WorldWideScience

Sample records for residual radioactive contamination

  1. Residual radioactive contamination at Maralinga and Emu, 1985

    International Nuclear Information System (INIS)

    Lokan, K.H.

    1985-04-01

    An account is provided of residual contamination at Maralinga and Emu, in South Australia, where the United Kingdom Atomic Weapons Research Establishment conducted nuclear weapons development trials between 1953 and 1963. Detailed information is presented about contamination levels at sites on the range where radioactive materials were dispersed. Some of these were associated with trials involving natural uranium or short-lived isotopes which are no longer present. There are four sites where plutonium-239 was dispersed in substantial quantities from minor trials and information is presented about its distribution. Much of this material has been diluted by mixing with local soil, but there is a significant quantity of material present in the form of contaminated fragments, particularly at Taranaki. A considerable quantity of uranium-235 is also present at Taranaki. An assessment is made of the radiological significance of the dispersed plutonium and it is concluded that the material represents a potential long term hazard while it remains in its present form. Residual radioactivity associated with all but one of the seven major trial sites involving nuclear explosions continues to decay in a predictable way and will in the worst case, fall below levels considered safe for continuous occupancy within about fifty years. One site, Tadje, contains significant concentrations of plutonium over a small area and onsidered to be an additional plutonium-contaminated locality. Measurements of beryllium concentrations in soil are presented

  2. Residual radioactive contamination from decommissioning: Technical basis for translating contamination levels to annual dose

    International Nuclear Information System (INIS)

    Kennedy, W.E. Jr.; Peloquin, R.A.

    1990-01-01

    This document describes the generic modeling of the total effective dose equivalent (TEDE) to an individual in a population from a unit concentration of residual radioactive contamination. Radioactive contamination inside buildings and soil contamination are considered. Unit concentration TEDE factors by radionuclide, exposure pathway, and exposure scenario are calculated. Reference radiation exposure scenarios are used to derive unit concentration TEDE factors for about 200 individual radionuclides and parent-daughter mixtures. For buildings, these unit concentration factors list the annual TEDE for volume and surface contamination situations. For soil, annual TEDE factors are presented for unit concentrations of radionuclides in soil during residential use of contaminated land and the TEDE per unit total inventory for potential use of drinking water from a ground-water source. Because of the generic treatment of potentially complex ground-water systems, the annual TEDE factors for drinking water for a given inventory may only indicate when additional site data or modeling sophistication are warranted. Descriptions are provided of the models, exposure pathways, exposure scenarios, parameter values, and assumptions used. An analysis of the potential annual TEDE resulting from reference mixtures of residual radionuclides is provided to demonstrate application of the TEDE factors. 62 refs., 5 figs., 66 tabs

  3. Methodology for determining acceptable residual radioactive contamination levels at decommissioned nuclear facilities/sites

    International Nuclear Information System (INIS)

    Watson, E.C.; Kennedy, W.E. Jr.; Hoenes, G.R.; Waite, D.A.

    1979-01-01

    The ultimate disposition of decommissioned nuclear facilities and their surrrounding sites depends upon the degree and type of residual contamination. Examination of existing guidelines and regulations has led to the conclusion that there is a need for a general method to derive residual radioactive contamination levels that are acceptable for public use of any decommissioned nuclear facility or site. This paper describes a methodology for determining acceptable residual radioactive contamination levels based on the concept of limiting the annual dose to members of the public. It is not the purpose of this paper to recommend or even propose dose limits for the exposure of the public to residual radioactive contamination left at decommissioned nuclear facilities or sites. Unrestricted release of facilities and/or land is based on the premise that the potential annual dose to any member of the public using this property from all possible exposure pathways will not exceed appropriate limits as may be defined by Federal regulatory agencies. For decommissioned land areas, consideration should be given to people living directly on previously contaminated areas, growing crops, grazing food animals and using well water. Mixtures of radionuclides in the residual contamination representative of fuel reprocessing plants, light water reactors and their respective sites are presented. These mixtures are then used to demonstrate the methodology. Example acceptable residual radioactive contamination levels, based on an assumed maximum annual dose of one millirem, are calculated for several selected times following shutdown of a facility. It is concluded that the methodology presented in this paper results in defensible acceptable residual contamination levels that are directly relatable to risk assessment with the proviso that an acceptable limit to the maximum annual dose will be established. (author)

  4. Measurement of residual radioactive surface contamination by 2-D laser heated TLD

    International Nuclear Information System (INIS)

    Jones, S.C.

    1997-06-01

    The feasibility of applying and adapting a two-dimensional laser heated thermoluminescence dosimetry system to the problem of surveying for radioactive surface contamination was studied. The system consists of a CO 2 laser-based reader and monolithic arrays of thin dosimeter elements. The arrays consist of 10,201 thermoluminescent phosphor elements of 40 micron thickness, covering a 900 cm 2 area. Array substrates are 125 micron thick polyimide sheets, enabling them to easily conform to regular surface shapes, especially for survey of surfaces that are inaccessible for standard survey instruments. The passive, integrating radiation detectors are sensitive to alpha and beta radiation at contamination levels below release guideline limits. Required contact times with potentially contaminated surfaces are under one hour to achieve detection of transuranic alpha emission at 100 dpm/100 cm 2 . Positional information obtained from array evaluation is useful for locating contamination zones. Unique capabilities of this system for survey of sites, facilities and material include measurement inside pipes and other geometrical configurations that prevent standard surveys, and below-surface measurement of alpha and beta emitters in contaminated soils. These applications imply a reduction of material that must be classified as radioactive waste by virtue of its possibility of contamination, and cost savings in soil sampling at contaminated sites

  5. Residual radioactive contamination of the Maralinga range from nuclear weapons tests conducted in 1956 and 1957

    International Nuclear Information System (INIS)

    Cooper, M.B.; Duggleby, J.C.; Kotler, L.H.; Wise, K.N.

    1978-12-01

    Detailed geographical distributions and concentrations of long-lived radionuclides remaining from the major trials of nuclear weapons conducted at Maralinga in 1956 and 1957 are presented. It is shown that residual contamination due to fission products - mainly strontium-90, caesium-137 and europium-155 - are well below levels that could constitute a health hazard to occupants of the area. In the regions near the ground zeroes however, long-lived neutron activation products in soil - mainly cobalt-60 and europium-152 - are present in sufficient abundance to give rise to gamma-radiation dose-rates up to 2 milliroentgen per hour, which exceed maximum recommended dose-rates for continuous occupancy

  6. Radiation protection of radioactively contaminated large areas by phytoremediation and subsequent utilization of the contaminated plant residues (PHYTOREST)

    International Nuclear Information System (INIS)

    Mirgorodsky, Daniel; Ollivier, Delphine; Merten, Dirk; Bergmann, Hans; Buechel, Georg; Willscher, Sabine; Wittig, Juliane; Jablonski, Lukasz; Werner, Peter

    2010-01-01

    Much progress has been achieved over the past 20 years in remediating sites contaminated by heavy metal. However, very large contaminated areas have presented major problems to this day because of remediation costs. Phytoremediation is a new, emerging, sustainable technique of remediating areas with low heavy-metal contamination. One advantage of phytoremediation is the comparatively low cost of the process, which may make it usable also on large areas with low levels of contamination. Besides extracting and immobilizing metals, respectively, phytoremediation among other things also contributes to improving soil quality in terms of physics, chemistry, and ecology. Consequently, phytoremediation offers a great potential for the future. Research into phytoremediation of an area contaminated by heavy metals and radionuclides is carried out on a site in a former uranium mining district in Eastern Thuringia jointly by the Friedrich Schiller University, Jena, and the Technical University of Dresden in a project funded by the German Federal Ministry for Education and Research. The project serves to promote the introduction of soft, biocompatible methods of long-term remediation and to develop conceptual solutions to the subsequent utilization of contaminated plant residues. Optimizing area management is in the focus of phytoremediation studies. (orig.)

  7. JUSTIFICATION FOR THE RADIOLOGICAL CRITERIA FOR THE USE OF AREAS WITH RESIDUAL RADIOACTIVE CONTAMINATION BASED ON THE DOSE APPROACH

    Directory of Open Access Journals (Sweden)

    V. Yu. Golikov

    2017-01-01

    Full Text Available The article presents a methodology for assessing the radiological criteria for the use of the territory (a land plot with buildings with residual radioactive contamination from the so-called “green area”, i.e., complete release from radiation control until a number of restrictions are imposed on the use of the territory. In accordance with the further use of the territory, a range of scenarios and pathways for the exposure of the population was considered. A set of models and their parameters, corresponding to the number of the considered pathways of exposure, was defined. Assuming a uniform distribution of a radionuclide with a unit concentration in the source zone, the distribution of effective doses for the population living in the territory with the residual radioactive contamination for different irradiation scenarios was calculated by stochastic modeling, 95% of the quantile of which was attributed to the dose in the representatives of the critical population group. Next, the value of radiological criteria, depending on the implemented scenario, was determined as the ratio of the dose constraint EL = 0,3 mSv/yr and 95% quantile in the distribution of the effective dose from a unit contamination. The numerical values of radiological criteria for the presence of radionuclides in the soil are presented, both for the radiation scenarios that correspond to the permanent residence of the population in the contaminated territory and for recreational use. A further consideration is given to the so-called worker scenario, which corresponds to the limited time spent on the contaminated territory and the simultaneous effects of radionuclides contained both in the soil and in the construction of the buildings. A comparison of the results of the own calculations with the data of other authors was carried out.

  8. Dry decontamination technology development for high radioactive contaminant application - Development of residual radiation assessment methodology for high radioactive facility decontamination

    Energy Technology Data Exchange (ETDEWEB)

    Lee, G. J.; Hong, D. S.; Jeong, H. Y. [Korea Advanced Institute of Science and Technology, Taejon (Korea)

    2000-04-01

    Humidity around the concrete structure can make the moisture distribution within the concrete. Moisture content of the structure will change due to the diffusion process with time. Radioactive material on the surface of concrete will eventually diffuse into the porous concrete and contaminates the internal region of the concrete. In this study, we have assumed two different diffusion processes depending on the different moisture content. One is for slow diffusion process near the surface and the other is for fast diffusion process in deep region. We have developed the mathematical diffusion model for the two different diffusion regions and the corresponding analytic solutions for the two regions are obtained. 19 refs., 15 figs., 9 tabs. (Author)

  9. Radioactive surface contamination monitors

    International Nuclear Information System (INIS)

    Aoyama, Kei; Minagoshi, Atsushi; Hasegawa, Toru

    1994-01-01

    To reduce radiation exposure and prevent contamination from spreading, each nuclear power plant has established a radiation controlled area. People and articles out of the controlled area are checked for the surface contamination of radioactive materials with surface contamination monitors. Fuji Electric has repeatedly improved these monitors on the basis of user's needs. This paper outlines typical of a surface contamination monitor, a personal surface contamination monitor, an article surface contamination monitor and a laundry monitor, and the whole-body counter of an internal contamination monitor. (author)

  10. Residual radioactivity of treated green diamonds.

    Science.gov (United States)

    Cassette, Philippe; Notari, Franck; Lépy, Marie-Christine; Caplan, Candice; Pierre, Sylvie; Hainschwang, Thomas; Fritsch, Emmanuel

    2017-08-01

    Treated green diamonds can show residual radioactivity, generally due to immersion in radium salts. We report various activity measurements on two radioactive diamonds. The activity was characterized by alpha and gamma ray spectrometry, and the radon emanation was measured by alpha counting of a frozen source. Even when no residual radium contamination can be identified, measurable alpha and high-energy beta emissions could be detected. The potential health impact of radioactive diamonds and their status with regard to the regulatory policy for radioactive products are discussed. Copyright © 2017. Published by Elsevier Ltd.

  11. Residual radioactive contamination of the test site at Emu from nuclear weapons tests conducted in 1953

    International Nuclear Information System (INIS)

    Maclagan, D.S.; Cooper, M.B.; Duggleby, J.C.

    1979-08-01

    The detailed distributions and soil concentrations of long-lived radionuclides remaining from nuclear weapons trials conducted at Emu in October 1953, are presented. Significant radiation levels due to long-lived neutron activation products in soil, 60 Co and 152 Eu, occur only in the immediate vicinity of the ground zeros of TOTEM 1 and TOTEM 2. It is shown that the levels of contamination due to fallout products in the soil are well below those which would constitute a health hazard to occupants of the area

  12. Internal radioactive contamination treatment

    International Nuclear Information System (INIS)

    Tobajas, L. M.

    1998-01-01

    In a radiological emergency, the internal radioactive contamination becomes a therapeutic urgency and must be established as fast as possible. Just when a radioactive contamination accident occurs, it is difficult to know exactly the amount of radioactive materials absorbed and to estimate the dose received.. The decision to be taken after the incorporation of the radioactive material depends on the method and on the Radiological Protection Department collaboration. Any treatment achieving a reduction of the doses received or expected will be useful. The International Radiological Protection Commission doesn't recommend the use of the dose limit, to decide about the intervention necessity. However the LIA can be used as the reference point to establish the necessity and reach of the treatment. The object of the present work, is to introduce the general principles to carry out the internal people decontamination, under the last international recommendations. (Author) 4 refs

  13. Safety against radioactive contamination

    International Nuclear Information System (INIS)

    Anon.

    1983-01-01

    The ALWIT anticontamination suit is briefly described, consisting of lasting antistatic ''NDMEX III''. It was specially developed for the fire brigade who are exposed to a particular kind of contamination while carrying out radiation measurements during fire fighting, rescue and clearing up work. The ALWIT suit reliably prevents radioactive contamination of the surface of the body while wearing a breathing apparatus, independent of the ambient air. Tightly fitting cuffs on the neck, arms and legs together with zippers placed behind prevent contamination even with extreme movement. (P.F.K.)

  14. Natural radioactivity in petroleum residues

    International Nuclear Information System (INIS)

    Gazineu, M.H.P.; Gazineu, M.H.P.; Hazin, C.A.; Hazin, C.A.

    2006-01-01

    The oil extraction and production industry generates several types of solid and liquid wastes. Scales, sludge and water are typical residues that can be found in such facilities and that can be contaminated with Naturally Occurring Radioactive Material (N.O.R.M.). As a result of oil processing, the natural radionuclides can be concentrated in such residues, forming the so called Technologically Enhanced Naturally Occurring Radioactive Material, or T.E.N.O.R.M.. Most of the radionuclides that appear in oil and gas streams belong to the 238 U and 232 Th natural series, besides 40 K. The present work was developed to determine the radionuclide content of scales and sludge generated during oil extraction and production operations. Emphasis was given to the quantification of 226 Ra, 228 Ra and 40 K since these radionuclides,are responsible for most of the external exposure in such facilities. Samples were taken from the P.E.T.R.O.B.R.A.S. unity in the State of Sergipe, in Northeastern Brazil. They were collected directly from the inner surface of water pipes and storage tanks, or from barrels stored in the waste storage area of the E and P unit. The activity concentrations for 226 Ra, 228 Ra and 40 K were determined by using an HP Ge gamma spectrometric system. The results showed concentrations ranging from 42.7 to 2,110.0 kBq/kg for 226 Ra, 40.5 to 1,550.0 kBq/kg for 228 Ra, and 20.6 to 186.6 kBq/kg for 40 K. The results highlight the importance of determining the activity concentration of those radionuclides in oil residues before deciding whether they should be stored or discarded to the environment. (authors)

  15. Microfiltration of radioactive contaminants

    Energy Technology Data Exchange (ETDEWEB)

    Buckley, L P; Slade, J A; Vijayan, S; Wong, C F

    1993-04-01

    Cross-flow microfiltration processing of radioactive liquids has been in use at Chalk River Laboratories for about four years. The separation process removes suspended particles from radioactive waste solutions. The clean liquid can then be treated with conventional reverse osmosis membranes to achieve volume reduction factors approaching 100. Microfiltration removes particles below the rating of 0.2 microns, in part from particle agglomeration. Operating experience relating to a 15 USGPM unit is presented. Coupling microfiltration technology with chemical treatment enhances the removal of soluble species. Research and development experience with the removal of soluble contaminants found in ground water and waste water will be discussed. The technology has advantages over other membrane technologies, namely lower energy costs, a lesser degree of fouling, and a higher recovery of processed solution. Future applications of the technology are addressed. (author). 10 refs., 3 tabs., 4 figs.

  16. Microfiltration of radioactive contaminants

    International Nuclear Information System (INIS)

    Buckley, L.P.; Slade, J.A.; Vijayan, S.; Wong, C.F.

    1993-04-01

    Cross-flow microfiltration processing of radioactive liquids has been in use at Chalk River Laboratories for about four years. The separation process removes suspended particles from radioactive waste solutions. The clean liquid can then be treated with conventional reverse osmosis membranes to achieve volume reduction factors approaching 100. Microfiltration removes particles below the rating of 0.2 microns, in part from particle agglomeration. Operating experience relating to a 15 USGPM unit is presented. Coupling microfiltration technology with chemical treatment enhances the removal of soluble species. Research and development experience with the removal of soluble contaminants found in ground water and waste water will be discussed. The technology has advantages over other membrane technologies, namely lower energy costs, a lesser degree of fouling, and a higher recovery of processed solution. Future applications of the technology are addressed. (author). 10 refs., 3 tabs., 4 figs

  17. Environmental radioactive contamination

    International Nuclear Information System (INIS)

    Saucedo, Edgardo

    2000-01-01

    The environmental radioactive contamination with the scientific and technological advances can produce big benefits or damages to the human beings or the environment. The approval of national or international laws in the population's education so that it can face the topic critically and the scientific formation of human resources and ethically for application of the ionizing radiations, they are the best road to take advantage to the maximum of benefits of these radiations, reducing to the minimum the risks on the man and the environment

  18. Electrolyze radioactive contamination away

    International Nuclear Information System (INIS)

    Wedman, D.E.; Martinez, H.E.; Nelson, T.O.

    1996-01-01

    The Los Alamos National Laboratory Plutonium Facility is using electrolysis to clean the surfaces of hazardous materials. In the past, contaminated metals were cleaned with concentrated acids. Although these treatments make the surfaces safer, they produce other radioactive and toxic wastes in turn. Anodic current passes through a piece of stainless steel submersed in a sodium nitrate solution, and steel dissolves at the surfaces. Surface contamination strips away along with the surface layers. The authors are using this electrolysis approach to remove plutonium and americium from stainless steel and uranium. Unlike acid washing processes, electrolytic decontamination can be accomplished quickly. Little waste is generated regardless of how much material has to be removed from the surface. Material removal is proportional to the applied current, which gives the operator control over the rate and extent of decontamination

  19. Decontaminating method for radioactive contaminant

    International Nuclear Information System (INIS)

    Suzuki, Ken-ichi.

    1994-01-01

    After decontamination of radioactive contaminates with d-limonene, a radioactive material separating agent not compatible with liquid wastes caused by decontamination is added to the liquid wastes. Then after stirring, they are stood still to be separated into two phases, and the radioactive materials in the liquid waste phase caused by decontamination are transferred to the phase of the radioactive material separating agent. With such procedures, they can satisfactorily be separated into two phases of d-limonene and the radioactive material separating agent. Further, d-limonene remaining after the separation can be used again as a decontaminating agent for radioactive contaminates. Therefore, the amount of d-limonene to be used can be reduced, to lower the cost for cleaning, thereby enabling to reduce the amount of radioactive wastes formed. (T.M.)

  20. Radioactive contamination in imported foods

    International Nuclear Information System (INIS)

    Kan, Kimiko; Maki, Toshio; Nagayama, Toshihiro; Hashimoto, Hideki; Kawai, Yuka; Kobayashi, Maki; Shioda, Hiroko; Nishima, Taichiro

    1990-01-01

    On April 26, 1986, explosion occurred in Chernobyl nuclear power station in USSR, and radioactivity contamination was brought about in almost all countries in the world. In European countries, crops were contaminated directly with radioactive fallout to high concentration. Also in Japan, after one week the radioactivity higher than usual was detected in environment, and also in vegetables, milk, tea leaves and others. Thereafter, in order to cope with the import of contaminated foods, inspection and watch system was strengthened by deciding the interim limit of radioactive concentration. However the cases of exceeding the interim limit were often reported. In order to remove the harmful foods due to radioactive contamination and to meet the fear of consumers, the authors measured the radioactive concentration in foods distributed in Tokyo and investigated the actual state of contamination. The samples were 920 imported foods. The experimental method, the preparation of samples, the method of analysis and the results are reported. The samples in which the radioactive concentration exceeding 50 Bq/kg was detected were 25 cases. The food having the high frequency of detection was flavors. (K.I.)

  1. Radiation doses from residual radioactivity

    International Nuclear Information System (INIS)

    Okajima, Shunzo; Fujita, Shoichiro; Harley, John H.

    1987-01-01

    In this chapter available data and calculations for assessing the exposure of survivors of the Hiroshima and Nagasaki bombs and persons who entered the cities after the bombings have been presented. It appears that it is possible to produce firm estimates only for external radiation and, while the internal contribution for long-lived fission products appears small, there is no way to evaluate potential exposures to the short-lived fission products. The radiation exposure in the most highly contaminated fallout area of a few hectares at Nishiyama, Nagasaki, is estimated as 20 to 40 R when integrated from one hour to infinity using a decay exponent of -1.2. For the Hiroshima Koi-Takasu area, the corresponding exposure is estimated as 1 to 3 R. The falloff with distance for Nagasaki is not steep and an exposure of one-fifth of the maximum is spread over an area of perhaps 1000 ha. With the assumption stated above, the potential maximum exposures to external radiation from induced radioactivity at the hypocenter is estimated to be about 80 R fir Hiroshima and 30 to 40 R for Nagasaki with the assumptions stated above. These exposures fall off with both time and distance. The cumulative exposure would be about one-third as large after a day and only a few percent after a week. The falloff with distance is less striking, but can be estimated from the areas listed or from the curves shown in Gritzner and Woolson. Unlike the fallout, which exposed individuals in their living areas, exposures to induced activity came from reentry of individuals into the area around the hypocenter. As an example, an individual entering the Hiroshima hypocenter area after one day and working 10 or 20 hours a day for a week would have been exposed to about 10 R. If the person had been working at a distance of 500 m, the exposure would have been about 1 R and, at 1000 m, about 20 mR. The exposure described apply to the specified areas in the two cities. Application of these values to individuals

  2. Studies by nuclear and physico-chemical methods of tissue's metallic contamination located around biomaterials. Toxicity measurements of several biomaterials residual radioactivity

    International Nuclear Information System (INIS)

    Guibert, Geoffroy

    2004-01-01

    Implants used as biomaterials fulfill conditions of functionality, compatibility and occasionally bio-activity. There are four main families of biomaterials: metals and metal alloys, polymers, bio-ceramics and natural materials. Because of corrosion and friction in the human body, implants generate debris. These debris develop different problems: toxicity, inflammatory reactions, prosthetic unsealing by osseous dissolution. Nature, size, morphology and amount of debris are the parameters which have an influence on tissue response. We characterize metallic contamination coming from knee prosthesis into surrounding capsular tissue by depth migration, in vivo behaviours, content, size and nature of debris. The PIXE-RBS and STEM-EDXS methods, that we used, are complementary, especially about characterization scale. Debris contamination distributed in the whole articulation is very heterogeneous. Debris migrate on several thousands μm in tissue. Solid metallic particles, μm, are found in the most polluted samples, for both kinds of alloys TA6V and CrCoMo. In the mean volume analysed by PIXE, the in vivo mass ratios [Ti]/[V] and [Co]/[Cr] confirm the chemical stability of TA6V debris and chemical evolution of CrCoMo debris. Complementary measures of TA6V grains, on a nano-metric scale by STEM-EDXS, show a dissolution of coarse grain (μm) in smaller grains (nm). Locally, TA6V grains of a phase are detected and could indicate a preferential dissolution of β phase (grain boundaries) with dropping of Al and V, both toxic and carcinogenic elements. A thin target protocol development correlates PIXE and histological analysis on the same zone. This protocol allows to locate other pathologies in relationship with weaker metal contamination, μg/g, thanks to the great sensitivity of PIXE method. Harmlessness with respect to the residual radioactivity of several natural or synthetic biomaterials is established, using ultra low background noise γ detection system. (author)

  3. Radioactive contamination of environment

    International Nuclear Information System (INIS)

    Chytil, I.

    1981-01-01

    A computer model is discussed describing radioactivity transport between the source and the organism. The model is to be applied in assessing the effect of a nuclear installation on the organism. Fortran and Pascal appear to be the most appropriate computer languages. With respect to internal memory requirements, the program file is estimated to consist of a control program and a number of subprograms. Upon setting the radioactivity transport and the output requirements the control program should recall the necessary subprograms. The program file should allow the complete data file and the solutions of all possible radioactivity transport variants to be inputted. It is envisaged that several subprograms will be available for one type of radioactivity transport, this depending on different accuracy of the transport description. Thus, the requirements for input data will also differ. (Z.M.)

  4. Foodstuffs (radioactive contamination)

    International Nuclear Information System (INIS)

    Thompson, Donald; Taylor, Teddy; Campbell-Savours, D.N.

    1987-01-01

    The proceedings are given of the debate in the UK House of Commons on the maximum permitted radioactivity levels for foodstuffs, feeding stuffs and drinking water in the case of abnormal levels of radioactivity or of a nuclear accident. The motion takes note of European Community Document no. 7183/87 and urges the Community to assure a common standard of health protection by adopting a rational set of scientifically based intervention levels for foodstuffs. (UK)

  5. Radioactive contamination of recycled metals

    International Nuclear Information System (INIS)

    Lubenau, J.O.; Cool, D.A.; Yusko, J.G.

    1996-01-01

    Radioactive sources commingled with metal scrap have become a major problem for the metals recycling industry worldwide. Worldwide there have been 38 confirmed reports of radioactive sources accidentally smelted with recycled metal. In some instances, contaminated metal products were subsequently distributed. The metal mills, their products and byproducts from the metal making process such as slags, crosses and dusts from furnaces can become contaminated. In the U.S., imported ferrous metal products such as reinforcement bars, pipe flanges, table legs and fencing components have been found contaminated with taco. U.S. steel mills have unintentionally smelted radioactive sources on 16 occasions. The resulting cost for decontamination waste disposal and temporary closure of the steel mill is typically USD 10,000,000 and has been as much as USD 23,000,000. Other metal recycling industries that have been affected by this problem include aluminum, copper, zinc, gold, lead and vanadium. (author)

  6. 49 CFR 175.705 - Radioactive contamination.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Radioactive contamination. 175.705 Section 175.705... Regulations Applicable According to Classification of Material § 175.705 Radioactive contamination. (a) A... (radioactive) materials that may have been released from their packagings. (b) When contamination is present or...

  7. Radioactive contamination of sewage sludge

    International Nuclear Information System (INIS)

    Soeder, C.J.; Zanders, E.; Raphael, T.

    1986-01-01

    Because of the radioactivity released through the explosion of the nuclear reactor near Chernobyl radionuclides have been accumulated to a significant extent in sewage sludge in the Federal Republic of Germany. This is demonstrated for samples from four activated sludge plants according to a recent recommendation of the German Commission for Radiation Protection, there is until now no reason to deviate from the common practices of sludge disposal or incineration. The degree of radioactive contamination of plant materials produced on farm lands on which sewage sludge is being spread cannot be estimated with sufficient certainty yet. Additional information is required. (orig.) [de

  8. RESRAD, Residual Radioactive Material Guideline Implementation

    International Nuclear Information System (INIS)

    1998-01-01

    This code system is designed to calculate site-specific residual radioactive material guidelines, and radiation dose and excess cancer risk to an on-site resident (maximally exposed individual). A guideline is a radionuclide concentration or level of radioactivity that is acceptable if a site is to be used without radiological restrictions. Guidelines are expressed as concentrations of residual radionuclides in soil. Soil is unconsolidated earth material, including rubble and debris that may be present. The guidelines are based on the following principles: (1) the total effective dose equivalent should not exceed 100 mrem/yr for all plausible land uses and 30 mrem/yr for current and likely future land uses and (2) doses should be kept as low as reasonably achievable (ALARA). Nine environmental pathways are considered: direct exposure, inhalation of dust and radon, and ingestion of plant foods, meat, milk, aquatic foods, soil, and water. CCC-0552/04: A - Description of program or function: RESRAD-BUILD Version 2.36 is a pathway analysis model designed to evaluate the potential radiological dose incurred by an individual who works or lives in a building contaminated with radioactive material. The radioactive material in the building structure can be released into the indoor air by mechanisms such as diffusion (radon gas), mechanical removal (decontamination activities), or erosion (removable surface contamination). In the June 1998 update, RESRAD was updated to Version 5.82 and RESRAD-BUILD was updated to version 2.36. The following notes highlight new features: RESRAD5.82 (4/30/98): - Allow plot data to be exported to tab-delimited text file - Corrected Installation problem to Windows 3.1 - Corrected plotting problem for soil guidelines RESRAD-BUILD2.36 (4/9/98): - Corrected problem with simultaneously changing number of wall regions and their parameters - Added OK button to uncertainty window - Made sure first uncertainty variable in added on first try See the

  9. Some bioindicators of radioactive contamination

    International Nuclear Information System (INIS)

    Cosma, C.; Cozmuta, I.; Micu, C.

    1996-01-01

    The lessons that could be learned from the Chernobyl accident were numerous and encompassed all areas. One of those lead to the discovery of new monitoring methods which also supply to cost-effective solutions to control contaminant radioactive discharges in the environment. Through the measurements performed, we discovered that some samples, because of their radioactive content restrained also for long periods of time, can be used as bioindicators. Hen eggs between May 1-30 1986 were analysed (identification of radionuclides with a Ge(Li) detector and measuring of total gamma activity with NaI(T1)). Various aspects pursued revealed that eggs are precious witness of vegetable food contamination with fission products, especially Ba-140 and I-131, behaving as radionuclide separators (Ba-140 in egg shell -301 Bq/egg and I-131 in the content - 182 Bq/egg). Some of the most important pharmaceutical plants from Transylvania measured during 1986-1994 period presents high cesium radioactivity. The perennial plants (as Lichen Islandicus) for the same period accumulated a greater activity that the annual ones. Especially the lichen, because of the their slow decreasing activity are suitable as biological detectors also in retrospective measurements. Measuring the activity of some pollen samples was rediscovered. The pollen grains, during their transport in air by the bees, are acting like a filter for radionuclides so that we could use they to monitor the deliverance of these substances in air. (author)

  10. Radioactive contamination of the Guatemalan marine environment

    International Nuclear Information System (INIS)

    Perez-Sabino, J.F.; Oliva de Sandoval, B.E.; Orozco-Chilel, R.M.; Aguilar-Sandoval, E.

    1999-01-01

    As part of the IAEA TC project GUA/2/005 'Radioactivity and Contamination of the Marine Environment in Guatemala', concentrations of artificial and natural radionuclides have been determined in marine water and sediments, giving important information to establish the base line of the natural radioactivity and the radioactive contamination in this area that not have been studying

  11. Radioactive contamination of the Guatemalan marine environment

    Energy Technology Data Exchange (ETDEWEB)

    Perez-Sabino, J F; Oliva de Sandoval, B E; Orozco-Chilel, R M; Aguilar-Sandoval, E [Universidad de San Carlos de Guatemala, Facultad de Ciencias Quimicas y Farmacia, Unidad de Analisis Instrumental, Guatemala C.A. (Guatemala)

    1999-07-01

    As part of the IAEA TC project GUA/2/005 `Radioactivity and Contamination of the Marine Environment in Guatemala`, concentrations of artificial and natural radionuclides have been determined in marine water and sediments, giving important information to establish the base line of the natural radioactivity and the radioactive contamination in this area that not have been studying 4 refs, 1 fig., 4 tabs

  12. Contamination due to radioactive materials

    International Nuclear Information System (INIS)

    Woodhead, D.S.

    1984-01-01

    The peaceful exploitation of radioactivity and the expansion of the nuclear power programme ensure that the disposal of radioactive wastes will cause contamination of the marine environment in the foreseeable future. The exposure of marine organisms to radioactivity from wastes has been studied in depth and related to exposure to natural background radiation. Concentrations of natural radionuclides and those from marine waste disposal have been measured at various stations in the oceans and seas around the world. The fate of radionuclides at four representative sites has been studied and the concentrations of radionuclides in oysters, porphyra, plaice in the Windscale discharge area have been measured. The extent of human exposure, particularly with reference to seafood consumption in local fishing communities, has been assessed. Effects of radiation on developing fish embryos and eggs and genetic radiation effects in aquatic organisms has been studied. The above studies reveal that the controls applied to the discharge of radioactive wastes to limit hazards to humans also provide adequate protection for populations of marine organisms. (U.K.)

  13. Radioactive food and environment contamination

    International Nuclear Information System (INIS)

    Yousif, A.M.

    2001-01-01

    The Food and Environment Control Centre of Abu Dhabi Municipality with the help of IAEA has established facilities for regular monitoring of food and environmental samples for radioactive contamination. The Centre is now capable of measuring gamma, beta as well as alpha activity in different types of samples. The main activities in the area of food monitoring are as follows: General monitoring of food gamma radionuclides in foodstuffs by high resolution gamma spectrometry; Determination of specific gamma radionuclides in foodstuffs by high resolution gamma spectrometry; Radiochemical determination of Sr-90 using liquid scintillation analyzer or by gas flow proportional counter; Measurement of gross alpha activity in drinking water

  14. Biological cycles of radioactive contaminants

    International Nuclear Information System (INIS)

    Michon, M.-G.

    1959-01-01

    Artificial radio-elements (synthesized for scientific or industrial purposes)having been released, may be absorbed by plants or animals, and may eventually involve a catenation of organisms as some feed on the others. All organisms living in a polluted river become more radioactive than the water, which was to be expected, in as much as organisms are hypertonic in respect to sweet water. Conversely, soil brings into play physico-chemical phenomena (absorption) such that plants can get only a small portion of contaminating radio-elements, land animal feeding on such plants are relatively less exposed to contamination, and carnivorous animals feeding on herbivorous are still less exposed. Man, notably is fairly well protected, whereas lower organisms, notably unicellular organisms may suffer (mutations..). Reprint of a paper published in 'Revue de Pathologie Generale et de Physiologie Clinique', n. 707, April 1959, p. 505-514 [fr

  15. Contamination of foods by radioactive rains

    Energy Technology Data Exchange (ETDEWEB)

    Obo, F; Wakamatsu, C; Nakae, Y; Higasayama, S

    1955-01-01

    The radioactivities of various vegetable foods contaminated by radioactive rains in May, 1954, in the Kagoshima Area were detected. Tea showed especially high radioactivities which could be extracted with hot water. Radioactive Nb, Zr, Hf, Ce, Y, Pr, and La were detected in the hot water extractions of tea by ion-exchange chromatography. The partial contribution of /sup 40/K in these radioactive vegetables was critically examined.

  16. Measurement of radioactivity in contaminated crops

    Energy Technology Data Exchange (ETDEWEB)

    Yamada, Y; Hasegawa, M; Kihara, T

    1956-01-01

    A method called the Direct Method was developed to correct for natural /sup 40/K radiation in plant samples. The K content of the ashed sample is determined by flamephotometry. The radioactivity in a 100 mg sample is measured and the natural radioactivity from /sup 40/K determined by calculation subtracted. Tea samples tested gave evidence of contamination by radioactive fallout.

  17. Radioactive material in residues of health services residues

    International Nuclear Information System (INIS)

    Costa R, A. Jr.; Recio, J.C.

    2006-01-01

    The work presents the operational actions developed by the one organ responsible regulator for the control of the material use radioactive in Brazil. Starting from the appearance of coming radioactive material of hospitals and clinical with services of nuclear medicine, material that that is picked up and transported in specific trucks for the gathering of residuals of hospital origin, and guided one it manufactures of treatment of residuals of services of health, where they suffer radiological monitoring before to guide them for final deposition in sanitary embankment, in the city of Sao Paulo, Brazil. The appearance of this radioactive material exposes a possible one violation of the norms that govern the procedures and practices in that sector in the country. (Author)

  18. Radioactive contamination at Chelyabinsk-65, Russia

    International Nuclear Information System (INIS)

    Cochran, T.B.; Norris, R.S.; Suokko, K.L.

    1993-01-01

    As a consequence of poor waste management practices at Chelyabinsk-65, primarily during the first two decades of operations, the site and its surroundings were extensively contaminated, and thousands of people were unknowingly exposed to excessive levels of radiation. In terms of human health consequences, most of the damage has already been inflicted. Nevertheless, containment of the residual radioactivity in high-level waste tanks, in the reservoirs along the Techa River, and in and below Lake Karachay represents expensive challenges for which the best, or even adequate solutions, have yet to be devised. Russian scientists have the knowledge to address these problems, but lack practical experience with contemporary waste management practices. Western expertise could be helpful in quantifying the extent of the problems and devising solutions. However, the real challenge will be to mobilize the economic resources for effective cleanup at Chelyabinsk-65 in light of all the other economic and environmental problems Russia faces. 81 refs

  19. Measures for radiation prevention and remediation of islightly radioactive contaminated sites by phytoremediation and subsequent utilization of the loaded plant residues (PHYTOREST). Final report

    International Nuclear Information System (INIS)

    Willscher, Sabine; Werner, Peter; Jablonski, Lukasz; Wittig, Juliane

    2013-01-01

    contaminated geosubstrates now can be carried out within the radiation protection regulations. Hence, the project provides a substantial contribution to the radiation protection of HM/R contaminated soils. Within the research project, ways for the utilization of HM/R- contaminated plant residuals were highlighted; this gives a substantial contribution for minimization of wastes, the winning of sustainable bioenergy and the recycling of materials. Here, different ways of solutions were investigated. The research project was carried out within the scientific funding program ''Closedown and decommissioning of nuclear facilities''. The results of the project will contribute to the development of a biologically benign, sustainable technique for the remediation of large contaminated areas that originate mostly from the legacy of the former U mining. As a general result of this comprehensive research project, a phytostabilization/ phytoextraction of such SM/R contaminated sites is feasible with a protection of ground water, and the plant crop from phytoremediation of the HM/R contaminated field site can be utilized for the winning of bioenergy (gaseous/ liquid products or thermal utilization). The beneficial combination of phytoremediation and subsequent utilization of the biomass can be further developed to an innovative and sustainable remediation technology with national and international application potential.

  20. Development of high-level radioactive waste treatment and conversion technologies 'Dry decontamination technology development for highly radioactive contaminants'

    International Nuclear Information System (INIS)

    Oh, Won Zin; Lee, K. W.; Won, H. J.; Jung, C. J.; Choi, W. K.; Kim, G. N.; Moon, J. K.

    2001-04-01

    The followings were studied through the project entitled 'Dry Decontamination Technology Development for Highly Radioactive Contaminants'. 1.Contaminant Characteristics Analysis of Domestic Nuclear Fuel Cycle Projects(NFCP) and Applicability Study of the Unit Dry-Decontamination Techniques A. Classification of contaminated equipments and characteristics analysis of contaminants B. Applicability study of the unit dry-decontamination techniques 2.Performance Evaluation of Unit Dry Decontamination Technique A. PFC decontamination technique B. CO2 decontamination technique C. Plasma decontamination technique 3.Development of Residual Radiation Assessment Methodology for High Radioactive Facility Decontamination A. Development of radioactive nuclide diffusion model on highly radioactive facility structure B. Obtainment of the procedure for assessment of residual radiation dose 4.Establishment of the Design Concept of Dry Decontamination Process Equipment Applicable to Highly Radioactive Contaminants 5.TRIGA soil unit decontamination technology development A. Development of soil washing and flushing technologies B. Development of electrokinetic soil decontamination technology

  1. Radioactive elements and earthworms in contaminated soils

    International Nuclear Information System (INIS)

    Suleymanova, A.S.; Abdullayev, A.S.; Ahmadov, G.S.; Naghiyev, J.A.; Samadov, P.A.

    2010-11-01

    Earthworms are one of the indispensable soil animals which treat soil with letting it through their gut and help increasing soil fertility. The effect of radioactive elements and comparative effect of heavy metals to the vital functions of earthworms were determined in laboratory conditions. Experiments were continued for a month, and first of all, each soil type, grey-brown soil from Ramana iodine plant territory of Baku city, brown soil from Aluminum plant territory of Ganja city, aborigine grey-brown soil of Absheron peninsula, treated with Ra and U salts as model variants and brown soil of Ganja city was analyzed by gamma-spectrometer for radionuclide determining at the beginning and at the end of the experiment. Earthworms (Nicodrilus Caliginosus Sav.trapezoides) aboriginal for Absheron peninsula and plant residues were added to the soil. At the end of the month the biomass, survival value, coprolite allocation value, food activity and catalase value in earthworms and in soil were determined. The gamma-spectrometric analysis results gave interesting values in coprolites, soils which had been treated through the earthworms' gut. In comparison with the initial variants in experimental results more percent of radioactivity was gathered in coprolites. By this way earthworms absorbed most of radioactive elements and allocated them as coprogenous substances on the upper layer of soil. During absorbing, some percents of radioactive elements were also gathered in gut cells of the earthworms. Thereby determination of some vital functions of earthworms was expedient. Thus, by the instrumentality of these experiments we can use earthworms for biodiagnosis and for bioremediation of contaminated soils with radionuclides and heavy metals.

  2. Process for reducing radioactive contamination in phosphogypsum

    International Nuclear Information System (INIS)

    Palmer, J.W.; Gaynor, J.C.

    1983-01-01

    In a process for reducing radioactive contamination of phosphogypsum, anhydrite crystals are obtained through dehydration of the phosphogypsum in strong sulfuric acid: a portion of the anhydrite crystals is converted to subtantially radiation free gypsum by crystallizing out on radiation free gypsum seed crystals. These coarse radiation free gypsum crystals are then separated from the small anhydrite crystal relics containing substantially all of the radioactive contamination

  3. Cleanup of radioactivity contamination in environment

    International Nuclear Information System (INIS)

    Kosako, Toshiso

    1994-01-01

    Environmental radioactivity cleanup is needed under a large scale accident in a reactor or in an RI irradiation facility which associates big disperse of radioactivities. Here, the fundamental concept including a radiation protection target, a period classification, planning, an information data base, etc. Then, the methods and measuring instruments on radioactivity contamination and the cleanup procedure are explained. Finally, the real site examples of accidental cleanup are presented for a future discussion. (author)

  4. Radiation protection of radioactively contaminated large areas by phytoremediation and subsequent utilization of the contaminated plant residues (PHYTOREST); Massnahmen zur Strahlenschutzvorsorge radioaktiv belasteter Grossflaechen durch Sanierung mittels Phytoremediation und anschliessende Verwertung der belasteten Pflanzenreststoffe (PHYTOREST)

    Energy Technology Data Exchange (ETDEWEB)

    Mirgorodsky, Daniel; Ollivier, Delphine; Merten, Dirk; Bergmann, Hans; Buechel, Georg [Jena Univ. (Germany). Inst. fuer Geowissenschaften; Willscher, Sabine; Wittig, Juliane; Jablonski, Lukasz; Werner, Peter [Technische Univ. Dresden, Pirna (Germany). Inst. fuer Abfallwirtschaft und Altlasten

    2010-12-15

    Much progress has been achieved over the past 20 years in remediating sites contaminated by heavy metal. However, very large contaminated areas have presented major problems to this day because of remediation costs. Phytoremediation is a new, emerging, sustainable technique of remediating areas with low heavy-metal contamination. One advantage of phytoremediation is the comparatively low cost of the process, which may make it usable also on large areas with low levels of contamination. Besides extracting and immobilizing metals, respectively, phytoremediation among other things also contributes to improving soil quality in terms of physics, chemistry, and ecology. Consequently, phytoremediation offers a great potential for the future. Research into phytoremediation of an area contaminated by heavy metals and radionuclides is carried out on a site in a former uranium mining district in Eastern Thuringia jointly by the Friedrich Schiller University, Jena, and the Technical University of Dresden in a project funded by the German Federal Ministry for Education and Research. The project serves to promote the introduction of soft, biocompatible methods of long-term remediation and to develop conceptual solutions to the subsequent utilization of contaminated plant residues. Optimizing area management is in the focus of phytoremediation studies. (orig.)

  5. Technologies for remediation of radioactively contaminated sites

    International Nuclear Information System (INIS)

    1999-06-01

    This report presents particulars on environmental restoration technologies (control and treatment) which can be applied to land based, radioactively contaminated sites. The media considered include soils, groundwater, surface water, sediments, air, and terrestrial and aquatic vegetation. The technologies addressed in this report can be categorized as follows: self-attenuation (natural restoration); in-situ treatment; removal of contamination; ex-situ treatment; and transportation and final disposal. The report provides also background information about and a general approach to remediation of radioactively contaminated sites as well as some guidance for the selection of a preferred remediation technology. Examples of remediation experience in Australia and Canada are given it annexes

  6. Technologies for remediation of radioactively contaminated sites

    Energy Technology Data Exchange (ETDEWEB)

    1999-06-01

    This report presents particulars on environmental restoration technologies (control and treatment) which can be applied to land based, radioactively contaminated sites. The media considered include soils, groundwater, surface water, sediments, air, and terrestrial and aquatic vegetation. The technologies addressed in this report can be categorized as follows: self-attenuation (natural restoration); in-situ treatment; removal of contamination; ex-situ treatment; and transportation and final disposal. The report provides also background information about and a general approach to remediation of radioactively contaminated sites as well as some guidance for the selection of a preferred remediation technology. Examples of remediation experience in Australia and Canada are given it annexes Refs, figs, tabs

  7. Radioactive contamination in imported foods (II)

    International Nuclear Information System (INIS)

    Kan, Kimiko; Maki, Toshio; Hashimoto, Hideki; Kawai, Yuka; Nagayama, Toshihiro; Kobayashi, Maki; Shioda, Hiroko; Nishima, Taichiro

    1991-01-01

    Five years have elapsed since the Chernobyl accident, but the effect of radioactivity contamination to foods has continued. Also in Japan, the imported foods which were ordered by the Ministry of Health and Welfare to be sent back due to radioactivity contamination do not cease. In fiscal year 1990, three cases occurred: tea from Albania, mushrooms from Yugoslavia and spices from france. If those are not checked at quarantines, it is feared that such foods are distributed in Japan. Among the foods which were ordered to be sent back in the past, there were those from Brazil and Hong Kong where the effect of the Chernobyl accident is little, and the foods contaminated with radioactivity spread worldwide through import and export. Therefore, attention must be paid to the foods from the countries where radioactivity contamination is little. Also it is feared that Japanese foods may be contaminated by being cultivated with imported feed, soil and fertilizer, for which there is no regulation. In this report, the radioactivity contamination of imported foods in fiscal year 1990 is described, and the experimental method and the results are reported. (K.I.)

  8. Survey of radioactive contamination for foodstuffs

    International Nuclear Information System (INIS)

    Lee, Wan No; Lee, Chang Wu; Choi, Geun Sik; Cho, Yeong Hyeon; Kang, Mun Ja; Cheong, Geun Ho; Kim, Hui Ryeong; Park, Du Won; Park, Hyo Guk; Kwak, Ji Yeon

    2006-11-01

    After the Chernobyl nuclear accident in 1986, a lot of countries including EU, Japan, USA are to strengthen survey of radioactive contamination for foodstuffs. Our country has also surveyed radioactive contamination of the imported foodstuffs and started to check continuously the radioactivity contamination of the open market foodstuffs since 2003. In this year, imported foodstuffs(130 samples) and domestic foodstuffs(10 samples) are analyzed to investigate the radioactive contamination. Sampled foodstuffs items are collected from the open markets; one group is the imported foodstuffs and the other group is the domestic foodstuffs producted around nuclear facilities and northeast of Sokcho city concerning recent situations. Samples are usually bought from traditional markets, mart, department store or the Internet. After pretreatments such as drying, ashing, and homogenization, all samples were analyzed by gamma spectrometer system for survey and assessment of radioactive contamination. The 131 I radionuclide isn't detected among all foodstuffs(imported and domestic). The 137 Cs radionuclide among the regulation radionuclides( 137 Cs, 13 4 C s, 131 I) of food code is only detected at the imported foodstuffs but its level is far below the maximum permitted level. For the improvement of measurement confidence, the developed analysis method is tested by the participation of the national and international intercomparison. The developed method based on test results and international standard would be used at radioactive analysis as well as an education of relative workers. It could be applied as the basis data for amending the analysis method of food code. It is technically supported for radioactive analysis of commercial company and the government including KFDA. Finally these results would be used to solve an ambiguous anxiety of a people for radiation exposure by foodstuffs intake and help the KFDA to manage systematically the radioactive contamination and to give

  9. Applied exposure modeling for residual radioactivity and release criteria

    International Nuclear Information System (INIS)

    Lee, D.W.

    1989-01-01

    The protection of public health and the environment from the release of materials with residual radioactivity for recycle or disposal as wastes without radioactive contents of concern presents a formidable challenge. Existing regulatory criteria are based on technical judgment concerning detectability and simple modeling. Recently, exposure modeling methodologies have been developed to provide a more consistent level of health protection. Release criteria derived from the application of exposure modeling methodologies share the same basic elements of analysis but are developed to serve a variety of purposes. Models for the support of regulations for all applications rely on conservative interpretations of generalized conditions while models developed to show compliance incorporate specific conditions not likely to be duplicated at other sites. Research models represent yet another type of modeling which strives to simulate the actual behavior of released material. In spite of these differing purposes, exposure modeling permits the application of sound and reasoned principles of radiation protection to the release of materials with residual levels of radioactivity. Examples of the similarities and differences of these models are presented and an application to the disposal of materials with residual levels of uranium contamination is discussed. 5 refs., 2 tabs

  10. ASSESSMENT OF RADIOACTIVE AND NON-RADIOACTIVE CONTAMINANTS FOUND IN LOW LEVEL RADIOACTIVE WASTE STREAMS

    International Nuclear Information System (INIS)

    R.H. Little, P.R. Maul, J.S.S. Penfoldag

    2003-01-01

    This paper describes and presents the findings from two studies undertaken for the European Commission to assess the long-term impact upon the environment and human health of non-radioactive contaminants found in various low level radioactive waste streams. The initial study investigated the application of safety assessment approaches developed for radioactive contaminants to the assessment of nonradioactive contaminants in low level radioactive waste. It demonstrated how disposal limits could be derived for a range of non-radioactive contaminants and generic disposal facilities. The follow-up study used the same approach but undertook more detailed, disposal system specific calculations, assessing the impacts of both the non-radioactive and radioactive contaminants. The calculations undertaken indicated that it is prudent to consider non-radioactive, as well as radioactive contaminants, when assessing the impacts of low level radioactive waste disposal. For some waste streams with relatively low concentrations of radionuclides, the potential post-closure disposal impacts from non-radioactive contaminants can be comparable with the potential radiological impacts. For such waste streams there is therefore an added incentive to explore options for recycling the materials involved wherever possible

  11. Rehabilitation of radioactive contaminated forests

    International Nuclear Information System (INIS)

    Panfilov, A.V.; Uspenskaya, E.Ju.

    2002-01-01

    As a result of radiation accidents and nuclear-weapon tests at the territory of the former USSR a part of the Forest Fund of 23 subjects of the Russian Federation has been contaminated by radionuclides. The contaminated forests, which are included in a structure of more than 130 forest management units (leskhozes) and more then 330 local forest management units, as a rule, are located in highly inhabited regions with traditionally intensive forestry management and high level of forest resources use. To provide radiologically safe forest management in the contaminated areas, the Federal Forest Service has developed and validated a special system of countermeasures. Use of this system makes it possible to diminish significantly the dose to personnel, to exclude the use of forest products with contamination exceeding radiological standards and to provide protection of the forest as a biogeochemical barrier to radionuclide migration from contaminated areas to human habitat. (author)

  12. Residual radioactive material guidelines: Methodology and applications

    International Nuclear Information System (INIS)

    Yu, C.; Yuan, Y.C.; Zielen, A.J.; Wallo, A. III.

    1989-01-01

    A methodology to calculate residual radioactive material guidelines was developed for the US Department of Energy (DOE). This methodology is coded in a menu-driven computer program, RESRAD, which can be run on IBM or IBM-compatible microcomputers. Seven pathways of exposure are considered: external radiation, inhalation, and ingestion of plant foods, meat, milk, aquatic foods, and water. The RESRAD code has been applied to several DOE sites to calculate soil cleanup guidelines. This experience has shown that the computer code is easy to use and very user-friendly. 3 refs., 8 figs

  13. Radioactive contamination of honey and other bee-keeping products

    International Nuclear Information System (INIS)

    Frantsevich, L.I.; Komissar, A.D.; Levchenko, I.A.

    1990-01-01

    Great amount of dust is collected in propolis under emergency atmospheric fallouts. Specific coefficient of the product migration amounts to several m 2 per 1 kg. Propolis is a good biological indicator of radioactive fallouts. The propolis collection is inadmissible after radioactive fallouts. Cocoon residuals obtained during bees-wax separation contain many radionuclides and should be disposed in special places. Nuclides are absent in bees-wax. Nuclides accumulated absent in a bee organism migrate into honey and queen milk, the honey is contaminated mainly via biogenic path

  14. Technologies for remediating radioactively contaminated land

    International Nuclear Information System (INIS)

    Pearl, M.

    2000-01-01

    This paper gives an overview of technologies that can be used for the remediation of radioactively contaminated ground. There are a wide variety of techniques available -most have established track records for contaminated ground, though in general many are only just being adapted to use for radioactively contaminated ground. 1) Remediation techniques for radioactively contaminated ground involve either removal of the contamination and transfer to a controlled/contained facility such as the national LLW repository at Drigg, or 2) immobilization, solidification and stabilization of the contamination where the physical nature of the soil is changed, or an 'agent' is added to the soil, to reduce the migration of the contaminants, or 3) isolation and containment of the contaminated ground to reduce contaminant migration and control potential detrimental effects to human health. Where contamination has to be removed, ex situ and in situ techniques are available which minimize the waste requiring disposal to an LLW repository. These techniques include: 1) detector-based segregation 2) soil washing by particle separations 3) oil washing with chemical leaching agents 4) electro remediation 5) phyto remediation. Although many technologies are potentially applicable, their application to the remediation of a specific contaminated site is dependent on a number of factors and related to detailed site characterization studies, results from development trials and BPEO (best practicable environmental option) studies. Those factors considered of particular importance are: 1) the clean-up target 2) technical feasibility relative to the particular site, soil and contaminant characteristics, and time frame 3) site infrastructure arrangements and needs, the working life of the site and the duration of institutional care 4) long-term monitoring arrangements for slow remedial techniques or for immobilization and containment techniques 5) validation of the remediation 6) health and

  15. Contamination of fodder and radioactivity in turkeys

    International Nuclear Information System (INIS)

    Kossakowski, S.; Olszewska, K.

    1985-01-01

    Radioactivity was determined in mixed fodder (IB, IC, IE) and in turkeys which were given that feeding stuff. In animals (25 males and 25 females) fed with the above mixed fodder for 16-24 weeks radioactivity was assessed in internal organs and in their tissues. It was found that radioactivity ranged from 322.2 Bq/kg to 190.6 Bq/kg. In males the highest contamination was found in the spleen (average 0.108 Bq/g), in skeletal muscles (0.082 Bq/g), and in the liver (0.080 Bq/g), and the lowest in the skin (0.046 Bq per 1 g). The findings indicate that radioactivity of carcasses and internal organs in turkeys fed with contamined fodder was much lower than that in fodder. 6 refs., 1 tab. (author)

  16. Radioactive contamination mapping system detailed design report

    International Nuclear Information System (INIS)

    Bauer, R.G.; O'Callaghan, P.B.

    1996-08-01

    The Hanford Site's 100 Area production reactors released radioactively and chemically contaminated liquids into the soil column. The primary source of the contaminated liquids was reactor coolant and various waste waters released from planned liquid discharges, as well as pipelines, pipe junctions, and retention basins leaking into the disposal sites. Site remediation involves excavating the contaminated soils using conventional earthmoving techniques and equipment, treating as appropriate, transporting the soils, and disposing the soils at ERDF. To support remediation excavation, disposal, and documentation requirements, an automated radiological monitoring system was deemed necessary. The RCMS (Radioactive Contamination Mapping System) was designed to fulfill this need. This Detailed Design Report provides design information for the RCMS in accordance with Bechtel Hanford, Inc. Engineering Design Project Instructions

  17. Decontamination of radioactively contaminated surfaces

    International Nuclear Information System (INIS)

    1986-10-01

    By this standard objective conditions to evaluate and test the ease of decontamination of surfaces under laboratory conditions are to be laid down. Ease of decontamination in this context denotes the summed-up effect of two material properties: a) the capacity of the material for retaining radioactive substances at its surface; b) the ease with which these substances are given off again in the course of cleaning processes. (orig./HP) [de

  18. Inventory of sites used to develop residual radioactivity criteria

    International Nuclear Information System (INIS)

    Ronca-Battista, M.; Hardeman, J.C. Jr.

    1986-01-01

    The US Environmental Protection Agency (EPA), in conjunction with the National Conference of Radiation Control Program Directors (CRCPD), has compiled an inventory of never licensed or otherwise poorly documented sites that may be contaminated with radioactive materials. This effort is in support of the EPA's development of radiation protection criteria for residual radioactivity at decommissioned sites. The inventory will help to establish the range of circumstances for which criteria are needed, as well as the suitability of candidate criteria for actual situations. The information will also be used to develop model sites and facilities for analyzing technical and economic feasibility of residual radioactivity criteria and to assess costs and benefits of alternate criteria. Relevant information about each site, such as radionuclides, waste forms, and quantities present will be included in the inventory when such information is available. The CRCPD has requested that each State radiation control agency furnish the information for the inventory. The inventory supplements the relatively extensive documentation of sites regulated by Federal or State agencies with information on old or unlicensed sites, such as old waste storage sites or radium ore processing facilities

  19. Characterization on incineration residue of radioactive solid wastes

    International Nuclear Information System (INIS)

    Katoh, Kiyoshi; Hirayama, Katsuyoshi; Kato, Akira.

    1989-01-01

    Characterization was carried out on incineration residue discharged from the radioactive solid waste incineration unit (capacity, 100 kg/h) in use at the Tokai Research Establishment of Japan Atomic Energy Research Institute (JAERI) to obtain basic data for investigating solidification methods of the residue. The characterized residue was taken from furnace and a primary ceramic filter of the incineration unit which incinerates combustible solid wastes generated at JAERI and the outside organizations. Items of characterization involve a particle size distribution, misplaced materials content, ignition loss, chemical composition and radioactivity of nuclides in the ash. As the results, the size of ash sampled from the furnace distributed a wide range, with about 35∼60 % of ash smaller than 5 mm and about 10∼25 % of massive one larger than 30 mm (max. size: ∼130 mm). The ignition loss was 2∼3 %. The chemical compositions of the ash were mainly SiO 2 , Fe 2 O 3 , CaO and Al 2 O 3 . The specific activities of the ash were about 0.4∼4 x 10 3 Bq/g, and principal contaminants were 60 Co and 137 Cs. (author)

  20. Contaminant transport at a waste residue deposit

    DEFF Research Database (Denmark)

    Engesgaard, Peter Knudegaard; Traberg, Rikke

    1996-01-01

    Contaminant transport in an aquifer at an incinerator waste residue deposit in Denmark is simulated. A two-dimensional, geochemical transport code is developed for this purpose and tested by comparison to results from another code, The code is applied to a column experiment and to the field site...

  1. Establishing community trust at radioactively contaminated sites

    International Nuclear Information System (INIS)

    Simpson, E.

    1999-01-01

    Establishing community trust is an essential element in the successful remediation of a radioactively contaminated site. The US Environmental Protection Agency (EPA), Region 2 has been involved in the clean up of numerous radioactively contaminated Comprehensive Environmental Response, Compensation and Liability Act (CERCLA), Resource Conservation Recovery Act (RCRA), and Formerly Utilized Site Remedial Action Program (FUSRAP) sites in New Jersey and New York. Each site presented a unique challenge which centered around establishing and, often, re-establishing the trust of the surrounding community. Thanks to the United States government's history regarding the use of radioactive materials, people question whether governmental regulators could possibly have the public's best interests in mind when it comes to addressing radioactively contaminated sites. It has been our experience that EPA can use its position as guardian of the environment to help establish public confidence in remedial actions. The EPA can even use its position to lend credibility to remedial activities in situations where it is not directly responsible for the clean-up. Some ways that we have found to instill community confidence are: establishing radioanalytical cross-check programs using EPA's National Air and Radiation Environmental Laboratory to provide analytical quality assurance; and establishing an environmental radiation monitoring program for the contaminated site and surrounding community. (author)

  2. Radioactive contamination of oil produced from nuclear-broken shale

    International Nuclear Information System (INIS)

    Arnold, W.D.; Crouse, D.J.

    1970-01-01

    The results of small-scale exposure and retorting tests indicate that oil recovered from shale that has been broken with nuclear explosives will be contaminated with tritium. When oil shale was heated in sealed flasks with tritiated water vapor or with tritiated hydrogen, both the shale and the oil subsequently retorted from the shale contained tritium. There was much less contamination of the shale or oil, however, when the shale was exposed to tritiated methane and ethane. Contamination of shale and oil with tritium, as the result, of exposure to tritiated water, increased as the exposure temperature, exposure pressure, and the tritium concentration in the water were increased. This contamination also increased as the exposure time was increased up to 25 days, but not significantly thereafter. More than 90% of the tritium was removed from contaminated shale by treating the shale with moist air at elevated temperatures. Only small amounts of the tritium were removed from crude oil by contacting it with solid drying agents or with water. When tritium-contaminated shale oil was distilled, the tritium contents of the recovered fractions were found to be approximately equal. After being heated with a sample of underground test-shot debris, liquid shale oil became contaminated with radioactive fission products. Most of the radioactivity of the oil was due to finely dispersed solids rather than to dissolved radionuclides. Filtration of the oil removed a major fraction of the radioactive material. When the contaminated oil was distilled, more than 99% of the radionuclides remained in the pot residue. (author)

  3. Radioactive contamination of oil produced from nuclear-broken shale

    Energy Technology Data Exchange (ETDEWEB)

    Arnold, W D; Crouse, D J

    1970-05-15

    The results of small-scale exposure and retorting tests indicate that oil recovered from shale that has been broken with nuclear explosives will be contaminated with tritium. When oil shale was heated in sealed flasks with tritiated water vapor or with tritiated hydrogen, both the shale and the oil subsequently retorted from the shale contained tritium. There was much less contamination of the shale or oil, however, when the shale was exposed to tritiated methane and ethane. Contamination of shale and oil with tritium, as the result, of exposure to tritiated water, increased as the exposure temperature, exposure pressure, and the tritium concentration in the water were increased. This contamination also increased as the exposure time was increased up to 25 days, but not significantly thereafter. More than 90% of the tritium was removed from contaminated shale by treating the shale with moist air at elevated temperatures. Only small amounts of the tritium were removed from crude oil by contacting it with solid drying agents or with water. When tritium-contaminated shale oil was distilled, the tritium contents of the recovered fractions were found to be approximately equal. After being heated with a sample of underground test-shot debris, liquid shale oil became contaminated with radioactive fission products. Most of the radioactivity of the oil was due to finely dispersed solids rather than to dissolved radionuclides. Filtration of the oil removed a major fraction of the radioactive material. When the contaminated oil was distilled, more than 99% of the radionuclides remained in the pot residue. (author)

  4. Non-radioactive stand-in for radioactive contamination. I. Non-radioactive tests

    International Nuclear Information System (INIS)

    Rohe, M.J.; Rankin, W.N.; Postles, R.L.

    1985-01-01

    Candidate non-radioactive materials for use as a stand-in for radioactive contamination during application of a high-pressure, hot water decontamination were identified and evaluated. A stand-in for radioactive contamination is needed to evaluate the decontaminability of replacement canyon cranes at the manufacturers location where actual radioactive contamination cannot be used. This evaluation was conducted using high-pressure, hot-water at 420 psi, 190 0 F, and 20 gal/min through a 1/8-in.-diam nozzle, the decontamination technique preferred by SRP Separations Department for this application. A non-radioactive stand-in for radioactive contamination was desired that would be removed by direct blast stream contact but would remain intact on surfaces where direct contact does not occur. This memorandum describes identification of candidate non-radioactive stand-in materials and evaluation of these materials in screening tests and tests with high-pressure, hot-water blasting. The following non-radioactive materials were tested: carpenter's line chalk; typing correction fluid; dye penetrant developer; latex paint with attapulyite added; unaltered latex paint; gold enamel; layout fluid; and black enamel. Results show that blue layout fluid and gold enamel have similar adherence that is within the range expected for actual radioactive contamination. White latex paint has less adherence than expected for actual radioactive contamination. The film was removed at a rate of 2 . Black enamel has more adherence than expected from actual radioactive contamination. In these tests ASTM No. 2B surfaces were harder to clean than either ASTM No. 1 or electropolished surfaces which had similar cleaning properties. A 90 0 blast angle was more effective than a 45 0 blast angle. In these tests there was no discernible effect of blast distance between 1 and 3 ft

  5. Manual for implementing residual radioactivity guidelines

    International Nuclear Information System (INIS)

    Gilbert, T.L.; Eckerman, K.F.; Hansen, W.R.; Healy, J.W.; Kennedy, W.E.; Napier, B.A.; Solday, J.K.

    1986-01-01

    The US Department of Energy (DOE) has recently issued guidelines for residual radioactivity at Formerly Utilized Sites Remedial Action Program (FUSRAP) and remote Surplus Facilities Management Program (SFMP) sites. A manual for implementing these guidelines has been prepared jointly by four DOE laboratories (ANL, LANL, ORNL, and PNL) and is being issued as a supplement to the guidelines. The manual presents procedures and tables for deriving site-specific guidelines for levels of residual radionuclide concentrations in soil that must not be exceeded if a site is to be released for unrestricted use. Guidance for implementing DOE ALARA policy for remedial actions is also included. The concentration factor method is used in the pathway analysis for deriving soil guidelines. The analysis has been structured in a manner that explicitly identifies all of the factors involved. Tables are provided for dose-conversion factors and pathway factors from which environmental transport factors for each radionuclide and pathway may be calculated. The scenarios used for deriving the environmental transport factors and dose conversion factors, and the manner in which the information provided in the manual is used to derive site-specific soil guidelines will be presented

  6. Decontamination method for radioactively contaminated material

    International Nuclear Information System (INIS)

    Shoji, Yuichi; Mizuguchi, Hiroshi; Sakai, Hitoshi; Komatsubara, Masaru

    1998-01-01

    Radioactively contaminated materials having surfaces contaminated by radioactive materials are dissolved in molten salts by the effect of chlorine gas. The molten salts are brought into contact with a low melting point metal to reduce only radioactive materials by substitution reaction and recover them into the low melting point metal. Then, a low melting point metal phase and a molten salt phase are separated. The low melting point metal phase is evaporated to separate the radioactive materials from molten metals. On the other hand, other metal ions dissolved in the molten salts are reduced into metals by electrolysis at an anode and separated from the molten salts and served for regeneration. The low melting point metals are reutilized together with contaminated lead, after subjected to decontamination, generated from facilities such as nuclear power plant or lead for disposal. Since almost all materials including the molten salts and the molten metals can be enclosed, the amount of wastes can be reduced. In addition, radiation exposure of operators who handle them can be reduced. (T.M.)

  7. Development of radioactive surface contamination monitor

    International Nuclear Information System (INIS)

    Hashimoto, Tadao; Hasegawa, Toru; Fukumoto, Keisuke; Ooki, Yasushi

    2008-01-01

    In the radiation facilities such as nuclear power plants, surface contamination of the people accessing or articles conveyed in and out of the radiation controlled areas is detected and monitored by installing contamination monitors at the boundary of controlled areas and uncontrolled areas against the expansion of the radioactive materials to out of the facilities. It is required for the surface contamination of articles to be tightened of control criteria as 'Guidelines for discrimination ways of nonradioactive waste (not classified as radioactive waste) generated from nuclear power plants' (hereinafter referred to as 'the Guideline') was established by the Nuclear and Industrial Safety Agency of the Ministry of Economy, Trade and Industry in August, 2005. It predicts that the control criteria of monitors other than article monitors are also tightened in the future. Fuji electric has been fabricating and delivering surface contamination detecting monitors. Now we are developing the new contamination monitor corresponding to the tightening of the control criteria. 'Large article transfer monitor', 'Clothing monitor' and 'Body surface contamination monitor' are introduced in this article. (author)

  8. Method for electrolytic decontamination of radioactive contaminated metals

    International Nuclear Information System (INIS)

    Tanaka, Akio; Horita, Masami; Onuma, Tsutomu; Kato, Koji

    1991-01-01

    The invention relates to an electrolytic decontamination method for radioactive contaminated metals. The contaminated sections are eluted by electrolysis after the surface of a piece of equipment used with radioactive substances has been immersed in an electrolyte. Metal contaminated by radioactive substances acts as the anode

  9. Radioactive contamination of sewage sludge. Preliminary data

    Energy Technology Data Exchange (ETDEWEB)

    Soeder, C J; Zanders, E; Raphael, T

    1986-01-01

    Because of the radioactivity released through the explosion of the nuclear reactor near Chernobyl radionuclides have been accumulated to a significant extent in sewage sludge in the Federal Republic of Germany. This is demonstrated for samples from four activated sludge plants according to a recent recommendation of the German Commission for Radiation Protection, there is until now no reason to deviate from the common practices of sludge disposal or incineration. The degree of radioactive contamination of plant materials produced on farm lands on which sewage sludge is being spread cannot be estimated with sufficient certainty yet. Additional information is required.

  10. Radioactive contamination in monitors received for calibration

    International Nuclear Information System (INIS)

    Dias, Paulo S.; Santos, Gilvan C. dos; Brunelo, Maria Antonieta G.; Paula, Tiago C. de; Pires, Marina A.; Borges, Jose C.

    2013-01-01

    The Calibration Laboratory - LABCAL, from the Research Center for Metrology and Testing - METROBRAS, MRA Comercio de Instrumentos Eletronicos Ltda., began activities in October 2008 and, in August 2009, decided to establish a procedure for monitoring tests, external and internal, of all packages received from customers, containing instruments for calibration. The aim was to investigate possible contamination radioactive on these instruments. On July 2011, this procedure was extended to packagings of personal thermoluminescent dosemeters - TLD, received by the newly created Laboratory Laboratorio de Dosimetria Pessoal - LDP . In the monitoring procedure were used monitors with external probe, type pancake, MRA brand, models GP - 500 and MIR 7028. During the 37 months in which this investigation was conducted, were detected 42 cases of radioactive contamination, with the following characteristics: 1) just one case was personal dosimeter, TLD type; 2) just one case was not from a packing from nuclear medicine service - was from a mining company; 3) contamination occurred on packs and instruments, located and/or widespread; 4) contamination values ranged from slightly above the level of background radiation to about a thousand fold. Although METROBRAS has facilities for decontamination, in most cases, especially those of higher contamination, the procedure followed was to store the contaminated material in a room used for storage of radioactive sources. Periodically, each package and/or instrument was monitored, being released when the radiation level matched the background radiation. Every contamination detected, the client and/or owner of the instrument was informed. The Brazilian National Energy Commission - CNEN, was informed, during your public consultation for reviewing the standard for nuclear medicine services, held in mid-2012, having received from METROBRAS the statistical data available at the time. The high frequency of contamination detected and the high

  11. Analysis on the influence of forest soil characteristics on radioactive Cs infiltration and evaluation of residual radioactive Cs on surfaces.

    Science.gov (United States)

    Mori, Yoshitomo; Yoneda, Minoru; Shimada, Yoko; Fukutani, Satoshi; Ikegami, Maiko; Shimomura, Ryohei

    2018-03-29

    We investigated the depth profiles of radioactive Cs, ignition loss, and cation exchange capacity (CEC) in five types of forest soils sampled using scraper plates. We then simulated the monitored depth profiles in a compartment model, taking ignition loss as a parameter based on experimental results showing a positive correlation between ignition loss and the CEC. The calculated values were comparable with the monitored values, though some discrepancy was observed in the middle of the soil layer. Based on decontamination data on the surface dose rate and surface contamination concentration, we newly defined a surface residual index (SRI) to evaluate the residual radioactive Cs on surfaces. The SRI value tended to gradually decrease in forests and unpaved roads and was much smaller in forests and on unpaved roads than on paved roads. The radioactive Cs was assumed to have already infiltrated underground 18 months after the nuclear power plant accident, and the sinking was assumed to be ongoing. The SRI values measured on paved roads suggested that radioactive Cs remained on the surfaces, though a gradual infiltration was observed towards the end of the monitoring term. The SRI value is thought to be effective in grasping the rough condition of residual radioactive Cs quickly at sites of decontamination activity in the field. The SRI value may be serviceable for actual contamination works after further research is done to elucidate points such as the relation between the SRI and the infiltration of radioactive Cs in various types of objects.

  12. Radiation exposure to skin following radioactive contamination

    International Nuclear Information System (INIS)

    Baumann, H.; Beyermann, M.; Kraus, W.

    1989-01-01

    In the case of skin contamination intensive decontamination measures should not be carried out until the potential radiation exposure to the basal cell layer of the epidermis was assessed. Dose equivalent rates from alpha-, beta- or photon-emitting contaminants were calculated with reference to the surface activity for different skin regions as a function of radiation energy on the condition that the skin was healthy and uninjured and the penetration of contaminants through the epidermis negligible. The results have been presented in the form of figures and tables. In the assessment of potential skin doses, both radioactive decay and practical experience as to the decrease in the level of surface contamination by natural desquamation of the stratum corneum were taken into account. 9 figs., 5 tabs., 46 refs. (author)

  13. Radioactive contamination of aquatic media and organisms

    International Nuclear Information System (INIS)

    Fontaine, Y.

    1960-01-01

    After a brief account of the radioactive wastes produced by peaceful or military uses of Atomic Industry, the author first describes a series of observations carried out 'in the field' on the extent of contamination in aquatic organisms with respect to that of the medium. The experimental studies are then analysed, with reference both to the radioisotope metabolism and to the factors and types of contamination of aquatic organisms by wastes from atomic industry. A precise experimental project is presented at the end of the paper, including almost 300 references. (author) [fr

  14. Radioactive contamination of natural and artificial materials

    International Nuclear Information System (INIS)

    Kovalchuk, E.L.; Pomansky, A.A.; Smolnikov, A.A.; Temmoev, A.H.

    1980-01-01

    The gamma radiation of different materials was measured in an underground low-background chamber with extraordinary background characteristics. The excellent background conditions of the measurements enabled investigators to see the alpha-particle peaks of the internal radioactive contamination of NaI(Tl) detectors, which were especially made for these measurements. The sensitivity limit of the installation was determined by the internal contamination of the NaI(Tl) detectors alone. Any radiation background, except for three substances, tungsten, copper, and brass, could be registered

  15. An overview of sites contaminated by radioactivity

    International Nuclear Information System (INIS)

    Eisenbud, M.

    1991-01-01

    This paper discusses contamination of land and water by radioactive material which is a subject that has been receiving widespread media attention, and has become the cause of much public anxiety. The contaminated sites can be divided broadly into three groups: Those that are quite old, relatively small in size, and the legacy of non-nuclear industrial activities involved with natural radioactivity, mostly in the early part of the century; the chain of uranium extraction plants used during and shortly after World War II, and the plants and laboratories that comprise the Department of Energy (DOE) research and weapons production complex today. It is the latter group that is the focus of greatest public attention at the present time

  16. Method of decontaminating radioactive-contaminated instruments

    International Nuclear Information System (INIS)

    Urata, Megumu; Fujii, Masaaki; Kitaguchi, Hiroshi.

    1982-01-01

    Purpose: To enable safety processing of liquid wastes by recovering radioactive metal ions remaining in the electrolytes after the decontamination procedure thereby decreasing the radioactivity. Method: In a decontamination tank containing electrolytes consisting of diluted hydrochloric acid and diluted sulfuric acid, are provided a radioactive contaminated instrument connected to an anode and a collector electrode made of stainless steel connected to a cathode respectively. Upon applying electrical current, the portion of the mother material to be decontaminated is polished electrolytically into metal ions and they are deposited as metal on the collection electrode. After completion of the decontamination, an ultrasonic wave generator is operated to strip and remove the oxide films. Thereafter, the anode is replaced with the carbon electrode and electrical current is supplied continuously, whereby the remaining metal ions are deposited and recovered as the metal on the collection electrode. (Yoshino, Y.)

  17. Method of decontaminating radioactive-contaminated instruments

    Energy Technology Data Exchange (ETDEWEB)

    Urata, M; Fujii, M; Kitaguchi, H

    1982-03-29

    Purpose: To enable safety processing of liquid wastes by recovering radioactive metal ions remaining in the electrolytes after the decontamination procedure thereby decreasing the radioactivity. Method: In a decontamination tank containing electrolytes consisting of diluted hydrochloric acid and diluted sulfuric acid, are provided a radioactive contaminated instrument connected to an anode and a collector electrode made of stainless steel connected to a cathode respectively. Upon applying electrical current, the portion of the mother material to be decontaminated is polished electrolytically into metal ions and they are deposited as metal on the collection electrode. After completion of the decontamination, an ultrasonic wave generator is operated to strip and remove the oxide films. Thereafter, the anode is replaced with the carbon electrode and electrical current is supplied continuously, whereby the remaining metal ions are deposited and recovered as the metal on the collection electrode.

  18. PROCESS OF DECONTAMINATING MATERIAL CONTAMINATED WITH RADIOACTIVITY

    Science.gov (United States)

    Overholt, D.C.; Peterson, M.D.; Acken, M.F.

    1958-09-16

    A process is described for decontaminating metallic objects, such as stainless steel equipment, which consists in contacting such objects with nltric acid in a concentration of 35 to 60% to remove the major portion of the contamination; and thereafter contacting the partially decontaminated object with a second solution containing up to 20% of alkali metal hydroxide and up to 20% sodium tartrate to remove the remaining radioactive contaminats.

  19. Residues and contaminants in tea and tea infusions: a review.

    Science.gov (United States)

    Abd El-Aty, A M; Choi, Jeong-Heui; Rahman, Md Musfiqur; Kim, Sung-Woo; Tosun, Alev; Shim, Jae-Han

    2014-01-01

    Consumers are very aware of contaminants that could pose potential health hazards. Most people drink tea as an infusion (adding hot water); however, in some countries, including India, China and Egypt, tea is drunk as a decoction (tea and water are boiled together). An infusion usually brings the soluble ingredients into solution, whereas a decoction brings all soluble and non-soluble constituents together. Therefore, a cup of tea may contain various kinds of contaminants. This review focuses on green and black tea because they are most commonly consumed. The target was to examine the transfer rate of contaminants - pesticides, environmental pollutants, mycotoxins, microorganisms, toxic heavy metals, radioactive isotopes (radionuclides) and plant growth regulators - from tea to infusion/brewing, factors contributing to the transfer potential and contaminants degradation, and residues in or on the spent leaves. It is concluded that most contaminants leaching into tea infusion are not detected or are detected at a level lower than the regulatory limits. However, the traditional practice of over-boiling tea leaves should be discouraged as there may be a chance for more transfer of contaminants from the tea to the brew.

  20. Radioactive contamination incidents involving protective clothing

    International Nuclear Information System (INIS)

    Reichelt, R.A.; Clay, M.E.; Eichorst, A.J.

    1998-01-01

    The study focuses on incidents at Department of Energy facilities involving the migration of radioactive contaminants through protective clothing. The authors analyzed 68 occurrence reports for the following factors: (1) type of work, (2) working conditions, (3) type of anti-contamination material; (4) area of body or clothing contaminated; and (5) nature of spread of contamination. A majority of reports identified strenuous work activities such as maintenance, construction, or decontamination and decommissioning projects. The reports also indicated adverse working conditions that included hot and humid or cramped work environments. The type of anti-contamination clothing most often identified was cotton or water-resistant disposable clothing. Most of the reports also indicated contaminants migrating through perspiration-soaked areas, typically in the knees and forearms. On the basis of their survey, the authors recommend the use of improved engineering controls and resilient, breathable, waterproof protective clothing for work in hot, humid, or damp areas where the possibility of prolonged contact with contamination cannot be easily avoided or controlled. 1 ref., 6 figs., 1 tab

  1. Radioactive contamination of the Yenisei River

    International Nuclear Information System (INIS)

    Vakulovsky, S.M.; Kryshev, I.I.; Nikitin, A.I.; Savitsky, Y.V.; Malyshev, S.V.; Tertyshnik, E.G.

    1995-01-01

    Based on observational data in the period 1971-1993, radioactive contamination of the Yenisei River ecosystem was analysed within 2000 km of the site of discharges from the Krasnoyarsk Mining and Chemical Industrial Complex. Data on the content of 24 Na, 32 P, 46 Sc, 51 Cr, 54 Mn, 56 Mn, 58 Co, 60 Co, 59 Fe, 65 Zn, 90 Sr, 95 Zr, 95 Nb, 103 Ru, 106 Ru, 134 Cs, 137 Cs, 140 Ba, 141 Ce, 144 Ce and 239 Np in the river ecosystem components were generalised. Radioactive contamination of water in the near zone of discharges (within 15 km) was shown to be determine mainly by the short-lived nuclides, such as 24 Na, 32 P, 56 Mn and 239 Np, as well as 51 Cr. Outside the near zone the water contamination level decreased appreciably. According to observational data of 1973, the total contamination inventory of the river bottom in the near zone was as great as 5800 kBq m -2 . More than half was accounted for by two radionuclides: 51 Cr and 65 Zn. At a distance of 1930 km from the site of discharges a technogenic activity of bottom sediments amounted to 5 kBq m -2 and was accounted for by 137 Cs and 65 Zn. The main radionuclide accumulated in fish was 32 P. Exposure doses to aquatic organisms and population were assessed in the near and far zones of the Krasnoyarsk radioactive contamination trace. Within 250 km of the site of discharges the exposure dose to the population from a consumption of 1 kg of fish was shown to amount to an average of 10 μSv. (author)

  2. Summary of the engineering assessment of radioactive sands and residues, Lowman Site, Lowman, Idaho

    International Nuclear Information System (INIS)

    1981-09-01

    Ford, Bacon and Davis Utah Inc. has reevaluated the Lowman site in order to revise the December 1977 engineering assessment of the problems resulting from the existence of radioactive sands and residues at Lowman, Idaho. This engineering assessment has included the preparation of topographic maps, the performance of core drillings and radiometric measurements sufficient to determine areas and volumes of radioactive sands and residues and radiation exposures of individuals and nearby populations, the investigations of site hydrology and meteorology, and the evaluation and costing of alternative corrective actions. Radon gas released from the 191,000 tons of radioactive sands, residues, and contaminated soils at the Lowman site constitutes the most significant environmental impact, although windblown radioactive sands and external gamma radiation also are factors

  3. Engineering assessment of radioactive sands and residues, Lowman Site, Lowman, Idaho

    International Nuclear Information System (INIS)

    1981-09-01

    Ford, Bacon and Davis Utah Inc. has reevaluated the Lowman site in order to revise the December 1977 engineering assessment of the problems resulting from the existence of radioactive sands and residues at Lowman, Idaho. This engineering assessment has included the preparation of topographic maps, the performance of core drillings and radiometric measurements sufficient to determine areas and volumes of radioactive sands and residues and radiation exposure of individuals and nearby populations, and investigations of site hydrology and meteorology, and the evaluation and costing of alternative corrective actions. Radon gas released from the 191,000 tons of radioactive sands, residues, and contaminated soils at the Lowman site constitutes the most significant environmental impact, although windblown radioactive sands and external gamma radiation also are factors

  4. Development of high-level radioactive waste treatment and conversion technologies 'Dry decontamination technology development for highly radioactive contaminants'

    Energy Technology Data Exchange (ETDEWEB)

    Oh, Won Zin; Lee, K. W.; Won, H. J.; Jung, C. J.; Choi, W. K.; Kim, G. N.; Moon, J. K

    2001-04-01

    The followings were studied through the project entitled 'Dry Decontamination Technology Development for Highly Radioactive Contaminants'. 1.Contaminant Characteristics Analysis of Domestic Nuclear Fuel Cycle Projects(NFCP) and Applicability Study of the Unit Dry-Decontamination Techniques A. Classification of contaminated equipments and characteristics analysis of contaminants B. Applicability study of the unit dry-decontamination techniques 2.Performance Evaluation of Unit Dry Decontamination Technique A. PFC decontamination technique B. CO2 decontamination technique C. Plasma decontamination technique 3.Development of Residual Radiation Assessment Methodology for High Radioactive Facility Decontamination A. Development of radioactive nuclide diffusion model on highly radioactive facility structure B. Obtainment of the procedure for assessment of residual radiation dose 4.Establishment of the Design Concept of Dry Decontamination Process Equipment Applicable to Highly Radioactive Contaminants 5.TRIGA soil unit decontamination technology development A. Development of soil washing and flushing technologies B. Development of electrokinetic soil decontamination technology.

  5. Phytoremediation options for radioactively contaminated sites evaluated

    International Nuclear Information System (INIS)

    Vandenhove, Hildegarde

    2013-01-01

    Highlights: ► We present an overview of the most important site and environmental radioactive contamination problems encountered. ► The potential role of different phytomanagement options is discussed and illustrated with examples. ► The phytomanagement options considered are: soil phytoextraction, rhizofiltration, wetlands and alternative land use. - Abstract: The application of nuclear energy and the use of radionuclides for industrial, medical and research purposes have caused significant contamination of certain sites and their environment, which could result in health problems for several centuries if nothing is undertaken to remedy these situations. Except for the immediate environment of the facility, where decontamination activities may be feasible and affordable, the contamination often extents over a vast area and decontamination would be costly and could result in vast amounts of waste. Therefore, more realistic yet efficient remediation options should be searched for of which phytomanagement is among the potential options. A number of phytomanagement approaches will be discussed

  6. Radioactive contamination incidents involving protective clothing

    International Nuclear Information System (INIS)

    Reichelt, R.; Clay, M.; Eichorst, J.

    1996-10-01

    The study focuses on incidents at Department of Energy (DOE) facilities involving the migration of radioactive contaminants through protective clothing. The authors analyzed 68 occurrence reports for the following factors: (1) type of work; (2) working conditions; (3) type of anti-contamination (anti-C) material; (4) area of body or clothing contaminated; and (5) nature of spread of contamination. A majority of reports identified strenuous work activities such as maintenance, construction, or decontamination and decommissioning (D ampersand D) projects. The reports also indicated adverse working conditions that included hot and humid or cramped work environments. The type of anti-C clothing most often identified was cotton or water-resistant, disposable clothing. Most of the reports also indicated contaminants migrating through perspiration-soaked areas, typically in the knees and forearms. On the basis of their survey, the authors recommend the use of improved engineering controls and resilient, breathable, waterproof protective clothing for work in hot, humid, or damp areas where the possibility of prolonged contact with contamination cannot be easily avoided or controlled

  7. Radioactive contamination incidents involving protective clothing

    Energy Technology Data Exchange (ETDEWEB)

    Reichelt, R.; Clay, M.; Eichorst, J.

    1996-10-01

    The study focuses on incidents at Department of Energy (DOE) facilities involving the migration of radioactive contaminants through protective clothing. The authors analyzed 68 occurrence reports for the following factors: (1) type of work; (2) working conditions; (3) type of anti-contamination (anti-C) material; (4) area of body or clothing contaminated; and (5) nature of spread of contamination. A majority of reports identified strenuous work activities such as maintenance, construction, or decontamination and decommissioning (D&D) projects. The reports also indicated adverse working conditions that included hot and humid or cramped work environments. The type of anti-C clothing most often identified was cotton or water-resistant, disposable clothing. Most of the reports also indicated contaminants migrating through perspiration-soaked areas, typically in the knees and forearms. On the basis of their survey, the authors recommend the use of improved engineering controls and resilient, breathable, waterproof protective clothing for work in hot, humid, or damp areas where the possibility of prolonged contact with contamination cannot be easily avoided or controlled.

  8. Criteria for the designation of radioactively contaminated land

    International Nuclear Information System (INIS)

    Titley, J.; Mobbs, S.; Burgess, P.; Hitchins, G.; Sinclair, P.

    1999-01-01

    This report examines the criteria for the designation of radioactively contaminated land. It should be read in conjunction with reference to another output from the project i.e. Environment Agency report, Technical Support Material for the Regulation of Radioactively Contaminated Land 1999. This report deals with the intervention on radioactively contaminated sites i.e. where no change of land use is anticipated and where the land has become contaminated as a result of previous land use and not current practices. (author)

  9. Ecological Role of Soils upon Radioactive Contamination

    Science.gov (United States)

    Tsvetnov, Evgeny; Shcheglov, Alexei; Tsvenova, Olga

    2016-04-01

    The ecological role of soils upon radioactive contamination is clearly manifested in the system of notions about ecosystems services, i.e., benefits gained by humans from ecosystems and their components, including soils (Millennium Ecosystem Assessment, 2005). For the soils, these services are considered on the basis of soil functions in the biosphere that belong to the protective ecosystem functions within the group of soil functions known under the names of "Buffer and protective biogeocenotic shield" (at the level of particular biogeocenoses) and "Protective shield of the biosphere" (at the global biospheric level) (according to Dobrovol'skii & Nikitin, 2005). With respect to radionuclides, this group includes (1) the depositing function, i.e., the accumulation and long-term sequestration of radioactive substances by the soil after atmospheric fallout; (2) the geochemical function, i.e., the regulation of horizontal and vertical fluxes of radionuclides in the system of geochemically conjugated landscapes and in the soil-groundwater and soil-plant systems; and (3) the dose-forming function that is manifested by the shielding capacity of the soil with respect to the external ionizing radiation (lowering of the dose from external radiation) and by the regulation of the migration of radionuclides in the trophic chain (lowering of the dose from internal radiation). The depositing and geochemical functions of the soils are interrelated, which is seen from quantitative estimates of the dynamics of the fluxes of radionuclides in the considered systems (soil-plant, soil-groundwater, etc.). The downward migration of radionuclides into the lower soil layers proceeds very slowly: for decades, more than 90% of the pool of radionuclides is stored in the topmost 10 cm of the soil profile. In the first 3-5 years after the fallout, the downward migration of radionuclides with infiltrating water flows decreases from several percent to decimals and hundredths of percent from the

  10. Phytoremediation of water bodies contaminated with radioactive heavy metal

    International Nuclear Information System (INIS)

    Yan Zhen; Yuan Shichao; Ling Hui; Xie Shuibo

    2012-01-01

    The sources of the radioactive heavy metal in the water bodies were analyzed. The factors that affect phyto remediation of water contaminated with radioactive heavy metal were discussed. The plant species, mechanism and major technology of phyto remediation of water contaminated with radioactive heavy metal were particularly introduced. The prospective study was remarked. (authors)

  11. Environmental radioactive contamination and its control for nuclear power plants

    International Nuclear Information System (INIS)

    Shi Zhongqi; Qu Jingyuan; Cui Yongli

    1998-01-01

    The environmental radioactive releases and exposure to human being due to operation of nuclear power plants in the world and in China, environmental contamination and consequences caused by severe nuclear power plant accidents in the history, control of the radioactive contamination in China, and some nuclear laws on the radioactive contamination control established by international organizations and USA etc. are described according to literature investigation and research. Some problems and comments in radioactive contamination control for nuclear power plants in China are presented. Therefore, perfecting laws and regulations and enhancing surveillances on the contamination control are recommended

  12. [Decorporation agents for internal radioactive contamination].

    Science.gov (United States)

    Ohmachi, Yasushi

    2015-01-01

    When radionuclides are accidentally ingested or inhaled, blood circulation or tissue/organ deposition of the radionuclides causes systemic or local radiation effects. In such cases, decorporation therapy is used to reduce the health risks due to their intake. Decorporation therapy includes reduction and/or inhibition of absorption from the gastrointestinal tract, isotopic dilution, and the use of diuretics, adsorbents, and chelating agents. For example, penicillamine is recommended as a chelating agent for copper contamination, and diethylene triamine pentaacetic acid is approved for the treatment of internal contamination with plutonium. During chelation therapy, the removal effect of the drugs should be monitored using a whole-body counter and/or bioassay. Some authorities, such as the National Council on Radiation Protection and Measurements and International Atomic Energy Agency, have reported recommended decorporation agents for each radionuclide. However, few drugs are approved by the US Food and Drug Administration, and many are off-label-use agents. Because many decontamination agents are drugs that have been available for a long time and have limited efficacy, the development of new, higher-efficacy drugs has been carried out mainly in the USA and France. In this article, in addition to an outline of decorporation agents for internal radioactive contamination, an outline of our research on decorporation agents for actinide (uranium and plutonium) contamination and for radio-cesium contamination is also presented.

  13. Remediation of sites with dispersed radioactive contamination

    International Nuclear Information System (INIS)

    2004-01-01

    To respond to the needs of Member States, the IAEA launched an environmental remediation project to deal with the problems of radioactive contamination worldwide. The IAEA environmental remediation project includes an IAEA Coordinated Research Project, as well as the participation of IAEA experts in concrete remediation projects when requested by individual Member States. The IAEA has prepared several documents dedicated to particular technical or conceptual areas, including documents on the characterization of contaminated sites, technical and non-technical factors relevant to the selection of a preferred remediation strategy and technique, overview of applicable techniques for environmental remediation,, options for the cleanup of contaminated groundwater and planning and management issues. In addition, a number of other IAEA publications dealing with related aspects have been compiled under different IAEA projects; these include TECDOCs on the remediation of uranium mill tailings, the decontamination of buildings and roads and the characterization of decommissioned sites. Detailed procedures for the planning and implementation of remedial measures have been developed over the past decade or so. A critical element is the characterization of the contamination and of the various environmental compartments in which it is found, in order to be able to evaluate the applicability of remediation techniques. The chemical or mineralogical form of the contaminant will critically influence the efficiency of the remediation technique chosen. Careful delineation of the contamination will ensure that only those areas or volumes of material that are actually contaminated are treated. This, in turn, reduces the amount of any secondary waste generated. The application of a remediation technique requires holistic studies examining the technical feasibility of the proposed measures, including analyses of their impact. Consequently, input from various scientific and engineering

  14. A radiological legacy. Radioactive residues of the Cold War period

    International Nuclear Information System (INIS)

    Gonzalez, A.J.

    1998-01-01

    A dominating feature of the historical period known as the Cold War was the large-scale production and testing, of nuclear weapons. These military activities brought with them an unprecedented generation of radioactive substances. A fraction of these 'Cold War residues' ended up in the atmosphere and were dispersed throughout the world. Some remained in relatively isolated states in underground geological environments at the production or test site. Others have contaminated areas at times accessible to humans. Augmenting this picture are other scenes of a Cold War legacy. Large amounts of radioactive waste and byproducts are in storage from the production of weapons material. At some point, they are expected to be converted to peaceful applications or sent for final disposal. Over the past decade, the IAEA has been asked to play a greater role in helping countries address this Cold War legacy. A number of scientific assessments of radiological situations created by the Cold War have been carried out by experts convened by the IAEA - at nuclear test sites, nuclear production facilities, and waste dumping sites. This edition of the IAEA Bulletin highlights these cooperative activities in the context of international developments and concerns

  15. Survey of radioactive contamination of foodstuffs

    International Nuclear Information System (INIS)

    Lee, W. R.; Lee, C. W.; Choi, G. S.; Cho, Y. H.; Kang, M. J.; Cheong, K. H.; Kim, H. R.; Kwak, J. Y.

    2005-11-01

    The purpose of this study is to survey and assess radioactive contamination of foodstuffs in order to reduce the probability of intake of contaminated foodstuffs. Based on survey and assessment, final goal is to improve the public health by radiation protection. Sampled foodstuffs items are collected from the markets : one group are imported foodstuffs and the other group are domestic foodstuffs producted around nuclear facilities. After pretreatments such as drying, ashing, and homogenization, all samples were analyzed by gamma spectrometer system. The 137 Cs radionuclide was only measured among the regulation radionuclides ( 137 Cs, 134 Cs, 131 I) of food code. All radionuclides of the domestic foodstuffs collected around nuclear facilities were below Minimum Detectable Activity (MDA). But the activity concentrations of Inonotus obliquus (Chaga mushooms) from Russia ranged up to 171.27 (average value : 36.65) Bq/kg-fresh. In the case of blueberry jam, the radioactivity of 137 Cs is higher than expected value. Other samples are below MDA except some spices. Based on the previous and present results, it should be strengthen to survey for Inontus obliquus (Chaga mushooms), of which the radioactivity shows the range from MDA up to 800.01 Bq/kg-fresh. It should assess the public radiation exposure via food chain because it has the excess provability of the maximum permitted level of food code, which is regulation of KFDA. The development method based on international standard would be used at radioactive analysis as well as education of practical workers and it could be applied as the basis data for amending the analysis method of food code. Our country only surveys gamma emitting radionuclides till now but international organization or foreign countries for example EU survey alpha and beta emitting radionuclides as well as gamma emitting radionuclides. So our country should also research necessity of survey for alpha and beta emitting radionuclides

  16. Survey of radioactive contamination of foodstuffs

    Energy Technology Data Exchange (ETDEWEB)

    Lee, W. R.; Lee, C. W.; Choi, G. S.; Cho, Y. H.; Kang, M. J.; Cheong, K. H.; Kim, H. R.; Kwak, J. Y

    2005-11-15

    The purpose of this study is to survey and assess radioactive contamination of foodstuffs in order to reduce the probability of intake of contaminated foodstuffs. Based on survey and assessment, final goal is to improve the public health by radiation protection. Sampled foodstuffs items are collected from the markets : one group are imported foodstuffs and the other group are domestic foodstuffs producted around nuclear facilities. After pretreatments such as drying, ashing, and homogenization, all samples were analyzed by gamma spectrometer system. The {sup 137}Cs radionuclide was only measured among the regulation radionuclides ({sup 137}Cs, {sup 134}Cs, {sup 131}I) of food code. All radionuclides of the domestic foodstuffs collected around nuclear facilities were below Minimum Detectable Activity (MDA). But the activity concentrations of Inonotus obliquus (Chaga mushooms) from Russia ranged up to 171.27 (average value : 36.65) Bq/kg-fresh. In the case of blueberry jam, the radioactivity of {sup 137}Cs is higher than expected value. Other samples are below MDA except some spices. Based on the previous and present results, it should be strengthen to survey for Inontus obliquus (Chaga mushooms), of which the radioactivity shows the range from MDA up to 800.01 Bq/kg-fresh. It should assess the public radiation exposure via food chain because it has the excess provability of the maximum permitted level of food code, which is regulation of KFDA. The development method based on international standard would be used at radioactive analysis as well as education of practical workers and it could be applied as the basis data for amending the analysis method of food code. Our country only surveys gamma emitting radionuclides till now but international organization or foreign countries for example EU survey alpha and beta emitting radionuclides as well as gamma emitting radionuclides. So our country should also research necessity of survey for alpha and beta emitting

  17. 10 CFR 39.69 - Radioactive contamination control.

    Science.gov (United States)

    2010-01-01

    ... 10 Energy 1 2010-01-01 2010-01-01 false Radioactive contamination control. 39.69 Section 39.69... Radiation Safety Requirements § 39.69 Radioactive contamination control. (a) If the licensee detects evidence that a sealed source has ruptured or licensed materials have caused contamination, the licensee...

  18. Radioactive wastes and residues: government participation in a control policy

    International Nuclear Information System (INIS)

    Gelli, Guido

    1993-01-01

    This paper discusses the politic aspects of the State participation in inspection and control of the radioactive wastes residues with the supervise of Brazilian Nuclear Energy Commission (CNEN), by a national program

  19. Radioactive contamination, what actions for the polluted sites; Contamination radioactive, quelles actions pour les sites pollues

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2004-07-01

    The nuclear safety authority and the direction of prevention of pollutions and risks have organised the first edition of the national colloquium: radioactive contamination: what actions for polluted sites. Four axes can be taken to follow this colloquium: prevention, outstanding tools to evaluate risks and rehabilitation, a better responsibility of operators and memory keeping. (N.C.)

  20. Responses of the soil decomposer community to the radioactive contamination

    International Nuclear Information System (INIS)

    Svetlana, Maksimova

    2004-01-01

    radioactive plots had considerable changes in the physiology. Based on the results of our study, we have a conclusion the decomposer community exposed to irradiation for a long time reacts clearly by a noticeable suppression. Furthermore, the results also demonstrated that there was a strong relation between decomposition rates and numbers of decomposer fauna present in soil layers. Given the important role of decomposer invertebrates in the development and maintenance of soil structure, and in the incorporation and breakdown of organic residues in the soil, we made conclusion that the reduction of density and biodiversity of decomposer organisms in the radio-contaminated zone produced long term effects on the soil health. (author)

  1. Responses of the soil decomposer community to the radioactive contamination

    Energy Technology Data Exchange (ETDEWEB)

    Svetlana, Maksimova [Institute of Zoology of National Academy of Sciences of Belarus, Minsk (Belarus)

    2004-07-01

    radioactive plots had considerable changes in the physiology. Based on the results of our study, we have a conclusion the decomposer community exposed to irradiation for a long time reacts clearly by a noticeable suppression. Furthermore, the results also demonstrated that there was a strong relation between decomposition rates and numbers of decomposer fauna present in soil layers. Given the important role of decomposer invertebrates in the development and maintenance of soil structure, and in the incorporation and breakdown of organic residues in the soil, we made conclusion that the reduction of density and biodiversity of decomposer organisms in the radio-contaminated zone produced long term effects on the soil health. (author)

  2. Risk assessment methodology for evaluating releases of radioactively contaminated materials

    International Nuclear Information System (INIS)

    Chen, S.Y.

    1993-01-01

    Extensive decontamination and decommissioning (D ampersand D) activities are expected to be required in the near future in association with license termination of nuclear power facilities and cleanup efforts at the U.S. Department of Energy's (DOE's) weapons production facilities. In advance of these D ampersand D activities, it is becoming increasingly urgent that standards be established for the release of materials with residual radioactive contamination. The only standards for unrestricted release that currently exist address surface contamination. The methods used to justify those standards were developed some 20 yr ago and may not satisfy today's criteria. Furthermore, the basis of setting standards has moved away from the traditional open-quotes instrumentation-basedclose quotes concept toward a open-quotes risk-basedclose quotes approach. Therefore, as new release standards are developed, it will be necessary that risk assessment methodology consistent with modern concepts be incorporated into the process. This paper discusses recent developments in risk methodology and issues and concerns regarding the future development of standards for the release of radioactively contaminated materials

  3. Packaging and transportation of radioactively contaminated lead

    International Nuclear Information System (INIS)

    Gleason, Eugene; Holden, Gerard

    2007-01-01

    Under the management of the Nuclear Decommissioning Authority (NDA) the government of the United Kingdom has launched an ambitious program to remediate the nation's nuclear waste legacy. Over a twenty-five year period NDA plans to decommission several first generation nuclear power plants and other radioactive facilities. The use innovative, safe 'fit for purpose' technologies will be a major part of this complex program. This paper will present a case study of a recently completed project undertaken in support of the nuclear decommissioning activities at the Sellafield site in the United Kingdom. The focus is on an innovative application of new packaging technology developed for the safe transportation of radioactively contaminated lead objects. Several companies collaborated on the project and contributed to its safe and successful conclusion. These companies include British Nuclear Group, Gravatom Engineering, W. F. Bowker Transport, Atlantic Container Lines, MHF Logistical Solutions and Energy Solutions. New containers and a new innovative inter-modal packaging system to transport the radioactive lead were developed and demonstrated during the project. The project also demonstrated the potential contribution of international nuclear recycling activities as a safe, economic and feasible technical option for nuclear decommissioning in the United Kingdom. (authors)

  4. Worker exposures from recycling surface contaminated radioactive scrap metal

    International Nuclear Information System (INIS)

    Kluk, A.; Phillips, J.W.; Culp, J.

    1996-01-01

    Current DOE policy permits release from DOE control of real property with residual levels of surficial radioactive contamination if the contamination is below approved guidelines. If the material contains contamination that is evenly distributed throughout its volume (referred to as volumetric contamination), then Departmental approval for release must be obtained in advance. Several DOE sites presently recycle surface contaminated metal, although the quantities are small relative to the quantities of metal processed by typical mini-mills, hence the potential radiation exposures to mill workers from processing DOE metals and the public from the processed metal are at present also a very small fraction of their potential value. The exposures calculated in this analysis are based on 100% of the scrap metal being processed at the maximum contamination levels and are therefore assumed to be maximum values and not likely to occur in actual practice. This paper examines the relationship between the surface contamination limits established under DOE Order 5400.5, open-quotes Radiation Protection of the Public and the Environment,close quotes and radiation exposures to workers involved in the scrap metal recycling process. The analysis is limited to surficial contamination at or below the guideline levels established in DOE Order 5400.5 at the time of release. Workers involved in the melting and subsequent fabrication of products are not considered radiation workers (no requirements for monitoring) and must be considered members of the public. The majority of the exposures calculated in this analysis range from tenths of a millirem per year (mrem/yr) to less than 5 mrem/yr. The incremental risk of cancer associated with these exposures ranges from 10 -8 cancers per year to 10 -6 cancers per year

  5. A manual for implementing residual radioactive material guidelines

    International Nuclear Information System (INIS)

    Gilbert, T.L.; Yu, C.; Yuan, Y.C.; Zielen, A.J.; Jusko, M.J.; Wallo, A. III; Argonne National Lab., IL; Dames and Moore, West Valley, NY; Argonne National Lab., IL; USDOE Assistant Secretary for Nuclear Energy, Washington, DC

    1989-06-01

    This manual presents information for implementing US Department of Energy (DOE) guidelines for residual radioactive material at sites identified by the Formerly Utilized Sites Remedial Action Program (FUSRAP) and the Surplus Facilities Management Program (SFMP). It describes the analysis and models used to derive site-specific guidelines for allowable residual concentrations of radionuclides in soil and the design and use of the RESRAD computer code for calculating guideline values. It also describes procedures for implementing DOE policy for reducing residual radioactivity to levels that are as low as reasonably achievable. 36 refs., 16 figs, 22 tabs

  6. Radioactive contamination in the Arctic - Present situation and future challenges

    International Nuclear Information System (INIS)

    Strand, P.

    2002-01-01

    There is currently a focus on radioactivity and the Arctic region. The reason for this is the high number of nuclear sources in parts of the Arctic and the vulnerability of Arctic systems to radioactive contamination. The Arctic environment is also perceived as a wilderness and the need for the protection of this wilderness against contamination is great. In 1991, the International Arctic Environmental Protection Strategy (IAEPS) was launched and the Arctic Monitoring and Assessment Programme (AMAP) established. AMAP is undertaking an assessment of the radioactive contamination of the Arctic and its radiological consequences. This paper summarises some of current knowledge about sources of radioactive contamination, vulnerability, exposure of man, and potential sources for radioactive contamination within Arctic and some views on the future needs for work concerning radioactivity in Arctic. (author)

  7. Radioactive Contamination of Agricultural Products in Poland

    International Nuclear Information System (INIS)

    Muszynski, W.; Grabowski, D.; Rubel, B.; Kurowski, W.; Swietochowska, J.; Smagala, G.

    2003-01-01

    Radiological contamination of the environment is caused by nuclear activities on the globe: nuclear weapon tests and the Chernobyl accident. The transfer of radionuclides to the organism via ingestion is one of the sources of doses obtained by people. To assess the doses received by humans the intake of isotopes with daily diet was defined. The concentration of radionuclides in foodstuffs was determined. The network of Service for Measurement of Radioactive Contamination systematically controls all kinds of important agricultural products such as milk, meat, vegetables, fruit, cereals and forest products: mushrooms, blueberries etc. Measurement stations involved in food monitoring act within Sanitary-Epidemiological Stations, Veterinary Hygiene Units and Chemical-Agricultural Stations. All activities are co-ordinated by the Central Laboratory for Radiological Protection. The level of activity of caesium isotopes has regularly been monitored in collected samples originating from different administrative districts of Poland. Since 1994 the 134 Cs concentration has been below the detection limit. The activity of 137 Cs has been measured to determine long-term effect of the accident on the contamination of milk, meat and other foodstuffs. (orig.)

  8. Radiological Risk Assessment and Survey of Radioactive Contamination for Foodstuffs

    International Nuclear Information System (INIS)

    Lee, W.R.; Lee, C.W.; Choi, K.S.

    2007-11-01

    After the Chernobyl nuclear accident in 1986, a radiological dose assessment and a survey of a radioactive contamination for foodstuffs have been investigated by many countries such as EU, Japan, USA. In the case of Japan which is similar to our country for the imported regions of foodstuffs, there were some instances of the excess for regulation on the maximum permitted levels of radioactive contamination among some imported foodstuffs. Concerns about the radioactive contamination of foodstuffs are increased because of the recently special situation (Nuclear test of North Korea). The purpose of this study is a radiological dose assessment and a survey of a radioactive contamination for foodstuffs in order to reduce the probability of intake of contaminated foodstuffs. Analytical results of the collected samples are below MDA. In this project, the model of radiological dose assessment via the food chain was also developed and radiological dose assessment was conducted based on surveys results of a radioactive contamination for foodstuffs in the Korean open markets since 2002. The results of radiological dose assessment are far below international reference level. It shows that public radiation exposure via food chain is well controlled within the international guide level. However, the radioactive contamination research of imported foodstuffs should be continuous considering the special situation(nuclear test of North Korea). These results are used to manage the radioactive contamination of the imported foodstuffs and also amend the regulation on the maximum permitted levels of radioactive contamination of foodstuffs

  9. 76 FR 42074 - Consideration of Rulemaking To Address Prompt Remediation of Residual Radioactivity During...

    Science.gov (United States)

    2011-07-18

    ... Address Prompt Remediation of Residual Radioactivity During Operations AGENCY: Nuclear Regulatory... radioactivity during the operational phase of licensed material sites and nuclear reactors. The NRC has not... to the decommissioning planning process by addressing remediation of residual radioactivity during...

  10. 78 FR 33008 - Consideration of Rulemaking To Address Prompt Remediation of Residual Radioactivity During...

    Science.gov (United States)

    2013-06-03

    ...-0162] Consideration of Rulemaking To Address Prompt Remediation of Residual Radioactivity During... address prompt remediation of residual radioactivity during the operational phase of licensed material... radioactivity during the operational phase with the objective of avoiding complex decommissioning challenges...

  11. Radioactive contamination of the marine environment

    International Nuclear Information System (INIS)

    Aarkrog, A.

    1997-01-01

    The major source of man-made radioactivity in the oceans is derived from nuclear weapons testing fallout, which occurred mostly in the late 1950s and early 1960s. For example, 0.9 EBq of 137 Cs and 0.6 EBq of 90 Sr were introduced in this way. Only 60% of the released activity was disposed of in the oceans, rather than 70%, because the nuclear weapons testing occurred mainly in the Northern hemisphere, and the land masses cover more of the Northern hemisphere than the Southern hemisphere. There have also been other releases into the oceans; for example, the water-borne discharges from the Sellafield reprocessing plant in the UK, which occurred from the mid-1970s to the mid-1980s. During this decade, in the order of 40 PBq of 137 Cs was discharged into the Irish sea, and from there it was transported into the north Atlantic ocean. The third important source of radioactivity was the Chernobyl accident. Although most of this radioactivity was distributed over the land masses, about 5 PBq was deposited into the Baltic Sea and about 3 PBq into the Black Sea. The radioactive debris from Chernobyl was distributed around the Northern hemisphere, so some of the radioactivity must have been deposited in the North Atlantic ocean. There have also been a number of local contaminations of the oceans. Among these are satellite failures. For example, the SNAP-9A satellite, which burned up over the South Atlantic ocean in the early 1960s, became a major source of 238 Pu pollution. This is the reason why there is an increased 238 Pu: 239 Pu ratio, mostly in the Southern hemisphere, in global fallout. There are also a number of nuclear submarines on the bottom of the sea; for example, the American Thresher submarine in the Atlantic ocean and the Comsomolets submarine in the Norwegian-Barents sea. Furthermore, there have been several accidents with nuclear weapons; for example, the Palomares accident in Spain in 1966 and the Thule accident in Greenland in 1968. Finally, nuclear

  12. Sources of radioactive contamination inside houses

    International Nuclear Information System (INIS)

    Sajet, A.S.

    2010-01-01

    People may be exposed at home to multiple sources of nuclear radiation such as gamma, beta and alpha rays emitters. House atmosphere is polluted with nuclear radiation from water pollutants and rocks used in the construction. Radon is the only radioactive non-metallic element. Environmental organizations estimated that all houses contain varying concentrations of radon gas, and the residents are exposed to levels of radon over the years. The source of radon in houses is uranium, which may be found in rocks of the house, soil of the garden, water of the deep artesian wells and building materials, especially granite rocks. Breathing air that contains high levels of radon causes lung cancer. Radon is the second cause of lung disease after smoking. There are many means to reduce house pollution including: utilisation of air filters to remove contaminated dust particles, keep residential areas away from the establishments that use nuclear technology or embedded by nuclear waste, avoid using materials made from asbestos in construction works and proper use and disposal of chemicals and medicines containing radioactive isotopes. (author)

  13. Issues in recycling and disposal of radioactively contaminated materials

    International Nuclear Information System (INIS)

    Kluk, A.F.; Hocking, E.K.; Roberts, R.; Phillips, J.W.

    1993-01-01

    The Department of Energy's present stock of potentially re-usable and minimally radioactively contaminated materials will increase significantly as the Department's remediation activities expand. As part of its effort to minimize wastes, the Department is pursuing several approaches to recover valuable materials such as nickel, copper, and steel, and reduce the high disposal costs associated with contaminated materials. Key approaches are recycling radioactively contaminated materials or disposing of them as non-radioactive waste. These approaches are impeded by a combination of potentially conflicting Federal regulations, State actions, and Departmental policies. Actions to promote or implement these approaches at the Federal, State, or Departmental level involve issues which must be addressed and resolved. The paramount issue is the legal status of radioactively contaminated materials and the roles of the Federal and State governments in regulating those materials. Public involvement is crucial in the debate surrounding the fate of radioactively contaminated materials

  14. Thermal decomposition of woody wastes contaminated with radioactive materials using externally-heated horizontal kiln

    International Nuclear Information System (INIS)

    Iwasaki, Toshiyuki; Kato, Shigeru; Yamasaki, Akihiro; Ito, Takuya; Suzuki, Seiichi; Kojima, Toshinori; Kodera, Yoichi; Hatta, Akimichi; Kikuzato, Masahiro

    2015-01-01

    Thermal decomposition experiments of woody wastes contaminated with radioactive materials were conducted using an externally-heated horizontal kiln in the work area for segregation of disaster wastes at Hirono Town, Futaba County, Fukushima Prefecture. Radioactivity was not detected in gaseous products of thermal decomposition at 923 K and 1123 K after passage through a trap filled with activated carbon. The contents of radioactive cesium ( 134 Cs and 137 Cs) were measured in the solid and liquid products of the thermal decomposition experiments and in the residues in the kiln after all of the experiments. Although a trace amount of radioactive cesium was found in the washing trap during the start-up period of operation at 923 K, most of the cesium remained in the char, including the residues in the kiln. These results suggest that most of the radioactive cesium is trapped in char particles and is not emitted in gaseous form. (author)

  15. Relocation of radioactive residuals store: environment effects statement

    International Nuclear Information System (INIS)

    1984-11-01

    This Environment Effects Statement describes and assesses the likely environmental effects of the proposal to relocate the Health Commission's existing radioactive residuals store to a site within the established Dutson Downs waste disposal area, located 20 km south-east of Sale and 225 km east of Melbourne. The information presented demonstrates that the siting and construction of the proposed radioactive residuals store and the procedures to be adopted for the handling and storage of materials will not present an unacceptable risk to public health and safety, nor will it involve any significant adverse environmental effects

  16. Influence of radioactive contaminants on absorbed dose estimates for radiopharmaceuticals

    International Nuclear Information System (INIS)

    Watson, E.E.; Stabin, M.G.

    1986-01-01

    Several popular radiopharmaceutical products contain low levels of radioactive contaminants. These contaminants increase the radiation absorbed dose to the patient without any increased benefit and, in some cases, with a decrease in image quality. The importance of a contaminant to the radiation dosimetry picture is a function of 1) the contaminant level, 2) the physical half-life of the contaminant, 3) the organ uptake and the biological half-time of the contaminant in the various body systems, and 4) the decay mode, energy, etc. of the contaminant. The general influence of these parameters is discussed in this paper; families of curves are included that reflect the changing importance of contaminant dosimetry with respect to the primary radionuclide as a function of these variables. Several specific examples are also given of currently used radiopharmaceutical products which can contain radioactive contaminants (I-123, In-111, Tl-201, Ir-191m, Rb-82, Au-195m). 7 references, 8 figures, 4 tables

  17. Methods for removing radioactive isotopes from contaminated streams

    International Nuclear Information System (INIS)

    Hoy, D.R.; Hickey, T.N.; Spulgis, I.S.; Parish, H.C.

    1979-01-01

    Methods for removing radioactive isotopes from contaminated gas streams for use in atmospheric containment and cleanup systems in nuclear power plants are provided. The methods provide for removal of radioactive isotopes from a first portion of the contaminated stream, separated from the remaining portion of the stream, so that adsorbent used to purify the first portion of the contaminated stream by adsorption of the radioactive isotopes therefrom can be tested to determine the adsorbing efficacy of the generally larger portion of adsorbent used to purify the remaining portion of the stream

  18. The Barents Sea, distribution and fate of radioactive contaminants

    International Nuclear Information System (INIS)

    Foeyn, L.; Heldal, H.E.; Svaeren, I.

    1999-01-01

    Possible contamination in the marine food webs of the Barents Sea may be a problem for a rational harvest of the area. Radioactive contamination has in this context a special public impact as even traces of radioactivity seems to be considered by the public to be a real danger. It is therefor of special importance, from a regulatory and fisheries point of view, to accumulate knowledge of the behaviour of radioactive elements in the marine ecosystems of the Barents Sea in order to place this contamination in proper and realistic proportions

  19. Process for reducing radioactive contamination in waste product gypsum

    International Nuclear Information System (INIS)

    Lange, P.H. Jr.

    1979-01-01

    A process is described for reducing the radioactive contamination in waste product gypsum in which waste product gypsum is reacted with a dilute sulfuric acid containing barium sulfate to form an acid slurry at an elevated temperature, the slurry is preferably cooled, the acid component is separated from the solid, and the resulting solid is separated into a fine fraction and a coarse fraction. The fine fraction predominates in barium sulfate and radioactive contamination. The coarse fraction predominates in a purified gypsum product of reduced radioactive contamination

  20. Assessment of low levels of radioactive contamination

    International Nuclear Information System (INIS)

    Gray, P.W.

    1988-01-01

    This report describes a general methodology for the verification and clearance of sites contaminated with radioactive materials; general expressions for the risk or health detriment are derived. Techniques are developed, using Bayesian decision theory, to optimize the resources allocated to a site monitoring procedure, and to construct the probability distribution of the spatial distribution of specific activity within a site. A technique is also developed to determine the probability that a localized source of specified characteristics will not be detected by the monitoring procedure employed. The application of these techniques is illustrated by means of simple examples. This report confirms that a very large number of measurements are needed if a source of localized activity is to be detected with a high probability, and demonstrates how prior information about past radiological practices might be used to increase the probability of detection. Proposals are made for a programme of research to determine whether or not representative sites can be verified using current measuring techniques. (author)

  1. Lichens as indicators of radioactive contamination

    International Nuclear Information System (INIS)

    Biarzov, L.

    1993-01-01

    Samples of lichens were investigated, collected in 1987 in the Eastern Urals and in 1988 in the vicinity of Chernobyl. Data are given on the size of thalli of epiphytic lichens from trunks of pine in the Chernobyl area, and on the beta activity in epiphytic lichens in the birch forests of the Urals 30 years after the Kyshtym accident, as well as concentrations of 40 K, 106 Ru, 134 Cs, 137 Cs, and 144 Ce in lichen thalli and the bark of pine tree, taken at 5 locations in the vicinity of Chernobyl 1000 days after the accident. Also given are cross-ratios of radioactivity of 106 Ru, 134 Cs, 137 Cs, and 144 Ce in lichen thalli and in the bark of pine trees. The results indicate that the activity of radionuclides in lichen thalli make a fairly reliable indicator of relative differences between the investigated areas in terms of the level of surface contamination and qualitative composition of the involved radionuclides. (J.B.) 4 tabs., 15 refs

  2. Radioactive standards and calibration methods for contamination monitoring instruments

    Energy Technology Data Exchange (ETDEWEB)

    Yoshida, Makoto [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    1997-06-01

    Contamination monitoring in the facilities for handling unsealed radioactive materials is one of the most important procedures for radiation protection as well as radiation dose monitoring. For implementation of the proper contamination monitoring, radiation measuring instruments should not only be suitable to the purpose of monitoring, but also be well calibrated for the objective qualities of measurement. In the calibration of contamination monitoring instruments, quality reference activities need to be used. They are supplied in different such as extended sources, radioactive solutions or radioactive gases. These reference activities must be traceable to the national standards or equivalent standards. On the other hand, the appropriate calibration methods must be applied for each type of contamination monitoring instruments. In this paper, the concepts of calibration for contamination monitoring instruments, reference sources, determination methods of reference quantities and practical calibration methods of contamination monitoring instruments, including the procedures carried out in Japan Atomic Energy Research Institute and some relevant experimental data. (G.K.)

  3. Method of melting decontamination of radioactive contaminated metals

    International Nuclear Information System (INIS)

    Uda, Tatsuhiko; Miura, Noboru; Tsuchiya, Hiroyuki.

    1984-01-01

    Purpose: To improve the transfer efficiency of radioactive materials into slags. Method: Contaminated metals are melt with adding slagging agent in order to transfer the radioactive materials into the slag, where the slagging agent holds less free energy than that of metal oxides contaminated with radioactive materials in order to promote the transfer of the contaminated materials into the slag layer. This effect can also be attained on metals or alloys other than iron contaminated with radioactive materials. In the case of alloy, the slagging agent is to containing such metal oxide that free energy is less than that of the oxide of metal being the main ingredient element of the alloy. The decontamination effect can further be improved by containing halogenide such as calcium fluoride together with the metal oxide into the slagging agent. (Ikeda, J.)

  4. Radioactive contamination of aquatic media and organisms; La contamination radioactive des milieux et des organismes aquatiques

    Energy Technology Data Exchange (ETDEWEB)

    Fontaine, Y [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

    1960-07-01

    After a brief account of the radioactive wastes produced by peaceful or military uses of Atomic Industry, the author first describes a series of observations carried out 'in the field' on the extent of contamination in aquatic organisms with respect to that of the medium. The experimental studies are then analysed, with reference both to the radioisotope metabolism and to the factors and types of contamination of aquatic organisms by wastes from atomic industry. A precise experimental project is presented at the end of the paper, including almost 300 references. (author) [French] Apres une courte etude des dechets radioactifs produits par les utilisations pacifiques ou militaires de l'Industrie Atomique, l'auteur fait etat d'abord des observations effectuees 'sur le terrain' concernant l'extension de la contamination des organismes aquatiques en rapport avec celle du milieu. L'auteur analyse ensuite les etudes experimentales se rapportant aussi bien au metabolisme des radioisotopes qu'aux facteurs et aux modalites de la contamination des organismes aquatiques par les dechets de l'industrie atomique. Un projet de travail experimental precis est presente a la fin de cette revue qui comporte pres de 300 references bibliographiques. (auteur)

  5. Radioactive contamination of aquatic media and organisms; La contamination radioactive des milieux et des organismes aquatiques

    Energy Technology Data Exchange (ETDEWEB)

    Fontaine, Y. [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

    1960-07-01

    After a brief account of the radioactive wastes produced by peaceful or military uses of Atomic Industry, the author first describes a series of observations carried out 'in the field' on the extent of contamination in aquatic organisms with respect to that of the medium. The experimental studies are then analysed, with reference both to the radioisotope metabolism and to the factors and types of contamination of aquatic organisms by wastes from atomic industry. A precise experimental project is presented at the end of the paper, including almost 300 references. (author) [French] Apres une courte etude des dechets radioactifs produits par les utilisations pacifiques ou militaires de l'Industrie Atomique, l'auteur fait etat d'abord des observations effectuees 'sur le terrain' concernant l'extension de la contamination des organismes aquatiques en rapport avec celle du milieu. L'auteur analyse ensuite les etudes experimentales se rapportant aussi bien au metabolisme des radioisotopes qu'aux facteurs et aux modalites de la contamination des organismes aquatiques par les dechets de l'industrie atomique. Un projet de travail experimental precis est presente a la fin de cette revue qui comporte pres de 300 references bibliographiques. (auteur)

  6. Radioactive contamination of food and the intake by man

    International Nuclear Information System (INIS)

    Frissel, M.J.; Blaauboer, R.O.; Koester, H.W.; Leenhouts, H.P.; Stoutjesdijk, J.F.; Vaas, L.H.

    1989-01-01

    This paper describes the different pathways by which food is contaminated after a release of radionuclides into the environment. Equations to calculate the contamination level, as well as the most important parameters used in these equations, are included. Thereupon is explained how the radiation dose can be calculated from the intake of radioactivity. The principles which are used to derive criteria for the amounts of radioactivity which are allowed in food are described. (author)

  7. Investigation of radioactive contamination at non-radioactive drains of the Tsuruga Nuclear Power Station

    International Nuclear Information System (INIS)

    Koide, Hiroaki; Imanaka, Tetsuji; Ebisawa, Toru; Kawano, Shinji; Kobayashi, Keiji.

    1982-05-01

    In April, 1981, it was disclosed that a drainage area at the Tsuruga Nuclear Power Station was so much contaminated with radioactivites. Although Ministry of International Trade and Industry (MITI) officially provided an explanation of a process that resulted in the contamination, many problems remain unsolved on account of insufficient and limited investigations. The authors collected mud samples from contaminated manholes and examined radioactivities in them through the measurement of #betta#- and #betta#-spectra. Chemical separation of the samples was carried out in order to obtain precise concentration of radioactive cesium. Results are as follows: i) the concentration of radioactivities does not show monotonous decrease along the stream line but an anomalous peak at downstream manholes, ii) at the manhole specified No. 6 located rather downstream, 137 Cs concentration is significantly high and the composition of radioactive nuclides is quite different from that in the other manholes, and iii) additional radioactive contamination was observed in other manholes of non-radioactive drains which would not be influenced by the accident explained by MITI. Our present work has provided much more data than by MITI and made it clear that the overall data cnnot be consistent with the simple MITI explanation; a single radioactive release accident caused the disclosed contamination. It is concluded that non-radioactive water drains at the Tsuruga Nuclear Power Station had been under continual contamination. (author)

  8. Status of outdoor radioactive contamination at the Hanford Site

    International Nuclear Information System (INIS)

    McKinney, S.M.; Markes, B.M.

    1994-12-01

    This document summarizes the status of outdoor radioactive contamination near Hanford Site facilities and disposal sites. It defines the nature and areal extend of the radioactively contaminated areas and describes the historical, ongoing, and planned radiological monitoring and control activities. Radioactive waste has been disposed of to the soil column since shortly after the reactors and production facilities began operating. Radioactive liquid wastes were placed directly into the ground via liquid discharges to cribs, ponds, ditches, and reverse wells. Solid wastes were placed in trenches, burial vaults, and caissons. Although the Hanford Site covers 1,450 km 2 , the radioactively contaminated area is only about 36 km 2 or 2.5% of the original site. Over time, contamination has migrated from some of the waste management sites through various vectors (e.g., burrowing animals, deep-rooted vegetation, erosion, containment system failure) or has been deposited to the surface soil via spills and unplanned releases (e.g., line leaks/breaks, tank leaks, and stack discharges) and created areas of outdoor radioactivity both on and below the surface. Currently 26 km 2 are posted as surface contamination and 10 km 2 are posted as underground contamination

  9. Economics and risks of recycling radioactively contaminated concrete

    International Nuclear Information System (INIS)

    Parker, F.L.; Ayers, K.W.

    1997-01-01

    As Decontamination and Decommissioning activities proceed within the DOE complex, tremendous volumes of both radioactively contaminated and non-contaminated concrete will be processed for disposal. Current practice is to decontaminate the concrete, dispose of the contamination at LLW facilities and ship the concrete rubble to C ampersand D landfills for disposal. This study evaluates the economic, health and safety, legal, and social aspects of recycling radioactively contaminated concrete. Probabilistic models were used to estimate costs and risks. The model indicates that the radioactively contaminated concrete can be recycled at the same or lower cost than current or alternative practices. The risks associated with recycling were consistently less than or equal to the other alternatives considered

  10. Cost of the radioactive residues of nuclear power

    International Nuclear Information System (INIS)

    1986-06-01

    The calculation of cost for the management and final storage of spent nuclear fuel and radioactive waste is presented. The continuing Research and Development activities are judged to render simplified designs. The existing and planned systems and and plans are as follows: - transport system for radioactive residues - central intermediate storage of spent fuel, CLAB - processing of spent fuel - final storing of long-lived waste - final storing of reactor waste and decommissioning waste, SFR. The total future cost of the Swedish waste management is calculated to be 39 billion SEK from 1987 and 60 years onwards. 5.3 billion SEK have been spent up to the year 1986. (G.B.)

  11. Radioactive waste management for a radiologically contaminated hospitalized patient

    International Nuclear Information System (INIS)

    Pina Jomir, G.; Michel, X.; Lecompte, Y.; Chianea, N.; Cazoulat, A.

    2015-01-01

    Radioactive waste management in the post-accidental phase following caring for a radiologically contaminated patient in a hospital decontamination facility must be anticipated at a local level to be truly efficient, as the volume of waste could be substantial. This management must comply with the principles set out for radioactive as well as medical waste. The first step involves identification of radiologically contaminated waste based on radioactivity measurement for volume reduction. Then, the management depends on the longest radioactive half-life of contaminative radionuclides. For a half-life inferior to 100 days, wastes are stored for their radioactivity to decay for at least 10 periods before disposal like conventional medical waste. Long-lived radioactive waste management implies treatment of liquid waste and special handling for sorting and packaging before final elimination at the French National Agency for Radioactive Waste Management (ANDRA). Following this, highly specialized waste management skills, financial responsibility issues and detention of non-medical radioactive sources are questions raised by hospital radioactive waste management in the post-accidental phase. (authors)

  12. Removal and treatment of radioactive, organochlorine, and heavy metal contaminants from solid surfaces

    International Nuclear Information System (INIS)

    Grieco, S.A.; Neubauer, E.D.

    1996-01-01

    The U.S. Department of Energy (DOE) is defining decontamination and decommissioning (D ampersand D) obligations at its sites. Current D ampersand D activities are generally labor intensive, use chemical reagents that are difficult to treat, and may expose workers to radioactive and hazardous chemicals. Therefore, new technologies are desired that minimize waste, allow much of the decommissioned materials to be reused rather than disposed of as waste, and produce wastes that will meet disposal criteria. The O'Brien ampersand Gere companies tested a scouring decontamination system on concrete and steel surfaces contaminated with radioactive and hazardous wastes under the sponsorship of Martin Marietta Energy Systems, Inc. (MMES) at DOE's K-25 former gaseous diffusion plant in Oak Ridge, Tennessee. The scouring system removes fixed radioactive and hazardous contamination yet leaves the surface intact. Blasting residuals are treated using physical/chemical processes. Bench- and pilot-scale testing of the system was conducted on surfaces contaminated with uranium, technetium, heavy metals, and PCBs. Areas of concrete and metal surfaces were blasted. Residuals were dissolved in tap water and treated for radioactive, hazardous, and organochlorine constituents. The treatment system comprised pH adjustment, aeration, solids settling, filtration, carbon adsorption, and ion exchange. This system produced treated water and residual solid waste. Testing demonstrated that the system is capable of removing greater than 95% of radioactive and PCB surface contamination to below DOE's unrestricted use release limits; aqueous radionuclides, heavy metals, and PCBs were below DOE and USEPA treatment objectives after treatment. Waste residuals volume was decreased by 71 %. Preliminary analyses suggest that this system provides significant waste volume reduction and is more economical than alternative surface decontamination techniques that are commercially available or under development

  13. Airborne radioactive contamination following aerosol ventilation studies

    International Nuclear Information System (INIS)

    Mackie, A.; Hart, G.C.; Ibbett, D.A.; Whitehead, R.J.S.

    1994-01-01

    Lung aerosol ventilation studies may be accompanied by airborne contamination, with subsequent surface contamination. Airborne contamination has been measured prior to, during and following 59 consecutive 99 Tc m -diethylenetriamine pentaacetate (DTPA) aerosol studies using a personal air sampler. Airborne contamination ranging between 0 and 20 330 kBq m -3 has been measured. Airborne contamination increases with degree of patient breathing difficulty. The effective dose equivalent (EDE) to staff from ingested activity has been calculated to be 0.3 μSv per study. This figure is supported by data from gamma camera images of a contaminated staff member. However, surface contamination measurements reveal that 60% of studies exceed maximum permissible contamination limits for the hands; 16% of studies exceed limits for controlled area surfaces. (author)

  14. Control of radioactive contamination of food in the country Somogy

    International Nuclear Information System (INIS)

    Varga, E.; Viragh, I.

    1980-01-01

    The radioactive contamination of spinach, sorrel, lettuce, animal bones, milk and fish was determined in the period 1961-1978. Peak values were measured in 1963 and 1976. The contamination of plants reached higher levels, however, it did not exceed 25 pCi per g dry weight. (L.E.)

  15. Radioactive contamination in Arctic - present situation and future challenges

    International Nuclear Information System (INIS)

    Strand, Per

    2002-01-01

    There is currently a focus on radioactivity and the Arctic region. The reason for this is probably the high number of nuclear sources in parts of the Arctic and the vulnerability of Arctic systems to radioactive contamination. The Arctic environment is also perceived as a wilderness and the need for the protection of this wilderness against contamination is great. In the last decade information has also been released concerning the nuclear situation which has caused concern in many countries. Due to such concerns, the International Arctic Environmental Protection Strategy (IAEPS) was launched in 1991 and the Arctic Monitoring and Assessment Programme (AMAP) was established. AMAP is undertaking an assessment of the radioactive contamination of the Arctic and its radiological consequences. In 1996 IAEPS became part of the Arctic Council. AMAP presented one main report in 1997 and another in 1998. There are also several other national, bilateral and international programmes in existence which deal with this issue. This paper summarises some of current knowledge about sources of radioactive contamination, vulnerability, exposure of man, and potential sources for radioactive contamination within Arctic and some views on the future needs for work concerning radioactivity in Arctic. (au)

  16. Control System Radioactive Contamination in Food Samples in Poland

    International Nuclear Information System (INIS)

    Grabowski, D.; Kurowski, W.; Muszynski, W.; Rubel, B.; Smagala, G.; Swietochowska, J.

    2001-01-01

    Full text: The analyses of the level of radioactive contamination in food samples are carried out by the Service for Measurements of Radioactive Contamination (SMRC) in Poland. The Service was brought into existence in 1961. The Service comprises of a network of measurement stations and the Centre of Radioactive Contamination Measurements (CRCM). The duty of the Centre is being executed by the Central Laboratory for Radiological Protection (CLRP). The uniform methods of sampling are used in measurement stations. All important foodstuff: milk, meat, vegetables, fruit, cereals are controlled in the Service stations. The radiochemical and spectrometric methods are used to determine the activity of radioactive isotopes. The standard equipment of the measurement station is the measurement system type SAPOS-90 and multichannel analyser with scintillation or germanium detector. The structure of the Service, kinds of samples tested by each station, program of sampling in normal and during accident situation are presented in this paper. (author)

  17. Method of electrolytic decontamination of contaminated metal materials for radioactivity

    International Nuclear Information System (INIS)

    Harada, Yoshio; Ishibashi, Masaru; Matsumoto, Hiroyo.

    1985-01-01

    Purpose: To electrolytically eliminate radioactive materials from metal materials contaminated with radioactive materials, as well as efficiently remove metal ions leached out in an electrolyte. Method: In the case of anodic dissolution of metal materials contaminated with radioactivity in an electrolyte to eliminate radioactive contaminating materials on the surface of the metal materials, a portion of an electrolytic cell is defined with partition membranes capable of permeating metal ions therethrough. A cathode connected to a different power source is disposed to the inside of the partition membranes and fine particle of metals are suspended and floated in the electrolyte. By supplying an electric current between an insoluble anode disposed outside of the partition membranes and the cathode, metal ions permeating from the outside of the partition membranes are deposited on the fine metal particles. Accordingly, since metal ions in the electrolyte are removed, the electrolyte can always be kept clean. (Yoshihara, H.)

  18. Auburn Steel Company radioactive contamination incident

    International Nuclear Information System (INIS)

    Bradley, F.J.; Cabasino, L.; Kelly, R.; Awai, A.; Kasyk, G.

    1986-04-01

    On February 21, 1983, workers at the Auburn Steel Company, Auburn, New York discovered that about 120 tons of steel poured that day had become contaminated with 60 Co. In addition to the steel, the air cleaning system and portions of the mill used in casting the steel were contaminated. Approximately 25 curies of 60 Co were involved. Decontamination and disposal of the contamination cost in excess of $2,200,000. This report details the discovery of the contamination, decontamination of the plant and disposal of the contamination

  19. Thule-2003 - Investigation of radioactive contamination

    Energy Technology Data Exchange (ETDEWEB)

    Nielsen, Sven P.; Roos, P.

    2006-05-15

    Analyses of marine and terrestrial samples collected in August 2003 from Bylot Sound at Thule, Northwest Greenland, show that plutonium from nuclear weapons in the American B52 plane, which crashed on the sea ice in January 1968, persists in the environment. The highest concentrations of plutonium are found in the marine sediments under the location where the plane crashed. The distribution of plutonium in the marine sediment is very inhomogeneous and associated with hot particles with activities found up to 1500 Bq {sup 239,240}Pu. Sediment samples collected in Wolstenholme Fjord north of the accident site show plutonium concentrations, which illustrates the redistribution of plutonium after the accident. The total plutonium inventory in the sediments has been assessed based on systematic analyses considering hot particles. The inventory of {sup 239,240}Pu in the sediments within a distance of 17 km from the point of impact of the B52 plane is estimated at 2.9 TBq (1 kg). Earlier estimates of the inventory were approximately 1.4 TBq {sup 239,240}Pu. Seawater and seaweed samples show increased concentrations of plutonium in Bylot Sound. The increased concentrations are due to resuspension of plutonium-containing particles from the seabed and transport further away from the area. Plutonium concentrations in seawater, seaweed and benthic animals in Bylot Sound are low but clearly above background levels. All soil samples collected from Narssarssuk show accident plutonium with levels above background. Plutonium is very inhomogeneously distributed and associated with particles in the surface layers. Hot particles were found in soil with activities up to 150 Bq {sup 239,240}Pu. Plutonium in the marine environment at Thule presents an insignificant risk to man. Most plutonium remains in the seabed under Bylot Sound far from man under relatively stable conditions and concentrations of plutonium in seawater and animals are low. However, the plutonium contamination of

  20. Thule-2003 - Investigation of radioactive contamination

    International Nuclear Information System (INIS)

    Nielsen, Sven P.; Roos, P.

    2006-05-01

    Analyses of marine and terrestrial samples collected in August 2003 from Bylot Sound at Thule, Northwest Greenland, show that plutonium from nuclear weapons in the American B52 plane, which crashed on the sea ice in January 1968, persists in the environment. The highest concentrations of plutonium are found in the marine sediments under the location where the plane crashed. The distribution of plutonium in the marine sediment is very inhomogeneous and associated with hot particles with activities found up to 1500 Bq 239,240 Pu. Sediment samples collected in Wolstenholme Fjord north of the accident site show plutonium concentrations, which illustrates the redistribution of plutonium after the accident. The total plutonium inventory in the sediments has been assessed based on systematic analyses considering hot particles. The inventory of 239,240 Pu in the sediments within a distance of 17 km from the point of impact of the B52 plane is estimated at 2.9 TBq (1 kg). Earlier estimates of the inventory were approximately 1.4 TBq 239,240 Pu. Seawater and seaweed samples show increased concentrations of plutonium in Bylot Sound. The increased concentrations are due to resuspension of plutonium-containing particles from the seabed and transport further away from the area. Plutonium concentrations in seawater, seaweed and benthic animals in Bylot Sound are low but clearly above background levels. All soil samples collected from Narssarssuk show accident plutonium with levels above background. Plutonium is very inhomogeneously distributed and associated with particles in the surface layers. Hot particles were found in soil with activities up to 150 Bq 239,240 Pu. Plutonium in the marine environment at Thule presents an insignificant risk to man. Most plutonium remains in the seabed under Bylot Sound far from man under relatively stable conditions and concentrations of plutonium in seawater and animals are low. However, the plutonium contamination of surface soil at

  1. Transboundary Movement of Radioactively Contaminated Scrap Metal - Lessons Learned

    Energy Technology Data Exchange (ETDEWEB)

    Nizamska, M., E-mail: m.nimzamska@bnra.bg [Emergency Planning and Preparedness Division, Bulgarian Nuclear Regulatory Agency, Sofia (Bulgaria)

    2011-07-15

    Starting in 1989, Bulgaria has undergone a comprehensive transformation of its economy and social conditions. Part of this process is related to the intensive privatization that started in 2001. This privatization included facilities, as well as sites that use radioactive material for different applications - industry, medicine, agriculture, science, etc. The rapid change of property ownership and, in some cases, the resulting bankruptcy, has caused difficulties in tracing and identifying radioactive sources and materials and a deterioration of the system of safety, physical protection, etc. of radioactive material. In some cases, radioactive sources were stolen because of the value of their protective containers and sold for scrap metal. This led to the occurrence of different types of radiation incidents, mainly related to the discovery of radioactive sources in scrap metal. The consequences of these incidents include the risk of radiation exposure of the workers at scrap metal yards or reprocessing facilities and of members of the public and, in addition, radioactive contamination of the environment. The Bulgarian Nuclear Regulatory Agency (BNRA) has been responding to these incidents and has carried out a series of measures to improve the control over materials (e.g. activated or surface contaminated materials) and radioactive sources and to strengthen the preventive, monitoring, emergency preparedness and mitigating measures at facility, national and transboundary levels. This paper presents an analysis of the lessons learned by the BNRA and of the control of the transboundary movement of radioactively contaminated scrap metal through the territory of Bulgaria. (author)

  2. Development of irradiation technique on controlling food contamination residue

    International Nuclear Information System (INIS)

    Liu Bin; Xiong Shanbai; Xiong Guangquan; Cheng Wei; Chen Yuxia; Liao Tao; Li Xin; Lin Ruotai

    2010-01-01

    The current state of the researches of irradiation technology on controlling food mycotoxin, pesticide, veterinary drugs and fishery drugs residue was summarized. And the degradation rate, mechanism, products and toxicities of food contamination were expatiated. The free radical from irradiation attack the site of weaker bond, and the less or more toxic substances were produced, which lead to the degradation of the food contamination. The limitations and future application of irradiation technique on controlling food contamination were also analyzed. (authors)

  3. Method of preventing contaminations in radioactive material handling facilities

    International Nuclear Information System (INIS)

    Inoue, Shunji.

    1986-01-01

    Purpose: To prevent the contamination on the floor surface of working places by laying polyvinyl butyral sheets over the floor surface, replacing when the sheets are contaminated, followed by burning. Method: Polyvinyl butyral sheets comprising 50 - 70 mol% of butyral component are laid in a radioactive material handling facility, radioactive materials are handled on the polyvinyl butyral sheets and the sheets are replaced when contaminated. The polyvinyl butyral sheets used contain 62 - 68 mol% of butyral component and has 0.03 - 0.2 mm thickness. The contaminated sheets are subjected to burning processing. This can surely collect radioactive materials and the sheets have favorable burnability, releasing no corrosive or deleterious gases. In addition, they are inexpensive and give no hindrance to the workers walking. (Takahashi, M.)

  4. Some problems of risk assessment in cases of environmental radioactive and chemical contamination in regions of the Ural radioactive trail

    International Nuclear Information System (INIS)

    Kryshev, I.I.; Isaeva, L.N.; Sazykina, T.G.

    1995-01-01

    A methodology of risk assessment if being developed to permit the analysis of possible consequences of radioactive and chemical environment contamination on the territory of the Urals radioactive trail. The assessment of hazards from radioactive contamination of the Techa river (Muslyumovo) has been carried out. A comparison of radioactive and chemical risks for the population of Kasli has been made

  5. The radioactive contamination level in Croatia by means of radioactive rainwaters, caused by the accident in NPP 'Lenin'

    International Nuclear Information System (INIS)

    Barishicj, D.; Koshuticj, K.; Kvastek, K.; Lulicj, S.; Tuta, J.; Vertachnik, A.; Vrhovac, A.

    1987-01-01

    In this paper, the radioactive contamination level in Croatia by means of radioactive rainwaters, caused by the accident in NPP 'Lenin', has been described. The results represent the sum of measured and evaluated data, the map of the radioactive contamination in Croatia caused by radioactive rainwaters between April, 28 to May, 20 1986 has been constructed. (author) 3 tabs.; 5 figs

  6. Substantiation of the permissible radioactive contamination of working clothes

    International Nuclear Information System (INIS)

    Shcherbakov, V.L.; Korostin, A.S.

    1977-01-01

    A permissible level of working clothes contamination was determined on the base of the main migration routes of radioactive contaminants: permeation directly through the clothes into subclothes space on skin surface, emission into the air with amount of contaminants subsequently got by the organism of a working person through inhalation as well as transfer in the process of contacting of contaminated working clothes and surfaces of premises equipment, working person hands with amount of contaminants posteriorly got by the organism by alimentary or inhalation ways. Using the experimental and literature data available the permissible levels of working clothes contamination for the mentioned migration routes of radioactive materials have been calculated. According to the data obtained the permissible levels of working clothes contamination must not exceed 4 alpha-part/(cm 2 xmin) for contamination with high-tonic isotopes, 20 alpha-part./(cm 2 xmin) with other alpha-detine isotopes, 1000 beta-part./(cm 2 xmin) with beta-active ones. The permissible level of contamination of additional materials of the individual protection in the case of their contamination with high-tonic alpha-actine isotopes must not exceed 50 alpha-part./(cm 2 xmin), 200 alpha-part./(cm 2 xmin) for contamination th other alpha-active isotopes and 400 beta-part./(cm 2 xmin) with beta-active isotopes

  7. Earthworm tolerance to residual agricultural pesticide contamination

    DEFF Research Database (Denmark)

    Givaudan, Nicolas; Binet, Françoise; Le Bot, Barbara

    2014-01-01

    of soluble glutathione-S-transferases (sGST) and catalase increased with soil pesticide contamination in A. caliginosa. Pesticide stress was reflected in depletion of energy reserves in A. chlorotica. Acute exposure of pre-adapted and naïve A. caliginosa to pesticides (fungicide Opus ®, 0.1 μg active...

  8. Bonding of radioactive contamination. IV. Effect of surface finish

    International Nuclear Information System (INIS)

    Rankin, W.N.

    1983-01-01

    The mechanisms by which radioactive contamination would be bonded to a DWPF canister are being investigated. Previous investigations in this series have examined the effects of temperature, oxidation before contamination, and atmosphere composition control on the bonding of contamination. This memorandum describes the results of tests to determine the effect of special surface finishes on the bonding of contamination to waste glass canisters. Surface pretreatments which produce smoother canister surfaces actually cause radioactive contamination to be more tightly bonded to the metal surface than on an untreated surface. Based on the results of these tests it is recommended that the canister surface finish be specified as having a bright cold rolled mill finish equivalent to ASTM No. 2B. 7 references, 3 figures, 3 tables

  9. Water in the March river radioactively contaminated

    International Nuclear Information System (INIS)

    Englander, A.G.

    1990-01-01

    A curve of the tritium contamination of the March river measured in Austria from 1976 to 1989 is shown. The conjecture is put forward that this contamination is caused by the Dukovani power plant in the neighbouring CSFR. Further measurements are called for

  10. Release behavior of triazine residues in stabilised contaminated soils

    International Nuclear Information System (INIS)

    Ying, G.G.; Kookana, R.S.; Mallavarpu, M.

    2005-01-01

    This paper reports the release behavior of two triazines (atrazine and simazine) in stabilised soils from a pesticide-contaminated site in South Australia. The soils were contaminated with a range of pesticides, especially with triazine herbicides. With multiple extractions of each soil sample with deionised water (eight in total), 15% of atrazine and 4% of simazine residues were recovered, resulting in very high concentrations of the two herbicides in leachate. The presence of small fractions of surfactants was found to further enhance the release of the residues. Methanol content up to 10% did not substantially influence the concentration of simazine and atrazine released. The study demonstrated that while the stabilisation of contaminated soil with particulate activated carbon (5%) and cement mix (15%) was effective in locking the residues of some pesticides, it failed to immobilise triazine herbicides residues completely. Given the higher water solubility of these herbicides than other compounds more effective strategies to immobilise their residues is needed. - Stabilisation of contaminated soil with a mix of activated carbon and cement may fail to immobilise some contaminants like triazines

  11. Derivation of guidelines for uranium residual radioactive material in soil at the Colonie Site, Colonie, New York

    International Nuclear Information System (INIS)

    Dunning, D.

    1996-05-01

    Residual radioactive material guidelines for uranium in soil were derived for the Colonie site located in Colonie, New York. This site has been designated for remedial action under the Formerly Utilized Sites Remedial Action Program (FUSRAP) of the U.S. Department of Energy (DOE). The site became contaminated with radioactive material as a result of operations conducted by National Lead (NL) Industries from 1958 to 1984; these activities included brass foundry operations, electroplating of metal products, machining of various components using depleted uranium, and limited work with small amounts of enriched uranium and thorium. The Colonie site comprises the former NL Industries property, now designated the Colonie Interim Storage Site (CISS), and 56 vicinity properties contaminated by fallout from airborne emissions; 53 of the vicinity properties were previously remediated between 1984 and 1988. In 1984, DOE accepted ownership of the CISS property from NL Industries. Residual radioactive material guidelines for individual radionuclides and total uranium were derived on the basis of the requirement that the 50-year committed effective dose equivalent to a hypothetical individual who lives or works in the immediate vicinity of the site should not exceed a dose of 30 mrem/yr following remedial action for the current use and likely future use scenarios or a dose of 100 mrem/yr for less likely future use scenarios. The DOE residual radioactive material guideline computer code, RESRAD, was used in this evaluation; RESRAD implements the methodology described in the DOE manual for establishing residual radioactive material guidelines

  12. Bonding of radioactive contamination. III. Auger electron spectroscopic investigation

    International Nuclear Information System (INIS)

    Rankin, W.N.; Whitkop, P.G.

    1983-01-01

    The mechanisms by which radioactive contamination would be bonded to a DWPF canister surface are being investigated. Tests with low pressure water and air-injected water decontamination of radioactive specimens showed that bonding of contamination increases rapidly with postoxidation temperature. Even with the least severe temperature conditions expected on the waste glass canister, bonding is so great that decontamination cannot be affected by water-only techniques. A preoxidation film increased rather than decreased bonding. This memorandum describes detailed surface analyses of coupons simulating DWPF canister surfaces. Based on this examination we conclude: contamination will be dispersed throughout the oxide film on DWPF canisters. Contamination is concentrated at the surface, decreasing farther into the oxide film; some samples contain sludge contamination at the steel/oxide interface. This was not the case for semi-volatile (Cs 2 O) contamination; in samples with contamination at the steel/oxide interface, at least 80% of the contamination is usually in the oxide layer; no difference in contamination dispersion between preoxidized and non-preoxidized samples was found; and postoxidation atmosphere had no effect on the contamination dispersion within the oxide layer. 6 references, 9 figures

  13. Process for cleaning radioactively contaminated metal surfaces

    International Nuclear Information System (INIS)

    Mihram, R.G.; Snyder, G.A.

    1975-01-01

    A process is described for removing radioactive scale from a ferrous metal surface, including the steps of initially preconditioning the surface by contacting it with an oxidizing solution (such as an aqueous solution of an alkali metal permanganate or hydrogen peroxide), then, after removal or decomposition of the oxidizing solution, the metallic surface is contacted with a cleaning solution which is a mixture of a mineral acid and a complexing agent (such as sulfuric acid and oxalic acid), and which preferably contains a corrosion inhibitor. A final step in the process is the treatment of the spent cleaning solution containing radioactive waste materials in solution by adding a reagent selected from the group consisting of calcium hydroxide or potassium permanganate and an alkali metal hydroxide to thereby form easily recovered metallic compounds containing substantially all of the dissolved metals and radioactivity. (auth)

  14. Radioactive elements found in plants contaminated by radioactive rain

    Energy Technology Data Exchange (ETDEWEB)

    Tanidazawa, M; Ishihara, T

    1954-01-01

    Ashes obtained from contaminated trifolium repens, astragalus sinicus, and rumex japonicus were studied. The precipitate obtained by treating the acidic solution of the ash with H/sub 2/S followed by Fe/sup + +/ in the presence of NH/sub 3/ and NH/sub 4/Cl contained Y, Sr, and the rare earth elements.

  15. Development of plastic scintillator based food radioactivity contamination monitoring system

    International Nuclear Information System (INIS)

    Parihar, A.; Sahani, R.M.; Mahala, V.K.; Vaijapurkar, S.G.

    2016-01-01

    Radioactivity is naturally present in soil, water and food stuffs. Food can be contaminated after discharge of radioactivity into the environment from industries that concentrate natural radionuclide and from civil or military nuclear operations. The contamination can be in three ways; by direct deposition, through the food chain and induced radioactivity due to exposure of high neutron flux. The health effects on human depend on the type of radionuclide and the length of time people are exposed to it. The studies of fission product behaviour in the food chain have revealed radionuclide Strontium-90, Caesium 137 and Iodine-131 are of major concern. Plastic scintillator is already developed indigenously at Defence Laboratory, Jodhpur. Efforts has been made to develop a portable field instrument using plastic scintillator for assessment of beta ( 90 Sr) and gamma ( 137 Cs and 131 I) radioactivity in food

  16. Investigation to radioactive contamination of pool water in IMEF

    International Nuclear Information System (INIS)

    Song, Ung Sup; Jung, Yang Hong; Lee, J. H.; Lee, H. K.

    2003-06-01

    The pool (3x6x10) in irradiated materials examination facility is usually used for the purpose of taking the specimen out of cask loaded into the pool, and carrying in/out the specimen to/ from the hot cell. Always, it must be cared for the water into the pool to be fine condition because all operation are worked with the naked eye during taking an irradiated materials out of the cask and plunging them in the bucket-elevator. In the aspects of the radioactive remained substances in the water must be controlled so that the amount of substances to be lower than the standard amount prescribed by RCA Korea Activity in a part of radioactive contamination control. In consequence, an expertness of status and a practical use of skill make possible the prevention of radioactive material's diffusion or the radioactive contamination of pool water and safety work

  17. Radioactive contamination in environment and food in Poland in 1992

    International Nuclear Information System (INIS)

    Grabowski, D.; Muszynski, W.; Petrykowska, M.; Rubel, B.; Smagala, G.; Wilgos, J.

    1993-01-01

    The level analysis of the level of radioactive contamination in environment and food samples was carried out in Poland in 1992. The results were compared to the data from 1985-1991 period. Since the Chernobyl accident gradual decrease of contamination level has been stated. The gamma dose rate and the contamination of air, fallout, tap and surface water were at the level of 1985. Still higher contamination level of cesium isotopes in soil has been reported and as a consequence food contamination was higher particularly the animal food. Actually, the source of additional dose is ingestion of artificial isotopes with food as a result of food contamination. The average effective dose equivalent, due to the contaminated food consumption, was estimated at the level 15 μSv for a Pole in 1992. (author). 13 refs, 6 figs, 20 tabs

  18. Derivation of residual radioactive material guidelines for the Laboratory for Energy-Related Health Research site

    International Nuclear Information System (INIS)

    Chapman, T.E.

    1993-11-01

    Residual radioactive material guidelines were derived for the Laboratory for Energy-Related Health Research (LEHR) Environmental Restoration (ER) site in Davis, California. The guideline derivation was based on a dose limit of 100 mrem/yr. The US Department of Energy (DOE) residual radioactive material guideline computer code was used in this evaluation. This code implements the methodology described in the DOE manual for implementing residual radioactive material guidelines. Three potential site utilization scenarios were considered with the assumption that following ER action, the site will be used without radiological restrictions. The defined scenarios vary with regard to use of the site, time spent at the site, and sources of food consumed. The results of the evaluation indicate that the basic dose limit of 100 mrem/yr will not be exceeded, provided that the soil concentrations of these radionuclides at the LEHR site do not exceed the scenario-specific values calculated by this study. Except for the extent of the contaminated zone (which is very conservative), assumptions used are as site-specific as possible, given available information. The derived guidelines are single- radionuclide guidelines and are linearly proportional to the dose limit used in the calculations. In setting the actual residual soil contamination guides for the LEHR site, DOE will apply the as low as reasonably achievable policy to the decision-making process, along with other factors such as whether a particular scenario is reasonable and appropriate, as well as using site-specific inputs to computer models based on data not yet fully determined

  19. Method of melt-decontaminating alumium contaminated with radioactivity

    International Nuclear Information System (INIS)

    Uda, Tatsuhiko; Iba, Hajime; Miura, Noboru; Kawasaki, Katsuo.

    1986-01-01

    Purpose: To enable optimum deontamination for radioactive-contaminated aluminum by further improving the decontaminating effect of the slag agent added to radioactive contaminated materials. Method: The slag agent is mainly composed of chloride type slags having a high reactivity for mainly incorporating uranium compounds and easily reacting near the melting point of aluminum and incorporated with fluorides for weakening the deliquescent characteristic to the chloride materials. Further, those slag agents are selected which can be treated at a low temperature in order to prevent the uranium compounds once incorporated into the slags from re-melting into the molten aluminum. Typically, a slag agent comprising 14 LiF, 76 KCl - 10 BaCl 2 is preferred. The basicity of the slag agent ranges from 0.5 to 2 and the melting point is 700 deg C. The melting decontaminating efficiency for the radioactive-contaminated aluminum can thus be improved. (Horiuchi, T.)

  20. Chernobyl three years later: radiobiologic evaluation of a radioactive contamination

    International Nuclear Information System (INIS)

    Behar, A.; Cohen-Boulakia, F.; Othmani, S.

    1990-01-01

    On April 26, 1986, after partial fusion and confining loss by explosion of a nuclear reactor, 5 x 10(7) Ci of radionuclides escaped from Chernobyl. Three years later, maps show contamination by radioactive isotopes (formed during that period) of 21,000 km2 of Soviet soil, mainly in Byelorussia and part of the Ukraine. Decontamination measures have not been effective to date and 135,000 persons are being followed medically, taking into account the radioactive doses they received. An initial excess of morbidity from solid tumors has been noted much sooner than in the case of Hiroshima and Nagasaki, but its significance is in dispute. Three years later, only the extent of the ecologic disaster caused by the radioactive contamination can be confirmed. It is too early to draw conclusions about radiation-induced carcinogenesis for the contaminated population

  1. Design and development of food radioactivity contamination monitoring system

    International Nuclear Information System (INIS)

    Narayan, Pradeep; Vaijapurkar, S.G.; Bohra, Dinesh

    2014-01-01

    Radioactivity has been part and parcel of living being since the existence of the earth. It is available everywhere in our environment and being responsible for evolution of life on earth at some extent. However, the radioactivity in excess of the natural radioactive can have harmful effects on living being. The radiation exposure can be of external or internal origin or of both. The main route of internal radiation exposure is through the contaminated food chains. The concentration of natural radioactivity in food varies in range of 40-600 Bq/kg. 40 K being the single major radionuclide of food with typical radioactivity; 50 Bq/kg in milk, 420 Bq/kg in milk powder, 165 Bq/kg in potatoes, and 125 Bq/kg in beef is also the main contributor of natural radiation doses to human being. Measurement of radioactivity in food items and drinks is thus very important in controlling the internal exposure to human being especially in case of nuclear disaster. Though, the methods and techniques for food radioactivity measurement already existing, the need of portable instrument is warranted to measure the radioactivity in food items in raw form. Measurement of radioactivity may help in quick and mass screening of food items in case of nuclear emergencies. Any enhanced level of radioactivity in food items especially in case of nuclear emergency need to be evaluated for controlling its spread and restriction of consumption by the public. This way, it may help in managing internal radioactivity contamination to human being

  2. Dosimetric system for measurement of radioactive contaminations

    International Nuclear Information System (INIS)

    Litynski, Z.; Pienkos, J.P.; Witkowski, J.; Zadrozny, S.

    1985-01-01

    A dosimetric system for personnel dosimetry and monitoring measuring a contamination without time delay and dead time is described. The system ensures many-point measurement and minimalization of background radiation influence. 1 fig. (A.S.)

  3. Radioactive contamination in metal recycling industry - an environmental issue

    International Nuclear Information System (INIS)

    Agarwal, S.P.

    2012-01-01

    Metal recycling has become an important industrial activity worldwide; it is seen as being socially and environmentally beneficial because it conserves natural ore resources and saves energy. However, there have been several accidents over the past decades involving orphan radioactive sources or other radioactive material that were inadvertently collected as metal scrap that was destined for recycling. The consequences of these accidents have been serious with regard to the protection of people and the environment from the harmful effects of ionizing radiation as well as from an economic point of view. India produces and exports steel products to various countries. In the recent years there were rejection and return of steel products as they were found to be contaminated with trace quantities of radioactive materials. During investigation of incidents of radioactive contamination in steel products exported from India, it was observed that steel products are contaminated with low level radioactivity. Though radioactivity level in steel products is found to be too low to pose any significant hazards to the handling personnel or to the users or the public at large, its presence is undesirable and need to be probed as to how it has entered in the steel products. Atomic Energy Regulatory Board (AERB) has investigated the incidents of such nature in the recent past and it is gathered that the steel products are made out of steel produced in a foundry where metal scrap containing radioactive material has been used. In this talk, incidents of radioactive contamination, its roots cause, and its radiological impact on person, property and environment, lessons learnt, remedial measures and international concerns will be discussed

  4. Contaminated Sites by Residues from Romanian Industry

    International Nuclear Information System (INIS)

    Aurelian, F.; Georgescu, D.; Vacariu, V.; Popescu, M.

    2001-01-01

    Full text: In Romania, the mining industries of ferrous ore, non-ferrous ore, bauxite, coal, chemical fertilisers, the extraction of natural gas and oil, etc. have a considerable weight in economy. The study lets us know that in these industries, in different by-products and waste from the process, some radionuclides come out. The preliminary data, which are determined in these industries, are compared with those data, which are published by the countries from EU. There were determined uranium, radium and thorium from ore and sterile (ferrous, non-ferrous, bauxite, talc, clay, asbestos, barytine, salt, coal and bituminous schist). Also, there have been determined the radium and the uranium content of waters from non-uraniferous mining sites. The level of radioactive noxa has been informative determined in each mine. The level of the concentrations requires a systematic research and an assessment of the risk and the impact against the environment, the workers, and the public. (author)

  5. Assessment of sites concerning radioactive contamination during preparation of a Contamination Site Register

    International Nuclear Information System (INIS)

    Gellermann, Rainer; Flesch, Klaus

    2014-01-01

    Experience gained since 1990 in the new, but also old German Federal States has shown that there are radioactive contaminated sites beside the legacies of uranium mining in Germany which caused exposures exceeding the radiation protection limits for members of the public. The reason for this situation is that radioactivity has been excluded in the compilation of the register for potentially hazardous sites that are prepared routinely in the context of soil protection assessments. Moreover, the information contained in these registers is not yet evaluated regarding aspects of radioactivity. In many cases, the information existing at the soil protection authorities needs only to be additionally filtered in order to identify potentially hazardous sites for radioactive contamination. For that reason, the working group ''Natural radioactivity'' (AKNAT) of the German-Swiss Radiation Protection Association developed a specific catalogue of business branches that provides indications for radioactive legacies.

  6. Method of melting and decontaminating radioactive contaminated aluminum material

    International Nuclear Information System (INIS)

    Uda, Tatsuhiko; Miura, Noboru; Kawasaki, Katsuo; Iba, Hajime.

    1986-01-01

    Purpose: To improve the decontaminating efficiency upon melting decontamination of radioactive-contaminated aluminum materials. Method: This invention concerns an improvement for the method of melting decontamination by adding slug agent composed of organic compound to contaminated aluminum material and extracting the radioactive materials into the slug thereby decontaminating the aluminum material. Specifically metals effective for reducing the active amount of aluminum are added such that the content is greater than a predetermined value in the heat melting process. The metal comprises Mg, Cu or a mixture thereof and the content is more than 4 % including those previously contained in the aluminum material. (Ikeda, J.)

  7. Radioactive contamination of the biosphere and consequences for food supply

    International Nuclear Information System (INIS)

    Wiechen, A.

    1989-01-01

    The paper deals with all aspects of radioactive contamination of the biosphere and corresponding consequences for food supply. In particular, releases of radioactivity by nuclear weapon tests in the early 60's and nuclear accidents in recent years are discussed. Contamination of food in the Federal Republic of Germany by these events and corresponding ingestion dose are demonstrated using examples. Furthermore diffusion of radionuclides and their transfer through the food chains to man are described. Suitable methods of decontamination at different production steps and their viability are discussed. (orig.) [de

  8. Radioactive contamination of workers. General recommendation and procedures

    International Nuclear Information System (INIS)

    Mastro, N.L. del; Santos, O.R. dos; Silva, E.N.D.; Santos, A.J. dos.

    1987-09-01

    The present publication has an objective to provide data and information to be used by workers who handle with or eventually could enter in touch with radioactives substances. The authors have made a compilation of subjects got from the literature on several aspects about radiocontamination, physical and chemical characteristics of radioisotopes, main sources of radioactive contamination, biological basis and treatement of internal and external decontamination. Special attention was paid to iodine and actinides contamination, particularly to uranium and plutonium. The conclusion are presented as general recommendation and synoptic tables. (Author) [pt

  9. Long-term trend of radioactive contamination of food products in Bulgaria after the Chernobyl accident

    International Nuclear Information System (INIS)

    Kirov, K.; Marinov, V.; Naidenov, M.

    1997-01-01

    Results which characterize the dynamics for the power of radioactive contamination of foods in the Bulgaria with Cesium radionuclides from May 1986 to December 1995 are presented. It was done for motivation of some conclusions during the progress of radiation situation in Bulgaria after the Chernobyl accident. The data are compared with Maximum residues limits (MRL) of our country as well as that of international organizations. They are compared with the background contamination of foods descended from regions affected after experimental nuclear explosion till 1963 too

  10. Where is New York State relative to cleanup standards for soils contaminated with radioactive materials

    International Nuclear Information System (INIS)

    Merges, P.J.

    1995-01-01

    In September 1993, New York State adopted a cleanup guideline for radioactively contaminated sites being remediated for unrestricted release. This paper reviews this cleanup guideline and discusses its implementation by Bureau of Radiation staff. A cleanup guideline (1) has been adopted by the State of New York which applies to residual radiological contamination on sites undergoing remediation for unrestricted use. The guideline is flexible and allows for alternative site cleanup approaches. The application of this guidance by radiation control program staff is discussed herein. There may be a need to revisit properties that were felt to be open-quotes cleanclose quotes previously - but fail to meet the new guidance

  11. Engineering-scale tests of in situ vitrification to PCB and radioactive contaminated soils

    International Nuclear Information System (INIS)

    Liikala, S.C.

    1991-01-01

    In Situ Vitrification (ISV) is a thermal treatment technology applicable to the remediation of hazardous chemical and radioactive contaminated soil and sludge sites. The ISV process utilizes electricity, through joule heating, to melt contaminated soil and form an inert glass and microcrystalline residual product. Applications of ISV to polychlorinated biphenyls (PCBs) and radionuclides have been demonstrated at engineering-scale in numerous tests (1,2,3). An updated evaluation of ISV applicability to treatment of PCBs and radionuclides, and recent test results are presented herein

  12. Transfer of radioactive contamination from milk to commercial dairy products

    International Nuclear Information System (INIS)

    Wilson, L.G.; Sutton, P.M.

    1988-01-01

    The fate of radioactive contamination resulting from fallout from the Chernobyl accident was studied during milk processing. A range of commercial dairy products was produced on a pilot-laboratory scale and the radiocaesium contents were measured by high-resolution gamma spectrometry. The results show that the radiocaesium partitioned with the water phase and therefore butter, cream and cheese had relatively low levels of radioactivity. Ion exchange demineralization was effective in removing radiocaesium from whey. Ultrafiltration of whey resulted in a reduction of radioactivity relative to retentate solids. (author)

  13. Radiation safety for incineration of radioactive waste contaminated by cesium

    International Nuclear Information System (INIS)

    Veryuzhs'kij, Yu.V.; Gryin'ko, O.M.; Tokarevs'kij, V.V.

    2016-01-01

    Problems in the treatment of radioactive waste contaminated by cesium nuclides are considered in the paper. Chornobyl experience in the management of contaminated soil and contaminated forests is analyzed in relation to the accident at Fukushima-1. The minimization of release of cesium aerosols into atmosphere is very important. Radiation influence of inhaling atmosphere aerosols polluted by cesium has damage effect for humans. The research focuses on the treatment of forests contaminated by big volumes of cesium. One of the most important technologies is a pyro-gasification incineration with chemical reactions of cesium paying attention to gas purification problems. Requirements for process, physical and chemical properties of treatment of radioactive waste based on the dry pyro-gasification incineration facilities are considered in the paper together with the discussion of details related to incineration facilities. General similarities and discrepancies in the environmental pollution caused by the accidents at Chornobyl NPP and Fukushima-1 NPP in Japan are analyzed

  14. Test and evaluation of radioactively contaminated transducers and transmitters

    International Nuclear Information System (INIS)

    Strahm, R.C.

    1983-01-01

    People in the nuclear industries face some unique problems when handling, testing, or examining transducers and transmitters that have been radioactively contaminated. Although many people and organizations, including EG and G Idaho, have performed such work for many years, there are no set, structured approaches or procedures. This paper discusses a disciplined laboratory approach to contaminated transducer testing and evaluation, utilizing equipment and facilities developed specifically for this type of work

  15. Soil magnetic susceptibility as indicator of radioactive contamination

    International Nuclear Information System (INIS)

    Curda, S.

    2006-01-01

    Measurement of magnetic susceptibility is a method, which is used in many areas of research. The locality Ak-Tjuz is typical example of old ecological load. One of the negative effects represents radioactive contamination. This situation is caused by environmental disaster in 1964. For useful reparation it is really necessary to determinate the surface range of contamination. And measurement of the magnetic susceptibility could be the suitable method for that kind of monitoring. (author)

  16. The role of bioindicators in assessing radioactive contamination

    International Nuclear Information System (INIS)

    Marovicj, G.

    1990-01-01

    The paper is a survey of investigations into radioactive contamination of selected plant and animal species (bioindicators) which have the capacitr for multiple accumulation of fission products. Literature data on the contamination of bioindicators are compared with special reference to the accumulation of 131 I, 137 Cs and 90 Sr as a result of atmospheric nuclear experiments and the nuclear accident at Chernobyl. (author) 52 refs.; 3 figs [sh

  17. Control criteria for residual contamination in materials considered for recycle and reuse

    International Nuclear Information System (INIS)

    Kennedy, W.E. Jr.; Hill, R.L.; Aaberg, R.L.

    1993-11-01

    Pacific Northwest Laboratory (PNL) is collecting data and conducting technical analyses to support the US Department of Energy (DOE), Office of Environmental Guidance, Air, Water, and Radiation Division (DOE/EH-232) in determining the feasibility of developing radiological control criteria for recycling or reuse of metals or equipment containing residual radioactive contamination from DOE operations. The criteria, framed as acceptable concentrations for release of materials for recycling or reuse, will be risk-based and will be developed through analysis of radiation exposure scenarios and pathways. The analysis will include evaluation of relevant radionuclides, potential mechanisms of exposure, and non-health-related impacts of residual radioactivity on electronics and film. The analyses will consider 42 key radionuclides that are generated during DOE operations and may be contained in recycled or reused metals or equipment

  18. Rapid Evaluation of Radioactive Contamination in Rare Earth Mine Mining

    Science.gov (United States)

    Wang, N.

    2017-12-01

    In order to estimate the current levels of environmental radioactivity in Bayan Obo rare earth mine and to study the rapid evaluation methods of radioactivity contamination in the rare earth mine, the surveys of the in-situ gamma-ray spectrometry and gamma dose rate measurement were carried out around the mining area and living area. The in-situ gamma-ray spectrometer was composed of a scintillation detector of NaI(Tl) (Φ75mm×75mm) and a multichannel analyzer. Our survey results in Bayan Obo Mine display: (1) Thorium-232 is the radioactive contamination source of this region, and uranium-238 and potassium - 40 is at the background level. (2) The average content of thorium-232 in the slag of the tailings dam in Bayan Obo is as high as 276 mg/kg, which is 37 times as the global average value of thorium content. (3) We found that the thorium-232 content in the soil in the living area near the mining is higher than that in the local soil in Guyang County. The average thorium-232 concentrations in the mining areas of the Bayan Obo Mine and the living areas of the Bayan Obo Town were 18.7±7.5 and 26.2±9.1 mg/kg, respectively. (4) It was observed that thorium-232 was abnormal distributed in the contaminated area near the tailings dam. Our preliminary research results show that the in-situ gamma-ray spectrometry is an effective approach of fast evaluating rare earths radioactive pollution, not only can the scene to determine the types of radioactive contamination source, but also to measure the radioactivity concentration of thorium and uranium in soil. The environmental radioactive evaluation of rare earth ore and tailings dam in open-pit mining is also needed. The research was supported by National Natural Science Foundation of China (No. 41674111).

  19. Residual radioactivity in the soil of the Semipalatinsk Nuclear Test Site in the former USSR.

    Science.gov (United States)

    Yamamoto, M; Tsukatani, T; Katayama, Y

    1996-08-01

    This paper deals with our efforts to survey residual radioactivity in the soil sampled at the Semipalatinsk Nuclear Test Site and at off-site areas in Kazakhstan. The soil was sampled at the hypocenter where the first Soviet nuclear explosion was carried out on 29 August 1949, and at the bank of the crater called "Bolapan," which was formed by an underground nuclear detonation on 15 January 1965 along the Shagan River. As a comparison, other soil was also sampled in the cities of Kurchatov and Almaty. These data have allowed a preliminary evaluation of the contemporary radioactive contamination of the land in and around the test site. At the first nuclear explosion site and at Bolapan, higher than background levels of 239,240Pu with weapons-grade plutonium were detected together with fission and activation products such as 137Cs, 60Co, 152Eu, and 154Eu.

  20. Radioactive substances found on the contaminated fish

    Energy Technology Data Exchange (ETDEWEB)

    Kiba, T; Ohashi, S; Shibata, M; Mizube, T

    1954-01-01

    Radiochemical investigation of the substance collected from the surface of tuna fish which were brought back by the No. 5 Fukuryu Maru was performed. Most of the radioactivity was found on the scales which could not be decontaminated by treating with H/sub 2/O; 80% of the activity was removed by washing the dried scales with 3N HCl. Paper chromatographic separation of the HCl fraction showed the presence of /sup 140/Ba, /sup 89/Sr, /sup 132/Te, and probably /sup 95/Zr, /sup 140/La, and rare earths.

  1. Biological effects of water reservoir radioactive contamination

    International Nuclear Information System (INIS)

    Mashneva, N.I.

    1983-01-01

    Radiation damage to fresh water fishes at early stages of ontogenesis is revealed only during the spawn incubation in a solution with 10 -5 to 10 -3 Cu/l radioactivity and at relatively high dosages exceeding 500-1000 rad. Damaging effect of a fission product mixture of 9, 30 and 100 day age as well as of several separate radionuclides on embryogenesis of freshwater fishes depends mainly on fish species, concentration, toxicity, chemical form of radionuclides in the residence medium, on peculiarities of metabolism between the aqueous medium and an organism, stage of the embryo development by the moment of radiation effect and duration of this effect

  2. Radiological risk assessment of a radioactively contaminated site

    International Nuclear Information System (INIS)

    Devgun, J.S.

    1990-01-01

    A limited-scope preliminary assessment of radiological risk has been conducted at a radioactively contaminated site under current site use conditions and based on the available preliminary radiological characterization data for the site. The assessment provides useful input to the remedial action planning for the site. 8 refs., 1 fig., 2 tabs

  3. Radioactive contamination, what actions for the polluted sites

    International Nuclear Information System (INIS)

    2004-01-01

    The nuclear safety authority and the direction of prevention of pollutions and risks have organised the first edition of the national colloquium: radioactive contamination: what actions for polluted sites. Four axes can be taken to follow this colloquium: prevention, outstanding tools to evaluate risks and rehabilitation, a better responsibility of operators and memory keeping. (N.C.)

  4. Radioactive air and surface contamination in Czechia and Slovakia

    International Nuclear Information System (INIS)

    Rumyantsev, V.V.

    1992-01-01

    Data are presented on the radioactive substance effluents into the environment in conditions of NPP normal operation and on the air contamination by 85 Kr due to operation of the European and Soviet plants for reprocessing spent nuclear fuel. Data are given on the dosage of the Czechoslovakia population due to the Chernobyl NPP accident

  5. Radioactive contamination from Chernobyl accident over Alexandria city

    International Nuclear Information System (INIS)

    Ammar, E.A.; El-Khatib, A.M.; Wahba, A.G.; Elraey, M.

    1987-01-01

    The concentration of radioactive contamination in air resulting from the Chernobyl accident has been followed up. A sudden and sharp increase was detected seven days after the start of the accident. This increase amounted to about 650 times the normal air-borne activity. (author)

  6. Thermoexoemission detectors for monitoring radioactive contamination of industrial waste waters

    International Nuclear Information System (INIS)

    Obukhov, V.T.; Sobolev, I.A.; Khomchik, L.M.

    1987-01-01

    Detectors on base of BeO(Na) monocrystals with thermoemission to be used for monitoring radioactive contamination of industrial waste waters are suggested. The detectors advantages are sensitivity to α and low-ehergy β radiations, high mechanical strength and wide range of measurements. The main disadvantage is the necessity of working in red light

  7. Microwave/vacuum drying treatment of radioactively contaminated animal carcasses

    International Nuclear Information System (INIS)

    Chen Zongming; Zhang Yinsheng; Teng Hongdi; Zhu Chongde; Ge Lixin; Wang Jinliang

    1994-01-01

    The paper describes a microwave/vacuum drying process for the treatment of radioactively contaminated animal carcasses. The experiment demonstrated the feasibility of the process. The treatment process could completely remove the water from carcasses and effectively extend the preservation period. No radiological impact was found on workplace and environment

  8. Protection against radioactive contamination of foods and agricultural products

    International Nuclear Information System (INIS)

    Szabo, A.; Kovacs, Z.

    1977-01-01

    Methods suitable for diminishing radioactive contamination of foods and agricultural products and reducing at the same time the irradiation hazards for the human organism are dealt with. The possibilities for the decontamination of foods vegetal and of animal origin are discussed separately. (author)

  9. Residual contamination and corrosion on electrochemically marked uranium

    International Nuclear Information System (INIS)

    Seals, R.D.; Bullock, J.S.; Bennett, R.K.

    1981-01-01

    Residual contamination and potential corrosion problems on uranium parts resulting from PHB-1 and PHB-1E electroetchants have been investigated using ion microprobe mass analysis (IMMA), scanning electron microscopy (SEM), and light microscopy (LM). The effectiveness of various solvent cleaning sequences and the influence of the use of an abrasive cleaner were evaluated. The marking thicknesses and chlorine distributions were determined

  10. Phase II, Title I engineering assessment of radioactive sands and residues, Lowman Site, Lowman Idaho

    International Nuclear Information System (INIS)

    1977-12-01

    An engineering assessment was performed of the problems resulting from the existence of radioactive uranium sand residues at the Lowman, Idaho, site. Services normally include the preparation of topographic maps, the performance of core drillings and radiometric measurements sufficient to determine areas and volumes of tailings and other radium-contaminated materials, the evaluation of resulting investigations of site hydrology and meteorology, and the evaluation and costing of alternative corrective actions. Radon gas release from the 90,000 tons of sand residues at the Lowman site constitutes the most significant environmental impact, although external gamma radiation is also a factor. The two alternative actions presented are dike construction, fencing, and maintenance (Option I); and consolidation of the piles, addition of a 2-ft-thick stabilization cover, and on-site cleanup (Option II). Both options include remedial action at off-site structures. Cost estimates for the two options are $393,000 and $590,000

  11. Phase II, Title I engineering assessment of radioactive sands and residues, Lowman Site, Lowman Idaho

    Energy Technology Data Exchange (ETDEWEB)

    1977-12-01

    An engineering assessment was performed of the problems resulting from the existence of radioactive uranium sand residues at the Lowman, Idaho, site. Services normally include the preparation of topographic maps, the performance of core drillings and radiometric measurements sufficient to determine areas and volumes of tailings and other radium-contaminated materials, the evaluation of resulting investigations of site hydrology and meteorology, and the evaluation and costing of alternative corrective actions. Radon gas release from the 90,000 tons of sand residues at the Lowman site constitutes the most significant environmental impact, although external gamma radiation is also a factor. The two alternative actions presented are dike construction, fencing, and maintenance (Option I); and consolidation of the piles, addition of a 2-ft-thick stabilization cover, and on-site cleanup (Option II). Both options include remedial action at off-site structures. Cost estimates for the two options are $393,000 and $590,000.

  12. Radioactivity measurement of radioactive contaminated soil by using a fiber-optic radiation sensor

    Science.gov (United States)

    Joo, Hanyoung; Kim, Rinah; Moon, Joo Hyun

    2016-06-01

    A fiber-optic radiation sensor (FORS) was developed to measure the gamma radiation from radioactive contaminated soil. The FORS was fabricated using an inorganic scintillator (Lu,Y)2SiO5:Ce (LYSO:Ce), a mixture of epoxy resin and hardener, aluminum foil, and a plastic optical fiber. Before its real application, the FORS was tested to determine if it performed adequately. The test result showed that the measurements by the FORS adequately followed the theoretically estimated values. Then, the FORS was applied to measure the gamma radiation from radioactive contaminated soil. For comparison, a commercial radiation detector was also applied to measure the same soil samples. The measurement data were analyzed by using a statistical parameter, the critical level to determine if net radioactivity statistically different from background was present in the soil sample. The analysis showed that the soil sample had radioactivity distinguishable from background.

  13. Treatment of radioactive contaminated water in nuclear power plants

    International Nuclear Information System (INIS)

    1978-12-01

    This rule is to be applied to the design, construction, and operation of facilities for treatment of water contaminated with radioactive material in stationary nuclear power plants with LWRs and HTRs. According to the requirements of the rule these facilities are to be designed, constructed, and operated in such a way that a) uncontrolled discharge of water contaminated with radioactive material is avoided, b) the activity discharged with water is as low as possible, c) water contaminated with radioactive material will not reach the ground, d) the radiation exposure as a consequence of direct radiation, contamination, and inhalation of the persons occupied in the facilities is as low as possible and as a maximum corresponds to the values laid down in the radiation protection regulation or to the values of the operating license. This rule is not to be applied to facilities for coolant and storage pit clean-up as well as facilities for the treatment of concentrates produced during the contamination of the water. (orig./HP) [de

  14. Protection of environmental contamination by radioactive materials and remediation of environment

    International Nuclear Information System (INIS)

    2003-05-01

    This report consisted of the environmental contamination of radioactive and non-radioactive materials. 38 important accident examples of environmental contamination of radioactive materials in the world from 1944 to 2001 are stated. Heavily polluted areas by accidents are explained, for example, Chernobyl, atomic reactor accidents, development of nuclear weapon in USA and USSR, radioactive waste in the sea. The environmental contamination ability caused by using radioactive materials, medical use, operating reactor, disposal, transferring, crashing of airplane and artificial satellite, release are reported. It contains measurements and monitor technologies, remediation technologies of environmental contamination and separation and transmutation of radioactive materials. On the environmental contamination by non-radioactive materials, transformation of the soil contamination in Japan and its control technologies are explained. Protection and countermeasure of environmental contamination of radioactive and non-radioactive materials in Japan and the international organs are presented. There are summary and proposal in the seventh chapter. (S.Y.)

  15. Contamination and decontamination of vehicles when driven in radioactive areas

    International Nuclear Information System (INIS)

    Ulvsand, T.; Nygren, U.

    1999-10-01

    There is reason to ask whether it is beneficial to decontaminate vehicles, in view of the great effort applied. If the level of contamination is low before the decontamination process, then the cost is not motivated, even if the decontamination is shown to be effective in relative terms. The report describes two trials at the National NBC Defence School in Umeaa and one trial at the French test site in Bourges. The aim is to investigate how vehicles are contaminated and at which ground deposition levels troublesome levels of contamination will arise. In the trials, a non-radioactive agent substituting real radioactivity was used. The trials in Sweden so far have used the oversnow vehicle BV 206, during both winter and summer conditions. The vehicles were driven a specific distance along a road on which a known amount of the test substance had been dispersed. Samples were taken on pre-determined areas on one side of the vehicles to measure the amount of test substance. Later, the vehicles continued along a 'clean' road where additional samples were taken, but on the other side of the vehicles. The largest amount of test substance was collected on the tracks and on the back of the vehicle. The tracks and mud-flaps were effectively decontaminated when the vehicles were driven along a clean road, while most of the contamination remained on the backside. The purpose of the trials in France was to compare the results from our non-radioactive and their radioactive method, based on the radioactive La-140. Due to ground conditions, the level of contamination on the vehicles was much less than in the trials in Umeaa, but the effect decontamination could be measured after all

  16. Contamination and decontamination of vehicles driven in radioactive areas

    International Nuclear Information System (INIS)

    Ulvsand, T.; Nygren, U.

    1999-03-01

    There is reason to ask whether it is beneficial to decontaminate vehicles, in view of the great effort applied. If the level of contamination is low before the decontamination process, then the cost is not motivated, even if the decontamination is shown to be effective in relative terms. The report describes two trials at the National NBC Defence School in Umeaa and one trial at the French test site in Bourges. The aim is to investigate how vehicles are contaminated and at which ground deposition levels troublesome levels of contamination will arise. In the trials, a non-radioactive agent substituting real radioactivity was used. The trials in Sweden so far have used the oversnow vehicle BV 206, during both winter and summer conditions. The vehicles were driven a specific distance along a road on which a known amount of the test substance had been dispersed. Samples were taken on pre-determined areas on one side of the vehicles to measure the amount of test substance. Later, the vehicles continued along a 'clean' road where additional samples were taken, but on the other side of the vehicles. The largest amount of test substance was collected on the tracks and on the back of the vehicle. The tracks and mud-flaps were effectively decontaminated when the vehicles were driven along a clean road, while most of the contamination remained on the backside. The purpose of the trials in France was to compare the results from our non-radioactive and their radioactive method, based on the radioactive La-140. Due to ground conditions, the level of contamination on the vehicles was much less than in the trials in Umeaa, but the effect decontamination could be measured after all

  17. Protection against radioactive contamination of food and agricultural products

    International Nuclear Information System (INIS)

    Szabo, A.; Kovacs, Z.

    1977-01-01

    Due to contaminating effects from nuclear explosions and nuclear power plants, the systematic investigation of environmental radioactive contamination is absolutely necessary. In order to reduce the artificial radiation dose to which the human body is exposed, isotope content of foods and agricultural products should be known. The authors evaluate the decontamination possibilities of food produced from vegetable and animal products, starting from the contamination of some products. For vegetable product decontamination the use of suitable fertilizers, thorough scrubbing in excess water and, for cereals, milling is proposed. As the most effective preventive measure of radiation contamination of food products of animal origin, appropriate packing is proposed. The storage and preservation problems are emphasized for short half-life radiation contamination. (P.J.)

  18. The supposed radioactive contamination of the Puelche aquifer

    International Nuclear Information System (INIS)

    Martini, Leopoldo E.

    2005-01-01

    The paper attempts to clarify the supposed radioactive contamination of the Puelche Aquifer in the Ezeiza Atomic Center Area, Ezeiza, province of Buenos Aires (Argentina). Reports are listed that show categorically that no anthropogenic uranium contamination is present. As far as the nitrates contamination is concerned, it is not generated by the Ezeiza Atomic Center, because the Center is downward from the contaminated zone. It is possible that the contamination is produced by houses in the area without suitable sewage. In the present case the best contribution to the environmental right, besides the adaptation and the systematization of the different legal instruments, is to found the analysis of the facts on the scientific and technical knowledge. (author) [es

  19. Radioactivity contamination of the Russian Arctic Seas

    Energy Technology Data Exchange (ETDEWEB)

    Rissanen, K. [STUK Radiation and Nuclear Safety Authority, Rovaniemi (Finland); Ikaeheimonen, T.K. [STUK Radiation and Nuclear Safety Authority, Helsinki (Finland); Matishov, D.; Matishov, G.G. [Murmansk Marine Biological Inst., Murmansk (Russian Federation)

    2001-04-01

    The levels of the anthropogenic radionuclides in the Russian Arctic Seas are low compared to the potential sources of pollution and originata mainly from the global fallout, Chernobyl fallout and from the western nuclear fuel reprocessing plants. Fresh release of radioactivity was noticed in this study only in the Kola Bay and in two sampling locations in the White Sea. The increased {sup 137}Cs concentrations measured in the estuaries of River Dvina and River Yenisey are caused by the riverine transport from the large catchment area. The sediments of the Russian Arctic Seas are hard. Good and enough long cores for sedimentation rate determination were obtained only in two locations in the White Sea. All the cores from river estuaries were badly mixed. (EHS)

  20. The experimental study of residual radioactivity induced in electrostatic deflector

    Directory of Open Access Journals (Sweden)

    Xu Chong

    2017-01-01

    Full Text Available As one of the key components of Sector Focusing Cyclotron at the Institute of Modern Physics, Chinese Academy of Sciences, the electrostatic deflector can be activated by primary and secondary particles, because of a mismatch between the actual value and the design value of the emittance and emergence angle. In addition, it will be struck by more particles, since there is a stray magnetic field and outgas from the surface of the electrostatic deflector. The residual radioactivity in the electrostatic deflector has been studied in two aspects: specific activity and residual dose rate, based on the gamma-ray spectrometry and Fluke 451p ionization chamber, respectively. The specific activity of radionuclides in the main components and the dust on the enclosure have been investigated by using gamma-ray spectrometry. The residual dose rate around the electrostatic deflector has been obtained by Fluke 451p ionization chamber. The results of the study show that there is a non-negligible radiological risk to the staff. This result can be provided as guidance for making a maintenance schedule, so that the dose received by staff can be kept as low as reasonably achievable. Based on the results, advice for "hands-on" maintenance and decommissioning of the SFC have been provided.

  1. Development of risk-based computer models for deriving criteria on residual radioactivity and recycling

    International Nuclear Information System (INIS)

    Chen, Shih-Yew

    1995-01-01

    Argonne National Laboratory (ANL) is developing multimedia environmental pathway and health risk computer models to assess radiological risks to human health and to derive cleanup guidelines for environmental restoration, decommissioning, and recycling activities. These models are based on the existing RESRAD code, although each has a separate design and serves different objectives. Two such codes are RESRAD-BUILD and RESRAD-PROBABILISTIC. The RESRAD code was originally developed to implement the U.S. Department of Energy's (DOE's) residual radioactive materials guidelines for contaminated soils. RESRAD has been successfully used by DOE and its contractors to assess health risks and develop cleanup criteria for several sites selected for cleanup or restoration programs. RESRAD-BUILD analyzes human health risks from radioactive releases during decommissioning or rehabilitation of contaminated buildings. Risks to workers are assessed for dismantling activities; risks to the public are assessed for occupancy. RESRAD-BUILD is based on a room compartmental model analyzing the effects on room air quality of contaminant emission and resuspension (as well as radon emanation), the external radiation pathway, and other exposure pathways. RESRAD-PROBABILISTIC, currently under development, is intended to perform uncertainty analysis for RESRAD by using the Monte Carlo approach based on the Latin-Hypercube sampling scheme. The codes being developed at ANL are tailored to meet a specific objective of human health risk assessment and require specific parameter definition and data gathering. The combined capabilities of these codes satisfy various risk assessment requirements in environmental restoration and remediation activities. (author)

  2. Development of risk-based computer models for deriving criteria on residual radioactivity and recycling

    International Nuclear Information System (INIS)

    Chen, S.Y.

    1994-01-01

    Argonne National Laboratory (ANL) is developing multimedia environmental pathway and health risk computer models to assess radiological risks to human health and to derive cleanup guidelines for environmental restoration, decommissioning, and recycling activities. These models are based on the existing RESRAD code, although each has a separate design and serves different objectives. Two such codes are RESRAD-BUILD and RESRAD-PROBABILISTIC. The RESRAD code was originally developed to implement the US Department of Energy's (DOE's) residual radioactive materials guidelines for contaminated soils. RESRAD has been successfully used by DOE and its contractors to assess health risks and develop cleanup criteria for several sites selected for cleanup or restoration programs. RESRAD-BUILD analyzes human health risks from radioactive releases during decommissioning or rehabilitation of contaminated buildings. Risks to workers are assessed for dismantling activities; risks to the public are assessed for occupancy. RESRAD-BUILD is based on a room compartmental model analyzing the effects on room air quality of contaminant emission and resuspension (as well as radon emanation), the external radiation pathway, and other exposure pathways. RESRAD-PROBABILISTIC, currently under development, is intended to perform uncertainty analysis for RESRAD by using the Monte Carlo approach based on the Latin-Hypercube sampling scheme. The codes being developed at ANL are tailored to meet a specific objective of human health risk assessment and require specific parameter definition and data gathering. The combined capabilities of these codes satisfy various risk assessment requirements in environmental restoration and remediation activities

  3. Environmental remediation. Strategies and techniques for cleaning radioactively contaminated sites

    International Nuclear Information System (INIS)

    Falck, W. Eberhard

    2001-01-01

    Actions for a cleaner and safety environment have risen on social and political agendas in recent years. They include efforts to remediate contaminated sites posing a radiological risk to humans and the surrounding environment. Radiological risks can result from a variety of nuclear and non-nuclear activities. They include: nuclear or radiological accidents; nuclear weapons production and testing; poor radioactive waste management and disposal practices; industrial manufacturing involving radioactive materials; conventional mining and milling of ores and other production processes, e.g. oil and gas production, resulting in enhanced concentrations of naturally occurring radioactive materials (NORMs). The IAEA has developed a comprehensive programme directed at the remediation of radioactively contaminated sites. The programme collates and distributes knowledge about contaminated sites; appropriate methods for their characterization; assessment of their potential environmental and radiological impact; and applicable methods for their clean-up, following internationally recommended safety criteria. The overall resources, and which are technologically less advanced, to focus their efforts and chose appropriate strategies for the abatement or removal of exposure to radiation. An important aspect is the intention to 'close the loop' in the nuclear fuel cycle in the interests of sustainable energy development including nuclear power

  4. Radioactive contamination in a private residence

    International Nuclear Information System (INIS)

    Marsh, W.B.E.

    1986-01-01

    A brief report is given of the contamination of a private house and garden belonging to a deceased medical physicist who had been employed by a large teaching hospital and major research organization and who had his own home laboratory. Gamma dose rates about 1.5 μSvh -1 in the laboratory, 1-2 μSvh -1 in the lounge, 0.4-0.8 μSvh -1 on items of furniture and a fireplace, 0.1 mSvh -1 in the garden shed and 0.15 to 2.0 μSvh -1 in the garden were measured. The decontamination measures performed by the NRPB to clear the area are described. (U.K.)

  5. Theoretical investigation of aspects of radioactive contamination

    International Nuclear Information System (INIS)

    Smith, A.H.; Chandratillake, M.R.; Taylor, J.B.

    1998-01-01

    The BNFL programme of work has investigated theoretical aspects of the mechanisms responsible for the deposition and adherence of contamination to metallic surfaces and the energetics of physical decontamination processes. The work has been conducted in two phases: The theoretical and laboratory study of deposition of species from aqueous media on to stainless steel; Theoretical assessment of the forces causing the attraction of PuO 2 and UO 2 particles to stainless steel in an air environment and comparison of these forces with the energies delivered by physical jetting processes. The first phase produced a model which was found to give good agreement with plant operational experience of the deposition of simple aqueous ions such as Cobalt. Due to the complexities, however, of surface / colloid and surface / particle interactions the model was found not to be successful at predicting deposition for more complex compounds, such as Ruthenium Nitrosyls. At this stage the model had fulfilled its original requirement of underpinning design work on pipework shielding systems and it was decided not to pursue the library of chemical speciation data that would be necessary to model the behaviour of a full spectrum of possible contaminants. The second phase predicts by theoretical analysis that the relation of the energy delivered by jetting techniques to the physical forces causing the adherence of PuO 2 and UO 2 particles will vary considerably with particle size. This is particularly notably for larger PuO 2 particles which are firmly held as a result of high levels of electrostatic charge due to their intense alpha activity. Small particles tend to be difficult to remove due to the low profile that they present to the jetting medium. Large and small PuO 2 particles and small UO 2 particle are thus predicted to be difficult to remove and will present an energy threshold which may not be crossed by all decontamination techniques. (author)

  6. Distinguishing method for contamination/radio-activation of radioactive wastes

    International Nuclear Information System (INIS)

    Fukazawa, Takuji; Kato, Keiichiro; Koda, Satoshi.

    1994-01-01

    The present invention concerns a method of distinguishing the contamination/radio-activation of radioactive wastes used in processing wastes generated upon dismantling of exhausted nuclear reactors. Especially, contaminated/radio-activation is distinguished for wastes having openings such as pipes and valves, by utilizing scattering of γ-rays or γ-ray to β-ray ratio. That is, ratio of scattered γ-rays and direct γ-rays or ratio of β-rays and γ-rays from radioactive wastes are measured and compared by a radiation detector, to distinguish whether the radioactive wastes contaminated materials or radio-activated materials. For example, when an object to be measured having an opening is contaminated at the inner side, the radiation detector facing to the opening mainly detects high direct γ-rays emitted from the object to be measured while a radiation detector not facing the opening mainly detects high scattered γ-rays relatively. On the other hand, when the object is a radio-activated material, any of the detectors detect scattered γ-rays, so that they can be distinguished by these ratios. (I.S.)

  7. Industrial-Scale Processes For Stabilizing Radioactively Contaminated Mercury Wastes

    International Nuclear Information System (INIS)

    Broderick, T. E.; Grondin, R.

    2003-01-01

    This paper describes two industrial-scaled processes now being used to treat two problematic mercury waste categories: elemental mercury contaminated with radionuclides and radioactive solid wastes containing greater than 260-ppm mercury. The stabilization processes were developed by ADA Technologies, Inc., an environmental control and process development company in Littleton, Colorado. Perma-Fix Environmental Services has licensed the liquid elemental mercury stabilization process to treat radioactive mercury from Los Alamos National Laboratory and other DOE sites. ADA and Perma-Fix also cooperated to apply the >260-ppm mercury treatment technology to a storm sewer sediment waste collected from the Y-12 complex in Oak Ridge, TN

  8. Occupational radioactive contamination of cement handlers of the civil construction

    International Nuclear Information System (INIS)

    Santos, Pedro Lopes dos; Gouvea, Rita de Cassia dos Santos; Kelecom, Alphonse; Dutra, Iedo Ramos

    1999-01-01

    Due to their occupational activities, several classes of workers are exposed to radioactive contamination by materials they handle and that contain traces of uranium and its descendants. This is the case of people that work in the civil construction and that currently handle Portland cement. Among other radioactive elements, cement contains the highly radiotoxic polonium-210 which may promote skin cancer because of its high specific activity and high LET α-particle it emits. Concentrations of polonium-210 are reported for urine, hair and skin smear of workers of the civil construction that usually handle cement. The results are compared to a control group. (author)

  9. Allowable residual contamination levels for decommissioning. Part 2. A summary of example results

    International Nuclear Information System (INIS)

    Kennedy, W.E. Jr.; Napier, B.A.

    1985-01-01

    This paper contains a description of the results of a study sponsored by UNC Nuclear Industries to determine Allowable Residual Contamination Levels (ARCL) for decommissioning facilities in the 100 Areas of the Hanford Site. ARCL results are presented both for surface contamination remaining in facilities (in dpm/100 cm 2 ) and for unconfined surface and confined subsurface soil conditions (in pCi/g). Two confined soil conditions are considered: contamination at depths between 1 and 4 m, and contamination at depths greater than or equal to 5 m. A set of worksheets are discussed for modifying the ARCL values to accommodate changes in the radionuclide mixture or concentrations, to consider the impacts of radioactive decay, and to predict instrument responses. Finally, a comparison is made between the unrestricted release ARCL values for the 100 Area facilities and existing decommissioning and land disposal regulations. For surface contamination, the comparison shows good agreement for a selected annual dose limit. For soil contamination, the comparison shows good agreement if reasonable modification factors are applied to account for the differences in modeling soil contamination and licensed low-level waste. 6 references, 1 figures, 4 tables

  10. Transporting large volumes of residual radioactive material: FUSRAP solutions

    International Nuclear Information System (INIS)

    Pressnell, T.; McDaniel, P.; Darby, J.

    1997-01-01

    During the 1940s, 1950s and 1960s, many sites in the United States were used by the Manhattan Engineer District and the Atomic Energy Commission for processing and storing uranium and thorium ores and metals. Some of the sites were owned by the federal government; others were owned by universities or other institutions; and still others, such as chemical plants, were privately owned. The Formerly Utilized Sites Remedial Action Program (FUSRAP) is one of several U.S. Department of Energy programs created to address radioactive contamination in excess of guidelines at these sites. FUSRAP currently includes 46 sites in 14 states. This article includes the following topics in describing FUSRAP work: Logistics challenges; engineering challenges (package inspection, equipment compatability, moisture content requirements, waste volume estimation); Traffic management

  11. Treatment of Gravel Contaminated with Naturally Occurring Radioactive Element

    International Nuclear Information System (INIS)

    Sohsah, M. A.; Kamal, S. M.; Mamoon, A.

    2004-01-01

    Environmental protection primarily means controlling the releases of radioactive and non-radioactive wastes to the environment and involves treatment, storage, cleanup and disposal of these wastes. The present study concerns the cleanup of gravel that has been contaminated with 2 26 R a. Aqueous solutions of different compositions including water and various concentrations of calcium chloride and barium chloride were used to leach the contaminated gravel. The leaching experiments were carried out in glass column. In some leaching experiments, samples of sandy soil were placed below the gravel to test the sorption of the leached 2 26 R a by the soil. The relative efficiencies of the leachant and the extent of sorption of the leached radionuclide were determined both by the liquid scintillation counting and by the thermoluminescent chips. The TLD chips record the dose before and after decontamination of the gravel and before and after contamination of the soil samples when used. The results obtained indicated that acidified barium chloride was relatively the most effective leachant of 2 26 R a contamination. It reduced the dose from the contaminated gravel to almost half. The soil sample used adsorbs the leached radionuclides efficiently, increasing the soil naturally low dose to about six folds

  12. Dosskin code for radiological evaluation of skin radioactive contaminations

    International Nuclear Information System (INIS)

    Cornejo D, N.

    1996-01-01

    The conceptual procedure and computational features of the DOSSKIN code are shown. This code calculates, in a very interactive way, skin equivalent doses and radiological risk related to skin radioactive contaminations. The evaluation takes into account the contributions of contaminant daughter nuclides and backscattering of beta particles in any skin cover. DOSSKIN also allows to estimate the maximum time needed to decontaminate the affected zone, using, as input quantity, the limit value of skin equivalent dose considered by users. The comparison of the results obtained by the DOSSKIN code with those reported by different authors are showed. The differences of results are less than 30%. (authors). 4 refs., 3 fig., 1 tab

  13. Protection of atmospheric air against radioactive gas and aerosol contaminants

    International Nuclear Information System (INIS)

    Zykova, A.S.

    1984-01-01

    Measures for contamination protection of atmospheric air subdivided into active and passive ones, are considered. The active measures envisage: development and application of waste-free flowsheets, use of flowsheets which restrict formation of gaseous-aerosol discharges; application of highly efficient treatment facilities torage. Dispersion of radioactive substances, released with discharges to the atmosphere, using high stacks; development of the corresponding site-selection solutions and arrangement of sanitary protective zones belong to passive measures. Measures for protection of atmospheric air also include waste and air contamination monitoring. The measures described are considered as applied to NPPs

  14. Internal radioactive contamination in selected groups of CRNL employees

    International Nuclear Information System (INIS)

    Evans, D.W.S.

    1975-10-01

    This report details the development and execution of a 30 month program designed to characterize the magnitude and distribution of internal radioactive contaminaton amongst selected groups of employees at Chalk River Nuclear Laboratories, using a shadow shield whole-body counter. The results show that the levels of contamination in these employees are very low, and no contaminant was present in amounts exceeding 10% of the maximum permissible body burden, with the exception of a medically administered radionuclide (selenium-75). Details of the time course of some of the body burdens are also furnished. (author)

  15. Radiological risk assessment for radioactive contamination at landfill site

    International Nuclear Information System (INIS)

    Devgun, J.S.

    1990-01-01

    A limited-scope preliminary assessment of radiological risk has been conducted for a landfill site where radioactive residues resulting from past uranium ore processing operations are present. Potential radiation doses to an individual under different scenarios have been predicted using the RESRAD computer code. The assessment provides useful input to the remedial action planning for the site that is currently underway. 7 refs., 6 figs., 3 tabs

  16. Vitrification of radioactive contaminated soil by means of microwave energy

    Science.gov (United States)

    Yuan, Xun; Qing, Qi; Zhang, Shuai; Lu, Xirui

    2017-03-01

    Simulated radioactive contaminated soil was successfully vitrified by microwave sintering technology and the solidified body were systematically studied by Raman, XRD and SEM-EDX. The Raman results show that the solidified body transformed to amorphous structure better at higher temperature (1200 °C). The XRD results show that the metamictization has been significantly enhanced by the prolonged holding time at 1200 °C by microwave sintering, while by conventional sintering technology other crystal diffraction peaks, besides of silica at 2θ = 27.830°, still exist after being treated at 1200 °C for much longer time. The SEM-EDX discloses the micro-morphology of the sample and the uniform distribution of Nd element. All the results show that microwave technology performs vitrification better than the conventional sintering method in solidifying radioactive contaminated soil.

  17. Sites in the United States contaminated with radioactivity

    International Nuclear Information System (INIS)

    Wolbarst, A.B.; Blom, P.F.; Chan, D.

    1999-01-01

    Over the century that radioactive materials have been mined, processed, produced, and utilized, many sites across the US have become contaminated. Such sites include bases and installations of the Department of Defense, weapons production and research facilities of the Department of Energy, properties under the authority of other Federal agencies, privately-owned and governmental facilities that are licensed by the Nuclear Regulatory Commission and its Agreement States, and sites licensed by or the responsibility of states. This review reports on aspects of work by the Environmental Protection Agency, the Department of Defense, the Department of Energy, the Nuclear Regulatory Commission, and others to identify sites contaminated with radioactive materials. It also describes the principal programs that have been instituted to deal with them

  18. Disposal sheet for preventing scattering of radioactive contaminated material

    International Nuclear Information System (INIS)

    Miyasaka, Shun-ichi; Kurioka, Hitoshi; Nakamura, Kenjiro.

    1990-01-01

    Upon disposal of vinyl sheets at the final stage of dismantling operation for nuclear buildings, etc., radioactive contaminated materials caused by cutting concretes, etc. remain on the sheets. In view of the above, members capable of restoring original shape due to the temperature difference are attached to the sheet main body so that the sheet main body may be folded into a bag-like shape. Since the members as described above are bent upon temperature elevation in the sheets, the sheet main body is pulled by the members and then spontaneously folded into a bag-like shape. As a result, the radioactive contaminated materials remaining on the sheets are wrapped into the sheet main body free from touch to operator's hands or without scattering to the surrounding. This can prevent operator's external and internal exposure. (T.M.)

  19. Radioactive waste and contamination in the former Soviet Union

    International Nuclear Information System (INIS)

    Suokko, K.; Reicher, D.

    1993-01-01

    Decades of disregard for the hazards of radioactive waste have created contamination problems throughout the former Soviet Union rivaled only by the Chernobyl disaster. Although many civilian activities have contributed to radioactive waste problems, the nuclear weapons program has been by far the greatest culprit. For decades, three major weapons production facilities located east of the Ural Mountains operated in complete secrecy and outside of environmental controls. Referred to until recently only by their postal abbreviations, the cities of Chelyabinsk-65, Tomsk-7, and Krasnoyarsk-26 were open only to people who worked in them. The mismanagement of waste at these sites has led to catastrophic accidents and serious releases of radioactive materials. Lack of public disclosure, meanwhile, has often prevented proper medical treatment and caused delays in cleanup and containment. 5 refs

  20. Hanford tank residual waste - Contaminant source terms and release models

    International Nuclear Information System (INIS)

    Deutsch, William J.; Cantrell, Kirk J.; Krupka, Kenneth M.; Lindberg, Michael L.; Jeffery Serne, R.

    2011-01-01

    Highlights: → Residual waste from five Hanford spent fuel process storage tanks was evaluated. → Gibbsite is a common mineral in tanks with high Al concentrations. → Non-crystalline U-Na-C-O-P ± H phases are common in the U-rich residual. → Iron oxides/hydroxides have been identified in all residual waste samples. → Uranium release is highly dependent on waste and leachant compositions. - Abstract: Residual waste is expected to be left in 177 underground storage tanks after closure at the US Department of Energy's Hanford Site in Washington State, USA. In the long term, the residual wastes may represent a potential source of contamination to the subsurface environment. Residual materials that cannot be completely removed during the tank closure process are being studied to identify and characterize the solid phases and estimate the release of contaminants from these solids to water that might enter the closed tanks in the future. As of the end of 2009, residual waste from five tanks has been evaluated. Residual wastes from adjacent tanks C-202 and C-203 have high U concentrations of 24 and 59 wt.%, respectively, while residual wastes from nearby tanks C-103 and C-106 have low U concentrations of 0.4 and 0.03 wt.%, respectively. Aluminum concentrations are high (8.2-29.1 wt.%) in some tanks (C-103, C-106, and S-112) and relatively low ( 2 -saturated solution, or a CaCO 3 -saturated water. Uranium release concentrations are highly dependent on waste and leachant compositions with dissolved U concentrations one or two orders of magnitude higher in the tests with high U residual wastes, and also higher when leached with the CaCO 3 -saturated solution than with the Ca(OH) 2 -saturated solution. Technetium leachability is not as strongly dependent on the concentration of Tc in the waste, and it appears to be slightly more leachable by the Ca(OH) 2 -saturated solution than by the CaCO 3 -saturated solution. In general, Tc is much less leachable (<10 wt.% of the

  1. Radioactive contamination of environment and food in Poland in 1998

    International Nuclear Information System (INIS)

    Grabowski, D.; Kurowski, W.; Muszynski, W.; Rubel, B.; Smagala, G.; Swietochowska, J.

    1999-01-01

    The analysis of the level of radioactive contamination in environmental and food samples was carried out in Poland in 1998. The results were compared to the data from the period 1985-1997. Since the Chernobyl accident gradual decrease of contamination level has been observed. The gamma dose rate and the contamination of air, fallout, tape and surface water were at the level of 1985. The only contamination enhanced in relation to pre-Chernobyl period was the content of cesium isotopes in soil and as a consequence food contamination was higher particularly milk and meat. At present, the source of additional dose is ingestion of artificial isotopes with food as a result of food contamination. No significant regional differences in the distribution of the level of cesium in food over the territory of Poland has been registered. Milk can be assumed as the main contributor of cesium to the diet, its share is about 33% of annual intake of cesium. The average effective dose, resulting from the contaminated food consumption, was estimated to be at the level of 13 μSv per capita of the Polish population in 1998. (author)

  2. Radioactive contamination of environment and food in Poland in 1997

    International Nuclear Information System (INIS)

    Grabowski, D.; Kurowski, W.; Muszynski, W.; Rubel, B.; Smagala, G.; Swietochowska, J.; Wilgos, J.

    1998-01-01

    The analysis of the level of radioactive contamination in environmental and food samples was carried out in Poland in 1997. The results were compared to the data from the period 1985-1996. Since the Chernobyl accident gradual decrease of contamination level has been observed. The gamma dose rate and the contamination of air, fallout, tape and surface water were at the level of 1985. The only contamination enhanced in relation to pre-Chernobyl period was the content of cesium isotopes in soil and as a consequence food contamination was higher particularly milk and meat. At present, the source of additional dose is ingestion of artificial isotopes with food as a result of food contamination. No significant regional differences in the distribution of the level of cesium in food over the territory of Poland has been registered. Milk can be assumed as the main contributor of cesium to the diet, its share is about 35% of annual intake of cesium. The average effective dose equivalent, resulting from the contaminated food consumption, was estimated to be at the level of 13 μSv per capita of the Polish population in 1997. (author)

  3. Radioactive contamination of environment and food in Poland in 1996

    International Nuclear Information System (INIS)

    Grabowski, D.; Kurowski, W.; Muszynski, W.; Rubel, B.; Smagala, G.; Swietochowska, J.; Wilgos, J.

    1997-01-01

    The analysis of the level of radioactive contamination in environmental and food samples was carried out in Poland in 1996. The results were compared to the data from the period 1985-1995. Since the Chernobyl accident gradual decrease of contamination level has been observed. The gamma dose rate and the contamination of air, fallout, tape and surface water were at the level of 1985. The only contamination enhanced in relation to pre-Chernobyl period was the content of cesium isotopes in soil and as a consequence food contamination was higher particularly milk and meat. At present, the source of additional dose is ingestion of artificial isotopes with food as a result of food contamination. No significant regional differences in the distribution of the level of cesium in food over the territory of Poland has been registered. Milk can be assumed as the main contributor of cesium to the diet, its share is about 40% of annual intake of cesium. The average effective dose equivalent, resulting from the contaminated food consumption, was estimated to be at the level of 14 μSv per capita of the Polish population in 1996. (author)

  4. Radioactive contamination: atlas France and Europe. French soils contamination by Chernobyl accident fallouts - The lie evidences

    International Nuclear Information System (INIS)

    Paris, Andre; Castanier, Corinne

    2002-01-01

    This document deals with the Chernobyl nuclear accident impacts and the authorities transparency. The first part is a reference document constituted by the CRIIRAD and showing how the authorities strove for minimizing the real contamination of French soils by the Chernobyl fallouts. In the second part, an atlas provides the detailed maps of the radioactive contamination of soils based on more than 3000 measurements carried out by a geologist, Andre Paris, assisted by the CRIIRAD laboratory

  5. Radioactive releases from a thorium-contaminated site in Wayne, New Jersey

    International Nuclear Information System (INIS)

    Wang, J.; Yang, J.; Merry-Libby, P.

    1985-01-01

    Various residues and wastes from the production of thorium and rare earths from monazite ore are buried on a hillside in Wayne, New Jersey. In addition, contaminated materials (primarily soils) from nearby vicinity properties are being consolidated onto the Wayne site. The US Department of Energy plans to stabilize all the contaminated materials on an interim basis (20 years) until funding is available to remove them to another location. In order to evaluate the effectiveness of interim stabilization measures, pre-remedial action radioactive releases are compared to estimated releases under a reference stabilization option (one meter of soil cover). Two potential pathways are examined: (1) airborne radioactive gases (thoron and radon) and particulates, and (2) seepage into the near-surface groundwater. The relative reduction of releases into the air and groundwater for the reference stabilization option is analyzed using mathematical models for radioactive gas fluxes and atmospheric dispersion as well as groundwater transport and dispersion. The consequent health implications for nearby individuals and the general population are also estimated. Health effects due to radioactive releases are estimated to be insignificant

  6. Applicability of monitored natural attenuation at radioactively contaminated sites

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2006-01-15

    The IAEA attaches great importance to the dissemination of information that can assist Member States with the development, implementation, maintenance and continuous improvement of systems, programmes and activities that support a sustainable nuclear fuel cycle and nuclear applications, including managing the legacy of past practices and accidents. Hence, the IAEA has initiated a comprehensive programme of work covering all aspects of environmental remediation including: - Technical and non-technical factors influencing decision making in environmental remediation; - Site characterization techniques and strategies; - Assessment of remediation technologies; - Assessment of technical options for cleanup of contaminated media; - Post-restoration compliance monitoring; - Assessment of the costs of remediation measures. It has been observed that many measures to remove or contain contamination are inefficient below certain concentrations, in general costly, and of a limited lifetime compared with the half-lives of the radionuclides concerned. Dispersed low level contamination poses a particular challenge to those charged with its remediation. Economic considerations in many Member States also result in constraints being placed on resources available to deal with such contamination. Experience has also shown that many techniques are not efficient below certain concentration thresholds or may entail impacts on certain environmental compartments in addition to those due to the contamination itself. This includes doses received by workers on the remediation project. As a result, the concept of relying on geological media to retain contaminants and/or to 'flatten out' concentration/dose peaks is increasingly being discussed in a remediation context. Technical Reports Series No. 424 (Remediation of Sites with Dispersed Radioactive Contamination) examined a variety of technological options for remediating dispersed contamination and concluded that the approaches can be broadly

  7. Applicability of monitored natural attenuation at radioactively contaminated sites

    International Nuclear Information System (INIS)

    2006-01-01

    The IAEA attaches great importance to the dissemination of information that can assist Member States with the development, implementation, maintenance and continuous improvement of systems, programmes and activities that support a sustainable nuclear fuel cycle and nuclear applications, including managing the legacy of past practices and accidents. Hence, the IAEA has initiated a comprehensive programme of work covering all aspects of environmental remediation including: - Technical and non-technical factors influencing decision making in environmental remediation; - Site characterization techniques and strategies; - Assessment of remediation technologies; - Assessment of technical options for cleanup of contaminated media; - Post-restoration compliance monitoring; - Assessment of the costs of remediation measures. It has been observed that many measures to remove or contain contamination are inefficient below certain concentrations, in general costly, and of a limited lifetime compared with the half-lives of the radionuclides concerned. Dispersed low level contamination poses a particular challenge to those charged with its remediation. Economic considerations in many Member States also result in constraints being placed on resources available to deal with such contamination. Experience has also shown that many techniques are not efficient below certain concentration thresholds or may entail impacts on certain environmental compartments in addition to those due to the contamination itself. This includes doses received by workers on the remediation project. As a result, the concept of relying on geological media to retain contaminants and/or to 'flatten out' concentration/dose peaks is increasingly being discussed in a remediation context. Technical Reports Series No. 424 (Remediation of Sites with Dispersed Radioactive Contamination) examined a variety of technological options for remediating dispersed contamination and concluded that the approaches can be broadly

  8. Treatment, as radio-active waste, of large pieces of ∝-contaminated apparatus (1962)

    International Nuclear Information System (INIS)

    Boutot, P.; Capitaine, A.; Giachetto, I.

    1962-01-01

    Two solutions have been adopted: - removal of the material from its original container, treatment in a special container; - treatment of the material directly inside its original protective packing. The treatment of a fluorination oven illustrates the second process. After a thorough cleaning of the enclosure, the oven is fixed in and the contamination held in place by a varnish. The assembly is placed in a special container and covered with shaken-down concrete. The container is shut by means of a welded cover. The operations are carried out under reduced pressure. At the end of this process it is impossible to detect any residual radioactivity. (authors) [fr

  9. Standard Guide for Unrestricted Disposition of Bulk Materials Containing Residual Amounts of Radioactivity

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2009-01-01

    1.1 This guide covers the techniques for obtaining approval for release of materials encountered in decontamination and decommissioning (D&D) from restricted use. This would be addressed in the decommissioning plan (E 1281). It applies to materials that do not meet any of the requirements for regulatory control because of radioactivity content. Fig. 1 shows the logic diagram for determining the materials that could be considered for release. Materials that negotiate this logic tree are referred to as “candidate for release based on dose.” 1.2 The objective of this guide is to provide a methodology for distinguishing between material that must be carefully isolated to prevent human contact from that that can be recycled or otherwise disposed of. It applies to material in which the radioactivity is dispersed more or less uniformly throughout the volume of the material (termed residual in bulk form) as opposed to surface contaminated objects. 1.3 Surface contaminated objects are materials externally co...

  10. Waste processing system for product contaminated with radioactivity

    International Nuclear Information System (INIS)

    Sotoyama, Koichi; Takaya, Jun-ichi; Takahashi, Suehiro.

    1987-01-01

    Purpose: To enable to processing contaminated products while separating them into metals at high contamination level and non-metals at low contamination level. Constitution: Pulverized radioactive wastes conveyed on a conveyor belt are uniformly irradiated by a ring-illumination device and then they are picked-up by a television camera or the like. The picked-up signals are sent to an image processing device, applied with appropriate binarization and metal objects are separated by utilizing the light absorbing property of non-metal and light reflection property of metals. The graviational center for the metal object is calculated from the binarized image, the positional information is provided to a robot controller and the metal object is transferred to another position by a robot. Since only the metal object at high radioactive contamination level can be taken out separately, it is no more necessary to process the entire wastes as the high level decontamination products, to thereby provide an economical advantage. (Sekiya, K.)

  11. The accumulation of radioactive contaminants in drinking water distribution systems.

    Science.gov (United States)

    Lytle, Darren A; Sorg, Thomas; Wang, Lili; Chen, Abe

    2014-03-01

    The accumulation of trace contaminants in drinking water distribution system sediment and scales has been documented, raising concerns that the subsequent release of the contaminants back to the water is a potential human exposure pathway. Radioactive contaminants are of concern because of their known health effects and because of their persistence within associated distribution system materials. The objective of this work was to measure the amount of a number of radioactive contaminants (radium, thorium, and uranium isotopes, and gross alpha and beta activity) in distribution solids collected from water systems in four states (Wisconsin, Illinois, Minnesota, and Texas). The water utilities chosen had measurable levels of radium in their source waters. In addition, 19 other elements in the solids were quantified. Water systems provided solids primarily collected during routine fire hydrant flushing. Iron was the dominant element in nearly all of the solids and was followed by calcium, phosphorus, magnesium, manganese, silicon, aluminum and barium in descending order. Gross alpha and beta radiation averaged 255 and 181 pCi/g, and were as high as 1602 and 1169 pCi/g, respectively. Total radium, thorium and uranium averaged 143, 40 and 6.4 pCi/g, respectively. Radium-226 and -228 averaged 74 and 69 pCi/g, and were as high as 250 and 351 pCi/g, respectively. Published by Elsevier Ltd.

  12. Ways for forestry management in radioactive contamination zone

    International Nuclear Information System (INIS)

    Kaletnik, N.N.; Pasternak, P.S.; Kiselevskij, R.G.; Molotkov, P.I.; Kuchma, N.D.; Landin, V.P.; Matukhno, Yu.D.; Shlonchak, G.L.; Podkur, P.P.; Khudolej, V.I.

    1989-01-01

    The necessity of realization of forestry protection measures in the radioactive contamination zone is determined by the forest ecological part and the problems of elimination of the territory secondary contamination in the process of radionuclide migration. The damage of forest tracts in the zone is analyzed. The data on pine surface contamination levels, needles appearance in forests with different degree of damage and crown phytomass, growth for pines 20 years old in forests with different damage degrees are considered. The index of pine forest state is obtained. The data discussed reveal the complicated situation, which takes place in the 30-km zone forests. It is shown that the depth of radionuclide migration into soil for forest areas is twice lower as compared with that for open places. 6 tabs

  13. Report on residual radioactive materials on public or acquired lands of the United States

    Energy Technology Data Exchange (ETDEWEB)

    None

    1979-07-01

    This report identifies sites located on public or acquired lands of the United States containing residual radioactive materials and other radioactive waste (excluding waste resulting from the production of electric energy) and was developed in accordance with the provisions of Section 114(b) of Public Law 95-604, "Uranium Mill Tailings Radiation Control Act of 1978," enacted on November 8, 1978. Additionally, the report specifies which Federal agency has jurisdiction over such sites and, where appropriate data were available, provides a description of the radiological status of each of the sites reported. For purpose of providing a timely report t o t h e Congress, a termination date of May 31, 1979 was established for the receipt, correlation, and analysis of the input data. As of this date, residual radioactive materials and other radioactive waste have been identified by six Federal agencies at 48 sites throughout the United States. Table 1 on page vi provides a summary listing of the number of sites under the jurisdiction of each of these reporting agencies. A cross listing in tabular form by affected state is presented in Table 2 on page viii. Of the 48 sites reported, 36 are located i n three western states - Colorado (27 sites), Wyoming (5 sites), and Utah (4 sites). Based upon t h e data submitted, the sites were categorized into three broad radiological status categories -- controlled, unstabilized, and risk to the public. At controlled sites, the residue is stabilized, access t o t h e site is controlled, the s i t e is well monitored, and does not currently constitute a risk to the public. At sites in the unstabilized category, a probability exists for the spread of contamination. Sites in the risk category contain residue which represents a long-term risk to the public under present conditions. Of the 48 reported sites,. 9 (approximately 19%) could be classified in the controlled category; 38 (approximately 79%) were in the unstabilized category and

  14. Measurement of radioactive soil contamination from the air

    International Nuclear Information System (INIS)

    Loman, A.C.; Kuile, C.R. ter; Slaper, H.

    1990-09-01

    In-situ gamma spectrometry can be used to determine the qualitative and quantitative deposition of radioactive materials on the ground surface. By applying the in-situ spectrometry method using either a helicopter or an airplane, large areas can be scanned in a short period of time. In this report the results of in-situ gamma spectroscopic measurements taken from a helicopter are described. Measurements were carried out using a single point source, a field of 36 point sources, and using the present ground contamination due to fall-out from the Chernobyl accident and atom bombs. The results of these measurements were used to determine calibration factors, which were in agreement with a calibration obtained using more simple (and less expensive) laboratory measurements in combination with flux calculations. Detection limits for the measurement of surface contamination were determined. At a height of 50 meters above the surface and using a measurement time of 2 minutes, the minimally detectable surface contamination was 1.1 kBqm -2 for a Cs-137 contamination and 2.1 kBqm -2 for I-131 contamination. Fall-out determinations based on measurements taken at a height of 50 meters were in agreement with determinations taken at a height of 1 meter, and with the results obtained measuring soil samples. The in-situ gamma spectroscopy, using helicopter or airplane, is a fast and powerful method for mapping surface contamination. (author). 13 refs.; 18 figs.; 13 tabs

  15. Control levels for residual contamination in materials considered for recycle and reuse

    International Nuclear Information System (INIS)

    Hill, R.L.; Aaberg, R.L.; Baker, D.A.; Kennedy, W.E. Jr.

    1993-09-01

    Pacific Northwest Laboratory (PNL) is collecting data and conducting technical analyses to support joint efforts by the U.S. Department of Energy (DOE), Office of Environmental Guidance, Air, Water and Radiation Division (DOE/EH-232); by the U.S. Environmental Protection Agency (EPA); and by the U.S. Nuclear Regulatory Commission (NRC) to develop radiological control criteria for the recycle and reuse of scrap materials and equipment that contain residual radioactive contamination. The initial radiological control levels are the concentrations in or on materials considered for recycle or reuse that meet the individual (human) or industrial (electronics/film) dose criteria. The analysis identifies relevant radionuclides, potential mechanisms of exposure, and methods to determine possible non-health-related impacts from residual radioactive contamination in materials considered for recycle or reuse. The generic methodology and scenarios described here provide a basic framework for numerically deriving radiological control criteria for recycle or reuse. These will be adequately conservative for most situations

  16. Residual radioactivity in the soil of the Semipalatinsk Nuclear Test Site in the former USSR

    International Nuclear Information System (INIS)

    Yamamoto, Masayoshi; Tsukatani, Tsuneo; Katayama, Yukio

    1996-01-01

    This paper deals with our efforts to survey residual readioactivity in the soil sampled at teh Semipalatinsk Nuclear Test Site and at off-site areas in Kazakhstan. The soil sampled at the hypocenter where the first Soviet nuclear explosion was carried out on 29 August 1949, and at the bank of the crater called open-quotes Bolapan,close quotes which was formed by an underground nuclear detonation on 15 January 1965 along the Shagan River. As a comparison, other soil was also sampled in the cities of Kurchatov and Almaty. These data have allowed a preliminary evaluation of the contemporary radioactive contamination of the land in and around the test site. At the first nuclear explosion site and at Bolapan, higher than background levels of 239,240 Pu with weapons-grade plutonium were detected together with fission and activation products such as 137 Cs, 60 Co, 152 Eu, and 154 Eu. 20 refs., 3 figs., 5 tabs

  17. Demonstration of a computer model for residual radioactive material guidelines, RESRAD

    International Nuclear Information System (INIS)

    Yu, C.; Yuan, Y.C.; Zielen, A.J.; Wallo, A. III

    1989-01-01

    A computer model was developed to calculate residual radioactive material guidelines for the US Department of Energy (DOE). This model, called RESRAD, can be run on IBM or IBM-compatible microcomputer. Seven potential exposure pathways from contaminated soil are analyzed, including external radiation exposure and internal radiation exposure from inhalation and food digestion. The RESRAD code has been applied to several DOE sites to derive soil cleanup guidelines. The experience gained indicates that a comprehensive set of site-specific hydrogeologic and geochemical input parameters must be used for a realistic pathway analysis. The RESRAD code is a useful tool; it is easy to run and very user-friendly. 6 refs., 12 figs

  18. Latest movements associated with radioactive contamination and disaster waste management

    International Nuclear Information System (INIS)

    Omura, Tomomi

    2012-01-01

    As for the radioactive contamination countermeasures taken for the accident of the Fukushima Daiichi Nuclear Station of Tokyo Electric Power Company, this paper introduces in the digest version the following movements from early March to early April 2012. (1) Organizational structure. Inauguration of Nuclear Regulatory Agency, and the organizational structure of Fukushima Environment Regeneration Office of the Ministry of the Environment. (2) The Act on Special Measures concerning the Handling of Radioactive Pollution. Publication by the Ministry of the Environment on decontamination plan for three municipalities belonging to Special Decontamination Area, decontamination plan for Intensive Contamination Survey Area, new construction of disposal sites for designated waste with the level exceeding 8,000 Bq / kg, and disaster waste direct treatment project and substitute treatment project in Fukushima Prefecture. (3) Radiation exposure countermeasures. Lawmaker-initiated registration plan by Democratic Party, Liberal Democratic Party, and New Komeito. (4) Technological evaluation. Publication of the results of Decontamination Technology Demonstration Test Projects by the Cabinet Office, the Ministry of the Environment, and Fukushima Prefecture. (5) Monitoring. Full-scale implementation of radioactivity monitoring plan in Tokyo Bay in Fiscal 2012. (6) Disaster waste countermeasures. Request of the government to the local governments on the wide-area treatment of wreckage, active request to the Cement Association in cooperation with the treatment of wreckage, and positive replies from of 22 prefectures / cities regarding the acceptance of wide-area wreckage treatment. (O.A.)

  19. A method for determining allowable residual contamination levels of radionuclide mixtures in soil

    International Nuclear Information System (INIS)

    Napier, B.A.

    1982-05-01

    An important consideration in the disposal of radioactive wastes, and consequently in the preparation of plans for remedial actions at contaminated sites, is the amount of radioactive contamination that may be allowed to remain at any particular waste site. The allowable residual contamination level (ARCL) is dependent on the radiation dose limit imposed, the physical and environmental characteristics of the waste site, and the time at which exposure to the wastes is assumed to occur. The steps in generating an ARCL are generally as follows: (1) develop plausible, credible site-specific exposure scenario; (2) calculate maximum annual radiation doses to an individual for each radionuclide based on the existing physical characteristics of the waste site and the site-specific exposure scenario; (3) calculate the ARCL for the dose limit desired, including all radionuclides present, uncorrected for site cleanup or barrier considerations; and (4) apply any corrections for proposed cleanup activity or addition of barriers to waste migration or uptake to obtain the ARCL applicable to the proposed action. Use of this method allows appropriate application of resources to achieve uniform compliance with a single regulatory standard, i.e., a radiation dose rate limit. Application and modification of the ARCL method requires appropriate models of the environmental transport and fate of radionuclides. Example calculations are given for several specific waste forms and waste site types in order to demonstrate the technique and generate comparisons with other approaches

  20. Characterization of radioactively contaminated sites for remediation purposes

    International Nuclear Information System (INIS)

    1998-05-01

    Characterization of the contaminated site is essential before embarking on a programme for its remediation and ultimate restoration. Reliable and suitable data must be obtained regarding the distribution and physical, chemical and nuclear properties of all radioactive contaminants. Characterization data is necessary for assessing the associated radiation risks and is used in support of the required engineering design and project planning for the environmental restoration. In addition, continuing characterization can provide information regarding efficiency of the cleanup methods and influence possible redirection of work efforts. Similarly, at the end of the remediation phase, characterization and ongoing monitoring can be used to demonstrate completion and success of the cleanup process. The suggested methodology represents a contribution attempting to solve the issue of preremediation characterization in a general manner. However, a number of difficulties might make this methodology unsuitable for general application across the diverse social, environmental and political systems in the IAEA Member States. This TECDOC covers the methodologies used to characterize radioactively contaminated sites for the purpose of remediating the potential sources of radiation exposure and assessing the hazards to human health and the environment

  1. Processing method for contaminated water containing radioactive waste

    International Nuclear Information System (INIS)

    Tahara, Toshiaki; Fukagawa, Ken-ichiro.

    1994-01-01

    For absorbing contaminated water containing radioactive substances, a sheet is prepared by covering water absorbing pulps carrying an organic water absorbent having an excellent water absorbability is semi-solidified upon absorption water with a water permeable cloth, such as a non-woven fabric having a shape stability. As the organic water absorbent, a hydrophilic polymer which retains adsorbed water as it is used. In particular, a starch-grafted copolymer having an excellent water absorbability also for reactor water containing boric acid is preferred. The organic water absorbent can be carried on the water absorbing pulps by scattering a granular organic water absorbent to the entire surface of the water absorbing cotton pulp extended thinly to carry it uniformly and putting them between thin absorbing paper sheets. If contaminated water containing radioactive materials are wiped off by using such a sheet, the entire sheet is semi-solidified along with the absorption with no leaching of the contaminated water, thereby enabling to move the wastes to a furnace for applying combustion treatment. (T.M.)

  2. Melting-decontamination method for radioactive contaminated metals

    International Nuclear Information System (INIS)

    Uda, Tatsuhiko; Tsuchiya, Hiroyuki; Miura, Noboru; Iba, Hajime.

    1985-01-01

    Purpose: To eliminate uranium components remaining in metals even after the uranium-contaminated metals are melted. Method: Metal wastes contaminated with actinide element or its compound as nuclear fuel substance are melted in a crucible. Molten metals are fallen through a filter disposed at the bottom of the crucible into another receiving crucible. Uranium compounds are still left in the molten metal fallen in the receiving crucible. The residual uranium compounds are concentrated by utilizing the principle of the zone-refining process. That is, a displaceable local-heating heater is disposed to the receiving crucible, by which metals once solidified in the receiving crucible is again heated locally to transfer from solid to molten phase in a quasi-equibilized manner. In this way, by eliminating the end of the metal rod at which the uranium is segregated, the contaminating coefficient can be improved. (Ikeda, J.)

  3. Analysis of Food Contaminants, Residues, and Chemical Constituents of Concern

    Science.gov (United States)

    Ismail, Baraem; Reuhs, Bradley L.; Nielsen, S. Suzanne

    The food chain that starts with farmers and ends with consumers can be complex, involving multiple stages of production and distribution (planting, harvesting, breeding, transporting, storing, importing, processing, packaging, distributing to retail markets, and shelf storing) (Fig. 18.1). Various practices can be employed at each stage in the food chain, which may include pesticide treatment, agricultural bioengineering, veterinary drug administration, environmental and storage conditions, processing applications, economic gain practices, use of food additives, choice of packaging material, etc. Each of these practices can play a major role in food quality and safety, due to the possibility of contamination with or introduction (intentionally and nonintentionally) of hazardous substances or constituents. Legislation and regulation to ensure food quality and safety are in place and continue to develop to protect the stakeholders, namely farmers, consumers, and industry. [Refer to reference (1) for information on regulations of food contaminants and residues.

  4. Environmental review of options for managing radioactively contaminated carbon steel

    International Nuclear Information System (INIS)

    1996-10-01

    The U.S. Department of Energy (DOE) is proposing to develop a strategy for the management of radioactively contaminated carbon steel (RCCS). Currently, most of this material either is placed in special containers and disposed of by shallow land burial in facilities designed for low-level radioactive waste (LLW) or is stored indefinitely pending sufficient funding to support alternative disposition. The growing amount of RCCS with which DOE will have to deal in the foreseeable future, coupled with the continued need to protect the human and natural environment, has led the Department to evaluate other approaches for managing this material. This environmental review (ER) describes the options that could be used for RCCS management and examines the potential environmental consequences of implementing each. Because much of the analysis underlying this document is available from previous studies, wherever possible the ER relies on incorporating the conclusions of those studies as summaries or by reference

  5. Prevention and mitigation of groundwater contamination from radioactive releases

    International Nuclear Information System (INIS)

    1988-10-01

    This document gives basic information on potential pathways and mechanisms, by which radioactive materials from releases can reach man, and on modelling considerations to predict the behaviour of radioactive materials in the ground. The main objective is to present an overview of existing techniques for preventing the offsite releases of contaminants into the groundwater systems and techniques for mitigation of effects of such releases should they occur. The recommended techniques are fully applicable to any hazardous materials, such as organic liquids, and toxic materials or otherwise dangerous materials, the presence of which in the accessible biosphere can represent health risks as well as economic losses to the general public. 11 refs, 2 figs, 8 tabs

  6. Sources to radioactive contamination in Murmansk and Arkhangelsk counties

    International Nuclear Information System (INIS)

    Nilsen, T.; Boehmer, N.

    1994-02-01

    The report gives a general view of information gathered by the Bellona Foundation on the use of nuclear energy, as well as storage and processing of radioactive waste in the region. Information has been collected since 1989 through extensive field work in the Russian Federation. During the gathering of source material for the report, crucial importance has been attached to Russian sources encountered during the field work. The report intends to present a survey of the various sources of possible radioactive pollution, and the historical background for placing the sources in the region. As it appears from the report, the most significant contamination source is the military activity. The Bellona Foundation has made a point of describing the sources only on a technical base, and no attempts have been made to evaluate risks and consequences of conceivable accidents. 78 refs

  7. Health effects associated with exposure to radioactively contaminated gold rings

    International Nuclear Information System (INIS)

    Baptiste, M.S.; Rothenberg, R.; Nasca, P.C.; Janerich, D.T.; Stutzman, C.D.; Rimawi, K.; O'Brien, W.; Matuszek, J.

    1984-01-01

    This study was designed to assess the health risks associated with exposure to radioactively contaminated gold rings. A group of 135 exposed individuals, who were identified through a statewide jewelry screening program, were studied to determine the frequency of carcinoma and other skin problems on the ring finger. Severity of skin problems increased with increasing length of wear. Forty-one of the exposures were associated with mild to severe skin problems. Nine of the individuals studied were diagnosed as having histologically confirmed squamous cell carcinomas at the site of exposure. The incidence of skin cancer on the ring finger was eleven times that expected for men and forty-five times that expected for women. These data indicate that physicians who have patients with skin lesions of the ring finger should be aware of the possibility of exposure to a radioactive gold ring

  8. Measures against radioactive contamination due to Fukushima First Nuclear Power Plant accidents. Part 3. Removing and decontamination of contaminated soil

    International Nuclear Information System (INIS)

    Ishii, K.; Terakawa, A.; Matsuyama, S.

    2012-01-01

    We studied the structure of radioactive cesium distribution in soil and found the exponential dependence. This behavior could be explained theoretically. We developed a useful method to decontaminate the soil contaminated with radioactive cesium atoms. We applied our method to the contaminated school yards of elementary schools of Marumori town and decontaminated total area of about 7000 m"2. (author)

  9. Remediation Of Radioactive Contaminated Soil in Oil Fields

    International Nuclear Information System (INIS)

    Taha, A.A.; Hassib, G.M.; Ibrahim, Z.A.

    2011-01-01

    Radioactive contamination by naturally occurring radioactive materials (NORM) in evaporation pond has been evaluated. At several onshore oil field locations, the produced water is discharged to form artificial lagoons or ponds. Subsequently, the released waters drain to the ground leaving radioactive deposits associated with the soil that eventually require remedial action in accordance with radiation protection principles. The present study aims to investigate the remediation of contaminated soil in some oil fields and in this concern, two scenarios were proposed. The first scenario is studying the feasibility of using soil washing technique (a physical-chemical separation process) for removing radium-226 from the contaminated soil samples collected from an evaporating pond. The size/activity distribution analyses were carried out. The data obtained showed that almost 68 % of the investigated soil was coarse sand (≥ 300 μm), 28 % was medium and fine sand (≤300 μm and (≥75 μm) and only small fraction of 4 % was silt and clay (≤75 μm). A series of mild acids such as HCl and mild NaCl/HCl (chloride washing) were used for washing the investigated soil fractions. The obtained data showed that the coarse fraction ≥ 300 μm can be re mediated below a regulatory level of 1Bq/g. and the radium from this coarse fraction could be easily removed by screening and chloride washing. For the remediation of (≤ 300 μm and (≥ 75 μm soil fractions, a series of mild chloride washing experiments also showed that the chloride base (NaCl/HCl) was found to be potentially useful. However, there was a difficulty in achieving a low radium value in the fine (≥ 75 μm size fractions using chloride washing. The second scenario is to get rid of all contaminated soil and store it in a concrete basin through the program of radiological protection of personnel and environment. Preliminary gamma survey of contaminated soil showed that the significant area of the investigated

  10. Radioactive inventories and sources for contamination of the Kara Sea

    International Nuclear Information System (INIS)

    Bradley, D.J.; Jenquin, U.P.

    1995-01-01

    The focus of this paper is on detailing the magnitudes of the sources of radionuclides that may be available, or have already been released to the Ob and Yenisey river systems. The emphasis is on the amounts of radioactivity that have been discharged to the environment in the West Siberian Basin. This are potential source terms to the Kara Sea via the Ob and Yenisey rivers. Russian estimates of what has been discharged to the Barents and Kara Seas, including direct ocean discharges, are summarized to provide some perspective on contamination of the Kara Sea. 1 fig., 3 tabs

  11. Recycling of radioactively contaminated materials: Public policy issues

    International Nuclear Information System (INIS)

    Hocking, E.K.

    1994-01-01

    Recycling radioactively contaminated materials requires varying degrees of interaction among Federal regulatory agencies such as the Nuclear Regulatory Commission (NRC) and the Environmental Protection Agency (EPA), State governments and regulators, the public, and the Department of Energy. The actions of any of these parties can elicit reactions from the other parties and will raise issues that must be addressed in order to achieve a coherent policy on recycling. The paper discusses potential actions and reactions of Federal regulatory agencies (defined as NRC and EPA), the States, and the Department and the policy issues they raise

  12. Long-run consequences of radioactive contamination in agriculture

    International Nuclear Information System (INIS)

    Eriksson, Aa.

    1983-01-01

    Three papers dealing with the effect of released radioactivity on agricultural operations are presented. The risk of the radiation from 137 Cs is estimated and compased with 90 Sr. The transport of radionuclides in the soil of the district of Malmoehus is calculated and applied to the radiation doses by oral food intake. Calculations of radiation doses by external radiation are also presented and the procedures to prevent contamination of food are disscussed. The items were treated at a public hearing on the 11th of June 1981 (G.B.)

  13. Decontamination of radioactive contaminated protective wear using dry cleaning solvent

    International Nuclear Information System (INIS)

    Muthiah, Pushpa; Chitra, S.; Paul, Biplob

    2013-01-01

    Liquid waste generated by conventional decontamination of radioactive contaminated cotton protective wear using detergent affects the chemical treatment of the plant. To reduce the generation of aqueous detergent waste, dry cleaning of cotton protective wear, highly soiled with oil and grease towards decontamination was tried with organic solvents. Mineral turpentine oil (MTO) among various other organic solvents was identified as a suitable organic solvent. As MTO leaves characteristic odour on the cloth, various commercial fragrances for the removal of the odour were tried. Application of the optimised dry cleaning solvent and commercial fragrance was adopted in plant scale operation. (author)

  14. Status of environmental response efforts at radioactively contaminated sites in the united states air force installation restoration program

    International Nuclear Information System (INIS)

    Rowe, W.D. Jr.; McEntee, T.E. Jr.; Johnson, B.; Manning, L.

    1995-01-01

    The United States Air Force has identified approximately 170 radioactively contaminated sites at its domestic installations. These sites contain a variety of low level radioactive and mixed wastes and are classified as burial sites, landfills, buildings, and other disposal sites. Of these 170, approximately 70 are presently being evaluated under the Air Force Installation Restoration Program (IRP) in accordance with applicable laws and regulations. Removal and/or remedial actions have been taken at specific sites using site-specific residual radioactivity criteria. The remaining sites are either under investigation to determine the need for possible action or have been classified as response complete based on restricted or unrestricted future use. This paper describes past Air Force operations that generated radioactive waste materials; examines the current inventory of resulting radioactively contaminated sites in the Air Force IRP; reviews criteria used to evaluate sites for removal and/or remedial actions; provides summary information on actions taken at sites; and focuses on response actions and cleanup levels at two completed sites. The paper concludes with an assessment of outstanding issues relevant to the remediation of radioactively contaminated sites. (author)

  15. Radioactive contamination of ingredients used in sweets industry

    International Nuclear Information System (INIS)

    Bodnar, Jozsef

    1988-01-01

    On the basis of samples tested in 1983-1987, the activity concentrations relative to unit dry matter are 2,5-3,5-times higher in cocoa shell than in cocoa beans, but the samples have only a small overall radioactive contamination within the total β activity, the 40 K activity ratio in cocoa beans is 72%, in cocoa shells 79%. The respective ratio of 87 Rb can be 20% in the two samples. The activity concentration contribution of 90 Sr and 137 Cs contamination in cocoa beans and cocoa shells is together 2%. The data of the samples from different locations do not show any significant differences. In samples from 1986-1987 the increase of cesium activity concentration can be observed. (author)

  16. The inhalation of radioactive materials as related to hand contamination

    Energy Technology Data Exchange (ETDEWEB)

    Bailey, J.C.; Rohr, R.C.

    1953-09-15

    Tests performed to determine the hazard associated with the inhalation of radioactive materials as the result of smoking with contaminated hands indicate that for dry uranium compounds adhering to the palmar surfaces of the hands, approximately 1.0% of the material may be transferred to a cigarette, and that of this approximately 0.2% may appear in the smoke which is inhaled. Most of the contamination originally placed in a cigarette was found in the ash, and only 11% of the material was not recovered following burning; approximately half of this loss may be attributed to normal losses inherent in the analytical process, the recovery efficiency for which was found by supplementary experiments to be 95%.

  17. Preparation of technical support material for radioactively contaminated land

    International Nuclear Information System (INIS)

    2000-01-01

    The UK Government is considering the introduction of a regulatory regime to address the legacy of sites that are radioactively contaminated due to historical activities. The Department of the Environment, Transport and the Regions (DETR) consulted on the principles of this regime in 1998, although no specific plans are yet in place to introduce the regime. The consultation paper envisaged that the Environment Agencies would have a major role in regulating the investigation and assessment of potentially contaminated sites and, where appropriate, their remediation. This work was commissioned by the Environment Agency, with support from DETR and SNIFFER (Scottish and Northern Ireland Forum for Environmental Research) to provide information on the techniques available allow the Environment Agencies to fulfil their envisaged regulatory requirements, and to assist DETR in the preparation of Statutory Guidance. The work was carried out by Entec UK Ltd, in conjunction with the NRPB

  18. Radioactive contamination of aquatic ecosystems following the Chernobyl accident

    International Nuclear Information System (INIS)

    Kryshev, I.I.

    1995-01-01

    The dynamics of radioactive contamination of aquatic ecosystems (1986-1990) is considered on the basis of observational data in the near and distant zones of the Chernobyl fallout (the Chernobyl Nuclear Power Plant (CNPP) cooling pond, the Pripyat River, the Dnieper reservoirs, and the Kopor inlet of the Gulf of Finland). Radionuclide accumulation in aquatic biota is analyzed. The results obtained indicate that the radioecological conditions in the water bodies under investigation were in a state of non-equilibrium over a long period of time following the Chernobyl accident. Reduction in the 137 Cs concentration proceeded slowly in most of the aquatic ecosystems. The effect of trophic levels which consisted of increased accumulation of radiocaesium by predatory fish was observed in various parts of the contaminated area. (author)

  19. Map of radioactive contamination in mushrooms of Poland in 1991

    International Nuclear Information System (INIS)

    Mietelski, J.W.; Jasinska, M.; Kubica, B.; Kozak, K.; Macharski, P.

    1992-01-01

    Results from part of the Polish Government programme for forests radioactive contamination studies are presented. 278 samples of edible mushroom (Xerocomus badius) were analysed for radiocesium 137 Cs and 134 Cs) and 40 K using low-background gamma spectrometer with a germanium detector. Samples were collected from all districts of Poland in October 1991 by forest inspectors. In consequence maps of 137 Cs, 134 Cs and for 40 K concentration in ''Xerocomus badius'' are presented. The method of measurements is also presented. Large differences in radiocesium contamination levels are observed for various parts of the country. The higher radiocesium contamination level is observed in Czestochowa-Opole region. Maximum value for 137 Cs is equal to 157 kBq/kg d.m. and that for 134 Cs is equal to 16.3 kBq/kg d.m. The 40 K content level is nearly constant and equal to c.a. 1.3 kBq/kg d.m. Minimum values for caesium contamination were observed in the Bieszczady Mountains. The effective dose equivalent estimation due to the consumption of mushrooms is performed. The limits of ingestion amounts are calculated. (author). 15 refs, 15 figs, 6 tabs

  20. Process for affixing radioactive contamination on contaminated materials or wastes. Its application

    International Nuclear Information System (INIS)

    Aubouin, Guy; Aude, Georges; Tassigny, Christian de.

    1982-01-01

    The invention concerns a process for affixing radioactive contamination on materials or waste matter in order to ensure that the materials are transferred in complete safety or to package them when their activity is low. Under this process at least one coat of a resin polymerizable at ambient temperature, for example an epoxy resin, a polyester resin, a vinyl resin or a mixture of thermohardening resin and thermoplastic resin, is sprayed on to the contaminated material part by means of an electrostatic gun [fr

  1. Allowable residual-contamination levels for decommissioning facilities in the 100 areas of the Hanford Site

    International Nuclear Information System (INIS)

    Kennedy, W.E. Jr.; Napier, B.A.

    1983-07-01

    This report contains the results of a study sponsored by UNC Nuclear Industries to determine Allowable Residual Contamination Levels (ARCL) for five generic categories of facilities in the 100 Areas of the Hanford Site. The purpose of this study is to provide ARCL data useful to UNC engineers in conducting safety and cost comparisons for decommissioning alternatives. The ARCL results are based on a scenario/exposure-pathway analysis and compliance with an annual dose limit for three specific modes of future use of the land and facilities. These modes of use are restricted, controlled, and unrestricted. The information on ARCL values for restricted and controlled use provided by this report is intended to permit a full consideration of decommissioning alternatives. ARCL results are presented both for surface contamination remaining in facilities (in dpm/100 cm 2 ), and for unconfined surface and confined subsurface soil conditions (in pCi/g). Two confined soil conditions are considered: contamination at depths between 1 and 4 m, and contamination at depths greater than or equal to 5 m. A set of worksheets are presented in an appendix for modifying the ARCL values to accommodate changes in the radionuclide mixture or concentrations, to consider the impacts of radioactive decay, and to predict instrument responses. Finally, a comparison is made between the unrestricted release ARCL values for the 100 Area facilities and existing decommissioning and land disposal regulations. For surface contamination, the comparison shows good agreement. For soil contamination, the comparison shows good agreement if reasonable modification factors are applied to account for the differences in modeling soil contamination and licensed low-level waste

  2. Mapping the radioactive contamination in urban environments after nuclear emergencies

    International Nuclear Information System (INIS)

    Kaiser, Jan Christian; Proehl, Gerhard; Woda, Clemens

    2008-01-01

    Full text: In the event of a nuclear emergency in an urban environment a reliable overview on the radioactive contamination is crucial for decision making. To assess the radiological situation both measurements of the gamma dose or dose rate (GDR) and results from urban dispersion and deposition models are used. Measurements may arrive from various sources like car-borne detectors or man-borne radiation-sensitive materials embedded in cell phones, flash memory devices or RFID chips. The measurements depend strongly on the detector environment. To account for this dependence each signal is multiplied by a location factor, which quantifies the deviation of the recorded signal from the hypothetical signal of a reference surface of infinitely extended lawn. Furthermore, the data originate from geo-referenced points or lines but do not provide full spatial information. We present here two approaches to produce maps of the reference GDR or surface contamination in urban areas, which are implemented in the Inhabited Areas Monitoring Module (IAMM) as part of the European decision support systems RODOS and ARGOS. Immediately after the accident, a few measurements are combined with the predictions of urban models using data assimilation. If enough measurements are available they are regionalised with geo-statistical interpolation algorithms like inverse distance weighting or kriging. Both approaches are demonstrated in hypothetical scenarios based on the explosion of a radioactive dispersion device. (author)

  3. Strategies for the management of radioactively contaminated sites

    International Nuclear Information System (INIS)

    Butter, K. R.; Fellingham, L. R.; Holdroyd, S. D.; Smith-Briggs, J. L.

    1997-01-01

    The rehabilitation of radioactively contaminated land is a small but growing field of activity. Worldwide the activity has been dominated by the rehabilitation of uranium mining and milling sites and areas affected by major nuclear accidents, such as Chernobyl and Khystym. To date most of the sites in or associated with the UK have been small in scale and have generally involved natural radionuclides. However, with the decommissioning of large areas of many old nuclear industry sites and those associated with the development and production of nuclear weapons and the operations of nuclear submarines, the scale of these operations is set to rise very significantly. This paper addresses key considerations in managing the rehabilitation of radioactively contaminated sites. It illustrates their significance through examples ranging in scale from a few hectares to tens of thousands of square kilometres. The first example deals with a former waste storage and processing area at Harwell Laboratory. The second covers a risk reduction rehabilitation programme at the former British nuclear weapons test site at Maralinga in Australia. The third assesses the potential for cost-effective countermeasures to reduce aggregate doses received outside the 30 km exclusion zone around the Chernobyl nuclear reactor site

  4. Release process for non-real property containing residual radioactive material

    International Nuclear Information System (INIS)

    Ranek, N.L.; Chen, S.Y.; Kamboj, S.; Hensley, J.; Burns, D.; Fleming, R.; Warren, S.; Wallo, A.

    1997-01-01

    It is DOE's objective to operate its facilities and to conduct its activities so that radiation exposures to members of the public are maintained within acceptable limits and exposures to residual radioactive materials are controlled. To accomplish this, DOE has adopted Order DOE 5400.51 'Radiation Protection of the Public and the Environment', and will be promulgating IO CR Part 834 to codify and clarify the requirements of DOE 5400.5. Under both DOE 5400.5 and 10 CR Part 834, radioactively contaminated DOE property is prohibited from release unless specific actions have been completed prior to the release. This paper outlines a ten-step process that, if followed, will assist DOE Operations and contractor personnel in ensuring that the required actions established by Order DOE 5400.5 and 10 CR Part 834 have been appropriately completed prior to the release for reuse or recycle of non-real property (e.g., office furniture, computers, hand tools, machinery, vehicles and scrap metal). Following the process will assist in ensuring that radiological doses to the public from the released materials will meet applicable regulatory standards and be as low as reasonably achievable (ALARA)

  5. Experimental study of contamination by inhalation of radioactive iodine aerosols. Biological balance

    International Nuclear Information System (INIS)

    Marble, G.

    1968-01-01

    Several articles have been published concerning research into contamination produced by inhalation of radioactive iodine aerosols in monkeys. Results dealing with the biological balance of this contamination are presented and discussed in this report. (author) [fr

  6. In-situ vitrification of radioactively contaminated soils: summary paper

    International Nuclear Information System (INIS)

    Buelt, J.L.; Fitzpatrick, V.F.

    1987-01-01

    The in-situ vitrification (ISV) process is a new technology that has been developed from its conceptual phase through selected field-scale application tests during the last six years. In situ vitrification converts contaminated soils and waste inclusions into a durable glass and crystalline waste form by in-place melting. Electrodes are inserted into the soil to be treated and an electrical current is passed through the soil to be treated and an electrical current is passed through the soil to melt it. After cooling, the process fixes (TRU) and fission product radionuclides making them relatively nonleachable, resistant to intrusion, and nondispersible when intentionally disturbed. Another application considered for isolation of radioactively contaminated soils, but not yet developed, is the generation of impermeable barrier walls to prevent ground water seepage into a site. The barrier technique could also be used over the surface of an existing disposal site to deter plant and animal intrusion. The development units have been extensively tested with many types of soils and waste inclusions such as concrete, buried metals, sealed containers, organic chemicals with high boiling points such as polychlorinated biphenyls, and inorganic chemicals, including toxic heavy metals, nitrates, and sulfates. Nitrates and organics are destroyed, while heavy metals and fluorides are retained to a high percentage within the molten soil during processing. At $200 to $300/m 3 for radioactive waste, the process is economically competitive with many alternative remediation processes. The ISV process has been developed to the point where it is ready for large-scale field testing at an actual TRU-contaminated soil site. 5 references, 2 figures, 2 tables

  7. Characteristics of radioactive contamination of vegetables derived from the Fukushima nuclear accident

    International Nuclear Information System (INIS)

    Shiba, Kazuhiro; Kitamura, Yoji; Kozaka, Takashi; Uno, Izumi; Shimizu, Kikuo; Hirota, Masahiro; Higaki, Shogo; Masumoto, Kazuyoshi

    2012-01-01

    We examined the characteristics of the radioactive contamination and the physical removal of radioactivity from contaminated cabbage and spinach. In a distribution imaging study, there were two types of contamination, spot type and spread type, of cabbage and spinach. The relative radioactivity (PSL) of the face of the leaf was much higher than that of the back of a leaf of cabbage. The ratio of relative radioactivity (PSL) between spot contamination and spread contamination in a leaf of spinach was 9.4% and 90.6%, respectively. More than 80% of radioactivity attaches to the surface of leaves of spinach. There was no significant difference of radioactivity removal between hand-washing and rinsing with running water. The degree of removal of radioactivity from contaminated spinach depended on the length of time between contamination and rinsing. When contaminated spinach was rinsed within 1 week after contamination, the removal ratio of 131 I and 137 Cs was high, with 50% and 70%, respectively. When rinsing contaminated spinaches more than 2 weeks after contamination, the removal ratio of 131 I and 137 Cs was low, approximately 34% and 69%, respectively. (author)

  8. Development of RadRob15, A Robot for Detecting Radioactive Contamination in Nuclear Medicine Departments

    Directory of Open Access Journals (Sweden)

    Shafe A.

    2016-09-01

    Full Text Available Accidental or intentional release of radioactive materials into the living or working environment may cause radioactive contamination. In nuclear medicine departments, radioactive contamination is usually due to radionuclides which emit high energy gamma photons and particles. These radionuclides have a broad range of energies and penetration capabilities. Rapid detection of radioactive contamination is very important for efficient removing of the contamination without spreading the radionuclides. A quick scan of the contaminated area helps health physicists locate the contaminated area and assess the level of activity. Studies performed in IR Iran shows that in some nuclear medicine departments, areas with relatively high levels of activity can be found. The highest contamination level was detected in corridors which are usually used by patients. To monitor radioactive contamination in nuclear medicine departments, RadRob15, a contamination detecting robot was developed in the Ionizing and Non-ionizing Radiation Protection Research Center (INIRPRC. The motor vehicle scanner and the gas radiation detector are the main components of this robot. The detection limit of this robot has enabled it to detect low levels of radioactive contamination. Our preliminary tests show that RadRob15 can be easily used in nuclear medicine departments as a device for quick surveys which identifies the presence or absence of radioactive contamination.

  9. Derivation of uranium residual radioactive material guidelines for the Elza Gate Site

    International Nuclear Information System (INIS)

    Cheng, J.J.; Yu, C.; Devgun, J.S.

    1991-02-01

    Residual radioactive material guidelines for uranium were derived for a large, homogeneously contaminated area at the Elza Gate Site in Oak Ridge, Tennessee. The derivation of the single-nuclide and total uranium guidelines was based on the requirement that the 50-year committed effective dose equivalent to hypothetical individual who lives or works in the immediate vicinity of the Elza Gate Site should not exceed a dose of 100 mrem/yr following decontamination. The DOE residual radioactive guideline computer code RESRAD was used in this evaluation. Four potential scenarios were considered for the site; the scenarios vary with regard to time spent at the site, sources of water used, and sources of food consumed. The results of the evaluation indicate that the basic dose limit of 100 mrem/yr will not be exceeded for uranium within 1000 years, provided that the soil concentration of uranium at the Elza Gate Site does not exceed the following levels: 1800 pCi/g for Scenario A (industrial worker: the expected scenario); 4000 pCi/g for Scenario B (recreationist: a plausible scenario); 470 pCi/g for Scenario C (resident farmer using pond water as the only water source: a possible but unlikely scenario); and 120 pCi/g for Scenario D (resident farmer using well water as the only water source: a possible but unlikely scenario). The uranium guideline applies to the total activity concentration of uranium isotopes in their natural activity concentration ratio of 1:1: 0.046. These guidelines are calculated on the basis of a dose of 100 mrem/yr. In setting the actual uranium guideline for the Elza Gate Site, the DOE will apply the as low as reasonably achievable (ALARA) policy to the decision-making process, along with other factors, such as determining whether a particular scenario is reasonable and appropriate. 10 refs., 3 figs., 7 tabs

  10. Decoding Environmental Processes Using Radioactive Isotopes for the Post-Radioactive Contamination Recovery Assessment

    Science.gov (United States)

    Yasumiishi, Misa; Nishimura, Taku; Osawa, Kazutoshi; Renschler, Chris

    2017-04-01

    The continual monitoring of environmental radioactive levels in Fukushima, Japan following the nuclear plant accident in March 2011 provides our society with valuable information in two ways. First, the collected data can be used as an indicator to assess the progress of decontamination efforts. Secondly, the collected data also can be used to understand the behavior of radioactive isotopes in the environment which leads to further understanding of the landform processes. These two aspects are inseparable for us to understand the effects of radioactive contamination in a dynamic environmental system. During the summer of 2016, 27 soil core samples were collected on a farmer's land (rice paddies and forest) in Fukushima, about 20 km northwest of the nuclear plant. Each core was divided into 2.0 - 3.0 cm slices for the Cs-134, Cs-137, and I-131 level measurement. The collected data is being analyzed from multiple perspectives: temporal, spatial, and geophysical. In the forest area, even on the same hillslope, multiple soil types and horizon depths were observed which indicates the challenges in assessing the subsurface radioactive isotope movements. It appears that although highly humic soils show higher or about the same level of radioactivity in the surface layers, as the depth increased, the radioactivity decreased more in those samples compared with more sandy soils. With regard to the direction a slope faces and the sampling altitudes, the correlation between those attributes and radioactivity levels is inconclusive at this moment. The altitude might have affected the fallout level on a single hillslope-basis. However, to determine the correlation, further sampling and the detailed analysis of vegetation and topography might be necessary. Where the surface soil was scraped and new soil was brought in, former rice paddy surface layers did show three-magnitude levels lower of radioactivity in the top layer when compared with forest soils. At the foot of forest

  11. Characterization and remediation of highly radioactive contaminated soil at Hanford

    International Nuclear Information System (INIS)

    Buckmaster, M.A.; Erickson, J.K.

    1993-09-01

    The Hanford Site, Richland, Washington, contains over 1,500 identified waste sites and numerous groundwater plumes that will be characterized and remediated over the next 30 years. As a result of the Hanford Federal Facility Agreement and Consent Order, the US Department of Energy (DOE) has initiated a remedial investigation/feasibility study (RI/FS) at the 200-BP-1 operable unit. The 200-BP-1 RI/FS is the first Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) investigation on the Hanford Site that involves highly radioactive and chemically contaminated soils. The initial phase of site characterization was designed to assess the nature and extent of contamination associated with the source waste sites within the 200-BP-1 operable unit. Characterization activities consisted of drilling and sampling, chemical and physical analysis of samples, and development of a conceptual vadose zone model. These data were then used. to develop remedial alternatives during the FS evaluation. The preferred alternative resulting from the RI/FS process for the 200-BP-1 operable unit is to construct a surface isolation barrier. The multi-layered earthen barrier will be designed to prevent migration of contaminants resulting from water infiltration, biointrusion, and wind and water erosion

  12. Inductively coupled plasma mass spectrometer installation modifications in a radioactive contaminated laboratory for the analysis of DOE radioactive waste streams

    International Nuclear Information System (INIS)

    Giaquinto, J.M.; Keller, J.M.; Meeks, A.M.

    1997-04-01

    The operation and maintenance of a complex analytical instrument such as an inductively coupled plasma mass spectrometer in a radioactive contaminated environment presents unique problems and challenges that have to be considered in the purchasing and installation process. Considerations such as vendor experience, typical radiation levels, sample matrices encountered during sample analysis, instrument accessibility for maintenance, and upkeep must be incorporated into the decision process. The Radioactive Materials Analytical Laboratory (RMAL) at Oak Ridge National Laboratory (ORNL) recently purchased and installed an inductively coupled plasma mass spectrometer for the analysis of Department of Energy (DOE) radioactive waste streams. This presentation will outline the purchasing decision, installation of the instrument, and how the modifications needed to operate in a radioactive contaminated laboratory do not significantly impact the daily operation and maintenance requirements of the instrument. Also, a contamination survey of the system will be presented which demonstrates the contamination levels in the instrument from the sample introduction system to the detector

  13. Inductively coupled plasma mass spectrometer installation modifications in a radioactive contaminated laboratory for the analysis of DOE radioactive waste streams

    International Nuclear Information System (INIS)

    Giaquinto, J.M.; Keller, J.M.; Meeks, A.M.

    1998-01-01

    The operation and maintenance of a complex analytical instrument such as an inductively coupled plasma mass spectrometer in a radioactive contaminated environment presents unique problems and challenges that have to be considered in the purchasing and installation process. Considerations such as vendor experience, typical radiation levels, sample matrices encountered during sample analysis, instrument accessibility for maintenance, and upkeep must be incorporated into the decision process. The Radioactive Materials Analytical Laboratory (RMAL) at Oak Ridge National Laboratory (ORNL) recently purchased and installed an inductively coupled plasma mass spectrometer for the analysis of Department of Energy (DOE) radioactive waste streams. This presentation will outline the purchasing decision, installation of the instrument, and how the modifications needed to operate in a radioactive contaminated laboratory do not significantly impact the daily operation and maintenance requirements of the instrument. Also, a contamination survey of the system will be presented which demonstrates the contamination levels in the instrument from the sample introduction system to the detector. (author)

  14. Treatment of heterogeneous mixed wastes: Enzyme degradation of cellulosic materials contaminated with hazardous organics and toxic and radioactive metals

    International Nuclear Information System (INIS)

    Vanderberg, L.A.; Foreman, T.M.; Attrep, M. Jr.; Brainard, J.R.; Sauer, N.

    1999-01-01

    The redirection and downsizing of the US Department of Energy's nuclear weapons complex requires that many facilities be decontaminated and decommissioned (D and D). At Los Alamos National Laboratory, much of the low-level radioactive, mixed, and hazardous/chemical waste volume handled by waste management operations was produced by D and D and environmental restoration activities. A combination of technologies--air stripping and biodegradation of volatile organics, enzymatic digestion of cellulosics, and metal ion extraction--was effective in treating a radiologically contaminated heterogeneous paint-stripping waste. Treatment of VOCs using a modified bioreactor avoided radioactive contamination of byproduct biomass and inhibition of biodegradation by toxic metal ions in the waste. Cellulase digestion of bulk cellulose minimized the final solid waste volume by 80%. Moreover, the residue passed TCLP for RCRA metals. Hazardous metals and radioactivity in byproduct sugar solutions were removed using polymer filtration, which employs a combination of water-soluble chelating polymers and ultrafiltration to separate and concentrate metal contaminants. Polymer filtration was used to concentrate RCRA metals and radioactivity into <5% of the original wastewater volume. Permeate solutions had no detectable radioactivity and were below RCRA-allowable discharge limits for Pb and Cr

  15. Restoration of environments with radioactive residues. Papers and discussions. Proceedings of an international symposium

    International Nuclear Information System (INIS)

    2000-01-01

    After the use of radioactive substances or the application of nuclear energy, radioactive residues may remain in the environment and may give rise to radiation exposure of people. Radioactive residues can originate from several sources. They may be remnants following the termination of a practice such as the decommissioning of a nuclear power plant. Occasionally, residues can derive from the accumulation of radionuclides from normal discharges to the environment of radioactive effluents from practices. Most commonly, they are the result of human activities that have been performed in the past without proper regard for the current international radiation protection requirements. They can also be the consequence of accidents that have released radioactive material to the environment. Radioactive residues are also generated by nature, e.g. in natural deposits of radioactive material found in the earth. Spring waters convey these materials. No matter what the cause of radioactive residues may be, there is the question of whether any restoration of the affected environment is required and, if so, to what extent it should be performed. The International Symposium on Restoration of Environments with Radioactive Residues was devoted to discussing these questions and to fostering the exchange of information on this subject. The Symposium explored five main topics: global overview of the problem; restoration principles and criteria; case studies of actual radiological assessments; a critical analysis of the case studies; and the role of public participation in the decision aiding and decision making processes. The Programme Committee of the Symposium accepted a number of contributed papers and posters for consideration at the Symposium, and these were published shortly before the Symposium. In early 2000, the IAEA released as Working Material a draft, unedited compilation of the present Proceedings Series publication. The present publication, which constitutes the record of

  16. Radioactive contamination in the environs of the Hanford Works for the period April - May - June, 1948

    Energy Technology Data Exchange (ETDEWEB)

    Singlevich, W.

    1948-10-15

    This report summarizes the radioactive contamination measured at the Hanford Works and immediate plant areas for the quarter April, May, and June, 1948. Topics discussed are: Meteorology; airborne contamination; contamination in the Columbia and Yakima Rivers; and contamination in rain, drinking water, vegetation, and in Hanford Wastes.

  17. Assessment of the potential radiological impact of residual contamination in the Maralinga and Emu areas

    International Nuclear Information System (INIS)

    Haywood, S.M.; Smith, J.

    1990-10-01

    The report presents an assessment of potential doses to future inhabitants of the Maralinga and Emu areas of Southern Australia, where nuclear weapons tests in the 1950s and 1960s resulted in widespread residual radioactive contamination. Annual effective doses of several millisieverts would be expected to result from continual occupancy within contours enclosing areas of several hundred square kilometres. Larger predicted annual effective doses - of the order of 0.5 Sv -would be expected to occur from 100% occupancy in small regions immediately surrounding the test sites, but continual occupancy of such areas is highly unlikely because of their small size. The most significant dose pathways are inhalation of resuspended activity and ingestion of soil by infants. An analysis of the effects of uncertainties in the dose calculation indicated the uncertainty distribution on predicted doses from the inhalation pathway. (author)

  18. Simplified model for radioactive contaminant transport: the TRANSS code

    International Nuclear Information System (INIS)

    Simmons, C.S.; Kincaid, C.T.; Reisenauer, A.E.

    1986-09-01

    A simplified ground-water transport model called TRANSS was devised to estimate the rate of migration of a decaying radionuclide that is subject to sorption governed by a linear isotherm. Transport is modeled as a contaminant mass transmitted along a collection of streamlines constituting a streamtube, which connects a source release zone with an environmental arrival zone. The probability-weighted contaminant arrival distribution along each streamline is represented by an analytical solution of the one-dimensional advection-dispersion equation with constant velocity and dispersion coefficient. The appropriate effective constant velocity for each streamline is based on the exact travel time required to traverse a streamline with a known length. An assumption used in the model to facilitate the mathematical simplification is that transverse dispersion within a streamtube is negligible. Release of contaminant from a source is described in terms of a fraction-remaining curve provided as input information. However, an option included in the code is the calculation of a fraction-remaining curve based on four specialized release models: (1) constant release rate, (2) solubility-controlled release, (3) adsorption-controlled release, and (4) diffusion-controlled release from beneath an infiltration barrier. To apply the code, a user supplies only a certain minimal number of parameters: a probability-weighted list of travel times for streamlines, a local-scale dispersion coefficient, a sorption distribution coefficient, total initial radionuclide inventory, radioactive half-life, a release model choice, and size dimensions of the source. The code is intended to provide scoping estimates of contaminant transport and does not predict the evolution of a concentration distribution in a ground-water flow field. Moreover, the required travel times along streamlines must be obtained from a prior ground-water flow simulation

  19. Symposium: Treatment of radioactive residues at Hauptabteilung Dekontaminationsbetriebe (HDB)

    International Nuclear Information System (INIS)

    Pfeifer, W.

    1994-05-01

    The twelve seminar papers compiled in the KfK report deal with the current state of the art and the technology available in Germany for the management of radioactive liquid and solid wastes, and radioactive scrap. Some papers discuss particular technical aspects of techniques such as solidification, volume reduction, and compaction. The function of the Waste Collecting Centres of the Laender is explained. (HP) [de

  20. Radioactive contamination of former Semipalatinsk test site area

    International Nuclear Information System (INIS)

    Artem'ev, O.I.; Akhmetov, M.A.; Ptitskaya, L.D.

    2001-01-01

    The nuclear weapon infrastructure elimination activities and related surveys of radioactive contamination are virtually accomplished at the Semipalatinsk test site (STS). The radioecological surveys accompanied closure of tunnels which were used for underground nuclear testing at Degelen technical field and elimination of intercontinental ballistic missile silo launchers at Balapan technical field. At the same time a ground-based route survey was carried out at the Experimental Field where aboveground tests were conducted and a ground-based area survey was performed in the south of the test site where there are permanent and temporary inhabited settlements. People dwelling these settlements are mainly farmers. The paper presents basic results of radiological work conducted in the course of elimination activities. (author)

  1. Onsite disposal of radioactive waste: Estimating potential groundwater contamination

    International Nuclear Information System (INIS)

    Goode, D.J.; Neuder, S.M.; Pennifill, R.A.; Ginn, T.

    1986-11-01

    Volumes 1 and 2 of this report describe the NRC's methodology for assessing the potential public health and environmental impacts associated with onsite disposal of very low activity radioactive materials. This volume (Vol. 3) describes a general methodology for predicting potential groundwater contamination from onsite disposal. The methodology includes formulating a conceptual model, representing the conceptual model mathematically, estimating conservative parameters, and predicting receptor concentrations. Processes which must generally be considered in the methodology include infiltration, leaching of radionuclides from the waste, transport to the saturated zone, transport within the saturated zone, and withdrawal at a receptor location. A case study of shallow burial of iodine-125 illustrates application of the MOCMOD84 version of the US Geological Survey's 2-D solute transport model and a corresponding analytical solution. The appendices include a description and listing of MOCMOD84, descriptions of several analytical solution techniques, and a procedure for estimating conservative groundwater velocity values

  2. Method of burning ion-exchange resin contaminated with radioactivity

    International Nuclear Information System (INIS)

    Suzuki, Shigenori.

    1986-01-01

    Purpose: To process spent ion exchange resins to reduce their volume, without increasing the load on a off-gas system and in a stable state and at the same time not leaving any uncombusted portions. Method: The water slurries of the ion exchange resins contaminated with radioactive materials is dehydrated or dry combusted to reduce the water content. A binder is then added to solidify the ion exchange resin. The solidified ion exchange resins are then combusted in a furnace. This prevents the ion exchange resin from being dispersed by air and combustion gases. Furthermore, the solidified ion exchange resins in the form of small pellets burn from the surface inwards. Moreover the binder is carbonized by the combustion heat and promotes combustion to convert the ion exchange resins into a solid mass, making sure that no uncombusted portion is left. (Takahashi, M.)

  3. Epidemiologic studies of radioactively contaminated environments and cancer clusters

    International Nuclear Information System (INIS)

    Boice, J.D. Jr.

    1991-01-01

    This paper reports on epidemiologic studies which address the distribution and determinants of disease in human populations. Investigations of the possible adverse effects of living in radioactively contaminated environments are difficult to conduct, however, because human populations tend to be fairly mobile, cumulative exposures to individuals from environmental conditions are difficult to estimate, and the risks associated with such exposures tend to be small relative to background levels of disease. Such studies can be arbitrarily classified as geographic correlation surveys, analytic studies, and cluster evaluations. Geographic correlation studies (ecological surveys) relate disease in populations to area characteristics. Although exposure to individuals is unknown, these exploratory or hypothesis-generating studies can identify areas to target for further in-depth evaluation. Analytic investigations relate individual exposure information to disease occurrence. Unusual occurrences of disease in time and place (clusters) occasionally point to a common environmental factor; cluster evaluations have been most successful in identifying the source of infectious disease outbreaks

  4. Disposal of slightly contaminated radioactive wastes from nuclear power plants

    Energy Technology Data Exchange (ETDEWEB)

    Minns, J.L. [Nuclear Regulatory Commission, Washington, DC (United States)

    1995-02-01

    With regard to the disposal of solid wastes, nuclear power plants basically have two options, disposal in a Part 61 licensed low-level waste site, or receive approval pursuant to 20.2002 for disposal in a manner not otherwise authorized by the NRC. Since 1981, the staff has reviewed and approved 30 requests for disposal of slightly contaminated radioactive materials pursuant to Section 20.2002 (formerly 20.302) for nuclear power plants located in non-Agreement States. NRC Agreement States have been delegated the authority for reviewing and approving such disposals (whether onsite or offsite) for nuclear power plants within their borders. This paper describes the characteristics of the waste disposed of, the review process, and the staff`s guidelines.

  5. Conditioning of radioactive ash residue in a wave of solid-phase exothermal reactions

    International Nuclear Information System (INIS)

    Karlina, O.K.; Varlakova, G.A.; Ozhovan, M.I.; Tivanskij, V.M.; Dmitriev, S.A.

    2001-01-01

    The abilities for utilization of exothermic reaction heat in solid phase for conditioning the ash residue produced as a result of solid radioactive waste burning are analyzed. It is shown that the process of ash residue making monolithic with obtaining the glass-like finish product containing 50-60 mass % of ash residue which meets the requirements for solidified radioactive wastes may be realized without energy supplying from external heat sources. The conditioning is realized in a special crucible furnace-container designed not only for the process conducting but also for subsequent storage or disposal of the finish product [ru

  6. Honey As A Bioindicator Of Environmental Radioactive Contamination In Croatia

    International Nuclear Information System (INIS)

    Franic, Z.; Petrinec, B.; Marovic, G.

    2015-01-01

    Radioecological investigations regarding fission products in foodstuffs in Croatia are implemented as part of an extended and still ongoing radioactive contamination monitoring programme of the human environment. The programme has been designed and endorsed by the Croatian State Office for Radiological and Nuclear Security and fully harmonized with European legislation, i.e. the European Commission's recommendation of June 2000 on the application of Article 36 of the Euratom Treaty. For describing the overall possible impact the contaminants have on the entire region, the most efficient sampler would be one that covers the largest area possible. In this sense, honey has been shown to be an excellent biological indicator for detecting radionuclides but also other pollutants such as heavy metals. In Croatia, radiocaesium nuclides like 137Cs and 134Cs in honey were first investigated after the Chernobyl accident in 1986. For both radionuclides, the activity concentrations in honey, which peaked in May 1986, decreased exponentially and the estimated ecological residence time, corrected for radioactive decay, was found to be 1.23 y for 137Cs and 1.07 y for 134Cs. In the early 1990s, activity concentrations in honey for both radionuclides were under the detection limit, but again rose after the Fukushima Daiichi accident. Effective radiation doses due to radiocaesium, received by the Croatian population by honey consumption, even in the year of the Chernobyl accident were estimated to be very small, the per caput dose being less than 1 micro Sv. Based on radioecological investigations of honey, we argue that the mobility of honey bees and their ability to integrate all exposure pathways could add another level of confidence to the present monitoring program if honey and other bee-farming products are included in the routine radioecological monitoring programme for the Croatian environment. (author).

  7. Radioactive contamination of copper produced using nuclear explosives

    Energy Technology Data Exchange (ETDEWEB)

    Crouse, D J; Arnold, W D; Hurst, F J

    1970-05-15

    Laboratory tests simulating the processing of copper ore after fracturing with nuclear explosives indicate that only very small fractions of the radioactive fission products will be dissolved on leaching with dilute sulfuric acid. Tritium (as tritiated water) will be by far the dominant radionuclide in the circulating leach liquor, assuming use of a fusion device. Only 106Ru appears of significant importance with respect to contamination of the cement copper. It is rejected effectively in electrolytic purification and, therefore, the final copper product should be very low in radiocontamination and not hazardous to the customer. The activity level may be high enough, however, to make the copper unsuitable for some specific uses. If necessary, solvent extraction can be used as an alternative to the cementation process to reduce the radioactivity of the copper products. The tritium in the circulating liquor and the 106Ru in the cement copper are potential hazards at the plant site and must be given consideration in designing and operating the facility. However since the activity levels will be low, the protection necessary to ensure safety of the operating personnel should be neither difficult nor costly to provide. (author)

  8. Radioactive contamination characteristics in China following Chernobyl accident

    International Nuclear Information System (INIS)

    Wang Zuoyuan

    1987-01-01

    In the aftermath of Chernobyl nuclear reactor accident, the Environmental Radiation Surveillance Network of Ministry of Public Health of China has done monitoring on environmental samples to determine the contamination levels of radioactivity. Radionuclides, such as I-131, I-132, Cs-137, Cs-134 and Te-132, were found on surface of airplanes, which flew in domestic airlines between May 1-3, that means the radionuclides from Chernobyl accident already reached high altitude atmosphere over China, but the concentration was much lower than that in Europe. During the period of May 2-15, in most stations, radionuclides were found in different environmental samples, such as air, milk, vegetables, rain water, river and lake water, and sheep thyroid. Radioactivity levels of samples were higher in north part of China than in south. The amounts of radionuclides in all samples were well below the derived air concentrations and derived intake concentrations specified in the National Basic Health Standards for Radiological Protection. Thus, the public need not to take any precautions for the purpose of radiation protection

  9. On-site radioactive soil contamination at the Andreeva Bay shore technical base, Northwest Russia

    NARCIS (Netherlands)

    Reistad, O.; Dowdall, M.; Selnaes, O. G.; Standring, W. J. F.; Hustveit, S.; Steenhuisen, F.; Sorlie, A.

    The radioactive waste (RAW) storage site at Andreeva Bay in the Russian Northwest has experienced radioactive contamination both as a result of activities carried out at the site and due to incidents that have occurred there in the past such as accidental releases of radioactive materials. The site

  10. NERIS workshop. Lasting contaminations and land development. After Fukushima: the possibility of a lasting radioactive contamination

    International Nuclear Information System (INIS)

    2011-11-01

    The document contains the contributions proposed during a workshop and the content of discussions after these contributions. For the first day, case studies are thus reported and commented: land contamination in Japan after the Fukushima accident, the CENTRACO plant accident, medium and long term stakes within the context of a lasting contamination by pesticides (the case of chlordecone pollution in the French West Indies), the complex and multiple actor challenges in the case of long duration radiological contamination for land agriculture, a lasting contamination in urban environment (the case of Metaleurop). The second session addressed the conditions and means for preparedness of local actors to a lasting radioactive contamination: the Norwegian approach, how to take the post-accidental perspective into account in the local safeguard plans, the PRIME project (research project on radio-ecological sensitivity indices and multi-criteria methods applied to the environment of an industrial territory), the pilot radiation protection project of the Montbeliard district, the OPAL project (to provide the local information commissions with post-accidental zoning information on the different French nuclear sites)

  11. Demolition and removal of radioactively contaminated concrete soil: Aerosol control and monitoring

    Energy Technology Data Exchange (ETDEWEB)

    Newton, G.J.; Hoover, M.D.; Grace, A.C. III

    1995-12-01

    From 1963 to 1985, two concrete-lined ponds were used to reduce the volume of radioactive liquids from the Institute`s research programs. Following withdrawal of the {open_quotes}hot ponds{close_quotes} from active use, the residual sludges and plastic liners of the ponds were removed and shipped to a radioactive waste disposal site. From 1987 to 1994, the concrete structures remained undisturbed pending environmental restoration on the site. Restoration began in 1994 and was completed in 1995. Restoration involved mechanical breakup and removal of the concrete structures and removal of areas of contaminated soils from the site. This report describes the design and results of the aerosol control and monitoring program that was conducted to ensure protection of workers and the environment during the restoration process. The aerosol control and monitoring strategy developed for remediation of the ITRI hot ponds was successful both in preventing dispersion of radioactive dusts and in demonstrating that exposures of workers and offsite releases were within statutory limits.

  12. Experiences in monitoring airborne radioactive contamination in JAERI

    International Nuclear Information System (INIS)

    Ikezawa, Y.; Okamoto, T.; Yabe, A.

    1980-01-01

    The following results were obtained at the Japan Atomic Energy Research Institute (JAERI) from experience in air monitoring at the hot cells for handling highly radioactive materials, the glove box containing plutonium and the cell for producing 99 Mo. (1) The ratios of activities of airborne dust to those of whole dust were of the order of 10 -2 for the semi-volatile form of 125 Sb, and 10 -3 to 10 -4 for the particulate form of 137 Cs, 144 Ce and 144 Pr, when irradiated fuels were cut in the hot cells. (2) The activity median aerodynamic diameter (AMAD) of airborne particle size distributions varied from O.4 to 15 μm with changing geometric standard deviation (sigmasub(g)) 1.7 to 7, depending on types of metallurgical treatment of fuels and on kinds of work in the cells. (3) A resuspension factor (the ratio of the concentration of airborne contamination to the surface contamination) was found to be 4x10 -8 to approximately 2x10 -7 cm -1 for plutonium oxide deposited on the floor surface. (4) The collection efficiency of the charcoal-loaded filter paper for airborne radioiodine, consisting of 60% inorganic and 40% organic iodide, was over 95% under conditions of relative humidity 40 to approximately 80% and face velocity 50 cm/sec, during the production of 99 Mo. (H.K.)

  13. Sanitation of conditioned radioactive waste after a contamination accident

    International Nuclear Information System (INIS)

    Aeppli, J.

    1980-01-01

    In June 1978, there occurred in the port of Ijmuiden, Netherlands, a contamination incident involving drums originating from Switzerkand and containing radioactive wastes intended to be dumped into the sea. The batch of 207 drums excluded from the sea-dumping action had to be sanitated for the next year dumping in such a manner, that these wastes met the international requirements and could be disposed of by sinking them into the Atlantic. As a consequence of extensive sanitation work, requiring part of the wastes to be newly conditioned and several drums to be packaged again, the total weight of the wastes ready for dumping was doubled. The total radiation exposure for the personnel that took part in the individual phases of sanitation amounted to about 10 man-rem. The main causes for this contamination incident were unusual chemical composition of the concentrate to be solidified, unsufficient quality control and a position not suitabble for transport. The measures taken after this incident intend to avoid similar occurrences in the future. (orig.) [de

  14. Radioactivity of combustion residues from coal-fired power stations

    International Nuclear Information System (INIS)

    Vom Berg, W.; Puch, K.H.

    1996-01-01

    Each year in Germany, about 18 mill. t of combustion residues are produced from the combustion of bituminous coal and lignite. They are utilized to a great extent in the construction industry and in mining. During the combustion of coal, the radio-nuclides remain predominantly in the ash. The radionuclide concentration in lignite ash is within the range of that in natural soil. The combustion residues of bituminous coal contain radio-nuclides of a similar order of magnitude as also can occur in natural rock. The utilization of combustion residues in construction materials makes a negligible contribution to radiation exposure through retention in buildings. (orig.) [de

  15. Dose estimation from residual and fallout radioactivity, 1

    International Nuclear Information System (INIS)

    Takeshita, Kenji

    1975-01-01

    External dose rates and cumulative doses for early entrants from areal surveys and simulated experiments are reviewed. The average cumulative doses to infinity at the hypocenters were 101 rad in Hiroshima and 32 rad in Nagasaki, with a variation of about 60 percent. Radioactive fallout areas nearly matched the ''black rain'' areas in Nagasaki and in Hiroshima. Radioactivity in the fallout areas was affected by radioactive decay and by the leaching and dissipation by rains. Considering these factors, the cumulative dose to infinity in the fallout area of Hiroshima was estimated to be 13 rad, excluding internal radiation doses from inhaled and ingested radionuclides. Attempts to estimate radiation dose from internally deposited radionuclides are also described. (auth.)

  16. Costs related to radioactive residues from nuclear power

    International Nuclear Information System (INIS)

    1988-06-01

    The nuclear power enterprises are responsible for proper actions for safe handling and final storage of spent nuclear fuel and radioactive waste from Swedish nuclear power facilities. The most important actions are to plan, build and operate necessary plants and systems. The nuclear power enterprises have designated Swedish Nuclear Fuel and Waste Management Co., (SKB), to perform these tasks. In this report calculations concerning costs to carry out these tasks are presented. The calculations are based upon a plan prepared by SKB. The plan is described in the report. As final storage of the long lived and highly radioactive waste is planned to take place in the 21st century continuing research and development may indicate new methods which may affect system design as well as costs in a simplifying way. Plants and systems already operational are: Transport systems for radioactive waste products; A central temporary storage for spent nuclear fuel, 'CLAB'; A final storage for radioactive waste from operating nuclear facilities, 'SFR 1'. (L.F.)

  17. Current Measures on Radioactive Contamination in Japan: A Policy Situation Analysis.

    Science.gov (United States)

    Gilmour, Stuart; Miyagawa, Shoji; Kasuga, Fumiko; Shibuya, Kenji

    2016-01-01

    radioactive contamination. Monitoring of radioactive materials in food products in the prefectures has been mainly conducted before shipment to restrict the distribution of radio-contaminated foods. Between March 2011 and March 2012, 133,832 tests of non-commercial and commercial products were conducted, and 1,204 tests (0.9%) were found to violate the provisional standards. Since April 2012, 278,275 tests were conducted, and 2,372 tests (0.9%) were found to violate the revised standards. MHLW assessment of representative market baskets of foodstuffs at 15 locations throughout Japan between February and March 2014 found very low estimated dietary intake of radioactive cesium (0.0007-0.019 mSv/year), as did assessments of the contents of an average day's food. Monitoring of fisheries products in coastal areas affected by the nuclear accident found very limited and declining radio-contamination of live fish outside of Fukushima prefecture. Fisheries monitoring is of limited geographical scope and covers only certain fishes. Area-specific bans on production and distribution have been effective in preventing radioactive contamination in the Japanese food market. Currently there is no major concern about radioactive cesium concentrations in retail foodstuffs in Japan, and very low levels of contamination at the production and wholesale stage. However, because the residue limits and food safety policies were revised on an ad hoc, emergency basis after the nuclear accident, the monitoring procedure needs to be reviewed based on objective and scientifically rational criteria. A transparent and objective scientific framework is needed for prioritizing foodstuffs for inspection and revising Prefecture-specific restrictions. Monitoring of fishes and other seafood products in the wild should be regularized and the information made more publicly accessible, and monitoring activities expanded to identify foodstuffs that are no longer a food safety risk. Consultation with producers and

  18. Current Measures on Radioactive Contamination in Japan: A Policy Situation Analysis.

    Directory of Open Access Journals (Sweden)

    Stuart Gilmour

    areas at risk of radioactive contamination. Monitoring of radioactive materials in food products in the prefectures has been mainly conducted before shipment to restrict the distribution of radio-contaminated foods. Between March 2011 and March 2012, 133,832 tests of non-commercial and commercial products were conducted, and 1,204 tests (0.9% were found to violate the provisional standards. Since April 2012, 278,275 tests were conducted, and 2,372 tests (0.9% were found to violate the revised standards. MHLW assessment of representative market baskets of foodstuffs at 15 locations throughout Japan between February and March 2014 found very low estimated dietary intake of radioactive cesium (0.0007-0.019 mSv/year, as did assessments of the contents of an average day's food. Monitoring of fisheries products in coastal areas affected by the nuclear accident found very limited and declining radio-contamination of live fish outside of Fukushima prefecture. Fisheries monitoring is of limited geographical scope and covers only certain fishes.Area-specific bans on production and distribution have been effective in preventing radioactive contamination in the Japanese food market. Currently there is no major concern about radioactive cesium concentrations in retail foodstuffs in Japan, and very low levels of contamination at the production and wholesale stage. However, because the residue limits and food safety policies were revised on an ad hoc, emergency basis after the nuclear accident, the monitoring procedure needs to be reviewed based on objective and scientifically rational criteria. A transparent and objective scientific framework is needed for prioritizing foodstuffs for inspection and revising Prefecture-specific restrictions. Monitoring of fishes and other seafood products in the wild should be regularized and the information made more publicly accessible, and monitoring activities expanded to identify foodstuffs that are no longer a food safety risk. Consultation with

  19. Micro-PIXE evaluation of radioactive cesium transfer in contaminated soil samples

    International Nuclear Information System (INIS)

    Fujishiro, F.; Ishii, K.; Matsuyama, S.; Arai, H.; Ishizaki, A.; Osada, N.; Sugai, H.; Kusano, K.; Nozawa, Y.; Yamauchi, S.; Karahashi, M.; Oshikawa, S.; Kikuchi, K.; Koshio, S.; Watanabe, K.; Suzuki, Y.

    2014-01-01

    Highlights: • There are radioactively contaminated soils having a radioactive cesium transfer of 0.01. • Micro-PIXE analysis has revealed an existence of phosphorus in a contaminated soil. • Radioactive cesium captured by phosphorus compound would be due to radioactive transfer. -- Abstract: Micro-PIXE analysis has been performed on two soil samples with high cesium activity concentrations. These soil samples were contaminated by fallout from the accident at Fukushima Daiichi Nuclear Power Plant. One exhibits a radioactive cesium transfer of ∼0.01, and the other shows a radioactive cesium transfer of less than 0.001, even though both samples have high cesium activity concentrations exceeding 10,000 Bq/kg. X-ray spectra and elemental images of the soil samples revealed the presence of chlorine, which can react with cesium to produce an inorganic soluble compound, and phosphorus-containing cesium-capturable organic compounds

  20. Derivation of uranium residual radioactive material guidelines for the former Alba Craft Laboratory site, Oxford, Ohio

    International Nuclear Information System (INIS)

    Nimmagadda, M.; Faillace, E.; Yu, C.

    1994-01-01

    Residual radioactive material guidelines for uranium were derived for the former Alba Craft Laboratory site in Oxford, Ohio. This site has been identified for remedial action under the Formerly Utilized Sites Remedial Action Program (FUSRAP) of the US Department of Energy (DOE). Single nuclide and total uranium guidelines were derived on the basis of the requirement that the 50-year committed effective dose equivalent to a hypothetical individual who lives or works in the immediate vicinity of the former Alba Craft Laboratory site should not exceed a dose of 30 mrem/yr following remedial action for the current use and likely future use scenarios or a dose of 100 mrem/yr for less likely future use scenarios (Yu et al. 1993). The DOE residual radioactive material guideline computer code, RESRAD, which implements the methodology described in the DOE manual for implementing residual radioactive material guidelines, was used in this evaluation

  1. Derivation of uranium residual radioactive material guidelines for the Ventron site

    International Nuclear Information System (INIS)

    Loureiro, C.; Yu, C.; Jones, L.

    1992-03-01

    Residual radioactive material guidelines for uranium were derived for the Ventron site in Beverly, Massachusetts. This site has been identified for remedial action under the Formerly Utilized Sites Remedial Action Program of the US Department of Energy (DOE). The derivations for the single radionuclides and the total uranium guidelines were based on the requirement that the 50-year committed effective dose equivalent to a hypothetical individual who lives or works in the immediate vicinity of the Ventron site should not exceed a dose of 100 mrem/yr following remedial action. The DOE residual radioactive material guideline computer code, RESRAD, which implements the methodology described in the DOE manual for implementing residual radioactive material guidelines, was used in this evaluation

  2. Radioecological conditions in the towns, where the status of radioactive contamination zones will change

    International Nuclear Information System (INIS)

    Ageeva, T.N.; Shapsheeva, T.P.; Zajtsev, A.A.; Makarevich, I.A.

    2015-01-01

    The article presents data of changes in the density of soil contamination in settlements where in 2015 change of the status of contaminated areas is possible. Article contains analysis of monitoring of radioactive contamination of food from private farms, the results of radio ecological inspection conducted in 2013-2014. (authors)

  3. Studies on the radioactive contamination due to nuclear detonations II. Preliminary findings on the radioactive fallout due to nuclear detonations

    Energy Technology Data Exchange (ETDEWEB)

    Nishiwaki, Yasushi [Nuclear Reactor Laboratory, Tokyo Institute of Technology, Tokyo (Japan); Nuclear Reactor Laboratoroy, Kinki University, Fuse City, Osaka Precture (Japan)

    1961-11-25

    Since we have detected a considerable amount of artificial radioactivity in the rain in spring 1954, it has become one of the most important items, from the health physics point of view, to continue measurements of radioactivity in the rain and in the atmosphere. To watch out the radioactive contamination of our environment due to repeated nuclear weapons testings in other countries was also considered to be important from the nuclear engineering point of view, in the sense that the permissible allowances of the radioactivity for the peaceful uses of atomic energy might be lowered if the degree of radioactive contamination due to nuclear testings should continue to increase gradually and indefinitely. If the permissible level were lowered, the cost for radiation protection may be expected to increase at the peaceful uses of atomic energy and should the radioactive contamination increase seriously in the future, it was anticipated that we may have to face a very difficult situation in designing the atomic energy facilities for peaceful purposes in our country. From these points of views, we have been continuing measurements of the radioactivity in the rain in Osaka, Japan since the spring of 1954. Some of the preliminary findings are introduced in this paper.

  4. Studies on the radioactive contamination due to nuclear detonations II. Preliminary findings on the radioactive fallout due to nuclear detonations

    International Nuclear Information System (INIS)

    Nishiwaki, Yasushi

    1961-01-01

    Since we have detected a considerable amount of artificial radioactivity in the rain in spring 1954, it has become one of the most important items, from the health physics point of view, to continue measurements of radioactivity in the rain and in the atmosphere. To watch out the radioactive contamination of our environment due to repeated nuclear weapons testings in other countries was also considered to be important from the nuclear engineering point of view, in the sense that the permissible allowances of the radioactivity for the peaceful uses of atomic energy might be lowered if the degree of radioactive contamination due to nuclear testings should continue to increase gradually and indefinitely. If the permissible level were lowered, the cost for radiation protection may be expected to increase at the peaceful uses of atomic energy and should the radioactive contamination increase seriously in the future, it was anticipated that we may have to face a very difficult situation in designing the atomic energy facilities for peaceful purposes in our country. From these points of views, we have been continuing measurements of the radioactivity in the rain in Osaka, Japan since the spring of 1954. Some of the preliminary findings are introduced in this paper

  5. Derivation of residual radioactive material guidelines for uranium in soil at the Middlesex Sampling Plant Site, Middlesex, New Jersey

    International Nuclear Information System (INIS)

    Dunning, D.E.

    1995-02-01

    Residual radioactive material guidelines for uranium in soil were derived for the Middlesex Sampling Plant (MSP) site in Middlesex, New Jersey. This site has been designated for remedial action under the Formerly Utilized Sites Remedial Action Program (FUSRAP) of the US Department of Energy. The site became contaminated from operations conducted in support of the Manhattan Engineer District (MED) and the Atomic Energy Commission (AEC) between 1943 and 1967. Activities conducted at the site included sampling, storage, and shipment of uranium, thorium, and beryllium ores and residues. Uranium guidelines for single radioisotopes and total uranium were derived on the basis of the requirement that the 50-year committed effective dose equivalent to a hypothetical individual living or working in the immediate vicinity of the MSP site should not exceed a dose of 30 mrem/yr following remedial action for the current-use and likely future-use scenarios or a dose of 100 mrem/yr for less likely future-use scenarios. The RESRAD computer code, which implements the methodology described in the DOE manual for establishing residual radioactive material guidelines, was used in this evaluation. Four scenarios were considered for the site. These scenarios vary regarding future land use at the site, sources of water used, and sources of food consumed

  6. Behavior of radioactive cesium during incineration of radioactively contaminated wastes from decontamination activities in Fukushima.

    Science.gov (United States)

    Fujiwara, Hiroshi; Kuramochi, Hidetoshi; Nomura, Kazutaka; Maeseto, Tomoharu; Osako, Masahiro

    2017-11-01

    Large volumes of decontamination wastes (DW) generated by off-site decontamination activities in Fukushima Prefecture have been incinerated since 2015. The behavior of radioactive cesium during incineration of DW was investigated at a working incineration plant. The incineration discharged bottom ash (BA) and fly ash (FA) with similar levels of radiocesium, and the leachability of the radiocesium from both types of ash was very low (incineration of contaminated municipal solid waste (CMSW) reported in earlier studies. The source of radiocesium in DW-FA is chiefly small particles derived from DW and DW-BA blown into the flue gas, not the deposition of gaseous synthesized radiocesium compounds on the surfaces of ash particles in the flue gas as observed in CMSW incineration. This source difference causes the behavior of radiocesium during waste incineration to differ between DW and CMSW. Copyright © 2017 Elsevier Ltd. All rights reserved.

  7. Radioactive contamination level of vehicles resulted from transporting fine rare-earth minerals by rail

    International Nuclear Information System (INIS)

    Han Kaichun; Yu Boyong; Gao Shengwei

    1997-01-01

    This paper presents monitoring results of radioactive contamination level of steel open wagon surface resulted from transporting fine rare-earth minerals. Under promising transport conditions (the packaging consists of two layers of plastic bags and two layers of plastic net sacks, each package contains 50 kg of minerals, each vehicle carries 60 t), the surface radioactivity (total α and total β) of 16 vehicles on two lines from Baotou to Wujiachuan (924 km) and from Baotou to Sankeshu (2236 km) was measured before loading, after unloading and washing, using α and β surface contamination detector. The results showed that the radioactive contamination level of the vehicle surface after unloading appeared significantly different. The contamination level of vehicle bases was higher than that of both sides, long distance vehicles was higher than that of short distance vehicles. The radioactive contamination level of vehicles surface after washing was below the standard limits, these vehicles can be used for ordinary goods transport

  8. Control of the surface radioactive contamination in the field of biological research

    International Nuclear Information System (INIS)

    Calvo, S.; Encina, A. de la; Gaspar, J.; Macias, M. T.; Sanchez, A.; Usera, F.

    2012-01-01

    The manipulation of unsealed sources in biomedical research involves significant risk of radioactive contamination. the aim of this study has been to analyze the radioactive contamination occurring in the field of biomedical research, assessing its magnitude, identifying the equipment that can be contaminated with higher probability and monitoring the evolution of the contaminations production taking into account the radioisotopes and the activities uses, and the radiation protection control applied. The data used for this study correspond to a very lengthy period of time and it have been collected in the radioactive facility, of the Centro Nacional de Biotecnologia (CSIC), a very large biological research centre that can be used perfectly as a reference for this area. The results obtained show a gradual and significant decrease in the incidence of the radioactive contamination. This is due to the optimization of radiation protection standards applied and the implementation or a systematic operational radiation protection program. (Author) 13 refs.

  9. Plant protection under conditions of radioactive contamination of agricultural lands

    International Nuclear Information System (INIS)

    Filipas, A.S.; Oulianenko, L.N.; Pimenov, E.P.

    1995-01-01

    Increasing influence of anthropogenic contaminants as well as substantiated risk of the action of ionizing radiation on agroecosystems suggest the necessity of studying both the state of separate components of cenosis and search for methods on retention of ecosystem stability as a whole. In this case it should be taken into account that by retention of resistance of living organisms to the action of stress agents not only genetically conditioned potential but induction of protective reactions at the expense of ecogene action is of deciding significance as well. Protection of agricultural plants on the territories subjected to radioactive contamination resulting from the ChNPP accident brings attention of research works to a series of problems, the main one being the minimization of pesticide use by the total ecologization of technological processes, in plant growing. But an ordinary discontinuance of conducting protective chemical measures leads to growth in the number of harmful organisms in crop sowings and as a consequence an increase of crop loss and decrease of its quality. It is possible to solve this problem by introduction of measures increasing the resistance of agricultural plants to the action of unfavorable factors of environment. Application of biologically active substances (BAS) of natural and synthetic nature for incrustation of seeds fits into these methods. For the territories with increased content of radionuclides and especially by their rehabilitation the methods of preventive treatments directed to retarding the development of harmful organisms in crop sowings and excluding subsequent technological operations on chemical protection of sowings takes on special significance as it is directly connected with the problem of radiation burden on workers of agroindustrial complex

  10. Radioactive contamination: what actions for the polluted sites

    International Nuclear Information System (INIS)

    Lacoste, A.C.; Averous, J.; Palut-Laurent, O.; Dupuis, M.C.; Paquot, A.; Barescut, J.C.; Cessac, B.; Darmendrail, D.; Grevoz, A.

    2004-01-01

    A national conference was held on May, 2004, in Paris. It concerned the radioactively polluted soil and sites, in order to identify action strategies for the treatment of radioactive pollution. Several aspects have been studied: action plan for radioactivity polluted sites, regulation of radioactively polluted sites in France, situation and practice abroad, natural radioactivity and radioactive pollution: definition and limits, inventory and descriptive data on polluted sites in France and in Europe, radioactive waste and radioactivity polluted sites management: national inventory contribution, then ended with three panels sessions about experience feedback on the management of radioactively polluted sites, responsibilities, legal and regulatory context and financing issues, from evaluation to remediation for polluted sites. (N.C.)

  11. Removal of residual contaminants in petroleum-contaminated soil by Fenton-like oxidation

    Energy Technology Data Exchange (ETDEWEB)

    Lu Mang [School of Material Science and Engineering, Jingdezhen Ceramic Institute, Jingdezhen, 333001, Jiangxi Province (China); State Key Laboratory of Heavy Oil Processing, China University of Petroleum, Beijing 102249 (China); Zhang Zhongzhi, E-mail: zzzhang1955@hotmail.com [State Key Laboratory of Heavy Oil Processing, China University of Petroleum, Beijing 102249 (China); Qiao Wei; Guan Yueming; Xiao Meng; Peng Chong [State Key Laboratory of Heavy Oil Processing, China University of Petroleum, Beijing 102249 (China)

    2010-07-15

    The degradation of bioremediation residues by hydrogen peroxide in petroleum-contaminated soil was investigated at circumneutral pH using a Fenton-like reagent (ferric ion chelated with EDTA). Batch tests were done on 20 g soil suspended in 60 mL aqueous solution containing hydrogen peroxide and Fe{sup 3+}-EDTA complex under constant stirring. A slurry reactor was used to treat the soil based on the optimal reactant conditions. Contaminants were characterized by Fourier transform infrared spectroscopy and Fourier transform ion cyclotron resonance mass spectrometry. The results showed that the optimal treatment condition was: the molar ratio of hydrogen peroxide to iron = 200:1, and pH 7.0. Under the optimum condition, total dichloromethane-extractable organics were reduced from 14,800 to 2300 mg kg{sup -1} soil when the accumulative H{sub 2}O{sub 2} dosage was 2.45 mol kg{sup -1} soil during the reactor treatment. Abundance of viable cells was lower in incubated Fenton-like treated soil than in untreated soil. Oxidation of contaminants produced remarkable compositional and structural modifications. A fused ring compound, identified as C{sub 34}H{sub 38}N{sub 1}, was found to exhibit the greatest resistance to oxidation.

  12. International symposium on restoration of environments with radioactive residues. Contributed papers

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-07-01

    After the use of radioactive materials or the utilization of nuclear energy, some radioactive residues may remain in the environment and give rise to the exposure of persons living or working in that environment. Most commonly, these residues are the result of human activities that have been carried out in the past without proper regard to the internationally accepted radiation protection requirements for practices, or at that time when those requirements were less stringent than today. Of course unforeseen events such as accidents of concentrations of naturally occurring radioactive material can also lead to higher levels of radioactive residues in theenvironment. The purpose of this Symposium is to foster an information exchange on the restoration of environments with radioactive residues. This includes the principles and criteria for guiding decision making and the methodologies for assessing the radiological situation and developing remediation plans for the human habitats affected. The overall aim is to promote an international consensus on the relevant issues in these areas. This document contains 51 presentations delivered during oral and poster sessions. Each of the presentations was separately indexed and provided with an abstract.

  13. International symposium on restoration of environments with radioactive residues. Contributed papers

    International Nuclear Information System (INIS)

    1999-01-01

    After the use of radioactive materials or the utilization of nuclear energy, some radioactive residues may remain in the environment and give rise to the exposure of persons living or working in that environment. Most commonly, these residues are the result of human activities that have been carried out in the past without proper regard to the internationally accepted radiation protection requirements for practices, or at that time when those requirements were less stringent than today. Of course unforeseen events such as accidents of concentrations of naturally occurring radioactive material can also lead to higher levels of radioactive residues in the environment. The purpose of this Symposium is to foster an information exchange on the restoration of environments with radioactive residues. This includes the principles and criteria for guiding decision making and the methodologies for assessing the radiological situation and developing remediation plans for the human habitats affected. The overall aim is to promote an international consensus on the relevant issues in these areas. This document contains 51 presentations delivered during oral and poster sessions. Each of the presentations was separately indexed and provided with an abstract

  14. Predicting the radioactive contamination of the surroundings near a nuclear power plant

    Energy Technology Data Exchange (ETDEWEB)

    Khristova, M; Paskalev, Z

    1975-01-01

    Predicting the radioactive contamination requires determining the concentration of radioactive material emitted from the stack of a nuclear power plant into the air and deposited on the earth's surface. The main factors determining the degree of contamination are the distance from the stack, the wind velocity and air turbulence. Formulas are presented for predicting the amount of radioactivity as a function of the initial concentration of activity, the distance from the stack and the meteorological condition. Formulas are given for the maximum deposition of radioactive aerosols at a distance R from the stack under wet and dry condtions. 2 refs. (SJR)

  15. A prospect of the administration against problems of environmental contamination caused by radioactive nuclides

    International Nuclear Information System (INIS)

    Osako, Masahiro

    2012-01-01

    At first, focusing on the problem of radioactive contaminated wastes caused by Fukushima Daiichi Nuclear Accident, the Author described an outline of the waste management policy based on the law on special measures against the environmental contamination by radioactive nuclides. Next, the Author discussed a prospect of the environmental administration against the radioactive contamination problem. The most important mission of the environmental administration for the future must be to establish a social basis for the sustainable development, in other words the building-up of a newly social value added, through the measures against this unprecedented disaster. (author)

  16. Levels of surface contamination with radioactive materials at workplaces of nuclear research centre at Rez

    International Nuclear Information System (INIS)

    Hoelgye, Z.; Nemcova, I.; Kasikova, M.; Popper, J.; Chysky, J.

    1983-01-01

    A hygiene supervision unit at workplaces of the nuclear Research Institute in Rez monitored on a long-term basis surface contamination with radioactive substances. Surface contamination was found at workplaces with open sources. Of the 4343 monitored places action levels were only exceeded in 13 cases. The obtained data were used for typifying workplaces with the highest level of surface contamination, to determine in certain instances the mechanism of the escape of radioactive substances from insulating facilities and to determine the rate of the spread of the radioactive substance into adjacent non-active workplaces. (author)

  17. Low-waste technology of prevention, decontamination and localization of radioactive contamination

    International Nuclear Information System (INIS)

    Kizhnerov, L. V.; Konstantinov, Ye. A.; Prokopenko, V. A.; Sorokin, N. M.

    1997-01-01

    The report presents the results of research in developing a low-waste technology of prevention, decontamination and localization of radioactive contamination founded on the of easily removed protective polymeric coating based on water and alcohol latexes and dispersion of polymers with special activating additives. The developed technology provides for the reduction of weakly fixed radioactive contamination of non-painted and painted surfaces to admissible levels (as a rule), it securely prevents and localizes contamination and does not generate secondary liquid radioactive wastes

  18. Radioactive contamination of Bunodosoma caissarum under controlled conditions

    International Nuclear Information System (INIS)

    Santos Gouvea, R. de C. dos; Santos, P.L. dos

    The kinetics of uptake and release of radionuclides 137 Cs, 131 I, 133 Ba, 51 Cr (III and VI), 60 Co and 65 Zn in the 'cnidaria' Bunodosoma caissarum have been studied. This is an exclusively Brazilian species and easily collected on the Rio de Janeiro coastal waters. The kinetic experiments have been made in aquariums of 1000 cm 3 , in laboratory under controlled conditions and accompanied by single channel radiometry. The velocities of concentration were evident to radionuclides 131 I and 133 Ba. The larger concentration factors were registred to 51 Cr (III), 65 Zn and 51 Cr (VI), with middle values of 20,0 , 14,5 and 8,6 respectively. The same radionuclides stood out in the loss experiments, presenting the following biological half-lives : 292,2 h ( 51 Cr-III), 784,0 h ( 51 Cr-VI) and 823,0 h ( 65 Zn). This expressive value for the 65 Zn suggests a probable biological integration of this radionuclide by the species studied. The results allow us to indicate the 'anthozoa' Bunodosoma caissarum as a bioindicator of the radioactive contamination of the marine environment. (Author) [pt

  19. Radiological dose assessment for residual radioactive material in soil at the clean slate sites 1, 2, and 3, Tonopah Test Range

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-06-01

    A radiological dose assessment has been performed for Clean Slate Sites 1, 2, and 3 at the Tonopah Test Range, approximately 390 kilometers (240 miles) northwest of Las Vegas, Nevada. The assessment demonstrated that the calculated dose to hypothetical individuals who may reside or work on the Clean Slate sites, subsequent to remediation, does not exceed the limits established by the US Department of Energy for protection of members of the public and the environment. The sites became contaminated as a result of Project Roller Coaster experiments conducted in 1963 in support of the US Atomic Energy Commission (Shreve, 1964). Remediation of Clean Slate Sites 1, 2, and 3 is being performed to ensure that the 50-year committed effective dose equivalent to a hypothetical individual who lives or works on a Clean Slate site should not exceed 100 millirems per year. The DOE residual radioactive material guideline (RESRAD) computer code was used to assess the dose. RESRAD implements the methodology described in the DOE manual for establishing residual radioactive material guidelines (Yu et al., 1993a). In May and June of 1963, experiments were conducted at Clean Slate Sites 1, 2, and 3 to study the effectiveness of earth-covered structures for reducing the dispersion of nuclear weapons material as a result of nonnuclear explosions. The experiments required the detonation of various simulated weapons using conventional chemical explosives (Shreve, 1964). The residual radioactive contamination in the surface soil consists of weapons grade plutonium, depleted uranium, and their radioactive decay products.

  20. Radiological dose assessment for residual radioactive material in soil at the clean slate sites 1, 2, and 3, Tonopah Test Range

    International Nuclear Information System (INIS)

    1997-06-01

    A radiological dose assessment has been performed for Clean Slate Sites 1, 2, and 3 at the Tonopah Test Range, approximately 390 kilometers (240 miles) northwest of Las Vegas, Nevada. The assessment demonstrated that the calculated dose to hypothetical individuals who may reside or work on the Clean Slate sites, subsequent to remediation, does not exceed the limits established by the US Department of Energy for protection of members of the public and the environment. The sites became contaminated as a result of Project Roller Coaster experiments conducted in 1963 in support of the US Atomic Energy Commission (Shreve, 1964). Remediation of Clean Slate Sites 1, 2, and 3 is being performed to ensure that the 50-year committed effective dose equivalent to a hypothetical individual who lives or works on a Clean Slate site should not exceed 100 millirems per year. The DOE residual radioactive material guideline (RESRAD) computer code was used to assess the dose. RESRAD implements the methodology described in the DOE manual for establishing residual radioactive material guidelines (Yu et al., 1993a). In May and June of 1963, experiments were conducted at Clean Slate Sites 1, 2, and 3 to study the effectiveness of earth-covered structures for reducing the dispersion of nuclear weapons material as a result of nonnuclear explosions. The experiments required the detonation of various simulated weapons using conventional chemical explosives (Shreve, 1964). The residual radioactive contamination in the surface soil consists of weapons grade plutonium, depleted uranium, and their radioactive decay products

  1. Structure and dimensions of radioactive contamination caused by use of nuclear weapons

    International Nuclear Information System (INIS)

    Ilijas, B.

    1996-01-01

    Radioactive contamination is one of unavoidable consequences of nuclear burst. Its structure and dimensions are depended of many factors connected with type of weapon, with meteorological conditions and location of burst and characteristics of area involved. Contamination manifests in two ways - as induced radioactivity in the nearness of the center of explosion and as radioactive fallout. Induced radioactivity originates from interaction of neutrons from primary beam with elements naturally presents in environment, which results in creating radionuclides and area of radioactive contamination. Radioactive fallout consists of material formed or collected in the explosion that falls on earth in form of small particles. This contaminant contains α, β and γ sources with structure dependent of explosive energy and location of burst. Some radionuclides, often present in fallout, are very dangerous as internal sources ( 90 Sr, 131 I, 137 Cs, 239 Pu). Dimension of contaminated area varies widely, but if one has Knowledge of enough parameters, it is possible to predict its shape, as well as dose rate on some distance from zero point. Preciseness of this work is essentially affected by credibility of data involved and by kind of selected model. Using of well-chosen model enables on-time evaluation of risk from radioactive contamination and planning adequate protection. (author)

  2. Influence of radioactive contamination to agricultural products by rainfall during a nuclear accident

    International Nuclear Information System (INIS)

    Hwang, W. T.; Han, M. H.; Choi, Y. H.; Lee, H. S.; Lee, C. W.

    2001-01-01

    For the consideration of the effects on radioactive contamination of agricultural products by rainfall during a nuclear accident, the wet interception coefficients for the plants were derived, and the previous dynamic food chain model was also modified. From the results, radioactive contamination of agricultural products was greatly decreased by rainfall, and it decreased dramatically according to increase of rainfall amount. It means that the predictive contamination in agricultural products using the previous dynamic food chain model, in which dry interception to the plants is only considered, can be overestimated. Influence of rainfall on the contamination of agricultural products was the most sensitive for 131 I, and the least sensitive for 90 Sr

  3. Real and alleged hazard of radioactive contamination of seas caused by activities of Russian nuclear fleets

    International Nuclear Information System (INIS)

    Lavkovsky, S.A.

    1999-01-01

    The current paper addresses the assessment results of the degree of danger caused by radioactive contamination of seas by wastes from activities of nuclear fleets compared to the results obtained in other works, specifically, in the IASAP program

  4. Investigating the contamination of accelerated radioactive beams with an ionization chamber at MINIBALL

    CERN Document Server

    Zidarova, Radostina

    2017-01-01

    My summer student project involved the operation and calibration of an ionization chamber, which was used at MINIBALL for investigating and determining the contamination in post-accelerated radioactive beams used for Coulomb excitation and transfer reaction experiments.

  5. The use of radiochemical analysis for detecting biotracers of food radioactive contamination in Cherkasy Region

    International Nuclear Information System (INIS)

    Matvyijenko, D.G.

    2003-01-01

    Stable biotracers of radioactive contamination according to the findings of analytical control of the foodstuffs was determined. The use of radiochemical analysis for determining the activity of the foodstuffs and water (Sr-90, Cs-137) was evaluated

  6. Evaluation of indigenously developed plastic scintillator sheet detector for surface radioactive contamination monitoring application

    International Nuclear Information System (INIS)

    Sahani, R.M.; Chaudhary, H.S.; Mahala, V.K.; Senwar, K.R.; Meena, J.P.

    2018-01-01

    Radioactive contamination may be caused by release of radioactivity in the environment due to accident at nuclear plant/reactor or spillage of loose radioactive materials in a laboratory. The protection of workers from potentially hazardous radiations emitted by the contaminants is a matter of prime concern. The detection of such radiations requires a monitoring system capable of measuring the level of radioactivity at the contaminated site. Plastic scintillators are widely used for large area radiation monitoring due to the ease of preparation in different shape and sizes. These detectors are sensitive to beta and gamma radiation therefore can be used for monitoring of beta and gamma contamination. In this paper, performance results of indigenously developed plastic scintillator sheet of area 800 cm 2 are reported

  7. Status policy and criteria for the remediation of sites with radioactive residues in China

    International Nuclear Information System (INIS)

    Yamin, Z.

    1999-01-01

    This paper introduces the status policy and criteria for remediation of sites with radioactive residues in China. We deal with the sites in difference patterns according to their circumstances. For the sites related with the decommissioning of the nuclear fuel cycle facilities, the programs for environmental restoration must be reviewed and approved by the State Environmental Protection Administration (SEPA). And the radioactive waste resulting from these facilities should be collected and eventually disposed of at the regional disposal repositories built by the country. For the sites related with use of radionuclides in medicine, research and industry, as well as the small scale extraction and processing of materials containing natural radionuclides, the provincial environmental authority is responsible for approving the restoration projects. These radioactive wastes should finally be sent to the special radioactive waste repositories built by the provincial environmental authorities. So far 21 waste repositories have been built in some provinces. More then 10 sites with radioactive residues have been restored. The standards for general public dose limit and soil residual radionuclides content have been established. (author)

  8. Decrease of radioactive contamination by official wine-making procedures

    International Nuclear Information System (INIS)

    Foerstel, H.; Steffens, W.

    1993-01-01

    A contamination with strontium may be lowered by precipitation as tartaric acid complex, a contamination with cesium or cobalt by precipitation of hexacyanoferrates, both accepted wine-making techniques. Contaminated must was obtained both by addition of nuclides to products from the wine harvest or better by growing wine plants on contaminated soils. (orig.) [de

  9. Dalgety Bay: Managing the risks from historic radioactive contamination

    Energy Technology Data Exchange (ETDEWEB)

    Dale, P. [Scottish Environment Protection Agency (United Kingdom)

    2014-07-01

    Discrete radioactive items have been detected on a public beach at Dalgety Bay, Fife near Edinburgh, Scotland since 1990. Dalgety Bay is a New town built on the site of a former military airfield which serviced and decommissioned planes between 1917 and 1959. In 2011, monitoring of the affected foreshore reported hundreds of radium sources on the beach with activities up to 76 MBq. Immediate actions included closure of part of the beach, additional signs and an intensification of the monitoring and recovery programme. In order to determine the potential source and magnitude of the problem a programme of investigation was commissioned by both SEPA and the UK's Ministry of Defence MoD. The investigation programme revealed that the coastline at parts of the bay was made largely of ash and clinker the result of burning of wastes at the time the air base was operational. The depth of these deposits is variable but at times can be metres thick and extent several metres inland. This made ground contained radium sources which were being exposed on the foreshore as marine action eroded the coastline. Current monitoring and recovery programmes continue to recover over 100 sources each month from the beach which is around 800 m long in entirety. The potential health consequences of encountering such a source ranged according to the potential exposure scenario. For walkers passing through the area the external doses are practically zero, however if people remove material either inadvertently or deliberately doses from skin contact can be significant. For the skin doses initial estimates of doses have indicated that the dose rates were around 1 Gray per hour per MBq (to 1 cm{sup 2} ) to the 70 micron skin thickness recommended by ICRP[1] (ICRP, 89). For ingestion doses can be in excess of 100 mSv. The major variables defining the committed effective dose are the initial activity and the diverse range in solubility which is from zero to 36%. The potential doses to date give

  10. Using proven, cost-effective chemical stabilization to remediate radioactive and heavy metal contaminated sites

    International Nuclear Information System (INIS)

    Jensen, R.; Sogue, A.

    1999-01-01

    Rocky Mountain Remediation Services, L.L.C. (RMRS) has deployed a cost-effective metals stabilization method which can be used to reduce the cost of remediation projects where radioactivity and heavy metals are the contaminants of concern. The Envirobond TM process employs the use of a proprietary chemical process to stabilize metals in many waste forms, and provides an excellent binding system that can easily be compacted to reduce the waste into a shippable brick called Envirobric TM . The advantages of using chemical stabilization are: (1) Low cost, due to the simplicity of the process design and inexpensive reagents. (2) Chemical stabilization is easily deployed in field applications, which limit the amount of shielding and other protective measures. (3) The process does not add volume and bulk to the treated waste; after treatment the materials may be able to remain on-site, or if transportation and disposal is required the cost will be reduced due to lower volumes. (4) No secondary waste. The simplicity of this process creates a safe environment while treating the residues, and the long-term effectiveness of this type of chemical stabilization lowers the risk of future release of hazardous elements associated with the residues. (author)

  11. Optimization of fodder rations for intensive development of cattle-breeding in an radioactive contaminated zone

    International Nuclear Information System (INIS)

    Stolyarov, G.V.

    1999-01-01

    It has been calculated some variants of the optimal structure of milk cow herd's fodder rations in a radioactive contaminated zone in dependence of the contamination density. Rations were balanced in primary nutritive including digestible protein. It has been determined their costs and specific radioactivity of cesium-137. These fodder rations can be recommended to the farms of the Gomel Region suffered from the Chernobyl nuclear power station explosion

  12. Biological cycles of radioactive contaminants; Les cycles biologiques des pollutions radioactives

    Energy Technology Data Exchange (ETDEWEB)

    Michon, M. -G. [Commissariat a l' energie atomique et aux energies alternatives - CEA (France)

    1959-07-01

    Artificial radio-elements (synthesized for scientific or industrial purposes)having been released, may be absorbed by plants or animals, and may eventually involve a catenation of organisms as some feed on the others. All organisms living in a polluted river become more radioactive than the water, which was to be expected, in as much as organisms are hypertonic in respect to sweet water. Conversely, soil brings into play physico-chemical phenomena (absorption) such that plants can get only a small portion of contaminating radio-elements, land animal feeding on such plants are relatively less exposed to contamination, and carnivorous animals feeding on herbivorous are still less exposed. Man, notably is fairly well protected, whereas lower organisms, notably unicellular organisms may suffer (mutations..). Reprint of a paper published in 'Revue de Pathologie Generale et de Physiologie Clinique', n. 707, April 1959, p. 505-514 [French] L'utilisation a des fins pacifiques ou scientifiques conduit au rejet dans le milieu ambiant de radio-elements artificiels. Ces radio-elements seront plus ou moins absorbes par les plantes et les animaux. Cette pollution va gagner tous les etres vivants a travers les chaines alimentaires. Cependant, l'importance relative de ces absorptions varie avec chaque cas particulier. Par exemple, lors du rejet du radio-element dans un fleuve ou un etang, on constate que tous les etres vivants dans ce milieu presentent une radioactivite specifique superieure a celle du milieu. Ceci n'est pas a priori etonnant puisque tous les etres vivant en eaux douces sont hypertoniques vis-a-vis du milieu. Les facteurs de concentration varient avec la nourriture et des exemples precis sont fournis. A l'inverse, lorsqu'il s'agit de la contamination d'un sol, par suite de phenomenes physicochimiques d'absorption, les plantes ne prelevent qu'une faible partie des radio-elements presents. La nourriture etant moins fortement contaminee, les animaux terrestres le

  13. Pesticide residues and microbial contamination of water resources in the MUDA rice agroecosystem

    International Nuclear Information System (INIS)

    Cheah Uan Boh; Lum Keng Yeang

    2002-01-01

    Studies on the water resources of the Muda rice growing areas revealed evidence of pesticide residues in the agroecosystem. While the cyclodiene endosulfan was found as a ubiquitous contaminant, the occurrence of other organochlorine insecticides was sporadic. The presence of 2,4-D, paraquat and molinate residues was also evident but the occurrence of these herbicides was seasonal. Residue levels of molinate were generally higher than those from the other herbicides. The problem of thiobencarb and carbofuran residues was not encountered. Analyses for microbial contamination revealed that the water resources were unfit for drinking; coliform counts were higher during certain periods of the year than others. (Author)

  14. Criteria and measurement techniques applicable to residual radioactivity on a decommissioned reactor site

    International Nuclear Information System (INIS)

    Woollam, P.B.

    1988-12-01

    This document summarises the radiological criteria which might be developed to cover the release of a partly decommissioned nuclear reactor site, then looks at the techniques available by which the site could be monitored to assure compliance with these criteria. In particular, the implications of existing levels of radioactive contamination resulting from airburst nuclear weapons tests and the Chernobyl accident are discussed. (author)

  15. Decontamination of radioactively contaminated surfaces - Testing of decontamination agents for textiles. 1. ed.

    International Nuclear Information System (INIS)

    1992-01-01

    The present International Standard provides an experimental method for determining the efficiency of the agents for removal radionuclides deposited on textile materials. It applies to testing the detergents which might be used in water solution for cleaning textiles contaminated by radioactive elements. It is applicable for testing the efficiency of detergents for eliminating non-radioactive dirt

  16. Quantitative analysis of residual protein contamination of podiatry instruments reprocessed through local and central decontamination units.

    Science.gov (United States)

    Smith, Gordon Wg; Goldie, Frank; Long, Steven; Lappin, David F; Ramage, Gordon; Smith, Andrew J

    2011-01-10

    The cleaning stage of the instrument decontamination process has come under increased scrutiny due to the increasing complexity of surgical instruments and the adverse affects of residual protein contamination on surgical instruments. Instruments used in the podiatry field have a complex surface topography and are exposed to a wide range of biological contamination. Currently, podiatry instruments are reprocessed locally within surgeries while national strategies are favouring a move toward reprocessing in central facilities. The aim of this study was to determine the efficacy of local and central reprocessing on podiatry instruments by measuring residual protein contamination of instruments reprocessed by both methods. The residual protein of 189 instruments reprocessed centrally and 189 instruments reprocessed locally was determined using a fluorescent assay based on the reaction of proteins with o-phthaldialdehyde/sodium 2-mercaptoethanesulfonate. Residual protein was detected on 72% (n = 136) of instruments reprocessed centrally and 90% (n = 170) of instruments reprocessed locally. Significantly less protein (p podiatry instruments when protein contamination is considered, though no significant difference was found in residual protein between local decontamination unit and central decontamination unit processes for Blacks files. Further research is needed to undertake qualitative identification of protein contamination to identify any cross contamination risks and a standard for acceptable residual protein contamination applicable to different instruments and specialities should be considered as a matter of urgency.

  17. Quantitative analysis of residual protein contamination of podiatry instruments reprocessed through local and central decontamination units

    Directory of Open Access Journals (Sweden)

    Ramage Gordon

    2011-01-01

    Full Text Available Abstract Background The cleaning stage of the instrument decontamination process has come under increased scrutiny due to the increasing complexity of surgical instruments and the adverse affects of residual protein contamination on surgical instruments. Instruments used in the podiatry field have a complex surface topography and are exposed to a wide range of biological contamination. Currently, podiatry instruments are reprocessed locally within surgeries while national strategies are favouring a move toward reprocessing in central facilities. The aim of this study was to determine the efficacy of local and central reprocessing on podiatry instruments by measuring residual protein contamination of instruments reprocessed by both methods. Methods The residual protein of 189 instruments reprocessed centrally and 189 instruments reprocessed locally was determined using a fluorescent assay based on the reaction of proteins with o-phthaldialdehyde/sodium 2-mercaptoethanesulfonate. Results Residual protein was detected on 72% (n = 136 of instruments reprocessed centrally and 90% (n = 170 of instruments reprocessed locally. Significantly less protein (p Conclusions Overall, the results show the superiority of central reprocessing for complex podiatry instruments when protein contamination is considered, though no significant difference was found in residual protein between local decontamination unit and central decontamination unit processes for Blacks files. Further research is needed to undertake qualitative identification of protein contamination to identify any cross contamination risks and a standard for acceptable residual protein contamination applicable to different instruments and specialities should be considered as a matter of urgency.

  18. Radioactive contamination in the environs of the Hanford Works for the period October, November, December 1949

    Energy Technology Data Exchange (ETDEWEB)

    Paas, H.J.; Singlevich, W.

    1950-03-02

    This report summarizes the measurements made for radioactive contamination in the environs of the Hanford Works. The principal sources of the radioactivity originating as a result of operations at Hanford which affect the environment in this area are the two waste stacks in the separations area and the cooling water from the four pile areas. Measurements are also made on samples taken from the Hanford waste systems which are primarily confined within the project proper. Although monthly summaries of these data are reported in Health Instrument Divisions Environs reports, a somewhat more detailed discussion of these data is covered in the quarterly report. In this manner, a better evaluation of possible trends can be detected as a result of the increased number of measurements made available by combining the data for a three month period. The following areas are discussed: meteorology, radioactive contamination of vegetation, airborne contamination and air radiation levels, radioactive contamination in Hanford wastes, radioactive contamination in the Columbia and Yakima rivers; beta activity in rain and snow, and radioactive contamination in drinking water and test wells.

  19. Regulations and decisions in environmental impact assessment of residues radioactivity content

    International Nuclear Information System (INIS)

    Santos, Adir Janete Godoy dos

    2005-01-01

    Surveillance of natural radionuclides in the environment did not have high priority over many years compared to that of man-made radioactivity. There is, however, an increasing interest in such measurements since enhanced exposure to natural radioactivity is receiving the same legal weight as any other radiation exposure. In this context the surveillance of technologically enhanced naturally occurring materials, called TENORM becomes important. In Brazil, the industries of processing and chemical compounds production were developed based on mining, milling, transformation and manufacture of ores from sedimentary origin, ignea or metamorphic, which must determine the radioactive composition of the generated solid wastes and residues. Many solids residues stored in the environment has been of environmental concern facing the industries and environmentalists in Brazil as it presents a potential threat to the surrounding environment and to individuals occupationally exposed. Radiation protection regulations have not been applied yet to these industries, as the Brazilian regulatory agency (Comissao Nacional de Energia Nuclear - CNEN) has only recently published a regulatory guide concerning mining and milling of naturally occurring radioactive materials, which may generate enhanced concentrations of radionuclides. With respect to external and internal exposure to natural radionuclides from the solid residues storage, the nuclides of 232 Th, 235 U and 238 U decay chains are relevant, due to the exposure of workers as well as of members of the public. Radionuclides released from a source can be present as ions, molecules, complexes, mononuclear or polynuclear species, colloids, pseudocolloids, particles or fragments varying in size (nominal molecular mass), structure, morphology, density, valence and charge properties. One of the main points in environmental impact assessment is to identify whether the chemical availability is under influence of these speciation

  20. Evaluating factors affecting the permeability of emulsions used to stabilize radioactive contamination from a radiological dispersal device.

    Science.gov (United States)

    Fox, Garey A; Medina, Victor F

    2005-05-15

    Present strategies for alleviating radioactive contamination from a radiological dispersal device (RDD) or dirty bomb involve either demolishing and removing radioactive surfaces or abandoning portions of the area near the release point. In both cases, it is imperative to eliminate or reduce migration of the radioisotopes until the cleanup is complete or until the radiation has decayed back to acceptable levels. This research investigated an alternative strategy of using emulsions to stabilize radioactive particulate contamination. Emergency response personnel would coat surfaces with emulsions consisting of asphalt or tall oil pitch to prevent migration of contamination. The site can then be evaluated and cleaned up as needed. In order for this approach to be effective, the treatment must eliminate migration of the radioactive agents in the terror device. Water application is an environmental condition that could promote migration into the external environment. This research investigated the potential for water, and correspondingly contaminant, migration through two emulsions consisting of Topein, a resinous byproduct during paper manufacture. Topein C is an asphaltic-based emulsion and Topein S is a tall oil pitch, nonionic emulsion. Experiments included water adsorption/ mobilization studies, filtration tests, and image analysis of photomicrographs from an environmental scanning electron microscope (ESEM) and a stereomicroscope. Both emulsions were effective at reducing water migration. Conductivity estimates were on the order of 10(-80) cm s(-1) for Topein C and 10(-7) cm s(-1) for Topein S. Water mobility depended on emulsion flocculation and coalescence time. Photomicrographs indicate that Topein S consisted of greater and more interconnected porosity. Dilute foams of isolated spherical gas cells formed when emulsions were applied to basic surfaces. Gas cells rose to the surface and ruptured, leaving void spaces that penetrated throughout the emulsion. These

  1. Precaution against radioactive contamination of steel products in Germany

    International Nuclear Information System (INIS)

    Ewers, E.; Schulz-Klemp, V.; Steffen, R.

    1999-01-01

    Regulations for handling of radioactive materials in Germany. Engagement of the Germany Iron and Steel Institute (VDEh) since the end of the eighties and measures taken. Level of radioactivity in uncontaminated steel products. Agreements between steel industry and scrap supplying industry as well as terms of delivery. Actual status of equipment for detection of radioactivity in the German steel plants. Demands of steel users for clean steel. (author)

  2. Assessment of alternatives for long-term management of uranium ore residues and contaminated soils located at DOE's Niagara Falls Storage Site

    International Nuclear Information System (INIS)

    Merry-Libby, P.

    1985-01-01

    About 11,000 m 3 of uranium ore residues and 180,000 m 3 of slightly contaminated soils (wastes) are consolidated within a diked containment area at the Niagara Falls Storage Site located about 30 km north of Buffalo, New York. The residues account for less than 6% of the total volume of contaminated materials but almost 99% of the radioactivity. The average radium-226 concentration in the residues is 67,000 pCi/g. The US Department of Energy is considering several alternatives for long-term management of the wastes and residues, including: improvement of the containment at NFSS, modification of the form of the residues, management of the residues separately from the wastes, management of the wastes and residues at another humid site (Oak Ridge, Tennessee) or an arid site (Hanford, Washington), and dispersal of the wastes in the ocean. Potential radiological risks associated with implementation of any of the alternatives are expected to be smaller than the nonradiological risks of occupational and transportation-related injuries and deaths. Dispersal of the slightly contaminated wastes in the ocean is not expected to result in any significant radiological risk to humans. The residues and wastes will remain hazardous for thousands of years. After controls cease, the radioactive materials will eventually be dispersed in the environment. Loss of the earthen covers over the buried materials is predicted to occur from several hundred to more than two million years, depending primarily on the use of the land surface. Groundwater will eventually be contaminated in all alternatives; however, the groundwater pathway is relatively insignificant with respect to radiological risks to the general population. 2 references, 2 figures, 6 tables

  3. Methodological guide: management of industrial sites potentially contaminated by radioactive substances; Guide methodologique: gestion des sites industriels potentiellement contamines par des substances radioactives

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-07-01

    At the request of the Ministries of Health and the Environment, IPSN is preparing and publishing the first version of the methodological guide devoted to managing industrial sites potentially contaminated by radioactive substances. This guide describes a procedure for defining and choosing strategies for rehabilitating such industrial sites. (author)

  4. Effects of processing techniques on the radioactive contamination of food

    International Nuclear Information System (INIS)

    Bovard, P.; Delmas, J.; Grauby, A.

    Following contamination of cultures of rice, grapes and various vegetables by 90 Sr and 137 Cs, the effect of processing and cooking techniques on the contamination of the food-stuff was investigated [fr

  5. The Norwegian Radiation Protection Authority leads international cooperation on radioactive contamination in the Arctic

    International Nuclear Information System (INIS)

    1995-01-01

    In cooperation with Russia, Norway is responsible for the part of Arctic Monitoring and Assessment Programme (AMAP) concerning radioactivity. An assessment of the consequences of radioactive contamination for the environment in northern areas will be an important part of AMAP's report to the Ministers of the Environment in the eight participating countries in 1996. The report will contain an overview of the sources of the contamination and the level of radioactivity in the environment, in addition to an evaluation of the consequences for humans and the environment

  6. Imaging plant leaves to determine changes in radioactive contamination status in Fukushima, Japan.

    Science.gov (United States)

    Nakajima, Hiroo; Fujiwara, Mamoru; Tanihata, Isao; Saito, Tadashi; Matsuda, Norihiro; Todo, Takeshi

    2014-05-01

    The chemical composition of plant leaves often reflects environmental contamination. The authors analyzed images of plant leaves to investigate the regional radioactivity ecology resulting from the 2011 accident at the Fukushima No. 1 nuclear power plant, Japan. The present study is not an evaluation of the macro radiation dose per weight, which has been performed previously, but rather an image analysis of the radioactive dose per leaf, allowing the capture of various gradual changes in radioactive contamination as a function of elapsed time. In addition, the leaf analysis method has potential applications in the decontamination of food plants or other materials.

  7. Naturally Occurring Radioactive Materials in Uranium-Rich Coals and Associated Coal Combustion Residues from China.

    Science.gov (United States)

    Lauer, Nancy; Vengosh, Avner; Dai, Shifeng

    2017-11-21

    Most coals in China have uranium concentrations up to 3 ppm, yet several coal deposits are known to be enriched in uranium. Naturally occurring radioactive materials (NORM) in these U-rich coals and associated coal combustion residues (CCRs) have not been well characterized. Here we measure NORM (Th, U, 228 Ra, 226 Ra, and 210 Pb) in coals from eight U-rich coal deposits in China and the associated CCRs from one of these deposits. We compared NORM in these U-rich coals and associated CCRs to CCRs collected from the Beijing area and natural loess sediments from northeastern China. We found elevated U concentrations (up to 476 ppm) that correspond to low 232 Th/ 238 U and 228 Ra/ 226 Ra activity ratios (≪1) in the coal samples. 226 Ra and 228 Ra activities correlate with 238 U and 232 Th activities, respectively, and 226 Ra activities correlate well with 210 Pb activities across all coal samples. We used measured NORM activities and ash yields in coals to model the activities of CCRs from all U-rich coals analyzed in this study. The activities of measured and modeled CCRs derived from U-rich coals exceed the standards for radiation in building materials, particularly for CCRs originating from coals with U > 10 ppm. Since beneficial use of high-U Chinese CCRs in building materials is not a suitable option, careful consideration needs to be taken to limit potential air and water contamination upon disposal of U- and Ra-rich CCRs.

  8. Characterization of naturally occurring radioactive materials and Cobald-60 contaminated ferrous scraps from steel industries

    International Nuclear Information System (INIS)

    Chao, H.E.; Chiu, H.S.; Hunga, J.Y.; His, H.W.; Chen, Y.B.

    2002-01-01

    Since the occurrence of radioactively contaminated rebar incident in 1992, steel industries in Taiwan were encouraged by Atomic Energy Council (AEC) to install portal monitor to detect the abnormal radiation in shipments of metal scrap feed. From 1994 through 1999, there were 53 discoveries of radioactivity in ferrous scraps by steel companies. These include 15 orphan radioactive sources, 16 cobalt-60 contaminated rebars, 20 Naturally Occurring Radioactive Material (NORM) contaminated scraps, and two unknowns. Most NORM-contaminated scraps were from abroad. The NORM and cobalt-60 contaminated scraps were taken from the steel mills and analyzed in laboratory. The analytical results of scales and sludge sampled from NORM-contaminated scraps combining with the circumstantial evidences indicate that five possible industrial processes may be involved. They are oil production and treatment, heavy mineral sand benefication and rare earth processing, copper mining and processing, recovery of ammonium chloride by lime adsorption in Ammonium-soda process, and tailing of uranium enrichment process. The cobalt-60 activity and trace elements concentrations of contaminated rebars confirm that all of them were produced domestically in the period from Oct. 1982 to Jan. 1983, when the cobalt-60 sources were lost and entered the electric arc furnace to produce the contaminated rebars. (author)

  9. Evaluation of Radioactive Contamination in Hamadan Nuclear Medicine Centers Using Wipe Technique

    Directory of Open Access Journals (Sweden)

    N. Rostampour

    2014-02-01

    .Conclusion: In centers 1 and 2, most of the radioactive contamination occurred under the hood due to labeling of radiopharmaceuticals activity. Also, in center 3, the highest contamination rate belonged to patients’ corridor that could be due to frequent the area. According to this subject, necessary measures in this regard should be considered by the department responsible for health physics.

  10. Radiological impact on the workers, members of the public, and environment from the partial decommissioning of Pakistan Research Reactor-I and its associated radioactive residues.

    Science.gov (United States)

    Ali, A; Orfi, S D; Manzur, H; Aslam, M

    2001-05-01

    The Pakistan Research Reactor-I (PARR-I) is a swimming pool type research reactor originally designed and built for a thermal power of 5 MW using High Enriched Uranium (HEU) fuel. In 1990-1991 the reactor was redesigned, partially decommissioned and recommissioned to operate with Low Enriched Uranium (LEU) fuel at a thermal power of 10 MW. An essential requirement, construction and commissioning of a wet spent fuel storage bay and fabrication of an irradiated fuel transfer cask were completed before actual dismantling of the reactor core. During the partial decommissioning operations, radioactive waste generated included 600 m3 low-level liquid radioactive waste and 14 m3 of solid radioactive waste with an average specific activity of 4.52 Bq ml(-1) and 2.22 kBq g(-1), respectively. External radiation doses of the workers were determined using TLD (NG 6,7) and direct reading dosimeters. The maximum individual external radiation dose received by any worker during this practice was 5 mSv, which was 25% of the annual dose limit of 20 mSv. Detection and measurement of internal contamination was carried out using bioassay techniques. During the whole operation, not a single case of internal contamination was detected. The ambient radiation levels around waste seepage pits are periodically monitored using TLD (G-2 cards) and G. M. radiation survey meters. Underground migration of radioactivity is checked by analyzing seepage water samples taken from boreholes that have been dug at different locations in the vicinity of the radioactive residues. The monitoring around disposal sites containing radioactive residues has been continued during the last 9 y and will be continued in the future. So far, no rise in the environmental gamma radiation dose level and migration of underground radionuclides has been found in the vicinity of these disposal sites. Working personal during the decommissioning of PARR-I have been found to be radiologically safe. Adherence to the ALARA

  11. A Study on the Method to Discriminate Between the Internal and External Radioactive Contamination Using Whole Body Counter

    International Nuclear Information System (INIS)

    Kong, T. Y.; Kim, H. G.; Yang, H. Y.; Kang, D. W.; Lim, S. N.; Kim, H. J.; Jin, H. H.; Lee, S. G.; Park, S. C.

    2006-01-01

    Whole Body Counter (WBC) is used to identify and measure the radioactivity in the body of human beings in a nuclear power plants (NPPs). In domestic NPPs, it is prescribed that all workers should take a whole body counting after radiation works if the possibilities of radioactive contamination exist or the radioactivity is detected by a portal monitoring. It is, however, found that the external skin contamination is occasionally estimated as the internal radioactive contamination. In this case, the worker assumed to be detected is recommended to take showers for the decontamination of skin and take a whole body counting again. Although the detected radioactivity is reduced remarkably after several decontaminations, confirmed as the external skin contamination, it is determined finally as an internal exposure if the radioactivity is still detected in the body of worker. The amount of detected radioactivity can be much higher than that of the expected for this mistaken contamination since the radioisotopes attached to skin come to be close to the detectors of WBC. Finally, this makes the misjudgment of the external skin contamination as well as the excessively conservative estimation of radioactive contamination. In this study, several experiments were carried out to discriminate between the internal and external radioactive contamination using the humanoid phantom and WBC. Preliminary experimental results indicated that the use of front and backside counts could be applied to the discrimination of the external skin contamination and the difference of detected radioactivities between front and backside counts was less than about factor 2 for the internal contamination

  12. Radioactive contamination status of an elementary school in southern Miyagi Prefecture, Japan, four years after decontamination

    International Nuclear Information System (INIS)

    Yamaguchi, Toshiro; Sato, Mitsuyoshi; Nagakubo, Kazuyoshi

    2017-01-01

    We investigated the radioactive contamination status of an elementary school in southern Miyagi Prefecture, Japan, four years after decontamination. The radioactive dose rate was measured in the playground (n = 36), back yard (n = 1), parking lot (n = 3), and gutters (n = 30) with a thallium-activated sodium iodide scintillation detector. In addition, topsoil from the playground and gutters sediment were measured with a high-purity germanium semiconductor detector, and sand from the parking lot and sediment from gutters was imaged following an autoradiography method. The mean radioactive dose rate in the playground was almost 0.08 μSv/h. The dose rate was higher at sites facing the mountains, near the main gate, and by the front entrance of the school building. Meanwhile, the radioactive cesium (Cs) concentration of sediment imaged using autoradiography was > 8,000 Bq/kg. These results indicated that the radioactive dose rates in the decontaminated school were below the threshold for being a health hazard. However, the topsoil in the playground had been re-contaminated with radioactive Cs, which had likely been transported via dirt attached to children's shoes and car tires. In addition, the radioactive sediment in the gutters had likely been contaminated by rainwater, suggesting that radioactive protection is necessary when handling gutter sediment. (author)

  13. Assessment of the environmental radioactive contamination levels by depleted uranium after NATO aggression on FR Yugoslavia

    International Nuclear Information System (INIS)

    Pavlovic, S.; Pavlovic, R.; Markovic, S; Plecas, I.

    2001-01-01

    During NATO aggression on FR Yugoslavia various ammunition have been used, some of them for the first time. Among others, 30 mm bullets with depleted uranium (DU) penetrators have been used. Radioactivity contamination surveys have started during the war due to indications that DU is used in cruise missiles. Besides that, there were a lot of radioactivity analysis of food, drinking water etc. Some of the obtained results are presented in this paper. Depleted uranium ammunition can permanently contaminate environment and so produce effects on population. Relation of the international radiation and environmental protection standards and contamination levels are discussed as well. (author)

  14. Radioactive residues at nuclear sites in the United States of America

    International Nuclear Information System (INIS)

    Fiore, J.; Rampertaap, A.; Greeves, J.; MacKinney, J.; Raguso, M.; Selstrom, J.

    2000-01-01

    The United States of America has a large number of sites where radioactive materials have been mined, processed, produced, or used. Upon completion of activities at these sites, some will be cleaned up completely and released for unrestricted future use. However, at other sites, contamination will remain on the site following cleanup, requiring long term institutional controls. Depending on the purpose or the activity conducted at a specific site, these locations are generally under the jurisdiction of a federal agency: the United States Department of Energy, the United States Nuclear Regulatory Commission, the United States Environmental Protection Agency, or the United States Department of Defense. However, under certain conditions, the Nuclear Regulatory Commission relinquishes regulatory authority to individual states to regulate the commercial uses of radioactive materials (except for nuclear reactors), so some locations with radioactive materials are under the jurisdiction of individual states. Other sites with naturally occurring radioactive contamination may also be controlled by individual states. One or two sites under the jurisdiction of each agency are discussed where radioactive materials either existed in the past or exist today, and the source of contamination, the anticipated end state, and the process by which the responsible agency did or will conduct cleanup and site closure are described. Several issues are reviewed that must be addressed in order to design and implement remediations that will ensure long term protection for the environment and future inhabitants. The role of citizens in environmental cleanups is examined, and how institutional controls may be applied to ensure long term protection of remediations that leave some contaminants in place. (author)

  15. Radiological survey of the radioactive sands and residues at Lowman, Idaho

    International Nuclear Information System (INIS)

    Haywood, F.F.; Burden, J.E.; Ellis, B.S.; Loy, E.T.; Shinpaugh, W.H.

    1980-08-01

    No uranium ore milling was performed at the Lowman site, which is located approximately 0.8 km northeast of the town of Lowman, Idaho. Nevertheless, approximately 80,000 metric tons of radioactive sands and residues from upgrading of heavy minerals by physical processing methods remain on the site grounds. Measurements of external gamma radiation 1 m above the surface showed exposure rates up to 2.4 mR/hr on site, but the exposure rate off site quickly dropped to the background level in all directions. Analysis of surface soil and sediment samples for 226 Ra and 232 Th indicated a limited spread of radioactive material

  16. DOE`s radioactively - contaminated metal recycling: The policy and its implementation

    Energy Technology Data Exchange (ETDEWEB)

    Warren, S.; Rizkalla, E.

    1997-02-01

    In 1994, the Department of Energy`s Office of Environmental Restoration initiated development of a recycling policy to minimize the amount of radioactively-contaminated metal being disposed of as waste. During the following two years, stakeholders (including DOE and contractor personnel, regulators, members of the public, and representatives of labor and industry) were invited to identify key issues of concern, and to provide input on the final policy. As a result of this process, a demonstration policy for recycling radioactively-contaminated carbon steel resulting from decommissioning activities within the Environmental Management program was signed on September 20, 1996. It specifically recognizes that the Office of Environmental Management has a tremendous opportunity to minimize the disposal of metals as waste by the use of disposal containers fabricated from contaminated steel. The policy further recognizes the program`s demand for disposal containers, and it`s role as the major generator of radioactively-contaminated steel.

  17. Cesium distribution and phases in proxy experiments on the incineration of radioactively contaminated waste from the Fukushima area.

    Science.gov (United States)

    Saffarzadeh, Amirhomayoun; Shimaoka, Takayuki; Kakuta, Yoshitada; Kawano, Takashi

    2014-10-01

    After the March 11, 2011 Tohoku earthquake and Fukushima I Nuclear Power Plant accident, incineration was initially adopted as an effective technique for the treatment of post-disaster wastes. Accordingly, considerable amounts of radioactively contaminated residues were immediately generated through incineration. The level of radioactivity associated with radiocesium in the incineration ash residues (bottom ash and fly ash) became significantly high (several thousand to 100,000 Bq/kg) as a result of this treatment. In order to understand the modes of occurrence of radiocesium, bottom ash products were synthesized through combusting of refuse-derived fuel (RDF) with stable Cs salts in a pilot incinerator. Microscopic and microanalytical (SEM-EDX) techniques were applied and the following Cs categories were identified: low and high concentrations in the matrix glass, low-level partitioning into some newly-formed silicate minerals, partitioning into metal-sulfide compounds, and occurring in newly-formed Cs-rich minerals. These categories that are essentially silicate-bound are the most dominant forms in large and medium size bottom ash particles. It is expected that these achievements provide solutions to the immobilization of radiocesium in the incineration ash products contaminated by Fukushima nuclear accident. Copyright © 2014 Elsevier Ltd. All rights reserved.

  18. Food toxicology. Residues and contaminants: Risks and consumer protection; Lebensmitteltoxikologie. Rueckstaende und Kontaminanten: Risiken und Verbraucherschutz

    Energy Technology Data Exchange (ETDEWEB)

    Nau, H. [Tieraerztliche Hochschule Hannover, ZA Lebensmitteltoxikologie (Germany); Steinberg, P. [Potsdam Univ., Inst. fuer Ernaehrungswissenschaft (Germany); Kietzmann, M. (eds.) [Tieraerztliche Hochschule Hannover, Inst. fuer Pharmakologie, Toxikologie/Pharmazie (Germany)

    2003-07-01

    In a detailed introduction, the basic methods of risk assessment for potentially toxic food constituents are presented as well as the analytical methods applied for measuring even very small concentrations of contaminants. The main classes of substances relevant in foods ar represented, i.e. animal drugs, fungicides and herbicides, natural toxins, contaminants, prions from BSE-infested animals and residues of 'new' proteins and 'new' DNA from genetically modified foods. New legislation in Germany and Europe is presented including the National Residue Monitoring Plant which is to enable annual monitoring of residue concentrations in foods derived from animals. (orig.)

  19. Cleanup procedures at the Nevada Test Site and at other radioactively contaminated sites including representative costs of cleanup and treatment of contaminated areas

    International Nuclear Information System (INIS)

    Talmage, S.S.; Chilton, B.D.

    1987-09-01

    This review summarizes available information on cleanup procedures at the Nevada Test Site and at other radioactively contaminated sites. Radionuclide distribution and inventory, size of the contaminated areas, equipment, and cleanup procedures and results are included. Information about the cost of cleanup and treatment for contaminated land is presented. Selected measures that could be useful in estimating the costs of cleaning up radioactively contaminated areas are described. 76 refs., 16 tabs

  20. Hanford Site Tank 241-C-108 Residual Waste Contaminant Release Models and Supporting Data

    Energy Technology Data Exchange (ETDEWEB)

    Cantrell, Kirk J.; Krupka, Kenneth M.; Geiszler, Keith N.; Arey, Bruce W.; Schaef, Herbert T.

    2010-06-18

    This report presents the results of laboratory characterization, testing, and analysis for a composite sample (designated 20578) of residual waste collected from single-shell tank C-108 during the waste retrieval process after modified sluicing. These studies were completed to characterize concentration and form of contaminant of interest in the residual waste; assess the leachability of contaminants from the solids; and develop release models for contaminants of interest. Because modified sluicing did not achieve 99% removal of the waste, it is expected that additional retrieval processing will take place. As a result, the sample analyzed here is not expected to represent final retrieval sample.

  1. Total gamma activity measurements for determining the radioactivity of residual materials from nuclear power stations

    International Nuclear Information System (INIS)

    Auler, I.; Meyer, M.; Stickelmann, J.

    1995-01-01

    Large amounts of residual materials from retrofitting measures and from decommissioning of nuclear power stations shows such a weak level of radioactivity that they could be released after decision measurements. Expenses incurred with complex geometry cannot be taken with common methods. NIS developed a Release Measurement Facility (RMF) based on total gamma activity measurements especially for these kind of residual materials. The RMF has been applied for decision measurements in different nuclear power plants. Altogether about 2,000 Mg of various types of materials have been measured up to now. More than 90 % of these materials could be released 0 without any restriction after decision measurements

  2. Radioactive Cs in the Severely Contaminated Soils Near the Fukushima Daiichi Nuclear Power Plant

    Energy Technology Data Exchange (ETDEWEB)

    Kaneko, Makoto; Iwata, Hajime; Shiotsu, Hiroyuki; Masaki, Shota; Kawamoto, Yuji; Yamasaki, Shinya; Nakamatsu, Yuki; Imoto, Junpei; Furuki, Genki; Ochiai, Asumi [Department of Chemistry, Kyushu University, Fukuoka (Japan); Nanba, Kenji [Department of Environmental Management, Faculty of Symbiotic System Science, Fukushima University, Fukushima (Japan); Ohnuki, Toshihiko [Advanced Science Research Center Japan Atomic Energy Agency, Tokai (Japan); Ewing, Rodney C. [Department of Geological Sciences, Center for International Security and Cooperation, Stanford University, Stanford, CA (United States); Utsunomiya, Satoshi, E-mail: utsunomiya.satoshi.998@m.kyushu-u.ac.jp [Department of Chemistry, Kyushu University, Fukuoka (Japan)

    2015-09-01

    Radioactive Cs isotopes ({sup 137}Cs, t{sub 1/2} = 30.07 years and {sup 134}Cs, t{sub 1/2} = 2.062 years) occur in severely contaminated soils within a few kilometer of the Fukushima Daiichi nuclear power plant at concentrations that range from 4 × 10{sup 5} to 5 × 10{sup 7} Bq/kg. In order to understand the mobility of Cs in these soils, both bulk and submicron-sized particles elutriated from four surface soils have been investigated using a variety of analytical techniques, including powder X-ray diffraction analysis, scanning electron microscopy (SEM), transmission electron microscopy (TEM), and analysis of the amount of radioactivity in sequential chemical extractions. Major minerals in bulk soil samples were quartz, feldspar, and minor clays. The submicron-sized particles elutriated from the same soil consist mainly of mica, vermiculite, and smectite and occasional gibbsite. Autoradiography in conjunction with SEM analysis confirmed the association of radioactive Cs mainly with the submicron-sized particles. Up to ~3 MBq/kg of {sup 137}Cs are associated with the colloidal size fraction (<1 μm), which accounts for ~78% of the total radioactivity. Sequential extraction of the bulk sample revealed that most Cs was retained in the residual fraction, confirming the high binding affinity of Cs to clays, aluminosilicate sheet structures. The chemistry of the fraction containing submicron-sized particles from the same bulk sample showed a similar distribution to that of the bulk sample, again confirming that the Cs is predominantly adsorbed onto submicron-sized sheet aluminosilicates, even in the bulk soil samples. Despite the very small particle size, aggregation of the particles prevents migration in the vertical direction, resulting in the retention of >98% of Cs within top ~5 cm of the soil. These results suggest that the mobility of the aggregates of submicron-sized sheet aluminosilicate in the surface environment is a key factor controlling the current Cs

  3. Measurement of residual radioactivity in cooper exposed to high energy heavy ion beam

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Eunjoo; Nakamura, Takashi [Tohoku Univ., Sendai (Japan). Cyclotron and Radioisotope Center; Uwamino, Yoshitomo; Ito, Sachiko; Fukumura, Akifumi

    1999-03-01

    The residual radioactivities produced by high energy heavy ions have been measured using the heavy ion beams of the Heavy Ion Medical Accelerator (HIMAC) at National Institute of Radiological Sciences. The spatial distribution of residual radioactivities in 3.5 cm, 5.5 cm and 10 cm thick copper targets of 10 cm x 10 cm size bombarded by 290 MeV/u, 400 MeV/u-{sup 12}C ion beams and 400 MeV/u-{sup 20}Ne ion beam, respectively, were obtained by measuring the gamma-ray activities of 0.5 mm thick copper foil inserted in the target with a high purity Ge detector after about 1 hour to 6 hours irradiation. (author)

  4. Evaluation and analysis of the residual radioactivity for the 15UD Pelletron accelerator facility

    International Nuclear Information System (INIS)

    Sonkawade, R. G.

    2007-01-01

    For the assessment of radiological impact of the accelerators, it will be better to have the documented information on activation of metal parts of the accelerator components. It is very much essential to get reliable data on these subjects. During acceleration of light ion, the residual radioactivity in the accelerator facility was found near the Analyzing Magnet, single slit, Beam Profile Monitors (BPM), Faraday Cups (FC), bellows, beginning of switching magnet bellows, at the target and the ladder. Study with HPGE detector gives an insight of the formation of the short or long lived radionuclides. The different targets used in the light ion experiment were also monitored and proper decommissioning and decontamination steps were followed. This paper presents the data of residual radioactivity in the 15UD Pelletron accelerator infrastructure. (author)

  5. Optimization of Thermochemical, Kinetic, and Electrochemical Factors Governing Partitioning of Radionuclides During Melt Decontamination of Radioactively Contaminated Stainless Steel; TOPICAL

    International Nuclear Information System (INIS)

    VAN DEN AVYLE, JAMES A.; MALGAARD, DAVID; MOLECKE, MARTIN; PAL, UDAY B.; WILLIAMSON, RODNEY L.; ZHIDKOV, VASILY V.

    1999-01-01

    The Research Objectives of this project are to characterize and optimize the use of molten slags to melt decontaminate radioactive stainless steel scrap metal. The major focus is on optimizing the electroslag remelting (ESR) process, a widely used industrial process for stainless steels and other alloys, which can produce high quality ingots directly suitable for forging, rolling, and parts fabrication. It is our goal to have a melting process ready for a DOE D and D demonstration at the end of the third year of EMSP sponsorship, and this technology could be applied to effective stainless steel scrap recycle for internal DOE applications. It also has potential international applications. The technical approach has several elements: (1) characterize the thermodynamics and kinetics of slag/metal/contaminate reactions by models and experiments, (2) determine the capacity of slags for radioactive containment, (3) characterize the minimum levels of residual slags and contaminates in processed metal, and (4) create an experimental and model-based database on achievable levels of decontamination to support recycle applications. Much of the experimental work on this project is necessarily focused on reactions of slags with surrogate compounds which behave similar to radioactive transuranic and actinide species. This work is being conducted at three locations. At Boston University, Prof. Uday Pal's group conducts fundamental studies on electrochemical and thermochemical reactions among slags, metal, and surrogate contaminate compounds. The purpose of this work is to develop a detailed understanding of reactions in slags through small laboratory scale experiments and modeling. At Sandia, this fundamental information is applied to the design of electroslag melting experiments with surrogates to produce and characterize metal ingots. In addition, ESR furnace conditions are characterized, and both thermodynamic and ESR process models are utilized to optimize the process. To

  6. ENTRIA 2014. Memorandum on the disposal of high-level radioactive residuals

    International Nuclear Information System (INIS)

    Roehlig, Klaus-Juergen; Walther, Clemens; Bach, Friedrich-Wilhelm

    2014-01-01

    The memorandum on the disposal of high-level radioactive residuals covers the following issues: description of the problem: a ''wicked problem'', risks and NIMBY, the site selection law, international boundary conditions; disposal strategy and types of facilities: safety and reversibility, long-term surface storage, deep storage; risk and safety; procedural justice and the site selection process; social innovations and the requirement of long-term institutions; conclusion - central stress fields.

  7. Release procedures and disposal of radioactive residual substances at the Medical University Hanover (MHH)

    International Nuclear Information System (INIS)

    Scheller, F.; Behrendt, R.; Harke, H.

    2005-01-01

    The disposal of all radioactive residual packages of the MHH is regulated by the German radiation protection ordinance from 26 th July 2001; shown in appendix III, table 1, column 5: unrestricted release of solid materials and liquids. All radioactive waste packages are collected and handled by the central MHH department for radiation protection. They are sorted for type, nuclide and specific radioactivity. A few packages can directly be released as conventional waste after performing incoming measurements showing very low activity concentrations. Longer living radionuclides with specific activities above the release limits have to be delivered to the national waste disposal. For direct measurements of gamma-emitting radionuclides we use two in-situ-measuring units (ISOCS, Canberra) and a special release unit with 9 plastic scintillators in a fixed geometry (FR-9 PVT, MED Medizintechnik). Fluid beta-emitting radionuclides are measured by taking a fraction and using liquid scintillation counting (LSC). Solid beta-emitting radionuclides activity are calculated. (orig.)

  8. Dating of oilfield contamination by Natural Occurring Radioactive Materials (NORM) using isotopic ratios

    International Nuclear Information System (INIS)

    Al-Masri, M. S.; Othman, I.; Aba, A.

    2008-05-01

    In the present work, the possibility of using radium isotope ratios (226, 224, 228) for dating of NORM contaminated sites in the oilfields due to uncontrolled disposal of produced water into the environmental NORM contaminated soil sample were collected from different locations in Syrian Oilfields and radioactivity analysed. In addition, production water samples were collected and analysed to determine the isotopes ratios of the naturally occurring radioactive materials. The results have shown that the 228 Ra/ 226 Ra can be successfully used to date contaminated soil provided that this ratio is determined in production water. Moreover, the 210 Pb/ 226 Ra activity ratios was used for the first time for dating of contaminated soil where all factors affecting the method application have been evaluated. Furthermore, the obtained results for dating using the three methods were compared with the actual contamination dates provided by the oil companies. (Authors)

  9. The IAEA's functions and policies on the restoration of environments with radioactive residues

    International Nuclear Information System (INIS)

    Gonzalez, A.J.

    2000-01-01

    A global regime for the regulation of radiation sources is being established by the international community. A general agreement has already been achieved in the current international radiation protection recommendations, which should be resolutely applied. Protection against radioactive residues delivering relatively low level radiation doses can be regulated within the framework provided by the growing international regime based on these recommendations and composed of international conventions, safety standards and provisions for the application of these standards. It is to be noted, however, that the international safety regime is not more than a provider of a decision aiding mechanism based mainly on a global scientific consensus on radiation protection. Its outcome can only serve as input to a final (usually wider) decision making process, which may take into account societal and other concerns at a national, or even local, level. Many situations involving radioactive residues arise in the human habitant and, therefore, the decision making process should involve the participation of all relevant stakeholders in that habitant, rather than radiation protection specialists alone. The combination of decision aiding regulations based on the international regime being catalyzed under the IAEA and a decision making process that takes account of local circumstances and stakeholders' interests should prevent the current problems in the regulation of radioactive residues and in the restoration of the affected environments

  10. Development of the Discrimination Programs between the Internal and External Radioactive Contamination of Workers Using a Whole Body Counter

    International Nuclear Information System (INIS)

    Kong, T. Y.; Kim, H. G.; Lim, S. N.; Kim, H. J.; Jin, H. H.; Lee, S. G.; Park, S. C.

    2006-01-01

    A whole body counter (WBC) is used to identify and measure the radioactivity in the body of human beings in a nuclear power plant (NPP). In domestic NPPs, several whole body counters are in operation to monitor the internal radioactive contamination of workers. All workers take a whole body counting after radiation works if there is high possibility of radioactive contamination or the radioactivity is detected by portal monitoring. It is, however, found that the external contamination is occasionally estimated as the internal radioactive contamination. In this case, the worker is recommended to take showers for the decontamination of skin and take a whole body counting again. Although the detected radioactivity is reduced remarkably after several decontaminations, confirmed as the external contamination, it is determined finally as an internal contamination if the radioactivity is still detected in the body of worker. The amount of detected radioactivity can be much higher than that of the expected for this mistaken contamination since the radioisotopes attached to skin come to be close to the detectors of WBC. Finally, this makes not only the misjudgment of the external contamination as the internal contamination, but also the excessively conservative estimation of radioactive contamination. In this study, several experiments were carried out to set up the discrimination program between the internal and external radioactive contamination using the humanoid phantom and a whole body counter. After the analysis of experimental results, we found that the use of front and backside counts could be applied to the discrimination of the external contamination and the ratio of detected radioactivities between front and backside counts was more than about factor 2 for the external contamination

  11. Manufacturing of concrete with residues from iron ore exploitation using the technology of radioactive waste cementation

    Energy Technology Data Exchange (ETDEWEB)

    Versieux, Juniara L.; Lameiras, Fernando S.; Tello, Cledola Cassia Oliveira de, E-mail: juniarani@gmail.com, E-mail: fsl@cdtn.br, E-mail: tellocc@cdtn.br [Centro de Desenvolvimento da Tecnologia Nucelar (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

    2015-07-01

    Radioactive wastes from various segments of economy are immobilized by cementation, because of availability and widespread use in civil construction of cement. New cementitious materials are developed in CDTN using mining residues based on cementing techniques of radioactive wastes. Special procedures were developed to obtain concrete with the use of super plasticizers in which natural sand was totally replaced by mining residues. The motivation for this research is the exploration of banded iron formations (BIF) as iron ore in 'Quadrilatero Ferrifero' of Minas Gerais, where huge amounts of residues are generated with great concern about the environmental sustainability and safety of dams for residue storage. The exploitation of river sand causes many negative impacts, which leads to interest in its replacement by another raw material in mortar and concrete manufacturing. The use of BIF mining residues were studied for manufacturing of concrete pavers to contribute to reducing the impact caused by extraction of natural sand and use of mining residues. Previously developed procedures with total replacement of natural sand for mining residues were modified, including use of gravel to obtain pavers with improved properties. Four different mixtures were tested, in which the proportion of gravel and super plasticizer was varied. Monitored properties of pavers, among others, were compression resistance, water absorption, and void volume. With addition of gravel, the pavers had higher void index than those made only with mortar, and higher resistance to compression after 28 days of curing (an average of 18MPa of those made with mortar to 24MPa of those made with concrete). (author)

  12. Manufacturing of concrete with residues from iron ore exploitation using the technology of radioactive waste cementation

    International Nuclear Information System (INIS)

    Versieux, Juniara L.; Lameiras, Fernando S.; Tello, Cledola Cassia Oliveira de

    2015-01-01

    Radioactive wastes from various segments of economy are immobilized by cementation, because of availability and widespread use in civil construction of cement. New cementitious materials are developed in CDTN using mining residues based on cementing techniques of radioactive wastes. Special procedures were developed to obtain concrete with the use of super plasticizers in which natural sand was totally replaced by mining residues. The motivation for this research is the exploration of banded iron formations (BIF) as iron ore in 'Quadrilatero Ferrifero' of Minas Gerais, where huge amounts of residues are generated with great concern about the environmental sustainability and safety of dams for residue storage. The exploitation of river sand causes many negative impacts, which leads to interest in its replacement by another raw material in mortar and concrete manufacturing. The use of BIF mining residues were studied for manufacturing of concrete pavers to contribute to reducing the impact caused by extraction of natural sand and use of mining residues. Previously developed procedures with total replacement of natural sand for mining residues were modified, including use of gravel to obtain pavers with improved properties. Four different mixtures were tested, in which the proportion of gravel and super plasticizer was varied. Monitored properties of pavers, among others, were compression resistance, water absorption, and void volume. With addition of gravel, the pavers had higher void index than those made only with mortar, and higher resistance to compression after 28 days of curing (an average of 18MPa of those made with mortar to 24MPa of those made with concrete). (author)

  13. Activated carbon immobilizes residual polychlorinated biphenyls in weathered contaminated soil.

    Science.gov (United States)

    Langlois, Valérie S; Rutter, Allison; Zeeb, Barbara A

    2011-01-01

    Activated carbon (AC) has recently been shown to be effective in sequestering persistent organic pollutants (POPs) from aquatic sediments. Most studies have demonstrated significant reductions of POP concentrations in water and in aquatic organisms; however, limited data exist on the possibility of using AC to immobilize remaining POPs at terrestrial contaminated sites. Under greenhouse conditions, pumpkin ssp cv. Howden) were grown, and red wiggler worms () were exposed to an industrial contaminated soil containing a mixture of polychlorinated biphenyls (PCBs), i.e., Aroclors 1254 and 1260) treated with one of four concentrations of AC (0.2, 0.8, 3.1, and 12.5%) for 2 mo. The addition of AC to contaminated soils virtually eliminated the bioavailability of PCBs to the plant and invertebrate species. There were reductions in PCB concentrations of more than 67% in ssp and 95% in . These data suggest that AC could be included as part of comprehensive site closure strategy at PCB-contaminated sites. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

  14. Measures for radiation prevention and remediation of islightly radioactive contaminated sites by phytoremediation and subsequent utilization of the loaded plant residues (PHYTOREST). Final report; Massnahmen zur Strahlenschutzvorsorge radioaktiv belasteter Grossflaechen durch Sanierung mittels Phytoremediation und anschliessende Verwertung der belasteten Pflanzenreststoffe (PHYTOREST). Abschlussbericht

    Energy Technology Data Exchange (ETDEWEB)

    Willscher, Sabine; Werner, Peter [TU Dresden, Pirna (Germany). Inst. fuer Abfallwirtschaft und Altlasten; Jablonski, Lukasz; Wittig, Juliane

    2013-12-30

    contaminated geosubstrates now can be carried out within the radiation protection regulations. Hence, the project provides a substantial contribution to the radiation protection of HM/R contaminated soils. Within the research project, ways for the utilization of HM/R- contaminated plant residuals were highlighted; this gives a substantial contribution for minimization of wastes, the winning of sustainable bioenergy and the recycling of materials. Here, different ways of solutions were investigated. The research project was carried out within the scientific funding program ''Closedown and decommissioning of nuclear facilities''. The results of the project will contribute to the development of a biologically benign, sustainable technique for the remediation of large contaminated areas that originate mostly from the legacy of the former U mining. As a general result of this comprehensive research project, a phytostabilization/ phytoextraction of such SM/R contaminated sites is feasible with a protection of ground water, and the plant crop from phytoremediation of the HM/R contaminated field site can be utilized for the winning of bioenergy (gaseous/ liquid products or thermal utilization). The beneficial combination of phytoremediation and subsequent utilization of the biomass can be further developed to an innovative and sustainable remediation technology with national and international application potential.

  15. Soil treatment to remove uranium and related mixed radioactive contaminants. Final report September 1992--October 1995

    International Nuclear Information System (INIS)

    1996-07-01

    A research and development project to remove uranium and related radioactive contaminants from soil by an ultrasonically-aided chemical leaching process began in 1993. The project objective was to develop and design, on the basis of bench-scale and pilot-scale experimental studies, a cost-effective soil decontamination process to produce a treated soil containing less than 35 pCi/g. The project, to cover a period of about thirty months, was designed to include bench-scale and pilot-scale studies to remove primarily uranium from the Incinerator Area soil, at Fernald, Ohio, as well as strontium-90, cobalt-60 and cesium-137 from a Chalk River soil, at the Chalk River Laboratories, Ontario. The project goal was to develop, design and cost estimate, on the basis of bench-scale and pilot-scale ex-situ soil treatment studies, a process to remove radionuclides form the soils to a residual level of 35 pCi/g of soil or less, and to provide a dischargeable water effluent as a result of soil leaching and a concentrate that can be recovered for reuse or solidified as a waste for disposal. In addition, a supplementary goal was to test the effectiveness of in-situ soil treatment through a field study using the Chalk River soil

  16. Development of an automatic smear sampler and a polymer film for surface radioactive contamination assay

    International Nuclear Information System (INIS)

    Seo, B.-K.; Lee, K.-W.; Woo, Z.-H.; Jeong, K.-S.; Oh, W.-Z.; Han, M.-J.

    2004-01-01

    Measurement of the surface contamination by an indirect method is subject to the various kinds of error according to the sampling person and needs much time and effort in the sampling and assay. In this research, an automatic smear sampler is developed. It improved efficiency for assay work of surface contamination level achieved periodically in a radiation controlled area. Using an automatic smear sampler developed, it is confirmed that radioactive contaminated materials are uniformly transferred to smear paper more than any sampling method by an operator. Also, Solid scintillation proximity membranes were prepared for measuring the amount of radioactive contamination in laboratories contaminated by the low energy beta-ray emitter, such as 3 H and 14 C. Polysulfone scintillation proximity membranes were prepared by impregnating Cerium Activated Yttrium Silicate (CAYS), an inorganic fluor, in a membrane structure. The inorganic fluor-impregnated membranes were applied to detect the radioactive surface contamination. The preparation of membranes was divided into two processes. A supporting polymer film was made of casting solutions consisting of polysulfone and solvent, their cast film being solidified by vacuum evaporation. CAYS-dispersed polymer solutions were cast over the first, solidified polymer films and coagulated either by evaporating solvent in the solution with non-solvent in a coagulation bath. The prepared membranes had two distinguished, but tightly attached, double layers : one is the supporting layer of dense polymer film and the other results revealed that the prepared membranes were efficient to monitor radioactive contamination with reliable counting ability. For enhancement of pick-up and measurement efficiency, the membrane was prepared with the condition of different membrane solidification. The scintillation produced by interaction with radiation and CAYS was measured with photomultiplier tube. The test results showed that the prepared

  17. Complex relationship between groundwater velocity and concentration of radioactive contaminants

    International Nuclear Information System (INIS)

    Kaszeta, F.E.; Bond, F.W.

    1980-01-01

    This paper uses the results from the Multi-component Mass Transport model to examine the complex interrelationship between groundwater velocity and contaminant dispersion, decay, and retardation with regard to their influence on the contaminant concentration distribution as it travels through the geosphere to the biosphere. The rate of transport of contaminants through the geosphere is governed by groundwater velocity, leach rate, and contaminant retardation. The dominant characteristics of the contaminant concentration distribution are inherited during leaching and modified during transport by dilution, dispersion and decay. For a hypothetical non-decaying, non-dispersing contaminant with no retardation properties, the shape of the source term distribution is governed by the groundwater velocity (dilution) and leach rate. This distribution remains unchanged throughout transport. Under actual conditions, however, dispersion, decay and retardation modify the concentration distribution during both leaching and transport. The amount of dispersion is determined by the distance traveled, but it does have a greater peak-reducing influence on spiked distributions than square-shaped distributions. Decay acts as an overall scaling factor on the concentration distribution. Retardation alters the contaminant travel time and therefore indirectly influences the amount of dilution, dispersion and decay. Simple relationships between individual parameters and groundwater velocity as they influence peak concentration do not exist. For those cases where the source term is not solubility-limited and flow past the waste is independent of regional hydrologic conditions, a threshold concentration occurs at a specific groundwater velocity where the effects of dilution balance those of dispersion and decay

  18. Radiological assessment of radioactive contamination on private clothing

    International Nuclear Information System (INIS)

    Schartmann, F.; Thierfeldt, S.

    2003-01-01

    In the very rare, cases where private clothing of persons working in a nuclear installation are inadvertently contaminated and this contamination is not detected when leaving the facility, there may be radiological consequences for this person as well as for members of his or her family. The VGB (Technische Vereinigung der Grosskraftwerksbetreiber) in Germany has investigated in detail the spread of contamination in nuclear power plants. Part of this evaluation programme was a radiological analysis which has been carried out by Brenk Systemplanung GmbH (Aachen/Germany). The radiological analysis started with the definition of the source term. It is highly unlikely that activities of more than 5 kBq 60 Co could leave a plant undetected on the body or the clothes. Nevertheless activities up to 50 kBq and different nuclide vectors were regarded. It has been found that 60 Co is the most important contaminant. The radiological analysis focusses on two types of contamination: particles and surface contamination. The pathways by which such a contamination can lead to an exposure by external irradiation or by ingestion depend on the type of contamination and are analysed in detail. For example, a particle could be retained in pockets or other parts of clothing and may lead to prolonged external irradiation until the piece of clothing is washed. The analysis is performed on the basis of conservative to realistic assumptions. In conclusion, the analysis has shown that especially particle contamination needs to be focussed on. However, by the advanced detection equipment in German plants doses which may pose a health hazard can safely be excluded. (authors)

  19. Roles of concrete technology for containment of radioactive contaminants

    International Nuclear Information System (INIS)

    Kitsutaka, Yoshinori; Imamoto, Keiichi

    2014-01-01

    A large amount of radioactive materials was emitted in the environment by the reactor accident at Fukushima Daiichi Nuclear Power Plant. Nuclear debris still remains in the reactor container. An investigative committee was organized in Japan Concrete Institute to study on the containment of radioactive materials and the safe utilization of concrete materials. We have investigated the effect of the hydrogen explosion upon the property of concrete and the transfer of materials into the concrete. We also present the outline of the advice made by Japan Concrete Institute about technologies on the concrete materials for the waterproofing in buildings and for water-shielding walls. (J.P.N.)

  20. An automatic drawing system for a report radioactive contamination check

    International Nuclear Information System (INIS)

    Saneyoshi, Keiji; Tomita, Satoru; Yoda, Isao

    2002-01-01

    An Automatic drawing system for a report of surface contamination check in a radiation controlled area has been developed. The system can print out the report applied for the format provided by the law from the raw data that is the output from measuring instruments. The task of a worker is only to insert an FD storing the data into a PC and to push a button. The system also yields contamination maps to indicate contamination points clearly. With this system the time to complete the report from the raw data could be decreased from more than two hours to 4 minutes. (author)

  1. A transportable system for radioactivity contaminated water treatment

    International Nuclear Information System (INIS)

    2013-01-01

    Contaminated water treatment system called SARRY for retrieval and recovery of water in operation at the site of Fukushima Daiichi Nuclear Power Plant since August 2011 has been modified by compacting the system size to develop a mobile system SARRY-Aqua that can process Cs-contaminated water (one ton/hour) to the level of 10 Bq/kg. Installing the system in a small container with dimensions conforming to the international standards facilitates transportation by truck and enables the contaminated water treatment occurring in a variety of locations. (S. Ohno)

  2. Method and apparatus for treating liquid contaminated with radioactive particulate solids

    International Nuclear Information System (INIS)

    Hirs, G.

    1976-01-01

    A method and apparatus reduces the amount of radioactive solids resulting from the filtration of particulate contaminants from liquid in a nuclear reactor plant. A filtration system includes a pre-filter comprising a sheet filter medium through which the reactor liquid passes to remove relatively large particulate contaminants for storage or disposal. The reactor liquid is then passed through a bed of granular filter medium to accumulate substantially all the previously non-filtered contaminants and thereby provide a clarified liquid suitable for reuse in the reactor. Backwash liquid is flowed through the granular filter bed to remove and entrain the accumulated contaminants into a slurry which is received by a reservoir where the slurry is maintained quiescently to settle the contaminants. Removal of liquid from the reservoir concentrates the contaminants for storage or further processing, without the necessity of large quantities of filter aids that would increase the quantity of storage-requiring contaminated solids

  3. Modeling the migration of radioactive contaminants in groundwater of in situ leaching uranium mine

    International Nuclear Information System (INIS)

    Li Chunguang; Tai Kaixuan

    2011-01-01

    The radioactive contamination of groundwater from in situ leaching (ISL) of uranium mining is a widespread environmental problem. This paper analyzed the monitor results of groundwater contaminations for a in situ leaching uranium mine. A dynamic model of contaminants transport in groundwater in ISL well field was established. The processes and mechanisms of contaminant transport in groundwater were simulated numerically for a ISL well field. A small quantity of U and SO 4 2- migrate to outside of well field during ISL production stage. But the migration velocity and distance of contaminations is small, and the concentration is low. Contaminants migrate as anomalistic tooth-shape. The migration trend of U and SO 4 2- is consistent. Numerical modeling can provide an effective approach to analyse the transport mechanism, and forecast and control the migration of contaminants in groundwater in ISL well field. (authors)

  4. Early-stage bioassay for monitoring radioactive contamination in living livestock.

    Science.gov (United States)

    Yamaguchi, Toshiro; Sawano, Kaita; Kishimoto, Miori; Furuhama, Kazuhisa; Yamada, Kazutaka

    2012-12-01

    Soil samples from the ground surface and feces and blood from a mixed-breed male pig were collected on April 10, 2011 at a farm within 20 km of the Fukushima Daiichi nuclear power plant. The radioactivity of each sample was measured using a Ge semiconductor detector. Despite the fact that the pig had been fed non-contaminated imported feed, (131)I, (134)Cs and (137)Cs were detected in the feces, and (134)Cs and (137)Cs were detected in the blood clots. Because it is considerably difficult to measure radioactive contamination in the edible muscle of living livestock, bioassays are an option for the screening of radioactive contamination in living livestock to ensure food safety.

  5. Remediation of deltamethrin contaminated cotton fields: residual and adsorption assessment

    Directory of Open Access Journals (Sweden)

    Rafique Uzaira

    2016-01-01

    Full Text Available Pakistan occupies a significant global position in the growing of high quality cotton. The extensive application of pesticides on agricultural products leads to environmental risk due to toxic residues in air, water and soil. This study examined the chemodynamic effect of Deltamethrin on cotton fields. Samples were collected from the cotton fields of D.G. Khan, Pakistan and analyzed for heavy metal speciation patterns. Batch experiments were administered in order to study the adsorption of Deltamethrin in cotton fields. The effect of different factors including pH, adsorbate dose, and adsorbent mass on adsorption were studied. It was observed that in general, adsorption increased with increases in the mass of adsorbate, although the trends were irregular. Residual fractions of deltamethrin in the soil and water of cotton fields were analyzed to assess concentrations of xenobiotics bound to soil particles. Results indicated that such residues are significantly higher in soil samples due to high Koc in comparison to water, indicating the former is an efficient degradation agent. Results from the batch experiment resulted in 95% removal with alkaline pH and an adsorbent-adsorbate ratio of 250:1. These results may be used to environment friendly resource management policies.

  6. Verification of radioactive contamination surveys for practical use in biological research centres

    International Nuclear Information System (INIS)

    Macias, M.T.; Requejo, C.; Ruiz, M.; Pina, R.

    2006-01-01

    Unsealed sources are commonly used in science research laboratories. Their manipulation may imply a radioactive contamination hazard. Therefore, adequate and sensitive survey meters must be available, and must have an effective and accurate response to intensity and type of radiation emitted by the used radionuclides to identify and quantify the possible contamination and then be able to avoid any associated or unwanted consequences that may arise. Periodic surveys are performed to show control, any time, any place radioactive contamination is suspected, and to ensure radioisotopes are being used safely. The immediate work areas must be often checked with portable survey monitors, including the entire lab and particularly bench tops, personnel protective equipment or solely designated equipment for isotope use (micro-fuges, water baths, incubators). These are carried out with portable survey instruments like Geiger-Muller tubes, proportional counters and scintillation detectors that provide direct or indirect measurements capabilities. The Radiation Safety Office (R.S.O.) as well as the radioactive compounds working laboratories at the Instituto de Inv. Biomedicas 'A. Sols' (Madrid-Spain) are provided with an adequate radiation measurement instrument. But, before a portable survey instrument is used, several quality checks should be made (batteries, calibration sticker), and the instrument response should be tested with a check source. This paper aims at determining, with a R.S.O. procedure, these surveys working parameters -detection efficiency, calibration factors and minimum detectable activities-, using reference checking sources ( 14 C, 36 Cl, and 90 Sr/ 90 Y) with known radioactivity covering the energy range of beta emitting isotopes used in biological research. No gamma portable monitors have been tested for the R.S.O. has no gamma checking sources. Therefore, 58 beta monitors were tested, obtaining t he efficiency values, the calibration factors (Bq cm-2 s

  7. Consumer risk perception, attitudes and behaviour related to food affected by radioactive contamination

    International Nuclear Information System (INIS)

    Grande, J.

    1999-01-01

    The paper focuses on consumer attitudes to the countermeasures being taken to reduce radioactivity levels in food. Data is collected from a 1998 survey of 1003 Norwegian and 200 Scottish consumers on their fear of experiencing ill health due to radioactive contamination of food products, their risk averting behaviour connected to the Chernobyl accident of 1986, and their willingness to pay (WTP) for untreated food

  8. The system for measurements of radioactive contamination of environment and food in Poland

    International Nuclear Information System (INIS)

    Grabowski, D.; Kurowski, W.

    1990-01-01

    The service for Measurements of Radioactive Contamination comprises a network of 152 measuring stations. They are carrying out continuous measurements of gamma radiation dose rates and radioactivity measurements of 24 hours samples of air (aerosols) and total fallout. On the territory of each province there are selected points for sampling of environmental materials and food. Frequency of sampling depends on material being collected. 1 tab., 2 figs. (A.S.)

  9. General radioactive contamination of the biosphere in the Netherlands

    International Nuclear Information System (INIS)

    1980-01-01

    The Coordinating Committee for the Monitoring of Radioactive and Xenobiotic Substances (C.C.R.X.) reports the results of the radioactivity measurements in 1979. These are divided into measurements for the National Measuring Programme and Additional Measurements. The former include the analyses considered essential for an efficacious control of the radioactivity of the biosphere and are performed in air, soil, surface water, milk and in deposition on the surface of the earth. Samples of milk and grass from the surroundings of nuclear reactors have also been analysed. Additional measurements comprises orientating research for specific radionuclides which may be present in some samples, and other investigations which may procure useful information. Results of determinations of radionuclides in some fishery-products from the Dutch waters are given in view of the potential which some marine organisms have to concentrate fission products and especially activated corrosion products from nuclear installations. After a discussion of the results for the National Measuring Programme, a calculation is given of the total artificial radioactivity in the average Dutch diet in 1979 and of the total mean annual radiation dose the Dutch population received as a result of the presence of artificial radionuclides. Different methods studied to calculate the bone dose due to Sr-90 in the diet are outlined as an appendix. (Auth.)

  10. Evaluation of dose due to the liberation of the radioactive content present in systems of final disposal of radioactive residues

    International Nuclear Information System (INIS)

    Amado, V.; Lopez, F.

    2006-01-01

    The disposal systems of radioactive residuals well-known as repositories near to the surface, are used to dispose residuals that can contain high concentrations of radionuclides of period of short semi disintegration, which they would decay at levels radiologically insignificant in some few decades or in some centuries: and acceptably low concentrations of radionuclides of period of long semi disintegration. The dose that would receive the critic group due to these systems it could be increased by cause of discreet events that affect the foreseen retard time, or by the gradual degradation of the barriers. To this last case it contributes the presence of water, because it implies leaching and dissolution that can give place to radionuclide concentrations in the underground water greater to the prospective ones. The dosimetric evaluation is important because it offers useful objective information to decide if a given repository is adjusted to the purposes of its design and it fulfills the regulatory requirements. In this work a simplified evaluation of the dose that would receive the critic group due to the liberation of contained radionuclides in a hypothetical system of final disposition of radioactive residuals is presented. For it, they are considered representative values of the usually contained activities in this type of systems and they are carried out some approaches of the source term. The study is developed in two stages. In the first one, by means of the Radionuclide pollutant scattering pattern in phreatic aquifers (DRAF) it is considered the scattering of the pollutants in the phreatic aquifer, until the discharge point in the course of the nearest surface water. This model, developed originally in the regulatory branch of the National Commission of Argentine Atomic Energy (CNEA); it solves the transport equation of solutes in porous means in three dimensions, by the finite differences method having in account the soil retention and the radioactive

  11. An investigation of awareness on the Fukushima nuclear accident and Radioactive contamination

    Energy Technology Data Exchange (ETDEWEB)

    Ha, Jeong Chul; Song, Young Ju [Dept. of Consumer Safety, Korea Consumer Agency, Eumseong (Korea, Republic of)

    2016-05-15

    The objective of this study was to investigate Korean people's awareness about impact of the Fukushima nuclear power plant accident in Japan and radioactive contamination caused by it. The respondents of the survey were 600 adults who resided in the Seoul metropolitan area. The survey results show that the majority of respondents were concerned about impact of radiation leakage that might have an effect on our environment. They were worried about radioactive contamination of foodstuffs, particularly fishery products and preferred to acquire information through TV(49.8%) or the Internet(31.3%). Meanwhile, respondents mentioned that the information on the Fukushima nuclear accident and radioactive contamination had not been sufficient and they didn't know well about the follow-up measures of the government on the accident. Most respondents answered that information on radioactive contamination levels and safety of foods and environment was most needed. The results of this study could be useful to enhance awareness on radioactivity and improve risk communication on nuclear power plant accidents.

  12. Residual radioactivity guidelines for the heavy water components test reactor at the Savannah River Site

    International Nuclear Information System (INIS)

    Owen, M.B. Smith, R.; McNeil, J.

    1997-04-01

    Guidelines were developed for acceptable levels of residual radioactivity in the Heavy Water Components Test Reactor (HWCTR) facility at the conclusion of its decommissioning. Using source terms developed from data generated in a detailed characterization study, the RESRAD and RASRAD-BUILD computer codes were used to calculate derived concentration guideline levels (DCGLs) for the radionuclides that will remain in the facility. The calculated DCGLs, when compared to existing concentrations of radionuclides measured during a 1996 characterization program, indicate that no decontamination of concrete surfaces will be necessary. Also, based on the results of the calculations, activated concrete in the reactor biological shield does not have to be removed, and imbedded radioactive piping in the facility can remain in place. Viewed in another way, the results of the calculations showed that the present inventory of residual radioactivity in the facility (not including that associated with the reactor vessel and steam generators) would produce less than one millirem per year above background to a hypothetical individual on the property. The residual radioactivity is estimated to be approximately 0.04 percent of the total inventory in the facility as of March, 1997. According to the results, the only radionuclides that would produce greater than 0.0.1-millirem per year are Am-241 (0.013 mrem/yr at 300 years), C-14 (0.022 mrem/yr at 1000 years) and U-238 (0.034 mrem/yr at 6000 years). Human exposure would occur only through the groundwater pathways, that is, from water drawn from, a well on the property. The maximum exposure would be approximately one percent of the 4 millirem per year ground water exposure limit established by the U.S. Environmental Protection Agency. 11 refs., 13 figs., 15 tabs

  13. The reality of radioactive contamination in construction of Taiwan and the treatment concerned

    International Nuclear Information System (INIS)

    Huang Chin-Wang

    2005-01-01

    It has been more than 50 years since Taiwan started the research on the peace application of radioactivity. During the first 20-30 years, it was found that the radioactive contaminated waste steel from atomic power plants was recycled together with general waste steel and was used to make other products including reinforcing bars. It was because the radiation resources ware not carefully controlled and managed. Since 1982, the radioactive contaminated reinforcing bars and buildings were gradually found, as the radiation dose rates were 5 μSv/h and 0.5 μSv/h, respectively. The radioactive nuclide was all Co-60. By August 2003, 1,626 households, 7,824 people's houses were founded to be radioactive contaminated. Furthermore, radiation dose rates higher than 5 μSv/h were measured from 264 of those householders. The government has started to ameliorate this situation and 94.7% of the cases have become normal. The cancer death rate of these people is found to be 0.49% (89 patients in 7,824 people, 39 was dead), and it is 4 times higher than that for general people. In order to solute this pollution problem, the government has made the law to check the radioactivity of all reinforcing bars and to control and manage those radiation resources more carefully. Additionally, there are tax exemption, subsidy, and expropriation with compensation for the polluted buildings. (author)

  14. Long term survey on food pollution and contamination by radioactive fallout in Fukuoka, Japan (1961 - 1976)

    International Nuclear Information System (INIS)

    Morishige, Toshiko; Ishinishi, Noburu; Cho, Tetsuji.

    1977-01-01

    The contamination and the pollution of foodstuffs by radioactive fallout have been investigated since 1961 in Fukuoka city and its suburban area. The results obtained were as follows. 1) Recently, the degree of the contamination of greens by radioactive fallout which fell on the leaves decreased to one thousandth in the early stage of the investigation (1961 - 1962). In the period of the investigation, the remarkable increase of the radioactivity of fallout was observed within a week after the Chinese nuclear bomb explosion in the atmosphere (1st, 2nd, 5th, 12th, 13th, and 15th). The radioactivity was 2 to 300 times higher than the usual level. 2) The radioactivity was not remarkable in vegetables which were washed with soap, but it decreased gradually year by year. The increase of the radioactivity was also observed a few days after the atmospheric nuclear explosion. 3) In milk, there were no remarkable yearly decreases of the radioactivity from the beginning of the investigation, but the seasonal variations of the radioactivity, such as higher in April and May, were observed. 4) The radioactivity in diets based on the standard food production in Japan was the highest in 1967. It decreased gradually from 1967 to 1971 and after that the remarkable variation of the activity was not observed. 5) 137 Cs contamination of foodstuffs has been observed quantitatively by the method of gamma spectrometry, while sometimes 95 Zr- 95 Nb, 103 Ru, and 131 I were also detected from the specimens obtained immediately after the nuclear explosions. (auth.)

  15. A United States perspective on long-term management of areas contaminated with radioactive materials

    International Nuclear Information System (INIS)

    Jones, C. R.

    2004-01-01

    The US has far-reaching and extensive experience in the long-term management of areas contaminated with radioactive materials. This experience base includes the Dept. of Energy's continued follow-up with Hiroshima and Nagasaki from the 1940's at the Radiological Effects Research Foundation in Hiroshima (Japan)), the long-term management of the Marshall Islands Programme, the clean-up of the US nuclear weapons complex and the ongoing management of accident sites such as in Palomares (Spain)). This paper discusses the lessons learnt and best practices gained from this far-reaching and extensive experience in the long-term management of areas contaminated with radioactive materials. (authors)

  16. Study on the metabolism of contamination of radioactive materials in organism by autoradiographic techniques

    International Nuclear Information System (INIS)

    Zhu Shoupeng; Zhang Lansheng; Kang Baoan

    1988-08-01

    The metabolism of contamination of radioactive materials in organism was studied by diferent types of autoradiographic techniques, such as: (1) in body level by whole-body autoradiography; (2) in organ level by whole-organ autoradiography; (3) in cellular level by microautoradiography; (4) in subcellular level by electron microscopic autoradiography; (5) in combinative form by tissue fixative autoradiography; (6) in ionizing form by freezing autoradiography; (7) for radioactive mateials with two radionuclides by double radionuclide autoradiography; (8) for radioactive materials with low level of radionuclides by fluorescence sensitization autoradiography; (9) in dissociative products by chromatographic autoradiography

  17. Sources to environmental radioactive contamination from nuclear activities in the former USSR

    International Nuclear Information System (INIS)

    Polikarpov, G.G.; Aarkrog, A.

    1993-01-01

    There is three major sites of radioactive environmental contamination in the former USSR: the Cheliabinsk region in the Urals, Chernobyl NPP in Ukraine and Novaya Zemlya in the Arctic Ocean. The first mentioned is the most important with regard to local (potential) contamination, the last one dominates the global contamination. A number of sites and sources are less well known with regard to environmental contamination. This is thus the case for the plutonium production factories at Tomsk and Dodonovo. More information on nuclear reactors in lost or dumped submarines is also needed. From a global point of view reliable assessment of the radioactive run-off from land and deposits of nuclear waste in the Arctic Ocean are in particular pertinent

  18. The total amounts of radioactively contaminated materials in forests in Fukushima, Japan

    Science.gov (United States)

    Hashimoto, Shoji; Ugawa, Shin; Nanko, Kazuki; Shichi, Koji

    2012-01-01

    There has been leakage of radioactive materials from the Fukushima Daiichi Nuclear Power Plant. A heavily contaminated area (≥ 134, 137Cs 1000 kBq m−2) has been identified in the area northwest of the plant. The majority of the land in the contaminated area is forest. Here we report the amounts of biomass, litter (small organic matter on the surface of the soil), coarse woody litter, and soil in the contaminated forest area. The estimated overall volume and weight were 33 Mm3 (branches, leaves, litter, and coarse woody litter are not included) and 21 Tg (dry matter), respectively. Our results suggest that removing litter is an efficient method of decontamination. However, litter is being continuously decomposed, and contaminated leaves will continue to fall on the soil surface for several years; hence, the litter should be removed promptly but continuously before more radioactive elements are transferred into the soil. PMID:22639724

  19. Immobilization of radioactive strontium in contaminated soils by phosphate treatment

    International Nuclear Information System (INIS)

    Kim, K.H.; Ammons, J.T.

    1990-01-01

    The feasibility of in situ phosphate- and metal- (calcium, aluminum, and iron) solution treatment for 90 Sr immobilization was investigated. Batch and column experiments were performed to find optimum conditions for coprecipitation of 90 Sr with Ca-, Al-, and Fe-phosphate compounds in contaminated soils. Separate columns were packed with artificially 85 Sr-contaminated acid soil as well as 90 Sr-contaminated soil from the Oak Ridge Reservation. After metal-phosphate treatment, the columns were then leached successively with either tapwater or 0.001 M CaCl 2 solution. Most of the 85 Sr coprecipitated with the metal phosphate compounds. Immobilization of 85 Sr and 90 Sr was affected by such factors as solution pH, metal and phosphate concentration, metal-to-phosphate ratio, and soil characteristics. Equilibration time after treatments also affected 85 Sr immobilization. Many technology aspects still need to be investigated before field applications are feasible, but these experiments indicate that phosphate-based in situ immobilization should prevent groundwater contamination and will be useful as a treatment technology for 90 Sr-contaminated sites. 15 refs., 3 figs., 1 tab

  20. Comparative study between radioactive contamination in milk powder by chernobyl accident [137Cs] and natural radioactivity [40K

    International Nuclear Information System (INIS)

    Navarrete, J.M.; Martinez, T.; Cabrera, L.

    2005-01-01

    After the Chernobyl accident in 1986, Mexico imported from an European country 28,000 Tons of contaminated milk powder with the fission product 137 CS. When the contamination was detected, the alarm among the authorities and population spread out very quick and of course the product was retired at once from the foodstuff market. Nevertheless, the public panic grew up in such a manner, that even the way to manage and to dispose safely this material, considered highly dangerous, was largely discussed. Now, about two decades ago from this event, a study has been performed to compare the level of radioactivity due to both radioisotopes present in one saved sample: the artificial contaminant 137 CS, beside the natural, all around present 40 K, in order to evaluate in a more realistic way how risky was the management, possible consumption, and final disposition of this nourishment. This paper considers results obtained within an uncertainty degree equal to ±5%, and set up conclusions by comparing artificial and natural radioactivity present in that contaminated milk powder.

  1. Dispersal of radioactivity by wildlife from contaminated sites in a forested landscape

    Energy Technology Data Exchange (ETDEWEB)

    Garten, C.T. [Oak Ridge National Lab., TN (United States). Environmental Sciences Div.

    1995-12-31

    Oak Ridge National Laboratory (ORNL) is located within the Valley and Ridge Physiographic Province of eastern Tennessee (USA). Wildlife populations have access to some radioactively contaminated sites at ORNL. Contaminated animals or animal nests within the Laboratory`s boundaries have been found to contain {sup 90}Sr or {sup 137}Cs on the order of 10{sup -2}-10{sup 4} Bq g{sup -1} and trace amounts of other radionuclides (including transuranic elements). Animals that are capable of flight and animals with behaviour patterns or developmental life stages involving contact with sediments in radioactive ponds, like benthic invertebrates, present the greatest potential for dispersal of radioactivity. The emigration of frogs and turtles from waste ponds also presents a potential for dispersal of radioactivity but over distances < 5 km. Mud-dauber wasps (Hymenoptera) and swallows (Hirundinidae) may transport radioactive mud for nest building, but also over relatively short distances (0.2-1 km). Movement by small mammals is limited by several factors, including physical barriers and smaller home ranges. Larger animals, like white-tailed deer (Odocoileus virginianus) are potential vectors of radioactivity due to their greater body size, longer life expectancy, and larger home range. Larger animals contain greater amounts of total radioactivity than smaller animals, but tissue concentrations of {sup 137}Cs generally decline with body size. (author).

  2. Contaminant interferences with SIMS analyses of microparticle impactor residues on LDEF surfaces

    International Nuclear Information System (INIS)

    Simon, C.G.; Batchelor, D.; Griffis, D.P.; Hunter, J.L.; Misra, V.; Ricks, D.A.; Wortman, J.J.

    1992-01-01

    Elemental analyses of impactor residues on high purity surface exposed to the low earth orbit (LEO) environment for 5.8 years on Long Duration Exposure Facility (LDEF) has revealed several probable sources for microparticles at this altitude, including natural micrometeorites and manmade debris ranging from paint pigments to bits of stainless steel. A myriad of contamination interferences were identified and their effects on impactor debris identification mitigated during the course of this study. These interferences included pre-, post-, and in-flight deposited particulate surface contaminants, as well as indigenous heterogeneous material contaminants. Non-flight contaminants traced to human origins, including spittle and skin oils, contributed significant levels of alkali-rich carbonaceous interferences. A ubiquitous layer of in-flight deposited silicaceous contamination varied in thickness with location on LDEF and proximity to active electrical fields. In-flight deposited (low velocity) contaminants included urine droplets and bits of metal film from eroded thermal blankets

  3. Radioactive contamination of animal bones by 90Sr

    International Nuclear Information System (INIS)

    Franic, Z.; Maracic, M.

    1996-01-01

    90 Sr has been regarded as the fission product of great potential hazard to living things because of the unique combination of its 28-y long half-life, the very energetic beta particle of its 90 Y daughter, and its general resemblance to calcium in metabolic processes. Therefore, due to chemical and metabolic similarity to calcium, bone is the critical organ for radioactive isotopes of strontium. The Department of Radiation Protection of the Institute for Medical Research and Occupational Health, has carried out radioactivity measurements of the food chain as part of an extended monitoring programme, since 1963. This includes systematic, long-term measurements of 90 Sr in long bones of some domestic animals (cows and pigs) while data on lamb bones exist for the very beginning of the investigated period, and for the period after the Chernobyl nuclear accident

  4. Characterization of freshwater mosses as indicators of radioactive contamination

    International Nuclear Information System (INIS)

    Beaugelin-Seiller, K.

    1994-01-01

    The necessity of indicators of freshwater contamination has developed the interest for aquatic mosses. From a fundamental point of view, studying the influence of some biotic and abiotic factors has permitted to better know the mechanisms of radionuclides accumulation by these bryophytes. From a radioecological point of view, simulating real cases of water contamination has allowed to give results a very interesting representativeness. The use of mosses as bio-indicators was applied for two in situ experiments, the results of which have been interpreted from those obtained in laboratory. Finally, an approach by a mathematical model has showed that it is possible to have, in a middle term, an evaluation tool of freshwater contamination, based on the radionuclides concentrations measured in aquatic mosses. (author). refs., 57 figs., 24 tabs

  5. Intervention strategies for the recovery of radioactive-contaminated environments

    International Nuclear Information System (INIS)

    Gutierrez, J.; Vazquez, C.

    2000-01-01

    Following an accident with environmental consequences, intervention may be necessary. The type of remedial actions and the strategy required will be dependent upon, inter alia, the phase and conditions within the contaminated scenario. Leaving aside the basic countermeasures (such as confinement, evacuation), which are based on internationally agreed Generic Intervention Levels (GIL's), the paper deals with intervention strategies leading to a return of the contaminated site to as close to normality as possible with the lowest social cost. The reduction of the damage from the existing contamination must be justified and optimised; the best strategy for applying recovery actions must be selected from a set of potential alternatives. A methodology for intervention strategies analysis, developed in the framework of CEC-CHECIR ECP-4 'Decontamination Strategies', is presented together with some examples of application. (author)

  6. Plant residues--a low cost, effective bioremediation treatment for petrogenic hydrocarbon-contaminated soil.

    Science.gov (United States)

    Shahsavari, Esmaeil; Adetutu, Eric M; Anderson, Peter A; Ball, Andrew S

    2013-01-15

    Petrogenic hydrocarbons represent the most commonly reported environmental contaminant in industrialised countries. In terms of remediating petrogenic contaminated hydrocarbons, finding sustainable non-invasive technologies represents an important goal. In this study, the effect of 4 types of plant residues on the bioremediation of aliphatic hydrocarbons was investigated in a 90 day greenhouse experiment. The results showed that contaminated soil amended with different plant residues led to statistically significant increases in the utilisation rate of Total Petroleum Hydrocarbon (TPH) relative to control values. The maximum TPH reduction (up to 83% or 6800 mg kg(-1)) occurred in soil mixed with pea straw, compared to a TPH reduction of 57% (4633 mg kg(-1)) in control soil. A positive correlation (0.75) between TPH reduction rate and the population of hydrocarbon-utilising microorganisms was observed; a weaker correlation (0.68) was seen between TPH degradation and bacterial population, confirming that adding plant materials significantly enhanced both hydrocarbonoclastic and general microbial soil activities. Microbial community analysis using Denaturing Gradient Gel Electrophoresis (DGGE) showed that amending the contaminated soil with plant residues (e.g., pea straw) caused changes in the soil microbial structure, as observed using the Shannon diversity index; the diversity index increased in amended treatments, suggesting that microorganisms present on the dead biomass may become important members of the microbial community. In terms of specific hydrocarbonoclastic activity, the number of alkB gene copies in the soil microbial community increased about 300-fold when plant residues were added to contaminated soil. This study has shown that plant residues stimulate TPH degradation in contaminated soil through stimulation and perhaps addition to the pool of hydrocarbon-utilising microorganisms, resulting in a changed microbial structure and increased alkB gene

  7. Some aspects of radioactive contamination and decontamination of the Chernobyl' NPP accident zone territory

    International Nuclear Information System (INIS)

    Samojlenko, Yu.N.; Nad''yarnykh, G.V.; Teplitskij, A.L.; Shilin, S.A.

    1989-01-01

    Data are presented on the radioactive contamination of the 30-km zone, on the radionuclide (RN) distribution in soils and on the RN migration in grounds. During 1986-1988 were tested over 20 techniques for territory decontamination and were found out the most optimal ones. The first stage of decontamination was removal of an upper contaminated soil layer. The second stage was prolonged chemical fixation of dusting decontaminated soil areas. 3 tabs

  8. Evolution of radioactive dose rates in fresh sediment deposits along coastal rivers draining Fukushima contamination plume

    OpenAIRE

    Evrard, Olivier; Chartin, Caroline; Onda, Yuichi; Patin, Jeremy; Lepage, Hugo; Lef?vre, Ir?ne; Ayrault, Sophie; Ottl?, Catherine; Bont?, Philippe

    2013-01-01

    Measurement of radioactive dose rates in fine sediment that has recently deposited on channel bed-sand provides a solution to address the lack of continuous river monitoring in Fukushima Prefecture after Fukushima Dai-ichi nuclear power plant (FDNPP) accident. We show that coastal rivers of Eastern Fukushima Prefecture were rapidly supplied with sediment contaminated by radionuclides originating from inland mountain ranges, and that this contaminated material was partly exported by typhoons t...

  9. Decontamination methods of the vegetables contaminated with radioactive materials from Fukushima Daiichi Nuclear Power Station accident

    International Nuclear Information System (INIS)

    Nishizawa, Kunihide; Shiba, Kazuhiro

    2011-01-01

    Among agricultural products, vegetables contaminated with radioactive materials were examined to find a practical decontamination method. For spinach, washing by running water or hot water, and by ultrasonic or shower washing were tested. Furthermore, chemical method using detergent acid, alkaline salt was examined. High removal efficiency was obtained for iodine 131 using sodium hydrosulfate. For visual observation, IP imaging and scanning electromagnetic method were used to find spots and plane contamination. (S. Ohno)

  10. Synthesis and evaluation of radioactive and fluorescent residualizing labels for identifying sites of plasma protein catabolism

    International Nuclear Information System (INIS)

    Maxwell, J.L.; Baynes, J.W.; Thorpe, S.R.

    1986-01-01

    Inulin and lactose were each coupled to tyramine by reductive amination with NaBH 3 CN and the tyramine then labeled with 125 I. Dilactitol- 125 I-tyramine (DLT) and inulin- 125 I-tyramine (InTn) were coupled by reductive amination and cyanuric chloride, respectively, to asialofetuin (ASF), fetuin and rat serum albumin (RSA). Attachment of either label had no effect on the circulating half-lives of the proteins. Radioactivity from labeled ASF was recovered in rat liver (> 90%) by 1 h post-injection and remained in liver with half-lives of 2 and 6 days, respectively, for the DLT and InTn labels. Whole body recoveries of radioactivity from DLT- and InTn labels. Whole body recoveries of radioactivity from DLT- and InTn-labeled RSA were 5 and 6.5 days, respectively, again indicating that the larger glycoconjugate label residualized more efficiently in cells following protein degradation. (Lactitol) 2 -N-CH 2 -CH 2 -NH-fluroescein (DLF) was also coupled to ASF by reductive amination and recovered quantitatively in liver at 1 h post-injection. Native ASF was an effective competitor for clearance of DLF-ASF from the circulation. Fluorescent degradation products were retained in liver with a half-life of 1.2 days. Residualizing fluorescent labels should be useful for identification and sorting of cells active in the degradation of plasma proteins

  11. Long-term residual radioactivity in an intermediate-energy proton linac

    CERN Document Server

    Blaha, J; Silari, M; Vollaire, J

    2014-01-01

    A new 160 MeV H−H− linear accelerator (LINAC4) is being installed at CERN to replace the present 50 MeV LINAC2 as proton injector of the PS Booster (PSB). During operation, the accelerator components will be activated by the beam itself and by the secondary radiation field. Detailed Monte Carlo simulations, for various beam energies and several decay times, were performed to predict the residual radioactivity in the main accelerator components and to estimate the residual dose rate inside the tunnel. The results of this study will facilitate future dismantling, handling and storage of the activated parts and consequently minimize the radiation dose to involved workers. The component activation was also compared with the exemption limits given in the current Swiss legislation and to the CERN design values, in order to make predictions for the future storage and disposal of radioactive waste. The airborne radioactivity induced by particles escaping the beam dump and the activation of the beam dump cooling w...

  12. Long-term residual radioactivity in an intermediate-energy proton linac

    Science.gov (United States)

    Blaha, J.; La Torre, F. P.; Silari, M.; Vollaire, J.

    2014-07-01

    A new 160 MeV H- linear accelerator (LINAC4) is being installed at CERN to replace the present 50 MeV LINAC2 as proton injector of the PS Booster (PSB). During operation, the accelerator components will be activated by the beam itself and by the secondary radiation field. Detailed Monte Carlo simulations, for various beam energies and several decay times, were performed to predict the residual radioactivity in the main accelerator components and to estimate the residual dose rate inside the tunnel. The results of this study will facilitate future dismantling, handling and storage of the activated parts and consequently minimize the radiation dose to involved workers. The component activation was also compared with the exemption limits given in the current Swiss legislation and to the CERN design values, in order to make predictions for the future storage and disposal of radioactive waste. The airborne radioactivity induced by particles escaping the beam dump and the activation of the beam dump cooling water circuit were also quantified. The aim of this paper is to provide data of sufficiently general interest to be used for similar studies at other intermediate-energy proton accelerator facilities.

  13. Long-term residual radioactivity in an intermediate-energy proton linac

    International Nuclear Information System (INIS)

    Blaha, J.; La Torre, F.P.; Silari, M.; Vollaire, J.

    2014-01-01

    A new 160 MeV H − linear accelerator (LINAC4) is being installed at CERN to replace the present 50 MeV LINAC2 as proton injector of the PS Booster (PSB). During operation, the accelerator components will be activated by the beam itself and by the secondary radiation field. Detailed Monte Carlo simulations, for various beam energies and several decay times, were performed to predict the residual radioactivity in the main accelerator components and to estimate the residual dose rate inside the tunnel. The results of this study will facilitate future dismantling, handling and storage of the activated parts and consequently minimize the radiation dose to involved workers. The component activation was also compared with the exemption limits given in the current Swiss legislation and to the CERN design values, in order to make predictions for the future storage and disposal of radioactive waste. The airborne radioactivity induced by particles escaping the beam dump and the activation of the beam dump cooling water circuit were also quantified. The aim of this paper is to provide data of sufficiently general interest to be used for similar studies at other intermediate-energy proton accelerator facilities

  14. Radioactive contamination of the environmental samples in Hanoi in 1989

    International Nuclear Information System (INIS)

    Dang Huy Uyen; Bui Van Loat; Dang Phuong Nam; Cao Anh Duc; Pham Quang Dien; Nguyen Hao Quang

    1990-01-01

    More than 30 environmental samples from soil, paddy, rice, fruits, vegetables and beans, sesame, tea, bananas, fishes at Hanoi markets in 1989 were analysed by gamma ray spectrometry with the low background system for studying natural and artificial radioactive elements. Among several samples from Hanoi in such kind as cultivated soils, tea, dried bamboo shoots, isotope Cs 137 that used be generated from nuclear explosives was found with contents (30 - 1000) x 10 -5 Bq/g; Cs 137 contents in Japanese rice (0.4 - 3) x 10 -5 Bq/g. Cs 137 is radioactive so Cs 137 contents in Vietnamese rice are 300 times higher than Cs 137 contents in Japanese rice but they are hundred times lower than international standard. Among vegetables, fruits, shrimps, fishes in Hanoi markets, artificial isotopes were not found and natural isotopes were few. Even radioactive daughter and granddaughter in uranium series in potatoes were not found. In some samples K 40 was also appeared, for example in cultivated soils (0.78 Bq/g), in dried bamboo shoots (0.73 Bq/g). (author). 2 refs., 3 figs

  15. Monitoring Potential Transport of Radioactive Contaminants in Shallow Ephemeral Channels

    International Nuclear Information System (INIS)

    Miller Julianne J.; Mizell Steve A.; Nikolich George; Campbell Scott A.

    2012-01-01

    The U.S. Department of Energy (DOE) National Nuclear Security Administration (NNSA), Nevada Site Office (NSO), Environmental Restoration Soils Activity has authorized the Desert Research Institute (DRI) to conduct field assessments of potential sediment transport of contaminated soil from Corrective Action Unit (CAU) 550, Area 8 Smoky Contamination Area (CA), during precipitation runoff events. CAU 550 includes Corrective Action Sites (CASs) 08-23-03, 08-23-04, 08-23-06, and 08-23-07; these CASs are associated with tests designated Ceres, Smoky, Oberon, and Titania, respectively.

  16. Equipment for measuring contamination of hands with radioactive material

    International Nuclear Information System (INIS)

    Erban, J.; Kleinbauer, K.; Husak, V.; Grigar, O.

    1986-01-01

    The claimed device consists of a scintillation detector mounted in a shielding case consisting of rings. The shielding case is provided with a cavity with an inlet opening lined with polyethylene foil. The cavity shape, shielding and replaceable foil guarantee minimizing the interfering effect of radiation sources in the vicinity and of contamination of the device. Gradually inserting the hand in the cavity or suitably placing the hand can locate contamination of the hand surface. The sensitivity of the device for 125 I and 99 Tc is 200-times higher than that of Geiger-Mueller counter instruments. (M.D.)

  17. Disposal of the radioactive contaminated soils from the NPP site

    International Nuclear Information System (INIS)

    Matusek, I.; Plsko, J.; Sajtlava, M.; Hulla, J.; Kovacs, T.

    2004-01-01

    Disposal of contaminated soils at site of NPP is one of the most important task within the frame of research and development tasks of the NPP decommissioning. The works within this field can be seen in several areas. Considered soil activity monitoring, observation of its geo-technical and geo-chemical parameters, volume balance, research of the radio nuclides behaviour in the soil and simulation of their influence on the surrounding environment with special emphasis on underground water, project studies and construction of the disposal facility for contaminated soils. This work presents overview of gained results in the mentioned areas of the research and development. (author)

  18. Radioactive Contamination Near Natural Uranium - Graphite - Gas Reactors

    International Nuclear Information System (INIS)

    Chassany, J.; Pouthier, J.

    1967-01-01

    The authors give the results of numerous assessments of contamination in connection with reactors in operation during maintenance; reactors shut down during overhaul and repair work (coolants, exchangers, interior of the tank, etc.) ; and accidents in the cooling circuit and ruptured cladding. They show that, except in special cases, it is mainly activation products that predominate. Moreover, after eight years of operation the points where contamination likely to give considerable dose rates accumulates remain very localized, and there has been no need to reinforce personnel protection measures. (author) [fr

  19. Monitoring pesticides residues and contaminants for some leafy vegetables at the market level

    International Nuclear Information System (INIS)

    Ibrahim, A. B. H.

    2004-03-01

    Pesticide residues and contaminants in selected leafy vegetables, namely (lettuce, garden rocket and salad onion) were monitored at market level in Riyadh City in Saudi Arabia, during the period june to july 2001. Fifteen samples of vegetables from the City vegetable market of Riyadh were collected and subjected to multi-pesticide residue detection and analysis by gas chromatography with mass spectrometer and electron capture detectors (GC/MS,ECD). Results of sample extracts analysis showed that the two vegetables of: garden rocket and salad onion contain pesticide residues and contaminants which have no Maximum Residue Limits (MRL) prescribed by Codex Alimentarius Commission (CAC) collaborate with World Health and Food and Agriculture Organizations (WHO/FAO). Whereas lettuce vegetable was found free of any identified pesticide residues or contaminants. Garden rocket was shown to contain dibutyl phthalate (0.04 ppm)-steryl chloride (0.02 ppm) tridecane (0.06 ppm)-hexadecane (0.07 ppm)-BIS (ethylhexyl) phthalate (0.006 ppm) and pyridinium, 1-hexyl chloride (0.01 ppm). The salad onion was found to contain 9-octadecanamide (0.13 ppm)-tridecane (0.15 ppm) and tetradecane (0.16 ppm). There are no established MRL s for these pesticides and contaminants detected in garden rocket and salad onion, although when impacts on human health were reviewed some of them were found probably hazardous. (Author)

  20. Radioactive contamination of some rubber or plastic surfaces by fission products. Decontamination tests

    International Nuclear Information System (INIS)

    Mestre, E.; Sautiez, N.

    1957-10-01

    With the objective of notably addressing the contamination and decontamination of gloves and floor covering, this report first presents some characteristics of contaminating radioactive materials (nature, physical and chemical condition), of contaminated surfaces (surface condition, surface nature), and of decontamination processes (physical, chemical or mechanical action). It describes the operational modality implemented to test decontamination processes on various glove or flooring materials: sample preparation, counting, decontamination, reproducibility of decontamination tests, results in terms of activity reduction. It more precisely describes the tested samples: short gloves, gloves from glove boxes, floor and wall coverings. Results are presented and discussed in terms of sample susceptibility to contamination, and of decontamination, but also for re-contamination tests after a Nab-based decontamination (susceptibility to contamination, decontamination gain)

  1. On-site radioactive soil contamination at the Andreeva Bay shore technical base, Northwest Russia.

    Science.gov (United States)

    Reistad, O; Dowdall, M; Selnaes, Ø G; Standring, W J F; Hustveit, S; Steenhuisen, F; Sørlie, A

    2008-07-01

    The radioactive waste (RAW) storage site at Andreeva Bay in the Russian Northwest has experienced radioactive contamination both as a result of activities carried out at the site and due to incidents that have occurred there in the past such as accidental releases of radioactive materials. The site is an interesting case study for decommissioning due to the extremely large amounts of radioactivity present at the site and the conditions under which it is stored; very little has been previously published in the scientific literature about this site. This paper complements the paper describing dose rates at Andreeva Bay which is published in this issue of Journal of Environmental Radioactivity by the same authors. This study presents new data related to the activity concentrations of (137)Cs and (90)Sr in surface soils and measurements of alpha- and beta-particle fluxes taken at different areas around the site. Limited data on 60Co is also presented. The results of the study indicate that the main areas of site contamination are associated with the former spent nuclear fuel storage facility at Building 5, due to accidental discharges which began in 1982. Substantial contamination is also observed at the solid radioactive waste storage facilities, probably due to the ingress of water into these facilities. More than 240 samples were measured: maximum contamination levels were 1 x 10(6)Bq/kg (137)Cs (mean value 4.1 x 10(5)Bq/kg) and 4 x 10(6)Bq/kg (90)Sr (mean value 1.2 x1 0(5)Bq/kg). Localised patches of alpha and beta contamination were also observed throughout the site.

  2. Calculation of Radioactivity Concentration on Cover Depth of Contaminated Zone for Self-Disposal

    Energy Technology Data Exchange (ETDEWEB)

    Koo, Daeseo; Sung, Hyun-Hee; Kim, Gye-Nam; Kim, Seung-Soo; Kim, Ilgook; Han, Gyu Seong; Choi, Jong-Won [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2015-10-15

    We have a lot of uranium contaminated soil and concrete wastes owing to dismantlement of uranium conversion facility. There are several radioactive material disposal methods such as regulation exemption, decontamination and long term storage. It is necessary for us to perform permanent disposal of these wastes. To acquire radiation dose under self-disposal from them, the study on decontamination of some uranium contaminated soil and concrete wastes was performed using electrokinectic-electrodialytic. In this study, we evaluated radiation dose on the cover depth of contaminated zone from the wastes under radiation dose limit using RESRAD Version 6.5. At first, the calculation of the radiation dose on the wastes of contaminated zone are carried out. The second, the cover depth of contaminated zone are analyzed. The application to self-disposal of contaminated zone are also analyzed. To acquire radiation dose under self-disposal from uranium contaminated soil and concrete wastes, we decontaminated some uranium contaminated soil and concrete wastes using electrokinectic-electrodialytic. To perform self-disposal of the quantity (30,000kg) of contaminated zone, the calculating conditions for radiation dose on the cover depth of contaminated zone are as follows. The area of contaminated zone is 10m{sup 2}. The thickness of contaminated zone is 2 m. The cover depth of contaminated zone are analyzed. The application to self-disposal of contaminated zone are also analyzed. Therefore, as the cover depth increases, the uranium concentration has an increasing trend. It realize that the cover depth of contaminated zone is adequate < 2m at the quantity(30,000kg) of contaminated zone. As the cover depth increases, the uranium concentration has a decreasing trend. As the cover depth increases, the radiation dose(residents) has also a decreasing trend.

  3. Multiple methods for assessing the dose to skin exposed to radioactive contamination

    International Nuclear Information System (INIS)

    Dubeau, J.; Heinmiller, B.E.; Corrigan, M.

    2017-01-01

    There is the possibility for a worker at a nuclear installation, such as a nuclear power reactor, a fuel production facility or a medical facility, to come in contact with radioactive contaminants. When such an event occurs, the first order of business is to care for the worker by promptly initiating a decontamination process. Usually, the radiation protection personnel performs a G-M pancake probe measurement of the contamination in situ and collects part or all of the radioactive contamination for further laboratory analysis. The health physicist on duty must then perform, using the available information, a skin dose assessment that will go into the worker's permanent dose record. The contamination situations are often complex and the dose assessment can be laborious. This article compares five dose assessment methods that involve analysis, new technologies and new software. The five methods are applied to 13 actual contamination incidents consisting of direct skin contact, contamination on clothing and contamination on clothing in the presence of an air gap between the clothing and the skin. This work shows that, for the cases studied, the methods provided dose estimates that were usually within 12% (1σ) of each other, for those cases where absolute activity information for every radionuclide was available. One method, which relies simply on a G-M pancake probe measurement, appeared to be particularly useful in situations where a contamination sample could not be recovered for laboratory analysis. (authors)

  4. Manual for implementing residual radioactive material guidelines using RESRAD, Version 5.0

    Energy Technology Data Exchange (ETDEWEB)

    Yu, C.; Zielen, A.J.; Cheng, J.J. [and others

    1993-09-01

    This manual presents information for implementing US Department of Energy (DOE) guidelines for residual radioactive material. It describes the analysis and models used to derive site-specific guidelines for allowable residual concentrations of radionuclides in soil and the design and use of the RESRAD computer code for calculating doses, risks, and guideline values. It also describes procedures for implementing DOE policy for reducing residual radioactivity to levels that are as low as reasonably achievable. Two new pathways, radon inhalation and soil ingestion, have been added to RESRAD. Twenty-seven new radionuclides have also been added, and the cutoff half-life for associated radionuclides has been reduced to six months. Other major improvements to the RESRAD code include the ability to run sensitivity analyses, the addition of graphical output, user-specified dose factors, updated databases, an improved groundwater transport model, optional input of a groundwater concentration and a solubility constant, special models for tritium and carbon-14, calculation of cancer incidence risk, and the use of a mouse with menus.

  5. Manual for implementing residual radioactive material guidelines using RESRAD, Version 5.0

    International Nuclear Information System (INIS)

    Yu, C.; Zielen, A.J.; Cheng, J.J.

    1993-09-01

    This manual presents information for implementing US Department of Energy (DOE) guidelines for residual radioactive material. It describes the analysis and models used to derive site-specific guidelines for allowable residual concentrations of radionuclides in soil and the design and use of the RESRAD computer code for calculating doses, risks, and guideline values. It also describes procedures for implementing DOE policy for reducing residual radioactivity to levels that are as low as reasonably achievable. Two new pathways, radon inhalation and soil ingestion, have been added to RESRAD. Twenty-seven new radionuclides have also been added, and the cutoff half-life for associated radionuclides has been reduced to six months. Other major improvements to the RESRAD code include the ability to run sensitivity analyses, the addition of graphical output, user-specified dose factors, updated databases, an improved groundwater transport model, optional input of a groundwater concentration and a solubility constant, special models for tritium and carbon-14, calculation of cancer incidence risk, and the use of a mouse with menus

  6. Characterization of radioactive contaminants and water treatment trials for the Taiwan Research Reactor's spent fuel pool

    International Nuclear Information System (INIS)

    Huang, Chun-Ping; Lin, Tzung-Yi; Chiao, Ling-Huan; Chen, Hong-Bin

    2012-01-01

    Highlights: ► Deal with a practical radioactive contamination in Taiwan Research Reactor spent fuel pool water. ► Identify the properties of radioactive contaminants and performance test for water treatment materials. ► The radioactive solids were primary attributed by ruptured spent fuels, spent resins, and metal debris. ► The radioactive ions were major composed by uranium and fission products. ► Diatomite-based ceramic depth filter can simultaneously removal radioactive solids and ions. - Abstract: There were approximately 926 m 3 of water contaminated by fission products and actinides in the Taiwan Research Reactor's spent fuel pool (TRR SFP). The solid and ionic contaminants were thoroughly characterized using radiochemical analyses, scanning electron microscopy equipped with an energy dispersive spectrometer (SEM-EDS), and inductively coupled plasma optical emission spectrometry (ICP-OES) in this study. The sludge was made up of agglomerates contaminated by spent fuel particles. Suspended solids from spent ion-exchange resins interfered with the clarity of the water. In addition, the ionic radionuclides such as 137 Cs, 90 Sr, U, and α-emitters, present in the water were measured. Various filters and cation-exchange resins were employed for water treatment trials, and the results indicated that the solid and ionic contaminants could be effectively removed through the use of <0.9 μm filters and cation exchange resins, respectively. Interestingly, the removal of U was obviously efficient by cation exchange resin, and the ceramic depth filter composed of diatomite exhibited the properties of both filtration and adsorption. It was found that the ceramic depth filter could adsorb β-emitters, α-emitters, and uranium ions. The diatomite-based ceramic depth filter was able to simultaneously eliminate particles and adsorb ionic radionuclides from water.

  7. Radioactive Contamination Tenacity on Building Substrate – 17417

    Energy Technology Data Exchange (ETDEWEB)

    Demmer, Rick; Boxall, Colin

    2017-01-01

    Radiological decontamination is an essential enterprise that has become more important over the last four decades due to unfortunate accidents and the threat of terrorist actions. Decontamination can be an effective, beneficial alternative for the cleanup of radiological contamination events; however, the costs and benefits need to be balanced against those for complete removal and demolition of contaminated areas or facilities. Demolition and removal are often the first options considered in such circumstances as decontamination may be thought of as slow and costly. Decontamination has advantages, including significant waste reduction over demolition. In areas with buildings of cultural or societal importance, demolition may not be an option. Three decontamination evaluation test series are the focus of this article: SIMCON 1 and 2 (i.e., simulated contamination), and Urban RDD (radiological dispersal device, i.e., a dirty bomb detonation). These test series revealed that different contaminants respond differently during decontamination. This was found to be true with both SIMCON and Urban RDD simulant tests. SIMCON 2 especially demonstrated that chemically different contaminants respond differently to different decontamination methods: cesium appears to be less tenacious (more easily removed) than zirconium using chemical methods. These differences were underscored by the Urban RDD tests where americium and cobalt tended to precipitate on high pH surfaces (such as concrete), making them easier to remove, while cesium and strontium were essentially unaffected by surface pH and were imbibed more strongly into the substrate pore structure. While authorities argue over the contributions of contaminant chemistry and substrate morphology, the clear answer is that each has a contribution to the tenacity of a contaminant. Knowing how these characteristics interact will make us better at decontamination in the field. This knowledge refutes the efforts of perhaps well

  8. On development of systematical recommendations for the appropriate decision-making during relief works of radioactive contaminated areas

    International Nuclear Information System (INIS)

    Bobrov, A.F.; Grachev, M.I.; Andrianov, K.N.; Grinev, M.P.; Savkin, M.N.

    1994-01-01

    The basic principle and decision-making structure on the relief of radioactive contaminated areas on the basic of the cost-benefit analysis are presented. Dose criteria and classification of radioactive contaminated areas are discussed. The examples of multifactorial analysis and hierarchy analysis method are given. 2 tabs

  9. Residual radioactivity in the vicinity of formerly utilized MED/AEC sites

    International Nuclear Information System (INIS)

    Haywood, F.F.; Goldsmith, W.A.

    1980-01-01

    As demand for uranium and thorium was accelerated during the 1940's, services of chemical and metallurgical firms and major research facilities were contracted as needed by the Manhattan Engineer District (MED). A lack of documentation of the radiological status at the time contracts were terminated at these facilities led the Department of Energy (DOE), and its predecessor the Energy Research and Development Administration (ERDA), to develop a major radiological resurvey program to fill this information void. A combination of aerial and ground-level radiological monitoring teams were utilized to identify and assess off-site radioactivity. Results from comprehensive aerial surveys provide the approximate areal extent of elevated radiation levels on the ground. These aerial survey results led to two types of ground-level surveys: (1) gamma-ray scanning on foot or from a motorized vehicle (mobile lab based system) to pinpoint the location of residual radioactivity; and (2) compehensive radiological surveys to determine the amount and type of materials present on specific parcels of private and public property identified during the scanning. This type of investigation was initiated in 1978 and has been successful in identifying and assessing the potential radiation hazard from property on which materials bearing natural radioactivity have been found. This paper contains a description of the techniques used to find and evaluate radioactive material displaced outside the boundaries of a formerly utilized site

  10. The major regularities of the air radioactive contamination of Belarus territory after the Chernobyl accident

    International Nuclear Information System (INIS)

    Konoplya, E. F.; Mironov, V. P.; Drugachenok, M. A.; Kudryashov, V.P; Grushevich, L.E; Adamovich, A.A.

    2001-01-01

    In the first days after the Chernobyl accident the radioactivity of surface air in different regions of Belarus has increased in tens and hundred thousand time. The regular control of air radioactive contamination in the zone of alienation and nearest to it is carried out from the end 1989. The radioactive air monitoring carried out in territories with various contamination density (from 0,2 up to 9,6 MBq/m 2 on Cs-137). The measurements of the Cs-137 contents in ashes of air sampler filters were carried out by gamma - spectrometer ADCAM-300 MCA. The measurement of the Pu-240,239 and Sr-90 contents was carried out by usual radiochemical techniques. The used techniques and equipment allow to define in a sample of the minimal activity: Pu-239,240 - 0,001 Bq, Cs-137 - 0,5 Bq, Sr-90 - 0,1 Bq. The initial contamination of ground happened a near zone within approximately first 2 weeks after accident. Since the end of May, 1986 till present time the air radioactive contamination is formed under action of processes of secondary wind rise and carry of radioactive particles with contaminated territories, which depends from a number factors of both natural and anthropogenous origin. The relations of Pu-238/Pu-239 and Sr-90/Pu-239 in aerosol particles practically coincide with the same relations in fuel blown up reactor. The ratio of Cs-137/Pu-239 activities in aerosols considerably exceeds the resettlement ratio for fuel. Strontium and plutonium are in structure of fuel particles, and cesium aerosol have other origin. The analysis of changes annual radioisotopes concentration in air of towns of Belarus specifies existence of the tendency to slow decrease of contamination of atmosphere by radioisotopes of industrial origins. The basic tendency of formation of air radioactive contamination is determined by the contents of a dust at surface layer of an atmosphere and its specific activity. Annual average dust content of air in a zone resettlement was least and made about 10 mk g

  11. Conceptual framework and technical basis for clearance of materials with residual radioactivity

    International Nuclear Information System (INIS)

    Chen, S.Y.

    1997-01-01

    The primary impediment to the release of materials containing residual radioactivity from a controlled environment is the lack of a suitable framework within which release standards can be developed. Recently, the 'risk-based' approach has been proposed as an appropriate means of setting standards. The term 'clearance' has been introduced by the International Atomic Energy Commission as a regulatory process for releasing radioactive materials posing trivial risks. A 'trivial' risk level has been determined to be on the order of 10[sup -6] to 10[sup -7] annual risk to an exposed individual, and a population risk of no more than 0.1 annually. Under these strict constraints, exposure scenarios may account for processing, disposal, and product end-use of materials. This paper discusses these scenarios and also describes the technical basis for deriving release levels under the suggested risk (or dose) constraints

  12. Analysis of Radioactivity Contamination Level of Kartini Reactor Efluen Gas to the Environment

    International Nuclear Information System (INIS)

    Suratman; Purwanto; Aminjoyo, S

    1996-01-01

    The analysis of radioactivity contamination level of Kartini reactor efluen gas to the environment has been done from 13-10-'95 until 8-2-'96. The aim of this research is to determine the radioactivity contamination level on the environment resulted from the release of Kartini reactor efluen gas and other facilities at Yogyakarta Nuclear Research Centre through stack. The analysis methods is the student t-test, the first count factor test and the gamma spectrometry. The gas sampling were carried out in the stack reactor, reactor room, environment and in other room for comparison. Efluen gas was sucked through a filter by a high volume vacuum pump. The filter was counted for beta, gamma and alpha activities. The radioactivity contamination level of the efluen gas passing through the stack to the environment was measured between 0.57 - 1.34 Bq/m3, which was equal to the airborne radioactivity in environment between 0.69 - 1.12 Bq/m3. This radioactivity comes from radon daughter, decay products result from the natural uranium and thorium series of the materials of the building

  13. Assessment of radioecological situation of a site contaminated by technologically enhanced natural radioactivity in Croatia

    International Nuclear Information System (INIS)

    Marovic, G.; Sencar, J.

    1999-01-01

    Radioactivity contamination originating from the coal fired power plant and its waste dumps located in a bay of the Adriatic which is due to geographical characteristics sensitive to any kind of pollution including radioactivity is discussed. Investigations of coal used in regular plant operation and of solid incombustile ash and slag showed increased concentrations of natural radioactivity which may cause general environmental contamination of the bay as well as contamination of the marine environment of this part of Croatian Adriatic. There are two coal slag and ash piles, one of them was closed and covered by soil and the other is a still operating pile. The location of both piles presents a considerable environmental problem: situated close to the seaside, slag and ash are accumulating in the littoral zone and, in the case of operating pile, are being filled up directly into the sea. The aim of this study was to determine the radioactivity level at the ash and slag deposits and to assess the risk of increased radioactivity for the inhabitants of the nearby urban area, for the plant workers and general environment of the bay including the marine environment of this part of the Croatian Adriatic. (author)

  14. Radioactive contamination of the forests of southern Poland and Finland

    International Nuclear Information System (INIS)

    Jasinska, H.; Kozak, K.; Mietelski, J.W.; Barszcz, J.; Greszta, J.

    2004-01-01

    Experimental data of caesium and ruthenium radioactivity in chosen parts of forest ecosystems in Finland and Southern Poland are presented and compared. Measurements were performed with a low-background gamma-rays spectrometer with the Ge(Li) detector. The maximum caesium 137 activity in litter from Poland is 2.5 kBq, in that from Finland 3.9 kBq, in spruce needles it is 0.4 kBq (Poland), 0.9 kBq (Finland) and in fern leaves it is as high as 15.9 kBq per kg of dry mass in one sample from Poland. (author)

  15. GIS-application for analysis of risk of radioactive contamination

    International Nuclear Information System (INIS)

    Baklanov, A.; Rigina, O.; Elyuchnikova, E.; Nazarenko, L.

    1995-01-01

    The main task of the international project Kolanet is the establishment of an information system for quick response on radiation accidents on the Kola peninsula. Along with a monitoring system, the response system includes a system for forecasting of possible consequences of an accident, based on several computer programs. As a first task of the project a data base and a map of the risk objects have been established. The data base includes information on nuclear ships and nuclear facilities, together with data on nuclear explosions, burials and dumping of radioactive wastes. 9 refs., 3 figs

  16. Prevention of radioactive contamination in the manufacture of phosphate fertilizers

    International Nuclear Information System (INIS)

    Romero G, E.T.

    1995-01-01

    In this work was studied the separation of uranium from the phosphate rock to decrease the level of radioactivity in the phosphate fertilizers, this prevents the redistribution of uranium in the environment. The uranium leaching conditions from phosphate rock were estimated using alkaline solutions. The changes in the natural phosphate rock after leaching were studied. The amenability to separate the uranium from phosphate rock with ammonium carbonate / bicarbonate solution was determined. The uranium extraction was approximately 40%. The leaching conditions showed high selectivity for uranium without changes in the ore structure. The bulk ore was not dissolved. (Author)

  17. Treatment techniques for the removal of radioactive contaminants from drinking water

    International Nuclear Information System (INIS)

    Logsdon, Gary S.

    1978-01-01

    Maximum contaminant levels have been set for radioactive contaminants, as required by the Safe Drinking Water Act (PL 93-523). Treatment techniques are available for removing radium and beta-gamma emitters. Presently-used methods of removing radium-226 are precipitative lime softening (80-90% removal) ion exchange softening (95% removal) and reverse osmosis (95% removal). The 5 p Ci/l limit for radium can be met with conventional technology for raw waters in the 5-100 p Ci/l concentration range. Treatment for removal of beta or gamma emitters must be based upon chemical rather than radioactive characteristics of the contaminant. Reverse osmosis can remove a broad spectrum of ions and molecules from water, so it is the process most likely to be used. The maximum contaminant level for beta and gamma radioactivity is an annual dose equivalent to the total body or any organ not to exceed 4 m rem/year. The fate of radionuclides after removal from drinking water should be considered. Presently radium is disposed with other process wastes at softening plants removing radium. Confinement and disposal as a radioactive waste would be very expensive. (author)

  18. The analysis of the level of radioactive contamination of agricultural lands in Mogilev region [Belarus

    International Nuclear Information System (INIS)

    Komleva, S.M.

    2010-01-01

    In the conditions of the Republic of Belarus there was analyzed the present level of radioactive situation and contamination of areas of agricultural companies with radiocesium at in Mogilev region. There were suggested methodical approaches on organizing the use of the lands in such a way as to get the minimum content of radionuclides in the manufactured products

  19. Radioactive contamination of soil-vegetation cover in some southern areas of Semipalatinsk test site

    International Nuclear Information System (INIS)

    Tuleubaev, B.A.; Zharikov, S.K.

    2001-01-01

    The nature of radioactive contamination of meadow-pasture lands in the south of the Semipalatinsk test site (STS) has been studied using experimental data. Individual parameters of radionuclide transport from soil into plants depending upon soil type and sub-type, extent of land use for hay-making and pasturing, and other nature-climatic and anthropogenic factors have been determined. (author)

  20. Development of Radioactive Substance Contamination Diffusion Preventive Equipment for a Hot cell

    International Nuclear Information System (INIS)

    Choo, Yong Sun; Kim, Do Sik; Baik, Seung Je; Yoo, Byung Ok; Kim, Ki Ha; Lee, Eun Pyo; Ahn, Sang Bok; Ryu, Woo Seok

    2009-01-01

    The hot cell of irradiated materials examination facility (IMEF), which has been operating since 1996, is generally contaminated by the radioactive nuclides of irradiated nuclear fuels and structural steels like Cs-137, Co-60, Co-134 and Ru-106. Especially Cs-137 is a main contaminated radioactive isotope which is easily moved here and there due to air flow in the hot cell, water-soluble, extremely toxic, and has a half-life of 30.23 years. To repair or fix the abnormal function of test apparatus installed in the hot cell, the maintenance door, so called a rear door and located at an intervention area, is opened to enter the hot cell inside. In a moment of opening the maintenance door, dirty air diffusion from the hot cell to an intervention area could be occurred in spite of increasing the rpm of exhaust fan to maintain much low under pressure, but an adjacent area to a maintenance door, i.e. intervention area, is very severely contaminated due to the unpredictable air flow. In this paper, the development of the radioactive substance contamination diffusion preventive equipment for a hot cell is studied to prevent dirty and toxic gaseous radioactive nuclides diffusion from a hot cell and installed at an intervention area of IMEF

  1. Mesoscale modelling of radioactive contamination formation in Ukraine caused by the Chernobyl accident

    International Nuclear Information System (INIS)

    Talerko, Nikolai

    2005-01-01

    This work is devoted to the reconstruction of time-dependent radioactive contamination fields in the territory of Ukraine in the initial period of the Chernobyl accident using the model of atmospheric transport LEDI (Lagrangian-Eulerian DIffusion model). The modelling results were compared with available 137 Cs air and ground contamination measurement data. The 137 Cs atmospheric transport over the territory of Ukraine was simulated during the first 12 days after the accident (from 26 April to 7 May 1986) using real aerological information and rain measurement network data. The detailed scenario of the release from the accidental unit of the Chernobyl nuclear plant has been built (including time-dependent radioactivity release intensity and time-varied height of the release). The calculations have enabled to explain the main features of spatial and temporal variations of radioactive contamination fields over the territory of Ukraine on the regional scale, including the formation of the major large-scale spots of radioactive contamination caused by dry and wet deposition

  2. Methodological guide: management of industrial sites potentially contaminated by radioactive substances

    International Nuclear Information System (INIS)

    2001-01-01

    At the request of the Ministries of Health and the Environment, IPSN is preparing and publishing the first version of the methodological guide devoted to managing industrial sites potentially contaminated by radioactive substances. This guide describes a procedure for defining and choosing strategies for rehabilitating such industrial sites. (author)

  3. The forming of the complexes of soil mezofauna in the zone of radioactive contamination

    International Nuclear Information System (INIS)

    Maksimova, S.L.

    2002-01-01

    We carried out the pedobiological research in the different biogeocenoses in the zone of radioactive contamination. Based on the obtained data we can conclude a direct correlation between the viability of the soil invertebrates and the background gamma-radiation intensity. All the facts indicate that soil animal complexes in biogeocenoses exposed to radiation for a long time impact clearly noticeable suppression

  4. Facilities for treatment of radioactive contaminated water in nuclear power plants

    International Nuclear Information System (INIS)

    1981-02-01

    The standard applies to processes applied in facilities for treatment of radioactive contaminated water in nuclear power plants with LWR- and HTR-type reactors. It does not apply to the treatment of concentrates obtained in the decontamination of water. (orig.) [de

  5. Radioautographic studies of the materials obtained from the No. 5 Fukuryu Maru contaminated by radioactive ashes

    Energy Technology Data Exchange (ETDEWEB)

    Kikuchi, T; Akagi, H; Goto, H; Wakisaka, G

    1954-01-01

    The contamination was associated with the presence of small radioactive particles. Although these particles were easily scattered, it was difficult to remove them completely. The particles did not penetrate into the interior of clothes of fine meshes. Decontamination by washing with sea water was not perfect.

  6. REAL-TIME IDENTIFICATION AND CHARACTERIZATION OF ASBESTOS AND CONCRETE MATERIALS WITH RADIOACTIVE CONTAMINATION

    International Nuclear Information System (INIS)

    XU, X. George; Zhang, X.C.

    2002-01-01

    Concrete and asbestos-containing materials were widely used in DOE building construction in the 1940s and 1950s. Over the years, many of these porous materials have been contaminated with radioactive sources, on and below the surface. To improve current practice in identifying hazardous materials and in characterizing radioactive contamination, an interdisciplinary team from Rensselaer has conducted research in two aspects: (1) to develop terahertz time-domain spectroscopy and imaging system that can be used to analyze environmental samples such as asbestos in the field, and (2) to develop algorithms for characterizing the radioactive contamination depth profiles in real-time in the field using gamma spectroscopy. The basic research focused on the following: (1) mechanism of generating of broadband pulsed radiation in terahertz region, (2) optimal free-space electro-optic sampling for asbestos, (3) absorption and transmission mechanisms of asbestos in THz region, (4) the role of asbestos sample conditions on the temporal and spectral distributions, (5) real-time identification and mapping of asbestos using THz imaging, (7) Monte Carlo modeling of distributed contamination from diffusion of radioactive materials into porous concrete and asbestos materials, (8) development of unfolding algorithms for gamma spectroscopy, and (9) portable and integrated spectroscopy systems for field testing in DOE. Final results of the project show that the combination of these innovative approaches has the potential to bring significant improvement in future risk reduction and cost/time saving in DOE's D and D activities

  7. Mathematical Modeling of Non-Fickian Diffusional Mass Exchange of Radioactive Contaminants in Geological Disposal Formations

    Directory of Open Access Journals (Sweden)

    Anna Suzuki

    2018-01-01

    Full Text Available Deep geological repositories for nuclear wastes consist of both engineered and natural geologic barriers to isolate the radioactive material from the human environment. Inappropriate repositories of nuclear waste would cause severe contamination to nearby aquifers. In this complex environment, mass transport of radioactive contaminants displays anomalous behaviors and often produces power-law tails in breakthrough curves due to spatial heterogeneities in fractured rocks, velocity dispersion, adsorption, and decay of contaminants, which requires more sophisticated models beyond the typical advection-dispersion equation. In this paper, accounting for the mass exchange between a fracture and a porous matrix of complex geometry, the universal equation of mass transport within a fracture is derived. This equation represents the generalization of the previously used models and accounts for anomalous mass exchange between a fracture and porous blocks through the introduction of the integral term of convolution type and fractional derivatives. This equation can be applied for the variety of processes taking place in the complex fractured porous medium, including the transport of radioactive elements. The Laplace transform method was used to obtain the solution of the fractional diffusion equation with a time-dependent source of radioactive contaminant.

  8. Derivation of uranium residual radioactive material guidelines for the Shpack site

    International Nuclear Information System (INIS)

    Cheng, J.J.; Yu, C.; Monette, F.; Jones, L.

    1991-08-01

    Residual radioactive material guidelines for uranium were derived for the Shpack site in Norton, Massachusetts. This site has been identified for remedial action under the Formerly Utilized Sites Remedial Action Program (FUSRAP) of the US Department of Energy (DOE). The uranium guidelines were derived on the basis of the requirement that the 50-year committed effective dose equivalent to a hypothetical individual who lives or works in the immediate vicinity of the Shpack site should not exceed a dose of 100 mrem/yr following decontamination. The DOE residual radioactive material guideline computer code, RESRAD, which implements the methodology described in the DOE manual for implementing residual radioactive material guidelines, was used in this evaluation. Three potential scenarios were considered for the site; the scenarios vary with regard to time spent at the site, sources of water used, and sources of food consumed. The results of the evaluation indicate that the basic dose limit of 100 mrem/yr will not be exceeded for uranium (including uranium-234, uranium-235, and uranium-238) within 1000 years, provided that the soil concentration of combined uranium (uranium-234 and uranium-238) at the Shpack site does not exceed the following levels: 2500 pCi/g for Scenario A (recreationist: the expected scenario); 1100 pCi/g for Scenario B (industrial worker: a plausible scenario); and 53 pCi/g for Scenario C (resident farmer using a well water as the only water source: a possible but unlikely scenario). The uranium guidelines derived in this report apply to the combined activity concentration of uranium-234 and uranium-238 and were calculated on the basis of a dose of 100 mrem/yr. In setting the actual uranium guidelines for the Shpack site, DOE will apply the as low as reasonably achievable (ALARA) policy to the decision-making process, along with other factors, such as whether a particular scenario is reasonable and appropriate. 8 refs., 2 figs., 8 tabs

  9. Characterization of freshwater mosses as indicators of radioactive contamination; Caracterisation de mousses dulcaquicoles comme indicateurs de contamination radioactive

    Energy Technology Data Exchange (ETDEWEB)

    Beaugelin-Seiller, K

    1994-12-16

    The necessity of indicators of freshwater contamination has developed the interest for aquatic mosses. From a fundamental point of view, studying the influence of some biotic and abiotic factors has permitted to better know the mechanisms of radionuclides accumulation by these bryophytes. From a radioecological point of view, simulating real cases of water contamination has allowed to give results a very interesting representativeness. The use of mosses as bio-indicators was applied for two in situ experiments, the results of which have been interpreted from those obtained in laboratory. Finally, an approach by a mathematical model has showed that it is possible to have, in a middle term, an evaluation tool of freshwater contamination, based on the radionuclides concentrations measured in aquatic mosses. (author). refs., 57 figs., 24 tabs.

  10. Geotechnical behavior of a tropical residual soil contaminated with gasoline

    Directory of Open Access Journals (Sweden)

    Óscar Echeverri-Ramírez

    2015-01-01

    Full Text Available La infraestructura para transporte de hidrocarburos ha crecido de manera importante debido a la necesidad de abastecer la mayo r cantidad de poblaciones; sin embargo por pro blemas en las redes de sumin istro, se presentan derrames accidentales que contaminan los su elos bajo los cuales se apoyan estas estructuras. Los suelos contaminados , en este caso particular con gasolina, son la motivación del p resente artículo, el cual pretende analizar los cambios que ocurren en un suelo d e origen residual tropical al ser contaminado con éste; mediant e pruebas de laboratorio específicos para caracterizar este tipo de suelos (Clasificación Miniatura Compactado Tropical, Succión, Pinhole Test, Índice de Colapso, Difracción de rayos “X”, Microscopía Electrónica de Barrido, determinación de pH y de ensayos tradicionales (hume dad natural, gravedad específica, granulometría, límites de Atterbe rg, corte directo, etc, tanto con muestras en estado natural c omo contaminadas que permitan percibir las posibles variaciones en las características mecánicas del material.

  11. Radioactivity of the Bega sediment-case study of a contaminated canal

    International Nuclear Information System (INIS)

    Bikit, I.; Varga, E.; Conkic, Lj.; Slivka, J.; Mrda, D.; Curcic, S.; Zikic-Todorovic, N.; Veskovic, M.

    2005-01-01

    The Bega canal is one among many heavily polluted canals in Vojvodina (the northern province of Serbia and Montenegro). In the framework of the revitalization of this canal, the radionuclide content of the sediment was investigated in order to support the safe deposition after excavation. It was found that, in comparison with the Danube sediment and Vojvodina soil, the Bega sediment is contaminated with 238 U and 137 Cs. The origin of this contamination is discussed. No traces of contamination by nuclear power plants in the region were found, while the presence of technologically enhanced, natural occurring radioactive materials (TENORM) was proved

  12. Device for contaminating laboratory animals by inhalation of radioactive aerosols

    International Nuclear Information System (INIS)

    Lutz, M.; Rouvroy, H.

    1966-01-01

    The contamination enclosure is made up of a sphere to which are attached an aerosol generator, containers adapted to the animals to be used, and the atmospheric sampling system. The sphere is placed in a protective glove-box, the latter being itself protected by an introduction chamber fitted with locking access lids. A detailed description is given of the working principle. As an example, some results are given concerning the contamination of rats by a plutonium oxide aerosol: characteristics of the powder (mean diameter 0.50 μ - standard deviation: 1.4), examination and evolution of the atmospheric activity as a function of time, evaluation of the retention by the lungs by means of histological and autoradiographic examinations. (authors) [fr

  13. Review of advanced methods for treating radioactive contaminated water

    International Nuclear Information System (INIS)

    Dubourg, M.

    2002-01-01

    The accidental release of large quantities of radionuclide after a nuclear accident tends to contaminate the groundwater system of rivers and lakes by the transfer of the main radionuclides such as Cesium 137, Strontium 90 or Cobalt 60, Ruthenium 106 and others (including transuranic radionuclides, such as: Pu 239, Pu 240, Am 241..). The aim of this paper is to review the possible solutions for the removal of these contaminants from large quantities of water. the use of crown ethers for the selective removal of strontium 90 such as the di-cyclohexyl 18 crown 6 which is able to remove with 90% of efficiency the strontium. the use of zeolites for the removal of Cesium 137. On larger scale the use of electromagnetic filtration technology is able to process in a relatively short time large quantities of water by using a seeding system of resin coated metallic magnetic particles to enhance the filtering efficiency under cold conditions. Examples of efficiencies and results obtained on loops at a fairly large will be given in this paper, theses examples show rather high efficiency of removal even at low concentration of contaminants (a few ppb: part per billion). Examples of water treatment concepts will be also given for treatment of contaminated surface water and to treat large groundwater applications. Major applications could be implemented on various sites namely in Russia (Karatchai lake) or in Belarus and Ukraine. The magnetic filtration is not a new concept but with the use of various selective adsorbing treatment particles, this concept has been proven so effective that dissolved metals in process water have been reduced to level in the very low ppb range. (authors)

  14. Environmental safety of the disposal system for radioactive substance-contaminated wastes

    International Nuclear Information System (INIS)

    Oosako, Masahiro

    2012-01-01

    In accordance with the full-scale enforcement of 'The Act on Special Measures concerning the Handling of Radioactive Pollution' in 2012, the collective efforts of entire Japan for dealing with radioactive pollutants began. The most important item for dealing with radioactive pollution is to control radioactive substances that polluted the global environment and establish a contaminated waste treatment system for risk reduction. On the incineration system and landfill disposal system of radioactive waste, this paper arranges the scientific information up to now, and discusses the safety of the treatment / disposal systems of contaminated waste. As for 'The Act on Special Measures concerning the Handling of Radioactive Pollution,' this paper discusses the points of the Act and basic policy, roadmap for the installation of interim storage facilities, and enforcement regulations (Ordinance of the Ministry of the Environment). About the safety of waste treatment system, it discusses the safety level of technical standards at waste treatment facilities, safety of incineration facilities, and safety of landfill disposal sites. (O.A.)

  15. Treatment of Radioactive Contaminated Soil and Concrete Wastes Using the Regulatory Clearance

    Energy Technology Data Exchange (ETDEWEB)

    Kang, Il Sik; Ryu, W. S.; Kim, T. K.; Shon, J. S.; Ahn, S. J.; Lee, Y. H.; Bae, S. M.; Hong, D. S.; Ji, Y. Y.; Lee, B. C

    2008-11-15

    In the radioactive waste storage facilities at the Korea Atomic Energy Research Institute (KAERI) in Daejoen, there are thousands drums of radioactive contaminated soil and concrete wastes. The soil and concrete wastes were generated in 1988 during the decommissioning process of the research reactor and the attached radioactive waste treatment facility which were located in Seoul. The wastes were transported to Daejeon and have been stored since then. At the generation time, the radioactive contamination of the wastes was very low, and the radionuclides in the wastes was Co-60 and Cs-137. As the wastes have been stored for more than 20 years, the radioactivity concentration of the wastes has been decayed to become very extremely low. The wastes are needed to be treated because they take up large spaces at the storage facility. Also by treating the wastes, final disposal cost can be saved. So, the regulatory clearance was considered as a treatment method for the soil and concrete wastes with extremely low radioactivity concentration.

  16. Blast furnace residues for arsenic removal from mining-contaminated groundwater.

    Science.gov (United States)

    Carrillo-Pedroza, Fco Raúl; Soria-Aguilar, Ma de Jesús; Martínez-Luevanos, Antonia; Narvaez-García, Víctor

    2014-01-01

    In this work, blast furnace (BF) residues were well characterized and then evaluated as an adsorbent material for arsenic removal from a mining-contaminated groundwater. The adsorption process was analysed using the theories of Freundlich and Langmuir. BF residues were found to be an effective sorbent for As (V) ions. The modelling of adsorption isotherms by empirical models shows that arsenate adsorption is fitted by the Langmuir model, suggesting a monolayer adsorption of arsenic onto adsorbents. Arsenate adsorption onto BF residue is explained by the charge density surface affinity and by the formation of Fe (II) and Fe (III) corrosion products onto BF residue particles. The results indicate that BF residues represent an attractive low-cost absorbent option for the removal of arsenic in wastewater treatment.

  17. The Russian Northern Fleet. Sources of radioactive contamination

    Energy Technology Data Exchange (ETDEWEB)

    Nilsen, T [Bellona Foundation, Oslo (Norway); Kudrik, I [Bellona Foundation Branch Office, Murmansk (Russian Federation); Nikitin, A [Scientific Production Association ` ` Typhoon` ` , Obninsk (Russian Federation)

    1996-08-01

    The report describes the problems that the Russian Northern Fleet is experiencing with its nuclear powered vessels and with the storage of spent fuel and other nuclear wastes that the operation of these vessels generates. One of the most serious problems is the lack of regional storage and treatment facilities for radioactive waste. This waste is now deposited haphazardly throughout the various navy yards and bases. The establishment of a regional storage facility for spent fuel, radioactive reactor components, and liquid and solid nuclear waste is a necessary precondition for carrying out the decommissioning of nuclear submarines in an environmentally viable manner. A recurrent theme in the report is the lack of civilian control over the different Northern Fleet nuclear facilities. This leads to a disregard of international recommendations with regard to the handling of nuclear waste. Considerable effort has been made to provide comprehensive references in the report, making it clear that the authors sources of information have been open. By presenting this information the authors hope to contribute to increased insight and consequently to help realize necessary national and international measures. 93 refs.

  18. The Russian Northern Fleet. Sources of radioactive contamination

    International Nuclear Information System (INIS)

    Nilsen, T.; Kudrik, I.; Nikitin, A.

    1996-08-01

    The report describes the problems that the Russian Northern Fleet is experiencing with its nuclear powered vessels and with the storage of spent fuel and other nuclear wastes that the operation of these vessels generates. One of the most serious problems is the lack of regional storage and treatment facilities for radioactive waste. This waste is now deposited haphazardly throughout the various navy yards and bases. The establishment of a regional storage facility for spent fuel, radioactive reactor components, and liquid and solid nuclear waste is a necessary precondition for carrying out the decommissioning of nuclear submarines in an environmentally viable manner. A recurrent theme in the report is the lack of civilian control over the different Northern Fleet nuclear facilities. This leads to a disregard of international recommendations with regard to the handling of nuclear waste. Considerable effort has been made to provide comprehensive references in the report, making it clear that the authors sources of information have been open. By presenting this information the authors hope to contribute to increased insight and consequently to help realize necessary national and international measures. 93 refs

  19. Radioactive contamination of food in Slovenia after Chernobyl incident

    Energy Technology Data Exchange (ETDEWEB)

    Milohnoja, M [Veterinary College, Ljubljana (Yugoslavia)

    1986-07-01

    This review of the situation and of measures on veterinary inspection is confined to Slovenia (the most northern republic of SFR Yugoslavia). First analysis of grass and rain-water made on 30 April 1986 showed that Slovenian agricultural superficies are contaminated with J-131 and Cs-137. A program of monitoring grass, rain-water, milk, meat of slaughter animals and game, fish, eggs and other food (vegetables) was made. The degree of contamination of milk with J-131 was very high in the first 10 days of month May, then rapidly lowered. All dairy cattle kept indoors, fed with old feeding stuff and watered with drinking water had milk with less than 60 Bq/l J-131. After 10 May the degree of contamination of milk with Cs-137 and Cs-134 began slowly to increase, but in June to decrease, so that most of the examined samples had less than 100 Bq/l Cs-137 and Cs-134. All milk (from the areas) with more than 200 Bq/l J-131 was sent to milk powder factory or to cheese-dairies. Analyses (made in July and August) of this milk powder showed that J-131 has almost 'disappeared', the content of Cs-137 and Cs-134 varied from 504 to 1150 Bq/l (i.e. 63 to 144 Bq/l in reconstituted milk); in cheese the content of Cs-137 and Cs-134 was lower than 100 Bq/kg.

  20. Radioactive contamination of food in Slovenia after Chernobyl incident

    International Nuclear Information System (INIS)

    Milohnoja, M.

    1986-01-01

    This review of the situation and of measures on veterinary inspection is confined to Slovenia (the most northern republic of SFR Yugoslavia). First analysis of grass and rain-water made on 30 April 1986 showed that Slovenian agricultural superficies are contaminated with J-131 and Cs-137. A program of monitoring grass, rain-water, milk, meat of slaughter animals and game, fish, eggs and other food (vegetables) was made. The degree of contamination of milk with J-131 was very high in the first 10 days of month May, then rapidly lowered. All dairy cattle kept indoors, fed with old feeding stuff and watered with drinking water had milk with less than 60 Bq/l J-131. After 10 May the degree of contamination of milk with Cs-137 and Cs-134 began slowly to increase, but in June to decrease, so that most of the examined samples had less than 100 Bq/l Cs-137 and Cs-134. All milk (from the areas) with more than 200 Bq/l J-131 was sent to milk powder factory or to cheese-dairies. Analyses (made in July and August) of this milk powder showed that J-131 has almost 'disappeared', the content of Cs-137 and Cs-134 varied from 504 to 1150 Bq/l (i.e. 63 to 144 Bq/l in reconstituted milk); in cheese the content of Cs-137 and Cs-134 was lower than 100 Bq/kg

  1. Review of the incineration of 500 tonnes of radio-active residues

    International Nuclear Information System (INIS)

    Rodier, J.; Seyfried, P.; Charbonneaux, M.

    1969-01-01

    During its first five years operation, the incinerator at the Marcoule Centre has burnt almost 500 tonnes of radio-active residues. Improvements in some of the details of the process have been made during this period; they concern the nature of the materials involved. The technical and radiological results for the installation are very favorable, and have made it possible to maintain a high charge factor.Although the overall economic results are not advantageous in the case of ungraded solid residues this method represents nevertheless the best available for eliminating oils, solvents, wood and dead animals. It can also be of use furthermore each time that a dilution in the atmosphere can advantageously be used as a method of disposing of certain radio elements such as tritium or carbon 14 in the form of gases or vapours. (author) [fr

  2. Long-term management of the existing radioactive wastes and residues at the Niagara Falls Storage Site. Draft Environmental Impact Statement

    International Nuclear Information System (INIS)

    1984-08-01

    The statement assesses and compares several alternatives for long-term management of the existing radioactive wastes and residues at the Niagara Falls Storage Site (NFSS), Lewiston, New York. The alternatives include: (1) no action (continued interim storage at NFSS within a diked and capped containment area), (2) long-term management at NFSS (improved containment, with or without modified form of the residues), (3) long-term management at other DOE sites (Hanford, Washington, or Oak Ridge, Tennessee), and (4) offsite management of the residues at Hanford or Oak Ridge and either leaving the wastes at NFSS or removing them for disposal in the ocean. In addition to alternatives analyzed in depth, several options are also considered, including: other modifications of residue form, modification of the basic conceptual designs, other containment design options, transportation routes, and transportation modes. The radiological health effects (primarily increased risk of cancer) associated with long-term management of the wastes and residues are expected to be smaller than the nonradiological risks of occupational and transportation-related injuries and deaths. During the action period, the risk is highest for workers if all wastes and residues are moved to Hanford. The risk is highest for the general public if the residues are moved to Hanford and the wastes are moved to the ocean. Dispersal of the slightly contaminated wastes in the ocean is not expected to result in any significant impacts on the ocean environment or pose any significant radiological risk to humans. For all alternatives, if controls ceased, there would be eventual dispersion of the radioactive materials to the environment. If it is assumed that all controls cease, predicted time for loss of covers over the buried materials ranges from several hundred years to more than two million years, depending on the use of the land surface

  3. Radioactive contamination of protective clothes made of textile and their decontamination in aqueous solutions

    International Nuclear Information System (INIS)

    Fukumori, D.T.

    1989-01-01

    This dissertation deals with the radioactive contamination, its prevention, control and decontamination, related to protective clothing made of textile and usually weared in normal working conditions, within the installations where radioactive materials are handled or processed, especially as unsealed sources. The features of textile materials and contaminants, contamination mechanisms, risks related to contaminated clothes, planning of working areas, monitoring and surface contamination limits are described. Concerning to decontamination, the reagents, their action mechanisms and methods of efficiency evaluation are emphasized. The selected reagents were experimentally tested and their efficiencies in decontaminating cotton cloth samples, contaminated with uranyl nitrate solution, were evaluated by means of counting rate determined with a Geiger-Muller provided counting system. In this way, complexing agents, surfactants and commercial cleanning products were tested. The results were analysed and interpreted considering statistical, radiochemical and Radiation Protection aspects. Both, the radiactive contamination and decontamination of protective clothes are extensive matters and they still could be developed and improved; thus, many suggestions were presented as further studies. (author) [pt

  4. The changes in the ecology and physiology of soil invertebrates under influences of radioactive contamination

    International Nuclear Information System (INIS)

    Maksimova, S.

    2006-01-01

    The soil biota is important in building and maintaining soil structure and fertility. Invertebrates are ideal as potential bio indicators of the environmental impact of radioactive contamination: they are widely distributed, often abundant and generally thought of as having low dispersive capacity. They can use as test organisms to detect the side-effects of radioactive contamination. The long-term analysis of ecological and physiological after-effects and biodiversity changes had been studied in the zone of radioactive contamination. Material was collected in the Gomel Region (Belarus), 30 km away from the CNPP in 1986-2004 applying usual pedobiological techniques (soil samples and Barber's pitfall traps) at reference points subjected to radioactive contamination. Soil samples were collected at 0 to 25 cm depth. Samples were taken in locations, which had received considerable radionuclide contaminations. These sites differed in contamination by the composition of fall-out, the forms of radionuclide content in soils, their intake into trophic chains and accumulation in animal and plant organisms. The impacts have been investigated at the: 1) organism and population levels , in terms of individual life histories (birth rate, growth, mortality) or species selection; 2) at the community level: to species diversity and to effects on trophic structure. The invertebrates were determined to species or genera, including juvenile stages. Radioactive contamination caused a distinct decrease in species number; the dominance structure of the community changed. The saprophagous are especially sensitive to environmental disturbances. An initial sharp reduction of animal biodiversity and simplification of the community structure of soil fauna were observed, followed by a long-term process of returning to the initial parameters. Changes in hemolymph, necroses of epithelium and cell structure in connective tissue were registered. The most drastic after-effects were manifested in

  5. Dispersal of radioactivity by wildlife from contaminated sites in a forested landscape

    International Nuclear Information System (INIS)

    Garten, C.T. Jr.

    1992-01-01

    Oak Ridge National Laboratory (ORNL) is located within the Ridge and Valley physiographic province of eastern Tennessee (USA). This area is characterized by deciduous forests dominated by hardwood and mixed mesophytic tree species. Wildlife populations have access to some radioactively contaminated sites at ORNL, and contaminated animals or animal nests within the Laboratory's boundaries have been found to contain on the order of 10 -12 to 10 -6 Ci/g of 90 Sr or 137 Cs, and trace amounts of other radionuclides (including transuranic elements). Theoretical calculations indicate that nanocurie levels of 90 Sr in bone can arise from relatively small amounts (1%) of contaminated browse vegetation in a deer's diet. Measures that have been undertaken at ORNL to curtail the dispersal of radioactivity by animals are briefly reviewed

  6. Study of the correlation between radioactive contamination of milk and forage with strontium 90

    Energy Technology Data Exchange (ETDEWEB)

    Sabo, A; Mezei, I [Joint Inst. for Nuclear Research, Dubna (USSR). Lab. of Neutron Physics

    1978-08-01

    Significant correlation between radioactive contamination of milk and forage is established on the basis of the data mathematic treatment. Contamination of cow milk by /sup 90/Sr is approximately one order less than forage contamination, which testifies to high discrimination ability of cows in biological chain soil-plant-animal-man. Animals have this ability only in relation to /sup 90/Sr. For other radioactive isotopes discirmination factor can differ significantly from the one characteristic of /sup 90/Sr. It is stressed that as a result of high discrimination ability of cows /sup 90/Sr quantity, penetrating into human body from vegetable products is much more, than the one penetrating from milk and milk products.

  7. Model of external exposure of population living in the areas subjected to radioactive contamination

    International Nuclear Information System (INIS)

    Golikov, V.Yu.; Balonov, M.I.

    2002-01-01

    In the paper, we formulated the general approach to assessment of external doses to population living in contaminated areas (the model equation and the set of parameters). The model parameters were assessed on the basis of results of monitoring in the environment, phantom experiments, and social and demographic information obtained on the contaminated areas. Verification of model assessments performed by comparison with measurement results of individual external doses in inhabitants within the thermoluminescent dosimetry method have shown that differences in dose assessments within both methods does not exceed 1.5 times at a confidence level of 95%. In the paper, we present the results illustrating specific features of external dose formation in population living in the areas of Russia subjected to radioactive contamination due to nuclear tests at the Semipalatinsk test site, radioactive releases from the Mayak enterprise, and the Chernobyl accident. (author)

  8. The consequences of radioactive contamination of forest ecosystems due to Chernobyl accident

    International Nuclear Information System (INIS)

    Tikhomirov, F.A.; Shcheglova, A.I.

    1997-01-01

    The effect of forests on the radionuclide primary distribution in different components of the contaminated ecosystems is considered by the example of Chernobyl accident. A basic mathematical model is developed describing 137 Cs biogeochemical cycling under conditions of quasi-steady state radionuclide redistribution in the ecosystem. Forest ecosystems are proved to diminish radionuclide migration in the environment, and forest should be regarded as an important sanitary factor. The contribution of contaminated forests and forest products to the total irradiation dose to local population is estimated. Special countermeasures are elaborated in order to diminish unfavorable consequences of forest radioactive contamination. A long-term dynamics of radioactive situation in the forest ecosystems in forecasted and further studies on the subject are drafted

  9. Some thoughts concerning the radioactive contamination of foodstuffs 10 years after the Chernobyl disaster

    International Nuclear Information System (INIS)

    Szabo, S.A.

    1997-01-01

    Although the Chernobyl disaster happened 10 years ago (26 Apr. 1986), investigation of the radioactive contamination of the environmental is still in the focus of interest. However it can be established that the pollution level in Hungary- like other, from the place of accident rather far located countries - decreased significantly in the food chain in comparison with measured data in May-June, 1986. Practically the present contamination level (e.q. 137 Cs, 90 Sr) since 1989 is the same as it was in the years before the disaster. Since the level of artificial contamination is much less than the natural radioactivity (e.q. 40 K, 226 Ra) of the foodstuffs, the radiation burden caused by the consumed foodstuffs is negligible. (author)

  10. Building classification trees to explain the radioactive contamination levels of the plants; Construction d'arbres de discrimination pour expliquer les niveaux de contamination radioactive des vegetaux

    Energy Technology Data Exchange (ETDEWEB)

    Briand, B

    2008-04-15

    The objective of this thesis is the development of a method allowing the identification of factors leading to various radioactive contamination levels of the plants. The methodology suggested is based on the use of a radioecological transfer model of the radionuclides through the environment (A.S.T.R.A.L. computer code) and a classification-tree method. Particularly, to avoid the instability problems of classification trees and to preserve the tree structure, a node level stabilizing technique is used. Empirical comparisons are carried out between classification trees built by this method (called R.E.N. method) and those obtained by the C.A.R.T. method. A similarity measure is defined to compare the structure of two classification trees. This measure is used to study the stabilizing performance of the R.E.N. method. The methodology suggested is applied to a simplified contamination scenario. By the results obtained, we can identify the main variables responsible of the various radioactive contamination levels of four leafy-vegetables (lettuce, cabbage, spinach and leek). Some extracted rules from these classification trees can be usable in a post-accidental context. (author)

  11. Evolution of radioactive dose rates in fresh sediment deposits along coastal rivers draining Fukushima contamination plume.

    Science.gov (United States)

    Evrard, Olivier; Chartin, Caroline; Onda, Yuichi; Patin, Jeremy; Lepage, Hugo; Lefèvre, Irène; Ayrault, Sophie; Ottlé, Catherine; Bonté, Philippe

    2013-10-29

    Measurement of radioactive dose rates in fine sediment that has recently deposited on channel bed-sand provides a solution to address the lack of continuous river monitoring in Fukushima Prefecture after Fukushima Dai-ichi nuclear power plant (FDNPP) accident. We show that coastal rivers of Eastern Fukushima Prefecture were rapidly supplied with sediment contaminated by radionuclides originating from inland mountain ranges, and that this contaminated material was partly exported by typhoons to the coastal plains as soon as by November 2011. This export was amplified during snowmelt and typhoons in 2012. In 2013, contamination levels measured in sediment found in the upper parts of the catchments were almost systematically lower than the ones measured in nearby soils, whereas their contamination was higher in the coastal plains. We thereby suggest that storage of contaminated sediment in reservoirs and in coastal sections of the river channels now represents the most crucial issue.

  12. Radioactive contaminants in raw materials and foodstuffs of plant origin

    International Nuclear Information System (INIS)

    Stankovicj, S.; Krainchanicj, M.; Stankovicj, A.

    1990-01-01

    The paper concentrates on the results of activity level of radioactive caesium 134 and 137 in the samples of raw materials (barley, oats, soybean, sunflower, pumpkin seed, hops, shreded sugar beet, maize), animal feedstuffs (alfalfa, alfalfa meal, rape, concentrates fed to chickens, pigs or bpvines, dry turnip shreds) and foodstuff of plant origin (lettuce, spinach, cabbage, carrot, celery, cucumber, tomato, olives, sesame). All samples - produced locally on the major part but also including some imported stuff -have been subjected to continuous gamma spectrometry starting with the Chernobyl accident in 1986 through 1989. The highest activity of caesium was recorded in the samples of animal feedstuffs (alfalfa, alfalfa meal, rape) in the years 1986 and 1987. In time, however, the activity tends to drop considerably. (author) 4 refs.; 3 tabs

  13. Analysis of disposition alternatives for radioactively contaminated scrap metal

    International Nuclear Information System (INIS)

    Nieves, L.A.; Chen, S.Y.; Kohout, E.J.; Nabelssi, B.; Tilbrook, R.W.; Wilson, S.E.

    1997-01-01

    Millions of tonnes of slightly radioactive, scrap iron and steel, stainless steel, and copper are likely to become available as nuclear and other facilities and equipment are withdrawn from service. Disposition of this material is an international policy issue under consideration currently. The major alternatives for managing this material are to either develop a regulatory process for decontamination and recycling that will safeguard human health or to dispose of the scrap and replace the metal stocks. To evaluate the alternatives, we estimate quantities of scrap arising from nuclear power plant decommissioning, evaluate potential price impacts of recycling on regional markets, and assess the health and environmental impacts of the management alternatives. We conclude that decontaminating and recycling the scrap is the superior alternative

  14. Shielding design of radioactive contaminated metal waste packaging

    International Nuclear Information System (INIS)

    Zou Wenhua; Dong Zhiqiang; Yao Zhenyu; Xu Shuhe; Wang Wen

    2015-01-01

    Focusing on the cylindrical source model to calculate γ dose field of waste packages with the relative formulae then derived. By comparing the calculated data of waste packages of type Ⅷ steel box with the monitoring data, it is found that the cylinder source model could accurately reflect the distributions of γ dose of the waste package. Based on the results of the cylindrical source model, a reasonable shielding technology applicable to waste package containers was designed to meet relevant requirements prescribed in standards about the transport and disposal of radioactive materials. The cylinder source model calculated dose distributions for single package in this paper is simple and easy to implement but slightly larger than the monitoring data providing a certain safety margin for the shielding design. It is suitable for radiological engineering practices. (authors)

  15. Dealing with presumed radioactive contamination - a modest proposal

    International Nuclear Information System (INIS)

    Austerlitz, C.; Campos, D.; Villar, H.P.

    2009-01-01

    Reports concerning the occurrence of malignancies and cancer cases among the population caused by the presence of radioactive materials in the environment are not unusual in Brazil. The country's Nuclear Energy Commission, CNEN, is always assigned to launch an investigation in such cases. As a result, human and financial resources are usually committed in operations that, more often than not, end up by discovering that claims are riot related to radiation. This time it was based on some uranium prospecting that has been made near a small town, Lajes Pintadas, RN. Alarmist reports concerning occurrence of stillborn and malformed children and of cancer cases among the adult population, reached the state capital. A team from CNEN was dispatched to Lajes Pintadas to look for the effective presence of environmental radionuclides and to investigate the reported occurrence of malignancies caused by radiation. Due to the well-known dangers related to launching an investigation on a subject so controversial and prone to misinterpretation by the media and the public, a novel approach, both in technical and philosophical terms, was attempted and that proved to be crucial for the success of the whole undertaking: eight years on, no more reports on health problems in Lajes Pintadas were publicised. It was concluded that standard procedures towards claims concerning health problems related to the presence of radioactive materials in the environment need to be re-evaluated. A more realistic approach towards nuclear activities and their risks should be established and the guidelines proposed herein (thorough survey of available data, involvement of local officials and of the affected community, and careful handling of the media) should be closely followed. (author)

  16. Levels and trends of radioactive contaminants in the Greenland environment

    DEFF Research Database (Denmark)

    Dahlgaard, H.; Eriksson, M.; Nielsen, S.P.

    2004-01-01

    . The concentrations are expected to increase in the future, especially in East Greenland. The Bylot Sound at the Thule Airbase (Pituffik) in North-West Greenland was contaminated with plutonium and enriched uranium in a weapons accident in 1968. Biological activity has mixed accident plutonium efficiently...... into the new sediments resulting in continued high surface sediment concentrations three decades after the accident. Transfer of plutonium to benthic biota is low-and lower than observed in the Irish Sea. This is supposed to be caused by the physico-chemical form of the accident plutonium. A recent study...

  17. Phytoremediation of radioactive contaminated soil research and feasibility

    International Nuclear Information System (INIS)

    Li Jianguo; Han Baohua; Ma Binghui; Wang Huijuan; Liang Yong; Liu Jie

    2014-01-01

    Phytoremediation is an emerging environmental control technology with economic, environmental friendliness, etc., but also constrained by a variety of factors, such as difficulties of Hyperaccumulator screening, poor adaptability of plants, longer growing season and low biomass, which greatly limited the development and application of phytoremediation technology. This paper decribed the principles of phytoremediation for U, Sr and Cs contaminated soil, introduced research status involved, briefly nanlyzed the feasibility of phytoremediation techniques combined with the nuclear environmental remediation standards, and proposed suggestions for further researches. (authors)

  18. Zinc species distribution in EDTA-extract residues of zinc-contaminated soil

    International Nuclear Information System (INIS)

    Chang, S.-H.; Wei, Y.-L.; Wang, H. Paul

    2007-01-01

    Soil sample from a site heavily contaminated with >10 wt.% zinc is sampled and extracted with aqueous solutions of ethylene diamine tetra-acetic acid (EDTA) that is a reagent frequently used to extract heavy metals in soil remediation. Three liquid/soil ratios (5/1, 20/1, and 100/1) were used in the extracting experiment. The molecular environment of the residual Zn in the EDTA-extract residues of zinc-contaminated soil is investigated with XANES technique. The results indicate that EDTA does not show considerable preference of chelating for any particular Zn species during the extraction. Zn species distribution in the sampled soil is found to resemble that in all EDTA-extract residues; Zn(OH) 2 is determined as the major zinc species (60-70%), seconded by organic zinc (21-26%) and zinc oxide (9-14%)

  19. Distribution of radioactive Cesium in trees and effect of decontamination of forest contaminated by the Fukushima nuclear accident

    International Nuclear Information System (INIS)

    Iijima, K.; Funaki, H.; Tokizawa, T.; Nakayama, S.

    2013-01-01

    In decontamination pilot projects conducted by Japan Atomic Energy Agency (JAEA), many different techniques were tested to determine their applicability to remediate areas evacuated after the Fukushima Daiichi nuclear accident following the Great Tohoku earthquake and tsunami of March 11, 2011. In addition to buildings, roads and farmland, the forest adjacent to living areas was one of the main decontamination targets. The projects evaluated the radioactive contamination of trees and the effectiveness of decontaminating a highly contaminated evergreen forest. This forest was located 1.3 km southwest of the Fukushima Daiichi Nuclear Power Plant and is dominated by Japanese cedar trees and fir trees. As the first step, three Japanese cedar trees and three fir trees were cut down and the distributions of radioactive cesium (Cs) were measured in each. The total concentrations of 134 Cs and 137 Cs in the leaves and branches were about 1 MBq/kg for both cedar and fir trees, and were appreciably higher than in the bark for cedar. The concentrations in the outer part of the trunks (under the bark) were lower, on the order of 10 kBq/kg, and those in the core of the trunks were lower than 1 kBq/kg for both kinds of trees. The observation that the Cs concentrations are higher in the outer part of trees, is compatible with the assumption that radio-Cs was mostly adsorbed on the surface of trees and partly penetrated into the trunks through the bark. Evolution of air dose rates in a 100 x 60 m pasture adjacent to the forest was monitored during decontamination of the forest and of the pasture itself. The dose rates in the pasture decreased drastically after stripping contaminated topsoil from the pasture and decreased slightly more after stripping contaminated topsoil of the forest floor and pruning the trees. Cutting down and removing 84 trees in the outermost area (10- m width) of the forest also slightly decreased these dose rates. After decontamination, the residual dose

  20. Emerging Environmental Justice Issues in Nuclear Power and Radioactive Contamination

    Directory of Open Access Journals (Sweden)

    Dean Kyne

    2016-07-01

    Full Text Available Nuclear hazards, linked to both U.S. weapons programs and civilian nuclear power, pose substantial environment justice issues. Nuclear power plant (NPP reactors produce low-level ionizing radiation, high level nuclear waste, and are subject to catastrophic contamination events. Justice concerns include plant locations and the large potentially exposed populations, as well as issues in siting, nuclear safety, and barriers to public participation. Other justice issues relate to extensive contamination in the U.S. nuclear weapons complex, and the mining and processing industries that have supported it. To approach the topic, first we discuss distributional justice issues of NPP sites in the U.S. and related procedural injustices in siting, operation, and emergency preparedness. Then we discuss justice concerns involving the U.S. nuclear weapons complex and the ways that uranium mining, processing, and weapons development have affected those living downwind, including a substantial American Indian population. Next we examine the problem of high-level nuclear waste and the risk implications of the lack of secure long-term storage. The handling and deposition of toxic nuclear wastes pose new transgenerational justice issues of unprecedented duration, in comparison to any other industry. Finally, we discuss the persistent risks of nuclear technologies and renewable energy alternatives.

  1. Emerging Environmental Justice Issues in Nuclear Power and Radioactive Contamination.

    Science.gov (United States)

    Kyne, Dean; Bolin, Bob

    2016-07-12

    Nuclear hazards, linked to both U.S. weapons programs and civilian nuclear power, pose substantial environment justice issues. Nuclear power plant (NPP) reactors produce low-level ionizing radiation, high level nuclear waste, and are subject to catastrophic contamination events. Justice concerns include plant locations and the large potentially exposed populations, as well as issues in siting, nuclear safety, and barriers to public participation. Other justice issues relate to extensive contamination in the U.S. nuclear weapons complex, and the mining and processing industries that have supported it. To approach the topic, first we discuss distributional justice issues of NPP sites in the U.S. and related procedural injustices in siting, operation, and emergency preparedness. Then we discuss justice concerns involving the U.S. nuclear weapons complex and the ways that uranium mining, processing, and weapons development have affected those living downwind, including a substantial American Indian population. Next we examine the problem of high-level nuclear waste and the risk implications of the lack of secure long-term storage. The handling and deposition of toxic nuclear wastes pose new transgenerational justice issues of unprecedented duration, in comparison to any other industry. Finally, we discuss the persistent risks of nuclear technologies and renewable energy alternatives.

  2. Radioactive Mapping Contaminant of Alpha on The Air in Space of Repair of Hot Cell and Medium Radioactivity Laboratory in Radio metallurgy Installation

    International Nuclear Information System (INIS)

    Yusuf-Nampira; Endang-Sukesi; S-Wahyuningsih; R-Budi-Santoso

    2007-01-01

    Hot cell and space of acid laboratory medium activity in Radio metallurgy Installation are used for the examination preparation of fuel nuclear post irradiation. The sample examined is dangerous radioactive material representing which can disseminate passing air stream. The dangerous material spreading can be pursued by arranging air stream from laboratory space to examination space. To know the performance the air stream arrangement is hence conducted by radioactive mapping contaminant of alpha in laboratory / space of activity place, for example, medium activity laboratory and repair space. This mapping radioactivity contaminant is executed with the measurement level of the radioactivity from sample air taken at various height with the distance of 1 m, various distance and from potential source as contaminant spreading access. The mapping result indicate that a little spreading of radioactive material happened from acid cupboard locker to laboratory activity up to distance of 3 m from acid cupboard locker and spreading of radioactive contaminant from goods access door of the hot cell 104 to repair space reach the distance of 2 m from goods door access. Level of the radioactive contamination in the space was far under maximum limitation allowed (20 Bq / m 3 ). (author)

  3. Recommendations for sampling for prevention of hazards in civil defense. On analytics of chemical, biological and radioactive contaminations. Brief instruction for the CBRN (chemical, biological, radioactive, nuclear) sampling

    International Nuclear Information System (INIS)

    Bachmann, Udo; Biederbick, Walter; Derakshani, Nahid

    2010-01-01

    The recommendation for sampling for prevention of hazards in civil defense is describing the analytics of chemical, biological and radioactive contaminations and includes detail information on the sampling, protocol preparation and documentation procedures. The volume includes a separate brief instruction for the CBRN (chemical, biological, radioactive, nuclear) sampling.

  4. Methods for studying the radioactive contamination of plants (1963); Methodes d'etude de la contamination radioactive des vegetaux (1963)

    Energy Technology Data Exchange (ETDEWEB)

    Coulon, R; Jeanmaire, L; Michon, G [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

    1963-07-01

    The authors first define the doctrine which led to the devising of a method for studying the radioactive pollution of plants, based on the use of simple techniques, having the possibility of being adapted for routine work, and so devised that each stage is proceeded with only if the preceding one justifies it. For each stage a study is effected comparing the results obtained by the use of more exact techniques. The second part describes in detail the techniques used. (authors) [French] Dans une premiere partie lea auteurs definissent la doctrine qui leur a permis d'elaborer une methode d'etude de la pollution radioactive des vegetaux, basee sur l'utilisation de techniques simples, se pretant au travail de serie et concues de telle maniere que chaque etape n'est abordee que si la precedente le justifie. Chaque etape fait l'objet d'une etude qui compare les resultats a ceux obtenue par des techniques plus precises. La deuxieme partie decrit dans le detail les techniques utilisees. (auteurs)

  5. Comparison between ex situ and in situ measurement methods for the assessment of radioactively contaminated land. Comparison between measurement methods for the characterisation of radioactively contaminated land

    International Nuclear Information System (INIS)

    Rostron, Peter D.; Ramsey, Michael H.; Heathcote, John A.

    2012-01-01

    In the UK, it is estimated that there may be 20,000,000 cubic metres of contaminated land at Sellafield alone. Harwell and Dounreay are known to have significant amounts of radioactive or nonradioactive contaminated land (NDA, 2006). It is therefore important to devise optimal methods for the characterisation of areas of land for radionuclide content, in order to enable cost-effective decommissioning. With chemical contaminants, ex situ measurements are made on a larger volume of soil than are in situ measurements, such as PXRF. However, the opposite is often true for the characterisation of radioactive contamination, when this involves the detection of penetrating radiation from γ-emitting radionuclides. This means that when investigating for hotspots of radioactive contamination at or near the ground surface, better coverage can be obtained using in situ methods. This leads to the question, what is the optimal strategy (e.g. percentage coverage, counting time) for in situ characterisation of radioactively contaminated land' Surveys on light-moderate contaminated areas of ground were conducted at Dounreay in order to compare the relative effectiveness of in situ and ex situ methods, both for the detection of radioactive hotspots and also for estimating the average radionuclide content of an area of ground. These surveys suggest that continuous coverage by in situ devices is more effective at hotspot detection, with ex situ laboratory measurements being less effective, although in one case elevated activity below 10 cm depth that was identified by ex situ measurement was not located by in situ measurement. The surveys also highlighted that careful choice of an appropriate spatial model is critical to the estimation of activity concentrations over averaging areas. Whereas continuous coverage may be considered necessary for hotspot identification, in the particular case of the detection of hot particles (where the particle is very small compared to the sampling

  6. Derivation of cesium-137 residual radioactive material guidelines for the Peek Street site, Schenectady, New York

    International Nuclear Information System (INIS)

    Jones, L.; Nimmagadda, M.; Yu, C.

    1992-01-01

    Residual radioactive material guidelines for cesium-137 were derived for the Peek rk. The derivation was based on the requirement that the Street site in Schenectady, New York. The derivation was based on the requirement that the 50-year committed effective dose equivalent to a hypothetical individual who lives or works in the immediate vicinity of the Peek Street site should not exceed a dose of 100 mrem/yr following remedial action. The US Department of Energy (DOE) residual radioactive material guideline computer code, RESRAD was used in this evaluation. Three potential scenarios were considered for the site on the assumption that for a period of 1,000 years following remedial action, the site wig be utilized without radiological restrictions. The scenarios vary with regard to use of the site, time spent at the site, and sources of food consumed. Results indicate that the basic dose limit of 100 mrem/yr will not be exceeded for cesium-137 within 1,000 years, provided that the soil concentration of cesium-137 at the Peek Street site does not exceed the following levels: 98 pCi/g for Scenario A (industrial worker: the expected scenario), 240 pCi/g for Scenario B (recreationist: a plausible scenario), and 34 pCi/g for Scenario C (resident farmer ingesting food produced in the decontaminated area: a plausible scenario)

  7. General radioactive contamination of the biosphere measurements in the Netherlands 1974. Annual report Coordination Commission radioactivity measurements and Coordination Commission for the measurements of radioactivity and xenobiotic materials

    Energy Technology Data Exchange (ETDEWEB)

    1975-07-01

    For several years, measurements have been performed in the Netherlands to determine radioactive contamination of the biosphere. These measurements are carried out by various institutes responsible to three ministries: the Ministery of 'Health and Environmental Protection', of 'Agriculture and Fisheries' and of 'Transport and Water', (Dutch: 'Verkeer en Waterstaat', under the supervision of the Coordination Commission Radioactive Measurements (CCRA)). Besides radionuclides, many other elements and compounds are considered harmful for man, animal and the environment. A systematic control of the extent of the contamination of the biosphere, in the same way as is in operation for radionuclides, has been proposed for a number of the most harmful contaminants of the biosphere. The measurements are divided into measurements for the National Measuring Programme and additional Measurements. The former include the analyses essential for an efficacious control of the radioactivity of the biosphere. Measurements are performed in air, soil, surface water, milk and in deposition on the surface of the earth. Besides the determination of the usual radionuclides, as performed up to 1970, deposited radioactivity and surface water are also tested for some other specific radionuclides which may be set free at nuclear installations. Finally, samples of milk and grass from the surroundings of nuclear reactors and water from drinking-waterreservoirs have been analysed. Results are given of determination of tritium in drinking water of four big cities, and of radionuclides in some fishery products from the Dutch coastal waters in view of the potential of some marine organisms to concentrate fission products and especially activated corrosion products from nuclear installations. Adiitionally are given the results of measurements by the licensees of the Dutch nuclear installations of samples from the surroundings of their plants.

  8. Contaminant Release from Residual Waste in Single Shell Tanks at the Hanford Site, Washington, USA - 9276

    International Nuclear Information System (INIS)

    Cantrell, Kirk J.; Krupka, Kenneth M.; Deutsch, William J.; Lindberg, Michael J.

    2009-01-01

    Determinations of elemental and solid-phase compositions, and contaminant release studies have been applied in an ongoing study of residual tank wastes (i.e., waste remaining after final retrieval operations) from five of 149 underground single-shell storage tanks (241-C-103, 241-C-106, 241-C-202, 241-C-203, and 241-S-112) at the U.S. Department of Energy's Hanford Site in Washington State. This work is being conducted to support performance assessments that will be required to evaluate long-term health and safety risks associated with tank site closure. The results of studies completed to date show significant variability in the compositions, solid phase properties, and contaminant release characteristics from these residual tank wastes. This variability is the result of differences in waste chemistry/composition of wastes produced from several different spent fuel reprocessing schemes, subsequent waste reprocessing to remove certain target constituents, tank farm operations that concentrated wastes and mixed wastes between tanks, and differences in retrieval processes used to remove the wastes from the tanks. Release models were developed based upon results of chemical characterization of the bulk residual waste, solid-phase characterization (see companion paper 9277 by Krupka et al.), leaching and extraction experiments, and geochemical modeling. In most cases empirical release models were required to describe contaminant release from these wastes. Release of contaminants from residual waste was frequently found to be controlled by the solubility of phases that could not be identified and/or for which thermodynamic data and/or dissolution rates have not been measured. For example, significant fractions of Tc-99, I-129, and Cr appear to be coprecipitated at trace concentrations in metal oxide phases that could not be identified unambiguously. In the case of U release from tank 241-C-103 residual waste, geochemical calculations indicated that leachate

  9. Measurement of radioactive contamination and decontamination on wooden exteriors and garden trees in Northern Fukushima Prefecture

    International Nuclear Information System (INIS)

    Sugiura, Hiroyuki; Kawano, Keisuke; Kayama, Yukihiko

    2012-01-01

    Measurement and decontamination of surface of trees and surrounding wooden structures contaminated by radioactive substance were studied in the gardens and public parks of Northern Fukushima Prefecture which experienced radioactive contamination due to the accident at the TEPCO's Fukushima Daiichi Nuclear Power Plant. The counts per minute (CPM) above the centre surface of wooden garden tables in open air were 1.5 times higher than those of garden benches and 9 times higher than that of a garden bench in the square gazebo. Decontamination of wooden garden benches by high-pressure washing was more effective than planing. The counts per minute (CPM) above the soil around garden trees increased by 1.2 times after high-pressure washing. Radioactivity counting rate did not decrease when the leaves fallen from zelocova trees were removed; however, they decreased by about half when soil cover was installed at the base of the trees. Clearly, the upper surfaces of garden trees and wooden surrounding structures were strongly contaminated by radioactive substances, and they should be decontaminated by high-pressure washing before removing the surface soil. (author)

  10. Experimental study of contamination by inhalation of radioactive iodine aerosols. Biological balance; Etude experimentale de la contamination par inhalation d'aerosols d'iode radioactif bilan biologique

    Energy Technology Data Exchange (ETDEWEB)

    Marble, G [Commissariat a l' Energie Atomique, 92 - Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

    1968-07-01

    Several articles have been published concerning research into contamination produced by inhalation of radioactive iodine aerosols in monkeys. Results dealing with the biological balance of this contamination are presented and discussed in this report. (author) [French] L'etude experimentale de la contamination par inhalation d'aerosols d'iode radioactif effectuee chez le singe a fait l'objet de plusieurs publications. Les resultats concernant le bilan biologique de cette contamination sont presentes et discutes dans ce rapport. (auteur)

  11. SU-E-T-534: Level of Residual Radioactivity of Activated Parts of a Decommissioned Cyclotron

    International Nuclear Information System (INIS)

    Choi, HHF; Leung, TM; Chiu, TL; Yang, B; Wu, PM; Cheung, KY; Yu, SK

    2015-01-01

    Purpose: CTI cyclotron RDS-111 was used at the Hong Kong Sanatorium and Hospital (HKSH) to produce radiopharmaceuticals and radioactive tracers for diagnostic scans between 1999 and 2007. During the operation, some machine components became radioactive by activation. For the safety of staff, decommissioning took place in 2009, two years after the cyclotron had stopped operation. This study investigates the residual radioactivity and radionuclides found in different cyclotron components in 2014 in compliance with the local regulations in Hong Kong for transfer of radioactive waste. Methods: A representative sample of each part was counted using a high-purity germanium detector (manufacturer: ORTECT) for at least four hours. GammaVision, a multichannel analyzer software, was used to identify the radionuclides found in the cyclotron components, as well as the associated activities. A standard library and a Mariscotti peak search algorithm were used to identify the present radionuclides. Only radionuclides with half-life greater than 180 days were considered. Results: Among the components, the Havar target foil has the highest specific activity ((4.6±0.6)×10 2 Bq/g), with Co-60 being the most prominent ((3.8±0.5)×10 2 Bq/g). The total activity of the target foil, however, is still low due to its small mass of 0.04 g. Radioisotopes Mn-54 (46±6 Bq/g), Na-22 (6.8±0.8 Bq/g), Co-57 (7.3±0.9 Bq/g), and Fe-59 (6.0±0.9 Bq/g) have also been detected in the target foil. The target window holder and the vacuum window register a specific activity of 88.3±0.6 Bq/g and 48.6±0.1 Bq/g, respectively. Other components, such as the collimator, the target tube, the valve body and the beamline, are also found with trace amounts of radionuclides. Conclusion: Even seven years after the cyclotron had stopped operation, some components still exhibited residual radioactivity from activation exceeding the IAEA clearance levels. Special consideration for radiological protection may need

  12. A Novel Method for Remote Depth Estimation of Buried Radioactive Contamination.

    Science.gov (United States)

    Ukaegbu, Ikechukwu Kevin; Gamage, Kelum A A

    2018-02-08

    Existing remote radioactive contamination depth estimation methods for buried radioactive wastes are either limited to less than 2 cm or are based on empirical models that require foreknowledge of the maximum penetrable depth of the contamination. These severely limits their usefulness in some real life subsurface contamination scenarios. Therefore, this work presents a novel remote depth estimation method that is based on an approximate three-dimensional linear attenuation model that exploits the benefits of using multiple measurements obtained from the surface of the material in which the contamination is buried using a radiation detector. Simulation results showed that the proposed method is able to detect the depth of caesium-137 and cobalt-60 contamination buried up to 40 cm in both sand and concrete. Furthermore, results from experiments show that the method is able to detect the depth of caesium-137 contamination buried up to 12 cm in sand. The lower maximum depth recorded in the experiment is due to limitations in the detector and the low activity of the caesium-137 source used. Nevertheless, both results demonstrate the superior capability of the proposed method compared to existing methods.

  13. Development of Decontamination Technology for Separating Radioactive Constituents from Contaminated Concrete Waste

    International Nuclear Information System (INIS)

    Min, B. Y.; Kim, G. N.; Lee, G. W.; Choi, W. K.; Jung, U. S.

    2010-01-01

    The large amount of contaminated concrete produced during decommissioning procedures and available decontamination. In Korea, more than more than 60 tons of concrete wastes contaminated with uranium compounds have been generated from UCP (Uranium Conversion Plant) by dismantling. A recycling or a volume reduction of the concrete wastes through the application of appropriate treatment technologies have merits from the view point of an increase in a resource recycling as well as a decrease in the amount of wastes to be disposed of resulting in a reduction of a disposal cost and an enhancement of the disposal safety. For unconditional release of building and reduction of radioactive concrete waste, mechanical methods and thermal stress methods have been selected. In the advanced countries, such as France, Japan, Germany, Sweden, and Belgium, techniques for reduction and reuse of the decommissioning concrete wastes have applied to minimize the total radioactive concrete waste volume by thermal and mechanical processes. It was found that volume reduction of contaminated concrete can be achieved by separation of the fine cement stone and coarse gravel. Typically, the contaminated layer is only 1∼10mm thick because cementitious materials are porous media, the penetration of radionuclides may occur up to several centimenters from the surface of a material. Most of the dismantled concrete wastes are slightly contaminated rather than activated. This decontamination can be accomplished during the course of a separation of the concrete wastes contaminated with radioactive materials through a thermal treatment step of the radionuclide (e.g. cesium and strontium), transportation of the radionuclide to fine aggregates through a mechanical treatment step. Concrete is a structural material which generally consists of a binder (cement), water, and aggregate. The interaction between highly charged calcium silicate hydrate (C-S-H) particles in the presence of divalent calcium

  14. Derivation of guidelines for uranium residual radioactive material in soil at the New Brunswick Site, Middlesex County, New Jersey

    International Nuclear Information System (INIS)

    Dunning, D.; Kamboj, S.; Nimmagadda, M.; Yu, C.

    1996-02-01

    Residual radioactive material guidelines for uranium in soil were derived for the New Brunswick Site, located in Middlesex County, New Jersey. This site has been designated for remedial action under the Formerly Utilized Sites Remedial Action Program of the US Department of Energy (DOE). Residual radioactive material guidelines for individual radionuclides of concern and total uranium were derived on the basis of the requirement that the 50-year committed effective dose equivalent to a hypothetical individual who lives or works in the immediate vicinity of the New Brunswick Site should not exceed a dose of 30 mrem/yr following remedial action for the current-use and likely future-use scenarios or a dose of 100 mrem/yr for less likely future-use scenarios. The DOE residual radioactive material guideline computer code, RESRAD, was used in this evaluation; RESRAD implements the methodology described in the DOE manual for establishing residual radioactive material guidelines. The guidelines derived in this report are intended to apply to the remediation of these remaining residual radioactive materials at the site. The primary radionuclides of concern in these remaining materials are expected to be radium-226 and, to a lesser extent, natural uranium and thorium. The DOE has established generic cleanup guidelines for radium and thorium in soil; however, cleanup guidelines for other radionuclides must be derived on a site-specific basis

  15. Estimation of biological effects of phytocenosis radioactive contamination

    International Nuclear Information System (INIS)

    Suvorova, L.I.; Smirnov, E.G.; Shejn, G.N.

    1990-01-01

    Biological effects of argicultural field contamination in the Chernobyl NPP 30-km zone in the period of 1986-1988 are studies. Depth of some kings of herbs is noted in spite of natural phytocenosis high stability. It is revealed that increased mutageneous effect is observed for seeds from phytocenosis subjected to radiation factor effects. The genetic radiation effects at cell level will be observed in the nearest years as the radiation factor will not disappear in the 30-km zone (chronic irradiation of plants in the dose range from 0.1x10 -4 up to 0.1 Gy/day). These injuries visually will not effect greatly on natural populations

  16. Rechargeable particulate filter for radioactive contaminated gas streams

    International Nuclear Information System (INIS)

    Bonn, J.W.

    1976-01-01

    A system is disclosed which includes a closed housing having a plurality of rectangularly configured beds with perforated sidewalls longitudinally disposed in housing in laterally spaced disposition with each other. Alternate spaces at inlet end are closed and alternate spaces opposite the open ends are closed at exit end whereby contaminated gas is laterally squeezed through the beds filled with particulate adsorbent. The lower portions of the beds funnel into longitudinally extending discharge chutes enclosed within respective wells, the lower edges of the chutes rising at a constant angle above the well floor. An evacuation system coupled to the wells suctions the pile of particulate from the most remote portion of the chutes first. 3 claims, 7 drawing figures

  17. Residual viral and bacterial contamination of surfaces after cleaning and disinfection.

    Science.gov (United States)

    Tuladhar, Era; Hazeleger, Wilma C; Koopmans, Marion; Zwietering, Marcel H; Beumer, Rijkelt R; Duizer, Erwin

    2012-11-01

    Environmental surfaces contaminated with pathogens can be sources of indirect transmission, and cleaning and disinfection are common interventions focused on reducing contamination levels. We determined the efficacy of cleaning and disinfection procedures for reducing contamination by noroviruses, rotavirus, poliovirus, parechovirus, adenovirus, influenza virus, Staphylococcus aureus, and Salmonella enterica from artificially contaminated stainless steel surfaces. After a single wipe with water, liquid soap, or 250-ppm free chlorine solution, the numbers of infective viruses and bacteria were reduced by 1 log(10) for poliovirus and close to 4 log(10) for influenza virus. There was no significant difference in residual contamination levels after wiping with water, liquid soap, or 250-ppm chlorine solution. When a single wipe with liquid soap was followed by a second wipe using 250- or 1,000-ppm chlorine, an extra 1- to 3-log(10) reduction was achieved, and except for rotavirus and norovirus genogroup I, no significant additional effect of 1,000 ppm compared to 250 ppm was found. A reduced correlation between reduction in PCR units (PCRU) and reduction in infectious particles suggests that at least part of the reduction achieved in the second step is due to inactivation instead of removal alone. We used data on infectious doses and transfer efficiencies to estimate a target level to which the residual contamination should be reduced and found that a single wipe with liquid soap followed by a wipe with 250-ppm free chlorine solution was sufficient to reduce the residual contamination to below the target level for most of the pathogens tested.

  18. Comparison of public exposures from different sources of radioactive contamination in recent years in Slovenia

    International Nuclear Information System (INIS)

    Vokal, B.; Krizman, M.

    2003-01-01

    In spite of that Slovenia is a small country it contains a considerable variety of radioactive sources, which cause radioactive contamination of the environment. These sources mostly belong to nuclear fuel cycle, as the Krsko Nuclear Power Plant, the Zirovski vrh Uranium Mine (in the decommissioning), the TRIGA Research Reactor and Central low and intermediate level radioactive waste storage. Some other technological enhanced natural radiation sources, for example, the Sostanj Thermal Power Plant have also an impact to the environment. The comparison of the public exposure due to various sources of radioactive releases to the exposure of a members of the public in Slovenia shows that the critical group in the vicinity of the Zirovski Vrh uranium mine is the most exposed one in Slovenia. The global contamination due to the Chernobyl accident and the past nuclear tests was estimated to be around 10 μSv in Slovenia while the estimated annual dose for all other radioactive facilities are in the order of magnitude of one μSv. In this review the releases from the hospitals are not reported but some studies showed that it is not negligible. (authors)

  19. Hanford Tanks 241-C-202 and 241-C-203 Residual Waste Contaminant Release Models and Supporting Data

    Energy Technology Data Exchange (ETDEWEB)

    Deutsch, William J.; Krupka, Kenneth M.; Lindberg, Michael J.; Cantrell, Kirk J.; Brown, Christopher F.; Mattigod, Shas V.; Schaef, Herbert T.; Arey, Bruce W.

    2007-09-13

    As directed by Congress, the U. S. Department of Energy (DOE) established the Office of River Protection in 1998 to manage DOE's largest, most complex environmental cleanup project – retrieval of radioactive waste from Hanford tanks for treatment and eventual disposal. Sixty percent by volume of the nation's high-level radioactive waste is stored at Hanford in aging deteriorating tanks. If not cleaned up, this waste is a threat to the Columbia River and the Pacific Northwest. CH2M Hill Hanford Group, Inc., is the Office of River Protection's prime contractor responsible for the storage, retrieval, and disposal of Hanford's tank waste. As part of this effort, CH2M HILL Hanford Group, Inc. contracted with Pacific Northwest National Laboratory (PNNL) to develop release models for key contaminants that are present in residual sludge remaining after closure of Hanford Tanks 241-C-203 (C-203) and 241-C-204 (C-204). The release models were developed from data generated by laboratory characterization and testing of samples from these two tanks. These release models are being developed to support the tank closure risk assessments performed by CH2M HILL Hanford Group, Inc., for DOE.

  20. Measures to detect and control radioactive contaminated metallurgical scrap at border checkpoints in Poland

    International Nuclear Information System (INIS)

    Smagala, G.

    1999-01-01

    The issue of radioactive contaminated metallurgical scrap has never received a high priority in Poland and in the international community. Since the dissolution of the former Soviet Union a higher attention has been given to the problem. Poland which is located between the West and East Europe has the obligation to develop and implement an effective prevention and detection system. The reasons to increase national control and detection system at the border checkpoints in Poland are to avoid the following risks: post Chernobyl contamination transports of commodities; transport of contaminated metal scrap; transfer of radioactive waste for their disposal or utilization; high risk of becoming a transit country of illicit trafficking of nuclear materials and radioactive sources. In order to avoid the above-mentioned risks, Poland initiated in 1990, a deployment of the portable radiation devices at the border checkpoints and, as of 1998, the number of installed instruments exceeded a hundred. This paper presents Poland's activities to detect contaminated scrap at its border checkpoints. (author)