Using commercial simulators for determining flash distillation curves for petroleum fractions

Directory of Open Access Journals (Sweden)

Eleonora Erdmann

2008-01-01

Full Text Available This work describes a new method for estimating the equilibrium flash vaporisation (EFV distillation curve for petro-leum fractions by using commercial simulators. A commercial simulator was used for implementing a stationary mo-del for flash distillation; this model was adjusted by using a distillation curve obtained from standard laboratory ana-lytical assays. Such curve can be one of many types (eg ASTM D86, D1160 or D2887 and involves an experimental procedure simpler than that required for obtaining an EFV curve. Any commercial simulator able to model petroleum can be used for the simulation (HYSYS and CHEMCAD simulators were used here. Several types of petroleum and fractions were experimentally analysed for evaluating the proposed method; this data was then put into a process si-mulator (according to the proposed method to estimate the corresponding EFV curves. HYSYS- and CHEMCAD-estimated curves were compared to those produced by two traditional estimation methods (Edmister’s and Maswell’s methods. Simulation-estimated curves were close to average Edmister and Maxwell curves in all cases. The propo-sed method has several advantages; it avoids the need for experimentally obtaining an EFV curve, it does not de-pend on the type of experimental curve used to fit the model and it enables estimating several pressures by using just one experimental curve as data.

Determination of petroleum fractions as contaminants in the waters by gas chromatography

International Nuclear Information System (INIS)

Kubinec, R.; Mracnova, R.; Kuran, P.; Ostrovsky, I.; Sojak, L.

1995-01-01

The method of micro-extraction of petroleum fractions from water and analysis using gas chromatography was developed. This method can be used for the analysis of gaseous oil and mineral oil in the water wit the detection limit 12 ppb and 18 ppb, respectively

The petroleum refining industry and the implications for the environment

International Nuclear Information System (INIS)

Saraiva, Gerardo Jose de Pontes

2000-01-01

The petroleum refining industry is basically concerned with the production of oil, lubricants and intermediate petrochemical products, utilizing crude oil as its main raw material. Petroleum refining, a distillation process that breaks hydrocarbons into fractions, eliminating undesired impurities, generates irreducible residues. Until the industrial revolution, the residues were essentially organic, susceptible to the attack of agents of destruction and transformation (bacterium, fungi, etc). Suddenly, due to the intensification of human activities of modern man, nature scattered across the planet more resistant products, many of them with long life times, that produce a deeper impact in the environment. Almost entirely marine is the pollution that results from increasing quantity of hydrocarbons dumped into the sea, a problem that is aggravated by the development of manufacturing and transportation of petroleum products. The expansion of the petroleum commerce, using essentially maritime transportation, has increased considerably the probability of accidents increasing the risks of environment pollution. This work presents suggestions and possible solutions to minimize the problem of environment pollution, caused by refining and transportation of this combustible, essential to present time industry. (author)

Evaluation of gastrointestinal solubilization of petroleum hydrocarbon residues in soil using an in vitro physiologically based model.

Science.gov (United States)

Holman, Hoi-Ying N; Goth-Goldstein, Regine; Aston, David; Yun, Mao; Kengsoontra, Jenny

2002-03-15

Petroleum hydrocarbon residues in weathered soils may pose risks to humans through the ingestion pathway. To understand the factors controlling their gastrointestinal (GI) absorption, a newly developed experimental extraction protocol was used to model the GI solubility of total petroleum hydrocarbon (TPH) residues in highly weathered soils from different sites. The GI solubility of TPH residues was significantly higher for soil contaminated with diesel than with crude oil. Compared to the solubility of TPH residues during fasted state,the solubility of TPH residues during fat digestion was much greater. Diesel solubility increased from an average of 8% during the "gallbladder empty" phase of fasting (and less than 0.2% during the otherfasting phase) to an average of 16% during fat digestion. For crude oil, the solubility increased from an average of 1.2% during the gallbladder empty phase of fasting (and undetectable during the other fasting phase) to an average of 4.5% during fat digestion. Increasing the concentration of bile salts also increased GI solubility. GI solubility was reduced by soil organic carbon but enhanced by the TPH content.

Stabilization of Bio-Oil Fractions for Insertion into Petroleum Refineries

Energy Technology Data Exchange (ETDEWEB)

Brown, Robert C. [Iowa State Univ., Ames, IA (United States); Smith, Ryan [Iowa State Univ., Ames, IA (United States); Wright, Mark [Iowa State Univ., Ames, IA (United States); Elliott, Douglas [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Resasco, Daniel [Univ. of Oklahoma, Norman, OK (United States); Crossley, Steven [Univ. of Oklahoma, Norman, OK (United States)

2014-09-28

This project is part of a collaboration effort between Iowa State University (ISU), University of Oklahoma (OK) and Pacific Northwest National Laboratory (PNNL). The purpose of this project is to stabilize bio-oil fractions and improve their suitability for insertion into petroleum refineries. Bio-oil from fast pyrolysis of biomass is a complex mixture of unstable organic compounds. These organic compounds react under standard room conditions resulting in increases in bio-oil viscosity and water content – both detrimental for bio-oil storage and transportation. This study employed fractionation and upgrading systems to improve the stability of bio-oil. The fractionation system consists of a series of condensers, and electrostatic precipitators designed to separate bio-oil into five fractions: soluble carbohydrates (SF1&2), clean phenolic oligomers (CPO) and middle fraction (SF3&4), light oxygenates (SF5). A two-stage upgrading process was designed to process bio-oil stage fractions into stable products that can be inserted into a refinery. In the upgrading system, heavy and middle bio-oil fractions were upgraded into stable oil via cracking and subsequent hydrodeoxygenation. The light oxygenate fraction was steam reformed to provide a portion of requisite hydrogen for hydroprocessing. Hydrotreating and hydrocracking employed hydrogen from natural gas, fuel gas and light oxygenates reforming. The finished products from this study consist of gasoline- and diesel-blend stock fuels.

40 CFR Table 5 to Subpart Oooo of... - Default Organic HAP Mass Fraction for Petroleum Solvent Groups a

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Default Organic HAP Mass Fraction for... 63—Default Organic HAP Mass Fraction for Petroleum Solvent Groups a You may use the mass fraction... formulation data: Solvent type Averageorganic HAP mass fraction Typical organic HAP, percent by mass Aliphatic...

Thermal and catalytic decomposition behavior of PVC mixed plastic waste with petroleum residue

Energy Technology Data Exchange (ETDEWEB)

Ali, Mohammad Farhat; Siddiqui, Mohammad Nahid [Department of Chemistry, King Fahd University of Petroleum and Minerals, Dhahran 31261 (Saudi Arabia)

2005-08-15

The pyrolysis and hydropyrolysis of PVC mixed plastic waste alone and with petroleum residue was carried out at 150 and 350{sup o}C under N{sub 2} gas and at 430{sup o}C under 6.5MPa H{sub 2} gas pressure. The behavior of plastic waste during thermal and catalytic decomposition has also been studied in single- and two-stage reaction processes. In the individual pyrolysis process, both the petroleum residue and polystyrene (PS) undergo more than 90% conversion to liquid and gaseous products, whereas low-density polyethylene (LDPE) and high-density polyethylene (HDPE) yielded lower conversions products, and polypropylene (PP) and polyvinyl chloride (PVC) afforded somewhere a moderate to high conversion products. In a single-stage pyrolysis reaction, PVC was processed with petroleum residue at 150 and 430{sup o}C, under N{sub 2} gas for 1h at each temperature in a glass reactor. The model PVC and waste PVC showed slight variations in the products distribution obtained from the glass reactor. In two-stage process, model PVC, vacuum gas oil (VGO) and a number of different catalysts were used in a stainless steel autoclave micro tubular reactor at 350{sup o}C under the stream of N{sub 2} gas for 1h and at 430{sup o}C under 950psi (6.5MPa) H{sub 2} pressure for the duration of 2h. Significantly, different products distributions were obtained. Among the catalysts used, fluid catalytic cracking (FCC) and hydrocracking catalysts (HC-1) were most effective in producing liquid fuel (hexane soluble) materials. The study shows that the catalytic coprocessing of PVC with VGO is a feasible process by which PVC and VGO materials can be converted into transportation fuels.

Distribution and Fractional Composition of Petroleum Hydrocarbons in Roadside Soils

Directory of Open Access Journals (Sweden)

Larysa Mykhailova

2013-01-01

Full Text Available Total petroleum hydrocarbon (TPH concentrations and their fractional composition (medium fraction: n-alkane chain-length C15 to C27, heavy fraction: >C27 were determined at distances from 1 to 60 m from roads and at soil depths from 0.5 to 15 cm. The traffic intensities were up to 25000 vehicles per day. Soil TPH concentrations were highest within 15 m distance (665 and 3198 mg kg−1 at the windward and leeward sides, resp., followed by a rapid drop to background values beyond (196 and 115 mg kg−1 in 60 m distance at the windward and leeward sides, resp.. The data variability was lowest at distances of 1 m and highest within tree plantations at distances of 15 m from the road. The TPH concentrations decreased with depth but were significantly higher than the background at all depths investigated. A principal component analysis revealed a positive relation between the medium-to-heavy fraction ratio and soil depth. A fractional differentiation of hydrocarbons with distance from road was not observed. It was concluded that the assessment of the potential of hydrocarbons to translocate, accumulate, or degrade in soil necessitates their subdivision into fractions based on their physicochemical and metabolic properties.

Comparative acute toxicity of shale and petroleum derived distillates.

Science.gov (United States)

Clark, C R; Ferguson, P W; Katchen, M A; Dennis, M W; Craig, D K

1989-12-01

In anticipation of the commercialization of its shale oil retorting and upgrading process, Unocal Corp. conducted a testing program aimed at better defining potential health impacts of a shale industry. Acute toxicity studies using rats and rabbits compared the effects of naphtha, Jet-A, JP-4, diesel and "residual" distillate fractions of both petroleum derived crude oils and hydrotreated shale oil. No differences in the acute oral (greater than 5 g/kg LD50) and dermal (greater than 2 g/kg LD50) toxicities were noted between the shale and petroleum derived distillates and none of the samples were more than mildly irritating to the eyes. Shale and petroleum products caused similar degrees of mild to moderate skin irritation. None of the materials produced sensitization reactions. The LC50 after acute inhalation exposure to Jet-A, shale naphtha, (greater than 5 mg/L) and JP-4 distillate fractions of petroleum and shale oils was greater than 5 mg/L. The LC50 of petroleum naphtha (greater than 4.8 mg/L) and raw shale oil (greater than 3.95 mg/L) also indicated low toxicity. Results demonstrate that shale oil products are of low acute toxicity, mild to moderately irritating and similar to their petroleum counterparts. The results further demonstrate that hydrotreatment reduces the irritancy of raw shale oil.

40 CFR Table 4 to Subpart Mmmm of... - Default Organic HAP Mass Fraction for Petroleum Solvent Groups a

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Default Organic HAP Mass Fraction for... Part 63—Default Organic HAP Mass Fraction for Petroleum Solvent Groups a You may use the mass fraction... formulation data. Solvent type Average organic HAP mass fraction Typical organic HAP, percent by mass...

40 CFR Table 4 to Subpart Pppp of... - Default Organic HAP Mass Fraction for Petroleum Solvent Groups a

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Default Organic HAP Mass Fraction for... Organic HAP Mass Fraction for Petroleum Solvent Groups a You may use the mass fraction values in the.... Solvent type Averageorganic HAP mass fraction Typical organic HAP, percent by mass Aliphatic b 0.03 1...

40 CFR Table 4 to Subpart IIIi of... - Default Organic HAP Mass Fraction for Petroleum Solvent Groups a

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Default Organic HAP Mass Fraction for... Organic HAP Mass Fraction for Petroleum Solvent Groups a You may use the mass fraction values in the... Solvent type Averageorganic HAP mass fraction Typical organic HAP, percent by mass Aliphatic b 0.03 1...

40 CFR Table 6 to Subpart Qqqq of... - Default Organic HAP Mass Fraction for Petroleum Solvent Groups a

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Default Organic HAP Mass Fraction for... HAP Mass Fraction for Petroleum Solvent Groups a You may use the mass fraction values in the following... type Average organic HAP mass fraction Typical organic HAP, percent by mass Aliphatic b 0.03 1% xylene...

Petroleum residues degradation in laboratory-scale by rhizosphere bacteria isolated from the mangrove ecosystem

Science.gov (United States)

Rinanti, A.; Nainggolan, I. J.

2018-01-01

This research is about petroleum bioremediation experiment to obtain bacterial isolate from mangrove ecosystem which potentially degrade petroleum. It was conducted in an Erlenmeyer batch system filled with growth medium of Stone Mineral Salt Solution (SMSS) plus petroleum residue, placed in an incubator shaker with a rotation speed of 120 rpm, temperature 3000C, for 14 research days. Indigenous bacteria that have been isolated and identified from the roots of mangrove plants are Ochrobactrum anthropi and Bacillus sp., Ralstonia pickettii and Bacillus circulans. Those bacteriain both monoculture and consortium form (mixed culture) are incorporated into erlenmeyer as remediator agents. All bacteria can utilize hydrocarbon compounds, but Ralstonia pickettii and Bacillus circulans reached exponential phase faster with more cell count than other bacteria. Compared to single cultures, petroleum degradation by a bacterial consortium provides a higher TPH reduction efficiency, i.e. at 5%, 10%, and 15% of initial TPH of 94.4%, 72%, and 80.3%, respectively. This study proved that all bacteria could optimize hydrocarbon compounds up to 15% TPH load.

An In Silico Approach for Evaluating a Fraction-Based, Risk Assessment Method for Total Petroleum Hydrocarbon Mixtures

Directory of Open Access Journals (Sweden)

Nina Ching Y. Wang

2012-01-01

Full Text Available Both the Massachusetts Department of Environmental Protection (MADEP and the Total Petroleum Hydrocarbon Criteria Working Group (TPHCWG developed fraction-based approaches for assessing human health risks posed by total petroleum hydrocarbon (TPH mixtures in the environment. Both organizations defined TPH fractions based on their expected environmental fate and by analytical chemical methods. They derived toxicity values for selected compounds within each fraction and used these as surrogates to assess hazard or risk of exposure to the whole fractions. Membership in a TPH fraction is generally defined by the number of carbon atoms in a compound and by a compound's equivalent carbon (EC number index, which can predict its environmental fate. Here, we systematically and objectively re-evaluate the assignment of TPH to specific fractions using comparative molecular field analysis and hierarchical clustering. The approach is transparent and reproducible, reducing inherent reliance on judgment when toxicity information is limited. Our evaluation of membership in these fractions is highly consistent (̃80% on average across various fractions with the empirical approach of MADEP and TPHCWG. Furthermore, the results support the general methodology of mixture risk assessment to assess both cancer and noncancer risk values after the application of fractionation.

The influence of petroleum asphaltenic sub fractions on the demulsifiers performance; Influencia de subfracoes asfaltenicas de petroleo sobre a acao de desemulsificantes

Energy Technology Data Exchange (ETDEWEB)

Honse, Siller O.; Mansur, Claudia R.E.; Lucas, Elizabete F. [Universidade Federal do Rio de Janeiro (IMA/UFRJ), RJ (Brazil). Inst. de Macromoleculas. Lab. de Macromoleculas e Coloides na Industria de Petroleo], e-mail: celias@ima.ufrj.br

2011-07-01

The aim of this work is to evaluate the influence of asphaltene fractions and subfractions on the stabilization of petroleum emulsions, as well as on the efficiency of demulsifiers based on poly(ethylene oxide-b-propylene oxide) (PEO-PPO). Asphaltenes were extracted from an asphaltic residue using n-heptane (C5 asphaltenes) and n-decane (asphaltenes C10). Intermediate subfractions were also obtained. Model emulsions, consisted of water and dispersions of the asphaltene in toluene were prepared, with and without adding demulsifier. The stability of the emulsions was higher when adding more polar fractions. However, asphaltenes presenting a broad distribution of polarity cause higher emulsion stability than that presenting very narrow distribution of intermediate polarity. The efficiency of PEO-PPO copolymer on emulsions separation is related to the original stability of the emulsions. In this work, it was confirmed that branched surfactant presents higher efficiency than the linear. (author)

Occurrence of pesticide non extractable residues in physical and chemical fractions from two natural soils.

Science.gov (United States)

Andreou, K.; Jones, K.; Semple, K.

2009-04-01

Distribution of pesticide non extractable residues resulted from the incubation of two natural soils with each of the isoproturon, diazinon and cypermethrin pesticide was assessed in this study. Pesticide non extractable residues distribution in soil physical and chemical fractions is known to ultimately affect their fate. This study aimed to address the fate and behaviour of the non extractable residues in the context of their association with soil physical and chemical fractions with varying properties and characteristics. Non extractable residues were formed from incubation of each pesticide in the two natural soils over a period of 24 months. Soils containing the non extractable residues were fractionated into three solid phase fractions using a physical fractionation procedure as follows: Sediment (SED, >20 μm), (II) Microaggregate (MA, 20-2 μm) and (III) Colloid phase (COL, 2-0.05 μm). Each soil fraction was then fractionated into organic carbon chemical fractionations as follows: Fulvic acid (FA), Humic acid (HA) and Humin (HM). Significant amount of the pesticides was lost during the incubation period. Enrichment factors for the organic carbon and the 14C-pesticide residues were higher in the MA and COL fraction rather than the SED fraction. Greater association and enrichment of the fulvic acid fraction of the organic carbon in the soil was observed. Non extractable residues at the FA fraction showed to diminish while in the HA fraction were increased with decreasing the fraction size. An appreciable amount of non extractable residues were located in the HM fraction but this was less than the amount recovered in the humic substances. Long term fate of pesticide non extractable residues in the soil structural components is important in order to assess any risk associated with them.

Using commercial simulators for determining flash distillation curves for petroleum fractions

OpenAIRE

Eleonora Erdmann; Demetrio Humana; Samuel Franco Domínguez; Lorgio Mercado Fuentes

2010-01-01

This work describes a new method for estimating the equilibrium flash vaporisation (EFV) distillation curve for petro-leum fractions by using commercial simulators. A commercial simulator was used for implementing a stationary mo-del for flash distillation; this model was adjusted by using a distillation curve obtained from standard laboratory ana-lytical assays. Such curve can be one of many types (eg ASTM D86, D1160 or D2887) and involves an experimental procedure simpler than that required...

Analysis of petroleum oily sludge producing in petroleum field of Rio Grande do Norte, Brazil

Energy Technology Data Exchange (ETDEWEB)

Lima, Cicero de Souza; Lima, Regineide Oliveira; Silva, Edjane Fabiula Buriti da; Castro, Kesia Kelly Vieira de; Chiavone Filho, Osvaldo; Araujo, Antonio Souza de [Universidade Federal do Rio Grande do Norte (UFRN), RN (Brazil)

2012-07-01

In exploration and production of petroleum is generated solid waste different and components other. The petroleum oily sludge is a complex mix of components different (water, oil and solid). The petroleum oily sludge generally has other residues and is formed during production and operations, transport, storage and petroleum refining (atmospheric residue, vacuum residue and catalytic cracking residue). However, according to its origin, the compositions can be found quite varied for sludge. Observing the process steps production and refining is possible to locate its main sources and percentage contributions in terms of waste generation. The elemental analysis was performed with oily sludge from region and it showed different composition. For carbon element and hydrogen, small differences was observed, but for was observed greater differences for Oxygen element. The sludge has different inorganic and organic composition. The sludge from oil water separator (OWS) 2 showed a greater amount of oil (94.88%), this may indicate a residue of aggregate high for petroleum industry. In analysis of Saturates, Aromatics, Resins and Asphaltenes (SARA), the sludge from unloading showed amount high of saturates. The inorganic material separated from sludge was characterized and sludge from OWS 2 had high amount sulfur (41.57%). The sludge analyzed showed organic components high values, so it can be treated and reprocessed in process units petroleum industry. The analysis thermal degradation had a better setting for treated oily sludge. (author)

Bulbophyllum sterile petroleum ether fraction induces apoptosis in vitro and ameliorates tumor progression in vivo.

Science.gov (United States)

Biswas, Subhankar; Pardeshi, Rashmi; Reddy, Neetinkumar D; Shoja, Muhammed Haneefa; Nayak, Pawan G; Setty, M Manjunath; Pai, K Sreedhara R

2016-12-01

Orchids of the genus Bulbophyllum have been reported to possess antitumor activity. Present study investigated the possible antitumor activity of the active fraction of bulb and root of Bulbophyllum sterile. Alcoholic extract along with petroleum ether, dichloromethane and ethyl acetate fractions were subjected to SRB assay in HCT-116, MDA-MB-231 and A549 cell lines. The active fractions were further evaluated for apoptosis, expression of apoptotic signaling proteins, comet assay and cell cycle analysis. Furthermore, they were assessed for in vivo antitumor activity in Ehrlich ascites carcinoma model. Petroleum fraction of bulbs (PFB) and roots (PFR) was found to be most active in HCT-116 cell lines with IC 50 value of 94.2±6.0 and 75.7±9.8, respectively. Apoptosis was evident from acridine orange/ethidium bromide staining along with the expression of phospho-p53 and phospho-Bad. Both PFB and PFR arrested G 2 /M phase of the cell cycle with 32.6% and 49.4% arrest, respectively compared to 17.5% arrest with control. An increase in mean life span and hepatic antioxidant levels was observed with PFB and PFR treatment in EAC inoculated mice. The results suggested that the active fractions of bulbs and roots possess anticancer activity likely by inducing apoptosis through phospho-p53 dependent pathway. Copyright © 2016 Elsevier Masson SAS. All rights reserved.

Simulation of enhanced in-situ biorestoration of petroleum hydrocarbons

International Nuclear Information System (INIS)

Borden, R.C.

1991-01-01

This paper discusses a general mathematical model being developed to aid in the design and analysis of projects for the enhanced aerobic bioremediation of petroleum-contaminated aquifers. Development of the enhanced biotransformation model is proceeding in three steps: development of an abiotic hydrocarbon dissolution model; coupling the dissolution model with existing equations for simulating aerobic biodegradation; and comparison with laboratory data. The model assumes that the residual hydrocarbon is distributed between two fractions, a fast fraction in equilibrium with the aqueous phase and a slow fraction in which mass transfer is limited. Overall, the model provides an excellent fit to the experimental data and requires a minimum of input parameters

Residual power series method for fractional Sharma-Tasso-Olever equation

Directory of Open Access Journals (Sweden)

Amit Kumar

2016-02-01

Full Text Available In this paper, we introduce a modified analytical approximate technique to obtain solution of time fractional Sharma-Tasso-Olever equation. First, we present an alternative framework of the Residual power series method (RPSM which can be used simply and effectively to handle nonlinear fractional differential equations arising in several physical phenomena. This method is basically based on the generalized Taylor series formula and residual error function. A good result is found between our solution and the given solution. It is shown that the proposed method is reliable, efficient and easy to implement on all kinds of fractional nonlinear problems arising in science and technology.

Chemical reaction engineering studies on cocracking of petroleum vacuum residue with coal, plastics, and biomass (bagasse and petrocrop)

Energy Technology Data Exchange (ETDEWEB)

Ahmaruzzaman, M.; Sharma, D.K. [Indian Institute of Technology, New Delhi (India). Centre for Energy Studies

2007-07-01

This article deals with the studies on cocracking of petroleum vacuum residue (XVR) with thermosetting plastic, I. e., bakelite (BL), Samla coal (SC), biomass, I. e., bagasse (BG) or C. procera (CL) and their binary, ternary, and quaternary mixtures in a thermogravimetric analyzer (TGA). The kinetic studies were performed using the Coats and Redfern kinetic modeling equation. The overall activation energies obtained were 25 kJ/mole for petroleum vacuum residue, 99 kJ/mole for polypropylene, 21 kJ/mole for coal, 23 kJ/mole for Calotropis procera, and 25 kJ/mole for the combination of these four materials. However, other models, such as van Krevelan et al. and Horowitz and Metzger have also been used in some cases to compare the results with those obtained by the Coats and Redfern kinetic models. In the present work, the effect of catalysts on the cracking of Basra vacuum residue (BVR) has also been reported.

Modified sequential extraction for biochar and petroleum coke: Metal release potential and its environmental implications.

Science.gov (United States)

von Gunten, Konstantin; Alam, Md Samrat; Hubmann, Magdalena; Ok, Yong Sik; Konhauser, Kurt O; Alessi, Daniel S

2017-07-01

A modified Community Bureau of Reference (CBR) sequential extraction method was tested to assess the composition of untreated pyrogenic carbon (biochar) and oil sands petroleum coke. Wood biochar samples were found to contain lower concentrations of metals, but had higher fractions of easily mobilized alkaline earth and transition metals. Sewage sludge biochar was determined to be less recalcitrant and had higher total metal concentrations, with most of the metals found in the more resilient extraction fractions (oxidizable, residual). Petroleum coke was the most stable material, with a similar metal distribution pattern as the sewage sludge biochar. The applied sequential extraction method represents a suitable technique to recover metals from these materials, and is a valuable tool in understanding the metal retaining and leaching capability of various biochar types and carbonaceous petroleum coke samples. Copyright © 2017 Elsevier Ltd. All rights reserved.

Influence of humic fractions on retention of isoproturon residues in two Moroccan soils.

Science.gov (United States)

Elkhattabi, Kaouakeb; Bouhaouss, Ahmed; Scrano, Laura; Lelario, Filomena; Bufo, Sabino A

2007-01-01

The influence of different fractions of soil organic matter on the retention of the herbicide isoproturon (IPU) has been evaluated. Water and methanol extractable residues of (14)C labeled isoproturon have been determined in two Moroccan soils by beta -counting-liquid chromatography. The quantification of bound residues in soil and in different fractions of soil humic substances has been performed using pyrolysis/scintillation-detected gas-chromatography. Microbial mineralization of the herbicide and soil organic matter has been also monitored. Retention of isoproturon residues after 30-days incubation ranged from 22% to 32% (non-extractable fraction). The radioactivity extracted in an aqueous environment was from 20% to 33% of the amount used for the treatment; meanwhile, methanol was able to extract another 48%. Both soils showed quantities of bound residues into the humin fraction higher than humic and fulvic acids. The total amount of residues retained into the organic matter of the soils was about 65 % of non-extractable fraction, and this percentage did not change with incubation time; on the contrary, the sorption rate of the retention reaction is mostly influenced by the clay fraction and organic content of the soil. Only a little part of the herbicide was mineralized during the experimental time.

Petroleum residue upgrading with dispersed catalysts: Part 2. Effect of operating conditions

Energy Technology Data Exchange (ETDEWEB)

Panariti, N.; Del Bianco, A.; Del Piero, G. [ENITECNOLOGIE S.p.A, Via Maritano 26, 20097 San Donato Mil (Italy); Marchionna, M. [SNAMPROGETTI S.p.A, Via Maritano 26, 20097 San Donato Mil (Italy); Carniti, P. [Universita degli Studi di Milano, Dip. Chimica Fisica ed Elettrochimica, Via Celoria 20, Milan (Italy)

2000-12-04

The hydrotreatment of a petroleum residue in the presence of dispersed molybdenite was carried out within a wide range of operating conditions and catalyst loading. The effect of reaction severity as well as of molybdenum concentration on product distribution and quality was studied. Based on the experimental results, a simplified reaction scheme was proposed. The hydroprocessing of the residue was described in terms of the competition between two reactions: the direct conversion of the feedstock to distillate and coke, and the catalytic hydrogenation. Compared to thermal conditions, the presence of dispersed molybdenite controls very well coke formation; however, a trend of increasing formation of solids was observed at high catalyst concentrations. The overall upgrading of the feedstock requires significant amounts of molybdenum as well as relatively high hydrogen pressure.

Process from removing benzine, toluene, etc. , from petroleum residues, coal tar, and shale tar, etc

Energy Technology Data Exchange (ETDEWEB)

Hlawaty, F

1888-08-11

A process is described for the preparation of ligroin and its homologs as well as naphthalene and anthracene consisting in leading superheated water vapor into a mixture of petroleum residues (or mineral coal tar, etc.) heated to about 400/sup 0/C with cellulosic substances as sage shreds, sea grass, or straw, with addition of caustic alkali.

Coking of residue hydroprocessing catalysts

Energy Technology Data Exchange (ETDEWEB)

Gray, M.R.; Zhao, Y.X. [Alberta Univ., Edmonton, AB (Canada). Dept. of Chemical Engineering; McKnight, C.A. [Syncrude Canada Ltd., Edmonton, AB (Canada); Komar, D.A.; Carruthers, J.D. [Cytec Industries Inc., Stamford, CT (United States)

1997-11-01

One of the major causes of deactivation of Ni/Mo and Co/Mo sulfide catalysts for hydroprocessing of heavy petroleum and bitumen fractions is coke deposition. The composition and amount of coke deposited on residue hydroprocessing catalysts depends on the composition of the liquid phase of the reactor. In the Athabasca bitumen, the high molecular weight components encourage coke deposition at temperatures of 430 to 440 degrees C and at pressures of 10 to 20 MPa hydrogen pressure. A study was conducted to determine which components in the heavy residual oil fraction were responsible for coking of catalysts. Seven samples of Athabasca vacuum residue were prepared by supercritical fluid extraction with pentane before being placed in the reactor. Carbon content and hydrodesulfurization activity was measured. It was concluded that the deposition of coke depended on the presence of asphaltenes and not on other compositional variables such as content of nitrogen, aromatic carbon or vanadium.

Characterization of commercial ceramic adsorbents and its application on naphthenic acids removal of petroleum distillates

Directory of Open Access Journals (Sweden)

Juliana Pereira Silva

2007-06-01

Full Text Available The mixture of carboxylic acids present in petroleum oil and directly responsible for its acidity and corrosiveness in liquid phase during the refine process is denominated "naphthenic acids". These acids are also present in distilled fraction of petroleum, causing several problems in final products quality. A possible way to remove the carboxilic acids from petroleum distilled fractions is the adsorption in porous materials. However, the results obtained until now indicate that ion exchange resins would be the best adsorbents for this process, which would probably increase its cost. In this work, two commercial adsorbents (clay and activated alumina were characterized by a set of physical-chemistry techniques and evaluated concerning their capacity of removing naphthenic acids from a light petroleum fraction. It was verified the influence of a thermal treatment previous to the adsorption in its physical-chemistry characteristics and its properties. A high reduction of the TAN values was verified in the residual oils from both adsorbent, although there was a competition among all the compounds present in the light oil fraction for the adsorption sites, which can be probably related to the thermal pre-treatment. These results were related to corrosion yield experiments, and it was observed that the adsorbent pretreatment also affected the reduction in corrosion yields for both alumina and clay.

Petroleum marketing monthly

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-08-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly.

Petroleum marketing monthly

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-07-01

Petroleum Marketing Monthly (PPM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o. b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly.

Petroleum marketing monthly

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-02-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly.

Identification of key oil refining technologies for China National Petroleum Co. (CNPC)

International Nuclear Information System (INIS)

Liu Haiyan; Yu Jianning; Xu Jian; Fan Yu; Bao Xiaojun

2007-01-01

This paper summarizes the results from the project 'Vision of the Key Petroleum Refining Technologies for China National Petroleum Co. (CNPC) in the Early 21st Century' undertaken by the Department of R and D Administration, CNPC, and its affiliate key laboratory, The Key Laboratory of Catalysis operated by China University of Petroleum, Beijing. The objective of the project was to identify the challenges and opportunities of CNPC's petroleum refining business given increasing economy globalization and stricter environmental regulations. Using the modified Delphi method, four key technologies for CNPC's oil refining industry were identified. They are: integrated fluid catalytic cracking (FCC), hydroprocessing, residue hydrocracking, and high-grade lubricant production. The most significant technology will be the integrated FCC technology that can economically increase the yield of light fractions as well as upgrade transportation fuels. In China, FCC units produce about 80% and 30% commercial gasoline and diesel, respectively. To ensure compliance with future environmental legislation, hydroprocessing technologies, including those related to petroleum product hydrorefining and distillate hydrocracking, should be developed. By combining residue hydrocracking and FCC technologies, poorer quality residua can be processed. Supplying high-grade lube oils is one of the main tasks for CNPC's oil refining industry. Development of hydrodewaxing technologies to manufacture API group II/III base oil is the main direction for CNPC's lubricant production business

[Compositions and residual properties of petroleum hydrocarbon in contaminated soil of the oilfields].

Science.gov (United States)

Hu, Di; Li, Chuan; Dong, Qian-Qian; Li, Li-Ming; Li, Guang-He

2014-01-01

The aims of this study were to determine the compositions and residual properties of petroleum hydrocarbon in soil, as well as to identify the source and weathering degree of the pollution. A total of 5 producing wells in Gudao and Hekou oil producing region of Shengli oilfields were analyzed. More than 50 individual target compounds including straight-and branched-chain alkanes( n-alkanes, pristine and phytane) and polycyclic aromatic hydrocarbons (PAHs) in soil samples and crude oil were determined by gas chromatography-mass spectrometry (GC-MS). The percentages of chain alkanes and PAHs in total solvent extractable matters(TSEM) of soil samples were both much lower than those in the crude oil samples. The compositions of petroleum hydrocarbon in soil samples differed from those in crude oil, which indicated the n-alkanes with carbon numbers contaminated soils, the relationship between the index and petroleum hydrocarbon compounds was analyzed using principal component analysis (PCA). The results showed that the n-alkanes with carbon numbers > 33 and the PAHs with rings between 3 and 5 were much harder to degrade. PCA of 4 indexes for source identification revealed more than 50% of the soil samples were polluted by crude oil, which needs more attention during remediation.

Petroleum marketing monthly

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-11-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data.

Occurrence of non extractable pesticide residues in physical and chemical fractions of two soils

Science.gov (United States)

Andreou, Kostas; Semple, Kirk; Jones, Kevin

2010-05-01

Soils are considered to be a significant sink for organic contaminants, including pesticides, in the environment. Understanding the distribution and localisation of aged pesticide residues in soil is of great importance for assessing the mobility and availability of these chemicals in the environment. This study aimed to characterise the distribution of radiolabeled herbicide isoproturon and the radiolabeled insecticides diazinon and cypermethrin in two organically managed soils. The soils were spiked and aged under laboratory conditions for 17 months. The labile fraction of the pesticides residues was recovered in CaCl2 (0.01M) and then subjected to physical size fractionation using sedimentation and centrifugation steps, with >20μm, 20-2μm and 2-0.1μm soil factions collected. Further, the distribution of the pesticide residues in the organic matter of the fractionated soil was investigated using a sequential alkaline extraction (0.1N NaOH) into humic and fulvic acid and humin. Soil fractions of 20-2μm and 2-0.1μm had the largest burden of the 14C-residues. Different soil constituents have different capacities to form non-extractable residues. Soil solid fractions of 20-2 µm and 20 µm). Fulvic acid showed to play a vital role in the formation and stabilisation of non-extractable 14C-pesticide residues in most cases.Assessment of the likelihood of the pesticide residues to become available to soil biota requires an understanding of the structure of the SOM matrix and the definition of the kinetics of the pesticide residues in different SOM pools as a function of the time.

Evolution of wettability in terms of petroleum and petroleum fractions adsorption. An approach by the Wilhelmy method; Evolution de la mouillabilite en fonction de l`adsorption du petrole et de ses fractions. Approche par la methode des angles de contact dynamiques

Energy Technology Data Exchange (ETDEWEB)

Mattos Saliba, A

1996-12-06

Reservoir wettability is very important to petroleum recovery by waterflooding and other processes. It is a key parameter controlling multiphase flow and fluids distribution in a porous medium. Nevertheless, the original water-wetness can be modified by the petroleum`s natural surfactants (asphaltenes and resins) adsorption onto the rock surface. This adsorption may reduce petroleum recovery. In this study, the adsorption of model molecules (pyridine and benzo-quinoline), of rude oil and of its heavier fractions (asphaltenes and resins) has been investigated in terms of wettability alteration for initially water-wet surfaces (glass or quartz). In this case, the dynamic Wilhelmy plate technique provides quantitative values of wetting preference to either oil or water. The results show that, at ambient conditions, adsorption depends on concentration, adsorbent/adsorbate interaction time, pH, solvent type, substrate surface, brine concentration and environment liquid phase (water or oil). However, the initial water film on the surface does not strongly influence this phenomena. (author) 222 refs.

Deleterious effects of water-soluble fraction of petroleum, diesel and gasoline on marine pejerrey Odontesthes argentinensis larvae

International Nuclear Information System (INIS)

Rodrigues, Ricardo Vieira; Miranda-Filho, Kleber Campos; Gusmao, Emeline Pereira; Moreira, Caue Bonucci; Romano, Luis Alberto; Sampaio, Luis Andre

2010-01-01

Accidental discharges and oil spills are frequent around the world. Petroleum-derived hydrocarbons are considered one of the main pollutants of aquatic ecosystem. The importance of petroleum and refined fuels is notorious because today's society depends on them. Researches related to the toxic water-soluble fraction (WSF) of petroleum and derivatives to aquatic biota are scarce. For this reason, deleterious effects of WSF of Brazilian petroleum, automotive diesel and unleaded gasoline to marine pejerrey Odontesthes argentinensis larvae were studied employing toxicity tests and histopathological examination. Each WSF was generated in a laboratory by mixing four parts of seawater with one part of pollutant by approximately 22 h. Larvae were exposed during 96 h to different concentrations of WSF of petroleum, diesel, and gasoline, plus a control. After 96 h of exposure to the different WSFs, three larvae were sampled for histopathological studies. The median lethal concentration after 96 h (LC50) of exposure for WSF of petroleum was equal to 70.68%, it was significantly higher (P < 0.05) than the values for WSF of diesel and gasoline, which were 13.46% and 5.48%, respectively. The histological examination of pejerrey larvae exposed to WSF of petroleum, diesel and gasoline after 96 h revealed a variety of lesions in the larvae. The gills, pseudobranchs and esophagus presented epithelial hyperplasia, and the liver presented dilatation of hepatic sinusoids, hepatocitomegaly, bi-nucleated and nuclear degeneration of hepatocytes, such as pyknotic nuclei. The acute toxicity of diesel and gasoline is at least fivefold higher than Brazilian petroleum. However, all toxicants induced histopathological abnormalities in pejerrey larvae. The results are of importance since much attention has been paid to large visible surfaces of petroleum spills instead of potential toxic effects of dissolved aromatic hydrocarbons, which are more available to marine biota.

Deleterious effects of water-soluble fraction of petroleum, diesel and gasoline on marine pejerrey Odontesthes argentinensis larvae

Energy Technology Data Exchange (ETDEWEB)

Rodrigues, Ricardo Vieira [Programa de Pos-Graduacao em Aquicultura, Universidade Federal do Rio Grande, Laboratorio de Piscicultura Estuarina e Marinha, CEP 96201-900, Rio Grande, RS (Brazil); Miranda-Filho, Kleber Campos, E-mail: kleber08@gmail.com [Instituto de Oceanografia, Universidade Federal do Rio Grande, Laboratorio de Piscicultura Estuarina e Marinha, CEP 96210-030, Rio Grande, RS (Brazil); Gusmao, Emeline Pereira; Moreira, Caue Bonucci [Programa de Pos-Graduacao em Aquicultura, Universidade Federal do Rio Grande, Laboratorio de Piscicultura Estuarina e Marinha, CEP 96201-900, Rio Grande, RS (Brazil); Romano, Luis Alberto; Sampaio, Luis Andre [Instituto de Oceanografia, Universidade Federal do Rio Grande, Laboratorio de Piscicultura Estuarina e Marinha, CEP 96210-030, Rio Grande, RS (Brazil)

2010-04-01

Accidental discharges and oil spills are frequent around the world. Petroleum-derived hydrocarbons are considered one of the main pollutants of aquatic ecosystem. The importance of petroleum and refined fuels is notorious because today's society depends on them. Researches related to the toxic water-soluble fraction (WSF) of petroleum and derivatives to aquatic biota are scarce. For this reason, deleterious effects of WSF of Brazilian petroleum, automotive diesel and unleaded gasoline to marine pejerrey Odontesthes argentinensis larvae were studied employing toxicity tests and histopathological examination. Each WSF was generated in a laboratory by mixing four parts of seawater with one part of pollutant by approximately 22 h. Larvae were exposed during 96 h to different concentrations of WSF of petroleum, diesel, and gasoline, plus a control. After 96 h of exposure to the different WSFs, three larvae were sampled for histopathological studies. The median lethal concentration after 96 h (LC50) of exposure for WSF of petroleum was equal to 70.68%, it was significantly higher (P < 0.05) than the values for WSF of diesel and gasoline, which were 13.46% and 5.48%, respectively. The histological examination of pejerrey larvae exposed to WSF of petroleum, diesel and gasoline after 96 h revealed a variety of lesions in the larvae. The gills, pseudobranchs and esophagus presented epithelial hyperplasia, and the liver presented dilatation of hepatic sinusoids, hepatocitomegaly, bi-nucleated and nuclear degeneration of hepatocytes, such as pyknotic nuclei. The acute toxicity of diesel and gasoline is at least fivefold higher than Brazilian petroleum. However, all toxicants induced histopathological abnormalities in pejerrey larvae. The results are of importance since much attention has been paid to large visible surfaces of petroleum spills instead of potential toxic effects of dissolved aromatic hydrocarbons, which are more available to marine biota.

Petroleum supply monthly

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-10-01

The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blends, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States.

Petroleum supply monthly, April 1994

Energy Technology Data Exchange (ETDEWEB)

1994-04-01

Data presented in the Petroleum Supply Monthly (PSM) describe the supply and disposition of petroleum products in the United States and major US geographical regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the US. The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the US.

Petroleum marketing monthly, May 1994

Energy Technology Data Exchange (ETDEWEB)

1994-05-26

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly.

Petroleum Resins: Separation, Character, and Role in Petroleum

DEFF Research Database (Denmark)

Andersen, Simon Ivar; Speight, James

2001-01-01

are precipitated, adsorbents are added to the n-pentane solutions of the resins and oils, by which process the resins are adsorbed and subsequently recovered by the use of a more polar solvent, and the oils remain in solution. The resin fraction plays an important role in the stability of petroleum and prevents...... separation of the asphaltene constituents as a separate phase. Indeed, the absence of the resin fraction (produced by a variety of methods) from the maltenes influences the ability of the de-resined maltenes to accommodate the asphaltenes either in solution or as a stable part of a colloidal system. In spite....... Suggestions are also made regarding current thoughts of the role of these constituents on the structure and stability of petroleum....

Petroleum Supply Monthly

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-02-01

The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major U.S. geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

Petroleum supply monthly, January 1994

Energy Technology Data Exchange (ETDEWEB)

1994-01-01

Data presented describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States. The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States.

Petroleum marketing monthly, July 1994

Energy Technology Data Exchange (ETDEWEB)

1994-07-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. Monthly statistics on purchases of crude oil and sales of petroleum products are presented in five sections: summary statistics; crude oil prices; prices of petroleum products; volumes of petroleum products; and prime supplier sales volumes of petroleum products for local consumption. 7 figs., 50 tabs.

Pyrolysis of petroleum residues while making use of the hydrogen potential of polymer waste; Pyrolyse von Erdoelrueckstaenden unter Nutzung des Wasserstoffpotentials von Polymerabfaellen

Energy Technology Data Exchange (ETDEWEB)

Klemens, I; Butz, T; Rahimian, I; Linde, A [Institut fuer Erdoel- und Erdgasforschung, Clausthal-Zellerfeld (Germany)

1998-09-01

The hydrogen potential contained in waste plastics is to be utilized optimally for cracking of petroleum residues. Homogeneous distribution of the plastic particles in the petroleum residue is to ensure short distances between the hydrogen donor and acceptor, a sufficently large reaction surface, and stable mixing for further processing. Apart from homogeneity, another factor of interest is the influence of mixed-in polymer particles on the colloidal stability of the petroleum residue and the physico-chemical properties of the mixtures. With a view to further processing, the mixtures were analyzed for high-temperature stability, flow characteristics, and reaction behaviour during pyrolysis. (orig.) [Deutsch] Ziel dieses Vorhabens ist es, das in den Kunststoffabfaellen vorhandene Wasserstoffpotential optimal fuer eine tiefergehende Spaltung der Erdoelrueckstaende nutzbar zu machen. Durch eine homogene Verteilung der Kunststoffpartikel im Erdoelrueckstand soll ein moeglichst kurzer Transportweg zwischen Wasserstoff-Donor und -Akkzeptor, eine ausreichend grosse Reaktionsoberflaeche und eine fuer weitere Verarbeitungsschritte notwendige stabile Mischung erreicht werden. Ebenso interessant wie die Homogenitaet solcher Gemische ist auch der Einfluss der eingemengten Polymerteilchen auf die Kolloidstabilitaet des Erdoelrueckstandes und die physikalisch-chemischen Eigenschaften der Mischungen. Im Hinblick auf eine technische Weiterverarbeitung werden die Gemische besonders auf ihre Stabilitaet bei erhoehten Temperaturen (Heisslagerstabilitaet), ihr Fliessverhalten sowie ihr Reaktionsverhalten waehrend der Pyrolyse untersucht. (orig.)

Petroleum marketing monthly, August 1994

Energy Technology Data Exchange (ETDEWEB)

1994-08-15

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product Sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly.

Petroleum marketing monthly, September 1994

Energy Technology Data Exchange (ETDEWEB)

1994-09-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum product sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly.

Petroleum marketing annual 1994

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-08-24

The Petroleum Marketing Annual (PMA) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysis, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the fob and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Annual. For this production, all estimates have been recalculated since their earlier publication in the Petroleum Marketing Monthly (PMM). These calculations made use of additional data and corrections that were received after the PMM publication date.

Petroleum marketing annual 1994

International Nuclear Information System (INIS)

1995-01-01

The Petroleum Marketing Annual (PMA) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysis, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the fob and landed cost of imported crude oil, and the refiners' acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Annual. For this production, all estimates have been recalculated since their earlier publication in the Petroleum Marketing Monthly (PMM). These calculations made use of additional data and corrections that were received after the PMM publication date

Petroleum marketing annual, 1990

International Nuclear Information System (INIS)

1991-01-01

The Petroleum Marketing Annual contains statistical data on a variety of crude oils and refined petroleum products. The publication provides statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the free-on-board and landed cost of imported crude oil, and the refiners' acquisition cost of crude oil. Sales data for motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane are presented. (VC)

Petroleum Supply Monthly, July 1990

Energy Technology Data Exchange (ETDEWEB)

1990-09-28

Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 states and the District of Columbia). The reporting universe includes those petroleum sectors in Primary Supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States.

Characterization of Petroleum Hydrocarbon Decomposing Fungi Isolated from Mangrove Rhizosphere

Directory of Open Access Journals (Sweden)

Nuni Gofar

2011-01-01

Full Text Available The research was done to obtain the isolates of soil borne fungi isolated from mangrove rhizosphere which were capable of degrading petroleum hydrocarbon compounds. The soil samples were collected from South Sumatra mangrove forest which was contaminated by petroleum. The isolates obtained were selected based on their ability to survive, to grow and to degrade polycyclic aromatic hydrocarbons in medium containing petroleum residue. There were 3 isolates of soil borne hydrocarbonoclastic fungi which were able to degrade petroleum in vitro. The 3 isolates were identified as Aspergillus fumigates, A. parasiticus, and Chrysonilia sitophila. C. sitophila was the best isolate to decrease total petroleum hydrocarbon (TPH from medium containing 5-20% petroleum residue.

Petroleum hydrocarbon residues in the marine environment of Bassein-Mumbai

International Nuclear Information System (INIS)

Chouksey, M.K.; Kadam, A.N.; Zingde, M.D.

2005-01-01

The paper reports PHc contamination in water, sediment and biota of the coastal area of Bassein-Mumbai in relation to relatively less polluted sites (Dabhol and Ratnagiri) off the west coast of India. To facilitate inter-comparison three standards have been used though the results are reported in terms of SAM (Residue of Saudi Arabian Mix crude). The concentration of PHc in water off Bassein-Mumbai varies widely (2.9-39.2 μg l -1 ) as compared to the average baseline (2.8 μgl -1 ) with higher values generally confined to creeks and estuaries. The higher concentration of PHc in the bottom water of shallow areas is attributed to the contribution from the sediment-associated petroleum residue. High concentration of PHc in the surficial sediment of inshore area Ratnagiri (107.7 ppm, dry wt) is perhaps the remnants of an oil spill that occurred in the Bombay High region on May 17, 1993. The majority of values of PHc concentration in the surficial sediment of the Bassein-Mumbai region exceed 15 ppm (dry wt) against the expected background ( -1 respectively is estimated for cores U11 and U12. Substantial increase in the concentration of PHc in sediment after 1950 in cores T8 and T10 correlates well with the establishment of refineries on the western shore of the Thane Creek in 1955-1960. A minor peak in most cores in the top 10 cm sediment probably results from biological transfer of PHc lower into the sediment by benthic organisms. Excess of PHc retained in the sediment of the Bassein-Mumbai region over the biogenic background is estimated at 40,000 t. The PHc residues (1.8-10.8 ppm, wet wt) in fish caught off Bassein-Mumbai do not suggest bioaccumulation. (author)

Petroleum marketing monthly, June 1994

Energy Technology Data Exchange (ETDEWEB)

1994-06-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. Monthly statistics on purchases of crude oil and sales of petroleum products are presented in five sections: Summary Statistics; Crude Oil Prices; Prices of Petroleum Products; Volumes of Petroleum Products; and Prime Supplier Sales Volumes of Petroleum Products for Local Consumption. The feature article is entitled ``The Second Oxygenated Gasoline Season.`` 7 figs., 50 tabs.

Petroleum supply monthly, August 1994

Energy Technology Data Exchange (ETDEWEB)

1994-08-26

Data presented in the Petroleum Supply Monthly (PSM) describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

Petroleum marketing monthly, December 1995

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-12-05

This publication provides information and statistical data on a variety of crude oils and refined petroleum products. It presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include domestic first purchase price, f.o.b. and landed cost of imported crude, and refiners` acquisition cost of crude. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane.

Evaluation of certain crop residues for carbohydrate and protein fractions by cornell net carbohydrate and protein system

Directory of Open Access Journals (Sweden)

Venkateswarulu Swarna

2015-06-01

Full Text Available Four locally available crop residues viz., jowar stover (JS, maize stover (MS, red gram straw (RGS and black gram straw (BGS were evaluated for carbohydrate and protein fractions using Cornell Net Carbohydrate and Protein (CNCP system. Lignin (% NDF was higher in legume straws as compared to cereal stovers while Non-structural carbohydrates (NSC (% DM followed the reverse trend. The carbohydrate fractions A and B1 were higher in BGS while B2 was higher in MS as compared to other crop residues. The unavailable cell wall fraction (C was higher in legume straws when compared to cereal stovers. Among protein fractions, B1 was higher in legume straws when compared to cereal stovers while B2 was higher in cereal stovers as compared to legume straws. Fraction B3 largely, bypass protein was highest in MS as compared to other crop residues. Acid detergent insoluble crude protein (ADICP (% CP or unavailable protein fraction C was lowest in MS and highest in BGS. It is concluded that MS is superior in nutritional value for feeding ruminants as compared to other crop residues.

Petroleum marketing monthly, March 1995

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-10

This report for March 1995, provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly. A glossary is included.

Petroleum marketing annual, 1991

International Nuclear Information System (INIS)

1992-08-01

The Petroleum Marketing Annual contains statistical data on a variety of crude oils and refined petroleum products. The publication provides statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the free-on-board and landed cost of imported crude oil, and the refiners' acquisition cost of crude oil. Sales data for motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane are presented. For this publication, all estimates have been recalculated since their earlier publication in the Petroleum Marketing Monthly (PMM). These calculations made use of additional data and corrections that were received after the PMM publication dates

Petroleum marketing annual 1993

International Nuclear Information System (INIS)

1995-01-01

The Petroleum Marketing Annual (PMA) contains statistical data on a variety of crude oils and refined petroleum products. The publication provides statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the free-on-board (f.o.b.) and landed cost of imported crude oil, and the refiners acquisition cost of crude oil. Sales data for motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane are presented. For this publication, all estimates have been recalculated since their earlier publication in the Petroleum Marketing Monthly (PMM). These calculations made use of additional data and corrections that were received after the PMM publication dates

Petroleum marketing annual 1993

Energy Technology Data Exchange (ETDEWEB)

1995-01-01

The Petroleum Marketing Annual (PMA) contains statistical data on a variety of crude oils and refined petroleum products. The publication provides statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the free-on-board (f.o.b.) and landed cost of imported crude oil, and the refiners acquisition cost of crude oil. Sales data for motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane are presented. For this publication, all estimates have been recalculated since their earlier publication in the Petroleum Marketing Monthly (PMM). These calculations made use of additional data and corrections that were received after the PMM publication dates.

Evaluation of genotoxic responses of Chaetoceros tenuissimus and Skeletonema costatum to water accommodated fraction of petroleum hydrocarbons as biomarker of exposure

Digital Repository Service at National Institute of Oceanography (India)

Desai, S.R.; Verlecar, X.N.; Ansari, Z.A.; Jagtap, T.G.; Sarkar, A.; Vashistha, D.; Dalal, S.G.

by water accommodated fraction of petroleum hydrocarbons was assessed in terms of the DNA integrity measured by alkaline unwinding assay. The comparative study of the growth pattern of C. tenuissimus with respect to DNA integrity and the DNA strand breaks...

Development of a General Modelling Methodology for Vacuum Residue Hydroconversion

Directory of Open Access Journals (Sweden)

Pereira de Oliveira L.

2013-11-01

Full Text Available This work concerns the development of a methodology for kinetic modelling of refining processes, and more specifically for vacuum residue conversion. The proposed approach allows to overcome the lack of molecular detail of the petroleum fractions and to simulate the transformation of the feedstock molecules into effluent molecules by means of a two-step procedure. In the first step, a synthetic mixture of molecules representing the feedstock for the process is generated via a molecular reconstruction method, termed SR-REM molecular reconstruction. In the second step, a kinetic Monte-Carlo method (kMC is used to simulate the conversion reactions on this mixture of molecules. The molecular reconstruction was applied to several petroleum residues and is illustrated for an Athabasca (Canada vacuum residue. The kinetic Monte-Carlo method is then described in detail. In order to validate this stochastic approach, a lumped deterministic model for vacuum residue conversion was simulated using Gillespie’s Stochastic Simulation Algorithm. Despite the fact that both approaches are based on very different hypotheses, the stochastic simulation algorithm simulates the conversion reactions with the same accuracy as the deterministic approach. The full-scale stochastic simulation approach using molecular-level reaction pathways provides high amounts of detail on the effluent composition and is briefly illustrated for Athabasca VR hydrocracking.

Petroleum marketing monthly, November 1993

Energy Technology Data Exchange (ETDEWEB)

1993-11-09

The Petroleum Marketing Monthly (PMM) is designed to give information and statistical data about a variety of crude oils and refined petroleum products. The publication provides statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed costs of imported crude oil, and the refiner`s acquisition cost of crude oil. Sales data for motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane are presented.

Petroleum marketing monthly, July 1993

Energy Technology Data Exchange (ETDEWEB)

1993-07-15

The Petroleum Marketing Monthly (PMM) is designed to give information and statistical data about a variety of crude oils and refined petroleum products. The publication provides statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Sales data for motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane are presented.

Petroleum marketing monthly, January 1994

Energy Technology Data Exchange (ETDEWEB)

1994-02-01

The Petroleum Marketing Monthly (PMM) is designed to give information and statistical data about a variety of crude oils and refined petroleum products. The publication provides statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Sales data for motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane are presented.

Petroleum marketing monthly, February 1994

Energy Technology Data Exchange (ETDEWEB)

1994-02-25

The Petroleum Marketing Monthly is designed to give information and statistical data about a variety of crude oils and refined petroleum products. The publication provides statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiner`s acquisition cost of crude oil. Sales data for motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane are presented.

Petroleum marketing monthly, August 1993

Energy Technology Data Exchange (ETDEWEB)

1993-08-10

The Petroleum Marketing Monthly (PMM) is designed to give information and statistical data about a variety of crude oils and refined petroleum products. The publication provides statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Sales data for motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane are presented.

Petroleum marketing monthly, April 1994

Energy Technology Data Exchange (ETDEWEB)

1994-04-12

The Petroleum Marketing Monthly (PMM) is designed to give information and statistical data about a variety of crude oils and refined petroleum products. The publication provides statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Sales data for motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane are presented.

Petroleum marketing monthly, March 1994

Energy Technology Data Exchange (ETDEWEB)

1994-03-22

The Petroleum Marketing Monthly is designed to give information and statistical data about a variety of crude oils and refined petroleum products. The publication provides statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, education institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiner`s acquisition cost of crude oil. Sales data for motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane are presented.

Petroleum marketing monthly, October 1993

Energy Technology Data Exchange (ETDEWEB)

1993-10-07

The Petroleum Marketing Monthly (PMM) is designed to give information and statistical data about a variety of crude oils and refined petroleum products. The publication provides statistics on crude oil and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase prices, the f.o b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Sales data for motor gasoline, distillates residuals, aviation fuels, kerosene, and propane are presented.

Acute toxicity of water soluble fraction of petroleum, diesel and gasoline for newly hatched larvae of marine pejerrey Odontesthes Argentinensis

Energy Technology Data Exchange (ETDEWEB)

Rodrigues, Ricardo V.; Miranda-Filho, Kleber C.; Gusmao, Emeline P.; Moreira, Caue B.; Santos, Renato A.; Oliveira, Marcelo G.; Sampaio, Luis Andre [Fundacao Universidade do Rio Grande (FURG), RS (Brazil)

2008-07-01

The hydrocarbons of petroleum are the main aquatic pollutants and can cause toxicity to aquatic organisms, however, only a few toxicological studies were already conducted with early life stages of fish. The aim of this work was to determine the toxicity (LC50-96h) of water soluble fraction (WSF) of petroleum, diesel and gasoline for newly hatched larvae of marine pejerrey Odontesthes argentinensis. During the experiments the concentrations tested were: to petroleum (5%, 10%, 25%, 50%, 75%, and 100% of), to diesel (1%, 2%, 4%, 8%, 16%, 32%, e 64% of WSF) and to gasoline (1%, 2.5%, 5%, 10%, and 20% of WSF) plus a control to each pollutant. All treatments were done with 3 repetitions and 30 larvae. During the experiments the water quality were maintained at temperature 22,5 deg C, salinity 30, pH 7.95 and dissolved oxygen approximately around 4mg/L. The petroleum presented an CL50-96h equal to 70.68% (65.73 - 76.01), while the diesel and gasoline presented the toxicity values of 13.46% (10.19-17.79) and 5.48% (4.85-6.20), respectively. The results demonstrated a higher toxicity of light fuels (diesel and gasoline) compared to heavy petroleum. (author)

Petroleum supply monthly, April 1990

Energy Technology Data Exchange (ETDEWEB)

None

1990-06-26

The Petroleum Supply Monthly (PSM) is one of a family of three publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other two publications are the Weekly Petroleum Status Report (WPSR) and the Petroleum Supply Annual (PSA). Data presented in the Petroleum Supply Monthly describe (PSM) the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in Primary Supply.'' Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: (1) the Summary Statistics and (2) the Detailed Statistics.

Modeling and simulation of a pseudo-two-phase gas-liquid column reactor for thermal hydrocracking of petroleum heavy fractions

Directory of Open Access Journals (Sweden)

E.M. Matos

2002-07-01

Full Text Available This work presents a model to predict the behavior of velocity, gas holdup and local concentration fields in a pseudo-two-phase gas-liquid column reactor applied for thermal hydrocracking of petroleum heavy fractions. The model is based on the momentum and mass balances for the system, using an Eulerian-Eulerian approach. Using the k-epsilon model,fluid dynamics accounts for both laminar and turbulent flows, with discrete small bubbles (hydrogen flowing in a continuous pseudohomogeneous liquid phase (oil and catalyst particles. The petroleum is assumed to be a mixture of pseudocomponents, grouped by similar chemical structural properties, and the thermal hydrocracking is taken into account using a kinetic network based on these pseudocomponents.

Développements récents dans le domaine de l'hydrotraitement des fractions lourdes Advances in the Hydrotreatment of Heavy Petroleum Feedstocks

Directory of Open Access Journals (Sweden)

Jacquin Y.

2006-11-01

Full Text Available L'évolution du raffinage vers une utilisation des produits pétroliers pour les usages des transports et comme base pour la pétrochimie renforce l'intérêt pour les procédés de transformation des fractions lourdes du pétrole en fractions légères correspondant au marché actuel. Les problèmes posés par le raffinage des résidus de distillation sont semblables à ceux rencontrés pour le traitement des bruts lourds non conventionnels. Les méthodes qui sont actuellement envisagées peuvent être classées en 2 catégories : les méthodes de raffinage avec rejet de carbone comme la cokéfaction et le désasphaltage et les méthodes sans rejet de carbone comme la viscoréduction, l'hydroviscoréduction et l'hydrotraitement catalytique. Chacune de ces techniques est examinée en précisant les rendements en produits liquides qu'elle permet d'atteindre et les hydrotraitements complémentaires nécessaires pour obtenir des produits répondant aux spécifications du marché des produits pétroliers. Les progrès réalisés dans la conception des catalyseurs utilisés pour le traitement des produits lourds permet aujourd'hui d'envisager l'hydrotraitement direct des résidus sous vide de la majorité des bruts raffinés. The increasing use of refined petroleum products for transportation purposes and as petrochemical bases reinforces interest in processes for converting heavy fractions into light fractions suitable for today's market. The refining of distillation residues involves difficulties similar to unconventional heavy-crude processing. As of now methods may be classified in two categories: (i refining methods with carbon rejection such as coking and deasphalting processes, and (ii methods without carbon rejection such as visbreaking, hydrovisbreaking and catalytic hydrotreating. Each of these techniques is examined, taking into account the liquid-product yields it may reach, and the additional hydrotreatments necessary to meet market

Carbon fractions and soil fertility affected by tillage and sugarcane residue management an Xanthic Udult

Directory of Open Access Journals (Sweden)

Iara Maria Lopes

2017-10-01

Full Text Available The gradual change in management practices in sugarcane (Saccharum spp. production from burning straw to a green harvesting system, as well as the use of minimum soil tillage during field renovation, may affect soil fertility and soil organic matter (SOM contents. The objectives of this work were to investigate the influence of sugar cane production systems on: (1 soil fertility parameters; (2 on physical carbon fractions; (3 and on humic substance fractions, in a long-term experiment, comparing two soil tillage and two residue management systems an Xanthic Udult, in the coastal tableland region of Espírito Santo State, Brazil. The treatments consisted of plots (conventional tillage (CT or minimum tillage (MT and subplots (residue burned or unburned at harvesting, with five replicates The highest values of Ca2+ + Mg2+ and total organic carbon (TOC were observed in the MT system in all soil layers, while high values of K+ were observed in the 0.1-0.2 m layer. The CT associated with the burned residue management negatively influenced the TOC values, especially in the 0.1-0.2 and 0.2-0.4 m layers. The carbon in the humin fraction and organic matter associated with minerals were significantly different among the tillage systems; the MT showed higher values than the CT. However, there were no significant differences between the sugarcane residue management treatments. Overall, fractioning the SOM allowed for a better understanding of tillage and residue management systems effects on the soil properties.

Petroleum supply monthly, January 1996

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-02-15

The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

Petroleum supply monthly, October 1993

Energy Technology Data Exchange (ETDEWEB)

1993-10-26

The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

Petroleum Supply Monthly, August 1990

Energy Technology Data Exchange (ETDEWEB)

1990-10-30

The Petroleum Supply Monthly (PSM) is one of a family of three publications produced by the Petroleum Supply Division within the Energy Information administration (EIA) reflecting different levels of data timeliness and completeness. The other two publications are the Weekly Petroleum Status Report (WPSR) and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) district movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in Primary Supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections (1) the Summary Statistics and (2) the Detailed Statistics.

Petroleum supply monthly, September 1991

Energy Technology Data Exchange (ETDEWEB)

1991-09-30

The Petroleum Supply Monthly (PSM) is one of a family of three publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other two publications are the Weekly Petroleum Status Report (WPSR) and the Petroleum Supply Annual (PSA). Data presented in PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administrations for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 states and the District of Columbia). The reporting universe includes those petroleum sectors in Primary Supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections (1) the Summary Statistics and (2) the Detailed Statistics. 65 tabs.

Petroleum marketing monthly, August 1990

Energy Technology Data Exchange (ETDEWEB)

1990-11-07

The Petroleum Marketing Monthly (PMM) is designed to give information and statistical data about a variety of crude oils and refined petroleum products. The publication provides statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners' acquisition cost of crude oil. Sales data for motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane are presented. 12 figs., 49 tabs.

GC/MS determination of bicyclic sesquiterpanes in crude oils and petroleum products

International Nuclear Information System (INIS)

Yang, C.; Wang, Z.; Hollebone, B.; Brown, C.E.; Landriault, M.

2008-01-01

A study was conducted in which sesquiterpanes, a component of crude oils and petroleum products, were identified and characterized in an effort to determine the feasibility of using them as biomarkers for fingerprinting and identifying unknown lighter petroleum product spills. The study compared the distributions of sesquiterpanes in different oils, oil distillation fractions and refined products, including light and mid-range distillate fuels, residual fuels and lubricating oils. Evaporative weathering effects on sesquiterpane distribution and concentration were quantitatively studied and several diagnostic indices of sesquiterpane were developed for oil correlation and differentiation. Bicyclic sesquiterpanes in crude oils and oil products have much different abundances and distributions. Therefore, the relevant sesquiterpane ratios are different. Bicyclic sesquiterpanes are mostly partitioned into the medium distillation fractions. The study showed that concentrations of sesquiterpanes in crude oil and diesel fuel increase in proportion with the increase of weathering percentages. Relevant diagnostic ratios therefore remained stable. It was concluded that C 15 and C 16 sesquiterpanes may be alternative internal tracers to provide a direct way to estimate the depletion of oils, particularly diesels, in oil spill investigations. 13 refs., 6 tabs., 4 figs

Converting petroleum into acids, soaps, etc

Energy Technology Data Exchange (ETDEWEB)

Imray, J

1883-06-19

The conversion of petroleum and hydrocarbons resulting from distillation of lignite, coal, peat, shale, etc., into organic acids by treating the hydrocarbons in the presence of caustic alkalies, alkaline earths, alkaline carbonates, or other bodies with alkaline reaction, with a current of air or oxygen, with or without pressure, at a raised temperature, and decomposing the soaps formed, the free acid being removed from the compound which is then separated into single fractions by fractional distillation or by taking advantage of the unequal solubility in petroleum or similar solvents is described.

Effects of operating conditions on compositional characteristics and reaction kinetics of liquid derived by delayed coking of nigerian petroleum residue

Directory of Open Access Journals (Sweden)

O. O. Bello

2006-09-01

Full Text Available The thermal upgrading of Nigerian petroleum residue was studied at relatively low pressure in a delayed coking reactor system. In this work, the intent was to investigate the effects of process variables such as reaction temperature (200(0C to 600(0C, reaction time (0 to 120min, additive concentration loading and additive-to-residue ratio on the amounts and quality of organic liquid product (OLP. The liquid products derived from the delayed coking process were characterized by means of instrumental analysis of gas-liquid chromatography. Results obtained from the analyses of the OLP revealed an upward trend of the conversion process and the selectivity of the aromatic compounds with additive-to-residue ratio (ARR and increase in temperature. This led to maximum yield of 37.2% achieved with ARR of 5 compared to 31% achieved with ordinary thermal conversion. The selectivity for aromatic hydrocarbons was maximum at 83.1wt% the selectivity towards aromatics and aliphatic hydrocarbons were highest for methanol-potassium hydroxide and methanol respectively. In all additive system cases, maximum OLP was produced at an optimum reaction temperature of 370(0C in the delayed coking reactor and at higher residence time. The gaseous product consisted of carbon monoxide and carbon dioxide and C1 - C6 hydrocarbons, which amounted to about 20 to 30 wt% of liquid distillate. The information obtained in this study show that the organic liquid products are amenable to characterization procedure and provided the basis for the identification of processes for upgrading Nigerian petroleum residue and such other starting materials such as bitumen or fossil fuel coal liquids.

Metallic elements fractionation in municipal solid waste incineration residues

Science.gov (United States)

Kowalski, Piotr R.; Kasina, Monika; Michalik, Marek

2016-04-01

Municipal solid waste incineration (MSWI) residues are represented by three main materials: bottom ash, fly ash and air pollution control (APC) residues. Among them ˜80 wt% is bottom ash. All of that materials are products of high temperature (>1000° C) treatment of waste. Incineration process allows to obtain significant reduction of waste mass (up to 70%) and volume (up to 90%) what is commonly used in waste management to reduce the amount need to be landfilled or managed in other way. Incineration promote accumulation non-combustible fraction of waste, which part are metallic elements. That type of concentration is object of concerns about the incineration residues impact on the environment and also gives the possibility of attempts to recover them. Metallic elements are not equally distributed among the materials. Several factors influence the process: melting points, volatility and place and forms of metallic occurrence in the incinerated waste. To investigate metallic elements distribution in MSWI residues samples from one of the biggest MSW incineration plant in Poland were collected in 2015. Chemical analysis with emphasis on the metallic elements content were performed using inductively coupled plasma optical emission (ICP-OES) and mass spectrometry (ICP-MS). The bottom ash was a SiO2-CaO-Al2O3-Fe2O3-Na2O rich material, whereas fly ash and APC residues were mostly composed of CaO and SiO2. All of the materials were rich in amorphous phase occurring together with various, mostly silicate crystalline phases. In a mass of bottom ash 11 wt% were metallic elements but also in ashes 8.5 wt% (fly ash) and ˜4.5 wt% (APC residues) of them were present. Among the metallic elements equal distribution between bottom and fly ash was observed for Al (˜3.85 wt%), Mn (770 ppm) and Ni (˜65 ppm). In bottom ash Fe (5.5 wt%), Cr (590 ppm) and Cu (1250 ppm) were concentrated. These values in comparison to fly ash were 5-fold higher for Fe, 3-fold for Cu and 1.5-fold for

Petroleum Supply Monthly, September 1990. [Contains glossary

Energy Technology Data Exchange (ETDEWEB)

Whited, D.; Jacobus, P. (eds.)

1990-11-28

Data presented in this PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in Primary Supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. 12 figs., 46 tabs.

Petroleum supply monthly, October 1990. [Contains Glossary

Energy Technology Data Exchange (ETDEWEB)

1990-12-27

Data presented in this report describes the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in Primary Supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. 12 figs., 54 tabs.

Petroleum marketing monthly with data for January 1998

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-04-01

This publication provides information and statistical data on a variety of crude oils and refined petroleum products. Statistics on crude oil costs and refined petroleum products sales are presented. Data on crude oil include the domestic purchase price, the free on board and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. Monthly statistics on purchases of crude oils and sales of petroleum products are presented in five sections: (1) summary statistics, (2) crude oil prices, (3) prices of petroleum products, (4) volumes of petroleum products, and (5) prime supplier sales volumes of petroleum products for local consumption. 50 tabs.

Physico-chemical characterisation of material fractions in residual and source-segregated household waste in Denmark

DEFF Research Database (Denmark)

Götze, Ramona; Pivnenko, Kostyantyn; Boldrin, Alessio

2016-01-01

differences in the physico-chemical properties of residual and source-segregated waste fractions were found for many parameters related to organic matter, but also for elements of environmental concern. Considerable differences in potentially toxic metal concentrations between the individual recyclable......Physico-chemical waste composition data are paramount for the assessment and planning of waste management systems. However, the applicability of data is limited by the regional, temporal and technical scope of waste characterisation studies. As Danish and European legislation aims for higher...... recycling rates evaluation of source-segregation and recycling chains gain importance. This paper provides a consistent up-to-date dataset for 74 physico-chemical parameters in 49 material fractions from residual and 24 material fractions from source-segregated Danish household waste. Significant...

Petroleum hydrocarbon concentrations in eight mollusc species along Tamilnadu coast, Bay of Bengal, India.

Science.gov (United States)

Veerasingam, S; Venkatachalapathy, R; Sudhakar, S; Raja, P; Rajeswari, V

2011-01-01

Eight mollusc species and sediment samples collected from three different stations along Tamilnadu coast, Bay of Bengal, India were analysed for the levels of petroleum hydrocarbons to elucidate the status of the petroleum residues in mollusc meant for human consumption. The concentrations of petroleum hydrocarbons in sediments along Tamilnadu coast varied from 5.04-25.5 microg/g dw (dry weight). High concentration of petroleum hydrocarbons in the sediment of Uppanar estuary (25.5 +/- 1.45 microg/g dw) was perhaps land and marine based anthropogenic sources of this region. The petroleum hydrocarbon residues in eight mollusc species collected from Uppanar, Vellar and Coleroon estuaries varied between 2.44-6.04 microg/g ww (wet weight). Although the concentration of petroleum hydrocarbons in sediment of the Uppanar region was markedly higher than the background, the petroleum hydrocarbon residues in mollusc collected from Uppanar estuary did not suggest bioaccumulation. The results signified that industrial growth has affected the aquatic environments and regular monitoring will help to adopt stringent pollution control measures for better management of the aquatic region.

Petroleum marketing monthly with data for April 1995

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-07-05

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data on the Petroleum Marketing Monthly. Monthly statistics on purchases of crude oil and sales of petroleum products are presented in the Petroleum Marketing Monthly in five sections: Summary statistics; crude oil prices; prices of petroleum products; volumes of petroleum products; and prime supplier sales volumes of petroleum products for local consumption.

Petroleum marketing monthly with data for May 1997

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-08-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly.

Petroleum marketing monthly with data for September 1997

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures and accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly.

Petroleum Marketing Annual, 1989

Energy Technology Data Exchange (ETDEWEB)

1990-12-18

This report contains statistical data on a variety of crude oils and refined petroleum products. The publication provides statistics on crude oil costs and refined petroleum products sales for us by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the free-on-board (f.o.b.) and landed cost of imported crude oil, and the refiners' acquisition cost of crude oil. Sales data for motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane are presented. 13 figs., 51 tabs.

Petroleum supply monthly, October 1991. [Contains glossary

Energy Technology Data Exchange (ETDEWEB)

1991-10-30

Data presented in this report describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in Primary Supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importer, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data are divided into two sections (1) the Summary Statistics and (2) the Detailed Statistics 14 figs., 56 tabs.

Ultrasonic measurements on residual stress in autofrettged thick walled petroleum pipes

International Nuclear Information System (INIS)

Woias, G.; Mizera, J.

2008-01-01

The residual stresses in a component or structure are caused by incompatible permanent deformation and related gradient of plastic/elastic strains. They may be generated or modified at every stage in the components life cycle, from original material production to final disposal. Residual stresses can be measured by non-destructive techniques, including X-ray and neutron diffraction, magnetic and ultrasonic methods. The selection of the optimum measurement technique should take account volumetric resolution, material, geometry and access to the component. For large metallic components neutron diffraction is of prime importance as it provides quantitative information on stresses in relatively large volume of methods disregarding its shape complexity. Residual stresses can play a significant role in explaining or preventing failure of components of industrial installations. One example of residual stresses preventing failure are the ones generated by shot peening, inducing surface compressive stresses that improve the fatigue life. Petroleum refinery piping is generally characterized by large-diameters, operated at elevated temperature and under high pressure. Pipelines of a polyethylene plant working in one of the Polish refineries are subjected to pressures exceeding 300 MPa at temperatures above 200 o C. The pipes considered here were pressurized with pressure of 600 MPa. The wall thickness of the pipes is 27 mm and pipe dimensions are 46 x 100 mm. The material is steel with Re=580 MPa. Due to pressurizing, the components retain compressive stresses at the internal surface. These stresses increase resistance to cracking of the pipes. Over the period of exploitation these stresses diminish due to temperature activated relaxation or creep. The purpose of the project is to verify kinetics of such a relaxation process and calibrate alternative methods of their measurements. To avoid stress relaxation, numerical analysis from Finite Element Modelling (FEM)gave an

Petroleum marketing monthly with data for October 1996

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-01-01

This publication presents statistical data on crude oil costs and refined petroleum products sales. Data on petroleum include the domestic first purchase price, landed cost of imported crude oil, and the refiner`s acquisition cost of crude oil. Sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane.

Petroleum exclusion under CERCLA: A defense to liability

International Nuclear Information System (INIS)

Landreth, L.W.

1991-01-01

When CERCLA was originally passed in 1980, the petroleum industry lobbied successfully to exclude the term open-quotes petroleumclose quotes from the definition of a CERCLA section 101 (14) hazardous substance. Under CERCLA section 101 (33), petroleum is also excluded from the definition of a open-quotes pollutant or contaminant.close quotes Exclusion from the designation as a defined hazardous substance has provided a defense to liability under CERCLA section 107 when the release of petroleum occurs. The scope of the petroleum exclusion under CERCLA has been a critical and recurring issue arising in the context of Superfund response activities. Specifically, oil that is contaminated by hazardous substances during the refining process is considered open-quotes petroleumclose quotes under CERCLA and thus excluded from CERCLA response authority and liability unless specifically listed under RCRA or some other statute. The U.S. EPAs position is that contaminants present in used oil, or any other petroleum substance, do not fall within the petroleum exclusion. open-quotes Contaminants,close quotes as discussed here, are substances not normally found in refined petroleum fractions or present at levels which exceed those normally found in such fractions. If these contaminants are CERCLA hazardous substances, they are subject to CERCLA response authority and liability. This paper discusses the parameters of the CERCLA open-quotes Petroleum Exclusion.close quotes It briefly examines selected state laws, RCRA, the Clean Water Act (CWA) and the Safe Drinking Water Act (SDWA) for treatment of petroleum and petroleum products. And, finally, this paper discusses new legislation regarding oil pollution liability and compensation

Petroleum hydrocarbon concentration in sediments along northern west coast of India

Digital Repository Service at National Institute of Oceanography (India)

Ram, A.; Kadam, A.N.

Gas chromatography revealed that nonpolar material extracted from surface sediments collected along the northern west coast of India was originated from petroleum hydrocarbon residue. Petroleum hydrocarbon levels as determinEd. by fluorescence...

Petroleum marketing monthly, November 1991. [Contains glossary

Energy Technology Data Exchange (ETDEWEB)

1991-11-07

The Petroleum Marketing Monthly is designed to give information and statistical data about a variety of crude oils and refined petroleum products. The publication provides statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners' acquisition cost of crude oil. Sales data for motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane are presented. 12 figs., 53 tabs.

Characterization of crude oils and petroleum products: (I Elution liquid chromatographic separation and gas chromatographic analysis of crude oils and petroleum products

Directory of Open Access Journals (Sweden)

E.O. Odebunmi

2002-12-01

Full Text Available Some physical and chemical properties of samples of light, medium and heavy Nigerian crude oils and petroleum products including gasoline, kerosene and engine oil have been measured and are reported in this paper. The crude oils and petroleum products have also been characterized by fractional distillation and elution liquid chromatography. The fractions obtained from elution liquid chromatography were analyzed using gas chromatography (GC. The GC fractions were identified by comparing the retention time of peaks in the unknown samples with those of components of calibration standard mixtures. The importance of the physico-chemical properties and the significance of the fractional distillation and chromatographic separation methods to industrial process operations have been discussed.

Production of petroleum bitumen by oxidation of heavy oil residue with sulfur

Science.gov (United States)

Tileuberdi, Ye.; Akkazyn, Ye. A.; Ongarbayev, Ye. K.; Imanbayev, Ye. I.; Mansurov, Z. A.

2018-03-01

In this paper production of bitumen adding elemental sulfur at oxidation of oil residue are investigated. The objects of research were distilled residue of Karazhanbas crude oil and elemental sulfur. These oil residue characterized by a low output of easy fractions and the high content of tar-asphaltene substances, therefore is the most comprehensible feedstock for producing bitumen. The sulfur is one of the oil product collected in oil extraction regions. Oxidation process of hydrocarbons carried out at temperatures from 180 up to 210 °С without addition of sulfur and with the addition of sulfur (5-10 wt. %) for 4 hours. At 200 °С oxidation of hydrocarbons with 5, 7 and 10 wt.% sulfur within 3-4 h allows receiving paving bitumen on the mark BND 200/300, BND 130/200, BN 90/130 and BN 70/30. Physical and mechanical characteristics of oxidation products with the addition of 5-7 wt. % sulfur corresponds to grade of paving bitumen BND 40/60. At the given temperature oxidized for 2.5-3 h, addition of 10 wt. % sulfur gave the products of oxidation describing on parameters of construction grades of bitumen (BN 90/10).

The use of nuclear energy for obtaining petroleum

International Nuclear Information System (INIS)

Waldmann, H.; Koch, C.; Thelen, H.J.; Kappe, P.

1982-01-01

After some basic considerations of petroleum demand, petroleum supply and petroleum reserves, the article gives a survey of the various methods of obtaining petroleum. The use of energy in the form of steam and electricity in the previously used processes and in conventional deposits requires up to 50% of the energy contained in the oil obtained. Now unconventional sources of petroleum (tertiary petroleum, heavy fractions and shale oil) could become of interest to West Germany in the near future. The economy of production can be determined by the energy source used, to a large extent. A series of possibilities are discussed for using nuclear steam raising systems for this purpose. (UA) [de

Shale oil. I. Genesis of oil shales and its relation to petroleum and other fuels

Energy Technology Data Exchange (ETDEWEB)

McKee, R H; Manning, P D.V.

1927-01-01

Oil-shale kerogen originated from resinous vegetation residues of past eras, whereas well petroleum was formed from oil shales by pressure and mild heat. Petroleum migrated to its present reservoir from neighboring oil-shale deposits, leaving a residue of black bituminous shales. The high carbon dioxide content of gases present in petroleum wells originated from kerogen, as it gives off carbon dioxide gas before producing soluble oil or bitumen.

Petroleum supply monthly with data from January 1998

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States.

Petroleum supply monthly with data for March 1997

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-05-01

The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration reflecting different levels of data timeliness and completeness. Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major U.S. geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 states and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States.

Bacterial Utilization of Petroleum in Liquid and Simulated Soil ...

African Journals Online (AJOL)

... by the weight of extracted residual oil indicated that the extents of oil removal in the stimulated and/or bioaugmented soils were significantly high in relation to unsupplemented and uninoculated controls. Keywords: Bacterial utilization, Petroleum in liquid, Petroleum in soil, Environments Bio-Research Vol. 6 (2) 2008: pp.

PGPR enhanced phytoremediation of petroleum contaminated soil and rhizosphere microbial community response.

Science.gov (United States)

Hou, Jinyu; Liu, Wuxing; Wang, Beibei; Wang, Qingling; Luo, Yongming; Franks, Ashley E

2015-11-01

The aim of this study was to investigate petroleum phytoremediation enhancement by plant growth promoting bacteria (PGPR), specifically the correlation between petroleum hydrocarbon fractions and bacterial community structure affected by remediation and PGPR inocula. Aged petroleum contaminated soil was remediated by tall fescue (Testuca arundinacea L.) inoculated with two PGPR strains. Hydrocarbon degradation was measured by GC-MS (Gas-chromatography Mass-spectrometer) based on carbon fraction numbers (C8-C34). Changes in bacterial community structure were analyzed by high-throughput pyrosequencing of 16s rRNA. PGPR inoculation increased tall fescue biomass and petroleum hydrocarbons were removed in all the treatments. Maximum hydrocarbon removal, particular high molecular weight (C21-C34) aliphatic hydrocarbons (AHs) and polycyclic aromatic hydrocarbons (PAHs), was observed in tall fescue inoculated with PGPR. The relative abundance of phyla γ-proteobacteria and Bacteroidetes increased after different treatments compared with controls. Moreover, a bacterial guild mainly comprising the genera Lysobacter, Pseudoxanthomonas, Planctomyces, Nocardioides, Hydrogenophaga, Ohtaekwangia was found to be positively correlated with C21-C34 petroleum hydrocarbons fractions removal by RDA analysis, implying that petroleum degradation was unrelated to bacterial community diversity but positively correlated with specific petroleum degraders and biosurfactant producers. Copyright © 2015 Elsevier Ltd. All rights reserved.

Catalysts in petroleum refining and petrochemical industries 1995

Energy Technology Data Exchange (ETDEWEB)

Absi-Halabi, M.; Beshara, J.; Qabazard, H.; Stanislaus, A. [eds.] [Petroleum, Petrochemicals and Materials Division, Kuwait Institute of Scientific Research, Kuwait (Kuwait)

1996-07-01

Catalysis plays an increasingly critical role in modern petroleum refining and basic petrochemical industries. The market demands for and specifications of petroleum and petrochemical products are continuously changing. They have impacted the industry significantly over the past twenty years. Numerous new refining processes have been developed and significant improvements were made on existing technologies. Catalysts have been instrumental in enabling the industry to meet the continuous challenges posed by the market. As we enter the 21st century, new challenges for catalysis science and technology are anticipated in almost every field. Particularly, better utilization of petroleum resources and demands for cleaner transportation fuels are major items on the agenda. It is against this background that the 2nd International Conference on Catalysts in Petroleum Refining and Petrochemical Industries was organized. The papers from the conference were carefully selected from around 100 submissions. They were a mix of reviews providing an overview of selected areas, original fundamental research results, and industrial experiences. The papers in the proceedings were grouped in the following sections for quick reference: Plenary Papers; Hydroprocessing of Petroleum Residues and Distillates; Fluid Catalytic Cracking; Oxidation Catalysis; Aromatization and Polymerization Catalysis; Catalyst Characterization and Performance. The plenary papers were mostly reviews covering important topics related to the objectives of the conference. The remaining sections cover various topics of major impact on modern petroleum refining and petrochemical industries. A large number of papers dealt with hydroprocessing of petroleum distillates and residues which reflects the concern over meeting future sulfur-level specifications for diesel and fuel oils

Petroleum marketing monthly, September 1993

Energy Technology Data Exchange (ETDEWEB)

1993-09-14

This document designed to give information and statistical data about a variety of crude oils and refined petroleum products. The publication provides statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and for the refiners` acquisition cost of crude oil. Sales data for motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane are presented.

Petroleum marketing monthly, June 1993

Energy Technology Data Exchange (ETDEWEB)

1993-06-10

This publication is designed to give information and statistical data about a variety of crude oils and refined petroleum products. The publication provides statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Sales data for motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane are presented.

Petroleum Marketing Monthly, January 1991. [Contains Glossary

Energy Technology Data Exchange (ETDEWEB)

1991-01-09

The Petroleum Marketing Monthly (PMM) is designed to give information and statistical data about a variety of crude oils and refined petroleum products. The publication provides statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners' acquisition cost of crude oil. Sales data for motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane are presented. 12 figs., 55 tabs.

Industrial, agricultural, and petroleum contaminants in cormorants wintering near the Houston Ship Channel, Texas, USA

Science.gov (United States)

King, K.A.; Stafford, C.J.; Cain, B.W.; Mueller, A.J.; Hall, H.D.

1987-01-01

Double-crested cormorants (Phalacrocorax auritus ) collected in the Houston Ship Channel, Texas, USA, in November shortly after their fall migration contained residues of several industrial, agricultural, and petroleum contaminants including polychlorinated styrenes (PCS's), polychlorinated biphenyls (PCB's), DDE, and petroleum hydrocarbons. PCS concentrations in over-wintering birds collected in late February were three times higher than those in birds collected in November. PCB and petroleum concentrations remained at about the same level throughout the 3-month winter period. Petroleum hydrocarbons were present in all cormorants and residues in some individuals exceeded 25 ppm (wet weight). Mean DDE residues in samples collected in November and February were less than 1 ppm. Low concentrations of five other organochlorine compounds, not detected in cormorants collected in November, were recovered in birds collected in February.

Petroleum supply monthly - with data for May 1996

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-07-01

The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major U.S. geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. This document contains a glossary.

Petroleum supply monthly with data from April 1996

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-06-01

The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major U.S. geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States.

Petroleum marketing monthly, January 1996 with data for October 1995

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-01-04

The Petroleum Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane.

Petroleum marketing monthly, May 1999, with data for February 1999

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-05-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. Monthly statistics on purchases of crude oil and sales of petroleum products are presented in the Petroleum Marketing Monthly in five sections: Initial Estimates; Summary Statistics; Crude Oil Prices; Prices of Petroleum Products; Volumes of Petroleum Products; and Prime Supplier Sales Volumes of Petroleum Products for Local Consumption. 7 figs., 50 tabs.

Petroleum marketing monthly, May 1998, with data for February 1998

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-05-01

The Petroleum Marketing Monthly (PMM) provides Information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. Monthly statistics on purchases of crude oil and sales of petroleum products are presented in the Petroleum Marketing Monthly in five sections: summary statistics; crude oil prices; prices of petroleum products; volumes of petroleum products; prime supplier sales volumes of petroleum products for local consumption. 7 figs., 50 tabs.

Petroleum marketing monthly, July 1998 with data for April 1998

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-07-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. Monthly statistics on purchases of crude oil and sales of petroleum products are presented in the Petroleum Marketing Monthly in five sections: summary statistics; crude oil prices; prices of petroleum products; volumes of petroleum products; and prime supplier sales volumes of petroleum products for local consumption. 7 figs., 50 tabs.

Petroleum marketing monthly: August 1998, with data for May 1998

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-08-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. Monthly statistics on purchases of crude oil and sales of petroleum products are presented in the Petroleum Marketing Monthly in five sections: Summary Statistics; Crude Oil Prices; Prices of Petroleum Products; Volumes of Petroleum Products; and Prime Supplier Sales Volumes of Petroleum Products for Local Consumption. 7 figs., 50 tabs.

Petroleum marketing monthly, September 1998, with data for June 1998

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-09-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. Monthly statistics on purchases of crude oil and sales of petroleum products are presented in the Petroleum Marketing Monthly in five sections: summary statistics; crude oil prices; prices of petroleum products; volumes of petroleum products; prime supplier sales volumes of petroleum products for local consumption. 7 figs., 50 tabs.

Petroleum marketing monthly, December 1998 with data for September 1998

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-12-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. Monthly statistics on purchases of crude oil and sales of petroleum products are presented in the Petroleum Marketing Monthly in five sections: summary statistics; crude oil prices; prices of petroleum products; volumes of petroleum products; and prime supplier sales volumes of petroleum products for local consumption. 7 figs., 50 tabs.

Petroleum marketing monthly, June 1999, with data for March 1999

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-06-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. Monthly statistics on purchases of crude oil and sales of petroleum products are presented in the Petroleum Marketing Monthly in five sections: Initial Estimates; Summary Statistics; Crude Oil Prices; Prices of Petroleum Products; Volumes of Petroleum Products; and Prime Supplier Sales Volumes of Petroleum Products for Local Consumption. 7 figs., 50 tabs.

Petroleum marketing monthly, January 1999 with data for October 1998

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-01-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. Monthly statistics on purchases of crude oil and sales of petroleum products are presented in the Petroleum Marketing Monthly in five sections: summary statistics; crude oil prices; prices of petroleum products; volumes of petroleum products; and prime supplier sales volumes of petroleum products for local consumption. 7 figs., 50 tabs.

Petroleum marketing monthly, July 1999, with data for April 1999

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-07-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. Monthly statistics on purchases of crude oil and sales of petroleum products are presented in the Petroleum Marketing Monthly in five sections: initial estimates; summary statistics; crude oil prices; prices of petroleum products; volumes of petroleum products; and prime supplier sales volumes of petroleum products for local consumption. 7 figs., 70 tabs.

Petroleum marketing monthly, November 1998, with data for August 1998

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-11-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. Monthly statistics on purchases of crude oil and sales of petroleum products are presented in the Petroleum Marketing Monthly in five sections: Summary statistics; Crude oil prices; Prices of petroleum products; Volumes of petroleum products; and Prime supplier sales volumes of petroleum products for local consumption. 7 figs., 50 tabs.

Petroleum marketing monthly, October 1998, with data for July 1998

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-10-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. Monthly statistics on purchases of crude oil and sales of petroleum products are presented in the Petroleum Marketing Monthly in five sections: Summary statistics; Crude oil prices; Prices of petroleum products; Volumes of petroleum products; and Prime supplier sales volumes of petroleum products for local consumption. 7 figs., 50 tabs.

Petroleum marketing monthly, June 1998, with data from March 1998

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-06-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. Monthly statistics on purchases of crude oil and sales of petroleum products are presented in the Petroleum Marketing Monthly in five sections: summary statistics; crude oil prices; prices of petroleum products; volumes of petroleum products and prime supplier sales volumes of petroleum products for local consumption. 7 figs., 50 tabs.

Petroleum marketing monthly, March 1999 with data for December 1998

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. Monthly statistics on purchases of crude oil and sales of petroleum products are presented in the Petroleum Marketing Monthly in five sections: summary statistics; crude oil prices; prices of petroleum products; volumes of petroleum products; and prime supplier sales volumes of petroleum products for local consumption. 7 figs., 50 tabs.

Petroleum marketing monthly, February 1999 with data for November 1998

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-02-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. Monthly statistics on purchases of crude oil and sales of petroleum products are presented in the Petroleum Marketing Monthly in six sections: Initial Estimates; Summary Statistics; Crude Oil Prices; Prices of Petroleum Products; Volumes of Petroleum Products; and Prime Supplier Sales Volumes of Petroleum Products for Local Consumption. 7 figs., 50 tabs.

Petroleum marketing monthly, June 1995 with data for March 1995

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-06-16

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly. Monthly statistics on purchases of crude oil and sales of petroleum products are presented in the Petroleum Marketing Monthly in five sections: Summary Statistics Crude Oil Prices; Prices of Petroleum Products; Volumes of Petroleum Products; and Prime Supplier Sales Volumes of Petroleum Products for Local Consumption.

Petroleum marketing monthly, June 1996: With data for March 1996

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-06-04

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o. b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly.

Petroleum marketing monthly, May 1996 with data for February 1996

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-05-02

The Petroleum Marketing Monthly provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly.

Petroleum marketing monthly, May 1995 with data for February 1995

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-05-09

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly.

Petroleum marketing monthly, April 1999, with data for January 1999

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-04-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly. 56 tabs.

Petroleum marketing monthly, October 1995 with data for July 1995

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-10-03

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost Of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly.

Petroleum marketing monthly, September 1995 with data for June 1995

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-08-31

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the fob and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly.

Petroleum marketing monthly, June 1997 with data for March 1997

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-06-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. 7 figs., 50 tabs.

Petroleum marketing monthly, March 1998, with data for December 1997

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. 7 figs., 50 tabs.

Petroleum marketing monthly, September 1997 with data for June 1997

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-09-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. 7 figs., 50 tabs.

Petroleum marketing monthly, January 1998 with data for October 1997

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-01-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. 7 figs., 50 tabs.

Petroleum marketing monthly, April 1996 with data for January 1996

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-04-02

The Petroleum Marketing Monthly provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane.

Petroleum marketing monthly, March 1996 with data for December 1995

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-08

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane.

Petroleum marketing monthly, May 1997 with data for February 1997

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-05-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. 7 figs., 50 tabs.

Petroleum marketing monthly, November 1997 with data for August 1997

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-11-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. 7 figs., 50 tabs.

Petroleum marketing monthly, April 1997 with data for January 1997

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-04-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. 7 figs., 50 tabs.

Petroleum marketing monthly, February 1997 with data for November 1996

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-02-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. 7 figs., 50 tabs.

Petroleum marketing monthly, October 1997 with data for July 1997

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-10-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. 7 figs., 50 tabs.

A new procedure for the determination of distillation temperature distribution of high-boiling petroleum products and fractions.

Science.gov (United States)

Boczkaj, Grzegorz; Przyjazny, Andrzej; Kamiński, Marian

2011-03-01

The distribution of distillation temperatures of liquid and semi-fluid products, including petroleum fractions and products, is an important process and practical parameter. It provides information on properties of crude oil and content of particular fractions, classified on the basis of their boiling points, as well as the optimum conditions of atmospheric or vacuum distillation. At present, the distribution of distillation temperatures is often investigated by simulated distillation (SIMDIS) using capillary gas chromatography (CGC) with a short capillary column with polydimethylsiloxane as the stationary phase. This paper presents the results of investigations on the possibility of replacing currently used CGC columns for SIMDIS with a deactivated fused silica capillary tube without any stationary phase. The SIMDIS technique making use of such an empty fused silica column allows a considerable lowering of elution temperature of the analytes, which results in a decrease of the final oven temperature while ensuring a complete separation of the mixture. This eliminates the possibility of decomposition of less thermally stable mixture components and bleeding of the stationary phase which would result in an increase of the detector signal. It also improves the stability of the baseline, which is especially important in the determination of the end point of elution, which is the basis for finding the final temperature of distillation. This is the key parameter for the safety process of hydrocracking, where an excessively high final temperature of distillation of a batch can result in serious damage to an expensive catalyst bed. This paper compares the distribution of distillation temperatures of the fraction from vacuum distillation of petroleum obtained using SIMDIS with that obtained by the proposed procedure. A good agreement between the two procedures was observed. In addition, typical values of elution temperatures of n-paraffin standards obtained by the two

Growth and Histopathological Effects of Chronic Exposition of Marine Pejerrey Odontesthes argentinensis Larvae to Petroleum Water-Soluble Fraction (WSF)

Energy Technology Data Exchange (ETDEWEB)

Gusmao, Emeline Pereira; Rodrigues, Ricardo Vieira; Moreira, Caue Bonucci [Programa de Pos-Graduacao em Aquicultura, Laboratorio de Piscicultura Estuarina e Marinha, Universidade Federal do Rio Grande, Rio Grande (Brazil); Romano, Luis Alberto; Sampaio, Luis Andre [Laboratorio de Piscicultura Estuarina e Marinha, Instituto de Oceanografia, Universidade Federal do Rio Grande, Rio Grande (Brazil); Miranda-Filho, Kleber Campos [Escola de Veterinaria, Departamento de Zootecnia, Laboratorio de Aquacultura, Universidade Federal de Minas Gerais, Belo Horizonte (Brazil)], e-mail: kmiranda2010@ufmg.br

2012-07-15

The water-soluble fraction (WSF) of petroleum contains a mixture of polycyclic aromatic hydrocarbons, volatile hydrocarbons, phenols, and heterocyclic compounds, considered deleterious to aquatic biota. Marine 'pejerrey' Odontesthes argentinensis (Teleostei: Atherinopsidae) has a great commercial importance in local fisheries and a high potential for aquaculture. The aim of this study was to evaluate the histopathological effects in 'pejerrey' larvae exposed to different concentrations of petroleum WSF. The chronic toxicity test was conducted with newly hatched larvae exposed for 21 days to sublethal concentrations of WSF (2.5, 5, 10, and 20 % of WSF), plus one control. Survival and growth were significantly lower in the highest concentration. Several histopathological changes were found in the gills (e.g., hyperplasia, aneurysms, edema, and necrosis), kidney (e.g., nuclear alterations, decrease in the hematopoietic cells), and liver (e.g., hypertrophy, karyorrhexis, and karyopyknosis). An index of branchial lesion was proposed to standardize gill lesions to different pollutants.

Petroleum supply monthly, March 1995 with data for January 1995

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-30

Data presented in this report for March 1995, describes the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States.

Growth and Desulfurization Kinetics of Rhodcoccus Erythropolis IGTS8 on Dibenzothiophen and Petroleum Fraction

International Nuclear Information System (INIS)

El-Temtamy, S.A.; Farahat, L.A.; Mostafa, Y.M.; Al-Shatnawi, D.F.; AI-Sayed, S.

2004-01-01

The growth Kinetics of Rhodococcus erythropolis IGTS8 on dibenzo-thiophene. DBT, of different initial concentrations as well as on two petroleum fractions namely untreated and hydrodesulfurized gasoline and gas oil have been investigated in batch cultures. Using dibenzothiophene as a substrate, the specific growth rates were found to decrease with increasing initial substrate concentration. The removal of dibenzothiophene from culture media was found to follow first order kinetics. The reaction rate constant., k, decreased with increasing substrate concentration. The decrease of both specific growth rate and reaction rate constant with increasing substrate concentration suggested substrate inhibition. The growth rate on untreated gasoline as well as on hydrodesulfurized gasoline gave nearly the same specific growth rates of 0.067 h-I while growth on gas oil gave a higher specific growth rate of 0.1h -1

Continuous fractional distillation of petroleum

Energy Technology Data Exchange (ETDEWEB)

1921-11-05

This invention has for its object a process of distillation, fractional, and continuous, of shale oil, tar, etc., characterized by the vapors leaving the evaporation chamber being forced, before condensation, to go over a continuous circuit. The vapors traverse first a preheater then return to the vaporization chamber in which they are passed along large surfaces and by application of the counter-current principle in contact with the liquid to be distilled. They stream through the chamber in a continuous manner (the quantity of vapor emitted in the circuit being determined in a manner to advance the distillation just to completion); the excess of vapor formed being removed from the circuit and sent to a condensing apparatus for fractionation.

Experimental Assessment of the Mass of Ash Residue During the Burning of Droplets of a Composite Liquid Fuel

Science.gov (United States)

Glushkov, D. O.; Zakharevich, A. V.; Strizhak, P. A.; Syrodoi, S. V.

2018-05-01

An experimental study has been made of the regularities of burning of single droplets of typical compositions of a composite liquid fuel during the heating by an air flow with a varied temperature (600-900 K). As the basic components of the compositions of the composite liquid fuel, use was made of the: waste of processing (filter cakes) of bituminous coals of ranks K, C, and T, waste motor, turbine, and transformer oils, process mixture of mazut and oil, heavy crude, and plasticizer. The weight fraction of a liquid combustible component (petroleum) product) ranged within 0-15%. Consideration has been given to droplets of a composite liquid fuel with dimensions (radius) of 0.5 to 2 mm. Conditions of low-temperature initiation of combustion to ensure a minimum possible mass of solid incombustible residue have been determined. Petroleum products have been singled out whose addition to the composition of the composite liquid fuel tends to increase the ash mass (compared to the corresponding composition without a liquid combustible component). Approximation dependences have been obtained which permit predicting the influence of the concentration of the liquid petroleum product as part of the composite liquid fuel on the ash-residue mass.

Study of sulfur and vanadium in heavy petroleum products

Energy Technology Data Exchange (ETDEWEB)

Novelli, J.M.

1982-10-01

Sulfur compounds in heavy oil fractions (>450/sup 0/C) are studied in the first part of this work. After chemical oxidation by metachloroperbenzoic acid to obtain sulfones, sulfur compounds are analyzed by infrared spectroscopy for their qualitative and quantitative repartition. The method can be applied for the study of sulfur containing molecules before and after structural modifications of petroleum fractions by any chemical refining processes. In a second part vanadium is characterized in asphalt by physicochemical and chemical methods. 80% of the vanadium in a Boscan asphalt is under the form of porphyrins. Different associations are evidenced in petroleum fractions and metalloporphyrins, but the liaison between the vanadyl group and heterocondensate from asphalts is the more frequent.

Overview and Computational Approach for Studying the Physicochemical Characterization of High-Boiling-Point Petroleum Fractions (350°C+ Approche informatique pour l’étude des propriétés physico-chimiques de fraction pétrolière lourde (350°C+

Directory of Open Access Journals (Sweden)

Plazas Tovar L.

2012-06-01

Full Text Available The processing and upgrading of high-boilingpoint petroleum fractions, containing a large number of components from different groups (paraffins, olefins, naphthenes, aromatics require an in-depth evaluation. In order to characterize them, their thermodynamic and thermophysical properties must be determined. This work presents a computational approach based on the breakdown of the petroleum fraction into pseudocomponents defined by a trial-and-error exercise in which the mass- and molar-balance errors were minimized. Cases studies are illustrated to three heavy residues 400°C+ from “W, Y and Z” crude oil. This procedure requires the boiling point distillation curve and the density of the whole fraction as the input bulk properties. The methods proposed according to available correlations in the literature and standard industrial methods were mainly used to estimate properties that include the basic properties (normal boiling point, density and Watson factor characterization, the thermodynamic properties (molar mass and critical properties and the thermophysical and transport properties (kinematic viscosity, thermal conductivity, specific heat capacity and vapor pressure. The methodology developed has shown to be a useful tool for calculating a remarkably broad range of physicochemical properties of high-boiling-point petroleum fractions with good accuracy when the bulk properties are available, since computational approach gave an overall absolute deviation lower than 10% when compared with the experimental results obtained in the research laboratories LDPS/LOPCA/UNICAMP. Le traitement et la valorisation des fractions pétrolières lourdes nécessitent une étude très détaillée dans la mesure où le pétrole contient un très grand nombre de composants différents (paraffines, oléfines, naphtènes, arômes. Afin de caractériser les fractions, il est indispensable de déterminer les propriétés thermodynamiques et thermophysiques des

Treatment of petroleum industry oil sludge by Rhodotorula sp

Energy Technology Data Exchange (ETDEWEB)

Shailubhai, K.; Rao, N.N.; Modi, V.V.

1984-06-01

A Rhodotorula sp., isolated from soil, which showed a versatile capacity to degrade various aromatic and aliphatic hydrocarbons, was used to treat oil sludge. As a result of treatment, there was significant decrease in BOD, COD and contents of various petroleum fractions. The susceptibility to degradation was in the following order: saturate fraction >aromatic fraction> asphaltic fraction.

Petroleum supply monthly, December 1998 with data for October 1998

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-12-01

Data presented in the Petroleum Supply Monthly (PSM) describe the supply and disposition of petroleum products in the US and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the US (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the US. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics. 82 tabs.

Petroleum supply monthly, March 1994

Energy Technology Data Exchange (ETDEWEB)

1994-03-30

Data presented in the Petroleum Supply Monthly (PSM) describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics. The tables and figures in the Summary Statistics section of the PSM present a time series of selected petroleum data on a US level. Most time series include preliminary estimates for one month based on the Weekly Petroleum Supply Reporting System; statistics based on the most recent data from the Monthly Petroleum Supply Reporting System (MPSRS); and statistics published in prior issues of the PSM and PSA. The Detailed Statistics tables of the PSM present statistics for the most current month available as well as year-to-date. In most cases, the statistics are presented for several geographic areas -- the United States (50 States and the District of Columbia), five PAD Districts, and 12 Refining Districts. At the US and PAD District level, the total volume and the daily rate of activities are presented. The statistics are developed from monthly survey forms submitted by respondents to the EIA and from data provided from other sources.

Anticonvulsant activity of the fractionated extract of Crinum jagus bulbs in experimental animals

Directory of Open Access Journals (Sweden)

Azikiwe CCA

2012-05-01

Full Text Available Objective: To investigate the anticonvulsant activity of the bulbs of Crinum jagus in experimental animals. Methods: The uprooted bulbs were air dried for a week and ground into creamy-paste. 200g of paste was macerated each in 2 litres of water, ethanol and petroleum ether and filtered after 48 h. The obtained filtrates were each evaporated at the appropriate temperature to solid residue. The residues were further fractionated with successive changes of petroleum ether, ethyl acetate and n-butanol into a pooled filtrate which was further evaporated to dry solid brown-paste. Phytochemistry was carried out based on Treas and Evans method of 1987. The acute toxicity study (LD50 was carried based on Lorke ’s 1983 method. Convulsion was induced using maximum electric shock (MEST, pentylenetetrazole(PTZ, strychnine and Picrotoxin in the appropriate animal models. Seizures onset time and death time were used as successful induction of convulsion while prolongations of these features were taken as anticonvulsant activity. Results where possible, were statistically analyzed using SPSS-16.0 version. Results: The LD 50 was got at 1118.003mg/kg (IP in mice using Lorke ’s 1983 method. Fractionated extract of Crinum jagus exhibited dose dependent antiseizure against MEST induced seizure (P<0.001 and comparable to that of phenytoin, a standard anti generalized tonic-clonic seizure. There were also observable antiseizure activity of the fractionated extracts against PTZ, strychnine and Picrotoxin induced seizure and comparable to their standard corresponding antiseizures. Conclusions: We conclude that the bulbs of Crinum jagus possess proven broad spectrum antiseizure and perhaps antiepileptogenic activity thus justifies its use in traditional medicine. Clinical trial in man is recommended.

Natural radioactivity in petroleum residues

International Nuclear Information System (INIS)

Gazineu, M.H.P.; Gazineu, M.H.P.; Hazin, C.A.; Hazin, C.A.

2006-01-01

The oil extraction and production industry generates several types of solid and liquid wastes. Scales, sludge and water are typical residues that can be found in such facilities and that can be contaminated with Naturally Occurring Radioactive Material (N.O.R.M.). As a result of oil processing, the natural radionuclides can be concentrated in such residues, forming the so called Technologically Enhanced Naturally Occurring Radioactive Material, or T.E.N.O.R.M.. Most of the radionuclides that appear in oil and gas streams belong to the 238 U and 232 Th natural series, besides 40 K. The present work was developed to determine the radionuclide content of scales and sludge generated during oil extraction and production operations. Emphasis was given to the quantification of 226 Ra, 228 Ra and 40 K since these radionuclides,are responsible for most of the external exposure in such facilities. Samples were taken from the P.E.T.R.O.B.R.A.S. unity in the State of Sergipe, in Northeastern Brazil. They were collected directly from the inner surface of water pipes and storage tanks, or from barrels stored in the waste storage area of the E and P unit. The activity concentrations for 226 Ra, 228 Ra and 40 K were determined by using an HP Ge gamma spectrometric system. The results showed concentrations ranging from 42.7 to 2,110.0 kBq/kg for 226 Ra, 40.5 to 1,550.0 kBq/kg for 228 Ra, and 20.6 to 186.6 kBq/kg for 40 K. The results highlight the importance of determining the activity concentration of those radionuclides in oil residues before deciding whether they should be stored or discarded to the environment. (authors)

Characterization of liquid products from the co-cracking of ternary and quaternary mixture of petroleum vacuum residue, polypropylene, Samla coal and Calotropis Procera

Energy Technology Data Exchange (ETDEWEB)

M. Ahmaruzzaman; D.K. Sharma [Indian Institute of Technology Delhi, New Delhi (India). Centre for Energy Studies

2008-08-15

The co-cracking of the petroleum vacuum residue (XVR) with polypropylene (PP), Samla coal (SC) and Calotropis procera (CL) has been carried out in a batch reactor under isothermal conditions at atmospheric pressure. The liquids obtained by co-cracking have been characterized by Fourier transform infrared spectroscopy, high performance liquid chromatography, {sup 1}H nuclear magnetic resonance (NMR), {sup 13}C NMR, gel permeation chromatography (GPC), and inductively coupled argon plasma analyses. It was found that the liquid products obtained from the co-cracking of ternary and quaternary mixtures of the petroleum vacuum residue with polypropylene, coal and C. procera contained less than 1 ppm of Ni and V. The HPLC analyses indicates that the liquids obtained from the cracking of ternary mixture of XVR+PP+CL were mainly aliphatic in nature (saturates content 87.4%). NMR analyses showed that the aromatic carbon contents decreased (15.0%) in the liquid products derived from the co-cracking of quaternary mixtures of XVR+PP+SC+CL compared to their theoretical averages (taking the averages of aromatic carbon contents of the liquids from XVR, PP, SC and CL individually). The overall results indicated that there exists a definite interaction of reactive species when XVR, PP, SC and CL were co-cracked together. 27 refs., 5 tabs.

Review of preliminary results of the project `Co-cracking of plastics and petroleum residues`; Uebersicht zu den ersten Ergebnissen des Projektes Cocracking von Kunststoffen und Erdoelrueckstand

Energy Technology Data Exchange (ETDEWEB)

Uhmann, R; Koepsel, R F; Kuchling, T; Simanjenkov, V [Technische Univ. Bergakademie Freiberg (Germany). Inst. fuer Energieverfahrenstechnik und Chemieingenieurwesen

1998-09-01

Coprocessing of petroleum residues and plastics is a promising technology, although some problems concerning waste plastics must be clarified prior to its implementation. In general, it can be stated that with a careful choice of operating parameter combinations, oil yields will be higher than for thermal treatment of petroleum residues alone (e.g. a 35% yield increase is achieved by adding 25% of plastics, which is a disproportionately high increase). Waste plastics thus become a valuable material for processing. (orig.) [Deutsch] Das untersuchte Coprocessing von VR und Kunststoffen ist ein erfolgversprechender Weg der Kunststoffverwertung und des tiefen Crackens von Erdoelrueckstand. Die Klaerung der mit Altkunststoffen verbundenen Fragen bedarf weiterer Untersuchungen. Allgemein kann festgestellt werden, dass bei entsprechenden Parameterkombinationen bessere Oelausbeuten erzielt werden als bei der thermischen Behandlung von reinem VR. Ein Beispiel dafuer ist in der Abbildung 10 dargestellt. Durch eine 25%-ige Erhoehung der Einsatzstoffmasse durch Kunststoffzugabe wird eine im Vergleich zu reinem VR um ca. 36% hoehere Oelausbeute erzielt, was einer ueberproportionalen Erhoehung entspricht. Altkunststoff wird bei diesem Prozess unter Nutzung des Wasserstoff-potentials von Polymeren zu einem wertvollen Einsatzstoff. (orig.)

Petroleum supply monthly, August 1995 with data for June 1995

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-08-25

Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

Petroleum supply monthly, March 1999, with data for January 1999

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The Petroleum Supply Monthly (PSM) is one of a family of four petroleum supply publications produced by the Petroleum Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the US and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the US (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the US. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

In vitro photooxidation of a crude Iranian petroleum maltenic fraction as a film over seawater in natural simulated conditions and identification of photoproducts

International Nuclear Information System (INIS)

Nahri-Niknafs, B.; Ghotbesharif, S.J.; Taghvaei, S.; Rustayian, A.H.

2004-01-01

Photooxidation is a transformation pathway for oil spilled in the marine environment. Most crude oils spilled at sea spread rapidly to form slicks over a large surface areas. Oil entering the seas can have a harmful impact on marine ecosystems and on the commercial and recreation resources of coastal areas. The spilled oil undergoes physical changes such as dispersion, photooxidation, evaporation, and dissolution. These changes are accompanied by changes in density, viscosity and interfacial tension. It is important to understand the effect petroleum photooxidation and degradation in order to determine the fate of the spilled oil in a marine environment. This study presents a reliable method for examining the nature of the photoproducts and the composition of the residual hydrocarbons on an oil film over seawater. In this study, the maltenic fraction of Iranian oil was exposed to sunlight as a film of oil over seawater. The authors examined the effect of ultraviolet illumination of gas chromatography-mass spectrometry and Fourier Transform Infrared analytical methods. The study revealed that the saturated hydrocarbons were resistant, but the aromatic hydrocarbons were found to be sensitive to photochemical degradation. The sensitivity of aromatic compounds to photooxidation was increased by increasing the size and alkyl substitution. 14 refs., 2 tabs., 1 fig

Compostagem da fração sólida da água residuária de suinocultura Solid fraction composting of residual water from pig farms

Directory of Open Access Journals (Sweden)

Marco A. P. Orrico Júnior

2009-09-01

Full Text Available Avaliar o desenvolvimento do processo de compostagem utilizando como substrato à fração sólida da água residuária de suinocultura foi o objetivo deste trabalho. Para a obtenção da fração sólida, a água residuária de suinocultura foi submetida ao peneiramento, utilizando-se de peneira com malha de 1 milímetro. Após separação, a fração sólida foi utilizada para a confecção de três leiras de compostagem, em pátio com piso de concreto e cobertura plástica. Durante a compostagem da fração sólida da água residuária de suinocultura, foram avaliados: temperatura, reduções de sólidos totais (ST, sólidos voláteis (SV, demanda química de oxigênio (DQO, carbono orgânico, matéria orgânica compostável (MOC, matéria orgânica resistente à compostagem (MORC, números mais prováveis (NMPs de coliformes totais e coliformes termotolerantes, além do volume e dos teores de nutrientes no composto. A compostagem mostrou-se eficiente no tratamento da fração sólida da água residuária de suinocultura devido à elevada minimização do poder poluente dos dejetos, observando-se reduções de 71,24% nos teores de ST, 64,55% no volume, 56,89% no teor de DQO e 56,89% na MOC. Foram verificadas reduções de 100% nos NMPs de coliformes totais e termotolerantes, o que possibilita seu uso como adubo orgânico.This work aimed to evaluate the development of the composting process by using the solid fraction of residual water from a pig farm. To obtain the solid fraction, the residual water was sewed in a 1mm screen sew. After separation, the solid fraction was used to form three composting piles, on a patio with concrete floor and plastic cover. During composting the solid fraction of residual water from pig farms was monitored: temperature, total solids reduction (TS, volatile solids (VS chemical demand for oxygen (CDO, organic carbon, compostable organic matter (COM, organic matter resistant to composting (OMRC, most probable

Soybean lecithin: acetone insoluble residue fractionation and their volatile components

Directory of Open Access Journals (Sweden)

Aly, Saadia M.

2002-09-01

Full Text Available The acetone insoluble residue was isolated from soybean lecithin. This residue was solvent fractionated resulted in four fractions, namely, acetic acid soluble, acetic acid insoluble, benzene phase and benzene insoluble phase. Concerning phospholipid constitution of these four fractions, it was found that the first fraction contains PC, PE and PI in percentages of 56.0, 21.6 and 19.0 respectively. The 2nd fraction makes 39 % PC and 60 % CER, besides some traces of PE and PI. The benzene phase is mainly all PC with some traces of PE. The last fraction is 80.6 % CER and 20 % PC. The fatty acid composition of these four fractions besides soluble in acetone, crude and degummed soybean oil and total phospholipids was recorded. Generally, it was found that the major saturated and unsaturated fatty acids were palmitic and linoleic. Volatile components of these samples except acetic acid insoluble were reported. Fourty nine compounds were separated. Thirty two components including aliphatic aldehydes, ketones, alcohols, esters and acids were identified. Aldehydes and ketones showed a changed through the seven samples. They increased by degumming.4,5-Dimethylelisoxazole had a strong lecithin like flavour, so it can be used as an indicator for the degumming process.2-Pentylfuran showed a significant decrease by degumming. Other compounds, such as esters and alcohols had no distinguish effect on the volatile products through process.El residuo insoluble en acetona fue aislado de la lecitina de soja. Este residuo fue fraccionado por solventes en cuatro fracciones: soluble en ácido acético, insoluble en ácido acético, fase benceno y fase insoluble en benceno. Concerniente a la constitución de los fosfolípidos de estas cuatro fracciones, se encontró que la primera fracción contiene PC, PE y PI en porcentajes del 56.0, 21.6 y 19.0 respectivamente. La segunda fracción tuvo 39 % PC y 60 % CER, junto a algunas trazas de PE y PI. La fase benceno est

Petroleum supply annual 1996: Volume 1

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-06-01

The Petroleum Supply Annual (PSA) contains information on the supply and disposition of crude oil and petroleum products. The publication reflects data that were collected from the petroleum industry during 1996 through annual and monthly surveys. The PSA is divided into two volumes. This first volume contains three sections: Summary Statistics, Detailed Statistics, and Refinery Capacity; each with final annual data. The summary statistics section show 16 years of data depicting the balance between supply, disposition and ending stocks for various commodities including crude oil, motor gasoline, distillate fuel oil, residual fuel oil, jet fuel propane/propylene, and liquefied petroleum gases. The detailed statistics section provide 1996 detailed statistics on supply and disposition, refinery operations, imports and exports, stocks, and transportation of crude oil and petroleum products. The refinery capacity contain listings of refineries and associated crude oil distillation and downstream capacities by State, as of January 1, 1997, as well as summaries of corporate refinery capacities and refinery storage capacities. In addition, refinery receipts of crude oil by method of transportation for 1996 are provided. Also included are fuels consumed at refineries, and lists of shutdowns, sales, reactivations, and mergers during 1995 and 1996. 16 figs., 59 tabs.

Petroleum supply annual 1996: Volume 1

International Nuclear Information System (INIS)

1997-06-01

The Petroleum Supply Annual (PSA) contains information on the supply and disposition of crude oil and petroleum products. The publication reflects data that were collected from the petroleum industry during 1996 through annual and monthly surveys. The PSA is divided into two volumes. This first volume contains three sections: Summary Statistics, Detailed Statistics, and Refinery Capacity; each with final annual data. The summary statistics section show 16 years of data depicting the balance between supply, disposition and ending stocks for various commodities including crude oil, motor gasoline, distillate fuel oil, residual fuel oil, jet fuel propane/propylene, and liquefied petroleum gases. The detailed statistics section provide 1996 detailed statistics on supply and disposition, refinery operations, imports and exports, stocks, and transportation of crude oil and petroleum products. The refinery capacity contain listings of refineries and associated crude oil distillation and downstream capacities by State, as of January 1, 1997, as well as summaries of corporate refinery capacities and refinery storage capacities. In addition, refinery receipts of crude oil by method of transportation for 1996 are provided. Also included are fuels consumed at refineries, and lists of shutdowns, sales, reactivations, and mergers during 1995 and 1996. 16 figs., 59 tabs

Structure and properties of compositions based on petroleum sulfonic acids

Energy Technology Data Exchange (ETDEWEB)

Tutorskii, I.A.; Sultanova, A.S.; Belkina, E.V.; Fomin, A.G. [Lomonosov Academy of Fine Chemical Technology, Moscow (Russian Federation)

1995-03-01

Colloidal characteristics of compositions based on petroleum sulfonic acids were studied. Neutralized heavy oil residue exhibits surface-active properties and contains an ultradisperse filler. Analysis of the compositions by size-exclusion-chromatography shows deep structural changes in the heavy acid residue upon neutralization with calcium carbonate.

Petroleum marketing monthly with data for April 1997

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-07-01

This publication provides information and statistical data on a variety of crude oil costs and refined petroleum products sales. Data on crude oil include the domestic first purchase price, the free on board price and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The data provided are compiled from six Energy Information Administration survey forms. 50 tabs.

Removal of residual contaminants in petroleum-contaminated soil by Fenton-like oxidation

Energy Technology Data Exchange (ETDEWEB)

Lu Mang [School of Material Science and Engineering, Jingdezhen Ceramic Institute, Jingdezhen, 333001, Jiangxi Province (China); State Key Laboratory of Heavy Oil Processing, China University of Petroleum, Beijing 102249 (China); Zhang Zhongzhi, E-mail: zzzhang1955@hotmail.com [State Key Laboratory of Heavy Oil Processing, China University of Petroleum, Beijing 102249 (China); Qiao Wei; Guan Yueming; Xiao Meng; Peng Chong [State Key Laboratory of Heavy Oil Processing, China University of Petroleum, Beijing 102249 (China)

2010-07-15

The degradation of bioremediation residues by hydrogen peroxide in petroleum-contaminated soil was investigated at circumneutral pH using a Fenton-like reagent (ferric ion chelated with EDTA). Batch tests were done on 20 g soil suspended in 60 mL aqueous solution containing hydrogen peroxide and Fe{sup 3+}-EDTA complex under constant stirring. A slurry reactor was used to treat the soil based on the optimal reactant conditions. Contaminants were characterized by Fourier transform infrared spectroscopy and Fourier transform ion cyclotron resonance mass spectrometry. The results showed that the optimal treatment condition was: the molar ratio of hydrogen peroxide to iron = 200:1, and pH 7.0. Under the optimum condition, total dichloromethane-extractable organics were reduced from 14,800 to 2300 mg kg{sup -1} soil when the accumulative H{sub 2}O{sub 2} dosage was 2.45 mol kg{sup -1} soil during the reactor treatment. Abundance of viable cells was lower in incubated Fenton-like treated soil than in untreated soil. Oxidation of contaminants produced remarkable compositional and structural modifications. A fused ring compound, identified as C{sub 34}H{sub 38}N{sub 1}, was found to exhibit the greatest resistance to oxidation.

Petroleum marketing monthly, December 1996 with data for September 1996

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-12-01

This report provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. 7 figs., 50 tabs.

New guidelines for oil spill identification of waterborne petroleum and petroleum products

Energy Technology Data Exchange (ETDEWEB)

Faksness, L.G.; Daling, P.S. [SINTEF Energy Research, Trondheim (Norway); Hansen, A.B. [National Environmental Research Inst., Roskilde (Denmark); Kienhuis, P. [RIZA, (Netherlands); Duus, R. [Norwegian Standard Association (Norway)

2005-07-01

Advances in interpretive and analytical methods have opened the possibility to improve the existing Nordtest methodology for oil spill identification which was developed in 1991 under the Nordic Council of Ministers. In 2002, the European Committee for Standardization (CEN) established 2 working groups to revise the Nordtest Methodology into the following 2 CEN guidelines: (1) oil spill identification which includes waterborne and petroleum products, and (2) oil spill identification which in addition to including waterborne petroleum and petroleum products, includes analytical methodology and interpretation of results. The revised methodology includes a protocol/decision chart that has 3 tiered levels of analyses and data treatment. The methodology relies on the characterization of diagnostic ratios. The CEN working group intends to use the guidelines as a basis for a national oil spill identification protocol in each European country and for further international use. The methodology can be applied to oil samples of petrogenic origin with boiling points above 200 degrees C, such as crude oils, diesel fuel oils, residual bunker oils, lubricants, and mixtures of oily bilge and sludge samples. It is not intended for automotive gasolines or other light petroleum products. The method has been implemented in most forensic laboratories in Europe and has successfully differentiated between oils from a spill and possible pollution sources. 19 refs., 4 tabs., 10 figs.

New guidelines for oil spill identification of waterborne petroleum and petroleum products

International Nuclear Information System (INIS)

Faksness, L.G.; Daling, P.S.; Hansen, A.B.; Kienhuis, P.; Duus, R.

2005-01-01

Advances in interpretive and analytical methods have opened the possibility to improve the existing Nordtest methodology for oil spill identification which was developed in 1991 under the Nordic Council of Ministers. In 2002, the European Committee for Standardization (CEN) established 2 working groups to revise the Nordtest Methodology into the following 2 CEN guidelines: (1) oil spill identification which includes waterborne and petroleum products, and (2) oil spill identification which in addition to including waterborne petroleum and petroleum products, includes analytical methodology and interpretation of results. The revised methodology includes a protocol/decision chart that has 3 tiered levels of analyses and data treatment. The methodology relies on the characterization of diagnostic ratios. The CEN working group intends to use the guidelines as a basis for a national oil spill identification protocol in each European country and for further international use. The methodology can be applied to oil samples of petrogenic origin with boiling points above 200 degrees C, such as crude oils, diesel fuel oils, residual bunker oils, lubricants, and mixtures of oily bilge and sludge samples. It is not intended for automotive gasolines or other light petroleum products. The method has been implemented in most forensic laboratories in Europe and has successfully differentiated between oils from a spill and possible pollution sources. 19 refs., 4 tabs., 10 figs

Petroleum marketing monthly, September 1990. [Contains Glossary

Energy Technology Data Exchange (ETDEWEB)

1990-12-11

This report is designed to give information and statistical data about a variety of crude oils and refined petroleum products. The publication provides statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, education institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners' acquisition cost of crude oil. Sales data for motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane are presented. 12 figs., 55 tabs.

Petroleum marketing monthly, October 1991. [Contains glossary

Energy Technology Data Exchange (ETDEWEB)

1991-10-10

This report is designed to give information and statistical data about a variety of crude oils and refined petroleum products. The publication provides statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiner's acquisition cost of crude oil. Sales data for motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane are presented. 12 figs., 55 tabs.

Characteristics of bicyclic sesquiterpanes in crude oils and petroleum products.

Science.gov (United States)

Yang, Chun; Wang, Zhendi; Hollebone, Bruce P; Brown, Carl E; Landriault, Mike

2009-05-15

This study presents a quantitative gas chromatography-mass spectrometry analysis of bicyclic sesquiterpanes (BSs) in numerous crude oils and refined petroleum products including light and mid-range distillate fuels, residual fuels, and lubricating oils collected from various sources. Ten commonly recognized bicyclic sesquiterpanes were determined in all the studied crude oils and diesel range fuels with principal dominance of BS3 (C(15)H(28)), BS5 (C(15)H(28)) and BS10 (C(16)H(30)), while they were generally not detected or in trace in light fuel oils like gasoline and kerosene and most lubricating oils. Laboratory distillation of crude oils demonstrated that sesquiterpanes were highly enriched in the medium distillation fractions of approximately 180 to 481 degrees C and were generally absent or very low in the light distillation fraction (boiling point to approximately 180 degrees C) and the heavy residual fraction (>481 degrees C). The effect of evaporative weathering on a series of diagnostic ratios of sesquiterpanes, n-alkanes, and biomarkers was evaluated with two suites of weathered oil samples. The change of abundance of sesquiterpanes was used to determine the extent of weathering of artificially evaporated crude oils and diesel. In addition to the pentacyclic biomarker C(29) and C(30) alphabeta-hopane, C(15) and C(16) sesquiterpanes might be alternative internal marker compounds to provide a direct way to estimate the depletion of oils, particularly diesels, in oil spill investigations. These findings may offer potential applications for both oil identification and oil-source correlation in cases where the tri- to pentacyclic biomarkers are absent due to refining or environmental weathering of oils.

Petroleum supply monthly, November 1996 with data for September 1996

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-11-01

Data presented in this report describes the supply and disposition of petroleum products in the US and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products fin the US (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the US. The tables and figures in the Summary Statistics section present a time series of selected petroleum data on a US level. The Detailed Statistics tables present statistics for the most current month available as well as year-to-date. 16 figs., 66 tabs.

Petroleum supply monthly: September 1996, with data for July 1996

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-09-01

Data presented in this report describe the supply and disposition of petroleum products in the US and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the US (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the US. The tables and figures in the Summary Statistics section of the PSM present a time series of selected petroleum data on a US level. The Detailed Statistics tables of the PSM present statistics for the most current month available as well as year-to-date. 56 tabs.

Petroleum supply monthly, September 1995 with data for July 1995

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-09-27

The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

Petroleum supply monthly, May 1995 with data for March 1995

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-05-25

The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States.Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

Petroleum Supply Monthly, March 1996 (with data for January 1996)

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-04-04

The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

Petroleum Supply Monthly, September 1998, with data for July 1998

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-09-28

The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the suppiy and disposition of petroleum products in the United States and major U.S. geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics

Petroleum supply monthly, May 1999, with data for March 1999

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-05-01

Data presented in the Petroleum Supply Monthly (PSM) describe the supply and disposition of petroleum products in the US and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary supplies of petroleum products in the US (50 states and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the US. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics. The tables and figures in the Summary Statistics section of the PSM present a time series of selected petroleum data on a US level. The Detailed Statistics tables of the PSM present statistics for the most current month available as well as year-to-date. 72 tabs.

Petroleum supply monthly, June 1999, with data for April 1999

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-06-01

Data presented in the Petroleum Supply Monthly (PSM) describe the supply and disposition of petroleum products in the US and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the US (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the US. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics. The tables and figures in the Summary Statistics section of the PSM present a time series of selected petroleum data on a US level. The Detailed Statistics tables of the PSM present statistics for the most current month available as well as year-to-date. 16 figs., 66 tabs.

Petroleum supply monthly, April 1999, with data for February 1999

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-04-01

Data presented in the Petroleum Supply Monthly (PSM) describe the supply and disposition of petroleum products in the US and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the US (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the US. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics. The tables and figures in the Summary Statistics section of the PSM present a time series of selected petroleum data on a US level. The Detailed Statistics tables of the PSM present statistics for the most current month available as well as year-to-date. 72 tabs.

Petroleum supply monthly, November 1998, with data for September 1998

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-11-01

Data presented in the Petroleum Supply Monthly (PSM) describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the Unites States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics. The tables and figures in the Summary Statistics section of the PSM present a time series of selected petroleum data on a US level. The Detailed Statistics tables of the PSM present statistics for the most current month available as well as year-to-date. 72 tabs.

Petroleum supply monthly, December 1997 with data from October 1997

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-01

Data presented in the Petroleum Supply Monthly (PSM) describes the supply and disposition of petroleum products in the US and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the US (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregates, the data reported by these sectors approximately represent the consumption of petroleum products in the US. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics. The tables and figures in the Summary Statistics section of the PSM present a time series of selected petroleum data on a US level. The Detailed Statistics tables of the PSM present statistics for the most current month available as well as year-to-date. 16 figs., 66 tabs.

Petroleum supply monthly, January 1999 with data for November 1998

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-01-01

Data presented in the Petroleum Supply Monthly (PSM) describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics. The tables and figures in the Summary Statistics section of the PSM present a time series of selected petroleum data on a US level. The Detailed Statistics tables of the PSM present statistics for the most current month available as well as year-to-date. 82 tabs.

Petroleum supply monthly, July 1997 with data from May 1997

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-07-01

Data presented in the Petroleum Supply Monthly (PSM) describes the supply and disposition of petroleum products in the US and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the US (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the US. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics. The tables and figures in the Summary Statistics section of the PSM present a time series of selected petroleum data on a US level. The Detailed Statistics tables of the PSM present statistics for the most current month available as well as year-to-date. 16 figs., 66 tabs.

Petroleum supply monthly, February 1999, with data for December 1998

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-02-01

Data presented in the Petroleum Supply Monthly (PSM) describes the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics. The tables and figures in the Summary Statistics section of the PSM present a time series of selected petroleum data on a US level. The Detailed Statistics tables of the PSM present statistics for the most current month available as well as year-to-date. 16 figs., 66 tabs.

Petroleum supply monthly, August 1998, with data for June 1998

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-08-01

Data presented in the Petroleum Supply Monthly (PSM) describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the US (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics. The tables and figures in the Summary Statistics section of the PSM present a time series of selected petroleum data on a US level. The Detailed Statistics tables of the PSM present statistics for the most current month available as well as year-to-date. 16 fig., 66 tabs.

Petroleum supply monthly: July 1998, with data for May 1998

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-07-01

Data presented in the Petroleum Supply Monthly (PSM) describes the supply and disposition of petroleum products in the US and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the US (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the US. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics. The tables and figures in the Summary Statistics section of the PSM present a time series of selected petroleum data on a US level. The Detailed Statistics tables of the PSM present statistics for the most current month available as well as year-to-date. 16 figs., 56 tabs.

Petroleum supply monthly, January 1997 with data for November 1996

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-01-01

Data presented in the Petroleum Supply Monthly describe the supply and disposition of petroleum products in the US and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the US (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the US. Data are divided into two sections: Summary Statistics and Detailed Statistics. The tables and figures in the Summary Statistics section present a time series of selected petroleum data on a US level. The Detailed Statistics tables present statistics for the most current month available as well as year-to-date. 16 figs., 66 tabs.

Petroleum supply monthly, May 1996 with data from March 1996

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-05-01

Data presented in the Petroleum Supply Monthly (PSM) describe the supply and disposition of petroleum products in the US and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the US (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the US. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics. The tables and figures in the Summary Statistics section of the PSM present a time series of selected petroleum data on a US level. The Detailed Statistics tables of the PSM present statistics for the most current month available as well as year-to-date. 16 figs., 66 tabs.

Petroleum Hydrocarbons Contamination Profile of Ochani Stream in ...

African Journals Online (AJOL)

Michael Horsfall

ABSTRACT: Petroleum hydrocarbon contamination profile, heavy metals and .... potential conduits for oil and water migrating from the ... by Gas Chromatography: Soil / sediment / sludge ..... fractions contained in the dump pits) which have.

Taking the petroleum out of petrochemistry

Energy Technology Data Exchange (ETDEWEB)

Yamamoto, T

1982-01-01

It is thought to be inevitable that world production of petroleum will start declining in the not too distant future. When this happens, the only feedstock for the organic chemicals industry and the polymer chemistry industry will be coal. It is emphasized that the best way of substituting coal for petroleum fractions as an alternative energy source is the technologically easy conversion of economic coal to methanol. There are explanations of the problems involved in obtaining fuel methanol as an energy source, as feedstock for the chemical industry, and as a raw material for chemistry. (13 refs.)

Microbial activity and soil organic matter decay in roadside soils polluted with petroleum hydrocarbons

Science.gov (United States)

Mykhailova, Larysa; Fischer, Thomas; Iurchenko, Valentina

2015-04-01

It has been demonstrated previously that hydrocarbon addition to soil provokes soil organic matter priming (Zyakun et al., 2011). It has further been shown that petroleum hydrocarbons deposit to roadside soils bound to fine mineral particles and together with vehicle spray (Mykhailova et al., 2014), and that hydrocarbon concentrations decrease to safe levels within the first 15 m from the road, reaching background concentrations at 60-100 m distance (Mykhailova et al., 2013). It was the aim of this study to (I) identify the bioavailability of different petroleum hydrocarbon fractions to degradation and to (II) identify the native (i.e. pedogenic) C fraction affected by hydrocarbon-mediated soil organic matter priming during decay. To address this aim, we collected soil samples at distances from 1 to 100 m (sampling depth 15 cm) near the Traktorostroiteley avenue and the Pushkinskaya street in Kharkov, as well as near the country road M18 near Kharkov, Ukraine. The roads have been under exploitation for several decades, so microbial adaptation to enhanced hydrocarbon levels and full expression of effects could be assumed. The following C fractions were quantified using 13C-CP/MAS-NMR: Carbohydrates, Proteins, Lignin, Aliphates, Carbonyl/Carboxyl as well as black carbon according to Nelson and Baldock (2005). Petroleum hydrocarbons were determind after hexane extraction using GC-MS and divided into a light fraction (chain-length C27, Mykhailova et al., 2013). Potential soil respiration was determined every 48 h by trapping of CO2 evolving from 20 g soil in NaOH at 20 ° C and at 60% of the maximum water holding capacity and titration after a total incubation period of 4 weeks in the lab. It was found that soil respiration positively correlated with the ratio of the light fraction to the sum of medium and heavy fractions of petroleum hydrocarbons, which indicates higher biodegradation primarily of the light petroleum hydrocarbon fraction. Further, soil respiration was

Speciation of Mercury in Selected Areas of the Petroleum Value Chain.

Science.gov (United States)

Avellan, Astrid; Stegemeier, John P; Gai, Ke; Dale, James; Hsu-Kim, Heileen; Levard, Clément; O'Rear, Dennis; Hoelen, Thomas P; Lowry, Gregory V

2018-02-06

Petroleum, natural gas, and natural gas condensate can contain low levels of mercury (Hg). The speciation of Hg can affect its behavior during processing, transport, and storage so efficient and safe management of Hg requires an understanding of its chemical form in oil, gas and byproducts. Here, X-ray absorption spectroscopy was used to determine the Hg speciation in samples of solid residues collected throughout the petroleum value chain including stabilized crude oil residues, sediments from separation tanks and condensate glycol dehydrators, distillation column pipe scale, and biosludge from wastewater treatment. In all samples except glycol dehydrators, metacinnabar (β-HgS) was the primary form of Hg. Electron microscopy on particles from a crude sediment showed nanosized (crude oil being processed, i.e. sweet (low sulfur crudes) vs sour (higher sulfur crudes). This information on Hg speciation in the petroleum value chain will inform development of better engineering controls and management practices for Hg.

Petroleum hydrocarbon concentration in surface sediments in continental shelf region along the central west coast of India

Digital Repository Service at National Institute of Oceanography (India)

Ram, A.; Kadam, A.N.

Gas chromatography revealed that nonpolar material extracted from surface sediments collected along the northern west coast of India was originated from petroleum hydrocarbon residue. Petroleum hydrocarbon levels as determinEd. by fluorescence...

Petroleum supply monthly, October 1998, with data for August 1998

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-10-01

Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics. The tables and figures in the Summary Statistics section of the PSM present a time series of selected petroleum data on a US level. The Detailed Statistics tables of the PSM present statistics for the most current month available as well as year-to-date. A feature article, Accuracy of petroleum supply data, is also included. 72 tabs.

Contribution of offshore petroleum deposits to marine food chain

Science.gov (United States)

Mori, S.

2009-12-01

Petroleum production out of offshore petroleum deposits often coincides with abundant fisheries in the world. Superposition of marine microorganism concentration distribution and offshore petroleum field distribution from various data in the literature provides to prove this coincidence. Sakhalin Island coastal regions, North Sea, Gulf of Mexico, etc. are chosen for the superpositions. Significant conformity is observed between the plankton concentration distribution and the offshore petroleum deposit distribution in all those regions. Also, most studies on the consequence of oil spills to marine eco-systems have focused mainly on hazardous marine pollution caused by spilled petroleum at high concentration in marine environment. However, some of those data clearly indicate stimulation of plankton population in properly low concentration levels of dissolved hydrocarbons and dissolved petroleum compositions. Further, increase of hydrocarbon concentration leads to its inhibition from its stimulation conditions upon crossing over a critical concentration level—a plankton stimulation/inhibition threshold concentration (SITC) of hydrocarbons. The SITC varies depending on hydrocarbon compounds, petroleum compositions, and microorganisms such as planktons. Further, petroleum composition diffusing through subterranean layers from petroleum deposits reacts with dissolved oxygen to be consumed at the ocean floor to precipitate the agglomerate suspension of hydrocarbons, leaving the sea water in a condition of oxygen depletion on the ocean floor. Such incidents are also briefly discussed.Plankton stimulation/inhibition threshold concentration of petroleum fractions

Process for recovering, destroying or displacing a petroleum product on the surface of a liquid

Energy Technology Data Exchange (ETDEWEB)

Godin, G H.F.; Bringer Quertier, G M.L.

1969-01-06

This process consists in first immobilizing the petroleum product on the surface of water by means of pieces or strips of polyethylene plastic. The petroleum product is then either collected and separated from water, or burned in place. After burning, the solid residue is towed to shore and burned a second time, after which neither ash nor residue is left. The proportion of polyethylene to be used is 1:20 if the product is collected, 1:35 if it is burned.

The conversion of waste plastics/petroleum residue mixtures to transportation fuels

International Nuclear Information System (INIS)

Ali, M.F.; Siddiqui, M.N.

2005-01-01

Plastics have become the material of choice in the modern world and its applications in the industrial field are continually increasing. Presently the plastics are manufactured for various uses such as: consumer packaging, wires, pipes, containers, bottles, appliances, electrical/electronic parts, computers and automotive parts. Most of he post consumer, plastic products are discarded and end up as mixed plastic municipal waste. The disposal of his waste has become a major social concern. Mixed plastic waste (MPW) recycling is still very much in its infancy. Approximately 20 million tons of plastic waste is generated in the United States of America, while about 15 million tons is generated throughout the Europe. With existing recycle efforts, only 7% of the MPW are recycled to produce low-grade plastic products such as plastic sacks, pipes, plastic fencing, and garden furniture. The current plastic reclamation technology options are generally grouped into the following four types: (i) Primary: The processing of plastic for use comparable to the original application. (ii) Secondary: The processing of plastics waste into new products with a lower quality level. (iii) Tertiary: The chemical or thermal processing of plastic waste to their basic hydrocarbon feedstock. The resulting raw materials are then reprocessed into plastic material or other products of the oil refining process. (iv) Quaternary: The incineration of plastics waste to recover energy. This paper deals exclusively with tertiary recycling by pyrolysis and catalytic cracking of plastics waste alone and by coprocessing with petroleum residue or heavy oils to fuels and petrochemical feedstock for further processing in existing refinery and petrochemical units. (author)

Material-balance assessment of the New Albany-Chesterian petroleum system of the Illinois basin

Science.gov (United States)

Lewan, M.D.; Henry, M.E.; Higley, D.K.; Pitman, Janet K.

2002-01-01

The New Albany-Chesterian petroleum system of the Illinois basin is a well-constrained system from which petroleum charges and losses were quantified through a material-balance assessment. This petroleum system has nearly 90,000 wells penetrating the Chesterian section, a single New Albany Shale source rock accounting for more than 99% of the produced oil, well-established stratigraphic and structural frameworks, and accessible source rock samples at various maturity levels. A hydrogen index (HI) map based on Rock-Eval analyses of source rock samples of New Albany Shale defines the pod of active source rock and extent of oil generation. Based on a buoyancy-drive model, the system was divided into seven secondary-migration catchments. Each catchment contains a part of the active pod of source rock from which it derives a petroleum charge, and this charge is confined to carrier beds and reservoirs within these catchments as accountable petroleum, petroleum losses, or undiscovered petroleum. A well-constrained catchment with no apparent erosional or leakage losses is used to determine an actual petroleum charge from accountable petroleum and residual migration losses. This actual petroleum charge is used to calibrate the other catchments in which erosional petroleum losses have occurred. Petroleum charges determined by laboratory pyrolysis are exaggerated relative to the actual petroleum charge. Rock-Eval charges are exaggerated by a factor of 4-14, and hydrouspyrolysis charges are exaggerated by a factor of 1.7. The actual petroleum charge provides a more meaningful material balance and more realistic estimates of petroleum losses and remaining undiscovered petroleum. The total petroleum charge determined for the New Albany-Chesterian system is 78 billion bbl, of which 11.4 billion bbl occur as a accountable in place petroleum, 9 billion bbl occur as residual migration losses, and 57.6 billion bbl occur as erosional losses. Of the erosional losses, 40 billion bbl

Flow of microemulsion through soil columns contaminated with asphaltic residue; Fluxo de microemulsoes atraves do solo contaminado com residuos asfalticos

Energy Technology Data Exchange (ETDEWEB)

Oliveira, Marcia C.K.; Oliveira, Jose F. [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Coordenacao dos Programas de Pos-graduacao de Engenharia (COPPE); Oliveira, Roberto C.G.; Gonzalez, Gazpar [PETROBRAS, Rio de Janeiro, RJ (Brazil). Centro de Pesquisas

2004-07-01

Nowadays, soil contamination with nonaqueous phase liquids (NAPLs) such as petroleum hydrocarbons is a major environmental problem. Significant efforts have been devoted to the development of processes to remediate sites contaminated with NAPLs. Unfortunately, most of the developed processes proved to be inefficient to remove the organic heavy fraction present in the NAPLs. Nevertheless, in our preliminary bench scale tests it was observed that, due to their high solubilization capacity and stability, microemulsions are able to remove organic heavy fractions like asphaltenes and resins, typically present in crude oils. The present work was dimensioned to evaluate, under up-flow condition, the performance of different microemulsions specially designed to remove asphaltenes fractions from soils using a column test set-up. The contaminant residual concentration was quantified by UV spectroscopy and the microemulsion efficiency determined using mass balance. The results showed that the microemulsions tested have a high capacity for removing asphaltenes fractions from contaminated soils. It was also observed that the predominant removal mechanism, solubilization or mobilization, depends essentially on the microemulsion's chemical formulation. Finally it was verified that microemulsion's formulations based on natural solvents compounds are also efficient for removing asphaltic residues. (author)

Taxation of petroleum companies possessing private information

International Nuclear Information System (INIS)

Osmundsen, P.

1995-01-01

For countries having petroleum resources, a common objective of the Ministry of Energy is to maximise the net total government take from the petroleum industry. Most models of petroleum taxation, assuming symmetric information, recommended neutral taxation. A royalty is not optimal in this case as it gives disincentives for extraction, causing too much of the reservoir to remain unexploited. Through the operating activities, however, the companies obtain private information about the costs. A low cost company may conceal its information by imitating a high cost company, and must therefore be given an economic compensation (information rent) to be induced to reveal its true costs. An optimal regulatory response to asymmetric information may involve royalties, as these enable the government to capture a larger fraction of the economic rent. 17 refs., 2 figs

Ozone using outlook for efficiency increasing of transportation and processing of high viscous petroleum raw materials

International Nuclear Information System (INIS)

Nadirov, N.K.; Zajkina, R.F.; Mamonova, T.B.

1997-01-01

Main types of oxidation reactions preceding during petroleum feedstock ozonization are generalized. The slight ozone high paraffin-content petroleum processing sites in shown on the example will make possible to rise the pipe transport efficiency and to increase the light fraction contents in petroleums. The prospects are discussed to application of ozone forming as a by-product of radiation-chemical facilities action for petroleum feedstock processing. (author)

The influence of dissolved petroleum hydrocarbon residues on natural phytoplankton biomass

Digital Repository Service at National Institute of Oceanography (India)

Shailaja, M.S.

on phytoplankton biomass varies depending on the nature rather than the quantity of petroleum hydrocarbons present. Culture studies with unialgal Nitzschia sp. in seawater collected from selected stations in the study area as well as in artificial seawater spiked...

[Study on the groundwater petroleum contaminant remediation by air sparging].

Science.gov (United States)

Wang, Zhi-Qiang; Wu, Qiang; Zou, Zu-Guang; Chen, Hong; Yang, Xun-Chang; Zhao, Ji-Chu

2007-04-01

The groundwater petroleum contaminant remediation effect by air sparging was investigated in an oil field. The results show that the soil geological situation has great influence on the air distribution, and the shape of air distribution is not symmetrical to the air sparging (AS) well as axis. The influence distance in the left of AS well is 6 m, and only 4 m in the right. The petroleum removal rate can reach 70% in the zone with higher air saturation, but only 40% in the zone with lower air saturation, and the average petroleum removal rate reaches 60% in the influence zone for 40 days continuous air sparging. The petroleum components in groundwater were analyzed by GC/MS (gas chromatogram-mass spectrograph) before and after experiments, respectively. The results show that the petroleum removal rate has relationship with the components and their properties. The petroleum components with higher volatility are easily removed by volatilization, but those with lower volatility are difficult to remove, so a tailing effect of lingering residual contaminant exists when the air sparging technology is adopted to treat groundwater contaminated by petroleum products.

How to prepare water accommodated fractions from petroleum hydrocarbons for use in aquatic toxicity testing - the basics

International Nuclear Information System (INIS)

Blenkinsopp, S.; Boileau, P.; Kyle, D.; Sergy, G.; Fingas, M.

1996-01-01

A method to prepare water accommodated fractions (WAFs) from petroleum products for use in toxicity testing, was introduced. In order to develop a repeatable protocol, a systematic study of a range of experimental variables was conducted. One semi-solid oil and six liquid oils were exposed to artificial seawater. Studies were also performed on three liquid oils exposed to freshwater. Low energy mixing and fluorinated Nalgene carboys was used to produce the WAFs. The mixing time depended on the oil type and loading rate. Individual loading rates were prepared for each concentration, because WAF composition is influenced by loading rate rather than serial dilution. An overview of the basic concepts of WAF preparation was described. A draft protocol for preparing WAFs from liquid and semi-solid oil was also described and results were summarized. 5 refs., 3 tabs., 6 figs

Petroleum supply monthly, December 1995: With data for October 1995

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-12-01

Data presented in the Petroleum Supply Monthly (PSM) describe the supply and disposition of petroleum products in the US and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the US (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the US. The tables and figures in the Summary Statistics section of the PSM present a time series of selected petroleum data on a US level. The Detailed Statistics tables of the PSM present statistics for the most current month available as well as year-to-date. In most cases, the statistics are presented for several geographic areas--the US (50 States and the District of Columbia), five PAD Districts, and 12 Refining Districts. At the US and PAD District level, the total volume and the daily rate of activities are presented. 16 figs., 6 tabs.

Bioremediation and reclamation of soil contaminated with petroleum oil hydrocarbons by exogenously seeded bacterial consortium: a pilot-scale study.

Science.gov (United States)

Mukherjee, Ashis K; Bordoloi, Naba K

2011-03-01

Spillage of petroleum hydrocarbons causes significant environmental pollution. Bioremediation is an effective process to remediate petroleum oil contaminant from the ecosystem. The aim of the present study was to reclaim a petroleum oil-contaminated soil which was unsuitable for the cultivation of crop plants by using petroleum oil hydrocarbon-degrading microbial consortium. Bacterial consortium consisting of Bacillus subtilis DM-04 and Pseudomonas aeruginosa M and NM strains were seeded to 20% (v/w) petroleum oil-contaminated soil, and bioremediation experiment was carried out for 180 days under laboratory condition. The kinetics of hydrocarbon degradation was analyzed using biochemical and gas chromatographic (GC) techniques. The ecotoxicity of the elutriates obtained from petroleum oil-contaminated soil before and post-treatment with microbial consortium was tested on germination and growth of Bengal gram (Cicer aretinum) and green gram (Phaseolus mungo) seeds. Bacterial consortium showed a significant reduction in total petroleum hydrocarbon level in contaminated soil (76% degradation) as compared to the control soil (3.6% degradation) 180 days post-inoculation. The GC analysis confirmed that bacterial consortium was more effective in degrading the alkane fraction compared to aromatic fraction of crude petroleum oil hydrocarbons in soil. The nitrogen, sulfur, and oxygen compounds fraction was least degraded. The reclaimed soil supported the germination and growth of crop plants (C. aretinum and P. mungo). In contrast, seeds could not be germinated in petroleum oil-contaminated soil. The present study reinforces the application of bacterial consortium rather than individual bacterium for the effective bioremediation and reclamation of soil contaminated with petroleum oil.

Environmental hazard and risk characterisation of petroleum substances: a guided "walking tour" of petroleum hydrocarbons.

Science.gov (United States)

Bierkens, Johan; Geerts, Lieve

2014-05-01

Petroleum substances are used in large quantities, primarily as fuels. They are complex mixtures whose major constituents are hydrocarbons derived from crude oil by distillation and fractionation. Determining the complete molecular composition of petroleum and its refined products is not feasible with current analytical techniques because of the huge number of molecular components. This complex nature of petroleum products, with their varied number of constituents, all of them exhibiting different fate and effect characteristics, merits a dedicated hazard and risk assessment approach. From a regulatory perspective they pose a great challenge in a number of REACH processes, in particular in the context of dossier and substance evaluation but also for priority setting activities. In order to facilitate the performance of hazard and risk assessment for petroleum substances the European oil company association, CONCAWE, has developed the PETROTOX and PETRORISK spreadsheet models. Since the exact composition of many petroleum products is not known, an underlying assumption of the PETROTOX and PETRORISK tools is that the behaviour and fate of a total petroleum substance can be simulated based on the physical-chemical properties of representative structures mapped to hydrocarbon blocks (HBs) and on the relative share of each HB in the total mass of the product. To assess how differing chemical compositions affect the simulated chemical fate and toxicity of hydrocarbon mixtures, a series of model simulations were run using an artificial petroleum substance, containing 386 (PETROTOX) or 160 (PETRORISK) HBs belonging to different chemical classes and molecular weight ranges, but with equal mass assigned to each of them. To this artificial petroleum substance a guided series of subsequent modifications in mass allocation to a delineated number of HBs belonging to different chemical classes and carbon ranges was performed, in what we perceived as a guided "walking tour

Development of a hybrid proximal sensing method for rapid identification of petroleum contaminated soils

Energy Technology Data Exchange (ETDEWEB)

Chakraborty, Somsubhra [Ramakrishna Mission Vivekananda University, Kolkata (India); Weindorf, David C., E-mail: david.weindorf@ttu.edu [Department of Plant and Soil Science, Texas Tech University, Lubbock, TX (United States); Li, Bin [Department of Experimental Statistics, Louisiana State University, Baton Rouge, LA (United States); Ali Aldabaa, Abdalsamad Abdalsatar [Desert Research Center, Cairo (Egypt); Ghosh, Rakesh Kumar [National Institute of Research on Jute and Allied Fibre Technology, Kolkata (India); Paul, Sathi; Nasim Ali, Md. [Ramakrishna Mission Vivekananda University, Kolkata (India)

2015-05-01

Using 108 petroleum contaminated soil samples, this pilot study proposed a new analytical approach of combining visible near-infrared diffuse reflectance spectroscopy (VisNIR DRS) and portable X-ray fluorescence spectrometry (PXRF) for rapid and improved quantification of soil petroleum contamination. Results indicated that an advanced fused model where VisNIR DRS spectra-based penalized spline regression (PSR) was used to predict total petroleum hydrocarbon followed by PXRF elemental data-based random forest regression was used to model the PSR residuals, it outperformed (R{sup 2} = 0.78, residual prediction deviation (RPD) = 2.19) all other models tested, even producing better generalization than using VisNIR DRS alone (RPD's of 1.64, 1.86, and 1.96 for random forest, penalized spline regression, and partial least squares regression, respectively). Additionally, unsupervised principal component analysis using the PXRF + VisNIR DRS system qualitatively separated contaminated soils from control samples. Capsule: Fusion of PXRF elemental data and VisNIR derivative spectra produced an optimized model for total petroleum hydrocarbon quantification in soils. - Highlights: • PXRF elemental data and VisNIR DRS spectra were correlated to soil TPH. • VisNIR + PSR was used to predict TPH followed by PXRF + RF to predict the residuals. • The fused model produced better results than other multivariate models tested.

[Chemical constituents from petroleum ether fraction of Swertia chirayita and their activities in vitro].

Science.gov (United States)

You, Rong-Rong; Chen, Xue-Qing; He, Dan-Dan; Huang, Chang-Gao; Jin, Yang; Qian, Shi-Hui; Ju, Jian-Ming; Fan, Jun-Ting

2017-10-01

The present work is to study the chemical constituents from petroleum ether fraction of Tibetan medicine Swertia chirayita by column chromatography and recrystallization. The structures were identified by physical and chemical properties and spectral data as swerchirin (1), decussatin (2), 1,8-dihydroxy-3,5,7-trimethoxyxanthone (3), 1-hydroxy-3,5,7,8-tetramethoxyxanthone (4), bellidifolin (5), 1-hydroxy-3, 7-dimethoxyxanthone (6), methylswertianin (7), 1-hydroxy-3,5-dimethoxyxanthone (8), erythrodiol (9), oleanolic acid (10), gnetiolactone (11), scopoletin (12), sinapaldehyde (13), syringaldehyde (14), and β-sitosterol (15). Compounds 3, 4, 9, 11-14 were isolated from S. chirayita for the first time. Compounds 9 and 12 were firstly isolated from the genus Swertia. The cytotoxic activities of compounds 1, 2, 5, 7 and 8 against human pancreatic cancer cell lines SW1990 and BxPC-3,and the protective effects of these compounds against hydrogen peroxide (H2O2)-induced oxidative stress in human endothelium-derived EA.hy926 were investigated in vitro. The results showed no obvious effect at the high concentration of 50 μmol•L⁻¹. Copyright© by the Chinese Pharmaceutical Association.

Direct soil contact values for ecological receptors exposed to weathered petroleum hydrocarbon (PHC) fraction 2.

Science.gov (United States)

Angell, Robin A; Kullman, Steve; Shrive, Emma; Stephenson, Gladys L; Tindal, Miles

2012-11-01

Ecological tier 1 Canada-wide standards (CWS) for petroleum hydrocarbon (PHC) fraction 2 (F2; >nC10-C16) in soil were derived using ecotoxicological assessment endpoints (effective concentrations [ECs]/lethal concentrations [LCs]/inhibitory concentrations, 25% [IC25s]) with freshly spiked (fresh) fine- and coarse-grained soils. These soil standards might be needlessly conservative when applied to field samples with weathered hydrocarbons. The purpose of the present study was to assess the degradation and toxicity of weathered PHC F2 in a fine-grained soil and to derive direct soil contact values for ecological receptors. Fine-grained reference soils were spiked with distilled F2 and weathered for 183 d. Toxicity tests using plants and invertebrates were conducted with the weathered F2-spiked soils. Endpoint EC/IC25s were calculated and used to derive soil standards for weathered F2 in fine-grained soil protective of ecological receptors exposed via direct soil contact. The values derived for weathered F2 were less restrictive than current ecological tier 1 CWS for F2 in soil. Copyright © 2012 SETAC.

New technology for recovering residual metals from nonmetallic fractions of waste printed circuit boards.

Science.gov (United States)

Zhang, Guangwen; He, Yaqun; Wang, Haifeng; Zhang, Tao; Wang, Shuai; Yang, Xing; Xia, Wencheng

2017-06-01

Recycling of waste printed circuit boards is important for environmental protection and sustainable resource utilization. Corona electrostatic separation has been widely used to recycle metals from waste printed circuit boards, but it has poor separation efficiency for finer sized fractions. In this study, a new process of vibrated gas-solid fluidized bed was used to recycle residual metals from nonmetallic fractions, which were treated using the corona electrostatic separation technology. The effects of three main parameters, i.e., vibration frequency, superficial air flow velocity, and fluidizing time on gravity segregation, were investigated using a vibrating gas-solid fluidized bed. Each size fraction had its own optimum parameters. Corresponding to their optimal segregation performance, the products from each experiment were analyzed using an X-ray fluorescence (XRF) and a scanning electron microscope (SEM) equipped with an energy dispersive spectrometer (EDS). From the results, it can be seen that the metal recoveries of -1+0.5mm, -0.5+0.25mm, and -0.25mm size fractions were 86.39%, 82.22% and 76.63%, respectively. After separation, each metal content in the -1+0.5 or -0.5+0.25mm size fraction reduced to 1% or less, while the Fe and Cu contents are up to 2.57% and 1.50%, respectively, in the -0.25mm size fraction. Images of the nonmetallic fractions with a size of -0.25mm indicated that a considerable amount of clavate glass fibers existed in these nonmetallic fractions, which may explain why fine particles had the poorest segregation performance. Copyright © 2017 Elsevier Ltd. All rights reserved.

Bioremediation of petroleum hydrocarbons in soil environments. Report No. EE-141

Energy Technology Data Exchange (ETDEWEB)

Rowell, M J; Ashworth, J; Qureshi, A A

1992-01-01

The bioremediation of petroleum hydrocarbons in soil environments was reviewed by means of a literature survey and also through discussions with workers in relevent disciplines. This report discusses both the impacts of hydrocarbons on soil and a range of methods available to assist in the decomposition by soil microorganisms. The range of petroleum-based materials considered includes conventional and synthetic crude oils, refined oils, oily sludges, asphalts and bitumens, drilling mud residues, creosote tars and some pesticides.

Petroleum marketing monthly: September 1996, with data for June 1996

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-09-01

The Petroleum Marketing Monthly provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. Detailed statistics for crude oil, including the price of imported crude oil by country of origin, by gravity, and by crude stream. To aid the reader in determining the market changes, the majority of the tables show data for the report month and previous months for the current year, and the report month for the previous year. 7 figs., 50 tabs.

Microbial Physiology of the Conversion of Residual Oil to Methane: A Protein Prospective

Science.gov (United States)

Morris, Brandon E. L.; Bastida-Lopez, Felipe; von Bergen, Martin; Richnow, Hans-Hermann; Suflita, Joseph M.

2010-05-01

Traditional petroleum recovery techniques are unable to extract the majority of oil in most petroliferous deposits. The recovery of even a fraction of residual hydrocarbon in conventional reserves could represent a substantive energy supply. To this end, the microbial conversion of residual oil to methane has gained increasing relevance in recent years [1,2]. Worldwide demand for methane is expected to increase through 2030 [3], as it is a cleaner-burning alternative to traditional fuels [4]. To investigate the microbial physiology of hydrocarbon-decomposition and ultimate methanogenesis, we initiated a two-pronged approach. First, a model alkane-degrading sulfate-reducing bacterium, Desulfoglaeba alkanexedens, was used to interrogate the predominant metabolic pathway(s) differentially expressed during growth on either n-decane or butyrate. A total of 81 proteins were differentially expressed during bacterial growth on butyrate, while 100 proteins were unique to the alkane-grown condition. Proteins related to alkylsuccinate synthase, or the homologous 1-methyl alkylsuccinate synthase, were identified only in the presence of the hydrocarbon. Secondly, we used a newly developed stable isotope probing technique [5] targeted towards proteins to monitor the flux of carbon through a residual oil-degrading bacterial consortium enriched from a gas-condensate contaminated aquifer [1]. Combined carbon and hydrogen stable isotope fractionation identified acetoclastic methanogenesis as the dominant process in this system. Such findings agree with the previous clone library characterization of the consortium. Furthermore, hydrocarbon activation was determined to be the rate-limiting process during the net conversion of residual oil to methane. References 1. Gieg, L.M., K.E. Duncan, and J.M. Suflita, Bioenegy production via microbial conversion of residual oil to natural gas. Appl Environ Micro, 2008. 74(10): p. 3022-3029. 2. Jones, D.M., et al., Crude-oil biodegradation via

Characterization of Petroleum Hydrocarbons in Post-Burn Crude Oil ...

African Journals Online (AJOL)

In the Niger delta, crude oil spilled soils are burned as a means of decontaminating the impacted soils. Gas chromatography - flame ionization detector (GCFID) analyses were performed on oil residues extracted from burnt spilled oil soil samples to facilitate detailed chemical composition and characterization of petroleum ...

Nickel and vanadium extraction from the Syrian petroleum coke

International Nuclear Information System (INIS)

Shlewit, H.; Alibrahim, M.

2007-01-01

Syrian petroleum coke samples were characterized and submitted for salt-roasting treatment in electric furnace to evaluate the convenience of this procedure for the extraction of the vanadium, nickel and sulfur from coke. Both solution and solid residue remaining after salt roasting were separated by filtration and were analyzed for vanadium, nickel and sulfur. The solution was analyzed by UV-Visible spectroscopy for vanadium and nickel and gravimetrically for sulfur. The solid residue and the untreated samples of petroleum coke were analyzed by XRF spectrometry. Results showed that more than 90% of sulfur and 60% of vanadium could be extracted by salt roasting treatment. An alternative procedure has been suggested, in which, more than 80% of sulfur and small percentage of vanadium can be leached by 0.75 M of Na 2 CO 3 solution at 70-80 Co. Vanadium was selectively extracted by DEHPA/TBP from the loaded leached solution. The extraction procedure flowsheet was also suggested. (authors)

Coaxial Sensors For Broad-Band Complex Permittivity Measurements of Petroleum Fluids

Energy Technology Data Exchange (ETDEWEB)

Folgeroe, K.

1996-12-31

This doctoral thesis verifies that dielectric spectroscopy and microwave permittivity measurements can be used to characterize petroleum liquids. It concentrates on developing sensors for three potential industrial applications: quality characterization of crude oil and petroleum fractions, monitoring of gas-hydrate formation in water-in-oil emulsions, and determination of water-content in thin liquid layers. The development of a permittivity measurement system for crude oil and petroleum fractions is described. As black oils have low dielectric constant and loss, the system must be very sensitive in order to measure the dielectric spectra and to distinguish oils of different permittivity. Such a system was achieved by combining impedance and scattering parameter measurements with appropriate permittivity calculation methods. The frequency range from 10 kHz to 6 GHz was found convenient for observing the main dispersion of the oils. All the oils had dielectric constants between 2.1 and 2.9 and dielectric loss below 0.01. The oils studied were samples of the feedstock for the cracker and coke processes at a petroleum refinery. This verifies that dielectric spectroscopy is a potential technique for on-line quality monitoring of the feedstock at petroleum refineries. Gas hydrates may cause major problems like clogging of pipelines. Dielectric spectroscopy is proposed as a means of monitoring the formation of gas hydrates in emulsions. It is found that open-ended coaxial probes fulfill the sensitivity requirements for such sensors. 312 refs., 87 figs., 20 tabs.

Petroleum supply monthly, July 1999, with data for May 1999

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-07-01

The Petroleum Supply Monthly (PSM) is one of a family of four petroleum supply publications produced by the Petroleum Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the US and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the US (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the US. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics. The Detail Statistics tables of the PSM present statistics for the most current month available as well as year-to-date. In most cases, the statistics are presented for several geographic areas--the US (50 States and the District of Columbia), five PAD Districts, and 12 Refining Districts. At the US and PAD District level, the total volume and the daily rate of activities are presented. The statistics are developed from monthly survey forms submitted by respondents to the EIA and from data provided from other sources.

Petroleum supply monthly, April 1998, with data for February 1998

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-04-01

The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. Data presented in the PSM describe the supply and disposition of petroleum products in the US and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the US (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the US. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics. The tables and figures in the Summary Statistics section of the PSM present a time series of selected petroleum data on a US level. Most time series include preliminary estimates for one month based on the Weekly Petroleum Supply Reporting System; statistics based on the most recent data from the Monthly Petroleum Supply Reporting System (MPSRS); and statistics published in prior issues of the PSM and PSA. The Detailed Statistics tables of the PSM present statistics for the most current month available as well as year-to-date. In most cases, the statistics are presented for several geographic areas--the US (50 States and District of Columbia), 5 PAD Districts and 12 Refining Districts. 16 figs., 56 tabs.

CG/MS quantitation of diamondoid compounds in crude oils and petroleum products

International Nuclear Information System (INIS)

Yang, C.; Wang, Z.D.; Hollebone, B.P.; Fingas, M.; Peng, X.; Landriault, M.

2006-01-01

Diamondoids are a class of saturated hydrocarbons that consist of 3-dimensionally fused cyclohexane rings. Diamondoid compounds in petroleum are the result of carbonium ion rearrangements of cyclic precursors on clay superacids in the source rock during oil generation. They are considered to be a problem due to their deposition during production of reservoir fluids and transportation of natural gas, gas condensates and light crude oils. At high concentrations, and with changes in pressure and temperature, diamondoid compounds can segregate out of reservoir fluids during production. Environmental scientists have considered fingerprinting the diamondoid hydrocarbons as a forensic method for oil spill studies. Since diamondoid compounds are thermodynamically stable, they have potential applications in oil-source correlation and differentiation for cases where traditional biomarker terpanes and steranes are absent because of environmental weathering or refining of petroleum products. Although there is increased awareness of possible use of diamondoid compounds for source identification, there is no systematic approach for using these compounds. Quantitative surveys of the abundances of diamondoids are not available. Therefore, this study developed a reliable analytical method for quantitative diamondoid analysis. Gas chromatography/mass spectrometry (GC/MS) was used to quantitatively determine diamondoid compounds (adamantane, diamantane and their alkylated homologues) in 14 fresh crude oils and 23 refined petroleum products, including light and mid-range distillate fuels, residual fuels and lubricating oils collected from different sources. Results were compared with 2 types of biomarker compounds in oil saturated hydrocarbon fractions. Several diagnostic ratios of diamondoids were developed based on their concentrations. Their potential use for forensic oil spill source identification was evaluated. 24 refs., 8 tabs., 4 figs

An experimental investigation of geochromatography during secondary migration of petroleum performed under subsurface conditions with a real rock

Directory of Open Access Journals (Sweden)

Larter Steve

2000-10-01

Full Text Available An understanding of the size of petroleum secondary migration systems is vital for successful exploration for petroleum reserves. Geochemists have suggested that compositional fractionation of petroleum accompanying the migration process (geochromatography can potentially be used to infer distances petroleum may have travelled and the ratio of oil in the reservoir to that lost in the carrier. To date, this has been attempted by measuring concentrations and distributions of specific steranes, and aromatic oxygen and nitrogen compounds in reservoired oils which have been proposed to respond to migration rather than to source maturity or other effects. We report here an experiment involving oil migration through an initially water wet siltstone under realistic subsurface carrier bed or reservoir conditions (48 MPa, 70°C where source facies and maturity effects are eliminated. We show that geochromatography does indeed occur even for initially water-saturated rocks and that the migration fractionations observed for alkylcarbazoles, benzocarbazoles and alkylphenols are very similar to those seen in field data sets. In contrast, sterane based migration parameters show no compositional fractionation under these conditions.

PLS models for determination of SARA analysis of Colombian vacuum residues and molecular distillation fractions using MIR-ATR

Directory of Open Access Journals (Sweden)

Jorge A. Orrego-Ruiz

2014-06-01

Full Text Available In this work, prediction models of Saturates, Aromatics, Resins and Asphaltenes fractions (SARA from thirty-seven vacuum residues of representative Colombian crudes and eighteen fractions of molecular distillation process were obtained. Mid-Infrared (MIR Attenuated Total Reflection (ATR spectroscopy in combination with partial least squares (PLS regression analysis was used to estimate accurately SARA analysis in these kind of samples. Calibration coefficients of prediction models were for saturates, aromatics, resins and asphaltenes fractions, 0.99, 0.96, 0.97 and 0.99, respectively. This methodology permits to control the molecular distillation process since small differences in chemical composition can be detected. Total time elapsed to give the SARA analysis per sample is 10 minutes.

Method for quantifying the fate of petroleum in the environment

International Nuclear Information System (INIS)

Mills, M.A.; McDonald, T.J.; Bonner, J.S.; Simon, M.A.; Autenrieth, R.L.

1999-01-01

Petroleum is a complex mixture of a wide range of hydrocarbon and non-hydrocarbon compounds of various physical and chemical properties. In recent years, the research on the fate of petroleum in the environment has required analytical methods that can provide more detailed information on the components of petroleum than traditional standard methods. The analytical method presented for aqueous, sediment, and soil samples provides several levels of information on petroleum in the environment. The Total Extractable Materials (TEM) analysis provides a gross measure of petroleum in the environment using methylene chloride extraction and gravimetric analysis. Gross composition analysis separates the methylene chloride extract into a saturate hydrocarbon, an aromatic hydrocarbon, and a polar fraction each measured gravimetrically. In contrast, the target compound analysis provides a detailed measure by GC-MS of 62 specific compounds. Normalization to the conservative compound, 17α, 21β-(H)Hopane, is incorporated into the method to reduce the effects of sample and site heterogeneity. Quality control and quality assurance procedures are integral parts of these analyses to assure the validity of the resulting data. (author)

Characterization of catalytically hydrotreated coal liquid produced by solvolytic liquefaction in petroleum asphalt

Energy Technology Data Exchange (ETDEWEB)

Mochida, I.; Oishi, T.; Korai, Y.; Fujitsu, H.; Takeshita, K.

1983-03-01

A hydrotreated coal liquid produced by solvolytic liquefaction of a feed originally consisting of 66% petroleum asphalt and 34% coal liquid was characterized. The hydrotreatment was carried out over a Co-Mo catalyst in order to upgrade moderately and selectively the coal-derived fraction. The present process was found very effective to depolymerize rather selectively the coal-derived fraction, originally benzene insoluble, to be soluble in benzene in the dominant presence of petroleum asphalt, while 20% of the asphalt was converted to be distillable with ..cap alpha..-methylnaphthalene (the hydrotreatment solvent). Structural analyses of the fractions before and after hydrotreatment were compared to reveal what kinds of chemical reactions had taken place during hydro treatment. The major reactions of the coal derived fraction are hydrodeoxygenation and hydrodealkylation, both of which are effective for depolymerization. No significant hydrogenation on aromatic rings was observed. Hydrotreated liquid was further pyrolyzed to obtain oils and cokes of high quality. (14 refs.)

Analysis of low-temperature tar fractions

Energy Technology Data Exchange (ETDEWEB)

Kikkawa, S; Yamada, F

1952-01-01

A preliminary comparative study was made on the applicability of the methods commonly used for the type analysis of petroleum products to the low-temperature tar fractions. The usability of chromatography was also studied.

Viscosity Prediction for Petroleum Fluids Using Free Volume Theory and PC-SAFT

Science.gov (United States)

Khoshnamvand, Younes; Assareh, Mehdi

2018-04-01

In this study, free volume theory ( FVT) in combination with perturbed-chain statistical associating fluid theory is implemented for viscosity prediction of petroleum reservoir fluids containing ill-defined components such as cuts and plus fractions. FVT has three adjustable parameters for each component to calculate viscosity. These three parameters for petroleum cuts (especially plus fractions) are not available. In this work, these parameters are determined for different petroleum fractions. A model as a function of molecular weight and specific gravity is developed using 22 real reservoir fluid samples with API grades in the range of 22 to 45. Afterward, the proposed model accuracy in comparison with the accuracy of De la Porte et al. with reference to experimental data is presented. The presented model is used for six real samples in an evaluation step, and the results are compared with available experimental data and the method of De la Porte et al. Finally, the method of Lohrenz et al. and the method of Pedersen et al. as two common industrial methods for viscosity calculation are compared with the proposed approach. The absolute average deviation was 9.7 % for free volume theory method, 15.4 % for Lohrenz et al., and 22.16 for Pedersen et al.

Enantiomeric fraction and isomeric composition to assess sources of DDT residues in soils.

Science.gov (United States)

Bosch, Carme; Grimalt, Joan O; Fernández, Pilar

2015-11-01

Chiral pesticides such as o,p'-DDT can undergo enantioselective microbial degradation in soil. Hence, the enantiomeric fraction (EF) of o,p'-DDT was used as an approach to assess potential recent inputs of DDT in the lower part of the Ebro River basin (NE Spain), a region heavily impacted by agricultural and industrial activities, including a dicofol production and a chloro-alkali plants. The EFs of five out of nineteen soils were not different from the racemic value (0.505±0.010), confirming that the Ebro River and some of its tributaries, Segre and Cinca rivers, transported fresh DDT residues despite its ban in Spain during the 90 s. o,p'-DDT/p,p'-DDT ratios in soils suggest that recent use of technical DDT and/or DDT-contaminated dicofol may be responsible for the fresh DDT inputs in the Segre River, while in the Ebro River, they indicate a dominant contribution of technical DDT, likely related to the residues accumulated by the chloro-alkali plant discharges. Copyright © 2015 Elsevier Ltd. All rights reserved.

Study of variation grain size in desulfurization process of calcined petroleum coke

Science.gov (United States)

Pintowantoro, Sungging; Setiawan, Muhammad Arif; Abdul, Fakhreza

2018-04-01

Indonesia is a country with abundant natural resources, such as mineral mining and petroleum. In petroleum processing, crude oil can be processed into a source of fuel energy such as gasoline, diesel, oil, petroleum coke, and others. One of crude oil potentials in Indonesia is petroleum coke. Petroleum coke is a product from oil refining process. Sulfur reducing process in calcined petroleum cokes can be done by desulfurization process. The industries which have potential to become petroleum coke processing consumers are industries of aluminum smelting (anode, graphite block, carbon mortar), iron riser, calcined coke, foundry coke, etc. Sulfur reducing process in calcined petroleum coke can be done by thermal desulfurization process with alkaline substance NaOH. Desulfurization of petroleum coke process can be done in two ways, which are thermal desulfurization and hydrodesulphurization. This study aims to determine the effect of various grain size on sulfur, carbon, and chemical bond which contained by calcined petroleum coke. The raw material use calcined petroleum coke with 0.653% sulfur content. The grain size that used in this research is 50 mesh, then varied to 20 mesh and 100 mesh for each desulfurization process. Desulfurization are tested by ICP, UV-VIS, and FTIR to determine levels of sulfur, carbon, chemical bonding and sulfur dissolved water which contained in the residual washing of calcined petroleum coke. From various grain size that mentioned before, the optimal value is on 100 mesh grain size, where the sulfur content in petroleum coke is 0.24% and carbon content reaches the highest level of 97.8%. Meanwhile for grain size 100 mesh in the desulfurization process is enough to break the chemical bonds of organic sulfur in petroleum coke.

Industrial rag cleaning process for the environmentally safe removal of petroleum-based solvents

International Nuclear Information System (INIS)

Fierro, J.V.

1993-01-01

A process for the cleaning of industrial rags contaminated with environmentally unsafe petroleum-based solvent is described, comprising the step of: (a) placing a load of the industrial rags in a mechanically driven rotary drum; (b) revolving the drum at a high speed sufficient to physically extract liquid petroleum-based solvent contaminate from the industrial rags; (c) routing the extracted petroleum-based solvent contaminate from the rotary drum to a waste solvent collection line for environmentally safe disposal; (d) revolving the rotary drum to cause a tumbling of the industrial rags while maintaining the temperature within the drum at below the flash point of the petroleum-based solvent; (e) intermittently forcing cold air and hot air through the rotary drum to vaporize solvent from the industrial rags; (f) routing the vaporized petroleum-based solvent contaminant from the rotary drum to a condenser wherein the petroleum-based solvent contaminate is condensed and thereafter further routing said condensed solvent to a waste collection line for environmentally safe disposal; and (g) cleaning the industrial rags in the presence of a dry cleaning solvent to remove residual petroleum-based solvents and soil

On the comparison of perturbation-iteration algorithm and residual power series method to solve fractional Zakharov-Kuznetsov equation

Science.gov (United States)

Şenol, Mehmet; Alquran, Marwan; Kasmaei, Hamed Daei

2018-06-01

In this paper, we present analytic-approximate solution of time-fractional Zakharov-Kuznetsov equation. This model demonstrates the behavior of weakly nonlinear ion acoustic waves in a plasma bearing cold ions and hot isothermal electrons in the presence of a uniform magnetic field. Basic definitions of fractional derivatives are described in the Caputo sense. Perturbation-iteration algorithm (PIA) and residual power series method (RPSM) are applied to solve this equation with success. The convergence analysis is also presented for both methods. Numerical results are given and then they are compared with the exact solutions. Comparison of the results reveal that both methods are competitive, powerful, reliable, simple to use and ready to apply to wide range of fractional partial differential equations.

Soil washing and post-wash biological treatment of petroleum hydrocarbon contaminated soils

OpenAIRE

Bhandari, Alok

1992-01-01

A laboratory scale study was conducted to investigate the treatability of petroleum contaminated soils by soil washing and subsequent biological treatment of the different soil fractions. In addition to soils obtained from contaminated sites, studies were also performed on soils contaminated in the laboratory. Soil washing was performed using a bench-scale soil washing system. Washing was carried out with simultaneous fractionation of the bulk soil into sand, silt and clay fractions. Cl...

Comparative dermal carcinogenesis of shale and petroleum-derived distillates.

Science.gov (United States)

Clark, C R; Walter, M K; Ferguson, P W; Katchen, M

1988-03-01

Ten test materials derived from petroleum or hydrotreated shale oils were applied 3 times/week for up to 105 weeks to the shaved skin of 25 male and 25 female C3H/HeN mice per group. Mineral oil and benzo(a) pyrene (0.15%) were control materials. Clinical observations were recorded during the study. At death, histopathologic examination was conducted on skin, internal organs and any gross lesions. Exposures to some materials were ended midway in the study due to severe irritation. Chronic toxicity of all materials was limited to inflammatory and degenerative skin changes. Significant increases over control incidence of skin tumors (squamous cell carcinoma and fibrosarcoma) occurred with both petroleum and shale-derived naphtha (21%, 50%), Jet A (26%, 28%), JP-4 (26%, 50%), and crude oils (84%, 54%). Severely hydrotreated shale oil and petroleum and shale-derived diesel distillates were not considered tumorigenic. Results indicate that toxicity of comparable petroleum and shale-derived fractions was qualitatively similar and confirm earlier findings that hydrotreating reduces or eliminates carcinogenicity of raw shale oil.

Application of the Salmonella mutagenicity assay and determination of polycyclic aromatic hydrocarbons in workplaces exposed to petroleum pitch and petroleum coke

Energy Technology Data Exchange (ETDEWEB)

Monarca, S; Pasquini, R; Sforzolini, G S; Viola, V; Fagioli, F

1982-02-01

Workplaces of an Italian carbon electrode factory, exposed to petroleum pitch and petroleum coke, were studied using a coupled chemical and biological approach to evaluate occupational mutagenic/carcinogenic hazards. Analytical procedures for the determination of polycyclic aromatic hydrocarbons (PAH) and Salmonella/microsome mutagenicity tests were performed on both industrial ingredients and airborne particulate matter of the working environment, after fractionating by sequential Soxhlet extractions with four organic solvents of increasing polarity. The results showed: the presence of extraordinarily high PAH contents in the benzene extracts of petroleum pitch and of airborne particulate samples, in correlation with very high indirect (after metabolic activation) mutagenic responses of benzene extracts with strain TA98; very high indirect mutagenic responses in the other extracts of the airborne particulate samples; the production during the processing at high temperatures of directly acting mutaggens which were absent in the starting materials and their release in the air of workplaces. The comparison of chemical analytical and mutagenicity data has proved to be an interesting approach for better defining the relative health hazards due to occupational exposure to potentially mutagenic/carcinogenic petroleum products.

Toxicity of oils and petroleum hydrocarbons to estuarine crustaceans

Energy Technology Data Exchange (ETDEWEB)

Tatem, H.E. (Army Engineer Waterways Experiment Station, Vicksburg, MS); Cox, B.A.; Anderson, J.W.

1978-04-01

Bioassay experiments with various life stages of three estuarine shrimp and soluble petroleum hydrocarbons (PH) revealed residual Bunker C oil and refined No. 2 fuel oil to be more toxic than two crude oils tested. Larvae of Palaemonetes pugio were slightly more sensitive to the PH than adults, while young penaeid shrimp were shown to be more resistant than older, larger individuals. Shrimp exposed to PH in conjunction with temperature and salinity changes were more susceptible to the PH. Some common aromatic and diaromatic PH, including three naphthalene compounds, were utilized in bioassays. Naphthalenes were highly toxic. The toxicity of petroleum products is closely related to aromatic hydrocarbon content, especially the naphthalenes and related hydrocarbons.

The role of the national petroleum company in petroleum development market

Energy Technology Data Exchange (ETDEWEB)

Lee, B J [Korea Energy Economics Institute, Euiwang (Korea, Republic of)

1997-08-01

The present century started with the creation of national petroleum companies, and it ends with those national petroleum companies exerting various types of efforts to increase the efficiency of their management. Especially, the efforts of these national petroleum companies are ever intensifying to adapt to new trends in the world petroleum market such as intensified competition, ever-deepening price unstableness, separation of structure between upstream and downstream portions, rapid development of petroleum development technologies, change of political systems and the demise of national borders, ever-increasing consciousness of environmental preservation, etc. Korea cannot be exempt from management rationalization efforts of national petroleum companies. Especially, Korea established its own national petroleum company in order to actively deal with these as its supply system is very weak. Therefore, the national petroleum company should create as many successful petroleum development businesses by actively carrying out petroleum development businesses domestically and overseas in order to establish a stable supply system of petroleum and to support the petroleum development businesses of civilian enterprises more effectively. The national petroleum company must, first of all, replace the bureaucracy with entrepreneurship. Esp., in order to enhance the efficiency of management, short- term outcome should not be emphasized over long-term tenure of petroleum development businesses, and excessive interference of government on the national petroleum company should be excluded. The entrepreneurship of the national petroleum company should be pursued in Positive-sum way, and its public image should be actively promoted through this. 35 refs., 11 figs., 32 tabs.

The use of polynuclear aromatic hydrocarbon (PAH) alkyl homologues in determining petroleum source identification and weathering

International Nuclear Information System (INIS)

Brown, J.S.; Boehm, P.D.; Sauer, T.C.; Wong, W.M.C.

1993-01-01

Techniques utilizing double ratio plots of selected polynuclear aromatic hydrocarbon (PAH) alkyl homologues were used to identify and distinguish crude oils and refined petroleum products from each other and to distinguish petroleum sources in complex pollutant regimes. Petroleum samples were fractionated by high performance liquid chromatography (HPLC) into saturated and aromatic (PAH) hydrocarbon fractions. The saturated hydrocarbon fractions were then analyzed by gas chromatography/flame ionization detection (GC/FID) to obtain a resolved/unresolved alkane fingerprint of each oil. The aromatic fractions of the oils were analyzed by gas chromatography/mass spectrometry (GC/MS) for PAH and selected alkyl homologues. Comparisons of the saturated hydrocarbon fingerprints indicated that some oils were indistinguishable based on the alkane fingerprint alone. Another double ratio plot of the alkyl chrysenes and alkyl dibenzothiophenes was effective in establishing the weathering of oil in environmental samples which were processed using the same analytical techniques, since the dibenzothiophenes are degraded more rapidly than the chrysenes. The application of selected ratios in oil spill source identification in complex environmental samples from Suisin Bay California and Boston Harbor are discussed. The use of ratios to measure the extent of weathering in oil spill samples from Prince William Sound and the Gulf of Alaska is examined

Surface active agents from Egyptian petroleum distillates

Energy Technology Data Exchange (ETDEWEB)

Kassem, T.M.

Kerosene and solar distillates from local crude petroleum 'Morgan' were fractionated. These fractions were refined with oleum and then distilled. The normal paraffins were separated from the refined fractions by the urea adduction technique. These paraffin cuts were subjected to 50% chlorination and the obtained monochlorinated paraffins were used in the synthesis of alkylbenzenes and alkyldiphenyls which were converted to anionic surfactants by sulphonation with 95% sulphuric acid. The sulphonyl chlorides of alkylbenzenes and of alkyldiphenyls were prepared and then converted to the corresponding sulphonamides. The prepared sulphonamides were then processed to nonionic surfactants through condensation with ethylene oxide. The ethoxylates were sulphated with chlorosulphonic acid and phosphated with phosphorus pentoxide to anionic surfactants. The surface active properties and the biodegradability of all the prepared surfactants were determined.

Crude petroleum

International Nuclear Information System (INIS)

1990-01-01

Crude petroleum statistics by country of production, export values and import values from 1983 to 1988 are given. Table A.1 of the Annex includes free market prices and price indices for crude petroleum based on average of Dubai, United Kingdom Brent and Alaska N Slope crude prices (price expressed in dollars/barrel). The data sources are: Crude petroleum United Nations Statistical Office; OPEC Annual Statistical Bulletin, and Petroleum Economist. For trade the sources of data are: National trade statistics; United Nations international trade statistics; International Moneytary Fund (IMF); Organization of the Petroleum Exporting Countries (OPEC); UNCTAD secretariat estimates. Tabs

Petroleum

International Nuclear Information System (INIS)

Anon.

2000-01-01

Here are gathered the results of the year 1999 concerning the petroleum industry in France ('UFIP' data), the market quotations of crude oil, the prices of fuels in France and in Portugal and some news about the petroleum industry in Algeria (privatization, exploration-offshore, repurchase), in Iraq (exports, contracts with foreign companies), in Russian Federation (petroleum pipelines and oil ports constructions) and in Chad (production sharing, offshore sites discoveries). (O.M.)

Total petroleum hydrocarbons: Characterization of physico-chemical behaviour and risks

Energy Technology Data Exchange (ETDEWEB)

Gemoets, J.; Lookman, R.; Vanermen, G.; Houtven, D. van; Bertels, D.; Weltens, R.; Cornelis, C. [VITO, Mol (Belgium); Vries, P. de; Sterren, G. van der; Alphenaar, A. [TTE, Deventer (Netherlands)

2003-07-01

Several methods are available for the characterization of petroleum hydrocarbons. Recently, the TPHCWG (Total Petroleum Hydrocarbon Criteria Working Group) developed a method based upon a silica column separation of aromatics and aliphatics and a GC-FID subdivision into equivalent-carbon fractions (EC) ('TPH-method'). Within NOBIS (Dutch Research program Biological I-situ Remediation), another method was developed based upon an equilibrium-experiment of the oil-polluted soil with water (column recirculation), which was further developed by TTE ('TTE-method'). This method uses measured water solubilities of individual oil components and GC-retention times yielding a subdivision of the hydrocarbons into compound classes. The present study aims at a verification (reproducibility; accuracy) and optimization of both methods and a critical review on the relevance of the proposed fractions for the prediction of human health risks. Two 'umpire' methods were selected for reference: GS-MS in full scan mode and liquid state NMR. (orig.)

Application of the salmonella mutagenicity assay and determination of polycyclic aromatic hydrocarbons in workplaces exposed to petroleum pitch and petroleum coke

Energy Technology Data Exchange (ETDEWEB)

Monarca, S; Pasquini, R; Sforzolini, G S; Fagioli, F; Viola, V

1982-02-01

Workplaces of an Italian carbon electrode factory, exposed to petroleum pitch and petroleum coke, were studied using a coupled chemical and biological approach to evaluate occupational mutagenic/carcinogenic hazards. Analytical procedures for the determination of polycyclic aromatic hydrocarbons (PAH) and Salmonella/microsome mutagenicity tests were performed on pitch and coke and airborne particulate matter of the working environment, after fractionating by sequential Soxhlet extractions with four organic solvents of increasing polarity (benzene, chloroform, methanol and acetone). The results showed: (a) the presence of extraordinarily high PAH (carcinogenic and noncarcinogenic) contents in the benzene extracts of petroleum pitch (3.6 wt% of total PAH) and of airborne particulate samples (up to 0.35 wt% of total PAH), in correlation with very high indirect mutagenic responses of benzene extracts; (b) very high indirect mutagenic responses in the other extracts of the airborne particulate samples; (c) the production during the processing at high temperatures of directly acting mutagens which were absent in the starting materials and their release in the air of workplaces. The comparison of chemical analytical and mutagenicity data has proved to be an interesting approach for better defining the relative health hazards due to occupational exposure to potentially mutagenic/carcinogenic petroleum products.

Sample handling and contamination encountered when coupling offline normal phase high performance liquid chromatography fraction collection of petroleum samples to Fourier transform ion cyclotron resonance mass spectrometry.

Science.gov (United States)

Oro, Nicole E; Whittal, Randy M; Lucy, Charles A

2012-09-05

Normal phase high performance liquid chromatography (HPLC) is used to separate a gas oil petroleum sample, and the fractions are collected offline and analyzed on a high resolution Fourier Transform Ion Cyclotron Resonance Mass Spectrometer (FT-ICR MS). The separation prior to MS analysis dilutes the sample significantly; therefore the fractions need to be prepared properly to achieve the best signal possible. The methods used to prepare the HPLC fractions for MS analysis are described, with emphasis placed on increasing the concentration of analyte species. The dilution effect also means that contamination in the MS spectra needs to be minimized. The contamination from molecular sieves, plastics, soap, etc. and interferences encountered during the offline fraction collection process are described and eliminated. A previously unreported MS contamination of iron formate clusters with a 0.8 mass defect in positive mode electrospray is also described. This interference resulted from the stainless steel tubing in the HPLC system. Contamination resulting from what has tentatively been assigned as palmitoylglycerol and stearoylglycerol was also observed; these compounds have not previously been reported as contaminant peaks. Copyright © 2012 Elsevier B.V. All rights reserved.

Characterization of residual oils for biodiesel production

Directory of Open Access Journals (Sweden)

Edmilson Antonio Canesin

2014-01-01

Conclusions: The obtained results suggesting that it is possible to take advantage of these residues for biodiesel production as the obtained products were approved according to the rules established by the National Association of Petroleum (ANP; the bovine samples were the exception regarding moisture and acidity.

Short- and long-run adjustments in U.S. petroleum consumption

International Nuclear Information System (INIS)

Huntington, Hillard G.

2010-01-01

Long-run adjustments in petroleum consumption are not only larger than short-run adjustments. They may also be motivated by entirely different price events. This analysis shows that new price peaks have both short-run and long-run consumption responses, a result that is starkly different than price changes that track previous price paths. It also establishes significant trend effects where gasoline and residual fuel oil consumption decline over time. The analysis explores these adjustments by establishing long-run cointegrating relationships for different petroleum product groupings. An important implication is that price increases above historical levels may be providing substantially greater incentives for significant long-run demand adjustments than would be the case otherwise. (author)

Short- and long-run adjustments in U.S. petroleum consumption

Energy Technology Data Exchange (ETDEWEB)

Huntington, Hillard G. [Executive Director Energy Modeling Forum 450 Terman Center 380 Panama Mall Stanford University Stanford, CA 94305-4026 (United States)

2010-01-15

Long-run adjustments in petroleum consumption are not only larger than short-run adjustments. They may also be motivated by entirely different price events. This analysis shows that new price peaks have both short-run and long-run consumption responses, a result that is starkly different than price changes that track previous price paths. It also establishes significant trend effects where gasoline and residual fuel oil consumption decline over time. The analysis explores these adjustments by establishing long-run cointegrating relationships for different petroleum product groupings. An important implication is that price increases above historical levels may be providing substantially greater incentives for significant long-run demand adjustments than would be the case otherwise. (author)

Petroleum

International Nuclear Information System (INIS)

Anon.

2000-01-01

Here are briefly summarized 1)the OPEC decisions and their consequences concerning the production of petroleum in the world 2)some news about the petroleum industry in Chad and in Iraq 3)some news about the new pipelines constructed or to be constructed in the world 4)some news about the LPG industry (start of a LPG extraction unit in Argentina, legislation in France for LPG vehicles) 4)and some news about the petroleum distribution in France. (O.M.)

Petroleum refining and the national priorities list: The preemption of CERCLA

International Nuclear Information System (INIS)

Hart, D.G.

1991-01-01

The petroleum refining industry has preempted aspects of the implementation of CERCLA through a clause in the original legislation that makes the listing of petroleum refining sites on the NPL more difficult than it would be otherwise. The NPL, which was mandated in CERCLA, is a list of sites open-quotes where a hazardous substance has been deposited, stored, disposed of, placed, or otherwise come to be located. The petroleum exclusion clause, Section 101(14)(F) of CERCLA, states that the term hazardous substance open-quotes does not include petroleum, including crude oil or any fraction thereof which is not otherwise specifically listed or designated as a hazardous substance.close quotes This clause has been interpreted to mean that a site where petroleum products are found may not be listed on the NPL on the basis of the petroleum products; a hazardous substance that is not a normal constituent of petroleum products also must be found at the site. Regression analysis shows that the petroleum refining industry is significantly positively correlated with discovered sites (where a possibility exists that hazardous substances may be present) and significantly negatively correlated with sites that are proposed to the NPL. These, findings suggest that sites that meet the technical criteria for NPL listing are not proposed because of the petroleum exclusion clause. Although the chemical industry also produces substances that are considered hazardous, it is significantly correlated only with proposed sites, and that correlation is positive. The purpose of this paper is to present evidence suggesting that this clause was a response by Congress to an organized interest-the petroleum refining industry, which possessed a political power not available to the less-focused chemical industry

Problems of radiation safety of petroleum and gas production

International Nuclear Information System (INIS)

Garibov, A.A.

2002-01-01

Oil and gas production is the basis of economy of the Azerbaijan Republic and its cause in ecological and radioecology problems. One form this problem is the pollution by radionuclides of environment at the time of gas and petroleum production. At the time of petroleum and gas production the three-phase radionuclides are emitted in atmosphere: Emissions consisted from solid U-238, Ra-226, Th-232, K-40 discharged to atmosphere at the time of production, exploring and exploitation of petroleum and gas. They are presented in compounds of sand, clay, and petroleum residues; During the drilling and production the gross quantities of water flows out and collects. These water areas consist of radium, uranium, Th and K-40 dissolved in water salts; There are the radionuclides being in 902 condition emitted in atmosphere at the places of petroleum and gas production. The radon and its isotopes are emitted at this time; At the places of petroleum and gas production it is observed at local pollution areas polluted by solid emissions that at this territories the doze of exposition power variable 100 - 1000 micro/hour. The radioactivity at this system according to 2-1000 year/k consists from Ra, K-40, and U. At this areas the value of total background changes 5 - 1000 micro R/hour. The total radioactivity of water polls formed at the places of petroleum and gas production consisted 50 -150 Bq/L. In the case of gas the separated radionuclides are mainly consisted from Radon and its isotopes. In the compound of produced gas the concentration of radon varied 20 - 1700 Bq/m 3 . Thus, at the places of petroleum and gas production radioactive pollutants emitted to atmosphere, forms the polluted environment for working and living people at the same territory. This problem's status haven't been investigated thoroughly, the sources of pollution hasn't been uncovered concretely, the cleaning technology for polluted areas is unknown

Effect of petroleum ether and ethanol fractions of seeds of Abrus precatorius on androgenic alopecia

Directory of Open Access Journals (Sweden)

Sukirti Upadhyay

2012-04-01

Full Text Available Seeds of Abrus precatorius L., Fabaceae, are commonly used as purgative, emetic, aphrodisiac and in nervous disorder in traditional and folk medicines. In present study petroleum ether and ethanolic extracts of A. precatorius seeds are evaluated for reversal of androgen (testosterone by i.m route induced alopecia in male albino wistar rats and compared to topical administration of standard antiandrogenic drug finasteride for 21 days. The results were reflected from visual observation and histological study of several skin sections via various parameters as anagen to telogen ratio and follicle density/mm area of skin surface. The animal of group 1 who were treated with only testosterone became alopecic on visual observation. Animals of Group 2, 3 and 4 who were treated with finasteride, petroleum ether and ethanolic extract of seed respectively topically along with testosterone (i.m did not developed alopecia. To investigate the mechanism of observed activity, in vitro experiments were performed. Inhibition of 5α-reductase activity by extracts and finasteride suggest that they reversed androgen induced alopecia by inhibiting conversion of testosterone to dihydrotestosterone (potent androgen responsible for androgenic alopecia. So it may be concluded that petroleum ether and ethanolic extract of A. precatorius seed posses anti androgenic alopecia activity due to inhibition of 5α-reductase enzyme.

Effect of petroleum ether and ethanol fractions of seeds of Abrus precatorius on androgenic alopecia

Directory of Open Access Journals (Sweden)

Sukirti Upadhyay

2011-12-01

Full Text Available Seeds of Abrus precatorius L., Fabaceae, are commonly used as purgative, emetic, aphrodisiac and in nervous disorder in traditional and folk medicines. In present study petroleum ether and ethanolic extracts of A. precatorius seeds are evaluated for reversal of androgen (testosterone by i.m route induced alopecia in male albino wistar rats and compared to topical administration of standard antiandrogenic drug finasteride for 21 days. The results were reflected from visual observation and histological study of several skin sections via various parameters as anagen to telogen ratio and follicle density/mm area of skin surface. The animal of group 1 who were treated with only testosterone became alopecic on visual observation. Animals of Group 2, 3 and 4 who were treated with finasteride, petroleum ether and ethanolic extract of seed respectively topically along with testosterone (i.m did not developed alopecia. To investigate the mechanism of observed activity, in vitro experiments were performed. Inhibition of 5α-reductase activity by extracts and finasteride suggest that they reversed androgen induced alopecia by inhibiting conversion of testosterone to dihydrotestosterone (potent androgen responsible for androgenic alopecia. So it may be concluded that petroleum ether and ethanolic extract of A. precatorius seed posses anti androgenic alopecia activity due to inhibition of 5α-reductase enzyme.

Size-exclusion chromatography for the determination of the boiling point distribution of high-boiling petroleum fractions.

Science.gov (United States)

Boczkaj, Grzegorz; Przyjazny, Andrzej; Kamiński, Marian

2015-03-01

The paper describes a new procedure for the determination of boiling point distribution of high-boiling petroleum fractions using size-exclusion chromatography with refractive index detection. Thus far, the determination of boiling range distribution by chromatography has been accomplished using simulated distillation with gas chromatography with flame ionization detection. This study revealed that in spite of substantial differences in the separation mechanism and the detection mode, the size-exclusion chromatography technique yields similar results for the determination of boiling point distribution compared with simulated distillation and novel empty column gas chromatography. The developed procedure using size-exclusion chromatography has a substantial applicability, especially for the determination of exact final boiling point values for high-boiling mixtures, for which a standard high-temperature simulated distillation would have to be used. In this case, the precision of final boiling point determination is low due to the high final temperatures of the gas chromatograph oven and an insufficient thermal stability of both the gas chromatography stationary phase and the sample. Additionally, the use of high-performance liquid chromatography detectors more sensitive than refractive index detection allows a lower detection limit for high-molar-mass aromatic compounds, and thus increases the sensitivity of final boiling point determination. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Characterization of heavy crude oils and petroleum residues

Energy Technology Data Exchange (ETDEWEB)

Tissot, B.

1984-01-01

Proceedings of an international symposium held in Lyon in 1984, consisting of typescript versions of five plenary lectures and a large number of research papers in the areas of geochemical analysis, fractionation and characterization, and relations between structure and properties.

The variability in iron speciation in size fractionated residual oil fly ash particulate matter (ROFA PM).

Science.gov (United States)

Pattanaik, Sidhartha; Huggins, Frank E; Huffman, Gerald P

2016-08-15

Ambient particulate matter (PM) containing iron can catalyze Fenton reaction leading to the production of reactive oxygen species in cells. It can also catalyze atmospheric redox reaction. These reactions are governed by the physicochemical characteristics of iron in ambient PM. As a surrogate for ambient PM, we prepared residual oil fly ash PM (ROFA PM) in a practical fire tube boiler firing residual oils with varying sulfur and ash contents. The ROFA particles were resolved into fine PM or PM2.5 (aerodynamic diameter (AD)iron speciation in PM2.5+ was ascertained using X-ray absorption spectroscopy and leaching method while that in PM2.5 was reported earlier. The results of both studies are compared to get an insight into the variability in the iron speciation in different size fractions. The results show the predominance of ferric sulfate, with a minor spinal ferrite in both PM (i.e. ZnxNi1-xFe2O4 in PM2.5, ZnFe2O4 in PM2.5+). The iron solubility in ROFA PM depends on its speciation, mode of incorporation of iron into particle's carbonaceous matrix, the grade and composition of oils, and pH of the medium. The soluble fraction of iron in PM is critical in assessing its interaction with the biological systems and its toxic potential. Copyright © 2016 Elsevier B.V. All rights reserved.

Method of removing paraffin from mineral oils, shale oils, tar oils, and their fractions or residues

Energy Technology Data Exchange (ETDEWEB)

Palmquist, F T.E.

1949-09-08

A method is described for removing paraffin from mineral oils, shale oils, tar oils, and their fractions or residues by centrifuging in the presence of oil-dissolving and paraffin-precipitating solvents, by which the precipitated paraffin is made to pass through an indifferent auxiliary liquid, in which a removal of oil takes place, characterized in that as auxiliary liquid is used a liquid or mixture of liquids whose surface tension against the oil solution is sufficiently low for the paraffin to pass the layer of auxiliary liquid in the form of separate crystals.

In situ vadose zone remediation of petroleum-contaminated soils

International Nuclear Information System (INIS)

Greacen, J.R.; Finkel, D.J.

1991-01-01

This paper discusses a pilot-scale system treating vadose zone soils contaminated with petroleum products constructed and operated at a former petroleum bulk storage terminal in New England. A site investigation following decommissioning activities identified more than 100,000 yds of soil at the site contaminated by both No. 2 fuel oil and gasoline. Soil cleanup criteria of 50 ppm TPH and 0.25 ppm BTEX were established. A pilot-scale treatment unit with dimensions of 125 ft x 125 ft x 6 ft was constructed to evaluate the potential for in situ treatment of vadose zone soils. Contaminant levels in pilot cell soils ranged from 0 to 5,250 ppm TPH and 0.0 to 4.2 ppm BTEX. Two soil treatment methods n the pilot system were implemented; venting to treat the lighter petroleum fractions and bioremediation to treat the nonvolatile petroleum constituents. Seven soil gas probes were installed to monitor pressure and soil gas vapor concentrations in the subsurface. Changes in soil gas oxygen and carbon dioxide concentrations were used as an indirect measure of enhanced bioremediation of pilot cell soils. After operating the system for a period of 2.5 months, soil BTEX concentrations were reduced to concentrations below the remediation criteria for the site

Petroleum 2006. Statistical elements

International Nuclear Information System (INIS)

2007-06-01

This document gathers in 5 parts, the main existing statistical data about petroleum industry in France and in the rest of the world, together with an insight on other energy sources: 1 - petroleum in the French economy (petroleum and other energies, petroleum and transports, petroleum and energy in the industry, the residential and tertiary sectors, environment: 42 pages); 2 - the French petroleum industry (exploration, production, foreign trade, transports, refining, storage, petrochemistry: 66 pages); 3 - the French market of petroleum products (evolution of sales by product and detail by region for the past year: 38 pages); 4 - prices and taxes of petroleum products (world prices and rates for crude and refined products, evolution of fret rates, retail prices and French taxes: 28 pages); 5 - petroleum in the world (world energy production and consumption, detailed petroleum activity by main areas and for the main countries: 112 pages). (J.S.)

Petroleum fiscality indicators

International Nuclear Information System (INIS)

2008-02-01

This document presents the different taxes imposed to petroleum products in France: domestic tax on petroleum products (TIPP) and added value tax (TVA). A comparison is made with the fiscality into effect in other European countries for some petroleum products. Then, the fiscality is detailed for the different petroleum products and automotive fuels with its regional modulations. Finally, the fiscal measures adopted in 2007 are detailed. They concern the transposition of the European directive 2003-96/CE into French right and some fiscal regime changes given to some economical sectors particularly penalized by the rise of petroleum energy prices in 2007. (J.S.)

Petroleum industry 1996

International Nuclear Information System (INIS)

1997-01-01

A survey on petroleum industry activities in France and in the world in 1996 is presented. The different parts and themes of the study are: evolution of the petroleum market (international and French markets, supply and demand, prices, mark-up and taxation in France and in Europe); activities in the petroleum industries (exploration and production, maritime transportation, inland transportation and storage, refining, quality of petroleum products and substitution fuels, oil distribution); environment and safety (refining, distribution and evolution of products, pipeline and maritime transportation, exploration and production); situation of the sector's companies (oil groups, para-petroleum French industry, scientific and technical research)

Petroleum industry in 2004

International Nuclear Information System (INIS)

2005-01-01

This document presents a detailed outlook of the petroleum industry in the world and more particularly in France in 2005: evolution of crude oil prices; petroleum exploration and production in the world and in France; the French para-petroleum and petroleum industry; the oil supplies; the refining activities; the evolution of products quality and the substitution fuels; the domestic transports, the storage and consumption of petroleum products; the fiscality, prices and distribution of petroleum products. (J.S.)

Evaluation of soluble fraction and enzymatic residual fraction of dilute dry acid, ethylenediamine, and steam explosion pretreated corn stover on the enzymatic hydrolysis of cellulose.

Science.gov (United States)

Qin, Lei; Liu, Li; Li, Wen-Chao; Zhu, Jia-Qing; Li, Bing-Zhi; Yuan, Ying-Jin

2016-06-01

This study is aimed to examine the inhibition of soluble fraction (SF) and enzymatic residual fraction (ERF) in dry dilute acid (DDA), ethylenediamine (EDA) and steam explosion (SE) pretreated corn stover (CS) on the enzymatic digestibility of cellulose. SF of DDA, EDA and SE pretreated CS has high xylose, soluble lignin and xylo-oligomer content, respectively. SF of EDA pretreated CS leads to the highest inhibition, followed by SE and DDA pretreated CS. Inhibition of ERF of DDA and SE pretreated CS is higher than that of EDA pretreated CS. The inhibition degree (A0/A) of SF is 1.76 and 1.21 times to that of ERF for EDA and SE pretreated CS, respectively. The inhibition degree of ERF is 1.05 times to that of SF in DDA pretreated CS. The quantitative analysis shows that SF of EDA pretreated CS, SF and ERF of SE pretreated CS cause significant inhibition during enzymatic hydrolysis. Copyright © 2016 Elsevier Ltd. All rights reserved.

19 CFR 151.47 - Optional entry of net quantity of petroleum or petroleum products.

Science.gov (United States)

2010-04-01

... 19 Customs Duties 2 2010-04-01 2010-04-01 false Optional entry of net quantity of petroleum or petroleum products. 151.47 Section 151.47 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF... Petroleum and Petroleum Products § 151.47 Optional entry of net quantity of petroleum or petroleum products...

A tiered analytical protocol for the characterization of heavy oil residues at petroleum-contaminated hazardous waste sites

International Nuclear Information System (INIS)

Pollard, S.J.T.; Kenefick, S.L.; Hrudey, S.E.; Fuhr, B.J.; Holloway, L.R.; Rawluk, M.

1994-01-01

The analysis of hydrocarbon-contaminated soils from abandoned refinery sites in Alberta, Canada is used to illustrate a tiered analytical approach to the characterization of complex hydrocarbon wastes. Soil extracts isolated from heavy oil- and creosote-contaminated sites were characterized by thin layer chromatography with flame ionization detection (TLC-FID), ultraviolet fluorescence, simulated distillation (GC-SIMDIS) and chemical ionization GC-MS analysis. The combined screening and detailed analytical methods provided information essential to remedial technology selection including the extent of contamination, the class composition of soil extracts, the distillation profile of component classes and the distribution of individual class components within various waste fractions. Residual contamination was characteristic of heavy, degraded oils, consistent with documented site operations and length of hydrocarbon exposure at the soil surface

The petroleum industry in 2003

International Nuclear Information System (INIS)

2004-01-01

This 2004 edition of the petroleum industry activities presents results and data concerning the crude oil prices evolution, the petroleum exploration and production in france and in the world, the para-petroleum industry, the hydrocarbons supplies, the refining, the quality evolution of the substitution products and fuels, the internal transports of petroleum products, the petroleum products storage, the petroleum products consumption, the petroleum products prices and taxation, the petroleum products distribution. (A.L.B.)

Gasification in petroleum refinery of 21. century; La gazeification dans la raffinerie du petrole du 21. siecle

Energy Technology Data Exchange (ETDEWEB)

Furimsky, E. [IMAF Group, Ottawa, Ontario (Canada)

1999-07-01

The worldwide trends in the crude oil supply indicate a continuous increase of the heavy crudes. The increase in the yield of distillation residues is complemented by an increase in their sulfur content. Additional distillates are produced by upgrading the residues. The upgrading step generates final residues, such as visbreaking tar, coke and asphalt which are produced by visbreaking, coking and de-asphalting, respectively. The final residues can be converted to usable products such as hydrogen, steam, electricity, ammonia and chemicals. For this purpose, gasification has emerged as the technology of choice because of its superior environmental performance when compared with the competing means for residue utilization. Also, refinery sludges can be co-gasified with the final residues and as such, be converted to usable products. If integrated with the petroleum refinery, gasification can diminish any environmental problems associated with residue and sludge disposal. The economic indicators of the refinery can improve as well. The trends in deregulation of the power market enable petroleum refineries to enter this lucrative market either alone or in a partnership with the utilities. The potential of co-production of chemicals and steam with electricity offers the flexibility to respond to market demands. Gasification technology is commercially proven. Among several types, entrained bed gasifiers are the gasifiers of choice. A number of commercial projects in Europe, Asia and United States use a gasifier employing either a slurry feeding system or a dry feeding system. (author)

Mutagenicity and chemical characterization of two petroleum distillates.

Science.gov (United States)

Carver, J H; MacGregor, J A; King, R W

1984-08-01

To investigate if the Salmonella/microsome assay could reliably screen complex petroleum samples for their carcinogenic potential, two high boiling (700-1070 degrees F) petroleum distillates with known activity in a dermal carcinogenesis bioassay were fully characterized with respect to their hydrocarbon composition and polynuclear aromatic hydrocarbon (PNA) content and assayed for mutagenic activity. Mutagenicity assays were also carried out on the aromatic hydrocarbon aggregates separated from these oils by adsorption chromatography. The composition of the distillates differed substantially, and reflected the fact that they were derived from crude oils that were extremely divergent in hydrocarbon character. Both the distillate and aromatic samples consistently induced a very slight increase in revertant TA98 and TA100 colonies; however, an increase of 2-4-fold over background was observed when the S-9 concentration was increased 5-10 times that of the standard assay. The maximal response was less than that expected from the samples' known PNA content and observed potency in the dermal carcinogenesis bioassay. In the Salmonella/microsome assay, all samples inhibited the mutagenic activity of added benzo[a]pyrene. Discordance between the magnitude of the samples' mutagenic activity and their known PNA content may be related to direct or indirect inhibition of sample PNAs by other components of the complex petroleum fractions. Observed inhibitory effects support the use of elevated S-9 concentration in the in vitro assays assessing the carcinogenic potential of petroleum-derived materials.

Crude oil derived petroleum products in the aquatic environment: priorities for control

International Nuclear Information System (INIS)

Grimwood, M.J.

2001-01-01

The available data on the environmental fate, behaviour and toxicity of five groups of petroleum products is reviewed and the information used to identify the priority of oil products for pollution control to protect the aquatic environment. The oil product groups comprise gasolines, kerosenes, other light fuel oil distillates, residual heavy fuel oils and lubricating oils. (author)

Magnetic separation as a plutonium residue enrichment process

International Nuclear Information System (INIS)

Avens, L.R.; Gallegos, U.F.; McFarlan, J.T.

1990-01-01

Several plutonium contaminated residues have been subjected to Open Gradient Magnetic Separation (OGMS) on an experimental scale. OGMS experiments on graphite and bomb reduction residues resulted in a plutonium rich fraction and a plutonium lean fraction. Values for the bulk quantity rejected to the lean fraction varied between about 20% to 85% of the feed bulk. The plutonium content of the lean fraction can be reduced from about 2% in the feed to the 0.1% to 0.5% range dependent on the portion of the feed rejected to this lean fraction. These values are low enough in plutonium to meet economic discard limits and be considered for direct discard. Magnetic separation of pyrochemical salts gave less favorable results. While a fraction very rich in plutonium could be obtained, the lean fraction plutonium content was too high for direct discard. This may still have chemical processing applications. OGMS experiments at low magnetic field strength on incinerator ash did give two fractions but the plutonium content of each fraction was essentially identical. Thus, no chemical processing advantage was identified for magnetic separation of this residue. 6 refs., 1 fig., 9 tabs

Spectrofluorimetric study of the aromatic carbohydrates of Noriisk petroleum

Energy Technology Data Exchange (ETDEWEB)

Alekseeva, T.A.; Lekveishvili, E.G.; Melikadze, L.D.; Teplitskaia, T.A.; Tevdorashvili, M.N.

1979-01-01

Investigation was made of the specimens of aromatic hydrocarbons which were produced by photochemical decomposition of the products of photocondensation with maleicanhydride of narrow aromatic fractions separated by a system of methods from a high temperature part of Noriisk petroleum. Use was made of a standard spectrofluorimeter of low resolution. A series of aromatic hydrocarbons, naphthalene, benzofluorene, phenantrene, chrizene, pyrene, tetraphene, and 3,4-benzophenantrene were installed in the machine.

Clean utilization of high sulphur petroleum coke by circulating fluidized bed combustion (CFBC) in Romania

International Nuclear Information System (INIS)

Dragos, L.; Flueraru, C.; Girjoaba, M.

1996-01-01

The economic and environmental problems caused by inefficient utilization of residual high-sulphur petroleum coke resulted from oil cracking in Romania is discussed. A special research programme applying CFBC technology has been carried out in the Institute for Power Equipment, Bucharest. The results from both laboratory facilities and pilot plant are presented. The main operating conditions and parameters are pointed out. Data on quality and composition of petroleum coke, combustion efficiency, temperature range in different zones and flue gas composition at distinct operating loads are given. The results obtained will be used for innovative design of CFBC boilers based on petroleum coke. A project for implementing a CFBC boiler in one of the Romanian oil refineries is being developed. An analysis of technical and economic advantages of these boilers for energy generation is presented

The petroleum industry in 2005

International Nuclear Information System (INIS)

2006-01-01

This document provides information on the petroleum industry for the year 2005. It discusses the world gas and petroleum markets, the world and french petroleum exploration and production, the petroleum and byproducts industry in France, the hydrocarbons supplying, the refining in France, the evolution of the products and fuels substitution quality, the internal transports of petroleum products, the storage consumption and taxes of petroleum products, the prices and distribution of the petroleum products. (A.L.B.)

Pilot-scale bioremediation of a petroleum hydrocarbon-contaminated clayey soil from a sub-Arctic site.

Science.gov (United States)

Akbari, Ali; Ghoshal, Subhasis

2014-09-15

Bioremediation is a potentially cost-effective solution for petroleum contamination in cold region sites. This study investigates the extent of biodegradation of petroleum hydrocarbons (C16-C34) in a pilot-scale biopile experiment conducted at 15°C for periods up to 385 days, with a clayey soil, from a crude oil-impacted site in northern Canada. Although several studies on bioremediation of petroleum hydrocarbon-contaminated soils from cold region sites have been reported for coarse-textured, sandy soils, there are limited studies of bioremediation of petroleum contamination in fine-textured, clayey soils. Our results indicate that aeration and moisture addition was sufficient for achieving 47% biodegradation and an endpoint of 530 mg/kg for non-volatile (C16-C34) petroleum hydrocarbons. Nutrient amendment with 95 mg-N/kg showed no significant effect on biodegradation compared to a control system without nutrient but similar moisture content. In contrast, in a biopile amended with 1340 mg-N/kg, no statistically significant biodegradation of non-volatile fraction was detected. Terminal Restriction Fragment Length Polymorphism (T-RFLP) analyses of alkB and 16S rRNA genes revealed that inhibition of hydrocarbon biodegradation was associated with a lack of change in microbial community composition. Overall, our data suggests that biopiles are feasible for attaining the bioremediation endpoint in clayey soils. Despite the significantly lower biodegradation rate of 0.009 day(-1) in biopile tank compared to 0.11 day(-1) in slurry bioreactors for C16-C34 hydrocarbons, the biodegradation extents for this fraction were comparable in these two systems. Copyright © 2014 Elsevier B.V. All rights reserved.

Figures on petroleum 1981

Energy Technology Data Exchange (ETDEWEB)

1981-01-01

This table taken out from the 1981 annual report 1981 contains an introductory remark on the reorganization of mineral oil statistics up to January 82. It is followed by the tables ranged as follows: refinery capacity and production, crude oil supply, GDR-coverings, import of petroleum products, petroleum consumption, export of petroleum products, transport, oil storage tanks, motor vehicle stock, taxes and tariffs, petroleum export trade, energy consumption and world petroleum numbers. In parts the tables contain comparative figures back to 1950.

Characterization of commercial ceramic adsorbents and their application on naphthenic acids removal of petroleum distillates; Caracterizacao de adsorventes ceramicos comerciais e sua aplicacao na remocao de acidos naftenicos de destilados de petroleo

Energy Technology Data Exchange (ETDEWEB)

Silva, J.P.; Senna, L.F. de; Lago, D.C.B. do; Silva Junior, P.F. da; Figueiredo, M.A.G. de; Dias, E.G. [Universidade do Estado do Rio de Janeiro (UERJ), RJ (Brazil)], e-mail: julia_psi@yahoo.com.br; Chiaro, S.S.X. [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil). Centro de Pesquisas (CENPES)

2006-07-01

One denominates 'naphthenic acids' to the mixture of carboxylic acids that is present in petroleum oil, and is directly responsible for its acidity and corrosiveness in liquid phase during the refine process. These acids are also presents in distilled fraction of petroleum, causing several problems in final products quality. A possible way to remove them from petroleum distilled fractions is the adsorption in porous materials. However, the published results indicate that ion exchange resins would be the best adsorbents for this process, which would probably increase its cost. In this work, two commercial adsorbents (clay and activated alumina) were characterized by a set of physical-chemistry techniques and evaluated concerning their capacity of removing naphthenic acids from a light petroleum fraction. It was also verified the influence of a previous thermal treatment to the adsorption in their physical-chemistry characteristics and its properties. (author)

Development of a field testing protocol for identifying Deepwater Horizon oil spill residues trapped near Gulf of Mexico beaches

Science.gov (United States)

Han, Yuling

2018-01-01

The Deepwater Horizon (DWH) accident, one of the largest oil spills in U.S. history, contaminated several beaches located along the Gulf of Mexico (GOM) shoreline. The residues from the spill still continue to be deposited on some of these beaches. Methods to track and monitor the fate of these residues require approaches that can differentiate the DWH residues from other types of petroleum residues. This is because, historically, the crude oil released from sources such as natural seeps and anthropogenic discharges have also deposited other types of petroleum residues on GOM beaches. Therefore, identifying the origin of these residues is critical for developing effective management strategies for monitoring the long-term environmental impacts of the DWH oil spill. Advanced fingerprinting methods that are currently used for identifying the source of oil spill residues require detailed laboratory studies, which can be cost-prohibitive. Also, most agencies typically use untrained workers or volunteers to conduct shoreline monitoring surveys and these worker will not have access to advanced laboratory facilities. Furthermore, it is impractical to routinely fingerprint large volumes of samples that are collected after a major oil spill event, such as the DWH spill. In this study, we propose a simple field testing protocol that can identify DWH oil spill residues based on their unique physical characteristics. The robustness of the method is demonstrated by testing a variety of oil spill samples, and the results are verified by characterizing the samples using advanced chemical fingerprinting methods. The verification data show that the method yields results that are consistent with the results derived from advanced fingerprinting methods. The proposed protocol is a reliable, cost-effective, practical field approach for differentiating DWH residues from other types of petroleum residues. PMID:29329313

Development of a field testing protocol for identifying Deepwater Horizon oil spill residues trapped near Gulf of Mexico beaches.

Science.gov (United States)

Han, Yuling; Clement, T Prabhakar

2018-01-01

The Deepwater Horizon (DWH) accident, one of the largest oil spills in U.S. history, contaminated several beaches located along the Gulf of Mexico (GOM) shoreline. The residues from the spill still continue to be deposited on some of these beaches. Methods to track and monitor the fate of these residues require approaches that can differentiate the DWH residues from other types of petroleum residues. This is because, historically, the crude oil released from sources such as natural seeps and anthropogenic discharges have also deposited other types of petroleum residues on GOM beaches. Therefore, identifying the origin of these residues is critical for developing effective management strategies for monitoring the long-term environmental impacts of the DWH oil spill. Advanced fingerprinting methods that are currently used for identifying the source of oil spill residues require detailed laboratory studies, which can be cost-prohibitive. Also, most agencies typically use untrained workers or volunteers to conduct shoreline monitoring surveys and these worker will not have access to advanced laboratory facilities. Furthermore, it is impractical to routinely fingerprint large volumes of samples that are collected after a major oil spill event, such as the DWH spill. In this study, we propose a simple field testing protocol that can identify DWH oil spill residues based on their unique physical characteristics. The robustness of the method is demonstrated by testing a variety of oil spill samples, and the results are verified by characterizing the samples using advanced chemical fingerprinting methods. The verification data show that the method yields results that are consistent with the results derived from advanced fingerprinting methods. The proposed protocol is a reliable, cost-effective, practical field approach for differentiating DWH residues from other types of petroleum residues.

Determination of average molecular parameters of vacuum residues and asphalt by elementary analysis and 1 H NMR and comparison with 13 C NMR results

International Nuclear Information System (INIS)

Teixeira, Marco Antonio; Marques, Rosana Garrido

1995-01-01

This work proposes a new approach for determining average molecular parameters in petroleum fractions, from some approximation based on consideration about average composition of petroleum heavy fractions. A comparative evaluation between the proposed method and the traditional one has been carried out, showing 60 hours saving in time spent at analysis. The results were present and discussed

Lab-scale pyrolysis of the Automotive Shredder Residue light fraction and characterization of tar and solid products.

Science.gov (United States)

Anzano, Manuela; Collina, Elena; Piccinelli, Elsa; Lasagni, Marina

2017-06-01

The general aim of this study is the recovery of Automotive Shredder Residue (ASR). The ASR light fraction, or car fluff, that was collected at an Italian shredding plant was pyrolysed at various temperatures (500-800°C) in a lab-scale reactor. The condensable gases (tar) and solid residue yields increased with decreasing temperature, and these products were characterized to suggest a potential use to reclaim them. The higher heating value (HHV) of tar was 34-37MJ/kg, which is comparable with those of fossil fuels. Furthermore, the ash content was low (0.06-4.98%). Thus, tar can be used as an alternative fuel. With this prospect, the concentrations of polychlorinated dibenzodioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) in tar were determined. The toxicity of tar changes with temperature (1-5ng I-TEQ/g), and the PCDFs significantly contribute to tar toxicity, which was 75-100% with a maximum of 99.6% at 700°C. Regarding the characterization of the solid residue, the low HHV (2.4-3.3MJ/kg) does not make it suitable for energy recovery. Regarding material recovery, we considered its use as a filler in construction materials or a secondary source for metals. It shows a high metal concentration (280,000-395,000mg/kg), which is similar at different pyrolysis temperatures. At 500°C, polycyclic aromatic hydrocarbons (PAHs) were not detected in the solid residue, whereas the maximum total PAH concentration (19.41ng/g, 700°C) was lower than that in fly ash from MSWI. In conclusion, 500°C is a suitable pyrolysis temperature to obtain valuable tar and solid residue. Copyright © 2017 Elsevier Ltd. All rights reserved.

Hydrodesulfurization and hydrodemetallization of different origin vacuum residues : new modeling approach.

OpenAIRE

Ferreira , Cristina; Tayakout-Fayolle , Melaz; Guibard , Isabelle; Lemos , Francisco

2014-01-01

International audience; In order to be able to upgrade the heaviest part of the crude oil one needs to remove several impurities, such as sulfur or metals. Residue hydrotreatment in fixed beds, under high hydrogen pressure can achieve high removal performances, with an industrial catalysts optimized staging. Despite the recent improvements, petroleum residues remain very difficult to describe and characterize in detail. Several kinetic models have been developed, but mostly they are feed depe...

Preparation of fuels and chemical products from mixtures of coal and petroleum

Energy Technology Data Exchange (ETDEWEB)

Krichko, A A; Yulin, M K

1973-01-01

The distillate to 320/sup 0/C from the liquid phase hydrogenation of a 1 : 1 coal-Arlan petroleum mixture was processed to yield phenols 3.4 percent, high aromatics gasoline 81.2 percent, C/sub 1/--C/sub 4/ alkanes 13.5 percent, H/sub 2/S 0.5 percent, and water 1.0 percent. Thus, C/sub 6/--C/sub 8/ phenols were separated from the fraction distilling to 240/sup 0/C, and the phenol-free fraction and the 240 to 320/sup 0/C fraction were hydrofined over an aluminum-cobalt-molybdenum catalyst at 400/sup 0/C and 50 atm. Distillation gave a gasoline fraction, which was reformed, and a 180 to 320/sup 0/C fraction, which was hydrocracked at 380/sup 0/C and 40 atm on a zeolite catalyst.

Petroleum price

International Nuclear Information System (INIS)

Chevallier, B.

2009-01-01

The 'AFTP' conference on 'petroleum prices' organized by Total last March, tries to explain the different aspects of the crisis we undergo for July 2007 and its consequential effects on the petroleum markets (supply, demand evolvements, impacts on reserves, prices, refining...). (O.M.)

Hydrocracking of atmospheric distillable residue of Mongolian oil

Directory of Open Access Journals (Sweden)

Ts Tugsuu

2014-09-01

Full Text Available Many catalytic processes to refine heavy part of crude oil have attracted much interest due to declining reserves of light crude oils. This study focused on hydrocracking process of atmospheric distillable residue of Mongolian crude oil in the first time compared to those of other countries. Residue samples were hydrocracked with a commercial catalyst at 450°C, 460°C, 470°C for 2 h under hydrogen pressure of 10 MPa. The amount of residual fraction (350°Cresidue from Tamsagbulag crude oil. When the ME-AR was hydrocracked, the high consumption of hydrogen was related to the lowest H/C atomic ratio of feed atmospheric residue. The amount of liquid fractions (BP<350°C including gaseous products increased from 45.4wt% to 89.2wt%, when the reaction temperature increased from 450°C to 470°C. The highest yield of the middle fraction for each sample was observed at temperature of 460°C. On the other hand, the effect of temperature on the yield of middle fraction was not so high as compared with the yields of other fractions. The contents of n-paraffins on midlle and heavy fractions of TB-AR, DQ-AR were similar, but ME-AR’s was around 2 times lower than other after hydrocracking runs.DOI: http://dx.doi.org/10.5564/mjc.v12i0.166 Mongolian Journal of Chemistry Vol.12 2011: 24-28 

77 FR 56421 - Standards of Performance for Petroleum Refineries; Standards of Performance for Petroleum...

Science.gov (United States)

2012-09-12

... Parts 9 and 60 Standards of Performance for Petroleum Refineries; Standards of Performance for Petroleum...-9672-3] RIN 2060-AN72 Standards of Performance for Petroleum Refineries; Standards of Performance for Petroleum Refineries for Which Construction, Reconstruction, or Modification Commenced After May 14, 2007...

International comparison CCQM-K119 liquefied petroleum gas

Science.gov (United States)

Brewer, P. J.; Downey, M. L.; Atkins, E.; Brown, R. J. C.; Brown, A. S.; Zalewska, E. T.; van der Veen, A. M. H.; Smeulders, D. E.; McCallum, J. B.; Satumba, R. T.; Kim, Y. D.; Kang, N.; Bae, H. K.; Woo, J. C.; Konopelko, L. A.; Popova, T. A.; Meshkov, A. V.; Efremova, O. V.; Kustikov, Y.

2018-01-01

Liquefied hydrocarbon mixtures with traceable composition are required in order to underpin measurements of the composition and other physical properties of LPG (liquefied petroleum gas), thus meeting the needs of an increasingly large industrial market. This comparison aims to assess the analytical capabilities of laboratories for measuring the composition of a Liquid Petroleum Gas (LPG) mixture when sampled in the liquid phase from a Constant Pressure Cylinder. Mixtures contained ethane, propane, propene, i-butane, n-butane, but-1-ene and i-pentane with nominal amount fractions of 2, 71, 9, 4, 10, 3 and 1 cmol mol-1 respectively. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Surfactants from petroleum paraffin wax

Energy Technology Data Exchange (ETDEWEB)

Kassem, T.M.; Hussein, M.H.; El Sayed, A.S.

Paraffin wax from Egyptian petroleum was purified and then oxidized to fatty acids which were esterified to form their methyl esters, fractionated and then hydrolysed. The obtained fatty acids were converted into the corresponding primary amines which were converted with ethylene oxide to form nonionic surfactants. The prepared primary amines were also converted into tertiary amines and then converted into cationic surfactants through condensation with benzyl chloride or 1-chloromethylnaphthalene. Also, amine oxide surfactants were prepared by oxidation of the tertiary amines with hydrogen peroxide. The surface active properties of all the prepared surfactants were determined, and the effect of their chemical structure on the surfactant properties are discussed in this paper.

Photolysis of petroleum

International Nuclear Information System (INIS)

Bobra, M.

1992-05-01

A study was conducted to examine the chemical and physical changes that occur in oils as a result of photooxidation. A literature review of recent studies in petroleum photochemistry revealed reported effects of photo-induced reactions in petroleum, including changes in color, polymerization, solidification, increases in solubility and toxicity, and changes in interfacial properties. A list of products reported as a result of photolysis of petroleum is presented, including such compounds as aldehydes, ketones, esters, and lactones. The photoreactivity of various petroleum components is discussed and mechanisms of photooxidation of petroleum are suggested. In the experimental portion of the study, a variety of crude oils and petroleum products were used to determine how different oils are affected by photolysis, and to examine the importance of photolysis as a weathering process. Photooxidation products from several oils were isolated and identified, including aliphatic and aromatic acids, alcohols, and phenols. Some physical manifestations attributed to photolysis included yellowing, formation of precipitates or crusts, increases in density and viscosity with time, increases of asphaltene content in some oils, changes in pH of the surrounding water, and emulsification. 51 refs., 38 figs., 18 tabs

Fractionation of Uranium Forms as Affected by Spiked Soil Treatment and Soil Type

International Nuclear Information System (INIS)

Lotfy, S.M.; Mostafa, A.Z.; Abdel-Sabour, M.F.

2012-01-01

In a fractionation experiment Uranium forms were compared in two soil types (Mostorud and Elgabalelasfar soil). Also, the variation of U forms due to soil treatment (spiking) were studied. In case of Mostorud soil the initial U - fractions were 45.63 % as residual form, 20.69 % organically bound 16.36 % Mn and Fe oxides bound, 9.76% Carbonate form, 7.41 % exchangeable fractions and 0.15% water soluble fractions. These fractions varied significantly when the soil was spiked with 200 mg U/Kg soil to 46.88 %, 23.19 %, 9.97 %, 16.07 %, 3.79% and 0.10% for residual, organically, Mn- Fe oxide, carbonate, exchangeable and water soluble fractions respectively. These result showed significant reduction in U-ex fraction forms and Mn- Fe bound forms with significant increase in U- carbonate form due to U application. In case of Elgabalelasfar soil, the main U - fractions were 57.42% as residual form (relatively higher residual - U form in the clayey soil) 16.10 % organically bound, 13.78% Mn and Fe oxides bound, 7.22 % Carbonate form, 5.23 % exchangeable fractions and 0.25 % water soluble fractions The application of 200 mg U/Kg soil resulted in a significant changes in U - Fractions distribution as follows : 59.26 % , 11.27 % , 19.59 % , 6.84 % , 2.90 % and 0.14 % for residual , organic , Mn- Fe oxides , carbonate, exchangeable and water soluble fractions , respectively.

Partnership in an application of RBCA: Case study for quantitative assessment of total petroleum hydrocarbons

International Nuclear Information System (INIS)

Srinivasan, K.; Shepherd, D.

1995-01-01

Risk-Based Corrective Action (RBCA) was successfully applied at a site contaminated with weathered Total Petroleum Hydrocarbons (TPH) from a past release of Diesel Fuel No. 2. In partnership with the state regulatory agency, an approach was developed to assess the toxicity of TPH by the evaluation of its individual classes/constituents. Historically, assessments of petroleum product releases have focused solely on TPH as an analytical parameter and not its individual fractions and/or constituents which represent the actual toxicity of the released product. Soil and groundwater TPH data by Modified California Method 8015 (GC/MS) were reviewed. Based on analytical standards, typical Diesel Fuel No. 2 carbon ranges/fractions were identified. In addition, site-specific carbon-chain lengths were identified based on the aforementioned standard. In consultation with state regulators and according to state draft RBCA guidance, site-specific polycyclic aromatic hydrocarbons (PAHs) and three TPH carbon-range fractions were identified as constituents of concern. In order to quantify the three TPH fractions, appropriate toxicological surrogates were identified. Site-specific exposures to potential human and ecological receptors were evaluated in close consultation with the state regulators. Limited contaminant fate and transport analysis was conducted. Subsequently, complete exposure pathways were quantified

46 CFR 148.04-15 - Petroleum coke, uncalcined; petroleum coke, uncalcined and calcined (mixture).

Science.gov (United States)

2010-10-01

... 46 Shipping 5 2010-10-01 2010-10-01 false Petroleum coke, uncalcined; petroleum coke, uncalcined and calcined (mixture). 148.04-15 Section 148.04-15 Shipping COAST GUARD, DEPARTMENT OF HOMELAND... Requirements for Certain Material § 148.04-15 Petroleum coke, uncalcined; petroleum coke, uncalcined and...

Petroleum and geopolitics

International Nuclear Information System (INIS)

Chaigneau, P.

2004-01-01

Todays, petroleum companies consider that despite the constant increase of petroleum consumption, petroleum will remain the main energy source for at least 40 years. However, after the Iraq conflict, new regional situations are changing. China, for instance, with its growing up demand, will change the physiognomy of the oil market. In parallel, from Indonesia to Africa, petroleum and religion interfere and explain the new conflict areas. As for the US strategy, which is not limited to the energy paradigm, it largely integrates energy in the main lines of its diplomacy, from the 'Wide Middle East' to the 'Sahel initiative', and in its position with respect to Venezuela

Analgesic and Antipyretic Activities of Methanol Extract and Its Fraction from the Root of Schoenoplectus grossus

Directory of Open Access Journals (Sweden)

Nirmal Kumar Subedi

2016-01-01

Full Text Available The study aims to evaluate analgesic and antipyretic activities of the methanol extract and its different fractions from root of Schoenoplectus grossus using acetic acid induced writhing and radiant heat tail flick method of pain models in mice and yeast induced pyrexia in rats at the doses of 400 and 200 mg/kg. In acetic acid writhing test, the methanol extract, petroleum ether, and carbon tetrachloride fractions produced significant (P<0.001 and P<0.05 inhibition of writhing responses in dose dependent manner. The methanol extract at 400 and 200 mg/kg being more protective with 54% and 45.45% of inhibition compared to diclofenac sodium of 56% followed by petroleum ether fractions of 49.69% and 39.39% at the same doses. The extracts did not produce any significant antinociceptive activity in tail flick test except standard morphine. When studied on yeast induced pyrexia, methanol and petroleum ether fractions significantly lowered the rectal temperature time dependently in a manner similar to standard drug paracetamol and distinctly more significant (P<0.001 after second hour. These findings suggest that the root extracts of S. grossus possess significant peripherally acting analgesic potential and antipyretic property. The phytochemical screening showed the presence of flavonoids, alkaloids, and tannins.

Methyl bromide residues in fumigated cocoa beans

International Nuclear Information System (INIS)

Adomako, D.

1975-01-01

The 14 C activity in unroasted [ 14 C]-methyl bromide fumigated cocoa beans was used to study the fate and persistence of CH 3 Br in the stored beans. About 70% of the residues occurred in the shells. Unchanged CH 3 Br could not be detected, all the sorbed CH 3 Br having reacted with bean constituents apparently to form 14 C-methylated derivatives and inorganic bromide. No 14 C activity was found in the lipid fraction. Roasting decreased the bound (non-volatile) residues, with corresponding changes in the activities and amounts of free sugars, free and protein amino acids. Roasted nibs and shells showed a two-fold increase in the volatile fraction of the 14 C residue. This fraction may be related to the volatile aroma compounds formed by Maillard-type reactions. (author)

Fundamentals of a moderate thermocracking-deep deasphalting combined process of Karamay vacuum residue

Energy Technology Data Exchange (ETDEWEB)

Zhiming, X; Tonghua, L.; Suogi, Z.; Renan, W. [University of Petroleum, State Key Laboratory of Heavy Oil Processing, Beijing (China); Lailong, L.; Zhen, L. [Karamay Petrochemical Company, Petrochemical Research Institute, Karamay (China)

2004-07-01

Thermocracking of heavy oil vacuum residue was carried out to determine the optimum conditions for the thermal cracking of Karamay vacuum residue prior to coke formation. The vacuum residue and the cracked residue after distillation were separated using supercritical fluid extraction and fractionation techniques. Sixteen and thirteen fractions and non-extractable end cuts respectively were separated, and their properties, compositions and average structures determined. Solubility parameters of the end cuts were measured, and those of the fractions calculated. The solubility parameter of the end cut of distilled residue was found to have greatly increased. It was determined that when the difference of the end cut and the extractable fractions amounts to 6.37MPa1/2, in the case of Karamay vacuum residue coke will deposit under thermocracking conditions. Based on the results of a series of solvent deep deasphalting experiments, a scheme for vacuum residue thermocracking and deasphalting of the cracked residue was proposed.

Pilot-scale bioremediation of a petroleum hydrocarbon-contaminated clayey soil from a sub-Arctic site

International Nuclear Information System (INIS)

Akbari, Ali; Ghoshal, Subhasis

2014-01-01

Highlights: • Aeration and moisture addition alone caused extensive hydrocarbon biodegradation. • 30-day slurry reactor remediation endpoints attained in 385 days in biopiles. • High nitrogen concentrations inhibited hydrocarbon degradation. • Inhibition of biodegradation linked to lack of shifts in soil microbial community. - Abstract: Bioremediation is a potentially cost-effective solution for petroleum contamination in cold region sites. This study investigates the extent of biodegradation of petroleum hydrocarbons (C16–C34) in a pilot-scale biopile experiment conducted at 15 °C for periods up to 385 days, with a clayey soil, from a crude oil-impacted site in northern Canada. Although several studies on bioremediation of petroleum hydrocarbon-contaminated soils from cold region sites have been reported for coarse-textured, sandy soils, there are limited studies of bioremediation of petroleum contamination in fine-textured, clayey soils. Our results indicate that aeration and moisture addition was sufficient for achieving 47% biodegradation and an endpoint of 530 mg/kg for non-volatile (C16–C34) petroleum hydrocarbons. Nutrient amendment with 95 mg-N/kg showed no significant effect on biodegradation compared to a control system without nutrient but similar moisture content. In contrast, in a biopile amended with 1340 mg-N/kg, no statistically significant biodegradation of non-volatile fraction was detected. Terminal Restriction Fragment Length Polymorphism (T-RFLP) analyses of alkB and 16S rRNA genes revealed that inhibition of hydrocarbon biodegradation was associated with a lack of change in microbial community composition. Overall, our data suggests that biopiles are feasible for attaining the bioremediation endpoint in clayey soils. Despite the significantly lower biodegradation rate of 0.009 day −1 in biopile tank compared to 0.11 day −1 in slurry bioreactors for C16–C34 hydrocarbons, the biodegradation extents for this fraction were

Evaluation of kinetic uncertainty in numerical models of petroleum generation

Science.gov (United States)

Peters, K.E.; Walters, C.C.; Mankiewicz, P.J.

2006-01-01

Oil-prone marine petroleum source rocks contain type I or type II kerogen having Rock-Eval pyrolysis hydrogen indices greater than 600 or 300-600 mg hydrocarbon/g total organic carbon (HI, mg HC/g TOC), respectively. Samples from 29 marine source rocks worldwide that contain mainly type II kerogen (HI = 230-786 mg HC/g TOC) were subjected to open-system programmed pyrolysis to determine the activation energy distributions for petroleum generation. Assuming a burial heating rate of 1??C/m.y. for each measured activation energy distribution, the calculated average temperature for 50% fractional conversion of the kerogen in the samples to petroleum is approximately 136 ?? 7??C, but the range spans about 30??C (???121-151??C). Fifty-two outcrop samples of thermally immature Jurassic Oxford Clay Formation were collected from five locations in the United Kingdom to determine the variations of kinetic response for one source rock unit. The samples contain mainly type I or type II kerogens (HI = 230-774 mg HC/g TOC). At a heating rate of 1??C/m.y., the calculated temperatures for 50% fractional conversion of the Oxford Clay kerogens to petroleum differ by as much as 23??C (127-150??C). The data indicate that kerogen type, as defined by hydrogen index, is not systematically linked to kinetic response, and that default kinetics for the thermal decomposition of type I or type II kerogen can introduce unacceptable errors into numerical simulations. Furthermore, custom kinetics based on one or a few samples may be inadequate to account for variations in organofacies within a source rock. We propose three methods to evaluate the uncertainty contributed by kerogen kinetics to numerical simulations: (1) use the average kinetic distribution for multiple samples of source rock and the standard deviation for each activation energy in that distribution; (2) use source rock kinetics determined at several locations to describe different parts of the study area; and (3) use a weighted

Application of petroleum markers to geochemical and environmental investigations

International Nuclear Information System (INIS)

Abu-Elgheit, M.A.; El-Gayar, M.S.; Hegazi, A.H.

1998-01-01

Application of trace-metal and biological markers to geochemical studies has shown that crude oils could be correlated or differentiated according to their geologic age. The V/Ni, V/Σ Ni, Mg, Fe, and pristine to phytane (Pr/Ph) markers were almost uniform in Gulf of Suez crude oils, revealing their same origin, yet showing marked differences in Western Desert crude oils, reflecting varying degrees of their maturity and migrational history. The significance of petroleum markers was extended to monitoring of oil spill sources. Weathering of spills usually renders their source identification questionable by infrared or gas chromatography profiles. Since evaporative loss light petroleum fractions does not appreciably affect the high-Molecular Weight components with which trace metals, isoprenoids, hopanes, and steranes are associated, V/Ni, Pr/Ph, m/z 191, and m/z 217 mass chromatogram fragments were found reliable in fingerprinting oil spill sources in Mediterranean waters

Petroleum system of Northwest Java basin based on gravity data analysis

Science.gov (United States)

Widianto, E.

2018-01-01

Energy management in the upstream oil and gas sector becomes very important for the country’s energy security. The renewal of energy resources and reserves becomes necessary and is a must. In the oil and gas industry, gravity data is usually used only for regional surveys, but with the development of instrumentation technology and gravity software development, this method can be used for assessing oil and gas survey stages from exploration to production. This study was conducted to evaluate aspects of petroleum system and exploration play concept in the part of Northwest Java Basin, covering source rock deposition regions (source kitchen area, migration direction), development of reservoirs, structural and stratigraphic trap, based on gravity data. This study uses data from Bouguer gravity anomaly map by filtering process to produce a residual map depicting sedimentation basin configuration. The mapping generated 20 sedimentary basins in Java Island with the total hydrocarbon resources of 113 BBOE (Billion Barrel of Oil Equivalent). The petroleum system analysis was conducted in the Northwest Basin section. The final map produced illustrates the condition of petroleum system and play concept that can be used as exploration direction, expectedly reducing the risk of drilling failure.

Life cycle assessment of residual lignocellulosic biomass-based jet fuel with activated carbon and lignosulfonate as co-products.

Science.gov (United States)

Pierobon, Francesca; Eastin, Ivan L; Ganguly, Indroneil

2018-01-01

Bio-jet fuels are emerging as a valuable alternative to petroleum-based fuels for their potential for reducing greenhouse gas emissions and fossil fuel dependence. In this study, residual woody biomass from slash piles in the U.S. Pacific Northwest is used as a feedstock to produce iso-paraffinic kerosene, through the production of sugar and subsequent patented proprietary fermentation and upgrading. To enhance the economic viability and reduce the environmental impacts of iso-paraffinic kerosene, two co-products, activated carbon and lignosulfonate, are simultaneously produced within the same bio-refinery. A cradle-to-grave life cycle assessment (LCA) is performed for the residual woody biomass-based bio-jet fuel and compared against the cradle-to-grave LCA of petroleum-based jet fuel. This paper also discusses the differences in the environmental impacts of the residual biomass-based bio-jet fuel using two different approaches, mass allocation and system expansion, to partition the impacts between the bio-fuel and the co-products, which are produced in the bio-refinery. The environmental assessment of biomass-based bio-jet fuel reveals an improvement along most critical environmental criteria, as compared to its petroleum-based counterpart. However, the results present significant differences in the environmental impact of biomass-based bio-jet fuel, based on the partitioning method adopted. The mass allocation approach shows a greater improvement along most of the environmental criteria, as compared to the system expansion approach. However, independent of the partitioning approach, the results of this study reveal that more than the EISA mandated 60% reduction in the global warming potential could be achieved by substituting petroleum-based jet fuel with residual woody biomass-based jet fuel. Converting residual woody biomass from slash piles into bio-jet fuel presents the additional benefit of avoiding the impacts of slash pile burning in the forest, which

Dry matter and root colonization of plants by indigenous arbuscular mycorrhizal fungi with physical fractions of dry olive mill residue inoculated with saprophytic fungi

Energy Technology Data Exchange (ETDEWEB)

Aranda, E.; Sampredro, I.; Diaz, R.; Garcia-Sanchez, M.; Siles, J. A.; Ocampo, J. A.; Garcia-Romera, I.

2010-07-01

We studied the influence of indigenous arbuscular mycorrhizal (AM) and saprobe fungi on the phytotoxicity of the physical fractions of dry olive mill residue (DOR). The physical extractions of DOR gave an aqueous (ADOR) and an exhausted (SDOR) fraction with less phytotoxicity for tomato than the original samples. The indigenous AM were able to decrease the phytotoxicity of SDOR inoculated with Trametes versicolor and Pycnoporus cinnabarinus on tomato. However, incubation of ADOR with both saprophytic fungi did not decrease its phytotoxicity in presence of the indigenous AM fungi. The percentage of root length colonized by indigenous AM strongly decreased in presence of DOR, around 80% of decrease at dose of 25 g kg-1of DOR, but the level of mycorrhization was higher in presence of ADOR or SDOR (38% and 44% of decrease respectively at the same dose). There were no relationships between the effects of the physical fractions of DOR incubated with the saprobe fungi on AM colonization and on plant dry weight of tomato. Our results suggest that the phytotoxicity of the olive residues can be eliminated by the combination of physical extraction and by saprobe fungal inoculation and the use of this agrowaste as organic amendment in agricultural soil may be possible. (Author) 33 refs.

Petroleum and Health Care: Evaluating and Managing Health Care's Vulnerability to Petroleum Supply Shifts

Science.gov (United States)

Bednarz, Daniel; Bae, Jaeyong; Pierce, Jessica

2011-01-01

Petroleum is used widely in health care—primarily as a transport fuel and feedstock for pharmaceuticals, plastics, and medical supplies—and few substitutes for it are available. This dependence theoretically makes health care vulnerable to petroleum supply shifts, but this vulnerability has not been empirically assessed. We quantify key aspects of petroleum use in health care and explore historical associations between petroleum supply shocks and health care prices. These analyses confirm that petroleum products are intrinsic to modern health care and that petroleum supply shifts can affect health care prices. In anticipation of future supply contractions lasting longer than previous shifts and potentially disrupting health care delivery, we propose an adaptive management approach and outline its application to the example of emergency medical services. PMID:21778473

Application of enhanced gas chromatography/triple quadrupole mass spectrometry for monitoring petroleum weathering and forensic source fingerprinting in samples impacted by the Deepwater Horizon oil spill.

Science.gov (United States)

Adhikari, Puspa L; Wong, Roberto L; Overton, Edward B

2017-10-01

Accurate characterization of petroleum hydrocarbons in complex and weathered oil residues is analytically challenging. This is primarily due to chemical compositional complexity of both the oil residues and environmental matrices, and the lack of instrumental selectivity due to co-elution of interferences with the target analytes. To overcome these analytical selectivity issues, we used an enhanced resolution gas chromatography coupled with triple quadrupole mass spectrometry in Multiple Reaction Monitoring (MRM) mode (GC/MS/MS-MRM) to eliminate interferences within the ion chromatograms of target analytes found in environmental samples. This new GC/MS/MS-MRM method was developed and used for forensic fingerprinting of deep-water and marsh sediment samples containing oily residues from the Deepwater Horizon oil spill. The results showed that the GC/MS/MS-MRM method increases selectivity, eliminates interferences, and provides more accurate quantitation and characterization of trace levels of alkyl-PAHs and biomarker compounds, from weathered oil residues in complex sample matrices. The higher selectivity of the new method, even at low detection limits, provides greater insights on isomer and homolog compositional patterns and the extent of oil weathering under various environmental conditions. The method also provides flat chromatographic baselines for accurate and unambiguous calculation of petroleum forensic biomarker compound ratios. Thus, this GC/MS/MS-MRM method can be a reliable analytical strategy for more accurate and selective trace level analyses in petroleum forensic studies, and for tacking continuous weathering of oil residues. Copyright © 2017 Elsevier Ltd. All rights reserved.

Petroleum and ethics

International Nuclear Information System (INIS)

Henn, N.; Train, E.; Chagnoux, H.; Heinzle, P.; Daubresse, M.; Bret-Rouzaut, N.; Fradin, J.

2000-01-01

7 articles in this data sheet, they concern: political stakes and stakes of the industrial petroleum sector towards ethical questions; establishment of associations attending to human and environmental questions; examples of of ethical, environmental and safety policy in an industrialized country (ExxonMobil) and in a developing country (TotalFina); synthesis of the ethical problems that the petroleum industry encounter in industrialized and developing countries; considerations on the communication stakes in petroleum companies with the general public. (O.M.)

North Slope, Alaska: Source rock distribution, richness, thermal maturity, and petroleum charge

Science.gov (United States)

Peters, K.E.; Magoon, L.B.; Bird, K.J.; Valin, Z.C.; Keller, M.A.

2006-01-01

Four key marine petroleum source rock units were identified, characterized, and mapped in the subsurface to better understand the origin and distribution of petroleum on the North Slope of Alaska. These marine source rocks, from oldest to youngest, include four intervals: (1) Middle-Upper Triassic Shublik Formation, (2) basal condensed section in the Jurassic-Lower Cretaceous Kingak Shale, (3) Cretaceous pebble shale unit, and (4) Cretaceous Hue Shale. Well logs for more than 60 wells and total organic carbon (TOC) and Rock-Eval pyrolysis analyses for 1183 samples in 125 well penetrations of the source rocks were used to map the present-day thickness of each source rock and the quantity (TOC), quality (hydrogen index), and thermal maturity (Tmax) of the organic matter. Based on assumptions related to carbon mass balance and regional distributions of TOC, the present-day source rock quantity and quality maps were used to determine the extent of fractional conversion of the kerogen to petroleum and to map the original TOC (TOCo) and the original hydrogen index (HIo) prior to thermal maturation. The quantity and quality of oil-prone organic matter in Shublik Formation source rock generally exceeded that of the other units prior to thermal maturation (commonly TOCo > 4 wt.% and HIo > 600 mg hydrocarbon/g TOC), although all are likely sources for at least some petroleum on the North Slope. We used Rock-Eval and hydrous pyrolysis methods to calculate expulsion factors and petroleum charge for each of the four source rocks in the study area. Without attempting to identify the correct methods, we conclude that calculations based on Rock-Eval pyrolysis overestimate expulsion factors and petroleum charge because low pressure and rapid removal of thermally cracked products by the carrier gas retards cross-linking and pyrobitumen formation that is otherwise favored by natural burial maturation. Expulsion factors and petroleum charge based on hydrous pyrolysis may also be high

Studies on bound residues of 14C-malathion in soil

International Nuclear Information System (INIS)

Hussain, A.; Azam, F.; Malik, K.A.

1984-01-01

The extractability and formation of bound 14 C-labelled residues in clay loam soil under laboratory conditions were investigated with malathion. 14 C-malathion rapidly decomposed to 14 CO 2 . Twelve days after treatment 56% of the applied dose was lost as 14 CO 2 . Methanol gave the highest extraction efficiency; 6% of the applied radiocarbon was extractable while bound residues amounted to 38%. The soil containing 14 C-labelled residues was fractionated into humic acid, fulvic acid and humin fractions. These fractions contained 7.83%, 16.81% and 19.36%, respectively of applied radiocarbon. (author)

Petroleum question. Die Oelfrage

Energy Technology Data Exchange (ETDEWEB)

Mommer, B

1983-01-01

The author analyses the development of the world petroleum market and its pricing factors to the present on the basis of the theory of ground rent, in which the part played by absolute ground rent, differential rent, and free and national state property in the capitalist mode of production is determined. His investigation of economic policy traces the absorbing history of the petroleum production and policy of the United States of America, which for so long governed the world market, the development of Venezuela into a petroleum country (whose true history is here revealed for the first time), the penetration of the middle East by the international petroleum leaseholders' capital and their cartel, the formation of the OPEC, and finally the 'victory' of the lather over the petroleum combines in the international petroleum crisis of 1970-1973. The book closes with a survey at the start of the 80s and an outlook into the foreseeable future. What is really hidden behind the quarrels about prices, profit, taxes, royalties, franchise agreements, production quotas, nationalization and so forth and behind the economic, political, and even moral arguments of the parties concerned turns out to be the fight of the petroleum ground proprietors for the ground rent - but to win a victory in this fight means ultimately to face its limitations, too. Blindness to the economic and political importance of ground rent, right from the theoretical approach, also created a major cause of the false diagnoses and forecasts on the petroleum market western economic scientists were misled into, and thus of the surprise effect that came in the form of the petroleum crisis of the early 1970s.

Indicators on the world petroleum markets

International Nuclear Information System (INIS)

2000-10-01

This paper presents tendencies of the petroleum industry market. It analyses the petroleum demand and supply, the prices elaboration, the petroleum market and the OPEC objective, the third petroleum crisis of the year 2000 and gives some data concerning the petroleum market. (A.L.B.)

Figures of the petroleum industry

Energy Technology Data Exchange (ETDEWEB)

1978-01-01

The statistic tables give informations about: Reserves and production of petroleum and natural gas, supply of crude petroleum in the Federal Republic of Germany, pipelines, tanker ships, petroleum refineries, petroleum consumption, storage and distribution, automobiles, prices, taxis and energy consumption. The data compilations are primarily given for the Federal Republic of Germany.

Assessment of intra-species diversity among strains of Acinetobacter baumannii isolated from sites contaminated with petroleum hydrocarbons

International Nuclear Information System (INIS)

Manab Sarma, P.; Bhattacharya, D.; Krishnan, S.; Lal, B.

2004-01-01

Intra-species diversity among Acinetobacter baumannii strains isolated from crude oil-contaminated soils from different geographic regions in India was assessed, including their capability to degrade different fractions of total petroleum hydrocarbons. A total of 96 strains were isolated from five different sites. Of the 96 isolates, 25 strains were identified as Acinetobacter baumannii; all of these strains were biochemically profiled and grouped into eight phenovars on the basis of multivariate analysis of their substrate utilization profiles. All strains were able to degrade the total petroleum hydrocarbon fractions of crude oil. Intraspecies relatedness among the 25 strains was determined using tRNA intergenic spacer length polymorphism. Specific variants among the strains with different degradation capacities for different fractions of crude oil were detected. Environmental influences that cause intra-species diversity, such as functional resilience, within the selected strains of A. baumannii were also noted. It is suggested that such diversities may make it possible to select contaminant-specific strains for efficient biotechnological strategies in environmental remediation. 19 refs., 4 tabs., 3 figs

Assessment of intra-species diversity among strains of Acinetobacter baumannii isolated from sites contaminated with petroleum hydrocarbons

Energy Technology Data Exchange (ETDEWEB)

Manab Sarma, P.; Bhattacharya, D.; Krishnan, S. [TERI School of Advanced Studies, Center of Bioresources and Biotechnology, New Delhi (India); Lal, B. [TERI School of Advanced Studies, Microbial Biotechnology Division, New Delhi (India)

2004-06-01

Intra-species diversity among Acinetobacter baumannii strains isolated from crude oil-contaminated soils from different geographic regions in India was assessed, including their capability to degrade different fractions of total petroleum hydrocarbons. A total of 96 strains were isolated from five different sites. Of the 96 isolates, 25 strains were identified as Acinetobacter baumannii; all of these strains were biochemically profiled and grouped into eight phenovars on the basis of multivariate analysis of their substrate utilization profiles. All strains were able to degrade the total petroleum hydrocarbon fractions of crude oil. Intraspecies relatedness among the 25 strains was determined using tRNA intergenic spacer length polymorphism. Specific variants among the strains with different degradation capacities for different fractions of crude oil were detected. Environmental influences that cause intra-species diversity, such as functional resilience, within the selected strains of A. baumannii were also noted. It is suggested that such diversities may make it possible to select contaminant-specific strains for efficient biotechnological strategies in environmental remediation. 19 refs., 4 tabs., 3 figs.

HYDROGENATION OF TOLUENE ON Ni-Co-Mo SUPPORTED ...

African Journals Online (AJOL)

HOD

Keywords: Hydro treating catalysts; Hydrogenation; Toluene conversion; Surface area; Pore diameter. 1. ... decades in refineries to upgrade heavy oil fractions and residue. Metals often ...... "Hydroprocessing of heavy petroleum feeds: Tutorial ...

Petroleum hydrocarbon concentrations in ten commercial fish species along Tamilnadu coast, Bay of Bengal, India.

Science.gov (United States)

Veerasingam, S; Venkatachalapathy, R; Raja, P; Sudhakar, S; Rajeswari, V; Asanulla, R Mohamed; Mohan, R; Sutharsan, P

2011-05-01

The aim of the present study was to evaluate the distribution of petroleum hydrocarbons in ten commercial fish species and water samples in three estuaries along Tamilnadu coast, Bay of Bengal, India. Fish and water samples collected from Tamilnadu coast, India, were extracted and analyzed for petroleum hydrocarbons by ultraviolet fluorescence (UVF) spectroscopy. The petroleum hydrocarbon concentration (PHC) in coastal waters and fish species varied between 2.28 and 14.02 μg/l and 0.52 and 2.05 μg/g, respectively. The highest PHC concentration was obtained in Uppanar estuarine waters (14.02 ± 0.83) and the lowest was observed in Vellar estuarine waters (2.28 ± 0.25). Among the ten fish species, Sardinella longiceps have high PHC concentration from all the locations. This study suggests that S. longiceps can be used as a good biological indicator for petroleum hydrocarbon pollution in water. The concentration of petroleum hydrocarbons in coastal waters along Tamilnadu coast is markedly higher than that in the background, but there is no evidence for its increase in fish of this region. From a public health point, petroleum hydrocarbon residue levels in all fish samples analyzed in this study are considerably lower than the hazardous levels. At present, as Tamilnadu coastal area is in a rapid development stage of new harbour, chemical industries, power plants, oil exploration and other large-scale industries, further assessment of petroleum hydrocarbons and the various hydrodynamic conditions acting in the region are to be studied in detail and continuous pollution monitoring studies should be conducted for improving the aquatic environment. The results will also be useful for pollution monitoring program along the coastal region and also to check the levels of petroleum hydrocarbons.

Yugoslavian Petroleum Refinery development program

International Nuclear Information System (INIS)

Ocic, Ozren

1999-01-01

This paper shows the analysis of the world petroleum industry development, being an important factor in planning the development of the Yugoslav petroleum industry and Pancevo Petroleum Refinery, as well. Then Yugoslav petroleum industry development is analysed, including the appropriate balances of crude oil production and crude oil products consumption. The way of realizing the basic targets are also proposed. Likewise, the analysis of the condition within West European refineries has been conducted, from the aspects of technology, energy consumption and environmental protection and the same analysis for Pancevo Petroleum Refinery has been presented, too. The analysis of the condition within the refineries in the European Union countries and comparing it with the condition within Pancevo Petroleum Refinery, makes it mainly possible to recognize the development programmes which should be realized in order that Pancevo Petroleum Refinery could reach the refining level of the EU countries. (Original)

Facts 2010 - The Norwegian petroleum sector

Energy Technology Data Exchange (ETDEWEB)

2010-07-01

The publication provides a general overview of information regarding the petroleum activities on the Norwegian continental shelf. Content; Foreword; The petroleum sector - Norway's largest industry; Organisation of Norwegian petroleum activity; Government petroleum revenues; Exploration activities; Development and operations; Norwegian gas exports; Decommissioning; Research, technology and industrial development; Environmental considerations in the Norwegian petroleum sector; Petroleum resources; Fields in production; Fields under development; Future developments; Fields where production has ceased; Pipelines and onshore facilities. (AG)

Petroleum refining and air quality

International Nuclear Information System (INIS)

Raimbault, C.

1992-01-01

This paper studies the methods which may be developed in petroleum refineries or during petroleum products using for air pollution abatement: petroleum products desulfurization, lead elimination in gasoline and catalytic converters to reduce sulfur dioxide and nitrogen oxides in exhaust gases. Investments and costs estimation to adapt petroleum refineries for environment protection is also given. 1 ref., 6 figs., 6 tabs

Facts 2011 - The Norwegian petroleum sector

Energy Technology Data Exchange (ETDEWEB)

2011-07-15

The publication provides a general overview of information regarding the petroleum activities on the Norwegian continental shelf. Content; Foreword; The petroleum sector - Norway's largest industry; Organisation of Norwegian petroleum activity; Government petroleum revenues; Exploration activities; Development and operations; Norwegian gas exports; Decommissioning; Research, technology and industrial development; Environmental considerations in the Norwegian petroleum sector; Petroleum resources; Fields in production; Fields under development; Future developments; Fields where production has ceased; Pipelines and onshore facilities. (AG)

Facts 2010 - The Norwegian petroleum sector

Energy Technology Data Exchange (ETDEWEB)

2010-07-01

The publication provides a general overview of information regarding the petroleum activities on the Norwegian continental shelf. Content; Foreword; The petroleum sector - Norway's largest industry; Organisation of Norwegian petroleum activity; Government petroleum revenues; Exploration activities; Development and operations; Norwegian gas exports; Decommissioning; Research, technology and industrial development; Environmental considerations in the Norwegian petroleum sector; Petroleum resources; Fields in production; Fields under development; Future developments; Fields where production has ceased; Pipelines and onshore facilities. (AG)

Carbon-13 isotopic composition of distillation fractions of some Egyptian crude oils

International Nuclear Information System (INIS)

Aly, A.I.M.; Hamza, M.S.; Abd Elsamie, S.G.

1991-01-01

13 C/ 13 C ratios were determined for some crude oil fields in the Gulf of Suez and Western Desert provinces. The crude oil was subjected to distillation at atmospheric pressure and subsequently under vacuum. Distillation fractions were collected at 25 degree C intervals. Carbon-13 content of these distillation fractions showed some differences in the degree of isotopic fractionation. The results were interpreted in view of the age of the source rocks and the degree of maturation process. The carbon-13 content of distillation fractions may be helpful in revealing petroleum mechanisms which can be exploited in exploration.4 fig

2005 yearly days of petroleum

International Nuclear Information System (INIS)

Constant, R.; Susbielles, G.

2005-01-01

14 articles are gathered in this data sheet; they deal with the opening address of the 2005 petroleum days; the hydrocarbons: the evolutive resource; the para-petroleum engineers and the Europe; the speech of Mr Francois Loos; the Shell global scenarios to 2025; the evolution of the gas resource and its uses; the French para-petroleum industry; Bernard Bensaid, Corinne Sagary, Armelle Saniere, economic studies, IFP; the contribution of the innovation and of the technology in the diversification of the hydrocarbons supply; innovation and diversification of the petroleum resource: the point of view of Total; research, development and diversification of the petroleum resource; innovation in services companies; innovation in study and development and engineering; the closing address of the 2005 petroleum days. (O.M.)

Logistics aspects of petroleum pipeline operations

Directory of Open Access Journals (Sweden)

W. J. Pienaar

2010-11-01

Full Text Available The paper identifies, assesses and describes the logistics aspects of the commercial operation of petroleum pipelines. The nature of petroleum-product supply chains, in which pipelines play a role, is outlined and the types of petroleum pipeline systems are described. An outline is presented of the nature of the logistics activities of petroleum pipeline operations. The reasons for the cost efficiency of petroleum pipeline operations are given. The relative modal service effectiveness of petroleum pipeline transport, based on the most pertinent service performance measures, is offered. The segments in the petroleum-products supply chain where pipelines can play an efficient and effective role are identified.

Identification of petroleum pollution sources

International Nuclear Information System (INIS)

Begak, O.Yu.; Syroezhko, A.M.

2001-01-01

A possibility of preliminary identification of petroleum pollution sources was investigated on specimens of the Khanty-Mansi autonomous district six deposits and specimens of soil and water polluted by these petroleums. Investigations were conducted using IR Fourier spectroscopy and gamma spectrometry, as well as methods of chromato-mass spectrometry and capillary gas liquid chromatography. Every of studied samples of petroleum from different deposits have an individual radiation impression. Insignificant total content of radionuclides in samples is specific to the Khanty-Mansi petroleum region. Gamma spectrometry admits to identify potential source of petroleum pollution using radionuclides of uranium and thorium series [ru

Generalized continued fractions and ergodic theory

International Nuclear Information System (INIS)

Pustyl'nikov, L D

2003-01-01

In this paper a new theory of generalized continued fractions is constructed and applied to numbers, multidimensional vectors belonging to a real space, and infinite-dimensional vectors with integral coordinates. The theory is based on a concept generalizing the procedure for constructing the classical continued fractions and substantially using ergodic theory. One of the versions of the theory is related to differential equations. In the finite-dimensional case the constructions thus introduced are used to solve problems posed by Weyl in analysis and number theory concerning estimates of trigonometric sums and of the remainder in the distribution law for the fractional parts of the values of a polynomial, and also the problem of characterizing algebraic and transcendental numbers with the use of generalized continued fractions. Infinite-dimensional generalized continued fractions are applied to estimate sums of Legendre symbols and to obtain new results in the classical problem of the distribution of quadratic residues and non-residues modulo a prime. In the course of constructing these continued fractions, an investigation is carried out of the ergodic properties of a class of infinite-dimensional dynamical systems which are also of independent interest

Microbial dynamics in petroleum oilfields and their relationship with physiological properties of petroleum oil reservoirs.

Science.gov (United States)

Varjani, Sunita J; Gnansounou, Edgard

2017-12-01

Petroleum is produced by thermal decay of buried organic material over millions of years. Petroleum oilfield ecosystems represent resource of reduced carbon which favours microbial growth. Therefore, it is obvious that many microorganisms have adapted to harsh environmental conditions of these ecosystems specifically temperature, oxygen availability and pressure. Knowledge of microorganisms present in ecosystems of petroleum oil reservoirs; their physiological and biological properties help in successful exploration of petroleum. Understanding microbiology of petroleum oilfield(s) can be used to enhance oil recovery, as microorganisms in oil reservoirs produce various metabolites viz. gases, acids, solvents, biopolymers and biosurfactants. The aim of this review is to discuss characteristics of petroleum oil reservoirs. This review also provides an updated literature on microbial ecology of these extreme ecosystems including microbial origin as well as various types of microorganisms such as methanogens; iron, nitrate and sulphate reducing bacteria, and fermentative microbes present in petroleum oilfield ecosystems. Copyright © 2017 Elsevier Ltd. All rights reserved.

The world petroleum industry

International Nuclear Information System (INIS)

Mons, L.

2005-01-01

This study proposes a global vision of the petroleum industry, a precise and well argued state of the art of the petroleum markets. It defines the strategical challenges which the petroleum companies are exposed and allows to anticipate the sector evolutions. It details the key acts of the last three years, the financial performances of the companies. (A.L.B.)

Phytoremediation of petroleum contaminated soils by Mirabilis Jalapa L. in a greenhouse plot experiment.

Science.gov (United States)

Peng, Shengwei; Zhou, Qixing; Cai, Zhang; Zhang, Zhineng

2009-09-15

Phytoremediation of soils contaminated by organic chemicals is a challenging problem in environmental science and engineering. On the basis of identifying remediation plants from ornamentals, the remediation capability of Mirabilis Jalapa L. to treat petroleum contaminated soil from the Shengli Oil Field in Dongying City, Shandong Province, China was further investigated using a field plot experiment carried out in a greenhouse. The results showed that the average efficiency of removing total petroleum hydrocarbons (TPHs) by M. jalapa over the 127-day culture period was high, up to 41.61-63.20%, when the removal rate by natural attenuation was only 19.75-37.92%. The maximum reduction occurred in the saturated hydrocarbon fraction compared with other components of petroleum contaminants. According to the qualitative and quantitative parameters including plant height, fresh weight, dry weight, root length, root weight and visual stress symptoms, it was indicated that M. jalapa had a peculiar tolerance to petroleum contamination and could effectively promote the degradation of TPHs when the concentration of petroleum hydrocarbons in soil was equal to and lower than 10,000 mg/kg. The population of living microorganisms in the planted soil could be also adaptive to contaminated soil. On the whole, M. jalapa is a widely spread species that can be effectively applied to phytoremediation of contaminated soil.

Polymer science applied to petroleum production; Ciencia de polimeros aplicada a producao de petroleo

Energy Technology Data Exchange (ETDEWEB)

Lucas, Elizabete F.; Mansur, Claudia R.E.; Garreto, Maria S.E.; Honse, Siller O.; Mazzeo, Claudia P.P. [Universidade Federal do Rio de Janeiro/ Instituto de Macromoleculas/ Laboratorio de Macromoleculas e Coloides na Industria de Petroleo, Rio de Janeiro, RJ (Brazil)], e-mail: elucas@ima.ufrj.br

2011-07-01

The petroleum production comprises several operations, from well drilling to oil and water treatment, in which polymer science is applied. This work is focused in the phase behavior of asphaltenes that can be evaluated by precipitation tests and particle size determination. Recent researches show that the petroleum can be diluted with a specific model solvent, without causing any changes on asphaltenes phase behavior, and that a representative model system can be obtained if asphaltenes could be extracted using n-alkane as low as C1. The phase behavior of asphaltenes directly depends on the solubility parameter, which can be estimated for petroleum and asphaltenic fractions by microcalorimetry. More polar asphaltenes are not completely stabilized by less polar molecules, and this affects the stability of the A/O emulsions. There is a relationship between the amount of polar groups in the polymer chain and its capability in stabilizing/flocculating the asphaltenes, which interferes in the asphaltenes particle sizes. (author)

Pilot remediation of sediment from the Petroleum harbour in Amsterdam

International Nuclear Information System (INIS)

Hakstege, A.L.; Geldermalsen, L.A. van

1998-01-01

The Petroleum Harbour project is the third pilot remediation, which was carried out within the framework of POSW (the national development programme for treatment processes of polluted sediments). The main objectives of the pilot remediation are: to demonstrate the biological treatment of dredged materials on a practical scale; and to gain knowledge and experience for the future remediation of the total Petroleum harbour. A strict tender procedure was carefully executed in order to select the most effective and 'state of the art' biodegradation technology. The selected remediation chain was a combination of 'standard' soil treatment technology and newly developed biotechnology. Dredging, biotechnological treatment and the effects of the remediation on the environment were monitored in detail. The quality of the treated sand fraction complied with the Dutch standards for re-use and was actually applied in a project of Rijkswaterstaat. Biodegradation resulted in a substantial decrease of the oil and PAH's contents, but due to the lack of breakdown of a few high-molecular PAH's, the quality requirements of the contract were not achieved. It is concluded that the two main objectives of the project have been attained. Finally some recommendations for the future clean-up of the Petroleum harbour are given. (author)

Results of analyzing natural gas during the use of biochemical processes in a petroleum deposit

Energy Technology Data Exchange (ETDEWEB)

Yulbarisov, E M

1972-01-01

Laboratory and commercial scale experiments with a geobioreagent and the Arlanskii deposit petroleum gave a sharp increase in the content of heavier hydrocarbons, nitrogen, and carbon dioxide in the gas and an increase in the yield of gasoline fraction boiling below 122/sup 0/C. The commercial scale experiments were done in a stratum 1200 m deep during waterflood recovery at 200 kg/cm/sup 2/. A substantial increase in ethane and higher hydrocarbons in the gas and increased petroleum yield were observed, especially after each waterflood. The effect of water was explained by higher activity of the bacteria at a lower concentration of rock salts.

Estimation of residual MSW heating value as a function of waste component recycling

International Nuclear Information System (INIS)

Magrinho, Alexandre; Semiao, Viriato

2008-01-01

Recycling of packaging wastes may be compatible with incineration within integrated waste management systems. To study this, a mathematical model is presented to calculate the fraction composition of residual municipal solid waste (MSW) only as a function of the MSW fraction composition at source and recycling fractions of the different waste materials. The application of the model to the Lisbon region yielded results showing that the residual waste fraction composition depends both on the packaging wastes fraction at source and on the ratio between that fraction and the fraction of the same material, packaging and non-packaging, at source. This behaviour determines the variation of the residual waste LHV. For 100% of paper packaging recycling, LHV reduces 4.2% whereas this reduction is of 14.4% for 100% of packaging plastics recycling. For 100% of food waste recovery, LHV increases 36.8% due to the moisture fraction reduction of the residual waste. Additionally the results evidence that the negative impact of recycling paper and plastic packaging on the LHV may be compensated by recycling food waste and glass and metal packaging. This makes packaging materials recycling and food waste recovery compatible strategies with incineration within integrated waste management systems

Evaluation of some residual bioactivities of microencapsulated Phaseolus lunatus protein fraction with carboxymethylated flamboyant (Delonix regia gum/sodium alginate

Directory of Open Access Journals (Sweden)

Mukthar Sandovai-Peraza

2014-12-01

Full Text Available Recent studies have shown the beneficial effect of peptides, an unexploited source could be Phaseolus lunatus being an important raw material for those functional products in order to improve their utilization. In addition to improve the beneficial effect of bioactive peptides the microencapsulation could be a way to protect the peptides against the environment to which they are exposed. P. lunatus protein fraction (<10 kDa of weight was encapsulated using a blend of carboxymethylated flamboyant gum (CFG and sodium alginate (SA at different concentrations of CaCl2 and hardening times. After in vitro digestion of microcapsules the residual activity, in the intestinal system, both inhibition of agiotensin-converting enzyme (I-ACE and antioxidant activity obtained were in a range of 0.019-0.136 mg/mL and 570.64-813.54 mM of TEAC respectively. The microencapsulation employed CFG/SA blends could be used controlled delivery of peptide fractions with potential use as a nutraceutical or therapeutic agents.

Contribution of chronic petroleum inputs to Narragansett Bay and Rhode Island Sound sediments

Energy Technology Data Exchange (ETDEWEB)

Van Vleet, E S; Quin, J G

1978-05-01

Sediment cores from Narragansett Bay and Rhode Island Sound have been analyzed for petroleum hydrocarbons and compared with a relatively unpolluted sediment core from the Gulf of Maine. The sediments were analyzed for unbound hydrocarbons, hydrocarbons bound or closely associated with humic substances, and residual hydrocarbons bound or closely associated with the clay mineral or kerogen matrix. Results indicated that in general 90-100% of the hydrocarbons were in the unbound form and could be easily extracted with organic solvents. The petroleum hydrocarbons decreased with depth at all stations. Biogenic hydrocarbons (nC/sub 25/, nC/sub 27/, nC/sub 29/, and nC/sub 31/) made up an increasingly greater percentage of the total with increasing depth. The hydrocarbons in the Narragansett Bay sediments and near surface Rhode Island Sound sediments strongly resembled the hydrocarbons previously reported for the Providence River and upper Narragansett Bay. These petroleum-like hydrocarbons were shown to be largely introduced to the river and bay through chronic inputs from a municipal wastewater treatment plant. These hydrocarbons then undergo sedimentation throughout the entire bay and into Rhode Island Sound. Preliminary calculations indicate that over 0.2 million t (tonne) of petroleum hydrocarbons may be transported to the marine environment annually from municipal treatment plants. Most of these hydrocarbons appear to accumulate in estuarine and coastal sediments.

Bioremediation of petroleum hydrocarbons in soil environments

International Nuclear Information System (INIS)

Rowell, M.J.; Ashworth, J.; Qureshi, A.A.

1992-12-01

The bioremediation of petroleum hydrocarbons in soil environments was reviewed via a literature survey and discussions with workers in relevant disciplines. The impacts of hydrocarbons on soil are discussed along with a range of methods available to assist in their decomposition by soil microorganisms. The range of petroleum-based materials considered includes conventional and synthetic crude oils, refined oils, sludges, asphalts and bitumens, drilling mud residues, creosote tars, and some pesticides. The degradability of hydrocarbons largely depends upon their aqueous solubility and their adsorption on soil surfaces and, therefore, is related to their molecular structures. The ease of decomposition decreases with increasing complexity of structure, in the order aliphatics > aromatics > heterocyclics and asphaltenes (most recalcitrant). Most soils contain an adequate population of microorganisms and hence bioaugmentation may only be needed in special circumstances. Decomposition is fastest in soils where the hydrocarbon loading rate, aeration, nutrition, moisture, and pH are all optimized. At spill sites there is little control over the application rate, although containment measures can assist in either limiting contamination or distributing it more evenly. The enhancement of bioremediation is discussed in light of all these factors. Other techniques such as enhanced aeration, hydrocarbon decomposition by anaerobic processes, surfactants, and burning are also discussed. 211 refs., 11 figs., 10 tabs

Bioremediation of petroleum hydrocarbons in soil environments

Energy Technology Data Exchange (ETDEWEB)

Rowell, M J; Ashworth, J; Qureshi, A A

1992-12-01

The bioremediation of petroleum hydrocarbons in soil environments was reviewed via a literature survey and discussions with workers in relevant disciplines. The impacts of hydrocarbons on soil are discussed along with a range of methods available to assist in their decomposition by soil microorganisms. The range of petroleum-based materials considered includes conventional and synthetic crude oils, refined oils, sludges, asphalts and bitumens, drilling mud residues, creosote tars, and some pesticides. The degradability of hydrocarbons largely depends upon their aqueous solubility and their adsorption on soil surfaces and, therefore, is related to their molecular structures. The ease of decomposition decreases with increasing complexity of structure, in the order aliphatics > aromatics > heterocyclics and asphaltenes (most recalcitrant). Most soils contain an adequate population of microorganisms and hence bioaugmentation may only be needed in special circumstances. Decomposition is fastest in soils where the hydrocarbon loading rate, aeration, nutrition, moisture, and pH are all optimized. At spill sites there is little control over the application rate, although containment measures can assist in either limiting contamination or distributing it more evenly. The enhancement of bioremediation is discussed in light of all these factors. Other techniques such as enhanced aeration, hydrocarbon decomposition by anaerobic processes, surfactants, and burning are also discussed. 211 refs., 11 figs., 10 tabs.

Pilot-scale bioremediation of a petroleum hydrocarbon-contaminated clayey soil from a sub-Arctic site

Energy Technology Data Exchange (ETDEWEB)

Akbari, Ali; Ghoshal, Subhasis, E-mail: subhasis.ghoshal@mcgill.ca

2014-09-15

Highlights: • Aeration and moisture addition alone caused extensive hydrocarbon biodegradation. • 30-day slurry reactor remediation endpoints attained in 385 days in biopiles. • High nitrogen concentrations inhibited hydrocarbon degradation. • Inhibition of biodegradation linked to lack of shifts in soil microbial community. - Abstract: Bioremediation is a potentially cost-effective solution for petroleum contamination in cold region sites. This study investigates the extent of biodegradation of petroleum hydrocarbons (C16–C34) in a pilot-scale biopile experiment conducted at 15 °C for periods up to 385 days, with a clayey soil, from a crude oil-impacted site in northern Canada. Although several studies on bioremediation of petroleum hydrocarbon-contaminated soils from cold region sites have been reported for coarse-textured, sandy soils, there are limited studies of bioremediation of petroleum contamination in fine-textured, clayey soils. Our results indicate that aeration and moisture addition was sufficient for achieving 47% biodegradation and an endpoint of 530 mg/kg for non-volatile (C16–C34) petroleum hydrocarbons. Nutrient amendment with 95 mg-N/kg showed no significant effect on biodegradation compared to a control system without nutrient but similar moisture content. In contrast, in a biopile amended with 1340 mg-N/kg, no statistically significant biodegradation of non-volatile fraction was detected. Terminal Restriction Fragment Length Polymorphism (T-RFLP) analyses of alkB and 16S rRNA genes revealed that inhibition of hydrocarbon biodegradation was associated with a lack of change in microbial community composition. Overall, our data suggests that biopiles are feasible for attaining the bioremediation endpoint in clayey soils. Despite the significantly lower biodegradation rate of 0.009 day{sup −1} in biopile tank compared to 0.11 day{sup −1} in slurry bioreactors for C16–C34 hydrocarbons, the biodegradation extents for this fraction

Ex-USSR: petroleum activities in 1991

International Nuclear Information System (INIS)

1992-01-01

This paper gives statistical data on economy and petroleum industry in ex-USSR: Primary energy production and consumption (coal, petroleum, natural gas, primary power), petroleum and natural gas reserves, drilling activity, exports and imports of petroleum products, refining capacity. 2 figs., 14 tabs

Intrinsic bacterial biodegradation of petroleum contamination demonstrated in situ using natural abundance, molecular-level 14C analysis

International Nuclear Information System (INIS)

Slater, G.F.; Nelson, R.K.; Kile, B.M.; Reddy, C.M.

2006-01-01

Natural abundance, molecular-level C 14 analysis was combined with comprehensive gas chromatography (GC x GC) to investigate, in situ, the role of intrinsic biodegradation in the loss of petroleum hydrocarbons from the rocky, inter-tidal zone impacted by the Bouchard 120 oil spill. GC x GC analysis indicated accelerated losses of n-alkane components of the residual petroleum hydrocarbons between day 40 and day 50 after the spill. 14 C analysis of bacterial phospholipid fatty acids (PLFA) from the impacted zone on day 44 showed that the polyunsaturated fatty acids attributed to the photoautotrophic component of the microbial community had the same ( 14 C as the local dissolved inorganic carbon (DIG), indicating that this DIG was their carbon source. In contrast there was significant (C depletion in the saturated and mono-unsaturated PLFA indicating incorporation of petroleum carbon. This correlation between the observed accelerated n-alkane losses and microbial incorporation of (C-depleted carbon directly demonstrated, in situ, that intrinsic biodegradation was affecting the petroleum. Since the majority of organic contaminants originate from petroleum feed-stocks, in situ molecular-level 14 C analysis of microbial PLFA can provide insights into the occurrence and pathways of biodegradation of a wide range of organic contaminants. (Author)

Treatment of products from petroleum, shale, coal, lignite, etc

Energy Technology Data Exchange (ETDEWEB)

Jevanoff, V

1952-06-20

An improved process is described for treating with sodium plumbite all the products derived from crude petroleum, bituminous shale, coal, lignite, peat, etc., such as gasoline, solvents, lamp oil, gas oil, fuels, etc; the process being essentially characterized by the fact that it consists first in washing the product to be refined with a soda wash; submitting it to a treatment with sodium plumbite, without addition of sulfur, then to eliminate the sulfur plumbite compounds resulting in the treated product, using either redistillation to eliminate products remaining in the residue or filtration over an absorbing material such as active carbon, decolorizing earths.

The hidden face of the petroleum

International Nuclear Information System (INIS)

Laurent, E.

2006-02-01

For the first time, a book reveals what that was hidden to the public opinions: why the petroleum crisis of 1973 what only a manipulation, an arrangement between the OPEC and the petroleum companies, why the data concerning the petroleum reserves are wrong and increased by the producers countries, how Washington used the Saudi petroleum weapon to create the Soviet Union fall, and why from march 2001 maps of the Iraq (where were drawn the future petroleum explorations) were working documents for the vice President Cheney and petroleum managers for the ''secret society''. (A.L.B.)

Petroleum industry in CIS

International Nuclear Information System (INIS)

Vaillaud, P.

1992-01-01

This paper gives statistical data on petroleum and natural gas industry in USSR and in Eastern Europe: crude oil and gas production, petroleum and natural gas deposits, exports, fuel consumption, pipelines network (total length, compressor or pump stations), petroleum refineries. This paper describes also air pollution (carbon dioxide and sulfur dioxide) and Environmental effects of coal and lignite using in fossil power plants in Eastern Europe. 17 figs., 7 tabs

Investigation of the toxicokinetics of petroleum hydrocarbon distillates with the earthworm Eisenia andrei.

Science.gov (United States)

Cermak, Janet; Stephenson, Gladys; Birkholz, Detlef; Dixon, D George

2013-04-01

The Canada-wide standards for petroleum hydrocarbons in soils regulate petroleum hydrocarbons based on four distillate ranges: F1 (C6-C10), F2 (>C10-C16), F3 (>C16-C34), and F4 (>C34). Previous toxicity tests with earthworms and F2, as well as two subfractions of F3, F3a (>C16-C23) and F3a (>C23-C34), indicate that test durations might not be sufficiently long to reach threshold effect concentrations, likely because of the differing toxicokinetics for each distillate. A study was conducted to determine the toxicokinetics of both aliphatic and aromatic fractions of F2, F3a, and F3b with the earthworm Eisenia andrei. Peak accumulation curves were observed for F2 aliphatics and aromatics and F3a aromatics, likely as a result of changes in exposure concentration over the test duration via loss or a decrease in the bioavailable fraction. Biota-soil accumulation factors were >1 for total F2 aliphatics and aromatics and F3a aromatics as well as for several individual polyaromatic hydrocarbons for each distillate. Aromatics were disproportionately accumulated over aliphatics and were the main contributors to toxicity; therefore, aromatics and aliphatics should be regulated separately. The toxicokinetics were used to interpret previous toxicity data. Higher molecular weight distillates need longer-than-standard test durations to determine toxicity, so toxicity test results from fixed, standard-duration tests are not strictly comparable for these petroleum distillates. Copyright © 2013 SETAC.

Marks on the petroleum fiscality

International Nuclear Information System (INIS)

2007-02-01

This document offers some marks on the petroleum fiscality in France: the taxes as the 'accises' and the 'TVA', the part of the taxes in the sale price at the service station, the comparison with other countries of Europe, the tax revenues and the Government budget. It provides also marks on the fuels prices formation (margins), the world petroleum markets (supply and demand) and the part of the petroleum companies on the petroleum market. (A.L.B.)

Apparatus for extracting petroleum

Energy Technology Data Exchange (ETDEWEB)

Coogan, J

1921-01-18

An apparatus for extracting petroleum from petroleum bearing sand or shale is described comprising a container for liquids, the container being divided into a plurality of compartments, an agitator mounted within the container and below the liquid level and having its forward end opening into one of the compartments, means for delivering sand or shale to the forward end of the agitator, means for subjecting the sand or shale to the action of a solvent for the petroleum while the sand or shale is being agitated and is submerged, the first-mentioned compartment being adapted to receive the extracted petroleum and means for removing the treated sand or shale from adjacent the rear end of the agitator.

The new challenges of petroleum

International Nuclear Information System (INIS)

Gernelle, E.

2006-02-01

Petroleum in in the center of our civilization: abundant, easy to use and energy powerful, it is used almost everywhere: transports, lighting, space heating, plastics, fertilizers, cloth industry etc. The 'black-gold' is the object of all stakes, from richness to power. However, petroleum is also at the origin of many evils: pollution, corruption, violence. Today, petroleum is a source of worries: how long will it last? How long will we be able to stand its impacts on environment? This book shades light on all these questions and supplies some concrete elements about this energy source. Content: technological challenges of petroleum; producers: powers and risks; consumers' dependence; to learn more about petroleum. (J.S.)

Fundamentals of Petroleum.

Science.gov (United States)

Bureau of Naval Personnel, Washington, DC.

Basic information on petroleum is presented in this book prepared for naval logistics officers. Petroleum in national defense is discussed in connection with consumption statistics, productive capacity, world's resources, and steps in logistics. Chemical and geological analyses are made in efforts to familiarize methods of refining, measuring,…

Fractionation of Pb and Cu in the fine fraction (landfill.

Science.gov (United States)

Kaczala, Fabio; Orupõld, Kaja; Augustsson, Anna; Burlakovs, Juris; Hogland, Marika; Bhatnagar, Amit; Hogland, William

2017-11-01

The fractionation of metals in the fine fraction (landfill was carried out to evaluate the metal (Pb and Cu) contents and their potential towards not only mobility but also possibilities of recovery/extraction. The fractionation followed the BCR (Community Bureau of Reference) sequential extraction, and the exchangeable (F1), reducible (F2), oxidizable (F3) and residual fractions were determined. The results showed that Pb was highly associated with the reducible (F2) and oxidizable (F3) fractions, suggesting the potential mobility of this metal mainly when in contact with oxygen, despite the low association with the exchangeable fraction (F1). Cu has also shown the potential for mobility when in contact with oxygen, since high associations with the oxidizable fraction (F3) were observed. On the other hand, the mobility of metals in excavated waste can be seen as beneficial considering the circular economy and recovery of such valuables back into the economy. To conclude, not only the total concentration of metals but also a better understanding of fractionation and in which form metals are bound is very important to bring information on how to manage the fine fraction from excavated waste both in terms of environmental impacts and also recovery of such valuables in the economy.

Canadian petroleum history bibliography

Energy Technology Data Exchange (ETDEWEB)

Cass, D.

2003-09-27

The Petroleum History Bibliography includes a list of more than 2,000 publications that record the history of the Canadian petroleum industry. The list includes books, theses, films, audio tapes, published articles, company histories, biographies, autobiographies, fiction, poetry, humour, and an author index. It was created over a period of several years to help with projects at the Petroleum History Society. It is an ongoing piece of work, and as such, invites comments and additions.

Multi-solid model modified to predict paraffin in petroleum fluids at high temperatures and pressures

International Nuclear Information System (INIS)

Escobar Remolina, Juan Carlos M; Barrios Ortiz, Wilson; Santoyo Ramirez Gildardo

2009-01-01

A thermodynamic structure has been modified in order to calculate cloud point, fluidity and amount of precipitated wax under a wide range of temperature conditions, composition, and high pressures. The model is based on a combination of ideal solution concepts, fluid characterization, and formation of multiple solid phases using Cubic State Equations. The experimental data utilized for testing the prediction capacity and potentiality of a model exhibit different characteristics: continuous series synthetic systems of heavy alkanes, discontinuous series, and dead or living petroleum fluids with indefinite fractions such as C7+, C10+, C20+, and C30+. The samples were taken from the literature, petroleum fluids from the main Colombian reservoirs, and some samples of Bolivian fluids. Results presented in this paper show the minimum standard deviations between experimental data and data calculated with a model. This allows a progress in decision-making processes for flow assurance in reservoirs, wells, and surface facilities in the petroleum industry.

Petroleum distillates suppress in vitro metabolic activation: higher [S-9] required in the Salmonella/microsome mutagenicity assay.

Science.gov (United States)

Carver, J H; Machado, M L; MacGregor, J A

1985-01-01

To determine if standard conditions used in the Salmonella/mammalian microsome mutagenicity assay could reliably screen complex petroleum samples, two high-boiling (700-1,070 degrees F) distillates and their separated aromatic fractions were tested. The initial mutagenic activities were inconsistent with the samples' known polyaromatic hydrocarbon (PAH) contents and observed potencies in a dermal carcinogenesis bioassay. A significant mutagenic response was observed only at S-9 concentrations 5 to 10 times higher than those used in the standard assay, supporting the use of elevated levels of S-9 in the Salmonella/microsome assay to assess the carcinogenic potential of petroleum-derived materials. All four samples masked the expected mutagenic activity of added PAHs (benzo[a]pyrene and perylene). Data suggested that petroleum distillates suppress the functional efficacy of the S-9; possible mechanisms are discussed.

Alkali activation processes for incinerator residues management.

Science.gov (United States)

Lancellotti, Isabella; Ponzoni, Chiara; Barbieri, Luisa; Leonelli, Cristina

2013-08-01

Incinerator bottom ash (BA) is produced in large amount worldwide and in Italy, where 5.1 millionstons of municipal solid residues have been incinerated in 2010, corresponding to 1.2-1.5 millionstons of produced bottom ash. This residue has been used in the present study for producing dense geopolymers containing high percentage (50-70 wt%) of ash. The amount of potentially reactive aluminosilicate fraction in the ash has been determined by means of test in NaOH. The final properties of geopolymers prepared with or without taking into account this reactive fraction have been compared. The results showed that due to the presence of both amorphous and crystalline fractions with a different degree of reactivity, the incinerator BA geopolymers exhibit significant differences in terms of Si/Al ratio and microstructure when reactive fraction is considered. Copyright © 2013 Elsevier Ltd. All rights reserved.

Tainting by short-term exposure of Atlantic salmon to water soluble petroleum hydrocarbons

International Nuclear Information System (INIS)

Ackman, R.G.; Heras, H.

1992-01-01

Experiments were conducted to examine the extent of tainting of salmon by exposure to the soluble fraction of petroleum hydrocarbons. The experiments were conducted on Atlantic salmon in tanks containing seawater artificially contaminated at three different concentrations with the soluble fraction of a North Sea crude. The salmon flesh was analyzed by gas chromatography and taste tests were conducted on cooked salmon samples to determine the extent of tainting. Salmon in control tanks with uncontaminated seawater had muscle accumulations of total hydrocarbons of ca 1 ppM. The muscle accumulations of total hydrocarbons in the salmon were 13.5 ppM, 25.6 ppM, and 31.3 ppM for water soluble fraction concentrations of 0.45, 0.87, and 1.54 ppM respectively. The threshold for taint was clearly inferred to be less than 0.45 ppM of water soluble fraction. 18 refs., 2 figs

Analysis of petroleum contaminated soils by spectral modeling and pure response profile recovery of n-hexane

International Nuclear Information System (INIS)

Chakraborty, Somsubhra; Weindorf, David C.; Li, Bin; Ali, Md. Nasim; Majumdar, K.; Ray, D.P.

2014-01-01

This pilot study compared penalized spline regression (PSR) and random forest (RF) regression using visible and near-infrared diffuse reflectance spectroscopy (VisNIR DRS) derived spectra of 164 petroleum contaminated soils after two different spectral pretreatments [first derivative (FD) and standard normal variate (SNV) followed by detrending] for rapid quantification of soil petroleum contamination. Additionally, a new analytical approach was proposed for the recovery of the pure spectral and concentration profiles of n-hexane present in the unresolved mixture of petroleum contaminated soils using multivariate curve resolution alternating least squares (MCR-ALS). The PSR model using FD spectra (r 2  = 0.87, RMSE = 0.580 log 10  mg kg −1 , and residual prediction deviation = 2.78) outperformed all other models tested. Quantitative results obtained by MCR-ALS for n-hexane in presence of interferences (r 2  = 0.65 and RMSE 0.261 log 10  mg kg −1 ) were comparable to those obtained using FD (PSR) model. Furthermore, MCR ALS was able to recover pure spectra of n-hexane. - Highlights: • We predicted soil petroleum contamination with VisNIR DRS spectra. • We examined 2 spectral pretreatments and 2 multivariate models. • MCR-ALS was used for compositional and spectral resolution of n-hexane. • Penalized spline regression performed best for quantifying soil TPH. • MCR-ALS was promising for resolution of complex soil–petroleum mixture. - Use of VisNIR DRS for rapid quantification of soil TPH and resolution of complex soil petroleum mixtures

The Use of encapsulation techniques as an alternative to employment of soil contaminated by petroleum products in base and sub-base of pavement layers

OpenAIRE

Francisco das Chagas Isael Teixeira Cavalcante

2013-01-01

The petrochemical industry or petroleum deserves special attention because, in practically all stages (drilling, refining, storage and distribution), residues that harm the environment and is a challenge to those responsible for their management are generated. Among the various wastes generated by the oil industry, are the Soils Contaminated by Petroleum Products (SCPD). In Cearà state, the generation of this type of waste is coming from a refinery that is located in Fortaleza city. During ma...

21 CFR 178.3710 - Petroleum wax.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Petroleum wax. 178.3710 Section 178.3710 Food and... and Production Aids § 178.3710 Petroleum wax. Petroleum wax may be safely used as a component of nonfood articles in contact with food, in accordance with the following conditions: (a) Petroleum wax is a...

High paraffin Kumkol petroleum processing under fuel and lubricant petroleum scheme

International Nuclear Information System (INIS)

Nadirov, N.K.; Konaev, Eh.N.

1997-01-01

Technological opportunity of high paraffin Kumkol petroleum processing under the fuel and lubricant scheme with production of lubricant materials in short supply, combustible materials and technical paraffin is shown. Mini petroleum block putting into operation on Kumkol deposit is reasonable economically and raises profitableness of hydrocarbon raw material production. (author)

Canadian Petroleum Products Inst. annual report, 1991

International Nuclear Information System (INIS)

1992-01-01

The Canadian Petroleum Products Institute (CPPI) was created in 1989 as a nonprofit association of Canadian refiners and marketers of petroleum products. In 1991, the Atlantic Petroleum Association, the Quebec Petroleum Association, the Ontario Petroleum Association, the Canada West Petroleum Association, and the Petroleum Association for Conservation of the Canadian Environment (PACE) were integrated into the CPPI. The objective of the CPPI is to serve and represent the refining and marketing sectors of the petroleum industry with respect to environment, health and safety, and business issues. An industry overview is provided, as well as highlights of environmental achievements and challenges, and economics and operations for the year. Lists of CPPI publications, standing committees, and officers are also included. 9 figs

Petroleum Sector (NAICS 324)

Science.gov (United States)

Find relevant environmental regulations for the petroleum industry (NAICS 324), including National Emission Standards for Hazardous Air Pollutants (NESHAP)s for petroleum refineries and gasoline dispensing & effluent guidelines for oil and gas extraction

PETRORISK: a risk assessment framework for petroleum substances.

Science.gov (United States)

Redman, Aaron D; Parkerton, Thomas F; Comber, Mike H I; Paumen, Miriam Leon; Eadsforth, Charles V; Dmytrasz, Bhodan; King, Duncan; Warren, Christopher S; den Haan, Klaas; Djemel, Nadia

2014-07-01

PETRORISK is a modeling framework used to evaluate environmental risk of petroleum substances and human exposure through these routes due to emissions under typical use conditions as required by the European regulation for the Registration, Evaluation, Authorization and Restriction of Chemicals (REACH). Petroleum substances are often complex substances comprised of hundreds to thousands of individual hydrocarbons. The physicochemical, fate, and effects properties of the individual constituents within a petroleum substance can vary over several orders of magnitude, complicating risk assessment. PETRORISK combines the risk assessment strategies used on single chemicals with the hydrocarbon block approach to model complex substances. Blocks are usually defined by available analytical characterization data on substances that are expressed in terms of mass fractions for different structural chemical classes that are specified as a function of C number or boiling point range. The physicochemical and degradation properties of the blocks are determined by the properties of representative constituents in that block. Emissions and predicted exposure concentrations (PEC) are then modeled using mass-weighted individual representative constituents. Overall risk for various environmental compartments at the regional and local level is evaluated by comparing the PECs for individual representative constituents to corresponding predicted no-effect concentrations (PNEC) derived using the Target Lipid Model. Risks to human health are evaluated using the overall predicted human dose resulting from multimedia environmental exposure to a substance-specific derived no-effect level (DNEL). A case study is provided to illustrate how this modeling approach has been applied to assess the risks of kerosene manufacture and use as a fuel. © 2014 SETAC.

Facts 2009 - The Norwegian petroleum sector

Energy Technology Data Exchange (ETDEWEB)

2009-07-01

The publication provides a general overview of information regarding the petroleum activities on the Norwegian continental shelf. Contents: Foreword; The petroleum sector; Norwegian resource management; Government petroleum revenues; Exploration activities; Development and operations; Norwegian gas exports; Decommissioning; Research, technology; Environmental considerations; Petroleum resources; Fields in production; Fields under development; Future developments; Fields where production has ceased; Pipelines and onshore facilities. (AG)

Application of a multimolecular marker approach to fingerprint petroleum pollution in the marine environment

International Nuclear Information System (INIS)

Barakat, Assem O.; Mostafa, Alaa R.; Rullkoetter, Juergen; Hegazi, Abdel Rahman

1999-01-01

In an attempt to investigate the suitability of a multibiological marker approach for defining the origin of petroleum pollution in marine systems, the aliphatic hydrocarbon composition of tar ball samples collected from the beaches of a small island impacted by heavy tar loads were determined by gas chromatography and gas chromatography/mass spectrometry. The tar ball samples, as collected, were at low stages of biodegradation and had diverse physical appearance. The majority of the samples (as many as 7 of the 10) appeared to be heavy fuel oils - possibly Bunker C. The GC traces for the other three tar balls, however, indicated that they were crude oils probably from tanker ballast washings or other non-point sources like the oil entering from the adjacent North Mediterranean. The biomarkers for the sterane and hopane series in these samples, however, had remained unaffected by weathering, and their distributions revealed significant differences among the samples suggesting multiple sources of the tar balls. The tar ball samples could be genetically subdivided into four groups on the basis of their biomarker fingerprints. A marine carbonate or evaporite, hypersaline, anoxic depositional environment of the petroleum source rock for Type I residues could be inferred from the even-carbon-number predominance of n-alkanes, the high relative abundance of gammacerane and the predominance of C 35 relative to C 34 17α(H)-homohopanes. Higher plant contribution and a deltaic environment of source rock deposition could be concluded for Type II residues from the high concentrations of oleanane and diasteranes. On the other hand, Type III residues possessed geochemical characteristics consistent with a normal marine carbonate or evaporite source depositional environment under normal saline, reducing conditions. Finally, type IV residues had biomarker signatures intermediate between Types II and III. (Author)

The distribution and seasonal variations of diffuse fraction

International Nuclear Information System (INIS)

Anane-Fenin, K.

1989-06-01

A moving average approach is used to develop linear and polynomial regression models for the diffuse fraction averaged over 10, 15, 20 and 30 days. The correlations do not appear to be influenced by climate conditions or altitude. It is noted that the correlations vary with season. The time-dependent variations of the diffuse fraction correlations are examined by studying the residual differences between the measured diffuse fraction and those calculated from the over-all best-fit correlation. The residuals exhibit no pronounced pattern leading to the conclusion that the observed seasonal variation is caused by air mass and water vapour and that atmospheric turbidity plays little or no part. (author). 14 refs, 9 figs, 8 tabs

Financing petroleum agreements

International Nuclear Information System (INIS)

Robson, C.J.V.

1994-01-01

This chapter describes the typical type of financing agreements which are currently used to finance North Sea petroleum projects whether they are in the cause of development or have been developed and are producing. It deals with the agreements which are entered into to finance borrowings for petroleum projects on a non-resource or limited resource basis. (UK)

Impact of co-combustion of petroleum coke and coal on fly ash quality: Case study of a Western Kentucky power plant

International Nuclear Information System (INIS)

Hower, James C.; Thomas, Gerald A.; Mardon, Sarah M.; Trimble, Alan S.

2005-01-01

Petroleum coke has been used as a supplement or replacement for coal in pulverized-fuel combustion. At a 444-MW western Kentucky power station, the combustion of nearly 60% petroleum coke with moderate- to high-sulfur Illinois Basin coal produces fly ash with nearly 50% uncombusted petroleum coke and large amounts of V and Ni when compared to fly ash from strictly pulverized coal burns. Partitioning of the V and Ni, known from other studies to be concentrated in petroleum coke, was noted. However, the distribution of V and Ni does not directly correspond to the amount of uncombusted petroleum coke in the fly ash. Vanadium and Ni are preferentially associated with the finer, higher surface area fly ash fractions captured at lower flue gas temperatures. The presence of uncombusted petroleum coke in the fly ash doubles the amount of ash to be disposed, makes the fly ash unmarketable because of the high C content, and would lead to higher than typical (compared to other fly ashes in the region) concentrations of V and Ni in the fly ash even if the petroleum coke C could be beneficiated from the fly ash. Further studies of co-combustion ashes are necessary in order to understand their behavior in disposal

Bioconversion of petroleum hydrocarbons in soil using apple filter cake Bioconversão de hidrocarbonetos de petróleo no solo pelo uso de bagaço de maçã

Directory of Open Access Journals (Sweden)

M. Cecilia Medaura

2008-09-01

Full Text Available The aim of this study was to investigate the feasibility of using apple filter cake, a fruit-processing waste to enhance the bioremediation of petroleum contaminated soil. A rotating barrel system was used to study the bioconversion of the xenobiotic compound by natural occurring microbial population. The soil had been accidentally polluted with a total petroleum hydrocarbon concentration of 41,000 ppm. Although this global value was maintained during the process, microbial intervention was evidenced through transformation of the petroleum fractions. Thus, fractions that represent a risk for the environment (GRO, Gasoline Range Organics i.e., C6 to C10-12; DRO, Diesel Range Organics i.e., C8-12 to C24-26 and RRO, Residual Range Organics i.e., C25 to C35 were significantly reduced, from 2.95% to 1.39%. On the contrary, heavier weight fraction from C35 plus other organics increased in value from 1.15% to 3.00%. The noticeable diminution of low molecular weight hydrocarbons content and hence environmental risk by the process plus the improvement of the physical characteristics of the soil, are promising results with regard to future application at large scale.O objetivo deste estudo foi investigara viabilidade de aplicação de bagaço de maçã, um resíduo do processamento de frutas, para melhorar a biorremediação de solo contaminado com petróleo. Para estudar a bioconversão de compostos xenobióticos pela população microbiana naturalmente presente empregou-se um sistema de barril rotativo. O solo havia sido acidentalmente contaminado com um total de hidrocarbonetos de petróleo na concentração de 41.000 ppm. Embora esse valor tenha se mantido durante o processo, a intervenção microbiana ficou evidenciada através da transformação de frações do petróleo. Assim, as frações de risco para o meio ambiente (GRO, Gasoline Range Organics, i.e., C6 a C10-12; DRO, Diesel Ramge Organics, i.e. C8-12 a C24-26 e RRO, Residual Range Organics

Study on molecular modelling of the selectivity of catalysts for heavy petroleum fractions hydrocracking; Etude sur molecule modele des parametres regissant la selectivite des catalyseurs d'hydrocraquage des charges lourdes

Energy Technology Data Exchange (ETDEWEB)

Leite, L.

2000-10-19

Hydrocracking is a catalytic petroleum refining process that is commonly applied to upgrade the heavier fractions obtained from the distillation of crude oils. Nowadays the European demand for good quality middle distillates (kerosene and gas-oil) is high and one important goal for the refining is to transform selectively feedstocks into middle distillates. To understand how this transformation occurs, studies on model compounds have been investigated. Numerous studies have been devoted to paraffin hydrocracking. However theses molecules do not fully represent heavy petroleum fraction. Taking into account that the trend in the future will be to treat heavier feedstocks containing a large quantity of PNA (Polynuclear Aromatic hydrocarbons), the understanding of their transformation under hydrocracking conditions is a key point. In this study, we studied hydrocracking of phenanthrene over platinum on acid solids catalysts. Our main aim was to compare hydrocracking catalysts in term of catalytic activity and selectivity toward primary products thanks to our model reaction and to correlate these catalytic performances with acid solid properties and especially to rationalize the effects due to the acidity and the porosity of the acid solids. Catalytic experiments emphasised an effect of the porous structure on the selectivities. The acidity of the catalysts seemed to impose the catalytic activity but did not permit to explain the selectivities. This 'effect of the structure' has been clarified with the simulation of intermediate products adsorption and diffusion in the studied structures thanks to a molecular modelling study. Indeed, the selectivities obtained during phenanthrene hydrocracking have been linked up with the intermediate products adsorption energies in the structures. The results of this study permit to propose that the key-step for selectivities determination is the physical desorption of the primary products. (author)

Terminal separation plant for collecting petroleum and by-product gas

Energy Technology Data Exchange (ETDEWEB)

Marinin, N S; Shcherbina, V E; Burma, A I

1966-06-08

A separation plant at a transportation terminal, for collecting petroleum and by-product gas, consists of 1 or 2 vessels with gas separating device, automatic control devices, demulsifier distributors, a mixer for mixing hot water with the demulsified residue and raw crude oil stream, an apparatus for supplying oil-in-water emulsion under a water cushion, and 2 separating partitions which are located at the end of the vessel. In order to fully use the volume of the vessel, one partition does not touch the bottom, while the other does not touch the top of the tank.

Reference data about petroleum fiscality

International Nuclear Information System (INIS)

2006-01-01

This paper explains the different taxes existing in France for the petroleum products (domestic tax on petroleum products, added-value tax), the share of taxes in the retail price, the differences with other European countries, the French Government fiscal receipts and budget. Some information forms are attached to this document and concern: the formation of fuel prices (upstream, refining and transport-distribution margins), the evolution of annual average transport-distribution margins, some reference data about world petroleum markets (supply and demand, prices, market data), and some reference data about the role of oil companies on the petroleum market. (J.S.)

Assessment of the horizontal transfer of functional genes as a suitable approach for evaluation of the bioremediation potential of petroleum-contaminated sites: a mini-review.

Science.gov (United States)

Shahi, Aiyoub; Ince, Bahar; Aydin, Sevcan; Ince, Orhan

2017-06-01

Petroleum sludge contains recalcitrant residuals. These compounds because of being toxic to humans and other organism are of the major concerns. Therefore, petroleum sludge should be safely disposed. Physicochemical methods which are used by this sector are mostly expensive and need complex devices. Bioremediation methods because of being eco-friendly and cost-effective overcome most of the limitations of physicochemical treatments. Microbial strains capable to degrade petroleum hydrocarbons are practically present in all soils and sediments and their population density increases in contact with contaminants. Bacterial strains cannot degrade alone all kinds of petroleum hydrocarbons, rather microbial consortium should collaborate with each other for degradation of petroleum hydrocarbon mixtures. Horizontal transfer of functional genes between bacteria plays an important role in increasing the metabolic potential of the microbial community. Therefore, selecting a suitable degrading gene and tracking its horizontal transfer would be a useful approach to evaluate the bioremediation process and to assess the bioremediation potential of contaminated sites.

Fractionating power and outlet stream polydispersity in asymmetrical flow field-flow fractionation. Part I: isocratic operation.

Science.gov (United States)

Williams, P Stephen

2016-05-01

Asymmetrical flow field-flow fractionation (As-FlFFF) has become the most commonly used of the field-flow fractionation techniques. However, because of the interdependence of the channel flow and the cross flow through the accumulation wall, it is the most difficult of the techniques to optimize, particularly for programmed cross flow operation. For the analysis of polydisperse samples, the optimization should ideally be guided by the predicted fractionating power. Many experimentalists, however, neglect fractionating power and rely on light scattering detection simply to confirm apparent selectivity across the breadth of the eluted peak. The size information returned by the light scattering software is assumed to dispense with any reliance on theory to predict retention, and any departure of theoretical predictions from experimental observations is therefore considered of no importance. Separation depends on efficiency as well as selectivity, however, and efficiency can be a strong function of retention. The fractionation of a polydisperse sample by field-flow fractionation never provides a perfectly separated series of monodisperse fractions at the channel outlet. The outlet stream has some residual polydispersity, and it will be shown in this manuscript that the residual polydispersity is inversely related to the fractionating power. Due to the strong dependence of light scattering intensity and its angular distribution on the size of the scattering species, the outlet polydispersity must be minimized if reliable size data are to be obtained from the light scattering detector signal. It is shown that light scattering detection should be used with careful control of fractionating power to obtain optimized analysis of polydisperse samples. Part I is concerned with isocratic operation of As-FlFFF, and part II with programmed operation.

Petroleum supply annual 1992

International Nuclear Information System (INIS)

1993-01-01

The Petroleum Supply Annual (PSA) contains information on the supply and disposition of crude oil and petroleum products. The publication reflects data that were collected from the petroleum industry during 1992 through annual and monthly surveys. The PSA is divided into two volumes. The first volume contains four sections: Summary Statistics, Detailed Statistics, Refinery Capacity, and Oxygenate Capacity each with final annual data. This second volume contains final statistics for each month of 1992, and replaces data previously published in the Petroleum Supply Monthly (PSM). The tables in Volumes 1 and 2 are similarly numbered to facilitate comparison between them. Explanatory Notes, located at the end of this publication, present information describing data collection, sources, estimation methodology, data quality control procedures, modifications to reporting requirements and interpretation of tables. Industry terminology and product definitions are listed alphabetically in the Glossary

15 CFR Supplement No. 1 to Part 754 - Petroleum and Petroleum Products

Science.gov (United States)

2010-01-01

... fuel (including tractor fuel and stationary turbine fuel). 2710.00.2000 Kerosene derived from petroleum... medicinal grade derived from petroleum, shale oil or both. 3819.00.0000 Hydraulic fluids, including... lubricating oil. 2710.00.3030 Turbine lubricating oil, including marine. 2710.00.3040 Automotive gear oils...

Petroleum investment in Kazakhstan

International Nuclear Information System (INIS)

Friedrich, M.

1994-01-01

There is no specific petroleum legislation as such in place in Kazakhstan and tax legislation is unsophisticated. Regulation of operations is subject to generally applicable legislation. A brief account of the difficulties which exist for both sides in renegotiating a contract is given. Since the competence to enter into contracts with foreign companies has not been fully defined, the first problem when applying for petroleum rights is the identification of a negotiating partner. A summary of terms and conditions and a list of the main laws applicable to petroleum operations are included. (UK)

Novel use of residue from direct coal liquefaction process

Energy Technology Data Exchange (ETDEWEB)

Jianli Yang; Zhaixia Wang; Zhenyu Liu; Yuzhen Zhang [Chinese Academy of Sciences, Taiyuan (China). State Key Laboratory of Coal Conversion

2009-09-15

Direct coal liquefaction residue (DCLR) is, commonly, designed to be used as a feed stock for gasification or combustion. Use of DCLR as a value added product is very important for improving overall economy of direct coal liquefaction processes. This study shows that the DCLR may be used as a pavement asphalt modifier. The modification ability is similar to that of Trinidad Lake Asphalt (TLA), a superior commercial modifier. Asphalts modified by two DCLRs meet the specifications of ASTM D5710 and BSI BS-3690 designated for the TLA-modified asphalts. The required addition amount for the DCLRs tested is less than that for TLA due possibly to the high content of asphaltene in DCLRs. Different compatibility was observed for the asphalts with the same penetration grade but from the different origin. Different components in the DCLR play different roles in the modification. Positive synergetic effects among the fractions were observed, which may due to the formation of the stable colloid structure. Unlike polymer-type modifier, the structure of asphalt-type modifier has a similarity with petroleum asphalts which favors the formation of a stable dispersed polar fluid (DPF) colloid structure and improves the performance of pavement asphalt. 12 refs., 1 fig., 6 tabs.

Selling petroleum to the military

International Nuclear Information System (INIS)

Uscher, R.H.

1999-01-01

This article examines what petroleum products and services the US military buys, the contracts awarded to Asian and European refiners for supplies outside the USA, and military specifications and test methods including the specifications of JP-8 battlefield fuel and the JP-8+100 additive package for military aircraft. The way in which the military buys petroleum products is described, and details are given of the types of military contracts, the bidding on Defense Energy Support Center (DESC) petroleum contracts, the performance of military petroleum contracts, socio-economic programmes, the Prompt Payment Act requiring contractors to be paid promptly, and procedures for claims and disputes

Electrodialytically treated MSWI APC residue as substitute for cement in mortar

DEFF Research Database (Denmark)

Kirkelund, Gunvor Marie; Geiker, Mette Rica; Jensen, Pernille Erland

2014-01-01

Air pollution control (APC) residues from municipal solid waste incineration (MSWI) are considered hazardous waste and need pretreatment prior to possible reuse. Here, two MSWI APC residues, from which the most mobile fraction of heavy metals and salts has been removed by carbonation and/or elect......Air pollution control (APC) residues from municipal solid waste incineration (MSWI) are considered hazardous waste and need pretreatment prior to possible reuse. Here, two MSWI APC residues, from which the most mobile fraction of heavy metals and salts has been removed by carbonation and....../or electrodialytic remediation, were used in Portland cement mortar. Mortar bars with 15 % weight replacement of cement by APC residues showed compressive strengths up to 40 MPa after 28/32 days. Heavy metal and salt leaching from both crushed and monolithic mortars with APC residues was generally similar...

Bio-oil from Flash Pyrolysis of Agricultural Residues

DEFF Research Database (Denmark)

Ibrahim, Norazana

This thesis describes the production of bio-oils from flash pyrolysis of agricultural residues, using a pyrolysis centrifugal reactor (PCR). By thermal degradation of agricultural residues in the PCR, a liquid oil, char and non-condensable gases are produced. The yield of each fraction...

77 FR 42297 - National Petroleum Council

Science.gov (United States)

2012-07-18

... DEPARTMENT OF ENERGY National Petroleum Council AGENCY: Department of Energy, Office of Fossil... National Petroleum Council. The Federal Advisory Committee Act (Pub. L. 92-463, 86 Stat. 770) requires that... Matters Discussion of Any Other Business Properly Brought Before the National Petroleum Council...

76 FR 53889 - National Petroleum Council

Science.gov (United States)

2011-08-30

... DEPARTMENT OF ENERGY National Petroleum Council AGENCY: Department of Energy, Office of Fossil... Petroleum Council. The Federal Advisory Committee Act (Pub. L. 92-463, 86 Stat. 770) requires that public... Properly Brought Before the National, Petroleum Council, Adjournment. Public Participation: The meeting is...

Hydrogen and carbon isotopes of petroleum and related organic matter

International Nuclear Information System (INIS)

Yeh, H.W.; Epstein, S.

1981-01-01

D/H and 13 C/ 12 C ratios were measured for 114 petroleum samples and for several samples of related organic matter. DeltaD of crude oil ranges from -85 to -181 per thousand except for one distillate (-250 per thousand) from the Kenai gas field; delta 13 C of crude oil ranges from -23.3 to -32.5 per thousand. Variation in deltaD and delta 13 C values of compound-grouped fractions of a crude oil is small, 3 and 1.1 per thousand, respectively, and the difference in deltaD and delta 13 C between oil and coeval wax is slight. Gas fractions are 53 to 70 and 22.6 to 23.2 per thousand depleted in D and 13 C, respectively, relative to the coexisting oil fractions. The deltaD and delta 13 C values of the crude oils appear to be largely determined by the isotopic compositions of their organic precursors. The contribution of terrestrial organic debris to the organic precursors of most marine crude oils may be significant. (author)

Petroleum and international policy

International Nuclear Information System (INIS)

Pertuzio, A.

2002-01-01

To illustrate the relation between the petroleum and the international policy, the author presents the place of the petroleum industry in the international relations by an analysis of the historical aspects, the states and international organizations interventions and the prices evolution. (A.L.B.)

Petroleum systems of Indonesia

NARCIS (Netherlands)

Doust, H.; Noble, R.A.

2008-01-01

Indonesia contains many Tertiary basins, several of which have proven to be very prolific producers of oil and gas. The geology and petroleum systems of these productive basins are reviewed, summarized and updated according to the most recent developments. We have linked the recognized petroleum

Caspian sea: petroleum challenges

International Nuclear Information System (INIS)

2005-01-01

The Caspian sea is one of the world areas the most promising in terms of investments and petroleum development. This study presents the petroleum challenges generated by this hydrocarbons reserve. The first part discusses the juridical status (sea or lake), the petroleum and the gas reserves, the ecosystem and the today environment (fishing and caviar), the geostrategic situation and the transport of gas and oil. It provides also a chronology from 1729 to 2005, a selection of Internet sites, books and reports on the subject and identity sheets of the countries around the Caspian sea. (A.L.B.)

Petroleum: the new deal

International Nuclear Information System (INIS)

Magalhaes, St.; Kan, E.

2008-01-01

The drop of oil prices imposes a revision of development and investment strategies of petroleum and para-petroleum companies, while technologies under study try to optimize the exploration and production costs. Following the financial and economical crises, the petroleum industry is preparing its restructuring: new profitability threshold of projects, slowing down of the activity, expected surge of mergers. Despite the crisis, the R and D for the exploitation of tar sands still goes on while on the offshore side, R and D has never been so active to take up the challenge of extreme deep sea conditions. (J.S.)

Basic petroleum research. Final report

International Nuclear Information System (INIS)

Roesjoe, Bjarne; Stiksrud, Helge

2004-01-01

An overview of projects in the field of basic petroleum research (PetroForsk) is presented. A brief presentation of some of the projects is included, as well as political comments on the value of these projects. The research program Basic Petroleum Research (PetroForsk) was established in 1998 and ended in 2004. The program has been part of the Research Council of Norway's long-term effort in petroleum research (ml)

78 FR 40131 - National Petroleum Council

Science.gov (United States)

2013-07-03

... DEPARTMENT OF ENERGY National Petroleum Council AGENCY: Office of Fossil Energy, Department of... Petroleum Council. The Federal Advisory Committee Act (Pub. L. 92-463, 86 Stat. 770) requires that public... Administrative Matters Discussion of Any Other Business Properly Brought Before the National Petroleum Council...

REDUCING POWER PRODUCTION COSTS BY UTILIZING PETROLEUM COKE

Energy Technology Data Exchange (ETDEWEB)

Kevin C. Galbreath; Donald L. Toman; Christopher J. Zygarlicke

1999-09-01

Petroleum coke, a byproduct of the petroleum-refining process, is an attractive primary or supplemental fuel for power production primarily because of a progressive and predictable increase in the production volumes of petroleum coke (1, 2). Petroleum coke is most commonly blended with coal in proportions suitable to meet sulfur emission compliance. Petroleum coke is generally less reactive than coal; therefore, the cofiring of petroleum coke with coal typically improves ignition, flame stability, and carbon loss relative to the combustion of petroleum coke alone. Although petroleum coke is a desirable fuel for producing relatively inexpensive electrical power, concerns about the effects of petroleum coke blending on combustion and pollution control processes exist in the coal-fired utility industry (3). The Energy & Environmental Research Center (EERC) completed a 2-year technical assessment of petroleum coke as a supplemental fuel. A survey questionnaire was sent to seven electric utility companies that are currently cofiring coal and petroleum coke in an effort to solicit specific suggestions on research needs and fuel selections. An example of the letter and survey questionnaire is presented in Appendix A. Interest was expressed by most utilities in evaluating the effects of petroleum coke blending on grindability, combustion reactivity, fouling, slagging, and fly ash emissions control. Unexpectedly, concern over corrosion was not expressed by the utilities contacted. Although all seven utilities responded to the question, only two utilities, Northern States Power Company (NSP) and Ameren, sent fuels to the EERC for evaluation. Both utilities sent subbituminous coals from the Power River Basin and petroleum shot coke samples. Petroleum shot coke is produced unintentionally during operational upsets in the petroleum refining process. This report evaluates the effects of petroleum shot coke blending on grindability, fuel reactivity, fouling/slagging, and

Fact sheet. Norwegian petroleum activity 1996

Energy Technology Data Exchange (ETDEWEB)

Westgaard, T. [ed.

1996-02-01

The present report from the Royal Ministry of Industry and Energy deals with the Norwegian petroleum activity. Main topics are as follow: Historical overview; state organisation of petroleum activities; the economic impact of Norwegian oil and gas; state revenues; mainland activities; petroleum resources; production; marketing situation for petroleum products; environmental aspects; the legal and licence framework; licensing rounds; exploration; fields in production; fields under development; discoveries with development plan under consideration; transportation systems; licence interests; company interests. 36 refs., 24 figs., 15 tabs.

Environmental impact of petroleum products in the soil. Part II: Petroleum products composition and key properties

International Nuclear Information System (INIS)

Zerlia, T.

2001-01-01

The fate of petroleum hydrocarbons in the soil depends on the chemical-physic properties of each hydrocarbon, as well as on the soil characteristics. The mean composition of various petroleum products, the key chemical compounds and their characteristics are focused in order to outline the environmental behaviour of petroleum hydrocarbons in the soil [it

21 CFR 172.888 - Synthetic petroleum wax.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Synthetic petroleum wax. 172.888 Section 172.888... CONSUMPTION Multipurpose Additives § 172.888 Synthetic petroleum wax. Synthetic petroleum wax may be safely used in or on foods in accordance with the following conditions: (a) Synthetic petroleum wax is a...

Solution of fractional-order differential equations based on the operational matrices of new fractional Bernstein functions

Directory of Open Access Journals (Sweden)

M.H.T. Alshbool

2017-01-01

Full Text Available An algorithm for approximating solutions to fractional differential equations (FDEs in a modified new Bernstein polynomial basis is introduced. Writing x→xα(0<α<1 in the operational matrices of Bernstein polynomials, the fractional Bernstein polynomials are obtained and then transformed into matrix form. Furthermore, using Caputo fractional derivative, the matrix form of the fractional derivative is constructed for the fractional Bernstein matrices. We convert each term of the problem to the matrix form by means of fractional Bernstein matrices. A basic matrix equation which corresponds to a system of fractional equations is utilized, and a new system of nonlinear algebraic equations is obtained. The method is given with some priori error estimate. By using the residual correction procedure, the absolute error can be estimated. Illustrative examples are included to demonstrate the validity and applicability of the presented technique.

Phosphorus fractionation and crop performance on an alfisol ...

African Journals Online (AJOL)

The effects of Sokoto phosphate rock (PR) and plant residues on soil phosphorus (P) fractions and crop performance was studied in the field on an alfisol in the derived savanna of southwestern Nigeria. The plant residues studied were leaves of Dactyladenia barteri, Flemingia macrophylla, Gliricidia sepium, Leucaena ...

Petroleum coke as energy source: an update

International Nuclear Information System (INIS)

Pinelli, G.

2008-01-01

A previous review presented a critical evaluation of the use of petroleum coke as energy source. After some years, with reference to increased petroleum coke production, that paper is revised. In particular, the attention is now focused on world petroleum coke market trends and, in regard to petroleum coke used as fuel, on new Italian environment laws. [it

Two-stage catalytic up-grading of vacuum residue of a Wandoan coal liquid. [Vacuum residue of coal liquid

Energy Technology Data Exchange (ETDEWEB)

Mochida, I.; Sakanishi, K.; Korai, Y.; Fujitsu, H.

1986-08-01

A successive two-stage hydrotreatment using a commercial Ni-Mo/Al/sub 2/O/sub 3/ catalyst (HDN-30) was applied to the vacuum residue of a Wandoan coal liquid to achieve high levels of hydrocracking, hydrodenitrogenation and hydrodeoxygenation. Two-stage hydrotreatment in 1-methylnaphthalene containing 20wt% fluoranthene as a solvent at solvent/coal liquid ratio of unity removed 83% (overall) of nitrogen and 90% (overall) of oxygen in the asphaltene (benzene-soluble fraction) at 380/sup 0/C for 3 h and at 420/sup 0/C for 3h under hydrogen pressure of 15 MPa and 14 MPa, respectively, while the single stage treatment at 420/sup 0/C for 3 h removed only 41% and 46%, respectively. The same two-stage treatment allowed the overall denitrogenation of 51% and the overall deoxygenation of 67% from a mixture of asphaltene and preasphaltene (THF-soluble fraction). Addition of the catalyst prior to the second stage reaction increased the removal of nitrogen and oxygen to 75 and 82%, respectively, indicating significant catalyst deactivation by the preasphaltene fraction in the first stage. Increasing the solvent/coal liquid ratio to 2 or addition of tetrahydrofluoranthene as a component of the solvent increased the removal of nitrogen and oxygen to 70 and 80%, respectively. Such two-stage hydrotreatment was also effective in refining the whole residue, allowing denitrogenations and deoxygenations of 68 and 75% respectively using tetrahydrofluoranthene. The coke, unreacted coal and minerals in the residue may not cause acute catalyst deactivation. High dissolving ability of the reaction solvents is very effective to decrease catalyst deactivation by carbon deposition. The successive two-stage hydrotreatment also enhanced hydrocracking of polar and resin fractions in the residue into oils (conversion, 65%). (Abstract Truncated)

Petroleum.

Science.gov (United States)

McManus, T. R.; And Others

1989-01-01

This review of petroleum covers: crude oil; fuels, gaseous and liquid; lubricants, oils, and greases; asphalts, bitumens, tars, and pitches; hydrocarbons; physical properties; metals in oil; nonmetallic elements and heterocompounds; and analytical methods and apparatus. (MVL)

Naval Petroleum and Oil Shale Reserves

International Nuclear Information System (INIS)

1992-01-01

During fiscal year 1992, the reserves generated $473 million in revenues, a $181 million decrease from the fiscal year 1991 revenues, primarily due to significant decreases in oil and natural gas prices. Total costs were $200 million, resulting in net cash flow of $273 million, compared with $454 million in fiscal year 1991. From 1976 through fiscal year 1992, the Naval Petroleum and Oil Shale Reserves generated more than $15 billion in revenues and a net operating income after costs of $12.5 billion. In fiscal year 1992, production at the Naval Petroleum Reserves at maximum efficient rates yielded 26 million barrels of crude oil, 119 billion cubic feet of natural gas, and 164 million gallons of natural gas liquids. From April to November 1992, senior managers from the Naval Petroleum and Oil Shale Reserves held a series of three workshops in Boulder, Colorado, in order to build a comprehensive Strategic Plan as required by Secretary of Energy Notice 25A-91. Other highlights are presented for the following: Naval Petroleum Reserve No. 1--production achievements, crude oil shipments to the strategic petroleum reserve, horizontal drilling, shallow oil zone gas injection project, environment and safety, and vanpool program; Naval Petroleum Reserve No. 2--new management and operating contractor and exploration drilling; Naval Petroleum Reserve No. 3--steamflood; Naval Oil Shale Reserves--protection program; and Tiger Team environmental assessment of the Naval Petroleum and Oil Shale Reserves in Colorado, Utah, and Wyoming

Effects of the petroleum tax reform

International Nuclear Information System (INIS)

Stensland, G.; Sunnevaag, K.; Tennfjord, B.S.

1992-04-01

The report evaluates the effects of the petroleum taxation in Norway. In connection with the general reform of the Norwegian industry taxation, changes are proposed in the petroleum tax law. The report gives a survey of the development in the Norwegian petroleum taxation, and analyses the effects of changing the tax revenue both for the Government and for the companies concerned. The effects of incentives caused by changing the taxation are looked upon. In the appendix the depreciation rules in connection with petroleum taxation are discussed. 18 refs., 17 figs

The petroleum industry in 1999 (editorial)

International Nuclear Information System (INIS)

2001-01-01

This document deals with the petroleum activity in 1999. It provides three economic analysis. The first one concerns the petroleum industry activity in 1999 and the corresponding french energy policy. The second one presents the petroleum activity in the world. The third one presents the hydrocarbons market supplying in France. (A.L.B.)

Canadian retail petroleum markets study

International Nuclear Information System (INIS)

Ervin, M.J.

1998-02-01

A retail petroleum market study was conducted to provide a comprehensive overview of the competitiveness of the downstream petroleum industry in Canada and to set a foundation for effective policy development. The downstream petroleum industry, which includes the petroleum refining and marketing sectors, faces a poor public image, competitive pressures from U.S. and offshore refiners, and a broad range of environmental challenges. In this study, 19 markets representing a wide range of conditions were chosen for a detailed review of outlet economics. A market-by-market and regional comparisons of key competitiveness indicators was made in order to identify market and regional competitive differences as potential issues or opportunities within the industry. The study also included a pump price/margin model and provided a general overview of the retail gasoline sub-sector in terms of infrastructure. A review of prices, margins and demand patterns over the past several years was also undertaken to show the relationship between consumer demand patterns and pump price fluctuations. The study presented 22 findings which led to several conclusions and recommendations regarding the competitiveness of Canada's petroleum marketing sector. Two of the key conclusions were that taxation is a significant factor in the price of retail gasoline (about 50 per cent) and that government intervention into petroleum marketing is likely to be a poor alternative to market-based regulation. 18 tabs., 37 figs

The para-petroleum industry

International Nuclear Information System (INIS)

2002-07-01

The para-petroleum industry includes societies that realize studies and installations for the deposits exploitation. This document presents the situation of the para-petroleum industry in 2001, the world investment growth of the activity, the french societies financial results and an inventory of the main operations in the amalgamation domain. (A.L.B.)

Remaining Sites Verification Package for the 600-243 Petroleum-Contaminated Soil Bioremediation Pad. Attachment to Waste Site Reclassification Form 2007-033

International Nuclear Information System (INIS)

Capron, J.M.

2008-01-01

The 600-243 waste site consisted of a bioremediation pad for petroleum-contaminated soils resulting from the 1100 Area Underground Storage Tank (UST) upgrades in 1994. In accordance with this evaluation, the verification sampling results support a reclassification of this site to Interim Closed Out. The results of verification sampling show that residual contaminant concentrations do not preclude any future uses and allow for unrestricted use of shallow zone soils. The results also demonstrate that residual contaminant concentrations are protective of groundwater and the Columbia River

Computer simulation of deasphalting vacuum residues in a pilot unit; Simulacao computacional de desasfaltacao de residuo de vacuo realizada em unidade piloto

Energy Technology Data Exchange (ETDEWEB)

Concha, Viktor Oswaldo Cardenas; Quirino, Filipe Augusto Barral; Koroisgi, Erika Tomie; Rivarola, Florencia Wisnivesky Rocca; Maciel, Maria Regina Wolf; Maciel Filho, Rubens [Universidade Estadual de Campinas (UNICAMP), SP (Brazil). Faculdade de Engenharia Quimica; Medina, Lilian Carmen; Barros, Ricardo Soares de [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil). Centro de Pesquisas (CENPES)

2008-07-01

In the context of the national petroleum industry, it is interesting to keep the production of the paraffinic lubricant oil type I, which implies in the identification of new loads to ensure the feeding of the existing units. Therefore, it is important to carry out carefully the characterization of the oils, defining its potential for fuel, asphalt and lubricant. Aiming to introduce in the characterization and evaluation of petroleum for lubricant, carried out by PETROBRAS/CENPES, information of basic oils, more similar to industrial oils, was built up in the Laboratory of Process Separation Development - LDPS of UNICAMP/FEQ, a deasphalting pilot unit. In this work, the deasphalting process of a vacuum residue of Brazilian petroleum is simulated, using Aspen Plus{sup R} simulator, in order to remove asphaltenes, resins and other heavy components of vacuum residue. The simulations were carried out considering the configuration of the pilot plant, evaluating the extraction in near-critical operational condition applied to a petroleum, using propane as the solvent. The extraction efficiency and the solvent power were evaluated considering variations in temperature, pressure and in the solvent/feed ratio in order to obtain yields with more efficiency in the production of deasphalted oil (DAO), what means more asphaltene removal. (author)

BIOREMEDIATION OF A PETROLEUM-HYDROCARBON

African Journals Online (AJOL)

ES OBE

under field conditions in the bioremediation of a petroleum- hydrocarbon polluted ... an accelerated biodegradation of petroleum hydrocarbons in a polluted agricultural soil ..... 12) Jackson, M.L. Soil chemical analysis. ... biological assay. 3 rd.

The 1999 MWV petroleum consumption forecast: Petroleum still in the lead in the German energy market

International Nuclear Information System (INIS)

Anon.

1999-01-01

Petroleum consumption in Germany has been stagnant over the last few years. Since in 1998 the decline in light heating oil sales was balanced out by an increase in fuel consumption and petroleum sales to the petrochemical industry, total domestic supplies of petroleum products amounted to 127.4 million tonnes and thus remained at last year's level. According to the latest forecast of the Mineraloelwirtschaftsverband e.V., extending to the year 2010, stagnation will continue for some years, but petroleum consumption is expected to then take a clear downward trend and fall off by 11 million tonnes (or 9%) until 2010. (orig./CB) [de

Influence of dispersants on trophic transfer of petroleum hydrocarbons in a marine food chain

Energy Technology Data Exchange (ETDEWEB)

Wolfe, M.; Tjeerdema, R. [Univ. of California, Santa Cruz, CA (United States). Dept. of Chemistry and Biochemistry; Sowby, M. [California Dept. of Fish and Game, Sacramento, CA (United States)

1995-12-31

When crude oil is accidentally released into the ocean, it threatens many levels of marine life. Intervention, in the form of chemical dispersing agents, alters the normal behavior of petroleum hydrocarbons (PH) by increasing their functional water solubility and the extent of their exposure to sub-surface organisms. Dispersing agents may modify bioavailability as a result of altered interactions between dispersed PH droplets and organismal cell membranes.The objective of this research was to determine the impact of dispersing agents on PH bioavailability and trophic transfer in primary levels of a marine food chain. Uptake, bioaccumulation, depuration, and metabolic transformation of a model PH, {sup 14}C-naphthalene, were measured and compared for Prudhoe Bay Crude Oil (PBCO) dispersed with Corexit 9527 and undispersed preparations of the water-accommodated fractions (WAF) of PBCO at two salinities and temperatures. The model food chain consisted of Isochrysis galbana and Brachionus plicatilis. Direct aqueous exposure was compared with combined aqueous and dietary exposure. Fractionation and identification of metabolites was done by HPLC co-chromatography with analytical standards, and quantitation was done by liquid scintillation counting. GC-FID characterization of WAF and dispersed oil (DO) preparations shows higher concentrations of petroleum hydrocarbons and a greater number of individual constituents in the dispersed oil preparations.