Analysis of hazardous organic residues from sodium hydrosulfite industry and utilization as raw materials in a novel solid lubricant production

Energy Technology Data Exchange (ETDEWEB)

Shang, Jiwu [State Key Laboratory of Geological Processes and Mineral Resources, National Laboratory of Mineral Materials, School of Materials Science and Technology, China University of Geosciences, Beijing 100083 (China); Zhang, Yihe, E-mail: zyh@cugb.edu.cn [State Key Laboratory of Geological Processes and Mineral Resources, National Laboratory of Mineral Materials, School of Materials Science and Technology, China University of Geosciences, Beijing 100083 (China); Department of Physics and Materials Science, City University of Hong Kong, Tat Chee Avenue, Kowloon, Hong Kong (China); Zhou, Fengshan; Lv, Fengzhu; Han, Feng; Lu, Jinbo; Meng, Xianghai [State Key Laboratory of Geological Processes and Mineral Resources, National Laboratory of Mineral Materials, School of Materials Science and Technology, China University of Geosciences, Beijing 100083 (China); Chu, Paul K. [Department of Physics and Materials Science, City University of Hong Kong, Tat Chee Avenue, Kowloon, Hong Kong (China); Ye, Zhengfang [Department of Environmental Engineering, Key Laboratory of Water and Sediment Sciences of the Ministry of Education, Peking University, Beijing 100871 (China); Xing, Jing [State Key Laboratory of Geological Processes and Mineral Resources, National Laboratory of Mineral Materials, School of Materials Science and Technology, China University of Geosciences, Beijing 100083 (China)

2011-12-30

Highlights: Black-Right-Pointing-Pointer The hazardous organic residual wastes produced by the sodium hydrosulfite industry are analyzed and the main compounds are found to be thiodiglycol and 2,2 Prime -dithiodiethanol. Black-Right-Pointing-Pointer The lubricity of the organic residues is subsequently studied and the homemade solid lubricant is observed to have good lubricity. Black-Right-Pointing-Pointer The clean process is expected to not only have commercial impact but also help to reduce environmental pollution. - Abstract: The hazardous organic residual wastes produced by the sodium hydrosulfite industry are demonstrated to be convertible into a novel solid lubricant. Identification and isolation of the organic residues are achieved by Fourier transform infrared (FTIR) spectroscopy, gas chromatography-mass spectrometry (GC-MS), and nuclear magnetic resonance (NMR). FTIR and GC-MS provide important information about the residues and the two main components obtained by column chromatography are further analyzed by NMR. The main organic residues are found to be thiodiglycol and 2,2 Prime -dithiodiethanol which have potential applications in petroleum drilling because of their S-S and/or C-S functional groups. The lubricity of the organic residues is subsequently studied and the influence of different adsorbents on the lubricity is investigated and discussed. This homemade lubricant is observed to have good lubricity and by increasing the concentration of the commercial solid lubricant M, the lubricity diminishes. The process is expected to not only have commercial impact but also help to reduce environmental pollution.

21 CFR 556.620 - Sulfabromomethazine sodium.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Sulfabromomethazine sodium. 556.620 Section 556... Tolerances for Residues of New Animal Drugs § 556.620 Sulfabromomethazine sodium. Tolerances for residues of sulfabromomethazine sodium in food are established as follows: (a) In the uncooked edible tissues of cattle at 0.1...

Quantification of heavy metals from residual waste and ashes from the treatment plant of residual water Reciclagua and,effects for the health of those workers which manipulate those residuals

International Nuclear Information System (INIS)

Guerrero D, J.J.

2004-01-01

In this work, the technique of leaching using thermostatted column in series is applied, the X-ray diffraction for the identification of the atomic and molecular structure of the toxic metals that are present in the residual muds of the water treatment plant located in the municipality of Lerma Estado de Mexico, named RECICLAGUA, likewise the technique is used of emission spectrometry for plasma and X-ray fluorescence for the qualitative analysis. Its were take samples of residual mud and of incinerated mud of the treatment plant of residual waters of the industrial corridor Toluca -Lerma RECICLAGUA, located in Lerma Estado de Mexico. For this study there were mixed 100 g of residual mud with a solution to 10% of mineral acid or sodium hydroxide according to the case, to adjust the one pH at 2, 5, 7 and 10, it was added bisulfite, of 0.3-1.5 g of dodecyl sulfate sodium and 3.939 of DTPA (triple V) (Diethylene triamine pentaacetate). To this mud and ashes were extracted the toxic and valuable metals by means of the leaching technique using thermostatted columns placed in series that were designed by the Dr. Jaime Vite Torres; it is necessary to make mention that so much the process as the equipment with those that work it was patented by the same one. With the extraction of these metals benefits are obtained, mainly of economic type, achieving the decrease of the volume of those wastes that have been generated; as well as the so much the use of those residuals, once the metals have been eliminated, as of those liquors where the metals were extracted. It was carried out a quantitative analysis using emission spectrometry by plasma in solids by this way to be able to know the content of the present metals in the sample before and later of leaching them, these results reported a great quantity of elements. Another of the techniques employees was the X-ray diffraction analysis that provides an elementary content of the samples, identifying elements that are present in

The early and late effects of digoxin treatment on the sodium transport, sodium content and Na+K+- ATPase or erythrocytes.

Science.gov (United States)

Cumberbatch, M; Zareian, K; Davidson, C; Morgan, D B; Swaminathan, R

1981-01-01

1 Erythrocyte sodium content, sodium transport (ouabain sensitive sodium flux Eos, and ouabain sensitive efflux rate constant ERCos) sodium, potassium activated ouabain sensitive adenosine triphosphatase (Na+K+ATPase) and plasma digoxin were measured in patients during acute digitalisation and in patients who were on long-term digoxin treatment. 2 In the six patients who were studied during digitalisation, the ERCos and Na+K+ATPase activity decreased and erythrocyte sodium content increased during days 2-4 treatment, but there was no change in Eos. 3 In 39 patients on long term digoxin therapy (2-119 months) the erythrocyte sodium content was normal, but the erythrocyte Na+K+ATPase activity was higher than the control group. When the results from these 39 patients were divided according to the duration of treatment it was found that the erythrocyte sodium content was higher in patients treated for 2-4 months than in patients treated for longer periods and the erythrocyte Na+K+ATPase activity increased with duration of treatment. In eight patients (duration of treatment greater than 29 months) in whom ERCos and Eos were measured, ERCos and Eos were higher than the control group. 4 The results suggest that the effects of digoxin on erythrocytes which occur during acute digoxin treatment do not persist in the long term. 5 The possible explanation for the higher ERCos, Eos and Na+K+ATPase activity in patients treated with digoxin for more than 2 months is discussed. PMID:6268133

Residual water treatment for gamma radiation

International Nuclear Information System (INIS)

Mendez, L.

1990-01-01

The treatment of residual water by means of gamma radiation for its use in agricultural irrigation is evaluated. Measurements of physical, chemical, biological and microbiological contamination indicators were performed. For that, samples from the treatment center of residual water of San Juan de Miraflores were irradiated up to a 52.5 kGy dose. The study concludes that gamma radiation is effective to remove parasites and bacteria, but not for removal of the organic and inorganic matter. (author). 15 refs., 3 tabs., 4 figs

Removal of sodium from the component of the sodium purification loop

International Nuclear Information System (INIS)

Kim, Byung Ho; Jeong, Kyung Chai; Jeong, Ji Young; Kim, Jong Man; Choi, Byung Hae; Nam, Ho Yun

2005-01-01

The purpose of a cleaning process is to remove the residual sodium adhering to the component walls once it has been properly drained. It is necessary to clean and decontaminate a component, especially the large components of the primary coolant system; such as the intermediate heat exchangers and the primary pump. Improper and inadequate cleaning has in a number of cases resulted in problems in the storage, handling, and reuse of components. Several types of failures due to improper cleaning procedures have been defined in the past. Inadequate and incomplete removal of sodium results in residues which may contain metallic sodium and alkaline compounds such as sodium hydroxide, sodium oxide, sodium carbonate, and various types of alcoholates. Reinsertion of components containing these compounds into a high-temperature sodium system can result in either the intergranular penetration characteristic of a high-oxygen sodium or an accelerated corrosion due to oxygen. The methods used for cleaning sodium equipment depend on the condition and types of equipment to be cleaned and whether the equipment is to be reused. Cleaning methods are needed that will avoid a deleterious local overheating, material surface degradation or deposits, chemical, physical, or mechanical damage, and external effects. This paper discusses a steam-nitrogen gas cleaning method for the routine applications that permits the reuse of the cold trap in sodium

The sodium level. An inconspicuous but very important parameter in all-volatile treatment

Energy Technology Data Exchange (ETDEWEB)

Bursik, Albert [PowerPlant Chemistry GmbH, Neulussheim (Germany)

2011-07-15

Boiler tube failure due to ''lack of sodium''? This is certainly not a common concern, yet this contribution stresses the importance of the presence of sodium in the boiler water even when applying all-volatile treatment (AVT) as a method of boiler water treatment. Sodium in the cycle (either unintentionally via sodium-contaminated makeup or intentionally through sodium hydroxide additions) may neutralize the possible acidic contaminations and help to avoid boiler tube failures due to hydrogen damage. (orig.)

Mixed-waste treatment -- What about the residuals?

International Nuclear Information System (INIS)

Carlson, T.; Carpenter, C.; Cummins, L.; Haas, P.; MacInnis, J.; Maxwell, C.

1993-01-01

Incineration currently is the best demonstrated available technology for the large inventory of U.S. Department of Energy (DOE) mixed waste. However, molten salt oxidation (MSO) is an alternative thermal treatment technology with the potential to treat a number of these wastes. Of concern for both technologies is the final waste forms, or residuals, that are generated by the treatment process. An evaluation of the two technologies focuses on 10 existing DOE waste streams and current hazardous-waste regulations, specifically for the delisting of ''derived-from'' residuals. Major findings include that final disposal options are more significantly impacted by the type of waste treated and existing regulations than by the type of treatment technology; typical DOE waste streams are not good candidates for delisting; and mass balance calculations indicate that MSO and incineration generate similar quantities (dry) and types of residuals

Turning into carbonate the residual sodium left in BN-350 circuits may alleviate concerns over their long term safe confinement

International Nuclear Information System (INIS)

Rahmani, L

2000-01-01

After the coolant is drained from the reactor vessel and from the primary and secondary circuits of the BN-350 nuclear power plant, what sodium is left in ponds and films may amount to hundreds of kilograms. For the long term safe storage period which is to follow, preliminary safety analyses (e.g. derived from those made for French sodium cooled reactors) might show that the risks incurred through loss of leaktightness are significant. The ingress of moisture into the circuits would generate, by reaction with the sodium, two undesirable products : sodium hydroxide and hydrogene. Even when considering that water would enter the circuits progressively, so that the heat of the reaction does not give rise to over-pressure, some main risk factors remain. The most promising solution to this challenge appears to be the carbonation of the sodium residues, by progressive diffusion of an appropriate association of carbon dioxyde and water vapour through the inert gaseous medium which fills the circuits. The desired product is porous sodium hydrogenocarbonate

In vitro digestible energy of some agricultural residues, as influenced by gamma irradiation and sodium hydroxide

International Nuclear Information System (INIS)

Al-Masri, M.R.

1999-01-01

Experiments have been carried out to study the changes in the values of in vitro apparent organic matter digestibility (IVOMD) and in vitro digestible energy (IVDE) of wheat straw (WS), cotton seed shell (CSS), peanut shell (PS), soybean shell (SS), extracted olive cake (EOC) and extracted unpeeled sunflower seeds (ESS) after irradiation by various doses of gamma radiation (0, 100, 150, 200 kGy) or after spraying with different amounts of sodium hydroxide (NaOH): 0, 2, 4, and 6 g NaOH/25 ml water/100 g DM. The results indicate that there were significant increases in IVOMD and IVDE values for all irradiated samples and for sodium hydroxide treatments except for SS and ESS. Combined treatment of irradiation and sodium hydroxide resulted in a larger increase in the digestible energy than the individual treatments

Validation of an HPLC-UV method for the determination of ceftriaxone sodium residues on stainless steel surface of pharmaceutical manufacturing equipments.

Science.gov (United States)

Akl, Magda A; Ahmed, Mona A; Ramadan, Ahmed

2011-05-15

In pharmaceutical industry, an important step consists in the removal of possible drug residues from the involved equipments and areas. The cleaning procedures must be validated and methods to determine trace amounts of drugs have, therefore, to be considered with special attention. An HPLC-UV method for the determination of ceftriaxone sodium residues on stainless steel surface was developed and validated in order to control a cleaning procedure. Cotton swabs, moistened with extraction solution (50% water and 50% mobile phase), were used to remove any residues of drugs from stainless steel surfaces, and give recoveries of 91.12, 93.8 and 98.7% for three concentration levels. The precision of the results, reported as the relative standard deviation (RSD), were below 1.5%. The method was validated over a concentration range of 1.15-6.92 μg ml(-1). Low quantities of drug residues were determined by HPLC-UV using a Hypersil ODS 5 μm (250×4.6 mm) at 50 °C with an acetonitrile:water:pH 7:pH 5 (39-55-5.5-0.5) mobile phase at flow rate of 1.5 ml min(-1), an injection volume of 20 μl and were detected at 254 nm. A simple, selective and sensitive HPLC-UV assay for the determination of ceftriaxone sodium residues on stainless steel surfaces was developed, validated and applied. Copyright © 2011 Elsevier B.V. All rights reserved.

Electrochemical treatment of evaporated residue of soak liquor generated from leather industry.

Science.gov (United States)

Boopathy, R; Sekaran, G

2013-09-15

The organic and suspended solids present in soak liquor, generated from leather industry, demands treatment. The soak liquor is being segregated and evaporated in solar evaporation pans/multiple effect evaporator due to non availability of viable technology for its treatment. The residue left behind in the pans/evaporator does not carry any reuse value and also faces disposal threat due to the presence of high concentration of sodium chloride, organic and bacterial impurities. In the present investigation, the aqueous evaporated residue of soak liquor (ERSL) was treated by electrochemical oxidation. Graphite/graphite and SS304/graphite systems were used in electrochemical oxidation of organics in ERSL. Among these, graphite/graphite system was found to be effective over SS304/graphite system. Hence, the optimised conditions for the electrochemical oxidation of organics in ERSL using graphite/graphite system was evaluated by response surface methodology (RSM). The mass transport coefficient (km) was calculated based on pseudo-first order rate kinetics for both the electrode systems (graphite/graphite and SS304/graphite). The thermodynamic properties illustrated the electrochemical oxidation was exothermic and non-spontaneous in nature. The calculated specific energy consumption at the optimum current density of 50 mA cm(-2) was 0.41 kWh m(-3) for the removal of COD and 2.57 kWh m(-3) for the removal of TKN. Copyright © 2013 Elsevier B.V. All rights reserved.

Removal of six pesticide residues in cowpea with alkaline electrolysed water.

Science.gov (United States)

Han, Yongtao; Song, Le; An, Quanshun; Pan, Canping

2017-06-01

Reduction of six pesticide residues (isoprocarb, chlorpyrifos, bifenthrin, beta-cypermethrin, difenoconazole and azoxystrobin) in cowpea by alkaline electrolysed water (AlEW) solutions with different pH was investigated. The commonly used washing treatments in household processing were used for comparison. The residue magnitudes were determined by gas chromatography coupled with tandem mass spectrometry (GC-MS/MS). Results showed that the removal effect of AlEW solution on the six pesticides was superior to tap water, 5% sodium chloride, 5% sodium carbonate and 5% acetic acid solution. AlEW with pH 12.2 had more potential to eliminate the six pesticides in cowpeas. Moreover, the reduction of pesticide residues gradually increased with the increase of washing time. This study demonstrated that AlEW solution with pH of 12.2 could be used to reduce pesticide residues on fresh cowpea samples. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Evaluation on double-wall-tube residual stress distribution of sodium-heated steam generator by neutron diffraction and numerical analysis

International Nuclear Information System (INIS)

Kisohara, N.; Suzuki, H.; Akita, K.; Kasahara, N.

2012-01-01

A double-wall-tube is nominated for the steam generator heat transfer tube of future sodium fast reactors (SFRs) in Japan, to decrease the possibility of sodium/water reaction. The double-wall-tube consists of an inner tube and an outer tube, and they are mechanically contacted to keep the heat transfer of the interface between the inner and outer tubes by their residual stress. During long term SG operation, the contact stress at the interface gradually falls down due to stress relaxation. This phenomenon might increase the thermal resistance of the interface and degrade the tube heat transfer performance. The contact stress relaxation can be predicted by numerical analysis, and the analysis requires the data of the initial residual stress distributions in the tubes. However, unclear initial residual stress distributions prevent precious relaxation evaluation. In order to resolve this issue, a neutron diffraction method was employed to reveal the tri-axial (radius, hoop and longitudinal) initial residual stress distributions in the double-wall-tube. Strain gauges also were used to evaluate the contact stress. The measurement results were analyzed using a JAEA's structural computer code to determine the initial residual stress distributions. Based on the stress distributions, the structural computer code has predicted the transition of the relaxation and the decrease of the contact stress. The radial and longitudinal temperature distributions in the tubes were input to the structural analysis model. Since the radial thermal expansion difference between the inner (colder) and outer (hotter) tube reduces the contact stress and the tube inside steam pressure contributes to increasing it, the analytical model also took these effects into consideration. It has been conduced that the inner and outer tubes are contacted with sufficient stresses during the plant life time, and that effective heat transfer degradation dose not occur in the double-wall-tube SG. (authors)

Ignition and combustion of sodium, fire consequences, extinguishment and prevention

International Nuclear Information System (INIS)

Malet, J.C.

1996-01-01

This document presents the results of work carried out at the IPSN on: sodium inflammation, sodium combustion (pool fires and sprayed jet fires), extinguishment (passive means and extinguishing powder), the physico-chemical behaviour of aerosols and their filtration, the protection means of concretes, intervention during and after a fire, treatment of residues, intervention equipment. The calculation codes developed during these studies are described. The experimental basis which allowed the qualification of these codes and the technological means aimed at prevention and sodium fire fighting, was obtained using programmes carried out in the experimental facilities existing in Cadarache or in collaboration with the German teams of Karlsruhe

Ignition and combustion of sodium, fire consequences, extinguishment and prevention

Energy Technology Data Exchange (ETDEWEB)

Malet, J C [Institut de Protection et de Surete Nucleaire, Laboratoire d' Experimentation de Modelisation des Feux, C.E. Cadarache, Saint-Paul-lez-Durance (France). E-mail: malet at ipsncad.cea.fr

1996-07-01

This document presents the results of work carried out at the IPSN on: sodium inflammation, sodium combustion (pool fires and sprayed jet fires), extinguishment (passive means and extinguishing powder), the physico-chemical behaviour of aerosols and their filtration, the protection means of concretes, intervention during and after a fire, treatment of residues, intervention equipment. The calculation codes developed during these studies are described. The experimental basis which allowed the qualification of these codes and the technological means aimed at prevention and sodium fire fighting, was obtained using programmes carried out in the experimental facilities existing in Cadarache or in collaboration with the German teams of Karlsruhe.

Surgical treatment for residual or recurrent strabismus

Directory of Open Access Journals (Sweden)

Tao Wang

2014-12-01

Full Text Available Although the surgical treatment is a relatively effective and predictable method for correcting residual or recurrent strabismus, such as posterior fixation sutures, medial rectus marginal myotomy, unilateral or bilateral rectus re-recession and resection, unilateral lateral rectus recession and adjustable suture, no standard protocol is established for the surgical style. Different surgical approaches have been recommended for correcting residual or recurrent strabismus. The choice of the surgical procedure depends on the former operation pattern and the surgical dosages applied on the patients, residual or recurrent angle of deviation and the operator''s preference and experience. This review attempts to outline recent publications and current opinion in the management of residual or recurrent esotropia and exotropia.

Sodium waste technology: A summary report

International Nuclear Information System (INIS)

Abrams, C.S.; Witbeck, L.C.

1987-01-01

The Sodium Waste Technology (SWT) Program was established to resolve long-standing issues regarding disposal of sodium-bearing waste and equipment. Comprehensive SWT research programs investigated a variety of approaches for either removing sodium from sodium-bearing items, or disposal of items containing sodium residuals. The most successful of these programs was the design, test, and the production operation of the Sodium Process Demonstration Facility at ANL-W. The technology used was a series of melt-drain-evaporate operations to remove nonradioactive sodium from sodium-bearing items and then converting the sodium to storable compounds

Sulfanegen sodium treatment in a rabbit model of sub-lethal cyanide toxicity

International Nuclear Information System (INIS)

Brenner, Matthew; Kim, Jae G.; Lee, Jangwoen; Mahon, Sari B.; Lemor, Daniel; Ahdout, Rebecca; Boss, Gerry R.; Blackledge, William; Jann, Lauren; Nagasawa, Herbert T.; Patterson, Steven E.

2010-01-01

The aim of this study is to investigate the ability of intramuscular and intravenous sulfanegen sodium treatment to reverse cyanide effects in a rabbit model as a potential treatment for mass casualty resulting from cyanide exposure. Cyanide poisoning is a serious chemical threat from accidental or intentional exposures. Current cyanide exposure treatments, including direct binding agents, methemoglobin donors, and sulfur donors, have several limitations. Non-rhodanese mediated sulfur transferase pathways, including 3-mercaptopyruvate sulfurtransferase (3-MPST) catalyze the transfer of sulfur from 3-MP to cyanide, forming pyruvate and less toxic thiocyanate. We developed a water-soluble 3-MP prodrug, 3-mercaptopyruvatedithiane (sulfanegen sodium), with the potential to provide a continuous supply of substrate for CN detoxification. In addition to developing a mass casualty cyanide reversal agent, methods are needed to rapidly and reliably diagnose and monitor cyanide poisoning and reversal. We use non-invasive technology, diffuse optical spectroscopy (DOS) and continuous wave near infrared spectroscopy (CWNIRS) to monitor physiologic changes associated with cyanide exposure and reversal. A total of 35 animals were studied. Sulfanegen sodium was shown to reverse the effects of cyanide exposure on oxyhemoglobin and deoxyhemoglobin rapidly, significantly faster than control animals when administered by intravenous or intramuscular routes. RBC cyanide levels also returned to normal faster following both intramuscular and intravenous sulfanegen sodium treatment than controls. These studies demonstrate the clinical potential for the novel approach of supplying substrate for non-rhodanese mediated sulfur transferase pathways for cyanide detoxification. DOS and CWNIRS demonstrated their usefulness in optimizing the dose of sulfanegen sodium treatment.

Efficacy of omeprazole/sodium bicarbonate treatment in gastroesophageal reflux disease: a systematic review.

Science.gov (United States)

Higuera-de-la-Tijera, Fátima

2018-03-14

Proton pump inhibitors are the most effective medical therapy for gastroesophageal reflux disease, but their onset of action may be slow. To assess the available literature regarding the efficacy of omeprazole/sodium bicarbonate in gastroesophageal reflux patients. A systematic review was conducted. A systematic literature search starting from 2000. Reviewed manuscripts concerning the effectiveness of omeprazole/sodium bicarbonate treatment in gastroesophageal reflux disease were reviewed and the data were extracted. Data were subsequently analyzed with descriptive statistics. This review included information of four studies. Two trials compared the efficacy of omeprazole/sodium bicarbonate versus omeprazole. One study compared the efficacy of once-daily morning or nighttime dosing. And another study compared omeprazole/sodium bicarbonate/alginate versus omeprazole. In total, there was no difference between omeprazole/sodium bicarbonate and omeprazole. However, there is a trend towards more sustained response and a greater proportion of patients with sustained total relief by 30 minutes with omeprazole/sodium bicarbonate. Omeprazole/sodium bicarbonate therapy is not more effective than omeprazole in the treatment of gastroesophageal reflux disease. However, data obtained suggest that it can have a more sustained response and sustained total relief.

Methodology for Extraction of Remaining Sodium of Used Sodium Containers

International Nuclear Information System (INIS)

Jung, Minhwan; Kim, Jongman; Cho, Youngil; Jeong, Jiyoung

2014-01-01

Sodium used as a coolant in the SFR (Sodium-cooled Fast Reactor) reacts easily with most elements due to its high reactivity. If sodium at high temperature leaks outside of a system boundary and makes contact with oxygen, it starts to burn and toxic aerosols are produced. In addition, it generates flammable hydrogen gas through a reaction with water. Hydrogen gas can be explosive within the range of 4.75 vol%. Therefore, the sodium should be handled carefully in accordance with standard procedures even though there is a small amount of target sodium remainings inside the containers and drums used for experiment. After the experiment, all sodium experimental apparatuses should be dismantled carefully through a series of draining, residual sodium extraction, and cleaning if they are no longer reused. In this work, a system for the extraction of the remaining sodium of used sodium drums has been developed and an operation procedure for the system has been established. In this work, a methodology for the extraction of remaining sodium out of the used sodium container has been developed as one of the sodium facility maintenance works. The sodium extraction system for remaining sodium of the used drums was designed and tested successfully. This work will contribute to an establishment of sodium handling technology for PGSFR. (Prototype Gen-IV Sodium-cooled Fast Reactor)

Biological and genetic effects of combined treatments of sodium azide, gamma rays and EMS in barley

International Nuclear Information System (INIS)

Cheng, X.Y.; Gao, M.W.

1988-01-01

Dry seeds of diploid barley were subjected to mutagenic treatments of sodium azide, gamma rays and EMS alone or in combination. Damage (reduction in seedling height, plant height and fertility), the frequency of chimeras in the M1 generation, and the frequency of chlorophyll-deficient mutations as well as morphological mutations in the M2 generation induced by combined treatments were greater than those by either of the single treatments. Synergistic increase in the frequency of chimeras, chlorphyll-deficient mutations and morphological mutations were observed in both sodium azide post-irradiation treatments and pre-EMS treatments; interaction among the mutagens in the treatment combinations on M1 damage was generally subtractive. An 8- to 16-hr soaking period of irradiated seeds in distilled water prior to sodium azide treatment significantly increased chlorophyll mutation frequency, as compared to that from the non-soaking treatment. Damage and frequency of chimeras, chlorophyll mutations and morphological mutations were consistently reduced by the soaking treatment in sodium azide plus EMS treatments. (author)

In-vitro digestible energy of some agricultural residues, as influenced by gamma irradiation and sodium hydroxide

International Nuclear Information System (INIS)

Al-Masri, M.R.

1999-01-01

The effect of various doses of gamma irradiation (0,100,150,200 KGy) and different concentrations of sodium hydroxide on crude fibre (CF), Cell-wall constituents (NDF, ADF, ADL), in vitro organic matter digestibility (IVOMD), gross energy (GE), in vitro digestible energy (IVDE) of wheat straw (W.S) cotton seed shall (C.S.S), peanut shell (P.S), soybean shell (SB.S), extracted olive cake (O.C.E) and extracted sunflower of unpeeled seeds (S.U.E) were investigated. Results indicated that HaOH in the concentrations at (4 and 6%) had significant effects on the CF content of W.S and P.S, E.U.E, SB.S, C.S.S, O.C.E; respectively. Treating S.U.E, W.S and all other residues with NaoH (2,4 and 6%) respectively, decreased the NDF level. Irradiation dose of 200 KGy decreased CF for all residues, and it reduced the NDF for S.U.E and SB.S. However, lower irradiation dose (150 KGy) was good enough to reduce the NDF for W.S, C.S.S, P.S and O.C.E. Combined treatment resulted in better effects in reducing the concentrations of the cell-wall constituents. The digestible energy values (kJ/Kg DM) increased by 1120,1 220, 2110 (W.S); 620, 830, 1000 for P.S; 240, 500, 580 for O.C.E; 500, 850, 870 for S.U.E; 550, 1060, 1200 for SB.S and 1260, 1710, 2070 for C.S.S using 100, 150, 200, KGy respectively, in comparison to unirradiated controls. Also, the IVDE values (Kj/Kg DM) increased by 560, 1050, 1590 for W.S; 310, 460, 650 for P.S; 170, 760, 1530 for C.S.S; 450, 990, 1190 for O.C.E using 2%, 4%, 6% NaOH respectively, in comparison to controls. No changes in the IVDE values for S.U.E and SB.S. Combined treatment resulted in an even better increase in the digestible energy, except S.U.E and SB.S. (Author)

EFFECT OF SODIUM SILICATE TO SODIUM HYDROXIDE RATIOS ON DURABILITY OF GEOPOLYMER MORTARS CONTAINING NATURAL AND ARTIFICIAL POZZOLANS

Directory of Open Access Journals (Sweden)

F. Nurhayat Degirmenci

2017-09-01

Full Text Available This study aims to provide the experimental data on the sulphate and acid performance of geopolymer mortar containing pozzolanic materials such as fly ash (FA, ground granulated blast furnace slag (GGBS and natural zeolite (NZ. The alkaline solution was the combination of sodium silicate and sodium hydroxide solution with the ratio (Na ₂SiO₃/NaOH of 1.0, 2.0 and 3.0. The molarity of sodium hydroxide was fixed as 10. The performances of geopolymer mortar were measured in terms of sodium and magnesium sulphate resistance and sulphuric and hydrochlorich acid resistance with 5% and 10 % concentration after 24 weeks. The evaluations were measured as visual observation, measurement of weight change and residual compressive strength. It has been observed that Na ₂SiO₃/NaOH ratio is effective on residual compressive strength of geopolymer mortar in both sulphate and acid exposure. The higher ratio of Na ₂SiO₃/NaOH results in a higher residual compressive strength. The GGBS based geopolymer mortar has a very good resistance in acid media in terms of weight loss and residual compressive strength. The inclusion of FA in the GGBS based geopolymer mixture was found to be a suitable base of geopolymer mortar under ambient curing conditions.

Thermal treatment of solid residues from WtE units: A review

International Nuclear Information System (INIS)

Lindberg, Daniel; Molin, Camilla; Hupa, Mikko

2015-01-01

Highlights: • We review the thermal treatment methods for ashes and residues from WtE plants. • We review the results from extensive laboratory work on vitrification, melting and vaporization of ash. • We analyze the results from the extensive patent literature on thermal treatment. • We review industrial concepts for thermal treatment of ash. - Abstract: Thermal treatment methods of bottom ash, fly ash and various types of APC (air pollution control) residues from waste-to-energy plants can be used to obtain environmentally stable material. The thermal treatment processes are meant to reduce the leachability of harmful residue constituents, destroy toxic organic compounds, reduce residue volume, and produce material suitable for utilization. Fly ash and APC residues often have high levels of soluble salts, particularly chlorides, metals such as cadmium, lead, copper and zinc, and trace levels of organic pollutants such as dioxins and furans. Different thermal treatment methods can be used to either decompose or stabilize harmful elements and compounds in the ash, or separate them from the ash to get a material that can be safely stored or used as products or raw materials. In the present paper, thermal treatment methods, such as sintering, vitrification, and melting have been reviewed. In addition to a review of the scientific literature, a survey has been made of the extensive patent literature in the field

Thermal treatment of solid residues from WtE units: A review

Energy Technology Data Exchange (ETDEWEB)

Lindberg, Daniel, E-mail: daniel.lindberg@abo.fi; Molin, Camilla, E-mail: camilla.molin@abo.fi; Hupa, Mikko, E-mail: mikko.hupa@abo.fi

2015-03-15

Highlights: • We review the thermal treatment methods for ashes and residues from WtE plants. • We review the results from extensive laboratory work on vitrification, melting and vaporization of ash. • We analyze the results from the extensive patent literature on thermal treatment. • We review industrial concepts for thermal treatment of ash. - Abstract: Thermal treatment methods of bottom ash, fly ash and various types of APC (air pollution control) residues from waste-to-energy plants can be used to obtain environmentally stable material. The thermal treatment processes are meant to reduce the leachability of harmful residue constituents, destroy toxic organic compounds, reduce residue volume, and produce material suitable for utilization. Fly ash and APC residues often have high levels of soluble salts, particularly chlorides, metals such as cadmium, lead, copper and zinc, and trace levels of organic pollutants such as dioxins and furans. Different thermal treatment methods can be used to either decompose or stabilize harmful elements and compounds in the ash, or separate them from the ash to get a material that can be safely stored or used as products or raw materials. In the present paper, thermal treatment methods, such as sintering, vitrification, and melting have been reviewed. In addition to a review of the scientific literature, a survey has been made of the extensive patent literature in the field.

Anaerobia Treatments of the domestic residual waters. Limitations potentialities

International Nuclear Information System (INIS)

Giraldo Gomez, Eugenio

1993-01-01

The quick growth of the Latin American cities has prevented that an appropriate covering of public services is achieved for the whole population, One of the undesirable consequences of this situation is the indiscriminate discharge from the domestic and industrial residual waters to the nearest bodies of water with its consequent deterioration and with disastrous consequences about the ecology and the public health. The developed countries have controlled this situation using systems of purification of the residual waters previously to their discharge in the receptor source. The same as the technology of the evacuation of the served waters, they have become numerous efforts for the application of the purification systems used in the countries developed to the socioeconomic, climatic and cultural conditions of our means. One of the results obtained in these efforts is the economic inability of the municipalities to pay the high investment costs and of operation of the traditional systems for the treatment of the residual waters. Contrary to another type of public services, the treatment of the residual waters needs of appropriate technological solutions for the Climatic and socioeconomic means of the developing countries, One of the technological alternatives for the purification of the residual waters that has had a great development in the last decades has been that of the biological treatments in t anaerobia ambient. The objective of this contribution is to present, to author's trial, the limitations and potentialities of this technology type with special emphasis in the case of the domestic residual waters

Profile of sodium phenylbutyrate granules for the treatment of urea-cycle disorders: patient perspectives.

Science.gov (United States)

Peña-Quintana, Luis; Llarena, Marta; Reyes-Suárez, Desiderio; Aldámiz-Echevarria, Luis

2017-01-01

Urea-cycle disorders are a group of rare hereditary metabolic diseases characterized by deficiencies of one of the enzymes and transporters involved in the urea cycle, which is necessary for the removal of nitrogen produced from protein breakdown. These hereditary metabolic diseases are characterized by hyperammonemia and life-threatening hyperammonemic crises. Pharmacological treatment of urea-cycle disorders involves alternative nitrogen-scavenging pathways. Sodium benzoate combines with glycine and phenylacetate/phenylbutyrate with glutamine, forming, respectively, hippuric acid and phenylacetylglutamine, which are eliminated in the urine. Among the ammonia-scavenging drugs, sodium phenylbutyrate is a well-known long-term treatment of urea-cycle disorders. It has been used since 1987 as an investigational new drug, and was approved for marketing in the US in 1996 and the EU in 1999. However, sodium phenylbutyrate has an aversive odor and taste, which may compromise patients' compliance, and many patients have reported difficulty in taking this drug. Sodium phenylbutyrate granules are a new tasteless and odor-free formulation of sodium phenylbutyrate, which is indicated in the treatment of urea-cycle disorders. This recently developed taste-masked formulation of sodium phenylbutyrate granules was designed to overcome the considerable issues that taste has on adherence to therapy. Several studies have reported the clinical experience of patients with urea-cycle disorders treated with this new tasteless formulation of sodium phenylbutyrate. Analysis of the data indicated that this taste-masked formulation of sodium phenylbutyrate granules improved quality of life for urea-cycle disorder patients. Furthermore, a postmarketing report on the use of the product has confirmed the previous observations of improved compliance, efficacy, and safety with this taste-masked formulation of sodium phenylbutyrate.

Profile of sodium phenylbutyrate granules for the treatment of urea-cycle disorders: patient perspectives

Directory of Open Access Journals (Sweden)

Peña-Quintana L

2017-09-01

Full Text Available Luis Peña-Quintana,1–3 Marta Llarena,2 Desiderio Reyes-Suárez,2 Luis Aldámiz-Echevarria4 1Pediatric Gastroenterology, Hepatology, and Nutrition Unit, Universitario Materno-Infantil Hospital de Canarias, University of Las Palmas de Gran Canaria, 2Research Institute of Biomedical and Health Sciences, University of Las Palmas de Gran Canaria, Las Palmas, 3CIBEROBN, Madrid, 4Unit of Metabolism, Cruces University Hospital, BioCruces Health Research Institute, GCV-CIBER de Enfremedades Raras (CIBERER, Barakaldo, Spain Abstract: Urea-cycle disorders are a group of rare hereditary metabolic diseases characterized by deficiencies of one of the enzymes and transporters involved in the urea cycle, which is necessary for the removal of nitrogen produced from protein breakdown. These hereditary metabolic diseases are characterized by hyperammonemia and life-threatening hyperammonemic crises. Pharmacological treatment of urea-cycle disorders involves alternative nitrogen-scavenging pathways. Sodium benzoate combines with glycine and phenylacetate/phenylbutyrate with glutamine, forming, respectively, hippuric acid and phenylacetylglutamine, which are eliminated in the urine. Among the ammonia-scavenging drugs, sodium phenylbutyrate is a well-known long-term treatment of urea-cycle disorders. It has been used since 1987 as an investigational new drug, and was approved for marketing in the US in 1996 and the EU in 1999. However, sodium phenylbutyrate has an aversive odor and taste, which may compromise patients’ compliance, and many patients have reported difficulty in taking this drug. Sodium phenylbutyrate granules are a new tasteless and odor-free formulation of sodium phenylbutyrate, which is indicated in the treatment of urea-cycle disorders. This recently developed taste-masked formulation of sodium phenylbutyrate granules was designed to overcome the considerable issues that taste has on adherence to therapy. Several studies have reported the

Pegaptanib sodium treatment in neovascular age-related macular degeneration: clinical experience in Germany

Directory of Open Access Journals (Sweden)

Nikolaus Feucht

2008-06-01

Full Text Available Nikolaus Feucht, Huebner Matthias, Chris P Lohmann, Mathias MaierAugenklinik rechts der Isar, Technical University Munich, GermanyBackground: The VEGF Inhibition Study In Ocular Neovascularisation (VISION reported the efficacy of intravitreal (ITV vascular endothelial growth factor (VEGF inhibition with pegaptanib sodium (Macugen® for the treatment of neovascular age-related macular degeneration (AMD. This paper reports clinical experience with pegaptanib sodium for the treatment of occult or minimally classic choroidal neovascularization (CNV due to AMD.Material and methods: The study included 50 eyes (in 49 patients with either occult CNV or minimally classic CNV secondary to neovascular AMD who were not eligible for photodynamic therapy (PDT. Study data were analyzed retrospectively. During the 6-month study, patients were administered an average 2.74 injections of 0.3 mg ITV pegaptanib sodium. Angiography and optical coherence tomography (OCT examinations were carried out and intraocular pressure (IOP and visual acuity (VA were measured at baseline, at 3 months and at 6 months. An eye examination was performed and VA was measured the 2 days following treatment and then again at weeks 4–6, and at 3 and 6 months. OCT, VA, and IOP were also assessed at 1 month.Results: ITV pegaptanib sodium was well tolerated and no treatment complications arose. Mean VA was measured as: 0.37 ± 0.24 at baseline; 0.37 ± 0.25 at 1 month; 0.37 ± 0.25 at 3 months and 0.40 ± 0.26 at 6 months. VA was stabilized in approximately 90% of eyes treated with pegaptanib sodium. OCT examination showed a minimal change in central retinal thickness (CRT during the course of the study, from 251.19 µm at baseline to 251.63 µm at 6 months. No elevation in IOP was measured during treatment at 4–6 months in patients receiving pegaptanib sodium.Conclusions: ITV therapy with pegaptanib sodium for occult and minimally classic CNV secondary to neovascular AMD offered good

Cleaning of Sodium in the Cold Trap

International Nuclear Information System (INIS)

Kim, Byung Ho; Jeong, Ji Young; Kim, Jong Man; Choi, Byung Hae; Nam, Ho Yun

2005-01-01

The purpose of a cleaning process is to remove the residual sodium adhering to the component walls once it has been properly drained. It is necessary to clean and decontaminate a component, especially the large components of the primary coolant system; such as the intermediate heat exchangers and the primary pump. Improper and inadequate cleaning has in a number of cases resulted in problems in the storage, handling, and reuse of components. Several types of failures due to improper cleaning procedures have been defined in the past. Inadequate and incomplete removal of sodium results in residues which may contain metallic sodium and alkaline compounds such as sodium hydroxide, sodium oxide, sodium carbonate, and various types of alcoholates. Reinsertion of components containing these compounds into a high-temperature sodium system can result in either the intergranular penetration characteristic of a high- oxygen sodium or an accelerated corrosion due to oxygen. The methods used for cleaning sodium equipment depend on the condition and types of equipment to be cleaned and whether the equipment is to be reused. Cleaning methods are needed that will avoid a deleterious local overheating, material surface degradation or deposits, chemical, physical, or mechanical damage, and external effects. This paper discusses a steam-nitrogen gas cleaning method for the routine applications that permits the reuse of the cold trap in sodium

Methods in the treatment of sodium wastes

International Nuclear Information System (INIS)

Rodriguez, G.

1997-01-01

In the domain of sodium waste processing, we have followed a logical route that has enabled us to propose a global method with respect to sodium wastes. This approach has led to: The choice of only those sodium processes using water; The development of sodium purification methods; The development of methods for cutting metallic wastes soiled by or filled with sodium; The transformation of the resulting sodium hydroxide into ultimate solid wastes for surface storage. (author)

Thermal treatment of solid residues from WtE units: a review.

Science.gov (United States)

Lindberg, Daniel; Molin, Camilla; Hupa, Mikko

2015-03-01

Thermal treatment methods of bottom ash, fly ash and various types of APC (air pollution control) residues from waste-to-energy plants can be used to obtain environmentally stable material. The thermal treatment processes are meant to reduce the leachability of harmful residue constituents, destroy toxic organic compounds, reduce residue volume, and produce material suitable for utilization. Fly ash and APC residues often have high levels of soluble salts, particularly chlorides, metals such as cadmium, lead, copper and zinc, and trace levels of organic pollutants such as dioxins and furans. Different thermal treatment methods can be used to either decompose or stabilize harmful elements and compounds in the ash, or separate them from the ash to get a material that can be safely stored or used as products or raw materials. In the present paper, thermal treatment methods, such as sintering, vitrification, and melting have been reviewed. In addition to a review of the scientific literature, a survey has been made of the extensive patent literature in the field. Copyright © 2015 Elsevier Ltd. All rights reserved.

Final Environmental Impact Statement for the Treatment and Management of Sodium-Bonded Spent Nuclear Fuel

International Nuclear Information System (INIS)

2000-01-01

DOE is responsible for the safe and efficient management of its sodium-bonded spent nuclear fuel. This fuel contains metallic sodium, a highly reactive material; metallic uranium, which is also reactive; and in some cases, highly enriched uranium. The presence of reactive materials could complicate the process of qualifying and licensing DOE's sodium-bonded spent nuclear fuel inventory for disposal in a geologic repository. Currently, more than 98 percent of this inventory is located at the Idaho National Engineering and Environmental Laboratory (INEEL), near Idaho Falls, Idaho. In addition, in a 1995 agreement with the State of Idaho, DOE committed to remove all spent nuclear fuel from Idaho by 2035. This EIS evaluates the potential environmental impacts associated with the treatment and management of sodium-bonded spent nuclear fuel in one or more facilities located at Argonne National Laboratory-West (ANL-W) at INEEL and either the F-Canyon or Building 105-L at the Savannah River Site (SRS) near Aiken, South Carolina. DOE has identified and assessed six proposed action alternatives in this EIS. These are: (1) electrometallurgical treatment of all fuel at ANL-W, (2) direct disposal of blanket fuel in high-integrity cans with the sodium removed at ANL-W, (3) plutonium-uranium extraction (PUREX) processing of blanket fuel at SRS, (4) melt and dilute processing of blanket fuel at ANL-W, (5) melt and dilute processing of blanket fuel at SRS, and (6) melt and dilute processing of all fuel at ANL-W. In addition, Alternatives 2 through 5 include the electrometallurgical treatment of driver fuel at ANL-W. Under the No Action Alternative, the EIS evaluates both the continued storage of sodium-bonded spent nuclear fuel until the development of a new treatment technology or direct disposal without treatment. Under all of the alternatives, the affected environment is primarily within 80 kilometers (50 miles) of spent nuclear fuel treatment facilities. Analyses indicate

Sodium valproate for the treatment of mania in a patient with Charcot ...

African Journals Online (AJOL)

and the treatment thereof with sodium valproate. Mr. L, a 28 ... prolonged distal latencies, decreased compound muscle action ... 1000mg per day for treatment of mania. ... dystrophy, facio-scapulo-humeral dystrophy, and hereditary motor and.

Immobilization in ceramic waste forms of the residues from treatment of mixed wastes

International Nuclear Information System (INIS)

Oversby, V.M.; van Konynenburg, R.A.; Glassley, W.E.; Curtis, P.G.

1993-11-01

The Environmental Restoration and Waste Management Applied Technology Program at LLNL is developing a Mixed Waste Management Facility to demonstrate treatment technologies that provide an alternative to incineration. As part of that program, we are developing final waste forms using ceramic processing methods for the immobilization of the treatment process residues. The ceramic phase assemblages are based on using Synroc D as a starting point and varying the phase assemblage to accommodate the differences in chemistry between the treatment process residues and the defense waste for which Synroc D was developed. Two basic formulations are used, one for low ash residues resulting from treatment of organic materials contaminated with RCRA metals, and one for high ash residues generated from the treatment of plastics and paper products. Treatment process residues are mixed with ceramic precursor materials, dried, calcined, formed into pellets at room temperature, and sintered at 1150 to 1200 degrees C to produce the final waste form. This paper discusses the chemical composition of the waste streams and waste forms, the phase assemblages that serve as hosts for inorganic waste elements, and the changes in waste form characteristics as a function of variation in process parameters

One Year Experience of Pheburane(®) (Sodium Phenylbutyrate) Treatment in a Patient with Argininosuccinate Lyase Deficiency.

Science.gov (United States)

Uçar, Sema Kalkan; Ozbaran, Burcu; Altinok, Yasemin Atik; Kose, Melis; Canda, Ebru; Kagnici, Mehtap; Coker, Mahmut

2015-01-01

Argininosuccinate lyase deficiency (ASLD) is a urea cycle disorder (UCD) treated with dietary adjustment and nitrogen scavenging agents. "Pheburane(®)" is a new tasteless and odour-free formulation of sodium phenylbutyrate, indicated in the treatment of UCD.A male patient diagnosed with ASLD was put on treatment with the new formulation of sodium phenylbutyrate (granules) for a period of one year, at 500 mg/kg orally in 3 intakes/day. Plasma glutamine, arginine, citrulline, argininosuccinate, serum sodium, potassium, liver function tests and urine orotate all remained unchanged over this period. There was no difference in mean ammonia levels before and after treatment, and no hyperammonemia episode occurred during treatment with Pheburane(®). An improvement in a measurement of quality of life (QOL) was noted after treatment with Pheburane(®). Good metabolic control and improved QOL were achieved throughout the treatment period.

Selenium-Water Treatment Residual Adsorption And Characterization

Science.gov (United States)

Aluminum-based water treatment residuals (WTR) have the ability to adsorb tremendous quantities of soil-borne P, and have been shown to adsorb other anions, such as As (V), As (III), and ClO4-. Environmental issues associated with Se in the Western US led us to study W...

Sodium butyrate stimulates cellular recovery from UV damage in xeroderma pigmentosum cells belonging to complementation group F

International Nuclear Information System (INIS)

Nishigori, Chikako; Takebe, Hiraku

1987-01-01

Possible stimulation of the DNA repair capacity by sodium butyrate in normal and xeroderma pigmentosum (XP) cells was investigated. XP cells belonging to the complementation group F showed considerable stimulation of DNA repair by sodium butyrate in terms of both the amount of unscheduled DNA synthesis (UDS) and the colony-forming ability after UV irradiation. UDS in XP cells belonging to the complementation group A was not enhanced, while normal cells showed slight enhancement, but less than that of XP F cells. In XP A, XP C, and normal cells, sodium butyrate treatment enhanced the killing effect of UV irradiation. The residual repair capacity in XP F cells appeared to be stimulated by sodium butyrate. (author)

Treatment of writer's sodium valproate and cramp with baclofen

African Journals Online (AJOL)

Treatment of a 27-year-old Black man with writer's cramp with a combin'ation of sodium valproate (Epi- lim) and baclofen (Lioresal) resulted in dramatic improvement of symptoms and signs. The possible mechanism of action of these drugs is discussed. This combination should be tried in the initial man- agement of this ...

The renal handling of sodium and water is not affected by the standard-dose cisplatin treatment for testicular cancer

DEFF Research Database (Denmark)

Daugaard, G; Strandgaard, S; Holstein-Rathlou, N H

1987-01-01

Renal clearances of 51Cr-EDTA, lithium, sodium and potassium were measured before and after each of four consecutive treatment series with cisplatin in 15 men with testicular cancer. Since lithium is reabsorbed like sodium and water in the proximal tubules, but not reabsorbed to any measurable...... and all other parameters of glomerular filtration and renal sodium handling remained normal throughout the study (with the exception of a fall in fractional sodium excretion after the first treatment series). Plasma magnesium declined during all four treatment periods, signifying renal magnesium wasting....

Quantification of heavy metals from residual waste and ashes from the treatment plant of residual water Reciclagua and,effects for the health of those workers which manipulate those residuals; Cuantificacion de metales pesados de lodo residual y cenizas de la planta tratadora de aguas residuales Reciclagua y efectos a la salud de los trabajadores que manipulan los residuos

Energy Technology Data Exchange (ETDEWEB)

Guerrero D, J.J

2004-07-01

In this work, the technique of leaching using thermostatted column in series is applied, the X-ray diffraction for the identification of the atomic and molecular structure of the toxic metals that are present in the residual muds of the water treatment plant located in the municipality of Lerma Estado de Mexico, named RECICLAGUA, likewise the technique is used of emission spectrometry for plasma and X-ray fluorescence for the qualitative analysis. Its were take samples of residual mud and of incinerated mud of the treatment plant of residual waters of the industrial corridor Toluca -Lerma RECICLAGUA, located in Lerma Estado de Mexico. For this study there were mixed 100 g of residual mud with a solution to 10% of mineral acid or sodium hydroxide according to the case, to adjust the one pH at 2, 5, 7 and 10, it was added bisulfite, of 0.3-1.5 g of dodecyl sulfate sodium and 3.939 of DTPA (triple V) (Diethylene triamine pentaacetate). To this mud and ashes were extracted the toxic and valuable metals by means of the leaching technique using thermostatted columns placed in series that were designed by the Dr. Jaime Vite Torres; it is necessary to make mention that so much the process as the equipment with those that work it was patented by the same one. With the extraction of these metals benefits are obtained, mainly of economic type, achieving the decrease of the volume of those wastes that have been generated; as well as the so much the use of those residuals, once the metals have been eliminated, as of those liquors where the metals were extracted. It was carried out a quantitative analysis using emission spectrometry by plasma in solids by this way to be able to know the content of the present metals in the sample before and later of leaching them, these results reported a great quantity of elements. Another of the techniques employees was the X-ray diffraction analysis that provides an elementary content of the samples, identifying elements that are present in

Cation exchange process for molten salt extraction residues

International Nuclear Information System (INIS)

Proctor, S.G.

1975-01-01

A new method, utilizing a cation exchange technique, has been developed for processing molten salt extraction (MSE) chloride salt residues. The developed ion exchange procedure has been used to separate americium and plutonium from gross quantities of magnesium, potassium, and sodium chloride that are present in the residues. The recovered plutonium and americium contained only 20 percent of the original amounts of magnesium, potassium, and sodium and were completely free of any detectable amounts of chloride impurity. (U.S.)

Delayed tooth replantation after root surface treatment with sodium hypochlorite and sodium fluoride: histomorphometric analysis in rats.

Science.gov (United States)

Sottovia, André Dotto; Sonoda, Celso Koogi; Poi, Wilson Roberto; Panzarini, Sônia Regina; Lauris, José Roberto Pereira

2006-04-01

In cases of delayed tooth replantation, non-vital periodontal ligament remnants have been removed with sodium hypochlorite in an attempt to control root resorption. Nevertheless, reports of its irritating potential in contact with the alveolar connective tissue have been described. Therefore, this study evaluated the healing process on delayed replantation of rat teeth, after periodontal ligament removal by different treatment modalities. Twenty-four rats, assigned to 3 groups (n=8), had their upper right incisor extracted and left on the workbench for desiccation during 60 min. Afterwards, the teeth in group I were immersed in saline for 2 min. In group II, root surfaces were scrubbed with gauze soaked in saline for 2 min; and in group III, scrubbing was done with gauze soaked in 1% sodium hypochlorite solution. Thereafter, root surfaces were etched with 37% phosphoric acid and immersed in 2% acidulate-phosphate sodium fluoride solution, at pH 5.5. Root canals were filled with a calcium hydroxide-based paste and the teeth were replanted. The animals were sacrificed 60 days postoperatively and the pieces containing the replanted teeth were processed and paraffin- embedded. Semi-serial transversally sections were obtained from the middle third of the root and stained with hematoxylin and eosin for histomorphometric analysis. Data were analyzed statistically using Kruskal-Wallis and Dunn's tests. The results showed that root structure and cementum extension were more affected by resorption in group III (p<0.05). All groups were affected by root resorption but the treatment performed in group III was the least effective for its control. The treatment accomplished in groups I and II yielded similar results to each other.

Efficacy of bromfenac sodium ophthalmic solution for treatment of dry eye disease.

Science.gov (United States)

Fujishima, Hiroshi; Fuseya, Miki; Ogata, Masarou; Murat, Dogru

2015-01-01

To evaluate the efficacy of bromfenac sodium ophthalmic solution (BF) in patients with dry eye disease (DED) inadequately controlled by monotherapy with artificial tears (ATs). An investigator-oriented trial with a single-arm, nonrandomized, open-label design. Twenty-six patients, who showed no symptomatic improvement of DED after 1 month of AT treatment, were enrolled. Bromfenac sodium ophthalmic solution was administered adjunctively with AT for 1 month. The BF treatment was then discontinued, and AT treatment alone was continued for 3 months. The signs and symptoms were evaluated at the beginning of BF treatment (Pre), at the end of the combined BF and AT treatment (BF1M), and at 1 and 3 months after discontinuation of BF treatment (Po1M and Po3M, respectively). The dryness scores at BF1M were significantly improved compared with Pre (P ophthalmic solution has improved the dryness of the eye and signs of DED through its anti-inflammatory effects. Nonsteroidal anti-inflammatory drugs were suitable as anti-inflammatory ophthalmic solutions for patients with DED.

Hazardous Materials Verification and Limited Characterization Report on Sodium and Caustic Residuals in Materials and Fuel Complex Facilities MFC-799/799A

Energy Technology Data Exchange (ETDEWEB)

Gary Mecham

2010-08-01

This report is a companion to the Facilities Condition and Hazard Assessment for Materials and Fuel Complex Sodium Processing Facilities MFC-799/799A and Nuclear Calibration Laboratory MFC-770C (referred to as the Facilities Condition and Hazards Assessment). This report specifically responds to the requirement of Section 9.2, Item 6, of the Facilities Condition and Hazards Assessment to provide an updated assessment and verification of the residual hazardous materials remaining in the Sodium Processing Facilities processing system. The hazardous materials of concern are sodium and sodium hydroxide (caustic). The information supplied in this report supports the end-point objectives identified in the Transition Plan for Multiple Facilities at the Materials and Fuels Complex, Advanced Test Reactor, Central Facilities Area, and Power Burst Facility, as well as the deactivation and decommissioning critical decision milestone 1, as specified in U.S. Department of Energy Guide 413.3-8, “Environmental Management Cleanup Projects.” Using a tailored approach and based on information obtained through a combination of process knowledge, emergency management hazardous assessment documentation, and visual inspection, this report provides sufficient detail regarding the quantity of hazardous materials for the purposes of facility transfer; it also provides that further characterization/verification of these materials is unnecessary.

Sodium-Bearing Waste Treatment Alternatives Implementation Study

Energy Technology Data Exchange (ETDEWEB)

Charles M. Barnes; James B. Bosley; Clifford W. Olsen

2004-07-01

The purpose of this document is to discuss issues related to the implementation of each of the five down-selected INEEL/INTEC radioactive liquid waste (sodium-bearing waste - SBW) treatment alternatives and summarize information in three main areas of concern: process/technical, environmental permitting, and schedule. Major implementation options for each treatment alternative are also identified and briefly discussed. This report may touch upon, but purposely does not address in detail, issues that are programmatic in nature. Examples of these include how the SBW will be classified with respect to the Nuclear Waste Policy Act (NWPA), status of Waste Isolation Pilot Plant (WIPP) permits and waste storage availability, available funding for implementation, stakeholder issues, and State of Idaho Settlement Agreement milestones. It is assumed in this report that the SBW would be classified as a transuranic (TRU) waste suitable for disposal at WIPP, located in New Mexico, after appropriate treatment to meet transportation requirements and waste acceptance criteria (WAC).

Anaerobic treatment of solid and liquid residues. Papers

International Nuclear Information System (INIS)

Maerkl, H.; Stegmann, R.

1994-01-01

Anaerobic processes are getting increasing attention in the disposal of liquid waste of the food industry and chemical industry and solid organic residues of the municipal sector. The main advantages of anaerobic processes are the favourable energy balance and the comparatively small volume of new biomass produced. There are new satisfactory technical solutions for nearly all problems encountered in practice. A conference on ''Anaerobic treatment of solid and liquid residues'' was held on 2-4 November 1994. The state of the art and new developments were presented in lectures by experts from research and practice. (orig.) [de

Quantitative determination of pefloxacin mesylate by residual-base neutralisation method

Directory of Open Access Journals (Sweden)

HULIKALCHANDRA SHEKAR PRAMEELA

2004-05-01

Full Text Available This work describes two procedures based on residual base determination for the quantification of pefloxacin mesylate (PFM in bulk drug and in pharmaceutical products. In the first method involving titrimetry, the drug solution is treated with a measured excess of sodium hydroxide followed by back titration of the residual base with hydrochloric acid using a phenol red-bromothymol blue mixed indicator. The second spectrophotometrie method involves treatment of a fixed amount of sodium hydroxide – phenol red mixture with varying amounts of the drug, and measuring the decrease in the absorbance of the dye at 560 nm. In the titrimetric method, a reaction stoichiometry of 1:1 was found in the quantification range of 4–20 mg of drug. The spectrophotometric method allows the determination of PFM in the 5–40 mg ml-1 range. The molar absorptivity is 5.91¤103 l mol-1 cm-1 and the Sandell sensitivity is 56.37 ng cm-2. The methods were applied successfully to the determination of PFM in pharmaceutical preparations.

The sodium coolant

International Nuclear Information System (INIS)

Rodriguez, G.

2004-01-01

The sodium is the best appropriate coolant for the fast neutrons reactors technology. Thus the fast neutrons reactors development is intimately bound to the sodium technology. This document presents the sodium as a coolant point of view: atomic structure and characteristics, sodium impacts on the fast neutron reactors technology, chemical properties of the sodium and the consequences, quality control in a nuclear reactor, sodium treatment. (A.L.B.)

Evaluation of various soaking agents as a novel tool for pesticide residues mitigation from cauliflower (Brassica oleracea var. botrytis).

Science.gov (United States)

Abdullah; Randhawa, Muhammad Atif; Asghar, Ali; Pasha, Imran; Usman, Rabia; Shamoon, Muhammad; Bhatti, Muhammad Arslan; Irshad, Muhammad Asim; Ahmad, Naveed

2016-08-01

The increasing use of pesticides for boosting the yield of agricultural crops also impart toxic residues which ultimately extend to numerous physiological disorders upon consumption. The present study was designed as an effort to assess the reduction potential of various chemical solutions and to minimize the pesticide residues in cauliflower ( Brassica oleracea var. botrytis ). The samples were soaked in various solutions along with tap water to mitigate pesticide residues. Afterwards, the extracted supernatant was passed through column containing anhydrous sodium sulfate trailed by activated carbon for clean-up. Eluents were first evaporated and then completely dried under gentle stream of Nitrogen. Finally, the residues were determined using gas chromatography equipped with electron capture detector (GC-ECD). Results revealed the highest reduction of endosulfan, bifenthrin and cypermethrin residues with acetic acid (10 %) was 1.133 ± 0.007 (41 %), 0.870 ± 0.022 (60 %) and 0.403 ± 0.003 (75 %), respectively among the tested solutions. However, simple tap water treatment also resulted in 0.990 ± 0.02 (12 %), 1.323 ± 0.015 (14 %) and 1.274 ± 0.002 (21 %) elimination of endosulfan, bifenthrin and cypermethrin residues, respectively. Moreover, among various solutions, acetic acid depicted maximum reduction potential followed by citric acid, hydrogen peroxide, sodium chloride and sodium carbonate solutions. The percent reduction by various solutions ranged from 12 to 41, 14 to 60 and 21 to 75 % for the elimination of endosulfan, bifenthrin and cypermethrin residues, respectively.

Effects of processing treatment on pesticide residues in fruits and their products

International Nuclear Information System (INIS)

Mao Xuefei; Jiao Bining; Fu Chenmei; Qian Yongzhong; Wang Jing

2008-01-01

The influence of processing treatments on pesticide residues in fruits and their products was reviewed. The effects on pesticide residues and relative control treatments for each processing step, including peeling, washing, sterilization, juicing, clarification, filtration, drying and fermentation, were discussed, respectively. Meanwhile we analyzed the future development prospectin of this field, in order to provide some suggestions for commercial fruit industry and consumers' health. (authors)

Review on the Influences of Bagging Treatment on Pesticide Residue in Fruits

OpenAIRE

ZHAO Xiao-yun; XIE De-fang

2018-01-01

At present, bagging technology has been widely applicated in fruit cultivation. Impact of bagging treatment on the pesticide residues have different results. On the basis of existing achievements, this paper systematically analyzed the influence of different bagging treatments on pesticide residues:such as different ways of applying pesticide, pesticide concentration, number of applying pesticide; bagging materials, bagged layer; the type of pesticide(systemic pesticide, nonendoscopic pestici...

Selenium Adsorption To Aluminum-Based Water Treatment Residuals

Science.gov (United States)

Aluminum-based water treatment residuals (WTR) can adsorb water-and soil-borne P, As(V), As(III), and perchlorate, and may be able to adsorb excess environmental selenium. WTR, clay minerals, and amorphous aluminum hydroxide were shaken for 24 hours in selenate or selenite solut...

Characterisation of some South African water treatment residues ...

African Journals Online (AJOL)

2005-07-03

Jul 3, 2005 ... Land application of water treatment residue (WTR) the by-product from the production of potable water, is becoming the preferred ... were analysed for some physical (particle size distribution, particle density and plant available water) and chemical attributes ...... for Industrial Wastes – Theory and Practice.

Oral Versus Topical Diclofenac Sodium in the Treatment of Osteoarthritis.

Science.gov (United States)

Tieppo Francio, Vinicius; Davani, Saeid; Towery, Chris; Brown, Tony L

2017-06-01

Osteoarthritis (OA) is one of the most common causes of joint pain in the United States and non-steroidal anti-inflammatories (NSAIDs), such as Diclofenac sodium, which is currently available in two main routes of administration; oral and topical distribution have been established as one of the standard treatments for OA. Generally, oral NSAIDs are well tolerated; however our narrative review suggests that the topical solution had a better tolerability property than oral Diclofenac sodium, especially due to side effects of gastrointestinal bleeding with the utilization of the oral format. In addition, the topical route may be considered a reasonable selection by clinicians for management of musculoskeletal pain in those patients with a history of potential risk and adverse side effects. Most studies reviewed comparing oral versus topical solution of Diclofenac sodium revealed comparable efficacy, with minimal side effects utilizing the topical route. The key point of this narrative review is to help clinicians that currently must decide between very inexpensive diclofenac oral presentations and expensive topical presentations especially in the elderly population and the pros and cons of such decision-making process.

A Patient with MSUD: Acute Management with Sodium Phenylacetate/Sodium Benzoate and Sodium Phenylbutyrate

OpenAIRE

K?se, Melis; Canda, Ebru; Kagnici, Mehtap; U?ar, Sema Kalkan; ?oker, Mahmut

2017-01-01

In treatment of metabolic imbalances caused by maple syrup urine disease (MSUD), peritoneal dialysis, and hemofiltration, pharmacological treatments for elimination of toxic metabolites can be used in addition to basic dietary modifications. Therapy with sodium phenylacetate/benzoate or sodium phenylbutyrate (NaPB) in urea-cycle disorder cases has been associated with a reduction in branched-chain amino acid (BCAA) concentrations when the patients are on adequate dietary protein intake. Moreo...

The effect of sludge water treatment plant residuals on the properties of compressed brick

Science.gov (United States)

Shamsudin, Shamrul-Mar; Shahidan, S.; Azmi, M. A. M.; Ghaffar, S. A.; Ghani, M. B. Abdul; Saiful Bahari, N. A. A.; Zuki, S. S. M.

2017-11-01

The focus of this study is on the production of compressed bricks which contains sludge water treatment plant (SWTP) residuals obtained from SAJ. The main objective of this study is to utilise and incorporate discarded material (SWTP) in the form of residual solution to produce compressed bricks. This serves as one of the recycling efforts to conserve the environment. This study determined the optimum mix based on a mix ratio of 1:2:4 (cement: sand: soil) in the production of compressed bricks where 5 different mixes were investigated i. e. 0%, 5%, 10%, 20%, and 30% of water treatment plant residue solution. The production of the compressed bricks is in accordance with the Malaysian Standard MS 7.6: 1972 and British Standard BS 3921: 1985 - Compressive Strength & Water Absorption. After being moulded and air dried, the cured bricks were subjected to compression tests and water absorption tests. Based on the tests conducted, it was found that 20% of water treatment plant residue solution which is equivalent to 50% of soil content replacement with a mix composition of [10: cement] [20: sand] [20: soil] [20: water treatment plant residue solution] is the optimum mix. It was also observed that the bricks containing SWTP residuals were lighter in weight compared to the control specimens

Relaxation of residual stress in MMC after combined plastic deformation and heat treatment

International Nuclear Information System (INIS)

Bruno, G.; Ceretti, M.; Girardin, E.; Giuliani, A.; Manescu, A.

2004-01-01

Neutron Diffraction shows that plastic pre-deformation and heat treatments have opposite effects on the residual stress in Al-SiC p composites. The thermal micro residual stress is relaxed or even reversed by pre-strains above 0.2%, but restored by heat treatments. The sense of relaxation changes above 400 deg. C (the mixing temperature)

Changes in urinary excretion of water and sodium transporters during amiloride and bendroflumethiazide treatment

DEFF Research Database (Denmark)

Jensen, Janni M; Mose, Frank H; Kulik, Anna-Ewa O

2015-01-01

AIM: To quantify changes in urinary excretion of aquaporin2 water channels (u-AQP2), the sodium-potassium-chloride co-transporter (u-NKCC2) and the epithelial sodium channels (u-ENaC) during treatment with bendroflumethiazide (BFTZ), amiloride and placebo. METHODS: In a randomized, double....... General linear model with repeated measures or related samples Friedman's two-way analysis was used to compare differences. Post hoc Bonferroni correction was used for multiple comparisons of post infusion periods to baseline within each treatment group. RESULTS: At baseline there were no differences in u...... by the constant infusion clearance technique with (51)Cr-EDTA as reference substance. To estimate the changes in water transport via AQP2 and sodium transport via NKCC2 and ENaC, u-NKCC2, the gamma fraction of ENaC (u-ENaCγ), and u-AQP2 were measured at baseline and after infusion with 3% hypertonic saline. U...

Effect of cryogenic treatment on distribution of residual stress in case carburized En 353 steel

International Nuclear Information System (INIS)

Bensely, A.; Venkatesh, S.; Mohan Lal, D.; Nagarajan, G.; Rajadurai, A.; Junik, Krzysztof

2008-01-01

The effect of cryogenic treatment on the distribution of residual stress in the case carburized steel (En 353) was studied using X-ray diffraction technique. Two types of cryogenic treatment: shallow cryogenic treatment (193 K) and deep cryogenic treatment (77 K) were adopted, as a supplement to conventional heat treatment. The amount of retained austenite in conventionally heat-treated, shallow cryogenically treated and deep cryogenically treated samples was found to be 28%, 22% and 14%, respectively. The conventionally heat-treated, shallow cryogenically treated and deep cryogenically treated samples in untempered condition had a surface residual stress of -125 MPa, -115 MPa and -235 MPa, respectively. After tempering the conventionally heat-treated, shallow cryogenically treated and deep cryogenically treated samples had a surface residual stress of -150 MPa, -80 MPa and -80 MPa, respectively. A comparative study of the three treatments revealed that there was an increase in the compressive residual stress in steel that was subjected to cryogenic treatment prior to tempering. The experimental investigation revealed that deep cryogenically treated steel when subjected to tempering has undergone a reduction in compressive residual stress. Such stress relieving behaviour was mainly due to the increased precipitation of fine carbides in specimens subjected to DCT with tempering

Prediction of residual metabolic activity after treatment in NSCLC patients

International Nuclear Information System (INIS)

Rios Velazquez, Emmanuel; Aerts, Hugo J.W.L.; Oberije, Cary; Ruysscher, Dirk De; Lambin, Philippe

2010-01-01

Purpose. Metabolic response assessment is often used as a surrogate of local failure and survival. Early identification of patients with residual metabolic activity is essential as this enables selection of patients who could potentially benefit from additional therapy. We report on the development of a pre-treatment prediction model for metabolic response using patient, tumor and treatment factors. Methods. One hundred and one patients with inoperable NSCLC (stage I-IV), treated with 3D conformal radical (chemo)-radiotherapy were retrospectively included in this study. All patients received a pre and post-radiotherapy fluorodeoxyglucose positron emission tomography-computed tomography FDG-PET-CT scan. The electronic medical record system and the medical patient charts were reviewed to obtain demographic, clinical, tumor and treatment data. Primary outcome measure was examined using a metabolic response assessment on a post-radiotherapy FDG-PET-CT scan. Radiotherapy was delivered in fractions of 1.8 Gy, twice a day, with a median prescribed dose of 60 Gy. Results. Overall survival was worse in patients with residual metabolic active areas compared with the patients with a complete metabolic response (p=0.0001). In univariate analysis, three variables were significantly associated with residual disease: larger primary gross tumor volume (GTVprimary, p=0.002), higher pre-treatment maximum standardized uptake value (SUV max , p=0.0005) in the primary tumor and shorter overall treatment time (OTT, p=0.046). A multivariate model including GTVprimary, SUV max , equivalent radiation dose at 2 Gy corrected for time (EQD2, T) and OTT yielded an area under the curve assessed by the leave-one-out cross validation of 0.71 (95% CI, 0.65-0.76). Conclusion. Our results confirmed the validity of metabolic response assessment as a surrogate of survival. We developed a multivariate model that is able to identify patients at risk of residual disease. These patients may benefit from

Acid transformation of bauxite residue: Conversion of its alkaline characteristics.

Science.gov (United States)

Kong, Xiangfeng; Li, Meng; Xue, Shengguo; Hartley, William; Chen, Chengrong; Wu, Chuan; Li, Xiaofei; Li, Yiwei

2017-02-15

Bauxite residue (BR) is a highly alkaline solid hazardous waste produced from bauxite processing for alumina production. Alkaline transformation appears to reduce the environmental risk of bauxite residue disposal areas (BRDAs) whilst potentially providing opportunities for the sustainable reuse and on-going management of BR. Mineral acids, a novel citric acid and a hybrid combination of acid-gypsum treatments were investigated for their potential to reduce residue pH and total alkalinity and transform the alkaline mineral phase. XRD results revealed that with the exception of andradite, the primary alkaline solid phases of cancrinite, grossular and calcite were transformed into discriminative products based on the transformation used. Supernatants separated from BR and transformed bauxite residue (TBR) displayed distinct changes in soluble Na, Ca and Al, and a reduction in pH and total alkalinity. SEM images suggest that mineral acid transformations promote macro-aggregate formation, and the positive promotion of citric acid, confirming the removal or reduction in soluble and exchangeable Na. NEXAFS analysis of Na K-edge revealed that the chemical speciation of Na in TBRs was consistent with BR. Three acid treatments and gypsum combination had no effect on Na speciation, which affects the distribution of Na revealed by sodium STXM imaging. Copyright © 2016 Elsevier B.V. All rights reserved.

Effect of heat treatment duration on phase separation of sodium borosilicate glass, containing copper

International Nuclear Information System (INIS)

Shejnina, T.G.; Gutner, S.Kh.; Anan'in, N.I.

1989-01-01

The effect of heat treatment duration on phase separation of sodium borosilicate (SBS) glass, containing copper is studied. It is stated that phase separation close to equilibrium one is attained under 12 hours of heat treatment of SBS glass containing copper

Alternatives of Treatment and Final Disposition of the Solid Hospital residuals

International Nuclear Information System (INIS)

Meza Monge, K.

1998-01-01

The current handling, treatment and final disposition of the hospital solid waste in Costa Rica are considered inadequate or at least insufficient. This situation represents a serious danger for the population's health and the environment, because they are exposed to infectious agents, toxic substances and even radioactive products that are generated among the residuals of the centers of health. This work, alternatives propose for the treatment and adequate final disposition of the solid waste produced in the hospitals of the country. They take into consideration the characteristics that present these residuals, the advantages and disadvantages of each one of the existent techniques and the technical and economic possibilities of the country. For this purpose, in first instance, a revision about the properties, the quality and the quantity of the solid waste produced by the national hospital centers was carried out. Also, a diagnostic of the current situation of the treatment and final disposition of these residuals in some of the most important hospitals of the country, as well as of the possibilities of physical space with that they count on was carried out. Then, the existent different treatment techniques and final disposition for the solid waste that comes from the centers of health are described, as well as their advantages and disadvantages and a comparative analysis of the same ones is carried out. The objective is completed, since alternatives of treatment and final disposition that are considered appropriate for this type of residuals are planned. Nevertheless, in the future, more detailed investigations and studies of feasibility, with the purpose of developing handling programs and elimination of the solid waste for each one of the hospital centers in Costa Rica should be carried out. (Author) [es

Components inspection of Monju, a sodium bonded type control rod

International Nuclear Information System (INIS)

Harada, Kiyoshi; Matsushita, Yuichi; Lee, Chunchan; Abe, Hideaki; Watahiki, Naohisa

2002-03-01

This Report addresses a result of a sodium test conducted on components of a Double Poral Filter Sodium Bonded Type Control Rod that is expected to be a next generation, long life Control Rod. Upper and lower Poral Filter Sodium Bonded Type Control Rod components were mocked up to conduct a sodium test. During the test, sodium chargeability, formation of Gas Plenum at the upper part of the components, sodium drain-ability and NaOH clean-ability were recognized under actual plant condition. The following are results obtained: (1) Sodium Chargeability at Control Rod Insertion to EVST. Sodium was charged into the components when the mocked-up was inserted in sodium of 190degC, with insertion speed of 6 m/min which is an actual insertion speed to EVST. (2) Formation of Upper Gas Plenum by Helium Gas generated in Control Rod Components Gas Plenum formation within deviation of 9% was confirmed by releasing helium gas into the mocked-up which is immersed in sodium of 620degC and 190degC. Length of Gas Plenum is confirmed to be retained in certain length even if helium gas is further released into formed Gas Plenum. (3) Sodium Drain-ability of Control Rod Components when Drawing from EVST. Drain-ability was confirmed to be sufficient and no sodium residue was found in the mocked-up when the mocked-up was drawn out from sodium of 190degC, with drawing speed of 6 m/min which is an actual drawing speed from EVST. (4) Clean-ability of NaOH Solution against Sodium Residue in Control Rod Components. Sodium and NaOH solution reacted calmly, however, clean-ability was not sufficient. When Sodium fully remained in Control Rod Components, it made circulation of NaOH solution not enough. (author)

Treatment of cows with parturient paresis using intravenous calcium and oral sodium phosphate.

Science.gov (United States)

Braun, U; Grob, D; Hässig, M

2016-09-01

The goal of this study was to investigate whether intravenous infusion of 1000 ml 40% calcium borogluconate combined with the oral adminstration of 500 g sodium phosphate leads to a better cure rate and longer-lasting normocalcaemia and normophosphataemia than standard intravenous treatment with 500 ml calcium borogluconate in cows with parturient paresis. Forty recumbent cows with hypocalcaemia and hypophosphataemia were alternately allocated to group A or B. Cows of both groups were treated intravenously with 500 ml 40% calcium borogluconate, and cows of group B additionally received another 500 ml calcium borogluconate via slow intravenous infusion and 500 g sodium phosphate administered via an orogastric tube. Thirty-two cows stood within 8 hours after the start of treatment and 8 did not; of the 32 cows that stood, 18 belonged to group A and 14 to group B (90% of group A vs. 70% of group B; P = 0.23). Seven cows relapsed; of these and the 8 that did not respond to initial treatment, 10 stood after two standard intravenous treatments. Downer cow syndrome occurred in 5 cows, 3 of which recovered after aggressive therapy. The overall cure rate did not differ significantly between groups A and B. Twelve (60%) cows of group A and 14 (70%) cows of group B were cured after a single treatment and of the remaining 14, 11 were cured after two or more treatments. Two downer cows were euthanized and one other died of heart failure during treatment. Serum calcium concentrations during the first eight hours after the start of treatment were significantly higher in group B than in group A, and oral sodium phosphate caused a significant and lasting increase in inorganic phosphate. More cows of group B than group A were cured after a single treatment (P > 0.05). These findings, although not statistically significant, are promising and should be verified using a larger number of cows.

Gas composition of sludge residue profiles in a sludge treatment reed bed between loadings

DEFF Research Database (Denmark)

Larsen, Julie Dam; Nielsen, Steen M; Scheutz, Charlotte

2017-01-01

Treatment of sludge in sludge treatment reed bed systems includes dewatering and mineralization. The mineralization process, which is driven by microorganisms, produces different gas species as by-products. The pore space composition of the gas species provides useful information on the biological...... processes occurring in the sludge residue. In this study, we measured the change in composition of gas species in the pore space at different depth levels in vertical sludge residue profiles during a resting period of 32 days. The gas composition of the pore space in the sludge residue changed during...

Progress in the development and application of methods for cleaning and decontamination of components exposed to sodium

International Nuclear Information System (INIS)

Msika, D.; Lafon, A.

1978-01-01

In the technology of liquid sodium cooled fast reactors, the necessary processes for washing and decontamination have been demonstrated. For sodium removal, different solutions have been considered and tested in France. The studies have been progressively oriented toward defining a process using a fine dispersion of water in a gas (atomization). The results obtained by that method on non-radioactive components were satisfactory insofar as the efficiency and safety of the operation was concerned. The purpose of decontaminating components from the reactor primary circuits is to reduce the level of surface activity to a level compatible with personnel access without biological shielding. The treatment Is comprised of two stages: (i) washing, to remove any residual sodium, and (ii) decontamination which alternately applies alkaline and acid solutions, to dissolve the deposited radionuclides without significant attack on the surface. The treatment, recently applied to components from in-service reactors, generally met the design objective. (author)

A Patient with MSUD: Acute Management with Sodium Phenylacetate/Sodium Benzoate and Sodium Phenylbutyrate.

Science.gov (United States)

Köse, Melis; Canda, Ebru; Kagnici, Mehtap; Uçar, Sema Kalkan; Çoker, Mahmut

2017-01-01

In treatment of metabolic imbalances caused by maple syrup urine disease (MSUD), peritoneal dialysis, and hemofiltration, pharmacological treatments for elimination of toxic metabolites can be used in addition to basic dietary modifications. Therapy with sodium phenylacetate/benzoate or sodium phenylbutyrate (NaPB) in urea-cycle disorder cases has been associated with a reduction in branched-chain amino acid (BCAA) concentrations when the patients are on adequate dietary protein intake. Moreover, NaPB in treatment of MSUD patients is also associated with reduction of BCAA levels in a limited number of cases. However, there are not enough studies in the literature about application and efficacy of this treatment. Our case report sets an example of an alternative treatment's efficacy when extracorporeal procedures are not available due to technical difficulties during attack period of the disease.

The use of sodium carbonate to improve curing treatments against green and blue moulds on citrus fruits.

Science.gov (United States)

Plaza, Pilar; Usall, Josep; Torres, Rosario; Abadias, Maribel; Smilanick, Joseph L; Viñas, Immaculada

2004-08-01

The effectiveness of curing oranges and lemons at 33 degrees C for 65h followed by storage under ambient and cold-storage conditions was investigated. This treatment effectively reduced the incidence of Penicillium digitatum (Pers) Sacc and P italicum Wehmer decay on inoculated and naturally infected oranges and lemons stored at 20 degrees C for 7 days. However, it failed to control green and blue mould infections on fruits placed in long-term cold storage, except green mould on oranges, which was effectively controlled. Dipping fruits in a sodium carbonate solution (20 g litre(-1)) for 2.5 min following a curing treatment at 33 degrees C for 65 h satisfactorily reduced green and blue mould incidence during subsequent long-term storage at 4 degrees C on oranges and at 10 degrees C on lemons. The efficacy was greater on injured fruits inoculated after the combination of treatments was applied, achieving a 60-80% reduction in decay in comparison with the curing treatment alone in all cases. A significant reduction of blue mould was also observed on fruits inoculated both before the treatments and on those re-inoculated after the treatments, demonstrating both protectant and eradicant activity. Thus, combining curing at 33 degrees C for 65 h with sodium carbonate treatment effectively controlled these post-harvest diseases on artificially inoculated citrus fruits and protected against re-infection. With naturally inoculated lemons, curing followed by sodium carbonate significantly reduced both green and blue mould incidence, but was not superior to curing alone. With naturally infected oranges, curing significantly reduced blue mould, but decay was not reduced further when followed by sodium carbonate treatment.

40 CFR 180.130 - Hydrogen Cyanide; tolerances for residues.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Hydrogen Cyanide; tolerances for... § 180.130 Hydrogen Cyanide; tolerances for residues. (a) General. A tolerance for residues of the insecticide hydrogen cyanide from postharvest fumigation as a result of application of sodium cyanide is...

Fluoroscopically-guided foam sclerotherapy with sodium morrhuate for the treatment of lower extremity varices

International Nuclear Information System (INIS)

Wang Haiting; Jiang Zhongpu; Zhou Yi

2011-01-01

Objective: To evaluate fluoroscopically-guided foam sclerotherapy with injection of domestic sodium morrhuate in treating lower extremity varices. Methods: A total of 30 cases (39 diseased lower limbs) with lower extremity varices were enrolled in this study. Under fluoroscopic guidance foam sclerotherapy with injection of domestic sodium morrhuate was carried out in all patients. The obstructed condition of the great saphenous vein was observed during the following three months. Results: The technical success was achieved in all 39 patients. The mean dose of foam sclerosant used for each diseased limb was 5.9 ml (3.4-8.2 ml). Disappearance of blood flow reflux in lower extremity vein immediately after the treatment was seen in 35 patients (90%). Three months after the therapy, vascular sonography showed that the great saphenous vein was obstructed, and no serious complications occurred. Conclusion: For the treatment of lower extremity varices, fluoroscopically-guided foam sclerotherapy with injection of domestic sodium morrhuate is safe and effective with satisfactory results. This technique is a newly-developed micro-invasive therapy for lower extremity varices. (authors)

A novel cryogenic treatment for reduction of residual stresses in 2024 aluminum alloy

Energy Technology Data Exchange (ETDEWEB)

Araghchi, M., E-mail: M.Araghchi@ma.iut.ac.ir [Department of Materials Engineering, Malek Ashtar University of Technology, Isfahan (Iran, Islamic Republic of); Mansouri, H.; Vafaei, R. [Department of Materials Engineering, Malek Ashtar University of Technology, Isfahan (Iran, Islamic Republic of); Guo, Yina [Bernal Institute, University of Limerick, Limerick (Ireland)

2017-03-24

Residual stresses induced during quenching of aluminum alloys cause distortion and have a negative effect on their properties. The purpose of this study is to reduce the residual stresses and improve mechanical properties by using a novel cryogenic treatment. Water quenched samples were cooled down by immersion in liquid nitrogen at −196 °C, following by rapid heating in hot oil at 180 °C and finally they were artificially aged. Residual stresses was measured by the hole drilling strain gauge method. The mechanical properties and microstructure of a heat treated samples were investigated by means of hardness measurements, tensile tests and transmission electron microscopy. The results showed that this treatment can relieve up to 71% of the residual stresses compared to 29% related to the traditional cryogenic treatment that used boiling water as the reheating medium. In addition, there is a considerable increase of about 75 MPa in the ultimate tensile strength in comparison to the T6 heat-treated alloy. TEM observations revealed that the S′ precipitates were fine and uniformly distributed in the microstructure due to deformation during reheating in hot oil.

Use of Interface Treatment to Reduce Emissions from Residuals in Lower Permeability Zones to Groundwater flowing Through More Permeable Zones (Invited)

Science.gov (United States)

Johnson, P.; Cavanagh, B.; Clifton, L.; Daniels, E.; Dahlen, P.

2013-12-01

Many soil and groundwater remediation technologies rely on fluid flow for contaminant extraction or reactant delivery (e.g., soil vapor extraction, pump and treat, in situ chemical oxidation, air sparging, enhanced bioremediation). Given that most unconsolidated and consolidated settings have permeability contrasts, the outcome is often preferential treatment of more permeable zones and ineffective treatment of the lower permeability zones. When this happens, post-treatment contaminant emissions from low permeability zone residuals can cause unacceptable long-term impacts to groundwater in the transmissive zones. As complete remediation of the impacted lower permeability zones may not be practicable with conventional technologies, one might explore options that lead to reduction of the contaminant emissions to acceptable levels, rather than full remediation of the lower permeability layers. This could be accomplished either by creating a sustained emission reaction/attenuation zone at the high-low permeability interface, or by creating a clean soil zone extending sufficiently far into the lower permeability layer to cause the necessary reduction in contaminant concentration gradient and diffusive emission. These options are explored in proof-of-concept laboratory-scale physical model experiments. The physical models are prepared with two layers of contrasting permeability and either dissolved matrix storage or nonaqueous phase liquid (NAPL) in the lower permeability layer. A dissolved oxidant is then delivered to the interface via flow across the higher permeability layer and changes in contaminant emissions from the low permeability zone are monitored before, during, and after oxidant delivery. The use of three oxidants (dissolved oxygen, hydrogen peroxide and sodium persulfate) for treatment of emissions from petroleum hydrocarbon residuals is examined.

[Sodium intake during pregnancy].

Science.gov (United States)

Delemarre, F M; Franx, A; Knuist, M; Steegers, E A

1999-10-23

International studies have yielded contradictory results on efficacy of a sodium-restricted diet during pregnancy in preventing and curing hypertension of pregnancy. In the Netherlands three studies have been performed to investigate the value of dietary sodium restriction in pregnancy; they concerned epidemiology, prevention and treatment. Midwives often prescribed this dietary intervention. Urinary sodium excretion was not related to blood pressure changes in pregnancy. Dietary sodium restriction from the third month of pregnancy onwards did not reduce the incidence of pregnancy-induced hypertension. Maternal side effects were a decreased intake of nutrients, decreased maternal weight gain, lowered plasma volume and stimulation of the renin-angiotensin-aldosterone system. A dietary sodium restriction in women with early symptoms of pregnancy-induced hypertension showed no therapeutic effect on blood pressure. There is no place for dietary sodium restriction in the prevention or treatment of hypertension in pregnancy.

Gewichtsverlies, serumnatriumconcentratie en restverschijnselen bij patiëntjes met hypertone dehydratie door onvoldoende borstvoeding [Weight loss, serum sodium concentration and residual symptoms in patients with hypernatremic dehydration caused by insufficient breastfeeding

NARCIS (Netherlands)

Breuning-Boers, J.M.; Dommelen, P. van; Wouwe, J.P. van; Verkerk, P.H.

2006-01-01

Objective. To determine the relationship between serum sodium concentration and weight loss as well as residual symptoms in newborns with hypernatremic dehydration caused by insufficient breastfeeding; and to determine the sensitivity of the following rule of thumb 'if weight loss is less than 10%,

Transformation of sodium from the Rapsodie fast breeder reactor into sodium hydroxide

International Nuclear Information System (INIS)

Roger, J.; Latge, C.; Rodriguez, G.

1994-01-01

One of the major problems raised by decommissioning a fast breeder reactor (FBR) concerns the disposal of the sodium coolant. The Desora operation was undertaken to eliminate the Rapsodie primary sodium as part of the partial decommissioning program, and to develop an operational sodium treatment unit for other needs. The process involves reacting small quantities of sodium in water inside a closed vessel, producing aqueous sodium hydroxide and hydrogen gas. It is described in this work. (O.L.). 4 figs

40 CFR 180.1234 - Sodium carbonate; exemption from the requirement of a tolerance.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Sodium carbonate; exemption from the... Exemptions From Tolerances § 180.1234 Sodium carbonate; exemption from the requirement of a tolerance. An exemption from the requirement of a tolerance is established for residues of sodium carbonate. [70 FR 33363...

Study of treatment of a thorium and rare earths residue by extraction chromatography

International Nuclear Information System (INIS)

Zini, Josiane; Abrao, Alcidio; Carvalho, Fatima Maria Sequeira de; Freitas, Antonio Alves de; Scapin, Marcos Antonio

2005-01-01

In the 70's was established at IPEN the project of a thorium compounds purification pilot plant that had the goal of fulfilling the nuclear technology purity standards. The used method was the purification by extraction with solvents in pulsed columns. The thorium remaining in the organic phase was back extracted as thorium nitrate with a high degree of purity. Impurities, thorium non-extracted and practically all rare earths in aqueous phase of this chemical process were precipitated as hydroxide, generating a product containing thorium and rare earths, that was denominated RETOTER (residue of thorium and rare earths). This residue was accumulated and today there are 25 (twenty-five) metric tons of this by product stored in the safeguard storage shed at IPEN that must to be treated due to the radiation of the thorium and mainly his daughters. The average composition of this residue is, 68% in thorium oxide (ThO 2 ), 5% in rare earths oxides (R 2 O 3 ), 0,3% in uranium oxide (U 3 O 8 ) and common impurities such as phosphorus, iron, titanium, lead and sodium. In this work a new method is presented for separation and purification of thorium from this residue, obtaining a concentrate with high degree of purity for nuclear and non-nuclear use. This process will contribute to establish a decreasing of residue volumes, to have a mind to the minimization of environmental impacts, the reduction of worker's exposition and reduction of the storage costs. In this process the separation and purification of uranium and thorium is done by chromatography extraction, being used polymeric resins, that are previously functionalized with organic solvent (extractor agent). The effluent of this process is a concentrate of rare earths that can be reprocessed in a subsequent fractionating for to obtaining the individual fractions. (author)

Prevalence and spectrum of residual symptoms in Lyme neuroborreliosis after pharmacological treatment: a systematic review.

Science.gov (United States)

Dersch, R; Sommer, H; Rauer, S; Meerpohl, J J

2016-01-01

Controversy exists about residual symptoms after pharmacological treatment of Lyme neuroborreliosis. Reports of disabling long-term sequels lead to concerns in patients and health care providers. We systematically reviewed the available evidence from studies reporting treatment of Lyme neuroborreliosis to assess the prevalence and spectrum of residual symptoms after treatment. A literature search was performed in three databases and three clinical trial registers to find eligible studies reporting on residual symptoms in patients after pharmacological treatment of LNB. Diagnosis must have been performed according to consensus-derived case definitions. No restrictions regarding study design or language were set. Symptom prevalence was pooled using a random-effects model. Forty-four eligible clinical trials and studies were found: 8 RCTs, 17 cohort studies, 2 case-control studies, and 17 case series. The follow-up period in the eligible studies ranged from 7 days to 20 years. The weighted mean proportion of residual symptoms was 28 % (95 % CI 23-34 %, n = 34 studies) for the latest reported time point. Prevalence of residual symptoms was statistically significantly higher in studies using the "possible" case definition (p = 0.0048). Cranial neuropathy, pain, paresis, cognitive disturbances, headache, and fatigue were statistically significantly lower in studies using the "probable/definite" case definition. LNB patients may experience residual symptoms after treatment with a prevalence of approximately 28 %. The prevalence and spectrum of residual symptoms differ according to the applied case definition. Symptoms like fatigue are not reported in studies using the "probable/definite" case definition. As the "possible" case definition is more unspecific, patients with other conditions may be included. Reports of debilitating fatigue and cognitive impairment after LNB, a "post-Lyme syndrome", could therefore be an artifact of unspecific case definitions in single

Stabilization of arsenic and chromium polluted soils using water treatment residues

DEFF Research Database (Denmark)

Nielsen, Sanne Skov

water and can be used as a soil amendment to decrease the mobility of CCA in contaminated soil. Stabilization with Fe-WTR was tested at the Collstrop site in Hillerød, Denmark. The site has been polluted with a wide range of wood impregnation agents including CCA during 40 years of wood impregnating...... of contaminants. Arsenic, chromium and copper cannot be degraded and existing methods for cleaning the soil are rarely used as they are expensive and technically demanding. Chemical stabilization of polluted soil is an alternative method for soil remediation, especially metal contamination, and consists in adding...... or other sorbents. Iron water treatment residues mainly consist of ferrihydrite, an oxidized iron oxy-hydroxide with a high reactivity and a large specific surface area with a high capacity for adsorption. Iron water treatment residues (Fe-WTR) are a by-product from treatment of groundwater to drinking...

Effects of gamma irradiation and sodium hydroxide of cell wall constituents and digestibility energy of some agricultural residues. Final report

International Nuclear Information System (INIS)

Al-Masri, M.R.

1996-06-01

The effect of various doses of gamma irradiation (0,100,150,200 KGy) and different concentrations of sodium hydroxide on crude fibre (CF), Cell-wall constituents (NDF, ADF, ADL), in vitro organic matter digestibility (IVOMD), gross energy (GE), in vitro digestible energy (IVDE) of wheat straw (W.S) cotton seed shall (C.S.S), peanut shell (P.S), soybean shell (SB.S), extracted olive cake (O.C.E) and extracted sunflower of unpeeled seeds (S.U.E) were investigated. Results indicated that HaOH in the concentrations at (4 and 6%) had significant effects on the CF content of W.S and P.S, E.U.E, SB.S, C.S.S, O.C.E; respectively. Treating S.U.E, W.S and all other residues with NaoH (2,4 and 6%) respectively, decreased the NDF level. Irradiation dose of 200 KGy decreased CF for all residues, and it reduced the NDF for S.U.E and SB.S. However, lower irradiation dose (150 KGy) was good enough to reduce the NDF for W.S, C.S.S, P.S and O.C.E. Combined treatment resulted in better effects in reducing the concentrations of the cell-wall constituents. The digestible energy values (kJ/Kg DM) increased by 1120,1 220, 2110 (W.S); 620, 830, 1000 for P.S; 240, 500, 580 for O.C.E; 500, 850, 870 for S.U.E; 550, 1060, 1200 for SB.S and 1260, 1710, 2070 for C.S.S using 100, 150, 200, KGy respectively, in comparison to unirradiated controls. Also, the IVDE values (Kj/Kg DM) increased by 560, 1050, 1590 for W.S; 310, 460, 650 for P.S; 170, 760, 1530 for C.S.S; 450, 990, 1190 for O.C.E using 2%, 4%, 6% NaOH respectively, in comparison to controls. No changes in the IVDE values for S.U.E and SB.S. Combined treatment resulted in an even better increase in the digestible energy, except S.U.E and SB.S. (Author). 37 refs., 22 tabs., 18 figs

Successful treatment of sodium oxalate induced urolithiasis with Helichrysum flowers.

Science.gov (United States)

Onaran, Metin; Orhan, Nilüfer; Farahvash, Amirali; Ekin, Hasya Nazlı; Kocabıyık, Murat; Gönül, İpek Işık; Şen, İlker; Aslan, Mustafa

2016-06-20

Helichrysum (Asteraceae) flowers, known as "altın otu, yayla çiçeği, kudama çiçeği" , are widely used to remove kidney stones and for their diuretic properties in Turkey. To determine the curative effect of infusions prepared from capitulums of Helichrysum graveolens (M. Bieb.) Sweet (HG) and H. stoechas ssp. barellieri (Ten.) Nyman (HS) on sodium oxalate induced kidney stones. Infusions prepared from the capitulums of HG and HS were tested for their curative effect on calcium oxalate deposition induced by sodium oxalate (70mg/kg i.p.). Following the injection of sodium oxalate for 5 days, plant extracts were administered to rats at two different doses. Potassium citrate was used as positive control. Water intake, urine volume, body, liver and kidney weights were measured; biochemical and hematological analyses were conducted on urine and blood samples. Additionally, histopathological examinations were done on kidney samples. H. stoechas extract showed prominent effect at 156mg/kg dose (stone formation score: 0.33), whereas number of kidney stones was maximum in sodium oxalate group (stone formation score: 2.33). The reduction in the uric acid and oxalate levels of urine samples and the elevation in the urine citrate levels are significant and promising in extract groups. Some hematological, biochemical and enzymatic markers are also ameliorated by the extracts. This is the first report on the curative effect of immortal flowers. Our preliminary study indicated that Helichrysum extracts may be used for treatment of urolithiasis and Helichrysum extracts are an alternative therapy to potassium citrate for patients suffering from kidney stones. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Thermal decomposition of nitrate salts liquid waste for the lagoon sludge treatment

International Nuclear Information System (INIS)

Hwang, D. S.; Oh, J. H.; Kim, Y. K.; Lee, K. Y.; Choi, Y. D.; Hwang, S. T.; Park, J. H.

2004-01-01

This study investigated the thermal decomposition property of nitrate salts liquid waste which is produced in a series of the processes for the sludge treatment. Thermal decomposition property was analyzed by TG/DTA and XRD. Most ammonium nitrate in the nitrate salts liquid waste was decomposed at 250 .deg. C and calcium nitrate was decomposed and converted into calcium oxide at 550 .deg. C. Sodium nitrate was decomposed at 700 .deg. C and converted into sodium oxide which reacts with water easily. But sodium oxide was able to convert into a stable compound by adding alumina. Therefore, nitrate salts liquid waste can be treated by two steps as follows. First, ammonium nitrate is decomposed at 250 .deg. C. Second, alumina is added in residual solid sodium nitrate and calcium nitrate and these are decomposed at 900 .deg. C. Final residue consists of calcium oxide and Na 2 O.Al 2 O 3 and can be stored stably

Efficacy Of A Single-Injection Sodium Hyaluronate Treatment In Lateral Epicondylitis.

Science.gov (United States)

Khan, Inam Ullah; Awan, Abdus Saboor; Khan, Aimal Sattar; Marwat, Imran; Meraj, Muhammad

2018-01-01

Lateral epicondylitis or tennis elbow is a disease of tendons arising from common extensor origin at the lateral epicondyle of elbow and is commonly characterized by pain on supination of forearms as well as extension of fingers and wrists. This descriptive case series aims to determine the efficacy of a single-injection sodium hyaluronate treatment for lateral epicondylitis. The study was conducted at the Department of Orthopaedics. Ayub Teaching Hospital Abbottabad. From February 1 to August 31, 2014. Patients diagnosed with lateral epicondylitis were administered 1 cc of 1% Sodium hyaluronate 1 cm from the lateral epicondyle into the soft tissue. Hyaluronic acid is more effective in patients with moderate pain of lateral epicondylitis (VAS score ≤7 than in patients with severe pain (VAS score >7). Paired sample t-test was used to compared the means of the pre- and post-procedure VAS score and the difference was found to be statistically very significant (p=0.00) with a mean±SD change in VAS of 2.31±1.35 at 4 weeks. A single injection of sodium hyaluronate is effective in management of moderate, but not severe pain of lateral epicondylitis.

Green synthesis of graphitic carbon nitride nanodots using sodium chloride template

Energy Technology Data Exchange (ETDEWEB)

Yuan, Bo [National University of Defense Technology, College of Science (China); Zou, Xianshuai; Yan, Tingnan; Fei, Junjie [Xiangtan University, College of Chemistry (China); Chu, Zengyong, E-mail: chuzy@nudt.edu.cn [National University of Defense Technology, College of Science (China)

2016-05-15

Graphitic carbon nitride (g-C{sub 3}N{sub 4}) nanodots are simply prepared by a thermal treatment of dicyandiamide (DCDA) confined within NaCl templates. Cyano groups are introduced to the nanodots due to the catalytic effect of NaCl. NaCl could facilitate the polymerization of DCDA at lower temperatures, but will promote the decomposition when the temperature is above 550 °C. Thermal treatment at 600 °C for 30 min is the optimal condition for the scalable synthesis of g-C{sub 3}N{sub 4} nanodots with an average diameter of ~9 nm. g-C{sub 3}N{sub 4} nanodots have a higher band gap of 3.1 eV, which can emit bright blue light due to the decreased diameter, the introduction of cyano groups, and the incorporation of some sodium ions. The residue sodium ions and the cyano groups might lead to the local distortion of the graphitic crystals, or act as recombination centers for the enhanced photoluminescence.Graphical Abstract.

Residual water treatment for gamma radiation. Tratamiento de aguas residuales por radiacion gamma

Energy Technology Data Exchange (ETDEWEB)

Mendez, L [Universidad Nacional Mayor de San Marcos. Facultad de Quimica (Peru)

1990-07-01

The treatment of residual water by means of gamma radiation for its use in agricultural irrigation is evaluated. Measurements of physical, chemical, biological and microbiological contamination indicators were performed. For that, samples from the treatment center of residual water of San Juan de Miraflores were irradiated up to a 52.5 kGy dose. The study concludes that gamma radiation is effective to remove parasites and bacteria, but not for removal of the organic and inorganic matter. (author). 15 refs., 3 tabs., 4 figs.

Treatment of plutonium process residues by molten salt oxidation

Energy Technology Data Exchange (ETDEWEB)

Stimmel, J.; Wishau, R.; Ramsey, K.B.; Montoya, A.; Brock, J. [Los Alamos National Lab., NM (United States); Heslop, M. [Naval Surface Warfare Center (United States). Indian Head Div.; Wernly, K. [Molten Salt Oxidation Corp. (United States)

1999-04-01

Molten Salt Oxidation (MSO) is a thermal process that can remove more than 99.999% of the organic matrix from combustible {sup 238}Pu material. Plutonium processing residues are injected into a molten salt bed with an excess of air. The salt (sodium carbonate) functions as a catalyst for the conversion of the organic material to carbon dioxide and water. Reactive species such as fluorine, chlorine, bromine, iodine, sulfur, phosphorous and arsenic in the organic waste react with the molten salt to form the corresponding neutralized salts, NaF, NaCl, NaBr, NaI, Na{sub 2}SO{sub 4}, Na{sub 3}PO{sub 4} and NaAsO{sub 2} or Na{sub 3}AsO4. Plutonium and other metals react with the molten salt and air to form metal salts or oxides. Saturated salt will be recycled and aqueous chemical separation will be used to recover the {sup 238}Pu. The Los Alamos National Laboratory system, which is currently in the conceptual design stage, will be scaled down from current systems for use inside a glovebox.

Treatment of plutonium process residues by molten salt oxidation

International Nuclear Information System (INIS)

Stimmel, J.; Wishau, R.; Ramsey, K.B.; Montoya, A.; Brock, J.; Heslop, M.

1999-01-01

Molten Salt Oxidation (MSO) is a thermal process that can remove more than 99.999% of the organic matrix from combustible 238 Pu material. Plutonium processing residues are injected into a molten salt bed with an excess of air. The salt (sodium carbonate) functions as a catalyst for the conversion of the organic material to carbon dioxide and water. Reactive species such as fluorine, chlorine, bromine, iodine, sulfur, phosphorous and arsenic in the organic waste react with the molten salt to form the corresponding neutralized salts, NaF, NaCl, NaBr, NaI, Na 2 SO 4 , Na 3 PO 4 and NaAsO 2 or Na 3 AsO4. Plutonium and other metals react with the molten salt and air to form metal salts or oxides. Saturated salt will be recycled and aqueous chemical separation will be used to recover the 238 Pu. The Los Alamos National Laboratory system, which is currently in the conceptual design stage, will be scaled down from current systems for use inside a glovebox

A Patient with MSUD: Acute Management with Sodium Phenylacetate/Sodium Benzoate and Sodium Phenylbutyrate

Directory of Open Access Journals (Sweden)

Melis Köse

2017-01-01

Full Text Available In treatment of metabolic imbalances caused by maple syrup urine disease (MSUD, peritoneal dialysis, and hemofiltration, pharmacological treatments for elimination of toxic metabolites can be used in addition to basic dietary modifications. Therapy with sodium phenylacetate/benzoate or sodium phenylbutyrate (NaPB in urea-cycle disorder cases has been associated with a reduction in branched-chain amino acid (BCAA concentrations when the patients are on adequate dietary protein intake. Moreover, NaPB in treatment of MSUD patients is also associated with reduction of BCAA levels in a limited number of cases. However, there are not enough studies in the literature about application and efficacy of this treatment. Our case report sets an example of an alternative treatment’s efficacy when extracorporeal procedures are not available due to technical difficulties during attack period of the disease.

The effectiveness of sewage treatment processes to remove faecal pathogens and antibiotic residues

Science.gov (United States)

Hendricks, Rahzia; Pool, Edmund John

2012-01-01

Pathogens and antibiotics enter the aquatic environment via sewage effluents and may pose a health risk to wild life and humans. The aim of this study was to determine the levels of faecal bacteria, and selected antibiotic residues in raw wastewater and treated sewage effluents from three different sewage treatment plants in the Western Cape, South Africa. Sewage treatment plant 1 and 2 use older technologies, while sewage treatment plant 3 has been upgraded and membrane technologies were incorporated in the treatment processes. Coliforms and Escherichia coli (E. coli) were used as bioindicators for faecal bacteria. A chromogenic test was used to screen for coliforms and E. coli. Fluoroquinolones and sulfamethoxazole are commonly used antibiotics and were selected to monitor the efficiency of sewage treatment processes for antibiotic removal. Enzyme Linked Immunosorbent Assays (ELISAs) were used to quantitate antibiotic residues in raw and treated sewage. Raw intake water at all treatment plants contained total coliforms and E. coli. High removal of E. coli by treatment processes was evident for treatment plant 2 and 3 only. Fluoroquinolones and sulfamethoxazole were detected in raw wastewater from all sewage treatment plants. Treatment processes at plant 1 did not reduce the fluoroquinolone concentration in treated sewage effluents. Treatment processes at plant 2 and 3 reduced the fluoroquinolone concentration by 21% and 31%, respectively. Treatment processes at plant 1 did not reduce the sulfamethoxazole concentration in treated sewage effluents. Treatment processes at plant 2 and 3 reduced sulfamethoxazole by 34% and 56%, respectively. This study showed that bacteria and antibiotic residues are still discharged into the environment. Further research needs to be undertaken to improve sewage treatment technologies, thereby producing a better quality treated sewage effluent. PMID:22242882

The Effectiveness of Diclofenac Sodium in the Treatment of Mondor's Disease of the Breast: The Topical Patch Compared to the Oral Capsules.

Science.gov (United States)

Shirah, Bader Hamza; Shirah, Hamza Assad; Alonazie, Wedad Salem

2017-07-01

Mondor's disease of the breast is a rare, benign sclerosing superficial thrombophlebitis of the subcutaneous veins of the anterior or lateral chest wall, which is treated conservatively. We aim in this study to evaluate the outcome and effectiveness of our treatment protocol using oral diclofenac sodium and topical diclofenac sodium patch in 172 patients. A retrospective database analysis of 172 female patients between January 2001 and December 2010 was done. The treatment protocol consisted of group 1: treatment by oral diclofenac sodium 100 mg once daily for 3 weeks. Group 2: treatment by diclofenac sodium patches for 8 hours twice daily (morning and evening) for 1 week. The patients were instructed to document the time as soon as pain relief is achieved following the patch application and the intake of the oral dose. The incidence rate was 2.49%. Diclofenac sodium patch was statistically found to be significantly better in subsiding the inflammatory process of the veins, relieving the pain, and enhancing faster healing rate. We conclude that diclofenac sodium patch showed a promising role in the treatment of Mondor's disease of the breast by significantly decreasing the inflammatory process due to its transdermal migration action within a short period and the ability to reach a high local concentration. It achieved the best results for rapid relief of pain and disease regression compared to the oral capsules. Therefore, our protocol was changed to implement diclofenac sodium patch as the first choice in treating Mondor's disease of the breast. © 2017 Wiley Periodicals, Inc.

Experimental study of the tritium distribution in the effluents resulting from the sodium hydrolysis

Energy Technology Data Exchange (ETDEWEB)

Chassery, A. [CEA, DEN, Centre de Cadarache, Saint-Paul-lez-Durance (France); Universite de Toulouse, Laboratoire de Genie Chimique, Toulouse (France); CNRS, Laboratoire de Genie Chimique, Toulouse (France); Lorcet, H.; Godlewski, J; Liger, K.; Latge, C. [CEA, DEN, Centre de Cadarache, Saint-Paul-lez-Durance (France); Joulia, X. [Universite de Toulouse, Laboratoire de Genie Chimique, Toulouse (France); CNRS, Laboratoire de Genie Chimique, Toulouse (France)

2015-03-15

Within the framework of the dismantling of fast breeder reactors in France several processes are under investigation regarding sodium disposal. One of them, called ELA (radioactive sodium waste treatment process), is based on the implementation of the sodium-water reaction, in a controlled and progressive way, to remove residual sodium. This sodium contains impurities such as sodium hydride, sodium oxide and tritiated sodium hydride. The hydrolysis of these various chemical species leads to the production of a liquid effluent, mainly composed of an aqueous solution of sodium hydroxide, and a gaseous effluent, mainly composed of nitrogen (inert gas), hydrogen and steam. The tritium is distributed between these effluents, and, within the gaseous effluent, according to its forms HT and HTO (tritiated water). HTO being 10,000 times more radio-toxic than HT, a precise knowledge of the mechanisms governing the phase distribution of tritium is necessary. This paper presents the first experimental results from a parametric study on the tritium distribution between the various effluents generated during hydrolysis operations. A series of experiments have been performed in order to study the influence of water flow rate, argon flow rate, initial mass and specific activity of the hydrolyzed sodium sample. An important influence of the total tritium concentration in the hydrolyzed sample has been highlighted. As for the phenomena suspected to be responsible for the phase change of tritiated water, in the studied range of parameters, vaporization induced by the heat of reactions seems to be dominant over the evaporation induced by the inert gas flow rate.

Extraction of toxic and valuable metals from wastewater sludge and ash arising from RECICLAGUA, a treatment plant for residual waters applying the leaching technique

International Nuclear Information System (INIS)

Guerrero D, J.J.

2004-01-01

Presently work, the technique is applied of having leached using coupled thermostatted columns, the X-ray diffraction for the identification of the atomic and molecular structure of the metals toxic that are present in the residual muds of a treatment plant of water located in the municipality of the Estado de Mexico, RECICLAGUA, likewise the techniques is used of Inductively Coupled Plasma Mass Spectroscopy and X-ray fluorescence analysis for the qualitative analysis. We took samples of residual sludge and incinerated ash of a treatment plant waste water from the industrial corridor Toluca-Lerma RECICLAGUA, located in Lerma, Estado de Mexico. For this study 100 g. of residual of sludge mixed with a solution to 10% of mineral acid or sodium hydroxide according to the case, to adjust the one p H at 2, 5, 7 and 10, bisulfite was added, of 0.3-1.5 g of dodecyl sulfate of sodium and 3.93 g of DTPA (triple V). Diethylene triamine penta acetate. These sludges and ashes were extracted from toxic and valuable metals by means of the leaching technique using coupled thermostated columns that which were designed by Dr. Jaime Vite Torres, it is necessary to make mention that so much the process as the apparatus with those that one worked was patented by him same. With the extraction of these metals, benefits are obtained, mainly of economic type, achieving the decrease of the volume of those wastes that have been generated; as well as the so much use of those residuals, once the metals have been eliminated, as of those residuals, once the metals have been eliminated, as of those liquors, the heavy metals were extracted. It was carried out a quantitative analysis using Icp mass spectroscopy, this way to be able to know the one content of the present metals in the samples before and after of leaching them, these results reported a great quantity of elements. Another of the techniques employees was the analysis by X-ray diffraction that provides an elementary content of the

Is addition of sodium fluoride to cyclical etidronate beneficial in the treatment of corticosteroid induced osteoporosis?

NARCIS (Netherlands)

Lems, W. F.; Jacobs, J. W.; Bijlsma, J. W.; van Veen, G. J.; Houben, H. H.; Haanen, H. C.; Gerrits, M. I.; van Rijn, H. J.

1997-01-01

To investigate whether administration of sodium fluoride (NaF) in addition to cyclical etidronate has a positive effect on bone mineral density (BMD) in patients with established osteoporosis during continued treatment with corticosteroids. 47 patients who were receiving treatment with

Treatment of waste incinerator air-pollution-control residues with FeSO4: Concept and product characterization

DEFF Research Database (Denmark)

Lundtorp, Kasper; Jensen, Dorthe Lærke; Sørensen, Mette Abildgaard

2002-01-01

This paper describes a new concept for treatment of air- pollution-control (APC) residues from waste incineration and characterises the wastewater and stabilised residues generated by the process. The process involves mixing of APC-residues with a ferrous sulphate solution and subsequent oxidation...

Two-dimensional 1H NMR experiments show that the 23-residue magain in antibiotic peptide is an α-helix in dodecylphosphocholine micelles, sodium dodecylsulfate micelles, and trifluoroethanol/water solution

International Nuclear Information System (INIS)

Gesell, Jennifer; Zasloff, Michael; Opella, Stanley J.

1997-01-01

Magainin2 is a 23-residue antibiotic peptide that disrupts the ionic gradient across certain cell membranes. Two-dimensional 1H NMR spectroscopy was used to investigate the structure of the peptide in three of the membrane environments most commonly employed in biophysical studies. Sequence-specific resonance assignments were determined for the peptide in perdeuterated dodecylphosphocholine (DPC) and sodium dodecylsulfate micelles and confirmed for the peptide in 2,2,2-trifluoroethanol solution. The secondary structure is shown to be helical in all of the solvent systems. The NMR data were used as a set of restraints for a simulated annealing protocol that generated a family of three-dimensional structures of the peptide in DPC micelles, which superimposed best between residues 4 and 20. For these residues, the mean pairwise rms difference for the backbone atoms is 0.47 ± 0.10A from the average structure. The calculated peptide structures appear to be curved,with the bend centered at residues Phe12 and Gly13

French research on a general approach to sodium fires

International Nuclear Information System (INIS)

Malet, JC.

1989-01-01

This document gives a general idea of how one may deal with the safety of an installation in case of a sodium leak generating either a sodium pool fire, or a sodium spray fire, or a combined sodium fire, and in case of a sodium leak either with or without fire and/or any aggravating phenomenon such as aerosols or sodium-concrete reactions, for example. This paper describes the means used to reduce fire consequences. These means are either design codes used for dimensioning premises with their ventilation system or for defining a course of action to be taken in case of fire, or equipment and components (fire fighting equipment, detection devices, etc.) used to prevent or to fight fires, or finally, to repair the installation after a fire, the latter operation including the processing of the residues. (author)

Topical Colchicine Gel versus Diclofenac Sodium Gel for the Treatment of Actinic Keratoses: A Randomized, Double-Blind Study.

Science.gov (United States)

Faghihi, Gita; Elahipoor, Azam; Iraji, Fariba; Behfar, Shadi; Abtahi-Naeini, Bahareh

2016-01-01

Introduction. Actinic keratoses (AKs), a premalignant skin lesion, are a common lesion in fair skin. Although destructive treatment remains the gold standard for AKs, medical therapies may be preferable due to the comfort and reliability .This study aims to compare the effects of topical 1% colchicine gel and 3% diclofenac sodium gel in AKs. Materials and Methods. In this randomized double-blind study, 70 lesions were selected. Patients were randomized before receiving either 1% colchicine gel or 3% diclofenac sodium cream twice a day for 6 weeks. Patients were evaluated in terms of their lesion size, treatment complications, and recurrence at 7, 30, 60, and 120 days after treatment. Results. The mean of changes in the size was significant in both groups both before and after treatment ( 0.05). No case of erythema was seen in the colchicine group, while erythema was seen in 22.9% (eight cases) of patients in the diclofenac sodium group (p = 0.005). Conclusions. 1% colchicine gel was a safe and effective medication with fewer side effects and lack of recurrence of the lesion.

Topical Colchicine Gel versus Diclofenac Sodium Gel for the Treatment of Actinic Keratoses: A Randomized, Double-Blind Study

Directory of Open Access Journals (Sweden)

Gita Faghihi

2016-01-01

Full Text Available Introduction. Actinic keratoses (AKs, a premalignant skin lesion, are a common lesion in fair skin. Although destructive treatment remains the gold standard for AKs, medical therapies may be preferable due to the comfort and reliability .This study aims to compare the effects of topical 1% colchicine gel and 3% diclofenac sodium gel in AKs. Materials and Methods. In this randomized double-blind study, 70 lesions were selected. Patients were randomized before receiving either 1% colchicine gel or 3% diclofenac sodium cream twice a day for 6 weeks. Patients were evaluated in terms of their lesion size, treatment complications, and recurrence at 7, 30, 60, and 120 days after treatment. Results. The mean of changes in the size was significant in both groups both before and after treatment ( 0.05. No case of erythema was seen in the colchicine group, while erythema was seen in 22.9% (eight cases of patients in the diclofenac sodium group (p = 0.005. Conclusions. 1% colchicine gel was a safe and effective medication with fewer side effects and lack of recurrence of the lesion.

Gas composition of sludge residue profiles in a sludge treatment reed bed between loadings.

Science.gov (United States)

Larsen, Julie D; Nielsen, Steen M; Scheutz, Charlotte

2017-11-01

Treatment of sludge in sludge treatment reed bed systems includes dewatering and mineralization. The mineralization process, which is driven by microorganisms, produces different gas species as by-products. The pore space composition of the gas species provides useful information on the biological processes occurring in the sludge residue. In this study, we measured the change in composition of gas species in the pore space at different depth levels in vertical sludge residue profiles during a resting period of 32 days. The gas composition of the pore space in the sludge residue changed during the resting period. As the resting period proceeded, atmospheric air re-entered the pore space at all depth levels. The methane (CH 4 ) concentration was at its highest during the first part of the resting period, and then declined as the sludge residue became more dewatered and thereby aerated. In the pore space, the concentration of CH 4 often exceeded the concentration of carbon dioxide (CO 2 ). However, the total emission of CO 2 from the surface of the sludge residue exceeded the total emission of CH 4 , suggesting that CO 2 was mainly produced in the layer of newly applied sludge and/or that CO 2 was emitted from the sludge residue more readily compared to CH 4 .

Phase 2 THOR Steam Reforming Tests for Sodium Bearing Waste Treatment

Energy Technology Data Exchange (ETDEWEB)

Nicholas R. Soelberg

2004-01-01

About one million gallons of acidic, hazardous, and radioactive sodium-bearing waste is stored in stainless steel tanks at the Idaho Nuclear Technology and Engineering Center (INTEC), which is a major operating facility of the Idaho National Engineering and Environmental Laboratory. Steam reforming is a candidate technology being investigated for converting the waste into a road ready waste form that can be shipped to the Waste Isolation Pilot Plant in New Mexico for interment. A steam reforming technology patented by Studsvik, Inc., and licensed to THOR Treatment Technologies has been tested in two phases using a Department of Energy-owned fluidized bed test system located at the Science Applications International Corporation (SAIC) Science and Technology Applications Research Center located in Idaho Falls, Idaho. The Phase 1 tests were reported earlier in 2003. The Phase 2 tests are reported here. For Phase 2, the process feed rate, stoichiometry, and chemistry were varied to identify and demonstrate process operation and product characteristics under different operating conditions. Two test series were performed. During the first series, the process chemistry was designed to produce a sodium carbonate product. The second series was designed to produce a more leach-resistant, mineralized sodium aluminosilicate product. The tests also demonstrated the performance of a MACT-compliant off-gas system.

Interaction of cadmium and indium nitrate mixture with sodium tungstate in aqueous solution

Energy Technology Data Exchange (ETDEWEB)

Belousova, E E; Krivobok, V I; Gruba, A I [Donetskij Gosudarstvennyj Univ. (Ukrainian SSR)

1982-01-01

The interaction of the mixture of cadmium and indium nitrates with sodium tungstate in aqueous solution is studied using the methods of ''residual concentrations'', pH potentiometry and conductometry. Independent of the ratio of components in the initial solution a mixture of coprecipitated normal tungstates of cadmium and indium is formed in the system. Heat treatment of the precipitates at 800 deg C for 50 hrs with subsequent hardening results in the formation of solid solutions on the basis of normal cadmium and indium tungstates.

Techniques of material-flow-specific residual waste treatment; Techniken der stoffstromspezifischen Restabfallbehandlung

Energy Technology Data Exchange (ETDEWEB)

Maak, D.; Collins, H.J. [Technische Univ. Braunschweig, Leichtweiss - Inst. fuer Wasserbau (Germany)

1998-09-01

The success achieved with large-scale plants for mechanical-biological residual waste treatment has led to a change of course in waste pretreatment. In view of the low emissions via the water and gas routes from landfilled wastes and the low costs of waste treatment some authorising authorities have meanwhile issued special licences pursuant to clause no. 2.4 of the Technical Code on Household Waste, thus enabling mechanical-biological residual waste treatment plants to continue operations beyond the year 2005. Beside offering a means of treatment and disposal, cost-effective mechanical-biological pretreatment also provides an opportunity for going over to material-flow-specific residual waste treatment. These process stages permit recirculating valuable materials and using other materials for energy production. They can be retrofitted on a modular basis in existing plants. If these advantages of the present innovative pretreatment methods are not used, then mechanical-biological pretreatment can still serve as a preparatory stage for thermal treatment. To date there has been no practical experience with this innovative method of residual waste treatment. However, industrial-scale trials have shown that each individual treatment stage is capable of being carried out successfully. [Deutsch] Die guten Erfolge im grosstechnischen Betrieb von Anlagen zur mechanisch-biologischen Restabfallbehandlung haben zu einer Kursaenderung bei der Vorbehandlung von Abfaellen gefuehrt. Geringe Emissionen der deponierten Abfaelle auf dem Gas- und Wasserpfad sowie geringe Kosten fuer die Behandlung der Abfaelle haben dazu gefuehrt, dass inzwischen bereits einige Genehmigungsbehoerden eine Ausnahmegenehmigung nach Nr. 2.4 der TA Siedlungsabfall erteilt haben und damit der Betrieb von mechanisch-biologischen Restabfallbehandlungsanlagen auch nach 2005 ermoeglicht wird. Neben der alleinigen Behandlung und Deponierung bietet die kostenguenstige Vorbehandlung mit mechanisch

Conversion of rice hull ash into soluble sodium silicate

Directory of Open Access Journals (Sweden)

Edson Luiz Foletto

2006-09-01

Full Text Available Sodium silicate is used as raw material for several purposes: silica gel production, preparation of catalysts, inks, load for medicines, concrete hardening accelerator, component of detergents and soaps, refractory constituent and deflocculant in clay slurries. In this work sodium silicate was produced by reacting rice hull ash (RHA and aqueous sodium hydroxide, in open and closed reaction systems. The studied process variables were time, temperature of reaction and composition of the reaction mixture (expressed in terms of molar ratios NaOH/SiO2 and H2O/SiO2. About 90% silica conversion contained in the RHA into sodium silicate was achieved in closed system at 200 °C. The results showed that sodium silicate production from RHA can generate aggregate value to this residue.

The sodium pentothal hypnosis interview with follow-up treatment for complex regional pain syndrome.

Science.gov (United States)

Simon, E P; Dahl, L F

1999-08-01

A patient who was unresponsive to multiple conservative medical treatments for complex regional pain syndrome was assessed using a novel approach--the sodium pentothal hypnosis interview. The interview suggested that his pain was centrally generated. The patient's pain symptoms resolved with hypnotherapeutic treatment. Indications for this procedure and implications for assessment and treatment are discussed. This case raises more questions than it answers, and leaves the reader to struggle with current difficulties in diagnostic decision-making.

Use of gypsum residues as a corrective for saline-sodic soil

Directory of Open Access Journals (Sweden)

Paulo Medeiros dos Santos

2014-03-01

Full Text Available One of the hugest problems faced by the civil construction sector is the final destination of residues, especially gypsum, which presents recycling restrictions. However, these residues present a high amount of calcium in their composition, and can be alternatively used for replacing mined gypsum as a saline-sodic soil corrective. This study aimed at evaluating the efficiency of gypsum residues from the civil construction, when compared to mined gypsum, for correcting a saline-sodic soil. A randomized blocks design was used, in a factorial arrangement consisting of two kinds of corrective (gypsum residue and mined gypsum and five leaching depths (0.5, 1.0, 1.5, 2.0 and 2.5 times the soil pores volume, with three replications. Electric conductivity, soluble cations and sodium adsorption ratio were evaluated in the soil saturation extract. The use of gypsum residue proved to be effective in leaching salts and soluble sodium in saline-sodic soil, and can be recommended as a calcium source for recovering from sodicity.

Targeting cysteine residues of human immunodeficiency virus type 1 protease by reactive free radical species.

Science.gov (United States)

Basu, A; Sehajpal, P K; Ogiste, J S; Lander, H M

1999-01-01

Nitric oxide (NO) is a naturally occurring free radical with many functions. The oxidized form of NO, the nitrosonium ion, reacts with the thiol group of cysteine residues resulting in their modification to S-nitrosothiols. The human immunodeficiency virus type 1 (HIV-1) protease (HIV-PR) has two cysteine residues that are conserved amongst different viral isolates found in patients with acquired immunodeficiency syndrome (AIDS). In an active dimer, these residues are located near the surface of the protease. We have found that treatment of HIV-PR with different NO congeners results in loss of its proteolytic activity and simultaneous formation of S-nitrosothiols. Sodium nitroprusside inhibited HIV-PR up to 70% and S-nitroso-N-acetylpenicillamine completely inhibited the protease within 5 min of treatment. The pattern of inhibition by NO donors is comparable to its inhibition by N-acetyl pepstatin. Using electrospray ionization-mass spectrometry, we identified the modification of HIV-PR by NO as that of S-nitrosation. Our findings point towards a possible role of NO in mediating resistance to HIV-1 infection.

Investigation of patient, tumour and treatment variables affecting residual motion for respiratory-gated radiotherapy

International Nuclear Information System (INIS)

George, R; Ramakrishnan, V; Siebers, J V; Chung, T D; Keall, P J

2006-01-01

Respiratory gating can reduce the apparent respiratory motion during imaging and treatment; however, residual motion within the gating window remains. Respiratory training can improve respiratory reproducibility and, therefore, the efficacy of respiratory-gated radiotherapy. This study was conducted to determine whether residual motion during respiratory gating is affected by patient, tumour or treatment characteristics. The specific aims of this study were to: (1) identify significant characteristics affecting residual motion, (2) investigate time trends of residual motion over a period of days (inter-session) and (3) investigate time trends of residual motion within the same day (intra-session). Twenty-four lung cancer patients were enrolled in an Institutional Review Board (IRB)-approved protocol. For approximately five sessions, 331 four-minute, respiratory motion traces were acquired with free breathing, audio instructions and audio-visual biofeedback for each patient. The residual motion was quantified by the standard deviation of the displacement within the gating window. The generalized linear model was used to obtain coefficients for each variable within the model and to evaluate the clinical and statistical significance. The statistical significance was determined by a p-value <0.05, while effect sizes of ≥0.1 cm (one standard deviation) were considered clinically significant. This data analysis was applied to patient, tumour and treatment variables. Inter- and intra-session variations were also investigated. The only variable that was significant for both inhale- and exhale-based gating was disease type. In addition, visual-training displacement, breathing type and Karnofsky performance status (KPS) values were significant for inhale-based gating, and dose-per-fraction was significant for exhale-based gating. Temporal respiratory variations within and between sessions were observed for individual patients. However inter- and intra-session analyses did

Investigation of patient, tumour and treatment variables affecting residual motion for respiratory-gated radiotherapy

Energy Technology Data Exchange (ETDEWEB)

George, R [Department of Radiation Oncology, Virginia Commonwealth University, Richmond, VA (United States); Ramakrishnan, V [Department of Biostatistics, Virginia Commonwealth University, Richmond, VA (United States); Siebers, J V [Department of Radiation Oncology, Virginia Commonwealth University, Richmond, VA (United States); Chung, T D [Department of Radiation Oncology, Virginia Commonwealth University, Richmond, VA (United States); Keall, P J [Department of Radiation Oncology, Virginia Commonwealth University, Richmond, VA (United States)

2006-10-21

Respiratory gating can reduce the apparent respiratory motion during imaging and treatment; however, residual motion within the gating window remains. Respiratory training can improve respiratory reproducibility and, therefore, the efficacy of respiratory-gated radiotherapy. This study was conducted to determine whether residual motion during respiratory gating is affected by patient, tumour or treatment characteristics. The specific aims of this study were to: (1) identify significant characteristics affecting residual motion, (2) investigate time trends of residual motion over a period of days (inter-session) and (3) investigate time trends of residual motion within the same day (intra-session). Twenty-four lung cancer patients were enrolled in an Institutional Review Board (IRB)-approved protocol. For approximately five sessions, 331 four-minute, respiratory motion traces were acquired with free breathing, audio instructions and audio-visual biofeedback for each patient. The residual motion was quantified by the standard deviation of the displacement within the gating window. The generalized linear model was used to obtain coefficients for each variable within the model and to evaluate the clinical and statistical significance. The statistical significance was determined by a p-value <0.05, while effect sizes of {>=}0.1 cm (one standard deviation) were considered clinically significant. This data analysis was applied to patient, tumour and treatment variables. Inter- and intra-session variations were also investigated. The only variable that was significant for both inhale- and exhale-based gating was disease type. In addition, visual-training displacement, breathing type and Karnofsky performance status (KPS) values were significant for inhale-based gating, and dose-per-fraction was significant for exhale-based gating. Temporal respiratory variations within and between sessions were observed for individual patients. However inter- and intra-session analyses did

Some techniques used in the treatment of phenolic waters residual

International Nuclear Information System (INIS)

Alzate S, Rafael A.; Botero, Carlos Andre

2000-01-01

The current state of the diverse processes of treatment of phenolic waters residual is presented, beginning with the methods traditionally employees, until finishing with those but recent innovations, which have been derived of the necessity of increasing the removal of these pollutants without increasing the costs of such processes in excessive form

Theoretical Adiabatic Temperature and Chemical Composition of Sodium Combustion Flame

International Nuclear Information System (INIS)

Okano, Yasushi; Yamaguchi, Akira

2003-01-01

Sodium fire safety analysis requires fundamental combustion properties, e.g., heat of combustion, flame temperature, and composition. We developed the GENESYS code for a theoretical investigation of sodium combustion flame.Our principle conclusions on sodium combustion under atmospheric air conditions are (a) the maximum theoretical flame temperature is 1950 K, and it is not affected by the presence of moisture; the uppermost limiting factor is the chemical instability of the condensed sodium-oxide products under high temperature; (b) the main combustion product is liquid Na 2 O in dry air condition and liquid Na 2 O with gaseous NaOH in moist air; and (c) the chemical equilibrium prediction of the residual gaseous reactants in the flame is indispensable for sodium combustion modeling

Fitorremediação do herbicida trifloxysulfuron sodium Phytoremediation of the herbicide trifloxysulfuron sodium

Directory of Open Access Journals (Sweden)

J.B. Santos

2004-06-01

Full Text Available Este trabalho teve como objetivo avaliar a eficiência de espécies vegetais na fitorremediação do herbicida trifloxysulfuron sodium em solos, utilizando o milho como planta indicadora. Os tratamentos foram compostos pela combinação de espécies (Calopogonium muconoides, Crotalaria juncea, Crotalaria spectabilis, Vicia sativa, Cajanus cajan, Canavalia ensiformis, Helianthus annus, Dolichus lablab, Pennisetum glaucum, Stylosantes guianensis, Mucuna deeringiana, Mucuna cinereum, Mucuna aterrima, Raphanus sativus e Lupinus albus, semeadas anteriormente à cultura do milho, mais um tratamento controle (sem cultivo prévio e três doses do herbicida trifloxysulfuron sodium (0,00; 3,75; e 15,00 g ha-1. O delineamento experimental usado foi o de blocos ao acaso, em esquema fatorial, sendo utilizadas três repetições. A semeadura das espécies vegetais nos vasos foi feita no dia seguinte à aplicação do trifloxysulfuron sodium. Após 80 dias da semeadura, as espécies vegetais foram cortadas na altura do coleto, descartando-se a sua parte aérea. A seguir, foi realizada a semeadura do milho (cultivar AG-122. Aos 45 dias após a emergência das plantas de milho foram avaliadas a altura de plantas e a sua biomassa seca da parte aérea. Verificou-se que as espécies M. aterrima e C. ensiformis foram eficientes na descontaminação do herbicida trifloxysulfuron sodium em solo.This work aimed to evaluate the efficiency of plant species in the phytoremediation of the herbicide trifloxysulfuron sodium in soils, by using corn crop as a bioindicator. The treatments were composed by the combination of the species (Calopogonium muconoides, Crotalaria juncea, Crotalaria spectabilis, Vicia sativa, Cajanus cajan, Canavalia ensiformis, Helianthus annus, Dolichus lablab, Pennisetum glaucum, Stylosantes guianensis, Mucuna deeringiana, Mucuna cinereum, Mucuna aterrima, Raphanus sativus and Lupinus albus sowed before the corn, without previous cultivation (control

Chloride binding site of neurotransmitter sodium symporters

DEFF Research Database (Denmark)

Kantcheva, Adriana Krassimirova; Quick, Matthias; Shi, Lei

2013-01-01

Neurotransmitter:sodium symporters (NSSs) play a critical role in signaling by reuptake of neurotransmitters. Eukaryotic NSSs are chloride-dependent, whereas prokaryotic NSS homologs like LeuT are chloride-independent but contain an acidic residue (Glu290 in LeuT) at a site where eukaryotic NSSs...

Treatment and processing of residues of fermentation; Behandlung und Verwertung von Gaerrueckstaenden

Energy Technology Data Exchange (ETDEWEB)

Doehler, H.; Schliebner, P. [Kuratorium fuer Technik und Bauwesen in der Landwirtschaft (KTBL), Darmstadt (Germany)

2007-07-01

With the transformation of the EEG (Renewable Energy Resources Act), the number of biogas plants increased rapidly. Additionally, an enlargement of the performance of the plants and a regional concentration process take place. Recently, processing routes for liquid manure will be considered in order to reduce problems of the surplus of nutrients as well as the costs of the transport of the water-rich residues of fermentation. Under this aspect, the authors of the contribution under consideration report on procedures for the processing of residues of fermentation as well as costs and utilization of these procedures. By the example of an agrarian society, four procedures for the output and processing of residues of fermentation are compared with one another regarding to expenditure of work time, investments and economy: Output of residues of fermentation, treatment of residues of fermentation by separation, processing of residues of fermentation by means of diaphragm technology, processing of residues of fermentation by means of evaporation technology. The processing routes reduce the residues of fermentation by 60 %. Thus, the costs of output and the necessary storage capacities for residues of fermentation are reduced. Presently, no savings regarding to work completion by the processing of the residues of fermentation can be obtained. The specific total costs of the investigated procedures are between 2.64 Euro/m{sup 3} according to the procedure with separation and to 8.64 Euro/m{sup 3} according to the diaphragm processing route. An enhanced demand of investment does not cause compellingly the highest specific total costs of the procedures. In comparison to the output of residues of fermentation, the examined procedures for the processing of residues of fermentation do not result in economical and ergonomic advantages. The high costs of investment and operating cost of the processing of residues of fermentation cannot be compensated by the reduced costs of output

Effects of high hydrostatic pressure and varying concentrations of sodium nitrite from traditional and vegetable-based sources on the growth of Listeria monocytogenes on ready-to-eat (RTE) sliced ham.

Science.gov (United States)

Myers, Kevin; Cannon, Jerry; Montoya, Damian; Dickson, James; Lonergan, Steven; Sebranek, Joseph

2013-05-01

The objective of this study was to determine the effect the source of added nitrite and high hydrostatic pressure (HHP) had on the growth of Listeria monocytogenes on ready-to-eat (RTE) sliced ham. Use of 600MPa HHP for 3min resulted in an immediate 3.9-4.3log CFU/g reduction in L. monocytogenes numbers, while use of 400MPa HHP (3min) provided less than 1log CFU/g reduction. With the 600MPa HHP treatment, sliced ham with a conventional concentration of sodium nitrite (200ppm) was not different in L. monocytogenes growth from use with 50 or 100ppm of sodium nitrite in pre-converted celery powder. Instrumental color values as well as residual nitrite and residual nitrate concentrations for cured (sodium nitrite and nitrite from celery powder) and uncured ham formulations are discussed. Copyright © 2013 Elsevier Ltd. All rights reserved.

Sodium-bearing Waste Treatment Technology Evaluation Report

Energy Technology Data Exchange (ETDEWEB)

Charles M. Barnes; Arlin L. Olson; Dean D. Taylor

2004-05-01

Sodium-bearing waste (SBW) disposition is one of the U.S. Department of Energy (DOE) Idaho Operation Office’s (NE-ID) and State of Idaho’s top priorities at the Idaho National Engineering and Environmental Laboratory (INEEL). The INEEL has been working over the past several years to identify a treatment technology that meets NE-ID and regulatory treatment requirements, including consideration of stakeholder input. Many studies, including the High-Level Waste and Facilities Disposition Environmental Impact Statement (EIS), have resulted in the identification of five treatment alternatives that form a short list of perhaps the most appropriate technologies for the DOE to select from. The alternatives are (a) calcination with maximum achievable control technology (MACT) upgrade, (b) steam reforming, (c) cesium ion exchange (CsIX) with immobilization, (d) direct evaporation, and (e) vitrification. Each alternative has undergone some degree of applied technical development and preliminary process design over the past four years. This report presents a summary of the applied technology and process design activities performed through February 2004. The SBW issue and the five alternatives are described in Sections 2 and 3, respectively. Details of preliminary process design activities for three of the alternatives (steam reforming, CsIX, and direct evaporation) are presented in three appendices. A recent feasibility study provides the details for calcination. There have been no recent activities performed with regard to vitrification; that section summarizes and references previous work.

The characterization of insoluble dissolver residues and the development of treatment methods

International Nuclear Information System (INIS)

Baker, H.T.; Brown, P.E.; Pateman, R.J.; Wilkinson, K.L.

1986-01-01

Characterization studies have been carried out on the insoluble residue arising from laboratory scale dissolution of single pins of mixed oxide fuel irradiated in the Dounreay Fast Reactor (DFR). Similar characterization work has also been completed on six samples of insoluble residue recovered from the reprocessing of complete sub-assemblies of mixed oxide fuel irradiated in PFR. Treatment methods for the dissolver insolubles have consisted of preparing immobilized samples in sand/ordinary portland cement (OPC), sand/pulverized fly ash (PFA)/OPC, and blast furnace slag (BFS)/OPC. A programme of leach testing has been carried out according to the conditions laid down in the international Standard Organization Test. Four samples of DFR originated insoluble residues and six samples of PFR originated insoluble residues have been immobilized and leach tested. Variations have included experiments to evaluate the leach rate under temperature influence and to acid wash prior to immobilization

Clinical observation of the combined treatment of edaravone and ozagrel sodium in acute ischemic stroke beyond the thrombolytic time window

Directory of Open Access Journals (Sweden)

SUN Rui-xing

2013-09-01

Full Text Available The curative effect of edaravone combined with ozagrel sodium on acute ischemic stroke beyond the time window of thrombolysis was investigated. A total of 100 patients with acute ischemic stroke beyond the time window of thrombolysis were admitted in our hospital from December 2010 to December 2012. The patients were divided into combined treatment group (N = 50 and ozagrel sodium monotherapy group (control group, N = 50. After 14 days' treatment, total effective rate of the combined treatment group (92% , 46/50 was significantly higher than that of the control group (66% , 33/50; χ2 = 10.780, P = 0.029. After treatment, the nerve function defect score was significantly improved in comparison with before treatment in both groups, but the improvement in combined treatment group (8.21 ± 3.58 was much better than that in the control group (14.60 ± 4.39; t = 7.976, P = 0.000. Therefore, treatment of edaravone combined with ozagrel sodium for patients with acute ischemic stroke beyond the thrombolytic time window can significantly raise the curative effect and improve the neurological function of these patients.

Disinfection of herbal spa pool using combined chlorine dioxide and sodium hypochlorite treatment.

Science.gov (United States)

Hsu, Ching-Shan; Huang, Da-Ji

2015-02-01

The presence of pathogenic microorganisms in public spa pools poses a serious threat to human health. The problem is particularly acute in herbal spas, in which the herbs and microorganisms may interact and produce undesirable consequences. Accordingly, the present study investigated the effectiveness of a combined disinfectant containing chlorine dioxide and sodium hypochlorite in improving the water quality of a public herbal spa in Taiwan. Water samples were collected from the spa pool and laboratory tests were then performed to measure the variation over time of the microorganism content (total CFU and total coliforms) and residual disinfectant content given a single disinfection mode (SDM) with disinfectant concentrations of 5.2 × 10, 6.29 × 10, 7.4 × 10, and 11.4 × 10(-5) N, respectively. Utilizing the experience gained from the laboratory tests, a further series of on-site investigations was performed using three different disinfection modes, namely SDM, 3DM (once every 3 h disinfection mode), and 2DM (once every 2 h disinfection mode). The laboratory results showed that for all four disinfectant concentrations, the CFU concentration reduced for the first 6 h following SDM treatment, but then increased. Moreover, the ANOVA results showed that the sample treated with the highest disinfectant concentration (11.4 × 10(-5) N) exhibited the lowest rate of increase in the CFU concentration. In addition, the on-site test results showed that 3DM and 2DM treatments with disinfectant concentrations in excess of 9.3 × 10 and 5.5 × 10(-5) N, respectively, provided an effective reduction in the total CFU concentration. In conclusion, the experimental results presented in this study provide a useful source of reference for spa businesses seeking to improve the water quality of their spa pools.

Studying oily sludge treatment by thermo chemistry

Directory of Open Access Journals (Sweden)

Jing Guolin

2016-09-01

Full Text Available Nowadays surfactants were used to wash oily sludge and reclaim oil. This paper presents the optimum conditions for washing oily sludge with surfactant solutions using the single factor experiment. The agents tested are AEO-9, Peregal O, TritonX-100, sodium metasilicate and sodium dodecylbenzene sulfonate (DBS. In the experiments, four factors affecting residual oil rate are investigated which include liquid/solid mass rate, reaction temperature, reaction time and eluent mass fraction. Results obtained through experimental runs were compared and used to select a kind of agent, in order to get the best cleaning effect. The optimum parameters of these agents are different from others, and under the optimum conditions their treatment effects are better. And the washing effect of Na2SiO3·9H2O is best and its residual oil rate is only about 1.6%.

Comparison of magnesium sulfate and sodium sulfate for removal of water from pesticide extracts of foods.

Science.gov (United States)

Schenck, Frank J; Callery, Patrick; Gannett, Peter M; Daft, Jonathan R; Lehotay, Steven J

2002-01-01

Water-miscible solvents, such as acetone and acetonitrile, effectively extract both polar and nonpolar pesticide residues from nonfatty foods. The addition of sodium chloride to the resulting acetonitrile-water or acetone-water extract (salting out) results in the separation of the water from the organic solvent. However, the organic solvent layer (pesticide extract) still contains some residual water, which can adversely affect separation procedures that follow, such as solid-phase extraction and/or gas chromatography. Drying agents, such as sodium sulfate or magnesium sulfate, are used to remove the water from the organic extracts. In the present study, we used nuclear magnetic resonance spectroscopy to study the composition of the phases resulting from salting out and to compare the effectiveness of sodium sulfate and magnesium sulfate as drying agents. The study showed that considerable amounts of water remained in the organic phase after phase separation. Sodium sulfate was a relatively ineffective drying agent, removing little or no residual water from the organic solvent. Magnesium sulfate proved to be a much more effective drying agent.

Treatment methods and comparative risks of thorium removal from waste residues

International Nuclear Information System (INIS)

Porter, R.D.; Hamby, D.M.; Martin, J.E.

1997-07-01

This study was done to examine the risks of remediation and the effectiveness of removal methods for thorium and its associated radioactive decay products from various soils and wastes associated with DOE's Formerly Utilized Sites Remedial Action Program (FUSRAP). Removal of 230 Th from uranium process residues would significantly reduce the buildup of 226 Ra (half-life of 1600 years), and since 230 Th concentrations at most of the important sites greatly exceed the 226 Ra concentrations, such removal would reduce the accumulation of additional radiation risks associated with 226 Ra and its products; and, if treatment also removed 226 Ra, these risks could be mitigated even further. Removal of 232 Th from thorium process residues would remove the source material for 228 Ra, and since 228 Ra has a half-life of 5.76 years, its control at FUSRAP sites could be done with land use controls for the 30--50 years required for 228 Ra and the risks associated with its decay products to decay away. It must be recognized, however, that treatment methods invariably require workers to process residues and waste materials usually with bulk handling techniques. These processes expose workers to the radioactivity in the materials, therefore, workers would incur radiological risks in addition to industrial accident risks. An important question is whether the potential reduction of future radiological risks to members of the public justifies the risks that are incurred by remediation workers due to handling materials. This study examines, first, the effectiveness of treatment and then the risks that would be associated with remediation

Analysis of residual stress relief mechanisms in post-weld heat treatment

International Nuclear Information System (INIS)

Dong, Pingsha; Song, Shaopin; Zhang, Jinmiao

2014-01-01

This paper presents a recent study on weld residual stress relief mechanisms associated with furnace-based uniform post-weld heat treatment (PWHT). Both finite element and analytical methods are used to quantitatively examine how plastic deformation and creep relaxation contribute to residual stress relief process at different stages of PWHT process. The key contribution of this work to an improved understanding of furnace based uniform PWHT can be summarized as follows: (1)Plastic deformation induced stress relief during PWHT can be analytically expressed by the change in material elastic deformation capacity (or elastic deformation limit) measured in terms of material yield strength to Young's modulus ratio, which has a rather limited role in overall residual stress relief during furnace based uniform PWHT. (2)The most dominant stress relief mechanism is creep strain induced stress relaxation, as expected. However, a rapid creep strain development accompanied by a rapid residual stress reduction during heating stage before reaching PWHT temperature is shown to contribute to most of the stress relief seen in overall PWHT process, suggesting PWHT hold time can be significantly reduced as far as residual stress relief is concerned. (3)A simple engineering scheme for estimating residual stress reduction is proposed based on this study by relating material type, PWHT temperature, and component wall thickness. - Highlights: • The paper clarified effects of plastic deformation and creep relaxation on weld residual stress relief during uniform PWHT. • Creep strain development is far more important than plastic strain, mostly completed even before hold time starts. • Plastic strain development is insignificant and be analytically described by a material elastic deformation capacity parameter. • An engineering estimation scheme is proposed for determining residual stress reduction resulted from furnace based PWHT

Influence of organic waste and residue mud additions on chemical, physical and microbial properties of bauxite residue sand.

Science.gov (United States)

Jones, Benjamin E H; Haynes, Richard J; Phillips, Ian R

2011-02-01

In an alumina refinery, bauxite ore is treated with sodium hydroxide at high temperatures and pressures and for every tone of alumina produced, about 2 tones of alkaline, saline bauxite processing waste is also produced. At Alcoa, a dry stacking system of disposal is used, and it is the sand fraction of the processing waste that is rehabilitated. There is little information available regarding the most appropriate amendments to add to the processing sand to aid in revegetation. The purpose of this study was to investigate how the addition of organic wastes (biosolids and poultry manure), in the presence or absence of added residue mud, would affect the properties of the residue sand and its suitability for revegetation. Samples of freshly deposited residue sand were collected from Alcoa's Kwinana refinery. Samples were treated with phosphogypsum (2% v/v), incubated, and leached. A laboratory experiment was then set up in which the two organic wastes were applied at 0 or the equivalent to 60 tones ha(-1) in combination with residue mud added at rates of 0%, 10% and 20% v/v. Samples were incubated for 8 weeks, after which, key chemical, physical and microbial properties of the residue sand were measured along with seed germination. Additions of residue mud increased exchangeable Na(+), ESP and the pH, and HCO (3) (-) and Na(+) concentrations in saturation paste extracts. Additions of biosolids and poultry manure increased concentrations of extractable P, NH (4) (+) , K, Mg, Cu, Zn, Mn and Fe. Addition of residue mud, in combination with organic wastes, caused a marked decrease in macroporosity and a concomitant increase in mesoporosity, available water holding capacity and the quantity of water held at field capacity. With increasing residue mud additions, the percentage of sample present as sand particles (2 mm diameter) increased; greatest aggregation occurred where a combination of residue mud and poultry manure were added. Stability of aggregates, as measured by

Mixed-waste treatment -- What about the residuals? A comparative analysis of MSO and incineration

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-06-01

This report examines the issues concerning final waste forms, or residuals, that result from the treatment of mixed waste in molten salt oxidation (MSO) and incinerator systems. MSO is a technology with the potential to treat a certain segment of the waste streams at US Department of Energy (DOE) sites. MSO was compared with incineration because incineration is the best demonstrated available technology (BDAT) for the same waste streams. The Grand Junction Projects Office (GJPO) and Oak Ridge National Laboratory (ORNL) prepared this report for the DOE Office of Environmental Restoration (OER). The goals of this study are to objectively evaluate the anticipated residuals from MSO and incineration, examine regulatory issues for these final waste forms, and determine secondary treatment options. This report, developed to address concerns that MSO residuals present unique disposal difficulties, is part of a larger effort to successfully implement MSO as a treatment technology for mixed and hazardous waste. A Peer Review Panel reviewed the MSO technology in November 1991, and the implementation effort is ongoing under the guidance of the MSO Task Force.

Mixed-waste treatment -- What about the residuals? A comparative analysis of MSO and incineration

International Nuclear Information System (INIS)

1993-06-01

This report examines the issues concerning final waste forms, or residuals, that result from the treatment of mixed waste in molten salt oxidation (MSO) and incinerator systems. MSO is a technology with the potential to treat a certain segment of the waste streams at US Department of Energy (DOE) sites. MSO was compared with incineration because incineration is the best demonstrated available technology (BDAT) for the same waste streams. The Grand Junction Projects Office (GJPO) and Oak Ridge National Laboratory (ORNL) prepared this report for the DOE Office of Environmental Restoration (OER). The goals of this study are to objectively evaluate the anticipated residuals from MSO and incineration, examine regulatory issues for these final waste forms, and determine secondary treatment options. This report, developed to address concerns that MSO residuals present unique disposal difficulties, is part of a larger effort to successfully implement MSO as a treatment technology for mixed and hazardous waste. A Peer Review Panel reviewed the MSO technology in November 1991, and the implementation effort is ongoing under the guidance of the MSO Task Force

Treatment of sodium spills and leakage detection at loop-type fast reactors

Energy Technology Data Exchange (ETDEWEB)

Foerster, K; Fortmann, M; Lang, H; Moellerfeld, H [Interatom, Bergisch Gladbach (Germany)

1979-03-01

Sodium spills are of great importance in the safety analysis for sodium cooled nuclear plants. Large leakages can lead to a depletion of the heat transfer system and cause the loss of cooling of the reactor. Further the hot sodium may attack structural materials. In areas with air atmosphere large amounts of sodium can burn and cause great damages. Therefore the control of large leakages is an indispensable task in design and construction of sodium cooled reactor systems. Because of the typical arrangement of widespread long pipe systems loop type plants are subject to a gradually greater risk of damage than pool type plants. The sodium catching devices of the SNR-300 are described and their function is illustrated as an example for the treatment of large spills. Since the equipment for the control of large amounts of leaking sodium is very expensive, great efforts are made in order to save costs and to decrease safety problems. It is aimed to minimize the probability of such events to a degree that they no longer are to be considered realistic. The advantageous operating conditions and the favourable material properties support this aim. Under the well known keyword 'leak-before-rupture' criterion this task is pursued. Crack growth measurements are made at structural materials under LMFBR conditions, and leakage detecting systems are being developed. Some test results concerning this task are described. Despite the fact that there are good chances to verify the leak-before-rupture criterion it is assumed that certain hypothetical accidents occur, which are to be considered in the design of the reactor plant. The extremely improbable Bethe-Tait-accident (HCDA) is such an event. It would lead to a super spill, that means to the complete depletion of the reactor tank. For the SNR-300 plant a system is provided that is able to catch this super spill and the core melt. This core catcher must withstand the high temperatures and remove the decay heat. The purpose of this

Treatment of sodium spills and leakage detection at loop-type fast reactors

International Nuclear Information System (INIS)

Foerster, K.; Fortmann, M.; Lang, H.; Moellerfeld, H.

1979-01-01

Sodium spills are of great importance in the safety analysis for sodium cooled nuclear plants. Large leakages can lead to a depletion of the heat transfer system and cause the loss of cooling of the reactor. Further the hot sodium may attack structural materials. In areas with air atmosphere large amounts of sodium can burn and cause great damages. Therefore the control of large leakages is an indispensable task in design and construction of sodium cooled reactor systems. Because of the typical arrangement of widespread long pipe systems loop type plants are subject to a gradually greater risk of damage than pool type plants. The sodium catching devices of the SNR-300 are described and their function is illustrated as an example for the treatment of large spills. Since the equipment for the control of large amounts of leaking sodium is very expensive, great efforts are made in order to save costs and to decrease safety problems. It is aimed to minimize the probability of such events to a degree that they no longer are to be considered realistic. The advantageous operating conditions and the favourable material properties support this aim. Under the well known keyword 'leak-before-rupture' criterion this task is pursued. Crack growth measurements are made at structural materials under LMFBR conditions, and leakage detecting systems are being developed. Some test results concerning this task are described. Despite the fact that there are good chances to verify the leak-before-rupture criterion it is assumed that certain hypothetical accidents occur, which are to be considered in the design of the reactor plant. The extremely improbable Bethe-Tait-accident (HCDA) is such an event. It would lead to a super spill, that means to the complete depletion of the reactor tank. For the SNR-300 plant a system is provided that is able to catch this super spill and the core melt. This core catcher must withstand the high temperatures and remove the decay heat. The purpose of this

Treatment of Industrial Liquid Waste of Steel Plating by Coagulation-Flocculation Using Sodium Biphosphate

International Nuclear Information System (INIS)

Subiarto; Herlan Martono

2007-01-01

Research about treatment of industrial liquid waste of steel plating by coagulation-flocculation using sodium biphosphate have been conducted. The purpose of the treatment was the content reduction of Cr, Ni, and Cu in the liquid waste, so that produced effluent with Cr, Ni, and Cu content until they laid under mutual standard. The variables studied in this process were the solution pH, the coagulant/waste volume comparison, the speed of the fast stirring, and the time of the fast stirring. Optimum separation efficiency on coagulation-flocculation process of liquid waste of steel plating using sodium biphosphate at the condition of solution ph 9, coagulant/waste volume comparation 1.50, the speed of the fast stirring 400 rpm, and the time of fast stirring is 5 minute. Low stirring was conducted at 60 rpm for 60 minute. The yields of optimum separation efficiency in this condition were 99.48 % for Cr, 99.51 % for Ni, and 99.03 % for Cu. (author)

Determination of Sodium deoxycolate residues in vaccinal formulation by micellar electrokinetic chromatography

International Nuclear Information System (INIS)

Merchan, Yaima; Lucangioli, Silvia; Carducci, Clyde

2011-01-01

The sodium deoxycholate (DCNa) source is the surfactant used in the biopharmaceutical industry for the solubilization of outer membrane vesicles. It is well known the importance of control of this metabolite in biological materials due to its high toxicity for humans. To demonstrate significant small variations of this metabolite in vaccine formulations it is necessary to use a methodology highly selective, sensitive, specific and reproducible. In this report we used the micellar electrokinetic chromatography (MEKC) in a Capillary Ion Analyzer (Water corp. Milford MA) detection at 185 nm mercury lamp. It employed a fused silica capillary uncoated (Waters Corp. Milford MA). We assessed the purity of 2 lots of sodium deoxycholate and analyzed 15 samples of purified vesicles active pharmaceutical ingredient vaccine formulations. Data were recorded and processed with software Millennium TM (Waters Corp. Milford MA). It was found that lots of sodium deoxycholate containing 1.19 and 0.44% cholic acid and contaminate that 93% of the purified vesicles samples were from 0 to 2.44 mg protein DCNa/100 μg. MECK's results were compared with a kinetic test used to determine bile acids in blood (Merckotest). MECK system showed better results regarding the Merkotest

A process for treatment of residues from dry/semidry APC systems at municipal solid waste incinerators. Final report

Energy Technology Data Exchange (ETDEWEB)

Hjelmar, O. [VKI, Hoersholm (Denmark)] Holland, D. [FLS miljoe a/s, Valby (Denmark)] Poulsen, B. [KARA, Roskilde (Denmark)

1997-08-01

The main objective of the project has been to establish and test a process for treatment of residues from the semidry (and dry) lime injection based APC processes at MSWIs, which will ensure that the residues can be managed in an environmentally safe manner. In pursuit of this goal, the following activities have been carried out: Performance of pilot scale extractions (approximately 50 kg of residue per batch) at the KARA MSWI in Roskilde of semidry APC system residues in order to establish and optimize process conditions. The optimization includes consideration of the possibilities for subsequent treatment/stabilization of the extracted solid phase as well as the possibility of treatment and safe discharge/utilization of the extract; Performance of chemical characterization, hydrogeochemical model calculations and experimental work in order to improve the understanding of the mechanisms and factors which for several contaminants control the equilibrium between the solid and liquid phases, both in the short and the long germ, and to use this information to obtain an environmentally acceptable method for stabilization/treatment of the extracted residues while at the same time minimizing the necessary amount of additives; production of treated residues and performance of leaching tests on these to assess and demonstrate the effectiveness of the entire process (extraction + stabilization/treatment); Evaluation of the technical, economical and environmental consequences of full scale implementation of the process. (EG) EFP-94. 19 refs.

Comparison of efficacy between sodium morrhuate and lauromacrogol as sclerosing agents in treatment of hepatic cyst

Directory of Open Access Journals (Sweden)

QIN Zuyun

2015-07-01

Full Text Available Objective To compare the efficacy of sodium morrhuate versus lauromacrogol in the treatment of hepatic cyst. Methods Seventy-four patients with hepatic cyst who were admitted to our hospital from January 2009 to May 2013 were enrolled as subjects and divided into two groups. After the cystic fluid was drained by percutaneous liver biopsy, sodium morrhuate solution was injected into the cystic cavity for adhesion and sclerosis in 46 patients in group A, and lauromacrogol solution was injected in 28 patients in group B. The incidence rates of pain in patients during and after surgery were compared between the two groups. The follow-up comparison of hepatic cyst recurrence rates within one year after surgery was performed between the two groups. Between-group comparison was performed by χ2 test. Results Five patients (10.87% in group A and two patients (7.14% in group B had recurrence within one year after treatment. There was no significant difference in recurrence rate between the two groups (χ2=0.283, P＞0.05. The incidence of pain in group A was significantly higher than that in group B (χ2=5.258, P＜0.05. Conclusion With the same efficacy as sodium morrhuate in the treatment of hepatic cyst, lauromacrogol can be routinely used as a sclerosing agent due to its mild side effects.

Assessment of residual active chlorine in sodium hypochlorite solutions after dissolution of porcine incisor pulpal tissue.

Science.gov (United States)

Clarkson, R M; Smith, T K; Kidd, B A; Evans, G E; Moule, A J

2013-12-01

In previous studies, surfactant-containing Hypochlor brands of sodium hypochlorite showed better tissue solubilizing abilities than Milton; differences not explained by original active chlorine content or presence of surfactant. It was postulated that exhaustion of active chlorine content could explain differences. This study aimed to assess whether Milton's poorer performance was due to exhaustion of active chlorine. Parallel experiments assessed the influence of titration methods, and the presence of chlorates, on active chlorine measurements. Time required to dissolve one or groups of 10 samples of porcine incisor pulp samples in Milton was determined. Residual active chlorine was assessed by thermometric titration. Iodometric and thermometric titration was carried out on samples of Milton. Chlorate content was also measured. Dissolution of single and 10 pulp samples caused a mean loss of 1% and 3% respectively of active chlorine, not being proportional to tissue dissolved. Thermometric ammonium ion titration resulted in 10% lower values than iodometric titration. Chlorate accounted for much of this difference. Depletion of active chlorine is not the reason for differences in tissue dissolving capabilities of Milton. Thermometric ammonium ion titration gives more accurate measurement of active chlorine content than iodometric titration. © 2013 Australian Dental Association.

Treatment methods and comparative risks of thorium removal from waste residues

Energy Technology Data Exchange (ETDEWEB)

Porter, R.D.; Hamby, D.M.; Martin, J.E.

1997-07-01

This study was done to examine the risks of remediation and the effectiveness of removal methods for thorium and its associated radioactive decay products from various soils and wastes associated with DOE`s Formerly Utilized Sites Remedial Action Program (FUSRAP). Removal of {sup 230}Th from uranium process residues would significantly reduce the buildup of {sup 226}Ra (half-life of 1600 years), and since {sup 230}Th concentrations at most of the important sites greatly exceed the {sup 226}Ra concentrations, such removal would reduce the accumulation of additional radiation risks associated with {sup 226}Ra and its products; and, if treatment also removed {sup 226}Ra, these risks could be mitigated even further. Removal of {sup 232}Th from thorium process residues would remove the source material for {sup 228}Ra, and since {sup 228}Ra has a half-life of 5.76 years, its control at FUSRAP sites could be done with land use controls for the 30--50 years required for {sup 228}Ra and the risks associated with its decay products to decay away. It must be recognized, however, that treatment methods invariably require workers to process residues and waste materials usually with bulk handling techniques. These processes expose workers to the radioactivity in the materials, therefore, workers would incur radiological risks in addition to industrial accident risks. An important question is whether the potential reduction of future radiological risks to members of the public justifies the risks that are incurred by remediation workers due to handling materials. This study examines, first, the effectiveness of treatment and then the risks that would be associated with remediation.

Treatment of Lignin and Waste residues by Flash Pyrolysis

DEFF Research Database (Denmark)

Jensen, Peter Arendt; Trinh, Ngoc Trung; Dam-Johansen, Kim

pyrolysis properties were compared with the pyrolysis properti es of wood and straw. The PCR treatment of sewage sludge provides an oil that can be used for energy pur poses and a solid residue rich in in organic nutrients that may be used as fertilizer product. By fast pyroly sis of lignin from the IBUS...... be operated at low rotational speed was constructed. The new rotor systems should make it easier to make an up-scaling of the process....

Simulation of Distortion and Residual Stress Development During Heat Treatment of Steel Castings

Energy Technology Data Exchange (ETDEWEB)

Beckermann, Christoph; Carlson, Kent

2011-07-22

Heat treatment and associated processing, such as quenching, are critical during high strength steel casting production. These processes must be managed closely to prevent thermal and residual stresses that may result in distortion, cracking (particularly after machining), re-work, and weld repair. The risk of casting distortion limits aggressive quenching that can be beneficial to the process and yield an improved outcome. As a result of these distortions, adjustments must be made to the casting or pattern design, or tie bars must be added. Straightening castings after heat treatments can be both time-consuming and expensive. Residual stresses may reduce a casting's overall service performance, possibly resulting in catastrophic failure. Stress relieving may help, but expends additional energy in the process. Casting software is very limited in predicting distortions during heat treatment, so corrective measures most often involve a tedious trial-and-error procedure. An extensive review of existing heat treatment residual stress and distortion modeling revealed that it is vital to predict the phase transformations and microstructure of the steel along with the thermal stress development during heat treatment. After reviewing the state-of-the-art in heat treatment residual stress and distortion modeling, an existing commercial code was selected because of its advanced capabilities in predicting phase transformations, the evolving microstructure and related properties along with thermal stress development during heat treatment. However, this software was developed for small parts created from forgings or machined stock, and not for steel castings. Therefore, its predictive capabilities for heat treatment of steel castings were investigated. Available experimental steel casting heat treatment data was determined to be of insufficient detail and breadth, and so new heat treatment experiments were designed and performed, casting and heat treating modified versions

Residual stress and mechanical properties of SiC ceramic by heat treatment

International Nuclear Information System (INIS)

Yoon, H.K.; Kim, D.H.; Shin, B.C.

2007-01-01

Full text of publication follows: Silicon carbide is a compound of relatively low density, high hardness, elevated thermal stability and good thermal conductivity, resulting in good thermal shock resistance. Because of these properties, SiC materials are widely used as abrasives and refractories. In this study, SiC single and poly crystals was grown by the sublimation method using the SiC seed crystal and SiC powder as the source material. Mechanical properties of SiC single and poly crystals are carried out by using the nano-indentation method and small punch test after the heat treatment. As a result, mechanical properties of SiC poly crystal had over double than single. And SiC single and poly crystals were occurred residual stress, but residual stress was shown relaxant properties by the effect of heat treatment. (authors)

Coulometric sodium chloride removal system with Nafion membrane for seawater sample treatment.

Science.gov (United States)

Grygolowicz-Pawlak, Ewa; Sohail, Manzar; Pawlak, Marcin; Neel, Bastien; Shvarev, Alexey; de Marco, Roland; Bakker, Eric

2012-07-17

Seawater analysis is one of the most challenging in the field of environmental monitoring, mainly due to disparate concentration levels between the analyte and the salt matrix causing interferences in a variety of analytical techniques. We propose here a miniature electrochemical sample pretreatment system for a rapid removal of NaCl utilizing the coaxial arrangement of an electrode and a tubular Nafion membrane. Upon electrolysis, chloride is deposited at the Ag electrode as AgCl and the sodium counterions are transported across the membrane. This cell was found to work efficiently at potentials higher than 400 mV in both stationary and flow injection mode. Substantial residual currents observed during electrolysis were found to be a result of NaCl back diffusion from the outer side of the membrane due to insufficient permselectivity of the Nafion membrane. It was demonstrated that the residual current can be significantly reduced by adjusting the concentration of the outer solution. On the basis of ion chromatography results, it was found that the designed cell used in flow injection electrolysis mode reduced the NaCl concentration from 0.6 M to 3 mM. This attempt is very important in view of nutrient analysis in seawater where NaCl is a major interfering agent. We demonstrate that the pretreatment of artificial seawater samples does not reduce the content of nitrite or nitrate ions upon electrolysis. A simple diffusion/extraction steady state model is proposed for the optimization of the electrolysis cell characteristics.

The various sodium purification techniques

International Nuclear Information System (INIS)

Courouau, J.L.; Masse, F.; Rodriguez, G.; Latge, C.; Redon, B.

1997-01-01

In the framework of sodium waste treatment, the sodium purification phase plays an essential role in the chain of operations leading to the transformation of the active sodium, considered as waste, into a stable sodium salt. The objectives of the purification operations are: To keep a low impurity level, particularly a low concentration in oxygen and hydrogen, in order to allow its transfer to a processing plant, and in order to avoid risks of plugging and/or corrosion in sodium facilities; To reduce the sodium activity in order to limit the dose rate close to the facilities, and in order to reduce the activity of the liquid and gaseous effluents. After a recall of the different kind of impurities that can be present in sodium, and of the different purification methods that could be associated with, the following points are highlighted: (i) Oxygen and hydrogen purification needs, and presentation of some selection criteria for a purification unit adapted to a sodium processing plant, as well as 2 cold trap concepts that are in accordance with these criteria: PSICHOS and PIRAMIDE. (ii) Tritium reduction in a bulk of liquid sodium by swamping, isotopic exchange, or permeation throughout a membrane. (iii) Caesium trapping on carbonaceous matrix. The main matrices used at present are R.V.C. (Reticulated Vitreous Carbon) and Actitex/Pica products. Tests in the laboratory and on an experimental device have demonstrated the performances of these materials, which are able to reduce sodium activity in Cs 134 and Cs 137 to very low values. The sodium purification processes as regards to the hydrogen, oxygen and caesium, that are aimed at facilitating the subsequent treatment of sodium, are therefore mastered operations. Regarding the operations associated with the reduction of the tritium activity, the methods are in the process of being qualified, or to be qualified. (author)

Efficiency Improvement of Some Agricultural Residue Modified Materials for Textile Dyes Absorption

Science.gov (United States)

Boonsong, P.; Paksamut, J.

2018-03-01

In this work, the adsorption efficiency was investigated of some agricultural residue modified materials as natural bio-adsorbents which were rice straw (Oryza sativa L.) and pineapple leaves (Ananas comosus (L.) Merr.) for the removal of textile dyes. Reactive dyes were used in this research. The improvement procedure of agricultural residue materials properties were alkali-acid modification with sodium hydroxide solution and hydrochloric acid solution. Adsorption performance has been investigated using batch experiments. Investigated adsorption factors consisted of adsorbent dose, contact time, adsorbent materials and pH of solution. The results were found that rice straw had higher adsorption capacity than pineapple leaves. The increasing of adsorption capacity depends on adsorbent dose and contact time. Moreover, the optimum pH for dye adsorption was acidic range because lowering pH increased the positively charges on the adsorbent surface which could be attacked by negatively charge of acid dyes. The agricultural residue modified materials had significant dye removal efficiency which these adsorbents could be used for the treatment of textile effluent in industries.

EXPERIENCE OF DESOXIRIBONUCLEATE SODIUM IMMUNOMODULATOR APPLICATION IN TREATMENT FOR REACTIVE ARTHRITIS OF CHLAMYDIA AETIOLOGY AMONG CHILDREN

Directory of Open Access Journals (Sweden)

L.A. Balykova

2007-01-01

Full Text Available Researchers compared efficacy of the conventional therapy (oilment with non steriod anti-inflammatory medication, diclofena sodium and azithromycin among children with reactive arthritis of Chlamydia etiology and treatment with introduction of gluccosaminilmuramildi peptide and desoxiribonucleate sodium immunomodulators. The article shows that application of immunomodulators in combination with the conventional therapy provided for the decrease of the articular syndrome intensity, reduced the need of the patients in local corticosteroids and conduced to the reduction of the lab process activity indices. Further more, they noticed reduced recurrence of the antibodies to Chlamydias and their titers in the blood serum, while general intensity of the antiinflammatory effects from the combined therapy, which included glucosaminilmuramildipeptide and desoxiribonucleate sodium immunomodulators along with the antibiotic, proved to be comparable.Key words: children, reactive arthritis, chlamydia infection, immunomodulators.

Treatment of products from petroleum, shale, coal, lignite, etc

Energy Technology Data Exchange (ETDEWEB)

Jevanoff, V

1952-06-20

An improved process is described for treating with sodium plumbite all the products derived from crude petroleum, bituminous shale, coal, lignite, peat, etc., such as gasoline, solvents, lamp oil, gas oil, fuels, etc; the process being essentially characterized by the fact that it consists first in washing the product to be refined with a soda wash; submitting it to a treatment with sodium plumbite, without addition of sulfur, then to eliminate the sulfur plumbite compounds resulting in the treated product, using either redistillation to eliminate products remaining in the residue or filtration over an absorbing material such as active carbon, decolorizing earths.

Sodium transport through the cerebral sodium-glucose transporter exacerbates neuron damage during cerebral ischaemia.

Science.gov (United States)

Yamazaki, Yui; Harada, Shinichi; Wada, Tetsuyuki; Yoshida, Shigeru; Tokuyama, Shogo

2016-07-01

We recently demonstrated that the cerebral sodium-glucose transporter (SGLT) is involved in postischaemic hyperglycaemia-induced exacerbation of cerebral ischaemia. However, the associated SGLT-mediated mechanisms remain unclear. Thus, we examined the involvement of cerebral SGLT-induced excessive sodium ion influx in the development of cerebral ischaemic neuronal damage. [Na+]i was estimated according to sodium-binding benzofuran isophthalate fluorescence. In the in vitro study, primary cortical neurons were prepared from fetuses of ddY mice. Primary cortical neurons were cultured for 5 days before each treatment with reagents, and these survival rates were assessed using biochemical assays. In in vivo study, a mouse model of focal ischaemia was generated using middle cerebral artery occlusion (MCAO). In these experiments, treatment with high concentrations of glucose induced increment in [Na+]i, and this phenomenon was suppressed by the SGLT-specific inhibitor phlorizin. SGLT-specific sodium ion influx was induced using a-methyl-D-glucopyranoside (a-MG) treatments, which led to significant concentration-dependent declines in neuronal survival rates and exacerbated hydrogen peroxide-induced neuronal cell death. Moreover, phlorizin ameliorated these effects. Finally, intracerebroventricular administration of a-MG exacerbated the development of neuronal damage induced by MCAO, and these effects were ameliorated by the administration of phlorizin. Hence, excessive influx of sodium ions into neuronal cells through cerebral SGLT may exacerbate the development of cerebral ischaemic neuronal damage. © 2016 Royal Pharmaceutical Society.

Municipal solid waste options : integrating organics management and residual disposal treatment : executive summary

Energy Technology Data Exchange (ETDEWEB)

Cant, M. (comp.) [Totten Sims Hubicki Associates Ltd., Calgary, AB (Canada); Van der Werf, P. [2cg Inc., Edmonton, AB (Canada); Kelleher, M. [Kelleher Environmental, Toronto, ON (Canada); Merriman, D. [MacViro Consultants, Markham, ON (Canada); Fitcher, K. [Gartner Lee Ltd., Toronto, ON (Canada); MacDonald, N. [CH2M Hill Engineering Ltd., Calgary, AB (Canada)

2006-04-15

The Municipal Solid Waste (MSW) Options Report explored different MSW management options for 3 community sizes: 20,000, 80,000 and 200,0000 people. It was released at a time when many communities were developing waste management plans to cost-effectively reduce environmental impacts and conserve landfill capacity. The purpose of this report was to provide a greater understanding on the environmental, social, economic, energy recovery/utilization and greenhouse gas (GHG) considerations of MSW management. The report also demonstrated the interrelationships between the management of organics and residuals. It was based on information from existing waste diversion and organics management options and emerging residual treatment technology options. The following organics management and residual treatment disposal options were evaluated: composting; anaerobic digestion; sanitary landfills; bioreactor landfills; and thermal treatment. Composting was examined with reference to both source separated organics (SSO) and mixed waste composting. SSO refers to the separation of materials suitable for composting solid waste from households, while mixed waste composting refers to the manual or mechanical removal of recyclable material from the waste, including compost. The composting process was reviewed along with available technologies such as non-reactor windrow; aerated static pile; reactor enclosed channel; and, container tunnel. An evaluation of SSO and mixed waste composting was then presented in terms of environmental, social, financial and GHG impacts. refs., tabs., figs.

Objective Provision Tree (OPT) in sodium cooled fast reactors; Objective Provision Tree (OPT) en reactores rapidos refrigerados por sodio. Aplicacion a la funcion de seguridad de evacuacion de calor residual

Energy Technology Data Exchange (ETDEWEB)

Queral, C.; Montero-Mayorga, J.; Gonzalez-Cadelo, J.

2013-07-01

Application to the safety function of residual heat removal As part of the project {sup S}afety Assessment for Reactor of GEN-IV (SARGEN IV) has been implemented the methodology ISAM from the IAEA to the safety assessment of new sodium reactor designs. Within the ISAM, a new tool to facilitate this assessment is the Objective Provision Tree (OPT) which documents the provisions necessary for each of the levels of defense in depth, as well as for each critical function of security. Due to the design innovations that have sodium reactors, the evaluation of safety and licensing of these reactors requires special considerations. In this work we have analyzed the mechanisms of failure of the safety function concerning the evacuation of waste heat, and have been proposed different provisions for each of the first three levels of defense in depth. The main result of this work is reflected in the elaboration of the OPTs, one for each of the first three levels of defense in depth for the safety of evacuation of residual heat function. These trees represent in a schematic way the provisions necessary to comply with the objectives of each level which are respectively: 1) deviations from normal operation, 2) control of abnormal operation and fault detection and 3) incidental control.

Lithium clearance and renal tubular sodium handling during acute and long-term nifedipine treatment in essential hypertension

DEFF Research Database (Denmark)

Bruun, N E; Ibsen, H; Skøtt, P

1988-01-01

1. In two separate studies the lithium clearance method was used to evaluate the influence of acute and long-term nifedipine treatment on renal tubular sodium reabsorption. 2. In the acute study, after a 4 week placebo period two doses of 20 mg of nifedipine decreased supine blood pressure from 155...... were also unchanged, as were potassium clearance, urine flow and body weight. 3. In the long-term study, lithium clearance, glomerular filtration rate, sodium clearance, potassium clearance, urine flow and body fluid volumes were measured after a 4 weeks placebo period and after 6 and 12 weeks....../101 (20.6/13.5) +/- 11/4 (1.5/0.5) to 139/88 (18.5/11.7) +/- 16/9 (2.1/1.2) mmHg (kPa) (means +/- SD; P less than 0.01). Lithium clearance, glomerular filtration rate and sodium clearance did not change. Therefore the calculated values of absolute proximal and absolute distal sodium reabsorption rates...

TXNIP mediates the differential responses of A549 cells to sodium butyrate and sodium 4-phenylbutyrate treatment.

Science.gov (United States)

Jin, Xuefang; Wu, Nana; Dai, Juji; Li, Qiuxia; Xiao, XiaoQiang

2017-02-01

Sodium butyrate (NaBu) and sodium 4-phenylbutyrate (4PBA) have promising futures in cancer treatment; however, their underlying molecular mechanisms are not clearly understood. Here, we show A549 cell death induced by NaBu and 4PBA are not the same. NaBu treatment induces a significantly higher level of A549 cell death than 4PBA. A gene expression microarray identified more than 5000 transcripts that were altered (>1.5-fold) in NaBu-treated A549 cells, but fewer than 2000 transcripts that were altered in 4PBA. Moreover, more than 100 cell cycle-associated genes were greatly repressed by NaBu, but slightly repressed by 4PBA; few genes were significantly upregulated only in 4PBA-treated cells. Gene expression was further validated by other experiments. Additionally, A549 cells that were treated with these showed changes in glucose consumption, caspase 3/7 activation and histone modifications, as well as enhanced mitochondrial superoxide production. TXNIP was strongly induced by NaBu (30- to 40-fold mRNA) but was only slightly induced by 4PBA (two to fivefold) in A549 cells. TXNIP knockdown by shRNA in A549 cells significantly attenuated caspase 3/7 activation and restored cell viability, while TXNIP overexpression significantly increased caspase 3/7 activation and cell death only in NaBu-treated cells. Moreover, TXNIP also regulated NaBu- but not 4PBA-induced H4K5 acetylation and H3K4 trimethylation, possibly by increasing WDR5 expression. Finally, we demonstrated that 4PBA induced a mitochondrial superoxide-associated cell death, while NaBu did so mainly through a TXNIP-mediated pathway. The above data might benefit the future clinic application. © 2016 The Authors. Cancer Medicine published by John Wiley & Sons Ltd.

Evaluation of some residual bioactivities of microencapsulated Phaseolus lunatus protein fraction with carboxymethylated flamboyant (Delonix regia gum/sodium alginate

Directory of Open Access Journals (Sweden)

Mukthar Sandovai-Peraza

2014-12-01

Full Text Available Recent studies have shown the beneficial effect of peptides, an unexploited source could be Phaseolus lunatus being an important raw material for those functional products in order to improve their utilization. In addition to improve the beneficial effect of bioactive peptides the microencapsulation could be a way to protect the peptides against the environment to which they are exposed. P. lunatus protein fraction (<10 kDa of weight was encapsulated using a blend of carboxymethylated flamboyant gum (CFG and sodium alginate (SA at different concentrations of CaCl2 and hardening times. After in vitro digestion of microcapsules the residual activity, in the intestinal system, both inhibition of agiotensin-converting enzyme (I-ACE and antioxidant activity obtained were in a range of 0.019-0.136 mg/mL and 570.64-813.54 mM of TEAC respectively. The microencapsulation employed CFG/SA blends could be used controlled delivery of peptide fractions with potential use as a nutraceutical or therapeutic agents.

Residual stress development and relief in high strength aluminium alloys using standard and retrogression thermal treatments

OpenAIRE

Robinson, J.S; Tanner, D.A

2003-01-01

peer-reviewed Residual stresses develop in the aluminium alloy 7010 when the material is quenched from the solution heat treatment temperature. Residual stress measurements have been made using the X-ray diffraction technique and a longitudinal split sawcut method to determine the magnitude of residual stress that develops in specimens sectioned from large open die forgings as a result of (a) quenching these specimens into water at different temperatures, and (b) cold water quenching from ...

Identification of galactose as the immunodominant sugar of leishmanial excreted factor and subsequent labeling with galactose oxidase and sodium boro[3H]hydride.

Science.gov (United States)

Slutzky, G M; Greenblatt, C L

1982-01-01

Inhibition by low-molecular-weight sugars of precipitin line formation between a polysaccharide (EF) excreted by Leishmania tropica subsp. major, Leishmania enriettii, and rabbit antileishmanial antibodies on double gel diffusion plates revealed that galactose residues, possibly as components of lactosyl groups, were the critical immunodominant sugars mediating antibody recognition of EF. The galactose residues of the EF of L. tropica subsp. major were specifically labeled with tritium via galactose oxidase and sodium boro[3H]hydride. The radioactive EF had an apparent molecular weight of about 85,000 on sodium dodecyl sulfate-polyacrylamide gels and was precipitated by antileishmanial antibodies as well as Ricinus communis lectins I and II (galactose specific). Lectins specific for glucose-mannose residues, fucose, N-acetylglucosamine, and N-acetylgalactosamine did not precipitate the labeled EF. Treatment of [3H]EF with proteolytic (trypsin, papain, protease) or glycosidic (alpha-amylase, beta-galactosidase) enzymes had no effect on either the electrophoretic pattern of the material or on its recognition by antileishmanial antibodies or R. communis lectin. This resistance to enzyme activity suggests that EF may be a useful marker for the presence of the parasite in vivo if it can be detected in minute quantities. PMID:6179874

Safe apples for baby-food production: survey of pesticide treatment regimes leaving minimum residues.

Science.gov (United States)

Ticha, Jana; Hajslova, Jana; Kovalczuk, Tomas; Jech, Martin; Honzicek, Jiri; Kocourek, Vladimir; Lansky, Miroslav; Kloutvorova, Jana; Falta, Vladan

2007-06-01

A total of 19 pesticide preparations were used according to agricultural practice in six trials in apple orchards. Using gas chromatography-mass spectrometry (GC-MS) and liquid chromatography-tandem mass spectrometry (LC-MS/MS), premature Golden Delicious apples collected 64, 50, 36 days before harvest and mature fruit were examined for residues of active ingredients. No residues of triflumuron, triazamate, chlorpyrifos, etofenprox, fenoxycarb, kresoxim-methyl, cyprodinyl, difenoconazole or thiram were detected in the first sampling. Also, the levels of chlorpyrifos-methyl, penconazole, tebuconazole and tolylfluanid dropped during the pre-harvest interval. Detectable residues of pyridaben, thiacloprid, trifloxystrobin and tetraconazole in harvested fruits were below 0.01 mg kg(-1), which is the maximum concentration of residues acceptable by baby-food producers in any raw material. The only residues exceeding this concentration were captan and teflubenzuron. Based on the data, farmers can choose pesticides for optimal treatment of plants, while enabling growth of a safe crop suitable for baby-food production.

Acute Cyanide Poisoning: Hydroxocobalamin and Sodium Thiosulfate Treatments with Two Outcomes following One Exposure Event

OpenAIRE

Meillier, Andrew; Heller, Cara

2015-01-01

Cyanide is rapidly reacting and causes arrest of aerobic metabolism. The symptoms are diffuse and lethal and require high clinical suspicion. Remediation of symptoms and mortality is highly dependent on quick treatment with a cyanide antidote. Presently, there are two widely accepted antidotes: sodium thiosulfate and hydroxocobalamin. These treatments act on different components of cyanide’s metabolism. Here, we present two cases resulting from the same source of cyanide poisoning and the use...

A previously undescribed organic residue sheds light on heat treatment in the Middle Stone Age.

Science.gov (United States)

Schmidt, Patrick; Porraz, Guillaume; Bellot-Gurlet, Ludovic; February, Edmund; Ligouis, Bertrand; Paris, Céline; Texier, Pierre-Jean; Parkington, John E; Miller, Christopher E; Nickel, Klaus G; Conard, Nicholas J

2015-08-01

South Africa has in recent years gained increasing importance for our understanding of the evolution of 'modern human behaviour' during the Middle Stone Age (MSA). A key element in the suite of behaviours linked with modern humans is heat treatment of materials such as ochre for ritual purposes and stone prior to tool production. Until now, there has been no direct archaeological evidence for the exact procedure used in the heat treatment of silcrete. Through the analysis of heat-treated artefacts from the Howiesons Poort of Diepkloof Rock Shelter, we identified a hitherto unknown type of organic residue - a tempering-residue - that sheds light on the processes used for heat treatment in the MSA. This black film on the silcrete surface is an organic tar that contains microscopic fragments of charcoal and formed as a residue during the direct contact of the artefacts with hot embers of green wood. Our results suggest that heat treatment of silcrete was conducted directly using an open fire, similar to those likely used for cooking. These findings add to the discussion about the complexity of MSA behaviour and appear to contradict previous studies that had suggested that heat treatment of silcrete was a complex (i.e., requiring a large number of steps for its realization) and resource-consuming procedure. Copyright © 2015 Elsevier Ltd. All rights reserved.

Sources of manganese in the residue from a water treatment plant ...

African Journals Online (AJOL)

Disposal of water treatment residue (WTR), the by-product from the production of potable water, has traditionally been to landfill. The shortage of suitable landfill sites has led to the proposal that WTR be applied to land. Such disposal is only possible if the WTR contains no toxic elements that may contaminate soil, water or ...

One Year Experience of Pheburane® (Sodium Phenylbutyrate) Treatment in a Patient with Argininosuccinate Lyase Deficiency

OpenAIRE

Uçar, Sema Kalkan; Ozbaran, Burcu; Altinok, Yasemin Atik; Kose, Melis; Canda, Ebru; Kagnici, Mehtap; Coker, Mahmut

2015-01-01

Argininosuccinate lyase deficiency (ASLD) is a urea cycle disorder (UCD) treated with dietary adjustment and nitrogen scavenging agents. “Pheburane®” is a new tasteless and odour-free formulation of sodium phenylbutyrate, indicated in the treatment of UCD.

The role of aspartic acid residues 405 and 416 of the kidney isotype of sodium-bicarbonate cotransporter 1 in its targeting to the plasma membrane

Science.gov (United States)

Kucher, Volodymyr; Li, Emily Y.; Conforti, Laura; Zahedi, Kamyar A.

2012-01-01

The NH2 terminus of the sodium-bicarbonate cotransporter 1 (NBCe1) plays an important role in its targeting to the plasma membrane. To identify the amino acid residues that contribute to the targeting of NBCe1 to the plasma membrane, polarized MDCK cells were transfected with expression constructs coding for green fluorescent protein (GFP)-tagged NBCe1 NH2-terminal deletion mutants, and the localization of GFP-tagged proteins was analyzed by confocal microscopy. Our results indicate that the amino acids between residues 399 and 424 of NBCe1A contain important sequences that contribute to its localization to the plasma membrane. Site-directed mutagenesis studies showed that GFP-NBCe1A mutants D405A and D416A are retained in the cytoplasm of the polarized MDCK epithelial cells. Examination of functional activities of D405A and D416A reveals that their activities are reduced compared with the wild-type NBCe1A. Similarly, aspartic acid residues 449 and 460 of pancreatic NBCe1 (NBCe1B), which correspond to residues 405 and 416 of NBCe1A, are also required for its full functional activity and accurate targeting to the plasma membrane. In addition, while replacement of D416 with glutamic acid did not affect the targeting or functional activity of NBCe1A, substitution of D405 with glutamic acid led to the retention of the mutated protein in the intracellular compartment and impaired functional activity. These studies demonstrate that aspartic acid residues 405 and 416 in the NH2 terminus of NBCe1A are important in its accurate targeting to the plasma membrane. PMID:22442137

Sodium Oxybate treatment in pediatric type 1 narcolepsy.

Science.gov (United States)

Moresco, Monica; Pizza, Fabio; Antelmi, Elena; Plazzi, Giuseppe

2018-03-05

Narcolepsy type 1 (NT1) is a rare chronic neurologic disorder characterized by excessive daytime sleepiness, cataplexy, sleep paralysis, hallucinations and disrupted nocturnal sleep, usually with onset during childhood/adolescence. Pediatric NT1 is associated with limitations on children's activities and achievements, especially poor performance at school, difficulty with peers due to disease symptoms and comorbidities including depression, obesity, and precocious puberty. NT1 disease is caused by the selective loss of hypocretin-producing neurons in the lateral hypothalamus, most probably related to an autoimmune pathophysiology. Indeed a strong genetic predisposition including the HLA system and other associations in genes involved in immune responses has been found together with the triggering role of environmental agents such as H1N1 influenza infections and vaccinations. Sodium Oxybate (SO) is a sodium salt of γ-hydroxybutyric (GHB) acid that is synthetized by neurons in the brain and functions as neurotransmitter. GHB is a central nervous system depressant and produces dose-dependent sedation. SO is a first line medication for cataplexy and excessive daytime sleepiness in adults with NT1, but can be helpful also for sleep disruption, hypnagogic hallucination and sleep paralysis in these patients. Although in the majority of patients narcolepsy develops before 15 years of age, there are no approved treatments for pediatric NT1. However, SO has been widely used off-label to treat narcolepsy symptoms in children and adolescents with NT1 in non-controlled studies, showing a similar safety profile and therapeutic response to adult patients. Current therapy is based only on empirical data shared among expert sleep disorders clinicians. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

Evaluating the SCC resistance of underwater welds in sodium tetrathionate

International Nuclear Information System (INIS)

White, R.A.; Angeliu, T.M.

1997-01-01

The susceptibility of welds to stress corrosion cracking (SCC) is enhanced by the surface residual tensile stresses generated by the typical welding process. However, underwater plasma transferred arc (PTA) welding has been shown to produce compressive surface residual stresses, an encouraging result if repairs of cracked boiling water reactor (BWR) components are to be made without further endangering them to SCC. This program was designed to verify that underwater PTA welds are resistant to SCC and to determine if underwater PTA welding could mitigate SCC in potentially susceptible welds. This was achieved by exposing various welds on solution annealed (SA) and SA + thermally sensitized 304 stainless steel at 25 C in a solution of 1.5 gm/liter of sodium sulfide added to 0.05M sodium tetrathionate, titrated to a pH of 1.25 with H 2 SO 4 . The autogeneous welds were produced using gas tungsten arc (GTA) and plasma transferred arc (PTA) welding under atmospheric conditions, and PTA welding underwater. After 1 hour of sodium tetrathionate exposure, GTA and air PTA welds exhibited SCC while the underwater PTA weld heat affected zones were more resistant. Underwater PTA welds bisecting a GTA weld eliminated the cracking in the GTA weld heat affected zone under certain conditions. The lack of IG cracking in the region influenced by the underwater PTA weld is consistent with the measurement of compressive surface residual stresses inherent to the underwater welding process

A brief history of residual alkali metal destruction development in the UK

International Nuclear Information System (INIS)

Fletcher, Brian

2014-01-01

The reactors at Dounreay are being decommissioned and there is a need to remove all the residual alkali metal before they can be dismantled. When the Prototype Fast Reactor was shut down work was started to remove the bulk sodium and development of the Water Vapour Nitrogen (WVN) process for the destruction of the residual alkali metal commenced. This development has been ongoing to the present day. Trials began with small amounts of sodium and NaK before moving to larger scale experiments. The development raised a number of issues. As knowledge was built up, the development was expanded to deal with NaK pools in the DFR. Differences in the behaviour of NaK and sodium led to various different processes being developed. This paper presents a brief history of the alkali metal destruction process development within the UK and highlights some of the lessons learnt for future application during reactor decommissioning (authors)

Sodium Nitrite and Sodium Thiosulfate Are Effective Against Acute Cyanide Poisoning When Administered by Intramuscular Injection.

Science.gov (United States)

Bebarta, Vikhyat S; Brittain, Matthew; Chan, Adriano; Garrett, Norma; Yoon, David; Burney, Tanya; Mukai, David; Babin, Michael; Pilz, Renate B; Mahon, Sari B; Brenner, Matthew; Boss, Gerry R

2017-06-01

The 2 antidotes for acute cyanide poisoning in the United States must be administered by intravenous injection. In the out-of-hospital setting, intravenous injection is not practical, particularly for mass casualties, and intramuscular injection would be preferred. The purpose of this study is to determine whether sodium nitrite and sodium thiosulfate are effective cyanide antidotes when administered by intramuscular injection. We used a randomized, nonblinded, parallel-group study design in 3 mammalian models: cyanide gas inhalation in mice, with treatment postexposure; intravenous sodium cyanide infusion in rabbits, with severe hypotension as the trigger for treatment; and intravenous potassium cyanide infusion in pigs, with apnea as the trigger for treatment. The drugs were administered by intramuscular injection, and all 3 models were lethal in the absence of therapy. We found that sodium nitrite and sodium thiosulfate individually rescued 100% of the mice, and that the combination of the 2 drugs rescued 73% of the rabbits and 80% of the pigs. In all 3 species, survival in treated animals was significantly better than in control animals (log rank test, Pcyanide poisoning in 3 clinically relevant animal models of out-of-hospital emergency care. Copyright © 2016 American College of Emergency Physicians. Published by Elsevier Inc. All rights reserved.

Lowest neonatal serum sodium predicts sodium intake in low birth weight children.

Science.gov (United States)

Shirazki, Adi; Weintraub, Zalman; Reich, Dan; Gershon, Edith; Leshem, Micah

2007-04-01

Forty-one children aged 10.5 +/- 0.2 years (range, 8.0-15.0 yr), born with low birth weight of 1,218.2 +/- 36.6 g (range, 765-1,580 g) were selected from hospital archives on the basis of whether they had received neonatal diuretic treatment or as healthy matched controls. The children were tested for salt appetite and sweet preference, including rating of preferred concentration of salt in tomato soup (and sugar in tea), ratings of oral spray (NaCl and sucrose solutions), intake of salt or sweet snack items, and a food-seasoning, liking, and dietary questionnaire. Results showed that sodium appetite was not related to neonatal diuretic treatment, birth weight, or gestational age. However, there was a robust inverse correlation (r = -0.445, P clear that perinatal sodium loss, from a variety of causes, is a consistent and significant contributor to long-term sodium intake.

Study of sodium combustion and fire extinction by pulverized substances. Role of additives

International Nuclear Information System (INIS)

Reuillon, Marcelline.

1976-01-01

A study is presented on inflammation and combustion of liquid sodium, extinction of the metal fires by comburant concentration reducing and cooling, liquid covering, powder smothering. The role of the additives is discussed. The setting up and the experimental process are given. The sodium combustion residues are analyzed. Various powder mixtures based on alkaline carbonates, NaCl-Na 2 CO 3 , NaCl-Na 2 CO 3 ,H 2 O etc... are studied. An attempt of interpretation on sodium fire extinction is presented [fr

Technical meeting on decommissioning of fast reactors after sodium draining. Working material

International Nuclear Information System (INIS)

2005-01-01

The objective of the technical meeting was to provide a forum for in-depth scientific and technical exchange on topics related to the decommissioning experience with fast reactors, in particular with regard to the decommissioning of components after sodium draining. Accordingly, the scope of the meeting covers the review and analyses of the experience gained from the decommissioning of both active sodium loops and sodium cooled fast reactors (e.g., KNK II, Superphenix, RAPSODIE, EBR-II, FERMI, BN-350, BR-10). It is expected that the outcome of the meeting will contribute to the Agency initiative to preserve fast reactor data and knowledge. The main focus of the technical meeting was given on the decommissioning of both active loop and reactor components (e.g., the primary vessel of a sodium-cooled reactor) that have been drained of sodium, but that still conserve some residual amounts of sodium (e.g., films covering the entire surface of the component, or particular sodium heels that cannot be drained)

Diazepam reduces excitability of amygdala and further influences auditory cortex following sodium salicylate treatment in rats.

Science.gov (United States)

Song, Yu; Liu, Junxiu; Ma, Furong; Mao, Lanqun

2016-12-01

Diazepam can reduce the excitability of lateral amygdala and eventually suppress the excitability of the auditory cortex in rats following salicylate treatment, indicating the regulating effect of lateral amygdala to the auditory cortex in the tinnitus procedure. To study the spontaneous firing rates (SFR) of the auditory cortex and lateral amygdala regulated by diazepam in the tinnitus rat model induced by sodium salicylate. This study first created a tinnitus rat modal induced by sodium salicylate, and recorded SFR of both auditory cortex and lateral amygdala. Then diazepam was intraperitoneally injected and the SFR changes of lateral amygdala recorded. Finally, diazepam was microinjected on lateral amygdala and the SFR changes of the auditory cortex recorded. Both SFRs of the auditory cortex and lateral amygdala increased after salicylate treatment. SFR of lateral amygdala decreased after intraperitoneal injection of diazepam. Microinjecting diazepam to lateral amygdala decreased SFR of the auditory cortex ipsilaterally and contralaterally.

The removal of dinitrochlorobenzene from industrial residuals by liquid-liquid extraction with chemical reaction

Directory of Open Access Journals (Sweden)

G. C. M. Ferreira

2007-09-01

Full Text Available Nitrochlorobenzenes (NCBs are very important in the chemical industry since they have been used as raw material for the manufacture of crop protection products, as active ingredients in the pharmaceutical industry, as pigments and as antioxidants as well as for other uses. In industrial processes, NCBs are produced by monochlorobenzene (MCB nitration reactions and one of the main residuals formed is dinitrochlorobenzene (DNCB, which is mainly composed of the isomer 2,4DNCB. This subproduct, although of commercial interest when in its pure state, is generally incinerated due to the high costs of recovery treatment and purification. The objective of this study is to present an alternative to the treatment of industrial residuals containing DNCB. The technique consists of converting DNCB into sodium dinitrophenolate, which is very soluble in water and is also easy to reuse. For this purpose, liquid-liquid extraction with chemical reaction (alkaline hydrolysis with a rotating disc contactor (RDC is used. Experimental data on MCB nitration reactions as well as alkaline hydrolysis using a rotating disc contactor are presented.

Minimization of Residual Stress in an Al-Cu Alloy Forged Plate by Different Heat Treatments

Science.gov (United States)

Dong, Ya-Bo; Shao, Wen-Zhu; Jiang, Jian-Tang; Zhang, Bao-You; Zhen, Liang

2015-06-01

In order to improve the balance of mechanical properties and residual stress, various quenching and aging treatments were applied to Al-Cu alloy forged plate. Residual stresses determined by the x-ray diffraction method and slitting method were compared. The surface residual stress measured by x-ray diffraction method was consistent with that measured by slitting method. The residual stress distribution of samples quenched in water with different temperatures (20, 60, 80, and 100 °C) was measured, and the results showed that the boiling water quenching results in a 91.4% reduction in residual stress magnitudes compared with cold water quenching (20 °C), but the tensile properties of samples quenched in boiling water were unacceptably low. Quenching in 80 °C water results in 75% reduction of residual stress, and the reduction of yield strength is 12.7%. The residual stress and yield strength level are considerable for the dimensional stability of aluminum alloy. Quenching samples into 30% polyalkylene glycol quenchants produced 52.2% reduction in the maximum compressive residual stress, and the reduction in yield strength is 19.7%. Moreover, the effects of uphill quenching and thermal-cold cycling on the residual stress were also investigated. Uphill quenching and thermal-cold cycling produced approximately 25-40% reduction in residual stress, while the effect on tensile properties is quite slight.

Control system of an anaerobia reactor used in the treatment of the Industrial residual waters

International Nuclear Information System (INIS)

Duque, Mauricio; Giraldo, Eugenio; Bello Frank

1995-01-01

The technology of the anaerobia digestion, has had a wide acceptance in the Colombian means for the treatment of industrial residual waters, especially for the economic advantages that it present and the good purification results. The technology of the anaerobia digestion for the treatment of residual waters, is based in the conversion of the organic matter present in the polluted waters, in methane and carbon dioxide. These two gases are removed of the reactor by means of special structures of gathering. Microorganisms that are sensitive to the changes of the pH mediate the conversion of the organic matter to CH4 and CO2. Therefore, the control on the pH is necessary for a correct behavior of the reactor. At the moment many industries are implementing plans of contamination control, that involve treatment of residual waters for means anaerobia. The present investigation is part of a wide work program in the technology of the anaerobia digestion. It is looked for to develop a monitored system and automatic control of reactors discharge anaerobia appraises, in a combined effort among the departments of Civil and Electric Engineering of the Andes University

Purification of Sodium Phosphates as by Product of Rirang Ore Decomposition Process

International Nuclear Information System (INIS)

Sugeng-Walujo; Hafni-LN; Susilaningtyas; Mukhlis; Budi-Sarono; Widowati

2004-01-01

The aim of this experiment is to get purification condition of sodium phosphates from the filtration result of mixing mother liquor and filtrate of washing residue from Rirang monazite decomposition by alkaline. The method of purification which has been used is dissolved the precipitation of sodium phosphates into agitated water 5 minutes and solution settling for 12 hours until appear of sodium phosphate crystals. The variable of experiment included dissolution time and ratio of the amount precipitate sodium phosphate volume of water to solvent. Experimental data shown that the good temperature of dissolution is 70 o C with the ratio of precipitate sodium phosphate is 80 gram/ 40 ml to water. The recovery of sodium phosphate crystallisation is 87.4314 % with 54.0105 % pure of Na 3 PO 4 , U content is 0.0004%, NaOH content and other impurities is 45.9889%. (author)

Effect of water treatment residuals on soil phosphorus, copper and aluminium availability and toxicity

Energy Technology Data Exchange (ETDEWEB)

Lombi, E., E-mail: enzo.lombi@unisa.edu.a [CSIRO Land and Water, Centre for Environmental Contaminant Research, PMB 2, Glen Osmond, SA 5064 (Australia); Centre for Environmental Risk Assessment and Remediation, University of South Australia, Building X, Mawson Lakes Campus, Mawson Lakes, SA 5095 (Australia); CRC CARE, PO Box 486, Salisbury, SA 5106 (Australia); Stevens, D.P. [CSIRO Land and Water, Centre for Environmental Contaminant Research, PMB 2, Glen Osmond, SA 5064 (Australia); Arris Pty Ltd, PO Box 5143, Burnley, Victoria 3121 (Australia); McLaughlin, M.J. [CSIRO Land and Water, Centre for Environmental Contaminant Research, PMB 2, Glen Osmond, SA 5064 (Australia); Soil and Land Systems, University of Adelaide, PMB 1, Glen Osmond, SA 5064 (Australia)

2010-06-15

Water treatment residuals (WTRs) are produced by the treatment of potable water with coagulating agents. Beneficial recycling in agriculture is hampered by the fact that WTRs contain potentially toxic contaminants (e.g. copper and aluminium) and they bind phosphorus strongly. These issues were investigated using a plant bioassay (Lactuca sativa), chemical extractions and an isotopic dilution technique. Two WTRs were applied to an acidic and a neutral pH soil at six rates. Reductions in plant growth in amended soils were due to WTR-induced P deficiency, rather than Al or Cu toxicity. The release of potentially toxic Al from WTRs was found to be mitigated by their alkaline nature and pH buffering capacity. However, acidification of WTRs was shown to release more soluble Al than soil naturally high in Al. Copper availability was relatively low in all treatments. However, the lability of WTR-Cu increased when the WTR was applied to the soil. - The effect of water treatment residue application to soil was investigated in relation to phosphorus availability, and copper and aluminium phytotoxicity.

Effect of water treatment residuals on soil phosphorus, copper and aluminium availability and toxicity

International Nuclear Information System (INIS)

Lombi, E.; Stevens, D.P.; McLaughlin, M.J.

2010-01-01

Water treatment residuals (WTRs) are produced by the treatment of potable water with coagulating agents. Beneficial recycling in agriculture is hampered by the fact that WTRs contain potentially toxic contaminants (e.g. copper and aluminium) and they bind phosphorus strongly. These issues were investigated using a plant bioassay (Lactuca sativa), chemical extractions and an isotopic dilution technique. Two WTRs were applied to an acidic and a neutral pH soil at six rates. Reductions in plant growth in amended soils were due to WTR-induced P deficiency, rather than Al or Cu toxicity. The release of potentially toxic Al from WTRs was found to be mitigated by their alkaline nature and pH buffering capacity. However, acidification of WTRs was shown to release more soluble Al than soil naturally high in Al. Copper availability was relatively low in all treatments. However, the lability of WTR-Cu increased when the WTR was applied to the soil. - The effect of water treatment residue application to soil was investigated in relation to phosphorus availability, and copper and aluminium phytotoxicity.

Hemodialysis for near-fatal sodium phosphate toxicity in a child receiving sodium phosphate enemas.

Science.gov (United States)

Becknell, Brian; Smoyer, William E; O'Brien, Nicole F

2014-11-01

This study aimed to demonstrate the importance of considering hemodialysis as a treatment option in the management of sodium phosphate toxicity. This is a case report of a 4-year-old who presented to the emergency department with shock, decreased mental status, seizures, and tetany due to sodium phosphate toxicity from sodium phosphate enemas. Traditional management of hyperphosphatemia with aggressive hydration and diuretics was insufficient to reverse the hemodynamic and neurological abnormalities in this child. This is the first report of the use of hemodialysis in a child without preexisting renal failure for the successful management of near-fatal sodium phosphate toxicity. Hemodialysis can safely be used as an adjunctive therapy in sodium phosphate toxicity to rapidly reduce serum phosphate levels and increase serum calcium levels in children not responding to conventional management.

Effect of Long Term Oral Warfarin Sodium Treatment on Bone Mineral Density Scores and Spinal Sagittal Alignment

Directory of Open Access Journals (Sweden)

Kamil Eyvazov

2016-04-01

Full Text Available Objective: The aim of this study was to investigate the effect of long term oral warfarin sodium treatment on bone mineral density (BMD and spinal sagittal alignment. Materials and Methods: Sixty four participants were enrolled for this retrospective study. Participants were divided into two groups-participants who had taken warfarin sodium for at least two years (n=33 and participants who had never taken warfarin sodium (n=31. All of the individuals were evaluated at the same center. Dual X-ray absorptiometry (DXA was used for measuring BMD. Whole spine x-rays were obtained for sagittal assessment and the following parameters were measured: Cervical lordosis, thoracic kyphosis, lumbar lordosis, pelvic incidence, pelvic tilt, sacral slope and sagittal vertical axis (SVA. Results: The mean BMD value was significantly higher in participants who had not taken warfarin sodium compared to participants who had taken warfarin sodium. The differences between the average values were 0.1552 g/cm2 in BMD; 2.1 in T scores; 1.4 in Z scores. On the radiological evaluation of the spine, cervical lordosis was 7.1 degrees lower, lumbar lordosis was 4.7 degrees lower and thoracic kyphosis was 5.3 degrees higher in the patients using drug. C7 plumb line was interchanged forward in the patients using drug. Conclusions: This study shows that warfarin sodium use worsens bone quality in the lumbar region and does not affect bone quality in the femoral region. Furthermore, warfarin sodium use also reduces physiological lordosis and enhances thoracic kyphosis. Consequences of these changes are the likely cause of sagittal spinal anterior imbalance. Long-term oral warfarin sodium use affect bone mineral density and spinal alignment. Our conclusion about giving clear message and show exactly mechanism we need prospective randomized multicentre studies in future. We strongly believe this study will be pioneer for future researches.

Acute Cyanide Poisoning: Hydroxocobalamin and Sodium Thiosulfate Treatments with Two Outcomes following One Exposure Event.

Science.gov (United States)

Meillier, Andrew; Heller, Cara

2015-01-01

Cyanide is rapidly reacting and causes arrest of aerobic metabolism. The symptoms are diffuse and lethal and require high clinical suspicion. Remediation of symptoms and mortality is highly dependent on quick treatment with a cyanide antidote. Presently, there are two widely accepted antidotes: sodium thiosulfate and hydroxocobalamin. These treatments act on different components of cyanide's metabolism. Here, we present two cases resulting from the same source of cyanide poisoning and the use of both antidotes separately used with differing outcomes.

An experience with in-service fabrication and inspection of austenitic stainless steel piping in high temperature sodium system

Energy Technology Data Exchange (ETDEWEB)

Ravi, S., E-mail: sravi@igcar.gov.in; Laha, K.; Sakthy, S.; Mathew, M.D.; Bhaduri, A.K.

2015-04-01

Highlights: • Procedure for changing 304L SS pipe to 316L SS in sodium loop has been established. • Hot leg made of 304L SS was isolated from existing cold leg made of 316LN SS. • Innovative welding was used in joining the new 316L SS pipe with existing 316LN SS. • The old components of 304L SS piping have been integrated with the new piping. - Abstract: A creep testing facility along with dynamic sodium loop was installed at Indira Gandhi Centre for Atomic Research, Kalpakkam, India to assess the creep behavior of fast reactor structural materials in flowing sodium. Type 304L austenitic stainless steel was used in the low cross section piping of hot-leg whereas 316LN austenitic stainless steel in the high cross section cold-leg of the sodium loop. The intended service life of the sodium loop was 10 years. The loop has performed successfully in the stipulated time period. To enhance its life time, it has been decided to replace the 304L piping with 316L piping in the hot-leg. There were more than 300 welding joints involved in the integration of cold-leg with the new 316L hot-leg. Continuous argon gas flow was maintained in the loop during welding to avoid contamination of sodium residue with air. Several innovative welding procedures have been adopted for joining the new hot-leg with the existing cold-leg in the presence of sodium residue adopting TIG welding technique. The joints were inspected for 100% X-ray radiography and qualified by performing tensile tests. The components used in the discarded hot-leg were retrieved, cleaned and integrated in the renovated loop. A method of cleaning component of sodium residue has been established. This paper highlights the in-service fabrication and inspection of the renovation.

Final report on the safety assessment of potassium silicate, sodium metasilicate, and sodium silicate.

Science.gov (United States)

Elmore, Amy R

2005-01-01

Metasilicate, and Sodium Silicate ranged from negligible to severe, depending on the species tested and the molar ratio and concentration tested. Sodium Metasilicate was negative in the local lymph node assay (LLNA), but a delayed-type hypersensitivity response was observed in mice. Potassium Silicate was nonirritating in two acute eye irritation studies in rabbits. Sodium Metasilicate (42.4% H2O) was corrosive to the rabbit eye. Sodium Silicate was a severe eye irritant in some eye irritation studies, but was irritating or nonirritating in others. A skin freshener containing Sodium Silicate was nonirritating. Sodium Metasilicate was nonmutagenic in bacterial cells. Rats given Sodium Silicate (600 and 1200 ppm of added silica) in the drinking water in reproductive studies produced a reduced number of offspring: to 67% of controls at 600 ppm and to 80% of controls at 1200 ppm. Three adult rats injected intratesticularly and subcutaneously with 0.8 mM/kg of Sodium Silicate showed no morphological changes in the testes and no effect on the residual spermatozoa in the ductus deferens. Sodium Metasilicate (37% in a detergent) mixed with water was a severe skin irritant when tested on intact and abraded human skin, but 6%, 7%, and 13% Sodium Silicate were negligible skin irritants to intact and abraded human skin. Sodium Silicate (10% of a 40% aqueous solution) was negative in a repeat-insult predictive patch test in humans. The same aqueous solution of Sodium Silicate was considered a mild irritant under normal use conditions in a study of cumulative irritant properties. The Cosmetic Ingredient Review (CIR) Expert Panel recognized the irritation potential of these ingredients, especially in leave-on products. However, because these ingredients have limited dermal absorption and Sodium Metasilicate is a GRAS direct food substance, the Panel deemed the ingredients safe for use in cosmetic products in the practices of use and concentration described in this safety assessment, when

Forest treatment residues for thermal energy compared with disposal by onsite burning: Emissions and energy return

Science.gov (United States)

Greg Jones; Dan Loeffler; David Calkin; Woodam Chung

2010-01-01

Mill residues from forest industries are the source for most of the current wood-based energy in the US, approximately 2.1% of the nation's energy use in 2007. Forest residues from silvicultural treatments, which include limbs, tops, and small non-commercial trees removed for various forest management objectives, represent an additional source of woody biomass for...

Effect of sodium hypochlorite on typical biofilms formed in drinking water distribution systems.

Science.gov (United States)

Lin, Huirong; Zhu, Xuan; Wang, Yuxin; Yu, Xin

2017-04-01

Human health and biological safety problems resulting from urban drinking water pipe network biofilms pollution have attracted wide concern. Despite the inclusion of residual chlorine in drinking water distribution systems supplies, the bacterium is a recalcitrant human pathogen capable of forming biofilms on pipe walls and causing health risks. Typical drinking water bacterial biofilms and their response to different concentrations of chlorination was monitored. The results showed that the four bacteria all formed single biofilms susceptible to sodium hypochlorite. After 30 min disinfection, biomass and cultivability decreased with increasing concentration of disinfectant but then increased in high disinfectant doses. PMA-qPCR results indicated that it resulted in little cellular damage. Flow cytometry analysis showed that with increasing doses of disinfectant, the numbers of clusters increased and the sizes of clusters decreased. Under high disinfectant treatment, EPS was depleted by disinfectant and about 0.5-1 mg/L of residual chlorine seemed to be appropriate for drinking water treatment. This research provides an insight into the EPS protection to biofilms. Resistance of biofilms against high levels of chlorine has implications for the delivery of drinking water.

Effect of ascorbate ions in DTPA treatment after contamination by mixed plutonium dioxide-sodium burning products

International Nuclear Information System (INIS)

Metivier, H.; Masse, R.; Nolibe, D.; Nenot, J.C.; Lafuma, J.

1977-01-01

Plutonium toxicity problems arising from the use of molten sodium cooled fast breeder reactors involving the accidental mixing and ignition of sodium contaminated by plutonium dioxide have been investigated. The possibility of using the strong reducing agent, ascorbate ion, in order to reduce Pu VI to a chemical form more complexable by DTPA, has been tested using male and female rats. Urine, feces, liver and skeletal measurements of 239 Pu daughter products were carried out. It was shown that the transportable fraction was not significantly modified by the associate ascorbate-DTPA treatment. However the skeletal burden which represents 2.2% with DTPA, reached only 1.6% with ascorbate association and 0.3% with preventive ascorbate injections. Whatever the DTPA ascorbate treatment, the liver burden was not modified significantly. Difference observable only with preventive ascorbate treatment cancels out ascorbate association in order to greatly increase DTPA therapy efficiency, but seems to indicate that the Pu-proteins associations in blood is reduced more easily by ascorbate than association of Pu with local proteins. Ascorbate reduction can also be observed in urinary elimination in that preventive ascorbate, followed by DTPA-ascorbate, leads to a quicker urinary elimination than DTPA or DTPA plus ascorbate post treatment. (U.K.)

Effect of gamma irradiation and sodium hydroxide on cell wall constituents of some agricultural residues

Energy Technology Data Exchange (ETDEWEB)

Almasri, M R [Department of Radiation Agriculture, Atomic Energy Commision, P.O. Box 6091, Damascus, (Syrian Arab Republic)

1995-10-01

The effect of various doses gamma irradiation and different concentrations of NaOH on cell-wall constituents of wheat straw (W.S), cotton seed shell (C.S.S), peanut shell (P.S), soybean shell (S B.S), extracted olive cake (O.C.E) and extracted sunflower of unpeel seeds (S.U.E) were investigated. Results indicated that Na OH in the concentrations at (2,4 and 6%) had significant effects in the crude fiber (C F) content of W.S, P.S and E.U.E, S B.S, C.S.S, O.C.E,respectively. Treating S.U.E, W.S and all other residues with NaOH (2,4 and 6%) respectively, decreased the neutral-detergent fiber (NDF) level. Irradiation dose of 200 kGy decreased C F for all residues, and it reduced the NDF for S.U.E and S B.S. however, lower irradiation dose (150 KGy) was good enough to reduce the NDF for W.S, C.S.S., P.S. and O.C.E. Combined treatment resulted in better effects in reducing the concentrations of the cell-wall constituents. 3 tabs.

Effect of gamma irradiation and sodium hydroxide on cell wall constituents of some agricultural residues

International Nuclear Information System (INIS)

Almasri, M.R.

1995-01-01

The effect of various doses gamma irradiation and different concentrations of NaOH on cell-wall constituents of wheat straw (W.S), cotton seed shell (C.S.S), peanut shell (P.S), soybean shell (S B.S), extracted olive cake (O.C.E) and extracted sunflower of unpeel seeds (S.U.E) were investigated. Results indicated that Na OH in the concentrations at (2,4 and 6%) had significant effects in the crude fiber (C F) content of W.S, P.S and E.U.E, S B.S, C.S.S, O.C.E,respectively. Treating S.U.E, W.S and all other residues with NaOH (2,4 and 6%) respectively, decreased the neutral-detergent fiber (NDF) level. Irradiation dose of 200 kGy decreased C F for all residues, and it reduced the NDF for S.U.E and S B.S. however, lower irradiation dose (150 KGy) was good enough to reduce the NDF for W.S, C.S.S., P.S. and O.C.E. Combined treatment resulted in better effects in reducing the concentrations of the cell-wall constituents. 3 tabs

Influence of treatment by vibration in residual stress generated in the laser welding of HSLA and IF steels

International Nuclear Information System (INIS)

Chuvas, T.C.; Fonseca, M.P. Cindra; Castello, D.A.

2010-01-01

The stress relieving treatment by vibration is a new technology under development, which has many advantages over thermal methods. In this work was analyzed the surface residual stress generated in the laser welding of biphasic HSLA and IF steels, both used in the automotive industry. Residual stresses were measured by X-ray diffraction, by the sen 2 Ψ method. Residual stresses generated in the welding of the samples were tensile at all points measured. After welding, the samples were submitted to the mechanical vibration treatment. Some samples presented a significant reduction in the stress values. The welded joints were also characterized by optical microscopy. (author)

Use of Sodium Hypochlorite for the Control of Bakanae Disease in Rice

Directory of Open Access Journals (Sweden)

Dong Bum Shin

2014-12-01

Full Text Available For application of sodium hypochlorite as a seed disinfectant to the control of bakanae disease caused by Gibberella fujikuroi in rice, we investigated the effects of sodium hypochlorite for antifungal activity, eliminating fungus from seeds and reducing disease occurrence in vitro and greenhouse. The viability of the pathogen was significantly reduced at 80 ml/l concentration of sodium hypochlorite, and the pathogens did not grow at over 100 ml/l concentration of sodium hypochlorite. The effect of eliminating fungus was 90% at treatment of 0.3% sodium hypochlorite solution to infected rice seeds for eight hours. When the rice seeds were soaked into 0.5% and 0.3% sodium hypochlorite solutions for twelve hours, the disease incidences of rice seedling were remarkably reduced to 4.3% and 4.7%, respectively, compared to 97.3% of non-treatment control. The rates of seedling stand were 29.1% and 26.9% higher with the sodium hypochlorite treatment than that of non-treatment control. When prochloraz and sodium hypochlorite was treated to naturally severely infested rice seeds with bakanae disease, the disinfection effect was higher than that of prochloraz alone treatment. When the seeds were soaked in sodium hypochlorite before or after prochloraz, the rate of seed contamination was low as 4.0% or 6.3%, respectively, compared to prochloraz alone as 13.7%. The disease incidence was low as 3.7% or 8.3%, respectively, compared to prochloraz alone as 14.3%. The disinfection effect of treatment with prochloraz after sodium hypochlorite was higher than that of treatment with prochloraz before sodium hypochlorite.

Randomized noninferiority field trial evaluating cephapirin sodium for treatment of nonsevere clinical mastitis.

Science.gov (United States)

Tomazi, T; Lopes, T A F; Masson, V; Swinkels, J M; Santos, M V

2018-05-16

The general objective of this study was to evaluate whether cephapirin sodium is noninferior compared with a positive control broad-spectrum product formulated with a combination of antimicrobials for intramammary treatment of nonsevere clinical mastitis. In addition, we compared the efficacy of treatments on the cure risks of pathogen groups (gram-positive, gram-negative, and cultures with no growth) based on culture results. A total of 346 cows distributed in 31 commercial dairy herds were selected to participate in the study, although only 236 met the criteria for evaluation of microbiological cure. Coagulase-negative staphylococci were the most isolated gram-positive pathogens in pretreatment milk samples, whereas the most common gram-negative bacterium was Escherichia coli. Cows attending the postadmission criteria were treated with 4 intramammary infusions (12 h apart) of one of the following antimicrobials: 300 mg of cephapirin sodium + 20 mg of prednisolone (CS), or the positive control treatment formulated with a combination of antimicrobials (200 mg of tetracycline + 250 mg of neomycin + 28 mg of bacitracin + 10 mg of prednisolone; TNB). Noninferiority analysis and mixed regression models (overall and considering the pathogen groups) were performed for the following outcomes: bacteriological cure (absence of the causative pathogens in cultures performed in milk samples collected at 14 and 21 ± 3 d after enrollment), pathogen cure (absence of any pathogen on both follow-up samples), clinical cure (absence of clinical sign in the milk and mammary gland at 48 h after the last antimicrobial infusion), extended clinical cure (normal milk and normal gland on the second posttreatment sample collection (d 21), and linear score of somatic cell count cure [linear score of somatic cell count recovery (≤4.0) on d 21 ± 3 after enrollment]. No significant differences were observed between treatments regarding any of the evaluated outcomes in both regression models

Regulation of apoptosis in human melanoma and neuroblastoma cells by statins, sodium arsenite and TRAIL: a role of combined treatment versus monotherapy

Science.gov (United States)

Ivanov, Vladimir N.; Hei, Tom K.

2015-01-01

Treatment of melanoma cells by sodium arsenite or statins (simvastatin and lovastatin) dramatically modified activities of the main cell signaling pathways resulting in the induction of heme oxygenase-1 (HO-1) and in a downregulation of cyclooxygenase-2 (COX-2) protein levels. Through heme degradation and the production of carbon monoxide and biliverdin, HO-1 plays a protective role in different scenario of oxidative stress followed by mitochondrial apoptosis. Both sodium arsenite and statins could be efficient inducers of apoptosis in some melanoma cell lines, but often exhibited only modest proapoptotic activity in others, due to numerous protective mechanisms. We demonstrated in the present study that treatment by sodium arsenite or statins with an additional inhibition of HO-1 expression (or activation) caused a substantial upregulation of apoptosis in melanoma cells. Sodium arsenite- or statin-induced apoptosis was independent of BRAF status (wild type versus V600E) in melanoma lines. Monotreatment required high doses of statins (20–40 μM) for effective induction of apoptosis. As an alternative approach, pretreatment of melanoma cells with statin at decreased doses (5–20 μM) dramatically enhanced TRAIL-induced apoptosis, due to suppression of the NF-κB and STAT3-transcriptional targets (including COX-2) and downregulation of cFLIP-L (a caspase-8 inhibitor) protein levels. Furthermore, combined treatment with sodium arsenite and TRAIL or simvastatin and TRAIL efficiently induced apoptotic commitment in human neuroblastoma cells. In summary, our findings on enhancing effects of combined treatment of cancer cells using statin and TRAIL provide the rationale for further preclinical evaluation. PMID:21910007

Hideout of sodium salts in tubesheet crevices: Final report

International Nuclear Information System (INIS)

Brunet, J.P.; Campon, J.L.

1987-07-01

The hideout of sodium hydroxide and sodium chloride in tubesheet crevices was studied in single tube model boilers at CADARACHE. Radioactive Na 24 was used for the measurements. Crevices of 0.2 mm width were empty or packed. A hydraulically expanded crevice and a rolled crevice were also studied. The concentration rate depends on the bulk water concentration but the equilibrium concentration appears to be related only to thermal conditions. The equilibrium value of 25 moles per liter in the crevice was extrapolated, the sodium concentration in the bulk water being in the range of 5 to 50 ppM. This equilibrium will be obtained with an ''integrated pollution'' of 5000 to 10,000 ppM x hours. Flushing produced by the boiler depressurization was shown to be an effective way to remove salt from the crevice. Sodium hydroxide was shown to concentrate even in a residual crevice of few μm width

Pyroprocessing of oxidized sodium-bonded fast reactor fuel - An experimental study of treatment options for degraded EBR-II fuel

Energy Technology Data Exchange (ETDEWEB)

Hermann, S.D.; Gese, N.J. [Separations Department, Idaho National Laboratory, P.O. Box 1625, Idaho Falls, ID 83415 (United States); Wurth, L.A. [Zinc Air Inc., 5314-A US Hwy 2 West, Columbia Falls, MT 59912 (United States)

2013-07-01

An experimental study was conducted to assess pyrochemical treatment options for degraded EBR-II fuel. As oxidized material, the degraded fuel would need to be converted back to metal to enable electrorefining within an existing electro-metallurgical treatment process. A lithium-based electrolytic reduction process was studied to assess the efficacy of converting oxide materials to metal with a particular focus on the impact of zirconium oxide and sodium oxide on this process. Bench-scale electrolytic reduction experiments were performed in LiCl-Li{sub 2}O at 650 C. degrees with combinations of manganese oxide (used as a surrogate for uranium oxide), zirconium oxide, and sodium oxide. In the absence of zirconium or sodium oxide, the electrolytic reduction of MnO showed nearly complete conversion to metal. The electrolytic reduction of a blend of MnO-ZrO{sub 2} in LiCl - 1 wt% Li{sub 2}O showed substantial reduction of manganese, but only 8.5% of the zirconium was found in the metal phase. The electrolytic reduction of the same blend of MnO-ZrO{sub 2} in LiCl - 1 wt% Li{sub 2}O - 6.2 wt% Na{sub 2}O showed substantial reduction of manganese, but zirconium reduction was even less at 2.4%. This study concluded that ZrO{sub 2} cannot be substantially reduced to metal in an electrolytic reduction system with LiCl - 1 wt% Li{sub 2}O at 650 C. degrees due to the perceived preferential formation of lithium zirconate. This study also identified a possible interference that sodium oxide may have on the same system by introducing a parasitic and cyclic reaction of dissolved sodium metal between oxidation at the anode and reduction at the cathode. When applied to oxidized sodium-bonded EBR-II fuel (e.g., U-10Zr), the prescribed electrolytic reduction system would not be expected to substantially reduce zirconium oxide, and the accumulation of sodium in the electrolyte could interfere with the reduction of uranium oxide, or at least render it less efficient.

Effect of shot peening treatment in the behavior of residual stress in duplex stainless steel during medium cycle fatigue

International Nuclear Information System (INIS)

Pedrosa, Peter D.S.; Rebello, Joao Marcos A.; Fonseca, Maria P. Cindra

2010-01-01

The lifetime of duplex stainless steel parts experiencing cyclic fatigue is directly influenced by the residual stresses present in the ferrite and austenite phases. The motivation for this work was to analyze the behaviour of the residual stresses fields introduced by shot peening treatment in both phases, in the sample surface as in the subsurface layers, in low fatigue cycles, using the X-rays diffraction technique. The results shows that the compressive residual stresses introduced by the shot peening treatment in both phases improved fatigue life of the material. However, the cyclical loads produce partial or total relief in these residual stresses fields. It was verified that the shot peening process induced the formation of microcracks only in the ferrite phase. The largest variations in the total compressive residual stresses fields also occurred in this phase. The samples surfaces were analyzed by scanning electron microscopy. (author)

Acute Cyanide Poisoning: Hydroxocobalamin and Sodium Thiosulfate Treatments with Two Outcomes following One Exposure Event

Directory of Open Access Journals (Sweden)

Andrew Meillier

2015-01-01

Full Text Available Cyanide is rapidly reacting and causes arrest of aerobic metabolism. The symptoms are diffuse and lethal and require high clinical suspicion. Remediation of symptoms and mortality is highly dependent on quick treatment with a cyanide antidote. Presently, there are two widely accepted antidotes: sodium thiosulfate and hydroxocobalamin. These treatments act on different components of cyanide’s metabolism. Here, we present two cases resulting from the same source of cyanide poisoning and the use of both antidotes separately used with differing outcomes.

Measurement of heat treatment induced residual stresses by using ESPI combined with hole-drilling method

Directory of Open Access Journals (Sweden)

Jie Cheng

2010-08-01

Full Text Available In this study, residual stresses in heat treated specimen were measured by using ESPI (Electronic Speckle-Pattern Interferometry combined with the hole-drilling method. The specimen, made of SUS 304 austenitic stainless steel, was quenched and water cooled to room temperature. Numerical simulation using a hybrid FDM/FEM package was also carried out to simulate the heat treatment process. As a result, the thermal stress fields were obtained from both the experiment and the numerical simulation. By comparision of stress fields, results from the experimental method and numerical simulation well agreed to each other, therefore, it is proved that the presented experimental method is applicable and reliable for heat treatment induced residual stress measurement.

Dog rose (Rosa canina L.) as a functional ingredient in porcine frankfurters without added sodium ascorbate and sodium nitrite.

Science.gov (United States)

Vossen, Els; Utrera, Mariana; De Smet, Stefaan; Morcuende, David; Estévez, Mario

2012-12-01

The effect of dog rose (Rosa canina L.; RC), rich in polyphenols and ascorbic acid, on lipid and protein oxidation, colour stability and texture of frankfurters was investigated. Four treatments were prepared: with 5 or 30 g/kg RC extract and without sodium ascorbate and sodium nitrite (5RC and 30RC, respectively), a positive control (with sodium ascorbate and sodium nitrite; PC) and a negative control (without sodium ascorbate, sodium nitrite or RC extract; NC). Hexanal values were much higher throughout storage in NC compared to RC and PC frankfurters (Prose can act as a natural antioxidant in frankfurters, but not as full replacer for sodium nitrite. Copyright © 2012 Elsevier Ltd. All rights reserved.

Comparison of enrofloxacin and ceftiofur sodium for the treatment of relapse of undifferentiated fever/bovine respiratory disease in feedlot cattle

Science.gov (United States)

Abutarbush, Sameeh M.; Schunicht, Oliver C.; Wildman, Brian K.; Hannon, Sherry J.; Jim, G. Kee; Ward, Tracy I.; Booker, Calvin W.

2012-01-01

This commercial field trial compared the efficacy of enrofloxacin and ceftiofur sodium in beef cattle at high risk of developing undifferentiated fever (UF), also known as bovine respiratory disease (BRD) that received tilmicosin at feedlot arrival, were diagnosed and initially treated for UF with tilmicosin, and subsequently required a second UF treatment (first relapse). Feedlot cattle (n = 463) were randomly assigned to 2 experimental groups: ENRO or CEF. Second UF relapse, 3rd UF relapse, overall case fatality and BRD case fatality rates were lower in the ENRO group than in the CEF group (P enrofloxacin than ceftiofur sodium for treatment of UF relapse. PMID:22753964

Analysis of trace metals in sodium by flameless atomic absorption spectrophotometry

International Nuclear Information System (INIS)

Mahalingam, T.R.; Geetha, R.; Thiruvengadasamy, A.; Mathews, C.K.

1981-01-01

The estimation of trace metallic impurities in sodium is normally carried out by distilling off the sodium in vacuuum and analysing the residue by atomic absorption spectrophotometry (AAS). This paper describes the direct determination of the following impurities (viz.) Fe, Co, Ni, Cr, Mn, Ca, and Cu in sodium without going through the distillation step. Here sodium is simply dissolved and the solution is subjected to analysis by AAS using flameless atomisation in a graphite furnace. The method of standard additions is employed. Preliminary experiments were carried out to study the matrix effect of sodium on the atomic absorption of cobalt. It has been found that if pyrolysis is done at 1250 0 C for 20 seconds prior to atomisation, the bulk of the sodium nitrate matrix could be successfully removed. The use of the optimum pyrolysis temperatures for the various elements listed above and the matrix interference on the absorbances of these analytes are discussed in this paper. The precision and accuracy of our analytical procedure is also presented. (orig.)

Effect of sodium ascorbate and sodium nitrite on protein and lipid oxidation in dry fermented sausages.

Science.gov (United States)

Berardo, A; De Maere, H; Stavropoulou, D A; Rysman, T; Leroy, F; De Smet, S

2016-11-01

The effects of sodium nitrite and ascorbate on lipid and protein oxidation were studied during the ripening process of dry fermented sausages. Samples were taken at day 0, 2, 8, 14, 21 and 28 of ripening to assess lipid (malondialdehyde) and protein (carbonyls and sulfhydryl groups) oxidation. Sodium ascorbate and nitrite were separately able to reduce the formation of malondialdehyde. Their combined addition resulted in higher amounts of carbonyl compounds compared to their separate addition or the treatment without any of both compounds. Moreover, sodium nitrite limited the formation of γ-glutamic semialdehyde whereas sodium ascorbate showed a pro-oxidant effect. A loss of thiol groups was observed during ripening, which was not affected by the use of sodium ascorbate nor sodium nitrite. In conclusion, sodium nitrite and ascorbate affected protein and lipid oxidation in different manners. The possible pro-oxidant effect of their combined addition on carbonyl formation might influence the technological and sensory properties of these products. Copyright © 2016 Elsevier Ltd. All rights reserved.

Effect of indomethacin, diclofenac sodium and sodium salicylate on peripheral blood cell counts in sublethally gamma-irradiated mice

International Nuclear Information System (INIS)

Pospisil, M.; Netikova, J.; Kozubik, A.; Pipalova, I.

1989-01-01

Treatment with indomethacin and diclofenac sodium was found to increase granulocyte counts in the blood of sublethally gamma-irradiated mice. Treatment with sodium salicylate was ineffective in this respect, administration of sodium salicylate together with indomethacin even decreased the indomethacin-induced effects. The results suggest that the hemopoiesis-stimulating effects of non-steroidal anti-flammatory drugs cannot be correlated with the anti-inflammatory activity but rather with the side effects of these compounds, including the action on gastro-intestinal prostanoid production. This conclusion doubts on the possibility of the usefulness of non-steroidal anti-inflammatory drugs in conditions of the radiation syndrome. (orig.) [de

Effects of post weld heat treatment and weld overlay on the residual stress and mechanical properties in dissimilar metal weld

International Nuclear Information System (INIS)

Campos, Wagner R.C.; Ribeiro, Vladimir S.; Vilela, Alisson H.F.; Almeida, Camila R.O.; Rabello, Emerson G.

2017-01-01

The object of this work is a dissimilar metal weld (DMW) pipe joint between carbon steel (A-106 Gr B) and stainless steel (A-312 TP316L) pipes and filler metals of Nickel alloy (82/182), which find wide application in the field of chemical, oil, petroleum industries, fossil fuel and nuclear power plant. A lot of the failures that have occurred in dissimilar metal welded are affected greatly by residual stresses. Residual stress is often a cause of premature failure of critical components under normal operation of welded components. Several methods have been tested and developed for removing the tensile residual stresses. The aim of the methods is to reduce the tensile stress state or to create compressive stresses at a predefined area, such as the inner surface of a welded pipe joint. Post weld heat treatment (PWHT) and weld overlay (WOL) are two of the residual stress mitigation methods which reduce the tensile residual stress, create compressive stresses and arrest crack initiation and crack growth. The technique used to substantially minimized or eliminated this failure development in the root weld is the post weld heat treatments (stress relief heat treatment) or the weld overlay. In this work was studied the effectiveness in reducing internal residual stress in dissimilar metal welded pipe joints subjected to post weld heat treatment and weld overlay, measurement by hole-drilling strain-gage method of stress relaxation. Also held was mechanical characterization of the welded pipe joint itself. (author)

Effects of post weld heat treatment and weld overlay on the residual stress and mechanical properties in dissimilar metal weld

Energy Technology Data Exchange (ETDEWEB)

Campos, Wagner R.C.; Ribeiro, Vladimir S.; Vilela, Alisson H.F.; Almeida, Camila R.O.; Rabello, Emerson G., E-mail: wrcc@cdtn.br, E-mail: camilarezende.cr@gmail.com, E-mail: egr@cdtn.br, E-mail: vladimirsoler@hotmail.com, E-mail: ahfv02@outlook.com [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

2017-07-01

The object of this work is a dissimilar metal weld (DMW) pipe joint between carbon steel (A-106 Gr B) and stainless steel (A-312 TP316L) pipes and filler metals of Nickel alloy (82/182), which find wide application in the field of chemical, oil, petroleum industries, fossil fuel and nuclear power plant. A lot of the failures that have occurred in dissimilar metal welded are affected greatly by residual stresses. Residual stress is often a cause of premature failure of critical components under normal operation of welded components. Several methods have been tested and developed for removing the tensile residual stresses. The aim of the methods is to reduce the tensile stress state or to create compressive stresses at a predefined area, such as the inner surface of a welded pipe joint. Post weld heat treatment (PWHT) and weld overlay (WOL) are two of the residual stress mitigation methods which reduce the tensile residual stress, create compressive stresses and arrest crack initiation and crack growth. The technique used to substantially minimized or eliminated this failure development in the root weld is the post weld heat treatments (stress relief heat treatment) or the weld overlay. In this work was studied the effectiveness in reducing internal residual stress in dissimilar metal welded pipe joints subjected to post weld heat treatment and weld overlay, measurement by hole-drilling strain-gage method of stress relaxation. Also held was mechanical characterization of the welded pipe joint itself. (author)

On the ASR and ASR thermal residues characterization of full scale treatment plant.

Science.gov (United States)

Mancini, G; Viotti, P; Luciano, A; Fino, D

2014-02-01

In order to obtain 85% recycling, several procedures on Automotive Shredder Residue (ASR) could be implemented, such as advanced metal and polymer recovery, mechanical recycling, pyrolysis, the direct use of ASR in the cement industry, and/or the direct use of ASR as a secondary raw material. However, many of these recovery options appear to be limited, due to the possible low acceptability of ASR based products on the market. The recovery of bottom ash and slag after an ASR thermal treatment is an option that is not usually considered in most countries (e.g. Italy) due to the excessive amount of contaminants, especially metals. The purpose of this paper is to provide information on the characteristics of ASR and its full-scale incineration residues. Experiments have been carried out, in two different experimental campaigns, in a full-scale tyre incineration plant specifically modified to treat ASR waste. Detailed analysis of ASR samples and combustion residues were carried out and compared with literature data. On the basis of the analytical results, the slag and bottom ash from the combustion process have been classified as non-hazardous wastes, according to the EU waste acceptance criteria (WAC), and therefore after further tests could be used in future in the construction industry. It has also been concluded that ASR bottom ash (EWC - European Waste Catalogue - code 19 01 12) could be landfilled in SNRHW (stabilized non-reactive hazardous waste) cells or used as raw material for road construction, with or without further treatment for the removal of heavy metals. In the case of fly ash from boiler or Air Pollution Control (APC) residues, it has been found that the Cd, Pb and Zn concentrations exceeded regulatory leaching test limits therefore their removal, or a stabilization process, would be essential prior to landfilling the use of these residues as construction material. Copyright © 2013 Elsevier Ltd. All rights reserved.

Plant residues--a low cost, effective bioremediation treatment for petrogenic hydrocarbon-contaminated soil.

Science.gov (United States)

Shahsavari, Esmaeil; Adetutu, Eric M; Anderson, Peter A; Ball, Andrew S

2013-01-15

Petrogenic hydrocarbons represent the most commonly reported environmental contaminant in industrialised countries. In terms of remediating petrogenic contaminated hydrocarbons, finding sustainable non-invasive technologies represents an important goal. In this study, the effect of 4 types of plant residues on the bioremediation of aliphatic hydrocarbons was investigated in a 90 day greenhouse experiment. The results showed that contaminated soil amended with different plant residues led to statistically significant increases in the utilisation rate of Total Petroleum Hydrocarbon (TPH) relative to control values. The maximum TPH reduction (up to 83% or 6800 mg kg(-1)) occurred in soil mixed with pea straw, compared to a TPH reduction of 57% (4633 mg kg(-1)) in control soil. A positive correlation (0.75) between TPH reduction rate and the population of hydrocarbon-utilising microorganisms was observed; a weaker correlation (0.68) was seen between TPH degradation and bacterial population, confirming that adding plant materials significantly enhanced both hydrocarbonoclastic and general microbial soil activities. Microbial community analysis using Denaturing Gradient Gel Electrophoresis (DGGE) showed that amending the contaminated soil with plant residues (e.g., pea straw) caused changes in the soil microbial structure, as observed using the Shannon diversity index; the diversity index increased in amended treatments, suggesting that microorganisms present on the dead biomass may become important members of the microbial community. In terms of specific hydrocarbonoclastic activity, the number of alkB gene copies in the soil microbial community increased about 300-fold when plant residues were added to contaminated soil. This study has shown that plant residues stimulate TPH degradation in contaminated soil through stimulation and perhaps addition to the pool of hydrocarbon-utilising microorganisms, resulting in a changed microbial structure and increased alkB gene

Determination of lithium in sodium by vacuum distillation-graphite furnace atomic absorption spectroscopy

International Nuclear Information System (INIS)

Xie Chun; Sun Shiping; Jia Yunteng; Wen Ximeng

1996-12-01

When sodium is used as a coolant in China Experimental Fast Reactor, the lithium content in sodium has an effect on the nuclear property of reactor. A method has been developed to determine the trace lithium in sodium metal at the level of less than ten parts per million. About 0.4 g sodium is placed into a high-purity tantalum crucible, then it is placed in a stainless-steel still to distill at 360 degree C under vacuum (0.01 Pa). After the sodium has been removed, the residue is dissolved by nitric acid (1:2) and analyzed with Graphite Furnace Atomic Absorption Spectroscopy at 671.0 nm wavelength. The distillation conditions, working conditions of the instrument and interferences from matrix sodium, acid and concomitant elements have been studied. Standard addition experiments are carried out with lithium chloride and lithium nitrate. The percentage recoveries are 96.8% and 97.4% respectively. The relative standard deviation is less than +- 5%. The method has been used to determine lithium content in high pure sodium and industrial grade sodium. (11 refs., 5 figs., 5 tabs.)

Repairing an installation and processing the residues

International Nuclear Information System (INIS)

Malet, J.C.; Duverger de Cuy, G.; Sophy, Y.; Cucinotta, A.

1989-01-01

After a sodium leak in a locale, producing a fire, the operator's first concern is to repair the plant. Since the residual sodium and the products of combustion are chemically aggressive, the personnel will have to perform this operation in a hostile environment. This paper presents answers which can be given to the three questions which will however rise: When can the intervention begin? How will it be performed? What should be done with the residues of combustion? This document aims at presenting the different solutions to this problem, these solutions being derived from experiments carried out in France either in the Esmeralda Programme, which is managed jointly by CEA and ENEA, or in the other French programmes. As a general rule, the intervention inside the locale can be made much more easier if: it was foreseen right from the beginning of the design (access under the pipes, anchorage for handling, etc.); the incident can have been localised thanks to the monitoring of locales, enabling the video recording of the first instants, that is, as long as visibility does not fall to zero due to the aerosols from the fire. (author)

Investigation into interaction of mixture of zinc and neodymium nitrates with sodium tungstates in aqueous solutions

Energy Technology Data Exchange (ETDEWEB)

Rozantsev, G M; Krivobok, V I [Donetskij Gosudarstvennyj Univ. (Ukrainian SSR)

1978-09-01

The methods of residual concentrations, pH-potentiometry, and conductometry have been used for studying interaction between the mixture of zinc and neodymium nitrates with sodium tungstate in aqueous solutions. It has been established that independent of the ratio between the components the reaction product is a mixture of simultaneously precipitated zinc and neodymium orthotungstates. Thermal treatment of such mixtures at 650-700 deg C for 40 h and subsequent hardening yields solid solution of the structure ..cap alpha..-Eu/sub 2/(WO/sub 4/)/sub 3/ within the concentration range 85-100 mol % of Nd/sub 2/(WO/sub 4/)/sub 3/.

Amiloride-Sensitive Sodium Channels and Pulmonary Edema

Directory of Open Access Journals (Sweden)

Mike Althaus

2011-01-01

Full Text Available The development of pulmonary edema can be considered as a combination of alveolar flooding via increased fluid filtration, impaired alveolar-capillary barrier integrity, and disturbed resolution due to decreased alveolar fluid clearance. An important mechanism regulating alveolar fluid clearance is sodium transport across the alveolar epithelium. Transepithelial sodium transport is largely dependent on the activity of sodium channels in alveolar epithelial cells. This paper describes how sodium channels contribute to alveolar fluid clearance under physiological conditions and how deregulation of sodium channel activity might contribute to the pathogenesis of lung diseases associated with pulmonary edema. Furthermore, sodium channels as putative molecular targets for the treatment of pulmonary edema are discussed.

Fractional ablative carbon dioxide laser followed by topical sodium stibogluconate application: A treatment option for pediatric cutaneous leishmaniasis.

Science.gov (United States)

Hilerowicz, Yuval; Koren, Amir; Mashiah, Jacob; Katz, Oren; Sprecher, Eli; Artzi, Ofir

2018-05-01

Leishmaniasis is a protozoan zoonotic parasitic infection with cutaneous, mucocutaneous, and visceral manifestations. Israel is endemic for cutaneous leishmaniasis, which is a self-limited disease but is associated with scarring, which is often a source of psychological and social burden for patients. Scars can be especially devastating for children and teenagers. A wide range of physical and medical approaches is used to treat cutaneous leishmaniasis, among which intralesional injections of sodium stibogluconate rank among the most frequently used. Unfortunately, despite being effective, this therapeutic modality can be very painful. Fractional ablative laser creates a controlled mesh-like pattern of tissue ablation in the skin that promotes dermal remodeling and collagen production while at the same time facilitating enhanced delivery of topically applied medications. Patients were treated with fractional ablative carbon dioxide laser followed by immediate topical application of sodium stibogluconate. All children were diagnosed with cutaneous leishmaniasis prior to treatment initiation.. Ten children were treated. One leishmania tropica-positive girl failed to respond. The other nine patients achieved clinical cure and demonstrated good to excellent final cosmesis. Self-rated patient satisfaction and tolerance were high No adverse effects were observed or reported during treatment. Fractional ablative carbon dioxide laser followed by topical sodium stibogluconate application appears to be a safe and promising treatment for cutaneous leishmaniasis infection in children. Future controlled studies are required to validate these findings and compare this technique with traditional approaches. © 2018 Wiley Periodicals, Inc.

Determination of thymine glycol residues in irradiated or oxidized DNA by formation of methylglyceric acid

International Nuclear Information System (INIS)

Schellenberg, K.A.; Shaeffer, J.

1986-01-01

Treatment of DNA solutions with X-irradiation various oxidants including hydrogen peroxide plus ferrous ion, hydrogen peroxide plus copper ion and ascorbate, permanganate, or sonication in the presence of dissolved oxygen all produced varying amounts of thymine glycol residues. After denaturing the DNA with heat, the glycol residues were reduced and labeled at the 6 position with tritium- labeled sodium borohydride. Subsequent reaction with anhydrous methanolic HCl gave a quantitative yield of the methyl ester of methylglyceric acid, which was determined by thin layer chromatography. The method, developed using thymidine as a model, was used to ascertain the requirements for glycol formation in DNA. It was shown that hydroxyl radical generating systems, permanganate, X-irradiation, or sonication in presence of oxygen were required, but hydrogen peroxide in the absence of iron or copper and ascorbate was inactive. Application to determination of DNA damage in vivo is being explored

The effect of reuse of unhairing-liming residual floats through ...

African Journals Online (AJOL)

STORAGESEVER

2008-09-03

Sep 3, 2008 ... Key words: Unhairing-liming process, reusing, leather industry, environment, bacterial and fungal numbers. INTRODUCTION .... 4.0 x101. -: No growth. Chemical analysis of samples. Chemical analyses of sodium sulphide and lime were done for the regeneration of ULP residual liquors. While preparing ...

Sodium retention and insulin treatment in insulin-dependent diabetes mellitus

DEFF Research Database (Denmark)

Nørgaard, K; Feldt-Rasmussen, B

1994-01-01

subcutaneously, contributes to the increased ENa. Three studies were performed. Study 1 was a cross-sectional study comprising 28 type 1 diabetic men (aged 18-35 years) with short-duration diabetes (diabetic complications, and 22 control subjects. Study 2 was a prospective study of 17...... subcutaneous insulin infusion for improvement of glycaemic control or to remain on conventional insulin treatment. In study 1, ENa was higher in short-duration type 1 diabetic men than in controls (3003 +/- 325 vs 2849 +/- 207 mEq/1.73 m2, P ...The hypothesis that total body exchangeable sodium (ENa) is elevated in type 1 (insulin-dependent) diabetic patients with short-duration diabetes and no signs of microangiopathy was tested. Also tested was whether peripheral hyperinsulinaemia, in terms of the amounts of insulin injected...

A negative charge in transmembrane segment 1 of domain II of the cockroach sodium channel is critical for channel gating and action of pyrethroid insecticides

International Nuclear Information System (INIS)

Du Yuzhe; Song Weizhong; Groome, James R.; Nomura, Yoshiko; Luo Ningguang; Dong Ke

2010-01-01

Voltage-gated sodium channels are the primary target of pyrethroids, an important class of synthetic insecticides. Pyrethroids bind to a distinct receptor site on sodium channels and prolong the open state by inhibiting channel deactivation and inactivation. Recent studies have begun to reveal sodium channel residues important for pyrethroid binding. However, how pyrethroid binding leads to inhibition of sodium channel deactivation and inactivation remains elusive. In this study, we show that a negatively charged aspartic acid residue at position 802 (D802) located in the extracellular end of transmembrane segment 1 of domain II (IIS1) is critical for both the action of pyrethroids and the voltage dependence of channel activation. Charge-reversing or -neutralizing substitutions (K, G, or A) of D802 shifted the voltage dependence of activation in the depolarizing direction and reduced channel sensitivity to deltamethrin, a pyrethroid insecticide. The charge-reversing mutation D802K also accelerated open-state deactivation, which may have counteracted the inhibition of sodium channel deactivation by deltamethrin. In contrast, the D802G substitution slowed open-state deactivation, suggesting an additional mechanism for neutralizing the action of deltamethrin. Importantly, Schild analysis showed that D802 is not involved in pyrethroid binding. Thus, we have identified a sodium channel residue that is critical for regulating the action of pyrethroids on the sodium channel without affecting the receptor site of pyrethroids.

Optimization of Residual Stress of High Temperature Treatment Using Genetic Algorithm and Neural Network

Directory of Open Access Journals (Sweden)

M. Susmikanti

2015-12-01

Full Text Available In a nuclear industry area, high temperature treatment of materials is a factor which requires special attention. Assessment needs to be conducted on the properties of the materials used, including the strength of the materials. The measurement of material properties under thermal processes may reflect residual stresses. The use of Genetic Algorithm (GA to determine the optimal residual stress is one way to determine the strength of a material. In residual stress modeling with several parameters, it is sometimes difficult to solve for the optimal value through analytical or numerical calculations. Here, GA is an efficient algorithm which can generate the optimal values, both minima and maxima. The purposes of this research are to obtain the optimization of variable in residual stress models using GA and to predict the center of residual stress distribution, using fuzzy neural network (FNN while the artificial neural network (ANN used for modeling. In this work a single-material 316/316L stainless steel bar is modeled. The minimal residual stresses of the material at high temperatures were obtained with GA and analytical calculations. At a temperature of 6500C, the GA optimal residual stress estimation converged at –711.3689 MPa at adistance of 0.002934 mm from center point, whereas the analytical calculation result at that temperature and position is -975.556 MPa . At a temperature of 8500C, the GA result was -969.868 MPa at 0.002757 mm from the center point, while with analytical result was -1061.13 MPa. The difference in residual stress between GA and analytical results at a temperatureof6500C is about 27 %, while at 8500C it is 8.67 %. The distribution of residual stress showed a grouping concentrated around a coordinate of (-76; 76 MPa. The residuals stress model is a degree-two polynomial with coefficients of 50.33, -76.54, and -55.2, respectively, with a standard deviation of 7.874.

Solubilities of sodium nitrate, sodium nitrite, and sodium aluminate in simulated nuclear waste

International Nuclear Information System (INIS)

Reynolds, D.A.; Herting, D.L.

1984-09-01

Solubilities were determined for sodium nitrate, sodium nitrite, and sodium aluminate in synthetic nuclear waste liquor. Solubilities were determined as a function of temperature and solution composition (concentrations of sodium hydroxide, sodium nitrate, sodium nitrite, and sodium aluminate). Temperature had the greatest effect on the solubilities of sodium nitrate and sodium nitrite and a somewhat lesser effect on sodium aluminate solubility. Hydroxide had a great effect on the solubilities of all three salts. Other solution components had minor effects. 2 references, 8 figures, 11 tables

Effects of thermal treatment on mineralogy and heavy metal behavior in iron oxide stabilized air pollution control residues

DEFF Research Database (Denmark)

Sørensen, Mette Abildgaard; Bender-Koch, C.; Starckpoole, M. M.

2000-01-01

Stabilization of air pollution control residues by coprecipitation with ferrous iron and subsequent thermal treatment (at 600 and 900 °C) has been examined as a means to reduce heavy metal leaching and to improve product stability. Changes in mineralogy and metal binding were analyzed using various...... analytical and environmental techniques. Ferrihydrite was formed initially but transformed upon thermal treatment to more stable and crystalline iron oxides (maghemite and hematite). For some metals leaching studies showed more substantial binding after thermal treatment, while other metals either....... Thermal treatment of the stabilized residues produced structures with an inherently better iron oxide stability. However, the concentration of metals in the leachate generally increased as a consequence of the decreased solubility of metals in the more stable iron oxide structure....

Effect of Applied Stress and Temperature on Residual Stresses Induced by Peening Surface Treatments in Alloy 600

Science.gov (United States)

Telang, A.; Gnäupel-Herold, T.; Gill, A.; Vasudevan, V. K.

2018-04-01

In this study, the effects of applied tensile stress and temperature on laser shock peening (LSP) and cavitation shotless peening (CSP)-induced compressive residual stresses were investigated using neutron and x-ray diffraction. Residual stresses on the surface, measured in situ, were lower than the applied stress in LSP- and CSP-treated Alloy 600 samples (2 mm thick). The residual stress averaged over the volume was similar to the applied stress. Compressive residual stresses on the surface and balancing tensile stresses in the interior relax differently due to hardening induced by LSP. Ex situ residual stress measurements, using XRD, show that residual stresses relaxed as the applied stress exceeded the yield strength of the LSP- and CSP-treated Alloy 600. Compressive residual stresses induced by CSP and LSP decreased by 15-25% in magnitude, respectively, on exposure to 250-450 °C for more than 500 h with 10-11% of relaxation occurring in the first few hours. Further, 80% of the compressive residual stresses induced by LSP and CSP treatments in Alloy 600 were retained even after long-term aging at 350 °C for 2400 h.

Influence of gamma rays irradiation to chlorphyriphos insecticides residues in grapes (vitis vinifera L.)

International Nuclear Information System (INIS)

Chairul, S.M.

2012-01-01

Simulation methods to determination of chlorphyriphos insecticides residue in grapes cause effect gamma rays, was done. Fruits of grapes soaked with chlorpyriphos insecticide solution high level concentrated (100 ppm; 200 ppm; and 300 ppm) for 3 (three minutes). The treatment of the sample was direct of extraction after soaks; extract after storage for one week after soak, and extract after soak after storage for one week after irradiation at 0.5 kGy; 1.0 kGy; and 1.5 kGy dose. Extraction methods using ethyl acetate solvent, and using sodium sulphate as to dryed water level in grapes, and then extractan was injected to chromatography gas use electron capture detector. The result indicated that occur of descent of chlorpyrifos residues from eachs soaked consequence at storage for one week was amount 7,55; 8,42; and 18,88% respectively, while of consequence irradiation of gamma ray at 0,5 kGy doses, will be descent of chlorpyrifos residues in amount 13,90; 19,16; and 52,79% respectively, and at 1,0 kGy doses irradiation will be descent in amount 34,45; 36,15 and 49,79%, respectively. (author)

Performance of mechanical biological treatment of residual municipal waste in Poland

Science.gov (United States)

den Boer, Emilia; Jędrczak, Andrzej

2017-11-01

The number and capacity of mechanical-biological treatment (MBT) plants in Europe increased significantly in the past two decades as a response to the legal obligation to limit the landfilling of biodegradable waste in landfills and to increase recycling and energy recovery from waste. The aim of these plants is to prepare residual municipal waste for recovery and disposal operations, including especially separation and stabilization of the easily biodegradable fraction (the biofraction). The final products of MBP technology are recyclables, stabilate, high calorific fraction which is used for the production of refuse derived fuel (RDF) and the remaining residual fraction. The shares of the output fractions, especially of the recyclables and RDF determine the overall efficiency of MBT technology in diverting waste from landfills. In this paper results of an assessment of one exemplary MBT plant are provided. The analysis was performed within a comparative study in which 20 selected MBT plants in Poland were subject to a detailed analysis, focusing, both at the design parameters as well as operational ones. The selected plant showed relatively higher overall materials recovery efficiency. With the view to circular economy targets, increased automation of the mechanical waste treatment will be required to support achieving high level diversion from landfills. The study reviled that stabilisation of biofraction should be improved by a better control of process conditions, especially moisture content.

Case studies in residual use and energy conservation at wastewater treatment plants

Energy Technology Data Exchange (ETDEWEB)

Stewart, D. [Science Applications International Corp., Los Altos, CA (United States)

1995-06-01

The US Environmental Protection Agency (EPA) and the National Renewable Energy Laboratory (NREL) for the US Department of Energy (DOE) funded a study to document energy conservation activities and their effects on operation costs, regulatory compliance, and process optimization at several wastewater treatment plants (WWTPS). The purpose of this report is to review the efforts of wastewater treatment Facilities that use residuals as fuels. Case histories are presented for facilities that have taken measures to reduce energy consumption during wastewater treatment. Most of the WWTPs discussed in this report have retrofitted existing facilities to achieve energy conservation. The case studies of energy conservation measures found no effects on the facilities` ability to comply with NPDES permits. Indeed, energy conservation activities enhance environmental compliance in several ways.

Effect of sodium fluoride and sodium nitroprouside on Cicer arietinum and Pisum sativum

Directory of Open Access Journals (Sweden)

Naba Kumar Mondal

2016-07-01

Full Text Available In present study, the individual and combine effect of sodium fluoride (NaF and sodium nitroprouside (SNP on germination and biochemical parameters (pigments, sugar, protein, amino acid, and phenol of Bengal gram (Cicer arietinum and peas (Pisum sativum has been studied. After three days of NaF treatment, reductions were observed in percentage of seed germination, root and shoot length, and pigment content with increasing concentration of NaF (1 to 4 mg L-1. Seedlings treated with SNP, both alone and in combination of NaF, showed enhancement in seed germination as well as other growth parameters. NaF-treated seedlings were found to accumulate more soluble sugars and phenols, which were further increased by SNP treatment thereby indicating a synergistic effect of the possible reasons for the ameliorative effects of SNP in seedlings of Pisum sativum growing under NaF stress. Results also demonstrated that SNP application did not show any improvement in both morpho-physiologically and biochemically under sodium fluoride stress condition.

Complete Treatment Versus Residual Lesion - Long-Term Evolution After Acute Coronary Syndrome

Directory of Open Access Journals (Sweden)

Alexandre de Matos Soeiro

Full Text Available Abstract Introduction: A recently published study raised doubts about the need for percutaneous treatment of nonculprit lesions in patients with acute coronary syndromes (ACS. Methods: Retrospective, unicentric, observational study. Objective: To analyze the long-term outcomes in patients undergoing treatment of the culprit artery, comparing those who remained with significant residual lesions in nonculprit arteries (group I versus those without residual lesions in other coronary artery beds (group II. The study included 580 patients (284 in group I and 296 in group II between May 2010 and May 2013. We obtained demographic and clinical data, as well as information regarding the coronary treatment administered to the patients. In the statistical analysis, the primary outcome included combined events (reinfarction/angina, death, heart failure, and need for reintervention. The comparison between groups was performed using the chi-square test and ANOVA. The long-term analysis was conducted with the Kaplan-Meier method, with a mean follow-up of 9.86 months. Results: The mean ages were 63 years in group I and 62 years in group II. On long-term follow-up, there was no significant difference in combined events in groups I and II (31.9% versus 35.6%, respectively, p = 0.76. Conclusion: The strategy of treating the culprit artery alone seems safe. In this study, no long-term differences in combined endpoints were observed between patients who remained with significant lesions compared with those without other obstructions.

The effect of heat treatment on the magnitude and composition of residual gas in sealed silica glass ampoules

Science.gov (United States)

Palosz, W.; Szofran, F. R.; Lehoczky, S. L.

1994-01-01

The residual gas pressure and composition in sealed silica glass ampoules as a function of different treatment procedures has been investigated. The dependence of the residual gas on the outgassing and annealing parameters has been determined. The effects of the fused silica brand, of the ampoule fabrication, and of post-outgassing procedures have been evaluated.

Risks of antibiotic residues in milk following intramammary and intramuscular treatments in dairy sheep.

Science.gov (United States)

Pengov, A; Kirbis, A

2009-04-01

Very few drugs on the market are approved for use in lactating ewes. Veterinarians in the European Union are allowed to prescribe drugs in an off-label manner but are then obligated to assure that residues do not enter the food chain. In case of mastitis treatment in dairy ewes antibiotic preparations designed and authorized for the bovine mammary gland are usually used. Due to inter-species differences, available bovine data cannot be accurately extrapolated for use in the dairy ewe. The objective of the study was therefore to determine appropriate withdrawal periods for ewe's milk following mastitis treatment with two commercial lactating cow products. For the detection of all components standard agar plate diffusion techniques were used. Regardless of the therapy regime and the product used, residues of antibiotics in milk were detected up to 192h after the last infusion. These results indicate that the required withholding periods for ewe's milk are considerably longer than recommended on the label for bovine milk.

Assessment of pesticide residues on selected vegetables of Pakistan

International Nuclear Information System (INIS)

Khan, M.S.; Shah, M.M.

2011-01-01

The present study was conducted to determine the pesticide residues on selected summer vegetables. Five vegetables were grown with three replicates in a split plot randomized complete block design. Pesticides were sprayed on vegetables thrice at regular intervals each after 15 days. At maturity the pesticides residues were extracted from edible and leaf portions using anhydrous sodium sulfate and ethyl acetate while adsorption chromatography technique was used for cleanup. The extracts were subjected to high performance liquid chromatography (HPLC) for separation and analysis of the compounds. Significant differences (p<0.05) were found in the pesticides residues on edible portions whereas highly significant differences (p<0.001) were observed for the leafy portions. The residual level of cypermethrin was highest (16.2 mg kg/sup -1/) in edible portion of bitter gourd, while Lambdacyhalothrin and Mancozeb residues were detected high (4.50 mg kg/sup -1/, 6.26 mg kg/sup -1/) in edible portion of bitter gourd and Cucumber respectively. Cypermethrin residues were high (1.86 mg kg/sup -1/) in Okra leaves. Mancozeb and Lambdacyhalothrin residual level was high (1.23 mg kg/sup -1/, and 0.0002 mg kg/sup -1/) in chili and tomato leaves. Cypermethrin residues were readily detected in edible and leaf portion of the selected vegetables. (author)

Full-scale demonstration of treatment of mechanically separated organic residue in a bioreactor at VAM in Wijster

NARCIS (Netherlands)

Oonk, H.; Woelders, H.

1999-01-01

At the VAM waste treatment company in Wijster a demonstration is in progress of bioreactor technology for the treatment of mechanically separated organic residue (MSOR) of a waste separation plant. This bioreactor is an in situ fermentation cell in which physical, chemical and biological processes

Ultra-high-performance liquid chromatography tandem mass spectrometry determination of GHB, GHB-glucuronide in plasma and cerebrospinal fluid of narcoleptic patients under sodium oxybate treatment

DEFF Research Database (Denmark)

Tittarelli, Roberta; Pichini, Simona; Pedersen, Daniel S

2017-01-01

Sodium oxybate (Xyrem®), the sodium salt of γ- hydroxybutyric acid (GHB), is a first-line treatment of the symptoms induced by type 1 narcolepsy (NT1) and it is highly effective in improving sleep architecture, decreasing excessive daytime sleepiness and the frequency of cataplexy attacks. Using ...

Effect of sodium butyrate treatment on the granule morphology, histamine level and elemental content of the bone marrow-derived mast cell

Energy Technology Data Exchange (ETDEWEB)

Rydzynski, K. [Inst. of Occupational Medicine, Lodz (Poland); Dalen, H. [Bergen Univ. (Norway)

1994-12-31

Mast cells derived from the bone marrow of BALB/c mice (BMMC) were cultures and their growth ceased with sodium butyrate. Sodium butyrate treatment (1 mM, 4 days) caused maturation of the granules, and increased histamine content from approx. 1 pg/cell to 4 pg/cell. X-ray microanalysis revealed that maturation of the granules was accompanied by the increase in relative weight percent of sodium, phosphorus and sulphur, with concomitant decrease in chloride. The sulphur to potassium ratio increased three-fold in butyrate-treated mast cells. The existence of a different elemental composition during mast cell maturation may provide additional parameter for rapid discrimination of mast cell subpopulations. (author). 28 refs, 6 figs.

The structure of the antimicrobial active center of lactoferricin B bound to sodium dodecyl sulfate micelles.

Science.gov (United States)

Schibli, D J; Hwang, P M; Vogel, H J

1999-03-12

Lactoferricin B (LfcinB) is a 25-residue antimicrobial peptide released from bovine lactoferrin upon pepsin digestion. The antimicrobial center of LfcinB consists of six residues (RRWQWR-NH2), and it possesses similar bactericidal activity to LfcinB. The structure of the six-residue peptide bound to sodium dodecyl sulfate (SDS) micelles has been determined by NMR spectroscopy and molecular dynamics refinement. The peptide adopts a well defined amphipathic structure when bound to SDS micelles with the Trp sidechains separated from the Arg residues. Additional evidence demonstrates that the peptide is oriented in the micelle such that the Trp residues are more deeply buried in the micelle than the Arg and Gln residues.

Dialysate sodium and sodium gradient in maintenance hemodialysis: a neglected sodium restriction approach?

OpenAIRE

Munoz Mendoza, Jair; Sun, Sumi; Chertow, Glenn M.; Moran, John; Doss, Sheila; Schiller, Brigitte

2011-01-01

Background. A higher sodium gradient (dialysate sodium minus pre-dialysis plasma sodium) during hemodialysis (HD) has been associated with sodium loading; however, its role is not well studied. We hypothesized that a sodium dialysate prescription resulting in a higher sodium gradient is associated with increases in interdialytic weight gain (IDWG), blood pressure (BP) and thirst.

Effect of meat ingredients (sodium nitrite and erythorbate) and processing (vacuum storage and packaging atmosphere) on germination and outgrowth of Clostridium perfringens spores in ham during abusive cooling.

Science.gov (United States)

Redondo-Solano, Mauricio; Valenzuela-Martinez, Carol; Cassada, David A; Snow, Daniel D; Juneja, Vijay K; Burson, Dennis E; Thippareddi, Harshavardhan

2013-09-01

The effect of nitrite and erythorbate on Clostridium perfringens spore germination and outgrowth in ham during abusive cooling (15 h) was evaluated. Ham was formulated with ground pork, NaNO2 (0, 50, 100, 150 or 200 ppm) and sodium erythorbate (0 or 547 ppm). Ten grams of meat (stored at 5 °C for 3 or 24 h after preparation) were transferred to a vacuum bag and inoculated with a three-strain C. perfringens spore cocktail to obtain an inoculum of ca. 2.5 log spores/g. The bags were vacuum-sealed, and the meat was heat treated (75 °C, 20 min) and cooled within 15 h from 54.4 to 7.2 °C. Residual nitrite was determined before and after heat treatment using ion chromatography with colorimetric detection. Cooling of ham (control) stored for 3 and 24 h, resulted in C. perfringens population increases of 1.46 and 4.20 log CFU/g, respectively. For samples that contained low NaNO2 concentrations and were stored for 3 h, C. perfringens populations of 5.22 and 2.83 log CFU/g were observed with or without sodium erythorbate, respectively. Residual nitrite was stable (p > 0.05) for both storage times. Meat processing ingredients (sodium nitrite and sodium erythorbate) and their concentrations, and storage time subsequent to preparation of meat (oxygen content) affect C. perfringens spore germination and outgrowth during abusive cooling of ham. Copyright © 2013 Elsevier Ltd. All rights reserved.

A randomised controlled trial on the effect of mask choice on residual respiratory events with continuous positive airway pressure treatment.

Science.gov (United States)

Ebben, Matthew R; Narizhnaya, Mariya; Segal, Alan Z; Barone, Daniel; Krieger, Ana C

2014-06-01

It has been found that mask style can affect the amount of continuous positive airway pressure (CPAP) required to reduce an apnoea/hyponoea index (AHI) to mask style to another post titration could affect the residual AHI with CPAP. The purpose of this study was to investigate the differences in residual AHI with CPAP treatment between oronasal and nasal masks. Twenty-one subjects (age mean (M)=62.9, body mass index (BMI) M=29.6 kg/m2) were randomised (14 subjects completed the protocol) to undergo an in-laboratory CPAP titration with either a nasal mask or an oronasal mask. Subjects were then assigned this mask for 3weeks of at-home CPAP use with the optimal treatment pressure determined on the laboratory study (CPAP M=8.4 cm of H2O). At the end of this 3-week period, data were collected from the CPAP machine and the subject was given the other mask to use with the same CPAP settings for the next 3weeks at home (if the nasal mask was given initially, the oronasal one was given later and vice versa). On completion of the second 3-week period, data on residual AHI were again collected and compared with the first 3-week period on CPAP. A Wilcoxon Signed-Rank Test (two-tailed) revealed that residual AHI with CPAP treatment was significantly higher with the oronasal compared with the nasal mask (z = -3.296, pmask, and 50% of the subjects had a residual AHI >10/h in the oronasal mask condition, even though all of these subjects were titrated to an AHI of mask compared with a nasal mask. Switching to an oronasal mask post titration results in an increase in residual AHI with CPAP treatment, and pressure adjustment may be warranted. Copyright © 2014 Elsevier B.V. All rights reserved.

Investigation of effect of post weld heat treatment conditions on residual stress for ITER blanket shield blocks

Energy Technology Data Exchange (ETDEWEB)

Jung, Hun-Chea, E-mail: hcjung@nfri.re.kr [ITER Korea, National Fusion Research Institute, Daejeon (Korea, Republic of); Kim, Sa-Woong [ITER Korea, National Fusion Research Institute, Daejeon (Korea, Republic of); Lee, Yun-Hee [Division of Convergence Technology, Korea Research Institute of Standard and Science (KRISS), Daejeon (Korea, Republic of); Baek, Seung-Wook [Division of Industrial Metrology, Korea Research Institute of Standard and Science (KRISS), Daejeon (Korea, Republic of); Ha, Min-Su; Shim, Hee-Jin [ITER Korea, National Fusion Research Institute, Daejeon (Korea, Republic of)

2016-11-01

Highlights: • PWHT for ITER blanket shield block should be performed for dimensional stability. • Investigation of the effect of PWHT conditions on properties was performed. • Instrumented indentation method for evaluation of properties was used. • Residual stress and hardness decreased with increasing PWHT temperature. • Optimization of PWHT conditions would be needed for satisfaction of requirement. - Abstract: The blanket shield block (SB) shall be required the tight tolerance because SB interfaces with many components, such as flexible support keypads, First Wall (FW) support contact surfaces, FW central bolt, electrical strap contact surfaces and attachment inserts for both FW and Vacuum Vessel (VV). In order to fulfil the tight tolerance requirement, stress relieving shall be performed for dimensional stability after cover welding operation. In this paper, effect of Post Weld Heat Treatment (PWHT) conditions, temperature and holding time, was investigated on the residual stress and hardness. The 316L Stainless Steel (SS) was prepared and welded by manual TIG welding by using filler material with 2.4 mm of diameter. Welded 316L SS plate was machined to prepare the specimen for PWHT. PWHT was implemented at 250, 300, 400 °C for 2 and 3 h (400 °C only) and residual stress after relaxation were determined. The evaluation of residual stress and hardness for each specimen was carried out by instrumented indentation technique. The residual stress and hardness were decreased with increasing the heat treatment temperature and holding time.

Chondroitin sulfate and sodium hialuronate in treatment of the degenerative joint disease in dogs. Clinical and radiological aspects

International Nuclear Information System (INIS)

Melo, E.G.; Rezende, C.M.F.; Gomes, M.G.; Freitas, P.M.; Arias, S.S.A.

2003-01-01

The aim of this study was the evaluation of the effects of chondroitin sulfate and sodium hyaluronate in the knee joint of dogs with experimentally induced degenerative joint disease (DJD). Fifteen mongrel dogs, weighing 18 to 25kg were used. DJD was induced by cranial cruciate ligament (CCL) arthroscopical transection. After three weeks, CCL was repaired by an intrarticular technique, which uses fascia lata. The dogs were then divided into three groups as follows: group I received no other treatment, but the CCL reconstitution, group II received 24mg/animal of chondroitin sulfate/IM every five days, totaling six injections, and group III received 20mg/animal of sodium hyaluronate /IV every five days, totaling three injections. All dogs were examined clinically and radiographically for 90 days after the repairment surgery. The clinical evaluation was performed by assessment of lameness, weight-bearing, limb muscle atrophy and range of motion. The results demonstrated that the group treated with sodium hyaluronate had lower degree of lameness in comparison with other groups. The radiographic evaluation showed marginal osteophytes and subchondral bone sclerosis. These changes were more severe in the group treated with sodium hyaluronate. The better clinical results observed in this group, compared with the others, was probably due to the greater action of the drug in the synovium, decreasing the pain and lameness. Radiographic findings correlated poorly with the clinical signs in the group treated with sodium hyaluronate [pt

Modification of bauxite residue generated in the Bayer process by thermal treatment

International Nuclear Information System (INIS)

Garcia, M.C.S.; Pileggi, R.G.; John, V.M.; Gouvea, D.

2011-01-01

Red mud is the waste generated by the aluminum industry, and as other industrial waste presents complex characteristics with numerous difficulties in handling, as well as being a hazardous material due to its low granulometry, alkalinity and high amount generated. It is a waste with potential high polluter, aggravated by the generally adopted vulnerable disposal form, being this, the disposition of the residue in ponds designed for this purpose. The study and development of sustainable alternatives for the use of sludge, treated as raw materials from other processes, are important tendency and necessary trends in the global context of environmental preservation. This work deals with the thermal treatment as a method of modification of the characteristics of the residue, suggesting the reduction of alkalinity together with the lower leaching of alkaline ions. This approach can be a more reliable and environmentally safe disposal alternatives

Clinical and experimental applications of sodium phenylbutyrate.

Science.gov (United States)

Iannitti, Tommaso; Palmieri, Beniamino

2011-09-01

Histone acetyltransferase and histone deacetylase are enzymes responsible for histone acetylation and deacetylation, respectively, in which the histones are acetylated and deacetylated on lysine residues in the N-terminal tail and on the surface of the nucleosome core. These processes are considered the most important epigenetic mechanisms for remodeling the chromatin structure and controlling the gene expression. Histone acetylation is associated with gene activation. Sodium phenylbutyrate is a histone deacetylase inhibitor that has been approved for treatement of urea cycle disorders and is under investigation in cancer, hemoglobinopathies, motor neuron diseases, and cystic fibrosis clinical trials. Due to its characteristics, not only of histone deacetylase inhibitor, but also of ammonia sink and chemical chaperone, the interest towards this molecule is growing worldwide. This review aims to update the current literature, involving the use of sodium phenylbutyrate in experimental studies and clinical trials.

Analysis of the technical capabilities of DOE sites for disposal of residuals from the treatment of mixed low-level waste

International Nuclear Information System (INIS)

Waters, R.D.; Gruebel, M.M.; Langkopf, B.S.; Kuehne, P.B.

1997-04-01

The US Department of Energy (DOE) has stored or expects to generate over the next five years more than 130,000 m 3 of mixed low-level waste (MLLW). Before disposal, MLLW is usually treated to comply with the land disposal restrictions of the Resource Conservation and Recovery Act. Depending on the type of treatment, the original volume of MLLW and the radionuclide concentrations in the waste streams may change. These changes must be taken into account in determining the necessary disposal capacity at a site. Treatment may remove the characteristic in some waste that caused it to be classified as mixed. Treatment of some waste may, by reduction of the mass, increase the concentrations of some transuranic radionuclides sufficiently so that it becomes transuranic waste. In this report, the DOE MLLW streams were analyzed to determine after-treatment volumes and radionuclide concentrations. The waste streams were reclassified as residual MLLW or low-level or transuranic waste resulting from treatment. The volume analysis indicated that about 89,000 m 3 of waste will require disposal as residual MLLW. Fifteen DOE sites were then evaluated to determine their capabilities for hosting disposal facilities for some or all of the residual MLLW. Waste streams associated with about 90% of the total residual MLLW volume are likely to present no significant issues for disposal and require little additional analysis. Future studies should focus on the remaining waste streams that are potentially problematic by examining site-specific waste acceptance criteria, alternative treatment processes, alternative waste forms for disposal, and pending changes in regulatory requirements

Simultaneous Formation of Artificial SEI Film and 3D Host for Stable Metallic Sodium Anodes.

Science.gov (United States)

Zhang, Di; Li, Bin; Wang, Shuai; Yang, Shubin

2017-11-22

Metallic sodium is a promising anode for sodium-based batteries, owing to its high theoretical capacity (1165 mAh g -1 ) and low potential (-2.714 V vs standard hydrogen electrode). However, the growth of sodium dendrites and the infinite volume change of metallic sodium during sodium striping/plating result in a low Coulombic efficiency and poor cycling stability, generating a safety hazard of sodium-based batteries. Here, an efficient approach was proposed to simultaneously generate an artificial SEI film and 3D host for metallic sodium based on a conversion reaction (CR) between sodium and MoS 2 (4Na + MoS 2 = 2Na 2 S + Mo) at room temperature. In the resultant sodium-MoS 2 hybrid after the conversion reaction (Na-MoS 2 (CR)), the production Na 2 S is homogeneously dispersed on the surface of metallic sodium, which can act as an artificial SEI film, efficiently preventing the growth of sodium dendrites; the residual MoS 2 nanosheets can construct a 3D host to confine metallic sodium, accommodating largely the volume change of sodium. Consequently, the Na-MoS 2 (CR) hybrid exhibits very low overpotential of 25 mV and a very long cycle stability more than 1000 cycles. This novel strategy is promising to promote the development of metal (lithium, sodium, zinc)-based electrodes.

Residue age and tree attractiveness influence efficacy of insecticide treatments against ambrosia beetles (Coleoptera: Curculionidae)

Science.gov (United States)

Management of ambrosia beetles in ornamental nurseries relies, in part, on treatments of insecticides to prevent beetles from boring into trees emitting stress-induced ethanol. However, data on residual efficacy of commonly used pyrethroid insecticides is warranted to gauge the duration that trees ...

Divalproex Sodium for the Treatment of PTSD and Conduct Disordered Youth: A Pilot Randomized Controlled Clinical Trial

Science.gov (United States)

Steiner, Hans; Saxena, Kirti S.; Carrion, Victor; Khanzode, Leena A.; Silverman, Melissa; Chang, Kiki

2007-01-01

We examined the efficacy of divalproex sodium (DVP) for the treatment of PTSD in conduct disorder, utilizing a previous study in which 71 youth were enrolled in a randomized controlled clinical trial. Twelve had PTSD. Subjects (all males, mean age 16, SD 1.0) were randomized into high and low dose conditions. Clinical Global Impression (CGI)…

Determination of radiation dose rates and urinary activity of patients received Sodium Iodide-131 for treatment of differentiated thyroid carcinoma

International Nuclear Information System (INIS)

Beiki, D.; Shahhosseini, S.; Dadashzadeh, S.; Eftekhari, M.; Tayebi, H.; Moosazadeh-Rashti, G.

2004-01-01

Sodium Iodide-131 is administrated for treatment of hyperthyroidism and thyroid cancer. Iodine-131 has multiple routs of excretion (urine, saliva, sweat, milk, feces, exhalation) from the body. Patients receiving Sodium Iodide-131 therapy exposes other persons and the environment to unwanted radiation and contamination. The major sources of radiation dose from administration of Iodine-131 is external radiation , also there is a potential for exposure via contamination.Precautions are necessary to limit the radiation dose to family members, nursing staff and members of public and waste treatment workers to less than 1mSv. Patients received Sodium Iodide-131 may come into close contact with other persons. In order to derive appropriate recommendations, dose rates were measured from the anterior mid-trunk of 29 patients in the upright position with 15 minutes post-dose administration at 3 meters and just before they left the nuclear medicine department at 0.5, 1, and 3 meters. We have also measured urinary iodide excretion in 29 patients to estimate Sodium Iodide-131 urinary excretion pattern in iranian patients. Based on results, the maximum cumulative dose to nursing staff was on third day (leaving day) still less than recommended dose bye ICRP. The cumulative dose family members will be more but regarding the time and distance in close contact it will be also less than recommended dose by ICRP.Radiation dose rate was decreased significantly on third day. The urinary excretion patterns in all patients were similar. The urinary excretion rate-time curve in all patients showed multiple peaks due to retention and redistribution of Iodine-131 or enterohepatic cycle of radioiodinated thyroid hormones, which didn't allow calculation of urinary excretion rate constant. The results also showed that 67 hours post administration of Sodium Iodide-131 about 70% of radiopharmaceutical was excreted through urine, 28% physically decayed or eliminated through other biological

Sodium Fire Demonstration Facility Design and Operation

International Nuclear Information System (INIS)

Cho, Youngil; Kim, Jong-Man; Lee, Jewhan; Hong, Jonggan; Yeom, Sujin; Cho, Chungho; Jung, Min-Hwan; Gam, Da-Young; Jeong, Ji-Young

2014-01-01

Although sodium has good characteristics such as high heat transfer rate and stable nuclear property, it is difficult to manage because of high reactivity. Sodium is solid at the room temperature and it easily reacts with oxygen resulting in fire due to the reaction heat. Thus, sodium must be stored in a chemically stable place, i.e., an inert gas-sealed or oil filled vessel. When a sodium fire occurs, the Na 2 O of white fume is formed. It is mainly composed of Na 2 O 2 , NaOH, and Na 2 CO 3 , ranging from 0.1 to several tens of micrometers in size. It is known that the particle size increases by aggregation during floating in air. Thus, the protection method is important and should be considered in the design and operation of a sodium system. In this paper, sodium fire characteristics are described, and the demonstration utility of outbreak of sodium fire and its extinguishing is introduced. In this paper, sodium fire characteristics and a demonstration facility are described. The introduced sodium fire demonstration facility is the only training device used to observe a sodium fire and extinguish it domestically. Furthermore, the type of sodium fire will be diversified with the enhancement of the utility. It is expected that this utility will contribute to experience in the safe treatment of sodium by the handlers

CSF inflammatory biomarkers responsive to treatment in progressive multiple sclerosis capture residual inflammation associated with axonal damage.

Science.gov (United States)

Romme Christensen, Jeppe; Komori, Mika; von Essen, Marina Rode; Ratzer, Rikke; Börnsen, Lars; Bielekova, Bibi; Sellebjerg, Finn

2018-05-01

Development of treatments for progressive multiple sclerosis (MS) is challenged by the lack of sensitive and treatment-responsive biomarkers of intrathecal inflammation. To validate the responsiveness of cerebrospinal fluid (CSF) inflammatory biomarkers to treatment with natalizumab and methylprednisolone in progressive MS and to examine the relationship between CSF inflammatory and tissue damage biomarkers. CSF samples from two open-label phase II trials of natalizumab and methylprednisolone in primary and secondary progressive MS. CSF concentrations of 20 inflammatory biomarkers and CSF biomarkers of axonal damage (neurofilament light chain (NFL)) and demyelination were analysed using electrochemiluminescent assay and enzyme-linked immunosorbent assay (ELISA). In all, 17 natalizumab- and 23 methylprednisolone-treated patients had paired CSF samples. CSF sCD27 displayed superior standardised response means and highly significant decreases during both natalizumab and methylprednisolone treatment; however, post-treatment levels remained above healthy donor reference levels. Correlation analyses of CSF inflammatory biomarkers and NFL before, during and after treatment demonstrated that CSF sCD27 consistently correlates with NFL. These findings validate CSF sCD27 as a responsive and sensitive biomarker of intrathecal inflammation in progressive MS, capturing residual inflammation after treatment. Importantly, CSF sCD27 correlates with NFL, consistent with residual inflammation after anti-inflammatory treatment being associated with axonal damage.

Alginate/sodium caseinate aqueous-core capsules: a pH-responsive matrix.

Science.gov (United States)

Ben Messaoud, Ghazi; Sánchez-González, Laura; Jacquot, Adrien; Probst, Laurent; Desobry, Stéphane

2015-02-15

Alginate capsules have several applications. Their functionality depends considerably on their permeability, chemical and mechanical stability. Consequently, the creation of composite system by addition of further components is expected to control mechanical and release properties of alginate capsules. Alginate and alginate-sodium caseinate composite liquid-core capsules were prepared by a simple extrusion. The influence of the preparation pH and sodium caseinate concentration on capsules physico-chemical properties was investigated. Results showed that sodium caseinate influenced significantly capsules properties. As regards to the membrane mechanical stability, composite capsules prepared at pH below the isoelectric point of sodium caseinate exhibited the highest surface Young's modulus, increasing with protein content, explained by potential electrostatic interactions between sodium caseinate amino-groups and alginate carboxylic group. The kinetic of cochineal red A release changed significantly for composite capsules and showed a pH-responsive release. Sodium caseinate-dye mixture studied by absorbance and fluorescence spectroscopy confirmed complex formation at pH 2 by electrostatic interactions between sodium caseinate tryptophan residues and cochineal red sulfonate-groups. Consequently, the release mechanism was explained by membrane adsorption process. This global approach is useful to control release mechanism from macro and micro-capsules by incorporating guest molecules which can interact with the entrapped molecule under specific conditions. Copyright © 2014 Elsevier Inc. All rights reserved.

Gas chromatographic determination with electron capture detection of residual ethylene oxide in intraocular lenses

Energy Technology Data Exchange (ETDEWEB)

Kikuchi, H.; Nakamura, A.; Tsuji, K.

1988-01-01

A sensitive method is described to determine trace quantities of ethylene oxide (EO) in EO-sterilized intraocular lenses (IOLs). An IOL is dipped in ethanol containing 0.25 ppm propylene oxide (PO) in a 4 mL vial, 2 drops of freshly distilled hydrobromic acid is added through a septum, and the mixture is warmed at 50/sup 0/C for 24 h. It is then neutralized by vigorous shaking with sodium bicarbonate, dehydrated with anhydrous sodium sulfate, and filtered. The filtrate is injected into a gas chromatograph with electron-capture detection, and the peak height ratio of ethylene bromohydrin/propylene bromohydrin is measured. EO residue is calculated from the calibration curve obtained through a similar procedure with the standard EO/PO solutions. The limit of determination is 0.04 ..mu..g/lens (ca 2.0 ppm). When EO residue levels were determined for IOLs sampled at 3 different aeration periods after stabilization, the authors found that 9 days of aeration was necessary to meet the US Food and Drug Administration proposed limit for EO residue in IOLs.

Aspartic acid 397 in subunit B of the Na+-pumping NADH:quinone oxidoreductase from Vibrio cholerae forms part of a sodium-binding site, is involved in cation selectivity, and affects cation-binding site cooperativity.

Science.gov (United States)

Shea, Michael E; Juárez, Oscar; Cho, Jonathan; Barquera, Blanca

2013-10-25

The Na(+)-pumping NADH:quinone complex is found in Vibrio cholerae and other marine and pathogenic bacteria. NADH:ubiquinone oxidoreductase oxidizes NADH and reduces ubiquinone, using the free energy released by this reaction to pump sodium ions across the cell membrane. In a previous report, a conserved aspartic acid residue in the NqrB subunit at position 397, located in the cytosolic face of this protein, was proposed to be involved in the capture of sodium. Here, we studied the role of this residue through the characterization of mutant enzymes in which this aspartic acid was substituted by other residues that change charge and size, such as arginine, serine, lysine, glutamic acid, and cysteine. Our results indicate that NqrB-Asp-397 forms part of one of the at least two sodium-binding sites and that both size and charge at this position are critical for the function of the enzyme. Moreover, we demonstrate that this residue is involved in cation selectivity, has a critical role in the communication between sodium-binding sites, by promoting cooperativity, and controls the electron transfer step involved in sodium uptake (2Fe-2S → FMNC).

Treatment of Lagoon sludge waste generated from Uranium Conversion Plant

International Nuclear Information System (INIS)

Hwang, D.S.; Oh, J.H.; Lee, K.I.; Choi, Y.D.; Hwang, S.T.; Park, J.H.

2003-01-01

This study investigated the dissolution property of nitrate salts in the desalination process by water and the drying property of residual solid after separating nitrates in a series of processes for the sludge treatment. Desalination was carried out with the adding ratio of water and drying property was analyzed by TG/DTA, FTIR, and XRD. Nitrate salts involved in the sludge were separated over 97 % at the water adding ratio of 2.5. But a small quantity of calcium and sodium nitrate remained in the residue. These were decomposed over 600 deg. C while calcium carbonate, which was a main compound of residual solid, was decomposed into calcium oxide over 750 deg. C. The residual solid has to be decomposed over 800 deg. C to converse uranyl nitrate of six values into the stable U 3 O 8 of four values. As a result of removing the nitrates at the adding ratio of 2.5 and drying the residue over 900 deg. C, volume of the sludge waste decreased over 80 %. (authors)

Influence of post-harvest treatments with fludioxonil and soy lecithin co-application in controlling blue and grey mould and fludioxonil residues in Coscia pears.

Science.gov (United States)

Schirra, M; D'Aquino, S; Migheli, Q; Pirisi, F M; Angioni, A

2009-01-01

The residue levels of fludioxonil (FLU) were determined in Coscia pear following a 1-, 2- or 4-min dip in an aqueous mixture of FLU containing 300 or 100 mg l(-1) (active ingredient, a.i.) at 20 and 50 degrees C, respectively, with or without 2% soy lecithin. The efficacy of heat treatment with water and FLU mixtures was investigated on artificially inoculated pears for the control of post-harvest decay caused by blue (Penicillium expansum Link) and grey (Botrytis cinerea Pers. ex Fr.) mould. Treatment with 300 mg l(-1) FLU at 20 degrees C increased residues significantly when treatment time rose from 1 to 2 min; no further increase was recorded when dip time raised from 2 to 4 min. FLU residue rates were unaffected by treatment time when 300 mg l(-1) a.i. was applied in combination with lecithin at 20 degrees C. While treatment with 100 mg l(-1) a.i. at 50 degrees C for 1 and 2 min resulted in similar residue levels, significantly higher residues were detected when dip time increased from 1 to 4 min. Co-application of lecithin significantly decreased FLU residues with respect to fruit treated with FLU alone. Treatments with FLU at 20 or 50 degrees C effectively controlled decay over 10 days of incubation. While co-application of lecithin did not affect the efficacy of FLU at 300 mg l(-1)and 20 degrees C, treatment efficacy decreased when lecithin was applied in combination with 100 mg l(-1) FLU and 50 degrees C for 4 min and to a greater extent when dip time was 1-2 min.

75 FR 14154 - Notice of Receipt of Several Pesticide Petitions Filed for Residues of Pesticide Chemicals in or...

Science.gov (United States)

2010-03-24

... (LOQ) of 0.05 ppm for total residues of spiroxamine is being submitted. The extraction and hydrolysis... detection (ECD), and convert residues of amitraz to 2,4-DMA by acid and base hydrolysis, respectively. The...-(hydrogen sulfobutanedioate), 1- (C 8 -C 20 linear and branched alkyl) ethers, sodium salts (CAS No. 1079993...

Combining mechanical-biological residual waste treatment plants with grate firing; Kombination MBA mit Rostfeuerung

Energy Technology Data Exchange (ETDEWEB)

Fleck, E. [ABB Umwelttechnik GmbH, Butzbach (Germany)

1998-09-01

The promulgation of the Technical Code on Household Waste obliges the local authorities responsible for waste disposal to review existing and prepare new waste management plans. Given the present state of the art the Code`s limit value for loss due to burning of 5% makes thermal treatment of the residual waste practically compulsory. In preparation of these developments and in order to lower costs in general and be able respond flexibly to customer demands ABB is currently undertaking great efforts to provide thermal residual waste treatment plants with a modular design. [Deutsch] Mit Veroeffentlichung der TASi wurden die entsorgungspflichtigen Gebietskoerperschaften gezwungen, bereits vorhandene Abfall-Wirtschaftsplaene zu ueberarbeiten bzw. neue zu erstellen. Technisch laeuft nach derzeitigem Wissensstand der in der TASi vorgegebene maximale Gluehverlust von 5% darauf hinaus, dass eine thermische Behandlung des Restabfalls zwingend vorgegeben ist. Um hierfuer geruestet zu sein, aber auch um generell Kosten zu senken unf flexibel auf Kundenwuensche eingehen zu koennen, unternimmt ABB grosse Abstrengungen, den Aufbau von Anlagen zur thermischen Restabfallbehandlung modular zu gestalten. (orig./SR)

The Initial Comparison Study of Sodium Lignosulfonate, Sodium Dodecyl Benzene Sulfonate, and Sodium p-Toluene Sulfonate Surfactant for Enhanced Oil Recovery

Science.gov (United States)

Khoirul Anas, Argo; Iman Prakoso, Nurcahyo; Sasvita, Dilla

2018-04-01

Surfactant (surface active agent) exhibit numerous interesting properties that enable their use as additional component in mobilising of residual oil from capillary pore after secondary recovery process using gas injection and water flooding. In this study, Sodium Lignosulfonate (SLS) surfactant was successfully synthesized by applying batch method using lignin from oil palm empty fruit bunches as precursor. Furthermore, its performance in reducing interfacial tension of crude oil and formation water colloidal system was compared with commercial available surfactant including Sodium Dodecyl Benzene Sulfonate (SDBS) and Sodium p-Toluene Sulfonate (SpTS). The synthesized SLS surfactant was characterized by using Fourier Transform Infrared (FTIR) spectroscopy. Meanwhile, its performance in reducing interfacial tension of crude oil and formation water colloidal system was analyzed by using compatibility test, phase behaviour analysis, and interfacial tension (IFT) measurement. The compatibility test shows that SLS, SDBS, and SpTS surfactants were compatible with formation water. In addition, the phase behaviour analysis shows that SLS surfactant was better than SpTS surfactant, while SDBS surfactant generates the highest performance proved by the best microemulsion formation resulted by SDBS. Furthermore, the optimum concentration of SLS, SDBS, and SpTS surfactants in reducing the interfacial tension of crude oil and formation water was 1.0%. The IFT measurement indicates that the performance of SLS with the value of 1.67 mN/m was also better than SpTS surfactant with the value of 3.59 mN/m. Meanwhile, SDBS surfactant shows the best performance with the IFT value of 0.47 mN/m.

Aluminum-Based Water Treatment Residue Reuse for Phosphorus Removal

Directory of Open Access Journals (Sweden)

Lai Yoke Lee

2015-04-01

Full Text Available Aluminum-based water treatment residue (Al-WTR generated during the drinking water treatment process is a readily available recycled material with high phosphorus (P adsorption capacity. The P adsorption capacity of Al-WTR generated from Singapore’s water treatment plant was evaluated with reference to particle size range, adsorption pH and temperature. Column tests, with WTR amendments in sand with and without compost, were used to simulate the bioretention systems. The adsorption rate decreased with increasing WTR sizes. Highest P adsorption capacity, 15.57 mg PO43−-P/g WTR, was achieved using fine WTR particles (>50% particles at less than 0.30 mm. At pH 4, the contact time required to reduce effluent P concentration to below the detectable range was half compared with pH 7 and 9. The adsorption rate observed at 40 ± 2 °C was 21% higher compared with that at 30 ± 2 °C. Soil mixes amended with 10% WTR and compost were able to maintain consistently high (90% total phosphorus (TP removal efficiency at a TP load up to 6.45 g/m3. In contrast, TP removal efficiencies associated with columns without WTR amendment decreased to less than 45% as the TP load increased beyond 4.5 g/m3. The results showed that WTR application is beneficial for enhanced TP removal in bioretention systems.

Chronic Temporomandibular Pain Treatment Using Sodium Diclofenac

OpenAIRE

Kurita Varoli, Fernando; Sato, Sandra; Sucena Pita, Murillo; do Nascimento, Cássio; Pedrazzi, Vinícius

2012-01-01

This study evaluate spontaneous pain after and before administration of sodium diclofenac, isolated or associated to carisoprodol, acetaminophen and caffeine, in chronic temporomandibular disorders (TMD) patients. Were selected eighteen volunteers, both men and women, between 35-70 years of age (mean age 50 years). The inclusion criteria was masticatory muscle pain, and the Research Diagnostic Criteria for Temporomandibular Disorders (RDC/TMD) was used on the diagnose. The selection of treatm...

[Influence of non-sodium restricted diet with diuretics on plasma rennin, renal blood flow and in patients with cirrhotic ascites].

Science.gov (United States)

Zhu, Yin-fang; Gu, Xi-bing; Zhu, Hong-ying; Yang, Xiao-juan; Wang, Dong; Yu, Ping

2013-02-01

To explore influence of sodium restricted diet and non-sodium restricted diet on plasma rennin (PRA), angiotensin II (All), ALD, renal blood flow (RBF) and subside of ascites in patients with cirrhotic ascites. Eighty cases of hepatitis B with cirrhotic ascites were randomly divided into sodium restricted diet group and non-sodium restricted diet group. 39 cases were in non-sodium restricted diet group, taking sodium chloride 6500-8000 mg daily; 41 cases were in sodium restricted diet group, taking sodium chloride 5000 mg daily. Both groups received diuretics furosemide and spironolactone. Blood sodium, urine sodium, PRA, AII, ALD, RBF ascites subsiding were compared after treatment. In non-sodium restricted diet group, blood sodium and urine sodium increased 10 days after treatment compared with those before treatment, and compared with those of sodium restricted diet group 10 days after treatment, P Renal damage induced by low blood sodium after treatment was less in non-sodium restricted diet group than that in sodium restricted diet group, P blood sodium, thus increasing excretion of urine sodium and diuretic effect. It can also decrease levels of PRA, AII and ALD, increase renal blood flow and prevent renal damage induced by low blood sodium and facilitate subsiding of ascites.

Expanded heat treatment to form residual compressive hoop stress on inner surface of zirconium alloy tubing

International Nuclear Information System (INIS)

Megata, Masao

1997-01-01

A specific heat treatment process that introduces hoop stress has been developed. This technique can produce zirconium alloy tubing with a residual compressive hoop stress near the inner surface by taking advantage of the mechanical anisotropy in hexagonal close-packed zirconium crystal. Since a crystal having its basal pole parallel to the tangential direction of the tubing is easier to exhibit plastic elongation under the hoop stress than that having its basal pole parallel to the radial direction, the plastic and elastic elongation can coexist under a certain set of temperature and hoop stress conditions. The mechanical anisotropy plays a role to extend the coexistent stress range. Thus, residual compressive hoop stress is formed at the inner surface where more plastic elongation occurs during the heat treatment. This process is referred to as expanded heat treatment. Since this is a fundamental crystallographic principle, it has various applications. The application to improve PCI/SCC (pellet cladding interaction/stress corrosion cracking) properties of water reactor fuel cladding is promising. Excellent results were obtained with laboratory-scale heat treatment and an out-reactor iodine SCC test. These results included an extension of the time to SCC failure. (author)

Microbial quality of swimming pool water with treatment without disinfection, with ultrafiltration, with UV-based treatment and with chlorination

NARCIS (Netherlands)

Keuten, M.G.A.; Peters, M.C.F.M.; van Dijk, J.C.; van Loosdrecht, Mark C.M.; Rietveld, L.C.

2017-01-01

Swimming pools are traditionally disinfected with a residual disinfectant such as sodium hypochlorite. Nowadays, swimming water without a residual disinfectant is increasingly popular, as can be seen by the growing number of (natural) swimming ponds (Weilandt 2015), but health risks for bathers do

Development of on-line monitoring device to detect the presence/absence of sodium vapor

International Nuclear Information System (INIS)

Wolson, R.D.; McPheeters, C.C.; Kremesec, V.J.; Kolba, V.M.

1983-03-01

A process is being developed by the Sodium Waste Technology Program at ANL-W to remove metallic sodium from scrap and waste. The final step in the process is the removal of residual metallic sodium by evaporation at temperatures up to 482 0 C (900 0 F) and at pressures of about 10 - 2 torr (1.3 Pa). Efficient operation of this process requires that the operators have a method to indicate the completion of the evaporation. This end point would signify when the chamber and scrap and waste is free of metallic sodium. It was determined that a measure of the vacuum was not sufficiently sensitive, and a research effort was undertaken to select an on-line monitoring device. In this effort, three promising methods were reviewed. The use of quadrupole mass spectrometer was recommended and an on-line device was designed for use in a Sodium Process Demonstration (SPD) Plant

Intra-individual comparison of magnesium citrate and sodium phosphate for bowel preparation at CT colonography: Automated volumetric analysis of residual fluid for quality assessment

International Nuclear Information System (INIS)

Bannas, P.; Bakke, J.; Munoz del Rio, A.; Pickhardt, P.J.

2014-01-01

Aim: To perform an objective, intra-individual comparison of residual colonic fluid volume and attenuation associated with the current front-line laxative magnesium citrate (MgC) versus the former front-line laxative sodium phosphate (NaP) at CT colonography (CTC). Materials and methods: This retrospective Health Insurance and Portability and Accountability Act-compliant study had institutional review board approval; informed consent was waived. The study cohort included 250 asymptomatic adults (mean age at index 56.1 years; 124 male/126 female) who underwent CTC screening twice over a 5 year interval. Colon catharsis at initial and follow-up screening employed single-dose NaP and double-dose MgC, respectively, allowing for intra-patient comparison. Automated volumetric analysis of residual colonic fluid volume and attenuation was performed on all 500 CTC studies. Colonic fluid volume <200 ml and mean attenuation between 300–900 HU were considered optimal. Paired t-test and McNemar's test were used to compare differences. Results: Residual fluid volumes <200 ml were recorded in 192 examinations (76.8%) following MgC and in 204 examinations (81.6%) following NaP (p = 0.23). The mean total residual fluid volume was 155 ± 114 ml for MgC and 143 ± 100 ml for NaP (p = 0.01). The attenuation range of 300–900 HU was significantly more frequent for MgC (n = 220, 88%) than for NaP (n = 127, 50.8%; p < 0.001). Mean fluid attenuation was significantly lower for MgC (700 ± 165 HU) than for NaP (878 ± 155 HU; p < 0.001). Concomitant presence of both optimal fluid volume and attenuation was significantly more frequent for MgC 65.2% than for NaP (38%; p < 0.001). Conclusions: Objective intra-individual comparison using automated volumetric analysis suggests that the replacement of NaP by MgC as the front-line laxative for CTC has not compromised overall examination quality. - Highlights: • Automated volumetric analysis provides

Effectiveness of Chlorinated Water, Sodium Hypochlorite, Sodium ...

African Journals Online (AJOL)

This study evaluated the efficacy of chlorinated water, sodium hypochlorite solution, sodium chloride solution and sterile distilled water in eliminating pathogenic bacteria on the surfaces of raw vegetables. Lettuce vegetables were dipped in different concentrations of chlorinated water, sodium hypochlorite solution, sodium ...

Behavioral responses and fluid regulation in male rats after combined dietary sodium deficiency and water deprivation.

Science.gov (United States)

Lucia, Kimberly J; Curtis, Kathleen S

2018-02-01

Most investigators use a single treatment such as water deprivation or dietary sodium deficiency to evaluate thirst or sodium appetite, which underlie behavioral responses to body fluid challenges. The goal of the present experiments was to assess the effects of combined treatments in driving behaviors. Therefore, we evaluated the effect of combined overnight water deprivation and dietary sodium deficiency on water intake and salt intake by adult male rats in 2-bottle (0.5M NaCl and water) tests. Overnight water deprivation alone increased water intake, and 10days of dietary sodium deficiency increased 0.5M NaCl intake, with a secondary increase in water intake. During combined water deprivation and dietary sodium deficiency, water intake was enhanced and 0.5M NaCl was reduced, but not eliminated, suggesting that physiologically relevant behavioral responses persist. Nonetheless, the pattern of fluid intake was altered by the combined treatments. We also assessed the effect of these behaviors on induced deficits in body sodium and fluid volume during combined treatments and found that, regardless of treatment, fluid ingestion partially repleted the induced deficits. Finally, we examined urine volume and sodium excretion during dietary sodium deficiency with or without overnight water deprivation and found that, whether or not rats were water deprived, and regardless of water consumption, sodium excretion was minimal. Thus, the combination of water deprivation and dietary sodium deficiency appears to arouse drives that stimulate compensatory behavioral responses. These behaviors, in conjunction with physiological adaptations to the treatments, underlie body sodium and volume repletion in the face of combined water deprivation and dietary sodium deficiency. Copyright © 2017 Elsevier Inc. All rights reserved.

A hybrid liquid-phase precipitation (LPP) process in conjunction with membrane distillation (MD) for the treatment of the INEEL sodium-bearing liquid waste.

Science.gov (United States)

Bader, M S H

2005-05-20

A novel hybrid system combining liquid-phase precipitation (LPP) and membrane distillation (MD) is integrated for the treatment of the INEEL sodium-bearing liquid waste. The integrated system provides a "full separation" approach that consists of three main processing stages. The first stage is focused on the separation and recovery of nitric acid from the bulk of the waste stream using vacuum membrane distillation (VMD). In the second stage, polyvalent cations (mainly TRU elements and their fission products except cesium along with aluminum and other toxic metals) are separated from the bulk of monovalent anions and cations (dominantly sodium nitrate) by a front-end LPP. In the third stage, MD is used first to concentrate sodium nitrate to near saturation followed by a rear-end LPP to precipitate and separate sodium nitrate along with the remaining minor species from the bulk of the aqueous phase. The LPP-MD hybrid system uses a small amount of an additive and energy to carry out the treatment, addresses multiple critical species, extracts an economic value from some of waste species, generates minimal waste with suitable disposal paths, and offers rapid deployment. As such, the LPP-MD could be a valuable tool for multiple needs across the DOE complex where no effective or economic alternatives are available.

The Use of Sodium Bicarbonate in the Treatment of Acidosis in Sepsis: A Literature Update on a Long Term Debate

Directory of Open Access Journals (Sweden)

Dimitrios Velissaris

2015-01-01

Full Text Available Introduction. Sepsis and its consequences such as metabolic acidosis are resulting in increased mortality. Although correction of metabolic acidosis with sodium bicarbonate seems a reasonable approach, there is ongoing debate regarding the role of bicarbonates as a therapeutic option. Methods. We conducted a PubMed literature search in order to identify published literature related to the effects of sodium bicarbonate treatment on metabolic acidosis due to sepsis. The search included all articles published in English in the last 35 years. Results. There is ongoing debate regarding the use of bicarbonates for the treatment of acidosis in sepsis, but there is a trend towards not using bicarbonate in sepsis patients with arterial blood gas pH>7.15. Conclusions. Routine use of bicarbonate for treatment of severe acidemia and lactic acidosis due to sepsis is subject of controversy, and current opinion does not favor routine use of bicarbonates. However, available evidence is inconclusive, and more studies are required to determine the potential benefit, if any, of bicarbonate therapy in the sepsis patient with acidosis.

The treatment of residual stress in fracture assessment of pressure vessels

International Nuclear Information System (INIS)

Green, D.; Knowles, J.

1992-01-01

The treatment of weld residual stress in the fracture assessment of cylindrical pressure vessels is considered through partitioning the stress into membrane, bending and self-balancing through wall components. The influence of each on fracture behavior is discussed. Stress intensity factor solutions appropriate to each type of stress are presented. Short range, medium range and long range stress categories are identified according to simple rules relating the effect of increasing crack length to stress intensity factor and ligament net stress. Proposals are made on how the stress intensity factor from these stress types may be incorporated into a Kr, Lr based fracture assessment

Adsorption performance of creatinine on dialdehyde nanofibrillated cellulose derived from potato residues.

Science.gov (United States)

Cui, Dongli; Liu, Zehua; Yang, Yaxing; Huang, Rijin; Cheng, Xiaojuan; Fatehi, Pedram; Sun, Bo

2016-01-01

Potato residue is vastly produced in the food industry but it is landfilled. This article describes the treatment of purified cellulose derived from potato residues by a high pressure homogenizer to produce nano-fibrillated cellulose (NFC), which was then oxidized by sodium periodate to prepare dialdehyde nano-fibrillated cellulose (DANFC). The produced NFC and DANFC were characterized by a scanning electron microscope (SEM) and Fourier transform infrared spectroscopy (FTIR). The orthogonal experiment was induced to obtain the maximum degree of oxidation (DO) on DANFC. The results indicated that the optimal conditions were 40°C and pH 3. Alternatively, the isotherm and kinetic studies for the adsorption of creatinine on DANFC with different DOs (70.5 and 88.8%) were investigated, and the experimental results fitted well into Freundlich isotherm model and pseudo second-order kinetic model. The maximum adsorption capacities of DANFCs with the DO of 70.55 and 88.85% were 6.7 and 17.2 mg g(-1) , respectively, which were achieved under the conditions of 37°C and initial creatinine concentration of 100 mg L(-1). © 2015 American Institute of Chemical Engineers.

Impact of sodium chloride on breakfast cereal products

OpenAIRE

Moreau, Lydie

2009-01-01

To reduce the amount of sodium chloride in breakfast cereals without changing their properties, it is necessary to understand the role of this salt. Hence, a model system was developed. This model, composed of native waxy maize starch, glucose and a mixture of amino-acids generated similar colour and residual volatiles after heating compared to commercial breakfast cereals. Systematically designed experiments used this model to study the influence of NaCl concentration (0 % to 5.44 %) on colo...

New therapeutic approaches for equine protozoal myeloencephalitis: pharmacokinetics of diclazuril sodium salts in horses.

Science.gov (United States)

Dirikolu, Levent; Karpiesiuk, Wojciech; Lehner, Andreas F; Hughes, Charlie; Woods, William E; Harkins, John D; Boyles, Jeff; Atkinson, Alfonza; Granstrom, David E; Tobin, Thomas

2006-01-01

Diclazuril is a triazine-based antiprotozoal agent which may have clinical application in the treatment of equine protozoal myeloencephalomyelitis (EPM). In this study, the use of the sodium salt diclazuril to increase the apparent bioavailability of diclazuril for the treatment and prophylaxis of EPM and various other Apicomplexan mediated diseases is described. In this study, diclazuril sodium salt was synthesized and administered to horses as diclazuril sodium salt formulations. The absorption, distribution, and clearance of diclazuril sodium salt in the horse are described. Diclazuril was rapidly absorbed, with peak plasma concentrations occurring at 8-24 hours following an oral mucosal administration of diclazuril sodium salt. The mean oral bioavailability of diclazuril as Clinacox was 9.5% relative to oral mucosal administration of diclazuril sodium salt. Additionally, diclazuril in DMSO administered orally was 50% less bioavailable than diclazuril sodium salt following an oral mucosal administration. It was also shown that diclazuril sodium salt has the potential to be used as a feed additive for the treatment and prophylaxis of EPM and various other Apicomplexan mediated diseases.

Thermal Treatment of Iron Oxide Stabilized APC Residues from Waste Incineration and the Effect on Heavy Metal Binding

DEFF Research Database (Denmark)

Sørensen, Mette Abildgaard; Stackpoole, M.; Bender-Koch, C.

2000-01-01

Iron oxide stabilized APC residues from MSWI were heat treated at 600°C and 900°C. The thermal treatments resulted in a change in product stability by forcing a transformation in the mineralogical structures of the products. The treatments, moreover, simulated somewhat the natural aging processes...

Influence of zeolite treated with sulphuric acid and sodium hydroxide on the coagulation-flocculation process of drainage. Influencia de la zeolita tratada con acido sulfurico y con hidroxido de sodio en el proceso de coagulacion floculacion en aguas superficiales

Energy Technology Data Exchange (ETDEWEB)

Gutierrez Duque, M; Herrera Vasconcelos, T; Laria Piedra, N

1994-01-01

The present paper has had as objective the treatment of natural zeolite from Tasajera with sulfuric acid and sodium hydroxide (residuals acid and basic from the regeneration of cationic and anionic resins of the ''Otto Parallada'' thermoelectric plant) at different times and concentrations, with a further comparison and testing of the effectiveness of the obtained zeolite in respect to the natural one as a coadyuvant of the coagulation-flocculation process in the treatment of superficial water. (Author)

Investigation on reusing water treatment residuals to remedy soil contaminated with multiple metals in Baiyin, China

International Nuclear Information System (INIS)

Wang, Changhui; Zhao, Yuanyuan; Pei, Yuansheng

2012-01-01

Highlights: ► Fe/Al water treatment residuals (FARs) can stabilize As, Pb, Ni, Zn, Cr and Cu. ► FARs cannot stabilize Ba and Cd. ► The properties of FARs and soil affect the FARs’ ability of stabilizing metals. - Abstract: In this work, the remediation of soils contaminated with multiple metals using ferric and alum water treatment residuals (FARs) in Baiyin, China, was investigated. The results of metals fractionation indicated that after the soil was treated with FARs, arsenic (As), lead (Pb), nickel (Ni), zinc (Zn) and copper (Cu) could be transformed into more stable forms, i.e., As bound in crystalline Fe/Al oxides and other metals in the oxidable and residual forms. However, the forms of chromium (Cr) and cadmium (Cd) were unaffected. Interestingly, due to the effect of FARs, barium (Ba) was predominantly transformed into more mobile forms. The bioaccessibility extraction test demonstrated that the FARs reduced the bioaccessibility of As by 25%, followed by Cu, Cr, Zn, Ni and Pb. The bioaccessibility of Cd and Ba were increased; in particular, there was an increase of 41% for Ba at the end of the test. In conclusion, the FARs can be used to remedy soil contaminated with multiple metals, but comprehensive studies are needed before practical applications of this work.

Additive Effect of preservative-free sodium hyaluronate 0.1% in treatment of dry eye syndrome with diquafosol 3% eye drops.

Science.gov (United States)

Hwang, Ho Sik; Sung, Yoon-Mi; Lee, Weon Sun; Kim, Eun Chul

2014-09-01

The aim of this study was to evaluate the treatment effect of diquafosol 3% with preservative-free sodium hyaluronate 0.1% eye drops in dry eye syndrome. In total, 150 patients with dry eye syndrome were divided randomly into 3 groups. Group 1 (50 patients) was treated 4 times daily with preserved sodium hyaluronate 0.1%, group 2 (50 patients) was treated 4 times daily with diquafosol 3%, and group 3 (50 patients) was treated 4 times daily with diquafosol 3% and preservative-free sodium hyaluronate 0.1% eye drops for 3 months. Ocular surface disease index (OSDI) score, tear film break-up time, Schirmer I test, corneal fluorescein staining, and impression cytology were evaluated. There were significant improvements in the OSDI score, tear film break-up time, Schirmer I score, fluorescein and Rose Bengal staining, goblet cell density, and impression cytological findings in groups 2 and 3 compared with those for group 1 in patients with dry eye syndrome at 1, 2, and 3 months (P dry eye syndrome. Preservative-free sodium hyaluronate 0.1% eye drops can increase the effect of diquafosol 3% in dry eye syndrome.

Evaluation tissue dissolution property of 2.5 % Sodium Hypochlorite Prepared by Hydrochloric Acid and Sodium Bicarbonate: An in vitro

Directory of Open Access Journals (Sweden)

Hamid Razavian

2016-08-01

Full Text Available Successful endodontic treatment requires chemical preparation in addition to mechanical preparation. The most common material for chemical preparations is sodium hypochlorite. One way to reduce the effects of pH adjustment is the use of sodium hypochlorite. The present paper was conducted to examine the effect of dilution with hydrochloric acid and sodium bicarbonate and reduce pH on ability of tissue solubility of sodium hypochlorite. The present study was conducted in vitro on bovine muscle tissue. Ability of tissue solubility was conducted in four groups respectively with active ingredient including 1 sodium hypochlorite diluted with distilled water 2 sodium hypochlorite diluted with sodium bicarbonate 3 sodium hypochlorite diluted with hydrochloric acid and finally 4 distilled water (control group. Each sample was firstly weighed and then placed in contact with 10 m/L solution for 60 minutes (five 12 -minute intervals. The sample was weighted every five minutes and solution was renewed. The results were analyzed using SPSS-21 Software based on variance analysis, Tukey and T-test (α=0.05. The findings showed that there was significant difference between first, second and third groups in terms of ability of tissue solubility. However, the tissue solubility in second and third groups was lower than first group and it was similar in second and third groups (P Value <0.001. Reduction of sodium bicarbonate PH using sodium hypochlorite and hydrochloric acid reduces ability of tissue solubility in sodium hypochlorite.

Molecular and kinetic determinants of local anaesthetic action on sodium channels.

Science.gov (United States)

French, R J; Zamponi, G W; Sierralta, I E

1998-11-23

(1) Local anaesthetics (LA) rely for their clinical actions on state-dependent inhibition of voltage-dependent sodium channels. (2) Single, batrachoxin-modified sodium channels in planar lipid bilayers allow direct observation of drug-channel interactions. Two modes of inhibition of single-channel current are observed: fast block of the open channels and prolongation of a long-lived closed state, some of whose properties resemble those of the inactivated state of unmodified channels. (3) Analogues of different parts of the LA molecule separately mimic each blocking mode: amines--fast block, and water-soluble aromatics--closed state prolongation. (4) Interaction between a mu-conotoxin derivative and diethylammonium indicate an intrapore site of fast, open-state block. (5) Site-directed mutagenesis studies suggest that hydrophobic residues in transmembrane segment 6 of repeat domain 4 of sodium channels are critical for both LA binding and stabilization of the inactivated state.

Dimethyl sulfoxide and sodium bicarbonate in the treatment of refractory cancer pain.

Science.gov (United States)

Hoang, Ba X; Tran, Dao M; Tran, Hung Q; Nguyen, Phuong T M; Pham, Tuan D; Dang, Hong V T; Ha, Trung V; Tran, Hau D; Hoang, Cuong; Luong, Khue N; Shaw, D Graeme

2011-01-01

Pain is a major concern of cancer patients and a significant problem for therapy. Pain can become a predominant symptom in advanced cancers. In this open-label clinical study, the authors have treated 26 cancer patients who have been declared as terminal without the option of conventional treatment. These patients suffered from high levels of pain that was poorly managed by all available interventional approaches recommended by World Health Organization (WHO) guideline. The results indicate that intravenous infusion of dimethyl sulfoxide (DMSO) and sodium bicarbonate (SB) solution can be a viable, effective, and safe treatment for refractory pain in cancer patients. These patients had pain due to the disease progression and complication of chemotherapy and radiation. Moreover, the preliminary clinical outcome of 96-day follow-up suggests that the application of DMSO and SB solution intravenously could lead to better quality of life for patients with nontreatable terminal cancers. The data of this clinical observation indicates that further research and application of the DMSO and SB combination may help the development of an effective, safe, and inexpensive therapy to manage cancer pain.

Assessment of residual error for online cone-beam CT-guided treatment of prostate cancer patients

International Nuclear Information System (INIS)

Letourneau, Daniel; Martinez, Alvaro A.; Lockman, David; Yan Di; Vargas, Carlos; Ivaldi, Giovanni; Wong, John

2005-01-01

Purpose: Kilovoltage cone-beam CT (CBCT) implemented on board a medical accelerator is available for image-guidance applications in our clinic. The objective of this work was to assess the magnitude and stability of the residual setup error associated with CBCT online-guided prostate cancer patient setup. Residual error pertains to the uncertainty in image registration, the limited mechanical accuracy, and the intrafraction motion during imaging and treatment. Methods and Materials: The residual error for CBCT online-guided correction was first determined in a phantom study. After online correction, the phantom residual error was determined by comparing megavoltage portal images acquired every 90 deg. to the corresponding digitally reconstructed radiographs. In the clinical study, 8 prostate cancer patients were implanted with three radiopaque markers made of high-winding coils. After positioning the patient using the skin marks, a CBCT scan was acquired and the setup error determined by fusing the coils on the CBCT and planning CT scans. The patient setup was then corrected by moving the couch accordingly. A second CBCT scan was acquired immediately after the correction to evaluate the residual target setup error. Intrafraction motion was evaluated by tracking the coils and the bony landmarks on kilovoltage radiographs acquired every 30 s between the two CBCT scans. Corrections based on soft-tissue registration were evaluated offline by aligning the prostate contours defined on both planning CT and CBCT images. Results: For ideal rigid phantoms, CBCT image-guided treatment can usually achieve setup accuracy of 1 mm or better. For the patients, after CBCT correction, the target setup error was reduced in almost all cases and was generally within ±1.5 mm. The image guidance process took 23-35 min, dictated by the computer speed and network configuration. The contribution of the intrafraction motion to the residual setup error was small, with a standard deviation of

Sodium Hypochlorite-Modified Hemosorbents in the Treatment of Limb Ischemia-Reperfusion Syndrome: Experimental Study

Directory of Open Access Journals (Sweden)

V. I. Sergiyenko

2007-01-01

Full Text Available Objective: to enhance the efficiency of treatment for limb ischemia-reperfusion syndrome in an experiment, by using the modified hemosorbents that have oxidative properties.Materials and methods. The investigation was conducted on 94 mongrel male dogs divided into 3 groups: 1 intact animals (n=20; 2 animals treated with hemocarboperfusion on the standard sorbent CKH-1K (n=36; 3 animals received hemocarboperfusion on sodium hypochloride-modified sorbent CKH-1K (n=38. A model of acute ischemia-reperfusion syndrome was created by the method of V. D. Pasechnikov et al. Partial oxygen tension (pO2 was determined by pin polarography. The levels of vasoactive eicosanoids were measured by enzyme immunoassay.Results. In the animals with leg ischemia syndrome, there is a significant pO2 reduction in the muscles of the hip and shin, which does not completely recover after reperfusion. Standard CKN-1K sorbent hemocarboperfusion reduces pO2 as compared with the reperfusion period while the use of modified CKH-1K hemosorbent increased pO2 in the study hind limb muscles to the level observed in intact animals. The development of ischemia and reperfusion is accompanied by the elevated levels of inflammatory mediators that have vasoconstrictive properties (thromboxane B2, endothelin-1, leukotrienes C4/D4/E4 and the lower concentration of the vasodilator prostacyclin. Standard CKN-1K sorbent hemocarboperfusion results in a further increase in the concentrations of thromboxane B2 and leukotrienes C4/D4/E4, a decrease in the concentration of endothelin-1, and an elevation of the levels of prostacyclin and prostaglandin E2. When sodium hypochlorite-modified CKN-1K sorbent hemocarboperfusion is employed, the concentrations of thromboxane B2, endothelin-1, and leukotrienes C4/D4/E4 decrease, and the level of prostacyclin increases.Conclusion. Hemocarboperfusion used in the treatment of leg ischemia-reperfusion syndrome leads to restoration of tissue oxygenation and

Conservative treatment of immature teeth with apical periodontitis using triple antibiotic paste disinfection

OpenAIRE

Wang, Hsin-Ju; Chen, Yea-Huey Melody; Chen, Kuan-Liang

2016-01-01

The purpose of this report is to present conservative treatment for two immature premolars with apical periodontitis. A triple antibiotic paste was used to disinfect the root canal systems for revascularization. In both cases, residual vital pulp tissue was noted in the root canal system after the opening of each premolar. The canals in both cases were irrigated with copious sodium hypochlorite solution and medicated with a paste consisting of ciprofloxacin, metronidazole, and minocycline. Th...

Sodium coolant of fast reactors: Experience and problems

International Nuclear Information System (INIS)

Kozlov, F.A.; Volchkov, L.G.; Drobyshev, A.V.; Nikulin, M.P.; Kochetkov, L.A.; Alexeev, V.V.

1997-01-01

In present report the following subjects are considered: state of the coolant and sodium systems under normal operating condition as well as under decommissioning, disclosing of sodium circuits and liquidation of its consequences, cleaning from sodium and decontamination under repairing works of equipment and circuits. Cleaning of coolant and sodium systems under normal operating conditions and under accident contamination. Cleaning of the equipment under repairing works and during decommissioning from sodium and products of its interaction with water and air. Treatment of sodium waste, taking into account a possibility of sodium fires. It is shown that the state of coolant, cover gas, surfaces of constructive materials which are in contact with them, cleaning systems, formed during installation operation require development of specific technologies. Developed technologies ensured safety operation of sodium cooled installations as in normal operating conditions so in abnormal situations. R and D activities in this field and experience gained provided a solid base for coping with problems arising during decommissioning. Prospective research problems are emphasized where the future efforts should be concentrated in order to improve characteristics of sodium cooled reactors and to make their decommissioning optimal and safe. (author)

Treatment of the acid mine drainage residue for uranium recovery

International Nuclear Information System (INIS)

Dias, M.M.; Horta, D.G.; Fukuma, H.T.; Villegas, R.A.S.; Carvalho, C.H.T. de; Silva, A.C. da

2017-01-01

Acid mine drainage (AMD) is a process that occurs in many mining that have sulfide ores. With water and oxygen, several metals are oxidized, one example being uranium. At the mine pit of the Osamu Utsumi Mine located at INB - Caldas and in two other boot-wastes (mining waste pile), AMD is present and currently, without a technological solution. The acidic water present in the pit is treated with hydrated lime, generating water for disposal and an alkaline residue called calcium diuranate - DUCA. The DUCA has a concentration of approximately 0.32% U 3 O 8 , which makes interesting the development of a process for extracting that metal. One of the processes that can be used is leaching. For this study, it was decided to evaluate the alkaline leaching to extract the uranium present in the residue. It is necessary to optimize operational parameters for the process: percentage of solids, concentration of leaching agent in solution, temperature and reaction time. With these parameters, it is possible to improve the leaching so that the largest amount of uranium is extracted from the sample, to help solve the environmental impact caused by the wastewater from the treatment of acid waters and, in addition, to give an economical destination for this metal that is contained in the deposited DUCA

Characterization and analyses on micro-hardness, residual stress and microstructure in laser cladding coating of 316L stainless steel subjected to massive LSP treatment

Energy Technology Data Exchange (ETDEWEB)

Luo, K.Y.; Jing, X.; Sheng, J. [School of Mechanical Engineering, Jiangsu University, Zhenjiang, 212013 (China); Sun, G.F. [School of Mechanical Engineering, Southeast University, Nanjing, 211189 (China); Yan, Z. [School of Mechanical Engineering, Jiangsu University, Zhenjiang, 212013 (China); Lu, J.Z., E-mail: jzlu@ujs.edu.cn [School of Mechanical Engineering, Jiangsu University, Zhenjiang, 212013 (China)

2016-07-15

The effects of massive laser shock peening (LSP) treatment on micro-hardness, residual stress and microstructure in four different zones of laser cladding coating was investigated. Furthermore, micro-hardness curves and residual stress distributions with and without massive LSP treatment were presented and compared, and typical microstructure in different zones of both coatings were characterized by transmission electron microscope (TEM) and cross-sectional optical microscope (OM) observations. Results and analyses showed that massive LSP treatment had an important influence on micro-hardness and residual stress of the cladding coating. Special attempt was made to the effects of massive LSP treatment on microstructure in three zones of the cladding coating. In addition, the underlying mechanism of massive LSP treatment on microstructure and mechanical properties of the cladding coating was revealed clearly. - Highlights: • Micro-hardness and residual stress curves of both coatings were presented and compared. • Typical microstructure in different zones of both coatings were characterized and analyzed. • LSP causes increased micro-activities, and induces plastic deformation layer in three zones. • Underlying mechanism of LSP on mechanical properties of cladding coating was revealed.

Comprehensive reuse of drinking water treatment residuals in coagulation and adsorption processes.

Science.gov (United States)

Jung, Kyung-Won; Hwang, Min-Jin; Park, Dae-Seon; Ahn, Kyu-Hong

2016-10-01

While drinking water treatment residuals (DWTRs) inevitably lead to serious problems due to their huge amount of generation and limitation of landfill sites, their unique properties of containing Al or Fe contents make it possible to reuse them as a beneficial material for coagulant recovery and adsorbent. Hence, in the present study, to comprehensively handle and recycle DWTRs, coagulant recovery from DWTRs and reuse of coagulant recovered residuals (CRs) were investigated. In the first step, coagulant recovery from DWTRs was conducted using response surface methodology (RSM) for statistical optimization of independent variables (pH, solid content, and reaction time) on response variable (Al recovery). As a result, a highly acceptable Al recovery of 97.5 ± 0.4% was recorded, which corresponds to 99.5% of the predicted Al recovery. Comparison study of recovered and commercial coagulant from textile wastewater treatment indicated that recovered coagulant has reasonable potential for use in wastewater treatment, in which the performance efficiencies were 68.5 ± 2.1% COD, 97.2 ± 1.9% turbidity, and 64.3 ± 1.0% color removals at 50 mg Al/L. Subsequently, in a similar manner, RSM was also applied to optimize coagulation conditions (Al dosage, initial pH, and reaction time) for the maximization of real cotton textile wastewater treatment in terms of COD, turbidity, and color removal. Overall performance revealed that the initial pH had a remarkable effect on the removal performance compared to the effects of other independent variables. This is mainly due to the transformation of metal species form with increasing or decreasing pH conditions. Finally, a feasibility test of CRs as adsorbent for phosphate adsorption from aqueous solution was conducted. Adsorption equilibrium of phosphate at different temperatures (10-30 °C) and initial levels of pH (3-11) indicated that the main mechanisms of phosphate adsorption onto CRs are endothermic and chemical

Sodium Dichromate Barrel Landfill expedited response action proposal

International Nuclear Information System (INIS)

1993-09-01

The US Environmental Protection Agency (EPA) and Washington State Department of Ecology (Ecology) recommended that the US Department of Energy (DOE) prepare an expedited response action (ERA) for the Sodium Dichromate Barrel Landfill. The Sodium Dichromate Barrel Disposal Site was used in 1945 for disposal of crushed barrels. The site location is the sole waste site within the 100-IU-4 Operable Unit. The Waste Information Data System (WIDS 1992) assumes that the crushed barrels contained 1% residual sodium dichromate at burial time and that only buried crushed barrels are at the site. Burial depth is shallow since visual inspection finds numerous barrel debris on the surface. A non-time-critical ERA proposal includes preparation of an engineering evaluation and cost analysis (EE/CA) section. The EE/CA is a rapid, focused evaluation of available technologies using specific screening factors to assess feasibility, appropriateness, and cost. The ERA goal is to reduce the potential for any contaminant migration from the landfill to the soil column, groundwater, and Columbia River. Since the landfill is the only waste site within the operable unit, the ERA will present a final remediation of the 100-IU-4 operable unit

Treatment of mine water and solid residues (RS) in San Rafael mining and milling complex

International Nuclear Information System (INIS)

Asenjo, Armando R.; Perrino, Juan F.

2006-01-01

San Rafael Mining and Milling Complex is located in Mendoza Province, in San Rafael Department, 38 km West from San Rafael city and 240 km south from Mendoza city, capital of the province. Activities related with yellow cake production were performed from 1979 to 1999. Nowadays the mine and the plant are in stand by. At the moment technical, economic and environmental studies are being done in order to restart the activities. Different kind of residues are accumulated in the site: a) Tailing; b) Sludges; c) Low grade ores; e) Waste rock; f) Mine water; g) Solid residues (RS). In this paper methodology to treat mine water and solid residues (RS) will be informed. a) Mine water: 800.000 m 3 of mine water are accumulated in different open pit. Uranium, radium and arsenic are the main ions to take into account to treat the water. Several laboratory and pilot test have been performed in order to define the treatment of the water, according with the regulatory requirement. A methodology using anion exchange resin to fix uranium and precipitation using barium chloride and iron sulfate to separate radium and arsenic has been developed. b) Solid residues (RS): these residues (precipitates) have been produced by neutralization of effluents in a nuclear purification process (TBP process). They are accumulated in drums. These residues come from Cordoba plant, a factory which produces UO 2 powder. The total content of uranium in the precipitate is 14.249 kg with an average uranium concentration of 1,33%. A methodology using sulfuric acid dissolution of the precipitates and anion exchange resin to recovery the uranium has been developed. (author) [es

Sodium Thiosulfate for Recovery of Bond Strength to Dentin Treated with Sodium Hypochlorite.

Science.gov (United States)

Pimentel Corrêa, Ana Carolina; Cecchin, Doglas; de Almeida, José Flávio Affonso; Gomes, Brenda Paula Figueiredo de Almeida; Zaia, Alexandre Augusto; Ferraz, Caio Cezar Randi

2016-02-01

The aim of this study was to evaluate the efficacy of sodium thiosulfate (Na2S2O3) for restoring adhesion to pulp chamber dentin treated with sodium hypochlorite (NaOCl) and EDTA. Sixty-three crowns of bovine incisors were cut to expose the dentin pulp chamber. The specimens were polished and randomly distributed into 9 groups (n = 7) according to the following protocols used: 0.9% sodium chloride for 30 minutes (negative control), 5.25% NaOCl for 30 minutes, 17% EDTA for 3 minutes, and 5.25% NaOCl for 1 minute (positive control). The other groups, after treatments with NaOCl and EDTA, were immersed in 0.5% or 5% Na2S2O3 for 1, 5, and 10 minutes or just immersed in an inert solution for 10 minutes (0.9% sodium chloride). After drying the specimens, Scotchbond Multi-Purpose (3M ESPE, St Paul, MN) was applied to the pulp chamber dentin followed by Filtek Z250 composite (3M ESPE). Six rectangular slabs were obtained from each specimen, and the dentin/resin interface was tested by using a universal testing machine. The resulting data were submitted to 1-way analysis of variance and the Duncan test (P = .05). There was a significant decrease in bond strength regarding NaOCl and EDTA (P adhesive restorations to be immediately applied after endodontic treatment. Copyright © 2016 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

40 CFR 180.1176 - Sodium bicarbonate; exemption from the requirement of a tolerance.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Sodium bicarbonate; exemption from the requirement of a tolerance. 180.1176 Section 180.1176 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Exemptions From Tolerances § 180.1176...

Residual symptoms and functioning in depression, does the type of residual symptom matter? A post-hoc analysis

Directory of Open Access Journals (Sweden)

Romera Irene

2013-02-01

Full Text Available Abstract Background The degrees to which residual symptoms in major depressive disorder (MDD adversely affect patient functioning is not known. This post-hoc analysis explored the association between different residual symptoms and patient functioning. Methods Patients with MDD who responded (≥50% on the 17-item Hamilton Rating Scale for Depression; HAMD-17 after 3 months of treatment (624/930 were included. Residual core mood-symptoms (HAMD-17 core symptom subscale ≥1, residual insomnia-symptoms (HAMD-17 sleep subscale ≥1, residual anxiety-symptoms (HAMD-17-anxiety subscale ≥1, residual somatic-symptoms (HAMD-17 Item 13 ≥1, pain (Visual Analogue Scale ≥30, and functioning were assessed after 3 months treatment. A stepwise logistic regression model with normal functioning (Social and Occupational Functioning Assessment Scale ≥80 as the dependent variable was used. Results After 3 months, 59.5% of patients (371/624 achieved normal functioning and 66.0% (412/624 were in remission. Residual symptom prevalence was: core mood symptoms 72%; insomnia 63%; anxiety 78%; and somatic symptoms 41%. Pain reported in 18%. Factors associated with normal functioning were absence of core mood symptoms (odds ratio [OR] 8.7; 95% confidence interval [CI], 4.6–16.7, absence of insomnia symptoms (OR 1.8; 95% CI, 1.2–2.7, episode length (4–24 weeks vs. ≥24 weeks [OR 2.0; 95% CI, 1.1–3.6] and better baseline functioning (OR 1.0; 95% CI, 1.0–1.1. A significant interaction between residual anxiety symptoms and pain was found (p = 0.0080. Conclusions Different residual symptoms are associated to different degrees with patient functioning. To achieve normal functioning, specific residual symptoms domains might be targeted for treatment.

Assays of residual antibiotics after treatment of γ-ray and UV irradiation

International Nuclear Information System (INIS)

Shin, Ji Hye; Nam, Ji Hyun; Lee, Dong Hun; Yu, Seung Ho; Lee, Myun Joo

2010-01-01

The pollution of antibiotics is a major cause of spreading antibiotics resistant bacteria in the environment. Applications of ozonation, UV, and γ-ray irradiations have been introduced to remove antibiotics in the effluents from wastewater treatment system. In this study, we compared the chemical (HPLC) and biological (antimicrobial susceptibility test, AMS) assays in measuring of the concentrations of residual antibiotics after γ-ray and UV irradiation. Most samples were degraded by γ-ray irradiation (1 ∼ 2 kGy). However, lincomycin and tetracycline were not degraded by UV irradiation. The concentration of residual antibiotics, that was treated with γ-ray and UV irradiation, measuring by bioassay was similar to HPLC. The concentrations of γ-ray irradiated cephradine measured by AMS test were 2 times higher than of HPLC assay, indicating AMS test is more sensitive than HPLC assay. These results indicate that γ-ray irradiation technique is more useful than UV irradiation, and biological assay is more useful to detect the antibiotics and toxic intermediates in antibiotics degradation

Allergic contact dermatitis from ophthalmic products: can pre-treatment with sodium lauryl sulfate increase patch test sensitivity?

Science.gov (United States)

Corazza, Monica; Virgili, Annarosa

2005-05-01

In patients suspected of allergic contact dermatitis because of topical ophthalmic medicaments, patch tests performed with patients' own products are often negative. The irritant anionic surfactant sodium lauryl sulfate (SLS) may alter the stratum corneum and increase antigen penetration. Pre-treatment of the skin with SLS 0.5% for 24 h was performed in the sites of patch tests with patients' own products in 15 selected patients. In patients previously negative to their own products tested with conventional patch tests, SLS pre-treatment showed 6 new relevant positive reactions and induced a stronger positive reaction in 1 patient. SLS pre-treatment could be proposed as an alternative promising method, which may increase sensitivity of patch tests with patients' own products.

Influence of zeolite treated with sulphuric acid and sodium hydroxide on the coagulation-flocculation process of drainage. Influencia de la zeolita tratada con acido sulfurico y con hidroxido de sodio en el proceso de coagulacion floculacion en aguas superficiales

Energy Technology Data Exchange (ETDEWEB)

Gutierrez Duque, M.; Herrera Vasconcelos, T.; Laria Piedra, N.

1994-01-01

The present paper has had as objective the treatment of natural zeolite from Tasajera with sulfuric acid and sodium hydroxide (residuals acid and basic from the regeneration of cationic and anionic resins of the ''Otto Parallada'' thermoelectric plant) at different times and concentrations, with a further comparison and testing of the effectiveness of the obtained zeolite in respect to the natural one as a coadyuvant of the coagulation-flocculation process in the treatment of superficial water. (Author)

Insights into the mechanisms of mercury sorption onto aluminum based drinking water treatment residuals

Energy Technology Data Exchange (ETDEWEB)

Deliz Quiñones, Katherine, E-mail: Katherine.Deliz@amecfw.com; Hovsepyan, Anna, E-mail: anna_Hovsepyan@urscorp.com; Oppong-Anane, Akua; Bonzongo, Jean-Claude J., E-mail: bonzongo@ufl.edu

2016-04-15

Highlights: • Mercury sorption by Al-WTRs involves electrostatic forces and chemisorption. • Hg forms bonds with oxygen and sulfur atoms of Al-WTR’s organic ligands. • Mercury is incorporated into the residual fraction to form stable complexes. • Mercury binds mainly to SiO{sub x} species in the residual fraction. - Abstract: Several studies have demonstrated the ability of drinking water treatment residuals (WTRs) to efficiently sorb metal cations from aqueous solutions. Reported results have stimulated interest on the potential use of WTRs as sorbent for metal removal from contaminated aqueous effluents as well as in metal immobilization in contaminated soils. However, knowledge on mechanisms of metal sorption by WTRs remains very limited and data on the long-term stability of formed metal–WTR complexes as a function of changing key environmental parameters are lacking. In this study, chemical selective sequential extraction (SSE), scanning electron microscopy combined with X-ray energy dispersive spectrometer (SEM-EDS), and X-ray photoelectron spectroscopy (XPS) were used to gain insight into the different mechanisms of mercury (Hg) binding to aluminum based WTR (Al-WTRs). Results from sorption studies show that a significant portion of Hg becomes incorporated in the operationally defined residual fraction of Al-WTRs, and therefore, not prone to dissolution and mobility. The results of solid phase analyses suggested that Hg immobilization by Al-WTR occurs largely through its binding to oxygen donor atoms of mineral ligands driven by a combination of electrostatic forces and covalent bonding.

Insights into the mechanisms of mercury sorption onto aluminum based drinking water treatment residuals

International Nuclear Information System (INIS)

Deliz Quiñones, Katherine; Hovsepyan, Anna; Oppong-Anane, Akua; Bonzongo, Jean-Claude J.

2016-01-01

Highlights: • Mercury sorption by Al-WTRs involves electrostatic forces and chemisorption. • Hg forms bonds with oxygen and sulfur atoms of Al-WTR’s organic ligands. • Mercury is incorporated into the residual fraction to form stable complexes. • Mercury binds mainly to SiO x species in the residual fraction. - Abstract: Several studies have demonstrated the ability of drinking water treatment residuals (WTRs) to efficiently sorb metal cations from aqueous solutions. Reported results have stimulated interest on the potential use of WTRs as sorbent for metal removal from contaminated aqueous effluents as well as in metal immobilization in contaminated soils. However, knowledge on mechanisms of metal sorption by WTRs remains very limited and data on the long-term stability of formed metal–WTR complexes as a function of changing key environmental parameters are lacking. In this study, chemical selective sequential extraction (SSE), scanning electron microscopy combined with X-ray energy dispersive spectrometer (SEM-EDS), and X-ray photoelectron spectroscopy (XPS) were used to gain insight into the different mechanisms of mercury (Hg) binding to aluminum based WTR (Al-WTRs). Results from sorption studies show that a significant portion of Hg becomes incorporated in the operationally defined residual fraction of Al-WTRs, and therefore, not prone to dissolution and mobility. The results of solid phase analyses suggested that Hg immobilization by Al-WTR occurs largely through its binding to oxygen donor atoms of mineral ligands driven by a combination of electrostatic forces and covalent bonding.

Restaurant menu labelling: Is it worth adding sodium to the label?

Science.gov (United States)

Scourboutakos, Mary J; Corey, Paul N; Mendoza, Julio; Henson, Spencer J; L'Abbe, Mary R

2014-07-31

Several provincial and federal bills have recommended various forms of menu labelling that would require information beyond just calories; however, the additional benefit of including sodium information is unknown. The objective of this study was to determine whether sodium information on menus helps consumers make lower-sodium choices and to understand what other factors influence the effect of menu labelling on consumers' meal choices. A total of 3,080 Canadian consumers completed an online survey that included a repeated measures experiment in which consumers were asked to select what they would typically order from four mock-restaurant menus. Subsequently, consumers were randomly allocated to see one of three menu-labelling treatments (calories; calories and sodium; or calories, sodium and serving size) and were given the option to change their order. There was a significant difference in the proportion of consumers who changed their order, varying from 17% to 30%, depending on the restaurant type. After participants had seen menu labelling, sodium levels decreased in all treatments (p<0.0001). However, in three of the four restaurant types, consumers who saw calorie and sodium information ordered meals with significantly less sodium than consumers who saw only calorie information (p<0.01). Consumers who saw sodium labelling decreased the sodium level of their meal by an average of 171-384 mg, depending on the restaurant. In the subset of consumers who saw sodium information and chose to change their order, sodium levels decreased by an average of 681-1,360 mg, depending on the restaurant. Sex, intent to lose weight and the amount of calories ordered at baseline were the most important predictors of who used menu labelling. Eighty percent of survey panelists wanted to see nutrition information when dining out. Including sodium information alongside calorie information may result in a larger decrease in the amount of sodium ordered by restaurant-goers.

Sodium

Science.gov (United States)

Table salt is a combination of two minerals - sodium and chloride Your body needs some sodium to work properly. It helps with the function ... in your body. Your kidneys control how much sodium is in your body. If you have too ...

Omics approaches on fresh-cut lettuce reveal global molecular responses to sodium hypochlorite and peracetic acid treatment.

Science.gov (United States)

Daddiego, Loretta; Bianco, Linda; Capodicasa, Cristina; Carbone, Fabrizio; Dalmastri, Claudia; Daroda, Lorenza; Del Fiore, Antonella; De Rossi, Patrizia; Di Carli, Mariasole; Donini, Marcello; Lopez, Loredana; Mengoni, Alessio; Paganin, Patrizia; Perrotta, Gaetano; Bevivino, Annamaria

2018-01-01

Lettuce is a leafy vegetable that is extensively commercialized as a ready-to-eat product because of its widespread use in human nutrition as salad. It is well known that washing treatments can severely affect the quality and shelf-life of ready-to-eat vegetables. The study presented here evaluated the effect of two washing procedures on fresh-cut lettuce during storage. An omics approach was applied to reveal global changes at molecular level induced by peracetic acid washing in comparison with sodium hypochlorite treatment. Microbiological analyses were also performed to quantify total bacterial abundance and composition. The study revealed wide metabolic alterations induced by the two sanitizers. In particular, transcriptomic and proteomic analyses pointed out a number of transcripts and proteins differentially accumulated in response to peracetic acid washing, mainly occurring on the first day of storage. In parallel, different microbiota composition and significant reduction in total bacterial load following washing were also observed. The results provide useful information for the fresh-cut industry to select an appropriate washing procedure preserving fresh-like attributes as much as possible during storage of the end product. Molecular evidence indicated peracetic acid to be a valid alternative to sodium hypochlorite as sanitizer solution. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Neurodevelopmental Outcome and Treatment Efficacy of Benzoate and Dextromethorphan in Siblings with Attenuated Nonketotic Hyperglycinemia.

Science.gov (United States)

Bjoraker, Kendra J; Swanson, Michael A; Coughlin, Curtis R; Christodoulou, John; Tan, Ee S; Fergeson, Mark; Dyack, Sarah; Ahmad, Ayesha; Friederich, Marisa W; Spector, Elaine B; Creadon-Swindell, Geralyn; Hodge, M Antoinette; Gaughan, Sommer; Burns, Casey; Van Hove, Johan L K

2016-03-01

To evaluate the impact of sodium benzoate and dextromethorphan treatment on patients with the attenuated form of nonketotic hyperglycinemia. Families were recruited with 2 siblings both affected with attenuated nonketotic hyperglycinemia. Genetic mutations were expressed to identify residual activity. The outcome on developmental progress and seizures was compared between the first child diagnosed and treated late with the second child diagnosed at birth and treated aggressively from the newborn period using dextromethorphan and benzoate at dosing sufficient to normalize plasma glycine levels. Both siblings were evaluated with similar standardized neurodevelopmental measures. In each sibling set, the second sibling treated from the neonatal period achieved earlier and more developmental milestones, and had a higher developmental quotient. In 3 of the 4 sibling pairs, the younger sibling had no seizures whereas the first child had a seizure disorder. The adaptive behavior subdomains of socialization and daily living skills improved more than motor skills and communication. Early treatment with dextromethorphan and sodium benzoate sufficient to normalize plasma glycine levels is effective at improving outcome if used in children with attenuated disease with mutations providing residual activity and when started from the neonatal period. Copyright © 2016 The Authors. Published by Elsevier Inc. All rights reserved.

Investigation on reusing water treatment residuals to remedy soil contaminated with multiple metals in Baiyin, China

Energy Technology Data Exchange (ETDEWEB)

Wang, Changhui; Zhao, Yuanyuan [The Key Laboratory of Water and Sediment Sciences, Ministry of Education, School of Environment, Beijing Normal University, Beijing 100875 (China); Pei, Yuansheng, E-mail: yspei@bnu.edu.cn [The Key Laboratory of Water and Sediment Sciences, Ministry of Education, School of Environment, Beijing Normal University, Beijing 100875 (China)

2012-10-30

Highlights: Black-Right-Pointing-Pointer Fe/Al water treatment residuals (FARs) can stabilize As, Pb, Ni, Zn, Cr and Cu. Black-Right-Pointing-Pointer FARs cannot stabilize Ba and Cd. Black-Right-Pointing-Pointer The properties of FARs and soil affect the FARs' ability of stabilizing metals. - Abstract: In this work, the remediation of soils contaminated with multiple metals using ferric and alum water treatment residuals (FARs) in Baiyin, China, was investigated. The results of metals fractionation indicated that after the soil was treated with FARs, arsenic (As), lead (Pb), nickel (Ni), zinc (Zn) and copper (Cu) could be transformed into more stable forms, i.e., As bound in crystalline Fe/Al oxides and other metals in the oxidable and residual forms. However, the forms of chromium (Cr) and cadmium (Cd) were unaffected. Interestingly, due to the effect of FARs, barium (Ba) was predominantly transformed into more mobile forms. The bioaccessibility extraction test demonstrated that the FARs reduced the bioaccessibility of As by 25%, followed by Cu, Cr, Zn, Ni and Pb. The bioaccessibility of Cd and Ba were increased; in particular, there was an increase of 41% for Ba at the end of the test. In conclusion, the FARs can be used to remedy soil contaminated with multiple metals, but comprehensive studies are needed before practical applications of this work.

Integrating biological treatment of crop residue into a hydroponic sweetpotato culture

Science.gov (United States)

Trotman, A. A.; David, P. P.; Bonsi, C. K.; Hill, W. A.; Mortley, D. G.; Loretan, P. A.

1997-01-01

Residual biomass from hydroponic culture of sweetpotato [Ipomoea batatas (L.) Lam.] was degraded using natural bacterial soil isolates. Sweetpotato was grown for 120 days in hydroponic culture with a nutrient solution comprised of a ratio of 80% modified half Hoagland solution to 20% filtered effluent from an aerobic starch hydrolysis bioreactor. The phytotoxicity of the effluent was assayed with `Waldmann's Green' lettuce (Lactuca sativa L.) and the ratio selected after a 60-day bioassay using sweetpotato plants propagated vegetatively from cuttings. Controlled environment chamber experiments were conducted to investigate the impact of filtrate from biological treatment of crop residue on growth and storage root production with plants grown in a modified half Hoagland solution. Incorporation of bioreactor effluent, reduced storage root yield of `Georgia Jet' sweetpotato but the decrease was not statistically significant when compared with yield for plants cultured in a modified half Hoagland solution without filtrate. However, yield of `TU-82-155' sweetpotato was significantly reduced when grown in a modified half Hoagland solution into which filtered effluent had been incorporated. Total biomass was significantly reduced for both sweetpotato cultivars when grown in bioreactor effluent. The leaf area and dry matter accumulation were significantly (P < 0.05) reduced for both cultivars when grown in solution culture containing 20% filtered effluent.

Assessment of residual life of fast breeder test reactor

International Nuclear Information System (INIS)

Srinivasan, G.

2016-01-01

The Fast Breeder Test Reactor (FBTR) is a loop type sodium cooled fast reactor and has been in operation since 1985. As a part of regulatory requirement for relicensing, residual life assessment had to be carried out. The systems are made of SS 316, and designed for creep and fatigue. The design life for creep is 100,000 h at 550°C. The design fatigue cycle for operation from shutdown to full power varies from component to component. In general, most of the components are designed for 2000 cycles. The reactor has operated mostly below the design temperatures. It is seen that enough creep-fatigue life is available for the non-replaceable, permanent components. The residual life was found to be governed by the residual ductility of the Grid Plate supporting the core after neutron irradiation. Fast flux measurements were carried out at the grid plate location. Samples were irradiated and tensile tested. Results indicate the allowable dpa for a 10% residual ductility criterion as 4.37. This gave a residual life of ~ 6 Effective Full Power Years for the reactor as of Feb 2012. Measures to reduce the neutron dose on the grid plate are being taken. (author)

Glycerin Borax Treatment of Exfoliative Cheilitis Induced by Sodium Lauryl Sulfate: a Case Report.

Science.gov (United States)

Thongprasom, Kobkan

2016-06-01

This paper reports on the results of a case study of a 19-year-old female who presented to the Oral Medicine clinic with a chief complaint of scaly and peeling lips. The lesions had persisted on her lips for more than 7 years and were refractory to previous treatment. Her physician's diagnosis was contact dermatitis. We diagnosed this patient as having exfoliative cheilitis (EC). A patch test using the toothpaste containing sodium lauryl sulfate (SLS) was positive and the patient discontinued using it. Instead, she started using a toothpaste not containing SLS. One year after treating her lesions with hydrogen peroxide mouthwash 1% and glycerin borax, a gradual improvement was observed until returning to normal. Glycerin borax was safe, low cost and simple to use in treatment of refractory exfoliative cheilitis. SLS may have been a precipitating factor in EC in this case.

Glycerin Borax Treatment of Exfoliative Cheilitis Induced by Sodium Lauryl Sulfate: a Case Report

Directory of Open Access Journals (Sweden)

Kobkan Thongprasom

2016-01-01

Full Text Available This paper reports on the results of a case study of a 19-year-old female who presented to the Oral Medicine clinic with a chief complaint of scaly and peeling lips. The lesions had persisted on her lips for more than 7 years and were refractory to previous treatment. Her physician’s diagnosis was contact dermatitis. We diagnosed this patient as having exfoliative cheilitis (EC. A patch test using the toothpaste containing sodium lauryl sulfate (SLS was positive and the patient discontinued using it. Instead, she started using a toothpaste not containing SLS. One year after treating her lesions with hydrogen peroxide mouthwash 1% and glycerin borax, a gradual improvement was observed until returning to normal. Glycerin borax was safe, low cost and simple to use in treatment of refractory exfoliative cheilitis. SLS may have been a precipitating factor in EC in this case.

Thermal treatment system of hazardous residuals in three heating zones based on a microprocessor

International Nuclear Information System (INIS)

Luna H, C.L.

1997-01-01

Thermal treatment system consists of a high power electric oven of three heating zones where each zone works up to 1200 Centigrades; it has the capacity of rising the central zone temperature up to 1000 Centigrades in 58 minutes approximately. This configuration of three zones could be programmed to different temperatures and they will be digitally controlled by a control microprocessor, which has been controlled by its own assembler language, in function of the PID control. There are also other important controls based on this microprocessor, as a signal amplification, starting and shutdown of high power step relays, activation and deactivation of both analogic/digital and digital/analogic convertors, port activation and basic data storage of the system. Two main characteristics were looked for this oven design; the first was the possibility of controlling the three zone temperature and the second was to reduce the rising and stabilization operation time and its digitized control. The principal function of the three zone oven is to accelerate the degradation of hazardous residuals by an oxidation instead combustion, through relatively high temperatures (minimum 800 Centigrades and maximum 1200 Centigrades); this process reduces the ash and volatile particulate production. The hazardous residuals will be pumped into the degradation system and after atomized through a packaged column; this step will avoid the direct contact of the residuals with the oven cores. These features make this system as closed process, which means that the residuals can not leak to the working area, reducing the exposure risk to the personnel. This three step oven system is the first stage of the complete hazardous residuals degradation system; after this, the flow will go into a cold plasma region where the process is completed, making a closed system. (Author)

Proteomic Investigation of Protein Profile Changes and Amino Acid Residue Level Modification in Cooked Lamb Meat: The Effect of Boiling.

Science.gov (United States)

Yu, Tzer-Yang; Morton, James D; Clerens, Stefan; Dyer, Jolon M

2015-10-21

Hydrothermal treatment (heating in water) is a common method of general food processing and preparation. For red-meat-based foods, boiling is common; however, how the molecular level effects of this treatment correlate to the overall food properties is not yet well-understood. The effects of differing boiling times on lamb meat and the resultant cooking water were here examined through proteomic evaluation. The longer boiling time was found to result in increased protein aggregation involving particularly proteins such as glyceraldehyde-3-phosphate dehydrogenase, as well as truncation in proteins such as in α-actinin-2. Heat-induced protein backbone cleavage was observed adjacent to aspartic acid and asparagine residues. Side-chain modifications of amino acid residues resulting from the heating, including oxidation of phenylalanine and formation of carboxyethyllysine, were characterized in the cooked samples. Actin and myoglobin bands from the cooked meat per se remained visible on sodium dodecyl sulfate-polyacrylamide gel electrophoresis, even after significant cooking time. These proteins were also found to be the major source of observed heat-induced modifications. This study provides new insights into molecular-level modifications occurring in lamb meat proteins during boiling and a protein chemistry basis for better understanding the effect of this common treatment on the nutritional and functional properties of red-meat-based foods.

Design and test of a vacuum distillation method for determining carbon in sodium

International Nuclear Information System (INIS)

Irmisch, R.; Rettig, D.; Woelke, K.

1976-08-01

A method is described for determining total and carbonate carbon in sodium samples until 10 g. Sodium is removed by vacuum distillation at 300 0 C and the carbon in the residue is converted to carbon dioxide by combustion in a stream of air or thermic splitting in a stream of cover gas at 1000 0 C. The carbon dioxide is measured manometrically. It is therefore not necessary to carry out calibration. Distillation and combustion rig are combined with inertgas filled transfer box. Therefore the sodium sample does not get into touch with air. Test of this method was carried out with Na 2 CO 3 and WC. Carbon recoveries were for Na 2 CO 3 between 103 and 107% and for WC between 92 and 96%. The blank value found being 9 μg C and sensitivity 3 μg C. (author)

Reduced-Sodium Lunches Are Well-Accepted by Uninformed Consumers Over a 3-Week Period and Result in Decreased Daily Dietary Sodium Intakes: A Randomized Controlled Trial.

Science.gov (United States)

Janssen, Anke M; Kremer, Stefanie; van Stipriaan, Willeke L; Noort, Martijn W J; de Vries, Jeanne H M; Temme, Elisabeth H M

2015-10-01

Processed foods are major contributors to excessive sodium intake in Western populations. We investigated the effect of food reformulation on daily dietary sodium intake. To determine whether uninformed consumers accept reduced-sodium lunches and to determine the effect of consuming reduced-sodium lunches on 24-hour urinary sodium excretion. A single-blind randomized controlled pretest-posttest design with two parallel treatment groups was used. Participants chose foods in an experimental real-life canteen setting at the Restaurant of the Future in Wageningen, the Netherlands, from May 16 until July 1, 2011. After a run-in period with regular foods for both groups, the intervention group (n=36) consumed foods with 29% to 61% sodium reduction (some were partially flavor compensated). The control group (n=38) continued consuming regular foods. Outcomes for assessment of acceptance were the amount of foods consumed, energy and sodium intake, remembered food liking, and intensity of sensory aspects. Influence on daily dietary sodium intake was assessed by 24-hour urinary sodium excretion. Between and within-subject comparisons were assessed by analysis of covariance. Energy intake and amount consumed of each food category per lunch remained similar for both groups. Compared with the control group, the intervention group's sodium intake per lunch was significantly reduced by -1,093 mg (adjusted difference) (95% CI -1,285 to -901), equivalent to 43 mmol sodium. Remembered food liking, taste intensity, and saltiness were scored similarly for almost all of the reduced-sodium foods compared with the regular foods. After consuming reduced-sodium lunches, compared with the control group, intervention participants' 24-hour urinary sodium excretion was significantly lower by -40 mEq (adjusted difference) (95% CI -63 to -16) than after consuming regular lunches, and this reflects a decreased daily sodium intake of 1 g. Comparing the two treatment groups, consumption of reduced-sodium

DESIGN AND DEVELOPMENT OF MUCOADHESIVE DRUG DELIVERY SYSTEM OF MONTELUKAST SODIUM

OpenAIRE

N. G. Raghavendra Rao; V. B. Suryakar

2011-01-01

The Montelukast sodium is a leukotrine receptor antagonist used for the maintenance treatment of asthma, chronic asthma attacks and to relieve symptoms of seasonal allergies. The biological half life of montelukast sodium is 2.5 to 5.5 hrs and poor bioavailability upto 64%. Because of poor bioavailability of montelukast sodium by oral route, there is a need to increase its bioavailability by formulating it into buccal dosage forms. Hence, montelukast sodium is a suitable drug for buccal dosa...

Noninvasive treatment choice for an aged down syndrome patient presenting a residual periapical cyst.

Science.gov (United States)

Sperandio, Felipe Fornias; Carli, Marina Lara de; Guimaräes, Eduardo Pereira; Pereira, Alessandro Antônio Costa; Hanemann, Joäo Adolfo Costa

2014-03-01

This is the first report to illustrate the marsupialization as an effective treatment for a Down Syndrome (DS) patient presenting a residual periapical cyst. These cysts occur within the alveolar ridge, usually at the local site of a previously extracted tooth that did not received proper curettage; usually the surgical excision of a cyst and also the vigorous curettage of a socket is very simple, if not for the fact that mentally disabled patients require rapid and non-stressful procedures. The 54-year-old DS patient represented herein received a minimally invasive marsupialization under local anesthesia. Due to the large extent of the lesion, the acrylic resin drain was maintained for 30 days. Through the following period, a daily irrigation of the cystic cavity with saline solution was carried out to prevent a secondary infection within the cystic cavity. A follow-up of 16 months showed no signs of recurrence. Marsupialization of residual periapical cyst is completely effective and safe, even for a DS patient that is considered to be at an advanced age. Marsupialization poses as a minimally invasive choice for mentally disabled patients, even when presenting advanced ages; treatment success was stated by the easy clinical conduct, uneventful postoperative situation and the lack of recurrence along 16 months of follow-up.

The role of disease-linked residue glutamine-913 in support of the structure and function of the human electrogenic sodium/bicarbonate cotransporter NBCe1-A.

Science.gov (United States)

Myers, Evan J; Marshall, Aniko; Parker, Mark D

2018-02-15

Mutations in the sodium bicarbonate cotransporter NBCe1 (SLC4A4) cause proximal renal tubular acidosis (pRTA). We recently described a novel pRTA mutation p.Gln913Arg (Q913R), inherited in compound heterozygous form with p.Arg510His (R510H). Q913R causes intracellular retention of NBCe1 and a 'gain of function' Cl - leak. To learn more about the importance of glutamine at position 913, we substituted a variety of alternative amino-acid residues (Cys, Glu, Lys, Leu, Ser) at position 913. Studying cRNA-injected Xenopus oocytes by voltage clamp, we find that most de novo mutants exhibit close-to-normal NBCe1 activity; only Q913K expresses a Cl - leak. Studying transiently-transfected, polarised kidney cells by fluorescence microscopy we find that most de novo mutants (except Q913E) are intracellularly retained. A 3D homology model predicts that Gln913 is located in the gating domain of NBCe1 and neighbours the 3D space occupied by another pRTA-associated residue (Arg881), highlighting an important and conformationally-sensitive region of NBCe1. We conclude that the intracellular retention of Q913R is caused by the loss of Gln at position 913, but that the manifestation of the Cl - leak is related to the introduction of Arg at position 913. Our findings will inform future studies to elucidate the nature and the consequences of the leak.

Neutron diffraction measurements for the determination of heat treatment effectiveness in generating compressive residual stress in an automotive crown gear

International Nuclear Information System (INIS)

Albertini, G.; Fiori, F.; Girardin, E.; Giuliani, A.; Pyzalla, A.; Quadrini, E.

1999-01-01

Complete text of publication follows. Thermal austenitizing and tempering treatments are being developed in automotive industry to prevent crack initiation and avoid crack propagation, especially in components where stress intensity factors influence the stress field and then the fatigue life of the component itself. This is the case of crown gears, where the teeth root undergoes frequently to cracking when tensile residual stresses are present at the surface, as typical loads are impulsive and very high. The sign reversal of these stresses is the aim of austenitizing and tempering treatments. In this work residual stress measurements carried out at HMI-BENSC are presented, in a UNI55Cr3 steel crown gear submitted to such kind of treatments, performed with a new multi-frequency induction technique whose effectiveness is checked. (author)

Management of industrial solid residues; Gerenciamento de residuos solidos industriais

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-07-01

This chapter gives an overview on the management of industrial solid wastes, approaching the following subjects: classification of industrial solid residues; directives and methodologies for the management of industrial solid residues; instruments for the management of industrial solid residues; handling, packing, storage and transportation; treatment of industrial solid residues; final disposal - landfill for industrial residues; the problem of treatment and final disposer of domestic garbage in Brazil; recycling of the lubricant oils used in brazil; legislation.

Sodium fire tests for investigating the sodium leak in Monju

International Nuclear Information System (INIS)

Seino, Hiroshi; Miyahara, Shinya; Miyake, Osamu; Tanabe, Hiromi

1996-01-01

As a part of the work for investigating the sodium leak accident which occurred in Monju on December 8, 1995, three tests, (1) sodium leak test, (2) sodium fire test-I, and (3) sodium fire test-II, were carried out at OEC/PNC. Main objectives of these tests are to confirm leak and burning behavior of sodium from the damaged thermometer, and effects of the sodium fire on integrity of the surrounding structure, etc. The main conclusions obtained from the tests are shown as below. 1) Average sodium leak rate obtained from the sodium leak test was about 50 g/sec. This was equivalent to the value estimated from level change in the sodium overflow tank in the Monju accident. 2) Observation from video cameras in the sodium fire tests revealed that in early stages of sodium leak, sodium dropped down out of the flexible tube of thermometer in drips. This dripping and burning were expanded in range as sodium splashed on the duct. 3) Though, in the sodium fire test-I, there was a decrease of about 1 mm at a thickness of the burning pan in the vicinity in just under in the leak point, there were completely no crack and failure. In the meantime, in the sodium fire test-II the six open holes were found in the floor liner. By this liner failure, the reaction between sodium and concrete might take place. At present, while the detailed evaluation on the sodium fire test-II has been mainly carried out, the investigation for clarifying the cause of the liner failure has been also carried out. (author)

Mycophenolate sodium for the treatment of chronic non-infectious uveitis of childhood.

Science.gov (United States)

Doycheva, Deshka; Zierhut, Manfred; Blumenstock, Gunnar; Sobolewska, Bianka; Voykov, Bogomil; Hohmann, Johanna; Spitzer, Martin S; Deuter, Christoph

2016-08-01

To assess the efficacy and tolerability of mycophenolate sodium (MPS) in the therapy of children with chronic non-infectious uveitis. Retrospective analysis of 23 children with chronic uveitis, treated with MPS, with a follow-up of at least 6 months. The main outcome measures were time to uveitis reactivation and corticosteroid-sparing effect under MPS treatment. The secondary outcome measures were best-corrected visual acuity (BCVA) and treatment-related side effects. From 23 patients included in the study, 2 patients had anterior uveitis, 19 had intermediate uveitis and 2 had panuveitis. The probability of reactivation-free survival after MPS initiation was estimated as 65% at both 1 and 2 years. The probability of discontinuing systemic corticosteroids after 1 year of treatment was 39% and after 2 years 51%. The probability to taper corticosteroids to a daily dosage of ≤0.1 mg/kg after 1 and 2 years was 62% and 85%, respectively. BCVA improved or remained stable in 96% of eyes after 1 year of therapy. Treatment-related side effects were found in nine children (rate: 0.17/patient-year). No therapy discontinuation because of side effects was needed. Our data suggest that MPS is useful and well tolerated in children with chronic uveitis. MPS seems to be an effective drug for the treatment of chronic non-infectious uveitis of childhood and may be preferred as a first-line steroid-sparing agent in this form of uveitis. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

Treatment and Recycling of the Process Water in Iron Ore Flotation of Yuanjiacun Iron Mine

Directory of Open Access Journals (Sweden)

Wen-li Jiang

2017-01-01

Full Text Available Coagulating sedimentation and oxidation treatment of process water in iron ore flotation of Yuanjiacun iron mine had been studied. The process water of this mine carried residual polyacrylamide (PAM, poly(diallyldimethylammonium chloride (PDADMAC, and Ca2+ from the flotation and caused decrease of the iron flotation recovery or grade of the concentrate. The studies on high-intensity magnetic separation (HIMS tailings for coagulating sedimentation showed that the settling performance of coagulant (named CYH was better than that of PDADMAC. The analyses of FTIR spectra and zeta potential demonstrated that CYH is adsorbed mainly through electrostatic attraction onto HIMS tailings. Sodium hypochlorite was adopted to oxidize the residual organics in tailings wastewater. When sodium hypochlorite is at the dosage of 1.0 g/L, reaction temperature is of 20°C, and reaction time is of 30 minutes, the removal rates of PAM, COD, and Ca2+ were 90.48%, 83.97%, and 85.00%, respectively. Bench-scale flotation studies on the treated tailings wastewater indicated that the iron recovery and grade of concentrate were close to those of freshwater.

The Increased Content of Micronutrients in Celery, Carrot, Parsnip and Parsley Plants after Treatment with Sodium Naphthenate

Directory of Open Access Journals (Sweden)

Grbović Ljubica

2016-08-01

Full Text Available Young plants of celery, parsley, parsnip and carrot, grown in nutrient solution, were treated with sodium naphthenate (10−7 mol dm−3, applying foliar and root treatments. Both treatments affected the root content of all investigated elements present in the nutrient solution, but in a different way, depending on the plant species. An average change (increase/decrease in the contents of investigated essential elements was about 35%. Our experiments with naphthenate showed that this treatment may enhance the efficiency of essential elements uptake and increase its content in plants without changing concentration of these elements in the nutrient solution. Especially interesting results were obtained in the case of carrot, as increased contents were observed in the elements that are usually deficient in nutrition (Fe, Zn, Mn, whereas the other remained unchanged.

Efficiency and effectiveness of gamma rays and sodium azide in Sesbania cannabina Poir

International Nuclear Information System (INIS)

Kumar, G.; Srivastava, N.

2013-01-01

Mutagenic effectiveness and efficiency is an important factor for the selection of a mutagen for a mutation breeding program. Mutagenic effectiveness is a measure of the frequency of mutations induced by a unit mutagen dose, while mutagenic efficiency is a measure of the proportion of mutations in relation to undesirable changes such as lethality, sterility, meiotic aberrations etc. The present study envisages the mutagenic effectiveness and efficiency of individual and combined treatments of chemical and physical mutagens i.e. sodium azide (individual), gamma rays (individual) and sodium azide + gamma ray (combined). For the individual treatment of sodium azide, the seeds of the Sesbania cannabina variety ND-1 were treated with 0.5% solution of sodium azide (SA) for four different time durations, i.e. 3, 5, 7, and 9 h, and for the individual treatment of gamma rays, dry and healthy seeds were treated with 20, 40, 60, and 80 Kr doses of gamma rays. For the combined treatment, the seeds were exposed to four different doses of gamma rays (20, 40, 60, and 80 Kr) and after irradiation seeds were treated with 0.5% solution of sodium azide for 3 h. After treatment, seeds subjected to individual and combined treatment were sown in randomized block design to raise the M 1 generation and a study was conducted on germination percentage, survival percentage, pollen fertility percentage, and chromosomal aberrations at different doses of the individual and combined treatments. (author)

Sodium technology handbook

International Nuclear Information System (INIS)

2005-09-01

This document was published as a textbook for the education and training of personnel working for operations and maintenances of sodium facilities including FBR plants and those engaged in R and D activities related to sodium technology. This handbook covers the following technical areas. Properties of sodium. Compatibilities of sodium with materials. Thermalhydraulics and structural integrity. Sodium systems and components. Sodium instrumentations. Sodium handling technology. Sodium related accident evaluation and countermeasures for FBRs. Operation, maintenance and repair technology of sodium facilities. Safety measures related to sodium. Laws, regulations and internal rules related to sodium. The plannings and discussions of the handbook were made in the Sodium Technology Education Committee organized in O-arai Engineering Center consisting of the representatives of the related departments including Tsuruga headquarters. Experts in various departments participated in writing individual technical subjects. (author)

Effect of pre-treatments on methane production potential of energy crops and crop residues

Energy Technology Data Exchange (ETDEWEB)

Lehtomaki, A.; Ronkainen; Rintala, J.A. [Jyvaskla Univ. (Finland). Dept. of Biological and Environmental Sciences; Viinikainen, T.A. [Jyvaskla Univ. (Finland). Dept. of Chemistry

2004-07-01

Energy crops, that is, crops grown specifically for energy purposes are an alternative to food production in areas with sufficient agricultural land. Crop residues are also a potential source of energy. The anaerobic digestion of solid materials is limited by hydrolysis of complex polymeric substances such as lignocellulose. The methane producing potential of ligno cellulosic material is to pretreat the substrate in order to break up the polymer chains to more easily accessible soluble compounds. In this study, three different substrates were used: sugar beet tops, grass hay, and straw of oats. Biological pretreatments were the following: enzyme treatment, composting, white-rot fungi treatment. Also, pretreatment in water was tried. Chemical pretreatments included peracetic acid treatment, and treatment with two different alkalis. Alkaline pretreatments of hay and sugar beet tops have the potential to improve the methane yield. For instance, the yield of grass hay was increased 15 per cent by one particular alkaline treatment. Straw did not respond to any of the treatments tried. 18 refs., 1 tab., 2 figs.

Increased renal sodium absorption by inhibition of prostaglandin synthesis during fasting in healthy man. A possible role of the epithelial sodium channels

Directory of Open Access Journals (Sweden)

Graffe Carolina C

2010-10-01

Full Text Available Abstract Background Treatment with prostaglandin inhibitors can reduce renal function and impair renal water and sodium excretion. We tested the hypotheses that a reduction in prostaglandin synthesis by ibuprofen treatment during fasting decreased renal water and sodium excretion by increased absorption of water and sodium via the aquaporin2 water channels and the epithelial sodium channels. Methods The effect of ibuprofen, 600 mg thrice daily, was measured during fasting in a randomized, placebo-controlled, double-blinded crossover study of 17 healthy humans. The subjects received a standardized diet on day 1, fasted at day 2, and received an IV infusion of 3% NaCl on day 3. The effect variables were urinary excretions of aquaporin2 (u-AQP2, the beta-fraction of the epithelial sodium channel (u-ENaCbeta, cyclic-AMP (u-cAMP, prostaglandin E2 (u-PGE2. Free water clearance (CH2O, fractional excretion of sodium (FENa, and plasma concentrations of vasopressin, angiotensin II, aldosterone, atrial-, and brain natriuretic peptide. Results Ibuprofen decreased u-AQP2, u-PGE2, and FENa at all parts of the study. During the same time, ibuprofen significantly increased u-ENaCbeta. Ibuprofen did not change the response in p-AVP, u-c-AMP, urinary output, and free water clearance during any of these periods. Atrial-and brain natriuretic peptide were higher. Conclusion During inhibition of prostaglandin synthesis, urinary sodium excretion decreased in parallel with an increase in sodium absorption and increase in u-ENaCbeta. U-AQP2 decreased indicating that water transport via AQP2 fell. The vasopressin-c-AMP-axis did not mediate this effect, but it may be a consequence of the changes in the natriuretic peptide system and/or the angiotensin-aldosterone system Trial Registration Clinical Trials Identifier: NCT00281762

Photocatalytic degradation of rhodamine B, paracetamol and diclofenac sodium by supported titania-based catalysts from petrochemical residue: effect of doping with magnesium.

Science.gov (United States)

da Silva, William Leonardo; Lansarin, Marla Azário; Dos Santos, João Henrique Z; Silveira, Fernando

2016-11-01

Three different lots of a residual Ziegler-Natta catalyst slurry (bearing Ti and Mg) obtained from an industrial petrochemical plant were employed as sources for the photocatalyst supported on silica. The effect of additional magnesium (1.0-25.0 wt% Mg/SiO 2 ) on the photocatalytic properties of the doped materials was investigated. Doping the titania-based photocatalyst with Mg results in a shift in the absorption threshold toward the visible spectrum. The optical band gap energy of the bare supported photocatalyst was in the range of 2.5 eV and shifted to 1.72 eV after 25 wt% Mg doping. The systems were evaluated for the photodegradation of one dye (rhodamine B (RhB)) and two drugs (paracetamol and diclofenac sodium) either under ultraviolet (UV) (365 nm - UVA) or visible radiation, separately. Among the evaluated systems, doping with 25 wt% Mg afforded the highest degradation values for the target molecules under UV and visible radiation (i.e. 87%, 60% and 55% of the RhB, paracetamol and diclofenac under UV, respectively, and 82%, 48.3% and 48% under visible irradiation, respectively).

Ion Recognition Approach to Volume Reduction of Alkaline Tank Waste by Separation and Recycle of Sodium Hydroxide and Sodium Nitrate

International Nuclear Information System (INIS)

Moyer, Bruce A.; Marchand, Alan P.; Bonnesen, Peter V.; Bryan, Jeffrey C.; Haverlock, Tamara J.

2004-01-01

This research was intended to provide the scientific foundation upon which the feasibility of liquid-liquid extraction chemistry for bulk reduction of the volume of high-activity tank waste can be evaluated. Primary focus has been on sodium hydroxide separation, with potential Hanford application. Value in sodium hydroxide separation can potentially be found in alternative flowsheets for treatment and disposal of low-activity salt waste. Additional value can be expected in recycle of sodium hydroxide for use in waste retrieval and sludge washing, whereupon additions of fresh sodium hydroxide to the waste can be avoided. Potential savings are large both because of the huge cost of vitrification of the low-activity waste stream and because volume reduction of high-activity wastes could obviate construction of costly new tanks. Toward these ends, the conceptual development begun in the original proposal was extended with the formulation of eight fundamental approaches that could be undertaken for extraction of sodium hydroxide

Layered double hydroxide using hydrothermal treatment: morphology evolution, intercalation and release kinetics of diclofenac sodium

Science.gov (United States)

Joy, Mathew; Iyengar, Srividhya J.; Chakraborty, Jui; Ghosh, Swapankumar

2017-12-01

The present work demonstrates the possibilities of hydrothermal transformation of Zn-Al layered double hydroxide (LDH) nanostructure by varying the synthetic conditions. The manipulation in washing step before hydrothermal treatment allows control over crystal morphologies, size and stability of their aqueous solutions. We examined the crystal growth process in the presence and the absence of extra ions during hydrothermal treatment and its dependence on the drug (diclofenac sodium (Dic-Na)) loading and release processes. Hexagonal plate-like crystals show sustained release with ˜90% of the drug from the matrix in a week, suggesting the applicability of LDH nanohybrids in sustained drug delivery systems. The fits to the release kinetics data indicated the drug release as a diffusion-controlled release process. LDH with rod-like morphology shows excellent colloidal stability in aqueous suspension, as studied by photon correlation spectroscopy.

Layered double hydroxide using hydrothermal treatment: morphology evolution, intercalation and release kinetics of diclofenac sodium

Institute of Scientific and Technical Information of China (English)

Mathew JOY; Srividhya J.IYENGAR; Jui CHAKRABORTY; Swapankumar GHOSH

2017-01-01

The present work demonstrates the possibilities of hydrothermal transformation of Zn-AI layered double hydroxide (LDH) nanostructure by varying the synthetic conditions.The manipulation in washing step before hydrothermal treatment allows control over crystal morphologies,size and stability of their aqueous solutions.We examined the crystal growth process in the presence and the absence of extra ions during hydrothermal treatment and its dependence on the drug (diclofenac sodium (DicNa)) loading and release processes.Hexagonal plate-like crystals show sustained release with ～90％ of the drug from the matrix in a week,suggesting the applicability of LDH nanohybrids in sustained drug delivery systems.The fits to the release kinetics data indicated the drug release as a diffusion-controlled release process.LDH with rod-like morphology shows excellent colloidal stability in aqueous suspension,as studied by photon correlation spectroscopy.

Quality of diets with fluidized bed combustion residue treatment: I. Rat trials

Energy Technology Data Exchange (ETDEWEB)

Cahill, N.J.; Reid, R.L.; Head, M.K.; Hern, J.L.; Bennett, O.L.

Feeding trials were conducted with rats (Rattus rattus) to examine effects of soil application, or dietary inclusion, of fluidized bed combustion residue (FBCR) on the composition and quality of foods. Four diets (vegetable protein, egg protein, chicken, chicken + dietary FBCR) prepared with either FBCR or lime (control) treatments, were fed to weanling, female rats in three growth and reproduction trials. Intake, growth rate, and composition of body and organs of rats were measured. Rats in one trial were bred, their litters maintained on dietary treatments, and the offspring rebred. Treatment (FBCR vs. lime) x diet interactions on food composition and animal responses generally were not significant. Treatment had little effect on element composition of diets; mineral concentrations were in normal ranges. Diet treatment with FBCR depressed (P<0.01) food intake and growth of rats in one trial, but not in others, and had no effect (P<0.05) on body water, protein, ether extract, or gross energy composition. Some differences in element concentrations in the carcass and organs of rats and pups resulted from FBCR treatment, but effects were small and inconsistent. Litters from the first reproductive cycle appeared normal, except for animals fed the chicken + dietary FBCR treatment, on which pups showed poor growth and anemia. Offspring from certain diets were rebred and litters showed a high mortality, although this was not associated specifically with FBCR treatment. Results indicated no major detrimental effects on food composition, or growth, tissue element accumulation, and reproduction in the rat relating to use of FBCR as a soil amendment. 20 refs., 9 tabs.

Treatment of residual waters of slaughterhouses with filters

International Nuclear Information System (INIS)

Ortiz A, Jesus Mario

1995-01-01

For studying the anaerobic treatment of the residual waters coming from a slaughterhouse of bovine livestock, they were used a system of two filters in series and a third unique filter as witness. With values average of load organic volumetric and time of retention of 1.6 kg/(m 3 d) and 26 hours respectively, the efficiencies of removal of total DQO were similar in the unique filter and in the system in series, of the order of 64% on the average. Likewise, the retention and accumulation of biological solids in the channel were shown as the main road of removal of the DQO. The differentiation of the process achieved with the two filters in series allowed establishing that most of the accumulation happened in the primary filter, as long as the fundamental of the bioconversion in methane took place in the secondary filter of the system in series. The first relative level of methanegenization obtained could be explained by the limitations to the activity of the methanogenic biomass imposed by the low temperatures, although it could not discard a probable inhibition for the hydrolysis products of the accumulated fats

Tumorigenicity of sodium ascorbate in male rats.

Science.gov (United States)

Cohen, S M; Anderson, T A; de Oliveira, L M; Arnold, L L

1998-06-15

Sodium ascorbate, like other sodium salts such as saccharin, glutamate, and bicarbonate, produces urinary alterations when fed at high doses to rats, which results in mild superficial urothelial cytotoxicity and regeneration but not tumors in a standard 2-year bioassay. Sodium saccharin was shown to produce a low incidence of bladder tumors in rats if administered in a two-generation bioassay. In the present study, we evaluated sodium ascorbate in a two-generation bioassay that involved feeding to the male and female parental F344 rats for 4 weeks before mating, feeding the dams during gestation and lactation, and then feeding the weaned (at 28 days of age) male F1 generation rats for the remainder of their lifetime (up to 128 weeks of the experiment). Dietary levels of 1.0, 5.0, and 7.0% sodium ascorbate were tested. At 5.0 and 7.0% sodium ascorbate, there was an increase in urinary bladder urothelial papillary and nodular hyperplasia and the induction of a few papillomas and carcinomas. There was a dose-responsive increase in renal pelvic calcification and hyperplasia and inhibition of the aging nephropathy of rats even at the level of 1% sodium ascorbate. Because the short-term urothelial effects of sodium ascorbate in rats are inhibited by treatments producing urinary acidification to pH sodium ascorbate to evaluate the long-term effects. The combination of 7.0% sodium ascorbate plus 2.78% NH4Cl in the diet was toxic, and the group was terminated early during the course of the experiment. The group fed 5.0% sodium ascorbate plus 2.04% NH4Cl showed complete inhibition of the urothelial effects of sodium ascorbate and significant inhibition of its renal effects. We also demonstrated the presence of a calcium phosphate-containing urinary precipitate in rats fed sodium ascorbate at all doses, in a dose-responsive manner. The formation of the precipitate was inhibited by coadministration with NH4Cl. The proliferative effects of sodium ascorbate on the male rat

Inhibitin: a specific inhibitor of sodium/sodium exchange in erythrocytes.

OpenAIRE

Morgan, K; Brown, R C; Spurlock, G; Southgate, K; Mir, M A

1986-01-01

An inhibitor of ouabain-insensitive sodium/sodium exchange in erythrocytes has been isolated from leukemic promyelocytes. To explore the specific effects of this inhibitor, named inhibitin, sodium transport experiments were carried out in human erythrocytes. Inhibitin reduced ouabain-insensitive bidirectional sodium transport. It did not change net sodium fluxes, had no significant effect on rubidium influx, and did not inhibit sodium-potassium-ATPase activity. The inhibitory effect of inhibi...

Diminazene aceturate-sodium oleate complex for the treatment of ...

African Journals Online (AJOL)

The aim of this study is to improve the efficacy of diminazene aceturate via complex formation with sodium oleate. The complex was subjected to various in vitro and in vivo tests to assess its properties, toxicity and efficacy against Trypanosoma brucei brucei infections in comparison to pure drug. Results revealed that the ...

Residual sleep disturbance and risk of relapse during the continuation/maintenance phase treatment of major depressive disorder with the selective serotonin reuptake inhibitor fluoxetine

Directory of Open Access Journals (Sweden)

McGrath Patrick J

2010-02-01

Full Text Available Abstract Background Relapse of major depressive disorder (MDD is a common clinical problem. This study was designed to determine whether residual sleep disturbance (insomnia and hypersomnia predict risk of relapse during the continuation and maintenance treatment of MDD. Methods A total of 570 patients with MDD were treated with open-label, flexible dose fluoxetine (range 20 to 60 mg; mean dose = 45.8 mg/day; SD = 15.1 for 12 weeks. Under double blind conditions, 262 patients who achieved clinical response were randomly assigned to continue fluoxetine or to switch to placebo for 52 weeks or until relapse. Residual sleep disturbance during the baseline visit of the double-blind phase was assessed using items 4, 5, 6 (insomnia and 22, 23, 24 (hypersomnia of the Hamilton Depression Rating Scale (HDRS. Survival analysis was utilized to determine the effect of residual sleep disturbance on risk of relapse. Results The severities of early (P > 0.05, middle (P > 0.05, late (P > 0.05, or total (P > 0.05 residual insomnia were not found to significantly predict risk of relapse during continuation and maintenance-phase treatment. Similarly, the severities of early bedtime (P > 0.05, oversleeping (P > 0.05, napping (P > 0.05, or total (P > 0.05 residual hypersomnia were not found to significantly predict risk of relapse during continuation and maintenance-phase treatment. Conclusion The present study did not identify the severity of residual sleep disturbance among fluoxetine responders to predict risk of MDD relapse. The size of our sample may have precluded us from identifying more modest effects of residual sleep disturbance on the risk of relapse in MDD patients. Future studies are needed to further explore the relationship between residual sleep disturbance and relapse in MDD. Trial Registration ClinicalTrials.gov Identifier: NCT00427128

Association Between Pesticide Residue Intake From Consumption of Fruits and Vegetables and Pregnancy Outcomes Among Women Undergoing Infertility Treatment With Assisted Reproductive Technology.

Science.gov (United States)

Chiu, Yu-Han; Williams, Paige L; Gillman, Matthew W; Gaskins, Audrey J; Mínguez-Alarcón, Lidia; Souter, Irene; Toth, Thomas L; Ford, Jennifer B; Hauser, Russ; Chavarro, Jorge E

2018-01-01

Animal experiments suggest that ingestion of pesticide mixtures at environmentally relevant concentrations decreases the number of live-born offspring. Whether the same is true in humans is unknown. To examine the association of preconception intake of pesticide residues in fruits and vegetables (FVs) with outcomes of infertility treatment with assisted reproductive technologies (ART). This analysis included 325 women who completed a diet assessment and subsequently underwent 541 ART cycles in the Environment and Reproductive Health (EARTH) prospective cohort study (2007-2016) at a fertility center at a teaching hospital. We categorized FVs as having high or low pesticide residues using a validated method based on surveillance data from the US Department of Agriculture. Cluster-weighted generalized estimating equations were used to analyze associations of high- and low-pesticide residue FV intake with ART outcomes. Adjusted probabilities of clinical pregnancy and live birth per treatment cycle. In the 325 participants (mean [SD] age, 35.1 [4.0] y; body mass index, 24.1 [4.3]), mean (SD) intakes of high- and low-pesticide residue FVs were 1.7 (1.0) and 2.8 (1.6) servings/d, respectively. Greater intake of high-pesticide residue FVs was associated with a lower probability of clinical pregnancy and live birth. Compared with women in the lowest quartile of high-pesticide FV intake (<1.0 servings/d), women in the highest quartile (≥2.3 servings/d) had 18% (95% CI, 5%-30%) lower probability of clinical pregnancy and 26% (95% CI, 13%-37%) lower probability of live birth. Intake of low-pesticide residue FVs was not significantly related to ART outcomes. Higher consumption of high-pesticide residue FVs was associated with lower probabilities of pregnancy and live birth following infertility treatment with ART. These data suggest that dietary pesticide exposure within the range of typical human exposure may be associated with adverse reproductive consequences.

The analysis, by atomic-absorption spectrophotometry, of matte-leach residues

International Nuclear Information System (INIS)

Mallett, R.C.; Ring, E.J.; Middleton, H.R.; Dubois, M.

1973-01-01

Alternative methods for the analysis of matte-leach residues by atomic-absorption spectrophotometry were investigated. For the determination of the platinum-group metals, gold, and certain of the base metals, a fusion with sodium peroxide, followed by the separation of gold by reverse-phase chromatography and of the platinum-group metals by ion-exchange, is proposed. The noble metals are then determined in a solution that is free of most base metals including the sodium present as a result of the fusion. Copper, nickel, iron, calcium, magnesium, and aluminium can be determined after they have been removed from the ion-exchange column. Arsenic, selenium, tellurium, bismuth, tin, silver, lead, manganese, zinc, and cobalt can be determined in a separate sample after dissolution by a sealed-tube method. This is also an alternative method for the determination of copper, nickel, and iron. Chromium is determined separately after fusion with sodium peroxide, and silver can also be determined in this way. The laboratory method for these procedures is given as an appendix [af

Development of Sodium Technology for LMR

Energy Technology Data Exchange (ETDEWEB)

Kim, B. H.; Nam, H. Y.; Kim, T. J. (and others)

2007-03-15

In the experiments to investigate the characteristics of the free surface fluctuation in a vessel, the experimental correlation was modeled to describe the free surface fluctuation in the upper plenum of a liquid metal reactor within 95% reliability and 2.4% error. The correlation was used to verify the computational model. The new conceptual flowmeters were suggested to measure the sodium flow for the reliability enhancement. The electromagnetic flowmeter with permanent magnet showed a good linearity and repeatability. For reuse of the sodium contaminated component, CO{sub 2} bubbling method was developed. Sodium in 0.3mm crevice specimen was removed completely. The optimum condition for the used sodium treatment was deduced to estimate which reaction is more safe and adequate for operation condition by analyzing the reactivity alleviation condition and the reaction rate with the control of sodium hydroxide concentration A series of tests were carried out to investigate the enlargement rate of the nozzle hole itself and the sodium-water reaction temperature associated with needle-like jets of a high-pressure water/steam into the sodium side of a steam generator. The size of the nozzle hole became larger with an increased duration of the steam injection both for the 2.25Cr-1Mo and M9Cr-1Mo steels by a self-wastage phenomenon. For developing the SWR acoustic leak detection technology, the tool prepared by the LabVIEW was installed with the system, and confirmed the performance of the on-line acoustic leak detection tool using the SWR leak signal acquired in the KAERI facility.

Ultrasonic sweep arm for sodium cooled reactors

International Nuclear Information System (INIS)

Rohrbacher, H.A.; Bartholomay, R.

1975-05-01

This report describes experience in the use of a new type of monitoring and testing device to be applied in conjunction with components under sodium. In the method outlined, ultrasonic pulses are used which are emitted into the sodium plenum of fast breeder reactors by newly developed high temperature transducers. The basic work was conducted under out-of-pile conditions in a sodium tank of the sodium tank facility of the Karlsruhe Institute for Reactor Development. The sensor development, which preceded this phase, resulted in the use of soldered lithium niobate crystals whose operating characteristics were improved by the preliminary treatment outlined in the report. Special materials and techniques suitable for sensor fabrication are proposed. An alternative to soldering is suggested for contacting the crystals with their diaphragms, i.e. a contact pressure concept for the range of application up to 2 MHz. (orig.) [de

Clinical efficacy of pranoprofen and sodium hyaluronate for dry eye

Directory of Open Access Journals (Sweden)

Hong-Chao Hou

2016-01-01

Full Text Available AIM:To observe the clinical efficacy of pranoprofen and sodium hyaluronate for dry eye, and to provide the reference for clinical treatment of dry eye. METHODS: From January 2012 to January 2015 inour hospital, 106 patients with dry eye were tested and observed. In accordance with the number table, patients were divided into observation group and control group, 53 patients in the control group using conventional treatment plus single sodium hyaluronate eye drops, observation group using pranoprofen combined sodium hyaluronate eye drops, besides conventional treatment. Clinical outcomes between the two groups before and after treatments, dry eye score, fluorescein staining score, Schirmer I test and tear film break up time(BUTwere observed and analyzed. RESULTS:The effective rates of the two groups were 94.3%(50/53and 84.9%(45/53. Dry eye score of observation group before and after treatment were 3.24±0.52 and 0.32±0.06points, those of the control group were 3.26±0.48 and 0.75±0.24points. BUT of the experimental group before and after treatments were 5.67±3.052 and 12.95±2.865s, those of the control group were 6.23±2.985 and 9.85±2.714s.The differences between the two groups on the indicators above were statistically significant(PCONCLUSION: The combination of pranoprofen and sodium hyaluronate for the treatment of dry eye is effective, with high security and water holding capacity, which can improve the symptoms of dry eye and the patients' life quality.

Effects of mutagen application of sodium azide and gamma radiation in rice seeds

International Nuclear Information System (INIS)

Guimaraes, E.P.

1980-01-01

Effects of mutagen application of sodium azide and gamma radiation in rice seeds. Upland rice seeds, variety Dourado Precoce, were treated with gamma-rays and sodium azide(SA). Biological effects of these treatments were studied in the M 1 and M 2 generations. Survival number, seedling height, plant fertility and chlorophyill mutation frequencies based on mutations per 100 M 1 panicles and mutants per 100 M 2 seedlings were analysed. Among these characters, plant fertility was the most sensitive for mutagen treatments, and higher doses of gamma-rays or higher concentrations of sodium azide reduced significantly fertility of M 1 plants. The same effect as increase of concentration of sodium azide was observed when the acidity of buffer solution was increased, or when seeds were pre-treated in distilled water. The maximum chlorophyll mutation frequencies were obtained in sodium azide treatments: 40.74% in the M 1 panicles and 10.67% in the M 2 seedlings, in comparison with the maximum frequenies in gamma-irradiation of 10.39% in the M 1 panicles and 1.73% in the M 2 seedlings. (Author) [pt

Ontogenetic role of angiontensin-converting enzyme in rats: thirst and sodium appetite evaluation.

Science.gov (United States)

Mecawi, André S; Araujo, Iracema G; Rocha, Fábio F; Coimbra, Terezila M; Antunes-Rodrigues, José; Reis, Luís C

2010-01-12

We investigated the influence of captopril (an angiotensin converting enzyme inhibitor) treatment during pregnancy and lactation period on hydromineral balance of the male adult offspring, particularly, concerning thirst and sodium appetite. We did not observe significant alterations in basal hydromineral (water intake, 0.3M NaCl intake, volume and sodium urinary concentration) or cardiovascular parameters in adult male rats perinatally treated with captopril compared to controls. However, male offspring rats that perinatally exposed to captopril showed a significant attenuation in water intake induced by osmotic stimulation, extracellular dehydration and beta-adrenergic stimulation. Moreover, captopril treatment during perinatal period decreased the salt appetite induced by sodium depletion. This treatment also attenuated thirst and sodium appetite aroused during inhibition of peripheral angiotensin II generation raised by low concentration of captopril in the adult offspring. Interestingly, perinatal exposure to captopril did not alter water or salt intake induced by i.c.v. administration of angiotensin I or angiotensin II. These results showed that chronic inhibition of angiotensin converting enzyme during pregnancy and lactation modifies the regulation of induced thirst and sodium appetite in adulthood.

A comparison of two different formulations of diclofenac sodium 0.1% in the treatment of inflammation following cataract-intraocular lens surgery.

Science.gov (United States)

Mester, Ulrich; Lohmann, Chris; Pleyer, U; Steinkamp, G; Völcker, E; Kruger, H; Raj, Palaniswamy Sunder

2002-01-01

To compare the efficacy, tolerability and local tolerance of diclofenac sodium 0.1% containing hydroxypropylgamma cyclodextrin preserved with benzalkonium chloride 0.005% (Voltaren Ophtha CD), with that of diclofenac sodium 0.1% preserved with thiomersal 0.004% (Voltaren Ophtha) in the treatment of inflammation after cataract-intraocular lens surgery. Randomised 2:1, double-masked, parallel-group study in six centres in Germany. 299 patients scheduled to undergo phacoemulsification with posterior chamber intraocular lens implantation. Study medications were instilled four times in the 30 minutes before surgery and four times daily from the first postoperative day. The key efficacy variable was the reduction in anterior chamber flare (photons/millisecond) from day 1 to day 6 to 8. Patients underwent comprehensive ocular examinations, including laser flaremetry (KOWA), preoperatively and postoperatively at days 1, 6 to 8 and 24 to 32. 268 patients (Voltaren Ophtha CD 177, Voltaren Ophtha 91) completed the day 6 to 8 visit without any protocol violations. Reduction in the degree of intraocular inflammation with Voltaren Ophtha CD was equivalent to that achieved with Voltaren Ophtha at the day 6 to 8 [95% confidence interval (CI) -3.07 to +0.54] and day 24 to 32 (95% CI -1.44 to +1.40) visits. Although there was no significant (p = 0.464) difference between the two study groups in patients' global assessment of local tolerance at day 24 to 32, ocular discomfort was significantly (p = 0.023) less with Voltaren Ophtha CD compared with Voltaren Ophtha. Voltaren Ophtha CD was as effective and well tolerated but had less ocular discomfort compared with Voltaren Ophtha in the treatment of ocular inflammation after phacoemulsification with intraocular lens implantation. This new formulation of diclofenac sodium 0.1% may be used as an alternative to the existing formulations of ophthalmic diclofenac sodium 0.1%.

Immobilization of acid digestion residue

International Nuclear Information System (INIS)

Greenhalgh, W.O.; Allen, C.R.

1983-01-01

Acid digestion treatment of nuclear waste is similar to incineration processes and results in the bulk of the waste being reduced in volume and weight to some residual solids termed residue. The residue is composed of various dispersible solid materials and typically contains the resultant radioactivity from the waste. This report describes the immobilization of the residue in portland cement, borosilicate glass, and some other waste forms. Diagrams showing the cement and glass virtification parameters are included in the report as well as process steps and candidate waste product forms. Cement immobilization is simplest and probably least expensive; glass vitrification exhibits the best overall volume reduction ratio

Gamma-aminobutyric acid fermentation with date residue by a lactic acid bacterium, Lactobacillus brevis.

Science.gov (United States)

Hasegawa, Momoko; Yamane, Daisuke; Funato, Kouichi; Yoshida, Atsushi; Sambongi, Yoshihiro

2018-03-01

Dates are commercially consumed as semi-dried fruit or processed into juice and puree for further food production. However, the date residue after juice and puree production is not used, although it appears to be nutrient enriched. Here, date residue was fermented by a lactic acid bacterium, Lactobacillus brevis, which has been generally recognized as safe. Through degradation of sodium glutamate added to the residue during the fermentation, γ-aminobutyric acid (GABA), which reduces neuronal excitability, was produced at the conversion rate of 80-90% from glutamate. In order to achieve this GABA production level, pretreatment of the date residue with carbohydrate-degrading enzymes, i.e., cellulase and pectinase, was necessary. All ingredients used for this GABA fermentation were known as being edible. These results provide us with a solution for the increasing commercial demand for GABA in food industry with the use of date residue that has been often discarded. Copyright © 2017 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

Toltrazuril sulfone sodium salt: synthesis, analytical detection, and pharmacokinetics in the horse.

Science.gov (United States)

Dirikolu, L; Karpiesiuk, W; Lehner, A F; Tobin, T

2012-06-01

Toltrazuril sulfone (ponazuril) is a triazine-based antiprotozoal agent with clinical application in the treatment of equine protozoal myeloencephalomyelitis (EPM). In this study, we synthesized and determined the bioavailability of a sodium salt formulation of toltrazuril sulfone that can be used for the treatment and prophylaxis of EPM in horses. Toltrazuril sulfone sodium salt was rapidly absorbed, with a mean peak plasma concentration of 2400 ± 169 (SEM) ng/mL occurring at 8 h after oral-mucosal dosing and was about 56% bioavailable compared with the i.v. administration of toltrazuril sulfone in dimethylsulfoxide (DMSO). The relative bioavailability of toltrazuril sulfone suspended in water compared with toltrazuril sulfone sodium salt was 46%, indicating approximately 54% less oral bioavailability of this compound suspended in water. In this study, we also investigated whether this salt formulation of toltrazuril sulfone can be used as a feed additive formulation without significant reduction in oral bioavailability. Our results indicated that toltrazuril sulfone sodium salt is relatively well absorbed when administered with feed with a mean oral bioavailability of 52%. Based on these data, repeated oral administration of toltrazuril sulfone sodium salt with or without feed will yield effective plasma and cerebrospinal fluid (CSF) concentrations of toltrazuril sulfone for the treatment and prophylaxis of EPM and other protozoal diseases of horses and other species. As such, toltrazuril sulfone sodium salt has the potential to be used as feed additive formulations for both the treatment and prophylaxis of EPM and various other apicomplexan diseases. © 2011 Blackwell Publishing Ltd.

Adiabatic flame temperature of sodium combustion and sodium-water reaction

International Nuclear Information System (INIS)

Okano, Y.; Yamaguchi, A.

2001-01-01

In this paper, background information of sodium fire and sodium-water reaction accidents of LMFBR (liquid metal fast breeder reactor) is mentioned at first. Next, numerical analysis method of GENESYS is described in detail. Next, adiabatic flame temperature and composition of sodium combustion are analyzed, and affect of reactant composition, such oxygen and moisture, is discussed. Finally, adiabatic reaction zone temperature and composition of sodium-water reaction are calculated, and affects of reactant composition, sodium vaporization, and pressure are stated. Chemical equilibrium calculation program for generic chemical system (GENESYS) is developed in this study for the research on adiabatic flame temperature of sodium combustion and adiabatic reaction zone temperature of sodium-water reaction. The maximum flame temperature of the sodium combustion is 1,950 K at the standard atmospheric condition, and is not affected by the existence of moisture. The main reaction product is Na 2 O (l) , and in combustion in moist air, with NaOH (g) . The maximum reaction zone temperature of the sodium-water reaction is 1,600 K, and increases with the system pressure. The main products are NaOH (g) , NaOH (l) and H2 (g) . Sodium evaporation should be considered in the cases of sodium-rich and high pressure above 10 bar

Improving Corrosion Resistance and Biocompatibility of Magnesium Alloy by Sodium Hydroxide and Hydrofluoric Acid Treatments

Directory of Open Access Journals (Sweden)

Chang-Jiang Pan

2016-12-01

Full Text Available Owing to excellent mechanical property and biodegradation, magnesium-based alloys have been widely investigated for temporary implants such as cardiovascular stent and bone graft; however, the fast biodegradation in physiological environment and the limited surface biocompatibility hinder their clinical applications. In the present study, magnesium alloy was treated by sodium hydroxide (NaOH and hydrogen fluoride (HF solutions, respectively, to produce the chemical conversion layers with the aim of improving the corrosion resistance and biocompatibility. The results of attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR and X-ray photoelectron spectroscopy (XPS indicated that the chemical conversion layers of magnesium hydroxide or magnesium fluoride were obtained successfully. Sodium hydroxide treatment can significantly enhance the surface hydrophilicity while hydrogen fluoride treatment improved the surface hydrophobicity. Both the chemical conversion layers can obviously improve the corrosion resistance of the pristine magnesium alloy. Due to the hydrophobicity of magnesium fluoride, HF-treated magnesium alloy showed the relative better corrosion resistance than that of NaOH-treated substrate. According to the results of hemolysis assay and platelet adhesion, the chemical surface modified samples exhibited improved blood compatibility as compared to the pristine magnesium alloy. Furthermore, the chemical surface modified samples improved cytocompatibility to endothelial cells, the cells had better cell adhesion and proliferative profiles on the modified surfaces. Due to the excellent hydrophilicity, the NaOH-treated substrate displayed better blood compatibility and cytocompatibility to endothelial cells than that of HF-treated sample. It was considered that the method of the present study can be used for the surface modification of the magnesium alloy to enhance the corrosion resistance and biocompatibility.

Sodium in diet

Science.gov (United States)

Diet - sodium (salt); Hyponatremia - sodium in diet; Hypernatremia - sodium in diet; Heart failure - sodium in diet ... Too much sodium in the diet may lead to: High blood pressure in some people A serious buildup of fluid in people with heart failure , cirrhosis of ...

In situ Microscopic Observation of Sodium Deposition/Dissolution on Sodium Electrode

OpenAIRE

Yuhki Yui; Masahiko Hayashi; Jiro Nakamura

2016-01-01

Electrochemical sodium deposition/dissolution behaviors in propylene carbonate-based electrolyte solution were observed by means of in situ light microscopy. First, granular sodium was deposited at pits in a sodium electrode in the cathodic process. Then, the sodium particles grew linearly from the electrode surface, becoming needle-like in shape. In the subsequent anodic process, the sodium dissolved near the base of the needles on the sodium electrode and the so-called ?dead sodium? broke a...

Cover crop residue management for optimizing weed control

NARCIS (Netherlands)

Kruidhof, H.M.; Bastiaans, L.; Kropff, M.J.

2009-01-01

Although residue management seems a key factor in residue-mediated weed suppression, very few studies have systematically compared the influence of different residue management strategies on the establishment of crop and weed species. We evaluated the effect of several methods of pre-treatment and

On-treatment non-high-density lipoprotein cholesterol, apolipoprotein B, triglycerides, and lipid ratios in relation to residual vascular risk after treatment with potent statin therapy

DEFF Research Database (Denmark)

Mora, Samia; Glynn, Robert J; Boekholdt, S Matthijs

2012-01-01

The goal of this study was to determine whether residual risk after high-dose statin therapy for primary prevention individuals with reduced levels of low-density lipoprotein cholesterol (LDL-C) is related to on-treatment apolipoprotein B, non-high-density lipoprotein cholesterol (non-HDL-C), tri...

The influence of sodium-polyacrilic macromolecular chain length to the powder detergents secondary washing performances

Directory of Open Access Journals (Sweden)

Milojević Vladimir S.

2013-01-01

Full Text Available In order to investigate the influence of sodium-polyacrylate polymer as a co-builder in addition to the carbonate/zeolite builders in detergent builder system, secondary washing performances of powder laundry detergent containing equal percentage of sodium polyacrylate with the different weight average molar mass, Mw, have been examined. The value of the degree of whiteness, elongation at break, and total residue content are the most important secondary washing performances that significantly depend on sodium polyacrylates efficiency used as crystal inhibitors, stabilizers for suspended soil, and agents for soil redisposition prevention on fabric surface. The values of the whiteness and elongation at break for cotton fabrics increase with the increase of average weight molecular mass, Mw, up to the value of 70000 g/mol, while in the case of further increase of weight average molar mass up to the 250000 g/mol value of these characteristics begin to decline. The values of the total residue content after combustion indicate an increase in its content with the increase of weight average molar mass of 3000 to 70000 g/mol, while the highest value has been reached in the sample of detergent containing sodiumpolyacrilic with the weight average molar mass of 250000 g/mol. All detergent samples show no significant dependence of the secondary washing characteristics on the number of washing cycles.

Radioactive material in residues of health services residues

International Nuclear Information System (INIS)

Costa R, A. Jr.; Recio, J.C.

2006-01-01

The work presents the operational actions developed by the one organ responsible regulator for the control of the material use radioactive in Brazil. Starting from the appearance of coming radioactive material of hospitals and clinical with services of nuclear medicine, material that that is picked up and transported in specific trucks for the gathering of residuals of hospital origin, and guided one it manufactures of treatment of residuals of services of health, where they suffer radiological monitoring before to guide them for final deposition in sanitary embankment, in the city of Sao Paulo, Brazil. The appearance of this radioactive material exposes a possible one violation of the norms that govern the procedures and practices in that sector in the country. (Author)

Biocompatibility of acrylic resin after being soaked in sodium hypochlorite

Directory of Open Access Journals (Sweden)

Nike Hendrijatini

2009-06-01

Full Text Available Background: Acrylic resin as basic material for denture will stay on oral mucosa for a very long time. The polymerization of acrylic resin can be performed by conventional method and microwave, both produce different residual monomer at different toxicity. Acrylic resin can absorb solution, porous and possibly absorb disinfectantt as well, that may have toxic reaction with the tissue. Sodium Hypochlorite as removable denture disinfectant can be expected to be biocompatible to human body. The problem is how biocompatible acrylic resin which has been processed by conventional method and microwave method after being soaked in sodium hypochlorite solution. Purpose: The aim of this study was to understand in vitro biocompatibility of acrylic resin which has polimerated by conventional method and microwave after being soaked in sodium hypochlorite using tissue culture. Methods: Four groups of acrylic resin plate were produced, the first group was acrylic resin plate with microwave polymeration and soaked in sodium hypochlorite, the second group was acrylic resin plate with microwave polymeration but not soaked, the thirdwas one with conventional method and soaked and the last group was one with conventional method but not soaked, and in 1 control group. Each group consists of 7 plates. Biocompatibility test was performed in-vitro on each material using fibroblast tissue culture (BHK-21 cell-line. Result: The percentage between living cells and dead cells from materials which was given acrylic plate was wounted. The data was analyzed statistically with T test. Conclusion: The average value of living cells is higher in acrylic resin poimerization using microwave method compared to conventional method, in both soaked and non soaked (by sodium hypochlorite group. This means that sodium hypochlorite 0.5% was biocompatible to the mouth mucosa as removable denture disinfectant for 10 minutes soaking and washing afterwards.

Sodium pool fire analysis of sodium-cooled fast reactor by calculation

International Nuclear Information System (INIS)

Yu Hong; Xu Mi; Jin Degui

2002-01-01

Theoretical models were established according to the characteristic of sodium pool fire, and the SPOOL code was created independently. Some transient processes in sodium pool fire were modeled, including chemical reaction of sodium and oxygen; sodium combustion heat transfer modes in several kids of media; production, deposition and discharge of sodium aerosol; mass and energy exchange between different media in different ventilating conditions. The important characteristic parameters were calculated, such as pressure and temperature of gas, temperature of building materials, mass concentration of sodium aerosol, and so on. The SPOOL code, which provided available safety analysis tool for sodium pool fire accidents in sodium-cooled fast reactor, was well demonstrated with experimental data

Long-term stability of temocillin in dextrose 5% and in sodium chloride 0.9% polyolefin bags at 5 ± 3°C after freeze-thaw treatment.

Science.gov (United States)

Rolin, C; Hecq, J-D; Tulkens, P; Vanbeckbergen, D; Jamart, J; Galanti, L

2011-11-01

The aim of this study was to investigate the stability of a mixture of temocillin 20mg/ml in 5% dextrose and in 0.9% sodium chloride polyolefin bags after freezing, microwave thawing and long-term storage at 5±3°C. The stability of ten polyolefin bags containing 20mg/ml of temocillin, five bags in 5% dextrose and five bags in 0.9% sodium chloride, prepared under aseptic conditions was studied after freezing for 1 month at -20°C, thawing in a microwave oven with a validated cycle, and stored at 5±3°C. Over 30 days, temocillin concentrations were measured by high-pressure liquid chromatography. Visual inspections, microscope observation, spectrophotometric measurements and pH measurements were also performed. No precipitation occurred in the preparations but minor colour change was observed. No microaggregate was observed with optical microscopy or revealed by a change of absorbance. Based on a shelf life of 95% residual potency, temocillin infusions were stable at least 11 days in 5% dextrose and 14 days in 0.9% sodium chloride after freezing and microwave thawing (corresponding at the period where 95% lower confidence limit of the concentration-time profile remained superior to 95% of the initial concentration). During this period, the pH values of drug solutions have been observed to decrease without affecting chromatographic parameters. Within these limits, temocillin in 5% dextrose and in 0.9% sodium chloride infusions may be prepared and frozen in advance by a centralized intravenous admixture service then thawed before use in clinical units. Copyright © 2011 Elsevier Masson SAS. All rights reserved.

Study of the moderating effect of salts on the sodium-water reaction on the cleaning of irradiated fuel assemblies from fast neutron reactors, using fluid sodium heat transfer

International Nuclear Information System (INIS)

Lacroix, Marie

2014-01-01

Within the framework of the development of generation IV reactors one of the research tracks is related to the development of fast neutron reactors using fluid sodium heat transfer. The CEA (French Alternative Energies and Atomic Energy Commission) plans to build a prototype of reactor of this type called 'ASTRID'. To address development requirements for this prototype, research is in progress on the reactor's availability and in particular on the reduction of the washing duration for residual sodium fuel assemblies during their discharge. In fact, because sodium is very reactive with water (presently the only available process), the washing is done, for example, by very gradual addition. A solution currently being studied at the CEA and which is the subject of this thesis report consists of the addition of an aqueous salts solutions to the washing water in order to slow down the kinetic reaction. This doctoral dissertation describes the various salts, which have been evaluated and aims to explain their action mode. (author) [fr

The compatibility of various austenitic steels with molten sodium (1963); Compatibilite de divers aciers austenitiques avec le sodium fondu (1963)

Energy Technology Data Exchange (ETDEWEB)

Champeix, L; Sannier, J; Darras, R; Graff, W; Juste, P [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1963-07-01

Various techniques for studying corrosion by molten sodium have been developed and applied to the case of 18/10 austenitic steels. The results obtained are discussed as a function of various parameters: type of steel, temperature, oxygen content of the sodium, surface treatment, welds, mechanical strain. In general, these steels have an excellent resistance to sodium when the oxygen content is limited by a simple purification system of the 'cold trap' type, and when an attempt is made to avoid cavitation phenomena which are particularly dangerous, as is shown by the example given. (authors) [French] Des techniques d'etude de la corrosion par le sodium fondu en circulation ont ete mises au point et appliquees au cas des aciers austenitiques 18/10. Les resultats obtenus sont discutes en fonction de differents parametres: nuance de l'acier, temperature, teneur en oxygene du sodium, traitement de surface, soudure, contrainte mecanique. D'une maniere generale, ces aciers ont une excellente tenue dans le sodium lorsque, sa teneur en oxygene est limitee par un systeme simple de purification du type ''piege froid'' et lorsque l'on fait en sorte d'eviter les phenomenes de cavitation particulierement dangereux, comme il ressort d'un exemple cite. (auteurs)

Low sodium diet (image)

Science.gov (United States)

... for you. Look for these words on labels: low-sodium, sodium-free, no salt added, sodium-reduced, ... for you. Look for these words on labels: low-sodium, sodium-free, no salt added, sodium-reduced, ...

Scientific Opinion on the safety evaluation of the active substances, sodium carbonate peroxyhydrate coated with sodium carbonate and sodium silicate, bentonite, sodium chloride, sodium carbonate for use in active food contact materials

OpenAIRE

EFSA Panel on Food Contact Materials, Enzymes, Flavourings and Processing Aids (CEF)

2013-01-01

This scientific opinion of the Panel on Food Contact Materials, Enzymes, Flavourings and Processing Aids deals with the safety evaluation of the powder mixture of the active substances sodium carbonate peroxyhydrate coated with sodium carbonate and sodium silicate (FCM substance No 1009), bentonite (CAS No 1302-78-9, FCM No 393), sodium chloride (CAS No 7647-14-5, FCM No 985), sodium carbonate (CAS No 497-19-8, FCM No 1008) which are intended to be used as combined oxygen generator and carbon...

Advanced treatment of sodium dithionite wastewater using the combination of coagulation, catalytic ozonation, and SBR.

Science.gov (United States)

Zou, Xiao-Ling

2017-10-01

A combined process of coagulation-catalytic ozonation-anaerobic sequencing batch reactor (ASBR)-SBR was developed at lab scale for treating a real sodium dithionite wastewater with an initial chemical oxygen demand (COD) of 21,760-22,450 mg/L. Catalytic ozonation with the prepared cerium oxide (CeO 2 )/granular activated carbon catalyst significantly enhances wastewater biodegradability and reduces wastewater microtoxicity. The results show that, under the optimum conditions, the removal efficiencies of COD and suspended solids are averagely 99.3% and 95.6%, respectively, and the quality of final effluent can meet the national discharge standard of China. The coagulation and ASBR processes remove a considerable proportion of organic matter, while the SBR plays an important role in post-polish of final effluent. The ecotoxicity of the wastewater is greatly reduced after undergoing the hybrid treatment. This work demonstrates that the hybrid system has the potential to be applied for the advanced treatment of high-strength industrial wastewater.

Development of sodium disposal technology. Experiment of sodium compound solidification process

International Nuclear Information System (INIS)

Matsumoto, Toshiyuki; Ohura, Masato; Yatoh, Yasuo

2007-07-01

A large amount of sodium containing radioactive waste will come up at the time of final shutdown/decommission of FBR plant. The radioactive waste is managed as solid state material in a closed can in Japan. As for the sodium, there is no established method to convert the radioactive sodium to solid waste. Further, the sodium is highly reactive. Thus, it is recommended to convert the sodium to a stable substance before the solidification process. One of the stabilizing methods is conversion of sodium into sodium hydroxide solution. These stabilization and solidification processes should be safe, economical, and efficient. In order to develop such sodium disposal technology, nonradioactive sodium was used and a basic experiment was performed. Waste-fluid Slag Solidification method was employed as the solidification process of sodium hydroxide solution. Experimental parameters were mixing ratio of the sodium hydroxide and the slag solidification material, temperature and concentration of the sodium hydroxide. The best parameters were obtained to achieve the maximum filling ratio of the sodium hydroxide under a condition of enough high compressive strength of the solidified waste. In a beaker level test, the solidified waste was kept in a long term and it was shown that there was no change of appearance, density, and also the compressive strength was kept at a target value. In a real scale test, homogeneous profiles of the density and the compressive strength were obtained. The compressive strength was higher than the target value. It was shown that the Waste-fluid Slag Solidification method can be applied to the solidification process of the sodium hydroxide solution, which was produced by the stabilization process. (author)

Intermittent hormonal therapy in the treatment of post-irradiation residual/recurrent prostate cancer

International Nuclear Information System (INIS)

Williams, Aaron O; Kocherill, Paul G; Wallace, Michelle; Forman, Jeffrey D

1996-01-01

Purpose: To evaluate the efficacy and toxicity of intermittent hormonal therapy in the treatment of residual/recurrent prostate cancer. Materials and Methods: Seventeen patients with biochemical evidence of residual/recurrent prostate cancer were initially treated with radiation therapy (RT)(13), neo-adjuvant hormonal therapy and RT (3), or RT following prostatectomy (1). The mean follow-up time was 19.4 months from the initiation of hormonal therapy. Hormonal therapy consisted of an LH-RH agonist alone (7), an anti-androgen alone (1) or a combination of both (9). Hormonal therapy was continued until the prostatic specific antigen (PSA) level became undetectable. IHT was reinstituted when the PSA reached a pre-determined level, usually greater than or equal to 10ng/ml. Results: The mean time from completion of primary treatment to the initiation of hormonal therapy was 32.5 months. The mean PSA at the start of the first cycle of hormonal therapy was 43.9ng/ml, the second cycle, 11.9ng/ml and the third cycle, 24ng/ml. The mean PSA levels at the end of the first and second cycle of hormonal therapy were .48 and .42ng/ml, respectively. No patient has yet completed the third cycle of hormonal therapy. The average duration of hormonal therapy was 10 months for the first cycle and 4 months for the second cycle. The mean intermittent time off hormones were 9.3 months between cycles 1 and 2, and 10 months between cycles 2 and 3. No patient has yet become refractory to hormonal therapy. Currently all patients are alive. All patients experienced hot flashes and decreased libido at varying degrees during treatment. Thirty-five percent experienced gynecomastia. During the intervals between hormonal therapy, most patients reported a decrease in hot flashes. Conclusion: This analysis supplies preliminary evidence that intermittent hormonal therapy is a viable option in patients with biochemical evidence of disease following initial therapy. It is associated with less treatment

Electrometallurgical treatment of sodium-bonded spent nuclear fuel

International Nuclear Information System (INIS)

Benedict, R.W.; McFarlane, H.F.; Goff, K.M.

2001-01-01

For 20 years Argonne National Laboratory has been developing electrometallurgical technology for application to spent nuclear fuel. Progress has been rapid during the past 5 years as 1,6 tonnes spent fuel from the Experimental Breeder Reactor-II was treated and preparations were made for processing the remaining 25 tonnes of sodium-bonded fuel from the shutdown reactor. Two high level waste forms are being qualified for geologic disposal. Extension of the technology to oxide fuels or to actinide recycling has been on hold because of US policy on reprocessing. (author)

Fibrillar films obtained from sodium soap fibers and polyelectrolyte multilayers.

Science.gov (United States)

Zawko, Scott A; Schmidt, Christine E

2011-08-01

An objective of tissue engineering is to create synthetic polymer scaffolds with a fibrillar microstructure similar to the extracellular matrix. Here, we present a novel method for creating polymer fibers using the layer-by-layer method and sacrificial templates composed of sodium soap fibers. Soap fibers were prepared from neutralized fatty acids using a sodium chloride crystal dissolution method. Polyelectrolyte multilayers (PEMs) of polystyrene sulfonate and polyallylamine hydrochloride were deposited onto the soap fibers, crosslinked with glutaraldehyde, and then the soap fibers were leached with warm water and ethanol. The morphology of the resulting PEM structures was a dense network of fibers surrounded by a nonfibrillar matrix. Microscopy revealed that the PEM fibers were solid structures, presumably composed of polyelectrolytes complexed with residual fatty acids. These fibrillar PEM films were found to support the attachment of human dermal fibroblasts. Copyright © 2011 Wiley Periodicals, Inc.

Functionalized Fullerene Targeting Human Voltage-Gated Sodium Channel, hNav1.7.

Science.gov (United States)

Hilder, Tamsyn A; Robinson, Anna; Chung, Shin-Ho

2017-08-16

Mutations of hNa v 1.7 that cause its activities to be enhanced contribute to severe neuropathic pain. Only a small number of hNa v 1.7 specific inhibitors have been identified, most of which interact with the voltage-sensing domain of the voltage-activated sodium ion channel. In our previous computational study, we demonstrated that a [Lys 6 ]-C 84 fullerene binds tightly (affinity of 46 nM) to Na v Ab, the voltage-gated sodium channel from the bacterium Arcobacter butzleri. Here, we extend this work and, using molecular dynamics simulations, demonstrate that the same [Lys 6 ]-C 84 fullerene binds strongly (2.7 nM) to the pore of a modeled human sodium ion channel hNa v 1.7. In contrast, the fullerene binds only weakly to a mutated model of hNa v 1.7 (I1399D) (14.5 mM) and a model of the skeletal muscle hNa v 1.4 (3.7 mM). Comparison of one representative sequence from each of the nine human sodium channel isoforms shows that only hNa v 1.7 possesses residues that are critical for binding the fullerene derivative and blocking the channel pore.

C-Scan Performance Test of Under-Sodium ultrasonic Waveguide Sensor in Sodium

International Nuclear Information System (INIS)

Joo, Young Sang; Bae, Jin Ho; Kim, Jong Bum

2011-01-01

Reactor core and in-vessel structures of a sodium-cooled fast (SFR) are submerged in opaque liquid sodium in the reactor vessel. The ultrasonic inspection techniques should be applied for observing the in-vessel structures under hot liquid sodium. Ultrasonic sensors such as immersion sensors and rod-type waveguide sensors have developed in order to apply under-sodium viewing of the in-vessel structures of SFR. Recently the novel plate-type ultrasonic waveguide sensor has been developed for the versatile application of under-sodium viewing in SFR. In previous studies, the ultrasonic waveguide sensor module was designed and manufactured, and the feasibility study of the ultrasonic waveguide sensor was performed. To improve the performance of the ultrasonic waveguide sensor in the under-sodium application, a new concept of ultrasonic waveguide sensors with a Be coated SS304 plate is suggested for the effective generation of a leaky wave in liquid sodium and the non-dispersive propagation of A 0 -mode Lamb wave in an ultrasonic waveguide sensor. In this study, the C-scan performance of the under-sodium ultrasonic waveguide sensor in sodium has been investigated by the experimental test in sodium. The under-sodium ultrasonic waveguide sensor and the sodium test facility with a glove box system and a sodium tank are designed and manufactured to carry out the performance test of under-sodium ultrasonic waveguide sensor in sodium environment condition

Biogas systems for sisal and other agro-industrial residues

Energy Technology Data Exchange (ETDEWEB)

Jungersen, G [Danish Technological Inst., Section for Biotechnology, Taastrup (Denmark)

1998-12-31

Most of the East-African agro-industries are generating very large quantities of organic residues from production and processing of different crops. In the East-African Region the most important of these crops are: Sisal, Sugar, Coffee, Cashew nuts and Pineapple. In other 3. world countries, Palm oil and Cassava (Tapioca starch) processing are main producers of organic waste products. Moreover, large quantities of organic residues are generated from other food processing activities like breweries, consumption of bananas etc. The following pages give examples of setups and system designs of anaerobic treatment systems for some of the residues mentioned above. When considering anaerobic treatment of sisal residues, which constitutes the main agro-industrial biomass resource in Tanzania, two major issues should be considered: Optimal reactor set-up and performance; And optionally, potential methods for pre-treatment of fibre fraction in order to increase the methane yield. The sisal liquid residues are degraded very fast and efficiently in UASB systems. At COD loading rates less than 11 kg COD/m{sup 3} x day, the reduction in organic matter is more than 90% and methane yields obtained are between 373 and 377 ml CH{sub 4}/g COD reduced. The treatment of sisal solid residues in CSTR systems has been examined both at mesophilic (37 deg. C) and thermophilic temperatures (55 deg. C.). (EG)

Biogas systems for sisal and other agro-industrial residues

Energy Technology Data Exchange (ETDEWEB)

Jungersen, G. [Danish Technological Inst., Section for Biotechnology, Taastrup (Denmark)

1997-12-31

Most of the East-African agro-industries are generating very large quantities of organic residues from production and processing of different crops. In the East-African Region the most important of these crops are: Sisal, Sugar, Coffee, Cashew nuts and Pineapple. In other 3. world countries, Palm oil and Cassava (Tapioca starch) processing are main producers of organic waste products. Moreover, large quantities of organic residues are generated from other food processing activities like breweries, consumption of bananas etc. The following pages give examples of setups and system designs of anaerobic treatment systems for some of the residues mentioned above. When considering anaerobic treatment of sisal residues, which constitutes the main agro-industrial biomass resource in Tanzania, two major issues should be considered: Optimal reactor set-up and performance; And optionally, potential methods for pre-treatment of fibre fraction in order to increase the methane yield. The sisal liquid residues are degraded very fast and efficiently in UASB systems. At COD loading rates less than 11 kg COD/m{sup 3} x day, the reduction in organic matter is more than 90% and methane yields obtained are between 373 and 377 ml CH{sub 4}/g COD reduced. The treatment of sisal solid residues in CSTR systems has been examined both at mesophilic (37 deg. C) and thermophilic temperatures (55 deg. C.). (EG)

Sodium safety manual

International Nuclear Information System (INIS)

Hayes, D.J.; Gardiner, R.L.

1980-09-01

The sodium safety manual is based upon more than a decade of experience with liquid sodium at Berkeley Nuclear Laboratories (BNL). It draws particularly from the expertise and experience developed in the course of research work into sodium fires and sodium water reactions. It draws also on information obtained from the UKAEA and other sodium users. Many of the broad principles will apply to other Establishments but much of the detail is specific to BNL and as a consequence its application at other sites may well be limited. Accidents with sodium are at best unpleasant and at worst lethal in an extremely painful way. The object of this manual is to help prevent sodium accidents. It is not intended to give detailed advice on specific precautions for particular situations, but rather to set out the overall strategy which will ensure that sodium activities will be pursued safely. More detail is generally conveyed to staff by the use of local instructions known as Sodium Working Procedures (SWP's) which are not reproduced in this manual although a list of current SWP's is included. Much attention is properly given to the safe design and operation of larger facilities; nevertheless evidence suggests that sodium accidents most frequently occur in small-scale work particularly in operations associated with sodium cleaning and special care is needed in all such cases. (U.K.)

Feed Technology of Fibrous Sugarcane Residues for Ruminants

Directory of Open Access Journals (Sweden)

Kuswandi

2007-06-01

Full Text Available Abundant sugarcane residue during shortage of roughage in dry season gives an opportunity to raise ruminants around sugarcane industries. However, these products are not widely used by farmers due to an assumption that the usage is inefficient and that the feed utilization technology is not widely recognized. Sugarcane fibrous residues (tops, bagasse and pith may be a potential feed component if pre-treated to increase its digestion and consumption by the animal, and/or supplemented by other ingredients to balance nutrients in the rumen as well as those for production purpose. Digestibility can be increased by chemical treatments such as ammoniation and other alkaline treatments, whereas consumption can be increased by physical treatments such as grinding, hammermilling or pelleting. Nutrients that are missing in these fibrous residues can be provided by addition of urea, molasses and minerals for maintenance need, and bypass nutrients (carbohydrates, protein and fats that are digested in the small intestine and available for tissue or milk synthesis. There are three options for development of livestock agribusiness based on fibrous sugarcane residues; however, these require several technologies to optimize the utilization of these residues.

To4, the first Tityus obscurus β-toxin fully electrophysiologically characterized on human sodium channel isoforms.

Science.gov (United States)

Duque, Harry Morales; Mourão, Caroline Barbosa Farias; Tibery, Diogo Vieira; Barbosa, Eder Alves; Campos, Leandro Ambrósio; Schwartz, Elisabeth Ferroni

2017-09-01

Many scorpion toxins that act on sodium channels (NaScTxs) have been characterized till date. These toxins may act modulating the inactivation or the activation of sodium channels and are named α- or β-types, respectively. Some venom toxins from Tityus obscurus (Buthidae), a scorpion widely distributed in the Brazilian Amazon, have been partially characterized in previous studies; however, little information about their electrophysiological role on sodium ion channels has been published. In the present study, we describe the purification, identification and electrophysiological characterization of a NaScTx, which was first described as Tc54 and further fully sequenced and renamed To4. This toxin shows a marked β-type effect on different sodium channel subtypes (hNa v 1.1-hNa v 1.7) at low concentrations, and has more pronounced activity on hNa v 1.1, hNa v 1.2 and hNa v 1.4. By comparing To4 primary structure with other Tityus β-toxins which have already been electrophysiologically tested, it is possible to establish some key amino acid residues for the sodium channel activity. Thus, To4 is the first toxin from T. obscurus fully electrophysiologically characterized on different human sodium channel isoforms. Copyright © 2017 Elsevier Inc. All rights reserved.

The compatibility of various austenitic steels with molten sodium (1963)

International Nuclear Information System (INIS)

Champeix, L.; Sannier, J.; Darras, R.; Graff, W.; Juste, P.

1963-01-01

Various techniques for studying corrosion by molten sodium have been developed and applied to the case of 18/10 austenitic steels. The results obtained are discussed as a function of various parameters: type of steel, temperature, oxygen content of the sodium, surface treatment, welds, mechanical strain. In general, these steels have an excellent resistance to sodium when the oxygen content is limited by a simple purification system of the 'cold trap' type, and when an attempt is made to avoid cavitation phenomena which are particularly dangerous, as is shown by the example given. (authors) [fr

The effect of zeolite treatment by acids on sodium adsorption ratio of coal seam gas water.

Science.gov (United States)

Wang, Xiaoyu; Ozdemir, Orhan; Hampton, Marc A; Nguyen, Anh V; Do, Duong D

2012-10-15

Many coal seam gas (CSG) waters contain a sodium ion concentration which is too high relative to calcium and magnesium ions for environment acceptance. Natural zeolites can be used as a cheap and effective method to control sodium adsorption ratio (SAR, which is a measure of the relative preponderance of sodium to calcium and magnesium) due to its high cation exchange capacity. In this study, a natural zeolite from Queensland was examined for its potential to treat CSG water to remove sodium ions to lower SAR and reduce the pH value. The results demonstrate that acid activated zeolite at 30%wt solid ratio can reduce the sodium content from 563.0 to 182.7 ppm; the pH from 8.74 to 6.95; and SAR from 70.3 to 18.5. Based on the results of the batch experiments, the sodium adsorption capacity of the acid-treated zeolite is three times greater than that of the untreated zeolite. Both the untreated and acid-treated zeolite samples were characterized using zeta potential, surface characterization, DTA/TG and particle size distribution in order to explain their adsorption behaviours. Copyright © 2012 Elsevier Ltd. All rights reserved.

Thermal behaviour of nicotinic acid, sodium nicotinate and its compounds with some bivalent transition metal ions

Energy Technology Data Exchange (ETDEWEB)

Nascimento, A.L.C.S. do; Caires, F.J., E-mail: caires.flavio@yahoo.com.br; Gomes, D.J.C.; Gigante, A.C.; Ionashiro, M.

2014-01-10

Graphical abstract: - Highlights: • The transition metal ion nicotinates were synthesized. • The TG–DTA curves provided previously unreported information about thermal behaviour. • The gaseous products released were detected by TG–DSC coupled to FTIR. - Abstract: Solid-state M(L){sub 2}·nH{sub 2}O compounds, where M stands for bivalent transition metals (Mn, Fe, Co, Ni, Cu and Zn), L is nicotinate and n = 0–4.5, have been synthesized. Characterization and thermal behaviour of these compounds were investigated employing elemental analysis based on the mass losses observed in the TG–DTA curves, complexometry, X-ray diffractometry, infrared spectroscopy (FTIR), simultaneous thermogravimetric and differential thermal analysis (TG–DTA) and TG–DSC coupled to FTIR. The thermal behaviour of nicotinic acid and its sodium salt was also investigated. For the hydrated transition metal compounds, the dehydration and thermal decomposition of the anhydrous compounds occur in a single step. For the sodium nicotinate, the final residue up to 765 °C is sodium carbonate and for the transition metal nicotinates, the final residues are Mn{sub 3}O{sub 4}, Fe{sub 2}O{sub 3}, Co{sub 3}O{sub 4}, NiO, CuO and ZnO. The results also provided information concerning the thermal stability, thermal decomposition and identification of the gaseous products evolved during the thermal decomposition of the compounds.

Thermal behaviour of nicotinic acid, sodium nicotinate and its compounds with some bivalent transition metal ions

International Nuclear Information System (INIS)

Nascimento, A.L.C.S. do; Caires, F.J.; Gomes, D.J.C.; Gigante, A.C.; Ionashiro, M.

2014-01-01

Graphical abstract: - Highlights: • The transition metal ion nicotinates were synthesized. • The TG–DTA curves provided previously unreported information about thermal behaviour. • The gaseous products released were detected by TG–DSC coupled to FTIR. - Abstract: Solid-state M(L) 2 ·nH 2 O compounds, where M stands for bivalent transition metals (Mn, Fe, Co, Ni, Cu and Zn), L is nicotinate and n = 0–4.5, have been synthesized. Characterization and thermal behaviour of these compounds were investigated employing elemental analysis based on the mass losses observed in the TG–DTA curves, complexometry, X-ray diffractometry, infrared spectroscopy (FTIR), simultaneous thermogravimetric and differential thermal analysis (TG–DTA) and TG–DSC coupled to FTIR. The thermal behaviour of nicotinic acid and its sodium salt was also investigated. For the hydrated transition metal compounds, the dehydration and thermal decomposition of the anhydrous compounds occur in a single step. For the sodium nicotinate, the final residue up to 765 °C is sodium carbonate and for the transition metal nicotinates, the final residues are Mn 3 O 4 , Fe 2 O 3 , Co 3 O 4 , NiO, CuO and ZnO. The results also provided information concerning the thermal stability, thermal decomposition and identification of the gaseous products evolved during the thermal decomposition of the compounds

Research of nitroxynil residues in bovine milk following a single administration in the dry period by ultra-performance liquid chromatography tandem mass spectrometry

Directory of Open Access Journals (Sweden)

Claudia Chirollo

2013-10-01

Full Text Available Nitroxynil (NIT is a halogenated phenol used to control fascioliasis in cattle and sheep. The Commission Regulation EU No 37/2010 has established maximum residue limits for NIT in bovine and ovine muscle (400 μg kg−1, fat (200 μg kg−1, liver (20 μg kg−1 and kidney (400 μg kg−1, and more recently in bovine and ovine milk (20 μg kg−1. Thirty-five pregnant dairy cows were treated in this study with nitroxynil (340 mg/mL solution for injection at the recommended dose of 10 mg/kg body weight at the start of the dry period, i.e. 53 to 74 days before the expected calving. Calving occurred between 43 days and 79 days after treatment. The concentrations of NIT in the milk were monitored for up to 120 days after calving. NIT residues were extracted using acetonitrile; magnesium sulfate and sodium chloride were added to induce liquid-liquid partitioning and purified by dispersive solid phase extraction for clean-up. NIT was detected by ultra high performance liquid chromatography coupled to tandem mass spectrometry (UHPLC-MS/MS in negative ionization mode. The highest concentrations of this drug were found in two animals at the first milking, 48 and 53 day post treatment with levels of 362 and 657 μg kg–1, respectively. NIT residues were below the limit of detection of the method (0.24 μg/kg–1 between 67 and 106 day post-treatment. Following calving, residues rapidly depleted in animals and were non-detectable from 10 to 38 days post-calving. In particular, in all animals milk resulted compliant (<20 μg/kg−1 three days post partum.

Thermal and chemical interaction of hot liquid sodium with limestone concrete in argon atmosphere

International Nuclear Information System (INIS)

Fakir, Charan Parida; Sanjay, Kumar Das; Anil, Kumar Sharma; Ramesh, S.S.; Somayajulu, P.A.; Malarvizhi, B.; Kasinathan, N.; Rajan, M.

2007-01-01

Sodium cooled fast breeder reactors (FBRs) may experience accidental leakage of hot liquid sodium in the inert equipment cells and reactor cavity. The leaked sodium at temperature ranging from 120degC to 550degC can come in contact with the sacrificial layer of limestone concrete. In order to study the thermal and chemical impact of sodium on the limestone concrete, five experimental runs were carried out under different test conditions simulating accident scenarios as realistically as possible. In each experimental run, a given mass of liquid sodium preheated to a specified temperature was dumped on the surface of concrete specimen housed in a test vessel with argon atmosphere. The sodium pool formed on the concrete was heated with an immersion heater to maintain the pool temperature at pre-selected level. The temperatures at various strategic locations were continuously monitored throughout the test run. Online measurement of pressure, hydrogen gas and oxygen gas in argon atmosphere was conducted. The solid samples of sodium debris were retrieved from the posttest concrete specimen by manual core drilling device for chemical analysis of reacted and un-reacted sodium. After cleaning the sodium debris, a power-drilling machine was employed to collect powder samples at regular depth interval from the concrete block floor to determine residual free and bound water. This paper presents some of the dominant thermal and chemical features related to structural safety of the concrete. Among the thermal parameters, on-set time and residence period for Energetic Thermal Transients (ETT) along with peak and average heat generation rates are evaluated. Chemical parameters such as rate and extent of water release from concrete, sodium consumption, sodium hydroxide production and sodium emission into argon atmosphere are also elucidated. Physicochemical characteristics of post-test sodium and concrete debris were investigated. Moreover spatial distribution of sodium, free and

Relatively rapid loss of lampricide residues from fillet tissue of fish after routine treatment

Science.gov (United States)

Vue, C.; Bernardy, J.A.; Hubert, T.D.; Gingerich, W.H.; Stehly, G.R.

2002-01-01

The selective sea lamprey (Petromyzon marinus) larvicide 3-trifluoromethyl-4-nitrophenol (TFM) is currently used to control parasitic sea lampreys in tributaries to the Great Lakes basin. The concentration and persistence of TFM and its major metabolite, TFM glucuronide (TFM-glu), was determined in fillet tissue of fish after a typical stream application. Rainbow trout (Oncorhynchus mykiss) and channel catfish (Ictalurus punctatus) were exposed to a nominal concentration of 12.6 nmol/mL TFM for about 12 h during a sea lamprey control treatment of the Ford River in Michigan. Concentrations of TFM and TFM-glu were greatest in the fillet tissues during the exposure period, with greater residues in channel catfish (wet wt; mean, 6.95 nmol/g TFM; mean, 2.40 nmol/g TFM-glu) than in rainbow trout (wet wt; mean, 1.45 nmol/g TFM; mean, 0.93 nmol/g TFM-glu). After the exposure period, residues in both species decreased by 90-99% within 6-12 h and were less than the quantitation limit (<0.03 nmol/g) within 36 h.

Handling of Solid Residues

International Nuclear Information System (INIS)

Medina Bermudez, Clara Ines

1999-01-01

The topic of solid residues is specifically of great interest and concern for the authorities, institutions and community that identify in them a true threat against the human health and the atmosphere in the related with the aesthetic deterioration of the urban centers and of the natural landscape; in the proliferation of vectorial transmitters of illnesses and the effect on the biodiversity. Inside the wide spectrum of topics that they keep relationship with the environmental protection, the inadequate handling of solid residues and residues dangerous squatter an important line in the definition of political and practical environmentally sustainable. The industrial development and the population's growth have originated a continuous increase in the production of solid residues; of equal it forms, their composition day after day is more heterogeneous. The base for the good handling includes the appropriate intervention of the different stages of an integral administration of residues, which include the separation in the source, the gathering, the handling, the use, treatment, final disposition and the institutional organization of the administration. The topic of the dangerous residues generates more expectation. These residues understand from those of pathogen type that are generated in the establishments of health that of hospital attention, until those of combustible, inflammable type, explosive, radio-active, volatile, corrosive, reagent or toxic, associated to numerous industrial processes, common in our countries in development

Urinary Sodium and Potassium Excretion and Dietary Sources of Sodium in Maputo, Mozambique

Directory of Open Access Journals (Sweden)

Ana Queiroz

2017-08-01

Full Text Available This study aimed to evaluate the urinary excretion of sodium and potassium, and to estimate the main food sources of sodium in Maputo dwellers. A cross-sectional evaluation of a sample of 100 hospital workers was conducted between October 2012 and May 2013. Sodium and potassium urinary excretion was assessed in a 24-h urine sample; creatinine excretion was used to exclude unlikely urine values. Food intake in the same period of urine collection was assessed using a 24-h dietary recall. The Food Processor Plus® was used to estimate sodium intake corresponding to naturally occurring sodium and sodium added to processed foods (non-discretionary sodium. Salt added during culinary preparations (discretionary sodium was computed as the difference between urinary sodium excretion and non-discretionary sodium. The mean (standard deviation urinary sodium excretion was 4220 (1830 mg/day, and 92% of the participants were above the World Health Organization (WHO recommendations. Discretionary sodium contributed 60.1% of total dietary sodium intake, followed by sodium from processed foods (29.0% and naturally occurring sodium (10.9%. The mean (standard deviation urinary potassium excretion was 1909 (778 mg/day, and 96% of the participants were below the WHO potassium intake recommendation. The mean (standard deviation sodium to potassium molar ratio was 4.2 (2.4. Interventions to decrease sodium and increase potassium intake are needed in Mozambique.

Management of municipal solid waste incineration residues

International Nuclear Information System (INIS)

Sabbas, T.; Polettini, A.; Pomi, R.; Astrup, T.; Hjelmar, O.; Mostbauer, P.; Cappai, G.; Magel, G.; Salhofer, S.; Speiser, C.; Heuss-Assbichler, S.; Klein, R.; Lechner, P.

2003-01-01

The management of residues from thermal waste treatment is an integral part of waste management systems. The primary goal of managing incineration residues is to prevent any impact on our health or environment caused by unacceptable particulate, gaseous and/or solute emissions. This paper provides insight into the most important measures for putting this requirement into practice. It also offers an overview of the factors and processes affecting these mitigating measures as well as the short- and long-term behavior of residues from thermal waste treatment under different scenarios. General conditions affecting the emission rate of salts and metals are shown as well as factors relevant to mitigating measures or sources of gaseous emissions

Effect of sodium aescinate treatment on PCOS rat model with insulin resistance.

Science.gov (United States)

Chen, L; Hu, L M; Wang, Y F; Yang, H Y; Huang, X Y; Zhou, W; Sun, H X

2017-01-01

Recent studies indicated that insulin resistance may contribute to the pathogenesis of polycystic ovary syndrome (PCOS); however, the specific mechanism is still unclear. To investigate the effect of sodium aescinate (SA) on PCOS-IR rat models. Sixty rats were randomly divided into the five groups: un-treated rats (n = 12), PCOS-IR group (n = 12), PCOS-IR group plus 50 mg/kg SA (n = 12), PCOS-IR group plus 10 mg/kg SA (n = 12), PCOS-IR group plus 150 mg/kg metformin (n = 12). On day 21, rats were sacrificed, and H(and)E staining was performed for histopathologic examination of the ovaries; moreover, the serum level of follicle-stimulating hormone (FSH), testosterone, and luteotropic hormone (LH) were measured, and the expression as well as phosphorylation of PI3K, Akt and Gsk-3β were examined using western blot assay. High dosage of SA treatment improved the morphological features of the ovaries in PCOS rats, and also induced significant decrease in serum expression of testosterone and LH/FSH ratio and significant decrease in the expression of p-PI3K, p-Akt and p-Gsk-3β. Our results demonstrated that SA treatment could alleviate the symptom of PCOS in rat model through regulating the PI3K/Akt/GSK3-β pathway (Fig. 4, Ref. 22).

Residual stress by repair welds

International Nuclear Information System (INIS)

Mochizuki, Masahito; Toyoda, Masao

2003-01-01

Residual stress by repair welds is computed using the thermal elastic-plastic analysis with phase-transformation effect. Coupling phenomena of temperature, microstructure, and stress-strain fields are simulated in the finite-element analysis. Weld bond of a plate butt-welded joint is gouged and then deposited by weld metal in repair process. Heat source is synchronously moved with the deposition of the finite-element as the weld deposition. Microstructure is considered by using CCT diagram and the transformation behavior in the repair weld is also simulated. The effects of initial stress, heat input, and weld length on residual stress distribution are studied from the organic results of numerical analysis. Initial residual stress before repair weld has no influence on the residual stress after repair treatment near weld metal, because the initial stress near weld metal releases due to high temperature of repair weld and then stress by repair weld regenerates. Heat input has an effect for residual stress distribution, for not its magnitude but distribution zone. Weld length should be considered reducing the magnitude of residual stress in the edge of weld bead; short bead induces high tensile residual stress. (author)

Assessment of flow induced vibration in a sodium-sodium heat exchanger

Energy Technology Data Exchange (ETDEWEB)

Prakash, V. [Fast Reactor Technology Group, Indira Gandhi Centre for Atomic Research, Kalpakkam, Tamil Nadu (India)], E-mail: prakash@igcar.gov.in; Thirumalai, M.; Prabhakar, R.; Vaidyanathan, G. [Fast Reactor Technology Group, Indira Gandhi Centre for Atomic Research, Kalpakkam, Tamil Nadu (India)

2009-01-15

The 500 MWe Prototype Fast Breeder Reactor (PFBR) is under construction at Kalpakkam. It is a liquid metal sodium cooled pool type fast reactor with all primary components located inside a sodium pool. The heat produced due to fission in the core is transported by primary sodium to the secondary sodium in a sodium to sodium Intermediate Heat Exchanger (IHX), which in turn is transferred to water in the steam generator. PFBR IHX is a shell and tube type heat exchanger with primary sodium on shell side and secondary sodium in the tube side. Since IHX is one of the critical components placed inside the radioactive primary sodium, trouble-free operation of the IHX is very much essential for power plant availability. To validate the design and the adequacy of the support system provided for the IHX, flow induced vibration (FIV) experiments were carried out in a water test loop on a 60 deg. sector model. This paper discusses the flow induced vibration measurements carried out in 60 deg. sector model of IHX, the modeling criteria, the results and conclusion.

Alendronate sodium hydrate (oral jelly for the treatment of osteoporosis: review of a novel, easy to swallow formulation

Directory of Open Access Journals (Sweden)

Imai K

2013-06-01

Full Text Available Kazuhiro Imai Department of Life Sciences, Graduate School of Arts and Sciences, The University of Tokyo, Tokyo, Japan Abstract: Osteoporosis is a skeletal disorder characterized by loss of bone mass, decreased bone strength, and an increased risk of bone fracture. The disease progresses with age, especially in postmenopausal women. Japan is one of the most rapidly aging societies worldwide. Japanese individuals over 65 years of age constituted 23.0% of the population in 2010 and 25.1% to 25.2% as of 2013. The estimated number of people with osteoporosis in Japan is currently 13 million. Bisphosphonates increase bone mineral density by inhibiting osteoclast-mediated bone resorption, thereby reducing the risk of fractures. Alendronate sodium hydrate (alendronate is a bisphosphonate that potently inhibits bone resorption and is used to treat osteoporosis. Sufficient water is required to take an alendronate oral tablet; insufficient water could result in digestive system diseases, such as esophageal ulceration. Elderly patients with swallowing difficulty may choke on the tablet. Taking a tablet with oral jelly is a method to prevent digestive system disease and reduce the choking hazard. Once-weekly alendronate oral jelly was approved in 2012 by the Ministry of Health, Labour, and Welfare of Japan as the world's first drug for osteoporosis in a jelly formulation. It consists of a jelly portion and an air portion. The jelly formulation is smoothly discharged by pushing the air portion. Therefore, elderly patients with physical disabilities are able to easily take all of the jelly formulation from the package. In this review, this new formulation of alendronate sodium hydrate (oral jelly is introduced and discussed in terms of osteoporosis treatment. This new formulation provides an alternative so that patients may select a method of dosing tailored to their preferences. Management of osteoporosis involves assessing fracture risk and preventing

Carbaryl residues in maize and processed products

International Nuclear Information System (INIS)

Qureshi, M.J.; Sattar, A. Jr.; Naqvi, M.H.

1981-01-01

Carbaryl residues in two local maize varieties were determined using a colorimetric method. No significant differences were observed for residues of the two varieties which ranged between 12.0 to 13.75 mg/kg in the crude oil, and averaged 1.04 and 0.67 mg/kg in the flour and cake respectively. In whole maize plants, carbaryl residues declined to approximately 2 mg/kg 35 days after treatment. Cooking in aqueous, oil or aqueous-oil media led to 63-83% loss of carbaryl residues, after 30 minutes. (author)

Sodium vapor deposition onto a horizontal flat plate above liquid sodium surface, (3)

International Nuclear Information System (INIS)

Kudo, Kazuhiko; Hirata, Masaru.

1978-01-01

Sodium vapour and sodium mist in the cover gas of a sodium system of a fast breeder reactor cause various problems. In this report, with the results of measurements of sodium mist concentration, the distribution of sodium mist diameter in cover gas was analytically obtained. The analysis was made by using the different nucleus model B. The measurement of the concentration of sodium mist was carried out with a sodium mist pot designed by the author. The experiment was done at the sodium temperature of 400 and 500 degree centigrade. The relations among sodium temperature, upper wall temperature, and the sodium mist concentration in cover gas were obtained. Evaluation of effective condensed nuclear radius in the cover gas was made by the comparison of analysis and experimental results. The results of this evaluation shows the following conclusions. It is impossible to express the distribution of sodium mist diameter by normal distribution or logarithmic normal distribution. Drop of sodium temperature results in the decrease of weight mean radius of generated sodium mist. Drop of upper wall temperature causes the decrease of weight mean radius, and increases sodium mist concentration. (Kato, T.)

An investigation of sodium iodide solubility in sodium-stainless steel systems

International Nuclear Information System (INIS)

Sagawa, Norihiko; Tashiro, Suguru

1996-01-01

Sodium iodide and major constituents of stainless steel in sodium are determined by using the steel capsules to obtain a better understanding on contribution of the constituents to the apparent iodide solubility in sodium. The capsule loaded with 20 g sodium and 0.1 - 0.3 g powder of sodium iodide is heated at its upper part in a furnace and cooled at its bottom on brass plates to establish a large temperature gradient along the capsule tube. After a given period of equilibration, the iodide and constituents are fixed in solidified sodium by quick quenching of the capsules. Sodium samples are taken from the sectioned capsule tube and submitted to sodium dissolution by vaporized water for determination of the iodine and to vacuum distillation for determination of the metal elements. Iron and nickel concentrations are observed to be lower in the samples at higher iodine concentrations. Chromium and manganese concentrations are seen to be insensitive to the iodine concentrations. The observations can be interpreted by a model that sodium oxide combines with metal iodide in sodium to form a complex compound and with consideration that the compound will fall and deposit onto the bottom of the capsule by thermal diffusion. (author)

49 CFR 173.189 - Batteries containing sodium or cells containing sodium.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Batteries containing sodium or cells containing sodium. 173.189 Section 173.189 Transportation Other Regulations Relating to Transportation PIPELINE AND... Than Class 1 and Class 7 § 173.189 Batteries containing sodium or cells containing sodium. (a...

A 23Na Multiple-Quantum-Filtered NMR Study of the Effect of the Cytoskeleton Conformation on the Anisotropic Motion of Sodium Ions in Red Blood Cells

Science.gov (United States)

Knubovets, Tatyana; Shinar, Hadassah; Eliav, Uzi; Navon, Gil

1996-01-01

Recently, it has been shown that23Na double-quantum-filtered NMR spectroscopy can be used to detect anisotropic motion of bound sodium ions in biological systems. The technique is based on the formation of the second-rank tensor when the quadrupolar interaction is not averaged to zero. Using this method, anisotropic motion of bound sodium in human and dog red blood cells was detected, and the effect was shown to depend on the integrity of the membrane cytoskeleton. In the present study, multiple-quantum-filtered techniques were applied in combination with a quadrupolar echo to measure the transverse-relaxation times,T2fandT2s. Line fitting was performed to obtain the values of the residual quadrupolar interaction, which was measured for sodium in a variety of mammalian erythrocytes of different size, shape, rheological properties, and sodium concentrations. Human unsealed white ghosts were used to study sodium bound at the anisotropic sites on the inner side of the RBC membrane. Modulations of the conformation of the cytoskeleton by the variation of either the ionic strength or pH of the suspending medium caused drastic changes in both the residual quadrupolar interaction andT2fdue to changes in the fraction of bound sodium ions as well as changes in the structure of the binding sites. By combining the two spectroscopic parameters, structural change can be followed. The changes in the structure of the sodium anisotropic binding sites deduced by this method were found to correlate with known conformational changes of the membrane cytoskeleton. Variations of the medium pH affected both the fraction of bound sodium ions and the structure of the anisotropic binding sites. Sodium and potassium were shown to bind to the anisotropic binding sites with the same affinity.

Effects of Adopting Different Kinds of Collecting Method for Years on Film Residual Coefficient and Maize Yields

Directory of Open Access Journals (Sweden)

TANG Wen-xue

2017-03-01

Full Text Available Wide usage of mulching technology has increased crop yields, but the large amounts of mulching film residue resulting from widespread use of plastic film in China has brought about a series of pollution hazards. Based on a 4-year (2011-2014 long-term experiment, the effects of different kinds of collecting mothod (zero plastic film residues, conventional plastic film residues, whole plastic film residues remainded on plastic film residues, residual coefficient and maize yield were explored. Plastic film residues mainly remained in 0~10 cm, 10~20 cm soil layers. In 0~30 cm soil layers, the two types of mulch residues (>25 cm2, 4~25 cm2 under zero plastic film residues treatment were much less than conventional plastic film residues and whole plastic film residues remainded treatments, no significant differences were observed in the mulch residues (2 among 3 treatments. After maize harvest, the amount of plastic film residues under zero plastic film residues, conventional plastic film residues and whole plastic film residues remainded treatments were 52.71, 80.85 kg·hm-2 and 152.65 kg·hm-2, respectively, the residual coefficient for zero plastic film residues, conventional plastic film residues and whole plastic film residues remainded treatments were -9.45%, 8.53% and 54.42%, respectively. The stem diameter, ear length, ear width, ear row number, grain number per row and 100-grain weight of maize decreased with the increase of residual film amount. Compared with the conventional plastic film residues, the mean grain yield of whole plastic film residues remainded treatment decreased by 15.08%, whereas the zero plastic film residues treatment increased by 4.70%. The plastic film residues, residual coefficient and maize yield were comprehensively analyzed, the conventional plastic film residues practice should be adopted currently without appropriate plastic film residues collector. But from the long-term development, we should speed up the

Aluminum-based water treatment residual use in a constructed wetland for capturing urban runoff phosphorus: Column study

Science.gov (United States)

Aluminum-based water treatment residuals (Al-WTR) have a strong affinity to sorb phosphorus. In a proof-of-concept greenhouse column study, Al-WTR was surface-applied at 0, 62, 124, and 248 Mg/ha to 15 cm of soil on top of 46 cm of sand; Al-WTR rates were estimated to capture 0, 10, 20, and 40 year...

Replacement of 5% of OPC by fly ash and APC residues from MSWI with electrodialytic pre-treatment

DEFF Research Database (Denmark)

Magro, Cátia; Kirkelund, Gunvor Marie; Guedes, Paula

2016-01-01

as pre-treatment prior to incorporation in mortar, aiming to stabilize and remove HM and chlorides. Eight ED experiments were performed for 7 days with a L/S ratio of 3.5. The number of compartments (2 or 3) and current density (0.1 or 1.0 mA cm-2) varied. After ED treatment the heavy metals left...... in the ash were not leached to the same extent as in the original ash. In mortar 5% of Ordinary Portland Cement was replaced by FA and APC residues (raw and ED upgraded). The studied parameters: compressive strength, HM leachability, and Cl content. The ED pre-treatment resulted in a decrease in both...

Indirect spectrophotometric determination of sodium ceftriaxone with n-propyl alcohol-ammonium sulfate-water system by extraction flotation of copper(II).

Science.gov (United States)

Zhao, Wei; Zhang, Yan; Li, Quanmin

2008-05-01

Although the determination methods of sodium ceftriaxone has been increasingly reported, these methods have their inherent limits preventing them from being broadly applied in common laboratories. In order to circumvent this problem, a rapid and simple method for the indirect spectrophotometric determination of sodium ceftriaxone is reported. Sodium ceftriaxone was degraded completely in the presence of 0.20 mol/l sodium hydroxide in boiling water bath for 20 min. The thiol group (-SH) of the degradation product (I) of sodium ceftriaxone could reduce cupric to cuprous ions, and the resulting which was precipitated with the thiol group (-SH) of the degradation product (II) at pH 4.0. By determining the residual amount of copper (II), the indirect determination of sodium ceftriaxone can be achieved. Standard curve of sodium ceftriaxone versus the flotation yield of copper(II) showed that sodium ceftriaxone could be determined in low concentrations. The linear range of sodium ceftriaxone was 0.70-32 microg/ml and the detection limit evaluated by calibration curve (3sigma/k) was found to be 0.60 microg/ml. A simple and efficient method was developed and it has been successfully applied to the determination of sodium ceftriaxone in human serum and urine samples, respectively. It is expected that this method will find broad applications in the detection of cephalosporin derivatives with similar structure.

Cavitation erosion in sodium flow, sodium cavitation tunnel testing

International Nuclear Information System (INIS)

Courbiere, Pierre.

1981-04-01

The high-volume sodium flows present in fast neutron reactors are liable to induce cavitation phenomena in various portion of the sodium lines and pumps. The absence of sufficient data in this area led the C.E.A. to undertake an erosion research program in cavitating sodium flow. This paper discusses the considerations leading to the definition and execution of sodium cavitation erosion tests, and reviews the tests run with 400 0 C sodium on various steel grades: 316, 316 L, 316 Ti (Z8CNDT17-12), Poral (Z3CND18-12), 304 L and LN2 - clad 316 L (Ni coating-clad 316 L). Acoustic detection and signal processing methods were used with an instrument package designed and implemented at the Cadarache Nuclear Research Center

Temperature Field Prediction for Determining the Residual Stresses Under Heat Treatment of Aluminum Alloys

Directory of Open Access Journals (Sweden)

A. V. Livshits

2014-01-01

Full Text Available The article is devoted to non-stationary temperature field blanks from aluminum alloys during heat treatment. It consists of the introduction and two smaller paragraphs. In the introduction the author concerns the influence of residual stresses arising in the manufacturing process of details, on the strength of the whole aircraft construction and, consequently, on their technical and economic parameters, such as weight, reliability, efficiency, and cost. He also notes that the residual stresses appeared during the production of parts change their location, size and direction under the influence of the elastic deformations that occur during the exploitation of aircraft. Redistributed residual stresses may have a chaotic distribution that may cause overlap of these stresses on the stresses caused by the impact of workload of constructions and destruction or damage of aircraft components.The first paragraph is devoted to the existing methods and techniques for determining the residual stresses. The presented methods and techniques are analyzed to show the advantages and disadvantages of each of them. The conclusion is drawn that the method to determine the residual stresses is necessary, its cost is less than those of existing ones, and an error does not exceed 10%.In the second section, the author divides the problem of determining the residual stresses into two parts, and describes the solution methods of the first one. The first problem is to define the temperature field of the work piece. The author uses a Fourier equation with the definition of initial and boundary conditions to describe a mathematical model of the heat cycle of work piece cooling. He draws special attention here to the fact that it is complicated to determine the heat transfer coefficient, which characterizes the process of cooling the work piece during hardening because of its dependence on a number of factors, such as changing temperature-dependent material properties of

Preliminary Results on a Contact between 4 kg of Molten UO2 and Liquid Sodium

International Nuclear Information System (INIS)

Amblard, M.

1976-01-01

The CORECT II Experiment consists in simulating the penetration of sodium into an assembly when the fuel is molten. In other words, it is a shock-tube type of experiment with dimensions representative of a full-scale assembly. the experiment consists in dropping a 100 litre column of sodium onto partially molten UO 2 . The following measurements are carried out in transient regime: - sodium velocity in the column; - pressure in the interaction chamber; - pressures at the bottom and at the top of a 5 m tube; - pressure in the argon blanket. The experimental parameters are: - the mass of UO 2 involved (about 4 or 7 kg of 80% molten UO 2 ); - the initial temperature of the sodium (up to 700 deg. C); - the pressure of the residual gas in the interaction chamber during the fall of the sodium; - the dimensions of the interaction chamber and the sodium supply tube; - the form of contact between the UO 2 and the sodium (the sodium may fall on partially liquid and settled UO 2 or on UO 2 pre-dispersed by forced trapping of sodium). To date, 6 tests have been performed. These tests have always resulted in fine fragmentation without any violent interaction. Since no knowledge is available on the change of grain size distribution with time, on the temperature of grain formation, and on the grain movement in the sodium, it is very difficult to interpret these UO 2 -Na tests. We intend to carry out more severe interaction tests on this experimental set-up, by eliminating as much as possible the non-condensable gas which cushions the mechanical impact of the sodium on the UO 2 (tests have shown that by strongly de-pressurizing the liquid UO 2 the fuel could be dispersed by boiling, and this effect should also improve the possibilities of a liquid/liquid contact). - by injecting a little sodium into the UO 2 to facilitate its dispersion in the coolant

A novel method of non-violent dissolution of sodium metal in a concentrated aqueous solution of Epsom salt

International Nuclear Information System (INIS)

Lakshmanan, A.R.; Prasad, M.V.R.; Ponraju, D.; Krishnan, H.

2004-01-01

A new technique of non-violent and fast dissolution of sodium metal in a concentrated aqueous solution of Epsom salt (MgSO 4 .7H 2 O) at room temperature (RT) has been developed. The dissolution process is mildly exothermic but could be carried out even in a glass beaker in air under swift stirring condition. The reaction products consist of mixed salts of MgSO 4 and Na 2 SO 4 as well as Mg(OH) 2 which are only mildly alkaline and hence are non-corrosive and non-hazardous unlike NaOH. A 50 mL solution having Epsom salt concentration of 2 M was found to give the optimal composition for disposal of 1 g of sodium. Supersaturated (>2.7 M), as well as dilute (<1.1 M) solutions, however, cause violent reactions and hence should be avoided. Repeated sodium dissolution in Epsom solution produced a solid waste of 4.7 g per g of sodium dissolved which is comparable with the waste (4 g) produced in 8 M NaOH solution. A 1.4 M Epsom solution sprayed with a high-pressure jet cleaner at RT in air easily removed the sodium blocked inside a metal pipe made of mild steel. The above jet also dissolved peacefully residual sodium collected on the metal tray after a sodium fire experiment. No sodium fire or explosion was observed during this campaign. The Epsom solution spray effectively neutralized the minor quantity of sodium aerosol produced during this campaign. This novel technique would hence be quite useful for draining sodium from fast breeder reactor components and bulk processing of sodium as well as for sodium fire fighting

Bioenergy from sisal residues

Energy Technology Data Exchange (ETDEWEB)

Jungersen, G. [Dansk Teknologisk Inst. (Denmark); Kivaisi, A.; Rubindamayugi, M. [Univ. of Dar es Salaam (Tanzania, United Republic of)

1998-05-01

The main objectives of this report are: To analyse the bioenergy potential of the Tanzanian agro-industries, with special emphasis on the Sisal industry, the largest producer of agro-industrial residues in Tanzania; and to upgrade the human capacity and research potential of the Applied Microbiology Unit at the University of Dar es Salaam, in order to ensure a scientific and technological support for future operation and implementation of biogas facilities and anaerobic water treatment systems. The experimental work on sisal residues contains the following issues: Optimal reactor set-up and performance; Pre-treatment methods for treatment of fibre fraction in order to increase the methane yield; Evaluation of the requirement for nutrient addition; Evaluation of the potential for bioethanol production from sisal bulbs. The processing of sisal leaves into dry fibres (decortication) has traditionally been done by the wet processing method, which consumes considerable quantities of water and produces large quantities of waste water. The Tanzania Sisal Authority (TSA) is now developing a dry decortication method, which consumes less water and produces a waste product with 12-15% TS, which is feasible for treatment in CSTR systems (Continously Stirred Tank Reactors). (EG)

Apparatus for removing impurities in the sodium of sodium cooled reactors

Energy Technology Data Exchange (ETDEWEB)