young genotyped animals without phenotypes. Additionally, we derived formulas to convert genomic estimated breeding values of the GBLUP model to its components, direct genomic values and residual polygenic effect. Third, we made a proof that the equivalence of these 2 genomic models with a residual polygenic effect holds also for single-step genomic evaluation. Both the single-step GBLUP and SNP BLUP models lead to equal prediction for genotyped animals with phenotypes (e.g., reference animals), as well as for (young) genotyped animals without phenotypes. Finally, these 2 single-step genomic models with a residual polygenic effect were proven to be equivalent for estimation of SNP effects, too. Copyright © 2016 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Effect of residual stresses on hydrogen permeation in iron

International Nuclear Information System (INIS)

Mouanga, M.; Bercot, P.; Takadoum, J.

2010-01-01

The effect of residual stresses on electrochemical permeation in iron membrane was investigated. Four thermal and mechanical treatments were chosen to obtain different surface states in relation to the residual stresses. Residual stresses were determined by X-ray diffraction (XRD) using the Macherauch and Mueller method. The results were completed by the microhardness measurements. For all iron membranes, compressive residual stresses were obtained. Electrochemical permeation experiments using a Devanathan and Stachurski cell were employed to determine the hydrogen permeation behaviour of the various iron membranes. The latter was charged with hydrogen by galvanostatic cathodic polarization in 0.1 M NaOH at 25 deg. C. The experimental results revealed that hydrogen permeation rate increases with increasing residual stresses introduced in iron membranes.

Handling of Solid Residues

International Nuclear Information System (INIS)

Medina Bermudez, Clara Ines

1999-01-01

The topic of solid residues is specifically of great interest and concern for the authorities, institutions and community that identify in them a true threat against the human health and the atmosphere in the related with the aesthetic deterioration of the urban centers and of the natural landscape; in the proliferation of vectorial transmitters of illnesses and the effect on the biodiversity. Inside the wide spectrum of topics that they keep relationship with the environmental protection, the inadequate handling of solid residues and residues dangerous squatter an important line in the definition of political and practical environmentally sustainable. The industrial development and the population's growth have originated a continuous increase in the production of solid residues; of equal it forms, their composition day after day is more heterogeneous. The base for the good handling includes the appropriate intervention of the different stages of an integral administration of residues, which include the separation in the source, the gathering, the handling, the use, treatment, final disposition and the institutional organization of the administration. The topic of the dangerous residues generates more expectation. These residues understand from those of pathogen type that are generated in the establishments of health that of hospital attention, until those of combustible, inflammable type, explosive, radio-active, volatile, corrosive, reagent or toxic, associated to numerous industrial processes, common in our countries in development

Radiation effects on residual voltage of polyethylene films

International Nuclear Information System (INIS)

Kyokane, Jun; Park, Dae-Hee; Yoshino, Katsumi.

1986-01-01

It has recently been pointed out that diagnosis of deterioration in insulating materials for electric cables used in nuclear power plants and outer space (communications satellite in particular) can be effectively performed based on measurements of residual voltage. In the present study, polyethylene films are irradiated with γ-rays or electron beam to examine the changes in residual voltage characteristics. Irradiation of electron beam and γ-rays are carried out to a dose of 0 - 90 Mrad and 0 - 100 Mrad, respectively. Measurements are made of the dependence of residual voltage on applied voltage, electron beam and γ-ray irradiation, annealing temperature and annealing time. Results show that carriers, which are once trapped after being released from the electrode, move within the material after the opening of the circuit to produce resiual voltage. The residual voltage increases with increasing dose of electron beam or γ-ray and levels off at high dose. Residual voltage is increased about several times by either electron beam or γ-rays, but electron beam tends to cause greater residual voltage than γ-ray. Polyethylene films irradiated with electron beam can recover upon annealing. It is concluded from observations made that residual voltage has close relations with defects in molecular structures caused by radiations, particularly the breaking of backbone chains and alteration in superstructures. (Nogami, K.)

Gravitation and quadratic forms

International Nuclear Information System (INIS)

Ananth, Sudarshan; Brink, Lars; Majumdar, Sucheta; Mali, Mahendra; Shah, Nabha

2017-01-01

The light-cone Hamiltonians describing both pure (N=0) Yang-Mills and N=4 super Yang-Mills may be expressed as quadratic forms. Here, we show that this feature extends to theories of gravity. We demonstrate how the Hamiltonians of both pure gravity and N=8 supergravity, in four dimensions, may be written as quadratic forms. We examine the effect of residual reparametrizations on the Hamiltonian and the resulting quadratic form.

Gravitation and quadratic forms

Energy Technology Data Exchange (ETDEWEB)

Ananth, Sudarshan [Indian Institute of Science Education and Research,Pune 411008 (India); Brink, Lars [Department of Physics, Chalmers University of Technology,S-41296 Göteborg (Sweden); Institute of Advanced Studies and Department of Physics & Applied Physics,Nanyang Technological University,Singapore 637371 (Singapore); Majumdar, Sucheta [Indian Institute of Science Education and Research,Pune 411008 (India); Mali, Mahendra [School of Physics, Indian Institute of Science Education and Research,Thiruvananthapuram, Trivandrum 695016 (India); Shah, Nabha [Indian Institute of Science Education and Research,Pune 411008 (India)

2017-03-31

The light-cone Hamiltonians describing both pure (N=0) Yang-Mills and N=4 super Yang-Mills may be expressed as quadratic forms. Here, we show that this feature extends to theories of gravity. We demonstrate how the Hamiltonians of both pure gravity and N=8 supergravity, in four dimensions, may be written as quadratic forms. We examine the effect of residual reparametrizations on the Hamiltonian and the resulting quadratic form.

Immobilization of acid digestion residue

International Nuclear Information System (INIS)

Greenhalgh, W.O.; Allen, C.R.

1983-01-01

Acid digestion treatment of nuclear waste is similar to incineration processes and results in the bulk of the waste being reduced in volume and weight to some residual solids termed residue. The residue is composed of various dispersible solid materials and typically contains the resultant radioactivity from the waste. This report describes the immobilization of the residue in portland cement, borosilicate glass, and some other waste forms. Diagrams showing the cement and glass virtification parameters are included in the report as well as process steps and candidate waste product forms. Cement immobilization is simplest and probably least expensive; glass vitrification exhibits the best overall volume reduction ratio

Numerical analysis of drilling hole work-hardening effects in hole-drilling residual stress measurement

Science.gov (United States)

Li, H.; Liu, Y. H.

2008-11-01

The hole-drilling strain gage method is an effective semi-destructive technique for determining residual stresses in the component. As a mechanical technique, a work-hardening layer will be formed on the surface of the hole after drilling, and affect the strain relaxation. By increasing Young's modulus of the material near the hole, the work-hardening layer is simplified as a heterogeneous annulus. As an example, two finite rectangular plates submitted to different initial stresses are treated, and the relieved strains are measured by finite element simulation. The accuracy of the measurement is estimated by comparing the simulated residual stresses with the given initial ones. The results are shown for various hardness of work-hardening layer. The influence of the relative position of the gages compared with the thickness of the work-hardening layer, and the effect of the ratio of hole diameter to work-hardening layer thickness are analyzed as well.

Effect of applied stress on the compressive residual stress introduced by laser peening

International Nuclear Information System (INIS)

Sumiya, Rie; Tazawa, Toshiyuki; Narazaki, Chihiro; Saito, Toshiyuki; Kishimoto, Kikuo

2016-01-01

Peening is the process which is able to be generated compressive residual stress and is known to be effective for preventing SCC initiation and improvement of fatigue strength. Laser peening is used for the nuclear power plant components in order to prevent SCC initiation. Although it is reported that the compressive residual stress decreases due to applied stresses under general operating condition, the change of residual stress might be large under excessive loading such as an earthquake. The objectives of this study are to evaluate the relaxation behavior of the compressive residual stress due to laser peening and to confirm the surface residual stress after loading. Therefore laser peened round bar test specimens of SUS316L which is used for the reactor internals of nuclear power plant were loaded at room temperature and elevated temperature and then surface residual stresses were measured by X-ray diffraction method. In the results of this test, it was confirmed that the compressive residual stress remained after applying uniform stress larger than 0.2% proof stress, and the effect of cyclic loading on the residual stress was small. The effect of applying compressive stress on the residual stress relaxation was confirmed to be less than that of applying tensile stress. Plastic deformation through a whole cross section causes the change in the residual stress distribution. As a result, the surface compressive residual stress is released. It was shown that the effect of specimen size on residual stress relaxation and the residual stress relaxation behavior in the stress concentration region can be explained by assumed stress relaxation mechanism. (author)

Washing effects of limonene on pesticide residues in green peppers.

Science.gov (United States)

Lu, Hai-Yan; Shen, Yan; Sun, Xing; Zhu, Hong; Liu, Xian-Jin

2013-09-01

The presence of pesticide residues in food has caused much concern. The low health risks and environmental impacts of limonene make it a very interesting solvent for use in green chemistry. Washing effects of limonene on pesticide residues of methyl chlorpyrifos, chlorothalonil, chlorpyrifos, fenpropathrin and deltamethrin were investigated in green pepper. Results showed that washing with a low concentration of limonene for 5 min (where LOQ is limit of quantitation) caused 53.67%, limonene for 10 min produced 55.90%, limonene for 5 min was the optimal treatment for elimination of pesticide residues in green pepper, considering effect and treatment time as well as cost. © 2013 Society of Chemical Industry.

Residual stresses

International Nuclear Information System (INIS)

Macherauch, E.

1978-01-01

Residual stresses are stresses which exist in a material without the influence of external powers and moments. They come into existence when the volume of a material constantly changes its form as a consequence of mechanical, thermal, and/or chemical processes and is hindered by neighbouring volumes. Bodies with residual stress are in mechanical balance. These residual stresses can be manifested by means of all mechanical interventions disturbing this balance. Acoustical, optical, radiological, and magnetical methods involving material changes caused by residual stress can also serve for determining residual stress. Residual stresses have an ambivalent character. In technical practice, they are feared and liked at the same time. They cause trouble because they can be the cause for unexpected behaviour of construction elements. They are feared since they can cause failure, in the worst case with catastrophical consequences. They are appreciated, on the other hand, because, in many cases, they can contribute to improvements of the material behaviour under certain circumstances. But they are especially liked for their giving convenient and (this is most important) mostly uncontrollable explanations. For only in very few cases we have enough knowledge and possibilities for the objective evaluation of residual stresses. (orig.) [de

On the role of the residual stress state in product manufacturing

NARCIS (Netherlands)

Zijlstra, G.; Groen, M.; Post, J.; Ocelik, V.; de Hosson, J.Th.M.

2016-01-01

This paper concentrates on the effect of the residual stress state during product manufacturing of AISI 420 steel on the final shape of the product. The work includes Finite Element (FE) calculations of the distribution of the residual stresses after metal forming and a heat treatment. The evolution

The earthworm gastrointestinal effect on the release of organic bound residues in soils

Science.gov (United States)

Du, J. H.

2018-03-01

Earthworm activities promote the release of bound residues and the digestive activities of earthworms contribute to the process. Earthworm digestive effects on bound residues can be divided into physical and chemical effects. Physical effects include gastrointestinal abrasion and mixing. The abrasion of soil and litter residues in earthworm gizzards and intestine can grind the food into fine particles, which increase the contact surface with microbial and promote the desorption of bound residues. Chemical effects are attributed to the secreted surfactant substances and digestive enzymes. The surfactants, especially at levels that lead to micellization, can enhance the desorption process of the organic contaminants that sored in the soil. The enzymes in earthworm digestive tracts can decompose the humus in soil, which may promote the release of organic residues that bind with humus.

Effect of washing on pesticide residues in olives.

Science.gov (United States)

Guardia-Rubio, M; Ayora-Cañada, M J; Ruiz-Medina, A

2007-03-01

The present work aims at contributing to the knowledge of the fate of 5 pesticides in olives in order to evaluate how washing may affect the presence of these residues in this fruit (and consequently in olive oil). For this purpose, olives were sprayed with commercial formulations containing the active ingredients and a series of analyses were performed for 64 d by using gas chromatography with mass spectrometric detection. Selected pesticides, ranked by their importance, were diuron, terbuthylazine, simazine, alpha-endosulfan, and beta-endosulfan. The pesticide fraction, which was not removable from olives by washing, increased with time after treatment until their degradation started at week 6. Washing performed 1 d after treatment was the most effective in reducing residues, especially for simazine. Consequently, the washing step performed in olive mills could be effective in removing those herbicide residues present in olives as a consequence of contact with contaminated soil for a short time. This happens when olives are dropped and harvested off the ground by means of brushes or suction equipment.

A survey of residual analysis and a new test of residual trend.

Science.gov (United States)

McDowell, J J; Calvin, Olivia L; Klapes, Bryan

2016-05-01

A survey of residual analysis in behavior-analytic research reveals that existing methods are problematic in one way or another. A new test for residual trends is proposed that avoids the problematic features of the existing methods. It entails fitting cubic polynomials to sets of residuals and comparing their effect sizes to those that would be expected if the sets of residuals were random. To this end, sampling distributions of effect sizes for fits of a cubic polynomial to random data were obtained by generating sets of random standardized residuals of various sizes, n. A cubic polynomial was then fitted to each set of residuals and its effect size was calculated. This yielded a sampling distribution of effect sizes for each n. To test for a residual trend in experimental data, the median effect size of cubic-polynomial fits to sets of experimental residuals can be compared to the median of the corresponding sampling distribution of effect sizes for random residuals using a sign test. An example from the literature, which entailed comparing mathematical and computational models of continuous choice, is used to illustrate the utility of the test. © 2016 Society for the Experimental Analysis of Behavior.

Morphology and composition of pyrotechnic residues formed at different levels of confinement

NARCIS (Netherlands)

Vermeij, E.; Duvalois, W.; Webb, R.; Koeberg, M.

2009-01-01

Post explosion residues (PER) are residues from pyrotechnic compositions or explosives that are generated during an explosion. In the recent past SEM/EDX was used several times to analyze PER from pyrotechnic compositions. The results from these studies suggest that there might be a difference in

Effects of weld residual stresses on crack-opening area analysis of pipes for LBB applications

Energy Technology Data Exchange (ETDEWEB)

Dong, P.; Rahman, S.; Wilkowski, G. [and others

1997-04-01

This paper summarizes four different studies undertaken to evaluate the effects of weld residual stresses on the crack-opening behavior of a circumferential through-wall crack in the center of a girth weld. The effect of weld residual stress on the crack-opening-area and leak-rate analyses of a pipe is not well understood. There are no simple analyses to account for these effects, and, therefore, they are frequently neglected. The four studies involved the following efforts: (1) Full-field thermoplastic finite element residual stress analyses of a crack in the center of a girth weld, (2) A comparison of the crack-opening displacements from a full-field thermoplastic residual stress analysis with a crack-face pressure elastic stress analysis to determine the residual stress effects on the crack-opening displacement, (3) The effects of hydrostatic testing on the residual stresses and the resulting crack-opening displacement, and (4) The effect of residual stresses on crack-opening displacement with different normal operating stresses.

Effects of weld residual stresses on crack-opening area analysis of pipes for LBB applications

International Nuclear Information System (INIS)

Dong, P.; Rahman, S.; Wilkowski, G.

1997-01-01

This paper summarizes four different studies undertaken to evaluate the effects of weld residual stresses on the crack-opening behavior of a circumferential through-wall crack in the center of a girth weld. The effect of weld residual stress on the crack-opening-area and leak-rate analyses of a pipe is not well understood. There are no simple analyses to account for these effects, and, therefore, they are frequently neglected. The four studies involved the following efforts: (1) Full-field thermoplastic finite element residual stress analyses of a crack in the center of a girth weld, (2) A comparison of the crack-opening displacements from a full-field thermoplastic residual stress analysis with a crack-face pressure elastic stress analysis to determine the residual stress effects on the crack-opening displacement, (3) The effects of hydrostatic testing on the residual stresses and the resulting crack-opening displacement, and (4) The effect of residual stresses on crack-opening displacement with different normal operating stresses

Contaminant Release from Residual Waste in Closed Single-Shell Tanks and Other Waste Forms Associated with the Tanks

International Nuclear Information System (INIS)

Deutsch, William J.

2008-01-01

This chapter describes the release of contaminants from the various waste forms that are anticipated to be associated with closure of the single-shell tanks. These waste forms include residual sludge or saltcake that will remain in the tanks after waste retrieval. Other waste forms include engineered glass and cementitious materials as well as contaminated soil impacted by previous tank leaks. This chapter also describes laboratory testing to quantify contaminant release and how the release data are used in performance/risk assessments for the tank waste management units and the onsite waste disposal facilities. The chapter ends with a discussion of the surprises and lessons learned to date from the testing of waste materials and the development of contaminant release models

Potential for thermochemical conversion of biomass residues from the integrated sugar-ethanol process - Fate of ash and ash-forming elements.

Science.gov (United States)

Dirbeba, Meheretu Jaleta; Brink, Anders; DeMartini, Nikolai; Zevenhoven, Maria; Hupa, Mikko

2017-06-01

In this work, potential for thermochemical conversion of biomass residues from an integrated sugar-ethanol process and the fate of ash and ash-forming elements in the process are presented. Ash, ash-forming elements, and energy flows in the process were determined using mass balances and analyses of eight different biomass samples for ash contents, elemental compositions, and heating values. The results show that the ash content increases from the sugarcane to the final residue, vinasse. The cane straw, which is left in the field, contains one-third of the energy and 25% of the K and Cl while the vinasse contains 2% of the energy and 40% of the K and Cl in the cane. K and Cl in biomass fuels cause corrosion and fouling problems in boilers and gasifiers. Over 85% of these elements in the straw are water soluble indicating that water leaching would improve it for utilization in thermochemical conversion. Copyright © 2017 Elsevier Ltd. All rights reserved.

Effect of commercial processing procedures on 14C-LINDANE residues in corn oil

International Nuclear Information System (INIS)

Soliman, S.M.

2006-01-01

At blooming, maize plants were sprayed twice, 23 days apart, at a dose of 22 mg equivalent to 5 μCi/ plant. At post harvest, maize seeds had a radioactivity corresponding to 0.36% of the applied dose. The insecticide residues in crude oil, cake and methanolic extract were amounted to 8 % and 60 % 5 % , respectively, of original residues inside the seeds.The 14 C-activity in the crude oil could be reduced by commercial processes locally used for refining. The refined oil had a residue level of about 0.7 ppm mainly in the form of unchanged lindane in addition to a number of chloro phenols as main metabolites. Refining of corn oil fortified with 14 C-lindane led to a high reduction of 14 C-lindane (88%). The refined oil contained a residue consisting lindane and its chloro phenols

Stress-Softening and Residual Strain Effects in Suture Materials

Directory of Open Access Journals (Sweden)

Alex Elías-Zúñiga

2013-01-01

Full Text Available This work focuses on the experimental characterization of suture material samples of MonoPlus, Monosyn, polyglycolic acid, polydioxanone 2–0, polydioxanone 4–0, poly(glycolide-co-epsilon-caprolactone, nylon, and polypropylene when subjected to cyclic loading and unloading conditions. It is found that all tested suture materials exhibit stress-softening and residual strain effects related to the microstructural material damage upon deformation from the natural, undistorted state of the virgin suture material. To predict experimental observations, a new constitutive material model that takes into account stress-softening and residual strain effects is developed. The basis of this model is the inclusion of a phenomenological nonmonotonous softening function that depends on the strain intensity between loading and unloading cycles. The theory is illustrated by modifying the non-Gaussian average-stretch, full-network model to capture stress-softening and residual strains by using pseudoelasticity concepts. It is shown that results obtained from theoretical simulations compare well with suture material experimental data.

Universal relationship connecting various two-body effective residual interactions

International Nuclear Information System (INIS)

Knuepfer, W.; Huber, M.G.

1976-01-01

Starting from a momentum space analysis of the two-body matrix elements, a relation has been established between the size of the model space actually used in a specific calculation and the relevant properties of the effective residual interaction. It turns out that the two-body transition density acts like a filter function on the Fourier transform of the force; it exhibits a distinct structure which clearly reflects the size and the detailed properties of the configuration space actually used. From an investigation of this filter function an equivalence criterion for different effective residual two-body interactions has been established both for closed and open shell nuclei. This result can be used to construct simple although realistic effective forces. As an example, a model for a separable residual interaction is proposed in which the corresponding parameters are being clearly related to the nuclear radius (i.e., the mass number), to the quantum numbers (i.e., the angular momentum) of the state under consideration and to the size of the configuration space used. For a number of examples this force has been applied successfully for the description of low energy properties of both closed and open shell nuclei

Mapping of Residues Forming the Voltage Sensor of the Voltage-Dependent Anion-Selective Channel

Science.gov (United States)

Thomas, Lorie; Blachly-Dyson, Elizabeth; Colombini, Marco; Forte, Michael

1993-06-01

Voltage-gated ion-channel proteins contain "voltage-sensing" domains that drive the conformational transitions between open and closed states in response to changes in transmembrane voltage. We have used site-directed mutagenesis to identify residues affecting the voltage sensitivity of a mitochondrial channel, the voltage-dependent anion-selective channel (VDAC). Although charge changes at many sites had no effect, at other sites substitutions that increased positive charge also increased the steepness of voltage dependance and substitutions that decreased positive charge decreased voltage dependance by an appropriate amount. In contrast to the plasma membrane K^+ and Na^+ channels, these residues are distributed over large parts of the VDAC protein. These results have been used to define the conformational transitions that accompany voltage gating of an ion channel. This gating mechanism requires the movement of large portions of the VDAC protein through the membrane.

The Effect of Processing on 14C- Chlofenvinphos Residues in Maize Oil and Bioavailability of its Cake Residues on Rats

International Nuclear Information System (INIS)

Mahdy, F.; El-Maghraby, S.

2008-01-01

Maize seed obtained from 14 C-chlofenvinphos treated plants contained 0.12 % of the applied dose. The insecticide residues in crude oil, methanol and coke amounted to 10 %, 6 % and 69 %, respectively of original residues inside the seeds.The 14 C activity in the crude oil could be a gradual reduced by the refining processes. The alkali treatment and bleaching steps are more effective steps in the refining processes remove about (63 %). The refined oil contained only about 17 % of the 14 C-residues originally present. The major residues in processed oil contain parent compound, in addition to five metabolites of the insecticide. When rats fed the extracted seeds (cake), the bound residues were found to be considerably bioavailable. After feeding rats for 5 days with the cake, a substantial amount of 14 C-residues was eliminated in the urine (59.5 %), while about 20 % was excreted in the feces. About 15 % of the radioactivity was distribution among various organs

EFFECT OF SOIL TILLAGE AND PLANT RESIDUE ON SURFACE ROUGHNESS OF AN OXISOL UNDER SIMULATED RAIN

Directory of Open Access Journals (Sweden)

Elói Panachuki

2015-02-01

Full Text Available Surface roughness of the soil is formed by mechanical tillage and is also influenced by the kind and amount of plant residue, among other factors. Its persistence over time mainly depends on the fundamental characteristics of rain and soil type. However, few studies have been developed to evaluate these factors in Latossolos (Oxisols. In this study, we evaluated the effect of soil tillage and of amounts of plant residue on surface roughness of an Oxisol under simulated rain. Treatments consisted of the combination of the tillage systems of no-tillage (NT, conventional tillage (CT, and minimum tillage (MT with rates of plant residue of 0, 1, and 2 Mg ha-1 of oats (Avena strigosa Schreb and 0, 3, and 6 Mg ha-1 of maize (Zea mays L.. Seven simulated rains were applied on each experimental plot, with intensity of 60±2 mm h-1 and duration of 1 h at weekly intervals. The values of the random roughness index ranged from 2.94 to 17.71 mm in oats, and from 5.91 to 20.37 mm in maize, showing that CT and MT are effective in increasing soil surface roughness. It was seen that soil tillage operations carried out with the chisel plow and the leveling disk harrow are more effective in increasing soil roughness than those carried out with the heavy disk harrow and leveling disk harrow. The roughness index of the soil surface decreases exponentially with the increase in the rainfall volume applied under conditions of no tillage without soil cover, conventional tillage, and minimum tillage. The oat and maize crop residue present on the soil surface is effective in maintaining the roughness of the soil surface under no-tillage.

Chemical activation of gasification carbon residue for phosphate removal

Science.gov (United States)

Kilpimaa, Sari; Runtti, Hanna; Lassi, Ulla; Kuokkanen, Toivo

2012-05-01

Recycling of waste materials provides an economical and environmentally significant method to reduce the amount of waste. Bioash formed in the gasification process possesses a notable amount of unburned carbon and therefore it can be called a carbon residue. After chemical activation carbon residue could be use to replace activated carbon for example in wastewater purification processes. The effect of chemical activation process variables such as chemical agents and contact time in the chemical activation process were investigated. This study also explored the effectiveness of the chemically activated carbon residue for the removal of phosphate from an aqueous solution. The experimental adsorption study was performed in a batch reactor and the influence of adsorption time, initial phosphate concentration and pH was studied. Due to the carbon residue's low cost and high adsorption capacity, this type of waste has the potential to be utilised for the cost-effective removal of phosphate from wastewaters. Potential adsorbents could be prepared from these carbonaceous by-products and used as an adsorbent for phosphate removal.

Effects of fluoride residue on thermal stability in Cu/porous low-k interconnects

Energy Technology Data Exchange (ETDEWEB)

Kobayashi, Y.; Ozaki, S.; Nakamura, T. [FUJITSU LABORATORIES Ltd., 10-1 Morinosato-Wakamiya, Atsugi, Kanagawa 243-0197 (Japan)

2014-06-19

We have investigated the effects of fluoride residue on the thermal stability of a Cu/barrier metal (BM)/porous low-k film (k < 2.3) structure. We confirmed that the Cu agglomerated more on a BM/inter layer dielectric (ILD) with a fluoride residue. To consider the effect of fluoride residue on Cu agglomeration, the structural state at the Cu/BM interface was evaluated with a cross-section transmission electron microscope (TEM) and atomic force microscope (AFM). In addition, the chemical bonding state at the Cu/BM interface was evaluated with the interface peeling-off method and X-ray photoelectron spectroscopy (XPS). Moreover, we confirmed the ionization of fluoride residue and oxidation of Cu with fluoride and moisture to clarify the effect of fluoride residue on Cu. Our experimental results indicated that the thermal stability in Cu/porous low-k interconnects was degraded by enhancement of Cu oxidation with fluoride ions diffusion as an oxidizing catalyst.

Recycling of porcelain tile polishing residue in portland cement: hydration efficiency.

Science.gov (United States)

Pelisser, Fernando; Steiner, Luiz Renato; Bernardin, Adriano Michael

2012-02-21

Ceramic tiles are widely used by the construction industry, and the manufacturing process of ceramic tiles generates as a major residue mud derived from the polishing step. This residue is too impure to be reused in the ceramic process and is usually discarded as waste in landfills. But the analysis of the particle size and concentration of silica of this residue shows a potential use in the manufacture of building materials based on portland cement. Tests were conducted on cement pastes and mortars using the addition of 10% and 20% (mass) of the residue. The results of compressive strength in mortars made up to 56 days showed a significant increase in compressive strength greater than 50%. The result of thermogravimetry shows that portlandite is consumed by the cement formed by the silica present in the residue in order to form calcium silicate hydrate and featuring a pozzolanic reaction. This effect improves the performance of cement, contributes to research and application of supplementary cementitious materials, and optimizes the use of portland cement, reducing the environmental impacts of carbon dioxide emissions from its production.

Efficacy of citric acid denture cleanser on the Candida albicans biofilm formed on poly(methyl methacrylate): effects on residual biofilm and recolonization process.

Science.gov (United States)

Faot, Fernanda; Cavalcanti, Yuri Wanderley; Mendonça e Bertolini, Martinna de; Pinto, Luciana de Rezende; da Silva, Wander José; Cury, Altair Antoninha Del Bel

2014-06-23

It is well known that the use of denture cleansers can reduce Candida albicans biofilm accumulation; however, the efficacy of citric acid denture cleansers is uncertain. In addition, the long-term efficacy of this denture cleanser is not well established, and their effect on residual biofilms is unknown. This in vitro study evaluated the efficacy of citric acid denture cleanser treatment on C. albicans biofilm recolonization on poly(methyl methacrylate) (PMMA) surface. C. albicans biofilms were developed for 72 h on PMMA resin specimens (n = 168), which were randomly assigned to 1 of 3 cleansing treatments (CTs) overnight (8 h). CTs included purified water as a control (CTC) and two experimental groups that used either a 1:5 dilution of citric acid denture cleanser (CT5) or a 1:8 dilution of citric acid denture cleanser (CT8). Residual biofilms adhering to the specimens were collected and quantified at two time points: immediately after CTs (ICT) and after cleaning and residual biofilm recolonization (RT). Residual biofilms were analyzed by quantifying the viable cells (CFU/mL), and biofilm architecture was evaluated by confocal laser scanning microscopy (CLSM) and scanning electron microscopy (SEM). Denture cleanser treatments and evaluation periods were considered study factors. Data were analyzed using two-way ANOVA and Tukey's Honestly Significant Difference (HSD) test (α = 0.05). Immediately after treatments, citric acid denture cleansing solutions (CT5 and CT8) reduced the number of viable cells as compared with the control (p recolonization (p recolonization was also detected by CLSM and SEM analysis, which revealed a higher biomass and average biofilm thickness for the CT8 group (p recolonization.

Effects of residual stress on irradiation hardening in stainless steels

Energy Technology Data Exchange (ETDEWEB)

Okubo, N.; Kondo, K.; Kaji, Y. [Japan Atomic Energy Agency, Tokai-mura, Naga-gun, Ibaraki-ken (Japan); Miwa, Y. [Nuclear Energy and Science Directorate, Japan Atomic Energy Agency, Tokai-mura, Ibaraki-ken (Japan)

2007-07-01

Full text of publication follows: Structural materials in fusion reactor with water cooling system will undergo corrosion in aqueous environment and heavier irradiation than that in LWR. Irradiation assisted stress corrosion (IASCC) may be induced in stainless steels exposed in these environment for a long term of reactor operation. The IASCC is considered to be caused in a welding zone. It is difficult to predict and estimate the IASCC, because several irradiation effects (irradiation hardening, swelling, irradiation induced stress relaxation, etc) work intricately. Firstly, effects of residual stress on irradiation hardening were investigated in stainless steels. Specimens used in this study were SUS316 and SUS316L. By bending deformation, the specimens with several % plastic strain, which corresponds to weld residual stress, were prepared. Ion irradiations of 12 MeV Ni{sup 3+} were performed at 330, 400 and 550 deg. C to 45 dpa in TIARA facility at JAEA. No bent specimen was simultaneously irradiated with the bent specimen. The residual stress was estimated by X-ray residual stress measurements before and after the irradiation. The micro-hardness was measured by using nano-indenter. The irradiation hardening and the stress relaxation were changed by irradiation under bending deformation. The residual stress did not relax even for the case of the higher temperature aging at 500 deg. C for the same time of irradiation. The residual stress after ion irradiation, however, relaxed at these experimental temperatures in SUS316L. The hardness was obviously suppressed in bent SUS316L irradiated at 300 deg. C to 6 or 12 dpa. It was evident that irradiation induced stress relaxation occasionally suppressed the irradiation hardening in SUS316L. (authors)

Effects of plantation residue management on the community ...

African Journals Online (AJOL)

Effects of plantation residue management on the community structure of wattle regeneration invertebrate pests in South Africa. ... Members of the soil invertebrate pest complex included whitegrubs and cutworms that generally had a higher pest status than millipedes, nematodes, grasshoppers, ants, false wireworms, ...

Effect of residual stress induced by cold expansion on fatigue crack ...

African Journals Online (AJOL)

Fatigue life and fatigue crack growth rate are controlled by stress ratio, stress level, orientation of crack, temper-ature, residual stress, corrosion, etc. The effects of residual stress on fatigue crack growth in aluminium (Al) alloy 2024-T351 by Mode I crack were investigated by applying constant amplitude cycles based on ...

Expanded heat treatment to form residual compressive hoop stress on inner surface of zirconium alloy tubing

International Nuclear Information System (INIS)

Megata, Masao

1997-01-01

A specific heat treatment process that introduces hoop stress has been developed. This technique can produce zirconium alloy tubing with a residual compressive hoop stress near the inner surface by taking advantage of the mechanical anisotropy in hexagonal close-packed zirconium crystal. Since a crystal having its basal pole parallel to the tangential direction of the tubing is easier to exhibit plastic elongation under the hoop stress than that having its basal pole parallel to the radial direction, the plastic and elastic elongation can coexist under a certain set of temperature and hoop stress conditions. The mechanical anisotropy plays a role to extend the coexistent stress range. Thus, residual compressive hoop stress is formed at the inner surface where more plastic elongation occurs during the heat treatment. This process is referred to as expanded heat treatment. Since this is a fundamental crystallographic principle, it has various applications. The application to improve PCI/SCC (pellet cladding interaction/stress corrosion cracking) properties of water reactor fuel cladding is promising. Excellent results were obtained with laboratory-scale heat treatment and an out-reactor iodine SCC test. These results included an extension of the time to SCC failure. (author)

Effect of processing on residues of chlorpyrifos in stored corn and rice

International Nuclear Information System (INIS)

Tejada, A.W.; Calumpang, S.M.F.; Gambalan, N.B.

1990-01-01

The effect of processing on residues of chlorpyrifos in rice and corn was determined. Chlorpyrifos solution (0.1%) sprayed on jute sacks containing corn resulted in absorption of residues in kernel and cob up to six months. A similar trend was observed in rice. Radiotracer studies revealed very low levels of bound residues (0.2 - 0.8 mg/kg) present in rice only. The usual practice of washing rice and corn before cooking reduced chlorpyrifos residues as much as 57% to 100%. Residues in wash water declined with each washing. Cooking further reduced the residues of chlorpyrifos only when volatilization was possible. Chlorpyrifos appeared to be persistent. Cooking rice in plot with the lid on did not produce any substantial reduction in the chlorpyrifos content. The practice of storing rice and corn in the Philippines does not give rice to chlorpyrifos residues which may exceed the recommended daily intake of 0.01 mg/kg-bw. (Auth.) 13 refs., 12 tabs., 3 figs

6-Iso-chlortetracycline or keto form of chlortetracycline? Need for clarification for relevant monitoring of chlortetracycline residues in food.

Science.gov (United States)

Gaugain, Murielle; Gautier, Sophie; Bourcier, Sophie; Jacques, Anne-Marie; Laurentie, Michel; Abjean, Jean-Pierre; Hurtaud-Pessel, Dominique; Verdon, Eric

2015-01-01

Chlortetracycline (CTC) is a broad-spectrum antibiotic used in veterinary medicine for pulmonary or digestive infections and having a regulatory maximum residue limit (MRL) necessitating an official analytical control method. The purpose of this study was to clarify the identification of different forms of CTC observed in standard solution, in spiked muscle samples and in naturally incurred muscle samples of pigs analysed by LC-MS/MS and to demonstrate the in vivo formation of 6-iso-chlortetracycline and 4-epi-6-iso-CTC as a metabolite of CTC and 4-epi-CTC in muscle. The six following forms were identified, all being isobaric with a protonated molecule at m/z 479 (precursor ion): the keto-enol forms of CTC and the keto-enol forms of 4-epi-chlortetracycline (4-epi-CTC), 6-iso-chlortetracycline (6-iso-CTC) and 4-epi-6-iso-chlortetracycline (4-epi-6-iso-CTC). The 6-iso-CTC and 4-epi-6-iso-CTC were observed only in incurred pig samples so were identified for the first time as metabolites of CTC and 4-epi-CTC. Identification of the different forms was obtained by comparing incurred muscle samples with standard solutions and with spiked samples. Then the differences between the features of the chromatograms obtained by LC-TQ-MS and the fragmentation study of the different forms of CTC obtained by LC-Q-TOF-MS helped us to support this identification. The extraction steps and the LC-MS/MS conditions developed to analyse muscle tissue samples are described. This clarification concerning the rigorous identification of chromatographic peaks allowed us to evaluate the relevance of our monitoring method with regard to the regulations in place in the European Union and could be of help to laboratories involved in official control of antibiotic residues in food of animal origin. Additional results are also presented highlighting the transformation of the CTC when prepared in a mixture with other antibiotics.

Norepinephrine transporter function and desipramine: residual drug effects versus short-term regulation.

Science.gov (United States)

Ordway, Gregory A; Jia, Weihong; Li, Jing; Zhu, Meng-Yang; Mandela, Prashant; Pan, Jun

2005-04-30

Previous research has shown that exposure of norepinephrine transporter (NET)-expressing cells to desipramine (DMI) downregulates the norepinephrine transporter, although changes in the several transporter parameters do not demonstrate the same time course. Exposures to desipramine for effects of residual desipramine on norepinephrine transporter binding and uptake were re-evaluated following exposures of PC12 cells to desipramine using different methods to remove residual drug. Using a method that minimizes residual drug, exposure of intact PC12 cells to desipramine for 4h had no effect on uptake capacity or [(3)H]nisoxetine binding to the norepinephrine transporter, while exposures for > or =16 h reduced uptake capacity. Desipramine-induced reductions in binding to the transporter required >24 h or greater periods of desipramine exposure. This study confirms that uptake capacity of the norepinephrine transporter is reduced earlier than changes in radioligand binding, but with a different time course than originally shown. Special pre-incubation procedures are required to abolish effects of residual transporter inhibitor when studying inhibitor-induced transporter regulation.

Roles of the β 146 histidyl residue in the molecular basis of the Bohr Effect of hemoglobin: A proton nuclear magnetic resonance study

International Nuclear Information System (INIS)

Busch, M.R.; Mace, J.E.; Ho, N.T.; Ho, Chien

1991-01-01

Assessment of the roles of the carboxyl-terminal β146 histidyl residues in the alkaline Bohr effect in human and normal adult hemoglobin by high-resolution proton nuclear magnetic resonance spectroscopy requires assignment of the resonances corresponding to these residues. By a careful spectroscopic study of human normal adult hemoglobin, enzymatically prepared des(His146β)-hemoglobin, and the mutant hemoglobins Cowtown (β146His → Leu) and York (β146His → Pro), the authors have resolved some of these conflicting results. By a close incremental variation of pH over a wide range in chloride-free 0.1 M N-(2-hydroxyethyl)piperazine-N'-2-ethanesulfonic acid buffer, a single resonance has been found to be consistently missing in the proton nuclear magnetic resonance spectra of these hemoglobin variants. The results indicate that the contribution of the β146 histidyl residues is 0.52 H + /hemoglobin tetramer at pH 7.6, markedly less than 0.8 H + /hemoglobin tetramer estimated by study of the mutant hemoglobin Cowtown (β146His → Leu) by Shih and Perutz. They have found that at least two histidyl residues in the carbonmonoxy form of this mutant have pK values that are perturbed, and they suggest that these pK differences may in part account for this discrepancy. The results show that the pK values of β146 histidyl residues in the carbonmonoxy form of hemoglobin are substantially affected by the presence of chloride and other anions in the solvent, and thus, the contribution of this amino acid residue to the alkaline Bohr effect can be shown to vary widely in magnitude, depending on the solvent composition. These results demonstrate that the detailed molecular mechanisms of the alkaline Bohr effect are not unique but are affected both by the hemoglobin structure and by the interactions with the solvent components in which the hemoglobin molecule resides

The effect of radiation on the function of the residual pancreas

International Nuclear Information System (INIS)

Matsuoka, Yoshisuke; Tsujii, Hirohiko; Kamada, Tadashi; Irie, Goro

1987-01-01

For patients with carcinomas of the bile duct and the pancreas, a pancreatoduodenectomy is generally the first choise of treatment. In our institute, the residual pancreas after surgery is transplanted into the abdominal wall in order to prevent diabetes mellites. We irradiated the residual pancreas postoperatively with a dosage of 15 to 43 Gy in order to inhibit the exocrine function. We then removed the drainage catheter from the residual pancreas. In the treatment, the endocrine function can be preserved. With respect to the radiation effect on the exocrine function, the amount of pancreatic secretion showed a transient increase in the first few days after the start of the irradiation, followed by a mild decrease. The serum amylase decreased immediatelly after the start of irradiation and increased sequentially during long-term observations. The amylase in the pancreatic juice showed a remarkable decrease immediatelly after the start of irradiation, and this decrease was maintained during long-term observations (The minimum level was observed from the dosage of 20 to 30 Gy). In order to analyse the radiation effect on the endocrine function, 50 g OGTTs were performed before and after irradiation in thirteen patients. In two of the thirteen patients, the results of the tests showed a new diabetic pattern after irradiation, which required insulin in one patient. It was concluded from our study that irradiation to the residual pancreas with in the dosage of 15 to 43 Gy the catheters in the residual pancreas could be removed in fourteen of fifteen patients without any unfavorable effect. (author)

Effect of Filament Fineness on Composite Yarn Residual Torque

Directory of Open Access Journals (Sweden)

Sarıoğlu Esin

2018-03-01

Full Text Available Yarn residual torque or twist liveliness occurs when the twist is imparted to spin the fibers during yarn formation. It causes yarn snarling, which is an undesirable property and can lead the problems for further processes such as weaving and knitting. It affects the spirality of knitted fabrics and skewness of woven fabrics. Generally, yarn residual torque depends on yarn twist, yarn linear density, and fiber properties used. Composite yarns are widely produced to exploit two yarns with different properties such on optimum way at the same time and these yarns can be produced by wrapping sheath fibers around filament core fiber with a certain twist. In this study, the effect of filament fineness used as core component of composite yarn on residual torque was analyzed. Thus, the false twist textured polyester filament yarns with different filament fineness were used to produce composite yarns with different yarn count. The variance analysis was performed to determine the significance of twist liveliness of filament yarns and yarn count on yarn twist liveliness. Results showed that there is a statistically significant differences at significance level of α=0.05 between filament fineness and yarn residual torque of composite yarns.

Mapping and quantification of organic agro-industrial residues in East Africa

Energy Technology Data Exchange (ETDEWEB)

Jungersen, G. [Dansk Teknologisk Inst. (Denmark); Kivaisi, A.; Rubindamayugi, M. [Univ. of Dar es Salaam (Tanzania, United Republic of)

1998-05-01

The East-African agro-industries generate very large quantities of organic residues from production and processing of different crops. These residues form a major contribution to the pollution of air, soil and water ways, but, at the same time they constitute a large potential for production of bioenergy through anaerobic digestion as well as potential substrate for other biological fermentation processes. The utilization of these resources for production of valuable products would contribute significantly to: Improvement of the local energy supply, through production of bio-energy; Improvement of the economy of the East African agro-industry; Reduction of the environmental impact from the agro-industrial sector. Except for production of cane sugar, most agro-industrial residues are generated from cash crops, which are produced and processed in the developing countries and where the final products mainly are used for export. In the East-African Region the most important of these crops are: Sisal, coffee, Cashew nuts and Pineapple. In addition significant quantities of organic residues are generated from other food processing activities like breweries, consumption of bananas etc. The total potential methane production of the residues available for use in biomethanization systems in East Africa is 189.61 million m{sup 3} of methane per year. Converted to diesel oil equivalents and including the residues only feasible for combustion systems, the total bioenergy potential of agro-industrial residues in Eastern Africa is 279,176 TOE. If this potential was fully utilized for production of electricity, it would correspond to installed effects of 37,68 and 31 MW in Tanzania, Kenya and Uganda, respectively, equivalent to 10%, 11% and 18% of the currently installed effect is these countries. Residues from sisal and coffee processing constitute the main part of the bioenergy potential, on average approximately 75%, while the remaining 25% of the potential are formed by the

Effectiveness of Commercial and Homemade Washing Agents in Removing Pesticide Residues on and in Apples.

Science.gov (United States)

Yang, Tianxi; Doherty, Jeffery; Zhao, Bin; Kinchla, Amanda J; Clark, John M; He, Lili

2017-11-08

Removal of pesticide residues from fresh produce is important to reduce pesticide exposure to humans. This study investigated the effectiveness of commercial and homemade washing agents in the removal of surface and internalized pesticide residues from apples. Surface-enhanced Raman scattering (SERS) mapping and liquid chromatography tandem mass spectrometry (LC-MS/MS) methods were used to determine the effectiveness of different washing agents in removing pesticide residues. Surface pesticide residues were most effectively removed by sodium bicarbonate (baking soda, NaHCO 3 ) solution when compared to either tap water or Clorox bleach. Using a 10 mg/mL NaHCO 3 washing solution, it took 12 and 15 min to completely remove thiabendazole or phosmet surface residues, respectively, following a 24 h exposure to these pesticides, which were applied at a concentration of 125 ng/cm 2 . LC-MS/MS results showed, however, that 20% of applied thiabendazole and 4.4% of applied phosmet had penetrated into the apples following the 24 h exposure. Thiabendazole, a systemic pesticide, penetrated 4-fold deeper into the apple peel than did phosmet, a non-systemic pesticide, which led to more thiabendazole residues inside the apples, which could not be washed away using the NaHCO 3 washing solution. This study gives us the information that the standard postharvest washing method using Clorox bleach solution for 2 min is not an effective means to completely remove pesticide residues on the surface of apples. The NaHCO 3 method is more effective in removing surface pesticide residues on apples. In the presence of NaHCO 3 , thiabendazole and phosmet can degrade, which assists the physical removal force of washing. However, the NaHCO 3 method was not completely effective in removing residues that have penetrated into the apple peel. The overall effectiveness of the method to remove all pesticide residues diminished as pesticides penetrated deeper into the fruit. In practical application

Radiation effects in glass waste forms for high-level waste and plutonium disposal

International Nuclear Information System (INIS)

Weber, W.J.; Ewing, R.C.

1997-01-01

A key challenge in the permanent disposal of high-level waste (HLW), plutonium residues/scraps, and excess weapons plutonium in glass waste forms is the development of predictive models of long-term performance that are based on a sound scientific understanding of relevant phenomena. Radiation effects from β-decay and α-decay can impact the performance of glasses for HLW and Pu disposition through the interactions of the α-particles, β-particles, recoil nuclei, and γ-rays with the atoms in the glass. Recently, a scientific panel convened under the auspices of the DOE Council on Materials Science to assess the current state of understanding, identify important scientific issues, and recommend directions for research in the area of radiation effects in glasses for HLW and Pu disposition. The overall finding of the panel was that there is a critical lack of systematic understanding on radiation effects in glasses at the atomic, microscopic, and macroscopic levels. The current state of understanding on radiation effects in glass waste forms and critical scientific issues are presented

The effect of sludge water treatment plant residuals on the properties of compressed brick

Science.gov (United States)

Shamsudin, Shamrul-Mar; Shahidan, S.; Azmi, M. A. M.; Ghaffar, S. A.; Ghani, M. B. Abdul; Saiful Bahari, N. A. A.; Zuki, S. S. M.

2017-11-01

The focus of this study is on the production of compressed bricks which contains sludge water treatment plant (SWTP) residuals obtained from SAJ. The main objective of this study is to utilise and incorporate discarded material (SWTP) in the form of residual solution to produce compressed bricks. This serves as one of the recycling efforts to conserve the environment. This study determined the optimum mix based on a mix ratio of 1:2:4 (cement: sand: soil) in the production of compressed bricks where 5 different mixes were investigated i. e. 0%, 5%, 10%, 20%, and 30% of water treatment plant residue solution. The production of the compressed bricks is in accordance with the Malaysian Standard MS 7.6: 1972 and British Standard BS 3921: 1985 - Compressive Strength & Water Absorption. After being moulded and air dried, the cured bricks were subjected to compression tests and water absorption tests. Based on the tests conducted, it was found that 20% of water treatment plant residue solution which is equivalent to 50% of soil content replacement with a mix composition of [10: cement] [20: sand] [20: soil] [20: water treatment plant residue solution] is the optimum mix. It was also observed that the bricks containing SWTP residuals were lighter in weight compared to the control specimens

Effects of iron-aluminium oxides and organic carbon on aggregate stability of bauxite residues.

Science.gov (United States)

Zhu, Feng; Li, Yubing; Xue, Shengguo; Hartley, William; Wu, Hao

2016-05-01

In order to successfully establish vegetation on bauxite residue, properties such as aggregate structure and stability require improvement. Spontaneous plant colonization on the deposits in Central China over the last 20 years has revealed that natural processes may improve the physical condition of bauxite residues. Samples from three different stacking ages were selected to determine aggregate formation and stability and its relationship with iron-aluminium oxides and organic carbon. The residue aggregate particles became coarser in both dry and wet sieving processes. The mean weight diameter (MWD) and geometry mean diameter (GMD) increased significantly, and the proportion of aggregate destruction (PAD) decreased. Natural stacking processes could increase aggregate stability and erosion resistant of bauxite residues. Free iron oxides and amorphous aluminium oxides were the major forms in bauxite residues, but there was no significant correlation between the iron-aluminium oxides and aggregate stability. Aromatic-C, alkanes-C, aliphatic-C and alkenes-C were the major functional groups present in the residues. With increasing stacking age, total organic carbon content and aggregate-associated organic carbon both increased. Alkanes-C, aliphatic-C and alkenes-C increased and were mainly distributed in macro-aggregates, whereas aromatic-C was mainly distributed in aluminium oxides maybe more important for stability of micro-aggregates.

How effective are common household preparations on removing pesticide residues from fruit and vegetables? A review.

Science.gov (United States)

Chung, Stephen Wc

2018-06-01

Nowadays, the use of pesticides is inevitable for pest control in crops, especially for fruit and vegetables. After the harvest from raw agricultural commodities, the amount of pesticide residues in food is mainly influenced by the storage, handling and processing that follow. If good agricultural and good manufacturing practices are enforced effectively, the amount of pesticide residues would be brought below the corresponding maximum residue level. Thus, the consumption of raw and/or prepared fruit and vegetables would be safe. Nonetheless, reports regarding pesticide residues in fruit or vegetables on mass media have been worrying consumers, who are concerned about the adverse effects of pesticide residues. As a result, consumers perform household processing before consumption to reduce any related risks. However, can these preparations effectively remove pesticide residues? Reviewing the extensive literature, it showed that, in most cases, washing and soaking can only lead to a certain degree of reduction in residue level, while other processing such as peeling, soaking in chemical baths and blanching can reduce pesticide residues more effectively. In general, the behaviour of residues during processing can be rationalised in terms of the physico-chemical properties of the pesticide and the nature of the process. In contrast, the reported studies are diversified and some areas still lack sufficient studies to draw any remarks. Recommendations are provided with respect to the available information that aims to formulate an environmental friendly, cost-effective and efficient household processing of fruit and vegetables to reduce pesticide residues. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Effects of cooking and storage on residues of cyadox in chicken muscle.

Science.gov (United States)

Zhang, Yanling; Wang, Yulian; Huang, Lingli; Chen, Dongmei; Tao, Yanfei; Yuan, Zonghui

2005-12-14

The aim of this study was to investigate the depletion of residues of cyadox in chicken muscle over time. The heat stabilities of cyadox (CYX) and its two metabolites, 1,4-bisdesoxycyadox (BDCYX) and quinoxaline-2-carboxylic acid (QCA), in water, cooking oil, and as incurred residues in chicken muscle were investigated. CYX was shown to be unstable with a half-life of about 37.7 min in 100 degrees C water. In hot cooking oil at 180 degrees C, all three compounds were unstable. CYX decreased quickly and was not able to be detected after heating for 2 min. Diode-array analysis of CYX standard solution in cooking oil indicated that a portion of BDCYX was formed. The residues of CYX and BDCYX deteriorated rapidly in frozen storage, while that of QCA changed slowly. Muscles containing CYX residues were boiled, microwaved, or fried for the specified times. During boiling, CYX and BDCYX were reduced 94% and 81% in 10 min, respectively. During microwave cooking, CYX and BDCYX were reduced 54% and 47% in 2.5 min, respectively. During frying, CYX and BDCYX were reduced 86% and 76%, respectively. No significant reduction of QCA was found for the three cooking methods. The half-lives of CYX residues in cooked chicken muscles were estimated as follows: 2.22 min for CYX and 4.44 min for BDCYX by boiling; 6.66 min for CYX and 9.36 min for BDCYX by microwaving.

A hierarchical structure through imprinting of a polyimide precursor without residual layers

International Nuclear Information System (INIS)

Pai, I-Ting; Hon, Min-Hsiung; Leu, Ing-Chi

2008-01-01

A patterned polyimide without a residual layer is obtained by imprinting with the assistance of a residual solvent. The effects of the wetting behaviors of the poly-amic acid (PAA) solution coated on various surfaces are examined and the formation of hierarchical patterns without residual layers is demonstrated. polydimethylsiloxane (PDMS) and PEI/PDMS are used as imprinting molds with Si and 300 nm SiO 2 /Si as substrates. The results indicate that the various ambits of patterns without a residual layer are formed due to the dewetting phenomena caused by surface tension (Suh 2006 Small 2 832). During imprinting, PDMS with a low surface energy makes the PAA solution flow away from its surface exposing the contact area due to dewetting. Self-organized hierarchical structures are also obtained from this process due to effective dewetting. The present study provides a new approach for fabricating patterns without residual layers and the consequent preparation of hierarchical structures, which is considered to be impossible using the lithographic technique

The effect of delignification process with alkaline peroxide on lactic acid production from furfural residues

Directory of Open Access Journals (Sweden)

Yong Tang

2012-11-01

Full Text Available Furfural residues produced from the furfural industry were investigated as a substrate for lactic acid production by simultaneous saccharification and fermentation (SSF. Alkaline peroxide was used for delignification of furfural residues to improve the final lactic acid concentration. The residue was treated with 1.3% to 1.7% hydrogen peroxide at 80 °C for 1 h with a substrate concentration of 3.33%. SSF of furfural residues with different delignification degrees were carried out to evaluate the effect of delignification degree on lactic acid production. Using corn hydrolysates/ furfural residues as substrates, SSF with different media were carried out to investigate the effect of lignin on the interaction between enzymes and lactic acid bacteria. Lactic acid bacteria had a negative effect on cellulase, thus resulting in the reduction of enzyme activity. Lignin and nutrients slowed down the decreasing trend of enzyme activity. A higher delignification resulted in a slower fermentation rate and lower yield due to degradation products of lignin and the effect of lignin on the interaction between enzymes and lactic acid bacteria. For the purpose of lactic acid production, a moderate delignification (furfural residues with the lignin content of 14.8% was optimum.

The Effect of Crop Residue Application to Soil Fauna Community and Mungbean Growth (Vigna radata

Directory of Open Access Journals (Sweden)

SUGIYARTO

2000-01-01

Full Text Available Litterbag experiment was carried out to determine the effect of crop residue application to soil fauna community and mungbean growth. The experiment arranged in randomized complete design with triplicate. The four treatment application of crotalarian, rice straw and banana’s aerial stem residues as well as without residue application as control. Soil fauna community and mungbean growth measured at 8 weeks after mungbean sown. Soil fauna extracted by modified Barless-Tullgren extractor apparatus. Height and dry weight of mungbean measured as crop growth parameters. The results indicated that the soil fauna densities and diversities as well as the growth of mungbean tended to increase by the application of crop residues. The effect of the treatment decreasing in the following order: banana’s aerial stem residue > crotalarian residue > rice straw > without residue application. There were high correlation between mungbean growth and soil fauna diversities.© 2001 Jurusan Biologi FMIPA UNS SurakartaKey words:

Toxic effects of ethylene oxide residues on bovine embryos in vitro.

Science.gov (United States)

Holyoak, G R; Wang, S; Liu, Y; Bunch, T D

1996-04-15

The potential of ethylene oxide (EtO) residues in exposed plastic tissue culture dishes to adversely affect bovine oocyte maturation, fertilization and subsequent embryonic development was monitored. In experiment 1, the effects of aeration time and aeration combined with washing of EtO-gassed culture dishes on the extent of residual toxicity were investigated. There was no cleavage in any treatment in which oocytes were matured and fertilized in dishes exposed to EtO. EtO residues caused functional degeneration of oocytes even when culture dishes were aerated for more than 12 days post EtO-exposure and repeatedly washed. In experiment 2, the residual toxicity of EtO gas on in vitro maturation (IVM), in vitro fertilization (IVF) and in vitro culture (IVC) were evaluated. Cleavage rate significantly decreased and post-cleavage development was retarded in ova maintained in dishes treated with EtO either during IVM or IVF. EtO residues may be more detrimental to spermatozoa than to oocytes which may have been the primary cause of fertilization failure during IVF.

Effects of magnetic core geometry on false detection in residual current sensor

International Nuclear Information System (INIS)

Colin, Bruno; Chillet, Christian; Kedous-Lebouc, Afef; Mas, Patrick

2006-01-01

Under high-supply current, residual circuit breakers are subject to abnormal tripping, caused by false residual currents. Geometric or magnetic anomalies in the circuit breaker ring core seem to be responsible for these abnormal currents. This paper studies a few anomalies (spiral shape effect, conductor eccentricity, lamination effect) and calculates different contributions using the finite element simulations. The results show that the ring core, made of thin wound magnetic tape, is particularly sensitive to primary conductor eccentricity

Chemical modifications of therapeutic proteins induced by residual ethylene oxide.

Science.gov (United States)

Chen, Louise; Sloey, Christopher; Zhang, Zhongqi; Bondarenko, Pavel V; Kim, Hyojin; Ren, Da; Kanapuram, Sekhar

2015-02-01

Ethylene oxide (EtO) is widely used in sterilization of drug product primary containers and medical devices. The impact of residual EtO on protein therapeutics is of significant interest in the biopharmaceutical industry. The potential for EtO to modify individual amino acids in proteins has been previously reported. However, specific identification of EtO adducts in proteins and the effect of residual EtO on the stability of therapeutic proteins has not been reported to date. This paper describes studies of residual EtO with two therapeutic proteins, a PEGylated form of the recombinant human granulocyte colony-stimulating factor (Peg-GCSF) and recombinant human erythropoietin (EPO) formulated with human serum albumin (HSA). Peg-GCSF was filled in an EtO sterilized delivery device and incubated at accelerated stress conditions. Glu-C peptide mapping and LC-MS analyses revealed residual EtO reacted with Peg-GCSF and resulted in EtO modifications at two methionine residues (Met-127 and Met-138). In addition, tryptic peptide mapping and LC-MS analyses revealed residual EtO in plastic vials reacted with HSA in EPO formulation at Met-328 and Cys-34. This paper details the work conducted to understand the effects of residual EtO on the chemical stability of protein therapeutics. © 2014 Wiley Periodicals, Inc. and the American Pharmacists Association.

A review of residual stress analysis using thermoelastic techniques

Energy Technology Data Exchange (ETDEWEB)

Robinson, A F; Dulieu-Barton, J M; Quinn, S [University of Southampton, School of Engineering Sciences, Highfield, Southampton, SO17 1BJ (United Kingdom); Burguete, R L [Airbus UK Ltd., New Filton House, Filton, Bristol, BS99 7AR (United Kingdom)

2009-08-01

Thermoelastic Stress Analysis (TSA) is a full-field technique for experimental stress analysis that is based on infra-red thermography. The technique has proved to be extremely effective for studying elastic stress fields and is now well established. It is based on the measurement of the temperature change that occurs as a result of a stress change. As residual stress is essentially a mean stress it is accepted that the linear form of the TSA relationship cannot be used to evaluate residual stresses. However, there are situations where this linear relationship is not valid or departures in material properties due to manufacturing procedures have enabled evaluations of residual stresses. The purpose of this paper is to review the current status of using a TSA based approach for the evaluation of residual stresses and to provide some examples of where promising results have been obtained.

A review of residual stress analysis using thermoelastic techniques

International Nuclear Information System (INIS)

Robinson, A F; Dulieu-Barton, J M; Quinn, S; Burguete, R L

2009-01-01

Thermoelastic Stress Analysis (TSA) is a full-field technique for experimental stress analysis that is based on infra-red thermography. The technique has proved to be extremely effective for studying elastic stress fields and is now well established. It is based on the measurement of the temperature change that occurs as a result of a stress change. As residual stress is essentially a mean stress it is accepted that the linear form of the TSA relationship cannot be used to evaluate residual stresses. However, there are situations where this linear relationship is not valid or departures in material properties due to manufacturing procedures have enabled evaluations of residual stresses. The purpose of this paper is to review the current status of using a TSA based approach for the evaluation of residual stresses and to provide some examples of where promising results have been obtained.

Effects of Cutting Edge Microgeometry on Residual Stress in Orthogonal Cutting of Inconel 718 by FEM.

Science.gov (United States)

Shen, Qi; Liu, Zhanqiang; Hua, Yang; Zhao, Jinfu; Lv, Woyun; Mohsan, Aziz Ul Hassan

2018-06-14

Service performance of components such as fatigue life are dramatically influenced by the machined surface and subsurface residual stresses. This paper aims at achieving a better understanding of the influence of cutting edge microgeometry on machined surface residual stresses during orthogonal dry cutting of Inconel 718. Numerical and experimental investigations have been conducted in this research. The cutting edge microgeometry factors of average cutting edge radius S¯, form-factor K , and chamfer were investigated. An increasing trend for the magnitudes of both tensile and compressive residual stresses was observed by using larger S¯ or introducing a chamfer on the cutting edges. The ploughing depth has been predicted based on the stagnation zone. The increase of ploughing depth means that more material was ironed on the workpiece subsurface, which resulted in an increase in the compressive residual stress. The thermal loads were leading factors that affected the surface tensile residual stress. For the unsymmetrical honed cutting edge with K = 2, the friction between tool and workpiece and tensile residual stress tended to be high, while for the unsymmetrical honed cutting edge with K = 0.5, the high ploughing depth led to a higher compressive residual stress. This paper provides guidance for regulating machine-induced residual stress by edge preparation.

Effect of residual stress on the nanoindentation response of (100) copper single crystal

International Nuclear Information System (INIS)

Zhu, Li-na; Xu, Bin-shi; Wang, Hai-dou; Wang, Cheng-biao

2012-01-01

Experimental measurements were used to investigate the effect of residual stress on the nanoindentation of (100) copper single crystal. Equi-biaxial tensile and compressive stresses were applied to the copper single crystal using a special designed apparatus. It was found that residual stresses greatly affected peak load, curvature of the loading curve, elastically recovered depth, residual depth, indentation work, pile-up amount and contact area. The Suresh and Giannakopoulos and Lee and Kwon methods were used to calculate the residual stresses from load-depth data and morphology observation of nanoindents using atomic force microscopy. Comparison of the obtained results with stress values from strain gage showed that the residual stresses analyzed from the Suresh and Giannakopoulos model agreed well with the applied stresses. -- Highlights: ► Residual stresses greatly affected various nanoindentation parameters. ► The contact area can be accurately measured from AFM observation. ► The residual stresses analyzed from the S and G model agreed well with applied stresses.

The Effect of Creep on the Residual Stresses Generated During Silicon Sheet Growth

Science.gov (United States)

Hutchinson, J. W.; Lambropoulos, J. C.

1984-01-01

The modeling of stresses generated during the growth of thin silicon sheets at high speeds is an important part of the EFG technique since the experimental measurement of the stresses is difficult and prohibitive. The residual stresses which arise in such a growth process lead to serious problems which make thin Si ribbons unsuitable for fabrication. The constitutive behavior is unrealistic because at high temperature (close to the melting point) Si exhibits considerable creep which significantly relaxes the residual stresses. The effect of creep on the residual stresses generated during the growth of Si sheets at high speeds was addressed and the basic qualitative effect of creep are reported.

Fate and possible nutritional and toxicological significance of methylbromide residues in fumigated cocoa beans. Coordinated programme on isotopic tracer-aided studies on foreign chemical residues in food

International Nuclear Information System (INIS)

Adomako, D.

1975-03-01

Methyl bromide residues in cocoa as a result of fumigation under practical conditions have been studied. Cocoa beans were exposed to 14 C-labelled CH 3 Br for 24 hours at 20-32degC and dosage 23.5 to 28mg/1 of fumigants (moisture content of 6-7%). Whole unroasted beans and their shells and nibs as well as shells and nibs of roasted (105degC for 30 min) beans were extracted separately with toluene (for free CH 3 Br) and the dried residues wet combusted. 14 C-activities were determined by liquid scintillation counting. Total methyl bromide (bound and free) was equivalent 83-98ppm in whole unroasted beans 35 hours after treatment and aeration, and 31, 15 and 10ppm after 7, 42 and 70 days respectively in one set of experiments and 37, 53 and 42ppm after 76, 60 and 51 days in another set. Approximately 80% of the residue occurred in the shells which constitute only 12 to 13% of unroasted beans. 99% of the total residues appeared to be in chemically-bound form. Roasting reduced the total residues by 32 to 62% in nibs and 3.6 to 14% in shells. A striking effect of roasting was the occurrence in roasted nibs of residues as (extractable) carbon-14 (62-82% of the total residues compared to 16.5 - 27% in unroasted nibs). The bound residues behaved as methylated derivatives whilst the volatile fraction behaved as volatile aroma compounds formed by Maillard type reactions from the 14 C-labelled amino acides and sugars

Reclamation of plutonium from pyrochemical processing residues

International Nuclear Information System (INIS)

Gray, L.W.; Gray, J.H.; Holcomb, H.P.; Chostner, D.F.

1987-04-01

Savannah River Laboratory (SRL), Savannah River Plant (SRP), and Rocky Flats Plant (RFP) have jointly developed a process to recover plutonium from molten salt extraction residues. These NaCl, KCL, and MgCl 2 residues, which are generated in the pyrochemical extraction of 241 Am from aged plutonium metal, contain up to 25 wt % dissolved plutonium and up to 2 wt % americium. The overall objective was to develop a process to convert these residues to a pure plutonium metal product and discardable waste. To meet this objective a combination of pyrochemical and aqueous unit operations was used. The first step was to scrub the salt residue with a molten metal (aluminum and magnesium) to form a heterogeneous ''scrub alloy'' containing nominally 25 wt % plutonium. This unit operation, performed at RFP, effectively separated the actinides from the bulk of the chloride salts. After packaging in aluminum cans, the ''scrub alloy'' was then dissolved in a nitric acid - hydrofluoric acid - mercuric nitrate solution at SRP. Residual chloride was separated from the dissolver solution by precipitation with Hg 2 (NO 3 ) 2 followed by centrifuging. Plutonium was then separated from the aluminum, americium and magnesium using the Purex solvent extraction system. The 241 Am was diverted to the waste tank farm, but could be recovered if desired

Biodrying of animal slaughterhouse residues and heat production

Energy Technology Data Exchange (ETDEWEB)

Bernard, Y. [Centre de recherche industrielle, Quebec City, PQ (Canada)

2010-07-01

Animal carcasses from slaughterhouses are usually composted on farms, but the composting process is not optimized and a large volumes of carbonaceous residues are needed. This type of composting takes place over a period of 6 to 9 months in a nonaerated static pile. Quebec's industrial research centre (CRIQ) developed an organic biodrying process (BIOSECO) adapted to large-scale operations in order to optimize the treatment of slaughterhouse residues. Biodrying is a form of composting, in which the thermophilic phase is optimized, making it possible to evaporate large amounts of water. Biodrying is done inside a building and reduces the amount of carbonaceous residues considerably. The process is optimized by the sequence in which the slaughterhouse residues are added, the choice of input and the aeration flow. Slaughterhouse residues can be treated non-stop throughout the entire year. Since the odours are nearly completed limited to the building, the biodrying can be done near the slaughterhouse. A large amount of heat was produced by the process during the pilot project. It was concluded that the BIOSECO biodrying process is suitable for treating slaughterhouse residues in an effective and economic manner, and has the added advantage of producing heat that could be used for various purposes.

Analysis of binding properties and specificity through identification of the interface forming residues (IFR for serine proteases in silico docked to different inhibitors

Directory of Open Access Journals (Sweden)

da Silveira Carlos H

2010-10-01

Full Text Available Abstract Background Enzymes belonging to the same super family of proteins in general operate on variety of substrates and are inhibited by wide selection of inhibitors. In this work our main objective was to expand the scope of studies that consider only the catalytic and binding pocket amino acids while analyzing enzyme specificity and instead, include a wider category which we have named the Interface Forming Residues (IFR. We were motivated to identify those amino acids with decreased accessibility to solvent after docking of different types of inhibitors to sub classes of serine proteases and then create a table (matrix of all amino acid positions at the interface as well as their respective occupancies. Our goal is to establish a platform for analysis of the relationship between IFR characteristics and binding properties/specificity for bi-molecular complexes. Results We propose a novel method for describing binding properties and delineating serine proteases specificity by compiling an exhaustive table of interface forming residues (IFR for serine proteases and their inhibitors. Currently, the Protein Data Bank (PDB does not contain all the data that our analysis would require. Therefore, an in silico approach was designed for building corresponding complexes The IFRs are obtained by "rigid body docking" among 70 structurally aligned, sequence wise non-redundant, serine protease structures with 3 inhibitors: bovine pancreatic trypsin inhibitor (BPTI, ecotine and ovomucoid third domain inhibitor. The table (matrix of all amino acid positions at the interface and their respective occupancy is created. We also developed a new computational protocol for predicting IFRs for those complexes which were not deciphered experimentally so far, achieving accuracy of at least 0.97. Conclusions The serine proteases interfaces prefer polar (including glycine residues (with some exceptions. Charged residues were found to be uniquely prevalent at the

Analysis of binding properties and specificity through identification of the interface forming residues (IFR) for serine proteases in silico docked to different inhibitors.

Science.gov (United States)

Ribeiro, Cristina; Togawa, Roberto C; Neshich, Izabella A P; Mazoni, Ivan; Mancini, Adauto L; Minardi, Raquel C de Melo; da Silveira, Carlos H; Jardine, José G; Santoro, Marcelo M; Neshich, Goran

2010-10-20

Enzymes belonging to the same super family of proteins in general operate on variety of substrates and are inhibited by wide selection of inhibitors. In this work our main objective was to expand the scope of studies that consider only the catalytic and binding pocket amino acids while analyzing enzyme specificity and instead, include a wider category which we have named the Interface Forming Residues (IFR). We were motivated to identify those amino acids with decreased accessibility to solvent after docking of different types of inhibitors to sub classes of serine proteases and then create a table (matrix) of all amino acid positions at the interface as well as their respective occupancies. Our goal is to establish a platform for analysis of the relationship between IFR characteristics and binding properties/specificity for bi-molecular complexes. We propose a novel method for describing binding properties and delineating serine proteases specificity by compiling an exhaustive table of interface forming residues (IFR) for serine proteases and their inhibitors. Currently, the Protein Data Bank (PDB) does not contain all the data that our analysis would require. Therefore, an in silico approach was designed for building corresponding complexes. The IFRs are obtained by "rigid body docking" among 70 structurally aligned, sequence wise non-redundant, serine protease structures with 3 inhibitors: bovine pancreatic trypsin inhibitor (BPTI), ecotine and ovomucoid third domain inhibitor. The table (matrix) of all amino acid positions at the interface and their respective occupancy is created. We also developed a new computational protocol for predicting IFRs for those complexes which were not deciphered experimentally so far, achieving accuracy of at least 0.97. The serine proteases interfaces prefer polar (including glycine) residues (with some exceptions). Charged residues were found to be uniquely prevalent at the interfaces between the "miscellaneous-virus" subfamily

Effect of handling and processing on pesticide residues in food- a review.

Science.gov (United States)

Bajwa, Usha; Sandhu, Kulwant Singh

2014-02-01

Pesticides are one of the major inputs used for increasing agricultural productivity of crops. The pesticide residues, left to variable extent in the food materials after harvesting, are beyond the control of consumer and have deleterious effect on human health. The presence of pesticide residues is a major bottleneck in the international trade of food commodities. The localization of pesticides in foods varies with the nature of pesticide molecule, type and portion of food material and environmental factors. The food crops treated with pesticides invariably contain unpredictable amount of these chemicals, therefore, it becomes imperative to find out some alternatives for decontamination of foods. The washing with water or soaking in solutions of salt and some chemicals e.g. chlorine, chlorine dioxide, hydrogen peroxide, ozone, acetic acid, hydroxy peracetic acid, iprodione and detergents are reported to be highly effective in reducing the level of pesticides. Preparatory steps like peeling, trimming etc. remove the residues from outer portions. Various thermal processing treatments like pasteurization, blanching, boiling, cooking, steaming, canning, scrambling etc. have been found valuable in degradation of various pesticides depending upon the type of pesticide and length of treatment. Preservation techniques like drying or dehydration and concentration increase the pesticide content many folds due to concentration effect. Many other techniques like refining, fermentation and curing have been reported to affect the pesticide level in foods to varied extent. Milling, baking, wine making, malting and brewing resulted in lowering of pesticide residue level in the end products. Post harvest treatments and cold storage have also been found effective. Many of the decontamination techniques bring down the concentration of pesticides below MRL. However, the diminution effect depends upon the initial concentration at the time of harvest, substrate/food and type of

Residual N effects from livestock manure inputs to soils

DEFF Research Database (Denmark)

Schröder, Jaap; Bechini, Luca; Bittman, Shabtai

Organic inputs including livestock manures provide nitrogen (N) to crops beyond the year of their application. This so-called residual N effect should be taken into account when making decisions on N rates for individual fields, but also when interpreting N response trials in preparation...

Americium recovery from reduction residues

Science.gov (United States)

Conner, W.V.; Proctor, S.G.

1973-12-25

A process for separation and recovery of americium values from container or bomb'' reduction residues comprising dissolving the residues in a suitable acid, adjusting the hydrogen ion concentration to a desired level by adding a base, precipitating the americium as americium oxalate by adding oxalic acid, digesting the solution, separating the precipitate, and thereafter calcining the americium oxalate precipitate to form americium oxide. (Official Gazette)

On the Rule of Mixtures for Predicting Stress-Softening and Residual Strain Effects in Biological Tissues and Biocompatible Materials

Directory of Open Access Journals (Sweden)

Alex Elías-Zúñiga

2014-01-01

Full Text Available In this work, we use the rule of mixtures to develop an equivalent material model in which the total strain energy density is split into the isotropic part related to the matrix component and the anisotropic energy contribution related to the fiber effects. For the isotropic energy part, we select the amended non-Gaussian strain energy density model, while the energy fiber effects are added by considering the equivalent anisotropic volumetric fraction contribution, as well as the isotropized representation form of the eight-chain energy model that accounts for the material anisotropic effects. Furthermore, our proposed material model uses a phenomenological non-monotonous softening function that predicts stress softening effects and has an energy term, derived from the pseudo-elasticity theory, that accounts for residual strain deformations. The model’s theoretical predictions are compared with experimental data collected from human vaginal tissues, mice skin, poly(glycolide-co-caprolactone (PGC25 3-0 and polypropylene suture materials and tracheal and brain human tissues. In all cases examined here, our equivalent material model closely follows stress-softening and residual strain effects exhibited by experimental data.

On the Rule of Mixtures for Predicting Stress-Softening and Residual Strain Effects in Biological Tissues and Biocompatible Materials

Science.gov (United States)

Elías-Zúñiga, Alex; Baylón, Karen; Ferrer, Inés; Serenó, Lídia; Garcia-Romeu, Maria Luisa; Bagudanch, Isabel; Grabalosa, Jordi; Pérez-Recio, Tania; Martínez-Romero, Oscar; Ortega-Lara, Wendy; Elizalde, Luis Ernesto

2014-01-01

In this work, we use the rule of mixtures to develop an equivalent material model in which the total strain energy density is split into the isotropic part related to the matrix component and the anisotropic energy contribution related to the fiber effects. For the isotropic energy part, we select the amended non-Gaussian strain energy density model, while the energy fiber effects are added by considering the equivalent anisotropic volumetric fraction contribution, as well as the isotropized representation form of the eight-chain energy model that accounts for the material anisotropic effects. Furthermore, our proposed material model uses a phenomenological non-monotonous softening function that predicts stress softening effects and has an energy term, derived from the pseudo-elasticity theory, that accounts for residual strain deformations. The model’s theoretical predictions are compared with experimental data collected from human vaginal tissues, mice skin, poly(glycolide-co-caprolactone) (PGC25 3-0) and polypropylene suture materials and tracheal and brain human tissues. In all cases examined here, our equivalent material model closely follows stress-softening and residual strain effects exhibited by experimental data. PMID:28788466

Effects of oil and oil burn residues on seabird feathers

DEFF Research Database (Denmark)

Fritt-Rasmussen, Janne; Linnebjerg, Jannie Fries; Sørensen, Martin X.

2016-01-01

It is well known, that in case of oil spill, seabirds are among the groups of animals most vulnerable. Even small amounts of oil can have lethal effects by destroying the waterproofing of their plumage, leading to loss of insulation and buoyancy. In the Arctic these impacts are intensified....... To protect seabirds, a rapid removal of oil is crucial and in situ burning could be an efficient method. In the present work exposure effects of oil and burn residue in different doses was studied on seabird feathers from legally hunted Common eider (Somateria mollissima) by examining changes in total weight...... of the feather and damages on the microstructure (Amalgamation Index) of the feathers before and after exposure. The results of the experiments indicate that burn residues from in situ burning of an oil spill have similar or larger fouling and damaging effects on seabird feathers, as compared to fresh oil....

EFFECT OF LIGNIN CONTENT ON ENZYMATIC HYDROLYSIS OF FURFURAL RESIDUES

Directory of Open Access Journals (Sweden)

Jianxin Jiang

2011-02-01

Full Text Available The enzymatic saccharification of pretreated furfural residues with different lignin content was studied to verify the effect of lignin removal in the hydrolysis process. The results showed that the glucose yield was improved by increasing the lignin removal. A maximum glucose yield of 96.8% was obtained when the residue with a lignin removal of 51.4% was hydrolyzed for 108 h at an enzyme loading of 25 FPU/g cellulose. However, further lignin removal did not increase the hydrolysis. The effect of enzyme loading on the enzymatic hydrolysis was also explored in this work. It was concluded that a high glucose yield of 90% was achieved when the enzyme dosage was reduced from 25 to 15 FPU/g cellulose, which was cost-effective for the sugar and ethanol production. The structures of raw material and delignified samples were further characterized by XRD and scanning electron microscopy (SEM.

Effect of inorganic chelate of zinc and restaurant residual oil added ...

African Journals Online (AJOL)

Effect of inorganic chelate of zinc and restaurant residual oil added to feed mixture ... The interaction effects of RRO and ZnO did not result to a significant change in ... Therefore, the effects of RRO deteriorated the quality of meat by raising the ...

Effect of residual stresses on fatigue strength of plasma nitrided 4140 steel

International Nuclear Information System (INIS)

Aghazadeh, J.; Amidi, M.R.

2004-01-01

Almost every method that has been presented to determine residual stress has some limitation and complexities. The aim of this work is to present a new, yet simple method so called strain indentation for measuring the residual stresses particularly in thin layers. In this method in addition to the precision measurements, components of residual stress at different directions may be determined. AISI 4140 steel specimens nitrided at 350 d ig C , 450 d ig C and 550 d ig C for 5 hours in the mixture of 75% nitrogen- 25% hydrogen gas. The, components of residual stress in the radials axial and hoop directions in the nitrided layer were determined considering the elastic strain recovery after removal of residual stress inducer(i.e. the nitrided layer). Fatigue strength of the nitrided specimens was obtained by plotting the S-N curves and fractographic studies carried out on the fracture surface of the specimens. The effect of residual stress on the stress pattern was simulated. The calculated residual stress components were in the range of 40-210 Mpa and the radial components of residual stress were more than the other two directions. Maximum fatigue strength improvement of up to 110% was observed in the plasma nitrided specimens at 550 d ig C and also 40% improvement in fatigue strength was detected by increasing the nitriding temperature from 350 d ig C to 550 d ig C . This was due to 100% increase in residual stress. Fatigue crack growth velocity in the hoop direction was more than that of radial direction. This seems to be due to higher radial residual stress component compared with the hoop stress component in the sub layer

Rare Earth Element Phases in Bauxite Residue

Directory of Open Access Journals (Sweden)

Johannes Vind

2018-02-01

Full Text Available The purpose of present work was to provide mineralogical insight into the rare earth element (REE phases in bauxite residue to improve REE recovering technologies. Experimental work was performed by electron probe microanalysis with energy dispersive as well as wavelength dispersive spectroscopy and transmission electron microscopy. REEs are found as discrete mineral particles in bauxite residue. Their sizes range from <1 μm to about 40 μm. In bauxite residue, the most abundant REE bearing phases are light REE (LREE ferrotitanates that form a solid solution between the phases with major compositions (REE,Ca,Na(Ti,FeO3 and (Ca,Na(Ti,FeO3. These are secondary phases formed during the Bayer process by an in-situ transformation of the precursor bauxite LREE phases. Compared to natural systems, the indicated solid solution resembles loparite-perovskite series. LREE particles often have a calcium ferrotitanate shell surrounding them that probably hinders their solubility. Minor amount of LREE carbonate and phosphate minerals as well as manganese-associated LREE phases are also present in bauxite residue. Heavy REEs occur in the same form as in bauxites, namely as yttrium phosphates. These results show that the Bayer process has an impact on the initial REE mineralogy contained in bauxite. Bauxite residue as well as selected bauxites are potentially good sources of REEs.

The effects of logging residue extraction for energy on ecosystem services and biodiversity: A synthesis.

Science.gov (United States)

Ranius, Thomas; Hämäläinen, Aino; Egnell, Gustaf; Olsson, Bengt; Eklöf, Karin; Stendahl, Johan; Rudolphi, Jörgen; Sténs, Anna; Felton, Adam

2018-03-01

We review the consequences for biodiversity and ecosystem services from the industrial-scale extraction of logging residues (tops, branches and stumps from harvested trees and small-diameter trees from thinnings) in managed forests. Logging residue extraction can replace fossil fuels, and thus contribute to climate change mitigation. The additional biomass and nutrients removed, and soils and other structures disturbed, have several potential environmental impacts. To evaluate potential impacts on ecosystem services and biodiversity we reviewed 279 scientific papers that compared logging residue extraction with non-extraction, the majority of which were conducted in Northern Europe and North America. The weight of available evidence indicates that logging residue extraction can have significant negative effects on biodiversity, especially for species naturally adapted to sun-exposed conditions and the large amounts of dead wood that are created by large-scaled forest disturbances. Slash extraction may also pose risks for future biomass production itself, due to the associated loss of nutrients. For water quality, reindeer herding, mammalian game species, berries, and natural heritage the results were complicated by primarily negative but some positive effects, while for recreation and pest control positive effects were more consistent. Further, there are initial negative effects on carbon storage, but these effects are transient and carbon stocks are mostly restored over decadal time perspectives. We summarize ways of decreasing some of the negative effects of logging residue extraction on specific ecosystem services, by changing the categories of residue extracted, and site or forest type targeted for extraction. However, we found that suggested pathways for minimizing adverse outcomes were often in conflict among the ecosystem services assessed. Compensatory measures for logging residue extraction may also be used (e.g. ash recycling, liming, fertilization

Residual N effects from livestock manure inputs to soils

NARCIS (Netherlands)

Schroder, J.J.; Bechini, L.; Bittman, S.; Brito, M.P.; Delin, S.; Lalor, S.T.J.; Morvan, T.; Chambers, B.J.; Sakrabani, R.; Sørensen, P.B.

2013-01-01

Organic inputs including livestock manures provide nitrogen (N) to crops beyond the year of their application. This so-called residual N effect should be taken into account when making decisions on N rates for individual fields, but also when interpreting N response trials in preparation of

Impact of Intrafraction and Residual Interfraction Effect on Prostate Proton Pencil Beam Scanning

International Nuclear Information System (INIS)

Tang, Shikui; Deville, Curtiland; Tochner, Zelig; Wang, Ken Kang-Hsin; McDonough, James; Vapiwala, Neha; Both, Stefan

2014-01-01

Purpose: To quantitatively evaluate the impact of interplay effect and plan robustness associated with intrafraction and residual interfraction prostate motion for pencil beam scanning proton therapy. Methods and Materials: Ten prostate cancer patients with weekly verification CTs underwent pencil beam scanning with the bilateral single-field uniform dose (SFUD) modality. A typical field had 10-15 energy layers and 500-1000 spots. According to their treatment logs, each layer delivery time was <1 s, with average time to change layers of approximately 8 s. Real-time intrafraction prostate motion was determined from our previously reported prospective study using Calypso beacon transponders. Prostate motion and beam delivering sequence of the worst-case scenario patient were synchronized to calculate the “true” dose received by the prostate. The intrafraction effect was examined by applying the worst-case scenario prostate motion on the planning CT, and the residual interfraction effect was examined on the basis of weekly CT scans. The resultant dose variation of target and critical structures was examined to evaluate the interplay effect. Results: The clinical target volume (CTV) coverage was degraded because of both effects. The CTV D 99 (percentage dose to 99% of the CTV) varied up to 10% relative to the initial plan in individual fractions. However, over the entire course of treatment the total dose degradation of D 99 was 2%-3%, with a standard deviation of <2%. Absolute differences between SFUD, intensity modulate proton therapy, and one-field-per-day SFUD plans were small. The intrafraction effect dominated over the residual interfraction effect for CTV coverage. Mean dose to the anterior rectal wall increased approximately 10% because of combined residual interfraction and intrafraction effects, the interfraction effect being dominant. Conclusions: Both intrafraction and residual interfraction prostate motion degrade CTV coverage within a clinically

Impact of Intrafraction and Residual Interfraction Effect on Prostate Proton Pencil Beam Scanning

Energy Technology Data Exchange (ETDEWEB)

Tang, Shikui, E-mail: shktang@gmail.com [Department of Radiation Oncology, University of Pennsylvania, Philadelphia, Pennsylvania (United States); ProCure Proton Therapy Center, Somerset, New Jersey (United States); Deville, Curtiland; Tochner, Zelig [Department of Radiation Oncology, University of Pennsylvania, Philadelphia, Pennsylvania (United States); Wang, Ken Kang-Hsin [Department of Radiation Oncology, University of Pennsylvania, Philadelphia, Pennsylvania (United States); Department of Radiation Oncology and Molecular Radiation Sciences, Johns Hopkins University, Baltimore, Maryland (United States); McDonough, James; Vapiwala, Neha; Both, Stefan [Department of Radiation Oncology, University of Pennsylvania, Philadelphia, Pennsylvania (United States)

2014-12-01

Purpose: To quantitatively evaluate the impact of interplay effect and plan robustness associated with intrafraction and residual interfraction prostate motion for pencil beam scanning proton therapy. Methods and Materials: Ten prostate cancer patients with weekly verification CTs underwent pencil beam scanning with the bilateral single-field uniform dose (SFUD) modality. A typical field had 10-15 energy layers and 500-1000 spots. According to their treatment logs, each layer delivery time was <1 s, with average time to change layers of approximately 8 s. Real-time intrafraction prostate motion was determined from our previously reported prospective study using Calypso beacon transponders. Prostate motion and beam delivering sequence of the worst-case scenario patient were synchronized to calculate the “true” dose received by the prostate. The intrafraction effect was examined by applying the worst-case scenario prostate motion on the planning CT, and the residual interfraction effect was examined on the basis of weekly CT scans. The resultant dose variation of target and critical structures was examined to evaluate the interplay effect. Results: The clinical target volume (CTV) coverage was degraded because of both effects. The CTV D{sub 99} (percentage dose to 99% of the CTV) varied up to 10% relative to the initial plan in individual fractions. However, over the entire course of treatment the total dose degradation of D{sub 99} was 2%-3%, with a standard deviation of <2%. Absolute differences between SFUD, intensity modulate proton therapy, and one-field-per-day SFUD plans were small. The intrafraction effect dominated over the residual interfraction effect for CTV coverage. Mean dose to the anterior rectal wall increased approximately 10% because of combined residual interfraction and intrafraction effects, the interfraction effect being dominant. Conclusions: Both intrafraction and residual interfraction prostate motion degrade CTV coverage within a

Evaluation of machining effect for the residual stress of SA508 by hole drilling method

International Nuclear Information System (INIS)

Lee, Jeong Kun; Lee, Kyoung Soo; Song, Ki O; Kim, Young Shin

2009-01-01

Residual stresses on a surface of the material are welcome or undesirable since it's direction, compression or tensile. But especially for the fatigue, it is not negligible effect on the material strength. These residual stresses developed during the manufacturing processes involving material deformation, heat treatment, machining. The object of this paper is verifying the effect of machining what is mostly used for SA508. For verifying the effect of machining, three different kind of machining have been achieved, milling, grinding, wire cutting. Also to measure the residual stress, hole drill method and indentation method are used.

The effect of commercial processing procedures on 14C-carbendazim residues in soybean oil and tomato

International Nuclear Information System (INIS)

Peng Genyuan; Wang Huaguo; Qi Mengwen; Wang Fujun; Zhou Changjiu

1994-01-01

Under simulated agricultural practices, soybean plants were treated with 14 C-labelled carbendazim during the blooming stage. The residue in seeds was determined to be 0.067 ppm; corresponding to 0.076 ppm respectively. After subjecting the oil to degumming, alkali treatment, bleaching and deodorization, 53.7% of original radioactivity was removed. Deodorization was the most effect process, removing about 20% of the residue. The concentration of residues in the deodorized oil decreased about 30%. In soybean seed and cake, the residue was mainly present as carbendazim, the concentration of the other metabolites did not exceed 30% of the residue. Tomatoes grown on a field plot were treated with 14 C-carbendazim. After harvest, the tomatoes were processed into tomato juice and canned whole fruit. The magnitude and nature of residues in samples taken at several processing steps were determined to evaluate the effect of commercial processing on removing or eliminating the residues. The results showed that the surface residues on tomato would be removed efficiently by simple washing of tomato. A buffer solution of phosphate had the highest efficiency. Tomato juice contained lower residues than canned whole fruit

Soil and vegetation changes after clear-felling coniferous forests: effects of varying removal of logging residues

International Nuclear Information System (INIS)

Olsson, Bengt.

1995-01-01

Effects of the intensity of logging residue harvesting on soil nutrient status and ground vegetation cover were examined over a 16-year period in two series of field experiments in Sweden. Short-term effects of slash harvesting and stump removal on soil water chemistry were studied after clear-felling a Norway spruce (Picea abies (L.) Karst.) stand in SW Sweden. Soil water concentrations of NH4 + , and NO 3 - and K + were lower shortly after whole-tree harvesting (i.e. stem and slash harvesting) than shortly after conventional stem-only harvesting or complete tree harvesting (i.e. stem, slash and stump removal). However, 5 years later there were no longer differences in nutrient concentrations detected between treatments, and nutrient levels approached those normally found in drainage water from forest land. Similar studies focussed on long-term (16 years) effects were conducted on four coniferous forest sites in Sweden, two in north and the other two in the south. In each region one site was situated in a pure Scots pine stand (Pinus sylvestris L.) and the other in a pure Norway spruce stand. In general, the intensity of slash harvesting had no effect on the total pools of nitrogen or carbon in the soil. Furthermore, this study showed experimentally that the harvesting of logging residues results in long-term soil acidification and depletions of exchangeable base cations, manganese and zinc pools, which lead in turn to a reduction in base saturation levels. A major implication for practical forestry was that guidelines and recommendations concerning the large-scale utilization of logging residues should be based more on the nutritional and soil acidifying consequences of this practice than on its potential effect on soil organic matter storage. It would also be possible to mitigate the detrimental effects that slash harvesting has on site conditions by applying wood-ash or other nutrients in inorganic form. 53 refs, 4 figs, 4 tabs

Soil and vegetation changes after clear-felling coniferous forests: effects of varying removal of logging residues

Energy Technology Data Exchange (ETDEWEB)

Olsson, Bengt

1995-11-01

Effects of the intensity of logging residue harvesting on soil nutrient status and ground vegetation cover were examined over a 16-year period in two series of field experiments in Sweden. Short-term effects of slash harvesting and stump removal on soil water chemistry were studied after clear-felling a Norway spruce (Picea abies (L.) Karst.) stand in SW Sweden. Soil water concentrations of NH4{sup +}, and NO{sub 3}{sup -} and K{sup +} were lower shortly after whole-tree harvesting (i.e. stem and slash harvesting) than shortly after conventional stem-only harvesting or complete tree harvesting (i.e. stem, slash and stump removal). However, 5 years later there were no longer differences in nutrient concentrations detected between treatments, and nutrient levels approached those normally found in drainage water from forest land. Similar studies focussed on long-term (16 years) effects were conducted on four coniferous forest sites in Sweden, two in north and the other two in the south. In each region one site was situated in a pure Scots pine stand (Pinus sylvestris L.) and the other in a pure Norway spruce stand. In general, the intensity of slash harvesting had no effect on the total pools of nitrogen or carbon in the soil. Furthermore, this study showed experimentally that the harvesting of logging residues results in long-term soil acidification and depletions of exchangeable base cations, manganese and zinc pools, which lead in turn to a reduction in base saturation levels. A major implication for practical forestry was that guidelines and recommendations concerning the large-scale utilization of logging residues should be based more on the nutritional and soil acidifying consequences of this practice than on its potential effect on soil organic matter storage. It would also be possible to mitigate the detrimental effects that slash harvesting has on site conditions by applying wood-ash or other nutrients in inorganic form. 53 refs, 4 figs, 4 tabs

Effects of processing treatment on pesticide residues in fruits and their products

International Nuclear Information System (INIS)

Mao Xuefei; Jiao Bining; Fu Chenmei; Qian Yongzhong; Wang Jing

2008-01-01

The influence of processing treatments on pesticide residues in fruits and their products was reviewed. The effects on pesticide residues and relative control treatments for each processing step, including peeling, washing, sterilization, juicing, clarification, filtration, drying and fermentation, were discussed, respectively. Meanwhile we analyzed the future development prospectin of this field, in order to provide some suggestions for commercial fruit industry and consumers' health. (authors)

Effect of cooking on enrofloxacin residues in chicken tissue.

Science.gov (United States)

Lolo, M; Pedreira, S; Miranda, J M; Vázquez, B I; Franco, C M; Cepeda, A; Fente, C

2006-10-01

The aim of this study was to determine the effect of different cooking processes (microwaving, roasting, boiling, grilling and frying) on naturally incurred enrofloxacin residues in chicken muscle. Enrofloxacin and its metabolite, ciprofloxacin, were analysed using a validated LC-MS method with limits of detection (LOD) and quantification (LOQ), respectively, of 2 and 5 ng g-1 quinolones in muscle samples. The method was shown to be linear over the range 5-500 ng g-1. Mean intra-day relative standard deviation (RSD) at a concentration of 50 ng g-1 (n = 6) was 6%; inter-day RSD was 12%. A recovery study demonstrated that 65-101%, of the drug and metabolite could be recovered from the tissue. The RSD with naturally incurred roasted chicken breast was 9.18% at a concentration of 11 +/- 1.01 ng g-1 (n = 6). In water, enrofloxacin remained stable for 3 h when heated at 100 degrees C. It was concluded that residue data from raw tissue are valid for estimation of consumer exposure to this drug, as well as the ADI calculations because cooking procedures did not affect enrofloxacin residues, which remained stable during heating. However, there was an apparent decrease in quinolone concentration in tissue because some was lost by exudation into the liquid used for cooking. Conversely, for a cooking procedure with water loss, there was an apparent increase in residue concentration.

Residual stress measurement of large scaled welded pipe using neutron diffraction method. Effect of SCC crack propagation and repair weld on residual stress distribution

International Nuclear Information System (INIS)

Suzuki, Hiroshi; Katsuyama, Jinya; Tobita, Tohru; Morii, Yukio

2011-01-01

The RESA-1 neutron engineering diffractometer in the JRR-3 (Japan Research Reactor No.3) at the Japan Atomic Energy Agency, which is used for stress measurements, was upgraded to realize residual stress measurements of large scaled mechanical components. A series of residual stress measurements was made to obtain through-thickness residual stress distributions in a Type 304 stainless steel butt-welded pipe of 500A-sch.80 using the upgraded RESA-1 diffractometer. We evaluated effects of crack propagation such as stress corrosion cracking (SCC) and a part-circumference repair weld on the residual stress distributions induced by girth welding. Measured residual stress distributions near original girth weld revealed good agreement with typical results shown in some previous works using finite element method, deep hole drilling as well as neutron diffraction. After introducing a mock crack with 10 mm depth in the heat affected zone on the inside wall of the pipe by electro discharge machining, the axial residual stresses were found to be released in the part of the mock crack. However, changes in the through-wall bending stress component and the self-equilibrated stress component were negligible and hence the axial residual stress distribution in the ligament was remained in the original residual stresses near girth weld without the mock crack. Furthermore, changes in hoop and radial residual stress were also small. The residual stress distributions after a part repair welding on the outer circumference of the girth weld were significantly different from residual stress distributions near the original girth weld. The through-thickness average axial residual stress was increased due to increase of the tensile membrane stress and mitigation of the bending stress after repair welding. Throughout above studies, we evidenced that the neutron diffraction technique is useful and powerful tool for measuring residual stress distributions in large as well as thick mechanical

Functional form diagnostics for Cox's proportional hazards model.

Science.gov (United States)

León, Larry F; Tsai, Chih-Ling

2004-03-01

We propose a new type of residual and an easily computed functional form test for the Cox proportional hazards model. The proposed test is a modification of the omnibus test for testing the overall fit of a parametric regression model, developed by Stute, González Manteiga, and Presedo Quindimil (1998, Journal of the American Statistical Association93, 141-149), and is based on what we call censoring consistent residuals. In addition, we develop residual plots that can be used to identify the correct functional forms of covariates. We compare our test with the functional form test of Lin, Wei, and Ying (1993, Biometrika80, 557-572) in a simulation study. The practical application of the proposed residuals and functional form test is illustrated using both a simulated data set and a real data set.

Effect of Residue Nitrogen Concentration and Time Duration on Carbon Mineralization Rate of Alfalfa Residues in Regions with Different Climatic Conditions

Directory of Open Access Journals (Sweden)

saeid shafiei

2017-08-01

Full Text Available Introduction Various factors like climatic conditions, vegetation, soil properties, topography, time, plant residue quality and crop management strategies affect the decomposition rate of organic carbon (OC and its residence time in soil. Plant residue management concerns nutrients recycling, carbon recycling in ecosystems and the increasing CO2 concentration in the atmosphere. Plant residue decomposition is a fundamental process in recycling of organic matter and elements in most ecosystems. Soil management, particularly plant residue management, changes soil organic matter both qualitatively and quantitatively. Soil respiration and carbon loss are affected by soil temperature, soil moisture, air temperature, solar radiation and precipitation. In natural agro-ecosystems, residue contains different concentrations of nitrogen. It is important to understand the rate and processes involved in plant residue decomposition, as these residues continue to be added to the soil under different weather conditions, especially in arid and semi-arid climates. Material and methods Organic carbon mineralization of alfalfa residue with different nitrogen concentrations was assessed in different climatic conditions using split-plot experiments over time and the effects of climate was determined using composite analysis. The climatic conditions were classified as warm-arid (Jiroft, temperate arid (Narab and cold semi-arid (Sardouiyeh using cluster analysis and the nitrogen (N concentrations of alfalfa residue were low, medium and high. The alfalfa residue incubated for four different time periods (2, 4, 6 and 8 months. The dynamics of organic carbon in different regions measured using litter bags (20×10 cm containing 20 g alfalfa residue of 2-10 mm length which were placed on the soil surface. Results and discussion The results of this study showed that in a warm-arid (Jiroft, carbon loss and the carbon decomposition rate constant were low in a cold semi

Effect of land-use on the P forms of an Andisol

Directory of Open Access Journals (Sweden)

Carlos Henríquez

2015-11-01

Full Text Available The effect of agricultural land use on the forms of P in a Typic Hapludand was evaluated. An area of 8.4 ha composed of 3 adjacent lots, dedicated for over 20 years to secondary forest and plantings of sugarcane and coffee, was chosen at Juan Viñas, Costa Rica. Soil samples were taken using an 8x6 grid layout of sampling points, spaced at 40 m. Soil samples were analyzed with the P fractionation methodology proposed by Hedley et ál. (1982. Total P varied between 936 and 2516 mg.kg-1. Both coffee and sugar cane lots (1934 y 1754 mg.kg-1 respectively, showed the highest values of total-P compared with the forest (1419 mg.kg- 1, suggesting a positive overall balance of P due to its accumulation through the years. The coffee area showed the highest values of P-labile and P-sesquioxides-Fe/Al, which was related to usual higher fertilization compared with areas of sugarcane and forest. The greatest value of P-residual was found in sugarcane with almost 48% of total P. The P-organic varied 27 to 29% of the total suggesting its importance as valuable sink of P. We conclude that the type of land use had a significant effect on the forms of P which was observed in both the quantity and distributionof different forms of P in soil.

Effects of relative density and accumulated shear strain on post-liquefaction residual deformation

Directory of Open Access Journals (Sweden)

J. Kim

2013-10-01

Full Text Available The damage caused by liquefaction, which occurs following an earthquake, is usually because of settlement and lateral spreading. Generally, the evaluation of liquefaction has been centered on settlement, that is, residual volumetric strain. However, in actual soil, residual shear and residual volumetric deformations occur simultaneously after an earthquake. Therefore, the simultaneous evaluation of the two phenomena and the clarification of their relationship are likely to evaluate post-liquefaction soil behaviors more accurately. Hence, a quantitative evaluation of post-liquefaction damage will also be possible. In this study, the effects of relative density and accumulated shear strain on post-liquefaction residual deformations were reviewed through a series of lateral constrained-control hollow cylindrical torsion tests under undrained conditions. In order to identify the relationship between residual shear and residual volumetric strains, this study proposed a new test method that integrates monotonic loading after cyclic loading, and K0-drain after cyclic loading – in other words, the combination of cyclic loading, monotonic loading, and the K0 drain. In addition, a control that maintained the lateral constrained condition across all the processes of consolidation, cyclic loading, monotonic loading, and drainage was used to reproduce the anisotropy of in situ ground. This lateral constrain control was performed by controlling the axial strain, based on the assumption that under undrained conditions, axial and lateral strains occur simultaneously, and unless axial strain occurs, lateral strain does not occur. The test results confirmed that the recovery of effective stresses, which occur during monotonic loading and drainage after cyclic loading, respectively, result from mutually different structural restoration characteristics. In addition, in the ranges of 40–60% relative density and 50–100% accumulated shear strain, relative

Initial contents of residue quality parameters predict effects of larger soil fauna on decomposition of contrasting quality residues

Directory of Open Access Journals (Sweden)

Ratikorn Sanghaw

2017-10-01

Full Text Available A 52-week decomposition study employing the soil larger fauna exclusion technique through litter bags of two mesh sizes (20 and 0.135 mm was conducted in a long-term (18 yr field experiment. Organic residues of contrasting quality of N, lignin (L, polyphenols (PP and cellulose (CL all in grams per kilogram: rice straw (RS: 4.5N, 22.2L, 3.9PP, 449CL, groundnut stover (GN: 21.2N, 71.4L, 8.1PP, 361CL, dipterocarp leaf litter (DP: 5.1N, 303L, 68.9PP, 271CL and tamarind leaf litter (TM: 11.6N, 190L, 27.7PP, 212CL were applied to soil annually to assess and predict soil larger fauna effects (LFE on decomposition based on the initial contents of the residue chemical constituents. Mass losses in all residues were not different under soil fauna inclusion and exclusion treatments during the early stage (up to week 4 after residue incorporation but became significantly higher under the inclusion than the exclusion treatments during the later stage (week 8 onwards. LFE were highest (2–51% under the resistant DP at most decomposition stages. During the early stage (weeks 1–4, both the initial contents of labile (N and CL and recalcitrant C, and recalcitrant C interaction with labile constituents of residues showed significant correlations (r = 0.64–0.90 with LFE. In the middle stage (week 16, LFE under resistant DP and TM had significant positive correlations with L, L + PP and L/CL. They were also affected by these quality parameters as shown by the multiple regression analysis. In the later stages (weeks 26–52, the L/CL ratio was the most prominent quality parameter affecting LFE. Keywords: Mesofauna and macrofauna, Microorganisms, Recalcitrant and labile compounds, Residue chemical composition, Tropical sandy soil

Accounting for the residual stress effects on the creep deformation of channel tubes

International Nuclear Information System (INIS)

Knizhnikov, Yu.N.; Platonov, P.A.; Ul'yanov, A.I.

1985-01-01

The effect of the first kind residual stresses arising in the walls of the zirconium base alloy fules in the process of fabrication on the RBMK type reactor channel tube creep is investigated. Models for calculation of the reactor component creep with account for the relaxation of residual stresses distributed by the wall thickness as well as the radiation and temperature fields are developed. On the basis of the analysis of the data obtained it is concluded that the effect of the residual stresses on the RBMK channel tube deformation for a long-term operation is negligible. But for the short-term fests the results can be noticeably distorted by this factor. The role of internal stresses can also manifest when determining the deformation of radiation elongation of the zirconium base alloy samples

Thermal Aging Effects on Residual Stress and Residual Strain Distribution on Heat Affected Zone of Alloy 600 in Dissimilar Metal Weld

Energy Technology Data Exchange (ETDEWEB)

Ham, Junhyuk; Choi, Kyoung Joon; Kim, Ji Hyun [UNIST, Ulsan (Korea, Republic of)

2016-10-15

Dissimilar metal weld (DMW), consisting of Alloy 600, Alloy 182, and A508 Gr.3, has been widely used as a joining material of the reactor pressure vessel penetration nozzle and the steam generator tubing for pressurized water reactors (PWR) because of its good mechanical strength, thermal conductivity, and corrosion resistance. Residual tensile stress is mainly nominated as a cause of SCC in light water reactors by IAEA report. So, to relax the residual stress, post-weld heat treatment is required after manufacturing process such as welding. However, thermal treatment has a great effect on the microstructure and the chromium depletion profile on Alloy 600, so called sensitization. By this reason, HAZ on Alloy 600 is critical to crack. According to G.A. Young et al., Crack growth rates (CGR) in the Alloy 600 HAZ were about 30 times faster than those in the Alloy 600 base metal tested under the same conditions. And according to Z.P. Lu et al., CGR in the Alloy 600 HAZ can be more than 20 times higher than that in its base metal. There are some methods to measure the exact value of residual stress on the material surface. The most common way is X-ray diffraction method (XRD). The principle of XRD is based on lattice strains and depends on the changes in the spacing of the atomic planes in material. And there is a computer simulation method to estimate residual stress distribution which is called ANSYS. This study was conducted to investigate how thermal aging affects residual stress and residual strain distribution of Alloy 600 HAZ. Following conclusions can be drawn from this study. According to preceding researches and this study, both the relaxation of residual stress and the change of residual strain follow as similar way, spreading out from concentrated region. The result of Vickers micro-hardness tester shows that tensile residual stresses are distributed broadly on the material aged by 15 years. Therefore, HT400{sub Y}15 material is weakest state for PWSCC. The

Effects of Adopting Different Kinds of Collecting Method for Years on Film Residual Coefficient and Maize Yields

OpenAIRE

TANG Wen-xue; MA Zhong-ming; WEI Tao

2017-01-01

Wide usage of mulching technology has increased crop yields, but the large amounts of mulching film residue resulting from widespread use of plastic film in China has brought about a series of pollution hazards. Based on a 4-year (2011-2014) long-term experiment, the effects of different kinds of collecting mothod (zero plastic film residues, conventional plastic film residues, whole plastic film residues remainded) on plastic film residues, residual coefficient and maize yield were explored....

Methyl bromide residues in fumigated cocoa beans

International Nuclear Information System (INIS)

Adomako, D.

1975-01-01

The 14 C activity in unroasted [ 14 C]-methyl bromide fumigated cocoa beans was used to study the fate and persistence of CH 3 Br in the stored beans. About 70% of the residues occurred in the shells. Unchanged CH 3 Br could not be detected, all the sorbed CH 3 Br having reacted with bean constituents apparently to form 14 C-methylated derivatives and inorganic bromide. No 14 C activity was found in the lipid fraction. Roasting decreased the bound (non-volatile) residues, with corresponding changes in the activities and amounts of free sugars, free and protein amino acids. Roasted nibs and shells showed a two-fold increase in the volatile fraction of the 14 C residue. This fraction may be related to the volatile aroma compounds formed by Maillard-type reactions. (author)

Plant residues: short term effect on sulphate, borate, zinc and copper adsorption by an acid oxisol

Directory of Open Access Journals (Sweden)

Dias Ana Cristi Basile

2003-01-01

Full Text Available Laboratory experiments were carried out to examine the effects of plant residues on Cu, Zn, B and S adsorption by an acidic oxisol. The plant residues were: black oats (Avena strigosa, oil seed radish(Raphanus sativus, velvet beans (Stizolobium cinereum, and pigeon pea (Cajanus cajan collected at flowering stage. Plant residues increased Cu and Zn adsorptions and decreased B and S adsorptions. The results indicated that for short term effect plant residues decreased the availabilities of Cu and Zn through metal organic complex reactions and increased availabilities of S and B through competition with organic anions by the adsorption sites on soil.

Effects of the magnesium oxide thin films' microstructures on the residual stresses

Energy Technology Data Exchange (ETDEWEB)

He, Li-jun, E-mail: helijun4@126.com [The School of Optoelectronic Engineering, Chongqing University of Posts and Telecommunications, Chongqing 400065 (China); The State Key Laboratory of Electronic Thin Films and Integrated Devices, School of Microelectronics and Solid-State Electronics, University of Electronic Science and Technology of China, Chengdu 610054 (China); Wang, Li-yan [Electronic Information and Networking Research Institute, Collaborative Innovation Center for Information Communication Technology, Chongqing University of Posts and Telecommunications, Chongqing 400065 (China); Chen, Wei-Zhong [The School of Optoelectronic Engineering, Chongqing University of Posts and Telecommunications, Chongqing 400065 (China); Liu, Xing-zhao [The State Key Laboratory of Electronic Thin Films and Integrated Devices, School of Microelectronics and Solid-State Electronics, University of Electronic Science and Technology of China, Chengdu 610054 (China)

2016-09-15

The MgO thin films are deposited at various inclined angles. The morphology investigated by scanning electron microscope (SEM) shows the MgO thin films deposited at high inclined angles have columnar grain. The relationships between full width high maximum (FWHM) of ω-scan, residual stresses and the inclined angles are studied. The results show the smallest FWHM of MgO (002) is 4.968°, the residual stress of MgO thin films is compressive stress, and the residual stress of MgO thin films deposited at the inclined angle of 55° is the smallest. So the microstructures of MgO thin films fabricated by the oblique angle deposition (OAD) technique effectively control the residual stresses. - Highlights: • MgO thin films are deposited by oblique angle deposition technique. • The FWHMs of MgO is the smallest at the inclined angle of 55°. • Residual stress of MgO is the smallest at the inclined angle of 55°.

Springback effects during single point incremental forming: Optimization of the tool path

Science.gov (United States)

Giraud-Moreau, Laurence; Belchior, Jérémy; Lafon, Pascal; Lotoing, Lionel; Cherouat, Abel; Courtielle, Eric; Guines, Dominique; Maurine, Patrick

2018-05-01

Incremental sheet forming is an emerging process to manufacture sheet metal parts. This process is more flexible than conventional one and well suited for small batch production or prototyping. During the process, the sheet metal blank is clamped by a blank-holder and a small-size smooth-end hemispherical tool moves along a user-specified path to deform the sheet incrementally. Classical three-axis CNC milling machines, dedicated structure or serial robots can be used to perform the forming operation. Whatever the considered machine, large deviations between the theoretical shape and the real shape can be observed after the part unclamping. These deviations are due to both the lack of stiffness of the machine and residual stresses in the part at the end of the forming stage. In this paper, an optimization strategy of the tool path is proposed in order to minimize the elastic springback induced by residual stresses after unclamping. A finite element model of the SPIF process allowing the shape prediction of the formed part with a good accuracy is defined. This model, based on appropriated assumptions, leads to calculation times which remain compatible with an optimization procedure. The proposed optimization method is based on an iterative correction of the tool path. The efficiency of the method is shown by an improvement of the final shape.

THE EFFECT OF COOKING AND STORAGE ON FLORFENICOL AND FLORFENICOL AMINE RESIDUES IN EGGS

Directory of Open Access Journals (Sweden)

Ayhan Filazi

2015-09-01

Full Text Available The aim of this study was to evaluate the effects of storage conditions (room temperature, refrigerator and cooking methods (frying, boiling on florfenicol (FF and florfenicol amine (FFA residue levels in eggs. Without any significant difference between storage conditions at 20˚C and +4˚C, residue levels decreased within days, but were still present on day 28. Frying and boiling for 1 and 5 min yielded similar results to the storage conditions just described; there was a significant decrease in residue levels, but still not enough for decomposing. These findings indicate that FF and FFA residues are heat-labile.

Potassium as topdressing in maize and the residual effects on soybean grown in succession= Potássio em cobertura no milho e efeito residual na soja em sucessão

Directory of Open Access Journals (Sweden)

Tiago de Lisboa Parente

2016-10-01

Full Text Available Potassium (K is the second most-extracted nutrient by the majority of agricultural crops, and can influence fruiting, grain weight and other physiological processes. However, there are still questions regarding possible residual effects in areas of direct seeding. The aim of this study therefore, was to evaluate the immediate effects of K on second-crop maize, and the possible residual effect on soybean crops grown in succession under a no-tillage system. The experimental design was of randomised blocks with nine doses of K2 O as topdressing (0, 15, 30, 45, 60, 75, 90, 120 and 150 kg ha-1, in the form of KCl applied in the V6 vegetative growth stage of the maize, with four replications. The study was carried out in an area of Cerrado, with soybean grown in succession. Morphological and production characteristics were evaluated in the two crops. There was an increase in maize productivity up to the dose of maximum technical efficiency, 89 kg ha-1 K2 O, and in the soybean, up to 80 kg ha-1, in addition to the increase in the number of pods per plant and thousand grain weight. The results therefore, demonstrate the residual effect of K in soybean crops grown in succession. = O potássio (K é o segundo nutriente mais extraído pela maioria das culturas agrícolas, podendo influenciar na frutificação, peso de grãos e em outros processos fisiológicos. No entanto, ainda há questionamentos quanto ao seu possível efeito residual em áreas de plantio direto. Assim, objetivou-se com esse trabalho avaliar a eficiência imediata do K no milho, segunda safra, e o possível efeito residual na cultura da soja cultivada em sucessão no sistema plantio direto. O delineamento experimental foi em blocos casualizados com nove doses de K2 O em cobertura (0, 15, 30, 45, 60, 75, 90, 120 e 150 kg ha-1 na forma de KCl, aplicadas no estádio vegetativo V6 no milho, com quatro repetições. O estudo foi desenvolvido em área de Cerrado. Foram avaliados os caracteres

Effectiveness of stress release geometries on reducing residual stress in electroforming metal microstructure

Science.gov (United States)

Song, Chang; Du, Liqun; Zhao, Wenjun; Zhu, Heqing; Zhao, Wen; Wang, Weitai

2018-04-01

Micro electroforming, as a mature micromachining technology, is widely used to fabricate metal microdevices in micro electro mechanical systems (MEMS). However, large residual stress in the local positions of the micro electroforming layer often leads to non-uniform residual stress distributions, dimension accuracy defects and reliability issues during fabrication of the metal microdevice. To solve this problem, a novel design method of presetting stress release geometries in the topological structure of the metal microstructure is proposed in this paper. First, the effect of stress release geometries (circular shape, annular groove shape and rivet shape) on the residual stress in the metal microstructure was investigated by finite element modeling (FEM) analysis. Two evaluation parameters, stress concentration factor K T and stress non-uniformity factor δ were calculated. The simulation results show that presetting stress release geometries can effectively reduce and homogenize the residual stress in the metal microstructures were measured metal microstructure. By combined use with stress release geometries of annular groove shape and rivet shape, the stress concentration factor K T and the stress non-uniformity factor δ both decreased at a maximum of 49% and 53%, respectively. Meanwhile, the average residual stress σ avg decreased at a maximum of 20% from  -292.4 MPa to  -232.6 MPa. Then, micro electroforming experiments were carried out corresponding to the simulation models. The residual stresses in the metal microstructures were measured by micro Raman spectroscopy (MRS) method. The results of the experiment proved that the stress non-uniformity factor δ and the average residual stress σ avg also decreased at a maximum with the combination use of annular groove shape and rivet shape stress release geometries, which is in agreement with the results of FEM analysis. The stress non-uniformity factor δ has a maximum decrease of 49% and the

Residual stress by repair welds

International Nuclear Information System (INIS)

Mochizuki, Masahito; Toyoda, Masao

2003-01-01

Residual stress by repair welds is computed using the thermal elastic-plastic analysis with phase-transformation effect. Coupling phenomena of temperature, microstructure, and stress-strain fields are simulated in the finite-element analysis. Weld bond of a plate butt-welded joint is gouged and then deposited by weld metal in repair process. Heat source is synchronously moved with the deposition of the finite-element as the weld deposition. Microstructure is considered by using CCT diagram and the transformation behavior in the repair weld is also simulated. The effects of initial stress, heat input, and weld length on residual stress distribution are studied from the organic results of numerical analysis. Initial residual stress before repair weld has no influence on the residual stress after repair treatment near weld metal, because the initial stress near weld metal releases due to high temperature of repair weld and then stress by repair weld regenerates. Heat input has an effect for residual stress distribution, for not its magnitude but distribution zone. Weld length should be considered reducing the magnitude of residual stress in the edge of weld bead; short bead induces high tensile residual stress. (author)

The adhesion strength and residual stress of colloidal-sol gel derived β-Tricalcium-Phosphate/Fluoridated-Hydroxyapatite biphasic coatings

International Nuclear Information System (INIS)

Cheng Kui; Zhang, Sam; Weng Wenjian; Khor, Khiam Aik; Miao Shundong; Wang Yongsheng

2008-01-01

β-tricalcium phosphate (β-TCP) powders are embedded in a fluoridated hydroxyapatite (FHA) matrix to form β-TCP-FHA composites via colloidal-sol gel method. This composite layer is deposited on top of a FHA layer to form a β-TCP-FHA/FHA biphasic coating. The effect of the nanosized powder on the residual stress is characterized through the X-ray diffraction peak shift. The powder incorporation increases the residual stress, while a large amount of β-TCP (Ca powder /Ca sol ratio is higher than 1/2) results in less gel shrinkage that partially compensates the mismatch of thermal expansion coefficient and thus the residual stress. Despite the elevated residual stress as more powders are embedded, the coating adhesion strength remains virtually constant: around 430 mN-500 mN in scanning scratch test

The effect of commercial processing procedures on {sup 14}C-carbendazim residues in soybean oil and tomato

Energy Technology Data Exchange (ETDEWEB)

Genyuan, Peng; Huaguo, Wang; Mengwen, Qi; Fujun, Wang; Changjiu, Zhou [Laboratory for the Application of Nuclear Techniques, Beijing Agricultural University, Beijing (China)

1994-06-01

Under simulated agricultural practices, soybean plants were treated with {sup 14}C-labelled carbendazim during the blooming stage. The residue in seeds was determined to be 0.067 ppm; corresponding to 0.076 ppm respectively. After subjecting the oil to degumming, alkali treatment, bleaching and deodorization, 53.7% of original radioactivity was removed. Deodorization was the most effect process, removing about 20% of the residue. The concentration of residues in the deodorized oil decreased about 30%. In soybean seed and cake, the residue was mainly present as carbendazim, the concentration of the other metabolites did not exceed 30% of the residue. Tomatoes grown on a field plot were treated with {sup 14}C-carbendazim. After harvest, the tomatoes were processed into tomato juice and canned whole fruit. The magnitude and nature of residues in samples taken at several processing steps were determined to evaluate the effect of commercial processing on removing or eliminating the residues. The results showed that the surface residues on tomato would be removed efficiently by simple washing of tomato. A buffer solution of phosphate had the highest efficiency. Tomato juice contained lower residues than canned whole fruit.

Embrittling effects of residual elements on steels

International Nuclear Information System (INIS)

Brear, J.M.; King, B.L.

1979-01-01

In a review of work related to reheat cracking in nuclear pressure vessel steels, Dhooge et al referred to work of the authors on the relative embrittling parameter for SA533B steels. The poor agreement when these parameters were applied to creep ductility data for SA508 class 2 lead the reviewers to conclude that the relative importance of impurity elements is a function of base alloy composition. The authors briefly describe some of their more recent work which demonstrates that when various mechanical, and other, effects are taken into consideration, the relative effects of the principal residual elements are similar, despite differing base compositions, and that the embrittling parameters derived correlate well with the data for SA Class 2 steel. (U.K.)

Effect of the weld groove shape and pass number on residual stresses in butt-welded pipes

International Nuclear Information System (INIS)

Sattari-Far, I.; Farahani, M.R.

2009-01-01

This study used finite element techniques to analyze the thermo-mechanical behaviour and residual stresses in butt-welded pipes. The residual stresses were also measured in some welds by using the Hole-Drilling method. The results of the finite element analysis were compared with experimentally measured data to evaluate the accuracy of the finite element modelling. Based on this study, a finite element modelling procedure with reasonable accuracy was developed. The developed FE modelling was used to study the effects of weld groove shape and weld pass number on welding residual stresses in butt-welded pipes. The hoop and axial residual stresses in pipe joints of 6 and 10 mm thickness of different groove shapes and pass number were studied. It is shown that these two parameters may have significant effects on magnitude and distribution of residual stresses in welded pipes.

Calcination/dissolution residue treatment

International Nuclear Information System (INIS)

Knight, R.C.; Creed, R.F.; Patello, G.K.; Hollenberg, G.W.; Buehler, M.F.; O'Rourke, S.M.; Visnapuu, A.; McLaughlin, D.F.

1994-09-01

Currently, high-level wastes are stored underground in steel-lined tanks at the Hanford site. Current plans call for the chemical pretreatment of these wastes before their immobilization in stable glass waste forms. One candidate pretreatment approach, calcination/dissolution, performs an alkaline fusion of the waste and creates a high-level/low-level partition based on the aqueous solubilities of the components of the product calcine. Literature and laboratory studies were conducted with the goal of finding a residue treatment technology that would decrease the quantity of high-level waste glass required following calcination/dissolution waste processing. Four elements, Fe, Ni, Bi, and U, postulated to be present in the high-level residue fraction were identified as being key to the quantity of high-level glass formed. Laboratory tests of the candidate technologies with simulant high-level residues showed reductive roasting followed by carbonyl volatilization to be successful in removing Fe, Ni, and Bi. Subsequent bench-scale tests on residues from calcination/dissolution processing of genuine Hanford Site tank waste showed Fe was separated with radioelement decontamination factors of 70 to 1,000 times with respect to total alpha activity. Thermodynamic analyses of the calcination of five typical Hanford Site tank waste compositions also were performed. The analyses showed sodium hydroxide to be the sole molten component in the waste calcine and emphasized the requirement for waste blending if fluid calcines are to be achieved. Other calcine phases identified in the thermodynamic analysis indicate the significant thermal reconstitution accomplished in calcination

Effect of preemptive weld overlay on residual stress of repaired weldment in surge nozzle

Energy Technology Data Exchange (ETDEWEB)

Oh, Chang Young; Song, Tae Kwang; Bae, Hong Yeol; Chun, Yun Bae; Kim, Yun Jae [Korea Univ., Seoul (Korea, Republic of); Lee, Kyoung Soo; Park, Chi Yong [Korea Electric Power Research Institute, Daejeon (Korea, Republic of)

2008-07-01

In the welding process, weldments usually include repair weld during the manufacturing process. Repair welds is supposed to cause strong tensile residual stress. Moreover weldments, usually made by Alloy 82/182, is susceptible to PWSCC. Therefore, mitigation of welding residual stress in weldments is important for reliable operating. PWOL is one of the methods for mitigation and verified for over twenty years. In this paper, residual stress distribution of repaired weldments and the effect of PWOL on mitigation is examined for surge nozzle.

Addition of an organic amendment and/or residue mud to bauxite residue sand in order to improve its properties as a growth medium.

Science.gov (United States)

Jones, B E H; Haynes, R J; Phillips, I R

2012-03-01

The effects of addition of carbonated residue mud (RMC) or seawater neutralized residue mud (RMS), at two rates, in the presence or absence of added green waste compost, on the chemical, physical and microbial properties of gypsum-treated bauxite residue sand were studied in a laboratory incubation study. The growth of two species commonly used in revegetation of residue sand (Lolium rigidum and Acacia saligna) in the treatments was then studied in a 18-week greenhouse study. Addition of green waste-based compost increased ammonium acetate-extractable (exchangeable) Mg, K and Na. Addition of residue mud at 5 and 10% w/w reduced exchangeable Ca but increased that of Mg and Na (and K for RMS). Concentrations of K, Na, Mg and level of EC in saturation paste extracts were increased by residue mud additions. Concentrations of cations in water extracts were considerably higher than those in saturation paste extracts but trends with treatment were broadly similar. Addition of both compost and residue mud caused a significant decrease in macroporosity with a concomitant increase in mesoporosity and microporosity, available water holding capacity and the quantity of water held at field capacity. Increasing rates of added residue mud reduced the percentage of sample present as discrete sand particles and increased that in aggregated form (particularly in the 1-2 and >10mm diameter ranges). Organic C content, C/N ratio, soluble organic C, microbial biomass C and basal respiration were increased by compost additions. Where compost was added, residue mud additions caused a substantial increase in microbial biomass and basal respiration. L. rigidum grew satisfactorily in all treatments although yields tended to be reduced by additions of mud (especially RMC) particularly in the absence of added compost. Growth of A. saligna was poor in sand alone and mud-amended sand and was greatly promoted by additions of compost. However, in the presence of compost, addition of carbonated

Effects of thermal residual stresses and fiber packing on deformation of metal-matrix composites

International Nuclear Information System (INIS)

Nakamura, T.; Suresh, S.

1993-01-01

The combined effects of thermal residual stresses and fiber spatial distribution on the deformation of a 6061 aluminum alloy containing a fixed concentration unidirectional boron fibers have been analyzed using detailed finite element models. The geometrical structure includes perfectly periodic, uniformly space fiber arrangements in square and hexagonal cells, as well as different cells in which either 30 or 60 fibers are randomly placed in the ductile matrix. The model involves an elastic-plastic matrix, elastic fibers, and mechanically bonded interfaces. The results indicate that both fiber packing and thermal residual stresses can have a significant effect on the stress-strain characteristics of the composite. The thermal residual stresses cause pronounced matrix yielding which also influences the apparent overall stiffness of the composite during the initial stages of subsequent far-field loading along the axial and transverse direction. Furthermore, the thermal residual stresses apparently elevate the flow stress of the composite during transverse tension. Such effects can be traced back to the level of constraint imposed on the matrix by local fiber spacing. The implications of the present results to the processing of the composites are also briefly addressed

Analysis of shot-peening and residual stress relaxation in the nickel-based superalloy RR1000

International Nuclear Information System (INIS)

Foss, B.J.; Gray, S.; Hardy, M.C.; Stekovic, S.; McPhail, D.S.; Shollock, B.A.

2013-01-01

This work assesses the residual stress relaxation of the nickel-based alloy RR1000 due to thermal exposure and dwell-fatigue loading. A number of different characterization methods, including X-ray residual stress analysis, electron back-scattered diffraction, microhardness testing and focused ion beam secondary electron imaging, contributed to a detailed study of the shot-peened region. Thermal exposure at 700 °C resulted in a large reduction in the residual stresses and work-hardening effects in the alloy, but the subsurface remained in a beneficial compressive state. Oxidizing environments caused recrystallization in the near surface, but did not affect the residual stress-relaxation behaviour. Dwell-fatigue loading caused the residual stresses to return to approximately zero at nearly all depths. This work forms part of an ongoing investigation to determine the effects of shot-peening in this alloy with the motivation to improve the fatigue and oxidation resistance at 700 °C

Interactive effects of rice residue and water stress on growth and metabolism of wheat seedlings

Directory of Open Access Journals (Sweden)

Nimisha Amist

2014-08-01

Full Text Available In the present study effects of rice residue with and without water stress were studied on Triticum aestivum L. cv. Shatabadi. The mixture of residue and garden soil in 1:1 ratio was considered as 50% (R1 and only decomposed residue as 100% (R2. Garden soil was taken as control. Twenty five seeds were sown in each experimental trays filled with soil mixture according to the treatments. Trays were arranged in two groups. After 15 days one set was subjected to water stress (WS by withholding water supply for 3 days. Morphological and biochemical parameters of 18 days old seedlings were recorded. Seedling height decreased in all treatments. A gradual decrease in relative water content, pigment and protein contents of wheat seedlings were observed. Sugar and proline contents increased in treatments. An increase in malondialdehyde (MDA content and antioxidative enzyme activities was recorded. Elevation in catalase activity was observed in all treatments except in plants with water deficit. Ascorbate peroxidase (APX and guaiacol peroxidase (GPX activities increased when residue mixed with soil but decreased in seedlings under the combined influence of the residue and water stress. Higher amount of MDA and lower activities of APX and GPX reflected the oxidative damage in seedlings under combined treatments. Rice residue inhibited growth of wheat seedlings. Water stress intensified the effects of residue.

Role of Hydrophobic/Aromatic Residues on the Stability of Double-Wall β-Sheet Structures Formed by a Triblock Peptide.

Science.gov (United States)

Ozgur, Beytullah; Sayar, Mehmet

2017-04-27

Bioinspired self-assembling peptides serve as powerful building blocks in the manufacturing of nanomaterials with tailored features. Because of their ease of synthesis, biocompatibility, and tunable activity, this emerging branch of biomolecules has become very popular. The triblock peptide architecture designed by the Hartgerink group is a versatile system that allows control over its assembly and has been shown to demonstrate tunable bioactivity. Three main forces, Coulomb repulsion, hydrogen bonding and hydrophobicity act together to guide the triblock peptides' assembly into one-dimensional objects and hydrogels. It was shown previously that both the nanofiber morphology (e.g., intersheet spacing, formation of antiparallel/parallel β-sheets) and hydrogel rheology strictly depend on the choice of the core residue where the triblock peptide fibers with aromatic cores in general form shorter fibers and yield poor hydrogels with respect to the ones with aliphatic cores. However, an elaborate understanding of the molecular reasons behind these changes remained unclear. In this study, by using carefully designed computer based free energy calculations, we analyzed the influence of the core residue on the formation of double-wall fibers and single-wall β-sheets. Our results demonstrate that the aromatic substitution impairs the fiber cores and this impairment is mainly associated with a reduced hydrophobic character of the aromatic side chains. Such weakening is most obvious in tryptophan containing peptides where the fiber core absorbs a significant amount of water. We also show that the ability of tyrosine to form side chain hydrogen bonds plays an indispensable role in the fiber stability. As opposed to the impairment of the fiber cores, single-wall β-sheets with aromatic faces become more stable compared to the ones with aliphatic faces suggesting that the choice of the core residue can also affect the underlying assembly mechanism. We also provide an in

Effects of residual aberrations explored on single-walled carbon nanotubes

International Nuclear Information System (INIS)

Biskupek, Johannes; Hartel, Peter; Haider, Maximilian; Kaiser, Ute

2012-01-01

The effects of geometric residual aberrations such as coma B 2 and two-fold astigmatism A 1 on the contrast in aberration corrected high resolution transmission electron microscopy (HRTEM) images are investigated on single-walled carbon nanotubes (SWNT). The individual aberrations are adjusted and set up manually using an imaging C S -corrector. We demonstrate how coma B 2 can be recognized by an experienced user directly in the image and how it blurs the contrast. Even with uncorrected (resolution limiting) spherical aberration C S the coma B 2 has to be considered and must be minimized. Limits for a tolerable coma are given. The experiments are confirmed by image simulations. -- Highlights: ► Individual effects of residual aberrations such as B 2 , A 1 , and C S are demonstrated. ► Experimental HRTEM and simulated images of carbon nanotubes are compared. ► A detection limit of 50 nm B 2 in a single HRTEM image is determined.

Gender effects in gaming research: a case for regression residuals?

Science.gov (United States)

Pfister, Roland

2011-10-01

Numerous recent studies have examined the impact of video gaming on various dependent variables, including the players' affective reactions, positive as well as detrimental cognitive effects, and real-world aggression. These target variables are typically analyzed as a function of game characteristics and player attributes-especially gender. However, findings on the uneven distribution of gaming experience between males and females, on the one hand, and the effect of gaming experience on several target variables, on the other hand, point at a possible confound when gaming experiments are analyzed with a standard analysis of variance. This study uses simulated data to exemplify analysis of regression residuals as a potentially beneficial data analysis strategy for such datasets. As the actual impact of gaming experience on each of the various dependent variables differs, the ultimate benefits of analysis of regression residuals entirely depend on the research question, but it offers a powerful statistical approach to video game research whenever gaming experience is a confounding factor.

Site-Mutation of Hydrophobic Core Residues Synchronically Poise Super Interleukin 2 for Signaling: Identifying Distant Structural Effects through Affordable Computations

Directory of Open Access Journals (Sweden)

Longcan Mei

2018-03-01

Full Text Available A superkine variant of interleukin-2 with six site mutations away from the binding interface developed from the yeast display technique has been previously characterized as undergoing a distal structure alteration which is responsible for its super-potency and provides an elegant case study with which to get insight about how to utilize allosteric effect to achieve desirable protein functions. By examining the dynamic network and the allosteric pathways related to those mutated residues using various computational approaches, we found that nanosecond time scale all-atom molecular dynamics simulations can identify the dynamic network as efficient as an ensemble algorithm. The differentiated pathways for the six core residues form a dynamic network that outlines the area of structure alteration. The results offer potentials of using affordable computing power to predict allosteric structure of mutants in knowledge-based mutagenesis.

Effect of cooking on14 C-tetrachlorvinphos residues in faba beans

International Nuclear Information System (INIS)

Farghaly, M.; Zayed, S.M.A.D.

1986-01-01

The effect of cooking on 14 C-tetrachlorvinphos in stored vicia faba beans was studied. The results indicated that over 50% of the dose originally present inside the grains (37 ppm), could be recovered in the aqueous extract of the cooked grains. Considerable portion of radioactivity (About 22%) was associated with the grains in a non-extractable from. Residues in cooked beans included, in addition to a small amount of the parent insecticide, desmethyl tetrachlorvinphos, mono methyl phosphate and dimethyl phosphate. The results obtained indicate that tetrachlorvinphos residues are not appreciably affected by cooking. 1 tab

Effect of industrial residue combinations on availability of elements

Energy Technology Data Exchange (ETDEWEB)

Brännvall, Evelina, E-mail: evelina.brannvall@ltu.se [Waste Science and Technology, Luleå University of Technology, 97187 Luleå (Sweden); Zamora, Carles Belmonte [Waste Science and Technology, Luleå University of Technology, 97187 Luleå (Sweden); Sjöblom, Rolf [Waste Science and Technology, Luleå University of Technology, 97187 Luleå (Sweden); Tekedo AB, Spinnarvägen 10, 611 37 Nyköping (Sweden); Kumpiene, Jurate [Waste Science and Technology, Luleå University of Technology, 97187 Luleå (Sweden)

2014-07-15

Highlights: • Beneficial combination of fly ash and biosolids. • Nutrient availability increase. • Potentially toxic element availability decrease. • Measured element availability was differed from the calculated leaching potential. - Abstract: Industrial residues, such as fly ashes and biosolids, contain elements (e.g., N, P, K, S, Ca and Zn) that make them a viable alternative for synthetic fertilizers in forestry and agriculture. However, the use of these materials is often limited due to the presence of potentially toxic substances. It is therefore necessary to assess and, when warranted, modify the chemical and physical form of these and similar waste materials before any advantages are taken of their beneficial properties. Biofuel fly ash, municipal solid waste incineration (MSWI) fly ash, biosolids, peat, peat residues and gypsum board waste were combined in various proportions, and this resulted in increased leaching of N, P, S, Cu and Mn, but decreased leaching of Ca, K, Mg, Cr, Fe, Ni, Zn, Al, As and Pb. Chemical fractionation revealed that elements Ca, K, Mg, S and Mn were predominantly exchangeable, while the rest of the elements were less mobile. Cadmium was mostly exchangeable in MSWI fly ash, but less mobile in biofuel fly ash mixtures. Recycling of MSWI fly ash in the mixtures with fertilizers is considerably less attractive, due to the high levels of salts and exchangeable Cd.

Turnover of grain legume N rhizodeposits and effect of rhizodeposition on the turnover of crop residues

DEFF Research Database (Denmark)

Mayer, J.; Buegger, F.; Jensen, E.S.

2004-01-01

The turnover of N derived from rhizodeposition of faba bean (Vicia faba L.), pea (Pisum sativum L.) and white lupin (Lupinus albus L.) and the effects of the rhizodeposition on the subsequent C and N turnover of its crop residues were investigated in an incubation experiment (168 days, 15 degrees....... In the experiment the turnover of C and N was compared in soils with and without previous growth of three legumes and with and without incorporation of crop residues. After 168 days, 21% (lupin), 26% (faba bean) and 27% (pea) of rhizodeposition N was mineralised in the treatments without crop residues. A smaller...... amount of 15-17% was present as microbial biomass and between 30 and 55% of mineralised rhizodeposition N was present as microbial residue pool, which consists of microbial exoenzymes, mucous substances and dead microbial biomass. The effect of rhizodeposition on the C and N turnover of crop residues...

Effects of waste content of glass waste forms on Savannah River high-level waste disposal costs

International Nuclear Information System (INIS)

McDonell, W.R.; Jantzen, C.M.

1985-01-01

Effects of the waste content of glass waste forms of Savannah River high-level waste disposal costs are evaluated by their impact on the number of waste canisters produced. Changes in waste content affect onsite Defense Waste Processing Facility (DWPF) costs as well as offsite shipping and repository emplacement charges. A nominal 1% increase over the 28 wt % waste loading of DWPF glass would reduce disposal costs by about $50 million for Savannah River wastes generated to the year 2000. Waste form modifications under current study include adjustments of glass frit content to compensate for added salt decontamination residues and increased sludge loadings in the DWPF glass. Projected cost reductions demonstrate significant incentives for continued optimization of the glass waste loadings. 13 refs., 3 figs., 3 tabs

Residues and duality for projective algebraic varieties

CERN Document Server

Kunz, Ernst; Dickenstein, Alicia

2008-01-01

This book, which grew out of lectures by E. Kunz for students with a background in algebra and algebraic geometry, develops local and global duality theory in the special case of (possibly singular) algebraic varieties over algebraically closed base fields. It describes duality and residue theorems in terms of K�hler differential forms and their residues. The properties of residues are introduced via local cohomology. Special emphasis is given to the relation between residues to classical results of algebraic geometry and their generalizations. The contribution by A. Dickenstein gives applications of residues and duality to polynomial solutions of constant coefficient partial differential equations and to problems in interpolation and ideal membership. D. A. Cox explains toric residues and relates them to the earlier text. The book is intended as an introduction to more advanced treatments and further applications of the subject, to which numerous bibliographical hints are given.

Optimization of heat-liberating batches for ash residue stabilization

International Nuclear Information System (INIS)

Karlina, O.K.; Varlackova, G.A.; Ojovan, M.I.; Tivansky, V.M.; Dmitriev, S.A.

1999-01-01

The ash residue obtained after incineration of solid radioactive waste is a dusting poly-dispersed powder like material that contains radioactive nuclides ( 137 Cs, 90 Sr, 239 Pu, hor ( ellipsis)). Specific radioactivity of the ash can be about 10 5 --10 7 Bq/kg. In order to dispose of the ash, residue shall be stabilized by producing a monolith material. The ash residue can be either vitrified or stabilized into a ceramic matrix. For this purpose the ash residue is mixed with fluxing agents followed by melting of obtained composition in the different type melters. As a rule this requires both significant energy consumption and complex melting equipment. A stabilization technology of ash residue was proposed recently by using heat liberating batches-compositions with redox properties. The ash residue is melted due to exothermic chemical reactions in the mixture with heat-liberating batch that occur with considerable release of heat. Stabilization method has three stages: (1) preparation of a mixture of heating batch and ash residue with or without glass forming batch (frit); (2) ignition and combustion of mixed composition; (3) cooling (quenching) of obtained vitreous material. Combustion of mixed composition occurs in the form of propagation of reacting wave. The heat released during exothermic chemical reactions provides melting of ash residue components and production of glass-like phase. The final product consists of a glass like matrix with embedded crystalline inclusions of infusible ash residue components

Efeito residual de sulfentrazone, isoxaflutole e oxyfluorfen em três solos Residual effect of sulfentrazone, isoxaflutole and oxyfluorfen in three soils

Directory of Open Access Journals (Sweden)

C.A.D Melo

2010-12-01

oxyfluorfen, que apresentou controle praticamente constante em todas as épocas avaliadas, e do sulfentrazone, que mostrou elevado efeito residual ao longo do período avaliado. As características inerentes a cada herbicida, bem como as diferenças nos teores de matéria orgânica e de textura entre os solos, influenciam na persistência do sulfentrazone, isoxaflutole e oxyfluorfen no solo. Maior efeito residual de oxyfluorfen foi observado no solo franco-arenoso e de isoxaflutole no solo argiloso com alto teor de matéria orgânica. Já o sulfentrazone apresentou elevado efeito residual nos três solos estudados.The physical and chemical properties of soils, as well as climatic conditions, influence the behavior of herbicides applied in pre-emergence. This work aimed to evaluate the residual effect of sulfentrazone, isoxaflutole and oxyfluorfen in three soils. The trial was conducted in a protected environment in a randomized block experimental design, with four replications. The treatments for each soil were arranged in a 3 x 5 factorial, being three herbicides and five sowing periods after herbicide application. Sulfentrazone, isoxaflutole and oxyfluorfen were applied at 0.5 kg ha-1, 0.72 kg ha-1 and 0.113 kg ha-1, respectively, on plastic pots with 250 mL volume, previously filled with the two clay texture soils and the sandy loam texture soil. Subsequently, the bioindicator species Sorghum bicolor was sown at 0, 15, 30, 45 and 60 days after application (DAA. A control with no herbicide treatment was sown at different times for each soil and used as a comparison in the evaluations. At 21 days after sowing in each season, intoxication and plant growth were evaluated by means of shoot dry mass. Sorghum plants in the clay soil with 9.0 dag kg-1 of organic matter (O.M., submitted to the application of isoxaflutole, sulfentrazone and oxyfluorfen, produced shoot dry mass over the control to 34, 20 and 40%, respectively, at 60 DAA. In the sandy loam soil, it was observed a high

A Thermodamage Strength Theoretical Model of Ceramic Materials Taking into Account the Effect of Residual Stress

Directory of Open Access Journals (Sweden)

Weiguo Li

2012-01-01

Full Text Available A thermodamage strength theoretical model taking into account the effect of residual stress was established and applied to each temperature phase based on the study of effects of various physical mechanisms on the fracture strength of ultrahigh-temperature ceramics. The effects of SiC particle size, crack size, and SiC particle volume fraction on strength corresponding to different temperatures were studied in detail. This study showed that when flaw size is not large, the bigger SiC particle size results in the greater effect of tensile residual stress in the matrix grains on strength reduction, and this prediction coincides with experimental results; and the residual stress and the combined effort of particle size and crack size play important roles in controlling material strength.

Soluble carbon in oxisol under the effect of organic residue rates

Directory of Open Access Journals (Sweden)

Gabriela Lúcia Pinheiro

2014-06-01

Full Text Available The application of organic residues to the soil can increase soluble organic carbon (SOC and affect the pH and electrolytic conductivity (EC of the soil. However, the magnitude of these changes depends on the type of residue and the applied dose. This study aimed to evaluate the effect of increasing C rates contained in organic residue on the pH, EC, water-extractable total carbon (WETC, water-extractable organic carbon (WEOC, and water-extractable inorganic carbon (WEIC in soil treated with manure (chicken, swine, and quail, sawdust, coffee husk, and sewage sludge. The levels of total C (TC- KH2PO4, organic carbon (OC- KH2PO4, and inorganic C (IC- KH2PO4 extractable by a 0.1 mol L-1 KH2PO4 solution were also quantified in soil under the effect of increasing rates of chicken and quail manures. The following rates of organic residue C were applied to a dystrophic Red Latosol (Oxisol sample: 0, 2,000, 5,000, 10,000, and 20,000 mg kg-1. The addition of organic residues to the soil increased pH, except in the case of sewage sludge, which acidified the soil. The acidity correction potential of chicken and quail manure was highest, dependent on the manure rate applied; regardless of the dose used, sawdust barely alters the soil pH. At all tested rates, the EC of the soil treated with swine manure, coffee husk, and sawdust remained below 2.0 dS m-1, which is a critical level for salinity-sensitive crops. However, the application of chicken or quail manure and sewage sludge at certain rates increased the EC to values above this threshold level. Highest levels of WETC, WEOC, and WEIC were obtained when chicken and quail manure and coffee husk were applied to the Oxisol. The quantities of SOC extracted by KH2PO4 were higher than the quantities extracted by water, demonstrating the ability of soil to adsorb C into its colloids.

Irradiation and modified atmosphere packaging effects on residual nitrite, ascorbic acid, nitrosomyoglobin, and color in sausage.

Science.gov (United States)

Ahn, Hyun-Joo; Jo, Cheorun; Lee, Ju-Woon; Kim, Jae-Hyun; Kim, Kee-Hyuk; Byun, Myung-Woo

2003-02-26

The present study was undertaken to evaluate the irradiation and modified atmosphere packaging effects on emulsion-type cooked pork sausage during storage for 4 weeks. CO(2) (100%), N(2) (100%), or 25% CO(2)/75% N(2) packaged sausage were irradiated at 0, 5, and 10 kGy, and residual nitrite, residual ascorbic acid, nitrosomyoglobin (NO-Mb), color values, and their correlation were observed. Irradiation significantly reduced the residual nitrite content and caused partial reduction of NO-Mb during storage. No difference was observed in ascorbic acid content by irradiation. Irradiation decreased the Hunter color a value of sausage. CO(2) or CO(2)/N(2) packaging were more effective for reducing residual nitrite and inhibiting the loss of the red color of sausage compared to N(2) packaging. Results indicated that the proper combination of irradiation and modified atmosphere packaging could reduce the residual nitrite in sausage with minimization of color change.

Sub-lethal effects of pesticide residues in brood comb on worker honey bee (Apis mellifera development and longevity.

Directory of Open Access Journals (Sweden)

Judy Y Wu

Full Text Available BACKGROUND: Numerous surveys reveal high levels of pesticide residue contamination in honey bee comb. We conducted studies to examine possible direct and indirect effects of pesticide exposure from contaminated brood comb on developing worker bees and adult worker lifespan. METHODOLOGY/PRINCIPAL FINDINGS: Worker bees were reared in brood comb containing high levels of known pesticide residues (treatment or in relatively uncontaminated brood comb (control. Delayed development was observed in bees reared in treatment combs containing high levels of pesticides particularly in the early stages (day 4 and 8 of worker bee development. Adult longevity was reduced by 4 days in bees exposed to pesticide residues in contaminated brood comb during development. Pesticide residue migration from comb containing high pesticide residues caused contamination of control comb after multiple brood cycles and provided insight on how quickly residues move through wax. Higher brood mortality and delayed adult emergence occurred after multiple brood cycles in contaminated control combs. In contrast, survivability increased in bees reared in treatment comb after multiple brood cycles when pesticide residues had been reduced in treatment combs due to residue migration into uncontaminated control combs, supporting comb replacement efforts. Chemical analysis after the experiment confirmed the migration of pesticide residues from treatment combs into previously uncontaminated control comb. CONCLUSIONS/SIGNIFICANCE: This study is the first to demonstrate sub-lethal effects on worker honey bees from pesticide residue exposure from contaminated brood comb. Sub-lethal effects, including delayed larval development and adult emergence or shortened adult longevity, can have indirect effects on the colony such as premature shifts in hive roles and foraging activity. In addition, longer development time for bees may provide a reproductive advantage for parasitic Varroa destructor

The Effect of Stochastically Varying Creep Parameters on Residual Stresses in Ceramic Matrix Composites

Science.gov (United States)

Pineda, Evan J.; Mital, Subodh K.; Bednarcyk, Brett A.; Arnold, Steven M.

2015-01-01

Constituent properties, along with volume fraction, have a first order effect on the microscale fields within a composite material and influence the macroscopic response. Therefore, there is a need to assess the significance of stochastic variation in the constituent properties of composites at the higher scales. The effect of variability in the parameters controlling the time-dependent behavior, in a unidirectional SCS-6 SiC fiber-reinforced RBSN matrix composite lamina, on the residual stresses induced during processing is investigated numerically. The generalized method of cells micromechanics theory is utilized to model the ceramic matrix composite lamina using a repeating unit cell. The primary creep phases of the constituents are approximated using a Norton-Bailey, steady state, power law creep model. The effect of residual stresses on the proportional limit stress and strain to failure of the composite is demonstrated. Monte Carlo simulations were conducted using a normal distribution for the power law parameters and the resulting residual stress distributions were predicted.

Responses of Pea (Pisum sativum Growth and Yield to Residual Effects of Organic and Urea Fertilizers from Previous Crop

Directory of Open Access Journals (Sweden)

S. Fallah

2016-07-01

Full Text Available Application of organic manure in organic farming and long-term mineralization may lead to residual effects on the succeeding crop. So, residual effects of combined cattle manure and urea fertilizer of previous crop (black cumin on growth and yield of pea were examined in a randomized complete block design. Treatments included of  cattle manure (CM, urea (U, three ratios of CM+U full dose application (2:1; 1:1; 1:2 and three ratios of CM+U split application (2:1; 1:1; 1:2, and unfertilized control to previous crop (black cumin in 2012. Pea planted without any fertilizer in 2013. There was no significant difference between control and residual of urea treatment for some parameters including dry matter in flowering stage, plant nitrogen and phosphorus concentration, plant height, yield components, grain yield and biological yield of pea. Biological and grain yields were greater under both residual of cattle manure treatment and integrated treatments compared to residual of urea treatment. The highest grain yield (4000 kg ha-1 was observed in residual of CM:U full dosed application treatment, to the extent that grain yield in this treatment indicated a 1.5-fold increase in comparison with residual of urea treatment. The highest biological yield (8325 kg ha-1 was obtained in residual of CM treatment, though it was not significant different from that of residual of CM:U (1:2 treatments. In general, although residual of urea fertilizer did not leave a notable effect on pea production, but production of this crop relying on residual of cattle manure deems effective to lowering of fertilization cost and ameliorating environmental contaminations.

Process solutions for reducing PR residue over non-planar wafer

Science.gov (United States)

Lin, C. H.; Huang, C. H.; Yang, Elvis; Yang, T. H.; Chen, K. C.; Lu, Chih-Yuan

2011-03-01

SAS (Self-Aligned Source) process has been widely adopted on manufacturing NOR Flash devices. To form the SAS structure, the compromise between small space patterning and sufficiently removing photo resist residue in topographical substrate has been a critical challenge as the device scaling down. In this study, photo simulation, layout optimization, resist processing and tri-layer materials were evaluated to form defect-free and highly extendible SAS structure for NOR Flash devices. Photo simulation suggested more coherent light source allowed the incident light to reach the trench bottom that facilitates the removal of photo resist. Mask bias also benefited the process latitude extension for residue-free SAS printing. In the photo resist processing, both lowering the SB (Soft Bake) and raising PEB (Post-Exposure Bake) temperature of photo resist were helpful to broaden the process window but the final pattern profile was not good enough. Thermal flow for pos-exposure pattern shrinkage achieved small CD (Critical Dimension) patterning with residue-free, however the materials loading effect is another issue to be addressed at memory array boundary. Tri-layer scheme demonstrated good results in terms of free from residue, better substrate reflectivity control, enabling smaller space printing to loosen overlay specification and minimizing the poly gate clipping defect. It was finally proposed to combine with etch effort to from the SAS structure. Besides it is also promising to extend to even smaller technology nodes.

Residual stress effects on the impact resistance and strength of fiber composites

Science.gov (United States)

Chamis, C. C.

1973-01-01

Equations have been derived to predict degradation effects of microresidual stresses on impact resistance of unidirectional fiber composites. Equations also predict lamination residual stresses in multilayered angle ply composites.

The role and effect of residual stress on pore generation during anodization of aluminium thin films

International Nuclear Information System (INIS)

Liao, M.W.; Chung, C.K.

2013-01-01

Highlights: •Al films of varying residual stress were prepared by sputtering. •Variation of the residual stress in the Al films influences pore growth during anodization. •The change in average pore size with residual stress is fairly small. •Interaction of residual stress with oxide growth stress leads to change in structure. •Residual tensile stress increases the pore density of porous alumina. -- Abstract: The role and effect of residual stress on pore generation of anodized aluminium oxide (AAO) have been investigated into anodizing the various-residual-stresses aluminium films. The plane stresses were characterised by X-ray diffraction with sin 2 ψ method. The pore density roughly linearly increased with residual stress from 64.6 (−132.5 MPa) to 90.5 pores/μm 2 (135.9 MPa). However, the average pore size around 40 nm was not changed significantly except for the rougher film. The tensile residual stress lessened the compressive oxide growth stress to reduce AAO plastic deformation for higher pore density. The findings provide new foundations for realizing AAO films on silicon

Effects of residual stress on fatigue strength of small diameter welded pipe joint

International Nuclear Information System (INIS)

Yamashita, Tetsuo; Hattori, Takahiro; Nomoto, Toshiharu; Iida, Kunihiro; Sato, Masanobu

1996-01-01

A power plant consists of many welded components, therefore, it is essential in establishing the reliability of the power plant to maintain the reliability of all welded components. The fatigue failure caused by mechanical vibrations of small diameter welded joints, which is represented by socket welded joints, is one of the major causes of trouble for the welded parts of the power plant. Here, bending fatigue tests were conducted to investigate the fatigue strength of small diameter socket welded pipe joints. In the most cases of large diameter socket joints, a fatigue crack started from the root of the fillet weld though the stress amplitude at the root was smaller than that at the toe of fillet weld. Additionally, the fatigue strength was affected by the weld bead sequence. The residual stress was considered to be one of the important parameters governing fatigue strength, therefore, its effects were investigated. In several types of pipe joints, the local stress and residual stress distributions were calculated by finite element analysis. The residual stresses were compressive at the toe and tensile at the root of the socket welded joints. Based on these results, the effects of residual stresses on the fatigue strength are discussed for small diameter welded pipe joints in the present work

Stabilization of plutonium bearing residues at Lawrence Livermore National Laboratory

International Nuclear Information System (INIS)

Bronson, M.C.; Van Konynenburg, R.A.; Ebbinghaus, B.B.

1995-01-01

The US Department of Energy's (US DOE) Lawrence Livermore National Laboratory (LLNL) has plutonium holdings including metal, oxide and residue materials, all of which need stabilization of some type. Residue materials include calcined ash, calcined precipitates, pyrochemical salts, glove box sweepings, metallurgical samples, graphite, and pyrochemical ceramic crucibles. These residues are typical of residues stored throughout the US DOE plutonium sites. The stabilization process selected for each of these residues requires data on chemical impurities, physical attributes, and chemical forms of the plutonium. This paper outlines the characterization and stabilization of LLNL ash residues, pyrochemical salts, and graphite

Effect of residual nitrogen and fertilizer nitrogen on sugar beet production in Finland

Directory of Open Access Journals (Sweden)

Veikko Brummer

1974-09-01

Full Text Available Preliminary determinations for NO3- and NH4-N in topsoil from nitrogen field experiments are discussed. The amounts of residual nitrogen as well as the dates and depth for sampling are considerd in order to investigate the need of fertilizer-N for continuous sugar beet. Tops ploughed down as manure increased the available soil nitrogen by about 50 kg/ha. In practice nitrogen from fertilizer and farmyard manure given to previous beet crops seems to accumulate in the beet soils of Finland. The concentrations of nitrate and ammonium nitrogen in topsoil were low in the spring of 1972 and 1973. NO3-N increased in topsoil during the early summer, and the highest concentrations were found at the beginning of July. Starting from the middle of July the amount of NH4-N began to increase both in topsoil and in subsoil. With increasing amounts of nitrogen in the topsoil the sugar content decreases continuously. Also the α-amio N content of beets correlates with the soil nitrogen. There is experimental evidence that 150 180 kg/ha nitrate nitrogen in topsoil (residual + fertilizer N in early July gives the best economic result. The effects of fertilizer and accumulated soil nitrogen on the sugar beet quality together with som other experimental data have been statistically analysed. Regression coefficients indicated that both forms of nitrogen affected the suger content, the α-amino N concentration and clear juice purity, in a similar way.

Enhanced coagulation for improving coagulation performance and reducing residual aluminum combining polyaluminum chloride with diatomite.

Science.gov (United States)

Hu, Wenchao; Wu, Chunde

2016-01-01

The feasibility of using enhanced coagulation, which combined polyaluminum chloride (PAC) with diatomite for improving coagulation performance and reducing the residual aluminum (Al), was discussed. The effects of PAC and diatomite dosage on the coagulation performance and residual Al were mainly investigated. Results demonstrated that the removal efficiencies of turbidity, dissolved organic carbon (DOC), and UV254 were significantly improved by the enhanced coagulation, compared with PAC coagulation alone. Meaningfully, the five forms of residual Al (total Al (TAl), total dissolved Al (TDAl), dissolved organic Al (DOAl), dissolved monomeric Al (DMAl), and dissolved organic monomeric Al (DOMAl)) all had different degrees of reduction in the presence of diatomite and achieved the lowest concentrations (0.185, 0.06, 0.053, 0.014, and 0 mg L(-1), respectively) at a PAC dose of 15 mg L(-1) and diatomite dose of 40 mg L(-1). In addition, when PAC was used as coagulant, the majority of residual Al existed in dissolved form (about 31.14-70.16%), and the content of DOMAl was small in the DMAl.

Predictive models of forest logging residues of Triplochiton ...

African Journals Online (AJOL)

The model developed indicated that logarithmic functions performed better than other form of equation. The findings of this study revealed that there is significant logging residues left to waste in the forest after timber harvest and quantifying this logging residue in terms of biomass model can serve as management tools in ...

Effect of residual stress on the integrity of a branch connection

International Nuclear Information System (INIS)

Law, M.; Kirstein, O.; Luzin, V.

2012-01-01

A new connection to an existing gas pipeline was made by hot-tapping, welding directly onto a pressurised pipeline. The welds were not post-weld heat treated, causing significant residual stresses. The critical weld had residual stresses determined by neutron diffraction using ANSTO's residual stress diffractometer, Kowari. The maximum measured residual stress (290 MPa) was 60% of the yield strength. The magnitudes of errors from a number of sources were estimated. An integrity assessment of the welded branch connection was performed with the measured residual stress values and with residual stress distributions from the BS 7910 and API 579 analysis codes. Analysis using estimates of residual stress from API 579 overestimated the critical crack size. Highlights: ► Residual stresses were measured by neutron diffraction in a thick section, non post-weld heat treated ferritic weld. ► There is little published data on these welds. ► The work compares the measured residual stresses with code-based residual stress distributions.

Relation between psi-splitting and microscopic residual shear stresses in x-ray stress measurement on uni-directionally deformed layers

International Nuclear Information System (INIS)

Hanabusa, Takao; Fujiwara, Haruo

1982-01-01

The psi-splitting behaviors were investigated for the ground and the milled surface layers of both iron and high speed steel in order to find out the relation among microscopic residual shear stresses. For the high speed steel, the X-ray elastic constants and the residual strains were measured on the carbide phase as well as on the matrix phase. It was clarified that the psi-splitting was caused by a combination of the selective nature of X-ray diffractions and the microscopic residual shear stresses within the interior of cells and the carbide particles. The volume fraction occupied by the cell walls and the residual shear stresses sustained by them were estimated from the equilibrium condition of the microscopic residual shear stresses. The distributions of residual stresses over the deformed layers indicate that the thermal effect is dominant in grinding and the mechanical effect is dominant in milling for forming residual stresses. (author)

Intermolecular Modes between LH2 Bacteriochlorophylls and Protein Residues: The Effect on the Excitation Energies.

Science.gov (United States)

Anda, André; De Vico, Luca; Hansen, Thorsten

2017-06-08

Light-harvesting system 2 (LH2) executes the primary processes of photosynthesis in purple bacteria; photon absorption, and energy transportation to the reaction center. A detailed mechanistic insight into these operations is obscured by the complexity of the light-harvesting systems, particularly by the chromophore-environment interaction. In this work, we focus on the effects of the protein residues that are ligated to the bacteriochlorophylls (BChls) and construct potential energy surfaces of the ground and first optically excited state for the various BChl-residue systems where we in each case consider two degrees of freedom in the intermolecular region. We find that the excitation energies are only slightly affected by the considered modes. In addition, we see that axial ligands and hydrogen-bonded residues have opposite effects on both excitation energies and oscillator strengths by comparing to the isolated BChls. Our results indicate that only a small part of the chromophore-environment interaction can be associated with the intermolecular region between a BChl and an adjacent residue, but that it may be possible to selectively raise or lower the excitation energy at the axial and planar residue positions, respectively.

Effect of constraint condition and internal medium on residual stress under overlay welding for dissimilar metal welding

International Nuclear Information System (INIS)

Song, Tae Kwang; Kim, Yun Jae; Lee, Kyoung Soo; Park, Chi Yong; Kim, Jong Sung; Kim, Jin Weon

2007-01-01

In nuclear power plants, residual stress of dissimilar metal weld propagates cracks in the weld metal which is susceptible to stress corrosion cracking. Overlay welding is a process widely used to mitigate residual stress replacing inside tensile stress by compression stress. However, according to the result of this study the effect of overlay welding on residual stress depends on both internal medium and constraint condition. The purpose of this study is to maximize the positive effect of overlay welding by finite element analyses

Modelling of the Residual Stress State in a new Type of Residual Stress Specimen

DEFF Research Database (Denmark)

Jakobsen, Johnny; Andreasen, Jens Henrik

2014-01-01

forms the experimental case which is analysed. A FE model of the specimen is used for analysing the curing history and the residual stress build up. The model is validated against experimental strain data which are recorded by a Fibre Brag Grating sensor and good agreement has been achieved.......The paper presents a study on a new type residual stress specimen which is proposed as a simple way to conduct experimental validation for model predictions. A specimen comprising of a steel plate with circular hole embedded into a stack of CSM glass fibre and further infused with an epoxy resin...

Effect of cooking on residues of the quinolones oxolinic acid and flumequine in fish.

Science.gov (United States)

Steffenak, I; Hormazabal, V; Yndestad, M

1994-01-01

The effect of cooking on residues of the quinolones oxolinic acid and flumequine in fish was investigated. Salmon containing residues of oxolinic acid and flumequine was boiled or baked in the oven. Samples of raw and cooked muscle, skin, and bone, as well as of the water in which the fish was boiled and juice from the baked fish, were analysed. Oxolinic acid and flumequine did not degrade at the temperatures reached when cooking the fish. However, fish muscle free from drug residues may be contaminated during boiling and baking due to leakage of the drug from reservoirs in the fish.

Reclamation of Herb Residues Using Probiotics and Their Therapeutic Effect on Diarrhea

Directory of Open Access Journals (Sweden)

Fanjing Meng

2017-01-01

Full Text Available Residues from herbal medicine processing in pharmaceutical plants create a large amount of waste (herb residues, which consists mainly of environmental pollution and medicinal waste. In order to resolve this problem, probiotics of Bacillus (B. subtilis, Aspergillus (A. oryzae, and Lactobacillus (L. plantarum M3 are selected to reuse herb residue of Jianweixiaoshi tablets (JT, and an antibiotic-associated diarrhea (AAD mouse model was established to evaluate the therapeutic effects of the herb residue fermentation supernatant. Our results indicated that the fermentation supernatant had scavenged 77.8% of 2,2-diphenyl-1-picrylhydrazyl (DPPH, 78% of O2•−, 36.7% of •OH, 39% of Fe2+ chelation, and 716 mg/L reducing power. The inhibition zones for Salmonella (S. typhimurium, S. enteritidis, Shigella (Sh. flexneri, Escherichia (E. coli, Listeria (L. monocytogenes, Sh. dysenteriae 301, and Staphylococcus (S. aureus were 17, 14, 19, 18, 20, 19, and 20 mm, respectively. The in vivo results indicated that the fermentation supernatant resulted in a high diarrhea inhibition rate (56%, p<0.05, greatly enhanced the disruption of bacterial diversity caused by antibiotics, and restored the dominant position of L. johnsonii in the treatment and recovery stages. Therefore, the combination of the herb residue and probiotics suggests a potential to explore conversion of these materials for the possible development of therapies for AAD.

The influence of quench sensitivity on residual stresses in the aluminium alloys 7010 and 7075

International Nuclear Information System (INIS)

Robinson, J.S.; Tanner, D.A.; Truman, C.E.; Paradowska, A.M.; Wimpory, R.C.

2012-01-01

The most critical stage in the heat treatment of high strength aluminium alloys is the rapid cooling necessary to form a supersaturated solid solution. A disadvantage of quenching is that the thermal gradients can be sufficient to cause inhomogeneous plastic deformation which in turn leads to the development of large residual stresses. Two 215 mm thick rectilinear forgings have been made from 7000 series alloys with widely different quench sensitivity to determine if solute loss in the form of precipitation during quenching can significantly affect residual stress magnitudes. The forgings were heat treated and immersion quenched using cold water to produce large magnitude residual stresses. The through thickness residual stresses were measured by neutron diffraction and incremental deep hole drilling. The distribution of residual stresses was found to be similar for both alloys varying from highly triaxial and tensile in the interior, to a state of biaxial compression in the surface. The 7010 forging exhibited larger tensile stresses in the interior. The microstructural variation from surface to centre for both forgings was determined using optical and transmission electron microscopy. These observations were used to confirm the origin of the hardness variation measured through the forging thickness. When the microstructural changes were accounted for in the through thickness lattice parameter, the residual stresses in the two forgings were found to be very similar. Solute loss in the 7075 forging appeared to have no significant effect on the residual stress magnitudes when compared to 7010. - Highlights: ► Through thickness residual stress measurements made on large Al alloy forgings. ► Residual stress characterised using neutron diffraction and deep hole drilling. ► Biaxial compressive surface and triaxial subsurface residual stresses. ► Quench sensitivity of 7075 promotes significant microstructural differences to 7010. ► When precipitation is

Effect of processing conditions on residual stress distributions by bead-on-plate welding after surface machining

International Nuclear Information System (INIS)

Ihara, Ryohei; Mochizuki, Masahito

2014-01-01

Residual stress is important factor for stress corrosion cracking (SCC) that has been observed near the welded zone in nuclear power plants. Especially, surface residual stress is significant for SCC initiation. In the joining processes of pipes, butt welding is conducted after surface machining. Residual stress is generated by both processes, and residual stress distribution due to surface machining is varied by the subsequent butt welding. In previous paper, authors reported that residual stress distribution generated by bead on plate welding after surface machining has a local maximum residual stress near the weld metal. The local maximum residual stress shows approximately 900 MPa that exceeds the stress threshold for SCC initiation. Therefore, for the safety improvement of nuclear power plants, a study on the local maximum residual stress is important. In this study, the effect of surface machining and welding conditions on residual stress distribution generated by welding after surface machining was investigated. Surface machining using lathe machine and bead on plate welding with tungsten inert gas (TIG) arc under various conditions were conducted for plate specimens made of SUS316L. Then, residual stress distributions were measured by X-ray diffraction method (XRD). As a result, residual stress distributions have the local maximum residual stress near the weld metal in all specimens. The values of the local maximum residual stresses are almost the same. The location of the local maximum residual stress is varied by welding condition. It could be consider that the local maximum residual stress is generated by same generation mechanism as welding residual stress in surface machined layer that has high yield stress. (author)

Efeito residual de herbicidas aplicados em pré-emergência em diferentes solos Residual effect of herbicides applied in pre-emergence in different soils

Directory of Open Access Journals (Sweden)

M.H. Inoue

2011-06-01

Full Text Available O objetivo deste trabalho foi monitorar o efeito residual dos herbicidas ametryne, clomazone e diuron, aplicados em pré-emergência, utilizando amostras de um Neossolo Quartzarênico e de um Latossolo Vermelho, com texturas e composições contrastantes. Para isso, foram conduzidos seis bioensaios em casa de vegetação, com amostras de um Neossolo Quartzarênico (textura arenosa e de um Latossolo Vermelho (textura argilosa. Foi avaliado o efeito residual de ametryne (0, 1,60 e 2,40 kg ha-1, clomazone (0, 0,90 e 1,10 kg ha-1 e diuron (0, 1,60 e 3,20 kg ha-1, por meio de semeadura de bioindicador previamente selecionado (Cucumis sativus ou Brachiaria decumbens aos 0, 25, 50, 75 e 100 dias após a aplicação (DAA. Verificou-se que ametryne proporcionou 80% de controle até os 40 DAA, independentemente do solo e da dose. O clomazone apresentou efeito residual satisfatório quando aplicado na dose recomendada em solo argiloso, mantendo o controle acima de 80% até os 71 DAA. Em solo arenoso, o controle não foi satisfatório já aos 25 DAA, mesmo na dose recomendada para solo argiloso. Diuron apresentou alta estabilidade em solo argiloso, observando-se controle superior a 91% até os 100 DAA na dose recomendada e controle acima de 80% até os 54 DAA na dose recomendada para solo arenoso. No entanto, em solo arenoso não houve aumento do efeito residual, mesmo com a aplicação da dose recomendada para solo argiloso.The objective of this work was to monitor the residual effect of the herbicides ametryne, clomazone and diuron, applied in pre-emergence, using Psament and Red Latosol with contrasting texture and composition. Thus, six experiments were conducted under greenhouse conditions with samples of Psament (sandy texture and Red Latosol (clay texture. The residual effect of ametryne (0, 1.60 and 2.40 kg ha-1, clomazone (0, 0.90 and 1.10 kg ha-1 and diuron (0, 1.60 and 3.20 kg ha 1 was evaluated by sowing the test plant (Cucumis sativus or

Reliability assessment of underground pipelines under the combined effect of active corrosion and residual stress

International Nuclear Information System (INIS)

Amirat, A.; Mohamed-Chateauneuf, A.; Chaoui, K.

2006-01-01

Lifetime management of underground pipelines is mandatory for safe hydrocarbon transmission and distribution systems. Reliability analysis is recognized as a powerful decision-making tool for risk-based design and maintenance. Both the residual stresses generated during the manufacturing process and in-service corrosion reduce the ability to resist internal and external loading. In this study, the residual stress distribution in large diameter pipes has been characterized experimentally in order to be coupled with the corrosion model. During the pipe lifetime, residual stress relaxation occurs due to the loss of pipe thickness as material layers are consumed by corrosion. The reliability-based assessment of residual stress effects is applied to underground pipelines under a roadway, with and without active corrosion. It has been found that the residual stress greatly increases the failure probability, especially in the early stage of the pipe lifetime

Effects of Adopting Different Kinds of Collecting Method for Years on Film Residual Coefficient and Maize Yields

Directory of Open Access Journals (Sweden)

TANG Wen-xue

2017-03-01

Full Text Available Wide usage of mulching technology has increased crop yields, but the large amounts of mulching film residue resulting from widespread use of plastic film in China has brought about a series of pollution hazards. Based on a 4-year (2011-2014 long-term experiment, the effects of different kinds of collecting mothod (zero plastic film residues, conventional plastic film residues, whole plastic film residues remainded on plastic film residues, residual coefficient and maize yield were explored. Plastic film residues mainly remained in 0~10 cm, 10~20 cm soil layers. In 0~30 cm soil layers, the two types of mulch residues (>25 cm2, 4~25 cm2 under zero plastic film residues treatment were much less than conventional plastic film residues and whole plastic film residues remainded treatments, no significant differences were observed in the mulch residues (2 among 3 treatments. After maize harvest, the amount of plastic film residues under zero plastic film residues, conventional plastic film residues and whole plastic film residues remainded treatments were 52.71, 80.85 kg·hm-2 and 152.65 kg·hm-2, respectively, the residual coefficient for zero plastic film residues, conventional plastic film residues and whole plastic film residues remainded treatments were -9.45%, 8.53% and 54.42%, respectively. The stem diameter, ear length, ear width, ear row number, grain number per row and 100-grain weight of maize decreased with the increase of residual film amount. Compared with the conventional plastic film residues, the mean grain yield of whole plastic film residues remainded treatment decreased by 15.08%, whereas the zero plastic film residues treatment increased by 4.70%. The plastic film residues, residual coefficient and maize yield were comprehensively analyzed, the conventional plastic film residues practice should be adopted currently without appropriate plastic film residues collector. But from the long-term development, we should speed up the

Effects of Diatomite Organic Fertilizer on Cd and Zn Forms and Availability of Cd-Zn Polluted Soil

Directory of Open Access Journals (Sweden)

LIN Ji

2014-08-01

Full Text Available An indoor soil cultivation experiment was carried out to study the effects of diatomite organic fertilizer on the forms and the avail-ability of Cd, Zn in soil. The results showed that the soil pH increased, the soil available Cd and Zn reduced after diatomite organic fertilizer application in contaminated soil. Diatomite organic fertilizer application decreased the contents of exchangeable form and weakly-bound-to organic form of Cd and Zn significantly, but increased the contents of strongly-bound-to organic form and residual form of Cd and Zn in con-taminated soil. Statistics analysis showed that the contents of exchangeable and weakly-bound-to organic form of Cd and Zn had highly sig-nificant relation to the content of soil available Cd and Zn(P<0.01. The contents of Mn oxide-occluded Cd had significant relation to the con-tent of soil available Cd(P<0.05. Comparing the treatments of diatomite organic fertilizer with the rate of 5%and 10%soil weight, there was no significant difference in soil pH, the contents of soil available Cd, Zn and the forms of Cd, Zn.

Effectiveness of dynamic MRI for diagnosing pericicatricial minimal residual breast cancer following excisional biopsy

International Nuclear Information System (INIS)

Kawashima, Hiroko; Tawara, Mari; Suzuki, Masayuki; Matsui, Osamu; Kadoya, Masumi

2001-01-01

The purpose of this study was to investigate the effectiveness of dynamic MRI for diagnosing pericicatricial minimal residual breast cancer following excisional biopsy. Twenty-six patients who underwent excisional biopsy of a tumor or calcified lesion of the breast underwent gadolinium-enhanced dynamic MRI by the fat-saturated 2D fast spoiled gradient echo (SPGR) sequence (group 1), 24 patients by the spectral IR enhanced 3D fast gradient echo (Efgre3d) sequence (group 2). Pericicatricial residual cancer was confirmed histologically in 29 of the 50 patients. The overall sensitivity, specificity, accuracy, positive predictive value, and negative predictive value of MRI for residual cancer diagnosis was 66, 81, 72, 83 and 63%. A nodular, thick and discontinuous enhanced rim around the scar is indicative of a residual tumor. However, false-positive findings due to granulation or proliferative fibrocystic change remain limitations

Effectiveness of dynamic MRI for diagnosing pericicatricial minimal residual breast cancer following excisional biopsy

Energy Technology Data Exchange (ETDEWEB)

Kawashima, Hiroko E-mail: hirokok@med.kanazawa-u.ac.jp; Tawara, Mari; Suzuki, Masayuki; Matsui, Osamu; Kadoya, Masumi

2001-10-01

The purpose of this study was to investigate the effectiveness of dynamic MRI for diagnosing pericicatricial minimal residual breast cancer following excisional biopsy. Twenty-six patients who underwent excisional biopsy of a tumor or calcified lesion of the breast underwent gadolinium-enhanced dynamic MRI by the fat-saturated 2D fast spoiled gradient echo (SPGR) sequence (group 1), 24 patients by the spectral IR enhanced 3D fast gradient echo (Efgre3d) sequence (group 2). Pericicatricial residual cancer was confirmed histologically in 29 of the 50 patients. The overall sensitivity, specificity, accuracy, positive predictive value, and negative predictive value of MRI for residual cancer diagnosis was 66, 81, 72, 83 and 63%. A nodular, thick and discontinuous enhanced rim around the scar is indicative of a residual tumor. However, false-positive findings due to granulation or proliferative fibrocystic change remain limitations.

A new method for weakening the combined effect of residual errors on multibeam bathymetric data

Science.gov (United States)

Zhao, Jianhu; Yan, Jun; Zhang, Hongmei; Zhang, Yuqing; Wang, Aixue

2014-12-01

Multibeam bathymetric system (MBS) has been widely applied in the marine surveying for providing high-resolution seabed topography. However, some factors degrade the precision of bathymetry, including the sound velocity, the vessel attitude, the misalignment angle of the transducer and so on. Although these factors have been corrected strictly in bathymetric data processing, the final bathymetric result is still affected by their residual errors. In deep water, the result usually cannot meet the requirements of high-precision seabed topography. The combined effect of these residual errors is systematic, and it's difficult to separate and weaken the effect using traditional single-error correction methods. Therefore, the paper puts forward a new method for weakening the effect of residual errors based on the frequency-spectrum characteristics of seabed topography and multibeam bathymetric data. Four steps, namely the separation of the low-frequency and the high-frequency part of bathymetric data, the reconstruction of the trend of actual seabed topography, the merging of the actual trend and the extracted microtopography, and the accuracy evaluation, are involved in the method. Experiment results prove that the proposed method could weaken the combined effect of residual errors on multibeam bathymetric data and efficiently improve the accuracy of the final post-processing results. We suggest that the method should be widely applied to MBS data processing in deep water.

Residual nilpotence and residual solubility of groups

International Nuclear Information System (INIS)

Mikhailov, R V

2005-01-01

The properties of the residual nilpotence and the residual solubility of groups are studied. The main objects under investigation are the class of residually nilpotent groups such that each central extension of these groups is also residually nilpotent and the class of residually soluble groups such that each Abelian extension of these groups is residually soluble. Various examples of groups not belonging to these classes are constructed by homological methods and methods of the theory of modules over group rings. Several applications of the theory under consideration are presented and problems concerning the residual nilpotence of one-relator groups are considered.

Use of residual wood in the cement manufacturing process

International Nuclear Information System (INIS)

Gue, R.

2005-01-01

This PowerPoint presentation discussed the use of wood residuals in the cement manufacturing process. An outline of the cement manufacturing process was presented. Raw materials are combined in exact proportions to create a chemically correct mix, which is then pulverized in a mill. The mix is then burned in a kiln. The end product is cooled to form the pellet sized material known as clinker, which is then milled to form cement. The combustion and destruction characteristics of a cement kiln were presented. Modern cement kilns require approximately 3.2 Gj of energy to produce one tonne of cement. It was noted that wood residuals do not contain halogens, sulfur or other materials detrimental to the cement manufacturing process. Possible injection points for kilns were presented. Various studies have shown that wood residuals can be safely used as a fuel in the manufacture of cement. Environmental benefits derived from using wood included the complete destruction of organic portions, and the fact that residual ash becomes an indistinguishable part of the final product. It was concluded that wood residual materials are a satisfactory alternative fuel for the cement industry. tabs., figs

Lysine as helix C-capping residue in a synthetic peptide.

Science.gov (United States)

Esposito, G; Dhanapal, B; Dumy, P; Varma, V; Mutter, M; Bodenhausen, G

1997-01-01

The structure of the synthetic peptide CH3CO(Leu-Ser-Leu-Leu-Leu-Ser-Leu)3Lys-NH2 in trifluoroethanol/water 60/40 (volume ratio) was characterized by two-dimensional nmr spectroscopy. The peptide, closely related to the amphiphilic helix models designed by W. F. De-Grado and co-workers to mimic protein ion channels [(1988) Science, Vol. 240, p. 1177-1181], folds into a regular helix spanning residues 1-20. Evidence for a helix C-terminal capping conformation, involving the terminal lysine residue, was observed from Overhauser effects and checked for consistency by restrained molecular dynamics simulations. The side-chain amino group of Lys22 forms a hydrogen bond with the carbonyl of Leu18, and the distorted helical geometry of the terminal dipeptide allows the inclusion of a water bridge between the backbone NH of the Lys22 residue and the carbonyls of Leu19 and Ser20.

Differential Effects of Visual-Acoustic Biofeedback Intervention for Residual Speech Errors

Science.gov (United States)

McAllister Byun, Tara; Campbell, Heather

2016-01-01

Recent evidence suggests that the incorporation of visual biofeedback technologies may enhance response to treatment in individuals with residual speech errors. However, there is a need for controlled research systematically comparing biofeedback versus non-biofeedback intervention approaches. This study implemented a single-subject experimental design with a crossover component to investigate the relative efficacy of visual-acoustic biofeedback and traditional articulatory treatment for residual rhotic errors. Eleven child/adolescent participants received ten sessions of visual-acoustic biofeedback and 10 sessions of traditional treatment, with the order of biofeedback and traditional phases counterbalanced across participants. Probe measures eliciting untreated rhotic words were administered in at least three sessions prior to the start of treatment (baseline), between the two treatment phases (midpoint), and after treatment ended (maintenance), as well as before and after each treatment session. Perceptual accuracy of rhotic production was assessed by outside listeners in a blinded, randomized fashion. Results were analyzed using a combination of visual inspection of treatment trajectories, individual effect sizes, and logistic mixed-effects regression. Effect sizes and visual inspection revealed that participants could be divided into categories of strong responders (n = 4), mixed/moderate responders (n = 3), and non-responders (n = 4). Individual results did not reveal a reliable pattern of stronger performance in biofeedback versus traditional blocks, or vice versa. Moreover, biofeedback versus traditional treatment was not a significant predictor of accuracy in the logistic mixed-effects model examining all within-treatment word probes. However, the interaction between treatment condition and treatment order was significant: biofeedback was more effective than traditional treatment in the first phase of treatment, and traditional treatment was more effective

Effect of Dodonaea viscosa Jacq. residues on growth and yield of ...

African Journals Online (AJOL)

This study was to evaluate the effect of Dodonaea viscosa Jacq. residues on mungbean (Vigna mungo L.Hepper) local cultivar. An experiment [using randomized complete block design (RCBD) design] with three replications was conducted in 2010. The trial comprised of four treatments such as mulching, incorporation into ...

Mechanism of Flavoprotein l-6-Hydroxynicotine Oxidase: pH and Solvent Isotope Effects and Identification of Key Active Site Residues.

Science.gov (United States)

Fitzpatrick, Paul F; Chadegani, Fatemeh; Zhang, Shengnan; Dougherty, Vi

2017-02-14

The flavoenzyme l-6-hydroxynicotine oxidase is a member of the monoamine oxidase family that catalyzes the oxidation of (S)-6-hydroxynicotine to 6-hydroxypseudooxynicotine during microbial catabolism of nicotine. While the enzyme has long been understood to catalyze oxidation of the carbon-carbon bond, it has recently been shown to catalyze oxidation of a carbon-nitrogen bond [Fitzpatrick, P. F., et al. (2016) Biochemistry 55, 697-703]. The effects of pH and mutagenesis of active site residues have now been utilized to study the mechanism and roles of active site residues. Asn166 and Tyr311 bind the substrate, while Lys287 forms a water-mediated hydrogen bond with flavin N5. The N166A and Y311F mutations result in ∼30- and ∼4-fold decreases in k cat /K m and k red for (S)-6-hydroxynicotine, respectively, with larger effects on the k cat /K m value for (S)-6-hydroxynornicotine. The K287M mutation results in ∼10-fold decreases in these parameters and a 6000-fold decrease in the k cat /K m value for oxygen. The shapes of the pH profiles are not altered by the N166A and Y311F mutations. There is no solvent isotope effect on the k cat /K m value for amines. The results are consistent with a model in which both the charged and neutral forms of the amine can bind, with the former rapidly losing a proton to a hydrogen bond network of water and amino acids in the active site prior to the transfer of hydride to the flavin.

Harvesting and handling agricultural residues for energy

Energy Technology Data Exchange (ETDEWEB)

Jenkins, B.M.; Summer, H.R.

1986-05-01

Significant progress in understanding the needs for design of agricultural residue collection and handling systems has been made but additional research is required. Recommendations are made for research to (a) integrate residue collection and handling systems into general agricultural practices through the development of multi-use equipment and total harvest systems; (b) improve methods for routine evaluation of agricultural residue resources, possibly through remote sensing and image processing; (c) analyze biomass properties to obtain detailed data relevant to engineering design and analysis; (d) evaluate long-term environmental, social, and agronomic impacts of residue collection; (e) develop improved equipment with higher capacities to reduce residue collection and handling costs, with emphasis on optimal design of complete systems including collection, transportation, processing, storage, and utilization; and (f) produce standard forms of biomass fuels or products to enhance material handling and expand biomass markets through improved reliability and automatic control of biomass conversion and other utilization systems. 118 references.

Effect of process parameters on the residual stresses in AA5083-H321 friction stir welds

Energy Technology Data Exchange (ETDEWEB)

Lombard, H. [NMMU, Gardham Avenue, PO Box 77000, 6031 Port Elizabeth (South Africa); University of Plymouth, Drake Circus, Plymouth PL4 8AA (United Kingdom); Hattingh, D.G. [NMMU, Gardham Avenue, PO Box 77000, 6031 Port Elizabeth (South Africa); Steuwer, A. [NMMU, Gardham Avenue, PO Box 77000, 6031 Port Elizabeth (South Africa); FaME38 at the ILL-ESRF, 6 rue J Horowitz, 38042 Grenoble (France); University of Plymouth, Drake Circus, Plymouth PL4 8AA (United Kingdom)], E-mail: steuwer@ill.fr; James, M.N. [NMMU, Gardham Avenue, PO Box 77000, 6031 Port Elizabeth (South Africa); University of Plymouth, Drake Circus, Plymouth PL4 8AA (United Kingdom)

2009-02-15

This paper investigates the effect of varying welding parameters on the residual stress profiles in friction stir welds of aluminium alloy AA5083-H321, which were created on a fully instrumented friction welding machine. The residual stresses were determined non-destructively using synchrotron X-ray diffraction. The width and maximum of the residual stress profile show clear correlation with the heat input, and in particular feed rate, which was found to be the dominant parameter.

Effect of texture and grain size on the residual stress of nanocrystalline thin films

Science.gov (United States)

Cao, Lei; Sengupta, Arkaprabha; Pantuso, Daniel; Koslowski, Marisol

2017-10-01

Residual stresses develop in thin film interconnects mainly as a result of deposition conditions and multiple thermal loading cycles during the manufacturing flow. Understanding the relation between the distribution of residual stress and the interconnect microstructure is of key importance to manage the nucleation and growth of defects that can lead to failure under reliability testing and use conditions. Dislocation dynamics simulations are performed in nanocrystalline copper subjected to cyclic loading to quantify the distribution of residual stresses as a function of grain misorientation and grain size distribution. The outcomes of this work help to evaluate the effect of microstructure in thin films failure by identifying potential voiding sites. Furthermore, the simulations show how dislocation structures are influenced by texture and grain size distribution that affect the residual stress. For example, when dislocation loops reach the opposite grain boundary during loading, these dislocations remain locked during unloading.

Accumulative effect of food residues on intestinal gas production.

Science.gov (United States)

Mego, M; Accarino, A; Malagelada, J-R; Guarner, F; Azpiroz, F

2015-11-01

As mean transit time in the colon is longer than the interval between meals, several consecutive meal loads accumulate, and contribute to colonic biomass. Our aim was to determine the summation effect of fermentable food residues on intestinal gas production. In eight healthy subjects, the volume of endogenous intestinal gas produced in the intestine over a 4-h period was measured by means of a wash-out technique, using an exogenous gas infusion into the jejunum (24 mL/min) and collection of the effluent via a rectal Foley catheter. The exogenous gas infused was labeled (5% SF6 ) to calculate the proportion of endogenous intestinal gas evacuated. In each subject, four experiments were performed ≥1 week apart combining a 1-day high- or low-flatulogenic diet with a test meal or fast. Basal conditions: on the low-flatulogenic diet, intestinal gas production during fasting over the 4-h study period was 609 ± 63 mL. Effect of diet: during fasting, intestinal gas production on the high-flatulogenic diet was 370 ± 146 mL greater than on the low-flatulogenic diet (p = 0.040). Effect of test meal: on the low-flatulogenic diet, intestinal gas production after the test meal was 681 ± 114 mL greater than during fasting (p = 0.001); a similar effect was observed on the high-flatulogenic diet (599 ± 174 mL more intestinal gas production after the test meal than during fasting; p = 0.021). Our data demonstrate temporal summation effects of food residues on intestinal gas production. Hence, intestinal gas production depends on pre-existing and on recent colonic loads of fermentable foodstuffs. © 2015 John Wiley & Sons Ltd.

[Development of residual voltage testing equipment].

Science.gov (United States)

Zeng, Xiaohui; Wu, Mingjun; Cao, Li; He, Jinyi; Deng, Zhensheng

2014-07-01

For the existing measurement methods of residual voltage which can't turn the power off at peak voltage exactly and simultaneously display waveforms, a new residual voltage detection method is put forward in this paper. First, the zero point of the power supply is detected with zero cross detection circuit and is inputted to a single-chip microcomputer in the form of pulse signal. Secend, when the zero point delays to the peak voltage, the single-chip microcomputer sends control signal to power off the relay. At last, the waveform of the residual voltage is displayed on a principal computer or oscilloscope. The experimental results show that the device designed in this paper can turn the power off at peak voltage and is able to accurately display the voltage waveform immediately after power off and the standard deviation of the residual voltage is less than 0.2 V at exactly one second and later.

Utilization of organic residues using heterotrophic microalgae and insects.

Science.gov (United States)

Pleissner, Daniel; Rumpold, Birgit A

2018-02-01

Various organic residues occur globally in the form of straw, wood, green biomass, food waste, feces, manure etc. Other utilization strategies apart from anaerobic digestion, composting and incineration are needed to make use of the whole potential of organic residues as sources of various value added compounds. This review compares the cultivation of heterotrophic microalgae and insects using organic residues as nutrient sources and illuminates their potential with regard to biomass production, productivity and yield, and utilization strategies of produced biomasses. Furthermore, cultivation processes as well as advantages and disadvantages of utilization processes are identified and discussed. It was shown that both heterotrophic algae and insects are able to reduce a sufficient amount of organic residues by converting it into biomass. The biomass composition of both organisms is similar which allows similar utilization strategies in food and feed, chemicals and materials productions. Even though insect is the more complex organism, biomass production can be carried out using simple equipment without sterilization and hydrolysis of organic residues. Contrarily, heterotrophic microalgae require a pretreatment of organic residues in form of sterilization and in most cases hydrolysis. Interestingly, the volumetric productivity of insect biomass exceeds the productivity of algal biomass. Despite legal restrictions, it is expected that microalgae and insects will find application as alternative food and feed sources in the future. Copyright © 2017 Elsevier Ltd. All rights reserved.

Characteristics of lactic acid bacteria isolates and their effect on silage fermentation of fruit residues.

Science.gov (United States)

Yang, Jinsong; Tan, Haisheng; Cai, Yimin

2016-07-01

The natural lactic acid bacteria (LAB) population, chemical composition, and silage fermentation of fruit residues were studied. Eighty-two strains of LAB were isolated from fruit residues such as banana leaf and stem, pineapple peel, and papaya peel. All strains were gram-positive and catalase-negative bacteria, and they were divided into 7 groups (A-G) according to morphological and biochemical characters. Strains in groups A to F were rods, and group G was cocci. Group F produced gas from glucose; other groups did not. Groups A to C and F formed dl-lactic acid, whereas groups D, E, and G formed l-lactic acid. Based on the 16S rRNA gene sequence and DNA-DNA hybridization analysis, groups A to G strains were identified as Lactobacillus plantarum (54.9% of the total isolates), Lactobacillus paraplantarum (3.6%), Lactobacillus nagelii (8.5%), Lactobacillus perolens (4.9%), Lactobacillus casei (11.0%), Lactobacillus fermentum (9.8%), and Enterococcus gallinarum (7.3%), respectively. Lactobacillus plantarum and Lactobacillus casei are the most frequently isolated from fruit residues as a dominant species, and they could grow at a lower pH conditions and produce more lactic acid than other isolates. Pineapple and papaya peels contained higher crude protein (11.5-13.8%) and water-soluble carbohydrate (16.8-22.4%), but lower acid detergent fiber contents (21.2 to 26.4%) than banana stems and leaves (8.2% crude protein, 42.8% acid detergent fiber, and 5.1% water-soluble carbohydrate). Compared with banana stem and leaf silages, the pineapple and papaya peel silages were well preserved with a lower pH and higher lactate content. The study suggests that the fruit residues contain excellent LAB species and abundant feed nutrients, and that they can be preserved as silage to be potential food resources for livestock. Copyright © 2016 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Cumulative effects of white clover residues on the changes in soil ...

African Journals Online (AJOL)

STORAGESEVER

2009-05-18

May 18, 2009 ... The residual effects of white clover on soil properties indicated a significant increase in saturation percentage (17–23%) and .... determined by leaching the soil with KCl followed by extraction of ...... accumulation, and oil quality of French basil. ... of the Final Workshop of the Farming System Integrated Pest.

Residual generator for cardiovascular anomalies detection

KAUST Repository

Belkhatir, Zehor

2014-06-01

This paper discusses the possibility of using observer-based approaches for cardiovascular anomalies detection and isolation. We consider a lumped parameter model of the cardiovascular system that can be written in a form of nonlinear state-space representation. We show that residuals that are sensitive to variations in some cardiovascular parameters and to abnormal opening and closure of the valves, can be generated. Since the whole state is not easily available for measurement, we propose to associate the residual generator to a robust extended kalman filter. Numerical results performed on synthetic data are provided.

Effects of coffee processing residues on anaerobic microorganisms and corresponding digestion performance.

Science.gov (United States)

Rojas-Sossa, Juan Pablo; Murillo-Roos, Mariana; Uribe, Lidieth; Uribe-Lorio, Lorena; Marsh, Terence; Larsen, Niels; Chen, Rui; Miranda, Alberto; Solís, Kattia; Rodriguez, Werner; Kirk, Dana; Liao, Wei

2017-12-01

The objective of this study was to delineate the effects of different coffee processing residues on the anaerobic microbes and corresponding digestion performance. The results elucidated that mucilage-rich feed enhanced the accumulation of methanogens, which consequently led to better digestion performance of biogas production. Fifty percent more methane and up to 3 times more net energy (heat and electricity) output were achieved by the digestion of the mucilage-rich feed (M3). The microbial community and statistical analyses further elucidated that different residues in the feed had significant impact on microbial distribution and correspondingly influenced the digestion performance. Copyright © 2017 Elsevier Ltd. All rights reserved.

Analyses of edge effects on residual stresses in film strip/substrate systems

International Nuclear Information System (INIS)

Hsueh, Chun-Hway

2000-01-01

The residual stress distribution in a thin-film strip overlaid on a substrate is influenced by the edges of the strip. An analytical model is developed to derive a closed-form solution for the stress distribution along the film width. Because the film is much thinner than the substrate, the stress variation through the film thickness is ignored; however, the stress variation through the substrate thickness is considered in the analysis. Compared to the existing analytical models, the present model is more rigorous and the analytical results agree better with both finite element results and experimental measurements. (c) 2000 American Institute of Physics

Pyrolysis and reutilization of plant residues after phytoremediation of heavy metals contaminated sediments: For heavy metals stabilization and dye adsorption.

Science.gov (United States)

Gong, Xiaomin; Huang, Danlian; Liu, Yunguo; Zeng, Guangming; Wang, Rongzhong; Wei, Jingjing; Huang, Chao; Xu, Piao; Wan, Jia; Zhang, Chen

2018-04-01

This study aimed to investigate the effect of pyrolysis on the stabilization of heavy metals in plant residues obtained after phytoremediation. Ramie residues, being collected after phytoremediation of metal contaminated sediments, were pyrolyzed at different temperatures (300-700 °C). Results indicated that pyrolysis was effective in the stabilization of Cd, Cr, Zn, Cu, and Pb in ramie residues by converting the acid-soluble fraction of metals into residual form and decreasing the TCLP-leachable metal contents. Meanwhile, the reutilization potential of using the pyrolysis products generated from ramie residues obtained after phytoremediation as sorbents was investigated. Adsorption experiments results revealed that the pyrolysis products presented excellent ability to adsorb methylene blue (MB) with a maximum adsorption capacity of 259.27 mg/g. This study demonstrated that pyrolysis could be used as an efficient alternative method for stabilizing heavy metals in plant residues obtained after phytoremediation, and their pyrolysis products could be reutilized for dye adsorption. Copyright © 2018 Elsevier Ltd. All rights reserved.

Cumulative effects of white clover residues on the changes in soil ...

African Journals Online (AJOL)

White clover grows naturally all over the Himalayan regions including the hilly areas of the state of Azad Jammu and Kashmir (AJK), Pakistan. This study was conducted to investigate the effects of white clover residues alone or in combination with phosphorus (P) fertilizer on maize (Zea mays L.) yield, nutrient uptake and ...

Effect of increased exposure times on amount of residual monomer released from single-step self-etch adhesives.

Science.gov (United States)

Altunsoy, Mustafa; Botsali, Murat Selim; Tosun, Gonca; Yasar, Ahmet

2015-10-16

The aim of this study was to evaluate the effect of increased exposure times on the amount of residual Bis-GMA, TEGDMA, HEMA and UDMA released from single-step self-etch adhesive systems. Two adhesive systems were used. The adhesives were applied to bovine dentin surface according to the manufacturer's instructions and were polymerized using an LED curing unit for 10, 20 and 40 seconds (n = 5). After polymerization, the specimens were stored in 75% ethanol-water solution (6 mL). Residual monomers (Bis-GMA, TEGDMA, UDMA and HEMA) that were eluted from the adhesives (after 10 minutes, 1 hour, 1 day, 7 days and 30 days) were analyzed by high-performance liquid chromatography (HPLC). The data were analyzed using 1-way analysis of variance and Tukey HSD tests. Among the time periods, the highest amount of released residual monomers from adhesives was observed in the 10th minute. There were statistically significant differences regarding released Bis-GMA, UDMA, HEMA and TEGDMA between the adhesive systems (p<0.05). There were no significant differences among the 10, 20 and 40 second polymerization times according to their effect on residual monomer release from adhesives (p>0.05). Increasing the polymerization time did not have an effect on residual monomer release from single-step self-etch adhesives.

Effectiveness of the compound chlorpyrifos+ cypermethrin+citronellal against Alphitobius diaperinus: laboratory analysis and residue determination in carcasses

Directory of Open Access Journals (Sweden)

GS Silva

2007-09-01

Full Text Available Effectiveness, biological security and the absence of residues in meat and/or eggs must be considered when recommending options for the control Alphitobius diaperinus in poultry production environments. This research study evaluated the effectiveness of cypermethrin+ chlorpyrifos+citronellal in the control of A. diaperinus, including analysis for the presence of residues of this compound in poultry carcasses (experimental farm. Two studies were carried out under laboratory conditions. One used paper filters a four dilutions of the compound, and the other used a container including with pulverized broiler litter and the compound. The analysis of carcasses for residues was conducted in broilers that raised in a broiler house treated (floor and/or litter with the compound at a dilution of 1:800. Birds were regularly sacrificed, submitted to necropsy, and liver, muscle and fat fragments were collected. Gas chromatography was used to identify the possible presence of any chemical residue in these samples. High effectiveness rates against A.diaperinus were observed in the two laboratory studies, as well as the absence of residues in the carcasses. This compound, used in the studied concentrations, can be recommended as a valuable alternative for the control and treatment of A. diaperinus.

The effect of gamma irradiation on in vitro digestible energy of some agricultural residues

International Nuclear Information System (INIS)

Al-Masri, M.R.

1993-03-01

Experiments have been carried out on the effect of gamma irradiation on total energy, dry organic matter digestibility and on digestible energy of organic matter for some agricultural residues (maize straw, lentils straw, cottonwood, residues of apple-tree pruning, olive-cake first and second treatment). Sample were irradiated at 0, 50 and 100 KGy. Total energy was estimated by calorimeter. Digestibility was estimated in vitro by the method of Tilly and Terry (1963). Two sheep with rumen fistula were used as rumen liquor donating animals. Irradiation resulted in increasing the digestion of organic and dry matter and also the digestible energy of organic matter in all residues used except lentils straw and olive-cake first treatment. The increase in digestible energy values of organic matter (kJ) at dose of 100 KGy were: 155, 105, 71 and 25 for residue of apple-tree pruning, maize straw, cottonwood and olive-cake second treatment, respectively. (author).28 refs., 10 figs., 5 tabs

Hemodynamic effects of closure of residual arteriovenous fistulae during in situ graft procedures

DEFF Research Database (Denmark)

Laustsen, Jesper; Nielsen, Henriette Svarre; Pedersen, Erik Morre

2011-01-01

lower limb ischemia were obtained. Direct measurements of proximal and distal blood pressures in the graft were taken and simultaneous determinations of volume blood flow proximally and distally in the graft with ultrasound transit time technique before and after closure of residual fistulae were made......The objective was to study the intraoperative hemodynamic effects of closure of residual arteriovenous fistulae during in situ saphenous vein graft procedures. Data on 60 residual arteriovenous fistulae in nine patients (five men) with a median age of 74 years (range 64-83 years) with critical....... Closure of a fistula with blood flow around or below 100 mL/min did not increase distal outflow, whereas closure of fistulae with higher blood flow resulted in unpredictable changes in distal outflow. Only fistulae with a blood flow above approximately 100 mL/min may be of hemodynamic significance....

Effects of fatigue and environment on residual strengths of center-cracked graphite/epoxy buffer strip panels

Science.gov (United States)

Bigelow, Catherine A.

1989-01-01

The effects of fatigue, moisture conditioning, and heating on the residual tension strengths of center-cracked graphite/epoxy buffer strip panels were evaluated using specimens made with T300/5208 graphite epoxy in a 16-ply quasi-isotropic layup, with two different buffer strip materials, Kevlar-49 or S-glass. It was found that, for panels subjected to fatigue loading, the residual strengths were not significantly affected by the fatigue loading, the number of repetitions of the loading spectrum, or the maximum strain level. The moisture conditioning reduced the residual strengths of the S-glass buffer strip panels by 10 to 15 percent below the ambient results, but increased the residual strengths of the Kevlar-49 buffer strip panels slightly. For both buffer strip materials, the heat increased the residual strengths of the buffer strip panels slightly over the ambient results.

Evaluation of the effectiveness of olive cake residue as an expansive soil stabilizer

Science.gov (United States)

Nalbantoglu, Zalihe; Tawfiq, Salma

2006-08-01

The quantity of the by-product olive cake residue generated in most parts of the Mediterranean countries continues to increase and expected to double in amount within 10 15 years. This increase intensifies the problems associated with the disposal of this by-product. Olive cake residue has a potential for use as a soil stabilizer and large volumes can be beneficially used. This study is directed toward determining if olive cake residue can be utilized to increase the strength and stability of expansive soils which constitute a costly natural hazard to lightweight structures on shallow foundations. A series of laboratory tests using engineering properties, such as Atterberg limits, moisture-density relationship (compaction), swell, unconfined compressive strength were undertaken to evaluate the effectiveness and performance of the olive cake residue as a soil stabilizer. Test results indicate that an addition of only 3% burned olive waste into the soil causes a reduction in plasticity, volume change and an increase in the unconfined compressive strength. However, it was observed that the presence of burned olive waste in the soil greater than 3% caused an increase in the compressibility and a decrease in the unconfined compressive strength. Test results indicate that the use of olive waste in soil stabilization gives greater benefits to the environment than simply disposing of the by-product, olive cake residue.

Residual analysis for spatial point processes

DEFF Research Database (Denmark)

Baddeley, A.; Turner, R.; Møller, Jesper

We define residuals for point process models fitted to spatial point pattern data, and propose diagnostic plots based on these residuals. The techniques apply to any Gibbs point process model, which may exhibit spatial heterogeneity, interpoint interaction and dependence on spatial covariates. Ou...... or covariate effects. Q-Q plots of the residuals are effective in diagnosing interpoint interaction. Some existing ad hoc statistics of point patterns (quadrat counts, scan statistic, kernel smoothed intensity, Berman's diagnostic) are recovered as special cases....

Investigation on reusing water treatment residuals to remedy soil contaminated with multiple metals in Baiyin, China

International Nuclear Information System (INIS)

Wang, Changhui; Zhao, Yuanyuan; Pei, Yuansheng

2012-01-01

Highlights: ► Fe/Al water treatment residuals (FARs) can stabilize As, Pb, Ni, Zn, Cr and Cu. ► FARs cannot stabilize Ba and Cd. ► The properties of FARs and soil affect the FARs’ ability of stabilizing metals. - Abstract: In this work, the remediation of soils contaminated with multiple metals using ferric and alum water treatment residuals (FARs) in Baiyin, China, was investigated. The results of metals fractionation indicated that after the soil was treated with FARs, arsenic (As), lead (Pb), nickel (Ni), zinc (Zn) and copper (Cu) could be transformed into more stable forms, i.e., As bound in crystalline Fe/Al oxides and other metals in the oxidable and residual forms. However, the forms of chromium (Cr) and cadmium (Cd) were unaffected. Interestingly, due to the effect of FARs, barium (Ba) was predominantly transformed into more mobile forms. The bioaccessibility extraction test demonstrated that the FARs reduced the bioaccessibility of As by 25%, followed by Cu, Cr, Zn, Ni and Pb. The bioaccessibility of Cd and Ba were increased; in particular, there was an increase of 41% for Ba at the end of the test. In conclusion, the FARs can be used to remedy soil contaminated with multiple metals, but comprehensive studies are needed before practical applications of this work.

Effect of Household Coffee Processing on Pesticide Residues as a Means of Ensuring Consumers' Safety.

Science.gov (United States)

Mekonen, Seblework; Ambelu, Argaw; Spanoghe, Pieter

2015-09-30

Coffee is a highly consumed and popular beverage all over the world; however, coffee beans used for daily consumption may contain pesticide residues that may cause adverse health effects to consumers. In this monitoring study, the effect of household coffee processing on pesticide residues in coffee beans was investigated. Twelve pesticides, including metabolites and isomers (endosulfan α, endosulfan β, cypermethrin, permethrin, deltamethrin, chlorpyrifos ethyl, heptachlor epoxide, hexachlorobenzene, p'p-DDE, p'p-DDD, o'p-DDT, and p'p-DDT) were spiked in coffee beans collected from a local market in southwestern Ethiopia. The subsequent household coffee processing conditions (washing, roasting, and brewing) were established as closely as possible to the traditional household coffee processing in Ethiopia. Washing of coffee beans showed 14.63-57.69 percent reduction, while the roasting process reduced up to 99.8 percent. Chlorpyrifos ethyl, permethrin, cypermethrin, endosulfan α and β in roasting and all of the 12 pesticides in the coffee brewing processes were not detected. Kruskal-Wallis analysis indicated that the reduction of pesticide residues by washing is significantly different from roasting and brewing (P coffee roasting and brewing (P > 0.05). The processing factor (PF) was less than one (PF coffee beans. The cumulative effect of the three processing methods has a paramount importance in evaluating the risks associated with ingestion of pesticide residues, particularly in coffee beans.

Preliminary evaluation of alternative forms for immobilization of Hanford high-level defense wastes

International Nuclear Information System (INIS)

Schulz, W.W.; Beary, M.M.; Gallagher, S.A.; Higley, B.A.; Johnston, R.G.; Jungfleisch, F.M.; Kupfer, M.J.; Palmer, R.A.; Watrous, R.A.; Wolf, G.A.

1980-09-01

A preliminary evaluation of solid waste forms for immobilization of Hanford high-level radioactive defense wastes is presented. Nineteen different waste forms were evaluated and compared to determine their applicability and suitability for immobilization of Hanford salt cake, sludge, and residual liquid. This assessment was structured to address waste forms/processes for several different leave-retrieve long-term Hanford waste management alternatives which give rise to four different generic fractions: (1) sludge plus long-lived radionuclide concentrate from salt cake and residual liquid; (2) blended wastes (salt cake plus sludge plus residual liquid); (3) residual liquid; and (4) radionuclide concentrate from residual liquid. Waste forms were evaluated and ranked on the basis of weighted ratings of seven waste form and seven process characteristics. Borosilicate Glass waste forms, as marbles or monoliths, rank among the first three choices for fixation of all Hanford high-level wastes (HLW). Supergrout Concrete (akin to Oak Ridge National Laboratory Hydrofracture Process concrete) and Bitumen, low-temperature waste forms, rate high for bulk disposal immobilization of high-sodium blended wastes and residual liquid. Certain multi-barrier (e.g., Coated Ceramic) and ceramic (SYNROC Ceramic, Tailored Ceramics, and Supercalcine Ceramic) waste forms, along with Borosilicate Glass, are rated as the most satisfactory forms in which to incorporate sludges and associated radionuclide concentrates. The Sol-Gel process appears superior to other processes for manufacture of a generic ceramic waste form for fixation of Hanford sludge. Appropriate recommendations for further research and development work on top ranking waste forms are made

Effects of advanced laser processing on the microstructure and residual stresses of H13 tool steel

OpenAIRE

Trojan, Karel; Ocelík, Václav; Ganev, Nikolaj; Němeček, Stanislav; Čapek, Jiří

2017-01-01

The aim of this paper is to describe the effects of laser processing on the microstructure and residual stresses of laser cladded H13 tool steel on the classical construct steel S355 substrate. This research paper concludes that in this case of laser cladding, phase transformation and not shrinkage is likely to be a dominant effect on the formation of compressive residual stresses along the clad. Furthermore, martensitic structure and unequal concentration of alloying elements was observed on...

Effect of residual stresses on the reliability of components under fatigue

International Nuclear Information System (INIS)

Ruestenberg, I.

1995-01-01

The assurance of the reliability of mechanical components relative to a variety of failure mechanisms is of decisive technical, industrial, and economic importance. In this dissertation, the reliability, i.e. the probability that the lifetime does not fall below a given value, is examined with respect to the particularly important failure mechanisms of fracture and fatigue. The general problem of uniaxial fatigue is studied on the basis of both continuum damage mechanics and crack mechanics. In particular, the mechanisms of crack initiation, as characterized by the Coffin-Manson-Neuber local strain-life equations for notched components as well as the mechanism of crack growth, as governed by the Paris-Erdogang relation, are taken into account. The nonlinear fatigue damage accumulation process for components subjected to general, cyclic loading histories is modeled by a multilinear damage law which allows, in principle, to characterize the subsequent activation of different fatigue mechanisms. Explicit equations are developed for quintuple-, quadruple-, and triple-linear damage accumulation. Particularly promising appears the triple-linear damage approach which allows, in principle, the identification of a nucleation, an initiation, and a final growth stage up to rupture of fatigue cracks. The beneficial effect of intentionally induced compressive residual stresses on the lifetime of the component is investigated. To this end, an elasto-plastic contact problem, based on Prandtl-Reuss' constitutive equations, is numerically solved, and the residual stress field, as it is typically produced by the mechanical process of cold rolling, is established. Assessments of the effect of adaptation, i.e. the subsequent reduction of the residual stresses due to cyclic in-service loading as well as of the effect of unavoidable surface roughness, introduced by manufacturing processes like forging, are carried out. (author) figs., tabs., refs

Improved performance and stability of field-effect transistors with polymeric residue-free graphene channel transferred by gold layer.

Science.gov (United States)

Jang, Mi; Trung, Tran Quang; Jung, Jin-Heak; Kim, Bo-Yeong; Lee, Nae-Eung

2014-03-07

One of the most significant issues that occurs when applying chemical-vapor deposited (CVD) graphene (Gr) to various high-performance device applications is the result of polymeric residues. Polymeric residues remain on the Gr surface during Gr polymer support transfer to an arbitrary substrate, and these residues degrade CVD Gr electrical properties. In this paper, we propose that a thin layer of gold be used as a CVD Gr transfer layer, instead of a polymer support layer, to enable a polymer residue-free transfer. Comparative investigation of the surface morphological and qualitative analysis of residues on Gr surfaces and Gr field-effect transistors (GFETs) using two transfer methods demonstrates that gold-transferred Gr, with uniform, smooth, and clean surfaces, enable GFETs to perform better than Gr transferred by the polymer, polymethylmethacrylate (PMMA). In GFETs fabricated by the gold transfer method, field-effect carrier mobility was greatly enhanced and the position of the Dirac point was significantly reduced compared to GFETs fabricated by the PMMA transfer method. In addition, compared to the PMMA-transferred GFETs, the gold-transferred GFETs showed greatly increased stability with smaller hysteresis and higher resistance to gate bias stress effects. These results suggest that the gold transfer method for Gr provides significant improvements in GFET performance and reliability by minimizing the polymeric residues and defects on Gr.

The effect of pesticide residue on caged mosquito bioassays.

Science.gov (United States)

Barber, J A S; Greer, Mike; Coughlin, Jamie

2006-09-01

Wind tunnel experiments showed that secondary pickup of insecticide residue by mosquitoes in cage bioassays had a significant effect on mortality. Cage bioassays using adult Ochlerotatus taeniorhynchus (Wiedemann) investigated the effect of exposure time to a contaminated surface. Cages were dosed in a wind tunnel using the LC50 for naled (0.124 mg a.i./ml) and an LC25 (0.0772 mg a.i./ml) for naled. Half of the bioassay mosquitoes were moved directly into clean cages with the other half remaining in the sprayed, hence contaminated, cage. Treatment mortality was assessed at 8, 15, 30, 60, 120, 240, and 1,440 min postapplication. Cage contamination had a significant effect on mosquito mortality for both the LC25 and LC50 between 15 and 30 min postapplication.

Effects of hydrated lime on radionuclides stabilization of Hanford tank residual waste.

Science.gov (United States)

Wang, Guohui; Um, Wooyong; Cantrell, Kirk J; Snyder, Michelle M V; Bowden, Mark E; Triplett, Mark B; Buck, Edgar C

2017-10-01

Chemical stabilization of tank residual waste is part of a Hanford Site tank closure strategy to reduce overall risk levels to human health and the environment. In this study, a set of column leaching experiments using tank C-104 residual waste were conducted to evaluate the leachability of uranium (U) and technetium (Tc) where grout and hydrated lime were applied as chemical stabilizing agents. The experiments were designed to simulate future scenarios where meteoric water infiltrates through the vadose zones into the interior of the tank filled with layers of grout or hydrated lime, and then contacts the residual waste. Effluent concentrations of U and Tc were monitored and compared among three different packing columns (waste only, waste + grout, and waste + grout + hydrated lime). Geochemical modeling of the effluent compositions was conducted to determine saturation indices of uranium solid phases that could control the solubility of uranium. The results indicate that addition of hydrated lime strongly stabilized the uranium through transforming uranium to a highly insoluble calcium uranate (CaUO 4 ) or similar phase, whereas no significant stabilization effect of grout or hydrated lime was observed on Tc leachability. The result implies that hydrated lime could be a great candidate for stabilizing Hanford tank residual wastes where uranium is one of the main concerns. Published by Elsevier Ltd.

The Effect of Kaffir Lime Leaves Distillation Residue Oleoresin Concentration on Active Paper Packaging Characteristics

Science.gov (United States)

Kawiji; Utami, R.; Ulum, S.; Khasanah, L. U.; Manuhara, G. J.; Atmaka, W.

2018-03-01

Oleoresin of kaffir lime leaves distillation residue still contains some active compounds such as Citronellal, β-Citronellol, and Linalool which potential to incorporated on the active paper packaging. The purposes of this study were to determine the effect of kaffir lime leaves distillation residue oleoresin concentration on the physical characteristics, sensory characteristics, and antimicrobial activity of the active paper packaging incorporated with kaffir lime leaves distillation residue oleoresin and to determine the functional groups of active paper packaging. The concentration of kaffir lime leaves distillation residue oleoresin were varied at 0%, 2%, 4% and 6%. The result showed that the addition of kaffir lime leaves distillation residue oleoresin increased the thickness and moisture content of the paper and decreased the tensile strengths and folding endurances of active paper packaging. The microbial inhibition tends to increase along with the higher oleoresin concentration addition. Aromatic CH group were found at a wavelength of 897.90 cm-1 of on paper packaging with 2% oleoresin indicated as functional aromatic functional group allegedly obtained from the kaffir lime leaves oleoresin.

Effect of sodium hypochlorite on typical biofilms formed in drinking water distribution systems.

Science.gov (United States)

Lin, Huirong; Zhu, Xuan; Wang, Yuxin; Yu, Xin

2017-04-01

Human health and biological safety problems resulting from urban drinking water pipe network biofilms pollution have attracted wide concern. Despite the inclusion of residual chlorine in drinking water distribution systems supplies, the bacterium is a recalcitrant human pathogen capable of forming biofilms on pipe walls and causing health risks. Typical drinking water bacterial biofilms and their response to different concentrations of chlorination was monitored. The results showed that the four bacteria all formed single biofilms susceptible to sodium hypochlorite. After 30 min disinfection, biomass and cultivability decreased with increasing concentration of disinfectant but then increased in high disinfectant doses. PMA-qPCR results indicated that it resulted in little cellular damage. Flow cytometry analysis showed that with increasing doses of disinfectant, the numbers of clusters increased and the sizes of clusters decreased. Under high disinfectant treatment, EPS was depleted by disinfectant and about 0.5-1 mg/L of residual chlorine seemed to be appropriate for drinking water treatment. This research provides an insight into the EPS protection to biofilms. Resistance of biofilms against high levels of chlorine has implications for the delivery of drinking water.

Characterization of biomass residues and their amendment effects on water sorption and nutrient leaching in sandy soil.

Science.gov (United States)

Wang, Letian; Tong, Zhaohui; Liu, Guodong; Li, Yuncong

2014-07-01

In this study, we evaluated the efficiency of two types of biomass residues (fermentation residues from a bioethanol process, FB; brown mill residues from a papermaking process, BM) as amendments for a sandy soil. The characteristics of these residues including specific surface areas, morphologies and nutrient sorption capacity were measured. The effects of biorefinery residues on water and nutrient retention were investigated in terms of different particle sizes and loadings. The results indicated that bio-based wastes FB and BM were able to significantly improve water and nutrient retention of sandy soil. The residues with larger surface areas had better water and nutrient retention capability. Specifically, in the addition of 10% loading, FB and BM was able to improve water retention by approximately 150% and 300%, while reduce 99% of ammonium and phosphate concentration in the leachate compare to the soil control, respectively. Copyright © 2014 Elsevier Ltd. All rights reserved.

Effect of irradiation on the evolution of alteration layer formed during nuclear glass leaching

International Nuclear Information System (INIS)

Mougnaud, Sarah

2016-01-01

High-level radioactive waste (HLW) remaining after spent nuclear fuel reprocessing is immobilized within a glass matrix, eventually destined for geological disposal. Water intrusion into the repository is expected after several thousand years. The alteration of a non-radioactive surrogate for nuclear glass has been extensively studied and it has been determined that successive leaching mechanisms lead to the formation of a 'passivating' alteration layer and to the establishment of a residual rate regime in the long term. However, glass packages are submitted to the radioactivity of confined radioelements. This work focuses on the influence of irradiation on the alteration layer formed during the residual rate regime, in a structural and mechanistic point of view. Three focal areas have been selected. Non-radioactive simple glasses have been leached and externally irradiated in order to determine modifications induced by electronic effects (irradiations with electrons and alpha particles). The same type of glass samples have been previously irradiated with heavy ions and their leaching behavior have been studied in order to assess the impact of ballistic dose cumulated by the glass before water intrusion. Leaching behavior of a complex radioactive glass, doped with an alpha-emitter, has been studied to consider a more realistic situation. (author) [fr

The effect of tensioning and sectioning on residual stresses in aluminium AA7749 friction stir welds

International Nuclear Information System (INIS)

Altenkirch, J.; Steuwer, A.; Peel, M.; Richards, D.G.; Withers, P.J.

2008-01-01

Using synchrotron X-ray diffraction the residual stress distribution has been measured in a series of AA7449-W51 aluminium friction stir welds that had been tensioned to different loads during welding. By modifying the stress accumulation path, the application of a tensioning stress has reduced the tensile magnitude of the final residual weld stresses. In the present case the residual stresses were minimised when the applied load is ∼35% of the room temperature yield stress of the parent material. Subsequent sectioning of the weld into shorter test lengths, as might be necessary for weld testing, resulted in a progressive and significant relaxation of the residual stress field. The effect of tensioning on the weld component distortion also has been investigated

Efficiency of the refining processes in removing 14C-dichlorvos residues in soybean oil

International Nuclear Information System (INIS)

Soliman, S.M.

2006-01-01

Crude soybean oil extracted from grains treated with 14 C-dichlorvos at a dose 24 mg insecticide / kg seeds and stored for 30 weeks was subjected to different refining processes such as alkali treatment, bleaching, winterization and deodorization. The effect of the refining processes on the nature and magnitude of the originally present residues was investigated. The insecticide residues in crude oil and cake amounted to 9.5% and 55% , respectively, of original residues inside the seeds. Extraction of the seeds with hexane gave crude oil with 9.5 % of original residues in seeds. The l4 C-activity in the crude stored Soya beans oil could be reduced by about 82% of radioactivity originally present in crude oil eliminated by simulated commercial processes locally used for oil refining. A high percentage of the residues (50-55%) were eliminated during alkali treatment and bleaching. Refining of soybeans oil fortified with '1 4 C-dichlorovos. The final refined oil had only 13% of the radioactivity originally present, mainly in the form of dichlorvos, dimethyl and monomethyl phosphate in addition to desmethyl dichlorvos in oil with aged residues

Efeito residual do lodo de esgoto na produtividade do milho safrinha Residual effect of sewage sludge on off-season corn yield

Directory of Open Access Journals (Sweden)

Graziela Moraes de Cesare Barbosa

2007-06-01

Full Text Available Das opções de disposição final do lodo de esgoto, a reciclagem agrícola tem sido uma das mais utilizadas em diversos países desenvolvidos, sendo considerada a forma mais adequada em termos técnicos, econômicos e ambientais. Este trabalho teve por objetivo avaliar o efeito residual do lodo de esgoto na produtividade do milho safrinha, após dois anos de aplicação consecutiva desse resíduo em um Latossolo Vermelho eutroférrico. O experimento foi realizado em campo, em delineamento em blocos ao acaso com três repetições, e os tratamentos foram os seguintes: testemunha e adubações com lodo de esgoto nas doses de 6, 12, 24 e 36 t ha-1 (peso de matéria seca. Houve efeito residual do uso do lodo de esgoto caleado na produtividade de milho safrinha; a dose de 36 t ha-1 foi estatisticamente superior às doses de 6 e 12 t ha-1.Among the possibilities of final disposal of sewage sludge, agricultural recycling has become one of the most widely used in several developed countries, and is considered the most appropriate in technical, economical and environmental terms. This study aimed at evaluating the sewage sludge residual effect on off-season corn yield on an Eutroferric Red Latossol (Oxisol. The field experiment was in a randomized block design with three replications, with treatments consisting of increasing doses of sewage sludge (0, 6, 12, 24 and 36 t ha-1, on a dry weight basis, applied in the two previous cropping seasons.. The residual effect of the application of lime-stabilized sewage sludge increased the yield of off-season corn; the grain yield under a rate of 36 t ha-1 was statistically higher than those under 6 and 12 t ha-1.

Effect of Applied Stress and Temperature on Residual Stresses Induced by Peening Surface Treatments in Alloy 600

Science.gov (United States)

Telang, A.; Gnäupel-Herold, T.; Gill, A.; Vasudevan, V. K.

2018-04-01

In this study, the effects of applied tensile stress and temperature on laser shock peening (LSP) and cavitation shotless peening (CSP)-induced compressive residual stresses were investigated using neutron and x-ray diffraction. Residual stresses on the surface, measured in situ, were lower than the applied stress in LSP- and CSP-treated Alloy 600 samples (2 mm thick). The residual stress averaged over the volume was similar to the applied stress. Compressive residual stresses on the surface and balancing tensile stresses in the interior relax differently due to hardening induced by LSP. Ex situ residual stress measurements, using XRD, show that residual stresses relaxed as the applied stress exceeded the yield strength of the LSP- and CSP-treated Alloy 600. Compressive residual stresses induced by CSP and LSP decreased by 15-25% in magnitude, respectively, on exposure to 250-450 °C for more than 500 h with 10-11% of relaxation occurring in the first few hours. Further, 80% of the compressive residual stresses induced by LSP and CSP treatments in Alloy 600 were retained even after long-term aging at 350 °C for 2400 h.

Quadratic residues and non-residues selected topics

CERN Document Server

Wright, Steve

2016-01-01

This book offers an account of the classical theory of quadratic residues and non-residues with the goal of using that theory as a lens through which to view the development of some of the fundamental methods employed in modern elementary, algebraic, and analytic number theory. The first three chapters present some basic facts and the history of quadratic residues and non-residues and discuss various proofs of the Law of Quadratic Reciprosity in depth, with an emphasis on the six proofs that Gauss published. The remaining seven chapters explore some interesting applications of the Law of Quadratic Reciprocity, prove some results concerning the distribution and arithmetic structure of quadratic residues and non-residues, provide a detailed proof of Dirichlet’s Class-Number Formula, and discuss the question of whether quadratic residues are randomly distributed. The text is a valuable resource for graduate and advanced undergraduate students as well as for mathematicians interested in number theory.

Fractionation of Uranium Forms as Affected by Spiked Soil Treatment and Soil Type

International Nuclear Information System (INIS)

Lotfy, S.M.; Mostafa, A.Z.; Abdel-Sabour, M.F.

2012-01-01

In a fractionation experiment Uranium forms were compared in two soil types (Mostorud and Elgabalelasfar soil). Also, the variation of U forms due to soil treatment (spiking) were studied. In case of Mostorud soil the initial U - fractions were 45.63 % as residual form, 20.69 % organically bound 16.36 % Mn and Fe oxides bound, 9.76% Carbonate form, 7.41 % exchangeable fractions and 0.15% water soluble fractions. These fractions varied significantly when the soil was spiked with 200 mg U/Kg soil to 46.88 %, 23.19 %, 9.97 %, 16.07 %, 3.79% and 0.10% for residual, organically, Mn- Fe oxide, carbonate, exchangeable and water soluble fractions respectively. These result showed significant reduction in U-ex fraction forms and Mn- Fe bound forms with significant increase in U- carbonate form due to U application. In case of Elgabalelasfar soil, the main U - fractions were 57.42% as residual form (relatively higher residual - U form in the clayey soil) 16.10 % organically bound, 13.78% Mn and Fe oxides bound, 7.22 % Carbonate form, 5.23 % exchangeable fractions and 0.25 % water soluble fractions The application of 200 mg U/Kg soil resulted in a significant changes in U - Fractions distribution as follows : 59.26 % , 11.27 % , 19.59 % , 6.84 % , 2.90 % and 0.14 % for residual , organic , Mn- Fe oxides , carbonate, exchangeable and water soluble fractions , respectively.

Effect of substrate preheating temperature and coating thickness on residual stress in plasma sprayed hydroxyapatite coating

International Nuclear Information System (INIS)

Tang, Dapei

2015-01-01

A thermal-mechanical coupling model was developed based on thermal-elastic- plastic theory according the special process of plasma spraying Hydroxyapatite (HA) coating upon Ti-6Al-4V substrate. On the one hand, the classical Fourier transient heat conduction equation was modified by introducing the effect item of deformation on temperature, on the other hand, the Johnson-Cook model, suitable for high temperature and high strain rate conditions, was used as constitutive equation after considering temperature softening effect, strain hardening effect and strain rate reinforcement effect. Based on the above coupling model, the residual stress field within the HA coating was simulated by using finite element method (FEM). Meanwhile, the substrate preheating temperature and coating thickness on the influence of residual stress components were calculated, respectively. The failure modes of coating were also preliminary analyzed. In addition, in order to verify the reliability of calculation, the material removal measurement technique was applied to determine the residual stress of HA coating near the interface. Some important conclusions are obtained. (paper)

Mineral CO2 sequestration in alkaline solid residues

International Nuclear Information System (INIS)

Huijgen, W.J.J.; Comans, R.N.J.; Witkamp, G.J.

2004-12-01

Mineral carbonation is a promising sequestration route for the permanent and safe storage of carbon dioxide. In addition to calcium- or magnesium-containing primary minerals, suitable alkaline solid residues can be used as feedstock. The use of alkaline residues has several advantages, such as their availability close to CO2 sources and their higher reactivity for carbonation than primary minerals. In addition, the environmental quality of residues can potentially be improved by carbonation. In this study, key factors of the mineral CO2 sequestration process are identified, their influence on the carbonation process is examined, and environmental properties of the reaction products with regard to their possible beneficial utilization are investigated. The use of alkaline solid residues forms a potentially attractive alternative for the first mineral sequestration plants

Differential residual effects of zaleplon and zopiclone on actual driving: a comparison with a low dose of alcohol.

Science.gov (United States)

Vermeeren, Annemiek; Riedel, Wim J; van Boxtel, Martin P J; Darwish, Mona; Paty, Isabelle; Patat, Alain

2002-03-15

To compare residual effects of zaleplon 10 mg, zopiclone 7.5 mg, and placebo, and a social dose of alcohol on car driving, memory, and psychomotor performance. Two-part placebo controlled, crossover study. Part 1 was single blind, Part 2 double blind. University research institute. Thirty healthy volunteers (15 men and 15 women, mean age 32 +/- 7 years) In Part 1 alcohol and alcohol-placebo drinks were administered around noon. In Part 2 single oral doses of zaleplon 10 mg, zopiclone 7.5 mg and placebo were administered at bedtime. A highway driving test, laboratory tests of word learning, critical tracking and divided attention, and subjective assessments of sleep, mood, and effects of treatments on driving. Driving started 40 minutes after a second alcohol dose in Part 1, and 10 hours after drug intake in Part 2. The results demonstrated that alcohol, at average plasma concentrations of approximately 0.030 g/dl, significantly impaired performance in all tests. Zaleplon's residual effects did not differ significantly from those of placebo in any test. In contrast, zopiclone had significant residual effects on driving, divided attention, and memory. The magnitude of impairment in the driving test observed the morning after zopiclone 7.5 mg was twice that observed with alcohol. Zaleplon 10 mg has no residual effects on driving when taken at bedtime, 10 hours before driving. In contrast, zopiclone 7.5 mg can cause marked residual impairment. Patients should be advised to avoid driving the morning after zopiclone administration.

Electroacoustic isoelectric point determinations of bauxite refinery residues: different neutralization techniques and minor mineral effects.

Science.gov (United States)

Freire, Tiago S S; Clark, Malcolm W; Comarmond, M Josick; Payne, Timothy E; Reichelt-Brushett, Amanda J; Thorogood, Gordon J

2012-08-14

Bauxite refinery residue (BRR) is a highly caustic, iron hydroxide-rich byproduct from alumina production. Some chemical treatments of BRR reduce soluble alkalinity and lower residue pH (to values work shows that minor mineral components in complex mineral systems may have a disproportionate effect on the observable bulk IEP. Furthermore, this work shows the appropriateness of electroacoustic techniques in investigating samples with significant soluble mineral components (e.g., ANC).

Effect of irradiation on oxytetracycline residues in poultry meat

Energy Technology Data Exchange (ETDEWEB)

Mazurowski, P [Warsaw Agricultural University, Faculty of Veterinary Medicine, Department of Food Hygiene, Warsaw (Poland)

1994-12-31

The purpose of the study was an evaluation of the effect of ionizing radiation on detection of oxytetracycline residues in poultry meat. Oxytetracycline was chosen as a representative of tetracyclines which are often applied in poultry for therapeutical reasons. The experiment was conducted using both broiler meat treated by oxytetracycline and slurry of broiler meat containing appropriate concentration of this antibiotic. A traditional microbiological method for determination of antibiotics antimicrobial activity was used. A significant decrease of oxytetracycline concentration in meat slurry as a result of irradiation was noted. A dose of 1 kGy reduced concentration of tetracycline to ca 40% and a dose of 3 kGy reduced it to ca 3%. In ground poultry meat a dose of 1 kGy reduced this antibiotic concentration to 70%, a dose of 3 kGy reduced oxytetracycline concentration to 35% and a 5 kGy dose reduced it up to ca 18% of initial concentration. It can be concluded that irradiation of poultry meat with radurization doses can cause some difficulties in detection of tetracycline residues in meat using traditional microbiological methods of detection. (author).

Effect of irradiation on oxytetracycline residues in poultry meat

International Nuclear Information System (INIS)

Mazurowski, P.

1994-01-01

The purpose of the study was an evaluation of the effect of ionizing radiation on detection of oxytetracycline residues in poultry meat. Oxytetracycline was chosen as a representative of tetracyclines which are often applied in poultry for therapeutical reasons. The experiment was conducted using both broiler meat treated by oxytetracycline and slurry of broiler meat containing appropriate concentration of this antibiotic. A traditional microbiological method for determination of antibiotics antimicrobial activity was used. A significant decrease of oxytetracycline concentration in meat slurry as a result of irradiation was noted. A dose of 1 kGy reduced concentration of tetracycline to ca 40% and a dose of 3 kGy reduced it to ca 3%. In ground poultry meat a dose of 1 kGy reduced this antibiotic concentration to 70%, a dose of 3 kGy reduced oxytetracycline concentration to 35% and a 5 kGy dose reduced it up to ca 18% of initial concentration. It can be concluded that irradiation of poultry meat with radurization doses can cause some difficulties in detection of tetracycline residues in meat using traditional microbiological methods of detection. (author)

Hygiene Aspects of the Biogas Process with Emphasis on Spore-Forming Bacteria

Energy Technology Data Exchange (ETDEWEB)

Bagge, Elisabeth

2009-07-01

Biogas is a renewable source of energy which can be obtained from processing of biowaste. The digested residues can be used as fertiliser. Biowaste intended for biogas production contains pathogenic micro-organisms. A pre-pasteurisation step at 70 deg C for 60 min before anaerobic digestion reduces non spore-forming bacteria such as Salmonella spp. To maintain the standard of the digested residues it must be handled in a strictly hygienic manner to avoid recontamination and re-growth of bacteria. The risk of contamination is particularly high when digested residues are transported in the same vehicles as the raw material. However, heat treatment at 70 deg C for 60 min will not reduce spore-forming bacteria such as Bacillus spp. and Clostridium spp. Spore-forming bacteria, including those that cause serious diseases, can be present in substrate intended for biogas production. The number of species and the quantity of Bacillus spp. and Clostridium spp. in manure, slaughterhouse waste and in samples from different stages during the biogas process were investigated. The number of species of clostridia seemed to decrease following digestion, likewise the quantity. However, Bacillus spp. seemed to pass unaffected through the biogas process. In laboratory-scale experiments the effects on clostridia during pasteurisation and digestion were investigated. Pathogenic clostridia were inoculated in substrates from homogenisation tanks and digester tanks. The inoculated clostridia remained after pasteurisation, but the impacts of digestion differ between different species. Culture followed by identification of C. chauvoei by PCR in samples from cattle died from blackleg, is faster and safer than culture followed by biochemical identification of C. chauvoei. However, for environmental samples the PCR method is not practically applicable for detection of C. chauvoei. To avoid spreading of diseases via biogas plants when digested residues are spread on arable land, a pasteurisation

Log bioassay of residual effectiveness of insecticides against bark beetles

Science.gov (United States)

Richard H. Smith

1982-01-01

Residual effectiveness of nine insecticides applied to bark was tested against western, mountain, and Jeffrey pine beetles. Ponderosa and Jeffrey pine trees were treated and logs cut from them 2 to 13 months later, and bioassayed with the three beetles. The insecticides were sprayed at the rate of 1 gal (3.8 l) per 40- or 80-ft² (3.6 or 7.2 m²) bark surface at varying...

Total effects of contact and residual exposure of bifenthrin and λ-cyhalothrin on the predatory mite Galendromus occidentalis (Acari: Phytoseiidae).

Science.gov (United States)

Hamby, Kelly A; Alifano, Jesse A; Zalom, Frank G

2013-10-01

Pyrethroid insecticides are generally regarded as acutely toxic to predatory phytoseiid mites; however, persistence of hull split spray pyrethroid residues on almond trees and their effects on phytoseiids have not been quantified over time. Hull split, the separation of the almond hull along the suture, exposes the new crop nuts to infestation by Amyelois transitella (Walker) larvae, and is the preferred timing for insecticides applied for their control. Galendromus occidentalis (Nesbitt) is the most important phytoseiid biocontrol agent for web-spinning spider mites in California (USA) almond orchards, and the impact of bifenthrin and λ-cyhalothrin pyrethroid residue on their survival, fertility, and fecundity was determined. The total effects of direct contact with esfenvalerate, permethrin, bifenthrin and λ-cyhalothrin were also evaluated for comparison. The total effects (E) of direct contact treatments of the four pyrethroids ranged from 77.8 % for esfenvalerate to 98.8 % for bifenthrin. Both bifenthrin and λ-cyhalothrin twig residue would be considered harmful (IOBC class 4) following field application at hull split timing. Bifenthrin twig residue would be considered slightly harmful (IOBC class 2) for up to 3.5 months and harmless (IOBC class 1) after 6 months. λ-cyhalothrin residue would be considered moderately harmful (IOBC class 3) for up to 3.5 months following application and harmless (IOBC class 1) after 6 months. Bifenthrin and λ-cyhalothrin twig residue on treated trees significantly reduced G. occidentalis female survival for up to 6 months post-treatment, however total effects (E) classify these residues as harmless (IOBC class 1) after 6 months. Harmful effects of direct and residual exposure following application have implications for the use of these pyrethroids in an integrated mite management program for perennial crops.

Chaperone-like activity of β-casein and its effect on residual in vitro activity of horseradish peroxidase

DEFF Research Database (Denmark)

Sulewska, Anna Maria; Olsen, Karsten; Sørensen, Jens Christian

2014-01-01

, as similar experiment with bovine serum albumin resulted in residual activity of horseradish peroxidase that was significantly lower than without any addition. The effect of β-casein on HRP disappears when pH is below the isoelectric point of β-casein. It was also proven by light scattering studies that β...... proteins. Incubating HRP (0.1 mg mL-1) for 10 min at 72 °C resulted in residual activity of 59 ± 5%, while addition of 1 mg mL-1 β-casein resulted in increase in residual activity up to 85 ± 1%. Increased residual activity is not merely attributed to an effect of higher total protein concentration......-casein interacts with horseradish peroxidase when the temperature was increased from 25 to 70 °C whereas interactions seem to cease when temperature was lowered back to 25 °C. This study highlights how specific proteins can influence enzyme activity, which is of potential importance for various industries...

Residual stress effects on the K parameter of the fracture mechanics

International Nuclear Information System (INIS)

Soares, Maria da Conceiccao B. Vieira; Andrade, Arnaldo H. Paes de

1996-01-01

Compressive residual stresses are beneficial and improve resistance to fracture and crack growth. Residual stresses can be introduced in fabricated components by a variety of means and a number of methods such as laser surface treatment, cold expanded hole, and shot peening. Neutrons diffraction measurements of residual stress were performed at a pulsed neutron source (ISIS, Didcot, UK), on shot peened plates of nickel base superalloy Udimet 720 and titanium alloy IMI 834. The stress intensity factor (K) of residual stress was evaluated by finite element modeling and weight function method. Finite element modeling of a 2D plate with a single edge-notch was applied and, due to symmetry only half of the plate was actually modeled. The stress intensity factor (K) was evaluated for both case of remote tension stress and residual stress. Crack surface overlapping, which is physically unacceptable, was noted for small cracks under residual and boundary lading. Overlap correction was proposed and applied in order to obtain reliable values for (K). (author)

Effects of food processing on pesticide residues in fruits and vegetables: a meta-analysis approach.

Science.gov (United States)

Keikotlhaile, B M; Spanoghe, P; Steurbaut, W

2010-01-01

Pesticides are widely used in food production to increase food security despite the fact that they can have negative health effects on consumers. Pesticide residues have been found in various fruits and vegetables; both raw and processed. One of the most common routes of pesticide exposure in consumers is via food consumption. Most foods are consumed after passing through various culinary and processing treatments. A few literature reviews have indicated the general trend of reduction or concentration of pesticide residues by certain methods of food processing for a particular active ingredient. However, no review has focused on combining the obtained results from different studies on different active ingredients with differences in experimental designs, analysts and analysis equipment. In this paper, we present a meta-analysis of response ratios as a possible method of combining and quantifying effects of food processing on pesticide residue levels. Reduction of residue levels was indicated by blanching, boiling, canning, frying, juicing, peeling and washing of fruits and vegetables with an average response ratio ranging from 0.10 to 0.82. Baking, boiling, canning and juicing indicated both reduction and increases for the 95% and 99.5% confidence intervals. Copyright 2009 Elsevier Ltd. All rights reserved.

The Effect of Washing and Peeling on Reduction of Dithiocarbamates Residues in Cucumber and Tomato

Directory of Open Access Journals (Sweden)

Mohammad Reza Mehrasebi

2016-03-01

Full Text Available Background: Dithiocarbamates, the main group of fungicides, are used to control about 400 pathogens in more than 70 crops. These pesticides are widely applied to crops including potato, cereal, apple, pear and leafy vegetables throughout the world since 1960. From the late 1980s, using these fungicides has caused much debate among regulators about their long-term effects on consumers and occupational users. Method: In this study the residues of Dithiocarbamates in cucumber and tomato using the colorimetric method (Keppel method was measured. Respectively 80 and 45 samples of greenhouse cucumber and tomato were collected from Zanjan vegetables center in autumns and winter 2013. The samples were analyzed in 4 treatments of: unwashed, washing with water, washing whit detergent and peeling. Result: The results showed that the average concentration of Dithiocarbamates residues in unwashed greenhouse cucumber and tomatoes were 384.5 µg/kg and 65 µg/kg respectively. 35% and 5% of unwashed and water washed cucumber and tomato samples (respectively had higher Dithiocarbamates residue than MRL recommended by Institute of Standards and Industrial Research of Iran (0.5mg/kg. Conclusion: The treatments of washing and peeling had significant effect on the reduction of Dithiocarbamates residues in the all samples.

Studies on residue-free decontaminants for chemical warfare agents.

Science.gov (United States)

Wagner, George W

2015-03-17

Residue-free decontaminants based on hydrogen peroxide, which decomposes to water and oxygen in the environment, are examined as decontaminants for chemical warfare agents (CWA). For the apparent special case of CWA on concrete, H2O2 alone, without any additives, effectively decontaminates S-2-(diisopropylamino)ethyl O-ethyl methylphosphonothioate (VX), pinacolyl methylphosphorofluoridate (GD), and bis(2-choroethyl) sulfide (HD) in a process thought to involve H2O2 activation by surface-bound carbonates/bicarbonates (known H2O2 activators for CWA decontamination). A plethora of products are formed during the H2O2 decontamination of HD on concrete, and these are characterized by comparison to synthesized authentic compounds. As a potential residue-free decontaminant for surfaces other than concrete (or those lacking adsorbed carbonate/bicarbonate) H2O2 activation for CWA decontamination is feasible using residue-free NH3 and CO2 as demonstrated by reaction studies for VX, GD, and HD in homogeneous solution. Although H2O2/NH3/CO2 ("HPAC") decontaminants are active for CWA decontamination in solution, they require testing on actual surfaces of interest to assess their true efficacy for surface decontamination.

Plant residues--a low cost, effective bioremediation treatment for petrogenic hydrocarbon-contaminated soil.

Science.gov (United States)

Shahsavari, Esmaeil; Adetutu, Eric M; Anderson, Peter A; Ball, Andrew S

2013-01-15

Petrogenic hydrocarbons represent the most commonly reported environmental contaminant in industrialised countries. In terms of remediating petrogenic contaminated hydrocarbons, finding sustainable non-invasive technologies represents an important goal. In this study, the effect of 4 types of plant residues on the bioremediation of aliphatic hydrocarbons was investigated in a 90 day greenhouse experiment. The results showed that contaminated soil amended with different plant residues led to statistically significant increases in the utilisation rate of Total Petroleum Hydrocarbon (TPH) relative to control values. The maximum TPH reduction (up to 83% or 6800 mg kg(-1)) occurred in soil mixed with pea straw, compared to a TPH reduction of 57% (4633 mg kg(-1)) in control soil. A positive correlation (0.75) between TPH reduction rate and the population of hydrocarbon-utilising microorganisms was observed; a weaker correlation (0.68) was seen between TPH degradation and bacterial population, confirming that adding plant materials significantly enhanced both hydrocarbonoclastic and general microbial soil activities. Microbial community analysis using Denaturing Gradient Gel Electrophoresis (DGGE) showed that amending the contaminated soil with plant residues (e.g., pea straw) caused changes in the soil microbial structure, as observed using the Shannon diversity index; the diversity index increased in amended treatments, suggesting that microorganisms present on the dead biomass may become important members of the microbial community. In terms of specific hydrocarbonoclastic activity, the number of alkB gene copies in the soil microbial community increased about 300-fold when plant residues were added to contaminated soil. This study has shown that plant residues stimulate TPH degradation in contaminated soil through stimulation and perhaps addition to the pool of hydrocarbon-utilising microorganisms, resulting in a changed microbial structure and increased alkB gene

Effects of distance from center of a weld to fixed end on residual stress and stress intensity factor of a piping weld. Evaluation of SCC growth under residual stress field. Report 1

International Nuclear Information System (INIS)

Miyazaki, Katsumasa; Numata, Masanori; Saito, Koichi; Mochizuki, Masahito

2006-01-01

The fixed conditions of butt welds between straight pipe and valve or pump in the actual piping system are different from those of straight pipes. However, the effect of fixed condition on the residual stress and the stress intensity factor for evaluation of structural integrity of cracked piping was not clear. In this study, the finite element analyses were conducted by considering the differences in the distance from the center of weld to the fixed end L to clarify the effect of fixed condition on the residual stress and the stress intensity factor. For the 600 A piping, the axial residual stress distribution was not affected by the distance L. Furthermore, the stress intensity factor of circumferential crack under the residual stress field with fixed condition could be estimated by using the existing simplified solution for piping. (author)

Characterization of Active Site Residues of Nitroalkane Oxidase†

Science.gov (United States)

Valley, Michael P.; Fenny, Nana S.; Ali, Shah R.; Fitzpatrick, Paul F.

2010-01-01

The flavoenzyme nitroalkane oxidase catalyzes the oxidation of primary and secondary nitrolkanes to the corresponding aldehydes and ketones plus nitrite. The structure of the enzyme shows that Serl71 forms a hydrogen bond to the flavin N5, suggesting that it plays a role in catalysis. Cys397 and Tyr398 were previously identified by chemical modification as potential active site residues. To more directly probe the roles of these residues, the S171A, S171V, S171T, C397S, and Y398F enzymes have been characterized with nitroethane as substrate. The C397S and Y398 enzymes were less stable than the wild-type enzyme, and the C397S enzyme routinely contained a substoichiometric amount of FAD. Analysis of the steady-state kinetic parameters for the mutant enzymes, including deuterium isotope effects, establishes that all of the mutations result in decreases in the rate constants for removal of the substrate proton by ~5-fold and decreases in the rate constant for product release of ~2-fold. Only the S171V and S171T mutations alter the rate constant for flavin oxidation. These results establish that these residues are not involved in catalysis, but rather are required for maintaining the protein structure. PMID:20056514

The effects of machine parameters on residual stress determined using micro-Raman spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Sparks, R.G.; Enloe, W.S.; Paesler, M.A.

1988-12-01

The effects of machine parameters on residual stresses in single point diamond turned silicon and germanium have been investigated using micro-Raman spectroscopy. Residual stresses were sampled across ductile feed cuts in < 100 > silicon and germanium which were single point diamond turned using a variety of feed rates, rake angles and clearance angles. High spatial resolution micro-Raman spectra (1{mu}m spot) were obtained in regions of ductile cutting where no visible surface damage was present. The use of both 514-5nm and 488.0nm excitation wavelengths, by virtue of their differing characteristic penetration depths in the materials, allowed determinations of stress profiles as a function of depth into the sample. Previous discussions have demonstrated that such Raman spectra will exhibit asymmetrically broadened peaks which are characteristic of the superposition of a continuum of Raman scatterers from the various depths probed. Depth profiles of residual stress were obtained using computer deconvolution of the resulting asymmetrically broadened raman spectra.

Model-checking techniques based on cumulative residuals.

Science.gov (United States)

Lin, D Y; Wei, L J; Ying, Z

2002-03-01

Residuals have long been used for graphical and numerical examinations of the adequacy of regression models. Conventional residual analysis based on the plots of raw residuals or their smoothed curves is highly subjective, whereas most numerical goodness-of-fit tests provide little information about the nature of model misspecification. In this paper, we develop objective and informative model-checking techniques by taking the cumulative sums of residuals over certain coordinates (e.g., covariates or fitted values) or by considering some related aggregates of residuals, such as moving sums and moving averages. For a variety of statistical models and data structures, including generalized linear models with independent or dependent observations, the distributions of these stochastic processes tinder the assumed model can be approximated by the distributions of certain zero-mean Gaussian processes whose realizations can be easily generated by computer simulation. Each observed process can then be compared, both graphically and numerically, with a number of realizations from the Gaussian process. Such comparisons enable one to assess objectively whether a trend seen in a residual plot reflects model misspecification or natural variation. The proposed techniques are particularly useful in checking the functional form of a covariate and the link function. Illustrations with several medical studies are provided.

Effect of crop sequence and crop residues on soil C, soil N and yield of maize

International Nuclear Information System (INIS)

Shafi, M.; Bakht, J.; Attaullah; Khan, M.A.

2010-01-01

Improved management of nitrogen (N) in low N soils is critical for increased soil productivity and crop sustainability. The objective of the present study was to evaluate the effects of residues incorporation, residues retention on soil surface as mulch, fertilizer N and legumes in crop rotation on soil fertility and yield of maize (Zea may L.). Fertilizer N was applied to maize at the rate of 160 kg ha/sup -1/, and to wheat at the rate of 120 kg ha/sup -1/ or no fertilizer N application. Crop rotation with the sequence of maize after wheat (Triticum aestivum L.), maize after lentil (Lens culinaris Medic) or wheat after mash bean (Vigna mungo L.) arranged in a split plot design was followed. Post-harvest incorporation of crop residues and residues retention on soil surface as mulch had significantly (p=0.05) affected grain and stover yield during 2004 and 2005. Two years average data revealed that grain yield was increased by 3.31 and 6.72% due to mulch and residues incorporation. Similarly, stover yield was also enhanced by 5.39 and 10.27% due to the same treatment respectively. Mulch and residues incorporation also improved stover N uptake by 2.23 and 6.58%, respectively. Total soil N and organic matter was non significantly (p=0.05) increased by 5.63 and 2.38% due to mulch and 4.13, 7.75% because of crop residues incorporation in the soil. Maize grain and stover yield responded significantly (p=0.05) to the previous legume (lentil) crop when compared with the previous cereal crop (wheat). The treatment of lentil - maize(+N), on the average, increased grain yield of maize by 15.35%, stover yield by 16.84%, total soil N by 10.31% and organic matter by 10.17%. Similarly, fertilizer N applied to the previous wheat showed carry over effect on grain yield (6.82%) and stover yield (11.37%) of the following maize crop. The present study suggested that retention of residues on soil surface as mulch, incorporation of residues in soil and legume (lentil - maize) rotation

Report of the Task Force on Sawmill Wood Residue Management

International Nuclear Information System (INIS)

1993-11-01

The Sawmill Wood Residue Task Force was established in 1993 to seek solutions to managing wood residue at sawmills, shingle mills, and log sort yards in British Columbia without burning or landfilling. In particular, the Task Force was formed to address the phaseout of beehive-type wood waste burners by January 1, 1996. The Task Force was formed at the forest product industry's request and included representatives from industry associations and government. It reviewed existing information on the quantities of mill residues and the options available for reducing, reusing, and recycling the residues. Nearly half of all the province's residues of 5 million bone dry tonnes/y is disposed of by burning with no energy recovery, or by landfilling. It was recognized that the total volume of wood residue cannot be handled by any one method suitable for all sources but that in the near term, electricity generation could deal with a significant percentage of wood currently being burned. The most immediate technically viable opportnity by industry in this area may be in cogeneration of electricity for load displacement at pulp mills. Other opportunities exist such as conversion of wood residue to liquid fuels but these require greater commitments to research and development. The need to handle bark and sawdust was identified as a critical requirement for alternate uses. Small niche uses for wood residue must be examined on a case by case basis for each company or group of companies in a region. The provincial government can also promote better use of wood wastes through policies such as social costing of power generation options and sales tax exemption for ethanol fuel. 1 tab

Effect of routine preoperative fasting on residual gastric volume and ...

African Journals Online (AJOL)

2016-02-10

Feb 10, 2016 ... Key words: Fasting, myomectomy, pH, residual gastric volume. Date of Acceptance: ... gastric volume and acid in patients undergoing myomectomy. Niger J Clin ..... of gastric residual volume: A simulated, controlled study.

Leptogenesis and residual CP symmetry

International Nuclear Information System (INIS)

Chen, Peng; Ding, Gui-Jun; King, Stephen F.

2016-01-01

We discuss flavour dependent leptogenesis in the framework of lepton flavour models based on discrete flavour and CP symmetries applied to the type-I seesaw model. Working in the flavour basis, we analyse the case of two general residual CP symmetries in the neutrino sector, which corresponds to all possible semi-direct models based on a preserved Z 2 in the neutrino sector, together with a CP symmetry, which constrains the PMNS matrix up to a single free parameter which may be fixed by the reactor angle. We systematically study and classify this case for all possible residual CP symmetries, and show that the R-matrix is tightly constrained up to a single free parameter, with only certain forms being consistent with successful leptogenesis, leading to possible connections between leptogenesis and PMNS parameters. The formalism is completely general in the sense that the two residual CP symmetries could result from any high energy discrete flavour theory which respects any CP symmetry. As a simple example, we apply the formalism to a high energy S 4 flavour symmetry with a generalized CP symmetry, broken to two residual CP symmetries in the neutrino sector, recovering familiar results for PMNS predictions, together with new results for flavour dependent leptogenesis.

Effective sorption of atrazine by biochar colloids and residues derived from different pyrolysis temperatures.

Science.gov (United States)

Yang, Fan; Gao, Yan; Sun, Lili; Zhang, Shuaishuai; Li, Jiaojiao; Zhang, Ying

2018-04-26

Biochar has attracted much attention, which owns many environmental and agronomic benefits, including carbon sequestration, improvement of soil quality, and immobilization of environmental contaminants. Biochar has been also investigated as an effective sorbent in recent publications. Generally, biochar particles can be divided into colloids and residues according to particle sizes, while understanding of adsorption capacities towards organic pollutants in each section is largely unknown, representing a critical knowledge gap in evaluations on the effectiveness of biochar for water treatment application. Scanning electron microscopy (SEM) images, X-ray diffraction (XRD), Raman spectra, Fourier-transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), and Brunauer-Emmett-Teller (BET) method are used to examine the structures and surface properties of biochar colloids and residues derived from corn straws prepared at different pyrolysis temperatures. Also, their roles in atrazine (a typical organic pollutant) removal are investigated by batch adsorption experiments and fitted by different kinetic and thermodynamic models, respectively. The adsorption capacities of biochar colloids are much more than those of residues, resulting from the colloids containing abundant oxygen functional groups and mineral substances, and the adsorption capacities of biochar colloids and residues increase with the increase of pyrolysis temperatures. The highest adsorption performance of 139.33 mg g -1 can be obtained in biochar colloids prepared at 700 °C, suggesting the important functions of biochar colloids in the application of atrazine removal by biochar.

Effect of an absorbent overlay on the residual stress field induced by laser shock processing on aluminum samples

International Nuclear Information System (INIS)

Rubio-Gonzalez, C.; Gomez-Rosas, G.; Ocana, J.L.; Molpeceres, C.; Banderas, A.; Porro, J.; Morales, M.

2006-01-01

Laser shock processing (LSP) or laser shock peening is a new technique for strengthening metals. This process induces a compressive residual stress field, which increases fatigue crack initiation life and reduces fatigue crack growth rate. Specimens of 6061-T6 aluminum alloy are used in this investigation. A convergent lens is used to deliver 2.5 J, 8 ns laser pulses by a Q-switch Nd:YAG laser, operating at 10 Hz. The pulses are focused to a diameter of 1.5 mm onto aluminum samples. Density of 2500 pulses/cm 2 with infrared (1064 nm) radiation was used. The effect of an absorbent overlay on the residual stress field using this LSP setup and this energy level is evaluated. Residual stress distribution as a function of depth is assessed by the hole drilling method. It is observed that the overlay makes the compressive residual stress profile move to the surface. This effect is explained on the basis of the vaporization of the coat layer suppressing thermal effects on the metallic substrate. The effect of coating the specimen surface before LSP treatment may have advantages on improving wear and contact fatigue properties of this aluminum alloy

Residual stress control and design of next-generation ultra-hard gear steels

Science.gov (United States)

Qian, Yana

In high power density transmission systems, Ni-Co secondary hardening steels have shown great potential for next-generation gear applications due to their excellent strength, toughness and superior fatigue performance. Study of residual stress generation and evolution in Ferrium C61 and C67 gear steels revealed that shot peening and laser peening processes effectively produce desired beneficial residual stress in the steels for enhanced fatigue performance. Surface residual stress levels of -1.4GPa and -1.5GPa were achieved in shot peened C61 and laser peened C67, respectively, without introducing large surface roughness or defects. Higher compressive residual stress is expected in C67 according to a demonstrated correlation between attainable residual stress and material hardness. Due to the lack of appropriate shot media, dual laser peening is proposed for future peening optimization in C67. A novel non-destructive synchrotron radiation technique was implemented and applied for the first time for residual stress distribution analysis in gear steels with large composition and property gradients. Observed substantial residual stress redistribution and material microstructure change during the rolling contact fatigue screening test with extremely high 5.4GPa load indicates the unsuitability of the test as a fatigue life predictor. To exploit benefits of higher case hardness and associated residual stress, a new material and process (CryoForm70) aiming at 70Rc surface hardness was designed utilizing the systems approach based on thermodynamics and secondary hardening mechanisms. The composition design was first validated by the excellent agreement between experimental and theoretical core martensite start temperature in the prototype. A novel cryogenic deformation process was concurrently designed to increase the case martensite volume fraction from 76% to 92% for enhanced strengthening efficiency and surface hardness. High temperature vacuum carburizing was

Ameliorating effects of industrial sugar residue on the Jales gold mine spoil (NE Portugal) using Holcus lanatus and Phaseolus vulgaris as indicators

Energy Technology Data Exchange (ETDEWEB)

Bleeker, P.M.; Teiga, P.M.; Santos, M.H.; Koe, T. de; Verkleij, J.A.C

2003-09-01

A residue of the sugar industry can be used in revegetation programs on metal contaminated sites. - Phytostabilisation of bare heavily contaminated substrate, such as abandoned mine sites, is considered a very appropriate technology in order to diminish erosion and dispersion of contaminants into the surroundings. In this short-term pot study, application of industrial sugar residue (ISR), a waste product of the sugar industry, proved to ameliorate spoils conditions for plant performance by elevating pH and immobilising several metals. Although arsenate concentrations were positively correlated to spoil pH and spoil treatment with ISR mobilised As, growth of both Phaseolus vulgaris and Holcus lanatus improved significantly after applications of 3.75 g ISR kg{sup -1} dry spoil. Nutrient uptake from the substrate, with the exception of potassium, was elevated by ISR. As a remediation technique ISR application could be effective although in As-contaminated sites application might be restricted to areas where leaching to (ground) water does not form a risk.

Residual stress determination in oxide layers at different length scales combining Raman spectroscopy and X-ray diffraction: Application to chromia-forming metallic alloys

Science.gov (United States)

Guerain, Mathieu; Grosseau-Poussard, Jean-Luc; Geandier, Guillaume; Panicaud, Benoit; Tamura, Nobumichi; Kunz, Martin; Dejoie, Catherine; Micha, Jean-Sebastien; Thiaudière, Dominique; Goudeau, Philippe

2017-11-01

In oxidizing environments, the protection of metals and alloys against further oxidation at high temperature is provided by the oxide film itself. This protection is efficient only if the formed film adheres well to the metal (substrate), i.e., without microcracks and spalls induced by thermomechanical stresses. In this study, the residual stresses at both macroscopic and microscopic scales in the oxide film adhering to the substrate and over the damaged areas have been rigorously determined on the same samples for both techniques. Ni-30Cr and Fe-47Cr alloys have been oxidized together at 900 and 1000 °C, respectively, to create films with a thickness of a few microns. A multi-scale approach was adopted: macroscopic stress was determined by conventional X-ray diffraction and Raman spectroscopy, while microscopic residual stress mappings were performed over different types of bucklings using Raman micro-spectroscopy and synchrotron micro-diffraction. A very good agreement is found at macro- and microscales between the residual stress values obtained with both techniques, giving confidence on the reliability of the measurements. In addition, relevant structural information at the interface between the metallic substrate and the oxide layer was collected by micro-diffraction, a non-destructive technique that allows mapping through the oxide layer, and both the grain size and the crystallographic orientation of the supporting polycrystalline metal located either under a buckling or not were measured.

Investigation on reusing water treatment residuals to remedy soil contaminated with multiple metals in Baiyin, China

Energy Technology Data Exchange (ETDEWEB)

Wang, Changhui; Zhao, Yuanyuan [The Key Laboratory of Water and Sediment Sciences, Ministry of Education, School of Environment, Beijing Normal University, Beijing 100875 (China); Pei, Yuansheng, E-mail: yspei@bnu.edu.cn [The Key Laboratory of Water and Sediment Sciences, Ministry of Education, School of Environment, Beijing Normal University, Beijing 100875 (China)

2012-10-30

Highlights: Black-Right-Pointing-Pointer Fe/Al water treatment residuals (FARs) can stabilize As, Pb, Ni, Zn, Cr and Cu. Black-Right-Pointing-Pointer FARs cannot stabilize Ba and Cd. Black-Right-Pointing-Pointer The properties of FARs and soil affect the FARs' ability of stabilizing metals. - Abstract: In this work, the remediation of soils contaminated with multiple metals using ferric and alum water treatment residuals (FARs) in Baiyin, China, was investigated. The results of metals fractionation indicated that after the soil was treated with FARs, arsenic (As), lead (Pb), nickel (Ni), zinc (Zn) and copper (Cu) could be transformed into more stable forms, i.e., As bound in crystalline Fe/Al oxides and other metals in the oxidable and residual forms. However, the forms of chromium (Cr) and cadmium (Cd) were unaffected. Interestingly, due to the effect of FARs, barium (Ba) was predominantly transformed into more mobile forms. The bioaccessibility extraction test demonstrated that the FARs reduced the bioaccessibility of As by 25%, followed by Cu, Cr, Zn, Ni and Pb. The bioaccessibility of Cd and Ba were increased; in particular, there was an increase of 41% for Ba at the end of the test. In conclusion, the FARs can be used to remedy soil contaminated with multiple metals, but comprehensive studies are needed before practical applications of this work.

Effect of water content and organic carbon on remote sensing of crop residue cover

Science.gov (United States)

Serbin, G.; Hunt, E. R., Jr.; Daughtry, C. S. T.; McCarty, G. W.; Brown, D. J.; Doraiswamy, P. C.

2009-04-01

Crop residue cover is an important indicator of tillage method. Remote sensing of crop residue cover is an attractive and efficient method when compared with traditional ground-based methods, e.g., the line-point transect or windshield survey. A number of spectral indices have been devised for residue cover estimation. Of these, the most effective are those in the shortwave infrared portion of the spectrum, situated between 1950 and 2500 nm. These indices include the hyperspectral Cellulose Absorption Index (CAI), and advanced multispectral indices, i.e., the Lignin-Cellulose Absorption (LCA) index and the Shortwave Infrared Normalized Difference Residue Index (SINDRI), which were devised for the NASA Terra Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) sensor. Spectra of numerous soils from U.S. Corn Belt (Indiana and Iowa) were acquired under wetness conditions varying from saturation to oven-dry conditions. The behavior of soil reflectance with water content was also dependent on the soil organic carbon content (SOC) of the soils, and the location of the spectral bands relative to significant water absorptions. High-SOC soils showed the least change in spectral index values with increase in soil water content. Low-SOC soils, on the other hand, showed measurable difference. For CAI, low-SOC soils show an initial decrease in index value followed by an increase, due to the way that water content affects CAI spectral bands. Crop residue CAI values decrease with water content. For LCA, water content increases decrease crop residue index values and increase them for soils, resulting in decreased contrast. SINDRI is also affected by SOC and water content. As such, spatial information on the distribution of surface soil water content and SOC, when used in a geographic information system (GIS), will improve the accuracy of remotely-sensed crop residue cover estimates.

Effect of oil refining processes on 14 C-tetrachlorvinphos residues in soya bean oil

International Nuclear Information System (INIS)

Farghaly, M.; Zayed, S.M.A.D.

1986-01-01

Crude soya bean oil extracted from grains treated with 14 C-tetrachlorvinphos and stored for 30 weeks was subjected to different refining processes. The effect of commercial refining processes, namely: alkali treatment, bleaching, winterization and deodorization on the nature and magnitude of the originally present residues was investigated. A high percentage (52%) of the residues was eliminated during alkali neutralization. No potentially toxic materials were detected among the identified degradation products. The obtained data showed that the ultimate degradation products were dimethyl phosphate and mono methyl phosphate.2 tab.,2 scheme

Residual, direct and cumulative effect of zinc application on wheat and rice yield under rice-wheat syst

Directory of Open Access Journals (Sweden)

R. Khan

2009-05-01

Full Text Available Zinc (Zn deficiency is prevalent particularly on calcareous soils of arid and semiarid region. A field experiment was conducted to investigate the direct, residual and cumulative effect of zinc on the yield of wheat and rice in permanent layout for two consecutive years, 2004-05 and 2005-06 at Arid Zone Research Institute D.I. Khan. Soil under study was deficient in Zn (0.8 mg kg-1. Effect of Zn on yield, Zn concentrations in leaf and soils were assessed using wheat variety Naseer-2000 and rice variety IRRI-6. Three rates of Zn, ranging from 0 to 10 kg ha-1 in soil, were applied as zinc sulphate (ZnSO4. 7H2O along with basal dose fertilization of nitrogen, phosphorus and potassium. Mature leaf and soil samples were collected at panicle initiation stage. The results showed that grain yield of wheat and rice was significantly increased by the direct application of 5 and 10 kg Zn ha-1. Highest grain yield of wheat (5467 kg ha-1 was recorded with the direct application of 10 kg Zn ha-1 while 4994 kg ha-1 was recorded with the cumulative application of 10 kg Zn ha-1 but the yield increase due to residual effect of Zn was statistically lower than the cumulative effect of Zn. Maximum paddy yield was recorded with the cumulative application ofZn followed by residual and direct applied 10 and 5 kg Zn kg ha-1, respectively. Zn concentration in soils ranged from 0.3 to 1.5 mg kg-1 in wheat and 0.24 to 2.40 mg kg-1 in rice, while in leaves it ranged from 18-48 mg kg-1 in wheat and 15-52 mg kg-1 in rice. The concentration of Zn in soil and leaves increased due to the treatments in the order; cumulative > residual > direct effect > control (without Zn. The yield attributes like 1000- grain weight, number of spikes, spike length and plant height were increased by the residual, direct and cumulative effect of Zn levels; however, the magnitude of increase was higher in cumulative effect than residual and direct effect of Zn, respectively. Under Zn-deficient soil

Acute effects of high-dose furosemide on residual renal function in CAPD patients

NARCIS (Netherlands)

van Olden, Rudolf W.; Guchelaar, Henk-Jan; Struijk, Dirk G.; Krediet, Raymond T.; Arisz, Lambertus

2003-01-01

BACKGROUND: High doses of furosemide can increase urine volume in chronic peritoneal dialysis (CAPD) patients. However, no information is available about effects on urinary solute excretion in relation to residual glomerular filtration rate (GFR), urinary furosemide excretion, and peritoneal solute

Effect of residual ascorbate on determination of nitrite in commercial cured meat products.

Science.gov (United States)

Fox, J B; Doerr, R C; Gates, R

1984-01-01

Residual ascorbate in cured meat slurries results in different amounts of pigment being produced from different Griess reagent combinations. The phenomenon was used to study residual ascorbate in commercial cured meat products which had a variety of textures, acidities, moisture and meat content, fat, homogeneity, initial nitrite, and processing conditions. Diluting and heating the samples according to the AOAC procedure did not completely eliminate the ascorbate interference, but making the sample alkaline did. Determining nitrite separately in supernate and precipitate from the first dilution showed the effect of heating to be the elimination of interferences and solubilization or extraction of nitrite from the precipitate.

Availability of residual nitrogen from fertilizers in soil

International Nuclear Information System (INIS)

Jakovljevic, M.; Filipovic, R.; Petrovic, M.

1983-01-01

The plant availability of residual fertilizer nitrogen for the next crop was studied in chernozem and pseudogley soils. Release of nitrogen was examined after incubation at 3 and 30 0 C. It was found that the use of increased doses of nitrogen fertilizer (ammonium nitrate) led to an increased release of residual fertilizer nitrogen into plant available forms. The release of this nitrogen fraction was 5-10 times faster in comparison with the remaining soil nitrogen. (author)

Availability of residual nitrogen from fertilizers in soil

Energy Technology Data Exchange (ETDEWEB)

Jakovljevic, M.; Filipovic, R.; Petrovic, M. (Institut za Primeni Nuklearne Energije u Poljoprivedri, Veterinarstvu i Sumarstvu, Zemun (Yugoslavia))

1983-05-01

The plant availability of residual fertilizer nitrogen for the next crop was studied in chernozem and pseudogley soils. Release of nitrogen was examined after incubation at 3 and 30/sup 0/C. It was found that the use of increased doses of nitrogen fertilizer (ammonium nitrate) led to an increased release of residual fertilizer nitrogen into plant available forms. The release of this nitrogen fraction was 5-10 times faster in comparison with the remaining soil nitrogen.

Ink-Jet Printer Forms Solar-Cell Contacts

Science.gov (United States)

Alexander, Paul, Jr.; Vest, R. W.; Binford, Don A.; Tweedell, Eric P.

1988-01-01

Contacts formed in controllable patterns with metal-based inks. System forms upper metal contact patterns on silicon photovoltaic cells. Uses metallo-organic ink, decomposes when heated, leaving behind metallic, electrically conductive residue in printed area.

A Simplified Model for the Effect of Weld-Induced Residual Stresses on the Axial Ultimate Strength of Stiffened Plates

Science.gov (United States)

Chen, Bai-Qiao; Guedes Soares, C.

2018-03-01

The present work investigates the compressive axial ultimate strength of fillet-welded steel-plated ship structures subjected to uniaxial compression, in which the residual stresses in the welded plates are calculated by a thermo-elasto-plastic finite element analysis that is used to fit an idealized model of residual stress distribution. The numerical results of ultimate strength based on the simplified model of residual stress show good agreement with those of various methods including the International Association of Classification Societies (IACS) Common Structural Rules (CSR), leading to the conclusion that the simplified model can be effectively used to represent the distribution of residual stresses in steel-plated structures in a wide range of engineering applications. It is concluded that the widths of the tension zones in the welded plates have a quasi-linear behavior with respect to the plate slenderness. The effect of residual stress on the axial strength of the stiffened plate is analyzed and discussed.

Identification of key amino acid residues modulating intracellular and in vitro microcin E492 amyloid formation

Directory of Open Access Journals (Sweden)

Paulina eAguilera

2016-01-01

Full Text Available Microcin E492 (MccE492 is a pore-forming bacteriocin produced and exported by Klebsiella pneumoniae RYC492. Besides its antibacterial activity, excreted MccE492 can form amyloid fibrils in vivo as well as in vitro. It has been proposed that bacterial amyloids can be functional playing a biological role, and in the particular case of MccE492 it would control the antibacterial activity. MccE492 amyloid fibril’s morphology and formation kinetics in vitro have been well characterized, however it is not known which amino acid residues determine its amyloidogenic propensity, nor if it forms intracellular amyloid inclusions as has been reported for other bacterial amyloids. In this work we found the conditions in which MccE492 forms intracellular amyloids in E. coli cells, that were visualized as round-shaped inclusion bodies recognized by two amyloidophillic probes, 2-4´-methylaminophenyl benzothiazole and thioflavin-S. We used this property to perform a flow cytometry-based assay to evaluate the aggregation propensity of MccE492 mutants, that were designed using an in silico prediction of putative aggregation hotspots. We established that the predicted amino acid residues 54-63, effectively act as a pro-amyloidogenic stretch. As in the case of other amyloidogenic proteins, this region presented two gatekeeper residues (P57 and P59, which disfavor both intracellular and in vitro MccE492 amyloid formation, preventing an uncontrolled aggregation. Mutants in each of these gatekeeper residues showed faster in vitro aggregation and bactericidal inactivation kinetics, and the two mutants were accumulated as dense amyloid inclusions in more than 80% of E. coli cells expressing these variants. In contrast, the MccE492 mutant lacking residues 54-63 showed a significantly lower intracellular aggregation propensity and slower in vitro polymerization kinetics. Electron microscopy analysis of the amyloids formed in vitro by these mutants revealed that, although

Resistance of pathogenic and spoilage microorganisms to disinfectants in the presence of organic matter and their residual effect on stainless steel and polypropylene.

Science.gov (United States)

Iñiguez-Moreno, Maricarmen

2018-04-23

The effectiveness of disinfectants can vary according to the microorganism, type of residues and surface. Hence, the aim of this study was to determine the effectiveness of four disinfectants in the presence of organic matter and their residual effect on stainless steel grade 304 (SS) and polypropylene B (PP-B). The disinfectant effectiveness in the presence of meat extract, yolk egg and whole milk was determined according to AOAC and UNE-EN 1040:2015; the residual effect was realized according to UNE-EN 13697:2015, using approved strains. The disinfectant effectiveness was affect at different grades depending on the organic matter present; disinfectant A (400μgmL -1 , fifth generation quaternary ammonium compound, QAC) was most effective in the presence of 10% meat extract, while the disinfectant C (200μgmL -1 , peracetic acid) had better activity in the presence of 10% egg yolk and whole milk. In the evaluation of residual effect onto SS and PP-B, the QAC had the better effect, reducing 6 Log 10 CFU mL -1 of Listeria monocytogenes ATCC 19111 24h after their application. Conversely, the disinfectants had no residual effect against Pseudomonas aeruginosa ATCC 15442. The antimicrobial activity of disinfectants tested against pathogenic and spoilage microorganisms was affected according to the type of organic matter. Disinfectant A had a more residual effect than the other disinfectants evaluated. Moreover, the residual effect of a disinfectant is greater on SS than on PP-B and dependent on the microorganism tested. Copyright © 2018. Published by Elsevier Ltd.

Determination of GMPE functional form for an active region with limited strong motion data: application to the Himalayan region

Science.gov (United States)

Bajaj, Ketan; Anbazhagan, P.

2018-01-01

Advancement in the seismic networks results in formulation of different functional forms for developing any new ground motion prediction equation (GMPE) for a region. Till date, various guidelines and tools are available for selecting a suitable GMPE for any seismic study area. However, these methods are efficient in quantifying the GMPE but not for determining a proper functional form and capturing the epistemic uncertainty associated with selection of GMPE. In this study, the compatibility of the recent available functional forms for the active region is tested for distance and magnitude scaling. Analysis is carried out by determining the residuals using the recorded and the predicted spectral acceleration values at different periods. Mixed effect regressions are performed on the calculated residuals for determining the intra- and interevent residuals. Additionally, spatial correlation is used in mixed effect regression by changing its likelihood function. Distance scaling and magnitude scaling are respectively examined by studying the trends of intraevent residuals with distance and the trend of the event term with magnitude. Further, these trends are statistically studied for a respective functional form of a ground motion. Additionally, genetic algorithm and Monte Carlo method are used respectively for calculating the hinge point and standard error for magnitude and distance scaling for a newly determined functional form. The whole procedure is applied and tested for the available strong motion data for the Himalayan region. The functional form used for testing are five Himalayan GMPEs, five GMPEs developed under NGA-West 2 project, two from Pan-European, and one from Japan region. It is observed that bilinear functional form with magnitude and distance hinged at 6.5 M w and 300 km respectively is suitable for the Himalayan region. Finally, a new regression coefficient for peak ground acceleration for a suitable functional form that governs the attenuation

Thermodynamic effects of replacements of Pro residues in helix interiors of maltose-binding protein.

Science.gov (United States)

Prajapati, R S; Lingaraju, G M; Bacchawat, Kiran; Surolia, Avadhesha; Varadarajan, Raghavan

2003-12-01

Introduction of Pro residues into helix interiors results in protein destabilization. It is currently unclear if the converse substitution (i.e., replacement of Pro residues that naturally occur in helix interiors would be stabilizing). Maltose-binding protein is a large 370-amino acid protein that contains 21 Pro residues. Of these, three nonconserved residues (P48, P133, and P159) occur at helix interiors. Each of the residues was replaced with Ala and Ser. Stabilities were characterized by differential scanning calorimetry (DSC) as a function of pH and by isothermal urea denaturation studies as a function of temperature. The P48S and P48A mutants were found to be marginally more stable than the wild-type protein. In the pH range of 5-9, there is an average increase in T(m) values of P48A and P48S of 0.4 degrees C and 0.2 degrees C, respectively, relative to the wild-type protein. The other mutants are less stable than the wild type. Analysis of the effects of such Pro substitutions in MBP and in three other proteins studied to date suggests that substitutions are more likely to be stabilizing if the carbonyl group i-3 or i-4 to the mutation site is not hydrogen bonded in the wild-type protein. Copyright 2003 Wiley-Liss, Inc.

Use of ultrasound in petroleum residue upgradation

Energy Technology Data Exchange (ETDEWEB)

Sawarkar, A.N.; Pandit, A.B.; Samant, S.D.; Joshi, J.B. [Mumbai Univ., Mumbai (India). Inst. of Chemical Technology

2009-06-15

The importance of bottom-of-the barrel upgrading has increased in the current petroleum refining scenario because of the progressively heavier nature of crude oil. Heavy residues contain large concentrations of metals such as vanadium and nickel which foul catalysts and reduce the potential effect of residue fluidized catalytic cracking. This study showed that the cavitational energy induced by ultrasound be be successfully used to upgrade hydrocarbon mixtures. Conventional processes for the upgrading of residual feedstocks, such as thermal cracking and catalytic cracking, were carried out in the temperature range of 400-520 degrees C. Experiments were performed on 2 vacuum residues, Arabian mix vacuum residue (AMVR) and Bombay high vacuum residue (BHVR) and 1 Haldia asphalt (HA). These were subjected to acoustic cavitation for different reaction times from 15 to 120 minutes at ambient temperature and pressure. Two acoustic cavitation devices were compared, namely the ultrasonic bath and ultrasonic horn. In particular, this study compared the ability of these 2 devices to upgrade the petroleum residues to lighter, more value-added products. Different surfactants were used to examine the effect of ultrasound on upgrading the residue when emulsified in water. In order to better understand the reaction mechanism, a kinetic model was developed based on the constituents of the residue. The ultrasonic horn was found to be more effective in bringing about the upgrading than ultrasonic bath. The study also showed that the acoustic cavitation of the aqueous emulsified hydrocarbon mixture could reduce the asphaltenes content to a greater extent than the acoustic cavitation of non-emulsified hydrocarbon mixture. 20 refs., 11 tabs., 17 figs.

Effect of mungbean residue and nitrogen levels on barley

International Nuclear Information System (INIS)

Jan, A.; Muhammad, Z.; Daur, I.; Khan, I.A.

2011-01-01

A field experiment was conducted to evaluate response of barley to mungbean residue (0, 10, 20 and 30 Mg ha/sup -1/), nitrogen levels (0, 25, 50 and 75 kg ha/sup -1/) and their interaction. Emergence m/sup -2/ (50), plant height (109 cm), leaf area tiller-1 (106 cm/sup 2/), lodging score (5.55), termites attack (3.4%), grains spike-1 (67), biological yield (12.80 Mg ha/sup -1/) and grain yield (2.32 Mg ha/sup -1/) were significantly (p=0.05) higher for 30 Mg ha/sup -1/ mungbean residue compared to other levels. Similarly plant height (110 cm), lodging score (5.29) and biological yield (13.75 Mg ha/sup -1/) were higher at 75 kg ha/sup -1/ N compared to other levels of N. Productive tillers m/sup -2/, grains spike/sup -1/, 1000 grain weight, grain yield and harvest index were optimum at 50 kg ha-1 N as compared to 75 kg ha/sup -1/ N that encouraged lodging. Interaction between residue and nitrogen indicated that 10 Mg residue and 50 kg N ha/sup -1/ is recommended to achieve maximum net return under comparable conditions. (author)

Long-term stabilization of crop residues and soil organic carbon affected by residue quality and initial soil pH.

Science.gov (United States)

Wang, Xiaojuan; Butterly, Clayton R; Baldock, Jeff A; Tang, Caixian

2017-06-01

Residues differing in quality and carbon (C) chemistry are presumed to contribute differently to soil pH change and long-term soil organic carbon (SOC) pools. This study examined the liming effect of different crop residues (canola, chickpea and wheat) down the soil profile (0-30cm) in two sandy soils differing in initial pH as well as the long-term stability of SOC at the amended layer (0-10cm) using mid-infrared (MIR) and solid-state 13 C nuclear magnetic resonance (NMR) spectroscopy. A field column experiment was conducted for 48months. Chickpea- and canola-residue amendments increased soil pH at 0-10cm in the Podzol by up to 0.47 and 0.36units, and in the Cambisol by 0.31 and 0.18units, respectively, at 48months when compared with the non-residue-amended control. The decomposition of crop residues was greatly retarded in the Podzol with lower initial soil pH during the first 9months. The MIR-predicted particulate organic C (POC) acted as the major C sink for residue-derived C in the Podzol. In contrast, depletion of POC and recovery of residue C in MIR-predicted humic organic C (HOC) were detected in the Cambisol within 3months. Residue types showed little impact on total SOC and its chemical composition in the Cambisol at 48months, in contrast to the Podzol. The final HOC and resistant organic C (ROC) pools in the Podzol amended with canola and chickpea residues were about 25% lower than the control. This apparent priming effect might be related to the greater liming effect of these two residues in the Podzol. Copyright © 2017 Elsevier B.V. All rights reserved.

Effects of pulse-to-pulse residual species on discharges in repetitively pulsed discharges through packed bed reactors

Science.gov (United States)

Kruszelnicki, Juliusz; Engeling, Kenneth W.; Foster, John E.; Kushner, Mark J.

2016-09-01

Atmospheric pressure dielectric barrier discharges (DBDs) sustained in packed bed reactors (PBRs) are being investigated for conversion of toxic and waste gases, and CO2 removal. These discharges are repetitively pulsed having varying flow rates and internal geometries, which results in species from the prior pulse still being in the discharge zone at the time the following discharge pulse occurs. A non-negligible residual plasma density remains, which effectively acts as preionization. This residual charge changes the discharge properties of subsequent pulses, and may impact important PBR properties such as chemical selectivity. Similarly, the residual neutral reactive species produced during earlier pulses will impact the reaction rates on subsequent pulses. We report on results of a computational investigation of a 2D PBR using the plasma hydrodynamics simulator nonPDPSIM. Results will be discussed for air flowing though an array of dielectric rods at atmospheric pressure. The effects of inter-pulse residual species on PBR discharges will be quantified. Means of controlling the presence of residual species in the reactor through gas flow rate, pulse repetition, pulse width and geometry will be described. Comparisons will be made to experiments. Work supported by US DOE Office of Fusion Energy Science and the National Science Foundation.

Effects of material non-linearity on the residual stresses in a dendritic silicon crystal ribbon

Science.gov (United States)

Ray, Sujit K.; Utku, Senol

1990-01-01

Thermal stresses developed in a dendritic silicon crystal ribbon have been shown to cause plastic deformation and residual stresses in the ribbon. This paper presents an implementation of a numerical model proposed for thermoelastoplastic behavior of a material. The model has been used to study the effects of plasticity of silicon on the residual stresses. The material properties required to implement this model are all assumed, and the response of the material to the variations in these assumed parameters of the constitutive law and in the finite element mesh is investigated. The steady state growth process is observed to be periodic with nonzero residual stresses. Numerical difficulties are also encountered in the computer solution process, resulting in sharp jumps and large oscillations in the stress responses.

Fatigue life estimation of welded components considering welding residual stress relaxation and its mean stress effect

International Nuclear Information System (INIS)

Han, Seung Ho; Han, Jeong Woo; Shin, Byung Chun; Kim, Jae Hoon

2003-01-01

The fatigue life of welded joints is sensitive to welding residual stress and complexity of their geometric shapes. To predict the fatigue life more reasonably, the effects of welding residual stress and its relaxation on their fatigue strengths should be considered quantitatively, which are often regarded to be equivalent to the effects of mean stresses by external loads. The hot-spot stress concept should be also adopted which can reduce the dependence of fatigue strengths for various welding details. Considering the factors mentioned above, a fatigue life prediction model using the modified Goodman's diagram was proposed. In this model, an equivalent stress was introduced which is composed of the mean stress based on the hot-spot stress concept and the relaxed welding residual stress. From the verification of the proposed model to real welding details, it is proved that this model can be applied to predict reasonably their fatigue lives

Effectiveness of a constructed wetland for treating alkaline bauxite residue leachate: a 1-year field study.

Science.gov (United States)

Higgins, Derek; Curtin, Teresa; Courtney, Ronan

2017-03-01

Increasing volumes of bauxite residues and their associated leachates represent a significant environmental challenge to the alumina industry. Constructed wetlands have been proposed as a potential approach for leachate treatment, but there is limited data on field-scale applications. The research presented here provides preliminary evaluation of a purpose-built constructed wetland to buffer leachate from a bauxite residue disposal site in Ireland. Data collected over a 1-year period demonstrated that the pH of bauxite residue leachates could be effectively reduced from ca. pH 10.3 to 8.1 but was influenced by influent variability and temporal changes. The wetland was also effective in decreasing elemental loading, and sequential extractions suggested that the bulk of the sediment-bound metal inventory was in hard-to-leach phases. Elemental analysis of Phragmites australis showed that although vegetation displayed seasonal variation, no trace elements were at concentrations of concern.

Effect of microwave postpolymerization treatment on residual monomer content and the flexural strength of autopolymerizing reline resin

Directory of Open Access Journals (Sweden)

Patil Padmakar

2009-01-01

Full Text Available Background : Microwave postpolymerization has been suggested as a method to improve the flexural strength of an autopolymerizing denture reline resin. However, the effect of microwave postpolymerization on the residual monomer content and its influence on flexural strength have not been investigated. Objectives : This study analyzed the effect of microwave postpolymerization on the residual monomer content and its influence on the flexural strength of an autopolymerizing reline resin (Denture Liner. Materials and Methods : A total of 70 specimens (64 Χ 10 Χ 3.3 mm were polymerized according to the manufacturer′s instructions and divided into 7 groups (n = 10. Control group specimens were not subjectedto any further processing. Before testing, the specimens were subjected to postpolymerization in a microwave oven using different power (550 and 650 W and time (3, 4, and 5 min settings. Two specimens of each group were then manually ground into fine powder and samples extracted from the specimens using reflux method. The samples were then subjected to gas chromatography for residual monomer determination in area%. Eight specimens were subjected to a three-point bending device with a span of 50 mm and crosshead speed of 5 mm/min, and the flexural strength was determined in MPa. Data analyses included Student′s t-test and one-way analysis of variance. Results : For the Denture Liner reline resin, the residual monomer content decreased and the flexural strength increased significantly with the application of microwave irradiation using different time/power combinations. The specimens with the lowest residual monomer content were the similar specimens which presented with the highest flexural strength. Conclusion : Microwave postpolymerization irradiation can be an effective method for increasing the flexural strength of denture liner (at 650 W for 5 min by reducing the residual monomer content by further polymerization at free radical sites.

Estimation of average causal effect using the restricted mean residual lifetime as effect measure

DEFF Research Database (Denmark)

Mansourvar, Zahra; Martinussen, Torben

2017-01-01

with respect to their survival times. In observational studies where the factor of interest is not randomized, covariate adjustment is needed to take into account imbalances in confounding factors. In this article, we develop an estimator for the average causal treatment difference using the restricted mean...... residual lifetime as target parameter. We account for confounding factors using the Aalen additive hazards model. Large sample property of the proposed estimator is established and simulation studies are conducted in order to assess small sample performance of the resulting estimator. The method is also......Although mean residual lifetime is often of interest in biomedical studies, restricted mean residual lifetime must be considered in order to accommodate censoring. Differences in the restricted mean residual lifetime can be used as an appropriate quantity for comparing different treatment groups...

Effect of different soil washing solutions on bioavailability of residual arsenic in soils and soil properties.

Science.gov (United States)

Im, Jinwoo; Yang, Kyung; Jho, Eun Hea; Nam, Kyoungphile

2015-11-01

The effect of soil washing used for arsenic (As)-contaminated soil remediation on soil properties and bioavailability of residual As in soil is receiving increasing attention due to increasing interest in conserving soil qualities after remediation. This study investigates the effect of different washing solutions on bioavailability of residual As in soils and soil properties after soil washing. Regardless of washing solutions, the sequential extraction revealed that the residual As concentrations and the amount of readily labile As in soils were reduced after soil washing. However, the bioassay tests showed that the washed soils exhibited ecotoxicological effects - lower seed germination, shoot growth, and enzyme activities - and this could largely be attributed to the acidic pH and/or excessive nutrient contents of the washed soils depending on washing solutions. Overall, this study showed that treated soils having lower levels of contaminants could still exhibit toxic effects due to changes in soil properties, which highly depended on washing solutions. This study also emphasizes that data on the As concentrations, the soil properties, and the ecotoxicological effects are necessary to properly manage the washed soils for reuses. The results of this study can, thus, be utilized to select proper post-treatment techniques for the washed soils. Copyright © 2015 Elsevier Ltd. All rights reserved.

Effect of rolling on the residual stresses and magnetic properties of a 0.5% Si electrical steel

International Nuclear Information System (INIS)

Campos, M.F. de; Sablik, M.J.; Landgraf, F.J.G.; Hirsch, T.K.; Machado, R.; Magnabosco, R.; Gutierrez, C.J.; Bandyopadhyay, A.

2008-01-01

Cold-rolled (0-19% of reduction) 0.5% Si electrical steel sheets were studied in detail, including macro and micro residual stress measurements, crystallographic texture, dc-hysteresis curves and iron losses. Even for the smallest deformation, losses increase significantly, with large increase of the hysteresis losses, whereas the anomalous losses reduce slightly. The residual microstresses are ∼150-350 MPa, whereas residual macrostresses are compressive, ∼50 MPa. The large increase of the hysteresis losses is attributed to the residual microstresses. The dislocation density estimated by X-ray diffraction is in reasonable agreement with that predicted from the Sablik et al. model for effect of plastic deformation on hysteresis. The intensity of the texture fibers {1 1 1} and //RD (RD=rolling direction) increases with the reduction

Effect of preemptive weld overlay on residual stress mitigation for dissimilar metal weld of nuclear power plant pressurizer

International Nuclear Information System (INIS)

Song, Tae Kwang; Bae, Hong Yeol; Chun, Yun Bae; Oh, Chang Young; Kim, Yun Jae; Lee, Kyoung Soo; Park, Chi Yong

2008-01-01

Weld overlay is one of the residual stress mitigation methods which arrest crack initiation and crack growth. Therefore weld overlay can be applied to the region where cracking is likely to be. An overlay weld used in this manner is termed a Preemptive Weld OverLay(PWOL). In Pressurized Water Reactor(PWR) dissimilar metal weld is susceptible region for Primary Water Stress Corrosion Cracking(PWSCC). In order to examine the effect of PWOL on residual stress mitigation, PWOL was applied to a specific dissimilar metal weld of Kori nuclear power plant by finite element analysis method. As a result, strong compressive residual stress was made in PWSCC susceptible region and PWOL was proved effective preemptive repair method for weldment

Effect of preemptive weld overlay on residual stress mitigation for dissimilar metal weld of nuclear power plant pressurizer

Energy Technology Data Exchange (ETDEWEB)

Song, Tae Kwang; Bae, Hong Yeol; Chun, Yun Bae; Oh, Chang Young; Kim, Yun Jae [Korea University, Seoul (Korea, Republic of); Lee, Kyoung Soo; Park, Chi Yong [Korea Electric Power Research Institute, Daejeon (Korea, Republic of)

2008-10-15

Weld overlay is one of the residual stress mitigation methods which arrest crack initiation and crack growth. Therefore weld overlay can be applied to the region where cracking is likely to be. An overlay weld used in this manner is termed a Preemptive Weld OverLay(PWOL). In Pressurized Water Reactor(PWR) dissimilar metal weld is susceptible region for Primary Water Stress Corrosion Cracking(PWSCC). In order to examine the effect of PWOL on residual stress mitigation, PWOL was applied to a specific dissimilar metal weld of Kori nuclear power plant by finite element analysis method. As a result, strong compressive residual stress was made in PWSCC susceptible region and PWOL was proved effective preemptive repair method for weldment.

Petroleum residue upgrading with dispersed catalysts: Part 2. Effect of operating conditions

Energy Technology Data Exchange (ETDEWEB)

Panariti, N.; Del Bianco, A.; Del Piero, G. [ENITECNOLOGIE S.p.A, Via Maritano 26, 20097 San Donato Mil (Italy); Marchionna, M. [SNAMPROGETTI S.p.A, Via Maritano 26, 20097 San Donato Mil (Italy); Carniti, P. [Universita degli Studi di Milano, Dip. Chimica Fisica ed Elettrochimica, Via Celoria 20, Milan (Italy)

2000-12-04

The hydrotreatment of a petroleum residue in the presence of dispersed molybdenite was carried out within a wide range of operating conditions and catalyst loading. The effect of reaction severity as well as of molybdenum concentration on product distribution and quality was studied. Based on the experimental results, a simplified reaction scheme was proposed. The hydroprocessing of the residue was described in terms of the competition between two reactions: the direct conversion of the feedstock to distillate and coke, and the catalytic hydrogenation. Compared to thermal conditions, the presence of dispersed molybdenite controls very well coke formation; however, a trend of increasing formation of solids was observed at high catalyst concentrations. The overall upgrading of the feedstock requires significant amounts of molybdenum as well as relatively high hydrogen pressure.

Standard test method for determining the effective elastic parameter for X-ray diffraction measurements of residual stress

CERN Document Server

American Society for Testing and Materials. Philadelphia

1998-01-01

1.1 This test method covers a procedure for experimentally determining the effective elastic parameter, Eeff, for the evaluation of residual and applied stresses by X-ray diffraction techniques. The effective elastic parameter relates macroscopic stress to the strain measured in a particular crystallographic direction in polycrystalline samples. Eeff should not be confused with E, the modulus of elasticity. Rather, it is nominally equivalent to E/(1 + ν) for the particular crystallographic direction, where ν is Poisson's ratio. The effective elastic parameter is influenced by elastic anisotropy and preferred orientation of the sample material. 1.2 This test method is applicable to all X-ray diffraction instruments intended for measurements of macroscopic residual stress that use measurements of the positions of the diffraction peaks in the high back-reflection region to determine changes in lattice spacing. 1.3 This test method is applicable to all X-ray diffraction techniques for residual stress measurem...

Nonlinear Model of Pseudoelastic Shape Memory Alloy Damper Considering Residual Martensite Strain Effect

Directory of Open Access Journals (Sweden)

Y. M. Parulekar

2012-01-01

Full Text Available Recently, there has been increasing interest in using superelastic shape memory alloys for applications in seismic resistant-design. Shape memory alloys (SMAs have a unique property by which they can recover their original shape after experiencing large strains up to 8% either by heating (shape memory effect or removing stress (pseudoelastic effect. Many simplified shape memory alloy models are suggested in the past literature for capturing the pseudoelastic response of SMAs in passive vibration control of structures. Most of these models do not consider the cyclic effects of SMA's and resulting residual martensite deformation. Therefore, a suitable constitutive model of shape memory alloy damper which represents the nonlinear hysterical dynamic system appropriately is essential. In this paper a multilinear hysteretic model incorporating residual martensite strain effect of pseudoelastic shape memory alloy damper is developed and experimentally validated using SMA wire, based damper device. A sensitivity analysis is done using the proposed model along with three other simplified SMA models. The models are implemented on a steel frame representing an SDOF system and the comparison of seismic response of structure with all the models is made in the numerical study.

XPS and STEM studies of Allende acid insoluble residues

Science.gov (United States)

Housley, R. M.; Clarke, D. R.

1980-01-01

Data on Allende acid residues obtained both before and after etching with hot HNO3 are presented. X-ray photoelectron spectra show predominantly carbonaceous material plus Fe-deficient chromite in both cases. The HNO3 oxidizes the carbonaceous material to some extent. The small chromites in these residues have a wide range of compositions somewhat paralleling those observed in larger Allende chromites and in Murchison chromites, especially in the high Al contents; however, they are deficient in divalent cations, which makes them metastable and indicates that they must have formed at relatively low temperatures. It is suggested that they formed by precipitation of Cr(3+) and Fe(3+) from olivine at low temperature or during rapid cooling.

Nitrogen availability of biogas residues

Energy Technology Data Exchange (ETDEWEB)

El-Sayed Fouda, Sara

2011-09-07

The objectives of this study were to characterize biogas residues either unseparated or separated into a liquid and a solid phase from the fermentation of different substrates with respect to their N and C content. In addition, short and long term effects of the application of these biogas residues on the N availability and N utilization by ryegrass was investigated. It is concluded that unseparated or liquid separated biogas residues provide N at least corresponding to their ammonium content and that after the first fertilizer application the C{sub org}:N{sub org} ratio of the biogas residues was a crucial factor for the N availability. After long term application, the organic N accumulated in the soil leads to an increased release of N.

The Effect of Crop Residue and Different NPK Fertilizer Rates on yield Components and Yield of Wheat

Directory of Open Access Journals (Sweden)

fatemeh khamadi

2017-08-01

Full Text Available Introduction Integrated nutrient management involving crop residue/green manures and chemical fertilizer is potential alternative to provide a balanced supply of nutrients, enhance soil quality and thereby sustain higher productivity. The present experiment was undertaken to evaluate the effect of different crop residue management practices and NPK levels on yield components and yield of wheat. Materials and methods Field experiments were conducted during 2012-2014 at department of agronomy, Chamran University. Experiment was laid out in a randomized block designs in split plot arrangement. With three replications. Crop residues were assigned to main plot consistent CR1: wheat residue; CR2: rape residue; CR3: barley residue; CR4: barley residue + vetch; CR5: wheat straw + mungbean; CR6: vetch residue; CR7: mungbean residue; CR8: No residue incorporation as main plot and three NPK fertilizer rates: F1: (180N-120P-100K kg.ha-1; F2: (140N-90P-80K kg.ha-1; F3: (90N-60P-40K kg.ha-1 as sub plots. Twelve hills were collected at physiological maturity for measuring yield components from surrounding area of grain yield harvest area. Yield components, viz. number of spike per m2, seed per spike, 1000- grain weight, plant height were measured. Grain and straw yields were recorded from the central 5 m2 grain yield harvest area of each treatment and harvest index was calculated. Data were subjected to analysis by SAS and mean companions were performed using the Duncan multiple range test producer. Also, graphs were drawn in Excel software. Results and discussion The result of analysis variance showed significant difference between crop residues for evaluated traits. The result indicated that the highest biological and grain yield was obtained when wheat treated with CR5: wheat straw + mungbean (green manure and CR4: barley straw + vetch (green manure. Biological and grain yield increased 31 and 26% respectively by CR5 comparing with control. The highest

The effect of actinides on the microstructural development in a metallic high-level nuclear waste form

Energy Technology Data Exchange (ETDEWEB)

Keiser, D. D., Jr.; Sinkler, W.; Abraham, D. P.; Richardson, J. W., Jr.; McDeavitt, S. M.

1999-10-25

Waste forms to contain material residual from an electrometallurgical treatment of spent nuclear fuel have been developed by Argonne National Laboratory. One of these waste forms contains waste stainless steel (SS), fission products that are noble to the process (e.g., Tc, Ru, Pd, Rh), Zr, and actinides. The baseline composition of this metallic waste form is SS-15wt.% Zr. The metallurgy of this baseline alloy has been well characterized. On the other hand, the effects of actinides on the alloy microstructure are not well understood. As a result, SS-Zr alloys with added U, Pu, and/or Np have been cast and then characterized, using scanning electron microscopy, transmission electron microscopy, and neutron diffraction, to investigate the microstructural development in SS-Zr alloys that contain actinides. Actinides were found to congregate non-uniformally in a Zr(Fe,Cr,Ni){sub 2+x} phase. Apparently, the actinides were contained in varying amounts in the different polytypes (C14, C15, and C36) of the Zr(Fe,Cr,Ni){sub 2+x} phase. Heat treatment of an actinide-containing SS-15 wt.% Zr alloy showed the observed microstructure to be stable.

Effect of cryogenic treatment on distribution of residual stress in case carburized En 353 steel

International Nuclear Information System (INIS)

Bensely, A.; Venkatesh, S.; Mohan Lal, D.; Nagarajan, G.; Rajadurai, A.; Junik, Krzysztof

2008-01-01

The effect of cryogenic treatment on the distribution of residual stress in the case carburized steel (En 353) was studied using X-ray diffraction technique. Two types of cryogenic treatment: shallow cryogenic treatment (193 K) and deep cryogenic treatment (77 K) were adopted, as a supplement to conventional heat treatment. The amount of retained austenite in conventionally heat-treated, shallow cryogenically treated and deep cryogenically treated samples was found to be 28%, 22% and 14%, respectively. The conventionally heat-treated, shallow cryogenically treated and deep cryogenically treated samples in untempered condition had a surface residual stress of -125 MPa, -115 MPa and -235 MPa, respectively. After tempering the conventionally heat-treated, shallow cryogenically treated and deep cryogenically treated samples had a surface residual stress of -150 MPa, -80 MPa and -80 MPa, respectively. A comparative study of the three treatments revealed that there was an increase in the compressive residual stress in steel that was subjected to cryogenic treatment prior to tempering. The experimental investigation revealed that deep cryogenically treated steel when subjected to tempering has undergone a reduction in compressive residual stress. Such stress relieving behaviour was mainly due to the increased precipitation of fine carbides in specimens subjected to DCT with tempering

Effects on residual stresses of aluminum alloy LC4 by laser shock processing

Science.gov (United States)

Zhang, Yong-kang; Lu, Jin-zhong; Kong, De-jun; Yao, Hui-xue; Yang, Chao-jun

2007-12-01

The influences of processing parameters on laser-induced shock waves in metal components are discussed and analyzed. The effects of different parameters of laser shock processing (LSP) on residual stress of aerospace aluminum alloy LC4 were investigated. LSP was performed by using an Nd: glass phosphate laser with 23 ns pulse width and up to ~45 J pulse energy at power densities above GW/mm -2. Special attention is paid to the residual stresses from laser shock processing. Modification of microstructure, surface morphology by laser shock processing is also discussed. Results to date indicate that laser shock processing has great potential as a means of improving the mechanical performance of components.

Effect of Solder Flux Residues on Corrosion of Electronics

DEFF Research Database (Denmark)

Hansen, Kirsten Stentoft; Jellesen, Morten Stendahl; Møller, Per

2009-01-01

Flux from ‘No Clean’ solder processes can cause reliability problems in the field due to aggressive residues, which may be electrical conducting or corrosive in humid environments. The solder temperature during a wave solder process is of great importance to the amount of residues left on a PCBA...... testing and use in the field, consequences and recommendations are given. Failures, caused by harsh[1] customer environments, are not covered in this paper....

Residual N effect of long-term applications of cattle slurry using winter wheat as test crop

DEFF Research Database (Denmark)

Suarez, Alfonso; Thomsen, Ingrid Kaag; Rasmussen, Jim

2018-01-01

) as reference treatments. In the test years, the customary nutrient treatments were withheld and each plot divided into six subplots randomly allocated increasing rates of mineral fertilizer N (0–250 kg N ha−1). The winter wheat yielded more in the first test year due to crop rotational effects and more benign...... climatic conditions, substantiating that more test years are needed when estimating residual N effects. The residual value of N added previously with NPK was negligible. In the first year, grain yields at N optimum were similar for NPK and SLU, but the amount of fertilizer N needed to reach optimum yield...... in cattle slurry (50, 100 and 150 kg total-N ha−1 termed ½, 1 and 1½ SLU), we estimated the residual N value over two consecutive growth periods (2014/2015 and 2015/2016). We used winter wheat as test crop and soils with a history of mineral fertilizers only (1 PK (no N)) and 1 NPK (100 kg N ha−1...

Allelopathic Effect of Wheat and Barley Residues on Yield and Yield Components of Cowpea (Vigna sinensis L. and Weeds Control

Directory of Open Access Journals (Sweden)

M Shahbyki

2018-02-01

residue at a rate of 4 and 8 ton ha-1 significantly decreased weed density than non-weeding treatment. Seed number per pod, biological and grain yield of cowpea significantly increased in the soil incorporation with wheat residue at a rate of 8 ton ha-1 compared to control. Our results showed that weeding and soil incorporation with wheat residue at a rate of 8 ton ha-1 increased cowpea yield by 78.23 and 80.79% compared to no weeding treatment, respectively. Wheat is a potent source of bioactive phytotoxic compounds representing three main classes as phenolic (hydroxybenzoic, vanillic, pcoumaric, syringic and ferulic acids being most frequently reported and transferulic and trans-pcoumaric acids being the dominant acids, cyclic hydroxamic acids (a class of alkaloids and short chain fatty acids. It is reported that wheat extract compounds can interfere with basic processes of receiver plants as photosynthesis, cell division, respiration and protein synthesis and indirectly provoke other forms of stresses. Thus, these compounds can reduce weed germination and growth. Another important effect of these allelochemicals is the activation of cellular antioxidant system in response to uncontrolled production and accumulation of reactive oxygen species. The reason for increase in grain yield was the control of weeds and probably the allelopathic effects of crop water extracts promoted the wheat growth which ultimately increases grain yield. Conclusions The present study concluded that wheat phytotoxins in straw inhibited germination and seedling growth of weeds, and the inhibition was concentration-dependent. Also wheat straw added to soil increased yield and some traits of cowpea. In general, the results showed that wheat straw can reduce weed suppression and can improve characteristics of plant, moreover, decreased environment risks of chemical inputs and ensure sustainability of production in long time.

Effect of bentonite addition on residual strength of microwave-hardened waterglass-containing moulding sands

Directory of Open Access Journals (Sweden)

M. Stachowicz

2011-07-01

Full Text Available The paper presents results of a preliminary research of the effect of bentonite addition on residual strength of microwave-hardened moulding sands, containing sodium waterglass. Strength was determined at ambient temperature, on cylindrical specimens baked in an oven. Moulding sands for examinations were based on high-silica sand with addition of 2.5 % of non-modified, domestic-made waterglass grade 145. The prepared standard cylindrical specimens were hardened using the innovative microwave heating process and next baked for 30 minutes at temperatures between 100 and 1200 °C. Strength parameters of the specimens were determined on the specimens cooled- down to ambient temperature. The obtained results were compared with literature data to evaluate the effect of the applied hardening method and of the special additive on residual strength as a function of baking temperature. A favourable effect was found of both the innovative heating process and the applied bentonite addition.

Mixed-waste treatment -- What about the residuals?

International Nuclear Information System (INIS)

Carlson, T.; Carpenter, C.; Cummins, L.; Haas, P.; MacInnis, J.; Maxwell, C.

1993-01-01

Incineration currently is the best demonstrated available technology for the large inventory of U.S. Department of Energy (DOE) mixed waste. However, molten salt oxidation (MSO) is an alternative thermal treatment technology with the potential to treat a number of these wastes. Of concern for both technologies is the final waste forms, or residuals, that are generated by the treatment process. An evaluation of the two technologies focuses on 10 existing DOE waste streams and current hazardous-waste regulations, specifically for the delisting of ''derived-from'' residuals. Major findings include that final disposal options are more significantly impacted by the type of waste treated and existing regulations than by the type of treatment technology; typical DOE waste streams are not good candidates for delisting; and mass balance calculations indicate that MSO and incineration generate similar quantities (dry) and types of residuals

Unstable argininosuccinate lyase in variant forms of the urea cycle disorder argininosuccinic aciduria.

Science.gov (United States)

Hu, Liyan; Pandey, Amit V; Balmer, Cécile; Eggimann, Sandra; Rüfenacht, Véronique; Nuoffer, Jean-Marc; Häberle, Johannes

2015-09-01

Loss of function of the urea cycle enzyme argininosuccinate lyase (ASL) is caused by mutations in the ASL gene leading to ASL deficiency (ASLD). ASLD has a broad clinical spectrum ranging from life-threatening severe neonatal to asymptomatic forms. Different levels of residual ASL activity probably contribute to the phenotypic variability but reliable expression systems allowing clinically useful conclusions are not yet available. In order to define the molecular characteristics underlying the phenotypic variability, we investigated all ASL mutations that were hitherto identified in patients with late onset or mild clinical and biochemical courses by ASL expression in human embryonic kidney 293 T cells. We found residual activities >3% of ASL wild type (WT) in nine of 11 ASL mutations. Six ASL mutations (p.Arg95Cys, p.Ile100Thr, p.Val178Met, p.Glu189Gly, p.Val335Leu, and p.Arg379Cys) with residual activities ≥16% of ASL WT showed no significant or less than twofold reduced Km values, but displayed thermal instability. Computational structural analysis supported the biochemical findings by revealing multiple effects including protein instability, disruption of ionic interactions and hydrogen bonds between residues in the monomeric form of the protein, and disruption of contacts between adjacent monomeric units in the ASL tetramer. These findings suggest that the clinical and biochemical course in variant forms of ASLD is associated with relevant residual levels of ASL activity as well as instability of mutant ASL proteins. Since about 30% of known ASLD genotypes are affected by mutations studied here, ASLD should be considered as a candidate for chaperone treatment to improve mutant protein stability.

Residual Entropy, the Third Law and Latent Heat

Directory of Open Access Journals (Sweden)

Frank L. Lambert

2008-09-01

Full Text Available A novel thermodynamic treatment of residual entropy in crystals, involving the configurational partition function, is suggested, which is consistent with both classical and statistical thermodynamics. It relates residual entropy to the inherent latent heat which would be released upon cooling if the reversible path were available. The nature of this heat is that if the crystal possessing residual entropy freezes above its Boltzmann’s characteristic temperature of molecular alignment, the difference in energy between different molecular arrangements is overcome by the kT heat bath to form a nearly-ideal solution. However, upon cooling below this characteristic temperature, they would separate with a concomitant release of the corresponding energy, provided the reversible path were available.

Characterization of active site residues of nitroalkane oxidase.

Science.gov (United States)

Valley, Michael P; Fenny, Nana S; Ali, Shah R; Fitzpatrick, Paul F

2010-06-01

The flavoenzyme nitroalkane oxidase catalyzes the oxidation of primary and secondary nitroalkanes to the corresponding aldehydes and ketones plus nitrite. The structure of the enzyme shows that Ser171 forms a hydrogen bond to the flavin N5, suggesting that it plays a role in catalysis. Cys397 and Tyr398 were previously identified by chemical modification as potential active site residues. To more directly probe the roles of these residues, the S171A, S171V, S171T, C397S, and Y398F enzymes have been characterized with nitroethane as substrate. The C397S and Y398 enzymes were less stable than the wild-type enzyme, and the C397S enzyme routinely contained a substoichiometric amount of FAD. Analysis of the steady-state kinetic parameters for the mutant enzymes, including deuterium isotope effects, establishes that all of the mutations result in decreases in the rate constants for removal of the substrate proton by approximately 5-fold and decreases in the rate constant for product release of approximately 2-fold. Only the S171V and S171T mutations alter the rate constant for flavin oxidation. These results establish that these residues are not involved in catalysis, but rather are required for maintaining the protein structure. 2009 Elsevier Inc. All rights reserved.

A two-stage bioprocess for hydrogen and methane production from rice straw bioethanol residues.

Science.gov (United States)

Cheng, Hai-Hsuan; Whang, Liang-Ming; Wu, Chao-Wei; Chung, Man-Chien

2012-06-01

This study evaluates a two-stage bioprocess for recovering hydrogen and methane while treating organic residues of fermentative bioethanol from rice straw. The obtained results indicate that controlling a proper volumetric loading rate, substrate-to-biomass ratio, or F/M ratio is important to maximizing biohydrogen production from rice straw bioethanol residues. Clostridium tyrobutyricum, the identified major hydrogen-producing bacteria enriched in the hydrogen bioreactor, is likely utilizing lactate and acetate for biohydrogen production. The occurrence of acetogenesis during biohydrogen fermentation may reduce the B/A ratio and lead to a lower hydrogen production. Organic residues remained in the effluent of hydrogen bioreactor can be effectively converted to methane with a rate of 2.8 mmol CH(4)/gVSS/h at VLR of 4.6 kg COD/m(3)/d. Finally, approximately 75% of COD in rice straw bioethanol residues can be removed and among that 1.3% and 66.1% of COD can be recovered in the forms of hydrogen and methane, respectively. Copyright © 2012 Elsevier Ltd. All rights reserved.

Effect of turning frequency on co-composting pig manure and fungus residue.

Science.gov (United States)

Jiang-Ming, Zhou

2017-03-01

Composting of agricultural wastes not only can reduce environmental pollution caused by improper disposal, but also can recycle agricultural wastes and transform them into highly valuable products, such as fertilizers or soil conditioners, for agricultural applications. However, the composting process and final product are easily affected by the limited oxygen supply that results from insufficient aeration, especially in the center of a large-scale windrow. Hence, a pilot-scale experiment was conducted to investigate the effects of the turning frequency on the composting efficiency and compost quality of used pig manure and fungus residue. Physical and chemical characteristics were measured over the course of 63 days of composting. The data indicate that higher temperatures and more rapid moisture removal generally result from a turning treatment of once every 2-4 days than in fewer, or no, turning treatments. The total nitrogen, total phosphorus, and total potassium contents increased in all windrows as the organic matter content decreased, but both the increases and decrease were greater in windrows that were turned more frequently. The reduction of the organic matter mass by 53.7-66.0% for a turning of once every 2-8 days is significantly higher than that for the static windrow (39.1%). Although there is an increase in nitrogen mass loss with an increased turning frequency, lower nitrogen mass losses (12.7-25.7%) in all treatments were noted compared with previous studies. A final compost product with less moisture, less weight, higher nutrient content (N, P, and K), and greater stability was obtained in windrows with turning frequencies of once every 2-4 days, which is recommended when composting pig manure and fungus residue. Composting of agricultural wastes not only can reduce environmental pollution caused by improper disposal, but recycling of agricultural wastes transforms them into highly valuable products, such as fertilizers or soil conditioners, for

Effect of processing on the disappearance of pesticide residues in fresh-cut lettuce: Bioavailability and dietary risk.

Science.gov (United States)

Camara, Miguel A; Barba, Alberto; Cermeño, Sandra; Martinez, Gracia; Oliva, Jose

2017-12-02

The aim of this research is to establish the processing factors of six pesticides durong the preparation of fresh-cut lettuce and to assess the risk of ingestion of pesticide residues associated with the consumption of the same. A field study was carried out on the dissipation of three insecticides (imidacloprid, tebufenozide, cypermethrin) and three fungicides (metalaxyl, tebuconazole, azoxystrobin) during treatment conditions simulating those used for commercial fresh-cut lettuce. A simultaneous residue analysis method is validated using QuEChERS extraction with acetonitrile and CG-MS and LC-MS/MS analysis. The residues detected after field application never exceed the established Maximum Residue Limits. The processing factors were generally less than 1 (between 0.34 for tebufenozide and 0.53 for imidacloprid), indicating that the process, as a whole, considerably reduces residue levels in processed lettuce compared to fresh lettuce. It is confirmed that cutting, followed by washing and drying, considerably reduces the residues. A matrix effect in the dialyzation of the pesticides is observed and the in vitro study of bioavailability establishes a low percentage of stomach absorption capacity (lettuce showed no concerns for consumer health.

Cover crop residue management for optimizing weed control

NARCIS (Netherlands)

Kruidhof, H.M.; Bastiaans, L.; Kropff, M.J.

2009-01-01

Although residue management seems a key factor in residue-mediated weed suppression, very few studies have systematically compared the influence of different residue management strategies on the establishment of crop and weed species. We evaluated the effect of several methods of pre-treatment and

Effect of irradiation on erythromycin residues in poultry meat

International Nuclear Information System (INIS)

Mazurowski, P.

1993-01-01

Ionising radiation in doses used for radurisation (Recommendations of international organizations admit for poultry meat doses up to 5 kGy. Practically doses up to 3 kGy are applied does not influence erythromycin concentration in poultry meat. Doses on a level 10 kGy reduce its concentration in slurry more effectively, but results of earlier studies on penicillin and streptomycin suggest, that reduction of erythromycin level in meat should be smaller than in slurry. This allows an assumption that poultry meat irradiation with radurisation doses (up to 5 kGy), does not cause danger of overlooking of erythromycin residues in meat, with traditional, microbiological methods of detection. (orig.)

[Effects of mushroom residue compost on growth and nutrient accumulation of Larix principis-rupprechtii containerized transplants].

Science.gov (United States)

Teng, Fei; Liu, Yong; Lou, Jun Shan; Sun, Qiao Yu; Wan, Fang Fang; Yang, Chen; Zhang, Jin

2016-12-01

Excessive use of peat may cause some environmental problems. To alleviate the negative effect, an experiment was conducted with the mushroom residue compost to replace peat in Larix principis-rupprechtii containerized transplant production, and the proportion of mushroom residue compost was 0% (T 0 , control), 15% (T 1 ), 18.75% (T 2 ), 25% (T 3 ), 37.50% (T 4 ), 50% (T 5 ), 56.25% (T 6 ) and 60% (T 7 ), respectively. The physical and chemical features of the substrates and its effect on the vegetative growth and nutrient accumulation of L. principis-rupprechtii containerized transplants were studied. The results showed when the proportion of mushroom residue compost in the substrate accounted for 50% or less, there was no significant difference in the transplant height, diameter, and biomass compared with the control, and the nutrient concentration in T 2 , T 4 , T 5 treatments was significantly higher than in T 0 . The pH value was sub-acidic to neutral which was suitable to the transplant growth. When the compost proportion accounted for more than 50%, the pH value was altered to alkali and was not suitable to the transplant growth. When the proportion of mushroom residue compost accounted for 15%, the plant grew best, and the height, diameter, and total biomass got the highest. Therefore, using mushroom residue compost to replace peat in L. principis-rupprechtii containerized transplants cultivation was feasible and the maximum replacement ratio could reach 50%. The high quality transplants could be obtained when the compost replacement ratio was 15%.

Resource characterization and residuals remediation, Task 1.0: Air quality assessment and control, Task 2.0: Advanced power systems, Task 3.0: Advanced fuel forms and coproducts, Task 4.0

Energy Technology Data Exchange (ETDEWEB)

Hawthorne, S.B.; Timpe, R.C.; Hartman, J.H. [and others

1994-02-01

This report addresses three subtasks related to the Resource Characterization and Residuals Remediation program: (1) sulfur forms in coal and their thermal transformations, (2) data resource evaluation and integration using GIS (Geographic Information Systems), and (3) supplementary research related to the Rocky Mountain 1 (RM1) UCG (Underground Coal Gasification) test program.

Fertilizer nitrogen recovery efficiencies in crop production systems of China with and without consideration of the residual effect of nitrogen

International Nuclear Information System (INIS)

Yan, Xiaoyuan; Ti, Chaopu; Zhu, Zhaoliang; Vitousek, Peter; Chen, Deli; Leip, Adrian; Cai, Zucong

2014-01-01

China is the world’s largest consumer of synthetic nitrogen (N), where very low rates of fertilizer N recovery in crops have been reported, raising discussion around whether fertilizer N use can be significantly reduced without yield penalties. However, using recovery rates as indicator ignores a possible residual effect of fertilizer N—a factor often unknown at large scales. Such residual effect might store N in the soil increasing N availability for subsequent crops. The objectives of the present study were therefore to quantify the residual effect of fertilizer N in China and to obtain more realistic rates of the accumulative fertilizer N recovery efficiency (RE) in crop production systems of China. Long-term spatially-extensive data on crop production, fertilizer N and other N inputs to croplands in China were used to analyze the relationship between crop N uptake and fertilizer N input (or total N input), and to estimate the amount of residual fertilizer N. Measurement results of cropland soil N content in two time periods were obtained to compare the change in the soil N pool. At the provincial scale, it was found that there is a linear relationship between crop N uptake and fertilizer N input or total N input. With the increase in fertilizer N input, annual direct fertilizer N RE decreased and was indeed low (below 30% in recent years), while its residual effect increased continuously, to the point that 40–68% of applied fertilizer was used for crop production sooner or later. The residual effect was evidenced by a buildup of soil N and a large difference between nitrogen use efficiencies of long-term and short-term experiments. (paper)

Wet oxidative degradation of cellulosic wastes 5- chemical and thermal properties of the final waste forms

International Nuclear Information System (INIS)

Eskander, S.B.; Saleh, H.M.

2002-01-01

In this study, the residual solution arising from the wet oxidative degradation of solid organic cellulosic materials, as one of the component of radioactive solid wastes, using hydrogen peroxide as oxidant. Were incorporated into ordinary Portland cement matrix. Leaching as well as thermal characterizations of the final solidified waste forms were evaluated to meet the final disposal requirements. Factors, such as the amount of the residual solution incorporated, types of leachant. Release of different radionuclides and freezing-thaw treatment, that may affect the leaching characterization. Were studied systematically from the data obtained, it was found that the final solid waste from containing 35% residual solution in tap water is higher than that in ground water or sea water. Based on the data obtained from thermal analysis, it could be concluded that incorporating the residual solution form the wet oxidative degradation of cellulosic materials has no negative effect on the hydration of cement materials and consequently on the thermal stability of the final solid waste from during the disposal process

The effect of initial stress induced during the steel manufacturing process on the welding residual stress in multi-pass butt welding

Directory of Open Access Journals (Sweden)

Jeong-ung Park

2018-03-01

Full Text Available A residual stress generated in the steel structure is broadly categorized into initial residual stress during manufacturing steel material, welding residual stress caused by welding, and heat treatment residual stress by heat treatment. Initial residual stresses induced during the manufacturing process is combined with welding residual stress or heat treatment residual stress, and remained as a final residual stress. Because such final residual stress affects the safety and strength of the structure, it is of utmost importance to measure or predict the magnitude of residual stress, and to apply this point on the design of the structure. In this study, the initial residual stress of steel structures having thicknesses of 25 mm and 70 mm during manufacturing was measured in order to investigate initial residual stress (hereinafter, referred to as initial stress. In addition, thermal elastic plastic FEM analysis was performed with this initial condition, and the effect of initial stress on the welding residual stress was investigated. Further, the reliability of the FE analysis result, considering the initial stress and welding residual stress for the steel structures having two thicknesses, was validated by comparing it with the measured results. In the vicinity of the weld joint, the initial stress is released and finally controlled by the weld residual stress. On the other hand, the farther away from the weld joint, the greater the influence of the initial stress. The range in which the initial stress affects the weld residual stress was not changed by the initial stress. However, in the region where the initial stress occurs in the compressive stress, the magnitude of the weld residual compressive stress varies with the compression or tension of the initial stress. The effect of initial stress on the maximum compression residual stress was far larger when initial stress was considered in case of a thickness of 25 mm with a value of 180�

Effective deleting of residual photoconductivity in high-resistance layers GaAs

International Nuclear Information System (INIS)

Sadaev, B.S.; Kadirova, I.T.; Sharipov, E.I.

2004-01-01

Full text: The phenomenon of residual photoconductivity as the storage of optical memory (OM) represents practical interest in micro and optoelectronics. The finding - out of the nature OM represents undoubtedly and scientific interest. Now residual photoconductivity (RPC) is explained by potential barriers arising because of non-monocharacteristical of distribution components of the semiconductor or carriers of a current in volume. Depending on a nature non-monocharacteristical the time relaxation RPC changes in a wide limit. The special interest represents RPC created by impurity. In the given work the results of research of a nature RPC created photos by ionization of the filled centres of chrome in compensated epitaxilogic layers arsenide galls are resulted. Epitaxilogic layers were brought up by a vertical method ZFE. Highness was reached (achieved) by special indemnification of the residual donors deep acceptors of chrome. Substrates served n-GoAs. Lassitude of i-layers has made 70-80 microns. Specific resistance of layers has made (1/3) 108 om·sm. (T= 300 K). The structures were photosensitive as at low (T = 77 K) and at room temperatures. The photosensitivity of structures in impurity to a strip of absorption chrome (= 1,4 microns) was comparable (compared) with own. The researches show, that the structures have RPC. Size RPC the greatest ambassador impurity of illumination is carrying out photoionization Cr2 + - of the centres. That is established, RPC impurity of a photocurrent is effectively erased only at certain length of a wave of external illumination

Wetting of nonconserved residue-backbones: A feature indicative of aggregation associated regions of proteins.

Science.gov (United States)

Pradhan, Mohan R; Pal, Arumay; Hu, Zhongqiao; Kannan, Srinivasaraghavan; Chee Keong, Kwoh; Lane, David P; Verma, Chandra S

2016-02-01

Aggregation is an irreversible form of protein complexation and often toxic to cells. The process entails partial or major unfolding that is largely driven by hydration. We model the role of hydration in aggregation using "Dehydrons." "Dehydrons" are unsatisfied backbone hydrogen bonds in proteins that seek shielding from water molecules by associating with ligands or proteins. We find that the residues at aggregation interfaces have hydrated backbones, and in contrast to other forms of protein-protein interactions, are under less evolutionary pressure to be conserved. Combining evolutionary conservation of residues and extent of backbone hydration allows us to distinguish regions on proteins associated with aggregation (non-conserved dehydron-residues) from other interaction interfaces (conserved dehydron-residues). This novel feature can complement the existing strategies used to investigate protein aggregation/complexation. © 2015 Wiley Periodicals, Inc.

Effects of thermal treatment on mineralogy and heavy metal behavior in iron oxide stabilized air pollution control residues

DEFF Research Database (Denmark)

Sørensen, Mette Abildgaard; Bender-Koch, C.; Starckpoole, M. M.

2000-01-01

Stabilization of air pollution control residues by coprecipitation with ferrous iron and subsequent thermal treatment (at 600 and 900 °C) has been examined as a means to reduce heavy metal leaching and to improve product stability. Changes in mineralogy and metal binding were analyzed using various...... analytical and environmental techniques. Ferrihydrite was formed initially but transformed upon thermal treatment to more stable and crystalline iron oxides (maghemite and hematite). For some metals leaching studies showed more substantial binding after thermal treatment, while other metals either....... Thermal treatment of the stabilized residues produced structures with an inherently better iron oxide stability. However, the concentration of metals in the leachate generally increased as a consequence of the decreased solubility of metals in the more stable iron oxide structure....

Measured residual stresses in overlay pipe weldments removed from service

International Nuclear Information System (INIS)

Shack, W.J.

1985-02-01

Surface and throughwall residual stresses were measured on an elbow-to-pipe weldment that had been removed from the Hatch-2 reactor about a year after the application of a weld overlay. The results were compared with experimental measurements on three mock-up weldments and with finite-element calculations. The comparison shows that there are significant differences in the form and magnitude of the residual stress distributions. However, even after more than a year of service, the residual stresses over most of the inner surface of the actual plant weldment with an overlay were strongly compressive. 3 refs., 7 figs

On the residual stress and picostructure of titanium nitride films. Pt. 1

International Nuclear Information System (INIS)

Perry, A.J.; Valvoda, V.; Rafaja, D.; Williamson, D.L.; Sartwell, B.D.

1992-01-01

Titanium nitride films, dual energy ion implanted with argon or krypton, have been studied with a Seemann-Bohlin fine focus goniometer at grazing angles in the range 2-10. The implantation of 1% of either gas has little effect on the lattice parameters or the residual stress. It is thought that the gas atoms are on substitutional lattice sites and are associated with vacancies created during the implantation process. At 4% of implanted gas, it precipitates out in the form of bubbles; in the case of argon these are crystalline and their lattice parameter is close to that for solid argon as recorded in the literature. The lattice parameters and the residual stresses are affected slightly by the implantation: argon reduces the former and makes the latter more tensile, whereas the krypton has the opposite effects. It is thought that the difference in behavior is due to a difference in size of the bubbles or to the greater compressibility of argon

Spectroscopic Properties of Star-Forming Host Galaxies and Type Ia Supernova Hubble Residuals in a Nearly Unbiased Sample

Energy Technology Data Exchange (ETDEWEB)

D' Andrea, Chris B. [Univ. of Pennsylvania, Philadelphia, PA (United States); et al.

2011-12-20

We examine the correlation between supernova host galaxy properties and their residuals on the Hubble diagram. We use supernovae discovered during the Sloan Digital Sky Survey II - Supernova Survey, and focus on objects at a redshift of z < 0.15, where the selection effects of the survey are known to yield a complete Type Ia supernova sample. To minimize the bias in our analysis with respect to measured host-galaxy properties, spectra were obtained for nearly all hosts, spanning a range in magnitude of -23 < M_r < -17. In contrast to previous works that use photometric estimates of host mass as a proxy for global metallicity, we analyze host-galaxy spectra to obtain gas-phase metallicities and star-formation rates from host galaxies with active star formation. From a final sample of ~ 40 emission-line galaxies, we find that light-curve corrected Type Ia supernovae are ~ 0.1 magnitudes brighter in high-metallicity hosts than in low-metallicity hosts. We also find a significant (> 3{\\sigma}) correlation between the Hubble residuals of Type Ia supernovae and the specific star-formation rate of the host galaxy. We comment on the importance of supernova/host-galaxy correlations as a source of systematic bias in future deep supernova surveys.

Integrated assessment of soil quality after application of the biogas fermentation residues - a laboratory experiment

Science.gov (United States)

Telesiński, Arkadiusz; Cybulska, Krystyna; Płatkowski, Maciej; Stręk, Michał; Jarnuszewski, Grzegorz; Wrońska, Ilona; Mularewicz, Piotr; Kajdan, Tomasz; Biczak, Robert; Kołosowski, Paweł

2017-11-01

The aim of study was to determine the impact of three different biogas fermentation residues on some chemical and biochemical characteristics in sandy soil. The laboratory experiment was carried out on loamy sand. Residues were added to soil samples in the forms of pulp, drought, and granulate at dosages of 10, 50, and 100 g·kg-1. The reference was the soil sample without residues. On day 28, the content of macroelements and heavy metals was determined. In addition, on days 1, 7, 14, 28, and 56, the content of biomass and the activities of some hydrolases and oxidoreductases were assayed. Results showed that the application of all fermentation residues caused an increase in most of the chemical parameters. The highest impact on pH and the content of Ctot, Ntot, Stot, K, and P was observed in the soil treated with granulate, whereas the increase in the content of heavy metals was the highest after the drought application. The effect of biogas fermentation residues on all hydrolases and o-diphenol oxidase activities was mostly significant, but depended on the kind of residues and the day of experiment. Biomass content and the activity of dehydrogenase were increased in the whole experiment.

Effective Subcritical Butane Extraction of Bifenthrin Residue in Black Tea

Directory of Open Access Journals (Sweden)

Yating Zhang

2017-03-01

Full Text Available As a natural and healthy beverage, tea is widely enjoyed; however, the pesticide residues in tea leaves affect the quality and food safety. To develop a highly selective and efficient method for the facile removal of pesticide residues, the subcritical butane extraction (SBE technique was employed, and three variables involving temperature, time and extraction cycles were studied. The optimum SBE conditions were found to be as follows: extraction temperature 45 °C, extraction time 30 min, number of extraction cycles 1, and in such a condition that the extraction efficiency reached as high as 92%. Further, the catechins, theanine, caffeine and aroma components, which determine the quality of the tea, fluctuated after SBE treatment. Compared with the uncrushed leaves, pesticide residues can more easily be removed from crushed leaves, and the practical extraction efficiency was 97%. These results indicate that SBE is a useful method to efficiently remove the bifenthrin, and as appearance is not relevant in the production process, tea leaves should first be crushed and then extracted in order that residual pesticides are thoroughly removed.

Effective Subcritical Butane Extraction of Bifenthrin Residue in Black Tea.

Science.gov (United States)

Zhang, Yating; Gu, Lingbiao; Wang, Fei; Kong, Lingjun; Qin, Guangyong

2017-03-30

As a natural and healthy beverage, tea is widely enjoyed; however, the pesticide residues in tea leaves affect the quality and food safety. To develop a highly selective and efficient method for the facile removal of pesticide residues, the subcritical butane extraction (SBE) technique was employed, and three variables involving temperature, time and extraction cycles were studied. The optimum SBE conditions were found to be as follows: extraction temperature 45 °C, extraction time 30 min, number of extraction cycles 1, and in such a condition that the extraction efficiency reached as high as 92%. Further, the catechins, theanine, caffeine and aroma components, which determine the quality of the tea, fluctuated after SBE treatment. Compared with the uncrushed leaves, pesticide residues can more easily be removed from crushed leaves, and the practical extraction efficiency was 97%. These results indicate that SBE is a useful method to efficiently remove the bifenthrin, and as appearance is not relevant in the production process, tea leaves should first be crushed and then extracted in order that residual pesticides are thoroughly removed.

Characterization of Flame Cut Heavy Steel: Modeling of Temperature History and Residual Stress Formation

Science.gov (United States)

Jokiaho, T.; Laitinen, A.; Santa-aho, S.; Isakov, M.; Peura, P.; Saarinen, T.; Lehtovaara, A.; Vippola, M.

2017-12-01

Heavy steel plates are used in demanding applications that require both high strength and hardness. An important step in the production of such components is cutting the plates with a cost-effective thermal cutting method such as flame cutting. Flame cutting is performed with a controlled flame and oxygen jet, which burns the steel and forms a cutting edge. However, the thermal cutting of heavy steel plates causes several problems. A heat-affected zone (HAZ) is generated at the cut edge due to the steep temperature gradient. Consequently, volume changes, hardness variations, and microstructural changes occur in the HAZ. In addition, residual stresses are formed at the cut edge during the process. In the worst case, unsuitable flame cutting practices generate cracks at the cut edge. The flame cutting of thick steel plate was modeled using the commercial finite element software ABAQUS. The results of modeling were verified by X-ray diffraction-based residual stress measurements and microstructural analysis. The model provides several outcomes, such as obtaining more information related to the formation of residual stresses and the temperature history during the flame cutting process. In addition, an extensive series of flame cut samples was designed with the assistance of the model.

The effect of gamma irradiation on crude fibre NDF, ADF, and ADL of some Syrian agricultural residues

International Nuclear Information System (INIS)

Al-Masri, M.R.; Zarkawi, M.

1992-07-01

The effects of 150 KGy of gamma irradiation on crude fibre and its main components (cellulose, hemicellulose-cellulose and lignin) and on neutral detergent fibre (NDF), acid detergent lignin (ADL), and acid detergent fibre (ADF) were investigated. The results indicate that gamma irradiation decreased Cf content by 30%, 28%, 29%, and 17% for cottonwood, lentils straw, apple-tree pruning products and olive-oil cake, respectively. NDF values also decreased by 5%, 23%, 13% and 3% for, cottonwood, lentils straw, olive-oil cake and apple-tree pruning products respectively. Gamma irradiation (150 KGy) had no effects on ADF and ADL for lentils straw, apple-tree pruning products and olive-oil cake whereas, ADF decreased by 8.5% and ADL by 8.3 for cottonwood. Hemicellulose content increased by 12% for cottonwood while decreased by 54% for lentils straw and by 33% for apple-tree pruning products with no effects for olive-oil cake. Cellulose content decreased by 8.6% for cottonwood whereas no effects for the remaining residues were seen. Gamma irradiation treatment improved the nutritive value of the agriculture residues examined. The reduction in crude fibre content varies with the residue. (author). 15 refs., 5 tabs

Effects of organic additives on preferred plane and residual stress of copper electroplated on polyimide

International Nuclear Information System (INIS)

Kim, Jongsoo; Kim, Heesan

2010-01-01

Effects of the preferred plane and the residual stress of an electroplated copper on polyethylene glycol (PEG) and 3-N,N-dimethylaminodithiocarbamoyl-1-propanesulfonic acid (DPS) were studied. Polyimide film coated with sputtered copper was used as a substrate. Preferred plane, residual stress, and impurity level in the electroplated copper were measured by an X-ray diffractometry (XRD), calculated by Stoney's equation, and analyzed with secondary ion mass spectroscopy (SMS), respectively. With increasing the concentration of PEG, the preferred plane changed in the order (1 0 0) and (1 1 0) while with increasing the concentration of DPS, the preferred plane changed in the order (1 1 0), (1 0 0), and (1 1 1). Based on the modified preferred growth model, where the amount of additive adsorbed on a plane is newly assumed to be proportional to its surface energy in vacuum, the predicted preferred planes correspond to the experimental results. The residual stress of the electroplated copper depended on the type of additive as well as its concentration but was independent of the preferred plane. For example, PEG and DPS induced tensile and compressive residual stresses in the electroplated copper, respectively, and their magnitudes increased with their concentrations. The dependency of residual stress on the additives was explained by the incorporated additives into the electroplated copper.

Detection of pyridaben residue levels in hot pepper fruit and leaves by liquid chromatography-tandem mass spectrometry: effect of household processes.

Science.gov (United States)

Kim, Sung-Woo; Abd El-Aty, A M; Rahman, Md Musfiqur; Choi, Jeong-Heui; Choi, Ok-Ja; Rhee, Gyu-Seek; Chang, Moon-Ik; Kim, Heejung; Abid, Morad D N; Shin, Sung Chul; Shim, Jae-Han

2015-07-01

Following quick, easy, cheap, effective, rugged and safe (QuEChERS) and LC/MS/MS analysis, pyridaben residual levels were determined in unprocessed and processed hot pepper fruit and leaves. The linearities were satisfactory with determination coefficients (R(2)) in excess of 0.995 in processed and unprocessed pepper fruit and leaves. Recoveries at various concentrations were 79.9-105.1% with relative standard deviations ≤15%. The limits of quantitation of 0.003-0.012 mg/kg were very low compared with the maximum residue limits (2-5 mg/kg) set by the Ministry of Food and Drug Safety, Republic of Korea. The effects of various household processes, including washing, blanching, frying and drying under different conditions (water volume, blanching time and temperature) on residual concentrations were evaluated. Both washing and blanching (in combination with high water volume and time factor) significantly reduced residue levels in hot pepper fruit and leaves compared with other processes. In sum, the developed method was satisfactory and could be used to accurately detect residues in unprocessed and processed pepper fruit and leaves. It is recommended that pepper fruit/leaves be blanched after washing before being consumed to protect consumers from the negative health effects of detected pesticide residues. Copyright © 2014 John Wiley & Sons, Ltd.

The effect of residual stresses induced by prestraining on fatigue life of notched specimens

Science.gov (United States)

Sadeler, R.; Ozel, A.; Kaymaz, I.; Totik, Y.

2005-06-01

The effect of tensile prestraining-induced residual stress on the fatigue life of notched steel parts was investigated. The study was performed on AISI 4140 steel. Rotating bending fatigue tests were carried out on semicircular notched specimens with different notch radii in the as-quenched and tempered conditions. Metallography of the specimens was performed by means of light optical microscopy. The finite-element method was used to evaluate the residual stress distribution near the notch region. Fatigue tests revealed fatigue life improvement for notched specimens, which changes depending on the notch radii and applied stress. Scanning electron microscopy was used to examine the fracture surfaces of the specimens.

Thermal Adsorption Processing Of Hydrocarbon Residues

Directory of Open Access Journals (Sweden)

Sudad H. Al.

2017-04-01

Full Text Available The raw materials of secondary catalytic processes must be pre-refined. Among these refining processes are the deasphalting and demetallization including their thermo adsorption or thermo-contact adsorption variety. In oil processing four main processes of thermo-adsorption refining of hydrocarbon residues are used ART Asphalt Residual Treating - residues deasphaltizing 3D Discriminatory Destructive Distillation developed in the US ACT Adsorption-Contact Treatment and ETCC Express Thermo-Contact Cracking developed in Russia. ART and ACT are processes with absorbers of lift type reactor while 3D and ETCC processes are with an adsorbing reactor having ultra-short contact time of the raw material with the adsorbent. In all these processes refining of hydrocarbon residues is achieved by partial Thermo-destructive transformations of hydrocarbons and hetero-atomic compounds with simultaneous adsorption of the formed on the surface of the adsorbents resins asphaltene and carboids as well as metal- sulphur - and nitro-organic compounds. Demetallized and deasphalted light and heavy gas oils or their mixtures are a quality raw material for secondary deepening refining processes catalytic and hydrogenation cracking etc. since they are characterized by low coking ability and low content of organometallic compounds that lead to irreversible deactivation of the catalysts of these deepening processes.

The effect of heat treatment on the magnitude and composition of residual gas in sealed silica glass ampoules

Science.gov (United States)

Palosz, W.; Szofran, F. R.; Lehoczky, S. L.

1994-01-01

The residual gas pressure and composition in sealed silica glass ampoules as a function of different treatment procedures has been investigated. The dependence of the residual gas on the outgassing and annealing parameters has been determined. The effects of the fused silica brand, of the ampoule fabrication, and of post-outgassing procedures have been evaluated.

Effects of LSP on micro-structures and residual stresses in a 4 mm CLAM steel weld joints

Energy Technology Data Exchange (ETDEWEB)

Chen, Xizhang, E-mail: chenxizhang@wzu.edu.cn [School of Mechanical and Electrical Engineering, Wenzhou University., Wenzhou 325035 (China); School of Materials Science and Engineering, Jiangsu University, Zhenjiang 212013, Jiangsu (China); Fang, Yuanyuan [School of Materials Science and Engineering, Jiangsu University, Zhenjiang 212013, Jiangsu (China); Zhang, Shuyan; Kelleher, Joe F. [ISIS, Rutherford Appleton Laboratory, Chilton, Didcot OX11 0QX (United Kingdom); Zhou, Jianzhong [School of Mechanical Engineering, Jiangsu University, Zhenjiang 212013, Jiangsu (China)

2015-05-15

The effects of laser shock processing (LSP) on the distribution of residual stress and micro-structure of China Low Activation Martensitic (CLAM) steel weldment were investigated via neutron diffraction and optical microscope (OM). A pair of 4 mm CLAM steel plates joined by GTA welding. Special attention is paid to the generation of high level compressive residual stresses introduced by LSP. Residual stress in longitudinal, normal and transversal direction at weldment surface and longitudinal stress through thickness are evaluated via neutron diffraction. Compressive residual stress after LSP occurred at more than 90% areas within the weld joint, it is almost double the areas of compressive stress compare to weldment surface before LSP. The maximum compressive normal residual stress becomes to −183 MPa after LSP from −63 MPa before LSP. The Modification of surface micro-structures including weld zone (WZ), heat affected zone (HAZ) and base metal (BM) are also discussed. Results to date demonstrate that laser shock processing has been a great potential method for the improvement of mechanical performance of components.

A Laboratory Investigation on Shear Strength Behavior of Sandy Soil: Effect of Glass Fiber and Clinker Residue Content

Science.gov (United States)

Bouaricha, Leyla; Henni, Ahmed Djafar; Lancelot, Laurent

2017-12-01

A study was undertaken to investigate the shear strength parameters of treated sands reinforced with randomly distributed glass fibers by carrying out direct shear test after seven days curing periods. Firstly, we studied the fiber content and fiber length effect on the peak shear strength on samples. The second part gives a parametric analysis on the effect of glass fiber and clinker residue content on the shear strength parameters for two types of uniform Algerian sands having different particle sizes (Chlef sand and Rass sand) with an average relative density Dr = 50%. Finally, the test results show that the combination of glass fiber and clinker residue content can effectively improve the shear strength parameters of soil in comparison with unreinforced soil. For instance, there is a significant gain for the cohesion and friction angle of reinforced sand of Chlef. Compared to unreinforced sand, the cohesion for sand reinforced with different ratios of clinker residue increased by 4.36 to 43.08 kPa for Chlef sand and by 3.1 to 28.64 kPa for Rass sand. The feature friction angles increased from 38.73° to 43.01° (+4.28°), and after the treatment, clinker residue content of soil evaluated to 5% (WRC = 5%).

A Laboratory Investigation on Shear Strength Behavior of Sandy Soil: Effect of Glass Fiber and Clinker Residue Content

Directory of Open Access Journals (Sweden)

Bouaricha Leyla

2017-12-01

Full Text Available A study was undertaken to investigate the shear strength parameters of treated sands reinforced with randomly distributed glass fibers by carrying out direct shear test after seven days curing periods. Firstly, we studied the fiber content and fiber length effect on the peak shear strength on samples. The second part gives a parametric analysis on the effect of glass fiber and clinker residue content on the shear strength parameters for two types of uniform Algerian sands having different particle sizes (Chlef sand and Rass sand with an average relative density Dr = 50%. Finally, the test results show that the combination of glass fiber and clinker residue content can effectively improve the shear strength parameters of soil in comparison with unreinforced soil. For instance, there is a significant gain for the cohesion and friction angle of reinforced sand of Chlef. Compared to unreinforced sand, the cohesion for sand reinforced with different ratios of clinker residue increased by 4.36 to 43.08 kPa for Chlef sand and by 3.1 to 28.64 kPa for Rass sand. The feature friction angles increased from 38.73° to 43.01° (+4.28°, and after the treatment, clinker residue content of soil evaluated to 5% (WRC = 5%.

Investigation of effect of post weld heat treatment conditions on residual stress for ITER blanket shield blocks

Energy Technology Data Exchange (ETDEWEB)

Jung, Hun-Chea, E-mail: hcjung@nfri.re.kr [ITER Korea, National Fusion Research Institute, Daejeon (Korea, Republic of); Kim, Sa-Woong [ITER Korea, National Fusion Research Institute, Daejeon (Korea, Republic of); Lee, Yun-Hee [Division of Convergence Technology, Korea Research Institute of Standard and Science (KRISS), Daejeon (Korea, Republic of); Baek, Seung-Wook [Division of Industrial Metrology, Korea Research Institute of Standard and Science (KRISS), Daejeon (Korea, Republic of); Ha, Min-Su; Shim, Hee-Jin [ITER Korea, National Fusion Research Institute, Daejeon (Korea, Republic of)

2016-11-01

Highlights: • PWHT for ITER blanket shield block should be performed for dimensional stability. • Investigation of the effect of PWHT conditions on properties was performed. • Instrumented indentation method for evaluation of properties was used. • Residual stress and hardness decreased with increasing PWHT temperature. • Optimization of PWHT conditions would be needed for satisfaction of requirement. - Abstract: The blanket shield block (SB) shall be required the tight tolerance because SB interfaces with many components, such as flexible support keypads, First Wall (FW) support contact surfaces, FW central bolt, electrical strap contact surfaces and attachment inserts for both FW and Vacuum Vessel (VV). In order to fulfil the tight tolerance requirement, stress relieving shall be performed for dimensional stability after cover welding operation. In this paper, effect of Post Weld Heat Treatment (PWHT) conditions, temperature and holding time, was investigated on the residual stress and hardness. The 316L Stainless Steel (SS) was prepared and welded by manual TIG welding by using filler material with 2.4 mm of diameter. Welded 316L SS plate was machined to prepare the specimen for PWHT. PWHT was implemented at 250, 300, 400 °C for 2 and 3 h (400 °C only) and residual stress after relaxation were determined. The evaluation of residual stress and hardness for each specimen was carried out by instrumented indentation technique. The residual stress and hardness were decreased with increasing the heat treatment temperature and holding time.

Optimization of ethanol production from garcinia cambogia residues and the effects of its medicinal component on production yield

International Nuclear Information System (INIS)

Ma, H.; Zhang, F.

2017-01-01

Garcinia cambogia, a Chinese herbal medicine, was popular due to its effect for weight loss. The main medical component inside was determined to be hydroxycitric acid (HCA). To realize the resource technology of garcinia cambogia residue, Optimum ethanol production from residues was investigated, and the effects of remaining HCA on the ethanol yield were investigated. A Plackett-Burman experimental design was used to screen the significance of several influencing factors, and cellulase, yeast extract, and KH2PO4 were observed to exert important effects. The optimum ethanol fermentation conditions were determined through an orthogonal design to include a cellulase concentration of 100 U/g, a yeast extract concentration of 15 g/L, and a KH2PO4 concentration of 1.0 g/L. The ethanol concentration obtained under optimal conditions was 4.0 g/L. The remained HCA in the residues showed minimal influences on ethanol fermentation and could even increase ethanol yield at low concentrations. (author)

Effects of shot peening on the residual stress of welded SS400 steel

International Nuclear Information System (INIS)

Lee, Jong Man; Kim, Tae Hyung; Cheong, Seong Kyun; Lee, Seung Ho

2002-01-01

The fatigue life of structures is usually determined by welding zone. The tensile residual stress, which is induced by welding, reduces the fatigue life and fatigue strength of welded structures. If we remove the tensile residual stress or induce the compressive residual stress, the fatigue life of welded structures will be improved. The change of hardness and compressive residual stress of welded zone after shot peening was investigated in this paper. The results show that the hardness was increased by shot peening. The residual stress was reduced by shot peening

Applications of bauxite residue: A mini-review.

Science.gov (United States)

Verma, Ajay S; Suri, Narendra M; Kant, Suman

2017-10-01

Bauxite residue is the waste generated during alumina production by Bayer's process. The amount of bauxite residue (40-50 wt%) generated depends on the quality of bauxite ore used for the processing. High alkalinity and high caustic content in bauxite residue causes environmental risk for fertile soil and ground water contamination. The caustic (NaOH) content in bauxite residue leads to human health risks, like dermal problems and irritation to eyes. Moreover, disposal of bauxite residue requires a large area; such problems can only be minimised by utilising bauxite residue effectively. For two decades, bauxite residue has been used as a binder in cement industries and filler/reinforcement for composite materials in the automobile industry. Valuable metals and oxides, like alumina (Al 2 O 3 ), titanium oxide (TiO 2 ) and iron oxide Fe 2 O 3 , were extracted from bauxite residue to reduce waste. Bauxite residue was utilised in construction and structure industries to make geopolymers. It was also used in the making of glass-ceramics and a coating material. Recently bauxite residue has been utilised to extract rare earth elements like scandium (Sc), yttrium (Y), lanthanum (La), cerium (Ce), neodymium (Nd) and dysprosium (Dy). In this review article, the mineralogical characteristics of bauxite residue are summarised and current progresses on utilisation of bauxite residue in different fields of science and engineering are presented in detail.

Emotional Effects of Positive Forms of Communication

Directory of Open Access Journals (Sweden)

Светлана Валентиновна Ионова

2015-12-01

Full Text Available The article discusses the problem of emotional significance of a positive form of speech. Based on the methodology of emotions linguistics, linguoecology, communicative linguistics and the methods of description, comparison and discourse analysis, the author distinguishes some types of speech situations that demonstrate visible differences between positive expression of emotions and their content and the pragmatic effect. The difference between the notions of “positive communication” and “positive form of communication” is demonstrated. Special attention is given to the following types of positive emotional communication: tolerant emotional communication, emotional emphasis, emotional neglect, and emotional tabooing. The utterances in situations of real and textual communication demonstrate negative effects of statements expressed in a positive form and identify the specifics of positive forms of emotional communication in comparison with rational communication.

Effect of Elevated Temperature on the Residual Properties of Quartzite, Granite and Basalt Aggregate Concrete

Science.gov (United States)

Masood, A.; Shariq, M.; Alam, M. Masroor; Ahmad, T.; Beg, A.

2018-05-01

In the present study, experimental investigations have been carried out to determine the effect of elevated temperature on the residual properties of quartzite, granite and basalt aggregate concrete mixes. Ultrasonic pulse velocity and unstressed residual compressive strength tests on cube specimens have been conducted at ambient and after single heating-cooling cycle of elevated temperature ranging from 200 to 600 °C. The relationship between ultrasonic pulse velocity and residual compressive strength of all concrete mixes have been developed. Scanning electron microscopy was also carried out to study micro structure of quartzite, granite and basalt aggregate concrete subjected to single heating-cooling cycle of elevated temperature. The results show that the residual compressive strength of quartzite aggregate concrete has been found higher than granite and basalt aggregate concrete at ambient and at all temperatures. It has also been found that the loss of strength in concrete is due to the development of micro-cracks result in failure of cement matrix and coarse aggregate bond. Further, the basalt aggregate concrete has been observed lower strength due to low affinity with Portland cements ascribed to its ferro-magnesium rich mineral composition.

Effect of prior machining deformation on the development of tensile residual stresses in weld-fabricated nuclear components

International Nuclear Information System (INIS)

Prevey, P.S.; Mason, P.W.; Hornbach, D.J.; Molkenthin, J.P.

1996-01-01

Austenitic alloy weldments in nuclear systems may be subject to stress-corrosion cracking (SCC) failure if the sum of residual and applied stresses exceeds a critical threshold. Residual stresses developed by prior machining and welding may either accelerate or retard SCC, depending on their magnitude and sign. A combined x-ray diffraction and mechanical procedure was used to determine the axial and hoop residual stress and yield strength distributions into the inside-diameter surface of a simulated Alloy 600 penetration J-welded into a reactor pressure vessel. The degree of cold working and the resulting yield strength increase caused by prior machining and weld shrinkage were calculated from the line-broadening distributions. Tensile residual stresses on the order of +700 MPa were observed in both the axial and the hoop directions at the inside-diameter surface in a narrow region adjacent to the weld heat-affected zone. Stresses exceeding the bulk yield strength were found to develop due to the combined effects of cold working of the surface layers during initial machining and subsequent weld shrinkage. The residual stress and cold work distributions produced by prior machining were found to influence strongly the final residual stress state developed after welding

Review of radiation effects in solid-nuclear-waste forms

International Nuclear Information System (INIS)

Weber, W.J.

1981-09-01

Radiation effects on the stability of high-level nuclear waste (HLW) forms are an important consideration in the development of technology to immobilize high-level radioactive waste because such effects may significantly affect the containment of the radioactive waste. Since the required containment times are long (10 3 to 10 6 years), an understanding of the long-term cumulative effects of radiation damage on the waste forms is essential. Radiation damage of nuclear waste forms can result in changes in volume, leach rate, stored energy, structure/microstructure, and mechanical properties. Any one or combination of these changes might significantly affect the long-term stability of the nuclear waste forms. This report defines the general radiation damage problem in nuclear waste forms, describes the simulation techniques currently available for accelerated testing of nuclear waste forms, and reviews the available data on radiation effects in both glass and ceramic (primarily crystalline) waste forms. 76 references

Effects of sugammadex on incidence of postoperative residual neuromuscular blockade

DEFF Research Database (Denmark)

Brueckmann, B; Sasaki, N; Grobara, P

2015-01-01

BACKGROUND: This study aimed to investigate whether reversal of rocuronium-induced neuromuscular blockade with sugammadex reduced the incidence of residual blockade and facilitated operating room discharge readiness. METHODS: Adult patients undergoing abdominal surgery received rocuronium, followed...... by randomized allocation to sugammadex (2 or 4 mg kg(-1)) or usual care (neostigmine/glycopyrrolate, dosing per usual care practice) for reversal of neuromuscular blockade. Timing of reversal agent administration was based on the providers' clinical judgement. Primary endpoint was the presence of residual...... measured at PACU entry. Zero out of 74 sugammadex patients and 33 out of 76 (43.4%) usual care patients had TOF-Watch® SX-assessed residual neuromuscular blockade at PACU admission (odds ratio 0.0, 95% CI [0-0.06], P

Minor Forms in a Badlands Landscape Framework

Energy Technology Data Exchange (ETDEWEB)

Diaz-Hernandez, J. L.; Yepes, J.; Romero-Diaz, A.

2009-07-01

We describe and classify some medium-scale erosional morphologies in badlands areas. They have been categorized in three different types: A) Surficial forms on horizontal surfaces (soil surface crusts, cracks, popcorn) and walls (slips, pseudo-stalactites). B) Punctual fingerprints: rain impact and micro-collapses (dimples). C) Ruiniform morphologies (caves, shelters, residual pinnacles). The A type shapes are caused by damping-desiccation phenomena on clayey soils; morphologies on walls are due to laminar runoff on weak lithologies (clay, loam), also dubbed pseudo-spleleothemes. Their scale is centimetric-decimetric. B-Type forms may be an external passive process (impact) or an internal dynamic process (dimples) occurring in granular sediments inside shelters, in conditions of apparent calm, measuring up to a few centimetres. The caves and shelters of type C generally involve an excavation following stratification or jointing planes, while the residual pinnacles are vertical forms linked to advanced piping and fluting. Both forms are decametric in scale. (Author) 7 refs.

Minor Forms in a Badlands Landscape Framework

International Nuclear Information System (INIS)

Diaz-Hernandez, J. L.; Yepes, J.; Romero-Diaz, A.

2009-01-01

We describe and classify some medium-scale erosional morphologies in badlands areas. They have been categorized in three different types: A) Surficial forms on horizontal surfaces (soil surface crusts, cracks, popcorn) and walls (slips, pseudo-stalactites). B) Punctual fingerprints: rain impact and micro-collapses (dimples). C) Ruiniform morphologies (caves, shelters, residual pinnacles). The A type shapes are caused by damping-desiccation phenomena on clayey soils; morphologies on walls are due to laminar runoff on weak lithologies (clay, loam), also dubbed pseudo-spleleothemes. Their scale is centimetric-decimetric. B-Type forms may be an external passive process (impact) or an internal dynamic process (dimples) occurring in granular sediments inside shelters, in conditions of apparent calm, measuring up to a few centimetres. The caves and shelters of type C generally involve an excavation following stratification or jointing planes, while the residual pinnacles are vertical forms linked to advanced piping and fluting. Both forms are decametric in scale. (Author) 7 refs.

Effect of residual patient motion on dose distribution during image-guided robotic radiosurgery for skull tracking based on log file analysis

International Nuclear Information System (INIS)

Inoue, Mitsuhiro; Shiomi, Hiroya; Sato, Kengo

2014-01-01

The present study aimed to assess the effect of residual patient motion on dose distribution during intracranial image-guided robotic radiosurgery by analyzing the system log files. The dosimetric effect was analyzed according to the difference between the original and estimated dose distributions, including targeting error, caused by residual patient motion between two successive image acquisitions. One hundred twenty-eight treatments were analyzed. Forty-two patients were treated using the isocentric plan, and 86 patients were treated using the conformal (non-isocentric) plan. The median distance from the imaging center to the target was 55 mm, and the median interval between the acquisitions of sequential images was 79 s. The median translational residual patient motion was 0.1 mm for each axis, and the rotational residual patient motion was 0.1 deg for Δpitch and Δroll and 0.2 deg for Δyaw. The dose error for D 95 was within 1% in more than 95% of cases. The maximum dose error for D 10 to D 90 was within 2%. None of the studied parameters, including the interval between the acquisitions of sequential images, was significantly related to the dosimetric effect. The effect of residual patient motion on dose distribution was minimal. (author)

Effect of residual water content on the physico-chemical properties of sucralfate dried gel obtained by microwave drying.

Science.gov (United States)

Gainotti, Alessandro; Losi, Elena; Bettini, Ruggero; Colombo, Paolo; Sonvico, Fabio; Baroni, Daniela; Santi, Patrizia; Colombo, Gaia

2005-08-01

The purpose of this study was to investigate the physico-chemical characteristics of sucralfate humid gel dried by microwaves, in relation to the residual water content. Differential scanning calorimetry (DSC) allowed for the determination of the water state in sucralfate samples. Fourier-transform infrared (FT-IR) spectroscopy was used to monitor the changes in sucralfate gel structure induced by the microwave drying. A boundary value of total water content for sucralfate gel samples was found at 42% (w/w). Below this value only bound water was present, whereas above this value, the increase in total water was due to free water. In the physical form of gel, the strength of the coordination between sulfate anions and the positively charged aluminum hydroxide was dependent on the residual water content. The study of the sedimentation behavior of water suspensions prepared with dried sucralfate allowed for the evaluation of the retention of gel properties. We found that the microwave drying process affected the sedimentation of sucralfate dried gel suspensions independent of the residual water content: when suspensions were prepared from sucralfate dried gel powders containing more than 42% (w/w) of residual water, the sedimentation ratio was higher than 0.9. The non-gel powder suspension showed a sedimentation ratio of 0.68 +/- 0.02, whereas the sucralfate humid gel suspension did not sediment.

Estimating Residual Solids Volume In Underground Storage Tanks

International Nuclear Information System (INIS)

Clark, Jason L.; Worthy, S. Jason; Martin, Bruce A.; Tihey, John R.

2014-01-01

The Savannah River Site liquid waste system consists of multiple facilities to safely receive and store legacy radioactive waste, treat, and permanently dispose waste. The large underground storage tanks and associated equipment, known as the 'tank farms', include a complex interconnected transfer system which includes underground transfer pipelines and ancillary equipment to direct the flow of waste. The waste in the tanks is present in three forms: supernatant, sludge, and salt. The supernatant is a multi-component aqueous mixture, while sludge is a gel-like substance which consists of insoluble solids and entrapped supernatant. The waste from these tanks is retrieved and treated as sludge or salt. The high level (radioactive) fraction of the waste is vitrified into a glass waste form, while the low-level waste is immobilized in a cementitious grout waste form called saltstone. Once the waste is retrieved and processed, the tanks are closed via removing the bulk of the waste, chemical cleaning, heel removal, stabilizing remaining residuals with tailored grout formulations and severing/sealing external penetrations. The comprehensive liquid waste disposition system, currently managed by Savannah River Remediation, consists of 1) safe storage and retrieval of the waste as it is prepared for permanent disposition; (2) definition of the waste processing techniques utilized to separate the high-level waste fraction/low-level waste fraction; (3) disposition of LLW in saltstone; (4) disposition of the HLW in glass; and (5) closure state of the facilities, including tanks. This paper focuses on determining the effectiveness of waste removal campaigns through monitoring the volume of residual solids in the waste tanks. Volume estimates of the residual solids are performed by creating a map of the residual solids on the waste tank bottom using video and still digital images. The map is then used to calculate the volume of solids remaining in the waste tank. The ability to

Effect of cellulase producing fungi on plant residues degradation used as organic fertilizer

International Nuclear Information System (INIS)

Ibrahim, R.M.M

2009-01-01

Series of laboratory and field experiments were conducted at Soil microbiology Unit and Farm of soil and Water research department, Nuclear Research Center, Atomic Energy Authority, Egypt. Laboratory experiments revealed that between nine fungal strain, A. niger was the most potent cellulolytic fungus able to degrade many cellulosic sources (CP, CMC, and FP). Study the effect of cellulolytic fungi on degradation of plant residues used as organic fertilizer in addition to nitrogen fixing bacteria (symbiotically) on lupine growth, yield and nutrients uptake (Field experiment) had been carried out. This objective aims to recycling different plant residues in soil which is consistent with (sustainable development) and utilization of these organic residues as a single carbon source for cellulolytic fungi.Application of 15 N- tracer technique gave us the chance and opportunity to quantify the exact amounts of N derived from the different sources of nitrogen available to lupine plant under the effect of cellulolytic fungi on different plant residues.The obtained results could be summarized as following:I.Laboratory Technique Selection of the most potent cellulolytic fungi 1-Nine fungal strains of Aspergillus niger; Penicillium oxalicum; Trichoderma longibranchiatum; Aspergillus terreus; Aspergillus flavus; Alterrnaria sp.; Trichderma harzianum ; Rhizopus sp. and Syncephalastrum sp. obtained from different sources and tested for their cellulolytic activity. 2-Aspergillus niger and Pencillium oxalicum exhibited the highest cellulase productivity followed by Trichoderma longibranchiatum and Aspergillus terreus.3- fungal mixtures of the most potent four genera Aspergillus niger; Penicillium oxalicum; Trichoderma longibranchiatum and Aspergillus terreus found to have a lower cellulolytic activities for all substrates compared with single inoculation with A. niger.4-Highest FPase activities were exhibited by A. niger when filter paper (FP) used as a carbon source.5-A. niger is

EFFECTS OF MUCUNA ( MUCUNA UTILIS L.) RESIDUE ...

African Journals Online (AJOL)

The field experiment was conducted at two locations: University of Agriculture, Abeokuta (UNAAB) and Olowo-Papa (OP) in Ogun state both in Forest-savannah transition zone of Nigeria to investigate the response of three upland rice cultivars (O.sativa) to mucuna residue incorporation and Nitrogen (N) fertilizer and the ...

CO2 storage in depleted gas reservoirs: A study on the effect of residual gas saturation

Directory of Open Access Journals (Sweden)

Arshad Raza

2018-03-01

Full Text Available Depleted gas reservoirs are recognized as the most promising candidate for carbon dioxide storage. Primary gas production followed by injection of carbon dioxide after depletion is the strategy adopted for secondary gas recovery and storage practices. This strategy, however, depends on the injection strategy, reservoir characteristics and operational parameters. There have been many studies to-date discussing critical factors influencing the storage performance in depleted gas reservoirs while little attention was given to the effect of residual gas. In this paper, an attempt was made to highlight the importance of residual gas on the capacity, injectivity, reservoir pressurization, and trapping mechanisms of storage sites through the use of numerical simulation. The results obtained indicated that the storage performance is proportionally linked to the amount of residual gas in the medium and reservoirs with low residual fluids are a better choice for storage purposes. Therefore, it would be wise to perform the secondary recovery before storage in order to have the least amount of residual gas in the medium. Although the results of this study are useful to screen depleted gas reservoirs for the storage purpose, more studies are required to confirm the finding presented in this paper.

Peptides containing internal residues of pyroglutamic acid: proton NMR characteristics

International Nuclear Information System (INIS)

Khan, S.A.

1986-01-01

The proton NMR characteristics of internal pyroglutamic acid (Glp; 5-oxoproline) residues in seven tripeptides of the general structure Boc-Xxx-Glp-Yyy-NH 2 were studied. In general, the chemical shifts of several diagnostic protons moved downfield on going from the Glu-containing peptides (Boc-Xxx-Glu-Yyy-NH 2 ) to the corresponding Glp-containing peptides. The C-2 proton of the Xxx residue was shifted by about 1.1 ppm. The N-2 proton of the Yyy residue was shifted by about 0.5 ppm. The C-2 proton of the Glx residue itself was shifted by about 0.5 ppm. One of the Glx C-3 protons was also shifted by about 0.5 ppm, but the other remained essentially unchanged. Finally, the Glx C-4 protons were shifted by about 0.3 ppm. Internal Glu residues are readily converted chemically into internal Glp residues. This conversion also occurs as a side reaction during HP cleavage of the protecting group from Glu(OBzl) residues. The spontaneous fragmentation of serum proteins C3, C4 and λ 2 -macroglobulin under denaturing conditions is probably due to regioselective hydrolysis of an internal Glp residue formed in each of these proteins upon denaturation. These proton NMR characteristics may be useful in establishing the presence of internal Glp residues in synthetic and natural peptides

A 31-residue peptide induces aggregation of tau's microtubule-binding region in cells

Science.gov (United States)

Stöhr, Jan; Wu, Haifan; Nick, Mimi; Wu, Yibing; Bhate, Manasi; Condello, Carlo; Johnson, Noah; Rodgers, Jeffrey; Lemmin, Thomas; Acharya, Srabasti; Becker, Julia; Robinson, Kathleen; Kelly, Mark J. S.; Gai, Feng; Stubbs, Gerald; Prusiner, Stanley B.; Degrado, William F.

2017-09-01

The self-propagation of misfolded conformations of tau underlies neurodegenerative diseases, including Alzheimer's. There is considerable interest in discovering the minimal sequence and active conformational nucleus that defines this self-propagating event. The microtubule-binding region, spanning residues 244-372, reproduces much of the aggregation behaviour of tau in cells and animal models. Further dissection of the amyloid-forming region to a hexapeptide from the third microtubule-binding repeat resulted in a peptide that rapidly forms fibrils in vitro. We show that this peptide lacks the ability to seed aggregation of tau244-372 in cells. However, as the hexapeptide is gradually extended to 31 residues, the peptides aggregate more slowly and gain potent activity to induce aggregation of tau244-372 in cells. X-ray fibre diffraction, hydrogen-deuterium exchange and solid-state NMR studies map the beta-forming region to a 25-residue sequence. Thus, the nucleus for self-propagating aggregation of tau244-372 in cells is packaged in a remarkably small peptide.

Prediction of interface residue based on the features of residue interaction network.

Science.gov (United States)

Jiao, Xiong; Ranganathan, Shoba

2017-11-07

Protein-protein interaction plays a crucial role in the cellular biological processes. Interface prediction can improve our understanding of the molecular mechanisms of the related processes and functions. In this work, we propose a classification method to recognize the interface residue based on the features of a weighted residue interaction network. The random forest algorithm is used for the prediction and 16 network parameters and the B-factor are acting as the element of the input feature vector. Compared with other similar work, the method is feasible and effective. The relative importance of these features also be analyzed to identify the key feature for the prediction. Some biological meaning of the important feature is explained. The results of this work can be used for the related work about the structure-function relationship analysis via a residue interaction network model. Copyright © 2017 Elsevier Ltd. All rights reserved.

Analysis and characterization of plutonium in pyrochemical salt residues

International Nuclear Information System (INIS)

Haschke, John M.; Phillips, Alan G.

2000-01-01

Quantitative measurement of hydrogen produced during salt-catalyzed hydrolysis of plutonium in pyrochemical salt residues show that the metal is present in concentrations of 10 ± 5 mass%. The analytical method is based on stoichiometric reaction of metal with water to form plutonium monoxide monohydride (PuOH) and hydrogen. Results of a kinetic model developed to describe the observed time dependence of the hydrolysis rate shows that metal is present predominately as particles with essentially spherical geometries and diameters near 1 mm. The presence of smaller metallic particles cannot be verified or excluded. Plutonium concentrations measured for residues stored in different configurations suggest that a sizable fraction of the metal has oxidized during storage. Application of the hydrolysis method in determining concentrations and dimensions of metallic plutonium in other nuclear waste forms is proposed

Protein Coexpression Using FMDV 2A: Effect of “Linker” Residues

Directory of Open Access Journals (Sweden)

Ekaterina Minskaia

2013-01-01

Full Text Available Many biomedical applications absolutely require, or are substantially enhanced by, coexpression of multiple proteins from a single vector. Foot-and-mouth disease virus 2A (F2A and “2A-like” sequences (e.g., Thosea asigna virus 2A; T2A are used widely for this purpose since multiple proteins can be coexpressed by linking open reading frames (ORFs to form a single cistron. The activity of F2A “cleavage” may, however, be compromised by both the use of shorter versions of F2A and the sequences (derived from multiple-purpose cloning sites used to link F2A to the upstream protein. To characterise these effects, different lengths of F2A and T2A were inserted between green and cherry fluorescent proteins. Mutations were introduced in the linker region immediately upstream of both F2A- and T2A-based constructs and activities determined using both cell-free translation systems and transfected cells. In shorter versions of F2A, activity may be affected by both the C-terminal sequence of the protein upstream and, equally strikingly, the residues immediately upstream introduced during cloning. Mutations significantly improved activity for shorter versions of F2A but could decrease activity in the case of T2A. These data will aid the design of cloning strategies for the co-expression of multiple proteins in biomedical/biotechnological applications.

Ensemble Kalman filtering with residual nudging

KAUST Repository

Luo, X.

2012-10-03

Covariance inflation and localisation are two important techniques that are used to improve the performance of the ensemble Kalman filter (EnKF) by (in effect) adjusting the sample covariances of the estimates in the state space. In this work, an additional auxiliary technique, called residual nudging, is proposed to monitor and, if necessary, adjust the residual norms of state estimates in the observation space. In an EnKF with residual nudging, if the residual norm of an analysis is larger than a pre-specified value, then the analysis is replaced by a new one whose residual norm is no larger than a pre-specified value. Otherwise, the analysis is considered as a reasonable estimate and no change is made. A rule for choosing the pre-specified value is suggested. Based on this rule, the corresponding new state estimates are explicitly derived in case of linear observations. Numerical experiments in the 40-dimensional Lorenz 96 model show that introducing residual nudging to an EnKF may improve its accuracy and/or enhance its stability against filter divergence, especially in the small ensemble scenario.

Effect of residual stress on fatigue crack propagation at 200 C in a welded joint austenitic stainless steel - ferritic steel

International Nuclear Information System (INIS)

Zahouane, A.I.; Gauthier, J.P.; Petrequin, P.

1988-01-01

Fatigue resistance of heterogeneous welded joints between austenitic stainless steels and ferritic steels is evaluated for reactor components and more particularly effect of residual stress on fatigue crack propagation in a heterogeneous welded joint. Residual stress is measured by the hole method in which a hole is drilled through the center of a strain gage glued the surface of the materials. In the non uniform stress field a transmissibility function is used for residual stress calculation. High compression residual stress in the ferritic metal near the interface ferritic steel/weld slow down fatigue crack propagation. 5 tabs., 15 figs., 19 refs [fr

Effects of storage and processing on residue levels of chlorpyrifos in soybeans.

Science.gov (United States)

Zhao, Liuwei; Ge, Jing; Liu, Fengmao; Jiang, Naiwen

2014-05-01

The residue levels of chlorpyrifos in soybeans during storage and processing were investigated. Soybeans were treated with chlorpyrifos aqueous solution and placed in a sealed plastic container. The residue of chlorpyrifos was determined in soybeans at six time points within 0 and 112days during storage and oil processing of the soybeans was conducted. The analysis of the residues of chlorpyrifos was carried out by gas chromatography-mass spectrometry (GC-MS). Results show that the dissipation of chlorpyrifos in soybeans is about 62% during the storage period. Moreover, the carryover of the residues from soybeans into oil is found to be related to the processing methods. Processing factor, which is defined as the ratio of chlorpyrifos residue concentration in oil sample to that in the soybean samples, was 11 and 0.25 after cold and hot pressing, respectively. Copyright © 2013 Elsevier Ltd. All rights reserved.

Investigation of Performance and Residual Stress Generation of AlSi10Mg Processed by Selective Laser Melting

Directory of Open Access Journals (Sweden)

Lianfeng Wang

2018-01-01

Full Text Available During the selective laser melting (SLM process, the scanned layers are subjected to rapid thermal cycles. By working on the mechanical properties, residual stress, and microstructure, the high-temperature gradients can have significant effect on the proper functioning and the structural integrity of built parts. This work presents a comprehensive study on the scanning path type and preheating temperature for AlSi10Mg alloy during SLM. According to the results, SLM AlSi10Mg parts fabricated in chessboard scanning strategy have higher mechanical properties or at least comparable to the parts fabricated in uniformity scanning strategy. In the SLM processing, the residual stress in different parts of the specimen varies with temperature gradient, and the residual stress at the edge of the specimen is obviously larger than that at the center. Under the chessboard scanning and preheating temperature 160°C, the residual stress in each direction of the specimens reaches the minimum. Under different forming processes, the morphology of the microstructure is obviously different. With the increase of preheating temperature, the molten pool in the side surface is obviously elongated and highly unevenly distributed. From the coupling relationship between the residual stress and microstructure, it can be found that the microstructure of top surface is affected by residual stresses σx and σy. But the side surface is mainly governed by residual stress σy; moreover, the greater the residual stress, the more obvious the grain tilt. In the XY and XZ surfaces, the scanning strategy has little influence on the tilt angle of the grain. But, the tilt angle and morphology of the microstructure are obviously affected by the preheating temperature. The results show that the residual stresses can effectively change the properties of the materials under the combined influence of scanning strategy and preheating temperature.

Effects of Ultrasonic Nanocrystal Surface Modification on the Residual Stress, Microstructure, and Corrosion Resistance of 304 Stainless Steel Welds

Science.gov (United States)

Ye, Chang; Telang, Abhishek; Gill, Amrinder; Wen, Xingshuo; Mannava, Seetha R.; Qian, Dong; Vasudevan, Vijay K.

2018-03-01

In this study, ultrasonic nanocrystal surface modification (UNSM) of 304 stainless steel welds was carried out. UNSM effectively eliminates the tensile stress generated during welding and imparts beneficial compressive residual stresses. In addition, UNSM can effectively refine the grains and increase hardness in the near-surface region. Corrosion tests in boiling MgCl2 solution demonstrate that UNSM can significantly improve the corrosion resistance due to the compressive residual stresses and changes in the near-surface microstructure.

REPLACEMENT OF TRYPTOPHAN RESIDUES IN HALOALKANE DEHALOGENASE REDUCES HALIDE BINDING AND CATALYTIC ACTIVITY

NARCIS (Netherlands)

KENNES, C; PRIES, F; KROOSHOF, GH; BOKMA, E; Kingma, Jacob; JANSSEN, DB

1995-01-01

Haloalkane dehalogenase catalyzes the hydrolytic cleavage of carbon-halogen bonds in short-chain haloalkanes. Two tryptophan residues of the enzyme (Trp125 and Trp175) form a halide-binding site in the active-site cavity, and were proposed to play a role in catalysis. The function of these residues

The Effect of Residual Stress on the Electromechanical Behavior of Electrostatic Microactuators

Directory of Open Access Journals (Sweden)

Ming-Hung Hsu

2008-01-01

Full Text Available This work simulates the nonlinear electromechanical behavior of different electrostatic microactuators. It applies the differential quadrature method, Hamilton's principle, and Wilson-θ integration method to derive the equations of motion of electrostatic microactuators and find a solution to these equations. Nonlinear equation difficulties are overcome by using the differential quadrature method. The stresses of electrostatic actuators are determined, and the residual stress effects of electrostatic microactuators are simulated.

The influence of long-range residual stress on plastic collapse of pressurised pipes with and without flaws

International Nuclear Information System (INIS)

Wu, Gui-Yi; Smith, David J.; Pavier, Martyn J.

2013-01-01

Structural integrity assessments of pressurised pipes include plastic collapse as a potential failure mode. This paper uses analytical and numerical models to explore the effect of the end conditions of the pipe on the collapse pressure. The pipe is open-ended and two bounding conditions are addressed: one where axial loading is applied to the ends of the pipe and the other where a fixed axial displacement is applied. The fixed axial displacement condition represents long-range or fit-up residual stress. It is common practice to treat long-range residual stress in the same way as axial loading, leading to the conclusion that such long-range residual stress reduces the collapse pressure. Pipes in a number of states are considered: pipes with no flaws, pipes with fully circumferential flaws and pipes with part circumferential flaws. The flaws consist of either a crack or a slot on the external surface of the pipe. For the axial load condition, the collapse pressure for a flawed pipe is reduced when higher magnitudes of tensile or compressive axial loads are applied. For the fixed displacement condition however, the magnitude of the displacement may have little or no effect on the collapse pressure. The results of the work indicate that substantially conservative assessments may be made of the collapse pressures of pipes containing flaws, when long-range residual stress is taken to be a form of axial loading. -- Highlights: • The effect of end conditions on the collapse pressure of a pipe has been explored. • Fixed displacement conditions represent long-range residual stress. • Long-range residual stress is commonly thought to contribute to plastic collapse. • We show long-range residual stress has no influence on collapse for flawed pipes. • It is therefore possible to reduce conservatism in structural integrity assessment

Effects of residual hydrogen in sputtering atmosphere on structures and properties of amorphous In-Ga-Zn-O thin films

Energy Technology Data Exchange (ETDEWEB)

Tang, Haochun; Ishikawa, Kyohei; Ide, Keisuke [Materials and Structures Laboratory, Tokyo Institute of Technology, 4259 Nagatsuta, Midori-ku, Yokohama 226-8503 (Japan); Hiramatsu, Hidenori; Hosono, Hideo; Kamiya, Toshio, E-mail: kamiya.t.aa@m.titech.ac.jp [Materials and Structures Laboratory, Tokyo Institute of Technology, 4259 Nagatsuta, Midori-ku, Yokohama 226-8503 (Japan); Materials Research Center for Element Strategy, Tokyo Institute of Technology, 4259 Nagatsuta, Midori-ku, Yokohama 226-8503 (Japan); Ueda, Shigenori [National Institute for Materials Science, 1-2-1 Sengen, Tsukuba-city, Ibaraki 305-0047 (Japan); Ohashi, Naoki [Materials Research Center for Element Strategy, Tokyo Institute of Technology, 4259 Nagatsuta, Midori-ku, Yokohama 226-8503 (Japan); National Institute for Materials Science, 1-2-1 Sengen, Tsukuba-city, Ibaraki 305-0047 (Japan); Kumomi, Hideya [Materials Research Center for Element Strategy, Tokyo Institute of Technology, 4259 Nagatsuta, Midori-ku, Yokohama 226-8503 (Japan)

2015-11-28

We investigated the effects of residual hydrogen in sputtering atmosphere on subgap states and carrier transport in amorphous In-Ga-Zn-O (a-IGZO) using two sputtering systems with different base pressures of ∼10{sup −4} and 10{sup −7 }Pa (standard (STD) and ultrahigh vacuum (UHV) sputtering, respectively), which produce a-IGZO films with impurity hydrogen contents at the orders of 10{sup 20} and 10{sup 19 }cm{sup −3}, respectively. Several subgap states were observed by hard X-ray photoemission spectroscopy, i.e., peak-shape near-valence band maximum (near-VBM) states, shoulder-shape near-VBM states, peak-shape near-conduction band minimum (near-CBM) states, and step-wise near-CBM states. It was confirmed that the formation of these subgap states were affected strongly by the residual hydrogen (possibly H{sub 2}O). The step-wise near-CBM states were observed only in the STD films deposited without O{sub 2} gas flow and attributed to metallic In. Such step-wise near-CBM state was not detected in the other films including the UHV films even deposited without O{sub 2} flow, substantiating that the metallic In is segregated by the strong reduction effect of the hydrogen/H{sub 2}O. Similarly, the density of the near-VBM states was very high for the STD films deposited without O{sub 2}. These films had low film density and are consistent with a model that voids in the amorphous structure form a part of the near-VBM states. On the other hand, the UHV films had high film densities and much less near-VBM states, keeping the possibility that some of the near-VBM states, in particular, of the peak-shape ones, originate from –OH and weakly bonded oxygen. These results indicate that 2% of excess O{sub 2} flow is required for the STD sputtering to compensate the effects of the residual hydrogen/H{sub 2}O. The high-density near-VBM states and the metallic In segregation deteriorated the electron mobility to 0.4 cm{sup 2}/(V s)

Evaluation of residue-residue contact predictions in CASP9

KAUST Repository

Monastyrskyy, Bohdan

2011-01-01

This work presents the results of the assessment of the intramolecular residue-residue contact predictions submitted to CASP9. The methodology for the assessment does not differ from that used in previous CASPs, with two basic evaluation measures being the precision in recognizing contacts and the difference between the distribution of distances in the subset of predicted contact pairs versus all pairs of residues in the structure. The emphasis is placed on the prediction of long-range contacts (i.e., contacts between residues separated by at least 24 residues along sequence) in target proteins that cannot be easily modeled by homology. Although there is considerable activity in the field, the current analysis reports no discernable progress since CASP8.

Residual magnetic field in rotary machines; Campo magnetico residual en maquinas rotatorias

Energy Technology Data Exchange (ETDEWEB)

Gonzalez V, Esteban A; Apanco R, Marcelino [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico)

2007-07-01

The residual magnetism is a phenomenon in which the magnetic dipoles of a substance are oriented in a certain degree. On the other hand, when internal forces exist capable of aligning elementary magnetic dipoles of a material, a permanent magnet is obtained. Just as in a conductor or in a material, in the elements of a rotary electrical machine magnetic fields can be induced that produce a residual magnetism or magnetization. In the rotary electrical machines, the magnetization phenomenon causes serious problems, such as the generation of induced currents that propitiate the mechanical wear in bearings, collars, trunnions and inclusive in the shaft, by effects known as pitting, frosting and spark tracks, as well as erroneous readings in vibration and temperature sensors, that in some cases can cause the shut down of the machine. In this article are presented the general concepts on the residual magnetism in rotary electrical machines, the causes that originate it and the problems that arises, as well as the demagnetization of the components that have residual magnetic field. The results obtained by the area of Electrical Equipment of the Instituto de Investigaciones Electricas are revised, during the execution of activities related to the measurement and elimination of the residual magnetic field in rotary electrical machines. [Spanish] El magnetismo residual es un fenomeno en el que los dipolos magneticos de una sustancia se encuentran orientados en un grado determinado. Por otro lado, cuando existen fuerzas internas capaces de alinear los dipolos magneticos elementales de un material, se tiene un iman permanente. Al igual que en un conductor o un material, en los elementos de una maquina electrica rotatoria se pueden inducir campos magneticos que producen un magnetismo residual o magnetizacion. En las maquinas electricas rotatorias, el fenomeno de magnetizacion causa graves problemas, como la generacion de corrientes inducidas que propician el desgaste mecanico

The effects of forest residual debris disposal on perennial grass emergence, growth, and survival in a ponderosa pine ecotone

Science.gov (United States)

Darin J. Law; Peter F. Kolb

2007-01-01

Soil surface conditions can have profound effects on plant seedling emergence and subsequent seedling survival. To test the hypothesis that different soil-surface treatments with logging residue affect range grass seedling emergence and survival, 6 alternative forest-residual treatments were established in the summer of 1998 following thinning of mature trees from...

Reactivity of Athabasca residue and of its SARA fractions during residue hydroconversion

Energy Technology Data Exchange (ETDEWEB)

Verstraete, J.; Danial-Fortain, P.; Gauthier, T.; Merdrignac, I. [IFP-Lyon, Vermaison (France); Budzinski, H. [Bordeaux Univ. (France). ISM-LPTC, UMR CNRS

2009-07-01

Residue conversion processes are becoming increasingly important because of the declining market for residual fuel oil and a greater demand for middle distillates. Ebullated-bed hydroconversion is a commercially proven technology for converting heavy feedstocks with high amounts of impurities. The process enables the conversion of atmospheric or vacuum residues at temperatures up to 440 degrees C, and at liquid hourly space velocity (LHSV) conditions in the range of 0.15 to 0.5 per hour. A 540 degrees C conversion of up to 80 weight per cent can be achieved under these conditions. This paper reported on a research study conducted at IFP Lyon in which the residue hydroconversion in a large-scale ebullated bed bench unit was investigated to determine the impact of operating conditions and feed properties on yield and product qualities. Hydrogen was added to the feed in the bench units to keep a high hydrogen partial pressure and favour the catalytic hydroconversion reactions. In a typical test, the reactor was fed with 50 g of feedstock and 0.45 g of crushed equilibrium industrial NiMo catalyst, pressurized hydrogen and quickly heated at the reaction temperature. This paper also discussed the conversion of Athabasca bitumen residue in the large-scale pilot plant and also in the small scale batch reactor. The effect of operating temperature and space velocity was examined. The reactivity of the saturates, aromatics, resins and asphaltenes (SARA) fractions of the bitumen was studied separately in order to better understand the conversion mechanisms and reactivities. The Athabasca bitumen feed and SARA fractions were also analyzed in terms of standard petroleum analysis, SARA fractionation, elemental analysis, size exclusion chromatography (SEC) and 13C NMR. Hydroconversion experiments were conducted in the batch unit at different reaction temperatures and reaction times. A comparison of small-scale batch results with those obtained with the continuous large-scale bench

Effect of laser shock peening on residual stress and fatigue life of clad 2024 aluminium sheet containing scribe defects

International Nuclear Information System (INIS)

Dorman, M.; Toparli, M.B.; Smyth, N.; Cini, A.; Fitzpatrick, M.E.; Irving, P.E.

2012-01-01

Highlights: ► Effect of laser peen intensity on local residual stress fields in 2024 aluminium. ► Peening induces significant changes in surface topography and local hardness. ► Residual stress at peen spot centre in tension, spot overlap in compression. ► Notched fatigue lives increased; crack morphology correlated to residual stress field. ► Large peening power densities can cause fatigue life reduction in notched samples. - Abstract: Laser peening at a range of power densities has been applied to 2 mm-thick sheets of 2024 T351 aluminium. The induced residual stress field was measured using incremental hole drilling and synchrotron X-ray diffraction techniques. Fatigue samples were subjected to identical laser peening treatments followed by scribing at the peen location to introduce stress concentrations, after which they were fatigue tested. The residual stresses were found to be non-biaxial: orthogonal to the peen line they were tensile at the surface, moving into the desired compression with increased depth. Regions of peen spot overlap were associated with large compression strains; the centre of the peen spot remaining tensile. Fatigue lives showed moderate improvement over the life of unpeened samples for 50 μm deep scribes, and slight improvement for samples with 150 μm scribes. Use of the residual stress intensity K resid approach to calculate fatigue life improvement arising from peening was unsuccessful at predicting the relative effects of the different peening treatments. Possible reasons for this are explored.

Dissimilar friction stir welds in AA5083-AA6082: The effect of process parameters on residual stress

International Nuclear Information System (INIS)

Steuwer, A.; Peel, M.J.; Withers, P.J.

2006-01-01

The effect of tool traverse and rotation speeds on the residual stresses are quantified for welds between non-age-hardening AA5083 and age-hardening AA6082 and compared to single alloy joints made from each of the two constituents. The residual stresses have been characterised non-destructively by neutron diffraction and synchrotron X-ray diffraction. The region around the weld line was characterised by significant tensile residual stress fields which are balanced by compressive stresses in the parent material. The rotation speed of the tool has been found to have a substantially greater influence than the transverse speed on the properties and residual stresses in the welds, particularly on the AA5083 side where the location of the peak stress moves from the stir zone to beyond the edge of the tool shoulder. The changes in residual stress are related to microstructural and hardness changes as determined in a previous study . In particular the larger stresses under the weld tool on the AA5083 side compared to the AA6082 side are related to a transient reduction in yield stress due to dissolution of the hardening precipitates during welding prior to natural aging after welding

Identification of residue pairing in interacting β-strands from a predicted residue contact map.

Science.gov (United States)

Mao, Wenzhi; Wang, Tong; Zhang, Wenxuan; Gong, Haipeng

2018-04-19

Despite the rapid progress of protein residue contact prediction, predicted residue contact maps frequently contain many errors. However, information of residue pairing in β strands could be extracted from a noisy contact map, due to the presence of characteristic contact patterns in β-β interactions. This information may benefit the tertiary structure prediction of mainly β proteins. In this work, we propose a novel ridge-detection-based β-β contact predictor to identify residue pairing in β strands from any predicted residue contact map. Our algorithm RDb 2 C adopts ridge detection, a well-developed technique in computer image processing, to capture consecutive residue contacts, and then utilizes a novel multi-stage random forest framework to integrate the ridge information and additional features for prediction. Starting from the predicted contact map of CCMpred, RDb 2 C remarkably outperforms all state-of-the-art methods on two conventional test sets of β proteins (BetaSheet916 and BetaSheet1452), and achieves F1-scores of ~ 62% and ~ 76% at the residue level and strand level, respectively. Taking the prediction of the more advanced RaptorX-Contact as input, RDb 2 C achieves impressively higher performance, with F1-scores reaching ~ 76% and ~ 86% at the residue level and strand level, respectively. In a test of structural modeling using the top 1 L predicted contacts as constraints, for 61 mainly β proteins, the average TM-score achieves 0.442 when using the raw RaptorX-Contact prediction, but increases to 0.506 when using the improved prediction by RDb 2 C. Our method can significantly improve the prediction of β-β contacts from any predicted residue contact maps. Prediction results of our algorithm could be directly applied to effectively facilitate the practical structure prediction of mainly β proteins. All source data and codes are available at http://166.111.152.91/Downloads.html or the GitHub address of https://github.com/wzmao/RDb2C .

Effects of thinning, residue mastication, and prescribed fire on soil and nutrient budgets in a Sierra Nevada mixed-conifer forest

Science.gov (United States)

The effects of thinning followed by residue mastication (THIN), prescribed fire (BURN), and thinning plus residue mastication plus burning (T+B) on nutrient budgets and resin-based (plant root simulator [PRS] probe) measurements of soil nutrient availability in a mixed-conifer forest were measured. ...

Effects of thinning, residue mastication, and prescribed fire on soil and nutrient budgets in a Sierra Nevada mixed conifer forest

Science.gov (United States)

The effects of thinning followed by residue mastication (THIN), prescribed fire (BURN), and thinning plus residue mastication plus burning (T+B) on nutrient budgets and resin-based (plant root simulator [PRS] probe) measurements of soil nutrient availability in a mixed-conifer forest were measured. ...

Residues from waste incineration. Final report

Energy Technology Data Exchange (ETDEWEB)

Astrup, T.; Juul Pedersen, A.; Hyks, J.; Frandsen, F.J.

2009-08-15

The overall objective of the project was to improve the understanding of the formation and characteristics of residues from waste incineration. This was done focusing on the importance of the waste input and the operational conditions of the furnace. Data and results obtained from the project have been discussed in this report according to the following three overall parts: i) mass flows and element distribution, ii) flue gas/particle partitioning and corrosion/deposition aspects, and iii) residue leaching. This has been done with the intent of structuring the discussion while tacitly acknowledging that these aspects are interrelated and cannot be separated. Overall, it was found that the waste input composition had significant impact of the characteristics of the generated residues. A similar correlation between operational conditions and residue characteristics could not be observed. Consequently, the project recommend that optimization of residue quality should focus on controlling the waste input composition. The project results showed that including specific waste materials (and thereby also excluding the same materials) may have significant effects on the residue composition, residue leaching, aerosol and deposit formation.It is specifically recommended to minimize Cl in the input waste. Based on the project results, it was found that a significant potential for optimization of waste incineration exist. (author)

Contribution of microorganisms to non-extractable residue formation during biodegradation of ibuprofen in soil

Energy Technology Data Exchange (ETDEWEB)

Nowak, Karolina M., E-mail: karolina.nowak@ufz.de [UFZ, Helmholtz Centre for Environmental Research, Department of Environmental Biotechnology, Permoserstraße 15, 04318 Leipzig (Germany); Department of Environmental Biology and Chemodynamics, Institute for Environmental Research (Biology V), RWTH Aachen University, Worringerweg 1, 52074 Aachen (Germany); Girardi, Cristobal; Miltner, Anja [UFZ, Helmholtz Centre for Environmental Research, Department of Environmental Biotechnology, Permoserstraße 15, 04318 Leipzig (Germany); Gehre, Matthias [UFZ, Helmholtz Centre for Environmental Research, Department of Isotope Biogeochemistry, Permoserstraße 15, 04318 Leipzig (Germany); Schäffer, Andreas [Department of Environmental Biology and Chemodynamics, Institute for Environmental Research (Biology V), RWTH Aachen University, Worringerweg 1, 52074 Aachen (Germany); Kästner, Matthias [UFZ, Helmholtz Centre for Environmental Research, Department of Environmental Biotechnology, Permoserstraße 15, 04318 Leipzig (Germany)

2013-02-15

Non-extractable residues (NER) formed during biodegradation of organic contaminants in soil are considered to be mainly composed of parent compounds or their primary metabolites with hazardous potential. However, in the case of biodegradable organic compounds, the soil NER may also contain microbial biomass components, for example fatty acids (FA) and amino acids (AA). After cell death, these biomolecules are subsequently incorporated into non-living soil organic matter (SOM) and are stabilised ultimately forming hardly extractable residues of biogenic origin. We investigated biodegradation of {sup 13}C{sub 6}-ibuprofen, in particular the metabolic incorporation of the {sup 13}C-label into FA and AA and their fate in soil over 90 days. {sup 13}C-FA and {sup 13}C-AA amounts in the living microbial biomass fraction initially increased, then decreased over time and were continuously incorporated into the non-living SOM pool. The {sup 13}C-FA in the non-living SOM remained stable from day 59 whereas the contents of {sup 13}C-AA slightly increased until the end. After 90 days, nearly all NER were biogenic as they were made up almost completely by natural biomass compounds. The presented data demonstrated that the potential environmental risks related to the ibuprofen-derived NER are overestimated. - Highlights: ► Biogenic residue formation during microbial degradation of ibuprofen was studied. ► Nearly all non-extractable residues derived from ibuprofen were biogenic. ► Fatty acids and amino acids formed biogenic non-extractable residues and were stabilised in soil. ► Environmental risks of ibuprofen-derived non-extractable residues are overestimated.

Contribution of microorganisms to non-extractable residue formation during biodegradation of ibuprofen in soil

International Nuclear Information System (INIS)

Nowak, Karolina M.; Girardi, Cristobal; Miltner, Anja; Gehre, Matthias; Schäffer, Andreas; Kästner, Matthias

2013-01-01

Non-extractable residues (NER) formed during biodegradation of organic contaminants in soil are considered to be mainly composed of parent compounds or their primary metabolites with hazardous potential. However, in the case of biodegradable organic compounds, the soil NER may also contain microbial biomass components, for example fatty acids (FA) and amino acids (AA). After cell death, these biomolecules are subsequently incorporated into non-living soil organic matter (SOM) and are stabilised ultimately forming hardly extractable residues of biogenic origin. We investigated biodegradation of 13 C 6 -ibuprofen, in particular the metabolic incorporation of the 13 C-label into FA and AA and their fate in soil over 90 days. 13 C-FA and 13 C-AA amounts in the living microbial biomass fraction initially increased, then decreased over time and were continuously incorporated into the non-living SOM pool. The 13 C-FA in the non-living SOM remained stable from day 59 whereas the contents of 13 C-AA slightly increased until the end. After 90 days, nearly all NER were biogenic as they were made up almost completely by natural biomass compounds. The presented data demonstrated that the potential environmental risks related to the ibuprofen-derived NER are overestimated. - Highlights: ► Biogenic residue formation during microbial degradation of ibuprofen was studied. ► Nearly all non-extractable residues derived from ibuprofen were biogenic. ► Fatty acids and amino acids formed biogenic non-extractable residues and were stabilised in soil. ► Environmental risks of ibuprofen-derived non-extractable residues are overestimated

Effect of preemptive weld overlay sequence on residual stress distribution for dissimilar metal weld of Kori nuclear power plant pressurizer

Energy Technology Data Exchange (ETDEWEB)

Bae, Hong Yeol; Song, Tae Kwang; Chun, Yun Bae; Oh, Chang Young; Kim, Yun Jae [Korea Univ., Seoul (Korea, Republic of); Lee, Kyoung Soo; Park, Chi Yong [Korea Electric Power Research Institute, Daejeon (Korea, Republic of)

2008-07-01

Weld overlay is one of the residual stress mitigation method which arrest crack. An overlay weld sued in this manner is termed a Preemptive Weld OverLay(PWOL). PWOL was good for distribution of residual stress of Dissimilar Metal Weld(DMW) by previous research. Because range of overlay welding is wide relatively, residual stress distribution on PWR is affected by welding sequence. In order to examine the effect of welding sequence, PWOL was applied to a specific DMW of KORI nuclear power plant by finite element analysis method. As a result, the welding direction that from nozzle to pipe is better good for residual stress distribution on PWR.

Effect of preemptive weld overlay sequence on residual stress distribution for dissimilar metal weld of Kori nuclear power plant pressurizer

International Nuclear Information System (INIS)

Bae, Hong Yeol; Song, Tae Kwang; Chun, Yun Bae; Oh, Chang Young; Kim, Yun Jae; Lee, Kyoung Soo; Park, Chi Yong

2008-01-01

Weld overlay is one of the residual stress mitigation method which arrest crack. An overlay weld sued in this manner is termed a Preemptive Weld OverLay(PWOL). PWOL was good for distribution of residual stress of Dissimilar Metal Weld(DMW) by previous research. Because range of overlay welding is wide relatively, residual stress distribution on PWR is affected by welding sequence. In order to examine the effect of welding sequence, PWOL was applied to a specific DMW of KORI nuclear power plant by finite element analysis method. As a result, the welding direction that from nozzle to pipe is better good for residual stress distribution on PWR

Thermodynamic Effects of Replacements of Pro Residues in Helix Interiors of Maltose-Binding Protein

OpenAIRE

Prajapati, RS; Lingaraju, GM; Bacchawat, Kiran; Surolia, Avadhesha; Varadarajan, Raghavan

2003-01-01

Introduction of Pro residues into helix interiors results in protein destabilization. It is currently unclear if the converse substitution (i.e., replacement of Pro residues that naturally occur in helix interiors would be stabilizing). Maltose-binding protein is a large 370-amino acid protein that contains 21 Pro residues. Of these, three nonconserved residues (P48, P133, and P159) occur at helix interiors. Each of the residues was replaced with Ala and Ser. Stabilities were characterized by...

Effects of location, thermal stress and residual stress on corner cracks in nozzles with cladding

International Nuclear Information System (INIS)

McLean, J.L.; Cohen, L.M.; Besuner, P.M.

1979-01-01

The stress intensity factors (K 1 ) for corner cracks in a boiling water reactor feedwater nozzle with stainless steel cladding are obtained for loading by internal pressure and a fluid quench in the nozzle. Conditions both with and without residual stress in the component are considered. The residual stress is simulated by means of a reference temperature change. The stress distribution for the uncracked structure is obtained from a three-dimensional finite element model. A three-dimensional influence function (IF) method, in conjunction with the boundary-integral equation method for structural analysis, is employed to compute K 1 values from the uncracked stress distribution. For each type of loading K 1 values are given for cracks at 15 nozzle locations and for 6 crack depths. Reasonable agreement is noted between calculated and previously published pressure-induced K 1 values. Comparisons are made to determine the effect on K 1 of crack location, thermal stress and residual stress, as compared with pressure stress. For the thermal transient it is shown that K 1 for small crack depths is maximised early in the transient, while K 1 for large cracks is maximised later under steady state conditions. Computation should, therefore, be made for several transient time points and the maximum K 1 for a given crack depth should be used for design analysis. It is concluded that the effects on K 1 of location, thermal stresses and residual stresses are significant and generally too complex to evaluate without advanced numerical procedures. The utilised combination of finite element analysis of the uncracked structure and three-dimensional influence function analysis of the cracked structure is demonstrated and endorsed. (author)

Characteristics of residues from thermally treated anaerobic sludges

International Nuclear Information System (INIS)

Friedman, A.A.; Smith, J.E.; De Santis, J.; Ptak, T.; Ganley, R.C.

1988-01-01

Sludge management and disposal are probably the most difficult and expensive operations involved in wastewater treatment today. To minimize final disposal costs many waste treatment facilities practice some form of anaerobic digestion and dewatering to reduce the volume and offensiveness of their by-product sludges. One potential alternative for reducing sludge volumes consists of high temperature, partial oxidation of these previously digested sludges (PDS) and subsequent anaerobic biological conversion of resulting soluble organics to methane. This paper describes solids destruction, residue characteristics and biodegradability factors that should be considered in the design of liquid thermal treatment processes for the management of anaerobic sludges. To date only very limited information is available concerning the suitability of thermally treated PDS to serve as a substrate for the generation of methane. The primary objective of this research was to determine the feasibility of producing methane efficiently from the residual VSS in anaerobically digested sludges. Secondary goals were to establish the ''best'' conditions for thermal treatment for solubilizing PDS, to observe the effect of the soluble products on methanogenesis and to evaluate process sidestreams for dewaterability and anaerobic biodegradability

The potential for energy production from crop residues in Zimbabwe

Energy Technology Data Exchange (ETDEWEB)

Jingura, R.M.; Matengaifa, R. [School of Engineering Sciences and Technology, Chinhoyi University of Technology, P. Bag 7724, Chinhoyi (Zimbabwe)

2008-12-15

There is increasing interest in Zimbabwe in the use of renewable energy sources as a means of meeting the country's energy requirements. Biomass provides 47% of the gross energy consumption in Zimbabwe. Energy can be derived from various forms of biomass using various available conversion technologies. Crop residues constitute a large part of the biomass available from the country's agriculture-based economy. The potential for energy production of crop residues is examined using data such as estimates of the quantities of the residues and their energy content. The major crops considered are maize, sugarcane, cotton, soyabeans, groundnuts, wheat, sorghum, fruits and forestry plantations. Quantities of residues are estimated from crop yields by using conversion coefficients for the various crops. Long-term crop yields data from 1970 to 1999 were used. Total annual residue yields for crops, fruits and forestry plantations are 7.805 Mt, 378 kt and 3.05 Mt, respectively. The crops, fruits and forestry residues have energy potential of 81.5, 4.9 and 44.3 PJ per year, respectively. This represents about 44% of the gross energy consumption in Zimbabwe. The need to balance use of crop residues for both energy purposes and other purposes such as animal feeding and soil fertility improvement is also highlighted. (author)

Effectiveness of the GAEC cross-compliance standard management of stubble and crop residues in the maintenance of adequate contents of soil organic carbon

Directory of Open Access Journals (Sweden)

Domenico Ventrella

2011-08-01

Full Text Available Several studies carried out on the effects of stubble and crop residue incorporation have shown positive effects on chemical-physical soil characteristics. However, not all studies agree on the extent of soil organic matter increase which derives from this process, as this effect is strongly affected by other factors: the pedo-climatic features of the area in which the study is carried out, the type of crop residue incorporation and the agronomical management adopted to improve the decomposition of the incorporated fresh organic material. The burning of stubble and straw is common in the areas where cereals are traditionally grown. The adoption of this method is based on different technical and work-related factors, which become less important when taking into account the impact on the local environment and soil. A research is currently carried out at the CRA-SCA experimental farm in Foggia (Southern Italy on the effects of either residues incorporation or burning on the chemical-physical characteristics of the soil and on the wheat yield performance since 1977. This experiment allows for a comparison among the effects of burning, the simple incorporation of stubble and crop residues and incorporation carried out with some agronomical techniques (such as the distribution of increasing amounts of nitrogen on crop residue before incorporation and the simulation of rain (50 mm on the decomposition of organic material. The objective of the study was to understand the effect of the different residues management practices on soil chemical properties after 32 years of experimentation. The simple incorporation of straw and stubble showed a slight increase in organic soil matter of 0.7% with respect to burning. The best results for soil organic carbon and soil quality were obtained when residual incorporation included a treatment with additional mineral nitrogen.

Effect of corn residue harvest method with ruminally undegradable protein supplementation on performance of growing calves and fiber digestibility.

Science.gov (United States)

King, T M; Bondurant, R G; Jolly-Breithaupt, M L; Gramkow, J L; Klopfenstein, T J; MacDonald, J C

2017-12-01

Two experiments evaluated the effects of corn residue harvest method on animal performance and diet digestibility. Experiment 1 was designed as a 2 × 2 + 1 factorial arrangement of treatments using 60 individually fed crossbred steers (280 kg [SD 32] initial BW; = 12). Factors were the corn residue harvest method (high-stem and conventional) and supplemental RUP at 2 concentrations (0 and 3.3% diet DM). A third harvest method (low-stem) was also evaluated, but only in diets containing supplemental RUP at 3.3% diet DM because of limitations in the amount of available low-stem residue. Therefore, the 3 harvest methods were compared only in diets containing supplemental RUP. In Exp. 2, 9 crossbred wethers were blocked by BW (42.4 kg [SD 7] initial BW) and randomly assigned to diets containing corn residue harvested 1 of 3 ways (low-stem, high-stem, and conventional). In Exp. 1, steers fed the low-stem residue diet had greater ADG compared with the steers fed conventionally harvested corn residue ( = 0.03; 0.78 vs. 0.63 kg), whereas steers fed high-stem residue were intermediate ( > 0.17; 0.69 kg), not differing from either conventional or low-stem residues. Results from in vitro OM digestibility suggest that low-stem residue had the greatest ( RUP content (40% of CP) and RUP digestibility (60%) among the 3 residues ( ≥ 0.35). No interactions were observed between harvest method and the addition of RUP ( ≥ 0.12). The addition of RUP tended to result in improved ADG (0.66 ± 0.07 vs. 0.58 ± 0.07 for supplemental RUP and no RUP, respectively; = 0.08) and G:F (0.116 ± 0.006 vs. 0.095 ± 0.020 for supplemental RUP and no RUP, respectively; = 0.02) compared with similar diets without the additional RUP. In Exp. 2, low-stem residue had greater DM and OM digestibility and DE ( < 0.01) than high-stem and conventional residues, which did not differ ( ≥ 0.63). Low-stem residue also had the greatest NDF digestibility (NDFD; < 0.01), whereas high-stem residue had greater

Crystallization behavior of nuclear waste forms

International Nuclear Information System (INIS)

Rusin, J.M.; Lokken, R.O.; May, R.P.; Wald, J.W.

1981-09-01

Several waste form options have been or are being developed for the immobilization of high-level wastes. The final selection of a waste form must take into consideration both waste form product as well as process factors. Crystallization behavior has an important role in nuclear waste form technology. For glass or vitreous waste forms, crystallization is generally controlled to a minimum by appropriate glass formulation and heat treatment schedules. With glass ceramic waste forms, crystallization is essential to convert glass products to highly crystalline waste forms with a minimum residual glass content. In the case of ceramic waste forms, additives and controlled sintering schedules are used to contain the radionuclides in specific tailored crystalline phases

Investigation on the effects of geometric variables on the residual stresses and PWSCC growth in the RPV BMI penetration nozzles

International Nuclear Information System (INIS)

Kim, Jong Sung; Ra, Myoung Soo; Lee, Kyoung Soo

2015-01-01

This study investigated the effects of various geometric variables on the residual stresses and PWSCC growth of RPV BMI penetration nozzles. An FE residual stress analysis procedure was developed and validated from the viewpoint of FFS assessment. The validated FE residual stress analysis procedure and the PWSCC growth assessment procedure in the ASME B and PV Code, Sec.XI were applied to the BMI penetration nozzles with specified ranges of the geometric variables. The total stresses at steady state during normal operation including welding residual stresses increase with increasing inclination angle of the BMI nozzles, and with tilt angle, depth, and root width of the J-groove weld. The lifetime from the assumed initial crack to the acceptance criteria according to the ASME B and PV Code, Sec.XI also decreases under these conditions. The total stresses decrease and the lifetime increases with increasing nozzle thickness, but outer radius of the BMI nozzles has an insignificant effect on both of these factors.

The residual zonal dynamics in a toroidally rotating tokamak

International Nuclear Information System (INIS)

Zhou Deng

2015-01-01

Zonal flows, initially driven by ion-temperature-gradient turbulence, may evolve due to the neoclassic polarization in a collisionless tokamak plasma. In this presentation, the form of the residual zonal flow is presented for tokamak plasmas rotating toroidally at arbitrary velocity. The gyro-kinetic equation is analytically solved to give the expression of residual zonal flows with arbitrary rotating velocity. The zonal flow level decreases as the rotating velocity increases. The numerical evaluation is in good agreement with the previous simulation result for high aspect ratio tokamaks. (author)

Cytotoxic effects of oxytetracycline residues in the bones of broiler chickens following therapeutic oral administration of a water formulation.

Science.gov (United States)

Odore, R; De Marco, M; Gasco, L; Rotolo, L; Meucci, V; Palatucci, A T; Rubino, V; Ruggiero, G; Canello, S; Guidetti, G; Centenaro, S; Quarantelli, A; Terrazzano, G; Schiavone, A

2015-08-01

Tetracyclines, which represent one of the most commonly used antibiotics for poultry, are known to be deposited in bones, where they can remain, despite the observation of appropriate withdrawal times. The aim of the study was to determine the concentration of oxytretracycline (OTC) residues in the bone and muscle of chickens, following the oral administration of a commercially available liquid formulation, and to test their cytotoxic effects on an in vitro cell culture model. Seventy-two 1-day-old broiler chickens were randomly allotted into 2 groups (control and treated animals). OTC (40 mg/kg BW) was administered via drinking water during the 1 to 5 and 20 to 25 days of life periods. At the end of the trial, the birds were slaughtered and the OTC residues in the target tissues were measured by means of liquid chromatography (LC) - tandem mass spectrometry (MS/MS). Cytotoxicity was assessed by evaluating the pro-apoptotic effect of the bone residues on the K562 erythroleukemic line and on the peripheral blood mononuclear cells (PBMC). In all the animals, the OTC residues in the muscle were far below the established MRL of 100 μg/kg. The OTC levels in the bones of the treated animals were instead found in the parts per million (ppm) range. Cell cytotoxicity was assessed by evaluating the pro-apoptotic effect of OTC bone residues on the haematopoietic cell system. This in vitro system has revealed a significant pro-apoptotic effect on both the K562 cell line and PBMC cultures. This result suggests potential human and animal health risks due to the entry of tetracycline residues contained in the bones of treated livestock into the food-chain. This could be of concern, particularly for canine and feline diets, as meat, bone meal, and poultry by-products represent some of the main ingredients of pet foods, especially in the case of dry pet food. Further studies are needed to define the underlying mechanisms of cytotoxicity and to evaluate the in vivo toxicological

Residual antibiofilm effects of various concentrations of double antibiotic paste used during regenerative endodontics after different application times.

Science.gov (United States)

Jenks, Daniel B; Ehrlich, Ygal; Spolnik, Kenneth; Gregory, Richard L; Yassen, Ghaeth H

2016-10-01

We investigated the residual antibiofilm effects of different concentrations of double antibiotic paste (DAP) applied on radicular dentin for 1 or 4 weeks. Dentin samples were prepared (n=120), sterilized and pretreated for 1 or 4 weeks with the clinically used concentration of DAP (500mg/mL), low concentrations of DAP (1, 5 or 50mg/mL) loaded into a methylcellulose system, calcium hydroxide (Ca(OH) 2 ), or placebo paste. After the assigned treatment time, treatment pastes were rinsed off and the samples were kept independently in phosphate buffered saline for 3 weeks. Pretreated dentin samples were then inoculated with Enterococcus faecalis and bacterial biofilms were allowed to grow for an additional 3 weeks. Biofilms were then retrieved from dentin using biofilm disruption assays, diluted, spiral plated, and quantified. Fisher's Exact and Wilcoxon rank sum tests were used for statistical comparisons (α=0.05). Dentin pretreatment for 4 weeks with 5, 50 or 500mg/mL of DAP demonstrated significantly higher residual antibiofilm effects and complete eradication of E. faecalis biofilms in comparison to a 1 week pretreatment with similar concentrations. However, dentin pretreated with 1mg/mL of DAP or Ca(OH) 2 did not provide a substantial residual antibiofilm effect regardless of the application time. Dentin pretreatment with 5mg/mL of DAP or higher for 4 weeks induced significantly higher residual antibiofilm effects in comparison to a 1 week pretreatment with the same concentrations. Copyright © 2016 Elsevier Ltd. All rights reserved.

Ensemble Kalman filtering with residual nudging

Directory of Open Access Journals (Sweden)

Xiaodong Luo

2012-10-01

Full Text Available Covariance inflation and localisation are two important techniques that are used to improve the performance of the ensemble Kalman filter (EnKF by (in effect adjusting the sample covariances of the estimates in the state space. In this work, an additional auxiliary technique, called residual nudging, is proposed to monitor and, if necessary, adjust the residual norms of state estimates in the observation space. In an EnKF with residual nudging, if the residual norm of an analysis is larger than a pre-specified value, then the analysis is replaced by a new one whose residual norm is no larger than a pre-specified value. Otherwise, the analysis is considered as a reasonable estimate and no change is made. A rule for choosing the pre-specified value is suggested. Based on this rule, the corresponding new state estimates are explicitly derived in case of linear observations. Numerical experiments in the 40-dimensional Lorenz 96 model show that introducing residual nudging to an EnKF may improve its accuracy and/or enhance its stability against filter divergence, especially in the small ensemble scenario.

Disposing of coal combustion residues in inactive surface mines: Effects on water quality

International Nuclear Information System (INIS)

Kim, A.G.; Ackman, T.E.

1994-01-01

The disposal of coal combustion residues (CCR) in surface and underground coal mines can provide a stable, low-maintenance alternative to landfills, benefiting the mining and electric power industries. The material may be able to improve water quality at acid generating abandoned or reclaimed coal mine sites. Most combustion residues are alkaline, and their addition to the subsurface environment could raise the pH, limiting the propagation of pyrite oxidizing bacteria and reducing the rate of acid generation. Many of these CCR are also pozzolanic, capable of forming cementitious grouts. Grouts injected into the buried spoil may decrease its permeability and porosity, diverting water away from the pyritic material. Both mechanisms, alkaline addition and water diversion, are capable of reducing the amount of acid produced at the disposal site. The US Bureau of Mines is cooperating in a test of subsurface injection of CCR into a reclaimed surface mine. Initially, a mixture of fly ash, lime, and acid mine drainage (AMD) sludge was injected. Lime was the source of calcium for the formation of the pozzolanic grout. Changes in water quality parameters (pH, acidity, anions, and trace metals) in water samples from wells and seeps indicate a small but significant improvement after CCR injection. Changes in the concentration of heavy metals in the water flowing across the site were apparently influenced by the presence of flyash

The effect of residual thermal stresses on the fatigue crack growth of laser-surface-annealed AISI 304 stainless steel Part I: computer simulation

International Nuclear Information System (INIS)

Shiue, R.K.; Chang, C.T.; Young, M.C.; Tsay, L.W.

2004-01-01

The effect of residual thermal stresses on the fatigue crack growth of the laser-surface-annealed AISI 304 stainless steel, especially the effect of stress redistribution ahead of the crack tip was extensively evaluated in the study. Based on the finite element simulation, the longitudinal residual tensile stress field has a width of roughly 20 mm on the laser-irradiated surface and was symmetric with respect to the centerline of the laser-annealed zone (LAZ). Meanwhile, residual compressive stresses distributed over a wide region away from the LAZ. After introducing a notch perpendicular to the LAZ, the distribution of longitudinal residual stresses became unsymmetrical about the centerline of LAZ. High residual compressive stresses exist within a narrow range ahead of notch tip. The improved crack growth resistance of the laser-annealed specimen might be attributed to those induced compressive stresses. As the notch tip passed through the centerline of the LAZ, the residual stress ahead of the notch tip was completely reverted into residual tensile stresses. The existence of unanimous residual tensile stresses ahead of the notch tip was maintained, even if the notch tip extended deeply into the LAZ. Additionally, the presence of the residual tensile stress ahead of the notch tip did not accelerate the fatigue crack growth rate in the compact tension specimen

Effects on Machining on Surface Residual Stress of SA 508 and Austenitic Stainless Steel

International Nuclear Information System (INIS)

Lee, Kyoung Soo; Lee, Seong Ho; Park, Chi Yong; Yang, Jun Seok; Lee, Jeong Geun; Park, Jai Hak

2011-01-01

Primary water stress corrosion cracking has occurred in dissimilar weld areas in nuclear power plants. Residual stress is a driving force in the crack. Residual stress may be generated by weld or surface machining. Residual stress due to surface machining depends on the machining method, e.g., milling, grinding, or EDM. The stress is usually distributed on or near the surface of the material. We present the measured residual stress for machining on SA 508 and austenitic stainless steels such as TP304 and F316. The residual stress can be tensile or compressive depending on the machining method. The depth and the magnitude of the residual stress depend on the material and the machining method

Effects of residual hearing on cochlear implant outcomes in children: A systematic-review.

Science.gov (United States)

Chiossi, Julia Santos Costa; Hyppolito, Miguel Angelo

2017-09-01

to investigate if preoperative residual hearing in prelingually deafened children can interfere on cochlear implant indication and outcomes. a systematic-review was conducted in five international databases up to November-2016, to locate articles that evaluated cochlear implantation in children with some degree of preoperative residual hearing. Outcomes were auditory, language and cognition performances after cochlear implant. The quality of the studies was assessed and classified according to the Oxford Levels of Evidence table - 2011. Risk of biases were also described. From the 30 articles reviewed, two types of questions were identified: (a) what are the benefits of cochlear implantation in children with residual hearing? (b) is the preoperative residual hearing a predictor of cochlear implant outcome? Studies ranged from 04 to 188 subjects, evaluating populations between 1.8 and 10.3 years old. The definition of residual hearing varied between studies. The majority of articles (n = 22) evaluated speech perception as the outcome and 14 also assessed language and speech production. There is evidence that cochlear implant is beneficial to children with residual hearing. Preoperative residual hearing seems to be valuable to predict speech perception outcomes after cochlear implantation, even though the mechanism of how it happens is not clear. More extensive researches must be conducted in order to make recommendations and to set prognosis for cochlear implants based on children preoperative residual hearing. Copyright © 2017 Elsevier B.V. All rights reserved.

Experimental study on effect of roasting, boiling and microwave cooking methods on enrofloxacin antibiotic residues in edible poultry tissues

Directory of Open Access Journals (Sweden)

A Javadi

2011-11-01

Full Text Available The purpose of this study was to determine the effects of different cooking processes such as boiling, roasting and microwaving on enrofloxacin residues in muscle, liver and gizzard tissues of broiler chickens. Each of chicks was fed by routine diet and water with %0.05 of enrofloxacine for consecutive 5 days .Then; three locations including breast muscle, liver and gizzard were sampled aseptically from each carcass. Enrofloxacin residue was analyzed using microbial method by plates seeded with Escherichia coli. After doing different phases of the test on raw samples, the positive raw samples cooked by various cooking procedures and we surveyed cooked samples with similar method again for present of residue. The results were show reduction in concentration of enrofloxacin residue after different cooking processes. The most reduction of the residue in cooked meat and gizzard samples related to boiling process and roasting process for cooked liver samples and the highest detectable amount of residue belonged to microwaving process in all cooked samples. Regarding to the results of this study, we can conclude that cooking processes can’t annihilate total amounts of these drug and it can only decrease their amounts and the most of residue in boiling process excreted from tissue to cooking fluid.

Combined effect of electric field and residual stress on propagation of indentation cracks in a PZT-5H ferroelectric ceramic

International Nuclear Information System (INIS)

Huang, H.Y.; Chu, W.Y.; Su, Y.J.; Qiao, L.J.; Gao, K.W.

2005-01-01

The combined effect of electric field and residual stress on propagation of unloaded indentation cracks in a PZT-5 ceramic has been studied. The results show that residual stress itself is too small to induce delayed propagation of the indentation cracks in silicon oil. If applied constant electric field is larger than 0.2 kV/cm, the combined effect of electric field and residual stress can cause delayed propagation of the indentation crack after passing an incubation time in silicon oil, but the crack will arrest after propagating for 10-30 μm because of decrease of the resultant stress intensity factor induced by the field and residual stress with increasing the crack length. The threshold electric field for delayed propagation of the indentation crack in silicon oil is E DP = 0.2 kV/cm. If the applied electric field is larger than 5.25 kV/cm, combined effect of the electric field and residual stress can cause instant propagation of the indentation crack, and under sustained electric field, the crack which has propagated instantly can propagate continuously, until arrest at last. The critical electric field for instant propagation of the indentation crack is E P = 5.25 kV/cm. If the applied electric field is larger than 12.6 kV/cm, the microcracks induced by the electric field initiate everywhere, grow and connect in a smooth specimen, resulting in delayed failure, even without residual stress. The threshold electric field for delayed failure of a smooth specimen in silicon oil is E DF = 12.6 kV/cm and the critical electric field for instant failure is E F = 19.1 kV/cm

Amelioration of bauxite residue sand by intermittent additions of nitrogen fertiliser and leaching fractions: The effect on growth of kikuyu grass and fate of applied nutrients.

Science.gov (United States)

Kaur, Navjot; Phillips, Ian; Fey, Martin V

2016-04-15

Bauxite residue, a waste product of aluminium processing operations is characterised by high pH, salinity and exchangeable sodium which hinders sustainable plant growth. The aim of this study was to investigate the uptake form, optimum application rate and timing of nitrogen fertiliser to improve bauxite residue characteristics for plant growth. Kikuyu grass was grown in plastic columns filled with residue sand/carbonated residue mud mixture (20:1) previously amended with gypsum, phosphoric acid and basal nutrients. The experiment was set up as a 4×4 factorial design comprising four levels of applied nitrogen (N) fertiliser (0, 3, 6 and 12mgNkg(-1) residue) and four frequencies of leaching (16, 8 and 4day intervals). We hypothesised that the use of ammonium sulfate fertiliser would increase retention of N within the rhizosphere thereby encouraging more efficient fertiliser use. We found that N uptake by kikuyu grass was enhanced due to leaching of excess salts and alkalinity from the residue profile. It was also concluded that biomass production and associated N uptake by kikuyu grass grown in residue is dependent on the type of fertiliser used. Copyright © 2016 Elsevier B.V. All rights reserved.

Selective effects of charge on G protein activation by FSH-receptor residues 551-555 and 650-653.

Science.gov (United States)

Grasso, P; Deziel, M R; Reichert, L E

1995-01-01

Two cytosolic regions of the rat testicular FSH receptor (FSHR), residues 533-555 and 645-653, have been identified as G protein-coupling domains. We localized the activity in these domains to their C-terminal sequences, residues 551-555 (KIAKR, net charge +3) and 650-653 (RKSH, net charge +3), and examined the effects of charge on G protein activation by the C-terminal peptides, using synthetic analogs containing additions, through alanine (A) linkages, of arginine (R, +), histidine (H, +) or both. RA-KIAKR (net charge +4) mimicked the effect of FSHR-(551-555) on guanine nucleotide exchange in rat testis membranes, but reduced its ability to inhibit FSH-stimulated estradiol biosynthesis in cultured rat Sertoli cells. Further increasing net charge by the addition of H (HARA-KIAKR, net charge +5) increased guanosine 5'-triphosphate (GTP) binding, but eliminated FSHR-(551-555) effects on FSH-stimulated steroidogenesis. HA-RKSH (net charge +4) significantly inhibited guanine nucleotide exchange in rat testis membranes, but stimulated basal and potentiated FSH-induced estradiol biosynthesis in cultured rat Sertoli cells. Addition of two H residues (HAHA-RKSH, net charge +5) restored GTP binding and further potentiated basal and FSH-stimulated steroidogenesis. These results suggest that positive charges in G protein-coupling domains of the FSHR play a role in modulating G protein activation and postbinding effects of FSH, such as steroidogenesis.

Modeling the residual effects and threshold saturation of training: a case study of Olympic swimmers.

Science.gov (United States)

Hellard, Philippe; Avalos, Marta; Millet, Gregoire; Lacoste, Lucien; Barale, Frederic; Chatard, Jean-Claude

2005-02-01

The aim of this study was to model the residual effects of training on the swimming performance and to compare a model that includes threshold saturation (MM) with the Banister model (BM). Seven Olympic swimmers were studied over a period of 4 +/- 2 years. For 3 training loads (low-intensity w(LIT), high-intensity w(HIT), and strength training w(ST)), 3 residual training effects were determined: short-term (STE) during the taper phase (i.e., 3 weeks before the performance [weeks 0, 1, and 2]), intermediate-term (ITE) during the intensity phase (weeks 3, 4, and 5), and long-term (LTE) during the volume phase (weeks 6, 7, and 8). ITE and LTE were positive for w(HIT) and w(LIT), respectively (p measures indicated that MM compares favorably with BM. Identifying individual training thresholds may help individualize the distribution of training loads.

Residual stress in spin-cast polyurethane thin films

Energy Technology Data Exchange (ETDEWEB)

Zhang, Hong; Zhang, Li, E-mail: lizhang@mae.cuhk.edu.hk [Department of Mechanical and Automation Engineering, The Chinese University of Hong Kong, Shatin N.T., Hong Kong (China); Chow Yuk Ho Technology Centre for Innovative Medicine, The Chinese University of Hong Kong, Shatin N.T., Hong Kong (China)

2015-01-19

Residual stress is inevitable during spin-casting. Herein, we report a straightforward method to evaluate the residual stress in as-cast polyurethane thin films using area shrinkage measurement of films in floating state, which shows that the residual stress is independent of radial location on the substrate and decreased with decreasing film thickness below a critical value. We demonstrate that the residual stress is developed due to the solvent evaporation after vitrification during spin-casting and the polymer chains in thin films may undergo vitrification at an increased concentration. The buildup of residual stress in spin-cast polymer films provides an insight into the size effects on the nature of polymer thin films.

Residual stress studies of austenitic and ferritic steels

International Nuclear Information System (INIS)

Chrenko, R.M.

1978-01-01

Residual studies have been made on austenitic and ferritic steels of the types used as structural materials. The residual stress results presented here will include residual stress measurements in the heat-affected zone on butt welded Type 304 stainless steel pipes, and the stresses induced in Type 304 austenitic stainless steel and Type A508 ferritic steel by several surface preparations. Such surface preparation procedures as machining and grinding can induce large directionality effects in the residual stresses determined by X-ray techniques and some typical data will be presented. A brief description is given of the mobile X-ray residual stress apparatus used to obtain most of the data in these studies. (author)

Effect of processing conditions and methods on residual stress in CeO2 buffer layers and YBCO superconducting films

International Nuclear Information System (INIS)

Xiong Jie; Qin Wenfeng; Cui Xumei; Tao Bowan; Tang Jinlong; Li Yanrong

2006-01-01

CeO 2 layers have been fabricated by pulsed laser deposition (PLD) technique on (1 1 0 2) sapphire substrate. Microstructure of CeO 2 layers is characterized by X-ray diffraction as functions of substrate temperature. The effects of the substrate temperature on the residual stress have been studied. The results show that residual stress in CeO 2 film decreased with increasing substrate temperature, not the same development tendency as that of thermal stress. This means that the thermal stress is only a fraction of the residual stress. Moreover, YBCO superconducting films were prepared by direct current (DC) sputtering and pulsed laser deposition (PLD) technique. The residual stress and thermal stress of both YBCO films were measured. PLD processing apparently generated higher intrinsic compressive stresses in comparison to DC sputtering

Glycoform-Selective Prion Formation in Sporadic and Familial Forms of Prion Disease

Science.gov (United States)

Xiao, Xiangzhu; Yuan, Jue; Haïk, Stéphane; Cali, Ignazio; Zhan, Yian; Moudjou, Mohammed; Li, Baiya; Laplanche, Jean-Louis; Laude, Hubert; Langeveld, Jan; Gambetti, Pierluigi; Kitamoto, Tetsuyuki; Kong, Qingzhong; Brandel, Jean-Philippe; Cobb, Brian A.; Petersen, Robert B.; Zou, Wen-Quan

2013-01-01

The four glycoforms of the cellular prion protein (PrPC) variably glycosylated at the two N-linked glycosylation sites are converted into their pathological forms (PrPSc) in most cases of sporadic prion diseases. However, a prominent molecular characteristic of PrPSc in the recently identified variably protease-sensitive prionopathy (VPSPr) is the absence of a diglycosylated form, also notable in familial Creutzfeldt-Jakob disease (fCJD), which is linked to mutations in PrP either from Val to Ile at residue 180 (fCJDV180I) or from Thr to Ala at residue 183 (fCJDT183A). Here we report that fCJDV180I, but not fCJDT183A, exhibits a proteinase K (PK)-resistant PrP (PrPres) that is markedly similar to that observed in VPSPr, which exhibits a five-step ladder-like electrophoretic profile, a molecular hallmark of VPSPr. Remarkably, the absence of the diglycosylated PrPres species in both fCJDV180I and VPSPr is likewise attributable to the absence of PrPres glycosylated at the first N-linked glycosylation site at residue 181, as in fCJDT183A. In contrast to fCJDT183A, both VPSPr and fCJDV180I exhibit glycosylation at residue 181 on di- and monoglycosylated (mono181) PrP prior to PK-treatment. Furthermore, PrPV180I with a typical glycoform profile from cultured cells generates detectable PrPres that also contains the diglycosylated PrP in addition to mono- and unglycosylated forms upon PK-treatment. Taken together, our current in vivo and in vitro studies indicate that sporadic VPSPr and familial CJDV180I share a unique glycoform-selective prion formation pathway in which the conversion of diglycosylated and mono181 PrPC to PrPSc is inhibited, probably by a dominant-negative effect, or by other co-factors. PMID:23527023

Surgical treatment for residual or recurrent strabismus

Directory of Open Access Journals (Sweden)

Tao Wang

2014-12-01

Full Text Available Although the surgical treatment is a relatively effective and predictable method for correcting residual or recurrent strabismus, such as posterior fixation sutures, medial rectus marginal myotomy, unilateral or bilateral rectus re-recession and resection, unilateral lateral rectus recession and adjustable suture, no standard protocol is established for the surgical style. Different surgical approaches have been recommended for correcting residual or recurrent strabismus. The choice of the surgical procedure depends on the former operation pattern and the surgical dosages applied on the patients, residual or recurrent angle of deviation and the operator''s preference and experience. This review attempts to outline recent publications and current opinion in the management of residual or recurrent esotropia and exotropia.

Release time of residual oxygen after dental bleaching with 35% hydrogen peroxide: effect of a catalase-based neutralizing agent.

Science.gov (United States)

Guasso, Bárbara; Salomone, Paloma; Nascimento, Paulo Cícero; Pozzobon, Roselaine Terezinha

2016-01-01

This article assessed the effect of a catalase-based agent on residual oxygen (O2) release from teeth exposed to 35% hydrogen peroxide (H2O2). The use of the catalase-based neutralizer agent for 2-3 minutes was able to release residual O2 5 days after exposure to a 35% H2O2-based bleaching gel.

Compared cycling in a soil-plant system of pea and barley residue nitrogen

DEFF Research Database (Denmark)

Jensen, E.S.

1996-01-01

Field experiments were carried out on a temperate soil to determine the decline rate, the stabilization in soil organic matter and the plant uptake of N from N-15-labelled crop residues. The fate of N from field pea (Pisum sativum L.) and spring barley (Hordeum vulgare L.) residues was followed...... mineralization of N was highly correlated to the concentrations of soluble C and N and the lignin:N ratio of residues. The contribution of residue-derived N to the inorganic N pool was at its maximum 30 DAI (10-55%) and declined to on average 5% after 3 years of decomposition. Residual organic labelled N...... in the top 10 cm soil declined rapidly during the initial 86 DAI for all residue types. Leaching of soluble organic materials may have contributed to this decline. At 216 DAI 72, 59 and 45% of the barley, mature pea and green pea residue N, respectively, were present in organic N-forms in the topsoil. During...

Crop residue decomposition in Minnesota biochar amended plots

OpenAIRE

S. L. Weyers; K. A. Spokas

2014-01-01

Impacts of biochar application at laboratory scales are routinely studied, but impacts of biochar application on decomposition of crop residues at field scales have not been widely addressed. The priming or hindrance of crop residue decomposition could have a cascading impact on soil processes, particularly those influencing nutrient availability. Our objectives were to evaluate biochar effects on field decomposition of crop residue, using plots that were amended with ...

Chemical modification of lysine residues in lysozyme may dramatically influence its amyloid fibrillation.

Science.gov (United States)

Morshedi, Dina; Ebrahim-Habibi, Azadeh; Moosavi-Movahedi, Ali Akbar; Nemat-Gorgani, Mohsen

2010-04-01

Studies on the aggregation of mutant proteins have provided new insights into the genetics of amyloid diseases and the role of the net charge of the protein on the rate, extent, and type of aggregate formation. In the present work, hen egg white lysozyme (HEWL) was employed as the model protein. Acetylation and (separately) citraconylation were employed to neutralize the charge on lysine residues. Acetylation of the lysine residues promoted amyloid formation, resulting in more pronounced fibrils and a dramatic decline in the nucleation time. In contrast, citraconylation produced the opposite effect. In both cases, native secondary and tertiary structures appeared to be retained. Studies on the effect of pH on aggregation suggested greater possibilities for amorphous aggregate formation rather than fibrillation at pH values closer to neutrality, in which the protein is known to take up a conformation more similar to its native form. This is in accord with reports in the literature suggesting that formation of amorphous aggregates is more favored under relatively more native conditions. pH 5 provided a critical environment in which a mixture of amorphous and fibrillar structures were observed. Use of Tango and Aggrescan software which describe aggregation tendencies of different parts of a protein structure suggested critical importance of some of the lysine residues in the aggregation process. Results are discussed in terms of the importance of the net charge in control of protein-protein interactions leading to aggregate formation and possible specific roles of lysine residues 96 and 97. Copyright 2009 Elsevier B.V. All rights reserved.

Effect of Young's modulus evolution on residual stress measurement of thermal barrier coatings by X-ray diffraction

International Nuclear Information System (INIS)

Chen, Q.; Mao, W.G.; Zhou, Y.C.; Lu, C.

2010-01-01

Subjected to thermal cycling, the apparent Young's modulus of air plasma-sprayed (APS) 8 wt.% Y 2 O 3 -stabilized ZrO 2 (8YSZ) thermal barrier coatings (TBCs) was measured by nanoindentation. Owing to the effects of sintering and porous microstructure, the apparent Young's modulus follows a Weibull distribution and changes from 50 to 93 GPa with an increase of thermal cycling. The evolution of residual stresses in the top coating of an 8YSZ TBC system was determined by X-ray diffraction (XRD). The residual stresses derived from the XRD data are well consistent with that obtained by the Vickers indention. It is shown that the evolution of Young's modulus plays an important role in improving the measurement precision of residual stresses in TBCs by XRD.

Evolution of titanium residue on the walls of a plasma-etching reactor and its effect on the polysilicon etching rate

Energy Technology Data Exchange (ETDEWEB)

Hirota, Kosa, E-mail: hirota-kousa@sme.hitachi-hitec.com; Itabashi, Naoshi; Tanaka, Junichi [Hitachi, Ltd., Central Research Laboratory, 1-280, Higashi-Koigakubo, Kokubunji, Tokyo 185-8601 (Japan)

2014-11-01

The variation in polysilicon plasma etching rates caused by Ti residue on the reactor walls was investigated. The amount of Ti residue was measured using attenuated total reflection Fourier transform infrared spectroscopy with the HgCdTe (MCT) detector installed on the side of the reactor. As the amount of Ti residue increased, the number of fluorine radicals and the polysilicon etching rate increased. However, a maximum limit in the etching rate was observed. A mechanism of rate variation was proposed, whereby F radical consumption on the quartz reactor wall is suppressed by the Ti residue. The authors also investigated a plasma-cleaning method for the removal of Ti residue without using a BCl{sub 3} gas, because the reaction products (e.g., boron oxide) on the reactor walls frequently cause contamination of the product wafers during etching. CH-assisted chlorine cleaning, which is a combination of CHF{sub 3} and Cl{sub 2} plasma treatment, was found to effectively remove Ti residue from the reactor walls. This result shows that CH radicals play an important role in deoxidizing and/or defluorinating Ti residue on the reactor walls.

Characterization of glass and glass ceramic nuclear waste forms

International Nuclear Information System (INIS)

Lutze, W.; Borchardt, J.; De, A.K.

1979-01-01

Characteristics of solidified nuclear waste forms, glass and glass ceramic compositions and the properties (composition, thermal stability, crystallization, phase behavior, chemical stability, mechanical stability, and radiation effects) of glasses and glass ceramics are discussed. The preparation of glass ceramics may be an optional step for proposed vitrification plants if tailored glasses are used. Glass ceramics exhibit some improved properties with respect to glasses. The overall leach resistance is similar to that of glasses. An increased leach resistance may become effective for single radionuclides being hosted in highly insoluble crystal phases mainly when higher melting temperatures are applicable in order to get more leach resistant residual glass phases. The development of glass ceramic is going on. The technological feasibility is still to be demonstrated. The potential gain of stability when using glass ceramics qualifies the material as an alternative nuclear waste form

Assessment of the effect of washing and boiling on the levels of pesticide residues in vegetables cultivated in Akuapem North Municipality

International Nuclear Information System (INIS)

Opare-Boafo, Maame Serwa

2016-07-01

Vegetables play an important role in human nutrition and health. Pesticides are extensively used by vegetable farmers in crop production and this may contaminate the crop. Traditional method of washing vegetables prior to consumption has been assumed to reduce pesticide residues. The study seeks to assess the effect of washing with various solutions and with boiling on the concentration of pesticide residues in vegetables and to estimate the potential human health risk associated with pesticide ingestion via vegetable diet using the Quick, Easy, Cheap, Effective, Rugged and Safe (QuEChERS) method. Results of the study indicated that the farmers involved in vegetable farming in the Akwapim North Municipality are in the middle age group and use pesticides in their farming activities. Majority (65%) of them have no formal training in pesticide usage and apply pesticides in mixtures made of combinations of up to four (4) pesticides in a single tank mixture. The farmers do not use any protective clothing and stores agrochemicals in multipurpose storage structures together with food containers and farm implements. As a result of pesticide exposure, 67% of farmers experienced various kinds of discomfort including headache, tingling or burning of skin, irritation of eyes or skin. Chloropyrifos residue was the only pesticide residue that gave positive detection in the analysed vegetable samples. The raw (non-spiked) vegetable samples (cabbage, lettuce and squash) had 0.29 mg kg -1 , 0.19 mg kg -1 and 0.14 mg kg -1 of Chloropyrifos residue in cabbage, squash and lettuce respectively. The level of chloropyrifos residues detected in raw cabbage samples from the study area was below the maximum permissible limit (MPLs) of 1 mg/kg (Codex, 2003) but the residues found in raw squash was above the maximum permissible limit of 0.01 mg/kg and that of lettuce was also above the maximum permissible limit (0.05mg/kg). Washing of vegetables vigorously in water for 2 minutes before

Evaluation and optimization of nutritional and environmental impact of biogas residues

International Nuclear Information System (INIS)

Lichti, Fabian Heribert

2013-01-01

On the basis of the dynamic growth of biogas plants in Germany the fertilization with biogas residues has obtained an important role for recirculation of plant nutrients, particularly with regard to nitrogen. In this work the effect of N nutrition with biogas residues was assessed in a 3-year on-field trial conducted at four sites throughout Bavaria. The fertilizing effects were tested by varying rate and time of biogas residues application, using different application techniques and the addition of nitrification inhibitors on several crops. The biogas residues achieved mineral fertilizer equivalents of 30 - 45 %. Overall, the untreated biogas residues showed a slightly increased N efficiency compared to cattle manure, whereas particularly site-dependent differences resulted in large differences in N efficiency of biogas residues.

Failure Modes and Effects Analysis (FMEA) of the Residual Heat Removal System

International Nuclear Information System (INIS)

Eggleston, F.T.

1976-01-01

The Residual Heat Removal System (RHRS) transfer heat from the Reactor Coolant System (RCS) to the reactor plant Component Cooling System (CCS) to reduce the temperature of the RCS at a controlled rate during the second part of normal plant cooldown and maintains the desired temperature until the plant is restarted. By the use of an analytic tool, the Failure Modes and Effects Analysis, it is shown that the RHRS, because of its redundant two train design, is able to accommodate any credible component single failure with the only effect being an extension in the required cooldown time, thus demonstrating the reliability of the RHRS to perform its intended function