Disposal of Rocky Flats residues as waste

International Nuclear Information System (INIS)

Dustin, D.F.; Sendelweck, V.S.

1993-01-01

Work is underway at the Rocky Flats Plant to evaluate alternatives for the removal of a large inventory of plutonium-contaminated residues from the plant. One alternative under consideration is to package the residues as transuranic wastes for ultimate shipment to the Waste Isolation Pilot Plant. Current waste acceptance criteria and transportation regulations require that approximately 1000 cubic yards of residues be repackaged to produce over 20,000 cubic yards of WIPP certified waste. The major regulatory drivers leading to this increase in waste volume are the fissile gram equivalent, surface radiation dose rate, and thermal power limits. In the interest of waste minimization, analyses have been conducted to determine, for each residue type, the controlling criterion leading to the volume increase, the impact of relaxing that criterion on subsequent waste volume, and the means by which rules changes may be implemented. The results of this study have identified the most appropriate changes to be proposed in regulatory requirements in order to minimize the costs of disposing of Rocky Flats residues as transuranic wastes

Waste washing pre-treatment of municipal and special waste.

Science.gov (United States)

Cossu, Raffaello; Lai, Tiziana; Pivnenko, Kostyantyn

2012-03-15

Long-term pollution potential in landfills is mainly related to the quality of leachate. Waste can be conveniently treated prior to landfilling with an aim to minimizing future emissions. Washing of waste represents a feasible pre-treatment method focused on controlling the leachable fraction of residues and relevant impact. In this study, non-recyclable plastics originating from source segregation, mechanical-biological treated municipal solid waste (MSW), bottom ash from MSW incineration and automotive shredder residues (ASR) were treated and the removal efficiency of washing pre-treatment prior to landfilling was evaluated. Column tests were performed to simulate the behaviour of waste in landfill under aerobic and anaerobic conditions. The findings obtained revealed how waste washing treatment (WWT) allowed the leachability of contaminants from waste to be reduced. Removal rates exceeding 65% were obtained for dissolved organic carbon (DOC), chemical oxygen demand (COD) and Total Kjeldahl Nitrogen (TKN). A percentage decrease of approximately 60% was reached for the leachable fraction of chlorides, sulphates, fluoride and metals, as proved by a reduction in electric conductivity values (70%). Copyright © 2011 Elsevier B.V. All rights reserved.

Treatment of air pollution control residues with iron rich waste sulfuric acid: does it work for antimony (Sb)?

Science.gov (United States)

Okkenhaug, Gudny; Breedveld, Gijs D; Kirkeng, Terje; Lægreid, Marit; Mæhlum, Trond; Mulder, Jan

2013-03-15

Antimony (Sb) in air pollution control (APC) residues from municipal solid waste incineration has gained increased focus due to strict Sb leaching limits set by the EU landfill directive. Here we study the chemical speciation and solubility of Sb at the APC treatment facility NOAH Langøya (Norway), where iron (Fe)-rich sulfuric acid (∼3.6M, 2.3% Fe(II)), a waste product from the industrial extraction of ilmenite, is used for neutralization. Antimony in water extracts of untreated APC residues occurred exclusively as pentavalent antimonate, even at low pH and Eh values. The Sb solubility increased substantially at pH<10, possibly due to the dissolution of ettringite (at alkaline pH) or calcium (Ca)-antimonate. Treated APC residues, stored anoxically in the laboratory, simulating the conditions at the NOAH Langøya landfill, gave rise to decreasing concentrations of Sb in porewater, occurring exclusively as Sb(V). Concentrations of Sb decreased from 87-918μgL(-1) (day 3) to 18-69μgL(-1) (day 600). We hypothesize that an initial sorption of Sb to Fe(II)-Fe(III) hydroxides (green rust) and eventually precipitation of Ca- and Fe-antimonates (tripuhyite; FeSbO4) occurred. We conclude that Fe-rich, sulfuric acid waste is efficient to immobilize Sb in APC residues from waste incineration. Copyright © 2013 Elsevier B.V. All rights reserved.

Waste Treatment of Chrome Residue of Chromium Recovery Process Using Calcium Carbonate

International Nuclear Information System (INIS)

Endro Kismolo; Prayitno; Nurimaniwathy

2002-01-01

The aim of the research was to apply the precipitation technology for the treatment of aqueous wastes of leather tanning industries. The chrome liquid wastes taken was the effluent from the residue of the chromium recovery process using magnesium oxide. The precipitant used was calcium carbonate. The experiments was performed by adjusting the concentration of calcium carbonate from 50 ppm, 100 ppm, 150 ppm, 200 ppm, 250 ppm, 300 ppm, 350 ppm to 400 ppm. The stirring speed was varied from 50 rpm, 75 rpm, 100 rpm, 125 rpm, 150 rpm, 175 rpm to 200 rpm. The time of mixing was varied from 30 minutes, 60 minutes, 90 minutes, 120 minutes, 150 minutes, 175 minutes and 200 minutes. The result from the experiments lead to the best condition obtained were the concentration of precipitant was 300 ppm, flow rates of mixing was 125 rpm and time of mixing was 60 minutes. At this condition the separations efficiency of chrome obtained was 99.985%. (author)

Residues from waste incineration. Final report. Rev. ed.

Energy Technology Data Exchange (ETDEWEB)

Astrup, T.; Juul Pedersen, A.; Hyks, J.; Frandsen, F.J.

2010-04-15

The overall objective of the project was to improve the understanding of the formation and characteristics of residues from waste incineration. This was done focusing on the importance of the waste input and the operational conditions of the furnace. Data and results obtained from the project have been discussed in this report according to the following three overall parts: i) mass flows and element distribution, ii) flue gas/particle partitioning and corrosion/deposition aspects, and iii) residue leaching. This has been done with the intent of structuring the discussion while tacitly acknowledging that these aspects are interrelated and cannot be separated. Overall, it was found that the waste input composition had significant impact of the characteristics of the generated residues. A similar correlation between operational conditions and residue characteristics could not be observed. Consequently, the project recommend that optimization of residue quality should focus on controlling the waste input composition. The project results showed that including specific waste materials (and thereby also excluding the same materials) may have significant effects on the residue composition, residue leaching, aerosol and deposit formation.It is specifically recommended to minimize Cl in the input waste. Based on the project results, it was found that a significant potential for optimization of waste incineration exist. (Author)

Influence of organic waste and residue mud additions on chemical, physical and microbial properties of bauxite residue sand.

Science.gov (United States)

Jones, Benjamin E H; Haynes, Richard J; Phillips, Ian R

2011-02-01

wet sieving, was greatest where poultry manure was applied. Although total organic C and soluble organic C were greater in biosolids than poultry manure treatments, the reverse was the case for microbial biomass C and basal respiration. In the biosolids and poultry manure treatments, increasing residue mud additions tended to increase soluble C, microbial biomass C and basal respiration. Germination index of watercress was highest in control samples and reduced by additions of biosolids and poultry manure which was attributed to the high EC and possibly high extractable P and NH (4) (+) . The concurrent addition of residue mud and organic wastes can improve chemical, microbial and particularly physical properties of residue sand. Future research should include neutralisation of the mud (e.g. with gypsum) and subsequent leaching to remove salts originating from both the mud and organic wastes.

Improvement of the management of residual waste in areas without thermal treatment facilities: A life cycle analysis of an Italian management district

Energy Technology Data Exchange (ETDEWEB)

Di Maria, Francesco, E-mail: francesco.dimaria@unipg.it [LAR Laboratory, Dipartimento di Ingegneria, Via G. Duranti 93, Perugia (Italy); Micale, Caterina; Morettini, Emanuela [LAR Laboratory, Dipartimento di Ingegneria, Via G. Duranti 93, Perugia (Italy); Sisani, Luciano [TSA spa, Via Case Sparse 107, Magione (Italy); Damiano, Roberto [GESENU spa, Via della Molinella 7, Perugia (Italy)

2015-10-15

Highlights: • LCA analysis of two option for residual waste management. • Exploitation of mechanical physical sorting facility for extracting recyclable from RMSW. • Processing the mechanically sorted organic fraction in bioreactor landfill. • Sensitivity analysis demonstrate high influence for impact assessment of substitution ratio for recycle materials. - Abstract: Starting from an existing waste management district without thermal treatment facilities, two different management scenarios for residual waste were compared by life cycle assessment (LCA). The adoption of a bioreactor landfill for managing the mechanically sorted organic fraction instead of bio-stabilization led to reduction of global warming and fresh water eutrophication by 50% and 10%, respectively. Extraction of recyclables from residual waste led to avoided emissions for particulate matter, acidification and resource depletion impact categories. Marginal energy and the amount of energy recovered from landfill gas marginally affected the LCA results. On the contrary the quality of the recyclables extracted can significantly modify the eco profile of the management schemes.

Radioactive waste treatment apparatus

International Nuclear Information System (INIS)

Abrams, R.F.; Chellis, J.G.

1983-01-01

Radioactive waste treatment apparatus is disclosed in which the waste is burned in a controlled combustion process, the ash residue from the combustion process is removed and buried, the gaseous effluent is treated in a scrubbing solution the pH of which is maintained constant by adding an alkaline compound to the solution while concurrently extracting a portion of the scrubbing solution, called the blowdown stream. The blowdown stream is fed to the incinerator where it is evaporated and the combustibles in the blowdown stream burned and the gaseous residue sent to the scrubbing solution. Gases left after the scrubbing process are treated to remove iodides and are filtered and passed into the atmosphere

Landfilling of waste incineration residues

DEFF Research Database (Denmark)

Christensen, Thomas Højlund; Astrup, Thomas; Cai, Zuansi

2002-01-01

Residues from waste incineration are bottom ashes and air-pollution-control (APC) residues including fly ashes. The leaching of heavy metals and salts from the ashes is substantial and a wide spectrum of leaching tests and corresponding criteria have been introduced to regulate the landfilling...

Management of solid residues in waste-to-energy and biomass systems

Energy Technology Data Exchange (ETDEWEB)

Vehlow, J.; Bergfeldt, B. [Forschungszentrum Karlsruhe GmbH Technik und Umwelt (Germany). Inst. fuer Technische Chemie; Wilen, C.; Ranta, J. [VTT Technical Research Centre of Finland, Espoo (Finland); Schwaiger, H. [Forschungsgesellschaft Joanneum mbH, Graz (Austria); Visser, H.J.M. [ECN Energy Research Centre of the Netherlands, Petten (Netherlands); Gu, S.; Gyftopoulou, E.; Brammer, J. [Aston Univ., Birmingham (United Kingdom)

2007-12-15

A literature review has been performed for getting in-depth information about quality of residues from thermal processes for waste and biomass as well as their disposal or utilisation options and current practices. Residues from waste incineration have been subject to intense research programs for many years and it can be concluded that the quality of bottom ashes has meanwhile a high standard. The question whether an utilisation as secondary building material is accepted or not depends on the definition of acceptable economic impac. For filter ashes and gas cleaning residues the situation is more complex. Their quality is known: due to their high inventory of heavy metals and organic micro-pollutants they are classified as hazardous waste which means they require specific measures for their safe long-term disposal. A number of stabilisation and treatment processes for filter ashes and gas cleaning residues including the recovery of species out of these materials have been developed but none has been implemented in full scale due to economic constraints. There is reason to speculate that even recovery processes which are not profitable for private companies might point out economically useful if future and long-term costs which have to be covered of the society, e.g. for rehabilitation of contaminated sites, are taken into account. Their quality as well as that of residues from combustion of contaminated biomass is mainly depending on the quality of the fuel. The inventory of critical ingredients in fuel produced from waste or waste fractions, especially of halogens and heavy metals, is often rather high and shows typically a wide range of variation. A reliable quality control for such fuels is very difficult. Other residues can - like gas cleaning residues from waste incineration - be inertised in order to meet the criteria for the access to cheaper landfills than those for hazardous waste. A similar conclusion can be drawn for the quality and management of

Dynamic effects of soil bulk density on denitrification and mineralisation by 15N labelled lettuce residue and paper wastes

International Nuclear Information System (INIS)

Hua Luo; Cheng Qing; Vinten, A.J.A.

1997-10-01

Two laboratory incubation experiments aimed to study the denitrification and mineralisation influenced by different additives ( 15 N labelled lettuce residue, paper wastes and mixture of both) and soil bulk densities were carried out by means of acetylene inhibition at the constant 15 degree C for 107 and 90 days, respectively. The results showed that the changes of N 2 O, CO 2 emission rates, inorganic nitrogen (NO 3 - and NH 4 + ), total N and 15 N abundance in the soils which were affected by adding lettuce residue, paper wastes and mixture of both were investigated. Soil denitrification rate increased after lettuce residue was added into soil for 8 days. The maximum rate of N 2 O emission was 15 times higher than that in soil without any additive. However, paper wastes did not increase N 2 O emission in the first 8 days compared with other treatments, mixed residue and paper wastes could promote soil microbial activity, but N 2 O emission was lower than that in the soil with lettuce residue added and higher than that with paper wastes, indicating that mixture of residue and paper wastes was benefit to soil nitrogen immobilisation. CO 2 emission in all the treatments were declined to the same level on the 107 th day. In the treatment added mixed residues and paper wastes, the released CO 2 quantities were higher than those in other treatments every day. Effect of different bulk density on N 2 O and CO 2 emission were response to the change of bulk density, it seems that N 2 O and CO 2 emission increased with bulk density. High bulk density could affect decomposition of paper wastes and NO 3 - , NH 4 + concentration. (30 ref., 10 tabs.)

Alternatives of Treatment and Final Disposition of the Solid Hospital residuals

International Nuclear Information System (INIS)

Meza Monge, K.

1998-01-01

The current handling, treatment and final disposition of the hospital solid waste in Costa Rica are considered inadequate or at least insufficient. This situation represents a serious danger for the population's health and the environment, because they are exposed to infectious agents, toxic substances and even radioactive products that are generated among the residuals of the centers of health. This work, alternatives propose for the treatment and adequate final disposition of the solid waste produced in the hospitals of the country. They take into consideration the characteristics that present these residuals, the advantages and disadvantages of each one of the existent techniques and the technical and economic possibilities of the country. For this purpose, in first instance, a revision about the properties, the quality and the quantity of the solid waste produced by the national hospital centers was carried out. Also, a diagnostic of the current situation of the treatment and final disposition of these residuals in some of the most important hospitals of the country, as well as of the possibilities of physical space with that they count on was carried out. Then, the existent different treatment techniques and final disposition for the solid waste that comes from the centers of health are described, as well as their advantages and disadvantages and a comparative analysis of the same ones is carried out. The objective is completed, since alternatives of treatment and final disposition that are considered appropriate for this type of residuals are planned. Nevertheless, in the future, more detailed investigations and studies of feasibility, with the purpose of developing handling programs and elimination of the solid waste for each one of the hospital centers in Costa Rica should be carried out. (Author) [es

Drying of residue and separation of nitrate salts in the sludge waste for the lagoon sludge treatment

International Nuclear Information System (INIS)

Hwang, D. S.; Lee, K. I.; Choi, Y. D.; Hwang, S. T.; Park, J. H.

2003-01-01

This study investigated the dissolution property of nitrate salts in the dissolution process by water and the drying property of residue after separating nitrates in a series of the processes for the sludge treatment. Desalination was carried out with the adding ratio of water and drying property was analyzed by TG/DTA, FTIR, and XRD. Nitrate salts involved in the sludge were separated over 97% at the water adding ratio of 2.5. But a small quantity of calcium and sodium nitrate remained in the residue These were decomposed over 600 .deg. C and calcium carbonate, which was consisted mainly of residue, was decomposed into calcium oxide over 750 .deg. C. The residue have to be decomposed over 800 .deg. C to converse uranyl nitrate of six value into the stable U 3 O 8 of four value. As a result of removing the nitrates at the water adding ratio of 2.5 and drying the residue over 900 .deg. C, volume of the sludge waste decreased over 80%

Hanford tank residual waste - Contaminant source terms and release models

International Nuclear Information System (INIS)

Deutsch, William J.; Cantrell, Kirk J.; Krupka, Kenneth M.; Lindberg, Michael L.; Jeffery Serne, R.

2011-01-01

Highlights: → Residual waste from five Hanford spent fuel process storage tanks was evaluated. → Gibbsite is a common mineral in tanks with high Al concentrations. → Non-crystalline U-Na-C-O-P ± H phases are common in the U-rich residual. → Iron oxides/hydroxides have been identified in all residual waste samples. → Uranium release is highly dependent on waste and leachant compositions. - Abstract: Residual waste is expected to be left in 177 underground storage tanks after closure at the US Department of Energy's Hanford Site in Washington State, USA. In the long term, the residual wastes may represent a potential source of contamination to the subsurface environment. Residual materials that cannot be completely removed during the tank closure process are being studied to identify and characterize the solid phases and estimate the release of contaminants from these solids to water that might enter the closed tanks in the future. As of the end of 2009, residual waste from five tanks has been evaluated. Residual wastes from adjacent tanks C-202 and C-203 have high U concentrations of 24 and 59 wt.%, respectively, while residual wastes from nearby tanks C-103 and C-106 have low U concentrations of 0.4 and 0.03 wt.%, respectively. Aluminum concentrations are high (8.2-29.1 wt.%) in some tanks (C-103, C-106, and S-112) and relatively low ( 2 -saturated solution, or a CaCO 3 -saturated water. Uranium release concentrations are highly dependent on waste and leachant compositions with dissolved U concentrations one or two orders of magnitude higher in the tests with high U residual wastes, and also higher when leached with the CaCO 3 -saturated solution than with the Ca(OH) 2 -saturated solution. Technetium leachability is not as strongly dependent on the concentration of Tc in the waste, and it appears to be slightly more leachable by the Ca(OH) 2 -saturated solution than by the CaCO 3 -saturated solution. In general, Tc is much less leachable (<10 wt.% of the

Metallic elements fractionation in municipal solid waste incineration residues

Science.gov (United States)

Kowalski, Piotr R.; Kasina, Monika; Michalik, Marek

2016-04-01

Municipal solid waste incineration (MSWI) residues are represented by three main materials: bottom ash, fly ash and air pollution control (APC) residues. Among them ˜80 wt% is bottom ash. All of that materials are products of high temperature (>1000° C) treatment of waste. Incineration process allows to obtain significant reduction of waste mass (up to 70%) and volume (up to 90%) what is commonly used in waste management to reduce the amount need to be landfilled or managed in other way. Incineration promote accumulation non-combustible fraction of waste, which part are metallic elements. That type of concentration is object of concerns about the incineration residues impact on the environment and also gives the possibility of attempts to recover them. Metallic elements are not equally distributed among the materials. Several factors influence the process: melting points, volatility and place and forms of metallic occurrence in the incinerated waste. To investigate metallic elements distribution in MSWI residues samples from one of the biggest MSW incineration plant in Poland were collected in 2015. Chemical analysis with emphasis on the metallic elements content were performed using inductively coupled plasma optical emission (ICP-OES) and mass spectrometry (ICP-MS). The bottom ash was a SiO2-CaO-Al2O3-Fe2O3-Na2O rich material, whereas fly ash and APC residues were mostly composed of CaO and SiO2. All of the materials were rich in amorphous phase occurring together with various, mostly silicate crystalline phases. In a mass of bottom ash 11 wt% were metallic elements but also in ashes 8.5 wt% (fly ash) and ˜4.5 wt% (APC residues) of them were present. Among the metallic elements equal distribution between bottom and fly ash was observed for Al (˜3.85 wt%), Mn (770 ppm) and Ni (˜65 ppm). In bottom ash Fe (5.5 wt%), Cr (590 ppm) and Cu (1250 ppm) were concentrated. These values in comparison to fly ash were 5-fold higher for Fe, 3-fold for Cu and 1.5-fold for

Treatment and immobilization of intermediate-level radioactive wastes

International Nuclear Information System (INIS)

Lerch, R.E.; Greenhalgh, W.O.; Partridge, J.A.; Richardson, G.L.

1979-01-01

A new program underway at the Hanford Engineering Development Laboratory (HEDL) to develop and demonstrate treatment and immobilization technologies for intermediate-level wastes (ILW) generated in the nuclear fuel cycle is discussed. ILW are defined as those liquid and solid radioactive wastes, other than high-level wastes and fuel cladding hulls, that in packaged form have radiation dose readings greater than 200 millirem/hr at the packaged surface and 10 millirem/hr at three feet from the surface. The IAEA value of 10 4 Ci/m 3 for ILW defines the upper limit. For comparative purposes, reference is also made to certain aspects of low-level radioactive wastes (LLW). Initial work has defined the sources, quantities and types of wastes which comprise ILW. Because of the wide differences in composition (e.g., acids, salt solutions, resins and zeolites, HEPA filters, etc.) the wastes may require different treatments, particularly those wastes containing volatile contaminants. The various types of ILW have been grouped into categories amenable to similar treatment. Laboratory studies are underway to define treatment technologies for liquid ILW which contain volatile contaminants and to define immobilization parameters for the residues resulting from treatment of ILW. Immobilization agents initially being evaluated for the various residues include cement, urea-formaldehyde, and bitumen although other immobilization agents will be studied. The program also includes development of acceptable test procedures for the final immobilized products as well as development of proposed criteria for storage, transportation, and disposal of the immobilized ILW

Viimsi water treatment plant for Ra removal: NORM residue/waste generation, radiation safety issues, and regulatory response

Energy Technology Data Exchange (ETDEWEB)

Kiisk, M.; Suursoo, S.; Realo, E.; Jantsikene, A.; Lumiste, L.; Vaeaer, K.; Isakar, K.; Koch, R. [University of Tartu (Estonia)

2014-07-01

In early 2012, the first large-scale water treatment plant, specifically designed to remove Ra-isotopes from groundwater, was commissioned in Viimsi parish, North-Estonia. The plant serves approximately 15 000 consumers with maximum production capacity of 6000 m{sup 3}/d. The chosen water treatment technology is chemical free and is based on co-precipitation and adsorption with Fe(OH){sub 3} and MnO{sub 2} flocks, and adsorption of residual Ra onto zeolite sand. The chosen technology is a complex approach and is designed to reduce high Fe and Mn concentrations as well as dissolved gases along with Ra isotopes. It is proved to be well adapted with hydro-chemical conditions of the groundwater feeding the plant. As the novel technology has been applied for the first time on a large scale, the plant was taken under long-term investigation when commissioned. The latter focuses on three areas: Ra removal efficiency and its dynamics, build-up of radioactive waste, and radiation safety. The average Ra-226 and Ra-228 activity concentrations in raw water feeding the plant are approximately 0.5 Bq/L and 0.6 Bq/L, respectively, resulting in total indicative dose of 0.4 mSv/y. Operating conditions of the plant are restricted by the established indicative value of 0.1 mSv/y for drinking water, i.e. a minimum 75% removal efficiency for Ra is required. Results of the studies show that the plant operates at Ra-removal efficiency of 98% or higher without the need of regeneration or replacement of filtering materials within the first two years. Measurements confirm that ∼90% of Ra accumulates in the solid filter media, 8-9% is washed out by backwash system as liquid effluent and 1-2% is fed on to the consumer distribution network. It has been calculated that at the level of current production capacity (below 3000 m{sup 3}/d) the yearly accumulation rate in the plant is approximately 300 and 400 MBq/y for Ra-226 and Ra-228, respectively. These values strongly exceed the exemption

Characterisation of some South African water treatment residues ...

African Journals Online (AJOL)

2005-07-03

Jul 3, 2005 ... Land application of water treatment residue (WTR) the by-product from the production of potable water, is becoming the preferred ... were analysed for some physical (particle size distribution, particle density and plant available water) and chemical attributes ...... for Industrial Wastes – Theory and Practice.

Combining mechanical-biological residual waste treatment plants with the carbonisation-combustion process; Kombination MBA mit dem Schwel-Brenn-Verfahren

Energy Technology Data Exchange (ETDEWEB)

Diekmann, J.; Wiehn, G. [Siemens AG Unternehmensbereich KWU, Erlangen (Germany). Bereich Energieerzeugung

1998-09-01

The disposal market for household waste is strongly influenced by the legal framework governing it. A further factor that makes it difficult for the authorities responsible for disposal to decide on residual waste disposal by means of thermal or mechanical-biological treatment plants is the downward pressure on disposal prices from inexpensive, underused landfills. This makes it all the more important for a future-oriented waste management to develop a both economically and ecologically optimised waste disposal concept. In this situation there is much in favour of adopting a concept consisting of a combination of mechanical, mechanical-biological, and thermal treatment which takes due account of waste disposal concepts at the regional and supraregional scale. [Deutsch] Der Entsorgungsmarkt fuer Siedlungsabfaelle wird stark durch die Entwicklung der rechtlichen Rahmenbedingungen beeinflusst. Hinzu kommt, dass der Entscheidungsprozess der oeffentlichen Entsorgungstraeger zur Restabfallentsorgung mittels thermischer oder mechanisch-biologischer Anlagen durch den Druck auf die Entsorgungspreise aufgrund der kostenguenstigen, nicht ausgelasteten Deponien erschwert wird. Umso mehr muss das Ziel einer zukunftsorientierten Abfallwirtschaft sein, unter oekonomischen und oekologischen Gesichtspunkten ein optimiertes Abfallkonzept aufzubauen. Hier kann es sehr hilfreich sein, sich eines Konzeptes, bestehend aus der Kombination von mechanischer, mechanisch-biologischer und thermischer Behandlung unter Beruecksichtigung des regionalen und ueberregionalen Abfallkonzeptes zu bedienen. (orig./SR)

Treatment and immobilization of intermediate level radioactive wastes

International Nuclear Information System (INIS)

Lerch, R.E.; Greenhalgh, W.O.; Partridge, J.A.; Richardson, G.L.

1977-01-01

This paper discusses a new program underway to develop and demonstrate treatment and immobilization technologies for intermediate level wastes (ILW) generated in the nuclear fuel cycle. Initial work has defined the sources, quantities and types of wastes which comprise ILW. Laboratory studies are underway to define treatment technologies for liquid ILW which contains volatile contaminants and to define immobilization parameters for the residues resulting from treatment of ILW. Immobilization agents initially being evaluated for the various residues include cement, urea-formaldehyde, and bitumen although other immobilization agents will be studied. The program also includes development of acceptable test procedures for the final immobilized products as well as development of proposed criteria for storage, transportation, and disposal of the immobilized ILW. 20 figures, 10 tables

Disposal of residue from sifting of combustible waste; Avsaettning av siktrest fraan foerbehandling av braennbart avfall

Energy Technology Data Exchange (ETDEWEB)

Niklasson, Fredrik

2012-11-01

In waste to energy plants, unwanted species in the fuel may cause corrosion, deposits, agglomeration in the fuel bed, and emissions of pollutants. Countermeasures to such problems are often costly. For at least some of the waste, the fuel properties can be improved by introducing a pretreatment system in which the fine fraction is separated from the waste by sifting. This method has been studied in an earlier Waste Refinery project, WR-06. That study pointed at advantages in performance of the boiler plant and a rough economical analysis indicated substantial benefits. The drawback of the pretreatment was that the residue (the fine fraction) showed as high content of total organic carbon (TOC) as 37 %, by weight. Such a waste fraction is not allowed to be landfilled in Sweden. High TOC content is also a limiting factor for usage as a secondary construction material. To become an applicable pretreatment method, it is necessary to find an appropriate disposal method for the residue material. Present work investigates different possibilities to handle the sifting residue, assuming it has the same properties as in previous study. The residue from sifting needs further treatment, preferably with energy recovery. There are some alternatives, such as combustion, gasification, anaerobic or aerobic digestion. To reduce problems associated by combustion, the waste may be burnt in another more suitable furnace. An alternative is gasification, but that treatment method is not yet an established process for waste fuels. Another option is treatment by anaerobic or aerobic digestion. The high concentrations of metals, however, limit the use of the biologically treated waste to landfilling sites, where it may be utilized as a construction material. The high metal concentrations in the sifting residue imply that it must be kept separate from other biodegradable wastes which are used to produce fertilizers. Thus, this treatment alternative will likely require substantial new

Research on Toxicity Evaluation of Waste Incineration Residues of Printed Circuit Boards

Directory of Open Access Journals (Sweden)

Rasa Volungevičienė

2014-10-01

Full Text Available Recycling waste printed circuit boards (PCB is an extremely complicated process, because PCBs consist of a number of complex components – hazardous and non-hazardous materials sets. Pyrolysis and combustion are currently the most effective treatment technologies for waste printed circuit boards. Pyrolysis can be used for thermally decomposing PCBs allowing for the simultaneous recovery of valuable materials. Following the extraction of valuable materials, the problem of residual ash utilization is encountered. Determining the qualitative and quantitative characteristics of incineration residue helps with choosing effective ash management technologies. This paper analyzes PCB ash generated at three different temperatures of 400 °C, 500 °C and 600 °C. Ash residues have been analysed to determine the quantity and type of metals present. Furthermore, the experiment of leaching heavy metals from ash has been described.

Alternatives for managing wastes from reactors and post-fission operations in the LWR fuel cycle. Volume 2. Alternatives for waste treatment

International Nuclear Information System (INIS)

1976-05-01

Volume II of the five-volume report is devoted to the description of alternatives for waste treatment. The discussion is presented under the following section titles: fuel reprocessing modifications; high-level liquid waste solidification; treatment and immobilization of chop-leach fuel bundle residues; treatment of noncombustible solid wastes; treatment of combustible wastes; treatment of non-high-level liquid wastes; recovery of transuranics from non-high-level wastes; immobilization of miscellaneous non-high-level wastes; volatile radioisotope recovery and off-gas treatment; immobilization of volatile radioisotopes; retired facilities (decontamination and decommissioning); and, modification and use of selected fuel reprocessing wastes

Alternatives for managing wastes from reactors and post-fission operations in the LWR fuel cycle. Volume 2. Alternatives for waste treatment

Energy Technology Data Exchange (ETDEWEB)

1976-05-01

Volume II of the five-volume report is devoted to the description of alternatives for waste treatment. The discussion is presented under the following section titles: fuel reprocessing modifications; high-level liquid waste solidification; treatment and immobilization of chop-leach fuel bundle residues; treatment of noncombustible solid wastes; treatment of combustible wastes; treatment of non-high-level liquid wastes; recovery of transuranics from non-high-level wastes; immobilization of miscellaneous non-high-level wastes; volatile radioisotope recovery and off-gas treatment; immobilization of volatile radioisotopes; retired facilities (decontamination and decommissioning); and, modification and use of selected fuel reprocessing wastes. (JGB)

Recycling of air pollution control residues from municipal solid waste incineration into lightweight aggregates.

Science.gov (United States)

Quina, Margarida J; Bordado, João M; Quinta-Ferreira, Rosa M

2014-02-01

This work focuses on the assessment of technological properties and on the leaching behavior of lightweight aggregates (LWA) produced by incorporating different quantities of air pollution control (APC) residues from municipal solid waste (MSW) incineration. Currently this hazardous waste has been mostly landfilled after stabilization/solidification. The LWA were produced by pelletizing natural clay, APC residues as-received from incineration plant, or after a washing treatment, a small amount of oil and water. The pellets were fired in a laboratory chamber furnace over calcium carbonate. The main technological properties of the LWA were evaluated, mainly concerning morphology, bulk and particle densities, compressive strength, bloating index, water adsorption and porosity. Given that APC residues do not own expansive (bloating) properties, the incorporation into LWA is only possible in moderate quantities, such as 3% as received or 5% after pre-washing treatment. The leaching behavior of heavy metals from sintered LWA using water or acid solutions was investigated, and despite the low acid neutralization capacity of the synthetic aggregates, the released quantities were low over a wide pH range. In conclusion, after a washing pre-treatment and if the percentage of incorporation is low, these residues may be incorporated into LWA. However, the recycling of APC residues from MSW incineration into LWA does not revealed any technical advantage. Copyright © 2013 Elsevier Ltd. All rights reserved.

Treatment methods for radioactive mixed wastes in commercial low-level wastes: technical considerations

International Nuclear Information System (INIS)

MacKenzie, D.R.; Kempf, C.R.

1986-01-01

Treatment options for the management of three generic categories of radioactive mixed waste in commercial low-level wastes (LLW) have been identified and evaluated. These wastes were characterized as part of a BNL study in which LLW generators were surveyed for information on potential chemical hazards in their wastes. The general treatment options available for mixed wastes are destruction, immobilization, and reclamation. Solidification, absorption, incineration, acid digestion, wet-air oxidation, distillation, liquid-liquid wastes. Containment, segregation, decontamination, and solidification or containment of residues, have been considered for lead metal wastes which have themselves been contaminated and are not used for purposes of waste disposal shielding, packaging, or containment. For chromium-containing wastes, solidification, incineration, wet-air oxidation, acid digestion, and containment have been considered. For each of these wastes, the management option evaluation has included an assessment of testing appropriate to determine the effect of the option on both the radiological and potential chemical hazards present

Treatment methods for radioactive mixed wastes in commercial low-level wastes: technical considerations

Energy Technology Data Exchange (ETDEWEB)

MacKenzie, D.R.; Kempf, C.R.

1986-01-01

Treatment options for the management of three generic categories of radioactive mixed waste in commercial low-level wastes (LLW) have been identified and evaluated. These wastes were characterized as part of a BNL study in which LLW generators were surveyed for information on potential chemical hazards in their wastes. The general treatment options available for mixed wastes are destruction, immobilization, and reclamation. Solidification, absorption, incineration, acid digestion, wet-air oxidation, distillation, liquid-liquid wastes. Containment, segregation, decontamination, and solidification or containment of residues, have been considered for lead metal wastes which have themselves been contaminated and are not used for purposes of waste disposal shielding, packaging, or containment. For chromium-containing wastes, solidification, incineration, wet-air oxidation, acid digestion, and containment have been considered. For each of these wastes, the management option evaluation has included an assessment of testing appropriate to determine the effect of the option on both the radiological and potential chemical hazards present.

WEEE and portable batteries in residual household waste: Quantification and characterisation of misplaced waste

Energy Technology Data Exchange (ETDEWEB)

Bigum, Marianne, E-mail: mkkb@env.dtu.dk [Technical University of Denmark, Department of Environmental Engineering, Miljøvej 113, 2500 Kgs. Lyngby (Denmark); Petersen, Claus, E-mail: claus_petersen@econet.dk [Econet A/S, Strandboulevarden 122, 5, 2100 København Ø (Denmark); Christensen, Thomas H., E-mail: thho@env.dtu.dk [Technical University of Denmark, Department of Environmental Engineering, Miljøvej 113, 2500 Kgs. Lyngby (Denmark); Scheutz, Charlotte, E-mail: chas@env.dtu.dk [Technical University of Denmark, Department of Environmental Engineering, Miljøvej 113, 2500 Kgs. Lyngby (Denmark)

2013-11-15

Highlights: • We analyse 26.1 Mg of residual waste from 3129 Danish households. • We quantify and characterise misplaced WEEE and portable batteries. • We compare misplaced WEEE and batteries to collection through dedicated schemes. • Characterisation showed that primarily small WEEE and light sources are misplaced. • Significant amounts of misplaced batteries were discarded as built-in WEEE. - Abstract: A total of 26.1 Mg of residual waste from 3129 households in 12 Danish municipalities was analysed and revealed that 89.6 kg of Waste Electrical and Electronic Equipment (WEEE), 11 kg of batteries, 2.2 kg of toners and 16 kg of cables had been wrongfully discarded. This corresponds to a Danish household discarding 29 g of WEEE (7 items per year), 4 g of batteries (9 batteries per year), 1 g of toners and 7 g of unidentifiable cables on average per week, constituting 0.34% (w/w), 0.04% (w/w), 0.01% (w/w) and 0.09% (w/w), respectively, of residual waste. The study also found that misplaced WEEE and batteries in the residual waste constituted 16% and 39%, respectively, of what is being collected properly through the dedicated special waste collection schemes. This shows that a large amount of batteries are being discarded with the residual waste, whereas WEEE seems to be collected relatively successfully through the dedicated special waste collection schemes. Characterisation of the misplaced batteries showed that 20% (w/w) of the discarded batteries were discarded as part of WEEE (built-in). Primarily alkaline batteries, carbon zinc batteries and alkaline button cell batteries were found to be discarded with the residual household waste. Characterisation of WEEE showed that primarily small WEEE (WEEE directive categories 2, 5a, 6, 7 and 9) and light sources (WEEE directive category 5b) were misplaced. Electric tooth brushes, watches, clocks, headphones, flashlights, bicycle lights, and cables were items most frequently found. It is recommended that these

Hanford Tank 241-S-112 Residual Waste Composition and Leach Test Data

Energy Technology Data Exchange (ETDEWEB)

Cantrell, Kirk J.; Krupka, Kenneth M.; Geiszler, Keith N.; Lindberg, Michael J.; Arey, Bruce W.; Schaef, Herbert T.

2008-08-29

This report presents the results of laboratory characterization and testing of two samples (designated 20406 and 20407) of residual waste collected from tank S-112 after final waste retrieval. These studies were completed to characterize the residual waste and assess the leachability of contami¬nants from the solids. This is the first report from this PNNL project to describe the composition and leach test data for residual waste from a salt cake tank. All previous PNNL reports (Cantrell et al. 2008; Deutsch et al. 2006, 2007a, 2007b, 2007c) describing contaminant release models, and characterization and testing results for residual waste in single-shell tanks were based on samples from sludge tanks.

Treatment of alpha-bearing combustible wastes using acid digestion

International Nuclear Information System (INIS)

Lerch, R.E.; Allen, C.R.; Blasewitz, A.G.

1978-01-01

Acid digestion has been developed at the Hanford Engineering Development Laboratory (HEDL) in Richland, Washington to reduce the volume of combustible nuclear waste materials, while converting them to an inert, noncombustible residue. A 100 kg/day test unit has recently been constructed to demonstrate the process using radioactively contaminated combustible wastes. The unit, called the Radioactive Acid Digestion Test Unit (RADTU) was completed in September 1977 and is currently undergoing cold shakedown tests. Hot operation is expected in May 1978. Features of RADTU include: storage and transfer station for incoming wastes, a feed preparation station, an extrusion feed mechanism for transfer of the waste to the acid digester, the acid digester a residue recovery system, and an off-gas treatment system

Treatment of alpha-bearing combustible wastes using acid digestion

International Nuclear Information System (INIS)

Lerch, R.E.; Allen, C.R.; Blasewitz, A.G.

1977-11-01

Acid digestion has been developed at the Hanford Engineering Development Laboratory (HEDL) in Richland, Washington to reduce the volume of combustible nuclear waste materials, while converting them to an inert, noncombustible residue. A 100 kg/day test unit has recently been constructed to demonstrate the process using radioactively contaminated combustible wastes. The unit, called the Radioactive Acid Digestion Test Unit (RADTU) was completed in September 1977 and is currently undergoing cold shakedown tests. Hot operation is expected in May 1978. Features of RADTU include: storage and transfer station for incoming wastes, a feed preparation station, an extrusion feed mechanism for transfer of the waste to the acid digester, the acid digester, a residue recovery system, and an off-gas treatment system

Demonstration of New Technologies Required for the Treatment of Mixed Waste Contaminated with {ge}260 ppm Mercury

Energy Technology Data Exchange (ETDEWEB)

Morris, M.I.

2002-02-06

The Resource Conservation and Recovery Act (RCRA) defines several categories of mercury wastes, each of which has a defined technology or concentration-based treatment standard, or universal treatment standard (UTS). RCRA defines mercury hazardous wastes as any waste that has a TCLP value for mercury of 0.2 mg/L or greater. Three of these categories, all nonwastewaters, fall within the scope of this report on new technologies to treat mercury-contaminated wastes: wastes as elemental mercury; hazardous wastes with less than 260 mg/kg [parts per million (ppm)] mercury; and hazardous wastes with 260 ppm or more of mercury. While this report deals specifically with the last category--hazardous wastes with 260 ppm or more of mercury--the other two categories will be discussed briefly so that the full range of mercury treatment challenges can be understood. The treatment methods for these three categories are as follows: Waste as elemental mercury--RCRA identifies amalgamation (AMLGM) as the treatment standard for radioactive elemental mercury. However, radioactive mercury condensates from retorting (RMERC) processes also require amalgamation. In addition, incineration (IMERC) and RMERC processes that produce residues with >260 ppm of radioactive mercury contamination and that fail the RCRA toxicity characteristic leaching procedure (TCLP) limit for mercury (0.20 mg/L) require RMERC, followed by AMLGM of the condensate. Waste with <260 ppm mercury--No specific treatment method is specified for hazardous wastes containing <260 ppm. However, RCRA regulations require that such wastes (other than RMERC residues) that exceed a TCLP mercury concentration of 0.20 mg/L be treated by a suitable method to meet the TCLP limit for mercury of 0.025 mg/L. RMERC residues must meet the TCLP value of {ge}0.20 mg/L, or be stabilized and meet the {ge}0.025 mg/L limit. Waste with {ge}260 ppm mercury--For hazardous wastes with mercury contaminant concentrations {ge}260 ppm and RCRA

Treatment and disposal of radioactive waste from nuclear power stations

International Nuclear Information System (INIS)

Baehr, W.

1981-01-01

The Federal Republic of Germany and many other European countries, having very high population densities, must make the most efficient use of their soil, their ground and surface waters. In Germany, no method of waste disposal could be used which included direct storage or seepage into the upper strata of the soil or a discharge into rivers or lakes. It has been shown after more than 20 years experience of treatment of low and intermediate level liquid and solid wastes and disposal of solidified residues in a salt mine, that a number of techniques and procedures are available for manageing this kind of waste with a high degree of safety. A complete system of waste collection, treatment methods and controlled disposal of low and intermediate radioactive residues in accordance with legally established rules and regulations offers the best guarantee for environmental protection. (orig./RW)

Electrodialytic remediation of municipal solid waste incineration residues using different membranes

DEFF Research Database (Denmark)

Parés Viader, Raimon; Jensen, Pernille Erland; Ottosen, Lisbeth M.

2017-01-01

In the present work, three different commercial membrane brands were used in an identical electrodialytic cell setup and operating conditions, in order to reduce the leaching of metals and salt anions of two types of municipal solid waste incineration residues: air pollution control residues...... as a technology to upgrade municipal solid waste incineration residues....

Anaerobic treatment of solid and liquid residues. Papers

International Nuclear Information System (INIS)

Maerkl, H.; Stegmann, R.

1994-01-01

Anaerobic processes are getting increasing attention in the disposal of liquid waste of the food industry and chemical industry and solid organic residues of the municipal sector. The main advantages of anaerobic processes are the favourable energy balance and the comparatively small volume of new biomass produced. There are new satisfactory technical solutions for nearly all problems encountered in practice. A conference on ''Anaerobic treatment of solid and liquid residues'' was held on 2-4 November 1994. The state of the art and new developments were presented in lectures by experts from research and practice. (orig.) [de

Treatment methods for radioactive mixed wastes in commercial low-level wastes - technical considerations

International Nuclear Information System (INIS)

MacKenzie, D.R.; Kempf, C.R.

1986-01-01

Treatment options for the management of three generic categories of radioactive mixed waste in commercial low-level wastes (LLW) have been identified and evaluated. These wastes were characterized as part of a BNL study in which LLW generators were surveyed for information on potential chemical hazards in their wastes. The general treatment options available for mixed wastes are destruction, immobilization, and reclamation. Solidification, absorption, incineration, acid digestion, wet-air oxidation, distillation, liquid-liquid solvent extraction, and specific chemical destruction techniques have been considered for organic liquid wastes. Containment, segregation, decontamination, and solidification or containment of residues, have been considered for lead metal wastes which have themselves been contaminated and are not used for purposes of waste disposal shielding, packaging, or containment. For chromium-containing wastes, solidification, incineration, wet-air oxidation, acid digestion, and containment have been considered. Fore each of these wastes, the management option evaluation has included an assessment of testing appropriate to determine the effect of the option on both the radiological and potential chemical hazards present

Conditioning of high activity solid waste: fuel claddings and dissolution residues

International Nuclear Information System (INIS)

Anon.

1982-01-01

This chapter reports on experimental studies of embedding into matrix material, the melting and conversion of zircaloy, and waste properties and characterization. Methods are developed for embedding the waste scrap into a solid and resistant matrix material in order to confine the radioactivity and to prevent it from dispersion. The matrix materials investigated are lead alloys, ceramics and compacted graphite or aluminium powder. The treatment of fuel hulls by melting or chemical conversion is described. Cemented hulls are characterized and the pyrophoricity of zircaloy fines is investigated. Topics considered include the embedding of hulls into graphite and aluminium, the embedding of hulls and dissolution residues into alumino-ceramics, the solidification of alpha-bearing wastes into a ceramic matrix, and the conditioning of cladding waste by eutectoidic melting and by embedding in glass

Thermal treatment of stabilized air pollution control residues in a waste incinerator pilot plant. Part 2: Leaching characteristics of bottom ashes.

Science.gov (United States)

Baun, Dorthe L; Christensen, Thomas H; Bergfeldt, Brita; Vehlow, Jürgen; Mogensen, Erhardt P B

2004-02-01

With the perspective of generating only one solid residue from waste incineration, co-feeding of municipal solid waste and air pollution control residues stabilized by the Ferrox process was investigated in the TAMARA pilot plant incinerator as described in Bergfeldt et al. (Waste Management Research, 22, 49-57, 2004). This paper reports on leaching from the combined bottom ashes. Batch leaching test, pH-static leaching tests, availability tests and column leaching tests were used to characterize the leaching properties. The leaching properties are key information in the context of reuse in construction or in landfilling of the combined residue. In general, the combined bottom ashes had leaching characteristics similar to the reference bottom ash, which contained no APC residue. However, As and Pb showed slightly elevated leaching from the combined bottom ashes, while Cr showed less leaching. The investigated combined bottom ashes had contents of metals comparable to what is expected at steady state after continuous co-feeding of APC residues. Only Cd and Pb were partly volatilized (30-40%) during the incineration process and thus the combined bottom ashes had lower contents of Cd and Pb than expected at steady state. Furthermore, a major loss of Hg was, not surprisingly, seen and co-feeding of Ferrox-products together with municipal solid waste will require dedicated removal of Hg in the flue gas to prevent a build up of Hg in the system. In spite of this, a combined single solid residue from waste incineration seems to be a significant environmental improvement to current technology.

Evaluation of Secondary Streams in Mixed Waste Treatment

International Nuclear Information System (INIS)

Haywood, Fred F.; Goldsmith, William A.; Allen, Douglas F.; Mezga, Lance J.

1995-12-01

The United States Department of Energy (DOE) and its predecessors have generated waste containing radioactive and hazardous chemical components (mixed wastes) for over 50 years. Facilities and processes generating these wastes as well as the regulations governing their management have changed. Now, DOE has 49 sites where mixed waste streams exist. The Federal Facility Compliance Act of 1992 (1) required DOE to prepare and obtain regulatory approval of plans for treating these mixed waste streams. Each of the involved DOE sites submitted its respective plan to regulators in April 1995 (2). Most of the individual plans were approved by the respective regulatory agencies in October 1995. The implementation of these plans has begun accordance with compliance instruments (orders) issued by the cognizant regulatory authority. Most of these orders include milestones that are fixed, firm and enforceable as defined in each compliance order. In many cases, mixed waste treatment that was already being carried out and survived the alternative selection process is being used now to treat selected mixed waste streams. For other waste streams at sites throughout the DOE complex treatment methods and schedules are subject to negotiation as the realties of ever decreasing budgets begin to drive the available options. Secondary wastes generated by individual waste treatment systems are also mixed wastes that require treatment in the appropriate treatment system. These secondary wastes may be solid or liquid waste (or both). For example debris washing will generate wastewater requiring treatment; wastewater treatment, in turn, will generate sludge or other residuals requiring treatment; liquid effluents must meet applicable limits of discharge permits. At large DOE sites, secondary waste streams will be a major influence in optimizing design for primary treatment. Understanding these impacts is important not only foe system design, but also for assurances that radiation releases and

WEEE and portable batteries in residual household waste: Quantification and characterisation of misplaced waste

DEFF Research Database (Denmark)

Bigum, Marianne Kristine; Petersen, Claus; Christensen, Thomas Højlund

2013-01-01

with the residual household waste. Characterisation of WEEE showed that primarily small WEEE (WEEE directive categories 2, 5a, 6, 7 and 9) and light sources (WEEE directive category 5b) were misplaced. Electric tooth brushes, watches, clocks, headphones, flashlights, bicycle lights, and cables were items most......A total of 26.1Mg of residual waste from 3129 households in 12 Danish municipalities was analysed and revealed that 89.6kg of Waste Electrical and Electronic Equipment (WEEE), 11kg of batteries, 2.2kg of toners and 16kg of cables had been wrongfully discarded. This corresponds to a Danish household...

Thermal treatment of high-caloric waste in fluidized bed incineration plants in Austria

International Nuclear Information System (INIS)

Ragossnig, A.M.

2001-05-01

The importance of thermal treatment of waste and residues in Austria is expected to rise due to the current changes of the legal situation in waste management. Assessing the rank order of different thermal treatment processes for waste management it has been shown that - especially caused by the rising importance of the mechanical treatment step in the mechanical-biological residual waste treatment and the subsequent necessity of the thermal treatment of a high-caloric preprocessed waste stream - the importance of the fluidized bed technology will increase. The main advantages are the high existing capacities as well as the flexibility of this technology in regard of fuel properties and further on the fact of the lacking influence of the ash towards the quality of a product. This is true although the thermal treatment in fluidized bed incinerators requires some processing of the waste. This doctoral thesis also contains a thorough physical and chemical characterization of various waste fuels - especially those which have been used during full scale incineration experiments. This characterization includes a comparison with fossil fuel. The practical part contains the documentation and balancing of full scale incineration experiments. A comparison of a reference experiment with experiments when waste fuel has been thermally utilized showed that a significant increase of emissions to the atmosphere has not been observed. Based on the incineration experiments conclusions in regard of waste fuels as well as different categories of thermal treatment plants are being stated. Finally, a recommendation of the assignation of various waste streams to different categories of thermal treatment plants is being made. (author)

Full-scale demonstration of treatment of mechanically separated organic residue in a bioreactor at VAM in Wijster

NARCIS (Netherlands)

Oonk, H.; Woelders, H.

1999-01-01

At the VAM waste treatment company in Wijster a demonstration is in progress of bioreactor technology for the treatment of mechanically separated organic residue (MSOR) of a waste separation plant. This bioreactor is an in situ fermentation cell in which physical, chemical and biological processes

Estimation of residual MSW heating value as a function of waste component recycling

International Nuclear Information System (INIS)

Magrinho, Alexandre; Semiao, Viriato

2008-01-01

Recycling of packaging wastes may be compatible with incineration within integrated waste management systems. To study this, a mathematical model is presented to calculate the fraction composition of residual municipal solid waste (MSW) only as a function of the MSW fraction composition at source and recycling fractions of the different waste materials. The application of the model to the Lisbon region yielded results showing that the residual waste fraction composition depends both on the packaging wastes fraction at source and on the ratio between that fraction and the fraction of the same material, packaging and non-packaging, at source. This behaviour determines the variation of the residual waste LHV. For 100% of paper packaging recycling, LHV reduces 4.2% whereas this reduction is of 14.4% for 100% of packaging plastics recycling. For 100% of food waste recovery, LHV increases 36.8% due to the moisture fraction reduction of the residual waste. Additionally the results evidence that the negative impact of recycling paper and plastic packaging on the LHV may be compensated by recycling food waste and glass and metal packaging. This makes packaging materials recycling and food waste recovery compatible strategies with incineration within integrated waste management systems

Study of field assessment methods and worker risks for processing alternatives to support principles for FUSRAP waste materials. Part 1: Treatment methods and comparative risks of thorium removal from waste residues

Energy Technology Data Exchange (ETDEWEB)

Porter, R.D.; Hamby, D.M.; Martin, J.E.

1997-07-01

This study was done to examine the risks of remediation and the effectiveness of removal methods for thorium and its associated radioactive decay products from various soils and wastes associated with DOE`s Formerly Utilized Sites Remedial Action Program (FUSRAP). Its purpose was to provide information to the Environmental Management Advisory Board`s FUSRAP Committee for use in its deliberation of guiding principles for FUSRAP sites, in particular the degree to which treatment should be considered in the FUSRAP Committee`s recommendations. Treatment of FUSRAP wastes to remove thorium could be beneficial to management of lands that contain thorium if such treatment were effective and cost efficient. It must be recognized, however, that treatment methods invariably require workers to process residues and waste materials usually with bulk handling techniques. These processes expose workers to the radioactivity in the materials, therefore, workers would incur radiological risks in addition to industrial accident risks. An important question is whether the potential reduction of future radiological risks to members of the public justifies the risks that are incurred by remediation workers due to handling materials. This study examines, first, the effectiveness of treatment and then the risks that would be associated with remediation. Both types of information should be useful for decisions on whether and how to apply thorium removal methods to FUSRAP waste materials.

Study of field assessment methods and worker risks for processing alternatives to support principles for FURSRAP waste materials. Part 1: Treatment methods and comparative risks of thorium removal from waste residues

International Nuclear Information System (INIS)

Porter, R.D.; Hamby, D.M.; Martin, J.E.

1997-07-01

This study was done to examine the risks of remediation and the effectiveness of removal methods for thorium and its associated radioactive decay products from various soils and wastes associated with DOE's Formerly Utilized Sites Remedial Action Program (FUSRAP). Its purpose was to provide information to the Environmental Management Advisory Board's FUSRAP Committee for use in its deliberation of guiding principles for FUSRAP sites, in particular the degree to which treatment should be considered in the FUSRAP Committee's recommendations. Treatment of FUSRAP wastes to remove thorium could be beneficial to management of lands that contain thorium if such treatment were effective and cost efficient. It must be recognized, however, that treatment methods invariably require workers to process residues and waste materials usually with bulk handling techniques. These processes expose workers to the radioactivity in the materials, therefore, workers would incur radiological risks in addition to industrial accident risks. An important question is whether the potential reduction of future radiological risks to members of the public justifies the risks that are incurred by remediation workers due to handling materials. This study examines, first, the effectiveness of treatment and then the risks that would be associated with remediation. Both types of information should be useful for decisions on whether and how to apply thorium removal methods to FUSRAP waste materials

Thermal treatment of solid residues from WtE units: a review.

Science.gov (United States)

Lindberg, Daniel; Molin, Camilla; Hupa, Mikko

2015-03-01

Thermal treatment methods of bottom ash, fly ash and various types of APC (air pollution control) residues from waste-to-energy plants can be used to obtain environmentally stable material. The thermal treatment processes are meant to reduce the leachability of harmful residue constituents, destroy toxic organic compounds, reduce residue volume, and produce material suitable for utilization. Fly ash and APC residues often have high levels of soluble salts, particularly chlorides, metals such as cadmium, lead, copper and zinc, and trace levels of organic pollutants such as dioxins and furans. Different thermal treatment methods can be used to either decompose or stabilize harmful elements and compounds in the ash, or separate them from the ash to get a material that can be safely stored or used as products or raw materials. In the present paper, thermal treatment methods, such as sintering, vitrification, and melting have been reviewed. In addition to a review of the scientific literature, a survey has been made of the extensive patent literature in the field. Copyright © 2015 Elsevier Ltd. All rights reserved.

Products derived from waste plastics (PC, HIPS, ABS, PP and PA6) via hydrothermal treatment: Characterization and potential applications.

Science.gov (United States)

Zhao, Xuyuan; Zhan, Lu; Xie, Bing; Gao, Bin

2018-05-26

In this study, hydrothermal method was applied for the treatment of five typical waste plastics (PC, HIPS, ABS, PP and PA6). The hydrothermal products of oils and solid residues were analyzed for the product slate and combustion behaviors. Some predominant chemical feedstock were detected in the oils, such as phenolic compounds and bisphenol A (BPA) in PC oils, single-ringed aromatic compounds and diphenyl-sketetons compounds in HIPS and ABS oils, alkanes in PP oils, and caprolactam (CPL) in PA6 oils. The hydrothermal solid residues were subjected to DSC analysis. Except the solid residues of PA6, all the solid residues had enormous improvement on the enthalpy of combustion. The solid residues of PC had the maximum promotion up to 576.03% compared to the raw material. The hydrothermal treatment significantly improved the energy density and facilitated effective combustion. Meanwhile, the glass fiber was recovered from the PA6 plastics. In addition, the combustion behaviors of the uplifting residues were investigated to provide the theoretical foundation for further study of combustion optimization. All the results indicated that the oils of waste plastics after hydrothermal treatment could be used as chemical feedstock; the solid residues of waste plastics after hydrothermal treatment could be used as potentially clean and efficient solid fuels. The hydrothermal treatment for various waste plastics was verified as a novel waste-to-energy technique. Copyright © 2018 Elsevier Ltd. All rights reserved.

Mixed wastes treatment in Atucha I

International Nuclear Information System (INIS)

Varani, J.L.; Comandu, J.F.

1998-01-01

Full text: During decontamination works of the fueling machine of Atucha I nuclear power plant (AINPP), a liquid waste with special characteristics was generated, which needed the development of a treatment method. The waste consisted of an emulsion designed for the cleaning of mechanical components and was formed by an organic solvent dispersed in water with aid of an emulsifier additive. After several cleaning operations, the emulsion contained an important quantity of lubricants and radioactive dirt. The treatment had the objective of recycling a toxic waste such as the organic solvent and reducing the volume of the residual mass. Laboratory tests were made tending to the emulsion separation in their components. Ionic force and ionic mobility were modified for join the emulsion micelles and produce their coalescence. Different salts and working temperatures were tried and it was stated that the combination of 1% of Na 2 SO 4 added and 40 degree C temperature were the optimum taking into account the available equipment in AINPP and cost considerations. The process was carried out in batch mode and 3 residual streams were obtained, an aqueous one which was sent to Residual Water System of AINPP, an organic liquid consisting of decontaminated hydrocarbons, useful for other cleaning tasks and finally a solid one, sited in the in-between interface of the other two liquids, consisting of insoluble soaps used as lubricant thickness, containing the principal proportion of radioactivity. As a result of this process we have achieved a volume reduction higher than 90%, the recycling of the organic solvent and concentration of radioactivity in a solid greasy mass with low water solubility. (author) [es

Instructive of chemical residues waste administration

International Nuclear Information System (INIS)

Alfaro Vargas, Ariel

2014-01-01

An instructive is established for the waste management system of chemical residues generated at the Universidad de Costa Rica, ensuring the collection, separation, transportation, reuse, recycling and final disposal. The laboratory waste management system is conditioned to the volume and type of waste generated. The respective procedures are listed in data sheets according to the corresponding model: avoid, reduce, recycle, treat, delete. The materials are identified as: expired products, materials or damaged products, substances that have lost some of the required characteristics, waste from the regular activities of the lab, unused products that now no longer used because they are considered inadequate. The chemicals reagents or hazardous are transformed into small amounts of derivatives safe products, or less hazardous, to allow for removal or to pick up a spill of these without problem [es

Thermal treatment of solid residues from WtE units: A review

International Nuclear Information System (INIS)

Lindberg, Daniel; Molin, Camilla; Hupa, Mikko

2015-01-01

Highlights: • We review the thermal treatment methods for ashes and residues from WtE plants. • We review the results from extensive laboratory work on vitrification, melting and vaporization of ash. • We analyze the results from the extensive patent literature on thermal treatment. • We review industrial concepts for thermal treatment of ash. - Abstract: Thermal treatment methods of bottom ash, fly ash and various types of APC (air pollution control) residues from waste-to-energy plants can be used to obtain environmentally stable material. The thermal treatment processes are meant to reduce the leachability of harmful residue constituents, destroy toxic organic compounds, reduce residue volume, and produce material suitable for utilization. Fly ash and APC residues often have high levels of soluble salts, particularly chlorides, metals such as cadmium, lead, copper and zinc, and trace levels of organic pollutants such as dioxins and furans. Different thermal treatment methods can be used to either decompose or stabilize harmful elements and compounds in the ash, or separate them from the ash to get a material that can be safely stored or used as products or raw materials. In the present paper, thermal treatment methods, such as sintering, vitrification, and melting have been reviewed. In addition to a review of the scientific literature, a survey has been made of the extensive patent literature in the field

Thermal treatment of solid residues from WtE units: A review

Energy Technology Data Exchange (ETDEWEB)

Lindberg, Daniel, E-mail: daniel.lindberg@abo.fi; Molin, Camilla, E-mail: camilla.molin@abo.fi; Hupa, Mikko, E-mail: mikko.hupa@abo.fi

2015-03-15

Highlights: • We review the thermal treatment methods for ashes and residues from WtE plants. • We review the results from extensive laboratory work on vitrification, melting and vaporization of ash. • We analyze the results from the extensive patent literature on thermal treatment. • We review industrial concepts for thermal treatment of ash. - Abstract: Thermal treatment methods of bottom ash, fly ash and various types of APC (air pollution control) residues from waste-to-energy plants can be used to obtain environmentally stable material. The thermal treatment processes are meant to reduce the leachability of harmful residue constituents, destroy toxic organic compounds, reduce residue volume, and produce material suitable for utilization. Fly ash and APC residues often have high levels of soluble salts, particularly chlorides, metals such as cadmium, lead, copper and zinc, and trace levels of organic pollutants such as dioxins and furans. Different thermal treatment methods can be used to either decompose or stabilize harmful elements and compounds in the ash, or separate them from the ash to get a material that can be safely stored or used as products or raw materials. In the present paper, thermal treatment methods, such as sintering, vitrification, and melting have been reviewed. In addition to a review of the scientific literature, a survey has been made of the extensive patent literature in the field.

Treatment of Lignin and Waste residues by Flash Pyrolysis

DEFF Research Database (Denmark)

Jensen, Peter Arendt; Trinh, Ngoc Trung; Dam-Johansen, Kim

pyrolysis properties were compared with the pyrolysis properti es of wood and straw. The PCR treatment of sewage sludge provides an oil that can be used for energy pur poses and a solid residue rich in in organic nutrients that may be used as fertilizer product. By fast pyroly sis of lignin from the IBUS...... be operated at low rotational speed was constructed. The new rotor systems should make it easier to make an up-scaling of the process....

Immobilization of acid digestion residue

International Nuclear Information System (INIS)

Greenhalgh, W.O.; Allen, C.R.

1983-01-01

Acid digestion treatment of nuclear waste is similar to incineration processes and results in the bulk of the waste being reduced in volume and weight to some residual solids termed residue. The residue is composed of various dispersible solid materials and typically contains the resultant radioactivity from the waste. This report describes the immobilization of the residue in portland cement, borosilicate glass, and some other waste forms. Diagrams showing the cement and glass virtification parameters are included in the report as well as process steps and candidate waste product forms. Cement immobilization is simplest and probably least expensive; glass vitrification exhibits the best overall volume reduction ratio

Electrodialytic upgrading of MSWI APC residue from hazardous waste to secondary resource

DEFF Research Database (Denmark)

Jensen, Pernille Erland; Kirkelund, Gunvor Marie; Parés Viader, Raimon

.g. for substitution of cement or fillers in concrete. In general leaching could not be reduced by optimizing current density and treatment time in the pilot scale stack treatment unit, as hypothesized, even though there was evidence of dependency on current density for e.g. zinc, this was not true for most elements......The aim of this project was to contribute to the development of electrodialytic treatment technology of air pollution control residues (APC) from municipal solid waste incineration (MSWI) to obtain maximal leaching reduction by optimization of treatment time and current density for different types...

Waste vinegar residue as substrate for phytase production.

Science.gov (United States)

Wang, Zhi-Hong; Dong, Xiao-Fang; Zhang, Guo-Qing; Tong, Jian-Ming; Zhang, Qi; Xu, Shang-Zhong

2011-12-01

Waste vinegar residue, the by-product of vinegar processing, was used as substrate for phytase production from Aspergillus ficuum NTG-23 in solid-state fermentation to investigate the potential for the efficient re-utilization or recycling of waste vinegar residue. Statistical designs were applied in the processing of phytase production. First, a Plackett-Burman (PB) design was used to evaluate eleven parameters: glucose, starch, wheat bran, (NH(4))(2)SO(4), NH(4)NO(3), tryptone, soybean meal, MgSO(4)·7H(2)O, CaCl(2)·7H(2)O, FeSO(4)·7H(2)O, incubation time. The PB experiments showed that there were three significant factors: glucose, soybean meal and incubation time. The closest values to the optimum point were then derived by steepest ascent path. Finally, a mathematical model was created and validated to explain the behavioural process after these three significant factors were optimized using response surface methodology (RSM). The best phytase activity was attained using the following conditions: glucose (7.2%), soybean meal (5.1%), and incubation time (271 h). The phytase activity was 7.34-fold higher due to optimization by PB design, steepest ascent path design and RSM. The phytase activity was enhanced 0.26-fold in comparison with the results by the second step of steepest ascent path design. The results indicate that with waste vinegar residue as a substrate higher production of phytase from Aspergillus ficuum NTG-23 could be obtained through an optimization process and that this method might be applied to an integrated system for recycling of the waste vinegar residue.

On the ASR and ASR thermal residues characterization of full scale treatment plant.

Science.gov (United States)

Mancini, G; Viotti, P; Luciano, A; Fino, D

2014-02-01

In order to obtain 85% recycling, several procedures on Automotive Shredder Residue (ASR) could be implemented, such as advanced metal and polymer recovery, mechanical recycling, pyrolysis, the direct use of ASR in the cement industry, and/or the direct use of ASR as a secondary raw material. However, many of these recovery options appear to be limited, due to the possible low acceptability of ASR based products on the market. The recovery of bottom ash and slag after an ASR thermal treatment is an option that is not usually considered in most countries (e.g. Italy) due to the excessive amount of contaminants, especially metals. The purpose of this paper is to provide information on the characteristics of ASR and its full-scale incineration residues. Experiments have been carried out, in two different experimental campaigns, in a full-scale tyre incineration plant specifically modified to treat ASR waste. Detailed analysis of ASR samples and combustion residues were carried out and compared with literature data. On the basis of the analytical results, the slag and bottom ash from the combustion process have been classified as non-hazardous wastes, according to the EU waste acceptance criteria (WAC), and therefore after further tests could be used in future in the construction industry. It has also been concluded that ASR bottom ash (EWC - European Waste Catalogue - code 19 01 12) could be landfilled in SNRHW (stabilized non-reactive hazardous waste) cells or used as raw material for road construction, with or without further treatment for the removal of heavy metals. In the case of fly ash from boiler or Air Pollution Control (APC) residues, it has been found that the Cd, Pb and Zn concentrations exceeded regulatory leaching test limits therefore their removal, or a stabilization process, would be essential prior to landfilling the use of these residues as construction material. Copyright © 2013 Elsevier Ltd. All rights reserved.

The use of fly larvae for organic waste treatment.

Science.gov (United States)

Čičková, Helena; Newton, G Larry; Lacy, R Curt; Kozánek, Milan

2015-01-01

The idea of using fly larvae for processing of organic waste was proposed almost 100 years ago. Since then, numerous laboratory studies have shown that several fly species are well suited for biodegradation of organic waste, with the house fly (Musca domestica L.) and the black soldier fly (Hermetia illucens L.) being the most extensively studied insects for this purpose. House fly larvae develop well in manure of animals fed a mixed diet, while black soldier fly larvae accept a greater variety of decaying organic matter. Blow fly and flesh fly maggots are better suited for biodegradation of meat processing waste. The larvae of these insects have been successfully used to reduce mass of animal manure, fecal sludge, municipal waste, food scrapes, restaurant and market waste, as well as plant residues left after oil extraction. Higher yields of larvae are produced on nutrient-rich wastes (meat processing waste, food waste) than on manure or plant residues. Larvae may be used as animal feed or for production of secondary products (biodiesel, biologically active substances). Waste residue becomes valuable fertilizer. During biodegradation the temperature of the substrate rises, pH changes from neutral to alkaline, ammonia release increases, and moisture decreases. Microbial load of some pathogens can be substantially reduced. Both larvae and digested residue may require further treatment to eliminate pathogens. Facilities utilizing natural fly populations, as well as pilot and full-scale plants with laboratory-reared fly populations have been shown to be effective and economically feasible. The major obstacles associated with the production of fly larvae from organic waste on an industrial scale seem to be technological aspects of scaling-up the production capacity, insufficient knowledge of fly biology necessary to produce large amounts of eggs, and current legislation. Technological innovations could greatly improve performance of the biodegradation facilities and

Effects of moisture content of food waste on residue separation, larval growth and larval survival in black soldier fly bioconversion.

Science.gov (United States)

Cheng, Jack Y K; Chiu, Sam L H; Lo, Irene M C

2017-09-01

In order to foster sustainable management of food waste, innovations in food waste valorization technologies are crucial. Black soldier fly (BSF) bioconversion is an emerging technology that can turn food waste into high-protein fish feed through the use of BSF larvae. The conventional method of BSF bioconversion is to feed BSF larvae with food waste directly without any moisture adjustment. However, it was reported that difficulty has been experienced in the separation of the residue (larval excreta and undigested material) from the insect biomass due to excessive moisture. In addition to the residue separation problem, the moisture content of the food waste may also affect the growth and survival aspects of BSF larvae. This study aims to determine the most suitable moisture content of food waste that can improve residue separation as well as evaluate the effects of the moisture content of food waste on larval growth and survival. In this study, pre-consumer and post-consumer food waste with different moisture content (70%, 75% and 80%) was fed to BSF larvae in a temperature-controlled rotary drum reactor. The results show that the residue can be effectively separated from the insect biomass by sieving using a 2.36mm sieve, for both types of food waste at 70% and 75% moisture content. However, sieving of the residue was not feasible for food waste at 80% moisture content. On the other hand, reduced moisture content of food waste was found to slow down larval growth. Hence, there is a trade-off between the sieving efficiency of the residue and the larval growth rate. Furthermore, the larval survival rate was not affected by the moisture content of food waste. A high larval survival rate of at least 95% was achieved using a temperature-controlled rotary drum reactor for all treatment groups. The study provides valuable insights for the waste management industry on understanding the effects of moisture content when employing BSF bioconversion for food waste recycling

New treatment centers for radioactive waste from Russian designed VVER-reactors

International Nuclear Information System (INIS)

Chrubasik, A.

1997-01-01

The nuclear power plants using Russian designed VVER-type reactors, were engineered and designed without any wastes treatment facilities. The liquid and solid waste were collected in storage tanks and shelters. After many years of operation, the storage capabilities are exhausted. The treatment of the stored and still generated waste represents a problem of reactor safety and requires a short term solution. NUKEM has been commissioned to design and construct several new treatment centers to remove and process the stored waste. This paper describes the process and lessons learned on the development of this system. The new radioactive waste treatment center (RWTC) includes comprehensive systems to treat both liquid and solid wastes. The process includes: 1) treatment of evaporator concentrates, 2) treatment of ion exchange resins, 3) treatment of solid burnable waste, 4) treatment of liquid burnable waste, 5) treatment of solid decontaminable waste, 6) treatment of solid compactible waste. To treat these waste streams, various separate systems and facilities are needed. Six major facilities are constructed including: 1. A sorting facility with systems for waste segregation. 2. A high-force compactor facility for volume reduction of non-burnable waste. 3. An incinerator facility for destruction of: 1) solid burnable waste, 2) liquid burnable waste, 3) low level radioactive ion exchange resins. 4. A facility for melting of incineration residue. 5. A cementation facility for stabilization of: 1) medium level radioactive ion exchange resins, 2) solid non compactible waste, 3) compacted solid waste. 6. Separation of radionuclides from evaporator concentrates. This presentation will address the facilities, systems, and lessons learned in the development of the new treatment centers. (author)

The residuals analysis project: Evaluating disposal options for treated mixed low-level waste

International Nuclear Information System (INIS)

Waters, R.D.; Gruebel, M.M.; Case, J.T.; Letourneau, M.J.

1997-01-01

For almost four years, the U.S. Department of Energy (DOE) through its Federal Facility Compliance Act Disposal Workgroup has been working with state regulators and governors' offices to develop an acceptable configuration for disposal of its mixed low-level waste (MLLW). These interactions have resulted in screening the universe of potential disposal sites from 49 to 15 and conducting ''performance evaluations'' for those fifteen sites to estimate their technical capabilities for disposal of MLLW. In the residuals analysis project, we estimated the volume of DOE's MLLW that will require disposal after treatment and the concentrations of radionuclides in the treated waste. We then compared the radionuclide concentrations with the disposal limits determined in the performance evaluation project for each of the fifteen sites. The results are a scoping-level estimate of the required volumetric capacity for MLLW disposal and the identification of waste streams that may pose problems for disposal based on current treatment plans. The analysis provides technical information for continued discussions between the DOE and affected States about disposal of MLLW and systematic input to waste treatment developers on disposal issues

Shielding evaluation of the Thorium Lean Raffinate (TLR) waste treatment system at Waste Immobilisation Plant, Trombay

International Nuclear Information System (INIS)

Bhosale, Nitin A.; Deepa, A.K.; Jakhete, A.P.; Gopalakrishnan, R.K.; Prasad, S.K.; Gangadharan, Anand; Singh, Neelima

2012-01-01

Thoria rods irradiated in research reactors were reprocessed for 233 U recovery and resulted in 9 m 3 of acidic Th-bearing raffinate waste. A two step treatment system was planned to treat the raffinate waste. The first step was the generation of thorium lean raffinate waste (TLR) after separation of thorium and the second step was the separation of residual radioactivity and conditioning planned at WIP. The beta activity in the TLR waste is around 50 mCi/i having 137 Cs, 90 Sr and 125 Sb as its main constituents. Shielding calculations were carried out for the various stages of the treatment system at Area-61 of WIP, Trombay. Dose rate evaluations at each step of the treatment system were evaluated to keep the personnel exposure during campaign, ALARA. The work set the base for the shielding design of the treatment system and for the estimation of the man-rem budgeting during commissioning of the system

Modification of bauxite residue generated in the Bayer process by thermal treatment

International Nuclear Information System (INIS)

Garcia, M.C.S.; Pileggi, R.G.; John, V.M.; Gouvea, D.

2011-01-01

Red mud is the waste generated by the aluminum industry, and as other industrial waste presents complex characteristics with numerous difficulties in handling, as well as being a hazardous material due to its low granulometry, alkalinity and high amount generated. It is a waste with potential high polluter, aggravated by the generally adopted vulnerable disposal form, being this, the disposition of the residue in ponds designed for this purpose. The study and development of sustainable alternatives for the use of sludge, treated as raw materials from other processes, are important tendency and necessary trends in the global context of environmental preservation. This work deals with the thermal treatment as a method of modification of the characteristics of the residue, suggesting the reduction of alkalinity together with the lower leaching of alkaline ions. This approach can be a more reliable and environmentally safe disposal alternatives

Effects of hydrated lime on radionuclides stabilization of Hanford tank residual waste.

Science.gov (United States)

Wang, Guohui; Um, Wooyong; Cantrell, Kirk J; Snyder, Michelle M V; Bowden, Mark E; Triplett, Mark B; Buck, Edgar C

2017-10-01

Chemical stabilization of tank residual waste is part of a Hanford Site tank closure strategy to reduce overall risk levels to human health and the environment. In this study, a set of column leaching experiments using tank C-104 residual waste were conducted to evaluate the leachability of uranium (U) and technetium (Tc) where grout and hydrated lime were applied as chemical stabilizing agents. The experiments were designed to simulate future scenarios where meteoric water infiltrates through the vadose zones into the interior of the tank filled with layers of grout or hydrated lime, and then contacts the residual waste. Effluent concentrations of U and Tc were monitored and compared among three different packing columns (waste only, waste + grout, and waste + grout + hydrated lime). Geochemical modeling of the effluent compositions was conducted to determine saturation indices of uranium solid phases that could control the solubility of uranium. The results indicate that addition of hydrated lime strongly stabilized the uranium through transforming uranium to a highly insoluble calcium uranate (CaUO 4 ) or similar phase, whereas no significant stabilization effect of grout or hydrated lime was observed on Tc leachability. The result implies that hydrated lime could be a great candidate for stabilizing Hanford tank residual wastes where uranium is one of the main concerns. Published by Elsevier Ltd.

Molten salt treatment to minimize and optimize waste

International Nuclear Information System (INIS)

Gat, U.; Crosley, S.M.; Gay, R.L.

1993-01-01

A combination molten salt oxidizer (MSO) and molten salt reactor (MSR) is described for treatment of waste. The MSO is proposed for contained oxidization of organic hazardous waste, for reduction of mass and volume of dilute waste by evaporation of the water. The NTSO residue is to be treated to optimize the waste in terms of its composition, chemical form, mixture, concentration, encapsulation, shape, size, and configuration. Accumulations and storage are minimized, shipments are sized for low risk. Actinides, fissile material, and long-lived isotopes are separated and completely burned or transmuted in an MSR. The MSR requires no fuel element fabrication, accepts the materials as salts in arbitrarily small quantities enhancing safety, security, and overall acceptability

Economic and environmental optimization of waste treatment

Energy Technology Data Exchange (ETDEWEB)

Münster, M. [System Analysis Department, DTU Management Engineering, Technical University of Denmark, Frederiksborgvej 399, 4000 Roskilde (Denmark); Ravn, H. [RAM-løse edb, Æblevangen 55, 2765 Smørum (Denmark); Hedegaard, K.; Juul, N. [System Analysis Department, DTU Management Engineering, Technical University of Denmark, Frederiksborgvej 399, 4000 Roskilde (Denmark); Ljunggren Söderman, M. [IVL Swedish Environmental Research Institute, Box 53021, SE-40014 Gothenburg (Sweden); Chalmers University of Technology, SE-412 96 Gothenburg (Sweden)

2015-04-15

Highlights: • Optimizing waste treatment by incorporating LCA methodology. • Applying different objectives (minimizing costs or GHG emissions). • Prioritizing multiple objectives given different weights. • Optimum depends on objective and assumed displaced electricity production. - Abstract: This article presents the new systems engineering optimization model, OptiWaste, which incorporates a life cycle assessment (LCA) methodology and captures important characteristics of waste management systems. As part of the optimization, the model identifies the most attractive waste management options. The model renders it possible to apply different optimization objectives such as minimizing costs or greenhouse gas emissions or to prioritize several objectives given different weights. A simple illustrative case is analysed, covering alternative treatments of one tonne of residual household waste: incineration of the full amount or sorting out organic waste for biogas production for either combined heat and power generation or as fuel in vehicles. The case study illustrates that the optimal solution depends on the objective and assumptions regarding the background system – illustrated with different assumptions regarding displaced electricity production. The article shows that it is feasible to combine LCA methodology with optimization. Furthermore, it highlights the need for including the integrated waste and energy system into the model.

Life-cycle assessment of selected management options for air pollution control residues from waste incineration.

Science.gov (United States)

Fruergaard, Thilde; Hyks, Jiri; Astrup, Thomas

2010-09-15

Based on available technology and emission data seven selected management options for air-pollution-control (APC) residues from waste incineration were evaluated by life-cycle assessment (LCA) using the EASEWASTE model. Scenarios were evaluated with respect to both non-toxicity impact categories (e.g. global warming) and toxicity related impact categories (e.g. ecotoxicity and human toxicity). The assessment addressed treatment and final placement of 1 tonne of APC residue in seven scenarios: 1) direct landfilling without treatment (baseline), 2) backfilling in salt mines, 3) neutralization of waste acid, 4) filler material in asphalt, 5) Ferrox stabilization, 6) vitrification, and 7) melting with automobile shredder residues (ASR). The management scenarios were selected as examples of the wide range of different technologies available worldwide while at the same time using realistic technology data. Results from the LCA were discussed with respect to importance of: energy consumption/substitution, material substitution, leaching, air emissions, time horizon aspects for the assessment, and transportation distances. The LCA modeling showed that thermal processes were associated with the highest loads in the non-toxicity categories (energy consumption), while differences between the remaining alternatives were small and generally considered insignificant. In the toxicity categories, all treatment/utilization options were significantly better than direct landfilling without treatment (lower leaching), although the thermal processes had somewhat higher impacts than the others options (air emissions). Transportation distances did not affect the overall ranking of the management alternatives. Copyright 2010 Elsevier B.V. All rights reserved.

Innovative systems for mixed waste retrieval and/or treatment in confined spaces

International Nuclear Information System (INIS)

Fekete, L.J.; Ghusn, A.E.

1993-03-01

Fernald established operations in 1951 and produced uranium and other metals for use at other DOE facilities. A part of the sitewide remediation effort is the removal, treatment, and disposal of the K-65 wastes from Silos 1 and 2. These silos contain radium-bearing residues from the processing of pitchblende ore. An Engineering Evaluation/Cost Analysis was prepared to evaluate the removal action alternatives using the preliminary characterization data and select a preferred alternative. The selected alternative consisted of covering the K-65 residues and the silo dome. The remediation of the K-65 wastes consists of the retrieval and treatment of the wastes prior to final disposal, which has not yet been determined. Treatment will be performed in a new facility to be built adjacent to the silos. The wastes must be retrieved from silos in an efficient and reliable way and delivered to the treatment facility. The first challenge of covering the wastes with bentonite has been successfully met. The second phase of retrieving the wastes from the silos is not due for a few years. However, conceptual design and configuration of the retrieval system have been developed as part of the Conceptual Design Report. The system is based on the utilization of hydraulic mining techniques, and is based on similar successful applications. This report describes the emplacement of the bentonite grant and the design for the slurry retrieval system

AERE contracts with DOE on the treatment and disposal of Intermediate Level Wastes

International Nuclear Information System (INIS)

Partridge, B.A.

1985-07-01

Individual summaries are provided for each contract report, under the titles: comparative evaluation of α and βγ irradiated medium level waste forms; modelling and characterisation of intermediate level waste forms based on polymers; optimisation of processing parameters for polymer and bitumen modified cements; α damage in non-reference matrix materials; leaching mechanisms and modelling; inorganic ion exchange treatment of medium active effluents; electrical processes for the treatment of medium active liquid waste; fast reactor fuel element cladding; dissolver residues; effects of radiation on the properties of cemented MTR waste forms; equilibrium leach testing of cemented MTR waste forms; radiolytic oxidation of radionuclides; immobilisation of liquid organic wastes; quality control, non-conformances and corrective action; application of gel processes in the treatment of actinide-containing liquid wastes; the role of colloids in the release of radionuclides from nuclear waste. (author)

Preliminary analysis of treatment strategies for transuranic wastes from reprocessing plants

International Nuclear Information System (INIS)

Ross, W.A.; Schneider, K.J.; Swanson, J.L.; Yasutake, K.M.; Allen, R.P.

1985-07-01

This document provides a comparison of six treatment options for transuranic wastes (TRUW) resulting from the reprocessing of commercial spent fuel. Projected transuranic waste streams from the Barnwell Nuclear Fuel Plant (BNFP), the reference fuel reprocessing plant in this report, were grouped into the five categories of hulls and hardware, failed equipment, filters, fluorinator solids, and general process trash (GPT) and sample and analytical cell (SAC) wastes. Six potential treatment options were selected for the five categories of waste. These options represent six basic treatment objectives: (1) no treatment, (2) minimum treatment (compaction), (3) minimum number of processes and products (cementing or grouting), (4) maximum volume reduction without decontamination (melting, incinerating, hot pressing), (5) maximum volume reduction with decontamination (decontamination, treatment of residues), and (6) noncombustible waste forms (melting, incinerating, cementing). Schemes for treatment of each waste type were selected and developed for each treatment option and each type of waste. From these schemes, transuranic waste volumes were found to vary from 1 m 3 /MTU for no treatment to as low as 0.02 m 3 /MTU. Based on conceptual design requirements, life-cycle costs were estimated for treatment plus on-site storage, transportation, and disposal of both high-level and transuranic wastes (and incremental low-level wastes) from 70,000 MTU. The study concludes that extensive treatment is warranted from both cost and waste form characteristics considerations, and that the characteristics of most of the processing systems used are acceptable. The study recommends that additional combinations of treatment methods or strategies be evaluated and that in the interim, melting, incineration, and cementing be further developed for commercial TRUW. 45 refs., 9 figs., 32 tabs

Preliminary analysis of treatment strategies for transuranic wastes from reprocessing plants

Energy Technology Data Exchange (ETDEWEB)

Ross, W.A.; Schneider, K.J.; Swanson, J.L.; Yasutake, K.M.; Allen, R.P.

1985-07-01

This document provides a comparison of six treatment options for transuranic wastes (TRUW) resulting from the reprocessing of commercial spent fuel. Projected transuranic waste streams from the Barnwell Nuclear Fuel Plant (BNFP), the reference fuel reprocessing plant in this report, were grouped into the five categories of hulls and hardware, failed equipment, filters, fluorinator solids, and general process trash (GPT) and sample and analytical cell (SAC) wastes. Six potential treatment options were selected for the five categories of waste. These options represent six basic treatment objectives: (1) no treatment, (2) minimum treatment (compaction), (3) minimum number of processes and products (cementing or grouting), (4) maximum volume reduction without decontamination (melting, incinerating, hot pressing), (5) maximum volume reduction with decontamination (decontamination, treatment of residues), and (6) noncombustible waste forms (melting, incinerating, cementing). Schemes for treatment of each waste type were selected and developed for each treatment option and each type of waste. From these schemes, transuranic waste volumes were found to vary from 1 m/sup 3//MTU for no treatment to as low as 0.02 m/sup 3//MTU. Based on conceptual design requirements, life-cycle costs were estimated for treatment plus on-site storage, transportation, and disposal of both high-level and transuranic wastes (and incremental low-level wastes) from 70,000 MTU. The study concludes that extensive treatment is warranted from both cost and waste form characteristics considerations, and that the characteristics of most of the processing systems used are acceptable. The study recommends that additional combinations of treatment methods or strategies be evaluated and that in the interim, melting, incineration, and cementing be further developed for commercial TRUW. 45 refs., 9 figs., 32 tabs.

Glass-Ceramic Waste Forms for Uranium and Plutonium Residues Wastes - 13164

International Nuclear Information System (INIS)

Stewart, Martin W.A.; Moricca, Sam A.; Zhang, Yingjie; Day, R. Arthur; Begg, Bruce D.; Scales, Charlie R.; Maddrell, Ewan R.; Hobbs, Jeff

2013-01-01

A program of work has been undertaken to treat plutonium-residues wastes at Sellafield. These have arisen from past fuel development work and are highly variable in both physical and chemical composition. The principal radiological elements present are U and Pu, with small amounts of Th. The waste packages contain Pu in amounts that are too low to be economically recycled as fuel and too high to be disposed of as lower level Pu contaminated material. NNL and ANSTO have developed full-ceramic and glass-ceramic waste forms in which hot-isostatic pressing is used as the consolidation step to safely immobilize the waste into a form suitable for long-term disposition. We discuss development work on the glass-ceramic developed for impure waste streams, in particular the effect of variations in the waste feed chemistry glass-ceramic. The waste chemistry was categorized into actinides, impurity cations, glass formers and anions. Variations of the relative amounts of these on the properties and chemistry of the waste form were investigated and the waste form was found to be largely unaffected by these changes. This work mainly discusses the initial trials with Th and U. Later trials with larger variations and work with Pu-doped samples further confirmed the flexibility of the glass-ceramic. (authors)

AERE contracts with DoE on the treatment and disposal of intermediate level wastes

International Nuclear Information System (INIS)

Partridge, B.A.

1984-11-01

Reports are presented on work on the following topics concerned with the treatment and disposal of intermediate-level radioactive wastes: comparative evaluation of α and β γ irradiated medium level waste forms; modelling and characterisation of intermediate level waste forms based on polymers; optimisation of processing parameters for polymer and bitumen modified cements; α damage in non-reference waste form matrix materials; leaching mechanisms and modelling; inorganic ion exchange treatment of medium active effluents; electrical processes for the treatment of medium active liquid waste; fast reactor fuel element cladding; dissolver residues; effects of radiation on the properties of cemented MTR waste forms; equilibrium leach testing of cemented MTR waste forms; radiolytic oxidation of radionuclides; immobilisation of liquid organic waste; quality control, non-conformances and corrective action. (U.K.)

Combining physico-chemical analysis with a Daphnia magna bioassay to evaluate a recycling technology for drinking water treatment plant waste residuals.

Science.gov (United States)

Chen, Ting; Xu, Yongpeng; Zhu, Shijun; Cui, Fuyi

2015-12-01

Recycling water treatment plant (WTP) waste residuals is considered to be a feasible method to enhance the efficiency of pollutant removal. This study also evaluated the safety and water quality of a pilot-DWTP waste residuals recycling technology by combining physical-chemistry analysis with a Daphnia magna assay. The water samples taken from each treatment step were extracted and concentrated by XAD-2 resin and were then analyzed for immobilization and enzyme activity with D. magna. The measured parameters, such as the dissolve organic carbon (DOC), UV254 and THM formation potential (THMFPs) of the recycling process, did not obviously increase over 15 days of continuous operation and were even lower than typical values from a conventional process. The extract concentration ranged from 0 to 2 Leq/ml as measured on the 7th and 15th days and the immobilization of D. magna exposed to water treated by the recycling process was nearly equivalent to that of the conventional process. Both the superoxide dismutase (SOD) and the catalase (CAT) activity assay indicated that a lower dose of water extract (0.5, 1, 1.5 Leq/ml) could stimulate the enzyme activity of D. magna, whereas a higher dose (2 Leq/ml at the sampling point C3, R3, R4 ) inhibits the activity. Moreover, the SOD and CAT activity of D. magna with DOC and UV254 showed a strong concentration-effect relationship, where the concentration range of DOC and UV254 were 4.1-16.2 mg/L and 0.071-4.382 cm(-1), respectively. The results showed that there was no statistically significant difference (p>0.05) between the conventional and recycling treatment processes and the toxicity of water samples in the recycling process did not increase during the 15-day continuous recycling trial. Copyright © 2015 Elsevier Inc. All rights reserved.

Contaminant transport at a waste residue deposit

DEFF Research Database (Denmark)

Engesgaard, Peter Knudegaard; Traberg, Rikke

1996-01-01

Contaminant transport in an aquifer at an incinerator waste residue deposit in Denmark is simulated. A two-dimensional, geochemical transport code is developed for this purpose and tested by comparison to results from another code, The code is applied to a column experiment and to the field site...

Solid residues from Italian municipal solid waste incinerators: A source for "critical" raw materials.

Science.gov (United States)

Funari, Valerio; Braga, Roberto; Bokhari, Syed Nadeem Hussain; Dinelli, Enrico; Meisel, Thomas

2015-11-01

The incineration of municipal solid wastes is an important part of the waste management system along with recycling and waste disposal, and the solid residues produced after the thermal process have received attention for environmental concerns and the recovery of valuable metals. This study focuses on the Critical Raw Materials (CRM) content in solid residues from two Italian municipal waste incinerator (MSWI) plants. We sampled untreated bottom ash and fly ash residues, i.e. the two main outputs of common grate-furnace incinerators, and determined their total elemental composition with sensitive analytical techniques such as XRF and ICP-MS. After the removal of a few coarse metallic objects from bottom ashes, the corresponding ICP solutions were obtained using strong digestion methods, to ensure the dissolution of the most refractory components that could host significant amounts of precious metals and CRM. The integration of accurate chemical data with a substance flow analysis, which takes into account the mass balance and uncertainties assessment, indicates that bottom and fly ashes can be considered as a low concentration stream of precious and high-tech metals. The magnesium, copper, antimony and zinc contents are close to the corresponding values of a low-grade ore. The distribution of the elements flow between bottom and fly ash, and within different grain size fractions of bottom ash, is appraised. Most elements are enriched in the bottom ash flow, especially in the fine grained fractions. However, the calculated transfer coefficients indicate that Sb and Zn strongly partition into the fly ashes. The comparison with available studies indicates that the CRM concentrations in the untreated solid residues are comparable with those residues that undergo post-treatment beneficiations, e.g. separation between ferrous and non-ferrous fractions. The suggested separate collection of "fresh" bottom ash, which could be processed for further mineral upgrading, can

[Waste over history: perceptions about residues].

Science.gov (United States)

Velloso, Marta Pimenta

2008-01-01

This article describes how Man, over history, felt about the residues produced by human activity. The text is divided into three parts: In the first part it tells the story of the black plague pandemic during the XIV century, showing how this disease was associated with the residues produced by the human body. In the second part it explains how the first notions of waste were, and still are, related to dirt, disease and death. Finally, in the third part, it describes the first measures of hygiene in the Renaissance and refers to the first public health actions at the beginning of the XX century, starting to combat the agents of infectious diseases and their vectors.

Waste Water Treatment And Data Book Of Method Of Water Quality Analysis

International Nuclear Information System (INIS)

1999-03-01

This book indicates the method of water quality analysis and waste water treatment with collecting water quality data of advanced country and WHO, which introduces poisonous substance in industrial waste water such as heavy metal, ammonia, chlorine ion, PCB, chloroform, residual chlorine and manganese, reports about influence of those materials on human health, lists on method of analysis the poisonous substance, research way like working order and precautions on treatment and method of chemical process and use.

Comparative environmental evaluation of three different waste treating methods for bio-degradable organic waste and residual waste from the six municipalities cooperating in Biogasanlaeg I/S and I/S Nordforbraending

International Nuclear Information System (INIS)

Cour Jansen, J. la.

1997-03-01

A comparative environmental evaluation has been made for three systems for processing household refuse. The first system (1) comprises thermofilic treatment of the organic waste. The inorganic parts of the waste from both systems is combusted in a cogeneration plant. The third system (3) is a cogeneration plant combusting all the wastes. The most essential issue in comparing the three waste processing systems is the possibility to use the residual products from the bio-gasification system (1) and the composting system in the agriculture as fertilizers. Without such a use it is estimated that the systems (1) and (2) will be very unfeasible, both environmentally and economically. The contents of heavy metals, organic chemicals, and plasticizers in the residual products are at present above the Danish threshold values. This problem can only be solved by reducing the contents of these pollutants in the household wastes. Based on these findings it is therefore very doubtful whether the residual waste products from bio-gasification and probably also from composting can be used in the agriculture in the future. However, it is for the other parts of the environmental analysis assumed that the problem will eventually be solved. Differences in resource utilization in the waste processing are very small in the three systems. When comparing the net energy production system (1) and (3) show the best results. The three systems are almost equal related to emissions of HC1, NO x , and SO 2 , the composting system performing the best. The three systems emit the same amount of CO 2 and other greenhouse gases. Composting, however, results in a smaller energy susbstituion and is therefore marginally a poorer solution. For reducing the heavy metals and plasticizers in the environment combustion of the organic wastes is the best system. (LN)

Effects of inoculum source and co-digestion strategies on anaerobic digestion of residues generated in the treatment of waste vegetable oils.

Science.gov (United States)

Hidalgo, Dolores; Martín-Marroquín, Jesús M

2014-09-01

This work aims at selecting a suitable strategy to improve the performance of the anaerobic digestion of residues generated in the treatment of waste vegetable oils (WVO). Biochemical methane potential (BMP) assays were conducted at 35 °C to evaluate the effects of substrate mix ratio between a mixture of WVO residues (M) and pig manure (PM) co-digesting by using different inocula. Inoculum from an industrial digester fed with organic waste from hotels, restaurants and catering leftovers (HORECA) showed higher methanogenic activity (55.5 mLCH4 gVS(-1) d(-1)) than municipal wastewater treatment plant (mWWTP) inoculum (42.6 mL CH4 gVS(-1) d(-1)). Furthermore, the results showed that the resistance to WVO residues toxicity was higher for the HORECA sludge than for the mWWTP sludge. HORECA inoculum produced more biogas in all the assays. Moreover, the resulting biogas was of better quality, containing an average of 71.1% (SD = 1.6) methane compared to an average of 69.5% (SD = 1.2) methane for test with mWWTP sludge. The maximum degradation rate occurred at the higher PM mix ratio (M/PM:1/3), reaching 26.7 ± 4.3 mLCH4 gVS(-1) d(-1) for mWWTP inoculum, versus 42.0 ± 1,5 mLCH4 gVS(-1) d(-1) achieved for HORECA inoculum. A high reduction of volatile solids (between 70% and 81%) was obtained with both inocula at all M/PM ratios assayed (1/0, 1/3, 1/1 and 3/1 v/v) but, bearing in mind the operation of a full-scale anaerobic plant, the optimal scenario assayed corresponds to the ratio M/PM: 1/3 v/v where shorter lag periods will make it possible to operate at lower hydraulic retention times. Copyright © 2014 Elsevier Ltd. All rights reserved.

Role of disposal in developing Federal Facility Compliance Act mixed waste treatment plans

International Nuclear Information System (INIS)

Case, J.T.; Rhoderick, J.

1994-01-01

The Federal Facilities Compliance Act (FFCA) was enacted on October 6, 1992. This act amends the Solid Waste Disposal Act, which was previously amended by the Resource Conservation and Recovery Act (RCRA). The FFCA set in place a process for managing the Department of Energy's (DOE) mixed low-level radioactive wastes (MLLW), wastes that contain both hazardous and low-level radioactive constituents, with full participation of the affected states. The FFCA provides the framework for the development of treatment capacity for DOE's mixed waste. Disposal of the treatment residues is not addressed by the FFCA. DOE has initiated efforts in concert with the states in the development of a disposal strategy for the treated mixed wastes. This paper outlines DOE efforts in development of a mixed waste disposal strategy which is integrated with the FFCA Site Treatment Planning process

Effect of drying on leaching testing of treated municipal solid waste incineration APC-residues

DEFF Research Database (Denmark)

Hu, Y.; Hyks, Jiri; Astrup, Thomas

2008-01-01

Air-pollution-control (APC) residues from waste incinerators are hazardous waste according to European legislation and must be treated prior to landfilling. Batch and column leaching data determine which type of landfill can receive the treated APC-residues. CEN standards are prescribed...

Characterization on incineration residue of radioactive solid wastes

International Nuclear Information System (INIS)

Katoh, Kiyoshi; Hirayama, Katsuyoshi; Kato, Akira.

1989-01-01

Characterization was carried out on incineration residue discharged from the radioactive solid waste incineration unit (capacity, 100 kg/h) in use at the Tokai Research Establishment of Japan Atomic Energy Research Institute (JAERI) to obtain basic data for investigating solidification methods of the residue. The characterized residue was taken from furnace and a primary ceramic filter of the incineration unit which incinerates combustible solid wastes generated at JAERI and the outside organizations. Items of characterization involve a particle size distribution, misplaced materials content, ignition loss, chemical composition and radioactivity of nuclides in the ash. As the results, the size of ash sampled from the furnace distributed a wide range, with about 35∼60 % of ash smaller than 5 mm and about 10∼25 % of massive one larger than 30 mm (max. size: ∼130 mm). The ignition loss was 2∼3 %. The chemical compositions of the ash were mainly SiO 2 , Fe 2 O 3 , CaO and Al 2 O 3 . The specific activities of the ash were about 0.4∼4 x 10 3 Bq/g, and principal contaminants were 60 Co and 137 Cs. (author)

Contaminant Release from Residual Waste in Single Shell Tanks at the Hanford Site, Washington, USA - 9276

International Nuclear Information System (INIS)

Cantrell, Kirk J.; Krupka, Kenneth M.; Deutsch, William J.; Lindberg, Michael J.

2009-01-01

Determinations of elemental and solid-phase compositions, and contaminant release studies have been applied in an ongoing study of residual tank wastes (i.e., waste remaining after final retrieval operations) from five of 149 underground single-shell storage tanks (241-C-103, 241-C-106, 241-C-202, 241-C-203, and 241-S-112) at the U.S. Department of Energy's Hanford Site in Washington State. This work is being conducted to support performance assessments that will be required to evaluate long-term health and safety risks associated with tank site closure. The results of studies completed to date show significant variability in the compositions, solid phase properties, and contaminant release characteristics from these residual tank wastes. This variability is the result of differences in waste chemistry/composition of wastes produced from several different spent fuel reprocessing schemes, subsequent waste reprocessing to remove certain target constituents, tank farm operations that concentrated wastes and mixed wastes between tanks, and differences in retrieval processes used to remove the wastes from the tanks. Release models were developed based upon results of chemical characterization of the bulk residual waste, solid-phase characterization (see companion paper 9277 by Krupka et al.), leaching and extraction experiments, and geochemical modeling. In most cases empirical release models were required to describe contaminant release from these wastes. Release of contaminants from residual waste was frequently found to be controlled by the solubility of phases that could not be identified and/or for which thermodynamic data and/or dissolution rates have not been measured. For example, significant fractions of Tc-99, I-129, and Cr appear to be coprecipitated at trace concentrations in metal oxide phases that could not be identified unambiguously. In the case of U release from tank 241-C-103 residual waste, geochemical calculations indicated that leachate

AERE contracts with DoE on the treatment and disposal of intermediate level wastes

International Nuclear Information System (INIS)

Partridge, B.A.

1984-06-01

This document reports work carried out in 1983/84 under 10 contracts between DoE and AERE on the treatment and disposal of intermediate level wastes. Individual summaries are provided for each contract report within the document, under the headings: comparative evaluation of α and βγ irradiated medium level waste forms; modelling and characterisation of intermediate level waste forms based on polymers; optimisation of processing parameters for polymer and bitumen modified cements; ceramic waste forms; radionuclide release during leaching; ion exchange processes; electrical processes for the treatment of medium active liquid wastes; fast reactor fuel element cladding; dissolver residues; flowsheeting/systems study. (U.K.)

Valorisation of food residues: waste to wealth using green chemical technologies

OpenAIRE

Clark, James H.; Luque, Rafael

2013-01-01

Waste valorisation practises have attracted a significant amount of attention in recent years with the aim of managing waste in the most sustainable way. Food waste constitutes a largely under-exploited residue from which a variety of valuable chemicals can be derived. This contribution is aimed to set the scene for a further development and promotion of sustainable food waste valorisation practises to different end products using green chemical technologies

Quantification of heavy metals from residual waste and ashes from the treatment plant of residual water Reciclagua and,effects for the health of those workers which manipulate those residuals

International Nuclear Information System (INIS)

Guerrero D, J.J.

2004-01-01

In this work, the technique of leaching using thermostatted column in series is applied, the X-ray diffraction for the identification of the atomic and molecular structure of the toxic metals that are present in the residual muds of the water treatment plant located in the municipality of Lerma Estado de Mexico, named RECICLAGUA, likewise the technique is used of emission spectrometry for plasma and X-ray fluorescence for the qualitative analysis. Its were take samples of residual mud and of incinerated mud of the treatment plant of residual waters of the industrial corridor Toluca -Lerma RECICLAGUA, located in Lerma Estado de Mexico. For this study there were mixed 100 g of residual mud with a solution to 10% of mineral acid or sodium hydroxide according to the case, to adjust the one pH at 2, 5, 7 and 10, it was added bisulfite, of 0.3-1.5 g of dodecyl sulfate sodium and 3.939 of DTPA (triple V) (Diethylene triamine pentaacetate). To this mud and ashes were extracted the toxic and valuable metals by means of the leaching technique using thermostatted columns placed in series that were designed by the Dr. Jaime Vite Torres; it is necessary to make mention that so much the process as the equipment with those that work it was patented by the same one. With the extraction of these metals benefits are obtained, mainly of economic type, achieving the decrease of the volume of those wastes that have been generated; as well as the so much the use of those residuals, once the metals have been eliminated, as of those liquors where the metals were extracted. It was carried out a quantitative analysis using emission spectrometry by plasma in solids by this way to be able to know the content of the present metals in the sample before and later of leaching them, these results reported a great quantity of elements. Another of the techniques employees was the X-ray diffraction analysis that provides an elementary content of the samples, identifying elements that are present in

Treatment of low-and intermediate-level radioactive waste concentrates

International Nuclear Information System (INIS)

1968-01-01

The report of a panel convened by the IAEA in Vienna, 2-6 May 1966. Thirteen experts from eight countries and one international organization attended the meeting. This report is related to treatment and radioactive sludges or residues resulting from treatment and purification of radioactive wastes. It includes: (i) concentration by evaporation; (ii) filtration; (iii) insolubilization by means of bitumen; (iv) use of cement or cement-vermiculite. 31 refs, 34 figs, 14 tabs

Flexible process options for the immobilisation of residues and wastes containing plutonium

International Nuclear Information System (INIS)

Stewart, M.W.A.; Moricca, S.A.; Day, R. A.; Begg, B. D.; Scales, C. R.; Maddrell, E. R.; Eilbeck, A. B.

2007-01-01

Residues and waste streams containing plutonium present unique technical, safety, regulatory, security, and socio-political challenges. In the UK these streams range from lightly plutonium contaminated materials (PCM) through to residue s resulting directly from Pu processing operations. In addition there are potentially stocks of Pu oxide powders whose future designation may be either a waste or an asset, due to their levels of contamination making their reuse uneconomic, or to changes in nuclear policy. While waste management routes exist for PCM, an immobilisation process is required for streams containing higher levels of Pu. Such a process is being developed by Nexia Solutions and ANSTO to treat and immobilise Pu waste and residues currently stored on the Sellafield site. The characteristics of these Pu waste streams are highly variable. The physical form of the Pu waste ranges from liquids, sludges, powders/granules, to solid components (e.g., test fuels), with the Pu present as an ion in solution, as a salt, metal, oxide or other compound. The chemistry of the Pu waste streams also varies considerably with a variety of impurities present in many waste streams. Furthermore, with fissile isotopes present, criticality is an issue during operations and in the store or repository. Safeguards and security concerns must be assessed and controlled. The process under development, by using a combination of tailored waste form chemistry combined with flexible process technology aims to develop a process line to handle a broad range of Pu waste streams. It aims to be capable of dealing with not only current arisings but those anticipated to arise as a result of future operations or policy changes. (authors)

How to minimize wastes

International Nuclear Information System (INIS)

Ambolet, M.

1988-10-01

Actions undertaken by the CEA to decrease the stock of natural and depleted uranium are presented in this paper. Various wastes and residues are produced in uranium fabrication. If for some wastes or residues processing methods were found previously, for other storage was the rule. Facing growing problems of safety, bulkiness, and cost new treatments allow to decrease a great amount of wastes. Uranium fabrication cycle, wastes and residues are described. Processing of the different residues of operations and optimization of manufacture are indicated [fr

Life-cycle assessment of a waste refinery process for enzymatic treatment of municipal solid waste

DEFF Research Database (Denmark)

Tonini, Davide; Astrup, Thomas

2012-01-01

for the enzymatic treatment of municipal solid waste (MSW) is presented. The refinery produced a liquid (liquefied organic materials and paper) and a solid fraction (non-degradable materials) from the initial waste. A number of scenarios for the energy utilization of the two outputs were assessed. Co......Decrease of fossil fuel dependence and resource saving has become increasingly important in recent years. From this perspective, higher recycling rates for valuable materials (e.g. metals) as well as energy recovery from waste streams could play a significant role substituting for virgin material...... production and saving fossil resources. This is especially important with respect to residual waste (i.e. the remains after source-separation and separate collection) which in Denmark is typically incinerated. In this paper, a life-cycle assessment and energy balance of a pilot-scale waste refinery...

Radioactive sodium waste treatment and conditioning. Review of main aspects

International Nuclear Information System (INIS)

2007-01-01

This publication reviews the main aspects relating to the treatment and conditioning of radioactive sodium waste. This waste arises from the operation of liquid metal fast reactors (LMFRs). In this type of reactor, sodium (Na) or sodium-potassium alloys (NaK) are used as a low-effect neutron moderating coolant medium for extracting and transferring thermal energy from the core and they represent a significant technical and safety challenge during operation and decommissioning. This publication provides the reader with technologically oriented information on the present status of sodium waste management approaches and recent achievements related to treatment and conditioning, with the objective of facilitating planning and preparatory work for the decommissioning of LMFRs. This publication provides a comprehensive review of the hazards associated with sodium waste management. Given the large quantities of sodium waste arising during decommissioning or reactor refurbishment, as well as the challenges and varied techniques associated with removal of 100% of all sodium and NaK bulk quantities and residues during decommissioning, a hazards review and analysis is a critical component in planning the dismantling and waste management activities. Roughly half of this publication focuses on sodium waste generating, handling and treatment processes. This includes draining sodium and NaK from plant systems; in situ treatment of residual sodium; cutting techniques for pumps, valves, piping and other components; cleaning of components; potential reuse of sodium; and removal of selected radionuclides from sodium waste with the objective of reducing the waste classification or converting it to exempt waste. The focus is on proven techniques and technologies, and each discussed method includes a review of the associated principle or theory, practical applications, advantages and disadvantages, limitations, industry experience, and final waste products. A review is provided of final

Treatment of alumina refinery waste (red mud) through neutralization techniques: A review.

Science.gov (United States)

Rai, Suchita; Wasewar, K L; Agnihotri, A

2017-06-01

In the Bayer process of extraction of alumina from bauxite, the insoluble product generated after bauxite digestion with sodium hydroxide at elevated temperature and pressure is known as 'red mud' or 'bauxite residue'. This alumina refinery waste is highly alkaline in nature with a pH of 10.5-12.5 and is conventionally disposed of in mostly clay-lined land-based impoundments. The alkaline constituents in the red mud impose severe and alarming environmental problems, such as soil and air pollution. Keeping in view sustainable re-vegetation and residue management, neutralization/treatment of red mud using different techniques is the only alternative to make the bauxite residue environmentally benign. Hence, neutralization techniques, such as using mineral acids, acidic waste (pickling liquor waste), coal dust, superphosphate and gypsum as amenders, CO 2 , sintering with silicate material and seawater for treatment of red mud have been studied in detail. This paper is based upon and emphasizes the experimental work carried out for all the neutralization techniques along with a comprehensive review of each of the processes. The scope, applicability, limitations and feasibility of these processes have been compared exhaustively. Merits and demerits have been discussed using flow diagrams. All the techniques described are technically feasible, wherein findings obtained with seawater neutralization can be set as a benchmark for future work. Further studies should be focused on exploring the economical viability of these processes for better waste management and disposal of red mud.

Characterization of Solids in Residual Wastes from Single-Shell Tanks at the Hanford Site, Washington, USA - 9277

International Nuclear Information System (INIS)

Krupka, Kenneth M.; Cantrell, Kirk J.; Schaef, Herbert T.; Arey, Bruce W.; Heald, Steve M.; Deutsch, William J.; Lindberg, Michael J.

2009-01-01

Solid-phase characterization methods have been used in an ongoing study of residual wastes (i.e., waste remaining after final retrieval operations) from the underground single-shell storage tanks 241-C-103, 241-C-106, 241-C-202, 241-C-203, and 241-S-112 at the U.S. Department of Energy's Hanford Site in Washington State. The results of studies completed to date show significant variability in the compositions of those residual wastes and the compositions, morphologies, and crystallinities of the individual phases that make up these wastes. These differences undoubtedly result from the various waste types stored and transferred in and out each tank and the sluicing and retrieval operations used for waste retrieval. Our studies indicate that these residual wastes are chemically-complex assemblages of crystalline and amorphous solids that contain contaminants as discrete phases and/or co-precipitated within oxide phases. Depending on the specific tank, various solids (e.g., gibbsite; boehmite; dawsonite; cancrinite; Fe oxides such as hematite, goethite, and maghemite; rhodochrosite; lindbergite; whewellite; nitratine; and numerous amorphous or poorly crystalline phases) have been identified by X-ray diffraction and scanning electron microscopy/energy dispersive X-ray spectroscopy in residual wastes studied to date. Our studies also show that contact of residual wastes with Ca(OH)2- and CaCO3-saturated aqueous solutions, which were used as surrogates for the compositions of pore-fluid leachants derived from young and aged cements respectively, may alter the compositions of solid phases present in the contacted wastes. Fe oxides/hydroxides have been identified in all residual wastes studied to date. They occur in these wastes as discrete particles, particles intergrown within a matrix of other phases, and surface coatings on other particles or particle aggregates. These Fe oxides/hydroxides typically contain trace concentrations of other transition metals, such Cr, Mn

High-temperature vitrification of Hanford residual-liquid waste in a continuous melter

International Nuclear Information System (INIS)

Barnes, S.M.

1980-04-01

Over 270 kg of high-temperature borosilicate glass have been produced in a series of three short-term tests in the High-Temperature Ceramic Melter vitrification system at PNL. The glass produced was formulated to vitrify simulated Hanford residual-liquid waste. The tests were designed to (1) demonstrate the feasibility of utilizing high-temperature, continuous-vitrification technology for the immobilization of the residual-liquid waste, (2) test the airlift draining technique utilized by the high-temperature melter, (3) compare glass produced in this process to residual-liquid glass produced under laboratory conditions, (4) investigate cesium volatility from the melter during waste processing, and (5) determine the maximum residual-liquid glass production rate in the high-temperature melter. The three tests with the residual-liquid composition confirmed the viability of the continuous-melting vitrification technique for the immobilization of this waste. The airlift draining technique was demonstrated in these tests and the glass produced from the melter was shown to be less porous than the laboratory-produced glass. The final glass produced from the second test was compared to a glass of the same composition produced under laboratory conditions. The comparative tests found the glasses to be indistinguishable, as the small differences in the test results fell within the precision range of the characterization testing equipment. The cesium volatility was examined in the final test. This examination showed that 0.44 wt % of the cesium (assumed to be cesium oxide) was volatilized, which translates to a volatilization rate of 115 mg/cm 2 -h

Nutrient retention capabilities of Nile tilapia ( Oreochromis niloticus) fed bio-regenerative life support system (BLSS) waste residues

Science.gov (United States)

Gonzales, John M.; Brown, Paul B.

Nile tilapia were evaluated as a bio-regenerative sub-process for reducing solid waste potentially encountered in bio-regenerative life support systems. Ten juvenile Nile tilapia (mean weight = 2.05 g) were stocked into triplicate aquaria and fed one of seven experimental diets consisting of vegetable, bacterial, or food waste for a period of seven weeks. Weight gain (g), specific growth rate (mg/d), and daily consumption (g) was significantly higher ( p diet (37.99 and 68.54, respectively) followed by fish fed the wheat bran/wheat germ diet (23.19 and 63.67, respectively). Nitrogen, sulfur, and crude protein retention was significantly higher ( p diet (23.68, 21.89, and 23.68, respectively). A general loss of minerals was observed among all groups. Strong associations were observed between crude lipid retention and sulfur retention ( r2 = 0.94), crude lipid retention and carbon retention ( r2 = 0.92), WG and fiber content of dietary treatments ( r2 = 0.92), WG and carbon retention and ( r2 = 0.88), WG and lysine content of waste residues ( r2 = 0.86), crude protein retention and carbon retention ( r2 = 0.84), sulfur retention and crude protein retention ( r2 = 0.84), and total sulfur amino acid (TSAA) content of residues and WG ( r2 = 0.81). Weaker associations existed between WG and crude lipid retention ( r2 = 0.77), crude fiber content and carbon retention ( r2 = 0.76), and WG and methionine content of waste residues ( r2 = 0.75). Additional research is needed to improve the nutritional quality of fibrous residues as a means to improve tilapia's ability to utilize these residues as a food source in bio-regenerative support systems.

Waste incineration

International Nuclear Information System (INIS)

Rumplmayr, A.; Sammer, G.

2001-01-01

Waste incineration can be defined as the thermal conversion processing of solid waste by chemical oxidation. The types of wastes range from solid household waste and infectious hospital waste through to toxic solid, liquid and gaseous chemical wastes. End products include hot incineration gases, composed primarily of nitrogen, carbon dioxide, water vapor and to a smaller extend of non-combustible residue (ash) and air pollutants (e. g. NO x ). Energy can be recovered by heat exchange from the hot incineration gases, thus lowering fossil fuel consumption that in turn can reduce emissions of greenhouse gases. Burning of solid waste can fulfil up to four distinctive objectives (Pera, 2000): 1. Volume reduction: volume reduction of about 90 %, weight reduction of about 70 %; 2. Stabilization of waste: oxidation of organic input; 3. Recovery of energy from waste; 4. Sanitization of waste: destruction of pathogens. Waste incineration is not a means to make waste disappear. It does entail emissions into air as well as water and soil. The generated solid residues are the topic of this task force. Unlike other industrial processes discussed in this platform, waste incineration is not a production process, and is therefore not generating by-products, only residues. Residues that are isolated from e. g. flue gas, are concentrated in another place and form (e. g. air pollution control residues). Hence, there are generally two groups of residues that have to be taken into consideration: residues generated in the actual incineration process and others generated in the flue gas cleaning system. Should waste incineration finally gain public acceptance, it will be necessary to find consistent regulations for both sorts of residues. In some countries waste incineration is seen as the best option for the treatment of waste, whereas in other countries it is seen very negative. (author)

Decommissioning Combustible Waste Treatment using Oxygen-Enriched Incinerator

Energy Technology Data Exchange (ETDEWEB)

Min, Byungyoun; Lee, Yoonji; Yun, Gyoungsu; Lee, Kiwon; Moon, Jeikwon [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2014-05-15

The aim of the paper is current status of treatment for the decommissioning combustible waste in KAERI and for the purpose of the volume reduction and clearance for decommissioning combustible wastes generated by the decommissioning projects. The incineration technology has been selected for the treatment of combustible wastes. About 34 tons of decommissioning combustible waste has been treated using Oxygen Enriched incineration. Temperature, pressure of major components, stack gas concentration, i. e., SOx, NOx, CO, CO{sub 2} and HCl, and the residual oxygen were measured. Measured major parameters during normal operation were sustained on a stable status within a criteria operation condition. Oxygen enriched air, 22vol. % (dry basis) was used for stable incineration. The volume reduction ratio has achieved about 1/117. The incineration with decommissioning radioactive combustible waste is possible with moderate oxygen enrichment of 22 vol.% (dry basis) into the supply air. The incineration facility operated quite smoothly through the analysis major critical parameters of off-gas. The pressure, off-gas flow and temperature of major components remained constant within the range specified. The measures gases and particulate materials in stack were considerably below the regulatory limits. The achieved volume reduction ratio through incineration is about 1/117.

Evaluation of resource recovery from waste incineration residues--the case of zinc.

Science.gov (United States)

Fellner, J; Lederer, J; Purgar, A; Winterstetter, A; Rechberger, H; Winter, F; Laner, D

2015-03-01

Solid residues generated at European Waste to Energy plants contain altogether about 69,000 t/a of Zn, of which more than 50% accumulates in air pollution control residues, mainly boiler and filter ashes. Intensive research activities aiming at Zn recovery from such residues recently resulted in a technical scale Zn recovery plant at a Swiss waste incinerator. By acidic leaching and subsequent electrolysis this technology (FLUREC) allows generating metallic Zn of purity>99.9%. In the present paper the economic viability of the FLUREC technology with respect to Zn recovery from different solid residues of waste incineration has been investigated and subsequently been categorised according to the mineral resource classification scheme of McKelvey. The results of the analysis demonstrate that recovery costs for Zn are highly dependent on the costs for current fly ash disposal (e.g. cost for subsurface landfilling). Assuming current disposal practice costs of 220€/ton fly ash, resulting recovery costs for Zn are generally higher than its current market price of 1.6€/kg Zn. With respect to the resource classification this outcome indicates that none of the identified Zn resources present in incineration residues can be economically extracted and thus cannot be classified as a reserve. Only for about 4800 t/a of Zn an extraction would be marginally economic, meaning that recovery costs are only slightly (less than 20%) higher than the current market price for Zn. For the remaining Zn resources production costs are between 1.5 and 4 times (7900 t/a Zn) and 10-80 times (55,300 t/a Zn) higher than the current market value. The economic potential for Zn recovery from waste incineration residues is highest for filter ashes generated at grate incinerators equipped with wet air pollution control. Copyright © 2014 Elsevier Ltd. All rights reserved.

Effects of residues from municipal solid waste landfill on corn yield and heavy metal content

International Nuclear Information System (INIS)

Prabpai, S.; Charerntanyarak, L.; Siri, B.; Moore, M.R.; Noller, Barry N.

2009-01-01

The effects of residues from municipal solid waste landfill, Khon Kaen Municipality, Thailand, on corn (Zea mays L.) yield and heavy metal content were studied. Field experiments with randomized complete block design with five treatments (0, 20, 40, 60 and 80% v/v of residues and soil) and four replications were carried out. Corn yield and heavy metal contents in corn grain were analyzed. Corn yield increased by 50, 72, 85 and 71% at 20, 40, 60 and 80% treatments as compared to the control, respectively. All heavy metals content, except cadmium, nickel and zinc, in corn grain were not significantly different from the control. Arsenic, cadmium and zinc in corn grain were strongly positively correlated with concentrations in soil. The heavy metal content in corn grain was within regulated limits for human consumption.

Gasification of fruit wastes and agro-food residues in supercritical water

International Nuclear Information System (INIS)

Nanda, Sonil; Isen, Jamie; Dalai, Ajay K.; Kozinski, Janusz A.

2016-01-01

Highlights: • Supercritical water gasification of various fruit wastes and agro-food residues. • Coconut shell had superior carbon content and calorific value due to high lignin. • Maximum H_2 yields at 600 °C with 1:10 biomass-to-water ratio, 45 min and 23–25 MPa. • High H_2 yields from coconut shell, bagasse and aloe vera rind with 2 wt% K_2CO_3. • High CH_4 yields from coconut shell with 2 wt% NaOH due to methanation reaction. - Abstract: Considerable amounts of fruit wastes and agro-food residues are generated worldwide as a result of food processing. Converting the bioactive components (e.g., carbohydrates, lipids, fats, cellulose, hemicellulose and lignin) in food wastes to biofuels is a potential remediation approach. This study highlights the characterization and hydrothermal conversion of several fruit wastes and agro-food residues such as aloe vera rind, banana peel, coconut shell, lemon peel, orange peel, pineapple peel and sugarcane bagasse to hydrogen-rich syngas through supercritical water gasification. The agro-food wastes were gasified in supercritical water to study the impacts of temperature (400–600 °C), biomass-to-water ratio (1:5 and 1:10) and reaction time (15–45 min) at a pressure range of 23–25 MPa. The catalytic effects of NaOH and K_2CO_3 were also investigated to maximize the hydrogen yields and selectivity. The elevated temperature (600 °C), longer reaction time (45 min) and lower feed concentration (1:10 biomass-to-water ratio) were optimal for higher hydrogen yield (0.91 mmol/g) and total gas yield (5.5 mmol/g) from orange peel. However, coconut shell with 2 wt% K_2CO_3 at 600 °C and 1:10 biomass-to-water ratio for 45 min revealed superior hydrogen yield (4.8 mmol/g), hydrogen selectivity (45.8%) and total gas yield (15 mmol/g) with enhanced lower heating value of the gas product (1595 kJ/Nm"3). The overall findings suggest that supercritical water gasification of fruit wastes and agro-food residues could serve as

Carbon speciation in ash, residual waste and contaminated soil by thermal and chemical analyses.

Science.gov (United States)

Kumpiene, Jurate; Robinson, Ryan; Brännvall, Evelina; Nordmark, Désirée; Bjurström, Henrik; Andreas, Lale; Lagerkvist, Anders; Ecke, Holger

2011-01-01

Carbon in waste can occur as inorganic (IC), organic (OC) and elemental carbon (EC) each having distinct chemical properties and possible environmental effects. In this study, carbon speciation was performed using thermogravimetric analysis (TGA), chemical degradation tests and the standard total organic carbon (TOC) measurement procedures in three types of waste materials (bottom ash, residual waste and contaminated soil). Over 50% of the total carbon (TC) in all studied materials (72% in ash and residual waste, and 59% in soil) was biologically non-reactive or EC as determined by thermogravimetric analyses. The speciation of TOC by chemical degradation also showed a presence of a non-degradable C fraction in all materials (60% of TOC in ash, 30% in residual waste and 13% in soil), though in smaller amounts than those determined by TGA. In principle, chemical degradation method can give an indication of the presence of potentially inert C in various waste materials, while TGA is a more precise technique for C speciation, given that waste-specific method adjustments are made. The standard TOC measurement yields exaggerated estimates of organic carbon and may therefore overestimate the potential environmental impacts (e.g. landfill gas generation) of waste materials in a landfill environment. Copyright © 2010 Elsevier Ltd. All rights reserved.

[Do pharmaceutical waste and drug residue pose a risk to public health?].

Science.gov (United States)

Haguenoer, Jean-Marie

2010-01-01

Recently, awareness has developed of the environmental consequences of drug waste and disposal. These residues are identified as coming from either diffuse sources, the most significant of which is via the discharge of these residues in urine and feces, and thus the sewage system and water contains these drug remnants and their metabolites, or from point sources, sometimes with very high levels of concentration in waste from chemical and pharmaceutical industries, health care settings, but also from intensive livestock farming and aquaculture. Depending on their physical chemistry properties, these substances are more or less naturally biodegradable and easily treated in sewage purification plants. The effectiveness of these treatment processes is highly random and unpredictable, but is overall around 60%, nevertheless with variations of 2-99% according to the molecules. The silt from these treatment plants, sometimes very rich in lipophilic substances is on occasion reused for agricultural application as fertilizer, paving the way for a possible contamination of crops. Furthermore, the use of veterinary drugs in animals can lead to soil contamination either directly or through manure and slurry. The contamination can equally reach and affect surface water, groundwater and sometimes the water intended for human consumption. The National academy of Pharmacy has established some general recommendations on the proper use of drugs, environmental monitoring and surveillance, risk assessment for humans and the environment, prevention and the need for prevention. Several categories of drugs are more worrying: cancer treatments, antibiotics as well as transfers of anti-bio-resistance, and hormonal derivatives which has been previously demonstrated to contribute, along with other molecules, to detrimental effects on endocrines.

Characterization and treatment of cyanide in MGP purifier wastes

Energy Technology Data Exchange (ETDEWEB)

Theis, T.L. [Clarkson University, Potsdam, NY (United States). Dept. of Civil and Environmental Engineering

1995-12-31

Purifier wastes were generated from the clean-up gaseous impurities, principally hydrogen sulfide and hydrogen cyanide, contained in raw gas from MGP operations through retention by iron oxide solids. These materials were generated at a rate of about 10-20 kg/1000 m{sup 3} of gas produced, and although regeneration was sometimes practised, eventual disposal as fill material, usually on site, was eventually necessary. The remediation of MGP sites generally requires that the disposition of these waste solids be addressed. The effective treatment of purifier wastes presents special problems due to the acid-base properties of the material, its elevated sulfur content, and the significant quantities of carbon both added as wood shavings and present as compounds generated as a result of gas manufacture. In broad terms, treatment approaches can be divided into two classes, those aimed at destroying the cyanide and objectionable carbon compounds and otherwise disposing of the residual, and those which attempt to isolate the waste from its surroundings. The latter approach attempts to take advantage of the natural insolubility of most of the constituents of concern found in purifier wastes, while destructive technologies limit potential liability. 9 refs.

Integrated process analysis of treatment systems for mixed low level waste

International Nuclear Information System (INIS)

Cooley, C.R.; Schwinkendorf, W.E.; Bechtold, T.E.

1997-10-01

Selection of technologies to be developed for treatment of DOE's mixed low level waste (MLLW) requires knowledge and understanding of the expected costs, schedules, risks, performance, and reliability of the total engineered systems that use these technologies. Thus, an integrated process analysis program was undertaken to identify the characteristics and needs of several thermal and nonthermal systems. For purposes of comparison, all systems were conceptually designed for a single facility processing the same amount of waste at the same rate. Thirty treatment systems were evaluated ranging from standard incineration to innovative thermal systems and innovative nonthermal chemical treatment. Treating 236 million pounds of waste in 20 years through a central treatment was found to be the least costly option with total life cycle cost ranging from $2.1 billion for a metal melting system to $3.9 billion for a nonthermal acid digestion system. Little cost difference exists among nonthermal systems or among thermal systems. Significant cost savings could be achieved by working towards maximum on line treatment time per year; vitrifying the final waste residue; decreasing front end characterization segregation and sizing requirements; using contaminated soil as the vitrifying agent; and delisting the final vitrified waste form from Resource Conservation and Recovery Act (RCRA) Land Disposal Restriction (LDR) requirements

TREATMENT OF METAL-LADEN HAZARDOUS WASTES WITH ADVANCED CLEAN COAL TECHNOLOGY BY-PRODUCTS

Energy Technology Data Exchange (ETDEWEB)

James T. Cobb, Jr.

2003-09-12

Metal-laden wastes can be stabilized and solidified using advanced clean coal technology by-products (CCTBs)--fluid bed combustor ash and spray drier solids. These utility-generated treatment chemicals are available for purchase through brokers, and commercial applications of this process are being practiced by treaters of metal-laden hazardous waste. A complex of regulations governs this industry, and sensitivities to this complex has discouraged public documentation of treatment of metal-laden hazardous wastes with CCTBs. This report provides a comprehensive public documentation of laboratory studies that show the efficacy of the stabilization and solidification of metal-laden hazardous wastes--such as lead-contaminated soils and sandblast residues--through treatment with CCTBs. It then describes the extensive efforts that were made to obtain the permits allowing a commercial hazardous waste treater to utilize CCTBs as treatment chemicals and to install the equipment required to do so. It concludes with the effect of this lengthy process on the ability of the treatment company to realize the practical, physical outcome of this effort, leading to premature termination of the project.

The Rocky Flats Plant Waste Stream and Residue Identification and Characterization Program (WSRIC): Progress and achievements

International Nuclear Information System (INIS)

Ideker, V.L.

1994-01-01

The Waste Stream and Residue Identification and Characterization (WSRIC) Program, as described in the WSRIC Program Description delineates the process knowledge used to identify and characterize currently-generated waste from approximately 5404 waste streams originating from 576 processes in 288 buildings at Rocky Flats Plant (RFP). Annual updates to the WSRIC documents are required by the Federal Facilities Compliance Agreement between the US Department of Energy, the Colorado Department of Health and the Environmental Protection Agency. Accurate determination and characterization of waste is a crucial component in RFP's waste management strategy to assure compliance with Resource Conservation and Recovery Act (RCRA) storage and treatment requirements, as well as disposal acceptance criteria. The WSRIC Program was rebaselined in September 1992, and serves as the linchpin for documenting process knowledge in RFP's RCRA operating record. Enhancements to the WSRIC include strengthening the waste characterization rationale, expanding WSRIC training for waste generators, and incorporating analytical information into the WSRIC building books. These enhancements will improve credibility with the regulators and increase waste generators' understanding of the basis for credible waste characterizations

Boundaries matter: Greenhouse gas emission reductions from alternative waste treatment strategies for California’s municipal solid waste

DEFF Research Database (Denmark)

Vergara, Sintana E.; Damgaard, Anders; Horvathc, Arpad

2011-01-01

How waste is managed – whether as a nuisance to be disposed of, or as a resource to be reused – directly affects local and global environmental quality. This analysis explores the GHG benefits of five treatment options for residual municipal solid waste (MSW) in California: Business As Usual...... landfills. Using two different waste LCA models, EASEWASTE (a Danish model) and WARM (a U.S. model), we find that improved biogenic waste management through anaerobic digestion and waste reduction can lead to life-cycle GHG savings when compared to Business As Usual. The magnitude of the benefits depends...... strongly on a number of model assumptions: the type of electricity displaced by waste-derived energy, how biogenic carbon is counted as a contributor to atmospheric carbon stocks, and the landfill gas collection rate. Assuming that natural gas is displaced by waste-derived energy, that 64% of landfill gas...

Economic optimization of waste treatment and energy production in Denmark

DEFF Research Database (Denmark)

Münster, Marie; Ravn, Hans; Hedegaard, Karsten

2013-01-01

This article presents an optimization model that incorporates LCA methodology and captures important characteristics of waste management systems. The most attractive waste management options are in the model identified as part the optimization. The model renders it possible to apply different...... optimization objectives such as minimizing costs or greenhouse gas emissions or to prioritise several objectives given different weights. An illustrative case is analyzed, covering alternative treatments of 1 tonne residual household waste: incineration of the full amount or sorting out organic waste...... for biogas production for either CHP generation or as fuel in vehicles. The case study illustrates, that what is the optimal solution depends on the objective and assumptions regarding the background system – here illustrated with different assumptions regarding displaced electricity production. The article...

Urban Mining: Quality and quantity of recyclable and recoverable material mechanically and physically extractable from residual waste

International Nuclear Information System (INIS)

Di Maria, Francesco; Micale, Caterina; Sordi, Alessio; Cirulli, Giuseppe; Marionni, Moreno

2013-01-01

Highlights: • Material recycling and recovery from residual waste by physical and mechanical process has been investigated. • About 6% of recyclable can be extracted by NIR and 2-3Dimension selector. • Another 2% of construction materials can be extracted by adopting modified soil washing process. • Extracted material quality is quite high even some residual heavy metal have been detected by leaching test. - Abstract: The mechanically sorted dry fraction (MSDF) and Fines (<20 mm) arising from the mechanical biological treatment of residual municipal solid waste (RMSW) contains respectively about 11% w/w each of recyclable and recoverable materials. Processing a large sample of MSDF in an existing full-scale mechanical sorting facility equipped with near infrared and 2-3 dimensional selectors led to the extraction of about 6% w/w of recyclables with respect to the RMSW weight. Maximum selection efficiency was achieved for metals, about 98% w/w, whereas it was lower for Waste Electrical and Electronic Equipment (WEEE), about 2% w/w. After a simulated lab scale soil washing treatment it was possible to extract about 2% w/w of inert exploitable substances recoverable as construction materials, with respect to the amount of RMSW. The passing curve showed that inert materials were mainly sand with a particle size ranging from 0.063 to 2 mm. Leaching tests showed quite low heavy metal concentrations with the exception of the particles retained by the 0.5 mm sieve. A minimum pollutant concentration was in the leachate from the 10 and 20 mm particle size fractions

Geochemical Testing And Model Development - Residual Tank Waste Test Plan

International Nuclear Information System (INIS)

Cantrell, K.J.; Connelly, M.P.

2010-01-01

This Test Plan describes the testing and chemical analyses release rate studies on tank residual samples collected following the retrieval of waste from the tank. This work will provide the data required to develop a contaminant release model for the tank residuals from both sludge and salt cake single-shell tanks. The data are intended for use in the long-term performance assessment and conceptual model development.

A process for treatment of residues from dry/semidry APC systems at municipal solid waste incinerators. Final report

Energy Technology Data Exchange (ETDEWEB)

Hjelmar, O. [VKI, Hoersholm (Denmark)] Holland, D. [FLS miljoe a/s, Valby (Denmark)] Poulsen, B. [KARA, Roskilde (Denmark)

1997-08-01

The main objective of the project has been to establish and test a process for treatment of residues from the semidry (and dry) lime injection based APC processes at MSWIs, which will ensure that the residues can be managed in an environmentally safe manner. In pursuit of this goal, the following activities have been carried out: Performance of pilot scale extractions (approximately 50 kg of residue per batch) at the KARA MSWI in Roskilde of semidry APC system residues in order to establish and optimize process conditions. The optimization includes consideration of the possibilities for subsequent treatment/stabilization of the extracted solid phase as well as the possibility of treatment and safe discharge/utilization of the extract; Performance of chemical characterization, hydrogeochemical model calculations and experimental work in order to improve the understanding of the mechanisms and factors which for several contaminants control the equilibrium between the solid and liquid phases, both in the short and the long germ, and to use this information to obtain an environmentally acceptable method for stabilization/treatment of the extracted residues while at the same time minimizing the necessary amount of additives; production of treated residues and performance of leaching tests on these to assess and demonstrate the effectiveness of the entire process (extraction + stabilization/treatment); Evaluation of the technical, economical and environmental consequences of full scale implementation of the process. (EG) EFP-94. 19 refs.

Treatment and final storage of radioactive wastes from the nuclear fuel cycle

Energy Technology Data Exchange (ETDEWEB)

Krause, H [Kernforschungszentrum Karlsruhe (Germany, F.R.)

1977-05-01

Types, amounts and activity concentrations of the radioactive wastes arising from the different sections of the fuel cycle are described as well as the methods of their treatment and final disposal. By conversion to glass products, highly active fission product solutions can be transferred into a form well suited for final disposal. Low and medium level waste waters are purified so far that safe discharge or reuse is possible. The concentrates thus produced are incorporated into concrete or bitumen. Baling lends itself for treatment of non-combustible solid wastes. Combustible wastes can be incinerated, the residues are incorporated into concrete. For final storage of the conditioned wastes, salt formations in the deep underground are chosen in the Federal Republic of Germany. They offer a series of favourable preconditions for this purpose and guarantee the isolation of the radionuclides from the biocycle over secular periods of time.

Thermochemical treatment of radioactive waste by using powder metal fuels

International Nuclear Information System (INIS)

Dmitriev, S.A.; Ojovan, M.I.; Karlina, O.K.

2001-01-01

waste; 4. Processing of irradiated graphite. (1). The decontamination technique based on application of PMF is used in order to decontaminate materials (asphalt, concrete, metal), which usually cannot be decontaminated by conventional methods. A thin layer of PMF covers contaminated materials, thereafter this layer is burned during 10-20 minutes. Temperatures from 300 to 1500 C and higher (depending on the composition of PMF) are overreached in the process of PMF combustion. The radionuclides are volatilised from material being heated, after that cold layer of slag-like products of combustion adsorbs them. This slag has a porous structure with highly developed interface providing adsorption of radionuclides. After cooling the slag is removed mechanically jointly with contamination. The efficiency of decontamination process depends on many parameters however practically complete decontamination can be achieved using appropriate PMF. (2). Thermochemical treatment of spent ion exchange resins is carried out using a modular facility. Wet resins and PMF previously mixed in appropriate ratio are fed into a furnace where the reaction is initiated and combustion proceeds. The metal powder contained in the PMF is in the contact with the resin granules and reacts with the moisture contained in the granules with the resulting release of the great quantity of heat. This heat is sufficient for the moisture to evaporate and the ion exchange resin to be gasified. A high efficiency can be obtained for the incineration of wet ion exchange resins mixed with PMF. PMF provides complete destruction of the organic base of the ion exchange resins with minimal release of hazardous gases and radionuclides into the environment. (3). Dusty waste (like ash residue) requires stabilisation - vitrification in order to ensure safe conditions for transportation and disposal. Vitrification of dusty waste is a process carried out directly in the container for disposal. It consists of intermixing of dusty

Hanford Site Tank 241-C-108 Residual Waste Contaminant Release Models and Supporting Data

Energy Technology Data Exchange (ETDEWEB)

Cantrell, Kirk J.; Krupka, Kenneth M.; Geiszler, Keith N.; Arey, Bruce W.; Schaef, Herbert T.

2010-06-18

This report presents the results of laboratory characterization, testing, and analysis for a composite sample (designated 20578) of residual waste collected from single-shell tank C-108 during the waste retrieval process after modified sluicing. These studies were completed to characterize concentration and form of contaminant of interest in the residual waste; assess the leachability of contaminants from the solids; and develop release models for contaminants of interest. Because modified sluicing did not achieve 99% removal of the waste, it is expected that additional retrieval processing will take place. As a result, the sample analyzed here is not expected to represent final retrieval sample.

Radioactive wastes and residues: government participation in a control policy

International Nuclear Information System (INIS)

Gelli, Guido

1993-01-01

This paper discusses the politic aspects of the State participation in inspection and control of the radioactive wastes residues with the supervise of Brazilian Nuclear Energy Commission (CNEN), by a national program

Comparison of scientific and engineering approaches to the treatment of mixed wastes

International Nuclear Information System (INIS)

Gilbert, K.V.; Bowers, J.S.

1993-12-01

This paper discusses two approaches to the treatment of mixed waste. (Mixed waste, defined as radioactive waste that is co-contaminated with hazardous waste as defined in the Resource Conservation and Conservation Act, is presently stored throughout the United States awaiting the establishment of treatment capability.)The first approach employs conventional engineering that focuses on low risk technology which has been proven in other industries in similar applications and is adaptable for waste treatment use. The term ''low risk'' means that implementation success is relatively certain, and the major uncertainty is the degree of success. Technologies under consideration include centrifugation, evaporation, microfiltration and stabilization. Process offgases are treated with traditional scrubbers and carbon absorption units.For the scientific approach, Lawrence Livermore National Laboratory is in the conceptual design phase of a project to demonstrate incinerator alternatives to destroy organic contaminants in radioactive waste streams without the use of incineration. This Mixed Waste Management Facility will use approximately 15000 square feet of an existing facility to demonstrate an integrated waste management system. Robotic and telerobotic systems will be employed for waste segregation, characterization and feed preparation. Waste feeds will be treated using molten salt oxidation, mediated electrochemical oxidation and wet oxidation. Residues, which can be managed as radioactive-only waste, will be immobilized in an organic matrix prior to shipment to an authorized disposal site

Thermal plasma waste treatment

International Nuclear Information System (INIS)

Heberlein, Joachim; Murphy, Anthony B

2008-01-01

Plasma waste treatment has over the past decade become a more prominent technology because of the increasing problems with waste disposal and because of the realization of opportunities to generate valuable co-products. Plasma vitrification of hazardous slags has been a commercial technology for several years, and volume reduction of hazardous wastes using plasma processes is increasingly being used. Plasma gasification of wastes with low negative values has attracted interest as a source of energy and spawned process developments for treatment of even municipal solid wastes. Numerous technologies and approaches exist for plasma treatment of wastes. This review summarizes the approaches that have been developed, presents some of the basic physical principles, provides details of some specific processes and considers the advantages and disadvantages of thermal plasmas in waste treatment applications. (topical review)

Environmental impact of APC residues from municipal solid waste incineration: reuse assessment based on soil and surface water protection criteria.

Science.gov (United States)

Quina, Margarida J; Bordado, João C M; Quinta-Ferreira, Rosa M

2011-01-01

Waste management and environmental protection are mandatory requirements of modern society. In our study, air pollution control (APC) residues from municipal solid waste incinerators (MSWI) were considered as a mixture of fly ash and fine particulate solids collected in scrubbers and fabric filters. These are hazardous wastes and require treatment before landfill. Although there are a number of treatment options, it is highly recommended to find practical applications rather than just dump them in landfill sites. In general, for using a construction material, beyond technical specifications also soil and surface water criteria may be used to ensure environmental protection. The Dutch Building Materials Decree (BMD) is a valuable tool in this respect and it was used to investigate which properties do not meet the threshold criteria so that APC residues can be further used as secondary building material. To this end, some scenarios were evaluated by considering release of inorganic species from unmoulded and moulded applications. The main conclusion is that the high amount of soluble salts makes the APC residues a building material prohibited in any of the conditions tested. In case of moulding materials, the limits of heavy metals are complied, and their use in Category 1 would be allowed. However, also in this case, the soluble salts lead to the classification of "building material not allowed". The treatments with phosphates or silicates are able to solve the problem of heavy metals, but difficulties with the soluble salts are still observed. This analysis suggests that for APC residues to comply with soil and surface water protection criteria to be further used as building material at least a pre-treating for removing soluble salts is absolutely required. Copyright © 2011 Elsevier Ltd. All rights reserved.

Argonne National Laboratory's photo-oxidation organic mixed waste treatment system - installation and startup testing

International Nuclear Information System (INIS)

Shearer, T.L.; Nelson, R.A.; Torres, T.; Conner, C.; Wygmans, D.

1997-01-01

This paper describes the installation and startup testing of the Argonne National Laboratory (ANL-E) Photo-Oxidation Organic Mixed Waste Treatment System. This system will treat organic mixed (i.e., radioactive and hazardous) waste by oxidizing the organics to carbon dioxide and inorganic salts in an aqueous media. The residue will be treated in the existing radwaste evaporators. The system is installed in the Waste Management Facility at the ANL-E site in Argonne, Illinois. 1 fig

Treatment strategies for transuranic wastes

International Nuclear Information System (INIS)

Schneider, K.J.; Ross, W.A.; Swanson, J.L.; Allen, R.P.; Yasutake, K.M.

1986-01-01

This paper presents an analysis of treatment options or strategies for transuranic wastes expected to be generated at a commercial nuclear fuel reprocessing plant. Six potential options were analyzed, ranging from no treatment to maximum volume reduction and high quality waste forms. Economics for the total management of these wastes (treatment, transportation, disposal) indicate life-cycle savings for extensive treatment are as high as $1.7 billion for 70,000 MTU. Evaluations of the waste processing and waste forms support the selection of a number of the extensive waste treatments. It is concluded that there are significant incentives for extensive treatment of transuranic wastes

Solid radioactive waste: evaluation of residual activity in nuclear medicine services

International Nuclear Information System (INIS)

Alabarse, Frederico G.; Xavier, Ana M.; Magalhaes, Maisa H.; Guerrero, Jesus S.P.

2009-01-01

An experimental programme to estimate, with a better degree of accuracy, the activity that remains adsorbed in flasks and syringes used in Nuclear Medicine Services for the administration of radionuclides to patients submitted to diagnostic or therapy is been conducted under the coordination of the Radioactive Waste Division of the Brazilian Nuclear Energy Commission, CNEN. The adopted recommendation in Brazil to allow an expedite solid waste management in nuclear medicine facilities, up to the present, is to consider that 2% of the initial activity remains adsorbed in the solid waste, which easily allows the calculation of the storage time to achieve regulatory clearance levels by decay. This research evaluates 17 different kinds of radiopharmaceuticals and three radioisotopes: 99m Tc, 67 Ga and 201 Tl. Results obtained by means of a weighting method to estimate the residual mass in flasks show that the ratio of the mass of the liquid that remains in the solid waste to the mass of the empty flask is constant. This suggests that the residual activity depends on the initial activity concentration of radiopharmaceutical contained in each flask, as assumed by the regulatory body. Additionally, results obtained by determining the remaining activity in flasks, shortly after the injection of its radionuclide contents in patients, indicate that an average value for the residual activity of the order of 10% of the initial activity contained in the flasks or syringes should be adopted to determine the decay storage time before the release of solid waste in the urban conventional land fill disposal system. The 'rule of thumb' of 10 half-lives for storage before clearance is also discussed in the present work. (author)

Biological treatment of concentrated hazardous, toxic, andradionuclide mixed wastes without dilution

Energy Technology Data Exchange (ETDEWEB)

Stringfellow, William T.; Komada, Tatsuyuki; Chang, Li-Yang

2004-06-15

Approximately 10 percent of all radioactive wastes produced in the U. S. are mixed with hazardous or toxic chemicals and therefore can not be placed in secure land disposal facilities. Mixed wastes containing hazardous organic chemicals are often incinerated, but volatile radioactive elements are released directly into the biosphere. Some mixed wastes do not currently have any identified disposal option and are stored locally awaiting new developments. Biological treatment has been proposed as a potentially safer alternative to incineration for the treatment of hazardous organic mixed wastes, since biological treatment would not release volatile radioisotopes and the residual low-level radioactive waste would no longer be restricted from land disposal. Prior studies have shown that toxicity associated with acetonitrile is a significant limiting factor for the application of biotreatment to mixed wastes and excessive dilution was required to avoid inhibition of biological treatment. In this study, we demonstrate that a novel reactor configuration, where the concentrated toxic waste is drip-fed into a complete-mix bioreactor containing a pre-concentrated active microbial population, can be used to treat a surrogate acetonitrile mixed waste stream without excessive dilution. Using a drip-feed bioreactor, we were able to treat a 90,000 mg/L acetonitrile solution to less than 0.1 mg/L final concentration using a dilution factor of only 3.4. It was determined that the acetonitrile degradation reaction was inhibited at a pH above 7.2 and that the reactor could be modeled using conventional kinetic and mass balance approaches. Using a drip-feed reactor configuration addresses a major limiting factor (toxic inhibition) for the biological treatment of toxic, hazardous, or radioactive mixed wastes and suggests that drip-feed bioreactors could be used to treat other concentrated toxic waste streams, such as chemical warfare materiel.

Treatment strategies for transuranic wastes

International Nuclear Information System (INIS)

Schneider, K.J.; Swanson, J.L.; Ross, W.A.; Allen, R.P.; Yasutake, K.M.

1986-01-01

This paper presents an analysis of treatment options or strategies for transuranic wastes expected to be generated at a commercial nuclear fuel reprocessing plant. Six potential options were analyzed, ranging from no treatment to maximum volume reduction and high quality waste forms. Economics for the total management of these (treatment, transportation, disposal) indicate life-cycle savings for extensive treatment are as high as $1.7 billion for 70,000 MTU. Evaluations of the waste processing and waste forms support the selection of a number of the extensive waste treatments. It is concluded that there are significant incentives for extensive treatment of transuranic wastes

Follow-up on analysis of dioxins in residues from Swedish waste incineration; Uppfoeljande undersoekning av dioxin i rester fraan svensk avfallsfoerbraenning

Energy Technology Data Exchange (ETDEWEB)

Lindskog, Aasa (Tyrens, Stockholm (Sweden)) (ed.)

2009-10-15

As a consequence of a debate in the late 1990's, a major study of the residues from waste incineration was performed in Sweden. In 1999, samples were collected from 21 of the 22, at the time, existing plants. Focus of the study was to analyse dioxin in flue gas treatment residue. A few analyses were also done on slag/bottom ash. A new follow-up study was decided to be carried out after some years. The present report present the result from the follow-up study from 2006 where 24 out of 29 waste incineration plants participated. Between 1999 and 2006 a number of changes have taken place in the waste incineration industry. A few new plants have been built, a few have been closed, a new and stricter law has come into force and the technical development has continued. These changes have together led to a positive development for waste incineration. As a result, the dioxin content in the flue gas residues has decreased, when the results from the two studies are being compared. The decrease is even larger for slag/bottom ash. In the 1999 study the dioxin content in the flue gas treatment residues varied from 0,2 ng/g to 18 ng/g (I-TEQ) with an average of 2-3 ng/g. The total amount for all plants was 160 g. The variation between the dioxin content in the flue gas treatment residues in the later study is smaller, the lowest value is 0,3 ng/g and the highest 5 ng/g. The average is 1,6 ng/g and the median is 1,2 ng/g, both lower that the values from 1999. The total dioxin amount for 2006 is larger than for 1999, 185 g. Although, it must be considered that the amount of incinerated waste has almost doubled during the same period. The dioxin content in the slag/bottom ash has decreased since the former study was performed. At 1999, samples of slag/bottom ash from only seven plants were analysed. The median was 0,03 ng/g and the total dioxin amount from all plants was approximated to 10 g. In the 2006 study the median amounted to 0,005 ng/g and the total amount to 9 g

Life cycle assessment of post-consumer plastics production from waste electrical and electronic equipment (WEEE) treatment residues in a Central European plastics recycling plant

International Nuclear Information System (INIS)

Wäger, Patrick A.; Hischier, Roland

2015-01-01

Plastics play an increasingly important role in reaching the recovery and recycling rates defined in the European WEEE Directive. In a recent study we have determined the life cycle environmental impacts of post-consumer plastics production from mixed, plastics-rich WEEE treatment residues in the Central European plant of a market-leading plastics recycler, both from the perspective of the customers delivering the residues and the customers buying the obtained post-consumer recycled plastics. The results of our life cycle assessments, which were extensively tested with sensitivity analyses, show that from both perspectives plastics recycling is clearly superior to the alternatives considered in this study (i.e. municipal solid waste incineration (MSWI) and virgin plastics production). For the three ReCiPe endpoint damage categories, incineration in an MSWI plant results in an impact exceeding that of the examined plastics recycling facility each by about a factor of 4, and the production of virgin plastics has an impact exceeding that of the post-consumer recycled (PCR) plastics production each by a factor of 6–10. On a midpoint indicator level the picture is more differentiated, showing that the environmental impacts of the recycling options are lower by 50% and more for almost all impact factors. While this provides the necessary evidence for the environmental benefits of plastics recycling compared to existing alternatives, it can, however, not be taken as conclusive evidence. To be conclusive, future research will have to address the fate of hazardous substances in the outputs of such recycling systems in more detail. - Highlights: • LCA of plastics production from plastics-rich WEEE treatment residues • Multiple stakeholder perspectives addressed via different research questions • Plastics production from WEEE treatment residues clearly superior to alternatives • Robust results as demonstrated by extensive sensitivity analyses

Life cycle assessment of post-consumer plastics production from waste electrical and electronic equipment (WEEE) treatment residues in a Central European plastics recycling plant

Energy Technology Data Exchange (ETDEWEB)

Wäger, Patrick A., E-mail: patrick.waeger@empa.ch; Hischier, Roland

2015-10-01

Plastics play an increasingly important role in reaching the recovery and recycling rates defined in the European WEEE Directive. In a recent study we have determined the life cycle environmental impacts of post-consumer plastics production from mixed, plastics-rich WEEE treatment residues in the Central European plant of a market-leading plastics recycler, both from the perspective of the customers delivering the residues and the customers buying the obtained post-consumer recycled plastics. The results of our life cycle assessments, which were extensively tested with sensitivity analyses, show that from both perspectives plastics recycling is clearly superior to the alternatives considered in this study (i.e. municipal solid waste incineration (MSWI) and virgin plastics production). For the three ReCiPe endpoint damage categories, incineration in an MSWI plant results in an impact exceeding that of the examined plastics recycling facility each by about a factor of 4, and the production of virgin plastics has an impact exceeding that of the post-consumer recycled (PCR) plastics production each by a factor of 6–10. On a midpoint indicator level the picture is more differentiated, showing that the environmental impacts of the recycling options are lower by 50% and more for almost all impact factors. While this provides the necessary evidence for the environmental benefits of plastics recycling compared to existing alternatives, it can, however, not be taken as conclusive evidence. To be conclusive, future research will have to address the fate of hazardous substances in the outputs of such recycling systems in more detail. - Highlights: • LCA of plastics production from plastics-rich WEEE treatment residues • Multiple stakeholder perspectives addressed via different research questions • Plastics production from WEEE treatment residues clearly superior to alternatives • Robust results as demonstrated by extensive sensitivity analyses.

A centralized hazardous waste treatment plant: the facilities of the ZVSMM at Schwabach as an example

Energy Technology Data Exchange (ETDEWEB)

Amsoneit, Norbert [Zweckverband Sondermuell-Entsorgung Mittelfranken, Rednitzhembach (Germany)

1994-12-31

In this work a centralized hazardous waste treatment plant is described and its infra-structure is presented. Special emphasis is given to the handling of the residues produced and the different treatment processes at the final disposal. 2 refs., 4 figs.

A centralized hazardous waste treatment plant: the facilities of the ZVSMM at Schwabach as an example

Energy Technology Data Exchange (ETDEWEB)

Amsoneit, Norbert [Zweckverband Sondermuell-Entsorgung Mittelfranken, Rednitzhembach (Germany)

1993-12-31

In this work a centralized hazardous waste treatment plant is described and its infra-structure is presented. Special emphasis is given to the handling of the residues produced and the different treatment processes at the final disposal. 2 refs., 4 figs.

Waste management, waste resource facilities and waste conversion processes

International Nuclear Information System (INIS)

Demirbas, Ayhan

2011-01-01

In this study, waste management concept, waste management system, biomass and bio-waste resources, waste classification, and waste management methods have been reviewed. Waste management is the collection, transport, processing, recycling or disposal, and monitoring of waste materials. A typical waste management system comprises collection, transportation, pre-treatment, processing, and final abatement of residues. The waste management system consists of the whole set of activities related to handling, treating, disposing or recycling the waste materials. General classification of wastes is difficult. Some of the most common sources of wastes are as follows: domestic wastes, commercial wastes, ashes, animal wastes, biomedical wastes, construction wastes, industrial solid wastes, sewer, biodegradable wastes, non-biodegradable wastes, and hazardous wastes.

Hanford Tank 241-C-106: Impact of Cement Reactions on Release of Contaminants from Residual Waste

International Nuclear Information System (INIS)

Deutsch, William J.; Krupka, Kenneth M.; Lindberg, Michael J.; Cantrell, Kirk J.; Brown, Christopher F.; Schaef, Herbert T.

2006-01-01

The CH2M HILL Hanford Group, Inc. (CH2M HILL) is producing risk/performance assessments to support the closure of single-shell tanks at the U.S. Department of Energy's Hanford Site. As part of this effort, staff at Pacific Northwest National Laboratory were asked to develop release models for contaminants of concern that are present in residual sludge remaining in tank 241-C-106 (C-106) after final retrieval of waste from the tank. Initial work to produce release models was conducted on residual tank sludge using pure water as the leaching agent. The results were reported in an earlier report. The decision has now been made to close the tanks after waste retrieval with a cementitious grout to minimize infiltration and maintain the physical integrity of the tanks. This report describes testing of the residual waste with a leaching solution that simulates the composition of water passing through the grout and contacting the residual waste at the bottom of the tank.

Waste treatment plant

International Nuclear Information System (INIS)

Adesanmi, C.A

2009-01-01

Waste Treatment Plant (WTP) is designed to provide appropriate systems for processing, immobilization and storage of low and medium radioactive waste arising from the operation of the research facilities of the Nuclear Technology Centre (NTC). It will serve as central collection station processing active waste generated through application of radionuclide in science, medicine and industry in the country. WTP building and structures will house the main waste processing systems and supporting facilities. All facilities will be interconnected. The interim storage building for processed waste drums will be located separately nearby. The separate interim storage building is located near the waste treatment building. Considering the low radiation level of the waste, storage building is large with no solid partitioning walls and with no services or extra facilities other than lighting and smoke alarm sensors. The building will be designed such that drums(200-1)are stacked 3 units high using handling by fork lift truck. To prevent radiation exposure to on-site personnel, the interim storage building will be erected apart from waste treatment plant or other buildings. The interim storage building will also be ready for buffer storage of unconditioned waste waiting for processing or decay and for storage material from the WTP

Environmental impact of APC residues from municipal solid waste incineration: Reuse assessment based on soil and surface water protection criteria

International Nuclear Information System (INIS)

Quina, Margarida J.; Bordado, Joao C.M.; Quinta-Ferreira, Rosa M.

2011-01-01

Highlights: → The Dutch Building Material Decree (BMD) was used to APC residues from MSWI. → BMD is a straightforward tool to calculate expectable loads to the environment of common pollutants. → Chloride load to the environment lead to classification of building material not allowed. → At least a pre-treatment (e.g. washing) is required in order to remove soluble salts. → The stabilization with phosphates or silicates eliminate the problem of heavy metals. - Abstract: Waste management and environmental protection are mandatory requirements of modern society. In our study, air pollution control (APC) residues from municipal solid waste incinerators (MSWI) were considered as a mixture of fly ash and fine particulate solids collected in scrubbers and fabric filters. These are hazardous wastes and require treatment before landfill. Although there are a number of treatment options, it is highly recommended to find practical applications rather than just dump them in landfill sites. In general, for using a construction material, beyond technical specifications also soil and surface water criteria may be used to ensure environmental protection. The Dutch Building Materials Decree (BMD) is a valuable tool in this respect and it was used to investigate which properties do not meet the threshold criteria so that APC residues can be further used as secondary building material. To this end, some scenarios were evaluated by considering release of inorganic species from unmoulded and moulded applications. The main conclusion is that the high amount of soluble salts makes the APC residues a building material prohibited in any of the conditions tested. In case of moulding materials, the limits of heavy metals are complied, and their use in Category 1 would be allowed. However, also in this case, the soluble salts lead to the classification of 'building material not allowed'. The treatments with phosphates or silicates are able to solve the problem of heavy metals, but

Waste treatment

International Nuclear Information System (INIS)

Hutson, G.V.

1996-01-01

Numerous types of waste are produced by the nuclear industry ranging from high-level radioactive and heat-generating, HLW, to very low-level, LLW and usually very bulky wastes. These may be in solid, liquid or gaseous phases and require different treatments. Waste management practices have evolved within commercial and environmental constraints resulting in considerable reduction in discharges. (UK)

Thermal decomposition of nitrate salts liquid waste for the lagoon sludge treatment

International Nuclear Information System (INIS)

Hwang, D. S.; Oh, J. H.; Kim, Y. K.; Lee, K. Y.; Choi, Y. D.; Hwang, S. T.; Park, J. H.

2004-01-01

This study investigated the thermal decomposition property of nitrate salts liquid waste which is produced in a series of the processes for the sludge treatment. Thermal decomposition property was analyzed by TG/DTA and XRD. Most ammonium nitrate in the nitrate salts liquid waste was decomposed at 250 .deg. C and calcium nitrate was decomposed and converted into calcium oxide at 550 .deg. C. Sodium nitrate was decomposed at 700 .deg. C and converted into sodium oxide which reacts with water easily. But sodium oxide was able to convert into a stable compound by adding alumina. Therefore, nitrate salts liquid waste can be treated by two steps as follows. First, ammonium nitrate is decomposed at 250 .deg. C. Second, alumina is added in residual solid sodium nitrate and calcium nitrate and these are decomposed at 900 .deg. C. Final residue consists of calcium oxide and Na 2 O.Al 2 O 3 and can be stored stably

Flow analysis of heavy metals in a pilot-scale incinerator for residues from waste electrical and electronic equipment dismantling

International Nuclear Information System (INIS)

Long, Yu-Yang; Feng, Yi-Jian; Cai, Si-Shi; Ding, Wei-Xu; Shen, Dong-Sheng

2013-01-01

Highlights: • Cu, Zn, Pb, and Ni are enriched in bottom ash from WEEE dismantling residues. • The heavy metal residual fraction restricts transfer in the incinerator. • Pre-treatment to remove heavy metals from WEEE residues would reduce emissions. -- Abstract: The large amount of residues generated from dismantling waste electrical and electronic equipment (WEEE) results in a considerable environmental burden. We used material flow analysis to investigate heavy metal behavior in an incineration plant in China used exclusively to incinerate residues from WEEE dismantling. The heavy metals tested were enriched in the bottom and fly ashes after incineration. However, the contents of heavy metals in the bottom ash, fly ash and exhaust gas do not have a significant correlation with that of the input waste. The evaporation and recondensation behavior of heavy metals caused their contents to differ with air pollution control equipment because of the temperature difference during gas venting. Among the heavy metals tested, Cd had the strongest tendency to transfer during incineration (T Cd = 69.5%) because it had the lowest melting point, followed by Cu, Ni, Pb and Zn. The exchangeable and residual fractions of heavy metals increased substantially in the incineration products compared with that of the input residues. Although the mass of residues from WEEE dismantling can be reduced by 70% by incineration, the safe disposal of the metal-enriched bottom and fly ashes is still required

Flow analysis of heavy metals in a pilot-scale incinerator for residues from waste electrical and electronic equipment dismantling

Energy Technology Data Exchange (ETDEWEB)

Long, Yu-Yang; Feng, Yi-Jian; Cai, Si-Shi; Ding, Wei-Xu; Shen, Dong-Sheng, E-mail: shends@zju.edu.cn

2013-10-15

Highlights: • Cu, Zn, Pb, and Ni are enriched in bottom ash from WEEE dismantling residues. • The heavy metal residual fraction restricts transfer in the incinerator. • Pre-treatment to remove heavy metals from WEEE residues would reduce emissions. -- Abstract: The large amount of residues generated from dismantling waste electrical and electronic equipment (WEEE) results in a considerable environmental burden. We used material flow analysis to investigate heavy metal behavior in an incineration plant in China used exclusively to incinerate residues from WEEE dismantling. The heavy metals tested were enriched in the bottom and fly ashes after incineration. However, the contents of heavy metals in the bottom ash, fly ash and exhaust gas do not have a significant correlation with that of the input waste. The evaporation and recondensation behavior of heavy metals caused their contents to differ with air pollution control equipment because of the temperature difference during gas venting. Among the heavy metals tested, Cd had the strongest tendency to transfer during incineration (T{sub Cd} = 69.5%) because it had the lowest melting point, followed by Cu, Ni, Pb and Zn. The exchangeable and residual fractions of heavy metals increased substantially in the incineration products compared with that of the input residues. Although the mass of residues from WEEE dismantling can be reduced by 70% by incineration, the safe disposal of the metal-enriched bottom and fly ashes is still required.

Physico-chemical characterisation of material fractions in residual and source-segregated household waste in Denmark

DEFF Research Database (Denmark)

Götze, Ramona; Pivnenko, Kostyantyn; Boldrin, Alessio

2016-01-01

differences in the physico-chemical properties of residual and source-segregated waste fractions were found for many parameters related to organic matter, but also for elements of environmental concern. Considerable differences in potentially toxic metal concentrations between the individual recyclable......Physico-chemical waste composition data are paramount for the assessment and planning of waste management systems. However, the applicability of data is limited by the regional, temporal and technical scope of waste characterisation studies. As Danish and European legislation aims for higher...... recycling rates evaluation of source-segregation and recycling chains gain importance. This paper provides a consistent up-to-date dataset for 74 physico-chemical parameters in 49 material fractions from residual and 24 material fractions from source-segregated Danish household waste. Significant...

WASTE TREATMENT BUILDING SYSTEM DESCRIPTION DOCUMENT

Energy Technology Data Exchange (ETDEWEB)

F. Habashi

2000-06-22

The Waste Treatment Building System provides the space, layout, structures, and embedded subsystems that support the processing of low-level liquid and solid radioactive waste generated within the Monitored Geologic Repository (MGR). The activities conducted in the Waste Treatment Building include sorting, volume reduction, and packaging of dry waste, and collecting, processing, solidification, and packaging of liquid waste. The Waste Treatment Building System is located on the surface within the protected area of the MGR. The Waste Treatment Building System helps maintain a suitable environment for the waste processing and protects the systems within the Waste Treatment Building (WTB) from most of the natural and induced environments. The WTB also confines contaminants and provides radiological protection to personnel. In addition to the waste processing operations, the Waste Treatment Building System provides space and layout for staging of packaged waste for shipment, industrial and radiological safety systems, control and monitoring of operations, safeguards and security systems, and fire protection, ventilation and utilities systems. The Waste Treatment Building System also provides the required space and layout for maintenance activities, tool storage, and administrative facilities. The Waste Treatment Building System integrates waste processing systems within its protective structure to support the throughput rates established for the MGR. The Waste Treatment Building System also provides shielding, layout, and other design features to help limit personnel radiation exposures to levels which are as low as is reasonably achievable (ALARA). The Waste Treatment Building System interfaces with the Site Generated Radiological Waste Handling System, and with other MGR systems that support the waste processing operations. The Waste Treatment Building System interfaces with the General Site Transportation System, Site Communications System, Site Water System, MGR

WASTE TREATMENT BUILDING SYSTEM DESCRIPTION DOCUMENT

International Nuclear Information System (INIS)

Habashi, F.

2000-01-01

The Waste Treatment Building System provides the space, layout, structures, and embedded subsystems that support the processing of low-level liquid and solid radioactive waste generated within the Monitored Geologic Repository (MGR). The activities conducted in the Waste Treatment Building include sorting, volume reduction, and packaging of dry waste, and collecting, processing, solidification, and packaging of liquid waste. The Waste Treatment Building System is located on the surface within the protected area of the MGR. The Waste Treatment Building System helps maintain a suitable environment for the waste processing and protects the systems within the Waste Treatment Building (WTB) from most of the natural and induced environments. The WTB also confines contaminants and provides radiological protection to personnel. In addition to the waste processing operations, the Waste Treatment Building System provides space and layout for staging of packaged waste for shipment, industrial and radiological safety systems, control and monitoring of operations, safeguards and security systems, and fire protection, ventilation and utilities systems. The Waste Treatment Building System also provides the required space and layout for maintenance activities, tool storage, and administrative facilities. The Waste Treatment Building System integrates waste processing systems within its protective structure to support the throughput rates established for the MGR. The Waste Treatment Building System also provides shielding, layout, and other design features to help limit personnel radiation exposures to levels which are as low as is reasonably achievable (ALARA). The Waste Treatment Building System interfaces with the Site Generated Radiological Waste Handling System, and with other MGR systems that support the waste processing operations. The Waste Treatment Building System interfaces with the General Site Transportation System, Site Communications System, Site Water System, MGR

Identifying the key factors in increasing recycling and reducing residual household waste: a case study of the Flemish region of Belgium.

Science.gov (United States)

Gellynck, X; Jacobsen, R; Verhelst, P

2011-10-01

The competent waste authority in the Flemish region of Belgium created the 'Implementation plan household waste 2003-2007' and the 'Implementation plan sustainable management 2010-2015' to comply with EU regulation. It incorporates European and regional requirements and describes strategies, goals, actions and instruments for the collection and treatment of household waste. The central mandatory goal is to reduce and maintain the amount of residual household waste to 150 kg per capita per year between 2010-2015. In literature, a reasonable body of information has been published on the effectiveness and efficiency of a variety of policy instruments, but the information is complex, often contradictory and difficult to interpret. The objective of this paper is to identify, through the development of a binary logistic regression model, those variables of the waste collection scheme that help municipalities to reach the mandatory 150 kg goal. The model covers a number of variables for household characteristics, provision of recycling services, frequency of waste collection and charging for waste services. This paper, however, is not about waste prevention and reuse. The dataset originates from 2003. Four out of 12 variables in the model contributed significantly: income per capita, cost of residual waste collection, collection frequency and separate curbside collection of organic waste. Copyright © 2011 Elsevier Ltd. All rights reserved.

Waste treatment by microwave and electron beam irradiation

International Nuclear Information System (INIS)

Martin, D.; Craciun, G.; Manaila, E.; Ighigeanu, D; Oproiu, C.; Iacob, N.; Togoe, I.; Margaritescu, I.

2007-01-01

Comparative results obtained by applying separate and combined (successive and simultaneous) electron beam (EB) and microwave (MW) irradiation to waste treatment, such as food residuals (minced beef, wheat bran and wheat flour) and sewage sludge performed from a food industry wastewater treatment station (vegetable oil plant), are presented. The research results demonstrated that the simultaneous EB and MW irradiation produces the biggest reduction of microorganisms. The tests also demonstrated that the irradiation time and the upper limit of required EB absorbed dose, which ensures a complete sterilization effect, could be reduced by a factor of two by an additional use of MW energy to EB irradiation

Stabilization Using Phosphate Bonded Ceramics. Salt Containing Mixed Waste Treatment. Mixed Waste Focus Area. OST Reference No. 117

International Nuclear Information System (INIS)

1999-01-01

Throughout the Department of Energy (DOE) complex there are large inventories of homogeneous mixed waste solids, such as wastewater treatment residues, fly ashes, and sludges that contain relatively high concentrations (greater than 15% by weight) of salts. The inherent solubility of salts (e.g., nitrates, chlorides, and sulfates) makes traditional treatment of these waste streams difficult, expensive, and challenging. One alternative is low-temperature stabilization by chemically bonded phosphate ceramics (CBPCs). The process involves reacting magnesium oxide with monopotassium phosphate with the salt waste to produce a dense monolith. The ceramic makes a strong environmental barrier, and the metals are converted to insoluble, low-leaching phosphate salts. The process has been tested on a variety of surrogates and actual mixed waste streams, including soils, wastewater, flyashes, and crushed debris. It has also been demonstrated at scales ranging from 5 to 55 gallons. In some applications, the CBPC technology provides higher waste loadings and a more durable salt waste form than the baseline method of cementitious grouting. Waste form test specimens were subjected to a variety of performance tests. Results of waste form performance testing concluded that CBPC forms made with salt wastes meet or exceed both RCRA and recommended Nuclear Regulatory Commission (NRC) low-level waste (LLW) disposal criteria. Application of a polymer coating to the CBPC may decrease the leaching of salt anions, but continued waste form evaluations are needed to fully assess the deteriorating effects of this leaching, if any, over time.

Contaminant Release from Residual Waste in Closed Single-Shell Tanks and Other Waste Forms Associated with the Tanks

International Nuclear Information System (INIS)

Deutsch, William J.

2008-01-01

This chapter describes the release of contaminants from the various waste forms that are anticipated to be associated with closure of the single-shell tanks. These waste forms include residual sludge or saltcake that will remain in the tanks after waste retrieval. Other waste forms include engineered glass and cementitious materials as well as contaminated soil impacted by previous tank leaks. This chapter also describes laboratory testing to quantify contaminant release and how the release data are used in performance/risk assessments for the tank waste management units and the onsite waste disposal facilities. The chapter ends with a discussion of the surprises and lessons learned to date from the testing of waste materials and the development of contaminant release models

Analysis of waste treatment requirements for DOE mixed wastes: Technical basis

International Nuclear Information System (INIS)

1995-02-01

The risks and costs of managing DOE wastes are a direct function of the total quantities of 3wastes that are handled at each step of the management process. As part of the analysis of the management of DOE low-level mixed wastes (LLMW), a reference scheme has been developed for the treatment of these wastes to meet EPA criteria. The treatment analysis in a limited form was also applied to one option for treatment of transuranic wastes. The treatment requirements in all cases analyzed are based on a reference flowsheet which provides high level treatment trains for all LLMW. This report explains the background and basis for that treatment scheme. Reference waste stream chemical compositions and physical properties including densities were established for each stream in the data base. These compositions are used to define the expected behavior for wastes as they pass through the treatment train. Each EPA RCRA waste code was reviewed, the properties, chemical composition, or characteristics which are of importance to waste behavior in treatment were designated. Properties that dictate treatment requirements were then used to develop the treatment trains and identify the unit operations that would be included in these trains. A table was prepared showing a correlation of the waste physical matrix and the waste treatment requirements as a guide to the treatment analysis. The analysis of waste treatment loads is done by assigning wastes to treatment steps which would achieve RCRA compliant treatment. These correlation's allow one to examine the treatment requirements in a condensed manner and to see that all wastes and contaminant sets are fully considered

Biological treatment of concentrated hazardous, toxic, and radionuclide mixed wastes without dilution

International Nuclear Information System (INIS)

Stringfellow, William T.; Komada, Tatsuyuki; Chang, Li-Yang

2004-01-01

Approximately 10 percent of all radioactive wastes produced in the U. S. are mixed with hazardous or toxic chemicals and therefore can not be placed in secure land disposal facilities. Mixed wastes containing hazardous organic chemicals are often incinerated, but volatile radioactive elements are released directly into the biosphere. Some mixed wastes do not currently have any identified disposal option and are stored locally awaiting new developments. Biological treatment has been proposed as a potentially safer alternative to incineration for the treatment of hazardous organic mixed wastes, since biological treatment would not release volatile radioisotopes and the residual low-level radioactive waste would no longer be restricted from land disposal. Prior studies have shown that toxicity associated with acetonitrile is a significant limiting factor for the application of biotreatment to mixed wastes and excessive dilution was required to avoid inhibition of biological treatment. In this study, we demonstrate that a novel reactor configuration, where the concentrated toxic waste is drip-fed into a complete-mix bioreactor containing a pre-concentrated active microbial population, can be used to treat a surrogate acetonitrile mixed waste stream without excessive dilution. Using a drip-feed bioreactor, we were able to treat a 90,000 mg/L acetonitrile solution to less than 0.1 mg/L final concentration using a dilution factor of only 3.4. It was determined that the acetonitrile degradation reaction was inhibited at a pH above 7.2 and that the reactor could be modeled using conventional kinetic and mass balance approaches. Using a drip-feed reactor configuration addresses a major limiting factor (toxic inhibition) for the biological treatment of toxic, hazardous, or radioactive mixed wastes and suggests that drip-feed bioreactors could be used to treat other concentrated toxic waste streams, such as chemical warfare materiel

Treatment of solid waste highly contaminated by alpha emitters low-temperature impact crushing/leaching and incineration

International Nuclear Information System (INIS)

Carpentier, S.; Bertolotti, G.

1986-01-01

Reprocessing plants, hot laboratories, fuel fabrication plants all produce waste containing residual quantities of plutonium and uranium in oxide form which often reach some tens of grammes per m 3 . Appropriate treatment recovers an appreciable amount of fissile material, which could lead to the waste being declassified and able to be disposed of in near ground-level facilities. After a summary sorting at production level, waste can be sent to a low-temperature impact crushing/leaching unit which considerably reduces volumes to be stored. We call this process cryo-crushing/leaching. For burnable crushed particles, a further volume reduction may be obtained by incineration, an operation which is made easier by the low fissile material residue content. Incineration can, of course also be applied directly to burnable solid waste sorted at source and crushed following more conventional methods [fr

Integrated gasification and plasma cleaning for waste treatment: A life cycle perspective

International Nuclear Information System (INIS)

Evangelisti, Sara; Tagliaferri, Carla; Clift, Roland; Lettieri, Paola; Taylor, Richard; Chapman, Chris

2015-01-01

Highlights: • A life cycle assessment of an advanced two-stage process is undertaken. • A comparison of the impacts of the process when fed with 7 feedstock is presented. • Sensitivity analysis on the system is performed. • The treatment of RDF shows the lowest impact in terms of both GWP and AP. • The plasma shows a small contribution to the overall impact of the plant. - Abstract: In the past, almost all residual municipal waste in the UK was landfilled without treatment. Recent European waste management directives have promoted the uptake of more sustainable treatment technologies, especially for biodegradable waste. Local authorities have started considering other options for dealing with residual waste. In this study, a life cycle assessment of a future 20 MWe plant using an advanced two-stage gasification and plasma technology is undertaken. This plant can thermally treat waste feedstocks with different composition and heating value to produce electricity, steam and a vitrified product. The objective of the study is to analyse the environmental impacts of the process when fed with seven different feedstocks (including municipal solid waste, solid refuse fuel, reuse-derived fuel, wood biomass and commercial & industrial waste) and identify the process steps which contribute more to the environmental burden. A scenario analysis on key processes, such as oxygen production technology, metal recovery and the appropriate choice for the secondary market aggregate material, is performed. The influence of accounting for the biogenic carbon content in the waste from the calculations of the global warming potential is also shown. Results show that the treatment of the refuse-derived fuel has the lowest impact in terms of both global warming potential and acidification potential because of its high heating value. For all the other impact categories analysed, the two-stage gasification and plasma process shows a negative impact for all the waste streams

Integrated gasification and plasma cleaning for waste treatment: A life cycle perspective

Energy Technology Data Exchange (ETDEWEB)

Evangelisti, Sara [Chemical Engineering Department, University College London, Torrington Place, London WC1E 7JE (United Kingdom); Tagliaferri, Carla [Chemical Engineering Department, University College London, Torrington Place, London WC1E 7JE (United Kingdom); Advanced Plasma Power (APP), Unit B2, Marston Gate, South Marston Business Park, Swindon SN3 4DE (United Kingdom); Clift, Roland [Centre for Environmental Strategy, The University of Surrey, Guildford, Surrey GU2 7XH (United Kingdom); Lettieri, Paola, E-mail: p.lettieri@ucl.ac.uk [Chemical Engineering Department, University College London, Torrington Place, London WC1E 7JE (United Kingdom); Taylor, Richard; Chapman, Chris [Advanced Plasma Power (APP), Unit B2, Marston Gate, South Marston Business Park, Swindon SN3 4DE (United Kingdom)

2015-09-15

Highlights: • A life cycle assessment of an advanced two-stage process is undertaken. • A comparison of the impacts of the process when fed with 7 feedstock is presented. • Sensitivity analysis on the system is performed. • The treatment of RDF shows the lowest impact in terms of both GWP and AP. • The plasma shows a small contribution to the overall impact of the plant. - Abstract: In the past, almost all residual municipal waste in the UK was landfilled without treatment. Recent European waste management directives have promoted the uptake of more sustainable treatment technologies, especially for biodegradable waste. Local authorities have started considering other options for dealing with residual waste. In this study, a life cycle assessment of a future 20 MWe plant using an advanced two-stage gasification and plasma technology is undertaken. This plant can thermally treat waste feedstocks with different composition and heating value to produce electricity, steam and a vitrified product. The objective of the study is to analyse the environmental impacts of the process when fed with seven different feedstocks (including municipal solid waste, solid refuse fuel, reuse-derived fuel, wood biomass and commercial & industrial waste) and identify the process steps which contribute more to the environmental burden. A scenario analysis on key processes, such as oxygen production technology, metal recovery and the appropriate choice for the secondary market aggregate material, is performed. The influence of accounting for the biogenic carbon content in the waste from the calculations of the global warming potential is also shown. Results show that the treatment of the refuse-derived fuel has the lowest impact in terms of both global warming potential and acidification potential because of its high heating value. For all the other impact categories analysed, the two-stage gasification and plasma process shows a negative impact for all the waste streams

Surrogate formulations for thermal treatment of low-level mixed waste, Part II: Selected mixed waste treatment project waste streams

Energy Technology Data Exchange (ETDEWEB)

Bostick, W.D.; Hoffmann, D.P.; Chiang, J.M.; Hermes, W.H.; Gibson, L.V. Jr.; Richmond, A.A. [Martin Marietta Energy Systems, Inc., Oak Ridge, TN (United States); Mayberry, J. [Science Applications International Corp., Idaho Falls, ID (United States); Frazier, G. [Univ. of Tennessee, Knoxville, TN (United States)

1994-01-01

This report summarizes the formulation of surrogate waste packages, representing the major bulk constituent compositions for 12 waste stream classifications selected by the US DOE Mixed Waste Treatment Program. These waste groupings include: neutral aqueous wastes; aqueous halogenated organic liquids; ash; high organic content sludges; adsorbed aqueous and organic liquids; cement sludges, ashes, and solids; chloride; sulfate, and nitrate salts; organic matrix solids; heterogeneous debris; bulk combustibles; lab packs; and lead shapes. Insofar as possible, formulation of surrogate waste packages are referenced to authentic wastes in inventory within the DOE; however, the surrogate waste packages are intended to represent generic treatability group compositions. The intent is to specify a nonradiological synthetic mixture, with a minimal number of readily available components, that can be used to represent the significant challenges anticipated for treatment of the specified waste class. Performance testing and evaluation with use of a consistent series of surrogate wastes will provide a means for the initial assessment (and intercomparability) of candidate treatment technology applicability and performance. Originally the surrogate wastes were intended for use with emerging thermal treatment systems, but use may be extended to select nonthermal systems as well.

Surrogate formulations for thermal treatment of low-level mixed waste, Part II: Selected mixed waste treatment project waste streams

International Nuclear Information System (INIS)

Bostick, W.D.; Hoffmann, D.P.; Chiang, J.M.; Hermes, W.H.; Gibson, L.V. Jr.; Richmond, A.A.; Mayberry, J.; Frazier, G.

1994-01-01

This report summarizes the formulation of surrogate waste packages, representing the major bulk constituent compositions for 12 waste stream classifications selected by the US DOE Mixed Waste Treatment Program. These waste groupings include: neutral aqueous wastes; aqueous halogenated organic liquids; ash; high organic content sludges; adsorbed aqueous and organic liquids; cement sludges, ashes, and solids; chloride; sulfate, and nitrate salts; organic matrix solids; heterogeneous debris; bulk combustibles; lab packs; and lead shapes. Insofar as possible, formulation of surrogate waste packages are referenced to authentic wastes in inventory within the DOE; however, the surrogate waste packages are intended to represent generic treatability group compositions. The intent is to specify a nonradiological synthetic mixture, with a minimal number of readily available components, that can be used to represent the significant challenges anticipated for treatment of the specified waste class. Performance testing and evaluation with use of a consistent series of surrogate wastes will provide a means for the initial assessment (and intercomparability) of candidate treatment technology applicability and performance. Originally the surrogate wastes were intended for use with emerging thermal treatment systems, but use may be extended to select nonthermal systems as well

Development of treatment method for stillage residues of liquid radioactive wastes to remove organic substances and transuranium elements

International Nuclear Information System (INIS)

Rudenko, L.I.; Dzhuzha, O.V.; Khan, V.E.

2008-01-01

The paper presents the results of the study into the laws that govern the process of treating by oxidation the stillage residues of liquid radioactive wastes to remove organic compounds and transuranium elements with the use of hydrogen peroxide, potassium permanganate and subsequent ultra-filtration. The optimum oxidisation regime has been defined on the basis of this study to ensure that the initial dichromate oxidability of LRW's stillage residues decreases from 6,000-9,500 to 500-1,000 mg O/I, whereas the TUE activity associated with the key isotopes is reduced by 74-87 % for 238,239,240 Pu, by 94-95 % for 241 Am, and by 90-95 % for 244 Cm. The concentration of uranium decreases by 94-99 %. It is proposed to implement this method at the Chernobyl NPP site.

Assessment of residual DDE at four remediated Hanford waste sites, Richland, Washington

International Nuclear Information System (INIS)

Linville, J.K.

1999-01-01

The objectives of this study were to determine the extent and distribution of residual DDE, a metabolite of dichlorodiphenyltrichloroethane (DDT), across the four waste sites by sampling ground-dwelling insects and bird eggs, evaluating the use of insects for monitoring contamination pathways, and determining the species of passerine birds present and the number of nesting pairs utilizing the waste sites

40 CFR Appendix Vii to Part 266 - Health-Based Limits for Exclusion of Waste-Derived Residues*

Science.gov (United States)

2010-07-01

... Waste-Derived Residues* VII Appendix VII to Part 266 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES (CONTINUED) STANDARDS FOR THE MANAGEMENT OF SPECIFIC HAZARDOUS WASTES AND SPECIFIC TYPES OF HAZARDOUS WASTE MANAGEMENT FACILITIES Pt. 266, App. VII Appendix VII to Part 266—Health...

Stabilization of organic matter and nitrogen immobilization during mechanical-biological treatment and landfilling of residual municipal solid waste

International Nuclear Information System (INIS)

Heiss-Ziegler, C.

2000-04-01

Synthesis of humic substances and nitrogen immobilization during mechanical-biological treatment of waste and the behavior of biologically stabilized waste under anaerobic landfill conditions were investigated. Samples were taken from a large-scale treatment plant. Anaerobic conditions were simulated in lab scale test cells. Humic substances were analyzed photometrically and gravimetrically. The nitrogen immobilization was investigated by sequential leaching tests and by analyzing the non acid hydrolyzable nitrogen. Humic acids were mainly synthesized during the beginning of the intensive rotting phase. Later on in the process no significant changes occurred. The humic acid content rose up to 6,8 % DS org. It correlated well with the stability parameters respiration activity and accumulated gas production. In the coarse of the treatment the nitrogen load emitted during the consecutive leaching tests dropped from 50 % down to less than 20 % total nitrogen. The non acid hydrolyzable nitrogen rose from 17 up to 42 % Kjeldahl nitrogen content. Nevertheless the mechanical-biological treatment is not significantly shortening the aftercare period of a landfill concerning liquid nitrogen emissions. The reduced nitrogen emission potential is released more slowly. When reactive waste material was exposed to anaerobic conditions, humic and fulvic acids were synthesized up to the point when intensive gas production started and then were remineralized. Stabilized waste materials after treatment of various intensity behaved differently under anaerobic conditions. Steady and decreasing humic acid contents were observed. (author)

Treatment of the acid mine drainage residue for uranium recovery

International Nuclear Information System (INIS)

Dias, M.M.; Horta, D.G.; Fukuma, H.T.; Villegas, R.A.S.; Carvalho, C.H.T. de; Silva, A.C. da

2017-01-01

Acid mine drainage (AMD) is a process that occurs in many mining that have sulfide ores. With water and oxygen, several metals are oxidized, one example being uranium. At the mine pit of the Osamu Utsumi Mine located at INB - Caldas and in two other boot-wastes (mining waste pile), AMD is present and currently, without a technological solution. The acidic water present in the pit is treated with hydrated lime, generating water for disposal and an alkaline residue called calcium diuranate - DUCA. The DUCA has a concentration of approximately 0.32% U 3 O 8 , which makes interesting the development of a process for extracting that metal. One of the processes that can be used is leaching. For this study, it was decided to evaluate the alkaline leaching to extract the uranium present in the residue. It is necessary to optimize operational parameters for the process: percentage of solids, concentration of leaching agent in solution, temperature and reaction time. With these parameters, it is possible to improve the leaching so that the largest amount of uranium is extracted from the sample, to help solve the environmental impact caused by the wastewater from the treatment of acid waters and, in addition, to give an economical destination for this metal that is contained in the deposited DUCA

MWIP: Surrogate formulations for thermal treatment of low-level mixed waste

International Nuclear Information System (INIS)

Bostick, W.D.; Hoffmann, D.P.; Stevenson, R.J.; Richmond, A.A.; Bickford, D.F.

1994-01-01

The category of sludges, filter cakes, and other waste processing residuals represent the largest volume of low-level mixed (hazardous and radioactive) wastes within the US Department of Energy (DOE) complex. Treatment of these wastes to minimize the mobility of contaminants, and to eliminate the presence of free water, is required under the Federal Facility Compliance Act agreements between DOE and the Environmental Protection Agency. In the text, we summarize the currently available data for several of the high priority mixed-waste sludge inventories within DOE. Los Alamos National Laboratory TA-50 Sludge and Rocky Flats Plant By-Pass Sludge are transuranic (TRU)-contaminated sludges that were isolated with the use of silica-based filter aids. The Oak Ridge Y-12 Plant West End Treatment Facility Sludge is predominantly calcium carbonate and biomass. The Oak Ridge K-25 Site Pond Waste is a large-volume waste stream, containing clay, silt, and other debris in addition to precipitated metal hydroxides. We formulate ''simulants'' for the waste streams described above, using cerium oxide as a surrogate for the uranium or plutonium present in the authentic material. Use of nonradiological surrogates greatly simplifies material handling requirements for initial treatability studies. The use of synthetic mixtures for initial treatability testing will facilitate compositional variation for use in conjunction with statistical design experiments; this approach may help to identify any ''operating window'' limitations. The initial treatability testing demonstrations utilizing these ''simulants'' will be based upon vitrification, although the materials are also amenable to testing grout-based and other stabilization procedures. After the feasibility of treatment and the initial evaluation of treatment performance has been demonstrated, performance must be verified using authentic samples of the candidate waste stream

Stabilization of in-tank residual wastes and external-tank soil contamination for the tank focus area, Hanford tank initiative: Applications to the AX Tank Farm

International Nuclear Information System (INIS)

Balsley, S.D.; Krumhansl, J.L.; Borns, D.J.; McKeen, R.G.

1998-07-01

A combined engineering and geochemistry approach is recommended for the stabilization of waste in decommissioned tanks and contaminated soils at the AX Tank Farm, Hanford, WA. A two-part strategy of desiccation and gettering is proposed for treatment of the in-tank residual wastes. Dry portland cement and/or fly ash are suggested as an effective and low-cost desiccant for wicking excess moisture from the upper waste layer. Getters work by either ion exchange or phase precipitation to reduce radionuclide concentrations in solution. The authors recommend the use of specific natural and man-made compounds, appropriately proportioned to the unique inventory of each tank. A filler design consisting of multilayered cementitous grout with interlayered sealant horizons should serve to maintain tank integrity and minimize fluid transport to the residual waste form. External tank soil contamination is best mitigated by placement of grouted skirts under and around each tank, together with installation of a cone-shaped permeable reactive barrier beneath the entire tank farm. Actinide release rates are calculated from four tank closure scenarios ranging from no action to a comprehensive stabilization treatment plan (desiccant/getters/grouting/RCRA cap). Although preliminary, these calculations indicate significant reductions in the potential for actinide transport as compared to the no-treatment option

Treatment of Lagoon sludge waste generated from Uranium Conversion Plant

International Nuclear Information System (INIS)

Hwang, D.S.; Oh, J.H.; Lee, K.I.; Choi, Y.D.; Hwang, S.T.; Park, J.H.

2003-01-01

This study investigated the dissolution property of nitrate salts in the desalination process by water and the drying property of residual solid after separating nitrates in a series of processes for the sludge treatment. Desalination was carried out with the adding ratio of water and drying property was analyzed by TG/DTA, FTIR, and XRD. Nitrate salts involved in the sludge were separated over 97 % at the water adding ratio of 2.5. But a small quantity of calcium and sodium nitrate remained in the residue. These were decomposed over 600 deg. C while calcium carbonate, which was a main compound of residual solid, was decomposed into calcium oxide over 750 deg. C. The residual solid has to be decomposed over 800 deg. C to converse uranyl nitrate of six values into the stable U 3 O 8 of four values. As a result of removing the nitrates at the adding ratio of 2.5 and drying the residue over 900 deg. C, volume of the sludge waste decreased over 80 %. (authors)

Metal waste forms from treatment of EBR-II spent fuel

International Nuclear Information System (INIS)

Abraham, D. P.

1998-01-01

Demonstration of Argonne National Laboratory's electrometallurgical treatment of spent nuclear fuel is currently being conducted on irradiated, metallic driver fuel and blanket fuel elements from the Experimental Breeder Reactor-II (EBR-II) in Idaho. The residual metallic material from the electrometallurgical treatment process is consolidated into an ingot, the metal waste form (MWF), by employing an induction furnace in a hot cell. Scanning electron microscopy (SEM) and chemical analyses have been performed on irradiated cladding hulls from the driver fuel, and on samples from the alloy ingots. This paper presents the microstructures of the radioactive ingots and compares them with observations on simulated waste forms prepared using non-irradiated material. These simulated waste forms have the baseline composition of stainless steel - 15 wt % zirconium (SS-15Zr). Additions of noble metal elements, which serve as surrogates for fission products, and actinides are made to that baseline composition. The partitioning of noble metal and actinide elements into alloy phases and the role of zirconium for incorporating these elements is discussed in this paper

Incinerator performance: effects of changes in waste input and furnace operation on air emissions and residues

DEFF Research Database (Denmark)

Astrup, Thomas; Riber, Christian; Pedersen, Anne Juul

2011-01-01

Waste incineration can be considered a robust technology for energy recovery from mixed waste. Modern incinerators are generally able to maintain relatively stable performance, but changes in waste input and furnace operation may affect emissions. This study investigated how inorganic air emissions...... including ‘as-large-as-possible’ changes in furnace operation (oxygen levels, air supply and burnout level) only using normal MSW as input. The experiments showed that effects from the added waste materials were significant in relation to: air emissions (in particular As, Cd, Cr, Hg, Sb), element transfer...... coefficients, and residue composition (As, Cd, Cl, Cr, Cu, Hg, Mo, Ni, Pb, S, Sb, Zn). Changes in furnace operation could not be directly linked to changes in emissions and residues. The results outlined important elements in waste which should be addressed in relation to waste incinerator performance. Likely...

The newest achievements of studies on the reutilization, treatment, and disposal technology of hazardous wastes

Energy Technology Data Exchange (ETDEWEB)

Liu Peizhe [Chinese Research Academy of Environmental Sciences, Beijing (China)

1996-12-31

From 1991 to 1996, key studies on the reutilization, treatment, and disposal technology of hazardous wastes have been incorporated into the national plan for environmental protection science and technology. At present, the research achievements have been accomplished, have passed national approval, and have been accepted. The author of this paper, as leader of the national group for this research work, expounds the newest achievements of the studies involving four parts: (1) the reutilization technology of electroplating sludge, including the ion-exchange process for recovering the sludge and waste liquor for producing chromium tanning agent and extracting chromium and colloidal protein from tanning waste residue; on the recovery of heavy metals from the electroplating waste liquor with microbic purification; on the demonstration project of producing modified plastics from the sludge and the waste plastics; and on the demonstration of the recovery of heavy metals from waste electroplating sludge by using the ammonia-leaching process; (2) the demonstrative research of reutilization technology of chromium waste residues, including production of self-melting ore and smelting of chromium-containing pig iron, and of pyrolytic detoxification of the residue with cyclone furnace; (3) the incineration technology of hazardous wastes with successful results of the industrial incinerator system for polychlorinated biphenyls; and (4) the safety landfill technology for disposal of hazardous wastes, with a complete set of technology for pretreatment, selection of the site, development of the antipercolating materials, and design and construction of the landfill. Only a part of the achievements is introduced in this paper, most of which has been built and is being operated for demonstration to further spreading application and accumulate experience. 6 refs., 7 figs., 6 tabs.

SECONDARY WASTE MANAGEMENT STRATEGY FOR EARLY LOW ACTIVITY WASTE TREATMENT

Energy Technology Data Exchange (ETDEWEB)

TW, CRAWFORD

2008-07-17

This study evaluates parameters relevant to River Protection Project secondary waste streams generated during Early Low Activity Waste operations and recommends a strategy for secondary waste management that considers groundwater impact, cost, and programmatic risk. The recommended strategy for managing River Protection Project secondary waste is focused on improvements in the Effiuent Treatment Facility. Baseline plans to build a Solidification Treatment Unit adjacent to Effluent Treatment Facility should be enhanced to improve solid waste performance and mitigate corrosion of tanks and piping supporting the Effiuent Treatment Facility evaporator. This approach provides a life-cycle benefit to solid waste performance and reduction of groundwater contaminants.

Development of ecologically safety technology for steam-thermal treatment of organic wastes

International Nuclear Information System (INIS)

Juravskij, J.

1997-01-01

The experience on mitigation of the consequences of the Chernobyl's nuclear power station accident proves that the treatment of large amounts of organic and mixed wastes containing radionuclides is a very urgent scientific and technical problem. In this connection a search for new ideas and development of highly efficient and ecologically safety technologies for treatment of organic radioactive wastes has been undertaken. This study is based on use of physico-mechanical properties of various organic materials (wood, rubber-containing composites, plastics, biomass) subjected to thermal decomposition in the overheated water steam medium. Under such conditions, there is a possibility, under relatively low temperatures (400 - 500 deg. C), to realize thermal decomposition and considerably (in 8 - 50 times) to reduce the amount of wastes, to obtain the main concentration of radionuclides in the solid residue and to prevent releases of gaseous products containing radionuclides to the environment. (author). 5 figs, 1 tab

Treatment of solid non-active wastes

International Nuclear Information System (INIS)

Chmielewska, E.

2008-01-01

In this part of the text-book treatment of solid non-active wastes is described. This part consist of following chapters: (1) Law on wastes; (2) Present situation in waste management; (3) Strategic tendencies of waste management; (4) Incineration (disposal of solid wastes); (5) Disposal; (6) Composting; (7) Treatment of sludge from sewage clarification plant; (8) Biodegradation; (9) Recycling of wastes (assessing of secondary raw materials). Legal aspects of treatment of solid non-active wastes is presented

Electrodialytic removal of heavy metals and chloride from municipal solid waste incineration fly ash and air pollution control residue in suspension - test of a new two compartment experimental cell

DEFF Research Database (Denmark)

Kirkelund, Gunvor Marie; Magro, Cátia; Guedes, Paula

2015-01-01

Municipal solid waste incineration (MSWI) residues such as fly ash and air pollution control (APC) residues are classified as hazardous waste and disposed of, although they contain potential resources. The most problematic elements in MSWI residues are leachable heavy metals and salts. For reuse...... of MSWI residues in for instance concrete, the aim of remediation should be reduction of the heavy metal leaching, while at the same time keeping the alkaline pH, so the residue can replace cement. In this study a MSWI residues were subjected to electrodialytic remediation under various experimental...... heavy metal leaching except when the pH was reduced to a level below 8 for the fly ash. On the other hand, Cr leaching increased by the electrodialytic treatment. Cl leaching from the MSWI residues was less dependent on experimental conditions and was reduced in all experiments compared to the initial...

Climate accounting for waste management, Phase I and II. Summary: Phase 1: Glass Packaging, Metal packaging, paper, cardboard, plastic and wet organic waste. Phase 2: Wood waste and residual waste from households; Klimaregnskap for avfallshaandtering, Fase I og II. Sammendrag: Fase 1: Glassemballasje, metallemballasje, papir, papp, plastemballasje og vaatorganisk avfall. Fase 2: Treavfall og restavfall fra husholdninger

Energy Technology Data Exchange (ETDEWEB)

Raadal, Hanne Lerche; Modahl, Ingunn Saur; Lyng, Kari-Anne

2009-09-15

Background. On the basis of an increased focus on emissions of greenhouse gases in general, Waste Norway wanted to prepare a climate accounting for waste management in Norway. Oestfoldforskning was engaged to undertake the project. The aim of the project has been to develop a model for the calculation of net greenhouse gas emissions from different waste types of waste glass containers, metal containers, paper, cardboard, plastic, wet organic waste, wood waste and residual waste. The model is based on life cycle methodology and is used to calculate the net greenhouse gas emissions per kg of waste for the various waste management options and waste types, as well as to calculate the net greenhouse gas emissions for waste management for including waste types and quantities of 2006. There is an emphasis on developing a model so that municipalities / waste companies or regions can develop their own climate accounting for waste management in their region, based on site-specific conditions associated with types and amounts of waste, transport distances, type of treatment, exploitation and use of waste generated energy etc. The model can also be used as the basis for the preparation of useful documentation as the basis for information about waste systems utility in general, and as a basis for strategic reviews for Waste Norway and the waste sector in particular. Conclusions: The main conclusions from the project can be summarized as follows: 1. The results of the study clearly shows that to consider only one environmental indicator is too narrow approach to form the basis for decision making for selection of waste management solutions. 2. Net greenhouse gas emissions for waste management varies greatly, both between the different types of waste and treatment methods which are reviewed. The main results of the ranking of management methods in relation to the net greenhouse effect associated with the waste types and treatment methods are as follows: Recycling of materials

Resource recovery from residual household waste: An application of exergy flow analysis and exergetic life cycle assessment

DEFF Research Database (Denmark)

Laner, David; Rechberger, Helmut; De Soete, Wouter

2015-01-01

Exergy is based on the Second Law of thermodynamics and can be used to express physical and chemical potential and provides a unified measure for resource accounting. In this study, exergy analysis was applied to four residual household waste management scenarios with focus on the achieved resource...... of the waste treatment system under investigation and (ii) exergetic life cycle assessment (LCA) using the Cumulative Exergy Extraction from the Natural Environment (CEENE) as a method for resource accounting. Scenario efficiencies of around 17-27% were found based on the exergy flow analysis (higher...... with the functionality of a material. In addition, the definition of appropriate waste system boundaries is critical for the exergy efficiencies derived from the flow analysis, as it is constrained by limited information available about the composition of flows in the system as well as about secondary production...

Engineering development and demonstration of DETOXSM wet oxidation for mixed waste treatment

International Nuclear Information System (INIS)

Dhooge, P.M.; Goldblatt, S.D.; Moslander, J.E.; Robertson, D.T.; Rogers, T.W.; Zigmond, J.A.

1997-12-01

DETOX SM , a catalyzed chemical oxidation process, is under development for treatment of hazardous and mixed wastes at Department of Energy sites. To support this effort, developmental engineering studies have been formed for aspects of the process to help ensure safe and effective operation. Subscale agitation studies have been preformed to identify a suitable mixing head and speed for the primary reaction vessel agitator. Mechanisms for feeding solid waste materials to the primary reaction vessel have been investigated. Filtration to remove solid field process residue, and the use of various filtration aids, has been studied. Extended compatibility studies on the materials of construction have been performed. Due to a change to Rocky Flats Environmental Technology Site (RFETS) for the mixed waste portion of the demonstration, types of wastes suitable and appropriate for treatment at RFETS had to be chosen. A Prototype unit has been fabricated and will be demonstrated on hazardous and mixed wastes at Savannah River Site (SRS) and RFETS during 1997 and 1998. The unit is in shakedown testing at present. Data validation and an engineering evaluation will be performed during the demonstration

Management of industrial solid residues; Gerenciamento de residuos solidos industriais

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-07-01

This chapter gives an overview on the management of industrial solid wastes, approaching the following subjects: classification of industrial solid residues; directives and methodologies for the management of industrial solid residues; instruments for the management of industrial solid residues; handling, packing, storage and transportation; treatment of industrial solid residues; final disposal - landfill for industrial residues; the problem of treatment and final disposer of domestic garbage in Brazil; recycling of the lubricant oils used in brazil; legislation.

Treatment of high-level wastes from the IFR fuel cycle

International Nuclear Information System (INIS)

Johnson, T.R.; Lewis, M.A.; Newman, A.E.; Laidler, J.J.

1992-01-01

The Integral Fast Reactor (IFR) is being developed as a future commercial power source that promises to have important advantages over present reactors, including improved resource conservation and waste management. The spent metal alloy fuels from an IFR will be processed in an electrochemical cell operating at 500 degree C with a molten chloride salt electrolyte and cadmium metal anode. After the actinides have been recovered from several batches of core and blanket fuels, the salt cadmium in this electrorefiner will be treated to separate fission products from residual transuranic elements. This treatment produces a waste salt that contains the alkali metal, alkaline earth, and halide fission products; some of the rare earths; and less than 100 nCi/g of alpha activity. The treated metal wastes contain the rest of the fission products (except T, Kr, and Xe) small amounts of uranium, and only trace amounts of transuranic elements. The current concept for the salt waste form is an aluminosilicate matrix, and the concept for the metal waste form is a corrosion-resistant metal alloy. The processes and equipment being developed to treat and immobilize the salt and metal wastes are described

Treatment of high-level wastes from the IFR fuel cycle

Energy Technology Data Exchange (ETDEWEB)

Johnson, T.R.; Lewis, M.A.; Newman, A.E.; Laidler, J.J.

1992-01-01

The Integral Fast Reactor (IFR) is being developed as a future commercial power source that promises to have important advantages over present reactors, including improved resource conservation and waste management. The spent metal alloy fuels from an IFR will be processed in an electrochemical cell operating at 500{degree}C with a molten chloride salt electrolyte and cadmium metal anode. After the actinides have been recovered from several batches of core and blanket fuels, the salt cadmium in this electrorefiner will be treated to separate fission products from residual transuranic elements. This treatment produces a waste salt that contains the alkali metal, alkaline earth, and halide fission products; some of the rare earths; and less than 100 nCi/g of alpha activity. The treated metal wastes contain the rest of the fission products (except T, Kr, and Xe) small amounts of uranium, and only trace amounts of transuranic elements. The current concept for the salt waste form is an aluminosilicate matrix, and the concept for the metal waste form is a corrosion-resistant metal alloy. The processes and equipment being developed to treat and immobilize the salt and metal wastes are described.

Treatment of high-level wastes from the IFR fuel cycle

Energy Technology Data Exchange (ETDEWEB)

Johnson, T.R.; Lewis, M.A.; Newman, A.E.; Laidler, J.J.

1992-08-01

The Integral Fast Reactor (IFR) is being developed as a future commercial power source that promises to have important advantages over present reactors, including improved resource conservation and waste management. The spent metal alloy fuels from an IFR will be processed in an electrochemical cell operating at 500{degree}C with a molten chloride salt electrolyte and cadmium metal anode. After the actinides have been recovered from several batches of core and blanket fuels, the salt cadmium in this electrorefiner will be treated to separate fission products from residual transuranic elements. This treatment produces a waste salt that contains the alkali metal, alkaline earth, and halide fission products; some of the rare earths; and less than 100 nCi/g of alpha activity. The treated metal wastes contain the rest of the fission products (except T, Kr, and Xe) small amounts of uranium, and only trace amounts of transuranic elements. The current concept for the salt waste form is an aluminosilicate matrix, and the concept for the metal waste form is a corrosion-resistant metal alloy. The processes and equipment being developed to treat and immobilize the salt and metal wastes are described.

Thermal treatment of organic radioactive waste

International Nuclear Information System (INIS)

Chrubasik, A.; Stich, W.

1993-01-01

The organic radioactive waste which is generated in nuclear and isotope facilities (power plants, research centers and other) must be treated in order to achieve a waste form suitable for long term storage and disposal. Therefore the resulting waste treatment products should be stable under influence of temperature, time, radioactivity, chemical and biological activity. Another reason for the treatment of organic waste is the volume reduction with respect to the storage costs. For different kinds of waste, different treatment technologies have been developed and some are now used in industrial scale. The paper gives process descriptions for the treatment of solid organic radioactive waste of low beta/gamma activity and alpha-contaminated solid organic radioactive waste, and the pyrolysis of organic radioactive waste

Low-level-waste-treatment handbook

International Nuclear Information System (INIS)

Clinton, S.D.; Goeller, H.E.; Holladay, D.W.; Donaldson, T.L.

1982-01-01

The initial draft of the Low-Level Waste Treatment Handbook has been prepared and submitted to the DOE Low-Level Waste Management Program for review and comment. A revised draft is scheduled to be delivered to DOE Headquarters in December 1982. The Handbook is designed to be useful to all individuals and groups concerned with low-level wastes. It is one of several volumes that will ultimately comprise a Low-Level Waste Technology Handbook. The objective of the Low-Level Waste Treatment Handbook is to present an overview of current practices related to the segregation, classification, volume reduction, solidification, handling, packaging, and transportation of LLW for disposal in a shallow land burial facility. The Handbook is intended to serve as a guide to individuals interested in the treatment and handling of low-level radioactive waste. The Handbook will not explicitly tell the user how to design and operate LLW treatment facilities, but rather will identify (1) kinds of information required to evaluate the options, (2) methods that may be used to evaluate these options, and (3) limitations associated with the selection of the treatment options. The focus of the Handbook is providing guidance on how to do waste treatment for disposal by shallow land burial

Environmental impacts of residual Municipal Solid Waste incineration: A comparison of 110 French incinerators using a life cycle approach

Energy Technology Data Exchange (ETDEWEB)

Beylot, Antoine, E-mail: a.beylot@brgm.fr; Villeneuve, Jacques

2013-12-15

Highlights: • 110 French incinerators are compared with LCA based on plant-specific data. • Environmental impacts vary as a function of plants energy recovery and NO{sub x} emissions. • E.g. climate change impact ranges from −58 to 408 kg CO{sub 2}-eq/tonne of residual MSW. • Implications for LCA of waste management in a decision-making process are detailed. - Abstract: Incineration is the main option for residual Municipal Solid Waste treatment in France. This study compares the environmental performances of 110 French incinerators (i.e. 85% of the total number of plants currently in activity in France) in a Life Cycle Assessment perspective, considering 5 non-toxic impact categories: climate change, photochemical oxidant formation, particulate matter formation, terrestrial acidification and marine eutrophication. Mean, median and lower/upper impact potentials are determined considering the incineration of 1 tonne of French residual Municipal Solid Waste. The results highlight the relatively large variability of the impact potentials as a function of the plant technical performances. In particular, the climate change impact potential of the incineration of 1 tonne of waste ranges from a benefit of −58 kg CO{sub 2}-eq to a relatively large burden of 408 kg CO{sub 2}-eq, with 294 kg CO{sub 2}-eq as the average impact. Two main plant-specific parameters drive the impact potentials regarding the 5 non-toxic impact categories under study: the energy recovery and delivery rate and the NO{sub x} process-specific emissions. The variability of the impact potentials as a function of incinerator characteristics therefore calls for the use of site-specific data when required by the LCA goal and scope definition phase, in particular when the study focuses on a specific incinerator or on a local waste management plan, and when these data are available.

Environmental impacts of residual Municipal Solid Waste incineration: A comparison of 110 French incinerators using a life cycle approach

International Nuclear Information System (INIS)

Beylot, Antoine; Villeneuve, Jacques

2013-01-01

Highlights: • 110 French incinerators are compared with LCA based on plant-specific data. • Environmental impacts vary as a function of plants energy recovery and NO x emissions. • E.g. climate change impact ranges from −58 to 408 kg CO 2 -eq/tonne of residual MSW. • Implications for LCA of waste management in a decision-making process are detailed. - Abstract: Incineration is the main option for residual Municipal Solid Waste treatment in France. This study compares the environmental performances of 110 French incinerators (i.e. 85% of the total number of plants currently in activity in France) in a Life Cycle Assessment perspective, considering 5 non-toxic impact categories: climate change, photochemical oxidant formation, particulate matter formation, terrestrial acidification and marine eutrophication. Mean, median and lower/upper impact potentials are determined considering the incineration of 1 tonne of French residual Municipal Solid Waste. The results highlight the relatively large variability of the impact potentials as a function of the plant technical performances. In particular, the climate change impact potential of the incineration of 1 tonne of waste ranges from a benefit of −58 kg CO 2 -eq to a relatively large burden of 408 kg CO 2 -eq, with 294 kg CO 2 -eq as the average impact. Two main plant-specific parameters drive the impact potentials regarding the 5 non-toxic impact categories under study: the energy recovery and delivery rate and the NO x process-specific emissions. The variability of the impact potentials as a function of incinerator characteristics therefore calls for the use of site-specific data when required by the LCA goal and scope definition phase, in particular when the study focuses on a specific incinerator or on a local waste management plan, and when these data are available

Utilization of stabilized municipal waste combustion ash residues as construction material

International Nuclear Information System (INIS)

Shieh, C.S.

1992-01-01

Stabilized municipal waste combustion (MWC) ash residues were investigated for their potential as construction material that can be beneficially used in terrestrial and marine environments. End-use products, such as patio stones, brick pavers, solid blocks, and reef units, were fabricated and tested for their engineering and chemical characteristics. engineering feasibility and environmental acceptability of using stabilized ash residues as construction material are discussed in this paper. Ash samples were collected from two mass-burn facilities and one refuse derived fuel (RDF) facility in Florida

Advanced immobilization processes for fuel hulls and dissolver residues

International Nuclear Information System (INIS)

Hebel, W.; Boehme, G.; Findlay, J.R.; Sombret, C.

1984-08-01

Various research and development projects for the conditioning of cladding scraps and dissolver residues are pursued within the scope of the R and D programme on nuclear waste Management of the European Community. They include the characterization of the waste materials arising from industrial fuel reprocessing and the development of different waste immobilization techniques. These concern the embedment of scraps and residues into inert matrices like cement, metal alloys, compacted graphite and sintered ceramics as well as the treatment of the fuel hulls by melting or chemical conversion. The conditioned waste forms are tested as to their relevant properties for activity enclosure

Advanced immobilization processes for fuel hulls and dissolver residues

International Nuclear Information System (INIS)

Hebel, W.; Boehme, G.; Findlay, J.R.; Sombert, C.

1984-01-01

Various research and development projects for the conditioning of cladding scraps and dissolver residues are pursued within the scope of the R and D programme on nuclear waste Management of the European Community. They include the characterization of the waste materials arising from industrial fuel reprocessing and the development of different waste immobilization techniques. These concern the embedment of the scraps and residues into inert matrices like cement, metal alloys, compacted graphite and sintered ceramics as well as the treatment of the fuel hulls by melting or chemical conversion. The conditioned waste forms are tested as to their relevant properties for activity enclosure

Thermally induced transformations of iron oxide stabilised APC residues from waste incineration

DEFF Research Database (Denmark)

Sørensen, Mette Abildgaard; Koch, C.B.

2001-01-01

Air pollution control (APC) facilities at waste incinerator plants produce large quantities of solid residues rich in salts and heavy metals. Heavy metals are readily released to water from the residues and it has, therefore, been found suitable to apply a rapid co-precipitation/adsorption process...... as a means to immobilize the toxic elements. In the 'Ferrox process', this immobilization is based on co-precipitation with an Fe(III) oxide formed by oxidation of Fe(II) by air in an aqueous slurry with the APC residue at alkaline pH. In this work we have undertaken a Mossbauer spectroscopy study of the Fe...

Does a plant for mechanical-biological waste treatment require a sanitary landfill?; Braucht die MBA eine Deponie?

Energy Technology Data Exchange (ETDEWEB)

Schulte, Burkart [GVoA mbH und Co. KG, Hille (Germany)

2012-11-01

In mechanical-biological waste treatment, an interesting recyclable fraction is dumped in landfill together with other treatment residues. This may be 10-20% depending on the energy content of the initial material. Some operators of mechanical-biological waste treatment plants are currently working on modifying their waste treatment processes. Results so far have shown that this may also reduce the cost. (orig.) [German] Bei der bisherigen Abfallentsorgung mittels einer MBA (mechanisch-biologische Abfallbehandlung) wird immer noch ein interessanter Wertstoffanteil mit dem Deponat auf der Deponie abgelagert. Je nach Qualitaet der Vorbehandlung sind dies alleine vom Energieinhalt des Eingangsmaterials ca. 10-20%. Um auch diesen Anteil zu verwerten, sind aktuell einige MBA-Betreiber dabei, ihre Verfahren entsprechend umzustellen. Erste Ergebnisse zeigen, dass dies auch noch zu Kosteneinsparungen fuehren kann. (orig.)

The Hybrid Treatment Process for mixed radioactive and hazardous waste treatment

International Nuclear Information System (INIS)

Ross, W.A.; Kindle, C.H.

1992-06-01

This paper describes a new process for treating mixed hazardous and radioactive waste, commonly called mixed waste. The process is called the Hybrid Treatment Process (HTP), so named because it is built on the 20 years of experience with vitrification of wastes in melters, and the 12 years of experience with treatment of wastes by the in situ vitrification (ISV) process. It also uses techniques from several additional technologies. Mixed wastes are being generated by both the US Department of Energy (DOE) and by commercial sources. The wastes are those that contain both a hazardous waste regulated under the US Environmental Protection Agency's (EPA) Resource, Conservation, and Recovery Act (RCRA) regulations and a radioactive waste with source, special nuclear, or byproduct materials. The dual regulation of the wastes increases the complexity of the treatment, handling, and storage of the waste. The DOE is the largest holder and generator of mixed waste. Its mixed wastes are classified as either high-level, transuranic (TRU), or low-level waste (LLW). High-level mixed wastes will be treated in vitrification plants. Transuranic wastes may be disposed of without treatment by obtaining a no-migration variance from the EPA. Lowlevel wastes, however, will require treatment, but treatment systems with sufficient capacity are not yet available to DOE. Various facilities are being proposed for the treatment of low-level waste. The concept described in this paper represents one option for establishing that treatment capacity

Development of ecologically safety technology for steam-thermal treatment of organic wastes

Energy Technology Data Exchange (ETDEWEB)

Juravskij, J [Centre for Science, Technology and Industrial Applications, ` ` Tokema` ` , Minsk (Belarus)

1997-02-01

The experience on mitigation of the consequences of the Chernobyl`s nuclear power station accident proves that the treatment of large amounts of organic and mixed wastes containing radionuclides is a very urgent scientific and technical problem. In this connection a search for new ideas and development of highly efficient and ecologically safety technologies for treatment of organic radioactive wastes has been undertaken. This study is based on use of physico-mechanical properties of various organic materials (wood, rubber-containing composites, plastics, biomass) subjected to thermal decomposition in the overheated water steam medium. Under such conditions, there is a possibility, under relatively low temperatures (400 - 500 deg. C), to realize thermal decomposition and considerably (in 8 - 50 times) to reduce the amount of wastes, to obtain the main concentration of radionuclides in the solid residue and to prevent releases of gaseous products containing radionuclides to the environment. (author). 5 figs, 1 tab.

Design of A District Heating System Including The Upgrading of Residual Industrial Waste Heat

NARCIS (Netherlands)

Falcao, P.W.; Mesbah, A.; Suherman, M.V.; Wennekes, S.

2005-01-01

This study was aimed to evaluate the feasibility of using a waste heat stream from DSM for a District Heating System. A conceptual design was carried out with emphasis on the unit for upgrading the residual waste heat. Having reviewed heat pump technology, mechanical heat pump was found to be the

Solid waste electron beam treatment

International Nuclear Information System (INIS)

Chmielewski, A.G.

1998-01-01

The possible applications of electron accelerators for solid waste treatment are discussed in the report. The elaborated technologies allow to recycle of materials (e.g. cellulosic materials in municipal waste), improve their hygienic standards (agricultural usage of sludge from municipal waste water treatment) and reduce harmful to environment chemical usage (cellulose degradation). These are environment friendly advanced technologies which meets demands waste recycling. (author)

Solid waste electron beam treatment

Energy Technology Data Exchange (ETDEWEB)

Chmielewski, A G

1998-07-01

The possible applications of electron accelerators for solid waste treatment are discussed in the report. The elaborated technologies allow to recycle of materials (e.g., cellulosic materials in municipal waste), improve their hygienic standards (agricultural usage of sludge from municipal waste water treatment) and reduce harmful to environment chemical usage (cellulose degradation). These are environment friendly advanced technologies which meets demands waste recycling. (author)

Case study: Is the 'catch-all-plastics bin' useful in unlocking the hidden resource potential in the residual waste collection system?

Science.gov (United States)

Kranzinger, Lukas; Schopf, Kerstin; Pomberger, Roland; Punesch, Elisabeth

2017-02-01

Austria's performance in the collection of separated waste is adequate. However, the residual waste still contains substantial amounts of recyclable materials - for example, plastics, paper and board, glass and composite packaging. Plastics (lightweight packaging and similar non-packaging materials) are detected at an average mass content of 13% in residual waste. Despite this huge potential, only 3% of the total amount of residual waste (1,687,000 t y -1 ) is recycled. This implies that most of the recyclable materials contained in the residual waste are destined for thermal recovery and are lost for recycling. This pilot project, commissioned by the Land of Lower Austria, applied a holistic approach, unique in Europe, to the Lower Austrian waste management system. It aims to transfer excess quantities of plastic packaging and non-packaging recyclables from the residual waste system to the separately collected waste system by introducing a so-called 'catch-all-plastics bin'. A quantity flow model was constructed and the results showed a realistic increase in the amount of plastics collected of 33.9 wt%. This equals a calculated excess quantity of 19,638 t y -1 . The increased plastics collection resulted in a positive impact on the climate footprint (CO 2 equivalent) in line with the targets of EU Directive 94/62/EG (Circular Economy Package) and its Amendments. The new collection system involves only moderate additional costs.

Thermal treatment for TRU waste sorting

International Nuclear Information System (INIS)

Sasaki, Toshiki; Aoyama, Yoshio; Yamashita, Toshiyuki

2009-03-01

A thermal treatment that can automatically unpack TRU waste and remove hazardous materials has been developed to reduce the risk of radiation exposure and save operation cost. The thermal treatment is a process of removing plastic wrapping and hazardous material from TRU waste by heating waste at 500 to 700degC. Plastic wrappings of simulated wastes were removed using a laboratory scale thermal treatment system. Celluloses and isoprene rubbers that must be removed from waste for disposal were pyrolyzed by the treatment. Although the thermal treatment can separate lead and aluminum from the waste, a further technical development is needed to separate lead and aluminum. A demonstration scale thermal treatment system that comprises a rotary kiln with a jacket water cooler and a rotating inner cage for lead and aluminum separation is discussed. A clogging prevention system against zinc chloride, a lead and aluminum accumulation system, and a detection system for spray cans that possibly cause explosion and fire are also discussed. Future technology development subjects for the TRU waste thermal treatment system are summarized. (author)

Treatment of wastes from biomass used in electricity production

International Nuclear Information System (INIS)

Guillemes Peira, Ángel

2015-01-01

The main objective of this study is to find an approach for the treatment of toxic waste condensates obtained during the generation of electricity from biomass that would transform them into wastewater. Two experimental conditions have been performed using a reactor. During the first condition, potentials were applied without following a defined path to electrically calibrate the system by observing responses. In the second experimental condition and based on these previous electrical observations, the potentials were applied. This technical approach has proven suitable for condensate treatment. However, given the aggressiveness of the residue, it is necessary to use a reactor which allows reaching and maintaining the necessary electro-oxidation potential and to combine it with an electrocoagulation reactor. (author)

Properties of residual marine fuel produced by thermolysis from polypropylene waste

Directory of Open Access Journals (Sweden)

Linas Miknius

2015-06-01

Full Text Available Thermal degradation of waste plastics with the aim of producing liquid fuel is one of the alternative solutions to landfill disposal or incineration. The paper describes thermal conversion of polypropylene waste and analysis of produced liquid fuel that would satisfy ISO 8217-2012 requirements for a residual marine fuel. Single pass batch thermolysis processes were conducted at different own vapour pressures (20-80 barg that determined process temperature, residence time of intermediates what resulted in different yields of the liquid product. Obtained products were stabilized by rectification to achieve required standard flash point. Gas chromatography and 1H NMR spectrometry show aliphatic nature of the liquid product where majority of the compounds are isoalkanes and isoalkenes. Only lightest fractions boiling up to a temperature of 72 oC have significant amount of n-pentane. Distribution of aromatic hydrocarbons is not even along the boiling range. The fractions boiling at a temperature of 128 oC and 160 oC have the highest content of monocyclic arenes – 3.16 % and 4.09 % respectively. The obtained final liquid residual product meets all but one requirements of ISO 8217-2012 for residual marine fuels.DOI: http://dx.doi.org/10.5755/j01.ms.21.2.6105

Tank waste treatment science

International Nuclear Information System (INIS)

LaFemina, J.P.; Blanchard, D.L.; Bunker, B.C.; Colton, N.G.; Felmy, A.R.; Franz, J.A.; Liu, J.; Virden, J.W.

1994-01-01

Remediation efforts at the U.S. Department of Energy's Hanford Site require that many technical and scientific principles be combined for effectively managing and disposing the variety of wastes currently stored in underground tanks. Based on these principles, pretreatment technologies are being studied and developed to separate waste components and enable the most suitable treatment methods to be selected for final disposal of these wastes. The Tank Waste Treatment Science Task at Pacific Northwest Laboratory is addressing pretreatment technology development by investigating several aspects related to understanding and processing the tank contents. The experimental work includes evaluating the chemical and physical properties of the alkaline wastes, modeling sludge dissolution, and evaluating and designing ion exchange materials. This paper gives some examples of results of this work and shows how these results fit into the overall Hanford waste remediation activities. This work is part of series of projects being conducted for the Tank Waste Remediation System

Hanford Tank Waste - Near Source Treatment of Low Activity Waste

International Nuclear Information System (INIS)

Ramsey, William Gene

2013-01-01

Abstract only. Treatment and disposition of Hanford Site waste as currently planned consists of 100+ waste retrievals, waste delivery through up to 8+ miles of dedicated, in-ground piping, centralized mixing and blending operations- all leading to pre-treatment combination and separation processes followed by vitrification at the Hanford Tank Waste Treatment and Immobilization Plant (WTP). The sequential nature of Tank Farm and WTP operations requires nominally 15-20 years of continuous operations before all waste can be retrieved from many Single Shell Tanks (SSTs). Also, the infrastructure necessary to mobilize and deliver the waste requires significant investment beyond that required for the WTP. Treating waste as closely as possible to individual tanks or groups- as allowed by the waste characteristics- is being investigated to determine the potential to 1) defer, reduce, and/or eliminate infrastructure requirements, and 2) significantly mitigate project risk by reducing the potential and impact of single point failures. The inventory of Hanford waste slated for processing and disposition as LAW is currently managed as high-level waste (HLW), i.e., the separation of fission products and other radionuclides has not commenced. A significant inventory of this waste (over 20M gallons) is in the form of precipitated saltcake maintained in single shell tanks, many of which are identified as potential leaking tanks. Retrieval and transport (as a liquid) must be staged within the waste feed delivery capability established by site infrastructure and WTP. Near Source treatment, if employed, would provide for the separation and stabilization processing necessary for waste located in remote farms (wherein most of the leaking tanks reside) significantly earlier than currently projected. Near Source treatment is intended to address the currently accepted site risk and also provides means to mitigate future issues likely to be faced over the coming decades. This paper

Heavy metal vaporization and abatement during thermal treatment of modified wastes

International Nuclear Information System (INIS)

Rio, S.; Verwilghen, C.; Ramaroson, J.; Nzihou, A.; Sharrock, P.

2007-01-01

This study examines the vaporization percentage and partitioning of heavy metals Cd, Pb and Zn during thermal treatment of wastes with added PVC, heavy metals or phosphate, and the efficiency of sorbents for removal of these metallic compounds in flue gas of an industrial solid waste incinerator. Firstly, vaporization experiments were carried out to determine the behavior of heavy metals during combustion under various conditions (type of waste, temperature, presence of chloride or phosphate ...). The experimental results show relatively high vaporization percentage of metallic compounds within fly ash and limestone matrix while heavy metals within sediments treated with phosphoric acid are less volatile. Vaporization of metals increases with increasing temperature and with chloride addition. The thermal behavior of the selected heavy metals and their removal by sorbents (sodium bicarbonate, activated carbon) was also studied in an industrial solid waste incinerator. These pilot scale experiments confirm that heavy metals are concentrated in fly ashes and cyclone residues, thus effectively controlling their release to the atmosphere

Allowable residual contamination levels: transuranic advanced disposal systems for defense waste

International Nuclear Information System (INIS)

Kennedy, W.E. Jr.; Napier, B.A.

1982-01-01

An evaluation of advanced disposal systems for defense transuranic (TRU) wastes is being conducted using the Allowable Residual Contamination Level (ARCL) method. The ARCL method is based on compliance with a radiation dose rate limit through a site-specific analysis of the potential for radiation exposure to individuals. For defense TRU wastes at the Hanford Site near Richland, Washington, various advanced disposal techniques are being studied to determine their potential for application. This paper presents a discussion of the results of the first stage of the TRU advanced disposal systems project

Treatment of the oily waste sludges through thermal plasma in absence of oxygen

International Nuclear Information System (INIS)

Castaneda J, G.; Pacheco S, J.

2001-01-01

The thermal plasma process in absence of oxygen for the degradation of oily waste sludges was evaluated. These residues are commonly generated in the petrochemical industry and are considered hazardous wastes according to the present environmental regulations. The process was operated using difference residence times and the characteristics of the gaseous by products and residual soils were determined. The efficiency of organic matter degradation was 99.99%. The attained volume reduction, under the best conditions was 95.5%. The residual soils were composed of carbon and clays. The residual gases have low molecular weight. The resulting final wastes were non-hazardous and could be disposed of in landfills. (Author)

Recycling systems and material flows from the viewpoint of thermal waste treatment; Kreislaufwirtschaft- und Stoffstrombetrachtungen aus Sicht der thermischen Abfallbehandlung

Energy Technology Data Exchange (ETDEWEB)

Johnke, B. [Umweltbundesamt, Berlin (Germany); Mast, P.G. [Tauw Umwelt GmbH, Berlin (Germany)

1998-09-01

Material stream analysis can serve as a basis for decisions on which materials should be kept in circulation, and in what quantity, and which materials it is better to remove from the recycling system and dispose of as waste. Wastes destined for disposal are mostly transferred to waste treatment plants and landfills. The role of thermal treatment as part of the disposal system is to destroy or decompose organic pollutants contained in the waste, concentrate and remove inorganic pollutants, make the heat arising during the treatment process available for use as energy, and make the greatest possible physical use of the treatment residues. The present paper reviews the current regulations for the promotion of recycling and investigates selected material streams and the fate of these materials. In connection with the residue quality of household waste incineration slag as a thermal waste treatment product it also considers the influence of waste management measures on wastes destined for disposal. [Deutsch] Stoffstrombetrachtungen koennen als Grundlage fuer Entscheidungen dienen, welche Stoffe in welchem Umfang im Kreislauf verbleiben oder wieder integriert werden sollten und welche besser als Abfall zur Beseitigung aus dem Kreislaufsystem auszuschleusen sind. Fuer Abfaelle zur Beseitigung wird diese Aufgabe i.d.R. von thermischen Abfallbehandlungsanlagen und Deponien uebernommen. Im Rahmen der Entsorgung kommt der thermischen Behandlung dabei die Aufgabe zu, die im Abfall zur Beseitigung enthaltenen organischen Schadstoffe zu zerstoeren oder abzubauen, anorganische Schadstoffe aufzukonzentrieren und auszuschleusen, die bei dem Behandlungsprozess entstehende Waerme einer weitgehenden Energienutzung zuzufuehren und die Rueckstaende aus der Behandlung so weit wie moeglich stofflich zu verwerten. Nachfolgend sollen insbesondere die Regelungen zur Unterstuetzung der Kreislaufwirtschaft, ausgewaehlte Stofffluesse und der Verbleib dieser Stoffe und Materialien und der

Legal problems of waste treatment in German atomic energy facilities

International Nuclear Information System (INIS)

Pfaffelhuber, J.K.

1980-01-01

The execution of the strategies of waste treatment and disposal calls for the laws and regulations on the obligations of the owners of equipments and facilities and of the state for securing safety and the final elimination of radioactive wastes, which are defined mainly in Article 9 of Atomgesetz and Section 2 (Article 44 - 48) of the order on protection from radiation. The owners of equipments and facilities of atomic energy technology shall limit the emission of radiation to about 6% of internationally permissible values, avoid uncontrolled emission without fail, inspect emission and submit reports yearly to government offices. The owners have attention obligations to utilize harmlessly produced radioactive residues and the expanded or dismantled parts of radioactive equipments or to eliminate orderly such things as radioactive wastes, only when such utilization is unable technically or economically, or not adequate under the protection aims of Atomgesetz. The possessors of radioactive wastes shall deliver the wastes to the accumulation places of provinces for intermediate storage, to the facilities of the Federal Republic for securing safety or final storage, or the facilities authorized by government offices for the elimination of radioactive wastes. Provinces shall install the accumulation places for the intermediate storage of radioactive wastes produced in their territories, and the Federal Republic shall set up the facilities for securing safety and the final elimination of radioactive wastes (Article 9, Atomgesetz). (Okada, K.)

Treatment of biological waste and residues V. Biological - mechanical - thermal processes; Bio- und Restabfallbehandlung V. Biologisch - mechanisch - thermisch

Energy Technology Data Exchange (ETDEWEB)

Wiemer, K.; Kern, M. (eds.); Weber-Wied, R. (comp.)

2001-07-01

From 2005, the TA Siedlungsabfall (Waste Management Regulation) will come into force, and European legislation will overrule national legislation. Dumping of untreated waste in landfills will be prohibited, i.e. incinerators for thermal waste treatment must be constructed. In view of the rigid specifications for emissions and residues and the demand for Europe-wide invitations for tender, time is running short. The book outlines the options for action of the German states and of some applicant states for EC membership. The German government already issued an Ordinance for Power Generation from Biomass. Independent of this, also secondary fuels are gaining ground, and several contributions of the conference discussed quality assurance and utilization of secondary fuels. Composting and sewage sludge utilization are further current issues. Air pollution, soil and groundwater protection, job security and energy potential are gone into, and an outline of the current situation of waste management is attempted. [German] Die aktuelle abfallwirtschaftliche Situation wird in besonderem Masse gepraegt durch das nahende Jahr 2005 sowie die zunehmende Abhaengigkeit nationalstaatlicher Handlungsspielraeume von den Vorgaben europaeischer Rahmenrichtlinien. Hierbei wird der Handlungsdruck spuerbar, spaetestens ab dem Jahr 2005 der TA Siedlungsabfall Rechnung tragen zu muessen. Die verbleibenden Zeitraeume sind daher eng bemessen, beruecksichtigt man insbesondere die langen Genehmigungs- und Errichtungszeitraeume fuer thermische Behandlungsanlagen. Vor dem Hintergrund der europaweiten Ausschreibungspflicht wird die gegenwaertige technische Diskussion zur MBA sehr stark durch die nunmehr von der Bundesregierung konkretisierten Emissions- und Ablagerungsanforderungen gepraegt. Der vorliegende Band soll aufzeigen, welche Handlungsspielraeume sich hierbei aus Sicht der verschiedenen Bundeslaender ergeben. Ein Blick ueber die Grenzen hinaus zu einigen zukuenftigen EU

Mixed waste treatment model: Basis and analysis

International Nuclear Information System (INIS)

Palmer, B.A.

1995-09-01

The Department of Energy's Programmatic Environmental Impact Statement (PEIS) required treatment system capacities for risk and cost calculation. Los Alamos was tasked with providing these capacities to the PEIS team. This involved understanding the Department of Energy (DOE) Complex waste, making the necessary changes to correct for problems, categorizing the waste for treatment, and determining the treatment system requirements. The treatment system requirements depended on the incoming waste, which varied for each PEIS case. The treatment system requirements also depended on the type of treatment that was desired. Because different groups contributing to the PEIS needed specific types of results, we provided the treatment system requirements in a variety of forms. In total, some 40 data files were created for the TRU cases, and for the MLLW case, there were 105 separate data files. Each data file represents one treatment case consisting of the selected waste from various sites, a selected treatment system, and the reporting requirements for such a case. The treatment system requirements in their most basic form are the treatment process rates for unit operations in the desired treatment system, based on a 10-year working life and 20-year accumulation of the waste. These results were reported in cubic meters and for the MLLW case, in kilograms as well. The treatment system model consisted of unit operations that are linked together. Each unit operation's function depended on the input waste streams, waste matrix, and contaminants. Each unit operation outputs one or more waste streams whose matrix, contaminants, and volume/mass may have changed as a result of the treatment. These output streams are then routed to the appropriate unit operation for additional treatment until the output waste stream meets the treatment requirements for disposal. The total waste for each unit operation was calculated as well as the waste for each matrix treated by the unit

A process for treatment of mixed waste containing chemical plating wastes

International Nuclear Information System (INIS)

Anast, K.R.; Dziewinski, J.; Lussiez, G.

1995-01-01

The Waste Treatment and Minimization Group at Los Alamos National Laboratory has designed and will be constructing a transportable treatment system to treat low-level radioactive mixed waste generated during plating operations. The chemical and plating waste treatment system is composed of two modules with six submodules, which can be trucked to user sites to treat a wide variety of aqueous waste solutions. The process is designed to remove the hazardous components from the waste stream, generating chemically benign, disposable liquids and solids with low level radioactivity. The chemical and plating waste treatment system is designed as a multifunctional process capable of treating several different types of wastes. At this time, the unit has been the designated treatment process for these wastes: Destruction of free cyanide and metal-cyanide complexes from spent plating solutions; destruction of ammonia in solution from spent plating solutions; reduction of Cr VI to Cr III from spent plating solutions, precipitation, solids separation, and immobilization; heavy metal precipitation from spent plating solutions, solids separation, and immobilization, and acid or base neutralization from unspecified solutions

Environmental impact by toxic compounds from waste treatment; Miljoepaaverkan fraan toxiska aemnen vid hantering av avfall

Energy Technology Data Exchange (ETDEWEB)

Loefblad, Gun; Bisaillon, Mattias; Sundberg, Johan (Profu AB (Sweden))

2010-07-01

The study deals with emissions of toxic compounds from waste treatment to the environment with the aim of improving the state of knowledge and to find a way of describing the environmental impact from these substances. Toxicity is one of a number of environmental aspects necessary to address in the planning of waste treatment and in the daily waste treatment routines in order to fulfill the environmental objective A Non-Toxic Environment and other environmental requirements. The study includes waste to incineration, composting and anaerobic digestion. A comparison between methods were made for biological household waste. According to our study, the compounds of importance for waste treatment are metals and persistent organic compounds. These tend to bioaccumulate and enrich in food chains. The substances are important for the environmental objective A Non-Toxic Environment. In a first step the compounds chosen in this study may be suggested for describing toxicity from waste treatment: As, Cd, Cu, Hg, Pb, dioxin, PCB, the phthalate DEHP and the brominated flame retardant HBCDD. Other substances may be added to the list in a next step from up-dated and quality-assured characterisation factors or from other requirements or preferences. There is a limited knowledge on toxic compounds in waste flows and in different environmental compartments. More data are available for metals than for organic substances. There is also a limited knowledge on the fate of the compounds during the waste treatment processes. Most information is found for incineration. During composting and anaerobic digestion the metals will mainly be emitted to the environment by use of the compost and the anaerobic digestion residue. Organic substances will to some extent be degraded during the processes. However, there are gaps of knowledge to fill for the further work on estimating toxic emissions. There is mainly a need for more extensive data on toxic compounds in waste and their variations. A test

Residual water treatment for gamma radiation

International Nuclear Information System (INIS)

Mendez, L.

1990-01-01

The treatment of residual water by means of gamma radiation for its use in agricultural irrigation is evaluated. Measurements of physical, chemical, biological and microbiological contamination indicators were performed. For that, samples from the treatment center of residual water of San Juan de Miraflores were irradiated up to a 52.5 kGy dose. The study concludes that gamma radiation is effective to remove parasites and bacteria, but not for removal of the organic and inorganic matter. (author). 15 refs., 3 tabs., 4 figs

Waste management system alternatives for treatment of wastes from spent fuel reprocessing

International Nuclear Information System (INIS)

McKee, R.W.; Swanson, J.L.; Daling, P.M.

1986-09-01

This study was performed to help identify a preferred TRU waste treatment alternative for reprocessing wastes with respect to waste form performance in a geologic repository, near-term waste management system risks, and minimum waste management system costs. The results were intended for use in developing TRU waste acceptance requirements that may be needed to meet regulatory requirements for disposal of TRU wastes in a geologic repository. The waste management system components included in this analysis are waste treatment and packaging, transportation, and disposal. The major features of the TRU waste treatment alternatives examined here include: (1) packaging (as-produced) without treatment (PWOT); (2) compaction of hulls and other compactable wastes; (3) incineration of combustibles with cementation of the ash plus compaction of hulls and filters; (4) melting of hulls and failed equipment plus incineration of combustibles with vitrification of the ash along with the HLW; (5a) decontamination of hulls and failed equipment to produce LLW plus incineration and incorporation of ash and other inert wastes into HLW glass; and (5b) variation of this fifth treatment alternative in which the incineration ash is incorporated into a separate TRU waste glass. The six alternative processing system concepts provide progressively increasing levels of TRU waste consolidation and TRU waste form integrity. Vitrification of HLW and intermediate-level liquid wastes (ILLW) was assumed in all cases

A Primer on Waste Water Treatment.

Science.gov (United States)

Department of the Interior, Washington, DC. Federal Water Pollution Control Administration.

This information pamphlet is for teachers, students, or the general public concerned with the types of waste water treatment systems, the need for further treatment, and advanced methods of treating wastes. Present day pollution control methods utilizing primary and secondary waste treatment plants, lagoons, and septic tanks are described,…

Hazardous waste treatment facility and skid-mounted treatment systems at Los Alamos

International Nuclear Information System (INIS)

Lussiez, G.W.; Zygmunt, S.J.

1993-01-01

To centralize treatment, storage, and staging areas for hazardous wastes, Los Alamos National Laboratory has designed a 12,000-ft 2 hazardous waste treatment facility. The facility will house a treatment room for each of four kinds of wastes: nonradioactive characteristic wastes, nonradioactive listed wastes radioactive characteristic wastes, and radioactive listed wastes. The facility will be used for repacking labpacks, bulking small organic waste volumes, processing scintillation vials, treating reactives such as lithium hydride and pyrophoric uranium, treating contaminated solids such as barium sand, and treating plating wastes. The treated wastes will then be appropriately disposed of. This report describes the integral features of the hazardous waste treatment facility

Bioenergy from sisal residues

Energy Technology Data Exchange (ETDEWEB)

Jungersen, G. [Dansk Teknologisk Inst. (Denmark); Kivaisi, A.; Rubindamayugi, M. [Univ. of Dar es Salaam (Tanzania, United Republic of)

1998-05-01

The main objectives of this report are: To analyse the bioenergy potential of the Tanzanian agro-industries, with special emphasis on the Sisal industry, the largest producer of agro-industrial residues in Tanzania; and to upgrade the human capacity and research potential of the Applied Microbiology Unit at the University of Dar es Salaam, in order to ensure a scientific and technological support for future operation and implementation of biogas facilities and anaerobic water treatment systems. The experimental work on sisal residues contains the following issues: Optimal reactor set-up and performance; Pre-treatment methods for treatment of fibre fraction in order to increase the methane yield; Evaluation of the requirement for nutrient addition; Evaluation of the potential for bioethanol production from sisal bulbs. The processing of sisal leaves into dry fibres (decortication) has traditionally been done by the wet processing method, which consumes considerable quantities of water and produces large quantities of waste water. The Tanzania Sisal Authority (TSA) is now developing a dry decortication method, which consumes less water and produces a waste product with 12-15% TS, which is feasible for treatment in CSTR systems (Continously Stirred Tank Reactors). (EG)

Sustainable treatment of municipal waste water

DEFF Research Database (Denmark)

Hansen, Peter Augusto; Larsen, Henrik Fred

The main goal of the EU FP6 NEPTUNE program is to develop new and improve existing waste water treatment technologies (WWTT) and sludge handling technologies for municipal waste water, in accordance with the concepts behind the EU Water Framework Directive. As part of this work, the project.......e. heavy metals, pharmaceuticals and endocrine disruptors) in the waste water. As a novel approach, the potential ecotoxicity and human toxicity impacts from a high number of micropollutants and the potential impacts from pathogens will be included. In total, more that 20 different waste water and sludge...... treatment technologies are to be assessed. This paper will present the first LCA results from running existing life cycle impact assessment (LCIA) methodology on some of the waste water treatment technologies. Keywords: Sustainability, LCA, micropollutants, waste water treatment technologies....

Chemical aspects of nuclear waste treatment

International Nuclear Information System (INIS)

Bond, W.D.

1980-01-01

The chemical aspects of the treatment of gaseous, liquid, and solid wastes are discussed in overview. The role of chemistry and the chemical reactions in waste treatment are emphasized. Waste treatment methods encompass the chemistry of radioactive elements from every group of the periodic table. In most streams, the radioactive elements are present in relatively low concentrations and are often associated with moderately large amounts of process reagents, or materials. In general, it is desirable that waste treatment methods are based on chemistry that is selective for the concentration of radionuclides and does not require the addition of reagents that contribute significantly to the volume of the treated waste. Solvent extraction, ion exchange, and sorbent chemistry play a major role in waste treatment because of the high selectivity provided for many radionuclides. This paper deals with the chemistry of the onsite treatment methods that is typically used at nuclear installations and is not concerned with the chemistry of the various alternative materials proposed for long-term storage of nuclear wastes. The chemical aspects are discussed from a generic point of view in which the chemistry of important radionuclides is emphasized

Long-term management of the existing radioactive wastes and residues at the Niagara Falls Storage Site. Draft Environmental Impact Statement

International Nuclear Information System (INIS)

1984-08-01

The statement assesses and compares several alternatives for long-term management of the existing radioactive wastes and residues at the Niagara Falls Storage Site (NFSS), Lewiston, New York. The alternatives include: (1) no action (continued interim storage at NFSS within a diked and capped containment area), (2) long-term management at NFSS (improved containment, with or without modified form of the residues), (3) long-term management at other DOE sites (Hanford, Washington, or Oak Ridge, Tennessee), and (4) offsite management of the residues at Hanford or Oak Ridge and either leaving the wastes at NFSS or removing them for disposal in the ocean. In addition to alternatives analyzed in depth, several options are also considered, including: other modifications of residue form, modification of the basic conceptual designs, other containment design options, transportation routes, and transportation modes. The radiological health effects (primarily increased risk of cancer) associated with long-term management of the wastes and residues are expected to be smaller than the nonradiological risks of occupational and transportation-related injuries and deaths. During the action period, the risk is highest for workers if all wastes and residues are moved to Hanford. The risk is highest for the general public if the residues are moved to Hanford and the wastes are moved to the ocean. Dispersal of the slightly contaminated wastes in the ocean is not expected to result in any significant impacts on the ocean environment or pose any significant radiological risk to humans. For all alternatives, if controls ceased, there would be eventual dispersion of the radioactive materials to the environment. If it is assumed that all controls cease, predicted time for loss of covers over the buried materials ranges from several hundred years to more than two million years, depending on the use of the land surface

Stabilization of APC residues from waste incineration with ferrous sulfate on a semi-industrial scale

DEFF Research Database (Denmark)

Lundtorp, Kasper; Jensen, Dorthe Lærke; Christensen, Thomas Højlund

2002-01-01

A stabilization method for air pollution control (APC) residues from municipal solid waste incineration (MSWI) involving mixing of the residue with water and FeSO4 has been demonstrated on a semi-industrial scale on three types of APC residues: a semidy (SD) APC residue, a fly ash (FA), and an FA...... mixed with sludge (FAS) from a wet flue gas cleaning system. The process was performed in batches of 165-175 kg residue. It generates a wastewater that is highly saline but has a low content of heavy metals such as Cd, Cr, and Pb. The stabilized and raw residues have been subject to a range of leaching...

Building flexibility into the design of a pilot plant for the immobilisation of Pu containing residues and wastes

Energy Technology Data Exchange (ETDEWEB)

Scales, C R; Maddrell, E R [NNL, Havelock Rd, Workington, CA14 3YQ (United Kingdom); Hobbs, J; Stephen, R [Sellafield Ltd, Sellafield, CA20 1 PG (United Kingdom); Moricca, S; Stewart, M W A [ANSTO, New Illawara Road, Lucas Heights 2234 (Australia)

2013-07-01

NNL and ANSTO on behalf of Sellafield Ltd have developed a process for the immobilisation of a range of Pu containing wastes and residues. Following the inactive demonstration of the technology the project is now focusing on the design of an active pilot plant capable of validating the technology and ultimately immobilising a waste inventory containing around 100 kg plutonium. The diverse wastes from which it is uneconomic to recover Pu, require a flexible process with a wide product envelope capable of producing a wasteform suitable for disposal in a UK repository. Ceramics, glass ceramics and metal encapsulated waste-forms can be delivered by the process line which incorporates size reduction and heat treatment techniques with the aim of feeding a hot isostatic pressing process designed to deliver the highly durable waste-forms. Following a demonstration of feasibility, flowsheet development is progressing to support the design which has the aim of a fully flexible facility based in NNL's Central Laboratory on the Sellafield site. Optimisation of the size reduction, mixing and blending operations is being carried out using UO{sub 2} as a surrogate for PuO{sub 2}. This work is supporting the potential of using an enhanced glass ceramic formulation in place of the full ceramic with the aim of simplifying glove box operations. Heat treatment and subsequent HIPing strategies are being explored in order to eliminate any carbon from the feeds without increasing the valence state of the uranium present in some of the inventory which can result in an unwanted increase in wasteform volumes. The HIP and ancillary systems are being specifically designed to meet the requirements of the Sellafield site and within the constraints of the NNL Central Laboratory. The HIP is being configured to produce consolidated product cans consistent with the requirements of ongoing storage and disposal. With the aim of one cycle per day, the facility will deliver its mission of

Life cycle assessment of integrated solid state anaerobic digestion and composting for on-farm organic residues treatment.

Science.gov (United States)

Li, Yangyang; Manandhar, Ashish; Li, Guoxue; Shah, Ajay

2018-03-20

Driven by the gradual changes in the structure of energy consumption and improvements of living standards in China, the volume of on-farm organic solid waste is increasing. If untreated, these unutilized on-farm organic solid wastes can cause environmental problems. This paper presents the results of a life cycle assessment to compare the environmental impacts of different on-farm organic waste (which includes dairy manure, corn stover and tomato residue) treatment strategies, including anaerobic digestion (AD), composting, and AD followed by composting. The input life cycle inventory data are specific to China. The potential environmental impacts of different waste management strategies were assessed based on their acidification potential (AP), eutrophication potential (EP), global warming potential (GWP), ecotoxicity potential (ETP), and resource depletion (RD). The results show that the preferred treatment strategy for dairy manure is the one that integrated corn stover and tomato residue utilization and solid state AD technologies into the system. The GWP of integrated solid state AD and composting was the least, which is -2900 kg CO 2 eq/ t of dairy manure and approximately 14.8 times less than that of current status (i.e., liquid AD of dairy manure). Solid state AD of dairy manure, corn stover and tomato residues is the most favorable option in terms of AP, EP and ETP, which are more than 40% lower than that of the current status (i.e., AP: 3.11 kg SO 2 , EP: -0.94 kg N, and ETP: -881 CTUe (Comparative Toxic Units ecotoxicity)). The results also show that there is a significant potential for AP, EP, ETP, and GWP reduction, if AD is used prior to composting. The scenario analysis for transportation distance showed that locating the AD plant and composting facility on the farm was advantageous in terms of all the life cycle impact categories. Copyright © 2018 Elsevier Ltd. All rights reserved.

Behaviour of antimony during thermal treatment of Sb-rich halogenated waste

International Nuclear Information System (INIS)

Klein, J.; Dorge, S.; Trouve, G.; Venditti, D.; Durecu, S.

2009-01-01

Antimony compounds have a wide range of industrial applications, particularly as additives in flame retardants. To ensure environmentally friendly waste incineration of Sb-rich wastes, it is essential to strengthen the knowledge about the fate of antimony and the potential formation of harmful species. Investigations should be conducted particularly in relation with the main operational parameters controlling the process, chiefly temperature, residence time and air supply in the oven and in the post-combustion zone, prior final adapted cleaning of the flue-gas stream. Experimental studies focusing on antimony behaviour were undertaken through laboratory-scale thermal treatment at 850 deg. C and 1100 deg. C of a Sb-rich halogenated waste, originating from the sector of flame retardants formulation. The configuration of our laboratory experimental device allowed to achieve only low oxidative conditions in the waste bed, but high oxidative strength coupled with high temperature and sufficient gas residence time in the post-combustion zone, as prescribed during the incineration of hazardous wastes. Atomic absorption spectroscopy was used to assess the partition of antimony in the different compartments of the process. The oxidation degree of antimony in the gas-phase was determined by the use of electrochemical techniques, namely polarography coupled with anodic stripping voltamperometry. The partition of antimony between the residual ash and the gas-phase under moderate oxidative conditions in the waste bed was constant, whatever the temperature: the volatilization rate for antimony was ∼64%, while a ∼36% fraction remained in the residual bottom ashes. But interestingly, while at 850 o C, antimony was mainly present in the gas-phase at a +III oxidation degree, an increase in temperature of 250 o C favoured the presence of antimony to its highest oxidation degree +V in the flue-gas stream, a valence known to be involved in less toxic species.

Behaviour of antimony during thermal treatment of Sb-rich halogenated waste

Energy Technology Data Exchange (ETDEWEB)

Klein, J. [Laboratoire Gestion des Risques et Environnement, 25 rue de Chemnitz, 68200 Mulhouse (France); Dorge, S., E-mail: sophie.dorge@uha.fr [Laboratoire Gestion des Risques et Environnement, 25 rue de Chemnitz, 68200 Mulhouse (France); Trouve, G. [Laboratoire Gestion des Risques et Environnement, 25 rue de Chemnitz, 68200 Mulhouse (France); Venditti, D.; Durecu, S. [TREDI Departement de Recherche, Technopole de Nancy-Brabois, 9 avenue de la Foret de Haye, BP 184, 54505 Vandoeuvre-les-Nancy (France)

2009-07-30

Antimony compounds have a wide range of industrial applications, particularly as additives in flame retardants. To ensure environmentally friendly waste incineration of Sb-rich wastes, it is essential to strengthen the knowledge about the fate of antimony and the potential formation of harmful species. Investigations should be conducted particularly in relation with the main operational parameters controlling the process, chiefly temperature, residence time and air supply in the oven and in the post-combustion zone, prior final adapted cleaning of the flue-gas stream. Experimental studies focusing on antimony behaviour were undertaken through laboratory-scale thermal treatment at 850 deg. C and 1100 deg. C of a Sb-rich halogenated waste, originating from the sector of flame retardants formulation. The configuration of our laboratory experimental device allowed to achieve only low oxidative conditions in the waste bed, but high oxidative strength coupled with high temperature and sufficient gas residence time in the post-combustion zone, as prescribed during the incineration of hazardous wastes. Atomic absorption spectroscopy was used to assess the partition of antimony in the different compartments of the process. The oxidation degree of antimony in the gas-phase was determined by the use of electrochemical techniques, namely polarography coupled with anodic stripping voltamperometry. The partition of antimony between the residual ash and the gas-phase under moderate oxidative conditions in the waste bed was constant, whatever the temperature: the volatilization rate for antimony was {approx}64%, while a {approx}36% fraction remained in the residual bottom ashes. But interestingly, while at 850 {sup o}C, antimony was mainly present in the gas-phase at a +III oxidation degree, an increase in temperature of 250 {sup o}C favoured the presence of antimony to its highest oxidation degree +V in the flue-gas stream, a valence known to be involved in less toxic species.

Sustainable waste management by production of activated carbon from agroforestry residues

Directory of Open Access Journals (Sweden)

Victor Ntuli

2013-01-01

Full Text Available Agroforestry waste presents a problem for disposal and negatively impacts on the environment if left to rot or burn. The aim of this study was to reduce environmental problems associated with agroforestry waste by promoting the innovative use of such waste in the production of activated carbons (ACs using a low-cost production technique, and ultimately delivering more affordable water and effluent treatment adsorbents. Four varieties of ACs from four different agroforestry materials – pine (Pinus contorta cones (PC, Abies (Abies cilicica seeds (AS, maple (Acer ginnala seeds (MS and peach (Prunus persica stones (PS – were prepared by single-step steam pyrolysis and characterised. The raw materials were evaluated for AC yield while the respective ACs were evaluated on the basis of iodine number, phenol specific area, ash content, pH, moisture content and removal of metal ions, nitrates and sulphates from aqueous solution. The AC yields for PS, PC, AS and MS were found to be 23.0%, 18.0%, 17.8% and 14.6%, respectively. The yield for PS (23% is within the specified commercial limits of 20% to 40%. The phenol specific areas of the ACs ranged between 381 m2/g and 415 m2/g higher than the commercial lower limit (300 m2/g generally specified. The ACs also showed the capacity to remove heavy metal ions from their aqueous solutions. Removal of both nitrates and sulphates in raw water was greater than 50%. Although no quantitative analysis has been performed to date, it is envisaged that the production of AC from agroforestry wastes can contribute to the sustainable management of environmental pollution by these residues and the concomitant delivery of cheaper adsorbents.

Final treatment of liquid radioactive wastes

International Nuclear Information System (INIS)

Svolik, S.

2004-01-01

Final treatment of liquid radioactive wastes which are produced by 1 st and 2 nd bloc of the Mochovce NPP, prepares the NPP in its natural range. The purpose of the equipment is liquidation of wastes, which are formed at production. Wastes are warehoused in the building of active auxiliary plants in the present time, where are reservoirs in which they are deposited. Because they are already feeling and in 2006 year they should be filled definitely, it is necessary to treat them in that manner, so as they may be liquidated. Therefore the Board of directors of the Slovenske elektrarne has disposed about construction of final treatment of liquid radioactive wastes in the Mochovce NPP. Because of transport the wastes have to be treated in the locality of power plant. Technically, the final treatment of the wastes will be interconnected with building of active operation by bridges. These bridges will transport the wastes for treatment into processing centre

Thermal Treatment of Iron Oxide Stabilized APC Residues from Waste Incineration and the Effect on Heavy Metal Binding

DEFF Research Database (Denmark)

Sørensen, Mette Abildgaard; Stackpoole, M.; Bender-Koch, C.

2000-01-01

Iron oxide stabilized APC residues from MSWI were heat treated at 600°C and 900°C. The thermal treatments resulted in a change in product stability by forcing a transformation in the mineralogical structures of the products. The treatments, moreover, simulated somewhat the natural aging processes...

Treatment of radioactive wastes

International Nuclear Information System (INIS)

Machida, Chuji

1976-01-01

Japan Atomic Energy Research Institute (JAERI) is equipped with such atomic energy facilities as a power test reactor, four research reactors, a hot laboratory, and radioisotope-producing factory. All the radioactive wastes but gas generated from these facilities are treated by the waste treatment facilities established in JAERI. The wastes carried into JAERI through Japan Radioisotope Association are also treated there. Low level water solution is treated with an evaporating apparatus, an ion-exchange apparatus, and a cohesive precipitating apparatus, while medium level solution is treated with an evaporating apparatus, and low level combustible solid is treated with an incinerating apparatus. These treated wastes and sludges are mixed with Portland cement in drum cans to solidify, and stored in a concrete pit. The correct classification and its indication as well as the proper packing for the wastes are earnestly demanded by the treatment facilities. (Kobatake, H.)

Control of spread of Augusta disease caused by tobacco necrosis virus in tulip by composting residual waste of small bulbs, tunics, roots and soil debris

NARCIS (Netherlands)

Asjes, C.J.; Barnhoorn, G.J.

2002-01-01

In this study the elimination of the infectious virus/fungus complex of tobacco necrosis virus (TNV; cause of Augusta disease in tulip) and Olpidium brassicae in different soil types and residual waste material of soil debris, small tulip bulbs, roots and tunics by temperature treatments of

TANK FARM CLOSURE - A NEW TWIST ON REGULATORY STRATEGIES FOR CLOSURE OF WASTE TANK RESIDUALS FOLLOWING NUREG

International Nuclear Information System (INIS)

LEHMAN LL

2008-01-01

Waste from a number of single-shell tanks (SST) at the U.S. Department of Energy's (DOE) Hanford Site has been retrieved by CH2M HILL Hanford Group to fulfill the requirements of the 'Hanford Federal Facility Agreement and Consent Order (HFFACO) [1]. Laboratory analyses of the Hanford tank residual wastes have provided concentration data which will be used to determine waste classification and disposal options for tank residuals. The closure of tank farm facilities remains one of the most challenging activities faced by the DOE. This is due in part to the complicated regulatory structures that have developed. These regulatory structures are different at each of the DOE sites, making it difficult to apply lessons learned from one site to the next. During the past two years with the passage of the Section 3116 of the 'Ronald Reagan Defense Authorization Act of 2005' (NDAA) [2] some standardization has emerged for Savannah River Site and the Idaho National Laboratory tank residuals. Recently, with the issuance of 'NRC Staff Guidance for Activities Related to US. Department of Energy Waste Determinations' (NUREG-1854) [3] more explicit options may be considered for Hanford tank residuals than are presently available under DOE Orders. NUREG-1854, issued in August 2007, contains several key pieces of information that if utilized by the DOE in the tank closure process, could simplify waste classification and streamline the NRC review process by providing information to the NRC in their preferred format. Other provisions of this NUREG allow different methods to be applied in determining when waste retrieval is complete by incorporating actual project costs and health risks into the calculation of 'technically and economically practical'. Additionally, the NUREG requires a strong understanding of the uncertainties of the analyses, which given the desire of some NRC/DOE staff may increase the likelihood of using probabilistic approaches to uncertainty analysis. The purpose

Antimicrobial residues in animal waste and water resources proximal to large-scale swine and poultry feeding operations

Science.gov (United States)

Campagnolo, E.R.; Johnson, K.R.; Karpati, A.; Rubin, C.S.; Kolpin, D.W.; Meyer, M.T.; Esteban, J. Emilio; Currier, R.W.; Smith, K.; Thu, K.M.; McGeehin, M.

2002-01-01

Expansion and intensification of large-scale animal feeding operations (AFOs) in the United States has resulted in concern about environmental contamination and its potential public health impacts. The objective of this investigation was to obtain background data on a broad profile of antimicrobial residues in animal wastes and surface water and groundwater proximal to large-scale swine and poultry operations. The samples were measured for antimicrobial compounds using both radioimmunoassay and liquid chromatography/electrospray ionization-mass spectrometry (LC/ESI-MS) techniques. Multiple classes of antimicrobial compounds (commonly at concentrations of >100 μg/l) were detected in swine waste storage lagoons. In addition, multiple classes of antimicrobial compounds were detected in surface and groundwater samples collected proximal to the swine and poultry farms. This information indicates that animal waste used as fertilizer for crops may serve as a source of antimicrobial residues for the environment. Further research is required to determine if the levels of antimicrobials detected in this study are of consequence to human and/or environmental ecosystems. A comparison of the radioimmunoassay and LC/ESI-MS analytical methods documented that radioimmunoassay techniques were only appropriate for measuring residues in animal waste samples likely to contain high levels of antimicrobials. More sensitive LC/ESI-MS techniques are required in environmental samples, where low levels of antimicrobial residues are more likely.

Antimicrobial residues in animal waste and water resources proximal to large-scale swine and poultry feeding operations.

Science.gov (United States)

Campagnolo, Enzo R; Johnson, Kammy R; Karpati, Adam; Rubin, Carol S; Kolpin, Dana W; Meyer, Michael T; Esteban, J Emilio; Currier, Russell W; Smith, Kathleen; Thu, Kendall M; McGeehin, Michael

2002-11-01

Expansion and intensification of large-scale animal feeding operations (AFOs) in the United States has resulted in concern about environmental contamination and its potential public health impacts. The objective of this investigation was to obtain background data on a broad profile of antimicrobial residues in animal wastes and surface water and groundwater proximal to large-scale swine and poultry operations. The samples were measured for antimicrobial compounds using both radioimmunoassay and liquid chromatography/electrospray ionization-mass spectrometry (LC/ESI-MS) techniques. Multiple classes of antimicrobial compounds (commonly at concentrations of > 100 microg/l) were detected in swine waste storage lagoons. In addition, multiple classes of antimicrobial compounds were detected in surface and groundwater samples collected proximal to the swine and poultry farms. This information indicates that animal waste used as fertilizer for crops may serve as a source of antimicrobial residues for the environment. Further research is required to determine if the levels of antimicrobials detected in this study are of consequence to human and/or environmental ecosystems. A comparison of the radioimmunoassay and LC/ESI-MS analytical methods documented that radioimmunoassay techniques were only appropriate for measuring residues in animal waste samples likely to contain high levels of antimicrobials. More sensitive LC/ESI-MS techniques are required in environmental samples, where low levels of antimicrobial residues are more likely.

Technologies 1995: environment and wastes treatment

International Nuclear Information System (INIS)

Anon.

1995-03-01

From new technical or scientific developments, new products launching, and markets evolutions, this catalog gives informations selection on research and development projects, new fabrication processes, activities and plants strategies, licences or technology transfers opportunities. The covered fields are: atmospheric pollution controls, water and liquid wastes treatment, polluted soils treatments, noise and odors treatments, municipal and industrial wastes treatments (metal, plastic, paper, glass), clean materials and technologies, radioactive wastes, and european cooperation programs. (A.B.)

Fermentation of household wastes and industrial waste water; Vergaerung von haeuslichen Abfaellen und Industrieabwaessern

Energy Technology Data Exchange (ETDEWEB)

Edelmann, W [Arbeitsgemeinschaft Bioenergie ' arbi' , Maschwanden (Switzerland); Engeli, H [Probag AG, Dietikon (Switzerland); Glauser, M [Biol-Conseils SA, Neuchatel (Switzerland); Hofer, H [HTH-Verfahrenstechnik, Winterthur (Switzerland); Membrez, Y [EREP SA, Aclens (Switzerland); Meylan, J -H [Lausanne (Switzerland); Schwitzguebel, J -P [Swiss Federal Institute of Technology (EPFL), Genie biologique, Lausanne (Switzerland)

1993-07-01

This comprehensive brochure reviews various technologies for the environment-friendly treatment of organic wastes and residues. The principles of anaerobic digestion are discussed. Authorities, planners and engineers concerned with waste treatment are provided with an overview of current technology in the organic wastes area. The brochure emphasises the importance of fermentation processes in waste treatment, discusses the legal pre-requisites for biogas production, lists the biological and process-oriented fundamentals of fermentation and examines the energy potential of biogenic wastes and waste water. Further, details are given on the treatment of both industrial waste water and solid organic wastes and, finally, the economics of fermentation is examined. Useful data is presented in table form and the various processes described are illustrated by schematics and flow diagrams. An appendix lists suggestions for further reading on the subject.

Environmental impacts of residual municipal solid waste incineration: a comparison of 110 French incinerators using a life cycle approach.

Science.gov (United States)

Beylot, Antoine; Villeneuve, Jacques

2013-12-01

Incineration is the main option for residual Municipal Solid Waste treatment in France. This study compares the environmental performances of 110 French incinerators (i.e., 85% of the total number of plants currently in activity in France) in a Life Cycle Assessment perspective, considering 5 non-toxic impact categories: climate change, photochemical oxidant formation, particulate matter formation, terrestrial acidification and marine eutrophication. Mean, median and lower/upper impact potentials are determined considering the incineration of 1 tonne of French residual Municipal Solid Waste. The results highlight the relatively large variability of the impact potentials as a function of the plant technical performances. In particular, the climate change impact potential of the incineration of 1 tonne of waste ranges from a benefit of -58 kg CO2-eq to a relatively large burden of 408 kg CO2-eq, with 294 kg CO2-eq as the average impact. Two main plant-specific parameters drive the impact potentials regarding the 5 non-toxic impact categories under study: the energy recovery and delivery rate and the NOx process-specific emissions. The variability of the impact potentials as a function of incinerator characteristics therefore calls for the use of site-specific data when required by the LCA goal and scope definition phase, in particular when the study focuses on a specific incinerator or on a local waste management plan, and when these data are available. Copyright © 2013 Elsevier Ltd. All rights reserved.

Composition of municipal solid waste in Denmark

DEFF Research Database (Denmark)

Edjabou, Vincent Maklawe Essonanawe; Petersen, Claus; Scheutz, Charlotte

2014-01-01

Data for the composition of municipal solid waste is a critical basis for any assessment of waste technologies and waste management systems. The detailed quantification of waste fractions is absolutely needed for a better technological development of waste treatment. The current waste composition...... comparability to characterize municipal solid waste. This methodology was applied to residual waste collected from 1,442 households in three municipalities in Denmark. The main fractions contributing to the residual household waste were food waste and miscellaneous waste. Statistical analysis suggested...... of standardised and commonly accepted waste characterization methodologies, various approaches have been reported in literature. This limits both comparability and applicability of the results. The purpose of this study was to introduce a consistent methodology that reduces uncertainties and ensures data...

Napropamide residues in runoff and infiltration water from pepper production.

Science.gov (United States)

Antonious, George F; Patterson, Matthew A

2005-01-01

A field study was conducted on a Lowell silty loam soil of 2.7% organic matter at the Kentucky State University Research Farm, Franklin County, Kentucky. Eighteen universal soil loss equation (USLE) standard plots (22 x 3.7 m each) were established on a 10% slope. Three soil management practices were used: (i) class-A biosolids (sewage sludge), (ii) yard waste compost, each mixed with native soil at a rate of 50 ton acre(-1) on a dry-weight basis, and (iii) a no-mulch (NM) treatment (rototilled bare soil), used for comparison purposes. Devrinol 50-DF "napropamide" [N,N-diethyl-2-(1-naphthyloxy) propionamide] was applied as a preemergent herbicide, incorporated into the soil surface, and the plots were planted with 60-day-old sweet bell pepper seedlings. Napropamide residues one hour following spraying averaged 0.8, 0.4, and 0.3 microg g(-1) dry soil in sewage sludge, yard waste compost, and no-mulch treatments, respectively. Surface runoff water, runoff sediment, and napropamide residues in runoff were significantly reduced by the compost and biosolid treatments. Yard waste compost treatments increased water infiltration and napropamide residues in the vadose zone compared to sewage sludge and NM treatments. Total pepper yields from yard waste compost amended soils (9187 lbs acre(-1)) was significantly higher (P soil amended with class-A biosolids (6984 lbs acre(-1)) or the no-mulch soil (7162 lbs acre(-1)).

Reduction of heavy metals in residues from the dismantling of waste electrical and electronic equipment before incineration

International Nuclear Information System (INIS)

Long, Yu-Yang; Feng, Yi-Jian; Cai, Si-Shi; Hu, Li-Fang; Shen, Dong-Sheng

2014-01-01

Highlights: • The highest metal reduction occurs at a 2.36 mm sieving size. • Washing promotes heavy metal recycling without secondary pollution. • Sieving and washing are environmentally friendly pretreatments for WEEE wastes. - Abstract: Residues disposal from the dismantling of waste electrical and electronic equipment are challenging because of the large waste volumes, degradation-resistance, low density and high heavy metal content. Incineration is advantageous for treating these residues but high heavy metal contents may exist in incinerator input and output streams. We have developed and studied a specialized heavy metal reduction process, which includes sieving and washing for treating residues before incineration. The preferable screen aperture for sieving was found to be 2.36 mm (8 meshes) in this study; using this screen aperture resulted in the removal of approximately 47.2% Cu, 65.9% Zn, 26.5% Pb, 55.4% Ni and 58.8% Cd from the residues. Subsequent washing further reduces the heavy metal content in the residues larger than 2.36 mm, with preferable conditions being 400 rpm rotation speed, 5 min washing duration and liquid-to-solid ratio of 25:1. The highest cumulative removal efficiencies of Cu, Zn, Pb, Ni and Cd after sieving and washing reached 81.1%, 61.4%, 75.8%, 97.2% and 72.7%, respectively. The combined sieving and washing process is environmentally friendly, can be used for the removal of heavy metals from the residues and has benefits in terms of heavy metal recycling

Reduction of heavy metals in residues from the dismantling of waste electrical and electronic equipment before incineration

Energy Technology Data Exchange (ETDEWEB)

Long, Yu-Yang; Feng, Yi-Jian; Cai, Si-Shi [Zhejiang Provincial Key Laboratory of Solid Waste Treatment and Recycling, School of Environmental Science and Engineering, Zhejiang Gongshang University, Hangzhou 310012 (China); Hu, Li-Fang [College of Quality and Safety Engineering, China Jiliang University, Hangzhou 310018 (China); Shen, Dong-Sheng, E-mail: shends@zju.edu.cn [Zhejiang Provincial Key Laboratory of Solid Waste Treatment and Recycling, School of Environmental Science and Engineering, Zhejiang Gongshang University, Hangzhou 310012 (China)

2014-05-01

Highlights: • The highest metal reduction occurs at a 2.36 mm sieving size. • Washing promotes heavy metal recycling without secondary pollution. • Sieving and washing are environmentally friendly pretreatments for WEEE wastes. - Abstract: Residues disposal from the dismantling of waste electrical and electronic equipment are challenging because of the large waste volumes, degradation-resistance, low density and high heavy metal content. Incineration is advantageous for treating these residues but high heavy metal contents may exist in incinerator input and output streams. We have developed and studied a specialized heavy metal reduction process, which includes sieving and washing for treating residues before incineration. The preferable screen aperture for sieving was found to be 2.36 mm (8 meshes) in this study; using this screen aperture resulted in the removal of approximately 47.2% Cu, 65.9% Zn, 26.5% Pb, 55.4% Ni and 58.8% Cd from the residues. Subsequent washing further reduces the heavy metal content in the residues larger than 2.36 mm, with preferable conditions being 400 rpm rotation speed, 5 min washing duration and liquid-to-solid ratio of 25:1. The highest cumulative removal efficiencies of Cu, Zn, Pb, Ni and Cd after sieving and washing reached 81.1%, 61.4%, 75.8%, 97.2% and 72.7%, respectively. The combined sieving and washing process is environmentally friendly, can be used for the removal of heavy metals from the residues and has benefits in terms of heavy metal recycling.

Development of radioactive waste treatment technique

International Nuclear Information System (INIS)

Kikuchi, Makoto; Amamiya, Shigeru; Yusa, Hideo.

1984-01-01

The techniques of radioactive waste treatment are generally reviewed, placing emphasis on volume reduction and solidification techniques. After a brief description on the general process of radioactive waste treatment, some special technologies being developed by Hitachi Ltd. are explained. From the viewpoints of the volume reduction, long term management and final disposal of wastes, the pelletization of dried waste and the solidification with inorganic substances are considered. One of the features of the pelletization system is to treat various kinds of wastes such as concentrated liquid wastes and used resins by the same system. The flow diagram of the system and its special features are shown. The volume reduction achieved by this system as compared to the conventional method is about 1/7. The first commercial plant for the treatment of concentrated liquid waste is scheduled to begin operation in June, 1984. As for the solidification technique for waste disposal, the use of cement glass is considered. The solidification system being developed is shortly described. (Aoki, K.)

Assessment of long-term pH developments in leachate from waste incineration residues

DEFF Research Database (Denmark)

Astrup, Thomas; Jakobsen, Rasmus; Christensen, Thomas Højlund

2006-01-01

influenced by changes in pH over time. The paper presents an approach for assessing pH changes in leachate from municipal solid waste incineration (MSWI) air-pollution-control (APC) residues. Residue samples were subjected to a stepwise batch extraction method in order to obtain residue samples at a range...... of pH Values (similar to common pH-dependence tests), and then on these samples to determine leaching of alkalinity as well as remaining solid phase alkalinity. On a range of APC residues covering various pretreatment and disposal options, this procedure was used to determine leachable and residual...... alkalinity as a function of pH. Mass balance calculations for typical disposal scenarios were used to provide data on pH as a function of the liquid-to-solid (L/S) ratio in the leaching system. Regardless of residue type and pretreatment, pH was found to stay above 7 for L/S ratios up to about 2000 L kg(-1...

Proceedings of emerging technologies for hazardous waste management

International Nuclear Information System (INIS)

Tedder, D.W.

1992-01-01

This book contains proceedings of emerging technologies for hazardous waste management. Topics covered include: Low-temperature oxidation of organic chemical wastes; Advanced waste minimization strategies; Treatment of manufactured gas plant (MGP) and similar wastes; Bioremediation of soils and sediments; Advances in radioactive waste treatment; Computer aides approaches to hazardous waste management; Advances in soil remediation; Low-temperature oxidation of organic chemical waste; Boremediation: Micro, meso, and macro-scale processes; In situ remediation techniques; Treatment of hazardous organics with radiation or solar energy; Technologies for management of municipal waste combustion residues; Environmental restoration and waste management; and Advanced separation and stabilization technologies

Evolution Of Chemical Conditions And Estimated Plutonium Solubility In The Residual Waste Layer During Post-Closure Aging Of Tank 18

International Nuclear Information System (INIS)

Denham, M.

2012-01-01

evolution. In Denham (2007, Rev. 1), the solubilities in the oxidized regions were estimated at Eh values in equilibrium with dissolved oxygen. Here, these are considered to be maximum possible solubilities because Eh values are unlikely to be in equilibrium with dissolved oxygen. More realistic Eh values are estimated here and plutonium solubilities calculated at these are considered more realistic. Apparent solubilities of plutonium that coprecipitated with iron phases are estimated from Pu:Fe ratios in Tank 18 residual waste and the solubilities of the host iron phases. The estimated plutonium solubilities are shown. Uncertainties in the grout simulations and plutonium solubility estimates are discussed. The primary uncertainty in the grout simulations is that little is known about the physical state of the grout as it ages. The simulations done here are pertinent to a porous medium, which may or may not be applicable to fractured grout, depending on the degree and nature of the fractures. Other uncertainties that are considered are the assumptions about the reducing capacity imparted by blast furnace slag, the effects of varying dissolved carbon dioxide and oxygen concentrations, and the treatment of silica in the simulations. The primary uncertainty in the estimates of plutonium solubility is that little is known about the exact form of plutonium in the residual waste. Other uncertainties include those inherent in the thermodynamic data, pH variations from those estimated in the grout simulations, the effects of the treatment of silica in the grout simulations, and the effect of varying total dissolved carbonate concentrations. The objective of this document is to update the model for solubility controls on release of plutonium from residual waste in closed F-Area waste tanks. The update is based on new information including a new proposed grout formulation, chemical analysis of Tank 18 samples and more current thermodynamic data for plutonium and grout minerals. In

Liquid Radioactive Wastes Treatment: A Review

Directory of Open Access Journals (Sweden)

Yung-Tse Hung

2011-05-01

Full Text Available Radioactive wastes are generated during nuclear fuel cycle operation, production and application of radioisotope in medicine, industry, research, and agriculture, and as a byproduct of natural resource exploitation, which includes mining and processing of ores, combustion of fossil fuels, or production of natural gas and oil. To ensure the protection of human health and the environment from the hazard of these wastes, a planned integrated radioactive waste management practice should be applied. This work is directed to review recent published researches that are concerned with testing and application of different treatment options as a part of the integrated radioactive waste management practice. The main aim from this work is to highlight the scientific community interest in important problems that affect different treatment processes. This review is divided into the following sections: advances in conventional treatment of aqueous radioactive wastes, advances in conventional treatment of organic liquid wastes, and emerged technological options.

Engineering evaluation of alternatives for the disposition of Niagara Falls Storage Site, its residues and wastes

International Nuclear Information System (INIS)

1984-01-01

The final disposition scenarios selected by DOE for assessment in this document are consistent with those stated in the Notice of Intent to prepare an Environmental Impact Statement (EIS) for the Niagara Falls Storage Site (NFSS) (DOE, 1983d) and the modifications to the alternatives resulting from the public scoping process. The scenarios are: take no action beyond interim remedial measures other than maintenance and surveillance of the NFSS; retain and manage the NFSS as a long-term waste management facility for the wastes and residues on the site; decontaminate, certify, and release the NFSS for other use, with long-term management of the wastes and residues at other DOE sites; and partially decontaminate the NFSS by removal and transport off site of only the more radioactive residues, and upgrade containment of the remaining wastes and residues on site. The objective of this document is to present to DOE the conceptual engineering, occupational radiation exposure, construction schedule, maintenance and surveillance requirements, and cost information relevant to design and implementation of each of the four scenarios. The specific alternatives within each scenario used as the basis for discussion in this document were evaluated on the bases of engineering considerations, technical feasibility, and regulatory requirements. Selected alternatives determined to be acceptable for each of the four final disposition scenarios for the NFSS were approved by DOE to be assessed and costed in this document. These alternatives are also the subject of the EIS for the NFSS currently being prepared by Argonne National Laboratory (ANL). 40 figures, 38 tables

Solid waste treatment processes for space station

Science.gov (United States)

Marrero, T. R.

1983-01-01

The purpose of this study was to evaluate the state-of-the-art of solid waste(s) treatment processes applicable to a Space Station. From the review of available information a source term model for solid wastes was determined. An overall system is proposed to treat solid wastes under constraints of zero-gravity and zero-leakage. This study contains discussion of more promising potential treatment processes, including supercritical water oxidation, wet air (oxygen) oxidation, and chemical oxidation. A low pressure, batch-type treament process is recommended. Processes needed for pretreatment and post-treatment are hardware already developed for space operations. The overall solid waste management system should minimize transfer of wastes from their collection point to treatment vessel.

Chemical treatment of mixed waste at the FEMP

International Nuclear Information System (INIS)

Honigford, L.; Sattler, J.; Dilday, D.; Cook, D.

1996-01-01

The Chemical Treatment Project is one in a series of projects implemented by the Fernald Environmental Management Project (FEMP) to treat mixed waste. The projects were initiated to address concerns regarding treatment capacity for mixed waste and to comply with requirements established by the Federal Facility Compliance Act. The Chemical Treatment Project is designed to utilize commercially available mobile technologies to perform treatment at the FEMP site. The waste in the Project consists of a variety of waste types with a wide range of hazards and physical characteristics. The treatment processes to be established for the waste types will be developed by a systematic approach including waste streams evaluation, projectization of the waste streams, and categorization of the stream. This information is utilized to determine the proper train of treatment which will be required to lead the waste to its final destination (i.e., disposal). This approach allows flexibility to manage a wide variety of waste in a cheaper, faster manner than designing a single treatment technology diverse enough to manage all the waste streams

Waste minimization promotes biophysical treatment of complex petrochemical wastes in Israel

Energy Technology Data Exchange (ETDEWEB)

Lebel, A [Invirotreat International Ltd., Fulleron, CA (United States); Raveh, A [Raveh Ecology Ltd., Haifa (Israel)

1994-12-31

This work describes a full-scale waste treatment system which was put into operation in a petrochemical manufacturing plant in Israel for the purpose of detoxifying its complex organic waste stream. The treatment plant design incorporates an innovative waste management approach to accommodate the limited space allocated for the facility. Initial performance data indicate a high efficient inorganic waste reduction. 4 refs., 6 figs., 2 tabs.

Waste minimization promotes biophysical treatment of complex petrochemical wastes in Israel

Energy Technology Data Exchange (ETDEWEB)

Lebel, A. [Invirotreat International Ltd., Fulleron, CA (United States); Raveh, A. [Raveh Ecology Ltd., Haifa (Israel)

1993-12-31

This work describes a full-scale waste treatment system which was put into operation in a petrochemical manufacturing plant in Israel for the purpose of detoxifying its complex organic waste stream. The treatment plant design incorporates an innovative waste management approach to accommodate the limited space allocated for the facility. Initial performance data indicate a high efficient inorganic waste reduction. 4 refs., 6 figs., 2 tabs.

Washing of waste prior to landfilling.

Science.gov (United States)

Cossu, Raffaello; Lai, Tiziana

2012-05-01

The main impact produced by landfills is represented by the release of leachate emissions. Waste washing treatment has been investigated to evaluate its efficiency in reducing the waste leaching fraction prior to landfilling. The results of laboratory-scale washing tests applied to several significant residues from integrated management of solid waste are presented in this study, specifically: non-recyclable plastics from source separation, mechanical-biological treated municipal solid waste and a special waste, automotive shredded residues. Results obtained demonstrate that washing treatment contributes towards combating the environmental impacts of raw wastes. Accordingly, a leachate production model was applied, leading to the consideration that the concentrations of chemical oxygen demand (COD) and total Kjeldahl nitrogen (TKN), parameters of fundamental importance in the characterization of landfill leachate, from a landfill containing washed wastes, are comparable to those that would only be reached between 90 and 220years later in the presence of raw wastes. The findings obtained demonstrated that washing of waste may represent an effective means of reducing the leachable fraction resulting in a consequent decrease in landfill emissions. Further studies on pilot scale are needed to assess the potential for full-scale application of this treatment. Copyright © 2012 Elsevier Ltd. All rights reserved.

Upfront delisting petition for vitrified M-Area plating line waste

International Nuclear Information System (INIS)

Pickett, J.B.

1996-09-01

This petition seeks exclusion of certain solid wastes generated at the Savannah River Site near Aiken South Carolina from the lists of Resource Conservation and Recovery Act (RCRA) hazardous wastes contained in 40 CFR 261.24 and 40 CFR261.31. DOE-SRS is petitioning the EPA, to exclude upfront treatment residues, generated by a vitrification process of a listed F006 mixed (hazardous and radioactive) waste from the list of hazardous wastes identified in 40 CFR Part 261.3. The resultant treatment residues will be regulated by 40 CFR 261.3(c)(2)(i) until delisted. This petition will show that the resultant treatment residue will not: meet any criteria for which it was listed; exhibit any hazardous waste characteristics as identified in 40 CFR 261 Subpart C; and will not exhibit any other factors or additional constituents which would render it to be considered a RCRA hazardous waste. This request for an upfront petition is based upon: analytical evaluation of the characteristics of the untreated waste; facility and process descriptions; and data from bench-scale (crucible studies) and a small scale melter demonstration

Nuclear fuel cycle waste recycling technology deverlopment - Radioactive metal waste recycling technology development

International Nuclear Information System (INIS)

Oh, Won Zin; Moon, Jei Kwon; Jung, Chong Hun; Park, Sang Yoon

1998-08-01

With relation to recycling of the radioactive metal wastes which are generated during operation and decommissioning of nuclear facilities, the following were described in this report. 1. Analysis of the state of the art on the radioactive metal waste recycling technologies. 2. Economical assessment on the radioactive metal waste recycling. 3. Process development for radioactive metal waste recycling, A. Decontamination technologies for radioactive metal waste recycling. B. Decontamination waste treatment technologies, C. Residual radioactivity evaluation technologies. (author). 238 refs., 60 tabs., 79 figs

Integrated nonthermal treatment system study

International Nuclear Information System (INIS)

Biagi, C.; Bahar, D.; Teheranian, B.; Vetromile, J.; Quapp, W.J.; Bechtold, T.; Brown, B.; Schwinkendorf, W.; Swartz, G.

1997-01-01

This report presents the results of a study of nonthermal treatment technologies. The study consisted of a systematic assessment of five nonthermal treatment alternatives. The treatment alternatives consist of widely varying technologies for safely destroying the hazardous organic components, reducing the volume, and preparing for final disposal of the contact-handled mixed low-level waste (MLLW) currently stored in the US Department of Energy complex. The alternatives considered were innovative nonthermal treatments for organic liquids and sludges, process residue, soil and debris. Vacuum desorption or various washing approaches are considered for treatment of soil, residue and debris. Organic destruction methods include mediated electrochemical oxidation, catalytic wet oxidation, and acid digestion. Other methods studied included stabilization technologies and mercury separation of treatment residues. This study is a companion to the integrated thermal treatment study which examined 19 alternatives for thermal treatment of MLLW waste. The quantities and physical and chemical compositions of the input waste are based on the inventory database developed by the US Department of Energy. The Integrated Nonthermal Treatment Systems (INTS) systems were evaluated using the same waste input (2,927 pounds per hour) as the Integrated Thermal Treatment Systems (ITTS). 48 refs., 68 figs., 37 tabs

Integrated nonthermal treatment system study

Energy Technology Data Exchange (ETDEWEB)

Biagi, C.; Bahar, D.; Teheranian, B.; Vetromile, J. [Morrison Knudsen Corp. (United States); Quapp, W.J. [Nuclear Metals (United States); Bechtold, T.; Brown, B.; Schwinkendorf, W. [Lockheed Martin Idaho Technologies Co., Idaho Falls, ID (United States); Swartz, G. [Swartz and Associates (United States)

1997-01-01

This report presents the results of a study of nonthermal treatment technologies. The study consisted of a systematic assessment of five nonthermal treatment alternatives. The treatment alternatives consist of widely varying technologies for safely destroying the hazardous organic components, reducing the volume, and preparing for final disposal of the contact-handled mixed low-level waste (MLLW) currently stored in the US Department of Energy complex. The alternatives considered were innovative nonthermal treatments for organic liquids and sludges, process residue, soil and debris. Vacuum desorption or various washing approaches are considered for treatment of soil, residue and debris. Organic destruction methods include mediated electrochemical oxidation, catalytic wet oxidation, and acid digestion. Other methods studied included stabilization technologies and mercury separation of treatment residues. This study is a companion to the integrated thermal treatment study which examined 19 alternatives for thermal treatment of MLLW waste. The quantities and physical and chemical compositions of the input waste are based on the inventory database developed by the US Department of Energy. The Integrated Nonthermal Treatment Systems (INTS) systems were evaluated using the same waste input (2,927 pounds per hour) as the Integrated Thermal Treatment Systems (ITTS). 48 refs., 68 figs., 37 tabs.

Liquid waste treatment system. Final report

International Nuclear Information System (INIS)

Baker, M.N.; Houston, H.M.

1999-01-01

Pretreatment of high-level liquid radioactive waste (HLW) at the West Valley Demonstration Project (WVDP) involved three distinct processing operations: decontamination of liquid HLW in the Supernatant Treatment System (STS); volume reduction of decontaminated liquid in the Liquid Waste Treatment System (LWTS); and encapsulation of resulting concentrates into an approved cement waste form in the Cement Solidification System (CSS). Together, these systems and operations made up the Integrated Radwaste Treatment System (IRTS)

Environmental assessment for the treatment of Class A low-level radioactive waste and mixed low-level waste generated by the West Valley Demonstration Project

International Nuclear Information System (INIS)

1995-11-01

The U.S. Department of Energy (DOE) is currently evaluating low-level radioactive waste management alternatives at the West Valley Demonstration Project (WVDP) located on the Western New York Nuclear Service Center (WNYNSC) near West Valley, New York. The WVDP's mission is to vitrify high-level radioactive waste resulting from commercial fuel reprocessing operations that took place at the WNYNSC from 1966 to 1972. During the process of high-level waste vitrification, low-level radioactive waste (LLW) and mixed low-level waste (MILLW) will result and must be properly managed. It is estimated that the WVDP's LLW storage facilities will be filled to capacity in 1996. In order to provide sufficient safe storage of LLW until disposal options become available and partially fulfill requirements under the Federal Facilities Compliance Act (FFCA), the DOE is proposing to use U.S. Nuclear Regulatory Commission-licensed and permitted commercial facilities in Oak Ridge, Tennessee; Clive, Utah; and Houston, Texas to treat (volume-reduce) a limited amount of Class A LLW and MLLW generated from the WVDP. Alternatives for ultimate disposal of the West Valley LLW are currently being evaluated in an environmental impact statement. This proposed action is for a limited quantity of waste, over a limited period of time, and for treatment only; this proposal does not include disposal. The proposed action consists of sorting, repacking, and loading waste at the WVDP; transporting the waste for commercial treatment; and returning the residual waste to the WVDP for interim storage. For the purposes of this assessment, environmental impacts were quantified for a five-year operating period (1996 - 2001). Alternatives to the proposed action include no action, construction of additional on-site storage facilities, construction of a treatment facility at the WVDP comparable to commercial treatment, and off-site disposal at a commercial or DOE facility

Hazardous Waste Treatment Facility and skid-mounted treatment systems at Los Alamos

International Nuclear Information System (INIS)

Lussiez, G.W.; Zygmunt, S.J.

1994-01-01

To centralize treatment, storage, and areas for hazardous wastes, Los Alamos National Laboratory has designed a 1115 m2 hazardous waste treatment facility. The facility will house a treatment room for each of four kinds of wastes: nonradioactive characteristic wastes, nonradioactive listed wastes, radioactive characteristic wastes, and radioactive listed wastes. The facility will be used for repacking labpacks; bulking small organic waste volumes; processing scintillation vials; treating reactives such as lithium hydride and pyrophoric uranium; treating contaminated solids such as barium sand; treating plating wastes and other solutions with heavy metals and oxidizing organics: Separate treatment rooms will allow workers to avoid mixing waste types and prevent cross-contamination. The ventilation air from the treatment areas may contain hazardous or radioactive dust. Gas may also leak from process equipment. The gas treatment process includes separating solids and gases and neutralization or adsorption of the hazardous gases. The ventilation air from each room will first be filtered before being scrubbed in a common gas caustic scrubber on an outside pad. There are two levels of exhaust in each treatment room, one for heavy gases and another for light gases. Several features help mitigate or eliminate hazards due to spills and releases: each treatment room is sealed and under slight negative pressure; each room has its own HEPA filtration; to avoid mixing of incompatible wastes and reagents, portable individual spill-containment trays are used for skids, to limit the danger of spills, the waste is directly transferred from outside storage to the treatment room; to mitigate the consequences of a gas release in the room, mobile hoods are connected to the exhaust-air treatment system; the floor, walls, ceilings, fixtures, ducts, and piping are made of acid-resistant material or are coated

Leaching from municipal solid waste incineration residues

Energy Technology Data Exchange (ETDEWEB)

Hyks, J.

2008-02-15

Leaching of pollutants from Municipal Solid Waste Incineration (MSWI) residues has been investigated combining a range of laboratory leaching experiments with geochemical modeling. Special attention was paid to assessing the applicability of laboratory data for subsequent modeling with respect to presumed full-scale conditions; both sample pretreatment and actual influence of leaching conditions on the results of laboratory experiments were considered. It was shown that sample pretreatment may have large impact on leaching test data. In particular, a significant fraction of Pb was shown mobile during the washing of residues with water. In addition, drying of residues (i.e. slow oxidation) prior to leaching experiments increased the leaching of Cr significantly. Significant differences regarding the leaching behavior of individual elements with respect to (non)equilibrium conditions in column percolation experiments were observed in the study. As a result, three groups of elements were identified based on the predominant leaching control and the influence of (non)equilibrium on the results of the laboratory column experiments: I. Predominantly availability-controlled elements (e.g. Na, K, Cl) II. Solubility-controlled elements (e.g. Ca, S, Si, Al, Ba, and Zn) III. Complexation-controlled elements (e.g. Cu and Ni) With respect to the above groups it was suggested that results of laboratory column experiments can, with consideration, be used to estimate full-scale leaching of elements from Group I and II. However, in order to avoid large underestimations in the assessment of leaching from Group III, it is imperative to describe the time-dependent transport of dissolved organic carbon (DOC) in the tested system or to minimize the physical non-equilibrium during laboratory experiments (e.g. bigger column, slower flow velocity). Forward geochemical modeling was applied to simulate long-term release of elements from a MSWI air-pollution-control residue. Leaching of a

Impact of imidacloprid residues on the development of Eisenia fetida during vermicomposting of greenhouse plant waste.

Science.gov (United States)

Fernández-Gómez, Manuel J; Romero, Esperanza; Nogales, Rogelio

2011-09-15

Pesticide application in agriculture causes residues in post-harvest plant waste at different concentrations. Knowledge concerning how pesticide concentrations in such waste affect earthworms is essential for recycling greenhouse plant debris through vermicomposting. Here, we have evaluated the effects of imidacloprid (IMD) residues on earthworms (Eisenia fetida) during the vermicomposting of plant waste from greenhouse crops in Spain. Before, the effect of different IMD concentrations on earthworms was tested using cattle manure as an optimum waste for worm development. The results after using cattle manure indicate that IMD dose ≥ 5 mg kg(-1) hinders worm growth and even causes death, whereas IMD dose ≤ 2 mg IMD kg(-1) allows worm growth similar to control but impedes reproduction. The results from the vermicomposting of plant waste reveal that IMD inhibits adequate worm growth and increases mortality. Although 89% worms became sexually mature in substrate containing 2 mg IMD kg(-1), they did not produce cocoons. IMD also affected microorganisms harboured in the substrates for vermicomposting, as indicated by the reduction in their dehydrogenase activity. This enzyme activity was restored after vermicomposting. This study provides a sound basis for the vermicomposting of pesticide-contaminated plant waste. Copyright © 2011 Elsevier B.V. All rights reserved.

Conflicts concerning sites for waste treatment and waste disposal plants

International Nuclear Information System (INIS)

Werbeck, N.

1993-01-01

The erection of waste treatment and waste disposal flants increasingly meets with the disapproval of local residents. This is due to three factors: Firstly, the erection and operation of waste treatment plants is assumed to necessarily entail harmful effects and risks, which may be true or may not. Secondly, these disadvantages are in part considered to be non-compensable. Thirdly, waste treatment plants have a large catchment area, which means that more people enjoy their benefits than have to suffer their disadvantages. If residents in the vicinity of such plants are not compensated for damage sustained or harmed in ways that cannot be compensated for it becomes a rational stance for them, while not objecting to waste treatment and waste disposal plants in principle to object to their being in their own neighbourhood. The book comprehensively describes the subject area from an economic angle. The causes are analysed in detail and an action strategy is pointed, out, which can help to reduce acceptance problems. The individual chapters deal with emissions, risk potentials, optimization calculus considering individual firms or persons and groups of two or more firms or persons, private-economy approaches for the solving of site selection conflicts, collective decision-making. (orig./HSCH) [de

An assessment of off-gas treatment technologies for application to thermal treatment of Department of Energy wastes

International Nuclear Information System (INIS)

Dalton, J.D.; Gillins, R.L.; Harris, T.L.; Wollerman, A.L.

1992-09-01

The purpose of this report is to describe available air pollution control technologies for pollutants generated by thermal treatment of DOE wastes. A basic process for selecting air pollution control devices is summarized. Types of air pollutants generated by thermal treatment units are described, as well as the factors that influence the types and quantities of pollutants generated. This report also reviews applicable regulatory emission requirements. A listing of available and emerging air pollution control technologies and a brief introduction to the basic engineering principles involved in collecting each of the pollutants are presented. Section 7 of this report contains two types of evaluations for air pollution control devices. First, comparative evaluations of individual technologies are presented, based upon criteria generally relevant to DOE facilities. Using this evaluation system, the spray dryer absorber received the highest rating for acid-gas removal; high-efficiency particulate air (HEPA) filters received the highest rating for particulate removal; activated carbon adsorption received the highest rating for the removal of both toxic metals and residual hydrocarbons; and selective catalytic reduction received the highest rating for nitrogen oxide abatement. Also evaluated in Sect. 7 is the expected performance of different types of pollution control systems on two hypothetical waste streams. The waste streams were defined based upon typical DOE wastes and thermal treatment technologies. Section 8 presents conclusions for this report. Two appendixes are included with this report. The first appendix contains a brief description of all the technologies evaluated and the second lists of some of the vendors for each of the technologies that was evaluated

Rad-waste treatment

International Nuclear Information System (INIS)

1996-01-01

The spent fuel coming from Slovak NPPs have partially been transported to the former Soviet Union, and a part of it is stored in an interim spent fuel wet storage. In compliance with the worldwide practices, further medium-term possibilities of storing in dry storages are under preparation. Disposal of a spent fuel and other high-level active wastes in a deep geological formation repository is the final solution. At present, there are geological investigations of possible sites in progress in Slovakia. Mochovce repository is a factory for a final disposal of compacted low and intermediate level radioactive wastes coming from the Slovak NPPs. This is a near-surface facility of a construction similar to the one used for disposal of radioactive wastes in France, Spain, Japan, Czech Republic, U.S.A, etc. Quality of the design, construction and functioning of the Mochovce's repository was assessed by an international team of experts within a special IAEA programme (WATRP). Having familiarized with the final report of the IAEA mission, Nuclear Regulatory Authority of the Slovak Republic (NRA SR) issued its position early in 1995, in which NRA SR required additional adjustment of the repository itself. Based on the NRA SR's position, Mochovce NPP invited experts from a number of institutions in September 1995 to discuss the NRA SR's requirements. Following was recommended by the experts: (1) to perform a complementary engineering-geological investigation on the site, (2) to use geophysical methods to verify existence of geological faults. In the next part a radioactive wastes that were treated at radioactive waste treatment lines in 1995 are listed. In 1995, the Chief Inspector of NRA SR issued an instruction that radioactive waste department should start inspections of radioactive waste treatment right in hospitals, research institutes and industries. Therefore, a total of 14 such workplaces were incorporated into a plan of inspections in 1995

Preparation of Grinding Aid Using Waste Acid Residue from Plasticizer Plant

Science.gov (United States)

Li, Lingxiao; Feng, Yanchao; Liu, Manchao; Zhao, Fengqing

2017-09-01

The grinding aid for granulated blast-furnace slag were prepared from waste acid residue from plasticizer plant through neutralization, de-methanol and granulation process. In this process, sulfuric acid was transformed into gypsum which has much contribution for grinding effect by combined use with the glycerol and poly glycerin in the waste. Fly ash was used for granulation for the composite grinding aid. Methanol can be recycled in the process. The result showed that the suitable addition of grinding aid is 0.03 % of granulated blast-furnace slag (mass). In this case, the specific surface area is 14% higher than that of the blank. Compared with the common grinding aids, it has excellent performance and low cost.

Treatability study of absorbent polymer waste form for mixed waste treatment

International Nuclear Information System (INIS)

Herrmann, S. D.; Lehto, M. A.; Stewart, N. A.; Croft, A. D.; Kern, P. W.

2000-01-01

A treatability study was performed to develop and characterize an absorbent polymer waste form for application to low level (LLW) and mixed low level (MLLW) aqueous wastes at Argonne National Laboratory-West (ANL-W). In this study absorbent polymers proved effective at immobilizing aqueous liquid wastes in order to meet Land Disposal Restrictions for subsurface waste disposal. Treatment of aqueous waste with absorbent polymers provides an alternative to liquid waste solidification via high-shear mixing with clays and cements. Significant advantages of absorbent polymer use over clays and cements include ease of operations and waste volume minimization. Absorbent polymers do not require high-shear mixing as do clays and cements. Granulated absorbent polymer is poured into aqueous solutions and forms a gel which passes the paint filter test as a non-liquid. Pouring versus mixing of a solidification agent not only eliminates the need for a mixing station, but also lessens exposure to personnel and the potential for spread of contamination from treatment of radioactive wastes. Waste minimization is achieved as significantly less mass addition and volume increase is required of and results from absorbent polymer use than that of clays and cements. Operational ease and waste minimization translate into overall cost savings for LLW and MLLW treatment

Commercial mixed waste treatment and disposal

International Nuclear Information System (INIS)

Vance, J.K.

1994-01-01

At the South Clive, Utah, site, Envirocare of Utah, Inc., (Envirocare), currently operates a commercial low-activity, low-level radioactive waste facility, a mixed waste RCRA Part B storage and disposal facility, and an 11e.(2) disposal facility. Envirocare is also in the process of constructing a Mixed Waste Treatment Facility. As the nation's first and only commercial treatment and disposal facility for such waste, the information presented in this segment will provide insight into their current and prospective operations

A perspective of hazardous waste and mixed waste treatment technology at the Savannah River Site

International Nuclear Information System (INIS)

England, J.L.; Venkatesh, S.; Bailey, L.L.; Langton, C.A.; Hay, M.S.; Stevens, C.B.; Carroll, S.J.

1991-01-01

Treatment technologies for the preparation and treatment of heavy metal mixed wastes, contaminated soils, and mixed mercury wastes are being considered at the Savannah River Site (SRS), a DOE nuclear material processing facility operated by Westinghouse Savannah River Company (WSRC). The proposed treatment technologies to be included at the Hazardous Waste/Mixed Waste Treatment Building at SRS are based on the regulatory requirements, projected waste volumes, existing technology, cost effectiveness, and project schedule. Waste sorting and size reduction are the initial step in the treatment process. After sorting/size reduction the wastes would go to the next applicable treatment module. For solid heavy metal mixed wastes the proposed treatment is macroencapsulation using a thermoplastic polymer. This process reduces the leachability of hazardous constituents from the waste and allows easy verification of the coating integrity. Stabilization and solidification in a cement matrix will treat a wide variety of wastes (i.e. soils, decontamination water). Some pretreatments may be required (i.e. Ph adjustment) before stabilization. Other pretreatments such as soil washing can reduce the amount of waste to be stabilized. Radioactive contaminated mercury waste at the SRS comes in numerous forms (i.e. process equipment, soils, and lab waste) with the required treatment of high mercury wastes being roasting/retorting and recovery. Any unrecyclable radioactive contaminated elemental mercury would be amalgamated, utilizing a batch system, before disposal

Treatment of waste

International Nuclear Information System (INIS)

1981-01-01

A method of treating radioactive waste to substantially reduce the volume and which is especially useful in the treatment of material which includes radioactive halogens such as 131 I, is described. A fluidised bed incinerator and calciner are used to reduce all the liquid and combustible solid waste to anhydrous granular solids, all of which is carried by fluidizing gases into an off-gas system designed for their collection. (U.K.)

Dimethyl sulfoxide (DMSO) waste residues and municipal waste water odor by dimethyl sulfide (DMS): the north-east WPCP plant of Philadelphia.

Science.gov (United States)

Glindemann, Dietmar; Novak, John; Witherspoon, Jay

2006-01-01

This study shows for the first time that overlooked mg/L concentrations of industrial dimethyl sulfoxide (DMSO) waste residues in sewage can cause "rotten cabbage" odor problems bydimethyl sulfide (DMS) in conventional municipal wastewater treatment. In laboratory studies, incubation of activated sludge with 1-10 mg/L DMSO in bottles produced dimethyl sulfide (DMS) at concentrations that exceeded the odor threshold by approximately 4 orders of magnitude in the headspace gas. Aeration at a rate of 6 m3 air/m3 sludge resulted in emission of the DMS into the exhaust air in a manner analogous to that of an activated sludge aeration tank. A field study atthe NEWPCP sewage treatment plant in Philadelphia found DMSO levels intermittently peaking as high as 2400 mg/L in sewage near an industrial discharger. After 3 h, the DMSO concentration in the influent to the aeration tank rose from a baseline level of less than 0.01 mg/L to a level of 5.6 mg/L and the DMS concentration in the mixed liquor rose from less than 0.01 to 0.2 mg/L. Finding this link between the intermittent occurrence of DMSO residues in influent of the treatment plant and the odorant DMS in the aeration tank was the keyto understanding and eliminating the intermittent "canned corn" or "rotten cabbage" odor emissions from the aeration tank that had randomly plagued this plant and its city neighborhood for two decades. Sewage authorities should consider having wastewater samples analyzed for DMSO and DMS to check for this possible odor problem and to determine whether DMSO emission thresholds should be established to limit odor generation at sewage treatment plants.

Treatment of solid waste highly contaminated by alpha emitters: Low-temperature impact crushing, leaching and incineration

International Nuclear Information System (INIS)

Bertolotti, G.; Vigreux, B.; Caillol, A.; Koehly, G.

1987-01-01

Reprocessing plants, hot laboratories and fuel fabrication plants produce solid wastes containing residual amounts of plutonium and uranium in nitrate and oxide form at concentrations up to several tens of grams per m/sup 3/. Dismantling of nuclear facilities having handled these radioelements also generates large volumes of solid wastes highly contaminated with alpha emitters. It is desirable to process these alpha wastes to recover valuable fissile materials and/or permit surface storage. Solid waste treatment by low-temperature impact crushing and then leaching, after minimal sorting and classifying at the sites of production, meets the corresponding requirements for high volume reduction plus fissile material recovery or waste decontamination. Additional volume reduction of crushed wastes containing mainly combustible materials can be obtained by incineration. This is facilitated by the low fissile material content after low-temperature impact crushing and leaching. Sorted wastes can also be leached or incinerated directly after, in most cases, crushing by more conventional techniques

Treatment and disposal of radioactive wastes and countermeasures

International Nuclear Information System (INIS)

Nomura, Kiyoshi

1990-01-01

The treatment and disposal of radioactive wastes are one of important subjects, together with the development of dismantling techniques accompanying the decommissioning measures for nuclear power plants and the development of reprocessing techniques for nuclear fuel cycle. About 25 years have elapsed since the beginning of commercial nuclear power generation in 1966, and the time that the solution of the problems of waste treatment and disposal must be tackled on full scale has come. The features and the amount of generation of radioactive wastes, the way of thinking on the treatment and disposal, and the present status of the treatment and disposal are outlined. For securing the stable supply of energy and solving the environmental problem of the earth such as acid rain and warming, nuclear power generation accomplishes important roles. The objective of waste treatment is based on the way of thinking of 'as low as reasonably achievable (ALARA)'. The radioactive wastes are classified into alpha waste and beta-gamma waste. The present status of RI wastes, the techniques of treating radioactive wastes, the nuclide separation, extinction treatment and the disposal in strata of high level radioactive wastes and the disposal of low level wastes are reported. (K.I.)

Mixed and Low-Level Waste Treatment Facility project

International Nuclear Information System (INIS)

1992-04-01

Mixed and low-level wastes generated at the Idaho National Engineering Laboratory (INEL) are required to be managed according to applicable State and Federal regulations, and Department of Energy Orders that provide for the protection of human health and the environment. The Mixed and Low-Level Waste Treatment Facility Project was chartered in 1991, by the Department of Energy to provide treatment capability for these mixed and low-level waste streams. The first project task consisted of conducting engineering studies to identify the waste streams, their potential treatment strategies, and the requirements that would be imposed on the waste streams and the facilities used to process them. The engineering studies, initiated in July 1991, identified 37 mixed waste streams, and 55 low-level waste streams. This report documents the waste stream information and potential treatment strategies, as well as the regulatory requirements for the Department of Energy-owned treatment facility option. The total report comprises three volumes and two appendices. This report consists of Volume 1, which explains the overall program mission, the guiding assumptions for the engineering studies, and summarizes the waste stream and regulatory information, and Volume 2, the Waste Stream Technical Summary which, encompasses the studies conducted to identify the INEL's waste streams and their potential treatment strategies

The conversion of waste plastics/petroleum residue mixtures to transportation fuels

International Nuclear Information System (INIS)

Ali, M.F.; Siddiqui, M.N.

2005-01-01

Plastics have become the material of choice in the modern world and its applications in the industrial field are continually increasing. Presently the plastics are manufactured for various uses such as: consumer packaging, wires, pipes, containers, bottles, appliances, electrical/electronic parts, computers and automotive parts. Most of he post consumer, plastic products are discarded and end up as mixed plastic municipal waste. The disposal of his waste has become a major social concern. Mixed plastic waste (MPW) recycling is still very much in its infancy. Approximately 20 million tons of plastic waste is generated in the United States of America, while about 15 million tons is generated throughout the Europe. With existing recycle efforts, only 7% of the MPW are recycled to produce low-grade plastic products such as plastic sacks, pipes, plastic fencing, and garden furniture. The current plastic reclamation technology options are generally grouped into the following four types: (i) Primary: The processing of plastic for use comparable to the original application. (ii) Secondary: The processing of plastics waste into new products with a lower quality level. (iii) Tertiary: The chemical or thermal processing of plastic waste to their basic hydrocarbon feedstock. The resulting raw materials are then reprocessed into plastic material or other products of the oil refining process. (iv) Quaternary: The incineration of plastics waste to recover energy. This paper deals exclusively with tertiary recycling by pyrolysis and catalytic cracking of plastics waste alone and by coprocessing with petroleum residue or heavy oils to fuels and petrochemical feedstock for further processing in existing refinery and petrochemical units. (author)

Microwave calcination for plutonium immobilization and residue stabilization

Energy Technology Data Exchange (ETDEWEB)

Harris, M.J.; Rising, T.L.; Roushey, W.J.; Sprenger, G.S. [Kaiser-Hill Co., Golden, CO (United States)

1995-12-01

In the late 1980`s development was begun on a process using microwave energy to vitrify low level mixed waste sludge and transuranic mixed waste sludge generated in Building 374 at Rocky Flats. This process was shown to produce a dense, highly durable waste form. With the cessation of weapons production at Rocky Flats, the emphasis has changed from treatment of low level and TRU wastes to stabilizaiton of plutonium oxide and residues. This equipment is versatile and can be used as a heat source to calcine, react or vitrify many types of residues and oxides. It has natural economies in that it heats only the material to be treated, significantly reducing cycle times over conventional furnaces. It is inexpensive to operate in that most of the working components remain outside of any necessary contamination enclosure and therefore can easily be maintained. Limited testing has been successfully performed on cerium oxide (as a surrogate for plutonium oxide), surrogate electrorefining salts, surrogate residue sludge and residue ash. Future plans also include tests on ion exchange resins. In an attempt to further the usefullness of this technology, a mobile, self-contained microwave melting system is currently under development and expected to be operational at Rocky Flats Enviromental Technology Site by the 4th quarter of FY96.

Microwave calcination for plutonium immobilization and residue stabilization

International Nuclear Information System (INIS)

Harris, M.J.; Rising, T.L.; Roushey, W.J.; Sprenger, G.S.

1995-01-01

In the late 1980's development was begun on a process using microwave energy to vitrify low level mixed waste sludge and transuranic mixed waste sludge generated in Building 374 at Rocky Flats. This process was shown to produce a dense, highly durable waste form. With the cessation of weapons production at Rocky Flats, the emphasis has changed from treatment of low level and TRU wastes to stabilizaiton of plutonium oxide and residues. This equipment is versatile and can be used as a heat source to calcine, react or vitrify many types of residues and oxides. It has natural economies in that it heats only the material to be treated, significantly reducing cycle times over conventional furnaces. It is inexpensive to operate in that most of the working components remain outside of any necessary contamination enclosure and therefore can easily be maintained. Limited testing has been successfully performed on cerium oxide (as a surrogate for plutonium oxide), surrogate electrorefining salts, surrogate residue sludge and residue ash. Future plans also include tests on ion exchange resins. In an attempt to further the usefullness of this technology, a mobile, self-contained microwave melting system is currently under development and expected to be operational at Rocky Flats Enviromental Technology Site by the 4th quarter of FY96

Hospital waste sterilization: a technical and economic comparison between radiation and microwave treatments

International Nuclear Information System (INIS)

Tata, A.; Beone, F.

1995-01-01

Hospital waste (HW) disposal is becoming a problem of increasing importance in almost all industrially advanced countries. In Italy the yearly hospital waste production is about 250,000 tons and only 60,000 are treated by incineration at present time. As by a recent Italian law a meaningful percentage of HW (50 to 60%), corresponding to food residuals, plastic, paper, various organic materials, etc., could be landfilled as municipal refuses if preliminarily submitted to a suitable sterilization treatment. Under this perspective, sterilization/sanitation techniques represent now a technically and commercially viable alternative to HW thermal destruction that, besides more and more socially and politically less accepted. Electron Beam (EB) and Microwave (MW) treatments are two of the most interesting and emerging HW sterilization techniques, and, based on engineering real data, a technical and economic comparison is carried out, focusing vantages and limits of each process. (author)

Change of heavy metal speciation, mobility, bioavailability, and ecological risk during potassium ferrate treatment of waste-activated sludge.

Science.gov (United States)

Yu, Ming; Zhang, Jian; Tian, Yu

2018-05-01

The effects of potassium ferrate treatment on the heavy metal concentrations, speciation, mobility, bioavailability, and environmental risk in waste-activated sludge (WAS) at various dosages of potassium ferrate and different treatment times were investigated. Results showed that the total concentrations of all metals (except Cd) were decreased slightly after treatment and the order of metal concentrations in WAS and treated waste-activated sludge (TWAS) was Mg > Zn > Cu > Cr > Pb > Ni > Cd. Most heavy metals in WAS remained in TWAS after potassium ferrate treatment with metal residual rates over 67.8% in TWAS. The distribution of metal speciation in WAS was affected by potassium ferrate treatment. The bioavailability and the mobility of heavy metals (except Mg) in TWAS were mitigated, compared to those in WAS. Meanwhile, the environmental risk of heavy metals (except Pb and Cu) was alleviated after potassium ferrate treatment.

Fiscal 2000 achievement report. Development of technologies for waste treatment and recycling (Development of technologies for appropriate treatment of air bags); 2000 nendo haikibutsu recycle kanren gijutsu kaihatsu seika hokokusho. Air bag tekisei shori gijutsu no kaihatsu nado

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

A centralized treatment process respecting environmental protection and safety for unused air bags aboard disused automobiles is developed. In concrete terms, a heating facility owned by Daicel Chemical Industries, Ltd., is used, which includes an apparatus for examining exhaust gas dioxins and an exhaust gas treatment apparatus and, with this facility, studies are made for appropriately treating waste gas and waste water to be generated when air bag modules undergo centralized heating. Endeavors in fiscal 2000 center about (1) the development of waste gas treatment technologies, (2) development of waste water treatment technologies, (3) chemical analysis of waste water sludge, dusts and air bag residues, and (4) the study of appropriate treatment of non-azide air bag modules. As to the development of exhaust gas treatment technology, it was proved that the exhaust gas treatment system consisting of secondary incineration furnace, exhaust gas cooling tower and bag filter worked effectively. (NEDO)

Leaching of Antimony (Sb)from Municipal Solid Waste Incineration (MSWI) Residues

Energy Technology Data Exchange (ETDEWEB)

Herrmann, Inga

2004-07-01

The mobility of antimony (Sb) in municipal solid waste incineration (MSWI) residues often exceeds the limit values stipulated by the European Union. As an ash treatment by washing is conceivable, this work investigated the Sb release from Swedish bottom ash and fly ash when mixed with water. The leaching experiments revealed the factors significantly (a = 0.05) affecting Sb release from the ashes. The following factors were investigated: Liquid to solid ratio (L/S), time, pH, carbonation (treatment with CO{sub 2}), ultrasonics and temperature. The data were evaluated using multiple linear regression (MLR). The impact of the factors could be quantified. The maximum Sb release calculated was 13 mg/kg DM for bottom ash and 51 mg/kg DM for fly ash. The derived models explained the observed data well. Nevertheless, the calculated values were subject to a high uncertainty. For bottom ash, a lowering of the Sb total content of approximately 22% could be achieved. If this also involves a sufficient lowering of the Sb mobility to meet EU limit values could not yet be assessed. Chemical equilibrium calculations were performed to explain the empirical results. However, no solid phases controlling Sb release from the ashes could be identified.

Hanford Tanks 241-C-202 and 241-C-203 Residual Waste Contaminant Release Models and Supporting Data

Energy Technology Data Exchange (ETDEWEB)

Deutsch, William J.; Krupka, Kenneth M.; Lindberg, Michael J.; Cantrell, Kirk J.; Brown, Christopher F.; Mattigod, Shas V.; Schaef, Herbert T.; Arey, Bruce W.

2007-09-13

As directed by Congress, the U. S. Department of Energy (DOE) established the Office of River Protection in 1998 to manage DOE's largest, most complex environmental cleanup project – retrieval of radioactive waste from Hanford tanks for treatment and eventual disposal. Sixty percent by volume of the nation's high-level radioactive waste is stored at Hanford in aging deteriorating tanks. If not cleaned up, this waste is a threat to the Columbia River and the Pacific Northwest. CH2M Hill Hanford Group, Inc., is the Office of River Protection's prime contractor responsible for the storage, retrieval, and disposal of Hanford's tank waste. As part of this effort, CH2M HILL Hanford Group, Inc. contracted with Pacific Northwest National Laboratory (PNNL) to develop release models for key contaminants that are present in residual sludge remaining after closure of Hanford Tanks 241-C-203 (C-203) and 241-C-204 (C-204). The release models were developed from data generated by laboratory characterization and testing of samples from these two tanks. These release models are being developed to support the tank closure risk assessments performed by CH2M HILL Hanford Group, Inc., for DOE.

The potential of agro-industrial residues and municipal solid waste for production of biogas and electricity in Tanzania

Energy Technology Data Exchange (ETDEWEB)

Kivaisi, A K [Univ. of Dar es Salaam, Botany Dept., Applied Microbiology Unit (Tanzania, United Republic of)

1998-12-31

This paper gives an overview of the energy demands in Tanzania, and highlights the current serious shortage of electricity. Government strategy to alleviate the problem include exploitation of the country`s big natural gas reserves for power generation, and utilization of the renewable energies such as solar, wind and biogas. Important agro-industrial residues and municipal solid wastes with large potentials for anaerobic converstion into biogas and electricity have been identified and quantified. Tanzania is estimated to generate about 615,000 organic matter from coffee, sisal, sugar and cereal residues and households in main towns are estimated to generate about 600,000 tons of organic matter annually. Laboratory scale determinations of methane yields from the residues gave 400 m{sup 3} CH{sub 4}/ton VS of sisal pulp; 400 m{sup 3} CH{sub 4}/ton VS of sisal production wastewater; 400 m{sup 3} CH{sub 4}/ton VS of Robusta coffee solid waste, 350 m{sup 3} CH{sub 4}/ton VS of sugar processing wastewater; 250 m{sup 3} CH{sub 4}/ton VS of sugar filter mat, 450 m{sup 3} CH{sub 4}/ton VS maize bran and 300 m{sup 3} CH{sub 4}/ton VS of mixed household waste. Based on these results the estimated total annual potential electricity production from these residues is 1.4 million MW. The total oil substitution from these residues has been estimated at 0.35 million tonnes crude diesel oil per annum equivalent to 2% of the total energy consumption in Tanzania. Case studies onthe coffee and sisal processing factories indicate that exploitation of the residues for the production of electricity on site these factories is feasible. Utilization of agro-industrial residues and municipal waste for biogas production has enormous potential for reduction of environmental pollution. The potential substitution of fossil fuel with biogas represents an annual reduction in the net CO{sub 2} emission to the atmosphere of approximately 1.3 million tonnes. By treating the residues in controlled

The potential of agro-industrial residues and municipal solid waste for production of biogas and electricity in Tanzania

Energy Technology Data Exchange (ETDEWEB)

Kivaisi, A.K. [Univ. of Dar es Salaam, Botany Dept., Applied Microbiology Unit (Tanzania, United Republic of)

1997-12-31

This paper gives an overview of the energy demands in Tanzania, and highlights the current serious shortage of electricity. Government strategy to alleviate the problem include exploitation of the country`s big natural gas reserves for power generation, and utilization of the renewable energies such as solar, wind and biogas. Important agro-industrial residues and municipal solid wastes with large potentials for anaerobic converstion into biogas and electricity have been identified and quantified. Tanzania is estimated to generate about 615,000 organic matter from coffee, sisal, sugar and cereal residues and households in main towns are estimated to generate about 600,000 tons of organic matter annually. Laboratory scale determinations of methane yields from the residues gave 400 m{sup 3} CH{sub 4}/ton VS of sisal pulp; 400 m{sup 3} CH{sub 4}/ton VS of sisal production wastewater; 400 m{sup 3} CH{sub 4}/ton VS of Robusta coffee solid waste, 350 m{sup 3} CH{sub 4}/ton VS of sugar processing wastewater; 250 m{sup 3} CH{sub 4}/ton VS of sugar filter mat, 450 m{sup 3} CH{sub 4}/ton VS maize bran and 300 m{sup 3} CH{sub 4}/ton VS of mixed household waste. Based on these results the estimated total annual potential electricity production from these residues is 1.4 million MW. The total oil substitution from these residues has been estimated at 0.35 million tonnes crude diesel oil per annum equivalent to 2% of the total energy consumption in Tanzania. Case studies onthe coffee and sisal processing factories indicate that exploitation of the residues for the production of electricity on site these factories is feasible. Utilization of agro-industrial residues and municipal waste for biogas production has enormous potential for reduction of environmental pollution. The potential substitution of fossil fuel with biogas represents an annual reduction in the net CO{sub 2} emission to the atmosphere of approximately 1.3 million tonnes. By treating the residues in controlled

The potential of agro-industrial residues and municipal solid waste for production of biogas and electricity in Tanzania

International Nuclear Information System (INIS)

Kivaisi, A.K.

1997-01-01

This paper gives an overview of the energy demands in Tanzania, and highlights the current serious shortage of electricity. Government strategy to alleviate the problem include exploitation of the country's big natural gas reserves for power generation, and utilization of the renewable energies such as solar, wind and biogas. Important agro-industrial residues and municipal solid wastes with large potentials for anaerobic converstion into biogas and electricity have been identified and quantified. Tanzania is estimated to generate about 615,000 organic matter from coffee, sisal, sugar and cereal residues and households in main towns are estimated to generate about 600,000 tons of organic matter annually. Laboratory scale determinations of methane yields from the residues gave 400 m 3 CH 4 /ton VS of sisal pulp; 400 m 3 CH 4 /ton VS of sisal production wastewater; 400 m 3 CH 4 /ton VS of Robusta coffee solid waste, 350 m 3 CH 4 /ton VS of sugar processing wastewater; 250 m 3 CH 4 /ton VS of sugar filter mat, 450 m 3 CH 4 /ton VS maize bran and 300 m 3 CH 4 /ton VS of mixed household waste. Based on these results the estimated total annual potential electricity production from these residues is 1.4 million MW. The total oil substitution from these residues has been estimated at 0.35 million tonnes crude diesel oil per annum equivalent to 2% of the total energy consumption in Tanzania. Case studies onthe coffee and sisal processing factories indicate that exploitation of the residues for the production of electricity on site these factories is feasible. Utilization of agro-industrial residues and municipal waste for biogas production has enormous potential for reduction of environmental pollution. The potential substitution of fossil fuel with biogas represents an annual reduction in the net CO 2 emission to the atmosphere of approximately 1.3 million tonnes. By treating the residues in controlled anaerobic systems it is possible to reduce the methane emission by

Methods of conditioning waste fuel decladding hulls and dissolver residues

International Nuclear Information System (INIS)

De Regge, P.; Loida, A.; Schmidt-Hansberg, T.; Sombret, C.

1985-01-01

Several methods for conditioning spent fuel decladding hulls or dissolver residues have been considered in various countries of the European Community. Five of these methods used embedding technique with or without prior compaction: they are based on incorporation in metallic alloys, glass, ceramics, cements and metals or graphite compounds. A sixth one consists in melting the decladding materials. The corresponding research programmes have been pursued to varying states of progress with regard to demonstrating their feasibility on an industrial scale and the use of genuine wastes in bench scale experiments. The properties of the conditioned wastes have been investigated. Special attention has been paid to the corrosion resistance to various aqueous media as tap water, brine or clayey water. Although no categorical conclusion can be drawn from the initial results, the available findings provide a basis for assessing the different processes

Treatment of alpha bearing wastes

International Nuclear Information System (INIS)

1988-01-01

This report deals with the current state of the art of alpha waste treatment, which is an integral part of the overall nuclear waste management system. The International Atomic Energy Agency (IAEA) defines alpha bearing waste as 'waste containing one or more alpha emitting radionuclides, usually actinides, in quantities above acceptable limits'. The limits are established by national regulatory bodies. The limits above which wastes are considered as alpha contaminated refer to the concentrations of alpha emitters that need special consideration for occupational exposures and/or potential safety, health, or environmental impact during one or more steps from generation through disposal. Owing to the widespread use of waste segregation by source - that is, based upon the 'suspect origin' of the material - significant volumes of waste are being handled as alpha contaminated which, in fact, do not require such consideration by reason of risk or environmental concern. The quantification of de minimis concepts by national regulatory bodies could largely contribute to the safe reduction of waste volumes and associated costs. Other factors which could significantly contribute to the reduction of alpha waste arisings are an increased application of assaying and sorting, instrumentation and the use of feedback mechanisms to control or modify the processes which generate these wastes. Alpha bearing wastes are generated during fabrication and reprocessing of nuclear fuels, decommissioning of alpha contaminated facilities, and other activities. Most alpha wastes are contact handled, but a small portion may require shielding or remote handling because of high levels of neutron (n), beta (β), or gamma (γ) emissions associated with the waste material. This report describes the sources and characteristics of alpha wastes and strategies for alpha waste management. General descriptions of treatment processes for solid and liquid alpha wastes are included. 71 refs, 14 figs, 9 tabs

Cyanide wastes treatment by bioremediation

International Nuclear Information System (INIS)

Deloya Martinez, Alma

2012-01-01

The results of the development of an autochthonous consortium of degrader microorganisms of the cyanide for the application in the biological treatment of the dangerous wastes of cyanide, were presented. The autochthonous microorganisms obtained were lyophilized in different protective environments, such as gelatin and lactose broth at different temperatures (-35, -45, -55 and -65). A pretreatment method in slurry was applied for the preliminary treatment of the cyanide wastes: for the preliminary leaching of the waste, with periods between 3 and 5 days and a posterior treatment, by aerated lagoons, applying the consortium of lyophilized microorganisms. Eight different lyophilized were obtained in different temperature conditions and with two lyophilization protective media that have presented excellent recovery at six months of lyophilization. The consortium of lyophilized microorganisms has presented 70 to 80 percent of viability, with cyanide removal percentages higher than 95% and it can be conserved active for a prolonged time (for years). The lyophilized microorganisms can be applied in the biodegradation of the cyanide wastes from the gold mines or any other cyanide waste such as metal electroplanting baths, as well as from jewelry manufacturing. (author) [es

Treatment of liquid radioactive waste: Precipitation

International Nuclear Information System (INIS)

Gompper, K.

1982-01-01

After introductory remarks about waste types to be treated, specific treatment methods are discussed and examples are given for treatment processes carried out with different types of liquid wastes from nuclear power plants, research centers and fuel reprocessing plants. (RW)

Waste management and treatment or disguised disposal?

International Nuclear Information System (INIS)

Drum, D.A.; Lauber, J.

1992-01-01

A number of political action groups, environmental groups, and waste management industries have purposely used medical waste data and municipal solid waste test results to mislead public officials and communities. Waste management schemes and waste treatment technologies must be measured and compared by the same test criteria. For example, anti-incineration groups often use the toxic dioxin/furan data and/or toxic metal arguments to oppose waste-to-energy incineration technologies. Comparable test data on waste management techniques such as waste composting, autoclaving, and landfilling are either nonexistent or often inappropriately applied. Integrated waste management systems require technologically accurate and complete data, environmentally-appropriate designed systems, and fiscal responsibility. The primary emphasis of waste management and treatment practices must be directed toward minimization, reuse, destruction, and detoxification of municipal solid wastes and medical wastes. The issues and alternatives will be examined

Hazardous waste inventory, characteristics, generation, and facility assessment for treatment, storage, and disposal alternatives considered in the U.S. Department of Energy Waste Management Programmatic Environmental Impact Statement

International Nuclear Information System (INIS)

Lazaro, M.A.; Antonopoulos, A.A.; Esposito, M.P.; Policastro, A.J.

1996-12-01

This report focuses on the generation of hazardous waste (HW) and the treatment of HW being generated by routine US Department of Energy (DOE) facility operations. The wastes to be considered are managed by the DOE Waste Management (WM) Division (WM HW). The waste streams are to be sent to WM operations throughout the DOE complex under four management alternatives: No Action, Decentralization, Regionalized 1, and Regionalized 2. On-site and off-site capabilities for treatment are examined for each alternative. This report (1) summarizes the HW inventories and generated amounts resulting from WM activities, focusing on the largest DOE HW generators; (2) presents estimates of the annual amounts shipped off-site, as well as the amounts treated by various treatment technology groups; (3) describes the existing and planned treatment and storage capabilities of the largest HW-generating DOE installations, as well as the use of commercial treatment facilities by DOE sites; (4) presents applicable technologies (destruction of organics, deactivation/neutralization of waste, removal/recovery of organics, and aqueous liquid treatment); and (5) describes the four alternatives for consideration for future HW management, and for each alternative provides the HW loads and the approach used to estimate the source term for routine treatment operations. In addition, potential air emissions, liquid effluents, and solid residuals associated with each alternative are presented. This report is supplemented with an addendum that includes detailed information related to HW inventory, characteristics, generation, and facility assessment for the treatment alternatives. The addendum also presents source terms, emission rates, and throughput totals by alternative and treatment installation

Treatment of radioactive wastes containing plutonium

International Nuclear Information System (INIS)

Orlando, O.S.; Aparicio, G.; Greco, L.; Orosco, E.H.; Cassaniti, P.; Salguero, D.; Toubes, B.; Perez, A.E.; Menghini, J.E.; Esteban, A.; Adelfang, P.

1987-01-01

The radioactive wastes generated in the process of manufacture and control of experimental fuel rods of mixed oxides, (U,Pu)O 2 , require an specific treatment due to the plutonium content. The composition of liquid wastes, mostly arising from chemical checks, is variable. The salt content, the acidity, and the plutonium and uranium content are different, which makes necessary a chemical treatment before the inclusion in concrete. The solid waste, such as neoprene gloves, PVC sleeves, filter paper, disposable or broken laboratory material, etc. are also included in concrete. In this report the methods used to dispose of wastes at Alpha Facility are described. With regard to the liquid wastes, the glove box built to process them is detailed, as well as the applied chemical treatment, including neutralization, filtration and later solidification. As for the solid wastes, it is described the cementation method consisting in introducing them into an expanded metal matrix, of the basket type, that contains as a concentric drum of 200 liter capacity which is smaller than the matrix, and the filling with wet cement mortar. (Author)

Advanced pyrochemical technologies for minimizing nuclear waste

International Nuclear Information System (INIS)

Bronson, M.C.; Dodson, K.E.; Riley, D.C.

1994-01-01

The Department of Energy (DOE) is seeking to reduce the size of the current nuclear weapons complex and consequently minimize operating costs. To meet this DOE objective, the national laboratories have been asked to develop advanced technologies that take uranium and plutonium, from retired weapons and prepare it for new weapons, long-term storage, and/or final disposition. Current pyrochemical processes generate residue salts and ceramic wastes that require aqueous processing to remove and recover the actinides. However, the aqueous treatment of these residues generates an estimated 100 liters of acidic transuranic (TRU) waste per kilogram of plutonium in the residue. Lawrence Livermore National Laboratory (LLNL) is developing pyrochemical techniques to eliminate, minimize, or more efficiently treat these residue streams. This paper will present technologies being developed at LLNL on advanced materials for actinide containment, reactors that minimize residues, and pyrochemical processes that remove actinides from waste salts

Surgical treatment for residual or recurrent strabismus

Directory of Open Access Journals (Sweden)

Tao Wang

2014-12-01

Full Text Available Although the surgical treatment is a relatively effective and predictable method for correcting residual or recurrent strabismus, such as posterior fixation sutures, medial rectus marginal myotomy, unilateral or bilateral rectus re-recession and resection, unilateral lateral rectus recession and adjustable suture, no standard protocol is established for the surgical style. Different surgical approaches have been recommended for correcting residual or recurrent strabismus. The choice of the surgical procedure depends on the former operation pattern and the surgical dosages applied on the patients, residual or recurrent angle of deviation and the operator''s preference and experience. This review attempts to outline recent publications and current opinion in the management of residual or recurrent esotropia and exotropia.

Wet oxidative degradation of cellulosic wastes 5- chemical and thermal properties of the final waste forms

International Nuclear Information System (INIS)

Eskander, S.B.; Saleh, H.M.

2002-01-01

In this study, the residual solution arising from the wet oxidative degradation of solid organic cellulosic materials, as one of the component of radioactive solid wastes, using hydrogen peroxide as oxidant. Were incorporated into ordinary Portland cement matrix. Leaching as well as thermal characterizations of the final solidified waste forms were evaluated to meet the final disposal requirements. Factors, such as the amount of the residual solution incorporated, types of leachant. Release of different radionuclides and freezing-thaw treatment, that may affect the leaching characterization. Were studied systematically from the data obtained, it was found that the final solid waste from containing 35% residual solution in tap water is higher than that in ground water or sea water. Based on the data obtained from thermal analysis, it could be concluded that incorporating the residual solution form the wet oxidative degradation of cellulosic materials has no negative effect on the hydration of cement materials and consequently on the thermal stability of the final solid waste from during the disposal process

Upgrading pyrolytic residue from waste tires to commercial carbon black.

Science.gov (United States)

Zhang, Xue; Li, Hengxiang; Cao, Qing; Jin, Li'e; Wang, Fumeng

2018-05-01

The managing and recycling of waste tires has become a worldwide environmental challenge. Among the different disposal methods for waste tires, pyrolysis is regarded as a promising route. How to effectively enhance the added value of pyrolytic residue (PR) from waste tires is a matter of great concern. In this study, the PRs were treated with hydrochloric and hydrofluoric acids in turn under ultrasonic waves. The removal efficiency for the ash and sulfur was investigated. The pyrolytic carbon black (PCB) obtained after treating PR with acids was analyzed by X-ray fluorescence spectrophotometry, Fourier transform infrared spectrometry, X-ray diffractometry, laser Raman spectrometry, scanning electron microscopy, thermogravimetric (TG) analysis, and physisorption apparatus. The properties of PCB were compared with those of commercial carbon black (CCB) N326 and N339. Results showed PRs from waste tires were mainly composed of carbon, sulfur, and ash. The carbon in PCB was mainly from the CCB added during tire manufacture rather than from the pyrolysis of pure rubbers. The removal percentages for the ash and sulfur of PR are 98.33% (from 13.98 wt % down to 0.24 wt %) and 70.16% (from 1.81 wt % down to 0.54 wt %), respectively, in the entire process. The ash was mainly composed of metal oxides, sulfides, and silica. The surface properties, porosity, and morphology of the PCB were all close to those of N326. Therefore, PCB will be a potential alternative of N326 and reused in tire manufacture. This route successfully upgrades PR from waste tires to the high value-added CCB and greatly increases the overall efficiency of the waste tire pyrolysis industry.

Mixed and low-level waste treatment facility project. Volume 3, Waste treatment technologies (Draft)

Energy Technology Data Exchange (ETDEWEB)

1992-04-01

The technology information provided in this report is only the first step toward the identification and selection of process systems that may be recommended for a proposed mixed and low-level waste treatment facility. More specific information on each technology will be required to conduct the system and equipment tradeoff studies that will follow these preengineering studies. For example, capacity, maintainability, reliability, cost, applicability to specific waste streams, and technology availability must be further defined. This report does not currently contain all needed information; however, all major technologies considered to be potentially applicable to the treatment of mixed and low-level waste are identified and described herein. Future reports will seek to improve the depth of information on technologies.

Integrated treatment process of hazardous and mixed wastes

International Nuclear Information System (INIS)

Shibuya, M.; Suzuki, K.; Fujimura, Y.; Nakashima, T.; Moriya, Y.

1993-01-01

An integrated waste treatment system was studied based on technologies developed for the treatment of liquid radioactive, organic, and aqueous wastes containing hazardous materials and soils contaminated with heavy metals. The system consists of submerged incineration, metal ion fixing and stabilization, and soil washing treatments. Introduction of this system allows for the simultaneous processing of toxic waste and contaminated soils. Hazardous organic wastes can be decomposed into harmless gases, and aqueous wastes can be converted into a dischargeable effluent. The contaminated soil is backfilled after the removal of toxic materials. Experimental data show that the integration system is practical for complicated toxic wastes

Maximising municipal solid waste--legume trimming residue mixture degradation in composting by control parameters optimization.

Science.gov (United States)

Cabeza, I O; López, R; Ruiz-Montoya, M; Díaz, M J

2013-10-15

Composting is one of the most successful biological processes for the treatment of the residues enriched in putrescible materials. The optimization of parameters which have an influence on the stability of the products is necessary in order to maximize recycling and recovery of waste components. The influence of the composting process parameters (aeration, moisture, C/N ratio, and time) on the stability parameters (organic matter, N-losses, chemical oxygen demand, nitrate, biodegradability coefficient) of the compost was studied. The composting experiment was carried out using Municipal Solid Waste (MSW) and Legume Trimming Residues (LTR) in 200 L isolated acrylic barrels following a Box-Behnken central composite experimental design. Second-order polynomial models were found for each of the studied compost stability parameter, which accurately described the relationship between the parameters. The differences among the experimental values and those estimated by using the equations never exceeded 10% of the former. Results of the modelling showed that excluding the time, the C/N ratio is the strongest variable influencing almost all the stability parameters studied in this case, with the exception of N-losses which is strongly dependent on moisture. Moreover, an optimized ratio MSW/LTR of 1/1 (w/w), moisture content in the range of 40-55% and moderate to low aeration rate (0.05-0.175 Lair kg(-)(1) min(-1)) is recommended to maximise degradation and to obtain a stable product during co-composting of MSW and LTR. Copyright © 2013 Elsevier Ltd. All rights reserved.

Study of immobilization of waste from treatment of acid waters of a uranium mining facility

International Nuclear Information System (INIS)

Goda, R.T.; Oliveira, A.P. de; Silva, N.C. da; Villegas, R.A.S.; Ferreira, A.M.

2017-01-01

This study aimed to produce scientific and technical knowledge aiming at the development of techniques to immobilize the waste generated in the treatment of acid waters in the UTM-INB Caldas uranium mining and processing facility using Portland cement. This residue (calcium diuranate - DUCA) contains uranium compounds and metal hydroxides in a matrix of calcium sulfate. It is observed that this material, in contact with the lake of acid waters of the mine's own pit, undergoes resolubilization and, therefore, changes the quality of the acidic water contained therein, changing the treatment parameters. For the study of immobilization of this residue, the mass of water contained in both the residue deposited in the pit of the mine and in the pulp resulting from the treatment of the acid waters was determined. In addition, different DUCA / CEMENT / WATER ratios were used for immobilization and subsequent mechanical strength and leaching tests. The results showed that in the immobilized samples with 50% cement mass condition, no uranium was detected in the leaching tests, and the mechanical strength at compression was 9.4 MPa, which indicates that more studies are needed, but indicate a good capacity to immobilize uranium in cement

Manufacturing of concrete with residues from iron ore exploitation using the technology of radioactive waste cementation

Energy Technology Data Exchange (ETDEWEB)

Versieux, Juniara L.; Lameiras, Fernando S.; Tello, Cledola Cassia Oliveira de, E-mail: juniarani@gmail.com, E-mail: fsl@cdtn.br, E-mail: tellocc@cdtn.br [Centro de Desenvolvimento da Tecnologia Nucelar (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

2015-07-01

Radioactive wastes from various segments of economy are immobilized by cementation, because of availability and widespread use in civil construction of cement. New cementitious materials are developed in CDTN using mining residues based on cementing techniques of radioactive wastes. Special procedures were developed to obtain concrete with the use of super plasticizers in which natural sand was totally replaced by mining residues. The motivation for this research is the exploration of banded iron formations (BIF) as iron ore in 'Quadrilatero Ferrifero' of Minas Gerais, where huge amounts of residues are generated with great concern about the environmental sustainability and safety of dams for residue storage. The exploitation of river sand causes many negative impacts, which leads to interest in its replacement by another raw material in mortar and concrete manufacturing. The use of BIF mining residues were studied for manufacturing of concrete pavers to contribute to reducing the impact caused by extraction of natural sand and use of mining residues. Previously developed procedures with total replacement of natural sand for mining residues were modified, including use of gravel to obtain pavers with improved properties. Four different mixtures were tested, in which the proportion of gravel and super plasticizer was varied. Monitored properties of pavers, among others, were compression resistance, water absorption, and void volume. With addition of gravel, the pavers had higher void index than those made only with mortar, and higher resistance to compression after 28 days of curing (an average of 18MPa of those made with mortar to 24MPa of those made with concrete). (author)

Manufacturing of concrete with residues from iron ore exploitation using the technology of radioactive waste cementation

International Nuclear Information System (INIS)

Versieux, Juniara L.; Lameiras, Fernando S.; Tello, Cledola Cassia Oliveira de

2015-01-01

Radioactive wastes from various segments of economy are immobilized by cementation, because of availability and widespread use in civil construction of cement. New cementitious materials are developed in CDTN using mining residues based on cementing techniques of radioactive wastes. Special procedures were developed to obtain concrete with the use of super plasticizers in which natural sand was totally replaced by mining residues. The motivation for this research is the exploration of banded iron formations (BIF) as iron ore in 'Quadrilatero Ferrifero' of Minas Gerais, where huge amounts of residues are generated with great concern about the environmental sustainability and safety of dams for residue storage. The exploitation of river sand causes many negative impacts, which leads to interest in its replacement by another raw material in mortar and concrete manufacturing. The use of BIF mining residues were studied for manufacturing of concrete pavers to contribute to reducing the impact caused by extraction of natural sand and use of mining residues. Previously developed procedures with total replacement of natural sand for mining residues were modified, including use of gravel to obtain pavers with improved properties. Four different mixtures were tested, in which the proportion of gravel and super plasticizer was varied. Monitored properties of pavers, among others, were compression resistance, water absorption, and void volume. With addition of gravel, the pavers had higher void index than those made only with mortar, and higher resistance to compression after 28 days of curing (an average of 18MPa of those made with mortar to 24MPa of those made with concrete). (author)

Challenges when Performing Economic Optimization of Waste Treatment

DEFF Research Database (Denmark)

Juul, Nina; Münster, Marie; Ravn, Hans

2011-01-01

New investments in waste treatment facilities are needed due to a number of factors including continuously increasing waste amounts, political demands for efficient utilization of the waste resources in terms of recycling or energy production, and decommissioning of existing waste treatment...... facilities due to age and stricter environmental regulation. Optimization models can assist in ensuring that these investment strategies will be economically feasible. Various economic optimization models for waste treatment have been developed which focus on different parameters. Models focusing...... in multi criteria analysis have been developed. A thorough updated review of the existing models is presented and the main challenges and the crucial parameters to take into account when assessing the economic performance of waste treatment alternatives are identified. The review article will assist both...

Long chain fatty acids (LCFA) evolution for inhibition forecasting during anaerobic treatment of lipid-rich wastes: Case of milk-fed veal slaughterhouse waste.

Science.gov (United States)

Rodríguez-Méndez, R; Le Bihan, Y; Béline, F; Lessard, P

2017-09-01

A detailed study of a solid slaughterhouse waste (SHW) anaerobic treatment is presented. The waste used in this study is rich in lipids and proteins residue. Long chain fatty acids (LCFA), coming from the hydrolysis of lipids were inhibitory to anaerobic processes at different degrees. Acetogenesis and methanogenesis processes were mainly affected by inhibition whereas disintegration and hydrolysis processes did not seem to be affected by high LCFA concentrations. Nevertheless, because of the high energy content, this kind of waste is very suitable for anaerobic digestion but strict control of operating conditions is required to prevent inhibition. For that, two inhibition indicators were identified in this study. Those two indicators, LCFA dynamics and LCFA/VS biomass ratio proved to be useful to predict and to estimate the process inhibition degree. Copyright © 2017 Elsevier Ltd. All rights reserved.

Sodium-Bearing Waste Treatment Alternatives Implementation Study

Energy Technology Data Exchange (ETDEWEB)

Charles M. Barnes; James B. Bosley; Clifford W. Olsen

2004-07-01

The purpose of this document is to discuss issues related to the implementation of each of the five down-selected INEEL/INTEC radioactive liquid waste (sodium-bearing waste - SBW) treatment alternatives and summarize information in three main areas of concern: process/technical, environmental permitting, and schedule. Major implementation options for each treatment alternative are also identified and briefly discussed. This report may touch upon, but purposely does not address in detail, issues that are programmatic in nature. Examples of these include how the SBW will be classified with respect to the Nuclear Waste Policy Act (NWPA), status of Waste Isolation Pilot Plant (WIPP) permits and waste storage availability, available funding for implementation, stakeholder issues, and State of Idaho Settlement Agreement milestones. It is assumed in this report that the SBW would be classified as a transuranic (TRU) waste suitable for disposal at WIPP, located in New Mexico, after appropriate treatment to meet transportation requirements and waste acceptance criteria (WAC).

Saponification pretreatment and solids recirculation as a new anaerobic process for the treatment of slaughterhouse waste.

Science.gov (United States)

Affes, R; Palatsi, J; Flotats, X; Carrère, H; Steyer, J P; Battimelli, A

2013-03-01

Different configurations of anaerobic process, adapted to the treatment of solid slaughterhouse fatty waste, were proposed and evaluated in this study. The tested configurations are based on the combination of anaerobic digestion with/without waste saponification pretreatment (70 °C during 60 min) and with/without recirculation of the digestate solid fraction (ratio=20% w/w). After an acclimation period of substrate pulses-feeding cycles, the reactors were operated in a semi-continuous feeding mode, increasing organic loading rates along experimental time. The degradation of the raw substrate was shown to be the bottleneck of the whole process, obtaining the best performance and process yields in the reactor equipped with waste pretreatment and solids recirculation. Saponification promoted the emulsification and bioavailability of solid fatty residues, while recirculation of solids minimized the substrate/biomass wash-out and induced microbial adaptation to the treatment of fatty substrates. Copyright © 2013 Elsevier Ltd. All rights reserved.

Evaluation of residual activity of solid waste generated in nuclear medicine services of Porto Alegre - Brazil

International Nuclear Information System (INIS)

Xavier, Ana M.; Alabarse, Frederico Gil; Magalhaes, Maisa Haiidamus; Guerrero, Jesus Salvador Perez

2008-01-01

An experimental programme to estimate, with a better degree of accuracy, the activity that remains adsorbed in flasks and syringes used in Nuclear Medicine Services for the administration of radionuclides to patients submitted to diagnostic or therapy was conducted under the coordination of the Radioactive Waste Division of the Brazilian Nuclear Energy Commission. The adopted recommendation in Brazil to allow an expedite solid waste management in nuclear medicine facilities, up to the present, is to consider that 2% of the initial activity remains adsorbed in the solid waste, which easily allows the calculation of the storage time to achieve regulatory clearance levels by decay. This research evaluates 17 different kinds of radio pharmaceuticals and three radioisotopes: 99m Tc, 67 Ga and 201 Tl. Results obtained by means of a weighting method to estimate the residual mass in flasks show that the ratio of the mass of the liquid that remains in the solid waste to the mass of the empty flask is constant. This suggests that the residual activity depends on the initial activity concentration of radiopharmaceutical contained in each flask, as assumed by the regulatory body. Additionally, results obtained by determining the remaining activity in flasks, shortly after the injection of its radionuclides contents in patients, indicate that an average value for the residual activity of the order of 10% of the initial activity contained in the flasks or syringes can be adopted instead of the previously assumed 2%. It is suggested that the more conservative average value obtained in the present work for the activity that remains in flasks and syringes, that is, 10% of the initial activity, could be adopted to determine the decay storage time before the release of solid waste in the urban conventional land fill disposal system. (author)

Organic waste treatment with organically modified clays

International Nuclear Information System (INIS)

Evans, J.C.; Pancoski, S.E.; Alther, G.

1989-01-01

The use of organically modified clays in hazardous waste management applications offers a significant new and untapped potential. These clays may be used in the stabilization of organic wastes and organically contaminated soils, for waste water treatment, for oil spill control, for liner systems beneath fuel oil storage tanks, and as a component within liner systems of hazardous waste storage treatment and disposal facilities. Organically modified clays (organophilic clays) may be employed in each of these systems to adsorb organic waste constituents, enhancing the performance of the applications

Treatment of supermarket vegetable wastes to be used as alternative substrates in bioprocesses.

Science.gov (United States)

Díaz, Ana Isabel; Laca, Amanda; Laca, Adriana; Díaz, Mario

2017-09-01

Fruits and vegetables have the highest wastage rates at retail and consumer levels. These wastes have promising potential for being used as substrates in bioprocesses. However, an effective hydrolysis of carbohydrates that form these residues has to be developed before the biotransformation. In this work, vegetable wastes from supermarket (tomatoes, green peppers and potatoes) have been separately treated by acid, thermal and enzymatic hydrolysis processes in order to maximise the concentration of fermentable sugars in the final broth. For all substrates, thermal and enzymatic processes have shown to be the most effective. A new combined hydrolysis procedure including these both treatments was also assayed and the enzymatic step was successfully modelled. With this combined hydrolysis, the percentage of reducing sugars extracted was increased, in comparison with the amount extracted from non-hydrolysed samples, approximately by 30% in the case of tomato and green peeper wastes. For potato wastes this percentage increased from values lower than 1% to 77%. In addition, very low values of fermentation inhibitors were found in the final broth. Copyright © 2017. Published by Elsevier Ltd.

Regional waste treatment with monolith disposal for low-level radioactive waste

International Nuclear Information System (INIS)

Forsberg, C.W.

1983-01-01

An alternative system is proposed for the disposal of low-level radioactive waste. This system, called REgional Treatment with MOnolith Disposal (RETMOD), is based on integrating three commercial technologies: automated package warehousing, whole-barrel rotary kiln incineration, and cement-based grouts for radioactive waste disposal. In the simplified flowsheet, all the sludges, liquids, resins, and combustible wastes are transported to regional facilities where they are incinerated. The ash is then mixed with special cement-based grouts, and the resulting mixture is poured into trenches to form large waste-cement monoliths. Wastes that do not require treatment, such as damaged and discarded equipment, are prepositioned in the trenches with the waste-cement mixture poured on top. The RETMOD system may provide higher safety margins by conversion of wastes into a solidified low-leach form, creation of low-surface area waste-cement monoliths, and centralization of waste processing into a few specialized facilities. Institutional problems would be simplified by placing total responsibility for safe disposal on the disposal site operator. Lower costs may be realized through reduced handling costs, the economics of scale, simplified operations, and less restrictive waste packaging requirements

Valorisation of fish by-products against waste management treatments--Comparison of environmental impacts.

Science.gov (United States)

Lopes, Carla; Antelo, Luis T; Franco-Uría, Amaya; Alonso, Antonio A; Pérez-Martín, Ricardo

2015-12-01

Reuse and valorisation of fish by-products is a key process for marine resources conservation. Usually, fishmeal and oil processing factories collect the by-products generated by fishing port and industry processing activities, producing an economical benefit to both parts. In the same way, different added-value products can be recovered by the valorisation industries whereas fishing companies save the costs associated with the management of those wastes. However, it is important to estimate the advantages of valorisation processes not only in terms of economic income, but also considering the environmental impacts. This would help to know if the valorisation of a residue provokes higher impact than other waste management options, which means that its advantages are probably not enough for guarantying a sustainable waste reuse. To that purpose, there are several methodologies to evaluate the environmental impacts of processes, including those of waste management, providing different indicators which give information on relevant environmental aspects. In the current study, a comparative environmental assessment between a valorisation process (fishmeal and oil production) and different waste management scenarios (composting, incineration and landfilling) was developed. This comparison is a necessary step for the development and industrial implementation of these processes as the best alternative treatment for fish by-products. The obtained results showed that both valorisation process and waste management treatments presented similar impacts. However, a significant benefit can be achieved through valorisation of fish by-products. Additionally, the implications of the possible presence of pollutants were discussed. Copyright © 2015 Elsevier Ltd. All rights reserved.

Thermal and catalytic decomposition behavior of PVC mixed plastic waste with petroleum residue

Energy Technology Data Exchange (ETDEWEB)

Ali, Mohammad Farhat; Siddiqui, Mohammad Nahid [Department of Chemistry, King Fahd University of Petroleum and Minerals, Dhahran 31261 (Saudi Arabia)

2005-08-15

The pyrolysis and hydropyrolysis of PVC mixed plastic waste alone and with petroleum residue was carried out at 150 and 350{sup o}C under N{sub 2} gas and at 430{sup o}C under 6.5MPa H{sub 2} gas pressure. The behavior of plastic waste during thermal and catalytic decomposition has also been studied in single- and two-stage reaction processes. In the individual pyrolysis process, both the petroleum residue and polystyrene (PS) undergo more than 90% conversion to liquid and gaseous products, whereas low-density polyethylene (LDPE) and high-density polyethylene (HDPE) yielded lower conversions products, and polypropylene (PP) and polyvinyl chloride (PVC) afforded somewhere a moderate to high conversion products. In a single-stage pyrolysis reaction, PVC was processed with petroleum residue at 150 and 430{sup o}C, under N{sub 2} gas for 1h at each temperature in a glass reactor. The model PVC and waste PVC showed slight variations in the products distribution obtained from the glass reactor. In two-stage process, model PVC, vacuum gas oil (VGO) and a number of different catalysts were used in a stainless steel autoclave micro tubular reactor at 350{sup o}C under the stream of N{sub 2} gas for 1h and at 430{sup o}C under 950psi (6.5MPa) H{sub 2} pressure for the duration of 2h. Significantly, different products distributions were obtained. Among the catalysts used, fluid catalytic cracking (FCC) and hydrocracking catalysts (HC-1) were most effective in producing liquid fuel (hexane soluble) materials. The study shows that the catalytic coprocessing of PVC with VGO is a feasible process by which PVC and VGO materials can be converted into transportation fuels.

17. Meeting municipal waste Magdeburg. Residual waste - recycling - resource; 17. Tagung Siedlungsabfallwirtschaft Magdeburg. Restabfall - Recycling - Ressource

Energy Technology Data Exchange (ETDEWEB)

Haase, Hartwig (ed.)

2012-11-01

Within the 17th meeting Waste Management at Residential Areas from 12th o 13th September, 2012 in Magdeburg (Federal Republic of Germany), the following lectures were held: (1) Opening Session - Waste management in Saxony-Anhalt (O. Aeikens); (2) World with future - the eco-social perspective (F.J. Radermacher); (3) Global commodity markets - rare earths and their recycling (I. Fahimi); (4) The further development of nearhousehold capture of recyclable materials (J. Seitel); (5) On the future of the disposal management (J. Balg); (6) Options for action for the future of the municipal waste management (A. Gosten); (7) Current models of the capture of recyclable materials in Germany (M. Kerkhoff); (8) The recycling bin as a pilot test in Hanover (R. Middendorf); (9) Position of BellandVision on the implementation of a unified recycling bin (J. Soelling); (10) What will change with the new Recycle Economy Law according to the material flows and waste treatment capacities? (H. Alwast); (11) Waste management plan Saxony-Anhalt - Current developments (S. Hagel); (12) Wastes from the thermal waste treatment - Risk potential and disposal (G.-R. Behr); (13) Landfill Mining - Contribution of the waste management to the securing of resources (K. Fricke); (14) Logistic process design and system design in the transport of wastes in developing countries using Serbia as an example (Z. Jovanovic); (15) Example of good practices in the subsequent use of landfills - Solar park Cracauer Anger (M. Harnack); (16) Ecoloop - energy efficient gasification in the limestone moving-bed (R. Moeller); (17) Utilization of waste and biomass as a resource? Only by means of an intelligent logistics. (S. Trojahn); (18) Renewable energy resources - Experiences of a network provider (J. Kempmann).

Evaluation of a treatment system type septic tank - filter anaerobic of upward flow for the residual waters of the ecological benefit of the coffee

International Nuclear Information System (INIS)

Sanchez C, Jose Alejandro

1997-01-01

Colombia is the first country in the production of soft coffee in the world. The benefit for humid way it makes that this quality of coffee is obtained; however, the high consumption of water in the process and the later discharge to the superficial or underground sources, they have generated an environmental problem of great magnitude. Also, the sources of water that they have been contaminated with the discharges of the liquid waste that come from benefit of coffee they present, among other, serious inconveniences to be used as supplying sources of drinkable water. In time of crop, the coffee areas and their superficial sources of water usually register high indexes of contamination like consequence of the discharges of residual waters that come from the benefit of the coffee. In the Departments of Quindio, Valle, Caldas, Antioquia, etc., they have been come executing investigations of the residuals treatment that are derived of the pulp removal of the coffee (via humid), for anaerobic methods with satisfactory results. This project had the collaboration of the Departmental Committee of Coffee of Antioquia and the Environmental Engineering of the Antioquia University and it is formulated toward the evaluation of a Anaerobic filter of Ascendant flow, FAFA, preceded of a septic tank (biological sedimentation), as a treatment system of the coffee residual waters, with a waste native of a ecological benefit area. The obtained results were satisfactory although the generated waste is very intermittent and in times that are not of coffee crop it doesn't take place; what hinders more the application of biological systems for its treatment

Evaluation of waste treatment technologies by LLWDDD [Low-Level Waste Disposal Development and Demonstration] Programs

International Nuclear Information System (INIS)

Kennerly, J.M.; Williams, L.C.; Dole, L.R.; Genung, R.K.

1987-01-01

Waste treatments are divided into four categories: (1) volume reduction; (2) conditioning to improve waste form performance; (3) segregation to achieve waste reduction; and (4) separation to remove radioactive (or hazardous) constituents. Two waste treatment demonstrations are described. In the first, volume reduction by mechanical means was achieved during the supercompaction of 300 55-gal drums of solid waste at ORNL. In the second demonstration, conditioning of waste through immobilization and packaging to improve the performance of the waste form is being evaluated. The final section of this paper describes potential scenarios for the management of uranium-contaminated wastes at the Y-12 Plant in Oak Ridge and emphasizes where demonstrations of treatment technology will be needed to implement the scenarios. Separation and thermal treatment are identified as the principal means for treating these wastes. 15 figs

Alpha wastes treatment

International Nuclear Information System (INIS)

Thouvenot, P.

2000-01-01

Alter 2004, the alpha wastes issued from the Commissariat a l'Energie Atomique installations will be sent to the CEDRA plant. The aims of this installation are decontamination and wastes storage. Because of recent environmental regulations concerning ozone layer depletion, the use of CFC 113 in the decontamination unit, as previously planned, is impossible. Two alternatives processes are studied: the AVD process and an aqueous process including surfactants. Best formulations for both processes are defined issuing degreasing kinetics. It is observed that a good degreasing efficiency is linked to a good decontamination efficiency. Best results are obtained with the aqueous process. Furthermore, from the point of view of an existing waste treatment unit, the aqueous process turns out to be more suitable than the AVD process. (author)

Waste treatment

International Nuclear Information System (INIS)

Davies, D.; Hooper, E.W.

1981-01-01

In the treatment of wastes, such as liquid radioactive effluents, it is known to remove radionuclides by successive in situ precipitation of cobalt sulphide, an hydroxide, barium sulphate and a transition element ferrocyanide, followed by separation of the thereby decontaminated effluent. In this invention, use is made of precipitates such as obtained above in the treatment of further fresh liquid radioactive effluent, when it is found that the precipitates have additional capacity for extracting radionuclides. The resulting supernatant liquor may then be subjected to a further precipitation treatment such as above. Decontamination factors for radionuclides of Ce, Ru, Sr and Cs have been considerably enhanced. (author)

Life cycle assessment of electronic waste treatment.

Science.gov (United States)

Hong, Jinglan; Shi, Wenxiao; Wang, Yutao; Chen, Wei; Li, Xiangzhi

2015-04-01

Life cycle assessment was conducted to estimate the environmental impact of electronic waste (e-waste) treatment. E-waste recycling with an end-life disposal scenario is environmentally beneficial because of the low environmental burden generated from human toxicity, terrestrial ecotoxicity, freshwater ecotoxicity, and marine ecotoxicity categories. Landfill and incineration technologies have a lower and higher environmental burden than the e-waste recycling with an end-life disposal scenario, respectively. The key factors in reducing the overall environmental impact of e-waste recycling are optimizing energy consumption efficiency, reducing wastewater and solid waste effluent, increasing proper e-waste treatment amount, avoiding e-waste disposal to landfill and incineration sites, and clearly defining the duties of all stakeholders (e.g., manufacturers, retailers, recycling companies, and consumers). Copyright © 2015 Elsevier Ltd. All rights reserved.

Reduction of heavy metals in residues from the dismantling of waste electrical and electronic equipment before incineration.

Science.gov (United States)

Long, Yu-Yang; Feng, Yi-Jian; Cai, Si-Shi; Hu, Li-Fang; Shen, Dong-Sheng

2014-05-15

Residues disposal from the dismantling of waste electrical and electronic equipment are challenging because of the large waste volumes, degradation-resistance, low density and high heavy metal content. Incineration is advantageous for treating these residues but high heavy metal contents may exist in incinerator input and output streams. We have developed and studied a specialized heavy metal reduction process, which includes sieving and washing for treating residues before incineration. The preferable screen aperture for sieving was found to be 2.36mm (8 meshes) in this study; using this screen aperture resulted in the removal of approximately 47.2% Cu, 65.9% Zn, 26.5% Pb, 55.4% Ni and 58.8% Cd from the residues. Subsequent washing further reduces the heavy metal content in the residues larger than 2.36mm, with preferable conditions being 400rpm rotation speed, 5min washing duration and liquid-to-solid ratio of 25:1. The highest cumulative removal efficiencies of Cu, Zn, Pb, Ni and Cd after sieving and washing reached 81.1%, 61.4%, 75.8%, 97.2% and 72.7%, respectively. The combined sieving and washing process is environmentally friendly, can be used for the removal of heavy metals from the residues and has benefits in terms of heavy metal recycling. Copyright © 2014 Elsevier B.V. All rights reserved.

EPA/DOE joint efforts on mixed waste treatment

International Nuclear Information System (INIS)

Lee, C.C.; Huffman, G.L.; Nalesnik, R.P.

1995-01-01

Under the requirements of the Federal Facility Compliance Act (FFCA), the Department of Energy (DOE) is directed to develop treatment plans for their stockpile of wastes generated at their various sites. As a result, DOE is facing the monumental problem associated with the treatment and ultimate disposal of their mixed (radioactive and hazardous) waste. Meanwhile, the Environmental Protection Agency (EPA) issued a final open-quotes Hazardous Waste Combustion Strategyclose quotes in November 1994. Under the Combustion Strategy, EPA permit writers have been given the authority to use the Omnibus Provision of the Resource Conservation and Recovery Act (RCRA) to impose more stringent emission limits for waste combustors prior to the development of new regulations. EPA and DOE established a multi-year Interagency Agreement (IAG) in 1991. The main objective of the IAG (and of the second IAG that was added in 1993) is to conduct a research program on thermal technologies for treating mixed waste and to establish permit procedures for these technologies particularly under the new requirements of the above-mentioned EPA Combustion Strategy. The objective of this Paper is to summarize the results of the EPA/DOE joint efforts on mixed waste treatment since the establishment of the original Interagency Agreement. Specifically, this Paper will discuss six activities that have been underway; namely: (1) National Technical Workgroup (NTW) on Mixed Waste Treatment, (2) State-of-the-Art Assessment of APC (Air Pollution Control) and Monitoring Technologies for the Rocky Flats Fluidized Bed Unit, (3) Initial Study of Permit open-quotes Roadmapclose quotes Development for Mixed Waste Treatment, (4) Risk Assessment Approach for a Mixed Waste Thermal Treatment Facility, (5) Development and Application of Technology Selection Criteria for Mixed Waste Thermal Treatment, and (6) Performance Testing of Mixed Waste Incineration: In-Situ Chlorine Capture in a Fluidized Bed Unit

The Hybrid Treatment Process for treatment of mixed radioactive and hazardous wastes

International Nuclear Information System (INIS)

Ross, W.A.; Kindle, C.H.

1992-04-01

This paper describes a new process for treating mixed hazardous and radioactive waste, commonly called mixed waste. The process is called the Hybrid Treatment Process (HTP), so named because it is built on the 20 years of experience with vitrification of wastes in melters, and the 12 years of experience with treatment of wastes by the in situ vitrification (ISV) process

treatment of waste effluents using active carbon prepared from AGRO-residues

International Nuclear Information System (INIS)

Yakout, S.M.E.

2006-01-01

the main goal of the investigation is to improve the efficiency of adsorption of radionuclides and anions from liquid waste by modifying sorption properties of adsorbents . thus, the present study is directed towards investigating the feasibility of using agricultural wastes and locally available materials in such a manner as to treat waste effluents. activated carbons derived from rice straw were prepared by one-step steam pyrolysis. the activated rice straw was subjected to liquid-phase oxidation by different modifying agents include KOH, HNO 3 .H 2 So 4 , H 2 O 2 , and kMno 4 to obtain carbon with various surface characters. the prepared carbon samples were characterized using various techniques: x-ray diffraction, pore parameters analysis, point of zero charge pHpzc, FTIR. Boehm titration method. elemental analysis, iodine number, methylene blue, and phenol index. the prepared carbon samples were tested for removal of certain cation pollutants of nuclear interest from waste solutions such as uranium and thorium as well as anion pollutants such as fluoride, nitrate and nitrite.factors affecting the sorption behaviour e.g. carbon properties . contact time ,initial concentration of the solute, mass of adsorbent, ph of solution and temperature were studied by applying batch technique.thorium. fluoride, and nitrate sorption are better occurred at lower temperature while uranium is favoured at higher temperature. the adsorption followed the langmuir adsorption isotherm model in case of uranium and thorium while anions followed langmuir-freundlich isotherm . the ability of RS 2 /kMno 4 to remove F-from egyptian crude phosphoric acid (P 2 O 5 =48.42%) was tested and the adsorption capacity of F - in H 3 PO 4 was greater than that in distilled water due to lower ph enhances f-adsorption onto RS 2 /kMnO 4 carbon

Recovery of fissile materials from plutonium residues, miscellaneous spent nuclear fuel, and uranium fissile wastes

International Nuclear Information System (INIS)

Forsberg, C.W.

1997-01-01

A new process is proposed that converts complex feeds containing fissile materials into a chemical form that allows the use of existing technologies (such as PUREX and ion exchange) to recover the fissile materials and convert the resultant wastes to glass. Potential feed materials include (1) plutonium scrap and residue, (2) miscellaneous spent nuclear fuel, and (3) uranium fissile wastes. The initial feed materials may contain mixtures of metals, ceramics, amorphous solids, halides, and organics. 14 refs., 4 figs

Optimisation of industrial wastes reuse as construction materials.

Science.gov (United States)

Collivignarelli, C; Sorlini, S

2001-12-01

This study concerns the reuse of two inorganic wastes, foundry residues and fly ashes from municipal solid waste incineration, as "recycled aggregate" in concrete production. This kind of reuse was optimised by waste treatment with the following steps: waste washing with water; waste stabilisation-solidification treatment with inorganic reagents; final grinding of the stabilised waste after curing for about 10-20 days. Both the treated wastes were reused in concrete production with different mix-designs. Concrete specimens were characterised by means of conventional physical-mechanical tests (compression, elasticity modulus, shrinkage) and different leaching tests. Experimental results showed that a good structural and environmental quality of "recycled concrete" is due both to a correct waste treatment and to a correct mix-design for concrete mixture.

Acid transformation of bauxite residue: Conversion of its alkaline characteristics

OpenAIRE

Kong, X.; Li, M.; Xue, S.; Hartley, W.; Chen, C.; Wu, C.; Li, X.; Li, Y.

2016-01-01

Bauxite residue (BR) is a highly alkaline solid hazardous waste produced from bauxite processing for alumina production. Alkaline transformation appears to reduce the environmental risk of bauxite residue disposal areas (BRDAs) whilst potentially providing opportunities for the sustainable reuse and on-going management of BR. Mineral acids, a novel citric acid and a hybrid combination of acid-gypsum treatments were investigated for their potential to reduce residue pH and total alkalinity and...

The micro-electrolysis technique in waste water treatment

International Nuclear Information System (INIS)

Jiti Zhou; Weihen Yang; Fenglin Yang; Xuemin Xiang; Yulu Wang

1997-01-01

The micro-electrolysis is one of the efficient methods to treat some kinds of waste water. The experiments have shown its high efficiency in sewage treatment and some kinds of industrial waste water. It is suitable for pre-treatment of high concentrated waste water and deep treatment of waste water for reuse purpose. The disadvantage of micro-electrolysis is its high energy consumption in case of high electrolyte concentration. (author) 2 figs., 11 tabs., 2 refs

The micro-electrolysis technique in waste water treatment

Energy Technology Data Exchange (ETDEWEB)

Jiti Zhou; Weihen Yang; Fenglin Yang; Xuemin Xiang; Yulu Wang [Dalian Univ. of Technology, Dalian (China)

1997-12-31

The micro-electrolysis is one of the efficient methods to treat some kinds of waste water. The experiments have shown its high efficiency in sewage treatment and some kinds of industrial waste water. It is suitable for pre-treatment of high concentrated waste water and deep treatment of waste water for reuse purpose. The disadvantage of micro-electrolysis is its high energy consumption in case of high electrolyte concentration. (author) 2 figs., 11 tabs., 2 refs.

Technology for commercial radioactive waste management

International Nuclear Information System (INIS)

1979-05-01

Conceptual processes and facilities for treating gaseous and various transuranium (TRU) wastes produced during the past fission portion of the light water reactor fuel cycle are described in volume 2. The goal of the treatment process for TRU wastes and for long-lived radionuclides removed from the gaseous waste streams is to convert these wastes to stable products suitable for placement in geologic isolation repositories. The treatment concepts are based on available technology. They do not necessarily represent an optimum design but are representative of what could be achieved with current technology. In actual applications it is reasonable to expect that there could be some improvement over these concepts that might be reflected in either lower costs or lower environmental impacts or both. These conceptual descriptions do provide a reasonable basis for cost analysis and for development of estimates of environmental impacts. The waste treatment technologies considered here include: high-level waste solidification, packaging of fuel residue, failed equipment and noncombustible waste treatment, general trash and combustible waste treatment, degraded solvent treatment, dilute aqueous waste pretreatment, immobilization of wet and solid wastes, off-gas particle removal systems, fuel reprocessing plant dissolver off-gas treatment, process off-gas treatment, and fuel reprocessing plant atmospheric protection system

UKAEA contract no. 3: miscellaneous solid, liquid and gaseous wastes

International Nuclear Information System (INIS)

Partridge, B.A.

1984-12-01

This document reports work carried out in 1982/83 on the following topics concerned with the treatment and disposal of intermediate level wastes: flowsheeting; dewatering low and medium level radioactive wastes; applications of ultrafiltration in the treatment of radioactive liquid wastes; ion exchange processes; electrical processes for the treatment of medium active liquid wastes; chemical conversion of Zircaloy cladding to oxide; fast reactor fuel element cladding; dissolver residues; fuel cladding and ion exchanger immobilisation - radioactive trials; thermal techniques; development and assessment of medium level waste forms. (U.K.)

Application of biosorbents in treatment of the radioactive liquid waste

International Nuclear Information System (INIS)

Ferreira, Rafael Vicente de Padua

2014-01-01

Radioactive liquid waste containing organic compounds need special attention, because the treatment processes available are expensive and difficult to manage. The biosorption is a potential treatment technique that has been studied in simulated wastes. The biosorption term is used to describe the removal of metals, non-metals and/or radionuclides by a material from a biological source, regardless of its metabolic activity. Among the potential biomasses, agricultural residues have very attractive features, as they allow for the removal of radionuclides present in the waste using a low cost biosorbent. The aim of this study was to evaluate the potential use of different biomass originating from agricultural products (coconut fiber, coffee husk and rice husk) in the treatment of real radioactive liquid organic waste. Experiments with these biomass were made including 1) Preparation, activation and characterization of biomasses; 2) Conducting biosorption assays; and 3) Evaluation of the product of immobilization of biomasses in cement. The biomasses were tested in raw and activated forms. The activation was carried out with diluted HNO 3 and NaOH solutions. Biosorption assays were performed in polyethylene bottles, in which were added 10 mL of radioactive waste or waste dilutions in deionized water with the same pH and 2% of the biomass (w/v). At the end of the experiment, the biomass was separated by filtration and the remaining concentration of radioisotopes in the filtrate was determined by ICP-OES and gamma spectrometry. The studied waste contains natural uranium, americium-241 and cesium-137. The adopted contact times were 30 min, 1, 2 and 4 hours and the concentrations tested ranged between 10% and 100%. The results were evaluated by maximum experimental sorption capacity and isotherm and kinetics ternary models. The highest sorption capacity was observed with raw coffee husk, with approximate values of 2 mg/g of U (total), 40 x 10 -6 mg/g of Am-241 and 50 x10 -9

Refuse-derived fuel from municipal solid waste residuals : a feasibility study[Manure, biosolids, and organic industrial/commercial residuals in land applications programs : improving beneficial reuse and protection of water quality

Energy Technology Data Exchange (ETDEWEB)

Sturgess, C.; Johnson, R. [Alberta Research Council, Vegreville, AB (Canada). Environmental Technologies; Schubert, J. [EWMC Operations, Edmonton, AB (Canada)

2007-07-01

Edmonton's Waste Management Centre (EWMC) consists of a composting plant and a materials recovery facility, which accepts over 230,000 tonnes of residential waste per year. It removes 74,000 tonnes of residuals from these two facilities through a series of processing and refining stages and landfilling. Alternative waste management strategies are being considered to handle these residuals as the city's landfill site is approaching its maximum capacity. One option that takes advantage of the high calorific value of these residues is gasification. To ensure consistent and uniform gasification, the residuals have to be processed to a homogenous feedstock. This paper outlined the steps that were taken to characterize the four distinct residual streams, process them to a refuse-derived fluff and pelletize mixtures of these four streams with specific additives. The paper discussed pellet criteria; feedstock preparation; the physical and chemical properties of the fluff and pelletized mixture; pelletization; and, cost estimates of the processing stages involved. Last, a summary of the project was provided. The first phase of the project has been completed. The second phase of the project involves the development of the optimum business case, which includes further cost assessment of the feedstock preparation stage; leasing commercial scale equipment to establish efficiency and robustness of the process; assessing an alternative feeding system for the gasification system; and evaluating methanol production using a catalyst to convert the syngas to methanol. 5 tabs., 4 figs.

Determining the release of radionuclides from tank waste residual solids. FY2015 report

Energy Technology Data Exchange (ETDEWEB)

King, William D. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Hobbs, David T. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2015-09-11

Methodology development for pore water leaching studies has been continued to support Savannah River Site High Level Waste tank closure efforts. For FY2015, the primary goal of this testing was the achievement of target pH and Eh values for pore water solutions representative of local groundwater in the presence of grout or grout-representative (CaCO₃ or FeS) solids as well as waste surrogate solids representative of residual solids expected to be present in a closed tank. For oxidizing conditions representative of a closed tank after aging, a focus was placed on using solid phases believed to be controlling pH and E_h at equilibrium conditions. For three pore water conditions (shown below), the target pH values were achieved to within 0.5 pH units. Tank 18 residual surrogate solids leaching studies were conducted over an E_h range of approximately 630 mV. Significantly higher Eh values were achieved for the oxidizing conditions (ORII and ORIII) than were previously observed. For the ORII condition, the target Eh value was nearly achieved (within 50 mV). However, E_h values observed for the ORIII condition were approximately 160 mV less positive than the target. E_h values observed for the RRII condition were approximately 370 mV less negative than the target. Achievement of more positive and more negative E_h values is believed to require the addition of non-representative oxidants and reductants, respectively. Plutonium and uranium concentrations measured during Tank 18 residual surrogate solids leaching studies under these conditions (shown below) followed the general trends predicted for plutonium and uranium oxide phases, assuming equilibrium with dissolved oxygen. The highest plutonium and uranium concentrations were observed for the ORIII condition and the lowest concentrations were observed for the RRII condition. Based on these results, it is recommended that these test methodologies be used to

Treatment of mercury containing waste

Science.gov (United States)

Kalb, Paul D.; Melamed, Dan; Patel, Bhavesh R; Fuhrmann, Mark

2002-01-01

A process is provided for the treatment of mercury containing waste in a single reaction vessel which includes a) stabilizing the waste with sulfur polymer cement under an inert atmosphere to form a resulting mixture and b) encapsulating the resulting mixture by heating the mixture to form a molten product and casting the molten product as a monolithic final waste form. Additional sulfur polymer cement can be added in the encapsulation step if needed, and a stabilizing additive can be added in the process to improve the leaching properties of the waste form.

Molten salt oxidation of mixed wastes: Separation of radioactive materials and Resource Conservation and Recovery Act (RCRA) materials

International Nuclear Information System (INIS)

Bell, J.T.; Haas, P.A.; Rudolph, J.C.

1993-01-01

The Oak Ridge National Laboratory (ORNL) is involved in a program to apply a molten salt oxidation (MSO) process to the treatment of mixed wastes at Oak Ridge and other Department of Energy (DOE) sites. Mixed wastes are defined as those wastes that contain both radioactive components, which are regulated by the atomic energy legislation, and hazardous waste components, which are regulated under the Resource Conservation and Recovery Act (RCRA). A major part of our ORNL program involves the development of separation technologies that are necessary for the complete treatment of mixed wastes. The residues from the MSO treatment of the mixed wastes must be processed further to separate the radioactive components, to concentrate and recycle residues, or to convert the residues into forms acceptable for final disposal. This paper is a review of the MSO requirements for separation technologies, the information now available, and the concepts for our development studies

Mixed waste treatment at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Larsen, M.M.; Hunt, L.F.; Sanow, D.J.

1988-01-01

The Idaho Operations Office of the Department of Energy (DOE) made the decision in 1984 to prohibit the disposal of mixed waste (MW) (combustible waste-toxic metal waste) in the Idaho National Engineering Laboratory (INEL) low-level radioactive waste (LLW) disposal facility. As a result of this decision and due to there being no EPA-permitted MW treatment/storage/disposal (T/S/D) facilities, the development of waste treatment methods for MW was initiated and a storage facility was established to store these wastes while awaiting development of treatment systems. This report discusses the treatment systems developed and their status. 3 refs., 2 figs., 1 tab

Evaluating the technical aspects of mixed waste treatment technologies

International Nuclear Information System (INIS)

Bagaasen, L.M.; Scott, P.A.

1992-10-01

This report discusses treatment of mixed wastes which is thought to be more complicated than treatment of either hazardous or radioactive wastes. In fact, the treatment itself is no more complicated: however, the regulations that define acceptability of the final waste disposal system are significantly more entangled, and sometimes in apparent conflict. This session explores the factors that influence the choice of waste treatment technologies, and expands on some of the limitations to their application. The objective of the presentation is to describe the technical factors that influence potential treatment processes and the ramifications associated with particular selections (for example, the generation of secondary waste streams). These collectively provide a framework for making informed treatment process selections